Science.gov

Sample records for regenerated cellulose membrane

  1. Modification of regenerated cellulose membrane based on thiol dendrimer.

    PubMed

    Vázquez, M Isabel; Algarra, Manuel; Benavente, Juana

    2015-10-20

    This work describes the modification of a highly swollen commercial regenerated cellulose (RC) membrane with a dendritic molecule (thiol DAB dendrimer of generation 3) by the dip coating method, and its possible use in electrochemical systems with saline solutions fluxes. Moreover, cellulosic membrane modification with dendrimer covered-CdSe quantum dot was also performed, since it allows dendrimer assortment by fluorescence. Changes in electrical, mechanical and diffusive membrane parameters were determined by impedance spectroscopy, elasticity curves and diffusional permeability measurements. The results indicate a reduction in the free volume of the RC chains in the original membrane associated with the thiol dendrimer inclusion, which reduces diffusive permeability. This demonstrates the possibility of using the thiol dendrimer-modified membrane in low/medium concentration level (0.001M/0.01M) devices with NaCl and PbCl2 solutions.

  2. The effect of bacterial cellulose membrane compared with collagen membrane on guided bone regeneration

    PubMed Central

    Lim, Youn-Mook; Jeong, Sung In; An, Sung-Jun; Kang, Seong-Soo

    2015-01-01

    PURPOSE This study was to evaluate the effects of bacterial cellulose (BC) membranes as a barrier membrane on guided bone regeneration (GBR) in comparison with those of the resorbable collagen membranes. MATERIALS AND METHODS BC membranes were fabricated using biomimetic technology. Surface properties were analyzed, Mechanical properties were measured, in vitro cell proliferation test were performed with NIH3T3 cells and in vivo study were performed with rat calvarial defect and histomorphometric analysis was done. The Mann-Whitney U test and the Wilcoxon signed rank test was used (α<.05). RESULTS BC membrane showed significantly higher mechanical properties such as wet tensile strength than collagen membrane and represented a three-dimensional multilayered structure cross-linked by nano-fibers with 60 % porosity. In vitro study, cell adhesion and proliferation were observed on BC membrane. However, morphology of the cells was found to be less differentiated, and the cell proliferation rate was lower than those of the cells on collagen membrane. In vivo study, the grafted BC membrane did not induce inflammatory response, and maintained adequate space for bone regeneration. An amount of new bone formation in defect region loaded with BC membrane was significantly similar to that of collagen membrane application. CONCLUSION BC membrane has potential to be used as a barrier membrane, and efficacy of the membrane on GBR is comparable to that of collagen membrane. PMID:26816579

  3. Regenerated Cellulose Capsules for Controlled Drug Delivery, Part 2: Modulating Membrane Permeability by Incorporation of Depolymerized Cellulose and Altering Membrane Thickness.

    PubMed

    Bhatt, Bhavik; Kumar, Vijay

    2015-12-01

    For application of regenerated cellulose (RC) membranes in capsule dosage forms, the methods to modify drug release from these membranes are described. Membranes were fabricated by blending native and depolymerized celluloses dissolved in dimethyl sulfoxide and paraformaldehyde solvent system, prior to casting on molds, precipitation in water, and thermal annealing. The effect of laminating layers of RC to fabricate membranes with increasing thickness was also investigated. Solute diffusion studies using ionic and hydrophobic solutes, as well as large protein molecules, were conducted in side-by-side diffusion cells. Microscopic as well as physiological evaluation of these membranes indicated that pore size, porosity, and water uptake decreased as the fraction of depolymerized cellulose increased in the membranes. Permeability analysis of small ionic and hydrophobic solutes indicated that the solute transport across the hydrated membrane occurs through diffusion in the water-filled pores that are formed in situ. The apparent path for solute diffusion increases as the fraction of depolymerized cellulose increases. Permeability analysis of large protein molecules indicated that the pore sizes and distribution in these membranes is heterogeneous. Increasing the membrane thickness by lamination of RC does not influence porosity but causes formation of dead-end pores because of blocking by subsequent laminate layers.

  4. Demonstration and Validation of a Regenerated Cellulose Dialysis Membrane Diffusion Sampler for Monitoring Groundwater Quality and Remediation Progress at DoD Sites

    DTIC Science & Technology

    2007-02-01

    trace elements that did not equilibrate within 28 days. Equilibration times for selected explosive compounds through dialysis membranes were...PROTOCOL Demonstration and Validation of a Regenerated Cellulose Dialysis Membrane Diffusion Sampler for Monitoring Groundwater Quality and...Demonstration and Validation of a Regenerated Cellulose Dialysis Membrane Diffusion Sampler for Monitoring Groundwater Quality and Remediation Progress at DoD

  5. Chemical surface, diffusional, electrical and elastic characterizations of two different dense regenerated cellulose membranes.

    PubMed

    Vázquez, M I; de Lara, R; Benavente, J

    2008-12-15

    A comparison of NaCl transport across two dense cellulosic membranes from different suppliers is presented. Hydraulic and diffusional permeabilities were determined from volume flow-applied pressure and concentration-time relationships, while cation transport number and membrane conductivity were determined from electromotrice force and impedance spectroscopy measurements, respectively. Chemical surface differences between both membranes are correlated to transport parameters and morphology, but differences in elastic properties of both membranes might also be considered in order to get a more complete picture of membrane behaviors and to obtain structural-transport parameters correlations.

  6. Demonstration and Validation of a Regenerated Cellulose Dialysis Membrane Diffusion Sampler for Monitoring Ground-Water Quality and Remediation Progress at DoD Sites

    DTIC Science & Technology

    2010-04-01

    Ehlke et al. (2004) conducted laboratory studies using RCDM and demonstrated that water inside the membranes could equilibrate with selected inorganics...Validation of a Regenerated Cellulose Dialysis Membrane Diffusion Sampler for Monitoring Ground-Water Quality and Remediation Progress at DoD Sites...Cellulose Dialysis Membrane Diffusion Sampler for Monitoring Ground-Water Quality and Remediation Progress at DoD Sites 5a. CONTRACT NUMBER 5b. GRANT

  7. Production of permeable cellulose triacetate membranes

    DOEpatents

    Johnson, Bruce M.

    1986-01-01

    A phase inversion process for the preparation of cellulose triacetate (CTA) and regenerated cellulose membranes is disclosed. Such membranes are useful as supports for liquid membranes in facilitated transport processes, as microfiltration membranes, as dialysis or ultrafiltration membranes, and for the preparation of ion-selective electrodes. The process comprises the steps of preparing a casting solution of CTA in a solvent comprising a mixture of cyclohexanone and methylene chloride, casting a film from the casting solution, and immersing the cast film in a methanol bath. The resulting CTA membrane may then be hydrolyzed to regenerated cellulose using conventional techniques.

  8. Production of permeable cellulose triacetate membranes

    DOEpatents

    Johnson, B.M.

    1986-12-23

    A phase inversion process for the preparation of cellulose triacetate (CTA) and regenerated cellulose membranes is disclosed. Such membranes are useful as supports for liquid membranes in facilitated transport processes, as microfiltration membranes, as dialysis or ultrafiltration membranes, and for the preparation of ion-selective electrodes. The process comprises the steps of preparing a casting solution of CTA in a solvent comprising a mixture of cyclohexanone and methylene chloride, casting a film from the casting solution, and immersing the cast film in a methanol bath. The resulting CTA membrane may then be hydrolyzed to regenerated cellulose using conventional techniques.

  9. Para-aminobenzamidine linked regenerated cellulose membranes for plasminogen activator purification: effect of spacer arm length and ligand density.

    PubMed

    Fasoli, Ezio; Reyes, Yiaslin Ruiz; Guzman, Osiris Martinez; Rosado, Alexandra; Cruz, Vivian Rodriguez; Borges, Amaris; Martinez, Edmarie; Bansal, Vibha

    2013-07-01

    Despite membrane-based separations offering superior alternative to packed bed chromatographic processes, there has been a substantial lacuna in their actual application to separation processes. One of the major reasons behind this is the lack of availability of appropriately modified or end-group modifiable membranes. In this paper, an affinity membrane was developed using a commercially available serine protease inhibitor, para-aminobenzamidine (pABA). The membrane modification was optimized for protein binding capacity by varying: (i) the length of the spacer arm (SA; 5-atoms, 7-atoms, and 14-atoms) linking the ligand to membrane surface; (ii) the affinity ligand (pABA) density on membrane surface (5-25nmol/cm(2)). Resulting membranes were tested for their ability to bind plasminogen activators (PAs) from mono- and multi-component systems in batch mode. The membrane containing pABA linked through 7-atoms SA but similar ligand density as in the case of 5- or 14-atoms long SA was found to bind up to 1.6-times higher amounts of PA per nmoles of immobilized ligand from conditioned HeLa cell culture media. However, membranes with similar ligand densities but different lengths of SA, showed comparable binding capacities in mono-component system. In addition, the length of SA did not affect the selectivity of the ligand for PA. A clear inverse linear correlation was observed between ligand density and binding capacity until the point of PA binding optima was reached (11±1.0nmol/cm(2)) in mono- and multi-component systems for 7- as well as 14-atoms SA. Up to 200-fold purification was achieved in a single step separation of PA from HeLa conditioned media using these affinity membranes. The issues of ligand leaching and reuse of the membranes were also investigated. An extensive regeneration procedure allowed the preservation of approximately 95% of the PA binding capacity of the membranes even after five cycles of use.

  10. Steric exclusion chromatography for purification of cell culture-derived influenza A virus using regenerated cellulose membranes and polyethylene glycol.

    PubMed

    Marichal-Gallardo, Pavel; Pieler, Michael M; Wolff, Michael W; Reichl, Udo

    2017-02-03

    Steric exclusion chromatography has been used for the purification of proteins and bacteriophages using monoliths. The operation is carried out by mixing a crude sample containing the target species with a predetermined concentration and molecular weight of polyethylene glycol (PEG) and loading it onto a non-reactive hydrophilic surface. Product capture occurs by the mutual steric exclusion of PEG between the product and the matrix. Selectivity is significantly influenced by target product size. Product elution is achieved by decreasing the PEG concentration. In this study, a 75cm(2) cellulose membrane adsorber was used for the purification of a clarified and inactivated influenza A virus broth produced in a 5L bioreactor using suspension Madin Darby canine kidney cells. Product recovery was above 95% based on hemagglutination activity and single radial immunodiffusion assays. Maximum depletion of double stranded host cell DNA and total protein was 99.7% and 92.4%, respectively. Purified virus particles showed no aggregation with a monodisperse peak around 84nm. 250mL of the clarified inactivated virus broth was purified within 40min. The surface area productivity based on the recovery of the viral hemagglutinin antigen was 28-50mgm(-2)h(-1) depending on the feed and loading conditions.

  11. Preparation and properties of regenerated cellulose hydrogels

    NASA Astrophysics Data System (ADS)

    Zhou, L.; Xie, F.; Li, H.; Li, W.; Li, W. J.; Li, Y. W.

    2017-02-01

    The regenerated cellulose (RCE) hydrogels were successfully prepared via an easy and green environmental method in N-methylmorpholine-N-oxide (NMMO) aqueous solution. The effect of cellulose content on the thermostability properties, swelling behavior and retention rate of hydrogels was investigated. The thermostability of RCE hydrogels was slightly enhanced with the addition of 8 wt% cellulose, the highest decomposition temperature rose from 335 °C to 352 °C, and the least heat loss is about 75.60%. The equilibrium swelling ratio increases from 394.12% for 3% cellulose hydrogels to 619.46% for 8% cellulose hydrogels. The retention ratio increases from 1.13% to 28.46%.

  12. Electrospun regenerated cellulose nanofibrous membranes surface-grafted with polymer chains/brushes via the atom transfer radical polymerization method for catalase immobilization.

    PubMed

    Feng, Quan; Hou, Dayin; Zhao, Yong; Xu, Tao; Menkhaus, Todd J; Fong, Hao

    2014-12-10

    In this study, an electrospun regenerated cellulose (RC) nanofibrous membrane with fiber diameters of ∼200-400 nm was prepared first; subsequently, 2-hydroxyethyl methacrylate (HEMA), 2-dimethylaminoethyl methacrylate (DMAEMA), and acrylic acid (AA) were selected as the monomers for surface grafting of polymer chains/brushes via the atom transfer radical polymerization (ATRP) method. Thereafter, four nanofibrous membranes (i.e., RC, RC-poly(HEMA), RC-poly(DMAEMA), and RC-poly(AA)) were explored as innovative supports for immobilization of an enzyme of bovine liver catalase (CAT). The amount/capacity, activity, stability, and reusability of immobilized catalase were evaluated, and the kinetic parameters (Vmax and Km) for immobilized and free catalase were determined. The results indicated that the respective amounts/capacities of immobilized catalase on RC-poly(HEMA) and RC-poly(DMAEMA) nanofibrous membranes reached 78 ± 3.5 and 67 ± 2.7 mg g(-1), which were considerably higher than the previously reported values. Meanwhile, compared to that of free CAT (i.e., 18 days), the half-life periods of RC-CAT, RC-poly(HEMA)-CAT, RC-poly(DMAEMA)-CAT, and RC-poly(AA)-CAT were 49, 58, 56, and 60 days, respectively, indicating that the storage stability of immobilized catalase was also significantly improved. Furthermore, the immobilized catalase exhibited substantially higher resistance to temperature variation (tested from 5 to 70 °C) and lower degree of sensitivity to pH value (tested from 4.0 and 10.0) than the free catalase. In particular, according to the kinetic parameters of Vmax and Km, the nanofibrous membranes of RC-poly(HEMA) (i.e., 5102 μmol mg(-1) min(-1) and 44.89 mM) and RC-poly(DMAEMA) (i.e., 4651 μmol mg(-1) min(-1) and 46.98 mM) had the most satisfactory biocompatibility with immobilized catalase. It was therefore concluded that the electrospun RC nanofibrous membranes surface-grafted with 3-dimensional nanolayers of polymer chains/brushes would be

  13. A new method for cellulose membrane fabrication and the determination of its characteristics.

    PubMed

    Kuo, Yen-Ning; Hong, Juan

    2005-05-01

    A novel method to fabricate semipermeable cellulose membranes based on cellulose regeneration of a dry membrane cast by the neutralization reaction is presented in this paper. In this method, an environmentally acceptable cellulose dissolution procedure is employed to prepare the membrane casting solution comprised of microcrystalline cellulose dissolved in aqueous NaOH. Moreover, a new cast drying/cellulose regeneration technique is proposed and successfully applied to prepare membranes after the exploitation of the conventional immersion precipitation method, which results in the formation of granular cellulose particles rather than membranes due to the low cellulose concentration (<5 wt%) in the cast. In the present technique, the cellulose concentration in the membrane cast is dramatically increased through water evaporation, and glycerin is utilized in the cellulose regeneration process to achieve a gentle neutralization reaction. As a result, defect-free membranes with a uniform structure are developed. A detailed investigation is also presented concerning the effects of membrane forming parameters, i.e., the concentrations of cellulose, solvent, and acid, and the membrane thickness, on membrane properties. In addition, by coordinating the molecular separation experiments via the ultrafiltration process against a number of macromolecules with various molecular weights, the fabricated membranes are demonstrated to be capable of sieving molecules with a MW above 50,000.

  14. Bacterial Cellulose-Hydroxyapatite Nanocomposites for Bone Regeneration

    PubMed Central

    Saska, S.; Barud, H. S.; Gaspar, A. M. M.; Marchetto, R.; Ribeiro, S. J. L.; Messaddeq, Y.

    2011-01-01

    The aim of this study was to develop and to evaluate the biological properties of bacterial cellulose-hydroxyapatite (BC-HA) nanocomposite membranes for bone regeneration. Nanocomposites were prepared from bacterial cellulose membranes sequentially incubated in solutions of CaCl2 followed by Na2HPO4. BC-HA membranes were evaluated in noncritical bone defects in rat tibiae at 1, 4, and 16 weeks. Thermogravimetric analyses showed that the amount of the mineral phase was 40%–50% of the total weight. Spectroscopy, electronic microscopy/energy dispersive X-ray analyses, and X-ray diffraction showed formation of HA crystals on BC nanofibres. Low crystallinity HA crystals presented Ca/P a molar ratio of 1.5 (calcium-deficient HA), similar to physiological bone. Fourier transformed infrared spectroscopy analysis showed bands assigned to phosphate and carbonate ions. In vivo tests showed no inflammatory reaction after 1 week. After 4 weeks, defects were observed to be completely filled in by new bone tissue. The BC-HA membranes were effective for bone regeneration. PMID:21961004

  15. Thickness effect of kenaf cellulose membrane on its morphological, physical and tensile properties

    NASA Astrophysics Data System (ADS)

    Hashim, Sharifah Nurul Ain Syed; Zakaria, Sarani; Jaafar, Sharifah Nabihah Syed; Chia, Chin Hua

    2016-11-01

    Dissolution of kenaf core cellulose was undergone in NaOH/Urea solvent and the cellulose solution was casted with three different thicknesses (0.04 mm, 0.06 mm and 0.07 mm) followed by coagulation in 5 % of H2SO4 to form regenerated cellulose membrane. The XRD results showed that the crystallinity index (CrI) of kenaf core cellulose membrane decreased after been regenerated into cellulose II. The surface morphology showed that the pores of the membrane became smaller as the thickness of cellulose membrane increased. The transparency tests demonstrated the thinner samples (0.04 mm) gave higher light transmittance than the thickest samples (0.07 mm). The kenaf core membrane with 0.07 mm thickness possessed highest tensile strength and breaking elongation at σ = 33.48 and ɛ = 8.03 relatively and also exhibited the largest pore size.

  16. High-flux cellulose acetate membranes

    SciTech Connect

    Boeddeker, K.W.; Finken, H.; Wenzlaff, A.

    1981-01-01

    Three routes to increase the permeate flux of asymmetric cellulose diacetate membranes of the Loeb-Sourirajan type were investigated: increasing the hydrophilicity of the membranes; increasing their compaction stability, and employing a swelling agent which allows for higher solvent-to-polymer ratio in the casting solution. The effect of casting solution composition on flux and rejection of formamide-modified cellulose acetate membrane is included, illustrating the general capability of this membrane type as function of solvent concentration. Membranes of casting solution composition cellulose diacetate/acetone/formamide 23/52/25 were used as reference membranes in the work. 6 figures. (DP)

  17. Highly porous regenerated cellulose hydrogel and aerogel prepared from hydrothermal synthesized cellulose carbamate

    PubMed Central

    Gan, Sinyee; Chia, Chin Hua; Chen, Ruey Shan; Ellis, Amanda V.; Kaco, Hatika

    2017-01-01

    Here, a stable derivative of cellulose, called cellulose carbamate (CC), was produced from Kenaf (Hibiscus cannabinus) core pulp (KCP) and urea with the aid of a hydrothermal method. Further investigation was carried out for the amount of nitrogen yielded in CC as different urea concentrations were applied to react with cellulose. The effect of nitrogen concentration of CC on its solubility in a urea-alkaline system was also studied. Regenerated cellulose products (hydrogels and aerogels) were fabricated through the rapid dissolution of CC in a urea-alkaline system. The morphology of the regenerated cellulose products was viewed under Field emission scanning electron microscope (FESEM). The transformation of allomorphs in regenerated cellulose products was examined by X-ray diffraction (XRD). The transparency of regenerated cellulose products was determined by Ultraviolet–visible (UV–Vis) spectrophotometer. The degree of swelling (DS) of regenerated cellulose products was also evaluated. This investigation provides a simple and efficient procedure of CC determination which is useful in producing regenerated CC products. PMID:28296977

  18. Highly porous regenerated cellulose hydrogel and aerogel prepared from hydrothermal synthesized cellulose carbamate.

    PubMed

    Gan, Sinyee; Zakaria, Sarani; Chia, Chin Hua; Chen, Ruey Shan; Ellis, Amanda V; Kaco, Hatika

    2017-01-01

    Here, a stable derivative of cellulose, called cellulose carbamate (CC), was produced from Kenaf (Hibiscus cannabinus) core pulp (KCP) and urea with the aid of a hydrothermal method. Further investigation was carried out for the amount of nitrogen yielded in CC as different urea concentrations were applied to react with cellulose. The effect of nitrogen concentration of CC on its solubility in a urea-alkaline system was also studied. Regenerated cellulose products (hydrogels and aerogels) were fabricated through the rapid dissolution of CC in a urea-alkaline system. The morphology of the regenerated cellulose products was viewed under Field emission scanning electron microscope (FESEM). The transformation of allomorphs in regenerated cellulose products was examined by X-ray diffraction (XRD). The transparency of regenerated cellulose products was determined by Ultraviolet-visible (UV-Vis) spectrophotometer. The degree of swelling (DS) of regenerated cellulose products was also evaluated. This investigation provides a simple and efficient procedure of CC determination which is useful in producing regenerated CC products.

  19. Comparison of physical properties of regenerated cellulose films fabricated with different cellulose feedstocks in ionic liquid.

    PubMed

    Pang, JinHui; Wu, Miao; Zhang, QiaoHui; Tan, Xin; Xu, Feng; Zhang, XueMing; Sun, RunCang

    2015-05-05

    With the serious "white pollution" resulted from the non-biodegradable plastic films, considerable attention has been directed toward the development of renewable and biodegradable cellulose-based film materials as substitutes of petroleum-derived materials. In this study, environmentally friendly cellulose films were successfully prepared using different celluloses (pine, cotton, bamboo, MCC) as raw materials and ionic liquid 1-ethyl-3-methylimidazolium acetate as a solvent. The SEM and AFM indicated that all cellulose films displayed a homogeneous and smooth surface. In addition, the FT-IR and XRD analysis showed the transition from cellulose I to II was occurred after the dissolution and regeneration process. Furthermore, the cellulose films prepared by cotton linters and pine possessed the most excellent thermal stability and mechanical properties, which were suggested by the highest onset temperature (285°C) and tensile stress (120 MPa), respectively. Their excellent properties of regenerated cellulose films are promising for applications in food packaging and medical materials.

  20. Regenerating cellulose from ionic liquids for an accelerated enzymatic hydrolysis

    SciTech Connect

    Zhao, Hua; Jones, Cecil L; Baker, Gary A; Xia, Shuqian; Olubajo, Olarongbe; Person, Vernecia

    2009-01-01

    The efficient conversion of lignocellulosic materials into fuel ethanol has become a research priority in producing affordable and renewable energy. The pretreatment of lignocelluloses is known to be key to the fast enzymatic hydrolysis of cellulose. Recently, certain ionic liquids (ILs)were found capable of dissolving more than 10 wt% cellulose. Preliminary investigations [Dadi, A.P., Varanasi, S., Schall, C.A., 2006. Enhancement of cellulose saccharification kinetics using an ionic liquid pretreatment step. Biotechnol. Bioeng. 95, 904 910; Liu, L., Chen, H., 2006. Enzymatic hydrolysis of cellulose materials treated with ionic liquid [BMIM]Cl. Chin. Sci. Bull. 51, 2432 2436; Dadi, A.P., Schall, C.A., Varanasi, S., 2007. Mitigation of cellulose recalcitrance to enzymatic hydrolysis by ionic liquid pretreatment. Appl. Biochem. Biotechnol. 137 140, 407 421] suggest that celluloses regenerated from IL solutions are subject to faster saccharification than untreated substrates. These encouraging results offer the possibility of using ILs as alternative and nonvolatile solvents for cellulose pretreatment. However, these studies are limited to two chloride-based ILs: (a) 1-butyl-3-methylimidazolium chloride ([BMIM]Cl), which is a corrosive, toxic and extremely hygroscopic solid (m.p. 70 C), and (b) 1-allyl-3-methylimidazolium chloride ([AMIM]Cl), which is viscous and has a reactive side-chain. Therefore, more in-depth research involving other ILs is much needed to explore this promising pretreatment route. For this reason, we studied a number of chloride- and acetate-based ILs for cellulose regeneration, including several ILs newly developed in our laboratory. This will enable us to select inexpensive, efficient and environmentally benign solvents for processing cellulosic biomass. Our data confirm that all regenerated celluloses are less crystalline (58 75% lower) and more accessible to cellulase (>2 times) than untreated substrates. As a result, regenerated Avicel

  1. Regenerated cellulose/wool blend enhanced biomimetic hydroxyapatite mineralization.

    PubMed

    Salama, Ahmed; El-Sakhawy, Mohamed

    2016-11-01

    The current article investigates the effect of bioactive cellulose/wool blend on calcium phosphate biomimetic mineralization. Regenerated cellulose/wool blend was prepared by dissolution-regeneration of neat cellulose and natural wool in 1-butyl-3-methyl imidazolium chloride [Bmim][Cl], as a solvent for the two polymers. Crystalline hydroxyapatite nanofibers with a uniform size, shape and dimension were formed after immersing the bioactive blend in simulated body fluid. The cytotoxicity of cellulose/wool/hydroxyapatite was studied using animal fibroblast baby hamster kidney cells (BHK-21) and the result displayed good cytocompatability. This research work presents a green processing method for the development of novel cellulose/wool/hydroxyapatite hybrid materials for tissue engineering applications.

  2. Process of treating cellulosic membrane and alkaline with membrane separator

    NASA Technical Reports Server (NTRS)

    Hoyt, H. E.; Pfluger, H. L. (Inventor)

    1970-01-01

    The improvement of water-soluble cellulose ether membranes for use as separators in concentrated alkaline battery cells is discussed. The process of contacting membranes with an aqueous alkali solution of concentration less than that of the alkali solution to be used in the battery but above that at which the membrane is soluble is described.

  3. Reverse osmosis cellulose and cellulosic membranes prepared by repeated drying and rewetting

    SciTech Connect

    Black, L.E.; Wan, W.K.

    1989-08-15

    In a method for separating extraction solvents from extract of raffinate phases by selectively permeating the extraction solvent through a cellulose or cellulosic membrane under reverse conditions. This paper describes an improvement comprising using a cellulose or cellulosic membrane which has been dried, rewet and redried before being used to effect the desired separation.

  4. Regenerated cellulose fiber and film immobilized with lysozyme

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The present work reports an initial engineering approach for fabricating lysozyme-bound regenerated cellulose fiber and film. Glycine-esterified cotton was dissolved in an ionic liquid solvent 1–Butyl–3–methylimidazolium Chloride (BMIMCl) in which lysozyme was activated and covalently attached to c...

  5. Ca²+ sorption on regenerated cellulose fibres.

    PubMed

    Fitz-Binder, Christa; Bechtold, Thomas

    2012-10-01

    High calcium content in cellulose materials can cause considerable problems in pulp processing, textile chemical treatment and consumer use, e.g. dyeing operations or household laundry. The Ca(2+) binding capacity of cellulose also is of relevance in food and medical applications. Through their carboxyl group content regenerated cellulose fibres can act as weak anion exchangers, thus all types of regenerated cellulose fibres such as lyocell, viscose and modal fibres, show a distinct ability to bind Ca(2+) ions. The binding capacity is limited by the carboxyl group content, which was determined with 15 mmol/kg for lyocell fibres and 20 mmol/kg for viscose fibres, using the Methylene Blue sorption method. The presence of bound Ca(2+) also was demonstrated by complex formation with alizarin. The molar ratio between carboxylic group content and bound Ca(2+) ions was one Ca(2+) ion for a single carboxyl group. As a result of Ca(2+) sorption a positive net charge of the cellulose results and another anion has to be bound as counter ion for reasons of charge neutralisation. Results of potentiometric titrations indicate HCO(3)(-) to be present as counter ion in the Ca(2+) cellulose system. Thus under the experimental conditions studied, bound Ca(2+) is proposed to be present in the form COO(-)Ca(2+)HCO(3)(-).

  6. Nanofibrous microfiltration membrane based on cellulose nanowhiskers.

    PubMed

    Ma, Hongyang; Burger, Christian; Hsiao, Benjamin S; Chu, Benjamin

    2012-01-09

    A multilayered nanofibrous microfiltration (MF) membrane system with high flux, low pressure drop, and high retention capability against both bacteria and bacteriophages (a virus model) was developed by impregnating ultrafine cellulose nanowhiskers (diameter about 5 nm) into an electrospun polyacrylonitrile (PAN) nanofibrous scaffold (fiber diameter about 150 nm) supported by a poly(ethylene terephthalate) (PET) nonwoven substrate (fiber diameter about 20 μm). The cellulose nanowhiskers were anchored on the PAN nanofiber surface, forming a cross-linked nanostructured mesh with very high surface-to-volume ratio and a negatively charged surface. The mean pore size and pore size distribution of this MF system could be adjusted by the loading of cellulose nanowhiskers, where the resulting membrane not only possessed good mechanical properties but also high surface charge density confirmed by the conductivity titration and zeta potential measurements. The results indicated that a test cellulose nanowhisker-based MF membrane exhibited 16 times higher adsorption capacity against a positively charged dye over a commercial nitrocellulose-based MF membrane. This experimental membrane also showed full retention capability against bacteria, for example, E. coli and B. diminuta (log reduction value (LRV) larger than 6) and decent retention against bacteriophage MS2 (LRV larger than 2).

  7. Demonstration and Validation of a Regenerated-Cellulose Dialysis Membrane Diffusion Sampler for Monitoring Ground Water Quality and Remediation Progress at DoD Sites

    DTIC Science & Technology

    2007-01-01

    not equilibrate within 28 days. Equilibration times for selected explosive compounds through dialysis membranes were determined by LeBlanc... MEMBRANE DIFFUSION SAMPLER FOR MONITORING GROUND WATER QUALITY AND REMEDIATION PROGRESS AT DoD SITES (ER-0313) by Thomas E. Imbrigiotta... MEMBRANE DIFFUSION SAMPLER FOR MONITORING GROUND WATER QUALITY AND REMEDIATION PROGRESS AT DOD SITES (ER-0313) 6. AUTHOR(S) 5d. PROJECT NUMBER 5e

  8. Regenerated bacterial cellulose microfluidic column for glycoproteins separation.

    PubMed

    Chen, Chuntao; Zhu, Chunlin; Huang, Yang; Nie, Ying; Yang, Jiazhi; Shen, Ruiqi; Sun, Dongping

    2016-02-10

    To analysis and separate glycoproteins, a simple strategy to prepare regenerated bacterial cellulose (RBC) column with concanavalin A (Con A) lectin immobilized in microfluidic system was applied. RBC was filled into microchannel to fabricate RBC microcolumn after bacterial cellulose dissolved in NaOH-sulfourea water solution. Lectin Con A was covalently connected onto RBC matrix surface via Schiff-base formation. Lysozyme (non-glycoprotein) and transferrin (glycoprotein) were successfully separated based on their different affinities toward the immobilized Con A. Overall, the RBC microfluidic system presents great potential application in affinity chromatography of glycoproteins analysis, and this research represents a significant step to prepare bacterial cellulose (BC) as column packing material in microfluidic system. What is more, troublesome operations for lectin affinity chromatography were simplified by integrating the microfluidic chip onto a HPLC (High Performance Liquid Chromatography) system.

  9. Cellulosic ion-exchange membranes for hemodialysis.

    PubMed

    Mollison, A N; Graydon, W F

    1977-07-01

    The application of cellulosic ion-exchange membranes to hemodialysis was studied in vitro. The membranes were prepared by radiation-grafting methacrylic acid and vinylpyridine to films of DuPont cellophane PD-215 to produce cation-exchange and anion-exchange membranes, respectively. Solutions of urea, creatinine, glucose, and uric acid were studied for their interactions with and diffusion through the membranes. Ultrafiltration rates were also determined. Cuprophane and PD-215 cellophane were studied as controls. Dialysis plots for the membranes revealed a mechanism of "assisted transport." Initially, the solutes were removed from solution by a sorption/adsorption mechanism followed by a steady-state diffusion process. The calculated diffusivities for these later steady-state regions increased linearly with capacity for urea, creatinine, and uric acid, while for glucose the reverse was true. The combined processes involved provided considerably greater mass transport per unit thickness than either DuPont PD-215 cellophane or Cupropane.

  10. Highly ordered cellulose II crystalline regenerated from cellulose hydrolyzed by 1-butyl-3-methylimidazolium chloride.

    PubMed

    Ahn, Yongjun; Song, Younghan; Kwak, Seung-Yeop; Kim, Hyungsup

    2016-02-10

    This research focused on the preparation of highly ordered cellulose II crystalline by cellulose hydrolysis in ionic liquid, and the influence of molecular mobility on recrystallization of cellulose. The molar mass of cellulose was controlled by hydrolysis using 1-butyl-3-methylimidazolium chloride (BmimCl). The molecular mobility of cellulose dissolved in BmimCl was characterized by rheological properties. After characterization of cellulose solution and regeneration, change of molar mass and conversion to crystalline were monitored using gel-permeation chromatography and powder X-ray diffraction, respectively. The molar mass of the cellulose in BmimCl was remarkably decreased with an increase in duration time, resulting in better mobility and a lower conformational constraint below critical molar mass. The decrease in molar mass surprisingly increased the crystallinity up to ∼ 85%, suggesting a recrystallization rate dependence of the mobility. The correlation between the mobility and recrystallization rate represented quit different behavior above and below a critical molar mass, which strongly demonstrated to the effect of mobility on the conversion of amorphous state to crystalline structure.

  11. Evaluation of cellulose and carboxymethyl cellulose/poly(vinyl alcohol) membranes.

    PubMed

    Ibrahim, Maha M; Koschella, Andreas; Kadry, Ghada; Heinze, Thomas

    2013-06-05

    Cellulose was isolated from rice straw and converted to carboxymethyl cellulose (CMC). Both polymers were crosslinked with poly(vinyl alcholo) (PVA). The physical properties of the resulting membranes were characterized by FT-IR, TGA, DSC and SEM. The cellulose and CMC were first prepared from bleached rice straw pulp. The infrared spectroscopy of the resulting polymer membranes indicated a decrease in the absorbance of the OH group at 3300-3400 cm(-1), which is due to bond formation with either the cellulose or CMC with the PVA. The thermal stability of PVA/cellulose and PVA/CMC membranes was lower than PVA membrane. The surface of the resulting polymer membranes showed smooth surface in case of the PVA/CMC membrane and rough surface in case of the PVA/cellulose membrane. Desalination test, using 0.2% NaCl, showed that pure PVA membranes had no effect while membranes containing either cellulose or CMC as filler were able to decrease the content of the NaCl from the solution by 25% and 15%, respectively. Transport properties, including water and chloroform vapor were studied. The moisture transport was reduced by the presence of both cellulose and CMC. Moreover, the membranes containing cellulose and CMC showed significantly reduced flux compared to the pure PVA. The water sorption, solubility and soaking period at different pH solutions were also studied and showed that the presence of both cellulose and CMC influences the properties.

  12. Thin-film Nanofibrous Composite Membranes Containing Cellulose or Chitin Barrier Layers Fabricated by Ionic Liquids

    SciTech Connect

    H Ma; B Hsiao; B Chu

    2011-12-31

    The barrier layer of high-flux ultrafiltration (UF) thin-film nanofibrous composite (TFNC) membranes for purification of wastewater (e.g., bilge water) have been prepared by using cellulose, chitin, and a cellulose-chitin blend, regenerated from an ionic liquid. The structures and properties of regenerated cellulose, chitin, and a cellulose-chitin blend were analyzed with thermogravimetric analysis (TGA) and wide-angle X-ray diffraction (WAXD). The surface morphology, pore size and pore size distribution of TFNC membranes were determined by SEM images and molecular weight cut-off (MWCO) methods. An oil/water emulsion, a model of bilge water, was used as the feed solution, and the permeation flux and rejection ratio of the membranes were investigated. TFNC membranes based on the cellulose-chitin blend exhibited 10 times higher permeation flux when compared with a commercial UF membrane (PAN10, Sepro) with a similar rejection ratio after filtration over a time period of up to 100 h, implying the practical feasibility of such membranes for UF applications.

  13. Fabrication of flexible self-standing all-cellulose nanofibrous composite membranes for virus removal.

    PubMed

    Huang, Weijuan; Wang, Yixiang; Chen, Chao; Law, John Lok Man; Houghton, Michael; Chen, Lingyun

    2016-06-05

    All-cellulose nanocomposite membranes with excellent performance were successfully fabricated as novel filtration system to remove nanoparticles and virus from aqueous medium. These membranes were composed of two combined layers: an electrospun cellulose nanofabric layer treated by hot-pressing to provide mechanical support and a coating of regenerated cellulose gel with tiny inter-connected pores as barrier. Hot-pressing did not affect the fiber shape of electrospun nanofabrics, but significantly improved their mechanical properties due to increased hydrogen bonds. The regenerated cellulose gel formed a porous coating that tightly attached to electrospun nanofabrics, and its pore size varied depending on cellulose source, solution concentration, and drying process. By assembling these two layers together, the nanocomposite membranes showed the notable retention of negatively charged 100 nm latex beads (99.30%). Moreover, the electronegative nature of cellulose membranes imparted the rejection ratio of 100% and (98.68 ± 0.71)% against positively charged 50 nm latex beads and Hepatitis C Virus, respectively.

  14. Bacterial cellulose and bacterial cellulose-chitosan membranes for wound dressing applications.

    PubMed

    Lin, Wen-Chun; Lien, Chun-Chieh; Yeh, Hsiu-Jen; Yu, Chao-Ming; Hsu, Shan-Hui

    2013-04-15

    Bacterial cellulose (BC) and bacterial cellulose-chitosan (BC-Ch) membranes were successfully produced in large scale. BC was synthesized by Acetobacter xylinum. BC-Ch was prepared by immersing BC in chitosan followed by freeze-drying. The surface morphology of BC and BC-Ch membranes were examined by a scanning electron microscope (SEM). SEM images showed that BC-Ch possessed a denser fibril network with smaller pores than BC. Infrared spectroscopy was used to confirm the incorporation of chitosan in BC-Ch. The swelling behavior, water retention capacity, and mechanical properties of BC and BC-Ch were further evaluated. Results indicated that both membranes maintained proper moisture contents for an extensive period without dehydration. The tensile strength and elongation at break for BC-Ch were slightly lower while the Young's modulus was higher. Cell culture studies demonstrated that BC and BC-Ch had no cytotoxicity. In the antibacterial test, the addition of chitosan in BC showed significant growth inhibition against Escherichia coli and Staphylococcus aureus. The effects of BC and BC-Ch on skin wound healing were assessed by rat models. Histological examinations revealed that wounds treated with BC-Ch epithelialized and regenerated faster than those treated with BC or Tegaderm. Therefore, BC-Ch was considered as a potential candidate for wound dressing materials.

