Science.gov

Sample records for reference commercial-scale nuclear-driven

  1. Optimized Flow Sheet for a Reference Commercial-Scale Nuclear-Driven High-Temperature Electrolysis Hydrogen Production Plant

    SciTech Connect

    M. G. McKellar; J. E. O'Brien; E. A. Harvego; J. S. Herring

    2007-11-01

    This report presents results from the development and optimization of a reference commercialscale high-temperature electrolysis (HTE) plant for hydrogen production. The reference plant design is driven by a high-temperature helium-cooled reactor coupled to a direct Brayton power cycle. The reference design reactor power is 600 MWt, with a primary system pressure of 7.0 MPa, and reactor inlet and outlet fluid temperatures of 540° C and 900°C, respectively. The electrolysis unit used to produce hydrogen consists of 4.176 × 10 6 cells with a per-cell active area of 225 cm2. A nominal cell area-specific resistance, ASR, value of 0.4 Ohm•cm2 with a current density of 0.25 A/cm2 was used, and isothermal boundary conditions were assumed. The optimized design for the reference hydrogen production plant operates at a system pressure of 5.0 MPa, and utilizes an air-sweep system to remove the excess oxygen that is evolved on the anode side of the electrolyzer. The inlet air for the air-sweep system is compressed to the system operating pressure of 5.0 MPa in a four-stage compressor with intercooling. The overall system thermal-to-hydrogen production efficiency (based on the low heating value of the produced hydrogen) is 49.07% at a hydrogen production rate of 2.45 kg/s with the high-temperature helium-cooled reactor concept. The information presented in this report is intended to establish an optimized design for the reference nuclear-driven HTE hydrogen production plant so that parameters can be compared with other hydrogen production methods and power cycles to evaluate relative performance characteristics and plant economics.

  2. Analysis of Improved Reference Design for a Nuclear-Driven High Temperature Electrolysis Hydrogen Production Plant

    SciTech Connect

    Edwin A. Harvego; James E. O'Brien; Michael G. McKellar

    2010-06-01

    The use of High Temperature Electrolysis (HTE) for the efficient production of hydrogen without the greenhouse gas emissions associated with conventional fossil-fuel hydrogen production techniques has been under investigation at the Idaho National Engineering Laboratory (INL) for the last several years. The activities at the INL have included the development, testing and analysis of large numbers of solid oxide electrolysis cells, and the analyses of potential plant designs for large scale production of hydrogen using an advanced Very-High Temperature Reactor (VHTR) to provide the process heat and electricity to drive the electrolysis process. The results of these system analyses, using the UniSim process analysis software, have shown that the HTE process, when coupled to a VHTR capable of operating at reactor outlet temperatures of 800 °C to 950 °C, has the potential to produce the large quantities of hydrogen needed to meet future energy and transportation needs with hydrogen production efficiencies in excess of 50%. In addition, economic analyses performed on the INL reference plant design, optimized to maximize the hydrogen production rate for a 600 MWt VHTR, have shown that a large nuclear-driven HTE hydrogen production plant can to be economically competitive with conventional hydrogen production processes, particularly when the penalties associated with greenhouse gas emissions are considered. The results of this research led to the selection in 2009 of HTE as the preferred concept in the U.S. Department of Energy (DOE) hydrogen technology down-selection process. However, the down-selection process, along with continued technical assessments at the INL, has resulted in a number of proposed modifications and refinements to improve the original INL reference HTE design. These modifications include changes in plant configuration, operating conditions and individual component designs. This paper describes the resulting new INL reference design and presents

  3. Economic Analysis of the Reference Design for a Nuclear-Driven High-Temperature-Electrolysis Hydrogen Production Plant

    SciTech Connect

    E. A. Harvego; M. G. McKellar; M. S. Sohal; J. E. O'Brien; J. S. Herring

    2008-01-01

    A reference design for a commercial-scale high-temperature electrolysis (HTE) plant for hydrogen production was developed to provide a basis for comparing the HTE concept with other hydrogen production concepts. The reference plant design is driven by a high-temperature helium-cooled reactor coupled to a direct Brayton power cycle. The reference design reactor power is 600 MWt, with a primary system pressure of 7.0 MPa, and reactor inlet and outlet fluid temperatures of 540°C and 900°C, respectively. The electrolysis unit used to produce hydrogen consists of 4,009,177 cells with a per-cell active area of 225 cm2. A nominal cell area-specific resistance, ASR, value of 0.4 Ohm•cm2 with a current density of 0.25 A/cm2 was used, and isothermal boundary conditions were assumed. The optimized design for the reference hydrogen production plant operates at a system pressure of 5.0 MPa, and utilizes an air-sweep system to remove the excess oxygen that is evolved on the anode side of the electrolyzer. The inlet air for the air-sweep system is compressed to the system operating pressure of 5.0 MPa in a four-stage compressor with intercooling. The alternating current, AC, to direct current, DC, conversion is 96%. The overall system thermal-to-hydrogen production efficiency (based on the low heating value of the produced hydrogen) is 47.12% at a hydrogen production rate of 2.356 kg/s. An economic analysis of the plant was also performed using the H2A Analysis Methodology developed by the Department of Energy (DOE) Hydrogen Program. The results of the economic analysis demonstrated that the HTE hydrogen production plant driven by a high-temperature helium-cooled nuclear power plant can deliver hydrogen at a competitive cost using realistic financial and cost estimating assumptions. A required cost of $3.23 per kg of hydrogen produced was calculated assuming an internal rate of return of 10%. Approximately 73% of this cost ($2.36/kg) is the result of capital costs associated

  4. Commercial scale gasification test with Kentucky coal

    SciTech Connect

    Roeger, A.; Jones, J.E.

    1984-03-01

    The paper describes in some detail the coal testing programme carried out by Tri-State Synfuels. One of the major elements in the programme was a commercial-scale gasification test with Kentucky 9 coal in a Lurgi dry-bottom gasifier. This was carried out at the Sasol One plant in Sasolburg, S. Africa, in 1981. Other parts of the programme included coal selection, characterisation, stockpile weatherability, corrosion testing, by-product characterisation and waste water treatability.

  5. Inherently safe nuclear-driven internal combustion engines

    SciTech Connect

    Alesso, P.; Chow, Tze-Show; Condit, R.; Heidrich, J.; Pettibone, J.; Streit, R.

    1991-06-14

    A family of nuclear driven engines is described in which nuclear energy released by fissioning of uranium or plutonium in a prompt critical assembly is used to heat a working gas. Engine performance is modeled using a code that calculates hydrodynamics, fission energy production, and neutron transport self-consistently. Results are given demonstrating a large negative temperature coefficient that produces self-shutoff of energy production. Reduced fission product inventory and the self-shutoff provide inherent nuclear safety. It is expected that nuclear engine reactor units could be scaled from 100 MW on up. 7 refs., 3 figs.

  6. Nuclear driven water decomposition plant for hydrogen production

    NASA Technical Reports Server (NTRS)

    Parker, G. H.; Brecher, L. E.; Farbman, G. H.

    1976-01-01

    The conceptual design of a hydrogen production plant using a very-high-temperature nuclear reactor (VHTR) to energize a hybrid electrolytic-thermochemical system for water decomposition has been prepared. A graphite-moderated helium-cooled VHTR is used to produce 1850 F gas for electric power generation and 1600 F process heat for the water-decomposition process which uses sulfur compounds and promises performance superior to normal water electrolysis or other published thermochemical processes. The combined cycle operates at an overall thermal efficiency in excess of 45%, and the overall economics of hydrogen production by this plant have been evaluated predicated on a consistent set of economic ground rules. The conceptual design and evaluation efforts have indicated that development of this type of nuclear-driven water-decomposition plant will permit large-scale economic generation of hydrogen in the 1990s.

  7. COMMERCIAL-SCALE AEROBIC-ANAEROBIC BIOREACTOR LANDFILL OPERATIONS

    EPA Science Inventory

    A sequential aerobic-anaerobic treatment system has been applied at a commercial scale (3,000 ton per day) municipal solid waste landfill in Kentucky, USA since 2001. In this system, the uppermost layer of landfilled waste is aerated and liquid waste including leachate, surface w...

  8. Environmental assessment of the BX in-situ oil shale project and potential commercial scale development. Final report

    SciTech Connect

    Gardiner, T.J.; Donovan, M.; Hafele, R.

    1985-01-01

    This report presents a summary of the observed effects of the pilot scale BX in-situ oil shale project on the local environment. It also provides an estimate of potential impacts on the environment from a conceptual 10,000 bbl/day commercial scale operation. The BX process uses superheated steam as a heat carrying medium for the in-situ retorting of oil shale in the Green River Formation leached zone. No air quality monitoring was required or conducted. There were no serious impacts to surface or ground water from the research facility. Minimal effects on the fauna and flora were observed. Those occurring resulted from alterations to the stream channel which disturbed the substrate. It is projected that the commercial scale concept may result in significant impacts on air resources as a result of fugitive dusts and hydrocarbons. The potential impacts to water resources resulting from construction and operation of commercial scale facility include increased runoff, sediment loading and water quality degradation to both surface and ground water. However, the present concept of the commercial scale facility would minimize most of the aforementioned impacts. The normal operations of a commercial scale facility pose no harmful impacts to the fauna and flora of Black Sulphur Creek. Impacts could occur, however, from accidental spills or leaks from pipelines or from stream disturbances during construction activities. 49 references, 30 figures, 36 tables. (DMC)

  9. Commercial scale irradiation for insect disinfestation preserves peach quality

    NASA Astrophysics Data System (ADS)

    McDonald, Heather; McCulloch, Mary; Caporaso, Fred; Winborne, Ian; Oubichon, Michon; Rakovski, Cyril; Prakash, Anuradha

    2012-06-01

    Irradiation is approved as a generic quarantine treatment by the US Department of Agriculture, Animal and Plant Health Inspection Service. Due to the effectiveness of irradiation in controlling insects on commodities, there is a growing need to understand the effects of low dose irradiation on fruit quality. The goal of this study was to determine the sensitivity of peaches (Prunus persica) to irradiation, and secondly, to determine the effect of commercial scale treatment on shelf-life, overall quality and consumer liking. Six varieties of peaches were irradiated in small batches at 0.29, 0.49, 0.69 and 0.90 kGy to observe the sensitivity of peaches at different dose levels. Changes in quality were evaluated by 8 trained panelists using descriptive analysis. Sensory characteristics (color, smoothness, aroma, touch firmness, mouth firmness, graininess, overall flavor and off-flavor) were evaluated at 2-4 day intervals and untreated samples served as control. To simulate commercial treatment, peaches were irradiated in pallet quantities at a target dose level of 0.4 kGy. The average absorbed dose was 0.66 kGy with an average dose uniformity ratio of 1.57. Commercially treated peaches were evaluated by 40-80 untrained consumers for acceptability routinely throughout the shelf life. Titratable acidity, Brix, texture and weight loss were also monitored for both commercial and small scale irradiated peaches. There was no dose effect on TA, Brix and weight loss due to irradiation. Peaches irradiated at 0.69 and 0.90 kGy were darker in flesh color, more juicy and less firm as determined by the trained panel and analytical pressure tests. Commercial scale irradiation did not adversely affect shelf life but was seen to enhance ripening. This, however, was perceived as a positive change by consumers. Overall, consumers rated the acceptability of irradiated peaches higher than untreated peaches. Statistical analysis was performed using linear mixed models to find determinates

  10. Guide to commercial-scale ethanol production and financing

    SciTech Connect

    1980-11-01

    This document is designed to lead the potential investor through all the steps necessary to develop a business plan and prepare a feasibility analysis for a site-specific project. Emphasis is placed on marketing, financing, management, and incentives rather than primarily technical matters. The introduction provides an overview of the perspectives and issues in the alcohol fuels industry. Chapter II seeks to surface factors which affect the decisionmaking process. The chapter attempts to lead the investor step-by-step through the series of decisions and choices to be made before reaching the final decision to enter the business. Chapter III describes the types of feedstocks available and relates them to areas within the United States. Trends and fluctuations in the price of the major grain feedstocks are also discussed in terms of their potential use and value compared to other feeds. Chapter IV discusses the market potential of ethanol and its coproducts, and examines how the location of the ethanol markets in relation to those of the feedstock supplies may influence selection of a plant site. Various aspects of plant design are discussed. A 50 million gallon per year plant is analyzed to provide the general technical background and costing data required in analyzing plants of various sizes and designs. Safety aspects and environmental concerns are treated in Chapters VI and VII. The regulations are reviewed and their impact on plant design and operation is discussed. The basic elements of a business plan are described which lead to an approach for development of the feasibility study. Other information on financial assistance, regulations, current legislation, and reference material is given in the Appendices.

  11. System Evaluation and Life-Cycle Cost Analysis of a Commercial-Scale High-Temperature Electrolysis Hydrogen Production Plant

    SciTech Connect

    Edwin A. Harvego; James E. O'Brien; Michael G. McKellar

    2012-11-01

    Results of a system evaluation and lifecycle cost analysis are presented for a commercial-scale high-temperature electrolysis (HTE) central hydrogen production plant. The plant design relies on grid electricity to power the electrolysis process and system components, and industrial natural gas to provide process heat. The HYSYS process analysis software was used to evaluate the reference central plant design capable of producing 50,000 kg/day of hydrogen. The HYSYS software performs mass and energy balances across all components to allow optimization of the design using a detailed process flow sheet and realistic operating conditions specified by the analyst. The lifecycle cost analysis was performed using the H2A analysis methodology developed by the Department of Energy (DOE) Hydrogen Program. This methodology utilizes Microsoft Excel spreadsheet analysis tools that require detailed plant performance information (obtained from HYSYS), along with financial and cost information to calculate lifecycle costs. The results of the lifecycle analyses indicate that for a 10% internal rate of return, a large central commercial-scale hydrogen production plant can produce 50,000 kg/day of hydrogen at an average cost of $2.68/kg. When the cost of carbon sequestration is taken into account, the average cost of hydrogen production increases by $0.40/kg to $3.08/kg.

  12. Determination of the nuclear-induced electrical conductivity in a nuclear-driven MHD device

    SciTech Connect

    Bitteker, L.

    1994-06-01

    The continual need for more efficient energy conversion techniques for space, sea, and terrestrial systems has renewed interest in nuclear-driven magnetohydrodynamic (MHD) energy conversion. The concept of nuclear-driven MHD energy conversion utilizes a flow seeded with a neutron absorbing species. The energy released in neutron absorption or fission processes is used to ionize the flow and enhance electrical conductivity. Research into the use of {sup 3}He/{sup 4}He mixtures in the 1960`s and 1970`s suggested the enhancement is insufficient for MHD purposes. However, new calculations suggest a region of conditions not previously considered may provide significant conductivity enhancement. Specifically, at densities less than standard atmospheric density and neutron flux greater than 1{times}10{sup 12}/cm{sup 2}s, conductivity greater than 10 mho/m may be achievable. These calculations also suggest conductivity`s of several hundred mho/m may be possible for an achievable range of conditions. Additionally, the nuclear-induced conductivity is strongly density dependent and weakly temperature dependent. Therefore, higher flow velocities, and hence higher power densities than those used in traditional MHD channels utilizing thermal ionization are possible. In order to confirm these promising calculations, a series of experiments has been proposed.

  13. Commercial-Scale Demonstration of the Liquid Phase methanol (LPMEOH) Process A DOE Assessment

    SciTech Connect

    National Energy Technology Laboratory

    2003-10-27

    The U.S. Department of Energy (DOE) Clean Coal Technology (CCT) Program seeks to offer the energy marketplace more efficient and environmentally benign coal utilization technology options by demonstrating them in industrial settings. This document is a DOE post-project assessment (PPA) of one of the projects selected in Round III of the CCT Program, the commercial-scale demonstration of the Liquid Phase Methanol (LPMEOH{trademark}) Process, initially described in a Report to Congress by DOE in 1992. Methanol is an important, large-volume chemical with many uses. The desire to demonstrate a new process for the production of methanol from coal, prompted Air Products and Chemicals, Inc. (Air Products) to submit a proposal to DOE. In October 1992, DOE awarded a cooperative agreement to Air Products to conduct this project. In March 1995, this cooperative agreement was transferred to Air Products Liquid Phase Conversion Company, L.P. (the Partnership), a partnership between Air Products and Eastman Chemical Company (Eastman). DOE provided 43 percent of the total project funding of $213.7 million. Operation of the LPMEOH Demonstration Unit, which is sited at Eastman's chemicals-from-coal complex in Kingsport, Tennessee, commenced in April 1997. Although operation of the CCT project was completed in December 2002, Eastman continues to operate the LPMEOH Demonstration Unit for the production of methanol. The independent evaluation contained herein is based primarily on information from Volume 2 of the project's Final Report (Air Products Liquid Phase Conversion Co., L.P. 2003), as well as other references cited.

  14. Battery Energy Storage Market: Commercial Scale, Lithium-ion Projects in the U.S.

    SciTech Connect

    McLaren, Joyce; Gagnon, Pieter; Anderson, Kate; Elgqvist, Emma; Fu, Ran; Remo, Tim

    2016-10-01

    This slide deck presents current market data on the commercial scale li-ion battery storage projects in the U.S. It includes existing project locations, cost data and project cost breakdown, a map of demand charges across the U.S. and information about how the ITC and MACRS apply to energy storage projects that are paired with solar PV technology.

  15. A commercial-scale in-pond raceway system for ictalurid catfish production

    Technology Transfer Automated Retrieval System (TEKTRAN)

    A commercial-scale, in-pond raceway system was constructed in 2007 on a commercial catfish fish farm in west Alabama. The in-pond raceway system was installed in a 2.43-ha earthen pond with an average depth of 1.67 m. A slow-rotating paddlewheel (1.17 revolutions per minute) installed in each rac...

  16. On-site evaluation of commercial-scale hybrid catfish production using cryopreserved blue catfish sperm

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Cryopreservation is an effective tool for conservation of genetic resources and is becoming increasingly used worldwide with aquatic species. Broadening the application of this technology to a commercial scale through high-throughput approaches has become essential for use with aquatic species. This...

  17. State Enabling Legislation for Commercial-Scale Wind Power Siting and the Local Government Role

    SciTech Connect

    McElfish, J.M.; Gersen, S.

    2011-05-31

    Siting of commercial-scale wind facilities (>5MW) is determined primarily by state laws. State laws either leave siting regulation to local governments, prescribe and constrain the role for local governments, establish state standards, or preempt local governance by having state institutions govern siting. Siting regulation is extremely important to the advancement of wind generation in the United States. Major siting decisions lie ahead for state and local governments as the nation diversifies its energy portfolio. An increase in the number of new wind facilities, siting in more locations and in more heavily populated areas, will require attention to the laws and regulations that govern siting. Local governments exercise some authority over commercial-scale wind facility siting in 48 of the 50 states. In 34 states, local governments have substantial autonomy to regulate the siting of most or all commercial-scale wind facilities. A few states authorize local governments to regulate wind facility siting, but make the scope of local regulation subject to limitations defined by state law. Eleven states set size thresholds for state regulatory involvement with local governments in these states regulating smaller facilities and state boards regulating larger ones (either exclusively or concurrently with local governments). In just under a third of the states, siting of most or all commercial-scale wind facilities requires approval by both state and local government bodies. Only a few states reserve the regulation of siting of all or virtually all commercial-scale wind facilities to state boards and commissions. The content of the applicable regulations is more important, in general, than the level of government responsible for the decision. Several states that assign siting responsibilities to local governments have specified some of the content and the limits of local regulation. About 1/5 of the states have directed boards and commissions to develop statewide

  18. Commercial-scale process design for thin-film solar cells

    NASA Astrophysics Data System (ADS)

    Russell, T. W. F.; Baron, B. N.; Rocheleau, R. E.

    Process and manufacturing costs for commercial-scale production of thin-film solar cells are examined from the viewpoint of the chemical process industry, with emphasis on CdS/Cu2S cells. The cells comprise opaque contact, collector/converter, absorber/generator, transparent contact, and encapsulation/antireflective coating layers. Each layer is deposited as a separate unit operation, through either continuous or batch processing methods. The scale-up of laboratory-verified cell manufacturing steps to commercial processing is detailed from the choice of a Zn-plated copper foil substrate to the bonding of a 1/16 in. tempered glass protective layer with polyvinyl butyral. The total product cost is calculated as a sum of raw materials, utilities, labor, and capital investment costs, using a cost/W for a 1 GW plant. Continuous processing results in a $0.50/W cell with raw materials accounting for 38% of the total product cost.

  19. Commercial Scale Cucumber Fermentations Brined with Calcium Chloride Instead of Sodium Chloride.

    PubMed

    Pérez-Díaz, I M; McFeeters, R F; Moeller, L; Johanningsmeier, S D; Hayes, J; Fornea, D S; Rosenberg, L; Gilbert, C; Custis, N; Beene, K; Bass, D

    2015-12-01

    Development of low salt cucumber fermentation processes present opportunities to reduce the amount of sodium chloride (NaCl) that reaches fresh water streams from industrial activities. The objective of this research was to translate cucumber fermentation brined with calcium chloride (CaCl2 ) instead of NaCl to commercial scale production. Although CaCl2 brined cucumber fermentations were stable in laboratory experiments, commercial scale trials using 6440 L open-top tanks rapidly underwent secondary cucumber fermentation. It was understood that a limited air purging routine, use of a starter culture and addition of preservatives to the cover brine aids in achieving the desired complete cucumber fermentation. The modified process was used for subsequent commercial trials using 12490 and 28400 L open-top tanks packed with variable size cucumbers and from multiple lots, and cover brines containing CaCl2 and potassium sorbate to equilibrated concentrations of 100 and 6 mM, respectively. Lactobacillus plantarum LA0045 was inoculated to 10(6) CFU/mL, and air purging was applied for two 2-3 h periods per day for the first 10 d of fermentation and one 2-3 h period per day between days 11 and 14. All fermentations were completed, as evidenced by the full conversion of sugars to lactic acid, decrease in pH to 3.0, and presented microbiological stability for a minimum of 21 d. This CaCl2 process may be used to produce fermented cucumbers intended to be stored short term in a manner that reduces pollution and waste removal costs.

  20. Commercial scale validation of a process scale-up model for lubricant blending of pharmaceutical powders.

    PubMed

    Kushner, Joseph; Schlack, Holger

    2014-11-20

    An experimental study was conducted to verify that lubrication mixing in commercial-scale bin blenders can be described by a previously-reported lubrication blending process scale-up model. Specifically, the mixing of two placebo formulations (2:1 MCC:lactose, and 2:1 MCC:DCP) with 1% magnesium stearate in 100, 400, and 2000 L bin blenders at 30% and 70% blend fill levels for several extents of lubricant mixing was examined. The lubricated powder blends were assessed for bulk/tapped density and powder flow, as measured by Hausner's ratio. The blends were then compressed into tablets and evaluated for tensile strength, friability, and disintegration. It was observed that the lubrication rate constant, γ, for tablet tensile strength and for bulk specific volume were similar. Furthermore, powder flow, as measured by Hausner's ratio, improved with increased extent of lubrication. Tablet disintegration and tablet friability were both minimally affected as a result of extended lubrication for the placebos blends evaluated in this study. The results of this study confirm that the lubrication mixing model can be applied to scale-up the lubrication blending process from batches made in 30 mL bottle blenders to batches made in 2000 L bin blenders, which is a range of nearly five orders of magnitude.

  1. Development and testing of a commercial-scale coal-fired combustion system, Phase 3

    SciTech Connect

    Litka, A.F.; Breault, R.W.

    1991-10-01

    Within the commercial sector, oil and natural gas are the predominant fuels used to meet the space-heating needs of schools, office buildings, apartment complexes, and other similar structures. In general, these buildings require firing rates of 1 to 10 million Btu/hr. The objective of this program is to demonstrate the technical and economic viability of a coal-fired combustion system for this sector. The commercial-scale coal-water slurry (CWS)-fired space heating system will be a scale-up of a CWS-fired residential warm-air heating system developed by Tecogen under contract to the Department of Energy, Pittsburgh Energy Technology Center. This system included a patented nonslagging combustor known as IRIS, for Inertial Reactor with Internal Separation. This combustion technology, which has demonstrated high combustion efficiency using CWS fuels at input rates of 100,000 Btu/hr, will be scaled to operate at 2 to 5 millon Btu/hr. Along with the necessary fuel storage and delivery, heat recovery, and control equipment, the system will include pollution control devices to meet targeted values of NO{sub x}, S0{sub 2}, and particulate emissions. In general, the system will be designed to match the reliability, safety, turndown, and ignition performance of gas or oil-fired systems.

  2. Development and testing of a commercial-scale coal-fired combustion system, Phase 3

    SciTech Connect

    Litka, A.F.; Breault, R.W.

    1991-07-01

    Within the commercial sector, oil and natural gas are the predominant fuels used to meet the space-heating needs of schools, office buildings, apartment complexes, and other similar structures. In general, these buildings require firing rates of 1 to 10 million Btu/hr. The objective of this program is to demonstrate the technical and economic viability of a coal-fired combustion system for this sector. The commercial-scale coal-water slurry (CWS)-fired space heating system will be a scale-up of a CWS-fired residential warm-air heating system developed by Tecogen under contract to the Department of Energy, Pittsburgh Energy Technology Center. This system included a patented nonslagging combustor known as IRIS, for Inertial Reactor with Internal Separation. This combustion technology, which has demonstrated high combustion efficiency using CWS fuels at input rates of 100,000 Btu/hr, will be scaled to operate at 2 to 5 millon Btu/hr. Along with the necessary fuel storage and delivery, heat recovery, and control equipment, the system will include pollution control devices to meet targeted values of NO{sub x}, S0{sub 2}, and particulate emissions. In general, the system will be designed to match the reliability, safety, turndown, and ignition performance of gas or oil-fired systems.

  3. Enhanced ethanol production at commercial scale from molasses using high gravity technology by mutant S. cerevisiae.

    PubMed

    Arshad, Muhammad; Hussain, Tariq; Iqbal, Munawar; Abbas, Mazhar

    2017-02-16

    Very high gravity (VHG) technology was employed on industrial scale to produce ethanol from molasses (fermented) as well as by-products formation estimation. The effect of different Brix° (32, 36 and 40) air-flow rates (0.00, 0.20, 0.40, and 0.60vvm) was studied on ethanol production. The maximum ethanol production was recorded to be 12.2% (v/v) at 40 Brix° with 0.2vvm air-flow rate. At optimum level aeration and 40 Brix° VHG, the residual sugar level was recorded in the range of 12.5-18.5g/L, whereas the viable cell count remained constant up to 50h of fermentation and dry matter production increased with fermentation time. Both water and steam consumption reduced significantly under optimum conditions of Brix° and aeration rate with compromising the ethanol production. Results revealed VHG with continuous air flow is viable technique to reduce the ethanol production cost form molasses at commercial scale.

  4. Mountaineer Commercial Scale Carbon Capture and Storage Project Topical Report: Preliminary Public Design Report

    SciTech Connect

    Guy Cerimele

    2011-09-30

    This Preliminary Public Design Report consolidates for public use nonproprietary design information on the Mountaineer Commercial Scale Carbon Capture & Storage project. The report is based on the preliminary design information developed during the Phase I - Project Definition Phase, spanning the time period of February 1, 2010 through September 30, 2011. The report includes descriptions and/or discussions for: (1) DOE's Clean Coal Power Initiative, overall project & Phase I objectives, and the historical evolution of DOE and American Electric Power (AEP) sponsored projects leading to the current project; (2) Alstom's Chilled Ammonia Process (CAP) carbon capture retrofit technology and the carbon storage and monitoring system; (3) AEP's retrofit approach in terms of plant operational and integration philosophy; (4) The process island equipment and balance of plant systems for the CAP technology; (5) The carbon storage system, addressing injection wells, monitoring wells, system monitoring and controls logic philosophy; (6) Overall project estimate that includes the overnight cost estimate, cost escalation for future year expenditures, and major project risks that factored into the development of the risk based contingency; and (7) AEP's decision to suspend further work on the project at the end of Phase I, notwithstanding its assessment that the Alstom CAP technology is ready for commercial demonstration at the intended scale.

  5. Commercial-Scale Demonstration of the Liquid Phase Methanol (LPMEOH(TM)) Process

    SciTech Connect

    1997-09-30

    The Liquid Phase Methanol (LPMEOH) Demonstration Project at Kingsport, Tennessee, is a $213.7 million cooperative agreement between the U.S. Department of Energy (DOE) and Air Products Liquid Phase Conversion Company, L.P. (the Partnership). Ak Products and Chemicals, Inc. (Air Products) and Eastman Chemical Company (Eastman) formed the Partnership to execute the Demonstration Project. The LPMEOITM Process Demonstration Unit was built at a site located at the Eastman complex in Kingsport. During this reporting period, DOE accepted the recommendation to continue with dimethyl ether (DME) design verification testing (DVT). DME design verification testing studies show the liquid phase DME (LPDME) process will have a significant economic advantage for the coproduction of DME for local markets. An LPDME catalyst system with reasonable long-term activity and stzibility is being developed. Planning for a proof-of-concept test run at the LaPorte Alternative Fuels Development Unit (AFDU) was recommended. DOE issued a letter dated 31 July 1997 accepting the recommendation to continue design verification testing. In order to allow for scale-up of the manufacturing technique for the dehydration catalyst from the pilot plant to the commercial scale, the time required to produce the catalyst to the AFDU has slipped. The new estimated delivery date is 01 June 1998.

  6. Commercial-scale biotherapeutics manufacturing facility for plant-made pharmaceuticals.

    PubMed

    Holtz, Barry R; Berquist, Brian R; Bennett, Lindsay D; Kommineni, Vally J M; Munigunti, Ranjith K; White, Earl L; Wilkerson, Don C; Wong, Kah-Yat I; Ly, Lan H; Marcel, Sylvain

    2015-10-01

    Rapid, large-scale manufacture of medical countermeasures can be uniquely met by the plant-made-pharmaceutical platform technology. As a participant in the Defense Advanced Research Projects Agency (DARPA) Blue Angel project, the Caliber Biotherapeutics facility was designed, constructed, commissioned and released a therapeutic target (H1N1 influenza subunit vaccine) in <18 months from groundbreaking. As of 2015, this facility was one of the world's largest plant-based manufacturing facilities, with the capacity to process over 3500 kg of plant biomass per week in an automated multilevel growing environment using proprietary LED lighting. The facility can commission additional plant grow rooms that are already built to double this capacity. In addition to the commercial-scale manufacturing facility, a pilot production facility was designed based on the large-scale manufacturing specifications as a way to integrate product development and technology transfer. The primary research, development and manufacturing system employs vacuum-infiltrated Nicotiana benthamiana plants grown in a fully contained, hydroponic system for transient expression of recombinant proteins. This expression platform has been linked to a downstream process system, analytical characterization, and assessment of biological activity. This integrated approach has demonstrated rapid, high-quality production of therapeutic monoclonal antibody targets, including a panel of rituximab biosimilar/biobetter molecules and antiviral antibodies against influenza and dengue fever.

  7. The key to commercial-scale geological CO2 sequestration: Displaced fluid management

    USGS Publications Warehouse

    Surdam, R.C.; Jiao, Z.; Stauffer, P.; Miller, T.

    2011-01-01

    The Wyoming State Geological Survey has completed a thorough inventory and prioritization of all Wyoming stratigraphic units and geologic sites capable of sequestering commercial quantities of CO2 (5-15 Mt CO 2/year). This multi-year study identified the Paleozoic Tensleep/Weber Sandstone and Madison Limestone (and stratigraphic equivalent units) as the leading clastic and carbonate reservoir candidates for commercial-scale geological CO2 sequestration in Wyoming. This conclusion was based on unit thickness, overlying low permeability lithofacies, reservoir storage and continuity properties, regional distribution patterns, formation fluid chemistry characteristics, and preliminary fluid-flow modeling. This study also identified the Rock Springs Uplift in southwestern Wyoming as the most promising geological CO2 sequestration site in Wyoming and probably in any Rocky Mountain basin. The results of the WSGS CO2 geological sequestration inventory led the agency and colleagues at the UW School of Energy Resources Carbon Management Institute (CMI) to collect available geologic, petrophysical, geochemical, and geophysical data on the Rock Springs Uplift, and to build a regional 3-D geologic framework model of the Uplift. From the results of these tasks and using the FutureGen protocol, the WSGS showed that on the Rock Springs Uplift, the Weber Sandstone has sufficient pore space to sequester 18 billion tons (Gt) of CO2, and the Madison Limestone has sufficient pore space to sequester 8 Gt of CO2. ?? 2011 Published by Elsevier Ltd.

  8. Controls and rates of acid production in commercial-scale sulfur blocks.

    PubMed

    Birkham, T K; Hendry, M J; Barbour, S L; Lawrence, J R

    2010-01-01

    Acidic drainage (pH 0.4-1.0) from oxidizing elemental sulfur (S(0)) blocks is an environmental concern in regions where S(0) is stockpiled. In this study, the locations, controls, and rates of H(2)SO(4) production in commercial-scale S(0) blocks ( approximately 1-2 x 10(6) m(3)) in northern Alberta, Canada, were estimated. In situ modeling of O(2) concentrations ([O(2)]) suggest that 70 to >97% of the annual H(2)SO(4) production occurs in the upper 1 m of the blocks where temperatures increase to >15 degrees C during the summer. Laboratory experiments show that S(0) oxidation rates are sensitive to temperature (Q(10) = 4.3) and dependent on the activity of autotrophic S(0)-oxidizing microbes. The annual efflux of SO(4) in drainage water from a S(0) block (5.5 x 10(5) kg) was within the estimated range of SO(4) production within the block (2.7 x 10(5) to 1.2 x 10(6) kg), suggesting that H(2)SO(4) production and removal rates were approximately equal during the study period. The low mean relative humidity within the block (68%; SD = 17%; n = 21) was attributed to osmotic suction from elevated H(2)SO(4) concentrations and suggests a mean in situ pH of approximately -2.1. The low pH of drainage waters was attributed to the mixing of fresh infiltrating water and low-pH in situ water. Heat generation during S(0) oxidation was an important factor in maintaining elevated temperatures (mean, 11.1 degrees C) within the block. The implications of this research are relevant globally because construction methods and the physical properties of S(0) blocks are similar worldwide.

  9. A Novel Treatment Protects Chlorella at Commercial Scale from the Predatory Bacterium Vampirovibrio chlorellavorus

    PubMed Central

    Ganuza, Eneko; Sellers, Charles E.; Bennett, Braden W.; Lyons, Eric M.; Carney, Laura T.

    2016-01-01

    The predatory bacterium, Vampirovibrio chlorellavorus, can destroy a Chlorella culture in just a few days, rendering an otherwise robust algal crop into a discolored suspension of empty cell walls. Chlorella is used as a benchmark for open pond cultivation due to its fast growth. In nature, V. chlorellavorus plays an ecological role by controlling this widespread terrestrial and freshwater microalga, but it can have a devastating effect when it attacks large commercial ponds. We discovered that V. chlorellavorus was associated with the collapse of four pilot commercial-scale (130,000 L volume) open-pond reactors. Routine microscopy revealed the distinctive pattern of V. chlorellavorus attachment to the algal cells, followed by algal cell clumping, culture discoloration and ultimately, growth decline. The “crash” of the algal culture coincided with increasing proportions of 16s rRNA sequencing reads assigned to V. chlorellavorus. We designed a qPCR assay to predict an impending culture crash and developed a novel treatment to control the bacterium. We found that (1) Chlorella growth was not affected by a 15 min exposure to pH 3.5 in the presence of 0.5 g/L acetate, when titrated with hydrochloric acid and (2) this treatment had a bactericidal effect on the culture (2-log decrease in aerobic counts). Therefore, when qPCR results indicated a rise in V. chlorellavorus amplicons, we found that the pH-shock treatment prevented the culture crash and doubled the productive longevity of the culture. Furthermore, the treatment could be repeatedly applied to the same culture, at the beginning of at least two sequential batch cycles. In this case, the treatment was applied preventively, further increasing the longevity of the open pond culture. In summary, the treatment reversed the infection of V. chlorellavorus as confirmed by observations of bacterial attachment to Chlorella cells and by detection of V. chlorellavorus by 16s rRNA sequencing and qPCR assay. The p

  10. Simulation of commercial scale CO2 injection into a fracture reservoir

    NASA Astrophysics Data System (ADS)

    Li, Y.; Li, S.; Zhang, Y.

    2011-12-01

    Geologic Carbon Sequestration is a proposed means to reduce atmospheric concentration of carbon dioxide (CO2). At Teapot Dome, Wyoming, CO2 will be injected into the Tensleep Formation, a depleted oil reservoir characterized with significant heterogeneity including facies, faults, and fractures. We've collected geological and engineering characterization data of the entire Teapot Dome field, including core data, well logs, seismic data, and production records. All data were screened for accuracy, before subsets of the data are used to build a geologic reservoir model. A formation structural model is created first by interpreting faults and stratigraphy from 3D seismic data. Formation MicroImager logs are analyzed for fracture characteristics to generate in-situ fracture intensity at wells, which is subsequently interpolated throughout the model with kriging. Based on the intensity and a set of geometric fracture parameters (constrained by outcrop and core measurements), a 3D stochastic Discrete Fracture Network (DFN) is created. One realization of the DFN is upscaled to a dual-porosity simulation model using a variant of the Oda's method. This method upscales the fracture network to an effective grid-block fracture permeability. To account for fluid transfer from matrix to fracture, a sigma factor is computed using average fracture spacings within the grid block. Matrix porosity is populated in the model by kriging interpolation of well-log-derived values. With the dual-porosity model, CO2 is injected near the crest of the dome (the proposed location) at a rate of 2.6 Mt/year for 50 years, with an injection bottomhole pressure set at 160% hydrostatic pressure. Boundary of the model is open except along one bounding fault assumed sealed. Results of the simulation suggest that provided that fluid pressure buildup is not an issue (simulated pressure buildup near the fault is minor), the Tensleep Formation at Teapot Dome can sustain commercial-scale injection over time

  11. COMMERCIAL-SCALE DEMONSTRATION OF THE LIQUID PHASE METHANOL (LPMEOH) PROCESS

    SciTech Connect

    E.C. Heydorn; B.W. Diamond; R.D. Lilly

    2003-06-01

    This project, which was sponsored by the U.S. Department of Energy (DOE) under the Clean Coal Technology Program to demonstrate the production of methanol from coal-derived synthesis gas (syngas), has completed the 69-month operating phase of the program. The purpose of this Final Report for the ''Commercial-Scale Demonstration of the Liquid Phase Methanol (LPMEOH{trademark}) Process'' is to provide the public with details on the performance and economics of the technology. The LPMEOH{trademark} Demonstration Project was a $213.7 million cooperative agreement between the DOE and Air Products Liquid Phase Conversion Company, L.P. (the Partnership). The DOE's cost share was $92,708,370 with the remaining funds coming from the Partnership. The LPMEOH{trademark} demonstration unit is located at the Eastman Chemical Company (Eastman) chemicals-from-coal complex in Kingsport, Tennessee. The technology was the product of a cooperative development effort by Air Products and Chemicals, Inc. (Air Products) and DOE in a program that started in 1981. Developed to enhance electric power generation using integrated gasification combined cycle (IGCC) technology, the LPMEOH{trademark} Process is ideally suited for directly processing gases produced by modern coal gasifiers. Originally tested at the Alternative Fuels Development Unit (AFDU), a small, DOE-owned process development facility in LaPorte, Texas, the technology provides several improvements essential for the economic coproduction of methanol and electricity directly from gasified coal. This liquid phase process suspends fine catalyst particles in an inert liquid, forming a slurry. The slurry dissipates the heat of the chemical reaction away from the catalyst surface, protecting the catalyst, and allowing the methanol synthesis reaction to proceed at higher rates. The LPMEOH{trademark} Demonstration Project accomplished the objectives set out in the Cooperative Agreement with DOE for this Clean Coal Technology project

  12. Towards commercial scale postcombustion capture of CO2 with monoethanolamine solvent: key considerations for solvent management and environmental impacts.

    PubMed

    Reynolds, Alicia J; Verheyen, T Vincent; Adeloju, Samuel B; Meuleman, Erik; Feron, Paul

    2012-04-03

    Chemical absorption with aqueous amine solvents is the most advanced technology for postcombustion capture (PCC) of CO(2) from coal-fired power stations and a number of pilot scale programs are evaluating novel solvents, optimizing energy efficiency, and validating engineering models. This review demonstrates that the development of commercial scale PCC also requires effective solvent management guidelines to ensure minimization of potential technical and environmental risks. Furthermore, the review reveals that while solvent degradation has been identified as a key source of solvent consumption in laboratory scale studies, it has not been validated at pilot scale. Yet this is crucial as solvent degradation products, such as organic acids, can increase corrosivity and reduce the CO(2) absorption capacity of the solvent. It also highlights the need for the development of corrosion and solvent reclamation technologies, as well as strategies to minimize emissions of solvent and degradation products, such as ammonia, aldehydes, nitrosamines and nitramines, to the atmosphere from commercial scale PCC. Inevitably, responsible management of aqueous and solid waste will require more serious consideration. This will ultimately require effective waste management practices validated at pilot scale to minimize the likelihood of adverse human and environmental impacts from commercial scale PCC.

  13. Jumpstarting commercial-scale CO2 capture and storage with ethylene production and enhanced oil recovery in the US Gulf

    DOE PAGES

    Middleton, Richard S.; Levine, Jonathan S.; Bielicki, Jeffrey M.; ...

