Investigation on the Practicality of Developing Reduced Thermal Models

NASA Technical Reports Server (NTRS)

Lombardi, Giancarlo; Yang, Kan

2015-01-01

Throughout the spacecraft design and development process, detailed instrument thermal models are created to simulate their on-orbit behavior and to ensure that they do not exceed any thermal limits. These detailed models, while generating highly accurate predictions, can sometimes lead to long simulation run times, especially when integrated with a spacecraft observatory model. Therefore, reduced models containing less detail are typically produced in tandem with the detailed models so that results may be more readily available, albeit less accurate. In the current study, both reduced and detailed instrument models are integrated with their associated spacecraft bus models to examine the impact of instrument model reduction on run time and accuracy. Preexisting instrument bus thermal model pairs from several projects were used to determine trends between detailed and reduced thermal models; namely, the Mirror Optical Bench (MOB) on the Gravity and Extreme Magnetism Small Explorer (GEMS) spacecraft, Advanced Topography Laser Altimeter System (ATLAS) on the Ice, Cloud, and Elevation Satellite 2 (ICESat-2), and the Neutral Mass Spectrometer (NMS) on the Lunar Atmosphere and Dust Environment Explorer (LADEE). Hot and cold cases were run for each model to capture the behavior of the models at both thermal extremes. It was found that, though decreasing the number of nodes from a detailed to reduced model brought about a reduction in the run-time, a large time savings was not observed, nor was it a linear relationship between the percentage of nodes reduced and time saved. However, significant losses in accuracy were observed with greater model reduction. It was found that while reduced models are useful in decreasing run time, there exists a threshold of reduction where, once exceeded, the loss in accuracy outweighs the benefit from reduced model runtime.

POD/DEIM reduced-order strategies for efficient four dimensional variational data assimilation

NASA Astrophysics Data System (ADS)

Ştefănescu, R.; Sandu, A.; Navon, I. M.

2015-08-01

This work studies reduced order modeling (ROM) approaches to speed up the solution of variational data assimilation problems with large scale nonlinear dynamical models. It is shown that a key requirement for a successful reduced order solution is that reduced order Karush-Kuhn-Tucker conditions accurately represent their full order counterparts. In particular, accurate reduced order approximations are needed for the forward and adjoint dynamical models, as well as for the reduced gradient. New strategies to construct reduced order based are developed for proper orthogonal decomposition (POD) ROM data assimilation using both Galerkin and Petrov-Galerkin projections. For the first time POD, tensorial POD, and discrete empirical interpolation method (DEIM) are employed to develop reduced data assimilation systems for a geophysical flow model, namely, the two dimensional shallow water equations. Numerical experiments confirm the theoretical framework for Galerkin projection. In the case of Petrov-Galerkin projection, stabilization strategies must be considered for the reduced order models. The new reduced order shallow water data assimilation system provides analyses similar to those produced by the full resolution data assimilation system in one tenth of the computational time.

Use of operating room information system data to predict the impact of reducing turnover times on staffing costs.

PubMed

Dexter, Franklin; Abouleish, Amr E; Epstein, Richard H; Whitten, Charles W; Lubarsky, David A

2003-10-01

Potential benefits to reducing turnover times are both quantitative (e.g., complete more cases and reduce staffing costs) and qualitative (e.g., improve professional satisfaction). Analyses have shown the quantitative arguments to be unsound except for reducing staffing costs. We describe a methodology by which each surgical suite can use its own numbers to calculate its individual potential reduction in staffing costs from reducing its turnover times. Calculations estimate optimal allocated operating room (OR) time (based on maximizing OR efficiency) before and after reducing the maximum and average turnover times. At four academic tertiary hospitals, reductions in average turnover times of 3 to 9 min would result in 0.8% to 1.8% reductions in staffing cost. Reductions in average turnover times of 10 to 19 min would result in 2.5% to 4.0% reductions in staffing costs. These reductions in staffing cost are achieved predominantly by reducing allocated OR time, not by reducing the hours that staff work late. Heads of anesthesiology groups often serve on OR committees that are fixated on turnover times. Rather than having to argue based on scientific studies, this methodology provides the ability to show the specific quantitative effects (small decreases in staffing costs and allocated OR time) of reducing turnover time using a surgical suite's own data. Many anesthesiologists work at hospitals where surgeons and/or operating room (OR) committees focus repeatedly on turnover time reduction. We developed a methodology by which the reductions in staffing cost as a result of turnover time reduction can be calculated for each facility using its own data. Staffing cost reductions are generally very small and would be achieved predominantly by reducing allocated OR time to the surgeons.

Course Development Cycle Time: A Framework for Continuous Process Improvement.

ERIC Educational Resources Information Center

Lake, Erinn

2003-01-01

Details Edinboro University's efforts to reduce the extended cycle time required to develop new courses and programs. Describes a collaborative process improvement framework, illustrated data findings, the team's recommendations for improvement, and the outcomes of those recommendations. (EV)

The Capabilities of the U.S. Government to Collect and Analyze Economic Intelligence

DTIC Science & Technology

1994-01-01

by management ? Some economic and business aspects might not be critically time sensitive; however, knowledge about a competitor’s contract bid and...such a relationship include: reduced product research and development (R&D) timelines, reduced R&D costs, accelerated time from R&D to product marketing...intelligence that business cannot obtain on its own? 19 IimtIinua. Can the IC provide timely information to business in time for it to be used effectively

Manufacturing Enhancement through Reduction of Cycle Time using Different Lean Techniques

NASA Astrophysics Data System (ADS)

Suganthini Rekha, R.; Periyasamy, P.; Nallusamy, S.

2017-08-01

In recent manufacturing system the most important parameters in production line are work in process, TAKT time and line balancing. In this article lean tools and techniques were implemented to reduce the cycle time. The aim is to enhance the productivity of the water pump pipe by identifying the bottleneck stations and non value added activities. From the initial time study the bottleneck processes were identified and then necessary expanding processes were also identified for the bottleneck process. Subsequently the improvement actions have been established and implemented using different lean tools like value stream mapping, 5S and line balancing. The current state value stream mapping was developed to describe the existing status and to identify various problem areas. 5S was used to implement the steps to reduce the process cycle time and unnecessary movements of man and material. The improvement activities were implemented with required suggested and the future state value stream mapping was developed. From the results it was concluded that the total cycle time was reduced about 290.41 seconds and the customer demand has been increased about 760 units.

Impact of reduced near-field entrainment of overpressured volcanic jets on plume development

USGS Publications Warehouse

Saffaraval, Farhad; Solovitz, Stephen A.; Ogden, Darcy E.; Mastin, Larry G.

2012-01-01

Volcanic plumes are often studied using one-dimensional analytical models, which use an empirical entrainment ratio to close the equations. Although this ratio is typically treated as constant, its value near the vent is significantly reduced due to flow development and overpressured conditions. To improve the accuracy of these models, a series of experiments was performed using particle image velocimetry, a high-accuracy, full-field velocity measurement technique. Experiments considered a high-speed jet with Reynolds numbers up to 467,000 and exit pressures up to 2.93 times atmospheric. Exit gas densities were also varied from 0.18 to 1.4 times that of air. The measured velocity was integrated to determine entrainment directly. For jets with exit pressures near atmospheric, entrainment was approximately 30% less than the fully developed level at 20 diameters from the exit. At pressures nearly three times that of the atmosphere, entrainment was 60% less. These results were introduced into Plumeria, a one-dimensional plume model, to examine the impact of reduced entrainment. The maximum column height was only slightly modified, but the critical radius for collapse was significantly reduced, decreasing by nearly a factor of two at moderate eruptive pressures.

POD/DEIM reduced-order strategies for efficient four dimensional variational data assimilation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ştefănescu, R., E-mail: rstefane@vt.edu; Sandu, A., E-mail: sandu@cs.vt.edu; Navon, I.M., E-mail: inavon@fsu.edu

2015-08-15

This work studies reduced order modeling (ROM) approaches to speed up the solution of variational data assimilation problems with large scale nonlinear dynamical models. It is shown that a key requirement for a successful reduced order solution is that reduced order Karush–Kuhn–Tucker conditions accurately represent their full order counterparts. In particular, accurate reduced order approximations are needed for the forward and adjoint dynamical models, as well as for the reduced gradient. New strategies to construct reduced order based are developed for proper orthogonal decomposition (POD) ROM data assimilation using both Galerkin and Petrov–Galerkin projections. For the first time POD, tensorialmore » POD, and discrete empirical interpolation method (DEIM) are employed to develop reduced data assimilation systems for a geophysical flow model, namely, the two dimensional shallow water equations. Numerical experiments confirm the theoretical framework for Galerkin projection. In the case of Petrov–Galerkin projection, stabilization strategies must be considered for the reduced order models. The new reduced order shallow water data assimilation system provides analyses similar to those produced by the full resolution data assimilation system in one tenth of the computational time.« less

Convergence Acceleration and Documentation of CFD Codes for Turbomachinery Applications

NASA Technical Reports Server (NTRS)

Marquart, Jed E.

2005-01-01

The development and analysis of turbomachinery components for industrial and aerospace applications has been greatly enhanced in recent years through the advent of computational fluid dynamics (CFD) codes and techniques. Although the use of this technology has greatly reduced the time required to perform analysis and design, there still remains much room for improvement in the process. In particular, there is a steep learning curve associated with most turbomachinery CFD codes, and the computation times need to be reduced in order to facilitate their integration into standard work processes. Two turbomachinery codes have recently been developed by Dr. Daniel Dorney (MSFC) and Dr. Douglas Sondak (Boston University). These codes are entitled Aardvark (for 2-D and quasi 3-D simulations) and Phantom (for 3-D simulations). The codes utilize the General Equation Set (GES), structured grid methodology, and overset O- and H-grids. The codes have been used with success by Drs. Dorney and Sondak, as well as others within the turbomachinery community, to analyze engine components and other geometries. One of the primary objectives of this study was to establish a set of parametric input values which will enhance convergence rates for steady state simulations, as well as reduce the runtime required for unsteady cases. The goal is to reduce the turnaround time for CFD simulations, thus permitting more design parametrics to be run within a given time period. In addition, other code enhancements to reduce runtimes were investigated and implemented. The other primary goal of the study was to develop enhanced users manuals for Aardvark and Phantom. These manuals are intended to answer most questions for new users, as well as provide valuable detailed information for the experienced user. The existence of detailed user s manuals will enable new users to become proficient with the codes, as well as reducing the dependency of new users on the code authors. In order to achieve the objectives listed, the following tasks were accomplished: 1) Parametric Study Of Preconditioning Parameters And Other Code Inputs; 2) Code Modifications To Reduce Runtimes; 3) Investigation Of Compiler Options To Reduce Code Runtime; and 4) Development/Enhancement of Users Manuals for Aardvark and Phantom

Insect growth regulator effects of azadirachtin and neem oil on survivorship, development and fecundity of Aphis glycines (Homoptera: Aphididae) and its predator, Harmonia axyridis (Coleoptera: Coccinellidae).

PubMed

Kraiss, Heidi; Cullen, Eileen M

2008-06-01

Aphis glycines Matsumura, an invasive insect pest in North American soybeans, is fed upon by a key biological control agent, Harmonia axyridis Pallas. Although biological control is preferentially relied upon to suppress insect pests in organic agriculture, approved insecticides, such as neem, are periodically utilized to reduce damaging pest populations. The authors evaluated direct spray treatments of two neem formulations, azadirachtin and neem seed oil, under controlled conditions for effects on survivorship, development time and fecundity in A. glycines and H. axyridis. Both azadirachtin and neem seed oil significantly increased aphid nymphal mortality (80 and 77% respectively) while significantly increasing development time of those surviving to adulthood. First-instar H. axyridis survival to adulthood was also significantly reduced by both neem formulations, while only azadirachtin reduced third-instar survivorship. Azadirachtin increased H. axyridis development time to adult when applied to both instars, while neem oil only increased time to adult when applied to first instar. Neither neem formulation affected the fecundity of either insect. Results are discussed within the context of future laboratory and field studies aimed at clarifying if neem-derived insecticides can be effectively integrated with biological control for soybean aphid management in organic soybeans. Copyright (c) 2008 Society of Chemical Industry.

Computational Methods for HSCT-Inlet Controls/CFD Interdisciplinary Research

NASA Technical Reports Server (NTRS)

Cole, Gary L.; Melcher, Kevin J.; Chicatelli, Amy K.; Hartley, Tom T.; Chung, Joongkee

1994-01-01

A program aimed at facilitating the use of computational fluid dynamics (CFD) simulations by the controls discipline is presented. The objective is to reduce the development time and cost for propulsion system controls by using CFD simulations to obtain high-fidelity system models for control design and as numerical test beds for control system testing and validation. An interdisciplinary team has been formed to develop analytical and computational tools in three discipline areas: controls, CFD, and computational technology. The controls effort has focused on specifying requirements for an interface between the controls specialist and CFD simulations and a new method for extracting linear, reduced-order control models from CFD simulations. Existing CFD codes are being modified to permit time accurate execution and provide realistic boundary conditions for controls studies. Parallel processing and distributed computing techniques, along with existing system integration software, are being used to reduce CFD execution times and to support the development of an integrated analysis/design system. This paper describes: the initial application for the technology being developed, the high speed civil transport (HSCT) inlet control problem; activities being pursued in each discipline area; and a prototype analysis/design system in place for interactive operation and visualization of a time-accurate HSCT-inlet simulation.

Estimating replicate time shifts using Gaussian process regression

PubMed Central

Liu, Qiang; Andersen, Bogi; Smyth, Padhraic; Ihler, Alexander

2010-01-01

Motivation: Time-course gene expression datasets provide important insights into dynamic aspects of biological processes, such as circadian rhythms, cell cycle and organ development. In a typical microarray time-course experiment, measurements are obtained at each time point from multiple replicate samples. Accurately recovering the gene expression patterns from experimental observations is made challenging by both measurement noise and variation among replicates' rates of development. Prior work on this topic has focused on inference of expression patterns assuming that the replicate times are synchronized. We develop a statistical approach that simultaneously infers both (i) the underlying (hidden) expression profile for each gene, as well as (ii) the biological time for each individual replicate. Our approach is based on Gaussian process regression (GPR) combined with a probabilistic model that accounts for uncertainty about the biological development time of each replicate. Results: We apply GPR with uncertain measurement times to a microarray dataset of mRNA expression for the hair-growth cycle in mouse back skin, predicting both profile shapes and biological times for each replicate. The predicted time shifts show high consistency with independently obtained morphological estimates of relative development. We also show that the method systematically reduces prediction error on out-of-sample data, significantly reducing the mean squared error in a cross-validation study. Availability: Matlab code for GPR with uncertain time shifts is available at http://sli.ics.uci.edu/Code/GPRTimeshift/ Contact: ihler@ics.uci.edu PMID:20147305

An approach to the design of operations systems

NASA Technical Reports Server (NTRS)

Chafin, Roy L.; Curran, Patrick S.

1993-01-01

The MultiMission Control Team (MMCT) consists of mission controllers which provides Real-Time operations support for the Mars Observer project. The Real-Time Operations task is to insure the integrity of the ground data system, to insure that the configuration is correct to support the mission, and to monitor the spacecraft for the Spacecraft Team. Operations systems are typically developed by adapting operations systems from previous projects. Problems tend to be solved empirically when they are either anticipated or observed in testing. This development method has worked in the past when time was available for extensive Ops testing. In the present NASA budget environment, a more cost conscious design approach has become necessary. Cost is a concern because operations is an ongoing, continuous activity. Reducing costs entails reducing staff. Reducing staffing levels potentially increases the risk of mission failure. Therefore, keeping track of the risk level is necessary.

Comprehensive Investigation of Visibility Problems on Highways: Developing Real Time Monitoring and Prediction System for Reduced Visibility and Understanding Traffic and Human Factors Implications

DOT National Transportation Integrated Search

2017-07-01

Instances of fog or fog enhanced with smoke (non-photochemical smog) routinely reduce driver visibility on roadways throughout Georgia. Georgia has the fifth highest reduced-visibilityassociated crash frequency of any state. This report provides a...

Creating New Hope: Implementation of a Program To Reduce Poverty and Reform Welfare.

ERIC Educational Resources Information Center

Brock, Thomas; Doolittle, Fred; Fellerath, Veronica; Greenberg, David H.; Hollister, Robinson G., Jr.; Wiseman, Michael

The New Hope Project in Milwaukee, Wisconsin, was developed to reduce poverty and reform welfare by providing adults who are willing to work least 30 hours per week with the following: help obtaining a job, including time-limited, minimum wage community service jobs (CSJ) if full-time employment was not otherwise available; a monthly earnings…

Current warming will reduce yields unless maize breeding and seed systems adapt immediately

NASA Astrophysics Data System (ADS)

Challinor, A. J.; Koehler, A.-K.; Ramirez-Villegas, J.; Whitfield, S.; Das, B.

2016-10-01

The development of crop varieties that are better suited to new climatic conditions is vital for future food production. Increases in mean temperature accelerate crop development, resulting in shorter crop durations and reduced time to accumulate biomass and yield. The process of breeding, delivery and adoption (BDA) of new maize varieties can take up to 30 years. Here, we assess for the first time the implications of warming during the BDA process by using five bias-corrected global climate models and four representative concentration pathways with realistic scenarios of maize BDA times in Africa. The results show that the projected difference in temperature between the start and end of the maize BDA cycle results in shorter crop durations that are outside current variability. Both adaptation and mitigation can reduce duration loss. In particular, climate projections have the potential to provide target elevated temperatures for breeding. Whilst options for reducing BDA time are highly context dependent, common threads include improved recording and sharing of data across regions for the whole BDA cycle, streamlining of regulation, and capacity building. Finally, we show that the results have implications for maize across the tropics, where similar shortening of duration is projected.

Development and Appraisal of Multiple Accounting Record System (Mars).

PubMed

Yu, H C; Chen, M C

2016-01-01

The aim of the system is to achieve simplification of workflow, reduction of recording time, and increase the income for the study hospital. The project team decided to develop a multiple accounting record system that generates the account records based on the nursing records automatically, reduces the time and effort for nurses to review the procedure and provide another note of material consumption. Three configuration files were identified to demonstrate the relationship of treatments and reimbursement items. The workflow was simplified. The nurses averagely reduced 10 minutes of daily recording time, and the reimbursement points have been increased by 7.49%. The project streamlined the workflow and provides the institute a better way in finical management.

Methodological Guidelines for Reducing the Complexity of Data Warehouse Development for Transactional Blood Bank Systems

PubMed Central

Takecian, Pedro L.; Oikawa, Marcio K.; Braghetto, Kelly R.; Rocha, Paulo; Lucena, Fred; Kavounis, Katherine; Schlumpf, Karen S.; Acker, Susan; Carneiro-Proietti, Anna B. F.; Sabino, Ester C.; Custer, Brian; Busch, Michael P.; Ferreira, João E.

2013-01-01

Over time, data warehouse (DW) systems have become more difficult to develop because of the growing heterogeneity of data sources. Despite advances in research and technology, DW projects are still too slow for pragmatic results to be generated. Here, we address the following question: how can the complexity of DW development for integration of heterogeneous transactional information systems be reduced? To answer this, we proposed methodological guidelines based on cycles of conceptual modeling and data analysis, to drive construction of a modular DW system. These guidelines were applied to the blood donation domain, successfully reducing the complexity of DW development. PMID:23729945

Methodological Guidelines for Reducing the Complexity of Data Warehouse Development for Transactional Blood Bank Systems.

PubMed

Takecian, Pedro L; Oikawa, Marcio K; Braghetto, Kelly R; Rocha, Paulo; Lucena, Fred; Kavounis, Katherine; Schlumpf, Karen S; Acker, Susan; Carneiro-Proietti, Anna B F; Sabino, Ester C; Custer, Brian; Busch, Michael P; Ferreira, João E

2013-06-01

Over time, data warehouse (DW) systems have become more difficult to develop because of the growing heterogeneity of data sources. Despite advances in research and technology, DW projects are still too slow for pragmatic results to be generated. Here, we address the following question: how can the complexity of DW development for integration of heterogeneous transactional information systems be reduced? To answer this, we proposed methodological guidelines based on cycles of conceptual modeling and data analysis, to drive construction of a modular DW system. These guidelines were applied to the blood donation domain, successfully reducing the complexity of DW development.

Evaluation of focused ultrasound algorithms: Issues for reducing pre-focal heating and treatment time.

PubMed

Yiannakou, Marinos; Trimikliniotis, Michael; Yiallouras, Christos; Damianou, Christakis

2016-02-01

Due to the heating in the pre-focal field the delay between successive movements in high intensity focused ultrasound (HIFU) are sometimes as long as 60s, resulting to treatment time in the order of 2-3h. Because there is generally a requirement to reduce treatment time, we were motivated to explore alternative transducer motion algorithms in order to reduce pre-focal heating and treatment time. A 1 MHz single element transducer with 4 cm diameter and 10 cm focal length was used. A simulation model was developed that estimates the temperature, thermal dose and lesion development in the pre-focal field. The simulated temperature history that was combined with the motion algorithms produced thermal maps in the pre-focal region. Polyacrylimde gel phantom was used to evaluate the induced pre-focal heating for each motion algorithm used, and also was used to assess the accuracy of the simulation model. Three out of the six algorithms having successive steps close to each other, exhibited severe heating in the pre-focal field. Minimal heating was produced with the algorithms having successive steps apart from each other (square, square spiral and random). The last three algorithms were improved further (with small cost in time), thus eliminating completely the pre-focal heating and reducing substantially the treatment time as compared to traditional algorithms. Out of the six algorithms, 3 were successful in eliminating the pre-focal heating completely. Because these 3 algorithms required no delay between successive movements (except in the last part of the motion), the treatment time was reduced by 93%. Therefore, it will be possible in the future, to achieve treatment time of focused ultrasound therapies shorter than 30 min. The rate of ablated volume achieved with one of the proposed algorithms was 71 cm(3)/h. The intention of this pilot study was to demonstrate that the navigation algorithms play the most important role in reducing pre-focal heating. By evaluating in the future, all commercially available geometries, it will be possible to reduce the treatment time, for thermal ablation protocols intended for oncological targets. Copyright © 2015 Elsevier B.V. All rights reserved.

A first-generation software product line for data acquisition systems in astronomy

NASA Astrophysics Data System (ADS)

López-Ruiz, J. C.; Heradio, Rubén; Cerrada Somolinos, José Antonio; Coz Fernandez, José Ramón; López Ramos, Pablo

2008-07-01

This article presents a case study on developing a software product line for data acquisition systems in astronomy based on the Exemplar Driven Development methodology and the Exemplar Flexibilization Language tool. The main strategies to build the software product line are based on the domain commonality and variability, the incremental scope and the use of existing artifacts. It consists on a lean methodology with little impact on the organization, suitable for small projects, which reduces product line start-up time. Software Product Lines focuses on creating a family of products instead of individual products. This approach has spectacular benefits on reducing the time to market, maintaining the know-how, reducing the development costs and increasing the quality of new products. The maintenance of the products is also enhanced since all the data acquisition systems share the same product line architecture.

Nuclear Thermal Propulsion Development Risks

NASA Technical Reports Server (NTRS)

Kim, Tony

2015-01-01

There are clear advantages of development of a Nuclear Thermal Propulsion (NTP) for a crewed mission to Mars. NTP for in-space propulsion enables more ambitious space missions by providing high thrust at high specific impulse ((is) approximately 900 sec) that is 2 times the best theoretical performance possible for chemical rockets. Missions can be optimized for maximum payload capability to take more payload with reduced total mass to orbit; saving cost on reduction of the number of launch vehicles needed. Or missions can be optimized to minimize trip time significantly to reduce the deep space radiation exposure to the crew. NTR propulsion technology is a game changer for space exploration to Mars and beyond. However, 'NUCLEAR' is a word that is feared and vilified by some groups and the hostility towards development of any nuclear systems can meet great opposition by the public as well as from national leaders and people in authority. The public often associates the 'nuclear' word with weapons of mass destruction. The development NTP is at risk due to unwarranted public fears and clear honest communication of nuclear safety will be critical to the success of the development of the NTP technology. Reducing cost to NTP development is critical to its acceptance and funding. In the past, highly inflated cost estimates of a full-scale development nuclear engine due to Category I nuclear security requirements and costly regulatory requirements have put the NTP technology as a low priority. Innovative approaches utilizing low enriched uranium (LEU). Even though NTP can be a small source of radiation to the crew, NTP can facilitate significant reduction of crew exposure to solar and cosmic radiation by reducing trip times by 3-4 months. Current Human Mars Mission (HMM) trajectories with conventional propulsion systems and fuel-efficient transfer orbits exceed astronaut radiation exposure limits. Utilizing extra propellant from one additional SLS launch and available energy in the NTP fuel, HMM radiation exposure can be reduced significantly.

Development of Electromagnetically Actuated Vacuum Circuit Breaker for 72kV Rated Switchgear

NASA Astrophysics Data System (ADS)

Kim, Tae-Hyun; Tsukima, Mitsuru; Maruyama, Akihiko; Takahara, Osamu; Haruna, Kazushi; Yano, Tomotaka; Matsunaga, Toshihiro; Imamura, Kazuaki; Arioka, Masahiro; Takeuchi, Toshie

A new electromagnetically actuated vacuum circuit breaker (VCB) has been developed for a 72kV rated switchgear. Each phase of this VCB has a plurality of compact electromagnetic actuators linked mechanically providing the required driving energy. The mechanical linkage working as a lever magnifies an actuator stroke to the required stroke of a 72kV rated vacuum interrupter. An electromagnetic analysis coupled with motion, which considers the mechanical linkage of the plural actuators, has been developed for designing the driving behavior of this VCB. Using this analytical method and a quality engineering method known as the Taguchi method, we have clarified effective parameters to reduce the time difference of the driving behavior for tolerance specifications. Moreover, analyzing the oscillatory behavior closing the contacts, a structure of this VCB has been designed to reduce the bounce duration. The developed new VCB has been confirmed that a time difference is short enough and bounce duration is reduced. This VCB is highly reliable against variations in manufacturing and environment.

The Effects of Royal Jelly on Fitness Traits and Gene Expression in Drosophila melanogaster

PubMed Central

Shorter, John R.; Geisz, Matthew; Özsoy, Ergi; Magwire, Michael M.; Carbone, Mary Anna; Mackay, Trudy F. C.

2015-01-01

Royal Jelly (RJ) is a product made by honey bee workers and is required for queen differentiation and accompanying changes in queen body size, development time, lifespan and reproductive output relative to workers. Previous studies have reported similar changes in Drosophila melanogaster in response to RJ. Here, we quantified viability, development time, body size, productivity, lifespan and genome wide transcript abundance of D. melanogaster reared on standard culture medium supplemented with increasing concentrations of RJ. We found that lower concentrations of RJ do induce significant differences in body size in both sexes; higher concentrations reduce size, increase mortality, shorten lifespan and reduce productivity. Increased concentrations of RJ also consistently lengthened development time in both sexes. RJ is associated with changes in expression of 1,581 probe sets assessed using Affymetrix Drosophila 2.0 microarrays, which were enriched for genes associated with metabolism and amino acid degradation. The transcriptional changes are consistent with alterations in cellular processes to cope with excess nutrients provided by RJ, including biosynthesis and detoxification, which might contribute to accelerated senescence and reduced lifespan. PMID:26226016

NASA's Aero-Space Technology

NASA Technical Reports Server (NTRS)

Milstead, Phil

2000-01-01

This presentation reviews the three pillars and the associated goals of NASA's Aero-Space Technology Enterprise. The three pillars for success are: (1) Global Civil Aviation, (2) Revolutionary Technology Leaps, (3) Advanced Space Transportation. The associated goals of the first pillar are to reduce accidents, emissions, and cost, and to increase the aviation system capacity. The goals of the second pillar are to reduce transoceanic travel time, revolutionize general aviation aircraft, and improve development capacity. The goals associated with the third pillar are to reduce the launch cost for low earth orbit and to reduce travel time for planetary missions. In order to meet these goals NASA must provide next-generation design capability for new and or experimental craft which enable a balance between reducing components of the design cycle by up to 50% and or increasing the confidence in design by 50%. These next-generation design tools, concepts, and processes will revolutionize vehicle development. The presentation finally reviews the importance of modeling and simulation in achieving the goals.

Connected Vehicle Technologies for Efficient Urban Transportation

DOT National Transportation Integrated Search

2016-10-24

Connected vehicle technology is employed to optimize the vehicle's control system in real-time to reduce congestion, improve fuel economy, and reduce emissions. This project's goal was to develop a two-way communication system to upload vehicle data ...

Projection-Based Reduced Order Modeling for Spacecraft Thermal Analysis

NASA Technical Reports Server (NTRS)

Qian, Jing; Wang, Yi; Song, Hongjun; Pant, Kapil; Peabody, Hume; Ku, Jentung; Butler, Charles D.

2015-01-01

This paper presents a mathematically rigorous, subspace projection-based reduced order modeling (ROM) methodology and an integrated framework to automatically generate reduced order models for spacecraft thermal analysis. Two key steps in the reduced order modeling procedure are described: (1) the acquisition of a full-scale spacecraft model in the ordinary differential equation (ODE) and differential algebraic equation (DAE) form to resolve its dynamic thermal behavior; and (2) the ROM to markedly reduce the dimension of the full-scale model. Specifically, proper orthogonal decomposition (POD) in conjunction with discrete empirical interpolation method (DEIM) and trajectory piece-wise linear (TPWL) methods are developed to address the strong nonlinear thermal effects due to coupled conductive and radiative heat transfer in the spacecraft environment. Case studies using NASA-relevant satellite models are undertaken to verify the capability and to assess the computational performance of the ROM technique in terms of speed-up and error relative to the full-scale model. ROM exhibits excellent agreement in spatiotemporal thermal profiles (<0.5% relative error in pertinent time scales) along with salient computational acceleration (up to two orders of magnitude speed-up) over the full-scale analysis. These findings establish the feasibility of ROM to perform rational and computationally affordable thermal analysis, develop reliable thermal control strategies for spacecraft, and greatly reduce the development cycle times and costs.

Parametric reduced models for the nonlinear Schrödinger equation

NASA Astrophysics Data System (ADS)

Harlim, John; Li, Xiantao

2015-05-01

Reduced models for the (defocusing) nonlinear Schrödinger equation are developed. In particular, we develop reduced models that only involve the low-frequency modes given noisy observations of these modes. The ansatz of the reduced parametric models are obtained by employing a rational approximation and a colored-noise approximation, respectively, on the memory terms and the random noise of a generalized Langevin equation that is derived from the standard Mori-Zwanzig formalism. The parameters in the resulting reduced models are inferred from noisy observations with a recently developed ensemble Kalman filter-based parametrization method. The forecasting skill across different temperature regimes are verified by comparing the moments up to order four, a two-time correlation function statistics, and marginal densities of the coarse-grained variables.

Parametric reduced models for the nonlinear Schrödinger equation.

PubMed

Harlim, John; Li, Xiantao

2015-05-01

Reduced models for the (defocusing) nonlinear Schrödinger equation are developed. In particular, we develop reduced models that only involve the low-frequency modes given noisy observations of these modes. The ansatz of the reduced parametric models are obtained by employing a rational approximation and a colored-noise approximation, respectively, on the memory terms and the random noise of a generalized Langevin equation that is derived from the standard Mori-Zwanzig formalism. The parameters in the resulting reduced models are inferred from noisy observations with a recently developed ensemble Kalman filter-based parametrization method. The forecasting skill across different temperature regimes are verified by comparing the moments up to order four, a two-time correlation function statistics, and marginal densities of the coarse-grained variables.

Reducing the ecological consequences of night-time light pollution: options and developments

PubMed Central

Gaston, Kevin J; Davies, Thomas W; Bennie, Jonathan; Hopkins, John

2012-01-01

1. Much concern has been expressed about the ecological consequences of night-time light pollution. This concern is most often focused on the encroachment of artificial light into previously unlit areas of the night-time environment, but changes in the spectral composition, duration and spatial pattern of light are also recognized as having ecological effects. 2. Here, we examine the potential consequences for organisms of five management options to reduce night-time light pollution. These are to (i) prevent areas from being artificially lit; (ii) limit the duration of lighting; (iii) reduce the ‘trespass’ of lighting into areas that are not intended to be lit (including the night sky); (iv) change the intensity of lighting; and (v) change the spectral composition of lighting. 3. Maintaining and increasing natural unlit areas is likely to be the most effective option for reducing the ecological effects of lighting. However, this will often conflict with other social and economic objectives. Decreasing the duration of lighting will reduce energy costs and carbon emissions, but is unlikely to alleviate many impacts on nocturnal and crepuscular animals, as peak times of demand for lighting frequently coincide with those in the activities of these species. Reducing the trespass of lighting will maintain heterogeneity even in otherwise well-lit areas, providing dark refuges that mobile animals can exploit. Decreasing the intensity of lighting will reduce energy consumption and limit both skyglow and the area impacted by high-intensity direct light. Shifts towards ‘whiter’ light are likely to increase the potential range of environmental impacts as light is emitted across a broader range of wavelengths. 4. Synthesis and applications. The artificial lightscape will change considerably over coming decades with the drive for more cost-effective low-carbon street lighting solutions and growth in the artificially lit area. Developing lighting strategies that minimize adverse ecological impacts while balancing the often conflicting requirements of light for human utility, comfort and safety, aesthetic concerns, energy consumption and carbon emission reduction constitute significant future challenges. However, as both lighting technology and understanding of its ecological effects develop, there is potential to identify adaptive solutions that resolve these conflicts. PMID:23335816

Reducing the ecological consequences of night-time light pollution: options and developments.

PubMed

Gaston, Kevin J; Davies, Thomas W; Bennie, Jonathan; Hopkins, John

2012-12-01

1. Much concern has been expressed about the ecological consequences of night-time light pollution. This concern is most often focused on the encroachment of artificial light into previously unlit areas of the night-time environment, but changes in the spectral composition, duration and spatial pattern of light are also recognized as having ecological effects.2. Here, we examine the potential consequences for organisms of five management options to reduce night-time light pollution. These are to (i) prevent areas from being artificially lit; (ii) limit the duration of lighting; (iii) reduce the 'trespass' of lighting into areas that are not intended to be lit (including the night sky); (iv) change the intensity of lighting; and (v) change the spectral composition of lighting.3. Maintaining and increasing natural unlit areas is likely to be the most effective option for reducing the ecological effects of lighting. However, this will often conflict with other social and economic objectives. Decreasing the duration of lighting will reduce energy costs and carbon emissions, but is unlikely to alleviate many impacts on nocturnal and crepuscular animals, as peak times of demand for lighting frequently coincide with those in the activities of these species. Reducing the trespass of lighting will maintain heterogeneity even in otherwise well-lit areas, providing dark refuges that mobile animals can exploit. Decreasing the intensity of lighting will reduce energy consumption and limit both skyglow and the area impacted by high-intensity direct light. Shifts towards 'whiter' light are likely to increase the potential range of environmental impacts as light is emitted across a broader range of wavelengths.4.Synthesis and applications. The artificial lightscape will change considerably over coming decades with the drive for more cost-effective low-carbon street lighting solutions and growth in the artificially lit area. Developing lighting strategies that minimize adverse ecological impacts while balancing the often conflicting requirements of light for human utility, comfort and safety, aesthetic concerns, energy consumption and carbon emission reduction constitute significant future challenges. However, as both lighting technology and understanding of its ecological effects develop, there is potential to identify adaptive solutions that resolve these conflicts.

The optimal manufacturing batch size with rework under time-varying demand process for a finite time horizon

NASA Astrophysics Data System (ADS)

Musa, Sarah; Supadi, Siti Suzlin; Omar, Mohd

2014-07-01

Rework is one of the solutions to some of the main issues in reverse logistic and green supply chain as it reduces production cost and environmental problem. Many researchers focus on developing rework model, but to the knowledge of the author, none of them has developed a model for time-varying demand rate. In this paper, we extend previous works and develop multiple batch production system for time-varying demand rate with rework. In this model, the rework is done within the same production cycle.

Real-time simulation of an airborne radar for overwater approaches

NASA Technical Reports Server (NTRS)

Karmarkar, J.; Clark, D.

1982-01-01

Software developed to provide a real time simulation of an airborne radar for overwater approaches to oil rig platforms is documented. The simulation is used to study advanced concepts for enhancement of airborne radar approaches (ARA) in order to reduce crew workload, improve approach tracking precision, and reduce weather minimums. ARA's are currently used for offshore helicopter operations to and from oil rigs.

High-throughput process development: determination of dynamic binding capacity using microtiter filter plates filled with chromatography resin.

PubMed

Bergander, Tryggve; Nilsson-Välimaa, Kristina; Oberg, Katarina; Lacki, Karol M

2008-01-01

Steadily increasing demand for more efficient and more affordable biomolecule-based therapies put a significant burden on biopharma companies to reduce the cost of R&D activities associated with introduction of a new drug to the market. Reducing the time required to develop a purification process would be one option to address the high cost issue. The reduction in time can be accomplished if more efficient methods/tools are available for process development work, including high-throughput techniques. This paper addresses the transitions from traditional column-based process development to a modern high-throughput approach utilizing microtiter filter plates filled with a well-defined volume of chromatography resin. The approach is based on implementing the well-known batch uptake principle into microtiter plate geometry. Two variants of the proposed approach, allowing for either qualitative or quantitative estimation of dynamic binding capacity as a function of residence time, are described. Examples of quantitative estimation of dynamic binding capacities of human polyclonal IgG on MabSelect SuRe and of qualitative estimation of dynamic binding capacity of amyloglucosidase on a prototype of Capto DEAE weak ion exchanger are given. The proposed high-throughput method for determination of dynamic binding capacity significantly reduces time and sample consumption as compared to a traditional method utilizing packed chromatography columns without sacrificing the accuracy of data obtained.

Activating clinical trials: a process improvement approach.

PubMed

Martinez, Diego A; Tsalatsanis, Athanasios; Yalcin, Ali; Zayas-Castro, José L; Djulbegovic, Benjamin

2016-02-24

The administrative process associated with clinical trial activation has been criticized as costly, complex, and time-consuming. Prior research has concentrated on identifying administrative barriers and proposing various solutions to reduce activation time, and consequently associated costs. Here, we expand on previous research by incorporating social network analysis and discrete-event simulation to support process improvement decision-making. We searched for all operational data associated with the administrative process of activating industry-sponsored clinical trials at the Office of Clinical Research of the University of South Florida in Tampa, Florida. We limited the search to those trials initiated and activated between July 2011 and June 2012. We described the process using value stream mapping, studied the interactions of the various process participants using social network analysis, and modeled potential process modifications using discrete-event simulation. The administrative process comprised 5 sub-processes, 30 activities, 11 decision points, 5 loops, and 8 participants. The mean activation time was 76.6 days. Rate-limiting sub-processes were those of contract and budget development. Key participants during contract and budget development were the Office of Clinical Research, sponsors, and the principal investigator. Simulation results indicate that slight increments on the number of trials, arriving to the Office of Clinical Research, would increase activation time by 11 %. Also, incrementing the efficiency of contract and budget development would reduce the activation time by 28 %. Finally, better synchronization between contract and budget development would reduce time spent on batching documentation; however, no improvements would be attained in total activation time. The presented process improvement analytic framework not only identifies administrative barriers, but also helps to devise and evaluate potential improvement scenarios. The strength of our framework lies in its system analysis approach that recognizes the stochastic duration of the activation process and the interdependence between process activities and entities.

Parallel processing architecture for computing inverse differential kinematic equations of the PUMA arm

NASA Technical Reports Server (NTRS)

Hsia, T. C.; Lu, G. Z.; Han, W. H.

1987-01-01

In advanced robot control problems, on-line computation of inverse Jacobian solution is frequently required. Parallel processing architecture is an effective way to reduce computation time. A parallel processing architecture is developed for the inverse Jacobian (inverse differential kinematic equation) of the PUMA arm. The proposed pipeline/parallel algorithm can be inplemented on an IC chip using systolic linear arrays. This implementation requires 27 processing cells and 25 time units. Computation time is thus significantly reduced.

Cotton regeneration in vitro

USDA-ARS?s Scientific Manuscript database

H. F. Sakhanokho and K. Rajasekaran Over the years, plant breeders have improved cotton via conventional breeding methods, but these methods are time-consuming. To complement classical breeding and, at times, reduce the time necessary for new cultivar development, breeders have turned to in vitro ...

Composite Case Development for Weapons Applications and Testing

DTIC Science & Technology

2015-03-01

5 cm axial location for each layer. ............................................................... 68  Figure 52.  Hydra radiographic time sequence...increase by 6.7%. No significant change in hold time was observed for the model with reduced mass. Figure 52. Hydra radiographic time sequence of

Fast cooldown coaxial pulse tube microcooler

NASA Astrophysics Data System (ADS)

Nast, T.; Olson, J. R.; Champagne, P.; Roth, E.; Kaldas, G.; Saito, E.; Loung, V.; McCay, B. S.; Kenton, A. C.; Dobbins, C. L.

2016-05-01

We report the development and initial testing of the Lockheed Martin first-article, single-stage, compact, coaxial, Fast Cooldown Pulse Tube Microcryocooler (FC-PTM). The new cryocooler supports cooling requirements for emerging large, high operating temperature (105-150K) infrared focal plane array sensors with nominal cooling loads of ~300 mW @105K @293K ambient. This is a sequel development that builds on our inline and coaxial pulse tube microcryocoolers reported at CEC 20137, ICC188,9, and CEC201510. The new FC-PTM and the prior units all share our long life space technology attributes, which typically have 10 year life requirements1. The new prototype microcryocooler builds on the previous development by incorporating cold head design improvements in two key areas: 1) reduced cool-down time and 2) novel repackaging that greatly reduces envelope. The new coldhead and Dewar were significantly redesigned from the earlier versions in order to achieve a cooldown time of 2-3 minutes-- a projected requirement for tactical applications. A design approach was devised to reduce the cold head length from 115mm to 55mm, while at the same time reducing cooldown time. We present new FC-PTM performance test measurements with comparisons to our previous pulse-tube microcryocooler measurements and design predictions. The FC-PTM exhibits attractive small size, volume, weight, power and cost (SWaP-C) features with sufficient cooling capacity over required ambient conditions that apply to an increasing variety of space and tactical applications.

Fast cool-down coaxial pulse tube microcooler

NASA Astrophysics Data System (ADS)

Nast, T.; Olson, J. R.; Champagne, P.; Roth, E.; Kaldas, G.; Saito, E.; Loung, V.; McCay, B. S.; Kenton, A. C.; Dobbins, C. L.

2016-09-01

We report the development and initial testing of the Lockheed Martin first-article, single-stage, compact, coaxial, Fast Cooldown Pulse Tube Microcryocooler (FC-PTM). The new cryocooler supports cooling requirements for emerging large, high operating temperature (105-150K) infrared focal plane array sensors with nominal cooling loads of 300 mW @105K @293K ambient. This is a sequel development that builds on our inline and coaxial pulse tube microcryocoolers reported at CEC 20137, ICC188,9, and CEC201510. The new FC-PTM and the prior units all share our long life space technology attributes, which typically have 10 year life requirements1. The new prototype microcryocooler builds on the previous development by incorporating cold head design improvements in two key areas: 1) reduced cool-down time and 2) novel repackaging that greatly reduces envelope. The new coldhead and Dewar were significantly redesigned from the earlier versions in order to achieve a cooldown time of 2-3 minutes- a projected requirement for tactical applications. A design approach was devised to reduce the cold head length from 115mm to 55mm, while at the same time reducing cooldown time. We present new FC-PTM performance test measurements with comparisons to our previous pulse-tube microcryocooler measurements and design predictions. The FC-PTM exhibits attractive small size, volume, weight, power and cost (SWaP-C) features with sufficient cooling capacity over required ambient conditions that apply to an increasing variety of space and tactical applications.

Automated real-time software development

NASA Technical Reports Server (NTRS)

Jones, Denise R.; Walker, Carrie K.; Turkovich, John J.

1993-01-01

A Computer-Aided Software Engineering (CASE) system has been developed at the Charles Stark Draper Laboratory (CSDL) under the direction of the NASA Langley Research Center. The CSDL CASE tool provides an automated method of generating source code and hard copy documentation from functional application engineering specifications. The goal is to significantly reduce the cost of developing and maintaining real-time scientific and engineering software while increasing system reliability. This paper describes CSDL CASE and discusses demonstrations that used the tool to automatically generate real-time application code.

Materials Genome Initiative Element

NASA Technical Reports Server (NTRS)

Vickers, John

2015-01-01

NASA is committed to developing new materials and manufacturing methods that can enable new missions with ever increasing mission demands. Typically, the development and certification of new materials and manufacturing methods in the aerospace industry has required more than 20 years of development time with a costly testing and certification program. To reduce the cost and time to mature these emerging technologies, NASA is developing computational materials tools to improve understanding of the material and guide the certification process.

Supply and demand: application of Lean Six Sigma methods to improve drug round efficiency and release nursing time.

PubMed

Kieran, Maríosa; Cleary, Mary; De Brún, Aoife; Igoe, Aileen

2017-10-01

To improve efficiency, reduce interruptions and reduce the time taken to complete oral drug rounds. Lean Six Sigma methods were applied to improve drug round efficiency using a pre- and post-intervention design. A 20-bed orthopaedic ward in a large teaching hospital in Ireland. Pharmacy, nursing and quality improvement staff. A multifaceted intervention was designed which included changes in processes related to drug trolley organization and drug supply planning. A communications campaign aimed at reducing interruptions during nurse-led during rounds was also developed and implemented. Average number of interruptions, average drug round time and variation in time taken to complete drug round. At baseline, the oral drug round took an average of 125 min. Following application of Lean Six Sigma methods, the average drug round time decreased by 51 min. The average number of interruptions per drug round reduced from an average of 12 at baseline to 11 following intervention, with a 75% reduction in drug supply interruptions. Lean Six Sigma methodology was successfully employed to reduce interruptions and to reduce time taken to complete the oral drug round. © The Author 2017. Published by Oxford University Press in association with the International Society for Quality in Health Care. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com

Integrated Test Approach

NASA Technical Reports Server (NTRS)

Cotton, Will; Liechty, John

2015-01-01

This paper describes a testing methodology undertaken on the Facilities Development and Operations Contract (FDOC) by Lockheed Martin. The methodology was defined with the intent of reducing project schedule time to enable NASA's Johnson Space Center (JSC) to be able to deliver the Mission Control Center (MCC) 21 project as quickly as possible. 21 represents the 21st century where NASA JSC is updating its control center with new technology and operational concepts in order to support NASA customers wanting to use control center assets to support space vehicle operations. In collaboration with the NASA customer, a new test concept was conceived early during MCC21 project planning with the goal of reducing project delivery time. One enabler that could help reduce delivery time was testing. Within the project, testing was performed by two entities, software development responsible for subsystem testing and system test responsible for system integration testing. The MCC21 project took a deliberate review of testing to determine how it could be performed differently to realize an overall reduction in test time to support the goal of a more rapid project delivery.

Reducing Design Cycle Time and Cost Through Process Resequencing

NASA Technical Reports Server (NTRS)

Rogers, James L.

2004-01-01

In today's competitive environment, companies are under enormous pressure to reduce the time and cost of their design cycle. One method for reducing both time and cost is to develop an understanding of the flow of the design processes and the effects of the iterative subcycles that are found in complex design projects. Once these aspects are understood, the design manager can make decisions that take advantage of decomposition, concurrent engineering, and parallel processing techniques to reduce the total time and the total cost of the design cycle. One software tool that can aid in this decision-making process is the Design Manager's Aid for Intelligent Decomposition (DeMAID). The DeMAID software minimizes the feedback couplings that create iterative subcycles, groups processes into iterative subcycles, and decomposes the subcycles into a hierarchical structure. The real benefits of producing the best design in the least time and at a minimum cost are obtained from sequencing the processes in the subcycles.

Reducing neural network training time with parallel processing

NASA Technical Reports Server (NTRS)

Rogers, James L., Jr.; Lamarsh, William J., II

1995-01-01

Obtaining optimal solutions for engineering design problems is often expensive because the process typically requires numerous iterations involving analysis and optimization programs. Previous research has shown that a near optimum solution can be obtained in less time by simulating a slow, expensive analysis with a fast, inexpensive neural network. A new approach has been developed to further reduce this time. This approach decomposes a large neural network into many smaller neural networks that can be trained in parallel. Guidelines are developed to avoid some of the pitfalls when training smaller neural networks in parallel. These guidelines allow the engineer: to determine the number of nodes on the hidden layer of the smaller neural networks; to choose the initial training weights; and to select a network configuration that will capture the interactions among the smaller neural networks. This paper presents results describing how these guidelines are developed.

Developing the Librarians' Role in Supporting Grant Applications and Reducing Waste in Research: Outcomes from a Literature Review and Survey in the NIHR Research Design Service

ERIC Educational Resources Information Center

Edmunds Otter, Mary L.; Wright, Judy M.; King, Natalie V.

2017-01-01

Librarians and information specialists' involvement during the development of grant applications for external funding can save researchers' time, provide specialist support, and contribute to reducing avoidable waste in research. This article presents a survey of information specialists working for the National Institute for Health Research's…

A real-time recursive filter for the attitude determination of the Spacelab instrument pointing subsystem

NASA Technical Reports Server (NTRS)

West, M. E.

1992-01-01

A real-time estimation filter which reduces sensitivity to system variations and reduces the amount of preflight computation is developed for the instrument pointing subsystem (IPS). The IPS is a three-axis stabilized platform developed to point various astronomical observation instruments aboard the shuttle. Currently, the IPS utilizes a linearized Kalman filter (LKF), with premission defined gains, to compensate for system drifts and accumulated attitude errors. Since the a priori gains are generated for an expected system, variations result in a suboptimal estimation process. This report compares the performance of three real-time estimation filters with the current LKF implementation. An extended Kalman filter and a second-order Kalman filter are developed to account for the system nonlinearities, while a linear Kalman filter implementation assumes that the nonlinearities are negligible. The performance of each of the four estimation filters are compared with respect to accuracy, stability, settling time, robustness, and computational requirements. It is shown, that for the current IPS pointing requirements, the linear Kalman filter provides improved robustness over the LKF with less computational requirements than the two real-time nonlinear estimation filters.

DART system analysis.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boggs, Paul T.; Althsuler, Alan; Larzelere, Alex R.

2005-08-01

The Design-through-Analysis Realization Team (DART) is chartered with reducing the time Sandia analysts require to complete the engineering analysis process. The DART system analysis team studied the engineering analysis processes employed by analysts in Centers 9100 and 8700 at Sandia to identify opportunities for reducing overall design-through-analysis process time. The team created and implemented a rigorous analysis methodology based on a generic process flow model parameterized by information obtained from analysts. They also collected data from analysis department managers to quantify the problem type and complexity distribution throughout Sandia's analyst community. They then used this information to develop a communitymore » model, which enables a simple characterization of processes that span the analyst community. The results indicate that equal opportunity for reducing analysis process time is available both by reducing the ''once-through'' time required to complete a process step and by reducing the probability of backward iteration. In addition, reducing the rework fraction (i.e., improving the engineering efficiency of subsequent iterations) offers approximately 40% to 80% of the benefit of reducing the ''once-through'' time or iteration probability, depending upon the process step being considered. Further, the results indicate that geometry manipulation and meshing is the largest portion of an analyst's effort, especially for structural problems, and offers significant opportunity for overall time reduction. Iteration loops initiated late in the process are more costly than others because they increase ''inner loop'' iterations. Identifying and correcting problems as early as possible in the process offers significant opportunity for time savings.« less

An exploratory study of a finite difference method for calculating unsteady transonic potential flow

NASA Technical Reports Server (NTRS)

Bennett, R. M.; Bland, S. R.

1979-01-01

A method for calculating transonic flow over steady and oscillating airfoils was developed by Isogai. The full potential equation is solved with a semi-implicit, time-marching, finite difference technique. Steady flow solutions are obtained from time asymptotic solutions for a steady airfoil. Corresponding oscillatory solutions are obtained by initiating an oscillation and marching in time for several cycles until a converged periodic solution is achieved. The method is described in general terms and results for the case of an airfoil with an oscillating flap are presented for Mach numbers 0.500 and 0.875. Although satisfactory results are obtained for some reduced frequencies, it is found that the numerical technique generates spurious oscillations in the indicial response functions and in the variation of the aerodynamic coefficients with reduced frequency. These oscillations are examined with a dynamic data reduction method to evaluate their effects and trends with reduced frequency and Mach number. Further development of the numerical method is needed to eliminate these oscillations.

Development and comparison of advanced reduced-basis methods for the transient structural analysis of unconstrained structures

NASA Technical Reports Server (NTRS)

Mcgowan, David M.; Bostic, Susan W.; Camarda, Charles J.

1993-01-01

The development of two advanced reduced-basis methods, the force derivative method and the Lanczos method, and two widely used modal methods, the mode displacement method and the mode acceleration method, for transient structural analysis of unconstrained structures is presented. Two example structural problems are studied: an undamped, unconstrained beam subject to a uniformly distributed load which varies as a sinusoidal function of time and an undamped high-speed civil transport aircraft subject to a normal wing tip load which varies as a sinusoidal function of time. These example problems are used to verify the methods and to compare the relative effectiveness of each of the four reduced-basis methods for performing transient structural analyses on unconstrained structures. The methods are verified with a solution obtained by integrating directly the full system of equations of motion, and they are compared using the number of basis vectors required to obtain a desired level of accuracy and the associated computational times as comparison criteria.

[Applying dose banding to the production of antineoplastic drugs: a narrative review of the literature].

PubMed

Pérez Huertas, Pablo; Cueto Sola, Margarita; Escobar Cava, Paloma; Borrell García, Carmela; Albert Marí, Asunción; López Briz, Eduardo; Poveda Andrés, José Luis

2015-07-01

The dosage of antineoplastic drugs has historically been based on individualized prescription and preparation according to body surface area or patient´s weight. Lack of resources and increased assistance workload in the areas where chemotherapy is made, are leading to the development of new systems to optimize the processing without reducing safety. One of the strategies that has been proposed is the elaboration by dose banding. This new approach standardizes the antineoplastic agents doses by making ranges or bands accepting a percentage of maximum variation. It aims to reduce processing time with the consequent reduction in waiting time for patients; to reduce errors in the manufacturing process and to promote the rational drug use. In conclusion, dose banding is a suitable method for optimizing the development of anticancer drugs, obtaining reductions in oncologic patients waiting time but without actually causing a favorable impact on direct or indirect costs. Copyright AULA MEDICA EDICIONES 2014. Published by AULA MEDICA. All rights reserved.

Optimizing Interactive Development of Data-Intensive Applications

PubMed Central

Interlandi, Matteo; Tetali, Sai Deep; Gulzar, Muhammad Ali; Noor, Joseph; Condie, Tyson; Kim, Miryung; Millstein, Todd

2017-01-01

Modern Data-Intensive Scalable Computing (DISC) systems are designed to process data through batch jobs that execute programs (e.g., queries) compiled from a high-level language. These programs are often developed interactively by posing ad-hoc queries over the base data until a desired result is generated. We observe that there can be significant overlap in the structure of these queries used to derive the final program. Yet, each successive execution of a slightly modified query is performed anew, which can significantly increase the development cycle. Vega is an Apache Spark framework that we have implemented for optimizing a series of similar Spark programs, likely originating from a development or exploratory data analysis session. Spark developers (e.g., data scientists) can leverage Vega to significantly reduce the amount of time it takes to re-execute a modified Spark program, reducing the overall time to market for their Big Data applications. PMID:28405637

A "Neurological Emergency Trolley" reduces turnaround time for high-risk medications in a general intensive care unit.

PubMed

Ajzenberg, Henry; Newman, Paula; Harris, Gail-Anne; Cranston, Marnie; Boyd, J Gordon

2018-02-01

To reduce medication turnaround times during neurological emergencies, a multidisciplinary team developed a neurological emergency crash trolley in our intensive care unit. This trolley includes phenytoin, hypertonic saline and mannitol, as well as other equipment. The aim of this study was to assess whether the cart reduced turnaround times for these medications. In this retrospective cohort study, medication delivery times for two year epochs before and after its implementation were compared. Eligible patients were identified from our intensive care unit screening log. Adults who required emergent use of phenytoin, hypertonic saline or mannitol while in the intensive care unit were included. Groups were compared with nonparametric analyses. 33-bed general medical-surgical intensive care unit in an academic teaching hospital. Time to medication administration. In the pre-intervention group, there were 43 patients with 66 events. In the post-intervention group, there were 45 patients with 80 events. The median medication turnaround time was significantly reduced after implementation of the neurological emergency trolley (25 vs. 10minutes, p=0.003). There was no statistically significant difference in intensive care or 30-day survival between the two cohorts. The implementation of a novel neurological emergency crash trolley in our intensive care unit reduced medication turnaround times. Copyright © 2017 Elsevier Ltd. All rights reserved.

Developmental plasticity in Tenebrio molitor (Coleoptera: Tenebrionidae): Analysis of Instar Variation in Number and Development Time under Different Diets

USDA-ARS?s Scientific Manuscript database

The variation in instar number and the pattern of sequential instar development time of Tenebrio molitor L. (Coleoptera: Tenebrionidae) was studied under 4 different diet regimes. Addition of dietary supplements consisting of dry potato or a mix of dry potato and dry egg whites significantly reduced...

Spaceborne Hybrid-FPGA System for Processing FTIR Data

NASA Technical Reports Server (NTRS)

Bekker, Dmitriy; Blavier, Jean-Francois L.; Pingree, Paula J.; Lukowiak, Marcin; Shaaban, Muhammad

2008-01-01

Progress has been made in a continuing effort to develop a spaceborne computer system for processing readout data from a Fourier-transform infrared (FTIR) spectrometer to reduce the volume of data transmitted to Earth. The approach followed in this effort, oriented toward reducing design time and reducing the size and weight of the spectrometer electronics, has been to exploit the versatility of recently developed hybrid field-programmable gate arrays (FPGAs) to run diverse software on embedded processors while also taking advantage of the reconfigurable hardware resources of the FPGAs.

The workplace and alcohol problem prevention.

PubMed

Roman, Paul M; Blum, Terry C

2002-01-01

Workplace programs to prevent and reduce alcohol-related problems among employees have considerable potential. For example, because employees spend a lot of time at work, coworkers and supervisors may have the opportunity to notice a developing alcohol problem. In addition, employers can use their influence to motivate employees to get help for an alcohol problem. Many employers offer employee assistance programs (EAPs) as well as educational programs to reduce employees' alcohol problems. However, several risk factors for alcohol problems exist in the workplace domain. Further research is needed to develop strategies to reduce these risk factors.

Spacelab Mission Implementation Cost Assessment (SMICA)

NASA Technical Reports Server (NTRS)

Guynes, B. V.

