Electric vehicle recycling 2020: Key component power electronics.

PubMed

Bulach, Winfried; Schüler, Doris; Sellin, Guido; Elwert, Tobias; Schmid, Dieter; Goldmann, Daniel; Buchert, Matthias; Kammer, Ulrich

2018-04-01

Electromobility will play a key role in order to reach the specified ambitious greenhouse gas reduction targets in the German transport sector of 42% between 1990 and 2030. Subsequently, a significant rise in the sale of electric vehicles (EVs) is to be anticipated in future. The amount of EVs to be recycled will rise correspondingly after a delay. This includes the recyclable power electronics modules which are incorporated in every EV as an important component for energy management. Current recycling methods using car shredders and subsequent post shredder technologies show high recycling rates for the bulk metals but are still associated with high losses of precious and strategic metals such as gold, silver, platinum, palladium and tantalum. For this reason, the project 'Electric vehicle recycling 2020 - key component power electronics' developed an optimised recycling route for recycling power electronics modules from EVs which is also practicable in series production and can be implemented using standardised technology. This 'WEEE recycling route' involves the disassembly of the power electronics from the vehicle and a subsequent recycling in an electronic end-of-life equipment recycling plant. The developed recycling process is economical under the current conditions and raw material prices, even though it involves considerably higher costs than recycling using the car shredder. The life cycle assessment shows basically good results, both for the traditional car shredder route and the developed WEEE recycling route: the latter provides additional benefits from some higher recovery rates and corresponding credits.

Comparisons of four categories of waste recycling in China's paper industry based on physical input-output life-cycle assessment model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liang Sai; Zhang, Tianzhu, E-mail: zhangtz@mail.tsinghua.edu.cn; Xu Yijian

Highlights: Black-Right-Pointing-Pointer Using crop straws and wood wastes for paper production should be promoted. Black-Right-Pointing-Pointer Bagasse and textile waste recycling should be properly limited. Black-Right-Pointing-Pointer Imports of scrap paper should be encouraged. Black-Right-Pointing-Pointer Sensitivity analysis, uncertainties and policy implications are discussed. - Abstract: Waste recycling for paper production is an important component of waste management. This study constructs a physical input-output life-cycle assessment (PIO-LCA) model. The PIO-LCA model is used to investigate environmental impacts of four categories of waste recycling in China's paper industry: crop straws, bagasse, textile wastes and scrap paper. Crop straw recycling and wood utilization for papermore » production have small total intensity of environmental impacts. Moreover, environmental impacts reduction of crop straw recycling and wood utilization benefits the most from technology development. Thus, using crop straws and wood (including wood wastes) for paper production should be promoted. Technology development has small effects on environmental impacts reduction of bagasse recycling, textile waste recycling and scrap paper recycling. In addition, bagasse recycling and textile waste recycling have big total intensity of environmental impacts. Thus, the development of bagasse recycling and textile waste recycling should be properly limited. Other pathways for reusing bagasse and textile wastes should be explored and evaluated. Moreover, imports of scrap paper should be encouraged to reduce large indirect impacts of scrap paper recycling on domestic environment.« less

Utilizing Coal Fly Ash and Recycled Glass in Developing Green Concrete Materials

DOT National Transportation Integrated Search

2012-06-01

The environmental impact of Portland cement concrete production has motivated researchers and the construction industry to evaluate alternative technologies for incorporating recycled cementing materials and recycled aggregates in concrete. One such ...

Quality requirements for reclaimed/recycled water

NASA Technical Reports Server (NTRS)

Janik, Daniel S.; Sauer, Richard L.; Pierson, Duane L.; Thorstenson, Yvonne R.

1987-01-01

Water used during current and previous space missions has been either carried or made aloft. Future human space endeavors will require some form of water reclamation and recycling. There is little experience in the U.S. space program with this technology. Water reclamation and recycling constitute engineering challenges of the broadest nature that will require an intensive research and development effort if this technology is to mature in time for practical use on the proposed U.S. Space Station. In order for this to happen, reclaimed/recycled water specifications will need to be devised to guide engineering development. Present NASA Potable Water Specifications are not applicable to reclaimed or recycled water. Adequate specifications for ensuring the quality of the reclaimed or recycled potable water system is reviewed, limitations of present water specifications are examined, world experience with potable water reclamation/recycling systems and systems analogs is reviewed, and an approach to developing pertinent biomedical water specifications for spacecraft is presented. Space Station water specifications should be designed to ensure the health of all likely spacecraft inhabitants including man, animals, and plants.

Designing Recycled Hot Mix Asphalt Mixtures Using Superpave Technology

DOT National Transportation Integrated Search

1997-01-01

Mix design procedures for recycled asphalt pavements require the selection of : virgin asphalt binder or recycling agent. This research project was undertaken : to develop a procedure for selecting the performance grade (PG) of virgin : asphalt binde...

Developing Statistical Evaluation Model of Introduction Effect of MSW Thermal Recycling

NASA Astrophysics Data System (ADS)

Aoyama, Makoto; Kato, Takeyoshi; Suzuoki, Yasuo

For the effective utilization of municipal solid waste (MSW) through a thermal recycling, new technologies, such as an incineration plant using a Molten Carbonate Fuel Cell (MCFC), are being developed. The impact of new technologies should be evaluated statistically for various municipalities, so that the target of technological development or potential cost reduction due to the increased cumulative number of installed system can be discussed. For this purpose, we developed a model for discussing the impact of new technologies, where a statistical mesh data set was utilized to estimate the heat demand around the incineration plant. This paper examines a case study by using a developed model, where a conventional type and a MCFC type MSW incineration plant is compared in terms of the reduction in primary energy and the revenue by both electricity and heat supply. Based on the difference in annual revenue, we calculate the allowable investment in MCFC-type MSW incineration plant in addition to conventional plant. The results suggest that allowable investment can be about 30 millions yen/(t/day) in small municipalities, while it is only 10 millions yen/(t/day) in large municipalities. The sensitive analysis shows the model can be useful for discussing the difference of impact of material recycling of plastics on thermal recycling technologies.

Disposing and recycling waste printed circuit boards: disconnecting, resource recovery, and pollution control.

PubMed

Wang, Jianbo; Xu, Zhenming

2015-01-20

Over the past decades, China has been suffering from negative environmental impacts from distempered e-waste recycling activities. After a decade of effort, disassembly and raw materials recycling of environmentally friendly e-waste have been realized in specialized companies, in China, and law enforcement for illegal activities of e-waste recycling has also been made more and more strict. So up to now, the e-waste recycling in China should be developed toward more depth and refinement to promote industrial production of e-waste resource recovery. Waste printed circuit boards (WPCBs), which are the most complex, hazardous, and valuable components of e-waste, are selected as one typical example in this article that reviews the status of related regulations and technologies of WPCBs recycling, then optimizes, and integrates the proper approaches in existence, while the bottlenecks in the WPCBs recycling system are analyzed, and some preliminary experiments of pinch technologies are also conducted. Finally, in order to provide directional guidance for future development of WPCBs recycling, some key points in the WPCBs recycling system are proposed to point towards a future trend in the e-waste recycling industry.

Waste Printed Circuit Board (PCB) Recycling Techniques.

PubMed

Ning, Chao; Lin, Carol Sze Ki; Hui, David Chi Wai; McKay, Gordon

2017-04-01

With the development of technologies and the change of consumer attitudes, the amount of waste electrical and electronic equipment (WEEE) is increasing annually. As the core part of WEEE, the waste printed circuit board (WPCB) is a dangerous waste but at the same time a rich resource for various kinds of materials. In this work, various WPCB treatment methods as well as WPCB recycling techniques divided into direct treatment (landfill and incineration), primitive recycling technology (pyrometallurgy, hydrometallurgy, biometallurgy and primitive full recovery of NMF-non metallic fraction), and advanced recycling technology (mechanical separation, direct use and modification of NMF) are reviewed and analyzed based on their advantages and disadvantages. Also, the evaluation criteria are discussed including economic, environmental, and gate-to-market ability. This review indicates the future research direction of WPCB recycling should focus on a combination of several techniques or in series recycling to maximize the benefits of process.

A review on management of spent lithium ion batteries and strategy for resource recycling of all components from them.

PubMed

Zhang, Wenxuan; Xu, Chengjian; He, Wenzhi; Li, Guangming; Huang, Juwen

2018-02-01

The wide use of lithium ion batteries (LIBs) has brought great numbers of discarded LIBs, which has become a common problem facing the world. In view of the deleterious effects of spent LIBs on the environment and the contained valuable materials that can be reused, much effort in many countries has been made to manage waste LIBs, and many technologies have been developed to recycle waste LIBs and eliminate environmental risks. As a review article, this paper introduces the situation of waste LIB management in some developed countries and in China, and reviews separation technologies of electrode components and refining technologies of LiCoO 2 and graphite. Based on the analysis of these recycling technologies and the structure and components characteristics of the whole LIB, this paper presents a recycling strategy for all components from obsolete LIBs, including discharge, dismantling, and classification, separation of electrode components and refining of LiCoO 2 /graphite. This paper is intended to provide a valuable reference for the management, scientific research, and industrial implementation on spent LIBs recycling, to recycle all valuable components and reduce the environmental pollution, so as to realize the win-win situation of economic and environmental benefits.

Efficiency enhancement of liquid crystal projection displays using light recycle technology

NASA Technical Reports Server (NTRS)

Wang, Y.

2002-01-01

A new technology developed at JPL using low absorption color filters with polarization and color recycle system, is able to enhance efficiency of a single panel liquid crytal display (LCD) projector to the same efficiency of a 3 panel LCD projector.

Optics Recycle Loop Strategy for NIF Operations above UV Laser-Induced Damage Threshold

DOE PAGES

Spaeth, M. L.; Wegner, P. J.; Suratwala, T. I.; ...

2017-03-23

The National Ignition Facility (NIF) at Lawrence Livermore National Laboratory (LLNL) houses the world’s largest laser system, composed of 192 individual, 40-cm-aperture beamlines. The NIF laser routinely operates at ultraviolet (UV) fluences above 8 J/cm 2, more than twice the (3ω only) damage threshold of commercially available UV-grade fused silica. NIF is able to maintain such high fluence operation by using an optics recycling loop strategy. Successful operation of the loop relies on a number of technologies specifically developed for NIF. One of the most important is the capability developed by LLNL and their vendors for producing highly damage-resistant optics.more » Other technologies developed for the optics recycle loop raise the operating point of NIF by keeping damage growth in check. LLNL has demonstrated the capability to sustain UV fused silica optic recycling rates of up to 40 optics per week. The optics are ready for reinstallation after a 3-week trip through a recycle loop where the damage state of each optic is assessed and repaired. The impact of the optics recycle loop has been profound, allowing the experimental program to routinely employ energies and fluences that would otherwise have been unachievable. Without the recycle loop, it is likely that the NIF fluence would need to be kept below the UV threshold for damage growth, ~4 J/cm 2, thus keeping the energy delivered to the target significantly below 1 MJ. With the recycle loop implemented during the National Ignition Campaign, NIF can routinely deliver >1.8 MJ on target, an increase in operational capability of more than 100%. Finally, in this paper, the enabling technological advances, optical performance, and operational capability implications of the optics recycle loop are discussed.« less

Optics Recycle Loop Strategy for NIF Operations above UV Laser-Induced Damage Threshold

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spaeth, M. L.; Wegner, P. J.; Suratwala, T. I.

The National Ignition Facility (NIF) at Lawrence Livermore National Laboratory (LLNL) houses the world’s largest laser system, composed of 192 individual, 40-cm-aperture beamlines. The NIF laser routinely operates at ultraviolet (UV) fluences above 8 J/cm 2, more than twice the (3ω only) damage threshold of commercially available UV-grade fused silica. NIF is able to maintain such high fluence operation by using an optics recycling loop strategy. Successful operation of the loop relies on a number of technologies specifically developed for NIF. One of the most important is the capability developed by LLNL and their vendors for producing highly damage-resistant optics.more » Other technologies developed for the optics recycle loop raise the operating point of NIF by keeping damage growth in check. LLNL has demonstrated the capability to sustain UV fused silica optic recycling rates of up to 40 optics per week. The optics are ready for reinstallation after a 3-week trip through a recycle loop where the damage state of each optic is assessed and repaired. The impact of the optics recycle loop has been profound, allowing the experimental program to routinely employ energies and fluences that would otherwise have been unachievable. Without the recycle loop, it is likely that the NIF fluence would need to be kept below the UV threshold for damage growth, ~4 J/cm 2, thus keeping the energy delivered to the target significantly below 1 MJ. With the recycle loop implemented during the National Ignition Campaign, NIF can routinely deliver >1.8 MJ on target, an increase in operational capability of more than 100%. Finally, in this paper, the enabling technological advances, optical performance, and operational capability implications of the optics recycle loop are discussed.« less

Secondary resources and recycling in developing economies.

PubMed

Raghupathy, Lakshmi; Chaturvedi, Ashish

2013-09-01

Recycling of metals extends the efficient use of minerals and metals, reduces pressure on environment and results in major energy savings in comparison to primary production. In developing economies recycling had been an integral part of industrial activity and has become a major concern due to the handling of potentially hazardous material without any regard to the occupational health and safety (OH&S) needs. With rising awareness and interest from policy makers, the recycling scenario is changing and the large scale enterprises are entering the recycling sector. There is widespread expectation that these enterprises would use the Best Available Technologies (BAT) leading to better environment management and enhanced resource recovery. The major challenge is to enhance and integrate the activities of other stakeholders in the value chain to make recycling an economically viable and profitable enterprise. This paper is an attempt to propose a sustainable model for recycling in the developing economies through integration of the informal and formal sectors. The main objective is to augment the existing practices using a scientific approach and providing better technology without causing an economic imbalance to the present practices. In this paper studies on lead acid batteries and e-waste recycling in India are presented to evolve a model for "green economy". Copyright © 2013 Elsevier B.V. All rights reserved.

From electronic consumer products to e-wastes: Global outlook, waste quantities, recycling challenges.

PubMed

Tansel, Berrin

2017-01-01

Advancements in technology, materials development, and manufacturing processes have changed the consumer products and composition of municipal solid waste (MSW) since 1960s. Increasing quantities of discarded consumer products remain a major challenge for recycling efforts, especially for discarded electronic products (also referred as e-waste). The growing demand for high tech products has increased the e-waste quantities and its cross boundary transport globally. This paper reviews the challenges associated with increasing e-waste quantities. The increasing need for raw materials (especially for rare earth and minor elements) and unregulated e-waste recycling operations in developing and underdeveloped counties contribute to the growing concerns for e-waste management. Although the markets for recycled materials are increasing; there are major challenges for development of the necessary infrastructure for e-waste management and accountability as well as development of effective materials recovery technologies and product design. Copyright © 2016 Elsevier Ltd. All rights reserved.

Bio-recycling of metals: Recycling of technical products using biological applications.

PubMed

Pollmann, Katrin; Kutschke, Sabine; Matys, Sabine; Raff, Johannes; Hlawacek, Gregor; Lederer, Franziska L

2018-03-16

The increasing demand of different essential metals as a consequence of the development of new technologies, especially in the so called "low carbon technologies" require the development of innovative technologies that enable an economic and environmentally friendly metal recovery from primary and secondary resources. There is serious concern that the demand of some critical elements might exceed the present supply within a few years, thus necessitating the development of novel strategies and technologies to meet the requirements of industry and society. Besides an improvement of exploitation and processing of ores, the more urgent issue of recycling of strategic metals has to be enforced. However, current recycling rates are very low due to the increasing complexity of products and the low content of certain critical elements, thus hindering an economic metal recovery. On the other hand, increasing environmental consciousness as well as limitations of classical methods require innovative recycling methodologies in order to enable a circular economy. Modern biotechnologies can contribute to solve some of the problems related to metal recycling. These approaches use natural properties of organisms, bio-compounds, and biomolecules to interact with minerals, materials, metals, or metal ions such as surface attachment, mineral dissolution, transformation, and metal complexation. Further, modern genetic approaches, e.g. realized by synthetic biology, enable the smart design of new chemicals. The article presents some recent developments in the fields of bioleaching, biosorption, bioreduction, and bioflotation, and their use for metal recovery from different waste materials. Currently only few of these developments are commercialized. Major limitations are high costs in comparison to conventional methods and low element selectivity. The article discusses future trends to overcome these barriers. Especially interdisciplinary approaches, the combination of different technologies, the inclusion of modern genetic methods, as well as the consideration of existing, yet unexplored natural resources will push innovations in these fields. Copyright © 2018 Elsevier Inc. All rights reserved.

Innovative Chemical Process for Recycling Thermosets Cured with Recyclamines® by Converting Bio-Epoxy Composites in Reusable Thermoplastic—An LCA Study

PubMed Central

Banatao, Diosdado R.; Pastine, Stefan J.

2018-01-01

An innovative recycling process for thermoset polymer composites developed by Connora Technologies (Hayward, CA, USA) was studied. The process efficacy has already been tested, and it is currently working at the plant level. The main aspect investigated in the present paper was the environmental impact by means of the Life Cycle Assessment (LCA) method. Because of the need to recycle and recover materials at their end of life, the Connora process creates a great innovation in the market of epoxy composites, as they are notoriously not recyclable. Connora Technologies developed a relatively gentle chemical recycling process that induces the conversion of thermosets into thermoplastics. The LCA demonstrated that low environmental burdens are associated with the process itself and, furthermore, impacts are avoided due to the recovery of the epoxy-composite constituents (fibres and matrix). A carbon fibre (CF) epoxy-composite panel was produced through Vacuum Resin Transfer Moulding (VRTM) and afterwards treated using the Connora recycling process. The LCA results of both the production and the recycling phases are reported. PMID:29495571

Environmental application of gamma technology: Update on the Canadian sludge irradiator

NASA Astrophysics Data System (ADS)

Swinwood, Jean F.; Fraser, Frank M.

1993-10-01

Waste treatment and disposal technologies have recently been subjected to increasing public and regulatory scrutiny. Concern for the environment and a heightened awareness of potential health hazards that could result from insufficient or inappropriate waste handling methods have combined to push waste generators in their search for new treatment alternatives. Gamma technology can offer a new option for the treatment of potentially infectious wastes, including municipal sewage sludge. Sewage sludge contains beneficial plant nutrients and a high organic component that make it ideal as a soil conditioning agent or fertilizer bulking material. It also carries potentially infectious microorganisms which limit opportunities for beneficial recycling of sludges. Gamma irradiation-disinfection of these sludges offers a reliable, fast and efficient method for safe sludge recycling. Nordion International's Market Development Division was created in 1987 as part of a broad corporate reorganization. It was given an exclusive mandate to develop new applications of gamma irradiation technology and markets for these new applications. Nordion has since explored and developed opportunities in food irradiation, pharmaceutical/cosmetic products irradiation, biomedical waste sterilization, airline waste disinfection, and sludge disinfection for recycling. This paper focuses on the last of these -a proposed sludge recycling facility that incorporates a cobalt 60 sludge irradiator.

Peo Life Cycle Cost Accountability: Viability Of Foreign Suppliers For Weapon System Development

DTIC Science & Technology

2016-02-16

i AIR WAR COLLEGE AIR UNIVERSITY PEO LIFE CYCLE COST ACCOUNTABILITY: VIABILITY OF FOREIGN SUPPLIERS FOR WEAPON SYSTEM DEVELOPMENT By...to decrease, then recycling may become more economically feasible. The need for the U.S. to develop affordable technologies for recycling has become

Physical/chemical closed-loop water-recycling for long-duration missions

NASA Technical Reports Server (NTRS)

Herrmann, Cal C.; Wydeven, Ted

1990-01-01

Water needs, water sources, and means for recycling water are examined in terms appropriate to the water quality requirements of a small crew and spacecraft intended for long duration exploration missions. Inorganic, organic, and biological hazards are estimated for waste water sources. Sensitivities to these hazards for human uses are estimated. The water recycling processes considered are humidity condensation, carbon dioxide reduction, waste oxidation, distillation, reverse osmosis, pervaporation, electrodialysis, ion exchange, carbon sorption, and electrochemical oxidation. Limitations and applications of these processes are evaluated in terms of water quality objectives. Computerized simulation of some of these chemical processes is examined. Recommendations are made for development of new water recycling technology and improvement of existing technology for near term application to life support systems for humans in space. The technological developments are equally applicable to water needs on earth, in regions where extensive water ecycling is needed or where advanced water treatment is essential to meet EPA health standards.

Recycling carbon fibre reinforced polymers for structural applications: technology review and market outlook.

PubMed

Pimenta, Soraia; Pinho, Silvestre T

2011-02-01

Both environmental and economic factors have driven the development of recycling routes for the increasing amount of carbon fibre reinforced polymer (CFRP) waste generated. This paper presents a review of the current status and outlook of CFRP recycling operations, focusing on state-of-the-art fibre reclamation and re-manufacturing processes, and on the commercialisation and potential applications of recycled products. It is shown that several recycling and re-manufacturing processes are reaching a mature stage, with implementations at commercial scales in operation, production of recycled CFRPs having competitive structural performances, and demonstrator components having been manufactured. The major challenges for the sound establishment of a CFRP recycling industry and the development of markets for the recyclates are summarised; the potential for introducing recycled CFRPs in structural components is discussed, and likely promising applications are investigated. Copyright © 2010 Elsevier Ltd. All rights reserved.

Global status of recycling waste solar panels: A review.

PubMed

Xu, Yan; Li, Jinhui; Tan, Quanyin; Peters, Anesia Lauren; Yang, Congren

2018-05-01

With the enormous growth in the development and utilization of solar-energy resources, the proliferation of waste solar panels has become problematic. While current research into solar panels has focused on how to improve the efficiency of the production capacity, the dismantling and recycling of end-of-life (EOL) panels are seldom considered, as can be seen, for instance, in the lack of dedicated solar-panel recycling plants. EOL solar-panel recycling can effectively save natural resources and reduce the cost of production. To address the environmental conservation and resource recycling issues posed by the huge amount of waste solar panels regarding environmental conservation and resource recycling, the status of the management and recycling technologies for waste solar panels are systemically reviewed and discussed in this article. This review can provide a quantitative basis to support the recycling of PV panels, and suggests future directions for public policy makers. At present, from the technical aspect, the research on solar panel recovery is facing many problems, and we need to further develop an economically feasible and non-toxic technology. The research on solar photovoltaic panels' management at the end of life is just beginning in many countries, and there is a need for further improvement and expansion of producer responsibility. Copyright © 2018 Elsevier Ltd. All rights reserved.

In-Space Recycler Technology Demonstration

NASA Technical Reports Server (NTRS)

Hoyt, Rob; Werkheiser, NIKI; Kim, Tony

2016-01-01

In 2014, a 3D printer was installed and used successfully on the International Space Station (ISS), creating the first additively manufactured part in space. While additive manufacturing is a game changing technology for exploration missions, the process still requires raw feedstock material to fabricate parts. Without a recycling capability, a large supply of feedstock would need to be stored onboard, which negates the logistical benefits of these capabilities. Tethers Unlimited, Inc. (TUI), received a Small Business Innovation Research (SBIR) award to design and build the first In-space Recycler for demonstration aboard the ISS in 2017. To fully test this technology in microgravity, parts will be 3D printed, recycled into reusable filament, and then reprinted into new parts. Recycling scrap into printer filament is quite challenging in that a recycler must be able to handle a large variety of possible scrap configurations and densities. New challenges include: dealing with inevitable contamination of the scrap material, minimizing damage to the molecular structure of the plastic during reprocessing, managing a larger volume of hot liquid plastic, and exercising greater control over the cooling/resolidification of the material. TUI has developed an architecture that addresses these challenges by combining standard, proven technologies with novel, patented processes developed through this effort. Results show that the filament diameter achieved is more consistent than commercial filament, with only minimal degradation of material properties over recycling steps. In May 2016, TUI completed fabrication of a flight prototype, which will ultimately progress to the demonstration unit for the ISS as a testbed for future exploration missions. This capability will provide significant cost savings by reducing the launch mass and volume required for printer feedstock as well as reduce waste that must be stored or disposed.

Asphalt recycling technology: Literature review and research plan

NASA Astrophysics Data System (ADS)

Newcomb, D. E.; Epps, J. A.

1981-06-01

A review of current technology for the rehabilitation and maintenance of pavement surfaces by recycling was conducted. While the primary concern was asphalt concrete recycling, a brief review of portland cement concrete recycling is included. Reports of cases involving recycling technology and lessons learned are reviewed. Recommendations are presented outlining research required to advance the state-of-the-art in a manner that will permit the U.S. Air Force to fully attain the benefits of recycling technology.

Sensor array for the detection of organic and inorganic contaminants in post-consumer recycled plastics for food contact.

PubMed

Davis, Nathan; Danes, Jeffrey E; Vorst, Keith

2017-10-01

Post-consumer recycled (PCR) plastic material is made by collecting used plastic products (e.g., bottles and other plastic packaging materials) and reprocessing them into solid-state pellets or flakes. Plastic recycling has positive environmental benefits, but may also carry potential drawbacks due to unwanted organic and inorganic contaminants. These contaminants can migrate into food packaging made from these recycled plastic materials. The purpose of this research was to identify economically viable real-time monitoring technologies that can be used during the conversion of virgin and recycled resin feedstocks (i.e., various blends of virgin pellets and recycled solid-state pellet or mechanically ground flake) to final articles to ensure the safety, quality and sustainability of packaging feedstocks. Baseline analysis (validation) of real-time technologies was conducted using industry-standard practices for polymer analysis. The data yielded supervised predictive models developed by training sessions completed in a controlled laboratory setting. This technology can be employed to evaluate compliance and aid converters in commodity sourcing of resin without exceeding regulatory thresholds. Furthermore, this technology allowed for real-time decision and diversion strategies during the conversion of resin and flake to final articles or products to minimise the negative impact on human health and environmental exposure.

Discovering Hidden Resources: Assistive Technology Recycling, Refurbishing, and Redistribution. RESNA Technical Assistance Project.

ERIC Educational Resources Information Center

RESNA: Association for the Advancement of Rehabilitation Technology, Arlington, VA.

This monograph discusses the benefits of recycling and reusing assistive technology for students with disabilities. It begins by discussing the benefits of recycled assistive technology for suppliers, students, and consumers, and then profiles programmatic models for assistive technology recycling programs. The advantages and disadvantages for…

Technology development for lunar base water recycling

NASA Technical Reports Server (NTRS)

Schultz, John R.; Sauer, Richard L.

1992-01-01

This paper will review previous and ongoing work in aerospace water recycling and identify research activities required to support development of a lunar base. The development of a water recycle system for use in the life support systems envisioned for a lunar base will require considerable research work. A review of previous work on aerospace water recycle systems indicates that more efficient physical and chemical processes are needed to reduce expendable and power requirements. Development work on biological processes that can be applied to microgravity and lunar environments also needs to be initiated. Biological processes are inherently more efficient than physical and chemical processes and may be used to minimize resupply and waste disposal requirements. Processes for recovering and recycling nutrients such as nitrogen, phosphorus, and sulfur also need to be developed to support plant growth units. The development of efficient water quality monitors to be used for process control and environmental monitoring also needs to be initiated.

End-of-Life Vehicle Dismantling and Recycling Enterprises: Developing Directions in China

NASA Astrophysics Data System (ADS)

Wang, Lu; Chen, Ming

2013-08-01

End-of-life vehicle (ELV) dismantling and recycling enterprises are the final disposer of the life-cycle process of vehicles. ELV collecting, dismantling technology, and waste disposal directly affect the recovery rate and the friendliness of vehicles toward the environment. China law stipulates that, by 2017, the recovery rate of vehicles should not be less than 95%, and the recycling rate of materials should not be less than 85%. Therefore, knowing the practical running state of such enterprises is needed. This study investigated four ELV dismantling and recycling enterprises in the Yangzi delta district in China and surveyed the ELV collecting, dismantling technology, policy implementation, and running difficulties. After the comparison with the developed countries, the relevant experiences were drawn, and effective measures were put forward to meet the aims stipulated in the law based on the current practical ELV market in China.

Wastewater recycling technology for fermentation in polyunsaturated fatty acid production.

PubMed

Song, Xiaojin; Ma, Zengxin; Tan, Yanzhen; Zhang, Huidan; Cui, Qiu

2017-07-01

To reduce fermentation-associated wastewater discharge and the cost of wastewater treatment, which further reduces the total cost of DHA and ARA production, this study first analyzed the composition of wastewater from Aurantiochytrium (DHA) and Mortierella alpina (ARA) fermentation, after which wastewater recycling technology for these fermentation processes was developed. No negative effects of DHA and ARA production were observed when the two fermentation wastewater methods were cross-recycled. DHA and ARA yields were significantly inhibited when the wastewater from the fermentation process was directly reused. In 5-L fed-batch fermentation experiments, using this cross-recycle technology, the DHA and ARA yields were 30.4 and 5.13gL -1 , respectively, with no significant changes (P>0.05) compared to the control group, and the water consumption was reduced by half compared to the traditional process. Therefore, this technology has great potential in industrial fermentation for polyunsaturated fatty acid production. Copyright © 2017 Elsevier Ltd. All rights reserved.

Recycling of waste lead storage battery by vacuum methods.

PubMed

Lin, Deqiang; Qiu, Keqiang

2011-07-01

Waste lead storage battery is the most important recyclable lead material not only in various European and other OECD countries but also in China. Pollution control of lead has become the focus of people's attention in the world. A vacuum process for recycling waste lead storage battery was developed in this work. The experimental results showed that all the valuable materials in waste lead storage battery could be satisfactorily recycled by vacuum technologies. The vacuum melting of lead grids and the vacuum reduction of lead pastes produce the lead bullion with the direct recovery ratio of 96.29% and 98.98%, respectively. The vacuum pyrolysis of plastics can produce pyrolysis oil with yield of more than 93 wt.%. These vacuum recycling technologies offer improvements in metallurgical and environmental performance. Copyright © 2011 Elsevier Ltd. All rights reserved.

Current and Prospective Li-Ion Battery Recycling and Recovery Processes

NASA Astrophysics Data System (ADS)

Heelan, Joseph; Gratz, Eric; Zheng, Zhangfeng; Wang, Qiang; Chen, Mengyuan; Apelian, Diran; Wang, Yan

2016-10-01

The lithium ion (Li-ion) battery industry has been growing exponentially since its initial inception in the late 20th century. As battery materials evolve, the applications for Li-ion batteries have become even more diverse. To date, the main source of Li-ion battery use varies from consumer portable electronics to electric/hybrid electric vehicles. However, even with the continued rise of Li-ion battery development and commercialization, the recycling industry is lagging; approximately 95% of Li-ion batteries are landfilled instead of recycled upon reaching end of life. Industrialized recycling processes are limited and only capable of recovering secondary raw materials, not suitable for direct reuse in new batteries. Most technologies are also reliant on high concentrations of cobalt to be profitable, and intense battery sortation is necessary prior to processing. For this reason, it is critical that a new recycling process be commercialized that is capable of recovering more valuable materials at a higher efficiency. A new technology has been developed by the researchers at Worcester Polytechnic Institute which is capable of recovering LiNi x Mn y Co z O2 cathode material from a hydrometallurgical process, making the recycling system as a whole more economically viable. By implementing a flexible recycling system that is closed-loop, recycling of Li-ion batteries will become more prevalent saving millions of pounds of batteries from entering the waste stream each year.

Sustainable recycling technologies for Solar PV off-grid system

NASA Astrophysics Data System (ADS)

Uppal, Bhavesh; Tamboli, Adish; Wubhayavedantapuram, Nandan

2017-11-01

Policy makers throughout the world have accepted climate change as a repercussion of fossil fuel exploitation. This has led the governments to integrate renewable energy streams in their national energy mix. PV off-grid Systems have been at the forefront of this transition because of their permanently increasing efficiency and cost effectiveness. These systems are expected to produce large amount of different waste streams at the end of their lifetime. It is important that these waste streams should be recycled because of the lack of available resources. Our study found that separate researches have been carried out to increase the efficiencies of recycling of individual PV system components but there is a lack of a comprehensive methodical research which details efficient and sustainable recycling processes for the entire PV off-grid system. This paper reviews the current and future recycling technologies for PV off-grid systems and presents a scheme of the most sustainable recycling technologies which have the potential for adoption. Full Recovery End-of-Life Photovoltaic (FRELP) recycling technology can offer opportunities to sustainably recycle crystalline silicon PV modules. Electro-hydrometallurgical process & Vacuum technologies can be used for recovering lead from lead acid batteries with a high recovery rate. The metals in the WEEE can be recycled by using a combination of biometallurgical technology, vacuum metallurgical technology and other advanced metallurgical technologies (utrasonical, mechano-chemical technology) while the plastic components can be effectively recycled without separation by using compatibilizers. All these advanced technologies when used in combination with each other provide sustainable recycling options for growing PV off-grid systems waste. These promising technologies still need further improvement and require proper integration techniques before implementation.

Comparative environmental and human health evaluations of thermolysis and solvolysis recycling technologies of carbon fiber reinforced polymer waste.

PubMed

Khalil, Y F

2018-06-01

This quantitative research aims to compare environmental and human health impacts associated with two recycling technologies of CFRP waste. The 'baseline' recycling technology is the conventional thermolysis process via pyrolysis and the 'alternative' recycling technology is an emerging chemical treatment via solvolysis using supercritical water (SCW) to digest the thermoset matrix. Two Gate-to-Gate recycling models are developed using GaBi LCA platform. The selected functional unit (FU) is 1 kg CFRP waste and the geographical boundary of this comparative LCIA is defined to be within the U.S. The results of this comparative assessment brought to light new insights about the environmental and human health impacts of CFRP waste recycling via solvolysis using SCW and, therefore, helped close a gap in the current state of knowledge about sustainability of SCW-based solvolysis as compared to pyrolysis. Two research questions are posed to identify whether solvolysis recycling offers more environmental and human health gains relative to the conventional pyrolysis recycling. These research questions lay the basis for formulating two null hypotheses (H 0,1 and H 0,2 ) and their associated research hypotheses (H 1,1 and H 1,2 ). LCIA results interpretation included 'base case' scenarios, 'sensitivity studies,' and 'scenarios analysis.' The results revealed that: (a) recycling via solvolysis using SCW exhibits no gains in environmental and human health impacts relative to those impacts associated with recycling via pyrolysis and (b) use of natural gas in lieu of electricity for pyrolyzer's heating reduces the environmental and human health impacts by 37% (lowest) and up to 95.7% (highest). It is recommended that on-going experimental efforts that focus only on identifying the best solvent for solvolysis-based recycling should also consider quantification of the energy intensity as well as environmental and human health impacts of the proposed solvents. Copyright © 2018 Elsevier Ltd. All rights reserved.

Innovative technologies of waste recycling with production of high performance products

NASA Astrophysics Data System (ADS)

Gilmanshin, R.; Ferenets, A. V.; Azimov, Yu I.; Galeeva, A. I.; Gilmanshina, S. I.

2015-06-01

The innovative ways of recycling wastes as a tool for sustainable development are presented in the article. The technology of the production of a composite material based on the rubber fiber composite waste tire industry is presented. The results of experimental use of the products in the real conditions. The comparative characteristics of the composite material rubber fiber composite are given. The production technology of construction and repairing materials on the basis of foamed glass is presented.

Development of rapid bioconversion with integrated recycle technology for ethanol production from extractive ammonia pretreated corn stover.

PubMed

Jin, Mingjie; Liu, Yanping; da Costa Sousa, Leonardo; Dale, Bruce E; Balan, Venkatesh

2017-08-01

High enzyme loading and low productivity are two major issues impeding low cost ethanol production from lignocellulosic biomass. This work applied rapid bioconversion with integrated recycle technology (RaBIT) and extractive ammonia (EA) pretreatment for conversion of corn stover (CS) to ethanol at high solids loading. Enzymes were recycled via recycling unhydrolyzed solids. Enzymatic hydrolysis with recycled enzymes and fermentation with recycled yeast cells were studied. Both enzymatic hydrolysis time and fermentation time were shortened to 24 h. Ethanol productivity was enhanced by two times and enzyme loading was reduced by 30%. Glucan and xylan conversions reached as high as 98% with an enzyme loading of as low as 8.4 mg protein per g glucan. The overall ethanol yield was 227 g ethanol/kg EA-CS (191 g ethanol/kg untreated CS). Biotechnol. Bioeng. 2017;114: 1713-1720. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

Integrated treatment and recycling of stormwater: a review of Australian practice.

PubMed

Hatt, Belinda E; Deletic, Ana; Fletcher, Tim D

2006-04-01

With the use of water approaching, and in some cases exceeding, the limits of sustainability in many locations, there is an increasing recognition of the need to utilise stormwater for non-potable requirements, thus reducing the demand on potable sources. This paper presents a review of Australian stormwater treatment and recycling practices as well as a discussion of key lessons and identified knowledge gaps. Where possible, recommendations for overcoming these knowledge gaps are given. The review of existing stormwater recycling systems focussed primarily on the recycling of general urban runoff (runoff generated from all urban surfaces) for non-potable purposes. Regulations and guidelines specific to stormwater recycling need to be developed to facilitate effective design of such systems, and to minimise risks of failure. There is a clear need for the development of innovative techniques for the collection, treatment and storage of stormwater. Existing stormwater recycling practice is far ahead of research, in that there are no technologies designed specifically for stormwater recycling. Instead, technologies designed for general stormwater pollution control are frequently utilised, which do not guarantee the necessary reliability of treatment. Performance modelling for evaluation purposes also needs further research, so that industry can objectively assess alternative approaches. Just as many aspects of these issues may have impeded adoption of stormwater, another impediment to adoption has been the lack of a practical and widely accepted method for assessing the many financial, social and ecological costs and benefits of stormwater recycling projects against traditional alternatives. Such triple-bottom-line assessment methodologies need to be trialled on stormwater recycling projects. If the costs and benefits of recycling systems can be shown to compare favourably with the costs and benefits of conventional practices this will provide an incentive to overcome other obstacles to widespread adoption of stormwater recycling.

The recycling dilemma for advanced materials use: Automobile materials substitution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Field, F.R. III; Clark, J.P.

1991-01-01

This paper discusses the difficulties associated with imposing recycling imperatives upon advanced materials development by examining the case of automotive materials substitution and its impacts upon the recyclability of the automobile. Parallels are drawn between today's issues, which focus upon the recyclability of the increasing polymeric fraction in automobile shredder fluff, and the junked automobile problem of the 1960's, when the problem of abandoned automobiles became a part of the environmental and legislative agenda in the US and overseas. In the 1960's, both the source and the resolution of the junk automobile problem arose through a confluence of technological andmore » economic factors, rather than through any set of regulatory influences. The rise of electric arc furnace steelmaking and the development of the automobile shredder were sufficient to virtually eliminate the problem - so much so that today's problems are incorrectly viewed as novelties. Today's automobile recycling problem again derives from technological and economic factors, but regulatory influences have spurred some of them. While there are no lack of technological solutions to the problem of automobile shredder fluff, none of these solutions yet provides scrap processors with the kind of profit opportunity necessary to implement them. In some ways, it is implicit in advanced materials markets that there is little to no demand for recycled forms of these materials, and, in the absence of these markets, there are few reasons to expect that the solution to today's problems will be quite so neat.« less

Polymer recycling: potential application of radiation technology

NASA Astrophysics Data System (ADS)

Burillo, Guillermina; Clough, Roger L.; Czvikovszky, Tibor; Guven, Olgun; Le Moel, Alain; Liu, Weiwei; Singh, Ajit; Yang, Jingtian; Zaharescu, Traian

2002-04-01

Management of solid waste is an important problem, which is becoming progressively worse as a byproduct of continuing economic growth and development. Polymeric materials (plastics and rubbers) comprise a steadily increasing proportion of the municipal and industrial waste going into landfill. Development of technologies for reducing polymeric waste, which are acceptable from the environmental standpoint, and which are cost-effective, has proven to be a difficult challenge due to complexities inherent in the reuse of polymers. Establishing optimal processes for the reuse/recycling of polymeric materials thus remains a worldwide challenge as we enter the new century. Due to the ability of ionizing radiation to alter the structure and properties of bulk polymeric materials, and the fact that it is applicable to essentially all polymer types, irradiation holds promise for impacting the polymer waste problem. The three main possibilities for use of radiation in this application are: (1) enhancing the mechanical properties and performance of recovered materials or material blends, principally through crosslinking, or through surface modification of different phases being combined; (2) treatment causing or enhancing the decomposition of polymers, particularly through chain scission, leading to recovery of either low molecular weight mixtures, or powders, for use as chemical feedstocks or additives; (3) production of advanced polymeric materials designed for environmental compatibility. This paper provides an overview of the polymer recycling problem, describes the major technological obstacles to the implementation of recycling technologies, and outlines some of the approaches being taken. A review of radiation-based recycling research is then provided, followed by a discussion of future directions where irradiation may be relevant to the problems currently inhibiting the widespread recycling of polymeric materials.

Challenges and Alternatives to Plastics Recycling in the Automotive Sector.

PubMed

Miller, Lindsay; Soulliere, Katie; Sawyer-Beaulieu, Susan; Tseng, Simon; Tam, Edwin

2014-08-15

Plastics are increasingly a preferred material choice in designing and developing complex, consumer products, such as automobiles, because they are mouldable, lightweight, and are often perceived to be highly recyclable materials. However, actually recycling the heterogeneous plastics used in such durable items is challenging, and presents very different scenarios to how simple products, such as water bottles, are recovered via curbside or container recycling initiatives. While the technology exists to recycle plastics, their feasibility to do so from high level consumer or industrial applications is bounded by technological and economical restraints. Obstacles include the lack of market for recyclates, and the lack of cost efficient recovery infrastructures or processes. Furthermore, there is a knowledge gap between manufacturers, consumers, and end-of-life facility operators. For these reasons, end-of-life plastics are more likely to end up down-cycled, or as shredder residue and then landfilled. This paper reviews these challenges and several alternatives to recycling plastics in order to broaden the mindset surrounding plastics recycling to improve their sustainability. The paper focuses on the automotive sector for examples, but discussion can be applied to a wide range of plastic components from similarly complex products.

Challenges and Alternatives to Plastics Recycling in the Automotive Sector

PubMed Central

Miller, Lindsay; Soulliere, Katie; Sawyer-Beaulieu, Susan; Tseng, Simon; Tam, Edwin

2014-01-01

Plastics are increasingly a preferred material choice in designing and developing complex, consumer products, such as automobiles, because they are mouldable, lightweight, and are often perceived to be highly recyclable materials. However, actually recycling the heterogeneous plastics used in such durable items is challenging, and presents very different scenarios to how simple products, such as water bottles, are recovered via curbside or container recycling initiatives. While the technology exists to recycle plastics, their feasibility to do so from high level consumer or industrial applications is bounded by technological and economical restraints. Obstacles include the lack of market for recyclates, and the lack of cost efficient recovery infrastructures or processes. Furthermore, there is a knowledge gap between manufacturers, consumers, and end-of-life facility operators. For these reasons, end-of-life plastics are more likely to end up down-cycled, or as shredder residue and then landfilled. This paper reviews these challenges and several alternatives to recycling plastics in order to broaden the mindset surrounding plastics recycling to improve their sustainability. The paper focuses on the automotive sector for examples, but discussion can be applied to a wide range of plastic components from similarly complex products. PMID:28788167

78 FR 14774 - U.S. Environmental Solutions Toolkit-Universal Waste

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-07

... following list: (a) Mercury Recycling Technology (b) E-Waste Recycling Technology (c) CRT Recycling Technology (d) Lamp Crushing Systems For purposes of participation in the Toolkit, ``United States exporter...

Sustainable waste management through end-of-waste criteria development.

PubMed

Zorpas, Antonis A

2016-04-01

The Waste Framework Directive 2000/98 (WFD) contains specific requirements to define end-of-waste criteria (EWC). The main goal of EWC is to remove and eliminate the administrative loads of waste legislation for safe and high-quality waste materials, thereby facilitating and assisting recycling. The target is to produce effective with high quality of recyclables materials, promoting product standardization and quality and safety assurance, and improving harmonization and legal certainty in the recyclable material markets. At the same time, those objectives aim to develop a plan in order to improve the development and wider use of environmental technologies, which reduce pressure on environment and at the same time address the three dimensions of the Lisbon strategy: growth, jobs and environment. This paper presents the importance of EWC, and the approach of setting EWC as EWC affect several management systems as well as sustainable and clean technologies.

Simple technology for recycling phosphate from wastewater to farmland in rural areas.

PubMed

Ohtake, Hisao; Okano, Kenji; Kunisada, Masashi; Takano, Hiroyuki; Toda, Masaya

2018-01-01

A simple technology for phosphate (P i ) recovery has been developed using a bifunctional adsorption-aggregation agent. The bifunctional agent was prepared by soaking calcium silicates in hydrochloric acid solution. Importantly, recyclable calcium silicates were available almost free of charge from the cement industry and also from the steel industry. The acid treatment was essential not only for enhancing the ability of calcium silicates to remove P i from aqueous solution but also for enabling the high settleability of removed P i . On-site experiments using a mobile plant showed that approximately 80% P i could be recovered from anaerobic sludge digestion liquor at a wastewater treatment plant. This technology has the potential to offer a simple, compact service for recycling P i from wastewater to farmland in rural areas.

Multi-material classification of dry recyclables from municipal solid waste based on thermal imaging.

PubMed

Gundupalli, Sathish Paulraj; Hait, Subrata; Thakur, Atul

2017-12-01

There has been a significant rise in municipal solid waste (MSW) generation in the last few decades due to rapid urbanization and industrialization. Due to the lack of source segregation practice, a need for automated segregation of recyclables from MSW exists in the developing countries. This paper reports a thermal imaging based system for classifying useful recyclables from simulated MSW sample. Experimental results have demonstrated the possibility to use thermal imaging technique for classification and a robotic system for sorting of recyclables in a single process step. The reported classification system yields an accuracy in the range of 85-96% and is comparable with the existing single-material recyclable classification techniques. We believe that the reported thermal imaging based system can emerge as a viable and inexpensive large-scale classification-cum-sorting technology in recycling plants for processing MSW in developing countries. Copyright © 2017 Elsevier Ltd. All rights reserved.

TECHNOLOGY EVALUATION REPORT: SITE PROGRAM DEMON- STRATION TEST - HORSEHEAD RESOURCE DEVELOPMENT COMPANY, INC. - FLAME REACTOR TECHNOLOGY - MONACA, PENNSYLVANIA

EPA Science Inventory

A SITE demonstration of the Horsehead Resource Development (HRD) Company, Inc. Flame Reactor Technology was conducted in March 1991 at the HRD facility in Monaca, Pennsylvania. or this demonstration, secondary lead smelter soda slag was treated to produce a potentially recyclable...

Recycling of polymers: a review.

PubMed

Ignatyev, Igor A; Thielemans, Wim; Vander Beke, Bob

2014-06-01

Plastics are inexpensive, easy to mold, and lightweight. These and many other advantages make them very promising candidates for commercial applications. In many areas, they have substantially suppressed traditional materials. However, the problem of recycling still is a major challenge. There are both technological and economic issues that restrain the progress in this field. Herein, a state-of-art overview of recycling is provided together with an outlook for the future by using popular polymers such as polyolefins, poly(vinyl chloride), polyurethane, and poly(ethylene terephthalate) as examples. Different types of recycling, primary, secondary, tertiary, quaternary, and biological recycling, are discussed together with related issues, such as compatibilization and cross-linking. There are various projects in the European Union on research and application of these recycling approaches; selected examples are provided in this article. Their progress is mirrored by granted patents, most of which have a very limited scope and narrowly cover certain technologies. Global introduction of waste utilization techniques to the polymer market is currently not fully developed, but has an enormous potential. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

CONTINUOUS MICRO-SORTING OF COMPLEX WASTE PLASTICS PARTICLEMIXTURES VIA LIQUID-FLUIDIZED BED CLASSIFICATION (LFBC) FOR WASTE MINIMIZATIONAND RECYCLING

EPA Science Inventory

A fundamental investigation is proposed to provide a technical basis for the development of a novel, liquid-fluidized bed classification (LFBC) technology for the continuous separation of complex waste plastic mixtures for in-process recycling and waste minimization. Although ...

Plastic flexible films waste management - A state of art review.

PubMed

Horodytska, O; Valdés, F J; Fullana, A

2018-04-21

Plastic flexible films are increasingly used in many applications due to their lightness and versatility. In 2014, the amount of plastic films represented 34% of total plastic packaging produced in UK. The flexible film waste generation rises according to the increase in number of applications. Currently, in developed countries, about 50% of plastics in domestic waste are films. Moreover, about 615,000 tonnes of agricultural flexible waste are generated in the EU every year. A review of plastic films recycling has been conducted in order to detect the shortcomings and establish guidelines for future research. This paper reviews plastic films waste management technologies from two different sources: post-industrial and post-consumer. Clean and homogeneous post-industrial waste is recycled through closed-loop or open-loop mechanical processes. The main differences between these methods are the quality and the application of the recycled materials. Further research should be focused on closing the loops to obtain the highest environmental benefits of recycling. This could be accomplished through minimizing the material degradation during mechanical processes. Regarding post-consumer waste, flexible films from agricultural and packaging sectors have been assessed. The agricultural films and commercial and industrial flexible packaging are recycled through open-loop mechanical recycling due to existing selective waste collection routes. Nevertheless, the contamination from the use phase adversely affects the quality of recycled plastics. Therefore, upgrading of current washing lines is required. On the other hand, household flexible packaging shows the lowest recycling rates mainly because of inefficient sorting technologies. Delamination and compatibilization methods should be further developed to ensure the recycling of multilayer films. Finally, Life Cycle Assessment (LCA) studies on waste management have been reviewed. A lack of thorough LCA on plastic films waste management systems was identified. Copyright © 2018 Elsevier Ltd. All rights reserved.

Waste management of printed wiring boards: a life cycle assessment of the metals recycling chain from liberation through refining.

PubMed

Xue, Mianqiang; Kendall, Alissa; Xu, Zhenming; Schoenung, Julie M

2015-01-20

Due to economic and societal reasons, informal activities including open burning, backyard recycling, and landfill are still the prevailing methods used for electronic waste treatment in developing countries. Great efforts have been made, especially in China, to promote formal approaches for electronic waste management by enacting laws, developing green recycling technologies, initiating pilot programs, etc. The formal recycling process can, however, engender environmental impact and resource consumption, although information on the environmental loads and resource consumption is currently limited. To quantitatively assess the environmental impact of the processes in a formal printed wiring board (PWB) recycling chain, life cycle assessment (LCA) was applied to a formal recycling chain that includes the steps from waste liberation through materials refining. The metal leaching in the refining stage was identified as a critical process, posing most of the environmental impact in the recycling chain. Global warming potential was the most significant environmental impact category after normalization and weighting, followed by fossil abiotic depletion potential, and marine aquatic eco-toxicity potential. Scenario modeling results showed that variations in the power source and chemical reagents consumption had the greatest influence on the environmental performance. The environmental impact from transportation used for PWB collection was also evaluated. The results were further compared to conventional primary metals production processes, highlighting the environmental benefit of metal recycling from waste PWBs. Optimizing the collection mode, increasing the precious metals recovery efficiency in the beneficiation stage and decreasing the chemical reagents consumption in the refining stage by effective materials liberation and separation are proposed as potential improvement strategies to make the recycling chain more environmentally friendly. The LCA results provide environmental information for the improvement of future integrated technologies and electronic waste management.

Phonon Recycling for Ultrasensitive Kinetic Inductance Detectors

NASA Astrophysics Data System (ADS)

Zmuidzinas, Jonas

Initially proposed (Day et al. 2003; Zmuidzinas 2012) in 1999 by our Caltech/JPL group, and thanks to strong support from NASA, the superconducting (microwave) kinetic inductance detector (MKID or KID) technology continues to develop rapidly as it transitions into applications. The development effort worldwide is intensifying and NASA's continued support of KID development is essential in order to keep pace. Here we propose to investigate and demonstrate a new, low-TRL concept, which we call phonon recycling, that promises to open broad new avenues in KID design and performance. Briefly, phonon recycling allows the detector designer to tailor the responsivity and sensitivity of a KID to match the needs of the application by using geometry to restrict the rate at which recombination phonons are allowed to escape from the detector. In particular, phonon recycling should allow very low noise-equivalent power (NEP) to be achieved without requiring very low operating tem- peratures. Phonon recycling is analogous to the use of micromachined suspension legs to control the flow of heat in a bolometer, as measured by the thermal conductivity G. However, phonon recycling exploits the non-thermal distribution of recombination phonons as well as their very slow decay in crystals at low temperatures. These properties translate to geometrical and mechanical requirements for a phonon-recycled KID that are considerably more relaxed than for a bolometer operating at the same temperature and NEP. Our ultimate goal is to develop detector arrays suitable for a far-infrared (FIR) space mission, which will impose strict requirements on the array sensitivity, yield, uniformity, multiplexing density, etc. Through previous NASA support under the Strategic Astrophysics Technology (SAT) program, we have successfully demonstrated the MAKO submillimeter camera at the Caltech Submillimeter Observatory and have become familiar with these practical issues. If our demonstration of phonon recycling is successful, we will have a path for continuously adapting the high-background, high-NEP detectors we have demonstrated on the ground to the ultralow-NEP detectors needed for space.

Evaluating waste printed circuit boards recycling: Opportunities and challenges, a mini review.

PubMed

Awasthi, Abhishek Kumar; Zlamparet, Gabriel Ionut; Zeng, Xianlai; Li, Jinhui

2017-04-01

Rapid generation of waste printed circuit boards has become a very serious issue worldwide. Numerous techniques have been developed in the last decade to resolve the pollution from waste printed circuit boards, and also recover valuable metals from the waste printed circuit boards stream on a large-scale. However, these techniques have their own certain specific drawbacks that need to be rectified properly. In this review article, these recycling technologies are evaluated based on a strength, weaknesses, opportunities and threats analysis. Furthermore, it is warranted that, the substantial research is required to improve the current technologies for waste printed circuit boards recycling in the outlook of large-scale applications.

Application of NIR hyperspectral imaging for post-consumer polyolefins recycling

NASA Astrophysics Data System (ADS)

Serranti, Silvia; Gargiulo, Aldo; Bonifazi, Giuseppe

2012-06-01

An efficient large-scale recycling approach of particulate solid wastes is always accomplished according to the quality of the materials fed to the recycling plant and/or to any possible continuous and reliable control of the different streams inside the processing plants. Processing technologies addressed to recover plastics need to be extremely powerful, since they must be relatively simple to be cost-effective, but also accurate enough to create high-purity products and able to valorize a substantial fraction of the plastic waste materials into useful products of consistent quality in order to be economical. On the other hand, the potential market for such technologies is large and the boost of environmental regulations, and the oil price increase, has made many industries interested both in "general purpose" waste sorting technologies, as well as in developing more specialized sensing devices and/or inspection logics for a better quality assessment of plastic products. In this perspective recycling strategies have to be developed taking into account some specific aspects as i) mixtures complexity: the valuable material has to be extracted from the residue, ii) overall production: the profitability of plastic can be achieved only with mass production and iii) costs: low-cost sorting processes are required. In this paper new analytical strategies, based on hyperspectral imaging in the near infrared field (1000-1700 nm), have been investigated and set up in order to define sorting and/or quality control logics that could be profitably applied, at industrial plant level, for polyolefins recycling.

Central sorting and recovery of MSW recyclable materials: A review of technological state-of-the-art, cases, practice and implications for materials recycling.

PubMed

Cimpan, Ciprian; Maul, Anja; Jansen, Michael; Pretz, Thomas; Wenzel, Henrik

2015-06-01

Today's waste regulation in the EU comprises stringent material recovery targets and calls for comprehensive programs in order to achieve them. A similar movement is seen in the US where more and more states and communities commit to high diversion rates from landfills. The present paper reviews scientific literature, case studies and results from pilot projects, on the topic of central sorting of recyclable materials commonly found in waste from households. The study contributes, inter alia, with background understanding on the development of materials recovery, both in a historical and geographical perspective. Physical processing and sorting technology has reached a high level of maturity, and many quality issues linked to cross-contamination by commingling have been successfully addressed to date. New sorting plants tend to benefit from economies of scale, and innovations in automation and process control, which are targeted at curtailing process inefficiencies shown by operational practice. Technology developed for the sorting of commingled recyclables from separate collection is also being successfully used to upgrade residual MSW processing plants. The strongest motivation for central sorting of residual MSW is found for areas where source separation and separate collection is difficult, such as urban agglomerations, and can in such areas contribute to increasing recycling rates, either complementary to- or as a substitute for source separation of certain materials, such as plastics and metals. Copyright © 2015 Elsevier Ltd. All rights reserved.

Efficient One-Step Electrolytic Recycling of Low-Grade and Post-Consumer Magnesium Scrap

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adam C. Powell, IV

2012-07-19

Metal Oxygen Separation Technologies, Inc. (abbreviated MOxST, pronounced most) and Boston University (BU) have developed a new low-cost process for recycling post-consumer co-mingled and heavily-oxidized magnesium scrap, and discovered a new chemical mechanism for magnesium separations in the process. The new process, designated MagReGenTM, is very effective in laboratory experiments, and on scale-up promises to be the lowest-cost lowest-energy lowest-impact method for separating magnesium metal from aluminum while recovering oxidized magnesium. MagReGenTM uses as little as one-eighth as much energy as today's methods for recycling magnesium metal from comingled scrap. As such, this technology could play a vital role inmore » recycling automotive non-ferrous metals, particularly as motor vehicle magnesium/aluminum ratios increase in order to reduce vehicle weight and increase efficiency.« less

Genetic incorporation of recycled unnatural amino acids.

PubMed

Ko, Wooseok; Kim, Sanggil; Jo, Kyubong; Lee, Hyun Soo

2016-02-01

The genetic incorporation of unnatural amino acids (UAAs) into proteins has been a useful tool for protein engineering. However, most UAAs are expensive, and the method requires a high concentration of UAAs, which has been a drawback of the technology, especially for large-scale applications. To address this problem, a method to recycle cultured UAAs was developed. The method is based on recycling a culture medium containing the UAA, in which some of essential nutrients were resupplemented after each culture cycle, and induction of protein expression was controlled with glucose. Under optimal conditions, five UAAs were recycled for up to seven rounds of expression without a decrease in expression level, cell density, or incorporation fidelity. This method can generally be applied to other UAAs; therefore, it is useful for reducing the cost of UAAs for genetic incorporation and helpful for expanding the use of the technology to industrial applications.

Annual patents review, January-December 2004

Treesearch

Roland Gleisner; Karen Scallon; Michael Fleischmann; Julie Blankenburg; Marguerite Sykes

2005-01-01

This review summarizes patents related to paper recycling that first appeared in patent databases during the 2004. Two on-line databases, Claims/U.S. Patents Abstracts and Derwent World Patents Index, were searched for this review. This feature is intended to inform readers about recent developments in equipment design, chemicals, and process technologies for recycling...

End-of-life vehicle recycling : state of the art of resource recovery from shredder residue.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jody, B. J.; Daniels, E. J.; Duranceau, C. M.

Each year, more than 25 million vehicles reach the end of their service life throughout the world, and this number is rising rapidly because the number of vehicles on the roads is rapidly increasing. In the United States, more than 95% of the 10-15 million scrapped vehicles annually enter a comprehensive recycling infrastructure that includes auto parts recyclers/dismantlers, remanufacturers, and material recyclers (shredders). Today, over 75% of automotive materials, primarily the metals, are profitably recycled via (1) parts reuse and parts and components remanufacturing and (2) ultimately by the scrap processing (shredding) industry. The process by which the scrap processorsmore » recover metal scrap from automobiles involves shredding the obsolete automobile hulks, along with other obsolete metal-containing products (such as white goods, industrial scrap, and demolition debris), and recovering the metals from the shredded material. The single largest source of recycled ferrous scrap for the iron and steel industry is obsolete automobiles. The non-metallic fraction that remains after the metals are recovered from the shredded materials - commonly called shredder residue - constitutes about 25% of the weight of the vehicle, and it is disposed of in landfills. This practice is not environmentally friendly, wastes valuable resources, and may become uneconomical. Therefore, it is not sustainable. Over the past 15-20 years, a significant amount of research and development has been undertaken to enhance the recycle rate of end-of-life vehicles, including enhancing dismantling techniques and improving remanufacturing operations. However, most of the effort has been focused on developing technology to separate and recover non-metallic materials, such as polymers, from shredder residue. To make future vehicles more energy efficient, more lightweighting materials - primarily polymers, polymer composites, high-strength steels, and aluminum - will be used in manufacturing these vehicles. Many of these materials increase the percentage of shredder residue that must be disposed of, compared with the percentage of metals that are recovered. In addition, the number of hybrid vehicles and electric vehicles on the road is rapidly increasing. This trend will also introduce new materials for disposal at the end of their useful lives, including batteries. Therefore, as the complexity of automotive materials and systems increases, new technologies will be required to sustain and maximize the ultimate recycling of these materials and systems. Argonne National Laboratory (Argonne), the Vehicle Recycling Partnership, LLC. (VRP) of the United States Council for Automotive Research, LLC. (USCAR), and the American Chemistry Council-Plastics Division (ACC-PD) are working to develop technology for recovering materials from end-of-life vehicles, including separating and recovering polymers and residual metals from shredder residue. Several other organizations worldwide are also working on developing technology for recycling materials from shredder residue. Without a commercially viable shredder industry, our nation and the world will most likely face greater environmental challenges and a decreased supply of quality scrap, and thereby be forced to turn to primary ores for the production of finished metals. This will result in increased energy consumption and increased damage to the environment, including increased greenhouse gas emissions. The recycling of polymers, other organics, and residual metals in shredder residue saves the equivalent of over 23 million barrels of oil annually. This results in a 12-million-ton reduction in greenhouse gas emissions. This document presents a review of the state-of-the-art in the recycling of automotive materials.« less

Recycling of non-metallic fractions from waste electrical and electronic equipment (WEEE): A review

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Ruixue; Xu, Zhenming, E-mail: zmxu@sjtu.edu.cn

Highlights: • NMFs from WEEE were treated by incineration or land filling in the past. • Environmental risks such as heavy metals and BFRs will be the major problems during the NMFs recycling processes. • Methods and technologies of recycling the two types of NMFs from WEEE, plastics, glasses are reviewed. • More environmental impact assessment should be carried out to evaluate the environmental risks of the recycling products. - Abstract: The world’s waste electrical and electronic equipment (WEEE) consumption has increased incredibly in recent decades, which have drawn much attention from the public. However, the major economic driving forcemore » for recycling of WEEE is the value of the metallic fractions (MFs). The non-metallic fractions (NMFs), which take up a large proportion of E-wastes, were treated by incineration or landfill in the past. NMFs from WEEE contain heavy metals, brominated flame retardant (BFRs) and other toxic and hazardous substances. Combustion as well as landfill may cause serious environmental problems. Therefore, research on resource reutilization and safe disposal of the NMFs from WEEE has a great significance from the viewpoint of environmental protection. Among the enormous variety of NMFs from WEEE, some of them are quite easy to recycle while others are difficult, such as plastics, glass and NMFs from waste printed circuit boards (WPCBs). In this paper, we mainly focus on the intractable NMFs from WEEE. Methods and technologies of recycling the two types of NMFs from WEEE, plastics, glass are reviewed in this paper. For WEEE plastics, the pyrolysis technology has the lowest energy consumption and the pyrolysis oil could be obtained, but the containing of BFRs makes the pyrolysis recycling process problematic. Supercritical fluids (SCF) and gasification technology have a potentially smaller environmental impact than pyrolysis process, but the energy consumption is higher. With regard to WEEE glass, lead removing is requisite before the reutilization of the cathode ray tube (CRT) funnel glass, and the recycling of liquid crystal display (LCD) glass is economically viable for the containing of precious metals (indium and tin). However, the environmental assessment of the recycling process is essential and important before the industrialized production stage. For example, noise and dust should be evaluated during the glass cutting process. This study could contribute significantly to understanding the recycling methods of NMFs from WEEE and serve as guidance for the future technology research and development.« less

Effective Technology for Recycling Metal. Proceedings of Two Special Workshops.

ERIC Educational Resources Information Center

National Association of Secondary Material Industries, Inc., New York, NY.

The National Association of Secondary Material Industries (NASMI) and the Bureau of Mines have cooperated to sponsor two technically-oriented workshops related to the role of metals recycling and air pollution control technology. The proceedings of these workshops, "Effective Technology and Research for Scrap Metal Recycling" and "Air Pollution…

An evaluation of the potential yield of indium recycled from end-of-life LCDs: A case study in China.

PubMed

Wang, Hengguang; Gu, Yifan; Wu, Yufeng; Zhang, Yi-Nan; Wang, Wei

2015-12-01

With the advances in electronics and information technology, China has gradually become the largest consumer of household appliances (HAs). Increasingly, end-of-life (EOL) HAs are generated in China. EOL recycling is a promising strategy to reduce dependence on virgin production, and indium is one of the recycled substances. The potential yield of indium recycling has not been systematically evaluated in China thus far. This paper estimates the potential yield of recycled indium from waste liquid crystal displays (LCDs) in China during the period from 2015 to 2030. The quantities of indium that will be used to produce LCDs are also predicted. The estimates focus on the following three key LCD waste sources: LCD TVs, desktop computers and portable computers. The results show that the demand for indium will be increasing in the near future. It is expected that 350 tonnes of indium will be needed to produce LCDs in China in 2035. The indium recycled from EOL LCDs, however, is much less than the demand and only accounts for approximately 48% of the indium demand. The sustainable index of indium is always less than 0.5. Therefore, future indium recycling efforts should focus on the development of recycling technology and the improvement of the relevant policy. Copyright © 2015 Elsevier Ltd. All rights reserved.