    2015-04-27

    CO2 capture, utilization, and storage (CCUS) technology has yet to be widely deployed at a commercial scale despite multiple high-profile demonstration projects. We suggest that developing a large-scale, visible, and financially viable CCUS network could potentially overcome many barriers to deployment and jumpstart commercial-scale CCUS. To date, substantial effort has focused on technology development to reduce the costs of CO2 capture from coal-fired power plants. Here, we propose that near-term investment could focus on implementing CO2 capture on facilities that produce high-value chemicals/products. These facilities can absorb the expected impact of the marginal increase in the cost of production onmore » the price of their product, due to the addition of CO2 capture, more than coal-fired power plants. A financially viable demonstration of a large-scale CCUS network requires offsetting the costs of CO2 capture by using the CO2 as an input to the production of market-viable products. As a result, we demonstrate this alternative development path with the example of an integrated CCUS system where CO2 is captured from ethylene producers and used for enhanced oil recovery in the U.S. Gulf Coast region.« less

  14. System Analyses of High and Low-Temperature Interface Designs for a Nuclear-Driven High-Temperature Electrolysis Hydrogen Production Plant

    SciTech Connect

    E. A. Harvego; J. E. O'Brien

    2009-07-01

    As part of the Next Generation Nuclear Plant (NGNP) project, an evaluation of a low-temperature heat-pump interface design for a nuclear-driven high-temperature electrolysis (HTE) hydrogen production plant was performed using the UniSim process analysis software. The lowtemperature interface design is intended to reduce the interface temperature between the reactor power conversion system and the hydrogen production plant by extracting process heat from the low temperature portion of the power cycle rather than from the high-temperature portion of the cycle as is done with the current Idaho National Laboratory (INL) reference design. The intent of this design change is to mitigate the potential for tritium migration from the reactor core to the hydrogen plant, and reduce the potential for high temperature creep in the interface structures. The UniSim model assumed a 600 MWt Very-High Temperature Reactor (VHTR) operating at a primary system pressure of 7.0 MPa and a reactor outlet temperature of 900°C. The lowtemperature heat-pump loop is a water/steam loop that operates between 2.6 MPa and 5.0 MPa. The HTE hydrogen production loop operated at 5 MPa, with plant conditions optimized to maximize plant performance (i.e., 800°C electrolysis operating temperature, area specific resistance (ASR) = 0.4 ohm-cm2, and a current density of 0.25 amps/cm2). An air sweep gas system was used to remove oxygen from the anode side of the electrolyzer. Heat was also recovered from the hydrogen and oxygen product streams to maximize hydrogen production efficiencies. The results of the UniSim analysis showed that the low-temperature interface design was an effective heat-pump concept, transferring 31.5 MWt from the low-temperature leg of the gas turbine power cycle to the HTE process boiler, while consuming 16.0 MWe of compressor power. However, when this concept was compared with the current INL reference direct Brayton cycle design and with a modification of the reference design to

  15. SEDIMENT DECONTAMINATION TREATMENT TRAIN: COMMERCIAL-SCALE DEMONSTRATION FOR THE PORT OF NEW YORK/NEW JERSEY

    SciTech Connect

    JONES,K.W.; STERN,E.A.; DONATO,K.R.; CLESCERI,N.L.

    1999-07-01

    Decontamination and beneficial use of dredged material is a component of a comprehensive Dredged Material Management Plan for the Port of New York and New Jersey. The authors describe here a regional contaminated sediment decontamination program that is being implemented to meet the needs of the Port. The components of the train include: (1) dredging and preliminary physical processing (materials handling), (2) decontamination treatment, (3) beneficial use, and (4) public outreach. Several types of treatment technologies suitable for use with varying levels of sediment contamination have been selected based on the results of bench- and pilot-scale tests. This work is being conducted under the auspices of the Water Resources Development Act (WRDA). The use of sediment washing is suitable for sediments with low to moderate contamination levels, typical of industrialized waterways. BioGenesis Enterprises and Roy F. Weston, Inc. performed the first phase of an incremental decontamination demonstration with the goal of decontaminating 700 cubic yards (cy) (pilot-scale) for engineering design and cost economics information for commercial scale operations. This pilot test was completed in March, 1999. The next phase will scale-up to operation of a commercial facility capable of treating 40 cy/hr. It is anticipated that this will be completed by January 2000 (250,000 cy/yr). Manufactured topsoil is one beneficial use product from this process. Tests of two high-temperature treatment technologies are also in progress. They are well suited to produce almost complete destruction of organic compounds in moderate to highly contaminated dredged materials and for production of high-value beneficial reuse products. The Institute of Gas Technology is demonstrating a natural gas-fired thermochemical manufacturing process with an initial treatment capacity of 30,000 cy/yr into operation by the fall of 1999. Design and construction of a 100,000 cy/yr facility will be based on the

  16. Commercial-Scale Performance Predictions for High-Temperature Electrolysis Plants Coupled to Three Advanced Reactor Types

    SciTech Connect

    M. G. McKellar; J. E. O'Brien; J. S. Herring

    2007-09-01

    This report presents results of system analyses that have been developed to assess the hydrogen production performance of commercial-scale high-temperature electrolysis (HTE) plants driven by three different advanced reactor – power-cycle combinations: a high-temperature helium cooled reactor coupled to a direct Brayton power cycle, a supercritical CO2-cooled reactor coupled to a direct recompression cycle, and a sodium-cooled fast reactor coupled to a Rankine cycle. The system analyses were performed using UniSim software. The work described in this report represents a refinement of previous analyses in that the process flow diagrams include realistic representations of the three advanced reactors directly coupled to the power cycles and integrated with the high-temperature electrolysis process loops. In addition, this report includes parametric studies in which the performance of each HTE concept is determined over a wide range of operating conditions. Results of the study indicate that overall thermal-to- hydrogen production efficiencies (based on the low heating value of the produced hydrogen) in the 45 - 50% range can be achieved at reasonable production rates with the high-temperature helium cooled reactor concept, 42 - 44% with the supercritical CO2-cooled reactor and about 33 - 34% with the sodium-cooled reactor.

  17. Commercial scale demonstration enhanced oil recovery by micellar-polymer flood. Annual report, October 1979-September 1980

    SciTech Connect

    Howell, J.C.; Snyder, W.O.

    1981-04-01

    This commercial scale test, known as the M-1 Project, is located in Crawford County, Illinois. It encompasses 407 acres of Robinson sand reservoir and covers portions of several waterflood projects that were approaching economic limit. The project includes 248 acres developed on a 2.4-acre five-spot pattern and 159 acres developed on a 5.0-acre five-spot pattern. Development work commenced in late 1974 and has previously been reported. Micellar solution (slug) injection was initiated on February 10, 1977, and is now completed. After 10% of a pore volume of micellar slug was injected, injection of 11% pore volume of Dow 700 Pusher polymer was conducted at a concentration of 1156 ppM. At the end of this reporting period, 625 ppM polymer was being injected into the 2.5-acre pattern and 800 ppM polymer was being injected into the 5.0-acre pattern. The oil cut of the 2.5 and 5.0-acre patterns increased from 8.6% and 5.2%, respectively in September 1979, to 11.0% and 5.9% in September 1980. The oil cut performance has consistently exceeded that predicted for the project. This Fourth Annual Report is organized under the following three Work Breakdown Structures: fluid injection; production; and performance monitoring.

  18. Commercial scale demonstration: enhanced oil recovery by micellar-polymer flood. Annual report, October 1980-September 1981

    SciTech Connect

    Howell, J.C.

    1982-05-01

    This commercial scale test, known as the M-1 Project, is located in Crawford County, Illinois. It encompasses 407 acres of Robinson sand reservoir and covers portions of several waterflood projects that were approaching economic limit. The project includes 248 acres developed on a 2.5-acre five-spot pattern and 159 acres developed on a 5.0-acre five-spot pattern. Development work commenced in late 1974 and has previously been reported. Micellar solution (slug) injection was initiated on February 10, 1977, and is now completed. After 10% of a pore volume of micellar slug was injected, injection of 11% pore volume of Dow 700 Pusher polymer was conducted at a concentration of 1156 ppM. At the end of this reporting period, 625 ppM polymer was being injected into the 2.5-acre pattern and 800 ppM polymer was being injected into the 5.0-acre pattern. The oil cut of the 2.5-acre pattern has decreased from 11.0% in September 1980, to 7.9% in September 1981. The 2.5-acre pattern had been on a plateau since May 1980, and as of May 1981 appears to be on a decline. The oil cut of the 5.0-acre pattern has increased from 5.9% in September 1980, to 10.9% in September 1981. The 5.0-acre pattern experienced a sharp increase in oil cut after 34% of a pore volume of total fluid had been injected and appears to be continuing its incline. This fifth annual report is organized under the following three work breakdown structures: fluid injection; production; and performance monitoring.

  19. Jumpstarting commercial-scale CO2 capture and storage with ethylene production and enhanced oil recovery in the US Gulf

    SciTech Connect

    Middleton, Richard S.; Levine, Jonathan S.; Bielicki, Jeffrey M.; Viswanathan, Hari S.; Carey, J. William; Stauffer, Philip H.

    2015-04-27

    CO2 capture, utilization, and storage (CCUS) technology has yet to be widely deployed at a commercial scale despite multiple high-profile demonstration projects. We suggest that developing a large-scale, visible, and financially viable CCUS network could potentially overcome many barriers to deployment and jumpstart commercial-scale CCUS. To date, substantial effort has focused on technology development to reduce the costs of CO2 capture from coal-fired power plants. Here, we propose that near-term investment could focus on implementing CO2 capture on facilities that produce high-value chemicals/products. These facilities can absorb the expected impact of the marginal increase in the cost of production on the price of their product, due to the addition of CO2 capture, more than coal-fired power plants. A financially viable demonstration of a large-scale CCUS network requires offsetting the costs of CO2 capture by using the CO2 as an input to the production of market-viable products. As a result, we demonstrate this alternative development path with the example of an integrated CCUS system where CO2 is captured from ethylene producers and used for enhanced oil recovery in the U.S. Gulf Coast region.

  20. Development and testing of a commercial-scale coal-fired combustion system, Phase 3. Quarterly technical progress report No. 3, April 1, 1991--June 30, 1991

    SciTech Connect

    Litka, A.F.; Breault, R.W.

    1991-10-01

    Within the commercial sector, oil and natural gas are the predominant fuels used to meet the space-heating needs of schools, office buildings, apartment complexes, and other similar structures. In general, these buildings require firing rates of 1 to 10 million Btu/hr. The objective of this program is to demonstrate the technical and economic viability of a coal-fired combustion system for this sector. The commercial-scale coal-water slurry (CWS)-fired space heating system will be a scale-up of a CWS-fired residential warm-air heating system developed by Tecogen under contract to the Department of Energy, Pittsburgh Energy Technology Center. This system included a patented nonslagging combustor known as IRIS, for Inertial Reactor with Internal Separation. This combustion technology, which has demonstrated high combustion efficiency using CWS fuels at input rates of 100,000 Btu/hr, will be scaled to operate at 2 to 5 millon Btu/hr. Along with the necessary fuel storage and delivery, heat recovery, and control equipment, the system will include pollution control devices to meet targeted values of NO{sub x}, S0{sub 2}, and particulate emissions. In general, the system will be designed to match the reliability, safety, turndown, and ignition performance of gas or oil-fired systems.

  1. Development and testing of a commercial-scale coal-fired combustion system, Phase 3. Quarterly technical progress report No. 2, January 1, 1991--March 31, 1991

    SciTech Connect

    Litka, A.F.; Breault, R.W.

    1991-07-01

    Within the commercial sector, oil and natural gas are the predominant fuels used to meet the space-heating needs of schools, office buildings, apartment complexes, and other similar structures. In general, these buildings require firing rates of 1 to 10 million Btu/hr. The objective of this program is to demonstrate the technical and economic viability of a coal-fired combustion system for this sector. The commercial-scale coal-water slurry (CWS)-fired space heating system will be a scale-up of a CWS-fired residential warm-air heating system developed by Tecogen under contract to the Department of Energy, Pittsburgh Energy Technology Center. This system included a patented nonslagging combustor known as IRIS, for Inertial Reactor with Internal Separation. This combustion technology, which has demonstrated high combustion efficiency using CWS fuels at input rates of 100,000 Btu/hr, will be scaled to operate at 2 to 5 millon Btu/hr. Along with the necessary fuel storage and delivery, heat recovery, and control equipment, the system will include pollution control devices to meet targeted values of NO{sub x}, S0{sub 2}, and particulate emissions. In general, the system will be designed to match the reliability, safety, turndown, and ignition performance of gas or oil-fired systems.

  2. Commercial-scale recycling of NdFeB-type magnets with grain boundary modification yields products with 'designer properties' that exceed those of starting materials.

    PubMed

    Zakotnik, M; Tudor, C O

    2015-10-01

    NdFeB-type magnets dominate the market for high performance magnetic materials, yet production of 'virgin' magnets via mining is environmentally, financially and energetically costly. Hence, interest is growing in 'magnet to magnet' recycling schemes that offer the potential for cheaper, more environmentally-friendly solutions to the world's growing appetite for rare-earth based magnetic materials. Unfortunately, previously described recycling processes only partially capitalise on this potential, because the methods described to date are limited to 'laboratory scale' or operate only under ideal conditions and result in products that fail to recapture the coercivity of the starting, scrap materials. Herein, we report a commercial scale process (120 kg batches) that completely recovers the properties of the starting scrap magnets. Indeed, 'grain boundary modification', via careful addition of a proprietary mix of blended elements, produces magnets with 'designer properties' that can exceed those of the starting materials and can be closely tailored to meet a wide variety of end-user applications, including high-coercivity (>2000 kA/m), sintered magnets suitable for motor applications.

  3. Triclocarban, triclosan and its transformation product methyl triclosan in native earthworm species four years after a commercial-scale biosolids application.

    PubMed

    Macherius, André; Lapen, David R; Reemtsma, Thorsten; Römbke, Jörg; Topp, Edward; Coors, Anja

    2014-02-15

    Triclocarban (TCC), triclosan (TCS) and methyl triclosan (Me-TCS) were detected in soil and the native population of earthworms of an agricultural field in Ottawa, Canada, about four years after a commercial-scale application of biosolids. In soil that received biosolids, TCC and TCS were detected at median concentrations of 13.0 and 1.5 ng/g soil (d.w.), respectively, while Me-TCS, the transformation product of triclosan, was detected at a six-fold higher median concentration than its precursor. In earthworms collected at the biosolids-amended field-plot about four years post application, Me-TCS was also detected at higher concentrations (26 to 114 ng/g tissue d.w.) than TCS (16-51 ng/g) and TCC (4-53 ng/g). These data provide evidence that not only parent compounds but also their transformation products need to be considered in faunal bioaccumulation studies. Moreover, the preliminary results for pooled earthworm samples from different ecological groups suggest that the degree of bioaccumulation of biosolids-associated contaminants may depend on the habitat and feeding behavior of the organisms.

  4. Development and testing of a commercial-scale coal-fired combustion system: Phase 2, Quarterly technical progress report No. 7, April 1, 1992--June 20, 1992

    SciTech Connect

    Litka, A.F.; Breault, R.W.

    1992-08-01

    The objective of this program is to demonstrate the technical and economic viability of a coal-fired combustion system for the commercial sector. The commercial-scale coal-water slurry (CWS) fired space heating system will be a scale-up of a CWS-fired residential warm-air heating system developed by Tecogen Inc. under contract to the Department of Energy (DOE), Pittsburgh Energy Technology Center. This system included a patented nonslagging combustor known as IRIS, for Inertial Reactor with Internal Separation. This combustion technology, which has demonstrated high combustion efficiency using CWS fuels at input rates of 100,000 Btu/hr. will be scaled to operate at 2 to 5 million Btu/hr. Along with the necessary fuel storage and delivery, heat recovery, and control equipment, the system will include pollution control devices to meet targeted values of NO{sub x}, SO{sub 2}, and particulate emissions. In general, the system will be designed to match the reliability, safety, turndown, and ignition performance of gas or oil-fired systems. This report documents the work carried out in the seventh quarter of the program. During this period, proof-of-concept tests aimed at eliminating ash accumulation in the combustor and boiler were conducted. A compressed air soot blower system was installed on the boiler and combustor design changes implemented to reduced direct impingement of slurry on the upper chamber partition. As part of this testing, emission performance goals using Kentucky Hazard Prince Mine coal water slurry were met. Also, during this period the automatic control system for the system was installed and operation with this system was implemented.

  5. Techno-economic analysis for incorporating a liquid-liquid extraction system to remove acetic acid into a proposed commercial scale biorefinery.

    PubMed

    Aghazadeh, Mahdieh; Engelberth, Abigail S

    2016-07-08

    Mitigating the effect of fermentation inhibitors in bioethanol plants can have a great positive impact on the economy of this industry. Liquid-liquid extraction (LLE) using ethyl acetate is able to remove fermentation inhibitors-chiefly, acetic acid-from an aqueous solution used to produce bioethanol. The fermentation broth resulting from LLE has higher performance for ethanol yield and its production rate. Previous techno-economic analyses focused on second-generation biofuel production did not address the impact of removing the fermentation inhibitors on the economic performance of the biorefinery. A comprehensive analysis of applying a separation system to mitigate the fermentation inhibition effect and to provide an analysis on the economic impact of removal of acetic acid from corn stover hydrolysate on the overall revenue of the biorefinery is necessary. This study examines the pros and cons associated with implementing LLE column along with the solvent recovery system into a commercial scale bioethanol plant. Using details from the NREL-developed model of corn stover biorefinery, the capital costs associated with the equipment and the operating cost for the use of solvent were estimated and the results were compared with the profit gain due to higher ethanol production. Results indicate that the additional capital will add 1% to the total capital and manufacturing cost will increase by 5.9%. The benefit arises from the higher ethanol production rate and yield as a consequence of inhibitor extraction and results in a $0.35 per gallon reduction in the minimum ethanol selling price (MESP). © 2016 American Institute of Chemical Engineers Biotechnol. Prog., 32:971-977, 2016.

  6. Effect of commercial-scale high-temperature, short-time pasteurization on the viability of Mycobacterium paratuberculosis in naturally infected cows' milk.

    PubMed

    Grant, Irene R; Hitchings, Edward I; McCartney, Alan; Ferguson, Fiona; Rowe, Michael T

    2002-02-01

    Raw cows' milk naturally infected with Mycobacterium paratuberculosis was pasteurized with an APV HXP commercial-scale pasteurizer (capacity 2,000 liters/h) on 12 separate occasions. On each processing occasion, milk was subjected to four different pasteurization treatments, viz., 73 degrees C for 15 s or 25 s with and without prior homogenization (2,500 lb/in(2) in two stages), in an APV Manton Gaulin KF6 homogenizer. Raw and pasteurized milk samples were tested for M. paratuberculosis by immunomagnetic separation (IMS)-PCR (to detect the presence of bacteria) and culture after decontamination with 0.75% (wt/vol) cetylpyridinium chloride for 5 h (to confirm bacterial viability). On 10 of the 12 processing occasions, M. paratuberculosis was detectable by IMS-PCR, culture, or both in either raw or pasteurized milk. Overall, viable M. paratuberculosis was cultured from 4 (6.7%) of 60 raw and 10 (6.9%) of 144 pasteurized milk samples. On one processing day, in particular, M. paratuberculosis appeared to have been present in greater abundance in the source raw milk (evidenced by more culture positives and stronger PCR signals), and on this occasion, surviving M. paratuberculosis bacteria were isolated from milk processed by all four heat treatments, i.e., 73 degrees C for 15 and 25 s with and without prior homogenization. On one other occasion, surviving M. paratuberculosis bacteria were isolated from an unhomogenized milk sample that had been heat treated at 73 degrees C for 25 s. Results suggested that homogenization increases the lethality of subsequent heat treatment to some extent with respect to M. paratuberculosis, but the extended 25-s holding time at 73 degrees C was found to be no more effective at killing M. paratuberculosis than the standard 15-s holding time. This study provides clear evidence that M. paratuberculosis bacteria in naturally infected milk are capable of surviving commercial high-temperature, short-time pasteurization if they are present in

  7. Effect of Commercial-Scale High-Temperature, Short-Time Pasteurization on the Viability of Mycobacterium paratuberculosis in Naturally Infected Cows' Milk

    PubMed Central

    Grant, Irene R.; Hitchings, Edward I.; McCartney, Alan; Ferguson, Fiona; Rowe, Michael T.

    2002-01-01

    Raw cows' milk naturally infected with Mycobacterium paratuberculosis was pasteurized with an APV HXP commercial-scale pasteurizer (capacity 2,000 liters/h) on 12 separate occasions. On each processing occasion, milk was subjected to four different pasteurization treatments, viz., 73°C for 15 s or 25 s with and without prior homogenization (2,500 lb/in2 in two stages), in an APV Manton Gaulin KF6 homogenizer. Raw and pasteurized milk samples were tested for M. paratuberculosis by immunomagnetic separation (IMS)-PCR (to detect the presence of bacteria) and culture after decontamination with 0.75% (wt/vol) cetylpyridinium chloride for 5 h (to confirm bacterial viability). On 10 of the 12 processing occasions, M. paratuberculosis was detectable by IMS-PCR, culture, or both in either raw or pasteurized milk. Overall, viable M. paratuberculosis was cultured from 4 (6.7%) of 60 raw and 10 (6.9%) of 144 pasteurized milk samples. On one processing day, in particular, M. paratuberculosis appeared to have been present in greater abundance in the source raw milk (evidenced by more culture positives and stronger PCR signals), and on this occasion, surviving M. paratuberculosis bacteria were isolated from milk processed by all four heat treatments, i.e., 73°C for 15 and 25 s with and without prior homogenization. On one other occasion, surviving M. paratuberculosis bacteria were isolated from an unhomogenized milk sample that had been heat treated at 73°C for 25 s. Results suggested that homogenization increases the lethality of subsequent heat treatment to some extent with respect to M. paratuberculosis, but the extended 25-s holding time at 73°C was found to be no more effective at killing M. paratuberculosis than the standard 15-s holding time. This study provides clear evidence that M. paratuberculosis bacteria in naturally infected milk are capable of surviving commercial high-temperature, short-time pasteurization if they are present in raw milk in sufficient numbers

  8. Reference Services.

    ERIC Educational Resources Information Center

    Bunge, Charles A.

    1999-01-01

    Discusses library reference services. Topics include the historical development of reference services; instruction in library use, particularly in college and university libraries; guidance; information and referral services and how they differ from traditional question-answering service; and future concerns, including user fees and the planning…

  9. Reference Assessment

    ERIC Educational Resources Information Center

    Bivens-Tatum, Wayne

    2006-01-01

    This article presents interesting articles that explore several different areas of reference assessment, including practical case studies and theoretical articles that address a range of issues such as librarian behavior, patron satisfaction, virtual reference, or evaluation design. They include: (1) "Evaluating the Quality of a Chat Service"…

  10. Reference Revolutions.

    ERIC Educational Resources Information Center

    Mason, Marilyn Gell

    1998-01-01

    Describes developments in Online Computer Library Center (OCLC) electronic reference services. Presents a background on networked cataloging and the initial implementation of reference services by OCLC. Discusses the introduction of OCLC FirstSearch service, which today offers access to over 65 databases, future developments in integrated…

  11. Time-Temperature-Tolerance (T. T. T.) of On-Board Frozen Tuna During Subsequent On-Land Frozen Storage with Particular Reference to Commercial Scale Trial-II

    NASA Astrophysics Data System (ADS)

    Tanaka, Takeo; Hamamoto, Yûkichi; Nishiwaki, Kôji

    As described in the preceding paper 1), there is a demand in the tuna industry from the view point of energy saving for setting up T. T. T. of on-board frozen tuna during on-land frozen storage. Three groups of tuna being composed of three different species, yellowfin (YF), southern bluefin (SB) and bigeye (BE) tuna which had been frozen on-board commercially were further stored experimentally at -40, - 30 and -20°C. K1 value (one of freshness index for fish) and K2 value (one of taste component index for fish meat) were used as quality index for T. T. T. decision. Results are as follows : Both values of three tunas examined did not change appreciably throughout storage at any temperature of -20, - 30 and -40°C. These findings indicated that T. T. T. of YF and SB was estimated to be 6 months∗ at least, and that of BE to be 17 months∗ at least as far as it was judged on bases of K1) and K2 values. (Asterisks indicate merely the length of the experimental storage, ac tual T. T. T. therefore, must be longer).

  12. Time-Temperature-Tolerance(T. T. T.) of On-Board Frozen Tuna During Subsequent On-Land Frozen Storage with Particular Reference to Commercial Scale Trial-I

    NASA Astrophysics Data System (ADS)

    Tanaka, Takeo; Takahashi, Kenji; Nishiwaki, Koji

    This study was undertaken to meet the demand of the tuna industry for the definite criterion of T. T. T. of on-board frozen tuna during on-land frozen storage, from the veiw point of energy saving. Yellowfin (YF), southern bluefin (SB) and bigeye (BE) tuna which had been frozen-stored on board in semi-dressed form, excluding gills and viscera, commercially were further stored experimentally at -40, -30 and -20°C on the premise that a target of commercial storage period was 6 months. Decision on tolerance limits was given by degree of discoloration of the meat (met-myoglobin ratio). Results are as follows : T. T. T. of YF and SB was estimated to be 6 months∗ and that of BE to be 17 months∗ at -40°C, and that of the three tunas examined to be 6 months∗ at -30°C. T. T. T. of YF and SB was estimated to be 1.5 and 4-5 months (2-3 and 5 months in the case of meat block), respectively, and that of BE to be one month at -20°C. (Asterisks indicate merely the length of the experimental storage, actual T. T. T therefore, must be longer).

  13. Ready Reference.

    ERIC Educational Resources Information Center

    Koltay, Emery

    1999-01-01

    Includes the following ready reference information: "Publishers' Toll-Free Telephone Numbers"; "How to Obtain an ISBN (International Standard Book Number)"; "How to Obtain an ISSN (International Standard Serial Number)"; and "How to Obtain an SAN (Standard Address Number)". (AEF)

  14. Poroelastic references

    SciTech Connect

    Morency, Christina

    2014-12-12

    This file contains a list of relevant references on the Biot theory (forward and inverse approaches), the double-porosity and dual-permeability theory, and seismic wave propagation in fracture porous media, in RIS format, to approach seismic monitoring in a complex fractured porous medium such as Brady?s Geothermal Field.

  15. Ready Reference.

    ERIC Educational Resources Information Center

    Koltay, Emery

    2001-01-01

    Includes four articles that relate to ready reference, including a list of publishers' toll-free telephone numbers and Web sites; how to obtain an ISBN (International Standard Book Number) and an ISSN (International Standard Serial Number); and how to obtain an SAN (Standard Address Number), for organizations that are involved in the book…

  16. Tri-State Synfuels Project Commercial Scale Coal Test: Volume 1. Selection of camp 1 coal. [Proposed Henderson, Kentucky coal to gasoline plant; selection and testing of coal supplies

    SciTech Connect

    Not Available

    1982-06-01

    This report focuses on the rationale for selecting Camp 1 coal for a commercial scale gasification test conducted at the Sasol One Plant. The initial coal quality evaluation consisted primarily of The Pennsylvania State University coal data from Illinois Basin Counties. In November 1980, a preliminary collection of Illinois Basin coal quality data was developed to support the selection of coals for potential plant supply and full scale commercial testing. The total sample and coarse and fine fractions were analyzed. Lurgi and Sasol examined the list and gave their reasons for selection but they had not examined the samples in their laboratories. In December 1980, the list of potential source mines for the 22,000 short ton sample of raw coal for the test was narrowed to three. The mines were Camp 1, Ken and Providence. The reasons for this selection are given. The three candidate mines were again sampled and representative splits of the run-of-mine samples were flown to Lurgi and to Sasol for examination. The Lurgi laboratory report indicated that both Camp 1 and Ken mine samples would qualify as suitable gasifier feed coals. Sasol concluded from an examination of the November report data that Camp 1 and Ken mine samples would be preferable since the free swelling indices are not excessive. Paul Weir Company examined the data and recommended Camp 1 mine since it operates in the seams contiguous to other potential candidate reserve sites and has the ability to transport the mine sample by belt to a barge loading facility to limit production of fines. The final selection of the Camp 1 mine for the test shipment resulted from considerations given in the report.

  17. Reference Frames and Relativity.

    ERIC Educational Resources Information Center

    Swartz, Clifford

    1989-01-01

    Stresses the importance of a reference frame in mechanics. Shows the Galilean transformation in terms of relativity theory. Discusses accelerated reference frames and noninertial reference frames. Provides examples of reference frames with diagrams. (YP)

  18. Reference Service Policy Statement.

    ERIC Educational Resources Information Center

    Young, William F.

    This reference service policy manual provides general guidelines to encourage reference service of the highest possible quality and to insure uniform practice. The policy refers only to reference service in the University Libraries and is intended for use in conjunction with other policies and procedures issued by the Reference Services Division.…

  19. Reach for Reference. Four Recent Reference Books

    ERIC Educational Resources Information Center

    Safford, Barbara Ripp

    2004-01-01

    This article provides descriptions of four new science and technology encyclopedias that are appropriate for inclusion in upper elementary and/or middle school reference collections. "The Macmillan Encyclopedia of Weather" (Stern, Macmillan Reference/Gale), a one-volume encyclopedia for upper elementary and middle level students, is a…

  20. Fundamentals of Reference

    ERIC Educational Resources Information Center

    Mulac, Carolyn M.

    2012-01-01

    The all-in-one "Reference reference" you've been waiting for, this invaluable book offers a concise introduction to reference sources and services for a variety of readers, from library staff members who are asked to work in the reference department to managers and others who wish to familiarize themselves with this important area of…

  1. Live, Digital Reference.

    ERIC Educational Resources Information Center

    Kenney, Brian

    2002-01-01

    Discusses digital reference services, also known as virtual reference, chat reference, or online reference, based on a round table discussion at the 2002 American Library Association annual conference in Atlanta. Topics include numbers and marketing; sustainability; competition and models; evaluation methods; outsourcing; staffing and training;…

  2. Statistical Reference Datasets

    National Institute of Standards and Technology Data Gateway

    Statistical Reference Datasets (Web, free access)   The Statistical Reference Datasets is also supported by the Standard Reference Data Program. The purpose of this project is to improve the accuracy of statistical software by providing reference datasets with certified computational results that enable the objective evaluation of statistical software.

  3. Genetics Home Reference

    MedlinePlus

    Skip Navigation Bar Home Current Issue Past Issues Genetics Home Reference Past Issues / Spring 2007 Table of ... of this page please turn Javascript on. The Genetics Home Reference (GHR) Web site — ghr.nlm.nih. ...

  4. Herbal reference standards.

    PubMed

    Schwarz, Michael; Klier, Bernhard; Sievers, Hartwig

    2009-06-01

    This review describes the current definitions and regulatory requirements that apply to reference standards that are used to analyse herbal products. It also describes and discusses the current use of reference substances and reference extracts in the European and United States pharmacopoeias.

  5. Academic Library Reference Services.

    ERIC Educational Resources Information Center

    Batt, Fred

    This examination of the philosophy and objectives of academic library reference services provides an overview of the major reference approaches to fulfilling the following primary objectives of reference services: (1) providing accurate answers to patrons' questions and/or helping patrons find sources to pursue their research needs; (2) building…

  6. Selection of the reference steam generator for the advanced liquid metal reactor

    SciTech Connect

    Loewen, Eric P.; Boardman, Chuck

    2007-07-01

    In February 2006 President Bush announced the Advanced Energy Initiative, which included the Department of Energy's (DOE) Global Nuclear Energy Partnership (GNEP). GNEP has seven broad goals; one of the major elements being to develop and deploy advanced nuclear fuel recycling technology that includes consuming spent nuclear fuel in an Advanced Recycling Reactor (ARR). DOE is contemplating accelerating the deployment of these technologies to achieve the construction of a commercial scale application of these technologies. DOE now defines this approach as 'two simultaneous tracks: (1) deployment of commercial scale facilities for which advanced technologies are available now or in the near future, and (2) further research and development of transmutation fuels technologies'. GEHitachi Nuclear Energy Americas LLC (GHNEA) believes an integrated technical solution is achievable in the near term to accelerate the commercial demonstration of GNEP infrastructure. The GHNEA ARR concept involves a single integrated recycling facility sized to service a single reactor module ARR capable of destroying light water and fast reactor sourced actinides. This paper describes the bases and rationale behind the selection of the helical coil steam generator (HCSG) as the reference steam generator concept for the ALMR and S-PRISM reactor concepts. (authors)

  7. References for marine science

    NASA Astrophysics Data System (ADS)

    1990-06-01

    Standard and Reference Materials for Marine Science, National Oceanic and Atmospheric Administration Technical Memo OMA-51 (2nd edition, 434 pp.), by A. Y. Cantillo, is now available. This compilation of reference materials was prepared at the request of the Group of Experts on Standards and Reference Materials and was printed by NOAA. GESREM is sponsored by the International Atomic Energy Agency, the Intergovernmental Oceanographic Commission, and the United Nations Program.Reference materials are included on ashes, gases, instrument performance materials, oils, physical properties, rocks, sediments, sludges, tissues and waters. For each reference material, source, description and preparation, analyses and values, cost, references, and comments are given. Indices are included for elements, isotopes and organic compounds. Cross references to Chemical Abstracts Service registry numbers and alternate names and chemical structures of organic compounds are also provided.

  8. High frequency reference electrode

    DOEpatents

    Kronberg, James W.

    1994-01-01

    A high frequency reference electrode for electrochemical experiments comprises a mercury-calomel or silver-silver chloride reference electrode with a layer of platinum around it and a layer of a chemically and electrically resistant material such as TEFLON around the platinum covering all but a small ring or "halo" at the tip of the reference electrode, adjacent to the active portion of the reference electrode. The voltage output of the platinum layer, which serves as a redox electrode, and that of the reference electrode are coupled by a capacitor or a set of capacitors and the coupled output transmitted to a standard laboratory potentiostat. The platinum may be applied by thermal decomposition to the surface of the reference electrode. The electrode provides superior high-frequency response over conventional electrodes.

  9. High frequency reference electrode

    DOEpatents

    Kronberg, J.W.

    1994-05-31

    A high frequency reference electrode for electrochemical experiments comprises a mercury-calomel or silver-silver chloride reference electrode with a layer of platinum around it and a layer of a chemically and electrically resistant material such as TEFLON around the platinum covering all but a small ring or halo' at the tip of the reference electrode, adjacent to the active portion of the reference electrode. The voltage output of the platinum layer, which serves as a redox electrode, and that of the reference electrode are coupled by a capacitor or a set of capacitors and the coupled output transmitted to a standard laboratory potentiostat. The platinum may be applied by thermal decomposition to the surface of the reference electrode. The electrode provides superior high-frequency response over conventional electrodes. 4 figs.

  10. Reference Model 6 (RM6): Oscillating Wave Energy Converter.

    SciTech Connect

    Bull, Diana L; Smith, Chris; Jenne, Dale Scott; Jacob, Paul; Copping, Andrea; Willits, Steve; Fontaine, Arnold; Brefort, Dorian; Gordon, Margaret Ellen; Copeland, Robert; Jepsen, Richard Alan

    2014-10-01

    This report is an addendum to SAND2013-9040: Methodology for Design and Economic Analysis of Marine Energy Conversion (MEC) Technologies. This report describes an Oscillating Water Column Wave Energy Converter reference model design in a complementary manner to Reference Models 1-4 contained in the above report. In this report, a conceptual design for an Oscillating Water Column Wave Energy Converter (WEC) device appropriate for the modeled reference resource site was identified, and a detailed backward bent duct buoy (BBDB) device design was developed using a combination of numerical modeling tools and scaled physical models. Our team used the methodology in SAND2013-9040 for the economic analysis that included costs for designing, manufacturing, deploying, and operating commercial-scale MEC arrays, up to 100 devices. The methodology was applied to identify key cost drivers and to estimate levelized cost of energy (LCOE) for this RM6 Oscillating Water Column device in dollars per kilowatt-hour ($/kWh). Although many costs were difficult to estimate at this time due to the lack of operational experience, the main contribution of this work was to disseminate a detailed set of methodologies and models that allow for an initial cost analysis of this emerging technology. This project is sponsored by the U.S. Department of Energy's (DOE) Wind and Water Power Technologies Program Office (WWPTO), within the Office of Energy Efficiency & Renewable Energy (EERE). Sandia National Laboratories, the lead in this effort, collaborated with partners from National Laboratories, industry, and universities to design and test this reference model.

  11. Reference Model 5 (RM5): Oscillating Surge Wave Energy Converter

    SciTech Connect

    Yu, Y. H.; Jenne, D. S.; Thresher, R.; Copping, A.; Geerlofs, S.; Hanna, L. A.

    2015-01-01

    This report is an addendum to SAND2013-9040: Methodology for Design and Economic Analysis of Marine Energy Conversion (MEC) Technologies. This report describes an Oscillating Water Column Wave Energy Converter (OSWEC) reference model design in a complementary manner to Reference Models 1-4 contained in the above report. A conceptual design for a taut moored oscillating surge wave energy converter was developed. The design had an annual electrical power of 108 kilowatts (kW), rated power of 360 kW, and intended deployment at water depths between 50 m and 100 m. The study includes structural analysis, power output estimation, a hydraulic power conversion chain system, and mooring designs. The results were used to estimate device capital cost and annual operation and maintenance costs. The device performance and costs were used for the economic analysis, following the methodology presented in SAND2013-9040 that included costs for designing, manufacturing, deploying, and operating commercial-scale MEC arrays up to 100 devices. The levelized cost of energy estimated for the Reference Model 5 OSWEC, presented in this report, was for a single device and arrays of 10, 50, and 100 units, and it enabled the economic analysis to account for cost reductions associated with economies of scale. The baseline commercial levelized cost of energy estimate for the Reference Model 5 device in an array comprised of 10 units is $1.44/kilowatt-hour (kWh), and the value drops to approximately $0.69/kWh for an array of 100 units.

  12. Preparing the references.

    PubMed

    Peh, W C G; Ng, K H

    2009-07-01

    In a scientific paper, the references serve to provide background information and allow the researcher to compare and contrast the work of others in relation to his own study. Authors are responsible for the accuracy of all references cited. The references quoted should be easily accessible and retrievable by anyone wishing to obtain further information. There is a strong preference for citing journal articles listed in PubMed. The two major reference format systems are the Vancouver and Harvard systems, with increasing preference for the Vancouver system. Authors should adhere exactly to the instructions to authors of the target journal.

  13. Reference Point Heterogeneity

    PubMed Central

    Terzi, Ayse; Koedijk, Kees; Noussair, Charles N.; Pownall, Rachel

    2016-01-01

    It is well-established that, when confronted with a decision to be taken under risk, individuals use reference payoff levels as important inputs. The purpose of this paper is to study which reference points characterize decisions in a setting in which there are several plausible reference levels of payoff. We report an experiment, in which we investigate which of four potential reference points: (1) a population average payoff level, (2) the announced expected payoff of peers in a similar decision situation, (3) a historical average level of earnings that others have received in the same task, and (4) an announced anticipated individual payoff level, best describes decisions in a decontextualized risky decision making task. We find heterogeneity among individuals in the reference points they employ. The population average payoff level is the modal reference point, followed by experimenter's stated expectation of a participant's individual earnings, followed in turn by the average earnings of other participants in previous sessions of the same experiment. A sizeable share of individuals show multiple reference points simultaneously. The reference point that best fits the choices of the individual is not affected by a shock to her income. PMID:27672374

  14. Marketing Reference Services.

    ERIC Educational Resources Information Center

    Norman, O. Gene

    1995-01-01

    Relates the marketing concept to library reference services. Highlights include a review of the literature and an overview of marketing, including research, the marketing mix, strategic plan, marketing plan, and marketing audit. Marketing principles are applied to reference services through the marketing mix elements of product, price, place, and…

  15. An Online Reference System.

    ERIC Educational Resources Information Center

    Chisman, Janet; Treat, William

    1984-01-01

    Describes a computer aid developed to assist in academic library reference service using the DataPhase Circulation System, an automated system that features full cataloging records in database and permits local programing. Access points (subject, type of reference work, course) and database structure and user screens are highlighted. (EJS)

  16. China Connections Reference Book.

    ERIC Educational Resources Information Center

    Kalat, Marie B.; Hoermann, Elizabeth F.

    This reference book focuses on six aspects of the geography of the People's Republic of China. They are: territory, governing units, population and land use, waterways, land forms, and climates. Designed as a primary reference, the book explains how the Chinese people and their lifestyles are affected by China's geography. Special components…

  17. Rethinking Virtual Reference

    ERIC Educational Resources Information Center

    Tenopir, Carol

    2004-01-01

    Virtual reference services seem a natural extension of libraries digital collections and the emphasis on access to the library anytime, anywhere. If patrons use the library from home, it makes sense to provide them with person-to-person online reference. The Library of Congress (LC), OCLC, and several large library systems have developed and…

  18. Reference Point Heterogeneity.

    PubMed

    Terzi, Ayse; Koedijk, Kees; Noussair, Charles N; Pownall, Rachel

    2016-01-01

    It is well-established that, when confronted with a decision to be taken under risk, individuals use reference payoff levels as important inputs. The purpose of this paper is to study which reference points characterize decisions in a setting in which there are several plausible reference levels of payoff. We report an experiment, in which we investigate which of four potential reference points: (1) a population average payoff level, (2) the announced expected payoff of peers in a similar decision situation, (3) a historical average level of earnings that others have received in the same task, and (4) an announced anticipated individual payoff level, best describes decisions in a decontextualized risky decision making task. We find heterogeneity among individuals in the reference points they employ. The population average payoff level is the modal reference point, followed by experimenter's stated expectation of a participant's individual earnings, followed in turn by the average earnings of other participants in previous sessions of the same experiment. A sizeable share of individuals show multiple reference points simultaneously. The reference point that best fits the choices of the individual is not affected by a shock to her income.

  19. Genetics Home Reference: nephronophthisis

    MedlinePlus

    ... these are often referred to as nephronophthisis -associated ciliopathies. For example, Senior-Løken syndrome is characterized by ... Nephronophthisis Patient Support and Advocacy Resources (2 links) Ciliopathy Alliance National Kidney Foundation GeneReviews (1 link) Nephronophthisis ...

  20. Value of Information References

    SciTech Connect

    Morency, Christina

    2014-12-12

    This file contains a list of relevant references on value of information (VOI) in RIS format. VOI provides a quantitative analysis to evaluate the outcome of the combined technologies (seismology, hydrology, geodesy) used to monitor Brady's Geothermal Field.

  1. EPA QUICK REFERENCE GUIDES

    EPA Science Inventory

    EPA Quick Reference Guides are compilations of information on chemical and biological terrorist agents. The information is presented in consistent format and includes agent characteristics, release scenarios, health and safety data, real-time field detection, effect levels, samp...

  2. Selecting a reference object.

    PubMed

    Miller, Jared E; Carlson, Laura A; Hill, Patrick L

    2011-07-01

    One way to describe the location of an object is to relate it to another object. Often there are many nearby objects, each of which could serve as a candidate to be the reference object. A common theoretical assumption is that features that make a given object salient relative to the candidate set are instrumental in determining which is selected. The current research tests this assumption, assessing the relative importance of spatial, perceptual, and functional-interactive features. Three experiments demonstrated that spatial features have the strongest influence on reference object selection, with the perceptual feature of color playing no significant role. Functional-interactive features were shown to be spatially dependent, having an influence only when the spatial configuration enabled an interaction between the located object and the reference object. These findings challenge the common perspective that salience in and of itself dictates reference object selection and argue for a reliance on spatial features.