  15. Responsive behavior of regenerated cellulose in hydrolysis under microwave radiation.

    PubMed

    Ni, Jinping; Na, Haining; She, Zhen; Wang, Jinggang; Xue, Wenwen; Zhu, Jin

    2014-09-01

    This work studied the responsive behavior of regenerated cellulose (RC) in hydrolysis under microwave radiation. Four types of RC with different crystallinity (Cr) and degree of polymerization (DP) are produced to evaluate the reactivity of RC by step-by-step hydrolysis. Results show Cr is the key factor to affect the reactivity of RCs. With hydrolysis of amorphous region and the formation of recrystallization, the Cr of RC reaches a high value and thus weakens the reactivity. As a result, the increment of cellulose conversion and sugar yield gradually reduces. Decrease of the DP of RC is helpful to increase the speed at the onset of hydrolysis and produce high sugar yield. But, there is no direct influence with the reactivity of RC to prolong the time of pretreatment. This research provides an accurate understanding to guide the RC preparation for sugar formation with relative high efficiency under mild reaction conditions.

  16. Regenerated cellulose scaffolds: Preparation, characterization and toxicological evaluation.

    PubMed

    de Araújo Júnior, Adalberto M; Braido, Guilherme; Saska, Sybele; Barud, Hernane S; Franchi, Leonardo P; Assunção, Rosana M N; Scarel-Caminaga, Raquel M; Capote, Ticiana S O; Messaddeq, Younès; Ribeiro, Sidney J L

    2016-01-20

    Regenerated cellulose scaffolds (RCS) may be used as alloplastic materials for tissue repair. In this work, the RCS were obtained by viscose process and characterized by scanning electron microscopy (SEM), wide angle X-ray diffraction (WAXD), Fourier transform infrared spectroscopy (FTIR) and thermogravimetry analysis (TG). In vitro enzymatic degradation assay and toxicological assays were also evaluated. The physicochemical characterizations revealed the formation of a porous material with distinct thermal profile and crystallinity compared to pristine cellulose pulp. Enzymatic degradation assay revealed that lysozyme showed a mildest catalytic action when compared to cellulase, Tricoderma reesei (Tr). Nevertheless, both enzymes were efficient for degrading the RCS. RCS did not show cytotoxicity, mutagenic or genotoxic effects. The systematically characterization of this work suggests that RCS presented distinct features that make it a viable material for future studies related to the development of scaffolds for biological applications.

  17. Membranes for the Guided Bone Regeneration

    PubMed Central

    Lee, Sang-Woon; Kim, Seong-Gon

    2014-01-01

    Many kinds of membrane have been used for the guided bone regeneration (GBR) technique. However, most membranes do not fulfill all requirements for the ideal membrane for the GBR technique. Among them, collagen membrane has been most widely used. However, its high price and weak tensile strength in wet condition are limitations for wide clinical application. Synthetic polymers have also been used for the GBR technique. Recently, silk based membrane has been considered as a membrane for the GBR technique. Despite many promising preclinical data for use of a silk membrane, clinical data regarding the silk membrane has been limited. However, silk based material has been used clinically as vessel-tie material and an electrospun silk membrane was applied successfully to patients. No adverse effect related to the silk suture has been reported. Considering that silk membrane can be provided to patients at a cheap price, its clinical application should be encouraged. PMID:27489841

  18. Cellulose-Based Membranes for Solutes Fractionation

    NASA Astrophysics Data System (ADS)

    Anokhina, T. S.; Yushkin, A. A.; Volkov, V. V.; Antonov, S. V.; Volkov, A. V.

    This work was focused on investigation of industrial cellophane film as a membrane material for solvent nanofiltration. The effect of conditioning of cellophane membranes by stepwise changing of composition of ethanol-water binary mixtures (from ethanol to water and from water to ethanol) was studied. It was shown that such treatment leads to an increase of ethanol permeability more than two orders of magnitude over initial untreated film samples. Treated cellophane membranes possess the ethanol permeability coefficient comparable with the values for highly permeability glassy polymers. Investigation of cellophane swelling in water ethanol solutions allowed to conclude that during the treatment formation of porous in the film takes place due to increase of inter chain distances. Observed high ethanol permeability connected with the fact that formed porous structure remains after the replacement of water with ethanol. Also it was shown that rejection coefficients of a number of dyes (MW 350) were in good agreement with the degree of hydrophobicity/hydrophilicity and ability of the solvent to form hydrogen bonding with the solute molecules. It was demonstrated that cellulose-based membranes can be complimentary for other type of the membranes in fractionation of multi-components solutions.

  19. Characterization of cellulose membranes modified with luminescent silicon quantum dots nanoparticles.

    PubMed

    Campos, B B; Gelde, L; Algarra, M; Esteves da Silva, J C G; Vázquez, M I; Benavente, J

    2016-10-20

    A highly hydrophilic planar membrane fabricated with regenerated cellulose (RC-4 membrane), a biocompatible polymer, was modified by inclusion of water-soluble silicon quantum dot nanoparticles (SiQDs). Both bare SiQDs and SiQDs coated with a PAMAM-OH dendrimer were employed in order to obtain luminescent and thermally stable membrane systems (RC-4/SiQDs and RC-4/SiQDs-PAMAM-OH membranes). Original and SiQDs-modified membranes were characterized by fluorescence spectroscopy (steady and confocal), derivative thermogravimetric analysis and impedance spectroscopy measurements. According to these results, both SiQDs-regenerated cellulose composite membranes present luminescent character as well as higher thermal resistance and conductivity than the original sample, although the dendrimer coverage of the SiQDs might partially shield such effects. Moreover, the permanence of SiQDs nanoparticles in the structure of the cellulosic support in aqueous environments and their effect on diffusive transport were determined by water uptake as well as by membrane potential measurements at different concentrations of a model electrolyte (KCl). These results demonstrate the possible use of these stable nano-engineered membranes, which are based on SiQDs nanoparticles, in electrochemical devices under flow conditions.

  20. Characterization of cellulose II nanoparticles regenerated from ionic liquid, 1-butyl-3-methylimidazolium chloride

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Regenerated cellulose nanoparticles (RCNs) including both elongated fiber and spherical structures were prepared from microcrystalline cellulose (MCC)and cotton using 1-butyl-3-methylimidazolium chloride followed by high-pressure homogenization. The crystalline structure of RCNs was cellulose II in ...

  1. Guided Bone Regeneration with Novel Bioabsorbable Membranes

    NASA Astrophysics Data System (ADS)

    Koyama, Yoshihisa; Kikuchi, Masanori; Yamada, Takeki; Kanaya, Tomohiro; Matsumoto, Hiroko N.; Takakuda, Kazuo; Miyairi, Hiroo; Tanaka, Junzo

    Guided Bone Regeneration (GBR) is a method for bone tissue regeneration. In this method, membranes are used to cover bone defects and to block the invasion of the surrounding soft tissues. It would provide sufficient time for the osteogenic cells from bone marrow to proliferate and form new bony tissues. In spite of the potential usefulness of this method, no appropriate materials for the GBR membrane have been developed. Here we design the ideal mechanical properties of the GBR membranes and created novel materials, which is the composite of β-tricalcium phosphate and block copolymer of L-lactide, glycolide and ɛ-caplolactone. In the animal experiments with the use of the trial products, we observed significant enhancement in the bone regeneration and proved the effectiveness of the materials.

  2. Crystallographic snapshot of cellulose synthesis and membrane translocation

    PubMed Central

    Morgan, Jacob L.W.; Strumillo, Joanna; Zimmer, Jochen

    2012-01-01

    Cellulose, the most abundant biological macromolecule, is an extracellular, linear polymer of glucose molecules. It represents an essential component of plant cell walls but is also found in algae and bacteria. In bacteria, cellulose production frequently correlates with the formation of biofilms, a sessile, multicellular growth form. Cellulose synthesis and transport across the inner bacterial membrane is mediated by a complex of the multi-spanning catalytic BcsA subunit and the membrane-anchored, periplasmic BcsB protein. Here we present the crystal structure of a complex of BcsA and BcsB from Rhodobacter sphaeroides containing a translocating polysaccharide. The structure of the BcsA-B translocation intermediate reveals the architecture of the cellulose synthase, demonstrates how BcsA forms a cellulose-conducting channel, and suggests a model for the coupling of cellulose synthesis and translocation in which the nascent polysaccharide is extended by one glucose molecule at a time. PMID:23222542

  3. Impact of regeneration process on the crystalline structure and enzymatic hydrolysis of cellulose obtained from ionic liquid.

    PubMed

    Cao, Xuefei; Peng, Xinwen; Sun, Shaoni; Zhong, Linxin; Wang, Sha; Lu, Fachuang; Sun, Runcang

    2014-10-13

    The present study investigated the impact of regeneration process on the crystalline structure and enzymatic hydrolysis behaviors of microcrystalline cellulose (MCC) regenerated from ionic liquid 1-butyl-3-methylimidazolium chloride. The crystalline structures of these regenerated samples were analyzed by X-ray diffraction. Results suggested that almost amorphous cellulose was obtained by regenerating MCC in acetone (DRC-a), while partial cellulose II structure could be found in these regenerated samples from water and ethanol. Additionally, the enzymatic hydrolysis behaviors of MCC and its regenerated samples were comparatively studied. Results showed that above 90% of cellulose could be converted into glucose within 4h for DRC-a and regenerated cellulose without drying (WRC-w) as compared to that of MCC (9.7%). Therefore, the regeneration process could significantly influence the crystallinity and digestibility of cellulose.

  4. Perselectivity of porous cellulose nitrate membranes in evapomeation with temperature difference

    SciTech Connect

    Uragami, T.; Komatsu, R.; Miyata, T.

    1995-12-01

    Ethanol-permselectivity from aqueous ethanol solutions through porous cellulose nitrate membranes was investigated by evaporation with temperature difference under various conditions. On the other hand, same experiments using porous cellulose acetate were carried out. From these results of porous cellulose nitrate and cellulose acetate membranes, mechanism of permeation and separation for ethanol-permselectivity through cellulose nitrate membranes is discussed from viewpoints of physical and chemical structures of porous cellulose ester membranes.

  5. Quartz crystal microbalance with dissipation monitoring and surface plasmon resonance studies of carboxymethyl cellulose adsorption onto regenerated cellulose surfaces.

    PubMed

    Liu, Zelin; Choi, Heejun; Gatenholm, Paul; Esker, Alan R

    2011-07-19

    Adsorption of anionic polyelectrolytes, sodium salts of carboxymethyl celluloses (CMCs) with different degrees of substitution (DS = 0.9 and 1.2), from aqueous electrolyte solutions onto regenerated cellulose surfaces was studied using quartz crystal microbalance with dissipation monitoring (QCM-D) and surface plasmon resonance (SPR) experiments. The influence of both calcium chloride (CaCl(2)) and sodium chloride (NaCl) on CMC adsorption was examined. The QCM-D results demonstrated that CaCl(2) (divalent cation) caused significantly greater CMC adsorption onto regenerated cellulose surfaces than NaCl (monovalent cation) at the same ionic strength. The CMC layers adsorbed onto regenerated cellulose surfaces from CaCl(2) solutions exhibited greater stability upon exposure to flowing water than layers adsorbed from NaCl solutions. Both QCM-D and SPR results showed that CMC adsorption onto regenerated cellulose surfaces from CaCl(2) solutions increased with increasing CaCl(2) concentration up to the solubility limit (10 mM). Voigt-based viscoelastic modeling of the QCM-D data indicated that the CMC layers adsorbed onto regenerated cellulose surfaces had shear viscosities of η(f) ≈ 10(-3) N·s·m(-2) and elastic shear moduli of μ(f) ≈ 10(5) N·m(-2). Furthermore, the combination of SPR spectroscopy and QCM-D showed that the CMC layers contained 90-95% water. Adsorption isotherms for CMCs in CaCl(2) solutions were also obtained from QCM-D and were fit by Freundlich isotherms. This study demonstrated that CMC adsorption from CaCl(2) solutions is useful for the modification of cellulose surfaces.

  6. Aqueous alkali metal hydroxide insoluble cellulose ether membrane

    NASA Technical Reports Server (NTRS)

    Hoyt, H. E.; Pfluger, H. L. (Inventor)

    1969-01-01

    A membrane that is insoluble in an aqueous alkali metal hydroxide medium is described. The membrane is a resin which is a water-soluble C2-C4 hydroxyalkyl cellulose ether polymer and an insolubilizing agent for controlled water sorption, a dialytic and electrodialytic membrane. It is particularly useful as a separator between electrodes or plates in an alkaline storage battery.

  7. Granuloma Due to Oxidized Regenerated Cellulose in an Aged Rhesus Macaque (Macaca mulatta)

    PubMed Central

    Lemoy, Marie-Josee MF; Schouten, Angela Colagross; Canfield, Don R

    2016-01-01

    Bioabsorbable hemostatic agents such as oxidized regenerated cellulose are widely used to control intraoperative diffuse capillary bleeding. Compared with electrocautery or ligation, oxidized regenerated cellulose has the advantage of controlling bleeding without occluding the vessel lumen or causing thermal injuries to adjacent tissue. Although the manufacturer recommends removal of the material once hemostasis is achieved, oxidized regenerated cellulose is a bioabsorbable hemostatic agent and is often left in the surgical bed to prevent subsequent bleeding after surgical closure. However, noninvasive imaging techniques have revealed granulomatous foreign-body reactions that mimic infection or tumor recurrence. We present a case report of sterile peritonitis and granuloma formation secondary to the presence of oxidized regenerated cellulose after intestinal resection to excise a colonic adenocarcinoma in an aged rhesus macaque. PMID:26884411

  8. Tensile and characterization properties of regenerated cellulose empty fruit bunch biocomposite films using ionic liquid

    NASA Astrophysics Data System (ADS)

    Husseinsyah, Salmah; Zailuddin, Nur Liyana Izyan; Li, Chew Li; Mostapha @ Zakaria, Marliza

    2016-07-01

    The regenerated cellulose (RC) empty fruit bunch (EFB) biocomposite films were prepared using ionic liquid. The tensile strength and modulus of elasticity of regenerated cellulose biocomposite films achieved maximum value at 2 wt% of EFB contents while at 3 and 4 wt% of EFB the tensile strength and modulus of elasticity tend to decreased. The elongation at break tends to decreased at 2 wt% of EFB content but increased at 3 and 4 wt% of EFB contents. The crystallinity index reaches maximum at 2 wt% EFB content, followed by declination with further addition of EFB content. The morphology study illustrated that regenerated cellulose biocomposite films at 2 wt% of EFB contents exhibit a smooth surface that suggested the reinforcement was surrounded by the regenerated cellulose matrix, while at 4 wt% EFB content shows a rough morphology.

  9. Novel membrane for guided bone regeneration.

    PubMed

    Pirhonen, E M; Pohjonen, T H; Weber, F E

    2006-09-01

    Membranes have been clinically used for guided tissue and bone regeneration for decades, but their use in every day clinical practice is rather limited. We developed a biodegradable membrane (InionGTR) composed of polylactide, polyglycolide and trimethylene carbonate aiming to improve the properties of membrane. Before application the membrane is treated with N-methyl-pyrrolidone (NMP) to achieve a rubber like consistency, to allow easy handling and manageability in the clinical setting. After placing the membrane NMP diffuses out from the polymer phase into the water phase. The loss of NMP in the polymer stiffens the membrane up and allows space maintenance in the defect area. In addition the influx and efflux of NMP creates a porous surface on the membrane leading to an improved integration of tissues into the porous surface layers of the InionGTR membrane. Therefore, the use of NMP improves the handling in the clinical setting, and allows tissue integration and space maintenance, both important for the outcome of the treatment.

  10. Influence of coagulation concentration on properties of regenerated kenaf core membranes produced in NaOH/urea aqueous solution

    NASA Astrophysics Data System (ADS)

    Azahari, Nor Aziawati; Jaafar, Sharifah Nabihah Syed; Zakaria, Sarani

    2016-11-01

    Cellulose was extracted from kenaf core pulp by a series of bleaching processes and subsequently dissolved using an alkaline NaOH/urea solvent at low temperature. The produced cellulose solution was coagulated with H2SO4 at concentration from 5 to 12 wt% to produce a series of regenerated cellulose (RC) membranes. The surface morphology, structure and physical properties of the membranes were measured with variable pressure scanning electron microscope (VPSEM), X-ray diffraction (XRD), UV-vis spectrophotometer and tensile testing. The results from VPSEM revealed that the pore size of the membranes changed as a function of the concentration of H2SO4 coagulant. RC membranes coagulated with relatively dilute H2SO4 solution exhibited better mechanical properties. Thus, this work provided a promising way to prepare cellulose membranes with different pore sizes and good physical properties.

  11. Structure and permeation properties of cellulose esters asymmetric membranes.

    PubMed

    Stamatialis, D F; Dias, C R; de Pinho, M N

    2000-01-01

    The permeation properties of a series of membranes of cellulose esters, presenting a wide range of characteristics, were studied and correlated to the structure of water in the pores, to the polymer hydrophilicity/hydrophobicity, and to the morphology of the surface of the active layer. Asymmetric membranes of cellulose acetate, cellulose acetate propionate, and cellulose acetate butyrate were prepared by the phase inversion method and their preferential permeation performance tested. The surface morphology and the structure of the water in the pores of the active layer were studied by atomic force microscopy (AFM) and attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy, respectively. Results show that higher rejection to NaCl and low fluxes are generally associated with smaller clusters of water in the pores. On the other hand, the surface of the membranes presenting smaller clusters of water in the active layer show generally surfaces with lower roughness as measured by AFM.

  12. Facile approach for the dispersion of regenerated cellulose in aqueous system in the form of nanoparticles.

    PubMed

    Adsul, Mukund; Soni, Sarvesh K; Bhargava, Suresh K; Bansal, Vipul

    2012-09-10

    This study reports a facile method to disperse cellulose in deionized water, wherein a critical condition of regenerated cellulose is discovered, where it completely disperses up to a maximum of 5 g L(-1) concentration in deionized water with the help of ultrasonication. The dispersed cellulose is characterized by TEM and DLS, the latter among which shows 200 nm hydrodynamic radii of cellulose nanoparticles dispersed in deionized water. FTIR analysis of dispersed cellulose reveals that dispersed cellulose losses its crystallinity during regeneration and dispersion step employed in this study. The dispersed cellulose reported in this study is able to form free-standing, transparent films, which were characterized by SEM, XRD, TGA, EDX, and FTIR spectroscopy and show resistance against dissolution in water. Additionally, the dispersed cellulose is able to undergo at least three times faster enzymatic hydrolysis in comparison to pristine microcrystalline cellulose under similar reaction conditions. The dispersed cellulose reported here could be a better material for reinforcement, preparation of hydrogels, and drug delivery applications under physiological environment.

  13. Ketotifen controlled release from cellulose acetate propionate and cellulose acetate butyrate membranes.

    PubMed

    Sobral, Manuela C C M; Sobral, Abilio J F N; Guthrie, J T; Gil, M H

    2008-02-01

    Ketotifen was immobilised in cellulose acetate propionate (CAP) membranes and in cellulose acetate butyrate (CAB) membranes. The characteristics of each system were evaluated under a range of experimental conditions. The topography and uniformity of the membranes was assessed using scanning electron microscopy. The release characteristics associated with Ketotifen were monitored spectrophotometrically. The swelling capacity of the membranes was evaluated and attributed to the combined effects of diffusion and of complex dissociation, during swelling. The materials produced were able to provide controlled release of Ketotifen due to their controlled swelling behaviour and adequate release properties. The results showed that the release of Ketotifen from the CAB membranes is higher but the release from the CAP membranes is more uniform.

  14. Using absorbable collagen membranes for guided tissue regeneration, guided bone regeneration, and to treat gingival recession.

    PubMed

    Wang, H L; Carroll, W J

    2000-05-01

    This article reviews the role of barrier membranes in guided tissue regeneration (GTR) and guided bone regeneration (GBR), including the advantages of using absorbable barrier membranes in GTR and GBR and the unique properties of collagen membranes. The indications and contraindications for using collagen membranes for these procedures are examined, and successful cases are presented. Finally, the role of collagen membranes in the future of regenerative therapy is considered.

  15. Taste sensing with polyacrylic acid grafted cellulose membrane.

    PubMed

    Majumdar, Sarmishtha; Dey, Joykrishna; Adhikari, Basudam

    2006-03-15

    There are reports of fabrication of taste sensor by adsorbing lipids into Millipore filter paper, which improved the taste sensing efficiency of membrane remarkably. We have made an attempt to prepare taste sensor material by grafting polyacrylic acid (PAA) to cellulose. The research work covers polymer membrane preparation, morphology study, and structural characterization of the membrane and study of the taste sensing characteristics of this membrane for five different taste substances. FTIR spectroscopic analysis and SEM were done to get an idea about the structure and morphology of the PAA grafted cellulose membrane. Surface charge density of the membrane was estimated. The sensor characteristics like temporal stability, response stability, response to different taste substances, and reproducibility of sensing performance were studied using PAA grafted cellulose membrane. Sensor device prepared with this membrane has shown distinct response patterns for different taste substances in terms of membrane potential. Threshold concentrations of PAA grafted cellulose membrane for HCl, NaCl, quinine-hydrochloride (Q-HCl), sucrose and monosodium glutamate are 0.001 mM, 0.01 mM, 0.08 mM, 0.08 mM and 0.01 mM, respectively. The threshold concentrations except that in Q-HCl are below human threshold concentrations. Membranes also showed characteristic response patterns for organic acids like acetic acid, citric acid, formic acid, etc., mineral acids like HCl, H(2)SO(4) and HNO(3), etc., salts, bitter substances, sweet substances and umami substances. Sensor device prepared with this membrane has excellent shelf life.

  16. Characterization of Cellulose regenerated from solutions of pine and eucalyptus woods in 1-allyl-3-methilimidazolium chloride.

    PubMed

    Casas, A; Alonso, M V; Oliet, M; Santos, T M; Rodriguez, F

    2013-02-15

    Cellulose is currently separated from lignocellulosic materials using non-environmentally friendly processes. The development of new methods for treating biomass and separating cellulose remains a challenge and would be very useful in the context of the biorefinery philosophy. In this work, cellulose has been regenerated from solutions of Pinus radiata and Eucalyptus globulus woods in 1-allyl-3-methylimidazolium chloride. Wood dissolution was performed in a microwave oven at 120 °C for 20 min. Cellulose was characterized and compared to the reference material, microcrystalline cellulose (MCC). Regenerated celluloses showed lower crystallinity and thermal stability than MCC, although the ash contents at 400 °C were higher than in MCC. The regenerated celluloses were obtained without lignin and almost free from hemicellulose. Furthermore, cellulose was not significantly degraded in the dissolution process of both woods. The insoluble solids showed higher content of lignin and hemicellulose than the raw materials.

  17. Development of Cellulose/PVDF-HFP Composite Membranes for Advanced Battery Separators

    NASA Astrophysics Data System (ADS)

    Castillo, Alejandro; Agubra, Victor; Alcoutlabi, Mataz; Mao, Yuanbing

    Improvements in battery technology are necessary as Li-ion batteries transition from consumer electronic to vehicular and industrial uses. An important bottle-neck in battery efficiency and safety is the quality of the separators, which prevent electric short-circuits between cathode and anode, while allowing an easy flow of ions between them. In this study, cellulose acetate was dissolved in a mixed solvent with poly(vinylpyrrolidone) (PVP), and the mixture was forcespun in a peudo paper making process to yield nanofibrillated nonwoven mats. The mats were soaked in NaOH/Ethanol to strip PVP and regenerate cellulose from its acetate precursor. The cellulose mats were then dipped in poly(vinylidenefluoride-co-hexafluoropropylene) (PVDF-HFP) to yield the cellulose/PVDF-HFP composte membranes. These membranes were characterized chemically through FTIR spectroscopy and solvent-stability tests, thermally through DSC, physically by stress/strain measurements along with weight-based electrolyte uptake, and electrically by AC-impedance spectroscopy combined with capacitative cycling.

  18. Regenerated cellulose fibers spun-dyed with carbon black/latex composite dispersion.

    PubMed

    Wang, Chunxia; Du, Changsen; Tian, Anli; Fu, Shaohai; Xu, Changhai

    2014-01-30

    A carbon black (CB)/latex composite was prepared by the method of miniemulsion polymerization for use as a colorant for spun dyeing of regenerated cellulose fibers. Analysis of experimental results revealed that the CB/latex composite had a small particle size and a narrow particle size distribution which were important to ensure a stable dispersion being later added to spinning solution. A good stability of the prepared CB/latex composite dispersion in the spinning solution indicated that it was highly possible to use the CB/latex composite as a colorant for spun dyeing of regenerated cellulose fibers. When a 3.5% mass ratio of CB/latex composite to cellulose was used for spun dyeing, the spun-dyed fibers had the highest tensile strength, breaking elongation and color strength. The rubbing and washing color fastnesses of spun-dyed regenerated cellulose fibers could satisfy requirements of most textiles. This study provided a new insight into producing spun-dyed regenerated cellulose with a novel colorant.

  19. Highly Porous Regenerated Cellulose Fiber Mats via the Co-Forcespinning of Cellulose Acetate for Separator Applications

    NASA Astrophysics Data System (ADS)

    Castillo, Alejandro; Mao, Yuanbing

    2015-03-01

    Improvements in battery technology are necessary for the transition away from a fossil fuel based economy. An important bottle-neck in battery efficiency is the quality of the separator, which separates the cathode and anode to prevent a short-circuit while still allowing the ions in solution to flow as close to unabated as possible. In this work solutions of cellulose acetate, polyvinyldiflourine (pvdf), and polyvinylpyrrolidone (pvp) dissolved in a 2:1 v/v acetone/dimethylacetamide solvent mixture were Forcespun to create nonwoven fiber mats of nanoscale diameter. These mats were then soaked in a NaOH solution so as to both strip the pvp from the fiber as well as regenerate cellulose from its acetate derivative for the purpose of creating high surface area, nanoporous, hydrophilic, and ioniclly conductive cellulose/pvdf nonwoven mats for the purposes of testing their suitability as battery separators

  20. High-flux Thin-film Nanofibrous Composite Ultrafiltration Membranes Containing Cellulose Barrier Layer

    SciTech Connect

    Ma, H.; Yoon, K; Rong, L; Mao, Y; Mo, Z; Fang, D; Hollander, Z; Gaiteri, J; Hsiao , B; Chu, B

    2010-01-01

    A novel class of thin-film nanofibrous composite (TFNC) membrane consisting of a cellulose barrier layer, a nanofibrous mid-layer scaffold, and a melt-blown non-woven substrate was successfully fabricated and tested as an ultrafiltration (UF) filter to separate an emulsified oil and water mixture, a model bilge water for on-board ship bilge water purification. Two ionic liquids: 1-butyl-3-methylimidazolium chloride and 1-ethyl-3-methylimidazolium acetate, were chosen as the solvent to dissolve cellulose under mild conditions. The regenerated cellulose barrier layer exhibited less crystallinity (determined by wide-angle X-ray diffraction, WAXD) than the original cotton linter pulps, but good thermal stability (determined by thermal gravimetric analysis, TGA). The morphology, water permeation, and mechanical stability of the chosen TFNCmembranes were thoroughly investigated. The results indicated that the polyacrylonitrile (PAN) nanofibrous scaffold was partially imbedded in the cellulose barrier layer, which enhanced the mechanical strength of the top barrier layer. The permeation flux of the cellulose-based TFNCmembrane was significantly higher (e.g. 10x) than comparable commercial UFmembranes (PAN10 and PAN400, Sepro) with similar rejection ratios for separation of oil/water emulsions. The molecular weight cut-off (MWCO) of TFNC membranes with cellulose barrier layer was evaluated using dextran feed solutions. The rejection was found to be higher than 90% with a dextran molecular weight of 2000 KDa, implying that the nominal pore size of the membrane was less than 50 nm. High permeation flux was also observed in the filtration of an emulsified oil/water mixture as well as of a sodium alginate aqueous solution, while high rejection ratio (above 99.5%) was maintained after prolonged operation. A variation of the barrier layer thickness could dramatically affect the permeation flux and the rejection ratio of the TFNCmembranes, while different sources of cellulose

  1. Production and characterization of bacterial cellulose membranes with hyaluronic acid from chicken comb.

    PubMed

    de Oliveira, Sabrina Alves; da Silva, Bruno Campos; Riegel-Vidotti, Izabel Cristina; Urbano, Alexandre; de Sousa Faria-Tischer, Paula Cristina; Tischer, Cesar Augusto

    2017-04-01

    The bacterial cellulose (BC), from Gluconacetobacter hansenii, is a biofilm with a high degree of crystallinity that can be used for therapeutic purposes and as a candidate for healing wounds. Hyaluronic acid (HA) is a constitutive polysaccharide found in the extracellular matrix and is a material used in tissue engineering and scaffolding for tissue regeneration. In this study, polymeric composites were produced in presence of hyaluronic acid isolated from chicken comb on different days of fermentation, specifically on the first (BCHA-SABT0) and third day (BCHA-SABT3) of fermentation. The structural characteristics, thermal stability and molar mass of hyaluronic acid from chicken comb were evaluated. Native membrane and polymeric composites were characterized with respect to their morphology and crystallinity. The optimized process of extraction and purification of hyaluronic acid resulted in low molar mass hyaluronic acid with structural characteristics similar to the standard commercial hyaluronic acid. The results demonstrate that the polymeric composites (BC/HA-SAB) can be produced in situ. The membranes produced on the third day presented better incorporation of HA-SAB between cellulose microfiber, resulting in membranes with higher thermal stability, higher roughness and lower crystallinity. The biocompatiblily of bacterial cellulose and the importance of hyaluronic acid as a component of extracellular matrix qualify the polymeric composites as promising biomaterials for tissue engineering.

  2. Chitosan as a barrier membrane material in periodontal tissue regeneration.

    PubMed

    Xu, Chun; Lei, Chang; Meng, Liuyan; Wang, Changning; Song, Yaling

    2012-07-01

    Periodontal regeneration is defined as regeneration of the tooth-supporting tissues including cementum, periodontal ligament, and alveolar bone. Guided tissue regeneration (GTR) has been demonstrated to be an effective technique to achieve periodontal regeneration. In the GTR procedures, various kinds of membranes play important roles. Chitosan, a deacetylated derivative of chitin, is biocompatible, biodegradable, and antimicrobial. It acts as hydrating agent and possesses tissue healing and osteoinducing effect. Chitosan can be easily processed into membranes, gels, nanofibers, beads, nanoparticles, scaffolds, and sponges forms and can be used in drug delivery systems. Here, we review the bioproperties of chitosan and report the progress of application of chitosan as membranes in GTR and guided bone regeneration (GBR), which indicates that chitosan could be a good substrate candidate as the materials for the GTR/GBR membranes.

  3. Grafting of carboxybetaine brush onto cellulose membranes via surface-initiated ARGET-ATRP for improving blood compatibility.

    PubMed

    Wang, Miao; Yuan, Jiang; Huang, Xiaobo; Cai, Xianmei; Li, Li; Shen, Jian

    2013-03-01

    Grafting-from has proven to be a very effective way to create high grafting densities and well-controlled polymer chains on different kinds of surfaces. In this work, we aim to graft zwitterionic brush from cellulose membrane (CM) via ARGET-ATRP (Activator Regenerated by Electron Transfer ATRP) method indirectly for blood compatibility improvement. Characterization of the CM substrates before and after modification was carried out by attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR), water contact angle measurements, X-ray photoelectron spectroscopy analysis, and atomic force microscopy, respectively. The results demonstrated zwitterionic brushes were successfully grafted on the CM surfaces, and the content of the grafted layer increased gradually with the polymerization time. The platelet adhesion, hemolytic test and plasma protein adsorption results indicated the cellulose membrane had significantly excellent blood compatibility featured on lower platelet adhesion and protein adsorption without causing hemolysis. The functionalized cellulose substrate could have a great potential usage for biomedical applications.

  4. Regenerable Polyelectrolyte Membrane for Ultimate Fouling Control in Forward Osmosis.

    PubMed

    Kang, Yan; Zheng, Sunxiang; Finnerty, Casey; Lee, Michael J; Mi, Baoxia

    2017-03-02

    This study demonstrated the feasibility of using regenerable polyelectrolyte membranes to ultimately control the irreversible membrane fouling in a forward osmosis (FO) process. The regenerable membrane was fabricated by assembling multiple polyethylenimine (PEI) and poly(acrylic acid) (PAA) bilayers on a polydopamine-functionalized polysulfone support. The resulting membrane exhibited higher water flux and lower solute flux in FO mode (with the active layer facing feed solution) than in PRO mode (with the active layer facing draw solution) using trisodium citrate as draw solute, most likely due to the unique swelling behavior of the polyelectrolyte membrane. Membrane regeneration was conducted by first dissembling the existing PEI-PAA bilayers using strong acid and then reassembling fresh PEI-PAA bilayers on the membrane support. It was found that, after the acid treatment, the first covalently bonded PEI layer and some realigned PAA remained on the membrane support, acting as a beneficial barrier that prevented the acid-foulant mixture from penetrating into the porous support during acid treatment. The water and solute flux of the regenerated membrane was very similar to that of the original membrane regardless of alginate fouling, suggesting an ultimate solution to eliminating the irreversible membrane fouling in an FO process. With a procedure similar to the typical membrane cleaning protocol, in situ membrane regeneration is not expected to noticeably increase the membrane operational burden but can satisfactorily avoid the expensive replacement of the entire membrane module after irreversible fouling, thereby hopefully reducing the overall cost of the membrane-based water-treatment system.

  5. Surface modification of silica- and cellulose-based microfiltration membranes with functional polyamino acids for heavy metal sorption

    SciTech Connect

    Ritchie, S.M.C.; Bhattacharyya, D.; Bachas, L.G.; Olin, T.; Sikdar, S.K.

    1999-09-14

    Functionalized membranes represent a field with multiple applications. Examination of specific metal-macromolecule interactions on these surfaces presents an excellent method for characterization of these materials. These interactions may also be exploited for heavy metal sorption from drinking and industrial water sources. Various low-capacity, silica-based ion-exchange and chelating sorbents (about 0.5 mmol of metal/g or resin) are available for treatment of such waters. Cellulosic membrane-based sorbents, functionalized with polyamino acids, present an excellent approach for high-capacity (3--14 mmol of metal/g or sorbent) metal sorption. Silica-based membrane sorbents posses metal sorption capacities approaching those of cellulosic-based membranes, with the added benefits of excellent acid and solvent resistance. Metal sorption capacities of silica-based membrane sorbents possess metal sorption capacities approaching those of cellulosic-based membranes, with the added benefits of excellent acid and solvent resistance. Metal sorption capacities of silica-based membrane sorbents with various polyamino acids range from 0.6 mmol to 1.4 mmol of metal/g of sorbent. Ion exchange, chelation, and electrostatic interactions form the basis of metal sorption. Electrostatic interactions are greatly magnified in membrane-based sorbents, and are partly responsible for their high capacities. Regeneration of these sorbents has also been shown, including the possibility for selective desorption of metals.

  6. Hydrolysis behavior of regenerated celluloses with different degree of polymerization under microwave radiation.

    PubMed

    Ni, Jinping; Teng, Na; Chen, Haizhen; Wang, Jinggang; Zhu, Jin; Na, Haining

    2015-09-01

    This work studied the hydrolysis behavior of regenerated celluloses (RCs) with different degree of polymerization (DP) by using the catalyst of dilute acid under microwave radiation. Results showed that the DP had a considerable influence on hydrolysis of cellulose. The reactivity of RCs was significantly improved when DP was lower than 51. The highest sugar yield of 59.2% was achieved from RC with lowest DP of 23 at 160 °C for 15 min. But the lowest yield of 32.6% was obtained when RC with highest DP of 132 was used. Recrystallization of cellulose was found to hinder the further hydrolysis particularly with the high DP. The effect of recrystallization can be reduced by the decrease of DP of RCs. This research demonstrates that the DP of RCs plays a crucial role on hydrolysis and it provides a preliminary guide based on DP to find a suitable pretreatment method for cellulose hydrolysis.

  7. Ultrasound influence upon calcium carbonate precipitation on bacterial cellulose membranes.

    PubMed

    Stoica-Guzun, Anicuta; Stroescu, Marta; Jinga, Sorin; Jipa, Iuliana; Dobre, Tanase; Dobre, Loredana

    2012-07-01

    The effect of ultrasonic irradiation (40 kHz) on the calcium carbonate deposition on bacterial cellulose membranes was investigated using calcium chloride (CaCl(2)) and sodium carbonate (Na(2)CO(3)) as starting reactants. The composite materials containing bacterial cellulose-calcium carbonate were characterized by means of scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and color measurements. The polymorphs of calcium carbonate that were deposited on bacterial cellulose membranes in the presence or in the absence of ultrasonic irradiation were calcite and vaterite. The morphology of the obtained crystals was influenced by the concentration of starting solutions and by the presence of ultrasonic irradiation. In the presence of ultrasonic irradiation the obtained crystals were bigger and in a larger variety of shapes than in the absence of ultrasounds: from cubes of calcite to spherical and flower-like vaterite particles. Bacterial cellulose could be a good matrix for obtaining different types of calcium carbonate crystals.

  8. Hematopoiesis on cellulose ester membranes (CEM). X. Effects of in vitro irradiation of stromal cells prior to application on CEM

    SciTech Connect

    Knospe, W.H.; Husseini, S.G.

    1986-11-01

    Cellulose ester membranes (CEM) were coated with stromal cells from murine bone or bone marrow irradiated in vitro with 1000, 2000, or 4000 rad and then implanted i.p. in CAF1 mice for periods of six and 12 months. CEM coated with stromal cells from bone showed excellent regeneration of bone and hematopoiesis after 1000 rad in vitro irradiation. After 2000 rad, hematopoietic and bone regeneration was reduced by about 50%, and after 4000 rad it was completely absent in CEM coated with stromal cells from bone. CEM coated with stromal cells from bone marrow showed no regeneration of hematopoiesis or bone after 1000, 2000, and 4000 rad in vitro irradiation and residence i.p. for six and 12 months. These results indicate that regeneration of the hematopoietic microenvironment is dependent upon living stromal cells. A difference in radiation sensitivity is demonstrated between stromal cells from bone and from bone marrow.

  9. Allergic contact dermatitis to regenerated oxidized cellulose contained in a matrix employed for wound therapy.

    PubMed

    Foti, Caterina; Bonamonte, Domenico; Conserva, Anna; Angelini, Gianni

    2007-07-01

    We describe a case of a 40-year-old non-atopic woman with recurrent leg ulcers because of the factor V Leiden mutation who developed a severe eczematous lesions of the skin surrounding an ulcer of the right leg after the use of a protease-modulating matrix (Promogran, Johnson and Johnson, Gargrave, Skipton, UK). The patient was patch tested with the SIDAPA (Italian Society of Allergological, Occupational and Environmental Dermatology) standard series, a piece of the device as is, of the bovine collagen (Zyderm, Collagen Corporation, Palo Alto, CA, USA) as is, a piece of the gauze containing only regenerated oxidized cellulose (Tabotamp, Johnson and Johnson, Gargrave, North Yorkshire, UK) and of a fold towels in pure cellulose (Foscart, Bassano del Grappa, Italy). Patch tests gave a positive reactions to nickel sulphate and Promogran as is. We showed that the sensitizing agent was regenerated oxidized cellulose, a substance the treatment of ulcers and as is in and in combination with collagen in surgery for intraoperative hemostasis. The case reported suggests that regenerated oxidized cellulose can cause allergic contact dermatitis.