Gene modification of the acetate biosynthesis pathway in Escherichia coli and implementation of the cell recycling technology to increase L-tryptophan production

PubMed Central

Bai, Fang; Chen, Ning; Bai, Gang

2017-01-01

The implementation of a novel cell recycling technology based on a special disk centrifuge during microbial fermentation process can continuously separate the product and harmful intermediates, while maintaining the cell viability owing to the installed cooling system. Acetate accumulation is an often encountered problem in L-tryptophan fermentation by Escherichia coli. To extend our previous studies, the current study deleted the key genes underlying acetate biosynthesis to improve l-tryptophan production. The deletion of the phosphotransacetylase (pta)–acetate kinase (ackA) pathway in a gltB (encoding glutamate synthase) mutant of E. coli TRTHB, led to the highest production of l-tryptophan (47.18 g/L) and glucose conversion rate (17.83%), with a marked reduction in acetate accumulation (1.22 g/L). This strain, TRTHBPA, was then used to investigate the effects of the cell recycling process on L-tryptophan fermentation. Four different strategies were developed concerning two issues, the volume ratio of the concentrated cell solution and clear solution and the cell recycling period. With strategy I (concentrated cell solution: clear solution, 1: 1; cell recycling within 24–30 h), L-tryptophan production and the glucose conversion rate increased to 55.12 g/L and 19.75%, respectively, 17.55% and 10.77% higher than those without the cell recycling. In addition, the biomass increased by 13.52% and the fermentation period was shortened from 40 h to 32 h. These results indicated that the cell recycling technology significantly improved L-tryptophan production by E. coli. PMID:28622378

Demonstration of Advanced Technologies for Multi-Load Washers in Hospitality and Healthcare -- Wastewater Recycling Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boyd, Brian K.; Parker, Graham B.; Petersen, Joseph M.

The objective of this demonstration project was to evaluate market-ready retrofit technologies for reducing the energy and water use of multi-load washers in healthcare and hospitality facilities. Specifically, this project evaluated laundry wastewater recycling technology in the hospitality sector and ozone laundry technology in both the healthcare and hospitality sectors. This report documents the demonstration of a wastewater recycling system installed in the Grand Hyatt Seattle.

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

The Lightweight Materials activity (LM) within the Vehicle Technologies Program focuses on the development and validation of advanced materials and manufacturing technologies to significantly reduce light and heavy duty vehicle weight without compromising other attributes such as safety, performance, recyclability, and cost.

Semiannual patents review, July-December 1998

Treesearch

Matthew Stroika; Marguerite Sykes; Julie Blankenburg

1999-01-01

This review summarizes patents related to paper recycling issued during the last 6 months of 1998. The two online databases used for this search are Claim/US. Patents Abstracts and Derwent World Patents Index. This semiannual feature is intended to inform readers about the latest developments in equipment, chemicals, and technology in the field of paper recycling. This...

Recycled plastics: On-line exchange may breathe life into market

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stringer, J.

1995-11-15

While plastics recycling has become more technologically developed during the past few years, the market-made up of a large number of small companies and municipalities-still remains plagued by unorganized pricing and lack of standardized quality. However, industry players are hoping the recently launched Chicago Board of Trade (CBOT) Recyclable Exchange will put new life into the market by establishing industry-wide standards and making the market more efficient. While many are watching the project with {open_quotes}cautious optimism,{close_quotes} the goal is to match up suppliers with buyers and make recyclable trading easier and cheaper, especially for smaller companies.

Multiobjective optimization of hybrid regenerative life support technologies. Topic D: Technology Assessment

NASA Technical Reports Server (NTRS)

Manousiouthakis, Vasilios

1995-01-01

We developed simple mathematical models for many of the technologies constituting the water reclamation system in a space station. These models were employed for subsystem optimization and for the evaluation of the performance of individual water reclamation technologies, by quantifying their operational 'cost' as a linear function of weight, volume, and power consumption. Then we performed preliminary investigations on the performance improvements attainable by simple hybrid systems involving parallel combinations of technologies. We are developing a software tool for synthesizing a hybrid water recovery system (WRS) for long term space missions. As conceptual framework, we are employing the state space approach. Given a number of available technologies and the mission specifications, the state space approach would help design flowsheets featuring optimal process configurations, including those that feature stream connections in parallel, series, or recycles. We visualize this software tool to function as follows: given the mission duration, the crew size, water quality specifications, and the cost coefficients, the software will synthesize a water recovery system for the space station. It should require minimal user intervention. The following tasks need to be solved for achieving this goal: (1) formulate a problem statement that will be used to evaluate the advantages of a hybrid WRS over a single technology WBS; (2) model several WRS technologies that can be employed in the space station; (3) propose a recycling network design methodology (since the WRS synthesis task is a recycling network design problem, it is essential to employ a systematic method in synthesizing this network); (4) develop a software implementation for this design methodology, design a hybrid system using this software, and compare the resulting WRS with a base-case WRS; and (5) create a user-friendly interface for this software tool.

Bioregenerative life support: not a picnic

NASA Technical Reports Server (NTRS)

Knott, W. M.

1998-01-01

If humans are to live permanently in space, regenerative life support systems are an enabling technology and must replace the picnic approach of taking all supplies required for each mission. These systems are classified by technologies as either physical/chemical or bioregenerative. Both of these system-types can recycle water, remove carbon dioxide, produce oxygen, and recover essential elements from waste products. Bioregenerative can also produce food, thus, making it essential if humans are to exist in space independent of earth. A solely bioregenerative life support system includes plants as a biomass production module and microbial organisms in bioreactors as a resource recovery module. In the Advanced Life Support Program, bioregenerative life support systems are being investigated through a research and technology development project which includes large scale testing as part of the Breadboard Project and human tests conducted in the soon to be constructed BioPlex facility. Research and technology development efforts are directed toward optimizing biomass productivity in controlled chambers by developing light weight, energy efficient, and automated systems; recycling liquid and solid wastes; baselining the operation of bioreactors; determining system microbial stability; assessing chemical contamination; and building models required for long term system operations. The program will include space flight studies in the near future to determine if these life support technologies will function in microgravity. When a bioregenerative system is finally incorporated into a mission, the conversion from a picnic and resupply mentality to permanent recycling and independence from earth will be complete.

Recent development of recycling lead from scrap CRTs: A technological review.

PubMed

Yu-Gong; Tian, Xiang-Miao; Wu, Yu-Feng; Zhe-Tan; Lei-Lv

2016-11-01

Cathode ray tubes (CRTs) contain numerous harmful substances with different functions. Lead is found in the funnel glass of CRTs. Improperly treated toxic lead may pose significant risks to human health and the environment. This paper reviews and summarizes existing technological processes on the recycling of lead from waste CRTs, including pyrometallurgy, hydrometallurgy, and product-regeneration. The present situation, advantages, and disadvantages of these techniques are described in detail. Generally, pyrometallurgy shows better practicability in recovery lead from waste CRT than hydrometallurgy and hydrometallurgy, in view of environmental impact, energy-consumption, product formats and safety and maturity of technology. Moreover, the gaps in the existing technologies were identified and recommendations for future research were provided. Copyright © 2015 Elsevier Ltd. All rights reserved.

Advanced reactors and associated fuel cycle facilities: safety and environmental impacts.

PubMed

Hill, R N; Nutt, W M; Laidler, J J

2011-01-01

The safety and environmental impacts of new technology and fuel cycle approaches being considered in current U.S. nuclear research programs are contrasted to conventional technology options in this paper. Two advanced reactor technologies, the sodium-cooled fast reactor (SFR) and the very high temperature gas-cooled reactor (VHTR), are being developed. In general, the new reactor technologies exploit inherent features for enhanced safety performance. A key distinction of advanced fuel cycles is spent fuel recycle facilities and new waste forms. In this paper, the performance of existing fuel cycle facilities and applicable regulatory limits are reviewed. Technology options to improve recycle efficiency, restrict emissions, and/or improve safety are identified. For a closed fuel cycle, potential benefits in waste management are significant, and key waste form technology alternatives are described. Copyright © 2010 Health Physics Society

INNOVATIVE TECHNOLOGY FOR RECYCLING OF MANURE PHOSPHORUS WITH RAPID AMORPHOUS PHOSPHATE PRECIPITATION

EPA Science Inventory

Phosphorus (P) recovery from liquid swine manure is an attractive technology when soils in the farm are saturated with P and on-farm land application is not an option. A technology was developed for recovery of soluble P from liquid swine manure as amorphous calcium phosphate (AC...

Cryo-comminution of plastic waste.

PubMed

Gente, Vincenzo; La Marca, Floriana; Lucci, Federica; Massacci, Paolo; Pani, Eleonora

2004-01-01

Recycling of plastics is a big issue in terms of environmental sustainability and of waste management. The development of proper technologies for plastic recycling is recognised as a priority. To achieve this aim, the technologies applied in mineral processing can be adapted to recycling systems. In particular, the improvement of comminution technologies is one of the main actions to improve the quality of recycled plastics. The aim of this work is to point out suitable comminution processes for different types of plastic waste. Laboratory comminution tests have been carried out under different conditions of temperature and sample pre-conditioning adopting as refrigerant agents CO2 and liquid nitrogen. The temperature has been monitored by thermocouples placed in the milling chamber. Also different internal mill screens have been adopted. A proper procedure has been set up in order to obtain a selective comminution and a size reduction suitable for further separation treatment. Tests have been performed on plastics coming from medical plastic waste and from a plant for spent lead batteries recycling. Results coming from different mill devices have been compared taking into consideration different indexes for representative size distributions. The results of the performed tests show as cryo-comminution improves the effectiveness of size reduction of plastics, promotes liberation of constituents and increases specific surface size of comminuted particles in comparison to a comminution process carried out at room temperature. Copyright 2004 Elsevier Ltd.

Case study: apparel industry waste management: a focus on recycling in South Africa.

PubMed

Larney, M; van Aardt, A M

2010-01-01

The need for effective apparel waste management is motivated by the increasing cost and decreasing availability of landfill space and the dwindling of natural resources. The aim of this study was to identify the current solid waste disposal and recycling practices of the apparel industry in South Africa and to determine their attitude and willingness towards recycling, their perception of the feasibility thereof, barriers to recycling and marketing strategies that would be appropriate for products made from recycled materials. A structured questionnaire was mailed to apparel manufacturers in South Africa. The results indicated that most apparel manufacturers use landfills to dispose of their waste, while approximately half recycle some of the waste. They are fairly positive towards recycling, with consideration of economical feasibility. Phi-coefficients show no practically significant relationship between company size and the use of recycled materials. The most important barriers to recycling are lack of equipment and technology, lack of material to recycle and lack of consumer awareness. Marketing strategies for recycled products are recommended. It is concluded that consumer awareness and knowledge regarding recycled apparel products should be developed in order to ensure a market and that apparel manufacturers should be encouraged to recycle more extensively, in order to ensure that resources will not be exhausted unnecessarily and the environment will be preserved optimally.

Recycling of non-metallic fractions from waste electrical and electronic equipment (WEEE): a review.

PubMed

Wang, Ruixue; Xu, Zhenming

2014-08-01

The world's waste electrical and electronic equipment (WEEE) consumption has increased incredibly in recent decades, which have drawn much attention from the public. However, the major economic driving force for recycling of WEEE is the value of the metallic fractions (MFs). The non-metallic fractions (NMFs), which take up a large proportion of E-wastes, were treated by incineration or landfill in the past. NMFs from WEEE contain heavy metals, brominated flame retardant (BFRs) and other toxic and hazardous substances. Combustion as well as landfill may cause serious environmental problems. Therefore, research on resource reutilization and safe disposal of the NMFs from WEEE has a great significance from the viewpoint of environmental protection. Among the enormous variety of NMFs from WEEE, some of them are quite easy to recycle while others are difficult, such as plastics, glass and NMFs from waste printed circuit boards (WPCBs). In this paper, we mainly focus on the intractable NMFs from WEEE. Methods and technologies of recycling the two types of NMFs from WEEE, plastics, glass are reviewed in this paper. For WEEE plastics, the pyrolysis technology has the lowest energy consumption and the pyrolysis oil could be obtained, but the containing of BFRs makes the pyrolysis recycling process problematic. Supercritical fluids (SCF) and gasification technology have a potentially smaller environmental impact than pyrolysis process, but the energy consumption is higher. With regard to WEEE glass, lead removing is requisite before the reutilization of the cathode ray tube (CRT) funnel glass, and the recycling of liquid crystal display (LCD) glass is economically viable for the containing of precious metals (indium and tin). However, the environmental assessment of the recycling process is essential and important before the industrialized production stage. For example, noise and dust should be evaluated during the glass cutting process. This study could contribute significantly to understanding the recycling methods of NMFs from WEEE and serve as guidance for the future technology research and development. Copyright © 2014 Elsevier Ltd. All rights reserved.

TECHNOLOGY EVALUATION REPORT: TORONTO HARBOUR COMMISSIONERS (THC) SOIL RECYCLE TREATMENT TRAIN. Project Summary

EPA Science Inventory

A demonstration of the Toronto Harbour Commissioners' (THC) Soil Recycle Treatment Train was performed under the Superfund Innovative Technology Evaluation (SITE) Program at a pilot plant facility in Toronto, Ontario, Canada. The Soil Recycle Treatment Train, which consists of s...

Recycling process for recovery of gallium from GaN an e-waste of LED industry through ball milling, annealing and leaching.

PubMed

Swain, Basudev; Mishra, Chinmayee; Kang, Leeseung; Park, Kyung-Soo; Lee, Chan Gi; Hong, Hyun Seon

2015-04-01

Waste dust generated during manufacturing of LED contains significant amounts of gallium and indium, needs suitable treatment and can be an important resource for recovery. The LED industry waste dust contains primarily gallium as GaN. Leaching followed by purification technology is the green and clean technology. To develop treatment and recycling technology of these GaN bearing e-waste, leaching is the primary stage. In our current investigation possible process for treatment and quantitative leaching of gallium and indium from the GaN bearing e-waste or waste of LED industry dust has been developed. To recycle the waste and quantitative leaching of gallium, two different process flow sheets have been proposed. In one, process first the GaN of the waste the LED industry dust was leached at the optimum condition. Subsequently, the leach residue was mixed with Na2CO3, ball milled followed by annealing, again leached to recover gallium. In the second process, the waste LED industry dust was mixed with Na2CO3, after ball milling and annealing, followed acidic leaching. Without pretreatment, the gallium leaching was only 4.91 w/w % using 4M HCl, 100°C and pulp density of 20g/L. After mechano-chemical processing, both these processes achieved 73.68 w/w % of gallium leaching at their optimum condition. The developed process can treat and recycle any e-waste containing GaN through ball milling, annealing and leaching. Copyright © 2015 Elsevier Inc. All rights reserved.

Chapter 24. emerging technologies for irrigation water treatment

USDA-ARS?s Scientific Manuscript database

Several disinfestants that have potential for treating recycled irrigation water are less commonly used or newer developing technologies. Hydrogen peroxide can reduce spread of pathogens in water that contains nutrients or pesticide residues without generating toxic residues. Benefits potentially in...

Chemical recycling of scrap composites

NASA Technical Reports Server (NTRS)

Allred, Ronald E.; Salas, Richard M.

1994-01-01

There are no well-developed technologies for recycling composite materials other than grinding to produce fillers. New approaches are needed to reclaim these valuable resources. Chemical or tertiary recycling, conversion of polymers into low molecular weight hydrocarbons for reuse as chemicals or fuels, is emerging as the most practical means for obtaining value from waste plastics and composites. Adherent Technologies is exploring a low-temperature catalytic process for recycling plastics and composites. Laboratory results show that all types of plastics, thermosets as well as thermoplastics, can be converted in high yields to valuable hydrocarbon products. This novel catalytic process runs at 200 C, conversion times are rapid, the process is closed and, thus, nonpolluting, and no highly toxic gas or liquid products have been observed so no negative environmental impact will result from its implementation. Tests on reclamation of composite materials show that epoxy, imide, and engineering thermoplastic matrices can be converted to low molecular weight hydrocarbons leaving behind the reinforcing fibers for reuse as composite reinforcements in secondary, lower-performance applications. Chemical recycling is also a means to dispose of sensitive or classified organic materials without incineration and provides a means to eliminate or reduce mixed hazardous wastes containing organic materials.

Improvement of logistics education from the point of view environmental management

NASA Astrophysics Data System (ADS)

Bányai, Á.

2009-04-01

The paper briefly presents the influence of environmental management on the improvement of the logistics education and research structure of the Department of Materials Handling and Logistics at the University of Miskolc, Hungary. The logistics, as an integrated science offers a very good possibility to demonstrate the effect of new innovative knowledge on the migration of the priorities of education and research of sciences. The importance of logistics in the field of recycling (or in wider sense in the field of environmental management) can be justified by the high proportion of logistic costs (as investment and operation costs) and these costs show that optimum logistic solutions are able to decrease the financial outcomes and lead to the establishment of a profitable system. Technological change constantly creates new demands on both education and research. The most important objective of the department is to create a unique logistics education in the country. For this reason the department offered up-to-date integrated knowledge at all level: undergraduate, master degree and PhD education. The integration of logistics means traditionally the joint use of technology of material handling, method of material flow, technology method of traffic, information technology, management sciences, production technology, marketing, market research, technology of services, mathematics and optimization, communication technology, system engineering, electronics and automation, mechatronics [1, 3]. The education and research portfolio of the department followed this tradition till 1993. The new lectures in the field of sustainability (logistics of recycling, logistics of quality management and recycling, closed loop economy, EU logistics or global logistics) became more and more important in the logistics education. The results of fast developments in closed loop economy, recycling, waste management, environmental protection are more and more used in the industry and this effected a revolutionary change in the education and research structure of logistics [2]. The European Community policy in the environment sectors aims at a high level of protection. Four principles were defined: the precautionary principle, the principle that preventive action should be taken, that environmental damages should as a priority be rectified at source and that the polluter should pay. All of these four principles have a very strong logistics background, especially in the field of import/export operations, traffic/transportation, inventory control, materials handling, fleet operations, customer service, supply chain management, distribution, strategic planning, warehousing, information systems of logistics, purchasing. These facts effect the development of different topics of logistics in each field of the education of the department: collection logistics of used products (especially WEEE), optimization of collection systems, design and control of disassembly systems, distribution of fractions of disassembled used products, design and control of recycling parks, possibilities of virtual networks in the field of recycling logistics, integration of logistics, recycling and total quality management, identification systems and recycling, etc. Within the framework of different supports our department has the opportunity to take part in European networks and research projects in the field of sustainability, environmental protection, recycling and closed loop economy. One of the biggest networks was developed within the framework of a Brite-Euram project entitled ‘Closing the loop from the product design to the end of life technologies'. The importance of logistics is certified by the fact, that this network defined the milestones of the improvement of an economically beneficial closed loop economy as quality aspects, communication and marketing, logistics and qualification. Within the frame of this project the logistics focused on the improvement of technologies (disassembly, reuse, refurbishment, remanufacturing and recycling), collection systems, and development of the concept for collection logistics and pre-disassembly, market survey in waste management. The Regional Knowledge Centre of Mechatronics and Logistics Systems was established in 2005. The overall objective of Knowledge Centre is to develop knowledge-intensive mechatronics and logistics systems in the leading edge of the world and to integrate the results in the economy and society through utilising the knowledge. The realisation of the objective requires the establishment and operation of a networking system of relations between those involved in sciences, the economy and society. The knowledge centre is a "knowledge integration tool" of the university in the field of mechanical engineering, and plays an important part in the intensification of the integration of the philosophy of sustainability into the related sciences. The program of the knowledge centre is focused on three well definable strategic fields, which are the vertical elements of the model. These are the R&D programs: world of products, materials and technologies, and integrated systems. The programs cover the implementation of seven, internationally competitive, application-oriented part tasks. These seven part tasks and the sustainability are closely related. The realisation of the part tasks through networking offers considerable results and economical-ecological benefits, forth for the participants and the region. The activities include basic and applied research, experimental development, technology transfer, as well as education and training and preparing the new scientific generation. The horizontal elements of the model are given by the utilisation of knowledge that can be interpreted in different dimensions: technical/engineering, legal, sustainability, economic, and social. The program relies on the continuation of existing relations in networks, and its regional nature is embodied in the cooperation of the higher education institutes and companies of the three counties. This publication was supported by the National Office for Research and Technology within the frame of Pázmány Péter programme. Any opinions, findings and conclusions or recommendations expressed in this material are those of the author and do not necessarily reflect the views of the National Office for Research and Technology. Literature: [1] J. Cselényi, Gy. Fischer, J. Murvai, B. Mang: Typical models of the recycling logistics of worn out product. Proceedings of XIV. International Conference on Material Handling and Warehousing in Belgrade, 1996. pp. 138-143. [2] R. Knoth, M. Hoffmann, B. Kopacek, P. Kopacek: A logistic concept to improve the re-usability of electric and electronic equipment, Electronics and the Environment, 2001. Proceedings of the 2001 IEEE International Symposium. 2001. pp. 115 - 118. [3] L. Cser, B. Mang: Cleaner Technologies and Recycling in Hungary. Proceedings of Int. Workshop on Environmental Conscious Manufacturing in Hertogenbosch, The Netherlands, 1997. pp. 48-56.

Recycling research progress at the Forest Products Laboratory.

Treesearch

1995-01-01

This document summarizes accomplishments of USDA Forest Service researchers in the area of recycling. Specifically, it describes work in economic assessment, paper recycling, recycled housing and industrial applications of recycled materials, other recycling applications, and technology transfer. The literature list includes the references cited in the text and...

Model institutional infrastructures for recycling of photovoltaic modules

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reaven, S.J.; Moskowitz, P.D.; Fthenakis, V.

1996-01-01

How will photovoltaic modules (PVMS) be recycled at the end of their service lives? This question has technological and institutional components (Reaven, 1994a). The technological aspect concerns the physical means of recycling: what advantages and disadvantages of the several existing and emerging mechanical, thermal, and chemical recycling processes and facilities merit consideration? The institutional dimension refers to the arrangements for recycling: what are the operational and financial roles of the parties with an interest in PVM recycling? These parties include PVM manufacturers, trade organizations; distributors, and retailers; residential, commercial, and utility PVM users; waste collectors, transporters, reclaimers, and reclaimers; andmore » governments.« less

New technology recipes include horseradish, vinegar, mushrooms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bishop, J.

1995-08-01

Technology development for more effective environmental management continues to abound. This article contains some recent innovations in the following areas: wastewater treatment; site remediation; and air pollution control. In addition several emerging technologies address solid and hazardous waste management with techniques designed to reduce waste volume, recycle valuable materials and create new energy sources.

Development of Solvent Extraction Approach to Recycle Enriched Molybdenum Material

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tkac, Peter; Brown, M. Alex; Sen, Sujat

2016-06-01

Argonne National Laboratory, in cooperation with Oak Ridge National Laboratory and NorthStar Medical Technologies, LLC, is developing a recycling process for a solution containing valuable Mo-100 or Mo-98 enriched material. Previously, Argonne had developed a recycle process using a precipitation technique. However, this process is labor intensive and can lead to production of large volumes of highly corrosive waste. This report discusses an alternative process to recover enriched Mo in the form of ammonium heptamolybdate by using solvent extraction. Small-scale experiments determined the optimal conditions for effective extraction of high Mo concentrations. Methods were developed for removal of ammonium chloridemore » from the molybdenum product of the solvent extraction process. In large-scale experiments, very good purification from potassium and other elements was observed with very high recovery yields (~98%).« less

Advanced Life Support Water Recycling Technologies Case Studies: Vapor Phase Catalytic Ammonia Removal and Direct Osmotic Concentration

NASA Technical Reports Server (NTRS)

Flynn, Michael

2004-01-01

Design for microgravity has traditionally not been well integrated early on into the development of advanced life support (ALS) technologies. NASA currently has a many ALS technologies that are currently being developed to high technology readiness levels but have not been formally evaluated for microgravity compatibility. Two examples of such technologies are the Vapor Phase Catalytic Ammonia Removal Technology and the Direct Osmotic Concentration Technology. This presentation will cover the design of theses two systems and will identify potential microgravity issues.

Recycling

NASA Astrophysics Data System (ADS)

Goto, Junya; Santorelli, Michael

Recycling systems are classified into those employing typically three methods, and the progress of each method is described. In mechanical recycling, powders of phenolic materials are recovered via a mechanical process and reused as fillers or additives in virgin materials. The effects to flowability, curability, and mechanical properties of the materials are explained. In feedstock recycling, monomers, oligomers, or oils are recovered via chemical processes and reused as feedstock. Pyrolysis, solvolysis or hydrolysis, and supercritical or subcritical fluid technology will also be introduced. When using a subcritical fluid of phenol, the recycled material maintains excellent properties similar to the virgin material, and a demonstration plant has been constructed to carry out mass production development. In energy recovery, wastes of phenolic materials are used as an alternative solid fuel to coal because they are combustible and have good calorific value. Industrial wastes of these have been in practical use in a cement plant. Finally, it is suggested that the best recycling method should be selected according to the purpose or situation, because every recycling method has both strengths and weaknesses. Therefore, quantitative and objective evaluation methods in recycling are desirable and should be established.

Wealth generation through recycling of material for reuse

NASA Astrophysics Data System (ADS)

Chukwudum, Okechukw John; Patience I., E.

2018-06-01

Management of solid waste needs appropriate technology, which is economically affordable, socially accepted and environmentally friendly. The public needs to be sensitized on the potential wealth that their inorganic and organic wastes contain. The paper deals with the idea of recycling as a means of solid waste treatment and explores. In developing countries, where standards are often lower and raw materials very expensive, there is a wider scope for use of recycled material. The range of products varies from building materials to shoes, home to office equipment, sewage pipe to beauty aids. Recyclingand reuse issues overlap a range of disciplines.

78 FR 75293 - Approval and Promulgation of Implementation Plans; State of California; 2012 Los Angeles County...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-11

... Angeles County are two large lead-acid battery recycling facilities, Exide Technologies located in the... two large lead-acid battery-recycling facilities--Exide Technologies in Vernon (``Exide'') and... battery recycling facilities (i.e., Exide and Quemetco) as the only sources of lead in the Los Angeles...

Environmental friendly crush-magnetic separation technology for recycling metal-plated plastics from end-of-life vehicles.

PubMed

Xue, Mianqiang; Li, Jia; Xu, Zhenming

2012-03-06

Metal-plated plastics (MPP), which are important from the standpoint of aesthetics or even performance, are increasingly employed in a wide variety of situations in the automotive industry. Serious environmental problems will be caused if they are not treated appropriately. Therefore, recycling of MPP is an important subject not only for resource recycling but also for environmental protection. This work represents a novel attempt to deal with the MPP. A self-designed hammer crusher was used to liberate coatings from the plastic substrate. The size distribution of particles was analyzed and described by the Rosin-Rammler function model. The optimum retaining time of materials in the crusher is 3 min. By this time, the liberation rate of the materials can reach 87.3%. When the density of the suspension is 31,250 g/m(3), the performance of liberation is the best. Two-step magnetic separation was adopted to avoid excessive crushing and to guarantee the quality of products. Concerning both the separation efficiency and grade of products, the optimum rotational speed of the magnetic separator is 50-70 rpm. On the basis of the above studies about the liberating and separating behavior of the materials, a continuous recycling system (the technology of crush-magnetic separation) is developed. This recycling system provides a feasible method for recycling MPP efficiently, economically, and environmentally.

Maisotsenko cycle applications in multi-stage ejector recycling module for chemical production

NASA Astrophysics Data System (ADS)

Levchenko, D. O.; Artyukhov, A. E.; Yurko, I. V.

2017-08-01

The article is devoted to the theoretical bases of multistage (multi-level) utilization modules as part of chemical plants (on the example of the technological line for obtaining nitrogen fertilizers). The possibility of recycling production waste (ammonia vapors, dust and substandard nitrogen fertilizers) using ejection devices and waste heat using Maisotsenko cycle technology (Maisotsenko heat and mass exchanger (HMX), Maisotsenko power cycles and recuperators, etc.) is substantiated. The principle of operation of studied recycling module and prospects for its implementation are presented. An improved technological scheme for obtaining granular fertilizers and granules with porous structure with multistage (multi-level) recycling module is proposed.

Novel concept of recycling sludge and dust to BOF converter through dispersed in-situ phase induced by composite ball explosive reaction

NASA Astrophysics Data System (ADS)

Tang, Fu-ping; Yu, Shu-juan; Fei, Peng; Hou, Hou-yu; Qian, Feng; Wang, Xiao-feng

2017-08-01

Recycling of iron and steelmaking dusts is a key issue in environmental protection efforts and to ensure efficient utilization. In this investigation, we developed a novel recovery process that uses a dispersed in-situ phase induced by an explosive reaction of composite balls of iron and steelmaking dusts. We designed and prepared composite balls for this function using a laboratory model batch-type balling disc (at 12 r/min) and optimized the feeding modes in 180-t and 260-t basic oxygen furnace (BOF) converters. The results indicate that feeding composite balls into BOF converters is an effective novel technology for recovering iron and steelmaking dusts. The period after hot metal charging and prior to the oxygen-blowing process is the most reasonable time to feed composite balls. Composite ball treatment is not appropriate for steel production with sulfur requirements lower than 80 ppm. The maximum composite ball feeding amount is 40 kg/t and the iron yield rate is better than 95%. Compared with the conventional recycling process of sludge and dust, this novel technology is more convenient and efficient, saving up to 309 RMB per ton of steel. Further investigation of this novel recycling technology is merited.

Development of the Technologies for Stabilization Treatment of the Water of the Recycling Cooling Systems at Thermal Power Plants

NASA Astrophysics Data System (ADS)

Vlasov, S. M.; Chichirova, N. D.; Chichirov, A. A.; Vlasova, A. Yu.; Filimonova, A. A.; Prosvirnina, D. V.

2018-02-01

A turbine-condensate cooling system is one of the less stable and most hard-to-control systems of maintaining optimal water chemistry. A laboratory recycling cooling water test facility, UVO-0.3, was developed for physical simulation of innovative zero-discharge water chemistry conditions and improvement of technological flowcharts of stabilization treatment of the initial and circulating water of the recycling cooling systems at thermal power plants. Experiments were conducted in the UVO-0.3 facility to investigate the processes that occur in the recycling water supply system and master new technologies of stabilization of the initial and circulating water. It is shown that, when using untreated initial water, scaling cannot be prevented even under low concentration levels. The main reason for the activation of scale depositing is the desorption of carbon dioxide that results in alkalization of the circulating water and, as a consequence, a displacement of the chemical reaction equilibrium towards the formation of slightly soluble hardness ions. Some techniques, viz., liming and alkalization of the initial water and the by-pass treatment of the circulating water, are considered. New engineering solutions have been developed for reducing the amount of scale-forming substances in the initial and circulating water. The best results were obtained by pretreating the initial water with alkalizing agents and simultaneously bypassing and treating part of the circulating water. The obtained experimental data underlie the process flowcharts of stabilization treatment of the initial and circulating TPP water that ensure scale-free and noncorrosive operation and meet the corresponding environmental requirements. Under the bypassing, the specific rates of the agents and the residual hardness are reduced compared with the conventional pretreatment.

MOBILE ON-SITE RECYCLING OF METALWORKING FLUIDS

EPA Science Inventory

This evaluation addresses the product quality, waste reduction, and economic issues involved in recycling metalworking fluids through a mobile recycling unit. The specific recycling unit evaluated is based on the technology of filtration, pasteurization, and centrifugation. Metal...

Addressing Criticality in Rare Earth Elements via Permanent Magnets Recycling

NASA Astrophysics Data System (ADS)

Nlebedim, I. C.; King, A. H.

2017-12-01

Rare earth elements (REEs) are critical for many advanced technologies and are faced with potential supply disruptions. Recycling of permanent magnets (PMs) can be good sources for REEs which can help minimize global dependence on freshly mined REEs, but PMs are rarely recycled. Recycling of PMs has been discussed with respect to improving REEs resource sustainability. Some challenges to be addressed in order to establish industrially deployable technologies for PMs recycling have also been discussed, including profitability, energy efficiency and environmental impacts. Key considerations for promoting circular economy via PMs recycling is proposed with the focus on deciding the target points in the supply chain at which the recycled products will be inserted. Important technical considerations for recycling different forms of waste PMs, including swarfs, slags, shredded and intact hard disk drives magnets, have been presented. The aspects of circular economy considered include reusing magnets, remanufacturing magnets and recovering of REEs from waste PMs.

Addressing Criticality in Rare Earth Elements via Permanent Magnets Recycling

NASA Astrophysics Data System (ADS)

Nlebedim, I. C.; King, A. H.

2018-02-01

Rare earth elements (REEs) are critical for many advanced technologies and are faced with potential supply disruptions. Recycling of permanent magnets (PMs) can be good sources for REEs which can help minimize global dependence on freshly mined REEs, but PMs are rarely recycled. Recycling of PMs has been discussed with respect to improving REEs resource sustainability. Some challenges to be addressed in order to establish industrially deployable technologies for PMs recycling have also been discussed, including profitability, energy efficiency and environmental impacts. Key considerations for promoting circular economy via PMs recycling is proposed with the focus on deciding the target points in the supply chain at which the recycled products will be inserted. Important technical considerations for recycling different forms of waste PMs, including swarfs, slags, shredded and intact hard disk drives magnets, have been presented. The aspects of circular economy considered include reusing magnets, remanufacturing magnets and recovering of REEs from waste PMs.

Education & Collection Facility GSHP Demonstration Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Joplin, Jeff

The Denver Museum of Nature & Science (DMNS) designed and implemented an innovative ground source heat pump (GSHP) system for heating and cooling its new Education and Collection Facility (ECF) building addition. The project goal was to successfully design and install an open-loop GSHP system that utilized water circulating within an underground municipal recycled (non-potable) water system as the heat sink/source as a demonstration project. The expected results were to significantly reduce traditional GSHP installation costs while increasing system efficiency, reduce building energy consumption, require significantly less area and capital to install, and be economically implemented wherever access to amore » recycled water system is available. The project added to the understanding of GSHP technology by implementing the first GSHP system in the United States utilizing a municipal recycled water system as a heat sink/source. The use of this fluid through a GSHP system has not been previously documented. This use application presents a new opportunity for local municipalities to develop and expand the use of underground municipal recycled (non-potable) water systems. The installation costs for this type of technology in the building structure would be a cost savings over traditional GSHP costs, provided the local municipal infrastructure was developed. Additionally, the GSHP system functions as a viable method of heat sink/source as the thermal characteristics of the fluid are generally consistent throughout the year and are efficiently exchanged through the GSHP system and its components. The use of the recycled water system reduces the area required for bore or loop fields; therefore, presenting an application for building structures that have little to no available land use or access. This GSHP application demonstrates the viability of underground municipal recycled (non-potable) water systems as technically achievable, environmentally supportive, and an efficient system.« less

Recycling high-performance carbon fiber reinforced polymer composites using sub-critical and supercritical water

NASA Astrophysics Data System (ADS)

Knight, Chase C.

Carbon fiber reinforced plastics (CFRP) are composite materials that consist of carbon fibers embedded in a polymer matrix, a combination that yields materials with properties exceeding the individual properties of each component. CFRP have several advantages over metals: they offer superior strength to weight ratios and superior resistance to corrosion and chemical attack. These advantages, along with continuing improvement in manufacturing processes, have resulted in rapid growth in the number of CFRP products and applications especially in the aerospace/aviation, wind energy, automotive, and sporting goods industries. Due to theses well-documented benefits and advancements in manufacturing capabilities, CFRP will continue to replace traditional materials of construction throughout several industries. However, some of the same properties that make CFRP outstanding materials also pose a major problem once these materials reach the end of service life. They become difficult to recycle. With composite consumption in North America growing by almost 5 times the rate of the US GDP in 2012, this lack of recyclability is a growing concern. As consumption increases, more waste will inevitably be generated. Current composite recycling technologies include mechanical recycling, thermal processing, and chemical processing. The major challenge of CFRP recycling is the ability to recover materials of high-value and preserve their properties. To this end, the most suitable technology is chemical processing, where the polymer matrix can be broken down and removed from the fiber, with limited damage to the fibers. This can be achieved using high concentration acids, but such a process is undesirable due to the toxicity of such materials. A viable alternative to acid is water in the sub-critical and supercritical region. Under these conditions, the behavior of this abundant and most environmentally friendly solvent resembles that of an organic compound, facilitating the breakdown of the polymer matrix. To date, very few studies have been reported in this area and the studies thus far have only focused on small scale feasibility and have only shown the recovery of random fibers. The goal of this research is to advance the knowledge in the field of sub-critical and supercritical fluid recycling by providing fundamental information that will be necessary to move this process forward to an industrial scale. This dissertation work consists of several phases of studies. In the first phase of this research, the feasibility of recycling woven CFRP was established on a scale approximately 30 times larger than previously reported. The industrial relevance was also conveyed, as the process was shown to remove up 99% of a highly cross-linked resin from an aerospace grade composite system with 100% retention of the single filament tensile strength and modulus whilst also retaining the highly valuable woven fiber structure. The second phase of research demonstrated the power of this technology to recycle multi-layer composites and provide the ability to reuse the highly valuable materials. Up to 99% resin elimination was achieved for a woven 12-layer aerospace grade composite. The recycled woven fabric layers, with excellent retention of the fiber architecture, were directly reused to fabricate reclaimed fiber composites (RFC). Manufacturing issues associated with the use of the recycled fiber were investigated. Several fabrication technologies were used to fabricate the composite, and the composites show moderate short beam shear strength and may be suitable for certain industrial applications. Moreover, fresh composites were also recycled, recovered, and reused to investigate the retention of flexural properties of the fibers after recycling. Up to 95% of the flexural strength and 98% of the flexural modulus was retained in the reclaimed fiber composites. The recycled resin residual can be incorporated into fresh resin and cured, demonstrating a near complete recycling loop. After showing the feasibility and power of this technology, the third phase of the study was focused on the fundamentals on the degradation of highly cross-linked polymer network by sub- and near-critical water. A methodology framework was established to study the apparent kinetics of the degradation of epoxy in sub-critical water. The reaction rate was modeled by a phenomenological rate model of nth order, and the rate constant was modeled by taking into account of the contributions of important physical parameters, e.g., pressure, temperature and dielectric constants. The applicability of the established model to describe the degradation kinetics was confirmed by the validation runs. This model is a suitable starting point to gain the knowledge required for eventual industrial process design. The final phase of this research consisted of a preliminary foray into investigating the economic feasibility of this technology. A process model was designed around a reactor which was sized according to considerations of industrial relevancy. The simulation of the process was done using Aspen Plus, powerful and comprehensive process simulation software. Economic analysis of this pseudo-realistic process suggested that such technology was economically viable and competitive comparing to other recycling technologies. In summary, this dissertation work represents the first comprehensive investigation on recycling aerospace-grade, multilayer woven fabric composites using supercritical and sub-critical water. The fundamental knowledge gained and process technology developed during this research is anticipated to play an important role in advancing this recycling technology toward potential adoption and implementation by the recycling and composite industry.

Recycling process for recovery of gallium from GaN an e-waste of LED industry through ball milling, annealing and leaching

DOE Office of Scientific and Technical Information (OSTI.GOV)

Swain, Basudev, E-mail: swain@iae.re.kr; Mishra, Chinmayee; Kang, Leeseung

Waste dust generated during manufacturing of LED contains significant amounts of gallium and indium, needs suitable treatment and can be an important resource for recovery. The LED industry waste dust contains primarily gallium as GaN. Leaching followed by purification technology is the green and clean technology. To develop treatment and recycling technology of these GaN bearing e-waste, leaching is the primary stage. In our current investigation possible process for treatment and quantitative leaching of gallium and indium from the GaN bearing e-waste or waste of LED industry dust has been developed. To recycle the waste and quantitative leaching of gallium,more » two different process flow sheets have been proposed. In one, process first the GaN of the waste the LED industry dust was leached at the optimum condition. Subsequently, the leach residue was mixed with Na{sub 2}CO{sub 3}, ball milled followed by annealing, again leached to recover gallium. In the second process, the waste LED industry dust was mixed with Na{sub 2}CO{sub 3}, after ball milling and annealing, followed acidic leaching. Without pretreatment, the gallium leaching was only 4.91 w/w % using 4 M HCl, 100 °C and pulp density of 20 g/L. After mechano-chemical processing, both these processes achieved 73.68 w/w % of gallium leaching at their optimum condition. The developed process can treat and recycle any e-waste containing GaN through ball milling, annealing and leaching. - Highlights: • Simplest process for treatment of GaN an LED industry waste developed. • The process developed recovers gallium from waste LED waste dust. • Thermal analysis and phase properties of GaN to Ga{sub 2}O{sub 3} and GaN to NaGaO{sub 2} revealed. • Solid-state chemistry involved in this process reported. • Quantitative leaching of the GaN was achieved.« less

High-Tech, Low-Temp Insulation

NASA Technical Reports Server (NTRS)

1998-01-01

Under an SBIR (Small Business Innovative Research) contract with Ames, S.D. Miller & Associates developed new manufacturing methods for multi-layer metal spacecraft insulation that could significantly reduce launch weight and launch costs. The new honeycomb structure is more efficient than fibers for insulation. Honeycombs can be made from metals for high temperature uses, even plastic insulation from recycled milk bottles. Under development are blankets made from recycled milk bottles which will be field tested by the Red Cross and ambulance companies. Currently available are honeycomb mittens based on the same technology.

Waste printed circuit board recycling techniques and product utilization.

PubMed

Hadi, Pejman; Xu, Meng; Lin, Carol S K; Hui, Chi-Wai; McKay, Gordon

2015-01-01

E-waste, in particular waste PCBs, represents a rapidly growing disposal problem worldwide. The vast diversity of highly toxic materials for landfill disposal and the potential of heavy metal vapors and brominated dioxin emissions in the case of incineration render these two waste management technologies inappropriate. Also, the shipment of these toxic wastes to certain areas of the world for eco-unfriendly "recycling" has recently generated a major public outcry. Consequently, waste PCB recycling should be adopted by the environmental communities as an ultimate goal. This article reviews the recent trends and developments in PCB waste recycling techniques, including both physical and chemical recycling. It is concluded that the physical recycling techniques, which efficiently separate the metallic and nonmetallic fractions of waste PCBs, offer the most promising gateways for the environmentally-benign recycling of this waste. Moreover, although the reclaimed metallic fraction has gained more attention due to its high value, the application of the nonmetallic fraction has been neglected in most cases. Hence, several proposed applications of this fraction have been comprehensively examined. Copyright © 2014 Elsevier B.V. All rights reserved.

Presidential Green Chemistry Challenge: 2006 Small Business Award

EPA Pesticide Factsheets

Presidential Green Chemistry Challenge 2006 award winners, Arkon Consultants and NuPro Technologies, developed a safer processing system for flexographic printing that includes washout solvents and reclamation/recycling.

Waste recycling issues in bioregenerative life support

NASA Technical Reports Server (NTRS)

Macelroy, R. D.; Wang, D.

1989-01-01

Research and technology development issues centering on the recycling of materials within a bioregenerative life support system are reviewed. The importance of recovering waste materials for subsequent use is emphasized. Such material reclamation will substantially decrease the energy penalty paid for bioregenerative life support systems, and can potentially decrease the size of the system and its power demands by a significant amount. Reclamation of fixed nitrogen and the sugars in cellulosic materials is discussed.

Recent progress on preparation and properties of nanocomposites from recycled polymers: a review.

PubMed

Zare, Yasser

2013-03-01

Currently, the growing consumption of polymer products creates the large quantities of waste materials resulting in public concern in the environment and people life. Nanotechnology is assumed the important technology in the current century. Recently, many researchers have tried to develop this new science for polymer recycling. In this article, the application of different nanofillers in the recycled polymers such as PET, PP, HDPE, PVC, etc. and the attributed composites and blends is studied. The morphological, mechanical, rheological and thermal properties of prepared nanocomposites as well as the future challenges are extensively discussed. The present article determines the current status of nanotechnology in the polymer recycling which guide the future studies in this attractive field. Copyright © 2012 Elsevier Ltd. All rights reserved.

MOEX: Solvent extraction approach for recycling enriched 98Mo/ 100Mo material

DOE PAGES

Tkac, Peter; Brown, M. Alex; Momen, Abdul; ...

2017-03-20

Several promising pathways exist for the production of 99Mo/ 99mTc using enriched 98Mo or 100Mo. Use of Mo targets require a major change in current generator technology, and the necessity for an efficient recycle pathway to recover valuable enriched Mo material. High recovery yields, purity, suitable chemical form and particle size are required. Results on the development of the MOEX– molybdenum solvent extraction – approach to recycle enriched Mo material are presented. Furthermore, the advantages of the MOEX process are very high decontamination factors from potassium and other elements, high throughput, easy scalability, automation, and minimal waste generation.

MOEX: Solvent extraction approach for recycling enriched 98Mo/ 100Mo material

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tkac, Peter; Brown, M. Alex; Momen, Abdul

Several promising pathways exist for the production of 99Mo/ 99mTc using enriched 98Mo or 100Mo. Use of Mo targets require a major change in current generator technology, and the necessity for an efficient recycle pathway to recover valuable enriched Mo material. High recovery yields, purity, suitable chemical form and particle size are required. Results on the development of the MOEX– molybdenum solvent extraction – approach to recycle enriched Mo material are presented. Furthermore, the advantages of the MOEX process are very high decontamination factors from potassium and other elements, high throughput, easy scalability, automation, and minimal waste generation.

Presidential Green Chemistry Challenge: 2004 Greener Reaction Conditions Award

EPA Pesticide Factsheets

Presidential Green Chemistry Challenge 2004 award winner, Buckman Laboratories International, developed Optimyze technology, which uses an esterase enzyme to remove sticky contaminants from paper products prior to recycling.

Analysis of the Lifecycle of Mechanical Engineering Products

NASA Astrophysics Data System (ADS)

Gubaydulina, R. H.; Gruby, S. V.; Davlatov, G. D.

2016-08-01

Principal phases of the lifecycle of mechanical engineering products are analyzed in the paper. The authors have developed methods and procedures to improve designing, manufacturing, operating and recycling of the machine. It has been revealed that economic lifecycle of the product is a base for appropriate organization of mechanical engineering production. This lifecycle is calculated as a minimal sum total of consumer and producer costs. The machine construction and its manufacturing technology are interrelated through a maximal possible company profit. The products are to be recycled by their producer. Recycling should be considered as a feedback phase, necessary to make the whole lifecycle of the product a constantly functioning self-organizing system. The principles, outlined in this paper can be used as fundamentals to develop an automated PLM-system.

Sensitivity Analysis and Optimization of the Nuclear Fuel Cycle: A Systematic Approach

NASA Astrophysics Data System (ADS)

Passerini, Stefano

For decades, nuclear energy development was based on the expectation that recycling of the fissionable materials in the used fuel from today's light water reactors into advanced (fast) reactors would be implemented as soon as technically feasible in order to extend the nuclear fuel resources. More recently, arguments have been made for deployment of fast reactors in order to reduce the amount of higher actinides, hence the longevity of radioactivity, in the materials destined to a geologic repository. The cost of the fast reactors, together with concerns about the proliferation of the technology of extraction of plutonium from used LWR fuel as well as the large investments in construction of reprocessing facilities have been the basis for arguments to defer the introduction of recycling technologies in many countries including the US. In this thesis, the impacts of alternative reactor technologies on the fuel cycle are assessed. Additionally, metrics to characterize the fuel cycles and systematic approaches to using them to optimize the fuel cycle are presented. The fuel cycle options of the 2010 MIT fuel cycle study are re-examined in light of the expected slower rate of growth in nuclear energy today, using the CAFCA (Code for Advanced Fuel Cycle Analysis). The Once Through Cycle (OTC) is considered as the base-line case, while advanced technologies with fuel recycling characterize the alternative fuel cycle options available in the future. The options include limited recycling in L WRs and full recycling in fast reactors and in high conversion LWRs. Fast reactor technologies studied include both oxide and metal fueled reactors. Additional fuel cycle scenarios presented for the first time in this work assume the deployment of innovative recycling reactor technologies such as the Reduced Moderation Boiling Water Reactors and Uranium-235 initiated Fast Reactors. A sensitivity study focused on system and technology parameters of interest has been conducted to test the robustness of the conclusions presented in the MIT Fuel Cycle Study. These conclusions are found to still hold, even when considering alternative technologies and different sets of simulation assumptions. Additionally, a first of a kind optimization scheme for the nuclear fuel cycle analysis is proposed and the applications of such an optimization are discussed. Optimization metrics of interest for different stakeholders in the fuel cycle (economics, fuel resource utilization, high level waste, transuranics/proliferation management, and environmental impact) are utilized for two different optimization techniques: a linear one and a stochastic one. Stakeholder elicitation provided sets of relative weights for the identified metrics appropriate to each stakeholder group, which were then successfully used to arrive at optimum fuel cycle configurations for recycling technologies. The stochastic optimization tool, based on a genetic algorithm, was used to identify non-inferior solutions according to Pareto's dominance approach to optimization. The main tradeoff for fuel cycle optimization was found to be between economics and most of the other identified metrics. (Copies available exclusively from MIT Libraries, libraries.mit.edu/docs - docs mit.edu)

Recent trends in automobile recycling: An energy and economic assessment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Curlee, T.R.; Das, S.; Rizy, C.G.

1994-03-01

Recent and anticipated trends in the material composition of domestic and imported automobiles and the increasing cost of landfilling the non-recyclable portion of automobiles (automobile shredder residue or ASR) pose questions about the future of automobile recycling. This report documents the findings of a study sponsored by the US Department of Energy`s Office of Environmental Analysis to examine the impacts of these and other relevant trends on the life-cycle energy consumption of automobiles and on the economic viability of the domestic automobile recycling industry. More specifically, the study (1) reviewed the status of the automobile recycling industry in the Unitedmore » States, including the current technologies used to process scrapped automobiles and the challenges facing the automobile recycling industry; (2) examined the current status and future trends of automobile recycling in Europe and Japan, with the objectives of identifying ``lessons learned`` and pinpointing differences between those areas and the United States; (3) developed estimates of the energy system impacts of the recycling status quo and projections of the probable energy impacts of alternative technical and institutional approaches to recycling; and (4) identified the key policy questions that will determine the future economic viability of automobile shredder facilities in the United States.« less

Evolution of environmental responsibility in civil engineering

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lovell, C.W.

1995-12-31

Environmental responsibility has evolved slowly and only after abundant evidence of damage to the earth. The global issues constitute a formidable list, all of which require immediate attention and remediation. A basic principle which can unify and cause scientists and engineers to cooperate and synergize is that of Sustainable Development. In this strategy, development takes place with appropriate environmental sensitivity. Unless population growth rates are sharply decreased, man will undoubtedly exhaust food supplies, even given great technology developments. Sustainable technology will involve many ideas and approaches, but an important one is reuse/recycle of current wastes such as scrap rubber tires,more » coal combustion ash, and spent foundry sands. Paving should be recycled, as well, and products of building demolition should also be separated and reused. The author has significant personal interest in this topic, and has given some details in the paper.« less

Fed-batch hydrolysate addition and cell separation by settling in high cell density lignocellulosic ethanol fermentations on AFEX™ corn stover in the Rapid Bioconversion with Integrated recycling Technology process.

PubMed

Sarks, Cory; Jin, Mingjie; Balan, Venkatesh; Dale, Bruce E

2017-09-01

The Rapid Bioconversion with Integrated recycling Technology (RaBIT) process uses enzyme and yeast recycling to improve cellulosic ethanol production economics. The previous versions of the RaBIT process exhibited decreased xylose consumption using cell recycle for a variety of different micro-organisms. Process changes were tested in an attempt to eliminate the xylose consumption decrease. Three different RaBIT process changes were evaluated in this work including (1) shortening the fermentation time, (2) fed-batch hydrolysate addition, and (3) selective cell recycling using a settling method. Shorting the RaBIT fermentation process to 11 h and introducing fed-batch hydrolysate addition eliminated any xylose consumption decrease over ten fermentation cycles; otherwise, decreased xylose consumption was apparent by the third cell recycle event. However, partial removal of yeast cells during recycle was not economical when compared to recycling all yeast cells.

Addressing Criticality in Rare Earth Elements via Permanent Magnets Recycling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nlebedim, I. C.; King, A. H.

Rare earth elements (REEs) are critical for many advanced technologies and are faced with potential supply disruptions. Recycling of permanent magnets (PMs) can be good sources for REEs which can help minimize global dependence on freshly mined REEs, but PMs are rarely recycled. Recycling of PMs has been discussed with respect to improving REEs resource sustainability. Some challenges to be addressed in order to establish industrially deployable technologies for PMs recycling have also been discussed, including profitability, energy efficiency and environmental impacts. Key considerations for promoting circular economy via PMs recycling is proposed with the focus on deciding the targetmore » points in the supply chain at which the recycled products will be inserted. Important technical considerations for recycling different forms of waste PMs, including swarfs, slags, shredded and intact hard disk drives magnets, have been presented. Lastly, the aspects of circular economy considered include reusing magnets, remanufacturing magnets and recovering of REEs from waste PMs.« less

Addressing Criticality in Rare Earth Elements via Permanent Magnets Recycling

DOE PAGES

Nlebedim, I. C.; King, A. H.

2017-12-12

Rare earth elements (REEs) are critical for many advanced technologies and are faced with potential supply disruptions. Recycling of permanent magnets (PMs) can be good sources for REEs which can help minimize global dependence on freshly mined REEs, but PMs are rarely recycled. Recycling of PMs has been discussed with respect to improving REEs resource sustainability. Some challenges to be addressed in order to establish industrially deployable technologies for PMs recycling have also been discussed, including profitability, energy efficiency and environmental impacts. Key considerations for promoting circular economy via PMs recycling is proposed with the focus on deciding the targetmore » points in the supply chain at which the recycled products will be inserted. Important technical considerations for recycling different forms of waste PMs, including swarfs, slags, shredded and intact hard disk drives magnets, have been presented. Lastly, the aspects of circular economy considered include reusing magnets, remanufacturing magnets and recovering of REEs from waste PMs.« less

Present status of recycling waste mobile phones in China: a review.

PubMed

Li, Jingying; Ge, Zhongying; Liang, Changjin; An, Ni

2017-07-01

A large number of waste mobile phones have already been generated and are being generated. Various countries around the world have all been positively exploring the way of recycling and reuse when facing such a large amount of waste mobile phones. In some countries, processing waste mobile phones has been forming a complete industrial chain, which can not only recycle waste mobile phones to reduce their negative influence on the environment but also turn waste into treasure to acquire economic benefits dramatically. However, the situation of recycling waste mobile phones in China is not going well. Waste mobile phones are not formally covered by existing regulations and policies for the waste electric and electronic equipment in China. In order to explore an appropriate system to recover waste mobile phones, the mobile phone production and the amount of waste mobile phones are introduced in this paper, and status of waste mobile phones recycling is described; then, the disposal technology of electronic waste that would be most likely to be used for processing of electronic waste in industrial applications in the near future is reviewed. Finally, rationalization proposals are put forward based on the current recovery status of waste mobile phones for the purpose of promoting the development of recycling waste mobile phones in developing countries with a special emphasis on China.

Efficient dehydration and recovery of ionic liquid after lignocellulosic processing using pervaporation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sun, Jian; Shi, Jian; Murthy Konda, N. V. S. N.

Background Biomass pretreatment using certain ionic liquids (ILs) is very efficient, generally producing a substrate that is amenable to saccharification with fermentable sugar yields approaching theoretical limits. Although promising, several challenges must be addressed before an IL pretreatment technology can become commercially viable. One of the most significant challenges is the affordable and scalable recovery and recycle of the IL itself. Pervaporation (PV) is a highly selective and scalable membrane separation process for quantitatively recovering volatile solutes or solvents directly from non-volatile solvents that could prove more versatile for IL dehydration. Results We evaluated a commercially available PV system formore » IL dehydration and recycling as part of an integrated IL pretreatment process using 1-ethyl-3-methylimidazolium acetate ([C 2 C 1 Im][OAc] ) that has been proven to be very effective as a biomass pretreatment solvent. Separation factors as high as 1500 were observed. We demonstrate that > 99.9 wt% [C 2 C 1 Im][OAc] can be recovered from aqueous solution (≤20 wt% IL) and recycled five times. A preliminary technoeconomic analysis validated the promising role of PV in improving overall biorefinery process economics, especially in the case where other IL recovery technologies might lead to significant losses. Conclusions These findings establish the foundation for further development of PV as an effective method of recovering and recycling ILs using a commercially viable process technology.« less

Efficient dehydration and recovery of ionic liquid after lignocellulosic processing using pervaporation

DOE PAGES

Sun, Jian; Shi, Jian; Murthy Konda, N. V. S. N.; ...

2017-06-15

Background Biomass pretreatment using certain ionic liquids (ILs) is very efficient, generally producing a substrate that is amenable to saccharification with fermentable sugar yields approaching theoretical limits. Although promising, several challenges must be addressed before an IL pretreatment technology can become commercially viable. One of the most significant challenges is the affordable and scalable recovery and recycle of the IL itself. Pervaporation (PV) is a highly selective and scalable membrane separation process for quantitatively recovering volatile solutes or solvents directly from non-volatile solvents that could prove more versatile for IL dehydration. Results We evaluated a commercially available PV system formore » IL dehydration and recycling as part of an integrated IL pretreatment process using 1-ethyl-3-methylimidazolium acetate ([C 2 C 1 Im][OAc] ) that has been proven to be very effective as a biomass pretreatment solvent. Separation factors as high as 1500 were observed. We demonstrate that > 99.9 wt% [C 2 C 1 Im][OAc] can be recovered from aqueous solution (≤20 wt% IL) and recycled five times. A preliminary technoeconomic analysis validated the promising role of PV in improving overall biorefinery process economics, especially in the case where other IL recovery technologies might lead to significant losses. Conclusions These findings establish the foundation for further development of PV as an effective method of recovering and recycling ILs using a commercially viable process technology.« less

Enhanced Mixed Feedstock Processing Using Ionic Liquids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Simmons, Blake A

2016-10-22

Biomass pretreatment using certain ionic liquids (ILs) is very efficient, generally producing a substrate that is amenable to saccharification with fermentable sugar yields approaching theoretical limits. Although promising, several challenges must be addressed before IL pretreatment technology becomes commercially viable. Once of the most significant challenges is the affordable and scalable recovery and recycle or the IL itself. Pervaporation is a highly selective and scalable membrane separation process for quantitatively recovering volatile solutes or solvents directly from non-volatile solvents that could prove more versatile for IL dehydration than traditional solvent extraction processes, as well as efficient and energetically more advantageousmore » than standard evaporative techniques. In this study we evaluated a commercially available pervaporation system for IL dehydration and recycling as part of an integrated IL pretreatment process using 1-ethyl-3-methylimidazolium acetate ([C2C1Im][OAc]) that has been proven to be very effective as a biomass pretreatment solvent. We demonstrate that >99.9 wt% [C2C1Im][OAc] can be recovered from aqueous solution and recycled at least five times. A preliminary techno-economic analysis validated the promising role of pervaporation in improving overall biorefinery process economics, especially in the case where other IL recovery technologies might lead to significant losses. These findings establish the foundation for further development of pervaporation as an effective method of recovering and recycling ILs using a commercially viable process technology.« less

Spent lead-acid battery recycling in China - A review and sustainable analyses on mass flow of lead.

PubMed

Sun, Zhi; Cao, Hongbin; Zhang, Xihua; Lin, Xiao; Zheng, Wenwen; Cao, Guoqing; Sun, Yong; Zhang, Yi

2017-06-01

Lead is classified to be one of the top heavy metal pollutants in China. The corresponding environmental issues especially during the management of spent lead-acid battery have already caused significant public awareness and concern. This research gives a brief overview on the recycling situation based on an investigation of the lead industry in China and also the development of technologies for spent lead-acid batteries. The main principles and research focuses of different technologies including pyrometallurgy, hydrometallurgy and greener technologies are summarized and compared. Subsequently, the circulability of lead based on the entire life cycle analyses of lead-acid battery is calculated. By considering different recycling schemes, the recycling situation of spent lead-acid battery in China can be understood semi-quantitatively. According to this research, 30% of the primary lead production can be shut down that the lead production can still ensure consecutive life cycle operation of lead-acid battery, if proper management of the spent lead-acid battery is implemented according to current lead industry situation in China. This research provides a methodology on the view of lead circulability in the whole life cycle of a specific product and is aiming to contribute more quantitative guidelines for efficient organization of lead industry in China. Copyright © 2017 Elsevier Ltd. All rights reserved.

Mechanical and chemical recycling of solid plastic waste.

PubMed

Ragaert, Kim; Delva, Laurens; Van Geem, Kevin

2017-11-01

This review presents a comprehensive description of the current pathways for recycling of polymers, via both mechanical and chemical recycling. The principles of these recycling pathways are framed against current-day industrial reality, by discussing predominant industrial technologies, design strategies and recycling examples of specific waste streams. Starting with an overview on types of solid plastic waste (SPW) and their origins, the manuscript continues with a discussion on the different valorisation options for SPW. The section on mechanical recycling contains an overview of current sorting technologies, specific challenges for mechanical recycling such as thermo-mechanical or lifetime degradation and the immiscibility of polymer blends. It also includes some industrial examples such as polyethylene terephthalate (PET) recycling, and SPW from post-consumer packaging, end-of-life vehicles or electr(on)ic devices. A separate section is dedicated to the relationship between design and recycling, emphasizing the role of concepts such as Design from Recycling. The section on chemical recycling collects a state-of-the-art on techniques such as chemolysis, pyrolysis, fluid catalytic cracking, hydrogen techniques and gasification. Additionally, this review discusses the main challenges (and some potential remedies) to these recycling strategies and ground them in the relevant polymer science, thus providing an academic angle as well as an applied one. Copyright © 2017 Elsevier Ltd. All rights reserved.

Survey of metallurgical recycling processes. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pemsler, J.P.

1979-03-01

In the year 2000, the US will consume about 3.2 x 10/sup 15/ Btu to produce the seven major nonferrous metals Al, Cu, Zn, Pb, Ni, Mg, and Ti. Of this amount, 82% will be used in the production of Al. It is projected that 0.6 x 10/sup 15/ Btu will be saved by the recycle of secondary metals. Major opportunities for increasing the extent of recycle and thereby increasing the energy savings are discussed. An inherent feature in the energistics of recycle is that physical processes such as magnetic separation, density separations, melting, and in some instances vaporization aremore » far less energy intensive than are chemical processes associated with dissolution and electrowinning. It is in the domain of scrap of complex composition and physical form, difficult to handle by existing technology, that opportunities exist for new chemical recycle technology. Recycle of scrap metal of adequate grade is currently achieved through pyrometallurgical processes which, in many cases, are not very energy intensive as compared with hydrometallurgical processes. Preliminary flowsheets are presented for the recovery of value metals from batteries considered for use in vehicular propulsion and load leveling applications. The battery types examined are lead/acid, nickel/zinc, nickel/iron, zinc/chlorine, lithium-aluminum/iron sulfide, and sodium/sulfur. A flow sheet has been outlined for an integrated hydrometallurgical process to treat low-grade copper scrap. A fully integrated hydrometallurgical process is outlined, and costs and energy consumption are derived, for recovering zinc metal from electric furnace flue dusts. Costs and energy are high and the process does not appear to warrant development at this time. Improvement in the recycle of magnesium is associated primarily with improved recycle in the Al industry where Mg is an important alloy additive. Ni and Ti recycle are associated with improved collection and sorting of stainless steel and specialty alloys.« less

FY2013 Lightweight Materials R&D Annual Progress Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

2014-02-01

As part of the U.S. Department of Energy’s (DOE’s) Vehicle Technologies Program (VTO), the Lightweight Materials (LM) activity focuses on the development and validation of advanced materials and manufacturing technologies to significantly reduce light and heavy duty vehicle weight without compromising other attributes such as safety, performance, recyclability, and cost.

Sustainable recycling of automotive products in China: Technology and regulation

NASA Astrophysics Data System (ADS)

Chen, Ming

2006-08-01

The Chinese economy is growing rapidly, but accompanyingsuch growth are issues of environmental protection and social inequity which must be addressed. With the Automobile Industry Development Policy and the Motor Vehicle Product Recovery Technology Policy, an automobile products recoverability target has been established and will be incorporated into an automobile products authentication management system in China. By 2010, for all end-of-life automobile products, reuse and recovery shall be increased to a minimum of 85% by average weight per vehicle, and the use of lead, mercury, cadmium, and hexavalent chromium is prohibited. This paper will address the sustainable recycling of Chinese automobile products within the period of 2006 2010.

New technology for separating resin powder and fiberglass powder from fiberglass-resin powder of waste printed circuit boards.

PubMed

Li, Jia; Gao, Bei; Xu, Zhenming

2014-05-06

New recycling technologies have been developed lately to enhance the value of the fiberglass powder-resin powder fraction (FRP) from waste printed circuit boards. The definite aim of the present paper is to present some novel methods that use the image forces for the separation of the resin powder and fiberglass powder generated from FRP during the corona electrostatic separating process. The particle shape charactization and particle trajectory simulation were performed on samples of mixed non-metallic particles. The simulation results pointed out that particles of resin powder and particles of fiberglass powder had different detach trajectories at the conditions of the same size and certain device parameters. An experiment carried out using a corona electrostatic separator validated the possibility of sorting these particles based on the differences in their shape characteristics. The differences in the physical properties of the different types of particles provided the technical basis for the development of electrostatic separation technologies for the recycling industry.