  3. Genetics Home Reference

    MedlinePlus

    ... MENU Toggle navigation Home Page Search Share: Email Facebook Twitter Home Health Conditions Genes Chromosomes & mtDNA Resources Help Me Understand Genetics Genetics Home Reference provides consumer-friendly information about the effects of genetic variation ...

  4. Enterprise Reference Library

    NASA Technical Reports Server (NTRS)

    Bickham, Grandin; Saile, Lynn; Havelka, Jacque; Fitts, Mary

    2011-01-01

    Introduction: Johnson Space Center (JSC) offers two extensive libraries that contain journals, research literature and electronic resources. Searching capabilities are available to those individuals residing onsite or through a librarian s search. Many individuals have rich collections of references, but no mechanisms to share reference libraries across researchers, projects, or directorates exist. Likewise, information regarding which references are provided to which individuals is not available, resulting in duplicate requests, redundant labor costs and associated copying fees. In addition, this tends to limit collaboration between colleagues and promotes the establishment of individual, unshared silos of information The Integrated Medical Model (IMM) team has utilized a centralized reference management tool during the development, test, and operational phases of this project. The Enterprise Reference Library project expands the capabilities developed for IMM to address the above issues and enhance collaboration across JSC. Method: After significant market analysis for a multi-user reference management tool, no available commercial tool was found to meet this need, so a software program was built around a commercial tool, Reference Manager 12 by The Thomson Corporation. A use case approach guided the requirements development phase. The premise of the design is that individuals use their own reference management software and export to SharePoint when their library is incorporated into the Enterprise Reference Library. This results in a searchable user-specific library application. An accompanying share folder will warehouse the electronic full-text articles, which allows the global user community to access full -text articles. Discussion: An enterprise reference library solution can provide a multidisciplinary collection of full text articles. This approach improves efficiency in obtaining and storing reference material while greatly reducing labor, purchasing and

  5. Membrane reference electrode

    DOEpatents

    Redey, L.; Bloom, I.D.

    1988-01-21

    A reference electrode utilizes a small thin, flat membrane of a highly conductive glass placed on a small diameter insulator tube having a reference material inside in contact with an internal voltage lead. When the sensor is placed in a non-aqueous ionic electrolytic solution, the concentration difference across the glass membrane generates a low voltage signal in precise relationship to the concentration of the species to be measured, with high spatial resolution. 2 figs.

  6. Membrane reference electrode

    DOEpatents

    Redey, Laszlo; Bloom, Ira D.

    1989-01-01

    A reference electrode utilizes a small thin, flat membrane of a highly conductive glass placed on a small diameter insulator tube having a reference material inside in contact with an internal voltage lead. When the sensor is placed in a non-aqueous ionic electrolytic solution, the concentration difference across the glass membrane generates a low voltage signal in precise relationship to the concentration of the species to be measured with high spatial resolution.

  7. Precision displacement reference system

    DOEpatents

    Bieg, Lothar F.; Dubois, Robert R.; Strother, Jerry D.

    2000-02-22

    A precision displacement reference system is described, which enables real time accountability over the applied displacement feedback system to precision machine tools, positioning mechanisms, motion devices, and related operations. As independent measurements of tool location is taken by a displacement feedback system, a rotating reference disk compares feedback counts with performed motion. These measurements are compared to characterize and analyze real time mechanical and control performance during operation.

  8. Reference Man anatomical model

    SciTech Connect

    Cristy, M.

    1994-10-01

    The 70-kg Standard Man or Reference Man has been used in physiological models since at least the 1920s to represent adult males. It came into use in radiation protection in the late 1940s and was developed extensively during the 1950s and used by the International Commission on Radiological Protection (ICRP) in its Publication 2 in 1959. The current Reference Man for Purposes of Radiation Protection is a monumental book published in 1975 by the ICRP as ICRP Publication 23. It has a wealth of information useful for radiation dosimetry, including anatomical and physiological data, gross and elemental composition of the body and organs and tissues of the body. The anatomical data includes specified reference values for an adult male and an adult female. Other reference values are primarily for the adult male. The anatomical data include much data on fetuses and children, although reference values are not established. There is an ICRP task group currently working on revising selected parts of the Reference Man document.

  9. Nuclear-driven flashlamp pumping of the atomic iodine laser

    SciTech Connect

    Miley, G.H.

    1992-03-01

    This report is a study of the atomic iodine laser pumped with nuclear- excited XeBr fluorescence. Preliminary experiments, conducted in the TRIGA reactor investigated the fluorescence of the excimer XeBr under nuclear pumping with {sup 10}B and {sup 3}He, for use as a flashlamp gas to stimulate the laser. These measurements included a determination of the fluorescence efficiency (light emitted in the wavelength region of interest, divided by energy deposited in the gas) of XeBr under nuclear pumping, with varying excimer mixtures. Maximum fluorescence efficiencies were approximately 1%. In order to better understand XeBr under nuclear excitation, a kinetics model of the system was prepared. The model generated the time-dependant concentrations of 20 reaction species for three pulse sizes, a TRIGA pulse, a fast burst reactor pulse, and an e-beam pulse. The modeling results predicted fluorescence efficiencies significantly higher (peak efficiencies of approximately 10%) than recorded in the fluorescence experiments. The cause of this discrepancy was not fully determined. A ray tracing computer model was also prepared to evaluate the efficiency with which nuclear-induced fluorescence generated in one cavity of a laser could be coupled into another cavity containing an iodine lasant. Finally, an experimental laser cell was constructed to verify that nuclear-induced XeBr fluorescence could be used to stimulate a laser. Lasing was achieved at 1.31 micron in the TRIGA using C{sub 3}F{sub 7}I, a common iodine lasant. Peak laser powers were approximately 20 mW. Measured flashlamp pump powers at threshold agreed well with literature values, as did lasant pressure dependency on laser operation.

  10. Application of the SELECS methodology to evaluate socioeconomic and environmental impacts of commercial-scale coal liquefaction plants at six potential sites in Kentucky. Final report from the study on development of environmental guidelines for the selection of sites for fossil energy conversion facilities

    SciTech Connect

    Northrop, G. M.; D'Ambra, C. A.

    1980-11-01

    Environmental and socioeconomic impacts likely to occur during the operational phase of two coal liquefaction processes have been evaluated with SELECS (Site Evaluation for Energy Conversion Systems) for each of six potential sites in Kentucky for commercial scale facilities capable of processing about 26,000 tons of coal per stream day. The processes considered in this evaluation are SRC-I, a direct liquefaction route with solid boiler fuel as the principal product, and Coal-to-Methanol-to-Gasoline, an indirect liquefaction route with transportation fuel as the primary product. For comparative purposes, the impacts of a 2-gigawatt coal-fired steam-electric power plant (with coal requirements comparable to the liquefaction facilities) and an automobile parts manufacturing plant (with employment requirements of 849, comparable to the liquefaction facilities) have also been evaluated at each site. At each site, impacts have been evaluated for one or two nearby cities or towns and four to six counties where significant impacts might be expected. The SELECS methodology affords a well-organized and efficient approach to collecting and assessing a large volume of data needed to comprehensively determine the potential socioeconomic and environmental impacts resulting from the implementation of commercial scale synfuel and other energy conversion facilities. This study has also shown that SELECS is equally applicable to determine the impacts of other facilities, such as automobile parts manufacturing. In brief, the SELECS methodology serves the purpose of objectively screening sites in order to choose one at which adverse impacts will be least, and/or to determine what aspect of a proposed facility might be modified to lessen impacts at a specific site.

  11. Setting reference targets

    SciTech Connect

    Ruland, R.E.

    1997-04-01

    Reference Targets are used to represent virtual quantities like the magnetic axis of a magnet or the definition of a coordinate system. To explain the function of reference targets in the sequence of the alignment process, this paper will first briefly discuss the geometry of the trajectory design space and of the surveying space, then continue with an overview of a typical alignment process. This is followed by a discussion on magnet fiducialization. While the magnetic measurement methods to determine the magnetic centerline are only listed (they will be discussed in detail in a subsequent talk), emphasis is given to the optical/mechanical methods and to the task of transferring the centerline position to reference targets.

  12. Multifunctional reference electrode

    DOEpatents

    Redey, L.; Vissers, D.R.

    1981-12-30

    A multifunctional, low mass reference electrode of a nickel tube, thermocouple means inside the nickel tube electrically insulated therefrom for measuring the temperature thereof, a housing surrounding the nickel tube, an electrolyte having a fixed sulfide ion activity between the housing and the outer surface of the nickel tube forming the nickel/nickel sulfide/sulfide half-cell are described. An ion diffusion barrier is associated with the housing in contact with the electrolyte. Also disclosed is a cell using the reference electrode to measure characteristics of a working electrode.

  13. Multifunctional reference electrode

    DOEpatents

    Redey, Laszlo; Vissers, Donald R.

    1983-01-01

    A multifunctional, low mass reference electrode of a nickel tube, thermocouple means inside the nickel tube electrically insulated therefrom for measuring the temperature thereof, a housing surrounding the nickel tube, an electrolyte having a fixed sulfide ion activity between the housing and the outer surface of the nickel tube forming the nickel/nickel sulfide/sulfide half-cell. An ion diffusion barrier is associated with the housing in contact with the electrolyte. Also disclosed is a cell using the reference electrode to measure characteristics of a working electrode.

  14. IERS Reference System.

    NASA Astrophysics Data System (ADS)

    Yokoyama, K.

    Present circumstances related to IERS activities are described from various points of view. The NASA Dynamics of Solid Earth (DOSE) program and the IERS intensive campaign proposed by J. Dickey of JPL are particularly interesting. It is important to implement international cooperation to establish a fundamental radio reference frame by carrying out global solution based on all geodetic observations, past and future. A precession and nutation model may be determined observationally with an accuracy of 0.2 - 0.3 mas in a few years. Then it will become possible to establish the radio reference frame with this accuracy.

  15. Aluminum reference electrode

    DOEpatents

    Sadoway, D.R.

    1988-08-16

    A stable reference electrode is described for use in monitoring and controlling the process of electrolytic reduction of a metal. In the case of Hall cell reduction of aluminum, the reference electrode comprises a pool of molten aluminum and a solution of molten cryolite, Na[sub 3]AlF[sub 6], wherein the electrical connection to the molten aluminum does not contact the highly corrosive molten salt solution. This is accomplished by altering the density of either the aluminum (decreasing the density) or the electrolyte (increasing the density) so that the aluminum floats on top of the molten salt solution. 1 fig.

  16. Aluminum reference electrode

    DOEpatents

    Sadoway, Donald R.

    1988-01-01

    A stable reference electrode for use in monitoring and controlling the process of electrolytic reduction of a metal. In the case of Hall cell reduction of aluminum, the reference electrode comprises a pool of molten aluminum and a solution of molten cryolite, Na.sub.3 AlF.sub.6, wherein the electrical connection to the molten aluminum does not contact the highly corrosive molten salt solution. This is accomplished by altering the density of either the aluminum (decreasing the density) or the electrolyte (increasing the density) so that the aluminum floats on top of the molten salt solution.

  17. NASCAP programmer's reference manual

    NASA Technical Reports Server (NTRS)

    Mandell, M. J.; Stannard, P. R.; Katz, I.

    1993-01-01

    The NASA Charging Analyzer Program (NASCAP) is a computer program designed to model the electrostatic charging of complicated three-dimensional objects, both in a test tank and at geosynchronous altitudes. This document is a programmer's reference manual and user's guide. It is designed as a reference to experienced users of the code, as well as an introduction to its use for beginners. All of the many capabilities of NASCAP are covered in detail, together with examples of their use. These include the definition of objects, plasma environments, potential calculations, particle emission and detection simulations, and charging analysis.

  18. Multimedia Reference Tools.

    ERIC Educational Resources Information Center

    Holzberg, Carol S.

    2001-01-01

    Presents suggestions for content-rich classroom encyclopedias on CO-ROM and DVD, including: the Encarta Reference Suite 2001; the 2001 Grolier Multimedia Encyclopedia, School Edition; the Britannica 2001 DVD; and the World Book 2001 Deluxe Edition, v5.0. (SM)

  19. Digital Reference Service.

    ERIC Educational Resources Information Center

    Mon, Lorri

    2000-01-01

    Discusses the increasing demand for digital reference services from government Web sites via email, and describes a partnership between the Government Printing Office and the federal depository library at the University of Illinois at Chicago to create electronic access to the Department of State Foreign Affairs Network (DOSFAN). (Author/LRW)

  20. Reflections on Reference Services.

    ERIC Educational Resources Information Center

    Brandt, Kerryn A.; And Others

    1996-01-01

    Describes programmatic changes in reference services at the Johns Hopkins University (Maryland) medical library and speculates on the future. Topics include institutional restructuring and consolidation; improvements in technology infrastructure; external economic pressure; and fiscal accountability, including library funding and cost center…

  1. Questions in Reference Interviews.

    ERIC Educational Resources Information Center

    White, Marilyn Domas

    1998-01-01

    Characterizes the questioning behavior in reference interviews preceding delegated online searches of bibliographic databases and relates it to questioning behavior in other types of interviews/settings. Compares questions asked by the information specialist and those asked by the client; findings show the information specialist dominates the…

  2. The Reference Encounter Model.

    ERIC Educational Resources Information Center

    White, Marilyn Domas

    1983-01-01

    Develops model of the reference interview which explicitly incorporates human information processing, particularly schema ideas presented by Marvin Minsky and other theorists in cognitive processing and artificial intelligence. Questions are raised concerning use of content analysis of transcribed verbal protocols as methodology for studying…

  3. Reference-Dependent Sympathy

    ERIC Educational Resources Information Center

    Small, Deborah A.

    2010-01-01

    Natural disasters and other traumatic events often draw a greater charitable response than do ongoing misfortunes, even those that may cause even more widespread misery, such as famine or malaria. Why is the response disproportionate to need? The notion of reference dependence critical to Prospect Theory (Kahneman & Tversky, 1979) maintains that…

  4. Virtual Reference Services.

    ERIC Educational Resources Information Center

    Brewer, Sally

    2003-01-01

    As the need to access information increases, school librarians must create virtual libraries. Linked to reliable reference resources, the virtual library extends the physical collection and library hours and lets students learn to use Web-based resources in a protected learning environment. The growing number of virtual schools increases the need…

  5. Reference Collections and Standards.

    ERIC Educational Resources Information Center

    Winkel, Lois

    1999-01-01

    Reviews six reference materials for young people: "The New York Public Library Kid's Guide to Research"; "National Audubon Society First Field Guide. Mammals"; "Star Wars: The Visual Dictionary"; "Encarta Africana"; "World Fact Book, 1998"; and "Factastic Book of 1001 Lists". Includes ordering information.(AEF)

  6. A GUJARATI REFERENCE GRAMMAR.

    ERIC Educational Resources Information Center

    CARDONA, GEORGE

    THIS REFERENCE GRAMMAR WAS WRITTEN TO FILL THE NEED FOR AN UP-TO-DATE ANALYSIS OF THE MODERN LANGUAGE SUITABLE FOR LANGUAGE LEARNERS AS WELL AS LINGUISTS. THE AUTHOR LISTS IN THE INTRODUCTION THOSE STUDIES PREVIOUS TO THIS ONE WHICH MAY BE OF INTEREST TO THE READER. INCLUDED IN HIS ANALYSIS OF THE LANGUAGE ARE MAJOR CHAPTERS ON--(1) PHONOLOGY, (2)…

  7. Reference Sources for Nursing

    ERIC Educational Resources Information Center

    Nursing Outlook, 1976

    1976-01-01

    The ninth revision (including a Canadian supplement) of a list of nursing reference works lists items in the following sections: abstract journals, audiovisuals, bibliographies, dictionaries, directories, drug lists and pharmacologies, educational programs, histories, indexes, legal guides, library administration and organization, research grants,…

  8. Reference Sources for Nursing

    ERIC Educational Resources Information Center

    Nursing Outlook, 1978

    1978-01-01

    The tenth revision of a list of reference works for nurses, revised by a committee of the Interagency Council on Library Resources for Nursing, listed by type of publication as abstract journals, audiovisuals, bibliographies, books, dictionaries, directories, pharmacologies, indexes, guides, and so on. (MF)

  9. Selecting a Reference Object

    ERIC Educational Resources Information Center

    Miller, Jared E.; Carlson, Laura A.; Hill, Patrick L.

    2011-01-01

    One way to describe the location of an object is to relate it to another object. Often there are many nearby objects, each of which could serve as a candidate to be the reference object. A common theoretical assumption is that features that make a given object salient relative to the candidate set are instrumental in determining which is selected.…

  10. Isotope reference materials

    USGS Publications Warehouse

    Coplen, Tyler B.

    2010-01-01

    Measurement of the same isotopically homogeneous sample by any laboratory worldwide should yield the same isotopic composition within analytical uncertainty. International distribution of light element isotopic reference materials by the International Atomic Energy Agency and the U.S. National Institute of Standards and Technology enable laboratories to achieve this goal.

  11. Reference Model Development

    SciTech Connect

    Jepsen, Richard

    2011-11-02

    Presentation from the 2011 Water Peer Review in which principal investigator discusses project progress to develop a representative set of Reference Models (RM) for the MHK industry to develop baseline cost of energy (COE) and evaluate key cost component/system reduction pathways.

  12. Hospitality Services Reference Book.

    ERIC Educational Resources Information Center

    Texas Tech Univ., Lubbock. Home Economics Curriculum Center.

    This reference book provides information needed by employees in hospitality services occupations. It includes 29 chapters that cover the following topics: the hospitality services industry; professional ethics; organization and management structures; safety practices and emergency procedures; technology; property maintenance and repair; purchasing…

  13. An Amharic Reference Grammar.

    ERIC Educational Resources Information Center

    Leslau, Wolf

    This reference grammar presents a structural description of the orthography, phonology, morphology, and syntax of Amharic, the national language of Ethiopia. The Amharic material in this work, designed to prepare the student for speaking and reading the language, appears in both Amharic script and phonetic transcription. See ED 012 044-5 for the…

  14. The Unreliability of References

    ERIC Educational Resources Information Center

    Barden, Dennis M.

    2008-01-01

    When search consultants, like the author, are invited to propose their services in support of a college or university seeking new leadership, they are generally asked a fairly standard set of questions. But there is one question that they find among the most difficult to answer: How do they check a candidate's references to ensure that they know…

  15. Generating Multimodal References

    ERIC Educational Resources Information Center

    van der Sluis, Ielka; Krahmer, Emiel

    2007-01-01

    This article presents a new computational model for the generation of multimodal referring expressions (REs), based on observations in human communication. The algorithm is an extension of the graph-based algorithm proposed by Krahmer, van Erk, and Verleg (2003) and makes use of a so-called Flashlight Model for pointing. The Flashlight Model…

  16. International reference ionosphere 1990

    NASA Technical Reports Server (NTRS)

    Bilitza, Dieter; Rawer, K.; Bossy, L.; Kutiev, I.; Oyama, K.-I.; Leitinger, R.; Kazimirovsky, E.

    1990-01-01

    The International Reference Ionosphere 1990 (IRI-90) is described. IRI described monthly averages of the electron density, electron temperature, ion temperature, and ion composition in the altitude range from 50 to 1000 km for magnetically quiet conditions in the non-auroral ionosphere. The most important improvements and new developments are summarized.

  17. OSH technical reference manual

    SciTech Connect

    Not Available

    1993-11-01

    In an evaluation of the Department of Energy (DOE) Occupational Safety and Health programs for government-owned contractor-operated (GOCO) activities, the Department of Labor`s Occupational Safety and Health Administration (OSHA) recommended a technical information exchange program. The intent was to share written safety and health programs, plans, training manuals, and materials within the entire DOE community. The OSH Technical Reference (OTR) helps support the secretary`s response to the OSHA finding by providing a one-stop resource and referral for technical information that relates to safe operations and practice. It also serves as a technical information exchange tool to reference DOE-wide materials pertinent to specific safety topics and, with some modification, as a training aid. The OTR bridges the gap between general safety documents and very specific requirements documents. It is tailored to the DOE community and incorporates DOE field experience.

  18. Open SHMEM Reference Implementation

    SciTech Connect

    Pritchard, Howard; Curtis, Anthony; Welch, Aaron; Fridley, Andrew

    2016-05-12

    OpenSHMEM is an effort to create a specification for a standardized API for parallel programming in the Partitioned Global Address Space. Along with the specification the project is also creating a reference implementation of the API. This implementation attempts to be portable, to allow it to be deployed in multiple environments, and to be a starting point for implementations targeted to particular hardware platforms. It will also serve as a springboard for future development of the API.

  19. Range Reference Notebook

    DTIC Science & Technology

    2006-10-15

    rifle grenade (inert), tin can lid, 15” tent peg 3 Table FRD-7. Fort Ritchie Sector 3 Representative Examples of Non-MEC Clutter Description 1/2...Appendix B—Indirect Fire Range Examples SITES ( ADI ) Adak Naval Air Facility, AK, Mitt Lake Mortar Range (FRI) Fort Ritchie...example range. B- ADI -1 Indirect-Fire Range,: Adak, AK, Mitt Lake Mortar Range Impact Area Site-Specific References – Adak NAF Foster Wheeler

  20. Precision optical reference frequencies

    NASA Astrophysics Data System (ADS)

    Riehle, Fritz; Schnatz, Harald; Zinner, G.; Trebst, Tilmann; Helmcke, Juergen

    1999-05-01

    Optical reference frequencies are provided by lasers of which the frequencies are stabilized to suitable absorption lines. Presently, twelve reference frequencies/wavelengths within the wavelengths range from 243 nm to 10.3 micrometers are recommended by the International Committee of Weights and Measures as references for the realization of the meter and scientific applications. As typical examples, we describe a diode-pumped, frequency doubled YAG-laser stabilized to an absorption line of molecular iodine and a Ca-stabilized laser. The latter one has been developed in two versions, a transportable system utilizing a small beam of thermal Ca atoms and a stationary standard based on laser cooled and trapped Ca atoms. The frequency of the Ca standard based on cold Ca atoms has been measured by a frequency chain allowing a phase-coherent comparison against the primary standard of time and frequency, the caesium clock. Its value is vCa equals 455 986 240 494.13 kHz with a relative standard uncertainty of 2.5 (DOT) 10-13.

  1. Celestial Reference Frames

    NASA Astrophysics Data System (ADS)

    Jacobs, Christopher S.

    2013-03-01

    Concepts and Background: This paper gives an overview of modern celestial reference frames as realized at radio frequencies using the Very Long baseline Interferometry (VLBI) technique. We discuss basic celestial reference frame concepts, desired properties, and uses. We review the networks of antennas used for this work. We briefly discuss the history of the science of astrometry touching upon the discovery of precession, proper motion, nutation, and parallax, and the field of radio astronomy. Building Celestial Frames: Next, we discuss the multi-step process of building a celestial frame: First candidate sources are identified based on point-like properties from single dish radio telescopes surveys. Second, positions are refined using connected element interferometers such as the Very Large Array, and the ATCA. Third, positions of approximately milli-arcsecond (mas) accuracy are determined using intercontinental VLBI surveys. Fourth, sub-mas positions are determined by multiyear programs using intercontinental VLBI. These sub-mas sets of positions are then verified by multiple teams in preparation for release to non-specialists in the form of an official IAU International Celestial Reference Frame (ICRF). The process described above has until recently been largely restricted to work at S/X-band (2.3/8.4 GHz). However, in the last decade sub-mas work has expanded to include celestial frames at K-band (24 GHz), Ka-band (32 GHz), and Q-band (43 GHz). While these frames currently have the disadvantage of far smaller data sets, the astrophysical quality of the sources themselves improves at these higher frequencies and thus make these frequencies attractive for realizations of celestial reference frames. Accordingly, we review progress at these higher frequency bands. Path to the Future: We discuss prospects for celestial reference frames over the next decade. We present an example of an error budget for astrometric VLBI and discuss the budget's use as a tool for

  2. Celestial Reference Frame

    NASA Astrophysics Data System (ADS)

    Jacobs, Christopher S.

    2013-09-01

    Concepts and Background: This paper gives an overview of modern celestial reference frames as realized at radio frequencies using the Very Long baseline Interferometry (VLBI) technique. We discuss basic celestial reference frame concepts, desired properties, and uses. We review the networks of antennas used for this work. We briefly discuss the history of the science of astrometry touching upon the discovery of precession, proper motion, nutation, and parallax, and the field of radio astronomy. Building Celestial Frames: Next, we discuss the multi-step process of building a celestial frame: First candidate sources are identified based on point-like properties from single dish radio telescopes surveys. Second, positions are refined using connected element interferometers such as the Very Large Array, and the ATCA. Third, positions of approximately milli-arcsecond (mas) accuracy are determined using intercontinental VLBI surveys. Fourth, sub-mas positions are determined by multiyear programs using intercontinental VLBI. These sub-mas sets of positions are then verified by multiple teams in preparation for release to non-specialists in the form of an official IAU International Celestial Reference Frame (ICRF). The process described above has until recently been largely restricted to work at S/X-band (2.3/8.4 GHz). However, in the last decade sub-mas work has expanded to include celestial frames at K-band (24 GHz), Ka-band (32 GHz), and Q-band (43 GHz). While these frames currently have the disadvantage of far smaller data sets, the astrophysical quality of the sources themselves improves at these higher frequencies and thus make these frequencies attractive for realizations of celestial reference frames. Accordingly, we review progress at these higher frequency bands. Path to the Future: We discuss prospects for celestial reference frames over the next decade. We present an example of an error budget for astrometric VLBI and discuss the budget's use as a tool for

  3. Terminal Forecast Reference Notebook.

    DTIC Science & Technology

    1979-11-07

    Figure 18 , Surface Map 1230Z, October 24, 1948). 4I 7Cm 19 (2) During late spring, suuer or early autumn high oells some- times move southward into the...TFRF, is an excellent reference for this subject. 0 06 0070 I.N ATC 1. A- 2 AREAI p/ A-2 AREA I 1. General: Most flights briefed by Det 18 are within or...in close proxi- mity to Area I. For this reason, Det 18 personnel must become extremely knowledgeable of Area I. 2. Location and Background: The ROK

  4. Commercial scale research and assessment of poultry welfare.

    PubMed

    Dawkins, Marian Stamp

    2012-01-01

    1. Commercial level research on poultry welfare is increasingly important because of the insight it gives into what improves welfare in the context of other important drivers such as human health, environmental impact and cost. 2. There are, however, a number of problems with conducting commercial level research - such as conflicts over aims, financial compensation and legal issues - that need to be addressed if the gains from commercial research are to be optimized. Cooperation between all parties and mutual understanding of the different priorities that may exist between industry and academia are essential. 3. Three important developments for the future are: the setting up of a 'data bank', the application of new statistical methods for analyzing data and new technology for assessing welfare automatically.

  5. Feasibility of Producing Reconstituted Railroad Ties on a Commercial Scale.

    DTIC Science & Technology

    1982-09-01

    FRA), the Forest Products Laboratory, and the Potlatch Corporation was undertaken to determine the feasibility of manufacturing ties in a pilot...by the Potlatch Corporation. A cooperative of the total volume of the tlejk . -T. Face and core research effort, limited In scope to the fabrication...o4 11 materials were obtained by separating 0.040-inch-thick ties, was arranged between FPL and Potlatch to deter- by random width by 2-inch-long ring

  6. Coal data: A reference

    SciTech Connect

    Not Available

    1995-02-01

    This report, Coal Data: A Reference, summarizes basic information on the mining and use of coal, an important source of energy in the US. This report is written for a general audience. The goal is to cover basic material and strike a reasonable compromise between overly generalized statements and detailed analyses. The section ``Supplemental Figures and Tables`` contains statistics, graphs, maps, and other illustrations that show trends, patterns, geographic locations, and similar coal-related information. The section ``Coal Terminology and Related Information`` provides additional information about terms mentioned in the text and introduces some new terms. The last edition of Coal Data: A Reference was published in 1991. The present edition contains updated data as well as expanded reviews and additional information. Added to the text are discussions of coal quality, coal prices, unions, and strikes. The appendix has been expanded to provide statistics on a variety of additional topics, such as: trends in coal production and royalties from Federal and Indian coal leases, hours worked and earnings for coal mine employment, railroad coal shipments and revenues, waterborne coal traffic, coal export loading terminals, utility coal combustion byproducts, and trace elements in coal. The information in this report has been gleaned mainly from the sources in the bibliography. The reader interested in going beyond the scope of this report should consult these sources. The statistics are largely from reports published by the Energy Information Administration.

  7. Molecular biology references.

    PubMed

    2003-05-01

    Many of the units in this manual describe methods and techniques for the cloning, expression, and structural analysis of neural genes and proteins. We assume that users of these protocols have at least some introductory background in recombinant DNA technology (or are working with a collaborator who does); therefore, we have not provided comprehensive coverage of all of these topics, but rather have concentrated on presenting selected techniques that will be of the most interest and use to the general neuroscience laboratory. More comprehensive coverage of these topics can be found in Current Protocols in Molecular Biology (CPMB), which is extensively cross-referenced throughout this manual. These cross-references are summarized in this appendix.

  8. Bulk Site Reference Materials

    SciTech Connect

    Barich, J.J. III; Jones, R.R. Sr.

    1996-12-31

    The selection, manufacture and use of Bulk Site Reference Materials (BSRMs) at hazardous waste sites is discussed. BSRMs are useful in preparing stabilization/solidification (S/S) formulations for soils, ranking competing S/S processes, comparing S/S alternatives to other technologies, and in interpreting data from different test types. BSRMs are large volume samples that are representative of the physical and chemical characteristics of a site soil, and that contain contaminants at reasonably high levels. A successful BSRM is extremely homogeneous and well-characterized. While not representative of any point on the site, they contain the contaminants of the site in the matrices of the site. Design objectives for a BSRM are to produce a material that (1) maintains good fidelity to site matrices and contaminants, and (2) exhibits the lowest possible relative standard deviation.

  9. PASCAL/48 reference manual

    NASA Technical Reports Server (NTRS)

    Knight, J. C.; Hamm, R. W.

    1984-01-01

    PASCAL/48 is a programming language for the Intel MCS-48 series of microcomputers. In particular, it can be used with the Intel 8748. It is designed to allow the programmer to control most of the instructions being generated and the allocation of storage. The language can be used instead of ASSEMBLY language in most applications while allowing the user the necessary degree of control over hardware resources. Although it is called PASCAL/48, the language differs in many ways from PASCAL. The program structure and statements of the two languages are similar, but the expression mechanism and data types are different. The PASCAL/48 cross-compiler is written in PASCAL and runs on the CDC CYBER NOS system. It generates object code in Intel hexadecimal format that can be used to program the MCS-48 series of microcomputers. This reference manual defines the language, describes the predeclared procedures, lists error messages, illustrates use, and includes language syntax diagrams.

  10. Long life reference electrode

    DOEpatents

    Yonco, R.M.; Nagy, Z.

    1987-07-30

    An external, reference electrode is provided for long term use with a high temperature, high pressure system. The electrode is arranged in a vertical, electrically insulative tube with an upper portion serving as an electrolyte reservoir and a lower portion in electrolytic communication with the system to be monitored. The lower end portion includes a flow restriction such as a porous plug to limit the electrolyte release into the system. A piston equalized to the system pressure is fitted into the upper portion of the tube to impart a small incremental pressure to the electrolyte. The piston is selected of suitable size and weight to cause only a slight flow of electrolyte through the porous plug into the high pressure system. This prevents contamination of the electrolyte but is of such small flow rate that operating intervals of a month or more can be achieved. 2 figs.

  11. Long life reference electrode

    DOEpatents

    Yonco, R.M.; Nagy, Z.

    1989-04-04

    An external, reference electrode is provided for long term use with a high temperature, high pressure system. The electrode is arranged in a vertical, electrically insulative tube with an upper portion serving as an electrolyte reservoir and a lower portion in electrolytic communication with the system to be monitored. The lower end portion includes a flow restriction such as a porous plug to limit the electrolyte release into the system. A piston equalized to the system pressure is fitted into the upper portion of the tube to impart a small incremental pressure to the electrolyte. The piston is selected of suitable size and weight to cause only a slight flow of electrolyte through the porous plug into the high pressure system. This prevents contamination of the electrolyte but is of such small flow rate that operating intervals of a month or more can be achieved. 2 figs.

  12. Long life reference electrode

    DOEpatents

    Yonco, Robert M.; Nagy, Zoltan

    1989-01-01

    An external, reference electrode is provided for long term use with a high temperature, high pressure system. The electrode is arranged in a vertical, electrically insulative tube with an upper portion serving as an electrolyte reservior and a lower portion in electrolytic communication with the system to be monitored. The lower end portion includes a flow restriction such as a porous plug to limit the electrolyte release into the system. A piston equalized to the system pressure is fitted into the upper portion of the tube to impart a small incremental pressure to the electrolyte. The piston is selected of suitable size and weight to cause only a slight flow of electrolyte through the porous plug into the high pressure system. This prevents contamination of the electrolyte but is of such small flow rate that operating intervals of a month or more can be achieved.

  13. Tank characterization reference guide

    SciTech Connect

    De Lorenzo, D.S.; DiCenso, A.T.; Hiller, D.B.; Johnson, K.W.; Rutherford, J.H.; Smith, D.J.; Simpson, B.C.

    1994-09-01

    Characterization of the Hanford Site high-level waste storage tanks supports safety issue resolution; operations and maintenance requirements; and retrieval, pretreatment, vitrification, and disposal technology development. Technical, historical, and programmatic information about the waste tanks is often scattered among many sources, if it is documented at all. This Tank Characterization Reference Guide, therefore, serves as a common location for much of the generic tank information that is otherwise contained in many documents. The report is intended to be an introduction to the issues and history surrounding the generation, storage, and management of the liquid process wastes, and a presentation of the sampling, analysis, and modeling activities that support the current waste characterization. This report should provide a basis upon which those unfamiliar with the Hanford Site tank farms can start their research.

  14. On establishing reference values.

    PubMed Central

    Lumsden, J H; Mullen, K

    1978-01-01

    In order to establish a range of reference values for any characteristic one can use Gaussian or nonparametric techniques, whichever are most appropriate. One has the choice of calculating tolerance intervals or percentile intervals. A tolerance interval is said to contain, say 95% of the population with probability, say 0.90. A percentile interval simply simply calculates the values between which 95% of the observations fall. If the data can be said to have a Gaussian distribution, the same precision can be obtained with smaller sample sizes than using the nonparametric techniques. In some cases, data which are not Gaussian can be transformed into a Gaussian form and hence make use of the more efficient Gaussian techniques. In both cases, the data should be checked for outliers or rogue observations and these should be eliminated if the testing procedure fails to imply that they are an integral part of the data. PMID:688072

  15. Nuclear Science References Database

    SciTech Connect

    Pritychenko, B.; Běták, E.; Singh, B.; Totans, J.

    2014-06-15

    The Nuclear Science References (NSR) database together with its associated Web interface, is the world's only comprehensive source of easily accessible low- and intermediate-energy nuclear physics bibliographic information for more than 210,000 articles since the beginning of nuclear science. The weekly-updated NSR database provides essential support for nuclear data evaluation, compilation and research activities. The principles of the database and Web application development and maintenance are described. Examples of nuclear structure, reaction and decay applications are specifically included. The complete NSR database is freely available at the websites of the National Nuclear Data Center (http://www.nndc.bnl.gov/nsr) and the International Atomic Energy Agency (http://www-nds.iaea.org/nsr)

  16. International Reference Ionosphere -2010

    NASA Astrophysics Data System (ADS)

    Bilitza, Dieter; Reinisch, Bodo

    The International Reference Ionosphere 2010 includes several important improvements and ad-ditions. This presentation introduces these changes and discusses their benefits. The electron and ion density profiles for the bottomside ionosphere will be significantly improved by using more ionosonde data as well as photochemical considerations. As an additional lower iono-sphere parameter IRI-2010 will include the transition height from molecular to cluster ions. At the F2 peak Neural Net models for the peak density and the propagation factor M3000F2, which is related to the F2 peak height, are introduced as new options. At high latitudes the model will benefit from the introduction of auroral oval boundaries and their variation with magnetic activity. Regarding the electron temperature, IRI-2010 now models variations with solar activity. The homepage for the IRI project is at http://IRI.gsfc.nasa.gov/.

  17. Innovative clean coal technology (ICCT): demonstration of selective catalytic reduction (SCR) technology for the control of nitrogen oxide (NO{sub x}) emission from high-sulfur, coal-fired boilers - economic evaluation of commercial-scale SCR applications for utility boilers

    SciTech Connect

    Healy, E.C.; Maxwell, J.D.; Hinton, W.S.

    1996-09-01

    This report presents the results of an economic evaluation produced as part of the Innovative Clean Coal Technology project, which demonstrated selective catalytic reduction (SCR) technology for reduction of NO{sub x} emissions from utility boilers burning U.S. high-sulfur coal. The document includes a commercial-scale capital and O&M cost evaluation of SCR technology applied to a new facility, coal-fired boiler utilizing high-sulfur U.S. coal. The base case presented herein determines the total capital requirement, fixed and variable operating costs, and levelized costs for a new 250-MW pulverized coal utility boiler operating with a 60-percent NO{sub x} removal. Sensitivity evaluations are included to demonstrate the variation in cost due to changes in process variables and assumptions. This report also presents the results of a study completed by SCS to determine the cost and technical feasibility of retrofitting SCR technology to selected coal-fired generating units within the Southern electric system.

  18. Preliminary reference Earth model

    NASA Astrophysics Data System (ADS)

    Dziewonski, Adam M.; Anderson, Don L.

    1981-06-01

    A large data set consisting of about 1000 normal mode periods, 500 summary travel time observations, 100 normal mode Q values, mass and moment of inertia have been inverted to obtain the radial distribution of elastic properties, Q values and density in the Earth's interior. The data set was supplemented with a special study of 12 years of ISC phase data which yielded an additional 1.75 × 10 6 travel time observations for P and S waves. In order to obtain satisfactory agreement with the entire data set we were required to take into account anelastic dispersion. The introduction of transverse isotropy into the outer 220 km of the mantle was required in order to satisfy the shorter period fundamental toroidal and spheroidal modes. This anisotropy also improved the fit of the larger data set. The horizontal and vertical velocities in the upper mantle differ by 2-4%, both for P and S waves. The mantle below 220 km is not required to be anisotropic. Mantle Rayleigh waves are surprisingly sensitive to compressional velocity in the upper mantle. High S n velocities, low P n velocities and a pronounced low-velocity zone are features of most global inversion models that are suppressed when anisotropy is allowed for in the inversion. The Preliminary Reference Earth Model, PREM, and auxiliary tables showing fits to the data are presented.

  19. Reference change values.

    PubMed

    Fraser, Callum G

    2011-09-30

    Reference change values (RCV) provide objective tools for assessment of the significance of differences in serial results from an individual. The concept is simple and the calculation easy, since all laboratories know their analytical imprecision (CV(A)) and estimates of within-subject biological variation (CV(I)) are available for a large number of quantities. Generally, CV(I) are constant over time, geography, methodology and in health and chronic stable disease. The formula is RCV=2(1/2) · Z · (CV(A)(2) + CV(I)(2))(1/2), where Z is the number of standard deviations appropriate to the probability. Correct interpretation of the semantics describing the clinical use of RCV is vital for selection of the Z-score. Many quantities of clinically importance exist for which good estimates of RCV are unavailable. Derivation of CV(I) may be difficult for such quantities: flair and imagination are required in selecting populations with chronic but stable disease on whom CV(I) can be determined. RCV can be used for delta-checking and auto-verification and laboratory information management systems (LIMS) can be adapted to do this. Recently, log-normal transformation to obtain unidirectional RCV has been used. Gaps in knowledge of RCV still require filling since the need for measures of change is clearly expressed in guidelines.

  20. Sensor Characteristics Reference Guide

    SciTech Connect

    Cree, Johnathan V.; Dansu, A.; Fuhr, P.; Lanzisera, Steven M.; McIntyre, T.; Muehleisen, Ralph T.; Starke, M.; Banerjee, Pranab; Kuruganti, T.; Castello, C.

    2013-04-01

    The Buildings Technologies Office (BTO), within the U.S. Department of Energy (DOE), Office of Energy Efficiency and Renewable Energy (EERE), is initiating a new program in Sensor and Controls. The vision of this program is: • Buildings operating automatically and continuously at peak energy efficiency over their lifetimes and interoperating effectively with the electric power grid. • Buildings that are self-configuring, self-commissioning, self-learning, self-diagnosing, self-healing, and self-transacting to enable continuous peak performance. • Lower overall building operating costs and higher asset valuation. The overarching goal is to capture 30% energy savings by enhanced management of energy consuming assets and systems through development of cost-effective sensors and controls. One step in achieving this vision is the publication of this Sensor Characteristics Reference Guide. The purpose of the guide is to inform building owners and operators of the current status, capabilities, and limitations of sensor technologies. It is hoped that this guide will aid in the design and procurement process and result in successful implementation of building sensor and control systems. DOE will also use this guide to identify research priorities, develop future specifications for potential market adoption, and provide market clarity through unbiased information

  1. World Reference Center for Arboviruses.

    DTIC Science & Technology

    1977-08-01

    multiple sclerosis . Lyme disease was associated in distribution with Ixodes ticks but the etiologic agent was not isolated. The reference center distributed 566 ampoules of reference sera, viruses, and antigens during 1977; mosquito and vertebrate cell lines were also distributed.

  2. Knowledge Management and Reference Services

    ERIC Educational Resources Information Center

    Gandhi, Smiti

    2004-01-01

    Many corporations are embracing knowledge management (KM) to capture the intellectual capital of their employees. This article focuses on KM applications for reference work in libraries. It defines key concepts of KM, establishes a need for KM for reference services, and reviews various KM initiatives for reference services.

  3. Web Reference: A Virtual Reality.

    ERIC Educational Resources Information Center

    Foster, Janet

    1999-01-01

    Presents ideas and strategies to enhance digital reference services available via the Internet in public libraries. Describes print publications which include Web reference columns; subject guides, both print and online; and the resources of the Internet Public Library and other virtual reference desks. (LRW)

  4. Paraprofessionals at the Reference Desk.

    ERIC Educational Resources Information Center

    Murfin, Marjorie E.; Bunge, Charles A.