1984-01-01

A total savings of approximately 20 percent is attainable if: (1) mission management and ground processing schedules are compressed; (2) the equipping, staffing, and operating of the Payload Operations Control Center is revised, and (3) methods of working with experiment developers are changed. The development of a new mission implementation technique, which includes mission definition, experiment development, and mission integration/operations, is examined. The Payload Operations Control Center is to relocate and utilize new computer equipment to produce cost savings. Methods of reducing costs by minimizing the Spacelab and payload processing time during pre- and post-mission operation at KSC are analyzed. The changes required to reduce costs in the analytical integration process are studied. The influence of time, requirements accountability, and risk on costs is discussed. Recommendation for cost reductions developed by the Spacelab Mission Implementation Cost Assessment study are listed.

Stand More AT Work (SMArT Work): using the behaviour change wheel to develop an intervention to reduce sitting time in the workplace.

PubMed

Munir, Fehmidah; Biddle, Stuart J H; Davies, Melanie J; Dunstan, David; Esliger, David; Gray, Laura J; Jackson, Ben R; O'Connell, Sophie E; Yates, Tom; Edwardson, Charlotte L

2018-03-06

Sitting (sedentary behaviour) is widespread among desk-based office workers and a high level of sedentary behaviour is a risk factor for poor health. Reducing workplace sitting time is therefore an important prevention strategy. Interventions are more likely to be effective if they are theory and evidence-based. The Behaviour Change Wheel (BCW) provides a framework for intervention development. This article describes the development of the Stand More AT Work (SMArT Work) intervention, which aims to reduce sitting time among National Health Service (NHS) office-based workers in Leicester, UK. We followed the BCW guide and used the Capability, Opportunity and Motivation Behaviour (COM-B) model to conduct focus group discussions with 39 NHS office workers. With these data we used the taxonomy of Behaviour Change Techniques (BCTv1) to identify the most appropriate strategies for facilitating behaviour change in our intervention. To identify the best method for participants to self-monitor their sitting time, a sub-group of participants (n = 31) tested a number of electronic self-monitoring devices. From our BCW steps and the BCT-Taxonomy we identified 10 behaviour change strategies addressing environmental (e.g. provision of height adjustable desks,), organisational (e.g. senior management support, seminar), and individual level (e.g. face-to-face coaching session) barriers. The Darma cushion scored the highest for practicality and acceptability for self-monitoring sitting. The BCW guide, COM-B model and BCT-Taxonomy can be applied successfully in the context of designing a workplace intervention for reducing sitting time through standing and moving more. The intervention was developed in collaboration with office workers (a participatory approach) to ensure relevance for them and their work situation. The effectiveness of this intervention is currently being evaluated in a randomised controlled trial. ISRCTN10967042 . Registered on 2 February 2015.

Transformative Learning and First-Time Managers: How Can HRD Practitioners Help?

ERIC Educational Resources Information Center

Roberts, Nella A.; Rocco, Tonette S.

2008-01-01

The transition to management is one of the most difficult challenges first-time managers face--almost half fail. First-time managers may experience disorienting dilemmas that trigger transformative learning. HRD (human resource development) practitioners can assist in reducing the failure rate of first-time managers when they better understand the…

TES: A modular systems approach to expert system development for real time space applications

NASA Technical Reports Server (NTRS)

England, Brenda; Cacace, Ralph

1987-01-01

A major goal of the space station era is to reduce reliance on support from ground based experts. The TIMES Expert System (TES) is an application that monitors and evaluates real time data to perform fault detection and fault isolation as it would otherwise be carried out by a knowledgeable designer. The development process and primary features of the TES, the modular system and the lessons learned are discussed.

Smart Sampling and HPC-based Probabilistic Look-ahead Contingency Analysis Implementation and its Evaluation with Real-world Data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Yousu; Etingov, Pavel V.; Ren, Huiying

This paper describes a probabilistic look-ahead contingency analysis application that incorporates smart sampling and high-performance computing (HPC) techniques. Smart sampling techniques are implemented to effectively represent the structure and statistical characteristics of uncertainty introduced by different sources in the power system. They can significantly reduce the data set size required for multiple look-ahead contingency analyses, and therefore reduce the time required to compute them. High-performance-computing (HPC) techniques are used to further reduce computational time. These two techniques enable a predictive capability that forecasts the impact of various uncertainties on potential transmission limit violations. The developed package has been tested withmore » real world data from the Bonneville Power Administration. Case study results are presented to demonstrate the performance of the applications developed.« less

Development of Automated Image Analysis Software for Suspended Marine Particle Classification

DTIC Science & Technology

2002-09-30

Development of Automated Image Analysis Software for Suspended Marine Particle Classification Scott Samson Center for Ocean Technology...and global water column. 1 OBJECTIVES The project’s objective is to develop automated image analysis software to reduce the effort and time

Post-Activity Report: DHSS Organisational Culture and Performance Workshop 2012

DTIC Science & Technology

2013-08-01

outcomes Reduced absenteeism Rate of absenteeism over time The direct measures will provide pertinent information on the observable aspects of...courage • Reduced absenteeism • Innovation is encouraged • More efficient practice Page classification: UNCLASSIFIED DEFENCE...of organisational culture, further work can then be done to develop targeted measures to monitor and reduce these critical gaps, and focus attention

Note: Real time control of a tunable vibration absorber based on magnetorheological elastomer for suppressing tonal vibrations

NASA Astrophysics Data System (ADS)

Kim, Young-Keun; Bae, Hyo-In; Koo, Jeong-Hoi; Kim, Kyung-Soo; Kim, Soohyun

2012-04-01

An adaptive tunable vibration absober based on magnetorheological elastomer (MRE) is designed as an intelligent device for auto-tuning itself to the time-varying harmonic disturbance force to reduce the unwanted vibration of the primary system in the steady state. The objectives of this note are to develop and implement a continuous control method for a MRE tunable vibration absorber (TVA) and to evaluate its performance in suppressing time-varying tonal vibrations. In the proposed control, the stiffness of MREs is continuously varied based on a nonlinear tuning function that relates the response of the system to the input magnetic field density. Through experiments, it will be shown that the proposed MRE TVA reduces in real time the transmission of a time-varying excited vibration of 48-55 Hz, which shows the potential applicability of the MRE in reducing unwanted vibration to precision devices.

Applying Reduced Generator Models in the Coarse Solver of Parareal in Time Parallel Power System Simulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duan, Nan; Dimitrovski, Aleksandar D; Simunovic, Srdjan

2016-01-01

The development of high-performance computing techniques and platforms has provided many opportunities for real-time or even faster-than-real-time implementation of power system simulations. One approach uses the Parareal in time framework. The Parareal algorithm has shown promising theoretical simulation speedups by temporal decomposing a simulation run into a coarse simulation on the entire simulation interval and fine simulations on sequential sub-intervals linked through the coarse simulation. However, it has been found that the time cost of the coarse solver needs to be reduced to fully exploit the potentials of the Parareal algorithm. This paper studies a Parareal implementation using reduced generatormore » models for the coarse solver and reports the testing results on the IEEE 39-bus system and a 327-generator 2383-bus Polish system model.« less

A Distributed Online Curriculum and Courseware Development Model

ERIC Educational Resources Information Center

Durdu, Pinar Onay; Yalabik, Nese; Cagiltay, Kursat

2009-01-01

A distributed online curriculum and courseware development model (DONC[superscript 2]) is developed and tested in this study. Courseware development teams which may work in different institutions who need to develop high quality, reduced cost, on time products will be the users of DONC[superscript 2]. The related features from the disciplines of…

Development of multilayer perceptron networks for isothermal time temperature transformation prediction of U-Mo-X alloys

NASA Astrophysics Data System (ADS)

Johns, Jesse M.; Burkes, Douglas

2017-07-01

In this work, a multilayered perceptron (MLP) network is used to develop predictive isothermal time-temperature-transformation (TTT) models covering a range of U-Mo binary and ternary alloys. The selected ternary alloys for model development are U-Mo-Ru, U-Mo-Nb, U-Mo-Zr, U-Mo-Cr, and U-Mo-Re. These model's ability to predict 'novel' U-Mo alloys is shown quite well despite the discrepancies between literature sources for similar alloys which likely arise from different thermal-mechanical processing conditions. These models are developed with the primary purpose of informing experimental decisions. Additional experimental insight is necessary in order to reduce the number of experiments required to isolate ideal alloys. These models allow test planners to evaluate areas of experimental interest; once initial tests are conducted, the model can be updated and further improve follow-on testing decisions. The model also improves analysis capabilities by reducing the number of data points necessary from any particular test. For example, if one or two isotherms are measured during a test, the model can construct the rest of the TTT curve over a wide range of temperature and time. This modeling capability reduces the cost of experiments while also improving the value of the results from the tests. The reduced costs could result in improved material characterization and therefore improved fundamental understanding of TTT dynamics. As additional understanding of phenomena driving TTTs is acquired, this type of MLP model can be used to populate unknowns (such as material impurity and other thermal mechanical properties) from past literature sources.

Traffic flow forecasting using approximate nearest neighbor nonparametric regression

DOT National Transportation Integrated Search

2000-12-01

The purpose of this research is to enhance nonparametric regression (NPR) for use in real-time systems by first reducing execution time using advanced data structures and imprecise computations and then developing a methodology for applying NPR. Due ...

A high performance load balance strategy for real-time multicore systems.

PubMed

Cho, Keng-Mao; Tsai, Chun-Wei; Chiu, Yi-Shiuan; Yang, Chu-Sing

2014-01-01

Finding ways to distribute workloads to each processor core and efficiently reduce power consumption is of vital importance, especially for real-time systems. In this paper, a novel scheduling algorithm is proposed for real-time multicore systems to balance the computation loads and save power. The developed algorithm simultaneously considers multiple criteria, a novel factor, and task deadline, and is called power and deadline-aware multicore scheduling (PDAMS). Experiment results show that the proposed algorithm can greatly reduce energy consumption by up to 54.2% and the deadline times missed, as compared to the other scheduling algorithms outlined in this paper.

A High Performance Load Balance Strategy for Real-Time Multicore Systems

PubMed Central

Cho, Keng-Mao; Tsai, Chun-Wei; Chiu, Yi-Shiuan; Yang, Chu-Sing

2014-01-01

Finding ways to distribute workloads to each processor core and efficiently reduce power consumption is of vital importance, especially for real-time systems. In this paper, a novel scheduling algorithm is proposed for real-time multicore systems to balance the computation loads and save power. The developed algorithm simultaneously considers multiple criteria, a novel factor, and task deadline, and is called power and deadline-aware multicore scheduling (PDAMS). Experiment results show that the proposed algorithm can greatly reduce energy consumption by up to 54.2% and the deadline times missed, as compared to the other scheduling algorithms outlined in this paper. PMID:24955382

Development of materials for the rapid manufacture of die cast tooling

NASA Astrophysics Data System (ADS)

Hardro, Peter Jason

The focus of this research is to develop a material composition that can be processed by rapid prototyping (RP) in order to produce tooling for the die casting process. Where these rapidly produced tools will be superior to traditional tooling production methods by offering one or more of the following advantages: reduced tooling cost, shortened tooling creation time, reduced man-hours for tool creation, increased tool life, and shortened die casting cycle time. By utilizing RP's additive build process and vast material selection, there was a prospect that die cast tooling may be produced quicker and with superior material properties. To this end, the material properties that influence die life and cycle time were determined, and a list of materials that fulfill these "optimal" properties were highlighted. Physical testing was conducted in order to grade the processability of each of the material systems and to optimize the manufacturing process for the downselected material system. Sample specimens were produced and microscopy techniques were utilized to determine a number of physical properties of the material system. Additionally, a benchmark geometry was selected and die casting dies were produced from traditional tool materials (H13 steel) and techniques (machining) and from the newly developed materials and RP techniques (selective laser sintering (SLS) and laser engineered net shaping (LENS)). Once the tools were created, a die cast alloy was selected and a preset number of parts were shot into each tool. During tool creation, the manufacturing time and cost was closely monitored and an economic model was developed to compare traditional tooling to RP tooling. This model allows one to determine, in the early design stages, when it is advantageous to implement RP tooling and when traditional tooling would be best. The results of the physical testing and economic analysis has shown that RP tooling is able to achieve a number of the research objectives, namely, reduce tooling cost, shorten tooling creation time, and reduce the man-hours needed for tool creation. Though identifying the appropriate time to use RP tooling appears to be the most important aspect in achieving successful implementation.

Shortening Delivery Times of Intensity Modulated Proton Therapy by Reducing Proton Energy Layers During Treatment Plan Optimization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Water, Steven van de, E-mail: s.vandewater@erasmusmc.nl; Kooy, Hanne M.; Heijmen, Ben J.M.

2015-06-01

Purpose: To shorten delivery times of intensity modulated proton therapy by reducing the number of energy layers in the treatment plan. Methods and Materials: We have developed an energy layer reduction method, which was implemented into our in-house-developed multicriteria treatment planning system “Erasmus-iCycle.” The method consisted of 2 components: (1) minimizing the logarithm of the total spot weight per energy layer; and (2) iteratively excluding low-weighted energy layers. The method was benchmarked by comparing a robust “time-efficient plan” (with energy layer reduction) with a robust “standard clinical plan” (without energy layer reduction) for 5 oropharyngeal cases and 5 prostate cases.more » Both plans of each patient had equal robust plan quality, because the worst-case dose parameters of the standard clinical plan were used as dose constraints for the time-efficient plan. Worst-case robust optimization was performed, accounting for setup errors of 3 mm and range errors of 3% + 1 mm. We evaluated the number of energy layers and the expected delivery time per fraction, assuming 30 seconds per beam direction, 10 ms per spot, and 400 Giga-protons per minute. The energy switching time was varied from 0.1 to 5 seconds. Results: The number of energy layers was on average reduced by 45% (range, 30%-56%) for the oropharyngeal cases and by 28% (range, 25%-32%) for the prostate cases. When assuming 1, 2, or 5 seconds energy switching time, the average delivery time was shortened from 3.9 to 3.0 minutes (25%), 6.0 to 4.2 minutes (32%), or 12.3 to 7.7 minutes (38%) for the oropharyngeal cases, and from 3.4 to 2.9 minutes (16%), 5.2 to 4.2 minutes (20%), or 10.6 to 8.0 minutes (24%) for the prostate cases. Conclusions: Delivery times of intensity modulated proton therapy can be reduced substantially without compromising robust plan quality. Shorter delivery times are likely to reduce treatment uncertainties and costs.« less

Lean Development with the Morpheus Simulation Software

NASA Technical Reports Server (NTRS)

Brogley, Aaron C.

2013-01-01

The Morpheus project is an autonomous robotic testbed currently in development at NASA's Johnson Space Center (JSC) with support from other centers. Its primary objectives are to test new 'green' fuel propulsion systems and to demonstrate the capability of the Autonomous Lander Hazard Avoidance Technology (ALHAT) sensor, provided by the Jet Propulsion Laboratory (JPL) on a lunar landing trajectory. If successful, these technologies and lessons learned from the Morpheus testing cycle may be incorporated into a landing descent vehicle used on the moon, an asteroid, or Mars. In an effort to reduce development costs and cycle time, the project employs lean development engineering practices in its development of flight and simulation software. The Morpheus simulation makes use of existing software packages where possible to reduce the development time. The development and testing of flight software occurs primarily through the frequent test operation of the vehicle and incrementally increasing the scope of the test. With rapid development cycles, risk of loss of the vehicle and loss of the mission are possible, but efficient progress in development would not be possible without that risk.

Actual Instructional Time in African Primary Schools: Factors that Reduce School Quality in Developing Countries

ERIC Educational Resources Information Center

Benavot, Aaron; Gad, Limor

2004-01-01

Educational theorists and researchers have long considered time a key component of individual learning. Caroll, in his classic model of school-based learning, conceptualized achievement as an outcome of two time variables: first, the amount of time a learner is engaged in learning; and second, an individual's learning rate. Caroll's ideas…

Algorithms and Object-Oriented Software for Distributed Physics-Based Modeling

NASA Technical Reports Server (NTRS)

Kenton, Marc A.

2001-01-01

The project seeks to develop methods to more efficiently simulate aerospace vehicles. The goals are to reduce model development time, increase accuracy (e.g.,by allowing the integration of multidisciplinary models), facilitate collaboration by geographically- distributed groups of engineers, support uncertainty analysis and optimization, reduce hardware costs, and increase execution speeds. These problems are the subject of considerable contemporary research (e.g., Biedron et al. 1999; Heath and Dick, 2000).

Do physical leisure time activities prevent fatigue? A 15 month prospective study of nurses' aides.

PubMed

Eriksen, W; Bruusgaard, D

2004-06-01

To test the hypothesis that physical leisure time activities reduce the risk of developing persistent fatigue. The hypothesis was tested in a sample that was homogeneous with respect to sex and occupation, with a prospective cohort design. Of 6234 vocationally active, female, Norwegian nurses' aides, not on leave because of illness or pregnancy when they completed a mailed questionnaire in 1999, 5341 (85.7%) completed a second questionnaire 15 months later. The main outcome measure was the prevalence of persistent fatigue-that is, always or usually feeling fatigued in the daytime during the preceding 14 days. In participants without persistent fatigue at baseline, reported engagement in physical leisure time activities for 20 minutes or more at least once a week during the three months before baseline was associated with a reduced risk of persistent fatigue at the follow up (odds ratio = 0.70; 95% confidence interval 0.55 to 0.89), after adjustments for age, affective symptoms, sleeping problems, musculoskeletal pain, long term health problems of any kind, smoking, marital status, tasks of a caring nature during leisure time, and work factors at baseline. The study supports the hypothesis that physical leisure time activities reduce the risk of developing persistent fatigue.

Infarct size in primary angioplasty without on-site cardiac surgical backup versus transferal to a tertiary center: a single photon emission computed tomography study.

PubMed

Knaapen, Paul; de Mulder, Maarten; van der Zant, Friso M; Peels, Hans O; Twisk, Jos W R; van Rossum, Albert C; Cornel, Jan H; Umans, Victor A W M

2009-02-01

Primary percutaneous coronary intervention (PCI) performed in large community hospitals without cardiac surgery back-up facilities (off-site) reduces door-to-balloon time compared with emergency transferal to tertiary interventional centers (on-site). The present study was performed to explore whether off-site PCI for acute myocardial infarction results in reduced infarct size. One hundred twenty-eight patients with acute ST-segment elevation myocardial infarction were randomly assigned to undergo primary PCI at the off-site center (n = 68) or to transferal to an on-site center (n = 60). Three days after PCI, (99m)Tc-sestamibi SPECT was performed to estimate infarct size. Off-site PCI significantly reduced door-to-balloon time compared with on-site PCI (94 +/- 54 versus 125 +/- 59 min, respectively, p < 0.01), although symptoms-to-treatment time was only insignificantly reduced (257 +/- 211 versus 286 +/- 146 min, respectively, p = 0.39). Infarct size was comparable between treatment centers (16 +/- 15 versus 14 +/- 12%, respectively p = 0.35). Multivariate analysis revealed that TIMI 0/1 flow grade at initial coronary angiography (OR 3.125, 95% CI 1.17-8.33, p = 0.023), anterior wall localization of the myocardial infarction (OR 3.44, 95% CI 1.38-8.55, p < 0.01), and development of pathological Q-waves (OR 5.07, 95% CI 2.10-12.25, p < 0.01) were independent predictors of an infarct size > 12%. Off-site PCI reduces door-to-balloon time compared with transferal to a remote on-site interventional center but does not reduce infarct size. Instead, pre-PCI TIMI 0/1 flow, anterior wall infarct localization, and development of Q-waves are more important predictors of infarct size.

Adolescent Sedentary Behaviors: Correlates Differ for Television Viewing and Computer Use

PubMed Central

Babey, Susan H.; Hastert, Theresa A.; Wolstein, Joelle

2013-01-01

Purpose Sedentary behavior is associated with obesity in youth. Understanding correlates of specific sedentary behaviors can inform the development of interventions to reduce sedentary time. The current research examines correlates of leisure computer use and television viewing among California adolescents. Methods Using data from the 2005 California Health Interview Survey (CHIS), we examined individual, family and environmental correlates of two sedentary behaviors among 4,029 adolescents: leisure computer use and television watching. Results Linear regression analyses adjusting for a range of factors indicated several differences in the correlates of television watching and computer use. Correlates of additional time spent watching television included male sex, American Indian and African American race, lower household income, lower levels of physical activity, lower parent educational attainment, and additional hours worked by parents. Correlates of a greater amount of time spent using the computer for fun included older age, Asian race, higher household income, lower levels of physical activity, less parental knowledge of free time activities, and living in neighborhoods with higher proportions of non-white residents and higher proportions of low-income residents. Only physical activity was associated similarly with both watching television and computer use. Conclusions These results suggest that correlates of time spent on television watching and leisure computer use are different. Reducing screen time is a potentially successful strategy in combating childhood obesity, and understanding differences in the correlates of different screen time behaviors can inform the development of more effective interventions to reduce sedentary time. PMID:23260837

Development of WRF-ROI system by incorporating eigen-decomposition

NASA Astrophysics Data System (ADS)

Kim, S.; Noh, N.; Song, H.; Lim, G.

2011-12-01

This study presents the development of WRF-ROI system, which is the implementation of Retrospective Optimal Interpolation (ROI) to the Weather Research and Forecasting model (WRF). ROI is a new data assimilation algorithm introduced by Song et al. (2009) and Song and Lim (2009). The formulation of ROI is similar with that of Optimal Interpolation (OI), but ROI iteratively assimilates an observation set at a post analysis time into a prior analysis, possibly providing the high quality reanalysis data. ROI method assimilates the data at post analysis time using perturbation method (Errico and Raeder, 1999) without adjoint model. In previous study, ROI method is applied to Lorenz 40-variable model (Lorenz, 1996) to validate the algorithm and to investigate the capability. It is therefore required to apply this ROI method into a more realistic and complicated model framework such as WRF. In this research, the reduced-rank formulation of ROI is used instead of a reduced-resolution method. The computational costs can be reduced due to the eigen-decomposition of background error covariance in the reduced-rank method. When single profile of observations is assimilated in the WRF-ROI system by incorporating eigen-decomposition, the analysis error tends to be reduced if compared with the background error. The difference between forecast errors with assimilation and without assimilation is obviously increased as time passed, which means the improvement of forecast error by assimilation.

Stimulation of a turbofan engine for evaluation of multivariable optimal control concepts. [(computerized simulation)

NASA Technical Reports Server (NTRS)

Seldner, K.

1976-01-01

The development of control systems for jet engines requires a real-time computer simulation. The simulation provides an effective tool for evaluating control concepts and problem areas prior to actual engine testing. The development and use of a real-time simulation of the Pratt and Whitney F100-PW100 turbofan engine is described. The simulation was used in a multi-variable optimal controls research program using linear quadratic regulator theory. The simulation is used to generate linear engine models at selected operating points and evaluate the control algorithm. To reduce the complexity of the design, it is desirable to reduce the order of the linear model. A technique to reduce the order of the model; is discussed. Selected results between high and low order models are compared. The LQR control algorithms can be programmed on digital computer. This computer will control the engine simulation over the desired flight envelope.

Torching the Haystack: modelling fast-fail strategies in drug development.

PubMed

Lendrem, Dennis W; Lendrem, B Clare

2013-04-01

By quickly clearing the development pipeline of failing or marginal products, fast-fail strategies release resources to focus on more promising molecules. The Quick-Kill model of drug development demonstrates that fast-fail strategies will: (1) reduce the expected time to market; (2) reduce expected R&D costs; and (3) increase R&D productivity. This paper outlines the model and demonstrates the impact of fast-fail strategies. The model is illustrated with costs and risks data from pharmaceutical and biopharmaceutical companies. Copyright © 2012 Elsevier Ltd. All rights reserved.

Reductive amination of tertiary anilines and aldehydes.

PubMed

Lv, Yunhe; Zheng, Yiying; Li, Yan; Xiong, Tao; Zhang, Jingping; Liu, Qun; Zhang, Qian

2013-10-09

An unprecedented oxidant-mediated reductive amination of tertiary anilines and aldehydes without external reducing agents was developed via the nucleophilic attack of the oxygen atom of the carbonyl group to in situ generated iminium ions, in which tertiary anilines were used as both nitrogen source and reducing agent for the first time.

Automated Sample Exchange Robots for the Structural Biology Beam Lines at the Photon Factory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hiraki, Masahiko; Watanabe, Shokei; Yamada, Yusuke

2007-01-19

We are now developing automated sample exchange robots for high-throughput protein crystallographic experiments for onsite use at synchrotron beam lines. It is part of the fully automated robotics systems being developed at the Photon Factory, for the purposes of protein crystallization, monitoring crystal growth, harvesting and freezing crystals, mounting the crystals inside a hutch and for data collection. We have already installed the sample exchange robots based on the SSRL automated mounting system at our insertion device beam lines BL-5A and AR-NW12A at the Photon Factory. In order to reduce the time required for sample exchange further, a prototype ofmore » a double-tonged system was developed. As a result of preliminary experiments with double-tonged robots, the sample exchange time was successfully reduced from 70 seconds to 10 seconds with the exception of the time required for pre-cooling and warming up the tongs.« less

Risk-reducing surgery on the uterine adnexa: timing and type of surgical treatment, and pathology report.

PubMed

Signorelli, Mauro; Bogani, Giorgio; Ditto, Antonino; Martinelli, Fabio; Chiappa, Valentina; Lopez, Carlos; Scaffa, Cono; Lorusso, Domenica; Raspagliesi, Francesco

2016-10-01

Inherited mutations in BRCA1 and BRCA2 increase significantly the risk of developing breast and ovarian cancers, and they have been associated with increased risks of developing other types of cancer. Although screening programs have been implemented in order to detect cancers at the early stage, they resulted ineffective. To date, risk-reducing bilateral salpingo-oophorectomy represents the only procedure allowing reducing the incidence of ovarian cancer and increasing survival among BRCA1 and -2 mutation carriers. In the present review we will discuss the advantages and disadvantages related to the execution of prophylactic surgery, thus underlying possible beneficial and detrimental effects of this kind of surgery in premenopausal women. Additionally, we will investigate further therapeutic strategies aimed to reduce the risk of developing ovarian cancer, without affected patients' hormonal status.

Recent National Transonic Facility Test Process Improvements (Invited)

NASA Technical Reports Server (NTRS)

Kilgore, W. A.; Balakrishna, S.; Bobbitt, C. W., Jr.; Adcock, J. B.

2001-01-01

This paper describes the results of two recent process improvements; drag feed-forward Mach number control and simultaneous force/moment and pressure testing, at the National Transonic Facility. These improvements have reduced the duration and cost of testing. The drag feed-forward Mach number control reduces the Mach number settling time by using measured model drag in the Mach number control algorithm. Simultaneous force/moment and pressure testing allows simultaneous collection of force/moment and pressure data without sacrificing data quality thereby reducing the overall testing time. Both improvements can be implemented at any wind tunnel. Additionally the NTF is working to develop and implement continuous pitch as a testing option as an additional method to reduce costs and maintain data quality.

Recent National Transonic Facility Test Process Improvements (Invited)

NASA Technical Reports Server (NTRS)

Kilgore, W. A.; Balakrishna, S.; Bobbitt, C. W., Jr.; Adcock, J. B.

2001-01-01

This paper describes the results of two recent process improvements; drag feed-forward Mach number control and simultaneous force/moment and pressure testing, at the National Transonic Facility. These improvements have reduced the duration and cost of testing. The drag feedforward Mach number control reduces the Mach number settling time by using measured model drag in the Mach number control algorithm. Simultaneous force/moment and pressure testing allows simultaneous collection of force/moment and pressure data without sacrificing data quality thereby reducing the overall testing time. Both improvements can be implemented at any wind tunnel. Additionally the NTF is working to develop and implement continuous pitch as a testing option as an additional method to reduce costs and maintain data quality.

Circulating microparticle levels are reduced in patients with ARDS.

PubMed

Shaver, Ciara M; Woods, Justin; Clune, Jennifer K; Grove, Brandon S; Wickersham, Nancy E; McNeil, J Brennan; Shemancik, Gregory; Ware, Lorraine B; Bastarache, Julie A

2017-05-25

It is unclear how to identify which patients at risk for acute respiratory distress syndrome (ARDS) will develop this condition during critical illness. Elevated microparticle (MP) concentrations in the airspace during ARDS are associated with activation of coagulation and in vitro studies have demonstrated that MPs contribute to acute lung injury, but the significance of MPs in the circulation during ARDS has not been well studied. The goal of the present study was to test the hypothesis that elevated levels of circulating MPs could prospectively identify critically ill patients who will develop ARDS and that elevated circulating MPs are associated with poor clinical outcomes. A total of 280 patients with platelet-poor plasma samples from the prospective Validating Acute Lung Injury biomarkers for Diagnosis (VALID) cohort study were selected for this analysis. Demographics and clinical data were obtained by chart review. MP concentrations in plasma were measured at study enrollment on intensive care unit (ICU) day 2 and on ICU day 4 by MP capture assay. Activation of coagulation was measured by plasma recalcification (clot) times. ARDS developed in 90 of 280 patients (32%) in the study. Elevated plasma MP concentrations were associated with reduced risk of developing ARDS (odds ratio (OR) 0.70 per 10 μM increase in MP concentration, 95% CI 0.50-0.98, p = 0.042), but had no significant effect on hospital mortality. MP concentration was greatest in patients with sepsis, pneumonia, or aspiration as compared with those with trauma or receiving multiple blood transfusions. MP levels did not significantly change over time. The inverse association of MP levels with ARDS development was most striking in patients with sepsis. After controlling for age, presence of sepsis, and severity of illness, higher MP concentrations were independently associated with a reduced risk of developing ARDS (OR 0.69, 95% CI 0.49-0.98, p = 0.038). MP concentration was associated with reduced plasma recalcification time. Elevated levels of circulating MPs are independently associated with a reduced risk of ARDS in critically ill patients. Whether this is due to MP effects on systemic coagulation warrants further investigation.

Fast Learning for Immersive Engagement in Energy Simulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bush, Brian W; Bugbee, Bruce; Gruchalla, Kenny M

The fast computation which is critical for immersive engagement with and learning from energy simulations would be furthered by developing a general method for creating rapidly computed simplified versions of NREL's computation-intensive energy simulations. Created using machine learning techniques, these 'reduced form' simulations can provide statistically sound estimates of the results of the full simulations at a fraction of the computational cost with response times - typically less than one minute of wall-clock time - suitable for real-time human-in-the-loop design and analysis. Additionally, uncertainty quantification techniques can document the accuracy of the approximate models and their domain of validity. Approximationmore » methods are applicable to a wide range of computational models, including supply-chain models, electric power grid simulations, and building models. These reduced-form representations cannot replace or re-implement existing simulations, but instead supplement them by enabling rapid scenario design and quality assurance for large sets of simulations. We present an overview of the framework and methods we have implemented for developing these reduced-form representations.« less

Optimization of a protocol for myocardial perfusion scintigraphy by using an anthropomorphic phantom.

PubMed

Ramos, Susie Medeiros Oliveira; Glavam, Adriana Pereira; Kubo, Tadeu Takao Almodovar; de Sá, Lidia Vasconcellos

2014-01-01

To develop a study aiming at optimizing myocardial perfusion imaging. Imaging of an anthropomorphic thorax phantom with a GE SPECT Ventri gamma camera, with varied activities and acquisition times, in order to evaluate the influence of these parameters on the quality of the reconstructed medical images. The (99m)Tc-sestamibi radiotracer was utilized, and then the images were clinically evaluated on the basis of data such as summed stress score, and on the technical image quality and perfusion. The software ImageJ was utilized in the data quantification. The results demonstrated that for the standard acquisition time utilized in the procedure (15 seconds per angle), the injected activity could be reduced by 33.34%. Additionally, even if the standard scan time is reduced by 53.34% (7 seconds per angle), the standard injected activity could still be reduced by 16.67%, without impairing the image quality and the diagnostic reliability. The described method and respective results provide a basis for the development of a clinical trial of patients in an optimized protocol.

Optimization of a protocol for myocardial perfusion scintigraphy by using an anthropomorphic phantom*

PubMed Central

Ramos, Susie Medeiros Oliveira; Glavam, Adriana Pereira; Kubo, Tadeu Takao Almodovar; de Sá, Lidia Vasconcellos

2014-01-01

Objective To develop a study aiming at optimizing myocardial perfusion imaging. Materials and Methods Imaging of an anthropomorphic thorax phantom with a GE SPECT Ventri gamma camera, with varied activities and acquisition times, in order to evaluate the influence of these parameters on the quality of the reconstructed medical images. The 99mTc-sestamibi radiotracer was utilized, and then the images were clinically evaluated on the basis of data such as summed stress score, and on the technical image quality and perfusion. The software ImageJ was utilized in the data quantification. Results The results demonstrated that for the standard acquisition time utilized in the procedure (15 seconds per angle), the injected activity could be reduced by 33.34%. Additionally, even if the standard scan time is reduced by 53.34% (7 seconds per angle), the standard injected activity could still be reduced by 16.67%, without impairing the image quality and the diagnostic reliability. Conclusion The described method and respective results provide a basis for the development of a clinical trial of patients in an optimized protocol. PMID:25741088

Providing NHS staff with height-adjustable workstations and behaviour change strategies to reduce workplace sitting time: protocol for the Stand More AT (SMArT) Work cluster randomised controlled trial.

PubMed

O'Connell, S E; Jackson, B R; Edwardson, C L; Yates, T; Biddle, S J H; Davies, M J; Dunstan, D; Esliger, D; Gray, L; Miller, P; Munir, F

2015-12-09

High levels of sedentary behaviour (i.e., sitting) are a risk factor for poor health. With high levels of sitting widespread in desk-based office workers, office workplaces are an appropriate setting for interventions aimed at reducing sedentary behaviour. This paper describes the development processes and proposed intervention procedures of Stand More AT (SMArT) Work, a multi-component randomised control (RCT) trial which aims to reduce occupational sitting time in desk-based office workers within the National Health Service (NHS). SMArT Work consists of 2 phases: 1) intervention development: The development of the SMArT Work intervention takes a community-based participatory research approach using the Behaviour Change Wheel. Focus groups will collect detailed information to gain a better understanding of the most appropriate strategies, to sit alongside the provision of height-adjustable workstations, at the environmental, organisational and individual level that support less occupational sitting. 2) intervention delivery and evaluation: The 12 month cluster RCT aims to reduce workplace sitting in the University Hospitals of Leicester NHS Trust. Desk-based office workers (n = 238) will be randomised to control or intervention clusters, with the intervention group receiving height-adjustable workstations and supporting techniques based on the feedback received from the development phase. Data will be collected at four time points; baseline, 3, 6 and 12 months. The primary outcome is a reduction in sitting time, measured by the activPAL(TM) micro at 12 months. Secondary outcomes include objectively measured physical activity and a variety of work-related health and psycho-social measures. A process evaluation will also take place. This study will be the first long-term, evidence-based, multi-component cluster RCT aimed at reducing occupational sitting within the NHS. This study will help form a better understanding and knowledge base of facilitators and barriers to creating a healthier work environment and contribute to health and wellbeing policy. ISRCTN10967042 . Registered 2 February 2015.

Flight Vehicle Development Time and Cost Reduction: Conference Proceedings Held at the Flight Mechanics Panel Symposium in Toulouse (France) on 11-14 May 1987

DTIC Science & Technology

1987-09-01

appropriate because the capabilities of the vehicles are also increasing. But the perception is that time and especially the cost of the new systems...meeting was successful in focusing attention on the situation, showing what our technologies can do to reduce development time and cost growth. and by...typical program contains almost the inverse of each of these. Nonetheless, these are the areas currently receiving increased attention within the US

Real-time speech encoding based on Code-Excited Linear Prediction (CELP)

NASA Technical Reports Server (NTRS)

Leblanc, Wilfrid P.; Mahmoud, S. A.

1988-01-01

This paper reports on the work proceeding with regard to the development of a real-time voice codec for the terrestrial and satellite mobile radio environments. The codec is based on a complexity reduced version of code-excited linear prediction (CELP). The codebook search complexity was reduced to only 0.5 million floating point operations per second (MFLOPS) while maintaining excellent speech quality. Novel methods to quantize the residual and the long and short term model filters are presented.

Risk, Issues and Lessons Learned: Maximizing Risk Management in the DoD Ground Domain

DTIC Science & Technology

2011-10-01

Carnegie Mellon University “Risk Management Overview for TACOM” Benefits of Risk Management include: • Risk is a proactive approach - preventing... Chili (no beans) 13 • Hot dog sub-assy Unclassified How does the FMEA work? Execute the analysis and discover the potential failures and effects...34 - --· . -· A c u i.rition Benefits of FMEAs • Prevent major risks, reduce failures, minimize cost and reduce development time - Do it right the first time

An improved APU for the Space Shuttle Orbiter

NASA Technical Reports Server (NTRS)

Mckenna, R.; Hagemann, D.; Loken, G.; Jonakin, J.; Baughman, J.

1985-01-01

The Space Shuttle Orbiter Auxiliary Power Unit has operated successfully on all four orbiter vehicles and all missions. The current Auxiliary Power Unit (APU) operational life is limited to 12 missions, and the APU turnaround time between flights is longer than originally anticipated. The objective of the Improved APU program is to increase life to 50 missions, reduce installed vehicle weight by 134 lb., and reduce turnaround time. This paper describes the design changes incorporated into the improved APU and the associated development testing.

SU-E-T-266: Development of Evaluation System of Optimal Synchrotron Controlling Parameter for Spot Scanning Proton Therapy with Multiple Gate Irradiations in One Operation Cycle

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yamada, T; Fujii, Y; Hitachi Ltd., Hitachi-shi, Ibaraki

2015-06-15

Purpose: We have developed a gated spot scanning proton beam therapy system with real-time tumor-tracking. This system has the ability of multiple-gated irradiation in a single synchrotron operation cycle controlling the wait-time for consecutive gate signals during a flat-top phase so that the decrease in irradiation efficiency induced by irregular variation of gate signal is reduced. Our previous studies have shown that a 200 ms wait-time is appropriate to increase the average irradiation efficiency, but the optimal wait-time can vary patient by patient and day by day. In this research, we have developed an evaluation system of the optimal wait-timemore » in each irradiation based on the log data of the real-time-image gated proton beam therapy (RGPT) system. Methods: The developed system consists of logger for operation of RGPT system and software for evaluation of optimal wait-time. The logger records timing of gate on/off, timing and the dose of delivered beam spots, beam energy and timing of X-ray irradiation. The evaluation software calculates irradiation time in the case of different wait-time by simulating the multiple-gated irradiation operation using several timing information. Actual data preserved in the log data are used for gate on and off time, spot irradiation time, and time moving to the next spot. Design values are used for the acceleration and deceleration times. We applied this system to a patient treated with the RGPT system. Results: The evaluation system found the optimal wait-time of 390 ms that reduced the irradiation time by about 10 %. The irradiation time with actual wait-time used in treatment was reproduced with accuracy of 0.2 ms. Conclusion: For spot scanning proton therapy system with multiple-gated irradiation in one synchrotron operation cycle, an evaluation system of the optimal wait-time in each irradiation based on log data has been developed. Funding Support: Japan Society for the Promotion of Science (JSPS) through the FIRST Program.« less

Systematic Alternatives to Proposal Preparation.

ERIC Educational Resources Information Center

Knirk, Frederick G.; And Others

Educators who have to develop proposals must be concerned with making effective decisions. This paper discusses a number of educational systems management tools which can be used to reduce the time and effort in developing a proposal. In addition, ways are introduced to systematically increase the quality of the proposal through the development of…

Systems, methods and apparatus for generation and verification of policies in autonomic computing systems

NASA Technical Reports Server (NTRS)

Rouff, Christopher A. (Inventor); Sterritt, Roy (Inventor); Truszkowski, Walter F. (Inventor); Hinchey, Michael G. (Inventor); Gracanin, Denis (Inventor); Rash, James L. (Inventor)

2011-01-01

Described herein is a method that produces fully (mathematically) tractable development of policies for autonomic systems from requirements through to code generation. This method is illustrated through an example showing how user formulated policies can be translated into a formal mode which can then be converted to code. The requirements-based programming method described provides faster, higher quality development and maintenance of autonomic systems based on user formulation of policies.Further, the systems, methods and apparatus described herein provide a way of analyzing policies for autonomic systems and facilities the generation of provably correct implementations automatically, which in turn provides reduced development time, reduced testing requirements, guarantees of correctness of the implementation with respect to the policies specified at the outset, and provides a higher degree of confidence that the policies are both complete and reasonable. The ability to specify the policy for the management of a system and then automatically generate an equivalent implementation greatly improves the quality of software, the survivability of future missions, in particular when the system will operate untended in very remote environments, and greatly reduces development lead times and costs.

Reducing Staphylococcus aureus biofilm formation on stainless steel 316L using functionalized self-assembled monolayers

PubMed Central

Kruszewski, Kristen M; Nistico, Laura; Longwell, Mark J; Hynes, Matthew J; Maurer, Joshua A

2013-01-01

Stainless steel 316L (SS316L) is a common material used in orthopedic implants. Bacterial colonization of the surface and subsequent biofilm development can lead to refractory infection of the implant. Since the greatest risk of infection occurs perioperatively, strategies that reduce bacterial adhesion during this time are important. As a strategy to limit bacterial adhesion and biofilm formation on SS316L, self-assembled monolayers (SAMs) were used to modify the SS316L surface. SAMs with long alkyl chains terminated with hydrophobic (-CH3) or hydrophilic (oligoethylene glycol) tail groups were used to form coatings and in an orthogonal approach, SAMs were used to immobilize gentamicin or vancomycin on SS316L for the first time to form an “active” antimicrobial coating to inhibit early biofilm development. Modified SS316L surfaces were characterized using surface infrared spectroscopy, contact angles, MALDI-TOF mass spectrometry and atomic force microscopy. The ability of SAM-modified SS316L to retard biofilm development by Staphylococcus aureus was functionally tested using confocal scanning laser microscopy with COMSTAT image analysis, scanning electron microscopy and colony forming unit analysis. Neither hydrophobic nor hydrophilic SAMs reduced biofilm development. However, gentamicin-linked and vancomycin-linked SAMs significantly reduced S. aureus biofilm formation for up to 24 and 48 hours, respectively. PMID:23498233

Reducing Staphylococcus aureus biofilm formation on stainless steel 316L using functionalized self-assembled monolayers.

PubMed

Kruszewski, Kristen M; Nistico, Laura; Longwell, Mark J; Hynes, Matthew J; Maurer, Joshua A; Hall-Stoodley, Luanne; Gawalt, Ellen S

2013-05-01

Stainless steel 316L (SS316L) is a common material used in orthopedic implants. Bacterial colonization of the surface and subsequent biofilm development can lead to refractory infection of the implant. Since the greatest risk of infection occurs perioperatively, strategies that reduce bacterial adhesion during this time are important. As a strategy to limit bacterial adhesion and biofilm formation on SS316L, self-assembled monolayers (SAMs) were used to modify the SS316L surface. SAMs with long alkyl chains terminated with hydrophobic (-CH3) or hydrophilic (oligoethylene glycol) tail groups were used to form coatings and in an orthogonal approach, SAMs were used to immobilize gentamicin or vancomycin on SS316L for the first time to form an "active" antimicrobial coating to inhibit early biofilm development. Modified SS316L surfaces were characterized using surface infrared spectroscopy, contact angles, MALDI-TOF mass spectrometry and atomic force microscopy. The ability of SAM-modified SS316L to retard biofilm development by Staphylococcus aureus was functionally tested using confocal scanning laser microscopy with COMSTAT image analysis, scanning electron microscopy and colony forming unit analysis. Neither hydrophobic nor hydrophilic SAMs reduced biofilm development. However, gentamicin-linked and vancomycin-linked SAMs significantly reduced S. aureus biofilm formation for up to 24 and 48 h, respectively. Copyright © 2013 Elsevier B.V. All rights reserved.

Time-Dependent Density Functional Theory for Open Systems and Its Applications.

PubMed

Chen, Shuguang; Kwok, YanHo; Chen, GuanHua

2018-02-20

Photovoltaic devices, electrochemical cells, catalysis processes, light emitting diodes, scanning tunneling microscopes, molecular electronics, and related devices have one thing in common: open quantum systems where energy and matter are not conserved. Traditionally quantum chemistry is confined to isolated and closed systems, while quantum dissipation theory studies open quantum systems. The key quantity in quantum dissipation theory is the reduced system density matrix. As the reduced system density matrix is an O(M! × M!) matrix, where M is the number of the particles of the system of interest, quantum dissipation theory can only be employed to simulate systems of a few particles or degrees of freedom. It is thus important to combine quantum chemistry and quantum dissipation theory so that realistic open quantum systems can be simulated from first-principles. We have developed a first-principles method to simulate the dynamics of open electronic systems, the time-dependent density functional theory for open systems (TDDFT-OS). Instead of the reduced system density matrix, the key quantity is the reduced single-electron density matrix, which is an N × N matrix where N is the number of the atomic bases of the system of interest. As the dimension of the key quantity is drastically reduced, the TDDFT-OS can thus be used to simulate the dynamics of realistic open electronic systems and efficient numerical algorithms have been developed. As an application, we apply the method to study how quantum interference develops in a molecular transistor in time domain. We include electron-phonon interaction in our simulation and show that quantum interference in the given system is robust against nuclear vibration not only in the steady state but also in the transient dynamics. As another application, by combining TDDFT-OS with Ehrenfest dynamics, we study current-induced dissociation of water molecules under scanning tunneling microscopy and follow its time dependent dynamics. Given the rapid development in ultrafast experiments with atomic resolution in recent years, time dependent simulation of open electronic systems will be useful to gain insight and understanding of such experiments. This Account will mainly focus on the practical aspects of the TDDFT-OS method, describing the numerical implementation and demonstrating the method with applications.

Sensitive high-throughput screening for the detection of reducing sugars.

PubMed

Mellitzer, Andrea; Glieder, Anton; Weis, Roland; Reisinger, Christoph; Flicker, Karlheinz

2012-01-01

The exploitation of renewable resources for the production of biofuels relies on efficient processes for the enzymatic hydrolysis of lignocellulosic materials. The development of enzymes and strains for these processes requires reliable and fast activity-based screening assays. Additionally, these assays are also required to operate on the microscale and on the high-throughput level. Herein, we report the development of a highly sensitive reducing-sugar assay in a 96-well microplate screening format. The assay is based on the formation of osazones from reducing sugars and para-hydroxybenzoic acid hydrazide. By using this sensitive assay, the enzyme loads and conversion times during lignocellulose hydrolysis can be reduced, thus allowing higher throughput. The assay is about five times more sensitive than the widely applied dinitrosalicylic acid based assay and can reliably detect reducing sugars down to 10 μM. The assay-specific variation over one microplate was determined for three different lignocellulolytic enzymes and ranges from 2 to 8%. Furthermore, the assay was combined with a microscale cultivation procedure for the activity-based screening of Pichia pastoris strains expressing functional Thermomyces lanuginosus xylanase A, Trichoderma reesei β-mannanase, or T. reesei cellobiohydrolase 2. © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

TU-D-201-06: HDR Plan Prechecks Using Eclipse Scripting API

DOE Office of Scientific and Technical Information (OSTI.GOV)

Palaniswaamy, G; Morrow, A; Kim, S

Purpose: Automate brachytherapy treatment plan quality check using Eclipse v13.6 scripting API based on pre-configured rules to minimize human error and maximize efficiency. Methods: The HDR Precheck system is developed based on a rules-driven approach using Eclipse scripting API. This system checks for critical plan parameters like channel length, first source position, source step size and channel mapping. The planned treatment time is verified independently based on analytical methods. For interstitial or SAVI APBI treatment plans, a Patterson-Parker system calculation is performed to verify the planned treatment time. For endobronchial treatments, an analytical formula from TG-59 is used. Acceptable tolerancesmore » were defined based on clinical experiences in our department. The system was designed to show PASS/FAIL status levels. Additional information, if necessary, is indicated appropriately in a separate comments field in the user interface. Results: The HDR Precheck system has been developed and tested to verify the treatment plan parameters that are routinely checked by the clinical physicist. The report also serves as a reminder or checklist for the planner to perform any additional critical checks such as applicator digitization or scenarios where the channel mapping was intentionally changed. It is expected to reduce the current manual plan check time from 15 minutes to <1 minute. Conclusion: Automating brachytherapy plan prechecks significantly reduces treatment plan precheck time and reduces human errors. When fully developed, this system will be able to perform TG-43 based second check of the treatment planning system’s dose calculation using random points in the target and critical structures. A histogram will be generated along with tabulated mean and standard deviation values for each structure. A knowledge database will also be developed for Brachyvision plans which will then be used for knowledge-based plan quality checks to further reduce treatment planning errors and increase confidence in the planned treatment.« less

Development of real time abdominal compression force monitoring and visual biofeedback system

NASA Astrophysics Data System (ADS)

Kim, Tae-Ho; Kim, Siyong; Kim, Dong-Su; Kang, Seong-Hee; Cho, Min-Seok; Kim, Kyeong-Hyeon; Shin, Dong-Seok; Suh, Tae-Suk

2018-03-01

In this study, we developed and evaluated a system that could monitor abdominal compression force (ACF) in real time and provide a surrogating signal, even under abdominal compression. The system could also provide visual-biofeedback (VBF). The real-time ACF monitoring system developed consists of an abdominal compression device, an ACF monitoring unit and a control system including an in-house ACF management program. We anticipated that ACF variation information caused by respiratory abdominal motion could be used as a respiratory surrogate signal. Four volunteers participated in this test to obtain correlation coefficients between ACF variation and tidal volumes. A simulation study with another group of six volunteers was performed to evaluate the feasibility of the proposed system. In the simulation, we investigated the reproducibility of the compression setup and proposed a further enhanced shallow breathing (ESB) technique using VBF by intentionally reducing the amplitude of the breathing range under abdominal compression. The correlation coefficient between the ACF variation caused by the respiratory abdominal motion and the tidal volume signal for each volunteer was evaluated and R 2 values ranged from 0.79 to 0.84. The ACF variation was similar to a respiratory pattern and slight variations of ACF ranges were observed among sessions. About 73-77% average ACF control rate (i.e. compliance) over five trials was observed in all volunteer subjects except one (64%) when there was no VBF. The targeted ACF range was intentionally reduced to achieve ESB for VBF simulation. With VBF, in spite of the reduced target range, overall ACF control rate improved by about 20% in all volunteers except one (4%), demonstrating the effectiveness of VBF. The developed monitoring system could help reduce the inter-fraction ACF set up error and the intra fraction ACF variation. With the capability of providing a real time surrogating signal and VBF under compression, it could improve the quality of respiratory tumor motion management in abdominal compression radiation therapy.

Association of iatrogenic hypothyroidism with azotemia and reduced survival time in cats treated for hyperthyroidism.

PubMed

Williams, T L; Elliott, J; Syme, H M

2010-01-01

Iatrogenic hypothyroidism can occur after treatment of hyperthyroidism, and is correlated with a reduced glomerular filtration rate in humans and dogs. Cats with iatrogenic hypothyroidism after treatment for hyperthyroidism will have a greater incidence of azotemia than euthyroid cats. Eighty client owned cats with hyperthyroidism. Two retrospective studies. (1) Longitudinal study of 12 hyperthyroid cats treated with radioiodine (documented as euthyroid after treatment), to assess changes in plasma thyroid stimulating hormone (TSH) concentration over a 6-month follow-up period, (2) Cross-sectional study of 75 hyperthyroid cats (documented as euthyroid) 6 months after commencement of treatment for hyperthyroidism to identify the relationship between thyroid status and the development of azotemia. Kaplan-Meier survival analysis was performed to identify relationships between thyroid and renal status and survival. Plasma TSH concentrations were not suppressed in 7 of 8 cats with hypothyroidism 3 months after radioiodine treatment. The proportion of cats with azotemia was significantly (P= .028) greater in the hypothyroid (16 of 28) than the euthyroid group (14 of 47). Twenty-eight of 41 cats (68%) with plasma TT4 concentration below the laboratory reference range had an increased plasma TSH concentration. Hypothyroid cats that developed azotemia within the follow-up period had significantly (P= .018) shorter survival times (median survival time 456 days, range 231-1589 days) than those that remained nonazotemic (median survival time 905 days, range 316-1869 days). Iatrogenic hypothyroidism appears to contribute to the development of azotemia after treatment of hyperthyroidism, and reduced survival time in azotemic cats. Copyright © 2010 by the American College of Veterinary Internal Medicine.

Reducing the Time and Cost of Testing Engines

NASA Technical Reports Server (NTRS)

2004-01-01

Producing a new aircraft engine currently costs approximately $1 billion, with 3 years of development time for a commercial engine and 10 years for a military engine. The high development time and cost make it extremely difficult to transition advanced technologies for cleaner, quieter, and more efficient new engines. To reduce this time and cost, NASA created a vision for the future where designers would use high-fidelity computer simulations early in the design process in order to resolve critical design issues before building the expensive engine hardware. To accomplish this vision, NASA's Glenn Research Center initiated a collaborative effort with the aerospace industry and academia to develop its Numerical Propulsion System Simulation (NPSS), an advanced engineering environment for the analysis and design of aerospace propulsion systems and components. Partners estimate that using NPSS has the potential to dramatically reduce the time, effort, and expense necessary to design and test jet engines by generating sophisticated computer simulations of an aerospace object or system. These simulations will permit an engineer to test various design options without having to conduct costly and time-consuming real-life tests. By accelerating and streamlining the engine system design analysis and test phases, NPSS facilitates bringing the final product to market faster. NASA's NPSS Version (V)1.X effort was a task within the Agency s Computational Aerospace Sciences project of the High Performance Computing and Communication program, which had a mission to accelerate the availability of high-performance computing hardware and software to the U.S. aerospace community for its use in design processes. The technology brings value back to NASA by improving methods of analyzing and testing space transportation components.

Development of multilayer perceptron networks for isothermal time temperature transformation prediction of U-Mo-X alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johns, Jesse M.; Burkes, Douglas

In this work, a multilayered perceptron (MLP) network is used to develop predictive isothermal time-temperature-transformation (TTT) models covering a range of U-Mo binary and ternary alloys. The selected ternary alloys for model development are U-Mo-Ru, U-Mo-Nb, U-Mo-Zr, U-Mo-Cr, and U-Mo-Re. These model’s ability to predict 'novel' U-Mo alloys is shown quite well despite the discrepancies between literature sources for similar alloys which likely arise from different thermal-mechanical processing conditions. These models are developed with the primary purpose of informing experimental decisions. Additional experimental insight is necessary in order to reduce the number of experiments required to isolate ideal alloys. Thesemore » models allow test planners to evaluate areas of experimental interest; once initial tests are conducted, the model can be updated and further improve follow-on testing decisions. The model also improves analysis capabilities by reducing the number of data points necessary from any particular test. For example, if one or two isotherms are measured during a test, the model can construct the rest of the TTT curve over a wide range of temperature and time. This modeling capability reduces the cost of experiments while also improving the value of the results from the tests. The reduced costs could result in improved material characterization and therefore improved fundamental understanding of TTT dynamics. As additional understanding of phenomena driving TTTs is acquired, this type of MLP model can be used to populate unknowns (such as material impurity and other thermal mechanical properties) from past literature sources.« less

Joint Contracture Orthosis (JCO)

NASA Technical Reports Server (NTRS)

Lunsford, Thomas R.; Parsons, Ken; Krouskop, Thomas; McGee, Kevin

1997-01-01

The purpose of this project was to develop an advanced orthosis which is effective in reducing upper and lower limb contractures in significantly less time than currently required with conventional methods. The team that developed the JCO consisted of an engineer, orthotist, therapist, and physician.

Information Technology Project Processes: Understanding the Barriers to Improvement and Adoption

ERIC Educational Resources Information Center

Williams, Bernard L.

2009-01-01

Every year, organizations lose millions of dollars due to IT (Information Technology) project failures. Over time, organizations have developed processes and procedures to help reduce the incidence of challenged IT projects. Research has shown that IT project processes can work to help reduce the number of challenged projects. The research in this…

Beam-energy-spread minimization using cell-timing optimization

NASA Astrophysics Data System (ADS)

Rose, C. R.; Ekdahl, C.; Schulze, M.

2012-04-01

Beam energy spread, and related beam motion, increase the difficulty in tuning for multipulse radiographic experiments at the dual-axis radiographic hydrodynamic test facility’s axis-II linear induction accelerator (LIA). In this article, we describe an optimization method to reduce the energy spread by adjusting the timing of the cell voltages (both unloaded and loaded), either advancing or retarding, such that the injector voltage and summed cell voltages in the LIA result in a flatter energy profile. We developed a nonlinear optimization routine which accepts as inputs the 74 cell-voltage, injector voltage, and beam current waveforms. It optimizes cell timing per user-selected groups of cells and outputs timing adjustments, one for each of the selected groups. To verify the theory, we acquired and present data for both unloaded and loaded cell-timing optimizations. For the unloaded cells, the preoptimization baseline energy spread was reduced by 34% and 31% for two shots as compared to baseline. For the loaded-cell case, the measured energy spread was reduced by 49% compared to baseline.

Continuous piecewise-linear, reduced-order electrochemical model for lithium-ion batteries in real-time applications

NASA Astrophysics Data System (ADS)

Farag, Mohammed; Fleckenstein, Matthias; Habibi, Saeid

2017-02-01

Model-order reduction and minimization of the CPU run-time while maintaining the model accuracy are critical requirements for real-time implementation of lithium-ion electrochemical battery models. In this paper, an isothermal, continuous, piecewise-linear, electrode-average model is developed by using an optimal knot placement technique. The proposed model reduces the univariate nonlinear function of the electrode's open circuit potential dependence on the state of charge to continuous piecewise regions. The parameterization experiments were chosen to provide a trade-off between extensive experimental characterization techniques and purely identifying all parameters using optimization techniques. The model is then parameterized in each continuous, piecewise-linear, region. Applying the proposed technique cuts down the CPU run-time by around 20%, compared to the reduced-order, electrode-average model. Finally, the model validation against real-time driving profiles (FTP-72, WLTP) demonstrates the ability of the model to predict the cell voltage accurately with less than 2% error.

Bone morphogenetic protein 2 (BMP2) and krüppel-like factor 9 (KLF9) cross-regulation in uterine stromal cells promotes timing of uterine endometrial receptivity

USDA-ARS?s Scientific Manuscript database

An out-of-phase uterus is considered to be a major cause of infertility in mammals. Delayed on-time implantation of developing blastocysts, due to asynchronous endometrial development, results in reduced litter size in mice. The dysregulation of events in the transition from a pre-receptive to a re...

A Time-Out Checklist for Pediatric Regional Anesthetics

NASA Technical Reports Server (NTRS)

Clebone, Anna; Burian, Barbara K.; Polaner, David M.