U.S. Army Technology Collaboration Briefing

DTIC Science & Technology

2012-09-11

engine boosting ( turbo chargers and super chargers), homogeneous charged compression, direct injection, etc. • Advanced light-weight materials...mitigation, recycling, and supply chain development. • Alternative fuels including biofuels, hydrogen, electricity, diesel , etc. • Vehicle

Study on Insulating Material by Renewable Resources

NASA Astrophysics Data System (ADS)

Kurata, Yasuyuki; Kurosumi, Akihiro; Ishikawa, Keita

Under circumstances such as global warming caused by carbon dioxide and other green house gas and crisis of depletion of fossil resources, recyclable resources such as biomass have captured the world's attention as reproducible resources alternative to petroleum. Therefore the technologies such to manufacture chemicals from recyclable resources have been developed for the achievement of measures for controlling global warming and the low carbon society. Recently, the bioplastic such as polylactic resin is applied to the home appliances and the automobile interior part as substitution of general-purpose plastic Moreover, the insulation oil from the vegetable oil has been put to practical use. The application of recyclable resources is extending in an electric field. In this paper, we introduce the characteristic and the problem of the insulating material made from recyclable resources in the field of the solid insulation.

Recycling Technology: Can It Be Taught?

ERIC Educational Resources Information Center

Clum, James A.; Loper, Carl R., Jr.

This paper describes the content of a seminar-type engineering course dealing with materials reutilization (recycling). The course, consisting of lecture and discussion by various faculty and outside experts as well as student presentations of research papers on recycling topics, is intended to investigate current areas in which recycling of…

Anaerobes, aerobes and phototrophs. A winning team for wastewater management.

PubMed

Gijzen, H J

2001-01-01

Current mainstream technologies for wastewater treatment, such as activated sludge and tertiary nutrient removal, are too costly to provide a satisfactory solution for the increasing wastewater problems in developing regions. Besides, these technologies do not allow for re-use of valuable energy and nutrients contained in the wastewater. In light of these limitations, it is important to reconsider the technology and strategic approaches in wastewater management. This paper introduces the "Cleaner Production" concept to sewage management, which combines two approaches: pollution prevention and re-use. Pollution prevention includes a shift towards low water use sanitation technology. The more concentrated wastewater, becomes more attractive for re-use oriented treatment schemes. A combination of anaerobic pre-treatment followed by macrophyte-covered stabilisation ponds is proposed for the effective recovery of energy and nutrients from sewage. By selecting optimal applications of the plant biomass and pond effluent, nutrients will end up as fish and crop protein. This contrasts favourably to tertiary nitrogen removal in activated sludge systems, which recycles ammonia through molecular nitrogen at the expense of energy and high costs. Macrophyte ponds are proposed as a key step in waste recycling, because these form the central unit of a recycling engine, driven by photosynthesis. The process is energy efficient, cost effective and applicable under a wide variety of rural and urban conditions.

Argonne explains nuclear recycling in 4 minutes

ScienceCinema

Willit, Jim; Williamson, Mark; Haynes, Amber

2018-05-30

Currently, when using nuclear energy only about five percent of the uranium used in a fuel rod gets fissioned for energy; after that, the rods are taken out of the reactor and put into permanent storage. There is a way, however, to use almost all of the uranium in a fuel rod. Recycling used nuclear fuel could produce hundreds of years of energy from just the uranium we've already mined, all of it carbon-free. Problems with older technology put a halt to recycling used nuclear fuel in the United States, but new techniques developed by scientists at Argonne National Laboratory address many of those issues. For more information, visit http://www.anl.gov/energy/nuclear-energy.

Human life support for advanced space exploration

NASA Technical Reports Server (NTRS)

Schwartzkopf, S. H.

1997-01-01

The requirements for a human life support system for long-duration space missions are reviewed. The system design of a controlled ecological life support system is briefly described, followed by a more detailed account of the study of the conceptual design of a Lunar Based CELSS. The latter is to provide a safe, reliable, recycling lunar base life support system based on a hybrid physicochemical/biological representative technology. The most important conclusion reached by this study is that implementation of a completely recycling CELSS approach for a lunar base is not only feasible, but eminently practical. On a cumulative launch mass basis, a 4-person Lunar Base CELSS would pay for itself in approximately 2.6 years relative to a physicochemical air/water recycling system with resupply of food from the Earth. For crew sizes of 30 and 100, the breakeven point would come even sooner, after 2.1 and 1.7 years, respectively, due to the increased mass savings that can be realized with the larger plant growth units. Two other conclusions are particularly important with regard to the orientation of future research and technology development. First, the mass estimates of the Lunar Base CELSS indicate that a primary design objective in implementing this kind of system must be to minimized the mass and power requirement of the food production plant growth units, which greatly surpass those of the other air and water recycling systems. Consequently, substantial research must be directed at identifying ways to produce food more efficiently. On the other hand, detailed studies to identify the best technology options for the other subsystems should not be expected to produce dramatic reductions in either mass or power requirement of a Lunar Base CELSS. The most crucial evaluation criterion must, therefore, be the capability for functional integration of these technologies into the ultimate design of the system. Secondly, this study illustrates that existing or near-term technologies are adequate to implement a Lunar Base CELSS. There are no apparent "show-stoppers" which require the development of new technologies. However, there are several areas in which new materials and technologies could be used for a more efficient implementation of the system, e.g., by decreasing mass or power requirement and increasing recycling efficiency. These areas must be further addressed through research and development. Finally, although this study focused on the development of a Lunar Base CELSS, the same technologies and a nearly identical design would be appropriate for a Mars base. Actually, except for the distance of transportation, the implementation of a CELSS on Mars would even be easier than it would be on the Moon. The presence of atmospheric CO2 on Mars, although in low concentration, coupled with the fact that the day/night cycle on Mars is very similar to that on Earth, makes the use of light-weight, greenhouse-like structures for growing food plants even more feasible than on the Moon. There are some environmental problems, which would have to be dealt with, like dust storms and the large amount of the ultraviolet radiation incident on the planet's surface. However, the materials and methods are largely available today to develop such a life support system for a Mars base.

Human life support for advanced space exploration.

PubMed

Schwartzkopf, S H

1997-01-01

The requirements for a human life support system for long-duration space missions are reviewed. The system design of a controlled ecological life support system is briefly described, followed by a more detailed account of the study of the conceptual design of a Lunar Based CELSS. The latter is to provide a safe, reliable, recycling lunar base life support system based on a hybrid physicochemical/biological representative technology. The most important conclusion reached by this study is that implementation of a completely recycling CELSS approach for a lunar base is not only feasible, but eminently practical. On a cumulative launch mass basis, a 4-person Lunar Base CELSS would pay for itself in approximately 2.6 years relative to a physicochemical air/water recycling system with resupply of food from the Earth. For crew sizes of 30 and 100, the breakeven point would come even sooner, after 2.1 and 1.7 years, respectively, due to the increased mass savings that can be realized with the larger plant growth units. Two other conclusions are particularly important with regard to the orientation of future research and technology development. First, the mass estimates of the Lunar Base CELSS indicate that a primary design objective in implementing this kind of system must be to minimized the mass and power requirement of the food production plant growth units, which greatly surpass those of the other air and water recycling systems. Consequently, substantial research must be directed at identifying ways to produce food more efficiently. On the other hand, detailed studies to identify the best technology options for the other subsystems should not be expected to produce dramatic reductions in either mass or power requirement of a Lunar Base CELSS. The most crucial evaluation criterion must, therefore, be the capability for functional integration of these technologies into the ultimate design of the system. Secondly, this study illustrates that existing or near-term technologies are adequate to implement a Lunar Base CELSS. There are no apparent "show-stoppers" which require the development of new technologies. However, there are several areas in which new materials and technologies could be used for a more efficient implementation of the system, e.g., by decreasing mass or power requirement and increasing recycling efficiency. These areas must be further addressed through research and development. Finally, although this study focused on the development of a Lunar Base CELSS, the same technologies and a nearly identical design would be appropriate for a Mars base. Actually, except for the distance of transportation, the implementation of a CELSS on Mars would even be easier than it would be on the Moon. The presence of atmospheric CO2 on Mars, although in low concentration, coupled with the fact that the day/night cycle on Mars is very similar to that on Earth, makes the use of light-weight, greenhouse-like structures for growing food plants even more feasible than on the Moon. There are some environmental problems, which would have to be dealt with, like dust storms and the large amount of the ultraviolet radiation incident on the planet's surface. However, the materials and methods are largely available today to develop such a life support system for a Mars base.

Fatigue performance of asphalt pavements containing RAS and RAP.

DOT National Transportation Integrated Search

2015-01-01

Rising oil and gas prices spurs development of methods and technologies for reducing fuel consumption and increased use of : recycled materials. With increased environmental awareness, using reclaimed asphalt pavement (RAP) and reclaimed asphalt : sh...

Presidential Green Chemistry Challenge: 2008 Greener Synthetic Pathways Award

EPA Pesticide Factsheets

Presidential Green Chemistry Challenge 2008 award winner, Battelle, developed a biobased soy toner for laser printers and copiers. The technology saves energy and improves de-inking, allowing more paper fiber to be recycled.

SITE DEMONSTRATION OF THE TORONTO HARBOUR COMMISSIONERS SOIL RECYCLING PROJECT

EPA Science Inventory

The U.S. Environmental Protection Agency (EPA), in cooperation with the Toronto Harbour Commissioners (THC), conducted a Superfund InnovativeTechnology Evaluation (SITE) demonstration of the THC Soil Recycle Treatment Train. The treatment train consists of three technologies op...

Assessing the sustainability of lead utilization in China.

PubMed

Sun, Lingyu; Zhang, Chen; Li, Jinhui; Zeng, Xianlai

2016-12-01

Lead is not only one of heavy metals imposing environment and health risk, but also critical resource to maintain sustainable development of many industries. Recently, due to the shortage of fossil fuels, clean energy vehicles, including electric bicycle, have emerged and are widely adopted soon in the world. China became the world's largest producer of primary lead and a very significant consumer in the past decade, which has strained the supplies of China's lead deposits from lithosphere and boost the anthropogenic consumption of metallic lead and lead products. Here we summarize that China's lead demand will continually increase due to the rapid growth of electric vehicle, resulting in a short carrying duration of lead even with full lead recycling. With these applications increasing at an annual rate of 2%, the carrying duration of lead resource until 2030 will oblige that recycling rate should be not less than 90%. To sustain lead utilization in China, one approach would be to improve the utilization technology, collection system and recycling technology towards closed-loop supply chain. Other future endeavors should include optimizing lead industrial structure and development of new energy. Copyright © 2016 Elsevier Ltd. All rights reserved.

Resource Recovery. Redefining the 3 Rs. Reduce...Reuse...Recycle. Resources in Technology.

ERIC Educational Resources Information Center

Technology Teacher, 1991

1991-01-01

Discusses the problems of waste disposal, recycling, and resource recovery. Includes information on the social and cultural impact, the three classes of resource recovery (reuse, direct recycling, and indirect recycling), and specific products (paper, glass, plastics, metals, and so on). Includes a student quiz and possible outcomes. (JOW)

Ideas and Activities for Recycling Education for Grades K-12.

ERIC Educational Resources Information Center

Ayers, Jerry B., Ed.; Olberding, April H., Ed.

In June 1997, Tennessee Technological University's Center for Manufacturing Research conducted a one-week program on plastics recycling for science teachers. The purpose of the program was to increase the teachers' basic knowledge about the importance of recycling plastics and to better prepare the teachers for teaching recycling in the classroom.…

Life Support Goals Including High Closure and Low Mass Should Be Reconsidered Using Systems Analysis

NASA Technical Reports Server (NTRS)

Jones, Harry W.

2017-01-01

Recycling space life support systems have been built and tested since the 1960s and have operated on the International Space Station (ISS) since the mid 2000s. The development of space life support has been guided by a general consensus focused on two important related goals, increasing system closure and reducing launch mass. High closure is achieved by recycling crew waste products such as carbon dioxide and condensed humidity. Recycling directly reduces the mass of oxygen and water for the crew that must be launched from Earth. The launch mass of life support can be further reduced by developing recycling systems with lower hardware mass and reduced power. The life support consensus has also favored using biological systems. The goal of increasing closure using biological systems suggests that food should be grown in space and that biological processors be used for air, water, and waste recycling. The goal of reducing launch mass led to use of Equivalent System Mass (ESM) in life support advocacy and technology selection. The recent consensus assumes that the recycling systems architecture developed in the 1960s and implemented on ISS will be used on all future long missions. NASA and other project organizations use the standard systems engineering process to guide hardware development. The systems process was used to develop ISS life support, but it has been less emphasized in planning future systems for the moon and Mars. Since such missions are far in the future, there has been less immediate need for systems engineering analysis to consider trade-offs, reliability, and Life Cycle Cost (LCC). Preliminary systems analysis suggests that the life support consensus concepts should be revised to reflect systems engineering requirements.

Dust recycling technology in Kimitsu Works

NASA Astrophysics Data System (ADS)

Oda, Hiroshi; Ibaraki, Tetsuharu

Dust recycling technology by the rotary hearth furnace has been applied at Nippon Steel‧s Kimitsu Works since 2000. The dust and sludge with iron oxide and carbon are agglomerated into shaped articles and the iron oxide is reduced in a high temperature atmosphere. Zinc and other impurities in the dust and sludge are expelled and exhausted into off gas. The DRI pellets made from the dust and sludge have 70% metallization and are strong enough for being recycled to the blast furnaces. No.1 plant, which was constructed in May 2000 and has an agglomeration method of pelletizing, recycles mainly dry dusts. No.2 plant, which was constructed in December 2002 and has an agglomeration method of extrusion, recycles mainly sludge. The combination of the two plants is a solution for recycling various kinds of dusts and sludge emitted in a large scale steel works as Kimitsu Works

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, F. G.; Daniels, E. J.

This report summarizes an assessment conducted by Environmental Technologies Alternatives, Inc., under a subcontract to Argonne National Laboratory. The project was conducted in two phases. An assessment of alternative technologies for recycling of prompt non-tire rubber was conducted in the first phase, and an experimental program focusing on a new technology called the catalytic Regeneration Process offered the greatest opportunity for recovery of high-value recyclable rubber material. An experimental and large-scale test program was undertaken to further delineate the economic potential as an essential step leading to commercial deployment and to determine the course of continued development of the technologymore » by the private sector. The experimental program defined process-operating conditions for the technology and verified the degree of devulcanisation achievable for two rubber compounds: ethylene-propylene-nonconjugated-diene monomer (EPDM) and neoprene. To determine product acceptance, samples of devulcanized EPDM and neoprene were prepared and used in factory trials for the production of automotive moldings (EPDM) and fiber-filled belting (neoprene). The factory trials indicated that the physical properties of the products were acceptable in both cases. The appearance of molded and calendared surface finishes was acceptable, while that of extruded finishes was unsatisfactory. The fiber-filled neoprene belting application offers the greatest economic potential. Process costs were estimated at $0.34/lb for neoprene waste rubber relative to a value of $0.57/lb. The results of the experimental program led to the decision to continue development of this technology is being planned, subject to the availability of about $3 million in financing from private-sector investors. The ability to recycle non-tire rubber scrap could conserve as much as 90,000 Btu/lb, thus yielding an estimated energy savings potential of about 0.25 quad/yr.« less

EVALUATION OF RECYCLED PLASTIC LUMBER FOR MARINE APPLICATIONS

EPA Science Inventory

This report presents an evaluation of the recycled plastic materials (RPM) produced by California Recycling Company (CRC). his evaluation is performed under the Municipal Waste Innovative Technology Evaluation (MITE) Program of the U.S. EPA, Risk Reduction Engineering Laboratory....

EVALUATION OF RECYCLED PLASTIC LUMBER FOR MARINE APPLICATIONS

EPA Science Inventory

This report presents an evaluation of the recycled plastic materials (RPM) produced by California Recycling Company (CRC). This evaluation is performed under the Municipal Waste Innovative Technology Evaluation (MITE) Program of the U.S. EPA, Risk Reduction Engineering Laboratory...

Evaluation of recycled projects for performance : final report.

DOT National Transportation Integrated Search

1995-04-01

Louisiana constructed two hot mix recycling projects in 1978 in order to determine the feasibility of this technology with respect to design and construction. In 1980-81 four recycled projects were constructed to examine the variations found in recyc...

Recycling of nickel-metal hydride battery scrap

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lyman, J.W.; Palmer, G.R.

1994-12-31

Nickel-metal hydride (Ni-MH) battery technology is being developed as a NiCd replacement for applications in consumer cells and electric vehicle batteries. The U.S. Bureau of Mines is investigating hydrometallurgical recycling technology that separates and recovers individual components from Ni-MH battery scrap. Acid dissolution and metal recovery techniques such as precipitation and solvent extraction produced purified products of rare-earths, nickel, and other metals associated with AB{sub 2} and AB{sub 5} Ni-MH scrap. Tests were conducted on scrap cells of a single chemistry that had been de-canned to reduce iron content. Although recovery techniques have been identified in principal, their applicability tomore » mixed battery waste stream and economic attractiveness remain to be demonstrated. 14 refs.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hadi, Pejman; Ning, Chao; Ouyang, Weiyi

Highlights: • Environmental impacts of electronic waste and specifically waste printed circuit boards. • Review of the recycling techniques of waste printed circuit boards. • Advantages of physico-mechanical recycling techniques over chemical methods. • Utilization of nonmetallic fraction of waste printed circuit boards as modifier/filler. • Recent advances in the use of nonmetallic fraction of waste printed circuit boards as precursor. - Abstract: Electronic waste, including printed circuit boards, is growing at an alarming rate due to the accelerated technological progress and the shorter lifespan of the electronic equipment. In the past decades, due to the lack of proper economicmore » and environmentally-benign recycling technologies, a major fraction of e-waste generated was either destined to landfills or incinerated with the sole intention of its disposal disregarding the toxic nature of this waste. Recently, with the increasing public awareness over their environment and health issues and with the enaction of more stringent regulations, environmentally-benign recycling has been driven to be an alternative option partially replacing the traditional eco-unfriendly disposal methods. One of the most favorable green technologies has been the mechanical separation of the metallic and nonmetallic fraction of the waste printed circuit boards. Although metallic fraction, as the most profitable component, is used to generate the revenue of the separation process, the nonmetallic fraction (NMF) has been left isolated. Herein, the recent developments in the application of NMF have been comprehensively reviewed and an eco-friendly emerging usage of NMF as a value-added material for sustainable remediation has been introduced.« less

Methane Post-Processor Development to Increase Oxygen Recovery beyond State-of-the-Art Carbon Dioxide Reduction Technology

NASA Technical Reports Server (NTRS)

Abney, Morgan; Miller, Lee; Greenwood, Zach; Iannantuono, Michelle; Jones, Kenny

2013-01-01

State-of-the-art life support carbon dioxide (CO2) reduction technology, based on the Sabatier reaction, is theoretically capable of 50% recovery of oxygen from metabolic CO2. This recovery is constrained by the limited availability of reactant hydrogen. Post-processing of the methane byproduct from the Sabatier reactor results in hydrogen recycle and a subsequent increase in oxygen recovery. For this purpose, a Methane Post-Processor Assembly containing three sub-systems has been developed and tested. The assembly includes a Methane Purification Assembly (MePA) to remove residual CO2 and water vapor from the Sabatier product stream, a Plasma Pyrolysis Assembly (PPA) to partially pyrolyze methane into hydrogen and acetylene, and an Acetylene Separation Assembly (ASepA) to purify the hydrogen product for recycle. The results of partially integrated testing of the sub-systems are reported.

Methane Post-Processor Development to Increase Oxygen Recovery beyond State-of-the-Art Carbon Dioxide Reduction Technology

NASA Technical Reports Server (NTRS)

Abney, Morgan B.; Greenwood, Zachary; Miller, Lee A.; Alvarez, Giraldo; Iannantuono, Michelle; Jones, Kenny

2013-01-01

State-of-the-art life support carbon dioxide (CO2) reduction technology, based on the Sabatier reaction, is theoretically capable of 50% recovery of oxygen from metabolic CO2. This recovery is constrained by the limited availability of reactant hydrogen. Post-processing of the methane byproduct from the Sabatier reactor results in hydrogen recycle and a subsequent increase in oxygen recovery. For this purpose, a Methane Post-Processor Assembly containing three sub-systems has been developed and tested. The assembly includes a Methane Purification Assembly (MePA) to remove residual CO2 and water vapor from the Sabatier product stream, a Plasma Pyrolysis Assembly (PPA) to partially pyrolyze methane into hydrogen and acetylene, and an Acetylene Separation Assembly (ASepA) to purify the hydrogen product for recycle. The results of partially integrated testing of the sub-systems are reported

Electrical and electronic waste: a global environmental problem.

PubMed

Ramesh Babu, Balakrishnan; Parande, Anand Kuber; Ahmed Basha, Chiya

2007-08-01

The production of electrical and electronic equipment (EEE) is one of the fastest growing global manufacturing activities. This development has resulted in an increase of waste electric and electronic equipment (WEEE). Rapid economic growth, coupled with urbanization and growing demand for consumer goods, has increased both the consumption of EEE and the production of WEEE, which can be a source of hazardous wastes that pose a risk to the environment and to sustainable economic growth. To address potential environmental problems that could stem from improper management of WEEE, many countries and organizations have drafted national legislation to improve the reuse, recycling and other forms of material recovery from WEEE to reduce the amount and types of materials disposed in landfills. Recycling of waste electric and electronic equipment is important not only to reduce the amount of waste requiring treatment, but also to promote the recovery of valuable materials. EEE is diverse and complex with respect to the materials and components used and waste streams from the manufacturing processes. Characterization of these wastes is of paramount importance for developing a cost-effective and environmentally sound recycling system. This paper offers an overview of electrical and e-waste recycling, including a description of how it is generated and classified, strategies and technologies for recovering materials, and new scientific developments related to these activities. Finally, the e-waste recycling industry in India is also discussed.

The status and development of treatment techniques of typical waste electrical and electronic equipment in China: a review.

PubMed

He, Yunxia; Xu, Zhenming

2014-04-01

A large quantity of waste electrical and electronic equipment (WEEE) is being generated because technical innovation promotes the unceasing renewal of products. China's household appliances and electronic products have entered the peak of obsolescence. Due to lack of technology and equipment, recycling of WEEE is causing serious environment pollution. In order to achieve the harmless disposal and resource utilization of WEEE, researchers have performed large quantities of work, and some demonstration projects have been built recently. In this paper, the treatment techniques of typical WEEE components, including printed circuit boards, refrigerator cabinets, toner cartridges, cathode ray tubes, liquid crystal display panels, batteries (Ni-Cd and Li-ion), hard disk drives, and wires are reviewed. An integrated recycling system with environmentally friendly and highly efficient techniques for processing WEEE is proposed. The orientation of further development for WEEE recycling is also proposed.

Evaluation of the Benefits Attributable to Automotive Lighweight Materials Program Research and Development Projects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Das, S.

The purpose of this project is to identify and test methods appropriate for estimating the benefits attributable to research and development (R and D) projects funded by the Automotive Lightweight Materials (ALM) Program of the Office of Advanced Automotive Technologies (OAAT) of the U.S. Department of Energy (DOE). The program focuses on the development and validation of advanced lightweight materials technologies to significantly reduce automotive vehicle body and chassis weight without compromising other attributes such as safety, performance, recyclability, and cost. The work supports the goals of the Partnership for a New Generation of Vehicles (PNGV). Up to thirty percentmore » of the improvement required to meet the PNGV goal of tripling vehicle fuel economy and much of its cost, safety, and recyclability goal depend on the lightweight materials. Funded projects range from basic materials science research to applied research in production environments. Collaborators on these projects include national laboratories, universities, and private sector firms, such as leading automobile manufacturers and their suppliers.« less

Waste processing: new near infrared technologies for material identification and selection

NASA Astrophysics Data System (ADS)

Cesetti, M.; Nicolosi, P.

2016-09-01

The awareness of environmental issues on a global scale increases the opportunities for waste handling companies. Recovery is set to become all the more important in areas such as waste selection, minerals processing, electronic scrap, metal and plastic recycling, refuse and the food industry. Effective recycling relies on effective sorting. Sorting is a fundamental step of the waste disposal/recovery process. The big players in the sorting market are pushing for the development of new technologies to cope with literally any type of waste. The purpose of this tutorial is to gain an understanding of waste management, frameworks, strategies, and components that are current and emerging in the field. A particular focus is given to spectroscopic techniques that pertains the material selection process with a greater emphasis placed on the NIR technology for material identification. Three different studies that make use of NIR technology are shown, they are an example of some of the possible applications and the excellent results that can be achieved with this technique.

Plastic recycling in the Nordics: A value chain market analysis.

PubMed

Milios, Leonidas; Holm Christensen, Lena; McKinnon, David; Christensen, Camilla; Rasch, Marie Katrine; Hallstrøm Eriksen, Mikael

2018-06-01

There is low utilisation of plastic waste in the Nordic region and only a fraction of plastic materials go back into production processes through reuse and recycling practices. This paper aims to increase knowledge concerning factors that inhibit demand for recycled plastics, and to identify critical barriers for plastic recycling across the regional plastics value chain. A literature review and targeted interviews with key actors across the plastics value chain enabled the mapping of interactions between the major actors and identified hotspots that act as barriers to the flow of plastic materials. Barriers identified include the lack of both supply and demand of recycled plastic and are mainly attributed to the fragmented market of secondary materials. The main hotspots identified are the low demand due to price considerations, insufficient traceability and transparency in value chain transactions, and general design deficiencies in the recyclability of products. Value chain coordination is considered as the most important intervention by the interviewees, followed by the need for increased investment in innovation and technology development. Complementary measures that could counteract the identified barriers include public procurement for resource efficiency, ban on the incineration of recyclable materials, and specifications on the design of plastic products for reducing the number of different polymers, and the number and usage of additives. Copyright © 2018 Elsevier Ltd. All rights reserved.

77 FR 24701 - Agency Information Collection Activities; Submission to OMB for Review and Approval; Comment...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-25

... Backwash Recycling Rule (FBRR), Long Term 1 Enhanced Surface Water Treatment Rule (LT1ESWTR), Long Term 2... review instructions; develop, acquire, install, and utilize technology and systems for the purposes of...

Stock dynamics and emission pathways of the global aluminum cycle

NASA Astrophysics Data System (ADS)

Müller, Daniel B.; Liu, Gang; Bangs, Colton

Climate change mitigation in the materials sector faces a twin challenge: satisfying rapidly rising global demand for materials while significantly curbing greenhouse-gas emissions. Process efficiency improvement and recycling can contribute to reducing emissions per material output; however, long-term material demand and scrap availability for recycling depend fundamentally on the dynamics of societies' stocks of products in use, an issue that has been largely neglected in climate science. Here, we show that aluminium in-use stock patterns set essential boundary conditions for future emission pathways, which has significant implications for mitigation priority setting. If developing countries follow industrialized countries in their aluminium stock patterns, a 50% emission reduction by 2050 below 2000 levels cannot be reached even under very optimistic recycling and technology assumptions. The target can be reached only if future global per-capita aluminium stocks saturate at a level much lower than that in present major industrialized countries. As long as global in-use stocks are growing rapidly, radical new technologies in primary production (for example, inert anode and carbon capture and storage) have the greatest impact in emission reduction; however, their window of opportunity is closing once the stocks begin to saturate and the largest reduction potential shifts to post-consumer scrap recycling.

Radioactivity and radiological risk associated with effluent sediment containing technologically enhanced naturally occurring radioactive materials in amang (tin tailings) processing industry.

PubMed

Bahari, Ismail; Mohsen, Nasirian; Abdullah, Pauzi

2007-01-01

The processing of amang, or tin tailings, for valuable minerals has been shown to technologically enhance NORM and this has stirred significant radiological safety and health concerns among Malaysia's regulatory authority. A growing radiological concern is now focused on the amang effluent containing NORM in recycling ponds, since these ponds may be reclaimed for future residential developments. A study was carried out to assess the radiological risk associated with amang processing and the accumulated effluent in the recycling ponds. Twenty-six sediment samples from the recycling ponds of two amang plants in the states of Selangor and Perak, Malaysia, were collected and analyzed. The maximum activity concentrations of (238)U, (226)Ra, (232)Th and (40)K recorded in sediments from these ponds were higher than Malaysia's and the world's natural highest. Correspondingly, the mean radium equivalent activity concentration indices, Ra(eq), and gamma radiation representative level index, I(gammar), were higher than the world's average. The enhancement of NORM in effluent sediments as a consequence of amang processing, and the use of a closed water management recycling system created Effective Dose Rates, E (nSv h(-1)), that signal potential environmental radiological risks in these ponds, should they be reclaimed for future land use.

Supply and demand of some critical metals and present status of their recycling in WEEE.

PubMed

Zhang, Shengen; Ding, Yunji; Liu, Bo; Chang, Chein-Chi

2017-07-01

New development and technological innovations make electrical and electronic equipment (EEE) more functional by using an increasing number of metals, particularly the critical metals (e.g. rare and precious metals) with specialized properties. As millions of people in emerging economies adopt a modern lifestyle, the demand for critical metals is soaring. However, the increasing demand causes the crisis of their supply because of their simple deficiency in the Earth's crust or geopolitical constraints which might create political issues for their supply. This paper focuses on the sustainable supply of typical critical metals (indium, rare earth elements (REEs), lithium, cobalt and precious metals) through recycling waste electrical and electronic equipment (WEEE). To illuminate this issue, the production, consumption, expected future demand, current recycling situation of critical metals, WEEE management and their recycling have been reviewed. We find that the demand of indium, REEs, lithium and cobalt in EEE will continuously increasing, while precious metals are decreasing because of new substitutions with less or even without precious metals. Although the generation of WEEE in 2014 was about 41.9 million tons (Mt), just about 15% (6.5 Mt) was treated environmentally. The inefficient collection of WEEE is the main obstacle to relieving the supply risk of critical metals. Furthermore, due to the widespread use in low concentrations, such as indium, their recycling is not just technological problem, but economic feasibility is. Finally, relevant recommendations are point out to address these issues. Copyright © 2017 Elsevier Ltd. All rights reserved.

EVALUATION OF FILTRATION AND DISTILLATION METHODS FOR RECYCLING AUTOMOTIVE COOLANT.

EPA Science Inventory

This evaluation addresses the product quality, waste reduction, and economic issues involved in recycling automotive and heavy-duty engine coolants at a New Jersey Department of Transportation garage. The specific recycling units evaluated are based on the technologies of filtrat...

Recycling of wood and paper products in the United States

Treesearch

Peter J. Ince

1996-01-01

This report describes the current status of wood and paper recycling in the United States and predicts the production and market consequences of increased recycling. The results suggest that the rate of paper recycling will rapidly rise in the 1990s, mainly as a result of the competitive evolution of fiber markets and papermaking technologies. The consumption and...

Nitrogen removal by recycle water nitritation as an attractive alternative for retrofit technologies in municipal wastewater treatment plants.

PubMed

Gil, K I; Choi, E

2004-01-01

The recycle water from sludge processing in municipal wastewater treatment plants causes many serious problems in the efficiency and stability of the mainstream process. Thus, the design approach for recycle water is an important part of any biological nutrient removal system design when a retrofit technology is required for upgrading an existing plant. Moreover, the application of nitrogen removal from recycle water using the nitritation process has recently increased due to economic reasons associated with an effective carbon allocation as well as the minimization of aeration costs. However, for the actual application of recycle water nitritation, it has not been fully examined whether or not additional volume would be required in an existing plant. In this paper, the addition of recycle water nitritation to an existing plant was evaluated based on a volume analysis and estimation of final effluent quality. It was expected that using the reserve volume of the aeration tank in existing plants, recycle water nitritation could be applied to a plant without any enlargement. With the addition of recycle water nitritation, it was estimated that the final effluent quality would be improved and stabilized, especially in the winter season.

Recyclable organic solar cells on cellulose nanocrystal substrates

PubMed Central

Zhou, Yinhua; Fuentes-Hernandez, Canek; Khan, Talha M.; Liu, Jen-Chieh; Hsu, James; Shim, Jae Won; Dindar, Amir; Youngblood, Jeffrey P.; Moon, Robert J.; Kippelen, Bernard

2013-01-01

Solar energy is potentially the largest source of renewable energy at our disposal, but significant advances are required to make photovoltaic technologies economically viable and, from a life-cycle perspective, environmentally friendly, and consequently scalable. Cellulose nanomaterials are emerging high-value nanoparticles extracted from plants that are abundant, renewable, and sustainable. Here, we report on the first demonstration of efficient polymer solar cells fabricated on optically transparent cellulose nanocrystal (CNC) substrates. The solar cells fabricated on the CNC substrates display good rectification in the dark and reach a power conversion efficiency of 2.7%. In addition, we demonstrate that these solar cells can be easily separated and recycled into their major components using low-energy processes at room temperature, opening the door for a truly recyclable solar cell technology. Efficient and easily recyclable organic solar cells on CNC substrates are expected to be an attractive technology for sustainable, scalable, and environmentally-friendly energy production. PMID:23524333

Recyclable organic solar cells on cellulose nanocrystal substrates.

PubMed

Zhou, Yinhua; Fuentes-Hernandez, Canek; Khan, Talha M; Liu, Jen-Chieh; Hsu, James; Shim, Jae Won; Dindar, Amir; Youngblood, Jeffrey P; Moon, Robert J; Kippelen, Bernard

2013-01-01

Solar energy is potentially the largest source of renewable energy at our disposal, but significant advances are required to make photovoltaic technologies economically viable and, from a life-cycle perspective, environmentally friendly, and consequently scalable. Cellulose nanomaterials are emerging high-value nanoparticles extracted from plants that are abundant, renewable, and sustainable. Here, we report on the first demonstration of efficient polymer solar cells fabricated on optically transparent cellulose nanocrystal (CNC) substrates. The solar cells fabricated on the CNC substrates display good rectification in the dark and reach a power conversion efficiency of 2.7%. In addition, we demonstrate that these solar cells can be easily separated and recycled into their major components using low-energy processes at room temperature, opening the door for a truly recyclable solar cell technology. Efficient and easily recyclable organic solar cells on CNC substrates are expected to be an attractive technology for sustainable, scalable, and environmentally-friendly energy production.

Recycle/Reuse: Utilizing New Technology.

ERIC Educational Resources Information Center

Vaglia, John S.

In the early 1990s, efforts were initiated to help countries move toward a solution of the global pollution problem. Technology education classrooms and laboratories are among the best places for bring the concepts of recycling/reuse and waste management to students' attention. Important concepts about pollution, waste prevention, and recycling…

Recycling of car tires by means of Waterjet technologies

NASA Astrophysics Data System (ADS)

Holka, Henryk; Jarzyna, Tomasz

2017-03-01

An increasing number of used car tires poses a threat to the environment. Therefore they need to be recycled. In this work a decomposition method that involves applying a stream of water at very high pressure (to 600MPa) is presented. This method is based on the authors' own patent from 2010 and the results have been provided from two year-long tests and calculations This study includes many diagrams, images and calculations that have been used to develop the discussed method which is competitive for currently used ones.

MOBILE ON-SITE RECYCLING OF METALWORKING FLUIDS

EPA Science Inventory

Product quality, waste reduction, and economic issues were evaluated for a technology designed to recycle metalworking fluids. mulsion-type fluids were tested at two sites and a synthetic fluid was tested at a third site. he specific recycling unit evaluated is based on the techn...

GENERIC VERIFICATION PROTOCOL FOR AQUEOUS CLEANER RECYCLING TECHNOLOGIES

EPA Science Inventory

This generic verification protocol has been structured based on a format developed for ETV-MF projects. This document describes the intended approach and explain plans for testing with respect to areas such as test methodology, procedures, parameters, and instrumentation. Also ...

An exploratory study of lead recovery in lead-acid battery lifecycle in US market: an evidence-based approach.

PubMed

Genaidy, A M; Sequeira, R; Tolaymat, T; Kohler, J; Rinder, M

2008-12-15

This research examines lead recovery and recycling in lead-acid batteries (LAB) which account for 88% of US lead consumption. We explore strategies to maximize lead recovery and recycling in the LAB lifecycle. Currently, there is limited information on recycling rates for LAB in the published literature and is derived from a single source. Therefore, its recycling efforts in the US has been unclear so as to determine the maximum opportunities for metal recovery and recycling in the face of significant demands for LAB particularly in the auto industry. The research utilizes an evidence-based approach to: (1) determine recycling rates for lead recovery in the LAB product lifecycle for the US market; and (2) quantify and identify opportunities where lead recovery and recycling can be improved. A comprehensive electronic search of the published literature was conducted to gather information on different LAB recycling models and actual data used to calculate recycling rates based on product lifecycle for the US market to identify strategies for increasing lead recovery and recycling. The electronic search yielded five models for calculating LAB recycling rates. The description of evidence was documented for each model. Furthermore, an integrated model was developed to identify and quantify the maximum opportunities for lead recovery and recycling. Results showed that recycling rates declined during the period spanning from 1999 to 2006. Opportunities were identified for recovery and recycling of lead in the LAB product lifecycle. One can deduce the following from the analyses undertaken in this report: (1) lead recovery and recycling has been stable between 1999 and 2006; (2) lead consumption has increased at an annual rate of 2.25%, thus, the values derived in this study for opportunities dealing with lead recovery and recycling underestimate the amount of lead in scrap and waste generated; and (3) the opportunities for maximizing lead recovery and recycling are centered on spent batteries left with consumers, mishandled LAB sent to auto wreckers, slag resulting from recycling technology process inefficiencies, and lead lost in municipal waste.

Diaper wars: Chapter six -- technology strikes back

DOE Office of Scientific and Technical Information (OSTI.GOV)

Naquin, D.

1997-10-01

With $1.5 million in funding, including $80,000 from the Israeli Office of the Chief Scientist, Israeli and US investors developed and patented Diapactor, a self-contained unit designed to process 60 used diapers per hour, while reducing volume by 95%. The group introduced the product at WasteExpo `97, held in May in Atlanta. Its end products are pellets of commingled plastic and of cellulose pulp. The machine, about twice the size of the average family washing machine, is produced by Diatec Recycling Technologies USA, Inc. (Agoura Hills, Calif.). Diapers go in at the top of the Diapactor. The machine does themore » rest, opening the diaper, pumping in water, heating the material, and separating it into usable components. Since paper used for personal hygiene products must meet high standards, the resulting pulp is high grade. It can be recycled into new diapers or various paper products, including stationery. Plastic pellets, produced from the diaper`s tape and lining, can be melted down and recycled into a variety of items, including paving tiles, asphalt, and plastic fencing.« less

Silver recovery aqueous techniques from diverse sources: Hydrometallurgy in recycling.

PubMed

Syed, S

2016-04-01

The demand of silver is ever increasing with the advance of the industrialized world, whereas worldwide reserves of high grade silver ores are retreating. However, there exist large stashes of low and lean grade silver ores that are yet to be exploited. The main impression of this work was to draw attention to the most advance technologies in silver recovery and recycling from various sources. The state of the art in recovery of silver from different sources by hydrometallurgical and bio-metallurgical processing and varieties of leaching, cementing, reducing agents, peeling, electro-coagulants, adsorbents, electro-dialysis, solvent extraction, ion exchange resins and bio sorbents are highlighted in this article. It is shown that the major economic driver for recycling of depleted sources is for the recovery of silver. In order to develop an nature-friendly technique for the recovery of silver from diverse sources, a critical comparison of existing technologies is analyzed for both economic viability and environmental impact was made in this amendment and silver ion toxicity is highlighted. Copyright © 2016 Elsevier Ltd. All rights reserved.

Green IT Model for IT Departments in Gulf Cooperation Council (GCC) Organisations

ERIC Educational Resources Information Center

Albahlal, Abdulaziz

2016-01-01

Environmental problems such as climate change, pollution, non-sustainable energy, resource depletion, and recycling Information Technology (IT) devices considered the biggest glitches which are facing developed and developing countries. IT devices have become a critical issue due to the great amount of environmental damage caused by IT companies…

Recovering recyclable materials from shredder residue

NASA Astrophysics Data System (ADS)

Jody, Bassam J.; Daniels, Edward J.; Bonsignore, Patrick V.; Brockmeier, Norman F.

1994-02-01

Each year, about 11 million tons of metals are recovered in the United States from about 10 million discarded automobiles. The recovered metals account for about 75 percent of the total weight of the discarded vehicles. The balance of the material, known as shredder residue, amounts to about three million tons annually and is currently landfilled. The residue contains a diversity of potentially recyclable materials, including polyurethane foams, iron oxides, and certain thermoplastics. This article discusses a process under development at Argonne National Laboratory to separate and recover the recyclable materials from this waste stream. The process consists essentially of two stages. First, a physical separation is used to recover the foams and the metal oxides, followed by a chemical process to extract certain thermoplastics. The status of the technology and the process economics are reviewed here.

Prioritizing material recovery for end-of-life printed circuit boards

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang Xue, E-mail: xxw6590@rit.edu; Gaustad, Gabrielle, E-mail: gabrielle.gaustad@rit.edu

2012-10-15

Highlights: Black-Right-Pointing-Pointer Material recovery driven by composition, choice of ranking, and weighting. Black-Right-Pointing-Pointer Economic potential for new recycling technologies quantified for several metrics. Black-Right-Pointing-Pointer Indicators developed for materials incurring high eco-toxicity costs. Black-Right-Pointing-Pointer Methodology useful for a variety of stakeholders, particularly policy-makers. - Abstract: The increasing growth in generation of electronic waste (e-waste) motivates a variety of waste reduction research. Printed circuit boards (PCBs) are an important sub-set of the overall e-waste stream due to the high value of the materials contained within them and potential toxicity. This work explores several environmental and economic metrics for prioritizing the recovery ofmore » materials from end-of-life PCBs. A weighted sum model is used to investigate the trade-offs among economic value, energy saving potentials, and eco-toxicity. Results show that given equal weights for these three sustainability criteria gold has the highest recovery priority, followed by copper, palladium, aluminum, tin, lead, platinum, nickel, zinc, and silver. However, recovery priority will change significantly due to variation in the composition of PCBs, choice of ranking metrics, and weighting factors when scoring multiple metrics. These results can be used by waste management decision-makers to quantify the value and environmental savings potential for recycling technology development and infrastructure. They can also be extended by policy-makers to inform possible penalties for land-filling PCBs or exporting to the informal recycling sector. The importance of weighting factors when examining recovery trade-offs, particularly for policies regarding PCB collection and recycling are explored further.« less

Resource recycling technique of abandoned TNT-RDX-AL mixed explosive

NASA Astrophysics Data System (ADS)

Chen, Siyang; Ding, Yukui

2017-08-01

TNT-RDX-AL mixed explosive is a kind of high energy mixed explosive. It has the detonation characteristics even when reaching the scrapping standard. Inappropriate disposal often causes serious accident. Employing the resource recycling technique, the abandoned TNT-RDX-AL mixed explosive can be recycled. This paper summarized the progress of recycling of abandoned mixed explosive. What's more, three kinds of technological process of resource recycling abandoned TNT-RDX-AL mixed explosives are introduced. The author analysis of the current recovery processes and provided a reference for the recycling of the other same type explosive.

Argonne National Laboratory's Recycling Pilot Plant

ScienceCinema

Spangenberger, Jeff; Jody, Sam

2018-05-30

Argonne has a Recycling Pilot Plant designed to save the non-metal portions of junked cars. Here, program managers demonstrate how plastic shredder residue can be recycled. (Currently these automotive leftovers are sent to landfills. For more information, visit Argonne's Transportation Technology R&D Center Web site at http://www.transportation.anl.gov.

[Research on resources chemistry of Chinese medicinal materials and resources recycling utilization ways and goals and tasks].

PubMed

Duan, Jin-ao; Su, Shu-lan; Guo, Sheng; Jiang, Shu; Liu, Pei; Yan, Hui; Qian, Da-wei; Zhu, Hua-xu; Tang, Yu-ping; Wu, Qi-nan

2015-09-01

The objects of research on the resources chemistry of Chinese medicinal materials (RCCMM) are promotion of efficient production, rational utilization and improving quality of CMM and natural products. The development of TCM cause depends on the efficient utilization and sustainable development of CMM, hinges on the technologies and methods for using and discovering medicinal biological resources, stand or fall on the extension of industy chains, detailed utilizaion of resource chemical components by multi-way, multi-level. All of these may help to the recycling utilization and sound development of RCMM. In this article, five respects were discussed to the RCCMM researches and resources recycling utilization ways and goals and tasks. First, based on the principle of resource scarcity, discovering or replacing CMM resources, protecting the rare or endangered species or resources. Second, based on the multifunctionality of CMM, realizing the value-added and value compensation, and promoting the utilization efficiency through systermatic and detailed exploitation and utilization. Third, based on the resource conservation and environment-friendly, reducing raw material consumption, lowering cost, promoting recycling utilization and elevating utilization efficiency. Fourth, based on the stratege of turning harm into good, using the invasive alien biological resources by multi-ways and enriching the medicial resources. Fifth, based on the method of structure modification of chemical components, exploring and enhancing the utility value of resouces chemical substances. These data should provide references and attention for improving the utilization efficiency, promoting the development of recycling economy, and changing the mode of economic growth of agriculture and industry of CMM fundamentally.

Technological, Economic, and Environmental Optimization of Aluminum Recycling

NASA Astrophysics Data System (ADS)

Ioana, Adrian; Semenescu, Augustin

2013-08-01

The four strategic directions (referring to the entire life cycle of aluminum) are as follows: production, primary use, recycling, and reuse. Thus, in this work, the following are analyzed and optimized: reducing greenhouse gas emissions from aluminum production, increasing energy efficiency in aluminum production, maximizing used-product collection, recycling, and reusing. According to the energetic balance at the gaseous environment level, the conductive transfer model is also analyzed through the finished elements method. Several principles of modeling and optimization are presented and analyzed: the principle of analogy, the principle of concepts, and the principle of hierarchization. Based on these principles, an original diagram model is designed together with the corresponding logic diagram. This article also presents and analyzes the main benefits of aluminum recycling and reuse. Recycling and reuse of aluminum have the main advantage that it requires only about 5% of energy consumed to produce it from bauxite. The aluminum recycling and production process causes the emission of pollutants such as dioxides and furans, hydrogen chloride, and particulate matter. To control these emissions, aluminum recyclers are required to comply with the National Emission Standards for Hazardous Air Pollutants for Secondary Aluminum Production. The results of technological, economic, and ecological optimization of aluminum recycling are based on the criteria function's evaluation in the modeling system.

Theoretical Analysis and Experimental Study on the Coating Removal from Passenger-Vehicle Plastics for Recycling by Using Water Jet Technology

NASA Astrophysics Data System (ADS)

Zhang, Hongshen; Chen, Ming

2015-11-01

The recovery and utilization of automotive plastics are a global concern because of the increasing number of end-of-life vehicles. In-depth studies on technologies for the removal of coatings from automotive plastics can contribute to the high value-added levels of the recycling and utilization of automotive plastic. The liquid waste generated by removing chemical paint by using traditional methods is difficult to handle and readily produces secondary pollution. Therefore, new, clean, and highly efficient techniques of paint removal must be developed. In this article, a method of coating removal from passenger-vehicle plastics was generated based on high-pressure water jet technology to facilitate the recycling of these plastics. The established technology was theoretically analyzed, numerically simulated, and experimentally studied. The high-pressure water jet equipment for the removal of automotive-plastic coatings was constructed through research and testing, and the detailed experiments on coating removal rate were performed by using this equipment. The results showed that high-pressure water jet technology can effectively remove coatings on the surfaces of passenger-vehicle plastics. The research also revealed that the coating removal rate increased as jet pressure ( P) increased and then decreased when jet moving speed ( Vn) increased. The rate decreased as the distance from nozzle to work piece ( S nw ) and the nozzle angle ( Φ) increased. The mathematical model for the rate of removal of coatings from bumper surfaces by water jet was derived based on the experiment data and can effectively predict coating removal rate under different operating conditions.

Innovative technologies for asbestos removal, treatment and recycle

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bossart, S.J.; Kasper, K.M.

This paper will provide an overview of the Office of Science and Technology`s Decontamination and Decommissioning (D & D) Focus Area`s investment in development and demonstration of innovative technologies for asbestos treatment, removal and recycle. The paper will cover the market opportunities for asbestos abatement, major regulations covering asbestos abatement, baseline technologies used by DOE for removal of asbestos, asbestos-related technology needs submitted by DOE`s Site Technology Coordinating Groups, and asbestos development and demonstration projects supported by the D & D Focus Area and other organizations. Based on the Environmental Management Integrated Database, there are about five million cubic feetmore » of asbestos within the DOE Weapons Complex that will be abated by 2030. DOE has three main forms of asbestos: transite used in building construction, thermal pipe insulation, and floor tile. The D & D Focus Area has or is supporting three projects in asbestos removal, and three projects on destruction of asbestos fibers by chemical and thermal treatment. In asbestos removal, the D & D Focus Area is investigating a robot which removes asbestos insulation from pipes; a laser cutting technology which melts asbestos fibers while cutting insulated pipes; and a vacuum system which removes thermal insulation sandwiched between panels of transite. For destruction of asbestos fibers, the D & D Focus Area is supporting development and demonstration of a trailer-mounted process which destroys asbestos fibers by a combination of thermal and chemical treatment; a three-step process which removes organic and radioactive contaminants from the asbestos prior to decomposing the asbestos fibers by acid attack; and an in situ chemical treatment process to convert asbestos fibers into a non-regulated material.« less

Industrial waste recycling strategies optimization problem: mixed integer programming model and heuristics

NASA Astrophysics Data System (ADS)

Tang, Jiafu; Liu, Yang; Fung, Richard; Luo, Xinggang

2008-12-01

Manufacturers have a legal accountability to deal with industrial waste generated from their production processes in order to avoid pollution. Along with advances in waste recovery techniques, manufacturers may adopt various recycling strategies in dealing with industrial waste. With reuse strategies and technologies, byproducts or wastes will be returned to production processes in the iron and steel industry, and some waste can be recycled back to base material for reuse in other industries. This article focuses on a recovery strategies optimization problem for a typical class of industrial waste recycling process in order to maximize profit. There are multiple strategies for waste recycling available to generate multiple byproducts; these byproducts are then further transformed into several types of chemical products via different production patterns. A mixed integer programming model is developed to determine which recycling strategy and which production pattern should be selected with what quantity of chemical products corresponding to this strategy and pattern in order to yield maximum marginal profits. The sales profits of chemical products and the set-up costs of these strategies, patterns and operation costs of production are considered. A simulated annealing (SA) based heuristic algorithm is developed to solve the problem. Finally, an experiment is designed to verify the effectiveness and feasibility of the proposed method. By comparing a single strategy to multiple strategies in an example, it is shown that the total sales profit of chemical products can be increased by around 25% through the simultaneous use of multiple strategies. This illustrates the superiority of combinatorial multiple strategies. Furthermore, the effects of the model parameters on profit are discussed to help manufacturers organize their waste recycling network.

Developing the Water Supply System for Travel to Mars

NASA Technical Reports Server (NTRS)

Jones, Harry W.; Fisher, John W.; Delzeit, Lance D.; Flynn, Michael T.; Kliss, Mark H.

2016-01-01

What water supply method should be used on a trip to Mars? Two alternate approaches are using fuel cell and stored water, as was done for short missions such as Apollo and the Space Shuttle, or recycling most of the water, as on long missions including the International Space Station (ISS). Stored water is inexpensive for brief missions but its launch mass and cost become very large for long missions. Recycling systems have much lower total mass and cost for long missions, but they have high development cost and are more expensive to operate than storage. A Mars transit mission would have an intermediate duration of about 450 days out and back. Since Mars transit is about ten times longer than a brief mission but probably less than one-tenth as long as ISS, it is not clear if stored or recycled water would be best. Recycling system design is complicated because water is used for different purposes, drinking, food preparation, washing, and flushing the urinal, and because wastewater has different forms, humidity condensate, dirty wash water, and urine and flush water. The uses have different requirements and the wastewater resources have different contaminants and processing requirements. The most cost-effective water supply system may recycle some wastewater sources and also provide safety reserve water from storage. Different water supply technologies are compared using mass, cost, reliability, and other factors.

Feedstock recycling program gets go ahead

DOE Office of Scientific and Technical Information (OSTI.GOV)

Layman, P.

1994-03-28

Feedstock recycling--recycling mixed plastics wastes back into chemical feedstocks such as olefins and naphtha--has received a commercial go ahead in Germany. DKR--Deutsche Kunstsoff recycling, a subsidiary of a commercial company, Duales System Deutschland, responsible for recycling packaging wastes in Germany--has issued three contracts to companies with feedstock recycling technology to convert to liquid feedstocks a total of some 500,000 metric tons per year of mixed plastics packaging wastes by 1996. DKR has also pledged to discontinue exports of used plastics packaging to foreign countries by that date. The three contracts go to a consortium between BASF and OTTO Kunststoff service,more » of Dossenheim; the oil and chemical producer Veba; and the electric power utilities company RWE. DKR's current processing costs are about $1,765 per ton of wastes. That total includes all costs for collecting, sorting, cleaning, and transporting the wastes. In its bid, the BASF-OTTO consortium envisioned a fee of about $190 per ton. That fee, says Niess, was determined by looking at BASF's and OTTO's costs, offset by the savings in raw materials BASF would be making as its technology converts mixed plastics wastes to a mixture of naphtha, aromatics, and oils, all of which can be used in BASF's processes in Ludwigshafen. And because BASF's technology requires no presorting or cleaning before it gets the wastes, the process will trim DKR's costs significantly.« less

Recycle technology for recovering resources and products from waste printed circuit boards.

PubMed

Li, Jia; Lu, Hongzhou; Guo, Jie; Xu, Zhenming; Zhou, Yaohe

2007-03-15

The printed circuit board (PCB) contains nearly 28% metals that are abundant non-ferrous metals such as Cu, Al, Sn, etc. The purity of precious metals in PCBs is more than 10 times higher than that of rich-content minerals. Therefore, recycling of PCBs is an important subject not only from the treatment of waste but also from the recovery of valuable materials. Chemical and mechanical methods are two traditional recycling processes for waste PCBs. However, the prospect of chemical methods will be limited since the emission of toxic liquid or gas brings secondary pollution to the environment during the process. Mechanical processes, such as shape separation, jigging, density-based separation, and electrostatic separation have been widely utilized in the recycling industry. But, recycling of waste PCBs is only beginning. In this study, a total of 400 kg of waste PCBs was processed by a recycle technology without negative impact to the environment. The technology contained mechanical two-step crushing, corona electrostatic separating, and recovery. The results indicated that (i) two-step crushing was an effect process to strip metals from base plates completely; (ii) the size of particles between 0.6 and 1.2 mm was suitable for corona electrostatic separating during industrial application; and (iii) the nonmetal of waste PCBs attained 80% weight of a kind of nonmetallic plate that expanded the applying prospect of waste nonmetallic materials.

The lifecycle of silver in the United States in 2009

USGS Publications Warehouse

Goonan, Thomas G.

2014-01-01

Because silver is highly sought after for its properties, which make it eminently suitable for new technology applications, a clear understanding of the flow of materials in the economy, the historical context, and trends for the future can help project the future of silver in the economy of the United States. Silver has many properties that are desired in today’s economy. It has superior electrical and heat conductivity, chemical stability, high-temperature strength, malleability, and other characteristics that make it important in high-tech electronic and other industrial applications. Because it is relatively scarce as a natural resource and is easily coined, silver historically has been an important monetary metal. As knowledge of silver chemistry has increased, many industrial end uses have been developed. This study reviews the flows of silver into various end uses and examines the nature of the end use with respect to the silver properties desired and the ability of the end use to produce recyclable end-of-life materials. For the most part, silver can be profitably recycled, but the recycling activity is helped by tipping fees (fees imposed on scrap generators by scrap collectors for taking the material) for materials that might otherwise be regulated as hazardous wastes. New high-technology applications use silver in nanolevel amounts, leading to a potential for dissipative loss and reduced recycling capability.

PARALLEL MULTIOBJECTIVE EVOLUTIONARY ALGORITHMS FOR WASTE SOLVENT RECYCLING

EPA Science Inventory

Waste solvents are of great concern to the chemical process industries and to the public, and many technologies have been suggested and implemented in the chemical process industries to reduce waste and associated environmental impacts. In this article we have developed a novel p...

SITE DEMONSTRATION BULLETIN: SOIL RECYCLING TREATMENT TRAIN - THE TORONTO HARBOUR COMMISSIONERS

EPA Science Inventory

The Toronto Harbour Commissioners (THC) have developed a soil treatment train designed to treat inorganic and organic contaminants in soils. THC has conducted a large-scale demonstration of these technologies in an attempt to establish that contaminated soils at the Toronto Port...

RECYCLED MATERIALS FOR REPAIR AND REHABILITATION OF AGING CONCRETE STRUCTURES - PHASE I

EPA Science Inventory

Exterior wrapping of concrete columns initially was developed for seismic reinforcement in high-risk areas such as California. As the technology has gained acceptance, it is being considered for use in extending column life, reducing corrosion, and preventing spalling. All ...

TORONTO HARBOUR COMMISSIONERS (THC) SOIL RECYCLE TREATMENT TRAIN - APPLICATIONS ANALYSIS REPORT

EPA Science Inventory

The Toronto Harbour Commissioners (THC) have developed a soil treatment train designed to treat inorganic and organic contaminants in soils. THC has conducted a large-scale demonstration of these technologies in an attempt to establish that contaminated soils at the Toronto Port ...

A historical perspective of Global Warming Potential from Municipal Solid Waste Management.

PubMed

Habib, Komal; Schmidt, Jannick H; Christensen, Per

2013-09-01

The Municipal Solid Waste Management (MSWM) sector has developed considerably during the past century, paving the way for maximum resource (materials and energy) recovery and minimising environmental impacts such as global warming associated with it. The current study is assessing the historical development of MSWM in the municipality of Aalborg, Denmark throughout the period of 1970 to 2010, and its implications regarding Global Warming Potential (GWP(100)), using the Life Cycle Assessment (LCA) approach. Historical data regarding MSW composition, and different treatment technologies such as incineration, recycling and composting has been used in order to perform the analysis. The LCA results show a continuous improvement in environmental performance of MSWM from 1970 to 2010 mainly due to the changes in treatment options, improved efficiency of various treatment technologies and increasing focus on recycling, resulting in a shift from net emission of 618 kg CO(2)-eq.tonne(-1) to net saving of 670 kg CO(2)-eq.tonne(-1) of MSWM. Copyright © 2013 Elsevier Ltd. All rights reserved.

The New Global Responsibilities of Engineers Create Challenges for Engineering Education

ERIC Educational Resources Information Center

Fuchs, Willi

2012-01-01

Modern societies aim to solve the global challenges of the 21st century with sustainable solutions such as resource efficiency, use of renewable energy sources and recycling. Engineers are called upon to create the cutting edge technological solutions that can help to address these challenges. In developed as well as in developing countries,…

Forestry implications of agricultural short-rotation woody crops in the USA

Treesearch

Peter J. Ince; Alexander N. Moiseyev

2002-01-01

The purpose of this chapter is to discuss forestry implications of SRWC based on an economic analysis. As with the development of paper recycling, anticipating forestry implications of agricultural SRWC will depend in part on anticipating market conditions and economic impacts of technological developments. This chapter presents an analytic framework and market outlook...

Federal Research Action Plan (FRAP) on Recycled Tire Crumb Used on Playing Fields and Playgrounds (5th Annual Recycled Rubber Products Technology Conference)

EPA Science Inventory

This presentation provides an overview and status update of the Federal Research Action Plan (FRAP) on Recycled Tire Crumb Used on Playing Fields and Playgrounds. The presentation includes information on Federal research activities, stakeholder engagement, other studies, and the ...

On the Development of Hydrogen Isotope Extraction Technologies for a Full LiMIT-Style PFC Liquid Lithium Loop

NASA Astrophysics Data System (ADS)

Christenson, Michael; Szott, Matthew; Stemmley, Steven; Mettler, Jeremy; Wendeborn, John; Moynihan, Cody; Ahn, Chisung; Andruczyk, Daniel; Ruzic, David

2017-10-01

Lithium has proven over numerous studies to improve core confinement, allowing access to operational regimes previously unattainable when using solid, high-Z divertor and limiter modules in magnetic confinement devices. Lithium readily absorbs fuel species, and while this is advantageous, it is also detrimental with regards to tritium inventory and safety concerns. As such, extraction technologies for the recovery of hydrogenic isotopes captured by lithium require development and testing in the context of a larger lithium loop recycling system. Proposed reclamation technologies at the University of Illinois at Urbana-Champaign (UIUC) will take advantage of the thermophysical properties of the lithium-hydrogen-lithium hydride system as the driving force for recovery. Previous work done at UIUC indicates that hydrogen release from pure lithium hydride reaches a maximum of 7 x 1018 s-1 at 665 °C. While this recovery rate is appreciable, reactor-scale scenarios will require isotope recycling to happen on an even faster timescale. The ratio of isotope dissolution to hydride precipitate formation must therefore be determined, along with the energy needed to recoup trapped hydrogen isotopes. Extraction technologies for use with a LiMIT-style loop system will be discussed and results will be presented. DOE/ALPS DE-FG02-99ER54515.

Methods of silver recovery from radiographs - comparative study

NASA Astrophysics Data System (ADS)

Canda, L. R.; Ardelean, E.; Hepuţ, T.

2018-01-01

Management and recovery of waste are activities with multiple impacts: technologically (by using waste on current production flows, thus replacing poor raw materials), economically (can substantially reduce manufacturing costs by recycling waste), social (by creating new jobs where it is necessary to process the waste in a form more suited to technological flows) and ecologically (by removing waste that is currently produced or already stored - but poses a threat to the health of the population and / or to the environment). This is also the case for medical waste, for example radiographs, which are currently produced in large quantities, for which replacement solutions are sought, but are currently stored by archiving in hospital units. The paper presents two methods used for this kind of waste management, the result being the recovery of silver, material with applications and with increasing price, but also the proper disposal of the polymeric support. This analysis aims at developing a more efficient recycling technology for medical radiographs.

Progress in the Development of Direct Osmotic Concentration Wastewater Recovery Process for Advanced Life Support Systems

NASA Technical Reports Server (NTRS)

Cath, Tzahi Y.; Adams, Dean V.; Childress, Amy; Gormly, Sherwin; Flynn, Michael

2005-01-01

Direct osmotic concentration (DOC) has been identified as a high potential technology for recycling of wastewater to drinking water in advanced life support (ALS) systems. As a result the DOC process has been selected for a NASA Rapid Technology Development Team (RTDT) effort. The existing prototype system has been developed to a Technology Readiness Level (TRL) 3. The current project focuses on advancing the development of this technology from TRL 3 to TRL 6 (appropriate for human rated testing). A new prototype of a DOC system is been designed and fabricated that addresses the deficiencies encountered during the testing of the original system and allowing the new prototype to achieve TRL 6. Background information is provided about the technologies investigated and their capabilities, results from preliminary tests, and the milestones plan and activities for the RTDT program intended to develop a second generation prototype of the DOC system.

Environmental friendly technology for aluminum electrolytic capacitors recycling from waste printed circuit boards.

PubMed

Wang, Jianbo; Xu, Zhenming

2017-03-15

up to now, the recycling of e-waste should be developed towards more depth and refinement to promote industrial production of e-waste resource recovery. in the present study, the recycling of aluminum electrolytic capacitors (AECs) from waste printed circuit boards (WPCBs) is focused on. First of all, AECs are disassembled from WPCBs by a self-designed machine; meanwhile, the disassembled AECs are subjected to an integrated process, involving heating treatment, crushing, sieving, and magnetic separating, to recover aluminum and iron; finally, the off-gas and residue generated during the aforementioned processes are analyzed to evaluate environmental risks. The results indicate that 96.52% and 98.68% of aluminum and iron, respectively, can be recovered from AECs under the optimal condition. The off-gas generated during the process is mainly composed of elements of C, H, and O, indicating that the off-gas is non-toxic and could be re-utilized as clean energy source. The residue according with toxicity characteristics leaching standard can be landfilled safely in sanitary landfill site. The present study provides an environmentally friendly and industrial application potential strategy to recycle AECs to promote e-waste recycling industry. Copyright © 2016 Elsevier B.V. All rights reserved.

Long-term strategies for increased recycling of automotive aluminum and its alloying elements.

PubMed

Løvik, Amund N; Modaresi, Roja; Müller, Daniel B

2014-04-15

Aluminum recycling currently occurs in a cascading fashion, where some alloys, used in a limited number of applications, absorb most of the end-of-life scrap. An expected increase in scrap supply in coming decades necessitates restructuring of the aluminum cycle to open up new recycling paths for alloys and avoid a potential scrap surplus. This paper explores various interventions in end-of-life management and recycling of automotive aluminum, using a dynamic substance flow analysis model of aluminum and its alloying elements with resolution on component and alloy level (vehicle-component-alloy-element model). It was found that increased component dismantling before vehicle shredding can be an effective, so far underestimated, intervention in the medium term, especially if combined with development of safety-relevant components such as wheels from secondary material. In the long term, automatic alloy sorting technologies are most likely required, but could at the same time reduce the need for magnesium removal in refining. Cooperation between the primary and secondary aluminum industries, the automotive industry, and end-of-life vehicle dismantlers is therefore essential to ensure continued recycling of automotive aluminum and its alloying elements.