    1988-01-01

    Describes a study that compared the quality of reference services provided by reference librarians and paraprofessionals, using patron satisfaction as the measure of success. Factors associated with satisfactory service are identified, and suggestions for the effective use of paraprofessional staff are presented. (4 references) (CLB)

  5. Fundamentals of Managing Reference Collections

    ERIC Educational Resources Information Center

    Singer, Carol A.

    2012-01-01

    Whether a library's reference collection is large or small, it needs constant attention. Singer's book offers information and insight on best practices for reference collection management, no matter the size, and shows why managing without a plan is a recipe for clutter and confusion. In this very practical guide, reference librarians will learn:…

  6. Canadian listeriosis reference service.

    PubMed

    Pagotto, Franco; Ng, Lai-King; Clark, Clifford; Farber, Jeff

    2006-01-01

    Listeria monocytogenes, a psychrotrophic organism capable of growing at refrigeration temperatures, is of major concern in extended shelf life, refrigerated foods. Considering that as much as 80-90% of human listeriosis cases are linked to the ingestion of contaminated food, human cases are predominantly seen in high-risk individuals, including organ-transplant recipients, patients with AIDS and HIV-infected individuals, pregnant women, cancer patients, and the elderly. In 2001, the Canadian Listeriosis Reference Service (LRS) was created by the Bureau of Microbial Hazards (Health Canada) and the National Microbiology Laboratory (now part of the Public Health Agency of Canada). Major goals of the LRS include investigation of listeriosis cases and maintenance of a national collection of isolates. The LRS intends to create a comprehensive molecular epidemiological database of all isolates in Canada for use as a resource for outbreak investigations, research and other microbiological investigations. The PFGE profiles are being established and stored for clinical, food, environmental, and possibly animal strains of L. monocytogenes. The LRS pursues research activities for investigation and implementation of other molecular methods for characterizing L. monocytogenes isolates. Ribotyping, Multi-locus Sequence Typing (MLST), Variable Number of Tandem Repeats (VNTR), Multi-locus virulence sequence typing (MLVA), microarray- based technologies and sequence-based typing schemes, are being investigated on selected diversity sets. The LRS has also used PFGE typing for outbreak investigations. The molecular epidemiological data, timely coordination and exchange of information should help to reduce the incidence of listeriosis in Canada. In Canada, listeriosis is not a national notifiable disease, except for the province of Quebec, where it has been since 1999. The LRS, Canadian Public Health Laboratory Network, and federal epidemiologists are currently working on making human

  7. Capillary reference half-cell

    DOEpatents

    Hall, Stephen H.

    1996-01-01

    The present invention is a reference half-cell electrode wherein intermingling of test fluid with reference fluid does not affect the performance of the reference half-cell over a long time. This intermingling reference half-cell may be used as a single or double junction submersible or surface reference electrode. The intermingling reference half-cell relies on a capillary tube having a first end open to reference fluid and a second end open to test fluid wherein the small diameter of the capillary tube limits free motion of fluid within the capillary to diffusion. The electrode is placed near the first end of the capillary in contact with the reference fluid. The method of operation of the present invention begins with filling the capillary tube with a reference solution. After closing the first end of the capillary, the capillary tube may be fully submerged or partially submerged with the second open end inserted into test fluid. Since the electrode is placed near the first end of the capillary, and since the test fluid may intermingle with the reference fluid through the second open end only by diffusion, this intermingling capillary reference half-cell provides a stable voltage potential for long time periods.

  8. Capillary reference half-cell

    DOEpatents

    Hall, S.H.

    1996-02-13

    The present invention is a reference half-cell electrode wherein intermingling of test fluid with reference fluid does not affect the performance of the reference half-cell over a long time. This intermingling reference half-cell may be used as a single or double junction submersible or surface reference electrode. The intermingling reference half-cell relies on a capillary tube having a first end open to reference fluid and a second end open to test fluid wherein the small diameter of the capillary tube limits free motion of fluid within the capillary to diffusion. The electrode is placed near the first end of the capillary in contact with the reference fluid. The method of operation of the present invention begins with filling the capillary tube with a reference solution. After closing the first end of the capillary, the capillary tube may be fully submerged or partially submerged with the second open end inserted into test fluid. Since the electrode is placed near the first end of the capillary, and since the test fluid may intermingle with the reference fluid through the second open end only by diffusion, this intermingling capillary reference half-cell provides a stable voltage potential for long time periods. 11 figs.

  9. Optical probe with reference fiber

    DOEpatents

    Da Silva, Luiz B.; Chase, Charles L.

    2006-03-14

    A system for characterizing tissue includes the steps of generating an emission signal, generating a reference signal, directing the emission signal to and from the tissue, directing the reference signal in a predetermined manner relative to the emission signal, and using the reference signal to compensate the emission signal. In one embodiment compensation is provided for fluctuations in light delivery to the tip of the probe due to cable motion.

  10. User Preferences in Reference Services: Virtual Reference and Academic Libraries

    ERIC Educational Resources Information Center

    Cummings, Joel; Cummings, Lara; Frederiksen, Linda

    2007-01-01

    This study examines the use of chat in an academic library's user population and where virtual reference services might fit within the spectrum of public services offered by academic libraries. Using questionnaires, this research demonstrates that many within the academic community are open to the idea of chat-based reference or using chat for…

  11. Reach for Reference: Elementary-Middle School Science Reference Collections

    ERIC Educational Resources Information Center

    Safford, Barbara Ripp

    2005-01-01

    This article presents a brief review of some new school science reference works. Two of the sources are traditional, while one is considered experimental. The two traditional reference works reviewed are "The American Heritage Children's Science Dictionary" for upper elementary grades, and "The American Heritage Student Science Dictionary" for…

  12. Reference Readiness for AV Questions.

    ERIC Educational Resources Information Center

    Drolet, Leon L., Jr.

    1981-01-01

    Reviews 50 reference tools which librarians can use to answer almost any audiovisual question including queries on trivia, equipment selection, biographical information, and motion picture ratings. (LLS)

  13. Robot at the Reference Desk?

    ERIC Educational Resources Information Center

    Smith, Karen F.

    1986-01-01

    Describes how a librarian, assisted by a knowledge engineer, developed a computerized reference assistance system for a separate government documents department. Rationale for the expert system, problems in selecting reference materials and user questions to computerize, and the formulation of a workable human/computer interface are covered. A…

  14. Dedicated online virtual reference instruction.

    PubMed

    Guillot, Ladonna; Stahr, Beth; Plaisance, Louise

    2005-01-01

    To facilitate nursing students' information literacy skills and enhance traditional library user services, academic librarians have developed synchronous (real-time) online virtual reference instruction in nursing research classes. The authors discuss collaborative efforts of nursing and library faculty in planning, implementing, and evaluating a discipline-specific virtual reference pilot program.

  15. Moving Reference to the Web.

    ERIC Educational Resources Information Center

    McGlamery, Susan; Coffman, Steve

    2000-01-01

    Explores the possibility of using Web contact center software to offer reference assistance to remote users. Discusses a project by the Metropolitan Cooperative Library System/Santiago Library System consortium to test contact center software and to develop a virtual reference network. (Author/LRW)

  16. The Virtual Reference Librarian's Handbook.

    ERIC Educational Resources Information Center

    Lipow, Anne Grodzins

    This book is a practical guide to librarians and their administrators who are thinking about or in the early stages of providing virtual reference service. Part 1, "The Decision to Go Virtual," provides a context for thinking about virtual reference, including the benefits and problems, getting in the virtual frame of mind, and shopping…

  17. Ethics and the Reference Librarian.

    ERIC Educational Resources Information Center

    Bunge, Charles A.

    1999-01-01

    Discussion of ethical reference practice focuses on guidelines for the individual reference librarian's interactions with clients. Topics include the professional-client relationship; competence; diligence; confidentiality; independence of judgment; honesty and candor; and obligations to third parties, including the democratic society at large.…

  18. Reference for radiographic film interpreters

    NASA Technical Reports Server (NTRS)

    Austin, D. L.

    1970-01-01

    Reference of X-ray film images provides examples of weld defects, film quality, stainless steel welded tubing, and acceptable weld conditions. A summary sheet details the discrepancies shown on the film strip. This reference aids in interpreting and evaluating radiographic film of weldments.

  19. Expert Systems for Reference Work.

    ERIC Educational Resources Information Center

    Parrot, James R.

    1986-01-01

    Discussion of library reference work that may be suitable for use of expert systems focuses on (1) information and literature searches, and (2) requests to interpret bibliographic references and locate items listed. Systems and computer-assisted instruction modules designed for information retrieval at the University of Waterloo Library are…

  20. Technostress and the Reference Librarian.

    ERIC Educational Resources Information Center

    Kupersmith, John

    1992-01-01

    Defines "technostress" as the stress experienced by reference librarians who must constantly deal with the demands of new information technology and the changes they produce in the work place. Discussion includes suggested ways in which both organizations and individuals can work to reduce stress. (27 references) (LAE)

  1. Changing Roles for References Librarians.

    ERIC Educational Resources Information Center

    Kelly, Julia; Robbins, Kathryn

    1996-01-01

    Discusses the future outlook for reference librarians, with topics including: "Technology as the Source of Change"; "Impact of the Internet"; "Defining the Virtual Library"; "Rethinking Reference"; "Out of the Library and into the Streets"; "Asking Users About Their Needs"; "Standardization and Artificial Intelligence"; "The Financial Future"; and…

  2. Queuing Theory and Reference Transactions.

    ERIC Educational Resources Information Center

    Terbille, Charles

    1995-01-01

    Examines the implications of applying the queuing theory to three different reference situations: (1) random patron arrivals; (2) random durations of transactions; and (3) use of two librarians. Tables and figures represent results from spreadsheet calculations of queues for each reference situation. (JMV)

  3. Generalizing indexical-functional reference

    SciTech Connect

    Schoppers, M.; Shu, R.

    1996-12-31

    The goals of situated agents generally do not specify particular objects: they require only that some suitable object should be chosen and manipulated (e.g. any red block). Situated agents engaged in deictic reference grounding, however, may well track a chosen referent object with such fixity of purpose that an unchosen object may be regarded as an obstacle even though it satisfies the agent`s goals. In earlier work this problem was bridged by hand-coding. This paper lifts the problem to the symbol level, endowing agents with perceptual referent selection actions and performing those actions as required to allow or disallow opportunistic re-selection of referents. Our work preserves the ability of situated agents to find and track specific objects, adds an ability to automatically exploit the opportunities allowed by nonspecific references, and provides a starting point for studying how much opportunistic perception is appropriate.

  4. Improved ultrasonic standard reference blocks

    NASA Technical Reports Server (NTRS)

    Eitzen, D. G.; Sushinsky, G. F.; Chwirut, D. J.; Bechtoldt, C. J.; Ruff, A. W.

    1976-01-01

    A program to improve the quality, reproducibility and reliability of nondestructive testing through the development of improved ASTM-type ultrasonic reference standards is described. Reference blocks of aluminum, steel, and titanium alloys are to be considered. Equipment representing the state-of-the-art in laboratory and field ultrasonic equipment was obtained and evaluated. RF and spectral data on ten sets of ultrasonic reference blocks have been taken as part of a task to quantify the variability in response from nominally identical blocks. Techniques for residual stress, preferred orientation, and micro-structural measurements were refined and are applied to a reference block rejected by the manufacturer during fabrication in order to evaluate the effect of metallurgical condition on block response. New fabrication techniques for reference blocks are discussed and ASTM activities are summarized.

  5. Review of the Reference Dose and Reference Concentration Processes Document

    EPA Pesticide Factsheets

    Summarizes the review and deliberations of the Risk Assessment Forum’s RfD/RfC Technical Panel and its recommendations for improvements in oral referencedose/inhalation reference concentration (RfD/RfC) process.

  6. Reference and Standard Atmosphere Models

    NASA Technical Reports Server (NTRS)

    Johnson, Dale L.; Roberts, Barry C.; Vaughan, William W.; Parker, Nelson C. (Technical Monitor)

    2002-01-01

    This paper describes the development of standard and reference atmosphere models along with the history of their origin and use since the mid 19th century. The first "Standard Atmospheres" were established by international agreement in the 1920's. Later some countries, notably the United States, also developed and published "Standard Atmospheres". The term "Reference Atmospheres" is used to identify atmosphere models for specific geographical locations. Range Reference Atmosphere Models developed first during the 1960's are examples of these descriptions of the atmosphere. This paper discusses the various models, scopes, applications and limitations relative to use in aerospace industry activities.

  7. Genetics Home Reference: isolated hyperchlorhidrosis

    MedlinePlus

    ... loss of salt (sodium chloride or NaCl) in sweat. In particular, "hyperchlorhidrosis" refers to the high levels of chloride found in sweat, although both sodium and chloride are released. Because ...

  8. Sports Reference: A Core Collection.

    ERIC Educational Resources Information Center

    Safford, Barbara Ripp

    2003-01-01

    Discusses reasons for including sports books in school library reference collections, explains why they should not be found only in public library collections, and provides six annotated bibliographies of sports books suitable for intermediate or middle school library collections. (LRW)

  9. Computerizing the Reference Desk Schedule.

    ERIC Educational Resources Information Center

    deHaas, Pat

    1983-01-01

    Discussion of the scheduling procedures of librarians' hours at the reference desk at the Rutherford Humanities and Social Sciences Library, University of Alberta, highlights services provided, the preference table system, and manual scheduling versus computer scheduling. (EJS)

  10. Genetics Home Reference: Laron syndrome

    MedlinePlus

    ... AL. Obesity, diabetes and cancer: insight into the relationship from a cohort with growth hormone receptor deficiency. ... healthcare professional . About Genetics Home Reference Site Map Customer Support Selection Criteria for Links USA.gov Copyright ...

  11. Genetics Home Reference: Miyoshi myopathy

    MedlinePlus

    ... Itoyama Y. Dysferlin mutations in Japanese Miyoshi myopathy: relationship to phenotype. Neurology. 2003 Jun 10;60(11): ... healthcare professional . About Genetics Home Reference Site Map Customer Support Selection Criteria for Links USA.gov Copyright ...

  12. Genetics Home Reference: Asperger syndrome

    MedlinePlus

    ... a combination of genetic variations and environmental factors influence the development of this complex condition. Asperger syndrome ... healthcare professional . About Genetics Home Reference Site Map Customer Support Selection Criteria for Links USA.gov Copyright ...

  13. Selected Reference Books of 1999.

    ERIC Educational Resources Information Center

    McIlvaine, Eileen

    2000-01-01

    Presents annotated bibliographies of a selection of recent scholarly and general reference works under the subject headings of publishing, periodical indexes, philosophy and religion, literature, music, art, photography, social sciences, business, history, and new editions. (LRW)

  14. International reference standards in coagulation.

    PubMed

    Raut, Sanj; Hubbard, Anthony R

    2010-07-01

    Measurement of coagulation factor activity using absolute physico-chemical techniques is not possible and estimation therefore relies on comparative bioassay relative to a reference standard with a known or assigned potency. However the inherent variability of locally prepared and calibrated reference standards can give rise to poor agreement between laboratories and methods. Harmonisation of measurement between laboratories at the international level relies on the availability of a common source of calibration for local reference standards and this is provided by the World Health Organization (WHO) International Standards which define the International Unit for the analyte. This article describes the principles, practices and problems of biological standardisation and the development and use of reference standards for assays of coagulation factors, with particular emphasis on WHO International Standards for both concentrates and plasma.

  15. Genetics Home Reference: WAGR syndrome

    MedlinePlus

    ... signs and symptoms of WAGR syndrome can include childhood-onset obesity, inflammation of the pancreas (pancreatitis), and kidney failure. When WAGR syndrome includes childhood-onset obesity, it is often referred to as WAGRO syndrome. ...

  16. Improved ultrasonic standard reference blocks

    NASA Technical Reports Server (NTRS)

    Eitzen, D. G.

    1975-01-01

    A program to improve the quality, reproducibility and reliability of nondestructive testing through the development of improved ASTM-type ultrasonic reference standards is described. Reference blocks of aluminum, steel, and titanium alloys were considered. Equipment representing the state-of-the-art in laboratory and field ultrasonic equipment was obtained and evaluated. Some RF and spectral data on ten sets of ultrasonic reference blocks were taken as part of a task to quantify the variability in response from nominally identical blocks. Techniques for residual stress, preferred orientation, and microstructural measurements were refined and are applied to a reference block rejected by the manufacturer during fabrication in order to evaluate the effect of metallurgical condition on block response.

  17. Virtual reference: chat with us!

    PubMed

    Lapidus, Mariana; Bond, Irena

    2009-01-01

    Virtual chat services represent an exciting way to provide patrons of medical libraries with instant reference help in an academic environment. The purpose of this article is to examine the implementation, marketing process, use, and development of a virtual reference service initiated at the Massachusetts College of Pharmacy and Health Sciences and its three-campus libraries. In addition, this paper will discuss practical recommendations for the future improvement of the service.

  18. Space Station reference configuration description

    NASA Technical Reports Server (NTRS)

    1984-01-01

    The data generated by the Space Station Program Skunk Works over a period of 4 months which supports the definition of a Space Station reference configuration is documented. The data were generated to meet these objectives: (1) provide a focal point for the definition and assessment of program requirements; (2) establish a basis for estimating program cost; and (3) define a reference configuration in sufficient detail to allow its inclusion in the definition phase Request for Proposal (RFP).

  19. Virtual Reference Interferometry: Theory & Experiment

    NASA Astrophysics Data System (ADS)

    Galle, Michael Anthony

    This thesis introduces the idea that a simulated interferogram can be used as a reference for an interferometer. This new concept represents a paradigm shift from the conventional thinking, where a reference is the phase of a wavefront that traverses a known path. The simulated interferogram used as a reference is called a virtual reference. This thesis develops the theory of virtual reference interferometry and uses it for the characterization of chromatic dispersion in short length (<1m) fibers and optical components. Characterization of chromatic dispersion on short length fiber and optical components is a very difficult challenge. Accurate measurement of first and second order dispersion is important for applications from optical component design to nonlinear photonics, sensing and communications. Techniques for short-length dispersion characterization are therefore critical to the development of many photonic systems. The current generation of short-length dispersion measurement techniques are either easy to operate but lack sufficient accuracy, or have sufficient accuracy but are difficult to operate. The use of a virtual reference combines the advantages of these techniques so that it is both accurate and easy to operate. Chromatic dispersion measurements based on virtual reference interferometry have similar accuracy as the best conventional measurement techniques due to the ability to measure first and second order dispersion directly from the interference pattern. Unique capabilities of virtual reference interferometry are demonstrated, followed by a derivation of the operational constraints and system parameters. The technique is also applied to the characterization of few-mode fibers, a hot topic in telecommunications research where mode division multiplexing promises to expand network bandwidth. Also introduced is the theory of dispersive virtual reference interferometry, which can be used to overcome the bandwidth limitations associated with the

  20. Using Virtual Reference Transcripts for Staff Training.

    ERIC Educational Resources Information Center

    Ward, David

    2003-01-01

    Describes a method of library staff training based on chat transcript analysis in which graduate student workers at a university reference desk examined transcripts of actual virtual reference desk transactions to analyze reference interviews. Discusses reference interview standards, reference desk behavior, and reference interview skills in…

  1. Sequence Factorization with Multiple References

    PubMed Central

    Wandelt, Sebastian; Leser, Ulf

    2015-01-01

    The success of high-throughput sequencing has lead to an increasing number of projects which sequence large populations of a species. Storage and analysis of sequence data is a key challenge in these projects, because of the sheer size of the datasets. Compression is one simple technology to deal with this challenge. Referential factorization and compression schemes, which store only the differences between input sequence and a reference sequence, gained lots of interest in this field. Highly-similar sequences, e.g., Human genomes, can be compressed with a compression ratio of 1,000:1 and more, up to two orders of magnitude better than with standard compression techniques. Recently, it was shown that the compression against multiple references from the same species can boost the compression ratio up to 4,000:1. However, a detailed analysis of using multiple references is lacking, e.g., for main memory consumption and optimality. In this paper, we describe one key technique for the referential compression against multiple references: The factorization of sequences. Based on the notion of an optimal factorization, we propose optimization heuristics and identify parameter settings which greatly influence 1) the size of the factorization, 2) the time for factorization, and 3) the required amount of main memory. We evaluate a total of 30 setups with a varying number of references on data from three different species. Our results show a wide range of factorization sizes (optimal to an overhead of up to 300%), factorization speed (0.01 MB/s to more than 600 MB/s), and main memory usage (few dozen MB to dozens of GB). Based on our evaluation, we identify the best configurations for common use cases. Our evaluation shows that multi-reference factorization is much better than single-reference factorization. PMID:26422374

  2. Virtual Reference, Real Money: Modeling Costs in Virtual Reference Services

    ERIC Educational Resources Information Center

    Eakin, Lori; Pomerantz, Jeffrey

    2009-01-01

    Libraries nationwide are in yet another phase of belt tightening. Without an understanding of the economic factors that influence library operations, however, controlling costs and performing cost-benefit analyses on services is difficult. This paper describes a project to develop a cost model for collaborative virtual reference services. This…

  3. Reference Anytime Anywhere: Towards Virtual Reference Services at Penn State.

    ERIC Educational Resources Information Center

    Moyo, Lesley M.

    2002-01-01

    Outlines the service rationale, software and technology considerations taken by the Pennsylvania State University library in planning towards online, real-time reference services and provides an overview of the planned pilot project. Discusses recent trends in academic electronic libraries, including providing value-added services to support…

  4. Reference Anywhere, Anytime: Recent Works on Virtual Reference

    ERIC Educational Resources Information Center

    Lindsay, Elizabeth Blakesley

    2008-01-01

    The topic of virtual reference has been a popular one in the past year, and this column highlights a range of those articles. Included are overviews of the topic, articles addressing specific technological solutions and concerns, and pieces that explore the intricacies of delivering and assessing a "traditional" service through a…

  5. The Virtual Reference Librarian: Using Desktop Videoconferencing for Distance Reference.

    ERIC Educational Resources Information Center

    Pagell, Ruth A.

    1996-01-01

    The Center for Business Information and the Goizueta Business School at Emory University (Georgia) tested desktop videoconferencing as a means to deliver reference services, including consultation, documentation, training, and sharing of CD-ROM databases. Provides a brief overview of the technology, describes project beta testing, and discusses…

  6. Reference and Reference Failures. Technical Report No. 398.

    ERIC Educational Resources Information Center

    Goodman, Bradley A.

    In order to build robust natural language processing systems that can detect and recover from miscommunication, the investigation of how people communicate and how they recover from problems in communication described in this artificial intelligence report focused on reference problems which a listener may have in determining what or whom a…

  7. Reference-based phasing using the Haplotype Reference Consortium panel.

    PubMed

    Loh, Po-Ru; Danecek, Petr; Palamara, Pier Francesco; Fuchsberger, Christian; A Reshef, Yakir; K Finucane, Hilary; Schoenherr, Sebastian; Forer, Lukas; McCarthy, Shane; Abecasis, Goncalo R; Durbin, Richard; L Price, Alkes

    2016-11-01

    Haplotype phasing is a fundamental problem in medical and population genetics. Phasing is generally performed via statistical phasing in a genotyped cohort, an approach that can yield high accuracy in very large cohorts but attains lower accuracy in smaller cohorts. Here we instead explore the paradigm of reference-based phasing. We introduce a new phasing algorithm, Eagle2, that attains high accuracy across a broad range of cohort sizes by efficiently leveraging information from large external reference panels (such as the Haplotype Reference Consortium; HRC) using a new data structure based on the positional Burrows-Wheeler transform. We demonstrate that Eagle2 attains a ∼20× speedup and ∼10% increase in accuracy compared to reference-based phasing using SHAPEIT2. On European-ancestry samples, Eagle2 with the HRC panel achieves >2× the accuracy of 1000 Genomes-based phasing. Eagle2 is open source and freely available for HRC-based phasing via the Sanger Imputation Service and the Michigan Imputation Server.

  8. PIRLA DBMS quick reference guide

    SciTech Connect

    Smith, J.

    1991-11-01

    The handbook facilitates the use of the PIRLA (Paleoecological Investigation of Recent Lake Acidification) database retrievals by showing all possible inputs, outputs, ranges, and quick reference information that you would want at your fingertips when accessing the PIRLA data. The handbook assumes no prior knowledge of PIRLA or SIR (a database management system), although a basic familiarity with computers is helpful. The PIRLA Data Base Management System User's Manual is recommended for reference, much additional detail, description of the intrinsic structure of the PIRLA database, and how it is set up under SIR.

  9. Tractor Transmissions. A Teaching Reference.

    ERIC Educational Resources Information Center

    American Association for Agricultural Engineering and Vocational Agriculture, Athens, GA.

    The manual was developed as a reference for teaching students about transmissions in farm tractors. The manual is divided into five sections: (1) transmission history, (2) gears and bearings in transmission, (3) sliding-gear transmissions, (4) planetary gearing, and (5) glossary. The working principles of the sliding-gear transmission, the most…

  10. When Is Cataphoric Reference Recognised?

    ERIC Educational Resources Information Center

    Filik, Ruth; Sanford, Anthony J.

    2008-01-01

    Pronouns typically have explicit antecedents in the prior discourse otherwise processing difficulty is experienced. However, it has been argued [Gordon, P. C., & Hendrick, R. (1997). "Intuitive knowledge of linguistic co-reference." "Cognition, 62", 325-370; Gordon, P. C., & Hendrick, R. (1998). "The representation and processing of co-reference…

  11. The Rosia Language Reference Manual

    DTIC Science & Technology

    1981-12-01

    Alternate database 16 Anaphora 26, 30, 56 Anaphoric reference 30 Arithmetic expressions 33 Arithmetic operators 8 Bind 54 Binding 54, 57 BNF 94...Descriptions as Class Membership Tests .......... 28 4.2.7. Descriptions and Modification ................... 29 4.2.8. Anaphoric Descriptions...54 4.9.3. Variable Binding ................................ 54 4.9.4. Pattern Matching ................................ 55 5

  12. Newfoundland. Reference Series No. 34.

    ERIC Educational Resources Information Center

    Department of External Affairs, Ottawa (Ontario).

    This booklet, one of a series featuring the Canadian provinces, presents a brief overview of Newfoundland and is suitable for teacher reference or student reading. Separate sections discuss geography and climate, history, economy, population and settlement, arts and culture, leisure and recreation, and heritage. Specific topics include the…

  13. Selected Reference Books of 1998.

    ERIC Educational Resources Information Center

    McIlvaine, Eileen

    1999-01-01

    Reviews a selection of recent scholarly and general reference works under the categories of Periodicals and Newspapers, Philosophy, Literature, Film and Radio, Art and Architecture, Music, Political Science, Women's Studies, and History. A brief summary of new editions of standard works is provided at the end of the articles. (AEF)

  14. Quebec. Reference Series No. 30.

    ERIC Educational Resources Information Center

    Department of External Affairs, Ottawa (Ontario).

    This booklet, one of a series featuring the Canadian provinces, presents a brief overview of Quebec and is suitable for teacher reference or student reading. Separate sections discuss geography, climate, population, history, political history, recent politics, agriculture, forestry, mining, manufacturing and industry, hydroelectric power,…

  15. [Developmental Placement.] Collected Research References.

    ERIC Educational Resources Information Center

    Bjorklund, Gail

    Drawing on information and references in the ERIC system, this literature review describes research related to a child's developmental placement. The issues examined include school entrance age; predictive validity, reliability, and features of Gesell School Readiness Assessment; retention; and the effectiveness of developmental placement. A…

  16. Manitoba. Reference Series No. 28.

    ERIC Educational Resources Information Center

    Department of External Affairs, Ottawa (Ontario).

    This booklet, one of a series featuring the Canadian provinces, presents a brief overview of Manitoba and is suitable for teacher reference or student reading. Separate sections discuss agriculture, mining, energy, transportation and communication, fishing, forestry, fur trapping, health and social services, education, and political life. Specific…

  17. Ontario. Reference Series No. 29.

    ERIC Educational Resources Information Center

    Department of External Affairs, Ottawa (Ontario).

    This booklet, one of a series featuring the Canadian provinces, presents a brief overview of Ontario and is suitable for teacher reference or student reading. Separate sections discuss geography, climate, history, agriculture, forestry, fishing, mining, manufacturing, transportation, energy, arts and culture, sports and recreation, and people and…

  18. Chapter 11: Dietary reference intakes

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The Dietary Reference Intakes (DRI) are a set of recommendations intended to provide guidance in evaluating nutrient intakes and planning meals on the basis of nutrient adequacy. In contrast to their predecessor, Recommended Dietary Allowances last published in 1989, the DRIs differ in two ways: th...

  19. A REFERENCE GRAMMAR OF BENGALI.

    ERIC Educational Resources Information Center

    RAY, PUNYA SLOKA; AND OTHERS

    A REFERENCE GRAMMAR WAS PRODUCED FOR THE BENGALI LANGUAGE. THE WORK CONTAINS CHAPTERS ON--(1) SOCIAL AND HISTORICAL BACKGROUND, (2) HISTORY OF THE LANGUAGE, (3) SOURCES OF LEXICAL ITEMS, (4) ORTHOGRAPHY, (5) PHONOLOGY, (6) NOUN INFLECTIONS, (7) VERBS, (8) POSTPOSITIONS, (9) ENCLITICS, (10) NUMERALS, (11) NEGATION, (12) FORMATIVE AFFIXES IN…

  20. Saskatchewan. Reference Series No. 27.

    ERIC Educational Resources Information Center

    Department of External Affairs, Ottawa (Ontario).

    This booklet, one of a series featuring the Canadian provinces, presents a brief overview of Saskatchewan and is suitable for teacher reference or student reading. Separate sections discuss history, economy, oil, uranium, potash, coal, minerals and metals, agriculture, forestry, tourism and recreation, arts and culture, and people. Specific topics…

  1. Reference Works in Reduced Size

    ERIC Educational Resources Information Center

    Hennessey, David

    1977-01-01

    Lower cost and less shelf space requirements have made major reference works in miniaturized print editions attractive to small libraries. The major disadvantage is the necessity of a magnifying glass for reading entries. A bibliography of reduced-size editions is included. (JAB)

  2. A Reference Grammar of Kashmiri.

    ERIC Educational Resources Information Center

    Kachru, Braj B.

    This study was developed for two pedagogical purposes--first, to provide a skeleton grammar of the Kashmiri language which could be used by teachers of Kashmiri to develop teaching materials for both Indian and non-Indian learners of Kashmiri; and second, to provide an introductory reference manual of Kashmiri for students of the language. The…

  3. Childhood Obesity. Special Reference Briefs.

    ERIC Educational Resources Information Center

    Winick, Myron

    This reference brief deals with the problem of childhood obesity and how it can lead to obesity in the adult. Eighty-four abstracts are presented of studies on the identification, prevention, and treatment of obesity in children, focusing on diet and psychological attitudes. Subjects of the studies were children ranging in age from infancy through…

  4. Guam and Micronesia Reference Sources.

    ERIC Educational Resources Information Center

    Goetzfridt, Nicholas J.; Goniwiecha, Mark C.

    1993-01-01

    This article lists reference sources for studying Guam and Micronesia. The entries are arranged alphabetically by main entry within each section in the categories of: (1) bibliographical works; (2) travel and guide books; (3) handbooks and surveys; (4) dictionaries; (5) yearbooks; (6) periodical and newspaper publications; and (7) audiovisual…

  5. Human Rights: The Essential Reference.

    ERIC Educational Resources Information Center

    Devine, Carol; Hansen, Carol Rae; Wilde, Ralph; Bronkhorst, Daan; Moritz, Frederic A.; Rolle, Baptiste; Sherman, Rebecca; Southard, Jo Lynn; Wilkinson, Robert; Poole, Hilary, Ed.

    This reference work documents the history of human rights theory, explains each article of the Universal Declaration of Human Rights, explores the contemporary human rights movement, and examines the major human rights issues facing the world today. This book is the first to combine historical and contemporary perspectives on these critical…

  6. Alberta. Reference Series No. 26.

    ERIC Educational Resources Information Center

    Department of External Affairs, Ottawa (Ontario).

    This booklet, one of a series featuring the Canadian provinces, presents a brief overview of Alberta and is suitable for teacher reference or student reading. Separate sections discuss the history and population, the provincial government, the economy, transportation, communications, mineral resources, agriculture, manufacturing, forest products,…

  7. Mobile Technologies and Roving Reference

    ERIC Educational Resources Information Center

    Penner, Katherine

    2011-01-01

    As 21st century librarians, we have made apt adjustments for reaching out into the digital world, but we need to consider the students who still use library services within our walls. We can use available handheld, mobile technologies to help patrons too shy to approach the desk and free library staff to bring reference service directly to patrons.

  8. Expert Systems in Reference Services.

    ERIC Educational Resources Information Center

    Roysdon, Christine, Ed.; White, Howard D., Ed.

    1989-01-01

    Eleven articles introduce expert systems applications in library and information science, and present design and implementation issues of system development for reference services. Topics covered include knowledge based systems, prototype development, the use of artificial intelligence to remedy current system inadequacies, and an expert system to…

  9. Selected Reference Books of 1992.

    ERIC Educational Resources Information Center

    McIlvaine, Eileen

    1993-01-01

    Presents an annotated bibliography of 40 recent scholarly and general works of interest to reference workers in university libraries. Topics areas covered include philosophy, religion, language, literature, architecture, economics, law, area studies, Russia and the Soviet Union, women's studies, and Christopher Columbus. New editions and…

  10. Thermocouple, multiple junction reference oven

    NASA Technical Reports Server (NTRS)

    Leblanc, L. P. (Inventor)

    1981-01-01

    An improved oven for maintaining the junctions of a plurality of reference thermocouples at a common and constant temperature is described. The oven is characterized by a cylindrical body defining a heat sink with axially extended-cylindrical cavity a singularized heating element which comprises a unitary cylindrical heating element consisting of a resistance heating coil wound about the surface of metallic spool with an axial bore defined and seated in the cavity. Other features of the oven include an annular array of radially extended bores defined in the cylindrical body and a plurality of reference thermocouple junctions seated in the bores in uniformly spaced relation with the heating element, and a temperature sensing device seated in the axial bore for detecting temperature changes as they occur in the spool and circuit to apply a voltage across the coil in response to detected drops in temperatures of the spool.

  11. ADAM -- Interface Module Reference Manual

    NASA Astrophysics Data System (ADS)

    Chipperfield, A. J.; Kelly, B. D.; Wright, S. L.

    ADAM Interface Modules provide an interface between ADAM application programs and the rest of the system. This document describes in detail the facilities available with ADAM Interface Modules and the rules for using them. It is intended as a reference manual and should shed light on some of the finer points of the ADAM parameter system. Readers requiring an introduction to Interface Modules should read SG/4.

  12. HANFORD WASTE MINEROLOGY REFERENCE REPORT

    SciTech Connect

    DISSELKAMP RS

    2010-06-18

    This report lists the observed mineral phase phases present in the Hanford tanks. This task was accomplished by performing a review of numerous reports using experimental techniques including, but not limited to: x-ray diffraction, polarized light microscopy, scanning electron microscopy, transmission electron microscopy, energy dispersive spectroscopy, electron energy loss spectroscopy, and particle size distribution analyses. This report contains tables that can be used as a quick reference to identify the crystal phases present observed in Hanford waste.

  13. HANFORD WASTE MINERALOGY REFERENCE REPORT

    SciTech Connect

    DISSELKAMP RS

    2010-06-29

    This report lists the observed mineral phases present in the Hanford tanks. This task was accomplished by performing a review of numerous reports that used experimental techniques including, but not limited to: x-ray diffraction, polarized light microscopy, scanning electron microscopy, transmission electron microscopy, energy dispersive spectroscopy, electron energy loss spectroscopy, and particle size distribution analyses. This report contains tables that can be used as a quick reference to identify the crystal phases observed in Hanford waste.

  14. National Software Reference Library (NSRL)

    National Institute of Standards and Technology Data Gateway

    National Software Reference Library (NSRL) (PC database for purchase)   A collaboration of the National Institute of Standards and Technology (NIST), the National Institute of Justice (NIJ), the Federal Bureau of Investigation (FBI), the Defense Computer Forensics Laboratory (DCFL),the U.S. Customs Service, software vendors, and state and local law enforement organizations, the NSRL is a tool to assist in fighting crime involving computers.

  15. Microgrid cyber security reference architecture.

    SciTech Connect

    Veitch, Cynthia K.; Henry, Jordan M.; Richardson, Bryan T.; Hart, Derek H.

    2013-07-01

    This document describes a microgrid cyber security reference architecture. First, we present a high-level concept of operations for a microgrid, including operational modes, necessary power actors, and the communication protocols typically employed. We then describe our motivation for designing a secure microgrid; in particular, we provide general network and industrial control system (ICS)-speci c vulnerabilities, a threat model, information assurance compliance concerns, and design criteria for a microgrid control system network. Our design approach addresses these concerns by segmenting the microgrid control system network into enclaves, grouping enclaves into functional domains, and describing actor communication using data exchange attributes. We describe cyber actors that can help mitigate potential vulnerabilities, in addition to performance bene ts and vulnerability mitigation that may be realized using this reference architecture. To illustrate our design approach, we present a notional a microgrid control system network implementation, including types of communica- tion occurring on that network, example data exchange attributes for actors in the network, an example of how the network can be segmented to create enclaves and functional domains, and how cyber actors can be used to enforce network segmentation and provide the neces- sary level of security. Finally, we describe areas of focus for the further development of the reference architecture.

  16. Reference Inflow Characterization for River Resource Reference Model (RM2)

    SciTech Connect

    Neary, Vincent S

    2011-12-01

    Sandia National Laboratory (SNL) is leading an effort to develop reference models for marine and hydrokinetic technologies and wave and current energy resources. This effort will allow the refinement of technology design tools, accurate estimates of a baseline levelized cost of energy (LCoE), and the identification of the main cost drivers that need to be addressed to achieve a competitive LCoE. As part of this effort, Oak Ridge National Laboratory was charged with examining and reporting reference river inflow characteristics for reference model 2 (RM2). Published turbulent flow data from large rivers, a water supply canal and laboratory flumes, are reviewed to determine the range of velocities, turbulence intensities and turbulent stresses acting on hydrokinetic technologies, and also to evaluate the validity of classical models that describe the depth variation of the time-mean velocity and turbulent normal Reynolds stresses. The classical models are found to generally perform well in describing river inflow characteristics. A potential challenge in river inflow characterization, however, is the high variability of depth and flow over the design life of a hydrokinetic device. This variation can have significant effects on the inflow mean velocity and turbulence intensity experienced by stationary and bottom mounted hydrokinetic energy conversion devices, which requires further investigation, but are expected to have minimal effects on surface mounted devices like the vertical axis turbine device designed for RM2. A simple methodology for obtaining an approximate inflow characterization for surface deployed devices is developed using the relation umax=(7/6)V where V is the bulk velocity and umax is assumed to be the near-surface velocity. The application of this expression is recommended for deriving the local inflow velocity acting on the energy extraction planes of the RM2 vertical axis rotors, where V=Q/A can be calculated given a USGS gage flow time

  17. Sentinel 2 global reference image

    NASA Astrophysics Data System (ADS)

    Dechoz, C.; Poulain, V.; Massera, S.; Languille, F.; Greslou, D.; de Lussy, F.; Gaudel, A.; L'Helguen, C.; Picard, C.; Trémas, T.

    2015-10-01

    Sentinel-2 is a multispectral, high-resolution, optical imaging mission, developed by the European Space Agency (ESA) in the frame of the Copernicus program of the European Commission. In cooperation with ESA, the Centre National d'Etudes Spatiales (CNES) is responsible for the image quality of the project, and will ensure the CAL/VAL commissioning phase. Sentinel-2 mission is devoted the operational monitoring of land and coastal areas, and will provide a continuity of SPOT- and Landsat-type data. Sentinel-2 will also deliver information for emergency services. Launched in 2015 and 2016, there will be a constellation of 2 satellites on a polar sun-synchronous orbit, imaging systematically terrestrial surfaces with a revisit time of 5 days, in 13 spectral bands in visible and shortwave infra-red. Therefore, multi-temporal series of images, taken under the same viewing conditions, will be available. So as to ensure for the multi-temporal registration of the products, specified to be better than 0.3 pixels at 2σ, a Global Reference Image (GRI) will be produced during the CAL/VAL period. This GRI is composed of a set of Sentinel-2 acquisitions, which geometry has been corrected by bundle block adjustment. During L1B processing, Ground Control Points will be taken between this reference image and the sentinel-2 acquisition processed and the geometric model of the image corrected, so as to ensure the good multi-temporal registration. This paper first details the production of the reference during the CALVAL period, and then details the qualification and geolocation performance assessment of the GRI. It finally presents its use in the Level-1 processing chain and gives a first assessment of the multi-temporal registration.

  18. PVWatts Version 1 Technical Reference

    SciTech Connect

    Dobos, A. P.

    2013-10-01

    The NREL PVWatts(TM) calculator is a web application developed by the National Renewable Energy Laboratory (NREL) that estimates the electricity production of a grid-connected photovoltaic system based on a few simple inputs. PVWatts combines a number of sub-models to predict overall system performance, and makes several hidden assumptions about performance parameters. This technical reference details the individual sub-models, documents assumptions and hidden parameters, and explains the sequence of calculations that yield the final system performance estimation.

  19. Concepts in Geodetic Reference Frames.

    DTIC Science & Technology

    1979-10-01

    in the years 1900-1905. The period of C around the origin is about 1.2 years, the Chandler period. The z-axis of the terrestrial coordinate system is...multiplication by the matrix W which expresses the effect of polar motion, also called polar wobble . It has the form 1 0 x w= 0 1 -y (6-4) -x y 1 where...reference. The periods of forced rnotion (of F, H, and I) are about 1 day, the period of free motion of S, C’ and E0 around 0 is the Chandler period of

  20. [Dietary reference intakes of phosphorus].

    PubMed

    Uenishi, Kazuhiro

    2012-10-01

    Phosphorus (P) exists at the all organs and plays important physiological roles in the body. A wide range of food contains P, which is absorbed at a higher level (60-70%) and its insufficiency and deficiency are rarely found. P is used as food additives in many processed food, where risk of overconsumption could be an issue. P has less evidence in terms of nutrition. P has the adequate intake and the tolerable upper intake level, for risk reduction of health disorders associated with excess intake, at the Dietary Reference Intakes for Japanese (2010 edition).