2017-01-01

Although pediatric regional anesthesia has a demonstrated record of safety, adverse events, especially those related to block performance issues, still may occur. To reduce the frequency of those events, we developed a Regional Anesthesia Time-Out Checklist using expert opinion and the Delphi method.

Monitoring Statistics Which Have Increased Power over a Reduced Time Range.

ERIC Educational Resources Information Center

Tang, S. M.; MacNeill, I. B.

1992-01-01

The problem of monitoring trends for changes at unknown times is considered. Statistics that permit one to focus high power on a segment of the monitored period are studied. Numerical procedures are developed to compute the null distribution of these statistics. (Author)

Ares I Upper Stage Update

NASA Technical Reports Server (NTRS)

Davis, Daniel J.

2010-01-01

These presentation slides review the progress in the development of the Ares I upper stage. The development includes development of a manufacturing and processing assembly that will reduce the time required over 100 days, development of a weld tool that is a robotic tool that is the largest welder of its kind in the United States, development of avionics and software, and development of logisitics and operations systems.

Collaborative Interventions Reduce Time-to-Thrombolysis for Acute Ischemic Stroke in a Public Safety Net Hospital.

PubMed

Threlkeld, Zachary D; Kozak, Benjamin; McCoy, David; Cole, Sara; Martin, Christine; Singh, Vineeta

2017-07-01

Shorter time-to-thrombolysis in acute ischemic stroke (AIS) is associated with improved functional outcome and reduced morbidity. We evaluate the effect of several interventions to reduce time-to-thrombolysis at an urban, public safety net hospital. All patients treated with tissue plasminogen activator for AIS at our institution between 2008 and 2015 were included in a retrospective analysis of door-to-needle (DTN) time and associated factors. Between 2011 and 2014, we implemented 11 distinct interventions to reduce DTN time. Here, we assess the relative impact of each intervention on DTN time. The median DTN time pre- and postintervention decreased from 87 (interquartile range: 68-109) minutes to 49 (interquartile range: 39-63) minutes. The reduction was comprised primarily of a decrease in median time from computed tomography scan order to interpretation. The goal DTN time of 60 minutes or less was achieved in 9% (95% confidence interval: 5%-22%) of cases preintervention, compared with 70% (58%-81%) postintervention. Interventions with the greatest impact on DTN time included the implementation of a stroke group paging system, dedicated emergency department stroke pharmacists, and the development of a stroke code supply box. Multidisciplinary, collaborative interventions are associated with a significant and substantial reduction in time-to-thrombolysis. Such targeted interventions are efficient and achievable in resource-limited settings, where they are most needed. Copyright © 2017 National Stroke Association. Published by Elsevier Inc. All rights reserved.

New techniques in television to provide research in three-dimensional real-time or near real-time imagery and reduced cost systems for teleconferencing and educational uses, part 1

NASA Technical Reports Server (NTRS)

Pao, Y. H.; Claspy, P.; Allen, J. E.; Merat, F.

1979-01-01

The results are presented of a continuing research and development program the objective of which is to develop a reduced bandwidth television system and a technique for television transmission of holograms. The result of the former is a variable frame rate television system, the operation of which was demonstrated for both black-and-white and color signals. This system employs a novel combination of the inexpensive mass storage capacity of a magnetic disc with the reliability of a digital system for time expansion and compression. Also reported are the results of a theoretical analysis and preliminary feasibility experiment of an innovative system for television transmission of holograms using relatively conventional TV equipment along with a phase modulated reference wave for production of the original interference pattern.

How can Human Intelligence Enhance Collection in an Era of Un-manned Technology and Reduced Personnel?

DTIC Science & Technology

2014-12-12

nexus of intelligence and technology is like a new toy for a small child . The President, the CIA, and the entire intelligence community have become...that could. The espionage trade was developed by using the technology available at the time, and incorporating any means available to collect relevant...reduced immediate need, such as an ongoing or developing conflict or war, is it responsible to maintain a capability just in case, where there may be an

Behavioral Health and Performance (BHP) Work-Rest Cycles

NASA Technical Reports Server (NTRS)

Leveton, Lauren B.; Whitmire, Alexandra

2011-01-01

BHP Program Element Goal: Identify, characterize, and prevent or reduce behavioral health and performance risks associated with space travel, exploration and return to terrestrial life. BHP Requirements: a) Characterize and assess risks (e.g., likelihood and consequences). b) Develop tools and technologies to prevent, monitor, and treat adverse outcomes. c) Inform standards. d) Develop technologies to: 1) reduce risks and human systems resource requirements (e.g., crew time, mass, volume, power) and 2) ensure effective human-system integration across exploration mission.

76 FR 6143 - Draft Guidance for Industry on “Target Animal Safety and Effectiveness Protocol Development and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-03

...] Draft Guidance for Industry on ``Target Animal Safety and Effectiveness Protocol Development and...) entitled ``Target Animal Safety and Effectiveness Protocol Development and Submission.'' The purpose of... Center for Veterinary Medicine (CVM), Office of New Animal Drug Evaluation (ONADE), to reduce the time to...

The Florida Educational Research and Development Program. Second Annual Report.

ERIC Educational Resources Information Center

Florida State Dept. of Education, Tallahassee.

This report describes the efforts being made through the Educational Research and Development Program to implement the new state strategy of reducing restrictions on local and institutional officials and at the same time holding them accountable for the effectiveness of their programs. Chapter II considers the development of techniques for…

A Framework for Safe Composition of Heterogeneous SOA Services in a Pervasive Computing Environment with Resource Constraints

ERIC Educational Resources Information Center

Reyes Alamo, Jose M.

2010-01-01

The Service Oriented Computing (SOC) paradigm, defines services as software artifacts whose implementations are separated from their specifications. Application developers rely on services to simplify the design, reduce the development time and cost. Within the SOC paradigm, different Service Oriented Architectures (SOAs) have been developed.…

Multilevel wireless capsule endoscopy video segmentation

NASA Astrophysics Data System (ADS)

Hwang, Sae; Celebi, M. Emre

2010-03-01

Wireless Capsule Endoscopy (WCE) is a relatively new technology (FDA approved in 2002) allowing doctors to view most of the small intestine. WCE transmits more than 50,000 video frames per examination and the visual inspection of the resulting video is a highly time-consuming task even for the experienced gastroenterologist. Typically, a medical clinician spends one or two hours to analyze a WCE video. To reduce the assessment time, it is critical to develop a technique to automatically discriminate digestive organs and shots each of which consists of the same or similar shots. In this paper a multi-level WCE video segmentation methodology is presented to reduce the examination time.

Observed use of voluntary controls to reduce physical exposures among sheet metal workers of the mechanical trade

PubMed Central

Dale, Ann Marie; Miller, Kim; Gardner, Bethany T.; Hwang, Ching-Ting; Evanoff, Bradley; Welch, Laura

2015-01-01

Introduction Little is known about the transfer into the workplace of interventions designed to reduce the physical demands of sheet metal workers. Methods We reviewed videos from a case series of 15 sheet metal worksite assessments performed in 2007–2009 to score postures and physical loads, and to observe the use of recommended interventions to reduce physical exposures in sheet metal activities made by a NIOSH stakeholder meeting in 2002. Results Workers showed consistent use of material handling devices, but we observed few uses of recommended interventions to reduce exposures during overhead work. Workers spent large proportions of time in awkward shoulder elevation and low back rotation postures. Conclusions In addition to the development of new technologies and system designs, increased adoption of existing tools and practices could reduce time spent in awkward postures and other risks for musculoskeletal disorders in sheet metal work. PMID:26360196

Reduced corticomotor excitability and motor skills development in children born preterm

PubMed Central

Pitcher, Julia B; Schneider, Luke A; Burns, Nicholas R; Drysdale, John L; Higgins, Ryan D; Ridding, Michael C; Nettelbeck, Theodore J; Haslam, Ross R; Robinson, Jeffrey S

2012-01-01

The mechanisms underlying the altered neurodevelopment commonly experienced by children born preterm, but without brain lesions, remain unknown. While individuals born the earliest are at most risk, late preterm children also experience significant motor, cognitive and behavioural dysfunction from school age, and reduced income and educational attainment in adulthood. We used transcranial magnetic stimulation and functional assessments to examine corticomotor development in 151 children without cerebral palsy, aged 10–13 years and born after gestations of 25–41 completed weeks. We hypothesized that motor cortex and corticospinal development are altered in preterm children, which underpins at least some of their motor dysfunction. We report for the first time that every week of reduced gestation is associated with a reduction in corticomotor excitability that remains evident in late childhood. This reduced excitability was associated with poorer motor skill development, particularly manual dexterity. However, child adiposity, sex and socio-economic factors regarding the child's home environment soon after birth were also powerful influences on development of motor skills. Preterm birth was also associated with reduced left hemisphere lateralization, but without increasing the likelihood of being left handed per se. These corticomotor findings have implications for normal motor development, but also raise questions regarding possible longer term consequences of preterm birth on motor function. PMID:22966161

Software Aids Visualization of Computed Unsteady Flow

NASA Technical Reports Server (NTRS)

Kao, David; Kenwright, David

2003-01-01

Unsteady Flow Analysis Toolkit (UFAT) is a computer program that synthesizes motions of time-dependent flows represented by very large sets of data generated in computational fluid dynamics simulations. Prior to the development of UFAT, it was necessary to rely on static, single-snapshot depictions of time-dependent flows generated by flow-visualization software designed for steady flows. Whereas it typically takes weeks to analyze the results of a largescale unsteady-flow simulation by use of steady-flow visualization software, the analysis time is reduced to hours when UFAT is used. UFAT can be used to generate graphical objects of flow visualization results using multi-block curvilinear grids in the format of a previously developed NASA data-visualization program, PLOT3D. These graphical objects can be rendered using FAST, another popular flow visualization software developed at NASA. Flow-visualization techniques that can be exploited by use of UFAT include time-dependent tracking of particles, detection of vortex cores, extractions of stream ribbons and surfaces, and tetrahedral decomposition for optimal particle tracking. Unique computational features of UFAT include capabilities for automatic (batch) processing, restart, memory mapping, and parallel processing. These capabilities significantly reduce analysis time and storage requirements, relative to those of prior flow-visualization software. UFAT can be executed on a variety of supercomputers.

Gaps in the Body of Knowledge of Systems Engineering

DTIC Science & Technology

2012-07-01

practices, agile development, Kanban , risk management, and decision management. This focus is being driven by the need to reduce time for delivery of...to incorporate Kanban approaches to scheduling the SE activities based on value. Rapid Fielding. In this situation, there is a short time to

STAT6 inhibitory peptide given during RSV infection of neonatal mice reduces exacerbated airway responses upon adult reinfection.

PubMed

Srinivasa, Bharat T; Restori, Katherine H; Shan, Jichuan; Cyr, Louis; Xing, Li; Lee, Soojin; Ward, Brian J; Fixman, Elizabeth D

2017-02-01

Respiratory syncytial virus (RSV)-related hospitalization during infancy is strongly associated with the subsequent development of asthma. Early life RSV infection results in a Th2-biased immune response, which is also typical of asthma. Murine models of neonatal RSV infection have been developed to examine the possible contribution of RSV-driven Th2 responses to the development of airway hyper-responsiveness later in childhood. We have investigated the ability of a cell-penetrating STAT6 inhibitory peptide (STAT6-IP), when delivered selectively during neonatal RSV infection, to modify pathogenesis induced upon secondary RSV reinfection of adults 6 wk later. Neonatal STAT6-IP treatment inhibited the development of airway hyper-responsiveness (AHR) and significantly reduced lung eosinophilia and collagen deposition in adult mice following RSV reinfection. STAT6-IP-treated, RSV-infected neonates had reduced levels of both IL-4 and alternatively activated macrophages (AAMs) in the lungs. Our findings suggest that targeting STAT6 activity at the time of early-life RSV infection may effectively reduce the risk of subsequent asthma development. © Society for Leukocyte Biology.

Advanced flow noise reducing acoustic sensor arrays

NASA Astrophysics Data System (ADS)

Fine, Kevin; Drzymkowski, Mark; Cleckler, Jay

2009-05-01

SARA, Inc. has developed microphone arrays that are as effective at reducing flow noise as foam windscreens and sufficiently rugged for tough battlefield environments. These flow noise reducing (FNR) sensors have a metal body and are flat and conformally mounted so they can be attached to the roofs of land vehicles and are resistant to scrapes from branches. Flow noise at low Mach numbers is created by turbulent eddies moving with the fluid flow and inducing pressure variations on microphones. Our FNR sensors average the pressure over the diameter (~20 cm) of their apertures, reducing the noise created by all but the very largest eddies. This is in contrast to the acoustic wave which has negligible variation over the aperture at the frequencies of interest (f less or equal than 400 Hz). We have also post-processed the signals to further reduce the flow noise. Two microphones separated along the flow direction exhibit highly correlated noise. The time shift of the correlation corresponds to the time for the eddies in the flow to travel between the microphones. We have created linear microphone arrays parallel to the flow and have reduced flow noise as much as 10 to 15 dB by subtracting time-shifted signals.

Adaptive model-predictive controller for magnetic resonance guided focused ultrasound therapy.

PubMed

de Bever, Joshua; Todd, Nick; Payne, Allison; Christensen, Douglas A; Roemer, Robert B

2014-11-01

Minimising treatment time and protecting healthy tissues are conflicting goals that play major roles in making magnetic resonance image-guided focused ultrasound (MRgFUS) therapies clinically practical. We have developed and tested in vivo an adaptive model-predictive controller (AMPC) that reduces treatment time, ensures safety and efficacy, and provides flexibility in treatment set-up. The controller realises time savings by modelling the heated treatment cell's future temperatures and thermal dose accumulation in order to anticipate the optimal time to switch to the next cell. Selected tissues are safeguarded by a configurable temperature constraint. Simulations quantified the time savings realised by each controller feature as well as the trade-offs between competing safety and treatment time parameters. In vivo experiments in rabbit thighs established the controller's effectiveness and reliability. In all in vivo experiments the target thermal dose of at least 240 CEM43 was delivered everywhere in the treatment volume. The controller's temperature safety limit reliably activated and constrained all protected tissues to <9 CEM43. Simulations demonstrated the path independence of the controller, and that a path which successively proceeds to the hottest untreated neighbouring cell leads to significant time savings, e.g. when compared to a concentric spiral path. Use of the AMPC produced a compounding time-saving effect; reducing the treatment cells' heating times concurrently reduced heating of normal tissues, which eliminated cooling periods. Adaptive model-predictive control can automatically deliver safe, effective MRgFUS treatments while significantly reducing treatment times.

Development of CVD Diamond for Industrial Applications Final Report CRADA No. TC-2047-02

DOE Office of Scientific and Technical Information (OSTI.GOV)

Caplan, M.; Olstad, R.; Jory, H.

2017-09-08

This project was a collaborative effort to develop and demonstrate a new millimeter microwave assisted chemical vapor deposition(CVD) process for manufacturing large diamond disks with greatly reduced processing times and costs from those now available. In the CVD process, carbon based gases (methane) and hydrogen are dissociated into plasma using microwave discharge and then deposited layer by layer as polycrystalline diamond onto a substrate. The available low frequency (2.45GHz) microwave sources used elsewhere (De Beers) result in low density plasmas and low deposition rates: 4 inch diamond disks take 6-8 weeks to process. The new system developed in this projectmore » uses a high frequency 30GHz Gyrotron as the microwave source and a quasi-optical CVD chamber resulting in a much higher density plasma which greatly reduced the diamond processing times (1-2 weeks)« less

Development and preliminary evaluation of an Android based heart rate variability biofeedback system.

PubMed

Abtahi, F; Berndtsson, A; Abtahi, S; Seoane, F; Lindecrantz, K

2014-01-01

The reduced Heart Rate Variability (HRV) is believed to be associated with several diseases such as congestive heart failure, diabetes and chronic kidney diseases (CKD). In these cases, HRV biofeedback may be a potential intervention method to increase HRV which in turn is beneficial to these patients. In this work, a real-time Android biofeedback application based on a Bluetooth enabled ECG and thoracic electrical bioimpedance (respiration) measurement device has been developed. The system performance and usability have been evaluated in a brief study with eight healthy volunteers. The result demonstrates real-time performance of system and positive effects of biofeedback training session by increased HRV and reduced heart rate. Further development of the application and training protocol is ongoing to investigate duration of training session to find an optimum length and interval of biofeedback sessions to use in potential interventions.

Practical solutions for reducing container ships' waiting times at ports using simulation model

NASA Astrophysics Data System (ADS)

Sheikholeslami, Abdorreza; Ilati, Gholamreza; Yeganeh, Yones Eftekhari

2013-12-01

The main challenge for container ports is the planning required for berthing container ships while docked in port. Growth of containerization is creating problems for ports and container terminals as they reach their capacity limits of various resources which increasingly leads to traffic and port congestion. Good planning and management of container terminal operations reduces waiting time for liner ships. Reducing the waiting time improves the terminal's productivity and decreases the port difficulties. Two important keys to reducing waiting time with berth allocation are determining suitable access channel depths and increasing the number of berths which in this paper are studied and analyzed as practical solutions. Simulation based analysis is the only way to understand how various resources interact with each other and how they are affected in the berthing time of ships. We used the Enterprise Dynamics software to produce simulation models due to the complexity and nature of the problems. We further present case study for berth allocation simulation of the biggest container terminal in Iran and the optimum access channel depth and the number of berths are obtained from simulation results. The results show a significant reduction in the waiting time for container ships and can be useful for major functions in operations and development of container ship terminals.

Development of an Agent Based Model to Estimate and Reduce Time to Restoration of Storm Induced Power Outages

NASA Astrophysics Data System (ADS)

Walsh, T.; Layton, T.; Mellor, J. E.

2017-12-01

Storm damage to the electric grid impacts 23 million electric utility customers and costs US consumers $119 billion annually. Current restoration techniques rely on the past experiences of emergency managers. There are few analytical simulation and prediction tools available for utility managers to optimize storm recovery and decrease consumer cost, lost revenue and restoration time. We developed an agent based model (ABM) for storm recovery in Connecticut. An ABM is a computer modeling technique comprised of agents who are given certain behavioral rules and operate in a given environment. It allows the user to simulate complex systems by varying user-defined parameters to study emergent, unpredicted behavior. The ABM incorporates the road network and electric utility grid for the state, is validated using actual storm event recoveries and utilizes the Dijkstra routing algorithm to determine the best path for repair crews to travel between outages. The ABM has benefits for both researchers and utility managers. It can simulate complex system dynamics, rank variable importance, find tipping points that could significantly reduce restoration time or costs and test a broad range of scenarios. It is a modular, scalable and adaptable technique that can simulate scenarios in silico to inform emergency managers before and during storm events to optimize restoration strategies and better manage expectations of when power will be restored. Results indicate that total restoration time is strongly dependent on the number of crews. However, there is a threshold whereby more crews will not decrease the restoration time, which depends on the total number of outages. The addition of outside crews is more beneficial for storms with a higher number of outages. The time to restoration increases linearly with increasing repair time, while the travel speed has little overall effect on total restoration time. Crews traveling to the nearest outage reduces the total restoration time, while crews going to the outage with most customers affected increases the overall restoration time but more quickly decreases the customers remaining without power. This model can give utility company managers the ability to optimize their restoration strategies before or during a storm event to reduce restoration times and costs.

Spring thaw predictor & development of real time spring load restrictions.

DOT National Transportation Integrated Search

2011-02-01

This report summarizes the results of a study to develop a correlation between weather forecasts and the : spring thaw in order to reduce the duration of load limits on New Hampshire roadways. The study used a falling : weight deflectometer at 10 sit...

Trends in the Development of Alternative Work Patterns.

ERIC Educational Resources Information Center

McCarthy, Maureen

1979-01-01

Flexible scheduling and reduced work time programs can help alleviate some of the pressures on public and private employers to develop innovative solutions to problems caused by inflation, unemployment, the transition in the composition of the workforce, and changes in life-styles. (Author/IRT)

Scaling Watershed Models: Modern Approaches to Science Computation with MapReduce, Parallelization, and Cloud Optimization

EPA Science Inventory

Environmental models are products of the computer architecture and software tools available at the time of development. Scientifically sound algorithms may persist in their original state even as system architectures and software development approaches evolve and progress. Dating...

Effects of generation time on spray aerosol transport and deposition in models of the mouth-throat geometry.

PubMed

Worth Longest, P; Hindle, Michael; Das Choudhuri, Suparna

2009-06-01

For most newly developed spray aerosol inhalers, the generation time is a potentially important variable that can be fully controlled. The objective of this study was to determine the effects of spray aerosol generation time on transport and deposition in a standard induction port (IP) and more realistic mouth-throat (MT) geometry. Capillary aerosol generation (CAG) was selected as a representative system in which spray momentum was expected to significantly impact deposition. Sectional and total depositions in the IP and MT geometries were assessed at a constant CAG flow rate of 25 mg/sec for aerosol generation times of 1, 2, and 4 sec using both in vitro experiments and a previously developed computational fluid dynamics (CFD) model. Both the in vitro and numerical results indicated that extending the generation time of the spray aerosol, delivered at a constant mass flow rate, significantly reduced deposition in the IP and more realistic MT geometry. Specifically, increasing the generation time of the CAG system from 1 to 4 sec reduced the deposition fraction in the IP and MT geometries by approximately 60 and 33%, respectively. Furthermore, the CFD predictions of deposition fraction were found to be in good agreement with the in vitro results for all times considered in both the IP and MT geometries. The numerical results indicated that the reduction in deposition fraction over time was associated with temporal dissipation of what was termed the spray aerosol "burst effect." Based on these results, increasing the spray aerosol generation time, at a constant mass flow rate, may be an effective strategy for reducing deposition in the standard IP and in more realistic MT geometries.

Future directions for the development of virtual reality within an automotive manufacturer.

PubMed

Lawson, Glyn; Salanitri, Davide; Waterfield, Brian

2016-03-01

Virtual Reality (VR) can reduce time and costs, and lead to increases in quality, in the development of a product. Given the pressure on car companies to reduce time-to-market and to continually improve quality, the automotive industry has championed the use of VR across a number of applications, including design, manufacturing, and training. This paper describes interviews with 11 engineers and employees of allied disciplines from an automotive manufacturer about their current physical and virtual properties and processes. The results guided a review of research findings and scientific advances from the academic literature, which formed the basis of recommendations for future developments of VR technologies and applications. These include: develop a greater range of virtual contexts; use multi-sensory simulation; address perceived differences between virtual and real cars; improve motion capture capabilities; implement networked 3D technology; and use VR for market research. Copyright © 2015 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Reducing Behavior Problems Among Students with Autism Spectrum Disorder: Coaching Teachers in a Mixed-Reality Setting.

PubMed

Pas, Elise T; Johnson, Stacy R; Larson, Kristine E; Brandenburg, Linda; Church, Robin; Bradshaw, Catherine P

2016-12-01

Most approaches aiming to reduce behavior problems among youth with Autism Spectrum Disorder (ASD) focus on individual students; however, school personnel also need professional development to better support students. This study targeted teachers' skill development to promote positive outcomes for students with ASD. The sample included 19 teachers in two non-public special education settings serving students with moderate to severe ASD. Participating teachers received professional development and coaching in classroom management, with guided practice in a mixed-reality simulator. Repeated-measures ANOVAs examining externally-conducted classroom observations revealed statistically significant improvements in teacher management and student behavior over time. Findings suggest that coaching and guided practice in a mixed-reality simulator is perceived as acceptable and may reduce behavior problems among students with ASD.

[Development of wireless monitoring system based on Zigbee technology in blood and bacterin cold chain].

PubMed

Zhao, Peng; Sun, Jian-Jun; Wu, Tai-Hu

2008-11-01

Real-time monitoring for temperature is required in cold chain for the medical products that are sensible with temperature, such as blood and bacterin, to guarantee the quality and reduce their wastage. This wireless monitoring system in cold chain is developed with Zigbee technology. Functions such as real-time monitoring, analyzing, alarming are realized. The system boasts such characteristics as low power consumption, low cost, big capacity and high reliability, and could improve the capability of real-time monitoring and management in cold chain effectively.

An Implicit Theories of Personality Intervention Reduces Adolescent Aggression in Response to Victimization and Exclusion

ERIC Educational Resources Information Center

Yeager, David Scott; Trzesniewski, Kali H.; Dweck, Carol S.

2013-01-01

Adolescents are often resistant to interventions that reduce aggression in children. At the same time, they are developing stronger beliefs in the fixed nature of personal characteristics, particularly aggression. The present intervention addressed these beliefs. A randomized field experiment with a diverse sample of Grades 9 and 10 students (ages…

Low Cost Manufacturing Approach of High Temperature PMC Components

NASA Technical Reports Server (NTRS)

Kannmacher, Kevin

1997-01-01

The overall objective is to develop a satisfactory sheet molding compound (SMC) of a high temperature polyimide, such as PMR-11-50, VCAP-75, or NB2-76, and to develop compression molding processing parameters for a random, chopped fiber, high temperature, sheet molding compound that will be more affordable than the traditional hand lay-up fabrication methods. Compression molding will reduce manufacturing costs of composites by: (1) minimizing the conventional machining required after fabrication due to the use of full 360 deg matched tooling, (2) reducing fabrication time by minimizing the intensive hand lay-up operations associated with individual ply fabrication techniques, such as ply orientation and ply count and (3) possibly reducing component mold time by advanced B-staging prior to molding. This program is an integral part of Allison's T406/AE engine family's growth plan, which will utilize technologies developed under NASA's Sub-sonic Transport (AST) programs, UHPTET initiatives, and internally through Allison's IR&D projects. Allison is aggressively pursuing this next generation of engines, with both commercial and military applications, by reducing the overall weight of the engine through the incorporation of advanced, lightweight, high temperature materials, such as polymer matrix composites. This infusion of new materials into the engine is also a major factor in reducing engine cost because it permits the use of physically smaller structural components to achieve the same thrust levels as the generation that it replaced. A lighter, more efficient propulsion system translates to a substantial cost and weight savings to an airframe's structure.

nu-Anomica: A Fast Support Vector Based Novelty Detection Technique

NASA Technical Reports Server (NTRS)

Das, Santanu; Bhaduri, Kanishka; Oza, Nikunj C.; Srivastava, Ashok N.

2009-01-01

In this paper we propose nu-Anomica, a novel anomaly detection technique that can be trained on huge data sets with much reduced running time compared to the benchmark one-class Support Vector Machines algorithm. In -Anomica, the idea is to train the machine such that it can provide a close approximation to the exact decision plane using fewer training points and without losing much of the generalization performance of the classical approach. We have tested the proposed algorithm on a variety of continuous data sets under different conditions. We show that under all test conditions the developed procedure closely preserves the accuracy of standard one-class Support Vector Machines while reducing both the training time and the test time by 5 - 20 times.

A Reduced Set of Features for Chronic Kidney Disease Prediction

PubMed Central

Misir, Rajesh; Mitra, Malay; Samanta, Ranjit Kumar

2017-01-01

Chronic kidney disease (CKD) is one of the life-threatening diseases. Early detection and proper management are solicited for augmenting survivability. As per the UCI data set, there are 24 attributes for predicting CKD or non-CKD. At least there are 16 attributes need pathological investigations involving more resources, money, time, and uncertainties. The objective of this work is to explore whether we can predict CKD or non-CKD with reasonable accuracy using less number of features. An intelligent system development approach has been used in this study. We attempted one important feature selection technique to discover reduced features that explain the data set much better. Two intelligent binary classification techniques have been adopted for the validity of the reduced feature set. Performances were evaluated in terms of four important classification evaluation parameters. As suggested from our results, we may more concentrate on those reduced features for identifying CKD and thereby reduces uncertainty, saves time, and reduces costs. PMID:28706750

An examination of shoulder kinematics and kinetics when using a commercial trunk harness while sheep shearing.

PubMed

Gregory, Diane E; Milosavljevic, Stephan; Pal, Poonam; Callaghan, Jack P

2008-01-01

Sheep shearing is a very physically demanding occupation, especially on the low back, such that many commercial harnesses have been developed to help reduce the load on the back. Such harnesses have been shown to significantly reduce peak and cumulative low back loads; however, the effect that these harnesses have on the shoulders, which are also highly involved during sheep shearing, has not been previously examined. The purpose of this study was to examine the shoulder postures and cumulative shoulder moments of 12 New Zealand sheep shearers. The use of the trunk harness reduced the percentage of time spent in shoulder flexion greater than 90 degrees and the time spent in shoulder abduction greater than 45 degrees as well as reduced the cumulative net joint flexor, abductor, and adductor shoulder moments by a minimum of 21%, 14%, and 42%, respectively. Therefore, the use of a commercial trunk harness to reduce low back injury may also help to reduce the risk of shoulder injury while sheep shearing.

Fast Response Shape Memory Effect Titanium Nickel (TiNi) Foam Torque Tubes

NASA Technical Reports Server (NTRS)

Jardine, Peter

2014-01-01

Shape Change Technologies has developed a process to manufacture net-shaped TiNi foam torque tubes that demonstrate the shape memory effect. The torque tubes dramatically reduce response time by a factor of 10. This Phase II project matured the actuator technology by rigorously characterizing the process to optimize the quality of the TiNi and developing a set of metrics to provide ISO 9002 quality assurance. A laboratory virtual instrument engineering workbench (LabVIEW'TM')-based, real-time control of the torsional actuators was developed. These actuators were developed with The Boeing Company for aerospace applications.

76 FR 770 - Proposed Information Collection; Comment Request; Monthly Wholesale Trade Survey

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-06

... reduces the time and cost of preparing mailout packages that contain unique variable data, while improving... developing productivity measurements. Estimates produced from the MWTS are based on a probability sample and..., excluding manufacturers' sales branches and offices. Estimated Number of Respondents: 4,500. Estimated Time...

Speeding Products to Market: Waiting Time to First Product Introduction in New Firms.

ERIC Educational Resources Information Center

Schoonhoven, Claudia Bird; And Others

1990-01-01

Using event-history analysis techniques, a longitudinal study of the semiconductor industry found that substantial technological innovation lengthens development times and reduces the speed with which first products reach the marketplace. Organizations that undertook lower levels of technological innovation had relatively lower monthly…

Supply chain quality.

PubMed

Feary, Simon

2009-01-01

As the development of complex manufacturing models and virtual companies become more prevalent in today's growing global markets, it is increasingly important to support the relationships between manufacturer and supplier. Utilising these relationships will ensure that supply chains operate more effectively and reduce costs, risks and time-to-market time frames, whilst maintaining product quality.

Helping Parents Reduce Children's Television Viewing

ERIC Educational Resources Information Center

Jason, Leonard A.; Fries, Michael

2004-01-01

Parents and educators around the country are concerned about the amount of time children watch television. Part of this concern stems from the fact that a considerable amount of violence is regularly portrayed on television. In addition, those youngsters who watch an excessive amount of television have little time for developing other interests…

Additive Manufacturing Infrared Inspection

NASA Technical Reports Server (NTRS)

Gaddy, Darrell; Nettles, Mindy

2015-01-01

The Additive Manufacturing Infrared Inspection Task started the development of a real-time dimensional inspection technique and digital quality record for the additive manufacturing process using infrared camera imaging and processing techniques. This project will benefit additive manufacturing by providing real-time inspection of internal geometry that is not currently possible and reduce the time and cost of additive manufactured parts with automated real-time dimensional inspections which deletes post-production inspections.

New Trends in Two-Way Time and Frequency Transfer via Satellite

DTIC Science & Technology

1999-12-01

Recent developments performed with SATRE two-way time transfer ( TWSTFT ) modems resulted in significant performance upgrades and operational...improvements of the TWSTFT method These are aimed to reduce : manpower effort and to provide reliable, real-time data via a centralized monitoring and...collection have been used throughout the experiment INTRODUCTION Two-Way Time and Frequency Transfer via Satellite ( TWSTFT ) is a well established method to

A Development Architecture for Serious Games Using BCI (Brain Computer Interface) Sensors

PubMed Central

Sung, Yunsick; Cho, Kyungeun; Um, Kyhyun

2012-01-01

Games that use brainwaves via brain–computer interface (BCI) devices, to improve brain functions are known as BCI serious games. Due to the difficulty of developing BCI serious games, various BCI engines and authoring tools are required, and these reduce the development time and cost. However, it is desirable to reduce the amount of technical knowledge of brain functions and BCI devices needed by game developers. Moreover, a systematic BCI serious game development process is required. In this paper, we present a methodology for the development of BCI serious games. We describe an architecture, authoring tools, and development process of the proposed methodology, and apply it to a game development approach for patients with mild cognitive impairment as an example. This application demonstrates that BCI serious games can be developed on the basis of expert-verified theories. PMID:23202227

A development architecture for serious games using BCI (brain computer interface) sensors.

PubMed

Sung, Yunsick; Cho, Kyungeun; Um, Kyhyun

2012-11-12

Games that use brainwaves via brain-computer interface (BCI) devices, to improve brain functions are known as BCI serious games. Due to the difficulty of developing BCI serious games, various BCI engines and authoring tools are required, and these reduce the development time and cost. However, it is desirable to reduce the amount of technical knowledge of brain functions and BCI devices needed by game developers. Moreover, a systematic BCI serious game development process is required. In this paper, we present a methodology for the development of BCI serious games. We describe an architecture, authoring tools, and development process of the proposed methodology, and apply it to a game development approach for patients with mild cognitive impairment as an example. This application demonstrates that BCI serious games can be developed on the basis of expert-verified theories.

A new approach to road accident rescue.

PubMed

Morales, Alejandro; González-Aguilera, Diego; López, Alfonso I; Gutiérrez, Miguel A

2016-01-01

This article develops and validates a new methodology and tool for rescue assistance in traffic accidents, with the aim of improving its efficiency and safety in the evacuation of people, reducing the number of victims in road accidents. Different tests supported by professionals and experts have been designed under different circumstances and with different categories of damaged vehicles coming from real accidents and simulated trapped victims in order to calibrate and refine the proposed methodology and tool. To validate this new approach, a tool called App_Rescue has been developed. This tool is based on the use of a computer system that allows an efficient access to the technical information of the vehicle and sanitary information of the common passengers. The time spent during rescue using the standard protocol and the proposed method was compared. This rescue assistance system allows us to make vital information accessible in posttrauma care services, improving the effectiveness of interventions by the emergency services, reducing the rescue time and therefore minimizing the consequences involved and the number of victims. This could often mean saving lives. In the different simulated rescue operations, the rescue time has been reduced an average of 14%.

Evaluation of the impacts of cooperative adaptive cruise control on reducing rear-end collision risks on freeways.

PubMed

Li, Ye; Wang, Hao; Wang, Wei; Xing, Lu; Liu, Shanwen; Wei, Xueyan

2017-01-01

Although plenty of studies have been conducted recently about the impacts of cooperative adaptive cruise control (CACC) system on traffic efficiency, there are few researches analyzing the safety effects of this advanced driving-assistant system. Thus, the primary objective of this study is to evaluate the impacts of the CACC system on reducing rear-end collision risks on freeways. The CACC model is firstly developed, which is based on the Intelligent Driver Model (IDM). Then, two surrogated safety measures, derived from the time-to-collision (TTC), denoting time exposed time-to-collision (TET) and time integrated time-to-collision (TIT), are introduced for quantifying the collision risks. And the safety effects are analyzed both theoretically and experimentally, by the linear stability analysis and simulations. The theoretical and simulation results conformably indicate that the CACC system brings dramatic benefits for reducing rear-end collision risks (TET and TIT are reduced more than 90%, respectively), when the desired time headway and time delay are set properly. The sensitivity analysis indicates there are few differences among different values of the threshold of TTC and the length of a CACC platoon. The results also show that the safety improvements weaken with the decrease of the penetration rates of CACC on the market and the increase of time delay between platoons. We also evaluate the traffic efficiency of the CACC system with different desired time headway. Copyright © 2016 Elsevier Ltd. All rights reserved.

Moderate reagent mixing on an orbital shaker reduces the incubation time of enzyme-linked immunosorbent assay.

PubMed

Kumar, Saroj; Ahirwar, Rajesh; Rehman, Ishita; Nahar, Pradip

2017-07-01

Rapid diagnostic tests can be developed using ELISA for detection of diseases in emergency conditions. Conventional ELISA takes 1-2 days, making it unsuitable for rapid diagnostics. Here, we report the effect of reagents mixing via shaking or vortexing on the assay timing of ELISA. A 48-min protocol of ELISA involving 12-min incubations with reagent mixing at 750 rpm for every step was optimized. Contrary to this, time-optimized control ELISA performed without mixing produced similar results in 8 h, leaving a time gain of 7 h using the developed protocol. Collectively, the findings suggest the development of ELISA-based rapid diagnostics. Copyright © 2017 Elsevier Inc. All rights reserved.

Aircraft Engine Systems

NASA Technical Reports Server (NTRS)

Veres, Joseph P.

2003-01-01

The objective is to develop the capability to numerically model the performance of gas turbine engines used for aircraft propulsion. This capability will provide turbine engine designers with a means of accurately predicting the performance of new engines in a system environment prior to building and testing. The 'numerical test cell' developed under this project will reduce the number of component and engine tests required during development. As a result, the project will help to reduce the design cycle time and cost of gas turbine engines. This capability will be distributed to U.S. turbine engine manufacturers and air framers. This project focuses on goals of maintaining U.S. superiority in commercial gas turbine engine development for the aeronautics industry.

Characterization of cellulose nanofibrillation by micro grinding

Treesearch

Sandeep S. Nair; J.Y. Zhu; Yulin Deng; Arthur J. Ragauskas

2014-01-01

A fundamental understanding of the morphological development of cellulose fibers during fibrillation using micro grinder is very essential to develop effective strategies for process improvement and to reduce energy consumption. We demonstrated some simple measures for characterizing cellulose fibers fibrillated at different fibrillation times through the grinder. The...

Program test objectives milestone 3. [Integrated Propulsion Technology Demonstrator

NASA Technical Reports Server (NTRS)

Gaynor, T. L.

1994-01-01

The following conclusions have been developed relative to propulsion system technology adequacy for efficient development and operation of recoverable and expendable launch vehicles (RLV and ELV) and the benefits which the integrated propulsion technology demonstrator will provide for enhancing technology: (1) Technology improvements relative to propulsion system design and operation can reduce program cost. Many features or improvement needs to enhance operability, reduce cost, and improve payload are identified. (2) The Integrated Propulsion Technology Demonstrator (IPTD) Program provides a means of resolving the majority of issues associated with improvement needs. (3) The IPTD will evaluate complex integration of vehicle and facility functions in fluid management and propulsion control systems, and provides an environment for validating improved mechanical and electrical components. (4) The IPTD provides a mechanism for investigating operational issues focusing on reducing manpower and time to perform various functions at the launch site. These efforts include model development, collection of data to validate subject models, and ultimate development of complex time line models. (5) The IPTD provides an engine test bed for tri/bi-propellant engine development firings which is representative of the actual vehicle environment. (6) The IPTD provides for only a limited multiengine configuration integration environment for RLV. Multiengine efforts may be simulated for a number of subsystems and a number of subsystems are relatively independent of the multiengine influences.

Utilizing lean tools to improve value and reduce outpatient wait times in an Indian hospital.

PubMed

Miller, Richard; Chalapati, Nirisha

2015-01-01

This paper aims to demonstrate how lean tools were applied to some unique issues of providing healthcare in a developing country where many patients face challenges not found in developed countries. The challenges provide insight into how lean tools can be utilized to provide similar results across the world. This paper is based on a qualitative case study carried out by a master's student implementing lean at a hospital in India. This paper finds that lean tools such as value-stream mapping and root cause analysis can lead to dramatic reductions in waste and improvements in productivity. The problems of the majority of patients paying for their own healthcare and lacking transportation created scheduling problems that required patients to receive their diagnosis and pay for treatment within a single day. Many additional wastes were identified that were significantly impacting the hospital's ability to provide care. As a result of this project, average outpatient wait times were reduced from 1 hour to 15 minutes along with a significant increase in labor productivity. The results demonstrate how lean tools can increase value to the patients. It also provides are framework that can be utilized for healthcare providers in developed and developing countries to analyze their value streams to reduce waste. This paper is one of the first to address the unique issues of implementing lean to a healthcare setting in a developing country.

The development of biomarkers to reduce attrition rate in drug discovery focused on oncology and central nervous system.

PubMed

Safavi, Maliheh; Sabourian, Reyhaneh; Abdollahi, Mohammad

2016-10-01

The task of discovery and development of novel therapeutic agents remains an expensive, uncertain, time-consuming, competitive, and inefficient enterprise. Due to a steady increase in the cost and time of drug development and the considerable amount of resources required, a predictive tool is needed for assessing the safety and efficacy of a new chemical entity. This study is focused on the high attrition rate in discovery and development of oncology and central nervous system (CNS) medicines, because the failure rate of these medicines is higher than others. Some approaches valuable in reducing attrition rates are proposed and the judicious use of biomarkers is discussed. Unlike the significant progress made in identifying and characterizing novel mechanisms of disease processes and targeted therapies, the process of novel drug development is associated with an unacceptably high attrition rate. The application of clinically qualified predictive biomarkers holds great promise for further development of therapeutic targets, improved survival, and ultimately personalized medicine sets for patients. Decisions such as candidate selection, development risks, dose ranging, early proof of concept/principle, and patient stratification are based on the measurements of biologically and/or clinically validated biomarkers.

Near-Net Shape Powder Metallurgy Rhenium Thruster

NASA Technical Reports Server (NTRS)

Leonhardt, Todd; Hamister, Mark; Carlen, Jan C.; Biaglow, James; Reed, Brian

2001-01-01

This paper describes the development of a method to produce a near-net shape (NNS) powder metallurgy (PM) rhenium combustion chamber of the size 445 N (100 lbf) used in a high performance liquid apogee engine. These engines are used in low earth Orbit and geostationary orbit for satellite positioning systems. The developments in near-net shape powder metallurgy rhenium combustion chambers reported in this paper will reduce manufacturing cost of the rhenium chambers by 25 percent, and reduce the manufacturing time by 30 to 40 percent. The quantity of rhenium metal powder used to produce a rhenium chamber is reduced by approximately 70 percent and the subsequent reduction in machining schedule and costs is nearly 50 percent.

Out-of-School Time and Adolescent Substance Use.

PubMed

Lee, Kenneth T H; Vandell, Deborah Lowe

2015-11-01

High levels of adolescent substance use are linked to lower academic achievement, reduced schooling, and delinquency. We assess four types of out-of-school time (OST) contexts--unsupervised time with peers, sports, organized activities, and paid employment--in relation to tobacco, alcohol, and marijuana use at the end of high school. Other research has examined these OST contexts in isolation, limiting efforts to disentangle potentially confounded relations. Longitudinal data from the National Institute of Child Health and Human Development Study of Early Child Care and Youth Development (N = 766) examined associations between different OST contexts during high school and substance use at the end of high school. Unsupervised time with peers increased the odds of tobacco, alcohol, and marijuana use, whereas sports increased the odds of alcohol use and decreased the odds of marijuana use. Paid employment increased the odds of tobacco and alcohol use. Unsupervised time with peers predicted increased amounts of tobacco, alcohol, and marijuana use, whereas sports predicted decreased amounts of tobacco and marijuana use and increased amounts of alcohol use at the end of high school. Although unsupervised time with peers, sports, and paid employment were differentially linked to the odds of substance use, only unsupervised time with peers and sports were significantly associated with the amounts of tobacco, alcohol, and marijuana use at the end of high school. These findings underscore the value of considering OST contexts in relation to strategies to promote adolescent health. Reducing unsupervised time with peers and increasing sports participation may have positive impacts on reducing substance use. Copyright © 2015 Society for Adolescent Health and Medicine. Published by Elsevier Inc. All rights reserved.

A Study on the Effectiveness of Lockup-Free Caches for a Reduced Instruction Set Computer (RISC) Processor

DTIC Science & Technology

1992-09-01

to acquire or develop effective simulation tools to observe the behavior of a RISC implementation as it executes different types of programs . We choose...Performance Computer performance is measured by the amount of the time required to execute a program . Performance encompasses two types of time, elapsed time...and CPU time. Elapsed time is the time required to execute a program from start to finish. It includes latency of input/output activities such as

Improving the Fabrication of Semiconductor Bragg Lasers

NASA Astrophysics Data System (ADS)

Chen, Eric Ping Chun

Fabrication process developments for Bragg reflection lasers have been optimized in this thesis using resources available to the group. New e-beam lithography and oxide etch recipes have been developed to minimize sidewall roughness and residues. E-beam evaporated metal contacts for semiconductor diode laser utilizing oblique angle deposition have also been developed in-house for the first time. Furthermore, improvement in micro-loading effect of DFB laser etching has been demonstrated where the ratio of tapered portion of the sidewall to total etch depth is reduced by half, from 33% to 15%. Electrical, optical and thermal performance of the fabricated lasers are characterized. Comparing the results to previous generation lasers, average dynamic resistance is decreased drastically from 14 Ohms to 7 Ohms and threshold current density also reduced from 1705A/cm2 to 1383A/ cm2. Improvement in laser performance is result of reduced loss from optimized fabrication processes. BRL bow-tie tapered lasers is then fabricated for the first time and output power of 18mW at 200mA input is measured. Benefiting from the increased effective area and better carrier utilization, reduction in threshold current density from 1383A/cm 2 to 712A/cm2 is observed.

A soft computing based approach using modified selection strategy for feature reduction of medical systems.

PubMed

Zuhtuogullari, Kursat; Allahverdi, Novruz; Arikan, Nihat

2013-01-01

The systems consisting high input spaces require high processing times and memory usage. Most of the attribute selection algorithms have the problems of input dimensions limits and information storage problems. These problems are eliminated by means of developed feature reduction software using new modified selection mechanism with middle region solution candidates adding. The hybrid system software is constructed for reducing the input attributes of the systems with large number of input variables. The designed software also supports the roulette wheel selection mechanism. Linear order crossover is used as the recombination operator. In the genetic algorithm based soft computing methods, locking to the local solutions is also a problem which is eliminated by using developed software. Faster and effective results are obtained in the test procedures. Twelve input variables of the urological system have been reduced to the reducts (reduced input attributes) with seven, six, and five elements. It can be seen from the obtained results that the developed software with modified selection has the advantages in the fields of memory allocation, execution time, classification accuracy, sensitivity, and specificity values when compared with the other reduction algorithms by using the urological test data.

A Soft Computing Based Approach Using Modified Selection Strategy for Feature Reduction of Medical Systems

PubMed Central

Zuhtuogullari, Kursat; Allahverdi, Novruz; Arikan, Nihat

2013-01-01

The systems consisting high input spaces require high processing times and memory usage. Most of the attribute selection algorithms have the problems of input dimensions limits and information storage problems. These problems are eliminated by means of developed feature reduction software using new modified selection mechanism with middle region solution candidates adding. The hybrid system software is constructed for reducing the input attributes of the systems with large number of input variables. The designed software also supports the roulette wheel selection mechanism. Linear order crossover is used as the recombination operator. In the genetic algorithm based soft computing methods, locking to the local solutions is also a problem which is eliminated by using developed software. Faster and effective results are obtained in the test procedures. Twelve input variables of the urological system have been reduced to the reducts (reduced input attributes) with seven, six, and five elements. It can be seen from the obtained results that the developed software with modified selection has the advantages in the fields of memory allocation, execution time, classification accuracy, sensitivity, and specificity values when compared with the other reduction algorithms by using the urological test data. PMID:23573172

Development of Automated Image Analysis Software for Suspended Marine Particle Classification

DTIC Science & Technology

2003-09-30

Development of Automated Image Analysis Software for Suspended Marine Particle Classification Scott Samson Center for Ocean Technology...REPORT TYPE 3. DATES COVERED 00-00-2003 to 00-00-2003 4. TITLE AND SUBTITLE Development of Automated Image Analysis Software for Suspended...objective is to develop automated image analysis software to reduce the effort and time required for manual identification of plankton images. Automated

Some calculations of transonic potential flow for the NACA 64A006 airfoil with oscillating flap

NASA Technical Reports Server (NTRS)

Bennett, R. M.; Bland, S. R.

1978-01-01

A method for calculating the transonic flow over steady and oscillating airfoils was developed by Isogai. It solves the full potential equation with a semi-implicit, time-marching, finite difference technique. Steady flow solutions are obtained from time asymptotic solutions for a steady airfoil. Corresponding oscillatory solutions are obtained by initiating an oscillation and marching in time for several cycles until a converged periodic solution is achieved. In this paper the method is described in general terms, and results are compared with experimental data for both steady flow and for oscillations at several values of reduced frequency. Good agreement for static pressures is shown for subcritical speeds, with increasing deviation as Mach number is increased into the supercritical speed range. Fair agreement with experiment was obtained at high reduced frequencies with larger deviations at low reduced frequencies.

Origanum dictamnus oil vapour suppresses the development of grey mould in eggplant fruit in vitro.

PubMed

Stavropoulou, Andriana; Loulakakis, Kostas; Magan, Naresh; Tzortzakis, Nikos

2014-01-01

Grey mould rot (Botrytis cinerea) development in vitro or in eggplant (Solanum melongena L.) fruit was evaluated after treatment with dittany (Origanum dictamnus L.) oil (DIT) and storage at 12°C and 95% relative humidity during or following exposure to the volatiles. DIT volatiles used in different concentration (0-50-100-250 μL/L) and times of exposure (up to 120 h) examined the effects on pathogen development as well as fruit quality parameters. In vitro, fungal colony growth was inhibited with the application of DIT oil (during or after exposure) and/or time of application. Continuous exposure to oils reduced conidial germination and production with fungistatic effects observed in 250 μL/L. In vivo, fungal lesion growth and conidial production reduced in DIT-treated fruits. Interesting, in fruits preexposed to volatiles before fungal inoculation, DIT application induced fruit resistance against the pathogen, by reduced lesion growth and conidial production. Conidial viability reduced in >100 μL/L DIT oil. Fruits exposed to essential oil did not affect fruit quality related attributes in general, while skin lightness (L value) increased in 50 and 100 μL/L DIT oil. The results of the current study indicated that dittany volatiles may be considered as an alternative food preservative, eliminating disease spread in the storage/transit atmospheres.

Origanum dictamnus Oil Vapour Suppresses the Development of Grey Mould in Eggplant Fruit In Vitro

PubMed Central

Loulakakis, Kostas; Magan, Naresh; Tzortzakis, Nikos

2014-01-01

Grey mould rot (Botrytis cinerea) development in vitro or in eggplant (Solanum melongena L.) fruit was evaluated after treatment with dittany (Origanum dictamnus L.) oil (DIT) and storage at 12°C and 95% relative humidity during or following exposure to the volatiles. DIT volatiles used in different concentration (0-50-100-250 μL/L) and times of exposure (up to 120 h) examined the effects on pathogen development as well as fruit quality parameters. In vitro, fungal colony growth was inhibited with the application of DIT oil (during or after exposure) and/or time of application. Continuous exposure to oils reduced conidial germination and production with fungistatic effects observed in 250 μL/L. In vivo, fungal lesion growth and conidial production reduced in DIT-treated fruits. Interesting, in fruits preexposed to volatiles before fungal inoculation, DIT application induced fruit resistance against the pathogen, by reduced lesion growth and conidial production. Conidial viability reduced in >100 μL/L DIT oil. Fruits exposed to essential oil did not affect fruit quality related attributes in general, while skin lightness (L value) increased in 50 and 100 μL/L DIT oil. The results of the current study indicated that dittany volatiles may be considered as an alternative food preservative, eliminating disease spread in the storage/transit atmospheres. PMID:25254209

Preliminary Multi-Variable Cost Model for Space Telescopes

NASA Technical Reports Server (NTRS)

Stahl, H. Philip; Hendrichs, Todd

2010-01-01

Parametric cost models are routinely used to plan missions, compare concepts and justify technology investments. This paper reviews the methodology used to develop space telescope cost models; summarizes recently published single variable models; and presents preliminary results for two and three variable cost models. Some of the findings are that increasing mass reduces cost; it costs less per square meter of collecting aperture to build a large telescope than a small telescope; and technology development as a function of time reduces cost at the rate of 50% per 17 years.

An approach to enhance the conservation-compatibility of solar energy development.

PubMed

Cameron, D Richard; Cohen, Brian S; Morrison, Scott A

2012-01-01

The rapid pace of climate change poses a major threat to biodiversity. Utility-scale renewable energy development (>1 MW capacity) is a key strategy to reduce greenhouse gas emissions, but development of those facilities also can have adverse effects on biodiversity. Here, we examine the synergy between renewable energy generation goals and those for biodiversity conservation in the 13 M ha Mojave Desert of the southwestern USA. We integrated spatial data on biodiversity conservation value, solar energy potential, and land surface slope angle (a key determinant of development feasibility) and found there to be sufficient area to meet renewable energy goals without developing on lands of relatively high conservation value. Indeed, we found nearly 200,000 ha of lower conservation value land below the most restrictive slope angle (<1%); that area could meet the state of California's current 33% renewable energy goal 1.8 times over. We found over 740,000 ha below the highest slope angle (<5%)--an area that can meet California's renewable energy goal seven times over. Our analysis also suggests that the supply of high quality habitat on private land may be insufficient to mitigate impacts from future solar projects, so enhancing public land management may need to be considered among the options to offset such impacts. Using the approach presented here, planners could reduce development impacts on areas of higher conservation value, and so reduce trade-offs between converting to a green energy economy and conserving biodiversity.

An Approach to Enhance the Conservation-Compatibility of Solar Energy Development

PubMed Central

Cameron, D. Richard; Cohen, Brian S.; Morrison, Scott A.

2012-01-01

The rapid pace of climate change poses a major threat to biodiversity. Utility-scale renewable energy development (>1 MW capacity) is a key strategy to reduce greenhouse gas emissions, but development of those facilities also can have adverse effects on biodiversity. Here, we examine the synergy between renewable energy generation goals and those for biodiversity conservation in the 13 M ha Mojave Desert of the southwestern USA. We integrated spatial data on biodiversity conservation value, solar energy potential, and land surface slope angle (a key determinant of development feasibility) and found there to be sufficient area to meet renewable energy goals without developing on lands of relatively high conservation value. Indeed, we found nearly 200,000 ha of lower conservation value land below the most restrictive slope angle (<1%); that area could meet the state of California’s current 33% renewable energy goal 1.8 times over. We found over 740,000 ha below the highest slope angle (<5%) – an area that can meet California’s renewable energy goal seven times over. Our analysis also suggests that the supply of high quality habitat on private land may be insufficient to mitigate impacts from future solar projects, so enhancing public land management may need to be considered among the options to offset such impacts. Using the approach presented here, planners could reduce development impacts on areas of higher conservation value, and so reduce trade-offs between converting to a green energy economy and conserving biodiversity. PMID:22685568

Timing and rate of Chaparral treatment affects tall fescue seedhead development and pasture plant densities

USDA-ARS?s Scientific Manuscript database

The herbicide Chaparral™ has been shown to suppress seedhead development in tall fescue (Neotyphodium coenophialum) pastures and reduce the symptoms of tall fescue toxicosis in cattle. However, little is known about the logistics of herbicide treatment on tall fescue pastures. The objective of thi...

An improved tri-tube cryogenic gravel sampler.

Treesearch

Fred H. Everest; Carl E. McLemore; John F. Ward

1980-01-01

The tri-tube cryogenic gravel sampler has been improved, and accessories have been developed that increase its reliability and safety of operation, reduce core extraction time, and allow accurate partitioning of cores into subsamples. The improved tri-tube sampler is one of the most versatile and efficient substrate sampling tools yet developed.

Development of a real-time chemical injection system for air-assisted variable-rate sprayers

USDA-ARS?s Scientific Manuscript database

A chemical injection system is an effective method to minimize chemical waste and reduce the environmental pollution in pesticide spray applications. A microprocessor controlled injection system implementing a ceramic piston metering pump was developed to accurately dispense chemicals to be mixed wi...

Optically Based Rapid Screening Method for Proven Optimal Treatment Strategies Before Treatment Begins

DTIC Science & Technology

to rapidly test /screen breast cancer therapeutics as a strategy to streamline drug development and provide individualized treatment. The results...system can therefore be used to streamline pre-clinical drug development, by reducing the number of animals , cost, and time required to screen new drugs

Lie symmetry analysis, explicit solutions and conservation laws for the space-time fractional nonlinear evolution equations

NASA Astrophysics Data System (ADS)

Inc, Mustafa; Yusuf, Abdullahi; Aliyu, Aliyu Isa; Baleanu, Dumitru

2018-04-01

This paper studies the symmetry analysis, explicit solutions, convergence analysis, and conservation laws (Cls) for two different space-time fractional nonlinear evolution equations with Riemann-Liouville (RL) derivative. The governing equations are reduced to nonlinear ordinary differential equation (ODE) of fractional order using their Lie point symmetries. In the reduced equations, the derivative is in Erdelyi-Kober (EK) sense, power series technique is applied to derive an explicit solutions for the reduced fractional ODEs. The convergence of the obtained power series solutions is also presented. Moreover, the new conservation theorem and the generalization of the Noether operators are developed to construct the nonlocal Cls for the equations . Some interesting figures for the obtained explicit solutions are presented.

Developing a performance data suite to facilitate lean improvement in a chemotherapy day unit.

PubMed

Lingaratnam, Senthil; Murray, Danielle; Carle, Amber; Kirsa, Sue W; Paterson, Rebecca; Rischin, Danny

2013-07-01

A multidisciplinary team from the Peter MacCallum Cancer Centre in Melbourne, Australia, developed a performance data suite to support a service improvement project based on lean manufacturing principles in its 19-chair chemotherapy day unit (CDU) and cytosuite chemotherapy production facility. The aims of the project were to reduce patient wait time and improve equity of access to the CDU. A project team consisting of a pharmacist and CDU nurse supported the management team for 10 months in engaging staff and customers to identify waste in processes, analyze root causes, eliminate non-value-adding steps, reduce variation, and level workloads to improve quality and flow. Process mapping, staff and patient tracking and opinion surveys, medical record audits, and interrogation of electronic treatment records were undertaken. This project delivered a 38% reduction in median wait time on the day (from 32 to 20 minutes; P < .01), 7-day reduction in time to commencement of treatment for patients receiving combined chemoradiotherapy regimens (from 25 to 18 days; P < .01), and 22% reduction in wastage associated with expired drug and pharmacy rework (from 29% to 7%; P < .01). Improvements in efficiency enabled the cytosuite to increase the percentage of product manufactured within 10 minutes of appointment times by 29% (from 47% to 76%; P < .01). A lean improvement methodology provided a robust framework for improved understanding and management of complex system constraints within a CDU, resulting in improved access to treatment and reduced waiting times on the day.

Velo and REXAN - Integrated Data Management and High Speed Analysis for Experimental Facilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kleese van Dam, Kerstin; Carson, James P.; Corrigan, Abigail L.

