Satellite power system concept development and evaluation program system definition technical assessment report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1980-12-01

The results of the system definition studies conducted by NASA as a part of the Department of Energy/National Aeronautics and Space Administration SPS Concept Development and Evaluation Program are summarized. The purpose of the system definition efforts was to identify and define candidate SPS concepts and to evaluate the concepts in terms of technical and cost factors. Although the system definition efforts consisted primarily of evaluation and assessment of alternative technical approaches, a reference system was also defined to facilitate economic, environmental, and societal assessments by the Department of Energy. This reference system was designed to deliver 5 GW ofmore » electrical power to the utility grid. Topics covered include system definition; energy conversion and power management; power transmission and reception; structures, controls, and materials; construction and operations; and space transportation.« less

Application of adaptive antenna techniques to future commercial satellite communication

NASA Technical Reports Server (NTRS)

Ersoy, L.; Lee, E. A.; Matthews, E. W.

1987-01-01

The purpose of this contract was to identify the application of adaptive antenna technique in future operational commercial satellite communication systems and to quantify potential benefits. The contract consisted of two major subtasks. Task 1, Assessment of Future Commercial Satellite System Requirements, was generally referred to as the Adaptive section. Task 2 dealt with Pointing Error Compensation Study for a Multiple Scanning/Fixed Spot Beam Reflector Antenna System and was referred to as the reconfigurable system. Each of these tasks was further sub-divided into smaller subtasks. It should also be noted that the reconfigurable system is usually defined as an open-loop system while the adaptive system is a closed-loop system. The differences between the open- and closed-loop systems were defined. Both the adaptive and reconfigurable systems were explained and the potential applications of such systems were presented in the context of commercial communication satellite systems.

Application of adaptive antenna techniques to future commercial satellite communications. Executive summary

NASA Technical Reports Server (NTRS)

Ersoy, L.; Lee, E. A.; Matthews, E. W.

1987-01-01

The purpose of this contract was to identify the application of adaptive antenna technique in future operational commercial satellite communication systems and to quantify potential benefits. The contract consisted of two major subtasks. Task 1, Assessment of Future Commercial Satellite System Requirements, was generally referred to as the Adaptive section. Task 2 dealt with Pointing Error Compensation Study for a Multiple Scanning/Fixed Spot Beam Reflector Antenna System and was referred to as the reconfigurable system. Each of these tasks was further subdivided into smaller subtasks. It should also be noted that the reconfigurable system is usually defined as an open-loop system while the adaptive system is a closed-loop system. The differences between the open- and closed-loop systems were defined. Both the adaptive and reconfigurable systems were explained and the potential applications of such systems were presented in the context of commercial communication satellite systems.

The Study and Measurement of Values and Attitudes.

ERIC Educational Resources Information Center

Kerlinger, Fred N.

The author defines values, attitudes, and beliefs according to their relation to referents. A referent is a construct standing for a set or category of social objects, ideas, or behaviors that is the focus of an attitude. Attitudes and values are belief systems. Beliefs are enduring cognitions about referents; beliefs reflect the value and…

System for monitoring non-coincident, nonstationary process signals

DOEpatents

Gross, Kenneth C.; Wegerich, Stephan W.

2005-01-04

An improved system for monitoring non-coincident, non-stationary, process signals. The mean, variance, and length of a reference signal is defined by an automated system, followed by the identification of the leading and falling edges of a monitored signal and the length of the monitored signal. The monitored signal is compared to the reference signal, and the monitored signal is resampled in accordance with the reference signal. The reference signal is then correlated with the resampled monitored signal such that the reference signal and the resampled monitored signal are coincident in time with each other. The resampled monitored signal is then compared to the reference signal to determine whether the resampled monitored signal is within a set of predesignated operating conditions.

Defining life: connecting robotics and chemistry.

PubMed

Brack, André; Troublé, Michel

2010-04-01

Life is commonly referred as open systems driven by organic chemistry capable to self reproduce and to evolve. The notion of life has also been extended to non chemical systems such as robots. The key characteristics of living systems, i.e. autonomy, self-replication, self-reproduction, self-organization, self-aggregation, autocatalysis, as defined in chemistry and in robotics, are compared in a dialogue between a chemist and a robotitian.

Implementing system simulation of C3 systems using autonomous objects

NASA Technical Reports Server (NTRS)

Rogers, Ralph V.

1987-01-01

The basis of all conflict recognition in simulation is a common frame of reference. Synchronous discrete-event simulation relies on the fixed points in time as the basic frame of reference. Asynchronous discrete-event simulation relies on fixed-points in the model space as the basic frame of reference. Neither approach provides sufficient support for autonomous objects. The use of a spatial template as a frame of reference is proposed to address these insufficiencies. The concept of a spatial template is defined and an implementation approach offered. Discussed are the uses of this approach to analyze the integration of sensor data associated with Command, Control, and Communication systems.

Self-replicating systems: A systems engineering approach

NASA Technical Reports Server (NTRS)

Vontiesenhausen, G.; Darbro, W. A.

1980-01-01

A first approach to conceptualize self-replicating systems was developed from past and present abstract theories. The engineering elements of self-replicating systems are defined in terms of a basic reference system. A number of options are investigated. The growth characteristics and their problems are analyzed, the mathematics of various exponential growth options are outlined, and the problems of universal parts production and systems closure are discussed. Selected areas of further study are defined and a 20 year development and demonstration program is presented.

Current state of the mass storage system reference model

NASA Technical Reports Server (NTRS)

Coyne, Robert

1993-01-01

IEEE SSSWG was chartered in May 1990 to abstract the hardware and software components of existing and emerging storage systems and to define the software interfaces between these components. The immediate goal is the decomposition of a storage system into interoperable functional modules which vendors can offer as separate commercial products. The ultimate goal is to develop interoperable standards which define the software interfaces, and in the distributed case, the associated protocols to each of the architectural modules in the model. The topics are presented in viewgraph form and include the following: IEEE SSSWG organization; IEEE SSSWG subcommittees & chairs; IEEE standards activity board; layered view of the reference model; layered access to storage services; IEEE SSSWG emphasis; and features for MSSRM version 5.

Defining biophysical reference conditions for dynamics river systems: an Alaskan example

NASA Astrophysics Data System (ADS)

Pess, G. R.

2008-12-01

Defining reference conditions for dynamic river ecosystems is difficult for two reasons. First long-term, persistent anthropogenic influences such as land development, harvest of biological resources, and invasive species have resulted in degraded, reduced, and simplified ecological communities and associated habitats. Second, river systems that have not been altered through human disturbance rarely have a long-term dataset on ecological conditions. However there are exceptions which can help us define the dynamic nature of river ecosystems. One large-scale exception is the Wood River system in Bristol Bay, Alaska, where habitat and salmon populations have not been altered by anthropogenic influences such as land development, hatchery production, and invasive species. In addition, the one major anthropogenic disturbance, salmon (Oncorhynchus spp.) harvest, has been quantified and regulated since its inception. First, we examined the variation in watershed and stream habitat characteristics across the Wood River system. We then compared these stream habitat characteristics with data that was collected in the 1950s. Lastly, we examined the correlation between pink (Oncorhynchus gorbuscha), chum (O. keta), and Chinook (O. tshawytscha), and sockeye salmon (O. nerka), and habitat characteristics in the Wood River system using four decades of data on salmon. We found that specific habitat attributes such as stream channel wetted width, depth, cover type, and the proportion of spawnable area were similar to data collected in the 1950s. Greater stream habitat variation occurred among streams than over time. Salmon occurrence and abundance, however was more temporal and spatially variable. The occurrence of pink and chum salmon increased from the 1970's to the present in the Wood River system, while sockeye abundance has fluctuated with changes in ocean conditions. Pink, Chinook and chum salmon ranged from non-existent to episodic to abundantly perennial, while sockeye dominated all streams in the Wood River system. One main trend was the frequency of occurrence and abundance of pink, Chinook, and chum salmon increased with watershed drainage area and stream depth and, to a lesser extent, decreased with sockeye salmon density. Conversely, sockeye salmon densities decreased with watershed drainage area and stream depth. Wood river habitat was temporally stable and spatially variable, thus identifying the suite of stream channel types that occur and identifying reference states for each is critical to capture reference conditions. Wood River biological reference states need to be established over a longer time frame than physical attributes because of the large-scale temporal variability that is forced by climatic conditions and larger scale spatially- explicit trends. Thus biological reference states for the Wood River system need to be defined with multiple streams, similar to developing reference states for different stream channel types, in order to capture the range of biological variability.

OWL references in ORM conceptual modelling

NASA Astrophysics Data System (ADS)

Matula, Jiri; Belunek, Roman; Hunka, Frantisek

2017-07-01

Object Role Modelling methodology is the fact-based type of conceptual modelling. The aim of the paper is to emphasize a close connection to OWL documents and its possible mutual cooperation. The definition of entities or domain values is an indispensable part of the conceptual schema design procedure defined by the ORM methodology. Many of these entities are already defined in OWL documents. Therefore, it is not necessary to declare entities again, whereas it is possible to utilize references from OWL documents during modelling of information systems.

Intelligence Defined and Undefined: A Relativistic Appraisal

ERIC Educational Resources Information Center

Wechsler, David

1975-01-01

Major reasons for the continuing divergency of opinion as regards the nature and meaning of intelligence are examined. An appraisal of intelligence as a relative concept is proposed which advocates the necessity of specifying the reference systems to which a statement about intelligence refers. (EH)

The effect of referral and transfer patients on hospital funding in a capitated health care delivery system.

PubMed

Pietz, Kenneth; Byrne, Margaret M; Daw, Christina; Petersen, Laura A

2007-10-01

(1) To investigate whether inpatients referred or transferred between facilities result in increased financial loss compared with those admitted directly, in a health care delivery system funded by capitation methods. (2) To determine whether the higher cost of those patients transferred or referred is fairly compensated by a diagnosis-based risk adjustment system, and whether tertiary care facilities bear an unfair financial burden for such patients in a capitated financing environment. The study cohort included all Veterans Affairs (VA) beneficiaries who received inpatient care during fiscal year (FY) 2004. Referral was defined as an outpatient visit to 1 facility followed by an admission to another facility. Transfers were consecutive inpatient stays at different hospitals. We defined loss as cost minus the share of budget determined by a Diagnostic Cost Group-based allocation. Both t tests and linear regression were used to compare the effect on cost and loss for patients transferred or not and referred or not. Mean loss to a facility for patients transferred in was 1231 dollars more than for those not transferred. Mean loss for referred patients was 3341 dollars more than for those not referred, controlling for disease burden. For tertiary hospitals, the difference in losses for transfer patients was less than for other hospitals but greater for referral patients. Patients referred or transferred from other facilities are more costly than those who are not. The difference may not be compensated by a diagnosis-based allocation system. A capitated health care system may consider additional funding to cover the cost of such patients.

Reference manual for a Requirements Specification Language (RSL), version 2.0

NASA Technical Reports Server (NTRS)

Fisher, Gene L.; Cohen, Gerald C.

1993-01-01

This report is a Reference Manual for a general-purpose Requirements Specification Language, RSL. The purpose of RSL is to specify precisely the external structure of a mechanized system and to define requirements that the system must meet. A system can be comprised of a mixture of hardware, software, and human processing elements. RSL is a hybrid of features found in several popular requirements specification languages and includes constructs for formal mathematical specification.

NASIS data base management system - IBM 360/370 OS MVT implementation. 5: Retrieval command system reference manual

NASA Technical Reports Server (NTRS)

1973-01-01

The retrieval command subsystem reference manual for the NASA Aerospace Safety Information System (NASIS) is presented. The output oriented classification of retrieval commands provides the user with the ability to review a set of data items for verification or inspection as a typewriter or CRT terminal and to print a set of data on a remote printer. Predefined and user-definable data formatting are available for both output media.

STAR (Simple Tool for Automated Reasoning): Tutorial guide and reference manual

NASA Technical Reports Server (NTRS)

Borchardt, G. C.

1985-01-01

STAR is an interactive, interpreted programming language for the development and operation of Artificial Intelligence application systems. The language is intended for use primarily in the development of software application systems which rely on a combination of symbolic processing, central to the vast majority of AI algorithms, with routines and data structures defined in compiled languages such as C, FORTRAN and PASCAL. References to routines and data structures defined in compiled languages are intermixed with symbolic structures in STAR, resulting in a hybrid operating environment in which symbolic and non-symbolic processing and organization of data may interact to a high degree within the execution of particular application systems. The STAR language was developed in the course of a project involving AI techniques in the interpretation of imaging spectrometer data and is derived in part from a previous language called CLIP. The interpreter for STAR is implemented as a program defined in the language C and has been made available for distribution in source code form through NASA's Computer Software Management and Information Center (COSMIC). Contained within this report are the STAR Tutorial Guide, which introduces the language in a step-by-step manner, and the STAR Reference Manual, which provides a detailed summary of the features of STAR.

Recording multiple spatially-heterodyned direct to digital holograms in one digital image

DOEpatents

Hanson, Gregory R [Clinton, TN; Bingham, Philip R [Knoxville, TN

2008-03-25

Systems and methods are described for recording multiple spatially-heterodyned direct to digital holograms in one digital image. A method includes digitally recording, at a first reference beam-object beam angle, a first spatially-heterodyned hologram including spatial heterodyne fringes for Fourier analysis; Fourier analyzing the recorded first spatially-heterodyned hologram by shifting a first original origin of the recorded first spatially-heterodyned hologram to sit on top of a first spatial-heterodyne carrier frequency defined by the first reference beam-object beam angle; digitally recording, at a second reference beam-object beam angle, a second spatially-heterodyned hologram including spatial heterodyne fringes for Fourier analysis; Fourier analyzing the recorded second spatially-heterodyned hologram by shifting a second original origin of the recorded second spatially-heterodyned hologram to sit on top of a second spatial-heterodyne carrier frequency defined by the second reference beam-object beam angle; applying a first digital filter to cut off signals around the first original origin and define a first result; performing a first inverse Fourier transform on the first result; applying a second digital filter to cut off signals around the second original origin and define a second result; and performing a second inverse Fourier transform on the second result, wherein the first reference beam-object beam angle is not equal to the second reference beam-object beam angle and a single digital image includes both the first spatially-heterodyned hologram and the second spatially-heterodyned hologram.

49 CFR 571.104 - Standard No. 104; Windshield wiping and washing systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

...,” of SAE Aerospace-Automotive Drawing Standards (1963) (incorporated by reference, see § 571.5... body width dimension “W116”, as defined in section E, “Ground Vehicle Practice,” of SAE Aerospace... Aerospace-Automotive Drawing Standards (1963) (incorporated by reference, see § 571.5). 95 percent eye range...

49 CFR 571.104 - Standard No. 104; Windshield wiping and washing systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

...,” of SAE Aerospace-Automotive Drawing Standards (1963) (incorporated by reference, see § 571.5... body width dimension “W116”, as defined in section E, “Ground Vehicle Practice,” of SAE Aerospace... Aerospace-Automotive Drawing Standards (1963) (incorporated by reference, see § 571.5). 95 percent eye range...

Body mass index and childhood obesity classification systems: A comparison of the French, International Obesity Task Force (IOTF) and World Health Organization (WHO) references.

PubMed

Kêkê, L M; Samouda, H; Jacobs, J; di Pompeo, C; Lemdani, M; Hubert, H; Zitouni, D; Guinhouya, B C

2015-06-01

This study aims to compare three body mass index (BMI)-based classification systems of childhood obesity: the French, the International Obesity Task Force (IOTF) and the World Health Organization (WHO) references. The study involved 1382 schoolchildren, recruited from the Lille Academic District in France in May 2009 aged 8.4±1.7 years (4.0-12.0 years). Their mean height and body mass were 131.5±10.9cm and 30.7±9.2kg, respectively, resulting in a BMI of 17.4±3.2kg/m(2). The weight status was defined according to the three systems considered in this study. The agreement between these references was tested using the Cohen's kappa coefficient. The prevalence of overweight was higher with the WHO references (20.0%) in comparison with the French references (13.8%; P<0.0001) and the IOTF (16.2%; P≤0.01). A similar result was found with obesity (WHO: 11.6% vs. IOTF: 6.7%; or French references: 6.7%; P<0.0001). Agreement between the three references ranged from "moderate" to "perfect" (0.43≤κ≤1.00; P<0.0001). Kappa coefficients were higher when the three references were used to classify children as obese (0.63≤κ≤1.00; P<0.0001) as compared to classification in the overweight (obesity excluded) category (0.43≤κ≤0.94; P<0.0001). When sex and age categories (4-6 years vs. 7-12 years) were considered to define the overweight status, the lowest kappa coefficient was found between the French and WHO references in boys aged 7-12 years (κ=0.28; P<0.0001), and the highest one in girls aged 7-12 years between the French references and IOTF (κ=0.97; P<0.0001). As for obesity, agreement between the three references ranged from 0.60 to 1.00 (P<0.0001), with the lowest values obtained in the comparison of the WHO references against French references or IOTF among boys aged 7-12 years (κ=0.60; P<0.0001). Overall, the WHO references yield an overestimation in overweight and/or obesity within this sample of schoolchildren as compared to the French references and the IOTF. The magnitude of agreement coefficients between the three references depends on of both sex and age categories. The French references seem to be in rather close agreement with the IOTF in defining overweight, especially in 7-12-year-old children. Copyright © 2015 Elsevier Masson SAS. All rights reserved.

Spatial-heterodyne interferometry for transmission (SHIFT) measurements

DOEpatents

Bingham, Philip R.; Hanson, Gregory R.; Tobin, Ken W.

2006-10-10

Systems and methods are described for spatial-heterodyne interferometry for transmission (SHIFT) measurements. A method includes digitally recording a spatially-heterodyned hologram including spatial heterodyne fringes for Fourier analysis using a reference beam, and an object beam that is transmitted through an object that is at least partially translucent; Fourier analyzing the digitally recorded spatially-heterodyned hologram, by shifting an original origin of the digitally recorded spatially-heterodyned hologram to sit on top of a spatial-heterodyne carrier frequency defined by an angle between the reference beam and the object beam, to define an analyzed image; digitally filtering the analyzed image to cut off signals around the original origin to define a result; and performing an inverse Fourier transform on the result.

Reference condition approach to restoration planning

USGS Publications Warehouse

Nestler, J.M.; Theiling, C.H.; Lubinski, S.J.; Smith, D.L.

2010-01-01

Ecosystem restoration planning requires quantitative rigor to evaluate alternatives, define end states, report progress and perform environmental benefits analysis (EBA). Unfortunately, existing planning frameworks are, at best, semi-quantitative. In this paper, we: (1) describe a quantitative restoration planning approach based on a comprehensive, but simple mathematical framework that can be used to effectively apply knowledge and evaluate alternatives, (2) use the approach to derive a simple but precisely defined lexicon based on the reference condition concept and allied terms and (3) illustrate the approach with an example from the Upper Mississippi River System (UMRS) using hydrologic indicators. The approach supports the development of a scaleable restoration strategy that, in theory, can be expanded to ecosystem characteristics such as hydraulics, geomorphology, habitat and biodiversity. We identify three reference condition types, best achievable condition (A BAC), measured magnitude (MMi which can be determined at one or many times and places) and desired future condition (ADFC) that, when used with the mathematical framework, provide a complete system of accounts useful for goal-oriented system-level management and restoration. Published in 2010 by John Wiley & Sons, Ltd.

Unmanned aircraft system bridge inspection demonstration project phase II final report.

DOT National Transportation Integrated Search

2017-06-01

An Unmanned Aircraft System (UAS) is defined by the Federal Aviation Administration (FAA) as an aircraft operated without the possibility of direct human intervention from within the aircraft. Unmanned aircraft are familiarly referred to as drones, a...

A proposed application programming interface for a physical volume repository

NASA Technical Reports Server (NTRS)

Jones, Merritt; Williams, Joel; Wrenn, Richard

1996-01-01

The IEEE Storage System Standards Working Group (SSSWG) has developed the Reference Model for Open Storage Systems Interconnection, Mass Storage System Reference Model Version 5. This document, provides the framework for a series of standards for application and user interfaces to open storage systems. More recently, the SSSWG has been developing Application Programming Interfaces (APIs) for the individual components defined by the model. The API for the Physical Volume Repository is the most fully developed, but work is being done on APIs for the Physical Volume Library and for the Mover also. The SSSWG meets every other month, and meetings are open to all interested parties. The Physical Volume Repository (PVR) is responsible for managing the storage of removable media cartridges and for mounting and dismounting these cartridges onto drives. This document describes a model which defines a Physical Volume Repository, and gives a brief summary of the Application Programming Interface (API) which the IEEE Storage Systems Standards Working Group (SSSWG) is proposing as the standard interface for the PVR.

F-15/nonaxisymmetric nozzle system integration study support program

NASA Technical Reports Server (NTRS)

Stevens, H. L.

1978-01-01

Nozzle and cooling methods were defined and analyzed to provide a viable system for demonstration 2-D nozzle technology on the F-15 aircraft. Two candidate cooling systems applied to each nozzle were evaluated. The F-100 engine mount and case modifications requirements were analyzed and the actuation and control system requirements for two dimensional nozzles were defined. Nozzle performance changes relative to the axisymmetric baseline nozzle were evaluated and performance and weight characteristics for axisymmetric reference configurations were estimated. The infrared radiation characteristics of these nozzles installed on the F-100 engine were predicted. A full scale development plan with associated costs to carry the F100 engine/two-dimensional (2-D) nozzle through flight tests was defined.

Spatial-Heterodyne Interferometry For Reflection And Transm Ission (Shirt) Measurements

DOEpatents

Hanson, Gregory R [Clinton, TN; Bingham, Philip R [Knoxville, TN; Tobin, Ken W [Harriman, TN

2006-02-14

Systems and methods are described for spatial-heterodyne interferometry for reflection and transmission (SHIRT) measurements. A method includes digitally recording a first spatially-heterodyned hologram using a first reference beam and a first object beam; digitally recording a second spatially-heterodyned hologram using a second reference beam and a second object beam; Fourier analyzing the digitally recorded first spatially-heterodyned hologram to define a first analyzed image; Fourier analyzing the digitally recorded second spatially-heterodyned hologram to define a second analyzed image; digitally filtering the first analyzed image to define a first result; and digitally filtering the second analyzed image to define a second result; performing a first inverse Fourier transform on the first result, and performing a second inverse Fourier transform on the second result. The first object beam is transmitted through an object that is at least partially translucent, and the second object beam is reflected from the object.

Intra- and extra-articular planes of reference for use in total hip arthroplasty: a preliminary study.

PubMed

Hausselle, Jerome; Moreau, Pierre Etienne; Wessely, Loic; de Thomasson, Emmanuel; Assi, Ayman; Parratte, Sebastien; Essig, Jerome; Skalli, Wafa

2012-08-01

Acetabular component malalignment in total hip arthroplasty can lead to potential complications such as dislocation, component impingement and excessive wear. Computer-assisted orthopaedic surgery systems generally use the anterior pelvic plane (APP). Our aim was to investigate the reliability of anatomical landmarks accessible during surgery and to define new potential planes of reference. Three types of palpations were performed: virtual, on dry bones and on two cadaveric specimens. Four landmarks were selected, the reproducibility of their positioning ranging from 0.9 to 2.3 mm. We then defined five planes and tested them during palpations on two cadaveric specimens. Two planes produced a mean orientation error of 5.0° [standard deviation (SD 3.3°)] and 5.6° (SD 2.7°). Even if further studies are needed to test the reliability of such planes on a larger scale in vivo during surgery, these results demonstrated the feasibility of defining a new plane of reference as an alternative to the APP.

Satellite power systems (SPS) concept definition study. Volume 1: Executive summary

NASA Technical Reports Server (NTRS)

Hanley, G. M.

1980-01-01

System definition studies resulted in a further definition of the reference system using gallium arsenide solar arrays, analysis of alternative subsystem options for the reference concept, preliminary solid state microwave concept studies, and an environmental analysis of laser transmission systems. The special emphasis studies concentrated on satellite construction, satellite construction base definition, satellite construction base construction, and rectenna construction. Major emphasis in the transportation studies was put on definition of a two stage parallel burn, vertical takeoff/horizontal landing concept. The electric orbit transfer vehicle was defined in greater detail. Program definition included cost analyses and schedule definition.

The Many Dimensions of Program Management

NASA Technical Reports Server (NTRS)

Dean, Edwin B.

1992-01-01

For the purposes of this paper, program refers to a collection of activities or projects which must be performed according to a plan or schedule. The Space Exploration Initiative within the National Aeronautics and Space Administration (NASA) is an example. Dimensionality refers to both the various perspectives of a program and to the components within that perspective. It is, thus, appropriate to think of dimensions of dimensionality. For example, one dimension or perspective of a program is the projects which perform the program. Within the project dimension, the individual projects are the components of that dimensionality. The number of projects defines the spatial dimensionality of the project dimension. Thus, each perspective or dimension has a dimensionality of its own. The structure and associated values of all the various perspectives of a program define the program. A project refers to the collection of activities required to conceive, sell, design, develop, evaluate, produce, operate, support, evolve, and retire a given system. A project thus effects the life cycle of given system. A project is, thus, the system to conceive, sell, design, develop, evaluate, produce, operate, support, evolve, and retire a system. A program, thus, effects the life cycle of the collection of projects required to effect the collection of systems required to implement the program.

Automatic quadrature control and measuring system. [using optical coupling circuitry

NASA Technical Reports Server (NTRS)

Hamlet, J. F. (Inventor)

1974-01-01

A quadrature component cancellation and measuring system comprising a detection system for detecting the quadrature component from a primary signal, including reference circuitry to define the phase of the quadrature component for detection is described. A Raysistor optical coupling control device connects an output from the detection system to a circuit driven by a signal based upon the primary signal. Combining circuitry connects the primary signal and the circuit controlled by the Raysistor device to subtract quadrature components. A known current through the optically sensitive element produces a signal defining the magnitude of the quadrature component.

Aerospace physiology.

DOT National Transportation Integrated Search

2004-01-01

This document defines the protocol standards for the Internet Protocol Suite (IPS), which is commonly referred to as Transmission Control Protocol/Internet Protocol (TCP/IP) protocols used for data communications within the National Airspace System (...

Advanced Life Support Research and Technology Development Metric: Fiscal Year 2003

NASA Technical Reports Server (NTRS)

Hanford, A. J.

2004-01-01

This document provides the official calculation of the Advanced Life Support (ALS) Research and Technology Development Metric (the Metric) for Fiscal Year 2003. As such, the values herein are primarily based on Systems Integration, Modeling, and Analysis (SIMA) Element approved software tools or reviewed and approved reference documents. The Metric is one of several measures employed by the National Aeronautics and Space Administration (NASA) to assess the Agency s progress as mandated by the United States Congress and the Office of Management and Budget. Because any measure must have a reference point, whether explicitly defined or implied, the Metric is a comparison between a selected ALS Project life support system and an equivalently detailed life support system using technology from the Environmental Control and Life Support System (ECLSS) for the International Space Station (ISS). More specifically, the Metric is the ratio defined by the equivalent system mass (ESM) of a life support system for a specific mission using the ISS ECLSS technologies divided by the ESM for an equivalent life support system using the best ALS technologies. As defined, the Metric should increase in value as the ALS technologies become lighter, less power intensive, and require less volume. For Fiscal Year 2003, the Advanced Life Support Research and Technology Development Metric value is 1.47 for an Orbiting Research Facility and 1.36 for an Independent Exploration Mission.

Multiparameter optimization of mammography: an update

NASA Astrophysics Data System (ADS)

Jafroudi, Hamid; Muntz, E. P.; Jennings, Robert J.

1994-05-01

Previously in this forum we have reported the application of multiparameter optimization techniques to the design of a minimum dose mammography system. The approach used a reference system to define the physical imaging performance required and the dose to which the dose for the optimized system should be compared. During the course of implementing the resulting design in hardware suitable for laboratory testing, the state of the art in mammographic imaging changed, so that the original reference system, which did not have a grid, was no longer appropriate. A reference system with a grid was selected in response to this change, and at the same time the optimization procedure was modified, to make it more general and to facilitate study of the optimized design under a variety of conditions. We report the changes in the procedure, and the results obtained using the revised procedure and the up- to-date reference system. Our results, which are supported by laboratory measurements, indicate that the optimized design can image small objects as well as the reference system using only about 30% of the dose required by the reference system. Hardware meeting the specification produced by the optimization procedure and suitable for clinical use is currently under evaluation in the Diagnostic Radiology Department at the Clinical Center, NH.

Spatial Reasoning in Tenejapan Mayans

PubMed Central

Li, Peggy; Abarbanell, Linda; Gleitman, Lila; Papafragou, Anna

2011-01-01

Language communities differ in their stock of reference frames (coordinate systems for specifying locations and directions). English typically uses egocentrically defined axes (e.g., “left-right”), especially when describing small-scale relationships. Other languages such as Tseltal Mayan prefer to use geocentrically-defined axes (e.g., “north-south”) and do not use any type of projective body-defined axes. It has been argued that the availability of specific frames of reference in language determines the availability or salience of the corresponding spatial concepts. In four experiments, we explored this hypothesis by testing Tseltal speakers’ spatial reasoning skills. Whereas most prior tasks in this domain were open-ended (allowing several correct solutions), the present tasks required a unique solution that favored adopting a frame of reference that was either congruent or incongruent with what is habitually lexicalized in the participants’ language. In these tasks, Tseltal speakers easily solved the language-incongruent problems, and performance was generally more robust for these than for the language-congruent problems that favored geocentrically-defined coordinates. We suggest thatlisteners’ probabilistic inferences when instruction is open to more than one interpretation account for why there are greater cross-linguistic differences in the solutions to open-ended spatial problems than to less ambiguous ones. PMID:21481854

75 FR 38779 - Nomination of Existing Marine Protected Areas to the National System of Marine Protected Areas

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-06

... managing agencies to fill key conservation gaps in important ocean areas. DATES: Comments on the... conservation objectives of the Framework. Executive Order 13158 defines an MPA as: ``any area of the marine... term MPA as defined in the Framework refers only to the marine portion of a site (below the mean high...

Defining And Employing Reference Conditions For Ecological Restoration Of The Lower Missouri River, USA

NASA Astrophysics Data System (ADS)

Jacobson, R. B.; Elliott, C. M.; Reuter, J. M.

2008-12-01

Ecological reference conditions are especially challenging for large, intensively managed rivers like the Lower Missouri. Historical information provides broad understanding of how the river has changed, but translating historical information into quantitative reference conditions remains a challenge. Historical information is less available for biological and chemical conditions than for physical conditions. For physical conditions, much of the early historical condition is documented in date-specific measurements or maps, and it is difficult to determine how representative these conditions are for a river system that was characterized historically by large floods and high channel migration rates. As an alternative to a historically defined least- disturbed condition, spatial variation within the Missouri River basin provides potential for defining a best- attainable reference condition. A possibility for the best-attainable condition for channel morphology is an unchannelized segment downstream of the lowermost dam (rkm 1298 - 1203). This segment retains multiple channels and abundant sandbars although it has a highly altered flow regime and a greatly diminished sediment supply. Conversely, downstream river segments have more natural flow regimes, but have been narrowed and simplified for navigation and bank stability. We use two computational tools to compensate for the lack of ideal reference conditions. The first is a hydrologic model that synthesizes natural and altered flow regimes based on 100 years of daily inputs to the river (daily routing model, DRM, US Army Corps of Engineers, 1998); the second tool is hydrodynamic modeling of habitat availability. The flow-regime and hydrodynamic outputs are integrated to define habitat-duration curves as the basis for reference conditions (least-disturbed flow regime and least-disturbed channel morphology). Lacking robust biological response models, we use mean residence time of water and a habitat diversity index as generic ecosystem indicators.

TRIM.FaTE Public Reference Library Documentation

EPA Pesticide Factsheets

TRIM.FaTE is a spatially explicit, compartmental mass balance model that describes the movement and transformation of pollutants over time, through a user-defined, bounded system that includes both biotic and abiotic compartments.

Developing sustainable transportation performance measures for ALDOT.

DOT National Transportation Integrated Search

2013-06-01

Sustainable transportation is generally used to refer to transportation that contributes to the sustainable development of the community that owns and uses the system. The Transportation Research Board defines sustainability as: Sustainability is ...

A reference architecture for telemonitoring.

PubMed

Clarke, Malcolm

2004-01-01

The Telecare Interactive Continuous Monitoring System exploits GPRS to provide an ambulatory device that monitors selected vital signs on a continuous basis. Alarms are sent when parameters fall outside preset limits, and accompanying physiological data may also be transmitted. The always-connected property of GPRS allows continuous interactive control of the device and its sensors, permitting changes to monitoring parameters or even enabling continuous monitoring of a sensor in emergency. A new personal area network (PAN) has been developed to support short-range wireless connection to sensors worn on the body including ECG and finger worn SpO2. Most notable is use of ultra low radio frequency to reduce power to minimum. The system has been designed to use a hierarchical architecture for sensors and "derived" signals, such as HR from ECG, so that each can be independently controlled and managed. Sensors are treated as objects, and functions are defined to control aspects of behaviour. These are refined in order to define a generic set of abstract functions to handle the majority of functions, leaving a minimum of sensor specific commands. The intention is to define a reference architecture in order to research the functionality and system architecture of a telemonitoring system. The Telecare project is funded through a grant from the European Commission (IST programme).

Development of an unmanned maritime system reference architecture

NASA Astrophysics Data System (ADS)

Duarte, Christiane N.; Cramer, Megan A.; Stack, Jason R.

2014-06-01

The concept of operations (CONOPS) for unmanned maritime systems (UMS) continues to envision systems that are multi-mission, re-configurable and capable of acceptable performance over a wide range of environmental and contextual variability. Key enablers for these concepts of operation are an autonomy module which can execute different mission directives and a mission payload consisting of re-configurable sensor or effector suites. This level of modularity in mission payloads enables affordability, flexibility (i.e., more capability with future platforms) and scalability (i.e., force multiplication). The modularity in autonomy facilitates rapid technology integration, prototyping, testing and leveraging of state-of-the-art advances in autonomy research. Capability drivers imply a requirement to maintain an open architecture design for both research and acquisition programs. As the maritime platforms become more stable in their design (e.g. unmanned surface vehicles, unmanned underwater vehicles) future developments are able to focus on more capable sensors and more robust autonomy algorithms. To respond to Fleet needs, given an evolving threat, programs will want to interchange the latest sensor or a new and improved algorithm in a cost effective and efficient manner. In order to make this possible, the programs need a reference architecture that will define for technology providers where their piece fits and how to successfully integrate. With these concerns in mind, the US Navy established the Unmanned Maritime Systems Reference Architecture (UMS-RA) Working Group in August 2011. This group consists of Department of Defense and industry participants working the problem of defining reference architecture for autonomous operations of maritime systems. This paper summarizes its efforts to date.

Development and Evaluation of Reference Standards for Image-based Telemedicine Diagnosis and Clinical Research Studies in Ophthalmology

PubMed Central

Ryan, Michael C.; Ostmo, Susan; Jonas, Karyn; Berrocal, Audina; Drenser, Kimberly; Horowitz, Jason; Lee, Thomas C.; Simmons, Charles; Martinez-Castellanos, Maria-Ana; Chan, R.V. Paul; Chiang, Michael F.

2014-01-01

Information systems managing image-based data for telemedicine or clinical research applications require a reference standard representing the correct diagnosis. Accurate reference standards are difficult to establish because of imperfect agreement among physicians, and discrepancies between clinical vs. image-based diagnosis. This study is designed to describe the development and evaluation of reference standards for image-based diagnosis, which combine diagnostic impressions of multiple image readers with the actual clinical diagnoses. We show that agreement between image reading and clinical examinations was imperfect (689 [32%] discrepancies in 2148 image readings), as was inter-reader agreement (kappa 0.490-0.652). This was improved by establishing an image-based reference standard defined as the majority diagnosis given by three readers (13% discrepancies with image readers). It was further improved by establishing an overall reference standard that incorporated the clinical diagnosis (10% discrepancies with image readers). These principles of establishing reference standards may be applied to improve robustness of real-world systems supporting image-based diagnosis. PMID:25954463

Sources and Information

ERIC Educational Resources Information Center

Rinnander, Elizabeth

1977-01-01

Reviews the literature pertinent to defining the goals of public relations, reaching out to the community, dealing with the media, and evaluation. All references have appeared in the ERIC system and major higher education journals since 1972. (Author/RT)

New International Agreements About Space Techniques Among Argentina, China and France

NASA Astrophysics Data System (ADS)

Pacheco, A. M.; Podestá, R.; Actis, E.; Adarvez, S.; Quinteros, J.; Li, J.; Saunier, J.; Podestá, F.; Ramos, F.; Aguilera, J.; Sosa, G.; Hauser, D.

2018-01-01

The International Earth Rotation and Reference Systems (IERS) is in charge of defining and materializing celestial reference systems (ICRS - ICRF) and terrestrial reference systems (ITRS - ITRF). In order to perform this task it uses data from the following techniques: Very Long Baseline Interferometry (VLBI), Satellite Laser Ranging (SLR), Global Navigation Satellite System (GNSS) and Doppler Orbitography and Radiopositioning Integrated by Satellite (DORIS). Nowadays, the Observatorio Astronómico Félix Aguilar (OAFA) has two instruments with these advanced techniques: SLR and a permanent GNSS station. In the nearby future a 40 m diameter radio telescope will be available that will be operated in VLBI mode along with a DORIS buoy which will be co-localized with a SLR telescope and GNSS antennas. In this way OAFA will become a zero station, first class, of the ITRF 2014 frame.

On the establishment and maintenance of a modern conventional terrestrial reference system

NASA Technical Reports Server (NTRS)

Bock, Y.; Zhu, S. Y.

1982-01-01

The frame of the Conventional Terrestrial Reference System (CTS) is defined by an adopted set of coordinates, at a fundamental epoxh, of a global network of stations which contribute the vertices of a fundamental polyhedron. A method to estimate this set of coordinates using a combination of modern three dimensional geodetic systems is presented. Once established, the function of the CTS is twofold. The first is to monitor the external (or global) motions of the polyhedron with respect to the frame of a Conventional Inertial Reference System, i.e., those motions common to all stations. The second is to monitor the internal motions (or deformations) of the polyhedron, i.e., those motions that are not common to all stations. Two possible estimators for use in earth deformation analysis are given and their statistical and physical properties are described.

Teaching and Learning Activity Sequencing System using Distributed Genetic Algorithms

NASA Astrophysics Data System (ADS)

Matsui, Tatsunori; Ishikawa, Tomotake; Okamoto, Toshio

The purpose of this study is development of a supporting system for teacher's design of lesson plan. Especially design of lesson plan which relates to the new subject "Information Study" is supported. In this study, we developed a system which generates teaching and learning activity sequences by interlinking lesson's activities corresponding to the various conditions according to the user's input. Because user's input is multiple information, there will be caused contradiction which the system should solve. This multiobjective optimization problem is resolved by Distributed Genetic Algorithms, in which some fitness functions are defined with reference models on lesson, thinking and teaching style. From results of various experiments, effectivity and validity of the proposed methods and reference models were verified; on the other hand, some future works on reference models and evaluation functions were also pointed out.

Satellite Power System (SPS) concept definition study (Exhibit D). Volume 2: Systems/subsystems analyses

NASA Technical Reports Server (NTRS)

Hanley, G. M.

1981-01-01

Modifications to the reference concept were studied and the best approaches defined. The impact of the high efficiency multibandgap solar array on the reference concept design is considered. System trade studies for several solid state concepts, including the sandwich concept and a separate antenna/solar concept, are described. Two solid state concepts were selected and a design definition is presented for each. Magnetrons as an alternative to the reference klystrons for dc/RF conversion are evaluated. System definitions are presented for the preferred klystron and solid state concepts. Supporting systems are analyzed, with major analysis in the microwave, structures, and power distribution areas. Results of studies for thermal control, attitude control, stationkeeping, and details of a multibandgap solar cell study are included. Advanced laser concepts and the meteorological effects of a laser beam power transmission concept are considered.

Space Communication and Navigation Testbed Communications Technology for Exploration

NASA Technical Reports Server (NTRS)

Reinhart, Richard

2013-01-01

NASA developed and launched an experimental flight payload (referred to as the Space Communication and Navigation Test Bed) to investigate software defined radio, networking, and navigation technologies, operationally in the space environment. The payload consists of three software defined radios each compliant to NASAs Space Telecommunications Radio System Architecture, a common software interface description standard for software defined radios. The software defined radios are new technology developed by NASA and industry partners. The payload is externally mounted to the International Space Station truss and available to NASA, industry, and university partners to conduct experiments representative of future mission capability. Experiment operations include in-flight reconfiguration of the SDR waveform functions and payload networking software. The flight system communicates with NASAs orbiting satellite relay network, the Tracking, Data Relay Satellite System at both S-band and Ka-band and to any Earth-based compatible S-band ground station.

The Current SI Seen From the Perspective of the Proposed New SI

PubMed Central

Taylor, Barry N.

2011-01-01

A revised International System of Units (SI) proposed by the International Committee for Weights and Measures is under consideration by the General Conference on Weights and Measures for eventual adoption. Widely recognized as a significant advance for both metrology and science, it is defined via statements that explicitly fix the numerical values of a selected set of seven reference constants when the values of these constants are expressed in certain specified units. At first sight this approach to defining a system of units appears to be quite different from that used to define the current SI. However, by showing how the definitions of the seven base units of the current SI also fix the numerical values of a set of seven reference constants (broadly interpreted) when the values of these constants are expressed in their coherent SI units, and how the definition of the current SI can be recast into the same form as that of the revised SI under consideration, we show that the revision is not as radical a departure from the current SI as it might initially seem. PMID:26989600

System and Method for Measuring the Transfer Function of a Guided Wave Device

NASA Technical Reports Server (NTRS)

Froggatt, Mark E. (Inventor); Erdogan, Turan (Inventor)

2002-01-01

A method/system are provided for measuring the NxN scalar transfer function elements for an N-port guided wave device. Optical energy of a selected wavelength is generated at a source and directed along N reference optical paths having N reference path lengths. Each reference optical path terminates in one of N detectors such that N reference signals are produced at the N detectors. The reference signals are indicative of amplitude, phase and frequency of the optical energy carried along the N reference optical paths. The optical energy from the source is also directed to the N-ports of the guided wave device and then on to each of the N detectors such that N measurement optical paths are defined between the source and each of the N detectors. A portion of the optical energy is modified in terms of at least one of the amplitude and phase to produce N modified signals at each of the N detectors. At each of the N detectors, each of the N modified signals is combined with a corresponding one of the N reference signals to produce corresponding N combined signals at each of the N detectors. A total of N(sup 2) measurement signals are generated by the N detectors. Each of the N(sup 2) measurement signals is sampled at a wave number increment (Delta)k so that N(sup 2) sampled signals are produced. The NxN transfer function elements are generated using the N(sup 2) sampled signals. Reference and measurement path length constraints are defined such that the N combined signals at each of the N detectors are spatially separated from one another in the time domain.

Spatial Data Transfer Standard (SDTS), part 5 : SDTS raster profile and extensions

DOT National Transportation Integrated Search

1999-02-01

The Spatial Data Transfer Standard (SDTS) defines a general mechanism for the transfer of : geographically referenced spatial data and its supporting metadata, i.e., attributes, data quality reports, : coordinate reference systems, security informati...

Vestibular recruitment

NASA Technical Reports Server (NTRS)

Tsemakhov, S. G.

1980-01-01

Vestibular recruitment is defined through the analysis of several references. It is concluded that vestibular recruitment is an objective phenomenon which manifests itself during the affection of the vestibular receptor and thus serves as a diagnostic tool during affection of the vestibular system.

Application of Millisecond Pulsar Timing to the Long-Term Stability of Clock Ensembles

NASA Technical Reports Server (NTRS)

Foster, Roger S.; Matsakis, Demetrios N.

1996-01-01

We review the application of millisecond pulsars to define a precise long-term standard and positional reference system in a nearly inertial reference frame. We quantify the current timing precision of the best millisecond pulsars and define the required precise time and time interval (PTTI) accuracy and stability to enable time transfer via pulsars. Pulsars may prove useful as independent standards to examine decade-long timing stability and provide an independent natural system within which to calibrate any new, perhaps vastly improved atomic time scale. Since pulsar stability appears to be related to the lifetime of the pulsar, the new millisecond pulsar J173+0747 is projected to have a 100-day accuracy equivalent to a single HP5071 cesium standard. Over the last five years, dozens of new millisecond pulsars have been discovered. A few of the new millisecond pulsars may have even better timing properties.

Space Communication and Navigation SDR Testbed, Overview and Opportunity for Experiments

NASA Technical Reports Server (NTRS)

Reinhart, Richard C.

2013-01-01

NASA has developed an experimental flight payload (referred to as the Space Communication and Navigation (SCAN) Test Bed) to investigate software defined radio (SDR) communications, networking, and navigation technologies, operationally in the space environment. The payload consists of three software defined radios each compliant to NASAs Space Telecommunications Radio System Architecture, a common software interface description standard for software defined radios. The software defined radios are new technology developments underway by NASA and industry partners launched in 2012. The payload is externally mounted to the International Space Station truss to conduct experiments representative of future mission capability. Experiment operations include in-flight reconfiguration of the SDR waveform functions and payload networking software. The flight system will communicate with NASAs orbiting satellite relay network, the Tracking and Data Relay Satellite System at both S-band and Ka-band and to any Earth-based compatible S-band ground station. The system is available for experiments by industry, academia, and other government agencies to participate in the SDR technology assessments and standards advancements.

Making Decisions in a Time of Fiscal Stringency: The Longer-Term Implications.

ERIC Educational Resources Information Center

Bowen, Frank M.

The concept of traditional planning, programming, and budgeting systems (PPBS) is defined and compared with imperative planning, a term used to refer to whatever procedures higher education officials use to integrate program planning and budgeting. The University of Wisconsin system is described as an example of emerging budgetary practice in…

Soft Systems Methodology and Problem Framing: Development of an Environmental Problem Solving Model Respecting a New Emergent Reflexive Paradigm.

ERIC Educational Resources Information Center

Gauthier, Benoit; And Others

1997-01-01

Identifies the more representative problem-solving models in environmental education. Suggests the addition of a strategy for defining a problem situation using Soft Systems Methodology to environmental education activities explicitly designed for the development of critical thinking. Contains 45 references. (JRH)

46 CFR 56.07-10 - Design conditions and criteria (modifies 101-104.7).

Code of Federal Regulations, 2010 CFR

2010-10-01

... ENGINEERING PIPING SYSTEMS AND APPURTENANCES Design § 56.07-10 Design conditions and criteria (modifies 101... system must not be greater than the internal design pressure defined in 104.1.2 of ASME B31.1 (incorporated by reference; see 46 CFR 56.01-2). (2) Where the maximum allowable working pressure of a system...

Spaceflight Human System Standards

NASA Technical Reports Server (NTRS)

Holubec, Keith; Tillman, Barry; Connolly, Jan

2009-01-01

NASA created a new approach for human system integration and human performance standards. NASA created two documents a standard and a reference handbook. The standard is titled NASA Space Flight Human-System Standard (SFHSS) and consists of two-volumes: Volume 1- Crew Health This volume covers standards needed to support astronaut health (medical care, nutrition, sleep, exercise, etc.) Volume 2 Human Factors, Habitability and Environmental Health This volume covers the standards for system design that will maintain astronaut performance (ie., environmental factors, design of facilities, layout of workstations, and lighting requirements). It includes classic human factors requirements. The new standards document is written in terms so that it is applicable to a broad range of present and future NASA systems. The document states that all new programs prepare system-specific requirements that will meet the general standards. For example, the new standard does not specify a design should accommodate specific percentiles of a defined population. Rather, NASA-STD-3001, Volume 2 states that all programs shall prepare program-specific requirements that define the user population and their size ranges. The design shall then accommodate the full size range of those users. The companion reference handbook, Human Integration Design Handbook (HIDH), was developed to capture the design consideration information from NASA-STD-3000, and adds spaceflight lessons learned, gaps in knowledge, example solutions, and suggests research to further mature specific disciplines. The HIDH serves two major purposes: HIDH is the reference document for writing human factors requirements for specific systems. HIDH contains design guidance information that helps insure that designers create systems which safely and effectively accommodate the capabilities and limitations of space flight crews.

Adaptive control in the presence of unmodeled dynamics. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Rohrs, C. E.

1982-01-01

Stability and robustness properties of a wide class of adaptive control algorithms in the presence of unmodeled dynamics and output disturbances were investigated. The class of adaptive algorithms considered are those commonly referred to as model reference adaptive control algorithms, self-tuning controllers, and dead beat adaptive controllers, developed for both continuous-time systems and discrete-time systems. A unified analytical approach was developed to examine the class of existing adaptive algorithms. It was discovered that all existing algorithms contain an infinite gain operator in the dynamic system that defines command reference errors and parameter errors; it is argued that such an infinite gain operator appears to be generic to all adaptive algorithms, whether they exhibit explicit or implicit parameter identification. It is concluded that none of the adaptive algorithms considered can be used with confidence in a practical control system design, because instability will set in with a high probability.

Focus control system for stretched-membrane mirror module

DOEpatents

Butler, B.L.; Beninga, K.J.

1991-05-21

A focus control system dynamically sets and controls the focal length of a reflective membrane supported between a perimeter frame. A rear membrane is also supported between the perimeter frame rearward and spaced apart from a back side of the reflective membrane. The space between the membranes defines a plenum space into which a mass of gas at a first pressure is inserted. The pressure differential between the first pressure and an external pressure, such as the atmospheric pressure, causes the reflective membrane to assume a first curvature relative to a reference plane associated with the perimeter frame. This curvature defines the focal length of the reflective membrane. The focal length is dynamically controlled by changing the volume of the plenum space, thereby changing the first pressure. The system can be used to change or maintain the pressure differential and hence the front membrane curvature. The plenum volume is changed by pushing or pulling on a central section of the rear membrane using a suitable actuator. Sensing means continuously sense the location of the reflective membrane relative to the reference plane. This sensed position is compared to a reference position, and a resulting error signal, comprising the difference between the sensed position and reference position, drives the actuator in a direction to minimize the difference. A vent value compensates for temperature changes or leaks in the closed volume by allowing the pressure differential to be adjusted as required to center the working range of the actuator about the desired focal length. 13 figures.

Focus control system for stretched-membrane mirror module

DOEpatents

Butler, Barry L.; Beninga, Kelly J.

1991-01-01

A focus control system dynamically sets and controls the focal length of a reflective membrane supported between a perimeter frame. A rear membrane is also supported between the perimeter frame rearward and spaced apart from a back side of the reflective membrane. The space between the membranes defines a plenum space into which a mass of gas at a first pressure is inserted. The pressure differential between the first pressure and an external pressure, such as the atmospheric pressure, causes the reflective membrane to assume a first curvature relative to a reference plane associated with the perimeter frame. This curvature defines the focal length of the reflective membrane. The focal length is dynamically controlled by changing the volume of the plenum space, thereby changing the first pressure. The system can be used to change or maintain the pressure differential and hence the front membrane curvature. The plenum volume is changed by pushing or pulling on a central section of the rear membrane using a suitable actuator. Sensing means continuously sense the location of the reflective membrane relative to the reference plane. This sensed position is compared to a reference position, and a resulting error signal, comprising the difference between the sensed position and reference position, drives the actuator in a direction to minimize the difference. A vent value compensates for temperature changes or leaks in the closed volume by allowing the pressure differential to be adjusted as required to center the working range of the actuator about the desired focal length.

GTA Welding Research and Development for Plutonium Containment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sessions, C.E.

2002-02-21

This paper discusses the development of two welding systems that are used to contain actinide metals and oxides for long term storage. The systems are termed the bagless transfer system (BTS) and the outer container welder (OCW) system. The BTS is so named because it permits the containment of actinides without a polymeric package (i.e., bag). The development of these two systems was directed by Department of Energy Standard 3013, hereafter referred to as DOE 3013. This document defines the product and container requirements. In addition, it references national codes and standards for leak rates, ANSI N14.5, and design, Americanmore » Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code Section VIII (BandPVC).« less

Time References in US and UK Astronomical and Navigational Almanacs

DTIC Science & Technology

2011-01-01

are also compatible with Teph and TDB. 2.4. Terrestrial and Barycentric Dynamic Times An apparent place, or equivalently the geocentric intermediate...right ascension and declination with respect to the CIO and equator of date, is defined in the Geocentric Celestial Reference System where the... Geocentric Coordinate Time (TCG) nor Barycentric Coordinate Time (TCB) is used in the US and UK almanacs for different reasons. TCG is a coordinate time

Considering Time-Scale Requirements for the Future

DTIC Science & Technology

2013-05-01

geocentric reference frame with the SI second realized on the rotating geoid as the scale unit. It is a continuous atomic time scale that was...the B8lycentric and Geocentric Celestial Reference Systems, two time scales, Barycentric Coor- dinate Time (TCB) and Geocentric Coordinate Time (TCG...defined in 2006 as a linear scaling of TCB having the approximate rate of TT. TCG is the time coordinate for the four dimensional geocentric coordinate

The kW power module evolution study: Executive summary

NASA Technical Reports Server (NTRS)

1979-01-01

Using the Marshall Space Flight Center 25 kW Power Module (PM) reference design as a point of departure, the study defined evolutionary growth paths to 100 kW and above. A recommended development approach and initial configurations were described. Specific hardware changes from the reference design are recommended for the initial PM configuration to ensure evolutionary growth, improved replicability, and reduced cost. Certain functional changes are also recommended to enhance system capabilities.

JPRS Report Science & Technology: Europe Economic Competitiveness.

DTIC Science & Technology

1992-11-19

Hungarian Telcos Order Finnish Systems Comptel Ltd of Helsinki is to supply turnkey systems to the private telephone companies founded by Kontrax and...requested. The transfer system of the Steinbeis Founda- tion is not just of interest to the companies because of the great amount of know-how it... performance of the network; Integrated EDI Archi- tecture and Layer Shell System , a reference architecture defining the interfact skeleton and

Backscatter calibration of high-frequency multibeam echosounder using a reference single-beam system, on natural seafloor

NASA Astrophysics Data System (ADS)

Eleftherakis, Dimitrios; Berger, Laurent; Le Bouffant, Naig; Pacault, Anne; Augustin, Jean-Marie; Lurton, Xavier

2018-06-01

The calibration of multibeam echosounders for backscatter measurements can be conducted efficiently and accurately using data from surveys over a reference natural area, implying appropriate measurements of the local absolute values of backscatter. Such a shallow area (20-m mean depth) has been defined and qualified in the Bay of Brest (France), and chosen as a reference area for multibeam systems operating at 200 and 300 kHz. The absolute reflectivity over the area was measured using a calibrated single-beam fishery echosounder (Simrad EK60) tilted at incidence angles varying between 0° and 60° with a step of 3°. This reference backscatter level is then compared to the average backscatter values obtained by a multibeam echosounder (here a Kongsberg EM 2040-D) at a close frequency and measured as a function of angle; the difference gives the angular bias applicable to the multibeam system for recorded level calibration. The method is validated by checking the single- and multibeam data obtained on other areas with sediment types different from the reference area.

CAD/CAM approach to improving industry productivity gathers momentum

NASA Technical Reports Server (NTRS)

Fulton, R. E.

1982-01-01

Recent results and planning for the NASA/industry Integrated Programs for Aerospace-Vehicle Design (IPAD) program for improving productivity with CAD/CAM methods are outlined. The industrial group work is being mainly done by Boeing, and progress has been made in defining the designer work environment, developing requirements and a preliminary design for a future CAD/CAM system, and developing CAD/CAM technology. The work environment was defined by conducting a detailed study of a reference design process, and key software elements for a CAD/CAM system have been defined, specifically for interactive design or experiment control processes. Further work is proceeding on executive, data management, geometry and graphics, and general utility software, and dynamic aspects of the programs being developed are outlined

An Interactive Computer-Aided Instructional Strategy and Assessment Methods for System Identification and Adaptive Control Laboratory

ERIC Educational Resources Information Center

Özbek, Necdet Sinan; Eker, Ilyas

2015-01-01

This study describes a set of real-time interactive experiments that address system identification and model reference adaptive control (MRAC) techniques. In constructing laboratory experiments that contribute to efficient teaching, experimental design and instructional strategy are crucial, but a process for doing this has yet to be defined. This…

Modeling and performance metrics of MIMO-SDM systems with different amplification schemes in the presence of mode-dependent loss.

PubMed

Antonelli, Cristian; Mecozzi, Antonio; Shtaif, Mark; Winzer, Peter J

2015-02-09

Mode-dependent loss (MDL) is a major factor limiting the achievable information rate in multiple-input multiple-output space-division multiplexed systems. In this paper we show that its impact on system performance, which we quantify in terms of the capacity reduction relative to a reference MDL-free system, may depend strongly on the operation of the inline optical amplifiers. This dependency is particularly strong in low mode-count systems. In addition, we discuss ways in which the signal-to-noise ratio of the MDL-free reference system can be defined and quantify the differences in the predicted capacity loss. Finally, we stress the importance of correctly accounting for the effect of MDL on the accumulation of amplification noise.

[Medical problems associated with the national reference pricing system in Hungary].

PubMed

Kerpel-Fronius, Sándor

2004-04-25

The author analyses the medical problems associated with the proposed reference pricing system prepared for the 2004 pharmaceutical price and reimbursement negotiations by the Hungarian National Health Insurance Fund (HNIF). In case of drugs containing identical active ingredients the author does not consider it acceptable that from the criteria of reference grouping bioequivalence was omitted, since bioequivalence is the basic clinical pharmacologic principle underlying the safe utilization of generic drugs. The proposal introduces in Hungary the therapeutic reference pricing for drugs belonging to the same ATC 5 level group, having different chemical structures but identical mechanisms of action. The products are listed according to their defined daily dose (DDD) and the arithmetic mean of the cheapest products giving together 50% market share is calculated. Each ATC 5 group has a given per cent reimbursement level and the fixed amount paid by the HNIF for all drugs in the group is defined as the given percentage of the mean price. This sum is reimbursed irrespective whether the products are patent protected or not, furthermore those drugs whose price is three times higher than the fixed mean price are excluded from the reimbursement system. As a result the patients' co-payment for the more expensive drugs will be significantly increased in the future. The basis of the therapeutic reference price is the assumption that the outcome of the treatment will be the same using drugs with the same mechanism of action. However, this assumption lacks valid scientific proof. According to the author, the proposed budget centric reference pricing system, which does not take into account the differing clinical pharmacologic profiles of the drugs, will significantly inhibit the use of new, innovative drugs, the establishment and continuous improvement of truly cost-effective patient care. Several alternative approaches are proposed for controlling drug budget. Finally the author recommends that a Committee should be established to develop a comprehensive proposal for the reorganization of the pricing and reimbursement system of the drugs available for general and/or hospital use, and for the follow-up of the health care effects of these measures.

Off-axis illumination direct-to-digital holography

DOEpatents

Thomas, Clarence E.; Price, Jeffery R.; Voelkl, Edgar; Hanson, Gregory R.