  1. World Reference Center for Arboviruses.

    DTIC Science & Technology

    1984-01-01

    flaviviruses recovered from pooled mosquitoes from Indonesia. Mous Reference Viruses JKT Arbo # Mouse immune ascitic fluids JE ME SEP THU ZIKA 5441 7180 9092...320 ɝ ɝ ɝ 5 Zika ( ZIKA ) 5 5 20 5 10 5 JKT Arbo # 5441 320 20 ɝ 160 ND 20 * ND not done F’, 41 r .• As more workers begin to use mosquito cells for...80 ɠ/4096 ᝺/81920 Zika 16/512 20/160 ɠ/4096 320/81920 Jutiapa 16/512 10/320 8/4096 160/81920 Yakose -- ɠ/4096 20/81920 Aroa -- ɠ/4096 ᝺/81920

  2. Ozone reference models for CIRA

    NASA Astrophysics Data System (ADS)

    Keating, G. M.; Young, D. F.; Pitts, M. C.

    The data bases and computational techniques used in recent models of the O3 distribution in the earth atmosphere are described, summarizing the results of ongoing efforts to define an O3 reference model for incorporation into CIRA. Consideration is given to the analysis of data from satellite instruments (Nimbus 7 LIMS, TOMS, and SBUV; SME UVS and IR; and AE-2 SAGE) to construct models of total column O3 and vertical O3 structure. The satellite-based model predictions are then compared with balloon, rocket, and umkehr measurements in extensive graphs: good agreement is demonstrated both among the satellite data sets and between satellite and nonsatellite data sets.

  3. Empirical Reference Models for COSPAR International Reference Atmosphere (CIRA)

    NASA Astrophysics Data System (ADS)

    Drob, Douglas; Emmert, John; Picone, Michael

    Openly distributed atmospheric reference models are an essential tool for scientific research and operational activities. To meet the needs of all users, such models must utilize rigorous statistical methods and the most comprehensive and reliable data sets in their development. Two such models that meet these requirements are the Naval Research Laboratory, Mass Spectrometer Incoherent Scatter Extended (NRLMSISE-00) and Horizontal Wind Model (HWM-93) empirical reference models. The NRLMSISE-00 model and its predecessors are based on 35 years of empirical modeling experience and over 40 years of research measurements. These global models are well documented and extend from the ground to the exosphere, providing estimates of neutral temperature, density, and major neutral species composition as a function of geographic location, day of year, time of day, and geomagnetic and solar activity conditions. Relative to the most comprehensive span of datasets available these models have the smallest bias and root mean square deviations of any climatological reference model built to date, although there are a few limitations in the 80 to 120 km region. The less advanced HWM-93 model, based on the same statistical methodologies and general mathematical formulation of the NRLMSISE-00 model, provides climatological estimates of the horizontal wind fields over the same variables and range of conditions as the NRLMSISE-00 model. The availability of several new long term data sets, including satellite wind measurements from the WINDII instrument onboard the UARS satellite, as well as ground-based optical Fabery-Perot measurements, provide the opportunity to make significant refinements to the existing model. Initial results from an improved HWM will be shown for altitudes between 100 and 500 km. Improvement in the model's ability to represent the seasonal changes, solar forcing, geomagnetic forcing, diurnal variation, and vertical structure of horizontal winds of the region is

  4. 40 CFR 1508.24 - Referring agency.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Referring agency. 1508.24 Section 1508.24 Protection of Environment COUNCIL ON ENVIRONMENTAL QUALITY TERMINOLOGY AND INDEX § 1508.24 Referring agency. Referring agency means the federal agency which has referred any matter to the...

  5. Virtual Reference for a Real Public.

    ERIC Educational Resources Information Center

    McDermott, Irene E.

    1998-01-01

    Reviews World Wide Web sites useful as alternative resources for reference librarians. Sites described are: general reference; reference for kids and teens; regional interest for Southern California, including local foreign-language resources and local history sites; and interactive reference. (JAK)

  6. The Art of Collection Development: Reference Style.

    ERIC Educational Resources Information Center

    Schmitt, John P.

    1998-01-01

    Discusses selecting for a reference collection, creative budgeting, cutting a deal, collection awareness (strengths/needs), Web site reviews, R-Net (reviews from diverse areas and institutions), and print vs. electronic reference products. Reference librarian adhere to high standards for reference book and Web sites, teach assessment techniques,…

  7. Instant Messaging Reference: How Does It Compare?

    ERIC Educational Resources Information Center

    Desai, Christina M.

    2003-01-01

    Compares a digital reference service that uses instant messaging with traditional, face-to-face reference based on experiences at the Southern Illinois University library. Addresses differences in reference questions asked, changes in the reference transaction, student expectations, bibliographic instruction, and librarian attitudes and procedures…

  8. Building and Maintaining Digital Reference Services.

    ERIC Educational Resources Information Center

    Wasik, Joann M.

    2000-01-01

    Discusses digital reference services that provide subject expertise and information referral over the Internet to their users. Describes the history of digital reference, how digital reference services work, and explains a six-step process for building and maintaining digital reference services, including training, planning, and evaluating. (LRW)

  9. Reference electrodes for underground storage tanks

    SciTech Connect

    Ansuini, F.J.; Dimond, J.R.

    1995-12-31

    This paper discusses several factors affecting the reference potential established by copper/copper sulfate and silver/silver chloride reference electrodes. Guidelines for using permanent references in underground storage tank applications are presented and some causes of misleading readings with portable references are discussed.

  10. Hypertext Cross-Reference Utilities

    NASA Astrophysics Data System (ADS)

    Warren-Smith, R. F.; Draper, P. W.

    This document describes a set of ``Hypertext Cross-Reference Utilities'' (HTX) which are designed to help maintain large documentation sets whose constituent documents are written using the Hypertext Markup Languagee (HTML). The central part of HTX is a hypertext linker, hlink. This allows hyper-links (or cross-references) to be established between related documents in such a way that it is easy to maintain their integrity as individual documents are updated. Information produced by this linking process is also used by other HTX utilities to provide document search facilities and the ability to randomly access any part of a documentation set. This latter capability forms a basis for constructing hypertext help systems for use by other software. The expected readership of this document includes those who read hypertext documentation, those who write it, and those who maintain it, especially those who write and maintain Starlink documentation. Software developers may also be interested in the possibilities for hypertext help that HTX provides.

  11. Event boundaries and anaphoric reference.

    PubMed

    Thompson, Alexis N; Radvansky, Gabriel A

    2016-06-01

    The current study explored the finding that parsing a narrative into separate events impairs anaphor resolution. According to the Event Horizon Model, when a narrative event boundary is encountered, a new event model is created. Information associated with the prior event model is removed from working memory. So long as the event model containing the anaphor referent is currently being processed, this information should still be available when there is no narrative event boundary, even if reading has been disrupted by a working-memory-clearing distractor task. In those cases, readers may reactivate their prior event model, and anaphor resolution would not be affected. Alternatively, comprehension may not be as event oriented as this account suggests. Instead, any disruption of the contents of working memory during comprehension, event related or not, may be sufficient to disrupt anaphor resolution. In this case, reading comprehension would be more strongly guided by other, more basic language processing mechanisms and the event structure of the described events would play a more minor role. In the current experiments, participants were given stories to read in which we included, between the anaphor and its referent, either the presence of a narrative event boundary (Experiment 1) or a narrative event boundary along with a working-memory-clearing distractor task (Experiment 2). The results showed that anaphor resolution was affected by narrative event boundaries but not by a working-memory-clearing distractor task. This is interpreted as being consistent with the Event Horizon Model of event cognition.

  12. Reference-assisted chromosome assembly.

    PubMed

    Kim, Jaebum; Larkin, Denis M; Cai, Qingle; Asan; Zhang, Yongfen; Ge, Ri-Li; Auvil, Loretta; Capitanu, Boris; Zhang, Guojie; Lewin, Harris A; Ma, Jian

    2013-01-29

    One of the most difficult problems in modern genomics is the assembly of full-length chromosomes using next generation sequencing (NGS) data. To address this problem, we developed "reference-assisted chromosome assembly" (RACA), an algorithm to reliably order and orient sequence scaffolds generated by NGS and assemblers into longer chromosomal fragments using comparative genome information and paired-end reads. Evaluation of results using simulated and real genome assemblies indicates that our approach can substantially improve genomes generated by a wide variety of de novo assemblers if a good reference assembly of a closely related species and outgroup genomes are available. We used RACA to reconstruct 60 Tibetan antelope (Pantholops hodgsonii) chromosome fragments from 1,434 SOAPdenovo sequence scaffolds, of which 16 chromosome fragments were homologous to complete cattle chromosomes. Experimental validation by PCR showed that predictions made by RACA are highly accurate. Our results indicate that RACA will significantly facilitate the study of chromosome evolution and genome rearrangements for the large number of genomes being sequenced by NGS that do not have a genetic or physical map.

  13. Coastwide Reference Monitoring System (CRMS)

    USGS Publications Warehouse

    2010-01-01

    In 1990, the U.S. Congress enacted the Coastal Wetlands Planning, Protection and Restoration Act (CWPPRA) in response to growing awareness of a land loss crisis in Louisiana. Projects funded by CWPPRA require monitoring and evaluation of project effectiveness, and there is also a need to assess the cumulative effects of all projects to achieve a sustainable coastal environment. In 2003, the Louisiana Office of Coastal Protection and Restoration (OCPR) and the U.S. Geological Survey (USGS) received approval from the CWPPRA Task Force to implement the Coastwide Reference Monitoring System (CRMS) as a mechanism to monitor and evaluate the effectiveness of CWPPRA projects at the project, region, and coastwide levels. The CRMS design implements a multiple reference approach by using aspects of hydrogeomorphic functional assessments and probabilistic sampling. The CRMS program is as dynamic as the coastal habitats it monitors. The program is currently funded through CWPPRA and provides data for a variety of user groups, including resource managers, academics, landowners, and researchers.

  14. Speaker Adaptation Using Multiple Reference Speakers

    DTIC Science & Technology

    1989-01-01

    to other methods that use a pooled reference model , this technique normalizes the training speech from multiple reference speakers to a single com...training the reference hidden Markov model (HMM). Our usual prohabilistic spectrum transformation can be applied to the reference HMM to model a new...trained phonetic hidden Markov models of a single reference speaker so that they were appropriate for a new (target) speaker. This method reduced the

  15. NUCLEAR SCIENCE REFERENCES CODING MANUAL

    SciTech Connect

    WINCHELL,D.F.

    2007-04-01

    This manual is intended as a guide for Nuclear Science References (NSR) compilers. The basic conventions followed at the National Nuclear Data Center (NNDC), which are compatible with the maintenance and updating of and retrieval from the Nuclear Science References (NSR) file, are outlined. The NSR database originated at the Nuclear Data Project (NDP) at Oak Ridge National Laboratory as part of a project for systematic evaluation of nuclear structure data.1 Each entry in this computer file corresponds to a bibliographic reference that is uniquely identified by a Keynumber and is describable by a Topic and Keywords. It has been used since 1969 to produce bibliographic citations for evaluations published in Nuclear Data Sheets. Periodic additions to the file were published as the ''Recent References'' issues of Nuclear Data Sheets prior to 2005. In October 1980, the maintenance and updating of the NSR file became the responsibility of the NNDC at Brookhaven National Laboratory. The basic structure and contents of the NSR file remained unchanged during the transfer. In Chapter 2, the elements of the NSR file such as the valid record identifiers, record contents, and text fields are enumerated. Relevant comments regarding a new entry into the NSR file and assignment of a keynumber are also given in Chapter 2. In Chapter 3, the format for keyword abstracts is given followed by specific examples; for each TOPIC, the criteria for inclusion of an article as an entry into the NSR file as well as coding procedures are described. Authors preparing Keyword abstracts either to be published in a Journal (e.g., Nucl. Phys. A) or to be sent directly to NNDC (e.g., Phys. Rev. C) should follow the illustrations in Chapter 3. The scope of 1See W.B.Ewbank, ORNL-5397 (1978). the literature covered at the NNDC, the categorization into Primary and Secondary sources, etc., is discussed in Chapter 4. Useful information regarding permitted character sets, recommended abbreviations, etc., is

  16. Primary Atomic Clock Reference System

    NASA Technical Reports Server (NTRS)

    2001-01-01

    An artist's concept of the Primary Atomic Clock Reference System (PARCS) plarned to fly on the International Space Station (ISS). PARCS will make even more accurate atomic time available to everyone, from physicists testing Einstein's Theory of Relativity, to hikers using the Global Positioning System to find their way. In ground-based atomic clocks, lasers are used to cool and nearly stop atoms of cesium whose vibrations are used as the time base. The microgravity of space will allow the atoms to be suspended in the clock rather than circulated in an atomic fountain, as required on Earth. PARCS is being developed by the Jet Propulsion Laboratory with principal investigators at the National Institutes of Standards and Technology and the University of Colorado, Boulder. See also No. 0103191

  17. Primary Atomic Clock Reference System

    NASA Technical Reports Server (NTRS)

    2001-01-01

    An artist's concept of the Primary Atomic Clock Reference System (PARCS) plarned to fly on the International Space Station (ISS). PARCS will make even more accurate atomic time available to everyone, from physicists testing Einstein's Theory of Relativity, to hikers using the Global Positioning System to find their way. In ground-based atomic clocks, lasers are used to cool and nearly stop atoms of cesium whose vibrations are used as the time base. The microgravity of space will allow the atoms to be suspended in the clock rather than circulated in an atomic fountain, as required on Earth. PARCS is being developed by the Jet Propulsion Laboratory with principal investigators at the National Institutes of Standards and Technology and the University of Colorado, Boulder. See also No. 0100120.

  18. Generic Crystalline Disposal Reference Case

    SciTech Connect

    Painter, Scott Leroy; Chu, Shaoping; Harp, Dylan Robert; Perry, Frank Vinton; Wang, Yifeng

    2015-02-20

    A generic reference case for disposal of spent nuclear fuel and high-level radioactive waste in crystalline rock is outlined. The generic cases are intended to support development of disposal system modeling capability by establishing relevant baseline conditions and parameters. Establishment of a generic reference case requires that the emplacement concept, waste inventory, waste form, waste package, backfill/buffer properties, EBS failure scenarios, host rock properties, and biosphere be specified. The focus in this report is on those elements that are unique to crystalline disposal, especially the geosphere representation. Three emplacement concepts are suggested for further analyses: a waste packages containing 4 PWR assemblies emplaced in boreholes in the floors of tunnels (KBS-3 concept), a 12-assembly waste package emplaced in tunnels, and a 32-assembly dual purpose canister emplaced in tunnels. In addition, three failure scenarios were suggested for future use: a nominal scenario involving corrosion of the waste package in the tunnel emplacement concepts, a manufacturing defect scenario applicable to the KBS-3 concept, and a disruptive glaciation scenario applicable to both emplacement concepts. The computational approaches required to analyze EBS failure and transport processes in a crystalline rock repository are similar to those of argillite/shale, with the most significant difference being that the EBS in a crystalline rock repository will likely experience highly heterogeneous flow rates, which should be represented in the model. The computational approaches required to analyze radionuclide transport in the natural system are very different because of the highly channelized nature of fracture flow. Computational workflows tailored to crystalline rock based on discrete transport pathways extracted from discrete fracture network models are recommended.

  19. Very preliminary reference Moon model

    NASA Astrophysics Data System (ADS)

    Garcia, Raphaël F.; Gagnepain-Beyneix, Jeannine; Chevrot, Sébastien; Lognonné, Philippe

    2011-09-01

    The deep structure of the Moon is a missing piece to understand the formation and evolution of the Earth-Moon system. Despite the great amount of information brought by the Apollo passive seismic experiment (ALSEP), the lunar structure below deep moonquakes, which occur around 900 km depth, remains largely unknown. We construct a reference Moon model which incorporates physical constraints, and fits both geodesic (lunar mass and polar moment of inertia, and Love numbers) and seismological (body wave arrivals measured by Apollo network) data. In this model, the core radius is constrained by the detection of S waves reflected from the core. In a first step, for each core radius, a radial model of the lunar interior, including P and S wave velocities and density, is inverted from seismic and geodesic data. In a second step, the core radius is determined from the detection of shear waves reflected on the lunar core by waveform stacking of deep moonquake Apollo records. This detection has been made possible by careful data selection and processing, including a correction of the gain of horizontal sensors based on the principle of energy equipartition inside the coda of lunar seismic records, and a precise alignment of SH waveforms by a non-linear inversion method. The Very Preliminary REference MOON model (VPREMOON) obtained here has a core radius of 380 ± 40 km and an average core mass density of 5200 ± 1000 kg/m 3. The large error bars on these estimates are due to the poorly constrained S-wave velocity profile at the base of the mantle and to mislocation errors of deep moonquakes. The detection of horizontally polarized S waves reflected from the core and the absence of detection of vertically polarized S waves favour a liquid state in the outermost part of the core. All these results are consistent, within their error bars, with previous estimates based on lunar rotation dissipation ( Williams et al., 2001) and on lunar induced magnetic moment ( Hood et al., 1999).

  20. Reference materials for cellular therapeutics.

    PubMed

    Bravery, Christopher A; French, Anna

    2014-09-01

    The development of cellular therapeutics (CTP) takes place over many years, and, where successful, the developer will anticipate the product to be in clinical use for decades. Successful demonstration of manufacturing and quality consistency is dependent on the use of complex analytical methods; thus, the risk of process and method drift over time is high. The use of reference materials (RM) is an established scientific principle and as such also a regulatory requirement. The various uses of RM in the context of CTP manufacturing and quality are discussed, along with why they are needed for living cell products and the analytical methods applied to them. Relatively few consensus RM exist that are suitable for even common methods used by CTP developers, such as flow cytometry. Others have also identified this need and made proposals; however, great care will be needed to ensure any consensus RM that result are fit for purpose. Such consensus RM probably will need to be applied to specific standardized methods, and the idea that a single RM can have wide applicability is challenged. Written standards, including standardized methods, together with appropriate measurement RM are probably the most appropriate way to define specific starting cell types. The characteristics of a specific CTP will to some degree deviate from those of the starting cells; consequently, a product RM remains the best solution where feasible. Each CTP developer must consider how and what types of RM should be used to ensure the reliability of their own analytical measurements.

  1. A reference architecture for telemonitoring.

    PubMed

    Clarke, Malcolm

    2004-01-01

    The Telecare Interactive Continuous Monitoring System exploits GPRS to provide an ambulatory device that monitors selected vital signs on a continuous basis. Alarms are sent when parameters fall outside preset limits, and accompanying physiological data may also be transmitted. The always-connected property of GPRS allows continuous interactive control of the device and its sensors, permitting changes to monitoring parameters or even enabling continuous monitoring of a sensor in emergency. A new personal area network (PAN) has been developed to support short-range wireless connection to sensors worn on the body including ECG and finger worn SpO2. Most notable is use of ultra low radio frequency to reduce power to minimum. The system has been designed to use a hierarchical architecture for sensors and "derived" signals, such as HR from ECG, so that each can be independently controlled and managed. Sensors are treated as objects, and functions are defined to control aspects of behaviour. These are refined in order to define a generic set of abstract functions to handle the majority of functions, leaving a minimum of sensor specific commands. The intention is to define a reference architecture in order to research the functionality and system architecture of a telemonitoring system. The Telecare project is funded through a grant from the European Commission (IST programme).

  2. Gender agreement and multiple referents.

    PubMed

    Finocchiaro, Chiara; Mahon, Bradford Z; Caramazza, Alfonso

    2008-01-01

    We report a new pattern of usage in current, spoken Italian that has implications for both psycholinguistic models of language production and linguistic theories of language change. In Italian, gender agreement is mandatory for both singular and plural nouns. However, when two or more nouns of different grammatical gender appear in a conjoined noun phrase (NP), masculine plural agreement is required. In this study, we combined on-line and off-line methodologies in order to assess the mechanisms involved in gender marking in the context of multiple referents. The results of two pronoun production tasks showed that plural feminine agreement was significantly more difficult than plural masculine agreement. In a separate study using offline judgements of acceptability, we found that agreement violations in Italian are tolerated more readily in the case of feminine conjoined noun phrases (e.g., la mela e la banana 'the:fem apple:fem and the: fem banana: fem') than masculine conjoined noun phrases (e.g., il fiore e il libro 'the:mas flower: mas and the:mas book:mas'). Implications of these results are discussed both at the level of functional architecture within the language production system and at the level of changes in language use.

  3. ILC cryogenic systems reference design

    SciTech Connect

    Peterson, T.J.; Geynisman, M.; Klebaner, A.; Theilacker, J.; Parma, V.; Tavian, L.; /CERN

    2008-01-01

    A Global Design Effort (GDE) began in 2005 to study a TeV scale electron-positron linear accelerator based on superconducting radio-frequency (RF) technology, called the International Linear Collider (ILC). In early 2007, the design effort culminated in a reference design for the ILC, closely based on the earlier TESLA design. The ILC will consist of two 250 GeV linacs, which provide positron-electron collisions for high energy physics research. The particle beams will be accelerated to their final energy in superconducting niobium RF cavities operating at 2 kelvin. At a length of about 12 km each, the main linacs will be the largest cryogenic systems in the ILC. Positron and electron sources, damping rings, and beam delivery systems will also have a large number and variety of other superconducting RF cavities and magnets, which require cooling at liquid helium temperatures. Ten large cryogenic plants with 2 kelvin refrigeration are envisioned to cool the main linacs and the electron and positron sources. Three smaller cryogenic plants will cool the damping rings and beam delivery system components predominately at 4.5 K. This paper describes the cryogenic systems concepts for the ILC.

  4. The Reference Forward Model (RFM)

    NASA Astrophysics Data System (ADS)

    Dudhia, Anu

    2017-01-01

    The Reference Forward Model (RFM) is a general purpose line-by-line radiative transfer model, currently supported by the UK National Centre for Earth Observation. This paper outlines the algorithms used by the RFM, focusing on standard calculations of terrestrial atmospheric infrared spectra followed by a brief summary of some additional capabilities and extensions to microwave wavelengths and extraterrestrial atmospheres. At its most basic level - the 'line-by-line' component - it calculates molecular absorption cross-sections by applying the Voigt lineshape to all transitions up to ±25 cm-1 from line-centre. Alternatively, absorptions can be directly interpolated from various forms of tabulated data. These cross-sections are then used to construct infrared radiance or transmittance spectra for ray paths through homogeneous cells, plane-parallel or circular atmospheres. At a higher level, the RFM can apply instrumental convolutions to simulate measurements from Fourier transform spectrometers. It can also calculate Jacobian spectra and so act as a stand-alone forward model within a retrieval scheme. The RFM is designed for robustness, flexibility and ease-of-use (particularly by the non-expert), and no claims are made for superior accuracy, or indeed novelty, compared to other line-by-line codes. Its main limitations at present are a lack of scattering and simplified modelling of surface reflectance and line-mixing.

  5. Gender agreement and multiple referents

    PubMed Central

    Finocchiaro, Chiara; Mahon, Bradford Z.; Caramazza, Alfonso

    2010-01-01

    We report a new pattern of usage in current, spoken Italian that has implications for both psycholinguistic models of language production and linguistic theories of language change. In Italian, gender agreement is mandatory for both singular and plural nouns. However, when two or more nouns of different grammatical gender appear in a conjoined noun phrase (NP), masculine plural agreement is required. In this study, we combined on-line and off-line methodologies in order to assess the mechanisms involved in gender marking in the context of multiple referents. The results of two pronoun production tasks showed that plural feminine agreement was significantly more difficult than plural masculine agreement. In a separate study using offline judgements of acceptability, we found that agreement violations in Italian are tolerated more readily in the case of feminine conjoined noun phrases (e.g., la mela e la banana ‘the:fem apple:fem and the: fem banana: fem’) than masculine conjoined noun phrases (e.g., il fiore e il libro ‘the:mas flower: mas and the:mas book:mas’). Implications of these results are discussed both at the level of functional architecture within the language production system and at the level of changes in language use.* PMID:21037930

  6. Establishment of reference standards in biosimilar studies.

    PubMed

    Zhang, Aijing; Tzeng, Jung-Ying; Chow, Shein-Chung

    2013-07-31

    When an innovative biological product goes off-patent, biopharmaceutical or biotechnological companies may file an application for regulatory approval of biosimilar products. In practice, however, important information on the innovative (reference) product may not be available for assessment. Thus, it is important to first establish a reference standard while assessing biosimilarity between a biosimilar product and the reference product. In this paper, reference standard is established through the biosimilarity index approach based on a reference-replicated study (or R-R study), in which the reference product is compared with itself under various scenarios. The reference standard can then be used for assessing the degree of similarity between the test and reference drugs in biosimilar studies.

  7. 33 CFR 242.3 - References.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 33 Navigation and Navigable Waters 3 2014-07-01 2014-07-01 false References. 242.3 Section 242.3 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE FLOOD PLAIN MANAGEMENT SERVICES PROGRAM ESTABLISHMENT OF FEES FOR COST RECOVERY § 242.3 References. The references...

  8. 33 CFR 242.3 - References.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 33 Navigation and Navigable Waters 3 2012-07-01 2012-07-01 false References. 242.3 Section 242.3 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE FLOOD PLAIN MANAGEMENT SERVICES PROGRAM ESTABLISHMENT OF FEES FOR COST RECOVERY § 242.3 References. The references...

  9. Suggested References. PACE I.D. Center.

    ERIC Educational Resources Information Center

    Bergson, Rita

    During the course of the PACE I.D. Center Project, 1966-1969, staff members recorded references that they felt contributed to the general knowledge of the prevention of learning and behavior problems. More specifically, those references that implied concern for the child in his total environment were considered most relevant. The references are…

  10. Virtual Reference Services: Directions and Agendas.

    ERIC Educational Resources Information Center

    Gray, Suzanne M.

    2000-01-01

    Analyzes Web sites of ten large research libraries in order to establish a basic understanding of how some major libraries are currently providing virtual reference services. Discusses centralization; email reference guidelines; creating a service economy; expanding hours of service; virtual users' needs; and real-time virtual reference.…

  11. Rethinking Job References: A Networking Challenge

    ERIC Educational Resources Information Center

    Muir, Clive

    2009-01-01

    Can job references play an active role in shaping one's career plans? Would individuals consider their references as part of their personal and professional network? Although most professionals may respond with a resounding "Yes, of course!" to these questions, the author realized that many of his students were skeptical about job references. To…

  12. Environmental Sciences Reference Sources. An Annotated Bibliography.

    ERIC Educational Resources Information Center

    McMartin, Mary I., Comp.

    This list of Environmental Sciences References Sources is intended to give undergraduate and graduate students a starting point when searching for information in the library. Entries are grouped according to type of reference material and then are listed in alphabetical order. The types of reference material included are guides to dictionaries,…

  13. Frames of Reference in the Classroom

    ERIC Educational Resources Information Center

    Grossman, Joshua

    2012-01-01

    The classic film "Frames of Reference" effectively illustrates concepts involved with inertial and non-inertial reference frames. In it, Donald G. Ivey and Patterson Hume use the cameras perspective to allow the viewer to see motion in reference frames translating with a constant velocity, translating while accelerating, and rotating--all with…

  14. Applying Information Competency to Digital Reference.

    ERIC Educational Resources Information Center

    Ellis, Lisa; Francoeur, Stephen

    This paper presents a case for applying information competency (IC) standards to digital reference services at academic libraries. Practical reasons for applying standards or guidelines to e-mail and online chat reference services are given with some insight to the nature of digital reference interactions. The standards that arose from the…

  15. Quality Standards for Digital Reference Consortia.

    ERIC Educational Resources Information Center

    Kasowitz, Abby; Bennett, Blythe; Lankes, R. David

    2000-01-01

    Identifies a working set of standards by which to assess individual digital reference services (Internet-based human-mediated information services) and to define membership within a collaborative network of digital reference services. The standards are designed for the Virtual Reference Desk AskA Consortium. (Author/LRW)

  16. Reference and the First Person Pronoun.

    ERIC Educational Resources Information Center

    Glock, Hans-Johann; Hacker, P. M. S.

    1996-01-01

    Maintains that deciding whether the first person pronoun is a referring expression requires clarity about the role of "I" and a detailed account of the notion of reference. It is concluded that "I" is a limiting case of reference, in which the possibility of referential failure and misidentification does not apply. (24…

  17. 40 CFR 1043.100 - Reference materials.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 33 2014-07-01 2014-07-01 false Reference materials. 1043.100 Section... § 1043.100 Reference materials. Documents listed in this section have been incorporated by reference into... the availability of this material at NARA, call 202-741-6030, or go to:...

  18. 40 CFR 1042.910 - Reference materials.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 33 2014-07-01 2014-07-01 false Reference materials. 1042.910 Section... Other Reference Information § 1042.910 Reference materials. Documents listed in this section have been... information on the availability of this material at NARA, call 202-741-6030, or go to:...

  19. 40 CFR 1042.910 - Reference materials.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Reference materials. 1042.910 Section... Other Reference Information § 1042.910 Reference materials. Documents listed in this section have been... information on the availability of this material at NARA, call 202-741-6030, or go to:...

  20. 40 CFR 94.5 - Reference materials.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 20 2011-07-01 2011-07-01 false Reference materials. 94.5 Section 94.5... Compression-Ignition Marine Engines § 94.5 Reference materials. We have incorporated by reference the... availability of this material at NARA, call 202-741-6030, or go to:...

  1. 40 CFR 1043.100 - Reference materials.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Reference materials. 1043.100 Section... § 1043.100 Reference materials. Documents listed in this section have been incorporated by reference into... the availability of this material at NARA, call 202-741-6030, or go to:...

  2. 40 CFR 1043.100 - Reference materials.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 34 2012-07-01 2012-07-01 false Reference materials. 1043.100 Section... § 1043.100 Reference materials. Documents listed in this section have been incorporated by reference into... the availability of this material at NARA, call 202-741-6030, or go to:...

  3. 40 CFR 1042.910 - Reference materials.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 34 2012-07-01 2012-07-01 false Reference materials. 1042.910 Section... Other Reference Information § 1042.910 Reference materials. Documents listed in this section have been... information on the availability of this material at NARA, call 202-741-6030, or go to:...

  4. Reference electrodes for aboveground storage tanks

    SciTech Connect

    Ansuini, F.J.; Dimond, J.R.

    1995-12-31

    This paper discusses several factors affecting the reference potential established by copper/copper sulfate and silver/silver chloride reference electrodes. Guidelines for using references in aboveground storage tank applications are presented and some causes of misleading readings are discussed.

  5. Evaluating Reference Services and Reference Personnel: Questions and Answers from the Literature.

    ERIC Educational Resources Information Center

    Bunge, Charles A.

    1994-01-01

    This bibliographic essay discusses a variety of items from the literature on the evaluation of reference services and reference personnel. A model for the evaluation process is presented on which the literature review is based. (Contains 48 references.) (LRW)

  6. Writing More Informative Letters of Reference

    PubMed Central

    Wright, Scott M; Ziegelstein, Roy C

    2004-01-01

    Writing a meaningful and valuable letter of reference is not an easy task. Several factors influence the quality of any letter of reference. First, the accuracy and reliability of the writer's impressions and judgment depend on how well he knows the individual being described. Second, the writer's frame of reference, which is determined by the number of persons at the same level that he has worked with, will impact the context and significance of his beliefs and estimations. Third, the letter-writing skills of the person composing the letter will naturally affect the letter. To support the other components of a candidate's application, a letter of reference should provide specific examples of how an individual's behavior or attitude compares to a reference group and should assess “intangibles” that are hard to glean from a curriculum vitae or from test scores. This report offers suggestions that should help physicians write more informative letters of reference. PMID:15109330

  7. Quantum metrology in coarsened measurement reference

    NASA Astrophysics Data System (ADS)

    Xie, Dong; Xu, Chunling; Wang, An Min

    2017-01-01

    We investigate the role of coarsened measurement reference, which originates from the coarsened reference time and basis, in quantum metrology. When the measurement is based on one common reference basis, the disadvantage of coarsened measurement can be removed by symmetry. Owing to the coarsened reference basis, the entangled state cannot perform better than the product state for a large number of probe particles in estimating the phase. Given a finite uncertainty of the coarsened reference basis, the optimal number of probe particles is obtained. Finally, we prove that the maximally entangled state always achieves better frequency precision in the case of non-Markovian dephasing than that in the case of Markovian dephasing. The product state is more resistant to the interference of the coarsened reference time than the entangled state.

  8. Minimize reference sideband generation in microwave PLLs

    NASA Astrophysics Data System (ADS)

    Goldman, Stan

    1991-02-01

    The processes responsible for producing reference sidebands are outlined, and the sources of coupling to the microwave voltage-controlled oscillator (VCO) tune line including power-supply-generated signals, TTL-controlled interface signals, intermediate programmable-divider signals, and radiated TTL signals are discussed. It is noted that filtering alone is inadequate for reference-sideband suppression, while minimizing the tuning slope and maximizing the reference frequency will result in a reduced reference-sideband level. Minimizing offset currents by using a differential amplifier connection may reduce the reference-sideband level aggravated by an opamp. The selection of a TTL, ECL, or GaAs phase/frequency detector can determine the level of reference sidebands, as well as PCB isolation techniques.

  9. ["Pro Ana": Psychodynamic References for Anorexia Nervosa].

    PubMed

    Siefert, Linda

    2017-02-01

    "Pro Ana": Psychodynamic References for Anorexia Nervosa The internet-based phenomenon "Pro Ana" refers to the eating disorder anorexia nervosa in a positive way. To understand what the phenomenon "Pro Ana" represents, the websites are used as a starting point of the current analysis. Based on these results, similarities and differences between "Pro Ana" and the eating disorder anorexia nervosa are discussed. Furthermore psychodynamic references for anorexia nervosa are derived and finally their importance for treatment motivation will be considered.

  10. Biological and environmental reference materials: Update 1996

    NASA Astrophysics Data System (ADS)

    Roelandts, Iwan

    1997-07-01

    The present column lists additional biological and environmental reference samples. Organs, tissues, body fluids, plant materials, foods, fuels, ashes, dusts, particulate matter, gas mixtures, oils, soils, sediments, sludges and waters have been considered. Three tables are included that provide an easy-to-use survey. The following information is covered: the name of the material, the sample code, the producer, the reference to certification, the names and addresses of the suppliers from whom the reference material may be obtained, and specific remarks.

  11. A standard satellite control reference model

    NASA Technical Reports Server (NTRS)

    Golden, Constance

    1994-01-01

    This paper describes a Satellite Control Reference Model that provides the basis for an approach to identify where standards would be beneficial in supporting space operations functions. The background and context for the development of the model and the approach are described. A process for using this reference model to trace top level interoperability directives to specific sets of engineering interface standards that must be implemented to meet these directives is discussed. Issues in developing a 'universal' reference model are also identified.

  12. An improved hypothetical reference decoder for HEVC

    NASA Astrophysics Data System (ADS)

    Deshpande, Sachin; Hannuksela, Miska M.; Kazui, Kimihiko; Schierl, Thomas

    2013-02-01

    Hypothetical Reference Decoder is a hypothetical decoder model that specifies constraints on the variability of conforming network abstraction layer unit streams or conforming byte streams that an encoding process may produce. High Efficiency Video Coding (HEVC) builds upon and improves the design of the generalized hypothetical reference decoder of H.264/ AVC. This paper describes some of the main improvements of hypothetical reference decoder of HEVC.

  13. Reference materials for new psychoactive substances.

    PubMed

    Archer, Roland P; Treble, Ric; Williams, Keith

    2011-01-01

    Historically, the appearance of new psychoactive materials (and hence the requirement for new reference standards) has been relatively slow. This position has now changed, with 101 new psychoactive substances reported to EMCDDA-Europol since 2006. The newly reported materials, and associated metabolites, require properly certified reference materials to permit reliable identification and quantification. The traditional approach and timescales of reference material production and certification are being increasingly challenged by the appearance of these new substances. Reference material suppliers have to adopt new strategies to meet the needs of laboratories. This situation is particularly challenging for toxicology standards as the metabolism of many of these substances is initially unknown. Reference material production often involves synthesis from first principles. While it is possible to synthesis these materials, there can be significant difficulties, from synthetic complexities through to the need to use controlled materials. These issues are examined through a discussion of the synthesis of cathinones. Use of alternative sources, including pharmaceutical impurity materials or internet sourced products, as starting materials for conversion into appropriately certified reference materials are also discussed. The sudden appearance and sometimes brief lifetime in the market place of many of these novel legal highs or research chemicals present commercial difficulties for reference material producers. The need for collaboration at all levels is highlighted as essential to rapid identification of requirements for new reference materials. National or international commissioning or support may also be required to permit reference material producers to recover their development costs.

  14. Resources and References for Earth Science Teachers

    ERIC Educational Resources Information Center

    Wall, Charles A.; Wall, Janet E.

    1976-01-01

    Listed are resources and references for earth science teachers including doctoral research, new textbooks, and professional literature in astronomy, space science, earth science, geology, meteorology, and oceanography. (SL)

  15. Nuclear-driven electron spin rotations in a coupled silicon quantum dot and single donor system

    NASA Astrophysics Data System (ADS)

    Harvey-Collard, Patrick; Jacobson, Noah Tobias; Rudolph, Martin; Ten Eyck, Gregory A.; Wendt, Joel R.; Pluym, Tammy; Lilly, Michael P.; Pioro-Ladrière, Michel; Carroll, Malcolm S.

    Single donors in silicon are very good qubits. However, a central challenge is to couple them to one another. To achieve this, many proposals rely on using a nearby quantum dot (QD) to mediate an interaction. In this work, we demonstrate the coherent coupling of electron spins between a single 31P donor and an enriched 28Si metal-oxide-semiconductor few-electron QD. We show that the electron-nuclear spin interaction can drive coherent rotations between singlet and triplet electron spin states. Moreover, we are able to tune electrically the exchange interaction between the QD and donor electrons. The combination of single-nucleus-driven rotations and voltage-tunable exchange provides all elements for future all-electrical control of a spin qubit, and requires only a single dot and no additional magnetic field gradients. This work was performed, in part, at the Center for Integrated Nanotechnologies, an Office of Science User Facility operated for the U.S. Department of Energy (DOE) Office of Science. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. DOE's National Nuclear Security Administration under Contract DE-AC04-94AL85000.

  16. Nuclear-Driven Copper-Based Hybrid Thermo/Electro Chemical Cycle for Hydrogen Production

    SciTech Connect

    Khalil, Yehia F.; Rostkowski, Katherine H.

    2006-07-01

    With a worldwide need for reduction of greenhouse gas emissions, hydrogen gas has become a primary focus of energy researchers as a promising substitute of nonrenewable energy sources. For instance, use of hydrogen gas in fuel cells has received special technological interest particularly from the transportation sector, which is presently dominated by fuel oil. It is not only gaseous hydrogen that is in demand, but the need for liquid hydrogen is growing as well. For example, the aerospace industry uses liquid hydrogen as fuel for space shuttles. The use of liquid hydrogen during a single space shuttle launch requires about 15,000 gallons per minute, which is equivalent to about forty-five hydrogen trailers, each with 13,000 gallons capacity. The hydrogen required to support a single Mars mission would be at least ten times that required for one space shuttle launch. In this work, we provide mass and energy balances, major equipment sizing, and costing of a hybrid CuO-CuSO{sub 4} plant with 1000 MW (30,240 kg/hr) H{sub 2} production capacity. With a 90% annual availability factor, the estimated hydrogen production rate is about 238,412 tons annually, the predicted plant efficiency is about 36%, and the estimated hydrogen production cost is about $4.0/kg (not including storage and transportation costs). In addition to hydrogen production, the proposed plant generates oxygen gas as a byproduct with an estimated flowrate of about 241,920 kg/hr (equivalent to 1,907,297 tons annually). We also propose a novel technology for separating SO{sub 2} and SO{sub 3} from O{sub 2} using a battery of redundant fixed-bed reactors containing CuO impregnated in porous alumina (Al{sub 2}O{sub 3}). This technology accommodates online regeneration of the CuO. Other practical approaches for gaseous separation are also examined including use of ceramic membranes, liquefaction, and regenerable wet scrubbing with slurried magnesium oxide or solutions of sodium salts such as sodium sulfite and sodium hydroxide. Finally, we discuss the applicability of high-temperature nuclear reactors as an ideal fit to providing thermal energy and electricity required for operating the hybrid thermochemical plant with high overall system efficiency. (authors)

  17. Nuclear-driven flashlamp pumping of the atomic iodine laser. Final report

    SciTech Connect

    Miley, G.H.

    1992-03-01

    This report is a study of the atomic iodine laser pumped with nuclear- excited XeBr fluorescence. Preliminary experiments, conducted in the TRIGA reactor investigated the fluorescence of the excimer XeBr under nuclear pumping with {sup 10}B and {sup 3}He, for use as a flashlamp gas to stimulate the laser. These measurements included a determination of the fluorescence efficiency (light emitted in the wavelength region of interest, divided by energy deposited in the gas) of XeBr under nuclear pumping, with varying excimer mixtures. Maximum fluorescence efficiencies were approximately 1%. In order to better understand XeBr under nuclear excitation, a kinetics model of the system was prepared. The model generated the time-dependant concentrations of 20 reaction species for three pulse sizes, a TRIGA pulse, a fast burst reactor pulse, and an e-beam pulse. The modeling results predicted fluorescence efficiencies significantly higher (peak efficiencies of approximately 10%) than recorded in the fluorescence experiments. The cause of this discrepancy was not fully determined. A ray tracing computer model was also prepared to evaluate the efficiency with which nuclear-induced fluorescence generated in one cavity of a laser could be coupled into another cavity containing an iodine lasant. Finally, an experimental laser cell was constructed to verify that nuclear-induced XeBr fluorescence could be used to stimulate a laser. Lasing was achieved at 1.31 micron in the TRIGA using C{sub 3}F{sub 7}I, a common iodine lasant. Peak laser powers were approximately 20 mW. Measured flashlamp pump powers at threshold agreed well with literature values, as did lasant pressure dependency on laser operation.

  18. 44 CFR 59.4 - References.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... INSURANCE AND HAZARD MITIGATION National Flood Insurance Program GENERAL PROVISIONS General § 59.4 References. (a) The following are statutory references for the National Flood Insurance Program, under which these regulations are issued: (1) National Flood Insurance Act of 1968 (title XIII of the Housing...

  19. 44 CFR 59.4 - References.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... INSURANCE AND HAZARD MITIGATION National Flood Insurance Program GENERAL PROVISIONS General § 59.4 References. (a) The following are statutory references for the National Flood Insurance Program, under which these regulations are issued: (1) National Flood Insurance Act of 1968 (title XIII of the Housing...