Ash characterization in laboratory-scale oxy-coal combustor

EPA Science Inventory

Oxygen enriched coal (oxy-coal) combustion is a developing technology. During oxy-coal combustion, combustion air is separated and the coal is burned in a mixture of oxygen and recycled flue gas. The resulting effluent must be further processed before the C02 can be compressed, t...

Application of NASA's Advanced Life Support Technologies for Waste Treatment, Water Purification and Recycle, and Food Production in Polar Regions

NASA Technical Reports Server (NTRS)

Bubenheim, David L.; Lewis, Carol E.; Covington, M. Alan (Technical Monitor)

1995-01-01

NASA's advanced life support technologies are being combined with Arctic science and engineering knowledge to address the unique needs of the remote communities of Alaska through the Advanced Life Systems for Extreme Environments (ALSEE) project. ALSEE is a collaborative effort involving NASA, the State of Alaska, the University of Alaska, the North Slope Borough of Alaska, and the National Science Foundation (NSF). The focus is a major issue in the state of Alaska and other areas of the Circumpolar North, the health and welfare of its people, their lives and the subsistence lifestyle in remote communities, economic opportunity, and care for the environment. The project primarily provides treatment and reduction of waste, purification and recycling of water. and production of food. A testbed is being established to demonstrate the technologies which will enable safe, healthy, and autonomous function of remote communities and to establish the base for commercial development of the resulting technology into new industries. The challenge is to implement the technological capabilities in a manner compatible with the social and economic structures of the native communities, the state, and the commercial sector. Additional information is contained in the original extended abstract.

Guide to conducting state recycling economic development finance workshops

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-12-31

The objective of this project was to demonstrate a two-pronged program for educating economic development and recycling officials about recycling business development opportunities. The project consisted of conducting a stat recycling finance workshop in each of three Northeastern states, as well as recycling economic development finance training program for the region`s economic development and recycling officials. The goal of the project is to facilitate the expansion of recycling businesses in the Northeast. The guide details seven steps to conducting a recycling economic development finance workshop: (1) establish a workshop planning committee, (2) select the target audience, (3) develop the workshopmore » message, (4) identify the message deliverer, (5) choose workshop topics and structure the workshop, (6) attract the audience, and (7) Conduct follow-up. In the process of planning and conducting the three state workshops for this project, NERC learned several important lessons: (1) Conduct workshops that are specific to the recycling and economic development programs in the state. (2) Include recycling business case studies on the workshop agenda. (3) Enhance the workshop with recycling economic development finance training. Develop a comprehensive marketing strategy.« less

An integrated decision support system for wastewater nutrient recovery and recycling to agriculture

NASA Astrophysics Data System (ADS)

Roy, E. D.; Bomeisl, L.; Cornbrooks, P.; Mo, W.

2017-12-01

Nutrient recovery and recycling has become a key research topic within the wastewater engineering and nutrient management communities. Several technologies now exist that can effectively capture nutrients from wastewater, and innovation in this area continues to be an important research pursuit. However, practical nutrient recycling solutions require more than capable nutrient capture technologies. We also need to understand the role that wastewater nutrient recovery and recycling can play within broader nutrient management schemes at the landscape level, including important interactions at the nexus of food, energy, and water. We are developing an integrated decision support system that combines wastewater treatment data, agricultural data, spatial nutrient balance modeling, life cycle assessment, stakeholder knowledge, and multi-criteria decision making. Our goals are to: (1) help guide design decisions related to the implementation of sustainable nutrient recovery technology, (2) support innovations in watershed nutrient management that operate at the interface of the built environment and agriculture, and (3) aid efforts to protect aquatic ecosystems while supporting human welfare in a circular nutrient economy. These goals will be realized partly through the assessment of plausible alternative scenarios for the future. In this presentation, we will describe the tool and focus on nutrient balance results for the New England region. These results illustrate that both centralized and decentralized wastewater nutrient recovery schemes have potential to transform nutrient flows in many New England watersheds, diverting wastewater N and P away from aquatic ecosystems and toward local or regional agricultural soils where they can offset a substantial percentage of imported fertilizer. We will also highlight feasibility criteria and next steps to integrate stakeholder knowledge, economics, and life cycle assessment into the tool.

Management strategies on the industrialization road of state-of-the-art technologies for e-waste recycling: the case study of electrostatic separation--a review.

PubMed

Xue, Mianqiang; Li, Jia; Xu, Zhenming

2013-02-01

Electronic waste (e-waste) management is pressing as global production has increased significantly in the past few years and is rising continuously at a fast rate. Many countries are facing hazardous e-waste mountains, most of which are disposed of by backyard recyclers, creating serious threats to public health and ecosystems. Industrialization of state-of-the-art recycling technologies is imperative to enhance the comprehensive utilization of resources and to protect the environment. This article aims to provide an overview of management strategies solving the crucial problems during the process of industrialization. A typical case study of electrostatic separation for recycling waste printed circuit boards was discussed in terms of parameters optimization, materials flow control, noise assessment, risk assessment, economic evaluation and social benefits analysis. The comprehensive view provided by the review could be helpful to the progress of the e-waste recycling industry.

Design and Implementation of a Hall Effect Sensor Array Applied to Recycling Hard Drive Magnets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kisner, Roger; Lenarduzzi, Roberto; Killough, Stephen M

Rare earths are an important resource for many electronic components and technologies. Examples abound including Neodymium magnets used in mobile devices and computer hard drives (HDDs), and a variety of renewable energy technologies (e.g., wind turbines). Approximately 21,000 metric tons of Neodymium is processed annually with less than 1% being recycled. An economic system to assist in the recycling of magnet material from post-consumer goods, such as Neodymium Iron Boron magnets commonly found in hard drives is presented. A central component of this recycling measurement system uses an array of 128 Hall Effect sensors arranged in two columns to detectmore » the magnetic flux lines orthogonal to the HDD. Results of using the system to scan planar shaped objects such as hard drives to identify and spatially locate rare-earth magnets for removal and recycling from HDDs are presented. Applications of the sensor array in other identification and localization of magnetic components and assemblies will be presented.« less

CELSS experiment model and design concept of gas recycle system

NASA Technical Reports Server (NTRS)

Nitta, K.; Oguchi, M.; Kanda, S.

1986-01-01

In order to prolong the duration of manned missions around the Earth and to expand the human existing region from the Earth to other planets such as a Lunar Base or a manned Mars flight mission, the controlled ecological life support system (CELSS) becomes an essential factor of the future technology to be developed through utilization of space station. The preliminary system engineering and integration efforts regarding CELSS have been carried out by the Japanese CELSS concept study group for clarifying the feasibility of hardware development for Space station experiments and for getting the time phased mission sets after FY 1992. The results of these studies are briefly summarized and the design and utilization methods of a Gas Recycle System for CELSS experiments are discussed.

A review of mechanochemistry applications in waste management.

PubMed

Guo, Xiuying; Xiang, Dong; Duan, Guanghong; Mou, Peng

2010-01-01

Mechanochemistry is defined to describe the chemical and physicochemical transformation of substances during the aggregation caused by the mechanical energy. Mechanochemical technology has several advantages, such as simple process, ecological safety and the possibility of obtaining a product in the metastable state. It potentially has a prospective application in pollution remediation and waste management. Therefore, this paper aims to give an overall review of the mechanochemistry applications in waste management and the related mechanisms. Based on our study, the modification of fly ash and asbestos-containing wastes (ACWs) can be achieved by mechanochemical technology. Waste metal oxides can be transformed into easily recyclable sulfide by mechanochemical sulfidization. Besides, the waste plastics and rubbers, which are usually very difficult to be recycled, can also be recycled by mechanochemical technology.

Economic and policy instrument analyses in support of the scrap tire recycling program in Taiwan.

PubMed

Chang, Ni-Bin

2008-02-01

Understanding the cost-effectiveness and the role of economic and policy instruments, such as the combined product tax-recycling subsidy scheme or a tradable permit, for scrap tire recycling has been of crucial importance in a market-oriented environmental management system. Promoting product (tire) stewardship on one hand and improving incentive-based recycling policy on the other hand requires a comprehensive analysis of the interfaces and interactions in the nexus of economic impacts, environmental management, environmental valuation, and cost-benefit analysis. This paper presents an assessment of the interfaces and interactions between the implementation of policy instruments and its associated economic evaluation for sustaining a scrap tire recycling program in Taiwan during the era of the strong economic growth of the late 1990s. It begins with an introduction of the management of the co-evolution between technology metrics of scrap tire recycling and organizational changes for meeting the managerial goals island-wide during the 1990s. The database collected and used for such analysis covers 17 major tire recycling firms and 10 major tire manufacturers at that time. With estimates of scrap tire generation and possible scale of subsidy with respect to differing tire recycling technologies applied, economic analysis eventually leads to identify the associated levels of product tax with respect to various sizes of new tires. It particularly demonstrates a broad perspective of how an integrated econometric and engineering economic analysis can be conducted to assist in implementing policy instruments for scrap tire management. Research findings indicate that different subsidy settings for collection, processing, and end use of scrap tires should be configured to ameliorate the overall managerial effectiveness. Removing the existing boundaries between designated service districts could strengthen the competitiveness of scrap tires recycling industry, helping to reduce the required levels of product tax and subsidy. With such initial breakthroughs at hand to handle the complexity of scrap tire recycling technologies, there remains unique management and policy avenues left to explore if a multi-dimensional solution is to be successful in the long run.

GHG emission factors developed for the recycling and composting of municipal waste in South African municipalities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Friedrich, Elena, E-mail: Friedriche@ukzn.ac.za; Trois, Cristina

2013-11-15

Highlights: • GHG emission factors for local recycling of municipal waste are presented. • GHG emission factors for two composting technologies for garden waste are included. • Local GHG emission factors were compared to international ones and discussed. • Uncertainties and limitations are presented and areas for new research highlighted. - Abstract: GHG (greenhouse gas) emission factors for waste management are increasingly used, but such factors are very scarce for developing countries. This paper shows how such factors have been developed for the recycling of glass, metals (Al and Fe), plastics and paper from municipal solid waste, as well asmore » for the composting of garden refuse in South Africa. The emission factors developed for the different recyclables in the country show savings varying from −290 kg CO{sub 2} e (glass) to −19 111 kg CO{sub 2} e (metals – Al) per tonne of recyclable. They also show that there is variability, with energy intensive materials like metals having higher GHG savings in South Africa as compared to other countries. This underlines the interrelation of the waste management system of a country/region with other systems, in particular with energy generation, which in South Africa, is heavily reliant on coal. This study also shows that composting of garden waste is a net GHG emitter, releasing 172 and 186 kg CO{sub 2} e per tonne of wet garden waste for aerated dome composting and turned windrow composting, respectively. The paper concludes that these emission factors are facilitating GHG emissions modelling for waste management in South Africa and enabling local municipalities to identify best practice in this regard.« less

Performance Testing of the Vapor Phase Catalytic Ammonia Removal Engineering Development Unit

NASA Technical Reports Server (NTRS)

Flynn, Michael; Tleimat, Maher; Nalette, Tim; Quinn, Gregory

2005-01-01

This paper describes the results of performance testing of the Vapor Phase Catalytic Ammonia Removal (VPCAR) technology. The VPCAR technology is currently being developed by NASA as a Mars transit vehicle water recycling system. NASA has recently completed-a grant-to develop a next generation VPCAR system. This grant concluded with the shipment of the final deliverable to NASA on 8/31/03. This paper presents the results of mass, power, volume, and acoustic measurements for the delivered system. Product water purity analysis for a Mars transit mission and a simulated planetary base wastewater ersatz are also provided.

Triboelectrostatic separation for granular plastic waste recycling: a review.

PubMed

Wu, Guiqing; Li, Jia; Xu, Zhenming

2013-03-01

The world's plastic consumption has increased incredibly in recent decades, generating more and more plastic waste, which makes it a great public concern. Recycling is the best treatment for plastic waste since it cannot only reduce the waste but also reduce the consumption of oil for producing new virgin plastic. Mechanical recycling is recommended for plastic waste to avoid the loss of its virgin value. As a mechanical separation technology, triboelectrostatic separation utilizes the difference between surface properties of different materials to get them oppositely charged, deflected in the electric field and separately collected. It has advantages such as high efficiency, low cost, no concern of water disposal or secondary pollution and a relatively wide processing range of particle size especially suitable for the granular plastic waste. The process of triboelectrostatic separation for plastic waste is reviewed in this paper. Different devices have been developed and proven to be effective for separation of plastic waste. The influence factors are also discussed. It can be concluded that the triboelectrostatic separation of plastic waste is a promising technology. However, more research is required before it can be widely applied in industry. Copyright © 2012 Elsevier Ltd. All rights reserved.

End-of-Life in the railway sector: Analysis of recyclability and recoverability for different vehicle case studies.

PubMed

Delogu, Massimo; Del Pero, Francesco; Berzi, Lorenzo; Pierini, Marco; Bonaffini, Davide

2017-02-01

The railway system represents one of the most resource-efficient answer to our ever-growing demand for transport service and the development trends for the following years forecast a substantial increase in this sector. Considering the European Union, rolling stock realizes a significant share of both goods and passengers carriage while it is responsible for a derisory quota of environmental impact and energy consumption involved by transportation. Contrary to the low environmental impact, the amount of End-of-Life (EoL) waste generated by rolling stocks in relation to the number of vehicles is notable, much greater than in the case of road vehicles. As railway vehicles are constituted by many heterogeneous components, the EoL rolling stock is a precious source of materials, whose recycling brings measurable economic benefits and needs to be appropriately debated. The paper presents calculation of recoverability/recyclability rate for different typologies of vehicles representative of railway transport; calculation is performed on the basis of primary data and according to the recyclability and recoverability calculation method issued by UNIFE in the context of Product Category Rules (PCR). The typologies of railway vehicles taken into account are electric metro, diesel commuter train and high-speed electric train. The analysis envisages also to replicate the calculation in case innovative materials and manufacturing technologies are adopted in the construction of car-body structure. Results show that recyclability/recoverability rates are abundantly over the quota of 90% for each one of the three trains, these latter being made in major part of metals that benefit from very efficient recovery processes. The adoption of innovative materials and manufacturing technologies for car-body structure involves a scarce reduction of recyclability and recoverability rates (about 2% and 0.2% respectively) due to the introduction of components and materials characterized by critical dismantlability and low efficiency recovery processes; recoverability results less affected by lightweighting because post-shredding thermal recovery treatments are roughly independent with respect to dismantlability. A sensitivity analysis based on different dismantling scenarios reveals that the effectiveness of dismantling has a moderate influence on recyclability/recoverability rate (the variation does not exceed 3%). The low variability of recyclability/recoverability rate can be explained by the following reasons: predominance of metals in trains material composition, efficiency of metals separation processes close to 100%, post-shredding recycling processes of metals characterized by recovery factors equal to the ones of post-dismantling recycling processes. Copyright © 2016 Elsevier Ltd. All rights reserved.

New insights into polyurethane biodegradation and realistic prospects for the development of a sustainable waste recycling process.

PubMed

Cregut, Mickael; Bedas, M; Durand, M-J; Thouand, G

2013-12-01

Polyurethanes are polymeric plastics that were first used as substitutes for traditional polymers suspected to release volatile organic hazardous substances. The limitless conformations and formulations of polyurethanes enabled their use in a wide variety of applications. Because approximately 10 Mt of polyurethanes is produced each year, environmental concern over their considerable contribution to landfill waste accumulation appeared in the 1990s. To date, no recycling processes allow for the efficient reuse of polyurethane waste due to their high resistance to (a)biotic disturbances. To find alternatives to systematic accumulation or incineration of polyurethanes, a bibliographic analysis was performed on major scientific advances in the polyurethane (bio)degradation field to identify opportunities for the development of new technologies to recondition this material. Until polymers exhibiting oxo- or hydro-biodegradative traits are generated, conventional polyurethanes that are known to be only slightly biodegradable are of great concern. The research focused on polyurethane biodegradation highlights recent attempts to reprocess conventional industrial polyurethanes via microbial or enzymatic degradation. This review describes several wonderful opportunities for the establishment of new processes for polyurethane recycling. Meeting these new challenges could lead to the development of sustainable management processes involving polymer recycling or reuse as environmentally safe options for industries. The ability to upgrade polyurethane wastes to chemical compounds with a higher added value would be especially attractive. © 2013.

FY 2012 Lightweight Materials Annual Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Warren, David C.

2013-04-15

The FY 2012 Annual Progress Report for Lightweight Materials provides a detailed description of the activities and technical accomplishments which focuses on the development and validation of advanced materials and manufacturing technologies to significantly reduce light and heavy duty vehicle weight without compromising other attributes such as safety, performance, recyclability, and cost.

Alternative Fuels Data Center: Biodiesel Fueling Infrastructure Development

Science.gov Websites

Biodiesel Fueling Station Locations by State More Biodiesel Data | All Maps & Data Case Studies Recycled Fuels Help Ensure America's National Parks Stay Green for Another Century More Biodiesel Case Studies | All Case Studies Publications 2016 Vehicle Technologies Market Report Biodiesel Handling and Use Guide

Aggregates from natural and recycled sources; economic assessments for construction applications; a materials flow study

USGS Publications Warehouse

Wilburn, David R.; Goonan, Thomas G.

1998-01-01

Increased amounts of recycled materials are being used to supplement natural aggregates (derived from crushed stone, sand and gravel) in road construction. An understanding of the economics and factors affecting the level of aggregates recycling is useful in estimating the potential for recycling and in assessing the total supply picture of aggregates. This investigation includes a descriptive analysis of the supply sources, technology, costs, incentives, deterrents, and market relationships associated with the production of aggregates.

Trends in the development of industrially assimilated renewable energy: the problem of resource restrictions

NASA Astrophysics Data System (ADS)

Nizhegorodtsev, R. M.; Ratner, S. V.

2016-03-01

An analysis of the dynamics of the development of wind and solar energy and potential resource restrictions of the dissemination of these technologies of energy generation associated with intensive use of rare earth metals and some other mineral resources are presented. The technological prospects of various directions of decisions of the problem of resource restrictions, including escalating of volumes of extraction and production of necessary mineral components, creating substitutes of scarce materials and development of recycling are considered. The bottlenecks of each of the above-mentioned decisions were founded. Conclusions are drawn on the prospects of development of the Russian high-tech sectors of the economy in the context of the most probable decisions of the problem of resource restrictions of wind and solar energy. An increase in extraction and production of rare earth metals and some other materials, stimulation of domestic research and development (R&D) to create the permanent magnets of new types and new technologies of wind-powered generation, and reduction of the resource-demand and technology development of recycling the components of power equipment are the most prospective directions of progress. The innovations in these directions will be in demand on the European, Chinese, and North American markets in the near decades due to the end of the life cycle (approximately 30 years) of wind and solar energy projects started at the turn of the 20th-21st centuries (the beginning of exponential growth in plants). The private investors and relevant regional and federal government agencies can use the qualitative characteristics of the dynamics of industrially assimilated renewable energy to choose the most promising investment orientations in energy projects and selection of the most economically sound development methods of energy and related industries.

Resource Efficient Metal and Material Recycling

NASA Astrophysics Data System (ADS)

Reuter, Markus A.; van Schaik, Antoinette

Metals enable sustainability through their use and their recyclability. However, various factors can affect the Resource Efficiency of Metal Processing and Recycling. Some typical factors that enable Resource Efficiency include and arranged under the drivers of sustainability: Environment (Maximize Resource Efficiency — Energy, Recyclates, Materials, Water, Sludges, Emissions, Land); Economic Feasibility (BAT & Recycling Systems Simulation / Digitalization, Product vis-à-vis Material Centric Recycling); and Social — Licence to Operate (Legislation, consumer, policy, theft, manual labour.). In order to realize this primary production has to be linked systemically with typical actors in the recycling chain such as Original Equipment Manufacturers (OEMs), Recyclers & Collection, Physical separation specialists as well as process metallurgical operations that produce high value metals, compounds and products that recycle back to products. This is best done with deep knowledge of multi-physics, technology, product & system design, process control, market, life cycle management, policy, to name a few. The combination of these will be discussed as Design for Sustainability (DfS) and Design for Recycling (DfR) applications.

Impact Goals of Research and Development Technology on the Business Strategy of NTT's Fiber-to-the-Home Deployment

NASA Astrophysics Data System (ADS)

Kimura, Hideaki

2013-03-01

Huge investment is needed for introducing a fiber-to-the-home system, so research and development strategy is very important. Requirements for fiber-to-the-home systems have been increased because communication systems have been recognized as one of the lifelines along with water, electricity, and gas. Furthermore, low energy consumption and recyclable eco-friendliness are required for products. NTT has been challenged to reduce capital expenditure, reduce operational expenditure, and create new applications for expanding the number of fiber-to-the-home subscribers from the viewpoint of a technological approach, including access infrastructure, fiber, transmission, and wireless technologies. Due to continuous and strategic technological development, the number of NTT's fiber-to-the-home subscribers is now over 17 million.

Lunar Surface Systems Supportability Technology Development Roadmap

NASA Technical Reports Server (NTRS)

Oeftering, Richard C.; Struk, Peter M.; Green, Jennifer L.; Chau, Savio N.; Curell, Philip C.; Dempsey, Cathy A.; Patterson, Linda P.; Robbins, William; Steele, Michael A.; DAnnunzio, Anthony;

Recyclable epoxy resins: An example of green approach for advanced composite applications

NASA Astrophysics Data System (ADS)

Cicala, Gianluca; Rosa, Daniela La; Musarra, Marco; Saccullo, Giuseppe; Banatao, Rey; Pastine, Stefan

2016-05-01

Automotive composite applications are increasingly growing due to demand for lightweight structures to comply to the requirements for fuel reduction. HP-RTM is gaining relevance as one of the preferred production technologies for high volume applications. The BMW i3 life module being a notable example of HP-RTM application. The key aspects of HP-RTM are the short injection times (i.e. less than 1min) and the fast curing of the thermoset resins (i.e. less than 10min). The choice of using thermosets poses relevant issues for their limited recycling options. The standard recycling solution is the incineration but, this solution poses some concerns in terms of global environmental impact. Novel solutions are presented in this work based on the use of recyclable epoxy systems. In our work the results of experimentation carried out by our group with cleavable ammines by Connora Technologies and bioepoxy resins by Entropy Resins will be discussed. The multiple uses of recycled matrices obtained treating the recyclable epoxy resins are discussed in the framework of a "cradle" to "crave" approach. Finally, Life Cycle Assessment (LCA) is used to evaluate the environmental benefits of the proposed approach.

Dross treatment in a rotary arc furnace with graphite electrodes

NASA Astrophysics Data System (ADS)

Drouet, Michel G.; Handfield, My; Meunier, Jean; Laflamme, Claude B.

1994-05-01

Aluminum baths are always covered with a layer of dross resulting from the aluminum surface oxidation. This dross represents 1-10% of the melt and may contain up to 75wt.% aluminum. Since aluminum production is highly energy intensive, dross recycling is very attractive from both energy and economic standpoints. The conventional recycling process using salt rotary furnaces is thermally inefficient and environmentally unacceptable because of the production of salt slags. Hydro-Quebec has developed a new technology using a rotary arc furnace with graphite electrodes. This process provides aluminum recovery rates of 80-90%, using a highly energy efficient, environmentally sound production method.

NASA Centennial Challenge: Three Dimensional (3D) Printed Habitat, Phase 2

NASA Technical Reports Server (NTRS)

Mueller, Robert P.; Roman, Monserrate C.; Kim, Hong S.

2017-01-01

The NASA Centennial Challenges: 3D-Printed Habitat Challenge seeks to develop the fundamental technologies necessary to manufacture an off-world habitat using mission recycled materials andor local indigenous materials. The vision is that autonomous habitat manufacturing machines will someday be deployed to the Moon or Mars to construct shelters for human habitation.NASA and Bradley University, are holding a new US$ 2.5 million competition to design and build a 3-D printed habitat for deep space exploration, including the agencys journey to Mars.The multi-phase 3-D Printed Habitat Challenge, part of NASA's Centennial Challenges program, is designed to advance the additive construction technology needed to create sustainable housing solutions for Earth and beyond.The first phase of the competition ran through Sept. 27, 2015. This phase, a design competition, called on participants to develop state-of-the-art architectural concepts that take advantage of the unique capabilities 3-D printing offers. The top 3 prizes with a prize purse of $40,000 were awarded at the 2015 World Maker Faire in New York.The second phase of the competition is called the Structural Member Competition and it is divided into three levels happening in the spring and summer of 2017. The Compression Test Competition (Level 1) focuses on the fabrication technologies needed to manufacture structural components from a combination of indigenous materials and recyclables, or indigenous materials alone. For Level 1, teams will develop 3D printable materials, build a 3D printing machine, and print two specimens: a truncated cone and a cylinder. The Level 2 Beam Member Competition is the second of three sub-competitions within the overall Structural Member Competition. For Level 2, teams will print a beam that will be tested.The Level 3 Head to Head Competition is the third of three sub-competitions within the overall Structural Member Competition. For Level 3, teams will develop 3D printable materials, use a 3D printing machine, and print three compression specimens of the elected material, three flexural specimens of the elected material, and one dome structure. Tests conducted on the specimens and the dome structure will determine Level 3 scores and awards. On Earth these same habitat manufacturing capabilities could be used to produce housing wherever affordable housing is needed and access to conventional building materials and skills is limited. Terrestrially, it is envisioned that local indigenous materials (dirt, clay, sand, etc.) could be combined with readily available recyclable materials and used to construct semi-permanent shelters against environmental elements for human habitation. The goal of the 3D-Printed Habitat Challenge is to foster the development of new technologies necessary to additively manufacture a habitat using local indigenous materials with, or without, recyclable materials. This paper will summarize the Level 2 results of this NASA Centennial Challenge competition and it will discuss related technology advancement.

Energy Return on Investment - Fuel Recycle

DOE Office of Scientific and Technical Information (OSTI.GOV)

Halsey, W; Simon, A J; Fratoni, M

2012-06-06

This report provides a methodology and requisite data to assess the potential Energy Return On Investment (EROI) for nuclear fuel cycle alternatives, and applies that methodology to a limited set of used fuel recycle scenarios. This paper is based on a study by Lawrence Livermore National Laboratory and a parallel evaluation by AREVA Federal Services LLC, both of which were sponsored by the DOE Fuel Cycle Technologies (FCT) Program. The focus of the LLNL effort was to develop a methodology that can be used by the FCT program for such analysis that is consistent with the broader energy modeling community,more » and the focus of the AREVA effort was to bring industrial experience and operational data into the analysis. This cooperative effort successfully combined expertise from the energy modeling community with expertise from the nuclear industry. Energy Return on Investment is one of many figures of merit on which investment in a new energy facility or process may be judged. EROI is the ratio of the energy delivered by a facility divided by the energy used to construct, operate and decommission that facility. While EROI is not the only criterion used to make an investment decision, it has been shown that, in technologically advanced societies, energy supplies must exceed a minimum EROI. Furthermore, technological history shows a trend towards higher EROI energy supplies. EROI calculations have been performed for many components of energy technology: oil wells, wind turbines, photovoltaic modules, biofuels, and nuclear reactors. This report represents the first standalone EROI analysis of nuclear fuel reprocessing (or recycling) facilities.« less

Value analysis of neodymium content in shredder feed: toward enabling the feasibility of rare earth magnet recycling.

PubMed

Bandara, H M Dhammika; Darcy, Julia W; Apelian, Diran; Emmert, Marion H

2014-06-17

In order to facilitate the development of recycling technologies for rare earth magnets from postconsumer products, we present herein an analysis of the neodymium (Nd) content in shredder scrap. This waste stream has been chosen on the basis of current business practices for the recycling of steel, aluminum, and copper from cars and household appliances, which contain significant amounts of rare earth magnets. Using approximations based on literature data, we have calculated the average Nd content in the ferrous shredder product stream to be between 0.13 and 0.29 kg per ton of ferrous scrap. A value analysis considering rare earth metal prices between 2002 and 2013 provides values between $1.32 and $145 per ton of ferrous scrap for this material, if recoverable as pure Nd metal. Furthermore, we present an analysis of the content and value of other rare earths (Pr, Dy, Tb).

Metamorphosis in the Porosity of Recycled Concretes Through the Use of a Recycled Polyethylene Terephthalate (PET) Additive. Correlations between the Porous Network and Concrete Properties

PubMed Central

Mendivil-Escalante, José Miguel; Gómez-Soberón, José Manuel; Almaral-Sánchez, Jorge Luis; Cabrera-Covarrubias, Francisca Guadalupe

2017-01-01

In the field of construction, sustainable building materials are currently undergoing a process of technological development. This study aims to contribute to understanding the behavior of the fundamental properties of concretes prepared with recycled coarse aggregates that incorporate a polyethylene terephthalate (PET)-based additive in their matrix (produced by synthesis and glycolysis of recycled PET bottles) in an attempt to reduce their high porosity. Techniques to measure the gas adsorption, water porosity, Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) were used to evaluate the effect of the additive on the physical, mechanical and microstructural properties of these concretes. Porosity reductions of up to 30.60% are achieved with the addition of 1%, 3%, 4%, 5%, 7% and 9% of the additive, defining a new state in the behavioral model of the additive (the overdosage point) in the concrete matrix; in addition, the porous network of these concretes and their correlation with other physical and mechanical properties are also explained. PMID:28772540

Metamorphosis in the Porosity of Recycled Concretes Through the Use of a Recycled Polyethylene Terephthalate (PET) Additive. Correlations between the Porous Network and Concrete Properties.

PubMed

Mendivil-Escalante, José Miguel; Gómez-Soberón, José Manuel; Almaral-Sánchez, Jorge Luis; Cabrera-Covarrubias, Francisca Guadalupe

2017-02-14

In the field of construction, sustainable building materials are currently undergoing a process of technological development. This study aims to contribute to understanding the behavior of the fundamental properties of concretes prepared with recycled coarse aggregates that incorporate a polyethylene terephthalate (PET)-based additive in their matrix (produced by synthesis and glycolysis of recycled PET bottles) in an attempt to reduce their high porosity. Techniques to measure the gas adsorption, water porosity, Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) were used to evaluate the effect of the additive on the physical, mechanical and microstructural properties of these concretes. Porosity reductions of up to 30.60% are achieved with the addition of 1%, 3%, 4%, 5%, 7% and 9% of the additive, defining a new state in the behavioral model of the additive (the overdosage point) in the concrete matrix; in addition, the porous network of these concretes and their correlation with other physical and mechanical properties are also explained.

Formation of PBDD/F from PBDE in electronic waste in recycling processes and under simulated extruding conditions.

PubMed

Zennegg, Markus; Schluep, Mathias; Streicher-Porte, Martin; Lienemann, Peter; Haag, Regula; Gerecke, Andreas C

2014-12-01

The increasing volumes of waste electrical and electronic equipment (WEEE) in Europe and developing economies demand for efficient disposal solutions. However, WEEE also contains toxic compounds and, therefore, there is a need for recycling technologies for WEEE that creates revenue without causing environmental harm. Among other fast developing economies, South Africa is tempting to make use of recycled plastic. Brominated flame retardants (BFRs) are additives used to protect plastic materials in electrical and electronic equipment (EEE) against ignition. Some BFRs are known persistent organic pollutants (POPs) and some BFRs can be transformed into highly toxic compounds such as polybrominated dibenzofurans and dioxins (PBDD/Fs). In this study, the contents of critical BFRs, i.e. polybrominated diphenyl ethers, and highly toxic PBDD/Fs were measured in WEEE material from Switzerland and South Africa. The formation of PBDD/Fs has been observed in two South African recycling processes and under controlled laboratory conditions. Total PBDE-contents in the South African and Swiss plastic waste varied between 1×10(3) and 7×10(6) μg kg(-1). A few WEEE plastic fractions exceeded the RoHS limit of 1×10(6) μg kg(-1) for PBDEs and thus they could not be used for recycling products without special treatment. The total content of ∑PBDFs was around 1×10(3) μg kg(-1). Such contents in materials do not pose a risk for consumer under normal conditions. Workers at recycling plants might be at risk. The measured formation rates of PBDFs were between 2×10(-5) and 2×10(-4)∑PBDE(-1) min(-1). Copyright © 2014 Elsevier Ltd. All rights reserved.

77 FR 12327 - Notice of Lodging of RCRA Consent Decree

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-29

.../k/a Casie Ecology Oil Salvage, Inc. and Mid-Atlantic Recycling Technologies, Inc.), Civil Action No..., and should refer to United States v. Pure Earth Recycling, Inc. (f/k/a Casie Ecology Oil Salvage, Inc...

Tech Transfer Office discusses the finer points of tire recycling

NASA Technical Reports Server (NTRS)

1995-01-01

NASA's Technology Transfer Office at Stennis worked with a tire recycling company in St. Francisville, La., to help the company make better use of the cryogenics, or supercold fluids, in its recycling process. The process separates the rubber from the steel belts and other particles. The rubber is broken down into a material called crumb. Other parts of the tire particle removed is called fluff.

Pricing Models for Dual-channel Reverse Supply Chain Considering Regional Differences under “Internet Recycling” Mode in China

NASA Astrophysics Data System (ADS)

Wu, Di; Li, Peng; Chen, Juhong

2018-01-01

In recent years, the Internet technology has been deeply influencing recycling industry to make it more intelligent and interconnected. However, most existing papers on “Internet Recycling” neglected the problem of pricing strategy under online and offline channels for different levels of recyclers. Moreover, the effect of regional differences has been emphasized a lot in dual-channel forward supply chain, but recycling field has seldom been concerned about it. In this paper, a recycling system consisting of one recycling center and several third-party recyclers (TPR) was investigated based on traditional mode and dual-channel mode. The dual-channel reverse supply chain model is transformed from traditional mode by the introduction of online channel. It involves two recycling modes, as recycling centre for online recovery and “Recycling center+TPR” for offline recovery. By establishing pricing strategies based on Stackelberg game model, the impacts of regional differences were analysed. Finally, numerical analysis was given to illustrate the effectiveness of the pricing mechanisms and strategies.

Possible Role of Green Chemistry in Addressing Environmenal Plastic Debris: Scientific, Economic and Policy Issues

NASA Astrophysics Data System (ADS)

Bayha, K. M.

2016-02-01

Plastics have revolutionized modern life, replacing other raw materials in a vast array of products, due to their ease in molding and shaping, as well as superior recalcitrance to wearing and aging. However, this functional benefit makes plastic one of the most problematic pollutants, since they accumulate as environmental debris for decades and possibly for centuries. Rightfully so, programs addressing plastic debris typically involve efforts to reduce consumption, reuse plastic products and recycle them when usefulness is complete. However, some of these options can be problematic for certain applications, as well as in countries that lack efficient municipal solid waste or recycling facilities. The principles of Green Chemistry were developed to help scientists design chemical products that reduce or eliminate the use or generation of hazardous substances. These principles have also been applied to developing sustainable or greener polymers for use in consumer plastics. For instance, the EPA's Green Chemistry Program awards the Presidential Green Chemistry Challenge Awards each year, with a large percentage of awards having gone to developments in greener polymers. Many of these advancements involve the development of sustainable bio-based, more degradable or more recyclable polymers that deliver significant environmental benefits. This presentation is meant to address what role the development of truly greener polymers might have in addressing environmental plastic debris in parallel with efforts to reduce, reuse and recycle. The intention is to evaluate the issues posed by traditional polymer types, address the ultimate goals of alternative polymer development and evaluate research on current alternative polymer technologies, in order to objectively assess their usefulness in addressing environmental plastic debris accumulation. In addition, the scientific, policy and market issues that may be impeding accurate development, evaluation and implementation of alternative polymers will be discussed.

Advanced in-duct sorbent injection for SO{sub 2} control. Topical report No. 2, Subtask 2.2: Design optimization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rosenhoover, W.A.; Stouffer, M.R.; Withum, J.A.

1994-12-01

The objective of this research project is to develop second-generation duct injection technology as a cost-effective SO{sub 2} control option for the 1990 Clean Air Act Amendments. Research is focused on the Advanced Coolside process, which has shown the potential for achieving the performance targets of 90% SO{sub 2} removal and 60% sorbent utilization. In Subtask 2.2, Design Optimization, process improvement was sought by optimizing sorbent recycle and by optimizing process equipment for reduced cost. The pilot plant recycle testing showed that 90% SO{sub 2} removal could be achieved at sorbent utilizations up to 75%. This testing also showed thatmore » the Advanced Coolside process has the potential to achieve very high removal efficiency (90 to greater than 99%). Two alternative contactor designs were developed, tested and optimized through pilot plant testing; the improved designs will reduce process costs significantly, while maintaining operability and performance essential to the process. Also, sorbent recycle handling equipment was optimized to reduce cost.« less

Additive Manufacturing of Syntactic Foams: Part 1: Development, Properties, and Recycling Potential of Filaments

NASA Astrophysics Data System (ADS)

Singh, Ashish Kumar; Patil, Balu; Hoffmann, Niklas; Saltonstall, Brooks; Doddamani, Mrityunjay; Gupta, Nikhil

2018-03-01

This work focuses on developing filaments of high-density polyethylene (HDPE) and their hollow particle-filled syntactic foams for commercial three-dimensional (3D) printers based on fused filament fabrication technology. Hollow fly-ash cenospheres were blended by 40 wt.% in a HDPE matrix to produce syntactic foam (HDPE40) filaments. Further, the recycling potential was studied by pelletizing the filaments again to extrude twice (2×) and three times (3×). The filaments were tensile tested at 10-4 s-1, 10-3 s-1, and 10-2 s-1 strain rates. HDPE40 filaments show an increasing trend in modulus and strength with the strain rate. Higher density and modulus were noticed for 2× filaments compared to 1× filaments because of the crushing of some cenospheres in the extrusion cycle. However, 2× and 3× filament densities are nearly the same, showing potential for recycling them. The filaments show better properties than the same materials processed by conventional injection molding. Micro-CT scans show a uniform dispersion of cenospheres in all filaments.

Space Life Support Technology Applications to Terrestrial Environmental Problems

NASA Technical Reports Server (NTRS)

Schwartzkopf, Steven H.; Sleeper, Howard L.

1993-01-01

Many of the problems now facing the human race on Earth are, in fact, life support issues. Decline of air Quality as a result of industrial and automotive emissions, pollution of ground water by organic pesticides or solvents, and the disposal of solid wastes are all examples of environmental problems that we must solve to sustain human life. The technologies currently under development to solve the problems of supporting human life for advanced space missions are extraordinarily synergistic with these environmental problems. The development of these technologies (including both physicochemical and bioregenerative types) is increasingly focused on closing the life support loop by removing and recycling contaminants and wastes to produce the materials necessary to sustain human life. By so doing, this technology development effort also focuses automatically on reducing resupply logistics requirements and increasing crew safety through increased self-sufficiency. This paper describes several technologies that have been developed to support human life in space and illustrates the applicability of the technologies to environmental problems including environmental remediation and pollution prevention.

Enhancement of the recycling of waste Ni-Cd and Ni-MH batteries by mechanical treatment.

PubMed

Huang, Kui; Li, Jia; Xu, Zhenming

2011-06-01

A serious environmental problem was presented by waste batteries resulting from lack of relevant regulations and effective recycling technologies in China. The present work considered the enhancement of waste Ni-Cd and Ni-MH batteries recycling by mechanical treatment. In the process of characterization, two types of waste batteries (Ni-Cd and Ni-MH batteries) were selected and their components were characterized in relation to their elemental chemical compositions. In the process of mechanical separation and recycling, waste Ni-Cd and Ni-MH batteries were processed by a recycling technology without a negative impact on the environment. The technology contained mechanical crushing, size classification, gravity separation, and magnetic separation. The results obtained demonstrated that: (1) Mechanical crushing was an effective process to strip the metallic parts from separators and pastes. High liberation efficiency of the metallic parts from separators and pastes was attained in the crushing process until the fractions reached particle sizes smaller than 2mm. (2) The classified materials mainly consisted of the fractions with the size of particles between 0.5 and 2mm after size classification. (3) The metallic concentrates of the samples were improved from around 75% to 90% by gravity separation. More than 90% of the metallic materials were separated into heavy fractions when the particle sizes were larger than 0.5mm. (4) The size of particles between 0.5 and 2mm and the rotational speed of the separator between 30 and 60 rpm were suitable for magnetic separation during industrial application, with the recycling efficiency exceeding 95%. Copyright © 2011 Elsevier Ltd. All rights reserved.

Cladding and duct materials for advanced nuclear recycle reactors

NASA Astrophysics Data System (ADS)

Allen, T. R.; Busby, J. T.; Klueh, R. L.; Maloy, S. A.; Toloczko, M. B.

2008-01-01

The expanded use of nuclear energy without risk of nuclear weapons proliferation and with safe nuclear waste disposal is a primary goal of the Global Nuclear Energy Partnership (GNEP). To achieve that goal the GNEP is exploring advanced technologies for recycling spent nuclear fuel that do not separate pure plutonium, and advanced reactors that consume transuranic elements from recycled spent fuel. The GNEP’s objectives will place high demands on reactor clad and structural materials. This article discusses the materials requirements of the GNEP’s advanced nuclear recycle reactors program.

Laboratory and Field Evaluation of In-Place Asphalt Recycling Technologies for Small Airfield Repair

DTIC Science & Technology

2013-06-01

Mariely Mejías-Santiago and William D. Carruth Geotechnical and Structures Laboratory US Army Engineer Research and Development Center 3909 Halls...24. Pavement structure at Test Site 1. ....................................................................................... 28  Figure 25. Pavement... structure at ERDC test site. ................................................................................ 30  Figure 26. Heatwurx HWX-30 electric

Semiannual patents review, January — June 2001.

Treesearch

Marguerite S. Sykes; Julie Blankenburg

2001-01-01

This review summarizes patents related to paper recycling that were issued during the first 6 months of 2001. Two online databases, Claims/U.S. Patents Abstracts and Derwent World Patents Index, were searched for this review. This semiannual feature is intended to inform readers about recent developments in equipment design, chemicals, and process technology for...

Semiannual patents review, July 2001-December 2001

Treesearch

Roland Gleisner; Marguerite Sykes; Julie Blankenburg

2002-01-01

This review summarizes patents related to paper recycling that were issued during the last six months of 2001. Two on-line databases, Claims/U.S. Patents Abstracts and Derwent World Patents Index, were searched for this review. This semiannual feature is intended to inform readers about recent developments in equipment design, chemicals and process technology for...

Effects of weathering on color loss of natural fiber thermoplastic composites

Treesearch

R.H. Falk; C. Felton; T. Lundin

2001-01-01

The technology currently exists to manufacture natural fiber thermoplastic composites from recycled materials. Development of commodity-building products from these composites would open up huge markets for waste-based materials in the US. To date, the construction industry has only accepted wood thermoplastic composite lumber (and only for limited applications). In...

Effects of weathering on color loss of natural fiber : thermoplastic composites

Treesearch

Robert H. Falk; Colin Felton; Thomas Lundin

2000-01-01

The technology currently exists to manufacture natural fiber-thermoplastic composites from recycled materials. Development of commodity building products from these composites would open huge markets for waste-based materials in the United States. To date, the construction industry has only accepted wood-thermoplastic composite lumber and only for limited applications...

Opportunities and Barriers to Resource Recovery and Recycling from Shredder Residue in the United States

NASA Astrophysics Data System (ADS)

Nayak, Naren; Apelian, Diran

2014-11-01

Shredder residue is the by-product remaining after ferrous and nonferrous metals have been recovered from the processing of vehicles, white goods, and peddler scrap. Shredder residue consists of glass, plastics, rubber, dirt, and small amounts of metal. It is estimated that 5-7 million tons of this shredder residue are landfilled each year in the United States. Technical advancements, coupled with European Union directives and the economic climate, have transformed the recycling of shredder residue in Europe. In the United States, however, regulatory controls and the cheap cost of landfill have worked against the advancement of recycling and recovery of this resource. The Argonne National Laboratory, which is funded by the U.S. Department of Energy, has investigated the effectiveness of recycling shredder residue into polymers. Other research has examined the use of shredder residue in waste-to-energy applications. To improve our ability to process and recycle shredder residue, an investigation of the regulatory, economic, and technological challenges was undertaken. The objective was to conduct a comprehensive review of work done to date, to document the composition of typical shredder output and to identify potential recoverable items (residual metals, plastics, rubber, foam, etc.). Along with uncovering potential new markets, the research would identify the technical, regulatory, and economic barriers to developing those markets.

Separating and Recycling Plastic, Glass, and Gallium from Waste Solar Cell Modules by Nitrogen Pyrolysis and Vacuum Decomposition.

PubMed

Zhang, Lingen; Xu, Zhenming

2016-09-06

Many countries have gained benefits through the solar cells industry due to its high efficiency and nonpolluting power generation associated with solar energy. Accordingly, the market of solar cell modules is expanding rapidly in recent decade. However, how to environmentally friendly and effectively recycle waste solar cell modules is seldom concerned. Based on nitrogen pyrolysis and vacuum decomposition, this work can successfully recycle useful organic components, glass, and gallium from solar cell modules. The results were summarized as follows: (i) nitrogen pyrolysis process can effectively decompose plastic. Organic conversion rate approached 100% in the condition of 773 K, 30 min, and 0.5 L/min N2 flow rate. But, it should be noted that pyrolysis temperature should not exceed 773 K, and harmful products would be increased with the increasing of temperature, such as benzene and its derivatives by GC-MS measurement; (ii) separation principle, products analysis, and optimization of vacuum decomposition were discussed. Gallium can be well recycled under temperature of 1123 K, system pressure of 1 Pa and reaction time of 40 min. This technology is quite significant in accordance with the "Reduce, Reuse, and Recycle Principle" for solid waste, and provides an opportunity for sustainable development of photovoltaic industry.

Requirements for, and benefits of, environmentally sound and economically viable management of battery recycling in the Philippines in the wake of Basel Convention trade restrictions

NASA Astrophysics Data System (ADS)

Hoffmann, U.; Wilson, B.

The ban on the export of used lead-acid batteries (ULAB) from Annex VII to non-Annex VII countries pursuant to decision III/1 of the Basel Convention reduced the availability of imported scrap feedstock for battery recycling in the Philippines. As ULAB supply from other developing countries becomes scarcer, the ban is likely to encourage and enhance collection and recuperation for domestically generated scrap. From a short-term perspective, this study explores the technological and managerial opportunities for improving the environmental and occupational health performance of the formal battery recycling sector and unregulated reconditioning. From a medium- and long-term point of view, the study investigates restructuring the informal ULAB's collection and recycling sector. The objective has been to make the smaller battery recyclers and reconditioners in the informal sector part of an effective and efficient collection infrastructure that supports an environmentally sound secondary lead sector. This approach gradually phases out uncontrolled, inefficient and environmentally unacceptable methods of secondary lead recovery. Due attention has also been paid to the logistical peculiarities of an archipelago, in particular the regional spread of collection infrastructure, collection and shipment costs as well as the assurance of environmentally safe transport.

System dynamics analysis of strategies to reduce energy use in aluminum-intensive sectors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hanes, Rebecca J.; Nicholson, Scott; 25-29 June 2017, Carpenter, Alberta

Aluminum is one of the most widely used materials in industry, with applications in buildings, vehicles, aircraft, and consumer products. Its ubiquity is also on the rise: aluminum is beginning to supplant steel in lightweight vehicles and aircraft, and is used in many green or LEED-certified buildings. Although aluminum tends to be highly recycled, particularly by manufacturers of aluminum products, the sector as a whole is still far from a closed system. As a result, the increase in aluminum consumption also means an increase in primary aluminum production-an energy-intensive process-and an increase in consumption of the raw material bauxite, whichmore » in the U.S. is almost entirely imported. Our objectives for this study are to identify and analyze aluminum sector technologies and practices that reduce the energy required to manufacture aluminum products and reduce U.S. dependence on imported aluminum and bauxite. To accomplish these objectives, we will develop a system dynamics (SD) model of aluminum production, use and recycling in key application areas, including aerospace, ground vehicles and consumer products. The model will cover the entire aluminum supply chain as it exists in the U.S., from bauxite importing and refining, to the manufacture of products, to the product use phase and end-of-life processing steps. Aluminum flows throughout the model will be determined by the annual domestic demand for each application area as well as demand projections that extend to 2030. Energy consumption will be tracked based on the flows of aluminum through each step of the supply chain. Using the SD model, we will evaluate several technologies and practices that have the potential to reduce energy consumption and reliance on imported bauxite. These include implementation of advanced primary aluminum production technologies, increased recycling within and between application areas, increased material efficiency and increased product lifetimes. Each of these strategies results in short term reductions in energy use, and every strategy except the advance production technologies will also reduce the need for imported bauxite. This model differs from other SD models previously built to study aluminum stocks and flows in two key areas- alloy recycling and product lifetimes. Aluminum recycling is frequently complicated by the need to maintain quality of many different alloys, especially in aerospace applications. This necessitates scrap sorting and product disassembly to avoid contamination; advanced recycling processes of this type are one of the strategies to be evaluated. Product lifetime similarly complicates aluminum recycling, as products with longer lifetimes yield smaller recycling streams compared to disposable or short lifetime products, such as soda cans. When these additional complexities are accounted for in the SD model, a more realistic idea of the short term and long term impacts of the various strategies can be captured, as can any potential synergies and trade-offs between the strategies. Results of the analysis will indicate which strategy, or combination of strategies, yields the lowest cumulative energy consumption and bauxite consumption required to satisfy current and future demand for aluminum products.« less

Biofloc technology application in aquaculture to support sustainable development goals.

PubMed

Bossier, Peter; Ekasari, Julie

2017-09-01

Biofloc technology (BFT) application offers benefits in improving aquaculture production that could contribute to the achievement of sustainable development goals. This technology could result in higher productivity with less impact to the environment. Furthermore, biofloc systems may be developed and performed in integration with other food production, thus promoting productive integrated systems, aiming at producing more food and feed from the same area of land with fewer input. The biofloc technology is still in its infant stage. A lot more research is needed to optimise the system (in relation to operational parameters) e.g. in relation to nutrient recycling, MAMP production, immunological effects. In addition research findings will need to be communicated to farmers as the implementation of biofloc technology will require upgrading their skills. © 2017 The Authors. Microbial Biotechnology published by John Wiley & Sons Ltd and Society for Applied Microbiology.

Global responses for recycling waste CRTs in e-waste.

PubMed

Singh, Narendra; Li, Jinhui; Zeng, Xianlai

2016-11-01

The management of used cathode ray tube (CRT) devices is a major problem worldwide due to rapid uptake of the technology and early obsolescence of CRT devices, which is considered an environment hazard if disposed improperly. Previously, their production has grown in step with computer and television demand but later on with rapid technological innovation; TVs and computer screens has been replaced by new products such as Liquid Crystal Displays (LCDs) and Plasma Display Panel (PDPs). This change creates a large volume of waste stream of obsolete CRTs waste in developed countries and developing countries will be becoming major CRTs waste producers in the upcoming years. We studied that there is also high level of trans-boundary movement of these devices as second-hand electronic equipment into developing countries in an attempt to bridge the 'digital divide'. Moreover, the current global production of e-waste is estimated to be '41million tonnes per year' where a major part of the e-waste stream consists of CRT devices. This review article provides a concise overview of world's current CRTs waste scenario, namely magnitude of the demand and processing, current disposal and recycling operations. Copyright © 2016 Elsevier Ltd. All rights reserved.

An innovative approach to predict technology evolution for the desoldering of printed circuit boards: A perspective from China and America.

PubMed

Wang, Chen; Zhao, Wu; Wang, Jie; Chen, Ling; Luo, Chun-Jing

2016-06-01

The printed circuit boards basis of electronic equipment have seen a rapid growth in recent years and played a significant role in modern life. Nowadays, the fact that electronic devices upgrade quickly necessitates a proper management of waste printed circuit boards. Non-destructive desoldering of waste printed circuit boards becomes the first and the most crucial step towards recycling electronic components. Owing to the diversity of materials and components, the separation process is difficult, which results in complex and expensive recovery of precious materials and electronic components from waste printed circuit boards. To cope with this problem, we proposed an innovative approach integrating Theory of Inventive Problem Solving (TRIZ) evolution theory and technology maturity mapping system to forecast the evolution trends of desoldering technology of waste printed circuit boards. This approach can be applied to analyse the technology evolution, as well as desoldering technology evolution, then research and development strategy and evolution laws can be recommended. As an example, the maturity of desoldering technology is analysed with a technology maturity mapping system model. What is more, desoldering methods in different stages are analysed and compared. According to the analysis, the technological evolution trends are predicted to be 'the law of energy conductivity' and 'increasing the degree of idealisation'. And the potential technology and evolutionary state of waste printed circuit boards are predicted, offering reference for future waste printed circuit boards recycling. © The Author(s) 2016.

77 FR 31611 - Proposed CERCLA Section 122(g)(4) Administrative Agreement and Order on Consent for the Mercury...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-29

... and Recycle Technologies, Inc., American Lamp Recycling, LLC, Lighting Resources, LLC, Western Finger Lakes Solid Waste Management Authority, H-B Instrument Company, Inc. and H.J. Heinz Company (hereinafter...

Expanding worldwide urban solid waste recycling: The Brazilian social technology in waste pickers inclusion.

PubMed

Rutkowski, Jacqueline E; Rutkowski, Emília W

2015-12-01

'If an integrated urban waste management system includes the informal recycling sector (IRS), there is a good chance that more solid waste is recycled' is common sense. However, informal integration brings additional social, environmental, and economic benefits, such as reduction of operational costs and environmental impacts of landfilling. Brazil is a global best practice example in terms of waste picker inclusion, and has received international recognition for its recycling levels. In addition to analysing the results of inclusive recycling approaches, this article evaluates a selection of the best Brazilian inclusive recycling practices and summaries and presents the resulting knowledge. The objective is to identify processes that enable the replication of the inclusion of the informal recycling sector model as part of municipal solid waste management. Qualitative and quantitative data have been collected in 25 Brazilian cities that have contracted waste pickers co-operatives for door-to-door selective collection of recyclables. Field data was collected in action research projects that worked with waste pickers co-operatives between 2006 and 2013. The Brazilian informal recycling sector integration model improves municipal solid waste recycling indicators: it shows an increase in the net tonness recycled, from 140 to 208 t month(-1), at a much lower cost per tonne than conventional selective collection systems. Inclusive systems show costs of US$35 per tonne of recyclables collected, well below the national average of US$195.26. This inclusive model improves the quality of collected material and the efficiency of municipal selective collection. It also diminishes the negative impacts of informal recycling, by reducing child labour, and by improving the conditions of work, occupational health and safety, and uncontrolled pollution. Although treating the Brazilian experience as a blueprint for transfer of experience in every case is unrealistic, the results suggest that this approach to informal sector integration can be considered among the global best practices for informal sector integration. The article closes with recommendations for deploying technology in other urban areas throughout the world. © The Author(s) 2015.

Energy efficiency of substance and energy recovery of selected waste fractions.

PubMed

Fricke, Klaus; Bahr, Tobias; Bidlingmaier, Werner; Springer, Christian

2011-04-01

In order to reduce the ecological impact of resource exploitation, the EU calls for sustainable options to increase the efficiency and productivity of the utilization of natural resources. This target can only be achieved by considering resource recovery from waste comprehensively. However, waste management measures have to be investigated critically and all aspects of substance-related recycling and energy recovery have to be carefully balanced. This article compares recovery methods for selected waste fractions with regard to their energy efficiency. Whether material recycling or energy recovery is the most energy efficient solution, is a question of particular relevance with regard to the following waste fractions: paper and cardboard, plastics and biowaste and also indirectly metals. For the described material categories material recycling has advantages compared to energy recovery. In accordance with the improved energy efficiency of substance opposed to energy recovery, substance-related recycling causes lower emissions of green house gases. For the fractions paper and cardboard, plastics, biowaste and metals it becomes apparent, that intensification of the separate collection systems in combination with a more intensive use of sorting technologies can increase the extent of material recycling. Collection and sorting systems must be coordinated. The objective of the overall system must be to achieve an optimum of the highest possible recovery rates in combination with a high quality of recyclables. The energy efficiency of substance related recycling of biowaste can be increased by intensifying the use of anaerobic technologies. In order to increase the energy efficiency of the overall system, the energy efficiencies of energy recovery plants must be increased so that the waste unsuitable for substance recycling is recycled or treated with the highest possible energy yield. Copyright © 2010 Elsevier Ltd. All rights reserved.

Nonproliferation Uncertainties, a Major Barrier to Used Nuclear Fuel Recycle in the United States

DOE Office of Scientific and Technical Information (OSTI.GOV)

Collins, Emory D; Ehinger, Michael H

2011-01-01

A study and comparison of the goals and understandings of nonproliferation authorities with those of used nuclear fuel (UNF) recycle advocates have uncovered (1) some of the basic reasons for the creation of uncertainties by each of the parties, (2) why these uncertainties have become a major barrier to a decision to recycle UNF components in the United States, and (3) what steps can be taken to clarify these uncertainties. Recent papers and viewpoints expressed by nonproliferation authorities and technical consultants were reviewed, summarized, and compared with results of recent fuel cycle systems analyses made at Oak Ridge National Laboratory.more » 1 Similarities and differences were identified, including both technical and policy factors. Nonproliferation authorities and a few UNF recycle advocates have recognized that the reprocessing technologies used for UNF component recycle do not offer significant nonproliferation differences; thus, the methods used can be chosen on some other basis, such as process efficiency, maturity, and/or economics. This paper reviews the safeguards implications beyond the simple assessment of UNF recycle technology selection. Differences in understanding that led to uncertainty barriers to UNF recycle include (1) the vulnerability of unseparated UNF, (2) the effects of time factors on production and accumulation of fissile plutonium isotopes and decay of the ?self-protecting radiation barrier,? (3) the chemistry of UNF components and relative ease of separation, and (4) the significant differences in commercialscale ?safeguards-by-design? UNF recycle facilities and smaller-scale covert operations. Application of safeguards-by-design and engineered safeguards can provide the defense-in-depth necessary for sufficient safeguards. Establishing these requirements for governing acceptable commercial UNF component recycle is essential.« less

Energy efficiency of substance and energy recovery of selected waste fractions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fricke, Klaus, E-mail: klaus.fricke@tu-bs.de; Bahr, Tobias, E-mail: t.bahr@tu-bs.de; Bidlingmaier, Werner, E-mail: werner.bidlingmaier@uni-weimar.de

In order to reduce the ecological impact of resource exploitation, the EU calls for sustainable options to increase the efficiency and productivity of the utilization of natural resources. This target can only be achieved by considering resource recovery from waste comprehensively. However, waste management measures have to be investigated critically and all aspects of substance-related recycling and energy recovery have to be carefully balanced. This article compares recovery methods for selected waste fractions with regard to their energy efficiency. Whether material recycling or energy recovery is the most energy efficient solution, is a question of particular relevance with regard tomore » the following waste fractions: paper and cardboard, plastics and biowaste and also indirectly metals. For the described material categories material recycling has advantages compared to energy recovery. In accordance with the improved energy efficiency of substance opposed to energy recovery, substance-related recycling causes lower emissions of green house gases. For the fractions paper and cardboard, plastics, biowaste and metals it becomes apparent, that intensification of the separate collection systems in combination with a more intensive use of sorting technologies can increase the extent of material recycling. Collection and sorting systems must be coordinated. The objective of the overall system must be to achieve an optimum of the highest possible recovery rates in combination with a high quality of recyclables. The energy efficiency of substance related recycling of biowaste can be increased by intensifying the use of anaerobic technologies. In order to increase the energy efficiency of the overall system, the energy efficiencies of energy recovery plants must be increased so that the waste unsuitable for substance recycling is recycled or treated with the highest possible energy yield.« less

Waste Treatment Technology Process Development Plan For Hanford Waste Treatment Plant Low Activity Waste Recycle

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCabe, Daniel J.; Wilmarth, William R.; Nash, Charles A.

2013-08-29

The purpose of this Process Development Plan is to summarize the objectives and plans for the technology development activities for an alternative path for disposition of the recycle stream that will be generated in the Hanford Waste Treatment Plant Low Activity Waste (LAW) vitrification facility (LAW Recycle). This plan covers the first phase of the development activities. The baseline plan for disposition of this stream is to recycle it to the WTP Pretreatment Facility, where it will be concentrated by evaporation and returned to the LAW vitrification facility. Because this stream contains components that are volatile at melter temperatures andmore » are also problematic for the glass waste form, they accumulate in the Recycle stream, exacerbating their impact on the number of LAW glass containers. Approximately 32% of the sodium in Supplemental LAW comes from glass formers used to make the extra glass to dilute the halides to acceptable concentrations in the LAW glass, and reducing the halides in the Recycle is a key component of this work. Additionally, under possible scenarios where the LAW vitrification facility commences operation prior to the WTP Pretreatment facility, this stream does not have a proven disposition path, and resolving this gap becomes vitally important. This task seeks to examine the impact of potential future disposition of this stream in the Hanford tank farms, and to develop a process that will remove radionuclides from this stream and allow its diversion to another disposition path, greatly decreasing the LAW vitrification mission duration and quantity of glass waste. The origin of this LAW Recycle stream will be from the Submerged Bed Scrubber (SBS) and the Wet Electrostatic Precipitator (WESP) from the LAW melter off-gas system. The stream is expected to be a dilute salt solution with near neutral pH, and will likely contain some insoluble solids from melter carryover or precipitates of scrubbed components (e.g. carbonates). The soluble components are mostly sodium and ammonium salts of nitrate, chloride, and fluoride. This stream has not been generated yet, and will not be available until the WTP begins operation, causing uncertainty in its composition, particularly the radionuclide content. This plan will provide an estimate of the likely composition and the basis for it, assess likely treatment technologies, identify potential disposition paths, establish target treatment limits, and recommend the testing needed to show feasibility. Two primary disposition options are proposed for investigation, one is concentration for storage in the tank farms, and the other is treatment prior to disposition in the Effluent Treatment Facility. One of the radionuclides that is volatile and expected to be in high concentration in this LAW Recycle stream is Technetium-99 ({sup 99}Tc), a long-lived radionuclide with a half-life of 210,000 years. Technetium will not be removed from the aqueous waste in the Hanford Waste Treatment and Immobilization Plant (WTP), and will primarily end up immobilized in the LAW glass, which will be disposed in the Integrated Disposal Facility (IDF). Because {sup 99}Tc has a very long half-life and is highly mobile, it is the largest dose contributor to the Performance Assessment (PA) of the IDF. Other radionuclides that are also expected to be in appreciable concentration in the LAW Recycle are {sup 129}I, {sup 90}Sr, {sup 137}Cs, and {sup 241}Am. The concentrations of these radionuclides in this stream will be much lower than in the LAW, but they will still be higher than limits for some of the other disposition pathways currently available. Although the baseline process will recycle this stream to the Pretreatment Facility, if the LAW facility begins operation first, this stream will not have a disposition path internal to WTP. One potential solution is to return the stream to the tank farms where it can be evaporated in the 242-A evaporator, or perhaps deploy an auxiliary evaporator to concentrate it prior to return to the tank farms. In either case, testing is needed to evaluate if this stream is compatible with the evaporator and the other wastes in the tank farm. It should be noted that prior experience in evaporation of another melter off-gas stream, the Recycle Stream at the SRS Defense Waste Processing Facility, unexpectedly caused deleterious impacts on evaporator scaling and formation of aluminosilicate solids before controls were implemented. The compatibility of this stream with other wastes and components in the tank farms has not been fully investigated, whether it is sent for storage in AW-102 in preparation for evaporation in 242-A evaporator, or if it is pre-concentrated in an auxiliary evaporator. This stream is expected to be unusual because it will be very high in corrosive species that are volatile in the melter (chloride, fluoride, sulfur), will have high ammonia, and will contain carryover particulates of glass-former chemicals. These species have potential to cause corrosion, precipitation, flammable gases, and scale in the tank farm system. Testing is needed to demonstrate acceptable conditions and limits for these compounds in wastes sent to the tank farms. Alternate disposition of this LAW Recycle stream could beneficially impact WTP, and may also remove a sizeable fraction of the 99Tc from the source term at the IDF. The alternative radionuclide removal process envisioned for this stream parallels the Actinide Removal Process that has been successfully used at SRS for several years. In that process, Monosodium Titanate (MST) is added to the tank waste to adsorb 90Sr and actinides, and then the MST and radionuclides are removed by filtration. The process proposed for investigation for the Hanford WTP LAW Recycle stream would similarly add MST to remove 90Sr and actinides, along with other absorbents or precipitating agents for the remaining radionuclides. These include inorganic reducing agents for Tc, and zeolites for 137Cs. After treatment, disposition of the decontaminated Recycle stream may be suitable for the Effluent Treatment Facility, where it could be evaporated and solidified. The contaminated slurry stream containing the absorbents and radionuclides will be preliminarily characterized in this phase of the program to evaluate disposal options, and disposition routes will be tested in the next phase. The testing described herein will aid in selection of the best disposal pathway. Several research tasks have been identified that are needed for this initial phase: imulant formulation- Concentration of Recycle to reduce storage volume; Blending of concentrated Recycle with tank waste; Sorption of radionuclides; Precipitation of radionuclides. After this initial phase of testing, additional tasks are expected to be identified for development. These tasks likely include evaluation and testing of applicable solid-liquid separation technologies, slurry rheology measurements, composition variability testing and evaluations, corrosion and erosion testing, slurry storage and immobilization investigations, and decontaminated Recycle evaporation and solidification. Although there are a number of unknown parameters listed in the technical details of the concepts described here, many of these parameters have precedence and do not generally require fundamental new scientific breakthroughs. Many of the materials and processes described are already used in radioactive applications in the DOE complex, or have been tested previously in comparable conditions. Some of these materials and equipment are already used in High Level Waste applications, which are much more complex and aggressive conditions than the LAW Recycle stream. In some cases, the unknown parameters are simply extensions of already studied conditions, such as tank waste corrosion chemistry. The list of testing needs at first appears daunting, but virtually all have been done before, although there are potential issues with compatibility with this unique waste stream. It is anticipated that the challenge will be more in integrating the system and complying with process limitations than in developing entirely new technologies. Several assumptions have been made in this document about the acceptability of radionuclide decontamination and potential waste forms for disposal. These assumptions have been used to define acceptability criteria for feasibility studies on removal. These limits are not intended to define regulatory or facility limits, but rather provide a starting point for evaluating various technologies.« less

Has the question of e-waste opened a Pandora's box? An overview of unpredictable issues and challenges.