2004-06-08

Systems and methods are described for off-axis illumination direct-to-digital holography. A method of recording an off-axis illuminated spatially heterodyne hologram including spatially heterodyne fringes for Fourier analysis, includes: reflecting a reference beam from a reference mirror at a non-normal angle; reflecting an object beam from an object at an angle with respect to an optical axis defined by a focusing lens; focusing the reference beam and the object beam at a focal plane of a digital recorder to form the off-axis illuminated spatially heterodyne hologram including spatially heterodyne fringes for Fourier analysis; digitally recording the off-axis illuminated spatially heterodyne hologram including spatially heterodyne fringes for Fourier analysis; Fourier analyzing the recorded off-axis illuminated spatially heterodyne hologram including spatially heterodyne fringes by transforming axes of the recorded off-axis illuminated spatially heterodyne hologram including spatially heterodyne fringes in Fourier space to sit on top of a heterodyne carrier frequency defined as an angle between the reference beam and the object beam; applying a digital filter to cut off signals around an original origin; and then performing an inverse Fourier transform.

On a New Theory of the System of Reference

NASA Astrophysics Data System (ADS)

Kalanov, Temur Z.

2003-04-01

A new theory of the system of reference is suggested. It represents the new point of view which has arisen from the critical analysis of the foundations of physics (in particular, the theory of relativity and quantum mechanics), mathematics, cosmology and philosophy. The main idea following from the analysis is that the correct concept of system of reference represents a key to comprehension of many basic logic errors which are in modern physics. The starting point of the theory is represented by the philosophical (dialectical materialistic) principles, in particular, the gnosiological principle. (The gnosiological principle is briefly formulated as follows. The purpose of a science is to know the laws of the Nature. The law is a form of scientific knowledge of the essence and the phenomenon. The essence is the internal basis of the phenomenon, and the phenomenon is the manifestation of the essence. Human practice is a basis of knowledge and a criterion of truth). These principles lead to the following statements. (1) The reality is the dialectical unity of the opposites: the objective reality and the non-objective (subjective) reality. (2) The system mankind + means of knowledge belongs to the subjective reality and is called system of reference. In this wide sense, the system of reference is the universal informational gnostic basis (i.e. the system consisting of natural objects and processes, of constructed devices and instruments, of sum of human knowledge and skills) created and used by mankind for the purpose of knowledge of the world. (3) The opposites are bounds of each other. Hence, the principle of objectivity of the physical laws is formulated as follows: the objective physical laws must not contain mentions of system of reference (in particular, references to procedure of measurement or of calculation). (4) The main informational property of the unitary system set of researches physical objects + system of reference is that the system of reference determines (measures, calculates) the parameters of the subsystem set of researched physical objects (for example, the coordinates x_M, y_M, zM of the object M); the parameters characterize the system of reference (for example, the system of coordinates). (5) The main gnostic property of the unitary system set of researches physical objects + system of reference is that the system of reference defines (formulates) the physical laws (i.e. creates the theories); the physical laws characterize the system of reference. (6) The parameters which take on values independently of existence of the researched physical objects characterize the system of reference. For example, the clock C, a part of the system of reference S, determines (but it does not measure!) the time t_C; the time tC characterizes the clock C. If all clocks have been synchronized, the universal time tS characterizes the system of reference S. (7) Researched physical object M and a clock are mutually independent objects. Hence, the coordinates x_M, y_M, zM and the time tS are mutually independent parameters. (8) The informational one-to-one correspondence between motion of object M and physical clock-process in clock is established (is defined) by man. For example, it has a form: dx_M/dtS ≡ v_x_M. Consequences: (a) information about the world is an ordered information because the system of reference S is an ordered and universal system. This information is an objective one if it does not depend on a system of reference; (b) mathematical operations on physical quantities with the coordinates and with the time are allowed by the laws of logic because the set of researches physical objects + system of reference is a unitary system; (c) the principle of existence and of transformation of coordinates: there are no coordinates and no transformation of coordinates in general, and there exist the coordinates x_M, y_M, zM and transformation of the coordinates x_M, y_M, zM of the object M only; (d) the special and general theories of relativity are an erroneous theories because their foundations, firstly, do not satisfy the principle of objectivity of the physical laws, secondly, they contradict the principle of transformation of coordinates and, thirdly, they assume mutual dependence between the researched physical object and a clock (i.e. between coordinates and time); (e) quantum mechanics does not satisfy the principle of objectivity of the physical laws.

Anatomical parameterization for volumetric meshing of the liver

NASA Astrophysics Data System (ADS)

Vera, Sergio; González Ballester, Miguel A.; Gil, Debora

2014-03-01

A coordinate system describing the interior of organs is a powerful tool for a systematic localization of injured tissue. If the same coordinate values are assigned to specific anatomical landmarks, the coordinate system allows integration of data across different medical image modalities. Harmonic mappings have been used to produce parametric coordinate systems over the surface of anatomical shapes, given their flexibility to set values at specific locations through boundary conditions. However, most of the existing implementations in medical imaging restrict to either anatomical surfaces, or the depth coordinate with boundary conditions is given at sites of limited geometric diversity. In this paper we present a method for anatomical volumetric parameterization that extends current harmonic parameterizations to the interior anatomy using information provided by the volume medial surface. We have applied the methodology to define a common reference system for the liver shape and functional anatomy. This reference system sets a solid base for creating anatomical models of the patient's liver, and allows comparing livers from several patients in a common framework of reference.

Linguistics and Information Science

ERIC Educational Resources Information Center

Montgomery, Christine A.

1972-01-01

This paper defines the relationship between linguistics and information science in terms of a common interest in natural language. The concept of a natural language information system is introduced as a framework for reviewing automated language processing efforts by computational linguists and information scientists. (96 references) (Author)

Social Partnership in Accrediting Lithuanian VET Qualifications

ERIC Educational Resources Information Center

Tutlys, Vidmantas; Kaminskiene, Lina

2008-01-01

This article examines social partnership in accrediting qualifications in Lithuania. It defines the factors influencing social partnership and surveys future development perspectives, referring to the creation and implementation of the national qualifications system in Lithuania. Social partnership in qualifications accreditation is regarded as a…

Reference Architecture Model Enabling Standards Interoperability.

PubMed

Blobel, Bernd

2017-01-01

Advanced health and social services paradigms are supported by a comprehensive set of domains managed by different scientific disciplines. Interoperability has to evolve beyond information and communication technology (ICT) concerns, including the real world business domains and their processes, but also the individual context of all actors involved. So, the system must properly reflect the environment in front and around the computer as essential and even defining part of the health system. This paper introduces an ICT-independent system-theoretical, ontology-driven reference architecture model allowing the representation and harmonization of all domains involved including the transformation into an appropriate ICT design and implementation. The entire process is completely formalized and can therefore be fully automated.

Crew system dynamics - Combining humans and automation

NASA Technical Reports Server (NTRS)

Connors, Mary

1989-01-01

Some of the human factor issues involved in effectively combining human and automated systems are examined with particular reference to spaceflights. The concepts of the crew system and crew systems dynamics are defined, and the present status of crew systems is summarized. The possibilities and potential problems aasociated with the use of automated systems are discussed, as are unique capabilities and possible errors introduced by human participants. It is emphasized that the true integration of human and automated systems must allow for the characteristics of both.

Defining the cortical visual systems: "what", "where", and "how"

NASA Technical Reports Server (NTRS)

Creem, S. H.; Proffitt, D. R.; Kaiser, M. K. (Principal Investigator)

2001-01-01

The visual system historically has been defined as consisting of at least two broad subsystems subserving object and spatial vision. These visual processing streams have been organized both structurally as two distinct pathways in the brain, and functionally for the types of tasks that they mediate. The classic definition by Ungerleider and Mishkin labeled a ventral "what" stream to process object information and a dorsal "where" stream to process spatial information. More recently, Goodale and Milner redefined the two visual systems with a focus on the different ways in which visual information is transformed for different goals. They relabeled the dorsal stream as a "how" system for transforming visual information using an egocentric frame of reference in preparation for direct action. This paper reviews recent research from psychophysics, neurophysiology, neuropsychology and neuroimaging to define the roles of the ventral and dorsal visual processing streams. We discuss a possible solution that allows for both "where" and "how" systems that are functionally and structurally organized within the posterior parietal lobe.

Extraterrestrial processing and manufacturing of large space systems, volume 1, chapters 1-6

NASA Technical Reports Server (NTRS)

Miller, R. H.; Smith, D. B. S.

1979-01-01

Space program scenarios for production of large space structures from lunar materials are defined. The concept of the space manufacturing facility (SMF) is presented. The manufacturing processes and equipment for the SMF are defined and the conceptual layouts are described for the production of solar cells and arrays, structures and joints, conduits, waveguides, RF equipment radiators, wire cables, and converters. A 'reference' SMF was designed and its operation requirements are described.

A Concept Analysis of Systems Thinking.

PubMed

Stalter, Ann M; Phillips, Janet M; Ruggiero, Jeanne S; Scardaville, Debra L; Merriam, Deborah; Dolansky, Mary A; Goldschmidt, Karen A; Wiggs, Carol M; Winegardner, Sherri

2017-10-01

This concept analysis, written by the National Quality and Safety Education for Nurses (QSEN) RN-BSN Task Force, defines systems thinking in relation to healthcare delivery. A review of the literature was conducted using five databases with the keywords "systems thinking" as well as "nursing education," "nursing curriculum," "online," "capstone," "practicum," "RN-BSN/RN to BSN," "healthcare organizations," "hospitals," and "clinical agencies." Only articles that focused on systems thinking in health care were used. The authors identified defining attributes, antecedents, consequences, and empirical referents of systems thinking. Systems thinking was defined as a process applied to individuals, teams, and organizations to impact cause and effect where solutions to complex problems are accomplished through collaborative effort according to personal ability with respect to improving components and the greater whole. Four primary attributes characterized systems thinking: dynamic system, holistic perspective, pattern identification, and transformation. Using the platform provided in this concept analysis, interprofessional practice has the ability to embrace planned efforts to improve critically needed quality and safety initiatives across patients' lifespans and all healthcare settings. © 2016 Wiley Periodicals, Inc.

Biological Movement and Laws of Physics.

PubMed

Latash, Mark L

2017-07-01

Living systems may be defined as systems able to organize new, biology-specific, laws of physics and modify their parameters for specific tasks. Examples include the force-length muscle dependence mediated by the stretch reflex, and the control of movements with modification of the spatial referent coordinates for salient performance variables. Low-dimensional sets of referent coordinates at a task level are transformed to higher-dimensional sets at lower hierarchical levels in a way that ensures stability of performance. Stability of actions can be controlled independently of the actions (e.g., anticipatory synergy adjustments). Unintentional actions reflect relaxation processes leading to drifts of corresponding referent coordinates in the absence of changes in external load. Implications of this general framework for movement disorders, motor development, motor skill acquisition, and even philosophy are discussed.

Development of NASA's Space Communications and Navigation Test Bed Aboard ISS to Investigate SDR, On-Board Networking and Navigation Technologies

NASA Technical Reports Server (NTRS)

Reinhart, Richard C.; Kacpura, Thomas J.; Johnson, Sandra K.; Lux, James P.

2010-01-01

NASA is developing an experimental flight payload (referred to as the Space Communication and Navigation (SCAN) Test Bed) to investigate software defined radio (SDR), networking, and navigation technologies, operationally in the space environment. The payload consists of three software defined radios each compliant to NASA s Space Telecommunications Radio System Architecture, a common software interface description standard for software defined radios. The software defined radios are new technology developments underway by NASA and industry partners. Planned for launch in early 2012, the payload will be externally mounted to the International Space Station truss and conduct experiments representative of future mission capability.

The Design, Development and Testing of Complex Avionics Systems: Conference Proceedings Held at the Avionics Panel Symposium in Las Vegas, Nevada on 27 April-1 May 1987

DTIC Science & Technology

1987-12-01

Normally, the system is decomposed into manageable parts with accurately defined interfaces. By rigidly controlling this process, aerospace companies have...Reference A CHANGE IN SYSTEM DESIGN EMPHASIS: FROM MACHINE TO MAN by M.L.Metersky and J.L.Ryder 16 SESSION I1 - MANAGING THE FUl URE SYSTEM DESIGN...PROCESS MANAGING ADVANCED AVIONIC SYSTEM DESIGN by P.Simons 17 ERGONOMIE PSYCHOSENSORIELLE DES COCKPITS, INTERET DES SYSTEMES INFORMATIQUES INTELLIGENTS

Energy and environmental evaluation of combined cooling heating and power system

NASA Astrophysics Data System (ADS)

Bugaj, Andrzej

2017-11-01

The paper addresses issues involving problems of implementing combined cooling, heating and power (CCHP) system to industrial facility with well-defined demand profiles of cooling, heating and electricity. The application of CCHP system in this particular industrial facility is being evaluated by comparison with the reference system that consists of three conventional methods of energy supply: (a) electricity from external grid, (b) heat from gas-fired boilers and (c) cooling from vapour compression chillers run by electricity from the grid. The CCHP system scenario is based on the combined heat and power (CHP) plant with gas turbine-compressor arrangement and water/lithium bromide absorption chiller of a single-effect type. Those two scenarios are analysed in terms of annual primary energy usage as well as emissions of CO2. The results of the analysis show an extent of primary energy savings of the CCHP system in comparison with the reference system. Furthermore, the environmental impact of the CCHP usage, in the form of greenhouse gases emission reductions, compares quite favourably with the reference conventional option.

The Modulated Annual Cycle: An Alternative Reference Frame for Climate Anomalies

NASA Astrophysics Data System (ADS)

Wu, Z.

2007-12-01

In climate science, an anomaly is the deviation of a quantity from its annual cycle (AC). There are many ways to define annual cycle. Traditionally, the annual cycle is taken to be an exact repetition of itself year after year. This stationary annual cycle may not reflect well the intrinsic nonlinearity of the climate system, especially under external forcing. In this study, we have reexamined the reference frame for anomalies by reexamining the annual cycle. We propose an alternative reference frame, the modulated annual cycle (MAC) that allows the annual cycle to change from year to year, for defining anomalies. In order for this alternative reference frame to be useful, we need to be able to define the instantaneous annual cycle. We therefore also introduce a new method to extract the MAC from climatic data. In the presence of an MAC, modulated in both amplitude and frequency, we can then define an alternative version of an anomaly, this time with respect to the instantaneous MAC rather than a permanent and unchanging AC. Based on this alternative definition of anomalies, we reexamine some familiar physical processes: in particular, the sea surface temperature (SST) reemergence and the ENSO phase locking to the annual cycle. We find that the re-emergence mechanism may be alternatively interpreted as an explanation of the change of the annual cycle instead of the interannual to interdecadal persistence of SST anomalies. We also find that the ENSO phase locking can largely be attributed to the residual annual cycle (the difference of the MAC and the corresponding traditional annual cycle) contained in the traditional anomaly, and, therefore, can be alternatively interpreted as a part of the annual cycle phase locked to the annual cycle itself. Two additional examples are also presented of the implications of using a MAC against which to define anomalies. We show that using MAC as a reference framework for anomaly can bypass the difficulty brought by concepts such as "decadal variability of summer (or winter) climate" for understanding the low-frequency variability of the climate system. We also point out the drawbacks related to the stationary assumption in previous studies of extreme weather and climate and propose instead the appropriateness of choosing a non-stationary framework to study extreme weather and climate events. The concept of an amplitude and frequency modulated annual cycle, a method to extract it, and its implications for the interpretation of physical processes, all may contribute potentially to a more consistent and fruitful way of examining past and future climate variability and change.

The modulated annual cycle: an alternative reference frame for climate anomalies

NASA Astrophysics Data System (ADS)

Wu, Zhaohua; Schneider, Edwin K.; Kirtman, Ben P.; Sarachik, E. S.; Huang, Norden E.; Tucker, Compton J.

2008-12-01

In climate science, an anomaly is the deviation of a quantity from its annual cycle. There are many ways to define annual cycle. Traditionally, this annual cycle is taken to be an exact repeat of itself year after year. This stationary annual cycle may not reflect well the intrinsic nonlinearity of the climate system, especially under external forcing. In this paper, we re-examine the reference frame for anomalies by re-examining the annual cycle. We propose an alternative reference frame for climate anomalies, the modulated annual cycle (MAC) that allows the annual cycle to change from year to year, for defining anomalies. In order for this alternative reference frame to be useful, we need to be able to define the instantaneous annual cycle: we therefore also introduce a new method to extract the MAC from climatic data. In the presence of a MAC, modulated in both amplitude and frequency, we can then define an alternative version of an anomaly, this time with respect to the instantaneous MAC rather than a permanent and unchanging AC. Based on this alternative definition of anomalies, we re-examine some familiar physical processes: in particular SST re-emergence and ENSO phase locking to the annual cycle. We find that the re-emergence mechanism may be alternatively interpreted as an explanation of the change of the annual cycle instead of an explanation of the interannual to interdecadal persistence of SST anomalies. We also find that the ENSO phase locking can largely be attributed to the residual annual cycle (the difference of the MAC and the corresponding traditional annual cycle) contained in the traditional anomaly, and, therefore, can be alternatively interpreted as a part of the annual cycle phase locked to the annual cycle itself. In addition to the examples of reinterpretation of physics of well known climate phenomena, we also present an example of the implications of using a MAC against which to define anomalies. We show that using MAC as a reference framework for anomaly can bypass the difficulty brought by concepts such as “decadal variability of summer (or winter) climate” for understanding the low-frequency variability of the climate system. The concept of an amplitude and frequency modulated annual cycle, a method to extract it, and its implications for the interpretation of physical processes, all may contribute potentially to a more consistent and fruitful way of examining past and future climate variability and change.

Properties of coupled-cluster equations originating in excitation sub-algebras

NASA Astrophysics Data System (ADS)

Kowalski, Karol

2018-03-01

In this paper, we discuss properties of single-reference coupled cluster (CC) equations associated with the existence of sub-algebras of excitations that allow one to represent CC equations in a hybrid fashion where the cluster amplitudes associated with these sub-algebras can be obtained by solving the corresponding eigenvalue problem. For closed-shell formulations analyzed in this paper, the hybrid representation of CC equations provides a natural way for extending active-space and seniority number concepts to provide an accurate description of electron correlation effects. Moreover, a new representation can be utilized to re-define iterative algorithms used to solve CC equations, especially for tough cases defined by the presence of strong static and dynamical correlation effects. We will also explore invariance properties associated with excitation sub-algebras to define a new class of CC approximations referred to in this paper as the sub-algebra-flow-based CC methods. We illustrate the performance of these methods on the example of ground- and excited-state calculations for commonly used small benchmark systems.

Evolution of Timescales from Astronomy to Physical Metrology

DTIC Science & Technology

2011-07-20

2000 [7] recommended the use of the ‘non-rotating origin’ both in the Geocentric Celestial Reference System (GCRS) and the International Terrestrial...timescale defined in a geocentric reference frame with the SI second as realized on the rotating geoid as the scale unit’ [30, 31]. This meant that it was...of the new timescale for apparent geocentric ephemerides, will be 1977 January 1d.0003725 (1d 00h 00m 32.184s) exactly. (b) The unit of this timescale

AOIPS data base management systems support for GARP data sets

NASA Technical Reports Server (NTRS)

Gary, J. P.

1977-01-01

A data base management system is identified, developed to provide flexible access to data sets produced by GARP during its data systems tests. The content and coverage of the data base are defined and a computer-aided, interactive information storage and retrieval system, implemented to facilitate access to user specified data subsets, is described. The computer programs developed to provide the capability were implemented on the highly interactive, minicomputer-based AOIPS and are referred to as the data retrieval system (DRS). Implemented as a user interactive but menu guided system, the DRS permits users to inventory the data tape library and create duplicate or subset data sets based on a user selected window defined by time and latitude/longitude boundaries. The DRS permits users to select, display, or produce formatted hard copy of individual data items contained within the data records.

Evaluating the Impact of Drug Trafficking Organizations on the Stability of the Mexican State

DTIC Science & Technology

2010-06-11

Mexican state is unlikely to fail as state failure is defined, but the Mexican government is likely to return to a one party system under which drug...College or any other governmental agency. (References to this study should include the foregoing statement.) iv ABSTRACT EVALUATING THE IMPACT OF...security of the U.S. The primary conclusion drawn is that the Mexican state is unlikely to fail as state failure is defined, but the Mexican government

Establishing references for gene expression analyses by RT-qPCR in Theobroma cacao tissues.

PubMed

Pinheiro, T T; Litholdo, C G; Sereno, M L; Leal, G A; Albuquerque, P S B; Figueira, A

2011-11-17

Lack of continuous progress in Theobroma cacao (Malvaceae) breeding, especially associated with seed quality traits, requires more efficient selection methods based on genomic information. Reverse transcript quantitative PCR (RT-qPCR) has become the method of choice for gene expression analysis, but relative expression analysis requires various reference genes, which must be stable across various biological conditions. We sought suitable reference genes for various tissues of cacao, especially developing seeds. Ten potential reference genes were analyzed for stability at various stages of embryo development, leaves, stems, roots, flowers, and pod epicarp; seven of them were also evaluated in shoot tips treated either with hormones (salicylate; ethefon; methyl-jasmonate) or after inoculation with the fungus Moniliophthora perniciosa (Marasmiaceae sensu lato). For developing embryos, the three most stable genes were actin (ACT), polyubiquitin (PUB), and ribosomal protein L35 (Rpl35). In the analyses of various tissues, the most stable genes were malate dehydrogenase (MDH), glyceraldehyde 3-phosphate dehydrogenase (GAPDH), and acyl-carrier protein B (ACP B). GAPDH, MDH and tubulin (TUB) were the most appropriate for normalization when shoot apexes were treated with hormones, while ACT, TUB and Rpl35 were the most appropriate after inoculation with M. perniciosa. We conclude that for each plant system and biological or ontogenetical condition, there is a need to define suitable reference genes. This is the first report to define reference genes for expression studies in cacao.

InSAR datum connection using GNSS-augmented radar transponders

NASA Astrophysics Data System (ADS)

Mahapatra, Pooja; der Marel, Hans van; van Leijen, Freek; Samiei-Esfahany, Sami; Klees, Roland; Hanssen, Ramon

2018-01-01

Deformation estimates from Interferometric Synthetic Aperture Radar (InSAR) are relative: they form a `free' network referred to an arbitrary datum, e.g. by assuming a reference point in the image to be stable. However, some applications require `absolute' InSAR estimates, i.e. expressed in a well-defined terrestrial reference frame, e.g. to compare InSAR results with those of other techniques. We propose a methodology based on collocated InSAR and Global Navigation Satellite System (GNSS) measurements, achieved by rigidly attaching phase-stable millimetre-precision compact active radar transponders to GNSS antennas. We demonstrate this concept through a simulated example and practical case studies in the Netherlands.

Quantum mechanics in noninertial reference frames: Relativistic accelerations and fictitious forces

NASA Astrophysics Data System (ADS)

Klink, W. H.; Wickramasekara, S.

2016-06-01

One-particle systems in relativistically accelerating reference frames can be associated with a class of unitary representations of the group of arbitrary coordinate transformations, an extension of the Wigner-Bargmann definition of particles as the physical realization of unitary irreducible representations of the Poincaré group. Representations of the group of arbitrary coordinate transformations become necessary to define unitary operators implementing relativistic acceleration transformations in quantum theory because, unlike in the Galilean case, the relativistic acceleration transformations do not themselves form a group. The momentum operators that follow from these representations show how the fictitious forces in noninertial reference frames are generated in quantum theory.

Ecoliteracy and a Place-Based Pedagogy: Expanding Latin@ Students' Critical Understanding of the Reciprocity between Sociocultural Systems and Ecosystems in the US-Mexico Border Region

ERIC Educational Resources Information Center

Gutierrez, Kristina A.

2012-01-01

This dissertation proposes a place-based theoretical and methodological framework, informed by concepts of ecology, multimodality, and activity systems. I apply this framework of ecoliteracy as it is defined within the interdisciplinary contexts of rhetoric and composition, linguistics, and Chicana/o studies. Ecoliteracy refers to individuals'…

Positioning system for single or multi-axis sensitive instrument calibration and calibration system for use therewith

NASA Technical Reports Server (NTRS)

Finley, Tom D. (Inventor); Parker, Peter A. (Inventor)

2008-01-01

A positioning and calibration system are provided for use in calibrating a single or multi axis sensitive instrument, such as an inclinometer. The positioning system includes a positioner that defines six planes of tangential contact. A mounting region within the six planes is adapted to have an inclinometer coupled thereto. The positioning system also includes means for defining first and second flat surfaces that are approximately perpendicular to one another with the first surface adapted to be oriented relative to a local or induced reference field of interest to the instrument being calibrated, such as a gravitational vector. The positioner is positioned such that one of its six planes tangentially rests on the first flat surface and another of its six planes tangentially contacts the second flat surface. A calibration system is formed when the positioning system is used with a data collector and processor.

Music: Creativity and Structure Transitions

NASA Astrophysics Data System (ADS)

Pietrocini, Emanuela

Music, compared to other complex forms of representation, is fundamentally characterized by constant evolution and a dynamic succession of structure reference models. This is without taking into account historical perspective, the analysis of forms and styles, or questions of a semantic nature; the observation rather refers to the phenomenology of the music system. The more abstract a compositional model, the greater the number and frequency of variables that are not assimilated to the reference structure; this "interference" which happens more often than not in an apparently casual manner, modifies the creative process to varying but always substantial degrees: locally, it produces a disturbance in perceptive, formal and structural parameters, resulting more often than not in a synaesthetic experience; globally, on the other hand, it defines the terms of a transition to a new state, in which the relations between elements and components modify the behavior of the entire system from which they originated. It is possible to find examples of this phenomenon in the whole range of musical production, in particular in improvisations, in the use of the Basso Continuo, and in some contrapuntal works of the baroque period, music whose temporal dimension can depart from the limits of mensurability and symmetry to define an open compositional environment in continuous evolution.

49 CFR 571.104 - Standard No. 104; Windshield wiping and washing systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., SAE Aerospace-Automotive Drawing Standards, September 1963. Glazing surface reference line means the... “W116”, as defined in section E, Ground Vehicle Practice, SAE Aerospace-Automotive Drawing Standards... Practice, SAE Aerospace-Automotive Drawing Standards, September 1963. 95 percent eye range contour means...

Economic Modeling as a Component of Academic Strategic Planning.

ERIC Educational Resources Information Center

MacKinnon, Joyce; Sothmann, Mark; Johnson, James

2001-01-01

Computer-based economic modeling was used to enable a school of allied health to define outcomes, identify associated costs, develop cost and revenue models, and create a financial planning system. As a strategic planning tool, it assisted realistic budgeting and improved efficiency and effectiveness. (Contains 18 references.) (SK)

Building software tools to help contextualize and interpret monitoring data

USDA-ARS?s Scientific Manuscript database

Even modest monitoring efforts at landscape scales produce large volumes of data.These are most useful if they can be interpreted relative to land potential or other similar sites. However, for many ecological systems reference conditions may not be defined or are poorly described, which hinders und...

Learning Portfolio Analysis and Mining for SCORM Compliant Environment

ERIC Educational Resources Information Center

Su, Jun-Ming; Tseng, Shian-Shyong; Wang, Wei; Weng, Jui-Feng; Yang, Jin Tan David; Tsai, Wen-Nung

2006-01-01

With vigorous development of the Internet, e-learning system has become more and more popular. Sharable Content Object Reference Model (SCORM) 2004 provides the Sequencing and Navigation (SN) Specification to define the course sequencing behavior, control the sequencing, selecting and delivering of course, and organize the content into a…

Virtual Reality: Is It for Real?

ERIC Educational Resources Information Center

Dowding, Tim J.

1994-01-01

Defines virtual reality and describes its application to psychomotor skills training. A description of a system that could be used to teach a college course in physical therapy, including the use of miniature computer workstation, sensory gloves, a programmable mannequin, and other existing technology, is provided. (Contains 10 references.) (KRN)

The Current Status and Tendency of China Millimeter Coordinate Frame Implementation and Maintenance

NASA Astrophysics Data System (ADS)

Cheng, P.; Cheng, Y.; Bei, J.

2017-12-01

China Geodetic Coordinate System 2000 (CGCS2000) was first officially declared as the national standard coordinate system on July 1, 2008. This reference frame was defined in the ITRF97 frame at epoch 2000.0 and included 2600 GPS geodetic control points. The paper discusses differences between China Geodetic Coordinate System 2000 (CGCS2000) and later updated ITRF versions, such as ITRF2014,in terms of technical implementation and maintenance. With the development of the Beidou navigation satellite system, especially third generation of BDS with signal global coverage in the future, and with progress of space geodetic technology, it is possible for us to establish a global millimeter-level reference frame based on space geodetic technology including BDS. The millimeter reference frame implementation concerns two factors: 1) The variation of geocenter motion estimation, and 2) the site nonlinear motion modeling. In this paper, the geocentric inversion methods are discussed and compared among results derived from various technical methods. Our nonlinear site movement modeling focuses on singular spectrum analysis method, which is of apparent advantages over earth physical effect modeling. All presented in the paper expected to provide reference to our future CGCS2000 maintenance.

Direct and Absolute Quantification of over 1800 Yeast Proteins via Selected Reaction Monitoring*

PubMed Central

Lawless, Craig; Holman, Stephen W.; Brownridge, Philip; Lanthaler, Karin; Harman, Victoria M.; Watkins, Rachel; Hammond, Dean E.; Miller, Rebecca L.; Sims, Paul F. G.; Grant, Christopher M.; Eyers, Claire E.; Beynon, Robert J.

2016-01-01

Defining intracellular protein concentration is critical in molecular systems biology. Although strategies for determining relative protein changes are available, defining robust absolute values in copies per cell has proven significantly more challenging. Here we present a reference data set quantifying over 1800 Saccharomyces cerevisiae proteins by direct means using protein-specific stable-isotope labeled internal standards and selected reaction monitoring (SRM) mass spectrometry, far exceeding any previous study. This was achieved by careful design of over 100 QconCAT recombinant proteins as standards, defining 1167 proteins in terms of copies per cell and upper limits on a further 668, with robust CVs routinely less than 20%. The selected reaction monitoring-derived proteome is compared with existing quantitative data sets, highlighting the disparities between methodologies. Coupled with a quantification of the transcriptome by RNA-seq taken from the same cells, these data support revised estimates of several fundamental molecular parameters: a total protein count of ∼100 million molecules-per-cell, a median of ∼1000 proteins-per-transcript, and a linear model of protein translation explaining 70% of the variance in translation rate. This work contributes a “gold-standard” reference yeast proteome (including 532 values based on high quality, dual peptide quantification) that can be widely used in systems models and for other comparative studies. PMID:26750110

The Gaia inertial reference frame and the tilting of the Milky Way disk

DOE Office of Scientific and Technical Information (OSTI.GOV)

Perryman, Michael; Spergel, David N.; Lindegren, Lennart, E-mail: mac.perryman@gmail.com

2014-07-10

While the precise relationship between the Milky Way disk and the symmetry planes of the dark matter halo remains somewhat uncertain, a time-varying disk orientation with respect to an inertial reference frame seems probable. Hierarchical structure formation models predict that the dark matter halo is triaxial and tumbles with a characteristic rate of ∼2 rad H{sub 0}{sup −1} (∼30 μas yr{sup –1}). These models also predict a time-dependent accretion of gas, such that the angular momentum vector of the disk should be misaligned with that of the halo. These effects, as well as tidal effects of the LMC, will resultmore » in the rotation of the angular momentum vector of the disk population with respect to the quasar reference frame. We assess the accuracy with which the positions and proper motions from Gaia can be referred to a kinematically non-rotating system, and show that the spin vector of the transformation from any rigid self-consistent catalog frame to the quasi-inertial system defined by quasars should be defined to better than 1 μas yr{sup –1}. Determination of this inertial frame by Gaia will reveal any signature of the disk orientation varying with time, improve models of the potential and dynamics of the Milky Way, test theories of gravity, and provide new insights into the orbital evolution of the Sagittarius dwarf galaxy and the Magellanic Clouds.« less

Air Force Global Weather Central System Architecture Study. Final System/Subsystem Summary Report. Volume 8. System Specification

DTIC Science & Technology

1976-03-01

Service , CSE, Scott AFB, IL 62225. aws, usaf ltr dtd 8 jul 1976 >- a. CD SYSTEM DEVELOPMENT CORPORATION 1/ 2500 Colorado Avenue Santa Monica...Government Agen-TfAf* 17 MAR 1976 cies only. Other requests for this document ’-^ must be referred to Air Weather Service /CSi^,, Scott Air Force...Air Force Communica- tions Service must be clear’y defined. The appropriate Air Force Conmunications Service Agency should be responsible for the

Process-based reference conditions: An alternative approach for managed river systems

NASA Astrophysics Data System (ADS)

Grams, P.; Melis, T.; Wright, S.; Schmidt, J.; Topping, D.

2008-12-01

Physical reference conditions, whether based on historic information or the condition of nearby less impaired systems, provide necessary information that contributes to an assessment of stream condition and the nature of channel transformation. In many cases, however, the utility of this traditional 'reference' approach may end at the assessment stage and not be applicable to establishing and implementing restoration goals. Ongoing impacts such as continued existence of an upstream dam or the persistence of invasive vegetation may render restoration based on a physical reference infeasible. In these circumstances, an alternative approach is to identify and describe reference processes in place of physical reference conditions. This is the case for the Colorado River where large dams, a commitment to hydropower production, and legal mandates for regional distribution and off- channel consumption of water greatly reduce the relevance of historical conditions in setting goals for rehabilitation. In this setting, two strategies are available for setting reference conditions. One is maintenance of post-dam sediment mass balance, which attempts to ensure that the channel does not continue to degrade or aggrade and that riverine habitats do not continue to diverge from their historical condition. Post- dam sediment mass balance can be quantified at a reconnaissance or project scale. The second strategy is to define key processes that maintain the native ecosystem. These processes may, or may not, be consistent with maintenance of sediment mass balance, but they may be key to rejuvenation of spawning and rearing habitats, maintenance of historical ranges of temperature and turbidity, maintenance of a sustainable food base for the native aquatic community, or maintaining other riverine resources. Both strategies require careful monitoring of processes (e.g. sediment flux), which may add considerably to the cost and complexity of a monitoring program. An additional challenge in adopting the second strategy is that it is difficult to define when a process is adequately restored, since many ecosystem processes collectively limit recovery of populations of native communities.

Unification of height systems in the frame of GGOS

NASA Astrophysics Data System (ADS)

Sánchez, Laura

2015-04-01

Most of the existing vertical reference systems do not fulfil the accuracy requirements of modern Geodesy. They refer to local sea surface levels, are stationary (do not consider variations in time), realize different physical height types (orthometric, normal, normal-orthometric, etc.), and their combination in a global frame presents uncertainties at the metre level. To provide a precise geodetic infrastructure for monitoring the Earth system, the Global Geodetic Observing System (GGOS) of the International Association of Geodesy (IAG), promotes the standardization of the height systems worldwide. The main purpose is to establish a global gravity field-related vertical reference system that (1) supports a highly-precise (at cm-level) combination of physical and geometric heights worldwide, (2) allows the unification of all existing local height datums, and (3) guarantees vertical coordinates with global consistency (the same accuracy everywhere) and long-term stability (the same order of accuracy at any time). Under this umbrella, the present contribution concentrates on the definition and realization of a conventional global vertical reference system; the standardization of the geodetic data referring to the existing height systems; and the formulation of appropriate strategies for the precise transformation of the local height datums into the global vertical reference system. The proposed vertical reference system is based on two components: a geometric component consisting of ellipsoidal heights as coordinates and a level ellipsoid as the reference surface, and a physical component comprising geopotential numbers as coordinates and an equipotential surface defined by a conventional W0 value as the reference surface. The definition of the physical component is based on potential parameters in order to provide reference to any type of physical heights (normal, orthometric, etc.). The conversion of geopotential numbers into metric heights and the modelling of the reference surface (geoid or quasigeoid determination) are considered as steps of the realization. The vertical datum unification strategy is based on (1) the physical connection of height datums to determine their discrepancies, (2) joint analysis of satellite altimetry and tide gauge records to determine time variations of sea level at reference tide gauges, (3) combination of geometrical and physical heights in a well-distributed and high-precise reference frame to estimate the relationship between the individual vertical levels and the global one, and (4) analysis of GNSS time series at reference tide gauges to separate crustal movements from sea level changes. The final vertical transformation parameters are provided by the common adjustment of the observation equations derived from these methods.

11 CFR 109.21 - What is a “coordinated communication”?

Code of Federal Regulations, 2012 CFR

2012-01-01

... 100.29. (2) A public communication, as defined in 11 CFR 100.26, that disseminates, distributes, or... public communication, as defined in 11 CFR 100.26, that expressly advocates, as defined in 11 CFR 100.22... section: (i) References to House and Senate candidates. The public communication refers to a clearly...

11 CFR 109.21 - What is a “coordinated communication”?

Code of Federal Regulations, 2014 CFR

2014-01-01

... 100.29. (2) A public communication, as defined in 11 CFR 100.26, that disseminates, distributes, or... public communication, as defined in 11 CFR 100.26, that expressly advocates, as defined in 11 CFR 100.22... section: (i) References to House and Senate candidates. The public communication refers to a clearly...

11 CFR 109.21 - What is a “coordinated communication”?

Code of Federal Regulations, 2011 CFR

2011-01-01

... 100.29. (2) A public communication, as defined in 11 CFR 100.26, that disseminates, distributes, or... public communication, as defined in 11 CFR 100.26, that expressly advocates, as defined in 11 CFR 100.22... section: (i) References to House and Senate candidates. The public communication refers to a clearly...

11 CFR 109.21 - What is a “coordinated communication”?

Code of Federal Regulations, 2013 CFR

2013-01-01

... 100.29. (2) A public communication, as defined in 11 CFR 100.26, that disseminates, distributes, or... public communication, as defined in 11 CFR 100.26, that expressly advocates, as defined in 11 CFR 100.22... section: (i) References to House and Senate candidates. The public communication refers to a clearly...

User Manual for the AZ-101 Data Acquisition System (AS-101 DAS)

DOE Office of Scientific and Technical Information (OSTI.GOV)

BRAYTON, D.D.

2000-02-17

User manual for the TK AZ-101 Waste Retrieval System Data Acquisition System. The purpose of this document is to describe use of the AZ-101 Data Acquisition System (AZ-101 DAS). The AZ-101 DAS is provided to fulfill the requirements for data collection and monitoring as defined in Letters of Instruction (LOI) from Numatec Hanford Corporation (NHC) to Fluor Federal Services (FFS). For a complete description of the system, including design, please refer to the AZ-101 DAS System Description document, RPP-5572.

Networked differential GPS system

NASA Technical Reports Server (NTRS)

Sheynblat, Leonid (Inventor); Kalafus, Rudolph M. (Inventor); Loomis, Peter V. W. (Inventor); Mueller, K. Tysen (Inventor)

1994-01-01

An embodiment of the present invention relates to a worldwide network of differential GPS reference stations (NDGPS) that continually track the entire GPS satellite constellation and provide interpolations of reference station corrections tailored for particular user locations between the reference stations Each reference station takes real-time ionospheric measurements with codeless cross-correlating dual-frequency carrier GPS receivers and computes real-time orbit ephemerides independently. An absolute pseudorange correction (PRC) is defined for each satellite as a function of a particular user's location. A map of the function is constructed, with iso-PRC contours. The network measures the PRCs at a few points, so-called reference stations and constructs an iso-PRC map for each satellite. Corrections are interpolated for each user's site on a subscription basis. The data bandwidths are kept to a minimum by transmitting information that cannot be obtained directly by the user and by updating information by classes and according to how quickly each class of data goes stale given the realities of the GPS system. Sub-decimeter-level kinematic accuracy over a given area is accomplished by establishing a mini-fiducial network.

Design and development of pressure and repressurization purge system for reusable space shuttle multilayer insulation system

NASA Technical Reports Server (NTRS)

1971-01-01

Preliminary design and analysis of purge system concepts and purge subsystem approaches are defined and evaluated. Acceptable purge subsystem approaches were combined into four predesign layouts which are presented for comparison and evaluation. Two predesigns were selected for further detailed design and evaluation for eventual selection of the best design for a full scale test configuration. An operation plan is included as an appendix for reference to shuttle-oriented operational parameters.

Corrosion engineering in the utilization of the Raft River geothermal resource

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, R.L.

1976-08-01

The economic impact of corrosion and the particular problems of corrosion in the utilization of geothermal energy resources are noted. Corrosion is defined and the parameters that control corrosion in geothermal systems are discussed. A general background of corrosion is presented in the context of the various forms of corrosion, in relation to the Raft River geothermal system. A basic reference for mechanical design engineers involved in the design of geothermal energy recovery systems is provided.

From scenarios to domain models: processes and representations

NASA Astrophysics Data System (ADS)

Haddock, Gail; Harbison, Karan

1994-03-01

The domain specific software architectures (DSSA) community has defined a philosophy for the development of complex systems. This philosophy improves productivity and efficiency by increasing the user's role in the definition of requirements, increasing the systems engineer's role in the reuse of components, and decreasing the software engineer's role to the development of new components and component modifications only. The scenario-based engineering process (SEP), the first instantiation of the DSSA philosophy, has been adopted by the next generation controller project. It is also the chosen methodology of the trauma care information management system project, and the surrogate semi-autonomous vehicle project. SEP uses scenarios from the user to create domain models and define the system's requirements. Domain knowledge is obtained from a variety of sources including experts, documents, and videos. This knowledge is analyzed using three techniques: scenario analysis, task analysis, and object-oriented analysis. Scenario analysis results in formal representations of selected scenarios. Task analysis of the scenario representations results in descriptions of tasks necessary for object-oriented analysis and also subtasks necessary for functional system analysis. Object-oriented analysis of task descriptions produces domain models and system requirements. This paper examines the representations that support the DSSA philosophy, including reference requirements, reference architectures, and domain models. The processes used to create and use the representations are explained through use of the scenario-based engineering process. Selected examples are taken from the next generation controller project.

76 FR 16712 - Participation by Religious Organizations in USAID Programs

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-25

... are defined without reference to religion, (iii) has the effect of furthering a development objective... available to a wide range of organizations and beneficiaries which are defined without reference to religion...

Corresponding color datasets and a chromatic adaptation model based on the OSA-UCS system.

PubMed

Oleari, Claudio

2014-07-01

Today chromatic adaptation transforms (CATs) are reconsidered, since their mathematical inconsistency has been shown in Color Res. Appl.38, 188 (2013) and by the CIE technical committee TC 8-11: CIECAM02 Mathematics. In 2004-2005 the author proposed an adaptation transform based on the uniform color scale system of the Optical Society of America (OSA-UCS) [J. Opt. Soc. Am. A21, 677 (2004); Color Res. Appl. 30, 31 (2005)] that transforms the cone-activation stimuli into adapted stimuli. The present work considers all the 37 available corresponding color (CC) datasets selected by CIE and (1) shows that the adapted stimuli obtained from CC data are defined up to an unknown transformation, and an unambiguous definition of the adapted stimuli requires additional hypotheses or suitable experimental data (as it is in the OSA-UCS system); (2) produces a CAT, represented by a linear transformation between CCs, associated with any CC dataset, whose high quality measured in ΔE units discards the possibility of nonlinear transformations; (3) analyzes these color-conversion matrices in a heuristic way with a reference adaptation that is approximately that of the OSA-UCS adapted colors for the D65 illuminant and particularly shows accordance with the Hunt effect and the Bezold-Brücke hue shift; (4) proposes the measurements of CC stimuli with a reference adaptation equal to that of the visual situation of the OSA-UCS system for defining adapted colors for any considered illumination adaptation and therefore for defining a general CAT formula.

Fifty Years of Physics of Living Systems.

PubMed

Latash, Mark L

2016-01-01

The equilibrium-point hypothesis and its more recent version, the referent configuration hypothesis, represent the physical approach to the neural control of action. This hypothesis can be naturally combined with the idea of hierarchical control of movements and of synergic organization of the abundant systems involved in all actions. Any action starts with defining trajectories of a few referent coordinates for a handful of salient task-specific variables. Further, referent coordinates at hierarchically lower levels emerge down to thresholds of the tonic stretch reflex for the participating muscles. Stability of performance with respect to salient variables is reflected in the structure of inter-trial variance and phenomena of motor equivalence. Three lines of recent research within this framework are reviewed. First, synergic adjustments of the referent coordinate and apparent stiffness have been demonstrated during finger force production supporting the main idea of control with referent coordinates. Second, the notion of unintentional voluntary movements has been introduced reflecting unintentional drifts in referent coordinates. Two types of unintentional movements have been observed with different characteristic times. Third, this framework has been applied to studies of impaired movements in neurological patients. Overall, the physical approach searching for laws of nature underlying biological movement has been highly stimulating and productive.

Innovation and reliability of atomic standards for PTTI applications

NASA Technical Reports Server (NTRS)

Kern, R.

1981-01-01

Innovation and reliability in hyperfine frequency standards and clock systems are discussed. Hyperfine standards are defined as those precision frequency sources and clocks which use a hyperfine atomic transition for frequency control and which have realized significant commercial production and acceptance (cesium, hydrogen, and rubidium atoms). References to other systems such as thallium and ammonia are excluded since these atomic standards have not been commercially exploited in this country.

Delirium diagnosis defined by cluster analysis of symptoms versus diagnosis by DSM and ICD criteria: diagnostic accuracy study.

PubMed

Sepulveda, Esteban; Franco, José G; Trzepacz, Paula T; Gaviria, Ana M; Meagher, David J; Palma, José; Viñuelas, Eva; Grau, Imma; Vilella, Elisabet; de Pablo, Joan

2016-05-26

Information on validity and reliability of delirium criteria is necessary for clinicians, researchers, and further developments of DSM or ICD. We compare four DSM and ICD delirium diagnostic criteria versions, which were developed by consensus of experts, with a phenomenology-based natural diagnosis delineated using cluster analysis of delirium features in a sample with a high prevalence of dementia. We also measured inter-rater reliability of each system when applied by two evaluators from distinct disciplines. Cross-sectional analysis of 200 consecutive patients admitted to a skilled nursing facility, independently assessed within 24-48 h after admission with the Delirium Rating Scale-Revised-98 (DRS-R98) and for DSM-III-R, DSM-IV, DSM-5, and ICD-10 criteria for delirium. Cluster analysis (CA) delineated natural delirium and nondelirium reference groups using DRS-R98 items and then diagnostic systems' performance were evaluated against the CA-defined groups using logistic regression and crosstabs for discriminant analysis (sensitivity, specificity, percentage of subjects correctly classified by each diagnostic system and their individual criteria, and performance for each system when excluding each individual criterion are reported). Kappa Index (K) was used to report inter-rater reliability for delirium diagnostic systems and their individual criteria. 117 (58.5 %) patients had preexisting dementia according to the Informant Questionnaire on Cognitive Decline in the Elderly. CA delineated 49 delirium subjects and 151 nondelirium. Against these CA groups, delirium diagnosis accuracy was highest using DSM-III-R (87.5 %) followed closely by DSM-IV (86.0 %), ICD-10 (85.5 %) and DSM-5 (84.5 %). ICD-10 had the highest specificity (96.0 %) but lowest sensitivity (53.1 %). DSM-III-R had the best sensitivity (81.6 %) and the best sensitivity-specificity balance. DSM-5 had the highest inter-rater reliability (K =0.73) while DSM-III-R criteria were the least reliable. Using our CA-defined, phenomenologically-based delirium designations as the reference standard, we found performance discordance among four diagnostic systems when tested in subjects where comorbid dementia was prevalent. The most complex diagnostic systems have higher accuracy and the newer DSM-5 have higher reliability. Our novel phenomenological approach to designing a delirium reference standard may be preferred to guide revisions of diagnostic systems in the future.

Formulary Selection Criteria for Biosimilars: Considerations for US Health-System Pharmacists.

PubMed

Griffith, Niesha; McBride, Ali; Stevenson, James G; Green, Larry

2014-10-01

Pharmacists will play a key role in evaluating biosimilars for formulary inclusion in the United States. As defined by US law, a biosimilar is a biologic that is highly similar to its reference product, notwithstanding minor differences in clinically inactive components, and should not have clinically meaningful differences from its reference product in safety, purity, and potency. We review biosimilars and the current European Union and US regulatory pathways for biosimilars. Furthermore, we propose a checklist of considerations to ensure that US pharmacists thoroughly evaluate future biosimilars for formulary inclusion. Included in the checklist are considerations related to the availability of preapproval and postapproval safety and efficacy data; differences in product characteristics and immunogenicity between the biosimilar and reference product; manufacturer-related parameters that can affect a reliable supply of quality products; health-system and patient perspectives on product packaging, labeling, storage, and administration; costs and insurance coverage; patient education; interchangeability and differences in the range of indications; and evaluation of institutions' information technology systems.

Formulary Selection Criteria for Biosimilars: Considerations for US Health-System Pharmacists

PubMed Central

McBride, Ali; Stevenson, James G.; Green, Larry

2014-01-01

Abstract Pharmacists will play a key role in evaluating biosimilars for formulary inclusion in the United States. As defined by US law, a biosimilar is a biologic that is highly similar to its reference product, notwithstanding minor differences in clinically inactive components, and should not have clinically meaningful differences from its reference product in safety, purity, and potency. We review biosimilars and the current European Union and US regulatory pathways for biosimilars. Furthermore, we propose a checklist of considerations to ensure that US pharmacists thoroughly evaluate future biosimilars for formulary inclusion. Included in the checklist are considerations related to the availability of preapproval and postapproval safety and efficacy data; differences in product characteristics and immunogenicity between the biosimilar and reference product; manufacturer-related parameters that can affect a reliable supply of quality products; health-system and patient perspectives on product packaging, labeling, storage, and administration; costs and insurance coverage; patient education; interchangeability and differences in the range of indications; and evaluation of institutions’ information technology systems. PMID:25477613

Uncovering the Hidden Structure of Platoons: Formal and Emergent Leaders’ Perceptions of Organizational Networks

DTIC Science & Technology

2008-12-01

perceptions of formal and emergent leaders differ from those of non-leaders, and if so, how. We approach this topic through the lens of social network...analysis. 1.1 Social Networks The term “ social network” refers to a set of actors who are connected by a set of ties. Actors, often referred to as...the structure of any social system can be defined as a set of relations between all pairs of individuals who are members of the network (Krackhardt

Astrometry for New Reductions: The ANR method

NASA Astrophysics Data System (ADS)

Robert, Vincent; Le Poncin-Lafitte, Christophe

2018-04-01

Accurate positional measurements of planets and satellites are used to improve our knowledge of their orbits and dynamics, and to infer the accuracy of the planet and satellite ephemerides. With the arrival of the Gaia-DR1 reference star catalog and its complete release afterward, the methods for ground-based astrometry become outdated in terms of their formal accuracy compared to the catalog's which is used. Systematic and zonal errors of the reference stars are eliminated, and the astrometric process now dominates in the error budget. We present a set of algorithms for computing the apparent directions of planets, satellites and stars on any date to micro-arcsecond precision. The expressions are consistent with the ICRS reference system, and define the transformation between theoretical reference data, and ground-based astrometric observables.

An algorithm for control system design via parameter optimization. M.S. Thesis

NASA Technical Reports Server (NTRS)

Sinha, P. K.

1972-01-01

An algorithm for design via parameter optimization has been developed for linear-time-invariant control systems based on the model reference adaptive control concept. A cost functional is defined to evaluate the system response relative to nominal, which involves in general the error between the system and nominal response, its derivatives and the control signals. A program for the practical implementation of this algorithm has been developed, with the computational scheme for the evaluation of the performance index based on Lyapunov's theorem for stability of linear invariant systems.

Manned space flight nuclear system safety. Volume 3: Reactor system preliminary nuclear safety analysis. Part 1: Reference Design Document (RDD)

NASA Technical Reports Server (NTRS)

1972-01-01

The Reference Design Document, of the Preliminary Safety Analysis Report (PSAR) - Reactor System provides the basic design and operations data used in the nuclear safety analysis of the Rector Power Module as applied to a Space Base program. A description of the power module systems, facilities, launch vehicle and mission operations, as defined in NASA Phase A Space Base studies is included. Each of two Zirconium Hydride Reactor Brayton power modules provides 50 kWe for the nominal 50 man Space Base. The INT-21 is the prime launch vehicle. Resupply to the 500 km orbit over the ten year mission is provided by the Space Shuttle. At the end of the power module lifetime (nominally five years), a reactor disposal system is deployed for boost into a 990 km high altitude (long decay time) earth orbit.

A reference architecture for integrated EHR in Colombia.

PubMed

de la Cruz, Edgar; Lopez, Diego M; Uribe, Gustavo; Gonzalez, Carolina; Blobel, Bernd

2011-01-01

The implementation of national EHR infrastructures has to start by a detailed definition of the overall structure and behavior of the EHR system (system architecture). Architectures have to be open, scalable, flexible, user accepted and user friendly, trustworthy, based on standards including terminologies and ontologies. The GCM provides an architectural framework created with the purpose of analyzing any kind of system, including EHR system´s architectures. The objective of this paper is to propose a reference architecture for the implementation of an integrated EHR in Colombia, based on the current state of system´s architectural models, and EHR standards. The proposed EHR architecture defines a set of services (elements) and their interfaces, to support the exchange of clinical documents, offering an open, scalable, flexible and semantically interoperable infrastructure. The architecture was tested in a pilot tele-consultation project in Colombia, where dental EHR are exchanged.

Quantum mechanics in noninertial reference frames: Relativistic accelerations and fictitious forces

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klink, W.H., E-mail: william-klink@uiowa.edu; Wickramasekara, S., E-mail: wickrama@grinnell.edu

2016-06-15

One-particle systems in relativistically accelerating reference frames can be associated with a class of unitary representations of the group of arbitrary coordinate transformations, an extension of the Wigner–Bargmann definition of particles as the physical realization of unitary irreducible representations of the Poincaré group. Representations of the group of arbitrary coordinate transformations become necessary to define unitary operators implementing relativistic acceleration transformations in quantum theory because, unlike in the Galilean case, the relativistic acceleration transformations do not themselves form a group. The momentum operators that follow from these representations show how the fictitious forces in noninertial reference frames are generated inmore » quantum theory.« less

International Organisations and the Evaluation of Education Systems: A Critical Comparative Analysis

ERIC Educational Resources Information Center

Neves, Claudia

2008-01-01

This article seeks to develop research involving a macro-level critical comparative analysis of reference documents produced by international organisations (UNDP, OECD, UNESCO, the World Bank and the European Union) which guide world education policy decisions. The primary objective was to consider the key guidelines currently defined for…

Education Quality in Kazakhstan in the Context of Competence-Based Approach

ERIC Educational Resources Information Center

Nabi, Yskak; Zhaxylykova, Nuriya Ermuhametovna; Kenbaeva, Gulmira Kaparbaevna; Tolbayev, Abdikerim; Bekbaeva, Zeinep Nusipovna

2016-01-01

The background of this paper is to present how education system of Kazakhstan evolved during the last 24 years of independence, highlighting the contemporary transformational processes. We defined the aim to identify the education quality in the context of competence-based approach. Methods: Analysis of references, interviewing, experimental work.…

Derivation and definition of a linear aircraft model

NASA Technical Reports Server (NTRS)

Duke, Eugene L.; Antoniewicz, Robert F.; Krambeer, Keith D.

1988-01-01

A linear aircraft model for a rigid aircraft of constant mass flying over a flat, nonrotating earth is derived and defined. The derivation makes no assumptions of reference trajectory or vehicle symmetry. The linear system equations are derived and evaluated along a general trajectory and include both aircraft dynamics and observation variables.

Space station needs, attributes and architectural options: Architectural options and selection

NASA Technical Reports Server (NTRS)

Nelson, W. G.

1983-01-01

The approach, study results, and recommendations for defining and selecting space station architectural options are described. Space station system architecture is defined as the arrangement of elements (manned and unmanned on-orbit facilities, shuttle vehicles, orbital transfer vehicles, etc.), the number of these elements, their location (orbital inclination and altitude, and their functional performance capability, power, volume, crew, etc.). Architectural options are evaluated based on the degree of mission capture versus cost and required funding rate. Mission capture refers to the number of missions accommodated by the particular architecture.

[Risk management of soybean-related asthma: monitoring and surveillance].

PubMed

Villalbí, Joan R; Carrascal, Dolors; Caylà, Joan A; Rodríguez, Pau; Cruz, M A Jesús; Pintó, Josep M

2011-01-01

Allergen emissions during soybean unloading operations in the Barcelona harbor have caused asthma epidemics. The present article aimed to describe the surveillance and control measures carried out by the public health services. Data were extracted from control systems from 1999 to 2009, with description of the surveillance schemes for allergen emissions, environmental concentrations (with defined reference levels) and for health. Of 95 studies of plant emission, four were above the reference levels, and filters were found to be the most likely cause. Mean environmental concentrations were low but were above the reference levels on 13 days; these levels were related to adverse meteorological conditions and incidents in the plants. No health effects were detected in the panel of patients nor epidemic asthma days. The system detects incidents and has shown its usefulness in protecting public health. Copyright © 2011 SESPAS. Published by Elsevier Espana. All rights reserved.

IBM system/360 assembly language interval arithmetic software

NASA Technical Reports Server (NTRS)

Phillips, E. J.

1972-01-01

Computer software designed to perform interval arithmetic is described. An interval is defined as the set of all real numbers between two given numbers including or excluding one or both endpoints. Interval arithmetic consists of the various elementary arithmetic operations defined on the set of all intervals, such as interval addition, subtraction, union, etc. One of the main applications of interval arithmetic is in the area of error analysis of computer calculations. For example, it has been used sucessfully to compute bounds on sounding errors in the solution of linear algebraic systems, error bounds in numerical solutions of ordinary differential equations, as well as integral equations and boundary value problems. The described software enables users to implement algorithms of the type described in references efficiently on the IBM 360 system.

Modernizing the National Spatial Reference System

NASA Astrophysics Data System (ADS)

Smith, D. A.

2016-12-01

The National Spatial Reference System (NSRS) is that system of datums, reference frames, shorelines, software and standards which serve the entire federal civilian geospatial community. It is the mission of the National Geodetic Survey (NGS) to define, maintain and provide access to the NSRS. Currently the NSRS contains three geometric reference frames (NAD 83(2011), NAD 83(PA11) and NAD 83(MA11)), one dynamic height datum (IGLD 85) and 6 vertical datums (NAVD 88, PRVD02, ASVD02, NMVD03, GUVD04, VIVD09). All of these datums are built on aging technology and contain systematic errors that grow more noticeable as access to accurate positioning becomes more widespread. It was determined by NGS in 2007 that this was not sustainable and as such, all datums and reference frames are scheduled to be replaced in 2022. [At the time of this abstract, the exact names of the replacements are being finalized and are expected to be announced by the AGU fall meeting.] Replacing the official datums and reference frames requires a carefully coordinated effort of dozens of interrelated technical projects spanning years (over a decade in some cases) and involving a majority of NGS employees. This talk will cover the plans thus far, projects completed, projects underway and will summarize the NSRS as it is expected to look and be accessed in 2022 and beyond.

Defining a reference range for vital signs in healthy term pregnant women undergoing caesarean section.