2013-01-10

The Chemical Imaging Initiative at the Pacific Northwest National Laboratory (PNNL) is creating a ‘Rapid Experimental Analysis’ (REXAN) Framework, based on the concept of reusable component libraries. REXAN allows developers to quickly compose and customize high throughput analysis pipelines for a range of experiments, as well as supporting the creation of multi-modal analysis pipelines. In addition, PNNL has coupled REXAN with its collaborative data management and analysis environment Velo to create an easy to use data management and analysis environments for experimental facilities. This paper will discuss the benefits of Velo and REXAN in the context of three examples: PNNLmore » High Resolution Mass Spectrometry - reducing analysis times from hours to seconds, and enabling the analysis of much larger data samples (100KB to 40GB) at the same time · ALS X-Ray tomography - reducing analysis times of combined STXM and EM data collected at the ALS from weeks to minutes, decreasing manual work and increasing data volumes that can be analysed in a single step ·Multi-modal nano-scale analysis of STXM and TEM data - providing a semi automated process for particle detection The creation of REXAN has significantly shortened the development time for these analysis pipelines. The integration of Velo and REXAN has significantly increased the scientific productivity of the instruments and their users by creating easy to use data management and analysis environments with greatly reduced analysis times and improved analysis capabilities.« less

Systematic development of reduced reaction mechanisms for dynamic modeling

NASA Technical Reports Server (NTRS)

Frenklach, M.; Kailasanath, K.; Oran, E. S.

1986-01-01

A method for systematically developing a reduced chemical reaction mechanism for dynamic modeling of chemically reactive flows is presented. The method is based on the postulate that if a reduced reaction mechanism faithfully describes the time evolution of both thermal and chain reaction processes characteristic of a more complete mechanism, then the reduced mechanism will describe the chemical processes in a chemically reacting flow with approximately the same degree of accuracy. Here this postulate is tested by producing a series of mechanisms of reduced accuracy, which are derived from a full detailed mechanism for methane-oxygen combustion. These mechanisms were then tested in a series of reactive flow calculations in which a large-amplitude sinusoidal perturbation is applied to a system that is initially quiescent and whose temperature is high enough to start ignition processes. Comparison of the results for systems with and without convective flow show that this approach produces reduced mechanisms that are useful for calculations of explosions and detonations. Extensions and applicability to flames are discussed.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shoaf, S.; APS Engineering Support Division

A real-time image analysis system was developed for beam imaging diagnostics. An Apple Power Mac G5 with an Active Silicon LFG frame grabber was used to capture video images that were processed and analyzed. Software routines were created to utilize vector-processing hardware to reduce the time to process images as compared to conventional methods. These improvements allow for more advanced image processing diagnostics to be performed in real time.

Unlocking the riddle of time in learning disability.

PubMed

Owen, Ann L; Wilson, Rebecca R

2006-03-01

People with learning disabilities often have difficulties understanding abstract concepts such as the concept of time yet research in this area is scarce. Not only does the development of an understanding of the concept of time enable us to predict future events, order past events and give us a sense of control over current events, it also serves to contribute to the very essence of our understanding of a sense of ourselves. It seems reasonable to suggest that the converse may be true for people who are not able to develop this concept. Time perception and understanding are complex cognitive processes. It is suggested that facilitating this development and managing associated difficulties may be achieved by focusing on the practical applications of time in everyday life. Improving time perception abilities may reduce feelings of powerlessness and anxiety and increase feelings of self-efficacy but research is needed to evaluate this.

Implementing real-time robotic systems using CHIMERA II

NASA Technical Reports Server (NTRS)

Stewart, David B.; Schmitz, Donald E.; Khosla, Pradeep K.

1990-01-01

A description is given of the CHIMERA II programming environment and operating system, which was developed for implementing real-time robotic systems. Sensor-based robotic systems contain both general- and special-purpose hardware, and thus the development of applications tends to be a time-consuming task. The CHIMERA II environment is designed to reduce the development time by providing a convenient software interface between the hardware and the user. CHIMERA II supports flexible hardware configurations which are based on one or more VME-backplanes. All communication across multiple processors is transparent to the user through an extensive set of interprocessor communication primitives. CHIMERA II also provides a high-performance real-time kernel which supports both deadline and highest-priority-first scheduling. The flexibility of CHIMERA II allows hierarchical models for robot control, such as NASREM, to be implemented with minimal programming time and effort.

Real Time Data Management for Estimating Probabilities of Incidents and Near Misses

NASA Astrophysics Data System (ADS)

Stanitsas, P. D.; Stephanedes, Y. J.

2011-08-01

Advances in real-time data collection, data storage and computational systems have led to development of algorithms for transport administrators and engineers that improve traffic safety and reduce cost of road operations. Despite these advances, problems in effectively integrating real-time data acquisition, processing, modelling and road-use strategies at complex intersections and motorways remain. These are related to increasing system performance in identification, analysis, detection and prediction of traffic state in real time. This research develops dynamic models to estimate the probability of road incidents, such as crashes and conflicts, and incident-prone conditions based on real-time data. The models support integration of anticipatory information and fee-based road use strategies in traveller information and management. Development includes macroscopic/microscopic probabilistic models, neural networks, and vector autoregressions tested via machine vision at EU and US sites.

THE CHOICE OF REAL-TIME CONTROL STRATEGY FOR COMBINED SEWER OVERFLOW CONTROL

EPA Science Inventory

This paper focuses on the strategies used to operate a collection system in real-time control (RTC) in order to optimize use of system capacity and to reduce the cost of long-term combined sewer overflow (CSO) control. Three RTC strategies were developed and analyzed based on the...

Experts in Fast-Ball Sports Reduce Anticipation Timing Cost by Developing Inhibitory Control

ERIC Educational Resources Information Center

Nakamoto, Hiroki; Mori, Shiro

2012-01-01

The present study was conducted to examine the relationship between expertise in movement correction and rate of movement reprogramming within limited time periods, and to clarify the specific cognitive processes regarding superior reprogramming ability in experts. Event-related potentials (ERPs) were recorded in baseball experts (n = 7) and…

On the Poggendorff Experiment

ERIC Educational Resources Information Center

Coelho, Ricardo Lopes; Silva, P. A. S.; Borges, Paulo de Faria

2015-01-01

Poggendorff showed experimentally, in the middle of the 19th century, that the weight of an Atwood machine is reduced when it is brought to motion. His experiment has been revisited from time to time, making use of instrumentation that reflects the technological development of the moment. In this paper, the evolution of the experiment is briefly…

Real-Time On-Board Processing Validation of MSPI Ground Camera Images

NASA Technical Reports Server (NTRS)

Pingree, Paula J.; Werne, Thomas A.; Bekker, Dmitriy L.

2010-01-01

The Earth Sciences Decadal Survey identifies a multiangle, multispectral, high-accuracy polarization imager as one requirement for the Aerosol-Cloud-Ecosystem (ACE) mission. JPL has been developing a Multiangle SpectroPolarimetric Imager (MSPI) as a candidate to fill this need. A key technology development needed for MSPI is on-board signal processing to calculate polarimetry data as imaged by each of the 9 cameras forming the instrument. With funding from NASA's Advanced Information Systems Technology (AIST) Program, JPL is solving the real-time data processing requirements to demonstrate, for the first time, how signal data at 95 Mbytes/sec over 16-channels for each of the 9 multiangle cameras in the spaceborne instrument can be reduced on-board to 0.45 Mbytes/sec. This will produce the intensity and polarization data needed to characterize aerosol and cloud microphysical properties. Using the Xilinx Virtex-5 FPGA including PowerPC440 processors we have implemented a least squares fitting algorithm that extracts intensity and polarimetric parameters in real-time, thereby substantially reducing the image data volume for spacecraft downlink without loss of science information.

The cost analysis of material handling in Chinese traditional praying paper production plant

NASA Astrophysics Data System (ADS)

Nasution, H.; Budiman, I.; Salim, A.

2018-02-01

Chinese traditional praying paper industry is an industry which produced Chinese traditional religion praying paper. This kind of industry is rarely examined since it was only in Small and Medium Enterprise (SME’s- form). This industry produced various kinds of Chinese traditional paper products. The purpose of this research is to increase the amount of production, reduce waiting time and moving time, and reduce material handling cost. The research was conducted at prime production activities, consists of: calculate the capacity of the material handler, the frequency of movement, cost of material handling, and total cost of material handling. This displacement condition leads to an ineffective and inefficient production process. The alternative was developed using production judgment and aisle standard. Based on the observation results, it is possible to reduce displacement in the production. Using alternative which by-passed displacement from a rolled paper in the temporary warehouse to cutting and printing workstation, it can reduce material handling cost from 2.26 million rupiahs to 2.00 million rupiahs only for each batch of production. This result leads to increasing of production quantity, reducing waiting and moving time about 10% from the current condition.

Impact of Smartphone Applications on Timing of Endovascular Therapy for Ischemic Stroke: A Preliminary Study.

PubMed

Alotaibi, Naif M; Sarzetto, Francesca; Guha, Daipayan; Lu, Michael; Bodo, Andre; Gupta, Shaurya; Dyer, Erin; Howard, Peter; da Costa, Leodante; Swartz, Richard H; Boyle, Karl; Nathens, Avery B; Yang, Victor X D

2017-11-01

The metrics of imaging-to-puncture and imaging-to-reperfusion were recently found to be associated with the clinical outcomes of endovascular thrombectomy for acute ischemic stroke. However, measures for improving workflow within hospitals to achieve better timing results are largely unexplored for endovascular therapy. The aim of this study was to examine our experience with a novel smartphone application developed in house to improve our timing metrics for endovascular treatment. We developed an encrypted smartphone application connecting all stroke team members to expedite conversations and to provide synchronized real-time updates on the time window from stroke onset to imaging and to puncture. The effects of the application on the timing of endovascular therapy were evaluated with a secondary analysis of our single-center cohort. Our primary outcome was imaging-to-puncture time. We assessed the outcomes with nonparametric tests of statistical significance. Forty-five patients met our criteria for analysis among 66 consecutive patients with acute ischemic stroke who received endovascular therapy at our institution. After the implementation of the smartphone application, imaging-to-puncture time was significantly reduced (preapplication median time, 127 minutes; postapplication time, 69 minutes; P < 0.001). Puncture-to-reperfusion time was not affected by the application use (42 minutes vs. 36 minutes). The use of smartphone applications may reduce treatment times for endovascular therapy in acute ischemic stroke. Further studies are needed to confirm our findings. Copyright © 2017. Published by Elsevier Inc.

Hamstring Muscle Fatigue and Central Motor Output during a Simulated Soccer Match

PubMed Central

Marshall, Paul W. M.; Lovell, Ric; Jeppesen, Gitte K.; Andersen, Kristoffer; Siegler, Jason C.

2014-01-01

Purpose To examine changes in hamstring muscle fatigue and central motor output during a 90-minute simulated soccer match, and the concomitant changes in hamstring maximal torque and rate of torque development. Method Eight amateur male soccer players performed a 90-minute simulated soccer match, with measures performed at the start of and every 15-minutes during each half. Maximal torque (Nm) and rate of torque development (RTD; Nm.s–1) were calculated from maximal isometric knee flexor contractions performed at 10° of flexion. Hamstring peripheral fatigue was assessed from changes in the size and shape of the resting twitch (RT). Hamstring central motor output was quantified from voluntary activation (%) and normalized biceps femoris (BF) and medial hamstrings (MH) electromyographic amplitudes (EMG/M). Results Maximal torque was reduced at 45-minutes by 7.6±9.4% (p<0.05). RTD in time intervals of 0–25, 0–50, and 0–75 ms post-contraction onset were reduced after 15-minutes in the first-half between 29.6 to 46.2% (p<0.05), and were further reduced at the end of the second-half (p<0.05). Maximal EMG/M was reduced for biceps femoris only concomitant to the time-course of reductions in maximal torque (p = 0.007). The rate of EMG rise for BF and MH was reduced in early time periods (0–75 ms) post-contraction onset (p<0.05). No changes were observed for the size and shape of the RT, indicating no hamstring peripheral fatigue. Conclusion Centrally mediated reductions in maximal torque and rate of torque development provide insight into factors that may explain hamstring injury risk during soccer. Of particular interest were early reductions during the first-half of hamstring rate of torque development, and the decline in maximal EMG/M of biceps femoris in the latter stages of the half. These are important findings that may help explain why the hamstrings are particularly vulnerable to strain injury during soccer. PMID:25047547

Fear, food and sexual ornamentation: plasticity of colour development in Trinidadian guppies

PubMed Central

Ruell, E. W.; Handelsman, C. A.; Hawkins, C. L.; Sofaer, H. R.; Ghalambor, C. K.; Angeloni, L.

2013-01-01

The evolution of male ornamentation often reflects compromises between sexual and natural selection, but it may also be influenced by phenotypic plasticity. We investigated the developmental plasticity of male colour ornamentation in Trinidadian guppies in response to two environmental variables that covary in nature: predation risk and food availability. We found that exposure to chemical predator cues delayed the development of pigment-based colour elements, which are conspicuous to visual-oriented predators. Predator cues also reduced the size of colour elements at the time of maturity and caused adult males to be less colourful. To the best of our knowledge, these findings provide the first example of a plastic reduction in the development of a sexually selected male ornament in response to predator cues. The influence of predator cues on ornamentation probably affects individual fitness by reducing conspicuousness to predators, but could reduce attractiveness to females. Reduced food availability during development caused males to delay the development of colour elements and mature later, probably reflecting a physiological constraint, but their coloration at maturity and later in adulthood was largely unaffected, suggesting that variation in food quantity without variation in quality does not contribute to condition dependence of the trait. PMID:23466982

Cost and Time Effectiveness Analysis of a Telemedicine Service in Bangladesh.

PubMed

Sorwar, Golam; Rahamn, Md Mustafizur; Uddin, Ramiz; Hoque, Md Rakibul

2016-01-01

Telemedicine has great potential to overcome geographical barriers to providing access to equal health care services, particularly for people living in remote and rural areas in developing countries like Bangladesh. A number of telemedicine systems have been implemented in Bangladesh. However, no significant studies have been conducted to determine either their cost effectiveness or efficiency in reducing travel time required by patients. In addition, very few studies have analyzed the attitude and level of satisfaction of telemedicine service recipients in Bangladesh. The aim of this study was to analyze the cost and time effectiveness of a telemedicine service, implemented through locally developed PC based diagnostic equipment and software in Bangladesh, compared to conventional means of providing those services. The study revealed that the introduced telemedicine service reduced cost and travel time on average by 56% and 94% respectively compared to its counterpart conventional approach. The study also revealed that majority of users were highly satisfied with the newly introduced telemedicine service. Therefore, the introduced telemedicine service can be considered as a low cost and time efficient health service solution to improve health care facilities in the remote rural areas in Bangladesh.

Cure Cycle Optimization of Rapidly Cured Out-Of-Autoclave Composites.

PubMed

Dong, Anqi; Zhao, Yan; Zhao, Xinqing; Yu, Qiyong

2018-03-13

Out-of-autoclave prepreg typically needs a long cure cycle to guarantee good properties as the result of low processing pressure applied. It is essential to reduce the manufacturing time, achieve real cost reduction, and take full advantage of out-of-autoclave process. The focus of this paper is to reduce the cure cycle time and production cost while maintaining high laminate quality. A rapidly cured out-of-autoclave resin and relative prepreg were independently developed. To determine a suitable rapid cure procedure for the developed prepreg, the effect of heating rate, initial cure temperature, dwelling time, and post-cure time on the final laminate quality were evaluated and the factors were then optimized. As a result, a rapid cure procedure was determined. The results showed that the resin infiltration could be completed at the end of the initial cure stage and no obvious void could be seen in the laminate at this time. The laminate could achieve good internal quality using the optimized cure procedure. The mechanical test results showed that the laminates had a fiber volume fraction of 59-60% with a final glass transition temperature of 205 °C and excellent mechanical strength especially the flexural properties.

Cure Cycle Optimization of Rapidly Cured Out-Of-Autoclave Composites

PubMed Central

Dong, Anqi; Zhao, Yan; Zhao, Xinqing; Yu, Qiyong

2018-01-01

Out-of-autoclave prepreg typically needs a long cure cycle to guarantee good properties as the result of low processing pressure applied. It is essential to reduce the manufacturing time, achieve real cost reduction, and take full advantage of out-of-autoclave process. The focus of this paper is to reduce the cure cycle time and production cost while maintaining high laminate quality. A rapidly cured out-of-autoclave resin and relative prepreg were independently developed. To determine a suitable rapid cure procedure for the developed prepreg, the effect of heating rate, initial cure temperature, dwelling time, and post-cure time on the final laminate quality were evaluated and the factors were then optimized. As a result, a rapid cure procedure was determined. The results showed that the resin infiltration could be completed at the end of the initial cure stage and no obvious void could be seen in the laminate at this time. The laminate could achieve good internal quality using the optimized cure procedure. The mechanical test results showed that the laminates had a fiber volume fraction of 59–60% with a final glass transition temperature of 205 °C and excellent mechanical strength especially the flexural properties. PMID:29534048

Umbilical Connect Techniques Improvement-Technology Study

NASA Technical Reports Server (NTRS)

Valkema, Donald C.

1972-01-01

The objective of this study was to develop concepts, specifications, designs, techniques, and procedures capable of significantly reducing the time required to connect and verify umbilicals for ground services to the space shuttle. The desired goal was to reduce the current time requirement of several shifts for the Saturn 5/Apollo to an elapsed time of less than one hour to connect and verify all of the space shuttle ground service umbilicals. The study was conducted in four phases: (1) literature and hardware examination, (2) concept development, (3) concept evaluation and tradeoff analysis, and (4) selected concept design. The final product of this study was a detail design of a rise-off disconnect panel prototype test specimen for a LO2/LH2 booster (or an external oxygen/hydrogen tank for an orbiter), a detail design of a swing-arm mounted preflight umbilical carrier prototype test specimen, and a part 1 specification for the umbilical connect and verification design for the vehicles as defined in the space shuttle program.

The Relationship of Cow Comfort and Flooring to Lameness Disorders in Dairy Cattle.

PubMed

Endres, Marcia I

2017-07-01

Cow comfort and flooring contribute to lameness incidence in dairy herds. The trigger factors for lameness can all be exacerbated by poor cow comfort. Reduced cow comfort influences lameness incidence by increasing the risk for development of new cases and the time it takes for a cow to recover. Reduction in resting time will increase the cow's exposure to hard flooring surfaces. Many factors are associated with lameness prevalence. Housing and management factors should be optimized to reduce lameness incidence on dairy farms. Copyright © 2017 Elsevier Inc. All rights reserved.

Advanced Guidance and Control Project for Reusable Launch Vehicles

NASA Technical Reports Server (NTRS)

Hanson, John M.

2000-01-01

The goals of this project are to significantly reduce the time and cost associated with guidance and control design for reusable launch vehicles, and to increase their safety and reliability. Success will lead to reduced cycle times during vehicle design and to reduced costs associated with flying to new orbits, with new payloads, and with modified vehicles. Success will also lead to more robustness to unforeseen circumstances in flight thereby enhancing safety and reducing risk. There are many guidance and control methods available that hold some promise for improvement in the desired areas. Investigators are developing a representative set of independent guidance and control methods for this project. These methods are being incorporated into a high-fidelity off is being conducted across a broad range of flight requirements. The guidance and control methods that perform the best will have demonstrated the desired qualities.

Configurable technology development for reusable control and monitor ground systems

NASA Technical Reports Server (NTRS)

Uhrlaub, David R.

1994-01-01

The control monitor unit (CMU) uses configurable software technology for real-time mission command and control, telemetry processing, simulation, data acquisition, data archiving, and ground operations automation. The base technology is currently planned for the following control and monitor systems: portable Space Station checkout systems; ecological life support systems; Space Station logistics carrier system; and the ground system of the Delta Clipper (SX-2) in the Single-Stage Rocket Technology program. The CMU makes extensive use of commercial technology to increase capability and reduce development and life-cycle costs. The concepts and technology are being developed by McDonnell Douglas Space and Defense Systems for the Real-Time Systems Laboratory at NASA's Kennedy Space Center under the Payload Ground Operations Contract. A second function of the Real-Time Systems Laboratory is development and utilization of advanced software development practices.

Health risks, correlates, and interventions to reduce sedentary behavior in young people.

PubMed

Salmon, Jo; Tremblay, Mark S; Marshall, Simon J; Hume, Clare

2011-08-01

Opportunities for young people to be sedentary have increased during leisure time, study time, and transportation time. This review paper focuses on sedentary behaviors among young people aged 2-18 years and includes evidence of the relationship between sedentary behavior and health risk indicators, an overview of public health recommendations, the prevalence of key sedentary behaviors, evidence of correlates of sedentary behavior and the effectiveness of interventions to reduce sedentary behaviors. Although this is a narrative style review and not systematic, where possible, findings from relevant review papers were summarized and a search of more recent literature was performed using computer-based databases such as PubMed, Google Scholar, ERIC, PsycINFO, Social Science Index, SportDiscus, and Health Reference Center - Academic. Young people spend 2-4 hours per day in screen-based behaviors and 5-10 hours per day sedentary. Ethnicity, sociodemographic status, having a TV set in the bedroom, and parental behavior appear to be the most consistent correlates of TV viewing time; however, few recent studies aiming to reduce TV viewing or sedentary time among young people have been successful. A growing body of evidence supports the development of public health recommendations to limit the time spent in screen-based behaviors. More research is needed to examine the prospective and experimental evidence of associations between overall sedentary time and health, determinants of sedentary behaviors other than screen-based behaviors, and interventions to reduce overall sedentary time or even alternative sedentary behaviors, such as transport- or education-related sitting time. Copyright © 2011 American Journal of Preventive Medicine. Published by Elsevier Inc. All rights reserved.

Decrease in coronary vascular volume in systole augments cardiac contraction.

PubMed

Willemsen, M J; Duncker, D J; Krams, R; Dijkman, M A; Lamberts, R R; Sipkema, P; Westerhof, N

2001-08-01

Coronary arterial inflow is impeded and venous outflow is increased as a result of the decrease in coronary vascular volume due to cardiac contraction. We evaluated whether cardiac contraction is influenced by interfering with the changes of the coronary vascular volume over the heart cycle. Length-tension relationships were determined in Tyrode-perfused rat papillary muscle and when coronary vascular volume changes were partly inhibited by filling it with congealed gelatin or perfusing it with a high viscosity dextran buffer. Also, myocyte thickening during contraction was reduced by placing a silicon tube around the muscle. Increasing perfusion pressure from 8 to 80 cmH2O, increased developed tension by approximately 40%. When compared with the low perfusion state, developed tension of the gelatin-filled vasculature was reduced to 43 +/- 6% at the muscle length where the muscle generates the largest developed tension (n = 5, means +/- SE). Dextran reduced developed tension to 73 +/- 6% (n = 6). The silicon tube, in low perfusion state, reduced the developed tension to 83 +/- 7% (n = 4) of control. Time-control and oxygen-lowering experiments show that the findings are based on mechanical effects. Thus interventions to prevent myocyte thickening reduce developed tension. We hypothesize that when myocyte thickening is prevented, intracellular pressure increases and counteracts the force produced by the contractile apparatus. We conclude that emptying of the coronary vasculature serves a physiological purpose by facilitating cardiomyocyte thickening thereby augmenting force development.

Development of a prototype real-time automated filter for operational deep space navigation

NASA Technical Reports Server (NTRS)

Masters, W. C.; Pollmeier, V. M.

1994-01-01

Operational deep space navigation has been in the past, and is currently, performed using systems whose architecture requires constant human supervision and intervention. A prototype for a system which allows relatively automated processing of radio metric data received in near real-time from NASA's Deep Space Network (DSN) without any redesign of the existing operational data flow has been developed. This system can allow for more rapid response as well as much reduced staffing to support mission navigation operations.

Development of a Miniature Mass Spectrometer and an Automated Detector for Sampling Explosive Materials

PubMed Central

Hashimoto, Yuichiro

2017-01-01

The development of a robust ionization source using the counter-flow APCI, miniature mass spectrometer, and an automated sampling system for detecting explosives are described. These development efforts using mass spectrometry were made in order to improve the efficiencies of on-site detection in areas such as security, environmental, and industrial applications. A development team, including the author, has struggled for nearly 20 years to enhance the robustness and reduce the size of mass spectrometers to meet the requirements needed for on-site applications. This article focuses on the recent results related to the detection of explosive materials where automated particle sampling using a cyclone concentrator permitted the inspection time to be successfully reduced to 3 s. PMID:28337396

Evaluation of Heliostat Standby Aiming Strategies to Reduce Avian Flux Hazards and Impacts on Operational Performance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wendelin, Timothy J; Ho, Clifford K.; Horstman, Luke

This paper presents a study of alternative heliostat standby aiming strategies and their impact on avian flux hazards and operational performance of a concentrating solar power plant. A mathematical model was developed that predicts the bird-feather temperature as a function of solar irradiance, thermal emittance, convection, and thermal properties of the feather. The irradiance distribution in the airspace above the Ivanpah Unit 2 heliostat field was simulated using a ray-trace model for two different times of the day, four days of the year, and nine different standby aiming strategies. The impact of the alternative aiming strategies on operational performance wasmore » assessed by comparing the heliostat slew times from standby position to the receiver for the different aiming strategies. Increased slew times increased a proxy start-up time that reduced the simulated annual energy production. Results showed that spreading the radial aim points around the receiver to a distance of ~150 m or greater reduced the hazardous exposure times that the feather temperature exceeded the hazard metric of 160 degrees C. The hazardous exposure times were reduced by ~23% and 90% at a radial spread of aim points extending to 150 m and 250 m, respectively, but the simulated annual energy production decreased as a result of increased slew times. Single point-focus aiming strategies were also evaluated, but these strategies increased the exposure hazard relative to other aiming strategies.« less

Parallel MR imaging: a user's guide.

PubMed

Glockner, James F; Hu, Houchun H; Stanley, David W; Angelos, Lisa; King, Kevin

2005-01-01

Parallel imaging is a recently developed family of techniques that take advantage of the spatial information inherent in phased-array radiofrequency coils to reduce acquisition times in magnetic resonance imaging. In parallel imaging, the number of sampled k-space lines is reduced, often by a factor of two or greater, thereby significantly shortening the acquisition time. Parallel imaging techniques have only recently become commercially available, and the wide range of clinical applications is just beginning to be explored. The potential clinical applications primarily involve reduction in acquisition time, improved spatial resolution, or a combination of the two. Improvements in image quality can be achieved by reducing the echo train lengths of fast spin-echo and single-shot fast spin-echo sequences. Parallel imaging is particularly attractive for cardiac and vascular applications and will likely prove valuable as 3-T body and cardiovascular imaging becomes part of standard clinical practice. Limitations of parallel imaging include reduced signal-to-noise ratio and reconstruction artifacts. It is important to consider these limitations when deciding when to use these techniques. (c) RSNA, 2005.

Effect of Debagging Time on Pigment Patterns in the Peel and Sugar and Organic Acid Contents in the Pulp of ‘Golden Delicious’ and ‘Qinguan’ Apple Fruit at Mid and Late Stages of Development

PubMed Central

Jing, Chenjuan; Ma, Changqing; Zhang, Juan; Jing, Shujuan; Jiang, Xiaobing; Yang, Yazhou; Zhao, Zhengyang

2016-01-01

This study examined the effect of debagging time on color and flavor / taste compounds in the non-red apple cultivar ‘Golden Delicious’ and red cultivar ‘Qinguan’ at mid and late stages of fruit development. Debagging briefly improved the red color in both cultivars, the peel of ‘Golden Delicious’ presenting pale-pink hue. However, rapid anthocyanin accumulation occurred in apple peel at a specific time (after 179 days after flowering (DAF) in ‘Qinguan’) and was unaltered by debagging time in the red cultivar ‘Qinguan’. Furthermore, untimely debagging had a detrimental effect on the content of anthocyanin. All sugars increased and organic acids decreased in apple pulp at mid to late stages of development. Bagging treatment reduced the content of most sugars and organic acids, as well as, the overall total. However, glucose and citric acid contents were higher in bagged fruit than non-bagged fruit; the maximum occurred in T7 treatment that was no-debagging at DAF 159 / 196 (‘Golden delicious’ / ‘Qinguan’), i.e., 24.35 and 0.07 mg g-1 FW in ‘Golden delicious’, and 38.86 and 0.06 mg g-1 FW in ‘Qinguan’, respectively. In a word, bagging treatment can alter the pattern of peel color development in apple fruit; however, it remains difficult to alter the timing of rapid anthocyanin accumulation as it is regulated solely by development. Moreover, bagging treatment reduced the total accumulation of sugars and organic acids, and even the over total in pulp, but increased the glucose and citric acid contents in apple pulp. PMID:27788164

Impacts of household coal and biomass combustion on indoor and ambient air quality in China: Current status and implication.

PubMed

Li, Qing; Jiang, Jingkun; Wang, Shuxiao; Rumchev, Krassi; Mead-Hunter, Ryan; Morawska, Lidia; Hao, Jiming

2017-01-15

This review briefly introduces current status of indoor and ambient air pollution originating from household coal and biomass combustion in mainland China. Owing to low combustion efficiency, emissions of CO, PM 2.5 , black carbon (BC), and polycyclic aromatic hydrocarbons have significant adverse consequences for indoor and ambient air qualities, resulting in relative contributions of more than one-third in all anthropogenic emissions. Their contributions are higher in less economically developed regions, such as Guizhou (61% PM 2.5 , 80% BC), than that in more developed regions, such as Shanghai (4% PM 2.5 , 17% BC). Chimneys can reduce ~80% indoor PM 2.5 level when burning dirty solid fuels, such as plant materials. Due to spending more time near stoves, housewives suffer much more (~2 times) PM 2.5 than the adult men, especially in winter in northern China (~4 times). Improvement of stove combustion/thermal efficiencies and solid fuel quality are the two essential methods to reduce pollutant emissions. PM 2.5 and BC emission factors (EFs) have been identified to increase with volatile matter content in traditional stove combustion. EFs of dirty fuels are two orders higher than that of clean ones. Switching to clean ones, such as semi-coke briquette, was identified to be a feasible path for reducing >90% PM 2.5 and BC emissions. Otherwise, improvement of thermal and combustion efficiencies by using under-fire technology can reduce ~50% CO 2 , 87% NH 3 , and 80% PM 2.5 and BC emissions regardless of volatile matter content in solid fuel. However, there are still some knowledge gaps, such as, inventory for the temporal impact of household combustion on air quality, statistic data for deployed clean solid fuels and advanced stoves, and the effect of socioeconomic development. Additionally, further technology research for reducing air pollution emissions is urgently needed, especially low cost and clean stove when burning any type of solid fuel. Furthermore, emission-abatement oriented policy should base on sound scientific evidence to significantly reduce pollutant emissions. Copyright © 2016 Elsevier B.V. All rights reserved.

Reducing youth screen time: qualitative metasynthesis of findings on barriers and facilitators.

PubMed

Minges, Karl E; Owen, Neville; Salmon, Jo; Chao, Ariana; Dunstan, David W; Whittemore, Robin

2015-04-01

An integrated perspective on the relevant qualitative findings on the experience of screen time in youth can inform the development of hypotheses to be tested in future research and can guide the development of interventions to decrease sedentary behavior. The purpose of this qualitative metasynthesis was to explore parent, youth, and educational professionals' perceptions of barriers to, and facilitators of, reducing youth screen time. Qualitative metasynthesis techniques were used to analyze and synthesize 15 qualitative studies of screen time among youth (11-18 years) meeting inclusion criteria. The phrases, quotes, and/or author interpretations (i.e., theme or subtheme) were recorded in a data display matrix to facilitate article comparisons. Codes were collapsed into 23 categories of similar conceptual meaning and 3 overarching themes were derived using thematic analysis procedures. Study sample sizes ranged from 6 to 270 participants from 6 countries. Data collection methods included focus groups (n = 6), interviews (n = 4), focus group and interviews (n = 4), and naturalistic observation (n = 1) with youth and/or parents. Data analysis techniques included thematic analysis (n = 9), content analysis (n = 3), grounded theory (n = 1), observation (n = 1), and interpretive phenomenological analysis (n = 1). Three thematic categories were identified: (a) youth's norms-screen time is an integral part of daily life, and facilitates opportunities for entertainment, social interaction, and escapism; (b) family dynamics and parental roles-parents are conflicted and send mixed messages about the appropriate uses and amounts of screen time; and, (c) resources and environment-engagement in screen time is dependent on school, community, neighborhood, and home environmental contexts. Screen time is an established norm in many youth cultures, presenting barriers to behavior change. Parents recognize the importance of reducing youth screen time, but model and promote engagement themselves. For youth and parents, mutually agreed rules, limits, and parental monitoring of screen time were perceived as likely to be effective. (c) 2015 APA, all rights reserved).

Reducing Youth Screen Time: Qualitative Metasynthesis of Findings on Barriers and Facilitators

PubMed Central

Minges, Karl E.; Salmon, Jo; Dunstan, David W.; Owen, Neville; Chao, Ariana; Whittemore, Robin

2015-01-01

Objective An integrated perspective on the relevant qualitative findings on the experience of screen time in youth can inform the development of hypotheses to be tested in future research and can guide the development of interventions to decrease sedentary behavior. The purpose of this qualitative metasynthesis was to explore parent, youth, and educational professionals’ perceptions of barriers to, and facilitators of, reducing youth screen time. Method Qualitative metasynthesis techniques were used to analyze and synthesize 15 qualitative studies of screen time among youth (11–18 years) meeting inclusion criteria. The phrases, quotes, and/or author interpretations (i.e., theme or subtheme) were recorded in a data display matrix to facilitate article comparisons. Codes were collapsed into 23 categories of similar conceptual meaning and 3 overarching themes were derived using thematic analysis procedures. Results Study sample sizes ranged from 6 to 270 participants from 6 countries. Data collection methods included focus groups (n = 6), interviews (n = 4), focus group and interviews (n = 4), and naturalistic observation (n = 1) with youth and/or parents. Data analysis techniques included thematic analysis (n = 9), content analysis (n = 3), grounded theory (n = 1), observation (n = 1), and interpretive phenomenological analysis (n = 1). Three thematic categories were identified: (a) youth’s norms—screen time is an integral part of daily life, and facilitates opportunities for entertainment, social interaction, and escapism; (b) family dynamics and parental roles—parents are conflicted and send mixed messages about the appropriate uses and amounts of screen time; and, (c) resources and environment—engagement in screen time is dependent on school, community, neighborhood, and home environmental contexts. Conclusions Screen time is an established norm in many youth cultures, presenting barriers to behavior change. Parents recognize the importance of reducing youth screen time, but model and promote engagement themselves. For youth and parents, mutually agreed rules, limits, and parental monitoring of screen time were perceived as likely to be effective. PMID:25822054

SU-E-I-37: Low-Dose Real-Time Region-Of-Interest X-Ray Fluoroscopic Imaging with a GPU-Accelerated Spatially Different Bilateral Filtering

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chung, H; Lee, J; Pua, R

2014-06-01

Purpose: The purpose of our study is to reduce imaging radiation dose while maintaining image quality of region of interest (ROI) in X-ray fluoroscopy. A low-dose real-time ROI fluoroscopic imaging technique which includes graphics-processing-unit- (GPU-) accelerated image processing for brightness compensation and noise filtering was developed in this study. Methods: In our ROI fluoroscopic imaging, a copper filter is placed in front of the X-ray tube. The filter contains a round aperture to reduce radiation dose to outside of the aperture. To equalize the brightness difference between inner and outer ROI regions, brightness compensation was performed by use of amore » simple weighting method that applies selectively to the inner ROI, the outer ROI, and the boundary zone. A bilateral filtering was applied to the images to reduce relatively high noise in the outer ROI images. To speed up the calculation of our technique for real-time application, the GPU-acceleration was applied to the image processing algorithm. We performed a dosimetric measurement using an ion-chamber dosimeter to evaluate the amount of radiation dose reduction. The reduction of calculation time compared to a CPU-only computation was also measured, and the assessment of image quality in terms of image noise and spatial resolution was conducted. Results: More than 80% of dose was reduced by use of the ROI filter. The reduction rate depended on the thickness of the filter and the size of ROI aperture. The image noise outside the ROI was remarkably reduced by the bilateral filtering technique. The computation time for processing each frame image was reduced from 3.43 seconds with single CPU to 9.85 milliseconds with GPU-acceleration. Conclusion: The proposed technique for X-ray fluoroscopy can substantially reduce imaging radiation dose to the patient while maintaining image quality particularly in the ROI region in real-time.« less

Popcorn and a Movie--Opening Diversity Conversations across the State

ERIC Educational Resources Information Center

Ingram, Patreese D.

2013-01-01

Building the cultural competencies of Extension educators to work effectively with increasingly diverse audiences has become an important goal and a timely focus for professional development. Yet reduced budgets and reductions in staff are challenging the ability to provide professional development in the traditional face-to-face delivery method.…

Biochar research activities and their relation to development and environmental quality: A meta-analysis

USDA-ARS?s Scientific Manuscript database

Developing agricultural technologies to double food supply by 2030 and at the same time reducing the emissions of greenhouse gases from agriculture will be challenging, but an imperative issue for the 21st century. The production and application of biochar could contribute to achieving these goals, ...

A view in the mirror - Or through the looking glass. [history of development of optical telescopes

NASA Technical Reports Server (NTRS)

Meinel, A. B.; Meinel, M. P.

1986-01-01

The development of optical telescopes from the age of astrology to those of today and the future is discussed. The rationales for changes in the design of telescopes during this time are explored. The cost drivers, and how to reduce them, are also discussed.

Use of high performance networks and supercomputers for real-time flight simulation

NASA Technical Reports Server (NTRS)

Cleveland, Jeff I., II

1993-01-01

In order to meet the stringent time-critical requirements for real-time man-in-the-loop flight simulation, computer processing operations must be consistent in processing time and be completed in as short a time as possible. These operations include simulation mathematical model computation and data input/output to the simulators. In 1986, in response to increased demands for flight simulation performance, NASA's Langley Research Center (LaRC), working with the contractor, developed extensions to the Computer Automated Measurement and Control (CAMAC) technology which resulted in a factor of ten increase in the effective bandwidth and reduced latency of modules necessary for simulator communication. This technology extension is being used by more than 80 leading technological developers in the United States, Canada, and Europe. Included among the commercial applications are nuclear process control, power grid analysis, process monitoring, real-time simulation, and radar data acquisition. Personnel at LaRC are completing the development of the use of supercomputers for mathematical model computation to support real-time flight simulation. This includes the development of a real-time operating system and development of specialized software and hardware for the simulator network. This paper describes the data acquisition technology and the development of supercomputing for flight simulation.

Design and development of an F/A-18 inlet distortion rake: A cost and time saving solution

NASA Technical Reports Server (NTRS)

Yuhas, Andrew J.; Ray, Ronald J.; Burley, Richard R.; Steenken, William G.; Lechtenberg, Leon; Thornton, Don

1995-01-01

An innovative inlet total pressure distortion measurement rake has been designed and developed for the F/A-18 A/B/C/D aircraft inlet. The design was conceived by NASA and General Electric Aircraft Engines personnel. This rake has been flight qualified and flown in the F/A-18 High Alpha Research Vehicle at NASA Dryden Flight Research Center, Edwards, California. The eight-legged, one-piece, wagon wheel design of the rake was developed at a reduced cost and offered reduced installation time compared to traditional designs. The rake features 40 dual-measurement ports for low- and high-frequency pressure measurements with the high-frequency transducer mounted at the port. This high-frequency transducer offers direct absolute pressure measurements from low to high frequencies of interest, thereby allowing the rake to be used during highly dynamic aircraft maneuvers. Outstanding structural characteristics are inherent to the design through its construction and use of lightweight materials.

Optimizing real time fMRI neurofeedback for therapeutic discovery and development

PubMed Central

Stoeckel, L.E.; Garrison, K.A.; Ghosh, S.; Wighton, P.; Hanlon, C.A.; Gilman, J.M.; Greer, S.; Turk-Browne, N.B.; deBettencourt, M.T.; Scheinost, D.; Craddock, C.; Thompson, T.; Calderon, V.; Bauer, C.C.; George, M.; Breiter, H.C.; Whitfield-Gabrieli, S.; Gabrieli, J.D.; LaConte, S.M.; Hirshberg, L.; Brewer, J.A.; Hampson, M.; Van Der Kouwe, A.; Mackey, S.; Evins, A.E.

2014-01-01

While reducing the burden of brain disorders remains a top priority of organizations like the World Health Organization and National Institutes of Health, the development of novel, safe and effective treatments for brain disorders has been slow. In this paper, we describe the state of the science for an emerging technology, real time functional magnetic resonance imaging (rtfMRI) neurofeedback, in clinical neurotherapeutics. We review the scientific potential of rtfMRI and outline research strategies to optimize the development and application of rtfMRI neurofeedback as a next generation therapeutic tool. We propose that rtfMRI can be used to address a broad range of clinical problems by improving our understanding of brain–behavior relationships in order to develop more specific and effective interventions for individuals with brain disorders. We focus on the use of rtfMRI neurofeedback as a clinical neurotherapeutic tool to drive plasticity in brain function, cognition, and behavior. Our overall goal is for rtfMRI to advance personalized assessment and intervention approaches to enhance resilience and reduce morbidity by correcting maladaptive patterns of brain function in those with brain disorders. PMID:25161891

Hot-bench simulation of the active flexible wing wind-tunnel model

NASA Technical Reports Server (NTRS)

Buttrill, Carey S.; Houck, Jacob A.

1990-01-01

Two simulations, one batch and one real-time, of an aeroelastically-scaled wind-tunnel model were developed. The wind-tunnel model was a full-span, free-to-roll model of an advanced fighter concept. The batch simulation was used to generate and verify the real-time simulation and to test candidate control laws prior to implementation. The real-time simulation supported hot-bench testing of a digital controller, which was developed to actively control the elastic deformation of the wind-tunnel model. Time scaling was required for hot-bench testing. The wind-tunnel model, the mathematical models for the simulations, the techniques employed to reduce the hot-bench time-scale factors, and the verification procedures are described.

RT-Syn: A real-time software system generator

NASA Technical Reports Server (NTRS)

Setliff, Dorothy E.

1992-01-01

This paper presents research into providing highly reusable and maintainable components by using automatic software synthesis techniques. This proposal uses domain knowledge combined with automatic software synthesis techniques to engineer large-scale mission-critical real-time software. The hypothesis centers on a software synthesis architecture that specifically incorporates application-specific (in this case real-time) knowledge. This architecture synthesizes complex system software to meet a behavioral specification and external interaction design constraints. Some examples of these external constraints are communication protocols, precisions, timing, and space limitations. The incorporation of application-specific knowledge facilitates the generation of mathematical software metrics which are used to narrow the design space, thereby making software synthesis tractable. Success has the potential to dramatically reduce mission-critical system life-cycle costs not only by reducing development time, but more importantly facilitating maintenance, modifications, and extensions of complex mission-critical software systems, which are currently dominating life cycle costs.

Reducing background contributions in fluorescence fluctuation time-traces for single-molecule measurements in solution.

PubMed

Földes-Papp, Zeno; Liao, Shih-Chu Jeff; You, Tiefeng; Barbieri, Beniamino

2009-08-01

We first report on the development of new microscope means that reduce background contributions in fluorescence fluctuation methods: i) excitation shutter, ii) electronic switches, and iii) early and late time-gating. The elements allow for measuring molecules at low analyte concentrations. We first found conditions of early and late time-gating with time-correlated single-photon counting that made the fluorescence signal as bright as possible compared with the fluctuations in the background count rate in a diffraction-limited optical set-up. We measured about a 140-fold increase in the amplitude of autocorrelated fluorescence fluctuations at the lowest analyte concentration of about 15 pM, which gave a signal-to-background advantage of more than two-orders of magnitude. The results of this original article pave the way for single-molecule detection in solution and in live cells without immobilization or hydrodynamic/electrokinetic focusing at longer observation times than are currently available.

Validation of highly reliable, real-time knowledge-based systems

NASA Technical Reports Server (NTRS)

Johnson, Sally C.

1988-01-01

Knowledge-based systems have the potential to greatly increase the capabilities of future aircraft and spacecraft and to significantly reduce support manpower needed for the space station and other space missions. However, a credible validation methodology must be developed before knowledge-based systems can be used for life- or mission-critical applications. Experience with conventional software has shown that the use of good software engineering techniques and static analysis tools can greatly reduce the time needed for testing and simulation of a system. Since exhaustive testing is infeasible, reliability must be built into the software during the design and implementation phases. Unfortunately, many of the software engineering techniques and tools used for conventional software are of little use in the development of knowledge-based systems. Therefore, research at Langley is focused on developing a set of guidelines, methods, and prototype validation tools for building highly reliable, knowledge-based systems. The use of a comprehensive methodology for building highly reliable, knowledge-based systems should significantly decrease the time needed for testing and simulation. A proven record of delivering reliable systems at the beginning of the highly visible testing and simulation phases is crucial to the acceptance of knowledge-based systems in critical applications.

Develop and pilot test smart phone/tablet app for paratransit demand-response passenger pick-up alerts to assist passengers with disabilities and reduce no-shows and dwell times.

DOT National Transportation Integrated Search

2016-12-01

This research produced an arrival notification system for paratransit passengers with disabilities. Almost all existing curb-to-curb paratransit services have significantly large pick-up time window ranging from 20 to 40 minutes from the scheduled ti...

Profiling the indole alkaloids in yohimbe bark with ultra-performance liquid chromatography coupled with ion mobility quadrupole time-of-flight mass spectrometry

USDA-ARS?s Scientific Manuscript database

An ultra-high performance liquid chromatography-ion mobility- quadrupole time-of-flight mass spectrometry (UHPLC-IM-QTOF-MS) method was developed for profiling the indole alkaloids in yohimbe bark. Many indole alkaloids with the yohimbine core structure, plus methylated, oxidized, and reduced speci...

Developing Stimulus Control of Young Children's Requests to Teachers: Classwide Applications of Multiple Schedules

ERIC Educational Resources Information Center

Cammilleri, Anthony P.; Tiger, Jeffrey H.; Hanley, Gregory P.

2008-01-01

Children may recruit their teachers' attention at undesirably high rates or at inconvenient times. Tiger and Hanley (2004) described a multiple-schedule procedure to reduce ill-timed requests, which involved providing children with two distinct continuous signals that were correlated with periods in which teacher attention was either available or…

Zero energy resonance and the logarithmically slow decay of unstable multilevel systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miyamoto, Manabu

2006-08-15

The long time behavior of the reduced time evolution operator for unstable multilevel systems is studied based on the N-level Friedrichs model in the presence of a zero energy resonance. The latter means the divergence of the resolvent at zero energy. Resorting to the technique developed by Jensen and Kato [Duke Math. J. 46, 583 (1979)], the zero energy resonance of this model is characterized by the zero energy eigenstate that does not belong to the Hilbert space. It is then shown that for some kinds of the rational form factors the logarithmically slow decay proportional to (log t){sup -1}more » of the reduced time evolution operator can be realized.« less

Buffer management for sequential decoding. [block erasure probability reduction

NASA Technical Reports Server (NTRS)

Layland, J. W.

1974-01-01

Sequential decoding has been found to be an efficient means of communicating at low undetected error rates from deep space probes, but erasure or computational overflow remains a significant problem. Erasure of a block occurs when the decoder has not finished decoding that block at the time that it must be output. By drawing upon analogies in computer time sharing, this paper develops a buffer-management strategy which reduces the decoder idle time to a negligible level, and therefore improves the erasure probability of a sequential decoder. For a decoder with a speed advantage of ten and a buffer size of ten blocks, operating at an erasure rate of .01, use of this buffer-management strategy reduces the erasure rate to less than .0001.

Job-shop scheduling applied to computer vision

NASA Astrophysics Data System (ADS)

Sebastian y Zuniga, Jose M.; Torres-Medina, Fernando; Aracil, Rafael; Reinoso, Oscar; Jimenez, Luis M.; Garcia, David

1997-09-01

This paper presents a method for minimizing the total elapsed time spent by n tasks running on m differents processors working in parallel. The developed algorithm not only minimizes the total elapsed time but also reduces the idle time and waiting time of in-process tasks. This condition is very important in some applications of computer vision in which the time to finish the total process is particularly critical -- quality control in industrial inspection, real- time computer vision, guided robots. The scheduling algorithm is based on the use of two matrices, obtained from the precedence relationships between tasks, and the data obtained from the two matrices. The developed scheduling algorithm has been tested in one application of quality control using computer vision. The results obtained have been satisfactory in the application of different image processing algorithms.

Effect of gum chewing on reducing postoperative ileus and recovery after colorectal surgery: A randomised controlled trial.

PubMed

Topcu, Sacide Yildizeli; Oztekin, Seher Deniz

2016-05-01

This study aimed to determine the effect of gum chewing on the reduction of postoperative ileus and recovery after surgery. This study was conducted a randomized controlled trial in 60 patients who underwent colorectal surgery between November 2011 and December 2012. Patients in the experimental group chewed gum three times a day. The time of flatus and defecation, the time to start feeding, pain levels and time of discharge were monitored. Post-surgery results for gum-chewing were first flatus and defecation times and the time to start feeding was shorter; pain levels were lower on the 3rd - 5th days; patients were discharged in a shorter time post-surgery. Chewing gum is a simple intervention for reducing postoperative ileus after colorectal surgery. Further studies that examine the effectiveness of gum chewing on other surgical interventions in which the development risk of postoperative ileus should be performed. Copyright © 2016 Elsevier Ltd. All rights reserved.

Progress Toward National Aeronautics Goals

NASA Technical Reports Server (NTRS)

Russo, Carlo J.; Sehra, Arun K.

1999-01-01

NASA has made definitive progress towards achieving several bold U.S. goals in aeronautics related to air breathing engines. The advanced technologies developed towards these goals span applications from general aviation to large subsonic and supersonic aircraft. The proof of successful technology development is demonstrated through successful technology transfer to U.S. industry and projected fleet impact. Specific examples of progress are discussed that quantifies the achievement towards these goals. In addition, a more detailed vision for NASA aeronautics is defined and key strategic issues are explored which invite international and national debate and involvement especially in reduced environmental impact for subsonic and supersonic aircraft, dramatic new capabilities in general aviation engines, and reduced development cycle time and costs.

Noise reduction with complex bilateral filter.

PubMed

Matsumoto, Mitsuharu

2017-12-01

This study introduces a noise reduction technique that uses a complex bilateral filter. A bilateral filter is a nonlinear filter originally developed for images that can reduce noise while preserving edge information. It is an attractive filter and has been used in many applications in image processing. When it is applied to an acoustical signal, small-amplitude noise is reduced while the speech signal is preserved. However, a bilateral filter cannot handle noise with relatively large amplitudes owing to its innate characteristics. In this study, the noisy signal is transformed into the time-frequency domain and the filter is improved to handle complex spectra. The high-amplitude noise is reduced in the time-frequency domain via the proposed filter. The features and the potential of the proposed filter are also confirmed through experiments.

Advanced rocket propulsion

NASA Technical Reports Server (NTRS)

Obrien, Charles J.

1993-01-01

Existing NASA research contracts are supporting development of advanced reinforced polymer and metal matrix composites for use in liquid rocket engines of the future. Advanced rocket propulsion concepts, such as modular platelet engines, dual-fuel dual-expander engines, and variable mixture ratio engines, require advanced materials and structures to reduce overall vehicle weight as well as address specific propulsion system problems related to elevated operating temperatures, new engine components, and unique operating processes. High performance propulsion systems with improved manufacturability and maintainability are needed for single stage to orbit vehicles and other high performance mission applications. One way to satisfy these needs is to develop a small engine which can be clustered in modules to provide required levels of total thrust. This approach should reduce development schedule and cost requirements by lowering hardware lead times and permitting the use of existing test facilities. Modular engines should also reduce operational costs associated with maintenance and parts inventories.

Reducing beam shaper alignment complexity: diagnostic techniques for alignment and tuning

NASA Astrophysics Data System (ADS)

Lizotte, Todd E.

2011-10-01

Safe and efficient optical alignment is a critical requirement for industrial laser systems used in a high volume manufacturing environment. Of specific interest is the development of techniques to align beam shaping optics within a beam line; having the ability to instantly verify by a qualitative means that each element is in its proper position as the beam shaper module is being aligned. There is a need to reduce these types of alignment techniques down to a level where even a newbie to optical alignment will be able to complete the task. Couple this alignment need with the fact that most laser system manufacturers ship their products worldwide and the introduction of a new set of variables including cultural and language barriers, makes this a top priority for manufacturers. Tools and methodologies for alignment of complex optical systems need to be able to cross these barriers to ensure the highest degree of up time and reduce the cost of maintenance on the production floor. Customers worldwide, who purchase production laser equipment, understand that the majority of costs to a manufacturing facility is spent on system maintenance and is typically the largest single controllable expenditure in a production plant. This desire to reduce costs is driving the trend these days towards predictive and proactive, not reactive maintenance of laser based optical beam delivery systems [10]. With proper diagnostic tools, laser system developers can develop proactive approaches to reduce system down time, safe guard operational performance and reduce premature or catastrophic optics failures. Obviously analytical data will provide quantifiable performance standards which are more precise than qualitative standards, but each have a role in determining overall optical system performance [10]. This paper will discuss the use of film and fluorescent mirror devices as diagnostic tools for beam shaper module alignment off line or in-situ. The paper will also provide an overview methodology showing how it is possible to reduce complex alignment directions into a simplified set of instructions for layman service engineers.

Development of black soldier fly (Diptera: Stratiomyidae) larvae fed dairy manure.

PubMed

Myers, Heidi M; Tomberlin, Jeffery K; Lambert, Barry D; Kattes, David

2008-02-01

Black soldier flies, Hermetia illucens L., are a common colonizer of animal wastes. However, all published development data for this species are from studies using artificial diets. This study represents the first examining black soldier fly development on animal wastes. Additionally, this study examined the ability of black soldier fly larvae to reduce dry matter and associated nutrients in manure. Black soldier fly larvae were fed four rates of dairy manure to determine their effects on larval and adult life history traits. Feed rate affected larval and adult development. Those fed less ration daily weighed less than those fed a greater ration. Additionally, larvae provided the least amount of dairy manure took longer to develop to the prepupal stage; however, they needed less time to reach the adult stage. Adults resulting from larvae provided 27 g dairy manure/d lived 3-4 d less than those fed 70 g dairy manure. Percentage survivorship to the prepupal or adult stages did not differ across treatments. Larvae fed 27 g dairy manure daily reduced manure dry matter mass by 58%, whereas those fed 70 g daily reduced dry matter 33%. Black soldier fly larvae were able to reduce available P by 61-70% and N by 30-50% across treatments. Based on results from this study, the black soldier fly could be used to reduce wastes and associated nutrients in confined bovine facilities.

Reducing maternal mortality: can we derive policy guidance from developing country experiences?

PubMed

Liljestrand, Jerker; Pathmanathan, Indra

2004-01-01

Developing countries are floundering in their efforts to meet the Millennium Development Goal of reducing maternal mortality by 75% by 2015. Two issues are being debated. Is it doable within this time frame? And is it affordable? Malaysia and Sri Lanka have in the past 50 years repeatedly halved their maternal mortality ratio (MMR) every 7-10 years to reduce MMR from over 500 to below 50. Experience from four other developing countries--Bolivia, Yunan in China, Egypt, and Jamaica-confirms that each was able to halve MMR in less than 10 years beginning from levels of 200-300. Malaysia and Sri Lanka, invested modestly (but wisely)--less than 0.4% of GDP--on maternal health throughout the period of decline, although the large majority of women depended on publicly funded maternal health care. Analysis of their experience suggests that provision of access to and removal of barriers for the use of skilled birth attendance has been the key. This included professionalization of midwifery and phasing out of traditional birth attendants; monitoring births and maternal deaths and use of such information for high profile advocacy on the importance of reducing maternal death; and addressing critical gaps in the health system; and reducing disparities between different groups through special attention to the poor and disadvantaged populations.

Optimal placement of tuning masses for vibration reduction in helicopter rotor blades

NASA Technical Reports Server (NTRS)

Pritchard, Jocelyn I.; Adelman, Howard M.

1988-01-01

Described are methods for reducing vibration in helicopter rotor blades by determining optimum sizes and locations of tuning masses through formal mathematical optimization techniques. An optimization procedure is developed which employs the tuning masses and corresponding locations as design variables which are systematically changed to achieve low values of shear without a large mass penalty. The finite-element structural analysis of the blade and the optimization formulation require development of discretized expressions for two performance parameters: modal shaping parameter and modal shear amplitude. Matrix expressions for both quantities and their sensitivity derivatives are developed. Three optimization strategies are developed and tested. The first is based on minimizing the modal shaping parameter which indirectly reduces the modal shear amplitudes corresponding to each harmonic of airload. The second strategy reduces these amplitudes directly, and the third strategy reduces the shear as a function of time during a revolution of the blade. The first strategy works well for reducing the shear for one mode responding to a single harmonic of the airload, but has been found in some cases to be ineffective for more than one mode. The second and third strategies give similar results and show excellent reduction of the shear with a low mass penalty.

Innovative Product Development Partnership Reduced Neonatal Mortality In Nepal Through Improved Umbilical Cord Care.

PubMed

Oyloe, Peter; Khanal, Leela; Hodgins, Stephen; Pradhan, Sabita T; Dawson, Penny

2017-11-01

Approximately 40 percent of all newborn deaths in Nepal are attributable to neonatal infections. A randomized controlled trial conducted in Nepal in the period 2002-05 on the application of a solution of the disinfectant chlorhexidine to umbilical cord stumps of newborns showed a reduced risk of infections and death. In response to these results, the Government of Nepal and various partners mobilized to deliver this simple, low-cost intervention on a national scale. We describe the design, development, and maturation of a partnership among the government, technical assistance agencies, and a local pharmaceutical company to create a suitable, commercially available gel product to reduce newborn infections. Essential contributors to the partnership's effectiveness included having a for-profit pharmaceutical company as a fully engaged partner; having responsive, flexible relationships among the partners that evolved over time; and paying attention to competition within the private sector. A less formalized arrangement among partners allowed them to build trust in each other over time. Government stewardship of the program throughout the scale-up process ensured that policy and systems integration were aligned as the program matured.

Space-based Networking Technology Developments in the Interplanetary Network Directorate Information Technology Program

NASA Technical Reports Server (NTRS)

Clare, Loren; Clement, B.; Gao, J.; Hutcherson, J.; Jennings, E.

2006-01-01

Described recent development of communications protocols, services, and associated tools targeted to reduce risk, reduce cost and increase efficiency of IND infrastructure and supported mission operations. Space-based networking technologies developed were: a) Provide differentiated quality of service (QoS) that will give precedence to traffic that users have selected as having the greatest importance and/or time-criticality; b) Improve the total value of information to users through the use of QoS prioritization techniques; c) Increase operational flexibility and improve command-response turnaround; d) Enable new class of networked and collaborative science missions; e) Simplify applications interfaces to communications services; and f) Reduce risk and cost from a common object model and automated scheduling and communications protocols. Technologies are described in three general areas: communications scheduling, middleware, and protocols. Additionally developed simulation environment, which provides comprehensive, quantitative understanding of the technologies performance within overall, evolving architecture, as well as ability to refine & optimize specific components.