PubMed

Bakhiyi, Bouchra; Gravel, Sabrina; Ceballos, Diana; Flynn, Michael A; Zayed, Joseph

2018-01-01

Despite regulatory efforts and position papers, electrical and electronic waste (e-waste) remains ill-managed as evidenced by the extremely low rates of proper e-waste recycling (e-recycling) worldwide, ongoing illegal shipments to developing countries and constantly reported human health issues and environmental pollution. The objectives of this review are, first, to expose the complexity of e-waste problems, and then to suggest possible upstream and downstream solutions. Exploring e-waste issues is akin to opening a Pandora's box. Thus, a review of prevailing e-waste management practices reveals complex and often intertwined gaps, issues and challenges. These include the absence of any consistent definition of e-waste to date, a prevalent toxic potential still involving already banned or restricted hazardous components such as heavy metals and persistent and bioaccumulative organic compounds, a relentless growth in e-waste volume fueled by planned obsolescence and unsustainable consumption, problematic e-recycling processes, a fragile formal e-recycling sector, sustained and more harmful informal e-recycling practices, and more convoluted and unpredictable patterns of illegal e-waste trade. A close examination of the e-waste legacy contamination reveals critical human health concerns, including significant occupational exposure during both formal and informal e-recycling, and persistent environmental contamination, particularly in some developing countries. However, newly detected e-waste contaminants as well as unexpected sources and environmental fates of contaminants are among the emerging issues that raise concerns. Moreover, scientific knowledge gaps remain regarding the complexity and magnitude of the e-waste legacy contamination, specifically, a comprehensive characterization of e-waste contaminants, information on the scale of legacy contamination in developing countries and on the potential environmental damage in developed countries, and a stronger body of evidence of adverse health effects specifically ascribed to e-waste contaminants. However, the knowledge accumulated to date is sufficient to raise awareness and concern among all stakeholders. Potential solutions to curb e-waste issues should be addressed comprehensively, by focusing on two fronts: upstream and downstream. Potential upstream solutions should focus on more rational and eco-oriented consumer habits in order to decrease e-waste quantities while fostering ethical and sustained commitments from manufacturers, which include a limited usage of hazardous compounds and an optimal increase in e-waste recyclability. At the downstream level, solutions should include suitable and pragmatic actions to progressively reduce the illegal e-waste trade particularly through international cooperation and coordination, better enforcement of domestic laws, and monitoring in both exporting and receiving countries, along with the supervised integration of the informal sector into the recycling system of developing countries and global expansion of formal e-waste collection and recycling activities. Downstream solutions should also introduce stronger reverse logistics, together with upgraded, more affordable, and eco-friendly and worker-friendly e-recycling technologies to ensure that benefits are derived fully and safely from the great economic potential of e-waste. Copyright © 2017 Elsevier Ltd. All rights reserved.

Technologies for utilizing natural resources create new job opportunities in the geosciences in developing countries

NASA Astrophysics Data System (ADS)

Aswathanarayana, U.

Water, soils, minerals, and biota constitute a community's most significant natural resources. Innovations in technology are generating new jobs in converting into a resource what was yesterday a non-resource; in developing process and control technologies to minimize wastes; and in waste recycling.“Resources are not, they become,” in the words of Zimmerman. In the case of the developing countries, the technologies of choice have not only to be ecologically sustainable and economically viable, but more importantly, employment generating. The new kinds of jobs—for example, in poverty alleviation projects via micro-enterprises based on value-added processing of natural resources—have a strong environmental relevance and tend to lie at the interface of several traditional scientific disciplines. Geoscience graduates in the developing countries are best placed to take advantage of these new job opportunities involving Earth materials, but only if they are exposed to broad-based geoscience instruction.

Plastic Recycling Experiments in Materials Education

NASA Technical Reports Server (NTRS)

Liu, Ping; Waskom, Tommy L.

1996-01-01

The objective of this project was to introduce a series of plastic recycling experiments to students in materials-related courses such as materials science, material technology and materials testing. With the plastic recycling experiments, students not only can learn the fundamentals of plastic processing and properties as in conventional materials courses, but also can be exposed to the issue of materials life cycle and the impact on society and environment.

HANDBOOK: RECYCLING AND REUSE OF MATERIAL FOUND ON SUPERFUND SITES

EPA Science Inventory

This document provides assistance in identifying potential recycling technologies for a wide variety of contaminants and matrices. Personnel at Superfund and Resource Conservation and Recovery Act (RCRA) Corrective Action sites face the challenge of selecting remedial options for...

Recycled Materials in European Highway Environments : Uses, Technologies, and Policies

DOT National Transportation Integrated Search

2000-10-01

The objective of this scanning tour was to review and document innovative policies, programs, and techniques that promote the use of recycled materials in the highway environment. The U.S. delegation met with more than 100 representatives from transp...

REFUSE OF FERMENTATION BRINES IN THE CUCUMBER PICKLING INDUSTRY

EPA Science Inventory

The project evaluated on a commercial scale the technological and economic feasibility of recycling spent cucumber fermentation brine. Two brine treatment procedures, heat treatment and chemical treatment, were used. The results showed that brine recycling was practical on a comm...

Planning of Eka Hospital Pekanbaru wastewater recycling facility

NASA Astrophysics Data System (ADS)

Jecky, A.; Andrio, D.; Sasmita, A.

2018-04-01

The Ministry of Public Works No. 06 2011 required the large scale of water to conserve the water resource, Eka Hospital Pekanbaru have to improve the sewage treatment plant through the wastewater recycling. The effluent from the plant can be used to landscape gardening and non-potable activities. The wastewater recycling design was done by analyzing the existing condition of thesewage treatment plant, determine the effluent quality standards for wastewater recycling, selected of alternative technology and processing, design the treatment unit and analyze the economic aspects. The design of recycling facility by using of combination cartridge filters processing, ultrafiltration membranes, and desinfection by chlorination. The wastewater recycling capacity approximately of 75 m3/day or 75% of the STP effluent. The estimated costs for installation of wastewater recycling and operation and maintenance per month are Rp 111,708,000 and Rp 2,498,000 respectively.

Optics & Materials Science & Technology (OMST) Organization at LLNL

ScienceCinema

Suratwala,; Tayyab,; Nguyen, Hoang; Bude, Jeff; Dylla-Spears, Rebecca

2018-06-13

The Optics and Materials Science & Technology (OMST) organization at Lawrence Livermore National Laboratory (LLNL) supplies optics, recycles optics, and performs the materials science and technology to advance optics and optical materials for high-power and high-energy lasers for a variety of missions. The organization is a core capability at LLNL. We have a strong partnership with many optical fabricators, universities and national laboratories to accomplish our goals. The organization has a long history of performing fundamental optical materials science, developing them into useful technologies, and transferring them into production both on-site and off-site. We are successfully continuing this same strategy today.

Optics & Materials Science & Technology (OMST) Organization at LLNL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Suratwala,; Tayyab,; Nguyen, Hoang

The Optics and Materials Science & Technology (OMST) organization at Lawrence Livermore National Laboratory (LLNL) supplies optics, recycles optics, and performs the materials science and technology to advance optics and optical materials for high-power and high-energy lasers for a variety of missions. The organization is a core capability at LLNL. We have a strong partnership with many optical fabricators, universities and national laboratories to accomplish our goals. The organization has a long history of performing fundamental optical materials science, developing them into useful technologies, and transferring them into production both on-site and off-site. We are successfully continuing this same strategymore » today.« less

Production of Methane and Water from Crew Plastic Waste

NASA Technical Reports Server (NTRS)

Captain, Janine; Santiago, Eddie; Parrish, Clyde; Strayer, Richard F.; Garland, Jay L.

2008-01-01

Recycling is a technology that will be key to creating a self sustaining lunar outpost. The plastics used for food packaging provide a source of material that could be recycled to produce water and methane. The recycling of these plastics will require some additional resources that will affect the initial estimate of starting materials that will have to be transported from earth, mainly oxygen, energy and mass. These requirements will vary depending on the recycling conditions. The degredation products of these plastics will vary under different atmospheric conditions. An estimate of the the production rate of methane and water using typical ISRU processes along with the plastic recycling will be presented.

Product self-management: evolution in recycling and reuse.

PubMed

Thomas, Valerie M

2003-12-01

This paper explores the potential to make product recycling and reuse easier by shifting responsibility for product management toward the product itself. Examples range from barcode-enabled Internet sales of used products to RFID-enabled garbage trucks that identify recyclable items and provide rebates. Initial steps toward product self-management have made opportunistic use of product bar codes and Internet markets. In the United States, Internet markets are driving increased reuse of products. In the European Union, recycling and waste management policy is driving the use of radio electronics in waste management. Prospects for product self-management are assessed from both a technological and an economic perspective. The technological analysis indicates that radio-frequency tags offer some advantages over bar codes, but their application to product self-management requires considerable investment in the waste management infrastructure. This suggests that early applications of advanced product tags are most suitable for Germany and other countries where the waste management industry has already integrated information technology into its operations. The economic analysis indicates that increased reuse of products can reduce consumption of new products and materials, although on a less than one-to-one basis, simultaneously reducing costs for consumers and deriving more value from existing products.

Eco-Balance analysis of the disused lead-acid-batteries recycling technology

NASA Astrophysics Data System (ADS)

Kamińska, Ewa; Kamiński, Tomasz

2017-10-01

The article presents the results of the eco-balance analysis of the disused lead-acid batteries recycling process. Test-dedicated technology offers the possibility to recover other elements, for example, polypropylene of the battery case or to obtain crystalline sodium sulphate. The life cycle assessment was made using ReCiPe and IMPACT2002 + methods. The results are shown as environmental points [Pt]. The results are shown in the environmental categories, specific for each of the methods grouped in the impact categories. 1 Mg of the processed srap was a dopted as the functional unit. The results of the analyses indicate that recycling processes may provide the environmental impact of recycling technology less harmful. Repeated use of lead causes that its original sources are not explored. Similarly, the use of granule production-dedicated polypropylene extracted from battery casings that are used in the plastics industry, has environmental benefits. Due to the widespread use of lead-acid batteries, the attention should be paid to their proper utilization, especially in terms of heavy metals, especially lead. According to the calculations, the highest level of environmental benefits from the use of lead from secondary sources in the production of new products, was observed in the refining process.

Evidence-based integrated environmental solutions for secondary lead smelters: pollution prevention and waste minimization technologies and practices.

PubMed

Genaidy, A M; Sequeira, R; Tolaymat, T; Kohler, J; Rinder, M

2009-05-01

An evidence-based methodology was adopted in this research to establish strategies to increase lead recovery and recycling via a systematic review and critical appraisal of the published literature. In particular, the research examines pollution prevention and waste minimization practices and technologies that meet the following criteria: (a) reduce/recover/recycle the largest quantities of lead currently being disposed of as waste, (b) technically and economically viable, that is, ready to be diffused and easily transferable, and (c) strong industry interest (i.e., industry would consider implementing projects with higher payback periods). The following specific aims are designed to achieve the study objectives: Aim 1 - To describe the recycling process of recovering refined lead from scrap; Aim 2 - To document pollution prevention and waste management technologies and practices adopted by US stakeholders along the trajectory of LAB and lead product life cycle; Aim 3 - To explore improved practices and technologies which are employed by other organizations with an emphasis on the aforementioned criteria; Aim 4 - To demonstrate the economic and environmental costs and benefits of applying improved technologies and practices to existing US smelting operations; and Aim 5 - To evaluate improved environmental technologies and practices using an algorithm that integrates quantitative and qualitative criteria. The process of identifying relevant articles and reports was documented. The description of evidence was presented for current practices and technologies used by US smelters as well as improved practices and technologies. Options for integrated environmental solutions for secondary smelters were introduced and rank ordered on the basis of costs (i.e., capital investment) and benefits (i.e., production increases, energy and flux savings, and reduction of SO(2) and slag). An example was provided to demonstrate the utility of the algorithm by detailing the costs and benefits associated with different combinations of practices and technologies. The evidence-based methodology documented in this research reveals that it is technically and economically feasible to implement integrated environmental solutions to increase lead recovery and recycling among US smelters. The working example presented in this research can be confirmed with US stakeholders and form the basis for implementable solutions in the lead smelter and product industries to help reverse the overall trend of declining life-cycle recycling rates.

Problems of Waste Management at Poultry Plants and Ways to Address Them

NASA Astrophysics Data System (ADS)

Lazareva, L. P.; Kostryakova, O. N.

2017-11-01

The paper analyzes scientific literature on manure recycling and systems of waste management at two poultry plants that use different technologies of poultry housing and manure disposal and calculates the volumes of waste generation for two plants. The authors suggest an economically and ecologically efficient manure utilization technology, consider the feasibility of replacing traditional fuel with the one produced by manure recycling and calculate expected profits and the payback time of equipment.

Validation of the mix design process for cold in-place rehabilitation using foamed asphalt.

DOT National Transportation Integrated Search

2007-06-01

Asphalt pavement recycling has grown dramatically over the last few years as a viable : technology to rehabilitate existing asphalt pavements. Iowa's current Cold In-place : Recycling (CIR) practice utilizes a generic recipe specification to define t...

Data availability and the need for research to localize, quantify and recycle critical metals in information technology, telecommunication and consumer equipment.

PubMed

Chancerel, Perrine; Rotter, Vera Susanne; Ueberschaar, Maximilian; Marwede, Max; Nissen, Nils F; Lang, Klaus-Dieter

2013-10-01

The supply of critical metals like gallium, germanium, indium and rare earths elements (REE) is of technological, economic and strategic relevance in the manufacturing of electrical and electronic equipment (EEE). Recycling is one of the key strategies to secure the long-term supply of these metals. The dissipation of the metals related to the low concentrations in the products and to the configuration of the life cycle (short use time, insufficient collection, treatment focusing on the recovery of other materials) creates challenges to achieve efficient recycling. This article assesses the available data and sets priorities for further research aimed at developing solutions to improve the recycling of seven critical metals or metal families (antimony, cobalt, gallium, germanium, indium, REE and tantalum). Twenty-six metal applications were identified for those six metals and the REE family. The criteria used for the assessment are (i) the metal criticality related to strategic and economic issues; (ii) the share of the worldwide mine or refinery production going to EEE manufacturing; (iii) rough estimates of the concentration and the content of the metals in the products; (iv) the accuracy of the data already available; and (v) the occurrence of the application in specific WEEE groups. Eight applications were classified as relevant for further research, including the use of antimony as a flame retardant, gallium and germanium in integrated circuits, rare earths in phosphors and permanent magnets, cobalt in batteries, tantalum capacitors and indium as an indium-tin-oxide transparent conductive layer in flat displays.

Model-Based Diagnosis and Prognosis of a Water Recycling System

NASA Technical Reports Server (NTRS)

Roychoudhury, Indranil; Hafiychuk, Vasyl; Goebel, Kai Frank

2013-01-01

A water recycling system (WRS) deployed at NASA Ames Research Center s Sustainability Base (an energy efficient office building that integrates some novel technologies developed for space applications) will serve as a testbed for long duration testing of next generation spacecraft water recycling systems for future human spaceflight missions. This system cleans graywater (waste water collected from sinks and showers) and recycles it into clean water. Like all engineered systems, the WRS is prone to standard degradation due to regular use, as well as other faults. Diagnostic and prognostic applications will be deployed on the WRS to ensure its safe, efficient, and correct operation. The diagnostic and prognostic results can be used to enable condition-based maintenance to avoid unplanned outages, and perhaps extend the useful life of the WRS. Diagnosis involves detecting when a fault occurs, isolating the root cause of the fault, and identifying the extent of damage. Prognosis involves predicting when the system will reach its end of life irrespective of whether an abnormal condition is present or not. In this paper, first, we develop a physics model of both nominal and faulty system behavior of the WRS. Then, we apply an integrated model-based diagnosis and prognosis framework to the simulation model of the WRS for several different fault scenarios to detect, isolate, and identify faults, and predict the end of life in each fault scenario, and present the experimental results.

Small Scale Gasification Application and Perspectives in Circular Economy

NASA Astrophysics Data System (ADS)

Klavins, Maris; Bisters, Valdis; Burlakovs, Juris

2018-06-01

Gasification is the process converting solid fuels as coal and organic plant matter, or biomass into combustible gas, called syngas. Gasification is a thermal conversion process using carbonaceous fuel, and it differs substantially from other thermal processes such as incineration or pyrolysis. The process can be used with virtually any carbonaceous fuel. It is an endothermic thermal conversion process, with partial oxidation being the dominant feature. Gasification converts various feedstock including waste to a syngas. Instead of producing only heat and electricity, synthesis gas produced by gasification may be transformed into commercial products with higher value as transport fuels, fertilizers, chemicals and even to substitute natural gas. Thermo-chemical conversion of biomass and solid municipal waste is developing as a tool to promote the idea of energy system without fossil fuels to a reality. In municipal solid waste management, gasification does not compete with recycling, moreover it enhances recycling programs. Pre-processing and after-processing must increase the amount of recyclables in the circular economy. Additionally, end of life plastics can serve as an energy feedstock for gasification as otherwise it cannot be sorted out and recycled. There is great potential for application of gasification technology within the biomass waste and solid waste management sector. Industrial self-consumption in the mode of combined heat and power can contribute to sustainable economic development within a circular economy.

Global reverse supply chain design for solid waste recycling under uncertainties and carbon emission constraint.

PubMed

Xu, Zhitao; Elomri, Adel; Pokharel, Shaligram; Zhang, Qin; Ming, X G; Liu, Wenjie

2017-06-01

The emergence of concerns over environmental protection, resource conservation as well as the development of logistics operations and manufacturing technology has led several countries to implement formal collection and recycling systems of solid waste. Such recycling system has the benefits of reducing environmental pollution, boosting the economy by creating new jobs, and generating income from trading the recyclable materials. This leads to the formation of a global reverse supply chain (GRSC) of solid waste. In this paper, we investigate the design of such a GRSC with a special emphasis on three aspects; (1) uncertainty of waste collection levels, (2) associated carbon emissions, and (3) challenges posed by the supply chain's global aspect, particularly the maritime transportation costs and currency exchange rates. To the best of our knowledge, this paper is the first attempt to integrate the three above-mentioned important aspects in the design of a GRSC. We have used mixed integer-linear programming method along with robust optimization to develop the model which is validated using a sample case study of e-waste management. Our results show that using a robust model by taking the complex interactions characterizing global reverse supply chain networks into account, we can create a better GRSC. The effect of uncertainties and carbon constraints on decisions to reduce costs and emissions are also shown. Copyright © 2017 Elsevier Ltd. All rights reserved.

Hydrothermal Processing of Base Camp Solid Wastes To Allow Onsite Recycling

DTIC Science & Technology

2008-09-01

ER D C/ CE R L TR -0 8 -1 3 Hydrothermal Processing of Base Camp Solid Wastes To Allow Onsite Recycling Gary L. Gerdes, Deborah...release; distribution is unlimited. ERDC/CERL TR-08-13 September 2008 Hydrothermal Processing of Base Camp Solid Wastes To Allow Onsite Recycling...a technology to process domestic solid waste using a unique hydrothermal system. The process was successfully demonstrated at Forts Benning and

The life cycle assessment of cellulose pulp from waste cotton via the SaXcell™ process.

NASA Astrophysics Data System (ADS)

Oelerich, Jens; Bijleveld, Marijn; Bouwhuis, Gerrit H.; Brinks, Ger J.

2017-10-01

Recycling of cotton waste into high value products is a longstanding goal in textile research. The SaXcellTM process provides a chemical recycling route towards virgin fibres. In this study a Life cycle assessment (LCA) is conducted to measure the impact of the chemical recycling of cotton waste on the environment. Pure cotton waste and cotton containing 10 % of polyester are elaborated. The results show that chemical recycling via the SaXcellTM process can have a lower impact on climate change and other impact category than comparable pulping technologies.

Environmental burdens in the management of end-of-life cathode ray tubes.

PubMed

Rocchetti, Laura; Beolchini, Francesca

2014-02-01

We compared the environmental burdens in the management of end-of life cathode ray tubes (CRTs) within two frameworks according to the different technologies of the production of televisions/monitors. In the first case, CRT recycling is addressed to the recovery of the panel and funnel glass for the manufacturing of new CRT screens. In the second case, where flat screen technology has replaced that of CRT, the recycling is addressed to the recovery of the glass cullet and lead for other applications. The impacts were evaluated according to the problem-oriented methodology of the Institute of Environmental Sciences, Leiden University, Leiden, The Netherlands. Our data confirm that in both cases, the recycling treatment allows benefits to be gained for the environment through the recovery of the secondary raw materials. These benefits are higher for the "CRT technology" framework (1 kg CO2 saved per CRT) than for the "flat screen technology" (0.9 kg CO2 saved, per CRT, as the highest possible), mainly due to the high energy consumption for lead separation from the funnel glass. Furthermore, the recovery of yttrium from the fluorescent powders that are a residue of the recycling treatment would further improve the CO2 credit for both the frameworks considered, which would provide a further saving of about 0.75 kg CO2 per CRT, net of the energy and raw materials needed for the recovery. Overall, this study confirms that, even with a change in the destination of the recovered materials, the recycling processes provide a benefit for the environment: indeed the higher loads for the environment are balanced by avoiding the primary production of the recovered materials. Copyright © 2013 Elsevier Ltd. All rights reserved.

Semiannual patents review July 2002–December 2002

Treesearch

Roland Gleisner; Julie Blankenburg

2003-01-01

This review summarizes patents related to paper recycling that were issued during the last six months of 2002. Two on-line databases, Claims/U.S. Patents Abstracts and Derwent World Patents Index, were searched for this review. This semiannual feature is intended to inform readers about recent developments in equipment design, chemicals, and process technology for...

Semiannual patents review, January-June 1999

Treesearch

Marguerite Sykes; Julie Blankenburg

1999-01-01

This review summarizes patents related to paper recycling that were issued during the first 6 months of 1999. The two on-line databases used for this search were C1aims/U.S. Patents Abstracts and Derwent World Patents Index. This semiannual feature is intended to inform readers about the latest developments in equipment design, chemicals, and process technology for...

ETV REPORT: AND STATEMENT: HYDROMATIX 786E ION EXCHANGE RINSEWATER RECYCLING SYSTEM

EPA Science Inventory

RPA's ETV Program, through the NRMRL, has partnered with the California Dept. of Toxic Substances Contol (DTSCO) under an ETV Pilot to verify pollution prevention, recycling, and waste treatment technologies. This report provides a verification of performance results for the Hydr...

Water recycling at the Millennium Dome.

PubMed

Hills, S; Smith, A; Hardy, P; Birks, R

2001-01-01

Thames Water is working with the New Millennium Experience Company to provide a water recycling system for the Millennium Dome which will supply 500 m3/d of reclaimed water for WC and urinal flushing. The system will treat water from three sources: rainwater--from the Dome roof greywater--from handbasins in the toilet blocks groundwater--from beneath the Dome site The treatment technologies will range from "natural" reedbeds for the rainwater, to more sophisticated options, including biological aerated filters and membranes for the greywater and groundwater. Pilot scale trials were used to design the optimum configuration. In addition to the recycling system, water efficient devices will be installed in three of the core toilet blocks as part of a programme of research into the effectiveness of conservation measures. Data on water usage and customer behaviour will be collected via a comprehensive metering system. Information from the Dome project on the economics and efficiency of on-site recycling at large scale and data on water efficient devices, customer perception and behaviour will be of great value to the water industry. For Thames Water, the project provides vital input to the development of future water resource strategies.

Cellulase recycling in biorefineries--is it possible?

PubMed

Gomes, Daniel; Rodrigues, Ana Cristina; Domingues, Lucília; Gama, Miguel

2015-05-01

On a near future, bio-based economy will assume a key role in our lives. Lignocellulosic materials (e.g., agroforestry residues, industrial/solid wastes) represent a cheaper and environmentally friendly option to fossil fuels. Indeed, following suitable processing, they can be metabolized by different microorganisms to produce a wide range of compounds currently obtained by chemical synthesis. However, due to the recalcitrant nature of these materials, they cannot be directly used by microorganisms, the conversion of polysaccharides into simpler sugars being thus required. This conversion, which is usually undertaken enzymatically, represents a significant part on the final cost of the process. This fact has driven intense efforts on the reduction of the enzyme cost following different strategies. Here, we describe the fundamentals of the enzyme recycling technology, more specifically, cellulase recycling. We focus on the main strategies available for the recovery of both the liquid- and solid-bound enzyme fractions and discuss the relevant operational parameters (e.g., composition, temperature, additives, and pH). Although the efforts from the industry and enzyme suppliers are primarily oriented toward the development of enzyme cocktails able to quickly and effectively process biomass, it seems clear by now that enzyme recycling is technically possible.

Syngas Production By Thermochemical Conversion Of H2o And Co2 Mixtures Using A Novel Reactor Design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pearlman, Howard; Chen, Chien-Hua

The Department of Energy awarded Advanced Cooling Technologies, Inc. (ACT) an SBIR Phase II contract (#DE-SC0004729) to develop a high-temperature solar thermochemical reactor for syngas production using water and/or carbon dioxide as feedstocks. The technology aims to provide a renewable and sustainable alternative to fossil fuels, promote energy independence and mitigate adverse issues associated with climate change by essentially recycling carbon from carbon dioxide emitted by the combustion of hydrocarbon fuels. To commercialize the technology and drive down the cost of solar fuels, new advances are needed in materials development and reactor design, both of which are integral elements inmore » this program.« less

Simultaneous material flow analysis of nickel, chromium, and molybdenum used in alloy steel by means of input-output analysis.

PubMed

Nakajima, Kenichi; Ohno, Hajime; Kondo, Yasushi; Matsubae, Kazuyo; Takeda, Osamu; Miki, Takahiro; Nakamura, Shinichiro; Nagasaka, Tetsuya

2013-05-07

Steel is not elemental iron but rather a group of iron-based alloys containing many elements, especially chromium, nickel, and molybdenum. Steel recycling is expected to promote efficient resource use. However, open-loop recycling of steel could result in quality loss of nickel and molybdenum and/or material loss of chromium. Knowledge about alloying element substance flow is needed to avoid such losses. Material flow analyses (MFAs) indicate the importance of steel recycling to recovery of alloying elements. Flows of nickel, chromium, and molybdenum are interconnected, but MFAs have paid little attention to the interconnected flow of materials/substances in supply chains. This study combined a waste input-output material flow model and physical unit input-output analysis to perform a simultaneous MFA for nickel, chromium, and molybdenum in the Japanese economy in 2000. Results indicated the importance of recovery of these elements in recycling policies for end-of-life (EoL) vehicles and constructions. Improvement in EoL sorting technologies and implementation of designs for recycling/disassembly at the manufacturing phase are needed. Possible solutions include development of sorting processes for steel scrap and introduction of easier methods for identifying the composition of secondary resources. Recovery of steel scrap with a high alloy content will reduce primary inputs of alloying elements and contribute to more efficient resource use.

Plastics disassembly versus bulk recycling: engineering design for end-of-life electronics resource recovery.

PubMed

Rios, Pedro; Stuart, Julie Ann; Grant, Ed

2003-12-01

Annual plastic flows through the business and consumer electronics manufacturing supply chain include nearly 3 billion lb of high-value engineering plastics derived from petroleum. The recovery of resource value from this stream presents critical challenges in areas of materials identification and recycling process design that demand new green engineering technologies applied together with life cycle assessment and ecological supply chain analysis to create viable plastics-to-plastics supply cycles. The sustainable recovery of potentially high-value engineering plastics streams requires that recyclers either avoid mixing plastic parts or purify later by separating smaller plastic pieces created in volume reduction (shredding) steps. Identification and separation constitute significant barriers in the plastics-to-plastics recycling value proposition. In the present work, we develop a model that accepts randomly arriving electronic products to study scenarios by which a recycler might identify and separate high-value engineering plastics as well as metals. Using discrete eventsimulation,we compare current mixed plastics recovery with spectrochemical plastic resin identification and subsequent sorting. Our results show that limited disassembly with whole-part identification can produce substantial yields in separated streams of recovered engineering thermoplastics. We find that disassembly with identification does not constitute a bottleneck, but rather, with relatively few workers, can be configured to pull the process and thus decrease maximum staging space requirements.

Restaurant oil and grease management in Hong Kong.

PubMed

Yau, Yiu-Hung; Rudolph, Victor; Lo, Cat Chui-Man; Wu, Kam-Chau

2018-06-24

Oil and grease (O&G) in wastewater can be considered as two parts or proportion contained in emulsion which exceeded O&G standard. Most of oil becomes emulsified with water when they pass through grease trap and discharged in the effluents. Thus, it may indicate that either treatment of grease traps or standards for O&G content stipulated in technical memorandum of Water Pollution Control Ordinance (WPCO) do not reflect the actual situation. Existing grease traps should be upgraded to meet the requirements of WPCO. Alternative technologies need to be developed to tackle this unsolved problem. Good management and practices are also important to ensure proper collection and waste recycling rather than just disposing effluent into drains. Collected O&G content can be recycled as valuable products such as biofuel, flotation agent, or other derivatives. This approach not only protects the environment by improving water quality, it also encourages large flow restaurant operators to recycle oil and grease content towards cleaner production.

Effective Utilization of Information and Communication Technology (ICT) for Sustainable Manpower Development among Computer Educators in Colleges of Education in South East Geo-Political Zone of Nigeria

ERIC Educational Resources Information Center

Olelewe, Chijioke Jonathan; Amaka, Eugenia Ngozi

2011-01-01

The challenges for TVET today is to re-orient and redirect its curricula to imbue trainers and trainees on sustainable use of resources to enhance appropriate work skill development as new and employment opportunities emerge such as recycling, ICT, repair, waste management, etc. This paper is therefore focused on the effective utilization of ICT…

Comprehensive process for the recovery of value and critical materials from electronic waste

DOE PAGES

Diaz, Luis A.; Lister, Tedd E.; Parkman, Jacob A.; ...

2016-04-08

The development of technologies that contribute to the proper disposal and treatment of electronic waste is not just an environmental need, but an opportunity for the recovery and recycle of valuable metals and critical materials. Value elements in electronic waste include gold, palladium, silver, copper, nickel, and rare earth elements (RE). Here, we present the development of a process that enables efficient recycling of metals from scrap mobile electronics. An electro recycling (ER) process, based on the regeneration of Fe 3+ as a weak oxidizer, is studied for the selective recovery of base metals while leaving precious metals for separatemore » extraction at reduced chemical demand. A separate process recovers rare earth oxides from magnets in electronics. Furthermore, recovery and extraction efficiencies ca. 90 % were obtained for the extraction of base metals from the non-ferromagnetic fraction in the two different solution matrices tested (H 2SO 4, and HCl). The effect of the pre-extraction of base metals in the increase of precious metals extraction efficiency was verified. On the other hand, the extraction of rare earths from the ferromagnetic fraction, performed by means of anaerobic extraction in acid media, was assessed for the selective recovery of rare earths. We developed a comprehensive flow sheet to process electronic waste to value products.« less

Recycling of nonmetallics

USGS Publications Warehouse

Amey, E.B.; Kelly, T.D.

1996-01-01

The first factor determining recyclability is the composition of the material itself. Metals, for example, can be reused with little or no loss in quality. Paper and rubber, by this criterion, are less recyclable. Each time paper is recycled, some cellulose fibers are broken. Shorter fibers can mean weaker paper of perceived lower quality and value. Vulcanizing is an irreversible chemical process that precludes recycling rubber in its original form. Both materials may be reused in other applications often of lower value than the original one. To be recyclable, the discarded material must have a collection infrastructure at the source of waste generation, at a central collection site, or at curbside. The recovered material must also have a market. If it is priced noncompetitively or no market exists, if it does not meet specifications, or if it requires special technology investments which cannot be recovered through future sales, the recovered material may be stockpiled or discarded rather than recycled. ?? 1996 International Association for Mathematical Geology.

Research on automated disassembly technology for waste LCD

NASA Astrophysics Data System (ADS)

Qin, Qin; Zhu, Dongdong; Wang, Jingwei; Dou, Jianfang; Wang, Sujuan; Tu, Zimei

2017-11-01

In the field of Waste LCD disassembling and recycling, there are existing two major problems: 1) disassembling waste LCD mainly depends on manually mechanical crushing; 2) the resource level is not high. In order to deal with the above problems, in this paper, we develop an efficient, safe and automated waste LCD disassembling assembly line technology. This technology can disassembly and classify mainstream LCD into four components, which are liquid crystal display panels, housings and metal shield, PCB assembly. It can also disassembly many kinds of waste LCD. Compared with the traditional cooperation of manual labor and electric tools method, our proposed technology can significantly improve disassembling efficiency and demonstrate good prospects and promotional value.

Research on Durability of Big Recycled Aggregate Self-Compacting Concrete Beam

NASA Astrophysics Data System (ADS)

Gao, Shuai; Liu, Xuliang; Li, Jing; Li, Juan; Wang, Chang; Zheng, Jinkai

2018-03-01

Deflection and crack width are the most important durability indexes, which play a pivotal role in the popularization and application of the Big Recycled Aggregate Self-Compacting Concrete technology. In this research, comparative study on the Big Recycled Aggregate Self-Compacting Concrete Beam and ordinary concrete beam were conducted by measuring the deflection and crack width index. The results show that both kind of concrete beams have almost equal mid-span deflection value and are slightly different in the maximum crack width. It indicates that the Big Recycled Aggregate Self-Compacting Concrete Beam will be a good substitute for ordinary concrete beam in some less critical structure projects.

Physical properties of recycled PET non-woven fabrics for buildings

NASA Astrophysics Data System (ADS)

Üstün Çetin, S.; Tayyar, A. E.

2017-10-01

Recycled fibers have been commonly used in non-woven production technology for engineering applications such as textile engineering and civil engineering. Nonwovens including recycled fibers can be utilized in insulation, roofing and floor separation applications. In this study, physical performance properties such as drape, bending resistance, tensile strength, and breaking elongation values of non-woven fabrics consisting of v-PET (virgin) and r-PET (recycled) fibers in five different blend ratios are examined comparatively. The test results indicated that r-PET can be used in non-wovens for civil engineering applications such as insulation, roofing and floor separation fulfilling the acceptable quality level values.

Ammonium nitrogen removal from coking wastewater by chemical precipitation recycle technology.

PubMed

Zhang, Tao; Ding, Lili; Ren, Hongqiang; Xiong, Xiang

2009-12-01

Ammonium nitrogen removal from wastewater has been of considerable concern for several decades. In the present research, we examined chemical precipitation recycle technology (CPRT) for ammonium nitrogen removal from coking wastewater. The pyrolysate resulting from magnesium ammonium phosphate (MAP) pyrogenation in sodium hydroxide (NaOH) solution was recycled for ammonium nitrogen removal from coking wastewater. The objective of this study was to investigate the conditions for MAP pyrogenation and to characterize of MAP pyrolysate for its feasibility in recycling. Furthermore, MAP pyrolysate was characterized by scanning electron microscope (FESEM), transmission electron microscope (TEM), Fourier transform infrared spectroscopy (FTIR) as well as X-ray diffraction (XRD). The MAP pyrolysate could be produced at the optimal condition of a hydroxyl (OH(-)) to ammonium molar ratio of 2:1, a heating temperature of 110 degrees C, and a heating time of 3h. Surface characterization analysis indicated that the main component of the pyrolysate was amorphous magnesium sodium phosphate (MgNaPO(4)). The pyrolysate could be recycled as a magnesium and phosphate source at an optimum pH of 9.5. When the recycle times were increased, the ammonium nitrogen removal ratio gradually decreased if the pyrolysate was used without supplementation. When the recycle times were increased, the ammonium nitrogen removal efficiency was not decreased if the added pyrolysate was supplemented with MgCl(2).6H(2)O plus Na(2)HPO(4).12H(2)O during treatment. A high ammonium nitrogen removal ratio was obtained by using pre-formed MAP as seeding material.

Recycling evaluation of new-generation environmentally benign pressure sensitive adhesives

Treesearch

Said M. Abubakr; Carl Houtman; Dave Bormett; Nancy Ross Sutherland; Joe Peng

1999-01-01

As a result of a United States Postal Service (USPS) initiative, a work team was formed consisting of representatives from USPS, Forest Products Laboratory (FPL), Specialized Technology Resources, Inc. (STR), and industry. The industries represented included papermakers, paper recyclers, paper collectors, equipment manufacturers, paper users, adhesive manufacturers and...

CONTROL TECHNOLOGIES FOR REMEDIATION OF CONTAMINATED SOIL AND WASTE DEPOSITS AT SUPERFUND LEAD BATTERY RECYCLING SITES

EPA Science Inventory

This paper primarily addresses remediation of contaminated soils and waste deposits at defunct lead-acid battery recycling sites (LBRS) via immobilization and separation processes. A defunct LBRS is a facility at which battery breaking, secondary lead smelting, or both operations...

Recycling, Thermodynamics and Environmental Thrift

ERIC Educational Resources Information Center

Berry, R. Stephen

1972-01-01

Compares the cost, in terms of thermodynamic potential, of manufacturing automobiles from raw mineral resources or from recycled vehicles, and of the production of extended-life products. Uses this as an example for arguing that new technologies, with efficiencies closer to the theoretical themodynamic minima, are needed if a society is to…

Water Purification Systems

NASA Technical Reports Server (NTRS)

1994-01-01

Clearwater Pool Technologies employs NASA-developed silver/copper ionization to purify turtle and dolphin tanks, cooling towers, spas, water recycling systems, etc. The pool purifier consists of a microcomputer to monitor water conditions, a pair of metallic electrodes, and a rheostat controller. Ions are generated by passing a low voltage current through the electrodes; the silver ions kill the bacteria, and the copper ions kill algae. This technology has found broad application because it offers an alternative to chemical disinfectants. It was originally developed to purify water on Apollo spacecraft. Caribbean Clear has been using NASA's silver ionization technology for water purification for more than a decade. Two new products incorporate advancements of the basic technology. One is the AquaKing, a system designed for areas with no source of acceptable drinking water. Another is the Caribbean Clear Controller, designed for commercial pool and water park applications where sanitizing is combined with feedback control of pH and an oxidizer, chlorine or bromine. The technology was originally developed to purify water on Apollo spacecraft.

Cryopolymers

NASA Technical Reports Server (NTRS)

1995-01-01

NASA's Technology Transfer Office (TTO) at Stennis Space Center worked with a small tire recycling company, Cryopolymers, Inc. in St. Francisville, La., to improve its process for recycling used tires. Stennis helped Cryopolymers make better use of the cryogens, or super-cold fluids, used in its recycling process. First, the tires are frozen, then broken down and made into a material called 'crumb,' which can be used in asphalt road beds, agricultural hoses, and truck bed liners. TTO based this assistance on NASA's experience using cryogens in the testing of Space Shuttle Main Engines.

Testing of advanced liquefaction concepts in HTI Run ALC-1: Coal cleaning and recycle solvent treatment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robbins, G.A.; Winschel, R.A.; Burke, F.P.

In 1991, the Department of Energy initiated the Advanced Liquefaction Concepts Program to promote the development of new and emerging technology that has potential to reduce the cost of producing liquid fuels by direct coal liquefaction. Laboratory research performed by researchers at CAER, CONSOL, Sandia, and LDP Associates in Phase I is being developed further and tested at the bench scale at HTI. HTI Run ALC-1, conducted in the spring of 1996, was the first of four planned tests. In Run ALC-1, feed coal ash reduction (coal cleaning) by oil agglomeration, and recycle solvent quality improvement through dewaxing and hydrotreatmentmore » of the recycle distillate were evaluated. HTI`s bench liquefaction Run ALC-1 consisted of 25 days of operation. Major accomplishments were: 1) oil agglomeration reduced the ash content of Black Thunder Mine coal by 40%, from 5.5% to 3.3%; 2) excellent coal conversion of 98% was obtained with oil agglomerated coal, about 3% higher than the raw Black Thunder Mine coal, increasing the potential product yield by 2-3% on an MAF coal basis; 3) agglomerates were liquefied with no handling problems; 4) fresh catalyst make-up rate was decreased by 30%, with no apparent detrimental operating characteristics, both when agglomerates were fed and when raw coal was fed (with solvent dewaxing and hydrotreating); 5) recycle solvent treatment by dewaxing and hydrotreating was demonstrated, but steady-state operation was not achieved; and 6) there was some success in achieving extinction recycle of the heaviest liquid products. Performance data have not been finalized; they will be available for full evaluation in the new future.« less

Early repositioning through compound set enrichment analysis: a knowledge-recycling strategy.

PubMed

Temesi, Gergely; Bolgár, Bence; Arany, Adám; Szalai, Csaba; Antal, Péter; Mátyus, Péter

2014-04-01

Despite famous serendipitous drug repositioning success stories, systematic projects have not yet delivered the expected results. However, repositioning technologies are gaining ground in different phases of routine drug development, together with new adaptive strategies. We demonstrate the power of the compound information pool, the ever-growing heterogeneous information repertoire of approved drugs and candidates as an invaluable catalyzer in this transition. Systematic, computational utilization of this information pool for candidates in early phases is an open research problem; we propose a novel application of the enrichment analysis statistical framework for fusion of this information pool, specifically for the prediction of indications. Pharmaceutical consequences are formulated for a systematic and continuous knowledge recycling strategy, utilizing this information pool throughout the drug-discovery pipeline.

Final Technical Report for EE0006091: H2Pump Hydrogen Recycling System Demonstration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Staudt, Rhonda

The objective of this project is to demonstrate the product readiness and to quantify the benefits and customer value proposition of H2Pump’s Hydrogen Recycling System (HRS-100™) by installing and analyzing the operation of multiple prototype 100-kg per day systems in real world customer locations. The data gathered will be used to measure reliability, demonstrate the value proposition to customers, and validate our business model. H2Pump will install, track and report multiple field demonstration systems in industrial heat treating and semi-conductor applications. The customer demonstrations will be used to develop case studies and showcase the benefits of the technology to drivemore » market adoption.« less

Novel Fast Pyrolysis/Catalytic Technology for the Production of Stable Upgraded Liquids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oyama, Ted; Agblevor, Foster; Battaglia, Francine

The objective of the proposed research is the demonstration and development of a novel biomass pyrolysis technology for the production of a stable bio-oil. The approach is to carry out catalytic hydrodeoxygenation (HDO) and upgrading together with pyrolysis in a single fluidized bed reactor with a unique two-level design that permits the physical separation of the two processes. The hydrogen required for the HDO will be generated in the catalytic section by the water-gas shift reaction employing recycled CO produced from the pyrolysis reaction itself. Thus, the use of a reactive recycle stream is another innovation in this technology. Themore » catalysts will be designed in collaboration with BASF Catalysts LLC (formerly Engelhard Corporation), a leader in the manufacture of attrition-resistant cracking catalysts. The proposed work will include reactor modeling with state-of-the-art computational fluid dynamics in a supercomputer, and advanced kinetic analysis for optimization of bio-oil production. The stability of the bio-oil will be determined by viscosity, oxygen content, and acidity determinations in real and accelerated measurements. A multi-faceted team has been assembled to handle laboratory demonstration studies and computational analysis for optimization and scaleup.« less

Toward environmentally-benign utilization of nonmetallic fraction of waste printed circuit boards as modifier and precursor.

PubMed

Hadi, Pejman; Ning, Chao; Ouyang, Weiyi; Xu, Meng; Lin, Carol S K; McKay, Gordon

2015-01-01

Electronic waste, including printed circuit boards, is growing at an alarming rate due to the accelerated technological progress and the shorter lifespan of the electronic equipment. In the past decades, due to the lack of proper economic and environmentally-benign recycling technologies, a major fraction of e-waste generated was either destined to landfills or incinerated with the sole intention of its disposal disregarding the toxic nature of this waste. Recently, with the increasing public awareness over their environment and health issues and with the enaction of more stringent regulations, environmentally-benign recycling has been driven to be an alternative option partially replacing the traditional eco-unfriendly disposal methods. One of the most favorable green technologies has been the mechanical separation of the metallic and nonmetallic fraction of the waste printed circuit boards. Although metallic fraction, as the most profitable component, is used to generate the revenue of the separation process, the nonmetallic fraction (NMF) has been left isolated. Herein, the recent developments in the application of NMF have been comprehensively reviewed and an eco-friendly emerging usage of NMF as a value-added material for sustainable remediation has been introduced. Copyright © 2014 Elsevier Ltd. All rights reserved.

Aerospace Fuels From Nonpetroleum Raw Materials

NASA Technical Reports Server (NTRS)

Palaszewski, Bryan A.; Hepp, Aloysius F.; Kulis, Michael J.; Jaworske, Donald A.

2013-01-01

Recycling human metabolic and plastic wastes minimizes cost and increases efficiency by reducing the need to transport consumables and return trash, respectively, from orbit to support a space station crew. If the much larger costs of transporting consumables to the Moon and beyond are taken into account, developing waste recycling technologies becomes imperative and possibly mission enabling. Reduction of terrestrial waste streams while producing energy and/or valuable raw materials is an opportunity being realized by a new generation of visionary entrepreneurs; several relevant technologies are briefly compared, contrasted and assessed for space applications. A two-step approach to nonpetroleum raw materials utilization is presented; the first step involves production of supply or producer gas. This is akin to synthesis gas containing carbon oxides, hydrogen, and simple hydrocarbons. The second step involves production of fuel via the Sabatier process, a methanation reaction, or another gas-to-liquid technology, typically Fischer-Tropsch processing. Optimization to enhance the fraction of product stream relevant to transportation fuels via catalytic (process) development at NASA Glenn Research Center is described. Energy utilization is a concern for production of fuels whether for operation on the lunar or Martian surface, or beyond. The term green relates to not only mitigating excess carbon release but also to the efficiency of energy usage. For space, energy usage can be an essential concern. Another issue of great concern is minimizing impurities in the product stream(s), especially those that are potential health risks and/or could degrade operations through catalyst poisoning or equipment damage; technologies being developed to remove heteroatom impurities are discussed. Alternative technologies to utilize waste fluids, such as a propulsion option called the resistojet, are discussed. The resistojet is an electric propulsion technology with a powered thruster to vaporize and heat a propellant to high temperature, hot gases are subsequently passed through a converging-diverging nozzle expanding gases to supersonic velocities. A resistojet can accommodate many different fluids, including various reaction chamber (by-)products.

Aerospace Fuels from Nonpetroleum Raw Materials

NASA Technical Reports Server (NTRS)

Palaszewski, B. A.; Hepp, A. F.; Kulis, M. J.; Jaworske, D. A.

2013-01-01

Recycling human metabolic and plastic wastes minimizes cost and increases efficiency by reducing the need to transport consumables and return trash, respectively, from orbit to support a space station crew. If the much larger costs of transporting consumables to the Moon and beyond are taken into account, developing waste recycling technologies becomes imperative and possibly mission enabling. Reduction of terrestrial waste streams while producing energy and/or valuable raw materials is an opportunity being realized by a new generation of visionary entrepreneurs; several relevant technologies are briefly compared, contrasted and assessed for space applications. A two-step approach to nonpetroleum raw materials utilization is presented; the first step involves production of supply or producer gas. This is akin to synthesis gas containing carbon oxides, hydrogen, and simple hydrocarbons. The second step involves production of fuel via the Sabatier process, a methanation reaction, or another gas-to-liquid technology, typically Fischer- Tropsch processing. Optimization to enhance the fraction of product stream relevant to transportation fuels via catalytic (process) development at NASA GRC is described. Energy utilization is a concern for production of fuels whether for operation on the lunar or Martian surface, or beyond. The term "green" relates to not only mitigating excess carbon release but also to the efficiency of energy usage. For space, energy usage can be an essential concern. Other issues of great concern include minimizing impurities in the product stream(s), especially those that are potential health risks and/or could de-grade operations through catalyst poisoning or equipment damage; technologies being developed to remove heteroatom impurities are discussed. Alternative technologies to utilize waste fluids, such as a propulsion option called the resistojet, are discussed. The resistojet is an electric propulsion technology with a powered thruster to vaporize and heat a propellant to high temperature, hot gases are subsequently passed through a converging-diverging nozzle expanding gases to supersonic velocities. A resistojet can accommodate many different fluids, including various reaction chamber (by-)products.

Design of platform for removing screws from LCD display shields

NASA Astrophysics Data System (ADS)

Tu, Zimei; Qin, Qin; Dou, Jianfang; Zhu, Dongdong

2017-11-01

Removing the screws on the sides of a shield is a necessary process in disassembling a computer LCD display. To solve this issue, a platform has been designed for removing the screws on display shields. This platform uses virtual instrument technology with LabVIEW as the development environment to design the mechanical structure with the technologies of motion control, human-computer interaction and target recognition. This platform removes the screws from the sides of the shield of an LCD display mechanically thus to guarantee follow-up separation and recycle.

Developing Markets for Recycled Products: Demand Lags behind Supply.

ERIC Educational Resources Information Center

Lewis, Eleanor J.; Weltman, Eric

1992-01-01

Colleges and universities are saving their recyclables for collection, but paying less attention to developing markets for recycled materials. Institutions can help by purchasing recycled paper. Costs can be reduced through contract and consortium buying and user conservation measures. (MSE)

QuEST: Qualifying Environmentally Sustainable Technologies

NASA Technical Reports Server (NTRS)

Lewis, Pattie

2012-01-01

Articles in this issue inlude: (1) Foundation of Technology Evaluation for Environmental Risk Mitigation Principal Center (TEERM) Technology Evaluation is Testing and Qualification, (2) Materials Management and Substitution Efforts, (3 Recycling and Pollution Control Efforts, and (4) Remediation Efforts

GUIDE TO CLEANER TECHNOLOGIES: ORGANIC COATING REMOVAL

EPA Science Inventory

A cleaner technology is a source reduction or recycle method |applied to eliminate or significantly reduce hazardous waste generation. Source reduction includes product changes and source control. Source control can be further characterized as input material changes, technology...

Current status of urban wastewater treatment plants in China.

PubMed

Zhang, Q H; Yang, W N; Ngo, H H; Guo, W S; Jin, P K; Dzakpasu, Mawuli; Yang, S J; Wang, Q; Wang, X C; Ao, D

2016-01-01

The study reported and analyzed the current state of wastewater treatment plants (WWTPs) in urban China from the perspective of treatment technologies, pollutant removals, operating load and effluent discharge standards. By the end of 2013, 3508 WWTPs have been built in 31 provinces and cities in China with a total treatment capacity of 1.48×10(8)m(3)/d. The uneven population distribution between China's east and west regions has resulted in notably different economic development outcomes. The technologies mostly used in WWTPs are AAO and oxidation ditch, which account for over 50% of the existing WWTPs. According to statistics, the efficiencies of COD and NH3-N removal are good in 656 WWTPs in 70 cities. The overall average COD removal is over 88% with few regional differences. The average removal efficiency of NH3-N is up to 80%. Large differences exist between the operating loads applied in different WWTPs. The average operating loading rate is approximately 83%, and 52% of WWTPs operate at loadings of <80%, treating up to 40% of the wastewater generated. The implementation of discharge standards has been low. Approximately 28% of WWTPs that achieved the Grade I-A Discharge Standard of Pollutants for Municipal Wastewater Treatment Plant (GB 18918-2002) were constructed after 2010. The sludge treatment and recycling rates are only 25%, and approximately 15% of wastewater is inefficiently treated. Approximately 60% of WWTPs have capacities of 1×10(4)m(3)/d-5×10(4)m(3)/d. Relatively high energy consumption is required for small-scale processing, and the utilization rate of recycled wastewater is low. The challenges of WWTPs are discussed with the aim of developing rational criteria and appropriate technologies for water recycling. Suggestions regarding potential technical and administrative measures are provided. Copyright © 2016 Elsevier Ltd. All rights reserved.

Novel Catalysts and Processing Technologies for Production of Aerospace Fuels from Non-Petroleum Raw Materials

NASA Technical Reports Server (NTRS)

Hepp, Aloysius F.; Kulis, Michael J.; Psarras, Peter C.; Ball, David W.; Timko, Michael T.; Wong, Hsi-Wu; Peck, Jay; Chianelli, Russell R.

2014-01-01

Transportation fuels production (including aerospace propellants) from non-traditional sources (gases, waste materials, and biomass) has been an active area of research and development for decades. Reducing terrestrial waste streams simultaneous with energy conversion, plentiful biomass, new low-cost methane sources, and/or extra-terrestrial resource harvesting and utilization present significant technological and business opportunities being realized by a new generation of visionary entrepreneurs. We examine several new approaches to catalyst fabrication and new processing technologies to enable utilization of these nontraditional raw materials. Two basic processing architectures are considered: a single-stage pyrolysis approach that seeks to basically re-cycle hydrocarbons with minimal net chemistry or a two-step paradigm that involves production of supply or synthesis gas (mainly carbon oxides and H2) followed by production of fuel(s) via Sabatier or methanation reactions and/or Fischer-Tröpsch synthesis. Optimizing the fraction of product stream relevant to targeted aerospace (and other transportation) fuels via modeling, catalyst fabrication and novel reactor design are described. Energy utilization is a concern for production of fuels for either terrestrial or space operations; renewable sources based on solar energy and/or energy efficient processes may be mission enabling. Another important issue is minimizing impurities in the product stream(s), especially those potentially posing risks to personnel or operations through (catalyst) poisoning or (equipment) damage. Technologies being developed to remove (and/or recycle) heteroatom impurities are briefly discussed as well as the development of chemically robust catalysts whose activities are not diminished during operation. The potential impacts on future missions by such new approaches as well as balance of system issues are addressed.

Novel Catalysts and Processing Technologies for Production of Aerospace Fuels from Non-Petroleum Raw Materials

NASA Technical Reports Server (NTRS)

Hepp, A. F.; Kulis, M. J.; Psarras, P. C.; Ball, D. W.; Timko, M. T.; Wong, H.-W.; Peck, J.; Chianelli, R. R.

2014-01-01

Transportation fuels production (including aerospace propellants) from non-traditional sources (gases, waste materials, and biomass) has been an active area of research and development for decades. Reducing terrestrial waste streams simultaneous with energy conversion, plentiful biomass, new low-cost methane sources, and/or extra-terrestrial resource harvesting and utilization present significant technological and business opportunities being realized by a new generation of visionary entrepreneurs. We examine several new approaches to catalyst fabrication and new processing technologies to enable utilization of these non-traditional raw materials. Two basic processing architectures are considered: a single-stage pyrolysis approach that seeks to basically re-cycle hydrocarbons with minimal net chemistry or a two-step paradigm that involves production of supply or synthesis gas (mainly carbon oxides and hydrogen) followed by production of fuel(s) via Sabatier or methanation reactions and/or Fischer-Tropsch synthesis. Optimizing the fraction of product stream relevant to targeted aerospace (and other transportation) fuels via modeling, catalyst fabrication and novel reactor design are described. Energy utilization is a concern for production of fuels for either terrestrial or space operations; renewable sources based on solar energy and/or energy efficient processes may be mission enabling. Another important issue is minimizing impurities in the product stream(s), especially those potentially posing risks to personnel or operations through (catalyst) poisoning or (equipment) damage. Technologies being developed to remove (and/or recycle) heteroatom impurities are briefly discussed as well as the development of chemically robust catalysts whose activity are not diminished during operation. The potential impacts on future missions by such new approaches as well as balance of system issues are addressed.

DU Processing Efficiency and Reclamation: Plasma Arc Melting

DOE Office of Scientific and Technical Information (OSTI.GOV)

Imhoff, Seth D.; Aikin, Jr., Robert M.; Swenson, Hunter

The work described here corresponds to one piece of a larger effort to increase material usage efficiency during DU processing operations. In order to achieve this goal, multiple technologies and approaches are being tested. These technologies occupy a spectrum of technology readiness levels (TRLs). Plasma arc melting (PAM) is one of the technologies being investigated. PAM utilizes a high temperature plasma to melt materials. Depending on process conditions, there are potential opportunities for recycling and material reclamation. When last routinely operational, the LANL research PAM showed extremely promising results for recycling and reclamation of DU and DU alloys. The currentmore » TRL is lower due to machine idleness for nearly two decades, which has proved difficult to restart. This report describes the existing results, promising techniques, and the process of bringing this technology back to readiness at LANL.« less

Clinical solid waste management practices and its impact on human health and environment - A review

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hossain, Md. Sohrab; Santhanam, Amutha; Nik Norulaini, N.A.

2011-04-15

Research highlights: > Appropriate waste management technology for safe handling and disposal of clinical solid waste. > Infectious risk assessment on unsafe handling of clinical solid waste. > Recycling-reuse program of clinical solid waste materials. > Effective sterilization technology to reduce exposure of infectious risk. - Abstract: The management of clinical solid waste (CSW) continues to be a major challenge, particularly, in most healthcare facilities of the developing world. Poor conduct and inappropriate disposal methods exercised during handling and disposal of CSW is increasing significant health hazards and environmental pollution due to the infectious nature of the waste. This articlemore » summarises a literature review into existing CSW management practices in the healthcare centers. The information gathered in this paper has been derived from the desk study of open literature survey. Numerous researches have been conducted on the management of CSW. Although, significant steps have been taken on matters related to safe handling and disposal of the clinical waste, but improper management practice is evident from the point of initial collection to the final disposal. In most cases, the main reasons of the mismanagement of CSW are the lack of appropriate legislation, lack of specialized clinical staffs, lack of awareness and effective control. Furthermore, most of the healthcare centers of the developing world have faced financial difficulties and therefore looking for cost effective disposal methods of clinical waste. This paper emphasizes to continue the recycle-reuse program of CSW materials after sterilization by using supercritical fluid carbon dioxide (SF-CO2) sterilization technology at the point of initial collection. Emphasis is on the priority to inactivate the infectious micro-organisms in CSW. In that case, waste would not pose any threat to healthcare workers. The recycling-reuse program would be carried out successfully with the non-specialized clinical staffs. Therefore, the adoption of SF-CO2 sterilization technology in management of clinical solid waste can reduce exposure to infectious waste, decrease labor, lower costs, and yield better compliance with regulatory. Thus healthcare facilities can both save money and provide a safe environment for patients, healthcare staffs and clinical staffs.« less

An international perspective on hazardous waste practices.

PubMed

Orloff, Kenneth; Falk, Henry

2003-08-01

In developing countries, public health attention is focused on urgent health problems such as infectious diseases, malnutrition, and infant mortality. As a country develops and gains economic resources, more attention is directed to health concerns related to hazardous chemical wastes. Even if a country has little industry of its own that generates hazardous wastes, the importation of hazardous wastes for recycling or disposal can present health hazards. It is difficult to compare the quantities of hazardous wastes produced in different countries because of differences in how hazardous wastes are defined. In most countries, landfilling is the most common means of hazardous waste disposal, although substantial quantities of hazardous wastes are incinerated in some countries. Hazardous wastes that escape into the environment most often impact the public through air and water contamination. An effective strategy for managing hazardous wastes should encourage waste minimization, recycling, and reuse over disposal. Developing countries are especially in need of low-cost technologies for managing hazardous wastes.

Quantifying pretreatment degradation compounds in solution and accumulated by cells during solids and yeast recycling in the Rapid Bioconversion with Integrated recycling Technology process using AFEX™ corn stover.

PubMed

Sarks, Cory; Higbee, Alan; Piotrowski, Jeff; Xue, Saisi; Coon, Joshua J; Sato, Trey K; Jin, Mingjie; Balan, Venkatesh; Dale, Bruce E

2016-04-01

Effects of degradation products (low molecular weight compounds produced during pretreatment) on the microbes used in the RaBIT (Rapid Bioconversion with Integrated recycling Technology) process that reduces enzyme usage up to 40% by efficient enzyme recycling were studied. Chemical genomic profiling was performed, showing no yeast response differences in hydrolysates produced during RaBIT enzymatic hydrolysis. Concentrations of degradation products in solution were quantified after different enzymatic hydrolysis cycles and fermentation cycles. Intracellular degradation product concentrations were also measured following fermentation. Degradation product concentrations in hydrolysate did not change between RaBIT enzymatic hydrolysis cycles; the cell population retained its ability to oxidize/reduce (detoxify) aldehydes over five RaBIT fermentation cycles; and degradation products accumulated within or on the cells as RaBIT fermentation cycles increased. Synthetic hydrolysate was used to confirm that pretreatment degradation products are the sole cause of decreased xylose consumption during RaBIT fermentations. Copyright © 2016 Elsevier Ltd. All rights reserved.

Developing an Advanced Life Support System for the Flexible Path into Deep Space

NASA Technical Reports Server (NTRS)

Jones, Harry W.; Kliss, Mark H.

2010-01-01

Long duration human missions beyond low Earth orbit, such as a permanent lunar base, an asteroid rendezvous, or exploring Mars, will use recycling life support systems to preclude supplying large amounts of metabolic consumables. The International Space Station (ISS) life support design provides a historic guiding basis for future systems, but both its system architecture and the subsystem technologies should be reconsidered. Different technologies for the functional subsystems have been investigated and some past alternates appear better for flexible path destinations beyond low Earth orbit. There is a need to develop more capable technologies that provide lower mass, increased closure, and higher reliability. A major objective of redesigning the life support system for the flexible path is achieving the maintainability and ultra-reliability necessary for deep space operations.

ENGINEERING BULLETIN: SELECTION OF CONTROL TECHNOLOGIES FOR REMEDIATION OF LEAD BATTERY RECYCLING SITES

EPA Science Inventory

Section 121(b) of the Comprehensive Environmental Response, Compensation, and Liability Act, (CERCLA) mandates the Environmental Protection Agency (EPA) to select remedies that "utilize permanent solutions and alternative treatment technologies or resource recovery technologies ...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chynoweth, E.; Young, I.

The plastics recycling debate quite literally took center stage at the K '92 international plastics fair. Leading figures of the European plastic industry, including Jacques Puechal, chairman of Elf Atochem and president of the European Chemical Industry Council (Brussels), and Klaus Toepfer and Segolene Royal, the environment ministers of Germany and France, respectively, took part in a forum discussion in front of an audience of 600-plus. Exhibitors of K '92 managed to maintain an air of optimism at the show in spite of gloomy market conditions. A couple of firms admitted business in plastics was [open quotes]catastrophic[close quotes] and [openmore » quotes]a nightmare.[close quotes] At the forum the Association of Plastics Manufacturers in Europe (APME; Brussels), represented by its president, Dieter Cron, promoted the cascade concept to answer the plastics waste problem. This includes incineration with energy recovery in cases in which recycling is senseless economically and environmentally. Toepfer stated his wish for the period between use and final incineration to be extended through more recycling. Royal suggested that France and Germany set up a joint research program looking at the environmental impact of waste-to-energy technologies. Industry representatives, including Puechal, note the importance of developing a pan-European legal framework for recycling, because the business is international.« less

Conjectured the Behaviour of a Recycled Metal Matrix Composite (MMC⁻AlR) Developed through Hot Press Forging by Means of 3D FEM Simulation.

PubMed

Ahmad, Azlan; Lajis, Mohd Amri; Shamsudin, Shazarel; Yusuf, Nur Kamilah

2018-06-06

Melting aluminium waste to produce a secondary bulk material is such an energy-intensive recycling technique that it also indirectly threatens the environment. Hot press forging is introduced as an alternative. Mixing the waste with another substance is a proven practice that enhances the material integrity. To cope with the technology revolution, a finite element is utilised to predict the behaviour without a practical trial. Utilising commercial software, DEFORM 3D, the conjectures were demonstrated scientifically. The flow stress of the material was modified to suit the material used in the actual experiment. It is acknowledged that the stress⁻strain had gradually increased in each step. Due to the confined forming space, the temperature decreased by ~0.5% because the heat could not simply vacate the area. A reduction of ~10% of the flesh observed in the simulation is roughly the same as in the actual experiment. Above all, the simulation abides by the standards and follows what has been done previously. Through the finite element utilisation, this study forecasted the performance of the recycled composite. The results presented may facilitate improvement of the recycling issue and conserve the environment for a better future.

Recycling acetic acid from polarizing film of waste liquid crystal display panels by sub/supercritical water treatments.

PubMed

Wang, Ruixue; Chen, Ya; Xu, Zhenming

2015-05-19

Waste liquid crystal display (LCD) panels mainly contain inorganic materials (glass substrate) and organic materials (polarizing film and liquid crystal). The organic materials should be removed first since containing polarizing film and liquid crystal is to the disadvantage of the indium recycling process. In the present study, an efficient and environmentally friendly process to obtain acetic acid from waste LCD panels by sub/supercritical water treatments is investigated. Furthermore, a well-founded reaction mechanism is proposed. Several highlights of this study are summarized as follows: (i) 99.77% of organic matters are removed, which means the present technology is quite efficient to recycle the organic matters; (ii) a yield of 78.23% acetic acid, a quite important fossil energy based chemical product is obtained, which can reduce the consumption of fossil energy for producing acetic acid; (iii) supercritical water acts as an ideal solvent, a requisite reactant as well as an efficient acid-base catalyst, and this is quite significant in accordance with the "Principles of Green Chemistry". In a word, the organic matters of waste LCD panels are recycled without environmental pollution. Meanwhile, this study provides new opportunities for alternating fossil-based chemical products for sustainable development, converting "waste" into "fossil-based chemicals".