PubMed

Dennis, A; Hardy, L

2016-11-01

Early warning systems (EWS), used to identify deteriorating hospitalised patients, are based on measurement of vital signs. When the patients are pregnant, most EWS still use non-pregnant reference ranges of vital signs to determine trigger thresholds. There are no published reference ranges for all vital signs in pregnancy. We aimed to define vital signs reference ranges for term pregnancy in the preoperative period, and to determine the appropriateness of EWS trigger criteria in pregnancy. We conducted a one-year retrospective study in a tertiary referral obstetric hospital. The study sample was healthy term women undergoing planned caesarean section (CS). Systolic blood pressure (SBP), diastolic blood pressure (DBP), heart rate (HR), oxygen saturation (SpO 2 ) and temperature were all measured automatically and data was extracted from the medical record. Two hundred and fifty-eight women met inclusion criteria. Results were (mean ± SD [standard deviation]) SBP 118 ± 11.2 mmHg, DBP 75 ± 10.3 mmHg, HR 84 ± 10.2 /minute, respiratory rate 18 ± 1.5 /minute, SpO 2 99%  ± 1.0% and temperature 36.4°C ± 0.43°C. The reference ranges (mean ± 2SD) determined were SBP 96-140 mmHg, DBP 54-96 mmHg, HR 64-104/minute, RR 15-21 /minute, SpO 2 97%-100% and temperature 35.5°C-37.3°C. This study defined a reference range for vital signs in healthy term pregnant women undergoing CS. Study findings suggest that currently used criteria for EWS triggers, based on non-pregnant values, may be too extreme for timely detection of deteriorating pregnant patients. Further research examining the modified HR triggers of ≤50 and ≥110 /minute in pregnant women and their relationship to clinical outcomes is required.

Transmit-reference methods in software defined radio platforms for communication in harsh propagation environments and systems thereof

DOEpatents

Dowla, Farid U; Nekoogar, Faranak

2015-03-03

A method for adaptive Radio Frequency (RF) jamming according to one embodiment includes dynamically monitoring a RF spectrum; detecting any undesired signals in real time from the RF spectrum; and sending a directional countermeasure signal to jam the undesired signals. A method for adaptive Radio Frequency (RF) communications according to another embodiment includes transmitting a data pulse in a RF spectrum; and transmitting a reference pulse separated by a predetermined period of time from the data pulse; wherein the data pulse is modulated with data, wherein the reference pulse is unmodulated. A method for adaptive Radio Frequency (RF) communications according to yet another embodiment includes receiving a data pulse in a RF spectrum; and receiving a reference pulse separated in time from the data pulse, wherein the data pulse is modulated with data, wherein the reference pulse is unmodulated; and demodulating the pulses.

Transmit-reference methods in software defined radio platforms for communication in harsh propagation environments and systems thereof

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dowla, Farid; Nekoogar, Faranak

A method for adaptive Radio Frequency (RF) jamming according to one embodiment includes dynamically monitoring a RF spectrum; detecting any undesired signals in real time from the RF spectrum; and sending a directional countermeasure signal to jam the undesired signals. A method for adaptive Radio Frequency (RF) communications according to another embodiment includes transmitting a data pulse in a RF spectrum; and transmitting a reference pulse separated by a predetermined period of time from the data pulse; wherein the data pulse is modulated with data, wherein the reference pulse is unmodulated. A method for adaptive Radio Frequency (RF) communications accordingmore » to yet another embodiment includes receiving a data pulse in a RF spectrum; and receiving a reference pulse separated in time from the data pulse, wherein the data pulse is modulated with data, wherein the reference pulse is unmodulated; and demodulating the pulses.« less

Availability analysis of an HTGR fuel recycle facility. Summary report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sharmahd, J.N.

1979-11-01

An availability analysis of reprocessing systems in a high-temperature gas-cooled reactor (HTGR) fuel recycle facility was completed. This report summarizes work done to date to define and determine reprocessing system availability for a previously planned HTGR recycle reference facility (HRRF). Schedules and procedures for further work during reprocessing development and for HRRF design and construction are proposed in this report. Probable failure rates, transfer times, and repair times are estimated for major system components. Unscheduled down times are summarized.

Environmental diseases of the digestive system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rubin, E.; Farber, J.L.

1990-03-01

Environmental factors are important mediators of many diseases of the digestive system, defined as the alimentary tract and the accessory organs of digestion, the liver and pancreas. In this review, we principally focus on the action of chemical agents which are classified as (1) naturally occurring compounds, (2) occupational hazards, (3) therapeutic drugs, and (4) constituents of substances of abuse. In addition, the putative role of dietary habits in the pathogenesis of malignant diseases of the digestive system is discussed.54 references.

Upcoming replacements for NAD83, NAVD88 and IGLD85

NASA Astrophysics Data System (ADS)

Smith, D. A.; Snay, R.

2009-05-01

The National Geodetic Survey (NGS), part of the National Oceanic and Atmospheric Administration (NOAA) is responsible for defining, maintaining and providing access to the National Spatial Reference System (NSRS) for the United States. The NSRS is the official system to which all civil federal mapping agencies should refer, and contains, amongst other things, the official geopotential (historically "vertical") datum of NAVD 88, the 3-D geometric reference system (historically "horizontal datum") of NAD 83 and great lakes datum (IGLD 85). Although part of the United States NSRS, all three of these datums have been created through international partnerships across North America. Unfortunately, time has shown both the systematic errors existent within these datums, as well as the inherent weaknesses of relying exclusively on passive monuments to define and provide access to these datums. In recognition of these issues, the National Geodetic Survey has issued a "10 year plan", available online, which outlines steps which will be taken to update NAD 83, NAVD 88 and IGLD 85 concurrently around the year 2018. The primary source of success will be in the refinement of the CORS network and the upcoming execution of the GRAV-D project (Gravity for the Re-definition of the American Vertical Datum). Conversations are ongoing with colleagues in Canada, Mexico, Central America and the Caribbean in order to coordinate all of these efforts across the entire continent. The largest changes expected to occur are the removal of over 2 meters of non-geocentricity in NAD 83; the removal of decimeters of bias and over a meter of tilt in NAVD 88; the addition of the ability to track crustal motions (subsidence, tectonics, etc) in the datums; the removal of leveling as a tool for long-line height differencing; the use of a "best" geoid as the orthometric height reference surface; the addition of datum velocities (motions of the 3-D geometric reference system origin and motions of the geoid); and the use of GNSS technology as the way to access both orthometric and dynamic heights in the vertical datum. This talk will outline the broad plan of action and invite further collaboration along these lines.

The Wavelet Element Method. Part 2; Realization and Additional Features in 2D and 3D

NASA Technical Reports Server (NTRS)

Canuto, Claudio; Tabacco, Anita; Urban, Karsten

1998-01-01

The Wavelet Element Method (WEM) provides a construction of multiresolution systems and biorthogonal wavelets on fairly general domains. These are split into subdomains that are mapped to a single reference hypercube. Tensor products of scaling functions and wavelets defined on the unit interval are used on the reference domain. By introducing appropriate matching conditions across the interelement boundaries, a globally continuous biorthogonal wavelet basis on the general domain is obtained. This construction does not uniquely define the basis functions but rather leaves some freedom for fulfilling additional features. In this paper we detail the general construction principle of the WEM to the 1D, 2D and 3D cases. We address additional features such as symmetry, vanishing moments and minimal support of the wavelet functions in each particular dimension. The construction is illustrated by using biorthogonal spline wavelets on the interval.

The use and abuse of standard stars

NASA Astrophysics Data System (ADS)

Garrison, R. F.

The 'mandate' of classification systems is examined with reference to spectral classification. In using a classification system, it is of the greatest importance to be aware of why it was created, how it was constructed, what its useful limits are, how it has evolved, and what credibility it has achieved in practice . . . all of which constitute the mandate of the system. In the particular case of the MK system of spectral classification, types are defined by the standard stars. They can be calibrated, and the calibration may evolve with time, but the types are relatively stable because they are defined by the standards. The autonomy of this powerful system is crucial to its success, but some astronomers do not understand the importance of this distinction. Recent suggestions to change the spectral type of the sun show an ignorance of the way the system works. The confrontation and complementary use of autonomous systems yield information which is not contained in any individual system.

The implementation of aerial object recognition algorithm based on contour descriptor in FPGA-based on-board vision system

NASA Astrophysics Data System (ADS)

Babayan, Pavel; Smirnov, Sergey; Strotov, Valery

2017-10-01

This paper describes the aerial object recognition algorithm for on-board and stationary vision system. Suggested algorithm is intended to recognize the objects of a specific kind using the set of the reference objects defined by 3D models. The proposed algorithm based on the outer contour descriptor building. The algorithm consists of two stages: learning and recognition. Learning stage is devoted to the exploring of reference objects. Using 3D models we can build the database containing training images by rendering the 3D model from viewpoints evenly distributed on a sphere. Sphere points distribution is made by the geosphere principle. Gathered training image set is used for calculating descriptors, which will be used in the recognition stage of the algorithm. The recognition stage is focusing on estimating the similarity of the captured object and the reference objects by matching an observed image descriptor and the reference object descriptors. The experimental research was performed using a set of the models of the aircraft of the different types (airplanes, helicopters, UAVs). The proposed orientation estimation algorithm showed good accuracy in all case studies. The real-time performance of the algorithm in FPGA-based vision system was demonstrated.

Space-Based Reconfigurable Software Defined Radio Test Bed Aboard International Space Station

NASA Technical Reports Server (NTRS)

Reinhart, Richard C.; Lux, James P.

2014-01-01

The National Aeronautical and Space Administration (NASA) recently launched a new software defined radio research test bed to the International Space Station. The test bed, sponsored by the Space Communications and Navigation (SCaN) Office within NASA is referred to as the SCaN Testbed. The SCaN Testbed is a highly capable communications system, composed of three software defined radios, integrated into a flight system, and mounted to the truss of the International Space Station. Software defined radios offer the future promise of in-flight reconfigurability, autonomy, and eventually cognitive operation. The adoption of software defined radios offers space missions a new way to develop and operate space transceivers for communications and navigation. Reconfigurable or software defined radios with communications and navigation functions implemented in software or VHDL (Very High Speed Hardware Description Language) provide the capability to change the functionality of the radio during development or after launch. The ability to change the operating characteristics of a radio through software once deployed to space offers the flexibility to adapt to new science opportunities, recover from anomalies within the science payload or communication system, and potentially reduce development cost and risk by adapting generic space platforms to meet specific mission requirements. The software defined radios on the SCaN Testbed are each compliant to NASA's Space Telecommunications Radio System (STRS) Architecture. The STRS Architecture is an open, non-proprietary architecture that defines interfaces for the connections between radio components. It provides an operating environment to abstract the communication waveform application from the underlying platform specific hardware such as digital-to-analog converters, analog-to-digital converters, oscillators, RF attenuators, automatic gain control circuits, FPGAs, general-purpose processors, etc. and the interconnections among different radio components.

Development Requirements for Spacesuit Elbow Joint

NASA Technical Reports Server (NTRS)

Peters, Benjamin

2017-01-01

Functional Requirements for spacesuit elbow joint:1) The system is a conformal, single-axis spacesuit pressurized joint that encloses the elbow joint of the suited user and uses a defined interface to connect to the suit systems on either side of the joint.2) The system shall be designed to bear the loads incurred from the internal pressure of the system, as well as the expected loads induced by the user while enabling the user move the joint through the required range of motion. The joint torque of the system experienced by the user shall remain at or below the required specification for the entire range of motion.3) The design shall be constructed, at a minimum, as a two-layer system. The internal, air-tight layer shall be referred to as the bladder, and the layer on the unpressurized side of the bladder shall be referred to as the restraint. The design of the system may include additional features or layers, such as axial webbing, to meet the overall requirements of the design.

Advanced Life Support Research and Technology Development Metric

NASA Technical Reports Server (NTRS)

Hanford, A. J.

2004-01-01

The Metric is one of several measures employed by the NASA to assess the Agency s progress as mandated by the United States Congress and the Office of Management and Budget. Because any measure must have a reference point, whether explicitly defined or implied, the Metric is a comparison between a selected ALS Project life support system and an equivalently detailed life support system using technology from the Environmental Control and Life Support System (ECLSS) for the International Space Station (ISS). This document provides the official calculation of the Advanced Life Support (ALS) Research and Technology Development Metric (the Metric) for Fiscal Year 2004. The values are primarily based on Systems Integration, Modeling, and Analysis (SIMA) Element approved software tools or reviewed and approved reference documents. For Fiscal Year 2004, the Advanced Life Support Research and Technology Development Metric value is 2.03 for an Orbiting Research Facility and 1.62 for an Independent Exploration Mission.

SMART-1/CLEMENTINE Study of Humorum and Procellarum Basins

NASA Astrophysics Data System (ADS)

Carey, William; Foing, Bernard H.; Koschny, Detlef; Pio Rossi, Angelo; Josset, Jean-Luc

A study undertaken by ESA to define a European Reference Architecture for Space Exploration is due to be completed in September 2008. The development of this architecture over the past twelve months has identified a number of key capabilities, among them a lunar lander system, which could form the basis for Europe's contribution to the future exploration of space in collaboration with International Partners. The focus of this paper will be on the lunar lander system, and will present the results of an analysis of possible payloads that could be accommodated by the lander. As the industrial study is at the Phase 0 or Pre-Phase A level, the design of such a lander system is at a very early stage in its development, but an estimation of the payload capacity allows a general assessment of the types of possible payloads that could be carried, currently this capacity is estimated at 1.1 tonnes of gross payload mass to the lunar surface (assuming an Ariane 5 ECA launch). An important characteristic of the lunar lander is that it provides a versatile and flexible system for utilisation in a broad range of lunar missions which include: - Independent lunar exploration missions for science, technology demonstration and research. - Delivery of logistics and cargo to support human surface sortie missions. - Delivery of logistics to a lunar base/outpost. - Deployment of individual infrastructure elements in support of a lunar base/outpost. Based on the above different types of missions, a number of configurations of "reference payload" sets are in the process of being defined that cover specific exploration objectives related primarily to capability demonstration, exploration enabling research and enabled science. Aspects covered include: ISRU, robotics, mobility, human preparation, life science and geology. This paper will present the current status of definition of the Reference Payload sets.

Privacy enhanced group communication in clinical environment

NASA Astrophysics Data System (ADS)

Li, Mingyan; Narayanan, Sreeram; Poovendran, Radha

2005-04-01

Privacy protection of medical records has always been an important issue and is mandated by the recent Health Insurance Portability and Accountability Act (HIPAA) standards. In this paper, we propose security architectures for a tele-referring system that allows electronic group communication among professionals for better quality treatments, while protecting patient privacy against unauthorized access. Although DICOM defines the much-needed guidelines for confidentiality of medical data during transmission, there is no provision in the existing medical security systems to guarantee patient privacy once the data has been received. In our design, we address this issue by enabling tracing back to the recipient whose received data is disclosed to outsiders, using watermarking technique. We present security architecture design of a tele-referring system using a distributed approach and a centralized web-based approach. The resulting tele-referring system (i) provides confidentiality during the transmission and ensures integrity and authenticity of the received data, (ii) allows tracing of the recipient who has either distributed the data to outsiders or whose system has been compromised, (iii) provides proof of receipt or origin, and (iv) can be easy to use and low-cost to employ in clinical environment.

Editorial: Challenges and solutions in GW calculations for complex systems

NASA Astrophysics Data System (ADS)

Giustino, F.; Umari, P.; Rubio, A.

2012-09-01

We report key advances in the area of GW calculations, review the available software implementations and define standardization criteria to render the comparison between GW calculations from different codes meaningful, and identify future major challenges in the area of quasiparticle calculations. This Topical Issue should be a reference point for further developments in the field.

36 CFR 219.1 - Purpose and applicability.

Code of Federal Regulations, 2014 CFR

2014-07-01

... (also referred to as plans) for units of the National Forest System (NFS), as required by the Forest and... other content in land management plans. This part is applicable to all units of the NFS as defined by 16... (16 U.S.C. 528-531) (MUSYA), the Forest Service manages the NFS to sustain the multiple use of its...

36 CFR 219.1 - Purpose and applicability.

Code of Federal Regulations, 2012 CFR

2012-07-01

... (also referred to as plans) for units of the National Forest System (NFS), as required by the Forest and... other content in land management plans. This part is applicable to all units of the NFS as defined by 16... (16 U.S.C. 528-531) (MUSYA), the Forest Service manages the NFS to sustain the multiple use of its...

36 CFR 219.1 - Purpose and applicability.

Code of Federal Regulations, 2013 CFR

2013-07-01

... (also referred to as plans) for units of the National Forest System (NFS), as required by the Forest and... other content in land management plans. This part is applicable to all units of the NFS as defined by 16... (16 U.S.C. 528-531) (MUSYA), the Forest Service manages the NFS to sustain the multiple use of its...

System engineering toolbox for design-oriented engineers

NASA Technical Reports Server (NTRS)

Goldberg, B. E.; Everhart, K.; Stevens, R.; Babbitt, N., III; Clemens, P.; Stout, L.

1994-01-01

This system engineering toolbox is designed to provide tools and methodologies to the design-oriented systems engineer. A tool is defined as a set of procedures to accomplish a specific function. A methodology is defined as a collection of tools, rules, and postulates to accomplish a purpose. For each concept addressed in the toolbox, the following information is provided: (1) description, (2) application, (3) procedures, (4) examples, if practical, (5) advantages, (6) limitations, and (7) bibliography and/or references. The scope of the document includes concept development tools, system safety and reliability tools, design-related analytical tools, graphical data interpretation tools, a brief description of common statistical tools and methodologies, so-called total quality management tools, and trend analysis tools. Both relationship to project phase and primary functional usage of the tools are also delineated. The toolbox also includes a case study for illustrative purposes. Fifty-five tools are delineated in the text.

Fast state transfer in a Λ-system: a shortcut-to-adiabaticity approach to robust and resource optimized control

NASA Astrophysics Data System (ADS)

Mortensen, Henrik Lund; Sørensen, Jens Jakob W. H.; Mølmer, Klaus; Sherson, Jacob Friis

2018-02-01

We propose an efficient strategy to find optimal control functions for state-to-state quantum control problems. Our procedure first chooses an input state trajectory, that can realize the desired transformation by adiabatic variation of the system Hamiltonian. The shortcut-to-adiabaticity formalism then provides a control Hamiltonian that realizes the reference trajectory exactly but on a finite time scale. As the final state is achieved with certainty, we define a cost functional that incorporates the resource requirements and a perturbative expression for robustness. We optimize this functional by systematically varying the reference trajectory. We demonstrate the method by application to population transfer in a laser driven three-level Λ-system, where we find solutions that are fast and robust against perturbations while maintaining a low peak laser power.

Energy efficient engine: Flight propulsion system preliminary analysis and design

NASA Technical Reports Server (NTRS)

Johnston, R. P.; Beitler, R. S.; Bobinger, R. O.; Broman, C. L.; Gravitt, R. D.; Heineke, H.; Holloway, P. R.; Klem, J. S.; Nash, D. O.; Ortiz, P.

1980-01-01

The characteristics of an advanced flight propulsion system (FPS), suitable for introduction in the late 1980's to early 1990's, was more fully defined. It was determined that all goals for efficiency, environmental considerations, and economics could be met or exceeded with the possible exception of NOx emission. In evaluating the FPS, all aspects were considered including component design, performance, weight, initial cost, maintenance cost, engine system integration (including nacelle), and aircraft integration considerations. The current FPS installed specific fuel consumption was reduced 14.2% from that of the CF6-50C reference engine. When integrated into an advanced, subsonic, study transport, the FPS produced a fuel burn savings of 15 to 23% and a direct operating cost reduction of 5 to 12% depending on the mission and study aircraft characteristics relative to the reference engine.

Central role of the observable electric potential in transport equations.

PubMed

Garrido, J; Compañ, V; López, M L

2001-07-01

Nonequilibrium systems are usually studied in the framework of transport equations that involve the true electric potential (TEP), a nonobservable variable. Nevertheless another electric potential, the observable electric potential (OEP), may be defined to construct a useful set of transport equations. In this paper several basic characteristics of the OEP are deduced and emphasized: (i) the OEP distribution depends on thermodynamic state of the solution, (ii) the observable equations have a reference value for all other transport equations, (iii) the bridge that connects the OEP with a certain TEP is usually defined by the ion activity coefficient, (iv) the electric charge density is a nonobservable variable, and (v) the OEP formulation constitutes a natural model for studying the fluxes in membrane systems.

Manned geosynchronous mission requirements and systems analysis study extension. Volume 1: Executive summary

NASA Technical Reports Server (NTRS)

1981-01-01

A study was performed to determine the types of manned missions that will likely be performed in the late 1980's or early 1990's timeframe, to define MOTV configurations which satisfy these missions requirements, and to develop a program plan for its development. Twenty generic missions were originally defined for MOTV but, to simplify the selection process, five of these missions were selected as typical and used as Design Reference Missions. Systems and subsystems requirements were re-examined and sensitivity analyses performed to determine optimum point designs. Turnaround modes were considered to determine the most effective combination of ground based and spaced based activities. A preferred concept for the crew capsule and for the mission mode was developed.

Structure and thermodynamics of a mixture of patchy and spherical colloids: A multi-body association theory with complete reference fluid information

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bansal, Artee; Asthagiri, D.; Cox, Kenneth R.

A mixture of solvent particles with short-range, directional interactions and solute particles with short-range, isotropic interactions that can bond multiple times is of fundamental interest in understanding liquids and colloidal mixtures. Because of multi-body correlations, predicting the structure and thermodynamics of such systems remains a challenge. Earlier Marshall and Chapman [J. Chem. Phys. 139, 104904 (2013)] developed a theory wherein association effects due to interactions multiply the partition function for clustering of particles in a reference hard-sphere system. The multi-body effects are incorporated in the clustering process, which in their work was obtained in the absence of the bulk medium.more » The bulk solvent effects were then modeled approximately within a second order perturbation approach. However, their approach is inadequate at high densities and for large association strengths. Based on the idea that the clustering of solvent in a defined coordination volume around the solute is related to occupancy statistics in that defined coordination volume, we develop an approach to incorporate the complete information about hard-sphere clustering in a bulk solvent at the density of interest. The occupancy probabilities are obtained from enhanced sampling simulations but we also develop a concise parametric form to model these probabilities using the quasichemical theory of solutions. We show that incorporating the complete reference information results in an approach that can predict the bonding state and thermodynamics of the colloidal solute for a wide range of system conditions.« less

Approaches to defining reference regimes for river restoration planning

NASA Astrophysics Data System (ADS)

Beechie, T. J.

2014-12-01

Reference conditions or reference regimes can be defined using three general approaches, historical analysis, contemporary reference sites, and theoretical or empirical models. For large features (e.g., floodplain channels and ponds) historical data and maps are generally reliable. For smaller features (e.g., pools and riffles in small tributaries), field data from contemporary reference sites are a reasonable surrogate for historical data. Models are generally used for features that have no historical information or present day reference sites (e.g., beaver pond habitat). Each of these approaches contributes to a watershed-wide understanding of current biophysical conditions relative to potential conditions, which helps create not only a guiding vision for restoration, but also helps quantify and locate the largest or most important restoration opportunities. Common uses of geomorphic and biological reference conditions include identifying key areas for habitat protection or restoration, and informing the choice of restoration targets. Examples of use of each of these three approaches to define reference regimes in western USA illustrate how historical information and current research highlight key restoration opportunities, focus restoration effort in areas that can produce the largest ecological benefit, and contribute to estimating restoration potential and assessing likelihood of achieving restoration goals.

Parametric analysis of closed cycle magnetohydrodynamic (MHD) power plants

NASA Technical Reports Server (NTRS)

Owens, W.; Berg, R.; Murthy, R.; Patten, J.

1981-01-01

A parametric analysis of closed cycle MHD power plants was performed which studied the technical feasibility, associated capital cost, and cost of electricity for the direct combustion of coal or coal derived fuel. Three reference plants, differing primarily in the method of coal conversion utilized, were defined. Reference Plant 1 used direct coal fired combustion while Reference Plants 2 and 3 employed on site integrated gasifiers. Reference Plant 2 used a pressurized gasifier while Reference Plant 3 used a ""state of the art' atmospheric gasifier. Thirty plant configurations were considered by using parametric variations from the Reference Plants. Parametric variations include the type of coal (Montana Rosebud or Illinois No. 6), clean up systems (hot or cold gas clean up), on or two stage atmospheric or pressurized direct fired coal combustors, and six different gasifier systems. Plant sizes ranged from 100 to 1000 MWe. Overall plant performance was calculated using two methodologies. In one task, the channel performance was assumed and the MHD topping cycle efficiencies were based on the assumed values. A second task involved rigorous calculations of channel performance (enthalpy extraction, isentropic efficiency and generator output) that verified the original (task one) assumptions. Closed cycle MHD capital costs were estimated for the task one plants; task two cost estimates were made for the channel and magnet only.

Tutorial for the software tools mail system - MSG

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sventek, V.A.

1984-10-01

This manual was written with two purposes in mind: (1) to get started using the system quickly; and (2) to explain the more advanced features of the system needed when the mail load gets heavier and the time to spend dealing with it gets shorter. The first section shows you how to use the simplest form of each command, giving just enough information to use the mail system comfortably and still be productive. The second section defines additional terms and describes the more technical aspects of the system, and should be used as a reference guide.

A Database Design for a Unit Status Reporting System.

DTIC Science & Technology

1987-03-01

definitions. g. Extraction of data dictionary entries from existing programs. [Ref. 7:pp. 63-66] The third tool is used to define the logic of the...Automation of the Unit Status Reporting System is feasible, and would require: integrated files of data, some direct data extraction from those files...an extract of AR 220-1. Relevant sections of the regulation are included to provide an easy reference for the reader. The last section of the

A Unified Global Reference Frame of Vertical Crustal Movements by Satellite Laser Ranging.

PubMed

Zhu, Xinhui; Wang, Ren; Sun, Fuping; Wang, Jinling

2016-02-08

Crustal movement is one of the main factors influencing the change of the Earth system, especially in its vertical direction, which affects people's daily life through the frequent occurrence of earthquakes, geological disasters, and so on. In order to get a better study and application of the vertical crustal movement,as well as its changes, the foundation and prerequisite areto devise and establish its reference frame; especially, a unified global reference frame is required. Since SLR (satellite laser ranging) is one of the most accurate space techniques for monitoring geocentric motion and can directly measure the ground station's geocentric coordinates and velocities relative to the centre of the Earth's mass, we proposed to take the vertical velocity of the SLR technique in the ITRF2008 framework as the reference frame of vertical crustal motion, which we defined as the SLR vertical reference frame (SVRF). The systematic bias between other velocity fields and the SVRF was resolved by using the GPS (Global Positioning System) and VLBI (very long baseline interferometry) velocity observations, and the unity of other velocity fields and SVRF was realized,as well. The results show that it is feasible and suitable to take the SVRF as a reference frame, which has both geophysical meanings and geodetic observations, so we recommend taking the SLR vertical velocity under ITRF2008 as the global reference frame of vertical crustal movement.

A Unified Global Reference Frame of Vertical Crustal Movements by Satellite Laser Ranging

PubMed Central

Zhu, Xinhui; Wang, Ren; Sun, Fuping; Wang, Jinling

2016-01-01

Crustal movement is one of the main factors influencing the change of the Earth system, especially in its vertical direction, which affects people’s daily life through the frequent occurrence of earthquakes, geological disasters, and so on. In order to get a better study and application of the vertical crustal movement, as well as its changes, the foundation and prerequisite areto devise and establish its reference frame; especially, a unified global reference frame is required. Since SLR (satellite laser ranging) is one of the most accurate space techniques for monitoring geocentric motion and can directly measure the ground station’s geocentric coordinates and velocities relative to the centre of the Earth’s mass, we proposed to take the vertical velocity of the SLR technique in the ITRF2008 framework as the reference frame of vertical crustal motion, which we defined as the SLR vertical reference frame (SVRF). The systematic bias between other velocity fields and the SVRF was resolved by using the GPS (Global Positioning System) and VLBI (very long baseline interferometry) velocity observations, and the unity of other velocity fields and SVRF was realized, as well. The results show that it is feasible and suitable to take the SVRF as a reference frame, which has both geophysical meanings and geodetic observations, so we recommend taking the SLR vertical velocity under ITRF2008 as the global reference frame of vertical crustal movement. PMID:26867197

Fracture risk among older men: osteopenia and osteoporosis defined using cut-points derived from female versus male reference data.

PubMed

Pasco, J A; Lane, S E; Brennan, S L; Timney, E N; Bucki-Smith, G; Dobbins, A G; Nicholson, G C; Kotowicz, M A

2014-03-01

We explored the effect of using male and female reference data in a male sample to categorise areal bone mineral density (BMD). Using male reference data, a large proportion of fractures arose from osteopenia, whereas using female reference data shifted the fracture burden into normal BMD. The purpose of this study was to describe fracture risk associated with osteopenia and osteoporosis in older men, defined by areal BMD and using cut-points derived from male and female reference data. As part of the Geelong Osteoporosis Study, we followed 619 men aged 60-93 years after BMD assessments (performed 2001-2006) until 2010, fracture, death or emigration. Post-baseline fractures were radiologically confirmed, and proportions of fractures in each BMD category were age-standardised to national profiles. Based on World Health Organization criteria, and using male reference data, 207 men had normal BMD at the femoral neck, 357 were osteopenic and 55 were osteoporotic. Using female reference data, corresponding numbers were 361, 227 and 31. During the study, 130 men died, 15 emigrated and 63 sustained at least one fracture. Using male reference data, most (86.5 %) of the fractures occurred in men without osteoporosis on BMD criteria (18.4 % normal BMD, 68.1 % osteopenia). The pattern differed when female reference data were used; while most fractures arose from men without osteoporosis (88.2 %), the burden shifted from those with osteopenia (34.8 %) to those with normal BMD (53.4 %). Decreasing BMD categories defined increasing risk of fracture. Although men with osteoporotic BMD were at greatest risk, they made a relatively small contribution to the total burden of fractures. Using male reference data, two-thirds of the fractures arose from men with osteopenia. However, using female reference data, approximately half of the fractures arose from those with normal BMD. Using female reference data to define osteoporosis in men does not appear to be the optimal approach.

Effect of reference conditions on flow rate, modifier fraction and retention in supercritical fluid chromatography.

PubMed

De Pauw, Ruben; Shoykhet Choikhet, Konstantin; Desmet, Gert; Broeckhoven, Ken

2016-08-12

When using compressible mobile phases such as fluidic CO2, the density, the volumetric flow rates and volumetric fractions are pressure dependent. The pressure and temperature definition of these volumetric parameters (referred to as the reference conditions) may alter between systems, manufacturers and operating conditions. A supercritical fluid chromatography system was modified to operate in two modes with different definition of the eluent delivery parameters, referred to as fixed and variable mode. For the variable mode, the volumetric parameters are defined with reference to the pump operating pressure and actual pump head temperature. These conditions may vary when, e.g. changing the column length, permeability, flow rate, etc. and are thus variable reference conditions. For the fixed mode, the reference conditions were set at 150bar and 30°C, resulting in a mass flow rate and mass fraction of modifier definition which is independent of the operation conditions. For the variable mode, the mass flow rate of carbon dioxide increases with system pump operating pressure, decreasing the fraction of modifier. Comparing the void times and retention factor shows that the deviation between the two modes is almost independent of modifier percentage, but depends on the operating pressure. Recalculating the set volumetric fraction of modifier to the mass fraction results in the same retention behaviour for both modes. This shows that retention in SFC can be best modelled using the mass fraction of modifier. The fixed mode also simplifies method scaling as it only requires matching average column pressure. Copyright © 2016 Elsevier B.V. All rights reserved.

Astrophysics of Reference Frame Tie Objects

NASA Technical Reports Server (NTRS)

Johnston, Kenneth J.; Boboltz, David; Fey, Alan Lee; Gaume, Ralph A.; Zacharias, Norbert

2004-01-01

The Astrophysics of Reference Frame Tie Objects Key Science program will investigate the underlying physics of SIM grid objects. Extragalactic objects in the SIM grid will be used to tie the SIM reference frame to the quasi-inertial reference frame defined by extragalactic objects and to remove any residual frame rotation with respect to the extragalactic frame. The current realization of the extragalactic frame is the International Celestial Reference Frame (ICRF). The ICRF is defined by the radio positions of 212 extragalactic objects and is the IAU sanctioned fundamental astronomical reference frame. This key project will advance our knowledge of the physics of the objects which will make up the SIM grid, such as quasars and chromospherically active stars, and relates directly to the stability of the SIM reference frame. The following questions concerning the physics of reference frame tie objects will be investigated.

A Software Defined Radio Based Airplane Communication Navigation Simulation System

NASA Astrophysics Data System (ADS)

He, L.; Zhong, H. T.; Song, D.

2018-01-01

Radio communication and navigation system plays important role in ensuring the safety of civil airplane in flight. Function and performance should be tested before these systems are installed on-board. Conventionally, a set of transmitter and receiver are needed for each system, thus all the equipment occupy a lot of space and are high cost. In this paper, software defined radio technology is applied to design a common hardware communication and navigation ground simulation system, which can host multiple airplane systems with different operating frequency, such as HF, VHF, VOR, ILS, ADF, etc. We use a broadband analog frontend hardware platform, universal software radio peripheral (USRP), to transmit/receive signal of different frequency band. Software is compiled by LabVIEW on computer, which interfaces with USRP through Ethernet, and is responsible for communication and navigation signal processing and system control. An integrated testing system is established to perform functional test and performance verification of the simulation signal, which demonstrate the feasibility of our design. The system is a low-cost and common hardware platform for multiple airplane systems, which provide helpful reference for integrated avionics design.

Color prediction in textile application

NASA Astrophysics Data System (ADS)

De Lucia, Maurizio; Buonopane, Massimo

2004-09-01

Nowadays production systems of fancy yarns for knits allow the creation of extremely complex products in which many effects are obtained by means of color alteration. Current production technique consists in defining type and quantity of fibers by making preliminary samples. This samples are then compared with a reference one. This comparison is based on operator experience. Many samples are required in order to achieve a sample similar to the reference one. This work requires time and then additional costs for a textile manufacturer. In addition, the methodology is subjective. Nowadays, spectrophotometers are the only devices that seem to be able to provide objective indications. They are based on a spectral analysis of the light reflected by the knit material. In this paper the study of a new method for color evaluation of a mix of wool fibers with different colors is presented. First of all fiber characterization were carried out through scattering and absorption coefficients using the Kubelka-Munk theory. Then the estimated color was compared with a reference item, in order to define conformity by means of objective parameters. Finally, theoretical characterization was compared with the measured quantity. This allowed estimation of prediction quality.

4D Dynamic Required Navigation Performance Final Report

NASA Technical Reports Server (NTRS)

Finkelsztein, Daniel M.; Sturdy, James L.; Alaverdi, Omeed; Hochwarth, Joachim K.

2011-01-01

New advanced four dimensional trajectory (4DT) procedures under consideration for the Next Generation Air Transportation System (NextGen) require an aircraft to precisely navigate relative to a moving reference such as another aircraft. Examples are Self-Separation for enroute operations and Interval Management for in-trail and merging operations. The current construct of Required Navigation Performance (RNP), defined for fixed-reference-frame navigation, is not sufficiently specified to be applicable to defining performance levels of such air-to-air procedures. An extension of RNP to air-to-air navigation would enable these advanced procedures to be implemented with a specified level of performance. The objective of this research effort was to propose new 4D Dynamic RNP constructs that account for the dynamic spatial and temporal nature of Interval Management and Self-Separation, develop mathematical models of the Dynamic RNP constructs, "Required Self-Separation Performance" and "Required Interval Management Performance," and to analyze the performance characteristics of these air-to-air procedures using the newly developed models. This final report summarizes the activities led by Raytheon, in collaboration with GE Aviation and SAIC, and presents the results from this research effort to expand the RNP concept to a dynamic 4D frame of reference.

Epigenetic modifications: basic mechanisms and role in cardiovascular disease (2013 Grover Conference series).

PubMed

Loscalzo, Joseph; Handy, Diane E

2014-06-01

Epigenetics refers to heritable traits that are not a consequence of DNA sequence. Three classes of epigenetic regulation exist: DNA methylation, histone modification, and noncoding RNA action. In the cardiovascular system, epigenetic regulation affects development, differentiation, and disease propensity or expression. Defining the determinants of epigenetic regulation offers opportunities for novel strategies for disease prevention and treatment.

Harry S. Truman Dam and Reservoir, Missouri, Holocene Adaptations Within the Lower Pomme de Terre River Valley, Missouri. Volume 1.

DTIC Science & Technology

1982-06-01

4 Research Design ........... ...................... 6 References ............ ......................... 6 2 VEGETATIONAL...deer herds and, concomitantly, to a procurement 0 system designed to exploit these animals. Thf- was also increased use of aquatic resources, although...34...o ’ design , and attempt to further define those cultural processes through wh ich scit ties articiflate wi th

49 CFR 385.321 - What failures of safety management practices disclosed by the safety audit will result in a...

Code of Federal Regulations, 2011 CFR

2011-10-01

... occurrence. This violation refers to a driver operating a CMV as defined under § 383.5. 9. § 387.7(a... unqualified driver Single occurrence. This violation refers to a driver operating a CMV as defined under § 390...

Mach-zehnder based optical marker/comb generator for streak camera calibration

DOEpatents

Miller, Edward Kirk

2015-03-03

This disclosure is directed to a method and apparatus for generating marker and comb indicia in an optical environment using a Mach-Zehnder (M-Z) modulator. High speed recording devices are configured to record image or other data defining a high speed event. To calibrate and establish time reference, the markers or combs are indicia which serve as timing pulses (markers) or a constant-frequency train of optical pulses (comb) to be imaged on a streak camera for accurate time based calibration and time reference. The system includes a camera, an optic signal generator which provides an optic signal to an M-Z modulator and biasing and modulation signal generators configured to provide input to the M-Z modulator. An optical reference signal is provided to the M-Z modulator. The M-Z modulator modulates the reference signal to a higher frequency optical signal which is output through a fiber coupled link to the streak camera.

Space construction system analysis. Part 2: Platform definition

NASA Technical Reports Server (NTRS)

Hart, R. J.; Myers, H. L.; Abramson, R. D.; Dejong, P. N.; Donavan, R. D.; Greenberg, H. S.; Indrikis, J.; Jandrasi, J. S.; Manoff, M.; Mcbaine, C. K.

1980-01-01

The top level system requirements are summarized and the accompanying conceptual design for an engineering and technology verification platform (ETVP) system is presented. An encompassing statement of the system objectives which drive the system requirements is presented and the major mission and subsystem requirements are described with emphasis on the advanced communications technology mission payload. The platform design is defined and used as a reference configuration for an end to space construction analyses. The preferred construction methods and processes, the important interactions between the platform design and the construction system design and operation, and the technology development efforts required to support the design and space construction of the ETVP are outlined.

SysML: A Language for Space System Engineering

NASA Astrophysics Data System (ADS)

Mazzini, S.; Strangapede, A.

2008-08-01

This paper presents the results of an ESA/ESTEC internal study, performed with the support of INTECS, about modeling languages to support Space System Engineering activities and processes, with special emphasis on system requirements identification and analysis. The study was focused on the assessment of dedicated UML profiles, their positioning alongside the system and software life cycles and associated methodologies. Requirements for a Space System Requirements Language were identified considering the ECSS-E-10 and ECSS-E_40 processes. The study has identified SysML as a very promising language, having as theoretical background the reference system processes defined by the ISO15288, as well as industrial practices.

Considerations for NATO Satellite Communications in the Post 2000 Era (Elements de Reflexion pour les Communications par Satellite dans les Pays Membres de l’OTAN apres l’An 2000),

DTIC Science & Technology

1991-06-01

and Proliferated LEO Systems 243 10 6 Summary Evaluation 243 10.7 Candidate Architectures 244 108 References 245 Appendix 10A. Candidate Orbits for a... biTo develop potential SATCOM system configurations - Mid 1987 Coordination within NATO and including sub-system design issues issue of the Terms of...paragraphs above have been defined using different orbits (c) The systems (geostationary, polar, 12-24-hr inclined at 63’.4 and Low Earth Orbit LEO

Method and system for a network mapping service

DOEpatents

Bynum, Leo

2017-10-17

A method and system of publishing a map includes providing access to a plurality of map data files or mapping services between at least one publisher and at least one subscriber; defining a map in a map context comprising parameters and descriptors to substantially duplicate a map by reference to mutually accessible data or mapping services, publishing a map to a channel in a table file on server; accessing the channel by at least one subscriber, transmitting the mapping context from the server to the at least one subscriber, executing the map context by the at least one subscriber, and generating the map on a display software associated with the at least one subscriber by reconstituting the map from the references and other data in the mapping context.

Remote sensing and the Mississippi high accuracy reference network

NASA Technical Reports Server (NTRS)

Mick, Mark; Alexander, Timothy M.; Woolley, Stan

1994-01-01

Since 1986, NASA's Commercial Remote Sensing Program (CRSP) at Stennis Space Center has supported commercial remote sensing partnerships with industry. CRSP's mission is to maximize U.S. market exploitation of remote sensing and related space-based technologies and to develop advanced technical solutions for spatial information requirements. Observation, geolocation, and communications technologies are converging and their integration is critical to realize the economic potential for spatial informational needs. Global positioning system (GPS) technology enables a virtual revolution in geopositionally accurate remote sensing of the earth. A majority of states are creating GPS-based reference networks, or high accuracy reference networks (HARN). A HARN can be defined for a variety of local applications and tied to aerial or satellite observations to provide an important contribution to geographic information systems (GIS). This paper details CRSP's experience in the design and implementation of a HARN in Mississippi and the design and support of future applications of integrated earth observations, geolocation, and communications technology.

Current Trends and Challenges in Satellite Laser Ranging

NASA Astrophysics Data System (ADS)

Appleby, Graham M.; Bianco, Giuseppe; Noll, Carey E.; Pavlis, Erricos C.; Pearlman, Michael R.

2016-12-01

Satellite Laser Ranging (SLR) is used to measure accurately the distance from ground stations to retro-reflectors on satellites and on the Moon. SLR is one of the fundamental space-geodetic techniques that define the International Terrestrial Reference Frame (ITRF), which is the basis upon which many aspects of global change over space, time, and evolving technology are measured; with VLBI the two techniques define the scale of the ITRF; alone the SLR technique defines its origin (geocenter). The importance of the reference frame has recently been recognized at the inter-governmental level through the United Nations, which adopted in February 2015 the Resolution "Global Geodetic Reference Frame for Sustainable Development." Laser Ranging provides precision orbit determination and instrument calibration and validation for satellite-borne altimeters for the better understanding of sea level change, ocean dynamics, ice mass-balance, and terrestrial topography. It is also a tool to study the dynamics of the Moon and fundamental constants and theories. With the exception of the currently in-orbit GPS constellation, all GNSS satellites now carry retro-reflectors for improved orbit determination, harmonization of reference frames, and in-orbit co-location and system performance validation; the next generation of GPS satellites due for launch from 2019 onwards will also carry retro-reflectors. The ILRS delivers weekly realizations that are accumulated sequentially to extend the ITRF and the Earth Orientation Parameter series with a daily resolution. SLR technology continues to evolve towards the next-generation laser ranging systems and it is expected to successfully meet the challenges of the GGOS2020 program for a future Global Space Geodetic Network. Ranging precision is improving as higher repetition rate, narrower pulse lasers, and faster detectors are implemented within the network. Automation and pass interleaving at some stations is expanding temporal coverage and greatly enhancing efficiency. Discussions are ongoing with some missions that will allow the SLR network stations to provide crucial, but energy-safe, range measurements to optically vulnerable satellites. New retro-reflector designs are improving the signal link and enable daylight ranging that is now the norm for many stations. We discuss many of these laser ranging activities and some of the tough challenges that the SLR network currently faces.

The NIST Real-Time Control System (RCS): A Reference Model Architecture for Computational Intelligence

NASA Technical Reports Server (NTRS)

Albus, James S.

1996-01-01

The Real-time Control System (RCS) developed at NIST and elsewhere over the past two decades defines a reference model architecture for design and analysis of complex intelligent control systems. The RCS architecture consists of a hierarchically layered set of functional processing modules connected by a network of communication pathways. The primary distinguishing feature of the layers is the bandwidth of the control loops. The characteristic bandwidth of each level is determined by the spatial and temporal integration window of filters, the temporal frequency of signals and events, the spatial frequency of patterns, and the planning horizon and granularity of the planners that operate at each level. At each level, tasks are decomposed into sequential subtasks, to be performed by cooperating sets of subordinate agents. At each level, signals from sensors are filtered and correlated with spatial and temporal features that are relevant to the control function being implemented at that level.

The Second Realization of the International Celestial Reference Frame by Very Long Baseline Interferometry

NASA Astrophysics Data System (ADS)

Fey, A. L.; Gordon, D.; Jacobs, C. S.; Ma, C.; Gaume, R. A.; Arias, E. F.; Bianco, G.; Boboltz, D. A.; Böckmann, S.; Bolotin, S.; Charlot, P.; Collioud, A.; Engelhardt, G.; Gipson, J.; Gontier, A.-M.; Heinkelmann, R.; Kurdubov, S.; Lambert, S.; Lytvyn, S.; MacMillan, D. S.; Malkin, Z.; Nothnagel, A.; Ojha, R.; Skurikhina, E.; Sokolova, J.; Souchay, J.; Sovers, O. J.; Tesmer, V.; Titov, O.; Wang, G.; Zharov, V.

2015-08-01

We present the second realization of the International Celestial Reference Frame (ICRF2) at radio wavelengths using nearly 30 years of Very Long Baseline Interferometry observations. ICRF2 contains precise positions of 3414 compact radio astronomical objects and has a positional noise floor of ∼40 μas and a directional stability of the frame axes of ∼10 μas. A set of 295 new “defining” sources was selected on the basis of positional stability and the lack of extensive intrinsic source structure. The positional stability of these 295 defining sources and their more uniform sky distribution eliminates the two greatest weaknesses of the first realization of the International Celestial Reference Frame (ICRF1). Alignment of ICRF2 with the International Celestial Reference System was made using 138 positionally stable sources common to both ICRF2 and ICRF1. The resulting ICRF2 was adopted by the International Astronomical Union as the new fundamental celestial reference frame, replacing ICRF1 as of 2010 January 1.

Error Propagation in the four terrestrial reference frames of the 2022 Modernized National Spatial Reference System

NASA Astrophysics Data System (ADS)

Roman, D. R.; Smith, D. A.

2017-12-01

In 2022, the National Geodetic Survey will replace all three NAD 83 reference frames with four new terrestrial reference frames. Each frame will be named after a tectonic plate (North American, Pacific, Caribbean and Mariana) and each will be related to the IGS frame through three Euler Pole parameters (EPPs). This talk will focus on three main areas of error propagation when defining coordinates in these four frames. Those areas are (1) use of the small angle approximation to relate true rotation about an Euler Pole to small rotations about three Cartesian axes (2) The current state of the art in determining the Euler Poles of these four plates and (3) the combination of both IGS Cartesian coordinate uncertainties and EPP uncertainties into coordinate uncertainties in the four new frames. Discussion will also include recent efforts at improving the Euler Poles for these frames and expected dates when errors in the EPPs will cause an unacceptable level of uncertainty in the four new terrestrial reference frames.

Recursive computer architecture for VLSI

DOE Office of Scientific and Technical Information (OSTI.GOV)

Treleaven, P.C.; Hopkins, R.P.

1982-01-01

A general-purpose computer architecture based on the concept of recursion and suitable for VLSI computer systems built from replicated (lego-like) computing elements is presented. The recursive computer architecture is defined by presenting a program organisation, a machine organisation and an experimental machine implementation oriented to VLSI. The experimental implementation is being restricted to simple, identical microcomputers each containing a memory, a processor and a communications capability. This future generation of lego-like computer systems are termed fifth generation computers by the Japanese. 30 references.

Theoretical and Applied Research in the Field of Higher Geodesy Conducted in Rzeszow

NASA Astrophysics Data System (ADS)

Kadaj, Roman; Świętoń, Tomasz

2016-06-01

Important qualitative changes were taking place in polish geodesy in last few years. It was related to application of new techniques and technologies and to introduction of European reference frames in Poland. New reference stations network ASG-EUPOS, together with Internet services which helps in precise positioning was created. It allows to fast setting up precise hybrid networks. New, accurate satellite networks became the basis of new definitions in the field of reference systems. Simultaneously arise the need of new software, which enables to execute the geodetic works in new technical conditions. Authors had an opportunity to participate in mentioned undertakings, also under the aegis of GUGiK, by creation of methods, algorithms and necessary software tools. In this way the automatic postprocessing module (APPS) in POZGEO service, a part of ASG-EUPOS system came into being. It is an entirely polish product which works in Trimble environment. Universal software for transformation between PLETRF89, PL-ETRF2000, PULKOWO'42 reference systems as well as defined coordinate systems was created (TRANSPOL v. 2.06) and published as open product. An essential functional element of the program is the quasi-geoid model PL-geoid-2011, which has been elaborated by adjustment (calibration) of the global quasi-geoid model EGM2008 to 570 geodetic points (satellite-leveling points). Those and other studies are briefly described in this paper.

Implementation of standardization in clinical practice: not always an easy task.

PubMed

Panteghini, Mauro

2012-02-29

As soon as a new reference measurement system is adopted, clinical validation of correctly calibrated commercial methods should take place. Tracing back the calibration of routine assays to a reference system can actually modify the relation of analyte results to existing reference intervals and decision limits and this may invalidate some of the clinical decision-making criteria currently used. To maintain the accumulated clinical experience, the quantitative relationship to the previous calibration system should be established and, if necessary, the clinical decision-making criteria should be adjusted accordingly. The implementation of standardization should take place in a concerted action of laboratorians, manufacturers, external quality assessment scheme organizers and clinicians. Dedicated meetings with manufacturers should be organized to discuss the process of assay recalibration and studies should be performed to obtain convincing evidence that the standardization works, improving result comparability. Another important issue relates to the surveillance of the performance of standardized assays through the organization of appropriate analytical internal and external quality controls. Last but not least, uncertainty of measurement that fits for this purpose must be defined across the entire traceability chain, starting with the available reference materials, extending through the manufacturers and their processes for assignment of calibrator values and ultimately to the final result reported to clinicians by laboratories.

A Custom Approach for a Flexible, Real-Time and Reliable Software Defined Utility.

PubMed

Zaballos, Agustín; Navarro, Joan; Martín De Pozuelo, Ramon

2018-02-28

Information and communication technologies (ICTs) have enabled the evolution of traditional electric power distribution networks towards a new paradigm referred to as the smart grid. However, the different elements that compose the ICT plane of a smart grid are usually conceived as isolated systems that typically result in rigid hardware architectures, which are hard to interoperate, manage and adapt to new situations. In the recent years, software-defined systems that take advantage of software and high-speed data network infrastructures have emerged as a promising alternative to classic ad hoc approaches in terms of integration, automation, real-time reconfiguration and resource reusability. The purpose of this paper is to propose the usage of software-defined utilities (SDUs) to address the latent deployment and management limitations of smart grids. More specifically, the implementation of a smart grid's data storage and management system prototype by means of SDUs is introduced, which exhibits the feasibility of this alternative approach. This system features a hybrid cloud architecture able to meet the data storage requirements of electric utilities and adapt itself to their ever-evolving needs. Conducted experimentations endorse the feasibility of this solution and encourage practitioners to point their efforts in this direction.

A Custom Approach for a Flexible, Real-Time and Reliable Software Defined Utility

PubMed Central

2018-01-01

Information and communication technologies (ICTs) have enabled the evolution of traditional electric power distribution networks towards a new paradigm referred to as the smart grid. However, the different elements that compose the ICT plane of a smart grid are usually conceived as isolated systems that typically result in rigid hardware architectures, which are hard to interoperate, manage and adapt to new situations. In the recent years, software-defined systems that take advantage of software and high-speed data network infrastructures have emerged as a promising alternative to classic ad hoc approaches in terms of integration, automation, real-time reconfiguration and resource reusability. The purpose of this paper is to propose the usage of software-defined utilities (SDUs) to address the latent deployment and management limitations of smart grids. More specifically, the implementation of a smart grid’s data storage and management system prototype by means of SDUs is introduced, which exhibits the feasibility of this alternative approach. This system features a hybrid cloud architecture able to meet the data storage requirements of electric utilities and adapt itself to their ever-evolving needs. Conducted experimentations endorse the feasibility of this solution and encourage practitioners to point their efforts in this direction. PMID:29495599

Defining Top-of-Atmosphere Flux Reference Level for Earth Radiation Budget Studies

NASA Technical Reports Server (NTRS)

Loeb, N. G.; Kato, S.; Wielicki, B. A.

2002-01-01

To estimate the earth's radiation budget at the top of the atmosphere (TOA) from satellite-measured radiances, it is necessary to account for the finite geometry of the earth and recognize that the earth is a solid body surrounded by a translucent atmosphere of finite thickness that attenuates solar radiation differently at different heights. As a result, in order to account for all of the reflected solar and emitted thermal radiation from the planet by direct integration of satellite-measured radiances, the measurement viewing geometry must be defined at a reference level well above the earth s surface (e.g., 100 km). This ensures that all radiation contributions, including radiation escaping the planet along slant paths above the earth s tangent point, are accounted for. By using a field-of- view (FOV) reference level that is too low (such as the surface reference level), TOA fluxes for most scene types are systematically underestimated by 1-2 W/sq m. In addition, since TOA flux represents a flow of radiant energy per unit area, and varies with distance from the earth according to the inverse-square law, a reference level is also needed to define satellite-based TOA fluxes. From theoretical radiative transfer calculations using a model that accounts for spherical geometry, the optimal reference level for defining TOA fluxes in radiation budget studies for the earth is estimated to be approximately 20 km. At this reference level, there is no need to explicitly account for horizontal transmission of solar radiation through the atmosphere in the earth radiation budget calculation. In this context, therefore, the 20-km reference level corresponds to the effective radiative top of atmosphere for the planet. Although the optimal flux reference level depends slightly on scene type due to differences in effective transmission of solar radiation with cloud height, the difference in flux caused by neglecting the scene-type dependence is less than 0.1%. If an inappropriate TOA flux reference level is used to define satellite TOA fluxes, and horizontal transmission of solar radiation through the planet is not accounted for in the radiation budget equation, systematic errors in net flux of up to 8 W/sq m can result. Since climate models generally use a plane-parallel model approximation to estimate TOA fluxes and the earth radiation budget, they implicitly assume zero horizontal transmission of solar radiation in the radiation budget equation, and do not need to specify a flux reference level. By defining satellite-based TOA flux estimates at a 20-km flux reference level, comparisons with plane-parallel climate model calculations are simplified since there is no need to explicitly correct plane-parallel climate model fluxes for horizontal transmission of solar radiation through a finite earth.

Secure ICCP Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rice, Mark J.; Bonebrake, Christopher A.; Dayley, Greg K.

Inter-Control Center Communications Protocol (ICCP), defined by the IEC 60870-6 TASE.2 standard, was developed to enable data exchange over wide area networks between electric system entities, including utility control centers, Independent System Operators (ISOs), Regional Transmission Operators (RTOs) and Independent Power Producers (IPP) also known as Non-Utility Generators (NUG). ICCP is an unprotected protocol, and as a result is vulnerable to such actions as integrity violation, interception or alteration, spoofing, and eavesdropping. Because of these vulnerabilities with unprotected ICCP communication, security enhancements, referred to as Secure ICCP, have been added and are included in the ICCP products that utilities havemore » received since 2003 when the standard was defined. This has resulted in an ICCP product whose communication can be encrypted and authenticated to address these vulnerabilities.« less

An independent review of the Multi-Path Redundant Avionics Suite (MPRAS) architecture assessment and characterization report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, M.R.

1991-02-01

In recent years the NASA Langley Research Center has funded several contractors to conduct conceptual designs defining architectures for fault tolerant computer systems. Such a system is referred to as a Multi-Path Redundant Avionics Suite (MPRAS), and would form the basis for avionics systems that would be used in future families of space vehicles in a variety of missions. The principal contractors were General Dynamics, Boeing, and Draper Laboratories. These contractors participated in a series of review meetings, and submitted final reports defining their candidate architectures. NASA then commissioned the Research Triangle Institute (RTI) to perform an assessment of thesemore » architectures to identify strengths and weaknesses of each. This report is a separate, independent review of the RTI assessment, done primarily to assure that the assessment was comprehensive and objective. The report also includes general recommendations relative to further MPRAS development.« less

A cloud-based approach for interoperable electronic health records (EHRs).

PubMed

Bahga, Arshdeep; Madisetti, Vijay K

2013-09-01

We present a cloud-based approach for the design of interoperable electronic health record (EHR) systems. Cloud computing environments provide several benefits to all the stakeholders in the healthcare ecosystem (patients, providers, payers, etc.). Lack of data interoperability standards and solutions has been a major obstacle in the exchange of healthcare data between different stakeholders. We propose an EHR system - cloud health information systems technology architecture (CHISTAR) that achieves semantic interoperability through the use of a generic design methodology which uses a reference model that defines a general purpose set of data structures and an archetype model that defines the clinical data attributes. CHISTAR application components are designed using the cloud component model approach that comprises of loosely coupled components that communicate asynchronously. In this paper, we describe the high-level design of CHISTAR and the approaches for semantic interoperability, data integration, and security.

Content-based fused off-axis object illumination direct-to-digital holography

DOEpatents

Price, Jeffery R.

2006-05-02

Systems and methods are described for content-based fused off-axis illumination direct-to-digital holography. A method includes calculating an illumination angle with respect to an optical axis defined by a focusing lens as a function of data representing a Fourier analyzed spatially heterodyne hologram; reflecting a reference beam from a reference mirror at a non-normal angle; reflecting an object beam from an object the object beam incident upon the object at the illumination angle; focusing the reference beam and the object beam at a focal plane of a digital recorder to from the content-based off-axis illuminated spatially heterodyne hologram including spatially heterodyne fringes for Fourier analysis; and digitally recording the content based off-axis illuminated spatially heterodyne hologram including spatially heterodyne fringes for Fourier analysis.

Defining river types in a Mediterranean area: a methodology for the implementation of the EU Water Framework Directive.

PubMed

Munné, Antoni; Prat, Narcís

2004-11-01

The Water Framework Directive (WFD), approved at the end of 2000 by the European Union, proposes the characterization of river types through two classification systems (A and B) (Annex II of the WFD), thereby obtaining comparable reference sites and improving the management of aquatic systems. System A uses fixed categories of three parameters to classify rivers: three altitude ranges, four basin size ranges, and three geological categories. In the other hand, System B proposes to establish river types analyzing different factors considered as obligatory and optional. Here, we tested Systems A and B in the Catalan River Basin District (NE Spain). The application of System A results in 26 river types: 8 in the Pyrenees and 18 in the Iberic-Macaronesian ecoregions. This number would require the establishment of a complex management system and control of the ecological status in a relatively small river basin district. We propose a multivariant system to synthesize the environmental descriptors and to define river types using System B. We use five hydrological, seven morphological, five geological, and two climatic variables to discriminate among river types. This method results in fewer river type categories than System A but is expected to achieve the same degree of differentiation because of the large number of descriptors considered. Two levels are defined in our classification method using System B. Five "river types," defined at large scale (1:1,000,000), are mainly discriminated by annual runoff coefficient, air temperature, and discharge. This level is useful and could facilitate comparisons of results among European river basin districts. The second level defines 10 "subtypes of river management," mainly discriminated by geology in the basin and flow regime. This level is more adequate at local scale (1:250,000) and provides a useful tool for management purposes in relatively small and heterogeneous river basin districts.