  10. Silk fibroin membrane used for guided bone tissue regeneration.

    PubMed

    Cai, Yurong; Guo, Junmao; Chen, Cen; Yao, Chenxue; Chung, Sung-Min; Yao, Juming; Lee, In-Seop; Kong, Xiangdong

    2017-01-01

    With the aim to develop a novel membrane with an appropriate mechanical property and degradation rate for guided bone tissue regeneration, lyophilized and densified silk fibroin membrane was fabricated and its mechanical behavior as well as biodegradation property were investigated. The osteoconductive potency of the silk fibroin membranes were evaluated in a defect rabbit calvarial model. Silk fibroin membrane showed the modulated biodegradable and mechanical properties via ethanol treatment with different concentration. The membrane could prevent soft tissue invasion from normal tissue healing, and the amounts of new bone and defect closure with silk fibroin membrane were similar to those of commercially available collagen membrane.

  11. Comparison of treatment efficiency of submerged nanofiltration membrane bioreactors using cellulose triacetate and polyamide membrane.

    PubMed

    Choi, J H; Fukushi, K; Yamamoto, K

    2005-01-01

    This study evaluates the performance of nanofiltration membrane bioreactor (NF MBR) systems using cellulose triacetate (CA) and polyamide (PA) membranes. The results indicated that both NF membranes could produce high quality permeate in the submerged NF MBR system. In addition, hollow fiber CA membranes exhibited the capability of higher permeate productivity than PA membranes. However, to obtain high quality permeate for a long-term operation, CA membranes should be maintained using an appropriate method, such as chlorine disinfection, in order to control the membrane biodegradation. The results demonstrated that PA membranes were capable of producing higher quality permeate for a long period than CA membranes. In order to enhance the practicability of PA membranes in submerged NF MBR systems, it is required that the membranes should have the lowest possible intrinsic salt rejection.

  12. Dissolution and regeneration of hide powder/cellulose composite in Gemini imidazolium ionic liquid.

    PubMed

    Wang, Guowei; Guo, Jiarong; Zhuang, Linghua; Wang, Yan; Xu, Bin

    2015-05-01

    Gemini imidazolium ionic liquid, 3,3'-[1,2-ethanediylbis (oxy-2,1-ethanediyl)]-bis[1-methyl-imidazolium]-dibromide ([C6O2(mim)2][Br]2), was used for the dissolution and regeneration of white hide powder (from pigskin), and blend white hide powder with cellulose for the easy production of white hide powder/cellulose composite. Dissolution performance of white hide powder in [C6O2(mim)2][Br]2 was studied. The native white hide powder and [C6O2(mim)2][Br]2 regenerated white hide powder were characterized by FT-IR, XRD, DSC-TG and FE-SEM. The results showed that [C6O2(mim)2][Br]2 was a good solvent to white hide powder. The dissolution time was 55 min when the white hide powder was 8% at 120°C. The dissolution time of [C6O2(mim)2][Br]2 for white hide powder was shorter than those of common ionic liquids. The triple helical structure of white hide powder was partly destroyed during [C6O2(mim)2][Br]2 dissolution. The possible mechanism of white hide powder dissolution in [C6O2(mim)2][Br]2 and the regeneration of white hide powder in methanol had been proposed. White hide powder/cellulose composites were successfully dissolved in [C6O2(mim)2][Br]2. The performance of white hide powder/cellulose film was measured by FT-IR and TG. The tensile strength, and elongation at break of white hide powder/cellulose composite films were tested. This work demonstrated that the white hide powder/cellulose composite exhibited some potential in collagen-based tissue engineering.

  13. Cellulose as Sustainable Materials for Separation Membranes

    NASA Astrophysics Data System (ADS)

    Chu, Benjamin

    2013-03-01

    Polysaccharides, while complex, form one of the most abundant sustainable resources on earth. We want to take advantage of fundamental advances in materials understanding across length and time scales to investigate the interrelationships between structure, morphology, processing, properties, performance, and cost to meet the specific challenges arising from separation membranes for water purification. Non-woven fiber mats have unique properties, such as interconnected pores, a very large surface-to-volume ratio, and a high capacity for surface modifications. The breakthrough concept of combining fibrous mats composed of different fiber diameters for fabricating scaffolds as a unique platform for water purification is presented. Further, we take advantage of recent advances in chemical modifications, structural studies using synchrotron X-rays, and physical scale-up transformations to drastically improve filtration membrane development. Support of this work by the NSF, ONR, NIH and Stony Brook Univ. is gratefully acknowledged. The Chu/Hsiao group on water purification includes Profs. B.S.Hsiao and C.Burger, Drs. H-Y.Ma, D-F.Fang, R.Wang, and grad students: X.Wang, Z. Wang, Y.Su, R. Yang

  14. Ion selective permeation through cellulose acetate membranes in forward osmosis.

    PubMed

    Irvine, Gavin J; Rajesh, Sahadevan; Georgiadis, Michael; Phillip, William A

    2013-12-03

    Solute-solute interactions can have a dramatic impact on the permeation of solutes through dense polymeric membranes. In particular, understanding how solute-solute interactions can affect the design of osmotically driven membrane processes (ODMPs) is critical to the successful development of these emerging water treatment and energy generation processes. In this work, we investigate the influence that solute-solute interactions have on nitrate permeation through an asymmetric cellulose acetate forward osmosis membrane. A series of experiments that included systematic modifications to the cation paired with nitrate, the identity of the draw solute, and the solution pH were conducted. These experiments reveal that in the unique operating geometry of ODMPs, where solute containing solutions are present on both sides of the membrane, nitrate fluxes are significantly higher (>15 times in some cases) than predicted by existing models for solute permeation in ODMPs. The identity of the cation paired with nitrate influences the flux of nitrate; the identity of the cation in the draw solution does not affect the flux of nitrate; however, the identity of the anion in the draw solution has the most significant impact on the flux of nitrate. These results suggest that an ion exchange mechanism, which allows nitrate to switch rapidly with anions from the draw solution, is present when cellulose acetate based membranes are used in ODMPs.

  15. Freeze gelated porous membranes for periodontal tissue regeneration.

    PubMed

    Qasim, Saad B; Delaine-Smith, Robin M; Fey, Tobias; Rawlinson, Andrew; Rehman, Ihtesham Ur

    2015-09-01

    Guided tissue regeneration (GTR) membranes have been used for the management of destructive forms of periodontal disease as a means of aiding regeneration of lost supporting tissues, including the alveolar bone, cementum, gingiva and periodontal ligaments (PDL). Currently available GTR membranes are either non-biodegradable, requiring a second surgery for removal, or biodegradable. The mechanical and biofunctional limitations of currently available membranes result in a limited and unpredictable treatment outcome in terms of periodontal tissue regeneration. In this study, porous membranes of chitosan (CH) were fabricated with or without hydroxyapatite (HA) using the simple technique of freeze gelation (FG) via two different solvents systems, acetic acid (ACa) or ascorbic acid (ASa). The aim was to prepare porous membranes to be used for GTR to improve periodontal regeneration. FG membranes were characterized for ultra-structural morphology, physiochemical properties, water uptake, degradation, mechanical properties, and biocompatibility with mature and progenitor osteogenic cells. Fourier transform infrared (FTIR) spectroscopy confirmed the presence of hydroxyapatite and its interaction with chitosan. μCT analysis showed membranes had 85-77% porosity. Mechanical properties and degradation rate were affected by solvent type and the presence of hydroxyapatite. Culture of human osteosarcoma cells (MG63) and human embryonic stem cell-derived mesenchymal progenitors (hES-MPs) showed that all membranes supported cell proliferation and long term matrix deposition was supported by HA incorporated membranes. These CH and HA composite membranes show their potential use for GTR applications in periodontal lesions and in addition FG membranes could be further tuned to achieve characteristics desirable of a GTR membrane for periodontal regeneration.

  16. Rheology of lyocell solutions from different cellulosic sources and development of regenerated cellulosic microfibers

    NASA Astrophysics Data System (ADS)

    Li, Zuopan

    2003-10-01

    The primary goals of the study were to develop manufactured cellulosic fibers and microfibers from wood pulps as well as from lignocellulosic agricultural by-products and to investigate alternative cellulosic sources as raw materials for lyocell solutions. A protocol was developed for the lyocell preparation from different cellulose sources. The cellulose sources included commercial dissolving pulps, commercial bleached hardwood, unbleached hardwood, bleached softwood, unbleached softwood, bleached thermomechanical pulp, unbleached thermomechanical pulp, bleached recycled newsprint, unbleached recycled newsprint, bagasse and kudzu. The rheological behavior of solutions was characterized. Complex viscosities and effective elongational viscosities were measured and the influences of parameters such as cellulose source, concentration, bleaching, and temperature were studied. One-way ANOVA post hoc tests were carried out to identify which cellulose sources have the potential to produce lyocell solutions having similar complex viscosities to those from commercial dissolving pulps. Lyocell solutions from both bleached and unbleached softwood and hardwood were classified as one homogenous subset that had the lowest complex viscosity. Kudzu solutions had the highest complex viscosity. The results showed the potential to substitute DP 1457 dissolving pulp with unbleached recycled newsprint pulps, to substitute DP 1195 dissolving pulp with bleached and unbleached thermomechanical pulps, to substitute DP 932 dissolving pulp with bleached thermomechanical pulps or bleached recycled newsprint pulps, to substitute DP 670 dissolving pulp with bagasse. Lyocell fibers were produced from selected solutions and were treated to produce microfibers. Water, sulfuric acid solutions and sodium hydroxide solutions were used. The treatment of lyocell fibers in 17.5% NaOH solutions for five minutes at 20°C successfully broke the fibers into fibrils along fiber axis. The diameters of the

  17. Regeneration of Aqueous Periodate Solutions by Ozone Treatment: A Sustainable Approach for Dialdehyde Cellulose Production.

    PubMed

    Koprivica, Slavica; Siller, Martin; Hosoya, Takashi; Roggenstein, Walter; Rosenau, Thomas; Potthast, Antje

    2016-04-21

    A method for easy and fast regeneration of aqueous periodate solutions from dialdehyde cellulose (DAC) production by ozone treatment is presented, along with a direct and reliable simultaneous quantification of iodate and periodate by reversed-phase HPLC. The influence of iodate and ozone concentration, solution pH, and reaction time on the regeneration efficiency was studied, as well as the reaction kinetics. Regeneration of spent periodate solutions by ozone was successfully performed in alkaline medium, which favors the formation of free (.) OH radicals, as supported by the addition of radical scavengers and quantum mechanical calculations. At pH 13 and an ozone concentration of approximately 150 mg L(-1) , periodate was completely regenerated from a 100 mm solution of iodate within 1 h at room temperature. A cyclic process of cellulose oxidation and subsequent regeneration of spent periodate with 90 % efficiency has been developed. So far, commercial applications of DAC have been hampered by difficulties in reusing the costly periodate. This work overcomes this hurdle and presents a highly efficient, clean, and low-cost protocol for the preparation of DAC with integrated periodate recycling, with the possibility of scaling the process up.

  18. Effect of acid hydrolysis on regenerated kenaf core membrane produced using aqueous alkaline-urea systems.

    PubMed

    Padzil, Farah Nadia Mohammad; Zakaria, Sarani; Chia, Chin Hua; Jaafar, Sharifah Nabihah Syed; Kaco, Hatika; Gan, Sinyee; Ng, Peivun

    2015-06-25

    Bleached kenaf core pulps (BKC) were hydrolyzed in H2SO4 (0.5M) at different time (0min to 90min) at room temperature. After the hydrolysis process, the viscosity average molecular weight (Mŋ) for BKC sample has reduced from 14.5×10(4) to 2.55×10(4). The hydrolyzed BKC was then dissolved in NaOH:urea:water and in LiOH:urea:water mixed solvent at the ratio of 7:12:81 and 4.6:15:80.4, respectively. The increased in hydrolysis time has decreased Mŋ of cellulose leading to easy dissolution process. Higher porosity and transparency with lower crystallinity index (CrI) of regenerated membrane produced can be achieved as the Mŋ reduced. The properties of membrane were observed through FESEM, UV-vis spectrophotometer and XRD. This study has proven that acid hydrolysis has reduced the Mŋ of cellulose, thus, enhanced the properties of regenerated membrane produced with assisted by alkaline/urea system.

  19. Collagen based barrier membranes for periodontal guided bone regeneration applications.

    PubMed

    Sheikh, Zeeshan; Qureshi, Javairia; Alshahrani, Abdullah M; Nassar, Heba; Ikeda, Yuichi; Glogauer, Michael; Ganss, Bernhard

    2017-01-01

    Certain cell populations within periodontal tissues possess the ability to induce regeneration, provided they have the opportunity to populate the wound or defect. Guided regeneration techniques have been investigated for regenerating periodontal tissues and such therapies usually utilize barrier membranes. Various natural and synthetic barrier membranes have been fabricated and tested to prevent epithelial and connective tissue cells from invading while allowing periodontal cells to selectively migrate into the defect. This paper focuses on the literature relevant to the use and potential of resorbable collagen membranes in GBR procedures, sites of periodontal and intrabony defects, in cases of socket and alveolar ridge preservation and at implant sites. The results of their use in GBR procedures has shown them to be effective and comparable with non-resorbable membranes with regards to clinical attachment gain, probing depth reduction and defect bone filling. They have also shown to prevent epithelial ingrowth into the defect space during the initial wound healing phase postsurgically. Collagen membranes have also been used for root coverage and GBR procedures and have shown good success rates comparable to subepithelial connective tissue grafts and expanded-polytetrafluoroethylene (e-PTFE) membranes. The future for periodontal tissue engineering is very exciting with the use of barrier membranes expected to continue playing a critical role. However, long-term clinical trials are required to further evaluate and confirm the efficacy of the available collagen barrier membranes for periodontal and bone regeneration use.

  20. Demonstration and Validation of a Regenerated Cellulose Dialysis Membrane Diffusion Sampler for Monitoring Ground Water Quality and Remediation Progress at DoD Sites for Perchlorate and Explosives Compounds (ER-0313)

    DTIC Science & Technology

    2010-09-30

    24  5.5.1 Field Demonstration Preparation and Mobilization ...1701. 4 2.0 TECHNOLOGY 2.1 TECHONOLOGY DESCRIPTION Most of the diffusion membrane samplers developed to date involve suspending a container...and Mobilization Access to and integrity of the wells to be sampled at each field demonstration site was checked one month prior to the start of the

  1. Detection of Escherichia coli in Foods: Indole Staining Methods for Cellulosic and Polysulfone Membrane Filters

    PubMed Central

    Sharpe, Anthony N.; Peterkin, Pearl I.; Rayman, M. Khalil

    1981-01-01

    Optimized procedures for staining Escherichia coli colonies on cellulosic and polysulfone membrane filters are described. An explanation for the behavior of the Ehrlich reaction on membrane filters is suggested. Images PMID:6166249

  2. Biodegradability of regenerated cellulose films coated with polyurethane/natural polymers interpenetrating polymer networks

    SciTech Connect

    Zhang, L.; Zhou, J.; Huang, J.; Gong, P. Zhou, Q.; Zheng, L.; Du, Y.

    1999-11-01

    Interpenetrating polymer network (IPN) coatings synthesized from castor-oil-based polyurethane (PU) with chitosan, nitrocellulose, or elaeostearin were coated on regenerated cellulose (RC) film for curing at 80--100 C for 2--5 min, providing biodegradable, water-resistant cellulose films coded, respectively, as RCCH, RCNC, and RCEs. The coated films were buried in natural soil for decaying and inoculated with a spore suspension of fungi on the agar medium, respectively, to test biodegradability. The viscosity-average molecular weight, M{sub {eta}}, and the weight of the degraded films decreased sharply with the progress of degradation. The degradation half-lifes, t{sub 1/2}, of the films in soil at 30 C were found to be 19 days for RC, 25 days for RCNC, 32 days for RCCH, and 45 days for the RCEs films. Scanning electron microscopy (SEM) showed that the extent of decay followed in the order RC {gt} RCNC {gt} RCCH {gt} RCEs. SEM, infrared (IR), high-performance liquid chromatography (HPLC), and CO{sub 2} evolution results indicated that the microorganisms directly attacked the water-resistant coating layer and then penetrated into the cellulose to speedily metabolize, while accompanying with producing CO{sub 2}, H{sub 2}O, glucose cleaved from cellulose, and small molecules decomposed from the coatings.

  3. Rheological and mechanical study of regenerated cellulose/multi-walled carbon nanotube composites

    NASA Astrophysics Data System (ADS)

    Shao, Wei; Wang, Shuxia; Liu, Hui; Wu, Jimin; Huang, Min; Ma, Wenjing; Huang, Chaobo

    2016-09-01

    Regenerated cellulose (RC)-based composites reinforced with multi-walled carbon nanotubes (MWCNTs) were prepared by a facile casting method. The morphology and microstructure of the fabricated composites were characterized using transmission electron microscopy, Fourier transform infrared spectroscopy (FTIR) and Raman spectroscopy. Thermogravimetry and derivative thermogravimetric analysis were conducted to investigate the effect of MWCNTs on the thermal behaviors of the RC. The results showed that the introduction of MWCNTs enhanced the thermal stability of the RC. Moreover, the effect of the dispersion state of MWCNTs in microcrystalline cellulose/ZnCl2 solutions with varying MWCNT loadings was studied by rheological tests. The mechanical properties of composite films were remarkably improved compared to those of pure RC film. Specifically, the composite film containing 3 wt% of MWCNTs exhibits a 123% enhancement in tensile strength and a 163% enhancement in the Young’s modulus compared with the pure RC film.

  4. CELLULOSE SYNTHASE INTERACTIVE1 Is Required for Fast Recycling of Cellulose Synthase Complexes to the Plasma Membrane in Arabidopsis

    PubMed Central

    Lei, Lei; Bashline, Logan; Li, Shundai

    2015-01-01

    Plants are constantly subjected to various biotic and abiotic stresses and have evolved complex strategies to cope with these stresses. For example, plant cells endocytose plasma membrane material under stress and subsequently recycle it back when the stress conditions are relieved. Cellulose biosynthesis is a tightly regulated process that is performed by plasma membrane-localized cellulose synthase (CESA) complexes (CSCs). However, the regulatory mechanism of cellulose biosynthesis under abiotic stress has not been well explored. In this study, we show that small CESA compartments (SmaCCs) or microtubule-associated cellulose synthase compartments (MASCs) are critical for fast recovery of CSCs to the plasma membrane after stress is relieved in Arabidopsis thaliana. This SmaCC/MASC-mediated fast recovery of CSCs is dependent on CELLULOSE SYNTHASE INTERACTIVE1 (CSI1), a protein previously known to represent the link between CSCs and cortical microtubules. Independently, AP2M, a core component in clathrin-mediated endocytosis, plays a role in the formation of SmaCCs/MASCs. Together, our study establishes a model in which CSI1-dependent SmaCCs/MASCs are formed through a process that involves endocytosis, which represents an important mechanism for plants to quickly regulate cellulose synthesis under abiotic stress. PMID:26443667

  5. Biocompatibility and functional performance of a polyethylene glycol acid-grafted cellulosic membrane for hemodialysis.

    PubMed

    Sirolli, V; Di Stante, S; Stuard, S; Di Liberato, L; Amoroso, L; Cappelli, P; Bonomini, M

    2000-06-01

    In order to improve the biochemical reactivity of the cellulose polymer, which is mainly attributed to the presence of surface hydroxyl groups, derivatized cellulosic membranes have been engineered replacing or masking some or all of the hydroxyl groups in the manufacturing process of the membrane. The present study was set up to analyze both biocompatibility and functional performance of two different derivatized cellulosic membranes (cellulose diacetate; polyethylene glycol, PEG, acid-grafted cellulose) as compared to a synthetic membrane (polymethylmethacrylate, PMMA). Cellulose diacetate is prepared by substituting hydroxyl groups with acetyl groups; PEG cellulose is obtained by grafting PEG chains onto the cellulosic polymer with a smaller amount of substitution than cellulose diacetate. While the three dialyzers provided similar urea and creatinine removal, the dialyzer containing cellulose diacetate showed a reduced ability to remove 32-microglobulin compared to that containing PEG cellulose or PMMA. A transient reduction in leukocyte count was observed for both derivatized cellulosic membranes. The neutrophil and monocyte counts throughout the entire dialysis session showed a closer parallelism with the cellular expression of the adhesive receptor CD 15s (sialyl-Lewis x molecule) than with CD11b/CD18 expression. Platelet activation, as indicated by the percentage of cells expressing the activation markers CD62P (P-selectin) and CD63 (gp53), occurred with all membranes at 15 min of dialysis and also with PMMA at 30 min. An increased formation of platelet-neutrophil and platelet-monocyte coaggregates was found at 15 and 30 min during dialysis with cellulose diacetate and PMMA but not with PEG cellulose. Generally in concomitance with the increase in platelet-neutrophil coaggregates, an increased hydrogen peroxide production by neutrophils occurred. Our results indicate that derivatizing cellulose may represent a useful approach to improve the biocompatibility

  6. Novel silk protein barrier membranes for guided bone regeneration.

    PubMed

    Smeets, Ralf; Knabe, Christine; Kolk, Andreas; Rheinnecker, Michael; Gröbe, Alexander; Heiland, Max; Zehbe, Rolf; Sachse, Manuela; Große-Siestrup, Christian; Wöltje, Michael; Hanken, Henning

    2016-10-12

    This study assesses the biocompatibility of novel silk protein membranes with and without modification, and evaluates their effect on facilitating bone formation and defect repair in guided bone regeneration. Two calvarian bone defects 12 mm in diameter were created in each of a total of 38 rabbits. Four different types of membranes, (silk-, hydroxyapatite-modified silk-, β-TCP-modified silk- and commonly clinically used collagen-membranes) were implanted to cover one of the two defects in each animal. Histologic analysis did not show any adverse tissue reactions in any of the defect sites indicating good biocompatibility of all silk protein membranes. Histomorphometric and histologic evaluation revealed that collagen and β-TCP modified silk membranes supported bone formation (collagen: bone area fraction p = 0.025; significant; β-TCP modified silk membranes bone area fraction: p = 0.24, not significant), guided bone regeneration and defect bridging. The bone, which had formed in defects covered by β-TCP modified silk membranes, displayed a more advanced stage of bone tissue maturation with restoration of the original calvarial bone microarchitecture when compared to the bone which had formed in defects, for which any of the other test membranes were used. Micro-CT analysis did not reveal any differences in the amount of bone formation between defects with and without membranes. In contrast to the collagen membranes, β-TCP modified silk membranes were visible in all cases and may therefore be advantageous for further supporting bone formation beyond 10 weeks and preventing soft tissue ingrowth from the periphery. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2016.

  7. Membranes for Periodontal Regeneration--A Materials Perspective.

    PubMed

    Bottino, Marco C; Thomas, Vinoy

    2015-01-01

    Periodontitis is a chronic inflammatory disorder affecting nearly 50% of adults in the United States. If left untreated, it can lead to the destruction of both soft and mineralized tissues that constitute the periodontium. Clinical management, including but not limited to flap debridement and/or curettage, as well as regenerative-based strategies with periodontal membranes associated or not with grafting materials, has been used with distinct levels of success. Unquestionably, no single implantable biomaterial can consistently guide the coordinated growth and development of multiple tissue types, especially in very large periodontal defects. With the global aging population, it is extremely important to find novel biomaterials, particularly bioactive membranes and/or scaffolds, for guided tissue (GTR) and bone regeneration (GBR) to aid in the reestablishment of the health and function of distinct periodontal tissues. This chapter offers an update on the evolution of biomaterials (i.e. membranes and bioactive scaffolds) as well as material-based strategies applied in periodontal regeneration. The authors start by providing a brief summary of the histological characteristics and functions of the periodontium and its main pathological condition, namely periodontitis. Next, a review of commercially available GTR/GBR membranes is given, followed by a critical appraisal of the most recent advances in the development of bioactive materials that enhance the chance for clinical success of periodontal tissue regeneration.

  8. Evaluation of microvolume regenerated cellulose (RC) microdialysis fibers for the sampling and detection of ammonia in air.

    PubMed

    Tang, Hao; Thompson, Jonathan E

    2010-06-15

    We have explored use of perfused regenerated cellulose (RC) microdialysis tubing (216microm o.d./200microm i.d.) as sampling probes for gaseous ammonia. The probes functioned by allowing the gas to diffuse through the permeable membrane into a stream of de-ionized water which continually perfused the tubing at 10-20microLmin(-1). The resulting ammonium in the perfusate was determined through a fluorimetric method (OPA-sulfite) with LED excitation at lambda(ex)=365+/-10nm and measurement of fluorescence emission at lambda(em)=425+/-20nm. By shielding the sampling membrane with a Plexiglas tube purged under laminar flow conditions, the potential interference of particulate ammonium depositing on the probe was minimized. The RC microdialysis tube was found to act as an efficient sampling device since it exhibits a very high surface-area-to-volume ratio (approximately 200cm(2)mL(-1)). As a result, aqueous concentrations of >100microM NH(4)(+) per ppm NH(3) (g) have been observed. In addition, the fluorogenic OPA-sulfite reaction is demonstrated to be very selective for ammonia over amines that have been measured in the atmosphere. This feature of the derivatization chemistry allows analysis of ammonia by fluorimetry without need for a separation step. The method developed has been applied to field measurements of ammonia at a swine barn facility with quantitative results agreeing with a reference method.

  9. Latent progenitor cells as potential regulators for tympanic membrane regeneration

    NASA Astrophysics Data System (ADS)

    Kim, Seung Won; Kim, Jangho; Seonwoo, Hoon; Jang, Kyung-Jin; Kim, Yeon Ju; Lim, Hye Jin; Lim, Ki-Taek; Tian, Chunjie; Chung, Jong Hoon; Choung, Yun-Hoon

    2015-06-01

    Tympanic membrane (TM) perforation, in particular chronic otitis media, is one of the most common clinical problems in the world and can present with sensorineural healing loss. Here, we explored an approach for TM regeneration where the latent progenitor or stem cells within TM epithelial layers may play an important regulatory role. We showed that potential TM stem cells present highly positive staining for epithelial stem cell markers in all areas of normal TM tissue. Additionally, they are present at high levels in perforated TMs, especially in proximity to the holes, regardless of acute or chronic status, suggesting that TM stem cells may be a potential factor for TM regeneration. Our study suggests that latent TM stem cells could be potential regulators of regeneration, which provides a new insight into this clinically important process and a potential target for new therapies for chronic otitis media and other eardrum injuries.

  10. Cellulose reinforced nylon-6 nanofibrous membrane: Fabrication strategies, physicochemical characterizations, wicking properties and biomimetic mineralization.

    PubMed

    Joshi, Mahesh Kumar; Tiwari, Arjun Prasad; Maharjan, Bikendra; Won, Ko Sung; Kim, Han Joo; Park, Chan Hee; Kim, Cheol Sang

    2016-08-20

    The aim of the present study is to develop a facile, efficient approach to reinforce nylon 6 (N6) nanofibers with cellulose chains as well as to study the effect that cellulose regeneration has on the physicochemical properties of the composite fibers. Here, a cellulose acetate (CA) solution (17wt%) was prepared in formic acid and was blended with N6 solution (20%, prepared in formic acid and acetic acid) in various proportions, and the blended solutions were then electrospun to produce hybrid N6/CA nanofibers. Cellulose was regenerated in-situ in the fiber via alkaline saponification of the CA content of the hybrid fiber, leading to cellulose-reinforced N6 (N6/CL) nanofibers. Electron microscopy studies suggest that the fiber diameter and hence pore size gradually decreases as the mass composition of CA increases in the electrospinning solution. Cellulose regeneration showed noticeable change in the polymorphic behavior of N6, as observed in the XRD and IR spectra. The strong interaction of the hydroxyl group of cellulose with amide group of N6, mainly via hydrogen bonding, has a pronounced effect on the polymorphic behavior of N6. The γ-phase was dominant in pristine N6 and N6/CA fibers while α- phase was dominant in the N6/CL fibers. The surface wettability, wicking properties, and the tensile stress were greatly improved for N6/CL fibers compared to the corresponding N6/CA hybrid fibers. Results of DSC/TGA revealed that N6/CL fibers were more thermally stable than pristine N6 and N6/CA nanofibers. Furthermore, regeneration of cellulose chain improved the ability to nucleate bioactive calcium phosphate crystals in a simulated body fluid solution.

  11. Physical properties and biocompatibility of cellulose/soy protein isolate membranes coagulated from acetic aqueous solution.

    PubMed

    Luo, Li-Hua; Wang, Xiao-Mei; Zhang, Yu-Feg; Liu, Yong-Ming; Chang, Peter R; Wang, Yan; Chen, Yun

    2008-01-01

    A series of cellulose/soy protein isolate (SPI) membranes was prepared from cellulose and SPI solution by casting and coagulation from 5 wt% acetic acid and 5 wt% sulphuric acid aqueous solution, respectively. The structure and properties of the membranes were characterized by Fourier transform infrared spectroscopy, X-ray diffraction, scanning electron microscopy and tensile testing. The effects of SPI content (W(SPI)) and the coagulants on the structure and properties of the membranes were investigated. The membranes exhibited porous structure. The pore size in the surfaces and cross-sections of the membranes increased with an increase of W(SPI) regardless of the coagulants. The membranes containing 10 wt% W(SPI) showed higher tensile strength and elongation at break than other membranes. The membranes with the same W(SPI) coagulated from acetic acid solution exhibited higher values of tensile strength, elongation at break and pore size in the surfaces and cross-sections than those corresponding membranes coagulated from sulphuric acid. The biocompatibility of the acetic acid-coagulated membranes was preliminarily evaluated by cell culture and in vivo implantation experiments. The results revealed that human umbilical vein endothelial cells (ECV304) grew well on this biomaterial. In comparison with the pure cellulose membrane, because of the incorporation of SPI and the resultant alteration of microstructure, the SPI-modified membranes showed an improved in vivo biocompatibility and biodegradability in the implantation experiments. These cellulose/SPI membranes warrant further explorations in biomedical fields.

  12. The effect of different anti-solvent and coconut shell content on properties of coconut shell regenerated cellulose biocomposite films

    NASA Astrophysics Data System (ADS)

    Hahary, Farah Norain; Husseinsyah, Salmah; Mostapha@Zakaria, Marliza

    2016-07-01

    In this study, coconut shell (CS) regenerated cellulose (RC) biocomposite films was prepared using dimethylacetamide/lithium chloride (DMAc/LiCl) solvent system. The effect of anti-solvents such as water and methanol for regeneration of cellulose and coconut shell content on properties of CS-RC biocomposite films was investigated. The used of water as anti-solvent for cellulose regeneration was found to have higher tensile properties compared to regenerated cellulose using methanol. Besides, the X-Ray diffraction (XRD) analysis also revealed that RC using water as anti-solvent have higher crystallinity index (CrI) than CS-RC biocomposite film using methanol. The tensile strength and modulus elasticity of CS-RC biocomposite films increased up to 3 wt% CS and decreased with further addition of CS. The elongation at break of CS-RC biocomposite films decreased with the increment of CS. The CrI of CS-RC bioocmposite films up to 3 wt% and decreased with at higher content of CS.

  13. [Study on spectroscopic characterization and property of PES/ micro-nano cellulose composite membrane material].

    PubMed

    Tang, Huan-Wei; Zhang, Li-Ping; Li, Shuai; Zhao, Guang-Jie; Qin, Zhu; Sun, Su-Qin

    2010-03-01

    In the present paper, the functional groups of PES/micro-nano cellulose composite membrane materials were characterized by Fourier transform infrared spectroscopy (FTIR). Also, changes in crystallinity in composite membrane materials were analyzed using X-ray diffraction (XRD). The effects of micro-nano cellulose content on hydrophilic property of composite membrane material were studied by measuring hydrophilic angle. The images of support layer structure of pure PES membrane material and composite membrane material were showed with scanning electron microscope (SEM). These results indicated that in the infrared spectrogram, the composite membrane material had characteristic peaks of both PES and micro-nano cellulose without appearance of other new characteristics peaks. It revealed that there were no new functional groups in the composite membrane material, and the level of molecular compatibility was achieved, which was based on the existence of inter-molecular hydrogen bond association between PES and micro-nano cellulose. Due to the existence of micro-nano cellulose, the crystallinity of composite membrane material was increased from 37.7% to 47.9%. The more the increase in micro-nano cellulose mass fraction, the better the van de Waal force and hydrogen bond force between composite membrane material and water were enhanced. The hydrophilic angle of composite membrane material was decreased from 55.8 degrees to 45.8 degrees and the surface energy was raised from 113.7 to 123.5 mN x m(-2). Consequently, the hydrophilic property of composite membrane material was improved. The number of pores in the support layer of composite membrane material was lager than that of pure PES membrane. Apparently, pores were more uniformly distributed.

  14. Ultrathin cellulose nanosheet membranes for superfast separation of oil-in-water nanoemulsions

    NASA Astrophysics Data System (ADS)

    Zhou, Ke; Zhang, Qiu Gen; Li, Hong Mei; Guo, Nan Nan; Zhu, Ai Mei; Liu, Qing Lin

    2014-08-01

    Oily wastewater is generated in diverse industrial processes, and its treatment has become crucial due to increasing environmental concerns. Herein, novel ultrathin nanoporous membranes of cellulose nanosheets have been fabricated for separation of oil-in-water nanoemulsions. The fabrication approach is facile and environmentally friendly, in which cellulose nanosheets are prepared by freeze-extraction of a very dilute cellulose solution. The as-prepared membranes have a cellulose nanosheet layer with a cut-off of 10-12 nm and a controllable thickness of 80-220 nm. They allow ultrafast water permeation and exhibit excellent size-selective separation properties. A 112 nm-thick membrane has a water flux of 1620 l m-2 h-1 bar-1 and a ferritin rejection of 92.5%. These membranes have been applied to remove oil from its aqueous nanoemulsions successfully, and they show an ultrafast and effective separation of oil-in-water nanoemulsions. The newly developed ultrathin cellulose membranes have a wide application in oily wastewater treatment, separation and purification of nanomaterials.Oily wastewater is generated in diverse industrial processes, and its treatment has become crucial due to increasing environmental concerns. Herein, novel ultrathin nanoporous membranes of cellulose nanosheets have been fabricated for separation of oil-in-water nanoemulsions. The fabrication approach is facile and environmentally friendly, in which cellulose nanosheets are prepared by freeze-extraction of a very dilute cellulose solution. The as-prepared membranes have a cellulose nanosheet layer with a cut-off of 10-12 nm and a controllable thickness of 80-220 nm. They allow ultrafast water permeation and exhibit excellent size-selective separation properties. A 112 nm-thick membrane has a water flux of 1620 l m-2 h-1 bar-1 and a ferritin rejection of 92.5%. These membranes have been applied to remove oil from its aqueous nanoemulsions successfully, and they show an ultrafast and effective

  15. Latex use as an occlusive membrane for guided bone regeneration.

    PubMed

    Ereno, Cibele; Guimarães, Sérgio A Catanzaro; Pasetto, Silvana; Herculano, Rondinelli Donizetti; Silva, Cecília Pereira; Graeff, Carlos F O; Tavano, Orivaldo; Baffa, Oswaldo; Kinoshita, Angela

    2010-12-01

    Latex extracted from Hevea brasiliensis was used as an occlusive membrane for guided bone regeneration. Twenty-four rabbits were divided in two groups: treated and control group. Critical size bone defects (2 cm × 1 cm) were surgically made in the rabbit calvarium. Two latex membranes were implanted in each animal of the treated group, whereas the control defect was filled only with autogenous blood clot. After 15, 30, 60, and 120 days, animals from each group were euthanized, and the samples with regenerated bone were removed. No signs of allergy or rejection were noticed around the calvarial bone defect of the treated group. In the histological analysis, no foreign body inflammatory reaction was observed in the adjacent tissues in contact with the membranes demonstrating that latex can be used at injured sites as an aid in the healing process. Histological analysis, digital radiography, and electron spin resonance were used to evaluate the progress of bone repair. The results show significant differences between groups (p < 0.05) suggesting that latex membranes accelerates healing in critical bone defects.

  16. Cellulose triacetate doped with ionic liquids for membrane gas separation

    NASA Astrophysics Data System (ADS)

    Lam, Benjamin Fatt Soon

    The doping of cellulose triacetate (CTA) with imidazolium based ionic liquids (ILs) is investigated in order to reduce the polymer crystallinity and enhance the affinity with CO2, thus increasing CO2 permeability and CO2/light gas selectivity. CTA membranes doped with [emim] BF4 or [emim] DCA were prepared, and the effect of the ILs loading on properties, such as crystallinity, density, degradation temperature, glass transition temperature, and gas transport properties, has been determined. In general, doping with IL reduces the crystallinity in CTA, increasing gas solubility, diffusivity and permeability. The ILs doping also increases CO 2/CH4 solubility selectivity and CO2/N2 permeability selectivity, due to the affinity of these ILs with CO2, instead of light gases such as CH4 and N2. This study provides a mechanistic understanding of interaction of ILs and CTA, and demonstrates an effective route in manipulating the morphology and gas transport properties of semi crystalline polymers by doping with ILs.

  17. Surface modification of cellulose acetate membrane using thermal annealing to enhance produced water treatment

    SciTech Connect

    Kusworo, T. D. Aryanti, N. Firdaus, M. M. H.; Sukmawati, H.

    2015-12-29

    This study is performed primarily to investigate the effect of surface modification of cellulose acetate using thermal annealing on the enhancement of membrane performance for produced water treatment. In this study, Cellulose Acetate membranes were casted using dry/wet phase inversion technique. The effect of additive and post-treatment using thermal annealing on the membrane surface were examined for produced water treatment. Therma annealing was subjected to membrane surface at 60 and 70 °C for 5, 10 and 15 second, respectively. Membrane characterizations were done using membrane flux and rejection with produced water as a feed, Scanning Electron Microscopy (SEM) and Fourier Transform Infra Red (FTIR) analysis. Experimental results showed that asymmetric cellulose acetate membrane can be made by dry/wet phase inversion technique. The results from the Scanning Electron Microscopy (FESEM) analysis was also confirmed that polyethylene glycol as additivie in dope solution and thermal annealing was affected the morphology and membrane performance for produced water treatment, respectively. Scanning electron microscopy micrographs showed that the selective layer and the substructure of membrane became denser and more compact after the thermal annealing processes. Therefore, membrane rejection was significantly increased while the flux was slighty decreased, respectively. The best membrane performance is obtained on the composition of 18 wt % cellulose acetate, poly ethylene glycol 5 wt% with thermal annealing at 70° C for 15 second.