  20. 4 CFR 2.2 - References.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 4 Accounts 1 2012-01-01 2012-01-01 false References. 2.2 Section 2.2 Accounts GOVERNMENT ACCOUNTABILITY OFFICE PERSONNEL SYSTEM PURPOSE AND GENERAL PROVISION § 2.2 References. (a) Subchapters III and IV of Chapter 7 of Title 31 U.S.C. (b) Title 5, United States Code....

  1. 4 CFR 2.2 - References.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 4 Accounts 1 2014-01-01 2013-01-01 true References. 2.2 Section 2.2 Accounts GOVERNMENT ACCOUNTABILITY OFFICE PERSONNEL SYSTEM PURPOSE AND GENERAL PROVISION § 2.2 References. (a) Subchapters III and IV of Chapter 7 of Title 31 U.S.C. (b) Title 5, United States Code....

  2. 4 CFR 2.2 - References.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 4 Accounts 1 2013-01-01 2013-01-01 false References. 2.2 Section 2.2 Accounts GOVERNMENT ACCOUNTABILITY OFFICE PERSONNEL SYSTEM PURPOSE AND GENERAL PROVISION § 2.2 References. (a) Subchapters III and IV of Chapter 7 of Title 31 U.S.C. (b) Title 5, United States Code....

  3. RASD's New Interlibrary Reference Request Form.

    ERIC Educational Resources Information Center

    American Libraries, 1985

    1985-01-01

    Introduces information request form developed by Cooperative Reference Services Committee of American Library Association's Reference and Adult Services Division to be used whenever a library cannot supply information requested by a patron and would like to ask another library for assistance. Front of proposed form with sample question is shown.…

  4. Uncertainty in Reference and Information Service

    ERIC Educational Resources Information Center

    VanScoy, Amy

    2015-01-01

    Introduction: Uncertainty is understood as an important component of the information seeking process, but it has not been explored as a component of reference and information service. Method: Interpretative phenomenological analysis was used to examine the practitioner perspective of reference and information service for eight academic research…

  5. 40 CFR 1066.710 - Reference materials.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Practice for Measuring Fuel Economy and Emissions of Hybrid-Electric and Conventional Heavy-Duty Vehicles, Issued September 2002, IBR approved for § 1066.501. (c) National Institute of Standards and Technology... VEHICLE-TESTING PROCEDURES Definitions and Other Reference Material § 1066.710 Reference materials....

  6. Economics: A Guide to Reference Sources.

    ERIC Educational Resources Information Center

    Mason, Mary, Comp.

    Approximately 84 reference materials on economics located in the McLennan Library, McGill University (Montreal), are cited in this annotated bibliography. The bibliography serves to provide an overview of the printed bibliographic and reference sources useful for the study of economics. Financial and business sources and statistical compendia and…

  7. Reference. Advisory List of Instructional Media.

    ERIC Educational Resources Information Center

    North Carolina State Dept. of Public Education, Raleigh.

    The reference books featured in this annotated bibliography were selected from those titles that publishers submitted to the North Carolina Department of Public Instruction for review. As such, it is not a comprehensive list of all reference titles in print. This guide organizes the 33 titles into major subject categories: (1) Arts…

  8. Reference Services Planning in the 90s.

    ERIC Educational Resources Information Center

    Eckwright, Gail Z., Ed.; Keenan, Lori M., Ed.

    The focus of this collection of papers about library reference service is on the community outside the library, rather than the special populations served within it. "Conflicts in Value Systems" (Allen B. Veaner) is an overview of the major conflict areas facing the library profession today. "Reference Services for Off-Campus…

  9. Invoking Digital Reference: Creation and Implementation

    ERIC Educational Resources Information Center

    Johnson, Wendell; Burke, Adam

    2003-01-01

    In response to the changing educational landscape of the community college, reference librarians must adapt their service to fit the information needs of their patrons. One such update is synchronous digital reference, which applies instant messaging technology to library service. Todd Library at Waubonsee Community College (Sugar Grove, Illinois)…

  10. 32 CFR 1290.1 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 6 2010-07-01 2010-07-01 false References. 1290.1 Section 1290.1 National Defense Other Regulations Relating to National Defense DEFENSE LOGISTICS AGENCY MISCELLANEOUS PREPARING AND PROCESSING MINOR OFFENSES AND VIOLATION NOTICES REFERRED TO U.S. DISTRICT COURTS §...

  11. 4 CFR 2.2 - References.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 4 Accounts 1 2011-01-01 2011-01-01 false References. 2.2 Section 2.2 Accounts GOVERNMENT ACCOUNTABILITY OFFICE PERSONNEL SYSTEM PURPOSE AND GENERAL PROVISION § 2.2 References. (a) Subchapters III and IV of Chapter 7 of Title 31 U.S.C. (b) Title 5, United States Code....

  12. 4 CFR 2.2 - References.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 4 Accounts 1 2010-01-01 2010-01-01 false References. 2.2 Section 2.2 Accounts GOVERNMENT ACCOUNTABILITY OFFICE PERSONNEL SYSTEM PURPOSE AND GENERAL PROVISION § 2.2 References. (a) Subchapters III and IV of Chapter 7 of Title 31 U.S.C. (b) Title 5, United States Code....

  13. So You Want To Do Virtual Reference?

    ERIC Educational Resources Information Center

    Coffman, Steve

    2001-01-01

    Examines the practical details of setting up live online reference services in libraries. Topics include choosing software; differences between licensed and hosted applications; models used to implement virtual reference services; how libraries are using these services in day to day operations; and marketing strategies. (Author/LRW)

  14. Going Prime Time with Live Chat Reference.

    ERIC Educational Resources Information Center

    Hoag, Tara J.; Cichanowicz, Edana McCaffrey

    2001-01-01

    Describes the development of the Suffolk Cooperative Library System's live, online chat reference service, a pilot project for public libraries in Suffolk County (New York). Topics include chat software selection; a virtual reference collection; marketing; funding; staffing; evaluation; expanded hours of service; email; and extracting data from…

  15. Ensuring Quality in a Virtual Reference Environment

    ERIC Educational Resources Information Center

    Barbier, Pat; Ward, Joyce

    2004-01-01

    Soon after AskALibrarian, Florida's Statewide Virtual Reference Desk, began to offer Chat Reference to the public in 2003, a Quality Assurance Workgroup was established to ensure that the service patrons received would be friendly, accurate, and adequate. To make certain that best practices were used in answering the real time questions, two…

  16. Reference Service in the Information Network.

    ERIC Educational Resources Information Center

    Bunge, Charles A.

    Reference service is defined as the mediation by a librarian between the need structures of users and the structures of information resources. The general process by which reference librarians accomplish this is outlined as including the phases of question clarification, question translation, search strategy formulation, search execution, delivery…

  17. Responsive Reference Service: Breaking Down Age Barriers.

    ERIC Educational Resources Information Center

    Bunge, Charles A.

    1994-01-01

    Examines possible barriers to adequate reference services to children and young adults. Topics discussed include the effects of budget pressures and shifting priorities in public and academic libraries; equity in access to information; reference policies; communication between children and adult services staff and administration; multiple service…

  18. Search Analysts as Successful Reference Librarians.

    ERIC Educational Resources Information Center

    Hammer, Mary M.

    1981-01-01

    Examines five factors critical to the successful functioning of search analysts as reference librarians: professional training, background knowledge and working experience in references services, personality characteristics and interpersonal skills, the marketing of online services, and patron evaluations supplemented by postsearch reference…

  19. 21 CFR 660.52 - Reference preparations.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 7 2012-04-01 2012-04-01 false Reference preparations. 660.52 Section 660.52 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) BIOLOGICS... preparations. Reference Anti-Human Globulin preparations shall be obtained from the Center for...

  20. 21 CFR 660.52 - Reference preparations.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 7 2011-04-01 2010-04-01 true Reference preparations. 660.52 Section 660.52 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) BIOLOGICS... preparations. Reference Anti-Human Globulin preparations shall be obtained from the Center for...

  1. 21 CFR 660.52 - Reference preparations.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 7 2014-04-01 2014-04-01 false Reference preparations. 660.52 Section 660.52 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) BIOLOGICS... preparations. Reference Anti-Human Globulin preparations shall be obtained from the Center for...

  2. 21 CFR 660.52 - Reference preparations.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 7 2010-04-01 2010-04-01 false Reference preparations. 660.52 Section 660.52 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) BIOLOGICS... preparations. Reference Anti-Human Globulin preparations shall be obtained from the Center for...

  3. 21 CFR 660.52 - Reference preparations.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 7 2013-04-01 2013-04-01 false Reference preparations. 660.52 Section 660.52 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) BIOLOGICS... preparations. Reference Anti-Human Globulin preparations shall be obtained from the Center for...

  4. 32 CFR 518.2 - References.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 32 National Defense 3 2012-07-01 2009-07-01 true References. 518.2 Section 518.2 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY AID OF CIVIL AUTHORITIES AND PUBLIC RELATIONS THE FREEDOM OF INFORMATION ACT PROGRAM General Provisions § 518.2 References. Required and...

  5. 32 CFR 518.2 - References.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 32 National Defense 3 2011-07-01 2009-07-01 true References. 518.2 Section 518.2 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY AID OF CIVIL AUTHORITIES AND PUBLIC RELATIONS THE FREEDOM OF INFORMATION ACT PROGRAM General Provisions § 518.2 References. Required and...

  6. 32 CFR 518.2 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 3 2010-07-01 2010-07-01 true References. 518.2 Section 518.2 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY AID OF CIVIL AUTHORITIES AND PUBLIC RELATIONS THE FREEDOM OF INFORMATION ACT PROGRAM General Provisions § 518.2 References. Required and...

  7. 33 CFR 214.3 - Reference.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Reference. 214.3 Section 214.3 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE EMERGENCY SUPPLIES OF DRINKING WATER § 214.3 Reference. (a) Pub. L. 84-99, as amended (33 U.S.C. 701n). (b) Pub....

  8. Information Entrepreneurship: Sources for Reference Librarians.

    ERIC Educational Resources Information Center

    Gilton, Donna L.

    1992-01-01

    Discusses information entrepreneurs, or information brokers, and information intrapreneurship, or the establishment of fee-based information services within a library. Annotations are provided for 56 information sources that include general materials, research in these areas, and relationships with traditional reference services. (four references)…

  9. 47 CFR 15.11 - Cross reference.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 47 Telecommunication 1 2011-10-01 2011-10-01 false Cross reference. 15.11 Section 15.11 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES General § 15.11 Cross reference. The provisions of subparts A, H, I, J and K of part 2 apply to intentional and unintentional...

  10. 47 CFR 15.11 - Cross reference.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 47 Telecommunication 1 2010-10-01 2010-10-01 false Cross reference. 15.11 Section 15.11 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES General § 15.11 Cross reference. The provisions of subparts A, H, I, J and K of part 2 apply to intentional and unintentional...

  11. 47 CFR 15.11 - Cross reference.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 47 Telecommunication 1 2014-10-01 2014-10-01 false Cross reference. 15.11 Section 15.11 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES General § 15.11 Cross reference. The provisions of subparts A, H, I, J and K of part 2 apply to intentional and unintentional...

  12. 47 CFR 15.11 - Cross reference.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 47 Telecommunication 1 2013-10-01 2013-10-01 false Cross reference. 15.11 Section 15.11 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES General § 15.11 Cross reference. The provisions of subparts A, H, I, J and K of part 2 apply to intentional and unintentional...

  13. 47 CFR 15.11 - Cross reference.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 1 2012-10-01 2012-10-01 false Cross reference. 15.11 Section 15.11 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES General § 15.11 Cross reference. The provisions of subparts A, H, I, J and K of part 2 apply to intentional and unintentional...

  14. Writing references and using citation management software.

    PubMed

    Sungur, Mukadder Orhan; Seyhan, Tülay Özkan

    2013-09-01

    The correct citation of references is obligatory to gain scientific credibility, to honor the original ideas of previous authors and to avoid plagiarism. Currently, researchers can easily find, cite and store references using citation management software. In this review, two popular citation management software programs (EndNote and Mendeley) are summarized.

  15. Referent Salience Affects Second Language Article Use

    ERIC Educational Resources Information Center

    Trenkic, Danijela; Pongpairoj, Nattama

    2013-01-01

    The effect of referent salience on second language (L2) article production in real time was explored. Thai (-articles) and French (+articles) learners of English described dynamic events involving two referents, one visually cued to be more salient at the point of utterance formulation. Definiteness marking was made communicatively redundant with…

  16. 33 CFR 236.3 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false References. 236.3 Section 236.3 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE WATER... QUALITY § 236.3 References. (a) PL 89-72 (b) ER 1105-2-10 (c) ER 1105-2-200...

  17. 21 CFR 660.3 - Reference panel.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... ADDITIONAL STANDARDS FOR DIAGNOSTIC SUBSTANCES FOR LABORATORY TESTS Antibody to Hepatitis B Surface Antigen § 660.3 Reference panel. A Reference Hepatitis B Surface Antigen Panel shall be obtained from the Center... shall be used for determining the potency and specificity of Antibody to Hepatitis B Surface Antigen....

  18. 21 CFR 660.3 - Reference panel.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... STANDARDS FOR DIAGNOSTIC SUBSTANCES FOR LABORATORY TESTS Antibody to Hepatitis B Surface Antigen § 660.3 Reference panel. A Reference Hepatitis B Surface Antigen Panel shall be obtained from the Center for... used for determining the potency and specificity of Antibody to Hepatitis B Surface Antigen....

  19. 21 CFR 660.3 - Reference panel.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... ADDITIONAL STANDARDS FOR DIAGNOSTIC SUBSTANCES FOR LABORATORY TESTS Antibody to Hepatitis B Surface Antigen § 660.3 Reference panel. A Reference Hepatitis B Surface Antigen Panel shall be obtained from the Center... shall be used for determining the potency and specificity of Antibody to Hepatitis B Surface Antigen....

  20. 21 CFR 660.3 - Reference panel.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... ADDITIONAL STANDARDS FOR DIAGNOSTIC SUBSTANCES FOR LABORATORY TESTS Antibody to Hepatitis B Surface Antigen § 660.3 Reference panel. A Reference Hepatitis B Surface Antigen Panel shall be obtained from the Center... shall be used for determining the potency and specificity of Antibody to Hepatitis B Surface Antigen....

  1. How to Allocate Personnel Costs of Reference.

    ERIC Educational Resources Information Center

    Spencer, Carol

    In July 1974, at the American Library Association Convention, a symposium on reference measurement was held. The basic premise was that work sampling and random time sampling with self-observation were the best methods of allocating personnel costs of reference services at the Library of the College of Physicians of Philadelphia. First, reasons…

  2. 21 CFR 660.3 - Reference panel.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... ADDITIONAL STANDARDS FOR DIAGNOSTIC SUBSTANCES FOR LABORATORY TESTS Antibody to Hepatitis B Surface Antigen § 660.3 Reference panel. A Reference Hepatitis B Surface Antigen Panel shall be obtained from the Center... shall be used for determining the potency and specificity of Antibody to Hepatitis B Surface Antigen....

  3. 33 CFR 273.12 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false References. 273.12 Section 273.12 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE AQUATIC PLANT CONTROL § 273.12 References. (a) Section 302, Pub. L. 89-298, (79 Stat. 1092), Rivers and...

  4. Russian History; A Guide to Reference Sources.

    ERIC Educational Resources Information Center

    McGill Univ., Montreal (Quebec). McLennan Library.

    This guide identifies reference sources for the study of Russian and Soviet history available in the McGill University (Montreal) McLennan Library. Russian, English, French, and German language works covering Russian history from its origins to World War II are included. The guide is arranged in two parts: general reference sources and…

  5. English Language Arts. Delaware Teachers' Desk Reference.

    ERIC Educational Resources Information Center

    Delaware State Dept. of Education, Dover.

    This document represents one section of the Delaware Teachers' Desk Reference to Standards and Performance Indicators for Curriculum Planning and Unit Development produced by the Delaware Department of Education. The Desk Reference is part of the Delaware Department of Education's ongoing efforts to provide assistance and support to local school…

  6. Reference Sources: Little Known to Basic

    ERIC Educational Resources Information Center

    RQ, 1970

    1970-01-01

    This article lists seventy-eight reference sources, and is divided into the following four sections: (1) Useful But Little-Known Reference Tools by John Fetros, (2) The Statesman's Year-Book by James Becker, (3) Single Volume Scientific Encyclopedias by Jack Clarke and (4) Ten Basic Sources of Business and Economic Statistics by James Woy. (MF)

  7. 47 CFR 15.705 - Cross reference.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 1 2012-10-01 2012-10-01 false Cross reference. 15.705 Section 15.705 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES Television Band Devices § 15.705 Cross reference. (a) The provisions of subparts A, B, and C of this part apply to TVBDs, except...

  8. 47 CFR 15.705 - Cross reference.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 47 Telecommunication 1 2010-10-01 2010-10-01 false Cross reference. 15.705 Section 15.705 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES Television Band Devices § 15.705 Cross reference. (a) The provisions of subparts A, B, and C of this part apply to TVBDs, except...

  9. American Reference Books Annual 1974. Fifth Edition.

    ERIC Educational Resources Information Center

    Wynar, Bohdan S., Ed.; And Others

    The fifth edition of American Reference Books Annual (ARBA 74) provides a comprehensive listing of reference books published or distributed in the United States with 1973 imprints, plus those published too late in 1972 to be included in the fourth edition. Like other editions of ARBA, ARBA 74 reviews library science publications, reprints, and…

  10. Advanced Food Science and Nutrition Reference Book.

    ERIC Educational Resources Information Center

    Texas Tech Univ., Lubbock. Home Economics Curriculum Center.

    Developed with input from personnel in the industries, this reference book complements the curriculum guide for a laboratory course on the significance of nutrition in food science. The reference book is organized into 25 chapters, each beginning with essential elements and objectives. Within the text, italicized, bold-faced vocabulary terms are…

  11. Assessing Quality in Digital Reference Services.

    ERIC Educational Resources Information Center

    Lankes, R. David; Mcclure, Charles R.; Gross, Melissa

    2001-01-01

    Outlines a study to develop methods to assess the quality of digital reference services, test and refine measures and quality standards to describe digital reference services, and to produce a guidebook that describes how to collect and report data for these measures and standards. (Author/AEF)

  12. Creating an Instant Messaging Reference System.

    ERIC Educational Resources Information Center

    Fagan, Jody Condit; Calloway, Michele

    2001-01-01

    Discussion of library digital reference services focuses on the features of instant messaging reference systems and the in-house development of a system that incorporates them at Southern Illinois University at Carbondale. Summarizes and evaluates library chat system features and compares commercial software that is available. (Author/LRW)

  13. Live Reference: Too Much, Too Fast?

    ERIC Educational Resources Information Center

    Janes, Joe

    2002-01-01

    Considers the current trend in libraries toward live, or digital, reference services. Highlights include models for reference, including synchronous versus asynchronous; benefits for users; software packages; user expectations; suitability of the technology; and determining the best service for users and their information needs. (LRW)

  14. Virtual Reference Transcript Analysis: A Few Models.

    ERIC Educational Resources Information Center

    Smyth, Joanne

    2003-01-01

    Describes the introduction of virtual, or digital, reference service at the University of New Brunswick libraries. Highlights include analyzing transcripts from LIVE (Library Information in a Virtual Environment); reference question types; ACRL (Association of College and Research Libraries) information literacy competency standards; and the Big 6…

  15. What's Wrong with Collaborative Digital Reference?

    ERIC Educational Resources Information Center

    Coffman, Steve

    2002-01-01

    Questions the need for collaborative digital reference services among libraries. Discusses the lack of use among networks that have been developed, probably due to easy access to online resources; economic assumptions; setting standards for reference practice; automatic routing software; copyrights; and patron satisfaction. (LRW)

  16. Health physics research reactor reference dosimetry

    SciTech Connect

    Sims, C.S.; Ragan, G.E.

    1987-06-01

    Reference neutron dosimetry is developed for the Health Physics Research Reactor (HPRR) in the new operational configuration directly above its storage pit. This operational change was physically made early in CY 1985. The new reference dosimetry considered in this document is referred to as the 1986 HPRR reference dosimetry and it replaces any and all HPRR reference documents or papers issued prior to 1986. Reference dosimetry is developed for the unshielded HPRR as well as for the reactor with each of five different shield types and configurations. The reference dosimetry is presented in terms of three different dose and six different dose equivalent reporting conventions. These reporting conventions cover most of those in current use by dosimetrists worldwide. In addition to the reference neutron dosimetry, this document contains other useful dosimetry-related data for the HPRR in its new configuration. These data include dose-distance measurements and calculations, gamma dose measurements, neutron-to-gamma ratios, ''9-to-3 inch'' ratios, threshold detector unit measurements, 56-group neutron energy spectra, sulfur fluence measurements, and details concerning HPRR shields. 26 refs., 11 figs., 31 tabs.

  17. 32 CFR 651.2 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 4 2010-07-01 2010-07-01 true References. 651.2 Section 651.2 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) ENVIRONMENTAL QUALITY ENVIRONMENTAL ANALYSIS OF ARMY ACTIONS (AR 200-2) Introduction § 651.2 References. Required and related publications...

  18. 32 CFR 651.2 - References.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 32 National Defense 4 2013-07-01 2013-07-01 false References. 651.2 Section 651.2 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) ENVIRONMENTAL QUALITY ENVIRONMENTAL ANALYSIS OF ARMY ACTIONS (AR 200-2) Introduction § 651.2 References. Required and related publications...

  19. 32 CFR 651.2 - References.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 32 National Defense 4 2011-07-01 2011-07-01 false References. 651.2 Section 651.2 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) ENVIRONMENTAL QUALITY ENVIRONMENTAL ANALYSIS OF ARMY ACTIONS (AR 200-2) Introduction § 651.2 References. Required and related publications...

  20. 32 CFR 651.2 - References.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 32 National Defense 4 2012-07-01 2011-07-01 true References. 651.2 Section 651.2 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) ENVIRONMENTAL QUALITY ENVIRONMENTAL ANALYSIS OF ARMY ACTIONS (AR 200-2) Introduction § 651.2 References. Required and related publications...

  1. 32 CFR 651.2 - References.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 32 National Defense 4 2014-07-01 2013-07-01 true References. 651.2 Section 651.2 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) ENVIRONMENTAL QUALITY ENVIRONMENTAL ANALYSIS OF ARMY ACTIONS (AR 200-2) Introduction § 651.2 References. Required and related publications...

  2. Reach for Reference. Grolier's The Civil War

    ERIC Educational Resources Information Center

    Safford, Barbara Ripp

    2005-01-01

    This column describes Grolier's new ten-volume reference set, "The Civil War." The volumes are easy to handle and the set's appearance is designed to appeal to middle level students. Arrangement is alphabetical from Abolition in volume one to Zouaves in volume ten with reasonable cross references to other relevant articles. Each volume contains a…

  3. 47 CFR 2.1031 - Cross reference.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 47 Telecommunication 1 2011-10-01 2011-10-01 false Cross reference. 2.1031 Section 2.1031 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL FREQUENCY ALLOCATIONS AND RADIO TREATY MATTERS; GENERAL RULES AND REGULATIONS Equipment Authorization Procedures Certification § 2.1031 Cross reference....

  4. 47 CFR 2.1031 - Cross reference.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 47 Telecommunication 1 2013-10-01 2013-10-01 false Cross reference. 2.1031 Section 2.1031 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL FREQUENCY ALLOCATIONS AND RADIO TREATY MATTERS; GENERAL RULES AND REGULATIONS Equipment Authorization Procedures Certification § 2.1031 Cross reference....

  5. 47 CFR 2.1031 - Cross reference.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 1 2012-10-01 2012-10-01 false Cross reference. 2.1031 Section 2.1031 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL FREQUENCY ALLOCATIONS AND RADIO TREATY MATTERS; GENERAL RULES AND REGULATIONS Equipment Authorization Procedures Certification § 2.1031 Cross reference....

  6. 47 CFR 2.951 - Cross reference.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 47 Telecommunication 1 2013-10-01 2013-10-01 false Cross reference. 2.951 Section 2.951 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL FREQUENCY ALLOCATIONS AND RADIO TREATY MATTERS; GENERAL RULES AND REGULATIONS Equipment Authorization Procedures Verification § 2.951 Cross reference....

  7. 47 CFR 2.1031 - Cross reference.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 47 Telecommunication 1 2010-10-01 2010-10-01 false Cross reference. 2.1031 Section 2.1031 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL FREQUENCY ALLOCATIONS AND RADIO TREATY MATTERS; GENERAL RULES AND REGULATIONS Equipment Authorization Procedures Certification § 2.1031 Cross reference....

  8. 47 CFR 2.951 - Cross reference.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 47 Telecommunication 1 2010-10-01 2010-10-01 false Cross reference. 2.951 Section 2.951 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL FREQUENCY ALLOCATIONS AND RADIO TREATY MATTERS; GENERAL RULES AND REGULATIONS Equipment Authorization Procedures Verification § 2.951 Cross reference....

  9. 47 CFR 2.951 - Cross reference.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 47 Telecommunication 1 2011-10-01 2011-10-01 false Cross reference. 2.951 Section 2.951 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL FREQUENCY ALLOCATIONS AND RADIO TREATY MATTERS; GENERAL RULES AND REGULATIONS Equipment Authorization Procedures Verification § 2.951 Cross reference....

  10. 47 CFR 2.951 - Cross reference.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 1 2012-10-01 2012-10-01 false Cross reference. 2.951 Section 2.951 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL FREQUENCY ALLOCATIONS AND RADIO TREATY MATTERS; GENERAL RULES AND REGULATIONS Equipment Authorization Procedures Verification § 2.951 Cross reference....

  11. 47 CFR 2.1031 - Cross reference.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 47 Telecommunication 1 2014-10-01 2014-10-01 false Cross reference. 2.1031 Section 2.1031 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL FREQUENCY ALLOCATIONS AND RADIO TREATY MATTERS; GENERAL RULES AND REGULATIONS Equipment Authorization Procedures Certification § 2.1031 Cross reference....

  12. 47 CFR 2.951 - Cross reference.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 47 Telecommunication 1 2014-10-01 2014-10-01 false Cross reference. 2.951 Section 2.951 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL FREQUENCY ALLOCATIONS AND RADIO TREATY MATTERS; GENERAL RULES AND REGULATIONS Equipment Authorization Procedures Verification § 2.951 Cross reference....

  13. Lincoln Park Zoological Gardens Reference Library.

    ERIC Educational Resources Information Center

    Shaw, Joyce M.

    1988-01-01

    Describes the range of services offered by the Lincoln Park Zoological Gardens reference library, and discusses the concept of zoos as societal entities and future trends in their information requirements. A bibliography of 20 articles on library and information services in zoos and aquariums is included. (17 references) (Author/CLB)

  14. World Reference Center for Arboviruses and Retroviruses

    DTIC Science & Technology

    1988-05-01

    Reference Center for Arboviruses and Retroviruses identified viruses from Thailand, Nepal, Egypt, Colombia, and Panama. Cache Valley virus from a recruit...ARBOVIRUSES . . 13 A. Study of viruses from Thailand and Nepal . . . . 13 B. Isolation of Sicilian sandfly fever virus from Egyptian phlebotomines...dengue viruses ..... . 30 VII. LOW PASSAGE VIRUS COLLECTION .... ............. 32 VIII. ARBOVIRUS BULLETIN BOARD, REFERENCE, AND DATA ACCESS . 32 IX

  15. Accuracy of References in Five Entomology Journals.

    ERIC Educational Resources Information Center

    Kristof, Cynthia

    ln this paper, the bibliographical references in five core entomology journals are examined for citation accuracy in order to determine if the error rates are similar. Every reference printed in each journal's first issue of 1992 was examined, and these were compared to the original (cited) publications, if possible, in order to determine the…

  16. 32 CFR 516.2 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 3 2010-07-01 2010-07-01 true References. 516.2 Section 516.2 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY AID OF CIVIL AUTHORITIES AND PUBLIC RELATIONS LITIGATION General § 516.2 References. Applicable publications and forms are listed in appendix A to...

  17. Integrative analysis of 111 reference human epigenomes

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The reference human genome sequence set the stage for studies of genetic variation and its association with human disease, but epigenomic studies lack a similar reference. To address this need, the NIH Roadmap Epigenomics Consortium generated the largest collection so far of human epigenomes for pri...

  18. Jewish Studies: A Guide to Reference Sources.

    ERIC Educational Resources Information Center

    McGill Univ., Montreal (Quebec). McLennan Library.

    An annotated bibliography to the reference sources for Jewish Studies in the McLennan Library of McGill University (Canada) is presented. Any titles in Hebrew characters are listed by their transliterated equivalents. There is also a list of relevant Library of Congress Subject Headings. General reference sources listed are: encyclopedias,…

  19. Flexible Educational Facilities. An Annotated Reference List.

    ERIC Educational Resources Information Center

    Wakefield, Howard E.

    These references on flexible educational facilities are abstracted by the ERIC Clearinghouse on Educational Facilities. College material includes an experimental learning center, a college health center, a fine arts center, and university library design. References on schools include secondary school design, flexible high school design, standard…

  20. Adaptive Control with Reference Model Modification

    NASA Technical Reports Server (NTRS)

    Stepanyan, Vahram; Krishnakumar, Kalmanje

    2012-01-01

    This paper presents a modification of the conventional model reference adaptive control (MRAC) architecture in order to improve transient performance of the input and output signals of uncertain systems. A simple modification of the reference model is proposed by feeding back the tracking error signal. It is shown that the proposed approach guarantees tracking of the given reference command and the reference control signal (one that would be designed if the system were known) not only asymptotically but also in transient. Moreover, it prevents generation of high frequency oscillations, which are unavoidable in conventional MRAC systems for large adaptation rates. The provided design guideline makes it possible to track a reference commands of any magnitude from any initial position without re-tuning. The benefits of the method are demonstrated with a simulation example

  1. Alcohol references on undergraduate males' Facebook profiles.

    PubMed

    Egan, Katie G; Moreno, Megan A

    2011-09-01

    Perceived peer alcohol use is a predictor of consumption in college males; frequent references to alcohol on Facebook may encourage alcohol consumption. Content analysis of college males' Facebook profiles identified references to alcohol. The average age of 225 identified profiles was 19.9 years. Alcohol references were present on 85.3% of the profiles; the prevalence of alcohol was similar across each undergraduate grade. The average number of alcohol references per profile was 8.5 but increased with undergraduate year (p = .003; confidence interval = 1.5, 7.5). Students who were of legal drinking age referenced alcohol 4.5 times more than underage students, and an increase in number of Facebook friends was associated with an increase in displayed alcohol references (p < .001; confidence interval = 0.009, 0.02). Facebook is widely used in the college population; widespread alcohol displays on Facebook may influence social norms and cause increases in male college students' alcohol use.

  2. MSDS sky reference and preamplifier study

    NASA Technical Reports Server (NTRS)

    Larsen, L.; Stewart, S.; Lambeck, P.

    1974-01-01

    The major goals in re-designing the Multispectral Scanner and Data System (MSDS) sky reference are: (1) to remove the sun-elevation angle and aircraft-attitude angle dependence from the solar-sky illumination measurement, and (2) to obtain data on the optical state of the atmosphere. The present sky reference is dependent on solar elevation and provides essentially no information on important atmospheric parameters. Two sky reference designs were tested. One system is built around a hyperbolic mirror and the reflection approach. A second approach to a sky reference utilizes a fish-eye lens to obtain a 180 deg field of view. A detailed re-design of the present sky reference around the fish-eye approach, even with its limitations, is recommended for the MSDS system. A preamplifier study was undertaken to find ways of improving the noise-equivalent reflectance by reducing the noise level for silicon detector channels on the MSDS.

  3. Reference pricing and firms' pricing strategies.

    PubMed

    Miraldo, Marisa

    2009-01-01

    Within a horizontal differentiation model and allowing for heterogeneous qualities, we analyze the effects of reference pricing reimbursement on firms' pricing strategies. With this analysis we find inherent incentives for firms' pricing behavior, and consequently we shed some light on the time consistency of such policy. The analysis encompasses different reference price rules: (i) reference price as the minimum of the observed prices in the market, (ii) reference price as a linear combination of firms' prices. Results show that under the "minimum policy" firms are not able to coordinate on higher prices while the "linear policy", implicitly, provides a coordination device. We have also found that, relatively to the "linear policy", when the reference price is the minimum of observed prices, after policy implementation, total and private expenditures are higher and consumer surplus and firms' profits are lower. With quality differentiation both the minimum and linear policies unambiguously lead to higher prices.

  4. What Determines the Response: Test or Reference?

    NASA Technical Reports Server (NTRS)

    Chukova, S. V.; Ahumada, A. J., Jr.; Null, Cynthia (Technical Monitor)

    1998-01-01

    The stability of sensory memory has been studied by presenting a reference stimulus, a delay, and a test stimulus. As has been pointed out by Lages and Treisman (1998 Vision Research 38 557-572), the usual measure of performance depends only on the effect of test variations on the responses. The Weber fraction characterizing performance is more properly called the test stimulus Weber fraction. We measure the relative contribution of the test and reference to the response by the ratio of the test Weber fraction to the reference Weber fraction. The stimuli were two dark lines on a bright background. Seven reference separations, varying from 9.5 to 16.7 arc min, were intermixed in each run. Interstimulus intervals (ISI) of 50, 200 and 2000 msec and intertrial intervals (ITI) of 500 and 2500 msec were investigated. When the ISI was short (50 or 200 msec), for both ITIs, responses were determined equally by the test and reference. For the long ISI (2000 msec), the reference stimulus contributed less. However, only for the 500 msec ITI (and not for all observers) was the contribution of the reference stimulus negligible, as Treisman's criterion setting theory might suggest.

  5. Revised reference values for selenium intake.

    PubMed

    Kipp, A P; Strohm, D; Brigelius-Flohé, R; Schomburg, L; Bechthold, A; Leschik-Bonnet, E; Heseker, H

    2015-10-01

    The German, Austrian and Swiss nutrition societies are the joint editors of the 'reference values for nutrient intake'. They have revised the reference values for the intake of selenium and published them in February 2015. The saturation of selenoprotein P (SePP) in plasma is used as a criterion for the derivation of reference values for selenium intake in adults. For persons from selenium-deficient regions (China) SePP saturation was achieved with a daily intake of 49μg of selenium. When using the reference body weights the D-A-CH reference values are based upon, the resulting estimated value for selenium intake is 70μg/day for men and 60μg/day for women. The estimated value for selenium intake for children and adolescents is extrapolated using the estimated value for adults in relation to body weight. For infants aged 0 to under 4 months the estimated value of 10μg/day was derived from the basis of selenium intake via breast milk. For infants aged 4 to under 12 months this estimated value was used and taking into account the differences regarding body weight an estimated value of 15μg/day was derived. For lactating women compared to non-lactating women a higher reference value of 75μg/day is indicated due to the release of selenium with breast milk. The additional selenium requirement for pregnant women is negligible, so that no increased reference value is indicated.

  6. Reference materials and reference measurement systems in laboratory medicine. Harmonization of nomenclature and definitions in reference measurement systems.

    PubMed

    Dybkaer, R

    1995-12-01

    Reliability of clinical laboratory results is obtained through quality assurance in both their production and transmission. The former involves a reference measurement system of reference materials and reference measurement procedures with metrological and statistical verification of results. The latter requires that sender and receiver have access to a common terminology. Thus, two data banks are required. A plurilingual systematic vocabulary related to the reference measurement system, giving concepts with terms and definitions concerning measurement standards, reference measurement procedures, internal quality control, external quality assessment, probability and statistics-mainly based on existing authoritative publications. The material should be processed by standard scientific terminological procedure and offered to pertinent organizations and specialists for comment before finalization and authorization. A multilingual collection of systematic names for properties examined by the branches of Laboratory Medicine, such as clinical chemistry, clinical immunology, clinical microbiology, clinical pharmacology, haematology and blood banking, and histochemistry and cytology. The database should function as a reference to consultation and as a link in the transmission of data between local laboratory "dialects". This should be based on the ongoing comprehensive IUPAC/IFCC project for forming names in collaboration with relevant scientific organisations and area specialists. The relational data base including "run-time" software would be accessed by e-mail (gopher or other storage medium).

  7. Development of solid thorium-232 reference materials

    NASA Astrophysics Data System (ADS)

    Engelder, P. R.; Donivan, S.; Chessmore, R. B.

    1985-05-01

    Thorium-232 reference materials with a matrix similar to soil and uranium-mill tailings are necessary for ensuring uniform standardization among measurements performed by remedial-action contractors. Some 200 pounds each of three different concentrations of Th-232 reference material were prepared by diluting a thorium ore with soil. Target values for Th-232 content were 70, 30, and 10 pCi/q. The recommended thorium-232 concentrations for the three reference materials are 71.2 + or - 2.0 pCi/g, 30.5 + or - 0.6 pCi/g, and 10.2 + or - 0.3 pCi/g.

  8. A new river sediment standard reference material.

    PubMed

    Epstein, M S; Diamondstone, B I; Gills, T E

    1989-01-01

    The collection, processing and certification of a new sediment Standard Reference Material (SRM), SRM 2704, is described. Collected from the bottom of the Buffalo River in New York State during the fall of 1986, SRM 2704 is certified for 25 elements with information provided on another 22 elements. Improvements in analytical methods as well as the application of well-defined quality-control procedures for collection, processing and analysis have resulted in a reference material that is more completely characterized than previous NIST sediment reference materials.

  9. Toward a computational psycholinguistics of reference production.

    PubMed

    van Deemter, Kees; Gatt, Albert; van Gompel, Roger P G; Krahmer, Emiel

    2012-04-01

    This article introduces the topic ''Production of Referring Expressions: Bridging the Gap between Computational and Empirical Approaches to Reference'' of the journal Topics in Cognitive Science. We argue that computational and psycholinguistic approaches to reference production can benefit from closer interaction, and that this is likely to result in the construction of algorithms that differ markedly from the ones currently known in the computational literature. We focus particularly on determinism, the feature of existing algorithms that is perhaps most clearly at odds with psycholinguistic results, discussing how future algorithms might include non-determinism, and how new psycholinguistic experiments could inform the development of such algorithms.

  10. TEPC performance for a reference standard.

    PubMed

    Zhang, Weihua; Wang, Zhiqiang; Liu, Yina; Li, Chunjuan; Xiao, Xuefu; Luo, Hailong; Chen, Jun; Li, Wei

    2014-01-01

    A portable tissue-equivalent proportional counter (TEPC)-based system was developed, which will be used as a reference standard in the neutron mixed field for radiation protection. In this paper, microdosimetry of the TEPC system was studied both in neutron ((252)Cf and (241)Am-Be sources) and gamma ((137)Cs and (60)Co sources) reference radiation fields. The measured neutron and gamma-dose equivalent rates were, respectively, compared with those of the reference ambient dose equivalent rate H(*)(10). And the measured microdosimetric spectra were compared with the Monte Carlo code FLUKA simulated results. All of the comparisons primarily agreed well.

  11. Datums, Ellipsoids, Grids, and Grid Reference Systems

    DTIC Science & Technology

    1992-01-01

    Tunisie Grid, Sud Algerie Grid, Sud Maroc Grid, and Sud Tunisie Grid. 4-1.1.8 The...REFERENCES ON THE SUD ALGERIE AND SUD TUNISIE GRIDS 6-8.5.2 When oil reference boxes cannot be accommodated in the margin, the excess is shown in expanses...GIVING REFERENCES ON THE SUD ALGERIE AND SUD TUNISIE GRIDS 6-21 DMA TM 8358.1 I CHAPTER 7 GRIDS ON MAPS AT 1:250,000 AND 1:500,000 SCALE 7.1 GENERAL.

  12. Reference Books in Special Media. Reference Circular No. 82-4.

    ERIC Educational Resources Information Center

    Library of Congress, Washington, DC. National Library Service for the Blind and Physically Handicapped.

    Based on information contained in producers' catalogs and on responses to a survey conducted by the Reference Section of the Library of Congress National Library Service (NLS) for the Blind and Physically Handicapped, this publication lists reference materials produced in braille or in large type, and sound recordings of reference works available…

  13. Genetics Home Reference: short QT syndrome

    MedlinePlus

    ... short QT" refers to a specific pattern of heart activity that is detected with an electrocardiogram (EKG) , which is a test used to measure the electrical activity of the heart. In people with this condition, the part of ...

  14. Selected References and Irish Curios and Cameos.

    ERIC Educational Resources Information Center

    Lapham, Stephen

    2000-01-01

    Provides a bibliography of literature for young adults and selected references on the Great Irish Famine. Presents hints to six riddles of Ireland and includes the answers to the riddles on page 15 of this issue. (CMK)

  15. Genetics Home Reference: Bernard-Soulier syndrome

    MedlinePlus

    ... healthcare professional . About Genetics Home Reference Site Map Customer Support Selection Criteria for Links USA.gov Copyright Privacy Accessibility FOIA Viewers & Players U.S. Department of Health & Human Services National Institutes of Health National Library of Medicine ...

  16. Selected Reference Books of 2000/2001.

    ERIC Educational Resources Information Center

    McIlvaine, Eileen

    2002-01-01

    Presents an annotated list of selected recent scholarly and general reference works under the subject categories of archives; literature; music; psychology; sociology; black studies; women's studies; history and area studies; and new editions and supplements. (LRW)

  17. Genetics Home Reference: fish-eye disease

    MedlinePlus

    ... levels of HDL cholesterol and atherosclerosis, a variable relationship--a review of LCAT deficiency. Vasc Health Risk ... healthcare professional . About Genetics Home Reference Site Map Customer Support Selection Criteria for Links USA.gov Copyright ...

  18. Genetics Home Reference: Y chromosome infertility

    MedlinePlus

    ... deletions" of the human Y chromosome and their relationship with male infertility. J Genet Genomics. 2008 Apr; ... healthcare professional . About Genetics Home Reference Site Map Customer Support Selection Criteria for Links USA.gov Copyright ...

  19. Genetics Home Reference: isolated lissencephaly sequence

    MedlinePlus

    ... LIS1-related isolated lissencephaly: spectrum of mutations and relationships with malformation severity. Arch Neurol. 2009 Aug;66( ... healthcare professional . About Genetics Home Reference Site Map Customer Support Selection Criteria for Links USA.gov Copyright ...

  20. Genetics Home Reference: complete LCAT deficiency

    MedlinePlus

    ... levels of HDL cholesterol and atherosclerosis, a variable relationship--a review of LCAT deficiency. Vasc Health Risk ... healthcare professional . About Genetics Home Reference Site Map Customer Support Selection Criteria for Links USA.gov Copyright ...