Gathering time-series data for evaluating behavior-change campaigns in developing countries: reactivity of diaries and interviews.

PubMed

Tobias, Robert; Inauen, Jennifer

2010-10-01

Gathering time-series data of behaviors and psychological variables is important to understand, guide, and evaluate behavior-change campaigns and other change processes. However, repeated measurement can affect the phenomena investigated, particularly frequent face-to-face interviews, which are often the only option in developing countries. This article presents three intervention control studies to investigate this issue. Daily diaries in Cuba did not affect behavior or attitudes for persons with intervention but reduced attitudes for persons without intervention. Reactivity of face-to-face interviews in Bolivia was negligible if applied weekly, but strong if applied twice per week. The article concludes with recommendations for gathering time-series data in developing countries.

Reduced and Validated Kinetic Mechanisms for Hydrogen-CO-sir Combustion in Gas Turbines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yiguang Ju; Frederick Dryer

2009-02-07

Rigorous experimental, theoretical, and numerical investigation of various issues relevant to the development of reduced, validated kinetic mechanisms for synthetic gas combustion in gas turbines was carried out - including the construction of new radiation models for combusting flows, improvement of flame speed measurement techniques, measurements and chemical kinetic analysis of H{sub 2}/CO/CO{sub 2}/O{sub 2}/diluent mixtures, revision of the H{sub 2}/O{sub 2} kinetic model to improve flame speed prediction capabilities, and development of a multi-time scale algorithm to improve computational efficiency in reacting flow simulations.

Student-oriented learning outlines: a valuable supplement to traditional instruction.

PubMed

VanArsdale, S K; Hammons, J O

1998-01-01

In a time of changing health care and funding restraints in institutions, continuing education and staff development departments are being challenged to produce better prepared nurses at reduced costs per employee. Improvements in how nurses are prepared are needed to ensure higher levels of competence without increasing the cost. This article describes the development and use of a practical strategy for mastery learning known as Student-Oriented Learning Outlines or SOLOs. This approach has been found to be effective in producing improvements in learning and ultimately patient care while reducing cost to the institution.

Floating-Point Modules Targeted for Use with RC Compilation Tools

NASA Technical Reports Server (NTRS)

Sahin, Ibrahin; Gloster, Clay S.

2000-01-01

Reconfigurable Computing (RC) has emerged as a viable computing solution for computationally intensive applications. Several applications have been mapped to RC system and in most cases, they provided the smallest published execution time. Although RC systems offer significant performance advantages over general-purpose processors, they require more application development time than general-purpose processors. This increased development time of RC systems provides the motivation to develop an optimized module library with an assembly language instruction format interface for use with future RC system that will reduce development time significantly. In this paper, we present area/performance metrics for several different types of floating point (FP) modules that can be utilized to develop complex FP applications. These modules are highly pipelined and optimized for both speed and area. Using these modules, and example application, FP matrix multiplication, is also presented. Our results and experiences show, that with these modules, 8-10X speedup over general-purpose processors can be achieved.

Laser Balancing

NASA Technical Reports Server (NTRS)

1981-01-01

Mechanical Technology, Incorporated developed a fully automatic laser machining process that allows more precise balancing removes metal faster, eliminates excess metal removal and other operator induced inaccuracies, and provides significant reduction in balancing time. Manufacturing costs are reduced as a result.

Automated Tendering and Purchasing.

ERIC Educational Resources Information Center

DeZorzi, James M.

1980-01-01

The Middlesex County Board of Education in Hyde Park (Ontario) has developed an automated tendering/purchasing system for ordering standard items that has reduced by 80 percent the time required for tendering, evaluating, awarding, and ordering items. (Author/MLF)

Microwave-assisted synthesis of organics and nanomaterials

EPA Science Inventory

Microwave-assisted chemistry techniques and greener reaction media are dramatically reducing chemical waste and reaction times in several organic transformations and material synthesis. This presentation summarizes author’s own experience in developing MW-assisted chemical proces...

Deductive Glue Code Synthesis for Embedded Software Systems Based on Code Patterns

NASA Technical Reports Server (NTRS)

Liu, Jian; Fu, Jicheng; Zhang, Yansheng; Bastani, Farokh; Yen, I-Ling; Tai, Ann; Chau, Savio N.

2006-01-01

Automated code synthesis is a constructive process that can be used to generate programs from specifications. It can, thus, greatly reduce the software development cost and time. The use of formal code synthesis approach for software generation further increases the dependability of the system. Though code synthesis has many potential benefits, the synthesis techniques are still limited. Meanwhile, components are widely used in embedded system development. Applying code synthesis to component based software development (CBSD) process can greatly enhance the capability of code synthesis while reducing the component composition efforts. In this paper, we discuss the issues and techniques for applying deductive code synthesis techniques to CBSD. For deductive synthesis in CBSD, a rule base is the key for inferring appropriate component composition. We use the code patterns to guide the development of rules. Code patterns have been proposed to capture the typical usages of the components. Several general composition operations have been identified to facilitate systematic composition. We present the technique for rule development and automated generation of new patterns from existing code patterns. A case study of using this method in building a real-time control system is also presented.

Peering into the secrets of food and agricultural co-products

NASA Astrophysics Data System (ADS)

Wood, Delilah; Williams, Tina; Glenn, Gregory; Pan, Zhongli; Orts, William; McHugh, Tara

2010-06-01

Scanning electron microscopy is a useful tool for understanding food contamination and directing product development of food and industrial products. The current trend in food research is to produce foods that are fast to prepare and/or ready to eat. At the same time, these processed foods must be safe, high quality and maintain all or most of the nutritional value of the original whole foods. Minimally processed foods, is the phrase used to characterize these "new" foods. New techniques are needed which take advantage of minimal processing or processing which enhances the fresh properties and characteristics of whole foods while spending less time on food preparation. The added benefit coupled to less cooking time in an individual kitchen translates to an overall energy savings and reduces the carbon emissions to the environment. Food processing changes the microstructure, and therefore, the quality, texture and flavor, of the resulting food product. Additionally, there is the need to reduce waste, transportation costs and product loss during transportation and storage. Unlike food processing, structural changes are desirable in co-products as function follows form for food packaging films and boxes as well as for building materials and other industrial products. Thus, the standard materials testing procedures are coupled with SEM to provide direction in the development of products from agricultural residues or what would otherwise be considered waste materials. The use of agricultural residues reduces waste and adds value to a currently underutilized or unutilized product. The product might be biodegradable or compostable, thus reducing landfill requirements. Manufacturing industrial and packaging products from biological materials also reduces the amount of petroleum products currently standard in the industry.

Reduced cost and improved figure of sapphire optical components

NASA Astrophysics Data System (ADS)

Walters, Mark; Bartlett, Kevin; Brophy, Matthew R.; DeGroote Nelson, Jessica; Medicus, Kate

2015-10-01

Sapphire presents many challenges to optical manufacturers due to its high hardness and anisotropic properties. Long lead times and high prices are the typical result of such challenges. The cost of even a simple 'grind and shine' process can be prohibitive. The high precision surfaces required by optical sensor applications further exacerbate the challenge of processing sapphire thereby increasing cost further. Optimax has demonstrated a production process for such windows that delivers over 50% time reduction as compared to traditional manufacturing processes for sapphire, while producing windows with less than 1/5 wave rms figure error. Optimax's sapphire production process achieves significant improvement in cost by implementation of a controlled grinding process to present the best possible surface to the polishing equipment. Following the grinding process is a polishing process taking advantage of chemical interactions between slurry and substrate to deliver excellent removal rates and surface finish. Through experiments, the mechanics of the polishing process were also optimized to produce excellent optical figure. In addition to reducing the cost of producing large sapphire sensor windows, the grinding and polishing technology Optimax has developed aids in producing spherical sapphire components to better figure quality. In addition to reducing the cost of producing large sapphire sensor windows, the grinding and polishing technology Optimax has developed aids in producing spherical sapphire components to better figure quality. Through specially developed polishing slurries, the peak-to-valley figure error of spherical sapphire parts is reduced by over 80%.

Developing a Performance Data Suite to Facilitate Lean Improvement in a Chemotherapy Day Unit

PubMed Central

Lingaratnam, Senthil; Murray, Danielle; Carle, Amber; Kirsa, Sue W.; Paterson, Rebecca; Rischin, Danny

2013-01-01

Purpose: A multidisciplinary team from the Peter MacCallum Cancer Centre in Melbourne, Australia, developed a performance data suite to support a service improvement project based on lean manufacturing principles in its 19-chair chemotherapy day unit (CDU) and cytosuite chemotherapy production facility. The aims of the project were to reduce patient wait time and improve equity of access to the CDU. Methods: A project team consisting of a pharmacist and CDU nurse supported the management team for 10 months in engaging staff and customers to identify waste in processes, analyze root causes, eliminate non–value-adding steps, reduce variation, and level workloads to improve quality and flow. Process mapping, staff and patient tracking and opinion surveys, medical record audits, and interrogation of electronic treatment records were undertaken. Results: This project delivered a 38% reduction in median wait time on the day (from 32 to 20 minutes; P < .01), 7-day reduction in time to commencement of treatment for patients receiving combined chemoradiotherapy regimens (from 25 to 18 days; P < .01), and 22% reduction in wastage associated with expired drug and pharmacy rework (from 29% to 7%; P < .01). Improvements in efficiency enabled the cytosuite to increase the percentage of product manufactured within 10 minutes of appointment times by 29% (from 47% to 76%; P < .01). Conclusion: A lean improvement methodology provided a robust framework for improved understanding and management of complex system constraints within a CDU, resulting in improved access to treatment and reduced waiting times on the day. PMID:23942927

Time-saving impact of an algorithm to identify potential surgical site infections.

PubMed

Knepper, B C; Young, H; Jenkins, T C; Price, C S

2013-10-01

To develop and validate a partially automated algorithm to identify surgical site infections (SSIs) using commonly available electronic data to reduce manual chart review. Retrospective cohort study of patients undergoing specific surgical procedures over a 4-year period from 2007 through 2010 (algorithm development cohort) or over a 3-month period from January 2011 through March 2011 (algorithm validation cohort). A single academic safety-net hospital in a major metropolitan area. Patients undergoing at least 1 included surgical procedure during the study period. Procedures were identified in the National Healthcare Safety Network; SSIs were identified by manual chart review. Commonly available electronic data, including microbiologic, laboratory, and administrative data, were identified via a clinical data warehouse. Algorithms using combinations of these electronic variables were constructed and assessed for their ability to identify SSIs and reduce chart review. The most efficient algorithm identified in the development cohort combined microbiologic data with postoperative procedure and diagnosis codes. This algorithm resulted in 100% sensitivity and 85% specificity. Time savings from the algorithm was almost 600 person-hours of chart review. The algorithm demonstrated similar sensitivity on application to the validation cohort. A partially automated algorithm to identify potential SSIs was highly sensitive and dramatically reduced the amount of manual chart review required of infection control personnel during SSI surveillance.

Reduced endothelin converting enzyme-1 and endothelin-3 mRNA in the developing bowel of male mice may increase expressivity and penetrance of Hirschsprung disease-like distal intestinal aganglionosis.

PubMed

Vohra, Bhupinder P S; Planer, William; Armon, Jennifer; Fu, Ming; Jain, Sanjay; Heuckeroth, Robert O

2007-01-01

Hirschsprung disease (distal intestinal aganglionosis, HSCR) is a multigenic disorder with incomplete penetrance, variable expressivity, and a strong male gender bias. Recent studies demonstrated that these genetic patterns arise because gene interactions determine whether enteric nervous system (ENS) precursors successfully proliferate and migrate into the distal bowel. We now demonstrate that male gender bias in the extent of distal intestinal aganglionosis occurs in mice with Ret dominant-negative mutations (RetDN) that mimic human HSCR. We hypothesized that male gender bias could result from reduced expression of a gene already known to be essential for ENS development. Using quantitative real-time polymerase chain reaction (PCR) we demonstrated reduced levels of endothelin converting enzyme-1 and endothelin-3 mRNA in the male mouse bowel at the time that ENS precursors migrate into the colon. Other HSCR-associated genes are expressed at comparable levels in male and female mice. Testosterone and Mullerian inhibiting substance had no deleterious effect on ENS precursor development, but adding EDN3 peptide to E11.5 male RetDN heterozygous mouse gut explants in organ culture significantly increased the rate of ENS precursor migration through the bowel.

A Controlled Agitation Process for Improving Quality of Canned Green Beans during Agitation Thermal Processing.

PubMed

Singh, Anika; Pratap Singh, Anubhav; Ramaswamy, Hosahalli S

2016-06-01

This work introduces the concept of a controlled agitation thermal process to reduce quality damage in liquid-particulate products during agitation thermal processing. Reciprocating agitation thermal processing (RA-TP) was used as the agitation thermal process. In order to reduce the impact of agitation, a new concept of "stopping agitations after sufficient development of cold-spot temperature" was proposed. Green beans were processed in No. 2 (307×409) cans filled with liquids of various consistency (0% to 2% CMC) at various frequencies (1 to 3 Hz) of RA-TP using a full-factorial design and heat penetration results were collected. Corresponding operator's process time to impart a 10-min process lethality (Fo ) and agitation time (AT) were calculated using heat penetration results. Accordingly, products were processed again by stopping agitations as per 3 agitation regimes, namely; full time agitation, equilibration time agitation, and partial time agitation. Processed products were photographed and tested for visual quality, color, texture, breakage of green beans, turbidity, and percentage of insoluble solids in can liquid. Results showed that stopping agitations after sufficient development of cold-spot temperatures is an effective way of reducing product damages caused by agitation (for example, breakage of beans and its leaching into liquid). Agitations till one-log temperature difference gave best color, texture and visual product quality for low-viscosity liquid-particulate mixture and extended agitations till equilibration time was best for high-viscosity products. Thus, it was shown that a controlled agitation thermal process is more effective in obtaining high product quality as compared to a regular agitation thermal process. © 2016 Institute of Food Technologists®

Using time management to achieve balance.

PubMed

Schroeder, R E

1998-01-01

A recent MGMA survey showed work-life balance as the number one issue facing group practice managers. This article explains techniques from the field of time management that will enable group practice managers to gain control of their schedules, reduce time pressures and stress and increase productivity. The article covers: goal setting, daily lists, handling paperwork, delegating and limiting involvement, socializing, communicating, overachieving, planning, writing, telephone calling, attending meetings, reading, financial planning, developing a philosophy, involving family, evaluating skills and teaching time management to employees.

TES: A modular systems approach to expert system development for real-time space applications

NASA Technical Reports Server (NTRS)

Cacace, Ralph; England, Brenda

1988-01-01

A major goal of the Space Station era is to reduce reliance on support from ground based experts. The development of software programs using expert systems technology is one means of reaching this goal without requiring crew members to become intimately familiar with the many complex spacecraft subsystems. Development of an expert systems program requires a validation of the software with actual flight hardware. By combining accurate hardware and software modelling techniques with a modular systems approach to expert systems development, the validation of these software programs can be successfully completed with minimum risk and effort. The TIMES Expert System (TES) is an application that monitors and evaluates real time data to perform fault detection and fault isolation tasks as they would otherwise be carried out by a knowledgeable designer. The development process and primary features of TES, a modular systems approach, and the lessons learned are discussed.

Software Certification and Software Certificate Management Systems

NASA Technical Reports Server (NTRS)

Denney, Ewen; Fischer, Bernd

2005-01-01

Incremental certification and re-certification of code as it is developed and modified is a prerequisite for applying modem, evolutionary development processes, which are especially relevant for NASA. For example, the Columbia Accident Investigation Board (CAIB) report 121 concluded there is "the need for improved and uniform statistical sampling, audit, and certification processes". Also, re-certification time has been a limiting factor in making changes to Space Shuttle code close to launch time. This is likely to be an even bigger problem with the rapid turnaround required in developing NASA s replacement for the Space Shuttle, the Crew Exploration Vehicle (CEV). Hence, intelligent development processes are needed which place certification at the center of development. If certification tools provide useful information, such as estimated time and effort, they are more likely to be adopted. The ultimate impact of such a tool will be reduced effort and increased reliability.

Use of Six Sigma Methodology to Reduce Appointment Lead-Time in Obstetrics Outpatient Department.

PubMed

Ortiz Barrios, Miguel A; Felizzola Jiménez, Heriberto

2016-10-01

This paper focuses on the issue of longer appointment lead-time in the obstetrics outpatient department of a maternal-child hospital in Colombia. Because of extended appointment lead-time, women with high-risk pregnancy could develop severe complications in their health status and put their babies at risk. This problem was detected through a project selection process explained in this article and to solve it, Six Sigma methodology has been used. First, the process was defined through a SIPOC diagram to identify its input and output variables. Second, six sigma performance indicators were calculated to establish the process baseline. Then, a fishbone diagram was used to determine the possible causes of the problem. These causes were validated with the aid of correlation analysis and other statistical tools. Later, improvement strategies were designed to reduce appointment lead-time in this department. Project results evidenced that average appointment lead-time reduced from 6,89 days to 4,08 days and the deviation standard dropped from 1,57 days to 1,24 days. In this way, the hospital will serve pregnant women faster, which represents a risk reduction of perinatal and maternal mortality.

How Pronounced Is Income Inequality around the World--and How Can Education Help Reduce It? Education Indicators in Focus. No. 4

ERIC Educational Resources Information Center

OECD Publishing (NJ1), 2012

2012-01-01

How pronounced is income inequality around the world--and how can education help reduce it? This paper reports the following: (1) Across OECD (Organisation for Economic Cooperation and Development) countries, the average income of the richest 10% of the population was about nine times that of the poorest 10% before the onset of the global economic…

Biotechnology Research Requirements for Aeronautical Systems through the Year 2000. Volume 1

DTIC Science & Technology

1982-07-30

signature. Reducing the aero contain radic.?z,:"ve fallout. vehicle’s detectibility by reducing the optical, electro, acoustic, and infrared 0 Pulsed...arsenal devoted to agent doses. At this time, basic biochemical and chemical agents, reported use of mycotoxins and pharmacological data are minimal and...mass spectroscopy , quartz chemical agents must be developed. This research microbalances, Industrial hygiene dosimetry, damp should quantify human

An Analysis Of Personalized Learning Systems For Navy Training And Education Settings

DTIC Science & Technology

2016-12-01

of dedicated “schoolhouse” training and education among the services account for approximately $8.7 billion per year (Department of Defense [DOD...calls it customized learning) opportunities for the Air Force with the sole intent of reducing time-to- train , and thereby significantly reducing...technology to develop and distribute personalized, cost-effective, always available, high quality training and education to service members and DOD

Reduction of Energy Intake using Just-In-Time Feedback from a Wearable Sensor System

PubMed Central

Farooq, Muhammad; McCrory, Megan A.; Sazonov, Edward

2017-01-01

Objective This work explored the potential use of a wearable sensor system for providing just-in-time (JIT) feedback on the progression of a meal and tested its ability to reduce the total food mass intake. Methods Eighteen participants each consumed three meals in a lab while monitored by a wearable sensor system capable of accurately tracking chew counts. The baseline visit was used to establish the self-determined ingested mass and the associated chew counts. Real-time feedback on chew counts was provided in the next two visits during which the target chew counts was either the same as that at baseline or the baseline chew counts reduced by 25%, in randomized order. The target was concealed from the participant and from the experimenter. Nonparametric repeated-measures ANOVA were performed to compare mass of intake, meal duration, and ratings of hunger, appetite, and thirst across 3 meals. Results JIT feedback targeting a 25% reduction in chew counts resulted in a reduction in mass and energy intake without affecting perceived hunger or fullness. Conclusion JIT feedback on chewing behavior may reduce intake within a meal. This system can be further used to help develop individualized strategies to provide just-in-time adaptive interventions for reducing energy intake. PMID:28233942

Software Development Technologies for Reactive, Real-Time, and Hybrid Systems

NASA Technical Reports Server (NTRS)

Manna, Zohar

1996-01-01

The research is directed towards the design and implementation of a comprehensive deductive environment for the development of high-assurance systems, especially reactive (concurrent, real-time, and hybrid) systems. Reactive systems maintain an ongoing interaction with their environment, and are among the most difficult to design and verify. The project aims to provide engineers with a wide variety of tools within a single, general, formal framework in which the tools will be most effective. The entire development process is considered, including the construction, transformation, validation, verification, debugging, and maintenance of computer systems. The goal is to automate the process as much as possible and reduce the errors that pervade hardware and software development.

Implementation of unsteady sampling procedures for the parallel direct simulation Monte Carlo method

NASA Astrophysics Data System (ADS)

Cave, H. M.; Tseng, K.-C.; Wu, J.-S.; Jermy, M. C.; Huang, J.-C.; Krumdieck, S. P.

2008-06-01

An unsteady sampling routine for a general parallel direct simulation Monte Carlo method called PDSC is introduced, allowing the simulation of time-dependent flow problems in the near continuum range. A post-processing procedure called DSMC rapid ensemble averaging method (DREAM) is developed to improve the statistical scatter in the results while minimising both memory and simulation time. This method builds an ensemble average of repeated runs over small number of sampling intervals prior to the sampling point of interest by restarting the flow using either a Maxwellian distribution based on macroscopic properties for near equilibrium flows (DREAM-I) or output instantaneous particle data obtained by the original unsteady sampling of PDSC for strongly non-equilibrium flows (DREAM-II). The method is validated by simulating shock tube flow and the development of simple Couette flow. Unsteady PDSC is found to accurately predict the flow field in both cases with significantly reduced run-times over single processor code and DREAM greatly reduces the statistical scatter in the results while maintaining accurate particle velocity distributions. Simulations are then conducted of two applications involving the interaction of shocks over wedges. The results of these simulations are compared to experimental data and simulations from the literature where there these are available. In general, it was found that 10 ensembled runs of DREAM processing could reduce the statistical uncertainty in the raw PDSC data by 2.5-3.3 times, based on the limited number of cases in the present study.

Laboratory automation —some perspectives on the challenges in the implementation of the technology in pharmaceutical development

PubMed Central

North, Nigel; Smith, Simon

1998-01-01

The intensifying pressure on reducing the development time for new pharmaceutical products is resulting in an increasing need for laboratory automation. A key element for the successful implementation of robotics for drug product analysis is the establishment of a reliable process for interaction of the automation team with its various customers, for example development product team and manufacturing group. The reduction of cycle time for product development appears to be resulting in more stability studies to support NDA/MAA filings for several reasons. Key clinical information may not be available before initiation of the stability studies and simultaneous world-wide development may result in an increase in the number of product strength and pack options. PMID:18924828

Advanced Combustion Numerics and Modeling - FY18 First Quarter Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Whitesides, R. A.; Killingsworth, N. J.; McNenly, M. J.

This project is focused on early stage research and development of numerical methods and models to improve advanced engine combustion concepts and systems. The current focus is on development of new mathematics and algorithms to reduce the time to solution for advanced combustion engine design using detailed fuel chemistry. The research is prioritized towards the most time-consuming workflow bottlenecks (computer and human) and accuracy gaps that slow ACS program members. Zero-RK, the fast and accurate chemical kinetics solver software developed in this project, is central to the research efforts and continues to be developed to address the current and emergingmore » needs of the engine designers, engine modelers and fuel mechanism developers.« less

Etiological study of the short needle disease of pine

Treesearch

Francis A. Wood; Stanley P. Pennypacker

1976-01-01

The short needle disease of pines consists of dwarfing, crooking, twisting, and excessive elongation of random needles, failure of buds to develop, reduced lateral branch development and the premature casting of needles. The disease was initially associated with a power plant source of air pollution in the eastern United States during 1969; at that time the cause of...

Computer-Managed Instruction: Development and Evaluation of Student Skill Modules to Reduce Training Time.

ERIC Educational Resources Information Center

McCombs, Barbara L.; And Others

The Computer Managed Instruction (CMI) Student Skills Project was developed and evaluated within the context of the Air Force Advanced Instructional System (AIS), with student study skill modules designed as short packages to be assigned near the beginning of any military technical training course; strategies or procedures included were expected…

The Effect of Bullying and Victimization on Cognitive Empathy Development during the Transition to Middle School

ERIC Educational Resources Information Center

Williford, Anne; Boulton, Aaron J.; Forrest-Bank, Shandra S.; Bender, Kimberly A.; Dieterich, William A.; Jenson, Jeffrey M.

2016-01-01

Background: Interventions aimed at reducing bullying behavior commonly target the development of empathy. Yet, few longitudinal studies have investigated how empathy levels vary with bullying and victimization over time, especially during the transition to middle school. Objective: To that end, the purpose of the present study was to: (1) examine…

More than Poverty: Pathways from Economic Inequality to Reduced Developmental Potential

ERIC Educational Resources Information Center

Wachs, Theodore D.; Cueto, Santiago; Yao, Haogen

2016-01-01

Studies from both high and low-middle income (LAMI) countries have documented how being reared in poverty is linked to compromised child development. Links between poverty and development are mediated by the timing and extent of exposure to both risk factors nested under poverty and to protective influences which can attenuate the impact of risk.…

A Study of the Relationship between Professional Development Evaluation and Middle School Mathematics Achievement

ERIC Educational Resources Information Center

Agnant Rogers, Myriam

2013-01-01

As a result of poor student performance, professional development has emerged as a key strategy for improving instruction and achievement. In times of reduced resources and increased accountability, schools must evaluate their efforts in order to make sound decisions about policy and practice. This mixed method study was designed to investigate…

Alternative Work Arrangements among Professionals and Managers: Rethinking Career Development and Success.

ERIC Educational Resources Information Center

MacDermid, Shelley M.; Lee, Mary Dean; Buck, Michelle; Williams, Margaret L.

2001-01-01

A study of 78 women professionals/managers working reduced hours for family or personal reasons showed that less successful arrangements were associated with lack of upward mobility, underemployment, pressure to work full time, and difficult relations with co-workers. Career development was a concern for those in both more and less successful…

Peak-Seeking Control For Reduced Fuel Consumption: Flight-Test Results For The Full-Scale Advanced Systems Testbed FA-18 Airplane

NASA Technical Reports Server (NTRS)

Brown, Nelson

2013-01-01

A peak-seeking control algorithm for real-time trim optimization for reduced fuel consumption has been developed by researchers at the National Aeronautics and Space Administration (NASA) Dryden Flight Research Center to address the goals of the NASA Environmentally Responsible Aviation project to reduce fuel burn and emissions. The peak-seeking control algorithm is based on a steepest-descent algorithm using a time-varying Kalman filter to estimate the gradient of a performance function of fuel flow versus control surface positions. In real-time operation, deflections of symmetric ailerons, trailing-edge flaps, and leading-edge flaps of an F/A-18 airplane are used for optimization of fuel flow. Results from six research flights are presented herein. The optimization algorithm found a trim configuration that required approximately 3 percent less fuel flow than the baseline trim at the same flight condition. This presentation also focuses on the design of the flight experiment and the practical challenges of conducting the experiment.

One-pot synthesis of reduced graphene oxide@boron nitride nanosheet hybrids with enhanced oxidation-resistant properties

NASA Astrophysics Data System (ADS)

Sun, Guoxun; Bi, Jianqiang; Wang, Weili; Zhang, Jingde

2017-12-01

Reduced graphene oxide@boron nitride nanosheet (RGO@BNNS) hybrids were prepared for the first time using template-assisted autoclave pyrolysis technique at the temperature as low as 600 °C. The developed method can be scaled into gram-scale synthesis of the material. The BNNSs combine with RGO through van der Waals interplanar interaction without damaging the structures of RGO. Such ultrathin BNNSs on the surface of RGO can serve as high-performance oxidation-resistant coatings in oxidizing atmospheres at high temperatures. The RGO@BNNS hybrids can sustain up to 800 °C over a relatively long period of time.

Microwave-assisted 'greener' synthesis of organics and nanomaterials

EPA Science Inventory

Microwave selective heating techniques in conjunction with greener reaction media are dramatically reducing chemical waste and reaction times in several organic transformations and material synthesis. This presentation summarizes author’s own experience in developing MW-assisted ...

What to Do until the Microprocesser Arrives.

ERIC Educational Resources Information Center

Barzilla, Frank

1983-01-01

Advises administrators how to develop an energy master plan and how to reduce the usage of heating, ventilating, and air conditioning (HVAC) systems by means of a time clock, thermostat, and a scheduled preventive maintenance program. (MLF)

Phase I development of an aesthetic, precast concrete bridge rail.

DOT National Transportation Integrated Search

2012-02-01

Precast concrete bridge rail systems offer several advantages over traditional cast-in-place rail designs, including reduced construction : time and costs, installation in a wide range of environmental conditions, easier maintenance and repair, impro...

Self-Calibrating Wave-Encoded Variable-Density Single-Shot Fast Spin Echo Imaging.

PubMed

Chen, Feiyu; Taviani, Valentina; Tamir, Jonathan I; Cheng, Joseph Y; Zhang, Tao; Song, Qiong; Hargreaves, Brian A; Pauly, John M; Vasanawala, Shreyas S

2018-04-01

It is highly desirable in clinical abdominal MR scans to accelerate single-shot fast spin echo (SSFSE) imaging and reduce blurring due to T 2 decay and partial-Fourier acquisition. To develop and investigate the clinical feasibility of wave-encoded variable-density SSFSE imaging for improved image quality and scan time reduction. Prospective controlled clinical trial. With Institutional Review Board approval and informed consent, the proposed method was assessed on 20 consecutive adult patients (10 male, 10 female, range, 24-84 years). A wave-encoded variable-density SSFSE sequence was developed for clinical 3.0T abdominal scans to enable high acceleration (3.5×) with full-Fourier acquisitions by: 1) introducing wave encoding with self-refocusing gradient waveforms to improve acquisition efficiency; 2) developing self-calibrated estimation of wave-encoding point-spread function and coil sensitivity to improve motion robustness; and 3) incorporating a parallel imaging and compressed sensing reconstruction to reconstruct highly accelerated datasets. Image quality was compared pairwise with standard Cartesian acquisition independently and blindly by two radiologists on a scale from -2 to 2 for noise, contrast, confidence, sharpness, and artifacts. The average ratio of scan time between these two approaches was also compared. A Wilcoxon signed-rank tests with a P value under 0.05 considered statistically significant. Wave-encoded variable-density SSFSE significantly reduced the perceived noise level and improved the sharpness of the abdominal wall and the kidneys compared with standard acquisition (mean scores 0.8, 1.2, and 0.8, respectively, P < 0.003). No significant difference was observed in relation to other features (P = 0.11). An average of 21% decrease in scan time was achieved using the proposed method. Wave-encoded variable-density sampling SSFSE achieves improved image quality with clinically relevant echo time and reduced scan time, thus providing a fast and robust approach for clinical SSFSE imaging. 1 Technical Efficacy: Stage 6 J. Magn. Reson. Imaging 2018;47:954-966. © 2017 International Society for Magnetic Resonance in Medicine.

Development of Fully Automated Low-Cost Immunoassay System for Research Applications.

PubMed

Wang, Guochun; Das, Champak; Ledden, Bradley; Sun, Qian; Nguyen, Chien

2017-10-01

Enzyme-linked immunosorbent assay (ELISA) automation for routine operation in a small research environment would be very attractive. A portable fully automated low-cost immunoassay system was designed, developed, and evaluated with several protein analytes. It features disposable capillary columns as the reaction sites and uses real-time calibration for improved accuracy. It reduces the overall assay time to less than 75 min with the ability of easy adaptation of new testing targets. The running cost is extremely low due to the nature of automation, as well as reduced material requirements. Details about system configuration, components selection, disposable fabrication, system assembly, and operation are reported. The performance of the system was initially established with a rabbit immunoglobulin G (IgG) assay, and an example of assay adaptation with an interleukin 6 (IL6) assay is shown. This system is ideal for research use, but could work for broader testing applications with further optimization.

Developing a spatial-temporal method for the geographic investigation of shoeprint evidence.

PubMed

Lin, Ge; Elmes, Gregory; Walnoha, Mike; Chen, Xiannian

2009-01-01

This article examines the potential of a spatial-temporal method for analysis of forensic shoeprint data. The large volume of shoeprint evidence recovered at crime scenes results in varied success in matching a print to a known shoe type and subsequently linking sets of matched prints to suspected offenders. Unlike DNA and fingerprint data, a major challenge is to reduce the uncertainty in linking sets of matched shoeprints to a suspected serial offender. Shoeprint data for 2004 were imported from the Greater London Metropolitan Area Bigfoot database into a geographic information system, and a spatial-temporal algorithm developed for this project. The results show that by using distance and time constraints interactively, the number of candidate shoeprints that can implicate one or few suspects can be substantially reduced. It concludes that the use of space-time and other ancillary information within a geographic information system can be quite helpful for forensic investigation.

Advanced Turbine Systems annual program review

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koop, W.E.

1995-10-01

Integrated High Performance Turbine Engine Technology (IHPTET) is a joint Air Force, Navy, Army, NASA, ARPA, and industry program focused on developing turbine engine technologies, with the goal of doubling propulsion capability by around the turn-of-the-century, and thus providing smaller, lighter, more durable, more affordable turbine engines in the future. IHPTET`s technology development plan for increasing propulsion capability with respect to time is divided into three phases. This phased approach reduces the technological risk of taking one giant leap, and also reduces the {open_quotes}political{close_quotes} risk of not delivering a product for an extended period of time, in that the phasingmore » allows continuous transfer of IHPTET technologies to our warfighters and continuous transfer to the commercial sector (dual-use). The IHPTET program addresses the three major classes of engines: turbofan/turbojet, turboshaft/turboprop, and expendables.« less

Developing a vacuum cooking equipment prototype to produce strawberry jam and optimization of vacuum cooking conditions.

PubMed

Okut, Dilara; Devseren, Esra; Koç, Mehmet; Ocak, Özgül Özdestan; Karataş, Haluk; Kaymak-Ertekin, Figen

2018-01-01

Purpose of this study was to develop prototype cooking equipment that can work at reduced pressure and to evaluate its performance for production of strawberry jam. The effect of vacuum cooking conditions on color soluble solid content, reducing sugars total sugars HMF and sensory properties were investigated. Also, the optimum vacuum cooking conditions for strawberry jam were optimized for Composite Rotatable Design. The optimum cooking temperature and time were determined targeting maximum soluble solid content and sensory attributes (consistency) and minimum Hue value and HMF content. The optimum vacuum cooking conditions determined were 74.4 °C temperature and 19.8 time. The soluble solid content strawberry jam made by vacuum process were similar to those prepared by traditional method. HMF contents of jams produced with vacuum cooking method were well within limit of standards.

Development of fast cooling pulsed magnets at the Wuhan National High Magnetic Field Center.

PubMed

Peng, Tao; Sun, Quqin; Zhao, Jianlong; Jiang, Fan; Li, Liang; Xu, Qiang; Herlach, Fritz

2013-12-01

Pulsed magnets with fast cooling channels have been developed at the Wuhan National High Magnetic Field Center. Between the inner and outer sections of a coil wound with a continuous length of CuNb wire, G10 rods with cross section 4 mm × 5 mm were inserted as spacers around the entire circumference, parallel to the coil axis. The free space between adjacent rods is 6 mm. The liquid nitrogen flows freely in the channels between these rods, and in the direction perpendicular to the rods through grooves provided in the rods. For a typical 60 T pulsed magnetic field with pulse duration of 40 ms, the cooling time between subsequent pulses is reduced from 160 min to 35 min. Subsequently, the same technology was applied to a 50 T magnet with 300 ms pulse duration. The cooling time of this magnet was reduced from 480 min to 65 min.

PIPELINEs: Creating Comparable Clinical Knowledge Efficiently by Linking Trial Platforms

PubMed Central

Shrier, AA; Antonijevic, Z; Beckman, RA; Campbell, RK; Chen, C; Flaherty, KT; Loewy, J; Lacombe, D; Madhavan, S; Selker, HP; Esserman, LJ

2016-01-01

Adaptive, seamless, multisponsor, multitherapy clinical trial designs executed as large scale platforms, could create superior evidence more efficiently than single‐sponsor, single‐drug trials. These trial PIPELINEs also could diminish barriers to trial participation, increase the representation of real‐world populations, and create systematic evidence development for learning throughout a therapeutic life cycle, to continually refine its use. Comparable evidence could arise from multiarm design, shared comparator arms, and standardized endpoints—aiding sponsors in demonstrating the distinct value of their innovative medicines; facilitating providers and patients in selecting the most appropriate treatments; assisting regulators in efficacy and safety determinations; helping payers make coverage and reimbursement decisions; and spurring scientists with translational insights. Reduced trial times and costs could enable more indications, reduced development cycle times, and improved system financial sustainability. Challenges to overcome range from statistical to operational to collaborative governance and data exchange. PMID:27643536

A hip abduction exercise prior to prolonged standing increased movement while reducing cocontraction and low back pain perception in those initially reporting low back pain.

PubMed

Viggiani, Daniel; Callaghan, Jack P

2016-12-01

Persons who develop low back pain from prolonged standing exhibit increased muscle cocontraction, decreased movement and increased spine extension. However, it is unclear how these factors relate to pain development. The purpose of this study was to use hip abductor fatigue to manipulate muscle activity patterns and determine its effects on standing behaviours and pain development. Forty participants stood for two hours twice, once following a hip abductor fatigue exercise (fatigue), and once without exercise beforehand (control). Trunk and gluteal muscle activity were measured to determine cocontraction. Lumbo-pelvic angles and force plates were used to assess posture and movement strategies. Visual analog scales differentiated pain (PDs) and non-pain developers (NPDs). PDs reported less low back pain during the fatigue session, with females having earlier reductions of similar scale than males. The fatigue session reduced gluteal and trunk cocontraction and increased centre of pressure movement; male and female PDs had opposing spine posture compensations. Muscle fatigue prior to standing reduced cocontraction, increased movement during standing and reduced the low back pain developed by PDs; the timing of pain reductions depended on spine postures adopted during standing. Copyright © 2016 Elsevier Ltd. All rights reserved.

The RhoGEF Net1 Is Required for Normal Mammary Gland Development

PubMed Central

Zuo, Yan; Berdeaux, Rebecca

2014-01-01

Neuroepithelial transforming gene 1 (Net1) is a RhoA subfamily-specific guanine nucleotide exchange factor that is overexpressed in human breast cancer and is required for breast cancer cell migration and invasion. However, the role of Net1 in normal mammary gland development or function has never been assessed. To understand the role of Net1 in the mammary gland, we have created a conditional Net1 knockout mouse model. Whole-body deletion of Net1 results in delayed mammary gland development during puberty characterized by slowed of ductal extension and reduced ductal branching. Epithelial cells within the developing ducts show reduced proliferation that is accompanied by diminished estrogen receptor-α expression and activity. Net1-deficient mammary glands also exhibit reduced phosphorylation of regulatory subunits of myosin light chain and myosin light-chain phosphatase, indicating that RhoA-dependent actomyosin contraction is compromised. Net1 deficiency also leads to disorganization of myoepithelial and ductal epithelial cells and increased periductal collagen deposition. Mammary epithelial cell transplantation experiments indicate that reduced ductal branching and disorganization are cell autonomous. These data identify for the first time a role for NET1 in vivo and indicate that NET1 expression is essential for the proliferation and differentiation of mammary epithelial cells in the developing mammary gland. PMID:25321414

A knowledge-based design framework for airplane conceptual and preliminary design

NASA Astrophysics Data System (ADS)

Anemaat, Wilhelmus A. J.

The goal of work described herein is to develop the second generation of Advanced Aircraft Analysis (AAA) into an object-oriented structure which can be used in different environments. One such environment is the third generation of AAA with its own user interface, the other environment with the same AAA methods (i.e. the knowledge) is the AAA-AML program. AAA-AML automates the initial airplane design process using current AAA methods in combination with AMRaven methodologies for dependency tracking and knowledge management, using the TechnoSoft Adaptive Modeling Language (AML). This will lead to the following benefits: (1) Reduced design time: computer aided design methods can reduce design and development time and replace tedious hand calculations. (2) Better product through improved design: more alternative designs can be evaluated in the same time span, which can lead to improved quality. (3) Reduced design cost: due to less training and less calculation errors substantial savings in design time and related cost can be obtained. (4) Improved Efficiency: the design engineer can avoid technically correct but irrelevant calculations on incomplete or out of sync information, particularly if the process enables robust geometry earlier. Although numerous advancements in knowledge based design have been developed for detailed design, currently no such integrated knowledge based conceptual and preliminary airplane design system exists. The third generation AAA methods are tested over a ten year period on many different airplane designs. Using AAA methods will demonstrate significant time savings. The AAA-AML system will be exercised and tested using 27 existing airplanes ranging from single engine propeller, business jets, airliners, UAV's to fighters. Data for the varied sizing methods will be compared with AAA results, to validate these methods. One new design, a Light Sport Aircraft (LSA), will be developed as an exercise to use the tool for designing a new airplane. Using these tools will show an improvement in efficiency over using separate programs due to the automatic recalculation with any change of input data. The direct visual feedback of 3D geometry in the AAA-AML, will lead to quicker resolving of problems as opposed to conventional methods.

Estimation Accuracy on Execution Time of Run-Time Tasks in a Heterogeneous Distributed Environment.

PubMed

Liu, Qi; Cai, Weidong; Jin, Dandan; Shen, Jian; Fu, Zhangjie; Liu, Xiaodong; Linge, Nigel

2016-08-30

Distributed Computing has achieved tremendous development since cloud computing was proposed in 2006, and played a vital role promoting rapid growth of data collecting and analysis models, e.g., Internet of things, Cyber-Physical Systems, Big Data Analytics, etc. Hadoop has become a data convergence platform for sensor networks. As one of the core components, MapReduce facilitates allocating, processing and mining of collected large-scale data, where speculative execution strategies help solve straggler problems. However, there is still no efficient solution for accurate estimation on execution time of run-time tasks, which can affect task allocation and distribution in MapReduce. In this paper, task execution data have been collected and employed for the estimation. A two-phase regression (TPR) method is proposed to predict the finishing time of each task accurately. Detailed data of each task have drawn interests with detailed analysis report being made. According to the results, the prediction accuracy of concurrent tasks' execution time can be improved, in particular for some regular jobs.

A Fuzzy Control System for Reducing Urban Runoff by a Stormwater Storage Tank

NASA Astrophysics Data System (ADS)

Zhang, P.; Cai, Y.; Wang, J.

2017-12-01

Stormwater storage tank (SST) is a popular low impact development technology for reducing stormwater runoff in the construction of sponge city. Most researches on SST were mainly the design, pollutants removal effect, and operation assessment. While there were few researches on the automatic control of SST for reducing peak flow. In this paper, fuzzy control was introduced into the peak control of SST to improve the efficiency of reducing stormawter runoff. Firstly, the design of SST was investigated. A catchment area and return period were assumed, a SST model was manufactured, and then the storage capacity of the SST was verified. Secondly, the control parameters of the SST based on reducing stormwater runoff was analyzed, and a schematic diagram of real-time control (RTC) system based on peak control SST was established. Finally, fuzzy control system of a double input (flow and water level) and double output (inlet and outlet valve) was designed. The results showed that 1) under the different return periods (one year, three years, five years), the SST had the effect of delayed peak control and storage by increasing the detention time, 2) rainfall, pipeline flow, the influent time and the water level in the SST could be used as RTC parameters, and 3) the response curves of flow velocity and water level fluctuated very little and reached equilibrium in a short time. The combination of online monitoring and fuzzy control was feasible to control the SST automatically. This paper provides a theoretical reference for reducing stormwater runoff and improving the operation efficiency of SST.

Increasing Testing Efficiency through the Development of an IT-Based Adaptive Testing Tool for Competency Measurement

ERIC Educational Resources Information Center

Kleinhans, Janne; Schumann, Matthias

2015-01-01

Purpose: This paper investigates the potential of computerized adaptive testing for CMs to reduce test time. In the context of education and training, competency measurement (CM) is a central challenge in competency management. For complex CMs, a compromise must be addressed between the time available and the quality of the measurements.…

System Developed for Real-Time Blade-Flutter Monitoring in the Wind Tunnel

NASA Technical Reports Server (NTRS)

Kurkov, Anatole P.; Dhadwal, Harbans S.; Radzikowski, mark; Strukov, Dmitri

2005-01-01

A real-time system has been developed to monitor flutter vibrations in turbomachinery. The system is designed for continuous processing of blade tip timing data at a rate of 10 MB/sec. A USB 2.0 interface provides uninterrupted real-time processing of the data, and the blade-tip arrival times are measured with a 50-MHz oscillator and a 24-bit pipelined architecture counter. The input stage includes a glitch catcher, which reduces the probability of detecting a ghost blade to negligible levels. A graphical user interface provides online interrogation of any blade tip from any light probe sensor. Alternatively, data from all blades and all sensors can be superimposed into a single composite scatter plot displaying the vibration amplitude of each blade.

Crowding of Drosophila larvae affects lifespan and other life-history traits via reduced availability of dietary yeast.

PubMed

Klepsatel, Peter; Procházka, Emanuel; Gáliková, Martina

2018-06-19

Conditions experienced during development have often long-lasting effects persisting into adulthood. In Drosophila, it is well-documented that larval crowding influences fitness-related traits such as body size, starvation resistance and lifespan. However, the underlying mechanism of this phenomenon is not well understood. Here, we show that the effects of increased larval density on life-history traits can be explained by decreased yeast availability in the diet during development. Yeast-poor larval diet alters various life-history traits and mimics the effects of larval crowding. In particular, reduced amount of yeast in larval diet prolongs developmental time, reduces body size, increases body fat content and starvation resistance, and prolongs Drosophila lifespan. Conversely, the effects of larval crowding can be rescued by increasing the concentration of the dietary yeast in the diet during development. Altogether, our results show that the well-known effects of larval crowding on life-history traits are mainly caused by the reduced availability of dietary yeasts due to increased larval competition. Copyright © 2018. Published by Elsevier Inc.

Why Older Adults Spend Time Sedentary and Break Their Sedentary Behavior: A Mixed-Methods Approach Using Life-Logging Equipment.

PubMed

Dontje, Manon L; Leask, Calum F; Harvey, Juliet; Skelton, Dawn A; Chastin, Sebastien F M

2018-04-01

Older adults are recommended to reduce their sedentary time to promote healthy ageing. To develop effective interventions identifying when, why, and how older adults are able to change their sitting habits is important. The aim of this mixed-method study was to improve our understanding of reasons for (breaking) sedentary behavior in older adults. Thirty older adults (74.0 [±5.3] years old, 73% women) were asked about their believed reasons for (breaking) sedentary behavior, and about their actual reasons when looking at a personal storyboard with objective records of activPAL monitor data and time-lapse camera pictures showing all their periods of sedentary time in a day. The most often mentioned believed reason for remaining sedentary was television/radio (mentioned by 48.3%), while eating/drinking was most often mentioned as actual reason (96.6%). Only 17.2% believed that food/tea preparation was a reason to break up sitting, while this was an actual reason for 82.8% of the study sample. Results of this study show that there is a discrepancy between believed and actual reasons for (breaking) sedentary behavior. These findings suggest developing interventions utilizing the actual reasons for breaking sedentary behavior to reduce sedentary time in older adults.

Advancing solar energy forecasting through the underlying physics

NASA Astrophysics Data System (ADS)

Yang, H.; Ghonima, M. S.; Zhong, X.; Ozge, B.; Kurtz, B.; Wu, E.; Mejia, F. A.; Zamora, M.; Wang, G.; Clemesha, R.; Norris, J. R.; Heus, T.; Kleissl, J. P.

2017-12-01

As solar power comprises an increasingly large portion of the energy generation mix, the ability to accurately forecast solar photovoltaic generation becomes increasingly important. Due to the variability of solar power caused by cloud cover, knowledge of both the magnitude and timing of expected solar power production ahead of time facilitates the integration of solar power onto the electric grid by reducing electricity generation from traditional ancillary generators such as gas and oil power plants, as well as decreasing the ramping of all generators, reducing start and shutdown costs, and minimizing solar power curtailment, thereby providing annual economic value. The time scales involved in both the energy markets and solar variability range from intra-hour to several days ahead. This wide range of time horizons led to the development of a multitude of techniques, with each offering unique advantages in specific applications. For example, sky imagery provides site-specific forecasts on the minute-scale. Statistical techniques including machine learning algorithms are commonly used in the intra-day forecast horizon for regional applications, while numerical weather prediction models can provide mesoscale forecasts on both the intra-day and days-ahead time scale. This talk will provide an overview of the challenges unique to each technique and highlight the advances in their ongoing development which come alongside advances in the fundamental physics underneath.

Link monitor and control operator assistant: A prototype demonstrating semiautomated monitor and control

NASA Technical Reports Server (NTRS)

Lee, L. F.; Cooper, L. P.

1993-01-01

This article describes the approach, results, and lessons learned from an applied research project demonstrating how artificial intelligence (AI) technology can be used to improve Deep Space Network operations. Configuring antenna and associated equipment necessary to support a communications link is a time-consuming process. The time spent configuring the equipment is essentially overhead and results in reduced time for actual mission support operations. The NASA Office of Space Communications (Code O) and the NASA Office of Advanced Concepts and Technology (Code C) jointly funded an applied research project to investigate technologies which can be used to reduce configuration time. This resulted in the development and application of AI-based automated operations technology in a prototype system, the Link Monitor and Control Operator Assistant (LMC OA). The LMC OA was tested over the course of three months in a parallel experimental mode on very long baseline interferometry (VLBI) operations at the Goldstone Deep Space Communications Center. The tests demonstrated a 44 percent reduction in pre-calibration time for a VLBI pass on the 70-m antenna. Currently, this technology is being developed further under Research and Technology Operating Plan (RTOP)-72 to demonstrate the applicability of the technology to operations in the entire Deep Space Network.

Gambling on growth.

PubMed

Feeney, A

1990-01-01

When the assumption is made that economic growth must be increased by 10% to accommodate population increases and to reduce poverty, the question is raised as to whether or not sustainable development is possible. The human population increased 3 times since 1900, and global economic activity has increased 7 times faster than population. Use of fossil fuels has increased by 30 times, and industrial production has increased by 50 times. The by-products of population growth and economic activity are loss of tropical rainforests; species extinction; desertification in Africa, India, and the US; toxic and radioactive pollution; and greenhouse warming and ozone depletion. The atmosphere's stability and human habitation is threatened. Sustainable development, as defined by the World Commission on Environment and Development (WCED) in "Our Common Future," is meeting present needs but not at the expense of future needs. Economic growth must proceed at different rates in different countries to close the gap between the rich and poor. Economic expansion has been criticized by the president of Negative Population Growth and the Environmental Defense Fund's coordinator of reform for the World Bank's environmental policies and Third World countries. US government response during the Reagan administration has been indifference, while support has come from the World Resources Institute, the Worldwatch Institute, the US National Wildlife Federation, and the Population Reference Bureau. Recent support has come from signers of the "G-7 Summit" and from IBM and the Dow Chemical Company. A few shared tenets are 1) that economic development is not sustainable, 2) environmental reforms are necessary to make development sustainable, 3) a trade-off is needed to increase Third World energy use, and 4) population must be stabilized. Many proposals have been offered including reducing population to 2 billion, or 40% of the current level. Reducing poverty globally is an environmentally sound policy. High tariffs and protectionism, debt payments, and International Monetary Fund structural adjustment programs have made the situation worse for the Third World. Many suggestions have been made to correct the poverty imbalance, including no growth or steady state economics.

Mental health inpatients' and staff members' suggestions for reducing physical restraint: A qualitative study.

PubMed

Wilson, C; Rouse, L; Rae, S; Kar Ray, M

2018-04-01

WHAT IS KNOWN ON THE SUBJECT?: Restraint has negative psychological, physical and relational consequences for mental health patients and staff. Restraint reduction interventions have been developed (e.g., "Safewards"). Limited qualitative research has explored suggestions on how to reduce physical restraint (and feasibility issues with implementing interventions) from those directly involved. WHAT DOES THIS PAPER ADD TO EXISTING KNOWLEDGE?: This paper explores mental health patients' and staff members' suggestions for reducing physical restraint, whilst addressing barriers to implementing these. Findings centred on four themes: improving communication and relationships; staffing factors; environment and space; and activities and distraction. Not all suggestions are addressed by currently available interventions. Barriers to implementation were identified, centring on a lack of time and/or resources; with the provision of more time for staff to spend with patients and implement interventions seen as essential to reducing physical restraint. WHAT ARE THE IMPLICATIONS FOR PRACTICE?: Improving communication and relationships between staff/patients, making staffing-related changes, improving ward environments and providing patient activities are central to restraint reduction in mental healthcare. Fundamental issues related to understaffing, high staff turnover, and lack of time and resources need addressing in order for suggestions to be successfully implemented. Introduction Physical restraint has negative consequences for all involved, and international calls for its reduction have emerged. Some restraint reduction interventions have been developed, but limited qualitative research explores suggestions on how to reduce physical restraint (and feasibility issues with implementation) from those directly involved. Aims To explore mental health patients' and staff members' suggestions for reducing physical restraint. Methods Interviews were conducted with 13 inpatients and 22 staff members with experience of restraint on adult mental health inpatient wards in one UK National Health Service Trust. Results Findings centred on four overarching themes: improving communication and relationships between staff/patients; making staff-related changes; improving ward environments/spaces; and having more activities. However, concerns were raised around practicalities/feasibility of their implementation. Discussion Continued research is needed into best ways to reduce physical restraint, with an emphasis on feasibility/practicality and how to make time in busy ward environments. Implications for Practice Improving communication and relationships between staff/patients, making staffing-related changes, improving ward environments and providing patient activities are central to restraint reduction in mental healthcare. However, fundamental issues related to understaffing, high staff turnover and lack of time/resources need addressing in order for these suggestions to be successfully implemented. © 2018 John Wiley & Sons Ltd.

Surgical scheduling: a lean approach to process improvement.

PubMed

Simon, Ross William; Canacari, Elena G

2014-01-01

A large teaching hospital in the northeast United States had an inefficient, paper-based process for scheduling orthopedic surgery that caused delays and contributed to site/side discrepancies. The hospital's leaders formed a team with the goals of developing a safe, effective, patient-centered, timely, efficient, and accurate orthopedic scheduling process; smoothing the schedule so that block time was allocated more evenly; and ensuring correct site/side. Under the resulting process, real-time patient information is entered into a database during the patient's preoperative visit in the surgeon's office. The team found the new process reduced the occurrence of site/side discrepancies to zero, reduced instances of changing the sequence of orthopedic procedures by 70%, and increased patient satisfaction. Copyright © 2014 AORN, Inc. Published by Elsevier Inc. All rights reserved.

Expert Systems In Medical Studies - A New Twist

NASA Astrophysics Data System (ADS)

Slagle, James R.; Long, John M.; Wick, Michael R.; Matts, John P.; Leon, Arthur S.

1986-03-01

The use of experts to evaluate large amounts of trial data results in increasingly expensive and time consuming research. We are investigating the role expert systems can play in reducing the time and expense of research projects. Current methods in large clinical studies for evaluating data are often crude and superficial. We have developed, for a large clinical trial, an expert system for analysis of treadmill exercise ECG test results. In the cases we are studying, a patient is given a treadmill exercise ECG test once a year for five years. Pairs of these exercise tests are then evaluated by cardiologists to determine the condition of the patient's heart. The results of our system show great promise for the use of expert systems in reducing the time and expense of large clinical trials.

Development of efficient time-evolution method based on three-term recurrence relation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Akama, Tomoko, E-mail: a.tomo---s-b-l-r@suou.waseda.jp; Kobayashi, Osamu; Nanbu, Shinkoh, E-mail: shinkoh.nanbu@sophia.ac.jp

The advantage of the real-time (RT) propagation method is a direct solution of the time-dependent Schrödinger equation which describes frequency properties as well as all dynamics of a molecular system composed of electrons and nuclei in quantum physics and chemistry. Its applications have been limited by computational feasibility, as the evaluation of the time-evolution operator is computationally demanding. In this article, a new efficient time-evolution method based on the three-term recurrence relation (3TRR) was proposed to reduce the time-consuming numerical procedure. The basic formula of this approach was derived by introducing a transformation of the operator using the arcsine function.more » Since this operator transformation causes transformation of time, we derived the relation between original and transformed time. The formula was adapted to assess the performance of the RT time-dependent Hartree-Fock (RT-TDHF) method and the time-dependent density functional theory. Compared to the commonly used fourth-order Runge-Kutta method, our new approach decreased computational time of the RT-TDHF calculation by about factor of four, showing the 3TRR formula to be an efficient time-evolution method for reducing computational cost.« less

Within- and trans-generational plasticity: seed germination responses to light quantity and quality.

PubMed

Vayda, Katherine; Donohue, Kathleen; Auge, Gabriela Alejandra

2018-06-01

Plants respond not only to the environment in which they find themselves, but also to that of their parents. The combination of within- and trans-generational phenotypic plasticity regulates plant development. Plants use light as source of energy and also as a cue of competitive conditions, since the quality of light (ratio of red to far-red light, R:FR) indicates the presence of neighbouring plants. Light regulates many aspects of plant development, including seed germination. To understand how seeds integrate environmental cues experienced at different times, we quantified germination responses to changes in light quantity (irradiance) and quality (R:FR) experienced during seed maturation and seed imbibition in Arabidopsis thaliana genotypes that differ in their innate dormancy levels and after treatments that break or reinduce dormancy. In two of the genotypes tested, reduced irradiance as well as reduced R:FR during seed maturation induced higher germination; thus, the responses to light quantity and R:FR reinforced each other. In contrast, in a third genotype, reduced irradiance during seed maturation induced progeny germination, but response to reduced R:FR was in the opposite direction, leading to a very weak or no overall effect of a simulated canopy experienced by the mother plant. During seed imbibition, reduced irradiance and reduced R:FR caused lower germination in all genotypes. Therefore, responses to light experienced at different times (maturation vs. imbibition) can have opposite effects. In summary, seeds responded both to light resources (irradiance) and to cues of competition (R:FR), and trans-generational plasticity to light frequently opposed and was stronger than within-generation plasticity.

A Recurrent Probabilistic Neural Network with Dimensionality Reduction Based on Time-series Discriminant Component Analysis.