  18. Surface modification of cellulose acetate membrane using thermal annealing to enhance produced water treatment

    NASA Astrophysics Data System (ADS)

    Kusworo, T. D.; Aryanti, N.; Firdaus, M. M. H.; Sukmawati, H.

    2015-12-01

    This study is performed primarily to investigate the effect of surface modification of cellulose acetate using thermal annealing on the enhancement of membrane performance for produced water treatment. In this study, Cellulose Acetate membranes were casted using dry/wet phase inversion technique. The effect of additive and post-treatment using thermal annealing on the membrane surface were examined for produced water treatment. Therma annealing was subjected to membrane surface at 60 and 70 °C for 5, 10 and 15 second, respectively. Membrane characterizations were done using membrane flux and rejection with produced water as a feed, Scanning Electron Microscopy (SEM) and Fourier Transform Infra Red (FTIR) analysis. Experimental results showed that asymmetric cellulose acetate membrane can be made by dry/wet phase inversion technique. The results from the Scanning Electron Microscopy (FESEM) analysis was also confirmed that polyethylene glycol as additivie in dope solution and thermal annealing was affected the morphology and membrane performance for produced water treatment, respectively. Scanning electron microscopy micrographs showed that the selective layer and the substructure of membrane became denser and more compact after the thermal annealing processes. Therefore, membrane rejection was significantly increased while the flux was slighty decreased, respectively. The best membrane performance is obtained on the composition of 18 wt % cellulose acetate, poly ethylene glycol 5 wt% with thermal annealing at 70° C for 15 second.

  19. The Arabidopsis COBRA protein facilitates cellulose crystallization at the plasma membrane.

    PubMed

    Sorek, Nadav; Sorek, Hagit; Kijac, Aleksandra; Szemenyei, Heidi J; Bauer, Stefan; Hématy, Kian; Wemmer, David E; Somerville, Chris R

    2014-12-12

    Mutations in the Arabidopsis COBRA gene lead to defects in cellulose synthesis but the function of COBRA is unknown. Here we present evidence that COBRA localizes to discrete particles in the plasma membrane and is sensitive to inhibitors of cellulose synthesis, suggesting that COBRA and the cellulose synthase complex reside in close proximity on the plasma membrane. Live-cell imaging of cellulose synthesis indicated that, once initiated, cellulose synthesis appeared to proceed normally in the cobra mutant. Using isothermal calorimetry, COBRA was found to bind individual β1-4-linked glucan chains with a KD of 3.2 μm. Competition assays suggests that COBRA binds individual β1-4-linked glucan chains with higher affinity than crystalline cellulose. Solid-state nuclear magnetic resonance studies of the cell wall of the cobra mutant also indicated that, in addition to decreases in cellulose amount, the properties of the cellulose fibrils and other cell wall polymers differed from wild type by being less crystalline and having an increased number of reducing ends. We interpret the available evidence as suggesting that COBRA facilitates cellulose crystallization from the emerging β1-4-glucan chains by acting as a "polysaccharide chaperone."

  20. Cellulose

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Cellulose properties and structure are reviewed, with a primary focus on crystal structure and polymorphy. This focus highlights the conversion from cellulose I to cellulose II, which converts the molecules to being all parallel to each other in the crystal to being antiparallel. This has been co...

  1. Biodegradable composite scaffolds of bioactive glass/chitosan/carboxymethyl cellulose for hemostatic and bone regeneration.

    PubMed

    Chen, Chen; Li, Hong; Pan, Jianfeng; Yan, Zuoqin; Yao, Zhenjun; Fan, Wenshuai; Guo, Changan

    2015-02-01

    Hemostasis in orthopedic osteotomy or bone cutting requires different methods and materials. The bleeding of bone marrow can be mostly stopped by bone wax. However, the wax cannot be absorbed, which leads to artificial prosthesis loosening, foreign matter reaction, and infection. Here, a bioactive glass/chitosan/carboxymethyl cellulose (BG/CS/CMC) composite scaffold was designed to replace traditional wax. WST-1 assay indicated the BG/CS/CMC composite resulted in excellent biocompatibility with no cytotoxicity. In vivo osteogenesis assessment revealed that the BG/CS/CMC composite played a dominant role in bone regeneration and hemostasis. The BG/CS/CMC composite had the same hemostasis effect as bone wax; in addition its biodegradation also led to the functional reconstruction of bone defects. Thus, BG/CS/CMC scaffolds can serve as a potential material for bone repair and hemostasis in critical-sized bone defects.

  2. X-ray Studies of Regenerated Cellulose Fibers Wet Spun from Cotton Linter Pulp in NaOH/Thiourea Aqueous Solutions

    SciTech Connect

    Chen,X.; Burger, C.; Fang, D.; Ruan, D.; Zhang, L.; Hsiao, B.; Chu, B.

    2006-01-01

    Regenerated cellulose fibers were fabricated by dissolution of cotton linter pulp in NaOH (9.5 wt%) and thiourea (4.5 wt%) aqueous solution followed by wet-spinning and multi-roller drawing. The multi-roller drawing process involved three stages: coagulation (I), coagulation (II) and post-treatment (III). The crystalline structure and morphology of regenerated cellulose fiber was investigated by synchrotron wide-angle X-ray diffraction (WAXD) and small-angle X-ray scattering (SAXS) techniques. Results indicated that only the cellulose II crystal structure was found in regenerated cellulose fibers, proving that the cellulose crystals were completely transformed from cellulose I to II structure during spinning from NaOH/thiourea aqueous solution. The crystallinity, orientation and crystal size at each stage were determined from the WAXD analysis. Drawing of cellulose fibers in the coagulation (II) bath (H{sub 2}SO{sub 4}/H{sub 2}O) was found to generate higher orientation and crystallinity than drawing in the post-treatment (III). Although the post-treatment process also increased crystal orientation, it led to a decrease in crystallinity with notable reduction in the anisotropic fraction. Compared with commercial rayon fibers fabricated by the viscose process, the regenerated cellulose fibers exhibited higher crystallinity but lower crystal orientation. SAXS results revealed a clear scattering maximum along the meridian direction in all regenerated cellulose fibers, indicating the formation of lamellar structure during spinning.

  3. The effect of acid hydrolysis pretreatment on crystallinity and solubility of kenaf cellulose membrane

    SciTech Connect

    Saidi, Anis Syuhada Mohd; Zakaria, Sarani; Chia, Chin Hua; Jaafar, Sharifah Nabihah Syed; Padzil, Farah Nadia Mohammad

    2015-09-25

    Cellulose was extracted from kenaf core pulp (KCP) by series of bleaching steps in the sequence (DEED) where D and E are referred as acid and alkali treatment. The bleached kenaf pulp (BKCP) is then pretreated with acid hydrolysis at room temperature for 1 and 3 h respectively. The pretreated cellulose is dissolved in lithium hydroxide/urea (LiOH/urea) and cellulose solution produced was immersed in distilled water bath. BKCP without treatment was also conducted for comparison purpose. The effects of acid hydrolysis pretreatment on solubility and crystallinity are investigated. Higher solubility of cellulose solution is achieved for treated samples. Cellulose II formation and crystallinity index of the cellulose membrane were determined by X-ray diffraction (XRD)

  4. The effect of acid hydrolysis pretreatment on crystallinity and solubility of kenaf cellulose membrane

    NASA Astrophysics Data System (ADS)

    Saidi, Anis Syuhada Mohd; Zakaria, Sarani; Chia, Chin Hua; Jaafar, Sharifah Nabihah Syed; Padzil, Farah Nadia Mohammad

    2015-09-01

    Cellulose was extracted from kenaf core pulp (KCP) by series of bleaching steps in the sequence (DEED) where D and E are referred as acid and alkali treatment. The bleached kenaf pulp (BKCP) is then pretreated with acid hydrolysis at room temperature for 1 and 3 h respectively. The pretreated cellulose is dissolved in lithium hydroxide/urea (LiOH/urea) and cellulose solution produced was immersed in distilled water bath. BKCP without treatment was also conducted for comparison purpose. The effects of acid hydrolysis pretreatment on solubility and crystallinity are investigated. Higher solubility of cellulose solution is achieved for treated samples. Cellulose II formation and crystallinity index of the cellulose membrane were determined by X-ray diffraction (XRD).

  5. Enzymatic membrane reactor for full saccharification of ionic liquid-pretreated microcrystalline cellulose.

    PubMed

    Lozano, Pedro; Bernal, Berenice; Jara, Antonio G; Belleville, Marie-Pierre

    2014-01-01

    Ultrafiltration reactors based on polymeric or ceramic membranes were shown to be suitable catalytic systems for fast enzymatic saccharification of cellulose, allowing the full recovery and reuse of enzymes. By pre-treating cellulose with the IL 1-butyl-3-methylimidazolium chloride, the suitability of this substrate for enzymatic saccharification in a reactor based on polymeric ultrafiltration membranes was demonstrated, leading to 95% cellulose hydrolysis in 4h at 50°C. The filtration process gave a clear glucose solution (up to 113 mM) at constant permeate flow (24.7 L h(-1) m(-2)), allowing the enzyme to be reused for 9 operation cycles under semi-continuous operation, without any loss of enzyme activity. Under continuous operation mode and using ceramic ultrafiltration membranes at different residence times, the enzymatic reactor showed constant profiles in both the permeate flow rate and the glucose concentration, demonstrating the excellent suitability of the proposed approach for the saccharification of cellulose.

  6. Polymeric Membrane Made of Cellulose Isolated from Tropical Water Hyacinth Blended with Chitosan

    NASA Astrophysics Data System (ADS)

    Istirokhatun, Titik; Rachmawaty, Richa; Meriyani, Metty; Rokhati, Nur; Susanto, Heru

    2017-02-01

    In Indonesia, membrane application is limited by the use of high cost imported membranes. Therefore, efforts to produce membrane using local materials are very important to be performed. Cellulose and chitosan are two materials, which their availability in Indonesia is abundant. In this work, cellulose acetate (CA) has been successfully produced from tropical water hyacinth via isolation and acetylation processes. By using FTIR, a comparative analysis of functional groups between the resulted CA and commercial CA was also investigated. The result shows that the IR spectra of the resulted CA and commercial CA are similar. The produced CA can further be processed into membrane. The resulting membranes were then characterized using SEM. In addition, the membranes were examined for filtering humic acid solution as surface water model. To improve the performance, CA membranes prepared from water hyacinth were modified by addition of chitosan (Chi) via blending in phase separation method. The resulting CA-Chi membranes were characterized using SEM and FTIR.

  7. Pretreatment by NaOH swelling and then HCl regeneration to enhance the acid hydrolysis of cellulose to glucose.

    PubMed

    Sun, Binzhe; Peng, Gege; Duan, Lian; Xu, Aihua; Li, Xiaoxia

    2015-11-01

    A simple pretreatment method, NaOH swelling at a low temperature and then HCl regeneration, was developed for depolymerization of cellulose to glucose. Cellulose was transformed into amorphous hydrogel during the treatment; and due to the easy diffusion of H(+) and Cl(-) ions into the cellulose hydrogel network as well as the strong ability of Cl(-) to disrupt the massive hydrogen bond, the hydrolysis rate was greatly enhanced. The method is effective for α-cellulose, microcrystalline cellulose, filter paper, ramie fiber and absorbent cotton. Even at a high α-cellulose concentration of 50g/L, 29.1% yield of glucose was still obtained within 10min at 160°C under microwave irradiation, where up to 16.2g/L of glucose solution was given. The influence of NaOH concentration, HCl concentration, hydrolysis temperature and time on the hydrolysis rate was investigated. The structure of cellulose hydrogel was also studied to confirm the reaction mechanism.

  8. Characterization and in vitro evaluation of bacterial cellulose membranes functionalized with osteogenic growth peptide for bone tissue engineering.

    PubMed

    Saska, Sybele; Scarel-Caminaga, Raquel Mantuaneli; Teixeira, Lucas Novaes; Franchi, Leonardo Pereira; Dos Santos, Raquel Alves; Gaspar, Ana Maria Minarelli; de Oliveira, Paulo Tambasco; Rosa, Adalberto Luiz; Takahashi, Catarina Satie; Messaddeq, Younès; Ribeiro, Sidney José Lima; Marchetto, Reinaldo

    2012-09-01

    The aim of this study was to characterize the physicochemical properties of bacterial cellulose (BC) membranes functionalized with osteogenic growth peptide (OGP) and its C-terminal pentapeptide OGP[10-14], and to evaluate in vitro osteoinductive potential in early osteogenesis, besides, to evaluate cytotoxic, genotoxic and/or mutagenic effects. Peptide incorporation into the BC membranes did not change the morphology of BC nanofibers and BC crystallinity pattern. The characterization was complemented by Raman scattering, swelling ratio and mechanical tests. In vitro assays demonstrated no cytotoxic, genotoxic or mutagenic effects for any of the studied BC membranes. Culture with osteogenic cells revealed no difference in cell morphology among all the membranes tested. Cell viability/proliferation, total protein content, alkaline phosphatase activity and mineralization assays indicated that BC-OGP membranes enabled the highest development of the osteoblastic phenotype in vitro. In conclusion, the negative results of cytotoxicity, genotoxicity and mutagenicity indicated that all the membranes can be employed for medical supplies, mainly in bone tissue engineering/regeneration, due to their osteoinductive properties.

  9. Antibacterial Nanostructured Polyhydroxybutyrate Membranes for Guided Bone Regeneration.

    PubMed

    Karahaliloğlu, Zeynep; Ercan, Batur; Taylor, Erik N; Chung, Stanley; Denkbaş, Emir B; Webster, Thomas J

    2015-12-01

    The principle of guided bone regeneration (GBR) in orthopedic, cranio-maxillofacial and dental tissue engineering applications is to create a secluded space for the treatment of large bone defects while excluding fibrous connective tissue formation at the defect area. In dental surgeries, a GBR membrane is placed near the dental implant in post-extraction sockets to grow new bone at the implant site, along with inhibiting infection due to the microbial nature of the mouth flora. Poly[(R)-3-hydroxybutyric acid] (PHB) is a natural polyester synthesized by a wide variety of microorganisms which has been proposed for various biomedical applications. In this study, to improve the performance of PHB as a GBR, a NaOH based alkaline treatment was designed to create nanofeatured PHB membranes. The newly fabricated nanofeatured PHB membranes were investigated for GBR applications. The results showed that a quick, simple, and inexpensive sodium hydroxide treatment modified the nanostructured surface morphology and chemistry of the PHB membranes by inducing hydrolysis of the ester bonds in the PHB backbone creating carboxylic surface functional groups, which increased the hydrophilicity of the PHB surfaces. Cytocompatibility studies showed increased proliferation of human osteoblasts (bone forming cells) on the NaOH treated PHB membranes compared to the untreated ones. Importantly, in vitro bacterial studies with Staphylococcus aureus (S. aureus) indicated that the NaOH-treated PHB surfaces inhibited S. aureus growth more than 60% after 48 hours of culture compared to the untreated PHB membrane. Thus, this study, for the first time, showed that nanofeatured PHB membranes modified with a NaOH treatment may be a useful anti-bacterial, osteoconductive GBR membrane for numerous orthopedic, cranio-maxillofacial and dental tissue engineering applications.

  10. Enzymatic hydrolysis of cellulose in a membrane bioreactor: assessment of operating conditions.

    PubMed

    Liu, Jianguo; Lu, Jianren; Cui, Zhanfeng

    2011-06-01

    The optimization of operating conditions for cellulose hydrolysis was systemically undertaken using an ultra-scaled down membrane bioreactor based on the parameter scanning ultrafiltration apparatus. The bioconversion of cellulose saccharification was carried out with freely suspended cellulase from Aspergillus niger as the biocatalyst. The polyethersulfone ultrafiltration membranes with a molecular weight cutoff of 10 kDa were used to construct the enzymatic membrane bioreactor, with the membrane showing a complete retaining of cellulase and cellobiase. The influence of solution pH, temperature, salt (NaCl) concentration, presence of cellobiase, cellulose-to-enzyme ratio and stirring speed on reducing sugar production was examined. The results showed that the addition of an appropriate amount of NaCl or cellobiase had a positive effect on reducing sugar formation. Under the identified optimal conditions, cellulose hydrolysis in the enzymatic membrane bioreactor was tested for a long period of time up to 75 h, and both enzymes and operation conditions demonstrated good stability. Also, the activation energy (E(a)) of the enzymatic hydrolysis, with a value of 34.11 ± 1.03 kJ mol(-1), was estimated in this study. The operational and physicochemical conditions identified can help guide the design and operation of enzymatic membrane bioreactors at the industrial scale for cellulose hydrolysis.

  11. Collagen-apatite nanocomposite membranes for guided bone regeneration.

    PubMed

    Song, Ju-Ha; Kim, Hyoun-Ee; Kim, Hae-Won

    2007-10-01

    Collagen-apatite nanocomposite is regarded as a potential biomaterial because of its composition and structure, which are similar to those of human hard tissues. However, there have been few investigations of its mechanical and biological benefits in direct comparison with a collagen equivalent. Herein, we successfully produced a biomedical membrane made of a nanocomposite, and systemically evaluated the mechanical, chemical, and biological properties of the nanocomposite in comparison with those of pure collagen. The results showed that significant improvements were achieved by the nanocomposite approach, particularly in terms of the mechanical strength and chemical stability. The present findings point to the potential usefulness of the collagen-apatite nanocomposite membrane in the field of guided bone regeneration (GBR).

  12. Celluloses filled ENR/PVC membranes for palm oil mill effluent (POME) treatment

    NASA Astrophysics Data System (ADS)

    Shamsuddin, Mohd Razali; Abdullah, Ibrahim; Othaman, Rizafizah

    2013-11-01

    Membranes from composite materials have been used especially in water treatment applications. In this paper the composite membranes of celluloses filled ENR/PVC were successfully prepared for POME treatment application. The preparation of the membrane involves solution blending, casting, phase inversion and drying methods. Two types of fillers, cellulose (Cell) and cellulose grafting polymethyl methacrylate (Cell-g-PMMA) were added into ENR/PVC matrix in various compositions (1, 5, 10, 15 and 20 wt%) to determine the effect of the filler to the performance of the membrane. The membranes were characterized by using FTIR and SEM. Membrane properties in terms of porosity and water flux were examined using mathematical calculation. FTIR spectrum shows the existence of stretching vibration from the functional group of ester carbonyl, -C=O at peak 1725 cm-1 that belongs to Cell-g-PMMA filler in ENR/PVC/Cell-g-PMMA membrane which makes the membranes slightly hydrophobic. SEM micrographs exhibit that pores were formed on both ENR/PVC/Cell and ENR/PVC/Cell-g-PMMA membranes. Water flux test indicates that ENR/PVC/Cell-20% was the highest because the addition of Cell increases the hydrophilicity of the membrane. In POME treatment, ENR/PVC/Cell-20% and ENR/PVC/Cell-g-PMMA-10% showed the highest decolorization.

  13. Synthesis and characterization of polyurethane-cellulose acetate blend membrane for chromium (VI) removal.

    PubMed

    Riaz, Tabinda; Ahmad, Adnan; Saleemi, Sidra; Adrees, Muhammad; Jamshed, Fahad; Hai, Abdul Moqeet; Jamil, Tahir

    2016-11-20

    Blended membranes of polyurethane and cellulose acetate were prepared, characterized and investigated for their performance. Various ratios of cellulose acetate were employed to prepare four different blend membranes. The characteristics of both pure and blend membranes were investigated and results were compared to distinguish their properties. Functional group analysis was carried out by attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR) of pure and blend samples. Contact angle measurement and water content were evaluated to determine the membrane hydrophilicity. Moreover, the membrane morphology was studied by scanning electron microscopy (SEM). The membrane permeation properties and ability to reject chromium (VI) ions were tested at various pH and pressure by utilizing different salt concentrations.

  14. Mechanism of DNA (Southern) and protein (Western) blotting on cellulose nitrate and other membranes.

    PubMed

    Van Oss, C J; Good, R J; Chaudhury, M K

    1987-03-27

    The transfer of DNA fractions from hydrophilic gels to nitrocellulose membranes (Southern blotting) which was soon followed by the description of an analogous procedure for RNA (Northern blotting), and somewhat later for proteins (Western blotting), has rapidly become an important separation and characterization method in molecular biology, genetic engineering, and immunological detection. Surface tension measurements have shown that the interfacial attraction between DNA and cellulose esters (-delta G132) in aqueous media can be considerable. The weaker binding energy of proteins to cellulose nitrate and to cellulose acetate may be compared to hydrophobic interaction chromatography, as on account of the somewhat lower [-delta G132] values, it often is necessary to "fix" them more tightly onto nitrocellulose by using high salt concentrations. The binding energy of RNA to both cellulose esters also is rather low. In addition to the effect of high ionic strength, the effect of adding methanol, and the effects of denaturation, heating and drying on the energy of attachment of the biopolymers to cellulose esters, have been studied. Cationized nylon membranes have been advocated recently, especially for electrophoretic transfer of nucleic acids (in which process high salt concentrations cannot easily be used). With positively charged nylon membranes, the attachment mainly occurs through the electrostatic attraction between the strongly negatively charged nucleic acids (or proteins) and the positively charged membrane. Also, more apolar membranes (of polyvinyl difluoride) have been proposed, which manifest a strong interfacial (hydrophobic) attraction to all the above biopolymers (regardless of their electrostatic charge). However, with these two novel membrane types it is no longer possible to exploit the large difference in binding energy between DNA and RNA, which makes cellulose nitrate membranes so uniquely suited for RNA-DNA hybridization assays.

  15. Immobilization of cholesterol oxidase on cellulose acetate membrane for free cholesterol biosensor development.

    PubMed

    Wang, Shenqi; Li, Shipu; Yu, Yaoting

    2004-01-01

    This article describes the immobilization of cholesterol oxidase on a cellulose acetate (CA) membrane activated by Sodium periodate, ethylenediamine, and glutaraldehyde etc. The properties of the immobilized enzyme membrane were investigated. The factors affecting the activity of immobilized enzyme such as the concentration of glutaraldehyde, the concentration of enzyme used during immobilization, temperature, pH, and immobilizing time etc. were also studied. The immobilized COD membrane has been used to construct fibre-optic fluorescent biosensor.

  16. Novel cellulose derivative, process for preparing the same and sulfur dioxide gas permselective membrane comprising the same

    SciTech Connect

    Imai, K.; Shiomi, T.; Tezuka, Y.

    1987-09-15

    This patent relates to a novel cellulose derivative and a sulfur dioxide gas permselective membrane comprising the same, and particularly to hydrocarbylsulfinylethyl cellulose, a process for preparing the same and the sulfur dioxide gas permselective membrane comprising the same. An object of the present invention is to provide hydrocarbylsulfinylethyl cellulose which is a novel cellulose derivative and useful as a material for the sulfur dioxide gas permselective membrane and a process for preparing the same. Another object of the present invention is to supply a novel sulfur dioxide gas permselective membrane having an excellent sulfur dioxide gas permselectivity. The present invention provides hydrocarbylsulfinylethyl cellulose. The novel hydrocarbylsulfinylethyl cellulose of the present invention indicates markedly high sulfur dioxide gas permselectivity compared with the conventional cellulose derivatives, for example, cellulose acetate, ethyl cellulose, etc. Accordingly, the sulfur dioxide gas permselective membrane of the present invention can be utilized for separation, purification of sulfur dioxide gas from a gas mixture such as air or for concentration of sulfur dioxide gas in a gas mixture, and is highly practical in industrial use. More specifically, the sulfur dioxide gas permselective membrane is useful for, for example, removal of harmful sulfur dioxide gas from discharged gases from the viewpoint of environmental protection and purification of starting gases for synthesis, etc. from the viewpoint of industrial production. Further, the hydrocarbylsulfinylethyl cellulose of the present invention is useful for a thickening agent, binder, protective colloidal agent, etc.

  17. Biocompatible Double-Membrane Hydrogels from Cationic Cellulose Nanocrystals and Anionic Alginate as Complexing Drugs Codelivery.

    PubMed

    Lin, Ning; Gèze, Annabelle; Wouessidjewe, Denis; Huang, Jin; Dufresne, Alain

    2016-03-23

    A biocompatible hydrogel with a double-membrane structure is developed from cationic cellulose nanocrystals (CNC) and anionic alginate. The architecture of the double-membrane hydrogel involves an external membrane composed of neat alginate, and an internal composite hydrogel consolidates by electrostatic interactions between cationic CNC and anionic alginate. The thickness of the outer layer can be regulated by the adsorption duration of neat alginate, and the shape of the inner layer can directly determine the morphology and dimensions of the double-membrane hydrogel (microsphere, capsule, and filmlike shapes). Two drugs are introduced into the different membranes of the hydrogel, which will ensure the complexing drugs codelivery and the varied drugs release behaviors from two membranes (rapid drug release of the outer hydrogel, and prolonged drug release of the inner hydrogel). The double-membrane hydrogel containing the chemically modified cellulose nanocrystals (CCNC) in the inner membrane hydrogel can provide the sustained drug release ascribed to the "nano-obstruction effect" and "nanolocking effect" induced by the presence of CCNC components in the hydrogels. Derived from natural polysaccharides (cellulose and alginate), the novel double-membrane structure hydrogel material developed in this study is biocompatible and can realize the complexing drugs release with the first quick release of one drug and the successively slow release of another drug, which is expected to achieve the synergistic release effects or potentially provide the solution to drug resistance in biomedical application.

  18. Studies on gas transport through dry cellulose acetate membranes prepared by solvent exchange technique

    SciTech Connect

    Lui, A.; Talbot, F.D.F.; Sourirajan, S.; Fouda, A.; Matsuura, T.

    1988-10-01

    The mechanism of gas transport through pores on the surface of dry cellulose acetate membranes under pressure was identified for membranes prepared by the solvent exchange technique using pure gas permeation rate data. The pure gases were helium, methane and carbon dioxide. The variables involved in the membrane preparation variables involved in the membrane preparation are the shrinkage temperature, the first solvent, the second solvent and the combinations thereof. Different conditions of membrane preparation produce different pore sizes. Depending on this pore size, one of the following mechanisms becomes dominant: Knudsen, surface and size exclusion.

  19. Removal of aqueous Hg(II) and Cr(VI) using phytic acid doped polyaniline/cellulose acetate composite membrane.

    PubMed

    Li, Renjie; Liu, Lifen; Yang, Fenglin

    2014-09-15

    Conductive composite membrane-phytic acid (PA) doped polyaniline (PANI)/cellulose acetate (CA) (PANI-PA/CA) was prepared in a simple and environmental-friendly method, in which aniline was blended with CA/PA solution and polymerized before the phase conversion. The resultant composite membranes were characterized by SEM, EDX, FTIR-ATR, BET and electrical resistance measurements. When used as adsorbent for Hg(II) and Cr(VI) ions, the prepared composite membrane exhibits excellent adsorption capability. The adsorption of Hg(II) and Cr(VI) follows a pseudo-second-order kinetic model and best fits the Langmuir isotherm model, with the maximum adsorption capacity reaching 280.11 and 94.34 mg g(-1), respectively. The heavy metal loaded composite membrane can be regenerated and reused after treatment with acid or alkali solution, making it a promising and practical adsorbent for Hg(II) and Cr(VI) removal. Tests with river water were also carried out, indicating good performance and application.

  20. Tailoring the properties of asymmetric cellulose acetate membranes by gas plasma etching.

    PubMed

    Olde Riekerink, M B; Engbers, G H M; Wessling, M; Feijen, J

    2002-01-15

    Cellulose triacetate (CTA) ultrafilters and cellulose acetate blend (CAB) desalination membranes were treated with a radiofrequency gas plasma (tetrafluoromethane (CF(4)) or carbon dioxide (CO(2)), 47-49 W, 0.04-0.08 mbar). Treatment times were varied between 15 s and 120 min. The plasma-treated top layer of the membranes was characterized by scanning electron microscopy, X-ray photoelectron spectroscopy, and contact angle measurements to obtain information about surface structure, chemistry, and wettability, respectively. The membrane properties (e.g., permeability, selectivity, fouling) were studied by waterflux measurements, molecular weight cutoff measurements, and fouling experiments with bovine serum albumin. CO(2) plasma treatment resulted in gradual etching of the membrane's dense top layer. Permeation and selectivity changed significantly for treatment times of 0-15 min for CTA and 5-60 min for CAB membranes. Moreover, CTA membranes were hydrophilized during CO(2) plasma treatment whereas CF(4) plasma treatment led to hydrophobic surfaces due to strong fluorination of the top layer. This study shows that gas plasma etching can tailor the properties of asymmetric cellulose acetate membranes by simultaneously modifying the chemistry and structure of the top layer. The low fouling properties of CTA membranes were thereby largely maintained.

  1. Investigation of the pore structure and morphology of cellulose acetate membranes using small-angle neutron scattering. 1: Cellulose acetate active layer membranes

    SciTech Connect

    Kulkarni, S.; Krause, S. ); Wignall, G.D. . Solid State Div.); Hammouda, B. . Center for High Resolution Neutron Scattering)

    1994-11-07

    The structure of ultrathin cellulose acetate membranes, known as active layer membranes, has been investigated using small-angle neutron scattering. These membranes are known to have structural and functional similarity to the surface or skin layer in commercial reverse-osmosis (RO) membranes and hence are useful model systems for understanding the structure of the RO membrane skin layer. Active layer membranes were studied after swelling them with either D[sub 2]O or CD[sub 3]OD. The results in both cases clearly indicated the presence of very small (10--20 [angstrom]) porous structures in the membrane. The presence of such pores has been a subject of long-standing controversy in this area. The data were analyzed using a modified Debye-Bueche analysis and the resultant membrane structure was seen to agree well with structural information from electron microscopic studies. Finally, a possible explanation for the differences in scattering observed between the D[sub 2]O swollen membranes and the CD[sub 3]OD swollen membranes has been presented.

  2. Combined effects of raw materials and solvent systems on the preparation and properties of regenerated cellulose fibers.

    PubMed

    Chen, Jinghuan; Guan, Ying; Wang, Kun; Zhang, Xueming; Xu, Feng; Sun, Runcang

    2015-09-05

    To investigate the combined effects of materials and solvents on the preparation, structural and mechanical properties of regenerated cellulose fibers, four cellulosic materials (microcrystalline cellulose, cotton linter pulp, bamboo pulp and bleached softwood sulfite dissolving pulp) and six non-derivative solvents (NaOH/urea aqueous solution, N,N-dimethylacetamide/lithium chloride, N-methyl-morpholine-N-oxide, 1-butyl-3-methylimidazolium chloride, 1-allyl-3-methylimidazolium chloride and 1-ethyl-3-methylimidazolium acetate) were used to prepare fibers with wet spinning method. The results showed that the dissolvability of solvent was the determining factor in cellulose dissolution, and the dissolving time was influenced by the raw materials' properties, such as molecular weight, exposed area and hemicellulose content. The crystallinity and elongation at break of the fibers were almost fixed and not affected by the materials and solvents. However, the tensile strength of the fibers was directly proportional to the molecular weight of the raw materials, and varied with the type of solvents through cellulose degradation.

  3. Absorbent properties of carboxymethylated fiber, hydroentangled nonwoven and regenerated cellulose: a comparative study

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Commercially-available, bleached cotton fibers, rayon, and their hydroentangled counterparts were carboxymethylated to produce cellulosic products with increased absorbency. These cellulose materials were tested for absorbance, spectroscopic properties, degree of substitution and carding ability. Ca...

  4. Bacterial cellulose nanofibrillar patch as a wound healing platform of tympanic membrane perforation.

    PubMed

    Kim, Jangho; Kim, Seung Won; Park, Subeom; Lim, Ki Taek; Seonwoo, Hoon; Kim, Yeonju; Hong, Byung Hee; Choung, Yun-Hoon; Chung, Jong Hoon

    2013-11-01

    Bacterial cellulose (BC)-based biomaterials on medical device platforms have gained significant interest for tissue-engineered scaffolds or engraftment materials in regenerative medicine. In particular, BC has an ultrafine and highly pure nanofibril network structure and can be used as an efficient wound-healing platform since cell migration into a wound site is strongly meditated by the structural properties of the extracellular matrix. Here, the fabrication of a nanofibrillar patch by using BC and its application as a new wound-healing platform for traumatic tympanic membrane (TM) perforation is reported. TM perforation is a very common clinical problem worldwide and presents as conductive hearing loss and chronic perforations. The BC nanofibrillar patch can be synthesized from Gluconacetobacter xylinus; it is found that the patch contained a network of nanofibrils and is transparent. The thickness of the BC nanofibrillar patch is found to be approximately 10.33 ± 0.58 μm, and the tensile strength and Young's modulus of the BC nanofibrillar patch are 11.85 ± 2.43 and 11.90 ± 0.48 MPa, respectively, satisfying the requirements of an ideal wound-healing platform for TM regeneration. In vitro studies involving TM cells show that TM cell proliferation and migration are stimulated under the guidance of the BC nanofibrillar patch. In vivo animal studies demonstrate that the BC nanofibrillar patch promotes the rate of TM healing as well as aids in the recovery of TM function. These data demonstrate that the BC nanofibrillar patch is a useful wound-healing platform for TM perforation.

  5. Bacterial cellulose membrane produced by Acetobacter sp. A10 for burn wound dressing applications.

    PubMed

    Kwak, Moon Hwa; Kim, Ji Eun; Go, Jun; Koh, Eun Kyoung; Song, Sung Hwa; Son, Hong Joo; Kim, Hye Sung; Yun, Young Hyun; Jung, Young Jin; Hwang, Dae Youn

    2015-05-20

    Bacteria cellulose membranes (BCM) are used for wound dressings, bone grafts, tissue engineering, artificial vessels, and dental implants because of their high tensile strength, crystallinity and water holding ability. In this study, the effects of BCM application for 15 days on healing of burn wounds were investigated based on evaluation of skin regeneration and angiogenesis in burn injury skin of Sprague-Dawley (SD) rats. BCM showed a randomly organized fibrils network, 12.13 MPa tensile strength, 12.53% strain, 17.63% crystallinity, 90.2% gel fraction and 112.14 g × m(2)/h highest water vapor transmission rate (WVTR) although their swelling ratio was enhanced to 350% within 24h. In SD rats with burned skin, the skin severity score was lower in the BCM treated group than the gauze (GZ) group at all time points, while the epidermis and dermis thickness and number of blood vessels was greater in the BCM treated group. Furthermore, a significant decrease in the number of infiltrated mast cells and in vascular endothelial growth factor (VEGF) and angiopoietin-1 (Ang-1) expression was observed in the BCM treated group at day 10 and 15. Moreover, a significant high level in collagen expression was observed in the BCM treated group at day 5 compared with GZ treated group, while low level was detected in the same group at day 10 and 15. However, the level of metabolic enzymes representing liver and kidney toxicity in the serum of BCM treated rats was maintained at levels consistent with GZ treated rats. Overall, BCM may accelerate the process of wound healing in burn injury skin of SD rats through regulation of angiogenesis and connective tissue formation as well as not induce any specific toxicity against the liver and kidney.

  6. Surface chemistry of electrospun cellulose nitrate nanofiber membranes.

    PubMed

    Nartker, Steven; Askeland, Per; Wiederoder, Sara; Drzal, Lawrence T

    2011-02-01

    Electrospinning is a rapidly developing technology that provides a unique way to produce novel polymer nanofibers with controllable diameters. Cellulose nitrate non-woven mats of submicron-sized fibers with diameters of 100-1200 nm were prepared. The effects of processing equipment collector design void gap, and steel drum coated with polyvinylidene dichloride (PVDC) were investigated. The PVDC layer applied to the rotating drum aided in fiber harvesting. Electron microscopy (FESEM and ESEM) studies of as-spun fibers revealed that the morphology of cellulose nitrate fibers depended on the collector type and solution viscosity. When a rotating steel drum was employed a random morphology was observed, while the void gap collector produced aligned fiber mats. Increases in viscosity lead to larger diameter fibers. The fibers collected were free from all residual solvents and could undergo oxygen plasma treatment to increase the hydropholicity.

  7. Membrane-based recovery of glucose from enzymatic hydrolysis of ionic liquid pretreated cellulose.

    PubMed

    Abels, Christian; Thimm, Kristof; Wulfhorst, Helene; Spiess, Antje Christine; Wessling, Matthias

    2013-12-01

    In this work, a membrane-based downstream process for the recovery of glucose from cellulose hydrolysis is described and evaluated. The cellulose is pretreated with the ionic liquid 1,3-dimethyl-imidazolium dimethylphosphate to reduce its crystallinity. After enzymatic conversion of cellulose to glucose the hydrolysate is filtered with an ultrafiltration membrane to remove residual particulates and enzymes. Nanofiltration is applied to purify the glucose from molecular intermediates, such as cellobiose originating from the hydrolysis reaction. Finally, the ionic liquid is removed from the hydrolysate via electrodialysis. Technically, these process steps are feasible. An economic analysis of the process reveals that the selling price of glucose from this production process is about 2.75 €/kg which is too high as compared to the current market price.

  8. Fabrication of drug-loaded anti-infective guided tissue regeneration membrane with adjustable biodegradation property.

    PubMed

    Xue, Jiajia; Shi, Rui; Niu, Yuzhao; Gong, Min; Coates, Phil; Crawford, Aileen; Chen, Dafu; Tian, Wei; Zhang, Liqun

    2015-11-01

    For guided tissue regeneration (GTR) membrane, synchronization of the membrane biodegradation rate and tissue regeneration rate is important. Besides, the major reason for GTR membrane failure in clinical application is infection which can be prevented by loading anti-bacterial drug. To realize the consistency in membrane degradation rate and tissue regeneration rate of the anti-infective membrane, we developed metronidazole-loaded electrospun poly(ɛ-caprolactone)-gelatin nanofiber membranes with different poly(ɛ-caprolactone)/gelatin ratios (95:5, 90:10, 80:20, 70:30, 60:40, and 50:50). Homogeneous nanofibers were successfully fabricated. The mechanical strength of the membranes increased with the poly(ɛ-caprolactone) content, while the hydrophilicity decreased. The controlled and sustained release of metronidazole from all the membranes prevented the colonization of anaerobic bacteria. At all poly(ɛ-caprolactone)/gelatin ratios, all the membranes presented good biocompatibility while the increase of gelatin content resulted in enhanced cell adhesion and proliferation. Subcutaneous implantation in rabbits for 8 months demonstrated that all the membranes showed good biocompatibility without infection. Both in vitro and in vivo results showed that the biodegradation rate of the membranes was accelerated with the increase of gelatin content. The biodegradation rate and biocompatibility of the membranes can be adjusted by changing the PCL/gelatin ratio. The optimal membrane can be chosen based on the patient and tissue type to realize the synchronization of membrane degradation with tissue regeneration for the best treatment effect.