Deriving a geocentric reference frame for satellite positioning and navigation

NASA Technical Reports Server (NTRS)

Malla, R. P.; Wu, S.-C.

1988-01-01

With the advent of Earth-orbiting geodetic satellites, nongeocentric datums or reference frames have become things of the past. Accurate geocentric three-dimensional positioning is now possible and is of great importance for various geodetic and oceanographic applications. While relative positioning accuracy of a few centimeters has become a reality using very long baseline interferometry (VLBI), the uncertainty in the offset of the adopted coordinate system origin from the geocenter is still believed to be on the order of 1 meter. Satellite laser ranging (SLR), however, is capable of determining this offset to better than 10 cm, but this is possible only after years of measurements. Global Positioning System (GPS) measurements provide a powerful tool for an accurate determination of this origin offset. Two strategies are discussed. The first strategy utilizes the precise relative positions that were predetermined by VLBI to fix the frame orientation and the absolute scaling, while the offset from the geocenter is determined from GPS measurements. Three different cases are presented under this strategy. The reference frame thus adopted will be consistent with the VLBI coordinate system. The second strategy establishes a reference frame by holding only the longitude of one of the tracking sites fixed. The absolute scaling is determined by the adopted gravitational constant (GM) of the Earth; and the latitude is inferred from the time signature of the Earth rotation in the GPS measurements. The coordinate system thus defined will be a geocentric Earth-fixed coordinate system.

The study of surgical image quality evaluation system by subjective quality factor method

NASA Astrophysics Data System (ADS)

Zhang, Jian J.; Xuan, Jason R.; Yang, Xirong; Yu, Honggang; Koullick, Edouard

2016-03-01

GreenLightTM procedure is an effective and economical way of treatment of benign prostate hyperplasia (BPH); there are almost a million of patients treated with GreenLightTM worldwide. During the surgical procedure, the surgeon or physician will rely on the monitoring video system to survey and confirm the surgical progress. There are a few obstructions that could greatly affect the image quality of the monitoring video, like laser glare by the tissue and body fluid, air bubbles and debris generated by tissue evaporation, and bleeding, just to name a few. In order to improve the physician's visual experience of a laser surgical procedure, the system performance parameter related to image quality needs to be well defined. However, since image quality is the integrated set of perceptions of the overall degree of excellence of an image, or in other words, image quality is the perceptually weighted combination of significant attributes (contrast, graininess …) of an image when considered in its marketplace or application, there is no standard definition on overall image or video quality especially for the no-reference case (without a standard chart as reference). In this study, Subjective Quality Factor (SQF) and acutance are used for no-reference image quality evaluation. Basic image quality parameters, like sharpness, color accuracy, size of obstruction and transmission of obstruction, are used as subparameter to define the rating scale for image quality evaluation or comparison. Sample image groups were evaluated by human observers according to the rating scale. Surveys of physician groups were also conducted with lab generated sample videos. The study shows that human subjective perception is a trustworthy way of image quality evaluation. More systematic investigation on the relationship between video quality and image quality of each frame will be conducted as a future study.

Department of Defense Strategy to Support Multi-Agency Bat Conservation Initiative within the State of Utah

DTIC Science & Technology

2008-02-28

Range, and Section are entered. Datum: Geometric reference surface. Original Site Location datum is defined by user’s map datum; e.g. NAD27...Section are entered. Datum: Geometric reference surface. Original Site Location datum is defined by user’s map datum; e.g. NAD27 Conus or NAD83...Calculated and recorded automatically if the fields UTM_N and UTM_E or Township, Range, and Section are entered. 41 Datum: Geometric reference surface

Five-level emergency triage systems: variation in assessment of validity.

PubMed

Kuriyama, Akira; Urushidani, Seigo; Nakayama, Takeo

2017-11-01

Triage systems are scales developed to rate the degree of urgency among patients who arrive at EDs. A number of different scales are in use; however, the way in which they have been validated is inconsistent. Also, it is difficult to define a surrogate that accurately predicts urgency. This systematic review described reference standards and measures used in previous validation studies of five-level triage systems. We searched PubMed, EMBASE and CINAHL to identify studies that had assessed the validity of five-level triage systems and described the reference standards and measures applied in these studies. Studies were divided into those using criterion validity (reference standards developed by expert panels or triage systems already in use) and those using construct validity (prognosis, costs and resource use). A total of 57 studies examined criterion and construct validity of 14 five-level triage systems. Criterion validity was examined by evaluating (1) agreement between the assigned degree of urgency with objective standard criteria (12 studies), (2) overtriage and undertriage (9 studies) and (3) sensitivity and specificity of triage systems (7 studies). Construct validity was examined by looking at (4) the associations between the assigned degree of urgency and measures gauged in EDs (48 studies) and (5) the associations between the assigned degree of urgency and measures gauged after hospitalisation (13 studies). Particularly, among 46 validation studies of the most commonly used triages (Canadian Triage and Acuity Scale, Emergency Severity Index and Manchester Triage System), 13 and 39 studies examined criterion and construct validity, respectively. Previous studies applied various reference standards and measures to validate five-level triage systems. They either created their own reference standard or used a combination of severity/resource measures. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Design Technology of Advanced Composites.

DTIC Science & Technology

1982-11-01

Communications A.146 Figure 2.-- Conceptual Structure of the Fundamental Protocol Building Block A.147 Figure 3.--External Interactions Associated with a...compatibility between 1544 and 2048 kbit/s system. Annex 5 contains a description of the proposed framwork for distribution to other Study Groups. Some of...are conceptual configurations useful in identifying various possible arrangements to an ISDN. Two concepts are used in defining reference configurations

Coping with Serious Illness: A Conceptual Overview,

DTIC Science & Technology

1980-10-01

conceptualize. Denial has been defined as the effort to negate a problem or situation; avoidance refers to acceptance of the reality of the threat, but...training (Schultz and Luthe, 1969, see Jaffe, 1980), biofeedback (Brown, 1977), exercise (Selye, 1956), hypnosis or self- hypnosis (Kroger, 1977), mental...control, which may in turn positively affect the immune system. -58- Virtually no longitudinal research has been conducted regarding these hypotheses

Integrated Advanced Microwave Sounding Unit-A (AMSU-A). Performance Verification Reports: Final Comprehensive Performance Test Report, P/N: 1356006-1, S.N: 202/A2

NASA Technical Reports Server (NTRS)

Platt, R.

1998-01-01

This is the Performance Verification Report. the process specification establishes the requirements for the comprehensive performance test (CPT) and limited performance test (LPT) of the earth observing system advanced microwave sounding unit-A2 (EOS/AMSU-A2), referred to as the unit. The unit is defined on drawing 1356006.

106-17 Telemetry Standards Chapter 1

DTIC Science & Technology

2017-07-01

Telemetry Standards , RCC Standard 106-17 Chapter 1, July 2017 1-1 CHAPTER 1 Introduction The Telemetry Standards address the here-to-date...generally devoted to a different element of the telemetry system or process . Chapters 21 through 28 address the topic of network telemetry. These...Commonly used terms are defined in standard reference glossaries and dictionaries. Definitions of terms with special applications are included when

Leadership Behaviors of Management for Complex Adaptive Systems

DTIC Science & Technology

2010-04-01

arson • The Five Dysfunctions of a Team - Patrick M. Lencioni Agile Development Practices • Agile Project Management with Scrum – Ken Schwaber...and down to the individual and team level – Relationships are not defined hierarchically, but rather through interactions across References: Mike...n – Consisting of parts intricately combined © Copyright 2009 Northrop GrummanCopyright 2010 Northrop Grumman 5 Predictable or Adaptive Software/IT

Role of the "National Reference Centre for Genetically Modified Organisms (GMO) detection" in the official control of food and feed.

PubMed

Ciabatti, I; Marchesi, U; Froiio, A; Paternò, A; Ruggeri, M; Amaddeo, D

2005-08-01

The National Reference Centre for Genetically Modified Organisms (GMO) detection was established in 2002 within the Istituto Zooprofilattico Sperimentale Lazio e Toscana, with the aim of providing scientific and technical support to the National Health System and to the Ministry of Health within the scope of the regulation of GMO use in food and feed.The recently adopted EU legislation on GMOs (Regulation CE no. 1829/2003 and no. 1830/2003) introduced more rigorous procedures for the authorisation, labelling and analytical control of food and feed consisting, containing or derived from GMOs. The National Reference Centre, besides its institutional tasks as one of the laboratories of the Italian National Health System, collects and analyses data and results of the national official control of GMOs; carries out scientific research aimed at developing, improving, validating and harmonising detection and quantification methods, in cooperation with other scientific institutions, the Community Reference Laboratory and within the European Network of GMOs laboratories (ENGL); collaborates with the Ministry of Health in the definition of control programmes and promotes educational and training initiatives. Objectives defined for 2004-2006, activities in progress and goals already achieved are presented.

Generalized reference fields and source interpolation for the difference formulation of radiation transport

NASA Astrophysics Data System (ADS)

Luu, Thomas; Brooks, Eugene D.; Szőke, Abraham

2010-03-01

In the difference formulation for the transport of thermally emitted photons the photon intensity is defined relative to a reference field, the black body at the local material temperature. This choice of reference field combines the separate emission and absorption terms that nearly cancel, thereby removing the dominant cause of noise in the Monte Carlo solution of thick systems, but introduces time and space derivative source terms that cannot be determined until the end of the time step. The space derivative source term can also lead to noise induced crashes under certain conditions where the real physical photon intensity differs strongly from a black body at the local material temperature. In this paper, we consider a difference formulation relative to the material temperature at the beginning of the time step, or in cases where an alternative temperature better describes the radiation field, that temperature. The result is a method where iterative solution of the material energy equation is efficient and noise induced crashes are avoided. We couple our generalized reference field scheme with an ad hoc interpolation of the space derivative source, resulting in an algorithm that produces the correct flux between zones as the physical system approaches the thick limit.

Scope Complexity Options Risks Excursions (SCORE) Factor Mathematical Description.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gearhart, Jared Lee; Samberson, Jonell Nicole; Shettigar, Subhasini

The purpose of the Scope, Complexity, Options, Risks, Excursions (SCORE) model is to estimate the relative complexity of design variants of future warhead options, resulting in scores. SCORE factors extend this capability by providing estimates of complexity relative to a base system (i.e., all design options are normalized to one weapon system). First, a clearly defined set of scope elements for a warhead option is established. The complexity of each scope element is estimated by Subject Matter Experts (SMEs), including a level of uncertainty, relative to a specific reference system. When determining factors, complexity estimates for a scope element canmore » be directly tied to the base system or chained together via comparable scope elements in a string of reference systems that ends with the base system. The SCORE analysis process is a growing multi-organizational Nuclear Security Enterprise (NSE) effort, under the management of the NA-12 led Enterprise Modeling and Analysis Consortium (EMAC). Historically, it has provided the data elicitation, integration, and computation needed to support the out-year Life Extension Program (LEP) cost estimates included in the Stockpile Stewardship Management Plan (SSMP).« less

Application of the Reference Method Isotope Dilution Gas Chromatography Mass Spectrometry (ID/GC/MS) to Establish Metrological Traceability for Calibration and Control of Blood Glucose Test Systems

PubMed Central

Andreis, Elisabeth; Küllmer, Kai

2014-01-01

Self-monitoring of blood glucose (BG) by means of handheld BG systems is a cornerstone in diabetes therapy. The aim of this article is to describe a procedure with proven traceability for calibration and evaluation of BG systems to guarantee reliable BG measurements. Isotope dilution gas chromatography mass spectrometry (ID/GC/MS) is a method that fulfills all requirements to be used in a higher-order reference measurement procedure. However, this method is not applicable for routine measurements because of the time-consuming sample preparation. A hexokinase method with perchloric acid (PCA) sample pretreatment is used in a measurement procedure for such purposes. This method is directly linked to the ID/GC/MS method by calibration with a glucose solution that has an ID/GC/MS-determined target value. BG systems are calibrated with whole blood samples. The glucose levels in such samples are analyzed by this ID/GC/MS-linked hexokinase method to establish traceability to higher-order reference material. For method comparison, the glucose concentrations in 577 whole blood samples were measured using the PCA-hexokinase method and the ID/GC/MS method; this resulted in a mean deviation of 0.1%. The mean deviation between BG levels measured in >500 valid whole blood samples with BG systems and the ID/GC/MS was 1.1%. BG systems allow a reliable glucose measurement if a true reference measurement procedure, with a noninterrupted traceability chain using ID/GC/MS linked hexokinase method for calibration of BG systems, is implemented. Systems should be calibrated by means of a traceable and defined measurement procedure to avoid bias. PMID:24876614

Automated Detection of Glaucoma From Topographic Features of the Optic Nerve Head in Color Fundus Photographs.

PubMed

Chakrabarty, Lipi; Joshi, Gopal Datt; Chakravarty, Arunava; Raman, Ganesh V; Krishnadas, S R; Sivaswamy, Jayanthi

2016-07-01

To describe and evaluate the performance of an automated CAD system for detection of glaucoma from color fundus photographs. Color fundus photographs of 2252 eyes from 1126 subjects were collected from 2 centers: Aravind Eye Hospital, Madurai and Coimbatore, India. The images of 1926 eyes (963 subjects) were used to train an automated image analysis-based system, which was developed to provide a decision on a given fundus image. A total of 163 subjects were clinically examined by 2 ophthalmologists independently and their diagnostic decisions were recorded. The consensus decision was defined to be the clinical reference (gold standard). Fundus images of eyes with disagreement in diagnosis were excluded from the study. The fundus images of the remaining 314 eyes (157 subjects) were presented to 4 graders and their diagnostic decisions on the same were collected. The performance of the system was evaluated on the 314 images, using the reference standard. The sensitivity and specificity of the system and 4 independent graders were determined against the clinical reference standard. The system achieved an area under receiver operating characteristic curve of 0.792 with a sensitivity of 0.716 and specificity of 0.717 at a selected threshold for the detection of glaucoma. The agreement with the clinical reference standard as determined by Cohen κ is 0.45 for the proposed system. This is comparable to that of the image-based decisions of 4 ophthalmologists. An automated system was presented for glaucoma detection from color fundus photographs. The overall evaluation results indicated that the presented system was comparable in performance to glaucoma classification by a manual grader solely based on fundus image examination.

Space transfer vehicle concepts and requirements. Volume 3: Program cost estimates

NASA Technical Reports Server (NTRS)

1991-01-01

The Space Transfer Vehicle (STV) Concepts and Requirements Study has been an eighteen-month study effort to develop and analyze concepts for a family of vehicles to evolve from an initial STV system into a Lunar Transportation System (LTS) for use with the Heavy Lift Launch Vehicle (HLLV). The study defined vehicle configurations, facility concepts, and ground and flight operations concepts. This volume reports the program cost estimates results for this portion of the study. The STV Reference Concept described within this document provides a complete LTS system that performs both cargo and piloted Lunar missions.

Facial measurements for frame design.

PubMed

Tang, C Y; Tang, N; Stewart, M C

1998-04-01

Anthropometric data for the purpose of spectacle frame design are scarce in the literature. Definitions of facial features to be measured with existing systems of facial measurement are often not specific enough for frame design and manufacturing. Currently, for individual frame design, experienced personnel collect data with facial rules or instruments. A new measuring system is proposed, making use of a template in the form of a spectacle frame. Upon fitting the template onto a subject, most of the measuring references can be defined. Such a system can be administered by lesser-trained personnel and can be used for researches covering a larger population.

Comparing distinct ground-based lightning location networks covering the Netherlands

NASA Astrophysics Data System (ADS)

de Vos, Lotte; Leijnse, Hidde; Schmeits, Maurice; Beekhuis, Hans; Poelman, Dieter; Evers, Läslo; Smets, Pieter

2015-04-01

Lightning can be detected using a ground-based sensor network. The Royal Netherlands Meteorological Institute (KNMI) monitors lightning activity in the Netherlands with the so-called FLITS-system; a network combining SAFIR-type sensors. This makes use of Very High Frequency (VHF) as well as Low Frequency (LF) sensors. KNMI has recently decided to replace FLITS by data from a sub-continental network operated by Météorage which makes use of LF sensors only (KNMI Lightning Detection Network, or KLDN). KLDN is compared to the FLITS system, as well as Met Office's long-range Arrival Time Difference (ATDnet), which measures Very Low Frequency (VLF). Special focus lies on the ability to detect Cloud to Ground (CG) and Cloud to Cloud (CC) lightning in the Netherlands. Relative detection efficiency of individual flashes and lightning activity in a more general sense are calculated over a period of almost 5 years. Additionally, the detection efficiency of each system is compared to a ground-truth that is constructed from flashes that are detected by both of the other datasets. Finally, infrasound data is used as a fourth lightning data source for several case studies. Relative performance is found to vary strongly with location and time. As expected, it is found that FLITS detects significantly more CC lightning (because of the strong aptitude of VHF antennas to detect CC), though KLDN and ATDnet detect more CG lightning. We analyze statistics computed over the entire 5-year period, where we look at CG as well as total lightning (CC and CG combined). Statistics that are considered are the Probability of Detection (POD) and the so-called Lightning Activity Detection (LAD). POD is defined as the percentage of reference flashes the system detects compared to the total detections in the reference. LAD is defined as the fraction of system recordings of one or more flashes in predefined area boxes over a certain time period given the fact that the reference detects at least one flash, compared to the total recordings in the reference dataset. The reference for these statistics is taken to be either another dataset, or a dataset consisting of flashes detected by two datasets. Extreme thunderstorm case evaluation shows that the weather alert criterion for severe thunderstorm is reached by FLITS when this is not the case in KLDN and ATD, suggesting the need for KNMI to modify that weather alert criterion when using KLDN.

Ambulatory estimation of foot placement during walking using inertial sensors.

PubMed

Martin Schepers, H; van Asseldonk, Edwin H F; Baten, Chris T M; Veltink, Peter H

2010-12-01

This study proposes a method to assess foot placement during walking using an ambulatory measurement system consisting of orthopaedic sandals equipped with force/moment sensors and inertial sensors (accelerometers and gyroscopes). Two parameters, lateral foot placement (LFP) and stride length (SL), were estimated for each foot separately during walking with eyes open (EO), and with eyes closed (EC) to analyze if the ambulatory system was able to discriminate between different walking conditions. For validation, the ambulatory measurement system was compared to a reference optical position measurement system (Optotrak). LFP and SL were obtained by integration of inertial sensor signals. To reduce the drift caused by integration, LFP and SL were defined with respect to an average walking path using a predefined number of strides. By varying this number of strides, it was shown that LFP and SL could be best estimated using three consecutive strides. LFP and SL estimated from the instrumented shoe signals and with the reference system showed good correspondence as indicated by the RMS difference between both measurement systems being 6.5 ± 1.0 mm (mean ± standard deviation) for LFP, and 34.1 ± 2.7 mm for SL. Additionally, a statistical analysis revealed that the ambulatory system was able to discriminate between the EO and EC condition, like the reference system. It is concluded that the ambulatory measurement system was able to reliably estimate foot placement during walking. Copyright © 2010 Elsevier Ltd. All rights reserved.

Current Practices of Measuring and Reference Range Reporting of Free and Total Testosterone in the United States.

PubMed

Le, Margaret; Flores, David; May, Danica; Gourley, Eric; Nangia, Ajay K

2016-05-01

The evaluation and management of male hypogonadism should be based on symptoms and on serum testosterone levels. Diagnostically this relies on accurate testing and reference values. Our objective was to define the distribution of reference values and assays for free and total testosterone by clinical laboratories in the United States. Upper and lower reference values, assay methodology and source of published reference ranges were obtained from laboratories across the country. A standardized survey was reviewed with laboratory staff via telephone. Descriptive statistics were used to tabulate results. We surveyed a total of 120 laboratories in 47 states. Total testosterone was measured in house at 73% of laboratories. At the remaining laboratories studies were sent to larger centralized reference facilities. The mean ± SD lower reference value of total testosterone was 231 ± 46 ng/dl (range 160 to 300) and the mean upper limit was 850 ± 141 ng/dl (range 726 to 1,130). Only 9% of laboratories where in-house total testosterone testing was performed created a reference range unique to their region. Others validated the instrument recommended reference values in a small number of internal test samples. For free testosterone 82% of laboratories sent testing to larger centralized reference laboratories where equilibrium dialysis and/or liquid chromatography with mass spectrometry was done. The remaining laboratories used published algorithms to calculate serum free testosterone. Reference ranges for testosterone assays vary significantly among laboratories. The ranges are predominantly defined by limited population studies of men with unknown medical and reproductive histories. These poorly defined and variable reference values, especially the lower limit, affect how clinicians determine treatment. Copyright © 2016 American Urological Association Education and Research, Inc. Published by Elsevier Inc. All rights reserved.

Parasitology tutoring system: a hypermedia computer-based application.

PubMed

Theodoropoulos, G; Loumos, V

1994-02-14

The teaching of parasitology is a basic course in all life sciences curricula, and up to now no computer-assisted tutoring system has been developed for this purpose. By using Knowledge Pro, an object-oriented software development tool, a hypermedia tutoring system for teaching parasitology to college students was developed. Generally, a tutoring system contains a domain expert, a student model, a pedagogical expert and the user interface. In this project, particular emphasis was given to the user interface design and the expert knowledge representation. The system allows access to the educational material through hypermedia and indexing at the pace of the student. The hypermedia access is facilitated through key words defined as hypertext and objects in pictures defined as hyper-areas. The indexing access is based on a list of parameters that refers to various characteristics of the parasites, e.g. taxonomy, host, organ, etc. In addition, this indexing access can be used for testing the student's level of understanding. The advantages of this system are its user-friendliness, graphical interface and ability to incorporate new educational material in the area of parasitology.

The course correction implementation of the inertial navigation system based on the information from the aircraft satellite navigation system before take-off

NASA Astrophysics Data System (ADS)

Markelov, V.; Shukalov, A.; Zharinov, I.; Kostishin, M.; Kniga, I.

2016-04-01

The use of the correction course option before aircraft take-off after inertial navigation system (INS) inaccurate alignment based on the platform attitude-and-heading reference system in azimuth is considered in the paper. A course correction is performed based on the track angle defined by the information received from the satellite navigation system (SNS). The course correction includes a calculated track error definition during ground taxiing along straight sections before take-off with its input in the onboard digital computational system like amendment for using in the current flight. The track error calculation is performed by the statistical evaluation of the track angle comparison defined by the SNS information with the current course measured by INS for a given number of measurements on the realizable time interval. The course correction testing results and recommendation application are given in the paper. The course correction based on the information from SNS can be used for improving accuracy characteristics for determining an aircraft path after making accelerated INS preparation concerning inaccurate initial azimuth alignment.

Commercial D-T FRC Power Plant Systems Analysis

NASA Astrophysics Data System (ADS)

Nguyen, Canh; Santarius, John; Emmert, Gilbert; Steinhauer, Loren; Stubna, Michael

1998-11-01

Results of an engineering issues scoping study of a Field-Reversed Configuration (FRC) burning D-T fuel will be presented. The study primarily focuses on engineering issues, such as tritium-breeding blanket design, radiation shielding, neutron damage, activation, safety, and environment. This presentation will concentrate on plasma physics, current drive, economics, and systems integration, which are important for the overall systems analysis. A systems code serves as the key tool in defining a reference point for detailed physics and engineering calculations plus parametric variations, and typical cases will be presented. Advantages of the cylindrical geometry and high beta (plasma pressure/magnetic-field pressure) are evident.

Knowledge Management and Reference Services

ERIC Educational Resources Information Center

Gandhi, Smiti

2004-01-01

Many corporations are embracing knowledge management (KM) to capture the intellectual capital of their employees. This article focuses on KM applications for reference work in libraries. It defines key concepts of KM, establishes a need for KM for reference services, and reviews various KM initiatives for reference services.

First Definition of Reference Intervals of Liver Function Tests in China: A Large-Population-Based Multi-Center Study about Healthy Adults

PubMed Central

Zhang, Chuanbao; Guo, Wei; Huang, Hengjian; Ma, Yueyun; Zhuang, Junhua; Zhang, Jie

2013-01-01

Background Reference intervals of Liver function tests are very important for the screening, diagnosis, treatment, and monitoring of liver diseases. We aim to establish common reference intervals of liver function tests specifically for the Chinese adult population. Methods A total of 3210 individuals (20–79 years) were enrolled in six representative geographical regions in China. Analytes of ALT, AST, GGT, ALP, total protein, albumin and total bilirubin were measured using three analytical systems mainly used in China. The newly established reference intervals were based on the results of traceability or multiple systems, and then validated in 21 large hospitals located nationwide qualified by the National External Quality Assessment (EQA) of China. Results We had been established reference intervals of the seven liver function tests for the Chinese adult population and found there were apparent variances of reference values for the variables for partitioning analysis such as gender(ALT, GGT, total bilirubin), age(ALP, albumin) and region(total protein). More than 86% of the 21 laboratories passed the validation in all subgroup of reference intervals and overall about 95.3% to 98.8% of the 1220 validation results fell within the range of the new reference interval for all liver function tests. In comparison with the currently recommended reference intervals in China, the single side observed proportions of out of range of reference values from our study for most of the tests deviated significantly from the nominal 2.5% such as total bilirubin (15.2%), ALP (0.2%), albumin (0.0%). Most of reference intervals in our study were obviously different from that of other races. Conclusion These used reference intervals are no longer applicable for the current Chinese population. We have established common reference intervals of liver function tests that are defined specifically for Chinese population and can be universally used among EQA-approved laboratories located all over China. PMID:24058449

Reference Structures: Stagnation, Progress, and Future Challenges.

ERIC Educational Resources Information Center

Greenberg, Jane

1997-01-01

Assesses the current state of reference structures in online public access catalogs (OPACs) in a framework defined by stagnation, progress, and future challenges. Outlines six areas for reference structure development. Twenty figures provide illustrations. (AEF)

78 FR 41132 - Self-Regulatory Organizations; EDGX Exchange, Inc.; Notice of Filing and Immediate Effectiveness...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-09

... Exchange's principal office, and at the Public Reference Room of the Commission. \\3\\ ``Member'' is defined... the Exchange as that term is defined in Section 3(a)(3) of the Act.'' EDGX Rule 1.5(n). \\4\\ References..., then the shares are posted on the EDGX book unless the Member instructs otherwise. See Exchange Rule 11...

Some empirical evidence for ecological dissonance theory.

PubMed

Miller, D I; Verhoek-Miller, N; Giesen, J M; Wells-Parker, E

2000-04-01

Using Festinger's cognitive dissonance theory as a model, the extension to Barker's ecological theory, referred to as ecological dissonance theory, was developed. Designed to examine the motivational dynamics involved when environmental systems are in conflict with each other or with cognitive systems, ecological dissonance theory yielded five propositions which were tested in 10 studies. This summary of the studies suggests operationally defined measures of ecological dissonance may correlate with workers' satisfaction with their jobs, involvement with their jobs, alienation from their work, and to a lesser extent, workers' conflict resolution behavior and communication style.

User's guide to programming fault injection and data acquisition in the SIFT environment

NASA Technical Reports Server (NTRS)

Elks, Carl R.; Green, David F.; Palumbo, Daniel L.

1987-01-01

Described are the features, command language, and functional design of the SIFT (Software Implemented Fault Tolerance) fault injection and data acquisition interface software. The document is also intended to assist and guide the SIFT user in defining, developing, and executing SIFT fault injection experiments and the subsequent collection and reduction of that fault injection data. It is also intended to be used in conjunction with the SIFT User's Guide (NASA Technical Memorandum 86289) for reference to SIFT system commands, procedures and functions, and overall guidance in SIFT system programming.

First Aviation System Technology Advanced Research (AvSTAR) Workshop

NASA Technical Reports Server (NTRS)

Denery, Dallas G. (Editor); Weathers, Del W. (Editor); Rosen, Robert (Technical Monitor); Edwards, Tom (Technical Monitor)

2001-01-01

This Conference Proceedings documents the results of a two-day NASA/FAA/Industry workshop that was held at the NASA Ames Research Center, located at Moffett Field, CA, on September 21-22, 2000. The purpose of the workshop was to bring together a representative cross section of leaders in air traffic management, from industry. FAA, and academia, to assist in defining the requirements for a new research effort, referred to as AvSTAR Aviation Systems Technology Advanced Research). The Conference Proceedings includes the individual presentation, and summarizes the workshop discussions and recommendations.

System for In-Situ Detection of Plant Exposure to Trichloroethylene (TCE)

NASA Technical Reports Server (NTRS)

Newman, Lee A. (Inventor); Lewis, Mark D. (Inventor); Anderson, Daniel J. (Inventor); Keith, Amy G. (Inventor)

2013-01-01

A system detects a plant's exposure to trichloroethylene (TCE) through plant leaf imaging. White light impinging upon a plant's leaf interacts therewith to produce interacted light. A detector is positioned to detect at least one spectral band of the interacted light. A processor coupled to the detector performs comparisons between photonic energy of the interacted light at the one or more spectral bands thereof and reference data defining spectral responses indicative of leaf exposure to TCE. An output device coupled to the processor provides indications of the comparisons.

Life Support Baseline Values and Assumptions Document

NASA Technical Reports Server (NTRS)

Anderson, Molly S.; Ewert, Michael K.; Keener, John F.

2018-01-01

The Baseline Values and Assumptions Document (BVAD) provides analysts, modelers, and other life support researchers with a common set of values and assumptions which can be used as a baseline in their studies. This baseline, in turn, provides a common point of origin from which many studies in the community may depart, making research results easier to compare and providing researchers with reasonable values to assume for areas outside their experience. This document identifies many specific physical quantities that define life support systems, serving as a general reference for spacecraft life support system technology developers.

PACS for surgery and interventional radiology: features of a Therapy Imaging and Model Management System (TIMMS).

PubMed

Lemke, Heinz U; Berliner, Leonard

2011-05-01

Appropriate use of information and communication technology (ICT) and mechatronic (MT) systems is viewed by many experts as a means to improve workflow and quality of care in the operating room (OR). This will require a suitable information technology (IT) infrastructure, as well as communication and interface standards, such as specialized extensions of DICOM, to allow data interchange between surgical system components in the OR. A design of such an infrastructure, sometimes referred to as surgical PACS, but better defined as a Therapy Imaging and Model Management System (TIMMS), will be introduced in this article. A TIMMS should support the essential functions that enable and advance image guided therapy, and in the future, a more comprehensive form of patient-model guided therapy. Within this concept, the "image-centric world view" of the classical PACS technology is complemented by an IT "model-centric world view". Such a view is founded in the special patient modelling needs of an increasing number of modern surgical interventions as compared to the imaging intensive working mode of diagnostic radiology, for which PACS was originally conceptualised and developed. The modelling aspects refer to both patient information and workflow modelling. Standards for creating and integrating information about patients, equipment, and procedures are vitally needed when planning for an efficient OR. The DICOM Working Group 24 (WG-24) has been established to develop DICOM objects and services related to image and model guided surgery. To determine these standards, it is important to define step-by-step surgical workflow practices and create interventional workflow models per procedures or per variable cases. As the boundaries between radiation therapy, surgery and interventional radiology are becoming less well-defined, precise patient models will become the greatest common denominator for all therapeutic disciplines. In addition to imaging, the focus of WG-24 is to serve the therapeutic disciplines by enabling modelling technology to be based on standards. Copyright © 2011. Published by Elsevier Ireland Ltd.

Maritime C2 Strategy: An Innovative Approach to System Transformation

DTIC Science & Technology

2010-04-23

his vision for Information Dominance , reference (a), defining it as: the ability to seize and control the information domain high ground when, where...and however required for decisive competitive advantage across the range of Navy missions. The responsibility for Information Dominance was assigned...to the Director for Information Dominance , a new organization that is the convergence of the former N2 (Intelligence) and N6 (Command, Control and

Intra-Operative Dosimetry in Prostate Brachytherapy

DTIC Science & Technology

2007-11-01

of the focal spot. 2.1. Model for Reconstruction Space Transformation As illustrated in Figure 8, let A & B ( with reference frames FA & FB) be the two...simplex optimization method in MATLAB 7.0 with the search space being defined by the distortion modes from PCA. A linear combination of the modes would...arm is tracked with an X-ray fiducial system called FTRAC that is composed of optimally selected polynomial

Navigation System Design and State Estimation for a Small Rigid Hull Inflatable Boat (RHIB)

DTIC Science & Technology

2014-09-01

addition of the Coriolis term as previously defined has no effect on pitch, only one measurement is compared against Condor’s true pitch angle values...33  B.  REFERENCE FRAME DEFINITIONS ......................................................33  1.  Earth Centered Inertial...the effect of higher order terms. Lastly, the zeroth weight of the scaled weight set can be modified to incorporate prior knowledge of the

Army Science Planning and Strategy Meeting: The Fog of Cyber War

DTIC Science & Technology

2016-12-01

computing , which, depending upon the situation, some refer to as a fog rather than a cloud . These seemingly disparate notions of fog merge when one...Chiang M. CYRUS: towards client- defined cloud storage. Proceedings of the Tenth European Conference on Computer Systems; 2015 Apr 21; Bordeaux...Army Science Planning and Strategy Meeting: The Fog of Cyber War by Alexander Kott and Ananthram Swami Computational and Information Sciences

Magnetic Resonance Characterization of Axonal Response to Spinal Cord Injury

DTIC Science & Technology

2011-10-01

Outcomes 6 Conclusions 6 References 6-29 Appendices Introduction During the first year we pursued studies of Magnetic Resonance q-space imaging...QSI) of the spinal cord and myelin imaging. The QSI studies extended our previous work establishing our ability to define the distribution of axon...Conventional MR imaging of the central nervous systems studies water protons exclusively. Although other compounds, such a lipid and proteins, have

Short Term Innovative Research Program: Nanoengineered Reactive Materials for Tunable Ignition and Energy Release

DTIC Science & Technology

2009-01-01

Background Most conventional explosives can be roughly categorized into two classes – molecular materials and intermolecular composites. Molecular...materials refer to species such as the nitroalkanes (e.g. nitromethane ) and cyclic nitramines (e.g. TNAZ, RDX, HMX) that release chemical energy...alternative to conventional explosives that has been gaining increasing interest have been termed reactive materials, and are defined as systems in

Using Object-Oriented Databases for Implementation of Interactive Electronic Technical Manuals

DTIC Science & Technology

1992-03-01

analytical process applied throughout the system acquisition program in order to define supportability related design factors and to ensure development of a...Node Alternatives Node Alternatives (NODEALTS) is a list of mutually exclusive nodes, grouped together by the fact that they apply to different...contextual situations. The content specific layer NODEALTS element is a reference to a set of nodes that might apply in different situations. No hierarchy

Defining ’Anonymity’ in Networked Communication, Version 1

DTIC Science & Technology

2011-12-01

conference that features many current works on anonymity [5]. 7. References [1] D . Chaum , “Security without Identification: Transaction Systems...to make Big Brother Obsolete,” Communications of the ACM 28:10 (1985), pp. 1030-1044. [2] D . Chaum , “The Dining Cryptographers Problem: Unconditional...Sender and Recipient Untraceability,” Journal of Cryptology 1:1 (1988), pp. 65-75. [3] D . Chaum , “Untraceable Electronic Mail, Return Addresses

Defining datasets and creating data dictionaries for quality improvement and research in chronic disease using routinely collected data: an ontology-driven approach.

PubMed

de Lusignan, Simon; Liaw, Siaw-Teng; Michalakidis, Georgios; Jones, Simon

2011-01-01

The burden of chronic disease is increasing, and research and quality improvement will be less effective if case finding strategies are suboptimal. To describe an ontology-driven approach to case finding in chronic disease and how this approach can be used to create a data dictionary and make the codes used in case finding transparent. A five-step process: (1) identifying a reference coding system or terminology; (2) using an ontology-driven approach to identify cases; (3) developing metadata that can be used to identify the extracted data; (4) mapping the extracted data to the reference terminology; and (5) creating the data dictionary. Hypertension is presented as an exemplar. A patient with hypertension can be represented by a range of codes including diagnostic, history and administrative. Metadata can link the coding system and data extraction queries to the correct data mapping and translation tool, which then maps it to the equivalent code in the reference terminology. The code extracted, the term, its domain and subdomain, and the name of the data extraction query can then be automatically grouped and published online as a readily searchable data dictionary. An exemplar online is: www.clininf.eu/qickd-data-dictionary.html Adopting an ontology-driven approach to case finding could improve the quality of disease registers and of research based on routine data. It would offer considerable advantages over using limited datasets to define cases. This approach should be considered by those involved in research and quality improvement projects which utilise routine data.

[Concepts of development of the neurosurgical operative environment in the 21st century].

PubMed

Apuzzo, M; Liu, C

2002-01-01

The operative environment has to a large extent defines the "state of the art and science" of neurosurgery, which is now undergoing rapid reinvention. In order to remain current, each neurosurgeon should periodically reconsider their personal operative environment and its functional design with reference to modernity of practice as currently defined. Historical trends and their analysis offer predictive guides for development of such settings with an eye toward the future. Examination of technical developments in decade timeframes defines the progress in capability and need. Progressive minimalism of manipulation and the presence of operative definition with increasing precision are evident, with concurrent miniaturization of attendant computerized support systems, sensors, robotic interfaces, and imaging devices. These trends and developments offer the opportunity for simplificity of setting design with higher functionality as the desired endpoint.

Advanced Techniques for Deploying Reliable and Efficient Access Control: Application to E-healthcare.

PubMed

Jaïdi, Faouzi; Labbene-Ayachi, Faten; Bouhoula, Adel

2016-12-01

Nowadays, e-healthcare is a main advancement and upcoming technology in healthcare industry that contributes to setting up automated and efficient healthcare infrastructures. Unfortunately, several security aspects remain as main challenges towards secure and privacy-preserving e-healthcare systems. From the access control perspective, e-healthcare systems face several issues due to the necessity of defining (at the same time) rigorous and flexible access control solutions. This delicate and irregular balance between flexibility and robustness has an immediate impact on the compliance of the deployed access control policy. To address this issue, the paper defines a general framework to organize thinking about verifying, validating and monitoring the compliance of access control policies in the context of e-healthcare databases. We study the problem of the conformity of low level policies within relational databases and we particularly focus on the case of a medical-records management database defined in the context of a Medical Information System. We propose an advanced solution for deploying reliable and efficient access control policies. Our solution extends the traditional lifecycle of an access control policy and allows mainly managing the compliance of the policy. We refer to an example to illustrate the relevance of our proposal.

Advanced extravehicular activity systems requirements definition study

NASA Technical Reports Server (NTRS)

1988-01-01

A study to define the requirements for advanced extravehicular activities (AEVA) was conducted. The purpose of the study was to develop an understanding of the EVA technology requirements and to map a pathway from existing or developing technologies to an AEVA system capable of supporting long-duration missions on the lunar surface. The parameters of an AEVA system which must sustain the crewmembers and permit productive work for long periods in the lunar environment were examined. A design reference mission (DRM) was formulated and used as a tool to develop and analyze the EVA systems technology aspects. Many operational and infrastructure design issues which have a significant influence on the EVA system are identified.

Automated extraction of knowledge for model-based diagnostics

NASA Technical Reports Server (NTRS)

Gonzalez, Avelino J.; Myler, Harley R.; Towhidnejad, Massood; Mckenzie, Frederic D.; Kladke, Robin R.

1990-01-01

The concept of accessing computer aided design (CAD) design databases and extracting a process model automatically is investigated as a possible source for the generation of knowledge bases for model-based reasoning systems. The resulting system, referred to as automated knowledge generation (AKG), uses an object-oriented programming structure and constraint techniques as well as internal database of component descriptions to generate a frame-based structure that describes the model. The procedure has been designed to be general enough to be easily coupled to CAD systems that feature a database capable of providing label and connectivity data from the drawn system. The AKG system is capable of defining knowledge bases in formats required by various model-based reasoning tools.

The software-defined fast post-processing for GEM soft x-ray diagnostics in the Tungsten Environment in Steady-state Tokamak thermal fusion reactor

NASA Astrophysics Data System (ADS)

Krawczyk, Rafał Dominik; Czarski, Tomasz; Linczuk, Paweł; Wojeński, Andrzej; Kolasiński, Piotr; GÄ ska, Michał; Chernyshova, Maryna; Mazon, Didier; Jardin, Axel; Malard, Philippe; Poźniak, Krzysztof; Kasprowicz, Grzegorz; Zabołotny, Wojciech; Kowalska-Strzeciwilk, Ewa; Malinowski, Karol

2018-06-01

This article presents a novel software-defined server-based solutions that were introduced in the fast, real-time computation systems for soft X-ray diagnostics for the WEST (Tungsten Environment in Steady-state Tokamak) reactor in Cadarache, France. The objective of the research was to provide a fast processing of data at high throughput and with low latencies for investigating the interplay between the particle transport and magnetohydrodynamic activity. The long-term objective is to implement in the future a fast feedback signal in the reactor control mechanisms to sustain the fusion reaction. The implemented electronic measurement device is anticipated to be deployed in the WEST. A standalone software-defined computation engine was designed to handle data collected at high rates in the server back-end of the system. Signals are obtained from the front-end field-programmable gate array mezzanine cards that acquire and perform a selection from the gas electron multiplier detector. A fast, authorial library for plasma diagnostics was written in C++. It originated from reference offline MATLAB implementations. They were redesigned for runtime analysis during the experiment in the novel online modes of operation. The implementation allowed the benchmarking, evaluation, and optimization of plasma processing algorithms with the possibility to check the consistency with reference computations written in MATLAB. The back-end software and hardware architecture are presented with data evaluation mechanisms. The online modes of operation for the WEST are discussed. The results concerning the performance of the processing and the introduced functionality are presented.

Single-cell systems level analysis of human Toll-Like-Receptor activation defines a chemokine signature in Systemic Lupus Erythematosus

PubMed Central

O'Gorman, William E.; Hsieh, Elena W.Y.; Savig, Erica S.; Gherardini, Pier Federico; Hernandez, Joseph D.; Hansmann, Leo; Balboni, Imelda M.; Utz, Paul J.; Bendall, Sean C.; Fantl, Wendy J.; Lewis, David B.; Nolan, Garry P.; Davis, Mark M.

2015-01-01

Background Activation of Toll-Like Receptors (TLRs) induces inflammatory responses involved in immunity to pathogens and autoimmune pathogenesis, such as in Systemic Lupus Erythematosus (SLE). Although TLRs are differentially expressed across the immune system, a comprehensive analysis of how multiple immune cell subsets respond in a system-wide manner has previously not been described. Objective To characterize TLR activation across multiple immune cell subsets and individuals, with the goal of establishing a reference framework against which to compare pathological processes. Methods Peripheral whole blood samples were stimulated with TLR ligands, and analyzed by mass cytometry simultaneously for surface marker expression, activation states of intracellular signaling proteins, and cytokine production. We developed a novel data visualization tool to provide an integrated view of TLR signaling networks with single-cell resolution. We studied seventeen healthy volunteer donors and eight newly diagnosed untreated SLE patients. Results Our data revealed the diversity of TLR-induced responses within cell types, with TLR ligand specificity. Subsets of NK and T cells selectively induced NF-κB in response to TLR2 ligands. CD14hi monocytes exhibited the most polyfunctional cytokine expression patterns, with over 80 distinct cytokine combinations. Monocytic TLR-induced cytokine patterns were shared amongst a group of healthy donors, with minimal intra- and inter- individual variability. Furthermore, autoimmune disease altered baseline cytokine production, as newly diagnosed untreated SLE patients shared a distinct monocytic chemokine signature, despite clinical heterogeneity. Conclusion Mass cytometry analysis defined a systems-level reference framework for human TLR activation, which can be applied to study perturbations in inflammatory disease, such as SLE. PMID:26037552

Location memory biases reveal the challenges of coordinating visual and kinesthetic reference frames

PubMed Central

Simmering, Vanessa R.; Peterson, Clayton; Darling, Warren; Spencer, John P.

2008-01-01

Five experiments explored the influence of visual and kinesthetic/proprioceptive reference frames on location memory. Experiments 1 and 2 compared visual and kinesthetic reference frames in a memory task using visually-specified locations and a visually-guided response. When the environment was visible, results replicated previous findings of biases away from the midline symmetry axis of the task space, with stability for targets aligned with this axis. When the environment was not visible, results showed some evidence of bias away from a kinesthetically-specified midline (trunk anterior–posterior [a–p] axis), but there was little evidence of stability when targets were aligned with body midline. This lack of stability may reflect the challenges of coordinating visual and kinesthetic information in the absence of an environmental reference frame. Thus, Experiments 3–5 examined kinesthetic guidance of hand movement to kinesthetically-defined targets. Performance in these experiments was generally accurate with no evidence of consistent biases away from the trunk a–p axis. We discuss these results in the context of the challenges of coordinating reference frames within versus between multiple sensori-motor systems. PMID:17703284

Identification of Reference Genes in Human Myelomonocytic Cells for Gene Expression Studies in Altered Gravity

PubMed Central

Thiel, Cora S.; Hauschild, Swantje; Tauber, Svantje; Paulsen, Katrin; Raig, Christiane; Raem, Arnold; Biskup, Josefine; Gutewort, Annett; Hürlimann, Eva; Philpot, Claudia; Lier, Hartwin; Engelmann, Frank; Layer, Liliana E.

2015-01-01

Gene expression studies are indispensable for investigation and elucidation of molecular mechanisms. For the process of normalization, reference genes (“housekeeping genes”) are essential to verify gene expression analysis. Thus, it is assumed that these reference genes demonstrate similar expression levels over all experimental conditions. However, common recommendations about reference genes were established during 1 g conditions and therefore their applicability in studies with altered gravity has not been demonstrated yet. The microarray technology is frequently used to generate expression profiles under defined conditions and to determine the relative difference in expression levels between two or more different states. In our study, we searched for potential reference genes with stable expression during different gravitational conditions (microgravity, normogravity, and hypergravity) which are additionally not altered in different hardware systems. We were able to identify eight genes (ALB, B4GALT6, GAPDH, HMBS, YWHAZ, ABCA5, ABCA9, and ABCC1) which demonstrated no altered gene expression levels in all tested conditions and therefore represent good candidates for the standardization of gene expression studies in altered gravity. PMID:25654098

Identification of reference genes in human myelomonocytic cells for gene expression studies in altered gravity.

PubMed

Thiel, Cora S; Hauschild, Swantje; Tauber, Svantje; Paulsen, Katrin; Raig, Christiane; Raem, Arnold; Biskup, Josefine; Gutewort, Annett; Hürlimann, Eva; Unverdorben, Felix; Buttron, Isabell; Lauber, Beatrice; Philpot, Claudia; Lier, Hartwin; Engelmann, Frank; Layer, Liliana E; Ullrich, Oliver

2015-01-01

Gene expression studies are indispensable for investigation and elucidation of molecular mechanisms. For the process of normalization, reference genes ("housekeeping genes") are essential to verify gene expression analysis. Thus, it is assumed that these reference genes demonstrate similar expression levels over all experimental conditions. However, common recommendations about reference genes were established during 1 g conditions and therefore their applicability in studies with altered gravity has not been demonstrated yet. The microarray technology is frequently used to generate expression profiles under defined conditions and to determine the relative difference in expression levels between two or more different states. In our study, we searched for potential reference genes with stable expression during different gravitational conditions (microgravity, normogravity, and hypergravity) which are additionally not altered in different hardware systems. We were able to identify eight genes (ALB, B4GALT6, GAPDH, HMBS, YWHAZ, ABCA5, ABCA9, and ABCC1) which demonstrated no altered gene expression levels in all tested conditions and therefore represent good candidates for the standardization of gene expression studies in altered gravity.

Linking HIPPARCOS to the Extragalactic Reference Frame Part 5 OF 6, Newc, Cycle 2,CONTINUATION of 2565-HIGH

NASA Astrophysics Data System (ADS)

Hemenway, Paul

1991-07-01

Determination of a non-rotating Reference Frame is crucial to progress in many areas, including: Galactic motions, local (Oort's A and B) and global (R0) parameters derived from them, solar system motion discrepancies (Planet X); and in conjunction with the VLBI radio reference frame, the registration of radio and optical images at an accuracy well below the resolution limit of HST images (0.06 arcsec). The goal of the Program is to tie the HIPPARCOS and Extra- galactic Reference Frames together at the 0.0005 arcsec and 0.0005 arcsec/year level. The HST data will allow a deter- mination of the brightness distribution in the stellar and extragalactic objects observed and time dependent changes therein at the 0.001 arcsec/year level. The Program requires targets distributed over the whole sky to define a rigid Reference Frame. GTO observations will provide initial first epoch data and preliminary proper motions. The observations will consist of relative positions of Extra- galactic objects (EGOs) and HIPPARCOS stars, measured with the FGSs.

Spacecraft attitude calibration/verification baseline study

NASA Technical Reports Server (NTRS)

Chen, L. C.

1981-01-01

A baseline study for a generalized spacecraft attitude calibration/verification system is presented. It can be used to define software specifications for three major functions required by a mission: the pre-launch parameter observability and data collection strategy study; the in-flight sensor calibration; and the post-calibration attitude accuracy verification. Analytical considerations are given for both single-axis and three-axis spacecrafts. The three-axis attitudes considered include the inertial-pointing attitudes, the reference-pointing attitudes, and attitudes undergoing specific maneuvers. The attitude sensors and hardware considered include the Earth horizon sensors, the plane-field Sun sensors, the coarse and fine two-axis digital Sun sensors, the three-axis magnetometers, the fixed-head star trackers, and the inertial reference gyros.

Development and Reliability Testing of the FEDS System for Classifying Glenohumeral Instability

PubMed Central

Kuhn, John E.; Helmer, Tara T.; Dunn, Warren R.; Throckmorton V, Thomas W.

2010-01-01

Background Classification systems for glenohumeral instability (GHI) are opinion based, not validated, and poorly defined. This study is designed to methodologically develop and test a GHI classification system. Methods: Classification System Development A systematic literature review identified 18 systems for classifying GHI. The frequency characteristics used was recorded. Additionally 31 members of the American Shoulder and Elbow Surgeons responded to a survey to identify features important to characterize GHI. Frequency, Etiology, Direction, and Severity (FEDS), were found to be most important. Frequency was defined as solitary (one episode), occasional (2–5x/year), or frequent (>5x/year). Etiology was defined as traumatic or atraumatic. Direction referred to the primary direction of instability (anterior, posterior, or inferior). Severity was defined as either subluxation or dislocation. Methods: Reliability Testing Fifty GHI patients completed a questionnaire at their initial visit. One of six sports medicine fellowship trained physicians completed a similar questionnaire after examining the patient. Patients returned after two weeks and were examined by the original physician and two other physicians. Inter- and intra-rater agreement for the FEDS classification system was calculated. Results Agreement between patients and physicians was lowest for frequency (39%; k=0.130) and highest for direction (82%; k=0.636). Physician intra-rater agreement was 84– 97% for the individual FEDS characteristics (k=0.69 to 0.87)). Physician inter-rater agreement ranged from 82–90% (k=0.44 to 0.76). Conclusions The FEDS system has content validity and is highly reliable for classifying GHI. Physical examination using provocative testing to determine the primary direction of instability produces very high levels of inter- and intra-rater agreement. Level of evidence Level II, Development of Diagnostic Criteria with Consecutive Series of Patients, Diagnosis Study. PMID:21277809

A reference aerosol for a radon reference chamber

NASA Astrophysics Data System (ADS)

Paul, Annette; Keyser, Uwe

1996-02-01

The measurement of radon and radon progenies and the calibration of their detection systems require the production and measurement of aerosols well-defined in size and concentration. In the German radon reference chamber, because of its unique chemical and physical properties, carnauba wax is used to produce standard aerosols. The aerosol size spectra are measured on-line by an aerosol measurement system in the range of 10 nm to 1 μm aerodynamic diameter. The experimental set-ups for the study of adsorption of radioactive ions on aerosols as function of their size and concentration will be described, the results presented and further adaptations for an aerosol jet introduced (for example, for the measurement of short-lived neutron-rich isotopes). Data on the dependence of aerosol radius, ion concentration and element selectivity is collected by using a 252Cf-sf source. The fission products of this source range widely in elements, isotopes and charges. Adsorption and the transport of radioactive ions on aerosols have therefore been studied for various ions for the first time, simultaneously with the aerosol size on-line spectrometry.

Factors influencing humanitarian care and the treatment of local patients within the deployed military medical system: casualty referral limitations.

PubMed

Causey, Marlin; Rush, Robert M; Kjorstad, Randy J; Sebesta, James A

2012-05-01

Humanitarian medical care is an essential task of the deployed military health care system. The purpose of this study was to analyze referral acceptance in treating injured local national patients during Operation Enduring Freedom. A prospective observation study of local nationals who were referred for humanitarian trauma care in Afghanistan from March through August 2009. Sixty-six patients were referred for evacuation for suspected non-coalition-caused injuries. The bed status at the receiving hospital was defined as green (able to accept patients), amber (nearing capacity), and red (at capacity). The only factor associated with acceptance was the accepting hospital bed status (odds ratio = 1.57%, 95% confidence interval, 1.11-2.22; P = .009). Factors not significant were age, the province of origin, the type of referring facility, a prior operation before the request, patient status/affiliation, or the mechanism of injury. Humanitarian medical care is directly related to the capacity for high-acuity care because bed availability is the predominate reason for acceptance or rejection. Published by Elsevier Inc.

Reference set for performance testing of pediatric vaccine safety signal detection methods and systems.

PubMed

Brauchli Pernus, Yolanda; Nan, Cassandra; Verstraeten, Thomas; Pedenko, Mariia; Osokogu, Osemeke U; Weibel, Daniel; Sturkenboom, Miriam; Bonhoeffer, Jan

2016-12-12

Safety signal detection in spontaneous reporting system databases and electronic healthcare records is key to detection of previously unknown adverse events following immunization. Various statistical methods for signal detection in these different datasources have been developed, however none are geared to the pediatric population and none specifically to vaccines. A reference set comprising pediatric vaccine-adverse event pairs is required for reliable performance testing of statistical methods within and across data sources. The study was conducted within the context of the Global Research in Paediatrics (GRiP) project, as part of the seventh framework programme (FP7) of the European Commission. Criteria for the selection of vaccines considered in the reference set were routine and global use in the pediatric population. Adverse events were primarily selected based on importance. Outcome based systematic literature searches were performed for all identified vaccine-adverse event pairs and complemented by expert committee reports, evidence based decision support systems (e.g. Micromedex), and summaries of product characteristics. Classification into positive (PC) and negative control (NC) pairs was performed by two independent reviewers according to a pre-defined algorithm and discussed for consensus in case of disagreement. We selected 13 vaccines and 14 adverse events to be included in the reference set. From a total of 182 vaccine-adverse event pairs, we classified 18 as PC, 113 as NC and 51 as unclassifiable. Most classifications (91) were based on literature review, 45 were based on expert committee reports, and for 46 vaccine-adverse event pairs, an underlying pathomechanism was not plausible classifying the association as NC. A reference set of vaccine-adverse event pairs was developed. We propose its use for comparing signal detection methods and systems in the pediatric population. Published by Elsevier Ltd.

Use of diagnostic accuracy as a metric for evaluating laboratory proficiency with microarray assays using mixed-tissue RNA reference samples.

PubMed

Pine, P S; Boedigheimer, M; Rosenzweig, B A; Turpaz, Y; He, Y D; Delenstarr, G; Ganter, B; Jarnagin, K; Jones, W D; Reid, L H; Thompson, K L

2008-11-01

Effective use of microarray technology in clinical and regulatory settings is contingent on the adoption of standard methods for assessing performance. The MicroArray Quality Control project evaluated the repeatability and comparability of microarray data on the major commercial platforms and laid the groundwork for the application of microarray technology to regulatory assessments. However, methods for assessing performance that are commonly applied to diagnostic assays used in laboratory medicine remain to be developed for microarray assays. A reference system for microarray performance evaluation and process improvement was developed that includes reference samples, metrics and reference datasets. The reference material is composed of two mixes of four different rat tissue RNAs that allow defined target ratios to be assayed using a set of tissue-selective analytes that are distributed along the dynamic range of measurement. The diagnostic accuracy of detected changes in expression ratios, measured as the area under the curve from receiver operating characteristic plots, provides a single commutable value for comparing assay specificity and sensitivity. The utility of this system for assessing overall performance was evaluated for relevant applications like multi-laboratory proficiency testing programs and single-laboratory process drift monitoring. The diagnostic accuracy of detection of a 1.5-fold change in signal level was found to be a sensitive metric for comparing overall performance. This test approaches the technical limit for reliable discrimination of differences between two samples using this technology. We describe a reference system that provides a mechanism for internal and external assessment of laboratory proficiency with microarray technology and is translatable to performance assessments on other whole-genome expression arrays used for basic and clinical research.

A mathematical representation of an advanced helicopter for piloted simulator investigations of control system and display variations

NASA Technical Reports Server (NTRS)

Aiken, E. W.

1980-01-01

A mathematical model of an advanced helicopter is described. The model is suitable for use in control/display research involving piloted simulation. The general design approach for the six degree of freedom equations of motion is to use the full set of nonlinear gravitational and inertial terms of the equations and to express the aerodynamic forces and moments as the reference values and first order terms of a Taylor series expansion about a reference trajectory defined as a function of longitudinal airspeed. Provisions for several different specific and generic flight control systems are included in the model. The logic required to drive various flight control and weapon delivery symbols on a pilot's electronic display is also provided. Finally, the model includes a simplified representation of low altitude wind and turbulence effects. This model was used in a piloted simulator investigation of the effects of control system and display variations for an attack helicopter mission.

Technical Reference Suite Addressing Challenges of Providing Assurance for Fault Management Architectural Design

NASA Technical Reports Server (NTRS)

Fitz, Rhonda; Whitman, Gerek

2016-01-01

Research into complexities of software systems Fault Management (FM) and how architectural design decisions affect safety, preservation of assets, and maintenance of desired system functionality has coalesced into a technical reference (TR) suite that advances the provision of safety and mission assurance. The NASA Independent Verification and Validation (IVV) Program, with Software Assurance Research Program support, extracted FM architectures across the IVV portfolio to evaluate robustness, assess visibility for validation and test, and define software assurance methods applied to the architectures and designs. This investigation spanned IVV projects with seven different primary developers, a wide range of sizes and complexities, and encompassed Deep Space Robotic, Human Spaceflight, and Earth Orbiter mission FM architectures. The initiative continues with an expansion of the TR suite to include Launch Vehicles, adding the benefit of investigating differences intrinsic to model-based FM architectures and insight into complexities of FM within an Agile software development environment, in order to improve awareness of how nontraditional processes affect FM architectural design and system health management.

Examination of a Method to Determine the Reference Region for Calculating the Specific Binding Ratio in Dopamine Transporter Imaging.