PubMed

Hayashi, Hideaki; Shibanoki, Taro; Shima, Keisuke; Kurita, Yuichi; Tsuji, Toshio

2015-12-01

This paper proposes a probabilistic neural network (NN) developed on the basis of time-series discriminant component analysis (TSDCA) that can be used to classify high-dimensional time-series patterns. TSDCA involves the compression of high-dimensional time series into a lower dimensional space using a set of orthogonal transformations and the calculation of posterior probabilities based on a continuous-density hidden Markov model with a Gaussian mixture model expressed in the reduced-dimensional space. The analysis can be incorporated into an NN, which is named a time-series discriminant component network (TSDCN), so that parameters of dimensionality reduction and classification can be obtained simultaneously as network coefficients according to a backpropagation through time-based learning algorithm with the Lagrange multiplier method. The TSDCN is considered to enable high-accuracy classification of high-dimensional time-series patterns and to reduce the computation time taken for network training. The validity of the TSDCN is demonstrated for high-dimensional artificial data and electroencephalogram signals in the experiments conducted during the study.

Nuclear electric propulsion: A better, safer, cheaper transportation system for human exploration of Mars

NASA Technical Reports Server (NTRS)

Clark, John S.; George, Jeffrey A.; Gefert, Leon P.; Doherty, Michael P.; Sefcik, Robert J.

1994-01-01

NASA has completed a preliminary mission and systems study of nuclear electric propulsion (NEP) systems for 'split-sprint' human exploration and related robotic cargo missions to Mars. This paper describes the study, the mission architecture selected, the NEP system and technology development needs, proposed development schedules, and estimated development costs. Since current administration policy makers have delayed funding for key technology development activities that could make Mars exploration missions a reality in the near future, NASA will have time to evaluate various alternate mission options, and it appears prudent to ensure that Mars mission plans focus on astronaut and mission safety, while reducing costs to acceptable levels. The split-sprint nuclear electric propulsion system offers trip times comparable to nuclear thermal propulsion (NTP) systems, while providing mission abort opportunities that are not possible with 'reference' mission architectures. Thus, NEP systems offer short transit times for the astronauts, reducing the exposure of the crew to intergalactic cosmic radiation. The high specific impulse of the NEP system, which leads to very low propellant requirements, results in significantly lower 'initial mass in low earth orbit' (IMLEO). Launch vehicle packaging studies show that the NEP system can be launched, assembled, and deployed, with about one less 240-metric-ton heavy lift launch vehicle (HLLV) per mission opportunity - a very Technology development cost of the nuclear reactor for an NEP system would be shared with the proposed nuclear surface power systems, since nuclear systems will be required to provide substantial electrical power on the surface of Mars. The NEP development project plan proposed includes evolutionary technology development for nuclear electric propulsion systems that expands upon SP-100 (Space Power - 100 kw(e)) technology that has been developed for lunar and Mars surface nuclear power, and small NEP systems for interplanetary probes. System upgrades are expected to evolve that will result in even shorter trip times, improved payload capabilities, and enhanced safety and reliability.

Development of an automated ultrasonic testing system

NASA Astrophysics Data System (ADS)

Shuxiang, Jiao; Wong, Brian Stephen

2005-04-01

Non-Destructive Testing is necessary in areas where defects in structures emerge over time due to wear and tear and structural integrity is necessary to maintain its usability. However, manual testing results in many limitations: high training cost, long training procedure, and worse, the inconsistent test results. A prime objective of this project is to develop an automatic Non-Destructive testing system for a shaft of the wheel axle of a railway carriage. Various methods, such as the neural network, pattern recognition methods and knowledge-based system are used for the artificial intelligence problem. In this paper, a statistical pattern recognition approach, Classification Tree is applied. Before feature selection, a thorough study on the ultrasonic signals produced was carried out. Based on the analysis of the ultrasonic signals, three signal processing methods were developed to enhance the ultrasonic signals: Cross-Correlation, Zero-Phase filter and Averaging. The target of this step is to reduce the noise and make the signal character more distinguishable. Four features: 1. The Auto Regressive Model Coefficients. 2. Standard Deviation. 3. Pearson Correlation 4. Dispersion Uniformity Degree are selected. And then a Classification Tree is created and applied to recognize the peak positions and amplitudes. Searching local maximum is carried out before feature computing. This procedure reduces much computation time in the real-time testing. Based on this algorithm, a software package called SOFRA was developed to recognize the peaks, calibrate automatically and test a simulated shaft automatically. The automatic calibration procedure and the automatic shaft testing procedure are developed.

Study of residue type defect formation mechanism and the effect of advanced defect reduction (ADR) rinse process

NASA Astrophysics Data System (ADS)

Arima, Hiroshi; Yoshida, Yuichi; Yoshihara, Kosuke; Shibata, Tsuyoshi; Kushida, Yuki; Nakagawa, Hiroki; Nishimura, Yukio; Yamaguchi, Yoshikazu

2009-03-01

Residue type defect is one of yield detractors in lithography process. It is known that occurrence of the residue type defect is dependent on resist development process and the defect is reduced by optimized rinsing condition. However, the defect formation is affected by resist materials and substrate conditions. Therefore, it is necessary to optimize the development process condition by each mask level. Those optimization steps require a large amount of time and effort. The formation mechanism is investigated from viewpoint of both material and process. The defect formation is affected by resist material types, substrate condition and development process condition (D.I.W. rinse step). Optimized resist formulation and new rinse technology significantly reduce the residue type defect.

Custom FPGA processing for real-time fetal ECG extraction and identification.

PubMed

Torti, E; Koliopoulos, D; Matraxia, M; Danese, G; Leporati, F

2017-01-01

Monitoring the fetal cardiac activity during pregnancy is of crucial importance for evaluating fetus health. However, there is a lack of automatic and reliable methods for Fetal ECG (FECG) monitoring that can perform this elaboration in real-time. In this paper, we present a hardware architecture, implemented on the Altera Stratix V FPGA, capable of separating the FECG from the maternal ECG and to correctly identify it. We evaluated our system using both synthetic and real tracks acquired from patients beyond the 20th pregnancy week. This work is part of a project aiming at developing a portable system for FECG continuous real-time monitoring. Its characteristics of reduced power consumption, real-time processing capability and reduced size make it suitable to be embedded in the overall system, that is the first proposed exploiting Blind Source Separation with this technology, to the best of our knowledge. Copyright © 2016 Elsevier Ltd. All rights reserved.

Flat-plate solar array project process development area: Process research of non-CZ silicon material

NASA Technical Reports Server (NTRS)

Campbell, R. B.

1986-01-01

Several different techniques to simultaneously diffuse the front and back junctions in dendritic web silicon were investigated. A successful simultaneous diffusion reduces the cost of the solar cell by reducing the number of processing steps, the amount of capital equipment, and the labor cost. The three techniques studied were: (1) simultaneous diffusion at standard temperatures and times using a tube type diffusion furnace or a belt furnace; (2) diffusion using excimer laser drive-in; and (3) simultaneous diffusion at high temperature and short times using a pulse of high intensity light as the heat source. The use of an excimer laser and high temperature short time diffusion experiment were both more successful than the diffusion at standard temperature and times. The three techniques are described in detail and a cost analysis of the more successful techniques is provided.

Evaluation of a patient navigation program.

PubMed

Koh, Catherine; Nelson, Joan M; Cook, Paul F

2011-02-01

This study examined the value and effectiveness of a patient navigation program in terms of timeliness of access to cancer care, resolution of barriers, and satisfaction in 55 patients over a six-month period. Although not statistically significant, the time interval between diagnostic biopsy to first consultation with a cancer specialist after program implementation was reduced from an average of 14.6 days to 12.8 days. The time interval between diagnostic biopsy to initiation of cancer treatment also was reduced from 30 days to 26.2 days (not statistically significant). In addition, 71% of patient barriers were resolved by the time treatment was initiated. Overall, patients were highly satisfied with their navigated care experience. Consistent evaluation and monitoring of quality-of-care indicators are critical to further develop the program and to direct resource allocation. Oncology nurses participating in patient navigation programs should be encouraged to evaluate their importance and impact in this developing concept. Nurses should seek roles that allow them to optimize the effective use of their specialized knowledge and skills to the benefit of patients along the cancer care continuum.

Development of a geotechnical information database : technical summary report.

DOT National Transportation Integrated Search

2009-08-01

The knowledge of existing soil conditions prior to road and bridge construction can : reduce construction cost, time, and headaches. The field data and laboratory results : collected far in advance of project construction are often slow to reach the ...

Chemical activation by mechanochemical mixing, microwave, and ultrasonic irradiation

EPA Science Inventory

The use of emerging MW-assisted chemistry techniques in conjunction with benign reaction media is dramatically reducing chemical waste ad reaction times in several organic syntheses and chemical transformations. This editorial comments on the recent developments in mechanochemica...

Turbulent structure in low-concentration drag-reducing channel flows

NASA Technical Reports Server (NTRS)

Luchik, T. S.; Tiederman, W. G.

1988-01-01

A two-component laser-Doppler velocimeter was used to obtain simultaneous measurements of the velocity components parallel and normal to the wall in two fully developed well-mixed low-concentration drag-reducing channel flows and one turbulent channel flow. For the drag-reducing flows, the average time between bursts was found to increase. Although the basic structure of the fundamental momentum transport event is shown to be the same in these drag-reducing flows, the lower-threshold Reynolds-stress-producing motions were found to be damped, while the higher-threshold motions were not. It is suggested that some strong turbulent motions are needed to maintain extended polymer molecules, which produce a solution with properties that can damp lower threshold turbulence and thereby reduce viscous drag.

Low Cost Upper Stage-Class Propulsion (LCUSP)

NASA Technical Reports Server (NTRS)

Vickers, John

2015-01-01

NASA is making space exploration more affordable and viable by developing and utilizing innovative manufacturing technologies. Technology development efforts at NASA in propulsion are committed to continuous innovation of design and manufacturing technologies for rocket engines in order to reduce the cost of NASA's journey to Mars. The Low Cost Upper Stage-Class Propulsion (LCUSP) effort will develop and utilize emerging Additive Manufacturing (AM) to significantly reduce the development time and cost for complex rocket propulsion hardware. Benefit of Additive Manufacturing (3-D Printing) Current rocket propulsion manufacturing techniques are costly and have lengthy development times. In order to fabricate rocket engines, numerous complex parts made of different materials are assembled in a way that allow the propellant to collect heat at the right places to drive the turbopump and simultaneously keep the thrust chamber from melting. The heat conditioned fuel and oxidizer come together and burn inside the combustion chamber to provide thrust. The efforts to make multiple parts precisely fit together and not leak after experiencing cryogenic temperatures on one-side and combustion temperatures on the other is quite challenging. Additive manufacturing has the potential to significantly reduce the time and cost of making rocket parts like the copper liner and Nickel-alloy jackets found in rocket combustion chambers where super-cold cryogenic propellants are heated and mixed to the extreme temperatures needed to propel rockets in space. The Selective Laser Melting (SLM) machine fuses 8,255 layers of copper powder to make a section of the chamber in 10 days. Machining an equivalent part and assembling it with welding and brazing techniques could take months to accomplish with potential failures or leaks that could require fixes. The design process is also enhanced since it does not require the 3D model to be converted to 2-D drawings. The design and fabrication process can be sped up and improved with fewer errors to be accomplished in weeks instead of months.

Participatory Workplace Interventions Can Reduce Sedentary Time for Office Workers—A Randomised Controlled Trial

PubMed Central

Parry, Sharon; Straker, Leon; Gilson, Nicholas D.; Smith, Anne J.

2013-01-01

Background Occupational sedentary behaviour is an important contributor to overall sedentary risk. There is limited evidence for effective workplace interventions to reduce occupational sedentary time and increase light activity during work hours. The purpose of the study was to determine if participatory workplace interventions could reduce total sedentary time, sustained sedentary time (bouts >30 minutes), increase the frequency of breaks in sedentary time and promote light intensity activity and moderate/vigorous activity (MVPA) during work hours. Methods A randomised controlled trial (ANZCTR number: ACTN12612000743864) was conducted using clerical, call centre and data processing workers (n = 62, aged 25–59 years) in 3 large government organisations in Perth, Australia. Three groups developed interventions with a participatory approach: ‘Active office’ (n = 19), ‘Active Workstation’ and promotion of incidental office activity; ‘Traditional physical activity’ (n = 14), pedometer challenge to increase activity between productive work time and ‘Office ergonomics’ (n = 29), computer workstation design and breaking up computer tasks. Accelerometer (ActiGraph GT3X, 7 days) determined sedentary time, sustained sedentary time, breaks in sedentary time, light intensity activity and MVPA on work days and during work hours were measured before and following a 12 week intervention period. Results For all participants there was a significant reduction in sedentary time on work days (−1.6%, p = 0.006) and during work hours (−1.7%, p = 0.014) and a significant increase in number of breaks/sedentary hour on work days (0.64, p = 0.005) and during work hours (0.72, p = 0.015); there was a concurrent significant increase in light activity during work hours (1.5%, p = 0.012) and MVPA on work days (0.6%, p = 0.012). Conclusions This study explored novel ways to modify work practices to reduce occupational sedentary behaviour. Participatory workplace interventions can reduce sedentary time, increase the frequency of breaks and improve light activity and MVPA of office workers by using a variety of interventions. Trial Registration Australian New Zealand Clinical Trials Registry ACTN12612000743864. PMID:24265734

SEASAT economic assessment. Volume 6: Arctic operations case study and generalization. [economic benefits of SEASAT satellites to oil exploration in the Arctic

NASA Technical Reports Server (NTRS)

1975-01-01

The hypothetical development and transportation of Arctic oil and other resources by ice breaking super tanker fleets to the continental East Coast are discussed. The utilization of SEASAT ice mapping data is shown to contribute to a more effective transportation operation through the Arctic ice by reducing transportation costs as a consequence of reduced transit time per voyage.

Innovation in Building Design

NASA Technical Reports Server (NTRS)

1983-01-01

Thomas & Betts Corporation's Flat Conductor Cables, or FCC, were developed of necessity as aircraft and spacecraft became increasingly complex. In order to reduce size and weight of components, the use of thin flat wire instead of relatively thick and protrusive round cable, provided a dramatic reduction of the space occupied by the many miles of power distribution lines in an aerospace vehicle. Commercially, FCC offers cost savings in simplified building construction, reduced installation time and ease of alteration.

Imaging MS Methodology for More Chemical Information in Less Data Acquisition Time Utilizing a Hybrid Linear Ion Trap-Orbitrap Mass Spectrometer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Perdian, D. C.; Lee, Young Jin

2010-11-15

A novel mass spectrometric imaging method is developed to reduce the data acquisition time and provide rich chemical information using a hybrid linear ion trap-orbitrap mass spectrometer. In this method, the linear ion trap and orbitrap are used in tandem to reduce the acquisition time by incorporating multiple linear ion trap scans during an orbitrap scan utilizing a spiral raster step plate movement. The data acquisition time was decreased by 43-49% in the current experiment compared to that of orbitrap-only scans; however, 75% or more time could be saved for higher mass resolution and with a higher repetition rate laser.more » Using this approach, a high spatial resolution of 10 {micro}m was maintained at ion trap imaging, while orbitrap spectra were acquired at a lower spatial resolution, 20-40 {micro}m, all with far less data acquisition time. Furthermore, various MS imaging methods were developed by interspersing MS/MS and MSn ion trap scans during orbitrap scans to provide more analytical information on the sample. This method was applied to differentiate and localize structural isomers of several flavonol glycosides from an Arabidopsis flower petal in which MS/MS, MSn, ion trap, and orbitrap images were all acquired in a single data acquisition.« less

Quantitative inheritance of crop timing traits in interspecific hybrid Petunia populations and interactions with crop quality parameters.

PubMed

Warner, Ryan M; Walworth, Aaron E

2010-01-01

The leaf unfolding rate (i.e., development rate) and the number of nodes forming prior to floral initiation are 2 factors determining production times for floriculture crops. Wild relative species of the cultivated petunia (Petunia x hybrida Vilm.) that exhibited faster development rates than modern cultivars and may therefore be useful genetic sources to develop cultivars with decreased production time were identified. Three interspecific F(2) families, Petunia exserta Stehmann x P. axillaris (Lam.) Britton et al., P. x hybrida 'Mitchell' x P. axillaris, and P. axillaris x P. integrifolia (Hook.) Schinz & Thell. all exhibited transgressive segregation for development rate and node number below the first flower. Development rate and time to flower segregated independently in all families. Leaf number below the first flower was positively correlated with leaf unfolding rate in all families except P. axillaris x P. integrifolia. Time to flower was positively correlated with flower bud number in the P. x hybrida 'Mitchell' x P. axillaris and P. axillaris x P. integrifolia families only. Based on these results, wild Petunia germplasm should be useful for developing petunia cultivars with reduced crop production times, but some negative effects on crop quality parameters may need to be overcome.

Emergency medical services as a strategy for improving ST-elevation myocardial infarction system treatment times.

PubMed

Langabeer, James R; Dellifraine, Jami; Fowler, Raymond; Jollis, James G; Stuart, Leilani; Segrest, Wendy; Griffin, Russell; Koenig, William; Moyer, Peter; Henry, Timothy D

2014-03-01

Reducing delays in time to treatment is a key goal of ST-elevation myocardial infarction (STEMI) emergency care. Emergency medical services (EMS) are a critical component of the STEMI chain of survival. We sought to assess the impact of the careful integration of EMS as a strategy for improving systemic treatment times for STEMI. We conducted a study of all 747 nontransfer STEMI patients who underwent primary percutaneous coronary intervention (PCI) in Dallas County, Texas from October 1, 2010 through December 31, 2011. EMS leaders from 24 agencies and 15 major PCI receiving hospitals collected and shared common, de-identified patient data. We used 15 months of data to develop a generalized linear regression to assess the impact of EMS on two treatment metrics-hospital door to balloon (D2B) time, and symptom onset to arterial reperfusion (SOAR) time, a new metric we developed to assess total treatment times. We found statistically significant reductions in median D2B (11.1-min reduction) and SOAR (63.5-min reduction) treatment times when EMS transported patients to the receiving facility, compared to self-transport. In addition, when trained EMS paramedics field-activated the cardiac catheterization laboratory using predefined specified protocols, D2B times were reduced by 38% (43 min) after controlling for confounding variables, and field activation was associated with a 21.9% reduction (73 min) in the mean SOAR time (both with p < 0.001). Active EMS engagement in STEMI treatment was associated with significantly lower D2B and total coronary reperfusion times. Copyright © 2014 Elsevier Inc. All rights reserved.

Development of a decentralized multi-axis synchronous control approach for real-time networks.

PubMed

Xu, Xiong; Gu, Guo-Ying; Xiong, Zhenhua; Sheng, Xinjun; Zhu, Xiangyang

2017-05-01

The message scheduling and the network-induced delays of real-time networks, together with the different inertias and disturbances in different axes, make the synchronous control of the real-time network-based systems quite challenging. To address this challenge, a decentralized multi-axis synchronous control approach is developed in this paper. Due to the limitations of message scheduling and network bandwidth, error of the position synchronization is firstly defined in the proposed control approach as a subset of preceding-axis pairs. Then, a motion message estimator is designed to reduce the effect of network delays. It is proven that position and synchronization errors asymptotically converge to zero in the proposed controller with the delay compensation. Finally, simulation and experimental results show that the developed control approach can achieve the good position synchronization performance for the multi-axis motion over the real-time network. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

Reducing Risks to Women Linked to Shift Work, Long Work Hours, and Related Workplace Sleep and Fatigue Issues.

PubMed

Caruso, Claire C

2015-10-01

In the United States, an estimated 12% to 28% of working women are on shift work schedules, and 12% work more than 48 hours per week. Shift work and long work hours are associated with many health and safety risks, including obesity, injuries, and negative reproductive outcomes. Over time, the worker is at risk for developing a wide range of chronic diseases. These work schedules can also strain personal relationships, owing to fatigue and poor mood from sleep deprivation and reduced quality time to spend with family and friends. Worker errors from fatigue can lead to reduced quality of goods and services, negatively impacting the employer. In addition, mistakes by fatigued workers can have far-reaching negative effects on the community, ranging from medical care errors to motor vehicle crashes and industrial disasters that endanger others. To reduce the many risks that are linked to these demanding work hours, the National Institute for Occupational Safety and Health (NIOSH) conducts research, develops guidance and authoritative recommendations, and translates and disseminates scientific information to protect workers, their families, employers, and the community. The key message to reduce these risks is making sleep a priority in the employer's systems for organizing work and in the worker's personal life. The NIOSH website has freely available online training programs with suggestions for workers and their managers to help them better cope with this workplace hazard.

Next Generation Polar Seismic Instrumentation Challenges

NASA Astrophysics Data System (ADS)

Parker, T.; Beaudoin, B. C.; Gridley, J.; Anderson, K. R.

2011-12-01

Polar region logistics are the limiting factor for deploying deep field seismic arrays. The IRIS PASSCAL Instrument Center, in collaboration with UNAVCO, designed and deployed several systems that address some of the logistical constraints of polar deployments. However, continued logistics' pressures coupled with increasingly ambitious science projects require further reducing the logistics required for deploying both summer and over winter stations. Our focus is to reduce station power requirements and bulk, thereby minimizing the time and effort required to deploy these arrays. We will reduce the weight of the battery bank by incorporating the most applicable new high energy-density battery technology. Using these batteries will require a completely new power management system along with an appropriate smart enclosure. The other aspect will be to integrate the digitizing system with the sensor. Both of these technologies should reduce the install time and shipping volume plus weight while reducing some instrument costs. We will also continue work on an effective Iridium telemetry solution for automated data return. The costs and limitations of polar deep-field science easily justifies a specialized development effort but pays off doubly in that we will continue to leverage the advancements in reduced logistics and increased performance for the benefit of low-latitude seismic research.

Excitation Light Dose Engineering to Reduce Photo-bleaching and Photo-toxicity

PubMed Central

Boudreau, Colton; Wee, Tse-Luen (Erika); Duh, Yan-Rung (Silvia); Couto, Melissa P.; Ardakani, Kimya H.; Brown, Claire M.

2016-01-01

It is important to determine the most effective method of delivering light onto a specimen for minimal light induced damage. Assays are presented to measure photo-bleaching of fluorophores and photo-toxicity to living cells under different illumination conditions. Turning the light off during part of the experimental time reduced photo-bleaching in a manner proportional to the time of light exposure. The rate of photo-bleaching of EGFP was reduced by 9-fold with light pulsing on the micro-second scale. Similarly, in living cells, rapid line scanning resulted in reduced cell stress as measured by mitochondrial potential, rapid cell protrusion and reduced cell retraction. This was achieved on a commercial confocal laser scanning microscope, without any compromise in image quality, by using rapid laser scan settings and line averaging. Therefore this technique can be implemented broadly without any software or hardware upgrades. Researchers can use the rapid line scanning option to immediately improve image quality on fixed samples, reduce photo-bleaching for large high resolution 3D datasets and improve cell health in live cell experiments. The assays developed here can be applied to other microscopy platforms to measure and optimize light delivery for minimal sample damage and photo-toxicity. PMID:27485088

Excitation Light Dose Engineering to Reduce Photo-bleaching and Photo-toxicity.

PubMed

Boudreau, Colton; Wee, Tse-Luen Erika; Duh, Yan-Rung Silvia; Couto, Melissa P; Ardakani, Kimya H; Brown, Claire M

2016-08-03

It is important to determine the most effective method of delivering light onto a specimen for minimal light induced damage. Assays are presented to measure photo-bleaching of fluorophores and photo-toxicity to living cells under different illumination conditions. Turning the light off during part of the experimental time reduced photo-bleaching in a manner proportional to the time of light exposure. The rate of photo-bleaching of EGFP was reduced by 9-fold with light pulsing on the micro-second scale. Similarly, in living cells, rapid line scanning resulted in reduced cell stress as measured by mitochondrial potential, rapid cell protrusion and reduced cell retraction. This was achieved on a commercial confocal laser scanning microscope, without any compromise in image quality, by using rapid laser scan settings and line averaging. Therefore this technique can be implemented broadly without any software or hardware upgrades. Researchers can use the rapid line scanning option to immediately improve image quality on fixed samples, reduce photo-bleaching for large high resolution 3D datasets and improve cell health in live cell experiments. The assays developed here can be applied to other microscopy platforms to measure and optimize light delivery for minimal sample damage and photo-toxicity.

Development of the oriental latrine fly, Chrysomya megacephala (Diptera: Calliphoridae), at five constant temperatures

USGS Publications Warehouse

Gruner, S. V.; Slone, D.H.; Capinera, J.L.; Turco, M. P.

2017-01-01

Chrysomya megacephala (Fabricius) is a forensically important fly that is found throughout the tropics and subtropics. We calculated the accumulated development time and transition points for each life stage from eclosion to adult emergence at five constant temperatures: 15, 20, 25, 30, and 35 °C. For each transition, the 10th, 50th, and 90th percentiles were calculated with a logistic linear model. The mean transition times and % survivorship were determined directly from the raw laboratory data. Development times of C. megacephala were compared with that of two other closely related species, Chrysomya rufifacies (Macquart) and Phormia regina (Meigen). Ambient and larval mass temperatures were collected from field studies conducted from 2001–2004. Field study data indicated that adult fly activity was reduced at lower ambient temperatures, but once a larval mass was established, heat generation occurred. These development times and durations can be used for estimation of a postmortem interval (PMI).

NHE inhibition does not improve Na(+) or Ca(2+) overload during reperfusion: using modeling to illuminate the mechanisms underlying a therapeutic failure.

PubMed

Roberts, Byron N; Christini, David J

2011-10-01

Reperfusion injury results from pathologies of cardiac myocyte physiology that develop when previously ischemic myocardium experiences a restoration of normal perfusion. Events in the development of reperfusion injury begin with the restoration of a proton gradient upon reperfusion, which then allows the sodium-proton exchanger (NHE) to increase flux, removing protons from the intracellular space while importing sodium. The resulting sodium overload drives increased reverse-mode sodium-calcium exchanger (NCX) activity, creating a secondary calcium overload that has pathologic consequences. One of the attempts to reduce reperfusion-related damage, NHE inhibition, has shown little clinical benefit, and only when NHE inhibitors are given prior to reperfusion. In an effort to further understand why NHE inhibitors have been largely unsuccessful, we employed a new mathematical cardiomyocyte model that we developed for the study of ischemia and reperfusion. Using this model, we simulated 20 minutes of ischemia and 10 minutes of reperfusion, while also simulating NHE inhibition by reducing NHE flux in our model by varying amounts and at different time points. In our simulations, when NHE inhibition is applied at the onset of reperfusion, increasing the degree of inhibition increases the peak sodium and calcium concentrations, as well as reducing intracellular pH recovery. When inhibition was instituted at earlier time points, some modest improvements were seen, largely due to reduced sodium concentrations prior to reperfusion. Analysis of all sodium flux pathways suggests that the sodium-potassium pump (NaK) plays the largest role in exacerbated sodium overload during reperfusion, and that reduced NaK flux is largely the result of impaired pH recovery. While NHE inhibition does indeed reduce sodium influx through that exchanger, the resulting prolongation of intracellular acidosis paradoxically increases sodium overload, largely mediated by impaired NaK function.

NHE Inhibition Does Not Improve Na+ or Ca2+ Overload During Reperfusion: Using Modeling to Illuminate the Mechanisms Underlying a Therapeutic Failure

PubMed Central

Roberts, Byron N.; Christini, David J.

2011-01-01

Reperfusion injury results from pathologies of cardiac myocyte physiology that develop when previously ischemic myocardium experiences a restoration of normal perfusion. Events in the development of reperfusion injury begin with the restoration of a proton gradient upon reperfusion, which then allows the sodium-proton exchanger (NHE) to increase flux, removing protons from the intracellular space while importing sodium. The resulting sodium overload drives increased reverse-mode sodium-calcium exchanger (NCX) activity, creating a secondary calcium overload that has pathologic consequences. One of the attempts to reduce reperfusion-related damage, NHE inhibition, has shown little clinical benefit, and only when NHE inhibitors are given prior to reperfusion. In an effort to further understand why NHE inhibitors have been largely unsuccessful, we employed a new mathematical cardiomyocyte model that we developed for the study of ischemia and reperfusion. Using this model, we simulated 20 minutes of ischemia and 10 minutes of reperfusion, while also simulating NHE inhibition by reducing NHE flux in our model by varying amounts and at different time points. In our simulations, when NHE inhibition is applied at the onset of reperfusion, increasing the degree of inhibition increases the peak sodium and calcium concentrations, as well as reducing intracellular pH recovery. When inhibition was instituted at earlier time points, some modest improvements were seen, largely due to reduced sodium concentrations prior to reperfusion. Analysis of all sodium flux pathways suggests that the sodium-potassium pump (NaK) plays the largest role in exacerbated sodium overload during reperfusion, and that reduced NaK flux is largely the result of impaired pH recovery. While NHE inhibition does indeed reduce sodium influx through that exchanger, the resulting prolongation of intracellular acidosis paradoxically increases sodium overload, largely mediated by impaired NaK function. PMID:22028644

Recent Cycle Time Reduction at Langley Research Center

NASA Technical Reports Server (NTRS)

Kegelman, Jerome T.

2000-01-01

The NASA Langley Research Center (LaRC) has been engaged in an effort to reduce wind tunnel test cycle time in support of Agency goals and to satisfy the wind tunnel testing needs of the commercial and military aerospace communities. LaRC has established the Wind Tunnel Enterprise (WTE), with goals of reducing wind tunnel test cycle time by an order of magnitude by 2002, and by two orders of magnitude by 2010. The WTE also plans to meet customer expectations for schedule integrity, as well as data accuracy and quality assurance. The WTE has made progress towards these goals over the last year with a focused effort on technological developments balanced by attention to process improvements. This paper presents a summary of several of the WTE activities over the last year that are related to test cycle time reductions at the Center. Reducing wind tunnel test cycle time, defined here as the time between the freezing of loft lines and delivery of test data, requires that the relationship between high productivity and data quality assurance be considered. The efforts have focused on all of the drivers for test cycle time reduction, including process centered improvements, facility upgrades, technological improvements to enhance facility readiness and productivity, as well as advanced measurement techniques. The application of internet tools and computer modeling of facilities to allow a virtual presence of the customer team is also presented.

H2 arcjet performance mapping program

NASA Astrophysics Data System (ADS)

1992-01-01

Work performed during the period of Mar. 1991 to Jan. 1992 is reviewed. High power H2 arcjets are being considered for electric powered orbit transfer vehicles (EOTV). Mission analyses indicate that the overall arcjet thrust efficiency is very important since increasing the efficiency increases the thrust, and thereby reduces the total trip time for the same power. For example, increasing the thrust efficiency at the same specific impulse from 30 to 40 percent will reduce the trip time by 25 percent. For a 200 day mission, this equates to 50 days, which results in lower ground costs and less time during which the payload is dormant. Arcjet performance levels of 1200 seconds specific impulse (lsp) at 35 to 40 percent efficiency with lifetimes over 1000 hours are needed to support EOTV missions. Because of the potential very high efficiency levels, the objective of this program was to evaluate the ability of a scaled Giannini-style thruster to achieve the performance levels while operating at a reduced nominal power of 10 kW. To meet this objective, a review of past literature was conducted; scaling relationships were developed and applied to establish critical dimensions; a development thruster was designed with the aid of the plasma analysis model KARNAC and finite element thermal modeling; test hardware was fabricated; and a series of performance tests were conducted in RRC's Cell 11 vacuum chamber with its null-balance thrust stand.

Involving service users in intervention design: a participatory approach to developing a text-messaging intervention to reduce repetition of self-harm.

PubMed

Owens, Christabel; Farrand, Paul; Darvill, Ruth; Emmens, Tobit; Hewis, Elaine; Aitken, Peter

2011-09-01

OBJECTIVE To engage a group of people with relevant lived experience in the development of a text-messaging intervention to reduce repetition of self-harm. BACKGROUND Contact-based interventions, such as follow-up letters, postcards and telephone calls, have shown potential to reduce repetition of self-harm in those who present at Accident and Emergency departments. Text messaging offers a low-cost alternative that has not been tested. We set out to develop a text-based intervention. The process of intervention development is rarely reported and little is known about the impact of service user involvement on intervention design. METHOD We held a series of six participatory workshops and invited service users and clinicians to help us work out how to get the right message to the right person at the right time, and to simulate and test prototypes of an intervention. RESULTS Service users rejected both the idea of a generic, 'one size fits all' approach and that of 'audience segmentation', maintaining that text messages could be safe and effective only if individualized. This led us to abandon our original thinking and develop a way of supporting individuals to author their own self-efficacy messages and store them in a personal message bank for withdrawal at times of crisis. CONCLUSIONS This paper highlights both the challenge and the impact of involving consumers at the development stage. Working with those with lived experience requires openness, flexibility and a readiness to abandon or radically revise initial plans, and may have unexpected consequences for intervention design. © 2010 Blackwell Publishing Ltd.

Involving service users in intervention design: a participatory approach to developing a text‐messaging intervention to reduce repetition of self‐harm

PubMed Central

Owens, Christabel; Farrand, Paul; Darvill, Ruth; Emmens, Tobit; Hewis, Elaine; Aitken, Peter

2010-01-01

Abstract Objective  To engage a group of people with relevant lived experience in the development of a text‐messaging intervention to reduce repetition of self‐harm. Background  Contact‐based interventions, such as follow‐up letters, postcards and telephone calls, have shown potential to reduce repetition of self‐harm in those who present at Accident and Emergency departments. Text messaging offers a low‐cost alternative that has not been tested. We set out to develop a text‐based intervention. The process of intervention development is rarely reported and little is known about the impact of service user involvement on intervention design. Method  We held a series of six participatory workshops and invited service users and clinicians to help us work out how to get the right message to the right person at the right time, and to simulate and test prototypes of an intervention. Results  Service users rejected both the idea of a generic, ‘one size fits all’ approach and that of ‘audience segmentation’, maintaining that text messages could be safe and effective only if individualized. This led us to abandon our original thinking and develop a way of supporting individuals to author their own self‐efficacy messages and store them in a personal message bank for withdrawal at times of crisis. Conclusions  This paper highlights both the challenge and the impact of involving consumers at the development stage. Working with those with lived experience requires openness, flexibility and a readiness to abandon or radically revise initial plans, and may have unexpected consequences for intervention design. PMID:20860777

Multishaker modal testing

NASA Technical Reports Server (NTRS)

Craig, Roy R., Jr.

1987-01-01

The major accomplishments of this research are: (1) the refinement and documentation of a multi-input, multi-output modal parameter estimation algorithm which is applicable to general linear, time-invariant dynamic systems; (2) the development and testing of an unsymmetric block-Lanzcos algorithm for reduced-order modeling of linear systems with arbitrary damping; and (3) the development of a control-structure-interaction (CSI) test facility.

Rangeland livestock production: Developing the concept of sustainability on the Santa Rita Experimental Range

Treesearch

George B. Ruyle

2003-01-01

The Santa Rita Experimental Range (SRER) was established in 1903 at the behest of concerned stockmen and researchers as the first facility in the United States set aside to study range livestock production. At the time, severe overgrazing of the public domain had seriously reduced carrying capacities of Southwestern rangelands. Researchers on the SRER developed and...

Quasi steady-state aerodynamic model development for race vehicle simulations

NASA Astrophysics Data System (ADS)

Mohrfeld-Halterman, J. A.; Uddin, M.

2016-01-01

Presented in this paper is a procedure to develop a high fidelity quasi steady-state aerodynamic model for use in race car vehicle dynamic simulations. Developed to fit quasi steady-state wind tunnel data, the aerodynamic model is regressed against three independent variables: front ground clearance, rear ride height, and yaw angle. An initial dual range model is presented and then further refined to reduce the model complexity while maintaining a high level of predictive accuracy. The model complexity reduction decreases the required amount of wind tunnel data thereby reducing wind tunnel testing time and cost. The quasi steady-state aerodynamic model for the pitch moment degree of freedom is systematically developed in this paper. This same procedure can be extended to the other five aerodynamic degrees of freedom to develop a complete six degree of freedom quasi steady-state aerodynamic model for any vehicle.

A Reliability-Based Particle Filter for Humanoid Robot Self-Localization in RoboCup Standard Platform League

PubMed Central

Sánchez, Eduardo Munera; Alcobendas, Manuel Muñoz; Noguera, Juan Fco. Blanes; Gilabert, Ginés Benet; Simó Ten, José E.

2013-01-01

This paper deals with the problem of humanoid robot localization and proposes a new method for position estimation that has been developed for the RoboCup Standard Platform League environment. Firstly, a complete vision system has been implemented in the Nao robot platform that enables the detection of relevant field markers. The detection of field markers provides some estimation of distances for the current robot position. To reduce errors in these distance measurements, extrinsic and intrinsic camera calibration procedures have been developed and described. To validate the localization algorithm, experiments covering many of the typical situations that arise during RoboCup games have been developed: ranging from degradation in position estimation to total loss of position (due to falls, ‘kidnapped robot’, or penalization). The self-localization method developed is based on the classical particle filter algorithm. The main contribution of this work is a new particle selection strategy. Our approach reduces the CPU computing time required for each iteration and so eases the limited resource availability problem that is common in robot platforms such as Nao. The experimental results show the quality of the new algorithm in terms of localization and CPU time consumption. PMID:24193098

[State of the art and future trends in technology for computed tomography dose reduction].

PubMed

Calzado Cantera, A; Hernández-Girón, I; Salvadó Artells, M; Rodríguez González, R

2013-12-01

The introduction of helical and multislice acquisitions in CT scanners together with decreased image reconstruction times has had a tremendous impact on radiological practice. Technological developments in the last 10 to 12 years have enabled very high quality images to be obtained in a very short time. Improved image quality has led to an increase in the number of indications for CT. In parallel to this development, radiation exposure in patients has increased considerably. Concern about the potential health risks posed by CT imaging, reflected in diverse initiatives and actions by official organs and scientific societies, has prompted the search for ways to reduce radiation exposure in patients without compromising diagnostic efficacy. To this end, good practice guidelines have been established, special applications have been developed for scanners, and research has been undertaken to optimize the clinical use of CT. Noteworthy technical developments incorporated in scanners include the different modes of X-ray tube current modulation, automatic selection of voltage settings, selective organ protection, adaptive collimation, and iterative reconstruction. The appropriate use of these tools to reduce radiation doses requires thorough knowledge of how they work. Copyright © 2013 SERAM. Published by Elsevier Espana. All rights reserved.

Sublethal Effects of Insecticide Exposure on Megacopta cribraria (Fabricius) Nymphs: Key Biological Traits and Acetylcholinesterase Activity.

PubMed

Miao, Jin; Reisig, Dominic D; Li, Guoping; Wu, Yuqing

2016-01-01

Megacopta cribraria F. (Hemiptera: Plataspidae), the kudzu bug, is an invasive insect pest of U.S. soybean. At present, insecticide application is the primary and most effective control option for M. cribraria In this study, the potential effects of sublethal and low-lethal concentrations (LC10 and LC40) of three common insecticides on key biological traits and acetylcholinesterase (AChE) activity of the treated nymphal stage of insect were assessed. The results show that the sublethal concentration of imidacloprid significantly reduced adult emergence rate of M. cribraria A low-lethal concentration of imidacloprid significantly increased nymphal development time, but significantly decreased adult emergence rate and adult longevity. Both sublethal and low-lethal concentrations of acephate caused an increase in nymphal development time and a reduction in adult emergence rate and adult longevity. Fecundity of females was significantly reduced only by exposure to low-lethal concentrations of acephate. Sublethal and low-lethal concentrations of bifenthrin increased nymphal development time, but significantly decreased adult emergence rate. In addition, we found that the AChE activity of M. cribraria was significantly increased only by LC40 imidacloprid, but strongly inhibited by acephate. © The Author 2016. Published by Oxford University Press on behalf of the Entomological Society of America.

New and developing diagnostic technologies for urinary tract infections

PubMed Central

Davenport, Michael; Mach, Kathleen E.; Dairiki Shortliffe, Linda M.; Banaei, Niaz; Wang, Tza-Huei; Liao, Joseph C.

2017-01-01

Timely and accurate identification and determination of the antimicrobial susceptibility of uropathogens is central to the management of UTIs. Urine dipsticks are fast and amenable to point-of-care testing, but do not have adequate diagnostic accuracy or provide microbiological diagnosis. Urine culture with antimicrobial susceptibility testing takes 2 3 days and requires a clinical laboratory. The common use of empirical antibiotics has contributed to the rise of multidrug-resistant organisms, reducing treatment options and increasing costs. In addition to improved antimicrobial stewardship and the development of new antimicrobials, novel diagnostics are needed for timely microbial identification and determination of antimicrobial susceptibilities. New diagnostic platforms, including nucleic acid tests and mass spectrometry, have been approved for clinical use and have improved the speed and accuracy of pathogen identification from primary cultures. Optimization for direct urine testing would reduce the time to diagnosis, yet these technologies do not provide comprehensive information on antimicrobial susceptibility. Emerging technologies including biosensors, microfluidics, and other integrated platforms could improve UTI diagnosis via direct pathogen detection from urine samples, rapid antimicrobial susceptibility testing, and point-of-care testing. Successful development and implementation of these technologies has the potential to usher in an era of precision medicine to improve patient care and public health. PMID:28248946

MASC: Multiprocessor Architecture for Symbolic Processing

DTIC Science & Technology

1989-08-01

accomplish the ultimate goal of reducing the time to develop the 5- 12 correct parse. 5.6.5 Effect of’ Sentence Length Figure 5-6 shows the relationship...later; this effectively restricts the breadth of study rather severely. 6.1.2. Objective The tools described here have been developed in response to...either expressed or implied, of the Defense Advanced Research Projects Agency or the U.S. Government. ROME AIR DEVELOPMENT CENTER Air Force Systems

AnimalFinder: A semi-automated system for animal detection in time-lapse camera trap images

USGS Publications Warehouse

Price Tack, Jennifer L.; West, Brian S.; McGowan, Conor P.; Ditchkoff, Stephen S.; Reeves, Stanley J.; Keever, Allison; Grand, James B.

2017-01-01

Although the use of camera traps in wildlife management is well established, technologies to automate image processing have been much slower in development, despite their potential to drastically reduce personnel time and cost required to review photos. We developed AnimalFinder in MATLAB® to identify animal presence in time-lapse camera trap images by comparing individual photos to all images contained within the subset of images (i.e. photos from the same survey and site), with some manual processing required to remove false positives and collect other relevant data (species, sex, etc.). We tested AnimalFinder on a set of camera trap images and compared the presence/absence results with manual-only review with white-tailed deer (Odocoileus virginianus), wild pigs (Sus scrofa), and raccoons (Procyon lotor). We compared abundance estimates, model rankings, and coefficient estimates of detection and abundance for white-tailed deer using N-mixture models. AnimalFinder performance varied depending on a threshold value that affects program sensitivity to frequently occurring pixels in a series of images. Higher threshold values led to fewer false negatives (missed deer images) but increased manual processing time, but even at the highest threshold value, the program reduced the images requiring manual review by ~40% and correctly identified >90% of deer, raccoon, and wild pig images. Estimates of white-tailed deer were similar between AnimalFinder and the manual-only method (~1–2 deer difference, depending on the model), as were model rankings and coefficient estimates. Our results show that the program significantly reduced data processing time and may increase efficiency of camera trapping surveys.

Non-Preemptive Time Warp Scheduling Algorithms

DTIC Science & Technology

1990-06-01

conducted in the Applied Technology Program of the Arroyo Center. Questions involving technical issues should be addressed to Dr. ,Jed Marti. Project...emphasizing mid- to long- terin problents. Its research is carried out in five programs : Policy and Strategy Studies: Force Development and Employment...various system parameters to reduce the global program execution time. Because we wanted to scale the system up, we did not allow interprocessor

Turbine Design to Mitigate Forcing (POSTPRINT)

DTIC Science & Technology

2012-09-01

durability enhancements, sometimes fuel nozzles and turbine nozzle guide vanes are also clocked in an effort to reduce the heat load to downstream...e.g., aero- performance or heat load) or to estimate resonant stresses on the airfoils. So, the development of both time-mean and time-resolved...disturbances. So, great flexibility was built into the current implementation of the convergence-assessment algorithm described above. The user can

A Report on Army Science Planning and Strategy 2016

DTIC Science & Technology

2017-06-01

Army Research Laboratory (ARL) hosted a series of meetings in fall 2016 to develop a strategic vision for Army Science. Meeting topics were vetted...reduce maturation time . • Support internal Army research efforts to enhance Army investments in multiscale modeling to accelerate the rate of...requirement are research needs including cross-modal approaches to enabling real- time human comprehension under constraints of bandwidth, information

New algorithms for processing time-series big EEG data within mobile health monitoring systems.

PubMed

Serhani, Mohamed Adel; Menshawy, Mohamed El; Benharref, Abdelghani; Harous, Saad; Navaz, Alramzana Nujum

2017-10-01

Recent advances in miniature biomedical sensors, mobile smartphones, wireless communications, and distributed computing technologies provide promising techniques for developing mobile health systems. Such systems are capable of monitoring epileptic seizures reliably, which are classified as chronic diseases. Three challenging issues raised in this context with regard to the transformation, compression, storage, and visualization of big data, which results from a continuous recording of epileptic seizures using mobile devices. In this paper, we address the above challenges by developing three new algorithms to process and analyze big electroencephalography data in a rigorous and efficient manner. The first algorithm is responsible for transforming the standard European Data Format (EDF) into the standard JavaScript Object Notation (JSON) and compressing the transformed JSON data to decrease the size and time through the transfer process and to increase the network transfer rate. The second algorithm focuses on collecting and storing the compressed files generated by the transformation and compression algorithm. The collection process is performed with respect to the on-the-fly technique after decompressing files. The third algorithm provides relevant real-time interaction with signal data by prospective users. It particularly features the following capabilities: visualization of single or multiple signal channels on a smartphone device and query data segments. We tested and evaluated the effectiveness of our approach through a software architecture model implementing a mobile health system to monitor epileptic seizures. The experimental findings from 45 experiments are promising and efficiently satisfy the approach's objectives in a price of linearity. Moreover, the size of compressed JSON files and transfer times are reduced by 10% and 20%, respectively, while the average total time is remarkably reduced by 67% through all performed experiments. Our approach successfully develops efficient algorithms in terms of processing time, memory usage, and energy consumption while maintaining a high scalability of the proposed solution. Our approach efficiently supports data partitioning and parallelism relying on the MapReduce platform, which can help in monitoring and automatic detection of epileptic seizures. Copyright © 2017 Elsevier B.V. All rights reserved.

New cardiac cameras: single-photon emission CT and PET.

PubMed

Slomka, Piotr J; Berman, Daniel S; Germano, Guido

2014-07-01

Nuclear cardiology instrumentation has evolved significantly in the recent years. Concerns about radiation dose and long acquisition times have propelled developments of dedicated high-efficiency cardiac SPECT scanners. Novel collimator designs, such as multipinhole or locally focusing collimators arranged in geometries that are optimized for cardiac imaging, have been implemented to enhance photon-detection sensitivity. Some of these new SPECT scanners use solid-state photon detectors instead of photomultipliers to improve image quality and to reduce the scanner footprint. These new SPECT devices allow dramatic up to 7-fold reduction in acquisition times or similar reduction in radiation dose. In addition, new hardware for photon attenuation correction allowing ultralow radiation doses has been offered by some vendors. To mitigate photon attenuation artifacts for the new SPECT scanners not equipped with attenuation correction hardware, 2-position (upright-supine or prone-supine) imaging has been proposed. PET hardware developments have been primarily driven by the requirements of oncologic imaging, but cardiac imaging can benefit from improved PET image quality and improved sensitivity of 3D systems. The time-of-flight reconstruction combined with resolution recovery techniques is now implemented by all major PET vendors. These new methods improve image contrast and image resolution and reduce image noise. High-sensitivity 3D PET without interplane septa allows reduced radiation dose for cardiac perfusion imaging. Simultaneous PET/MR hybrid system has been developed. Solid-state PET detectors with avalanche photodiodes or digital silicon photomultipliers have been introduced, and they offer improved imaging characteristics and reduced sensitivity to electromagnetic MR fields. Higher maximum count rate of the new PET detectors allows routine first-pass Rb-82 imaging, with 3D PET acquisition enabling clinical utilization of dynamic imaging with myocardial flow measurements for this tracer. The availability of high-end CT component in most PET/CT configurations enables hybrid multimodality cardiac imaging protocols with calcium scoring or CT angiography or both. Copyright © 2014. Published by Elsevier Inc.

Reducing Development and Operations Costs using NASA's "GMSEC" Systems Architecture

NASA Technical Reports Server (NTRS)

Smith, Dan; Bristow, John; Crouse, Patrick

2007-01-01

This viewgraph presentation reviews the role of Goddard Mission Services Evolution Center (GMSEC) in reducing development and operation costs in handling the massive data from NASA missions. The goals of GMSEC systems architecture development are to (1) Simplify integration and development, (2)Facilitate technology infusion over time, (3) Support evolving operational concepts, and (4) All for mix of heritage, COTS and new components. First 3 missions (i.e., Tropical Rainforest Measuring Mission (TRMM), Small Explorer (SMEX) missions - SWAS, TRACE, SAMPEX, and ST5 3-Satellite Constellation System) each selected a different telemetry and command system. These results show that GMSEC's message-bus component-based framework architecture is well proven and provides significant benefits over traditional flight and ground data system designs. The missions benefit through increased set of product options, enhanced automation, lower cost and new mission-enabling operations concept options .

Effects of the juvenile hormone analogue methoprene on rate of behavioural development, foraging performance and navigation in honey bees (Apis mellifera).

PubMed

Chang, Lun-Hsien; Barron, Andrew B; Cheng, Ken

2015-06-01

Worker honey bees change roles as they age as part of a hormonally regulated process of behavioural development that ends with a specialised foraging phase. The rate of behavioural development is highly plastic and responsive to changes in colony condition such that forager losses, disease or nutritional stresses accelerate behavioural development and cause an early onset of foraging in workers. It is not clear to what degree the behavioural development of workers can be accelerated without there being a cost in terms of reduced foraging performance. Here, we compared the foraging performance of bees induced to accelerate their behavioural development by treatment with the juvenile hormone analogue methoprene with that of controls that developed at a normal rate. Methoprene treatment accelerated the onset of both flight and foraging behaviour in workers, but it also reduced foraging span, the total time spent foraging and the number of completed foraging trips. Methoprene treatment did not alter performance in a short-range navigation task, however. These data indicate a limitation to the physiological plasticity of bees, and a trade off between forager performance and the speed at which bees begin foraging. Chronic stressors will be expected to reduce the mean age of the foraging force, and therefore also reduce the efficiency of the foraging force. This interaction may explain why honey bee colonies react to sustained stressors with non-linear population decline. © 2015. Published by The Company of Biologists Ltd.

Honeybee Colony Vibrational Measurements to Highlight the Brood Cycle

PubMed Central

Bencsik, Martin; Le Conte, Yves; Reyes, Maritza; Pioz, Maryline; Whittaker, David; Crauser, Didier; Simon Delso, Noa; Newton, Michael I.

2015-01-01

Insect pollination is of great importance to crop production worldwide and honey bees are amongst its chief facilitators. Because of the decline of managed colonies, the use of sensor technology is growing in popularity and it is of interest to develop new methods which can more accurately and less invasively assess honey bee colony status. Our approach is to use accelerometers to measure vibrations in order to provide information on colony activity and development. The accelerometers provide amplitude and frequency information which is recorded every three minutes and analysed for night time only. Vibrational data were validated by comparison to visual inspection data, particularly the brood development. We show a strong correlation between vibrational amplitude data and the brood cycle in the vicinity of the sensor. We have further explored the minimum data that is required, when frequency information is also included, to accurately predict the current point in the brood cycle. Such a technique should enable beekeepers to reduce the frequency with which visual inspections are required, reducing the stress this places on the colony and saving the beekeeper time. PMID:26580393

Forecast Based Financing for Managing Weather and Climate Risks to Reduce Potential Disaster Impacts

NASA Astrophysics Data System (ADS)

Arrighi, J.

2017-12-01

There is a critical window of time to reduce potential impacts of a disaster after a forecast for heightened risk is issued and before an extreme event occurs. The concept of Forecast-based Financing focuses on this window of opportunity. Through advanced preparation during system set-up, tailored methodologies are used to 1) analyze a range of potential extreme event forecasts, 2) identify emergency preparedness measures that can be taken when factoring in forecast lead time and inherent uncertainty and 3) develop standard operating procedures that are agreed on and tied to guaranteed funding sources to facilitate emergency measures led by the Red Cross or government actors when preparedness measures are triggered. This presentation will focus on a broad overview of the current state of theory and approaches used in developing a forecast-based financing systems - with a specific focus on hydrologic events, case studies of success and challenges in various contexts where this approach is being piloted, as well as what is on the horizon to be further explored and developed from a research perspective as the application of this approach continues to expand.

NASA Aircraft Vortex Spacing System Development Status

NASA Technical Reports Server (NTRS)

Hinton, David A.; Charnock, James K.; Bagwell, Donald R.; Grigsby, Donner

1999-01-01

The National Aeronautics and Space Administration (NASA) is addressing airport capacity enhancements during instrument meteorological conditions through the Terminal Area Productivity (TAP) program. Within TAP, the Reduced Spacing Operations (RSO) subelement at the NASA Langley Research Center is developing an Aircraft VOrtex Spacing System (AVOSS). AVOSS will integrate the output of several systems to produce weather dependent, dynamic wake vortex spacing criteria. These systems provide current and predicted weather conditions, models of wake vortex transport and decay in these weather conditions, and real-time feedback of wake vortex behavior from sensors. The goal of the NASA program is to provide the research and development to demonstrate an engineering model AVOSS in real-time operation at a major airport. The demonstration is only of concept feasibility, and additional effort is required to deploy an operational system for actual aircraft spacing reduction. This paper describes the AVOSS system architecture, a wake vortex facility established at the Dallas-Fort Worth International Airport (DFW), initial operational experience with the AVOSS system, and emerging considerations for subsystem requirements. Results of the initial system operation suggest a significant potential for reduced spacing.

Alternative nuclear technologies

NASA Astrophysics Data System (ADS)

Schubert, E.

1981-10-01

The lead times required to develop a select group of nuclear fission reactor types and fuel cycles to the point of readiness for full commercialization are compared. Along with lead times, fuel material requirements and comparative costs of producing electric power were estimated. A conservative approach and consistent criteria for all systems were used in estimates of the steps required and the times involved in developing each technology. The impact of the inevitable exhaustion of the low- or reasonable-cost uranium reserves in the United States on the desirability of completing the breeder reactor program, with its favorable long-term result on fission fuel supplies, is discussed. The long times projected to bring the most advanced alternative converter reactor technologies the heavy water reactor and the high-temperature gas-cooled reactor into commercial deployment when compared to the time projected to bring the breeder reactor into equivalent status suggest that the country's best choice is to develop the breeder. The perceived diversion-proliferation problems with the uranium plutonium fuel cycle have workable solutions that can be developed which will enable the use of those materials at substantially reduced levels of diversion risk.

Cost as a technology driver. [in aerospace R and D

NASA Technical Reports Server (NTRS)

Fitzgerald, P. E., Jr.; Savage, M.

1976-01-01

Cost managment as a guiding factor in optimum development of technology, and proper timing of cost-saving programs in the development of a system or technology with payoffs in development and operational advances are discussed and illustrated. Advances enhancing the performance of hardware or software advances raising productivity or reducing cost, are outlined, with examples drawn from: thermochemical thrust maximization, development of cryogenic storage tanks, improvements in fuel cells for Space Shuttle, design of a spacecraft pyrotechnic initiator, cost cutting by reduction in the number of parts to be joined, and cost cutting by dramatic reductions in circuit component number with small-scale double-diffused integrated circuitry. Program-focused supporting research and technology models are devised to aid judicious timing of cost-conscious research programs.

Workstation-Based Simulation for Rapid Prototyping and Piloted Evaluation of Control System Designs

NASA Technical Reports Server (NTRS)

Mansur, M. Hossein; Colbourne, Jason D.; Chang, Yu-Kuang; Aiken, Edwin W. (Technical Monitor)

1998-01-01

The development and optimization of flight control systems for modem fixed- and rotary-. wing aircraft consume a significant portion of the overall time and cost of aircraft development. Substantial savings can be achieved if the time required to develop and flight test the control system, and the cost, is reduced. To bring about such reductions, software tools such as Matlab/Simulink are being used to readily implement block diagrams and rapidly evaluate the expected responses of the completed system. Moreover, tools such as CONDUIT (CONtrol Designer's Unified InTerface) have been developed that enable the controls engineers to optimize their control laws and ensure that all the relevant quantitative criteria are satisfied, all within a fully interactive, user friendly, unified software environment.

The path to an experiment in space (from concept to flight)

NASA Technical Reports Server (NTRS)

Salzman, Jack A.

1994-01-01

The following are discussed in this viewgraph presentation on developing flight experiments for NASA's Microgravity Science and Applications Program: time from flight PI selection to launch; key flight experiment phases and schedule drivers; microgravity experiment definition/development process; definition and engineering development phase; ground-based reduced gravity research facilities; project organization; responsibilities and duties of principle investigator/co-investigators, project scientist, and project manager; the science requirements document; flight development phase; experiment cost and schedule; and keys to experiment success.

A framework for improving access and customer service times in health care: application and analysis at the UCLA Medical Center.

PubMed

Duda, Catherine; Rajaram, Kumar; Barz, Christiane; Rosenthal, J Thomas

2013-01-01

There has been an increasing emphasis on health care efficiency and costs and on improving quality in health care settings such as hospitals or clinics. However, there has not been sufficient work on methods of improving access and customer service times in health care settings. The study develops a framework for improving access and customer service time for health care settings. In the framework, the operational concept of the bottleneck is synthesized with queuing theory to improve access and reduce customer service times without reduction in clinical quality. The framework is applied at the Ronald Reagan UCLA Medical Center to determine the drivers for access and customer service times and then provides guidelines on how to improve these drivers. Validation using simulation techniques shows significant potential for reducing customer service times and increasing access at this institution. Finally, the study provides several practice implications that could be used to improve access and customer service times without reduction in clinical quality across a range of health care settings from large hospitals to small community clinics.

Electron beam curing — taking good ideas to the manufacturing floor

NASA Astrophysics Data System (ADS)

Saunders, C.; Lopata, V.; Barnard, J.; Stepanik, T.

2000-03-01

Acsion is exploiting several emerging electron beam EB applications ranging from composite curing and repair to viscose manufacturing. EB curing of composite structures offers several advantages: significantly reduced curing times; improvements in part quality and performance; reduced environmental and health concerns; improvements in material handling; and reduced overall manufacturing costs compared to thermal curing. The aerospace industry is developing EB technology in all of their market sectors, including military aviation and space products. Some specific products include cryogenic fuel tanks, improved canopy frames for jet aircraft, and the all-composite military aircraft. This paper discusses each of these opportunities.