  9. Efficiency and biocompatibility of a polyethylene glycol grafted cellulosic membrane during hemodialysis.

    PubMed

    Akizawa, T; Kino, K; Koshikawa, S; Ikada, Y; Kishida, A; Yamashita, M; Imamura, K

    1989-01-01

    Dialytic efficiency and biocompatibility of a new modified cellulose membrane (NMC) were examined in vitro and clinically. NMC was obtained by grafting polyethylene-glycol (PEG) chains to the membrane surface of ordinary cellulose (OC), and it was expected that the random movement of PEG chains would prevent blood cells and large plasma proteins from coming into contact with the membrane surface, resulting in improving the biocompatibility and thrombogenicity of the membrane. Surface characteristics of NMC were rendered anionic and hydrophilic, however, the activations of complement and platelet systems were clearly suppressed in NMC. Minimum heparin requirement for hemodialysis was significantly lower with NMC than with OC dialyzer. No significant difference in solute and water removal was observed between the two dialyzers. These results indicate that NMC can provide increased biocompatibility and antithrombogenic effect while retaining the essential dialysis efficiency of OC.

  10. Controlled release and antibacterial activity of tetracycline hydrochloride-loaded bacterial cellulose composite membranes.

    PubMed

    Shao, Wei; Liu, Hui; Wang, Shuxia; Wu, Jimin; Huang, Min; Min, Huihua; Liu, Xiufeng

    2016-07-10

    Bacterial cellulose (BC) is widely used in biomedical applications. In this study, we prepared an antibiotic drug tetracycline hydrochloride (TCH)-loaded bacterial cellulose (BC) composite membranes, and evaluated the drug release, antibacterial activity and biocompatibility. The structure and morphology of the fabricated BC-TCH composite membranes were characterized using scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR). The TCH release results show that the incorporation of BC matrix to load TCH is able to control the release. In vitro antibacterial assay demonstrate that the developed BC-TCH composites displayed excellent antibacterial activity solely associated with the loaded TCH drug. More importantly, the BC-TCH composite membranes display good biocompatibility. These characteristics of BC-TCH composite membranes indicate that they may successfully serve as wound dressings and other medical biomaterials.

  11. Performance of cellulose acetate butyrate membranes in hyperfiltration of sodium chloride and urea feed solution

    NASA Technical Reports Server (NTRS)

    Wydeven, T.; Leban, M.

    1973-01-01

    Cellulose acetate butyrate (CAB) membranes are shown to give high salt and urea rejection with water flux of about 3 gallons/sq ft per day at 600 psig. Membranes prepared from a formulation containing glyoxal show a significant increase in flux and decrease in salt and urea rejection with drying time. Zero drying time gives maximum urea and salt rejection and is therefore most suitable for hyperfiltration of sodium chloride and urea feed solution.

  12. CHARACTERISTICS OF POROUS CELLULOSE ACETATE MEMBRANES FOR THE SEPARATION OF SOME INORGANIC SALTS IN AQUEOUS SOLUTION,

    DTIC Science & Technology

    Experimental results are presented to illustrate the effect of operating variables on the separation and flow characteristics of porous cellulose ... acetate membranes. The results are discussed from the point of view of the preferential sorption and capillary flow mechanism, together with the concept

  13. A simple cellulose acetate membrane-based small lanes technique for protein electrophoresis.

    PubMed

    Na, Na; Liu, Tingting; Yang, Xiaojun; Sun, Binjie; Ouyang, Jenny; Ouyang, Jin

    2012-08-01

    Combining electrophoresis with a cellulose acetate membrane-based technique, we developed a simple and low-cost method, named cellulose acetate membrane-based small lanes (CASL), for protein electrophoresis. A home-made capillary plotter controlled by a 3D moving stage was used to create milli-to-micro channels by printing poly(dimethylsiloxane) on to a hydrophilic cellulose acetate membrane. In the hydrophilic channels, 5 nL protein mixture was separated on the basis of electro-migration under an electric field. Compared with polyacrylamide gel electrophoresis (PAGE), CASL resulted in higher protein signal intensity for separation of mixtures containing the same mass of protein. The platform was easily fabricated at low cost (approx. $0.005 for each 1-mm-wide channel), and separation of three protein mixtures was completed in 15 min. Both electrophoresis time and potential affected the separation. Rather than chromatographic separation, this method accomplished application of microchannel techniques for cellulose acetate membrane-based protein electrophoresis. It has potential in proteomic analysis, especially for rapid, low-cost, and low-volume sample analysis in clinical diagnosis.

  14. Hyaluronic acid and oxidized regenerated cellulose prevent adhesion reformation after adhesiolysis in rat models

    PubMed Central

    Zhang, Yan; Liu, Qin; Yang, Ning; Zhang, Xuegang

    2016-01-01

    Postsurgical adhesion formation is the most common complication in abdominal and pelvic surgery. Adhesiolysis is the most commonly applied treatment for adhesion formation but is often followed by adhesion reformation. Therefore, an efficient strategy should be adopted to solve these problems. This study aimed to explore whether hyaluronic acid and oxidized regenerated cellulose (ORC) could prevent adhesion formation and reformation. Thirty female Sprague Dawley rats were randomly divided into three groups (n=10 each) and subjected to different treatments during the first and second surgery. The control group was treated with isotonic sodium chloride, the ORC group was treated with ORC (1.5×1 cm), and the medical sodium hyaluronate (MSH) group was treated with 1% MSH (0.5 mL). At 2 weeks after the first surgery, adhesion scores in the MSH group (1.90±0.99) and the ORC group (1.40±0.97) were significantly lower than those in the control group (3.00±0.82) (P=0.005). Similarly, 2 weeks after the second surgery, adhesion scores in the MSH group (2.00±0.82) and the ORC group (1.50±1.27) were significantly lower than those in the control group (3.50±0.53) (P=0.001). In addition, body weights in the MSH group and the ORC group did not change significantly, whereas the control group showed a consistent decrease in body weight during the experiment. Histological examination revealed that inflammatory infiltration was involved in both adhesion formation and reformation. In conclusion, hyaluronic acid and ORC were both efficient in reducing adhesion formation and reformation in the rat model. PMID:27822014

  15. Hyaluronic acid and oxidized regenerated cellulose prevent adhesion reformation after adhesiolysis in rat models.

    PubMed

    Zhang, Yan; Liu, Qin; Yang, Ning; Zhang, Xuegang

    2016-01-01

    Postsurgical adhesion formation is the most common complication in abdominal and pelvic surgery. Adhesiolysis is the most commonly applied treatment for adhesion formation but is often followed by adhesion reformation. Therefore, an efficient strategy should be adopted to solve these problems. This study aimed to explore whether hyaluronic acid and oxidized regenerated cellulose (ORC) could prevent adhesion formation and reformation. Thirty female Sprague Dawley rats were randomly divided into three groups (n=10 each) and subjected to different treatments during the first and second surgery. The control group was treated with isotonic sodium chloride, the ORC group was treated with ORC (1.5×1 cm), and the medical sodium hyaluronate (MSH) group was treated with 1% MSH (0.5 mL). At 2 weeks after the first surgery, adhesion scores in the MSH group (1.90±0.99) and the ORC group (1.40±0.97) were significantly lower than those in the control group (3.00±0.82) (P=0.005). Similarly, 2 weeks after the second surgery, adhesion scores in the MSH group (2.00±0.82) and the ORC group (1.50±1.27) were significantly lower than those in the control group (3.50±0.53) (P=0.001). In addition, body weights in the MSH group and the ORC group did not change significantly, whereas the control group showed a consistent decrease in body weight during the experiment. Histological examination revealed that inflammatory infiltration was involved in both adhesion formation and reformation. In conclusion, hyaluronic acid and ORC were both efficient in reducing adhesion formation and reformation in the rat model.

  16. Novel carboxymethyl cellulose based nanocomposite membrane: Synthesis, characterization and application in water treatment.

    PubMed

    Saber-Samandari, Samaneh; Saber-Samandari, Saeed; Heydaripour, Samira; Abdouss, Majid

    2016-01-15

    Significant efforts have been made to develop composite membranes with high adsorption efficiencies for water treatment. In this study, a carboxymethyl cellulose-graft-poly(acrylic acid) membrane was synthesized in the presence of silica gel, which was used as an inorganic support. Then, different amounts of bentonite were introduced to the carboxymethyl cellulose (CMC) grafted networks as a multifunctional crosslinker, and nanocomposite membranes were prepared. The nanocomposite membranes were characterized using Fourier transform infrared spectroscopy, and scanning electron microscopy, which revealed their compositions and surface morphologies. The novel synthesized nanocomposite membranes were utilized as adsorbents for the removal of crystal violet (CV) and cadmium (Cd (II)) ions, which were selected as representatives of a dye and a heavy metal, respectively. We explored the effects of various parameters, such as time, pH, temperature, initial concentration of adsorbate solution and amount of adsorbent, on membrane adsorption capacity. Furthermore, the kinetic, adsorption isotherm models and thermodynamic were employed for the description of adsorption processes. The maximum adsorption capacities of membranes for CV and Cd (II) ions were found to be 546 and 781 mg g(-1), respectively. The adsorption of adsorbate ions by all types of nanocomposite membranes followed pseudo-second-order kinetic model and was best fit with the Freundlich adsorption isotherm. The results indicated that the synthesized nanocomposite membrane is an efficient adsorbent for the removal of cationic dye and metal contaminants from aqueous solution during water treatment.

  17. Adhesion of a Mycobacterium sp. to cellulose diacetate membranes used in reverse osmosis.

    PubMed Central

    Ridgway, H F; Rigby, M G; Argo, D G

    1984-01-01

    The kinetics of adhesion of a Mycobacterium sp. to cellulose diacetate reverse-osmosis membranes is described. This Mycobacterium sp. (strain BT2-4) was previously implicated in the initial stages of reverse-osmosis membrane biofouling at a wastewater reclamation facility. Adhesion of BT2-4 cells to the cellulose diacetate membrane surfaces occurred within 1 to 2 h at 30 degrees C and exhibited saturation-type kinetics which conformed closely to the Langmuir adsorption isotherm (Pearson r correlation coefficient = 0.977), a mathematical expression describing the partitioning of substances between a solution and solid-liquid interface. This suggests that the cellulose diacetate membrane surfaces may possess a finite number of available binding sites to which the mycobacteria can adhere. Treatment of the attached mycobacteria with different enzymes suggested that cell surface polypeptides, alpha-1, 4- or alpha-1,6-linked glucan polymers, and carboxyl ester bond-containing substances (possibly peptidoglycolipids) may be involved in mycobacterial adhesion. The possible implication of these findings for reverse-osmosis membrane biofouling are discussed. Images PMID:6696424

  18. Evaluation of a novel vitamin E coated cellulosic membrane hollow fiber dialyzer.

    PubMed

    MacGinley, R; Westhuyzen, J; Saltissi, D; Morgan, C; Healy, H; Thirlwell, G K; Disney, A P

    2001-01-01

    Adverse physiologic effects accompany hemodialysis. Biocompatible dialyzer membranes may both limit oxidative stress and decrease beta2-microglobulin production, thereby reducing patient morbidity. We compared standard solute clearance, lipid, and antioxidant effects of a novel cellulosic membrane dialyzer modified with covalently bonded vitamin E (Excebrane Clirans E15, Terumo Australia) with standard cellulosic and polysulphone membrane dialyzers. Stable adult hemodialysis patients taking no lipid lowering or antioxidant therapy (n = 17; 9 male, 8 female) were recruited into a 10 week, prospective, unblinded study. Measurements were made at baseline on their usual dialyzer and after 2, 4, and 10 weeks of Excebrane use. Excebrane demonstrated good in vivo clearance of standard solutes relative to surface area. Predialysis beta2-microglobulin levels were unchanged with time and were significantly lower postdialysis than with cellulose acetate (p < 0.05). Oxidized low density lipoprotein levels as measured by nitrotyrosine residues were high predialysis, but tended to decrease with both membranes (p > 0.05). Total antioxidant status fell during dialysis (p < 0.0005), but plasma vitamin A and E concentrations increased (p = 0.007 and p = 0.02, respectively). Baseline vitamin A levels were high in all patients and, along with vitamin E, total antioxidant status and lipid profiles did not change over time with Excebrane use. Excebrane is an efficient, biocompatible membrane with no deleterious effects on beta2-microglobulin or lipids. More long-term study is merited.

  19. Clinical effects of a polyethylene glycol grafted cellulose membrane on thrombogenicity and biocompatibility during hemodialysis.

    PubMed

    Akizawa, T; Kino, K; Kinugasa, E; Koshikawa, S; Ikada, Y; Kishida, A; Hatanaka, Y; Imamura, K

    1990-01-01

    The biocompatibility and thrombogenicity of polyethylene-glycol (PEG)-grafted cellulose hemodialysis (HD) membranes (PEGC) were investigated in cross-over HD of five HD patients with ordinary cellulose (OC). The PEGC significantly suppressed transient leukocyte and thrombocytopenia, and release of C3a, beta-thromboglobulin and platelet factor 4, in corresponding with the quantity of grafted PEG. HD with PEGC resulted in lower granulocyte elastase production, protein and blood cells adsorption on the membrane surface than those with OC. Minimum heparin in HD with PEGC was three times lower than that with OC, with the thrombin-antithrombin III complex elevation lower than that in HD with OC. The results indicate that the grafted PEG effectively suppresses blood and membrane interaction, thus improving biocompatibility and reducing thrombogenicity in clinical HD.

  20. Self-sterilized composite membranes of cellulose acetate/polyethylene glycol for water desalination.

    PubMed

    Ahmad, Adnan; Jamshed, Fahad; Riaz, Tabinda; Gul, Sabad-E-; Waheed, Sidra; Sabir, Aneela; AlAnezi, Adnan Alhathal; Adrees, Muhammad; Jamil, Tahir

    2016-09-20

    Cellulose acetate/Polyethylene glycol-600 composite membranes were fabricated by two step phase inversion procedure and modified by in-situ reduction of silver nitrate. FTIR spectra demonstrated the existence of functional groups for bonding of silver with oxygen at 370cm(-1), 535cm(-1). The XRD diffractogram indicates characteristic peaks at 2θ values of 38.10°, 44.30°, 64.40°, and 77.30° which confirm the successful incorporation of silver within matrix of composite membranes. The morphology of composite membranes with appearances of spongy voids was exemplified from the scanning electron microscope. The atomic force microscopy was used to determine the increase in the surface roughness of the membranes. The increase in hydrophilicity, measured through contact angle, is rendered to the embedment of silver. The modification of membranes increased the flux from 0.80 to 0.95L/hr.m(2). The resulting membranes have outstanding ability to fight against gram negative Escherichia Coli and Bacillus Sabtilus. The novel cellulose acetate/polyethylene glycol membranes customized with silver have paved the path for evolution of axenic membranes.

  1. Cellulose/soy protein composite-based nerve guidance conduits with designed microstructure for peripheral nerve regeneration

    NASA Astrophysics Data System (ADS)

    Gan, Li; Zhao, Lei; Zhao, Yanteng; Li, Ke; Tong, Zan; Yi, Li; Wang, Xiong; Li, Yinping; Tian, Weiqun; He, Xiaohua; Zhao, Min; Li, Yan; Chen, Yun

    2016-10-01

    Objective. The objective of this work was to develop nerve guidance conduits from natural polymers, cellulose and soy protein isolate (SPI), by evaluating the effects of cellulose/SPI film-based conduit (CSFC) and cellulose/SPI sponge-based conduit (CSSC) on regeneration of nerve defects in rats. Approach. CSFC and CSSC with the same chemical components were fabricated from cellulose and SPI. Effects of CSSC and CSFC on regeneration of the defective nerve were comparatively investigated in rats with a 10 mm long gap in sciatic nerve. The outcomes of peripheral nerve repair were evaluated by a combination of electrophysiological assessment, Fluoro-Gold retrograde tracing, double NF200/S100 immunofluorescence analysis, toluidine blue staining, and electron microscopy. The probable molecular mechanism was investigated using quantitative real-time PCR (qPCR) analysis. Main results. Compared with CSFC, CSSC had 2.69 times higher porosity and 5.07 times higher water absorption, thus ensuring much higher permeability. The nerve defects were successfully bridged and repaired by CSSC and CSFC. Three months after surgery, the CSSC group had a higher compound muscle action potential amplitude ratio, a higher percentage of positive NF200 and S100 staining, and a higher axon diameter and myelin sheath thickness than the CSFC group, showing the repair efficiency of CSSC was higher than that of CSFC. qPCR analysis indicated the mRNA levels of nerve growth factor, IL-10, IL-6, and growth-associated protein 43 (GAP-43) were higher in the CSSC group. This also indicated that there was better nerve repair with CSSC due to the higher porosity and permeability of CSSC providing a more favourable microenvironment for nerve regeneration than CSFC. Significance. A promising nerve guidance conduit was developed from cellulose/SPI sponge that showed potential for application in the repair of nerve defect. This work also suggests that nerve guidance conduits with better repair efficiency

  2. Enhanced guided bone regeneration by asymmetrically porous PCL/pluronic F127 membrane and ultrasound stimulation.

    PubMed

    Oh, Se Heang; Kim, Tae Ho; Chun, So Young; Park, Eui Kyun; Lee, Jin Ho

    2012-01-01

    Recently, we developed a novel method for fabricating a guided bone regeneration (GBR) membrane with an asymmetrical pore structure and hydrophilicity by an immersion precipitation method. Results from an animal study, in a cranial defect model in rats, indicated that the unique asymmetrically porous GBR membrane would provide a good environment for bone regeneration. In the present study, we applied low intensity pulsed ultrasound as a simple and non-invasive stimulus to an asymmetrically porous polycaprolactone (PCL)/Pluronic F127 GBR membrane-implanted site transcutaneously in rats to investigate the feasibility of using ultrasound to stimulate enhanced bone regeneration through the membrane. It was observed that the ultrasound-stimulated PCL/F127 GBR membrane group had much faster bone regeneration behavior than a PCL/F127 membrane group w/o ultrasound or a control group (w/o membrane and ultrasound). The greater bone regeneration behavior in the GBR membrane/ultrasound group may be caused by a synergistic effect of the asymmetrically porous PCL/F127 membrane with unique properties (selective permeability, hydrophilicity and osteoconductivity), and the stimulatory effect of ultrasound (induction of angiogenesis and osteogenesis of cells).

  3. Asymmetric Collagen/chitosan Membrane Containing Minocycline-loaded Chitosan Nanoparticles for Guided Bone Regeneration

    PubMed Central

    Ma, Shiqing; Adayi, Aidina; Liu, Zihao; Li, Meng; Wu, Mingyao; Xiao, Linghao; Sun, Yingchun; Cai, Qing; Yang, Xiaoping; Zhang, Xu; Gao, Ping

    2016-01-01

    Infections caused by pathogens colonization at wound sites in the process of bone healing are considered as one of the major reasons for the failure of guided bone regeneration (GBR). The objective of this study was to prepare a novel asymmetric collagen/chitosan GBR membrane containing minocycline-loaded chitosan nanoparticles. The morphologies of the membranes and nanoparticles were observed by SEM and TEM, respectively. The characterization and biocompatibility of the membranes was evaluated. The effect of the membrane on bone regeneration was assessed using the critical-size at cranial defect model. TEM images showed the spherical morphology of the nanoparticles. The results of SEM indicated that the asymmetric membrane contained a dense collagen layer and a loose chitosan layer. An in vitro experiment showed that the membrane can inhibit bacterial growth and promote osteoblasts and fibroblasts growth. The membrane showed the ability to promote angiogenesis and enhance bone regeneration in vivo. An asymmetric collagen/chitosan GBR membrane can be fabricated by loading minocycline encapsulated chitosan nanoparticles, and shows satisfactory biocompatibility and barrier function, which enhances bone regeneration. Therefore, this antibacterial GBR membrane is a promising therapeutic approach to prevent infection and guide bone regeneration. PMID:27546177

  4. Localization and proliferation of lymphatic vessels in the tympanic membrane in normal state and regeneration.

    PubMed

    Miyashita, Takenori; Burford, James L; Hong, Young-Kwon; Gevorgyan, Haykanush; Lam, Lisa; Mori, Nozomu; Peti-Peterdi, Janos

    2013-10-25

    We clarified the localization of lymphatic vessels in the tympanic membrane and proliferation of lymphatic vessels during regeneration after perforation of the tympanic membrane by using whole-mount imaging of the tympanic membrane of Prox1 GFP mice. In the pars tensa, lymphatic vessel loops surrounded the malleus handle and annulus tympanicus. Apart from these locations, lymphatic vessel loops were not observed in the pars tensa in the normal tympanic membrane. Lymphatic vessel loops surrounding the malleus handle were connected to the lymphatic vessel loops in the pars flaccida and around the tensor tympani muscle. Many lymphatic vessel loops were detected in the pars flaccida. After perforation of the tympanic membrane, abundant lymphatic regeneration was observed in the pars tensa, and these regenerated lymphatic vessels extended from the lymphatic vessels surrounding the malleus at day 7. These results suggest that site-specific lymphatic vessels play an important role in the tympanic membrane.

  5. Water repellent Ag/Ag2O@bamboo cellulose fiber membrane as bioinspired cargo carriers.

    PubMed

    Wang, Yaru; Zhang, Ximu; Zhang, Xiaofang; Zhao, Jiangqi; Zhang, Wei; Lu, Canhui

    2015-11-20

    Water striders can walk on water. To mimic this function, a porous membrane consisted of bamboo cellulose fiber was hybridized with Ag/Ag2O nanoparticles through a facile in situ method to produce water repellent and well-ventilated materials. Herein, we report the sole surface roughness created by Ag/Ag2O nanoparticles could render the membrane a water contact angle (CA) of 140±3.0°. When floating on water, the hybrid membrane was able to support a heavy load more than 10 times the weight of the membrane itself. Additionally, this membrane demonstrated capabilities for oil sampling under water or oil/water separation and strong antibacterial activity against Escherichia coli. Thus we foresee that this novel hybrid membrane can be potentially utilized as drag-reducing, gas permeable and antibiotic substrates for constructing miniature aquatic devices.

  6. Electrospun cellulose acetate membrane for size separating and antibacterial screening of crude polysaccharides.

    PubMed

    Chumpol, Jiraporn; Siri, Sineenat

    2016-12-01

    This study aims to produce electrospun cellulose acetate (CA) membrane as the alternative supporting medium for a separation of crude polysaccharides by electrophoresis and a screening of their antibacterial activity. Among the tested conditions of fabrication, electrospun CA membrane at 57% porosity showed the best separation of each polysaccharide from the standard mixture and the crude extract of Aloe vera via electrophoresis. As compared with the commercial CA membrane, the produced electrospun CA membrane demonstrated more separated spots of polysaccharides. The antibacterial activity of the electrophoretic polysaccharide was also determined against Escherichia coli and Staphylococcus aureus as the inhibition zone after the bacterial culture agar was overlaid on the membrane and incubated for 24 h. The results of this study suggested the potential application of electrospun CA membrane combining with electrophoresis as a simple method for separating crude polysaccharides and screening for their antibacterial activity.

  7. Hydrophilicity and antifouling property of membrane materials from cellulose acetate/polyethersulfone in DMAc.

    PubMed

    Sun, Zhonghua; Chen, Fushan

    2016-10-01

    In this study, cellulose acetate (CA) was blended with polyethersulfone (PES) to endow the ultrafiltration membrane with the improved hydrophilicity and antifouling property by using N,N-dimethylacetamide (DMAc) as the solvent. The effects of blend composition and evaporation time on the mechanical strength and pure water flux were investigated. It was found that the optimal composition of the casting solution was: 18wt% (PES), 4wt% (Polyvinylpyrrolidone K30), 3wt% (CA) and 20s (Evaporation time). The characteristics of CA-PES blend membranes were investigated through the methods of contact angle goniometer, antifouling property, compatibility, thermo gravimetric analysis and SEM. The results showed that the hydrophilicity and antifouling property of CA-PES ultrafiltration membranes were enhanced in comparison with the pure PES membranes. The CA-PES membranes exhibited semi-compatibility and good thermal stability below 270°C. This study provided a potential industrial application prospect of CA-PES membranes prepared in DMAc.

  8. Preparation and properties of PLGA nanofiber membranes reinforced with cellulose nanocrystals.

    PubMed

    Mo, Yunfei; Guo, Rui; Liu, Jianghui; Lan, Yong; Zhang, Yi; Xue, Wei; Zhang, Yuanming

    2015-08-01

    Although extensively used in the fields of drug-carrier and tissue engineering, the biocompatibility and mechanical properties of polylactide-polyglycolide (PLGA) nanofiber membranes still limit their applications. The objective of this study was to improve their utility by introducing cellulose nanocrystals (CNCs) into PLGA nanofiber membranes. PLGA and PLGA/CNC composite nanofiber membranes were prepared via electrospinning, and the morphology and thermodynamic and mechanical properties of these nanofiber membranes were characterized by scanning electron microscopy (SEM), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA). The cytocompatibility and cellular responses of the nanofiber membranes were also studied by WST-1 assay, SEM, and confocal laser scanning microscopy (CLSM). Incorporation of CNCs (1, 3, 5, and 7 wt.%) increased the average fiber diameter of the prepared nanofiber membranes from 100 nm (neat PLGA) to ∼400 nm (PLGA/7 wt.% CNC) and improved the thermal stability of the nanofiber membranes. Among the PLGA/CNC composite nanofiber membranes, those loaded with 7 wt.% CNC nanofiber membranes had the best mechanical properties, which were similar to those of human skin. Cell culture results showed that the PLGA/CNC composite nanofiber membranes had better cytocompatibility and facilitated fibroblast adhesion, spreading, and proliferation compared with neat PLGA nanofiber membranes. These preliminary results suggest that PLGA/CNC composite nanofiber membranes are promising new materials for the field of skin tissue engineering.

  9. Effect of coagulant bath on the gas permeation properties of cellulose acetate asymmetric membrane

    NASA Astrophysics Data System (ADS)

    Mohamed, F.; Hasbullah, H.; Jami'an, W. N. R.; Salleh, W. N. H. W.; Ibrahim, N.; Ali, R. R.

    2016-06-01

    Membrane based gas separation process technology has been recognized as one of the most efficient and advanced unit operation for gas separation. One of the problems in membrane gas separation is membrane performance. This paper explores the application of cellulose acetate (CA) membrane for natural gas purification and separation by improving its permeability and selectivity. The main interest in this research is to study the effect of quench medium on the gas separation performance towards its physical characteristics and gas separation performance of CA membrane. Cellulose acetate polymer was dissolved in n- methyl-2-pyrrolidone solvent and casted onto a glass plate using a pneumatically controlled casting system with fixed shear rate and solvent evaporation times. The parameter varied was the non-solvent used as quench medium during membrane post treatment that were methanol and n-hexane. The different quench media as post treatment affected the O2 and N2 gas permeation and O2/N2 selectivity as well as the tensile strength of the flat sheet asymmetric membrane. Combination of methanol and n-hexane as quench media gave the best result than the other steps. This solvent exchange step influenced the morphology by producing thin skin layer and thus gives better gas separation performance than other steps

  10. Efficacy of Oxidized Regenerated Cellulose, SurgiGuard®, in Porcine Surgery

    PubMed Central

    Kim, Sung Hyun; Kim, Se Hoon; Yoon, Hye Sung; Kim, Hyun Kyoon

    2017-01-01

    Purpose Adequate hemostasis is important for postoperative outcomes of abdominal surgery. This study evaluated the hemostatic effects and accompanying histopathological changes of a novel oxidized regenerated cellulose, SurgiGuard®, during abdominal surgery. Materials and Methods Ten pigs underwent wedge resection of the spleen (1×1 cm) and liver (1.5×1.5 cm). The resected surface was covered with Surgicel® fabric or fibril type (Group A) or SurgiGuard® fabric or fibril type (Group B). Surgicel® and SurgiGuard® were randomized for attachment to the resected surface by fabric type (n=5) or fibril type (n=5). Blood loss was measured 5, 7, and 9 min after resection. Pigs were necropsied 6 weeks postoperatively to evaluate gross and histopathological changes. Results There was no significant difference in total blood loss between groups [spleen fabric: Group A vs. Group B, 4.38 g (2.74–6.43) vs. 3.41 g (2.46–4.65), p=0.436; spleen fibril: Group A vs. Group B, 3.44 g (2.82–6.07) vs. 3.60 g (2.03–6.09), p=0.971; liver fabric: Group A vs. Group B, 4.51 g (2.67–10.61) vs. 6.93 g (3.09–9.95), p=0.796; liver fibril: Group A vs. Group B, 3.32 g (2.50–8.78) vs. 3.70 g (2.32–5.84), p=0.971]. Histopathological analysis revealed no significant difference in toxicities related to Surgicel® or SurgiGuard® [inflammation, fibrosis, foreign bodies, and hemorrhage (spleen: p=0.333, 0.127, 0.751, and 1.000; liver: p=0.155, 0.751, 1.000, and 1.000, respectively)]. Conclusion SurgiGuard® is as effective and non-toxic as Surgicel® in achieving hemostasis after porcine abdominal surgery. PMID:27873514

  11. Microbial production of homogeneously layered cellulose pellicles in a membrane bioreactor.

    PubMed

    Hofinger, M; Bertholdt, G; Weuster-Botz, D

    2011-09-01

    Microbial cellulose (MC) is being investigated for various applications in the field of biomedical engineering. Gluconacetobacter xylinus is able to produce pure cellulose in the form of a hydrogel ("pellicle"). The pellicle consists of a defined tridimensional structure that is sensitive to mechanical stress during the process of formation. The bacteria, however, are obligate aerobic and need to be supplied with oxygen. These two objectives are often conflicting. A lab-scale membrane bioreactor prototype was developed which is able to efficiently produce a MC pellicle with a homogeneous layered structure. A hydrophilic microfiltration polyethersulfone membrane separates the bacteria from the cultivation medium. This setup allows the free convective exchange of the cultivation medium, while providing mechanical support for the continuous formation of the MC layer. Thickness of the MC layer was measured online by a laser triangulation sensor. One hundred and twenty five gram cellulose dry weight/m(2) membrane surface were produced within a process time of 330 h. Membrane bioreactors may be used to produce homogenous MC layers in a variety of shapes suitable for biomedical applications.

  12. Electrospinning of silver nanoparticles loaded highly porous cellulose acetate nanofibrous membrane for treatment of dye wastewater

    NASA Astrophysics Data System (ADS)

    Wang, Ke; Ma, Qian; Wang, Shu-Dong; Liu, Hua; Zhang, Sheng-Zhong; Bao, Wei; Zhang, Ke-Qin; Ling, Liang-Zhong

    2016-01-01

    In this paper, silver nanoparticles (NPs) were reduced form silver nitrate. Morphology and distribution of the synthesized silver NPs were characterized. In order to obtain cellulose acetate (CA), nanofibrous membrane with high effective adsorption performance to carry silver NPs for treatment of dye wastewater, different solvent systems were used to fabricate CA nanofibrous membranes with different morphologies and porous structures via electrospinning. Morphologies and structures of the obtained CA nanofibrous membranes were compared by scanning electron microscopy (SEM), which showed that CA nanofibrous membrane obtained from acetone/dichloromethane (1/2, v/v) was with the highly porous structure. SEM, energy-dispersive spectrometry and Fourier transform infrared spectrometry showed that the silver NPs were effectively incorporated in the CA nanofibrous membrane and the addition of silver NPs did not damage the porous structure of the CA nanofibrous membrane. Adsorption of dye solution (rhodamine B aqueous solution) revealed that the highly porous CA nanofibrous membrane exhibited effective adsorption performance and the addition of silver NPs did not affect the adsorption of the dye. Antibacterial property of the CA nanofibrous membrane showed that the silver-loaded highly porous CA nanofibrous membrane had remarkable antibacterial property when compared to the CA nanofibrous membrane without silver NPs. The silver-loaded highly porous CA nanofibrous membrane could be considered as an ideal candidate for treatment of the dye wastewater.

  13. Metal nanoparticle/ionic liquid/cellulose: new catalytically active membrane materials for hydrogenation reactions.

    PubMed

    Gelesky, Marcos A; Scheeren, Carla W; Foppa, Lucas; Pavan, Flavio A; Dias, Silvio L P; Dupont, Jairton

    2009-07-13

    Transition metal-containing membrane films of 10, 20, and 40 μm thickness were obtained by the combination of irregularly shaped nanoparticles with monomodal size distributions of 4.8 ± 1.1 nm (Rh(0)) and 3.0 ± 0.4 nm (Pt(0)) dispersed in the ionic liquid (IL) 1-n-butyl-3-methylimidazolium bis(trifluoromethane sulfonyl)imide (BMI·(NTf)(2)) with a syrup of cellulose acetate (CA) in acetone. The Rh(0) and Pt(0) metal concentration increased proportionally with increases in film thickness up to 20 μm, and then the material became metal saturated. The presence of small and stable Rh(0) or Pt(0) nanoparticles induced an augmentation in the CA/IL film surface areas. The augmentation of the IL content resulted in an increase of elasticity and decrease in tenacity and toughness, whereas the stress at break was not influenced. The introduction of IL probably causes an increase in the separation between the cellulose macromolecules that results in a higher flexibility, lower viscosity, and better formability of the cellulose material. The nanoparticle/IL/CA combinations exhibit an excellent synergistic effect that enhances the activity and durability of the catalyst for the hydrogenation of cyclohexene. The nanoparticle/IL/cellulose acetate film membranes display higher catalytic activity (up to 7353 h(-1) for the 20 μm film of CA/IL/Pt(0)) and stability than the nanoparticles dispersed only in the IL.

  14. Cellulose Acetate 398-10 Asymmetric Membrane Capsules for Osmotically Regulated Delivery of Acyclovir.

    PubMed

    Sonkar, Alka; Kumar, Anil; Pathak, Kamla

    2016-01-01

    The study was aimed at developing cellulose acetate asymmetric membrane capsules (AMCs) of acyclovir for its controlled delivery at the absorption site. The AMCs were prepared by phase inversion technique using wet process. A 2(3) full factorial design assessed the effect of independent variables (level(s) of polymer, pore former, and osmogen) on the cumulative drug release from AMCs. The buoyant optimized formulation F7 (low level of cellulose acetate; high levels of both glycerol and sodium lauryl sulphate) displayed maximum drug release of 97.88 ± 0.77% in 8 h that was independent of variation in agitational intensity and intentional defect on the cellulose acetate AMC. The in vitro data best fitted zero-order kinetics (r (2) = 0.9898). SEM micrograph of the transverse section confirmed the asymmetric nature of the cellulose acetate capsular membrane. Statistical analysis by Design Expert software indicated no interaction between the independent variables confirming the efficiency of the design in estimating the effects of variables on drug release. The optimized formulation F7 (desirability = 0.871) displayed sustenance of drug release over the drug packed in AMC in pure state proving the superiority of osmotically active formulation. Conclusively the AMCs have potential for controlled release of acyclovir at its absorption site.

  15. Cellulose film regenerated from Styela clava tunics have biodegradability, toxicity and biocompatibility in the skin of SD rats.

    PubMed

    Song, Sung Hwa; Kim, Ji Eun; Lee, Young Ju; Kwak, Moon Hwa; Sung, Geum Yong; Kwon, Soon Hong; Son, Hong Joo; Lee, Hee Seob; Jung, Young Jin; Hwang, Dae Youn

    2014-06-01

    Cellulose is one of the most widespread biomolecules in nature and has been exploited in various applications including scaffolding, tissue engineering, and tissue formation. To evaluate the biocompatibility of cellulose film manufactured from Styela clava tunics (SCT-CF), these films were implanted in Sprague-Dawley (SD) rats for various lengths of time, after which they were subjected to mechanical and biological analyses. The cellulose powders (12-268 m) obtained from SCT was converted into films via casting methods without adding any additives. SCT-CF contained about 98 % α-cellulose and very low concentrations of ββ-cellulose. Additionally, the crystallinity index (CrI) of SCT-CF was lower (10.71 %) than that of wood pulp-cellulose films (WP-CF) (33.78 %). After implantation for 90 days, the weight loss and formation of surface corrugations were greater in SCT-CF than that of WP-CF, while the surface roughness was significantly higher in WP-CF than SCT-CF. However, there were no differences in the number of white blood cells between SCT-CF implanted rats and vehicle implanted rats. The level of metabolic enzymes representing liver and kidney toxicity in the serum of SCT-CF implanted rats was maintained at levels consistent with vehicle implanted rats. Moreover, no significant alteration of the epidermal hyperplasia, inflammatory cell infiltration, redness, and edema were observed in SD rats implanted with SCT-CF. Taken together, these results indicate that SCT-CF showed good degradability and non-toxicity without inducing an immune response in SD rats. Further, the data presented here constitute strong evidence that SCT-CF has the potential for use as a powerful biomaterial for medical applications including stitching fiber, wound dressing, scaffolding, absorbable hemostats and hemodialysis membrane.

  16. Immobilization of collagen peptide on dialdehyde bacterial cellulose nanofibers via covalent bonds for tissue engineering and regeneration

    PubMed Central

    Wen, Xiaoxiao; Zheng, Yudong; Wu, Jian; Wang, Lu-Ning; Yuan, Zhenya; Peng, Jiang; Meng, Haoye

    2015-01-01

    Bacterial cellulose (BC) is an alternative nanostructured biomaterial to be utilized for a wide range of biomedical applications. Because of its low bioactivity, which restricted its practical application, collagen and collagen hydrolysate were usually composited into BC. It is necessary to develop a new method to generate covalent bonds between collagen and cellulose to improve the immobilization of collagen on BC. This study describes a facile dialdehyde BC/collagen peptide nanocomposite. BC was oxidized into dialdehyde bacterial cellulose (DBC) by regioselective oxidation, and then composited with collagen peptide (Col-p) via covalent bonds to form Schiff’s base type compounds, which was demonstrated by the results of microstructures, contact angle, Col-p content, and peptide-binding ratio. The peptide-binding ratio was further affected by the degree of oxidation, pH value, and zeta potential. In vitro desorption measurement of Col-p suggested a controlled release mechanism of the nanocomposite. Cell tests indicated that the prepared DBC/Col-p composite was bioactive and suitable for cell adhesion and attachment. This work demonstrates that the DBC/Col-p composite is a promising material for tissue engineering and regeneration. PMID:26229466

  17. Immobilization of collagen peptide on dialdehyde bacterial cellulose nanofibers via covalent bonds for tissue engineering and regeneration.