  1. Genetics Home Reference: Fukuyama congenital muscular dystrophy

    MedlinePlus

    ... Fujii T, Aiba H, Toda T. Seizure-genotype relationship in Fukuyama-type congenital muscular dystrophy. Brain Dev. ... healthcare professional . About Genetics Home Reference Site Map Customer Support Selection Criteria for Links USA.gov Copyright ...

  2. Genetics Home Reference: neurohypophyseal diabetes insipidus

    MedlinePlus

    ... G, Colao A. Central diabetes insipidus and autoimmunity: relationship between the occurrence of antibodies to arginine vasopressin- ... healthcare professional . About Genetics Home Reference Site Map Customer Support Selection Criteria for Links USA.gov Copyright ...

  3. WWW Search Tools in Reference Services.

    ERIC Educational Resources Information Center

    Kimmel, Stacey

    1997-01-01

    Provides an introduction to World Wide Web search tools for reference services. Discusses characteristics of search services and types of tools available, including search engines/robot-generated databases, directories, metasearch engines, and review/rating sites. (AEF)

  4. 28 CFR 63.3 - References.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Administration DEPARTMENT OF JUSTICE (CONTINUED) FLOODPLAIN MANAGEMENT AND WETLAND PROTECTION PROCEDURES § 63.3 References. (a) Unified National Program for Floodplain Management, Water Resources Council, which is incorporated in these guidelines. (b) Water Resources Council Floodplain Management Guidelines, Water...

  5. 28 CFR 63.3 - References.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Administration DEPARTMENT OF JUSTICE (CONTINUED) FLOODPLAIN MANAGEMENT AND WETLAND PROTECTION PROCEDURES § 63.3 References. (a) Unified National Program for Floodplain Management, Water Resources Council, which is incorporated in these guidelines. (b) Water Resources Council Floodplain Management Guidelines, Water...

  6. 28 CFR 63.3 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Administration DEPARTMENT OF JUSTICE (CONTINUED) FLOODPLAIN MANAGEMENT AND WETLAND PROTECTION PROCEDURES § 63.3 References. (a) Unified National Program for Floodplain Management, Water Resources Council, which is incorporated in these guidelines. (b) Water Resources Council Floodplain Management Guidelines, Water...

  7. 28 CFR 63.3 - References.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Administration DEPARTMENT OF JUSTICE (CONTINUED) FLOODPLAIN MANAGEMENT AND WETLAND PROTECTION PROCEDURES § 63.3 References. (a) Unified National Program for Floodplain Management, Water Resources Council, which is incorporated in these guidelines. (b) Water Resources Council Floodplain Management Guidelines, Water...

  8. 28 CFR 63.3 - References.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Administration DEPARTMENT OF JUSTICE (CONTINUED) FLOODPLAIN MANAGEMENT AND WETLAND PROTECTION PROCEDURES § 63.3 References. (a) Unified National Program for Floodplain Management, Water Resources Council, which is incorporated in these guidelines. (b) Water Resources Council Floodplain Management Guidelines, Water...

  9. Nonparametric spirometry reference values for Hispanic Americans.

    PubMed

    Glenn, Nancy L; Brown, Vanessa M

    2011-02-01

    Recent literature sites ethnic origin as a major factor in developing pulmonary function reference values. Extensive studies established reference values for European and African Americans, but not for Hispanic Americans. The Third National Health and Nutrition Examination Survey defines Hispanic as individuals of Spanish speaking cultures. While no group was excluded from the target population, sample size requirements only allowed inclusion of individuals who identified themselves as Mexican Americans. This research constructs nonparametric reference value confidence intervals for Hispanic American pulmonary function. The method is applicable to all ethnicities. We use empirical likelihood confidence intervals to establish normal ranges for reference values. Its major advantage: it is model free, but shares asymptotic properties of model based methods. Statistical comparisons indicate that empirical likelihood interval lengths are comparable to normal theory intervals. Power and efficiency studies agree with previously published theoretical results.

  10. Reference Device-Assisted Adaptive Location Fingerprinting

    PubMed Central

    Wu, Dongjin; Xia, Linyuan

    2016-01-01

    Location fingerprinting suffers in dynamic environments and needs recalibration from time to time to maintain system performance. This paper proposes an adaptive approach for location fingerprinting. Based on real-time received signal strength indicator (RSSI) samples measured by a group of reference devices, the approach applies a modified Universal Kriging (UK) interpolant to estimate adaptive temporal and environmental radio maps. The modified UK can take the spatial distribution characteristics of RSSI into account. In addition, the issue of device heterogeneity caused by multiple reference devices is further addressed. To compensate the measuring differences of heterogeneous reference devices, differential RSSI metric is employed. Extensive experiments were conducted in an indoor field and the results demonstrate that the proposed approach not only adapts to dynamic environments and the situation of changing APs’ positions, but it is also robust toward measuring differences of heterogeneous reference devices. PMID:27258284

  11. 33 CFR 183.215 - Reference depth.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...) BOATING SAFETY BOATS AND ASSOCIATED EQUIPMENT Flotation Requirements for Outboard Boats Rated for Engines... between the uppermost surface of the submerged reference area of a boat and the surface of the...

  12. 33 CFR 183.315 - Reference depth.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...) BOATING SAFETY BOATS AND ASSOCIATED EQUIPMENT Flotation Requirements for Outboard Boats Rated for Engines... between the uppermost surface of the submerged reference area of a boat and the surface of the...

  13. Identifying reference chemicals for thyroid bioactivity screening.

    PubMed

    Wegner, Susanna; Browne, Patience; Dix, David

    2016-10-01

    Reference chemicals were selected based on thyroid bioactivity in 'Tier 1' screening assays used by the U.S. EPA's Endocrine Disruptor Screening Program. Active reference chemicals had significant effects on thyroid-responsive endpoints in the amphibian metamorphosis assay, and the male and female pubertal rat assays. In the absence of thyroid weight or histopathological effects, additional published studies providing mechanistic data on thyroid activity were required for active chemicals. Inactive reference chemicals had no significant effects on thyroid-responsive endpoints in Tier 1 assays, or in amphibian or rodent studies from several online databases. The 34 reference chemicals (29 active and five inactive) will be useful for performance-based validation of alternative, high throughput screening assays for thyroid bioactivity.

  14. 32 CFR 507.2 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... MANUFACTURE AND SALE OF DECORATIONS, MEDALS, BADGES, INSIGNIA, COMMERCIAL USE OF HERALDIC DESIGNS AND HERALDIC QUALITY CONTROL PROGRAM Introduction § 507.2 References. Related publications are listed in paragraphs...

  15. 32 CFR 865.101 - References.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... PERSONNEL REVIEW BOARDS Air Force Discharge Review Board § 865.101 References. (a) Title 10 U.S.C., section...-0684 (D.D.C.) (Order, December 3, 1981). (k) Urban Law Institute of Antioch College, Inc. v....

  16. 32 CFR 865.101 - References.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... PERSONNEL REVIEW BOARDS Air Force Discharge Review Board § 865.101 References. (a) Title 10 U.S.C., section...-0684 (D.D.C.) (Order, December 3, 1981). (k) Urban Law Institute of Antioch College, Inc. v....

  17. Astronomical catalog desk reference, 1994 edition

    NASA Technical Reports Server (NTRS)

    1994-01-01

    The Astronomical Catalog Desk Reference is designed to aid astronomers in locating machine readable catalogs in the Astronomical Data Center (ADC) archives. The key reference components of this document are as follows: A listing of shortened titles for all catalogs available from the ADC (includes the name of the lead author and year of publication), brief descriptions of over 300 astronomical catalogs, an index of ADC catalog numbers by subject keyword, and an index of ADC catalog numbers by author. The heart of this document is the set of brief descriptions generated by the ADC staff. The 1994 edition of the Astronomical Catalog Desk Reference contains descriptions for over one third of the catalogs in the ADC archives. Readers are encouraged to refer to this section for concise summaries of those catalogs and their contents.

  18. Improved reference models for middle atmosphere ozone

    NASA Astrophysics Data System (ADS)

    Keating, G. M.; Pitts, M. C.; Chen, C.

    This paper describes the improvements introduced into the original version of ozone reference model of Keating and Young (1985, 1987) which is to be incorporated in the next COSPAR International Reference Atmosphere (CIRA). The ozone reference model will provide information on the global ozone distribution (including the ozone vertical structure as a function of month and latitude from 25 to 90 km) combining data from five recent satellite experiments: the Nimbus 7 LIMS, Nimbus 7 SBUV, AE-2 Stratospheric Aerosol Gas Experiment (SAGE), Solar Mesosphere Explorer (SME) UV Spectrometer, and SME 1.27 Micron Airglow. The improved version of the reference model uses reprocessed AE-2 SAGE data (sunset) and extends the use of SAGE data from 1981 to the 1981-1983 time period. Comparisons are presented between the results of this ozone model and various nonsatellite measurements at different levels in the middle atmosphere.

  19. 33 CFR 183.215 - Reference depth.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ...) BOATING SAFETY BOATS AND ASSOCIATED EQUIPMENT Flotation Requirements for Outboard Boats Rated for Engines... between the uppermost surface of the submerged reference area of a boat and the surface of the...

  20. 33 CFR 183.215 - Reference depth.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ...) BOATING SAFETY BOATS AND ASSOCIATED EQUIPMENT Flotation Requirements for Outboard Boats Rated for Engines... between the uppermost surface of the submerged reference area of a boat and the surface of the...

  1. 33 CFR 183.315 - Reference depth.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ...) BOATING SAFETY BOATS AND ASSOCIATED EQUIPMENT Flotation Requirements for Outboard Boats Rated for Engines... between the uppermost surface of the submerged reference area of a boat and the surface of the...

  2. 33 CFR 183.315 - Reference depth.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ...) BOATING SAFETY BOATS AND ASSOCIATED EQUIPMENT Flotation Requirements for Outboard Boats Rated for Engines... between the uppermost surface of the submerged reference area of a boat and the surface of the...

  3. Recommended reference figures for geophysics and geodesy

    NASA Technical Reports Server (NTRS)

    Khan, M. A.; Okeefe, J. A.

    1973-01-01

    Specific reference figures are recommended for consistent use in geophysics and geodesy. The selection of appropriate reference figure for geophysical studies suggests a relationship between the Antarctic negative gravity anomaly and the great shrinkage of the Antarctic ice cap about 4-5 million years ago. The depression of the south polar regions relative to the north polar regions makes the Southern Hemisphere flatter than the Northern Hemisphere, thus producing the third harmonic (pear-shaped) contribution to the earth's figure.

  4. On Fractional Model Reference Adaptive Control

    PubMed Central

    Shi, Bao; Dong, Chao

    2014-01-01

    This paper extends the conventional Model Reference Adaptive Control systems to fractional ones based on the theory of fractional calculus. A control law and an incommensurate fractional adaptation law are designed for the fractional plant and the fractional reference model. The stability and tracking convergence are analyzed using the frequency distributed fractional integrator model and Lyapunov theory. Moreover, numerical simulations of both linear and nonlinear systems are performed to exhibit the viability and effectiveness of the proposed methodology. PMID:24574897

  5. Automated Coastal Engineering System: Technical Reference

    DTIC Science & Technology

    1992-09-01

    m··’· I .·. l ’j, :II . ,II fTJ11 ~ AUTOMATED COASTAL ENGINEERING SYSTEM TECHNICAL REFERENCE by David A. Leenknecht, Andre Szuwalski and Ann...Vicksburg, Mississippi 39180-6199 Version 1.07 September 1992 HECSA TECHNICAL LIBRARY Report Documentation Page Form ApprovedOMB No. 0704-0188 Public...1992 4. TITLE AND SUBTITLE Automated Coastal Engineering System: Technical Reference 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT

  6. Developing an Agent Systems Reference Architecture

    DTIC Science & Technology

    2010-05-01

    The notion of a reference architecture has different meanings based on the view- points and concerns of the stakeholders. In this work, a reference...functional concept defined by the ASRM and further elaborating actors and invoca- tion points . The intended audience are high-level practitioners who need...execution. Figure 1(a) displays the temporal view of a scenario demonstrating the invocation points of the agent mobility functional con- cept. The

  7. Global Positioning System Shipborne Reference System

    DTIC Science & Technology

    1997-09-30

    Office of Naval Research Space and Remote Sensing 1997 Annual Report 1 GLOBAL POSITIONING SYSTEM SHIPBORNE REFERENCE SYSTEM James R. Clynch...N00014-97-WR30044 LONG-TERM GOAL The long term goal is to improve the navigation capability of naval vessels using the Global Positioning System ...COVERED 00-00-1997 to 00-00-1997 4. TITLE AND SUBTITLE Global Positioning System Shipborne Reference System 5a. CONTRACT NUMBER 5b. GRANT

  8. Building complex reference objects from dual sets

    PubMed Central

    Patson, Nikole D.; Warren, Tessa

    2011-01-01

    There has been considerable psycholinguistic investigation into the conditions that allow separately introduced individuals to be joined into a plural set and represented as a complex reference object (e.g., Eschenbach, et al., 1989; Garrod & Sanford, 1982; Koh & Clifton, 2002; Koh et al., 2008; Moxey et al., 2004; Sanford & Lockhart, 1990). The current paper reports three eye-tracking experiments that investigate the less-well understood question of what conditions allow pointers to be assigned to the individuals within a previously undifferentiated set, turning it into a complex reference object. The experiments made use of a methodology used in Patson and Ferreira (2009) to distinguish between complex reference objects and undifferentiated sets. Experiments 1 and 2 demonstrated that assigning different properties to the members of an undifferentiated dual set via a conjoined modifier or a comparative modifier transformed it into a complex reference object. Experiment 3 indicated that assigning a property to only one member of an undifferentiated dual set introduced pointers to both members. These results demonstrate that pointers can be established to referents within a plural set without picking them out via anaphors; they set boundaries on the kinds of implicit contrasts between referents that establish pointers; and they illustrate that extremely subtle properties of the semantic and referential context can affect early parsing decisions. PMID:21666836

  9. Analysis of SOFCs Using Reference Electrodes

    SciTech Connect

    Finklea, H.; Chen, X.; Gerdes, K.; Pakalapati, S.; Celik, I.

    2013-01-01

    Reference electrodes are frequently applied to isolate the performance of one electrode in a solid oxide fuel cell. However, reference electrode simulations raise doubt to veracity of data collected using reference electrodes. The simulations predict that the reported performance for the one electrode will frequently contain performance of both electrodes. Nonetheless, recent reports persistently treat data so collected as ideally isolated. This work confirms the predictions of the reference electrode simulations on two SOFC designs, and to provides a method of validating the data measured in the 3-electrode configuration. Validation is based on the assumption that a change in gas composition to one electrode does not affect the impedance of the other electrode at open circuit voltage. This assumption is supported by a full physics simulation of the SOFC. Three configurations of reference electrode and cell design are experimentally examined using various gas flows and two temperatures. Impedance data are subjected to deconvolution analysis and equivalent circuit fitting and approximate polarization resistances of the cathode and anode are determined. The results demonstrate that the utility of reference electrodes is limited and often wholly inappropriate. Reported impedances and single electrode polarization values must be scrutinized on this basis.

  10. An ethnically relevant consensus Korean reference genome is a step towards personal reference genomes

    PubMed Central

    Cho, Yun Sung; Kim, Hyunho; Kim, Hak-Min; Jho, Sungwoong; Jun, JeHoon; Lee, Yong Joo; Chae, Kyun Shik; Kim, Chang Geun; Kim, Sangsoo; Eriksson, Anders; Edwards, Jeremy S.; Lee, Semin; Kim, Byung Chul; Manica, Andrea; Oh, Tae-Kwang; Church, George M.; Bhak, Jong

    2016-01-01

    Human genomes are routinely compared against a universal reference. However, this strategy could miss population-specific and personal genomic variations, which may be detected more efficiently using an ethnically relevant or personal reference. Here we report a hybrid assembly of a Korean reference genome (KOREF) for constructing personal and ethnic references by combining sequencing and mapping methods. We also build its consensus variome reference, providing information on millions of variants from 40 additional ethnically homogeneous genomes from the Korean Personal Genome Project. We find that the ethnically relevant consensus reference can be beneficial for efficient variant detection. Systematic comparison of human assemblies shows the importance of assembly quality, suggesting the necessity of new technologies to comprehensively map ethnic and personal genomic structure variations. In the era of large-scale population genome projects, the leveraging of ethnicity-specific genome assemblies as well as the human reference genome will accelerate mapping all human genome diversity. PMID:27882922

  11. An ethnically relevant consensus Korean reference genome is a step towards personal reference genomes.

    PubMed

    Cho, Yun Sung; Kim, Hyunho; Kim, Hak-Min; Jho, Sungwoong; Jun, JeHoon; Lee, Yong Joo; Chae, Kyun Shik; Kim, Chang Geun; Kim, Sangsoo; Eriksson, Anders; Edwards, Jeremy S; Lee, Semin; Kim, Byung Chul; Manica, Andrea; Oh, Tae-Kwang; Church, George M; Bhak, Jong

    2016-11-24

    Human genomes are routinely compared against a universal reference. However, this strategy could miss population-specific and personal genomic variations, which may be detected more efficiently using an ethnically relevant or personal reference. Here we report a hybrid assembly of a Korean reference genome (KOREF) for constructing personal and ethnic references by combining sequencing and mapping methods. We also build its consensus variome reference, providing information on millions of variants from 40 additional ethnically homogeneous genomes from the Korean Personal Genome Project. We find that the ethnically relevant consensus reference can be beneficial for efficient variant detection. Systematic comparison of human assemblies shows the importance of assembly quality, suggesting the necessity of new technologies to comprehensively map ethnic and personal genomic structure variations. In the era of large-scale population genome projects, the leveraging of ethnicity-specific genome assemblies as well as the human reference genome will accelerate mapping all human genome diversity.

  12. Myths of Isotopic Reference Materials Busted

    NASA Astrophysics Data System (ADS)

    Coplen, T.

    2007-12-01

    During the past several years, the determination of the isotopic abundances of elements including H, Li, B, C, N, O, Mg, Si, S, Cl, Ca, Cr, Fe, Cu, Zn, Tl, and Se has substantially increased because of expanded use in hydrology, environmental studies, microbiology, forensic investigations, atmospheric investigations, oceanography, etc. Improvements in instrumentation enable increasingly precise isotope-amount-ratio measurements in these fields, but these improvements in precision commonly do not lead to improvements in accuracy because of the lack or improper use of isotopic reference materials. When properly used, these critically important materials enable any laboratory worldwide to measure the same homogeneous sample and report the same isotopic abundance within analytical uncertainty. For example, for stable isotopic analysis of gaseous hydrogen samples, the agreement among 36 laboratories worldwide before normalization to any hydrogen gas reference material was 11.8 per mill. After normalization to anchors (gaseous H isotopic reference materials) at each end of the delta H-2 scale, the agreement was 0.85 per mill, an improvement of more than an order of magnitude. Consistency of delta C-13 measurements often can be improved by nearly 50 percent by anchoring the delta C-13 scale with two isotopic reference materials differing substantially in C-13 mole fraction, namely NBS 19 calcite and L-SVEC lithium carbonate. Agreement of delta C-13 values of four expert laboratories analyzing USGS40 L- glutamic acid by CF-IRMS methods improved from 0.084 to 0.015 per mill with use of the two scale anchors (NBS 19 and L-SVEC). Solid oxygen isotopic reference materials (IAEA-600 caffeine, IAEA-601 and IAEA-602 benzoic acids, IAEA-NO-3, USGS32, USGS34, and USGS35 nitrates, NBS-127, IAEA-SO-5, and IAEA-SO-6 barium sulfates) are poorly calibrated. Calibrating these solids to the VSMOW-SLAP reference water scale has been very difficult because both the solids and reference

  13. Global daily reference evapotranspiration modeling and evaluation

    USGS Publications Warehouse

    Senay, G.B.; Verdin, J.P.; Lietzow, R.; Melesse, Assefa M.

    2008-01-01

    Accurate and reliable evapotranspiration (ET) datasets are crucial in regional water and energy balance studies. Due to the complex instrumentation requirements, actual ET values are generally estimated from reference ET values by adjustment factors using coefficients for water stress and vegetation conditions, commonly referred to as crop coefficients. Until recently, the modeling of reference ET has been solely based on important weather variables collected from weather stations that are generally located in selected agro-climatic locations. Since 2001, the National Oceanic and Atmospheric Administration’s Global Data Assimilation System (GDAS) has been producing six-hourly climate parameter datasets that are used to calculate daily reference ET for the whole globe at 1-degree spatial resolution. The U.S. Geological Survey Center for Earth Resources Observation and Science has been producing daily reference ET (ETo) since 2001, and it has been used on a variety of operational hydrological models for drought and streamflow monitoring all over the world. With the increasing availability of local station-based reference ET estimates, we evaluated the GDAS-based reference ET estimates using data from the California Irrigation Management Information System (CIMIS). Daily CIMIS reference ET estimates from 85 stations were compared with GDAS-based reference ET at different spatial and temporal scales using five-year daily data from 2002 through 2006. Despite the large difference in spatial scale (point vs. ∼100 km grid cell) between the two datasets, the correlations between station-based ET and GDAS-ET were very high, exceeding 0.97 on a daily basis to more than 0.99 on time scales of more than 10 days. Both the temporal and spatial correspondences in trend/pattern and magnitudes between the two datasets were satisfactory, suggesting the reliability of using GDAS parameter-based reference ET for regional water and energy balance studies in many parts of the world

  14. [Diagnostic reference levels in interventional radiology].

    PubMed

    Vañó Carruana, E; Fernández Soto, J M; Sánchez Casanueva, R M; Ten Morón, J I

    2013-12-01

    This article discusses the diagnostic reference levels for radiation exposure proposed by the International Commission on Radiological Protection (ICRP) to facilitate the application of the optimization criteria in diagnostic imaging and interventional procedures. These levels are normally established as the third quartile of the dose distributions to patients in an ample sample of centers and are supposed to be representative of good practice regarding patient exposure. In determining these levels, it is important to evaluate image quality as well to ensure that it is sufficient for diagnostic purposes. When the values for the dose received by patients are systematically higher or much lower than the reference levels, an investigation should determine whether corrective measures need to be applied. The European and Spanish regulations require the use of these reference values in quality assurance programs. For interventional procedures, the dose area product (or kerma area product) values are usually used as reference values together with the time under fluoroscopy and the total number of images acquired. The most modern imaging devices allow the value of the accumulated dose at the entrance to the patient to be calculated to optimize the distribution of the dose on the skin. The ICRP recommends that the complexity of interventional procedures be taken into account when establishing reference levels. In the future, diagnostic imaging departments will have automatic systems to manage patient dosimetric data; these systems will enable continuous dosage auditing and alerts about individual procedures that might involve doses several times above the reference values. This article also discusses aspects that need to be clarified to take better advantage of the reference levels in interventional procedures.

  15. With Reference to Reference Genes: A Systematic Review of Endogenous Controls in Gene Expression Studies

    PubMed Central

    Chapman, Joanne R.; Waldenström, Jonas

    2015-01-01

    The choice of reference genes that are stably expressed amongst treatment groups is a crucial step in real-time quantitative PCR gene expression studies. Recent guidelines have specified that a minimum of two validated reference genes should be used for normalisation. However, a quantitative review of the literature showed that the average number of reference genes used across all studies was 1.2. Thus, the vast majority of studies continue to use a single gene, with β-actin (ACTB) and/or glyceraldehyde 3-phosphate dehydrogenase (GAPDH) being commonly selected in studies of vertebrate gene expression. Few studies (15%) tested a panel of potential reference genes for stability of expression before using them to normalise data. Amongst studies specifically testing reference gene stability, few found ACTB or GAPDH to be optimal, whereby these genes were significantly less likely to be chosen when larger panels of potential reference genes were screened. Fewer reference genes were tested for stability in non-model organisms, presumably owing to a dearth of available primers in less well characterised species. Furthermore, the experimental conditions under which real-time quantitative PCR analyses were conducted had a large influence on the choice of reference genes, whereby different studies of rat brain tissue showed different reference genes to be the most stable. These results highlight the importance of validating the choice of normalising reference genes before conducting gene expression studies. PMID:26555275

  16. With Reference to Reference Genes: A Systematic Review of Endogenous Controls in Gene Expression Studies.

    PubMed

    Chapman, Joanne R; Waldenström, Jonas

    2015-01-01

    The choice of reference genes that are stably expressed amongst treatment groups is a crucial step in real-time quantitative PCR gene expression studies. Recent guidelines have specified that a minimum of two validated reference genes should be used for normalisation. However, a quantitative review of the literature showed that the average number of reference genes used across all studies was 1.2. Thus, the vast majority of studies continue to use a single gene, with β-actin (ACTB) and/or glyceraldehyde 3-phosphate dehydrogenase (GAPDH) being commonly selected in studies of vertebrate gene expression. Few studies (15%) tested a panel of potential reference genes for stability of expression before using them to normalise data. Amongst studies specifically testing reference gene stability, few found ACTB or GAPDH to be optimal, whereby these genes were significantly less likely to be chosen when larger panels of potential reference genes were screened. Fewer reference genes were tested for stability in non-model organisms, presumably owing to a dearth of available primers in less well characterised species. Furthermore, the experimental conditions under which real-time quantitative PCR analyses were conducted had a large influence on the choice of reference genes, whereby different studies of rat brain tissue showed different reference genes to be the most stable. These results highlight the importance of validating the choice of normalising reference genes before conducting gene expression studies.

  17. Physics of Non-Inertial Reference Frames

    SciTech Connect

    Kamalov, Timur F.

    2010-12-22

    Physics of non-inertial reference frames is a generalizing of Newton's laws to any reference frames. It is the system of general axioms for classical and quantum mechanics. The first, Kinematics Principle reads: the kinematic state of a body free of forces conserves and equal in absolute value to an invariant of the observer's reference frame. The second, Dynamics Principle extended Newton's second law to non-inertial reference frames and also contains additional variables there are higher derivatives of coordinates. Dynamics Principle reads: a force induces a change in the kinematic state of the body and is proportional to the rate of its change. It is mean that if the kinematic invariant of the reference frame is n-th derivative with respect the time, then the dynamics of a body being affected by the force F is described by the 2n-th differential equation. The third, Statics Principle reads: the sum of all forces acting a body at rest is equal to zero.

  18. Genotype Imputation with Millions of Reference Samples.

    PubMed

    Browning, Brian L; Browning, Sharon R

    2016-01-07

    We present a genotype imputation method that scales to millions of reference samples. The imputation method, based on the Li and Stephens model and implemented in Beagle v.4.1, is parallelized and memory efficient, making it well suited to multi-core computer processors. It achieves fast, accurate, and memory-efficient genotype imputation by restricting the probability model to markers that are genotyped in the target samples and by performing linear interpolation to impute ungenotyped variants. We compare Beagle v.4.1 with Impute2 and Minimac3 by using 1000 Genomes Project data, UK10K Project data, and simulated data. All three methods have similar accuracy but different memory requirements and different computation times. When imputing 10 Mb of sequence data from 50,000 reference samples, Beagle's throughput was more than 100× greater than Impute2's throughput on our computer servers. When imputing 10 Mb of sequence data from 200,000 reference samples in VCF format, Minimac3 consumed 26× more memory per computational thread and 15× more CPU time than Beagle. We demonstrate that Beagle v.4.1 scales to much larger reference panels by performing imputation from a simulated reference panel having 5 million samples and a mean marker density of one marker per four base pairs.

  19. Automatic no-reference image quality assessment.

    PubMed

    Li, Hongjun; Hu, Wei; Xu, Zi-Neng

    2016-01-01

    No-reference image quality assessment aims to predict the visual quality of distorted images without examining the original image as a reference. Most no-reference image quality metrics which have been already proposed are designed for one or a set of predefined specific distortion types and are unlikely to generalize for evaluating images degraded with other types of distortion. There is a strong need of no-reference image quality assessment methods which are applicable to various distortions. In this paper, the authors proposed a no-reference image quality assessment method based on a natural image statistic model in the wavelet transform domain. A generalized Gaussian density model is employed to summarize the marginal distribution of wavelet coefficients of the test images, so that correlative parameters are needed for the evaluation of image quality. The proposed algorithm is tested on three large-scale benchmark databases. Experimental results demonstrate that the proposed algorithm is easy to implement and computational efficient. Furthermore, our method can be applied to many well-known types of image distortions, and achieves a good quality of prediction performance.

  20. NASA CEV Reference GN&C Architecture

    NASA Technical Reports Server (NTRS)

    Tamblyn, Scott; Hinkel, Heather; Saley, Dave

    2007-01-01

    The Orion Crew Exploration Vehicle (CEV) will be the first human spacecraft built by NASA in almost 3 decades and will be the first vehicle to perform both Low Earth Orbit (LEO) missions and lunar missions since Apollo. The awesome challenge of designing a Guidance, Navigation, and Control (GN&C) system for this vehicle that satisfies all of its various mission requirements is countered by the opportunity to take advantage of the improvements in algorithms, software, sensors, and other related GN&C technology over this period. This paper describes the CEV GN&C reference architecture developed to support the overall NASA reference configuration and validate the driving requirements of the Constellation (Cx) Architecture Requirements Document (CARD, Reference 1) and the CEV System Requirements Document (SRD, Reference 2). The Orion GN&C team designed the reference architecture based on the functional allocation of GN&C roles and responsibilities of CEV with respect to the other Cx vehicles, such as the Crew Launch Vehicle (CLV), Earth Departure Stage (EDS), and Lunar Surface Area Module (LSAM), across all flight phases. The specific challenges and responsibilities of the CEV GN&C system from launch pad to touchdown will be introduced along with an overview of the navigation sensor suite, its redundancy management, and flight software (FSW) architecture. Sensors will be discussed in terms of range of operation, data utility within the navigation system, and rationale for selection. The software architecture is illustrated via block diagrams, commensurate with the design aspects.

  1. Alcohol References on Undergraduate Males’ Facebook Profiles

    PubMed Central

    Egan, Katie G.; Moreno, Megan A.

    2011-01-01

    Perceived peer alcohol use is a predictor of consumption in college males; frequent references to alcohol on Facebook may encourage alcohol consumption. Content analysis of college males’ Facebook profiles identified references to alcohol. The average age of 225 identified profiles was 19.9 years. Alcohol references were present on 85.3% of the profiles; the prevalence of alcohol was similar across each undergraduate grade. The average number of alcohol references per profile was 8.5 but increased with undergraduate year (p = .003; confidence interval = 1.5, 7.5). Students who were of legal drinking age referenced alcohol 4.5 times more than underage students, and an increase in number of Facebook friends was associated with an increase in displayed alcohol references (p < .001; confidence interval = 0.009, 0.02). Facebook is widely used in the college population; widespread alcohol displays on Facebook may influence social norms and cause increases in male college students’ alcohol use. PMID:21406490

  2. Performance evaluation of pumping systems used in commercial-scale, split-pond aquaculture

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Split-pond aquaculture systems have been adopted widely by United States catfish farmers as a way to improve production performance. The split-pond consists of a fish-culture basin that is connected to a waste-treatment lagoon by two water conveyance structures. Water is circulated between the two b...

  3. Process Development of Adenoviral Vector Production in Fixed Bed Bioreactor: From Bench to Commercial Scale.

    PubMed

    Lesch, Hanna P; Heikkilä, Kati M; Lipponen, Eevi M; Valonen, Piia; Müller, Achim; Räsänen, Eva; Tuunanen, Tarja; Hassinen, Minna M; Parker, Nigel; Karhinen, Minna; Shaw, Robert; Ylä-Herttuala, Seppo

    2015-08-01

    Large-scale vector manufacturing for phase III and beyond has proven to be challenging. Upscaling the process with suspension cells is increasingly feasible, but many viral production applications are still applicable only in adherent settings. Scaling up the adherent system has proven to be troublesome. The iCELLis(®) disposable fixed-bed bioreactors offer a possible option for viral vector manufacturing in large quantities in an adherent environment. In this study, we have optimized adenovirus serotype 5 manufacturing using iCELLis Nano with a cultivation area up to 4 m(2). HEK293 cell cultivation, infection, and harvest of the virus (by lysing the cells inside the bioreactor) proved possible, reaching total yield of up to 1.6×10(14) viral particles (vp)/batch. The iCELLis 500 is designed to satisfy demand for large-scale requirements. Inoculating a large quantity of cell mass into the iCELLis 500 was achieved by first expanding the cell mass in suspension. Upscaling the process into an iCELLis 500/100 m(2) cultivation area cassette was practical and produced up to 6.1×10(15) vp. Flask productivity per cm(2) in iCELLis Nano and iCELLis 500 was in the same range. As a conclusion, we showed for the first time that iCELLis 500 equipment has provided an effective way to manufacture large batches of adenoviral vectors.

  4. Commercial-Scale Demonstration of the Liquid Phase Methanol (LPMEOH) Process

    SciTech Connect

    1998-12-21

    The Liquid Phase Methanol (LPMEOW) Demonstration Project at Kingsport Tennessee, is a $213.7 million cooperative agreement between the U.S. Department of Energy (DOE) and Air Products Liquid Phase Conversion Company, L.P. (the Partnership) to produce methanol from coal-derived synthesis gas (syngas). Air Products and Chemicals, Inc. (Air Products) and Eastman Chemical Company (Eastman) formed the Partnership to execute the Demonstration Project. The LPMEOW Process Demonstration Unit was built at a site located at the Eastman complex in Kingsport. During this quarter, initial planning and procurement work began on the seven project sites which have been accepted for participation in the off-site, methanol product-use test plan. Two of the projects have begun pre-testing of equipment and three other projects have commenced with equipment procurement, Methanol produced from carbon monoxide (CO)- rich syngas at the Alternative Fuels Development Unit (AFDU) in LaPorte, TX has been shipped to four of the project sites in anticipation of the start of testing during the first quarter of calendar year 1998. Catalyst activity, as defined by the ratio of the rate constant at any point in time to the rate constant for a freshly reduced catalyst (as determined in the laboratory autoclave), continued to decline more rapidly than expected. In response to concentrations of arsenic and sulfbr detected on catalyst samples from the LPMEOW Reactor, Eastman replaced both the arsine- and sulfiwremoval material in the Eastman guard bed which treats the primary syngas feed stream (&danced Gas) prior to its introduction into both the Eastman fixed-bed methanol plant and the LPMEOWM Demonstration Unit. After restarting the demonstration unit, the catalyst deactivation rate remained essentially unchanged. Parallel testing in the laboratory using arsine-doped, and subsequently arsine- and SuIfi-doped syngas, ako ftiIed to prove that arsine was responsible for the higher-than-expected rate of catalyst deactivation in the demonstration unit. Based on the results of plant operation and catalyst sampling, DOE accepted a recommendation by Air Products and Eastman to drain the initial charge of catalyst from the reactor and replace the charge with fresh catalyst. Prior to this catalyst turnaround, a final test was performed to determine the impact of raising the operating temperature of the LPMEOW Reactor from 250"C to 260oC. carbon. Activation of the new flesh charge of catalyst began on 13 November 1997. Just as in the original start-up in April of 1997, only a partial charge of catalyst (20,700 pounds) was activated to limit the amount of material exposed to poisons at the outset. An attempted restart of the LPMEOW Demonstration Unit on 26 November 1997 was unsuccessfid; settling of the flesh catalyst appeared to have occurred in the LPMEOFP Reactor and gas inlet piping, which resulted in the plugging of the gas sparger at the bottom of the vessel.

  5. Comparing Denitrification Rates and Carbon Sources in Commercial Scale Upflow Denitrification Biological Filters in Aquaculture

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Aerobic biological filtration systems employing nitrifying bacteria to remediate excess ammonia and nitrite concentrations are common components of recirculating aquaculture systems (RAS). However, significant water exchange may still be necessary to reduce nitrate concentrations to acceptable leve...

  6. High Performance Computing: Jet Penetration into a Commercial Scale Transport Gasifier

    SciTech Connect

    Syamlal, M; Guenther, Chris; Gel, Aytekin; Pannala, Sreekanth

    2010-05-01

    The time-averaged information from a 10-million-cell multiphase computational fluid dynamic simulation of a coal gasifier was used as the inlet boundary condition for fine grid simulations of the region near the coal inlet. The simulation results show a distinct coal jet region, characterized by high void fraction and low solids temperature. The jets from right and left inlets have different behaviors caused by the asymmetry in the inlet to the gasifier. The medium grid resolution with a high order discretization scheme offers better jet resolution at lower computational cost than a fine grid with a low order discretization scheme.

  7. Impact of disk milling on corn stover pretreated at commercial scale.

    PubMed

    Kim, Sun Min; Tumbleson, M E; Rausch, Kent D; Singh, Vijay

    2017-05-01

    In cellulosic biofuel production, chemical pretreatment performed at laboratory or pilot scale, followed by mechanical refining, has been demonstrated to be effective to increase feedstock enzyme digestibility. To take the combined pretreatment process one step closer to commercialization, disk milling was performed with commercially pretreated corn stover. Dilute acid pretreated samples with combined severity factors (cSF) of 0.09 (DA09) and 0.43 (DA43) were obtained from a commercial plant. Effects of pretreatment conditions (DA09 and DA43), milling cycles (0, 3, 9, and 15) and enzyme dosages (7.8, 15.6 and 31.2mgcellulase/g dry biomass) were evaluated. Milling improved glucose yields by 0.7 to 1.2-fold. Higher enzyme dosages enhanced sugar yields. Milling was more effective to improve glucose yields, while enzyme dosage was more effective to improve xylose yields. However, dilute acid pretreatment condition was the most important factor to increase final sugar yields compared to milling cycles and enzyme dosages.

  8. Development and testing of commercial-scale, coal-fired combustion systems, Phase 3

    SciTech Connect

    Not Available

    1990-01-01

    The US Department of Energy's Pittsburgh Energy Technology Center (PETC) is actively pursuing the development and testing of coal-fired combustion systems for residential, commercial, and industrial market sectors. In response, MTCI initiated the development of a new combustor technology based on the principle of pulse combustion under the sponsorship of PETC (Contract No. AC22-83PC60419). The initial pulse combustor development program was conducted in three phases (MTCI, Development of a Pulsed Coal Combustor Fired with CWM, Phase III Final Report, DOE Contract No. AC22-83PC60419, November 1986). Phase I included a review of the prior art in the area of pulse combustion and the development of pulse combustor design concepts. It led to the conclusion that pulse combustors offer technical and base-of-operation advantages over conventional burners and also indicated favorable economics for replacement of oil- and gas-fired equipment.

  9. 77 FR 3459 - Cancellation of the Environmental Impact Statement for the Mountaineer Commercial Scale Carbon...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-01-24

    ... Energy's (DOE) Office of Fossil Energy is cancelling the environmental impact statement (EIS) under the... (202) 586-7031. SUPPLEMENTARY INFORMATION: The DOE's Office of Fossil Energy is cancelling the EIS for... Laboratory, Office of Fossil Energy. [FR Doc. 2012-1351 Filed 1-23-12; 8:45 am] BILLING CODE 6450-01-P...

  10. Commercial-Scale Demonstration of the Liquid Phase Methanol (LPMEOTH) Process

    SciTech Connect

    1998-12-21

    The Liquid Phase Methanol (LPMEOW) Demonstration Project at Kingsport, Tennessee, is a $213.7 million cooperative agreement between the U.S. Department of Energy (DOE) and Air Products Liquid Phase Conversion Company, L.P. (the Partnership) to produce methanol from coal-derived synthesis gas (syngas). Air Products and Chemicals, Inc. (Air Products) and Eastman Chemical Company (Eastman) formed the Partnership to execute the Demonstration Project. The LPMEOI-P Process Demonstration Unit was built at a site located at the Eastman coal-to-chemicals complex in Kingsport. During this quarter, initial planning and procurement work continued on the seven project sites which have been accepted for participation in the off-site, product-use test program. Approximately 12,000 gallons of fuel-grade methanol (98+ wt% methanol, 4 wt% water) produced during operation on carbon monoxide (CO)-rich syngas at the LPMEOW Demonstration Unit was loaded into trailers and shipped off-site for Mure product-use testing. At one of the projects, three buses have been tested on chemical-grade methanol and on fhel-grade methanol from the LPMEOW Demonstration Project. During the reporting period, planning for a proof-of-concept test run of the Liquid Phase Dimethyl Ether (LPDME~ Process at the Alternative Fuels Development Unit (AFDU) in LaPorte, TX continued. The commercial catalyst manufacturer (Calsicat) has prepared the first batch of dehydration catalyst in large-scale equipment. Air Products will test a sample of this material in the laboratory autoclave. Catalyst activity, as defined by the ratio of the rate constant at any point in time to the rate constant for freshly reduced catalyst (as determined in the laborato~ autoclave), was monitored for the initial extended operation at the lower initial reactor operating temperature of 235oC. At this condition, the decrease in catalyst activity with time from the period 20 December 1997 through 27 January 1998 occurred at a rate of 1.0% per day, which represented a significant improvement over the 3.4Yi per day decline measured during the initial six weeks of operation in April and May of 1997. The deactivation rate also improved from the longer-term rate of 1.6% per day calculated throughout the summer and autumn of 1997.

  11. Chemistry for commercial scale production of yttrium-90 for medical research.

    PubMed

    Wike, J S; Guyer, C E; Ramey, D W; Phillips, B P

    1990-01-01

    Studies were initiated at Oak Ridge National Laboratory (ORNL) in 1982 for the radiolabeling of resin microspheres with yttrium-90 (90Y) for liver cancer therapy. Yttrium-90 is the decay product of strontium-90 (90Sr). Subsequently, 90Y became a major radioisotope of choice for labeling antibodies for therapeutic trials in the treatment of other forms of cancer. A 25-Ci 90Y 90Y generator or 90Sr cow was placed in service to supply the anticipated needs of customers. In vivo use of 90Y required that the 90Sr contamination levels be kept below 10 muCi/Ci 90Y (corrected to preparation time). Also, it was necessary to remove trace metals that interfered in the 90Y antibody radiolabeling process, giving low radiolabeling yields. Di-(2-ethylhexyl) phosphoric acid (HDEHP) in dodecane has been used routinely at ORNL to extract 90Y and thereby give a product that meets the radiochemical purity required with respect to 90Sr. Methods were also developed to remove interfering trace elements to provide acceptable labeling yields.

  12. Commercial scale cucumber fermentations brined with calcium chloride instead of sodium chloride

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Development of low salt cucumber fermentation processes present opportunities to reduce the amount of sodium chloride (NaCl) that reaches fresh water streams from industrial activities. The objective of this research was to translate cucumber fermentation brined with calcium chloride instead of NaCl...