PubMed

Watanabe, Ayumi; Inoue, Yusuke; Asano, Yuji; Kikuchi, Kei; Miyatake, Hiroki; Tokushige, Takanobu

2017-01-01

The specific binding ratio (SBR) was first reported by Tossici-Bolt et al. for quantitative indicators for dopamine transporter (DAT) imaging. It is defined as the ratio of the specific binding concentration of the striatum to the non-specific binding concentration of the whole brain other than the striatum. The non-specific binding concentration is calculated based on the region of interest (ROI), which is set 20 mm inside the outer contour, defined by a threshold technique. Tossici-Bolt et al. used a 50% threshold, but sometimes we couldn't define the ROI of non-specific binding concentration (reference region) and calculate SBR appropriately with a 50% threshold. Therefore, we sought a new method for determining the reference region when calculating SBR. We used data from 20 patients who had undergone DAT imaging in our hospital, to calculate the non-specific binding concentration by the following methods, the threshold to define a reference region was fixed at some specific values (the fixing method) and reference region was visually optimized by an examiner at every examination (the visual optimization method). First, we assessed the reference region of each method visually, and afterward, we quantitatively compared SBR calculated based on each method. In the visual assessment, the scores of the fixing method at 30% and visual optimization method were higher than the scores of the fixing method at other values, with or without scatter correction. In the quantitative assessment, the SBR obtained by visual optimization of the reference region, based on consensus of three radiological technologists, was used as a baseline (the standard method). The values of SBR showed good agreement between the standard method and both the fixing method at 30% and the visual optimization method, with or without scatter correction. Therefore, the fixing method at 30% and the visual optimization method were equally suitable for determining the reference region.

The Swedish strategy and method for development of a national healthcare information architecture.

PubMed

Rosenälv, Jessica; Lundell, Karl-Henrik

2012-01-01

"We need a precise framework of regulations in order to maintain appropriate and structured health care documentation that ensures that the information maintains a sufficient level of quality to be used in treatment, in research and by the actual patient. The users shall be aided by clearly and uniformly defined terms and concepts, and there should be an information structure that clarifies what to document and how to make the information more useful. Most of all, we need to standardize the information, not just the technical systems." (eHälsa - nytta och näring, Riksdag report 2011/12:RFR5, p. 37). In 2010, the Swedish Government adopted the National e-Health - the national strategy for accessible and secure information in healthcare. The strategy is a revision and extension of the previous strategy from 2006, which was used as input for the most recent efforts to develop a national information structure utilizing business-oriented generic models. A national decision on healthcare informatics standards was made by the Swedish County Councils, which decided to follow and use EN/ISO 13606 as a standard for the development of a universally applicable information structure, including archetypes and templates. The overall aim of the Swedish strategy for development of National Healthcare Information Architecture is to achieve high level semantic interoperability for clinical content and clinical contexts. High level semantic interoperability requires consistently structured clinical data and other types of data with coherent traceability to be mapped to reference clinical models. Archetypes that are formal definitions of the clinical and demographic concepts and some administrative data were developed. Each archetype describes the information structure and content of overarching core clinical concepts. Information that is defined in archetypes should be used for different purposes. Generic clinical process model was made concrete and analyzed. For each decision-making step in the process where information is processed, the amount and type of information and its structure were defined in terms of reference templates. Reference templates manage clinical, administrative and demographic types of information in a specific clinical context. Based on a survey of clinical processes at the reference level, the identification of specific clinical processes such as diabetes and congestive heart failure in adults were made. Process-specific templates were defined by using reference templates and populated with information that was relevant to each health problem in a specific clinical context. Throughout this process, medical data for knowledge management were collected for each health problem. Parallel with the efforts to define archetypes and templates, terminology binding work is on-going. Different strategies are used depending on the terminology binding level.

Harmonization in laboratory medicine: Requests, samples, measurements and reports.

PubMed

Plebani, Mario

2016-01-01

In laboratory medicine, the terms "standardization" and "harmonization" are frequently used interchangeably as the final goal is the same: the equivalence of measurement results among different routine measurement procedures over time and space according to defined analytical and clinical quality specifications. However, the terms define two distinct, albeit closely linked, concepts based on traceability principles. The word "standardization" is used when results for a measurement are equivalent and traceable to the International System of Units (SI) through a high-order primary reference material and/or a reference measurement procedure (RMP). "Harmonization" is generally used when results are equivalent, but neither a high-order primary reference material nor a reference measurement procedure is available. Harmonization is a fundamental aspect of quality in laboratory medicine as its ultimate goal is to improve patient outcomes through the provision of accurate and actionable laboratory information. Patients, clinicians and other healthcare professionals assume that clinical laboratory tests performed by different laboratories at different times on the same sample and specimen can be compared, and that results can be reliably and consistently interpreted. Unfortunately, this is not necessarily the case, because many laboratory test results are still highly variable and poorly standardized and harmonized. Although the initial focus was mainly on harmonizing and standardizing analytical processes and methods, the scope of harmonization now also includes all other aspects of the total testing process (TTP), such as terminology and units, report formats, reference intervals and decision limits as well as tests and test profiles, requests and criteria for interpretation. Several projects and initiatives aiming to improve standardization and harmonization in the testing process are now underway. Laboratory professionals should therefore step up their efforts to provide interchangeable and comparable laboratory information in order to ultimately assure better diagnosis and treatment in patient care.

Linked Orders Improve Safety in Scheduling and Administration of Chemotherapeutic Agents

PubMed Central

Whipple, Nancy; Boulware, Joy; Danca, Kala; Boyarin, Kirill; Ginsberg, Eliot; Poon, Eric; Sweet, Micheal; Schade, Sue; Rogala, Jennifer

2010-01-01

The pharmacologic treatment for cancer must adhere to complex, finely orchestrated treatment plans, including not only chemotherapy medications, but pre/post-hydration, anti-emetics, anti-anxiety, and other medications that are given before, during and after chemotherapy doses. The treatment plans specify the medications and dictate precise dosing, frequency, and timing. This is a challenge to most Computerized Physician Order Entry (CPOE), Pharmacy and Electronic Medication Administration record (eMAR) Systems. Medications are scheduled on specific dates, referred to as chemo days, from the onset of the treatment, and precisely timed on the designated chemo day. For patients enrolled in research protocols, the adherence to the defined schedule takes on additional import, since variation is a violation of the protocol. If the oncologist determines that medications must be administered outside the defined constraints, the patient must be un-enrolled from the protocol and the course of therapy is re-written. Pharmacy and eMAR systems utilized in processing chemotherapy medications must be able to support the intricate relationships between each drug defined in the treatment plans. PMID:21347104

Computerized training management system

DOEpatents

Rice, H.B.; McNair, R.C.; White, K.; Maugeri, T.

1998-08-04

A Computerized Training Management System (CTMS) is disclosed for providing a procedurally defined process that is employed to develop accreditable performance based training programs for job classifications that are sensitive to documented regulations and technical information. CTMS is a database that links information needed to maintain a five-phase approach to training-analysis, design, development, implementation, and evaluation independent of training program design. CTMS is designed using R-Base{trademark}, an-SQL compliant software platform. Information is logically entered and linked in CTMS. Each task is linked directly to a performance objective, which, in turn, is linked directly to a learning objective; then, each enabling objective is linked to its respective test items. In addition, tasks, performance objectives, enabling objectives, and test items are linked to their associated reference documents. CTMS keeps all information up to date since it automatically sorts, files and links all data; CTMS includes key word and reference document searches. 18 figs.

Computerized training management system

DOEpatents

Rice, Harold B.; McNair, Robert C.; White, Kenneth; Maugeri, Terry

1998-08-04

A Computerized Training Management System (CTMS) for providing a procedurally defined process that is employed to develop accreditable performance based training programs for job classifications that are sensitive to documented regulations and technical information. CTMS is a database that links information needed to maintain a five-phase approach to training-analysis, design, development, implementation, and evaluation independent of training program design. CTMS is designed using R-Base.RTM., an-SQL compliant software platform. Information is logically entered and linked in CTMS. Each task is linked directly to a performance objective, which, in turn, is linked directly to a learning objective; then, each enabling objective is linked to its respective test items. In addition, tasks, performance objectives, enabling objectives, and test items are linked to their associated reference documents. CTMS keeps all information up to date since it automatically sorts, files and links all data; CTMS includes key word and reference document searches.

Axially staged combustion system for a gas turbine engine

DOEpatents

Bland, Robert J [Oviedo, FL

2009-12-15

An axially staged combustion system is provided for a gas turbine engine comprising a main body structure having a plurality of first and second injectors. First structure provides fuel to at least one of the first injectors. The fuel provided to the one first injector is adapted to mix with air and ignite to produce a flame such that the flame associated with the one first injector defines a flame front having an average length when measured from a reference surface of the main body structure. Each of the second injectors comprising a section extending from the reference surface of the main body structure through the flame front and having a length greater than the average length of the flame front. Second structure provides fuel to at least one of the second injectors. The fuel passes through the one second injector and exits the one second injector at a location axially spaced from the flame front.

Position feedback system for volume holographic storage media

DOEpatents

Hays, Nathan J [San Francisco, CA; Henson, James A [Morgan Hill, CA; Carpenter, Christopher M [Sunnyvale, CA; Akin, Jr William R. [Morgan Hill, CA; Ehrlich, Richard M [Saratoga, CA; Beazley, Lance D [San Jose, CA

1998-07-07

A method of holographic recording in a photorefractive medium wherein stored holograms may be retrieved with maximum signal-to noise ratio (SNR) is disclosed. A plurality of servo blocks containing position feedback information is recorded in the crystal and made non-erasable by heating the crystal. The servo blocks are recorded at specific increments, either angular or frequency, depending whether wavelength or angular multiplexing is applied, and each servo block is defined by one of five patterns. Data pages are then recorded at positions or wavelengths enabling each data page to be subsequently reconstructed with servo patterns which provide position feedback information. The method of recording data pages and servo blocks is consistent with conventional practices. In addition, the recording system also includes components (e.g. voice coil motor) which respond to position feedback information and adjust the angular position of the reference angle of a reference beam to maximize SNR by reducing crosstalk, thereby improving storage capacity.

Inclusion of thin target and source regions in alimentary and respiratory tract systems of mesh-type ICRP adult reference phantoms

NASA Astrophysics Data System (ADS)

Kim, Han Sung; Yeom, Yeon Soo; Tat Nguyen, Thang; Choi, Chansoo; Han, Min Cheol; Lee, Jai Ki; Kim, Chan Hyeong; Zankl, Maria; Petoussi-Henss, Nina; Bolch, Wesley E.; Lee, Choonsik; Qiu, Rui; Eckerman, Keith; Chung, Beom Sun

2017-03-01

It is not feasible to define very small or complex organs and tissues in the current voxel-type adult reference computational phantoms of the International Commission on Radiological Protection (ICRP), which limit dose coefficients for weakly penetrating radiations. To address the problem, the ICRP is converting the voxel-type reference phantoms into mesh-type phantoms. In the present study, as a part of the conversion project, the micrometer-thick target and source regions in the alimentary and respiratory tract systems as described in ICRP Publications 100 and 66 were included in the mesh-type ICRP reference adult male and female phantoms. In addition, realistic lung airway models were simulated to represent the bronchial (BB) and bronchiolar (bb) regions. The electron specific absorbed fraction (SAF) values for the alimentary and respiratory tract systems were then calculated and compared with the values calculated with the stylized models of ICRP Publications 100 and 66. The comparisons show generally good agreement for the oral cavity, oesophagus, and BB, whereas for the stomach, small intestine, large intestine, extrathoracic region, and bb, there are some differences (e.g. up to ~9 times in the large intestine). The difference is mainly due to anatomical difference in these organs between the realistic mesh-type phantoms and the simplified stylized models. The new alimentary and respiratory tract models in the mesh-type ICRP reference phantoms preserve the topology and dimensions of the voxel-type ICRP phantoms and provide more reliable SAF values than the simplified models adopted in previous ICRP Publications.

Device for monitoring cell voltage

DOEpatents

Doepke, Matthias [Garbsen, DE; Eisermann, Henning [Edermissen, DE

2012-08-21

A device for monitoring a rechargeable battery having a number of electrically connected cells includes at least one current interruption switch for interrupting current flowing through at least one associated cell and a plurality of monitoring units for detecting cell voltage. Each monitoring unit is associated with a single cell and includes a reference voltage unit for producing a defined reference threshold voltage and a voltage comparison unit for comparing the reference threshold voltage with a partial cell voltage of the associated cell. The reference voltage unit is electrically supplied from the cell voltage of the associated cell. The voltage comparison unit is coupled to the at least one current interruption switch for interrupting the current of at least the current flowing through the associated cell, with a defined minimum difference between the reference threshold voltage and the partial cell voltage.

[Pediatric reference intervals : retrospective study on thyroid hormone levels].

PubMed

Ladang, A; Vranken, L; Luyckx, F; Lebrethon, M-C; Cavalier, E

2017-01-01

Defining reference range is an essential tool for diagnostic. Age and sexe influences on thyroid hormone levels have been already discussed. In this study, we are defining a new pediatric reference range for TSH, FT3 and FT4 for Cobas C6000 analyzer. To do so, we have taken in account 0 to 18 year old outclinic patients. During the first year of life, thyroid hormone levels change dramatically before getting stabilized around 3 years old. We also compared our results to those obtained in a Canadian large-scale prospective study (the CALIPER initiative).

A study of the application of differential techniques to the global positioning system for a helicopter precision approach

NASA Technical Reports Server (NTRS)

Mccall, D. L.

1984-01-01

The results of a simulation study to define the functional characteristics of a airborne and ground reference GPS receiver for use in a Differential GPS system are doumented. The operations of a variety of receiver types (sequential-single channel, continuous multi-channel, etc.) are evaluated for a typical civil helicopter mission scenario. The math model of each receiver type incorporated representative system errors including intentional degradation. The results include the discussion of the receiver relative performance, the spatial correlative properties of individual range error sources, and the navigation algorithm used to smooth the position data.

Applying Workspace Limitations in a Velocity-Controlled Robotic Mechanism

NASA Technical Reports Server (NTRS)

Abdallah, Muhammad E. (Inventor); Hargrave, Brian (Inventor); Platt, Robert J., Jr. (Inventor)

2014-01-01

A robotic system includes a robotic mechanism responsive to velocity control signals, and a permissible workspace defined by a convex-polygon boundary. A host machine determines a position of a reference point on the mechanism with respect to the boundary, and includes an algorithm for enforcing the boundary by automatically shaping the velocity control signals as a function of the position, thereby providing smooth and unperturbed operation of the mechanism along the edges and corners of the boundary. The algorithm is suited for application with higher speeds and/or external forces. A host machine includes an algorithm for enforcing the boundary by shaping the velocity control signals as a function of the reference point position, and a hardware module for executing the algorithm. A method for enforcing the convex-polygon boundary is also provided that shapes a velocity control signal via a host machine as a function of the reference point position.

Cheap but accurate calculation of chemical reaction rate constants from ab initio data, via system-specific, black-box force fields

NASA Astrophysics Data System (ADS)

Steffen, Julien; Hartke, Bernd

2017-10-01

Building on the recently published quantum-mechanically derived force field (QMDFF) and its empirical valence bond extension, EVB-QMDFF, it is now possible to generate a reliable potential energy surface for any given elementary reaction step in an essentially black box manner. This requires a limited and pre-defined set of reference data near the reaction path and generates an accurate approximation of the reference potential energy surface, on and off the reaction path. This intermediate representation can be used to generate reaction rate data, with far better accuracy and reliability than with traditional approaches based on transition state theory (TST) or variational extensions thereof (VTST), even if those include sophisticated tunneling corrections. However, the additional expense at the reference level remains very modest. We demonstrate all this for three arbitrarily chosen example reactions.

Event-Driven Process Chains (EPC)

NASA Astrophysics Data System (ADS)

Mendling, Jan

This chapter provides a comprehensive overview of Event-driven Process Chains (EPCs) and introduces a novel definition of EPC semantics. EPCs became popular in the 1990s as a conceptual business process modeling language in the context of reference modeling. Reference modeling refers to the documentation of generic business operations in a model such as service processes in the telecommunications sector, for example. It is claimed that reference models can be reused and adapted as best-practice recommendations in individual companies (see [230, 168, 229, 131, 400, 401, 446, 127, 362, 126]). The roots of reference modeling can be traced back to the Kölner Integrationsmodell (KIM) [146, 147] that was developed in the 1960s and 1970s. In the 1990s, the Institute of Information Systems (IWi) in Saarbrücken worked on a project with SAP to define a suitable business process modeling language to document the processes of the SAP R/3 enterprise resource planning system. There were two results from this joint effort: the definition of EPCs [210] and the documentation of the SAP system in the SAP Reference Model (see [92, 211]). The extensive database of this reference model contains almost 10,000 sub-models: 604 of them non-trivial EPC business process models. The SAP Reference model had a huge impact with several researchers referring to it in their publications (see [473, 235, 127, 362, 281, 427, 415]) as well as motivating the creation of EPC reference models in further domains including computer integrated manufacturing [377, 379], logistics [229] or retail [52]. The wide-spread application of EPCs in business process modeling theory and practice is supported by their coverage in seminal text books for business process management and information systems in general (see [378, 380, 49, 384, 167, 240]). EPCs are frequently used in practice due to a high user acceptance [376] and extensive tool support. Some examples of tools that support EPCs are ARIS Toolset by IDS Scheer AG, AENEIS by ATOSS Software AG, ADONIS by BOC GmbH, Visio by Microsoft Corp., Nautilus by Gedilan Consulting GmbH, and Bonapart by Pikos GmbH. In order to facilitate the interchange of EPC business process models between these tools, there is a tool neutral interchange format called EPC Markup Language (EPML) [283, 285, 286, 287, 289, 290, 291].

larvalign: Aligning Gene Expression Patterns from the Larval Brain of Drosophila melanogaster.

PubMed

Muenzing, Sascha E A; Strauch, Martin; Truman, James W; Bühler, Katja; Thum, Andreas S; Merhof, Dorit

2018-01-01

The larval brain of the fruit fly Drosophila melanogaster is a small, tractable model system for neuroscience. Genes for fluorescent marker proteins can be expressed in defined, spatially restricted neuron populations. Here, we introduce the methods for 1) generating a standard template of the larval central nervous system (CNS), 2) spatial mapping of expression patterns from different larvae into a reference space defined by the standard template. We provide a manually annotated gold standard that serves for evaluation of the registration framework involved in template generation and mapping. A method for registration quality assessment enables the automatic detection of registration errors, and a semi-automatic registration method allows one to correct registrations, which is a prerequisite for a high-quality, curated database of expression patterns. All computational methods are available within the larvalign software package: https://github.com/larvalign/larvalign/releases/tag/v1.0.

The Ablowitz–Ladik system on a finite set of integers

NASA Astrophysics Data System (ADS)

Xia, Baoqiang

2018-07-01

We show how to solve initial-boundary value problems for integrable nonlinear differential–difference equations on a finite set of integers. The method we employ is the discrete analogue of the unified transform (Fokas method). The implementation of this method to the Ablowitz–Ladik system yields the solution in terms of the unique solution of a matrix Riemann–Hilbert problem, which has a jump matrix with explicit -dependence involving certain functions referred to as spectral functions. Some of these functions are defined in terms of the initial value, while the remaining spectral functions are defined in terms of two sets of boundary values. These spectral functions are not independent but satisfy an algebraic relation called global relation. We analyze the global relation to characterize the unknown boundary values in terms of the given initial and boundary values. We also discuss the linearizable boundary conditions.

Foveal Machine Vision Systems

DTIC Science & Technology

1990-08-01

12 The smallest regions defined by the superposition of the rexel boundaries of all the frames will be referred to as unisource regions. 85I I Chapter... unisource region are identical. I The advantage of rexel formatted data is its small size. However, the storage of rexel data in a uniform two...dimensional array is difficult because unisource regions can take on a wide variety of shapes. Rexel data can be stored in thinned uniform arrays, but this

A Wave Theory for Non-Imaging Concentrators

DTIC Science & Technology

1992-04-01

the radiance function over the z = 0 plane, as defined by Walther (W), 6 W. T. Welford and R. Winston , High Collection Nonimaging Optics , Academic...Laurel, Maryland 2072&-6099 REFERENCES IW. T. Welford and R. Winston , High Collection Nonimaging Optics , Academic Press, New York (1989). 2 W. Welford and...radiance function is invariant for a large class of optical systems. It is also shown that fundamental limitations for the concentration of light follow

Modelling Team Adversarial Actions in UAV Operations

DTIC Science & Technology

2007-11-01

support for the dynamic creation and destruction of entities is the history dependent automata ( HDA ) [9] which evolved from an algorithmic structure for...checking bi-similarity of π- calculus agents. The authors define HDA as automata which perform actions that can carry information generated in the...past history of the system. The states, transitions and labels of the HDA are enriched with sets of local names. Thus, each transition can refer to the

Warranty Guidebook: A Reference for Use by DoD Managers in Developing, Applying and Administering Warranties

DTIC Science & Technology

1992-10-01

germane and perplexing questions persist: "* How should complex weapon system essential performance characteristics be warranted? "" What should a...conditions be developed? "• Who will administer the warranty and how? "* Under what conditions are such warranties inappropriate? The Department of...warranties define what is to be warranted, the warranty duration, accertable conditions, and the supplier’s liability. However, program managers should not

A geographic information system-based method for estimating cancer rates in non-census defined geographical areas.

PubMed

Freeman, Vincent L; Boylan, Emma E; Pugach, Oksana; Mclafferty, Sara L; Tossas-Milligan, Katherine Y; Watson, Karriem S; Winn, Robert A

2017-10-01

To address locally relevant cancer-related health issues, health departments frequently need data beyond that contained in standard census area-based statistics. We describe a geographic information system-based method for calculating age-standardized cancer incidence rates in non-census defined geographical areas using publically available data. Aggregated records of cancer cases diagnosed from 2009 through 2013 in each of Chicago's 77 census-defined community areas were obtained from the Illinois State Cancer Registry. Areal interpolation through dasymetric mapping of census blocks was used to redistribute populations and case counts from community areas to Chicago's 50 politically defined aldermanic wards, and ward-level age-standardized 5-year cumulative incidence rates were calculated. Potential errors in redistributing populations between geographies were limited to <1.5% of the total population, and agreement between our ward population estimates and those from a frequently cited reference set of estimates was high (Pearson correlation r = 0.99, mean difference = -4 persons). A map overlay of safety-net primary care clinic locations and ward-level incidence rates for advanced-staged cancers revealed potential pathways for prevention. Areal interpolation through dasymetric mapping can estimate cancer rates in non-census defined geographies. This can address gaps in local cancer-related health data, inform health resource advocacy, and guide community-centered cancer prevention and control.

On the use of regression analysis for the estimation of human biological age.

PubMed

Krøll, J; Saxtrup, O

2000-01-01

The present investigation compares three linear regression procedures for the definition of human biological age (bioage). As a model system for bioage definition is used the variations with age of blood hemoglobin (B-hemoglobin) in males in the age range 50-95 years. The bioage measures compared are: 1: P-bioage; defined from regression of chronological age on B-hemoglobin results. 2: AC-bioage; obtained by indirect regression, using in reverse the equation describing the regression of B-hemoglobin on age in a reference population. 3: BC-bioage; defined by orthogonal regression on the reference regression line of B-hemoglobin on age. It is demonstrated that the P-bioage measure gives an overestimation of the bioage in the younger and an underestimation in the older individuals. This 'regression to the mean' is avoided using the indirect regression procedures. Here the relatively low SD of the BC-bioage measure results from the inclusion of individual chronological age in the orthogonal regression procedure. Observations on male blood donors illustrates the variation of the AC- and BC-bioage measures in the individual.

Development and Characterization of a Low-Pressure Calibration System for Hypersonic Wind Tunnels

NASA Technical Reports Server (NTRS)

Green, Del L.; Everhart, Joel L.; Rhode, Matthew N.

2004-01-01

Minimization of uncertainty is essential for accurate ESP measurements at very low free-stream static pressures found in hypersonic wind tunnels. Statistical characterization of environmental error sources requires a well defined and controlled calibration method. A calibration system has been constructed and environmental control software developed to control experimentation to eliminate human induced error sources. The initial stability study of the calibration system shows a high degree of measurement accuracy and precision in temperature and pressure control. Control manometer drift and reference pressure instabilities induce uncertainty into the repeatability of voltage responses measured from the PSI System 8400 between calibrations. Methods of improving repeatability are possible through software programming and further experimentation.

Hybrid shearing and phase-shifting point diffraction interferometer

DOEpatents

Goldberg, Kenneth Alan; Naulleau, Patrick P.

2003-06-03

A new interferometry configuration combines the strengths of two existing interferometry methods, improving the quality and extending the dynamic range of both. On the same patterned mask, placed near the image-plane of an optical system under test, patterns for phase-shifting point diffraction interferometry and lateral shearing interferometry coexist. The former giving verifiable high accuracy for the measurement of nearly diffraction-limited optical systems. The latter enabling the measurement of optical systems with more than one wave of aberration in the system wavefront. The interferometry configuration is a hybrid shearing and point diffraction interferometer system for testing an optical element that is positioned along an optical path including: a source of electromagnetic energy in the optical path; a first beam splitter that is secured to a device that includes means for maneuvering the first beam splitter in a first position wherein the first beam splitter is in the optical path dividing light from the source into a reference beam and a test beam and in a second position wherein the first beam splitter is outside the optical path: a hybrid mask which includes a first section that defines a test window and at least one reference pinhole and a second section that defines a second beam splitter wherein the hybrid mask is secured to a device that includes means for maneuvering either the first section or the second section into the optical path positioned in an image plane that is created by the optical element, with the proviso that the first section of the hybrid mask is positioned in the optical path when first beam splitter is positioned in the optical path; and a detector positioned after the hybrid mask along the optical path.

Relations between water physico-chemistry and benthic algal communities in a northern Canadian watershed: defining reference conditions using multiple descriptors of community structure.

PubMed

Thomas, Kathryn E; Hall, Roland I; Scrimgeour, Garry J

2015-09-01

Defining reference conditions is central to identifying environmental effects of anthropogenic activities. Using a watershed approach, we quantified reference conditions for benthic algal communities and their relations to physico-chemical conditions in rivers in the South Nahanni River watershed, NWT, Canada, in 2008 and 2009. We also compared the ability of three descriptors that vary in terms of analytical costs to define algal community structure based on relative abundances of (i) all algal taxa, (ii) only diatom taxa, and (iii) photosynthetic pigments. Ordination analyses showed that variance in algal community structure was strongly related to gradients in environmental variables describing water physico-chemistry, stream habitats, and sub-watershed structure. Water physico-chemistry and local watershed-scale descriptors differed significantly between algal communities from sites in the Selwyn Mountain ecoregion compared to sites in the Nahanni-Hyland ecoregions. Distinct differences in algal community types between ecoregions were apparent irrespective of whether algal community structure was defined using all algal taxa, diatom taxa, or photosynthetic pigments. Two algal community types were highly predictable using environmental variables, a core consideration in the development of Reference Condition Approach (RCA) models. These results suggest that assessments of environmental impacts could be completed using RCA models for each ecoregion. We suggest that use of algal pigments, a high through-put analysis, is a promising alternative compared to more labor-intensive and costly taxonomic approaches for defining algal community structure.

Pulsar Timing and Its Application for Navigation and Gravitational Wave Detection

NASA Astrophysics Data System (ADS)

Becker, Werner; Kramer, Michael; Sesana, Alberto

2018-02-01

Pulsars are natural cosmic clocks. On long timescales they rival the precision of terrestrial atomic clocks. Using a technique called pulsar timing, the exact measurement of pulse arrival times allows a number of applications, ranging from testing theories of gravity to detecting gravitational waves. Also an external reference system suitable for autonomous space navigation can be defined by pulsars, using them as natural navigation beacons, not unlike the use of GPS satellites for navigation on Earth. By comparing pulse arrival times measured on-board a spacecraft with predicted pulse arrivals at a reference location (e.g. the solar system barycenter), the spacecraft position can be determined autonomously and with high accuracy everywhere in the solar system and beyond. We describe the unique properties of pulsars that suggest that such a navigation system will certainly have its application in future astronautics. We also describe the on-going experiments to use the clock-like nature of pulsars to "construct" a galactic-sized gravitational wave detector for low-frequency (f_{GW}˜ 10^{-9} - 10^{-7} Hz) gravitational waves. We present the current status and provide an outlook for the future.

Competition Between Transients in the Rate of Approach to a Fixed Point

NASA Astrophysics Data System (ADS)

Day, Judy; Rubin, Jonathan E.; Chow, Carson C.

2009-01-01

The goal of this paper is to provide and apply tools for analyzing a specific aspect of transient dynamics not covered by previous theory. The question we address is whether one component of a perturbed solution to a system of differential equations can overtake the corresponding component of a reference solution as both converge to a stable node at the origin, given that the perturbed solution was initially farther away and that both solutions are nonnegative for all time. We call this phenomenon tolerance, for its relation to a biological effect. We show using geometric arguments that tolerance will exist in generic linear systems with a complete set of eigenvectors and in excitable nonlinear systems. We also define a notion of inhibition that may constrain the regions in phase space where the possibility of tolerance arises in general systems. However, these general existence theorems do not not yield an assessment of tolerance for specific initial conditions. To address that issue, we develop some analytical tools for determining if particular perturbed and reference solution initial conditions will exhibit tolerance.

Making intelligent systems team players. A guide to developing intelligent monitoring systems

NASA Technical Reports Server (NTRS)

Land, Sherry A.; Malin, Jane T.; Thronesberry, Carroll; Schreckenghost, Debra L.

1995-01-01

This reference guide for developers of intelligent monitoring systems is based on lessons learned by developers of the DEcision Support SYstem (DESSY), an expert system that monitors Space Shuttle telemetry data in real time. DESSY makes inferences about commands, state transitions, and simple failures. It performs failure detection rather than in-depth failure diagnostics. A listing of rules from DESSY and cue cards from DESSY subsystems are included to give the development community a better understanding of the selected model system. The G-2 programming tool used in developing DESSY provides an object-oriented, rule-based environment, but many of the principles in use here can be applied to any type of monitoring intelligent system. The step-by-step instructions and examples given for each stage of development are in G-2, but can be used with other development tools. This guide first defines the authors' concept of real-time monitoring systems, then tells prospective developers how to determine system requirements, how to build the system through a combined design/development process, and how to solve problems involved in working with real-time data. It explains the relationships among operational prototyping, software evolution, and the user interface. It also explains methods of testing, verification, and validation. It includes suggestions for preparing reference documentation and training users.

4D Dynamic RNP Annual Interim Report-Year 1

NASA Technical Reports Server (NTRS)

Finkelsztein, Daniel M.; Sturdy, James L.; Alaverdi, Omeed; Chung, William W.; Salvano, Daniel; Klooster, Joel; Hochwarth, Joachim K.

2010-01-01

This Annual Interim Report summarizes the activities led by Raytheon, in collaboration with GE Aviation and SAIC, and presents the results obtained during the first year of this research effort to expand the RNP concept to 4 dimensions relative to a dynamic frame of reference. Joint Program Development Office (JPDO)Concepts of Operations for the Next Generation Air Transportation System (NextGen) considers 4 Dimension Trajectory (4DT) procedures a key enabler to Trajectory Based Operations (TBO). The JPDO defines 4DT as a precise description of an aircraft path in space and time . While NextGen assumes that this path is defined within an Earth-reference frame, many 4DT procedure implementations will require an aircraft to precisely navigate relative to a moving reference such as another aircraft to form aggregate flows or a weather cell to allow for flows to shift. Current methods of implementing routes and flight paths rely on aircraft meeting a Required Navigation Performance (RNP) specification and being equipped with a monitoring and alerting capability to annunciate when the aircraft system is unable to meet the performance specification required for the operation. Since all aircraft today operate within the NAS relative to fixed reference points, the current RNP definition is deemed satisfactory. However, it is not well understood how the current RNP construct will support NextGen 4DT procedures where aircraft operate relative to each other or to other dynamic frames of reference. The objective of this research effort is to analyze candidate 4DT procedures from both an Air Navigation Service Provider (ANSP) and aircraft perspective, to identify their specific navigational requirements, assess the shortcomings of the current RNP construct to meet these requirements, to propose an extended 4 Dimensional Dynamic RNP (4D Dynamic RNP) construct that accounts for the dynamic spatial and temporal nature of the selected 4DT procedures, and finally, to design an experiment using the Airspace and Traffic Operations Simulation (ATOS) system to validate the 4D Dynamic RNP construct. This Annual Interim Report summarizes the activities led by Raytheon, in collaboration with GE Aviation and SAIC, and presents the results obtained during the first year of this research effort to expand the RNP concept to 4 dimensions relative to a dynamic frame of reference. A comprehensive assessment of the state-of-the-art international implementation of current RNP was completed and presented in the Contractor Report RNP State-of-the-Art Assessment, Version 4, 17 December 2008 . The team defined in detail two 4DT operations, Airborne Precision Spacing and Self-Separation, that are ideally suited to be supported by 4D Dynamic RNP and developed their respective conceptual frameworks, Required Interval Management Performance (RIMP) Version 1.1, 13 April 2009 and Required Self Separation Performance (RSSP) Version 1.1, 13 April 2009 . Finally, the team started the development of a mathematical model and simulation tool for RIMP and RSSP scheduled to be delivered during the second year of this research effort.

Operable Data Management for Ocean Observing Systems

NASA Astrophysics Data System (ADS)

Chavez, F. P.; Graybeal, J. B.; Godin, M. A.

2004-12-01

As oceanographic observing systems become more numerous and complex, data management solutions must follow. Most existing oceanographic data management systems fall into one of three categories: they have been developed as dedicated solutions, with limited application to other observing systems; they expect that data will be pre-processed into well-defined formats, such as netCDF; or they are conceived as robust, generic data management solutions, with complexity (high) and maturity and adoption rates (low) to match. Each approach has strengths and weaknesses; no approach yet fully addresses, nor takes advantage of, the sophistication of ocean observing systems as they are now conceived. In this presentation we describe critical data management requirements for advanced ocean observing systems, of the type envisioned by ORION and IOOS. By defining common requirements -- functional, qualitative, and programmatic -- for all such ocean observing systems, the performance and nature of the general data management solution can be characterized. Issues such as scalability, maintaining metadata relationships, data access security, visualization, and operational flexibility suggest baseline architectural characteristics, which may in turn lead to reusable components and approaches. Interoperability with other data management systems, with standards-based solutions in metadata specification and data transport protocols, and with the data management infrastructure envisioned by IOOS and ORION, can also be used to define necessary capabilities. Finally, some requirements for the software infrastructure of ocean observing systems can be inferred. Early operational results and lessons learned, from development and operations of MBARI ocean observing systems, are used to illustrate key requirements, choices, and challenges. Reference systems include the Monterey Ocean Observing System (MOOS), its component software systems (Software Infrastructure and Applications for MOOS, and the Shore Side Data System), and the Autonomous Ocean Sampling Network (AOSN).

Fixing a Reference Frame to a Moving and Deforming Continent

NASA Astrophysics Data System (ADS)

Blewitt, G.; Kreemer, C.; Hammond, W. C.

2016-12-01

The U.S. National Spatial Reference System will be modernized in 2022. A foundational component will be a geocentric reference frame fixed to the North America tectonic plate. Here we address challenges of fixing a reference frame to a moving and deforming continent. Scientific applications motivate that we fix the frame with a scale consistent with the SI system, an origin that coincides with the Earth system's center of mass, and with axes attached to the rigidly rotating interior of the North America plate. Realizing the scale and origin is now achieved to < 0.5 mm/yr by combining space-geodetic techniques (SLR, VLBI, GPS, and DORIS) in the global system, ITRS. To realize the no-net rotation condition, the complexity of plate boundary deformation demands that we only select GPS stations far from plate boundaries. Another problem is that velocity uncertainties in models of glacial isostatic adjustment (GIA) are significant compared to uncertainties in observed velocities. GIA models generally agree that far-field horizontal velocities tend to be directed toward/away from Hudson Bay, depending on mantle viscosity, with uncertain sign and magnitude of velocity. Also in the far field, strain rates tend to be small beyond the peripheral bulge ( US-Canada border). Thus the Earth's crust in the US east of the Rockies may appear to be rigid, even if this region moves relative to plate motion. This can affect Euler vector estimation, with implications (pros and cons) on scientific interpretation. Our previous approach [ref. 1] in defining the NA12 frame was to select a core set of 30 stations east of the Rockies and south of the U.S.-Canada border that satisfy strict criteria on position time series quality. The resulting horizontal velocities have an RMS of 0.3 mm/yr, quantifying a combination of plate rigidity and accuracy. However, this does not rule out possible common-mode motion arising from GIA. For the development of new frame NA16, we consider approaches to this problem. We also apply new techniques including the MIDAS robust velocity estimator [ref. 2] and "GPS Imaging" of vertical motions and strain rates (Fig. 1), which together could assist in better defining "stable North America".[1] Blewitt et al. (2013). J. Geodyn. 72, 11-24, doi:10.1016/j.jog.2013.08.004[2] Blewitt et al. (2016). JGR 121, doi:10.1002/2015JB012552

Instantaneous progression reference frame for calculating pelvis rotations: Reliable and anatomically-meaningful results independent of the direction of movement.

PubMed

Kainz, Hans; Lloyd, David G; Walsh, Henry P J; Carty, Christopher P

2016-05-01

In motion analysis, pelvis angles are conventionally calculated as the rotations between the pelvis and laboratory reference frame. This approach assumes that the participant's motion is along the anterior-posterior laboratory reference frame axis. When this assumption is violated interpretation of pelvis angels become problematic. In this paper a new approach for calculating pelvis angles based on the rotations between the pelvis and an instantaneous progression reference frame was introduced. At every time-point, the tangent to the trajectory of the midpoint of the pelvis projected into the horizontal plane of the laboratory reference frame was used to define the anterior-posterior axis of the instantaneous progression reference frame. This new approach combined with the rotation-obliquity-tilt rotation sequence was compared to the conventional approach using the rotation-obliquity-tilt and tilt-obliquity-rotation sequences. Four different movement tasks performed by eight healthy adults were analysed. The instantaneous progression reference frame approach was the only approach that showed reliable and anatomically meaningful results for all analysed movement tasks (mean root-mean-square-differences below 5°, differences in pelvis angles at pre-defined gait events below 10°). Both rotation sequences combined with the conventional approach led to unreliable results as soon as the participant's motion was not along the anterior-posterior laboratory axis (mean root-mean-square-differences up to 30°, differences in pelvis angles at pre-defined gait events up to 45°). The instantaneous progression reference frame approach enables the gait analysis community to analysis pelvis angles for movements that do not follow the anterior-posterior axis of the laboratory reference frame. Copyright © 2016 Elsevier B.V. All rights reserved.

Autonomously acquiring declarative and procedural knowledge for ICAT systems

NASA Technical Reports Server (NTRS)

Kovarik, Vincent J., Jr.

1993-01-01

The construction of Intelligent Computer Aided Training (ICAT) systems is critically dependent on the ability to define and encode knowledge. This knowledge engineering effort can be broadly divided into two categories: domain knowledge and expert or task knowledge. Domain knowledge refers to the physical environment or system with which the expert interacts. Expert knowledge consists of the set of procedures and heuristics employed by the expert in performing their task. Both these areas are a significant bottleneck in the acquisition of knowledge for ICAT systems. This paper presents a research project in the area of autonomous knowledge acquisition using a passive observation concept. The system observes an expert and then generalizes the observations into production rules representing the domain expert's knowledge.

Design and Principles Enabling the Space Reference FOM

NASA Technical Reports Server (NTRS)

Moeller, Bjoern; Dexter, Dan; Madden, Michael; Crues, Edwin Z.; Garro, Alfredo; Skuratovskiy, Anton

2017-01-01

A first complete draft of the Simulation Interoperability Standards Organization (SISO) Space Reference Federation Object Model (FOM) has now been produced. This paper provides some insights into its capabilities and discusses the opportunity for reuse in other domains. The focus of this first version of the standard is execution control, time management and coordinate systems, well-known reference frames, as well as some basic support for physical entities. The biggest part of the execution control is the coordinated start-up process. This process contains a number of steps, including checking of required federates, handling of early versus late joiners, sharing of federation wide configuration data and multi-phase initialization. An additional part of Execution Control is the coordinated and synchronized transition between Run mode, Freeze mode and Shutdown. For time management, several time lines are defined, including real-time, scenario time, High Level Architecture (HLA) logical time and physical time. A strategy for mixing simulations that use different time steps is introduced, as well as an approach for finding common boundaries for fully synchronized freeze. For describing spatial information, a mechanism with a set of reference frames is specified. Each reference frame has a position and orientation related to a parent reference frame. This makes it possible for federates to perform calculations in reference frames that are convenient to them. An operation on the Moon can be performed using lunar coordinates whereas an operation on Earth can be performed using Earth coordinates. At the same time, coordinates in one reference frame have an unambiguous relationship to a coordinate in another reference frame. While the Space Reference FOM is originally being developed for Space operations, the authors believe that many parts of it can be reused for any simulation that has a focus on physical processes with one or more coordinate systems, and require high fidelity and repeatability.

The (Un)Lonely Planet Guide: Formation and Evolution of Planetary Systems from a ``Blue Dots'' Perspective

NASA Astrophysics Data System (ADS)

Meyer, M. R.

2010-10-01

In this contribution I summarize some recent successes, and focus on remaining challenges, in understanding the formation and evolution of planetary systems in the context of the Blue Dots initiative. Because our understanding is incomplete, we cannot yet articulate a design reference mission engineering matrix suitable for an exploration mission where success is defined as obtaining a spectrum of a potentially habitable world around a nearby star. However, as progress accelerates, we can identify observational programs that would address fundamental scientific questions through hypothesis testing such that the null result is interesting.

[Development of an optimal scheme for calculating results of the use of an immunoenzyme test-system for determining the antigenic activity of a cultured antirabies vaccine].

PubMed

Tsetlin, E M; Volkova, R A

1996-01-01

Ninety-eight lots of commercial antirabies vaccine manufactured by Immunopreparat Research and Production Amalgamation have been tested using enzyme immunoassay system for the detection of rabies virus antigens. Comparison of different variants of interpreting and expressing the results helped define the optimal method for assessment of vaccine titer and reference values: optical density value equal to 0.2 is taken as the cut-off. Antigenic activity of the vaccine may be expressed in international units, similarly as immunogenic activity.

A Modernized National Spatial Reference System in 2022: Focus on the Caribbean Terrestrial Reference Frame

NASA Astrophysics Data System (ADS)

Roman, D. R.

2017-12-01

In 2022, the National Geodetic Survey will replace all three NAD 83 reference frames the four new terrestrial reference frames. Each frame will be named after a tectonic plate (North American, Pacific, Caribbean and Mariana) and each will be related to the IGS frame through three Euler Pole parameters (EPPs). This talk will focus on practical application in the Caribbean region. A working group is being re-established for development of the North American region and will likely also result in analysis of the Pacific region as well. Both of these regions are adequately covered with existing CORS sites to model the EPPs. The Mariana region currently lacks sufficient coverage, but a separate project is underway to collect additional information to help in defining EPPs for that region at a later date. The Caribbean region has existing robust coverage through UNAVCO's COCONet and other data sets, but these require further analysis. This discussion will focus on practical examination of Caribbean sites to establish candidates for determining the Caribbean frame EPPs as well as an examination of any remaining velocities that might inform a model of the remaining velocities within that frame (Intra-Frame Velocity Model). NGS has a vested interest in defining such a model to meet obligations to U.S. citizens in Puerto Rico and the U.S. Virgin Islands. Beyond this, NGS aims to collaborate with other countries in the region through efforts with SIRGAS and UN-GGIM-Americas for a more acceptable regional model to serve everyone's needs.

Gravity Influences the Visual Representation of Object Tilt in Parietal Cortex

PubMed Central

Angelaki, Dora E.

2014-01-01

Sensory systems encode the environment in egocentric (e.g., eye, head, or body) reference frames, creating inherently unstable representations that shift and rotate as we move. However, it is widely speculated that the brain transforms these signals into an allocentric, gravity-centered representation of the world that is stable and independent of the observer's spatial pose. Where and how this representation may be achieved is currently unknown. Here we demonstrate that a subpopulation of neurons in the macaque caudal intraparietal area (CIP) visually encodes object tilt in nonegocentric coordinates defined relative to the gravitational vector. Neuronal responses to the tilt of a visually presented planar surface were measured with the monkey in different spatial orientations (upright and rolled left/right ear down) and then compared. This revealed a continuum of representations in which planar tilt was encoded in a gravity-centered reference frame in approximately one-tenth of the comparisons, intermediate reference frames ranging between gravity-centered and egocentric in approximately two-tenths of the comparisons, and in an egocentric reference frame in less than half of the comparisons. Altogether, almost half of the comparisons revealed a shift in the preferred tilt and/or a gain change consistent with encoding object orientation in nonegocentric coordinates. Through neural network modeling, we further show that a purely gravity-centered representation of object tilt can be achieved directly from the population activity of CIP-like units. These results suggest that area CIP may play a key role in creating a stable, allocentric representation of the environment defined relative to an “earth-vertical” direction. PMID:25339732

Technostress and the Reference Librarian.

ERIC Educational Resources Information Center

Kupersmith, John

1992-01-01

Defines "technostress" as the stress experienced by reference librarians who must constantly deal with the demands of new information technology and the changes they produce in the work place. Discussion includes suggested ways in which both organizations and individuals can work to reduce stress. (27 references) (LAE)

Changing Roles for References Librarians.

ERIC Educational Resources Information Center

Kelly, Julia; Robbins, Kathryn

1996-01-01

Discusses the future outlook for reference librarians, with topics including: "Technology as the Source of Change"; "Impact of the Internet"; "Defining the Virtual Library"; "Rethinking Reference"; "Out of the Library and into the Streets"; "Asking Users About Their Needs"; "Standardization and Artificial Intelligence"; "The Financial Future"; and…

Long-Term Variations of the EOP and ICRF2

NASA Technical Reports Server (NTRS)

Zharov, Vladimir; Sazhin, Mikhail; Sementsov, Valerian; Sazhina, Olga

2010-01-01

We analyzed the time series of the coordinates of the ICRF radio sources. We show that part of the radio sources, including the defining sources, shows a significant apparent motion. The stability of the celestial reference frame is provided by a no-net-rotation condition applied to the defining sources. In our case this condition leads to a rotation of the frame axes with time. We calculated the effect of this rotation on the Earth orientation parameters (EOP). In order to improve the stability of the celestial reference frame we suggest a new method for the selection of the defining sources. The method consists of two criteria: the first one we call cosmological and the second one kinematical. It is shown that a subset of the ICRF sources selected according to cosmological criteria provides the most stable reference frame for the next decade.

Mars rover/sample return mission requirements affecting space station

NASA Technical Reports Server (NTRS)

1988-01-01

The possible interfaces between the Space Station and the Mars Rover/Sample Return (MRSR) mission are defined. In order to constrain the scope of the report a series of seven design reference missions divided into three major types were assumed. These missions were defined to span the probable range of Space Station-MRSR interactions. The options were reduced, the MRSR sample handling requirements and baseline assumptions about the MRSR hardware and the key design features and requirements of the Space Station are summarized. Only the aspects of the design reference missions necessary to define the interfaces, hooks and scars, and other provisions on the Space Station are considered. An analysis of each of the three major design reference missions, is reported, presenting conceptual designs of key hardware to be mounted on the Space Station, a definition of weights, interfaces, and required hooks and scars.

Thermocouple, multiple junction reference oven

NASA Technical Reports Server (NTRS)

Leblanc, L. P. (Inventor)

1981-01-01

An improved oven for maintaining the junctions of a plurality of reference thermocouples at a common and constant temperature is described. The oven is characterized by a cylindrical body defining a heat sink with axially extended-cylindrical cavity a singularized heating element which comprises a unitary cylindrical heating element consisting of a resistance heating coil wound about the surface of metallic spool with an axial bore defined and seated in the cavity. Other features of the oven include an annular array of radially extended bores defined in the cylindrical body and a plurality of reference thermocouple junctions seated in the bores in uniformly spaced relation with the heating element, and a temperature sensing device seated in the axial bore for detecting temperature changes as they occur in the spool and circuit to apply a voltage across the coil in response to detected drops in temperatures of the spool.

Life sciences space station planning document: A reference payload for the exobiology research facilities

NASA Technical Reports Server (NTRS)

1987-01-01

The Cosmic Dust Collection and Gas Grain Simulation Facilities represent collaborative efforts between the Life Sciences and Solar System Exploration Divisions designed to strengthen a natural exobiology/Planetary Sciences connection. The Cosmic Dust Collection Facility is a Planetary Science facility, with Exobiology a primary user. Conversely, the Gas Grain Facility is an exobiology facility, with Planetary Science a primary user. Requirements for the construction and operation of the two facilities, contained herein, were developed through joint workshops between the two disciplines, as were representative experiments comprising the reference payloads. In the case of the Gas Grain Simulation Facility, the astrophysics Division is an additional potential user, having participated in the workshop to select experiments and define requirements.

Computing the Free Energy along a Reaction Coordinate Using Rigid Body Dynamics.

PubMed

Tao, Peng; Sodt, Alexander J; Shao, Yihan; König, Gerhard; Brooks, Bernard R

2014-10-14

The calculations of potential of mean force along complex chemical reactions or rare events pathways are of great interest because of their importance for many areas in chemistry, molecular biology, and material science. The major difficulty for free energy calculations comes from the great computational cost for adequate sampling of the system in high-energy regions, especially close to the reaction transition state. Here, we present a method, called FEG-RBD, in which the free energy gradients were obtained from rigid body dynamics simulations. Then the free energy gradients were integrated along a reference reaction pathway to calculate free energy profiles. In a given system, the reaction coordinates defining a subset of atoms (e.g., a solute, or the quantum mechanics (QM) region of a quantum mechanics/molecular mechanics simulation) are selected to form a rigid body during the simulation. The first-order derivatives (gradients) of the free energy with respect to the reaction coordinates are obtained through the integration of constraint forces within the rigid body. Each structure along the reference reaction path is separately subjected to such a rigid body simulation. The individual free energy gradients are integrated along the reference pathway to obtain the free energy profile. Test cases provided demonstrate both the strengths and weaknesses of the FEG-RBD method. The most significant benefit of this method comes from the fast convergence rate of the free energy gradient using rigid-body constraints instead of restraints. A correction to the free energy due to approximate relaxation of the rigid-body constraint is estimated and discussed. A comparison with umbrella sampling using a simple test case revealed the improved sampling efficiency of FEG-RBD by a factor of 4 on average. The enhanced efficiency makes this method effective for calculating the free energy of complex chemical reactions when the reaction coordinate can be unambiguously defined by a small subset of atoms within the system.

Computing the Free Energy along a Reaction Coordinate Using Rigid Body Dynamics

PubMed Central

2015-01-01

The calculations of potential of mean force along complex chemical reactions or rare events pathways are of great interest because of their importance for many areas in chemistry, molecular biology, and material science. The major difficulty for free energy calculations comes from the great computational cost for adequate sampling of the system in high-energy regions, especially close to the reaction transition state. Here, we present a method, called FEG-RBD, in which the free energy gradients were obtained from rigid body dynamics simulations. Then the free energy gradients were integrated along a reference reaction pathway to calculate free energy profiles. In a given system, the reaction coordinates defining a subset of atoms (e.g., a solute, or the quantum mechanics (QM) region of a quantum mechanics/molecular mechanics simulation) are selected to form a rigid body during the simulation. The first-order derivatives (gradients) of the free energy with respect to the reaction coordinates are obtained through the integration of constraint forces within the rigid body. Each structure along the reference reaction path is separately subjected to such a rigid body simulation. The individual free energy gradients are integrated along the reference pathway to obtain the free energy profile. Test cases provided demonstrate both the strengths and weaknesses of the FEG-RBD method. The most significant benefit of this method comes from the fast convergence rate of the free energy gradient using rigid-body constraints instead of restraints. A correction to the free energy due to approximate relaxation of the rigid-body constraint is estimated and discussed. A comparison with umbrella sampling using a simple test case revealed the improved sampling efficiency of FEG-RBD by a factor of 4 on average. The enhanced efficiency makes this method effective for calculating the free energy of complex chemical reactions when the reaction coordinate can be unambiguously defined by a small subset of atoms within the system. PMID:25328492

Diagnosis of different liver fibrosis characteristics by blood tests in non-alcoholic fatty liver disease.

PubMed

Calès, Paul; Boursier, Jérôme; Chaigneau, Julien; Lainé, Fabrice; Sandrini, Jeremy; Michalak, Sophie; Hubert, Isabelle; Dib, Nina; Oberti, Frédéric; Bertrais, Sandrine; Hunault, Gilles; Cavaro-Ménard, Christine; Gallois, Yves; Deugnier, Yves; Rousselet, Marie C

2010-10-01

Our aim was to develop an accurate, non-invasive, blood-test-based method for identifying the main characteristics of liver fibrosis in non-alcoholic fatty liver disease (NAFLD). Fibrosis was staged according to NASH-CRN and Metavir systems in 226 patients with NAFLD. A fully automated algorithm measured the fractal dimension (FD) and the area of fibrosis (AOF). Independent predictors of diagnostic targets were determined using bootstrap methods. (i) Development. Significant fibrosis defined by NASH-CRN F ≥2 was diagnosed by weight, glycaemia, aspartate aminotransferase (AST), alanine aminotransferase (ALT) and prothrombin index [area under the receiver operating characteristic (AUROC)=0.867]; significant fibrosis defined by Metavir F ≥2 was diagnosed by weight, age, glycaemia, AST, ALT, ferritin and platelets (FibroMeter AUROC=0.941, P<0.005). AOF was estimated by the combination of hyaluronic acid, glycaemia, AST, ALT, platelets and prothrombin index ((a) R(2) =0.530), while FD was estimated by hyaluronic acid, glycaemia, AST/ALT, weight and platelets ((a) R(2) =0.529). (ii) Evaluation. Although NASH-CRN was a better system for fibrosis staging, Metavir staging was a better reference for blood test. Thus, the patient rate with predictive values ≥90% by tests was 97.3% with Metavir reference vs. 66.5% with NASH-CRN reference (P<10(-3)). FibroMeter showed a significantly higher AUROC than the NAFLD fibrosis score for significant fibrosis, but not for severe fibrosis or cirrhosis, with both staging systems. Relationships between fibrosis lesions were well reflected by blood tests, e.g., the correlation between histological area and FD of fibrosis (r(s) =0.971, P<10(-3)) was well reflected by the relationship between respective blood tests (r(s) =0.852, P<10(-3)). Different characteristics of fibrosis in NAFLD can be diagnosed and quantified by blood tests with excellent accuracy. © 2010 John Wiley & Sons A/S.

Design framework for spherical microphone and loudspeaker arrays in a multiple-input multiple-output system.

PubMed

Morgenstern, Hai; Rafaely, Boaz; Noisternig, Markus

2017-03-01

Spherical microphone arrays (SMAs) and spherical loudspeaker arrays (SLAs) facilitate the study of room acoustics due to the three-dimensional analysis they provide. More recently, systems that combine both arrays, referred to as multiple-input multiple-output (MIMO) systems, have been proposed due to the added spatial diversity they facilitate. The literature provides frameworks for designing SMAs and SLAs separately, including error analysis from which the operating frequency range (OFR) of an array is defined. However, such a framework does not exist for the joint design of a SMA and a SLA that comprise a MIMO system. This paper develops a design framework for MIMO systems based on a model that addresses errors and highlights the importance of a matched design. Expanding on a free-field assumption, errors are incorporated separately for each array and error bounds are defined, facilitating error analysis for the system. The dependency of the error bounds on the SLA and SMA parameters is studied and it is recommended that parameters should be chosen to assure matched OFRs of the arrays in MIMO system design. A design example is provided, demonstrating the superiority of a matched system over an unmatched system in the synthesis of directional room impulse responses.

Problems in Defining the Field of Distance Education.

ERIC Educational Resources Information Center

Keegan, Desmond

1988-01-01

This discussion of definitions of distance education responds to previous articles attempting to define the field. Topics discussed include distance education versus conventional education; group-based distance education; differences between open learning and distance education; and criteria to define distance education. (13 references) (LRW)

Approaches to Enhancing Cyber Resilience: Report of the North Atlantic Treaty Organization (NATO) Workshop IST-153

DTIC Science & Technology

2018-04-01

referred to as “defense in depth” and has been the standard model of information security management for at least a decade. Concepts such as mandatory...instrumentation into the system and monitoring this instrumentation with appropriate reports and alerts (e.g., security information event management tools or...Coalition Battle Management Language (C-BML) (NATO 2012) define information (orders, plans, reports, requests, etc.) that can be readily processed by

Decomposing Oncogenic Transcriptional Signatures to Generate Maps of Divergent Cellular States* | Office of Cancer Genomics

Cancer.gov

The systematic sequencing of the cancer genome has led to the identification of numerous genetic alterations in cancer. However, a deeper understanding of the functional consequences of these alterations is necessary to guide appropriate therapeutic strategies. Here, we describe Onco-GPS (OncoGenic Positioning System), a data-driven analysis framework to organize individual tumor samples with shared oncogenic alterations onto a reference map defined by their underlying cellular states.

Factors influencing superimposition error of 3D cephalometric landmarks by plane orientation method using 4 reference points: 4 point superimposition error regression model.

PubMed

Hwang, Jae Joon; Kim, Kee-Deog; Park, Hyok; Park, Chang Seo; Jeong, Ho-Gul

2014-01-01

Superimposition has been used as a method to evaluate the changes of orthodontic or orthopedic treatment in the dental field. With the introduction of cone beam CT (CBCT), evaluating 3 dimensional changes after treatment became possible by superimposition. 4 point plane orientation is one of the simplest ways to achieve superimposition of 3 dimensional images. To find factors influencing superimposition error of cephalometric landmarks by 4 point plane orientation method and to evaluate the reproducibility of cephalometric landmarks for analyzing superimposition error, 20 patients were analyzed who had normal skeletal and occlusal relationship and took CBCT for diagnosis of temporomandibular disorder. The nasion, sella turcica, basion and midpoint between the left and the right most posterior point of the lesser wing of sphenoidal bone were used to define a three-dimensional (3D) anatomical reference co-ordinate system. Another 15 reference cephalometric points were also determined three times in the same image. Reorientation error of each landmark could be explained substantially (23%) by linear regression model, which consists of 3 factors describing position of each landmark towards reference axes and locating error. 4 point plane orientation system may produce an amount of reorientation error that may vary according to the perpendicular distance between the landmark and the x-axis; the reorientation error also increases as the locating error and shift of reference axes viewed from each landmark increases. Therefore, in order to reduce the reorientation error, accuracy of all landmarks including the reference points is important. Construction of the regression model using reference points of greater precision is required for the clinical application of this model.

Evaluating a hybrid three-dimensional metrology system: merging data from optical and touch probe devices

NASA Astrophysics Data System (ADS)

Gerde, Janice R.; Christens-Barry, William A.