    PubMed

    Wen, Xiaoxiao; Zheng, Yudong; Wu, Jian; Wang, Lu-Ning; Yuan, Zhenya; Peng, Jiang; Meng, Haoye

    2015-01-01

    Bacterial cellulose (BC) is an alternative nanostructured biomaterial to be utilized for a wide range of biomedical applications. Because of its low bioactivity, which restricted its practical application, collagen and collagen hydrolysate were usually composited into BC. It is necessary to develop a new method to generate covalent bonds between collagen and cellulose to improve the immobilization of collagen on BC. This study describes a facile dialdehyde BC/collagen peptide nanocomposite. BC was oxidized into dialdehyde bacterial cellulose (DBC) by regioselective oxidation, and then composited with collagen peptide (Col-p) via covalent bonds to form Schiff's base type compounds, which was demonstrated by the results of microstructures, contact angle, Col-p content, and peptide-binding ratio. The peptide-binding ratio was further affected by the degree of oxidation, pH value, and zeta potential. In vitro desorption measurement of Col-p suggested a controlled release mechanism of the nanocomposite. Cell tests indicated that the prepared DBC/Col-p composite was bioactive and suitable for cell adhesion and attachment. This work demonstrates that the DBC/Col-p composite is a promising material for tissue engineering and regeneration.

  18. Optimal operating policy of the ultrafiltration membrane bioreactor for enzymatic hydrolysis of cellulose

    SciTech Connect

    Lee, SeungGoo; Kim, HakSung . Dept. of Biotechnology)

    1993-09-05

    The dilution rate of an ultrafiltration membrane bioreactor in the enzymatic hydrolysis of cellulose was optimized using the kinetic model developed by Fan and Lee.' The sequence of optimal dilution rates was found to generally consist of an initial period of a minimal value (batch period), a subsequent period of maximum dilution rate, a period of a second batch, and a final period of a singular dilution rate. The effects of operating conditions, such as [beta]-glucosidase activity, operating time, maximum dilution rate, substrate feeding rate, and enzyme-to-substrate ratio on both the conversion yield and the sequence of optimal dilution rates were investigated. To evaluate the validity of kinetic model employed in this work, enzymatic hydrolysis was carried out using -cellulose as a substrate in the ultrafiltration membrane bioreactor. The experimental data were well consistent with the simulation results.

  19. Synthesis of polymer electrolyte membranes from cellulose acetate/poly(ethylene oxide)/LiClO{sub 4} for lithium ion battery application

    SciTech Connect

    Nurhadini, Arcana, I Made

    2015-09-30

    This study was conducted to determine the effect of cellulose acetate on poly(ethylene oxide)-LiClO{sub 4} membranes as the polymer electrolyte. Cellulose acetate is used as an additive to increase ionic conductivity and mechanical property of polymer electrolyte membranes. The increase the percentage of cellulose acetate in membranes do not directly effect on the ionic conductivity, and the highest ionic conductivity of membranes about 5,7 × 10{sup −4} S/cm was observed in SA/PEO/LiClO{sub 4} membrane with cellulose ratio of 10-25% (w/w). Cellulose acetate in membranes increases mechanical strength of polymer electrolyte membranes. Based on TGA analysis, this polymer electrolyte thermally is stable until 270 °C. The polymer electrolyte membrane prepared by blending the cellulose acetate, poly(ethylene oxide), and lithium chlorate could be potentially used as a polymer electrolyte for lithium ion battery application.

  20. Synthesis of polymer electrolyte membranes from cellulose acetate/poly(ethylene oxide)/LiClO4 for lithium ion battery application

    NASA Astrophysics Data System (ADS)

    Nurhadini, Arcana, I. Made

    2015-09-01

    This study was conducted to determine the effect of cellulose acetate on poly(ethylene oxide)-LiClO4 membranes as the polymer electrolyte. Cellulose acetate is used as an additive to increase ionic conductivity and mechanical property of polymer electrolyte membranes. The increase the percentage of cellulose acetate in membranes do not directly effect on the ionic conductivity, and the highest ionic conductivity of membranes about 5,7 × 10-4 S/cm was observed in SA/PEO/LiClO4 membrane with cellulose ratio of 10-25% (w/w). Cellulose acetate in membranes increases mechanical strength of polymer electrolyte membranes. Based on TGA analysis, this polymer electrolyte thermally is stable until 270 °C. The polymer electrolyte membrane prepared by blending the cellulose acetate, poly(ethylene oxide), and lithium chlorate could be potentially used as a polymer electrolyte for lithium ion battery application.

  1. Succinate-bonded cellulose: a regenerable and powerful sorbent for cadmium-removal from spiked high-hardness groundwater.

    PubMed

    Belhalfaoui, Belkacem; Aziz, Abdellah; Elandaloussi, El Hadj; Ouali, Mohand Said; De Ménorval, Louis Charles

    2009-09-30

    The primary objective of this work was to evaluate a chemically modified cellulose for the sorption efficiency and selectivity to remove cadmium from spiked high-hardness groundwater. Heterogeneous esterification of cellulose with succinic anhydride in toluene under basic conditions has proceeded very efficiently to yield the succinylated cellulose (SC) with fairly high DS value, as confirmed by FTIR and solid-state MAS (13)C NMR spectroscopies. Deprotonation of the free carboxylic acid group was achieved by alkaline treatment of SC with saturated NaHCO(3) aqueous solution. Batch experiments were carried out on the resulting sodic material (NaSC) to examine its cadmium-removing capability in both distilled water (DW) and spiked groundwater (GW). The results obtained from the sorption characteristics (kinetics, isotherms and pH effect) have revealed that NaSC material is particularly effective in removing cadmium from both DW and GW solutions, with a maximum uptake of 185.2 and 178.6 mg g(-1), respectively. These comparable sorption capacities strongly suggest that NaSC sorbent is highly selective to heavy metal over alkaline earth cations (Ca(2+) and Mg(2+)) and therefore less susceptible to interference from background ions, naturally present in groundwater. On the other hand, cadmium sorption is shown to decrease with a decrease in pH which is indubitably inherent to the competing proton during the ion-exchange process. Furthermore, the material has proven to be efficiently regenerable by using a NaCl brine solution. Thus, the use of the sorbent sequentially to the first regeneration led to nearly no attenuation in the material's capacity for cadmium-removal. Finally, the sorption effectiveness of NaSC is compared to those of other low-cost sorbents so far reported in the literature.

  2. Surface-modified anodic aluminum oxide membrane with hydroxyethyl celluloses as a matrix for bilirubin removal.

    PubMed

    Xue, Maoqiang; Ling, Yisheng; Wu, Guisen; Liu, Xin; Ge, Dongtao; Shi, Wei

    2013-01-01

    Microporous anodic aluminum oxide (AAO) membranes were modified by 3-glycidoxypropyltrimethoxysilane to produce terminal epoxy groups. These were used to covalently link hydroxyethyl celluloses (HEC) to amplify reactive groups of AAO membrane. The hydroxyl groups of HEC-AAO composite membrane were further modified with 1,4-butanediol diglycidyl ether to link arginine as an affinity ligand. The contents of HEC and arginine of arginine-immobilized HEC-AAO membrane were 52.1 and 19.7mg/g membrane, respectively. As biomedical adsorbents, the arginine-immobilized HEC-AAO membranes were tested for bilirubin removal. The non-specific bilirubin adsorption on the unmodified HEC-AAO composite membranes was 0.8mg/g membrane. Higher bilirubin adsorption values, up to 52.6mg/g membrane, were obtained with the arginine-immobilized HEC-AAO membranes. Elution of bilirubin showed desorption ratio was up to 85% using 0.3M NaSCN solution as the desorption agent. Comparisons equilibrium and dynamic capacities showed that dynamic capacities were lower than the equilibrium capacities. In addition, the adsorption mechanism of bilirubin and the effects of temperature, initial concentration of bilirubin, albumin concentration and ionic strength on adsorption were also investigated.

  3. Comparison of diffusion by anionic surfactants through cellulose acetate and collagen membranes.

    PubMed

    García Ramón, M T; Ribosa, I; Leal, J S; Parra, J L

    1989-06-01

    Synopsis From a dermatological point of view, it is important to know what is the irritation potential of surfactants on human skin. Recent research trends have been oriented towards the establishment of new 'in vitro' techniques that will avoid animal experimentation. In this paper, some results on the rate of diffusion of different anionic surfactants through both cellulose acetate and collagen membranes are described. A correlation between results of diffusion through the protein membrane and results published on the same surfactants and their irritation potential during 'in vivo' experiments appears possible.

  4. Adsorption of N-alkylpyridinium chlorides from water and salt solutions on cellulose acetate ultrafiltration membranes

    SciTech Connect

    Klimenko, N.A.; Yaroshenko, N.A.; Kondratova, T.B.

    1988-09-01

    A study has been made of the adsorption of three homologues in the N-alkylpyridinium chloride series from water and salt solutions, over a wide range of concentrations, on cellulose acetate ultrafiltration membranes, Grades UAM-500 and UAM-150. When adsorption takes place from true solutions, the membrane surface is hydrophobized. In the region of micellar solutions, nonassociated molecules and micelles are adsorbed in the mesopores and supermicropores, forming a mosaic adsorption layer. The thickness of the modifying layer depends on the length of the hydrophobic radical and on the composition of the system.

  5. Synergistic Effect of Functionalized Nanokaolin Decorated MWCNTs on the Performance of Cellulose Acetate (CA) Membranes Spectacular.

    PubMed

    Afzal, Amina; Rafique, Muhammad Shahid; Iqbal, Nadeem; Qaiser, Asif Ali; Anwar, Abdul Waheed; Iqbal, Sadia Sagar

    2016-04-21

    In order to enhance salt rejection level and high pressure mechanical integrity, functionalized nanokaolin decorated multiwall carbon nanotubes (FNKM, 0-5 wt % loading) were incorporated into a cellulose acetate (CA) matrix using high temperature solution mixing methodology. Scanning electron microscopy (SEM), X-ray diffraction technique (XRD), thermo-gravimetric analyzer (TGA) and Fourier transform infrared spectrometer (FTIR) were used to characterize the prepared membranes. The obtained results revealed that with increasing FNKM concentration in the host polymeric matrix, composite membrane's structural, functional, thermal, water permeation/flux and salt rejection characteristics were also modified accordingly. Percent enhancement in salt rejection was increased around threefold by adding 5 wt % FNKM in CA.

  6. Localization and proliferation of lymphatic vessels in the tympanic membrane in normal state and regeneration

    SciTech Connect

    Miyashita, Takenori; Burford, James L.; Hong, Young-Kwon; Gevorgyan, Haykanush; Lam, Lisa; Mori, Nozomu; Peti-Peterdi, Janos

    2013-10-25

    Highlights: •We newly developed the whole-mount imaging method of the tympanic membrane. •Lymphatic vessel loops were localized around the malleus handle and annulus tympanicus. •In regeneration, abundant lymphatic vessels were observed in the pars tensa. •Site-specific lymphatic vessels may play an important role in the tympanic membrane. -- Abstract: We clarified the localization of lymphatic vessels in the tympanic membrane and proliferation of lymphatic vessels during regeneration after perforation of the tympanic membrane by using whole-mount imaging of the tympanic membrane of Prox1 GFP mice. In the pars tensa, lymphatic vessel loops surrounded the malleus handle and annulus tympanicus. Apart from these locations, lymphatic vessel loops were not observed in the pars tensa in the normal tympanic membrane. Lymphatic vessel loops surrounding the malleus handle were connected to the lymphatic vessel loops in the pars flaccida and around the tensor tympani muscle. Many lymphatic vessel loops were detected in the pars flaccida. After perforation of the tympanic membrane, abundant lymphatic regeneration was observed in the pars tensa, and these regenerated lymphatic vessels extended from the lymphatic vessels surrounding the malleus at day 7. These results suggest that site-specific lymphatic vessels play an important role in the tympanic membrane.

  7. The wettability of a cellulose acetate membrane in the presence of bovine serum albumin

    NASA Astrophysics Data System (ADS)

    Białopiotrowicz, Tomasz; Jańczuk, Bronisław

    2002-11-01

    The measurements of the contact angle for water (W), glycerol (G), formamide (F), ethylene glycol (E) and diiodomethane (D) on a bare cellulose acetate membrane and covered by adsorptive bovine serum albumin (BSA) films were made. The adsorption was performed from solutions in concentration range 0-100 mg/ml. An influence of the membrane porosity on an apparent contact angle was discussed and Cassie and Baxter equation was used for that purpose. It was suggested that some liquids could penetrate in to membrane pores reducing its apparent porosity. To explain such behaviour, the spreading coefficient and the work of adhesion was calculated for the studied liquids. Components and parameters of the surface free energy of a bare cellulose acetate membrane and covered by an adsorptive BSA film were determined for W-G-D, W-F-D and G-F-D three-liquid systems and they were similar for these systems. However, for the hydrated BSA layer those components and parameters for the systems W-G-D, W-F-D were different than those for the system G-F-D. It was stated that after BSA adsorption on that membrane percentage of empty pores decreased, reducing their number almost to 0, at the highest BSA concentrations.

  8. Recent advances in cellulose and chitosan based membranes for water purification: A concise review.

    PubMed

    Thakur, Vijay Kumar; Voicu, Stefan Ioan

    2016-08-01

    Recently membrane technology has emerged as a new promising and pervasive technology due to its innate advantages over traditional technologies such as adsorption, distillation and extraction. In this article, some of the recent advances in developing polymeric composite membrane materials for water purification from natural polysaccharide based polymers namely cellulose derivatives and chitosan are concisely reviewed. The impact of human social, demographic and industrial evolution along with expansion through environment has significantly affected the quality of water by pollution with large quantities of pesticides, minerals, drugs or other residues. At the forefront of decontamination and purification techniques, we found the membrane materials from polymers as a potential alternative. In an attempt to reduce the number of technical polymers widely used in the preparation of membranes, many researchers have reported new solutions for desalination or retention of organic yeasts, based on bio renewable polymers like cellulose derivatives and chitosan. These realizations are presented and discussed in terms of the most important parameters of membrane separation especially water flux and retention in this article.

  9. Fabrication and performance of PET mesh enhanced cellulose acetate membranes for forward osmosis.

    PubMed

    Li, Guoliang; Wang, Jun; Hou, Deyin; Bai, Yu; Liu, Huijuan

    2016-07-01

    Polyethylene terephthalate mesh (PET) enhanced cellulose acetate membranes were fabricated via a phase inversion process. The membrane fabrication parameters that may affect the membrane performance were systematically evaluated including the concentration and temperature of the casting polymer solution and the temperature and time of the evaporation, coagulation and annealing processes. The water permeability and reverse salt flux were measured in forward osmosis (FO) mode for determination of the optimal membrane fabrication conditions. The optimal FO membrane shows a typical asymmetric sandwich structure with a mean thickness of about 148.2μm. The performance of the optimal FO membrane was tested using 0.2mol/L NaCl as the feed solution and 1.5mol/L glucose as the draw solution. The membrane displayed a water flux of 3.47L/(m(2)·hr) and salt rejection of 95.48% in FO mode. While in pressure retarded osmosis (PRO) mode, the water flux was 4.74L/(m(2)·hr) and salt rejection 96.03%. The high ratio of water flux in FO mode to that in PRO mode indicates that the fabricated membrane has a lower degree of internal concentration polarization than comparable membranes.

  10. Alginate fouling reduction of functionalized carbon nanotube blended cellulose acetate membrane in forward osmosis.

    PubMed

    Choi, Hyeon-Gyu; Son, Moon; Yoon, SangHyeon; Celik, Evrim; Kang, Seoktae; Park, Hosik; Park, Chul Hwi; Choi, Heechul

    2015-10-01

    Functionalized multi-walled carbon nanotube blended cellulose acetate (fCNT-CA) membranes were synthesized for forward osmosis (FO) through phase inversion. The membranes were characterized through SEM, FTIR, and water contact angle measurement. AFM was utilized to investigate alginate fouling mechanism on the membrane. It reveals that the fCNT contributes to advance alginate fouling resistance in FO (57% less normalized water flux decline for 1% fCNT-CA membrane was observed than that for bare CA membrane), due to enhanced electrostatic repulsion between the membrane and the alginate foulant. Furthermore, it was found that the fCNT-CA membranes became more hydrophilic due to carboxylic groups in functionalized carbon nanotube, resulting in approximately 50% higher water-permeated flux than bare CA membrane. This study presents not only the fabrication of fCNT-CA membrane and its application to FO, but also the quantification of the beneficial role of fCNT with respect to alginate fouling in FO.

  11. Effect of evaporation time on cellulose acetate membrane for gas separation

    NASA Astrophysics Data System (ADS)

    Jami'an, W. N. R.; Hasbullah, H.; Mohamed, F.; Yusof, N.; Ibrahim, N.; Ali, R. R.

    2016-06-01

    Throughout this decades, membrane technology has been the desirable option among the others gas separation technologies. However, few issues have been raised regarding the membrane gas separation application including the trade-off between its permeability and selectivity and also its effects towards environment. Therefore, for this research, a biopolymer membrane for gas separation application will be developed with reasonably high on both permeability and selectivity. The main objective of this research is to study the effect of solvent evaporation time on the flat sheet asymmetric membrane morphology and gas separation performance. The membranes were produced by a simple dry/wet phase inversion technique using a pneumatically controlled casting system. The dope solution for the membrane casting was prepared by dissolving the cellulose acetate (CA) polymer in N-Methyl-2-pyrrolidone (NMP) and the solvent evaporation time was varied. Permeability and selectivity of the membrane was performed by using pure gases of carbon dioxide, CO2 and methane, CH4. The increase in solvent evaporation time had improved the membrane morphologies as the porosity of the membrane surface decrease and formation of a more mature skin layer. The gas permeation tests determined that increasing in solvent evaporation time had increased the selectivity of CO2/CH4 but reduce the permeability of both gases

  12. Separation of macromolecular proteins and removal of humic acid by cellulose acetate modified UF membranes.

    PubMed

    Kanagaraj, P; Nagendran, A; Rana, D; Matsuura, T

    2016-08-01

    Surface modifying macromolecules (SMMs) were synthesized with various polyurethane pre polymers end-capped with different groups and blended into the casting solution of cellulose acetate (CA) to prepare surface modified ultra-filtration (UF) membranes for water filtration applications. The surface modification of the CA membranes was confirmed by the FTIR and static contact angle (SCA) measurements. The membranes so prepared had the typical characteristics of UF membranes as confirmed by scanning electron microscopy (SEM). Membrane properties were studied in terms of membrane compaction, percentage water content (%WC), pure water flux (PWF), membrane hydraulic resistance (Rm), molecular weight cut-off (MWCO), average pore size and porosity. The result showed that PWF, %WC, MWCO and pore size increased whereas the Rm decreased by the addition of SMMs. The significant effect of SMMs on the fouling by humic acid (HA) was also observed. It was found that the cSMM-3 membrane, in which SMM was synthesized with diethylene glycol (DEG) and hydroxyl benzene sulfonate (HBS) was blended, had the highest flux recovery ratio FRR (84.6%), as well as the lowest irreversible fouling (15.4%), confirming their improved antifouling properties. Thus, the SMM modified CA membranes had proven, to play an important role in the water treatment by UF.

  13. Effect of silica particle size in cellulose membrane for desalination process

    NASA Astrophysics Data System (ADS)

    Nurkhamidah, Siti; Rahmawati, Yeni; Taufany, Fadlilatul; Merta, I. Made Pendi Adi; Putra, Deffry Danius Dwi; Woo, Eamor M.

    2015-12-01

    Development of desalination technologies is very important for fulfilling future water demand. The objective of this research is to synthesis membrane for desalination process from cellulose acetate (CA) by blending with polyethylene glycol (PEG) and silica resulting CA/PEG/Silica composite membrane. In this study, the synthesis and characterization of composite membrane is attempt where membrane performance is investigated for reverse osmosis desalination of saline water. CA/PEG membrane with ratio 80/20 (wt%) was modified with three different particle sizes of silica: 0.007, 0.02, and 60 µm. Composite membranes were characterized for their hydrophilicity, functional groups and permeation properties. The experiment results show that hydrophilicity of CA/PEG membrane increases after the addition of silica as shown by the decreasing of contact angle and the increasing of silanol group. Hydrophilicity of composite membrane increases with the decreasing of particle size of silica. The best performance membrane is obtained by using silica with particle size of 0.02 µm.

  14. Guided Tissue Regeneration Using a Barrier Membrane in Endodontic Surgery.

    PubMed

    Corbella, Stefano; Taschieri, Silvio; Elkabbany, Ahmed; Del Fabbro, Massimo; von Arx, Thomas

    2016-01-01

    Endodontic surgery aims at the resolution of a periapical inflammatory process by surgical access followed by enucleation of the lesion and root-end filling to curb any potentially noxious agent within the physical confines of the affected root. Guided bone regeneration could be associated to endodontic surgery aiming to enhance periradicular tissue regeneration. The objective of this paper was to review the scientific literature about guided bone regeneration in endodontic surgery, evaluating the effects on periapical lesion healing process. The included articles are classified considering the anatomical characteristics of the lesion. Fourteen articles were included in the review after abstract and title selection. Eight articles were on studies on lesions affecting only the periapical region (three about through-and-through lesions) while six were about the treatment of apico-marginal lesions. On the basis of the currently available literature, there is a low scientific evidence of a benefit related. to the use of guided bone regeneration procedure in endodontic surgery.

  15. Low thrombogenicity of polyethylene glycol-grafted cellulose membranes does not influence heparin requirements in hemodialysis.

    PubMed

    Wright, M J; Woodrow, G; Umpleby, S; Hull, S; Brownjohn, A M; Turney, J H

    1999-07-01

    Heparin is the most commonly used anticoagulant for hemodialysis despite potentially serious side effects. Polyethylene glycol-grafted cellulose (PGC) membranes produce less activation of the coagulation cascade than cuprophane membranes. Anecdotally, we found some patients required a surprisingly low level of anticoagulation using these membranes. We compared the anticoagulant requirement of the PGC membrane with that of the cuprophane membrane in this randomized, prospective, crossover study. Sixty-three patients were randomized to treatment using either membrane, and heparin administration was progressively reduced to the lowest dose that prevented visible clotting in excess of that normally encountered. Patients underwent dialysis at this dose for 1 month, after which the heparin requirement and Kt/Vurea (1.162 x ln [urea pre/urea post]) were assessed. This process was then repeated for each patient using the other membrane, and the results were compared. Heparin administration during dialysis was reduced from a mean loading dose of 29.0 +/- 9.4 to 1.5 +/- 3.2 IU/kg for both membranes and a mean maintenance infusion of 14.0 +/- 6.7 to 0.77 +/- 1.6 IU/kg/h for both membranes (both P < 0.0001 v full anticoagulation; no difference between membranes). The Kt/Vurea was not significantly altered. Forty-six patients with PGC and 45 patients with cuprophane membranes underwent dialysis successfully without heparin during dialysis, and the other patients were using considerably reduced doses. Aspirin and warfarin had no effect on the heparin requirement. These results do not support the theory that PGC membranes have a lower anticoagulant requirement than cuprophane membranes; however, they suggest that dialysis can be performed successfully with much smaller anticoagulant doses than are currently in common use.

  16. Exploration of zwitterionic cellulose acetate antifouling ultrafiltration membrane for bovine serum albumin (BSA) separation.

    PubMed

    Liu, Yang; Huang, Haitao; Huo, Pengfei; Gu, Jiyou

    2017-06-01

    This study focused on the preparation of a new kind of membrane material, zwitterionic cellulose acetate (ZCA), via a three-step procedure consist of oxidization, Schiff base and quaternary amination reaction, and the fabrication of antifouling ZCA ultrafiltration membrane by the non-solvent-induced phase separation method (NIPS). The morphologies, surface chemical structures and compositions of the obtained CA and ZCA membranes were thoroughly characterized by field emission scanning electron microscopy (FE-SEM) with energy dispersive X-ray (EDX) spectroscopy, Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS), respectively. Meanwhile, the thermal stability, porosity and average pore size of two investigated membranes were also studied. As a result, the ZCA membrane displayed significantly improved hydrophilicity and water permeability compared with those of the reference CA membrane, despite a slight decrease in the protein rejection ratio. According to the cycle ultrafiltration performance of bovine serum albumin (BSA) solution and protein adsorption experiment, ZCA membrane exhibited better flux recovery property and fouling resistant ability, especially irreversible fouling resistant ability, suggesting superior antifouling performance. This new approach gives polymer-based membrane a long time life and excellent ultrafiltration performance, and seems promising for potential applications in the protein separation.

  17. Enzymatic degradation of collagen-guided tissue regeneration membranes by periodontal bacteria.

    PubMed

    Sela, Michael N; Kohavi, David; Krausz, Emanuela; Steinberg, Doron; Rosen, Graciela

    2003-06-01

    Bacterial infection in the vicinity of guided tissue regeneration barrier membranes was shown to have a negative effect on the clinical outcomes of this increasingly used technique. Several oral and specifically periodontal bacteria were shown to adhere to such membranes in vivo and in vitro with a higher affinity to membranes constructed from collagen. The present study examined the role of periodontal bacteria and their enzymes in the degradation of commercially used collagen membranes. Degradation of two collagen membranes [Biomend (Calcitek, Colla-Tec Inc., Plainsboro, NJ) and Bio-Gide (Geistlich Biomaterials, Wolhousen, Switzerland)] labeled by fluorescein isothiocyanate was examined by measuring soluble fluorescence. Porphyromonas gingivalis, Treponema denticola and Actinobacillus actinomycetemcomitans and their enzymes were evaluated. Collagenase from Clostridium hystolyticum was used as a positive control. While whole cells of P. gingivalis were able to degrade both types of membranes, T. denticola could degrade Bio-Gide membranes only and A. actinomycetemcomitans whole cells could degrade none of the membranes. Fractionation of P. gingivalis cells revealed that cell membrane associated proteases were responsible for the degradation of the two collagen membranes. In T. denticola, the purified major phenylalanine protease was found to be responsible for the degradation of Bio-Gide membranes. These results suggest that proteolytic bacterial enzymes may take part in the degradation of collagen barrier membranes used for guided tissue regeneration.

  18. High-speed water sterilization using silver-containing cellulose membranes

    NASA Astrophysics Data System (ADS)

    Sinclair, Terica; Zieba, Maciej; Irusta, Silvia; Sebastián, Víctor; Arruebo, Manuel

    2014-08-01

    The removal of bacteria and other pathogenic micro-organisms from drinking water is usually carried out by boiling; however, when this is not a feasible option, a combination of treatment based on filtration and disinfection is recommended. In this work, we produced cellulose filters grafted with silver nanoparticles (AgNPs) and silver nanowires (AgNWs) by covalent attachment of separately prepared Ag nanostructures on thiol- and amine-modified commercially available cellulosic filters. Results obtained from scanning electron microscopy (SEM), scanning transmission electron microscopy (STEM), and energy-dispersive X-ray spectroscopy (EDS) all revealed that such modified cellulose membranes contained large amounts of homogeneously dispersed AgNPs, whereas X-ray photoelectron spectroscopy (XPS) analysis demonstrated that the aforementioned nanostructures were immobilized on the membrane with a strong and stable covalent bond between the thiol or amine groups and the surface of the Ag nanofillers. This durable and robust covalent attachment facilitated outstanding suppression of the uncontrolled release of the nanostructures from the membranes, even under strong ultrasonication. Those membranes also demonstrated high permeance and antimicrobial activity in excess of 99.9% growth inhibition against Escherichia coli, which was used as a model of gram-negative coliform bacteria. Bacteria percolated throughout the tortuous silver-loaded filters, thus increasing the chances of contact between the Ag nanostructures (wires or nanoparticles) and the passing bacteria. Thus, we anticipate that these filters, with their high antibacterial activity and robustness, can be produced in a cost-effective manner and that they would be capable of producing affordable, clean, and safe drinking water in a short period of time without producing an uncontrolled silver release into the percolated water.

  19. High-speed water sterilization using silver-containing cellulose membranes.

    PubMed

    Sinclair, Terica; Zieba, Maciej; Irusta, Silvia; Sebastián, Víctor; Arruebo, Manuel

    2014-08-01

    The removal of bacteria and other pathogenic micro-organisms from drinking water is usually carried out by boiling; however, when this is not a feasible option, a combination of treatment based on filtration and disinfection is recommended. In this work, we produced cellulose filters grafted with silver nanoparticles (AgNPs) and silver nanowires (AgNWs) by covalent attachment of separately prepared Ag nanostructures on thiol- and amine-modified commercially available cellulosic filters. Results obtained from scanning electron microscopy (SEM), scanning transmission electron microscopy (STEM), and energy-dispersive X-ray spectroscopy (EDS) all revealed that such modified cellulose membranes contained large amounts of homogeneously dispersed AgNPs, whereas X-ray photoelectron spectroscopy (XPS) analysis demonstrated that the aforementioned nanostructures were immobilized on the membrane with a strong and stable covalent bond between the thiol or amine groups and the surface of the Ag nanofillers. This durable and robust covalent attachment facilitated outstanding suppression of the uncontrolled release of the nanostructures from the membranes, even under strong ultrasonication. Those membranes also demonstrated high permeance and antimicrobial activity in excess of 99.9% growth inhibition against Escherichia coli, which was used as a model of gram-negative coliform bacteria. Bacteria percolated throughout the tortuous silver-loaded filters, thus increasing the chances of contact between the Ag nanostructures (wires or nanoparticles) and the passing bacteria. Thus, we anticipate that these filters, with their high antibacterial activity and robustness, can be produced in a cost-effective manner and that they would be capable of producing affordable, clean, and safe drinking water in a short period of time without producing an uncontrolled silver release into the percolated water.

  20. Thin and flexible bio-batteries made of electrospun cellulose-based membranes.

    PubMed

    Baptista, A C; Martins, J I; Fortunato, E; Martins, R; Borges, J P; Ferreira, I

    2011-01-15

    The present work proposes the development of a bio-battery composed by an ultrathin monolithic structure of an electrospun cellulose acetate membrane, over which was deposited metallic thin film electrodes by thermal evaporation on both surfaces. The electrochemical characterization of the bio-batteries was performed under simulated body fluids like sweat and blood plasma [salt solution--0.9% (w/w) NaCl]. Reversible electrochemical reactions were detected through the cellulose acetate structure. Thus, a stable electrochemical behavior was achieved for a bio-battery with silver and aluminum thin films as electrodes. This device exhibits the ability to supply a power density higher than 3 μW cm(-2). Finally, a bio-battery prototype was tested on a sweated skin, demonstrating the potential of applicability of this bio-device as a micropower source.

  1. Visualization of Biomass Solubilization and Cellulose Regeneration during Ionic Liquid Pretreatment of Switchgrass

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Auto-fluorescent mapping of plant cell walls was used to visualize cellulose and lignin in pristine switchgrass (Panicum virgatum) stems to determine the mechanisms of biomass dissolution during ionic liquid pretreatment. The addition of ground switchgrass to the ionic liquid 1-n-ethyl-3-methylimid...

  2. FTIR, XRD and DSC studies of nanochitosan, cellulose acetate and polyethylene glycol blend ultrafiltration membranes.

    PubMed

    Vinodhini, P Angelin; K, Sangeetha; Thandapani, Gomathi; P N, Sudha; Jayachandran, Venkatesan; Sukumaran, Anil

    2017-03-29

    In the present work, a series of novel nanochitosan/cellulose acetate/polyethylene glycol (NCS/CA/PEG) blend flat sheet membranes were fabricated in different ratios (1:1:1, 1:1:2, 2:1:1, 2:1:2, 1:2:1, 2:2:1) in a polar solvent of N,N'-dimethylformamide (DMF) using the most popular phase inversion method. Nanochitosan was prepared by the ionotropic gelation method and its average particle size has been analyzed using Dynamic Light Scattering (DLS) method. The effect of blending of the three polymers was investigated using FTIR and XRD studies. FTIR results confirmed the formation of well-blended membranes and the XRD analysis revealed enhanced amorphous nature of the membrane ratio 2:1:2. DSC study was conducted to find out the thermal behavior of the blend membranes and the results clearly indicated good thermal stability and single glass transition temperature (Tg) of all the prepared membranes. Asymmetric nature and rough surface morphology was confirmed using SEM analysis. From the results it was evident that the blending of the polymers with higher concentration of nanochitosan can alter the nature of the resulting membranes to a greater extent and thus amorphous membranes were obtained with good miscibility and compatibility.

  3. Dehydration of water/pyridine mixtures by pervaporation using cellulose acetate/ polyacrylonitrile blend membrane.

    PubMed

    Lv, J H; Xiao, G M

    2011-01-01

    Cellulose acetate/ polyacrylonitrile (CA/PAN) membranes were prepared and used to separate pyridine / water mixtures by pervaporation. The membranes were characterized through SEM. The effects of feed concentration, operation temperature and downstream pressure on the separation performance were evaluated. Experimental results indicated the increase of operation temperature could raise the permeation flux and the separation factor, while increasing feed concentration and downstream pressure would raise the separation factor and decrease the permeation flux. Under the conditions that pyridine solution was 99 wt.%, operation temperature was 323 K and downstream pressure was 20 mmHg, the CA/PAN blend membrane showed its best separation performance that the permeation flux was 56.g.m-2 h-1 and the separation factor was 182.

  4. High-density polytetrafluoroethylene membranes in guided bone and tissue regeneration procedures: a literature review.

    PubMed

    Carbonell, J M; Martín, I Sanz; Santos, A; Pujol, A; Sanz-Moliner, J D; Nart, J

    2014-01-01

    Expanded polytetrafluoroethylene (e-PTFE) has been used successfully as a membrane barrier for regeneration procedures. However, when exposed to the oral cavity, its high porosity increases the risk of early infection, which can affect surgical outcomes. An alternative to e-PTFE is non-expanded and dense polytetrafluoroethylene (n-PFTE), which results in lower levels of early infection following surgical procedures. The aim of this literature review was to analyze and describe the available literature on n-PFTE, report the indications for use, advantages, disadvantages, surgical protocols, and complications. The medical databases Medline-PubMed and Cochrane Library were searched and supplemented with a hand search for reports published between 1980 and May 2012 on n-PTFE membranes. The search strategy was limited to animal, human, and in vitro studies in dental journals published in English. Twenty-four articles that analyzed the use of n-PTFE as a barrier membrane for guided tissue regeneration and guided bone regeneration around teeth and implants were identified: two in vitro studies, seven experimental studies, and 15 clinical studies. There is limited clinical and histological evidence for the use of n-PTFE membranes at present, with some indications in guided tissue regeneration and guided bone regeneration in immediate implants and fresh extraction sockets.

  5. Electrospun cellulose acetate composites containing supported metal nanoparticles for antifungal membranes.

    PubMed

    Quirós, Jennifer; Gonzalo, Soledad; Jalvo, Blanca; Boltes, Karina; Perdigón-Melón, José Antonio; Rosal, Roberto

    2016-09-01

    Electrospun cellulose acetate composites containing silver and copper nanoparticles supported in sepiolite and mesoporous silica were prepared and tested as fungistatic membranes against the fungus Aspergillus niger. The nanoparticles were in the 3-50nm range for sepiolite supported materials and limited by the size of mesopores (5-8nm) in the case of mesoporous silica. Sepiolite and silica were well dispersed within the fibers, with larger aggregates in the micrometer range, and allowed a controlled release of metals to create a fungistatic environment. The effect was assessed using digital image analysis to evaluate fungal growth rate and fluorescence readings using a viability stain. The results showed that silver and copper nanomaterials significantly impaired the growth of fungi when the spores were incubated either in direct contact with particles or included in cellulose acetate composite membranes. The fungistatic effect took place on germinating spores before hyphae growth conidiophore formation. After 24h the cultures were separated from fungistatic materials and showed growth impairment only due to the prior exposure. Growth reduction was important for all the particles and membranes with respect to non-exposed controls. The effect of copper and silver loaded materials was not significantly different from each other with average reductions around 70% for bare particles and 50% for membranes. Copper on sepiolite was particularly efficient with a decrease of metabolic activity of up to 80% with respect to controls. Copper materials induced rapid maturation and conidiation with fungi splitting in sets of subcolonies. Metal-loaded nanomaterials acted as reservoirs for the controlled release of metals. The amount of silver or copper released daily by composite membranes represented roughly 1% of their total load of metals. Supported nanomaterials encapsulated in nanofibers allow formulating active membranes with high antifungal performance at the same time

  6. Bacterial cellulose membranes used as artificial substitutes for dural defection in rabbits.

    PubMed

    Xu, Chen; Ma, Xia; Chen, Shiwen; Tao, Meifeng; Yuan, Lutao; Jing, Yao

    2014-06-16

    To improve the efficacy and safety of dural repair in neurosurgical procedures, a new dural material derived from bacterial cellulose (BC) was evaluated in a rabbit model with dural defects. We prepared artificial dura mater using bacterial cellulose which was incubated and fermented from Acetobacter xylinum. The dural defects of the rabbit model were repaired with BC membranes. All surgeries were performed under sodium pentobarbital anesthesia, and all efforts were made to minimize suffering. All animals were humanely euthanized by intravenous injection of phenobarbitone, at each time point, after the operation. Then, the histocompatibility and inflammatory effects of BC were examined by histological examination, real-time fluorescent quantitative polymerase chain reaction (PCR) and Western Blot. BC membranes evenly covered the surface of brain without adhesion. There were seldom inflammatory cells surrounding the membrane during the early postoperative period. The expression of inflammatory cytokines IL-1β, IL-6 and TNF-α as well as iNOS and COX-2 were lower in the BC group compared to the control group at 7, 14 and 21 days after implantation. BC can repair dural defects in rabbit and has a decreased inflammatory response compared to traditional materials. However, the long-term effects need to be validated in larger animals.

  7. Development of cellulose-polypyrrole microfiber membranes and assessment of their capability on water softening

    NASA Astrophysics Data System (ADS)

    Barrera, C.; Arrieta, A.; Escobar, N.; Gañan, P.; Castro, C.

    2013-11-01

    The application of conducting polymer composite for water softening is based on the use of pyrrole's electrochemical properties joined with the flexibility and relatively high surface areas associated with cellulose fibers, to develop a new hybrid material that exhibits the inherent proprieties of both components. This hybrid would allow to promote an ion exchange reaction between the composite membrane and the hard water. The cellulose membranes obtained from banana plant agricultural waste (raquis), were uniform with individual and well separated fibers. The fibers were encapsulated by a continuous coating of polypyrrole by an in situ oxidative chemical polymerization. The amount of polypyrrole deposited on the fiber increased by increasing the monomer concentration, behavior that was identified through the observation of differences on the intensity of the light to dark color shift that coated the fibers after the polymerization. The ion removal capability of the membrane coted with the conducting polymer was tested using an experimental device, finding reductions on the conductivity for hard water within 23 to 66 μs/cm after 6 hours of the assay.