  13. Environmental siting suitability analysis for commercial scale ocean renewable energy: A southeast Florida case study

    NASA Astrophysics Data System (ADS)

    Mulcan, Amanda

    This thesis aims to facilitate the siting and implementation of Florida Atlantic University Southeast National Marine Renewable Energy Center (FAU SNMREC) ocean current energy (OCE) projects offshore southeastern Florida through the analysis of benthic anchoring conditions. Specifically, a suitability analysis considering all presently available biologic and geologic datasets within the legal framework of OCE policy and regulation was done. OCE related literature sources were consulted to assign suitability levels to each dataset, ArcGIS interpolations generated seafloor substrate maps, and existing submarine cable pathways were considered for OCE power cables. The finalized suitability map highlights the eastern study area as most suitable for OCE siting due to its abundance of sand/sediment substrate, existing underwater cable route access, and minimal biologic presence. Higher resolution datasets are necessary to locate specific OCE development locales, better understand their benthic conditions, and minimize potentially negative OCE environmental impacts.

  14. Commercial-Scale Demonstration of the Liquid Phase Methanol (LPMEOH(TM)) Process

    SciTech Connect

    1997-09-30

    The Liquid Phase Methanol (LPMEOHT") demonstration project at Kingsport, Tennessee, is a $213.7 million cooperative agreement between the U.S. Department of Energy (DOE) and Air Products Liquid Phase Conversion Company, L. P. (the Partnership). Air Products and Chemicals, Inc. (Air Products) and Eastman Chemical Company (Eastman) formed the Partnership to execute the Demonstration Project. A demonstration unit producing 80,000 gallons per day (260 tons-per-day) of methanol from coal-derived synthesis gas (syngas) was designed, constructed, and is operating at a site located at the Eastman complex in Kingsport. The Partnership will own and operate the facility for the four-year demonstration period. This project is sponsored under the DOE's Clean Coal Technology Program, and its primary objective is to "demonstrate the production of methanol using the LPMEOWM Process in conjunction with an integrated coal gasification facility." The project will also demonstrate the suitability of the methanol produced for use as a chemical feedstock or as a low-sulfur dioxide, low-nitrogen oxides alternative fiel in stationary and transportation applications. The project may also demonstrate the production of dimethyl ether (DME) as a mixed coproduct with methanol, if laboratory- and pilot-scale research and market verification studies show promising results. If implemented, the DME would be produced during the last six months of the four-year demonstration period. The LPMEOITM process is the product of a cooperative development effort by Air Products and the DOE in a program that started in 1981. It was successfdly piloted at a 10 tons-per- day (TPD) rate in the DOE-owned experimental unit at Air Products' LaPorte, Texas, site. This demonstration project is the culmination of that extensive cooperative development effort.

  15. Commercial-Scale Demonstration of the Liquid Phase Methanol (LPMEOH) Process

    SciTech Connect

    1998-12-21

    he Liquid Phase Methanol (LPMEOW) Demonstration Project at Kingsport Tennessee, is a $213.7 million cooperative agreement between the U.S. Department of Energy (DOE) and Air Products Liquid Phase Conversion Company, L.P. (the Partnership) to produce methanol from coal-derived synthesis gas (syngas). Air Products and Chemicals, Inc. (Air Products) and Eastman Chemical Company (Eastman) formed the Partnership to execute the Demonstration Project. The LPMEOEP Process Demonstration Unit was built at a site located at the Eastman coal-to-chemicals complex in Kingsport. The LPMEOHW Demonstration Facility completed its first year of operation on 02 April 1998. The LPMEOW Demonstration Facility also completed the longest continuous operating run (65 days) on 21 April 1998. Catalyst activity, as defined by the ratio of the rate constant at any point in time to the rate constant for freshly reduced catalyst (as determined in the laboratory autoclave), was monitored throughout the reporting period. During a six-week test at a reactor temperature of 225oC and Balanced Gas flowrate of 700 KSCFH, the rate of decline in catalyst activity was steady at 0.29-0.36% per day. During a second one-month test at a reactor temperature of 220oC and a Balanced Gas flowrate of 550-600 KSCFH, the rate of decline in catalyst activity was 0.4% per day, which matched the pefiorrnance at 225"C, as well as the 4-month proof-of-concept run at the LaPorte AFDU in 1988/89. Beginning on 08 May 1998, the LPMEOW Reactor temperature was increased to 235oC, which was the operating temperature tier the December 1997 restart with the fresh charge of catalyst (50'Yo of design loading). The flowrate of the primary syngas feed stream (Balanced Gas) was also increased to 700-750 KSCFH. During two stable operating periods between 08 May and 09 June 1998, the average catalyst deactivation rate was 0.8% per day. Due to the scatter of the statistical analysis of the results, this test was extended to better quanti& the catalyst aging behavior. During the reporting perio~ two batches of fresh catalyst were activated and transferred to the reactor (on 02 April and 20 June 1998). The weight of catalyst in the LPMEOW Reactor has reached 80% of the design value. At the end of the reporting period, a step-change in the pressure-drop profile within the LPMEOW Reactor and an increase in the pressure of the steam system which provides cooling to the LPMEOW Reactor were observed. No change in the calculated activity of the catalyst was detected during either of these transients. These parameters will be monitored closely for any additional changes.

  16. Commercial-Scale Demonstration of the Liquid Phase Methanol (LPMEOH(TM)) Process

    SciTech Connect

    1997-06-30

    The Liquid Phase Methanol (LPMEOHTM) Demonstration Project at Kingsport, Tennessee, is a $213.7 million cooperative agreement between the U.S. Department of Energy (DOE) and Air Products Liquid Phase Conversion Company, L.P. (the Partnership). Air Products and Chemicals, Inc. (Air Products) and Eastman Chemical Company (Eastman) formed the Partnership to execute the Demonstration Project. The LPMEOIYM Process Demonstration Unit was built at a site located at the Eastman complex in Kingsport. During this quarter, comments from the DOE on the Topical Report "Economic Analysis - LPMEOHTM Process as an Add-on to IGCC for Coproduction" were received. A recommendation to continue with design verification testing for the coproduction of dimethyl ether (DIME) and methanol was made. DME design verification testing studies show the liquid phase DME (LPDME) process will have a significant economic advantage for the coproduction of DME for local markets. An LPDME catalyst system with reasonable long-term activity and stability is being developed. A recommendation document summarizing catalyst targets, experimental results, and the corresponding economics for a commercially successful LPDME catalyst was issued on 30 June 1997. The off-site, product-use test plan was updated in June of 1997. During this quarter, Acurex Environmental Corporation and Air Products screened proposals for this task by the likelihood of the projects to proceed and the timing for the initial methanol requirement. Eight sites from the list have met these criteria. The formal submission of the eight projects for review and concurrence by the DOE will be made during the next reporting period. The site paving and final painting were completed in May of 1997. Start-up activities were completed during the reporting period, and the initial methanol production from the demonstration unit occurred on 02 April 1997. The first extended stable operation at the nameplate capacity of 80,000 gallons per day (260 tons per day) took place on 06 April 1997. Pressure drop and resistance coefficient across the gas sparger at the bottom of the reactor increased over this initial operating period. The demonstration unit was shut down from 08 May -17 June 1997 as part of a scheduled complex outage for the Kingsport site. During this outage, the gas sparger was removed, cleaned, and reinstalled. After completion of other maintenance activities, the demonstration unit was restarted, and maintained stable operation through the remainder of the reporting period. Again, the gas sparger showed an increase in pressure drop and resistance since the restart, although not as rapidly as during the April-May operation. Fresh oil was introduced online for the first time to a new flush connection on the gas inlet line to the reactov the flush lowered the pressure drop by 1 psi. However, the effects were temporary, and the sparger resistance coefficient continued to increase. Additional flushing with both fresh oil and entrained slurry recovered in the cyclone and secondary oil knock-out drum will be attempted in order to stabilize the sparger resistance coefficient.

  17. Fabrication of commercial-scale fiber-reinforced hot-gas filters by chemical vapor deposition

    SciTech Connect

    White, L.R.

    1992-11-01

    Goal was to fabricate a filter for removing particulates from hot gases; principal applications would be in advanced utility processes such as pressurized fluidized bed combustion or coal gasification combined cycle systems. Filters were made in two steps: make a ceramic fiber preform and coat it with SiC by chemical vapor infiltration (CVD). The most promising construction was felt/filament wound. Light, tough ceramic composite filters can be made; reinforcement by continuous fibers is needed to avoid brittleness. Direct metal to filter contact does not damage the top which simplifies installation. However, much of the filter surface of felt/filament wound structures is closed over by the CVD coating, and the surface is rough and subject to delamination. Recommendations are given for improving the filters.

  18. Laboratory to commercial scale - Correlation in the physical properties of biofiber-polymer composites.

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Bio-fiber polymer composites have been the focus of automotive and building products industries for the last several years. Significant research has been done to improve the processing and performance characteristics of the bio-fiber composite. Most of the initial research is conducted on a small sc...

  19. Commercial scale demonstration enhanced oil recovery by micellar-polymer flood. Technical progress report, November 1984

    SciTech Connect

    Mueller, L.M.

    1984-01-01

    This report describes work conducted on the Maraflood oil recovery process, M-1 Project, throughout the month of November, 1984. Information is presented under two Work Breakdown Structure (WBS) elements: WBS 2100 - Fluid Injection and WBS 2300 - Performance Monitoring. Fluid Injection reporting includes a discussion of hydrogen peroxide stimulation of twelve 5.0-acre injection wells. Performance Monitoring reporting includes discussions of the 2.5-acre and 5.0-acre pattern oil cut performance for November, 1984, the October, 1984, high sulfonate content wells, and the October, 1984, tritiated water analysis. 16 figures.

  20. Commercial scale demonstration enhanced oil recovery by micellar-polymer flood. Monthly progress report, March 1985

    SciTech Connect

    Mueller, L.M.

    1985-03-01

    This report describes work conducted on the Maraflood oil recovery process, M-1 Project, throughout the month of March 1985. Information is presented under two Work Breakdown Structure (WBS) elements: WBS 2300 - performance monitoring; and WBS 2400 - economic monitoring. Performance monitoring reporting includes discussions of the 2.5-acre and 5.0-acre pattern oil cut performance for March 1985. Economic monitoring discusses the abandonment of one producing well in the 2.5-acre pattern area of the M-1 Project. 15 figures.

  1. Commercial scale demonstration enhanced oil recovery by micellar-polymer flood. Technical progress report

    SciTech Connect

    Mueller, L.M.

    1985-10-01

    This report describes work conducted on the Maraflood oil recovery process, M-1 Project, throughout the month of October, 1985. Information is presented under two Work Breakdown Structure (WBS) elements: WBS 2100 - Fluid Injection and WBS 2300 - Performance Monitoring. Fluid Injection reporting consists of a short discussion concerning injection wells recently stimulated in the 5.0-acre pattern area and the reason for this area's sudden injection rate increase. Performance Monitoring reporting includes a discussion of the 2.5-acre and 5.0-acre pattern oil cut performance for October, 1985. 16 figs.

  2. 75 FR 32171 - American Electric Power Service Corporation's Mountaineer Commercial Scale Carbon Capture and...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-06-07

    ... facility using Alstom's chilled ammonia process that would capture approximately 1.5 million metric tons... deployment of the chilled ammonia process for CO 2 capture and sequestration of CO 2 in a saline formation... Project AEP proposes to design, construct, and operate a CCS facility using Alstom's chilled...

  3. Microenvironmental air quality impact of a commercial-scale biomass heating system.

    PubMed

    Tong, Zheming; Yang, Bo; Hopke, Philip K; Zhang, K Max

    2017-01-01

    Initiatives to displace petroleum and climate change mitigation have driven a recent increase in space heating with biomass combustion. However, there is ample evidence that biomass combustion emits significant quantities of health damaging pollutants. We investigated the near-source micro-environmental air quality impact of a biomass-fueled combined heat and power system equipped with an electrostatic precipitator (ESP) in Syracuse, NY. Two rooftop sampling stations with PM2.5 and CO2 analyzers were established in such that one could capture the plume while the other one served as the background for comparison depending on the wind direction. Four sonic anemometers were deployed around the stack to quantify spatially and temporally resolved local wind patterns. Fuel-based emission factors were derived based on near-source measurement. The Comprehensive Turbulent Aerosol Dynamics and Gas Chemistry (CTAG) model was then applied to simulate the spatial variations of primary PM2.5 without ESP. Our analysis shows that the absence of ESP could lead to an almost 7 times increase in near-source primary PM2.5 concentrations with a maximum concentration above 100 μg m(-3) at the building rooftop. The above-ground "hotspots" would pose potential health risks to building occupants since particles could penetrate indoors via infiltration, natural ventilation, and fresh air intakes on the rooftop of multiple buildings. Our results demonstrated the importance of emission control for biomass combustion systems in urban area, and the need to take above-ground pollutant "hotspots" into account when permitting distributed generation. The effects of ambient wind speed and stack temperature, the suitability of airport meteorological data on micro-environmental air quality were explored, and the implications on mitigating near-source air pollution were discussed.

  4. Reference Materials and Reference Measurement Procedures: An Overview from a National Metrology Institute

    PubMed Central

    Bunk, David M

    2007-01-01

    An outline of the processes involved in both certified clinical reference material production and clinical reference measurement procedure development at the National Institute of Standards and Technology (NIST), the national metrology institute of the United States, is presented. The role that NIST and other national metrology institutes play in the metrological traceability of certified reference material is discussed. Highlighted are the challenges associated with the development of reference measurement systems for complex clinical analytes, such as proteins, and examples of existing efforts in this area are given. Examples of recent international collaborations in developing certified reference materials for analytes such as cardiac troponin I, brain natriuretic peptide, and serum creatinine demonstrate the close cooperation that national metrology institutes must have with the clinical community to establish complete reference measurement systems. PMID:18392127

  5. Comparison of select reference management tools.

    PubMed

    Zhang, Yingting

    2012-01-01

    Bibliographic management tools have been widely used by researchers to store, organize, and manage their references for research papers, theses, dissertations, journal articles, and other publications. There are a number of reference management tools available. In order for users to decide which tool is best for their needs, it is important to know each tool's strengths and weaknesses. This article compares four reference management tools, one of which is licensed by University of Medicine and Dentistry of New Jersey libraries and the other three are open source and freely available. They were chosen based on their functionality, ease of use, availability to library users, and popularity. These four tools are EndNote/EndNote Web, Zotero, Connotea, and Mendeley Desktop/Mendeley Web. Each tool is analyzed in terms of the following features: accessing, collecting, organizing, collaborating, and citing/formatting. A comparison table is included to summarize the key features of these tools.

  6. Integrative analysis of 111 reference human epigenomes.

    PubMed

    Kundaje, Anshul; Meuleman, Wouter; Ernst, Jason; Bilenky, Misha; Yen, Angela; Heravi-Moussavi, Alireza; Kheradpour, Pouya; Zhang, Zhizhuo; Wang, Jianrong; Ziller, Michael J; Amin, Viren; Whitaker, John W; Schultz, Matthew D; Ward, Lucas D; Sarkar, Abhishek; Quon, Gerald; Sandstrom, Richard S; Eaton, Matthew L; Wu, Yi-Chieh; Pfenning, Andreas R; Wang, Xinchen; Claussnitzer, Melina; Liu, Yaping; Coarfa, Cristian; Harris, R Alan; Shoresh, Noam; Epstein, Charles B; Gjoneska, Elizabeta; Leung, Danny; Xie, Wei; Hawkins, R David; Lister, Ryan; Hong, Chibo; Gascard, Philippe; Mungall, Andrew J; Moore, Richard; Chuah, Eric; Tam, Angela; Canfield, Theresa K; Hansen, R Scott; Kaul, Rajinder; Sabo, Peter J; Bansal, Mukul S; Carles, Annaick; Dixon, Jesse R; Farh, Kai-How; Feizi, Soheil; Karlic, Rosa; Kim, Ah-Ram; Kulkarni, Ashwinikumar; Li, Daofeng; Lowdon, Rebecca; Elliott, GiNell; Mercer, Tim R; Neph, Shane J; Onuchic, Vitor; Polak, Paz; Rajagopal, Nisha; Ray, Pradipta; Sallari, Richard C; Siebenthall, Kyle T; Sinnott-Armstrong, Nicholas A; Stevens, Michael; Thurman, Robert E; Wu, Jie; Zhang, Bo; Zhou, Xin; Beaudet, Arthur E; Boyer, Laurie A; De Jager, Philip L; Farnham, Peggy J; Fisher, Susan J; Haussler, David; Jones, Steven J M; Li, Wei; Marra, Marco A; McManus, Michael T; Sunyaev, Shamil; Thomson, James A; Tlsty, Thea D; Tsai, Li-Huei; Wang, Wei; Waterland, Robert A; Zhang, Michael Q; Chadwick, Lisa H; Bernstein, Bradley E; Costello, Joseph F; Ecker, Joseph R; Hirst, Martin; Meissner, Alexander; Milosavljevic, Aleksandar; Ren, Bing; Stamatoyannopoulos, John A; Wang, Ting; Kellis, Manolis

    2015-02-19

    The reference human genome sequence set the stage for studies of genetic variation and its association with human disease, but epigenomic studies lack a similar reference. To address this need, the NIH Roadmap Epigenomics Consortium generated the largest collection so far of human epigenomes for primary cells and tissues. Here we describe the integrative analysis of 111 reference human epigenomes generated as part of the programme, profiled for histone modification patterns, DNA accessibility, DNA methylation and RNA expression. We establish global maps of regulatory elements, define regulatory modules of coordinated activity, and their likely activators and repressors. We show that disease- and trait-associated genetic variants are enriched in tissue-specific epigenomic marks, revealing biologically relevant cell types for diverse human traits, and providing a resource for interpreting the molecular basis of human disease. Our results demonstrate the central role of epigenomic information for understanding gene regulation, cellular differentiation and human disease.

  7. Towards future reference systems for GM analysis.

    PubMed

    Trapmann, Stefanie; Corbisier, Philippe; Schimmel, Heinz; Emons, Hendrik

    2010-03-01

    Despite the fact that the measurement unit for the quantification of GMOs in food and feed products has not yet been unambiguously agreed upon in Europe, international trade requires reliable GMO analysis measuring comparably the GMO content of products. The two reference systems, based either on mass fractions or on copy number ratios, and their metrological traceability chains are presented and discussed. It is concluded that, properly established and expressed, measurement results in copy number ratios can provide a metrologically sound reference system. In this case, certified reference materials used for calibration and quality control can be independent of each other and the uncertainty derived from calibration can correctly be included in the overall uncertainty of the GMO measurement. However, further efforts are required to establish this metrological system.

  8. Reference frequency transmission over optical fiber

    NASA Technical Reports Server (NTRS)

    Lutes, G.; Kirk, A.

    1986-01-01

    A 100-MHz reference frequency from a hydrogen maser frequency standard has been transmitted via optical fiber over a 14-km distance with a measured stability of 1.5 X 10 to the-15 power for 1000 seconds averaging time. This capability was demonstrated in a frequency distribution experiment performed in April, 1986. The reference frequency was transmitted over a single-mode fiber-optic link from Deep Space Station (DSS) 13 to DSS 12 and back. The background leading up to the experiment and the significance of stable reference frequency distribution in the Deep Space Network (DSN) is discussed. Also described are the experiment, including the fiber-optic link, the measurement method and equipment, and finally the results of the experiment.

  9. Frequency References for Gravitational Wave Missions

    NASA Technical Reports Server (NTRS)

    Preston, Alix; Thrope, J. I.; Donelan, D.; Miner, L.

    2012-01-01

    The mitigation of laser frequency noise is an important aspect of interferometry for LISA-like missions. One portion of the baseline mitigation strategy in LISA is active stabilization utilizing opto-mechanical frequency references. The LISA optical bench is an attractive place to implement such frequency references due to its environmental stability and its access to primary and redundant laser systems. We have made an initial investigation of frequency references constructed using the techniques developed for the LISA and LISA Pathfinder optical benches. Both a Mach-Zehnder interferometer and triangular Fabry-Perot cavity have been successfully bonded to a Zerodur baseplate using the hydroxide bonding method. We will describe the construction of the bench along with preliminary stability results.

  10. International Geomagnetic Reference Field: the third generation.

    USGS Publications Warehouse

    Peddie, N.W.

    1982-01-01

    In August 1981 the International Association of Geomagnetism and Aeronomy revised the International Geomagnetic Reference Field (IGRF). It is the second revision since the inception of the IGRF in 1968. The revision extends the earlier series of IGRF models from 1980 to 1985, introduces a new series of definitive models for 1965-1976, and defines a provisional reference field for 1975- 1980. The revision consists of: 1) a model of the main geomagnetic field at 1980.0, not continuous with the earlier series of IGRF models together with a forecast model of the secular variation of the main field during 1980-1985; 2) definitive models of the main field at 1965.0, 1970.0, and 1975.0, with linear interpolation of the model coefficients specified for intervening dates; and 3) a provisional reference field for 1975-1980, defined as the linear interpolation of the 1975 and 1980 main-field models.-from Author

  11. European Vertical Reference System Influence in Latvia

    NASA Astrophysics Data System (ADS)

    Celms, A.; Reķe, I.; Ratkevičs, A.

    2015-11-01

    Till 1 December, 2014, in Latvia the heights were determined in Baltic Normal Height System 1977. The national height system is determined by the Cabinet of Ministers and internal laws. Now for the change of the national height system to reconcile it with the European Vertical Reference System, amendments to the laws and regulations have been developed, but so far only the amendment to the Geospatial Information Law is in force, the amendment to the regulation of the Cabinet of Ministers is still not approved. This amendment declares the Latvia Height System based on the European Vertical Reference System in Latvia as the national height system. For height transformation, there is a transformation formula for each European country. After calculations it is seen that height difference between Baltic Normal Height System 1977 and European Vertical Reference System depends on point location in the territory (coordinates). This unequal height difference between both height systems will cause unequal height values on border connection points between Baltic countries. The aim of the research is to evaluate the European Vertical Reference System in Latvia. To reach the aim the following tasks are set: 1) to evaluate the components of transformation formulas; 2) using the transformation formulas to calculate height differences between Baltic Normal Height System 1977 and the European Vertical Reference System realization EVRF2007 for the territory of Latvia and also between Baltic Normal Height System 1977 and the Latvia Normal Height System; 3) to get height differences in the European Vertical Reference System on the borderlines of Latvia - Estonia and Latvia - Lithuania.

  12. The Region 4 collaborative virtual reference project.

    PubMed

    Parker, Sandi K; Johnson, E Diane

    2003-01-01

    In May 2002, the Denison Memorial Library at the University of Colorado Health Sciences Center and the J. Otto Lottes Health Sciences Library at the University of Missouri-Columbia, with funding from the National Network of Libraries of Medicine-Midcontinental Region, embarked on a collaborative, real-time reference project using the 24/7 Reference, Inc., software package. This paper describes how the project was conceived, and includes details on the service hours, staffing, training, marketing, lessons learned, and future plans for the service.

  13. Preparation of Reference Material 8504, Transformer Oil.

    PubMed

    Poster, Dianne L; Schantz, Michele M; Wise, Stephen A

    2005-01-01

    A new reference material (RM), RM 8504, has been prepared for use as a diluent oil with Aroclors in transformer oil Standard Reference Materials (SRMs) 3075 to 3080 and SRM 3090 when developing and validating methods for the determination of polychlorinated biphenyls (PCBs) as Aroclors in transformer oil or similar matrices. SRMs 3075-3080 and SRM 3090 consist of individual Aroclors in the same transformer oil that was used to prepare RM 8504. A unit of RM 8504 consists of one bottle containing approximately 100 mL of transformer oil. No additional constituents have been added to the oil.

  14. Predictor-Based Model Reference Adaptive Control

    NASA Technical Reports Server (NTRS)

    Lavretsky, Eugene; Gadient, Ross; Gregory, Irene M.

    2009-01-01

    This paper is devoted to robust, Predictor-based Model Reference Adaptive Control (PMRAC) design. The proposed adaptive system is compared with the now-classical Model Reference Adaptive Control (MRAC) architecture. Simulation examples are presented. Numerical evidence indicates that the proposed PMRAC tracking architecture has better than MRAC transient characteristics. In this paper, we presented a state-predictor based direct adaptive tracking design methodology for multi-input dynamical systems, with partially known dynamics. Efficiency of the design was demonstrated using short period dynamics of an aircraft. Formal proof of the reported PMRAC benefits constitute future research and will be reported elsewhere.

  15. Multistatic radar: Synchronization and time reference system

    NASA Astrophysics Data System (ADS)

    Jubrink, H. G.

    1994-08-01

    A synchronization and time reference system for multistatic radar (MSR) is presented. The report also gives a summary of the most important parameter values of the synchronization process in MSR. Some reference oscillator systems using Loran C and global positioning system (GPS) receivers have been briefly analyzed. The synchronization method is based on a multioscillator system from the HP time and frequency standard system, the HP 55000 system. The multioscillator concept gives a more robust and redundant solution of the synchronization problem. The synchronization system can also be given external support by other time precision systems, for instance the GPS system.

  16. Ray Effect Mitigation Through Reference Frame Rotation

    DOE PAGES

    Tencer, John

    2016-05-01

    The discrete ordinates method is a popular and versatile technique for solving the radiative transport equation, a major drawback of which is the presence of ray effects. Mitigation of ray effects can yield significantly more accurate results and enhanced numerical stability for combined mode codes. Moreover, when ray effects are present, the solution is seen to be highly dependent upon the relative orientation of the geometry and the global reference frame. It is an undesirable property. A novel ray effect mitigation technique of averaging the computed solution for various reference frame orientations is proposed.

  17. 33 CFR 242.3 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false References. 242.3 Section 242.3 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE FLOOD PLAIN... Engineers Engineering Regulation 1105-2-100, Planning Guidance Notebook. (c) Corps of Engineers...

  18. 33 CFR 242.3 - References.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 33 Navigation and Navigable Waters 3 2013-07-01 2013-07-01 false References. 242.3 Section 242.3 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE FLOOD PLAIN... Engineers Engineering Regulation 1105-2-100, Planning Guidance Notebook. (c) Corps of Engineers...

  19. 33 CFR 242.3 - References.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 33 Navigation and Navigable Waters 3 2011-07-01 2011-07-01 false References. 242.3 Section 242.3 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE FLOOD PLAIN... Engineers Engineering Regulation 1105-2-100, Planning Guidance Notebook. (c) Corps of Engineers...

  20. 10 CFR 420.6 - Reference standards.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ...) The American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE), 1791 Tullie...-1989, entitled “Energy Efficient Design of New Buildings Except Low-Rise Residential Buildings,” with... 10 Energy 3 2012-01-01 2012-01-01 false Reference standards. 420.6 Section 420.6 Energy...

  1. 10 CFR 420.6 - Reference standards.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ...) The American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE), 1791 Tullie...-1989, entitled “Energy Efficient Design of New Buildings Except Low-Rise Residential Buildings,” with... 10 Energy 3 2014-01-01 2014-01-01 false Reference standards. 420.6 Section 420.6 Energy...

  2. New Brunswick. Reference Series No. 31.

    ERIC Educational Resources Information Center

    Department of External Affairs, Ottawa (Ontario).

    This booklet, one of a series featuring the Canadian provinces, presents a brief overview of New Brunswick and is suitable for teacher reference or student reading. Separate sections discuss cities and population, geography, history, politics, economy, manufacturing, forestry, agriculture, fisheries, mining, electricity, transportation, government…

  3. Check Firing of Master and Reference Propellants

    DTIC Science & Technology

    2014-12-08

    test. e. Record caliber, model, and serial number of recoil mechanism, gun , tube, and carriage. ** Superscript numbers correspond to Appendix...Measurement and Inspection of Gun Tubes. 2. TOP 04-2-606, Establishment of Master and Reference Calibration Rounds. 3. ITOP 04-2-805, Projectile

  4. Grants Program Seeks Reliable Reference Data.

    ERIC Educational Resources Information Center

    Dagani, Ron

    1980-01-01

    Announces the availability of grants from the National Bureau of Standards for the compilation of reliable reference data and the weeding out of faulty data. The grants are in response to the demand for data in all areas of science and technology. (Author/SA)

  5. Using Instant Messaging for Online Reference Service

    ERIC Educational Resources Information Center

    Forster, Shirley

    2006-01-01

    Many libraries are using co-browsing chat products to provide reference services to their patrons, whilst their patrons are online and using the internet. The concept of such an online service is highly desirable, but many libraries are concerned that they will never be able to afford such a system. This may have changed: Instant Messaging (IM)…

  6. Handbook of Reference Sources. Second Edition.

    ERIC Educational Resources Information Center

    Nichols, Margaret Irby

    Designed to serve as a selection aid for small public libraries and to list important sources available through the major resource centers of the Texas Library System, this bibliography lists 804 annotated reference sources with 126 additional works named within the annotations. The books are grouped into 18 major areas, each of which is broken…

  7. Comparative Elections: Building a Basic Reference Collection.

    ERIC Educational Resources Information Center

    Nalen, James E.

    2001-01-01

    This annotated bibliography focuses on resources for the study of international elections and electoral systems and outcomes that will be useful for collection development and for answering reference questions about foreign elections. Discusses comparative politics, comparative elections, and possible electoral reform. (LRW)

  8. Mechanical Energy Change in Inertial Reference Frames

    ERIC Educational Resources Information Center

    Ghanbari, Saeed

    2016-01-01

    The mechanical energy change of a system in an inertial frame of reference equals work done by the total nonconservative force in the same frame. This relation is covariant under the Galilean transformations from inertial frame S to S', where S' moves with constant velocity relative to S. In the presence of nonconservative forces, such as normal…

  9. Preventing Sexual Abuse. Reference Sheet 8.

    ERIC Educational Resources Information Center

    Britton, Patti O., Ed.; McGee, Michael, Ed.

    This reference book, developed to present options for the prevention and treatment of child sexual abuse, contains descriptions of creative approaches used to address the problem of child sexual abuse. Some of the programs described offer active and entertaining interventions, such as puppet shows, coloring books, stories, teddy bears, and…

  10. 33 CFR 230.3 - References.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ..., 1981 (46 FR 13193, February 19, 1981). (b) Executive Order 12114, Environmental Effects Abroad of Major Federal Actions, January 4, 1979 (44 FR 1957, January 9, 1979). (c) Clean Water Act (formerly known as the Federal Water Pollution Control Act) 33 U.S.C. 1344 (hereinafter referred to as section 404)....

  11. Reference breast temperature: proposal of an equation

    PubMed Central

    de Souza, Gladis Aparecida Galindo Reisemberger; Brioschi, Marcos Leal; Vargas, José Viriato Coelho; Morais, Keli Cristiane Correia; Dalmaso, Carlos; Neves, Eduardo Borba

    2015-01-01

    ABSTRACT Objective To develop an equation to estimate the breast reference temperature according to the variation of room and core body temperatures. Methods Four asymptomatic women were evaluated for three consecutive menstrual cycles. Using thermography, the temperature of breasts and eyes was measured as indirect reference of core body and room temperatures. To analyze the thermal behavior of the breasts during the cycle, the core body and room temperatures were normalized by means of a mathematical equation. Results We performed 180 observations and the core temperature had the highest correlation with the breast temperature, followed by room temperature. The proposed prediction model could explain 45.3% of the breast temperature variation, with variable room temperature variable; it can be accepted as a way to estimate the reference breast temperature at different room temperatures. Conclusion The average breast temperature in healthy women had a direct relation with the core and room temperature and can be estimated mathematically. It is suggested that an equation could be used in clinical practice to estimate the normal breast reference temperature in young women, regardless of the day of the cycle, therefore assisting in evaluation of anatomical studies. PMID:26761549

  12. A Reference Grammar of Spoken Kannada.

    ERIC Educational Resources Information Center

    Schiffman, Harold

    This reference grammar is a description of the speech of educated people of the Bangalore/Mysore area of Karnataka State in South India. This particular dialect is used in films and, to some extent, on the radio. The four sections of the book deal with: (1) phonology, (2) the noun phrase, (3) the verb phrase, and (4) syntax. Each item that is…

  13. 40 CFR 90.7 - Reference materials.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ....116; 90.509. (2) SAE material. The following table sets forth material from the Society of Automotive...., Warrendale, PA 15096-0001. Document number and name 40 CFR part 90 reference SAE J1930 September 1991, Electrical/Electronic Systems Diagnostic Terms, Definitions, Abbreviations and Acronyms 90.114 SAE...

  14. 40 CFR 90.7 - Reference materials.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ....116; 90.509. (2) SAE material. The following table sets forth material from the Society of Automotive...., Warrendale, PA 15096-0001. Document number and name 40 CFR part 90 reference SAE J1930 September 1991, Electrical/Electronic Systems Diagnostic Terms, Definitions, Abbreviations and Acronyms 90.114 SAE...

  15. 40 CFR 89.6 - Reference materials.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ...” 89.120; 89.207; 89.509. (2) SAE material. The following table sets forth material from the Society of... Commonwealth Dr., Warrendale, PA 15096-0001. Document number and name 40 CFR part 89 reference SAE J244 June 83: Recommended Practice for Measurement of Intake Air or Exhaust Gas Flow of Diesel Engines 89.416-96 SAE...

  16. 40 CFR 89.6 - Reference materials.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...” 89.120; 89.207; 89.509. (2) SAE material. The following table sets forth material from the Society of... Commonwealth Dr., Warrendale, PA 15096-0001. Document number and name 40 CFR part 89 reference SAE J244 June 83: Recommended Practice for Measurement of Intake Air or Exhaust Gas Flow of Diesel Engines 89.416-96 SAE...

  17. Reference Lists for HECE Occupational Areas.

    ERIC Educational Resources Information Center

    Texas Education Agency, Austin. Dept. of Occupational Education and Technology.

    The annotated bibliography contains citations to appropriate reference books, pamphlets and audiovisual materials for the following 17 occupations: art and craft aide, bridal consultant, child care aide, clothing assistant, companion to the elderly, consumer aide, dietetic aide, fabric coordinator, fashion coordinator, floral designer, food…

  18. Veterinary Accreditation. A Reference Guide for Practitioners.

    ERIC Educational Resources Information Center

    Animal and Plant Health Inspection Service (USDA), Washington, DC.

    This reference manual was designed as a guide for veterinarians who have been accredited by the U.S. Department of Agriculture (USDA) Animal and Plant Health Inspection Services. The guide provides instructions on the following topics: identifying animals, reportable diseases and conditions, brucellosis, tuberculosis, pseudorabies, miscellaneous…

  19. 33 CFR 183.310 - Reference areas.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... is the forwardmost 2 feet of the top surface of the hull or deck as illustrated in Figure 9. (b) The aft reference area of a boat is the aftmost two feet of the top surface of the hull or deck,...

  20. 33 CFR 183.210 - Reference areas.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... is the forward most 2 feet of the top surface of the hull or deck, as illustrated in Figure 9. (b) The aft reference area of a boat is the aft most two feet of the top surface of the hull or deck,...

  1. 33 CFR 183.210 - Reference areas.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... is the forward most 2 feet of the top surface of the hull or deck, as illustrated in Figure 9. (b) The aft reference area of a boat is the aft most two feet of the top surface of the hull or deck,...

  2. 33 CFR 183.310 - Reference areas.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... is the forwardmost 2 feet of the top surface of the hull or deck as illustrated in Figure 9. (b) The aft reference area of a boat is the aftmost two feet of the top surface of the hull or deck,...

  3. Selected Reference Books, 2000-2001.

    ERIC Educational Resources Information Center

    McIlvaine, Eileen

    2001-01-01

    Presents a selection of recent scholarly and general reference works in these areas: periodical indexes; literature, including theater; religion; festivals; architecture; music; social sciences; women's studies; and history. Provides a brief roundup of new editions of standard works at the end. (AEF)

  4. Genetics Home Reference: familial adenomatous polyposis

    MedlinePlus

    ... Järvinen HJ, Peltomäki P. The complex genotype-phenotype relationship in familial adenomatous polyposis. Eur J Gastroenterol Hepatol. ... healthcare professional . About Genetics Home Reference Site Map Customer Support Selection Criteria for Links USA.gov Copyright ...

  5. 15 CFR 2008.1 - References.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 15 Commerce and Foreign Trade 3 2011-01-01 2011-01-01 false References. 2008.1 Section 2008.1 Commerce and Foreign Trade Regulations Relating to Foreign Trade Agreements OFFICE OF THE UNITED STATES TRADE REPRESENTATIVE REGULATIONS TO IMPLEMENT E.O. 12065; OFFICE OF THE UNITED STATES...

  6. 15 CFR 2008.1 - References.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 15 Commerce and Foreign Trade 3 2010-01-01 2010-01-01 false References. 2008.1 Section 2008.1 Commerce and Foreign Trade Regulations Relating to Foreign Trade Agreements OFFICE OF THE UNITED STATES TRADE REPRESENTATIVE REGULATIONS TO IMPLEMENT E.O. 12065; OFFICE OF THE UNITED STATES...

  7. Management & Supervision Personnel Administration Training; General Reference.

    ERIC Educational Resources Information Center

    United States Government Printing Office, Washington, DC. Training and Career Development Div.

    This report lists 329 books in the library of the Training and Career Development Division of the Personnel Service. The books are listed under six categories. They are: personnel administration (46), management and supervision (60), general reference (57), training (20), American Management Association (AMA) publications (118), and United States…

  8. Building Complex Reference Objects from Dual Sets

    ERIC Educational Resources Information Center

    Patson, Nikole D.; Warren, Tessa

    2011-01-01

    There has been considerable psycholinguistic investigation into the conditions that allow separately introduced individuals to be joined into a plural set and represented as a complex reference object (e.g., Eschenbach et al., 1989; Garrod & Sanford, 1982; Koh & Clifton, 2002; Koh et al., 2008; Moxey, Sanford, Sturt, & Morrow, 2004; Sanford &…

  9. Ask a Librarian: Florida's Virtual Reference Service

    ERIC Educational Resources Information Center

    Sachs, Diana

    2004-01-01

    Florida's Ask a Librarian service (http://www.askalibrarian.org) brings virtual reference to users at their moment of need via the Internet. Ask a Librarian is a growing service with 76 participating libraries including public, school, four-year, and community college libraries. The following article describes how Ask a Librarian was developed…

  10. A Reference Unit on Home Vegetable Gardening.

    ERIC Educational Resources Information Center

    McCully, James S., Comp.; And Others

    Designed to provide practical, up-to-date, basic information on home gardening for vocational agriculture students with only a limited knowledge of vegetable gardening, this reference unit includes step-by-step procedures for planning, planting, cultivating, harvesting, and processing vegetables in a small plot. Topics covered include plot…

  11. 32 CFR 552.161 - References.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 32 National Defense 3 2014-07-01 2014-07-01 false References. 552.161 Section 552.161 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY MILITARY RESERVATIONS AND NATIONAL CEMETERIES REGULATIONS AFFECTING MILITARY RESERVATIONS Land Use Policy for Fort Lewis, Yakima Training...

  12. 32 CFR 552.161 - References.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 32 National Defense 3 2012-07-01 2009-07-01 true References. 552.161 Section 552.161 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY MILITARY RESERVATIONS AND NATIONAL CEMETERIES REGULATIONS AFFECTING MILITARY RESERVATIONS Land Use Policy for Fort Lewis, Yakima Training...

  13. 32 CFR 552.161 - References.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 3 2010-07-01 2010-07-01 true References. 552.161 Section 552.161 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY MILITARY RESERVATIONS AND NATIONAL CEMETERIES REGULATIONS AFFECTING MILITARY RESERVATIONS Land Use Policy for Fort Lewis, Yakima Training...

  14. Reference apparatus for medical ultrasonic transducer

    NASA Technical Reports Server (NTRS)

    Lee, R. D.; Hudock, R. J.; Shute, D. I.

    1974-01-01

    Once reference apparatus has been located properly, and its position on chest of patient has been recorded on skin by means of indelible fiducial marks, it is simple matter at later time to reposition probe on chest over heart. In this way, signals from exact same area of heart can be re-examined.

  15. 15 CFR 2008.1 - References.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 15 Commerce and Foreign Trade 3 2012-01-01 2012-01-01 false References. 2008.1 Section 2008.1 Commerce and Foreign Trade Regulations Relating to Foreign Trade Agreements OFFICE OF THE UNITED STATES TRADE REPRESENTATIVE REGULATIONS TO IMPLEMENT E.O. 12065; OFFICE OF THE UNITED STATES...

  16. 15 CFR 2008.1 - References.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 15 Commerce and Foreign Trade 3 2013-01-01 2013-01-01 false References. 2008.1 Section 2008.1 Commerce and Foreign Trade Regulations Relating to Foreign Trade Agreements OFFICE OF THE UNITED STATES TRADE REPRESENTATIVE REGULATIONS TO IMPLEMENT E.O. 12065; OFFICE OF THE UNITED STATES...

  17. 15 CFR 2008.1 - References.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 15 Commerce and Foreign Trade 3 2014-01-01 2014-01-01 false References. 2008.1 Section 2008.1 Commerce and Foreign Trade Regulations Relating to Foreign Trade Agreements OFFICE OF THE UNITED STATES TRADE REPRESENTATIVE REGULATIONS TO IMPLEMENT E.O. 12065; OFFICE OF THE UNITED STATES...

  18. Electronic Reference Service. SPEC Kit 251.

    ERIC Educational Resources Information Center

    Goetsch, Lori, Comp.

    1999-01-01

    The goals of this SPEC Kit were to report on the extent to which ARL (Association of Research Libraries) libraries provide electronic reference services and to offer a snapshot of the types of users reached, questions received, policies established, data-gathering techniques utilized, and innovations implemented. The first section of the kit…

  19. 77 FR 16761 - Incorporation by Reference

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-03-22

    ...; ] OFFICE OF THE FEDERAL REGISTER 1 CFR Part 51 Incorporation by Reference AGENCY: Office of the Federal... Register (OFR or we) received a petition to revise our regulations at 1 CFR part 51 on February 13, 2012... 11414. You can view the petition and its suggested revisions to the regulations 1 CFR part 51 on...

  20. 78 FR 69006 - Incorporation by Reference

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-11-18

    ... reference into the Code of Federal Regulations. Given the recent government shutdown and technical issues... following methods: Federal eRulemaking Portal: http://www.regulations.gov/#!docketDetail ;D=OFR-2013-0001... the Code of Federal Regulations (77 FR 11414 (February 27, 2012)). Given the recent...