2011-08-01

In a project to meet requirements for CBP Laboratory analysis of footwear under the Harmonized Tariff Schedule of the United States (HTSUS), a hybrid metrology system comprising both optical and touch probe devices has been assembled. A unique requirement must be met: To identify the interface-typically obscured in samples of concern-of the "external surface area upper" (ESAU) and the sole without physically destroying the sample. The sample outer surface is determined by discrete point cloud coordinates obtained using laser scanner optical measurements. Measurements from the optically inaccessible insole region are obtained using a coordinate measuring machine (CMM). That surface similarly is defined by point cloud data. Mathematically, the individual CMM and scanner data sets are transformed into a single, common reference frame. Custom software then fits a polynomial surface to the insole data and extends it to intersect the mesh fitted to the outer surface point cloud. This line of intersection defines the required ESAU boundary, thus permitting further fractional area calculations to determine the percentage of materials present. With a draft method in place, and first-level method validation underway, we examine the transformation of the two dissimilar data sets into the single, common reference frame. We also will consider the six previously-identified potential error factors versus the method process. This paper reports our on-going work and discusses our findings to date.

Defining and quantifying the resilience of responses to disturbance: a conceptual and modelling approach from soil science

PubMed Central

Todman, L. C.; Fraser, F. C.; Corstanje, R.; Deeks, L. K.; Harris, J. A.; Pawlett, M.; Ritz, K.; Whitmore, A. P.

2016-01-01

There are several conceptual definitions of resilience pertaining to environmental systems and, even if resilience is clearly defined in a particular context, it is challenging to quantify. We identify four characteristics of the response of a system function to disturbance that relate to “resilience”: (1) degree of return of the function to a reference level; (2) time taken to reach a new quasi-stable state; (3) rate (i.e. gradient) at which the function reaches the new state; (4) cumulative magnitude of the function (i.e. area under the curve) before a new state is reached. We develop metrics to quantify these characteristics based on an analogy with a mechanical spring and damper system. Using the example of the response of a soil function (respiration) to disturbance, we demonstrate that these metrics effectively discriminate key features of the dynamic response. Although any one of these characteristics could define resilience, each may lead to different insights and conclusions. The salient properties of a resilient response must thus be identified for different contexts. Because the temporal resolution of data affects the accurate determination of these metrics, we recommend that at least twelve measurements are made over the temporal range for which the response is expected. PMID:27329053

Space Operations Center, shuttle interaction study, volume 1

NASA Technical Reports Server (NTRS)

1981-01-01

The feasibility of the shuttle remote manipulator system (SRMS)-aided space operations center (SOC)/orbiter berthing was evaluated to determine: (1) whether the initial rates between the SOC and the orbiter can be removed by the arm; (2) what is the best strategy to be used; (3) whether the post-capture and maneuvering loads are within the capability of the SRMS; (4) can the SOC berthing port be brought in the immediate proximity of the orbiter berthing port; and (5) what is the best way to remove the residual relative motions. Various notational conventions are established and various important locations on the orbiter and SOC structures are defined. Reference frames are defined together with the mass properties of both the SOC and the orbiter.

Reference-material system for estimating health and environmental risks of selected material cycles and energy systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crowther, M.A.; Moskowitz, P.D.

1981-07-01

Sample analyses and detailed documentation are presented for a Reference Material System (RMS) to estimate health and environmental risks of different material cycles and energy systems. Data inputs described include: end-use material demands, efficiency coefficients, environmental emission coefficients, fuel demand coefficients, labor productivity estimates, and occupational health and safety coefficients. Application of this model permits analysts to estimate fuel use (e.g., Btu), occupational risk (e.g., fatalities), and environmental emissions (e.g., sulfur oxide) for specific material trajectories or complete energy systems. Model uncertainty is quantitatively defined by presenting a range of estimates for each data input. Systematic uncertainty not quantified relatesmore » to the boundaries chosen for analysis and reference system specification. Although the RMS can be used to analyze material system impacts for many different energy technologies, it was specifically used to examine the health and environmental risks of producing the following four types of photovoltaic devices: silicon n/p single-crystal cells produced by a Czochralski process; silicon metal/insulator/semiconductor (MIS) cells produced by a ribbon-growing process; cadmium sulfide/copper sulfide backwall cells produced by a spray deposition process; and gallium arsenide cells with 500X concentrator produced by a modified Czochralski process. Emission coefficients for particulates, sulfur dioxide and nitrogen dioxide; solid waste; total suspended solids in water; and, where applicable, air and solid waste residuals for arsenic, cadmium, gallium, and silicon are examined and presented. Where data are available the coefficients for particulates, sulfur oxides, and nitrogen oxides include both process and on-site fuel-burning emissions.« less

Vibration of a flexible spacecraft with momentum exchange controllers

NASA Technical Reports Server (NTRS)

Canavin, J. R.

1976-01-01

Floating reference frames were investigated in order to allow first order vibration analysis in the presence of large system rotations. When the deformations of an elastic continuum are expanded in terms of the free-free modes of an unconstrained system, the rigid body modes are found to be fixed relative to the Tisserand frame, with respect to which the relative momentum is zero. The proof presented for this is based on the orthogonality condition for modes with distinct natural frequencies. This result also guarantees the independence of coordinates for all modes with nonzero natural frequencies. A Modified Tisserand Constraint is introduced in order to define a floating reference frame with similar properties for an elastic body which contains a spinning rotor. Finite element equations of motion are derived for a completely flexible spacecraft with momentum exchange controllers, using a Modified Tisserand Frame. The deformable systems covered in this application are assumed to undergo only small rotations, and therefore the rotor torques must formally be small, although in engineering applications it may be possible to relax this constraint. A modal analysis is performed for the system and the resulting set of equations is reduced in number by a truncation procedure for more efficient system simulation.

Controllable spectrum artificial sunlight source system using LEDs with 32 different peak wavelengths of 385-910 nm.

PubMed

Fujiwara, Kazuhiro; Yano, Akira

2011-04-01

This study developed a lighting system that produces an approximate spectral irradiance (SI) of ground level sunlight in the wavelength range of 385-910 nm (GLS₃₈₅₋₉₁₀) using 547 light-emitting diodes (LEDs) with 32 different peak wavelengths. The produced SI can be modified over an arbitrary wavelength band. The SI at the light outlet reached up to 1/2 of the GLS₃₈₅₋₉₁₀ of a sunny April day, although the produced SI deviated from the GLS₃₈₅₋₉₁₀ at some wavelengths. For subsequent experiments, the reference SI was defined as 1/4 GLS₃₈₅₋₉₁₀ of a sunny April day. The SI produced from the lighting system was adjusted to approximate the reference SI. The ratios of the produced SI and the reference SI were within 0.72-1.28. As an application of the lighting system for biological studies, the transmitted SI of a green leaf of perilla (Perilla frutescens L.) was investigated. The curve shape of the transmitted SI, which had characteristically low transmission percentages of blue and red light, reflected the characteristics of the absorption spectra of chlorophylls. The lighting system is therefore potentially beneficial for use in diagnosing physiological conditions of plant leaves, although its application is not limited to plant physiological studies. Copyright © 2010 Wiley-Liss, Inc.

A 3D visualization and guidance system for handheld optical imaging devices

NASA Astrophysics Data System (ADS)

Azar, Fred S.; de Roquemaurel, Benoit; Cerussi, Albert; Hajjioui, Nassim; Li, Ang; Tromberg, Bruce J.; Sauer, Frank

2007-03-01

We have developed a novel 3D visualization and guidance system for handheld optical imaging devices. In this paper, the system is applied to measurements of breast/cancerous tissue optical properties using a handheld diffuse optical spectroscopy (DOS) instrument. The combined guidance system/DOS instrument becomes particularly useful for monitoring neoadjuvant chemotherapy in breast cancer patients and for longitudinal studies where measurement reproducibility is critical. The system uses relatively inexpensive hardware components and comprises a 6 degrees-of-freedom (DOF) magnetic tracking device including a DC field generator, three sensors, and a PCI card running on a PC workstation. A custom-built virtual environment combined with a well-defined workflow provide the means for image-guided measurements, improved longitudinal studies of breast optical properties, 3D reconstruction of optical properties within the anatomical map, and serial data registration. The DOS instrument characterizes tissue function such as water, lipid and total hemoglobin concentration. The patient lies on her back at a 45-degrees angle. Each spectral measurement requires consistent contact with the skin, and lasts about 5-10 seconds. Therefore a limited number of positions may be studied. In a reference measurement session, the physician acquires surface points on the breast. A Delaunay-based triangulation algorithm is used to build the virtual breast surface from the acquired points. 3D locations of all DOS measurements are recorded. All subsequently acquired surfaces are automatically registered to the reference surface, thus allowing measurement reproducibility through image guidance using the reference measurements.

49 CFR 385.321 - What failures of safety management practices disclosed by the safety audit will result in a...

Code of Federal Regulations, 2013 CFR

2013-10-01

... disqualified by a State, has lost the right to operate a CMV in a State or who is disqualified to operate a... violation refers to a driver operating a CMV as defined under § 383.5. 9. § 387.7(a)—Operating a motor... Single occurrence. This violation refers to a driver operating a CMV as defined under § 390.5. 13. § 395...

49 CFR 385.321 - What failures of safety management practices disclosed by the safety audit will result in a...

Code of Federal Regulations, 2012 CFR

2012-10-01

... disqualified by a State, has lost the right to operate a CMV in a State or who is disqualified to operate a... violation refers to a driver operating a CMV as defined under § 383.5. 9. § 387.7(a)—Operating a motor... Single occurrence. This violation refers to a driver operating a CMV as defined under § 390.5. 13. § 395...

49 CFR 385.321 - What failures of safety management practices disclosed by the safety audit will result in a...

Code of Federal Regulations, 2014 CFR

2014-10-01

... disqualified by a State, has lost the right to operate a CMV in a State or who is disqualified to operate a... violation refers to a driver operating a CMV as defined under § 383.5. 9. § 387.7(a)—Operating a motor... Single occurrence. This violation refers to a driver operating a CMV as defined under § 390.5. 13. § 395...

Anatomical information in radiation treatment planning.

PubMed

Kalet, I J; Wu, J; Lease, M; Austin-Seymour, M M; Brinkley, J F; Rosse, C

1999-01-01

We report on experience and insights gained from prototyping, for clinical radiation oncologists, a new access tool for the University of Washington Digital Anatomist information resources. This access tool is designed to integrate with a radiation therapy planning (RTP) system in use in a clinical setting. We hypothesize that the needs of practitioners in a clinical setting are different from the needs of students, the original targeted users of the Digital Anatomist system, but that a common knowledge resource can serve both. Our prototype was designed to help define those differences and study the feasibility of a full anatomic reference system that will support both clinical radiation therapy and all the existing educational applications.

CHIMERA II - A real-time multiprocessing environment for sensor-based robot control

NASA Technical Reports Server (NTRS)

Stewart, David B.; Schmitz, Donald E.; Khosla, Pradeep K.

1989-01-01

A multiprocessing environment for a wide variety of sensor-based robot system, providing the flexibility, performance, and UNIX-compatible interface needed for fast development of real-time code is addressed. The requirements imposed on the design of a programming environment for sensor-based robotic control is outlined. The details of the current hardware configuration are presented, along with the details of the CHIMERA II software. Emphasis is placed on the kernel, low-level interboard communication, user interface, extended file system, user-definable and dynamically selectable real-time schedulers, remote process synchronization, and generalized interprocess communication. A possible implementation of a hierarchical control model, the NASA/NBS standard reference model for telerobot control system is demonstrated.

Ssip-a processor interconnection simulator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Navaux, P.; Weber, R.; Prezzi, J.

1982-01-01

Recent growing interest in multiple processor architectures has given rise to the study of procesor-memory interconnections for the determination of better architectures. This paper concerns the development of the SSIP-sistema simulador de interconexao de processadores (processor interconnection simulating system) which allows the evaluation of different interconnection structures comparing its performance in order to provide parameters which would help the designer to define an architcture. A wide spectrum of systems may be evaluated, and their behaviour observed due to the features incorporated into the simulator program. The system modelling and the simulator program implementation are described. Some results that can bemore » obtained are shown, along with the discussion of their usefulness. 12 references.« less

An analysis of electronic document management in oncology care.

PubMed

Poulter, Thomas; Gannon, Brian; Bath, Peter A

2012-06-01

In this research in progress, a reference model for the use of electronic patient record (EPR) systems in oncology is described. The model, termed CICERO, comprises technical and functional components, and emphasises usability, clinical safety and user acceptance. One of the functional components of the model-an electronic document and records management (EDRM) system-is monitored in the course of its deployment at a leading oncology centre in the UK. Specifically, the user requirements and design of the EDRM solution are described.The study is interpretative and forms part a wider research programme to define and validate the CICERO model. Preliminary conclusions confirm the importance of a socio-technical perspective in Onco-EPR system design.

In vitro validation and reliability study of electromagnetic skin sensors for evaluation of end range of motion positions of the hip.

PubMed

Audenaert, E A; Vigneron, L; Van Hoof, T; D'Herde, K; van Maele, G; Oosterlinck, D; Pattyn, C

2011-12-01

There is growing evidence that femoroacetabular impingement (FAI) is a probable risk factor for the development of early osteoarthritis in the nondysplastic hip. As FAI arises with end range of motion activities, measurement errors related to skin movement might be higher than anticipated when using previously reported methods for kinematic evaluation of the hip. We performed an in vitro validation and reliability study of a noninvasive method to define pelvic and femur positions in end range of motion activities of the hip using an electromagnetic tracking device. Motion data, collected from sensors attached to the bone and skin of 11 cadaver hips, were simultaneously obtained and compared in a global reference frame. Motion data were then transposed in the hip joint local coordinate systems. Observer-related variability in locating the anatomical landmarks required to define the local coordinate system and variability of determining the hip joint center was evaluated. Angular root mean square (RMS) differences between the bony and skin sensors averaged 3.2° (SD 3.5°) and 1.8° (SD 2.3°) in the global reference frame for the femur and pelvic sensors, respectively. Angular RMS differences between the bony and skin sensors in the hip joint local coordinate systems ranged at end range of motion and dependent on the motion under investigation from 1.91 to 5.81°. The presented protocol for evaluation of hip motion seems to be suited for the 3-D description of motion relevant to the experimental and clinical evaluation of femoroacetabular impingement.

An effective XML based name mapping mechanism within StoRM

NASA Astrophysics Data System (ADS)

Corso, E.; Forti, A.; Ghiselli, A.; Magnoni, L.; Zappi, R.

2008-07-01

In a Grid environment the naming capability allows users to refer to specific data resources in a physical storage system using a high level logical identifier. This logical identifier is typically organized in a file system like structure, a hierarchical tree of names. Storage Resource Manager (SRM) services map the logical identifier to the physical location of data evaluating a set of parameters as the desired quality of services and the VOMS attributes specified in the requests. StoRM is a SRM service developed by INFN and ICTP-EGRID to manage file and space on standard POSIX and high performing parallel and cluster file systems. An upcoming requirement in the Grid data scenario is the orthogonality of the logical name and the physical location of data, in order to refer, with the same identifier, to different copies of data archived in various storage areas with different quality of service. The mapping mechanism proposed in StoRM is based on a XML document that represents the different storage components managed by the service, the storage areas defined by the site administrator, the quality of service they provide and the Virtual Organization that want to use the storage area. An appropriate directory tree is realized in each storage component reflecting the XML schema. In this scenario StoRM is able to identify the physical location of a requested data evaluating the logical identifier and the specified attributes following the XML schema, without querying any database service. This paper presents the namespace schema defined, the different entities represented and the technical details of the StoRM implementation.

SU-E-J-47: Development of a High-Precision, Image-Guided Radiotherapy, Multi- Purpose Radiation Isocenter Quality-Assurance Calibration and Checking System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, C; Yan, G; Helmig, R

2014-06-01

Purpose: To develop a system that can define the radiation isocenter and correlate this information with couch coordinates, laser alignment, optical distance indicator (ODI) settings, optical tracking system (OTS) calibrations, and mechanical isocenter walkout. Methods: Our team developed a multi-adapter, multi-purpose quality assurance (QA) and calibration device that uses an electronic portal imaging device (EPID) and in-house image-processing software to define the radiation isocenter, thereby allowing linear accelerator (Linac) components to be verified and calibrated. Motivated by the concept that each Linac component related to patient setup for image-guided radiotherapy based on cone-beam CT should be calibrated with respect tomore » the radiation isocenter, we designed multiple concentric adapters of various materials and shapes to meet the needs of MV and KV radiation isocenter definition, laser alignment, and OTS calibration. The phantom's ability to accurately define the radiation isocenter was validated on 4 Elekta Linacs using a commercial ball bearing (BB) phantom as a reference. Radiation isocenter walkout and the accuracy of couch coordinates, ODI, and OTS were then quantified with the device. Results: The device was able to define the radiation isocenter within 0.3 mm. Radiation isocenter walkout was within ±1 mm at 4 cardinal angles. By switching adapters, we identified that the accuracy of the couch position digital readout, ODI, OTS, and mechanical isocenter walkout was within sub-mm. Conclusion: This multi-adapter, multi-purpose isocenter phantom can be used to accurately define the radiation isocenter and represents a potential paradigm shift in Linac QA. Moreover, multiple concentric adapters allowed for sub-mm accuracy for the other relevant components. This intuitive and user-friendly design is currently patent pending.« less

Local electric dipole moments: A generalized approach.

PubMed

Groß, Lynn; Herrmann, Carmen

2016-09-30

We present an approach for calculating local electric dipole moments for fragments of molecular or supramolecular systems. This is important for understanding chemical gating and solvent effects in nanoelectronics, atomic force microscopy, and intensities in infrared spectroscopy. Owing to the nonzero partial charge of most fragments, "naively" defined local dipole moments are origin-dependent. Inspired by previous work based on Bader's atoms-in-molecules (AIM) partitioning, we derive a definition of fragment dipole moments which achieves origin-independence by relying on internal reference points. Instead of bond critical points (BCPs) as in existing approaches, we use as few reference points as possible, which are located between the fragment and the remainder(s) of the system and may be chosen based on chemical intuition. This allows our approach to be used with AIM implementations that circumvent the calculation of critical points for reasons of computational efficiency, for cases where no BCPs are found due to large interfragment distances, and with local partitioning schemes other than AIM which do not provide BCPs. It is applicable to both covalently and noncovalently bound systems. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Reference pricing of pharmaceuticals for Medicare: evidence from Germany, The Netherlands, and New Zealand.

PubMed

Danzon, Patricia M; Ketcham, Jonathan D

2004-01-01

This paper describes three prototypical systems of therapeutic reference pricing (RP) for pharmaceuticals--Germany, the Netherlands, and New Zealand--and examines their effects on the availability of new drugs, reimbursement levels, manufacturer prices, and out-of-pocket surcharges to patients. RP for pharmaceuticals is not simply analogous to a defined contribution approach to subsidizing insurance coverage. Although a major purpose of RP is to stimulate competition, theory suggests that the achievement of this goal is unlikely, and this is confirmed by the empirical evidence. Other effects of RP differ across countries in predictable ways, reflecting each country's system design and other cost-control policies. New Zealand's RP system has reduced reimbursement and limited the availability of new drugs, particularly more expensive drugs. Compared to these three countries, if RP were applied in the United States, it would likely have a more negative effect on prices of onpatent products because of the more competitive U.S. generic market, and on research and development (R&D) and the future supply of new drugs, because of the much larger U.S. share of global pharmaceutical sales.

Experimental Testing of a Generic Submarine Model in the DSTO Low Speed Wind Tunnel. Phase 2

DTIC Science & Technology

2014-03-01

axis, z-axis (Nm) l Model reference length (1.35 m) L Lift force (N) MRP Moment Reference Point q Dynamic pressure       2 2 1 Uρ (Pa...moment reference point ( MRP ). The moment reference point was defined as the mid-length position on the centre-line of the model. Figure 5 presents the

Considering Intermittent Dormancy in an Advanced Life Support Systems Architecture

NASA Technical Reports Server (NTRS)

Sargusingh, Miriam J.; Perry, Jay L.

2017-01-01

Many advanced human space exploration missions being considered by the National Aeronautics and Space Administration (NASA) include concepts in which in-space systems cycle between inhabited and uninhabited states. Managing the life support system (LSS) may be particularly challenged during these periods of intermittent dormancy. A study to identify LSS management challenges and considerations relating to dormancy is described. The study seeks to define concepts suitable for addressing intermittent dormancy states and to evaluate whether the reference LSS architectures being considered by the Advanced Exploration Systems (AES) Life Support Systems Project (LSSP) are sufficient to support this operational state. The primary focus of the study is the mission concept considered to be the most challenging-a crewed Mars mission with an extensive surface stay. Results from this study are presented and discussed.

Integrated Systems Health Management (ISHM) Toolkit

NASA Technical Reports Server (NTRS)

Venkatesh, Meera; Kapadia, Ravi; Walker, Mark; Wilkins, Kim

2013-01-01

A framework of software components has been implemented to facilitate the development of ISHM systems according to a methodology based on Reliability Centered Maintenance (RCM). This framework is collectively referred to as the Toolkit and was developed using General Atomics' Health MAP (TM) technology. The toolkit is intended to provide assistance to software developers of mission-critical system health monitoring applications in the specification, implementation, configuration, and deployment of such applications. In addition to software tools designed to facilitate these objectives, the toolkit also provides direction to software developers in accordance with an ISHM specification and development methodology. The development tools are based on an RCM approach for the development of ISHM systems. This approach focuses on defining, detecting, and predicting the likelihood of system functional failures and their undesirable consequences.

Towards An Improvement of Hospital Services and Streamlining of Health Care Costs: The DRG Analysis in Italy.

PubMed

Bellavia, M; Tomasello, G; Damiani, P; Damiani, F; Geraci, A; Accardo, Fm; Gioviale, Mc; Lo Monte, Ai

2012-01-01

The term Diagnosis-related Group (DRG) refers to a classification system used to assess hospital services with the aim of a better management of health care costs and improving performance. The DRG system focuses on the utilization of resources, and is not concerned with the specific type of care provided to the patient. This system highlights any diseconomies and eventual critical aspects of the hospital system. This article, starting from the history of heath care financing in Italy and pointing out the difficulty to define the "quality" of health care services, describes the variables used to evaluate correctly hospital performance based on the DRG system. These include Average Length of Stay, Average Daily Patient Load, Comparative Performance Index, and Case Mix Index.

The Naval Enlisted Aviation Maintenance Manpower System: Advancing Readiness Through Improved Utilization of Intellectual Capital

DTIC Science & Technology

2011-09-01

human capital can be. The other 2 important aspect of human capital which differentiates it from any other form of capital is its requirement to...century, management has come to accept that people, not cash, buildings, or equipment, are the critical differentiators of a business enterprise. (Fitz...capital” as what has been referred to as a “critical differentiator .” Differentiator , from the word differentiate , is defined as “to form or mark

The Impact of IEEE-1076 on VHDL (Hardware Description Language)

DTIC Science & Technology

1988-12-01

Portability simply refers to how machine-independent the language is defined. The Efficiency criterion looks at how fast a program compiles and how ...if a programming language is good. The evaluation was done to determine if IEEE Standard 1076-1987 was indeed a better version of VHDL than its...must be UNIX-based and be able to * use the tools that are common to that operating system such as lex [Lesk78I, yacc [John78] and the programming

Reference earth orbital research and applications investigations (blue book). Volume 8: Life sciences

NASA Technical Reports Server (NTRS)

1971-01-01

The functional program element for the life sciences facilities to operate aboard manned space stations is presented. The life sciences investigations will consist of the following subjects: (1) medical research, (2) vertebrate research, (3) plant research, (4) cells and tissue research, (5) invertebrate research, (6) life support and protection, and (7) man-system integration. The equipment required to provide the desired functional capability for the research facilities is defined. The goals and objectives of each research facility are described.

High Temperature Monotonic and Cyclic Deformation in a Directionally Solidified Nickel-Base Superalloy.

DTIC Science & Technology

1986-05-01

was conducted in air, using a SATEC Systems computer-controlled servohydraulic testing machine. This machine uses a minicomputer (Digital PDP 11/34...overall test program) was run. This test was performed using a feature of the SATEC machine called combinatorial feedback, which allowed a user-defined...Rn) l/T + (in Es /A)/n (4.3) Q can be calculated from 0*: b Q=n (4.4) Creep data for DS MAR-M246, containing no Hafnium, from Reference 99 was used to

Universal Frequency Domain Baseband Receiver Structure for Future Military Software Defined Radios

DTIC Science & Technology

2010-09-01

selective channels, i.e., it may have a poor performance at good conditions [4]. Military systems may require a direct sequence ( DS ) component for...frequency bins using a spreading code. This is called the MC- CDMA signal. Note that spreading does not need to cover all the subcarriers but just a few, like...preambles with appropriate frequency domain properties. A DS component can be added as usually. The FDP block then includes this code as a reference

TOPEX NASA Altimeter Operations Handbook, September 1992. Volume 6

NASA Technical Reports Server (NTRS)

Hancock, David W., III; Hayne, George S.; Purdy, Craig L.; Bull, James B.; Brooks, Ronald L.

2003-01-01

This operations handbook identifies the commands for the NASA radar altimeter for the TOPEX/Poseidon spacecraft, defines the functions of these commands, and provides supplemental reference material for use by the altimeter operations personnel. The main emphasis of this document is placed on command types, command definitions, command sequences, and operational constraints. Additional document sections describe uploadable altimeter operating parameters, the telemetry stream data contents (for both the science and the engineering data), the Missions Operations System displays, and the spacecraft and altimeter health monitors.

S.P.S.S. User's Manual #1-#4. Basic Program Construction in S.P.S.S.; S.P.S.S. Non-Procedural Statements and Procedural Commands; System Control Language and S.P.S.S.; Quick File Equate Statement Reference.

ERIC Educational Resources Information Center

Earl, Lorna L.

This series of manuals describing and illustrating the Statistical Package for the Social Sciences (SPSS) was planned as a self-teaching instrument, beginning with the basics and progressing to an advanced level. Information on what the searcher must know to define the data and write a program for preliminary analysis is contained in manual 1,…

The WSTIAC Quarterly. Volume 9, Number 4

DTIC Science & Technology

2010-04-28

elements of command– Major Eric D. Trias Captain Bryan M. Bell US Air Force You have to know the past to understand the present. — Carl Sagan This article is...Quarterly, Volume 9, Number 4 3 INTRODUCTION Carl von Clausewitz defined war as “…an act of violence intended to compel our opponent to fulfill our will...controlled systems. NOTES & REFERENCES ‡ Joint Pub 3-13 provides the doctrinal foundation for the conduct of IO in joint operations. [1] von Clausewitz, Carl

Interaction of Electromagnetic Fields with Magnetized Plasmas

DTIC Science & Technology

1994-03-31

ref. 1) and by Golde 3 (ref. 2). Two additional books, entirely on the subject of ball lightning, have been written by Singer (ref. 3) and by Barry...References 1. Martin A. Uman: Lightning, McGraw Hill Book Co. New York, N2Y. (1969), pp. £ 243-248. 2. R. H. Golde , Editor: Lightning: Vol. I. Physics of...ratio& moans with 9. A microwave aborpt ~on system. as defined in said varying .84118W field and absorb smid micro. claim X. wheretin said microwave

A system to measure the data quality of spectral remote-sensing reflectance of aquatic environments

NASA Astrophysics Data System (ADS)

Wei, Jianwei; Lee, Zhongping; Shang, Shaoling

2016-11-01

Spectral remote-sensing reflectance (Rrs, sr-1) is the key for ocean color retrieval of water bio-optical properties. Since Rrs from in situ and satellite systems are subject to errors or artifacts, assessment of the quality of Rrs data is critical. From a large collection of high quality in situ hyperspectral Rrs data sets, we developed a novel quality assurance (QA) system that can be used to objectively evaluate the quality of an individual Rrs spectrum. This QA scheme consists of a unique Rrs spectral reference and a score metric. The reference system includes Rrs spectra of 23 optical water types ranging from purple blue to yellow waters, with an upper and a lower bound defined for each water type. The scoring system is to compare any target Rrs spectrum with the reference and a score between 0 and 1 will be assigned to the target spectrum, with 1 for perfect Rrs spectrum and 0 for unusable Rrs spectrum. The effectiveness of this QA system is evaluated with both synthetic and in situ Rrs spectra and it is found to be robust. Further testing is performed with the NOMAD data set as well as with satellite Rrs over coastal and oceanic waters, where questionable or likely erroneous Rrs spectra are shown to be well identifiable with this QA system. Our results suggest that applications of this QA system to in situ data sets can improve the development and validation of bio-optical algorithms and its application to ocean color satellite data can improve the short-term and long-term products by objectively excluding questionable Rrs data.

Building a reference functional model for EHR systems.

PubMed

Sumita, Yuki; Takata, Mami; Ishitsuka, Keiju; Tominaga, Yasuyuki; Ohe, Kazuhiko

2007-09-01

Our aim was to develop a reference functional model for electric health record systems (RFM). Such a RFM is built from functions using functional descriptive elements (FDEs) and represents the static relationships between them. This paper presents a new format for describing electric health record (EHR) system functions. Questionnaire and field interview survey was conducted in five hospitals in Japan and one in the USA, to collect data on EHR system functions. Based on survey results, a reference functional list (RFL) was created, in which each EHR system function was listed and divided into 13 FDE types. By analyzing the RFL, we built the meta-functional model and the functional model using UML class diagrams. The former defines language for expressing the functional model, while the latter represents functions, FDEs and their static relationships. A total of 385 functions were represented in the RFL. Six patterns were found for the relationships between functions. The meta-functional model was created as a new format for describing functions. Examples of the functional model, which included the six patterns in the relationships between functions and 11 verbs, were created. We present the meta-functional model, which is a new description format for the functional structure and relationships. Although a more detailed description is required to apply the RFM to the semiautomatic generation of functional specification documents, our RFM can visualize functional structures and functional relationships, classify functions using multiple axes and identify the similarities and differences between functions. The RFM will promote not only the standardization of EHR systems, but also communications between system developers and healthcare providers in the EHR system-design processes. 2006 Elsevier Ireland Ltd

A Model-Driven, Science Data Product Registration Service

NASA Astrophysics Data System (ADS)

Hardman, S.; Ramirez, P.; Hughes, J. S.; Joyner, R.; Cayanan, M.; Lee, H.; Crichton, D. J.

2011-12-01

The Planetary Data System (PDS) has undertaken an effort to overhaul the PDS data architecture (including the data model, data structures, data dictionary, etc.) and to deploy an upgraded software system (including data services, distributed data catalog, etc.) that fully embraces the PDS federation as an integrated system while taking advantage of modern innovations in information technology (including networking capabilities, processing speeds, and software breakthroughs). A core component of this new system is the Registry Service that will provide functionality for tracking, auditing, locating, and maintaining artifacts within the system. These artifacts can range from data files and label files, schemas, dictionary definitions for objects and elements, documents, services, etc. This service offers a single reference implementation of the registry capabilities detailed in the Consultative Committee for Space Data Systems (CCSDS) Registry Reference Model White Book. The CCSDS Reference Model in turn relies heavily on the Electronic Business using eXtensible Markup Language (ebXML) standards for registry services and the registry information model, managed by the OASIS consortium. Registries are pervasive components in most information systems. For example, data dictionaries, service registries, LDAP directory services, and even databases provide registry-like services. These all include an account of informational items that are used in large-scale information systems ranging from data values such as names and codes, to vocabularies, services and software components. The problem is that many of these registry-like services were designed with their own data models associated with the specific type of artifact they track. Additionally these services each have their own specific interface for interacting with the service. This Registry Service implements the data model specified in the ebXML Registry Information Model (RIM) specification that supports the various artifacts above as well as offering the flexibility to support customer-defined artifacts. Key features for the Registry Service include: - Model-based configuration specifying customer-defined artifact types, metadata attributes to capture for each artifact type, supported associations and classification schemes. - A REST-based external interface that is accessible via the Hypertext Transfer Protocol (HTTP). - Federation of Registry Service instances allowing associations between registered artifacts across registries as well as queries for artifacts across those same registries. A federation also enables features such as replication and synchronization if desired for a given deployment. In addition to its use as a core component of the PDS, the generic implementation of the Registry Service facilitates its applicability as a core component in any science data archive or science data system.

Thermodynamics of mixtures of patchy and spherical colloids of different sizes: A multi-body association theory with complete reference fluid information.

PubMed

Bansal, Artee; Valiya Parambathu, Arjun; Asthagiri, D; Cox, Kenneth R; Chapman, Walter G

2017-04-28

We present a theory to predict the structure and thermodynamics of mixtures of colloids of different diameters, building on our earlier work [A. Bansal et al., J. Chem. Phys. 145, 074904 (2016)] that considered mixtures with all particles constrained to have the same size. The patchy, solvent particles have short-range directional interactions, while the solute particles have short-range isotropic interactions. The hard-sphere mixture without any association site forms the reference fluid. An important ingredient within the multi-body association theory is the description of clustering of the reference solvent around the reference solute. Here we account for the physical, multi-body clusters of the reference solvent around the reference solute in terms of occupancy statistics in a defined observation volume. These occupancy probabilities are obtained from enhanced sampling simulations, but we also present statistical mechanical models to estimate these probabilities with limited simulation data. Relative to an approach that describes only up to three-body correlations in the reference, incorporating the complete reference information better predicts the bonding state and thermodynamics of the physical solute for a wide range of system conditions. Importantly, analysis of the residual chemical potential of the infinitely dilute solute from molecular simulation and theory shows that whereas the chemical potential is somewhat insensitive to the description of the structure of the reference fluid, the energetic and entropic contributions are not, with the results from the complete reference approach being in better agreement with particle simulations.

Thermodynamics of mixtures of patchy and spherical colloids of different sizes: A multi-body association theory with complete reference fluid information

NASA Astrophysics Data System (ADS)

Bansal, Artee; Valiya Parambathu, Arjun; Asthagiri, D.; Cox, Kenneth R.; Chapman, Walter G.

2017-04-01

We present a theory to predict the structure and thermodynamics of mixtures of colloids of different diameters, building on our earlier work [A. Bansal et al., J. Chem. Phys. 145, 074904 (2016)] that considered mixtures with all particles constrained to have the same size. The patchy, solvent particles have short-range directional interactions, while the solute particles have short-range isotropic interactions. The hard-sphere mixture without any association site forms the reference fluid. An important ingredient within the multi-body association theory is the description of clustering of the reference solvent around the reference solute. Here we account for the physical, multi-body clusters of the reference solvent around the reference solute in terms of occupancy statistics in a defined observation volume. These occupancy probabilities are obtained from enhanced sampling simulations, but we also present statistical mechanical models to estimate these probabilities with limited simulation data. Relative to an approach that describes only up to three-body correlations in the reference, incorporating the complete reference information better predicts the bonding state and thermodynamics of the physical solute for a wide range of system conditions. Importantly, analysis of the residual chemical potential of the infinitely dilute solute from molecular simulation and theory shows that whereas the chemical potential is somewhat insensitive to the description of the structure of the reference fluid, the energetic and entropic contributions are not, with the results from the complete reference approach being in better agreement with particle simulations.

Modeling stock price dynamics by continuum percolation system and relevant complex systems analysis

NASA Astrophysics Data System (ADS)

Xiao, Di; Wang, Jun

2012-10-01

The continuum percolation system is developed to model a random stock price process in this work. Recent empirical research has demonstrated various statistical features of stock price changes, the financial model aiming at understanding price fluctuations needs to define a mechanism for the formation of the price, in an attempt to reproduce and explain this set of empirical facts. The continuum percolation model is usually referred to as a random coverage process or a Boolean model, the local interaction or influence among traders is constructed by the continuum percolation, and a cluster of continuum percolation is applied to define the cluster of traders sharing the same opinion about the market. We investigate and analyze the statistical behaviors of normalized returns of the price model by some analysis methods, including power-law tail distribution analysis, chaotic behavior analysis and Zipf analysis. Moreover, we consider the daily returns of Shanghai Stock Exchange Composite Index from January 1997 to July 2011, and the comparisons of return behaviors between the actual data and the simulation data are exhibited.

Visual Control for Multirobot Organized Rendezvous.

PubMed

Lopez-Nicolas, G; Aranda, M; Mezouar, Y; Sagues, C

2012-08-01

This paper addresses the problem of visual control of a set of mobile robots. In our framework, the perception system consists of an uncalibrated flying camera performing an unknown general motion. The robots are assumed to undergo planar motion considering nonholonomic constraints. The goal of the control task is to drive the multirobot system to a desired rendezvous configuration relying solely on visual information given by the flying camera. The desired multirobot configuration is defined with an image of the set of robots in that configuration without any additional information. We propose a homography-based framework relying on the homography induced by the multirobot system that gives a desired homography to be used to define the reference target, and a new image-based control law that drives the robots to the desired configuration by imposing a rigidity constraint. This paper extends our previous work, and the main contributions are that the motion constraints on the flying camera are removed, the control law is improved by reducing the number of required steps, the stability of the new control law is proved, and real experiments are provided to validate the proposal.

Opportunities and challenges in conducting systematic reviews to support development of nutrient reference values: vitamin A as an example

USDA-ARS?s Scientific Manuscript database

Nutrient reference values have significant public health and policy implications. Given the importance of defining reliable nutrient reference values, there is a need for an explicit, objective, and transparent process to set these values. The Tufts Medical Center Evidence-based Practice Center asse...

Efficacy of a Deep Learning System for Detecting Glaucomatous Optic Neuropathy Based on Color Fundus Photographs.

PubMed

Li, Zhixi; He, Yifan; Keel, Stuart; Meng, Wei; Chang, Robert T; He, Mingguang

2018-03-02

To assess the performance of a deep learning algorithm for detecting referable glaucomatous optic neuropathy (GON) based on color fundus photographs. A deep learning system for the classification of GON was developed for automated classification of GON on color fundus photographs. We retrospectively included 48 116 fundus photographs for the development and validation of a deep learning algorithm. This study recruited 21 trained ophthalmologists to classify the photographs. Referable GON was defined as vertical cup-to-disc ratio of 0.7 or more and other typical changes of GON. The reference standard was made until 3 graders achieved agreement. A separate validation dataset of 8000 fully gradable fundus photographs was used to assess the performance of this algorithm. The area under receiver operator characteristic curve (AUC) with sensitivity and specificity was applied to evaluate the efficacy of the deep learning algorithm detecting referable GON. In the validation dataset, this deep learning system achieved an AUC of 0.986 with sensitivity of 95.6% and specificity of 92.0%. The most common reasons for false-negative grading (n = 87) were GON with coexisting eye conditions (n = 44 [50.6%]), including pathologic or high myopia (n = 37 [42.6%]), diabetic retinopathy (n = 4 [4.6%]), and age-related macular degeneration (n = 3 [3.4%]). The leading reason for false-positive results (n = 480) was having other eye conditions (n = 458 [95.4%]), mainly including physiologic cupping (n = 267 [55.6%]). Misclassification as false-positive results amidst a normal-appearing fundus occurred in only 22 eyes (4.6%). A deep learning system can detect referable GON with high sensitivity and specificity. Coexistence of high or pathologic myopia is the most common cause resulting in false-negative results. Physiologic cupping and pathologic myopia were the most common reasons for false-positive results. Copyright © 2018 American Academy of Ophthalmology. Published by Elsevier Inc. All rights reserved.

Separation of musical instruments based on amplitude and frequency comodulation

NASA Astrophysics Data System (ADS)

Jacobson, Barry D.; Cauwenberghs, Gert; Quatieri, Thomas F.

2002-05-01

In previous work, amplitude comodulation was investigated as a basis for monaural source separation. Amplitude comodulation refers to similarities in amplitude envelopes of individual spectral components emitted by particular types of sources. In many types of musical instruments, amplitudes of all resonant modes rise/fall, and start/stop together during the course of normal playing. We found that under certain well-defined conditions, a mixture of constant frequency, amplitude comodulated sources can unambiguously be decomposed into its constituents on the basis of these similarities. In this work, system performance was improved by relaxing the constant frequency requirement. String instruments, for example, which are normally played with vibrato, are both amplitude and frequency comodulated sources, and could not be properly tracked under the constant frequency assumption upon which our original algorithm was based. Frequency comodulation refers to similarities in frequency variations of individual harmonics emitted by these types of sources. The analytical difficulty is in defining a representation of the source which properly tracks frequency varying components. A simple, fixed filter bank can only track an individual spectral component for the duration in which it is within the passband of one of the filters. Alternatives are therefore explored which are amenable to real-time implementation.

Performance Assessment Uncertainty Analysis for Japan's HLW Program Feasibility Study (H12)

DOE Office of Scientific and Technical Information (OSTI.GOV)

BABA,T.; ISHIGURO,K.; ISHIHARA,Y.

1999-08-30

Most HLW programs in the world recognize that any estimate of long-term radiological performance must be couched in terms of the uncertainties derived from natural variation, changes through time and lack of knowledge about the essential processes. The Japan Nuclear Cycle Development Institute followed a relatively standard procedure to address two major categories of uncertainty. First, a FEatures, Events and Processes (FEPs) listing, screening and grouping activity was pursued in order to define the range of uncertainty in system processes as well as possible variations in engineering design. A reference and many alternative cases representing various groups of FEPs weremore » defined and individual numerical simulations performed for each to quantify the range of conceptual uncertainty. Second, parameter distributions were developed for the reference case to represent the uncertainty in the strength of these processes, the sequencing of activities and geometric variations. Both point estimates using high and low values for individual parameters as well as a probabilistic analysis were performed to estimate parameter uncertainty. A brief description of the conceptual model uncertainty analysis is presented. This paper focuses on presenting the details of the probabilistic parameter uncertainty assessment.« less

Substitution of Hospital Care with Primary Care: Defining the Conditions of Primary Care Plus

PubMed Central

Kroese, Mariëlle Elisabeth Aafje Lydia; Spreeuwenberg, Marieke Dingena; Elissen, Arianne Mathilda Josephus; Meerlo, Ronald Johan; Hanraets, Monique Margaretha Henriëtte; Ruwaard, Dirk

2016-01-01

Objective: To analyse barriers and facilitators in substituting hospital care with primary care to define preconditions for successful implementation. Methods: A descriptive feasibility study was performed to collect information on the feasibility of substituting hospital care with primary care. General practitioners were able to refer patients, about whom they had doubts regarding diagnosis, treatment and/or the need to refer to hospital care, to medical specialists who performed low-complex consultations at general practitioner practices. Qualitative data were collected through interviews with general practitioners and medical specialists, focus groups and notes from meetings in the Netherlands between April 2013 and January 2014. Data were analysed using a conventional content analysis which resulted in categorised barriers, facilitators and policy adjustments, after which preconditions were formulated. Results: The most important preconditions were make arrangements on governmental level, arrange a collective integrated IT-system, determine the appropriate profile for medical specialists, design a referral protocol for eligible patients, arrange deliberation possibilities for general practitioners and medical specialists and formulate a diagnostic protocol. Conclusions: The barriers, facilitators and formulated preconditions provided relevant input to change the design of substituting hospital care with primary care. PMID:27616956

Gravity influences the visual representation of object tilt in parietal cortex.

PubMed

Rosenberg, Ari; Angelaki, Dora E

2014-10-22

Sensory systems encode the environment in egocentric (e.g., eye, head, or body) reference frames, creating inherently unstable representations that shift and rotate as we move. However, it is widely speculated that the brain transforms these signals into an allocentric, gravity-centered representation of the world that is stable and independent of the observer's spatial pose. Where and how this representation may be achieved is currently unknown. Here we demonstrate that a subpopulation of neurons in the macaque caudal intraparietal area (CIP) visually encodes object tilt in nonegocentric coordinates defined relative to the gravitational vector. Neuronal responses to the tilt of a visually presented planar surface were measured with the monkey in different spatial orientations (upright and rolled left/right ear down) and then compared. This revealed a continuum of representations in which planar tilt was encoded in a gravity-centered reference frame in approximately one-tenth of the comparisons, intermediate reference frames ranging between gravity-centered and egocentric in approximately two-tenths of the comparisons, and in an egocentric reference frame in less than half of the comparisons. Altogether, almost half of the comparisons revealed a shift in the preferred tilt and/or a gain change consistent with encoding object orientation in nonegocentric coordinates. Through neural network modeling, we further show that a purely gravity-centered representation of object tilt can be achieved directly from the population activity of CIP-like units. These results suggest that area CIP may play a key role in creating a stable, allocentric representation of the environment defined relative to an "earth-vertical" direction. Copyright © 2014 the authors 0270-6474/14/3414170-11$15.00/0.

Automation and Robotics for Human Mars Exploration (AROMA)

NASA Technical Reports Server (NTRS)

Hofmann, Peter; von Richter, Andreas

2003-01-01

Automation and Robotics (A&R) systems are a key technology for Mars exploration. All over the world initiatives in this field aim at developing new A&R systems and technologies for planetary surface exploration. From December 2000 to February 2002 Kayser-Threde GmbH, Munich, Germany lead a study called AROMA (Automation and Robotics for Human Mars Exploration) under ESA contract in order to define a reference architecture of A&R elements in support of a human Mars exploration program. One of the goals of this effort is to initiate new developments and to maintain the competitiveness of European industry within this field. c2003 Published by Elsevier Science Ltd.

The flight planning - flight management connection

NASA Technical Reports Server (NTRS)

Sorensen, J. A.

1984-01-01

Airborne flight management systems are currently being implemented to minimize direct operating costs when flying over a fixed route between a given city pair. Inherent in the design of these systems is that the horizontal flight path and wind and temperature models be defined and input into the airborne computer before flight. The wind/temperature model and horizontal path are products of the flight planning process. Flight planning consists of generating 3-D reference trajectories through a forecast wind field subject to certain ATC and transport operator constraints. The interrelationships between flight management and flight planning are reviewed, and the steps taken during the flight planning process are summarized.

Automation and Robotics for Human Mars Exploration (AROMA).

PubMed

Hofmann, Peter; von Richter, Andreas

2003-01-01

Automation and Robotics (A&R) systems are a key technology for Mars exploration. All over the world initiatives in this field aim at developing new A&R systems and technologies for planetary surface exploration. From December 2000 to February 2002 Kayser-Threde GmbH, Munich, Germany lead a study called AROMA (Automation and Robotics for Human Mars Exploration) under ESA contract in order to define a reference architecture of A&R elements in support of a human Mars exploration program. One of the goals of this effort is to initiate new developments and to maintain the competitiveness of European industry within this field. c2003 Published by Elsevier Science Ltd.

On differential transformations between Cartesian and curvilinear (geodetic) coordinates

NASA Technical Reports Server (NTRS)

Soler, T.

1976-01-01

Differential transformations are developed between Cartesian and curvilinear orthogonal coordinates. Only matrix algebra is used for the presentation of the basic concepts. After defining the reference systems used the rotation (R), metric (H), and Jacobian (J) matrices of the transformations between cartesian and curvilinear coordinate systems are introduced. A value of R as a function of H and J is presented. Likewise an analytical expression for J(-1) as a function of H(-2) and R is obtained. Emphasis is placed on showing that differential equations are equivalent to conventional similarity transformations. Scaling methods are discussed along with ellipsoidal coordinates. Differential transformations between elipsoidal and geodetic coordinates are established.

Graphic and cultural aspects of pictograms: an information ergonomics viewpoint.

PubMed

Spinillo, Carla Galvão

2012-01-01

The use of pictograms is discussed considering their information content, graphic complexity and cultural dimension. The resemblance and the illusion theories are highlighted to define pictogram as a salience-based representation system, which communicational efficacy depends upon historical and cultural aspects in their interpretation. Thus, the competence in interpreting pictograms is considered relative to users' acquaintance with the pictorial system and with the referents. Pictogram as a general/neutral visual statement is questioned, pointing out the cultural and gender attributes added to pictures to represent people, professions and social events. As a result of this discussion, some critical points of the standardization of pictograms are presented.

Preliminary study of the space adaptation of the MELiSSA life support system

NASA Astrophysics Data System (ADS)

Mas-Albaigès, Joan L.; Duatis, Jordi; Podhajsky, Sandra; Guirado, Víctor; Poughon, Laurent

MELiSSA (Micro-Ecological Life Support System Alternative) is an European Space Agency (ESA) project focused on the development of a closed regenerative life support system to aid the development of technologies for future life support systems for long term manned planetary missions, e.g. a lunar base or missions to Mars. In order to understand the potential evolution of the MELiSSA concept towards its future use in the referred manned planetary mission context the MELiSSA Space Adaptation (MSA) activity has been undertaken. MSA's main objective is to model the different MELiSSA compartments using EcosimPro R , a specialized simulation tool for life support applications, in order to define a preliminary MELiSSA implementation for service in a man-tended lunar base scenario, with a four-member crew rotating in six-month increments, and performing the basic LSS functions of air revitalization, food production, and waste and water recycling. The MELiSSA EcosimPro R Model features a dedicated library for the different MELiSSA elements (bioreactors, greenhouse, crew, interconnecting elements, etc.). It is used to dimension the MELiSSA system in terms of major parameters like mass, volume and energy needs, evaluate the accuracy of the results and define the strategy for a progressive loop closure from the initial required performance (approx.100 The MELiSSA configuration(s) obtained through the EcosimPro R simulation are further analysed using the Advanced Life Support System Evaluation (ALISSE) metric, relying on mass, energy, efficiency, human risk, system reliability and crew time, for trade-off and optimization of results. The outcome of the MSA activity is, thus, a potential Life Support System architecture description, based on combined MELiSSA and other physico-chemical technologies, defining its expected performance, associated operational conditions and logistic needs.

Personal identification based on blood vessels of retinal fundus images

NASA Astrophysics Data System (ADS)

Fukuta, Keisuke; Nakagawa, Toshiaki; Hayashi, Yoshinori; Hatanaka, Yuji; Hara, Takeshi; Fujita, Hiroshi

2008-03-01

Biometric technique has been implemented instead of conventional identification methods such as password in computer, automatic teller machine (ATM), and entrance and exit management system. We propose a personal identification (PI) system using color retinal fundus images which are unique to each individual. The proposed procedure for identification is based on comparison of an input fundus image with reference fundus images in the database. In the first step, registration between the input image and the reference image is performed. The step includes translational and rotational movement. The PI is based on the measure of similarity between blood vessel images generated from the input and reference images. The similarity measure is defined as the cross-correlation coefficient calculated from the pixel values. When the similarity is greater than a predetermined threshold, the input image is identified. This means both the input and the reference images are associated to the same person. Four hundred sixty-two fundus images including forty-one same-person's image pairs were used for the estimation of the proposed technique. The false rejection rate and the false acceptance rate were 9.9×10 -5% and 4.3×10 -5%, respectively. The results indicate that the proposed method has a higher performance than other biometrics except for DNA. To be used for practical application in the public, the device which can take retinal fundus images easily is needed. The proposed method is applied to not only the PI but also the system which warns about misfiling of fundus images in medical facilities.

Prediction and explanation in the multiverse

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garriga, J.; Vilenkin, A.

2008-02-15

Probabilities in the multiverse can be calculated by assuming that we are typical representatives in a given reference class. But is this class well defined? What should be included in the ensemble in which we are supposed to be typical? There is a widespread belief that this question is inherently vague, and that there are various possible choices for the types of reference objects which should be counted in. Here we argue that the 'ideal' reference class (for the purpose of making predictions) can be defined unambiguously in a rather precise way, as the set of all observers with identicalmore » information content. When the observers in a given class perform an experiment, the class branches into subclasses who learn different information from the outcome of that experiment. The probabilities for the different outcomes are defined as the relative numbers of observers in each subclass. For practical purposes, wider reference classes can be used, where we trace over all information which is uncorrelated to the outcome of the experiment, or whose correlation with it is beyond our current understanding. We argue that, once we have gathered all practically available evidence, the optimal strategy for making predictions is to consider ourselves typical in any reference class we belong to, unless we have evidence to the contrary. In the latter case, the class must be correspondingly narrowed.« less

Study of reactor Brayton power systems for nuclear electric spacecraft

NASA Technical Reports Server (NTRS)

1979-01-01

The feasibility of using Brayton power systems for nuclear electric spacecraft was investigated. The primary performance parameters of systems mass and radiator area were determined for systems from 100 to 1000 kW sub e. Mathematical models of all system components were used to determine masses and volumes. Two completely independent systems provide propulsion power so that no single-point failure can jeopardize a mission. The waste heat radiators utilize armored heat pipes to limit meteorite puncture. The armor thickness was statistically determined to achieve the required probability of survival. A 400 kW sub e reference system received primary attention as required by the contract. The components of this system were defined and a conceptual layout was developed with encouraging results. An arrangement with redundant Brayton power systems having a 1500 K (2240 F) turbine inlet temperature was shown to be compatible with the dimensions of the space shuttle orbiter payload bay.

Datum maintenance of the main Egyptian geodetic control networks by utilizing Precise Point Positioning "PPP" technique

NASA Astrophysics Data System (ADS)

Rabah, Mostafa; Elmewafey, Mahmoud; Farahan, Magda H.

2016-06-01

A geodetic control network is the wire-frame or the skeleton on which continuous and consistent mapping, Geographic Information Systems (GIS), and surveys are based. Traditionally, geodetic control points are established as permanent physical monuments placed in the ground and precisely marked, located, and documented. With the development of satellite surveying methods and their availability and high degree of accuracy, a geodetic control network could be established by using GNSS and referred to an international terrestrial reference frame used as a three-dimensional geocentric reference system for a country. Based on this concept, in 1992, the Egypt Survey Authority (ESA) established two networks, namely High Accuracy Reference Network (HARN) and the National Agricultural Cadastral Network (NACN). To transfer the International Terrestrial Reference Frame to the HARN, the HARN was connected with four IGS stations. The processing results were 1:10,000,000 (Order A) for HARN and 1:1,000,000 (Order B) for NACN relative network accuracy standard between stations defined in ITRF1994 Epoch1996. Since 1996, ESA did not perform any updating or maintaining works for these networks. To see how non-performing maintenance degrading the values of the HARN and NACN, the available HARN and NACN stations in the Nile Delta were observed. The Processing of the tested part was done by CSRS-PPP Service based on utilizing Precise Point Positioning "PPP" and Trimble Business Center "TBC". The study shows the feasibility of Precise Point Positioning in updating the absolute positioning of the HARN network and its role in updating the reference frame (ITRF). The study also confirmed the necessity of the absent role of datum maintenance of Egypt networks.

Category mistakes: A barrier to effective environmental management.

PubMed

Wallace, Ken J; Jago, Mark

2017-09-01

How entities, the things that exist, are defined and categorised affects all aspects of environmental management including technical descriptions, quantitative analyses, participatory processes, planning, and decisions. Consequently, ambiguous definitions and wrongly assigning entities to categories, referred to as category mistakes, are barriers to effective management. Confusion caused by treating the term 'biodiversity' variously as the property of an area, the biota of an area, and a preferred end state (a value) - quite different categories of entities - is one example. To overcome such difficulties, we develop and define four entity categories - elements, processes, properties, and values - and two derived categories - states and systems. We argue that adoption of these categories and definitions will significantly improve environmental communication and analysis, and thus strengthen planning and decision-making. Copyright © 2017 Elsevier Ltd. All rights reserved.

How to Enter, Fly In, and Exit the A-Train Constellation

NASA Technical Reports Server (NTRS)

Vincent, Mark A.

2015-01-01

The collaborative science obtained from the satellites in the A-Train is an unparalleled success. The constellation framework that has evolved is well-formulated and documented by its international members. Communication between teams is enhanced by a web-based Constellation Coordination System. Safety and correlated observations are ensured by defining independent control boxes with buffers in between. Each mission stays within its control box by regular drag makeup maneuvers. Annual inclination adjustments are coordinated by all missions to maintain their absolute and relative Mean Local Time of Ascending Node (MLTAN). Since the satellites are in different orbit planes their separation involves a three-dimensional triad made up of the along track separations, reference groundtracks and MLTAN's. For further safety, a Constellation Envelope has been defined to determine safe entry and exit orbits.

Magnetic Coordinate Systems

NASA Astrophysics Data System (ADS)

Laundal, K. M.; Richmond, A. D.

2017-03-01

Geospace phenomena such as the aurora, plasma motion, ionospheric currents and associated magnetic field disturbances are highly organized by Earth's main magnetic field. This is due to the fact that the charged particles that comprise space plasma can move almost freely along magnetic field lines, but not across them. For this reason it is sensible to present such phenomena relative to Earth's magnetic field. A large variety of magnetic coordinate systems exist, designed for different purposes and regions, ranging from the magnetopause to the ionosphere. In this paper we review the most common magnetic coordinate systems and describe how they are defined, where they are used, and how to convert between them. The definitions are presented based on the spherical harmonic expansion coefficients of the International Geomagnetic Reference Field (IGRF) and, in some of the coordinate systems, the position of the Sun which we show how to calculate from the time and date. The most detailed coordinate systems take the full IGRF into account and define magnetic latitude and longitude such that they are constant along field lines. These coordinate systems, which are useful at ionospheric altitudes, are non-orthogonal. We show how to handle vectors and vector calculus in such coordinates, and discuss how systematic errors may appear if this is not done correctly.

Satellite services system analysis study. Volume 1, part 2: Executive summary

NASA Technical Reports Server (NTRS)

1981-01-01

The early mission model was developed through a survey of the potential user market. Service functions were defined and a group of design reference missions were selected which represented needs for each of the service functions. Servicing concepts were developed through mission analysis and STS timeline constraint analysis. The hardware needs for accomplishing the service functions were identified with emphasis being placed on applying equipment in the current NASA inventory and that in advanced stages of planning. A more comprehensive service model was developed based on the NASA and DoD mission models segregated by mission class. The number of service events of each class were estimated based on average revisit and service assumptions. Service Kits were defined as collections of equipment applicable to performing one or more service functions. Preliminary design was carrid out on a selected set of hardware needed for early service missions. The organization and costing of the satellie service systems were addressed.

Workflow computing. Improving management and efficiency of pathology diagnostic services.

PubMed

Buffone, G J; Moreau, D; Beck, J R

1996-04-01

Traditionally, information technology in health care has helped practitioners to collect, store, and present information and also to add a degree of automation to simple tasks (instrument interfaces supporting result entry, for example). Thus commercially available information systems do little to support the need to model, execute, monitor, coordinate, and revise the various complex clinical processes required to support health-care delivery. Workflow computing, which is already implemented and improving the efficiency of operations in several nonmedical industries, can address the need to manage complex clinical processes. Workflow computing not only provides a means to define and manage the events, roles, and information integral to health-care delivery but also supports the explicit implementation of policy or rules appropriate to the process. This article explains how workflow computing may be applied to health-care and the inherent advantages of the technology, and it defines workflow system requirements for use in health-care delivery with special reference to diagnostic pathology.

Space Generic Open Avionics Architecture (SGOAA) reference model technical guide

NASA Technical Reports Server (NTRS)

Wray, Richard B.; Stovall, John R.