  8. Freestanding bacterial cellulose-graphene oxide composite membranes with high mechanical strength for selective ion permeation

    PubMed Central

    Fang, Qile; Zhou, Xufeng; Deng, Wei; Zheng, Zhi; Liu, Zhaoping

    2016-01-01

    Graphene oxide (GO) based membranes have been widely applied in molecular separation based on the size exclusion effect of the nanochannels formed by stacked GO sheets. However, it’s still a challenge to prepare a freestanding GO-based membrane with high mechanical strength and structural stability which is prerequisite for separation application in aqueous solution. Here, a freestanding composite membrane based on bacterial cellulose (BC) and GO is designed and prepared. BC network provides a porous skeleton to spread GO sheets and uniformly incorporates into the GO layers, which endows the BC + GO composite membrane with well water-stability, excellent tensile strength, as well as improved toughness, guaranteeing its separation applicability in water environment. The resulting BC + GO membrane exhibits obviously discrepant permeation properties for different inorganic/organic ions with different size, and in particular, it can quickly separate ions in nano-scale from angstrom-scale. Therefore, this novel composite membrane is considered to be a promising candidate in the applications of water purification, food industry, biomedicine, and pharmaceutical and fuel separation. PMID:27615451

  9. Freestanding bacterial cellulose-graphene oxide composite membranes with high mechanical strength for selective ion permeation

    NASA Astrophysics Data System (ADS)

    Fang, Qile; Zhou, Xufeng; Deng, Wei; Zheng, Zhi; Liu, Zhaoping

    2016-09-01

    Graphene oxide (GO) based membranes have been widely applied in molecular separation based on the size exclusion effect of the nanochannels formed by stacked GO sheets. However, it’s still a challenge to prepare a freestanding GO-based membrane with high mechanical strength and structural stability which is prerequisite for separation application in aqueous solution. Here, a freestanding composite membrane based on bacterial cellulose (BC) and GO is designed and prepared. BC network provides a porous skeleton to spread GO sheets and uniformly incorporates into the GO layers, which endows the BC + GO composite membrane with well water-stability, excellent tensile strength, as well as improved toughness, guaranteeing its separation applicability in water environment. The resulting BC + GO membrane exhibits obviously discrepant permeation properties for different inorganic/organic ions with different size, and in particular, it can quickly separate ions in nano-scale from angstrom-scale. Therefore, this novel composite membrane is considered to be a promising candidate in the applications of water purification, food industry, biomedicine, and pharmaceutical and fuel separation.

  10. Highly carbonylated cellulose nanofibrous membranes utilizing maleic anhydride grafting for efficient lysozyme adsorption.

    PubMed

    Ma, Juncheng; Wang, Xueqin; Fu, Qiuxia; Si, Yang; Yu, Jianyong; Ding, Bin

    2015-07-22

    Construction of adsorptive materials for simple, efficient, and high-throughput adsorption of proteins is critical to meet the great demands of highly purified proteins in biotechnological and biopharmaceutical industry; however, it has proven extremely challenging. Here, we report a cost-effective strategy to create carbonyl groups surface-functionalized nanofibrous membranes under mild conditions for positively charged protein adsorption. Our approach allows maleic anhydride to in situ graft on cellulose nanofibrous membranes (CMA) to construct adsorptive membranes with large surface area and tortuous porous structure. Thereby, the resultant CMA membranes exhibited high adsorption capacity of 160 mg g(-1), fast equilibrium within 12 h, and good reversibility to lysozyme. Moreover, the dynamic adsorption was performed under low pressure-drops (750 Pa), with a relatively high saturation adsorption amount of 118 mg g(-1), which matched well with the requirements for proteins purification. Considering the excellent adsorption performance of the as-prepared adsorptive membranes, this simple and intriguing approach may pave a way for the design and development of robust and cost-effective adsorption membranes to meet the great demands for fast and efficient adsorption of positively charged proteins.

  11. The Use of Cellulose Membrane to Eliminate Burst Release from Intravaginal Rings.

    PubMed

    Helbling, Ignacio M; Ibarra, Juan C D; Luna, Julio A

    2016-07-01

    Burst release was observed when ethylene vinyl acetate copolymer (EVA) intravaginal rings were tested for progesterone release in our previous work (Helbling et al. Pharm Res. 31(3):795-808, 2014). Burst release is undesirable in controlled delivery devices because release is uncontrollable and higher levels of active pharmaceutical ingredient could lead to the occurrence of adverse effect. The present contribution is about the use of membranes to coat EVA rings to eliminate burst release. Physicochemical state of progesterone in uncoated rings and the solubility and diffusion coefficient in membrane were studied. Hormone delivery from several rings of different sizes was compared. A mathematical model was used to analyze the effects of membrane properties on delivery rate. No chemical interactions were detected between hormone and polymer. Hormone was mainly forming amorphous aggregates inside rings, and migration to membrane was not observed during storage. Diffusion coefficient was smaller in membrane (∼10(-8) cm(2) s(-1)) than in matrix (∼10(-7) cm(2) s(-1)). Zero-order release kinetics were obtained for coated rings, and release rate decreases as the thickness of the coat increases. Cellulose membrane successfully eliminates burst release and controls the delivery from EVA rings. The equations developed can be used to determine the appropriate coat thickness to produce specific release rate.

  12. Asymmetric composite membranes from chitosan and tricalcium phosphate useful for guided bone regeneration.

    PubMed

    Tai, Hung-Yin; Chou, Shiu-Huey; Cheng, Liao-Ping; Yu, Hung-Te; Don, Trong-Ming

    2012-01-01

    To fulfill the properties of barrier membranes useful for guided bone tissue regeneration in the treatment of periodontitis, in this study a simple process combining lyophilization with preheating treatment to produce asymmetric barrier membranes from biodegradable chitosan (CS) and functional β-tricalcium phosphate (TCP) was proposed. By preheating TCP/CS (3:10, w/w) in an acetic acid solution at 40°C, a skin layer that could greatly increase the mechanical properties of the membrane was formed. The asymmetric membrane with a skin layer had a modulus value almost 4-times that of the symmetric porous membrane produced only by lyophilization. This is beneficial for maintaining a secluded space for the bone regeneration, as well as to prevent the invasion of other tissues. The subsequent lyophilization at -20°C then gave the rest of material an interconnected pore structure with high porosity (83.9-90.6%) and suitable pore size (50-150 μm) which could promote the permeability and adhesiveness to bone cells, as demonstrated by the in vitro cell-culture of hFOB1.19 osteoblasts. Furthermore, the TCP particles added to CS could further increase the rigidity and the cell attachment and proliferation of hFOB1.19. The TCP/CS asymmetric composite membrane thus has the potential to be used as the barrier membrane for guided bone regeneration.

  13. Biological efficacy of silk fibroin nanofiber membranes for guided bone regeneration.

    PubMed

    Kim, Kyoung-Hwa; Jeong, Lim; Park, Ho-Nam; Shin, Seung-Yun; Park, Won-Ho; Lee, Sang-Chul; Kim, Tae-Il; Park, Yoon-Jeong; Seol, Yang-Jo; Lee, Yong-Moo; Ku, Young; Rhyu, In-Chul; Han, Soo-Boo; Chung, Chong-Pyoung

    2005-11-21

    The favorable biological properties of silk fibroin (SF) nanofiber membrane make it a good candidate for clinical applications as a device in bone and periodontal regenerative therapy. The purpose of this study is to evaluate the biocompatibility of the SF nanofiber membrane, and to examine its effect on bone regeneration in a rabbit calvarial model. To examine the biocompatibility of the electrospun SF membrane, we investigated cell proliferation, morphology, and differentiation. The bone regenerative efficacy of the membrane was evaluated in the calvarial defect of rabbits. The cell numbers and osteocalcin production labels were significantly increased in accordance with culture period. Cells had a stellate shape and broad cytoplasmic extensions on the membrane. The cells showed activity of ALPase that was comparable to culture dishes, and were calcified similarly to culture dishes. In in vivo tests, a complete bony union across the defects was observed after 8 weeks. At 12 weeks, the defect had completely healed with new bone. In conclusion, the SF nanofiber membrane was shown to possess good biocompatibility with enhanced bone regeneration and no evidence of any inflammatory reaction. These results strongly suggest that the SF membrane should be useful as a tool for guided bone regeneration.

  14. Low cost hydrogen/novel membrane technology for hydrogen separation from synthesis gas, Phase 1. [Polyetherimide, cellulose acetate and ethylcellulose

    SciTech Connect

    Not Available

    1986-01-01

    The goal of this program is to develop polymer membranes useful in the preparation of hydrogen from coal-derived synthesis gas. During this quarter the first experiment were aimed at developing high performance composite membranes for the separation of hydrogen from nitrogen and carbon monoxide. Three polymers have been selected as materials for these membranes: polyetherimide cellulose acetate and ethylcellulose. This quarter the investigators worked on polyetherimide and cellulose acetate membranes. The overall structure of these membranes is shown schematically in Figure 1. As shown, a microporous support membrane is first coated with a high flux intermediate layer then with an ultrathin permselective layer and finally, if necessary, a thin protective high flux layer. 1 fig., 4 tabs.

  15. Reverse osmosis transport of alkali halides and nickel salts through cellulose triacetate membranes. Performance prediction from NaCl experiments

    SciTech Connect

    Nirmal, J.D.; Pandya, V.P.; Desai, N.V.; Rangarajan, R. )

    1992-10-01

    The separation of alkali metal halides, nickel chloride, and nickel sulfate was determined for cellulose triacetate reverse osmosis (CTA RO) membranes. From transport analysis, the relative free energy parameters for transport of these salts through CTA membranes were determined. From these relative free energy parameters of salts, the solute separation by CTA membranes could be predicted from RO experiment with NaCl solution. The transport analysis and an illustration of how the concept is useful are presented in this paper.

  16. Guided bone regeneration is promoted by the molecular events in the membrane compartment.

    PubMed

    Turri, Alberto; Elgali, Ibrahim; Vazirisani, Forugh; Johansson, Anna; Emanuelsson, Lena; Dahlin, Christer; Thomsen, Peter; Omar, Omar

    2016-04-01

    The working hypothesis of guided bone regeneration (GBR) is that the membrane physically excludes non-osteogenic tissues from interfering with bone healing. However, the underlying mechanisms are insufficiently explained. This study aimed to investigate the molecular and structural pattern of bone healing in trabecular bone defects, with and without naturally derived resorbable membrane. Defects were created in rat femurs and treated with the membrane or left empty (sham). After 3d, 6d and 28d, the defect sites and membranes were harvested and analyzed with histology, histomorphometry, quantitative-polymerase chain reaction (qPCR), Western blot (WB) and immunohistochemistry (IHC). Histomorphometry demonstrated that the presence of the membrane promoted bone formation in early and late periods. This was in parallel with upregulation of cell recruitment and coupled bone remodeling genes in the defect. Cells recruited into the membrane expressed signals for bone regeneration (BMP-2, FGF-2, TGF-β1 and VEGF). Whereas the native membrane contained FGF-2 but not BMP-2, an accumulation of FGF-2 and BMP-2 proteins and immunoreactive cells were demonstrated by WB and IHC in the in vivo implanted membrane. The results provide cellular and molecular evidence suggesting a novel role for the membrane during GBR, by acting as a bioactive compartment rather than a passive barrier.

  17. Mineralization and bone regeneration using a bioactive elastin-like recombinamer membrane.

    PubMed

    Tejeda-Montes, Esther; Klymov, Alexey; Nejadnik, M Reza; Alonso, Matilde; Rodriguez-Cabello, J Carlos; Walboomers, X Frank; Mata, Alvaro

    2014-09-01

    The search for alternative therapies to improve bone regeneration continues to be a major challenge for the medical community. Here we report on the enhanced mineralization, osteogenesis, and in vivo bone regeneration properties of a bioactive elastin-like recombinamer (ELR) membrane. Three bioactive ELRs exhibiting epitopes designed to promote mesenchymal stem cell adhesion (RGDS), mineralization (DDDEEKFLRRIGRFG), and both cell adhesion and mineralization were synthesized using standard recombinant protein techniques. The ELR materials were then used to fabricate membranes comprising either a smooth surface (Smooth) or channel microtopographies (Channels). Mineralization and osteoblastic differentiation of primary rat mesenchymal stem cells (rMSCs) were analyzed in both static and dynamic (uniaxial strain of 8% at 1 Hz frequency) conditions. Smooth mineralization membranes in static condition exhibited the highest quantity of calcium phosphate (Ca/P of 1.78) deposition with and without the presence of cells, the highest Young's modulus, and the highest production of alkaline phosphatase on day 10 in the presence of cells growing in non-osteogenic differentiation medium. These membranes were tested in a 5 mm-diameter critical-size rat calvarial defect model and analyzed for bone formation on day 36 after implantation. Animals treated with the mineralization membranes exhibited the highest bone volume within the defect as measured by micro-computed tomography and histology with no significant increase in inflammation. This study demonstrates the possibility of using bioactive ELR membranes for bone regeneration applications.

  18. Biodegradable effect of PLGA membrane in alveolar bone regeneration on beagle dog.

    PubMed

    Hua, Nan; Ti, Vivian Lao; Xu, Yuanzhi

    2014-11-01

    Guided bone regeneration (GBR) is a principle adopted from guided tissue regeneration (GTR). Wherein, GBR is used for the healing of peri-implant bony dehiscences, for the immediate placement of implants into extraction sockets and for the augmentation of atrophic alveolar ridges. This procedure is done by the placement of a resorbable or non-resorbable membrane that will exclude undesirable types of tissue growth between the extraction socket and the soft tissue to allow only bone cells to regenerate in the surgically treated lesion. Here, we investigated the biodegradable effect of polylactic-co-glycolic acid (PLGA) membrane in the alveolar bone on Beagle dogs. Results show that both collagen and PLGA membrane had been fully resorbed, biodegraded, at four weeks post-operative reentry into the alveolar bone. Histological results under light microscopy revealed formation of new bone trabeculae in the extraction sites on both collagen and PLGA membrane. In conclusion, PLGA membrane could be a potential biomaterials for use on GBR and GTR. Nevertheless, further studies will be necessary to elucidate the efficiency and cost effectiveness of PLGA as GBR membrane in clinical.

  19. Pervaporation of water and ethanol using a cellulose acetate butyrate membrane

    SciTech Connect

    Wu, W.S.; Lau, W.W.Y.; Rangaiah, G.P.; Sourirajan, S. . Dept. of Chemical Engineering)

    1993-10-15

    Okada and Matsuura's transport equations for pervaporation give rise to three fundamental parameters, namely, interfacial saturation vapor pressure P*, liquid transport parameter A/[delta], and vapor transport parameter B/[delta]. The effects of the chemical nature of the membrane material and the upstream operating pressures of 101.3 and 303.9 kPa on the above parameters were investigated from the pervaporation data at laboratory temperature (24 C) for water and ethanol using a cellulose acetate butyrate membrane. The results show that the P. values are essentially unaffected by the upstream pressure, and that they are generally higher than the literature values of saturation vapor pressure at 24 C. Further, the values for A/[delta] and B/[delta] tend to increase with increased upstream pressure for both systems studied. These results are discussed.

  20. Adsorptive removal of phenolic compounds using cellulose acetate phthalate-alumina nanoparticle mixed matrix membrane.

    PubMed

    Mukherjee, Raka; De, Sirshendu

    2014-01-30

    Mixed matrix membranes (MMMs) were prepared using alumina nanoparticles and cellulose acetate phthalate (CAP) by varying concentration of nanoparticles in the range of 10 to 25wt%. The membranes were characterized by scanning electron micrograph, porosity, permeability, molecular weight cut off, contact angle, surface zeta potential, mechanical strength. Addition of nanoparticles increased the porosity, permeability of the membrane up to 20wt% of alumina. pH at point of zero charge of the membrane was 5.4. Zeta potential of the membrane became more negative up to 20wt% of nanoparticles. Adsorption of phenolic derivatives, catechol, paranitrophenol, phenol, orthochloro phenol, metanitrophenol, by MMMs were investigated. Variation of rejection and permeate flux profiles were studied for different solutes as a function of various operating conditions, namely, solution pH, solute concentration in feed and transmembrane pressure drop. Difference in rejection of phenolic derivatives is consequence of interplay of surface charge and adsorption by alumina. Adsorption isotherm was fitted for different solutes and effects of pH were investigated. Catechol showed the maximum rejection 91% at solution pH 9. Addition of electrolyte reduced the rejection of solutes. Transmembrane pressure drop has insignificant effects on solute rejection. Competitive adsorption reduced the rejection of individual solute.

  1. Fibroblast attachment onto novel titanium mesh membranes for guided bone regeneration.

    PubMed

    Rakhmatia, Yunia Dwi; Ayukawa, Yasunori; Atsuta, Ikiru; Furuhashi, Akihiro; Koyano, Kiyoshi

    2015-05-01

    Titanium mesh is used in orthopedic surgery as a barrier membrane, as it offers suitable characteristics, which allow mechanical support during the formation of new bone. An ideal membrane would facilitate cell attachment onto its surface, thereby helping to stabilize the blood clot and integrate the membrane into the tissue. However, currently available titanium mesh has millimeter-level pore sizes, which lead to soft tissue ingrowth through the pores. Therefore, the aim of this study was to investigate the fibroblast attachment and migration on different designs of novel titanium mesh with micrometer pore size for guided bone regeneration treatment. Six types of novel titanium mesh membrane and three groups of commercially available membranes were used in this study. Fibroblasts were isolated from 4-day-old green fluorescence protein rats and seeded onto membrane surfaces. At 24 h, the cells attached to the membrane surfaces were fixed and stained with DAPI. The blue-stained nuclei on membrane surfaces, and both upper and lower sides were counted. It was shown that different membrane materials, structure and design differ considerably in their capacity for cell attachment to the membrane surface. The novel membranes, especially mesh with 12 pores compared with mesh with multi-pores, allowed the fibroblast attachment on the membrane surface, but hindered the fibroblast migration through the pores into the lower side of the membrane, which is associated with the defect area in the clinical condition.

  2. Sciatic nerve regeneration using a nerve growth factor-containing fibrin glue membrane.

    PubMed

    Ma, Shengzhong; Peng, Changliang; Wu, Shiqing; Wu, Dongjin; Gao, Chunzheng

    2013-12-25

    Our previous findings confirmed that the nerve growth factor-containing fibrin glue membrane provides a good microenvironment for peripheral nerve regeneration; however, the precise mechanism remains unclear. p75 neurotrophin receptor (p75(NTR)) plays an important role in the regulation of peripheral nerve regeneration. We hypothesized that a nerve growth factor-containing fibrin glue membrane can promote neural regeneration by up-regulating p75(NTR) expression. In this study, we used a silicon nerve conduit to bridge a 15 mm-long sciatic nerve defect and injected a mixture of nerve growth factor and fibrin glue at the anastomotic site of the nerve conduit and the sciatic nerve. Through RT-PCR and western blot analysis, nerve growth factor-containing fibrin glue membrane significantly increased p75(NTR) mRNA and protein expression in the Schwann cells at the anastomotic site, in particular at 8 weeks after injection of the nerve growth factor/fibrin glue mixture. These results indicate that nerve growth factor-containing fibrin glue membrane can promote peripheral nerve regeneration by up-regulating p75(NTR) expression in Schwann cells.

  3. A simple route to develop transparent doxorubicin-loaded nanodiamonds/cellulose nanocomposite membranes as potential wound dressings.

    PubMed

    Luo, Xiaogang; Zhang, Hao; Cao, Zhenni; Cai, Ning; Xue, Yanan; Yu, Faquan

    2016-06-05

    The objective of this study is to develop transparent porous nanodiamonds/cellulose nanocomposite membranes with controlled release of doxorubicin for potential applications as wound dressings, which were fabricated by tape casting method from dispersing carboxylated nanodiamonds and dissolving cellulose homogeneously in 7 wt% NaOH/12 wt% urea aqueous solution. By adjusting the carboxylated nanodiamonds content, various nanocomposite membranes were obtained. The structure and properties of these membranes have been investigated by light transmittance measurements, scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), differential scanning calorimetry (DSC), tensile tests, water loss analyses, etc. The drug loading and release was investigated using doxorubicin hydrochloride as a model drug. In vitro cytotoxicity assay of the membranes was also studied. This work presented a proof-of-concept utility of these membranes for loading and release of bioactive compounds to be employed as a candidate for wound dressing.

  4. Dephosphorylation during Bleach and Regeneration of Visual Pigment in Carp Rod and Cone Membranes*

    PubMed Central

    Yamaoka, Hiromi; Tachibanaki, Shuji; Kawamura, Satoru

    2015-01-01

    On absorption of light by vertebrate visual pigment, the chromophore, 11-cis retinal, is isomerized to all-trans retinal to activate the phototransduction cascade, which leads to a hyperpolarizing light response. Activated pigment is inactivated by phosphorylation on the protein moiety, opsin. Isomerized all-trans retinal is ultimately released from opsin, and the pigment is regenerated by binding to 11-cis retinal. In this pigment regeneration cycle, the phosphates incorporated should be removed in order that the pigment regains the capability of activating the phototransduction cascade. However, it is not clear yet how pigment dephosphorylation takes place in the regeneration cycle. First in this study, we tried to estimate the dephosphorylation activity in living carp rods and cones and found that the activity, which is present mainly in the cytoplasm in both rods and cones, is three times higher in cones than in rods. Second, we examined at which stage the dephosphorylation takes place; before or after the release of all-trans retinal, during pigment regeneration, or after pigment regeneration. For this purpose we prepared three types of phosphorylated substrates in purified carp rod and cone membranes: phosphorylated bleaching intermediate, phosphorylated opsin, and phosphorylated and regenerated pigment. We also examined the effect of pigment regeneration on the dephosphorylation. The results showed that the dephosphorylation does not show substrate preference in the regeneration cycle and suggested that the dephosphorylation takes place constantly. The results also suggest that, under bright light, some of the regenerated visual pigment remains phosphorylated to reduce the light sensitivity in cones. PMID:26286749

  5. Dephosphorylation during bleach and regeneration of visual pigment in carp rod and cone membranes.

    PubMed

    Yamaoka, Hiromi; Tachibanaki, Shuji; Kawamura, Satoru

    2015-10-02

    On absorption of light by vertebrate visual pigment, the chromophore, 11-cis retinal, is isomerized to all-trans retinal to activate the phototransduction cascade, which leads to a hyperpolarizing light response. Activated pigment is inactivated by phosphorylation on the protein moiety, opsin. Isomerized all-trans retinal is ultimately released from opsin, and the pigment is regenerated by binding to 11-cis retinal. In this pigment regeneration cycle, the phosphates incorporated should be removed in order that the pigment regains the capability of activating the phototransduction cascade. However, it is not clear yet how pigment dephosphorylation takes place in the regeneration cycle. First in this study, we tried to estimate the dephosphorylation activity in living carp rods and cones and found that the activity, which is present mainly in the cytoplasm in both rods and cones, is three times higher in cones than in rods. Second, we examined at which stage the dephosphorylation takes place; before or after the release of all-trans retinal, during pigment regeneration, or after pigment regeneration. For this purpose we prepared three types of phosphorylated substrates in purified carp rod and cone membranes: phosphorylated bleaching intermediate, phosphorylated opsin, and phosphorylated and regenerated pigment. We also examined the effect of pigment regeneration on the dephosphorylation. The results showed that the dephosphorylation does not show substrate preference in the regeneration cycle and suggested that the dephosphorylation takes place constantly. The results also suggest that, under bright light, some of the regenerated visual pigment remains phosphorylated to reduce the light sensitivity in cones.

  6. Comparison of biofouling mechanisms between cellulose triacetate (CTA) and thin-film composite (TFC) polyamide forward osmosis membranes in osmotic membrane bioreactors.

    PubMed

    Wang, Xinhua; Zhao, Yanxiao; Yuan, Bo; Wang, Zhiwei; Li, Xiufen; Ren, Yueping

    2016-02-01

    There are two types of popular forward osmosis (FO) membrane materials applied for researches on FO process, cellulose triacetate (CTA) and thin film composite (TFC) polyamide. However, performance and fouling mechanisms of commercial TFC FO membrane in osmotic membrane bioreactors (OMBRs) are still unknown. In current study, its biofouling behaviors in OMBRs were investigated and further compared to the CTA FO membrane. The results indicated that β-D-glucopyranose polysaccharides and microorganisms accounted for approximately 77% of total biovolume on the CTA FO membrane while β-D-glucopyranose polysaccharides (biovolume ratio of 81.1%) were the only dominant biofoulants on the TFC FO membrane. The analyses on the biofouling structure implied that a tighter biofouling layer with a larger biovolume was formed on the CTA FO membrane. The differences in biofouling behaviors including biofoulants composition and biofouling structure between CTA and TFC FO membranes were attributed to different membrane surface properties.

  7. Is the poly (L- lactide- co- caprolactone) nanofibrous membrane suitable for urinary bladder regeneration?

    PubMed

    Pokrywczynska, Marta; Jundzill, Arkadiusz; Adamowicz, Jan; Kowalczyk, Tomasz; Warda, Karolina; Rasmus, Marta; Buchholz, Lukasz; Krzyzanowska, Sandra; Nakielski, Pawel; Chmielewski, Tomasz; Bodnar, Magdalena; Marszalek, Andrzej; Debski, Robert; Frontczak-Baniewicz, Malgorzata; Mikułowski, Grzegorz; Nowacki, Maciej; Kowalewski, Tomasz A; Drewa, Tomasz

    2014-01-01

    The purpose of this study was to compare: a new five-layered poly (L-lactide-co-caprolactone) (PLC) membrane and small intestinal submucosa (SIS) as a control in rat urinary bladder wall regeneration. The five-layered poly (L-lactide-co-caprolactone) membrane was prepared by an electrospinning process. Adipose tissue was harvested from five 8-week old male Wistar rats. Adipose derived stem cells (ADSCs) were seeded in a density of 3×10(6) cells/cm2 onto PLC membrane and SIS scaffolds, and cultured for 5-7 days in the stem cell culture medium. Twenty male Wistar rats were randomly divided into five equal groups. Augmentation cystoplasty was performed in a previously created dome defect. Groups: (I) PLC+ 3×10(6)ADSCs; (II) SIS+ 3×10(6)ADSCs; (III) PLC; (IV) SIS; (V) control. Cystography was performed after three months. The reconstructed urinary bladders were evaluated in H&E and Masson's trichrome staining. Regeneration of all components of the normal urinary bladder wall was observed in bladders augmented with cell-seeded SIS matrices. The urinary bladders augmented with SIS matrices without cells showed fibrosis and graft contraction. Bladder augmentation with the PLC membrane led to numerous undesirable events including: bladder wall perforation, fistula or diverticula formation, and incorporation of the reconstructed wall into the bladder lumen. The new five-layered poly (L-lactide-co-caprolactone) membrane possesses poorer potential for regenerating the urinary bladder wall compared with SIS scaffold.

  8. Is the Poly (L- Lactide- Co– Caprolactone) Nanofibrous Membrane Suitable for Urinary Bladder Regeneration?

    PubMed Central

    Kowalczyk, Tomasz; Warda, Karolina; Rasmus, Marta; Buchholz, Lukasz; Krzyzanowska, Sandra; Nakielski, Pawel; Chmielewski, Tomasz; Bodnar, Magdalena; Marszalek, Andrzej; Debski, Robert; Frontczak-Baniewicz, Malgorzata; Mikułowski, Grzegorz; Nowacki, Maciej; Kowalewski, Tomasz A.; Drewa, Tomasz

    2014-01-01

    The purpose of this study was to compare: a new five-layered poly (L–lactide–co–caprolactone) (PLC) membrane and small intestinal submucosa (SIS) as a control in rat urinary bladder wall regeneration. The five-layered poly (L–lactide–co–caprolactone) membrane was prepared by an electrospinning process. Adipose tissue was harvested from five 8-week old male Wistar rats. Adipose derived stem cells (ADSCs) were seeded in a density of 3×106 cells/cm2 onto PLC membrane and SIS scaffolds, and cultured for 5-7 days in the stem cell culture medium. Twenty male Wistar rats were randomly divided into five equal groups. Augmentation cystoplasty was performed in a previously created dome defect. Groups: (I) PLC+ 3×106ADSCs; (II) SIS+ 3×106ADSCs; (III) PLC; (IV) SIS; (V) control. Cystography was performed after three months. The reconstructed urinary bladders were evaluated in H&E and Masson's trichrome staining. Regeneration of all components of the normal urinary bladder wall was observed in bladders augmented with cell-seeded SIS matrices. The urinary bladders augmented with SIS matrices without cells showed fibrosis and graft contraction. Bladder augmentation with the PLC membrane led to numerous undesirable events including: bladder wall perforation, fistula or diverticula formation, and incorporation of the reconstructed wall into the bladder lumen. The new five-layered poly (L–lactide–co–caprolactone) membrane possesses poorer potential for regenerating the urinary bladder wall compared with SIS scaffold. PMID:25162451

  9. In vitro evaluation of electrospun chitosan mats crosslinked with genipin as guided tissue regeneration barrier membranes

    NASA Astrophysics Data System (ADS)

    Norowski, Peter Andrew, Jr.

    Guided tissue regeneration (GTR) is a surgical technique commonly used to exclude bacteria and soft tissues from bone graft sites in oral/maxillofacial bone graft sites by using a barrier membrane to maintain the graft contour and space. Current clinical barrier membrane materials based on expanded polytetrafluoroethylene (ePTFE) and bovine type 1 collagen are non-ideal and experience a number of disadvantages including membrane exposure, bacterial colonization/biofilm formation and premature degradation, all of which result in increased surgical intervention and poor bone regeneration. These materials do not actively participate in tissue regeneration, however bioactive materials, such as chitosan, may provide advantages such as the ability to stimulate wound healing and de novo bone formation. Our hypothesis is that electrospun chitosan GTR membranes will support cell attachment and growth but prevent cell infiltration/penetration of membrane, demonstrate in vitro degradation predictive of 4--6 month in vivo functionality, and will deliver antibiotics locally to prevent/inhibit periopathogenic complications. To test this hypothesis a series of chitosan membranes were electrospun, in the presence or absence of genipin, a natural crosslinking agent, at concentrations of 5 and 10 mM. These membranes were characterized by scanning electron microscopy, tensile testing, suture pullout testing, Fourier transform infrared spectroscopy, X-ray diffraction, and gel permeation chromatography, and in vitro biodegradation for diameter/morphology of fibers, membrane strengths, degree of crosslinking, crystallinity, molecular weight, and degradation kinetics, respectively. Cytocompability of membranes was evaluated in osteoblastic, fibroblastic and monocyte cultures. The activity of minocycline loaded and released from the membranes was determined in zone of inhibition tests using P. gingivalis microbe. The results demonstrated that genipin crosslinking extended the in vitro

  10. [Construction of guided bone regeneration membrane by tissue engineering in vitro].

    PubMed

    Huang, Lanfeng; Qi, Xin; Liu, Jianguo; Xu, Xinxiang

    2004-08-01

    In this study, porous polymer (PLA/PCL) membrane was first treated with ethanol to become hydrophilic, and then immersed into DMEM with 50% fetal bovine serum to enhance the affinity to cells. MSCs cultured in osteogenic medium were loaded into the membrane at density of 5 x 10(6)/cm2 for 7 days, and scanning electrical microscope was used to observe the growth of the MSCs. The growth of MSCs inside the constructs was functionally well, and the cells proliferated with the time of culture. We concluded from current study that the membrane had satisfactory biocompatibility and the constructs could be used to guided bone regeneration.

  11. Electrodialysis with bipolar membrane for regeneration of a spent activated carbon.

    PubMed

    Drouiche, N; Grib, H; Abdi, N; Lounici, H; Pauss, A; Mameri, N

    2009-10-15

    The main purpose of the present work was to develop a treatment method to regenerate granular adsorbent beds saturated with H(2)S by utilizing three electrodialysis compartments equipped with a cation or an anion exchange membrane or a bipolar membrane. Three electrodialysis compartments were utilized under various experimental parameters to determine the optimum conditions for the recovery of column particles saturated by H(2)S. The desulphurization operation is achieved with the extent of extraction close to 90% and an electric current density of about 30%. Use of the bipolar membrane makes it possible to regenerate the saturated adsorbent granules without adding chemical products. Since the only reagent was electricity, the projected economics are very attractive.

  12. Guided tissue regeneration-based root coverage utilizing collagen membranes: technique and case reports.

    PubMed

    Wang, Hom-Lay; Al-Shammari, Khalaf F

    2002-01-01

    Gingival recession defects have traditionally been treated with various grafting procedures. Recently, guided tissue regeneration with collagen membranes has shown promising results. This article reviews the rationale, indications, contraindications, and clinical methods for the use of bioabsorbable collagen membrane barriers. Several properties make collagen membranes attractive candidates for use as barriers in guided tissue regeneration-based root coverage procedures. These include the inhibition of epithelial migration and promotion of new connective tissue attachment; the ability to aggregate platelets, thereby facilitating wound stabilization and maturation; the promotion of cellular migration and wound closure; the elimination of the need for reentry surgery; and the ability to augment tissue thickness. Cases are presented to illustrate the surgical principles and techniques.

  13. An Outer Membrane Protein Involved in the Uptake of Glucose Is Essential for Cytophaga hutchinsonii Cellulose Utilization

    PubMed Central

    Zhou, Hong; Wang, Xia; Yang, Tengteng; Zhang, Weixin; Chen, Guanjun

    2016-01-01

    Cytophaga hutchinsonii specializes in cellulose digestion by employing a collection of novel cell-associated proteins. Here, we identified a novel gene locus, CHU_1276, that is essential for C. hutchinsonii cellulose utilization. Disruption of CHU_1276 in C. hutchinsonii resulted in complete deficiency in cellulose degradation, as well as compromised assimilation of cellobiose or glucose at a low concentration. Further analysis showed that CHU_1276 was an outer membrane protein that could be induced by cellulose and low concentrations of glucose. Transcriptional profiling revealed that CHU_1276 exerted a profound effect on the genome-wide response to both glucose and Avicel and that the mutant lacking CHU_1276 displayed expression profiles very different from those of the wild-type strain under different culture conditions. Specifically, comparison of their transcriptional responses to cellulose led to the identification of a gene set potentially regulated by CHU_1276. These results suggest that CHU_1276 plays an essential role in cellulose utilization, probably by coordinating the extracellular hydrolysis of cellulose substrate with the intracellular uptake of the hydrolysis product in C. hutchinsonii. PMID:26773084

  14. High-Strength Composite Fibers from Cellulose-Lignin Blends Regenerated from Ionic Liquid Solution.

    PubMed

    Ma, Yibo; Asaadi, Shirin; Johansson, Leena-Sisko; Ahvenainen, Patrik; Reza, Mehedi; Alekhina, Marina; Rautkari, Lauri; Michud, Anne; Hauru, Lauri; Hummel, Michael; Sixta, Herbert

    2015-12-07

    Composite fibres that contain cellulose and lignin were produced from ionic liquid solutions by dry-jet wet spinning. Eucalyptus dissolving pulp and organosolv/kraft lignin blends in different ratios were dissolved in the ionic liquid 1,5-diazabicyclo[4.3.0]non-5-enium acetate to prepare a spinning dope from which composite fibres were spun successfully. The composite fibres had a high strength with slightly decreasing values for fibres with an increasing share of lignin, which is because of the reduction in crystallinity. The total orientation of composite fibres and SEM images show morphological changes caused by the presence of lignin. The hydrophobic contribution of lignin reduced the vapour adsorption in the fibre. Thermogravimetric analysis curves of the composite fibres reveal the positive effect of the lignin on the carbonisation yield. Finally, the composite fibre was found to be a potential raw material for textile manufacturing and as a precursor for carbon fibre production.

  15. Correlation between type of alkali rinsing, cytotoxicity of bio-nanocellulose and presence of metabolites within cellulose membranes.

    PubMed

    Junka, Adam; Fijałkowski, Karol; Ząbek, Adam; Mikołajewicz, Katarzyna; Chodaczek, Grzegorz; Szymczyk, Patrycja; Smutnicka, Danuta; Żywicka, Anna; Sedghizadeh, Parish Paymon; Dziadas, Mariusz; Młynarz, Piotr; Bartoszewicz, Marzenna

    2017-02-10

    The study aimed at evaluation of various types of alkali rinsing with regard to their efficacy in terms of removal, not only of bacteria but also bacterial metabolites, from cellulose matrices formed by three Komagataeibacter xylinus strains. Moreover, we tested the type of alkali rinsing on membrane cytotoxicity in vitro in fibroblast and osteoblast cells and we compared matrices' ability to induce oxidative stress in macrophages. We identified 11 metabolites of bacterial origin that remained in cellulose after rinsing. Moreover, our results indicated that the type of alkali rinsing should be adjusted to specific K. xylinus strains that are used as cellulose producers to obtain safe biomaterials in the context of low cytotoxicity and macrophage induction. The findings have translational importance and may be of direct significance to cellulose dressing manufacturers.

  16. Electrospun PDLLA/PLGA composite membranes for potential application in guided tissue regeneration.

    PubMed

    Zhang, Ershuai; Zhu, Chuanshun; Yang, Jun; Sun, Hong; Zhang, Xiaomin; Li, Suhua; Wang, Yonglan; Sun, Lu; Yao, Fanglian

    2016-01-01

    With the aim to explore a membrane system with appropriate degradation rate and excellent cell-occlusiveness for guided tissue regeneration (GTR), a series of poly(D, L-lactic acid) (PDLLA)/poly(D, L-lactic-co-glycolic acid) (PLGA) (100/0, 70/30, 50/50, 30/70, 0/100, w/w) composite membranes were fabricated via electrospinning. The fabricated membranes were evaluated by morphological characterization, water contact angle measurement and tensile test. In vitro degradation was characterized in terms of the weight loss and the morphological change. Moreover, in vitro cytologic research revealed that PDLLA/PLGA composite membranes could efficiently inhibit the infiltration of 293 T cells. Finally, subcutaneous implant test on SD rat in vivo showed that PDLLA/PLGA (70/30, 50/50) composite membranes could function well as a physical barrier to prevent cellular infiltration within 13 weeks. These results suggested that electrospun PDLLA/PLGA (50/50) composite membranes could serve as a promising barrier membrane for guided tissue regeneration due to suitable biodegradability, preferable mechanical properties and excellent cellular shielding effects.