Control of nonlinear systems with applications to constrained robots and spacecraft attitude stabilization

NASA Technical Reports Server (NTRS)

Krishnan, Hariharan

1993-01-01

This thesis is organized in two parts. In Part 1, control systems described by a class of nonlinear differential and algebraic equations are introduced. A procedure for local stabilization based on a local state realization is developed. An alternative approach to local stabilization is developed based on a classical linearization of the nonlinear differential-algebraic equations. A theoretical framework is established for solving a tracking problem associated with the differential-algebraic system. First, a simple procedure is developed for the design of a feedback control law which ensures, at least locally, that the tracking error in the closed loop system lies within any given bound if the reference inputs are sufficiently slowly varying. Next, by imposing additional assumptions, a procedure is developed for the design of a feedback control law which ensures that the tracking error in the closed loop system approaches zero exponentially for reference inputs which are not necessarily slowly varying. The control design methodologies are used for simultaneous force and position control in constrained robot systems. The differential-algebraic equations are shown to characterize the slow dynamics of a certain nonlinear control system in nonstandard singularly perturbed form. In Part 2, the attitude stabilization (reorientation) of a rigid spacecraft using only two control torques is considered. First, the case of momentum wheel actuators is considered. The complete spacecraft dynamics are not controllable. However, the spacecraft dynamics are small time locally controllable in a reduced sense. The reduced spacecraft dynamics cannot be asymptotically stabilized using continuous feedback, but a discontinuous feedback control strategy is constructed. Next, the case of gas jet actuators is considered. If the uncontrolled principal axis is not an axis of symmetry, the complete spacecraft dynamics are small time locally controllable. However, the spacecraft attitude cannot be asymptotically stabilized using continuous feedback, but a discontinuous stabilizing feedback control strategy is constructed. If the uncontrolled principal axis is an axis of symmetry, the complete spacecraft dynamics cannot be stabilized. However, the spacecraft dynamics are small time locally controllable in a reduced sense. The reduced spacecraft dynamics cannot be asymptotically stabilized using continuous feedback, but again a discontinuous feedback control strategy is constructed.

Nonlinear dynamic theory for photorefractive phase hologram formation

NASA Technical Reports Server (NTRS)

Kim, D. M.; Shah, R. R.; Rabson, T. A.; Tittle, F. K.

1976-01-01

A nonlinear dynamic theory is developed for the formation of photorefractive volume phase holograms. A feedback mechanism existing between the photogenerated field and free-electron density, treated explicitly, yields the growth and saturation of the space-charge field in a time scale characterized by the coupling strength between them. The expression for the field reduces in the short-time limit to previous theories and approaches in the long-time limit the internal or photovoltaic field. Additionally, the phase of the space charge field is shown to be time-dependent.

Competency: an essential component of caring in nursing.

PubMed

Knapp, Bobbi

2004-01-01

Providing online e-learning for nurses significantly reduces medical errors by providing "just-in-time" reference and device training. Offering continuing education 24/7 assures continued competency in an ever-changing practice environment while fostering professional development and career mobility.

23 CFR 627.3 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-04-01

... HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION ENGINEERING AND TRAFFIC OPERATIONS VALUE ENGINEERING... construction. Value Engineering (VE) analysis. The systematic process of reviewing and assessing a project by a...; and (3) Reducing the time to develop and deliver the project. Value Engineering (VE) Job Plan. A...

23 CFR 627.3 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-04-01

... HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION ENGINEERING AND TRAFFIC OPERATIONS VALUE ENGINEERING... construction. Value Engineering (VE) analysis. The systematic process of reviewing and assessing a project by a...; and (3) Reducing the time to develop and deliver the project. Value Engineering (VE) Job Plan. A...

Microwave-assisted transformations and synthesis of polymer nanocomposites and nanomaterials

EPA Science Inventory

The use of emerging MW-assisted chemistry techniques in conjunction with greener reaction media is dramatically reducing chemical waste and reaction times in several organic transformations and material synthesis. This account summarizes our own experience in developing MW-assist...

Pointing the Way.

ERIC Educational Resources Information Center

Cowan, William M.

1984-01-01

Complying with regulations that require tactile signs to assist disabled persons is not as onerous as it seems. An intelligently developed signage system will reduce the amount of staff time needed to assist disabled people, most of whom prefer to find their own way. (TE)

The synthesis and applications of a micro-pine-structured nanocatalyst

EPA Science Inventory

The use of emerging MW-assisted chemistry techniques in conjunction with benign reaction media is dramatically reducing chemical waste and reaction times in several organic syntheses and chemical transformations. This editorial comments on the recent developments in mechanochemic...

Improvement for enhancing effectiveness of universal power system (UPS) continuous testing process

NASA Astrophysics Data System (ADS)

Sriratana, Lerdlekha

2018-01-01

This experiment aims to enhance the effectiveness of the Universal Power System (UPS) continuous testing process of the Electrical and Electronic Institute by applying work scheduling and time study methods. Initially, the standard time of testing process has not been considered that results of unaccurate testing target and also time wasting has been observed. As monitoring and reducing waste time for improving the efficiency of testing process, Yamazumi chart and job scheduling theory (North West Corner Rule) were applied to develop new work process. After the improvements, the overall efficiency of the process possibly increased from 52.8% to 65.6% or 12.7%. Moreover, the waste time could reduce from 828.3 minutes to 653.6 minutes or 21%, while testing units per batch could increase from 3 to 4 units. Therefore, the number of testing units would increase from 12 units up to 20 units per month that also contribute to increase of net income of UPS testing process by 72%.

Development of a short version of the modified Yale Preoperative Anxiety Scale.

PubMed

Jenkins, Brooke N; Fortier, Michelle A; Kaplan, Sherrie H; Mayes, Linda C; Kain, Zeev N

2014-09-01

The modified Yale Preoperative Anxiety Scale (mYPAS) is the current "criterion standard" for assessing child anxiety during induction of anesthesia and has been used in >100 studies. This observational instrument covers 5 items and is typically administered at 4 perioperative time points. Application of this complex instrument in busy operating room (OR) settings, however, presents a challenge. In this investigation, we examined whether the instrument could be modified and made easier to use in OR settings. This study used qualitative methods, principal component analyses, Cronbach αs, and effect sizes to create the mYPAS-Short Form (mYPAS-SF) and reduce time points of assessment. Data were obtained from multiple patients (N = 3798; Mage = 5.63) who were recruited in previous investigations using the mYPAS over the past 15 years. After qualitative analysis, the "use of parent" item was eliminated due to content overlap with other items. The reduced item set accounted for 82% or more of the variance in child anxiety and produced the Cronbach α of at least 0.92. To reduce the number of time points of assessment, a minimum Cohen d effect size criterion of 0.48 change in mYPAS score across time points was used. This led to eliminating the walk to the OR and entrance to the OR time points. Reducing the mYPAS to 4 items, creating the mYPAS-SF that can be administered at 2 time points, retained the accuracy of the measure while allowing the instrument to be more easily used in clinical research settings.

Development of a semi-automated model identification and calibration tool for conceptual modelling of sewer systems.

PubMed

Wolfs, Vincent; Villazon, Mauricio Florencio; Willems, Patrick

2013-01-01

Applications such as real-time control, uncertainty analysis and optimization require an extensive number of model iterations. Full hydrodynamic sewer models are not sufficient for these applications due to the excessive computation time. Simplifications are consequently required. A lumped conceptual modelling approach results in a much faster calculation. The process of identifying and calibrating the conceptual model structure could, however, be time-consuming. Moreover, many conceptual models lack accuracy, or do not account for backwater effects. To overcome these problems, a modelling methodology was developed which is suited for semi-automatic calibration. The methodology is tested for the sewer system of the city of Geel in the Grote Nete river basin in Belgium, using both synthetic design storm events and long time series of rainfall input. A MATLAB/Simulink(®) tool was developed to guide the modeller through the step-wise model construction, reducing significantly the time required for the conceptual modelling process.

Electron Beam Cured Epoxy Resin Composites for High Temperature Applications

NASA Technical Reports Server (NTRS)

Janke, Christopher J.; Dorsey, George F.; Havens, Stephen J.; Lopata, Vincent J.; Meador, Michael A.

1997-01-01

Electron beam curing of Polymer Matrix Composites (PMC's) is a nonthermal, nonautoclave curing process that has been demonstrated to be a cost effective and advantageous alternative to conventional thermal curing. Advantages of electron beam curing include: reduced manufacturing costs; significantly reduced curing times; improvements in part quality and performance; reduced environmental and health concerns; and improvement in material handling. In 1994 a Cooperative Research and Development Agreement (CRADA), sponsored by the Department of Energy Defense Programs and 10 industrial partners, was established to advance the electron beam curing of PMC technology. Over the last several years a significant amount of effort within the CRADA has been devoted to the development and optimization of resin systems and PMCs that match the performance of thermal cured composites. This highly successful materials development effort has resulted in a board family of high performance, electron beam curable cationic epoxy resin systems possessing a wide range of excellent processing and property profiles. Hundreds of resin systems, both toughened and untoughened, offering unlimited formulation and processing flexibility have been developed and evaluated in the CRADA program.

Diagnostics of wear in aeronautical systems

NASA Technical Reports Server (NTRS)

Wedeven, L. D.

1979-01-01

The use of appropriate diagnostic tools for aircraft oil wetted components is reviewed, noting that it can reduce direct operating costs through reduced unscheduled maintenance, particularly in helicopter engine and transmission systems where bearing failures are a significant cost factor. Engine and transmission wear modes are described, and diagnostic methods for oil and wet particle analysis, the spectrometric oil analysis program, chip detectors, ferrography, in-line oil monitor and radioactive isotope tagging are discussed, noting that they are effective over a limited range of particle sizes but compliment each other if used in parallel. Fine filtration can potentially increase time between overhauls, but reduces the effectiveness of conventional oil monitoring techniques so that alternative diagnostic techniques must be used. It is concluded that the development of a diagnostic system should be parallel and integral with the development of a mechanical system.

Procedures for generation and reduction of linear models of a turbofan engine

NASA Technical Reports Server (NTRS)

Seldner, K.; Cwynar, D. S.

1978-01-01

A real time hybrid simulation of the Pratt & Whitney F100-PW-F100 turbofan engine was used for linear-model generation. The linear models were used to analyze the effect of disturbances about an operating point on the dynamic performance of the engine. A procedure that disturbs, samples, and records the state and control variables was developed. For large systems, such as the F100 engine, the state vector is large and may contain high-frequency information not required for control. This, reducing the full-state to a reduced-order model may be a practicable approach to simplifying the control design. A reduction technique was developed to generate reduced-order models. Selected linear and nonlinear output responses to exhaust-nozzle area and main-burner fuel flow disturbances are presented for comparison.

An evaluation of software tools for the design and development of cockpit displays

NASA Technical Reports Server (NTRS)

Ellis, Thomas D., Jr.

1993-01-01

The use of all-glass cockpits at the NASA Langley Research Center (LaRC) simulation facility has changed the means of design, development, and maintenance of instrument displays. The human-machine interface has evolved from a physical hardware device to a software-generated electronic display system. This has subsequently caused an increased workload at the facility. As computer processing power increases and the glass cockpit becomes predominant in facilities, software tools used in the design and development of cockpit displays are becoming both feasible and necessary for a more productive simulation environment. This paper defines LaRC requirements of a display software development tool and compares two available applications against these requirements. As a part of the software engineering process, these tools reduce development time, provide a common platform for display development, and produce exceptional real-time results.

High-speed peak matching algorithm for retention time alignment of gas chromatographic data for chemometric analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, Kevin J.; Wright, Bob W.; Jarman, Kristin H.

2003-05-09

A rapid retention time alignment algorithm was developed as a preprocessing utility to be used prior to chemometric analysis of large datasets of diesel fuel gas chromatographic profiles. Retention time variation from chromatogram-to-chromatogram has been a significant impediment against the use of chemometric techniques in the analysis of chromatographic data due to the inability of current multivariate techniques to correctly model information that shifts from variable to variable within a dataset. The algorithm developed is shown to increase the efficacy of pattern recognition methods applied to a set of diesel fuel chromatograms by retaining chemical selectivity while reducing chromatogram-to-chromatogram retentionmore » time variations and to do so on a time scale that makes analysis of large sets of chromatographic data practical.« less

Longitudinal Heschl's gyrus growth during childhood and adolescence in typical development and autism.

PubMed

Prigge, Molly D; Bigler, Erin D; Fletcher, P Thomas; Zielinski, Brandon A; Ravichandran, Caitlin; Anderson, Jeffrey; Froehlich, Alyson; Abildskov, Tracy; Papadopolous, Evangelia; Maasberg, Kathryn; Nielsen, Jared A; Alexander, Andrew L; Lange, Nicholas; Lainhart, Janet

2013-04-01

Heightened auditory sensitivity and atypical auditory processing are common in autism. Functional studies suggest abnormal neural response and hemispheric activation to auditory stimuli, yet the neurodevelopment underlying atypical auditory function in autism is unknown. In this study, we model longitudinal volumetric growth of Heschl's gyrus gray matter and white matter during childhood and adolescence in 40 individuals with autism and 17 typically developing participants. Up to three time points of magnetic resonance imaging data, collected on average every 2.5 years, were examined from individuals 3-12 years of age at the time of their first scan. Consistent with previous cross-sectional studies, no group differences were found in Heschl's gyrus gray matter volume or asymmetry. However, reduced longitudinal gray matter volumetric growth was found in the right Heschl's gyrus in autism. Reduced longitudinal white matter growth in the left hemisphere was found in the right-handed autism participants. Atypical Heschl's gyrus white matter volumetric growth was found bilaterally in the autism individuals with a history of delayed onset of spoken language. Heightened auditory sensitivity, obtained from the Sensory Profile, was associated with reduced volumetric gray matter growth in the right hemisphere. Our longitudinal analyses revealed dynamic gray and white matter changes in Heschl's gyrus throughout childhood and adolescence in both typical development and autism. © 2013 International Society for Autism Research, Wiley Periodicals, Inc.

Reduced order model based on principal component analysis for process simulation and optimization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lang, Y.; Malacina, A.; Biegler, L.

2009-01-01

It is well-known that distributed parameter computational fluid dynamics (CFD) models provide more accurate results than conventional, lumped-parameter unit operation models used in process simulation. Consequently, the use of CFD models in process/equipment co-simulation offers the potential to optimize overall plant performance with respect to complex thermal and fluid flow phenomena. Because solving CFD models is time-consuming compared to the overall process simulation, we consider the development of fast reduced order models (ROMs) based on CFD results to closely approximate the high-fidelity equipment models in the co-simulation. By considering process equipment items with complicated geometries and detailed thermodynamic property models,more » this study proposes a strategy to develop ROMs based on principal component analysis (PCA). Taking advantage of commercial process simulation and CFD software (for example, Aspen Plus and FLUENT), we are able to develop systematic CFD-based ROMs for equipment models in an efficient manner. In particular, we show that the validity of the ROM is more robust within well-sampled input domain and the CPU time is significantly reduced. Typically, it takes at most several CPU seconds to evaluate the ROM compared to several CPU hours or more to solve the CFD model. Two case studies, involving two power plant equipment examples, are described and demonstrate the benefits of using our proposed ROM methodology for process simulation and optimization.« less

Aeroshell Design Techniques for Aerocapture Entry Vehicles

NASA Technical Reports Server (NTRS)

Dyke, R. Eric; Hrinda, Glenn A.

2004-01-01

A major goal of NASA s In-Space Propulsion Program is to shorten trip times for scientific planetary missions. To meet this challenge arrival speeds will increase, requiring significant braking for orbit insertion, and thus increased deceleration propellant mass that may exceed launch lift capabilities. A technology called aerocapture has been developed to expand the mission potential of exploratory probes destined for planets with suitable atmospheres. Aerocapture inserts a probe into planetary orbit via a single pass through the atmosphere using the probe s aeroshell drag to reduce velocity. The benefit of an aerocapture maneuver is a large reduction in propellant mass that may result in smaller, less costly missions and reduced mission cruise times. The methodology used to design rigid aerocapture aeroshells will be presented with an emphasis on a new systems tool under development. Current methods for fast, efficient evaluations of structural systems for exploratory vehicles to planets and moons within our solar system have been under development within NASA having limited success. Many systems tools that have been attempted applied structural mass estimation techniques based on historical data and curve fitting techniques that are difficult and cumbersome to apply to new vehicle concepts and missions. The resulting vehicle aeroshell mass may be incorrectly estimated or have high margins included to account for uncertainty. This new tool will reduce the guesswork previously found in conceptual aeroshell mass estimations.

The Large Benefits of Small-Satellite Missions

NASA Astrophysics Data System (ADS)

Baker, Daniel N.; Worden, S. Pete

2008-08-01

Small-spacecraft missions play a key and compelling role in space-based scientific and engineering programs [Moretto and Robinson, 2008]. Compared with larger satellites, which can be in excess of 2000 kilograms, small satellites range from 750 kilograms-roughly the size of a golf cart-to less than 1 kilogram, about the size of a softball. They have been responsible for greatly reducing the time needed to obtain science and technology results. The shorter development times for smaller missions can reduce overall costs and can thus provide welcome budgetary options for highly constrained space programs. In many cases, we contend that 80% (or more) of program goals can be achieved for 20% of the cost by using small-spacecraft solutions.

Rationale for continuing R&D in indirect coal liquefaction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gray, D.; Tomlinson, G.

1995-12-31

The objective of this analysis is to use the world energy demand/supply model developed at MITRE to examine future liquid fuels supply scenarios both for the world and for the United States. This analysis has determined the probable extent of future oil resource shortages and the likely time frame in which the shortages will occur. The role that coal liquefaction could play in helping to alleviate this liquid fuels shortfall is also examined. The importance of continuing R&D to improve process performance and reduce the costs of coal-derived transportation fuel is quantified in terms of reducing the time when coalmore » liquids will become competitive with petroleum.« less

Energy consumption program: A computer model simulating energy loads in buildings

NASA Technical Reports Server (NTRS)

Stoller, F. W.; Lansing, F. L.; Chai, V. W.; Higgins, S.

1978-01-01

The JPL energy consumption computer program developed as a useful tool in the on-going building modification studies in the DSN energy conservation project is described. The program simulates building heating and cooling loads and computes thermal and electric energy consumption and cost. The accuracy of computations are not sacrificed, however, since the results lie within + or - 10 percent margin compared to those read from energy meters. The program is carefully structured to reduce both user's time and running cost by asking minimum information from the user and reducing many internal time-consuming computational loops. Many unique features were added to handle two-level electronics control rooms not found in any other program.

VERSE - Virtual Equivalent Real-time Simulation

NASA Technical Reports Server (NTRS)

Zheng, Yang; Martin, Bryan J.; Villaume, Nathaniel

2005-01-01

Distributed real-time simulations provide important timing validation and hardware in the- loop results for the spacecraft flight software development cycle. Occasionally, the need for higher fidelity modeling and more comprehensive debugging capabilities - combined with a limited amount of computational resources - calls for a non real-time simulation environment that mimics the real-time environment. By creating a non real-time environment that accommodates simulations and flight software designed for a multi-CPU real-time system, we can save development time, cut mission costs, and reduce the likelihood of errors. This paper presents such a solution: Virtual Equivalent Real-time Simulation Environment (VERSE). VERSE turns the real-time operating system RTAI (Real-time Application Interface) into an event driven simulator that runs in virtual real time. Designed to keep the original RTAI architecture as intact as possible, and therefore inheriting RTAI's many capabilities, VERSE was implemented with remarkably little change to the RTAI source code. This small footprint together with use of the same API allows users to easily run the same application in both real-time and virtual time environments. VERSE has been used to build a workstation testbed for NASA's Space Interferometry Mission (SIM PlanetQuest) instrument flight software. With its flexible simulation controls and inexpensive setup and replication costs, VERSE will become an invaluable tool in future mission development.

Agile hardware and software systems engineering for critical military space applications

NASA Astrophysics Data System (ADS)

Huang, Philip M.; Knuth, Andrew A.; Krueger, Robert O.; Garrison-Darrin, Margaret A.

2012-06-01

The Multi Mission Bus Demonstrator (MBD) is a successful demonstration of agile program management and system engineering in a high risk technology application where utilizing and implementing new, untraditional development strategies were necessary. MBD produced two fully functioning spacecraft for a military/DOD application in a record breaking time frame and at dramatically reduced costs. This paper discloses the adaptation and application of concepts developed in agile software engineering to hardware product and system development for critical military applications. This challenging spacecraft did not use existing key technology (heritage hardware) and created a large paradigm shift from traditional spacecraft development. The insertion of new technologies and methods in space hardware has long been a problem due to long build times, the desire to use heritage hardware, and lack of effective process. The role of momentum in the innovative process can be exploited to tackle ongoing technology disruptions and allowing risk interactions to be mitigated in a disciplined manner. Examples of how these concepts were used during the MBD program will be delineated. Maintaining project momentum was essential to assess the constant non recurring technological challenges which needed to be retired rapidly from the engineering risk liens. Development never slowed due to tactical assessment of the hardware with the adoption of the SCRUM technique. We adapted this concept as a representation of mitigation of technical risk while allowing for design freeze later in the program's development cycle. By using Agile Systems Engineering and Management techniques which enabled decisive action, the product development momentum effectively was used to produce two novel space vehicles in a fraction of time with dramatically reduced cost.

Real-time Simulation of Turboprop Engine Control System

NASA Astrophysics Data System (ADS)

Sheng, Hanlin; Zhang, Tianhong; Zhang, Yi

2017-05-01

On account of the complexity of turboprop engine control system, real-time simulation is the technology, under the prerequisite of maintaining real-time, to effectively reduce development cost, shorten development cycle and avert testing risks. The paper takes RT-LAB as a platform and studies the real-time digital simulation of turboprop engine control system. The architecture, work principles and external interfaces of RT-LAB real-time simulation platform are introduced firstly. Then based on a turboprop engine model, the control laws of propeller control loop and fuel control loop are studied. From that and on the basis of Matlab/Simulink, an integrated controller is designed which can realize the entire process control of the engine from start-up to maximum power till stop. At the end, on the basis of RT-LAB platform, the real-time digital simulation of the designed control system is studied, different regulating plans are tried and more ideal control effects have been obtained.

Capabilities and constraints of NASA's ground-based reduced gravity facilities

NASA Technical Reports Server (NTRS)

Lekan, Jack; Neumann, Eric S.; Sotos, Raymond G.

1993-01-01

The ground-based reduced gravity facilities of NASA have been utilized to support numerous investigations addressing various processes and phenomina in several disciplines for the past 30 years. These facilities, which include drop towers, drop tubes, aircraft, and sounding rockets are able to provide a low gravity environment (gravitational levels that range from 10(exp -2)g to 10(exp -6)g) by creating a free fall or semi-free fall condition where the force of gravity on an experiment is offset by its linear acceleration during the 'fall' (drop or parabola). The low gravity condition obtained on the ground is the same as that of an orbiting spacecraft which is in a state of perpetual free fall. The gravitational levels and associated duration times associated with the full spectrum of reduced gravity facilities including spaced-based facilities are summarized. Even though ground-based facilities offer a relatively short experiment time, this available test time has been found to be sufficient to advance the scientific understanding of many phenomena and to provide meaningful hardware tests during the flight experiment development process. Also, since experiments can be quickly repeated in these facilities, multistep phenomena that have longer characteristic times associated with them can sometimes be examined in a step-by-step process. There is a large body of literature which has reported the study results achieved through using reduced-gravity data obtained from the facilities.

Two Improved Algorithms for Envelope and Wavefront Reduction

NASA Technical Reports Server (NTRS)

Kumfert, Gary; Pothen, Alex

1997-01-01

Two algorithms for reordering sparse, symmetric matrices or undirected graphs to reduce envelope and wavefront are considered. The first is a combinatorial algorithm introduced by Sloan and further developed by Duff, Reid, and Scott; we describe enhancements to the Sloan algorithm that improve its quality and reduce its run time. Our test problems fall into two classes with differing asymptotic behavior of their envelope parameters as a function of the weights in the Sloan algorithm. We describe an efficient 0(nlogn + m) time implementation of the Sloan algorithm, where n is the number of rows (vertices), and m is the number of nonzeros (edges). On a collection of test problems, the improved Sloan algorithm required, on the average, only twice the time required by the simpler Reverse Cuthill-Mckee algorithm while improving the mean square wavefront by a factor of three. The second algorithm is a hybrid that combines a spectral algorithm for envelope and wavefront reduction with a refinement step that uses a modified Sloan algorithm. The hybrid algorithm reduces the envelope size and mean square wavefront obtained from the Sloan algorithm at the cost of greater running times. We illustrate how these reductions translate into tangible benefits for frontal Cholesky factorization and incomplete factorization preconditioning.

Very low cost real time histogram-based contrast enhancer utilizing fixed-point DSP processing

NASA Astrophysics Data System (ADS)

McCaffrey, Nathaniel J.; Pantuso, Francis P.

1998-03-01

A real time contrast enhancement system utilizing histogram- based algorithms has been developed to operate on standard composite video signals. This low-cost DSP based system is designed with fixed-point algorithms and an off-chip look up table (LUT) to reduce the cost considerably over other contemporary approaches. This paper describes several real- time contrast enhancing systems advanced at the Sarnoff Corporation for high-speed visible and infrared cameras. The fixed-point enhancer was derived from these high performance cameras. The enhancer digitizes analog video and spatially subsamples the stream to qualify the scene's luminance. Simultaneously, the video is streamed through a LUT that has been programmed with the previous calculation. Reducing division operations by subsampling reduces calculation- cycles and also allows the processor to be used with cameras of nominal resolutions. All values are written to the LUT during blanking so no frames are lost. The enhancer measures 13 cm X 6.4 cm X 3.2 cm, operates off 9 VAC and consumes 12 W. This processor is small and inexpensive enough to be mounted with field deployed security cameras and can be used for surveillance, video forensics and real- time medical imaging.

Development of an Efficient Binaural Simulation for the Analysis of Structural Acoustic Data

NASA Technical Reports Server (NTRS)

Johnson, Marty E.; Lalime, Aimee L.; Grosveld, Ferdinand W.; Rizzi, Stephen A.; Sullivan, Brenda M.

2003-01-01

Applying binaural simulation techniques to structural acoustic data can be very computationally intensive as the number of discrete noise sources can be very large. Typically, Head Related Transfer Functions (HRTFs) are used to individually filter the signals from each of the sources in the acoustic field. Therefore, creating a binaural simulation implies the use of potentially hundreds of real time filters. This paper details two methods of reducing the number of real-time computations required by: (i) using the singular value decomposition (SVD) to reduce the complexity of the HRTFs by breaking them into dominant singular values and vectors and (ii) by using equivalent source reduction (ESR) to reduce the number of sources to be analyzed in real-time by replacing sources on the scale of a structural wavelength with sources on the scale of an acoustic wavelength. The ESR and SVD reduction methods can be combined to provide an estimated computation time reduction of 99.4% for the structural acoustic data tested. In addition, preliminary tests have shown that there is a 97% correlation between the results of the combined reduction methods and the results found with the current binaural simulation techniques

Ramp time synchronization. [for NASA Deep Space Network

NASA Technical Reports Server (NTRS)

Hietzke, W.

1979-01-01

A new method of intercontinental clock synchronization has been developed and proposed for possible use by NASA's Deep Space Network (DSN), using a two-way/three-way radio link with a spacecraft. Analysis of preliminary data indicates that the real-time method has an uncertainty of 0.6 microsec, and it is very likely that further work will decrease the uncertainty. Also, the method is compatible with a variety of nonreal-time analysis techniques, which may reduce the uncertainty down to the tens of nanosecond range.

The school bus routing and scheduling problem with transfers

PubMed Central

Doerner, Karl F.; Parragh, Sophie N.

2015-01-01

In this article, we study the school bus routing and scheduling problem with transfers arising in the field of nonperiodic public transportation systems. It deals with the transportation of pupils from home to their school in the morning taking the possibility that pupils may change buses into account. Allowing transfers has several consequences. On the one hand, it allows more flexibility in the bus network structure and can, therefore, help to reduce operating costs. On the other hand, transfers have an impact on the service level: the perceived service quality is lower due to the existence of transfers; however, at the same time, user ride times may be reduced and, thus, transfers may also have a positive impact on service quality. The main objective is the minimization of the total operating costs. We develop a heuristic solution framework to solve this problem and compare it with two solution concepts that do not consider transfers. The impact of transfers on the service level in terms of time loss (or user ride time) and the number of transfers is analyzed. Our results show that allowing transfers reduces total operating costs significantly while average and maximum user ride times are comparable to solutions without transfers. © 2015 Wiley Periodicals, Inc. NETWORKS, Vol. 65(2), 180–203 2015 PMID:28163329

Short Duration Reduced Gravity Drop Tower Design and Development

NASA Astrophysics Data System (ADS)

Osborne, B.; Welch, C.

The industrial and commercial development of space-related activities is intimately linked to the ability to conduct reduced gravity research. Reduced gravity experimentation is important to many diverse fields of research in the understanding of fundamental and applied aspects of physical phenomena. Both terrestrial and extra-terrestrial experimental facilities are currently available to allow researchers access to reduced gravity environments. This paper discusses two drop tower designs, a 2.0 second facility built in Australia and a proposed 2.2 second facility in the United Kingdom. Both drop towers utilise a drag shield for isolating the falling experiment from the drag forces of the air during the test. The design and development of The University of Queensland's (Australia) 2.0 second drop tower, including its specifications and operational procedures is discussed first. Sensitive aspects of the design process are examined. Future plans are then presented for a new short duration (2.2 sec) ground-based reduced gravity drop tower. The new drop tower has been designed for Kingston University (United Kingdom) to support teaching and research in the field of reduced gravity physics. The design has been informed by the previous UQ drop tower design process and utilises a catapult mechanism to increase test time and also incorporates features to allow participants for a variety of backgrounds (from high school students through to university researchers) to learn and experiment in reduced gravity. Operational performance expectations for this new facility are also discussed.

Application of ubiquitous computing in personal health monitoring systems.

PubMed

Kunze, C; Grossmann, U; Stork, W; Müller-Glaser, K D

2002-01-01

A possibility to significantly reduce the costs of public health systems is to increasingly use information technology. The Laboratory for Information Processing Technology (ITIV) at the University of Karlsruhe is developing a personal health monitoring system, which should improve health care and at the same time reduce costs by combining micro-technological smart sensors with personalized, mobile computing systems. In this paper we present how ubiquitous computing theory can be applied in the health-care domain.

A novel approach to estimate emissions from large transportation networks: Hierarchical clustering-based link-driving-schedules for EPA-MOVES using dynamic time warping measures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aziz, H. M. Abdul; Ukkusuri, Satish V.

We present that EPA-MOVES (Motor Vehicle Emission Simulator) is often integrated with traffic simulators to assess emission levels of large-scale urban networks with signalized intersections. High variations in speed profiles exist in the context of congested urban networks with signalized intersections. The traditional average-speed-based emission estimation technique with EPA-MOVES provides faster execution while underestimates the emissions in most cases because of ignoring the speed variation at congested networks with signalized intersections. In contrast, the atomic second-by-second speed profile (i.e., the trajectory of each vehicle)-based technique provides accurate emissions at the cost of excessive computational power and time. We addressed thismore » issue by developing a novel method to determine the link-driving-schedules (LDSs) for the EPA-MOVES tool. Our research developed a hierarchical clustering technique with dynamic time warping similarity measures (HC-DTW) to find the LDS for EPA-MOVES that is capable of producing emission estimates better than the average-speed-based technique with execution time faster than the atomic speed profile approach. We applied the HC-DTW on a sample data from a signalized corridor and found that HC-DTW can significantly reduce computational time without compromising the accuracy. The developed technique in this research can substantially contribute to the EPA-MOVES-based emission estimation process for large-scale urban transportation network by reducing the computational time with reasonably accurate estimates. This method is highly appropriate for transportation networks with higher variation in speed such as signalized intersections. Lastly, experimental results show error difference ranging from 2% to 8% for most pollutants except PM 10.« less

A novel approach to estimate emissions from large transportation networks: Hierarchical clustering-based link-driving-schedules for EPA-MOVES using dynamic time warping measures

DOE PAGES

Aziz, H. M. Abdul; Ukkusuri, Satish V.

2017-06-29

We present that EPA-MOVES (Motor Vehicle Emission Simulator) is often integrated with traffic simulators to assess emission levels of large-scale urban networks with signalized intersections. High variations in speed profiles exist in the context of congested urban networks with signalized intersections. The traditional average-speed-based emission estimation technique with EPA-MOVES provides faster execution while underestimates the emissions in most cases because of ignoring the speed variation at congested networks with signalized intersections. In contrast, the atomic second-by-second speed profile (i.e., the trajectory of each vehicle)-based technique provides accurate emissions at the cost of excessive computational power and time. We addressed thismore » issue by developing a novel method to determine the link-driving-schedules (LDSs) for the EPA-MOVES tool. Our research developed a hierarchical clustering technique with dynamic time warping similarity measures (HC-DTW) to find the LDS for EPA-MOVES that is capable of producing emission estimates better than the average-speed-based technique with execution time faster than the atomic speed profile approach. We applied the HC-DTW on a sample data from a signalized corridor and found that HC-DTW can significantly reduce computational time without compromising the accuracy. The developed technique in this research can substantially contribute to the EPA-MOVES-based emission estimation process for large-scale urban transportation network by reducing the computational time with reasonably accurate estimates. This method is highly appropriate for transportation networks with higher variation in speed such as signalized intersections. Lastly, experimental results show error difference ranging from 2% to 8% for most pollutants except PM 10.« less

[Time based management in health care system: the chosen aspects].

PubMed

Kobza, Joanna; Syrkiewicz-Świtała, Magdalena

2014-01-01

Time-based management (TBM) is the key element of the whole management process. For many years in health care systems of highly developed countries modern and effective methods of time-based management have been implemented in both primary health care and hospitals (emergency departments and operating rooms). Over the past two decades a systematic review of Polish literature (since 1990) and peer reviewed articles published in international journals based on PubMed/Medline (2001-2011) have been carried out. The collected results indicate that the demographic and health changes in the populations are one of the main challenges facing general practitioners in the nearest future. Time-based management needs new and effective tools and skills, i.e., identification of priorities, well designed planning, delegation of the tasks, proper coordination, and creation of primary care teams that include additional members and human resources management. Proper reimbursement of health services, development of IT in health care system, better collection, storage, processing, analysis and exchange of information and research findings will also be needed. The use of innovative technologies, like telemedicine consultations, provides the possibility of reducing waiting time for diagnosis and treatment and in some cases could be applied in terms of secondary care. To improve the efficiency of operating rooms it is necessary to introduce different solutions, such as operating room coordinator involvement, application of automation to guide decision-making or use of robotic tools to assist surgical procedures. Overcrowded emergency departments have a major detrimental effect on the quality of hospital functions, therefore, efforts should be made to reduce them. Time-based management training among physicians and health care management in Poland, as well as the implementation of practice-based solutions still applied in highly developed countries seem to be necessary.

Civil helicopter propulsion system reliability and engine monitoring technology assessments

NASA Technical Reports Server (NTRS)

Murphy, J. A.; Zuk, J.

1982-01-01

A study to reduce operating costs of helicopters, particularly directed at the maintenance of the propulsion subsystem, is presented. The tasks of the study consisted of problem definition refinement, technology solutions, diagnostic system concepts, and emergency power augmentation. Quantifiable benefits (reduced fuel consumption, on-condition engine maintenance, extended drive system overhaul periods, and longer oil change intervals) would increase the initial cost by $43,000, but the benefit of $24.46 per hour would result in breakeven at 1758 hours. Other benefits not capable of being quantified but perhaps more important include improved aircraft avilability due to reduced maintenance time, potential for increased operating limits due to continuous automatic monitoring of gages, and less time and fuel required to make engine power checks. The most important improvement is the on-condition maintenance program, which will require the development of algorithms, equipment, and procedures compatible with all operating environments.

Fivefold confinement time increase in the Madison Symmetric Torus using inductive poloidal current drive

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stoneking, M.R.; Lanier, N.E.; Prager, S.C.

1996-12-01

Current profile control is employed in the Madison Symmetric Torus reversed field pinch to reduce the magnetic fluctuations responsible for anomalous transport. An inductive poloidal electric field pulse is applied in the sense to flatten the parallel current profile, reducing the dynamo fluctuation amplitude required to sustain the equilibrium. This technique demonstrates a substantial reduction in fluctuation amplitude (as much as 50%), and improvement in energy confinement (from 1 ms to 5 ms); a record low fluctuation (0.8%) and record high temperature (615 eV) for this device were observed simultaneously during current drive experiments. Plasma beta increases by 50% andmore » the Ohmic input power is three times lower. Particle confinement improves and plasma impurity contamination is reduced. The results of the transient current drive experiments provide motivation for continuing development of steady-state current profile control strategies for the reversed field pinch.« less

Active Learning of Classification Models with Likert-Scale Feedback.

PubMed

Xue, Yanbing; Hauskrecht, Milos

2017-01-01

Annotation of classification data by humans can be a time-consuming and tedious process. Finding ways of reducing the annotation effort is critical for building the classification models in practice and for applying them to a variety of classification tasks. In this paper, we develop a new active learning framework that combines two strategies to reduce the annotation effort. First, it relies on label uncertainty information obtained from the human in terms of the Likert-scale feedback. Second, it uses active learning to annotate examples with the greatest expected change. We propose a Bayesian approach to calculate the expectation and an incremental SVM solver to reduce the time complexity of the solvers. We show the combination of our active learning strategy and the Likert-scale feedback can learn classification models more rapidly and with a smaller number of labeled instances than methods that rely on either Likert-scale labels or active learning alone.

Active Learning of Classification Models with Likert-Scale Feedback

PubMed Central

Xue, Yanbing; Hauskrecht, Milos

2017-01-01

Annotation of classification data by humans can be a time-consuming and tedious process. Finding ways of reducing the annotation effort is critical for building the classification models in practice and for applying them to a variety of classification tasks. In this paper, we develop a new active learning framework that combines two strategies to reduce the annotation effort. First, it relies on label uncertainty information obtained from the human in terms of the Likert-scale feedback. Second, it uses active learning to annotate examples with the greatest expected change. We propose a Bayesian approach to calculate the expectation and an incremental SVM solver to reduce the time complexity of the solvers. We show the combination of our active learning strategy and the Likert-scale feedback can learn classification models more rapidly and with a smaller number of labeled instances than methods that rely on either Likert-scale labels or active learning alone. PMID:28979827

Workspace definition for navigated control functional endoscopic sinus surgery

NASA Astrophysics Data System (ADS)

Gessat, Michael; Hofer, Mathias; Audette, Michael; Dietz, Andreas; Meixensberger, Jürgen; Stauß, Gero; Burgert, Oliver

2007-03-01

For the pre-operative definition of a surgical workspace for Navigated Control ® Functional Endoscopic Sinus Surgery (FESS), we developed a semi-automatic image processing system. Based on observations of surgeons using a manual system, we implemented a workflow-based engineering process that led us to the development of a system reducing time and workload spent during the workspace definition. The system uses a feature based on local curvature to align vertices of a polygonal outline along the bone structures defining the cavities of the inner nose. An anisotropic morphologic operator was developed solve problems arising from artifacts from noise and partial volume effects. We used time measurements and NASA's TLX questionnaire to evaluate our system.

Prevalence of low back symptoms and its consequences in relation to occupational group.

PubMed

Widanarko, Baiduri; Legg, Stephen; Stevenson, Mark; Devereux, Jason; Jones, Geoff

2013-05-01

The purpose of this study was to examine: (1) the prevalence of low back symptoms (LBS) and its consequences (reduced activities and absenteeism); (2) the association between occupational group and LBS; and (3) the association between LBS and its consequences. A self-administered questionnaire was used to determine the prevalence of LBS in 1,294 Indonesian coal mining workers. A Cox proportional hazards model was developed to quantify the 12-monthly hazard of LBS. Logistic regression models were developed to identify risk factors for reduced activity and absenteeism from the workplace. The 12-month period prevalence for LBS, reduced activities, and absenteeism were 75%, 16%, and 13%, respectively. The 12-monthly hazard of LBS for blue-collar workers was 1.85 (95% CI: 1.06-3.25) times that of white-collar workers. LBS and smoking increased the risk of reduced activity and absenteeism. Indonesian coal mining workers have a high prevalence of LBS. The findings imply that efforts to reduce LBS and in the workplace should focus on blue-collar workers. For smokers who report reduced activities and/or absenteeism, there should be a focus on rehabilitation and/or return-to-work programs. Copyright © 2012 Wiley Periodicals, Inc.

The Unlock Project: a Python-based framework for practical brain-computer interface communication "app" development.

PubMed

Brumberg, Jonathan S; Lorenz, Sean D; Galbraith, Byron V; Guenther, Frank H

2012-01-01

In this paper we present a framework for reducing the development time needed for creating applications for use in non-invasive brain-computer interfaces (BCI). Our framework is primarily focused on facilitating rapid software "app" development akin to current efforts in consumer portable computing (e.g. smart phones and tablets). This is accomplished by handling intermodule communication without direct user or developer implementation, instead relying on a core subsystem for communication of standard, internal data formats. We also provide a library of hardware interfaces for common mobile EEG platforms for immediate use in BCI applications. A use-case example is described in which a user with amyotrophic lateral sclerosis participated in an electroencephalography-based BCI protocol developed using the proposed framework. We show that our software environment is capable of running in real-time with updates occurring 50-60 times per second with limited computational overhead (5 ms system lag) while providing accurate data acquisition and signal analysis.

Advancing satellite operations with intelligent graphical monitoring systems

NASA Technical Reports Server (NTRS)

Hughes, Peter M.; Shirah, Gregory W.; Luczak, Edward C.

1993-01-01

For nearly twenty-five years, spacecraft missions have been operated in essentially the same manner: human operators monitor displays filled with alphanumeric text watching for limit violations or other indicators that signal a problem. The task is performed predominately by humans. Only in recent years have graphical user interfaces and expert systems been accepted within the control center environment to help reduce operator workloads. Unfortunately, the development of these systems is often time consuming and costly. At the NASA Goddard Space Flight Center (GSFC), a new domain specific expert system development tool called the Generic Spacecraft Analyst Assistant (GenSAA) has been developed. Through the use of a highly graphical user interface and point-and-click operation, GenSAA facilitates the rapid, 'programming-free' construction of intelligent graphical monitoring systems to serve as real-time, fault-isolation assistants for spacecraft analysts. Although specifically developed to support real-time satellite monitoring, GenSAA can support the development of intelligent graphical monitoring systems in a variety of space and commercial applications.

The pivotal role of multimodality reporter sensors in drug discovery: from cell based assays to real time molecular imaging.

PubMed

Ray, Pritha

2011-04-01

Development and marketing of new drugs require stringent validation that are expensive and time consuming. Non-invasive multimodality molecular imaging using reporter genes holds great potential to expedite these processes at reduced cost. New generations of smarter molecular imaging strategies such as Split reporter, Bioluminescence resonance energy transfer, Multimodality fusion reporter technologies will further assist to streamline and shorten the drug discovery and developmental process. This review illustrates the importance and potential of molecular imaging using multimodality reporter genes in drug development at preclinical phases.

Remote Sensing: A valuable tool in the Forest Service decision making process. [in Utah

NASA Technical Reports Server (NTRS)

Stanton, F. L.

1975-01-01

Forest Service studies for integrating remotely sensed data into existing information systems highlight a need to: (1) re-examine present methods of collecting and organizing data, (2) develop an integrated information system for rapidly processing and interpreting data, (3) apply existing technological tools in new ways, and (4) provide accurate and timely information for making right management decisions. The Forest Service developed an integrated information system using remote sensors, microdensitometers, computer hardware and software, and interactive accessories. Their efforts substantially reduce the time it takes for collecting and processing data.

Tackle fescue toxicosis with spring strategies

USDA-ARS?s Scientific Manuscript database

Understanding times of the year when pastures are most toxic can be useful in developing management approaches to alleviate or reduce the severity of toxicosis. Content of ergot alkaloids in fescue vary considerably during the growing season, with the trends generally following the seasonal growth ...

Development of microsatellite markers in Parthenium ssp.

USDA-ARS?s Scientific Manuscript database

Molecular markers provide the most efficient means to study genetic diversity within and among species of a particular genus. In addition, molecular markers can facilitate breeding efforts by providing tools necessary to reduce the time required to obtain recombinant genotypes with improved agricu...

Data analysis and detection methods for on-line health monitoring of bridge structures

DOT National Transportation Integrated Search

2002-06-01

Developing an efficient structural health monitoring (SHM) technique is important for reducing potential hazards posed : to the public by damaged civil structures. The ultimate goal of applying SHM is to real-time detect, localize, and quantify : the...

Human factors in airway facilities maintenance : development of a prototype outage assessment inventory.

DOT National Transportation Integrated Search

1994-02-01

The airway facilities (AF) maintenance community is concerned with identifying ways of reducing both the incidence of equipment failure and the amount of time required to restore equipment to operational status following a failure. It is vitally impo...

German 1990: Intensive and Diverse.

ERIC Educational Resources Information Center

Kempf, Franz R.

1990-01-01

Suggests the following methods for improving university-level German language education curricula: reduce skill-development time through immersion programs, adopt Zertifikat Deutsch als Fremdsprache as the proficiency standard for advanced students, and include literature from a variety of liberal arts disciplines in the reading materials for…

Overset Grid Methods Applied to Nonlinear Potential Flows

NASA Technical Reports Server (NTRS)

Holst, Terry; Kwak, Dochan (Technical Monitor)

2000-01-01

The objectives of this viewgraph presentation are to develop Chimera-based potential methodology which is compatible with overflow and overflow infrastructure, creating options for an advanced problem solving environment and to significantly reduce turnaround time for aerodynamic analysis and design (primarily cruise conditions).

High-power transmitter automation, part 2

NASA Technical Reports Server (NTRS)

Gregg, M. A.

1981-01-01

The current status of the transmitter automation development is reported. The work described is applicable to all transmitters in the Deep Space Network. New interface and software designs are described which improve reliability and reduce the time required for subsystem turn on and klystron saturation.

Linking Asthma Exacerbation and Air Pollution Data: A Step Toward Public Health and Environmental Data Integration

NASA Technical Reports Server (NTRS)

Faruque, Fazlay; Finley, Richard; Marshall, Gailen; Brackin, Bruce; Li, Hui; Williams, Worth; Al-Hamdan, Mohammad; Luvall, Jeffrey; Rickman, Doug; Crosson, Bill

2006-01-01

Studies have shown that reducing exposure to triggers such as air pollutants can reduce symptoms and the need for medication in asthma patients. However, systems that track asthma are generally not integrated with those that track environmental hazards related to asthma. Tlvs lack of integration hinders public health awareness and responsiveness to these environmental triggers. The current study is a collaboration between health and environmental professionals to utilize NASA-derived environmental data to develop a decision support system (DSS) for asthma prediction, surveillance, and intervention. The investigators link asthma morbidity data from the University of Mississippi Medical Center (UMMC) and Mississippi Department of Health (MDH) with air quality data from the Mississippi Department of Environmental Quality (MDEQ) and remote sensing data from NASA. Daily ambient environmental hazard data for PM2.5 and ozone are obtained from the MDEQ air quality monitoring locations and are combined with remotely sensed data from NASA to develop a state-wide spatial and time series profile of environmental air quality. These data are then used to study the correlation of these measures of air quality variation with the asthma exacerbation incidence throughout the state over time. The goal is to utilize these readily available measures to allow real-time risk assessment for asthma exacerbations. GeoMedStat, a DSS previously developed for biosurveillance, will integrate these measures to monitor, analyze and report the real-time risk assessment for asthma exacerbation throughout the state.

Cost consequences due to reduced ulcer healing times - analyses based on the Swedish Registry of Ulcer Treatment.

PubMed

Öien, Rut F; Forssell, Henrik; Ragnarson Tennvall, Gunnel

2016-10-01

Resource use and costs for topical treatment of hard-to-heal ulcers based on data from the Swedish Registry of Ulcer Treatment (RUT) were analysed in patients recorded in RUT as having healed between 2009 and 2012, in order to estimate potential cost savings from reductions in frequency of dressing changes and healing times. RUT is used to capture areas of improvement in ulcer care and to enable structured wound management by registering patients with hard-to-heal leg, foot and pressure ulcers. Patients included in the registry are treated in primary care, community care, private care, and inpatient hospital care. Cost calculations were based on resource use data on healing time and frequency of dressing changes in Swedish patients with hard-to-heal ulcers who healed between 2009 and 2012. Per-patient treatment costs decreased from SEK38 223 in 2009 to SEK20 496 in 2012, mainly because of shorter healing times. Frequency of dressing changes was essentially the same during these years, varying from 1·4 to 1·6 per week. The total healing time was reduced by 38%. Treatment costs for the management of hard-to-heal ulcers can be reduced with well-developed treatment strategies resulting in shortened healing times as shown in RUT. © 2015 Medicalhelplines.com Inc and John Wiley & Sons Ltd.

A mobile technology intervention to reduce sedentary behaviour in 2- to 4-year-old children (Mini Movers): study protocol for a randomised controlled trial.

PubMed

Downing, Katherine L; Salmon, Jo; Hinkley, Trina; Hnatiuk, Jill A; Hesketh, Kylie D

2017-03-03

Sedentary behaviour (e.g. television viewing, sitting time) tracks over time and is associated with adverse health and developmental outcomes across the lifespan. Young children (5 years or younger) spend up to 12 h/day sedentary, of which around 2 h is spent in screen time (e.g. watching television). Interventions to reduce sedentary behaviour in early childhood report mixed results and many have limited potential for scalability. Mobile phones offer a wide-reaching, low-cost avenue for the delivery of health behaviour programmes to parents but their potential to reduce young children's sedentary behaviour has not been widely tested. This study aims to test the feasibility and efficacy of a parent-focused, predominantly mobile telephone-delivered intervention to support parents to minimise the amount of time their child spends using screens and in overall sitting time. Mini Movers is a pilot randomised controlled trial recruiting 100 parents and children. Inclusion criteria include having a child aged between 2 and 4 years, being able to speak, read and write English, and smartphone ownership. Participants will be randomised to the intervention or a wait-list control group at a 1:1 ratio. Intervention group parents will receive printed materials including a content booklet and goal-checking magnet and will participate in a one-on-one discussion with the interventionist to plan two goals to reduce their child's sedentary behaviour. Subsequently, the intervention will be delivered over 6 weeks via personalised and interactive text messages promoting positive health behaviours (strategies for decreasing screen time and overall sitting time), goal setting and self-monitoring. Outcomes to be assessed include intervention feasibility and children's screen time and objectively-assessed sitting time. Few studies have used mobile phone technology to deliver health behaviour programmes to parents of young children. Findings will inform the development of larger-scale interventions to reduce sedentary behaviour during early childhood. Australian New Zealand Clinical Trials registry, identifier: ACTRN12616000628448 . Prospectively registered on 16 May 2016.

Reduced-Volume Fracture Toughness Characterization for Transparent Polymers

DTIC Science & Technology

2015-03-21

Caruthers et al. (2004) developed a thermodynamically consistent, nonlinear viscoelastic bulk constitutive model based on a potential energy clock ( PEC ...except that relaxation times change. Because of its formulation, the PEC model predicts mechanical yield as a natural consequence of relaxation...softening type of behavior, but hysteresis effects are not naturally accounted for. Adolf et al. (2009) developed a method of simplifying the PEC model

Influence of regeneration method and tissue source on the frequency of somatic variation in Populus to infection by Septoria musiva

Treesearch

Michael E. Ostry; Ronald L. Hackett; Charles H. Michler; R. Serres; B. McCown

1994-01-01

Septoria leaf spot and canker are serious diseases of many hybrid poplar clones in plantations established for biomass production. Developing resistant clones through breeding is the best long-term strategy to minimize tree damage caused by this disease. Tissue culture and somaclonal selection techniques may reduce the time needed to develop disease resistance in...

The nexus between energy consumption and financial development: estimating the role of globalization in Next-11 countries.

PubMed

Danish; Saud, Shah; Baloch, Muhammad Awais; Lodhi, Rab Nawaz

2018-04-28

In the modern era of globalization, the economic activities expand with the passage of time. This expansion may increase demand for energy both in developing and developed countries. Therefore, this study assesses the impact of financial development on energy consumption incorporating the role of globalization in Next-11 countries. A group of panel estimation techniques is used to analyze the panel data and time series data for the time 1990-2014. The empirical results of the study suggest that financial development stimulates energy consumption. Also, globalization increases demand for energy consumption, although the single country analysis suggests that the effect of globalization on energy demand is heterogeneous among N-11 countries. Furthermore, feedback hypothesis is confirmed between financial development and energy consumption. Also, bidirectional causality is found between economic growth and energy consumption. The findings urge for the attention of policymaker in emerging countries to develop a strategy to reduce the consequences of energy consumption by controlling resource transfer through globalization to the host country and by adopting energy conversation policies.

An Evolving Worldview: Making Open Source Easy

NASA Astrophysics Data System (ADS)

Rice, Z.

2017-12-01

NASA Worldview is an interactive interface for browsing full-resolution, global satellite imagery. Worldview supports an open data policy so that academia, private industries and the general public can use NASA's satellite data to address Earth science related issues. Worldview was open sourced in 2014. By shifting to an open source approach, the Worldview application has evolved to better serve end-users. Project developers are able to have discussions with end-users and community developers to understand issues and develop new features. Community developers are able to track upcoming features, collaborate on them and make their own contributions. Developers who discover issues are able to address those issues and submit a fix. This reduces the time it takes for a project developer to reproduce an issue or develop a new feature. Getting new developers to contribute to the project has been one of the most important and difficult aspects of open sourcing Worldview. After witnessing potential outside contributors struggle, a focus has been made on making the installation of Worldview simple to reduce the initial learning curve and make contributing code easy. One way we have addressed this is through a simplified setup process. Our setup documentation includes a set of prerequisites and a set of straightforward commands to clone, configure, install and run. This presentation will emphasize our focus to simplify and standardize Worldview's open source code so that more people are able to contribute. The more people who contribute, the better the application will become over time.

Finite element based electric motor design optimization

NASA Technical Reports Server (NTRS)

Campbell, C. Warren

1993-01-01

The purpose of this effort was to develop a finite element code for the analysis and design of permanent magnet electric motors. These motors would drive electromechanical actuators in advanced rocket engines. The actuators would control fuel valves and thrust vector control systems. Refurbishing the hydraulic systems of the Space Shuttle after each flight is costly and time consuming. Electromechanical actuators could replace hydraulics, improve system reliability, and reduce down time.

Optimal sampling strategies for detecting zoonotic disease epidemics.

PubMed

Ferguson, Jake M; Langebrake, Jessica B; Cannataro, Vincent L; Garcia, Andres J; Hamman, Elizabeth A; Martcheva, Maia; Osenberg, Craig W

2014-06-01

The early detection of disease epidemics reduces the chance of successful introductions into new locales, minimizes the number of infections, and reduces the financial impact. We develop a framework to determine the optimal sampling strategy for disease detection in zoonotic host-vector epidemiological systems when a disease goes from below detectable levels to an epidemic. We find that if the time of disease introduction is known then the optimal sampling strategy can switch abruptly between sampling only from the vector population to sampling only from the host population. We also construct time-independent optimal sampling strategies when conducting periodic sampling that can involve sampling both the host and the vector populations simultaneously. Both time-dependent and -independent solutions can be useful for sampling design, depending on whether the time of introduction of the disease is known or not. We illustrate the approach with West Nile virus, a globally-spreading zoonotic arbovirus. Though our analytical results are based on a linearization of the dynamical systems, the sampling rules appear robust over a wide range of parameter space when compared to nonlinear simulation models. Our results suggest some simple rules that can be used by practitioners when developing surveillance programs. These rules require knowledge of transition rates between epidemiological compartments, which population was initially infected, and of the cost per sample for serological tests.

Robust LS-SVM-based adaptive constrained control for a class of uncertain nonlinear systems with time-varying predefined performance

NASA Astrophysics Data System (ADS)

Luo, Jianjun; Wei, Caisheng; Dai, Honghua; Yuan, Jianping

2018-03-01

This paper focuses on robust adaptive control for a class of uncertain nonlinear systems subject to input saturation and external disturbance with guaranteed predefined tracking performance. To reduce the limitations of classical predefined performance control method in the presence of unknown initial tracking errors, a novel predefined performance function with time-varying design parameters is first proposed. Then, aiming at reducing the complexity of nonlinear approximations, only two least-square-support-vector-machine-based (LS-SVM-based) approximators with two design parameters are required through norm form transformation of the original system. Further, a novel LS-SVM-based adaptive constrained control scheme is developed under the time-vary predefined performance using backstepping technique. Wherein, to avoid the tedious analysis and repeated differentiations of virtual control laws in the backstepping technique, a simple and robust finite-time-convergent differentiator is devised to only extract its first-order derivative at each step in the presence of external disturbance. In this sense, the inherent demerit of backstepping technique-;explosion of terms; brought by the recursive virtual controller design is conquered. Moreover, an auxiliary system is designed to compensate the control saturation. Finally, three groups of numerical simulations are employed to validate the effectiveness of the newly developed differentiator and the proposed adaptive constrained control scheme.

Robotic navigation and ablation.

PubMed

Malcolme-Lawes, L; Kanagaratnam, P

2010-12-01

Robotic technologies have been developed to allow optimal catheter stability and reproducible catheter movements with the aim of achieving contiguous and transmural lesion delivery. Two systems for remote navigation of catheters within the heart have been developed; the first is based on a magnetic navigation system (MNS) Niobe, Stereotaxis, Saint-Louis, Missouri, USA, the second is based on a steerable sheath system (Sensei, Hansen Medical, Mountain View, CA, USA). Both robotic and magnetic navigation systems have proven to be feasible for performing ablation of both simple and complex arrhythmias, particularly atrial fibrillation. Studies to date have shown similar success rates for AF ablation compared to that of manual ablation, with many groups finding a reduction in fluoroscopy times. However, the early learning curve of cases demonstrated longer procedure times, mainly due to additional setup times. With centres performing increasing numbers of robotic ablations and the introduction of a pressure monitoring system, lower power settings and instinctive driving software, complication rates are reducing, and fluoroscopy times have been lower than manual ablation in many studies. As the demand for catheter ablation for arrhythmias such as atrial fibrillation increases and the number of centres performing these ablations increases, the demand for systems which reduce the hand skill requirement and improve the comfort of the operator will also increase.

Development of a gastroretentive pulsatile drug delivery platform.