1993-01-01

This report presents a full description of the Space Generic Open Avionics Architecture (SGOAA). The SGOAA consists of a generic system architecture for the entities in spacecraft avionics, a generic processing architecture, and a six class model of interfaces in a hardware/software system. The purpose of the SGOAA is to provide an umbrella set of requirements for applying the generic architecture interface model to the design of specific avionics hardware/software systems. The SGOAA defines a generic set of system interface points to facilitate identification of critical interfaces and establishes the requirements for applying appropriate low level detailed implementation standards to those interface points. The generic core avionics system and processing architecture models provided herein are robustly tailorable to specific system applications and provide a platform upon which the interface model is to be applied.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Elia, Valerio; Gnoni, Maria Grazia, E-mail: mariagrazia.gnoni@unisalento.it; Tornese, Fabiana

Highlights: • Pay-As-You-Throw (PAYT) schemes are becoming widespread in several countries. • Economic, organizational and technological issues have to be integrated in an efficient PAYT model design. • Efficiency refers to a PAYT system which support high citizen participation rates as well as economic sustainability. • Different steps and constraints have to be evaluated from collection services to type technologies. • An holistic approach is discussed to support PAYT systems diffusion. - Abstract: Pay-As-You-Throw (PAYT) strategies are becoming widely applied in solid waste management systems; the main purpose is to support a more sustainable – from economic, environmental and socialmore » points of view – management of waste flows. Adopting PAYT charging models increases the complexity level of the waste management service as new organizational issues have to be evaluated compared to flat charging models. In addition, innovative technological solutions could also be adopted to increase the overall efficiency of the service. Unit pricing, user identification and waste measurement represent the three most important processes to be defined in a PAYT system. The paper proposes a holistic framework to support an effective design and management process. The framework defines most critical processes and effective organizational and technological solutions for supporting waste managers as well as researchers.« less

INTEGRATION OF RELIABILITY WITH MECHANISTIC THERMALHYDRAULICS: REPORT ON APPROACH AND TEST PROBLEM RESULTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

J. S. Schroeder; R. W. Youngblood

The Risk-Informed Safety Margin Characterization (RISMC) pathway of the Light Water Reactor Sustainability Program is developing simulation-based methods and tools for analyzing safety margin from a modern perspective. [1] There are multiple definitions of 'margin.' One class of definitions defines margin in terms of the distance between a point estimate of a given performance parameter (such as peak clad temperature), and a point-value acceptance criterion defined for that parameter (such as 2200 F). The present perspective on margin is that it relates to the probability of failure, and not just the distance between a nominal operating point and a criterion.more » In this work, margin is characterized through a probabilistic analysis of the 'loads' imposed on systems, structures, and components, and their 'capacity' to resist those loads without failing. Given the probabilistic load and capacity spectra, one can assess the probability that load exceeds capacity, leading to component failure. Within the project, we refer to a plot of these probabilistic spectra as 'the logo.' Refer to Figure 1 for a notional illustration. The implications of referring to 'the logo' are (1) RISMC is focused on being able to analyze loads and spectra probabilistically, and (2) calling it 'the logo' tacitly acknowledges that it is a highly simplified picture: meaningful analysis of a given component failure mode may require development of probabilistic spectra for multiple physical parameters, and in many practical cases, 'load' and 'capacity' will not vary independently.« less

Pointing to potential reference areas to assess soil mutagenicity.

PubMed

Meyer, D D; Da Silva, F M R; Souza, J W M; Pohren, R S; Rocha, J A V; Vargas, V M F

2015-04-01

Several have been performed to evaluate the mutagenicity of soil samples in urban and industrial areas. The use of uncontaminated reference areas has been an obstacle to the study of environmental mutagenesis. The study aimed to indicate a methodology to define reference areas in studies of environmental contamination based on "Ambient Background Concentration" of metallic elements associated with the Salmonella/microsome assay. We looked at three potential reference areas, two of them close by the industrial sources of contamination (São Jerônimo reference, near the coal-fired power plant, and Triunfo reference, near the wood preservative plant), but not directly influenced by them and an area located inside a protected area (Itapuã reference). We also carried out chemical analyses of some metals to plot the metal profile of these potential reference areas and define basal levels of these metals in the soils. After examining the mutagenicity of the inorganic extracts using strains TA98, TA97a, and TA100, in the presence and absence of S9 mix, we indicated the São Jerônimo reference and the Itapuã reference as two sites that could be used in future studies of mutagenicity of soils in southern Brazil. The association between a mutagenicity bioassay and the "Ambient Background Concentration" seems to be a useful method to indicate the reference areas in studies of contamination by environmental mutagens, where these results were corroborated by canonical correspondence analysis.

Reference in human and non-human primate communication: What does it take to refer?

PubMed

Sievers, Christine; Gruber, Thibaud

2016-07-01

The concept of functional reference has been used to isolate potentially referential vocal signals in animal communication. However, its relatedness to the phenomenon of reference in human language has recently been brought into question. While some researchers have suggested abandoning the concept of functional reference altogether, others advocate a revision of its definition to include contextual cues that play a role in signal production and perception. Empirical and theoretical work on functional reference has also put much emphasis on how the receiver understands the referential signal. However, reference, as defined in the linguistic literature, is an action of the producer, and therefore, any definition describing reference in non-human animals must also focus on the producer. To successfully determine whether a signal is used to refer, we suggest an approach from the field of pragmatics, taking a closer look at specific situations of signal production, specifically at the factors that influence the production of a signal by an individual. We define the concept of signaller's reference to identify intentional acts of reference produced by a signaller independently of the communicative modality, and illustrate it with a case study of the hoo vocalizations produced by wild chimpanzees during travel. This novel framework introduces an intentional approach to referentiality. It may therefore permit a closer comparison of human and non-human animal referential behaviour and underlying cognitive processes, allowing us to identify what may have emerged solely in the human lineage.

SUPPORT FOR REFERENCE AND EQUIVALENCY PROGRAM

EPA Science Inventory

Federal Reference Methods (FRMs) and Federal Equivalent Methods (FEMs) form the backbone of the EPA's national monitoring strategy. They are the measurement methodologies that define attainment of a National Ambient Air Quality Standard (NAAQS). As knowledge and technology adva...

International Geomagnetic Reference Field: the third generation.

USGS Publications Warehouse

Peddie, N.W.

1982-01-01

In August 1981 the International Association of Geomagnetism and Aeronomy revised the International Geomagnetic Reference Field (IGRF). It is the second revision since the inception of the IGRF in 1968. The revision extends the earlier series of IGRF models from 1980 to 1985, introduces a new series of definitive models for 1965-1976, and defines a provisional reference field for 1975- 1980. The revision consists of: 1) a model of the main geomagnetic field at 1980.0, not continuous with the earlier series of IGRF models together with a forecast model of the secular variation of the main field during 1980-1985; 2) definitive models of the main field at 1965.0, 1970.0, and 1975.0, with linear interpolation of the model coefficients specified for intervening dates; and 3) a provisional reference field for 1975-1980, defined as the linear interpolation of the 1975 and 1980 main-field models.-from Author

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The Office of Civilian Radioactive Waste Management Systems Engineering Management Plan (OCRWM SEMP) specifies the technical management approach for the development of the waste management system, and specifies the approach for the development of each of the system elements -- the waste acceptance system, the transportation system, the Monitored Retrievable Storage (MRS) facility, and the mined geologic disposal system, which includes site characterization activity. The SEMP also delineates how systems engineering will be used by OCRWM to describe the system development process; it identifies responsibilities for its implementation, and specifies the minimum requirements for systems engineering. It also identifies themore » close interrelationship of system engineering and licensing processes. This SEMP, which is a combined OCRWM and M&O SEMP, is part of the top-level program documentation and is prepared in accordance with the direction provided in the Program Management System Manual (PMSM). The relationship of this document to other top level documents in the CRWMS document hierarchy is defined in the PMSM. A systems engineering management plan for each project, which specifies the actions to be taken in implementing systems engineering at the project level, shall be prepared by the respective project managers. [``Program`` refers to the CRWMS-wide activity and ``project`` refers to that level responsible for accomplishing the specific activities of that segment of the program.] The requirements for the project level SEMPs are addressed in Section 4.2.2.2. They represent the minimum set of requirements, and do not preclude the broadening of systems engineering activities to meet the specific needs of each project.« less

A cognitive mobile BTS solution with software-defined radioelectric sensing.

PubMed

Muñoz, Jorge; Alonso, Javier Vales; García, Francisco Quiñoy; Costas, Sergio; Pillado, Marcos; Castaño, Francisco Javier González; Sánchez, Manuel García; Valcarce, Roberto López; Bravo, Cristina López

2013-02-05

Private communications inside large vehicles such as ships may be effectively provided using standard cellular systems. In this paper we propose a new solution based on software-defined radio with electromagnetic sensing support. Software-defined radio allows low-cost developments and, potentially, added-value services not available in commercial cellular networks. The platform of reference, OpenBTS, only supports single-channel cells. Our proposal, however, has the ability of changing BTS channel frequency without disrupting ongoing communications. This ability should be mandatory in vehicular environments, where neighbouring cell configurations may change rapidly, so a moving cell must be reconfigured in real-time to avoid interferences. Full details about frequency occupancy sensing and the channel reselection procedure are provided in this paper. Moreover, a procedure for fast terminal detection is proposed. This may be decisive in emergency situations, e.g., if someone falls overboard. Different tests confirm the feasibility of our proposal and its compatibility with commercial GSM terminals.

A Cognitive Mobile BTS Solution with Software-Defined Radioelectric Sensing

PubMed Central

Muñoz, Jorge; Alonso, Javier Vales; García, Francisco Quiñoy; Costas, Secundino; Pillado, Marcos; Castaño, Francisco Javier González; Sánchez, Manuel Garćia; Valcarce, Roberto López; Bravo, Cristina López

2013-01-01

Private communications inside large vehicles such as ships may be effectively provided using standard cellular systems. In this paper we propose a new solution based on software-defined radio with electromagnetic sensing support. Software-defined radio allows low-cost developments and, potentially, added-value services not available in commercial cellular networks. The platform of reference, OpenBTS, only supports single-channel cells. Our proposal, however, has the ability of changing BTS channel frequency without disrupting ongoing communications. This ability should be mandatory in vehicular environments, where neighbouring cell configurations may change rapidly, so a moving cell must be reconfigured in real-time to avoid interferences. Full details about frequency occupancy sensing and the channel reselection procedure are provided in this paper. Moreover, a procedure for fast terminal detection is proposed. This may be decisive in emergency situations, e.g., if someone falls overboard. Different tests confirm the feasibility of our proposal and its compatibility with commercial GSM terminals. PMID:23385417

An evaluation of selected herbal reference texts and comparison to published reports of adverse herbal events.

PubMed

Haller, Christine A; Anderson, Ilene B; Kim, Susan Y; Blanc, Paul D

2002-01-01

There has been a recent proliferation of medical reference texts intended to guide practitioners whose patients use herbal therapies. We systematically assessed six herbal reference texts to evaluate the information they contain on herbal toxicity. We selected six major herbal references published from 1996 to 2000 to evaluate the adequacy of their toxicological information in light of published adverse events. To identify herbs most relevant to toxicology, we reviewed herbal-related calls to our regional California Poison Control System, San Francisco division (CPCS-SF) in 1998 and identified the 12 herbs (defined as botanical dietary supplements) most frequently involved in these CPCS-SF referrals. We searched Medline (1966 to 2000) to identify published reports of adverse effects potentially related to these same 12 herbs. We scored each herbal reference text on the basis of information inclusiveness for the target 12 herbs, with a maximal overall score of 3. The herbs, identified on the basis of CPCS-SF call frequency were: St John's wort, ma huang, echinacea, guarana, ginkgo, ginseng, valerian, tea tree oil, goldenseal, arnica, yohimbe and kava kava. The overall herbal reference scores ranged from 2.2 to 0.4 (median 1.1). The Natural Medicines Comprehensive Database received the highest overall score and was the most complete and useful reference source. All of the references, however, lacked sufficient information on management of herbal medicine overdose, and several had incorrect overdose management guidelines that could negatively impact patient care. Current herbal reference texts do not contain sufficient information for the assessment and management of adverse health effects of botanical therapies.

The robot and the satellite for tele-operating echographic examination in Earth isolated sites, or onboard ISS.

PubMed

Arbeille, Ph; Ruiz, J; Ayoub, J; Vieyres, P; Porcher, M; Boulay, J; Moreau, V; Poisson, G

2004-07-01

The objective was to design and validate a method for tele-operating (from an expert site) an echographic examination in an isolated site. The isolated places, defined as areas with reduced medical facilities, could be secondary hospitals 20 to 50 km from the university hospital, or dispensaries in Africa or Amazonia, or a moving structure like a rescue vehicle or the International Space Station (ISS). At the expert center, the ultrasound medical expert moves a fictive probe, connected to a computer (n degrees 1) which sends, the coordinate changes of this probe via an ISDN or satellite line to a second computer (n degrees 2), located at the isolated site, which applies them to the robotic arm holding the real echographic probe. The system was tested at Tours Hospital on 105 patients. A complete investigation (visualization) of all the organs requested for different clinical cases was obtained in 76% of the cases with the robot, and 87% at the reference echography: In 11% of the cases, at least one of the organ visualized at reference echo could not be investigated by the robot, thus the diagnostic was not done. The number of repositioning was higher for the robot (6.5 +/- 2) than for the reference echo (5.1 +/- 2 = or > 24% more with robot). The duration of the examination was higher with the robot (16 +/- 10 min) than for the reference echography (11 +/- 4 min = or > +43% with the robot compare to reference echography. The system was also tested successfully using satellite links in a limited number of cases (approx 30).

14 CFR Appendix J to Part 36 - Alternative Noise Certification Procedure for Helicopters Under Subpart H Having a Maximum...

Code of Federal Regulations, 2010 CFR

2010-01-01

... produce the same advancing blade tip Mach number as associated with the reference conditions; (i) Advancing blade tip Mach number (MAT) is defined as the ratio of the arithmetic sum of blade tip rotational... the reference advancing blade tip Mach number. The adjusted reference airspeed shall be maintained...

14 CFR Appendix J to Part 36 - Alternative Noise Certification Procedure for Helicopters Under Subpart H Having a Maximum...

Code of Federal Regulations, 2011 CFR

2011-01-01

... produce the same advancing blade tip Mach number as associated with the reference conditions; (i) Advancing blade tip Mach number (MAT) is defined as the ratio of the arithmetic sum of blade tip rotational... the reference advancing blade tip Mach number. The adjusted reference airspeed shall be maintained...

14 CFR Appendix J to Part 36 - Alternative Noise Certification Procedure for Helicopters Under Subpart H Having a Maximum...

Code of Federal Regulations, 2012 CFR

2012-01-01

... produce the same advancing blade tip Mach number as associated with the reference conditions; (i) Advancing blade tip Mach number (MAT) is defined as the ratio of the arithmetic sum of blade tip rotational... the reference advancing blade tip Mach number. The adjusted reference airspeed shall be maintained...

14 CFR Appendix J to Part 36 - Alternative Noise Certification Procedure for Helicopters Under Subpart H Having a Maximum...

Code of Federal Regulations, 2013 CFR

2013-01-01

... produce the same advancing blade tip Mach number as associated with the reference conditions; (i) Advancing blade tip Mach number (MAT) is defined as the ratio of the arithmetic sum of blade tip rotational... the reference advancing blade tip Mach number. The adjusted reference airspeed shall be maintained...

14 CFR Appendix J to Part 36 - Alternative Noise Certification Procedure for Helicopters Under Subpart H Having a Maximum...

Code of Federal Regulations, 2014 CFR

2014-01-01

... produce the same advancing blade tip Mach number as associated with the reference conditions; (i) Advancing blade tip Mach number (MAT) is defined as the ratio of the arithmetic sum of blade tip rotational... the reference advancing blade tip Mach number. The adjusted reference airspeed shall be maintained...

Guidelines for Marine Biological Reference Collections. Unesco Reports in Marine Sciences, No. 22.

ERIC Educational Resources Information Center

Hureau, J. C.; Rice, A. L.

This manual provides practical advice on the appropriation, conservation, and documentation of a marine biological reference collection, in response to needs expressed by Mediterranean Arab countries. A reference collection is defined as a working museum containing a series of specimens with which biologists are able to compare their own material.…

Motor vehicle fuel analyzer

DOEpatents

Hoffheins, B.S.; Lauf, R.J.

1997-08-05

A gas detecting system is described for classifying the type of liquid fuel in a container or tank. The system includes a plurality of semiconductor gas sensors, each of which differs from the other in its response to various organic vapors. The system includes a means of processing the responses of the plurality of sensors such that the responses to any particular organic substance or mixture is sufficiently distinctive to constitute a recognizable ``signature``. The signature of known substances are collected and divided into two classes based on some other known characteristic of the substances. A pattern recognition system classifies the signature of an unknown substance with reference to the two user-defined classes, thereby classifying the unknown substance with regard to the characteristic of interest, such as its suitability for a particular use. 14 figs.

Motor vehicle fuel analyzer

DOEpatents

Hoffheins, Barbara S.; Lauf, Robert J.

1997-01-01

A gas detecting system for classifying the type of liquid fuel in a container or tank. The system includes a plurality of semiconductor gas sensors, each of which differs from the other in its response to various organic vapors. The system includes a means of processing the responses of the plurality of sensors such that the responses to any particular organic substance or mixture is sufficiently distinctive to constitute a recognizable "signature". The signature of known substances are collected and divided into two classes based on some other known characteristic of the substances. A pattern recognition system classifies the signature of an unknown substance with reference to the two user-defined classes, thereby classifying the unknown substance with regard to the characteristic of interest, such as its suitability for a particular use.

Towards an Intelligent Textbook of Neurology

PubMed Central

Reggia, James A.; Pula, Thaddeus P.; Price, Thomas R.; Perricone, Barry T.

1980-01-01

We define an intelligent textbook of medicine to be a computer system that: (1) provides for storage and selective retrieval of synthesized clinical knowledge for reference purposes; and (2) supports the application by computer of its knowledge to patient information to assist physicians with decision making. This paper describes an experimental system called KMS (a Knowledge Management System) for creating and using intelligent medical textbooks. KMS is domain-independent, supports multiple inference methods and representation languages, and is designed for direct use by physicians during the knowledge acquisition process. It is presented here in the context of the development of an Intelligent Textbook of Neurology. We suggest that KMS has the potential to overcome some of the problems that have inhibited the use of knowledge-based systems by physicians in the past.

Quantum Anosov flows: A new family of examples

NASA Astrophysics Data System (ADS)

Peter, Ingo J.; Emch, Gérard G.

1998-09-01

A quantum version is presented for the Anosov system defined by the time evolution implemented by the geodesic coflow on the cotangent bundle of any compact quotient manifold obtained from the Poincaré half-plane. While the canonical Weyl algebra does not close under time evolution, the symplectic structure of these classical systems can be exploited to produce objects akin to the CCR algebras encountered in quantum field theory. This construction allows one to lift both the geodesic and the horocyclic flows to a Weyl algebra describing the quantum dynamics corresponding to the systems under consideration. The Anosov relations as proposed in Ref. Reference 1 are found to be valid for these models. A quantum version of the classical ergodicity of these systems is discussed in the last section.

Louisiana coastal GIS network: Graphical user interface for access to spatial data

USGS Publications Warehouse

Hiland, Matteson; McBride, Randolph A.; Davis, Donald; Braud, Dewitt; Streiffer, Henry; Jones, Farrell; Lewis, Anthony; Williams, S.

1991-01-01

Louisiana's coastal wetlands support a large percentage of the nation's seafood and fur industries, vast deposits of oil and natural gas, habitat for thousands of species of plants and animals, winter nesting grounds and migratory paths for numerous waterfowl, and many recreational resources enjoyed by residents and tourists. Louisiana's wetlands also have the highest rates of coastal erosion and wetland loss in the nation. While numerous studies across many disciplines have been conducted on both local and regional scales, no complete inventory exists for this information. The Louisiana Coastal Geographic Information System Network (LCGISN) is currently being developed to facilitate access to existing data for coastal zone planners, managers, and researchers. The Louisiana Geological Survey (LGS), in cooperation with the LSU Department of Geography and Anthropology, the Computer Aided Design and Geographic Information Systems Research Laboratory (CADGIS), and others, is pursuing this project under the terms of a cooperative agreement with the U.S. Geological Survey. LCGISN is an automated system for searching and retrieving geographic, cartographic, and bibliographic data. By linking original programming with an existing GIS software package and an industry standard relational database management system, LCGISN will provide the capability for users to search for data references by interactively defining the area of interest on a displayed map/image reference background. Several agencies will be networked to provide easy access to a wide variety of information. LCGISN, with its headquarters at LGS, will serve as the central node on the network, providing data format conversions, projection and datum transformations, and storage of several of the most commonly used data sets. Thematic mapper data, USGS 7.5-minute quadrangle map boundaries, political and legal boundaries, major transportation routes, and other digital data will provide a base map to aid the user in selecting the exact area of interest. Then, the user will set search criteria by proceeding through a series of menu-driven options. The system will then return any or all of the following: a list of digital maps or imagery that can be displayed immediately and visually overlayed, a list of maps/remotely sensed data and information on their availability, and a list of bibliographic references concerning the area and subject defined.

DAS: A Data Management System for Instrument Tests and Operations

NASA Astrophysics Data System (ADS)

Frailis, M.; Sartor, S.; Zacchei, A.; Lodi, M.; Cirami, R.; Pasian, F.; Trifoglio, M.; Bulgarelli, A.; Gianotti, F.; Franceschi, E.; Nicastro, L.; Conforti, V.; Zoli, A.; Smart, R.; Morbidelli, R.; Dadina, M.

2014-05-01

The Data Access System (DAS) is a and data management software system, providing a reusable solution for the storage of data acquired both from telescopes and auxiliary data sources during the instrument development phases and operations. It is part of the Customizable Instrument WorkStation system (CIWS-FW), a framework for the storage, processing and quick-look at the data acquired from scientific instruments. The DAS provides a data access layer mainly targeted to software applications: quick-look displays, pre-processing pipelines and scientific workflows. It is logically organized in three main components: an intuitive and compact Data Definition Language (DAS DDL) in XML format, aimed for user-defined data types; an Application Programming Interface (DAS API), automatically adding classes and methods supporting the DDL data types, and providing an object-oriented query language; a data management component, which maps the metadata of the DDL data types in a relational Data Base Management System (DBMS), and stores the data in a shared (network) file system. With the DAS DDL, developers define the data model for a particular project, specifying for each data type the metadata attributes, the data format and layout (if applicable), and named references to related or aggregated data types. Together with the DDL user-defined data types, the DAS API acts as the only interface to store, query and retrieve the metadata and data in the DAS system, providing both an abstract interface and a data model specific one in C, C++ and Python. The mapping of metadata in the back-end database is automatic and supports several relational DBMSs, including MySQL, Oracle and PostgreSQL.

Combination of an electrolytic pretreatment unit with secondary water reclamation processes

NASA Technical Reports Server (NTRS)

Wells, G. W.; Bonura, M. S.

1973-01-01

The design and fabrication of a flight concept prototype electrolytic pretreatment unit (EPU) and of a contractor-furnished air evaporation unit (AEU) are described. The integrated EPU and AEU potable water recovery system is referred to as the Electrovap and is capable of processing the urine and flush water of a six-man crew. Results of a five-day performance verification test of the Electrovap system are presented and plans are included for the extended testing of the Electrovap to produce data applicable to the combination of electrolytic pretreatment with most final potable water recovery systems. Plans are also presented for a program to define the design requirements for combining the electrolytic pretreatment unit with a reverse osmosis final processing unit.

Mount mechanisms for the Saturn 5/Apollo mobile launcher at John F. Kennedy Space Center

NASA Technical Reports Server (NTRS)

Balke, H. A.

1975-01-01

A support system was designed to resist hurricane wind loads at the launch pad and to allow the supported structural frame to expand and contract freely under wide ranges of temperature. This system consists of six mount mechanisms devised to meet the previously stated requirements plus a load-carrying capacity for each of 3.2-million kilograms (7-million pounds) downward and 1.6-million kilograms (3.5-million pounds) upward. A similar but lighter system of six mount mechanisms was designed for use in the sheltered environment of the vehicle assembly building. Each requirement and design result is discussed, and each mount mechanism is defined by location and type with references to visual presentations.

47 CFR 64.619 - VRS Access Technology Reference Platform and administrator.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Access Technology Reference Platform shall be a software product that performs consistently with the...) Compensation. The TRS Fund, as defined by § 64.604(a)(5)(iii) of this subpart, may be used to compensate the...

47 CFR 64.619 - VRS Access Technology Reference Platform and administrator.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Access Technology Reference Platform shall be a software product that performs consistently with the...) Compensation. The TRS Fund, as defined by § 64.604(a)(5)(iii) of this subpart, may be used to compensate the...

Statistical analysis of electromagnetic radiation measurements in the vicinity of GSM/UMTS base station installed on buildings in Serbia.

PubMed

Koprivica, Mladen; Slavkovic, Vladimir; Neskovic, Natasa; Neskovic, Aleksandar

2016-03-01

As a result of dense deployment of public mobile base stations, additional electromagnetic (EM) radiation occurs in the modern human environment. At the same time, public concern about the exposure to EM radiation emitted by such sources has increased. In order to determine the level of radio frequency radiation generated by base stations, extensive EM field strength measurements were carried out for 664 base station locations, from which 276 locations refer to the case of base stations with antenna system installed on buildings. Having in mind the large percentage (42 %) of locations with installations on buildings, as well as the inevitable presence of people in their vicinity, a detailed analysis of this location category was performed. Measurement results showed that the maximum recorded value of total electric field strength has exceeded International Commission on Non-Ionizing Radiation Protection general public exposure reference levels at 2.5 % of locations and Serbian national reference levels at 15.6 % of locations. It should be emphasised that the values exceeding the reference levels were observed only outdoor, while in indoor total electric field strength in no case exceeded the defined reference levels. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

The multi-reference retaining the excitation degree perturbation theory: A size-consistent, unitary invariant, and rapidly convergent wavefunction based ab initio approach

NASA Astrophysics Data System (ADS)

Fink, Reinhold F.

2009-02-01

The retaining the excitation degree (RE) partitioning [R.F. Fink, Chem. Phys. Lett. 428 (2006) 461(20 September)] is reformulated and applied to multi-reference cases with complete active space (CAS) reference wave functions. The generalised van Vleck perturbation theory is employed to set up the perturbation equations. It is demonstrated that this leads to a consistent and well defined theory which fulfils all important criteria of a generally applicable ab initio method: The theory is proven numerically and analytically to be size-consistent and invariant with respect to unitary orbital transformations within the inactive, active and virtual orbital spaces. In contrast to most previously proposed multi-reference perturbation theories the necessary condition for a proper perturbation theory to fulfil the zeroth order perturbation equation is exactly satisfied with the RE partitioning itself without additional projectors on configurational spaces. The theory is applied to several excited states of the benchmark systems CH2 , SiH2 , and NH2 , as well as to the lowest states of the carbon, nitrogen and oxygen atoms. In all cases comparisons are made with full configuration interaction results. The multi-reference (MR)-RE method is shown to provide very rapidly converging perturbation series. Energy differences between states of similar configurations converge even faster.

29 CFR 553.224 - “Work period” defined.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 29 Labor 3 2011-07-01 2011-07-01 false âWork periodâ defined. 553.224 Section 553.224 Labor... Enforcement Employees of Public Agencies Tour of Duty and Compensable Hours of Work Rules § 553.224 “Work period” defined. (a) As used in section 7(k), the term “work period” refers to any established and...

Constructivist Learning Environments and Defining the Online Learning Community

ERIC Educational Resources Information Center

Brown, Loren

2014-01-01

The online learning community is frequently referred to, but ill defined. The constructivist philosophy and approach to teaching and learning is both an effective means of constructing an online learning community and it is a tool by which to define key elements of the learning community. In order to build a nurturing, self-sustaining online…

45 CFR 506.10 - “Vietnam conflict” defined.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 45 Public Welfare 3 2014-10-01 2014-10-01 false âVietnam conflictâ defined. 506.10 Section 506.10... § 506.10 “Vietnam conflict” defined. Vietnam conflict refers to the period beginning February 28, 1961... proclaimed the date of May 7, 1975, to be the ending date of the “Vietnam era” (Presidential Proclamation No...

45 CFR 506.10 - “Vietnam conflict” defined.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 45 Public Welfare 3 2013-10-01 2013-10-01 false âVietnam conflictâ defined. 506.10 Section 506.10... § 506.10 “Vietnam conflict” defined. Vietnam conflict refers to the period beginning February 28, 1961... proclaimed the date of May 7, 1975, to be the ending date of the “Vietnam era” (Presidential Proclamation No...

45 CFR 506.10 - “Vietnam conflict” defined.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 45 Public Welfare 3 2012-10-01 2012-10-01 false âVietnam conflictâ defined. 506.10 Section 506.10... § 506.10 “Vietnam conflict” defined. Vietnam conflict refers to the period beginning February 28, 1961... proclaimed the date of May 7, 1975, to be the ending date of the “Vietnam era” (Presidential Proclamation No...

45 CFR 506.10 - “Vietnam conflict” defined.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 45 Public Welfare 3 2011-10-01 2011-10-01 false âVietnam conflictâ defined. 506.10 Section 506.10... § 506.10 “Vietnam conflict” defined. Vietnam conflict refers to the period beginning February 28, 1961... proclaimed the date of May 7, 1975, to be the ending date of the “Vietnam era” (Presidential Proclamation No...

Definition of an Acceptable Glass composition Region (AGCR) via an Index System and a Partitioning Function

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peeler, D. K.; Taylor, A. S.; Edwards, T.B.

2005-06-26

The objective of this investigation was to appeal to the available ComPro{trademark} database of glass compositions and measured PCTs that have been generated in the study of High Level Waste (HLW)/Low Activity Waste (LAW) glasses to define an Acceptable Glass Composition Region (AGCR). The term AGCR refers to a glass composition region in which the durability response (as defined by the Product Consistency Test (PCT)) is less than some pre-defined, acceptable value that satisfies the Waste Acceptance Product Specifications (WAPS)--a value of 10 g/L was selected for this study. To assess the effectiveness of a specific classification or index systemmore » to differentiate between acceptable and unacceptable glasses, two types of errors (Type I and Type II errors) were monitored. A Type I error reflects that a glass with an acceptable durability response (i.e., a measured NL [B] < 10 g/L) is classified as unacceptable by the system of composition-based constraints. A Type II error occurs when a glass with an unacceptable durability response is classified as acceptable by the system of constraints. Over the course of the efforts to meet this objective, two approaches were assessed. The first (referred to as the ''Index System'') was based on the use of an evolving system of compositional constraints which were used to explore the possibility of defining an AGCR. This approach was primarily based on ''glass science'' insight to establish the compositional constraints. Assessments of the Brewer and Taylor Index Systems did not result in the definition of an AGCR. Although the Taylor Index System minimized Type I errors which allowed access to composition regions of interest to improve melt rate or increase waste loadings for DWPF as compared to the current durability model, Type II errors were also committed. In the context of the application of a particular classification system in the process control system, Type II errors are much more serious than Type I errors. A Type I error only reflects that the particular constraint system being used is overly conservative (i.e., its application restricts access to glasses that have an acceptable measured durability response). A Type II error results in a more serious misclassification that could result in allowing the transfer of a Slurry Mix Evaporator (SME) batch to the melter, which is predicted to produce a durable product based on the specific system applied but in reality does not meet the defined ''acceptability'' criteria. More specifically, a nondurable product could be produced in DWPF. Given the presence of Type II errors, the Index System approach was deemed inadequate for further implementation consideration at the DWPF. The second approach (the JMP partitioning process) was purely data driven and empirically derived--glass science was not a factor. In this approach, the collection of composition--durability data in ComPro was sequentially partitioned or split based on the best available specific criteria and variables. More specifically, the JMP software chose the oxide (Al{sub 2}O{sub 3} for this dataset) that most effectively partitions the PCT responses (NL [B]'s)--perhaps not 100% effective based on a single oxide. Based on this initial split, a second request was made to split a particular set of the ''Y'' values (good or bad PCTs based on the 10 g/L limit) based on the next most critical ''X'' variable. This ''splitting'' or ''partitioning'' process was repeated until an AGCR was defined based on the use of only 3 oxides (Al{sub 2}O{sub 3}, CaO, and MgO) and critical values of > 3.75 wt% Al{sub 2}O{sub 3}, {ge} 0.616 wt% CaO, and < 3.521 wt% MgO. Using this set of criteria, the ComPro database was partitioned in which no Type II errors were committed. The automated partitioning function screened or removed 978 of the 2406 ComPro glasses which did cause some initial concerns regarding excessive conservatism regardless of its ability to identify an AGCR. However, a preliminary review of glasses within the 1428 ''acceptable'' glasses defining the ACGR includes glass systems of interest to support the accelerated mission.« less

Satellite Power Systems (SPS) concept definition study. Volume 2, part 2: System engineering. [cost and programmatics

NASA Technical Reports Server (NTRS)

Hanley, G. M.

1980-01-01

The latest technical and programmatic developments are considered as well as expansions of the Rockwell SPS cost model covering each phase of the program through the year 2030. Comparative cost/economic analyses cover elements of the satellite, construction system, space transportation vehicles and operations, and the ground receiving station. System plans to define time phased costs and planning requirements that support major milestones through the year 2000. A special analysis is included on natural resources required to build the SPS reference configuration. An appendix contains the SPS Work Breakdown Structure and dictionary along with detail cost data sheet on each system and main element of the program. Over 200 line items address DDT&E, theoretical first unit, investment cost per satellite, and operations charges for replacement capital and normal operations and maintenance costs.

Single payers, multiple systems: the scope and limits of subnational variation under a Federal health policy framework.

PubMed

Tuohy, Carolyn Hughes

2009-08-01

In political discourse, the term "single-payer system" originated in an attempt to stake out a middle ground between the public and private sectors in providing universal access to health care. In this view, a single-payer system is one in which health care is financed by government and delivered by privately owned and operated health care providers. The term appears to have been coined in U.S. policy debates to provide a rhetorical reference point for universal health insurance other than the "socialized medicine" of state-owned and -operated health care providers. This article, like others in this special issue, is meant to provide a more nuanced view of single-payer systems. In particular, it reviews experience in the prototypical single-payer system for physician and hospital services: the Canadian case. Given Canada's federal governance structure, this example also aptly illuminates the scope and limits of subnational variation within this single model of health care finance. And what it demonstrates in essence is that the very feature that defines the single-payer prototype -- the maintenance of independent providers remunerated by a single public payer in each province -- also leads to a set of profession-state bargains that define the limits of variation.

Beyond the rhetoric: what do we mean by a 'model of care'?

PubMed

Davidson, Patricia; Halcomb, Elizabeth; Hickman, L; Phillips, J; Graham, B

2006-01-01

Contemporary health care systems are constantly challenged to revise traditional methods of health care delivery. These challenges are multifaceted and stem from: (1) novel pharmacological and non-pharmacological treatments; (2) changes in consumer demands and expectations; (3) fiscal and resource constraints; (4) changes in societal demographics in particular the ageing of society; (5) an increasing burden of chronic disease; (6) documentation of limitations in traditional health care delivery; (7) increased emphasis on transparency, accountability, evidence-based practice (EBP) and clinical governance structures; and (8) the increasing cultural diversity of the community. These challenges provoke discussion of potential alternative models of care, with scant reference to defining what constitutes a model of care. This paper aims to define what is meant by the term 'model of care' and document the pragmatic systems and processes necessary to develop, plan, implement and evaluate novel models of care delivery. Searches of electronic databases, the reference lists of published materials, policy documents and the Internet were conducted using key words including 'model*', 'framework*', 'models, theoretical' and 'nursing models, theoretical'. The collated material was then analysed and synthesised into this review. This review determined that in addition to key conceptual and theoretical perspectives, quality improvement theory (eg. collaborative methodology), project management methods and change management theory inform both pragmatic and conceptual elements of a model of care. Crucial elements in changing health care delivery through the development of innovative models of care include the planning, development, implementation, evaluation and assessment of the sustainability of the new model. Regardless of whether change in health care delivery is attempted on a micro basis (eg. ward level) or macro basis (eg. national or state system) in order to achieve sustainable, effective and efficient changes a well-planned, systematic process is essential.

Assessing the accuracy of TDR-based water leak detection system

NASA Astrophysics Data System (ADS)

Fatemi Aghda, S. M.; GanjaliPour, K.; Nabiollahi, K.

2018-03-01

The use of TDR system to detect leakage locations in underground pipes has been developed in recent years. In this system, a bi-wire is installed in parallel with the underground pipes and is considered as a TDR sensor. This approach greatly covers the limitations arisen with using the traditional method of acoustic leak positioning. TDR based leak detection method is relatively accurate when the TDR sensor is in contact with water in just one point. Researchers have been working to improve the accuracy of this method in recent years. In this study, the ability of TDR method was evaluated in terms of the appearance of multi leakage points simultaneously. For this purpose, several laboratory tests were conducted. In these tests in order to simulate leakage points, the TDR sensor was put in contact with water at some points, then the number and the dimension of the simulated leakage points were gradually increased. The results showed that with the increase in the number and dimension of the leakage points, the error rate of the TDR-based water leak detection system increases. The authors tried, according to the results obtained from the laboratory tests, to develop a method to improve the accuracy of the TDR-based leak detection systems. To do that, they defined a few reference points on the TDR sensor. These points were created via increasing the distance between two conductors of TDR sensor and were easily identifiable in the TDR waveform. The tests were repeated again using the TDR sensor having reference points. In order to calculate the exact distance of the leakage point, the authors developed an equation in accordance to the reference points. A comparison between the results obtained from both tests (with and without reference points) showed that using the method and equation developed by the authors can significantly improve the accuracy of positioning the leakage points.

Population-Based Pediatric Reference Intervals in General Clinical Chemistry: A Swedish Survey.

PubMed

Ridefelt, Peter

2015-01-01

Very few high quality studies on pediatric reference intervals for general clinical chemistry and hematology analytes have been performed. Three recent prospective community-based projects utilising blood samples from healthy children in Sweden, Denmark and Canada have substantially improved the situation. The Swedish survey included 701 healthy children. Reference intervals for general clinical chemistry and hematology were defined.

Promoting A-Priori Interoperability of HLA-Based Simulations in the Space Domain: The SISO Space Reference FOM Initiative

NASA Technical Reports Server (NTRS)

Moller, Bjorn; Garro, Alfredo; Falcone, Alberto; Crues, Edwin Z.; Dexter, Daniel E.

2016-01-01

Distributed and Real-Time Simulation plays a key-role in the Space domain being exploited for missions and systems analysis and engineering as well as for crew training and operational support. One of the most popular standards is the 1516-2010 IEEE Standard for Modeling and Simulation (M&S) High Level Architecture (HLA). HLA supports the implementation of distributed simulations (called Federations) in which a set of simulation entities (called Federates) can interact using a Run-Time Infrastructure (RTI). In a given Federation, a Federate can publish and/or subscribes objects and interactions on the RTI only in accordance with their structures as defined in a FOM (Federation Object Model). Currently, the Space domain is characterized by a set of incompatible FOMs that, although meet the specific needs of different organizations and projects, increases the long-term cost for interoperability. In this context, the availability of a reference FOM for the Space domain will enable the development of interoperable HLA-based simulators for related joint projects and collaborations among worldwide organizations involved in the Space domain (e.g. NASA, ESA, Roscosmos, and JAXA). The paper presents a first set of results achieved by a SISO standardization effort that aims at providing a Space Reference FOM for international collaboration on Space systems simulations.

Fibrinolysis standards: a review of the current status.

PubMed

Thelwell, C

2010-07-01

Biological standards are used to calibrate measurements of components of the fibrinolytic system, either for assigning potency values to therapeutic products, or to determine levels in human plasma as an indicator of thrombotic risk. Traditionally WHO International Standards are calibrated in International Units based on consensus values from collaborative studies. The International Unit is defined by the response activity of a given amount of the standard in a bioassay, independent of the method used. Assay validity is based on the assumption that both standard and test preparation contain the same analyte, and the response in an assay is a true function of this analyte. This principle is reflected in the diversity of source materials used to prepare fibrinolysis standards, which has depended on the contemporary preparations they were employed to measure. With advancing recombinant technology, and improved analytical techniques, a reference system based on reference materials and associated reference methods has been recommended for future fibrinolysis standards. Careful consideration and scientific judgement must however be applied when deciding on an approach to develop a new standard, with decisions based on the suitability of a standard to serve its purpose, and not just to satisfy a metrological ideal. 2010 The International Association for Biologicals. Published by Elsevier Ltd. All rights reserved.

The role of internal reference prices in consumers' willingness to pay judgments: Thaler's Beer Pricing Task revisited.

PubMed

Ranyard, R; Charlton, J P; Williamson, J

2001-02-01

Alternative reference prices, either displayed in the environment (external) or recalled from memory (internal) are known to influence consumer judgments and decisions. In one line of previous research, internal reference prices have been defined in terms of general price expectations. However, Thaler (Marketing Science 4 (1985) 199; Journal of Behavioral Decision Making 12 (1999) 183) defined them as fair prices expected from specific types of seller. Using a Beer Pricing Task, he found that seller context had a substantial effect on willingness to pay, and concluded that this was due to specific internal reference prices evoked by specific contexts. In a think aloud study using the same task (N = 48), we found only a marginal effect of seller context. In a second study using the Beer Pricing Task and seven analogous ones (N = 144), general internal reference prices were estimated by asking people what they normally paid for various commodities. Both general internal reference prices and seller context influenced willingness to pay, although the effect of the latter was again rather small. We conclude that general internal reference prices have a greater impact in these scenarios than specific ones, because of the lower cognitive load involved in their storage and retrieval.

Application of new type of distributed multimedia databases to networked electronic museum

NASA Astrophysics Data System (ADS)

Kuroda, Kazuhide; Komatsu, Naohisa; Komiya, Kazumi; Ikeda, Hiroaki

1999-01-01

Recently, various kinds of multimedia application systems have actively been developed based on the achievement of advanced high sped communication networks, computer processing technologies, and digital contents-handling technologies. Under this background, this paper proposed a new distributed multimedia database system which can effectively perform a new function of cooperative retrieval among distributed databases. The proposed system introduces a new concept of 'Retrieval manager' which functions as an intelligent controller so that the user can recognize a set of distributed databases as one logical database. The logical database dynamically generates and performs a preferred combination of retrieving parameters on the basis of both directory data and the system environment. Moreover, a concept of 'domain' is defined in the system as a managing unit of retrieval. The retrieval can effectively be performed by cooperation of processing among multiple domains. Communication language and protocols are also defined in the system. These are used in every action for communications in the system. A language interpreter in each machine translates a communication language into an internal language used in each machine. Using the language interpreter, internal processing, such internal modules as DBMS and user interface modules can freely be selected. A concept of 'content-set' is also introduced. A content-set is defined as a package of contents. Contents in the content-set are related to each other. The system handles a content-set as one object. The user terminal can effectively control the displaying of retrieved contents, referring to data indicating the relation of the contents in the content- set. In order to verify the function of the proposed system, a networked electronic museum was experimentally built. The results of this experiment indicate that the proposed system can effectively retrieve the objective contents under the control to a number of distributed domains. The result also indicate that the system can effectively work even if the system becomes large.

NASA Docking System (NDS) Interface Definitions Document (IDD). Revision C, Nov. 2010

NASA Technical Reports Server (NTRS)

2010-01-01

The NASA Docking System (NDS) mating system supports low approach velocity docking and provides a modular and reconfigurable standard interface, supporting crewed and autonomous vehicles during mating and assembly operations. The NDS is NASA's implementation for the emerging International Docking System Standard (IDSS) using low impact docking technology. All NDS configurations can mate with the configuration specified in the IDSS Interface Definition Document (IDD) released September 21, 2010. The NDS evolved from the Low Impact Docking System (LIDS). The acronym international Low Impact Docking System (iLIDS) is also used to describe this system. NDS and iLIDS may be used interchangeability. Some of the heritage documentation and implementations (e.g., software command names) used on NDS will continue to use the LIDS acronym. The NDS IDD defines the interface characteristics and performance capability of the NDS, including uses ranging from crewed to autonomous space vehicles and from low earth orbit to deep space exploration. The responsibility for developing space vehicles and for making them technically and operationally compatible with the NDS rests with the vehicle providers. Host vehicle examples include crewed/uncrewed spacecraft, space station modules, elements, etc. Within this document, any docking space vehicle will be referred to as the host vehicle. This document defines the NDS-to-NDS interfaces, as well as the NDS-to-host vehicle interfaces and performance capability.

Reference intervals for serum osteocalcin concentrations in adult men and women from the study of health in Pomerania.

PubMed

Hannemann, Anke; Friedrich, Nele; Spielhagen, Christin; Rettig, Rainer; Ittermann, Till; Nauck, Matthias; Wallaschofski, Henri

2013-03-13

Osteocalcin (OC) is a bone-specific protein produced primarily by osteoblasts during bone formation. Besides its role in bone formation, osteocalcin may play a role in the regulation of energy metabolism and male fertility. To interpret serum OC data, reference intervals adapted to a specific laboratory method are needed. A healthy reference population was selected from the first follow-up of the Study of Health in Pomerania. Serum OC concentrations were measured with the IDS-iSYS N-Mid Osteocalcin assay on the IDS-iSYS Automated System (Immunodiagnostic Systems, Frankfurt am Main, Germany). The reference interval was defined as the central 95% range (2.5th-97.5th percentile). Age-specific reference intervals were calculated by quantile regression for 1107 men (25-79 years) and 545 premenopausal women (25-54 years). The reference interval for 498 postmenopausal women (50-79 years) was calculated irrespective of age. Median (1st-3rd quartile) serum OC concentrations were 15.4 ng/mL (12.0-19.4 ng/mL) in men, 14.4 ng/mL (11.3-18.5 ng/mL) in premenopausal women, and 18.6 ng/mL (13.6-25.6 ng/mL) in postmenopausal women. Serum OC concentrations were highest in men and premenopausal women aged 25-29 years, were stable during midlife, and rose again after 65 years of age in men and at transition to menopause in women. Serum OC concentrations were lower in women taking oral contraceptives or who were under hormone replacement therapy after menopause and in subjects with diabetes mellitus or with body mass index < 18 or > 30 kg/m2 than in subjects without these conditions. We established sex-specific adult reference intervals for the serum OC concentration measured by the IDS-iSYS N-Mid Osteocalcin assay.

A veterinary anatomy tutoring system.

PubMed

Theodoropoulos, G; Loumos, V; Antonopoulos, J

1994-02-14

A veterinary anatomy tutoring system was developed by using Knowledge Pro, an object-oriented software development tool with hypermedia capabilities, and MS Access, a relational database. Communication between them is facilitated by using the Structured Query Language (SQL). The architecture of the system is based on knowledge sets, each of which covers four different descriptions of an organ, namely gross anatomy (general description), gross anatomy (comparative features), histology, and embryology, which constitute the knowledge units. These knowledge units are linked with three global variables that define the animals, the topographies, and the system to which this organ belongs, creating three data-bases. These three data-bases are interrelated through the organ field in order to establish a relational model. This system allows versatility in the student's navigation through the information space by offering different modes for information location and presentation. These include course mode, review mode, reference mode, dissection mode, and comparison mode. In addition, the system provides a self-evaluation mode.

How the Government Defines "Rural" Has Implications for Education Policies and Practices. Issues & Answers. REL 2007-010

ERIC Educational Resources Information Center

Arnold, Michael L.; Biscoe, Belinda; Farmer, Thomas W.; Robertson, Dylan L.; Shapley, Kathy L.

2007-01-01

Clearly defining what rural means has tangible implications for public policies and practices in education, from establishing resource needs to achieving the goals of No Child Left Behind in rural areas. The word "rural" has many meanings. It has been defined in reference to population density, geographic features, and level of economic…

CPSGrader: Auto-Grading and Feedback Generation for Cyber-Physical Systems Education

DTIC Science & Technology

2014-12-21

to refer to ⋃ C∈C+ Ω(C,Γ(p)) (and⋃ C∈C− Ω(C,Γ(p))). The rationale behind this choice of ρ is two-fold: 1. To increase coverage of fault detection ... fault mentioned in Section 2.3. The purpose of the test is to detect that at some time instant t0, the robot bumps into the obstacle, then turns about...sampling. 5.6 Investigating Unknown Faults Using Clustering CPSGrader works with a fixed pre-defined library of faults and associated test benches

Optical testing of aspheres based on photochromic computer-generated holograms

NASA Astrophysics Data System (ADS)

Pariani, Giorgio; Bianco, Andrea; Bertarelli, Chiara; Spanó, Paolo; Molinari, Emilio

2010-07-01

Aspherical optics are widely used in modern optical telescopes and instrumentation because of their ability to reduce aberrations with a simple optical system. Testing their optical quality through null interferometry is not trivial as reference optics are not available. Computer-Generated Holograms (CGHs) are efficient devices that allow to generate a well-defined optical wavefront. We developed rewritable Computer Generated Holograms for the interferometric test of aspheres based on photochromic layers. These photochromic holograms are cost-effective and the method of production does not need any post exposure process.

The Recruitment, Education, and Training of PLA Navy Personnel (China Maritime Study, Number 12)

DTIC Science & Technology

2014-08-01

as to “cultivate,” “ nurture ,” “foster,” “train,” “develop,” or “educate.”9 It is defined in this context as the process by which cadets master the...individuals with criminal records or who are otherwise barred from service and subjecting the remaining candidates to physical, political, and psy...That all recruits continue to be referred to as conscripts demonstrates the oxymoronic nature of the system and suggests a reluctance to aban- don it

Flexible Method for Inter-object Communication in C++

NASA Technical Reports Server (NTRS)

Curlett, Brian P.; Gould, Jack J.

1994-01-01

A method has been developed for organizing and sharing large amounts of information between objects in C++ code. This method uses a set of object classes to define variables and group them into tables. The variable tables presented here provide a convenient way of defining and cataloging data, as well as a user-friendly input/output system, a standardized set of access functions, mechanisms for ensuring data integrity, methods for interprocessor data transfer, and an interpretive language for programming relationships between parameters. The object-oriented nature of these variable tables enables the use of multiple data types, each with unique attributes and behavior. Because each variable provides its own access methods, redundant table lookup functions can be bypassed, thus decreasing access times while maintaining data integrity. In addition, a method for automatic reference counting was developed to manage memory safely.

Lie algebraic similarity transformed Hamiltonians for lattice model systems

NASA Astrophysics Data System (ADS)

Wahlen-Strothman, Jacob M.; Jiménez-Hoyos, Carlos A.; Henderson, Thomas M.; Scuseria, Gustavo E.

2015-01-01

We present a class of Lie algebraic similarity transformations generated by exponentials of two-body on-site Hermitian operators whose Hausdorff series can be summed exactly without truncation. The correlators are defined over the entire lattice and include the Gutzwiller factor ni ↑ni ↓ , and two-site products of density (ni ↑+ni ↓) and spin (ni ↑-ni ↓) operators. The resulting non-Hermitian many-body Hamiltonian can be solved in a biorthogonal mean-field approach with polynomial computational cost. The proposed similarity transformation generates locally weighted orbital transformations of the reference determinant. Although the energy of the model is unbound, projective equations in the spirit of coupled cluster theory lead to well-defined solutions. The theory is tested on the one- and two-dimensional repulsive Hubbard model where it yields accurate results for small and medium sized interaction strengths.

Ranking the whole MEDLINE database according to a large training set using text indexing.

PubMed

Suomela, Brian P; Andrade, Miguel A

2005-03-24

The MEDLINE database contains over 12 million references to scientific literature, with about 3/4 of recent articles including an abstract of the publication. Retrieval of entries using queries with keywords is useful for human users that need to obtain small selections. However, particular analyses of the literature or database developments may need the complete ranking of all the references in the MEDLINE database as to their relevance to a topic of interest. This report describes a method that does this ranking using the differences in word content between MEDLINE entries related to a topic and the whole of MEDLINE, in a computational time appropriate for an article search query engine. We tested the capabilities of our system to retrieve MEDLINE references which are relevant to the subject of stem cells. We took advantage of the existing annotation of references with terms from the MeSH hierarchical vocabulary (Medical Subject Headings, developed at the National Library of Medicine). A training set of 81,416 references was constructed by selecting entries annotated with the MeSH term stem cells or some child in its sub tree. Frequencies of all nouns, verbs, and adjectives in the training set were computed and the ratios of word frequencies in the training set to those in the entire MEDLINE were used to score references. Self-consistency of the algorithm, benchmarked with a test set containing the training set and an equal number of references randomly selected from MEDLINE was better using nouns (79%) than adjectives (73%) or verbs (70%). The evaluation of the system with 6,923 references not used for training, containing 204 articles relevant to stem cells according to a human expert, indicated a recall of 65% for a precision of 65%. This strategy appears to be useful for predicting the relevance of MEDLINE references to a given concept. The method is simple and can be used with any user-defined training set. Choice of the part of speech of the words used for classification has important effects on performance. Lists of words, scripts, and additional information are available from the web address http://www.ogic.ca/projects/ks2004/.

Biomarker Reference Sets for Cancers in Women — EDRN Public Portal

Cancer.gov

The purpose of this study is to develop a standard reference set of specimens for use by investigators participating in the National Cancer Institutes Early Detection Research Network (EDRN) in defining false positive rates for new cancer biomarkers in women.

Estimating the Geocenter from GNSS Observations

NASA Astrophysics Data System (ADS)

Dach, Rolf; Michael, Meindl; Beutler, Gerhard; Schaer, Stefan; Lutz, Simon; Jäggi, Adrian

2014-05-01

The satellites of the Global Navigation Satellite Systems (GNSS) are orbiting the Earth according to the laws of celestial mechanics. As a consequence, the satellites are sensitive to the coordinates of the center of mass of the Earth. The coordinates of the (ground) tracking stations are referring to the center of figure as the conventional origin of the reference frame. The difference between the center of mass and center of figure is the instantaneous geocenter. Following this definition the global GNSS solutions are sensitive to the geocenter. Several studies demonstrated strong correlations of the GNSS-derived geocenter coordinates with parameters intended to absorb radiation pressure effects acting on the GNSS satellites, and with GNSS satellite clock parameters. One should thus pose the question to what extent these satellite-related parameters absorb (or hide) the geocenter information. A clean simulation study has been performed to answer this question. The simulation environment allows it in particular to introduce user-defined shifts of the geocenter (systematic inconsistencies between the satellite's and station's reference frames). These geocenter shifts may be recovered by the mentioned parameters - provided they were set up in the analysis. If the geocenter coordinates are not estimated, one may find out which other parameters absorb the user-defined shifts of the geocenter and to what extent. Furthermore, the simulation environment also allows it to extract the correlation matrix from the a posteriori covariance matrix to study the correlations between different parameter types of the GNSS analysis system. Our results show high degrees of correlations between geocenter coordinates, orbit-related parameters, and satellite clock parameters. These correlations are of the same order of magnitude as the correlations between station heights, troposphere, and receiver clock parameters in each regional or global GNSS network analysis. If such correlations are accepted in a GNSS analysis when estimating station coordinates, geocenter coordinates must be considered as mathematically estimable in a global GNSS analysis. The geophysical interpretation may of course become difficult, e.g., if insufficient orbit models are used.

National Standard of the Russian Federation for Space Debris Mitigation

NASA Astrophysics Data System (ADS)

Loginov, S.; Yakovlev, M.; Mikhailov, M.; Popkova, L.

2009-03-01

Normative and technical document that define requirements for the mitigation of human-produced near-earth space pollution develops in Russian Federation.NATIONAL STANDARD of the Russian Federation GOST R 52925-2008 «SPACE TECHNOLOGY ITEMS. General Requirements on Space Systems for the Mitigation of Human-Produced near-Earth Space Pollution» was approved in 2008 and entered into force since 1st January of 2009. Requirements of this standard harmonized with requirements of «UN SPACE DEBRIS MITIGATION GUIDELINESÈ»This standard consists of six parts:- Scope;- References to Standards;- Terms & Definitions;- Abbreviations;- General Provisions;- General Requirements on Space Systems for the Mitigation of Human-Produced near-Earth Space Pollution.

Novel Software for Performing Leksell Stereotactic Surgery without the Use of Printing Films: Technical Note.

PubMed

Hashizume, Akira; Akimitsu, Tomohide; Iida, Koji; Kagawa, Kota; Katagiri, Masaya; Hanaya, Ryosuke; Arita, Kazunori; Kurisu, Kaoru

2016-01-01

Hospitals in Japan have recently begun to employ the DICOM viewer system on desktop or laptop monitors. However, conventional embedding surgery for deep-brain stimulation with the Leksell stereotactic system (LSS) requires printed X-ray films for defining the coordination, coregistration of actual surgical films with the reference coordinates, and validation of the needle trajectories. While just performing these procedures on desktop or laptop monitors, the authors were able to develop novel software to facilitate complete digital manipulation with the Leksell frame without printing films. In this study, we validated the practical use of LSS, and benefit of this software in the Takanobashi Central Hospital and Kagoshima University Hospital.

Fabrication and Testing of Binary-Phase Fourier Gratings for Nonuniform Array Generation

NASA Technical Reports Server (NTRS)

Keys, Andrew S.; Crow, Robert W.; Ashley, Paul R.; Nelson, Tom R., Jr.; Parker, Jack H.; Beecher, Elizabeth A.

2004-01-01

This effort describes the fabrication and testing of binary-phase Fourier gratings designed to generate an incoherent array of output source points with nonuniform user-defined intensities, symmetric about the zeroth order. Like Dammann fanout gratings, these binary-phase Fourier gratings employ only two phase levels to generate a defined output array. Unlike Dammann fanout gratings, these gratings generate an array of nonuniform, user-defined intensities when projected into the far-field regime. The paper describes the process of design, fabrication, and testing for two different version of the binary-phase grating; one designed for a 12 micron wavelength, referred to as the Long-Wavelength Infrared (LWIR) grating, and one designed for a 5 micron wavelength, referred to as the Mid-Wavelength Infrared Grating (MWIR).

Valid analytical performance specifications for combined analytical bias and imprecision for the use of common reference intervals.

PubMed

Hyltoft Petersen, Per; Lund, Flemming; Fraser, Callum G; Sandberg, Sverre; Sölétormos, György

2018-01-01

Background Many clinical decisions are based on comparison of patient results with reference intervals. Therefore, an estimation of the analytical performance specifications for the quality that would be required to allow sharing common reference intervals is needed. The International Federation of Clinical Chemistry (IFCC) recommended a minimum of 120 reference individuals to establish reference intervals. This number implies a certain level of quality, which could then be used for defining analytical performance specifications as the maximum combination of analytical bias and imprecision required for sharing common reference intervals, the aim of this investigation. Methods Two methods were investigated for defining the maximum combination of analytical bias and imprecision that would give the same quality of common reference intervals as the IFCC recommendation. Method 1 is based on a formula for the combination of analytical bias and imprecision and Method 2 is based on the Microsoft Excel formula NORMINV including the fractional probability of reference individuals outside each limit and the Gaussian variables of mean and standard deviation. The combinations of normalized bias and imprecision are illustrated for both methods. The formulae are identical for Gaussian and log-Gaussian distributions. Results Method 2 gives the correct results with a constant percentage of 4.4% for all combinations of bias and imprecision. Conclusion The Microsoft Excel formula NORMINV is useful for the estimation of analytical performance specifications for both Gaussian and log-Gaussian distributions of reference intervals.

The subject-fixated coaxially sighted corneal light reflex: a clinical marker for centration of refractive treatments and devices.