Quantifying Recycling and Losses of Cr and Ni in Steel Throughout Multiple Life Cycles Using MaTrace-Alloy.

PubMed

Nakamura, Shinichiro; Kondo, Yasushi; Nakajima, Kenichi; Ohno, Hajime; Pauliuk, Stefan

2017-09-05

Alloying metals are indispensable ingredients of high quality alloy steel such as austenitic stainless steel, the cyclical use of which is vital for sustainable resource management. Under the current practice of recycling, however, different metals are likely to be mixed in an uncontrolled manner, resulting in function losses and dissipation of metals with distinctive functions, and in the contamination of recycled steels. The latter could result in dilution loss, if metal scrap needed dilution with virgin iron to reduce the contamination below critical levels. Management of these losses resulting from mixing in repeated recycling of metals requires tracking of metals over multiple life cycles of products with compositional details. A new model (MaTrace-alloy) was developed that tracks the fate of metals embodied in each of products over multiple life cycles of products, involving accumulation, discard, and recycling, with compositional details at the level of both alloys and products. The model was implemented for the flow of Cr and Ni in the Japanese steel cycle involving 27 steel species and 115 final products. It was found that, under a high level of scrap sorting, greater than 70% of the initial functionality of Cr and Ni could be retained over a period of 100 years, whereas under a poor level of sorting, it could plunge to less than 30%, demonstrating the relevance of waste management technology in circular economy policies.

3 CFR 8601 - Proclamation 8601 of November 15, 2010. America Recycles Day, 2010

Code of Federal Regulations, 2011 CFR

2011-01-01

... planet, participating in curbside recycling and community composting programs, and expanding their use of recyclable and recycled materials. Recycling not only preserves our environment by conserving precious... development. This billion-dollar industry employs thousands of workers nationwide, and evolving our recycling...

Environmental Aspects of Use of Recycled Carbon Fiber Composites in Automotive Applications.

PubMed

Meng, Fanran; McKechnie, Jon; Turner, Thomas; Wong, Kok H; Pickering, Stephen J

2017-11-07

The high cost and energy intensity of virgin carbon fiber manufacture provides an opportunity to recover substantial value from carbon fiber reinforced plastic wastes. In this study, we assess the life cycle environmental implications of recovering carbon fiber and producing composite materials as substitutes for conventional and proposed lightweight materials in automotive applications (e.g., steel, aluminum, virgin carbon fiber). Key parameters for the recycled carbon fiber materials, including fiber volume fraction and fiber alignment, are investigated to identify beneficial uses of recycled carbon fiber in the automotive sector. Recycled carbon fiber components can achieve the lowest life cycle environmental impacts of all materials considered, although the actual impact is highly dependent on the design criteria (λ value) of the specific component. Low production impacts associated with recycled carbon fiber components are observed relative to lightweight competitor materials (e.g., aluminum, virgin carbon fiber reinforced plastic). In addition, recycled carbon fiber components have low in-use energy use due to mass reductions and associated reduction in mass-induced fuel consumption. The results demonstrate environmental feasibility of the CFRP recycling materials, supporting the emerging commercialization of CF recycling technologies and identifying significant potential market opportunities in the automotive sector.

Advancing Plug-In Hybrid Technology and Flex Fuel Application on a Chrysler Minivan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bazzi, Abdullah; Barnhart, Steven

2014-12-31

FCA US LLC viewed this DOE funding as a historic opportunity to begin the process of achieving required economies of scale on technologies for electric vehicles. The funding supported FCA US LLC’s light-duty electric drive vehicle and charging infrastructure-testing activities and enabled FCA US LLC to utilize the funding on advancing Plug-in Hybrid Electric Vehicle (PHEV) technologies to future programs. FCA US LLC intended to develop the next generations of electric drive and energy batteries through a properly paced convergence of standards, technology, components, and common modules, as well as first-responder training and battery recycling. To support the development ofmore » a strong, commercially viable supplier base, FCA US LLC also used this opportunity to evaluate various designated component and sub-system suppliers. The original project proposal was submitted in December 2009 and selected in January 2010. The project ended in December 2014.« less

Caustic Recycling Pilot Unit to Separate Sodium from LLW at Hanford Site - 12279

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pendleton, Justin; Bhavaraju, Sai; Priday, George

As part of the Department of Energy (DOE) sponsored Advanced Remediation Technologies initiative, a scheme was developed to combine Continuous Sludge Leaching (CSL), Near-Tank Cesium Removal (NTCR), and Caustic Recycling Unit (CRU) using Ceramatec technology, into a single system known as the Pilot Near-Tank Treatment System (PNTTS). The Cesium (Cs) decontaminated effluent from the NTCR process will be sent to the caustic recycle process for recovery of the caustic which will be reused in another cycle of caustic leaching in the CSL process. Such an integrated mobile technology demonstration will give DOE the option to insert this process for sodiummore » management at various sites in Hanford, and will minimize the addition of further sodium into the waste tanks. This allows for recycling of the caustic used to remove aluminum during sludge washing as a pretreatment step in the vitrification of radioactive waste which will decrease the Low Level Waste (LLW) volume by as much as 39%. The CRU pilot process was designed to recycle sodium in the form of pure sodium hydroxide. The basis for the design of the 1/4 scale pilot caustic recycling unit was to demonstrate the efficient operation of a larger scale system to recycle caustic from the NTCR effluent stream from the Parsons process. The CRU was designed to process 0.28 liter/minute of NTCR effluent, and generate 10 M concentration of 'usable' sodium hydroxide. The proposed process operates at 40 deg. C to provide additional aluminum solubility and then recover the sodium hydroxide to the point where the aluminum is saturated at 40 deg. C. A system was developed to safely separate and vent the gases generated during operation of the CRU with the production of 10 M sodium hydroxide. Caustic was produced at a rate between 1.9 to 9.3 kg/hr. The CRU was located inside an ISO container to allow for moving of the unit close to tank locations to process the LLW stream. Actual tests were conducted with the NTCR effluent simulant from the Parsons process in the CRU. The modular CRU is easily scalable as a standalone system for caustic recycling, or for NTTS integration or for use as an In-Tank Treatment System to process sodium bearing waste to meet LLW processing needs at the Hanford site. The standalone pilot operation of the CRU to recycle sodium from NTCR effluent places the technology demonstration at TRL level 6. Multiple operations were performed with the CRU to process up to 500 gallons of the NTCR effluent and demonstrate an efficient separation of up to 70 % of the sodium without solids precipitation while producing 10 M caustic. Batch mode operation was conducted to study the effects of chemistry variation, establish the processing rate, and optimize the process operating conditions to recycle caustic from the NTCR effluent. The performance of the CRU was monitored by tracking the density parameter to control the concentration of caustic produced. Different levels of sodium were separated in tests from the effluent at a fixed operating current density and temperature. The voltage of the modules remained stable during the unit operation which demonstrated steady operation to separate sodium from the NTCR effluent. The sodium transfer current efficiency was measured in testing based on the concentration of caustic produced. Measurements showed a current efficiency of 99.8% for sodium transfer from the NTCR effluent to make sodium hydroxide. The sodium and hydroxide contents of the anolyte (NTCR feed) and catholyte (caustic product) were measured before and after each batch test. In two separate batch tests, samples were taken at different levels of sodium separation and analyzed to determine the stability of the NTCR effluent after sodium separation. The stability characteristics and changes in physical and chemical properties of the NTCR effluent chemistry after separation of sodium hydroxide as a function of storage time were evaluated. Parameters such as level of precipitated alumina, total alkalinity, analysis of Al, Na, K, Cs, Fe, OH, nitrate, nitrite, total dissolved and undissolved solids, viscosity, density, and other parameters of the NTCR effluent were measured. Changes in rheology and properties of NTCR stream to support downstream handling of the effluent after sodium separation was the basis for the analysis. The results show that the NTCR effluent is stable without the precipitation of aluminum hydroxide after 70% of the sodium was separated from the effluent. (authors)« less

GUIDE TO CLEANER TECHNOLOGIES: ALTERNATIVE METAL FINISHES

EPA Science Inventory

A cleaner technology is a source reduction or recycle method applied to eliminate or significantly reduce the amount of any hazardous substance, pollutant, or contaminant released to the environment. The emphasis of cleaner technologies is on process changes that can prevent poll...

Compressive strength and resistance to chloride ion penetration and carbonation of recycled aggregate concrete with varying amount of fly ash and fine recycled aggregate.

PubMed

Sim, Jongsung; Park, Cheolwoo

2011-11-01

Construction and demolition waste has been dramatically increased in the last decade, and social and environmental concerns on the recycling have consequently been increased. Recent technology has greatly improved the recycling process for waste concrete. This study investigates the fundamental characteristics of concrete using recycled concrete aggregate (RCA) for its application to structural concrete members. The specimens used 100% coarse RCA, various replacement levels of natural aggregate with fine RCA, and several levels of fly ash addition. Compressive strength of mortar and concrete which used RCA gradually decreased as the amount of the recycled materials increased. Regardless of curing conditions and fly ash addition, the 28 days strength of the recycled aggregate concrete was greater than the design strength, 40 MPa, with a complete replacement of coarse aggregate and a replacement level of natural fine aggregate by fine RCA up to 60%. The recycled aggregate concrete achieved sufficient resistance to the chloride ion penetration. The measured carbonation depth did not indicate a clear relationship to the fine RCA replacement ratio but the recycled aggregate concrete could also attain adequate carbonation resistance. Based on the results from the experimental investigations, it is believed that the recycled aggregate concrete can be successfully applied to structural concrete members. Copyright © 2011 Elsevier Ltd. All rights reserved.

Recycled poly(ethylene terephthalate) for direct food contact applications: challenge test of an inline recycling process.

PubMed

Franz, R; Welle, F

2002-05-01

Of all the plastics used for packaging, due to its low diffusivity and chemical inertness, poly(ethylene terephthalate) (PET) is one of the favoured candidate plastics for closed-loop recycling for new packaging applications. In the work reported here, a PET-recycling process was investigated with respect to its cleaning efficiency and compliance of the PET recyclate with food law. The key technology of the investigated PET-recycling process to remove contaminants consists of a predecontamination-extruder combination. At the end of the recycling process, there is either a pelletizing system or downstream equipment to produce preforms or flat sheets. Therefore, the process has two process options, an inline production of PET preforms and a batch option producing PET pellets. In the case of possible misuse of PET bottles by the consumer, the inline process produces higher concentrations in the bottle wall of the recyclate containing preforms. Owing to the dilution of the PET output material by large amounts of uncontaminated PET, the batch option is the less critical process in terms of consumer protection. Regarding an appropriate testing procedure for the evaluation of a bottle-to-bottle recycling process, both process options have their own specific requirements with respect to the design of a challenge test. A novel challenge test approach to the inline mode of a recycling process is presented here.

Mineral supply for sustainable development requires resource governance.

PubMed

Ali, Saleem H; Giurco, Damien; Arndt, Nicholas; Nickless, Edmund; Brown, Graham; Demetriades, Alecos; Durrheim, Ray; Enriquez, Maria Amélia; Kinnaird, Judith; Littleboy, Anna; Meinert, Lawrence D; Oberhänsli, Roland; Salem, Janet; Schodde, Richard; Schneider, Gabi; Vidal, Olivier; Yakovleva, Natalia

2017-03-15

Successful delivery of the United Nations sustainable development goals and implementation of the Paris Agreement requires technologies that utilize a wide range of minerals in vast quantities. Metal recycling and technological change will contribute to sustaining supply, but mining must continue and grow for the foreseeable future to ensure that such minerals remain available to industry. New links are needed between existing institutional frameworks to oversee responsible sourcing of minerals, trajectories for mineral exploration, environmental practices, and consumer awareness of the effects of consumption. Here we present, through analysis of a comprehensive set of data and demand forecasts, an interdisciplinary perspective on how best to ensure ecologically viable continuity of global mineral supply over the coming decades.

Mineral supply for sustainable development requires resource governance

USGS Publications Warehouse

Ali, Saleem H.; Giurco, Damien; Arndt, Nicholas; Nickless, Edmund; Brown, Graham; Demetriades, Alecos; Durrheim, Ray; Enriquez, Maria Amélia; Kinnaird, Judith; Littleboy, Anna; Meinert, Lawrence D.; Oberhänsli, Roland; Salem, Janet; Schodde, Richard; Schneider, Gabi; Vidal, Olivier; Yakovleva, Natalia

2017-01-01

Successful delivery of the United Nations sustainable development goals and implementation of the Paris Agreement requires technologies that utilize a wide range of minerals in vast quantities. Metal recycling and technological change will contribute to sustaining supply, but mining must continue and grow for the foreseeable future to ensure that such minerals remain available to industry. New links are needed between existing institutional frameworks to oversee responsible sourcing of minerals, trajectories for mineral exploration, environmental practices, and consumer awareness of the effects of consumption. Here we present, through analysis of a comprehensive set of data and demand forecasts, an interdisciplinary perspective on how best to ensure ecologically viable continuity of global mineral supply over the coming decades.

Mineral supply for sustainable development requires resource governance

NASA Astrophysics Data System (ADS)

Ali, Saleem H.; Giurco, Damien; Arndt, Nicholas; Nickless, Edmund; Brown, Graham; Demetriades, Alecos; Durrheim, Ray; Enriquez, Maria Amélia; Kinnaird, Judith; Littleboy, Anna; Meinert, Lawrence D.; Oberhänsli, Roland; Salem, Janet; Schodde, Richard; Schneider, Gabi; Vidal, Olivier; Yakovleva, Natalia

2017-03-01

Successful delivery of the United Nations sustainable development goals and implementation of the Paris Agreement requires technologies that utilize a wide range of minerals in vast quantities. Metal recycling and technological change will contribute to sustaining supply, but mining must continue and grow for the foreseeable future to ensure that such minerals remain available to industry. New links are needed between existing institutional frameworks to oversee responsible sourcing of minerals, trajectories for mineral exploration, environmental practices, and consumer awareness of the effects of consumption. Here we present, through analysis of a comprehensive set of data and demand forecasts, an interdisciplinary perspective on how best to ensure ecologically viable continuity of global mineral supply over the coming decades.

Recycling the liquid fraction of alkaline hydrogen peroxide in the pretreatment of corn stover.

PubMed

Alencar, Bárbara Ribeiro Alves; Reis, Alexandre Libanio Silva; de Souza, Raquel de Fatima Rodrigues; Morais, Marcos Antônio; Menezes, Rômulo Simões Cezar; Dutra, Emmanuel Damilano

2017-10-01

The aim of this study was to evaluate the influence of recycling the liquid fraction of pretreatment with alkaline hydrogen peroxide (AHP) on the hydrolysis of corn stover. Corn stover was pretreated in the traditional condition with 7.5% v/v H 2 O 2 . After pretreatment, the solids were separated from the liquid fraction and five successive reuse cycles of the liquid fraction were tested. The solid fraction from pretreatment in each recycle was submitted to enzymatic hydrolysis. The number of recycles had a linear negative effect (R 2 =0.98) on biomass delignification efficiency and also affected negatively the enzymatic conversion efficiency. Despite the decrease in efficiency after each recycling step, reuse of the liquid fraction leads to reduction in water, H 2 O 2 and NaOH consumption of up to 57.6%, 59.6% and 57.6%, respectively. These findings point to an efficient recycling technology, which may reduce costs and save water. Copyright © 2017 Elsevier Ltd. All rights reserved.

Recycling potential of neodymium: the case of computer hard disk drives.

PubMed

Sprecher, Benjamin; Kleijn, Rene; Kramer, Gert Jan

2014-08-19

Neodymium, one of the more critically scarce rare earth metals, is often used in sustainable technologies. In this study, we investigate the potential contribution of neodymium recycling to reducing scarcity in supply, with a case study on computer hard disk drives (HDDs). We first review the literature on neodymium production and recycling potential. From this review, we find that recycling of computer HDDs is currently the most feasible pathway toward large-scale recycling of neodymium, even though HDDs do not represent the largest application of neodymium. We then use a combination of dynamic modeling and empirical experiments to conclude that within the application of NdFeB magnets for HDDs, the potential for loop-closing is significant: up to 57% in 2017. However, compared to the total NdFeB production capacity, the recovery potential from HDDs is relatively small (in the 1-3% range). The distributed nature of neodymium poses a significant challenge for recycling of neodymium.

Combining physico-chemical analysis with a Daphnia magna bioassay to evaluate a recycling technology for drinking water treatment plant waste residuals.

PubMed

Chen, Ting; Xu, Yongpeng; Zhu, Shijun; Cui, Fuyi

2015-12-01

Recycling water treatment plant (WTP) waste residuals is considered to be a feasible method to enhance the efficiency of pollutant removal. This study also evaluated the safety and water quality of a pilot-DWTP waste residuals recycling technology by combining physical-chemistry analysis with a Daphnia magna assay. The water samples taken from each treatment step were extracted and concentrated by XAD-2 resin and were then analyzed for immobilization and enzyme activity with D. magna. The measured parameters, such as the dissolve organic carbon (DOC), UV254 and THM formation potential (THMFPs) of the recycling process, did not obviously increase over 15 days of continuous operation and were even lower than typical values from a conventional process. The extract concentration ranged from 0 to 2 Leq/ml as measured on the 7th and 15th days and the immobilization of D. magna exposed to water treated by the recycling process was nearly equivalent to that of the conventional process. Both the superoxide dismutase (SOD) and the catalase (CAT) activity assay indicated that a lower dose of water extract (0.5, 1, 1.5 Leq/ml) could stimulate the enzyme activity of D. magna, whereas a higher dose (2 Leq/ml at the sampling point C3, R3, R4 ) inhibits the activity. Moreover, the SOD and CAT activity of D. magna with DOC and UV254 showed a strong concentration-effect relationship, where the concentration range of DOC and UV254 were 4.1-16.2 mg/L and 0.071-4.382 cm(-1), respectively. The results showed that there was no statistically significant difference (p>0.05) between the conventional and recycling treatment processes and the toxicity of water samples in the recycling process did not increase during the 15-day continuous recycling trial. Copyright © 2015 Elsevier Inc. All rights reserved.

The water treatment and recycling in 105-day bioregenerative life support experiment in the Lunar Palace 1

NASA Astrophysics Data System (ADS)

Xie, Beizhen; Zhu, Guorong; Liu, Bojie; Su, Qiang; Deng, Shengda; Yang, Lige; Liu, Guanghui; Dong, Chen; Wang, Minjuan; Liu, Hong

2017-11-01

In the bioregenerative life support system (BLSS), water recycling is one of the essential issues. The Lunar Palace 1, a ground-based bioregenerative life support system experimental facility, has been developed by our team and a 105-day closed bioregenerative life support experiment with multi-crew involved has been accomplished within this large-scale facility. During the 105-day experiment, activated carbon-absorption/ultra-filtration, membrane-biological activated carbon reactor and reduced pressure distillation technology have been used to purify the condensate water, sanitary & kitchen wastewater and urine, respectively. The results demonstrated that the combination of those technologies can achieve 100% regeneration of the water inside the Lunar Palace 1. The purified condensate water (the clean water) could meet the standards for drinking water quality in China (GB5749-2006). The treatment capacity of the membrane-biological activated carbon reactor for sanitary & kitchen wastewater could reach 150 kg/d. During the 105-d experiment, the average volume loading of the bioreactor was 0.441 kgCOD/(m3d), and the average COD removal efficiency was about 85.3%. The quality of the purified sanitary & kitchen wastewater (the greywater) could meet the standards for irrigation water quality (GB 5084-2005). In addition, during the 105-day experiment, the total excreted urine volume of three crew members was 346 L and the contained water was totally treated and recovered. The removal efficiency of ion from urine was about 88.12%. Moreover, partial nitrogen within the urine was recovered as well and the average recovery ratio was about 20.5%. The study laid a foundation for the water recycling technologies which could be used in BLSS for lunar or Mars bases.

Technology advancement: a factor in increasing resource use

USGS Publications Warehouse

Wilburn, David R.; Goonan, Thomas G.; Bleiwas, Donald I.

2001-01-01

The specter of mineral resource scarcity has been repeatedly raised as a concern because ever-growing populations with seemingly insatiable appetites for minerals place claims against a finite resource endowment. This report analyzes how technology has helped to ease resource constraints, and uses case studies of aluminum, copper, potash, and sulfur minerals to identify the effects of technology on resource supply. In spite of heightened demand for and increased loss of resources to environmental policy and urbanization, mineral producers historically have been able to continually expand production and lower costs. Specific production increases for the years 1900-98 were: aluminum (3,250 percent), copper (2,465 percent), potash (3,770 percent), and sulfur (6,000 percent). For the same period, constant-dollar (1998) prices decreased: aluminum (90 percent), copper (75 percent), potash (94 percent), and sulfur (89 percent). The application of technology has made available mineral deposits that were previously overlooked or considered non-viable. Using technology, producers can meet the demand for stronger, energy-efficient, more environmentally safe products with less physical material. Technologies have been developed to increase the amount of materials recycled and remanufactured. Technology development can occur in breakthroughs, but most often advances incrementally. Technological development is driven by the profit motive.

A path to integration in an academic health science center.

PubMed Central

Panko, W. B.; Wilson, W.

1992-01-01

This article describes a networking and integration strategy in use at the University of Michigan Medical Center. This strategy builds upon the existing technology base and is designed to provide a roadmap that will direct short-term development along a productive, long-term path. It offers a way to permit the short-term development of incremental solutions to current problems while at the same time maximizing the likelihood that these incremental efforts can be recycled into a more comprehensive approach. PMID:1336413

Ensuring sustainability of non-networked sanitation technologies: an approach to standardization.

PubMed

Starkl, Markus; Brunner, Norbert; Feil, Magdalena; Hauser, Andreas

2015-06-02

Non-networked sanitation technologies use no sewer, water or electricity lines. Based on a review of 45 commercially distributed technologies, 12 (representing three concepts) were selected for a detailed audit. They were located in six countries of Africa and Asia. The safety of users was generally assured and the costs per use were not excessive, whereas costs were fully transparent for only one technology surveyed. A main drawback was insufficient quality of the byproducts from on-site treatment, making recycling in agriculture a hygienic and environmental risk. Further, no technology was sufficiently mature (requiring e.g. to shift wastes by hand). In order to promote further development and give producers of mature products a competitive advantage, the paper proposes a certification of technologies to confirm the fulfillment of basic requirements to make them attractive for future users.

A kinetic study of struvite precipitation recycling technology with NaOH/Mg(OH)2 addition.

PubMed

Yu, Rongtai; Ren, Hongqiang; Wang, Yanru; Ding, Lili; Geng, Jingji; Xu, Ke; Zhang, Yan

2013-09-01

Struvite precipitation recycling technology is received wide attention in removal ammonium and phosphate out of wastewater. While past study focused on process efficiency, and less on kinetics. The kinetic study is essential for the design and optimization in the application of struvite precipitation recycling technology. The kinetics of struvite with NaOH/Mg(OH)2 addition were studied by thermogravimetry analysis with three rates (5, 10, 20 °C/min), using Friedman method and Ozawa-Flynn-Wall method, respectively. Degradation process of struvite with NaOH/Mg(OH)2 addition was three steps. The stripping of ammonia from struvite was mainly occurred at the first step. In the first step, the activation energy was about 70 kJ/mol, which has gradually declined as the reaction progress. By model fitting studies, the proper mechanism function for struvite decomposition process with NaOH/Mg(OH)2 addition was revealed. The mechanism function was f(α)=α(α)-(1-α)(n), a Prout-Tompkins nth order (Bna) model. Copyright © 2013 Elsevier Ltd. All rights reserved.

Thorium Fuel Options for Sustained Transuranic Burning in Pressurized Water Reactors - 12381

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rahman, Fariz Abdul; Lee, John C.; Franceschini, Fausto

2012-07-01

As described in companion papers, Westinghouse is proposing the adoption of a thorium-based fuel cycle to burn the transuranics (TRU) contained in the current Used Nuclear Fuel (UNF) and transition towards a less radio-toxic high level waste. A combination of both light water reactors (LWR) and fast reactors (FR) is envisaged for the task, with the emphasis initially posed on their TRU burning capability and eventually to their self-sufficiency. Given the many technical challenges and development times related to the deployment of TRU burners fast reactors, an interim solution making best use of the current resources to initiate burning themore » legacy TRU inventory while developing and testing some technologies of later use is desirable. In this perspective, a portion of the LWR fleet can be used to start burning the legacy TRUs using Th-based fuels compatible with the current plants and operational features. This analysis focuses on a typical 4-loop PWR, with 17x17 fuel assembly design and TRUs (or Pu) admixed with Th (similar to U-MOX fuel, but with Th instead of U). Global calculations of the core were represented with unit assembly simulations using the Linear Reactivity Model (LRM). Several assembly configurations have been developed to offer two options that can be attractive during the TRU transmutation campaign: maximization of the TRU transmutation rate and capability for TRU multi-recycling, to extend the option of TRU recycling in LWR until the FR is available. Homogeneous as well as heterogeneous assembly configurations have been developed with various recycling schemes (Pu recycle, TRU recycle, TRU and in-bred U recycle etc.). Oxide as well as nitride fuels have been examined. This enabled an assessment of the potential for burning and multi-recycling TRU in a Th-based fuel PWR to compare against other more typical alternatives (U-MOX and variations thereof). Results will be shown indicating that Th-based PWR fuel is a promising option to multi-recycle and burn TRU in a thermal spectrum, while satisfying top-level operational and safety constraints. Various assembly designs have been proposed to assess the TRU burning potential of Th-based fuel in PWRs. In addition to typical homogeneous loading patterns, heterogeneous configurations exploiting the breeding potential of thorium to enable multiple cycles of TRU irradiation and burning have been devised. The homogeneous assembly design, with all pins featuring TRU in Th, has the benefit of a simple loading pattern and the highest rate of TRU transmutation, but it can be used only for a few cycles due to the rapid rise in the TRU content of the recycled fuel, which challenges reactivity control, safety coefficients and fuel handling. Due to its simple loading pattern, such assembly design can be used as the first step of Th implementation, achieving up to 3 times larger TRU transmutation rate than conventional U-MOX, assuming same fraction of MOX assemblies in the core. As the next step in thorium implementation, heterogeneous assemblies featuring a mixed array of Th-U and Th-U-TRU pins, where the U is in-bred from Th, have been proposed. These designs have the potential to enable burning an external supply of TRU through multiple cycles of irradiation, recovery (via reprocessing) and recycling of the residual actinides at the end of each irradiation cycle. This is achieved thanks to a larger breeding of U from Th in the heterogeneous assemblies, which reduces the TRU supply and thus mitigates the increase in the TRU core inventory for the multi-recycled fuel. While on an individual cycle basis the amount of TRU burned in the heterogeneous assembly is reduced with respect to the homogeneous design, TRU burning rates higher than single-pass U-MOX fuel can still be achieved, with the additional benefits of a multi-cycle transmutation campaign recycling all TRU isotopes. Nitride fuel, due its higher density and U breeding potential, together with its better thermal properties, ideally suits the objectives and constraints of the heterogeneous assemblies. However, significant technological advancements must be made before nitride fuels can be employed in an LWR: its water resistance needs to be improved and a viable technology to enrich N in N-15 must be devised. Moreover, for the nitride heterogeneous configurations examined in this study, the enhancement in TRU burning performance is achieved not only by replacing oxide with nitride fuel, but also by increasing the fuel rod size. This latter modification, allowed by the high thermal conductivity of nitride fuel, leads however to a very tight lattice, which may challenge reactor coolant pumps and assembly hold-down mechanisms, the former through an increase in core pressure drop and the latter through an increase in assembly lift-off forces. To alleviate these issues, while still achieving the large fuel-to-moderator ratios resulting from using tight lattices, wire wraps could be used in place of grid spacers. For tight lattices, typical grid spacers are hard to manufacture and their replacement with wire wraps is known to allow for a pressure drop reduction by at least 2 times. The studies, while certainly very preliminary, provide a starting point to devise an optimum strategy for TRU transmutation in Th-based PWR fuel. The viability of the scheme proposed depends on the timely phasing in of the associated technologies, with proper lead time and to solve the many challenges. These challenges are certainly substantial, and make the current once-through U-based scheme pursued in the US by far a more practical (and cheaper) option. However, when compared to other transmutation schemes, the proposed one has arguably similar challenges and unknowns with potentially bigger rewards. (authors)« less

Engineering sustainable development

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prendergast, J.

1993-10-01

This article discusses sustainable development, a policy which attempts to balance environmental preservation and economic growth, and promises a way to provide a decent life for Earth's human inhabitants without destroying the global ecosystem. Sustainable development is an effort to use technology to help clean up the mess it helped make, and engineers will be central players in its success or failure. Key aspects include more efficient energy use through conservation measures and switching to renewable sources, waste minimization, much greater recycling and reuse of materials, more comprehensive economic/environmental assessments employing life-cycle analyses, and better management of resources.

Critical Metals in Strategic Low-carbon Energy Technologies

NASA Astrophysics Data System (ADS)

Moss, R. L.

2012-04-01

Due to the rapid growth in demand for certain materials, compounded by political risks associated with the geographical concentration of the supply of them, shortages of materials could be a potential bottleneck to the deployment of low-carbon energy technologies. Consequently, an assessment has been carried out to ascertain whether such shortages could jeopardise the objectives of the EU's Strategic Energy Technology Plan (SET-Plan), especially in the six low-carbon energy technologies of SET-Plan, namely: nuclear, solar, wind, bioenergy, carbon capture and storage (CCS) and electricity grids. The assessment identified 14 metals for which the deployment of the six technologies will require 1% or more (and in some cases, much more) of current world supply per annum between 2020 and 2030. Following a more critical examination, based on the likelihood of rapid future global demand growth, limitations to expanding supply in the short to medium term, and the concentration of supply and political risks associated with key suppliers, 5 of the 14 metals were pinpointed to be at high risk, namely: the rare earth metals neodymium and dysprosium (for wind technology), and the by-products (from the processing of other metals) indium, tellurium and gallium (for photovoltaic technologies). In addition, the work has explored potential mitigation strategies, ranging from expanding European output, increasing recycling and reuse to reducing waste and finding substitutes for these metals in their main applications. Furthermore, recommendations are provided which include closely working with the EU's Raw Materials Initiative; supporting efforts to ensure reliable supply of ore concentrates at competitive prices; promoting R&D and demonstration projects on new lower cost separation processes; and promoting the further development of recycling technologies and increasing end-of-life collection

PCR Based Microbial Monitor for Analysis of Recycled Water Aboard the ISSA: Issues and Prospects

NASA Technical Reports Server (NTRS)

Cassell, Gail H.; Lefkowitz, Elliot J.; Glass, John I.

1995-01-01

The monitoring of spacecraft life support systems for the presence of health threatening microorganisms is paramount for crew well being and successful completion of missions. Development of technology to monitor spacecraft recycled water based on detection and identification of the genetic material of contaminating microorganisms and viruses would be a substantial improvement over current NASA plans to monitor recycled water samples that call for the use of conventional microbiology techniques which are slow, insensitive, and labor intensive. The union of the molecular biology techniques of DNA probe hybridization and polymerase chain reaction (PCR) offers a powerful method for the detection, identification, and quantification of microorganisms and viruses. This technology is theoretically capable of assaying samples in as little as two hours with specificity and sensitivity unmatched by any other method. A major advance in probe-hybridization/PCR has come about in a technology called TaqMan(TM), which was invented by Perkin Elmer. Instrumentation using TaqMan concepts is evolving towards devices that could meet NASA's needs of size, low power use, and simplicity of operation. The chemistry and molecular biology needed to utilize these probe-hybridization/PCR instruments must evolve in parallel with the hardware. The following issues of chemistry and biology must be addressed in developing a monitor: Early in the development of a PCR-based microbial monitor it will be necessary to decide how many and which organisms does the system need the capacity to detect. We propose a set of 17 different tests that would detect groups of bacteria and fungus, as well as specific eukaryotic parasites and viruses; In order to use the great sensitivity of PCR it will be necessary to concentrate water samples using filtration. If a lower limit of detection of 1 microorganism per 100 ml is required then the microbes in a 100 ml sample must be concentrated into a volume that can be added to a PCR assay; There are not likely to be contaminants in ISSA recycled water that would inhibit PCR resulting in false-negative results; The TaqMan PCR product detection system is the most promising method for developing a rapid, highly automated gene-based microbial monitoring system. The method is inherently quantitative. NASA and other government agencies have invested in other technologies that, although potentially could lead to revolutionary advances, are not likely to mature in the next 5 years into working systems; PCR-based methods cannot distinguish between DNA or RNA of a viable microorganism and that of a non-viable organism. This may or may not be an important issue with reclaimed water on the ISSA. The recycling system probably damages the capacity of the genetic material of any bacteria or viruses killed during processing to serve as a template in a PCR desinged to amplify a large segment of DNA (less than 650 base pairs). If necessary, vital dye staining could be used in addition to PCR, to enumerate the viable cells in a water sample; The quality control methods have been developed to insure that PCR's are working properly, and that reactions are not contaminated with PCR carryover products which could lead to the generation of false-positive results; and The sequences of the small rRNA subunit gene for a large number of microorganisms are known, and they consititue the best database for rational development of the oligonucleotide reagents that give PCR its great specificity. From those gene sequences, sets of oligonucleotide primers for PCR and Taqman detection that could be used in a NASA microbial monitor were constructed using computer based methods. In addition to space utilization, a microbial monitior will have tremendous terrestrial applications. Analysis of patient samples for microbial pathogens, testing industrial effluent for biofouling bacteria, and detection biological warfare agents on the battlefield are but a few of the diverse potential uses for this technology. Once fully developed, gene-based microbial monitors will become the fundamental tool in every lab that tests for microbial contaminants, and serve as a powerful weapon in mankind's war with the germ world.

Wee Recyclers. An Activity Guide for Ages 3-5.

ERIC Educational Resources Information Center

Wisconsin State Dept. of Natural Resources, Madison.

Recycling and reusing are skills that can be developed in early child care programs. This activity guide is intended to help teach children (ages 3-5) about recycling using simple, hands-on activities. Teacher-directed activities involve setting up a recycling center, sorting recyclable items, landfills, litter, a recycling alphabet, and ways that…

Overview of reductants utilized in nuclear fuel reprocessing/recycling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Paviet-Hartmann, P.; Riddle, C.; Campbell, K.

2013-07-01

The most widely used reductant to partition plutonium from uranium in the Purex process was ferrous sulfamate, other alternates were proposed such as hydrazine-stabilized ferrous nitrate or uranous nitrate, platinum catalyzed hydrogen, and hydrazine, hydroxylamine salts. New candidates to replace hydrazine or hydroxylamine nitrate (HAN) are pursued worldwide. They may improve the performance of the industrial Purex process towards different operations such as de-extraction of plutonium and reduction of the amount of hydrazine which will limit the formation of hydrazoic acid. When looking at future recycling technologies using hydroxamic ligands, neither acetohydroxamic acid (AHA) nor formohydroxamic acid (FHA) seem promisingmore » because they hydrolyze to give hydroxylamine and the parent carboxylic acid. Hydroxyethylhydrazine, HOC{sub 2}H{sub 4}N{sub 2}H{sub 3} (HEH) is a promising non-salt-forming reductant of Np and Pu ions because it is selective to neptunium and plutonium ions at room temperature and at relatively low acidity, it could serve as a replacement of HAN or AHA for the development of a novel used nuclear fuel recycling process.« less

E-waste interventions in Ghana.

PubMed

Asante, Kwadwo Ansong; Pwamang, John A; Amoyaw-Osei, Yaw; Ampofo, Joseph Addo

2016-03-01

Electrical and electronic waste (e-waste) has become an emerging environmental and human health problem in the world in the 21st century. Recently, the developing nations of West Africa (e.g. Ghana and Nigeria) have become a major destination for e-waste worldwide. In Ghana, the e-waste recyclers use primitive methods (mechanical shredding and open burning) to remove plastic insulation from copper cables. This technique can release highly toxic chemicals and severely affect the environment and human health if improperly managed. It is as a result of the adverse impact on human health that some interventions are being made in Ghana to reduce exposure. The present mode of recycling/dismantling, which happens at Agbogbloshie must be replaced by official receiving/recycling centers to be established. Currently, equipment to strip both large and small cables are available in the country via the Blacksmith Institute (USA) and it is expected that the e-waste workers will embrace the use of these machines. This technology will go a long way to help prevent the burning of e-waste and will be replicated in other smaller e-waste centers in the country.

Cryogenic hydrogen-induced air-liquefaction technologies for combined-cycle propulsion applications

NASA Technical Reports Server (NTRS)

Escher, William J. D.

1992-01-01

Given here is a technical assessment of the realization of cryogenic hydrogen induced air liquefaction technologies in a prospective onboard aerospace vehicle process setting. The technical findings related to the status of air liquefaction technologies are reviewed. Compact lightweight cryogenic heat exchangers, heat exchanger atmospheric constituent fouling alleviation measures, para/ortho-hydrogen shift-conversion catalysts, cryogenic air compressors and liquid air pumps, hydrogen recycling using slush hydrogen as a heat sink, liquid hydrogen/liquid air rocket-type combustion devices, and technically related engine concepts are discussed. Much of the LACE work is related to aerospaceplane propulsion concepts that were developed in the 1960's. Emphasis is placed on the Liquid Air Cycle Engine (LACE).

A novel method of utilizing permeable reactive kiddle (PRK) for the remediation of acid mine drainage.

PubMed

Lee, Woo-Chun; Lee, Sang-Woo; Yun, Seong-Taek; Lee, Pyeong-Koo; Hwang, Yu Sik; Kim, Soon-Oh

2016-01-15

Numerous technologies have been developed and applied to remediate AMD, but each has specific drawbacks. To overcome the limitations of existing methods and improve their effectiveness, we propose a novel method utilizing permeable reactive kiddle (PRK). This manuscript explores the performance of the PRK method. In line with the concept of green technology, the PRK method recycles industrial waste, such as steel slag and waste cast iron. Our results demonstrate that the PRK method can be applied to remediate AMD under optimal operational conditions. Especially, this method allows for simple installation and cheap expenditure, compared with established technologies. Copyright © 2015 Elsevier B.V. All rights reserved.

A nickel metal hydride battery for electric vehicles

NASA Astrophysics Data System (ADS)

Ovshinsky, S. R.; Fetcenko, M. A.; Ross, J.

1993-04-01

An efficient battery is the key technological element to the development of practical electric vehicles. The science and technology of a nickel metal hydride battery, which stores hydrogen in the solid hydride phase and has high energy density, high power, long life, tolerance to abuse, a wide range of operating temperature, quick-charge capability, and totally sealed maintenance-free operation, is described. A broad range of multi-element metal hydride materials that use structural and compositional disorder on several scales of length has been engineered for use as the negative electrode in this battery. The battery operates at ambient temperature, is made of nontoxic materials, and is recyclable. Demonstration of the manufacturing technology has been achieved.

Design and optimization of photovoltaics recycling infrastructure.

PubMed

Choi, Jun-Ki; Fthenakis, Vasilis

2010-11-15

With the growing production and installation of photovoltaics (PV) around the world constrained by the limited availability of resources, end-of-life management of PV is becoming very important. A few major PV manufacturers currently are operating several PV recycling technologies at the process level. The management of the total recycling infrastructure, including reverse-logistics planning, is being started in Europe. In this paper, we overview the current status of photovoltaics recycling planning and discuss our mathematic modeling of the economic feasibility and the environmental viability of several PV recycling infrastructure scenarios in Germany; our findings suggest the optimum locations of the anticipated PV take-back centers. Short-term 5-10 year planning for PV manufacturing scraps is the focus of this article. Although we discuss the German situation, we expect the generic model will be applicable to any region, such as the whole of Europe and the United States.

Recycling Expensive Medication: Why Not?

PubMed Central

Pomerantz, Jay M

2004-01-01

New (and proposed) advances in packaging, preserving, labeling, and verifying product integrity of individual tablets and capsules may allow for the recycling of certain expensive medicines. Previously sold, but unused, medication, if brought back to special pharmacies for resale or donation, may provide a low-cost source of patent-protected medicines. Benefits of such a program go beyond simply providing affordable medication to the poor. This article suggests that medicine recycling may be a possibility (especially if manufacturers are mandated to blister-package and bar-code individual tablets and capsules). This early discussion of medication recycling identifies relevant issues, such as: need, rationale, existing programs, available supplies, expiration dates, new technology for ensuring safety and potency, environmental impact, public health benefits, program focus, program structure, and liability. PMID:15266231

Tire Recycling

NASA Technical Reports Server (NTRS)

1997-01-01

Cryopolymers, Inc. tapped NASA expertise to improve a process for recycling vehicle tires by converting shredded rubber into products that can be used in asphalt road beds, new tires, hoses, and other products. In conjunction with the Southern Technology Applications Center and Stennis Space Center, NASA expertise in cryogenic fuel-handling needed for launch vehicle and spacecraft operations was called upon to improve the recycling concept. Stennis advised Cryopolymers on the type of equipment required, as well as steps to reduce the amount of liquid nitrogen used in the process. They also guided the company to use more efficient ways to control system hardware. It is estimated that more than 300 million tires nationwide are produced per year. Cryopolymers expects to reach a production rate of 5,000 tires recycled per day.

What do we know about metal recycling rates?

USGS Publications Warehouse

Graedel, T.E.; Allwood, J.; Birat, J.-P.; Buchert, M.; Hageluken, C.; Reck, B.K.; Sibley, S.F.; Sonnemann, G.

2011-01-01

The recycling of metals is widely viewed as a fruitful sustainability strategy, but little information is available on the degree to which recycling is actually taking place. This article provides an overview on the current knowledge of recycling rates for 60 metals. We propose various recycling metrics, discuss relevant aspects of recycling processes, and present current estimates on global end-of-life recycling rates (EOL-RR; i.e., the percentage of a metal in discards that is actually recycled), recycled content (RC), and old scrap ratios (OSRs; i.e., the share of old scrap in the total scrap flow). Because of increases in metal use over time and long metal in-use lifetimes, many RC values are low and will remain so for the foreseeable future. Because of relatively low efficiencies in the collection and processing of most discarded products, inherent limitations in recycling processes, and the fact that primary material is often relatively abundant and low-cost (which thereby keeps down the price of scrap), many EOL-RRs are very low: Only for 18 metals (silver, aluminum, gold, cobalt, chromium, copper, iron, manganese, niobium, nickel, lead, palladium, platinum, rhenium, rhodium, tin, titanium, and zinc) is the EOL-RR above 50% at present. Only for niobium, lead, and ruthenium is the RC above 50%, although 16 metals are in the 25% to 50% range. Thirteen metals have an OSR greater than 50%. These estimates may be used in considerations of whether recycling efficiencies can be improved; which metric could best encourage improved effectiveness in recycling; and an improved understanding of the dependence of recycling on economics, technology, and other factors. ?? 2011 by Yale University.

Assessing recycling versus incineration of key materials in municipal waste: The importance of efficient energy recovery and transport distances

DOE Office of Scientific and Technical Information (OSTI.GOV)

Merrild, Hanna; Larsen, Anna W., E-mail: awla@env.dtu.dk; Christensen, Thomas H.

Highlights: Black-Right-Pointing-Pointer We model the environmental impact of recycling and incineration of household waste. Black-Right-Pointing-Pointer Recycling of paper, glass, steel and aluminium is better than incineration. Black-Right-Pointing-Pointer Recycling and incineration of cardboard and plastic can be equally good alternatives. Black-Right-Pointing-Pointer Recyclables can be transported long distances and still have environmental benefits. Black-Right-Pointing-Pointer Paper has a higher environmental benefit than recyclables found in smaller amounts. - Abstract: Recycling of materials from municipal solid waste is commonly considered to be superior to any other waste treatment alternative. For the material fractions with a significant energy content this might not be the casemore » if the treatment alternative is a waste-to-energy plant with high energy recovery rates. The environmental impacts from recycling and from incineration of six material fractions in household waste have been compared through life cycle assessment assuming high-performance technologies for material recycling as well as for waste incineration. The results showed that there are environmental benefits when recycling paper, glass, steel and aluminium instead of incinerating it. For cardboard and plastic the results were more unclear, depending on the level of energy recovery at the incineration plant, the system boundaries chosen and which impact category was in focus. Further, the environmental impact potentials from collection, pre-treatment and transport was compared to the environmental benefit from recycling and this showed that with the right means of transport, recyclables can in most cases be transported long distances. However, the results also showed that recycling of some of the material fractions can only contribute marginally in improving the overall waste management system taking into consideration their limited content in average Danish household waste.« less

Waste biorefineries: Enabling circular economies in developing countries.

PubMed

Nizami, A S; Rehan, M; Waqas, M; Naqvi, M; Ouda, O K M; Shahzad, K; Miandad, R; Khan, M Z; Syamsiro, M; Ismail, I M I; Pant, Deepak

2017-10-01

This paper aims to examine the potential of waste biorefineries in developing countries as a solution to current waste disposal problems and as facilities to produce fuels, power, heat, and value-added products. The waste in developing countries represents a significant source of biomass, recycled materials, chemicals, energy, and revenue if wisely managed and used as a potential feedstock in various biorefinery technologies such as fermentation, anaerobic digestion (AD), pyrolysis, incineration, and gasification. However, the selection or integration of biorefinery technologies in any developing country should be based on its waste characterization. Waste biorefineries if developed in developing countries could provide energy generation, land savings, new businesses and consequent job creation, savings of landfills costs, GHG emissions reduction, and savings of natural resources of land, soil, and groundwater. The challenges in route to successful implementation of biorefinery concept in the developing countries are also presented using life cycle assessment (LCA) studies. Copyright © 2017 Elsevier Ltd. All rights reserved.

An Evaluation of Vegetated Roofing Technology: Application at Air Force Plant Four, Building 15

DTIC Science & Technology

2004-03-01

layer of mineral wool , or recycled foam, or even installing a membrane that has water-absorbing crystals built-in. Adding more water retention...Sarnafil membrane has inherent root protection. Insulation: Eight cm thick hydroscopic mineral wool located under the waterproofing membrane...Drainage: Xero Drain, developed by Xeroflor. Growing medium: Four cm of mineral wool . This is a very lightweight material with excellent water

JPRS Report, Science & Technology, Europe

DTIC Science & Technology

1992-10-27

reprocessors involved. PRAVDA The BMW, Ford, Mercedes - Benz , Opel, Porsche and VW companies have joined together in the Project Team Recycling of Old...WEHRTECHNIK, Jun 92] 27 Effect of Common Market on European Aerospace Industry [Fausto Cereti; Bonn WEHRTECHNIK, Jun 92] 29 Thyssen Develops Laser...Europe. What, in your opinion, do you think the final solution will be in this sector of the industry? [Mehdorn] We’re talking about four market

Recycling and social technologies for sustainability: The Brazilian experience of wastepickers' inclusion in selective collection programs.

PubMed

Lima, Francisco de Paula Antunes; de Oliveira, Fabiana Goulart

2017-01-01

Alternatives are being developed for waste treatment all over the world. Solidary selective collection is a recognized social technology for taking millions of people out of absolute poverty. However, this technology raises crucial questions regarding its nature and development perspective. What can be said of the legitimacy of a social technology that is born from misery and maintains wastepickers in precarious work conditions? This article approaches issues based on the analysis of the wastepickers' work process, highlighting the difficulties and interpersonal conflicts, the strong social bonds and creativity that reveal the potential of efficiency and solidarity of this social technology. The analyses are founded on empirical descriptions of work situations and organizational arrangements that the wastepickers themselves have developed. The observations were made during the work, followed by interviews focused on significant events and behaviors. The contradiction between efficiency and solidarity, which excludes workers from the formal labor market, finds in the associations a solution for people with different capacities. This social technology offers much more than simple survival or exoticism. The wastepickers create a sustainable mode of production, putting together economic, social and environmental criteria in an innovative and fair production technology.

Response to waste electrical and electronic equipments in China: legislation, recycling system, and advanced integrated process.

PubMed

Zhou, Lei; Xu, Zhenming

2012-05-01

Over the past 30 years, China has been suffering from negative environmental impacts from distempered waste electrical and electronic equipments (WEEE) recycling activities. For the purpose of environmental protection and resource reusing, China made a great effort to improve WEEE recycling. This article reviews progresses of three major fields in the development of China's WEEE recycling industry: legal system, formal recycling system, and advanced integrated process. Related laws concerning electronic waste (e-waste) management and renewable resource recycling are analyzed from aspects of improvements and loopholes. The outcomes and challenges for existing formal recycling systems are also discussed. The advantage and deficiency related to advanced integrated recycling processes for typical e-wastes are evaluated respectively. Finally, in order to achieve high disposal rates of WEEE, high-quantify separation of different materials in WEEE and high added value final products produced by separated materials from WEEE, an idea of integrated WEEE recycling system is proposed to point future development of WEEE recycling industry. © 2012 American Chemical Society

Mission Benefits Analysis of Logistics Reduction Technologies

NASA Technical Reports Server (NTRS)

Ewert, Michael K.; Broyan, James Lee, Jr.

2013-01-01

Future space exploration missions will need to use less logistical supplies if humans are to live for longer periods away from our home planet. Anything that can be done to reduce initial mass and volume of supplies or reuse or recycle items that have been launched will be very valuable. Reuse and recycling also reduce the trash burden and associated nuisances, such as smell, but require good systems engineering and operations integration to reap the greatest benefits. A systems analysis was conducted to quantify the mass and volume savings of four different technologies currently under development by NASA s Advanced Exploration Systems (AES) Logistics Reduction and Repurposing project. Advanced clothing systems lead to savings by direct mass reduction and increased wear duration. Reuse of logistical items, such as packaging, for a second purpose allows fewer items to be launched. A device known as a heat melt compactor drastically reduces the volume of trash, recovers water and produces a stable tile that can be used instead of launching additional radiation protection. The fourth technology, called trash-to-gas, can benefit a mission by supplying fuel such as methane to the propulsion system. This systems engineering work will help improve logistics planning and overall mission architectures by determining the most effective use, and reuse, of all resources.

Back-end of the fuel cycle - Indian scenario

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wattal, P.K.

Nuclear power has a key role in meeting the energy demands of India. This can be sustained by ensuring robust technology for the back end of the fuel cycle. Considering the modest indigenous resources of U and a huge Th reserve, India has adopted a three stage Nuclear Power Programme (NPP) based on 'closed fuel cycle' approach. This option on 'Recovery and Recycle' serves twin objectives of ensuring adequate supply of nuclear fuel and also reducing the long term radio-toxicity of the wastes. Reprocessing of the spent fuel by Purex process is currently employed. High Level Liquid Waste (HLW) generatedmore » during reprocessing is vitrified and undergoes interim storage. Back-end technologies are constantly modified to address waste volume minimization and radio-toxicity reduction. Long-term management of HLW in Indian context would involve partitioning of long lived minor actinides and recovery of valuable fission products specifically cesium. Recovery of minor actinides from HLW and its recycle is highly desirable for the sustained growth of India's NPPs. In this context, programme for developing and deploying partitioning technologies on industrial scale is pursued. The partitioned elements could be either transmuted in Fast Reactors (FRs)/Accelerated Driven Systems (ADS) as an integral part of sustainable Indian NPP. (authors)« less

Mission Benefits Analysis of Logistics Reduction Technologies

NASA Technical Reports Server (NTRS)

Ewert, Michael K.; Broyan, James L.

2012-01-01

Future space exploration missions will need to use less logistical supplies if humans are to live for longer periods away from our home planet. Anything that can be done to reduce initial mass and volume of supplies or reuse or recycle items that have been launched will be very valuable. Reuse and recycling also reduce the trash burden and associated nuisances, such as smell, but require good systems engineering and operations integration to reap the greatest benefits. A systems analysis was conducted to quantify the mass and volume savings of four different technologies currently under development by NASA fs Advanced Exploration Systems (AES) Logistics Reduction and Repurposing project. Advanced clothing systems lead to savings by direct mass reduction and increased wear duration. Reuse of logistical items, such as packaging, for a second purpose allows fewer items to be launched. A device known as a heat melt compactor drastically reduces the volume of trash, recovers water and produces a stable tile that can be used instead of launching additional radiation protection. The fourth technology, called trash ]to ]supply ]gas, can benefit a mission by supplying fuel such as methane to the propulsion system. This systems engineering work will help improve logistics planning and overall mission architectures by determining the most effective use, and reuse, of all resources.

Acceptance Testing of the Vapor Phase Catalytic Ammonia Removal Engineering Development Unit

NASA Technical Reports Server (NTRS)

Flynn, Michael; Fisher, John; Kliss, Mark; Tleimat, Maher; Quinn, Gregory; Fort, James; Nalette, Tim; Baker, Gale

2005-01-01

This paper describes the results of acceptance testing of the Vapor Phase Catalytic Ammonia Removal (VPCAR) technology. The VPCAR technology is currently being developed by NASA as a Mars transit vehicle water recycling system. NASA has recently completed a grant to develop a next generation VPCAR system. This grant was peer reviewed and funded through the Advanced Life Support (ALS) National Research Announcement (NRA). The grant funded a contract with Water Reuse Technology Inc. to construct an engineering development unit. This contract concluded with the shipment of the final deliverable to NASA on 8/31/03. The objective of the acceptance testing was to characterize the performance of this new system. This paper presents the results of mass power, and volume measurements for the delivered system. In addition, product water purity analysis for a Mars transit mission and a planetary base wastewater ersatz are provided. Acoustic noise levels, interface specifications and system reliability results are also discussed. An assessment of the readiness of the technology for human testing and recommendations for future improvements are provided.

A Lunar Surface System Supportability Technology Development Roadmap

NASA Technical Reports Server (NTRS)

Oeftering, Richard C.; Struk, Peter M.; Taleghani, Barmac K.

2009-01-01

This paper discusses the establishment of a Supportability Technology Development Roadmap as a guide for developing capabilities intended to allow NASA's Constellation program to enable a supportable, sustainable and affordable exploration of the Moon and Mars. Presented is a discussion of "supportability", in terms of space facility maintenance, repair and related logistics and a comparison of how lunar outpost supportability differs from the International Space Station. Supportability lessons learned from NASA and Department of Defense experience and their impact on a future lunar outpost is discussed. A supportability concept for future missions to the Moon and Mars that involves a transition from a highly logistics dependent to a logistically independent operation is discussed. Lunar outpost supportability capability needs are summarized and a supportability technology development strategy is established. The resulting Lunar Surface Systems Supportability Strategy defines general criteria that will be used to select technologies that will enable future flight crews to act effectively to respond to problems and exploit opportunities in a environment of extreme resource scarcity and isolation. This strategy also introduces the concept of exploiting flight hardware as a supportability resource. The technology roadmap involves development of three mutually supporting technology categories, Diagnostics Test & Verification, Maintenance & Repair, and Scavenging & Recycling. The technology roadmap establishes two distinct technology types, "Embedded" and "Process" technologies, with different implementation and thus different criteria and development approaches. The supportability technology roadmap addresses the technology readiness level, and estimated development schedule for technology groups that includes down-selection decision gates that correlate with the lunar program milestones. The resulting supportability technology roadmap is intended to develop a set of technologies with widest possible capability and utility with a minimum impact on crew time and training and remain within the time and cost constraints of the Constellation program

A Lunar Surface System Supportability Technology Development Roadmap

NASA Technical Reports Server (NTRS)

Oeftering, Richard C.; Struk, Peter M.; Taleghani, barmac K.

2011-01-01

This paper discusses the establishment of a Supportability Technology Development Roadmap as a guide for developing capabilities intended to allow NASA s Constellation program to enable a supportable, sustainable and affordable exploration of the Moon and Mars. Presented is a discussion of supportability, in terms of space facility maintenance, repair and related logistics and a comparison of how lunar outpost supportability differs from the International Space Station. Supportability lessons learned from NASA and Department of Defense experience and their impact on a future lunar outpost is discussed. A supportability concept for future missions to the Moon and Mars that involves a transition from a highly logistics dependent to a logistically independent operation is discussed. Lunar outpost supportability capability needs are summarized and a supportability technology development strategy is established. The resulting Lunar Surface Systems Supportability Strategy defines general criteria that will be used to select technologies that will enable future flight crews to act effectively to respond to problems and exploit opportunities in an environment of extreme resource scarcity and isolation. This strategy also introduces the concept of exploiting flight hardware as a supportability resource. The technology roadmap involves development of three mutually supporting technology categories, Diagnostics Test and Verification, Maintenance and Repair, and Scavenging and Recycling. The technology roadmap establishes two distinct technology types, "Embedded" and "Process" technologies, with different implementation and thus different criteria and development approaches. The supportability technology roadmap addresses the technology readiness level, and estimated development schedule for technology groups that includes down-selection decision gates that correlate with the lunar program milestones. The resulting supportability technology roadmap is intended to develop a set of technologies with widest possible capability and utility with a minimum impact on crew time and training and remain within the time and cost constraints of the Constellation program.

Thermal Reduction of NOx with Recycled Plastics.

PubMed

Oluwoye, Ibukun; Dlugogorski, Bogdan Z; Gore, Jeff; Vyazovkin, Sergey; Boyron, Olivier; Altarawneh, Mohammednoor

2017-07-05

This study develops technology for mitigation of NO x formed in thermal processes using recycled plastics such as polyethylene (PE). Experiments involve sample characterization, and thermogravimetric decomposition of PE under controlled atmospheres, with NO x concentration relevant to industrial applications. TGA-Fourier transform infrared (FTIR) spectroscopy and NO x chemiluminescence serve to obtain the removal efficiency of NO x by fragments of pyrolyzing PE. Typical NO x removal efficiency amounts to 80%. We apply the isoconversional method to derive the kinetic parameters, and observe an increasing dependency of activation energy on the reaction progress. The activation energies of the process span 135 kJ/mol to 226 kJ/mol, and 188 kJ/mol to 268 kJ/mol, for neat and recycled PE, respectively, and the so-called compensation effect accounts for the natural logarithmic pre-exponential ln (A/min -1 ) factors of ca. 19-35 and 28-41, in the same order, depending on the PE conversion in the experimental interval of between 5 and 95%. The observed delay in thermal events of recycled PE reflects different types of PE in the plastic, as measurements of intrinsic viscosity indicate that, the recycled PE comprises longer linear chains. The present evaluation of isoconversional activation energies affords accurate kinetic modeling of both isothermal and nonisothermal decomposition of PE in NO x -doped atmosphere. Subsequent investigations will focus on the effect of mass transfer and the presence of oxygen, as reburning of NO x in large-scale combustors take place at higher temperatures than those included in the current study.

Radioactive Waste Management - It's Role in contributing and achieving Sustainability. R1.13 The French strategy of waste management: technical and political dimensions of sustainability

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bazile, F.

2007-07-01

The sustainability of an energy policy depends on the manner in which it satisfies environmental, economical and social requirements. Nuclear energy is not an exception. The objectives of the future nuclear systems, as defined in the Generation IV International Forum, tend to optimize the ability of nuclear energy to satisfy sustainable development goals. In this regard, they involve strong commitments concerning waste management policy : five designs in six are based on a closed fuel cycle, in order to minimize the volume and radiotoxicity of final waste, and to recycle the fissile materials to save natural resources. Since its beginnings,more » the French civil nuclear programme has considered a long-term perspective and has developed spent fuel reprocessing. The French current industrial technology has already permitted to recycle 96% of spent fuel materials, to save 30% of natural resources, to reduce by 5 the amount of waste and to reduce by 10 the waste radiotoxicity, all these benefits for less than 6% of the kWh total cost. This strategy has always been criticized by the nuclear opponents, precisely because they saw that it was a sustainable way, and didn't accept to consider nuclear energy as a sustainable source of power. Two arguments were put forward these criticisms. First, the cost of reprocessing versus once-through cycle and second, the risk of proliferation induced by U-Pu partitioning process. These arguments were also invoked in international debates, and they have also been pleaded by the anti-nukes during the National Debate on HLLLW, at the end of 2005, preceding the vote of a new law in 2006 by the French parliament. Fortunately they have not convinced public opinion in France nor political decision-makers. A majority of people with no regard to technical background understand that recycling and saving the natural resources are sustainable principles. And, from a technical point of view, the 6% over cost does not seem significant considering the economics of nuclear power. Lastly, the risk proliferation is more related to the front-end technologies than to the back-end ones. So, the 2006 French Law 'for a sustainable radioactive waste management' has reinforced the closed-cycle strategy and has paved the way for a long-term development of nuclear energy in the 21. century and beyond, towards the third and fourth generations of nuclear systems. It has defined an R and D programme including the continuation of partitioning-transmutation of minor actinides and their recycling in 4. generation fast reactors. In parallel, the French president has committed the French Atomic Energy Commission to implement a 4. generation prototype reactor by 2020, with international cooperation, to guarantee the permanence of technology progress. In this regard, the waste management strategy can't be built without taking into account the perspectives of development of nuclear energy. These perspectives must include the best available technologies and, in the other hand, an adaptation to the political evolutions of societies. (authors)« less

Alternative polymer separation technology by centrifugal force in a melted state.

PubMed

Dobrovszky, Károly; Ronkay, Ferenc

2014-11-01

In order to upgrade polymer waste during recycling, separation should take place at high purity. The present research was aimed to develop a novel, alternative separation opportunity, where the polymer fractions were separated by centrifugal force in melted state. The efficiency of the constructed separation equipment was verified by two immiscible plastics (polyethylene terephthalate, PET; low density polyethylene, LDPE), which have a high difference of density, and of which large quantities can also be found in the municipal solid waste. The results show that the developed equipment is suitable not only for separating dry blended mixtures of PET/LDPE into pure components again, but also for separating prefabricated polymer blends. By this process it becomes possible to recover pure polymer substances from multi-component products during the recycling process. The adequacy of results was verified by differential scanning calorimetry (DSC) measurement as well as optical microscopy and Raman spectroscopy. Copyright © 2014 Elsevier Ltd. All rights reserved.

Development of a prototype experiment for treating CELSS and PCELSS wastes to produce nutrients for plant growth

NASA Technical Reports Server (NTRS)

1983-01-01

Future long term spaceflights require extensive recycling of wastes to minimize the need for resupplying the vessel. The recycling occurs in a fully or partially closed environment life support system (CELSS or PCELSS). The National Aeronautics and Space Administration (NASA) is interested in converting wastewater into potable water or water for hydroponic farming as part of a CELSS. The development of technologies for wastewater treatment that produce a minimum of by-products is essential. One process that achieves good conversion of moderately concentrated organic wastes in water (1 to 20% by weight) completely to carbon dioxide and water is oxidation in supercritical water. Both air (or oxygen) and many organics are completely miscible with supercritical water, so there are no interphase mass transport resistances that limits the overall oxidation reaction. The temperature of supercritical water, which must be above 374 C, is also sufficient to have rapid reaction kinetics for the oxidations.

A flexible environmental reuse/recycle policy based on economic strength.

PubMed

Tsiliyannis, C A

2007-01-01

Environmental policies based on fixed recycling rates may lead to increased environmental impacts (e.g., landfilled wastes) during economic expansion. A rate policy is proposed, which is adjusted according to the overall strength or weakness of the economy, as reflected by overall packaging demand and consumption, production and imports-exports. During economic expansion featuring rising consumption, production or exports, the proposed flexible policy suggests a higher reuse/recycle rate. During economic slowdown a lower rate results in lower impacts. The flexible target rates are determined in terms of annual data, including consumption, imports-exports and production. Higher environmental gains can be achieved at lower cost if the flexible policy is applied to widely consumed packaging products and materials associated with low rates, or if cleaner recycling technology is adopted.

Life cycle assessment of electronic waste treatment.

PubMed

Hong, Jinglan; Shi, Wenxiao; Wang, Yutao; Chen, Wei; Li, Xiangzhi

2015-04-01

Life cycle assessment was conducted to estimate the environmental impact of electronic waste (e-waste) treatment. E-waste recycling with an end-life disposal scenario is environmentally beneficial because of the low environmental burden generated from human toxicity, terrestrial ecotoxicity, freshwater ecotoxicity, and marine ecotoxicity categories. Landfill and incineration technologies have a lower and higher environmental burden than the e-waste recycling with an end-life disposal scenario, respectively. The key factors in reducing the overall environmental impact of e-waste recycling are optimizing energy consumption efficiency, reducing wastewater and solid waste effluent, increasing proper e-waste treatment amount, avoiding e-waste disposal to landfill and incineration sites, and clearly defining the duties of all stakeholders (e.g., manufacturers, retailers, recycling companies, and consumers). Copyright © 2015 Elsevier Ltd. All rights reserved.

A New Method of Space Travel Optimized for Space Tourism and Colonization

NASA Astrophysics Data System (ADS)

Turek, Philip A.