PubMed

Thitinan, Sumalee; McConville, Jason T

2012-04-01

To develop a novel gastroretentive pulsatile drug delivery platform by combining the advantages of floating dosage forms for the stomach and pulsatile drug delivery systems. A gastric fluid impermeable capsule body was used as a vessel to contain one or more drug layer(s) as well as one or more lag-time controlling layer(s). A controlled amount of air was sealed in the innermost portion of the capsule body to reduce the overall density of the drug delivery platform, enabling gastric floatation. An optimal mass fill inside the gastric fluid impermeable capsule body enabled buoyancy in a vertical orientation to provide a constant surface area for controlled erosion of the lag-time controlling layer. The lag-time controlling layer consisted of a swellable polymer, which rapidly formed a gel to seal the mouth of capsule body and act as a barrier to gastric fluid ingress. By varying the composition of the lag-time controlling layer, it was possible to selectively program the onset of the pulsatile delivery of a drug. This new delivery platform offers a new method of delivery for a variety of suitable drugs targeted in chronopharmaceutical therapy. This strategy could ultimately improve drug efficacy and patient compliance, and reduce harmful side effects by scaling back doses of drug administered. © 2012 The Authors. JPP © 2012 Royal Pharmaceutical Society.

Peak-Seeking Optimization of Trim for Reduced Fuel Consumption: Flight-Test Results

NASA Technical Reports Server (NTRS)

Brown, Nelson Andrew; Schaefer, Jacob Robert

2013-01-01

A peak-seeking control algorithm for real-time trim optimization for reduced fuel consumption has been developed by researchers at the National Aeronautics and Space Administration (NASA) Dryden Flight Research Center to address the goals of the NASA Environmentally Responsible Aviation project to reduce fuel burn and emissions. The peak-seeking control algorithm is based on a steepest-descent algorithm using a time-varying Kalman filter to estimate the gradient of a performance function of fuel flow versus control surface positions. In real-time operation, deflections of symmetric ailerons, trailing-edge flaps, and leading-edge flaps of an F/A-18 airplane (McDonnell Douglas, now The Boeing Company, Chicago, Illinois) are used for optimization of fuel flow. Results from six research flights are presented herein. The optimization algorithm found a trim configuration that required approximately 3 percent less fuel flow than the baseline trim at the same flight condition. The algorithm consistently rediscovered the solution from several initial conditions. These results show that the algorithm has good performance in a relevant environment.

A Model Independent S/W Framework for Search-Based Software Testing

PubMed Central

Baik, Jongmoon

2014-01-01

In Model-Based Testing (MBT) area, Search-Based Software Testing (SBST) has been employed to generate test cases from the model of a system under test. However, many types of models have been used in MBT. If the type of a model has changed from one to another, all functions of a search technique must be reimplemented because the types of models are different even if the same search technique has been applied. It requires too much time and effort to implement the same algorithm over and over again. We propose a model-independent software framework for SBST, which can reduce redundant works. The framework provides a reusable common software platform to reduce time and effort. The software framework not only presents design patterns to find test cases for a target model but also reduces development time by using common functions provided in the framework. We show the effectiveness and efficiency of the proposed framework with two case studies. The framework improves the productivity by about 50% when changing the type of a model. PMID:25302314

Peak-Seeking Optimization of Trim for Reduced Fuel Consumption: Flight-test Results

NASA Technical Reports Server (NTRS)

Brown, Nelson Andrew; Schaefer, Jacob Robert

2013-01-01

A peak-seeking control algorithm for real-time trim optimization for reduced fuel consumption has been developed by researchers at the National Aeronautics and Space Administration (NASA) Dryden Flight Research Center to address the goals of the NASA Environmentally Responsible Aviation project to reduce fuel burn and emissions. The peak-seeking control algorithm is based on a steepest-descent algorithm using a time-varying Kalman filter to estimate the gradient of a performance function of fuel flow versus control surface positions. In real-time operation, deflections of symmetric ailerons, trailing-edge flaps, and leading-edge flaps of an F/A-18 airplane (McDonnell Douglas, now The Boeing Company, Chicago, Illinois) are used for optimization of fuel flow. Results from six research flights are presented herein. The optimization algorithm found a trim configuration that required approximately 3 percent less fuel flow than the baseline trim at the same flight condition. The algorithm consistently rediscovered the solution from several initial conditions. These results show that the algorithm has good performance in a relevant environment.

Nonlinear Reduced-Order Analysis with Time-Varying Spatial Loading Distributions

NASA Technical Reports Server (NTRS)

Prezekop, Adam

2008-01-01

Oscillating shocks acting in combination with high-intensity acoustic loadings present a challenge to the design of resilient hypersonic flight vehicle structures. This paper addresses some features of this loading condition and certain aspects of a nonlinear reduced-order analysis with emphasis on system identification leading to formation of a robust modal basis. The nonlinear dynamic response of a composite structure subject to the simultaneous action of locally strong oscillating pressure gradients and high-intensity acoustic loadings is considered. The reduced-order analysis used in this work has been previously demonstrated to be both computationally efficient and accurate for time-invariant spatial loading distributions, provided that an appropriate modal basis is used. The challenge of the present study is to identify a suitable basis for loadings with time-varying spatial distributions. Using a proper orthogonal decomposition and modal expansion, it is shown that such a basis can be developed. The basis is made more robust by incrementally expanding it to account for changes in the location, frequency and span of the oscillating pressure gradient.

Utilizing a Human Factors Nursing Worksystem Improvement Framework to Increase Nurses' Time at the Bedside and Enhance Safety.

PubMed

Probst, C Adam; Carter, Megan; Cadigan, Caton; Dalcour, Cortney; Cassity, Cindy; Quinn, Penny; Williams, Tiana; Montgomery, Donna Cook; Wilder, Claudia; Xiao, Yan

2017-02-01

The aim of this study is to increase nurses' time for direct patient care and improve safety via a novel human factors framework for nursing worksystem improvement. Time available for direct patient care influences outcomes, yet worksystem barriers prevent nurses adequate time at the bedside. A novel human factors framework was developed for worksystem improvement in 3 units at 2 facilities. Objectives included improving nurse efficiency as measured by time-and-motion studies, reducing missing medications and subsequent trips to medication rooms and improving medication safety. Worksystem improvement resulted in time savings of 16% to 32% per nurse per 12-hour shift. Requests for missing medications dropped from 3.2 to 1.3 per day. Nurse medication room trips were reduced by 30% and nurse-reported medication errors fell from a range of 1.2 to 0.8 and 6.3 to 4.0 per month. An innovative human factors framework for nursing worksystem improvement provided practical and high priority targets for interventions that significantly improved the nursing worksystem.

Sound source identification and sound radiation modeling in a moving medium using the time-domain equivalent source method.

PubMed

Zhang, Xiao-Zheng; Bi, Chuan-Xing; Zhang, Yong-Bin; Xu, Liang

2015-05-01

Planar near-field acoustic holography has been successfully extended to reconstruct the sound field in a moving medium, however, the reconstructed field still contains the convection effect that might lead to the wrong identification of sound sources. In order to accurately identify sound sources in a moving medium, a time-domain equivalent source method is developed. In the method, the real source is replaced by a series of time-domain equivalent sources whose strengths are solved iteratively by utilizing the measured pressure and the known convective time-domain Green's function, and time averaging is used to reduce the instability in the iterative solving process. Since these solved equivalent source strengths are independent of the convection effect, they can be used not only to identify sound sources but also to model sound radiations in both moving and static media. Numerical simulations are performed to investigate the influence of noise on the solved equivalent source strengths and the effect of time averaging on reducing the instability, and to demonstrate the advantages of the proposed method on the source identification and sound radiation modeling.

Estimation Accuracy on Execution Time of Run-Time Tasks in a Heterogeneous Distributed Environment

PubMed Central

Liu, Qi; Cai, Weidong; Jin, Dandan; Shen, Jian; Fu, Zhangjie; Liu, Xiaodong; Linge, Nigel

2016-01-01

Distributed Computing has achieved tremendous development since cloud computing was proposed in 2006, and played a vital role promoting rapid growth of data collecting and analysis models, e.g., Internet of things, Cyber-Physical Systems, Big Data Analytics, etc. Hadoop has become a data convergence platform for sensor networks. As one of the core components, MapReduce facilitates allocating, processing and mining of collected large-scale data, where speculative execution strategies help solve straggler problems. However, there is still no efficient solution for accurate estimation on execution time of run-time tasks, which can affect task allocation and distribution in MapReduce. In this paper, task execution data have been collected and employed for the estimation. A two-phase regression (TPR) method is proposed to predict the finishing time of each task accurately. Detailed data of each task have drawn interests with detailed analysis report being made. According to the results, the prediction accuracy of concurrent tasks’ execution time can be improved, in particular for some regular jobs. PMID:27589753

The reduced-risk insecticide azadirachtin poses a toxicological hazard to stingless bee Partamona helleri (Friese, 1900) queens.

PubMed

Bernardes, Rodrigo Cupertino; Barbosa, Wagner Faria; Martins, Gustavo Ferreira; Lima, Maria Augusta Pereira

2018-06-01

Large-scale pesticide application poses a major threat to bee biodiversity by causing a decline in bee populations that, in turn, compromises ecosystem maintenance and agricultural productivity. Biopesticides are considered an alternative to synthetic pesticides with a focus on reducing potential detrimental effects to beneficial organisms such as bees. The production of healthy queen stingless bees is essential for the survival and reproduction of hives, although it remains unknown whether biopesticides influence stingless bee reproduction. In the present study, we investigated the effects of the biopesticide azadirachtin on the survival, behavior, morphology, development, and reproduction of queens of the stingless bee Partamona helleri (Friese, 1900). The neonicotinoid imidacloprid was used as a toxic reference standard. Queens were orally exposed in vitro to a contaminated diet (containing azadirachtin and imidacloprid) during development. Azadirachtin resulted in reduced survival, similarly to imidacloprid, altered development time, caused deformations, and reduced the size of the queens' reproductive organs. All of these factors could potentially compromise colony survival. Results from the present study showed azadirachtin posed a toxicological hazard to P. helleri queens. Copyright © 2018 Elsevier Ltd. All rights reserved.

Thyroid function, reduced kidney function and incident chronic kidney disease in a community-based population: the Atherosclerosis Risk in Communities study.

PubMed

Schultheiss, Ulla T; Daya, Natalie; Grams, Morgan E; Seufert, Jochen; Steffes, Michael; Coresh, Josef; Selvin, Elizabeth; Köttgen, Anna

2017-11-01

Reduced kidney function is a common public health problem that increases risk for a wide variety of adverse outcomes, making the identification of potentially modifiable factors associated with the development of incident chronic kidney disease (CKD) important. Alterations in the hypothalamic-pituitary-thyroid axis have been linked to reduced kidney function, but the association of thyroid function with the development of incident CKD is largely uncharacterized. Concentrations of thyroid stimulating hormone (TSH), free thyroxine (FT4), triiodothyronine (T3) and thyroid peroxidase antibody (TPOAb) were quantified in 12 785 black and white participants of the ongoing community-based prospective Atherosclerosis Risk in Communities study. Thyroid markers and clinical categories of thyroid dysfunction (euthyroidism, combined subclinical and overt hypothyroidism, combined subclinical and overt hyperthyroidism) were also evaluated for their association with reduced kidney function (estimated glomerular filtration rate <60 mL/min/1.73 m2) at study baseline and with incident CKD over a median follow-up time of 19.6 years. Higher TSH and FT4 as well as lower T3 concentrations were strongly and independently associated with reduced kidney function at study baseline. The clinical entities hypothyroidism and hyperthyroidism were also associated with higher odds of baseline reduced kidney function, but this was not significant. However, none of the markers of thyroid function nor different clinical categories of thyroid dysfunction (hypothyroidism, hyperthyroidism or TPOAb positivity) were associated with incident CKD in adjusted analyses. Elevated TSH, FT4 and reduced T3 concentrations were associated with reduced kidney function cross-sectionally. The lack of association with the development of incident CKD suggests that altered thyroid function in the general population is not causally related to CKD development, but screening for thyroidal status may be especially relevant in persons with reduced kidney function. © The Author 2016. Published by Oxford University Press on behalf of ERA-EDTA. All rights reserved.

Methods for determining time of death.

PubMed

Madea, Burkhard

2016-12-01

Medicolegal death time estimation must estimate the time since death reliably. Reliability can only be provided empirically by statistical analysis of errors in field studies. Determining the time since death requires the calculation of measurable data along a time-dependent curve back to the starting point. Various methods are used to estimate the time since death. The current gold standard for death time estimation is a previously established nomogram method based on the two-exponential model of body cooling. Great experimental and practical achievements have been realized using this nomogram method. To reduce the margin of error of the nomogram method, a compound method was developed based on electrical and mechanical excitability of skeletal muscle, pharmacological excitability of the iris, rigor mortis, and postmortem lividity. Further increasing the accuracy of death time estimation involves the development of conditional probability distributions for death time estimation based on the compound method. Although many studies have evaluated chemical methods of death time estimation, such methods play a marginal role in daily forensic practice. However, increased precision of death time estimation has recently been achieved by considering various influencing factors (i.e., preexisting diseases, duration of terminal episode, and ambient temperature). Putrefactive changes may be used for death time estimation in water-immersed bodies. Furthermore, recently developed technologies, such as H magnetic resonance spectroscopy, can be used to quantitatively study decompositional changes. This review addresses the gold standard method of death time estimation in forensic practice and promising technological and scientific developments in the field.

Propulsion Systems Panel

NASA Technical Reports Server (NTRS)

Bianca, Carmelo J.; Miner, Robert; Johnston, Lawrence M.; Bruce, R.; Dennies, Daniel P.; Dickenson, W.; Dreshfield, Robert; Karakulko, Walt; Mcgaw, Mike; Munafo, Paul M.

1993-01-01

Topics addressed are: (1) cryogenic tankage; (2) launch vehicle TPS/insulation; (3) durable passive thermal control devices and/or coatings; (4) development and characterization of processing methods to reduce anisotropy of material properties in Al-Li; (5) durable thermal protection system (TPS); (6) unpressurized Al-Li structures (interstages, thrust structures); (7) near net shape sections; (8) pressurized structures; (9) welding and joining; (10) micrometeoroid and debris hypervelocity shields; (11) state-of-the-art shell buckling structure optimizer program to serve as a rapid design tool; (12) test philosophy; (13) reduced load cycle time; (14) structural analysis methods; (15) optimization of structural criteria; and (16) develop an engineering approach to properly trade material and structural concepts selection, fabrication, facilities, and cost.

Propulsion Systems Panel

NASA Astrophysics Data System (ADS)

Bianca, Carmelo J.; Miner, Robert; Johnston, Lawrence M.; Bruce, R.; Dennies, Daniel P.; Dickenson, W.; Dreshfield, Robert; Karakulko, Walt; McGaw, Mike; Munafo, Paul M.

1993-02-01

Topics addressed are: (1) cryogenic tankage; (2) launch vehicle TPS/insulation; (3) durable passive thermal control devices and/or coatings; (4) development and characterization of processing methods to reduce anisotropy of material properties in Al-Li; (5) durable thermal protection system (TPS); (6) unpressurized Al-Li structures (interstages, thrust structures); (7) near net shape sections; (8) pressurized structures; (9) welding and joining; (10) micrometeoroid and debris hypervelocity shields; (11) state-of-the-art shell buckling structure optimizer program to serve as a rapid design tool; (12) test philosophy; (13) reduced load cycle time; (14) structural analysis methods; (15) optimization of structural criteria; and (16) develop an engineering approach to properly trade material and structural concepts selection, fabrication, facilities, and cost.

Material research for environmental sustainability in Thailand: current trends

PubMed Central

Niranatlumpong, Panadda; Ramangul, Nudjarin; Dulyaprapan, Pongsak; Nivitchanyong, Siriluck; Udomkitdecha, Werasak

2015-01-01

This article covers recent developments of material research in Thailand with a focus on environmental sustainability. Data on Thailand’s consumption and economic growth are briefly discussed to present a relevant snapshot of its economy. A selection of research work is classified into three topics, namely, (a) resource utilization, (b) material engineering and manufacturing, and (c) life cycle efficiency. Material technologies have been developed and implemented to reduce the consumption of materials, energy, and other valuable resources, thus reducing the burden we place on our ecological system. At the same time, product life cycle study allows us to understand the extent of the environmental impact we impart to our planet. PMID:27877788

Hidden Efficiencies: Making Completion of the Pediatric Vaccine Schedule More Efficient for Physicians

PubMed Central

Ciarametaro, Mike; Bradshaw, Steven E.; Guiglotto, Jillian; Hahn, Beth; Meier, Genevieve

2015-01-01

Abstract The objective of this work is to demonstrate the potential time and labor savings that may result from increased use of combination vaccinations. The study (GSK study identifier: HO-12-4735) was a model developed to evaluate the efficiency of the pediatric vaccine schedule, using time and motion studies. The model considered vaccination time and the associated labor costs, but vaccination acquisition costs were not considered. We also did not consider any efficacy or safety differences between formulations. The model inputs were supported by a targeted literature review. The reference year for the model was 2012. The most efficient vaccination program using currently available vaccines was predicted to reduce costs through a combination of fewer injections (62%) and less time per vaccination (38%). The most versus the least efficient vaccine program was predicted to result in a 47% reduction in vaccination time and a 42% reduction in labor and supply costs. The estimated administration cost saving with the most versus the least efficient program was estimated to be nearly US $45 million. If hypothetical 6- or 7-valent vaccines are developed using the already most efficient schedule by adding additional antigens (pneumococcal conjugate vaccine and Haemophilus influenzae type b) to the most efficient 5-valent vaccine, the savings are predicted to be even greater. Combination vaccinations reduce the time burden of the childhood immunization schedule and could create the potential to improve vaccination uptake and compliance as a result of fewer required injections. PMID:25634165

Organo- and nano-catalyst in greener reaction medium: Microwave-assisted expedient synthesis of fine chemicals

EPA Science Inventory

The use of emerging microwave (MW) -assisted chemistry techniques is dramatically reducing chemical waste and reaction times in several organic syntheses and chemical transformations. A brief account of our experiences in developing MW-assisted organic transformations, which invo...

Performance Support Case Studies from IBM.

ERIC Educational Resources Information Center

Duke-Moran, Celia; Swope, Ginger; Morariu, Janis; deKam, Peter

1999-01-01

Presents two case studies that show how IBM addressed performance support solutions and electronic learning. The first developed a performance support and expert coaching solution; the second applied performance support to reducing implementation time and total cost of ownership of enterprise resource planning systems. (Author/LRW)

High-power transmitter automation. [deep space network

NASA Technical Reports Server (NTRS)

Gosline, R.

1980-01-01

The current status of the transmitter automation development applicable to all transmitters in the deep space network is described. Interface and software designs are described that improve reliability and reduce the time required for subsystem turn-on and klystron saturation to less than 10 minutes.

Microwave-Assisted Chemistry: A Rapid and Sustainable Route to Synthesis of Organics and Nanomaterials

EPA Science Inventory

The use of emerging MW-assisted chemistry techniques in conjunction with benign reaction media is dramatically reducing chemical waste and reaction times in several organic syntheses and chemical transformations. This review summarizes recent developments in MW-assisted synthesis...

A strategic approach for prioritizing research and action to prevent suicide.

PubMed

Pringle, Beverly; Colpe, Lisa J; Heinssen, Robert K; Schoenbaum, Michael; Sherrill, Joel T; Claassen, Cynthia A; Pearson, Jane L

2013-01-01

It is time to strategically apply science and accountability to the public health problem of preventable suicide. U.S. suicide rates have remained stable for decades. More than 36,000 individuals now die by suicide each year. A public health-based approach to quickly and substantially reduce suicides requires strategic deployment of existing evidence-based interventions, rapid development of new interventions, and measures to increase accountability for results. The purpose of this Open Forum is to galvanize researchers to further develop and consolidate knowledge needed to guide these actions. As researchers overcome data limitations and methodological challenges, they enable better prioritization of high-risk subgroups for targeted suicide prevention efforts, identification of effective interventions ready for deployment, estimation of the implementation impact of effective interventions in real-world settings, and assessment of time horizons for taking implementation to scale. This new knowledge will permit decision makers to take strategic action to reduce suicide and stakeholders to hold them accountable for results.

Comprehensive Nuclear-Test-Ban Treaty: Background and Current Developments

DTIC Science & Technology

2008-05-28

testing, and has no plans to test. It has reduced the time needed to conduct a nuclear test. Critics raised concerns about the implications of these...particularly as it is reduced, is reliable and safe. So he has not ruled out testing in the future, but there are no plans to do so.’”4 Critics ...Secretary of State, to Honorable Pete Domenici, United States Senate, June 25, 2007. a ten-year-old moratorium on nuclear weapons testing.”5 Another critic

Treatment of elephantiasis of the leg by fasciotomy and lymphangiectomy with skin preservation in a resource-limited setting: a case report and review.

PubMed

Kibadi, K

2018-02-01

The author reports the surgical management of a patient with elephantiasis of the leg in the Democratic Republic of Congo. A fasciotomy and lymphangiectomy with skin preservation, combined with compression therapy, resulted in significant cosmetic, functional, and social improvement. Although challenging in a resource-limited setting, development of surgical management may make it possible to reduce beliefs that elephantiasis is incurable or due to witchcraft and may reduce time to consultation.

Scramjet Combustor Simulations Using Reduced Chemical Kinetics for Practical Fuels

DTIC Science & Technology

2003-12-01

the aerospace industry in reducing prototype and testing costs and the time needed to bring products to market . Accurate simulation of chemical...JP-8 kinetics and soot models into the UNICORN CFD code (Montgomery et al., 2003a) NSF Phase I and II SBIRs for development of a computer-assisted...divided by diameter QSS quasi-steady state REI Reaction Engineering International UNICORN UNsteady Ignition and COmbustion with ReactioNs VULCAN Viscous Upwind aLgorithm for Complex flow ANalysis

Reconfigurable Software for Mission Operations

NASA Technical Reports Server (NTRS)

Trimble, Jay

2014-01-01

We developed software that provides flexibility to mission organizations through modularity and composability. Modularity enables removal and addition of functionality through the installation of plug-ins. Composability enables users to assemble software from pre-built reusable objects, thus reducing or eliminating the walls associated with traditional application architectures and enabling unique combinations of functionality. We have used composable objects to reduce display build time, create workflows, and build scenarios to test concepts for lunar roving operations. The software is open source, and may be downloaded from https:github.comnasamct.

Enzymatic approaches in paper industry for pulp refining and biofilm control.

PubMed

Torres, C E; Negro, C; Fuente, E; Blanco, A

2012-10-01

The use of enzymes has a high potential in the pulp and paper industry to improve the economics of the paper production process and to achieve, at the same time, a reduced environmental impact. Specific enzymes contribute to reduce the amount of chemicals and energy required for the modification of fibers and helps to prevent the formation or development of biofilms. This review is aimed at presenting the latest progresses made in the application of enzymes as refining aids and biofilm control agents.

Should the Australian Army Adopt the Concept of Effects-Based Operations?

DTIC Science & Technology

2003-06-06

militray effect (Echevarria, 2001). 2 John Boyd was a US Air Force Fighter pilot who developed a model of decision making based on his experiences in the...this cycle, the decision maker (initially a fighter pilot ) would try to reduce the time it took him to go through the cycle. The speed of the decision...cycle was relative, but ultimately, the pilot who could reduce his cycle enough to be “inside”‘ his adversary’s cycle would eventually win. The BOYD

Measuring Attention in Rodents: Comparison of a Modified Signal Detection Task and the 5-Choice Serial Reaction Time Task

PubMed Central

Turner, Karly M.; Peak, James; Burne, Thomas H. J.

2016-01-01

Neuropsychiatric research has utilized cognitive testing in rodents to improve our understanding of cognitive deficits and for preclinical drug development. However, more sophisticated cognitive tasks have not been as widely exploited due to low throughput and the extensive training time required. We developed a modified signal detection task (SDT) based on the growing body of literature aimed at improving cognitive testing in rodents. This study directly compares performance on the modified SDT with a traditional test for measuring attention, the 5-choice serial reaction time task (5CSRTT). Adult male Sprague-Dawley rats were trained on either the 5CSRTT or the SDT. Briefly, the 5CSRTT required rodents to pay attention to a spatial array of five apertures and respond with a nose poke when an aperture was illuminated. The SDT required the rat to attend to a light panel and respond either left or right to indicate the presence of a signal. In addition, modifications were made to the reward delivery, timing, control of body positioning, and the self-initiation of trials. It was found that less training time was required for the SDT, with both sessions to criteria and daily session duration significantly reduced. Rats performed with a high level of accuracy (>87%) on both tasks, however omissions were far more frequent on the 5CSRTT. The signal duration was reduced on both tasks as a manipulation of task difficulty relevant to attention and a similar pattern of decreasing accuracy was observed on both tasks. These results demonstrate some of the advantages of the SDT over the traditional 5CSRTT as being higher throughput with reduced training time, fewer omission responses and their body position was controlled at stimulus onset. In addition, rats performing the SDT had comparable high levels of accuracy. These results highlight the differences and similarities between the 5CSRTT and a modified SDT as tools for assessing attention in preclinical animal models. PMID:26834597

Reduction of energy intake using just-in-time feedback from a wearable sensor system.

PubMed

Farooq, Muhammad; McCrory, Megan A; Sazonov, Edward

2017-04-01

This work explored the potential use of a wearable sensor system for providing just-in-time (JIT) feedback on the progression of a meal and tested its ability to reduce the total food mass intake. Eighteen participants consumed three meals each in a lab while monitored by a wearable sensor system capable of accurately tracking chew counts. The baseline visit was used to establish the self-determined ingested mass and the associated chew counts. Real-time feedback on chew counts was provided in the next two visits, during which the target chew count was either the same as that at baseline or the baseline chew count reduced by 25% (in randomized order). The target was concealed from the participant and from the experimenter. Nonparametric repeated-measures ANOVAs were performed to compare mass of intake, meal duration, and ratings of hunger, appetite, and thirst across three meals. JIT feedback targeting a 25% reduction in chew counts resulted in a reduction in mass and energy intake without affecting perceived hunger or fullness. JIT feedback on chewing behavior may reduce intake within a meal. This system can be further used to help develop individualized strategies to provide JIT adaptive interventions for reducing energy intake. © 2017 The Obesity Society.

Super-nodal methods for space-time kinetics

NASA Astrophysics Data System (ADS)

Mertyurek, Ugur

The purpose of this research has been to develop an advanced Super-Nodal method to reduce the run time of 3-D core neutronics models, such as in the NESTLE reactor core simulator and FORMOSA nuclear fuel management optimization codes. Computational performance of the neutronics model is increased by reducing the number of spatial nodes used in the core modeling. However, as the number of spatial nodes decreases, the error in the solution increases. The Super-Nodal method reduces the error associated with the use of coarse nodes in the analyses by providing a new set of cross sections and ADFs (Assembly Discontinuity Factors) for the new nodalization. These so called homogenization parameters are obtained by employing consistent collapsing technique. During this research a new type of singularity, namely "fundamental mode singularity", is addressed in the ANM (Analytical Nodal Method) solution. The "Coordinate Shifting" approach is developed as a method to address this singularity. Also, the "Buckling Shifting" approach is developed as an alternative and more accurate method to address the zero buckling singularity, which is a more common and well known singularity problem in the ANM solution. In the course of addressing the treatment of these singularities, an effort was made to provide better and more robust results from the Super-Nodal method by developing several new methods for determining the transverse leakage and collapsed diffusion coefficient, which generally are the two main approximations in the ANM methodology. Unfortunately, the proposed new transverse leakage and diffusion coefficient approximations failed to provide a consistent improvement to the current methodology. However, improvement in the Super-Nodal solution is achieved by updating the homogenization parameters at several time points during a transient. The update is achieved by employing a refinement technique similar to pin-power reconstruction. A simple error analysis based on the relative residual in the 3-D few group diffusion equation at the fine mesh level is also introduced in this work.

Constellation Program Electrical Ground Support Equipment Research and Development

NASA Technical Reports Server (NTRS)

McCoy, Keegan S.

2010-01-01

At the Kennedy Space Center, I engaged in the research and development of electrical ground support equipment for NASA's Constellation Program. Timing characteristics playa crucial role in ground support communications. Latency and jitter are two problems that must be understood so that communications are timely and consistent within the Kennedy Ground Control System (KGCS). I conducted latency and jitter tests using Alien-Bradley programmable logic controllers (PLCs) so that these two intrinsic network properties can be reduced. Time stamping and clock synchronization also play significant roles in launch processing and operations. Using RSLogix 5000 project files and Wireshark network protocol analyzing software, I verified master/slave PLC Ethernet module clock synchronization, master/slave IEEE 1588 communications, and time stamping capabilities. All of the timing and synchronization test results are useful in assessing the current KGCS operational level and determining improvements for the future.

Algorithms and analyses for stochastic optimization for turbofan noise reduction using parallel reduced-order modeling

NASA Astrophysics Data System (ADS)

Yang, Huanhuan; Gunzburger, Max

2017-06-01

Simulation-based optimization of acoustic liner design in a turbofan engine nacelle for noise reduction purposes can dramatically reduce the cost and time needed for experimental designs. Because uncertainties are inevitable in the design process, a stochastic optimization algorithm is posed based on the conditional value-at-risk measure so that an ideal acoustic liner impedance is determined that is robust in the presence of uncertainties. A parallel reduced-order modeling framework is developed that dramatically improves the computational efficiency of the stochastic optimization solver for a realistic nacelle geometry. The reduced stochastic optimization solver takes less than 500 seconds to execute. In addition, well-posedness and finite element error analyses of the state system and optimization problem are provided.

Microfabricated valveless devices for thermal bioreactions based on diffusion-limited evaporation.

PubMed

Wang, Fang; Yang, Ming; Burns, Mark A

2008-01-01

Microfluidic devices that reduce evaporative loss during thermal bioreactions such as PCR without microvalves have been developed by relying on the principle of diffusion-limited evaporation. Both theoretical and experimental results demonstrate that the sample evaporative loss can be reduced by more than 20 times using long narrow diffusion channels on both sides of the reaction region. In order to further suppress the evaporation, the driving force for liquid evaporation is reduced by two additional techniques: decreasing the interfacial temperature using thermal isolation and reducing the vapor concentration gradient by replenishing water vapor in the diffusion channels. Both thermal isolation and vapor replenishment techniques can limit the sample evaporative loss to approximately 1% of the reaction content.

An asymptotic unsteady lifting-line theory with energetics and optimum motion of thrust-producing lifting surfaces. Thesis

NASA Technical Reports Server (NTRS)

Ahmadi, A. R.

1981-01-01

A low frequency unsteady lifting-line theory is developed for a harmonically oscillating wing of large aspect ratio. The wing is assumed to be chordwise rigid but completely flexible in the span direction. The theory is developed by use of the method of matched asymptotic expansions which reduces the problem from a singular integral equation to quadrature. The wing displacements are prescribed and the pressure field, airloads, and unsteady induced downwash are obtained in closed form. The influence of reduced frequency, aspect ratio, planform shape, and mode of oscillation on wing aerodynamics is demonstrated through numerical examples. Compared with lifting-surface theory, computation time is reduced significantly. Using the present theory, the energetic quantities associated with the propulsive performance of a finite wing oscillating in combined pitch and heave are obtained in closed form. Numerical examples are presented for an elliptic wing.

Biocompatible low Young's modulus achieved by strong crystallographic elastic anisotropy in Ti-15Mo-5Zr-3Al alloy single crystal.

PubMed

Lee, S-H; Todai, M; Tane, M; Hagihara, K; Nakajima, H; Nakano, T

2012-10-01

The elastic anisotropy of the Ti-15Mo-5Zr-3Al (mass%) β-Ti alloy, an ISO certified biomedical material, was investigated using its single crystal. It was revealed that the Young's modulus exhibited pronounced anisotropy. The Young's modulus was reduced to 44.4GPa along the 〈100〉 direction in the Ti-15Mo-5Zr-3Al single crystal, that is comparable to that of human cortical bones. We determined the strategy that β-Ti alloys with extremely low moduli can be developed by reducing the electron-atom (e/a) ratio in alloys, and by suppressing the formation of the ω-phase at the same time. This new knowledge must lead to the development of "single crystalline β-Ti implant materials" as hard tissue replacements for reducing the stress shielding effect. Copyright © 2012 Elsevier Ltd. All rights reserved.

Optimal charge control strategies for stationary photovoltaic battery systems

NASA Astrophysics Data System (ADS)

Li, Jiahao; Danzer, Michael A.

2014-07-01

Battery systems coupled to photovoltaic (PV) modules for example fulfill one major function: they locally decouple PV generation and consumption of electrical power leading to two major effects. First, they reduce the grid load, especially at peak times and therewith reduce the necessity of a network expansion. And second, they increase the self-consumption in households and therewith help to reduce energy expenses. For the management of PV batteries charge control strategies need to be developed to reach the goals of both the distribution system operators and the local power producer. In this work optimal control strategies regarding various optimization goals are developed on the basis of the predicted household loads and PV generation profiles using the method of dynamic programming. The resulting charge curves are compared and essential differences discussed. Finally, a multi-objective optimization shows that charge control strategies can be derived that take all optimization goals into account.

Reducing overlay sampling for APC-based correction per exposure by replacing measured data with computational prediction

NASA Astrophysics Data System (ADS)

Noyes, Ben F.; Mokaberi, Babak; Oh, Jong Hun; Kim, Hyun Sik; Sung, Jun Ha; Kea, Marc

2016-03-01

One of the keys to successful mass production of sub-20nm nodes in the semiconductor industry is the development of an overlay correction strategy that can meet specifications, reduce the number of layers that require dedicated chuck overlay, and minimize measurement time. Three important aspects of this strategy are: correction per exposure (CPE), integrated metrology (IM), and the prioritization of automated correction over manual subrecipes. The first and third aspects are accomplished through an APC system that uses measurements from production lots to generate CPE corrections that are dynamically applied to future lots. The drawback of this method is that production overlay sampling must be extremely high in order to provide the system with enough data to generate CPE. That drawback makes IM particularly difficult because of the throughput impact that can be created on expensive bottleneck photolithography process tools. The goal is to realize the cycle time and feedback benefits of IM coupled with the enhanced overlay correction capability of automated CPE without impacting process tool throughput. This paper will discuss the development of a system that sends measured data with reduced sampling via an optimized layout to the exposure tool's computational modelling platform to predict and create "upsampled" overlay data in a customizable output layout that is compatible with the fab user CPE APC system. The result is dynamic CPE without the burden of extensive measurement time, which leads to increased utilization of IM.

Elements of Designing for Cost

NASA Technical Reports Server (NTRS)

Dean, Edwin B.; Unal, Resit

1992-01-01

During recent history in the United States, government systems development has been performance driven. As a result, systems within a class have experienced exponentially increasing cost over time in fixed year dollars. Moreover, little emphasis has been placed on reducing cost. This paper defines designing for cost and presents several tools which, if used in the engineering process, offer the promise of reducing cost. Although other potential tools exist for designing for cost, this paper focuses on rules of thumb, quality function deployment, Taguchi methods, concurrent engineering, and activity based costing. Each of these tools has been demonstrated to reduce cost if used within the engineering process.

Viscous damped space structure for reduced jitter

NASA Technical Reports Server (NTRS)

Wilson, James F.; Davis, L. Porter

1987-01-01

A technique to provide modal vibration damping in high performance space structures was developed which uses less than one once of incompressible fluid. Up to 50 percent damping can be achieved which can reduce the settling times of the lowest structural mode by as much as 50 to 1. This concept allows the designers to reduce the weight of the structure while improving its dynamic performance. Damping by this technique is purely viscous and has been shown by test to be linear over 5 orders of input magnitude. Amplitudes as low as 0.2 microinch were demonstrated. Damping in the system is independent of stiffness and relatively insensitive to temperature.

Noise Mitigation During Pile Driving Efficiently Reduces Disturbance of Marine Mammals.

PubMed

Nehls, Georg; Rose, Armin; Diederichs, Ansgar; Bellmann, Michael; Pehlke, Hendrik

2016-01-01

Acoustic monitoring of harbor porpoises (Phocoena phocoena L., 1758) indicated a strongly reduced disturbance by noise emitted by pile driving for offshore wind turbine foundations insulated by a big bubble curtain (BBC). This newly developed noise mitigation system was tested during construction of the offshore wind farm Borkum West II (North Sea). Because porpoise activity strongly corresponded to the sound level, operation of the new system under its most suitable configuration reduced the porpoise disturbance area by ~90%. Hence, for the first time, a positive effect of a noise mitigation system during offshore pile driving on an affected marine mammal species could be demonstrated.

Elements of designing for cost

NASA Technical Reports Server (NTRS)

Dean, Edwin B.; Unal, Resit

1992-01-01

During recent history in the United States, government systems development has been performance driven. As a result, systems within a class have experienced exponentially increasing cost over time in fixed year dollars. Moreover, little emphasis has been placed on reducing cost. This paper defines designing for cost and presents several tools which, if used in the engineering process, offer the promise of reducing cost. Although other potential tools exist for designing for cost, this paper focuses on rules of thumb, quality function deployment, Taguchi methods, concurrent engineering, and activity-based costing. Each of these tools has been demonstrated to reduce cost if used within the engineering process.

An iterative reduced field-of-view reconstruction for periodically rotated overlapping parallel lines with enhanced reconstruction (PROPELLER) MRI.

PubMed

Lin, Jyh-Miin; Patterson, Andrew J; Chang, Hing-Chiu; Gillard, Jonathan H; Graves, Martin J

2015-10-01

To propose a new reduced field-of-view (rFOV) strategy for iterative reconstructions in a clinical environment. Iterative reconstructions can incorporate regularization terms to improve the image quality of periodically rotated overlapping parallel lines with enhanced reconstruction (PROPELLER) MRI. However, the large amount of calculations required for full FOV iterative reconstructions has posed a huge computational challenge for clinical usage. By subdividing the entire problem into smaller rFOVs, the iterative reconstruction can be accelerated on a desktop with a single graphic processing unit (GPU). This rFOV strategy divides the iterative reconstruction into blocks, based on the block-diagonal dominant structure. A near real-time reconstruction system was developed for the clinical MR unit, and parallel computing was implemented using the object-oriented model. In addition, the Toeplitz method was implemented on the GPU to reduce the time required for full interpolation. Using the data acquired from the PROPELLER MRI, the reconstructed images were then saved in the digital imaging and communications in medicine format. The proposed rFOV reconstruction reduced the gridding time by 97%, as the total iteration time was 3 s even with multiple processes running. A phantom study showed that the structure similarity index for rFOV reconstruction was statistically superior to conventional density compensation (p < 0.001). In vivo study validated the increased signal-to-noise ratio, which is over four times higher than with density compensation. Image sharpness index was improved using the regularized reconstruction implemented. The rFOV strategy permits near real-time iterative reconstruction to improve the image quality of PROPELLER images. Substantial improvements in image quality metrics were validated in the experiments. The concept of rFOV reconstruction may potentially be applied to other kinds of iterative reconstructions for shortened reconstruction duration.

Using operations research to plan improvement of the transport of critically ill patients.

PubMed

Chen, Jing; Awasthi, Anjali; Shechter, Steven; Atkins, Derek; Lemke, Linda; Fisher, Les; Dodek, Peter

2013-01-01

Operations research is the application of mathematical modeling, statistical analysis, and mathematical optimization to understand and improve processes in organizations. The objective of this study was to illustrate how the methods of operations research can be used to identify opportunities to reduce the absolute value and variability of interfacility transport intervals for critically ill patients. After linking data from two patient transport organizations in British Columbia, Canada, for all critical care transports during the calendar year 2006, the steps for transfer of critically ill patients were tabulated into a series of time intervals. Statistical modeling, root-cause analysis, Monte Carlo simulation, and sensitivity analysis were used to test the effect of changes in component intervals on overall duration and variation of transport times. Based on quality improvement principles, we focused on reducing the 75th percentile and standard deviation of these intervals. We analyzed a total of 3808 ground and air transports. Constraining time spent by transport personnel at sending and receiving hospitals was projected to reduce the total time taken by 33 minutes with as much as a 20% reduction in standard deviation of these transport intervals in 75% of ground transfers. Enforcing a policy of requiring acceptance of patients who have life- or limb-threatening conditions or organ failure was projected to reduce the standard deviation of air transport time by 63 minutes and the standard deviation of ground transport time by 68 minutes. Based on findings from our analyses, we developed recommendations for technology renovation, personnel training, system improvement, and policy enforcement. Use of the tools of operations research identifies opportunities for improvement in a complex system of critical care transport.

Parameterized reduced order models from a single mesh using hyper-dual numbers

NASA Astrophysics Data System (ADS)

Brake, M. R. W.; Fike, J. A.; Topping, S. D.

2016-06-01

In order to assess the predicted performance of a manufactured system, analysts must consider random variations (both geometric and material) in the development of a model, instead of a single deterministic model of an idealized geometry with idealized material properties. The incorporation of random geometric variations, however, potentially could necessitate the development of thousands of nearly identical solid geometries that must be meshed and separately analyzed, which would require an impractical number of man-hours to complete. This research advances a recent approach to uncertainty quantification by developing parameterized reduced order models. These parameterizations are based upon Taylor series expansions of the system's matrices about the ideal geometry, and a component mode synthesis representation for each linear substructure is used to form an efficient basis with which to study the system. The numerical derivatives required for the Taylor series expansions are obtained via hyper-dual numbers, and are compared to parameterized models constructed with finite difference formulations. The advantage of using hyper-dual numbers is two-fold: accuracy of the derivatives to machine precision, and the need to only generate a single mesh of the system of interest. The theory is applied to a stepped beam system in order to demonstrate proof of concept. The results demonstrate that the hyper-dual number multivariate parameterization of geometric variations, which largely are neglected in the literature, are accurate for both sensitivity and optimization studies. As model and mesh generation can constitute the greatest expense of time in analyzing a system, the foundation to create a parameterized reduced order model based off of a single mesh is expected to reduce dramatically the necessary time to analyze multiple realizations of a component's possible geometry.

Developmental instability: measures of resistance and resilience using pumpkin (Cucurbita pepo L.)

USGS Publications Warehouse

Freeman, D. Carl; Brown, Michelle L.; Dobson, Melissa; Jordan, Yolanda; Kizy, Anne; Micallef, Chris; Hancock, Leandria C.; Graham, John H.; Emlen, John M.

2003-01-01

Fluctuating asymmetry measures random deviations from bilateral symmetry, and thus estimates developmental instability, the loss of ability by an organism to regulate its development. There have been few rigorous tests of this proposition. Regulation of bilateral symmetry must involve either feedback between the sides or independent regulation toward a symmetric set point. Either kind of regulation should decrease asymmetry over time, but only right–left feedback produces compensatory growth across sides, seen as antipersistent growth following perturbation. Here, we describe the developmental trajectories of perturbed and unperturbed leaves of pumpkin, Cucurbita pepoL., grown at three densities. Covering one side of a leaf with aluminium foil for 24 h perturbed leaf growth. Reduced growth on the perturbed side caused leaves to become more asymmetrical than unperturbed controls. After the treatment the size-corrected asymmetry decreased over time. In addition, rescaled range analysis showed that asymmetry was antipersistent rather than random, i.e. fluctuation in one direction was likely to be followed by fluctuations in the opposite direction. Development involves right–left feedback. This feedback reduced size-corrected asymmetry over time most strongly in the lowest density treatment suggesting that developmental instability results from a lack of resilience rather than resistance. 

Guidance and control requirements for high-speed Rollout and Turnoff (ROTO)

NASA Technical Reports Server (NTRS)

Goldthorpe, Steve H.; Kernik, Alan C.; Mcbee, Larry S.; Preston, Orv W.

1995-01-01

This report defines the initial requirements for designing a research high-speed rollout and turnoff (ROTO) guidance and control system applicable to transport class aircraft whose purpose is to reduce the average runway occupancy time (ROT) for aircraft operations. The requirements will be used to develop a ROTO system for both automatic and manual piloted operation under normal and reduced visibility conditions. Requirements were determined for nose wheel/rudder steering, braking/reverse thrust, and the navigation system with the aid of a non-real time, three degree-of-freedom MD-11 simulation program incorporating airframe and gear dynamics. The requirements were developed for speeds up to 70 knots using 30 ft exit geometries under dry and wet surface conditions. The requirements were generated under the assumptions that the aircraft landing system meets the current Category III touchdown dispersion requirements and that aircraft interarrival spacing is 2 nautical miles. This effort determined that auto-asymmetric braking is needed to assist steering for aft center-of-gravity aircraft. This report shows various time-history plots of the aircraft performance for the ROTO operation. This effort also investigated the state-of-the-art in the measurement of the runway coefficient of friction for various runway conditions.

Customer Communication Challenges and Solutions in Globally Distributed Agile Software Development

NASA Astrophysics Data System (ADS)

Pikkarainen, Minna; Korkala, Mikko

Working in the globally distributed market is one of the key trends among the software organizations all over the world. [1-5]. Several factors have contributed to the growth of distributed software development; time-zone independent ”follow the sun” development, access to well-educated labour, maturation of the technical infrastructure and reduced costs are some of the most commonly cited benefits of distributed development [3, 6-8]. Furthermore, customers are often located in different countries because of the companies’ internationalization purposes or good market opportunities.

Smart command recognizer (SCR) - For development, test, and implementation of speech commands

NASA Technical Reports Server (NTRS)

Simpson, Carol A.; Bunnell, John W.; Krones, Robert R.

1988-01-01

The SCR, a rapid prototyping system for the development, testing, and implementation of speech commands in a flight simulator or test aircraft, is described. A single unit performs all functions needed during these three phases of system development, while the use of common software and speech command data structure files greatly reduces the preparation time for successive development phases. As a smart peripheral to a simulation or flight host computer, the SCR interprets the pilot's spoken input and passes command codes to the simulation or flight computer.

Software handlers for process interfaces

NASA Technical Reports Server (NTRS)

Bercaw, R. W.

1976-01-01

Process interfaces are developed in an effort to reduce the time, effort, and money required to install computer systems. Probably the chief obstacle to the achievement of these goals lies in the problem of developing software handlers having the same degree of generality and modularity as the hardware. The problem of combining the advantages of modular instrumentation with those of modern multitask operating systems has not been completely solved, but there are a number of promising developments. The essential principles involved are considered.

Recent developments in photovoltaic energy by ERDA/NASA-LeRC

NASA Technical Reports Server (NTRS)

Deyo, J. N.

1977-01-01

Application development activities were designed to stimulate the market for photovoltaics so that as costs are reduced there will be an increasing market demand to encourage the expansion of industrial solar array production capacity. Supporting these application development activities are tasks concerned with: (1) establishing standards and methodology for terrestrial solar cell calibration; (2) conducting standard and diagnostic measurements on solar cells and modules; and (3) conducting real time and accelerated testing of solar cell modules and materials of construction under outdoor sunlight conditions.

A collaborative computing framework of cloud network and WBSN applied to fall detection and 3-D motion reconstruction.

PubMed

Lai, Chin-Feng; Chen, Min; Pan, Jeng-Shyang; Youn, Chan-Hyun; Chao, Han-Chieh

2014-03-01

As cloud computing and wireless body sensor network technologies become gradually developed, ubiquitous healthcare services prevent accidents instantly and effectively, as well as provides relevant information to reduce related processing time and cost. This study proposes a co-processing intermediary framework integrated cloud and wireless body sensor networks, which is mainly applied to fall detection and 3-D motion reconstruction. In this study, the main focuses includes distributed computing and resource allocation of processing sensing data over the computing architecture, network conditions and performance evaluation. Through this framework, the transmissions and computing time of sensing data are reduced to enhance overall performance for the services of fall events detection and 3-D motion reconstruction.

Using simulation in out-patient queues: a case study.

PubMed

Huarng, F; Lee, M H

1996-01-01

Overwork and overcrowding in some periods was an important issue for the out-patient department of a local hospital in Chia-Yi in Taiwan. The hospital administrators wanted to manage the patient flow effectively. Describes a study which focused on the utilization of doctors and staff in the out-patient department, the time spent in the hospital by an out-patient, and the length of the out-patient queue. Explains how a computer simulation model was developed to study how changes in the appointment system, staffing policies and service units would affect the observed bottleneck. The results show that the waiting time was greatly reduced and the workload of the doctor was also reduced to a reasonable rate in the overwork and overcrowding periods.

Tighten water-chemistry control after boiler layup

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brestel, L.

1994-01-01

The potential for internal deposition and corrosion can affect boiler reliability by reducing thermal efficiency, tube integrity, and the time between chemical cleanings. While chemical control specifications for normal operation have been developed by consensus of manufacturers and industry, their impact on shutdowns, layups, and startups is not always appreciated. The discussion of chemical-control options applies to boiler systems operating in the medium- and high-pressure ranges. Identification and correction of root causes underlying the chemistry problems encountered and application of the principles involved should result in shorter startup times, improved control over phosphate hideout, and reduced need for chemical cleaning.more » Each of these has a significant cost impact; together, they are the true measure of a successful chemistry-control program.« less

New protocol for construction of eyeglasses-supported provisional nasal prosthesis using CAD/CAM techniques.

PubMed

Ciocca, Leonardo; Fantini, Massimiliano; De Crescenzio, Francesca; Persiani, Franco; Scotti, Roberto

2010-01-01

A new protocol for making an immediate provisional eyeglasses-supported nasal prosthesis is presented that uses laser scanning, computer-aided design/computer-aided manufacturing procedures, and rapid prototyping techniques, reducing time and costs while increasing the quality of the final product. With this protocol, the eyeglasses were digitized, and the relative position of the nasal prosthesis was planned and evaluated in a virtual environment without any try-in appointment. This innovative method saves time, reduces costs, and restores the patient's aesthetic appearance after a disfiguration caused by ablation of the nasal pyramid better than conventional restoration methods. Moreover, the digital model of the designed nasal epithesis can be used to develop a definitive prosthesis anchored to osseointegrated craniofacial implants.

Development of the Oriental Latrine Fly, Chrysomya megacephala (Diptera: Calliphoridae), at Five Constant Temperatures.

PubMed

Gruner, S V; Slone, D H; Capinera, J L; Turco, M P

2017-03-01

Chrysomya megacephala (Fabricius) is a forensically important fly that is found throughout the tropics and subtropics. We calculated the accumulated development time and transition points for each life stage from eclosion to adult emergence at five constant temperatures: 15, 20, 25, 30, and 35 °C. For each transition, the 10th, 50th, and 90th percentiles were calculated with a logistic linear model. The mean transition times and % survivorship were determined directly from the raw laboratory data. Development times of C. megacephala were compared with that of two other closely related species, Chrysomya rufifacies (Macquart) and Phormia regina (Meigen). Ambient and larval mass temperatures were collected from field studies conducted from 2001-2004. Field study data indicated that adult fly activity was reduced at lower ambient temperatures, but once a larval mass was established, heat generation occurred. These development times and durations can be used for estimation of a postmortem interval (PMI). © The Authors 2016. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Are There Racial-Ethnic Disparities in Time to Pressure Ulcer Development and Pressure Ulcer Treatment in Older Adults After Nursing Home Admission?

PubMed Central

Bliss, Donna Z.; Gurvich, Olga; Savik, Kay; Eberly, Lynn E.; Harms, Susan; Mueller, Christine; Wyman, Jean F.; Garrard, Judith; Virnig, Beth

2017-01-01

Objective The objective of this study was to assess whether there are racial and ethnic disparities in the time to development of a pressure ulcer and number of pressure ulcer treatments in individuals aged 65 and older after nursing home admission. Method Multi-level predictors of time to a pressure ulcer from three national surveys were analyzed using Cox proportional hazards regression for White Non-Hispanic residents. Using the Peters–Belson method to assess for disparities, estimates from the regression models were applied to American Indians/Alaskan Natives, Asians/ Pacific Islanders, Blacks, and Hispanics separately resulting in estimates of expected outcomes as if they were White Non-Hispanic, and were then compared with their observed outcomes. Results More Blacks developed pressure ulcers sooner than expected. No disparities in time to a pressure ulcer disadvantaging other racial/ethnic groups were found. There were no disparities in pressure ulcer treatment for any group. Discussion Reducing disparities in pressure ulcer development offers a strategy to improve the quality of nursing home care. PMID:25260648

Are there racial-ethnic disparities in time to pressure ulcer development and pressure ulcer treatment in older adults after nursing home admission?

PubMed

Bliss, Donna Z; Gurvich, Olga; Savik, Kay; Eberly, Lynn E; Harms, Susan; Mueller, Christine; Wyman, Jean F; Garrard, Judith; Virnig, Beth

2015-06-01

The objective of this study was to assess whether there are racial and ethnic disparities in the time to development of a pressure ulcer and number of pressure ulcer treatments in individuals aged 65 and older after nursing home admission. Multi-level predictors of time to a pressure ulcer from three national surveys were analyzed using Cox proportional hazards regression for White Non-Hispanic residents. Using the Peters-Belson method to assess for disparities, estimates from the regression models were applied to American Indians/Alaskan Natives, Asians/Pacific Islanders, Blacks, and Hispanics separately resulting in estimates of expected outcomes as if they were White Non-Hispanic, and were then compared with their observed outcomes. More Blacks developed pressure ulcers sooner than expected. No disparities in time to a pressure ulcer disadvantaging other racial/ethnic groups were found. There were no disparities in pressure ulcer treatment for any group. Reducing disparities in pressure ulcer development offers a strategy to improve the quality of nursing home care. © The Author(s) 2014.

Mediators of the Development and Prevention of Violent Behavior

PubMed Central

Morgan-Lopez, Antonio A.; Howard, Terry-Lee; Browne, Dorothy C.; Flay, Brian R.

2008-01-01

The purpose of this investigation was to determine if the Aban Aya Youth Project, a culturally grounded intervention, produced differences in changes over time in core intervening variables (i.e., communal value orientation, empathy, violence avoidance efficacy beliefs) and whether these variables mediated intervention effects on the development of youth violent behavior. Fifth grade cohorts at 12 schools were randomly assigned to one of two intervention conditions or an attention placebo control condition and followed longitudinally through eighth grade. A total of 668 students (49% male) participated in the study. Mediation analyses suggested that both program conditions (as compared to the control condition) led to steeper increases over time in empathy which, in turn were related to reductions in the likelihood of violent behavior over time. No other significant program effects were detected, although changes over time in violence avoidance efficacy were associated with reduced likelihood of violent behavior. Findings are discussed in terms of theory development, program development and points of refinement of the Aban Aya Youth Project and implications for future research. PMID:17558552

Reducing the risk of rear-end collisions with infrastructure-to-vehicle (I2V) integration of variable speed limit control and adaptive cruise control system.

PubMed

Li, Ye; Wang, Hao; Wang, Wei; Liu, Shanwen; Xiang, Yun

2016-08-17

Adaptive cruise control (ACC) has been investigated recently to explore ways to increase traffic capacity, stabilize traffic flow, and improve traffic safety. However, researchers seldom have studied the integration of ACC and roadside control methods such as the variable speed limit (VSL) to improve safety. The primary objective of this study was to develop an infrastructure-to-vehicle (I2V) integrated system that incorporated both ACC and VSL to reduce rear-end collision risks on freeways. The intelligent driver model was firstly modified to simulate ACC behavior and then the VSL strategy used in this article was introduced. Next, the I2V system was proposed to integrate the 2 advanced techniques, ACC and VSL. Four scenarios of no control, VSL only, ACC only, and the I2V system were tested in simulation experiments. Time exposed time to collision (TET) and time integrated time to collision (TIT), 2 surrogate safety measures derived from time to collision (TTC), were used to evaluate safety issues associated with rear-end collisions. The total travel times of each scenario were also compared. The simulation results indicated that both the VSL-only and ACC-only methods had a positive impact on reducing the TET and TIT values (reduced by 53.0 and 58.6% and 59.0 and 65.3%, respectively). The I2V system combined the advantages of both ACC and VSL to achieve the most safety benefits (reduced by 71.5 and 77.3%, respectively). Sensitivity analysis of the TTC threshold also showed that the I2V system obtained the largest safety benefits with all of the TTC threshold values. The impact of different market penetration rates of ACC vehicles in I2V system indicated that safety benefits increase with an increase in ACC proportions. Compared to VSL-only and ACC-only scenarios, this integrated I2V system is more effective in reducing rear-end collision risks. The findings of this study provide useful information for traffic agencies to implement novel techniques to improve safety on freeways.

DOE Office of Scientific and Technical Information (OSTI.GOV)

S.K. Kawatra; B. Anamerie; T.C. Eisele

The pig iron nugget process was developed as an alternative to the traditional blast furnace process by Kobe Steel. The process aimed to produce pig iron nuggets, which have similar chemical and physical properties to blast furnace pig iron, in a single step. The pig iron nugget process utilizes coal instead of coke and self reducing and fluxing dried green balls instead of pellets and sinters. In this process the environmental emissions caused by coke and sinter production, and energy lost between pellet induration (heat hardening) and transportation to the blast furnace can be eliminated. The objectives of this researchmore » were to (1) produce pig iron nuggets in the laboratory, (2) characterize the pig iron nugget produced and compare them with blast furnace pig iron, (3) investigate the furnace temperature and residence time effects on the pig iron nugget production, and (4) optimize the operational furnace temperatures and residence times. The experiments involved heat treatment of self reducing and fluxing dried green balls at various furnace temperatures and residence times. Three chemically and physically different products were produced after the compete reduction of iron oxides to iron depending on the operational furnace temperatures and/or residence times. These products were direct reduced iron (DRI), transition direct reduced iron (TDRI), and pig iron nuggets. The increase in the carbon content of the system as a function of furnace temperature and/or residence time dictated the formation of these products. The direct reduced iron, transition direct reduced iron, and pig iron nuggets produced were analyzed for their chemical composition, degree of metallization, apparent density, microstructure and microhardness. In addition, the change in the carbon content of the system with the changing furnace temperature and/or residence time was detected by optical microscopy and Microhardness measurements. The sufficient carbon dissolution required for the production of pig iron nuggets was determined. It was determined that pig iron nuggets produced had a high apparent density (6.7-7.2 gr/cm3), highly metallized, slag free structure, high iron content (95-97%), high microhardness values (> 325 HVN) and microstructure similar to white cast iron. These properties made them a competitive alternative to blast furnace pig iron.« less

Development and testing of a CW-EPR apparatus for imaging of short-lifetime nitroxyl radicals in mouse head

NASA Astrophysics Data System (ADS)

Sato-Akaba, Hideo; Fujii, Hirotada; Hirata, Hiroshi

2008-08-01

This article describes a method for reducing the acquisition time in three-dimensional (3D) continuous-wave electron paramagnetic resonance (CW-EPR) imaging. To visualize nitroxyl spin probes, which have a short lifetime in living organisms, the acquisition time for a data set of spectral projections should be shorter than the lifetime of the spin probes. To decrease the total time required for data acquisition, the duration of magnetic field scanning was reduced to 0.5 s. Moreover, the number of projections was decreased by using the concept of a uniform distribution. To demonstrate this faster data acquisition, two kinds of nitroxyl radicals with different decay rates were measured in mice. 3D EPR imaging of 4-hydroxy-2,2,6,6-tetramethylpiperidine-d 17-1- 15N-1-oxyl in mouse head was successfully carried out. 3D EPR imaging of nitroxyl spin probes with a half-life of a few minutes was achieved for the first time in live animals.