PubMed

Chang, Daniel H; Waring, George O

2014-11-01

To describe the inconsistencies in definition, application, and usage of the ocular reference axes (optical axis, visual axis, line of sight, pupillary axis, and topographic axis) and angles (angle kappa, lambda, and alpha) and to propose a precise, reproducible, clinically defined reference marker and axis for centration of refractive treatments and devices. Perspective. Literature review of papers dealing with ocular reference axes, angles, and centration. The inconsistent definitions and usage of the current ocular axes, as derived from eye models, limit their clinical utility. With a clear understanding of Purkinje images and a defined alignment of the observer, light source/fixation target, and subject eye, the subject-fixated coaxially sighted corneal light reflex can be a clinically useful reference marker. The axis formed by connecting the subject-fixated coaxially sighted corneal light reflex and the fixation point, the subject-fixated coaxially sighted corneal light reflex axis, is independent of pupillary dilation and phakic status of the eye. The relationship of the subject-fixated coaxially sighted corneal light reflex axis to a refined definition of the visual axis without reference to nodal points, the foveal-fixation axis, is discussed. The displacement between the subject-fixated coaxially sighted corneal light reflex and pupil center is described not by an angle, but by a chord, here termed chord mu. The application of the subject-fixated coaxially sighted corneal light reflex to the surgical centration of refractive treatments and devices is discussed. As a clinically defined reference marker, the subject-fixated coaxially sighted corneal light reflex avoids the shortcomings of current ocular axes for clinical application and may contribute to better consensus in the literature and improved patient outcomes. Copyright © 2014 Elsevier Inc. All rights reserved.

Deep brain stimulation for Parkinson's disease: defining the optimal location within the subthalamic nucleus.

PubMed

Bot, Maarten; Schuurman, P Richard; Odekerken, Vincent J J; Verhagen, Rens; Contarino, Fiorella Maria; De Bie, Rob M A; van den Munckhof, Pepijn

2018-05-01

Individual motor improvement after deep brain stimulation (DBS) of the subthalamic nucleus (STN) for Parkinson's disease (PD) varies considerably. Stereotactic targeting of the dorsolateral sensorimotor part of the STN is considered paramount for maximising effectiveness, but studies employing the midcommissural point (MCP) as anatomical reference failed to show correlation between DBS location and motor improvement. The medial border of the STN as reference may provide better insight in the relationship between DBS location and clinical outcome. Motor improvement after 12 months of 65 STN DBS electrodes was categorised into non-responding, responding and optimally responding body-sides. Stereotactic coordinates of optimal electrode contacts relative to both medial STN border and MCP served to define theoretic DBS 'hotspots'. Using the medial STN border as reference, significant negative correlation (Pearson's correlation -0.52, P<0.01) was found between the Euclidean distance from the centre of stimulation to this DBS hotspot and motor improvement. This hotspot was located at 2.8 mm lateral, 1.7 mm anterior and 2.5 mm superior relative to the medial STN border. Using MCP as reference, no correlation was found. The medial STN border proved superior compared with MCP as anatomical reference for correlation of DBS location and motor improvement, and enabled defining an optimal DBS location within the nucleus. We therefore propose the medial STN border as a better individual reference point than the currently used MCP on preoperative stereotactic imaging, in order to obtain optimal and thus less variable motor improvement for individual patients with PD following STN DBS. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Estimating the Critical Point of Crowding in the Emergency Department for the Warning System

NASA Astrophysics Data System (ADS)

Chang, Y.; Pan, C.; Tseng, C.; Wen, J.

2011-12-01

The purpose of this study is to deduce a function from the admissions/discharge rate of patient flow to estimate a "Critical Point" that provides a reference for warning systems in regards to crowding in the emergency department (ED) of a hospital or medical clinic. In this study, a model of "Input-Throughput-Output" was used in our established mathematical function to evaluate the critical point. The function is defined as dPin/dt=dwait/dt+Cp×B+ dPout/dt where Pin= number of registered patients, Pwait= number of waiting patients, Cp= retention rate per bed (calculated for the critical point), B= number of licensed beds in the treatment area, and Pout= number of patients discharged from the treatment area. Using the average Cp of ED crowding, we could start the warning system at an appropriate time and then plan for necessary emergency response to facilitate the patient process more smoothly. It was concluded that ED crowding could be quantified using the average value of Cp and the value could be used as a reference for medical staff to give optimal emergency medical treatment to patients. Therefore, additional practical work should be launched to collect more precise quantitative data.

40 CFR 53.2 - General requirements for a reference method determination.

Code of Federal Regulations, 2011 CFR

2011-07-01

... part. Further, FRM samplers must be manufactured in an ISO 9001-registered facility, as defined in § 53... manufactured in an ISO 9001-registered facility, as defined in § 53.1 and as set forth in § 53.51. (b...

What Is Cyberspace?

ERIC Educational Resources Information Center

Bauwens, Michel

1994-01-01

Discusses the concept of cyberspace, defines three different levels that have been or will be attained, and compares it with mediaspace; examines the concept of virtualization, particularly the virtual library, and defines three different levels; and describes the concepts of cybrarians, cyberocracy, and cyberology. (Contains seven references.)…

CanOpen on RASTA: The Integration of the CanOpen IP Core in the Avionics Testbed

NASA Astrophysics Data System (ADS)

Furano, Gianluca; Guettache, Farid; Magistrati, Giorgio; Tiotto, Gabriele; Ortega, Carlos Urbina; Valverde, Alberto

2013-08-01

This paper presents the work done within the ESA Estec Data Systems Division, targeting the integration of the CanOpen IP Core with the existing Reference Architecture Test-bed for Avionics (RASTA). RASTA is the reference testbed system of the ESA Avionics Lab, designed to integrate the main elements of a typical Data Handling system. It aims at simulating a scenario where a Mission Control Center communicates with on-board computers and systems through a TM/TC link, thus providing the data management through qualified processors and interfaces such as Leon2 core processors, CAN bus controllers, MIL-STD-1553 and SpaceWire. This activity aims at the extension of the RASTA with two boards equipped with HurriCANe controller, acting as CANOpen slaves. CANOpen software modules have been ported on the RASTA system I/O boards equipped with Gaisler GR-CAN controller and acts as master communicating with the CCIPC boards. CanOpen serves as upper application layer for based on CAN defined within the CAN-in-Automation standard and can be regarded as the definitive standard for the implementation of CAN-based systems solutions. The development and integration of CCIPC performed by SITAEL S.p.A., is the first application that aims to bring the CANOpen standard for space applications. The definition of CANOpen within the European Cooperation for Space Standardization (ECSS) is under development.

Pathway to 2022: The Ongoing Modernization of the United States National Spatial Reference System

NASA Astrophysics Data System (ADS)

Stone, W. A.; Caccamise, D.

2017-12-01

The National Oceanic and Atmospheric Administration's National Geodetic Survey (NGS) mission is "to define, maintain and provide access to the National Spatial Reference System (NSRS) to meet our nation's economic, social, and environmental needs." The NSRS is an assemblage of geophysical and geodetic models, tools, and data, with the most-visible components being the North American Datum of 1983 (NAD83) and the North American Vertical Datum of 1988 (NAVD88), which together provide a consistent spatial reference framework for myriad geospatial applications and positioning requirements throughout the United States. The NGS is engaged in an ongoing and comprehensive multi-year project of modernizing the NSRS, a makeover necessitated by technological developments and user accuracy requirements, all with a goal of providing a modern, accurate, accessible, and globally aligned national positioning framework exploiting the substantial power and utility of the Global Navigation Satellite System - of both today and tomorrow. The modernized NSRS will include four new-generation geometric terrestrial reference frames (replacing NAD83) and a technically unprecedented geopotential datum (replacing NAVD88), all to be released in 2022 (anticipated). This poster/presentation will describe the justification for this modernization effort and will update the status and planned evolution of the NSRS as 2022 draws ever closer. Also discussed will be recent developments, including the publication of "blueprint" documents addressing technical details of various facets of the modernized NSRS and a continued series of public Geospatial Summits. Supporting/ancillary projects such as Gravity for the Redefinition of the American Vertical Datum (GRAV-D), which will result in the generation of a highly accurate gravimetric geoid - or definitional reference surface (zero elevation) - for the future geopotential datum, and Geoid Slope Validation Surveys (GSVS), which are exploring the achievable accuracy of the new geopotential datum, will be summarized. Also included will be suggestions of user preparation for transition to the NSRS of tomorrow.

The Global Geodetic Observing System: Space Geodesy Networks for the Future

NASA Technical Reports Server (NTRS)

Pearlman, Michael; Pavlis, Erricos; Ma, Chopo; Altamini, Zuheir; Noll, Carey; Stowers, David

2011-01-01

Ground-based networks of co-located space geodetic techniques (VLBI, SLR, GNSS. and DORIS) are the basis for the development and maintenance of the International Terrestrial Reference frame (ITRF), which is our metric of reference for measurements of global change, The Global Geodetic Observing System (GGOS) of the International Association of Geodesy (IAG) has established a task to develop a strategy to design, integrate and maintain the fundamental geodetic network and supporting infrastructure in a sustainable way to satisfy the long-term requirements for the reference frame. The GGOS goal is an origin definition at 1 mm or better and a temporal stability on the order of 0.1 mm/y, with similar numbers for the scale and orientation components. These goals are based on scientific requirements to address sea level rise with confidence, but other applications are not far behind. Recent studies including one by the US National Research Council has strongly stated the need and the urgency for the fundamental space geodesy network. Simulations are underway to examining accuracies for origin, scale and orientation of the resulting ITRF based on various network designs and system performance to determine the optimal global network to achieve this goal. To date these simulations indicate that 24 - 32 co-located stations are adequate to define the reference frame and a more dense GNSS and DORIS network will be required to distribute the reference frame to users anywhere on Earth. Stations in the new global network will require geologically stable sites with good weather, established infrastructure, and local support and personnel. GGOS wil seek groups that are interested in participation. GGOS intends to issues a Call for Participation of groups that would like to contribute in the network implementation and operation. Some examples of integrated stations currently in operation or under development will be presented. We will examine necessary conditions and challenges in designing a co-location station.

The high speed interconnect system architecture and operation

NASA Astrophysics Data System (ADS)

Anderson, Steven C.

The design and operation of a fiber-optic high-speed interconnect system (HSIS) being developed to meet the requirements of future avionics and flight-control hardware with distributed-system architectures are discussed. The HSIS is intended for 100-Mb/s operation of a local-area network with up to 256 stations. It comprises a bus transmission system (passive star couplers and linear media linked by active elements) and network interface units (NIUs). Each NIU is designed to perform the physical, data link, network, and transport functions defined by the ISO OSI Basic Reference Model (1982 and 1983) and incorporates a fiber-optic transceiver, a high-speed protocol based on the SAE AE-9B linear token-passing data bus (1986), and a specialized application interface unit. The operating modes and capabilities of HSIS are described in detail and illustrated with diagrams.

Remotely detected differential pulse transit time as a stress indicator

NASA Astrophysics Data System (ADS)

Kaur, Balvinder; Tarbox, Elizabeth; Cissel, Marty; Moses, Sophia; Luthra, Megha; Vaidya, Misha; Tran, Nhien; Ikonomidou, Vasiliki N.

2015-05-01

The human cardiovascular system, controlled by the autonomic nervous system (ANS), is one of the first sites where one can see the "fight-or-flight" response due to the presence of external stressors. In this paper, we investigate the possibility of detecting mental stress using a novel measure that can be measured in a contactless manner: Pulse transit time (dPTT), which refers to the time that is required for the blood wave (BW) to cover the distance from the heart to a defined remote location in the body. Loosely related to blood pressure, PTT is a measure of blood velocity, and is also implicated in the "fight-or-flight" response. We define the differential PTT (dPTT) as the difference in PTT between two remote areas of the body, such as the forehead and the palm. Expanding our previous work on remote BW detection from visible spectrum videos, we built a system that remotely measures dPTT. Human subject data were collected under an IRB approved protocol from 15 subjects both under normal and stress states and are used to initially establish the potential use of remote dPPT detection as a stress indicator.

NORTH PORTAL-HOT WATER CIRCULATION PUMP CALCULATION-SHOP BUILDING #5006

DOE Office of Scientific and Technical Information (OSTI.GOV)

R. Blackstone

1996-01-25

The purpose of this design analysis and calculation is to size a circulating pump for the service hot water system in the Shop Building 5006, in accordance with the Uniform Plumbing Code (Section 4.4.1) and U.S. Department of Energy Order 6430.1A-1540 (Section 4.4.2). The method used for the calculation is based on Reference 5.2. This consists of determining the total heat transfer from the service hot water system piping to the surrounding environment. The heat transfer is then used to define the total pumping capacity based on a given temperature change in the circulating hot water as it flows throughmore » the closed loop piping system. The total pumping capacity is used to select a pump model from manufacturer's literature. This established the head generation for that capacity and particular pump model. The total length of all hot water supply and return piping including fittings is then estimated from the plumbing drawings which defines the pipe friction losses that must fit within the available pump head. Several iterations may be required before a pump can be selected that satisfies the head-capacity requirements.« less

40 CFR 53.1 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... followed by a gravimetric mass determination, but which is not a Class I equivalent method because of... MONITORING REFERENCE AND EQUIVALENT METHODS General Provisions § 53.1 Definitions. Terms used but not defined... slope of a linear plot fitted to corresponding candidate and reference method mean measurement data...

Internal validation of the RapidHIT® ID system.

PubMed

Wiley, Rachel; Sage, Kelly; LaRue, Bobby; Budowle, Bruce

2017-11-01

Traditionally, forensic DNA analysis has required highly skilled forensic geneticists in a dedicated laboratory to generate short tandem repeat (STR) profiles. STR profiles are routinely used either to associate or exclude potential donors of forensic biological evidence. The typing of forensic reference samples has become more demanding, especially with the requirement in some jurisdictions to DNA profile arrestees. The Rapid DNA (RDNA) platform, the RapidHIT ® ID (IntegenX ® , Pleasanton, CA), is a fully automated system capable of processing reference samples in approximately 90min with minimal human intervention. Thus, the RapidHIT ID instrument can be deployed to non-laboratory environments (e.g., booking stations) and run by trained atypical personnel such as law enforcement. In order to implement the RapidHIT ID platform, validation studies are needed to define the performance and limitations of the system. Internal validation studies were undertaken with four early-production RapidHIT ID units. Reliable and concordant STR profiles were obtained from reference buccal swabs. Throughout the study, no contamination was observed. The overall first-pass success rate with an "expert-like system" was 72%, which is comparable to another current RDNA platform commercially available. The system's second-pass success rate (involving manual interpretation on first-pass inconclusive results) increased to 90%. Inhibitors (i.e., coffee, smoking tobacco, and chewing tobacco) did not appear to affect typing by the instrument system; however, substrate (i.e., swab type) did impact typing success. Additionally, one desirable feature not available with other Rapid systems is that in the event of a system failed run, a swab can be recovered and subsequently re-analyzed in a new sample cartridge. Therefore, rarely should additional sampling or swab consumption be necessary. The RapidHIT ID system is a robust and reliable tool capable of generating complete STR profiles within the forensic DNA typing laboratory or with proper training in decentralized environments by non-laboratory personnel. Copyright © 2017 Elsevier B.V. All rights reserved.

Suitability of different glycoproteins and test systems for detecting cross-reactive carbohydrate determinant-specific IgE in hymenoptera venom-allergic patients.

PubMed

Mertens, Melanie; Brehler, Randolf

2011-01-01

In hymenoptera venom allergy, about 75% of detected in vitro double positivity to yellow jacket and honeybee venom is ascribed to specific IgE (sIgE) directed against cross-reactive carbohydrate determinants (CCDs). To date, for the detection of CCD-sIgE, different carbohydrate antigens and methods are used. The most suitable one still has to be identified. Eighty-seven patients with confirmed hymenoptera venom allergy and venom sIgE values of ≥0.7 kU/l were investigated. Sixty-five patients showed sIgE reactivity to both yellow jacket and honeybee venom, 22 were venom mono positive and served as controls. Occurrence of CCD-sIgE was determined using bromelain, horseradish peroxidase (HRP) and MUXF(3) on system A, and ascorbic acid oxidase (AAO), bromelain and HRP on system B. Further, a reference standard for CCD-sIgE evaluation was created: CCD positivity was assumed when at least 4 of the 6 test results were positive. According to the defined reference standard, 45/65 venom double positive patients exhibited CCD-sIgE. Using system A, comparison with the reference standard revealed sensitivity and specificity values of 96 and 97%, respectively, for MUXF(3), 100 and 100%, respectively, for bromelain, and 96 and 97%, respectively, for HRP. Using system B, sensitivity and specificity was 98 and 97%, respectively, for AAO, 62 and 95%, respectively, for bromelain, and 96 and 69%, respectively, for HRP. Results of the 3 test allergens obtained with system A showed strong correlations (r = 0.932-0.976), whereas results with system B showed lower correlations (r = 0.714-0.898). All 3 test allergens used with system A are suitable for CCD-sIgE detection in hymenoptera venom allergy. With system B, only AAO seems to be a reliable tool. Copyright © 2011 S. Karger AG, Basel.

Multi-Component Molecular-Level Body Composition Reference Methods: Evolving Concepts and Future Directions

PubMed Central

Heymsfield, Steven B.; Ebbeling, Cara B.; Zheng, Jolene; Pietrobelli, Angelo; Strauss, Boyd J.; Silva, Analiza M.; Ludwig, David S.

2015-01-01

Excess adiposity is the main phenotypic feature that defines human obesity and that plays a pathophysiological role in most chronic diseases. Measuring the amount of fat mass present is thus a central aspect of studying obesity at the individual and population levels. Nevertheless, a consensus is lacking among investigators on a single accepted “reference” approach for quantifying fat mass in vivo. While the research community generally relies on the multicomponent body-volume class of “reference” models for quantifying fat mass, no definable guide discerns among different applied equations for partitioning the four (fat, water, protein, and mineral mass) or more quantified components, standardizes “adjustment” or measurement system approaches for model-required labeled water dilution volumes and bone mineral mass estimates, or firmly establishes the body temperature at which model physical properties are assumed. The resulting differing reference strategies for quantifying body composition in vivo leads to small but under some circumstances important differences in the amount of measured body fat. Recent technological advances highlight opportunities to expand model applications to new subject groups and measured components such as total body protein. The current report reviews the historical evolution of multicomponent body volume-based methods in the context of prevailing uncertainties and future potential. PMID:25645009

Biomass Scenario Model Documentation: Data and References

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lin, Y.; Newes, E.; Bush, B.

2013-05-01

The Biomass Scenario Model (BSM) is a system dynamics model that represents the entire biomass-to-biofuels supply chain, from feedstock to fuel use. The BSM is a complex model that has been used for extensive analyses; the model and its results can be better understood if input data used for initialization and calibration are well-characterized. It has been carefully validated and calibrated against the available data, with data gaps filled in using expert opinion and internally consistent assumed values. Most of the main data sources that feed into the model are recognized as baseline values by the industry. This report documentsmore » data sources and references in Version 2 of the BSM (BSM2), which only contains the ethanol pathway, although subsequent versions of the BSM contain multiple conversion pathways. The BSM2 contains over 12,000 total input values, with 506 distinct variables. Many of the variables are opportunities for the user to define scenarios, while others are simply used to initialize a stock, such as the initial number of biorefineries. However, around 35% of the distinct variables are defined by external sources, such as models or reports. The focus of this report is to provide insight into which sources are most influential in each area of the supply chain.« less

Three-Dimensional Modeling of Aircraft High-Lift Components with Vehicle Sketch Pad

NASA Technical Reports Server (NTRS)

Olson, Erik D.

2016-01-01

Vehicle Sketch Pad (OpenVSP) is a parametric geometry modeler that has been used extensively for conceptual design studies of aircraft, including studies using higher-order analysis. OpenVSP can model flap and slat surfaces using simple shearing of the airfoil coordinates, which is an appropriate level of complexity for lower-order aerodynamic analysis methods. For three-dimensional analysis, however, there is not a built-in method for defining the high-lift components in OpenVSP in a realistic manner, or for controlling their complex motions in a parametric manner that is intuitive to the designer. This paper seeks instead to utilize OpenVSP's existing capabilities, and establish a set of best practices for modeling high-lift components at a level of complexity suitable for higher-order analysis methods. Techniques are described for modeling the flap and slat components as separate three-dimensional surfaces, and for controlling their motion using simple parameters defined in the local hinge-axis frame of reference. To demonstrate the methodology, an OpenVSP model for the Energy-Efficient Transport (EET) AR12 wind-tunnel model has been created, taking advantage of OpenVSP's Advanced Parameter Linking capability to translate the motions of the high-lift components from the hinge-axis coordinate system to a set of transformations in OpenVSP's frame of reference.

Integrating nursing diagnostic concepts into the medical entities dictionary using the ISO Reference Terminology Model for Nursing Diagnosis.

PubMed

Hwang, Jee-In; Cimino, James J; Bakken, Suzanne

2003-01-01

The purposes of the study were (1) to evaluate the usefulness of the International Standards Organization (ISO) Reference Terminology Model for Nursing Diagnoses as a terminology model for defining nursing diagnostic concepts in the Medical Entities Dictionary (MED) and (2) to create the additional hierarchical structures required for integration of nursing diagnostic concepts into the MED. The authors dissected nursing diagnostic terms from two source terminologies (Home Health Care Classification and the Omaha System) into the semantic categories of the ISO model. Consistent with the ISO model, they selected Focus and Judgment as required semantic categories for creating intensional definitions of nursing diagnostic concepts in the MED. Because the MED does not include Focus and Judgment hierarchies, the authors developed them to define the nursing diagnostic concepts. The ISO model was sufficient for dissecting the source terminologies into atomic terms. The authors identified 162 unique focus concepts from the 266 nursing diagnosis terms for inclusion in the Focus hierarchy. For the Judgment hierarchy, the authors precoordinated Judgment and Potentiality instead of using Potentiality as a qualifier of Judgment as in the ISO model. Impairment and Alteration were the most frequently occurring judgments. Nursing care represents a large proportion of health care activities; thus, it is vital that terms used by nurses are integrated into concept-oriented terminologies that provide broad coverage for the domain of health care. This study supports the utility of the ISO Reference Terminology Model for Nursing Diagnoses as a facilitator for the integration process.

Integrating Nursing Diagnostic Concepts into the Medical Entities Dictionary Using the ISO Reference Terminology Model for Nursing Diagnosis

PubMed Central

Hwang, Jee-In; Cimino, James J.; Bakken, Suzanne

2003-01-01

Objective: The purposes of the study were (1) to evaluate the usefulness of the International Standards Organization (ISO) Reference Terminology Model for Nursing Diagnoses as a terminology model for defining nursing diagnostic concepts in the Medical Entities Dictionary (MED) and (2) to create the additional hierarchical structures required for integration of nursing diagnostic concepts into the MED. Design and Measurements: The authors dissected nursing diagnostic terms from two source terminologies (Home Health Care Classification and the Omaha System) into the semantic categories of the ISO model. Consistent with the ISO model, they selected Focus and Judgment as required semantic categories for creating intensional definitions of nursing diagnostic concepts in the MED. Because the MED does not include Focus and Judgment hierarchies, the authors developed them to define the nursing diagnostic concepts. Results: The ISO model was sufficient for dissecting the source terminologies into atomic terms. The authors identified 162 unique focus concepts from the 266 nursing diagnosis terms for inclusion in the Focus hierarchy. For the Judgment hierarchy, the authors precoordinated Judgment and Potentiality instead of using Potentiality as a qualifier of Judgment as in the ISO model. Impairment and Alteration were the most frequently occurring judgments. Conclusions: Nursing care represents a large proportion of health care activities; thus, it is vital that terms used by nurses are integrated into concept-oriented terminologies that provide broad coverage for the domain of health care. This study supports the utility of the ISO Reference Terminology Model for Nursing Diagnoses as a facilitator for the integration process. PMID:12668692

A synergistic method for vibration suppression of an elevator mechatronic system

NASA Astrophysics Data System (ADS)

Knezevic, Bojan Z.; Blanusa, Branko; Marcetic, Darko P.

2017-10-01

Modern elevators are complex mechatronic systems which have to satisfy high performance in precision, safety and ride comfort. Each elevator mechatronic system (EMS) contains a mechanical subsystem which is characterized by its resonant frequency. In order to achieve high performance of the whole system, the control part of the EMS inevitably excites resonant circuits causing the occurrence of vibration. This paper proposes a synergistic solution based on the jerk control and the upgrade of the speed controller with a band-stop filter to restore lost ride comfort and speed control caused by vibration. The band-stop filter eliminates the resonant component from the speed controller spectra and jerk control provides operating of the speed controller in a linear mode as well as increased ride comfort. The original method for band-stop filter tuning based on Goertzel algorithm and Kiefer search algorithm is proposed in this paper. In order to generate the speed reference trajectory which can be defined by different shapes and amplitudes of jerk, a unique generalized model is proposed. The proposed algorithm is integrated in the power drive control algorithm and implemented on the digital signal processor. Through experimental verifications on a scale down prototype of the EMS it has been verified that only synergistic effect of controlling jerk and filtrating the reference torque can completely eliminate vibrations.

Value-Based Assessment of Radiology Reporting Using Radiologist-Referring Physician Two-Way Feedback System-a Design Thinking-Based Approach.

PubMed

Shaikh, Faiq; Hendrata, Kenneth; Kolowitz, Brian; Awan, Omer; Shrestha, Rasu; Deible, Christopher

2017-06-01

In the era of value-based healthcare, many aspects of medical care are being measured and assessed to improve quality and reduce costs. Radiology adds enormously to health care costs and is under pressure to adopt a more efficient system that incorporates essential metrics to assess its value and impact on outcomes. Most current systems tie radiologists' incentives and evaluations to RVU-based productivity metrics and peer-review-based quality metrics. In a new potential model, a radiologist's performance will have to increasingly depend on a number of parameters that define "value," beginning with peer review metrics that include referrer satisfaction and feedback from radiologists to the referring physician that evaluates the potency and validity of clinical information provided for a given study. These new dimensions of value measurement will directly impact the cascade of further medical management. We share our continued experience with this project that had two components: RESP (Referrer Evaluation System Pilot) and FRACI (Feedback from Radiologist Addressing Confounding Issues), which were introduced to the clinical radiology workflow in order to capture referrer-based and radiologist-based feedback on radiology reporting. We also share our insight into the principles of design thinking as applied in its planning and execution.

Integrated Space Transportation Plan: Defining Technology Requirements and Next Generation Launch Systems to Meet Commercial and Government Needs. Revision 20 Oct. 1999

NASA Technical Reports Server (NTRS)

Davidoff, Larry D.; Reichert, Jack M.

1999-01-01

NASA continues to focus on improving safety and reliability while reducing the annual cost of meeting human space flight and unique ISS and exploration needs. NASA's Space Transportation Architecture Study (STAS) Phase 2 in early 1998 focused on space transportation options. Subsequently, NASA directed parallel industry and government teams to conduct the Integrated Space Transportation Plan effort (STAS Phase 3). The objective of ISTP was to develop technology requirements, roadmaps, and risk reduction portfolio that considered expanded definition of "clean-sheet" and Shuttle-derived second generation ETO transportation systems in support of a 2005 RLV competition for NASA missions beginning 2010. NASA provided top-level requirements for improvements in safety, reliability, and cost and a set of design reference missions representing NASA ISS, human exploration, commercial, and other civil and government needs. This paper addresses the challenges of meeting NASA's objectives while servicing the varied market segments represented in the ISTP design reference missions and provides a summary of technology development needs and candidate system concepts. A comparison of driving requirements, architectures and technology needs is discussed and descriptions of viable Shuttle-derived and next generation systems to meet the market needs are presented.

Witchcraft illness in the Evuzok nosological system.

PubMed

Guimera, L M

1978-12-01

The Evuzok nosological system is structured with respect to two frames of reference, one designating illness as an empirical reality (descriptive subsystem), the other designating it according to its religious, magical and social significance (etiological subsystem). The articulation of these two subsystems is brought about in the process of diagnosis. Having examined this system as a whole, the author devotes his attention to a particular set of etiological categories, those which associate illness with witchcraft (nocturnal illnesses). He attempts to define their distinctive traits and, from this, to determine their common elemental structure. This study, based on a number of years of fieldwork, is part of an ongoing research program on African folk-medicine pursued by the Laboratoire d'Ethnologie et de Sociologie Comparative of the Université de Paris X.

Fifth NASA Goddard Conference on Mass Storage Systems and Technologies.. Volume 1

NASA Technical Reports Server (NTRS)

Kobler, Benjamin (Editor); Hariharan, P. C. (Editor)

1996-01-01

This document contains copies of those technical papers received in time for publication prior to the Fifth Goddard Conference on Mass Storage Systems and Technologies. As one of an ongoing series, this conference continues to serve as a unique medium for the exchange of information on topics relating to the ingestion and management of substantial amounts of data and the attendant problems involved. This year's discussion topics include storage architecture, database management, data distribution, file system performance and modeling, and optical recording technology. There will also be a paper on Application Programming Interfaces (API) for a Physical Volume Repository (PVR) defined in Version 5 of the Institute of Electrical and Electronics Engineers (IEEE) Reference Model (RM). In addition, there are papers on specific archives and storage products.

The solar power satellite concepts: The past decade and the next decade

NASA Technical Reports Server (NTRS)

Kraft, C. C., Jr.

1979-01-01

Results of studies on the solar power satellite concept are summarized. The basic advantages are near continuous access to sunlight and freedom from atmospheric effects and cloud cover. The systems definition studies consider photovoltaic and thermal energy conversion systems and find both to be technically feasible, with the photovoltaic approach preferred. A microwave test program is under way which will provide quantitative data on critical parameters, including beam forming and steering accuracy. Ballistic and winged launch vehicles are defined for the transportation of construction materials, with the shuttle expected to provide low cost transportation to and from space. A reference system is outlined for evaluating the concept in terms of environmental and other considerations. Preliminary estimates of natural resource requirements and energy payback intervals are encouraging.

Reactor/Brayton power systems for nuclear electric spacecraft

NASA Technical Reports Server (NTRS)

Layton, J. P.

1980-01-01

Studies are currently underway to assess the technological feasibility of a nuclear-reactor-powered spacecraft propelled by electric thrusters. This vehicle would be capable of performing detailed exploration of the outer planets of the solar system during the remainder of this century. The purpose of this study was to provide comparative information on a closed cycle gas turbine power conversion system. The results have shown that the performance is very competitive and that a 400 kWe space power system is dimensionally compatible with a single Space Shuttle launch. Performance parameters of system mass and radiator area were determined for systems from 100 to 1000 kWe. A 400 kWe reference system received primary attention. The components of this system were defined and a conceptual layout was developed with encouraging results. The preliminary mass determination for the complete power system was very close to the desired goal of 20 kg/kWe. Use of more advanced technology (higher turbine inlet temperature) will substantially improve system performance characteristics.

Progress in defining a standard for file-level metadata

NASA Technical Reports Server (NTRS)

Williams, Joel; Kobler, Ben

1996-01-01

In the following narrative, metadata required to locate a file on tape or collection of tapes will be referred to as file-level metadata. This paper discribes the rationale for and the history of the effort to define a standard for this metadata.

Alternative Fuels Data Center

Science.gov Websites

reasonably available. Practicability and measures of compliance are defined in rules adopted by the standards, measures, targets, and tools to support agencies in reducing greenhouse gas emissions and and measures of compliance are defined in rules adopted by the Department. (Reference Executive Order

Computer memory management system

DOEpatents

Kirk, III, Whitson John

2002-01-01

A computer memory management system utilizing a memory structure system of "intelligent" pointers in which information related to the use status of the memory structure is designed into the pointer. Through this pointer system, The present invention provides essentially automatic memory management (often referred to as garbage collection) by allowing relationships between objects to have definite memory management behavior by use of coding protocol which describes when relationships should be maintained and when the relationships should be broken. In one aspect, the present invention system allows automatic breaking of strong links to facilitate object garbage collection, coupled with relationship adjectives which define deletion of associated objects. In another aspect, The present invention includes simple-to-use infinite undo/redo functionality in that it has the capability, through a simple function call, to undo all of the changes made to a data model since the previous `valid state` was noted.

GPS/REFSAT definition study report for low-cost terminals

NASA Technical Reports Server (NTRS)

1980-01-01

A relay transponder, located either on a satellite in geostationary orbit or on a local tower to relay acquisition-aiding data, ephemerides, etc, from a ground-based remote control station to a GPS civil user terminal located on a ship or land-transportation vehicle is described. Termed REFSAT (Reference Satellite), this concept reduces the circuit complexity and cost of user terminals. The various systems needed to implement the REFSAT concept for low-cost, GPS civil terminals are defined. The GPS/REFSAT system compatible with the NAVSTAR GPS system consists of a geostationary relay satellite, civil user terminals, and the central facility which performs operations common to all users for relay via the space segment. A GPS/REFSAT system utilizing a local tower for the relay transponder is described, results of a study of civil user requirements are presented, and specifications for the GPS/REFSAT system and its individual segments are included.

Standardisation of DNA quantitation by image analysis: quality control of instrumentation.

PubMed

Puech, M; Giroud, F

1999-05-01

DNA image analysis is frequently performed in clinical practice as a prognostic tool and to improve diagnosis. The precision of prognosis and diagnosis depends on the accuracy of analysis and particularly on the quality of image analysis systems. It has been reported that image analysis systems used for DNA quantification differ widely in their characteristics (Thunissen et al.: Cytometry 27: 21-25, 1997). This induces inter-laboratory variations when the same sample is analysed in different laboratories. In microscopic image analysis, the principal instrumentation errors arise from the optical and electronic parts of systems. They bring about problems of instability, non-linearity, and shading and glare phenomena. The aim of this study is to establish tools and standardised quality control procedures for microscopic image analysis systems. Specific reference standard slides have been developed to control instability, non-linearity, shading and glare phenomena and segmentation efficiency. Some systems have been controlled with these tools and these quality control procedures. Interpretation criteria and accuracy limits of these quality control procedures are proposed according to the conclusions of a European project called PRESS project (Prototype Reference Standard Slide). Beyond these limits, tested image analysis systems are not qualified to realise precise DNA analysis. The different procedures presented in this work determine if an image analysis system is qualified to deliver sufficiently precise DNA measurements for cancer case analysis. If the controlled systems are beyond the defined limits, some recommendations are given to find a solution to the problem.

Precision star-tracking telescope

NASA Technical Reports Server (NTRS)

Fairbank, W. M.; Everitt, C. W. F.

1972-01-01

The design, construction, and preliminary testing of a new high accuracy star tracking telescope for the laboratory model of the Stanford gyro relativity experiment are described. The function of the telescope in the final flight experiment is to define (by reference to a suitable star) a direction in space for comparison with the relativistic precession of a group of gyroscopes. The design of the telescope has been strongly affected by designs for other portions of the overall experiments, for example the gyroscopes, the attitude control system of the satellite, and the instrumentation system used in processing relativity data. Main goals for the star tracker are: (1) independent readout of angular position in two planes; (2) absolute null stability over a one year period of mechanical parts; (3) readout linear to 0.001 arc-seconds over + or - 0.05 arc-second; (4) noise performance leading to a resolution of 0.05 arc-second in 0.1 second observation time of the chosen reference star; and (5) provision for automatic gain control capable of matching the gains of the gyroscopes and telescope readouts to 1% or better.

Modeling a Mathematical to Quantify the Degree of Emergency Department Crowding

NASA Astrophysics Data System (ADS)

Chang, Y.; Pan, C.; Wen, J.

2012-12-01

The purpose of this study is to deduce a function from the admissions/discharge rate of patient flow to estimate a "Critical Point" that provides a reference for warning systems in regards to crowding in the emergency department (ED) of a hospital or medical clinic. In this study, a model of "Input-Throughput-Output" was used in our established mathematical function to evaluate the critical point. The function was defined as ∂ρ/∂t=-K×∂ρ/∂x , where ρ= number of patients per unit distance (also called density), t= time, x= distance, K= distance of patients movement per unit time. Using the average K of ED crowding, we could initiate the warning system at appropriate time and plan necessary emergency response to facilitate the patient process more smoothly. It was concluded that ED crowding can be quantified using the average value of K, and the value can be used as a reference for medical staff to give optimal emergency medical treatment to patients. Therefore, additional practical work should be launched to collect more precise quantitative data.

Construction of CASCI-type wave functions for very large active spaces.

PubMed

Boguslawski, Katharina; Marti, Konrad H; Reiher, Markus

2011-06-14

We present a procedure to construct a configuration-interaction expansion containing arbitrary excitations from an underlying full-configuration-interaction-type wave function defined for a very large active space. Our procedure is based on the density-matrix renormalization group (DMRG) algorithm that provides the necessary information in terms of the eigenstates of the reduced density matrices to calculate the coefficient of any basis state in the many-particle Hilbert space. Since the dimension of the Hilbert space scales binomially with the size of the active space, a sophisticated Monte Carlo sampling routine is employed. This sampling algorithm can also construct such configuration-interaction-type wave functions from any other type of tensor network states. The configuration-interaction information obtained serves several purposes. It yields a qualitatively correct description of the molecule's electronic structure, it allows us to analyze DMRG wave functions converged for the same molecular system but with different parameter sets (e.g., different numbers of active-system (block) states), and it can be considered a balanced reference for the application of a subsequent standard multi-reference configuration-interaction method.

Orbital Signature Analyzer (OSA): A spacecraft health/safety monitoring and analysis tool

NASA Technical Reports Server (NTRS)

Weaver, Steven; Degeorges, Charles; Bush, Joy; Shendock, Robert; Mandl, Daniel

1993-01-01

Fixed or static limit sensing is employed in control centers to ensure that spacecraft parameters remain within a nominal range. However, many critical parameters, such as power system telemetry, are time-varying and, as such, their 'nominal' range is necessarily time-varying as well. Predicted data, manual limits checking, and widened limit-checking ranges are often employed in an attempt to monitor these parameters without generating excessive limits violations. Generating predicted data and manual limits checking are both resource intensive, while broadening limit ranges for time-varying parameters is clearly inadequate to detect all but catastrophic problems. OSA provides a low-cost solution by using analytically selected data as a reference upon which to base its limits. These limits are always defined relative to the time-varying reference data, rather than as fixed upper and lower limits. In effect, OSA provides individual limits tailored to each value throughout all the data. A side benefit of using relative limits is that they automatically adjust to new reference data. In addition, OSA provides a wealth of analytical by-products in its execution.

The next century astrophysics program

NASA Technical Reports Server (NTRS)

Swanson, Paul N.

1992-01-01

The Astrophysics Division within the NASA Office of Space Science and Applications (OSSA) has defined a set of flagship and intermediate missions that are presently under study for possible launch during the next 20 years. These missions and tentative schedules, referred to as the Astrotech 21 Mission Set, are summarized. The missions are in three groups corresponding to the cognizant science branch within the Astrophysics Division. Phase C/D refers to the pre-launch construction and delivery of the spacecraft, and the Operations Phase refers to the period when the mission is active in space. Approximately 1.5 years before the start of Phase C/D, a non-advocate review (NAR) is held to ensure that the mission/system concept and the requisite technology are at an appropriate stage of readiness for full scale development to begin. Therefore, technology development is frozen (usually) as of the date of a successful NAR. An overview of the technology advances required for each of the three wavelength groups is provided in the following paragraphs, along with a brief description of the individual missions.

Acceptable health and priority weighting: Discussing a reference-level approach using sufficientarian reasoning.

PubMed

Wouters, S; van Exel, N J A; Rohde, K I M; Vromen, J J; Brouwer, W B F

2017-05-01

Health care systems are challenged in allocating scarce health care resources, which are typically insufficient to fulfil all health care wants and needs. One criterion for priority setting may be the 'acceptable health' approach, which suggests that society may want to assign higher priority to health benefits in people with "unacceptable" than in people with "acceptable" health. A level of acceptable health then serves as a reference point for priority setting. Empirical research has indicated that people may be able and willing to define health states as "unacceptable" or "acceptable", but little attention has been given to the normative implications of evaluating health benefits in relation to a reference level of acceptable health. The current paper aims to address this gap by relating insights from the distributive justice literature, i.e. the sufficientarian literature, to the acceptable health approach, as we argue that these approaches are related. We specifically focus on the implications of an 'acceptability' approach for priority weighting of health benefits, derived from sufficientarian reasoning and debates, and assess the moral implications of such weighting. Copyright © 2017 Elsevier Ltd. All rights reserved.

How To Refer to People with Disabilities: A Primer for Laypeople.

ERIC Educational Resources Information Center

Beadles, Robert J., Jr.

2001-01-01

This article discusses the movement toward focusing on the individual rather than the disabling condition when referring to people with disabilities and contrasts acceptable and unacceptable terminology for people with different types of disabilities. The terms "impairment,""disability," and "handicap" are defined. (CR)

Quadrature, Interpolation and Observability

NASA Technical Reports Server (NTRS)

Hodges, Lucille McDaniel

1997-01-01

Methods of interpolation and quadrature have been used for over 300 years. Improvements in the techniques have been made by many, most notably by Gauss, whose technique applied to polynomials is referred to as Gaussian Quadrature. Stieltjes extended Gauss's method to certain non-polynomial functions as early as 1884. Conditions that guarantee the existence of quadrature formulas for certain collections of functions were studied by Tchebycheff, and his work was extended by others. Today, a class of functions which satisfies these conditions is called a Tchebycheff System. This thesis contains the definition of a Tchebycheff System, along with the theorems, proofs, and definitions necessary to guarantee the existence of quadrature formulas for such systems. Solutions of discretely observable linear control systems are of particular interest, and observability with respect to a given output function is defined. The output function is written as a linear combination of a collection of orthonormal functions. Orthonormal functions are defined, and their properties are discussed. The technique for evaluating the coefficients in the output function involves evaluating the definite integral of functions which can be shown to form a Tchebycheff system. Therefore, quadrature formulas for these integrals exist, and in many cases are known. The technique given is useful in cases where the method of direct calculation is unstable. The condition number of a matrix is defined and shown to be an indication of the the degree to which perturbations in data affect the accuracy of the solution. In special cases, the number of data points required for direct calculation is the same as the number required by the method presented in this thesis. But the method is shown to require more data points in other cases. A lower bound for the number of data points required is given.

Building a semantic web-based metadata repository for facilitating detailed clinical modeling in cancer genome studies.

PubMed

Sharma, Deepak K; Solbrig, Harold R; Tao, Cui; Weng, Chunhua; Chute, Christopher G; Jiang, Guoqian

2017-06-05

Detailed Clinical Models (DCMs) have been regarded as the basis for retaining computable meaning when data are exchanged between heterogeneous computer systems. To better support clinical cancer data capturing and reporting, there is an emerging need to develop informatics solutions for standards-based clinical models in cancer study domains. The objective of the study is to develop and evaluate a cancer genome study metadata management system that serves as a key infrastructure in supporting clinical information modeling in cancer genome study domains. We leveraged a Semantic Web-based metadata repository enhanced with both ISO11179 metadata standard and Clinical Information Modeling Initiative (CIMI) Reference Model. We used the common data elements (CDEs) defined in The Cancer Genome Atlas (TCGA) data dictionary, and extracted the metadata of the CDEs using the NCI Cancer Data Standards Repository (caDSR) CDE dataset rendered in the Resource Description Framework (RDF). The ITEM/ITEM_GROUP pattern defined in the latest CIMI Reference Model is used to represent reusable model elements (mini-Archetypes). We produced a metadata repository with 38 clinical cancer genome study domains, comprising a rich collection of mini-Archetype pattern instances. We performed a case study of the domain "clinical pharmaceutical" in the TCGA data dictionary and demonstrated enriched data elements in the metadata repository are very useful in support of building detailed clinical models. Our informatics approach leveraging Semantic Web technologies provides an effective way to build a CIMI-compliant metadata repository that would facilitate the detailed clinical modeling to support use cases beyond TCGA in clinical cancer study domains.

The Representation of Cultural Heritage from Traditional Drawing to 3d Survey: the Case Study of Casamary's Abbey

NASA Astrophysics Data System (ADS)

Canciani, M.; Saccone, M.

2016-06-01

In 3D survey the aspects most discussed in the scientific community are those related to the acquisition of data from integrated survey (laser scanner, photogrammetric, topographic and traditional direct), rather than those relating to the interpretation of the data. Yet in the methods of traditional representation, the data interpretation, such as that of the philological reconstruction, constitutes the most important aspect. It is therefore essential in modern systems of survey and representation, filter the information acquired. In the system, based on the integrated survey that we have adopted, the 3D object, characterized by a cloud of georeferenced points, defined but their color values, defines the core of the elaboration. It allows to carry out targeted analysis, using section planes as a tool of selection and filtering data, comparable with those of traditional drawings. In the case study of the Abbey of Casamari (Veroli), one of the most important Cistercian Settlement in Italy, the survey made for an Agreement with the Ministry of Cultural Heritage and Activities and Tourism (MiBACT) and University of RomaTre, within the project "Accessment of the sismic safety of the state museum", the reference 3D model, consisting of the superposition and geo-references data from various surveys, is the tool with which yo develop representative models comparable to traditional ones. It provides the necessary spatial environment for drawing up plans and sections with a definition such as to develop thematic analysis related to phases of construction, state of deterioration and structural features.

Looking back - Looking forward: A novel multi-time slice weight-of-evidence approach for defining reference conditions to assess the impact of human activities on lake systems.

PubMed

Hollert, Henner; Crawford, Sarah E; Brack, Werner; Brinkmann, Markus; Fischer, Elske; Hartmann, Kai; Keiter, Steffen; Ottermanns, Richard; Ouellet, Jacob D; Rinke, Karsten; Rösch, Manfred; Roß-Nickoll, Martina; Schäffer, Andreas; Schüth, Christoph; Schulze, Tobias; Schwarz, Anja; Seiler, Thomas-Benjamin; Wessels, Martin; Hinderer, Matthias; Schwalb, Antje

2018-06-01

Lake ecosystems are sensitive recorders of environmental changes that provide continuous archives at annual to decadal resolution over thousands of years. The systematic investigation of land use changes and emission of pollutants archived in Holocene lake sediments as well as the reconstruction of contamination, background conditions, and sensitivity of lake systems offer an ideal opportunity to study environmental dynamics and consequences of anthropogenic impact that increasingly pose risks to human well-being. This paper discusses the use of sediment and other lines of evidence in providing a record of historical and current contamination in lake ecosystems. We present a novel approach to investigate impacts from human activities using chemical-analytical, bioanalytical, ecological, paleolimnological, paleoecotoxicological, archeological as well as modeling techniques. This multi-time slice weight-of-evidence (WOE) approach will generate knowledge on conditions prior to anthropogenic influence and provide knowledge to (i) create a better understanding of the effects of anthropogenic disturbances on biodiversity, (ii) assess water quality by using quantitative data on historical pollution and persistence of pollutants archived over thousands of years in sediments, and (iii) define environmental threshold values using modeling methods. This technique may be applied in order to gain insights into reference conditions of surface and ground waters in catchments with a long history of land use and human impact, which is still a major need that is currently not yet addressed within the context of the European Water Framework Directive. Copyright © 2018 Elsevier B.V. All rights reserved.

Cost Optimal Elastic Auto-Scaling in Cloud Infrastructure

NASA Astrophysics Data System (ADS)

Mukhopadhyay, S.; Sidhanta, S.; Ganguly, S.; Nemani, R. R.

2014-12-01

Today, elastic scaling is critical part of leveraging cloud. Elastic scaling refers to adding resources only when it is needed and deleting resources when not in use. Elastic scaling ensures compute/server resources are not over provisioned. Today, Amazon and Windows Azure are the only two platform provider that allow auto-scaling of cloud resources where servers are automatically added and deleted. However, these solution falls short of following key features: A) Requires explicit policy definition such server load and therefore lacks any predictive intelligence to make optimal decision; B) Does not decide on the right size of resource and thereby does not result in cost optimal resource pool. In a typical cloud deployment model, we consider two types of application scenario: A. Batch processing jobs → Hadoop/Big Data case B. Transactional applications → Any application that process continuous transactions (Requests/response) In reference of classical queuing model, we are trying to model a scenario where servers have a price and capacity (size) and system can add delete servers to maintain a certain queue length. Classical queueing models applies to scenario where number of servers are constant. So we cannot apply stationary system analysis in this case. We investigate the following questions 1. Can we define Job queue and use the metric to define such a queue to predict the resource requirement in a quasi-stationary way? Can we map that into an optimal sizing problem? 2. Do we need to get into a level of load (CPU/Data) on server level to characterize the size requirement? How do we learn that based on Job type?

Spatial vision within egocentric and exocentric frames of reference

NASA Technical Reports Server (NTRS)

Howard, Ian P.

1991-01-01

It is remarkable that we are able to perceive a stable visual world and judge the directions, orientations, and movements of visual objects given that images move on the retina, the eyes move in the head, the head moves on the body, and the body moves in space. An understanding of the mechanisms underlying perceptual stability and spatial judgements requires precise definitions of relevant coordinate systems. An egocentric frame of reference is defined with respect to some part of the observer. There are four principal egocentric frames of reference, a station-point frame associated with the nodal point of the eye, an retinocentric frame associated with the retina, a headcentric frame associated with the head, and a bodycentric frame (torsocentric) associated with the torso. Additional egocentric frames can be identified with respect to any segment of the body. An egocentric task is one in which the position, orientation, or motion of an object is judged with respect to an egocentric frame of reference. A proprioceptive is a special kind of egocentric task in which the object being judged is also part of the body. An example of a proprioceptive task is that of directing the gaze toward the seen or unseen toe. An exocentric frame of reference is external to the observer. Geographical coordinates and the direction of gravity are examples of exocentric frames of reference. These various frames are listed in tabular form, together with examples of judgements of each type.

Evaluating the sustainability of space life support systems: case study on air revitalisation systems ARES and BIORAT

NASA Astrophysics Data System (ADS)

Suomalainen, Emilia; Erkman, Suren

Space life support systems can be taken as kinds of miniature models of industrial systems found on Earth. The term "industrial" is employed here in a generic sense, referring to all human technological activities. The time scale as well as the physical scope of space life support systems is reduced compared to most terrestrial systems and so is consequently their complexity. These systems can thus be used as a kind of a "laboratory of sustainability" to examine concerns related to the environmental sustainability of industrial systems and in particular to their resource use. Two air revitalisation systems, ARES and BIORAT, were chosen as the test cases of our study. They represent respectively a physico-chemical and a biological life support system. In order to analyse the sustainability of these systems, we began by constructing a generic system representation applicable to both these systems (and to others). The metabolism of the systems was analysed by performing Material Flow Analyses—MFA is a tool frequently employed on terrestrial systems in the field of industrial ecology. Afterwards, static simulation models were developed for both ARES and BIORAT, focusing, firstly, on the oxygen balances of the systems and, secondly, on the total mass balances. It was also necessary to define sustainability indicators adapted to space life support systems in order to evaluate and to compare the performances of ARES and BIORAT. The defined indicators were partly inspired from concepts used in Material Flow Accounting and they were divided into four broad categories: 1. recycling and material use efficiency, 2. autarky and coverage time, 3. resource use and waste creation, and 4. system mass and energy consumption. The preliminary results of our analyses show that the performance of BIORAT is superior compared to ARES in terms of the defined resource use indicators. BIORAT seems especially effective in reprocessing carbon dioxide created by human metabolism. The performances of ARES and BIORAT are somewhat closer in terms of material use efficiency and resource intensity. However, the excellence of BIORAT in terms of resource use is countered by the fact that its energy consumption is greater than that of ARES by a factor of ten.

Determination of the extragalactic-planetary frame tie from joint analysis of radio interferometric and lunar laser ranging measurements

NASA Technical Reports Server (NTRS)

Folkner, W. M.; Charlot, P.; Finger, M. H.; Williams, J. G.; Sovers, O. J.; Newhall, XX; Standish, E. M., Jr.

1994-01-01

Very Long Baseline Interferometry (VLBI) observations of extragalactic radio sources provide the basis for defining an accurate non-rotating reference frame in terms of angular positions of the sources. Measurements of the distance from the Earth to the Moon and to the inner planets provide the basis for defining an inertial planetary ephemeris reference frame. The relative orientation, or frame tie, between these two reference frames is of interest for combining Earth orientation measurements, for comparing Earth orientation results with theories referred to the mean equator and equinox, and for determining the positions of the planets with respect to the extragalactic reference frame. This work presents an indirect determination of the extragalactic-planetary frame tie from a combined reduction of VLBI and Lunar Laser Ranging (LLR) observations. For this determination, data acquired by LLR tracking stations since 1969 have been analyzed and combined with 14 years of VLBI data acquired by NASA's Deep Space Network since 1978. The frame tie derived from this joint analysis, with an accuracy of 0.003 sec, is the most accurate determination obtained so far. This result, combined with a determination of the mean ecliptic (defined in the rotating sense), shows that the mean equinox of epoch J2000 is offset from the x-axis of the extragalactic frame adopted by the International Earth Rotation Service for astrometric and geodetic applications by 0.078 sec +/- 0.010 sec along the y-direction and y 0.019 sec +/- 0.001 sec. along the z-direction.

Reflecting on the structure of soil classification systems: insights from a proposal for integrating subsoil data into soil information systems

NASA Astrophysics Data System (ADS)

Dondeyne, Stefaan; Juilleret, Jérôme; Vancampenhout, Karen; Deckers, Jozef; Hissler, Christophe

2017-04-01

Classification of soils in both World Reference Base for soil resources (WRB) and Soil Taxonomy hinges on the identification of diagnostic horizons and characteristics. However as these features often occur within the first 100 cm, these classification systems convey little information on subsoil characteristics. An integrated knowledge of the soil, soil-to-substratum and deeper substratum continuum is required when dealing with environmental issues such as vegetation ecology, water quality or the Critical Zone in general. Therefore, we recently proposed a classification system of the subsolum complementing current soil classification systems. By reflecting on the structure of the subsoil classification system which is inspired by WRB, we aim at fostering a discussion on some potential future developments of WRB. For classifying the subsolum we define Regolite, Saprolite, Saprock and Bedrock as four Subsolum Reference Groups each corresponding to different weathering stages of the subsoil. Principal qualifiers can be used to categorize intergrades of these Subsoil Reference Groups while morphologic and lithologic characteristics can be presented with supplementary qualifiers. We argue that adopting a low hierarchical structure - akin to WRB and in contrast to a strong hierarchical structure as in Soil Taxonomy - offers the advantage of having an open classification system avoiding the need for a priori knowledge of all possible combinations which may be encountered in the field. Just as in WRB we also propose to use principal and supplementary qualifiers as a second level of classification. However, in contrast to WRB we propose to reserve the principal qualifiers for intergrades and to regroup the supplementary qualifiers into thematic categories (morphologic or lithologic). Structuring the qualifiers in this manner should facilitate the integration and handling of both soil and subsoil classification units into soil information systems and calls for paying attention to these structural issues in future developments of WRB.

A quasiparticle-based multi-reference coupled-cluster method.

PubMed

Rolik, Zoltán; Kállay, Mihály

2014-10-07

The purpose of this paper is to introduce a quasiparticle-based multi-reference coupled-cluster (MRCC) approach. The quasiparticles are introduced via a unitary transformation which allows us to represent a complete active space reference function and other elements of an orthonormal multi-reference (MR) basis in a determinant-like form. The quasiparticle creation and annihilation operators satisfy the fermion anti-commutation relations. On the basis of these quasiparticles, a generalization of the normal-ordered operator products for the MR case can be introduced as an alternative to the approach of Mukherjee and Kutzelnigg [Recent Prog. Many-Body Theor. 4, 127 (1995); Mukherjee and Kutzelnigg, J. Chem. Phys. 107, 432 (1997)]. Based on the new normal ordering any quasiparticle-based theory can be formulated using the well-known diagram techniques. Beyond the general quasiparticle framework we also present a possible realization of the unitary transformation. The suggested transformation has an exponential form where the parameters, holding exclusively active indices, are defined in a form similar to the wave operator of the unitary coupled-cluster approach. The definition of our quasiparticle-based MRCC approach strictly follows the form of the single-reference coupled-cluster method and retains several of its beneficial properties. Test results for small systems are presented using a pilot implementation of the new approach and compared to those obtained by other MR methods.

Trajectory Specification for Terminal Air Traffic: Pairwise Conflict Detection and Resolution

NASA Technical Reports Server (NTRS)

Paielli, Russell A.; Erzberger, Heinz

2017-01-01

Trajectory Specification is the explicit bounding and control of aircraft trajectories such that the position at any point in time is constrained to a precisely defined volume of space. The bounding space is defined by cross-track, along-track, and vertical tolerances relative to a reference trajectory that specifies position as a function of time. The tolerances are dynamic and will be based on the aircraft navigation capabilities and the current traffic situation. Assuming conformance, Trajectory Specification can guarantee safe separation for an arbitrary period of time even in the event of an air traffic control (ATC) system or datalink failure; hence it can help to achieve the high level of safety and reliability needed for ATC automation. It can also reduce the reliance on tactical backup systems during normal operation. This paper applies it to the terminal area around a major airport and presents algorithms and software for detecting and resolving conflicts. A representative set of pairwise conflicts was generated, and a fast-time simulation was run on them. All conflicts were successfully resolved in real time, demonstrating the computational feasibility of the concept.

An Introduction to the Global Space-based Inter-Calibration System from a EUMETSAT Perspective

NASA Astrophysics Data System (ADS)

Wagner, S. C.; Hewison, T.; Roebeling, R. A.; Koenig, M.; Schulz, J.; Miu, P.

2012-04-01

The Global Space-based Inter-Calibration System (GSICS) (Goldberg and al. 2011) is an international collaborative effort which aims to monitor, improve and harmonize the quality of observations from operational weather and environmental satellites of the Global Observing System (GOS). GSICS aims at ensuring consistent accuracy among space-based observations worldwide for climate monitoring, weather forecasting, and environmental applications. This is achieved through a comprehensive calibration strategy, which involves monitoring instrument performances, operational inter-calibration of satellite instruments, tying the measurements to absolute references and standards, and recalibration of archived data. A major part of this strategy involves direct comparison of collocated observations from pairs of satellite instruments, which are used to systematically generate calibration functions to compare and correct the calibration of monitored instruments to references. These GSICS Corrections are needed for accurately integrating data from multiple observing systems into both near real-time and re-analysis products, applications and services. This paper gives more insight into the activities carried out by EUMETSAT as a GSICS Processing and Research Centre. Currently these are closely bound to the in-house development and operational implementation of calibration methods for solar and thermal band channels of geostationary and polar-orbiting satellites. They include inter-calibration corrections for Meteosat imagers using reference instruments such as the Moderate Resolution Imaging Spectroradiometer (MODIS) on-board the Aqua satellite for solar band channels, the Infrared Atmospheric Sounding Interferometer (IASI) on-board Metop-A and, for historic archive data, the High-resolution InfraRed Sounder (HIRS). Additionally, bias monitoring is routinely performed, allowing users to visualise the calibration accuracy of the instruments in near real-time. These activities are based on principles and protocols defined by the GSICS Research Working Group and Data Management Working Group, which require assessment of the calibration uncertainties to ensure the traceability to community references.