2006-01-01

High costs associated with expendable rockets are stifling the development of permanent space colonies. A new method of space travel is presented that enjoys significantly increased performance and reduced cost relative to competing concepts. Based on recycling the kinetic energy of an arriving spacecraft, up to 200 MW of average electrical power is generated and sustained for 2 minutes, and is immediately applied in launching a departing partner spacecraft. The resulting required delta vee for a round trip between low Earth orbit (LEO) and geosynchronous orbit (GEO) drops from 7.6 km/s to 0.54 km/s when 3 recycling stations with an 80 % energy coupling efficiency are used to exchange kinetic energy between 8 partner spacecraft transiting the same route. This method is well suited for round trip high volume space travel such as space tourism traffic to LEO, lunar orbit, and beyond. As the kinetic energy of an arriving spacecraft is the power source for launching departing spacecraft, nascent lunar colonies can electrically launch 26,000 kg payloads long before sustained 100 MW level power supplies become locally available. A pair of recycling stations at an orbiting space colony construction site provides a resource of net impulse, net torque, and electrical power to the colony irrespective of the contents of the arriving payloads. Kinetic energy recycling technology, configuration, operations, and near Earth applications are described.

Thermodynamic Considerations of Contamination by Alloying Elements of Remelted End-of-Life Nickel- and Cobalt-Based Superalloys

NASA Astrophysics Data System (ADS)

Lu, Xin; Matsubae, Kazuyo; Nakajima, Kenichi; Nakamura, Shinichiro; Nagasaka, Tetsuya

2016-06-01

Cobalt and nickel are high-value commodity metals and are mostly used in the form of highly alloyed materials. The alloying elements used may cause contamination problems during recycling. To ensure maximum resource efficiency, an understanding of the removability of these alloying elements and the controllability of some of the primary alloying elements is essential with respect to the recycling of end-of-life (EoL) nickel- and cobalt-based superalloys by remelting. In this study, the distribution behaviors of approximately 30 elements that are usually present in EoL nickel- and cobalt-based superalloys in the solvent metal (nickel, cobalt, or nickel-cobalt alloy), oxide slag, and gas phases during the remelting were quantitatively evaluated using a thermodynamic approach. The results showed that most of the alloying elements can be removed either in the slag phase or into the gas phase. However, the removal of copper, tin, arsenic, and antimony by remelting is difficult, and they remain as tramp elements during the recycling. On the other hand, the distribution tendencies of iron, molybdenum, and tungsten can be controlled by changing the remelting conditions. To increase the resource efficiency of recycling, preventing contamination by the tramp elements and identifying the alloying compositions of EoL superalloys are significantly essential, which will require the development of efficient prior alloy-sorting systems and advanced separation technologies.

NASA Benefits Earth

NASA Technical Reports Server (NTRS)

Robinson, Julie A.

2009-01-01

This slide presentation reviews several ways in which NASA research has benefited Earth and made life on Earth better. These innovations include: solar panels, recycled pavement, thermometer pill, invisible braces for straightening teeth, LASIK, aerodynamic helmets and tires for bicycles, cataract detection, technology that was used to remove Anthrax spores from mail handling facilities, study of atomic oxygen erosion of materials has informed the restoration of artwork, macroencapsulation (a potential mechanism to deliver anti cancer drugs to specific sites), and research on a salmonella vaccine. With research on the International Space Station just beginning, there will be opportunities for entrepreneurs and other government agencies to access space for their research and development. As well as NASA continuing its own research on human health and technology development.

Progress in the development of Ovonic nickel-metal hydride batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Venkatesan, S.; Corrigan, D.A.; Gifford, P.R.

1993-05-01

Proprietary, multicomponent hydrogen storage alloys using the principles of atomic engineering form the heart of Ovonic Nickel-Metal Hydride (Ni/MH) battery technology. This battery system, in development for 10 years, has been licensed to several manufacturers both for consumer cells and electric vehicle batteries. These cells have achieved a specific energy of over 80 Wh/kg, a peak power in excess of 200 W/kg, and over 1000 cycles at 100% depth of discharge. They also have an intrinsic ability to withstand overcharge and overdischarge abuse. Ovonic Ni/MH batteries are environmentally friendly and can be recycled. Performance data will be presented showing themore » successful scale-up of this technology for electric vehicle applications.« less

Fbis report. Science and technology: Economic review, September 19, 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1995-09-19

;Partial Contents: Germany: Braunschweig University Tests Organic Semiconductors; France: Ariane-5 Tests Suspended; First Tests in Euro-Russian RECORD Rocket Engine Program; France: Renault`s Multi-Model Assembly Line Presented; Germany: New High Speed Trains Under Development; France: Matra Test Drone, Missile Systems; France: Experimental Project for Automobile Recycling; Germany: Survey of Flexible Manufacturing Developments; Germany: Heinrich Hertz Institute Produces Polymer-Based Circuit; French Firms Introduce Computerized Control Room for Nuclear Plants; German Machine Tool Industry Calls for Information Technology Projects; Germany: R&D Achievements in Digital HDTV Reported; Hungary: Secondary Telecommunications Networks Described; EU: Mergers in Pharmaceutical Industry Reported; SGS-Thomson Business Performance Analyzed; Germany`s Siemensmore » Invest Heavily in UK Semiconductor Plant.« less

A hybrid water-splitting cycle using copper sulfate and mixed copper oxides

NASA Technical Reports Server (NTRS)

Schreiber, J. D.; Remick, R. J.; Foh, S. E.; Mazumder, M. M.

1980-01-01

The Institute of Gas Technology has derived and developed a hybrid thermochemical water-splitting cycle based on mixed copper oxides and copper sulfate. Similar to other metal oxide-metal sulfate cycles that use a metal oxide to 'concentrate' electrolytically produced sulfuric acid, this cycle offers the advantage of producing oxygen (to be vented) and sulfur dioxide (to be recycled) in separate steps, thereby eliminating the need of another step to separate these gases. The conceptual process flow-sheet efficiency of the cycle promises to exceed 50%. It has been completely demonstrated in the laboratory with recycled materials. Research in the electrochemical oxidation of sulfur dioxide to produce sulfuric acid and hydrogen performed at IGT indicates that the cell performance goals of 200 mA/sq cm at 0.5 V will be attainable using relatively inexpensive electrode materials.

Enhanced Performance of Recycled Aggregate Concrete with Atomic Polymer Technology

DOT National Transportation Integrated Search

2012-06-01

The atomic polymer technology in form of mesoporous inorganic polymer (MIP) can effectively improve material durability and performance of concrete by dramatically increase inter/intragranular bond strength of concrete at nano-scale. The strategy of ...

Materials Management: State of the Practice 2012

EPA Science Inventory

The report presents an evaluation of six materials management technologies that were assessed with respect to each technology's process, material and energy pathways, commercialization status, and associated economics. The inclusion and implementation of a materials recycling pr...

The Utilization of Urine Processing for the Advancement of Life Support Technologies

NASA Technical Reports Server (NTRS)

Grossi-Soyster, Elysse; Hogan, John; Flynn, Michael

2014-01-01

The success of long-duration missions will depend on resource recovery and the self-sustainability of life support technologies. Current technologies used on the International Space Station (ISS) utilize chemical and mechanical processes, such as filtration, to recover potable water from urine produced by crewmembers. Such technologies have significantly reduced the need for water resupply through closed-loop resource recovery and recycling. Harvesting the important components of urine requires selectivity, whether through the use of membranes or other physical barriers, or by chemical or biological processes. Given the chemical composition of urine, the downstream benefits of urine processing for resource recovery will be critical for many aspects of life support, such as food production and the synthesis of biofuels. This paper discusses the beneficial components of urine and their potential applications, and the challenges associated with using urine for nutrient recycling for space application.

Special Advanced Studies for Pollution Prevention. Delivery Order 0058: The Monitor - Winter 2000

DTIC Science & Technology

2001-04-01

Burning/Open Detonation of Energetic Materials ➨Emission factors from a draft EPA report are incorporated into the guidance Site Restoration ➨Method...Aqueous Cleaner Recycle System Microfiltration Removes oil/grease & TSS from alkaline and acid cleaning baths Commodore Separation Technologies, Inc... Microfiltration Removes all heavy metals from wastewater and recycles water Infinity Chemicals Group Infinity Prep-L Deoxidizing Chemical

A composite material based on recycled tires

NASA Astrophysics Data System (ADS)

Malers, L.; Plesuma, R.; Locmele, L.

2009-01-01

The present study is devoted to the elaboration and investigation of a composite material based on mechanically grinded recycled tires and a polymer binder. The correlation between the content of the binder, some technological parameters, and material properties of the composite was clarified. The apparent density, the compressive stress at a 10% strain, the compressive elastic modulus in static and cyclic loadings, and the insulating properties (acoustic and thermal) were the parameters of special interest of the present investigation. It is found that a purposeful variation of material composition and some technological parameters leads to multifunctional composite materials with different and predictable mechanical and insulation properties.

An economic analysis of the processing technologies in CDW recycling platforms.

PubMed

Oliveira Neto, Raul; Gastineau, Pascal; Cazacliu, Bogdan Grigore; Le Guen, Lauredan; Paranhos, Régis Sebben; Petter, Carlos Otávio

2017-02-01

This paper proposes an economic analysis of three different types of processing in CDW (construction and demolition waste) recycling platforms, according to the sophistication of the processing technologies (current advanced, advanced and advanced sorting). The methodology that is adopted is in the economic evaluation concept of projects and is classified with a scoping study phase. In these contexts, three levels of CDW processing capabilities for recycling platforms are analyzed (100, 300 and 600 thousand tons per year). This article considers databases obtained from similar projects that have been published in the specialized literature; the data sources are primarily from the European continent. The paper shows that current advanced process has better economic performance, in terms of IRR, related to the other two processes. The IRR associated with advanced and advanced sorting processes could be raised by, (i) higher price of secondary primary material, and/or (ii) higher capacity of platforms, and/or (iii) higher sharing of secondary primary material in the total production. The first two points depend on the market conditions (prices and total quantity of CDW available) and (potential) fiscal or incentive policies. The last one depends on technological progress. Copyright © 2016 Elsevier Ltd. All rights reserved.

Sustainability evaluation of essential critical raw materials: cobalt, niobium, tungsten and rare earth elements

NASA Astrophysics Data System (ADS)

Tkaczyk, A. H.; Bartl, A.; Amato, A.; Lapkovskis, V.; Petranikova, M.

2018-05-01

The criticality of raw materials has become an important issue in recent years. As the supply of certain raw materials is essential for technologically-advanced economies, the European Commission and other international counterparts have started several initiatives to secure reliable and unhindered access to raw materials. Such efforts include the EU Raw Materials Initiative, European Innovation Partnership on Raw Materials, US Critical Materials Institute, and others. In this paper, the authors present a multi-faceted and multi-national review of the essentials for the critical raw materials (CRMs) Co, Nb, W, and rare earth elements (REEs). The selected CRMs are of specific interest as they are considered relevant for emerging technologies and will thus continue to be of increasing major economic importance. This paper presents a ‘sustainability evaluation’ for each element, including essential data about markets, applications and recycling, and possibilities for substitution have been summarized and analysed. All the presented elements are vital for the advanced materials and processes upon which modern societies rely. These elements exhibit superior importance in ‘green’ applications and products subject to severe conditions. The annual production quantities are quite low compared to common industrial metals. Of the considered CRMs, only Co and REE gross production exceed 100 000 t. At the same time, the prices are quite high, with W and Nb being in the range of 60 USD kg‑1 and some rare earth compounds costing almost 4000 USD kg‑1. Despite valiant effort, in practice some of the considered elements are de facto irreplaceable for many specialized applications, at today’s technological level. Often, substitution causes a significant loss of quality and performance. Furthermore, possible candidates for substitution may be critical themselves or available in considerably low quantities. It can be concluded that one preferred approach for the investigated elements could be the use of secondary resources derived from recycling. W exhibits the highest recycling rate (37%), whereas Co (16%), Nb (11%) and rare earths (~0%) lag behind. In order to promote recycling of these essential elements, financial incentives as well as an improvement of recycling technologies would be required.

Precious metal recovery from waste printed circuit boards using cyanide and non-cyanide lixiviants--A review.

PubMed

Akcil, Ata; Erust, Ceren; Gahan, Chandra Sekhar; Ozgun, Mehmet; Sahin, Merve; Tuncuk, Aysenur

2015-11-01

Waste generated by the electrical and electronic devices is huge concern worldwide. With decreasing life cycle of most electronic devices and unavailability of the suitable recycling technologies it is expected to have huge electronic and electrical wastes to be generated in the coming years. The environmental threats caused by the disposal and incineration of electronic waste starting from the atmosphere to the aquatic and terrestrial living system have raised high alerts and concerns on the gases produced (dioxins, furans, polybrominated organic pollutants, and polycyclic aromatic hydrocarbons) by thermal treatments and can cause serious health problems if the flue gas cleaning systems are not developed and implemented. Apart from that there can be also dissolution of heavy metals released to the ground water from the landfill sites. As all these electronic and electrical waste do posses richness in the metal values it would be worth recovering the metal content and protect the environmental from the pollution. Cyanide leaching has been a successful technology worldwide for the recovery of precious metals (especially Au and Ag) from ores/concentrates/waste materials. Nevertheless, cyanide is always preferred over others because of its potential to deliver high recovery with a cheaper cost. Cyanidation process also increases the additional work of effluent treatment prior to disposal. Several non-cyanide leaching processes have been developed considering toxic nature and handling problems of cyanide with non-toxic lixiviants such as thiourea, thiosulphate, aqua regia and iodine. Therefore, several recycling technologies have been developed using cyanide or non-cyanide leaching methods to recover precious and valuable metals. Copyright © 2015 Elsevier Ltd. All rights reserved.

Ecology of Flows and Drift Wave Turbulence: Reduced Models and Applications

NASA Astrophysics Data System (ADS)

Huang, Wen-Hsi

A major obstacle to sustainable solar technologies is end-of-life solar modules. In this thesis, a recycling process is proposed for crystalline-Si solar modules. It is a three-step process to break down Si modules and recover various materials. Over 95% of a module by weight can be recovered with this process. Two new technologies are demonstrated to enable the proposed recycling process. One is sequential electrowinning which allows multiple metals to be recovered one by one from Si modules, Ag, Pb, Sn and Cu. The other is sheet resistance monitoring by the 4-point probe which maximizes the amount of solar-grade Si recovered from Si modules with high throughput. The purity of the recovered metals is above 99% and the recovery rate can achieve between 70 80%. The recovered Si meets the specifications for solar-grade Si and at least 91% of Si from c-Si solar cells can be recovered. The recovered Si and metals are new feedstocks to the solar industry and generate over $12/module in revenue. This revenue enables a profitable recycling business for Si modules without any government support. The chemicals for recycling are carefully selected to minimize their environmental impact and also the cost. A network for collecting end-of-life solar modules is proposed based on the current distribution network for solar modules to contain the collection cost. As a result, the proposed recycling process for c-Si modules is technically, environmentally and financially sustainable.

Process Metallurgy an Enabler of Resource Efficiency: Linking Product Design to Metallurgy in Product Centric Recycling

NASA Astrophysics Data System (ADS)

Reuter, Markus; van Schaik, Antoinette

In this paper the link between process metallurgy, classical minerals processing, product centric recycling and urban/landfill mining is discussed. The depth that has to be achieved in urban mining and recycling must glean from the wealth of theoretical knowledge and insight that have been developed in the past in minerals and metallurgical processing. This background learns that recycling demands a product centric approach, which considers simultaneously the multi-material interactions in man-made complex `minerals'. Fast innovation in recycling and urban mining can be achieved by further evolving from this well developed basis, evolving the techniques and tools that have been developed over the years. This basis has already been used for many years to design, operate and control industrial plants for metal production. This has been the basis for Design for Recycling rules for End-of-Life products. Using, among others, the UNEP Metal Recycling report as a basis (authors are respectively Lead and Main authors of report), it is demonstrated that a common theoretical basis as developed in metallurgy and minerals processing can help much to level the playing field between primary processing, secondary processing, recycling, and urban/landfill mining and product design hence enhancing resource efficiency. Thus various scales of detail link product design with metallurgical process design and its fundamentals.

Lunar Contour Crafting: A Novel Technique for ISRU-Based Habitat Development

NASA Technical Reports Server (NTRS)

Khoshnevis, Behrokh; Bodiford, Melanie P.; Burks, Kevin H.; Ethridge, Ed; Tucker, Dennis; Kim, Won; Toutanji, Houssam; Fiske, Michael R.

2005-01-01

1. Habitat Structures at MSFC is one element of the In-Situ Fabrication and Repair (ISFR) Program: ISFR develops technologies for fabrication, repair and recycling of tools, parts, and habitats/structures using in-situ resources. ISRU - based habitat structures are considered Class III. 2. Habitat Structure Purpose: Develop Lunar and/or Martian habitat structures for manned missions that maximize the use of in-situ resources to address the following agency topics: bioastronautics critical path roadmap; strategic technical challenges defined in H&RT formulation plan: margins and redundancy; modularity, robotic network, space resource utilization; autonomy, affordable logistics pre-positioning.

Changing patterns in the use, recycling, and material substitution of mercury in the United States

USGS Publications Warehouse

Wilburn, David R.

2013-01-01

Environmental concerns have led to numerous regulations that have dramatically decreased the reported production and use of mercury in the United States since the 1980s. Government legislation and subsequent industry actions have led to increased collection of mercury-containing materials and the recovery of mercury through recycling. Mercury emissions have been reduced and effective alternatives to mercury products have been developed for many applications. This study updates and quantifies the changes in demand, supply, use, and material flow for mercury in various sectors in the United States that have taken place since 1996. Nearly all primary mercury produced in the United States is derived as a byproduct of processing of gold and silver ore in Nevada. Since 2001, annual production of mercury from gold and silver mining in Nevada has decreased by 22 percent overall because ore from greater depths containing low grade mercury is recovered, and mercury emissions from this source have decreased by 95 percent as a result of increased regulation and improved collection and suppression technology. The distribution of consumption of mercury in the United States has changed as a result of regulation (elimination of large-scale mercury use in the paint and battery sectors), reduction by consumers (decommissioning of mercury-cell chloralkali manufacturing capacity), and technological advances (improvements in dental, lighting, and wiring sectors). Mercury use in the chloralkali sector, the leading end-use sector in the United States in 1996, has declined by 98 percent from 136 metric tons (t) in 1996 to about 0.3 t in 2010 because of increased processing and recycling efficiencies and plant closures or conversion to other technologies. As plants were closed, mercury recovered from the infrastructure of decommissioned plants has been exported, making the United States a net exporter of mercury, even though no mercury has been produced as the primary product from mines in the United States since 1992. In 1996, the three leading end-use sectors for mercury in the United States were chloralkali manufacturing (accounting for 38 percent of consumption), electrical and electronic instrumentation (13 percent of consumption), and instruments and measuring devices (11 percent of consumption). In 2010, the three leading end-use sectors were dental amalgam (accounting for between 35 and 57 percent of consumption), electrical and electronic instrumentation (29 percent of consumption), and batteries (8 percent of consumption). Mercury use in lighting is increasing because incandescent lights are being phased out in favor of mercury-containing compact fluorescent bulbs, but the demand for mercury per unit produced is small. Dental amalgam constituted the largest amount of mercury in use in the United States. One study reported about 290 t of mercury in dental amalgam was estimated to be contained in human mouths, an estimated 30 t of mercury amalgam was treated as waste, 28.5 t of mercury amalgam was released to the environment, 6 t of amalgam was recycled, and 3.5 t was treated and stored in landfills in 2009. Mercury contained in products recovered by State, municipal, or industry collection activities is recycled, but the estimated overall recycling rate is less than 10 percent. Increasingly, the U.S. mercury recycling industry has been processing a significant amount of mercury-containing material derived from foreign gold mining operations or decommissioned mercury-cell chloralkali plants. Regulation of mercury export and storage is expected to result in surplus mercury inventories in the United States. The Mercury Export Ban Act of 2008 limits elemental mercury exports for unregulated uses such as artisanal gold mining after January 1, 2013, and requires development of adequate long-term storage facilities in the United States for elemental mercury. During the past 4 years, producers and recyclers of elemental mercury have been exporting large quantities of mercury in anticipation of this regulation, but the U.S. inventory of mercury in 2010 was estimated to have exceeded 7,000 t from Government stockpiles and industry stocks. Costs attributed to long-term storage may affect the competitiveness of mercury recycling.

New generation nuclear fuel structures: Dense particles in selectively soluble matrix

NASA Astrophysics Data System (ADS)

Devlin, Dave; Jarvinen, Gordon; Patterson, Brian; Pattillo, Steve; Valdez, James; Liu, X.-Y.; Phillips, Jonathan

2009-11-01

We have developed a technology for dispersing sub-millimeter sized fuel particles within a bulk matrix that can be selectively dissolved. This may enable the generation of advanced nuclear fuels with easy separation of actinides and fission products. The large kinetic energy of the fission products results in most of them escaping from the sub-millimeter sized fuel particles and depositing in the matrix during burning of the fuel in the reactor. After the fuel is used and allowed to cool for a period of time, the matrix can be dissolved and the fission products removed for disposal while the fuel particles are collected by filtration for recycle. The success of such an approach would meet a major goal of the GNEP program to provide advanced recycle technology for nuclear energy production. The benefits of such an approach include (1) greatly reduced cost of the actinide/fission product separation process, (2) ease of recycle of the fuel particles, and (3) a radiation barrier to prevent theft or diversion of the recycled fuel particles during the time they are re-fabricated into new fuel. In this study we describe a method to make surrogate nuclear fuels of micrometer scale W (shell)/Mo (core) or HfO 2 particles embedded in an MgO matrix that allows easy separation of the fission products and their embedded particles. In brief, the method consists of physically mixing W-Mo or hafnia particles with an MgO precursor. Heating the mixture, in air or argon, without agitation, to a temperature is required for complete decomposition of the precursor. The resulting material was examined using chemical analysis, scanning electron microscopy, X-ray diffraction and micro X-ray computed tomography and found to consist of evenly dispersed particles in an MgO + matrix. We believe this methodology can be extended to actinides and other matrix materials.

Hydroprocessing full-range of heavy oils and bitumen using ultradispersed catalysts at low severity

NASA Astrophysics Data System (ADS)

Peluso, Enzo

The progressive exhaustion of light crude oils is forcing the petroleum industry to explore new alternatives for the exploitation of unconventional oils. New approaches are searching for technologies able to produce, transport and refine these feedstocks at lower costs, in which symbiotic processes between the enhanced oil recovery (EOR) and the conventional upgrading technologies are under investigation. The process explored in this thesis is an interesting alternative for in-situ upgrading of these crude oils in the presence of ultradispersed (UD) catalysts, which are included as a disperse phase able to circulate along with the processed feed. The objectives of this work are: (a) study the performance of UD catalysts in the presence of a full range (non fractioned) heavy oil and bitumen and (b) evaluate the recyclability of the UD catalysts. Four different heavy crude oils were evaluated in the presence with UD catalysts at a total pressure of 2.8 MPa, residence time of 8 hours and reaction temperatures from 360 up to 400ºC. Thermal and catalytic hydro-processing were compared in terms of conversion and product stability. A comparison between the different crude oils was additionally derived in terms of SARA, initial micro-carbon content and virgin oil stability among other properties. Advantages of catalytic hydro-processing over thermal hydro-processing were evidenced, with UD catalysts playing an essential hydrogenating role while retarding coke formation; microcarbon and asphaltenes reduction in the presence of UD catalysts was observed. To evaluate the feasibility of recycling the UD catalysts, a micro-slurry recycled unit was developed as part of this research. These main results showed: (a) a successful design of this unit, (b) that temperature, LHSV and fractional recycling ratio have more impact on VGO conversion, while pressure has almost no effect, and (c) an UD catalysts agglomeration process was detected, however this process is slow and reversible.

INVESTIGATION OF CLEANER TECHNOLOGIES TO MINIMIZE AUTOMOTIVE COOLANT WASTES

EPA Science Inventory

The US Environmental Protection Agency in cooperation with the State of New Jersey evaluated chemical filtration and distillation technologies designed to recycle automotive and heavy-duty engine coolants. These evaluations addressed the product quality, waste reduction and econo...

Opportunities for the Multi Recycling of Used MOX Fuel in the US - 12122

DOE Office of Scientific and Technical Information (OSTI.GOV)

Murray, P.; Bailly, F.; Bouvier, E.

Over the last 50 years the US has accumulated an inventory of used nuclear fuel (UNF) in the region of 64,000 metric tons in 2010, and adds an additional 2,200 metric tons each year from the current fleet of 104 Light Water Reactors. This paper considers a fuel cycle option that would be available for a future pilot U.S. recycling plant that could take advantage of the unique opportunities offered by the age and size of the large U.S. UNF inventory. For the purpose of this scenario, recycling of UNF must use the available reactor infrastructure, currently LWR's, and themore » main product of recycling is considered to be plutonium (Pu), recycled into MOX fuel for use in these reactors. Use of MOX fuels must provide the service (burn-up) expected by the reactor operator, with the required level of safety. To do so, the fissile material concentration (Pu-239, Pu-241) in the MOX must be high enough to maintain criticality, while, in current recycle facilities, the Pu-238 content has to be kept low enough to prevent excessive heat load, neutron emission, and neutron capture during recycle operations. In most countries, used MOX fuel (MOX UNF) is typically stored after one irradiation in an LWR, pending the development of the GEN IV reactors, since it is considered difficult to directly reuse the recycled MOX fuel in LWRs due to the degraded Pu fissile isotopic composition. In the US, it is possible to blend MOX UNF with LEUOx UNF from the large inventory, using the oldest UNF first. Blending at the ratio of about one MOX UNF assembly with 15 LEUOx UNF assemblies, would achieve a fissile plutonium concentration sufficient for reirradiation in new MOX fuel. The Pu-238 yield in the new fuel will be sufficiently low to meet current fuel fabrication standards. Therefore, it should be possible in the context of the US, for discharged MOX fuel to be recycled back into LWR's, using only technologies already industrially deployed worldwide. Building on that possibility, two scenarios are assessed where current US inventory is treated; Pu recycled in LWR MOX fuels, and used MOX fuels themselves are treated in a continuous partitioning-transmutation mode (case 2a) or until the whole current UNF inventory (64,000 MT in 2010) has been treated followed by disposal of the MOX UNF to a geologic repository (case 2b). In the recycling scenario, two cases (2a and 2b) are considered. Benefits achieved are compared with the once through scenario (case 1) where UNF in the current US inventory are disposed directly to a geologic repository. For each scenario, the heat load and radioactivity of the high activity wastes disposed to a geologic repository are calculated and the savings in natural resources quantified, and compared with the once-through fuel cycle. Assuming an initial pilot recycling facility with a capacity of 800 metric tons a year of heavy metal begins operation in 2030, ∼8 metric tons per year of Pu is recovered from the LEUOx UNF inventory, and is used to produce fresh MOX fuels. At a later time, additional treatment and recycling capacities are assumed to begin operation, to accommodate blending and recycling of used MOX Pu, up to 2,400 MT/yr treatment capacity to enable processing UNF slightly faster than the rate of generation. Results of this scenario analysis study show the flexibility of the recycling scenarios so that Pu is managed in a way that avoids accumulating used MOX fuels. If at some future date, the decision is made to dispose of the MOX UNF to a geologic repository (case 2b), the scenario is neutral to final repository heat load in comparison to the direct disposal of all UNF (case 1), while diminishing use of natural uranium, enrichment, UNF accumulation, and the volume of HLW. Further recycling of Pu at the end of the scenario (case 2a) would exhibit further benefits. As expected, Pu-241 and Am-241 are the source of long term HLW heat load and Am-241 and Np-237 are the source of long term radiotoxicity. When advanced technology is available, introduction of minor actinide recycling, in addition to Pu recycling, by the end of this scenario, or sooner, would have a major impact on final repository heat load and long term radiotoxicity of the HLW. This scenario is also compatible with a gradual introduction of a small number of FR's for Pu management. (authors)« less

Research and Development of a New Waste Collection Bin to Facilitate Education in Plastic Recycling

ERIC Educational Resources Information Center

Chow, Cheuk-fai; So, Wing-Mui Winnie; Cheung, Tsz-Yan

2016-01-01

Plastic recycling has been an alternative method for solid waste management apart from landfill and incineration. However, recycling quality is affected when all plastics are discarded into a single recycling bin that increases cross contaminations and operation cost to the recycling industry. Following the engineering design process, a new…

Recycling of polyurethanes from laboratory to industry, a journey towards the sustainability.

PubMed

Simón, D; Borreguero, A M; de Lucas, A; Rodríguez, J F

2018-06-01

The recycling of any kind of plastic to convert it in valuable products is one of the main challenges of today's society. Besides, if the recycling process is itself green, then it would be a great achievement. This paper reviews the way covered from the first attempts of reusing the polyurethane (PU) scraps as a filler for cushions to the last chemical routes employing green recycling agents. Polyurethane is the 6th most used polymer all over the world with a production of 18 millions tons per year, which means a daily production of PU specialties greater than 1 million of cubic meters, equivalent to the volume of the Empire State Building. The thermostable nature of the majority of the polyurethanes specialties has made that the preferred solution for their recycling are the chemical recycling processes. Among them, glycolysis is the one that receives a greater attention from an industrial point of view, so this review puts the spotlight on it. However, the existing reviews in literature do not paid a special attention on glycolysis and only give a superficial description of the process. Nevertheless, in the present review, the scientific literature relative to glycolysis is completely reviewed, updated and ordered according the type of PU specialty recycled. Additionally, the other main chemical recycling processes are also revisited in a more extended and deeper way than in the previous approaches to this topic. Moreover, it is crucial to take into account that some of these technologies, which were described in the literature as promising technologies at laboratory scale are now commercial processes running at industrial scale. For that reason, it is essential to remark that the present review comprises not only a detailed state of art of the scientific literature on the subject, also includes a detailed revision of the past and running on pilot plants and industrial facilities, including several patents, which has never been covered in the current literature. Moreover, this review also describes the most recent studies employing crude glycerol (biodiesel subproduct) as an economic, sustainable and environmental friendly cleavage agent, which should lead the way to the industrial implantation of split-phase glycolysis in a near future, providing high quality recovered products, susceptible of replacing raw ones in the synthesis of new PU specialties. What is more, this review intends that any reader could know and understand the reactions involved in the polyurethane chemistry and recycling, the main polyurethanes types and the fundamentals of the recycling strategies in order to comprehend what are the advantages and drawbacks of each recycling process as starting point for looking for new advantageous alternatives from an environmental, technical and economic point of view. Broader context. This paper reviews the main advances in the polyurethane (PU) recycling field, from laboratory and academia processes to pilot plant and industrial scale ones, including the most relevant patents in the subject. Opposite to other common used plastics, PUs are not polymerization but condensation polymers, synthesized from polyols and isocyanates. The wide diversity of polyols and isocyanates allows the synthesis of numerous different compounds covering a huge range of applications. As a direct consequence of their commercial success, an increasing quantity of PU waste is being disposed by landfilling in the last decades. Such waste comprises not only post-consumer products but also scrap from slabstock manufacturing, which can reach the 10% of the total foam production. However, the massive enforcement of the environmental laws is pointing out a new route in the polymer waste removal sector based in the polymer recycling, and this fact has placed the research in waste treatment as one of the most prolific topics nowadays. In fact, polymer recycling processes have experienced a growing attention from the research and industrial worlds as a direct result of the enforcement of the environmental legislations. Hence, it is essential to develop new environmental sustainable recycling processes with the aim of conserving the natural resources, reducing the amount of waste disposed in landfills and enhancing the sustainability for forthcoming generation. Copyright © 2018 Elsevier Ltd. All rights reserved.

Building a Recycling Program: A Case Study in Success.

ERIC Educational Resources Information Center

Sabol, Laurie

1992-01-01

Presents the development and ongoing operation of a library recycling program established at Bowling Green State University in Ohio. Discusses the initiation and projects of the library recycling committee, logistics, and future projections for library recycling operations. (two references) (MCO)

Vacuum pyrolysis characteristics and parameter optimization of recycling organic materials from waste tantalum capacitors.

PubMed

Chen, Zhenyang; Niu, Bo; Zhang, Lingen; Xu, Zhenming

2018-01-15

Recycling rare metal tantalum from waste tantalum capacitors (WTCs) is significant to alleviate the shortage of tantalum resource. However, environmental problems will be caused if the organic materials from WTCs are improperly disposed. This study presented a promising vacuum pyrolysis technology to recycle the organic materials from WTCs. The organics removal rate could reach 94.32wt% according to TG results. The optimal parameters were determined as 425°C, 50Pa and 30min on the basis of response surface methodology (RSM). The oil yield and residual rate was 18.09wt% and 74.94wt%, respectively. All pyrolysis products can be recycled through a reasonable route. Besides, to deeply understand the pyrolysis process, the pyrolysis mechanism was also proposed based on the product and free radical theory. This paper provides an efficient process for recycling the organic material from WTCs, which can facilitate the following tantalum recovery. Copyright © 2017 Elsevier B.V. All rights reserved.

Efficient microplastics extraction from sand. A cost effective methodology based on sodium iodide recycling.

PubMed

Kedzierski, Mikaël; Le Tilly, Véronique; César, Guy; Sire, Olivier; Bruzaud, Stéphane

2017-02-15

Evaluating the microplastics pollution on the shores requires overcoming the technological and economical challenge of efficient plastic extraction from sand. The recovery of dense microplastics requires the use of NaI solutions, a costly process. The aim of this study is to decrease this cost by recycling the NaI solutions and to determine the impact of NaI storage. For studying the NaI recyclability, the solution density and the salt mass have been monitored during ten life cycles. Density, pH and salt mass have been measured for 40days to assess the storage effect. The results show that NaI solutions are recyclable without any density alterations with a total loss of 35.9% after the 10cycles of use. During storage, chemical reactions may appear but are reversible. Consequently, the use of recycling methods allows for a significant cost reduction. How far the plastic extraction by dense solutions is representative is discussed. Copyright © 2016 Elsevier Ltd. All rights reserved.

Developing Interventions to Change Recycling Behaviors: A Case Study of Applying Behavioral Science

ERIC Educational Resources Information Center

Gainforth, Heather L.; Sheals, Kate; Atkins, Lou; Jackson, Richard; Michie, Susan

2016-01-01

The Theoretical Domains Framework (TDF) and the Behavior Change Wheel (BCW) are frameworks that can be used to develop recycling interventions. The aim of this study was to demonstrate the utility of these frameworks for developing recycling interventions. 20 semistructured interviews with university building users were analyzed using the TDF and…

Assessing recycling versus incineration of key materials in municipal waste: The importance of efficient energy recovery and transport distances.

PubMed

Merrild, Hanna; Larsen, Anna W; Christensen, Thomas H

2012-05-01

Recycling of materials from municipal solid waste is commonly considered to be superior to any other waste treatment alternative. For the material fractions with a significant energy content this might not be the case if the treatment alternative is a waste-to-energy plant with high energy recovery rates. The environmental impacts from recycling and from incineration of six material fractions in household waste have been compared through life cycle assessment assuming high-performance technologies for material recycling as well as for waste incineration. The results showed that there are environmental benefits when recycling paper, glass, steel and aluminium instead of incinerating it. For cardboard and plastic the results were more unclear, depending on the level of energy recovery at the incineration plant, the system boundaries chosen and which impact category was in focus. Further, the environmental impact potentials from collection, pre-treatment and transport was compared to the environmental benefit from recycling and this showed that with the right means of transport, recyclables can in most cases be transported long distances. However, the results also showed that recycling of some of the material fractions can only contribute marginally in improving the overall waste management system taking into consideration their limited content in average Danish household waste. Copyright © 2012 Elsevier Ltd. All rights reserved.

Emergy analysis of the recycling options for construction and demolition waste.

PubMed

Yuan, Fang; Shen, Li-yin; Li, Qi-ming

2011-12-01

Construction and demolition (C&D) waste is becoming a major contributor to environmental pollution. In Shanghai, China, the quantity of C&D waste is 2.11E+07 t/yr, which accounts for 45% of the total quantity of solid waste. There has been a growing promotion of recycling C&D waste as an effective way to solve this waste problem. However, the evaluation of the efficiency of recycling C&D waste as a potential source of resources is largely based on traditional economic analysis. The economic analysis emphasizes money instead of the harmony between economic benefit and environmental effects. There is a need for a new strategic approach to investigate the efficiency of recycling C&D waste to achieve the integration between economic, social and environmental effects. Emergy theory can be employed to analyze different recycling options for C&D waste. With reference to the Chinese construction industry, this paper demonstrates that the close-loop recycling option is better than the open-loop recycling option for C&D waste in terms of the integration of social, environmental and sustainable aspects. To evaluate different technology solutions for C&D waste recycling, the emergy theory and method is not limited to a cost-benefit balance but can include economic, social, environmental and sustainable effects. Copyright © 2011 Elsevier Ltd. All rights reserved.

Developing improved opportunities for the recycling and reuse of materials in road, bridge, and construction projects.

DOT National Transportation Integrated Search

2014-12-01

The use of recycled and reused materials in transportation construction reduces consumption of non-renewable : resources. The objective of this research was to develop opportunities for improving the recycling and reuse of : materials in road and bri...

Contribution of cooperative sector recycling to greenhouse gas emissions reduction: A case study of Ribeirão Pires, Brazil

DOE Office of Scientific and Technical Information (OSTI.GOV)

King, Megan F., E-mail: mfking@uvic.ca; Gutberlet, Jutta, E-mail: gutber@uvic.ca

Highlights: • Cooperative recycling achieves environmental, economic and social objectives. • We calculate GHG emissions reduction for a recycling cooperative in São Paulo, Brazil. • The cooperative merits consideration as a Clean Development Mechanism (CDM) project. • A CDM project would enhance the achievements of the recycling cooperative. • National and local waste management policies support the recycling cooperative. - Abstract: Solid waste, including municipal waste and its management, is a major challenge for most cities and among the key contributors to climate change. Greenhouse gas emissions can be reduced through recovery and recycling of resources from the municipal solidmore » waste stream. In São Paulo, Brazil, recycling cooperatives play a crucial role in providing recycling services including collection, separation, cleaning, stocking, and sale of recyclable resources. The present research attempts to measure the greenhouse gas emission reductions achieved by the recycling cooperative Cooperpires, as well as highlight its socioeconomic benefits. Methods include participant observation, structured interviews, questionnaire application, and greenhouse gas accounting of recycling using a Clean Development Mechanism methodology. The results show that recycling cooperatives can achieve important energy savings and reductions in greenhouse gas emissions, and suggest there is an opportunity for Cooperpires and other similar recycling groups to participate in the carbon credit market. Based on these findings, the authors created a simple greenhouse gas accounting calculator for recyclers to estimate their emissions reductions.« less

An Assessment of the Technical Readiness of the Vapor Phase Catalytic Ammonia Removal Process (VPCAR) Technology

NASA Technical Reports Server (NTRS)

Flynn, Michael

2000-01-01

This poster provides an assessment of the technical readiness of the Vapor Phase Catalytic Ammonia Removal Process (VPCAR). The VPCAR technology is a fully regenerative water recycling technology designed specifically for applications such as a near term Mars exploration mission. The VPCAR technology is a highly integrated distillation/catalytic oxidation based water processor. It is designed to accept a combined wastewater stream (urine, condensate, and hygiene) and produces potable water in a single process step which requires -no regularly scheduled re-supply or maintenance for a 3 year mission. The technology is designed to be modular and to fit into a volume comparable to a single International Space Station Rack (when sized for a crew of 6). This poster provides a description of the VPCAR technology and a summary of the current performance of the technology. Also provided are the results of two separate NASA sponsored system trade studies which investigated the potential payback of further development of the VPCAR technology.

Integral approaches to wastewater treatment plant upgrading for odor prevention: Activated Sludge and Oxidized Ammonium Recycling.

PubMed

Estrada, José M; Kraakman, N J R; Lebrero, R; Muñoz, R

2015-11-01

Traditional physical/chemical end-of-the-pipe technologies for odor abatement are relatively expensive and present high environmental impacts. On the other hand, biotechnologies have recently emerged as cost-effective and environmentally friendly alternatives but are still limited by their investment costs and land requirements. A more desirable approach to odor control is the prevention of odorant formation before being released to the atmosphere, but limited information is available beyond good design and operational practices of the wastewater treatment process. The present paper reviews two widely applicable and economic alternatives for odor control, Activated Sludge Recycling (ASR) and Oxidized Ammonium Recycling (OAR), by discussing their fundamentals, key operating parameters and experience from the available pilot and field studies. Both technologies present high application potential using readily available plant by-products with a minimum plant upgrading, and low investment and operating costs, contributing to the sustainability and economic efficiency of odor control at wastewater treatment facilities. Copyright © 2015 Elsevier Ltd. All rights reserved.

Proposed industrial recovered materials utilization targets for the metals and metal-products industry

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1979-05-01

The introductory chapter provides a discussion of the factors that affect the recovery and reuse of secondary materials and the competition between the primary and secondary metals industries. It discusses these industries in terms of resource characteristics, industry technology, pollution control requirements, market structure, the economics of recycling, and the issues involved in econometrically estimating scrap supply response behavior. It further presents the methodology established by DOE for the metals, textiles, rubber, and pulp and paper industries. The areas in which government policies might have a significant impact on the utilization of primary and secondary metals and on any recyclingmore » targets between now and 1987 are noted. Chapter 3 presents general profiles for the major industrial segments comprising SIC 33. The profiles include such topics as industry structure, process technology, materials and recycling flow, and future trends. Chapter 4 specifically covers the evaluation of recycling targets for the ferrous, aluminum, copper, zinc, and lead industries. (MCW)« less

Are Cellulose Nanofibers a Solution for a More Circular Economy of Paper Products?

PubMed

Delgado-Aguilar, Marc; Tarrés, Quim; Pèlach, M Àngels; Mutjé, Pere; Fullana-I-Palmer, Pere

2015-10-20

This paper presents the study of the feasibility of incorporating lignocellulosic nanofibers (LCNF) to paper in order to maintain the relevant physical properties and increase the number of cycles that paper can be recycled in the technosphere in a more circular economy. For that purpose, the effect of mechanical refining in recycling processes was compared with that of the novel LCNF addition. In this sense, the behavior of a bleached kraft hardwood pulp when recycled was investigated, as well as the effects of each methodology. Since there are many issues to be considered when trying to replace a technology, the present paper analyses its feasibility from a technical and environmental point of view. Technically, LCNF present greater advantages against mechanical refining, such as higher mechanical properties and longer durability of the fibers. A preliminary life cycle assessment showed that the environmental impacts of both systems are very similar; however, changing the boundary conditions to some feasible future scenarios, led to demonstrate that the CNF technology may improve significantly those impacts.

Constrained recycling: a framework to reduce landfilling in developing countries.

PubMed

Diaz, Ricardo; Otoma, Suehiro

2013-01-01

This article presents a model that integrates three branches of research: (i) economics of solid waste that assesses consumer's willingness to recycle and to pay for disposal; (ii) economics of solid waste that compares private and social costs of final disposal and recycling; and (iii) theories on personal attitudes and social influence. The model identifies two arenas where decisions are made: upstream arena, where residents are decision-makers, and downstream arena, where municipal authorities are decision-makers, and graphically proposes interactions between disposal and recycling, as well as the concept of 'constrained recycling' (an alternative to optimal recycling) to guide policy design. It finally concludes that formative instruments, such as environmental education and benchmarks, should be combined with economic instruments, such as subsidies, to move constraints on source separation and recycling in the context of developing countries.

Green Aerospace Fuels from Nonpetroleum Sources

NASA Technical Reports Server (NTRS)

Hepp, Aloysius F.; Kulis, Michael J.; DeLaRee, Ana B.; Zubrin, Robert; Berggren, Mark; Hensel, Joseph D.; Kimble, Michael C.

2011-01-01

Efforts to produce green aerospace propellants from nonpetroleum sources are outlined. The paper begins with an overview of feedstock processing and relevant small molecule or C1 chemistry. Gas-to-liquid technologies, notably Fischer-Tropsch (FT) processing of synthesis gas (CO and H2), are being optimized to enhance the fraction of product stream relevant to aviation (and other transportation) fuels at the NASA Glenn Research Center (GRC). Efforts to produce optimized catalysts are described. Given the high cost of space launch, the recycling of human metabolic and plastic wastes to reduce the need to transport consumables to orbit to support the crew of a space station has long been recognized as a high priority. If the much larger costs of transporting consumables to the Moon or beyond are taken into account, the importance of developing waste recycling systems becomes still more imperative. One promising way to transform organic waste products into useful gases is steam reformation; this well-known technology is currently being optimized by a Colorado company for exploration and planetary surface operations. Reduction of terrestrial waste streams while producing energy and/or valuable raw materials is an opportunity being realized by a new generation of visionary entrepreneurs. A technology that has successfully demonstrated production of fuels and related chemicals from waste plastics developed in Northeast Ohio is described. Technologies being developed by a Massachusetts company to remove sulfur impurities are highlighted. Common issues and concerns for nonpetroleum fuel production are emphasized. Energy utilization is a concern for production of fuels whether a terrestrial operation or on the lunar (or Martian) surface; the term green relates to not only mitigating excess carbon release but also to the efficiency of grid-energy usage. For space exploration, energy efficiency can be an essential concern. Other issues of great concern include minimizing impurities in the product stream(s), especially those that potential health risks and/or could degrade operations through catalyst poisoning or equipment damage. The potential impacts on future missions by such concerns are addressed in closing.

Next Generation Life Support Project Status

NASA Technical Reports Server (NTRS)

Barta, Daniel J.; Chullen, Cinda; Pickering, Karen D.; Cox, Marlon; Towsend, Neil; Campbell, Colin; Flynn, Michael; Wheeler, Raymond

2012-01-01

Next Generation Life Support (NGLS) is one of several technology development projects sponsored by NASA s Game Changing Development Program. The NGLS Project is developing life support technologies (including water recovery and space suit life support technologies) needed for humans to live and work productively in space. NGLS has three project tasks: Variable Oxygen Regulator (VOR), Rapid Cycle Amine (RCA) swing bed, and Alternative Water Processor (AWP). The RCA swing bed and VOR tasks are directed at key technology needs for the Portable Life Support System (PLSS) for an Advanced Extravehicular Mobility Unit, with focus on test article development and integrated testing in an Advanced PLSS in cooperation with the Advanced Extra Vehicular Activity (EVA) Project. An RCA swing-bed provides integrated carbon dioxide removal and humidity control that can be regenerated in real time during an EVA. The VOR technology will significantly increase the number of pressure settings available to the space suit. Current space suit pressure regulators are limited to only two settings whereas the adjustability of the advanced regulator will be nearly continuous. The AWP effort, based on natural biological processes and membrane-based secondary treatment, will result in the development of a system capable of recycling wastewater from sources expected in future exploration missions, including hygiene and laundry water. This paper will provide a status of technology development activities and future plans.

The development and prospects of the end-of-life vehicle recycling system in Taiwan.

PubMed

Chen, Kuan-chung; Huang, Shih-han; Lian, I-wei

2010-01-01

Automobiles usually contain toxic substances, such as lubricants, acid solutions and coolants. Therefore, inappropriate handling of end-of-life vehicles (ELVs) will result in environmental pollution. ELV parts, which include metallic and non-metallic substances, are increasingly gaining recycling value due to the recent global shortage of raw materials. Hence, the establishment of a proper recycling system for ELVs will not only reduce the impact on the environment during the recycling process, but it will also facilitate the effective reuse of recycled resources. Prior to 1994, the recycling of ELVs in Taiwan was performed by related operators in the industry. Since the publishing of the "End-of-life vehicle recycling guidelines" under the authority of the Waste Disposal Act by the Environmental Protection Administration (EPA) in 1994, the recycling of ELVs in Taiwan has gradually become systematic. Subsequently, the Recycling Fund Management Board (RFMB) of the EPA was established in 1998 to collect a Collection-Disposal-Treatment Fee (recycling fee) from responsible enterprises for recycling and related tasks. Since then, the recycling channels, processing equipment, and techniques for ELVs in Taiwan have gradually become established. This paper reviews the establishment of the ELV recycling system, analyzes the current system and its performance, and provides some recommendations for future development. The reduction of auto shredder residue (ASR) is a key factor in maximizing the resource recovery rate and recycling efficiency. The RFMB needs to provide strong economic incentives to further increase the recycling rate and to encourage the automobile industry to design and market greener cars. 2010 Elsevier Ltd. All rights reserved.

Dealing with emerging waste streams: used tyre assessment in Thailand using material flow analysis.

PubMed

Jacob, Paul; Kashyap, Prakriti; Suparat, Tasawan; Visvanathan, Chettiyappan

2014-09-01

Increasing urbanisation and automobile use have given rise to an increase in global tyre waste generation. A tyre becomes waste once it wears out and is no longer fit for its original purpose, and is thus in its end-of-life state. Unlike in developed countries, where waste tyre management has already become a significant issue, it is rarely a priority waste stream in developing countries. Hence, a large quantity of waste tyres ends up either in the open environment or in landfill. In Thailand, waste tyre management is in its infancy, with increased tyre production and wider use of vehicles, but low levels of recycling, leaving scope for more appropriate policies, plans and strategies to increase waste tyre recycling. This article describes the journey of waste tyres in Thailand in terms of recycling and recovery, and disposal. Material flow analysis was used as a tool to quantify the flows and accumulation of waste tyres in Thailand in 2012. The study revealed that, in Thailand in 2012, waste tyre management was still biased towards destructive technologies (48.9%), rather than material recovery involving rubber reclamation, retreading tyres and whole and shredded tyre applications (6.7%). Despite having both economic and environmental benefits, 44.4% of used tyres in 2012 were dumped in the open environment, and the remaining 0.05% in landfills. © The Author(s) 2014.

77 FR 6122 - Providing Refurbishment Services to Federal Agencies

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-07

... equipment? 5. Describe the process for disposing and recycling of failed equipment. Have all facilities in your recycling and disposal process been certified to safely recycle and manage electronics? If so... firms offering refurbishment services, including those developed specifically for recycling facilities...

Manufacturing a 9-Meter Thermoplastic Composite Wind Turbine Blade: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Murray, Robynne; Snowberg, David R; Berry, Derek S

Currently, wind turbine blades are manufactured from a combination of glass and/or carbon fiber composite materials with a thermoset resin such as epoxy, which requires energy-intensive and expensive heating processes to cure. Newly developed in-situ polymerizing thermoplastic resin systems for composite wind turbine blades polymerize at room temperature, eliminating the heating process and significantly reducing the blade manufacturing cycle time and embodied energy, which in turn reduces costs. Thermoplastic materials can also be thermally welded, eliminating the need for adhesive bonds between blade components and increasing the overall strength and reliability of the blades. As well, thermoplastic materials enable end-of-lifemore » blade recycling by reheating and decomposing the materials, which is a limitation of existing blade technology. This paper presents a manufacturing demonstration for a 9-m-long thermoplastic composite wind turbine blade. This blade was constructed in the Composites Manufacturing Education and Technology facility at the National Wind Technology Center at the National Renewable Energy Laboratory (NREL) using a vacuum-assisted resin transfer molding process. Johns Manville fiberglass and an Arkema thermoplastic resin called Elium were used. Additional materials included Armacell-recycled polyethylene terephthalate foam from Creative Foam and low-cost carbon- fiber pultruded spar caps (manufactured in collaboration with NREL, Oak Ridge National Laboratory, Huntsman, Strongwell, and Chomarat). This paper highlights the development of the thermoplastic resin formulations, including an additive designed to control the peak exothermic temperatures. Infusion and cure times of less than 3 hours are also demonstrated, highlighting the efficiency and energy savings associated with manufacturing thermoplastic composite blades.« less

From wastewater to fertilisers--Technical overview and critical review of European legislation governing phosphorus recycling.

PubMed

Hukari, Sirja; Hermann, Ludwig; Nättorp, Anders

2016-01-15

The present paper is based on an analysis of the EU legislation regulating phosphorus recovery and recycling from wastewater stream, in particular as fertiliser. To recover phosphorus, operators need to deal with market regulations, health and environment protection laws. Often, several permits and lengthy authorisation processes for both installation (e.g. environmental impact assessment) and the recovered phosphorus (e.g. End-of-Waste, REACH) are required. Exemptions to certain registration processes for recoverers are in place but rarely applied. National solutions are often needed. Emerging recovery and recycling sectors are affected by legislation in different ways: Wastewater treatment plants are obliged to remove phosphorus but may also recover it in low quantities for operational reasons. Permit processes allowing recovery and recycling operations next to water purification should thus be rationalised. In contrast, the fertiliser industry relies on legal quality requirements, ensuring their market reputation. For start-ups, raw-material sourcing and related legislation will be the key. Phosphorus recycling is governed by fragmented decision-making in regional administrations. Active regulatory support, such as recycling obligation or subsidies, is lacking. Legislation harmonisation, inclusion of recycled phosphorus in existing fertiliser regulations and support of new operators would speed up market penetration of novel technologies, reduce phosphorus losses and safeguard European quality standards.

Applications of CELSS technology to controlled environment agriculture

NASA Technical Reports Server (NTRS)

Bates, Maynard E.; Bubenheim, David L.

1991-01-01

Controlled environment agriculture (CEA) is defined as the use of environmental manipulation for the commercial production of organisms, whether plants or animals. While many of the technologies necessary for aquaculture systems in North America is nevertheless doubling approximately every five years. Economic, cultural, and environmental pressures all favor CEA over field production for many non-commodity agricultural crops. Many countries around the world are already dependent on CEA for much of their fresh food. Controlled ecological life support systems (CELSS), under development at ARC, KSC, and JSC expand the concept of CEA to the extent that all human requirements for food, oxygen, and water will be provided regenerated by processing of waste streams to supply plant inputs. The CELSS will likely contain plants, humans, possibly other animals, microorganisms and physically and chemical processors. In effect, NASA will create engineered ecosystems. In the process of developing the technology for CELSS, NASA will develop information and technology which will be applied to improving the efficiency, reliability, and cost effectiveness for CEA, improving its resources recycling capabilities, and lessening its environmental impact to negligible levels.

Equipment Loan for Concentrated PV Cavity Converter (PVCC) Research: Cooperative Research and Development Final Report, CRADA Number CRD-08-285

DOE Office of Scientific and Technical Information (OSTI.GOV)

Netter, Judy

2015-07-28

Interest in High Concentration Photovoltaics (HCPV) for terrestrial applications has significantly grown in recent years. A major driver behind this growth trend is the availability of high efficiency multi-junction (MJ) cells that promise reliable operation under high concentrations (500 to 1000 suns). The primary impact of HCPV on the solar electricity cost is the dramatic reduction in cell cost. For terrestrial HCPV systems, operating at concentrations ≥ 500 suns, the expensive MJ cells are marginally affordable. Most recently, triple-junction test cells have achieved a conversion efficiency of over 40% under concentrated sunlight. Photovoltaic Cavity Converter (PVCC) is a multi-bandgap, highmore » concentration PV device developed by United Innovations, Inc., under subcontract to NREL. The lateral- (2- dimensional) structure of PVCC, as opposed to vertical multi-junction (MJ) structure, helps to circumvent most of the developmental challenges MJ technology has yet to overcome. This CRADA will allow the continued development of this technology by United Innovations. This project was funded by the California Energy Commission and is the second phase of a twopart demonstration program. The key advantage of the design was the use of a PVCC as the receiver. PVCCs efficiently process highly concentrated solar radiation into electricity by recycling photons that are reflected from the surface of the cells. Conventional flat, twodimensional receivers cannot recycle photons and the reflected photons are lost to the conversion process.« less

Here today, gone tomorrow: biodegradable soft robots

NASA Astrophysics Data System (ADS)

Rossiter, Jonathan; Winfield, Jonathan; Ieropoulos, Ioannis

2016-04-01

One of the greatest challenges to modern technologies is what to do with them when they go irreparably wrong or come to the end of their productive lives. The convention, since the development of modern civilisation, is to discard a broken item and then procure a new one. In the 20th century enlightened environmentalists campaigned for recycling and reuse (R and R). R and R has continued to be an important part of new technology development, but there is still a huge problem of non-recyclable materials being dumped into landfill and being discarded in the environment. The challenge is even greater for robotics, a field which will impact on all aspects of our lives, where discards include motors, rigid elements and toxic power supplies and batteries. One novel solution is the biodegradable robot, an active physical machine that is composed of biodegradable materials and which degrades to nothing when released into the environment. In this paper we examine the potential and realities of biodegradable robotics, consider novel solutions to core components such as sensors, actuators and energy scavenging, and give examples of biodegradable robotics fabricated from everyday, and not so common, biodegradable electroactive materials. The realisation of truly biodegradable robots also brings entirely new deployment, exploration and bio-remediation capabilities: why track and recover a few large non-biodegradable robots when you could speculatively release millions of biodegradable robots instead? We will consider some of these exciting developments and explore the future of this new field.

Teaching with Technology: The Classroom Manager. Cost-Conscious Computing.

ERIC Educational Resources Information Center

Smith, Rhea; And Others

1992-01-01

Teachers discuss how to make the most of technology in the classroom during a tight economy. Ideas include recycling computer printer ribbons, buying replacement batteries for computer power supply packs, upgrading via software, and soliciting donated computer equipment. (SM)

ENVIRONMENTAL TECHNOLOGY VERIFICATION: JOINT (NSF-EPA) VERIFICATION STATEMENT AND REPORT FOR THE REMOVAL OF MERCURY FROM DENTAL OFFICE WASTEWATER, DENTAL RECYCLING OF NORTH AMERICA (DRNA) MERCURY REMOVAL UNIT (MRU). - NSF 02/01/EPAWQPC-SWP

EPA Science Inventory

Verification testing of the Dental Recycling North America (DRNA) Mercury Removal Unit (MRU) was conducted over a seven week period, at a dental office in Michigan that had three operatory rooms and two hygiene rooms. The office operated four days per week and averaged approxiam...

Lost by Design.

PubMed

Ciacci, Luca; Reck, Barbara K; Nassar, N T; Graedel, T E

2015-08-18

In some common uses metals are lost by intent-copper in brake pads, zinc in tires, and germanium in retained catalyst applications being examples. In other common uses, metals are incorporated into products in ways for which no viable recycling approaches exist, examples include selenium in colored glass and vanadium in pigments. To determine quantitatively the scope of these "losses by design", we have assessed the major uses of 56 metals and metalloids, assigning each use to one of three categories: in-use dissipation, currently unrecyclable when discarded, or potentially recyclable when discarded. In-use dissipation affects fewer than a dozen elements (including mercury and arsenic), but the spectrum of elements dissipated increases rapidly if applications from which they are currently unrecyclable are considered. In many cases the resulting dissipation rates are higher than 50%. Among others, specialty metals (e.g., gallium, indium, and thallium) and some heavy rare earth elements are representative of modern technology, and their loss provides a measure of the degree of unsustainability in the contemporary use of materials and products. Even where uses are currently compatible with recycling technologies and approaches, end of life recycling rates are in most cases well below those that are potentially achievable. The outcomes of this research provide guidance in identifying product design approaches for reducing material losses so as to increase element recovery at end-of-life.

Creating Methane from Plastics: Recycling at a Lunar Outpost

NASA Technical Reports Server (NTRS)

Captain, Janine; Santiago, Eddie; Wheeler, Ray; Strayer, RIchard; Garland, Jay; Parrish, Clyde

2010-01-01

The high cost of re-supply from Earth demands resources to be utilized to the fullest extent for exploration missions. Recycling is a key technology that maximizes the available resources by converting waste products into useful commodities. One example of this is to convert crew member waste such as plastic packaging, food scraps, and human waste, into fuel. The ability to refuel on the lunar surface would reduce the vehicle mass during launch and provide excess payload capability. The goal of this project is to determine the feasibility of recycling waste into methane on the lunar outpost by performing engineering assessments and lab demonstrations of the technology. The first goal of the project was to determine how recycling could influence lunar exploration. Table I shows an estimation of the typical dried waste stream generated each day for a crew of four. Packaging waste accounts for nearly 86% of the dry waste stream and is a significant source of carbon on the lunar surface. This is important because methane (CH4) can be used as fuel and no other source of carbon is available on the lunar surface. With the initial assessment indicating there is sufficient resources in the waste stream to provide refueling capabilities, the project was designed to examine the conversion of plastics into methane.

Staged, High-Pressure Oxy-Combustion Technology: Development and Scale-Up

DOE Office of Scientific and Technical Information (OSTI.GOV)

Axelbaum, Richard; Kumfer, Benjamin; Gopan, Akshay

The immediate need for a high efficiency, low cost carbon capture process has prompted the recent development of pressurized oxy-combustion. With a greater combustion pressure the dew point of the flue gas is increased, allowing for effective integration of the latent heat of flue gas moisture into the Rankine cycle. This increases the net plant efficiency and reduces costs. A novel, transformational process, named Staged, Pressurized Oxy-Combustion (SPOC), achieves additional step changes in efficiency and cost reduction by significantly reducing the recycle of flue gas. The research and development activities conducted under Phases I and II of this project (FE0009702)more » include: SPOC power plant cost and performance modeling, CFD-assisted design of pressurized SPOC boilers, theoretical analysis of radiant heat transfer and ash deposition, boiler materials corrosion testing, construction of a 100 kWth POC test facility, and experimental testing. The results of this project have advanced the technology readiness level (TRL) of the SPOC technology from 1 to 5.« less

Bitsy Thinks Big

NASA Technical Reports Server (NTRS)

2001-01-01

AeroAstro, of Herndon, Virginia, developed a nanospacecraft core module capable of developing recyclable spacecraft designs using standard interfaces. From this core module, known as the Bitsy(TM) kernel, custom spacecraft are able to connect mission-specific instruments and subsystems for variation in mission usage. The nanospacecraft core module may be used in conjunction with an existing microsatellite bus or customized to meet specific requirements. Building on this premise, AeroAstro has developed a line of satellite communications equipment, sun sensors, and Lithium-Ion batteries which are all incorporated in its complete line of mission-specific nanospacecraft. The Bitsy technology is also a key component in AeroAstro#s satellite inspection products and orbital transfer services. In the future, AeroAstro plans to market an even less expensive version of the Bitsy technology. The plan, which is targeted to universities, markets a sort of "satellite in a kit," for less than $1 million. This technology would allow universities to build true space hardware for a fraction of the cost of launching a regular satellite.

Accomplishing simple, solubility-based separations of rare earth elements with complexes bearing size-sensitive molecular apertures

PubMed Central

Bogart, Justin A.; Cole, Bren E.; Boreen, Michael A.; Lippincott, Connor A.; Manor, Brian C.; Carroll, Patrick J.; Schelter, Eric J.

2016-01-01

Rare earth (RE) metals are critical components of electronic materials and permanent magnets. Recycling of consumer materials is a promising new source of rare REs. To incentivize recycling, there is a clear need for the development of simple methods for targeted separations of mixtures of RE metal salts. Metal complexes of a tripodal hydroxylaminato ligand, TriNOx3–, featured a size-sensitive aperture formed of its three η2-(N,O) ligand arms. Exposure of cations in the aperture induced a self-associative equilibrium comprising RE(TriNOx)THF and [RE(TriNOx)]2 species. Differences in the equilibrium constants Kdimer for early and late metals enabled simple separations through leaching. Separations were performed on RE1/RE2 mixtures, where RE1 = La–Sm and RE2 = Gd–Lu, with emphasis on Eu/Y separations for potential applications in the recycling of phosphor waste from compact fluorescent light bulbs. Using the leaching method, separations factors approaching 2,000 were obtained for early–late RE combinations. Following solvent optimization, >95% pure samples of Eu were obtained with a 67% recovery for the technologically relevant Eu/Y separation. PMID:27956636

Sustainable Hypersaline Microbial Fuel Cells: Inexpensive Recyclable Polymer Supports for Carbon Nanotube Conductive Paint Anodes.

PubMed

Grattieri, Matteo; Shivel, Nelson D; Sifat, Iram; Bestetti, Massimiliano; Minteer, Shelley D

2017-05-09

Microbial fuel cells are an emerging technology for wastewater treatment, but to be commercially viable and sustainable, the electrode materials must be inexpensive, recyclable, and reliable. In this study, recyclable polymeric supports were explored for the development of anode electrodes to be applied in single-chamber microbial fuel cells operated in field under hypersaline conditions. The support was covered with a carbon nanotube (CNT) based conductive paint, and biofilms were able to colonize the electrodes. The single-chamber microbial fuel cells with Pt-free cathodes delivered a reproducible power output after 15 days of operation to achieve 12±1 mW m -2 at a current density of 69±7 mA m -2 . The decrease of the performance in long-term experiments was mostly related to inorganic precipitates on the cathode electrode and did not affect the performance of the anode, as shown by experiments in which the cathode was replaced and the fuel cell performance was regenerated. The results of these studies show the feasibility of polymeric supports coated with CNT-based paint for microbial fuel cell applications. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

E-waste management and sustainability: a case study in Brazil.

PubMed

Azevedo, Luís Peres; da Silva Araújo, Fernando Gabriel; Lagarinhos, Carlos Alberto Ferreira; Tenório, Jorge Alberto Soares; Espinosa, Denise Crocce Romano

2017-11-01

The advancement of technology and development of new electronic and electrical equipment with a reduced life cycle has increased the need for the disposal of them (called Waste of Electric and Electronic Equipment or simply e-waste) due to defects presented during use, replacement of obsolete equipment, and ease of acquisition of new equipment. There is a lack of consumer awareness regarding the use, handling storage, and disposal of this equipment. In Brazil, the disposal of post-consumer waste is regulated by the National Solid Waste Policy, established by Law No. 12305 and regulated on the 23rd December 2010. Under this legislation, manufacturers and importers are required to perform a project for the Reverse Logistics of e-waste, though its implementation is not well defined. This work focuses on the verification of the sustainability of reverse logistics suggested by the legislation and the mandatory points, evaluating its costs and the possible financial gain with recycling of the waste. The management of reverse logistics and recycling of waste electrical and electronic equipment, or simply recycling of e-waste, as suggested by the government, will be the responsibility of the managing organization to be formed by the manufacturers/importers in Brazil.

Separation and recovery of fine particles from waste circuit boards using an inflatable tapered diameter separation bed.

PubMed

Duan, Chenlong; Sheng, Cheng; Wu, Lingling; Zhao, Yuemin; He, Jinfeng; Zhou, Enhui

2014-01-01

Recovering particle materials from discarded printed circuit boards can enhance resource recycling and reduce environmental pollution. Efficiently physically separating and recovering fine metal particles (-0.5 mm) from the circuit boards are a key recycling challenge. To do this, a new type of separator, an inflatable tapered diameter separation bed, was developed to study particle motion and separation mechanisms in the bed's fluid flow field. For 0.5-0.25 mm circuit board particles, metal recovery rates ranged from 87.56 to 94.17%, and separation efficiencies ranged from 87.71 to 94.20%. For 0.25-0.125 mm particles, metal recovery rates ranged from 84.76 to 91.97%, and separation efficiencies ranged from 84.74 to 91.86%. For superfine products (-0.125 mm), metal recovery rates ranged from 73.11 to 83.04%, and separation efficiencies ranged from 73.00 to 83.14%. This research showed that the inflatable tapered diameter separation bed achieved efficient particle separation and can be used to recover fine particles under a wide range of operational conditions. The bed offers a new mechanical technology to recycle valuable materials from discarded printed circuit boards, reducing environmental pollution.

Accomplishing simple, solubility-based separations of rare earth elements with complexes bearing size-sensitive molecular apertures.

PubMed

Bogart, Justin A; Cole, Bren E; Boreen, Michael A; Lippincott, Connor A; Manor, Brian C; Carroll, Patrick J; Schelter, Eric J

2016-12-27

Rare earth (RE) metals are critical components of electronic materials and permanent magnets. Recycling of consumer materials is a promising new source of rare REs. To incentivize recycling, there is a clear need for the development of simple methods for targeted separations of mixtures of RE metal salts. Metal complexes of a tripodal hydroxylaminato ligand, TriNOx 3- , featured a size-sensitive aperture formed of its three η 2 -(N,O) ligand arms. Exposure of cations in the aperture induced a self-associative equilibrium comprising RE(TriNOx)THF and [RE(TriNOx)] 2 species. Differences in the equilibrium constants K dimer for early and late metals enabled simple separations through leaching. Separations were performed on RE1/RE2 mixtures, where RE1 = La-Sm and RE2 = Gd-Lu, with emphasis on Eu/Y separations for potential applications in the recycling of phosphor waste from compact fluorescent light bulbs. Using the leaching method, separations factors approaching 2,000 were obtained for early-late RE combinations. Following solvent optimization, >95% pure samples of Eu were obtained with a 67% recovery for the technologically relevant Eu/Y separation.

Identification and recovery of rare-earth permanent magnets from waste electrical and electronic equipment.

PubMed

Lixandru, A; Venkatesan, P; Jönsson, C; Poenaru, I; Hall, B; Yang, Y; Walton, A; Güth, K; Gauß, R; Gutfleisch, O

2017-10-01

Nd-Fe-B permanent magnets are a strategic material for a number of emerging technologies. They are a key component in the most energy efficient electric motors and generators, thus, they are vital for energy technologies, industrial applications and automation, and future forms of mobility. Rare earth elements (REEs) such as neodymium, dysprosium and praseodymium are also found in waste electrical and electronic equipment (WEEE) in volumes that grow with the technological evolution, and are marked as critical elements by the European Commission due to their high economic importance combined with significant supply risks. Recycling could be a good approach to compensate for the lack of rare earths (REs) on the market. However, less than 1% of REs are currently being recycled, mainly because of non-existing collection logistics, lack of information about the quantity of RE materials available for recycling and recycling-unfriendly product designs. To improve these lack of information, different waste streams of electrical and electronic equipment from an industrial recycling plant were analyzed in order to localize, identify and collect RE permanent magnets of the Nd-Fe-B type. This particular type of magnets were mainly found in hard disk drives (HDDs) from laptops and desktop computers, as well as in loudspeakers from compact products such as flat screen TVs, PC screens, and laptops. Since HDDs have been investigated thoroughly by many authors, this study focusses on other potential Nd-Fe-B resources in electronic waste. The study includes a systematic survey of the chemical composition of the Nd-Fe-B magnets found in the selected waste streams, which illustrates the evolution of the Nd-Fe-B alloys over the years. The study also provides an overview over the types of magnets integrated in different waste electric and electronic equipment. Copyright © 2017 Elsevier Ltd. All rights reserved.

Continuous downstream processing for high value biological products: A Review.

PubMed

Zydney, Andrew L

2016-03-01

There is growing interest in the possibility of developing truly continuous processes for the large-scale production of high value biological products. Continuous processing has the potential to provide significant reductions in cost and facility size while improving product quality and facilitating the design of flexible multi-product manufacturing facilities. This paper reviews the current state-of-the-art in separations technology suitable for continuous downstream bioprocessing, focusing on unit operations that would be most appropriate for the production of secreted proteins like monoclonal antibodies. This includes cell separation/recycle from the perfusion bioreactor, initial product recovery (capture), product purification (polishing), and formulation. Of particular importance are the available options, and alternatives, for continuous chromatographic separations. Although there are still significant challenges in developing integrated continuous bioprocesses, recent technological advances have provided process developers with a number of attractive options for development of truly continuous bioprocessing operations. © 2015 Wiley Periodicals, Inc.

Electrochemical advanced oxidation processes as decentralized water treatment technologies to remediate domestic washing machine effluents.

PubMed

Dos Santos, Alexsandro Jhones; Costa, Emily Cintia Tossi de Araújo; da Silva, Djalma Ribeiro; Garcia-Segura, Sergi; Martínez-Huitle, Carlos Alberto

2018-03-01

Water scarcity is one of the major concerns worldwide. In order to secure this appreciated natural resource, management and development of water treatment technologies are mandatory. One feasible alternative is the consideration of water recycling/reuse at the household scale. Here, the treatment of actual washing machine effluent by electrochemical advanced oxidation processes was considered. Electrochemical oxidation and electro-Fenton technologies can be applied as decentralized small-scale water treatment devices. Therefore, efficient decolorization and total organic abatement have been followed. The results demonstrate the promising performance of solar photoelectro-Fenton process, where complete color and organic removal was attained after 240 min of treatment under optimum conditions by applying a current density of 66.6 mA cm -2 . Thus, electrochemical technologies emerge as promising water-sustainable approaches.

The Life Cycle Cost (LCC) of Life Support Recycling and Resupply

NASA Technical Reports Server (NTRS)

Jones, Harry W.

2015-01-01

Brief human space missions supply all the crew's water and oxygen from Earth. The multiyear International Space Station (ISS) program instead uses physicochemical life support systems to recycle water and oxygen. This paper compares the Life Cycle Cost (LCC) of recycling to the LCC of resupply for potential future long duration human space missions. Recycling systems have high initial development costs but relatively low durationdependent support costs. This means that recycling is more cost effective for longer missions. Resupplying all the water and oxygen requires little initial development cost but has a much higher launch mass and launch cost. The cost of resupply increases as the mission duration increases. Resupply is therefore more cost effective than recycling for shorter missions. A recycling system pays for itself when the resupply LCC grows greater over time than the recycling LCC. The time when this occurs is called the recycling breakeven date. Recycling will cost very much less than resupply for long duration missions within the Earth-Moon system, such as a future space station or Moon base. But recycling would cost about the same as resupply for long duration deep space missions, such as a Mars trip. Because it is not possible to provide emergency supplies or quick return options on the way to Mars, more expensive redundant recycling systems will be needed.

Yttrium recovery from primary and secondary sources: A review of main hydrometallurgical processes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Innocenzi, Valentina, E-mail: valentina.innocenzi1@univaq.it; De Michelis, Ida; Kopacek, Bernd

2014-07-15

Highlights: • Review of the main hydrometallurgical processes to recover yttrium. • Recovery of yttrium from primary sources. • Recovery of yttrium from e-waste and other types of waste. - Abstract: Yttrium is important rare earths (REs) used in numerous fields, mainly in the phosphor powders for low-energy lighting. The uses of these elements, especially for high-tech products are increased in recent years and combined with the scarcity of the resources and the environmental impact of the technologies to extract them from ores make the recycling waste, that contain Y and other RE, a priority. The present review summarized themore » main hydrometallurgical technologies to extract Y from ores, contaminated solutions, WEEE and generic wastes. Before to discuss the works about the treatment of wastes, the processes to retrieval Y from ores are discussed, since the processes are similar and derived from those already developed for the extraction from primary sources. Particular attention was given to the recovery of Y from WEEE because the recycle of them is important not only for economical point of view, considering its value, but also for environmental impact that this could be generated if not properly disposal.« less

An Improved Multi-Objective Programming with Augmented ε-Constraint Method for Hazardous Waste Location-Routing Problems

PubMed Central

Yu, Hao; Solvang, Wei Deng

2016-01-01

Hazardous waste location-routing problems are of importance due to the potential risk for nearby residents and the environment. In this paper, an improved mathematical formulation is developed based upon a multi-objective mixed integer programming approach. The model aims at assisting decision makers in selecting locations for different facilities including treatment plants, recycling plants and disposal sites, providing appropriate technologies for hazardous waste treatment, and routing transportation. In the model, two critical factors are taken into account: system operating costs and risk imposed on local residents, and a compensation factor is introduced to the risk objective function in order to account for the fact that the risk level imposed by one type of hazardous waste or treatment technology may significantly vary from that of other types. Besides, the policy instruments for promoting waste recycling are considered, and their influence on the costs and risk of hazardous waste management is also discussed. The model is coded and calculated in Lingo optimization solver, and the augmented ε-constraint method is employed to generate the Pareto optimal curve of the multi-objective optimization problem. The trade-off between different objectives is illustrated in the numerical experiment. PMID:27258293

An Improved Multi-Objective Programming with Augmented ε-Constraint Method for Hazardous Waste Location-Routing Problems.

PubMed

Yu, Hao; Solvang, Wei Deng

2016-05-31

Hazardous waste location-routing problems are of importance due to the potential risk for nearby residents and the environment. In this paper, an improved mathematical formulation is developed based upon a multi-objective mixed integer programming approach. The model aims at assisting decision makers in selecting locations for different facilities including treatment plants, recycling plants and disposal sites, providing appropriate technologies for hazardous waste treatment, and routing transportation. In the model, two critical factors are taken into account: system operating costs and risk imposed on local residents, and a compensation factor is introduced to the risk objective function in order to account for the fact that the risk level imposed by one type of hazardous waste or treatment technology may significantly vary from that of other types. Besides, the policy instruments for promoting waste recycling are considered, and their influence on the costs and risk of hazardous waste management is also discussed. The model is coded and calculated in Lingo optimization solver, and the augmented ε-constraint method is employed to generate the Pareto optimal curve of the multi-objective optimization problem. The trade-off between different objectives is illustrated in the numerical experiment.

E-waste: a global hazard.

PubMed

Perkins, Devin N; Brune Drisse, Marie-Noel; Nxele, Tapiwa; Sly, Peter D

2014-01-01

Waste from end-of-life electrical and electronic equipment, known as e-waste, is a rapidly growing global problem. E-waste contains valuable materials that have an economic value when recycled. Unfortunately, the majority of e-waste is recycled in the unregulated informal sector and results in significant risk for toxic exposures to the recyclers, who are frequently women and children. The aim of this study was to document the extent of the problems associated with inappropriate e-waste recycling practices. This was a narrative review that highlighted where e-waste is generated, where it is recycled, the range of adverse environmental exposures, the range of adverse health consequences, and the policy frameworks that are intended to protect vulnerable populations from inappropriate e-waste recycling practices. The amount of e-waste being generated is increasing rapidly and is compounded by both illegal exportation and inappropriate donation of electronic equipment, especially computers, from developed to developing countries. As little as 25% of e-waste is recycled in formal recycling centers with adequate worker protection. The health consequences of both direct exposures during recycling and indirect exposures through environmental contamination are potentially severe but poorly studied. Policy frameworks aimed at protecting vulnerable populations exist but are not effectively applied. E-waste recycling is necessary but it should be conducted in a safe and standardized manor. The acceptable risk thresholds for hazardous, secondary e-waste substances should not be different for developing and developed countries. However, the acceptable thresholds should be different for children and adults given the physical differences and pronounced vulnerabilities of children. Improving occupational conditions for all e-waste workers and striving for the eradication of child labor is non-negotiable. Crown Copyright © 2014. Published by Elsevier Inc. All rights reserved.

Publications of the NASA Controlled Ecological Life Support System (CELSS) Program, 1979-1989

NASA Technical Reports Server (NTRS)

Wallace, Janice S.; Powers, Janet V.

1990-01-01

Publications of research sponsored by the NASA Controlled Ecological Life Support System (CELSS) Program from 1979 to 1989 are listed. The CELSS Program encompasses research and technology with the goal of developing an autonomous bioregenerative life support system that continually recycles the solid, liquid, and gaseous materials essential for human life. The bibliography is divided into four major subject areas: food production, nutritional requirements, waste management, and systems management and control.

Challenges in automatic sorting of construction and demolition waste by hyperspectral imaging

NASA Astrophysics Data System (ADS)

Hollstein, Frank; Cacho, Íñigo; Arnaiz, Sixto; Wohllebe, Markus

2016-05-01

EU-28 countries currently generate 460 Mt/year of construction and demolition waste (C&DW) and the generation rate is expected to reach around 570 Mt/year between 2025 and 2030. There is great potential for recycling C&DW materials since they are massively produced and content valuable resources. But new C&DW is more complex than existing one and there is a need for shifting from traditional recycling approaches to novel recycling solutions. One basic step to achieve this objective is an improvement in (automatic) sorting technology. Hyperspectral Imaging is a promising candidate to support the process. However, the industrial distribution of Hyperspectral Imaging in the C&DW recycling branch is currently insufficiently pronounced due to high investment costs, still insufficient robustness of optical sensor hardware in harsh ambient conditions and, because of the need of sensor fusion, not well-engineered special software methods to perform the (on line) sorting tasks. Thereby frame rates of over 300 Hz are needed for a successful sorting result. Currently the biggest challenges with regard to C&DW detection cover the need of overlapping VIS, NIR and SWIR hyperspectral images in time and space, in particular for selective recognition of contaminated particles. In the study on hand a new approach for hyperspectral imagers is presented by exploiting SWIR hyperspectral information in real time (with 300 Hz). The contribution describes both laboratory results with regard to optical detection of the most important C&DW material composites as well as a development path for an industrial implementation in automatic sorting and separation lines. The main focus is placed on the closure of the two recycling circuits "grey to grey" and "red to red" because of their outstanding potential for sustainability in conservation of construction resources.

Forecasting waste compositions: A case study on plastic waste of electronic display housings.

PubMed

Peeters, Jef R; Vanegas, Paul; Kellens, Karel; Wang, Feng; Huisman, Jaco; Dewulf, Wim; Duflou, Joost R

2015-12-01

Because of the rapid succession of technological developments, the architecture and material composition of many products used in daily life have drastically changed over the last decades. As a result, well-adjusted recycling technologies need to be developed and installed to cope with these evolutions. This is essential to guarantee continued access to materials and to reduce the ecological impact of our material consumption. However, limited information is currently available on the material composition of arising waste streams and even less on how these waste streams will evolve. Therefore, this paper presents a methodology to forecast trends in the material composition of waste streams. To demonstrate the applicability and value of the proposed methodology, it is applied to forecast the evolution of plastic housing waste from flat panel display (FPD) TVs, FPD monitors, cathode ray tube (CRT) TVs and CRT monitors. The results of the presented forecasts indicate that a wide variety of plastic types and additives, such as flame retardants, are found in housings of similar products. The presented case study demonstrates that the proposed methodology allows the identification of trends in the evolution of the material composition of waste streams. In addition, it is demonstrated that the recycling sector will need to adapt its processes to deal with the increasing complexity of plastics of end-of-life electronic displays while respecting relevant directives. Copyright © 2015 Elsevier Ltd. All rights reserved.

Research on the recycling industry development model for typical exterior plastic components of end-of-life passenger vehicle based on the SWOT method.

PubMed

Zhang, Hongshen; Chen, Ming

2013-11-01

In-depth studies on the recycling of typical automotive exterior plastic parts are significant and beneficial for environmental protection, energy conservation, and sustainable development of China. In the current study, several methods were used to analyze the recycling industry model for typical exterior parts of passenger vehicles in China. The strengths, weaknesses, opportunities, and challenges of the current recycling industry for typical exterior parts of passenger vehicles were analyzed comprehensively based on the SWOT method. The internal factor evaluation matrix and external factor evaluation matrix were used to evaluate the internal and external factors of the recycling industry. The recycling industry was found to respond well to all the factors and it was found to face good developing opportunities. Then, the cross-link strategies analysis for the typical exterior parts of the passenger car industry of China was conducted based on the SWOT analysis strategies and established SWOT matrix. Finally, based on the aforementioned research, the recycling industry model led by automobile manufacturers was promoted. Copyright © 2013 Elsevier Ltd. All rights reserved.

Hydrogen Purification and Recycling for an Integrated Oxygen Recovery System Architecture

NASA Technical Reports Server (NTRS)

Abney, Morgan B.; Greenwood, Zachary; Wall, Terry; Miller, Lee; Wheeler, Ray

2016-01-01

The United States Atmosphere Revitalization life support system on the International Space Station (ISS) performs several services for the crew including oxygen generation, trace contaminant control, carbon dioxide (CO2) removal, and oxygen recovery. Oxygen recovery is performed using a Sabatier reactor developed by Hamilton Sundstrand, wherein CO2 is reduced with hydrogen in a catalytic reactor to produce methane and water. The water product is purified in the Water Purification Assembly and recycled to the Oxygen Generation Assembly (OGA) to provide O2 to the crew. This architecture results in a theoretical maximum oxygen recovery from CO2 of approximately 54% due to the loss of reactant hydrogen in Sabatier-produced methane that is currently vented outside of ISS. Plasma Methane Pyrolysis technology (PPA), developed by Umpqua Research Company, provides the capability to further close the Atmosphere Revitalization oxygen loop by recovering hydrogen from Sabatier-produced methane. A key aspect of this technology approach is to purify the hydrogen from the PPA product stream which includes acetylene, unreacted methane and byproduct water and carbon monoxide. In 2015, four sub-scale hydrogen separation systems were delivered to NASA for evaluation. These included two electrolysis single-cell hydrogen purification cell stacks developed by Sustainable Innovations, LLC, a sorbent-based hydrogen purification unit using microwave power for sorbent regeneration developed by Umpqua Research Company, and a LaNi4.6Sn0.4 metal hydride produced by Hydrogen Consultants, Inc. Here we report the results of these evaluations, discuss potential architecture options, and propose future work.

Hydrogen Purification and Recycling for an Integrated Oxygen Recovery System Architecture

NASA Technical Reports Server (NTRS)

Abney, Morgan B.; Greenwood, Zachary; Wall, Terry; Nur, Mononita; Wheeler, Richard R., Jr.; Preston, Joshua; Molter, Trent

2016-01-01

The United States Atmosphere Revitalization life support system on the International Space Station (ISS) performs several services for the crew including oxygen generation, trace contaminant control, carbon dioxide (CO2) removal, and oxygen recovery. Oxygen recovery is performed using a Sabatier reactor developed by Hamilton Sundstrand, wherein CO2 is reduced with hydrogen in a catalytic reactor to produce methane and water. The water product is purified in the Water Purification Assembly and recycled to the Oxygen Generation Assembly (OGA) to provide O2 to the crew. This architecture results in a theoretical maximum oxygen recovery from CO2 of approx.54% due to the loss of reactant hydrogen in Sabatier-produced methane that is currently vented outside of ISS. Plasma Pyrolysis Assembly (PPA) technology, developed by Umpqua Research Company, provides the capability to further close the Atmosphere Revitalization oxygen loop by recovering hydrogen from Sabatier-produced methane. A key aspect of this technology approach is the need to purify the hydrogen from the PPA product stream which includes acetylene, unreacted methane and byproduct water and carbon monoxide. In 2015, four sub-scale hydrogen separation systems were delivered to NASA for evaluation. These included two electrolysis single-cell hydrogen purification cell stacks developed by Sustainable Innovations, LLC, a sorbent-based hydrogen purification unit using microwave power for sorbent regeneration developed by Umpqua Research Company, and a LaNi4.6Sn0.4 metal hydride produced by Hydrogen Consultants, Inc. Here we report the results of these evaluations to-date, discuss potential architecture options, and propose future work.

Application of visible spectroscopy in waste sorting

NASA Astrophysics Data System (ADS)

Spiga, Philippe; Bourely, Antoine

2011-10-01

Today, waste recycling, (bottles, papers...), is a mechanical operation: the waste are crushed, fused and agglomerated in order to obtain new manufactured products (e.g. new bottles, clothes ...). The plastics recycling is the main application in the color sorting process. The colorless plastics recovered are more valuable than the colored plastics. Other emergent applications are in the paper sorting, where the main goal is to sort dyed paper from white papers. Up to now, Pellenc Selective Technologies has manufactured color sorting machines based on RGB cameras. Three dimensions (red, green and blue) are no longer sufficient to detect low quantities of dye in the considered waste. In order to increase the efficiency of the color detection, a new sorting machine, based on visible spectroscopy, has been developed. This paper presents the principles of the two approaches and their difference in terms of sorting performance, making visible spectroscopy a clear winner.

Utilization of municipal solid and liquid wastes for bioenergy and bioproducts production.

PubMed

Chen, Paul; Xie, Qinglong; Addy, Min; Zhou, Wenguang; Liu, Yuhuan; Wang, Yunpu; Cheng, Yanling; Li, Kun; Ruan, Roger

2016-09-01

Municipal wastes, be it solid or liquid, are rising due to the global population growth and rapid urbanization and industrialization. Conventional management practice involving recycling, combustion, and treatment/disposal is deemed unsustainable. Solutions must be sought to not only increase the capacity but also improve the sustainability of waste management. Research has demonstrated that the non-recyclable waste materials and bio-solids can be converted into useable heat, electricity, or fuel and chemical through a variety of processes, including gasification, pyrolysis, anaerobic digestion, and landfill gas in addition to combustion, and wastewater streams have the potential to support algae growth and provide other energy recovery options. The present review is intended to assess and analyze the current state of knowledge in the municipal solid wastes and wastewater treatment and utilization technologies and recommend practical solution options and future research and development needs. Copyright © 2016 Elsevier Ltd. All rights reserved.

Reprocessable thermosets for sustainable three-dimensional printing.

PubMed

Zhang, Biao; Kowsari, Kavin; Serjouei, Ahmad; Dunn, Martin L; Ge, Qi

2018-05-08

Among all three-dimensional (3D) printing materials, thermosetting photopolymers claim almost half of the market, and have been widely used in various fields owing to their superior mechanical stability at high temperatures, excellent chemical resistance as well as good compatibility with high-resolution 3D printing technologies. However, once these thermosetting photopolymers form 3D parts through photopolymerization, the covalent networks are permanent and cannot be reprocessed, i.e., reshaped, repaired, or recycled. Here, we report a two-step polymerization strategy to develop 3D printing reprocessable thermosets (3DPRTs) that allow users to reform a printed 3D structure into a new arbitrary shape, repair a broken part by simply 3D printing new material on the damaged site, and recycle unwanted printed parts so the material can be reused for other applications. These 3DPRTs provide a practical solution to address environmental challenges associated with the rapid increase in consumption of 3D printing materials.

Evaluating the progress of the UK's Material Recycling Facilities: a mini review.

PubMed

Ali, Muhammad; Courtenay, Peter

2014-12-01

Over the last 15 years, the UK has made great strides in reducing the amount of waste being sent to landfill while also increasing the amount of waste being recycled. The key drivers for this change are the European Union Landfill Directive (1999/31/EC) and the UK Landfill Tax. However, also playing their part are the growing numbers of Material Recycling Facilities (MRFs), which process recyclables. This mini review evaluates the current state of MRFs in the UK, through extensive secondary research, and detailed primary data analysis focussing on MRFs located in South-East England, UK. This study also explores technologies that aim to generate energy from waste, including Waste-to-Energy (WtE) and Refuse-derived Fuel (RDF) facilities. These facilities can have a huge appetite for waste, which can be detrimental to recycling efforts as some of the waste being sent there should be recycled. It was found that the waste sent to a typical UK MRF would recycle around 92% of materials while 6% was sent to energy recovery and the remaining 2% ended up in landfill. Therefore, the total estimated rejected or non-compliance materials from MRFs are around 8%. A key recommendation from this study is to adopt a strategy to combine MRFs with a form of energy generation, such as WtE or RDF. This integrated approach would ensure any residual waste arising from the recycling process can be used as a sustainable fuel, while also increasing the recycling rates. © The Author(s) 2014.

Investigation of Self Consolidating Concrete Containing High Volume of Supplementary Cementitious Materials and Recycled Asphalt Pavement Aggregates

NASA Astrophysics Data System (ADS)

Patibandla, Varun chowdary

The use of sustainable technologies such as supplementary cementitiuous materials (SCMs), and/or recycled materials is expected to positively affect the performance of concrete mixtures. However, it is important to study and qualify such mixtures and check if the required specifications of their intended application are met before they can be implemented in practice. This study presents the results of a laboratory investigation of Self Consolidating concrete (SCC) containing sustainable technologies. A total of twelve concrete mixtures were prepared with various combinations of fly ash, slag, and recycled asphalt pavement (RAP). The mixtures were divided into three groups with constant water to cementitiuous materials ratio of 0.37, and based on the RAP content; 0, 25, and 50% of coarse aggregate replaced by RAP. All mixtures were prepared to achieve a target slump flow equal to or higher than 500 mm (24in). A control mixture for each group was prepared with 100% Portland cement whereas all other mixtures were designed to have up to 70% of portland cement replaced by a combination of supplementary cementitiuous materials (SCMs) such as class C fly ash and granulated blast furnace slag. The properties of fresh concrete investigated in this study include flowability, deformability; filling capacity, and resistance to segregation. In addition, the compressive strength at 3, 14, and 28 days, the tensile strength, and the unrestrained shrinkage up to 80 days was also investigated. As expected the inclusion of the sustainable technologies affected both fresh and hardened concrete properties. Analysis of the experimental data indicated that inclusion of RAP not only reduces the ultimate strength, but it also affected the compressive strength development rate. Moreover, several mixes satisfied compressive strength requirements for pavements and bridges; those mixes included relatively high percentages of SCMs and RAP. Based on the results obtained in this study, it is not recommended to replace the coarse aggregate in SCC by more than 25% RAP.

Linking energy-sanitation-agriculture: Intersectional resource management in smallholder households in Tanzania.

PubMed

Krause, Ariane; Rotter, Vera Susanne

2017-07-15

In order to create sustainable systems for resource management, residues from cooking and ecological sanitation (EcoSan) can be employed in recycling-driven soil fertility management. However, the link between energy, sanitation, and agricultural productivity is often neglected. Hence, the potential self-sufficient nature of many smallholdings in sub-Saharan Africa is underexploited. To compare those cooking and sanitation technologies most commonly used in north-western Tanzania with locally developed alternatives, with respect to (i) resource consumption, (ii) potential to recover resources, and (iii) environmental emissions. This study examines technologies at the household level, and was carried out using material flow analysis (MFA). The specific bioenergy technologies analysed include: three-stone fires; charcoal burners; improved cooking stoves (ICS), such as rocket and microgasifier stoves; and biogas systems. The specific sanitation alternatives studied comprise: pit latrines; two approaches to EcoSan; and septic systems. The use of ICS reduces total resource consumption; using charcoal or biogas does not. The residues from microgasifiers were analysed as having a substantial recovery potential for carbon (C) and phosphorus (P). The fact that input substrates for biogas digesters are post-agricultural in nature means that biogas slurry is not considered an 'untapped resource' despite its ample nutrient content. Exchanging pit latrines for water-based sanitation systems places heavy pressure on already scarce water resources for local smallholders. In contrast, the implementation of waterless EcoSan facilities significantly promotes nutrient recovery and reduces environmental emissions, particularly through greenhouse gas emission and nutrient leaching. Recycled outputs from the triple energy-sanitation-agriculture nexus display complementary benefits: residues from cooking can be used to restore organic matter in soils, while sanitation residues contribute to fertilisation. The combination of microgasifiers and EcoSan-facilities is the most appropriate in order to simultaneously optimise resource consumption, reduce environmental impacts, and maximise recycling-based soil management in smallholder farming systems. Copyright © 2017 Elsevier B.V. All rights reserved.

Informal E-waste recycling in developing countries: review of metal(loid)s pollution, environmental impacts and transport pathways.

PubMed

Ackah, Michael

2017-11-01

Crude or primitive recycling practices are often adopted in material resource recovery from E-waste in developing nations. Significant human health and environmental impacts may occur because of such practices. Literature on metal(loid)s pollution during E-waste processing is fragmented. Here, I review the health and environmental impacts of E-waste recycling operations and transport pathways of metal(loid)s, dispersed during operations. This paper is organised into five sections. Section 1 relates to the background of global E-waste generation and legal/illegal trade, citing specific cases from Ghana and other developing nations. Section 2 provides a brief information on sources of metal(loid)s in E-waste. Section 3 describes characteristics of informal E-waste recycling operations in developing nations. Section 4 examines the health and environmental impacts in E-waste recycling while section 5 evaluates major transport pathways of metal(loid)s contaminants.

Joint investigation of working conditions, environmental and system performance at recycling centres--development of instruments and their usage.

PubMed

Engkvist, I-L; Eklund, J; Krook, J; Björkman, M; Sundin, E; Svensson, R; Eklund, M

2010-05-01

Recycling is a new and developing industry, which has only been researched to a limited extent. This article describes the development and use of instruments for data collection within a multidisciplinary research programme "Recycling centres in Sweden - working conditions, environmental and system performance". The overall purpose of the programme was to form a basis for improving the function of recycling centres with respect to these three perspectives and the disciplines of: ergonomics, safety, external environment, and production systems. A total of 10 instruments were developed for collecting data from employees, managers and visitors at recycling centres, including one instrument for observing visitors. Validation tests were performed in several steps. This, along with the quality of the collected data, and experience from the data collection, showed that the instruments and methodology used were valid and suitable for their purpose. Copyright (c) 2009 Elsevier Ltd. All rights reserved.

Demonstrate a Low Biochemical Oxygen Demand Aircraft Deicing Fluid

DTIC Science & Technology

2013-03-01

Technologies International, LTD for collection and recycling of fluids. Spent fluid, diluted with any water, slush or snow removed from the aircraft or...Resistance Unmated only – some failures Voltage Withstand Testing Unmated only – some failures Plastic Windows Crazing Effect Pass The testing did result...At Joint Base McGuire-Dix-Lakehurst, however, waste PG is currently collected with a vacuum truck and recycled . Factors such as the market demand

Demonstrate a Low Biochemical Oxygen Demand Aircraft Deicing Fluid

DTIC Science & Technology

2013-03-04

Technologies International, LTD for collection and recycling of fluids. Spent fluid, diluted with any water, slush or snow removed from the aircraft or...Resistance Unmated only – some failures Voltage Withstand Testing Unmated only – some failures Plastic Windows Crazing Effect Pass The testing did result...At Joint Base McGuire-Dix-Lakehurst, however, waste PG is currently collected with a vacuum truck and recycled . Factors such as the market demand

Development potential of e-waste recycling industry in China.

PubMed

Li, Jinhui; Yang, Jie; Liu, Lili

2015-06-01

Waste electrical and electronic equipment (WEEE or e-waste) recycling industries in China have been through several phases from spontaneous informal family workshops to qualified enterprises with treatment fund. This study attempts to analyse the development potential of the e-waste recycling industry in China from the perspective of both time and scale potential. An estimation and forecast of e-waste quantities in China shows that, the total e-waste amount reached approximately 5.5 million tonnes in 2013, with 83% of air conditioners, refrigerators, washing machines, televisions sand computers. The total quantity is expected to reach ca. 11.7 million tonnes in 2020 and 20 million tonnes in 2040, which indicates a large increase potential. Moreover, the demand for recycling processing facilities, the optimal service radius of e-waste recycling enterprises and estimation of the profitability potential of the e-waste recycling industry were analysed. Results show that, based on the e-waste collection demand, e-waste recycling enterprises therefore have a huge development potential in terms of both quantity and processing capacity, with 144 and 167 e-waste recycling facilities needed, respectively, by 2020 and 2040. In the case that e-waste recycling enterprises set up their own collection points to reduce the collection cost, the optimal collection service radius is estimated to be in the range of 173 km to 239 km. With an e-waste treatment fund subsidy, the e-waste recycling industry has a small economic profit, for example ca. US$2.5/unit for television. The annual profit for the e-waste recycling industry overall was about 90 million dollars in 2013. © The Author(s) 2015.

Data summary of municipal solid waste management alternatives. Volume 12, Numerically indexed bibliography

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1992-10-01

This appendix contains the numerically indexed bibliography for the complete group of reports on municipal solid waste management alternatives. The list references information on the following topics: mass burn technologies, RDF technologies, fluidized bed combustion, pyrolysis and gasification of MSW, materials recovery- recycling technologies, sanitary landfills, composting and anaerobic digestion of MSW.

Data summary of municipal solid waste management alternatives. Volume 11, Alphabetically indexed bibliography

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1992-10-01

This appendix contains the alphabetically indexed bibliography for the complete group of reports on municipal waste management alternatives. The references are listed for each of the following topics: mass burn technologies, RDF technologies, fluidized-bed combustion, pyrolysis and gasification of MSW, materials recovery- recycling technologies, sanitary landfills, composting, and anaerobic digestion of MSW.

Technology development of the Space Transportation System mission and terrestrial applications of satellite technology

NASA Technical Reports Server (NTRS)

1981-01-01

The Space Transportation System (STS) is discussed, including the launch processing system, the thermal protection subsystem, meteorological research, sound supression water system, rotating service structure, improved hypergol or removal systems, fiber optics research, precision positioning, remote controlled solid rocket booster nozzle plugs, ground operations for Centaur orbital transfer vehicle, parachute drying, STS hazardous waste disposal and recycle, toxic waste technology and control concepts, fast analytical densitometry study, shuttle inventory management system, operational intercommunications system improvement, and protective garment ensemble. Terrestrial applications are also covered, including LANDSAT applications to water resources, satellite freeze forecast system, application of ground penetrating radar to soil survey, turtle tracking, evaluating computer drawn ground cover maps, sparkless load pulsar, and coupling a microcomputer and computing integrator with a gas chromatograph.

"This is public health: recycling counts!" Description of a pilot health communications campaign.

PubMed

L Chase, Nancy; Dominick, Gregory M; Trepal, Amy; Bailey, Leanne S; Friedman, Daniela B

2009-12-01

This paper describes the development, implementation, and evaluation of a pilot recycling campaign. The goal of the campaign was to increase people's awareness and knowledge about recycling and the link between a healthy environment and the public's health. A total of 258 individuals attended campaign week events and completed an initial survey. Results identified inconvenience of recycling facility locations as a key barrier to recycling. Post-campaign survey results revealed increased recycling of paper, plastic, glass, and cans (p < 0.05). The majority of participants "agreed" or "strongly agreed" that as a result of campaign messages they had greater awareness about recycling (88.4%) and their recycling efforts increased (61.6%).

Critical evaluation and thermodynamic optimization of the Iron-Rare-Earth systems

NASA Astrophysics Data System (ADS)

Konar, Bikram

Rare-Earth elements by virtue of its typical magnetic, electronic and chemical properties are gaining importance in power, electronics, telecommunications and sustainable green technology related industries. The Magnets from RE-alloys are more powerful than conventional magnets which have more longevity and high temperature workability. The dis-equilibrium in the Rare-Earth element supply and demand has increased the importance of recycling and extraction of REE's from used permanent Magnets. However, lack of the thermodynamic data on RE alloys has made it difficult to design an effective extraction and recycling process. In this regard, Computational Thermodynamic calculations can serve as a cost effective and less time consuming tool to design a waste magnet recycling process. The most common RE permanent magnet is Nd magnet (Nd 2Fe14B). Various elements such as Dy, Tb, Pr, Cu, Co, Ni, etc. are also added to increase its magnetic and mechanical properties. In order to perform reliable thermodynamic calculations for the RE recycling process, accurate thermodynamic database for RE and related alloys are required. The thermodynamic database can be developed using the so-called CALPHAD method. The database development based on the CALPHAD method is essentially the critical evaluation and optimization of all available thermodynamic and phase diagram data. As a results, one set of self-consistent thermodynamic functions for all phases in the given system can be obtained, which can reproduce all reliable thermodynamic and phase diagram data. The database containing the optimized Gibbs energy functions can be used to calculate complex chemical reactions for any high temperature processes. Typically a Gibbs energy minimization routine, such as in FactSage software, can be used to obtain the accurate thermodynamic equilibrium in multicomponent systems. As part of a large thermodynamic database development for permanent magnet recycling and Mg alloy design, all thermodynamic and phase diagram data in the literature for the fourteen Fe-RE binary systems: Fe-La, Fe-Ce, Fe-Pr, Fe-Nd, Fe-Sm, Fe-Gd, Fe-Tb, Fe-Dy, Fe-Ho, Fe-Er, Fe-Tm, Fe-Lu, Fe-Sc and Fe-Y are critically evaluated and optimized to obtain thermodynamic model parameters. The model parameters can be used to calculate phase diagrams and Gibbs energies of all phases as functions of temperature and composition. This database can be incorporated with the present thermodynamic database in FactSage software to perform complex chemical reactions and phase diagram calculations for RE magnet recycling process.

Prioritized List of Research Needs to support MRWFD Case Study Flowsheet Advancement

DOE Office of Scientific and Technical Information (OSTI.GOV)

Law, Jack Douglas; Soelberg, Nicholas Ray

In FY-13, a case study evaluation was performed of full recycle technologies for both the processing of light-water reactor (LWR) used nuclear fuels as well as fast reactor (FR) fuel in the full recycle option. This effort focused on the identification of the case study processes and the initial preparation of material balance flowsheets for the identified technologies. In identifying the case study flowsheets, it was decided that two cases would be developed: one which identifies the flowsheet as currently developed and another near-term target flowsheet which identifies the flowsheet as envisioned within two years, pending the results of ongoingmore » research. The case study focus is on homogeneous aqueous recycle of the U/TRU resulting from the processing of LWR fuel as feed for metal fuel fabrication. The metal fuel is utilized in a sodium-cooled fast reactor, and the used fast reactor fuel is processed using electrochemical separations. The recovered U/TRU from electrochemical separations is recycled to fuel fabrication and the fast reactor. Waste streams from the aqueous and electrochemical processing are treated and prepared for disposition. Off-gas from the separations and waste processing are also treated. As part of the FY-13 effort, preliminary process unknowns and research needs to advance the near-term target flowsheets were identified. In FY-14, these research needs were updated, expanded and prioritized. This report again updates the prioritized list of research needs based upon results to date in FY-15. The research needs are listed for each of the main portions of the flowsheet: 1) Aqueous headend, 2) Headend tritium pretreatment off-gas, 3) Aqueous U/Pu/Np recovery, 4) Aqueous TRU product solidification, 5) Aqueous actinide/lanthanide separation, 6) Aqueous off-gas treatment, 7) Aqueous HLW management, 8) Treatment of aqueous process wastes, 9) E-chem actinide separations, 10) E-chem off-gas, 11) E-chem HLW management. The identified research needs were prioritized within each of these areas. No effort was made to perform an overall prioritization. This information will be used by the MRWFD Campaign leadership in research planning for FY-16. Additionally, this information will be incorporated into the next version of the Case Study Report scheduled to be issued September 2015.« less

Nutrient and media recycling in heterotrophic microalgae cultures.

PubMed

Lowrey, Joshua; Armenta, Roberto E; Brooks, Marianne S

2016-02-01

In order for microalgae-based processes to reach commercial production for biofuels and high-value products such as omega-3 fatty acids, it is necessary that economic feasibility be demonstrated at the industrial scale. Therefore, process optimization is critical to ensure that the maximum yield can be achieved from the most efficient use of resources. This is particularly true for processes involving heterotrophic microalgae, which have not been studied as extensively as phototrophic microalgae. An area that has received significant conceptual praise, but little experimental validation, is that of nutrient recycling, where the waste materials from prior cultures and post-lipid extraction are reused for secondary fermentations. While the concept is very simple and could result in significant economic and environmental benefits, there are some underlying challenges that must be overcome before adoption of nutrient recycling is viable at commercial scale. Even more, adapting nutrient recycling for optimized heterotrophic cultures presents some added challenges that must be identified and addressed that have been largely unexplored to date. These challenges center on carbon and nitrogen recycling and the implications of using waste materials in conjunction with virgin nutrients for secondary cultures. The aim of this review is to provide a foundation for further understanding of nutrient recycling for microalgae cultivation. As such, we outline the current state of technology and practical challenges associated with nutrient recycling for heterotrophic microalgae on an industrial scale and give recommendations for future work.

Solid waste management in Asian countries: a review of solid waste minimisation (3'r) towards low carbon

NASA Astrophysics Data System (ADS)

Ali, N. E.; Sion, H. C.

2014-02-01

The amount of solid-waste generated in Asian countries has increased tremendously, mainly due to the improvement in living standards, rapid developments in technology, growth in economy and population in the cities. Solid waste management is a global issue and major challenge facing Asian countries and neglecting its management may have negative consequences on the environment. Waste composition data proves the developed countries to have generated more recyclable materials while developing countries produce more organic and less recyclable waste such as paper, plastic and aluminium. In this regard, increase in number of landfills and disposal sites, will have an impact on GHG (greenhouse gas) emissions and pollutants to air and water. Alternative methods should therefore be taken to reduce the volume of waste. Most Asian countries have adopted the 3R (reduce, reuse, recycle) concept in order to reduce solid waste and their governments have implemented laws and regulations in order to support this. Implementation of 3R is the major contributor to the solid waste minimization and it can improve the quality of environmental sustainability and reduction of carbon dioxide emission in to the atmosphere. Based on our review, most of the countries practicing the 3R concept in tandem with laws and regulations perform better than those that just practice the 3R concept without any laws and regulations. The paper suggests that every country must focus on the laws and regulations relating to solid waste minimization so that it could be easily implemented as outlined.

Sustainable mechanical biological treatment of solid waste in urbanized areas with low recycling rates.

PubMed

Trulli, Ettore; Ferronato, Navarro; Torretta, Vincenzo; Piscitelli, Massimiliano; Masi, Salvatore; Mancini, Ignazio

2018-01-01

Landfill is still the main technological facility used to treat and dispose municipal solid waste (MSW) worldwide. In developing countries, final dumping is applied without environmental monitoring and soil protection since solid waste is mostly sent to open dump sites while, in Europe, landfilling is considered as the last option since reverse logistic approaches or energy recovery are generally encouraged. However, many regions within the European Union continue to dispose of MSW to landfill, since modern facilities have not been introduced owing to unreliable regulations or financial sustainability. In this paper, final disposal activities and pre-treatment operations in an area in southern Italy are discussed, where final disposal is still the main option for treating MSW and the recycling rate is still low. Mechanical biological treatment (MBT) facilities are examined in order to evaluate the organic stabilization practices applied for MSW and the efficiencies in refuse derived fuel production, organic waste stabilization and mass reduction. Implementing MBT before landfilling the environmental impact and waste mass are reduced, up to 30%, since organic fractions are stabilized resulting an oxygen uptake rate less than 1600 mgO 2  h -1  kg -1 VS , and inorganic materials are exploited. Based on experimental data, this work examines MBT application in contexts where recycling and recovery activities have not been fully developed. The evidence of this study led to state that the introduction of MBT facilities is recommended for developing regions with high putrescible waste production in order to decrease environmental pollution and enhance human healthy. Copyright © 2017 Elsevier Ltd. All rights reserved.

Current status of solid waste management in small island developing states: A review.

PubMed

Mohee, Romeela; Mauthoor, Sumayya; Bundhoo, Zumar M A; Somaroo, Geeta; Soobhany, Nuhaa; Gunasee, Sanjana

2015-09-01

This article reviews the current status of waste management in Small Island Developing States (SIDS) and the challenges that are faced in solid waste management. The waste generation rates of SIDS were compared within the three geographic regions namely Caribbean SIDS, Pacific SIDS and Atlantic, Indian Ocean, Mediterranean and South China (AIMS) SIDS and with countries of the Organisation for Economic Co-Operation and Development (OECD). Only Pacific SIDS had a waste generation rate less than 1kg/capita/day. The waste generation rates for the three SIDS regions averaged 1.29kg/capita/day while that for OECD countries was at a mean value of 1.35kg/capita/day. The waste compositions in the different SIDS regions were almost similar owing to comparable consumption patterns while these differed to a large extent with wastes generated in OECD countries. In SIDS, the major fraction of MSW comprised of organics (44%) followed by recyclables namely paper, plastics, glass and metals (total: 43%). In contrast, MSW in OECD countries consisted mainly of recyclables (43%) followed by organics (37%). This article also reviewed the other functional elements of the waste management systems in SIDS. Several shortcomings were noted in the process of waste collection, transfer and transport namely the fact of having outdated collection vehicles and narrow roads which are inaccessible. Among the waste management practices in SIDS, waste disposal via landfilling, illegal dumping and backyard burning were favoured most of the time at the expense of sustainable waste treatment technologies such as composting, anaerobic digestion and recycling. Copyright © 2015 Elsevier Ltd. All rights reserved.

Development and Validation of an Instrument for Assessing Attitudes of High School Students about Recycling

ERIC Educational Resources Information Center

Ugulu, Ilker

2015-01-01

Recycling and its applications are growing significantly due to the great potential for solving a range of environmental problems in society. Nevertheless, there are currently very few instruments that can provide valid and reliable data on students' attitudes toward recycling. In this regard, this article focuses on the development and validation…

Strategic Research Directions in Microgravity Materials Science

NASA Technical Reports Server (NTRS)

Clinton, Raymond G.; Semmes, Ed; Cook, Beth; Wargo, Michael J.; Marzwell, Neville

2003-01-01

The next challenge of space exploration is the development of the capabilities for long-term missions beyond low earth orbit. NASA s scientific advisory groups and internal mission studies have identified several fundamental issues which require substantial advancements in new technology if these goals are to be accomplished. Crews must be protected from the severe radiation environment beyond the earth s magnetic field. Chemical propulsion must be replaced by systems that require less mass and are more efficient. The overall launch complement must be reduced by developing repair and fabrication techniques which utilize or recycle available materials.

Managing critical materials with a technology-specific stocks and flows model.

PubMed

Busch, Jonathan; Steinberger, Julia K; Dawson, David A; Purnell, Phil; Roelich, Katy

2014-01-21

The transition to low carbon infrastructure systems required to meet climate change mitigation targets will involve an unprecedented roll-out of technologies reliant upon materials not previously widespread in infrastructure. Many of these materials (including lithium and rare earth metals) are at risk of supply disruption. To ensure the future sustainability and resilience of infrastructure, circular economy policies must be crafted to manage these critical materials effectively. These policies can only be effective if supported by an understanding of the material demands of infrastructure transition and what reuse and recycling options are possible given the future availability of end-of-life stocks. This Article presents a novel, enhanced stocks and flows model for the dynamic assessment of material demands resulting from infrastructure transitions. By including a hierarchical, nested description of infrastructure technologies, their components, and the materials they contain, this model can be used to quantify the effectiveness of recovery at both a technology remanufacturing and reuse level and a material recycling level. The model's potential is demonstrated on a case study on the roll-out of electric vehicles in the UK forecast by UK Department of Energy and Climate Change scenarios. The results suggest policy action should be taken to ensure Li-ion battery recycling infrastructure is in place by 2025 and NdFeB motor magnets should be designed for reuse. This could result in a reduction in primary demand for lithium of 40% and neodymium of 70%.

Managing Critical Materials with a Technology-Specific Stocks and Flows Model

PubMed Central

2013-01-01

The transition to low carbon infrastructure systems required to meet climate change mitigation targets will involve an unprecedented roll-out of technologies reliant upon materials not previously widespread in infrastructure. Many of these materials (including lithium and rare earth metals) are at risk of supply disruption. To ensure the future sustainability and resilience of infrastructure, circular economy policies must be crafted to manage these critical materials effectively. These policies can only be effective if supported by an understanding of the material demands of infrastructure transition and what reuse and recycling options are possible given the future availability of end-of-life stocks. This Article presents a novel, enhanced stocks and flows model for the dynamic assessment of material demands resulting from infrastructure transitions. By including a hierarchical, nested description of infrastructure technologies, their components, and the materials they contain, this model can be used to quantify the effectiveness of recovery at both a technology remanufacturing and reuse level and a material recycling level. The model’s potential is demonstrated on a case study on the roll-out of electric vehicles in the UK forecast by UK Department of Energy and Climate Change scenarios. The results suggest policy action should be taken to ensure Li-ion battery recycling infrastructure is in place by 2025 and NdFeB motor magnets should be designed for reuse. This could result in a reduction in primary demand for lithium of 40% and neodymium of 70%. PMID:24328245

Life cycle assessment of electronic waste treatment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hong, Jinglan, E-mail: hongjing@sdu.edu.cn; Shandong University Climate Change and Health Center, Public Health School, Shandong University, Jinan 250012; Shi, Wenxiao

Highlights: • Life cycle assessment of electronic waste recycling is quantified. • Key factors for reducing the overall environmental impact are indentified. • End-life disposal processes provide significant environmental benefits. • Efficiently reduce the improper disposal amount of e-waste is highly needed. • E-waste incineration can generate significant environmental burden. - Abstract: Life cycle assessment was conducted to estimate the environmental impact of electronic waste (e-waste) treatment. E-waste recycling with an end-life disposal scenario is environmentally beneficial because of the low environmental burden generated from human toxicity, terrestrial ecotoxicity, freshwater ecotoxicity, and marine ecotoxicity categories. Landfill and incineration technologies havemore » a lower and higher environmental burden than the e-waste recycling with an end-life disposal scenario, respectively. The key factors in reducing the overall environmental impact of e-waste recycling are optimizing energy consumption efficiency, reducing wastewater and solid waste effluent, increasing proper e-waste treatment amount, avoiding e-waste disposal to landfill and incineration sites, and clearly defining the duties of all stakeholders (e.g., manufacturers, retailers, recycling companies, and consumers)« less

Battery resource assessment. Subtask 2.5: Battery manufacturing capability recycling of battery materials

NASA Astrophysics Data System (ADS)

Pemsler, P.

1981-02-01

Studies were conducted on the recycling of advanced battery system components for six different battery systems. These include: nickel/zinc, nickel/iron, zinc/chlorine, zinc/bromine, sodium/sulfur, and lithium-aluminum/iron sulfide. For each battery system, one or more processes were developed which would permit recycling of the major or active materials. Each recycle process was designed to produce a product material which can be used directly as a raw material by the battery manufacturer. Metal recoverabilities are in the range of 93 to 95% for all processes. In each case, capital and operating costs were developed for a recycling plant which processes 100,000 electric vehicle batteries per year.

76 FR 18217 - Environmental Impacts Statements; Notice of Availability

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-01

.... 20110089, Draft EIS, HUD, CA, West Coast Recycling Group Metal Recycling Facility Project, Proposal to Develop and Operate a Scrap Metal Shredding and Recycling Facility at the Port of West Sacramento, Yolo...

Biodigester Feasibility and Design for Space & Earth

NASA Technical Reports Server (NTRS)

Shutts, Stacy; Ewert, Mike; Bacon, Jack

2016-01-01

Anaerobic digestion converts organic waste into methane gas and fertilizer effluent. The ICA-developed prototype system is designed for planetary surface operation. It uses passive hydrostatic control for reliability, and is modular and redundant. The serpentine configuration accommodates tight geometric constraints similar to the ISS ECLSS rack architectures. Its shallow, low-tilt design enables (variable) lower-g convection than standard Earth (1 g) digesters. This technology will reuse and recycle materials including human waste, excess food, as well as packaging (if biodegradable bags are used).

A Low Cost Environmentally Benign Waste Lubricants Recycling/Re-refining Technology.

DTIC Science & Technology

1999-05-01

EXPERIMENTAL 3 2.1 Ceramic Membrane Ultrafiltration Pilot Unit 3 2.2 Polishing/Finishing Pilot Unit 3 2.3 Feed Samples 3 2.4 Sample...development of an additional 2 to 3 sites in the US. 2. EXPERIMENTAL 2.1. Ceramic Membrane Ultrafiltration Pilot Unit A photograph of the pilot...scale ceramic membrane system used in this work is shown in Figure la. Samples of spent turbine oil were charged to the feed tank and heated to 150°C

Direct molding of pavement tiles made of ground tire rubber

NASA Astrophysics Data System (ADS)

Quadrini, Fabrizio; Gagliardi, Donatella; Tedde, Giovanni Matteo; Santo, Loredana; Musacchi, Ettore

2016-10-01

Large rubber products can be molded by using only ground tire rubber (GTR) without any additive or binder due to a new technology called "direct molding". Rubber granules and powders from tire recycling are compression molded at elevated temperatures and pressures. The feasibility of this process was clearly shown in laboratory but the step to the industrial scale was missing. Thanks to an European Project (SMART "Sustainable Molding of Articles from Recycled Tires") this step has been made and some results are reported in this study. The press used for compression molding is described. Some tests were made to measure the energy consumption so as to evaluate costs for production in comparison with conventional technologies for GTR molding (by using binders). Results show that 1 m2 tiles can be easily molded with several thicknesses in a reasonable low time. Energy consumption is higher than conventional technologies but it is lower than the cost for binders.

State of the art: wastewater management in the beverage industry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Joyce, M.E.; Scaief, J.F.; Cochrane, M.W.

The water pollution impact caused by the wastes from the beverage industry and the methods available to combat the associated problems were studied. The size of each industry is discussed along with production processes, wastewater sources and effluent characteristics. Wastewater management techniques are described in terms of in-plant recycling, by-product recovery and end-of-pipe treatment along with the economics of treatment. The malt liquor, malting, soft drinks and flavoring industries primarily dispose of their effluents in municipal sewers. In-plant recycling and by-product recovery techniques have been developed in these industries to reduce their raw waste load. The wine and brandy andmore » distilled spirits industries in many cases must treat their own effluents so they have developed wastewater management systems including industry-owned treatment plants that yield good effluents. The technology to adequately treat rum distillery wastewater has not been demonstrated. The information basis for this study was a literature search, an effluent guidelines report done for EPA, limited site visits, personal communications and an unpublished report conducted for EPA that included questionaire surveys of the industries.« less

GATE Center of Excellence at UAB in Lightweight Materials for Automotive Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2011-07-31

This report summarizes the accomplishments of the UAB GATE Center of Excellence in Lightweight Materials for Automotive Applications. The first Phase of the UAB DOE GATE center spanned the period 2005-2011. The UAB GATE goals coordinated with the overall goals of DOE's FreedomCAR and Vehicles Technologies initiative and DOE GATE program. The FCVT goals are: (1) Development and validation of advanced materials and manufacturing technologies to significantly reduce automotive vehicle body and chassis weight without compromising other attributes such as safety, performance, recyclability, and cost; (2) To provide a new generation of engineers and scientists with knowledge and skills inmore » advanced automotive technologies. The UAB GATE focused on both the FCVT and GATE goals in the following manner: (1) Train and produce graduates in lightweight automotive materials technologies; (2) Structure the engineering curricula to produce specialists in the automotive area; (3) Leverage automotive related industry in the State of Alabama; (4) Expose minority students to advanced technologies early in their career; (5) Develop innovative virtual classroom capabilities tied to real manufacturing operations; and (6) Integrate synergistic, multi-departmental activities to produce new product and manufacturing technologies for more damage tolerant, cost-effective, and lighter automotive structures.« less

Solvent-Free Toner Printing of Organic Semiconductor Layer in Flexible Thin-Film Transistors

NASA Astrophysics Data System (ADS)

Sakai, Masatoshi; Koh, Tokuyuki; Toyoshima, Kenji; Nakamori, Kouta; Okada, Yugo; Yamauchi, Hiroshi; Sadamitsu, Yuichi; Shinamura, Shoji; Kudo, Kazuhiro

2017-07-01

A solvent-free printing process for printed electronics is successfully developed using toner-type patterning of organic semiconductor toner particles and the subsequent thin-film formation. These processes use the same principle as that used for laser printing. The organic thin-film transistors are prepared by electrically distributing the charged toner onto a Au electrode on a substrate film, followed by thermal lamination. The thermal lamination is effective for obtaining an oriented and crystalline thin film. Toner printing is environmentally friendly compared with other printing technologies because it is solvent free, saves materials, and enables easy recycling. In addition, this technology simultaneously enables both wide-area and high-resolution printing.

The role of water in unconventional in situ energy resource extraction technologies: Chapter 7 in Food, energy, and water: The chemistry connection

USGS Publications Warehouse

Gallegos, Tanya J.; Bern, Carleton R.; Birdwell, Justin E.; Haines, Seth S.; Engle, Mark A.

2015-01-01

Global trends toward developing new energy resources from lower grade, larger tonnage deposits that are not generally accessible using “conventional” extraction methods involve variations of subsurface in situ extraction techniques including in situ oil-shale retorting, hydraulic fracturing of petroleum reservoirs, and in situ recovery (ISR) of uranium. Although these methods are economically feasible and perhaps result in a smaller above-ground land-use footprint, there remain uncertainties regarding potential subsurface impacts to groundwater. This chapter provides an overview of the role of water in these technologies and the opportunities and challenges for water reuse and recycling.

SITE TECHNOLOGY CAPSULE: IN SITU STEAM ENHANCED RECOVERY PROCESS

EPA Science Inventory

The SERP technology is designed to treat soils contaminated with VOCs and SVOCs in situ. Steam injection and vacuum extraction are used to remove the organic compounds from the soil and concentrate them for disposal or recycling. A full-scale demonstration of SERP was conducted a...

EMERGING TECHNOLOGY BULLETIN: RECLAMATION OF LEAD FROM SUPERFUND WASTE MATERIAL USING SECONDARY LEAD SMELTERS

EPA Science Inventory

This process involves incorporating lead-contaminated Superfund waste with the regular feed to a secondary lead smelter. Since secondary lead smelters already recover lead from recycled automobile batteries, it seems likely that this technology could be used to treat waste from ...

Some challenges in designing a lunar, Martian, or microgravity CELSS.

PubMed

Salisbury, F B

1992-01-01

The design of a bioregenerative life-support system (a Controlled Ecological Life-Support System or CELSS) for long-duration stays on the moon, Mars, or in a space craft poses formidable problems in engineering and in theory. Technological (hardware) problems include: (1) Creation and control of gas composition and pressure, temperature, light, humidity, and air circulation, especially in microgravity to 1/3 xg and in the vacuum of space. Light (energy demanding), CO2 levels, and the rooting media are special problems for plants. (2) Developing specialized equipment for food preparation. (3) Equipment development for waste recycling. (4) Development of computer systems for environmental monitoring and control as well as several other functions. Problems of theory (software) include: (1) Determining crop species and cultivars (some bred especially for CELSS). (2) Optimum environments and growing and harvesting techniques for each crop. (3) Best and most efficient food-preparation techniques and required equipment. (4) Best and most efficient waste-recycling techniques and equipment. This topic includes questions about the extent of closure, resupply, and waste storage. (5) How to achieve long-term stability. (6) How to avoid catastrophic failures--and how to recover from near-catastrophic failures (for example, plant diseases). Many problems must be solved.

Materials for a new generation of vehicles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grobstein, T.

1995-12-31

The Partnership for a New Generation of Vehicles (PNGV) is a national initiative with three goals: first, to significantly improve national competitiveness in manufacturing; second, to implement commercially viable innovations from ongoing research on conventional vehicles, and third, to develop a vehicle to achieve up to three times the fuel efficiency of today`s comparable vehicle (i.e., the 1994 Chrysler Concorde, Ford Taurus, and Chevrolet Lumina). Note this vehicle will have the equivalent customer purchase price of today`s vehicles adjusted for economics, while meeting the customers` needs for quality, performance, and utility. Eight federal agencies are currently contributing to these goals,more » as well as the three principal US automobile manufacturers, numerous automotive component suppliers, research laboratories, and universities. Materials research and development is a significant effort within PNGV. The goals in this area include development of lightweight, recyclable materials for structural applications, high strength, long-life, high temperature materials for engine components, improved materials for alternative propulsion and energy storage systems, and cost-effective process technologies and component fabrication methods. Application of advanced materials to automobiles will involve consideration of diverse factors, including weight savings, affordability, recyclability, crashworthiness, repairability, and manufacturability.« less

Some challenges in designing a lunar, Martian, or microgravity CELSS

NASA Astrophysics Data System (ADS)

Salisbury, Frank B.

The design of a bioregenerative life-support system (a Controlled Ecological Life-Support System or CELSS) for long-duration stays on the moon, Mars, or in a space craft poses formidable problems in engineering and in theory. Technological (hardware) problems include: (1) Creation and control of gas composition and pressure, temperature, light, humidity, and air circulation, especially in microgravity to 1/3xg and in the vacuum of space. Light (energy demanding), CO 2 levels, and the rooting media are special problems for plants. (2) Developing specialized equipment for food preparation. (3) Equipment development for waste recycling. (4) Development of computer systems for environmental monitoring and control as well as several other functions. Problems of theory (software) include: (1) Determining crop species and cultivars (some bred especially for CELSS). (2) Optimum environments and growing and harvesting techniques for each crop. (3) Best and most efficient food-preparation techniques and required equipment. (4) Best and most efficient waste-recycling techniques and equipment. This topic includes questions about the extent of closure, resupply, and waste storage. (5) How to achieve long-term stability. (6) How to avoid catastrophic failures-and how to recover from near-catastrophic failures (for example, plant diseases). Many problems must be solved.

Spatial optimization for decentralized non-potable water reuse

NASA Astrophysics Data System (ADS)

Kavvada, Olga; Nelson, Kara L.; Horvath, Arpad

2018-06-01

Decentralization has the potential to reduce the scale of the piped distribution network needed to enable non-potable water reuse (NPR) in urban areas by producing recycled water closer to its point of use. However, tradeoffs exist between the economies of scale of treatment facilities and the size of the conveyance infrastructure, including energy for upgradient distribution of recycled water. To adequately capture the impacts from distribution pipes and pumping requirements, site-specific conditions must be accounted for. In this study, a generalized framework (a heuristic modeling approach using geospatial algorithms) is developed that estimates the financial cost, the energy use, and the greenhouse gas emissions associated with NPR (for toilet flushing) as a function of scale of treatment and conveyance networks with the goal of determining the optimal degree of decentralization. A decision-support platform is developed to assess and visualize NPR system designs considering topography, economies of scale, and building size. The platform can be used for scenario development to explore the optimal system size based on the layout of current or new buildings. The model also promotes technology innovation by facilitating the systems-level comparison of options to lower costs, improve energy efficiency, and lower greenhouse gas emissions.

“This Is Public Health: Recycling Counts!” Description of a Pilot Health Communications Campaign

PubMed Central

L.Chase, Nancy; Dominick, Gregory M.; Trepal, Amy; Bailey, Leanne S.; Friedman, Daniela B.

2009-01-01

This paper describes the development, implementation, and evaluation of a pilot recycling campaign. The goal of the campaign was to increase people’s awareness and knowledge about recycling and the link between a healthy environment and the public’s health. A total of 258 individuals attended campaign week events and completed an initial survey. Results identified inconvenience of recycling facility locations as a key barrier to recycling. Post-campaign survey results revealed increased recycling of paper, plastic, glass, and cans (p < 0.05). The majority of participants “agreed” or “strongly agreed” that as a result of campaign messages they had greater awareness about recycling (88.4%) and their recycling efforts increased (61.6%). PMID:20049239

Environmentally-friendly oxygen-free roasting/wet magnetic separation technology for in situ recycling cobalt, lithium carbonate and graphite from spent LiCoO2/graphite lithium batteries.

PubMed

Li, Jia; Wang, Guangxu; Xu, Zhenming

2016-01-25

The definite aim of the present paper is to present some novel methods that use oxygen-free roasting and wet magnetic separation to in situ recycle of cobalt, Lithium Carbonate and Graphite from mixed electrode materials. The in situ recycling means to change waste into resources by its own components, which is an idea of "waste+waste→resources." After mechanical scraping the mixed electrode materials enrich powders of LiCoO2 and graphite. The possible reaction between LiCoO2 and graphite was obtained by thermodynamic analysis. The feasibility of the reaction at high temperature was studied with the simultaneous thermogravimetry analysis under standard atmospheric pressure. Then the oxygen-free roasting/wet magnetic separation method was used to transfer the low added value mixed electrode materials to high added value products. The results indicated that, through the serious technologies of oxygen-free roasting and wet magnetic separation, mixture materials consist with LiCoO2 and graphite powders are transferred to the individual products of cobalt, Lithium Carbonate and Graphite. Because there is not any chemical solution added in the process, the cost of treating secondary pollution can be saved. This study provides a theoretical basis for industrial-scale recycling resources from spent LIBs. Copyright © 2015 Elsevier B.V. All rights reserved.

75 FR 67391 - Notice of Intent To Prepare a Draft Environmental Impact Statement for the West Coast Recycling...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-02

... a Draft Environmental Impact Statement for the West Coast Recycling Group Project in West Sacramento... (EIS/EIR) for the development of the West Coast Recycling Group project located at the Port of West... meeting date. SUPPLEMENTARY INFORMATION: Description of the Proposed Action The West Coast Recycling Group...