  17. Regenerated keratin membrane to match the in vitro drug diffusion through human epidermis

    PubMed Central

    Selmin, Francesca; Cilurzo, Francesco; Aluigi, Annalisa; Franzè, Silvia; Minghetti, Paola

    2012-01-01

    This work aimed to develop membranes made of regenerated keratin and ceramides (CERs) to match the barrier property of the human stratum corneum in in vitro percutaneous absorption studies. The membrane composition was optimized on the basis of the in vitro drug diffusion profiles of ibuprofen, propranolol and testosterone chosen as model drugs on the basis of their different diffusion and solubility properties. The data were compared to those obtained using human epidermis. The ATR-FTIR and SEM analyses revealed that CERs were suspended into the regenerated keratin matrix, even if a partial solubilization occurred. It resulted in the membranes being physically stable after exposure to aqueous buffer and/or mineral oil and the fluxes of ibuprofen and propranolol from these vehicles through membranes and human skin were of the same order of magnitude. The best relationship with human epidermis data was obtained with 180 μm-thick membrane containing 1% ceramide III and 1% ceramide VI. The data on the testosterone diffusion were affected by the exposure of the membrane to a water/ethanol solution over a prolonged period of time, indicating that such an organic solvent was able to modify the supermolecular organization of keratin and CERs. The keratin/CER membranes can represent a simplified model to assay the in vitro skin permeability study of small molecules. PMID:25755997

  18. Investigation of the pore structure and morphology of cellulose acetate membranes using small-angle neutron scattering. 2: Ultrafiltration and reverse-osmosis membranes

    SciTech Connect

    Kulkarni, S.; Krause, S. ); Wignall, G.D. . Solid State Div.)

    1994-11-07

    Pore structure in cellulose acetate ultrafiltration (UF) and reverse-osmosis (RO) membranes has been studied using small-angle neutron scattering. Scattering experiments were carried out on dry membranes as well as on membranes swollen with deuterated solvents (D[sub 2]O and CD[sub 3]OD). In addition, the RO membranes were studied both before and after annealing (a process of heating a membrane in a water bath at [approximately]75 C to improve its separation properties). The pore surface in UF membranes was found to be smooth and nonfractal, as evidenced by the fourth power law behavior at high Q. Values of average pore sizes obtained for dry and solvent swollen membranes agree well with pore sizes obtained by other methods. For cellulose acetate RO membranes in their dry state, the unannealed membrane appears to consist of two discrete pore size distributions in the intermediate and high Q region while the annealed membrane contains a much wider distribution of pore sizes. These results give a good account of the changes occurring in the structure of RO membranes as a result of annealing, and agree well with the prediction of other authors.

  19. The effects of urease immobilization on the transport characteristics and protein adsorption capacity of cellulose acetate based hemodialysis membranes.

    PubMed

    Mahlicli, Filiz Yasar; Altinkaya, Sacide Alsoy

    2009-10-01

    In this study, cellulose acetate (CA) based hemodialysis membranes were prepared by a dry phase inversion method and the influences of urease immobilization on the clearing performance and protein adsorption capacity of the membranes were investigated. Permeation experiments have shown that modification of CA membranes with urease immobilization not only enhanced the transport rate of urea but also increased the permeation coefficients of uric acid and creatinine by changing the structure of the membrane. Furthermore, the protein adsorption capacity of the CA membranes decreased. On the other hand, the mechanical strength of the modified CA membrane did not change significantly compared with that of the unmodified one. A mathematical model was derived to determine the rate of mass transfer of urea through modified CA membranes. Model predictions along with the experimental data suggest that urease immobilization can be used as an alternative method in preparing CA based hemodialysis membranes with improved transport characteristics and biocompatibility through reduced protein adsorption capacities.

  20. Complexes of Magnetic Nanoparticles with Cellulose Nanocrystals as Regenerable, Highly Efficient, and Selective Platform for Protein Separation.

    PubMed

    Guo, Jiaqi; Filpponen, Ilari; Johansson, Leena-Sisko; Mohammadi, Pezhman; Latikka, Mika; Linder, Markus B; Ras, Robin H A; Rojas, Orlando J

    2017-03-13

    We present an efficient approach to develop cellulose nanocrystal (CNC) hybrids with magnetically responsive Fe3O4 nanoparticles that were synthesized using the (Fe(3+)/Fe(2+)) coprecipitation. After 2,2,6,6-tetramethylpiperidine-1-oxyl radical (TEMPO)-catalyzed oxidation of CNC, carbodiimide (EDC/NHS) was used for coupling amine-containing iron oxide nanoparticles that were achieved by dopamine ligand exchange (NH2-Fe3O4 NPs). The as-prepared hybrids (Fe3O4@CNC) were further complexed with Cu(II) ions to produce specific protein binding sites. The performance of magnetically responsive Cu-Fe3O4@CNC hybrids was assessed by selectively separating lysozyme from aqueous media. The hybrid system displayed a remarkable binding capacity with lysozyme of 860.6 ± 14.6 mg/g while near full protein recovery (∼98%) was achieved by simple elution. Moreover, the regeneration of Fe3O4@CNC hybrids and efficient reutilization for protein separation was demonstrated. Finally, lysozyme separation from matrices containing egg white was achieved, thus revealing the specificity and potential of the presented method.

  1. Preparation and properties of graphene oxide-regenerated cellulose/polyvinyl alcohol hydrogel with pH-sensitive behavior.

    PubMed

    Rui-Hong, Xie; Peng-Gang, Ren; Jian, Hui; Fang, Ren; Lian-Zhen, Ren; Zhen-Feng, Sun

    2016-03-15

    In this study, graphene oxide reinforced regenerated cellulose/polyvinyl alcohol (GO-RCE/PVA) ternary hydrogels were successfully prepared via a repeated freezing and thawing method in NaOH/urea aqueous solution. The effect of GO content on the mechanical properties, swelling behavior, water content of composite hydrogels was investigated. It was found that the mechanical properties of GO-RCE/PVA ternary hydrogels were largely enhanced relative to RCE/PVA hydrogels. With the addition of 1.0wt% GO, the tensile strength was increased by 40.4% from 0.52MPa to 0.73MPa, accompanied by the increase of the elongation at break (from 103% to 238%). Meanwhile, GO-RCE/PVA ternary hydrogels performed the excellent pH-sensitivity, and the higher pH leaded to higher swelling ratio. With 0.8wt% GO loading, the swelling ratio of GO-RCE/PVA ternary hydrogel was improved from 150% (pH=2) to 310% (pH=14). In addition, a slight increase in the water content of the ternary hydrogel was achieved with increasing concentrations of GO. It is believed that this novel ternary hydrogels is a promising material in the application of biomedical engineering and intelligent devices.

  2. Elastic properties of thin poly(vinyl alcohol)-cellulose nanocrystal membranes.

    PubMed

    Pakzad, A; Simonsen, J; Yassar, R S

    2012-02-01

    In spite of extensive studies on the preparation and characterization of nanocomposite materials, the correlation of their properties at the nanoscale with those in bulk is a relatively unexplored area. This is of great importance, especially for materials with potential biomedical applications, where surface properties are as important in determining their applicability as bulk characteristics. In this study, the nanomechanical characteristics of thin poly(vinyl alcohol) (PVOH)-poly(acrylic acid) (PAA)-cellulose nanocrystal (CNC) membranes were studied using the nanoindentation module in an atomic force microscope (AFM) and the properties were compared with the macro-scale properties obtained by tensile tests. In general, the elastic properties measured by nanoindentation followed the same trend as macro-scale tensile tests except for the PVOH 85-PAA 0-CNC 15 sample. In comparison to the macro-scale elastic properties, the measured elastic moduli with AFM were higher. Macro-scale tensile test results indicated that, in the presence of PAA, incorporation of CNCs up to 20 wt% improved the elastic modulus of PVOH, but when no PAA was added, increasing the CNC content above 10 wt% resulted in their agglomeration and degradation in mechanical properties of PVOH. The discrepancy between macro-scale tensile tests and nanoindentation in the PVOH 85-PAA 0-CNC 15 sample was correlated to the high degree of inhomogeneity of CNC dispersion in the matrix. It was found that the composites reinforced with cellulose nanocrystals had smaller indentation imprints and the pile-up effect increased with the increase of cellulose nanocrystal content.

  3. Optical, bactericidal and water repellent properties of electrospun nano-composite membranes of cellulose acetate and ZnO.

    PubMed

    Anitha, S; Brabu, B; John Thiruvadigal, D; Gopalakrishnan, C; Natarajan, T S

    2013-09-12

    In this report, ZnO nanoparticles embedded cellulose acetate (CA) fibrous membrane with multifunctional properties have been prepared through electrospinning method. The morphology of the electrospun composite membrane was analyzed by scanning electron microscope (SEM). It was found that the polymer concentration in the solution has a significant effect on the morphology of the fibers. The optical property of the sample was tested using photo luminescence (PL) spectra. There is no significant change in the emission features of cellulose acetate with the addition of ZnO. The anti-bacterial property of the sample was studied using disk diffusion method. The wettability of the pure and composite fibrous membrane was also studied by measuring the contact angle of water on the membrane. It was observed that the embedded ZnO in the CA was responsible for the hydrophobic nature of the surface.

  4. Effect of the Human Amniotic Membrane on Liver Regeneration in Rats

    PubMed Central

    Sipahi, Mesut; Şahin, Sevinç; Arslan, Ergin; Börekci, Hasan; Metin, Bayram; Cantürk, Nuh Zafer

    2015-01-01

    Introduction. Operations are performed for broader liver surgery indications for a better understanding of hepatic anatomy/physiology and developments in operation technology. Surgery can cure some patients with liver metastasis of some tumors. Nevertheless, postoperative liver failure is the most feared complication causing mortality in patients who have undergone excision of a large liver mass. The human amniotic membrane has regenerative effects. Thus, we investigated the effects of the human amniotic membrane on regeneration of the resected liver. Methods. Twenty female Wistar albino rats were divided into control and experimental groups and underwent a 70% hepatectomy. The human amniotic membrane was placed over the residual liver in the experimental group. Relative liver weight, histopathological features, and biochemical parameters were assessed on postoperative day 3. Results. Total protein and albumin levels were significantly lower in the experimental group than in the control group. No difference in relative liver weight was observed between the groups. Hepatocyte mitotic count was significantly higher in the experimental group than in the control group. Hepatic steatosis was detected in the experimental group. Conclusion. Applying the amniotic membrane to residual liver adversely affected liver regeneration. However, mesenchymal stem cell research has the potential to accelerate liver regeneration investigations. PMID:26457000

  5. In vitro synthesis of cellulose microfibrils by a membrane protein from protoplasts of the non-vascular plant Physcomitrella patens.

    PubMed

    Cho, Sung Hyun; Du, Juan; Sines, Ian; Poosarla, Venkata Giridhar; Vepachedu, Venkata; Kafle, Kabindra; Park, Yong Bum; Kim, Seong H; Kumar, Manish; Nixon, B Tracy

    2015-09-01

    Plant cellulose synthases (CesAs) form a family of membrane proteins that are associated with hexagonal structures in the plasma membrane called CesA complexes (CSCs). It has been difficult to purify plant CesA proteins for biochemical and structural studies. We describe CesA activity in a membrane protein preparation isolated from protoplasts of Physcomitrella patens overexpressing haemagglutinin (HA)-tagged PpCesA5. Incubating the membrane preparation with UDP-glucose predominantly produced cellulose. Negative-stain EM revealed microfibrils. Cellulase bound to and degraded these microfibrils. Vibrational sum frequency generation (SFG) spectroscopic analysis detected the presence of crystalline cellulose in the microfibrils. Putative CesA proteins were frequently observed attached to the microfibril ends. Combined cross-linking and gradient centrifugation showed bundles of cellulose microfibrils with larger particle aggregates, possibly CSCs. These results suggest that P. patens is a useful model system for biochemical and structural characterization of plant CSCs and their components.

  6. Rhodopsin in the rod surface membrane regenerates more rapidly than bulk rhodopsin in the disc membranes in vivo

    PubMed Central

    Kessler, Christopher; Tillman, Megan; Burns, Marie E; Pugh, Edward N

    2014-01-01

    Sustained vertebrate vision requires that opsin chromophores isomerized by light to the all-trans form be replaced with 11-cis retinal to regenerate the visual pigment. We have characterized the early receptor potential (ERP), a component of the electroretinogram arising from photoisomerization-induced charge displacements in plasma membrane visual pigment, and used it to measure pigment bleaching and regeneration in living mice. The mouse ERP was characterized by an outward ‘R2’ charge displacement with a time constant of 215 μs that discharged through a membrane with an apparent time constant of ∼0.6 ms. After complete bleaching of rhodopsin, the ERP recovered in two phases. The initial, faster phase had a time constant of ∼1 min, accounted for ∼20% of the total, and was not dependent on the level of expression of the retinal pigment epithelium isomerase, Rpe65. The slower, complementary phase had a time constant of 23 min in wild-type (WT) mice (C57Bl/6) and was substantially slowed in Rpe65+/− mice. Comparison of the ERPs of a mouse line expressing 150% of the normal level of cone M-opsin with those of WT mice revealed that M-opsin contributed 26% of the total WT ERP in these experiments, with the remaining 74% arising from rhodopsin. Thus, the fast regenerating fraction (20%) corresponds approximately to the fraction of the total ERP independently estimated to arise from M-opsin. Because both phases of the ERP recover substantially faster than previous measurements of bulk rhodopsin regeneration in living mice, we conclude that delivery of the highly hydrophobic 11-cis retinal to the interior of rod photoreceptors appears to be retarded by transit across the cytoplasmic gap between plasma and disc membranes. PMID:24801306

  7. Silver nanowire catalysts on carbon nanotubes-incorporated bacterial cellulose membrane electrodes for oxygen reduction reaction.

    PubMed

    Kim, Bona; Choi, Youngeun; Cho, Se Youn; Yun, Young Soo; Jin, Hyoung-Joon

    2013-11-01

    Silver nanowires have unique electrical, thermal and optical properties, which support their potential application in numerous fields including catalysis, electronics, optoelectronics, sensing, and surface-enhanced spectroscopy. Especially, their application such as catalysts for alkaline fuel cells (AFCs) have attracted much interest because of their superior electrical conductivity over that of any metal and their lower cost compared to Pt. In this study, multiwalled carbon nanotubes (MWCNTs)-incorporated bacterial cellulose (BC) membrane electrode with silver nanowire catalyst was prepared. First, acid-treated MWCNTs were incorporated into BC membranes and then freeze-dried after solvent exchange to tert-butanol in order to maintain the 3D-network macroporous structure. Second, silver nanowires synthesized by polyol process were introduced onto the surface of the MWCNTs-incorporated BC membrane through easy vacuum filtration. Finally, thermal treatment was carried out to confirm the effect of the PVP on the silver nanowire catalysts toward oxygen reduction reaction. The electrode with thermally treated silver nanowire had great electrocatalytic activity compared with non-treated one. These results suggest that the MWCNTs-incorporated BC electrode with silver nanowire catalysts after thermal treatment could be potentially used in cathodes of AFCs.

  8. Composite membrane of niobium(V) oxide and cellulose acetate: Preparation and characterization

    SciTech Connect

    Campos, E.A.; Gushikem, Y.

    1997-09-01

    Composite membranes of niobium(V) oxide and cellulose acetate (Cel/Nb{sub 2}O{sub 5}) were prepared with the following Nb{sub 2}O{sub 5} loadings (in wt%): 1.1, 6.1, 9.8, 15.6, and 20.9. The thermal stability of the membranes slightly decreased in relation to the pure membrane on incorporation of the metal oxide into the matrix. Scanning electron microscopy and niobium mapping with an X-ray EDS microprobe showed that the metal oxide particles are homogeneously dispersed in the matrix. The electronic absorption bands indicated that the oxide particle size varies from that of the monomer to those of oligomer species on increased Nb{sub 2}O{sub 5} loading in the matrix. The dispersed oxide possesses mainly Lewis acid character, a clear indication that on increasing the oxide loading in the matrix, the coordination number of the metal is not saturated by formation of the Nb-O-Nb bond. These materials can be useful in ion-exchange process, as supports for enzymes, in catalytic reactions, and in reverse osmosis experiments.

  9. Synergistic Effect of Functionalized Nanokaolin Decorated MWCNTs on the Performance of Cellulose Acetate (CA) Membranes Spectacular

    PubMed Central

    Afzal, Amina; Rafique, Muhammad Shahid; Iqbal, Nadeem; Qaiser, Asif Ali; Anwar, Abdul Waheed; Iqbal, Sadia Sagar

    2016-01-01

    In order to enhance salt rejection level and high pressure mechanical integrity, functionalized nanokaolin decorated multiwall carbon nanotubes (FNKM, 0–5 wt % loading) were incorporated into a cellulose acetate (CA) matrix using high temperature solution mixing methodology. Scanning electron microscopy (SEM), X-ray diffraction technique (XRD), thermo-gravimetric analyzer (TGA) and Fourier transform infrared spectrometer (FTIR) were used to characterize the prepared membranes. The obtained results revealed that with increasing FNKM concentration in the host polymeric matrix, composite membrane’s structural, functional, thermal, water permeation/flux and salt rejection characteristics were also modified accordingly. Percent enhancement in salt rejection was increased around threefold by adding 5 wt % FNKM in CA. PMID:28335207

  10. [Healing of osseous defects by guided bone regeneration using ribose cross linked collagen membranes].

    PubMed

    Tal, H

    2004-07-01

    The ultimate goal of periodontal therapy has long been the complete regeneration of the periodontal attachment apparatus. Guided Tissue Regeneration (GTR) and Guided Bone Regeneration (GBR) are two regenerative procedures which converted this goal from a dream to reality. In search of a biocompatible resorbable tissue barrier, collagen, being a natural protein and a weak antigen, has attracted much interest and became the focus of much intention during the 80's and the 90's. The understanding that cross linking of collagen with aldehyde sugars, especially ribose, produces collagen which is highly resistant to resorption in vivo led to the development of a "natural" Crossed-Linked Collagen Barrier (CB-SX). Animal and Human studies have shown that the newly developed membrane is biocompatible, remains intact in the tissues 6 months and more, and results in impressive guided tissue/bone regeneration. Spontaneous early exposure of the membrane is common but the healing potential of the resulted tissue dehiscence is favorable with no tendency for bacterial infection. The commercial version of the CB-SX is especially suitable for GBR procedures; it is highly recommended that the gingival flaps involved will properly be released, will lack tension, and be thoroughly sutured.

  11. Ammonium nitrogen removal from the permeates of anaerobic membrane bioreactors: economic regeneration of exhausted zeolite.

    PubMed

    Deng, Qiaosi; Dhar, Bipro Ranjan; Elbeshbishy, Elsayed; Lee, Hyung-Sool

    2014-08-01

    This study revealed that ammonium exchange of natural zeolite could be an economical method of nitrogen removal from the permeates of anaerobic membrane bioreactors (AnMBRs). It was found that the mass ratio of Na+ to Zeolite - NH4+ - N significantly affected regeneration efficiency (RE), not simply NaCI concentration. Batch experiments showed that the mass ratio of 750g Na+/g Zeolite - NH4+ - N was required to achieve RE over 90% in 2h at pH 9. However, the alkaline regeneration at pH 12 significantly decreased the mass ratio down to 4.2 in batch tests. It was confirmed that the alkaline regeneration only needed NaCl 10 g/L (the mass of Na+ to Zeolite - NH4+ - N of 4.2) for RE of 85% in 2 h of reaction time in continuous column tests. Economic analysis showed that this alkaline regeneration decreased chemical costs over 10 times as compared with a conventional regeneration method. A significant bottleneck of zeolite processes would be the requirement of substituting exhausted zeolite with virgin one, due to the reductions of ammonium exchange capacity and RE.

  12. Utilizing collagen membranes for guided tissue regeneration-based root coverage.

    PubMed

    Wang, Hom-Lay; Modarressi, Marmar; Fu, Jia-Hui

    2012-06-01

    Gingival recession is a common clinical problem that can result in hypersensitivity, pain, root caries and esthetic concerns. Conventional soft tissue procedures for root coverage require an additional surgical site, thereby causing additional trauma and donor site morbidity. In addition, the grafted tissues heal by repair, with formation of long junctional epithelium with some connective tissue attachment. Guided tissue regeneration-based root coverage was thus developed in an attempt to overcome these limitations while providing comparable clinical results. This paper addresses the biologic foundation of guided tissue regeneration-based root coverage, and describes the indications and contraindications for this technique, as well as the factors that influence outcomes. The step-by-step clinical techniques utilizing collagen membranes are also described. In comparison with conventional soft tissue procedures, the benefits of guided tissue regeneration-based root coverage procedures include new attachment formation, elimination of donor site morbidity, less chair-time, and unlimited availability and uniform thickness of the product. Collagen membranes, in particular, benefit from product biocompatibility with the host, while promoting chemotaxis, hemostasis, and exchange of gas and nutrients. Such characteristics lead to better wound healing by promoting primary wound coverage, angiogenesis, space creation and maintenance, and clot stability. In conclusion, collagen membranes are a reliable alternative for use in root coverage procedures.

  13. Platelet adhesion, contact phase coagulation activation, and C5a generation of polyethylene glycol acid-grafted high flux cellulosic membrane with varieties of grafting amounts.

    PubMed

    Fushimi, F; Nakayama, M; Nishimura, K; Hiyoshi, T

    1998-10-01

    Grafting of polyethylene glycol chains onto cellulosic membrane can be expected to reduce the interaction between blood (plasma protein and cells) and the membrane surface. Alkylether carboxylic acid (PEG acid) grafted high flux cellulosic membranes for hemodialysis, in which the polyethylene glycol chain bears an alkyl group at one side and a carboxyl group at the other side, have been developed and evaluated. PEG acid-grafted high flux cellulosic membranes with various grafting amounts have been compared with respect to platelet adhesion, the contact phase of blood coagulation, and complement activation in vitro. A new method of quantitating platelet adhesion on hollow-fiber membrane surfaces has been developed, which is based on the determination of lactate dehydrogenase (LDH) activity after lysis of the adhered platelets. PEG acid-grafted high flux cellulosic membranes showed reduced platelet adhesion and complement activation effects in grafting amounts of 200 ppm or higher without detecting adverse effects up to grafting amounts of 850 ppm. The platelet adhesion of a PEG acid-grafted cellulosic membrane depends on both the flux and grafting amounts of the membrane. It is concluded that the grafting of PEG acid onto a cellulosic membrane improves its biocompatibility as evaluated in terms of platelet adhesion, complement activation, and thrombogenicity.

  14. Patterning and lifetime of plasma membrane-localized cellulose synthase is dependent on actin organization in Arabidopsis interphase cells.

    PubMed

    Sampathkumar, Arun; Gutierrez, Ryan; McFarlane, Heather E; Bringmann, Martin; Lindeboom, Jelmer; Emons, Anne-Mie; Samuels, Lacey; Ketelaar, Tijs; Ehrhardt, David W; Persson, Staffan

    2013-06-01

    The actin and microtubule cytoskeletons regulate cell shape across phyla, from bacteria to metazoans. In organisms with cell walls, the wall acts as a primary constraint of shape, and generation of specific cell shape depends on cytoskeletal organization for wall deposition and/or cell expansion. In higher plants, cortical microtubules help to organize cell wall construction by positioning the delivery of cellulose synthase (CesA) complexes and guiding their trajectories to orient newly synthesized cellulose microfibrils. The actin cytoskeleton is required for normal distribution of CesAs to the plasma membrane, but more specific roles for actin in cell wall assembly and organization remain largely elusive. We show that the actin cytoskeleton functions to regulate the CesA delivery rate to, and lifetime of CesAs at, the plasma membrane, which affects cellulose production. Furthermore, quantitative image analyses revealed that actin organization affects CesA tracking behavior at the plasma membrane and that small CesA compartments were associated with the actin cytoskeleton. By contrast, localized insertion of CesAs adjacent to cortical microtubules was not affected by the actin organization. Hence, both actin and microtubule cytoskeletons play important roles in regulating CesA trafficking, cellulose deposition, and organization of cell wall biogenesis.

  15. Membranes for periodontal regeneration: From commercially available to spatially designed and functionally graded materials

    NASA Astrophysics Data System (ADS)

    Bottino, Marco Cicero

    The aging of the global population will lead to a considerable increase in the number of surgical and restorative procedures related to oral rehabilitation or periodontal regeneration. Periodontitis is one of the most aggressive pathologies that concern the integrity of the periodontal system that can lead to the destruction of the periodontium. Guided tissue and guided bone regeneration (GTR/GBR) have been used for the repair and regeneration of periodontal tissues by utilizing an occlusive membrane. The goal of this dissertation is to advance the knowledge in the area of periodontal regeneration by investigating the properties of a commercially available freeze-dried collagen-based graft (AlloDermRTM) and by designing/fabricating a functionally graded membrane (FGM) via multilayer electrospinning. The effects of different rehydration times and of a simultaneous rehydration/crosslinking procedure on the biomechanical properties and matrix stability of the commercially available membrane were investigated. The results revealed that there are significant changes on the biomechanical properties of the graft as rehydration time increases. Moreover, it was demonstrated that the simultaneous rehydration/crosslinking protocol has a synergistic effect in terms of enhancing biomechanical properties. A FGM consisting of a core-layer (CL) and two functional surface-layers (SL) was fabricated via sequential electrospinning. Hydroxyapatite nanoparticles (n-HAp) were incorporated to enhance bone formation (SL facing bone defect), and metronidazole benzoate (MET) was added to prevent bacterial colonization (SL facing the epithelial tissue). Degradation studies performed on both the CL and the FGM confirmed that the design holds promise in terms of providing the required mechanical stability to avoid membrane collapse and, therefore, enhance bone regeneration. Finally, it was demonstrated that MET incorporation into the SL that would face epithelial tissue is effective in

  16. Phenotype expression of gingival fibroblasts cultured on membranes used in guided tissue regeneration.

    PubMed

    Locci, P; Calvitti, M; Belcastro, S; Pugliese, M; Guerra, M; Marinucci, L; Staffolani, N; Becchetti, E

    1997-09-01

    Human gingival fibroblasts were cultured in vitro using as substrates an extracellular matrix (matrix) and polytetrafluoride (PTFE) membranes, which are used in guided tissue regeneration. To test the degree of biocompatibility of these membranes, the cellular proliferation and the accumulation of extracellular matrix (ECM) macromolecules were considered as parameters. The fibroblasts were cultured in vitro for 24 and 48 hours without serum on plastic, matrix, and PTFE membranes in the presence of 3H-thymidine, 3H-glucosamine, and 3H-proline to study the neo-synthesis of DNA, glycosaminoglycans (GAG), and collagen proteins, respectively. Studies on cell proliferation showed that fibroblasts grown on matrix membrane significantly increased 3H-thymidine incorporation, while fibroblasts grown on PTFE membrane decreased 3H-thymidine incorporation, compared to plastic used as a control. Moreover, the PTFE membrane induced a marked decrease of collagen and GAG accumulation both in the cellular and extracellular pool, while the matrix membrane provoked a decrease of the two macromolecules in the cellular pool and an increase in the extracellular one, compared to the control. The data we obtained demonstrate that matrix membranes are the most suitable to stimulate both cellular proliferation and ECM macromolecule accumulation.

  17. Protein adsorption capability on polyurethane and modified-polyurethane membrane for periodontal guided tissue regeneration applications.

    PubMed

    Sheikh, Zeeshan; Khan, Abdul Samad; Roohpour, Nima; Glogauer, Michael; Rehman, Ihtesham U

    2016-11-01

    Periodontal disease if left untreated can result in creation of defects within the alveolar ridge. Barrier membranes are frequently used with or without bone replacement graft materials for achieving periodontal guided tissue regeneration (GTR). Surface properties of barrier membranes play a vital role in their functionality and clinical success. In this study polyetherurethane (PEU) membranes were synthesized by using 4,4'-methylene-diphenyl diisocyanate (MDI), polytetramethylene oxide (PTMO) and 1,4-butane diol (BDO) as a chain extender via solution polymerization. Hydroxyl terminated polydimethylsiloxane (PDMS) due to having inherent surface orientation towards air was used for surface modification of PEU on one side of the membranes. This resulting membranes had one surface being PEU and the other being PDMS coated PEU. The prepared membranes were treated with solutions of bovine serum albumin (BSA) in de-ionized water at 37°C at a pH of 7.2. The surface protein adsorptive potential of PEU membranes was observed using Attenuated Total Reflectance Fourier Transform Infrared Spectroscopy (ATR-FTIR), Raman spectroscopy and Confocal Raman spectroscopy. The contact angle measurement, tensile strength and modulus of prepared membranes were also evaluated. PEU membrane (89.86±1.62°) exhibited less hydrophobic behavior than PEU-PDMS (105.87±3.16°). The ultimate tensile strength and elastic modulus of PEU (27±1MPa and 14±2MPa) and PEU-PDMS (8±1MPa and 26±1MPa) membranes was in required range. The spectral analysis revealed adsorption of BSA proteins on the surface of non PDMS coated PEU surface. The PDMS modified PEU membranes demonstrated a lack of BSA adsorption. The non PDMS coated side of the membrane which adsorbs proteins could potentially be used facing towards the defect attracting growth factors for periodontal tissue regeneration. Whereas, the PDMS coated side could serve as an occlusive barrier for preventing gingival epithelial cells from

  18. Electrophoretic deposition of cellulose nanocrystals (CNs) and CNs/alginate nanocomposite coatings and free standing membranes.

    PubMed

    Chen, Qiang; de Larraya, Uxua Pérez; Garmendia, Nere; Lasheras-Zubiate, María; Cordero-Arias, Luis; Virtanen, Sannakaisa; Boccaccini, Aldo R

    2014-06-01

    This study presents the electrophoretic deposition (EPD) of cellulose nanocrystals (CNs) and CNs-based alginate composite coatings for biomedical applications. The mechanism of anodic deposition of CNs and co-deposition of CNs/alginate composites was analyzed based on the results of zeta-potential, Fourier transform infrared spectroscopy and scanning electron microscopy (SEM) analyses. The capability of the EPD technique for manipulating the orientation of CNs and for the preparation of multilayer CNs coatings was demonstrated. The nanotopographic surface roughness and hydrophilicity of the deposited coatings were measured and discussed. Electrochemical testing demonstrated that a significant degree of corrosion protection of stainless steel could be achieved when CNs-containing coatings were present. Additionally, the one-step EPD-based processing of free-standing CNs/alginate membranes was demonstrated confirming the versatility of EPD to fabricate free-standing membrane structures compared to a layer-by-layer deposition technique. CNs and CNs/alginate nanocomposite coatings produced by EPD are potential candidates for biomedical, cell technology and drug delivery applications.

  19. Cellulose acetate hollow fiber membranes blended with phospholipid polymer and their performance for hemopurification.

    PubMed

    Ye, Sang Ho; Watanabe, Junji; Ishihara, Kazuhiko

    2004-01-01

    Commercially available hollow fiber membranes (HFMs) made from synthetic polymers, including cellulose acetate (CA) HFMs, used as hemopurification membranes, need to improve in hemocompatibility, by suppressing protein adsorption and clot formation. In this study, CA HFMs blended with 2-methacryloyloxyethyl phosphorylcholine (MPC) copolymer (PMB30 composed of MPC and n-butyl methacrylate (BMA)) were prepared by a dry-jet wet spinning process. Their performances were evaluated by characterizing their properties such as structure, permeability and protein adsorption. CA/PMB30-blend HFMs showed structure changes such as increase of porosity, development of large pores and decreasing of the thickness of the active layer. And the structure and permeability of CA/PMB30-blend HFMs were controllable by changing preparation conditions. Also, the CA/PMB30-blend HFMs had good permeability, low protein adsorption and low fouling property during the permeability experiment in comparison with CA HFMs, because the hydrophilic and hemocompatible MPC copolymer (PMB30) existed on the surface of the HFM.

  20. Attachment, proliferation and differentiation of periodontal ligament cells on various guided tissue regeneration membranes.

    PubMed

    Takata, T; Wang, H L; Miyauchi, M

    2001-10-01

    The purpose of this study was to evaluate the biological effects of guided tissue regeneration (GTR) membrane materials, per se, on the periodontal tissue regeneration. Rat periodontal ligament (PDL)-derived cells were used to study the attachment, proliferation and differentiation, in vitro, on various GTR membranes. Five commercially available membranes bovine type I collagen (BioMend; BM), bovine type I atelocollagen (Tissue Guide; TG), polylactic acid (Epi-Guide; EG), co-polymer of polylactic acid and polyglycolic acid (Resolute; RL) and expanded polytetrafluoroethylene: e-PTFE (Gore Tex; GT)-were examined. A 3 x 3 mm section of the membrane was fixed to the bottom of a 35 x 10 mm style culture dish and plated with 2 ml of cell suspension at an initial density of 5 x 10(4) cells/ml in culture medium with 10% fetal bovine serum. For cell growth analysis, the specimens were fixed with 10% buffered formalin and stained with hematoxylin at 1.5 hours and 1, 3 and 5 days after cell seeding. The number of cells included in a unit area of 0.25 mm2 were counted under light microscopy. As a comparative scaffold of cell proliferation, a plastic cover for cell culture slip (Celldesk; CD) was used. For analysis of cell differentiation, activity of alkaline phosphatase (ALP) and calcification were histochemically revealed after 2-week cultivation. The initial number of PDL cells attached to the membrane at 1.5 hours after cell seeding was different among membranes. RL, TG and EG had the same level of attached cell numbers as that on CD, while the cell numbers on GT and BM were significantly lower than that on CD (p < 0.01). The rate of cell proliferation with time also differed among the membranes examined. RL and BM demonstrated a significantly higher number of cells at 5 days than at 1.5 hours (p < 0.01). TG had increased numbers of cells at 3 and 5 days after cell seeding. However, there was no statistical difference between the cell numbers at 1.5 hours and 5 days after

  1. A chemical genetics approach reveals H,K-ATPase-mediated membrane voltage is required for planarian head regeneration.

    PubMed

    Beane, Wendy S; Morokuma, Junji; Adams, Dany S; Levin, Michael

    2011-01-28

    Biophysical signaling is required for both embryonic polarity and regenerative outgrowth. Exploiting endogenous ion transport for regenerative therapies will require direct regulation of membrane voltage. Here, we develop a pharmacological method to target ion transporters, uncovering a role for membrane voltage as a key regulator of anterior polarity in regenerating planaria. Utilizing the highly specific inhibitor, SCH-28080, our data reveal that H(+),K(+)-ATPase-mediated membrane depolarization is essential for anterior gene expression and brain induction. H(+),K(+)-ATPase-independent manipulation of membrane potential with ivermectin confirms that depolarization drives head formation, even at posterior-facing wounds. Using this chemical genetics approach, we demonstrate that membrane voltage controls head-versus-tail identity during planarian regeneration. Our data suggest well-characterized drugs (already approved for human use) might be exploited to control adult stem cell-driven pattern formation during the regeneration of complex structures.

  2. Drug loaded homogeneous electrospun PCL/gelatin hybrid nanofiber structures for anti-infective tissue regeneration membranes.

    PubMed

    Xue, Jiajia; He, Min; Liu, Hao; Niu, Yuzhao; Crawford, Aileen; Coates, Phil D; Chen, Dafu; Shi, Rui; Zhang, Liqun

    2014-11-01

    Infection is the major reason for guided tissue regeneration/guided bone regeneration (GTR/GBR) membrane failure in clinical application. In this work, we developed GTR/GBR membranes with localized drug delivery function to prevent infection by electrospinning of poly(ε-caprolactone) (PCL) and gelatin blended with metronidazole (MNA). Acetic acid (HAc) was introduced to improve the miscibility of PCL and gelatin to fabricate homogeneous hybrid nanofiber membranes. The effects of the addition of HAc and the MNA content (0, 1, 5, 10, 20, 30, and 40 wt.% of polymer) on the properties of the membranes were investigated. The membranes showed good mechanical properties, appropriate biodegradation rate and barrier function. The controlled and sustained release of MNA from the membranes significantly prevented the colonization of anaerobic bacteria. Cells could adhere to and proliferate on the membranes without cytotoxicity until the MNA content reached 30%. Subcutaneous implantation in rabbits for 8 months demonstrated that MNA-loaded membranes evoked a less severe inflammatory response depending on the dose of MNA than bare membranes. The biodegradation time of the membranes was appropriate for tissue regeneration. These results indicated the potential for using MNA-loaded PCL/gelatin electrospun membranes as anti-infective GTR/GBR membranes to optimize clinical application of GTR/GBR strategies.

  3. Investigating the Potential of Amnion-Based Scaffolds as a Barrier Membrane for Guided Bone Regeneration.

    PubMed

    Li, Wuwei; Ma, Guowu; Brazile, Bryn; Li, Nan; Dai, Wei; Butler, J Ryan; Claude, Andrew A; Wertheim, Jason A; Liao, Jun; Wang, Bo

    2015-08-11

    Guided bone regeneration is a new concept of large bone defect therapy, which employs a barrier membrane to afford a protected room for osteogenesis and prevent the invasion of fibroblasts. In this study, we developed a novel barrier membrane made from lyophilized multilayered acellular human amnion membranes (AHAM). After decellularization, the AHAM preserved the structural and biomechanical integrity of the amnion extracellular matrix (ECM). The AHAM also showed minimal toxic effects when cocultured with mesenchymal stem cells (MSCs), as evidenced by high cell density, good cell viability, and efficient osteogenic differentiation after 21-day culturing. The effectiveness of the multilayered AHAM in guiding bone regeneration was evaluated using an in vivo rat tibia defect model. After 6 weeks of surgery, the multilayered AHAM showed great efficiency in acting as a shield to avoid the invasion of the fibrous tissues, stabilizing the bone grafts and inducing the massive bone growth. We hence concluded that the advantages of the lyophilized multilayered AHAM barrier membrane are as follows: preservation of the structural and mechanical properties of the amnion ECM, easiness for preparation and handling, flexibility in adjusting the thickness and mechanical properties to suit the application, and efficiency in inducing bone growth and avoiding fibrous tissues invasion.

  4. Preparation and evaluation of water-in-soybean oil-in-water emulsions by repeated premix membrane emulsification method using cellulose acetate membrane.

    PubMed

    Muhamad, Ida Idayu; Quin, Chang Hui; Selvakumaran, Suguna

    2016-04-01

    The purpose of this study was to investigate the preparation of formulated water- in-soybean oil-in-water emulsions by repeated premix membrane emulsification method using a cellulose acetate membrane. The effect of selective membrane emulsification process parameters (concentration of the emulsifiers, number of passes of the emulsions through the membrane and storage temperature) on the properties and stability of the developed emulsions were also investigated. 1, 3, 6, 8-pyrenetetrasulfonic acid tetrasodium salt (PTSA) was used as a hydrophilic model ingredient for the encapsulation of bioactive substances. W/O emulsions with 7 wt% (weight percentage) PGPR displays homogeneous and very fine dispersions, with the median diameter at 0.640 μm. Meanwhile, emulsions prepared by membrane emulsification (fine W/O/W) showed the highest stability at Tween 80 concentrations of 0.5 wt.% (weight percentage). It concluded that at 7 wt.% (weight percentage) PGPR concentration and 0.5 wt.% (weight percentage) Tween 80 concentrations, the most uniform particles with minimum mean size of oil drops (9.926 μm) were obtained after four passes through the membrane. Thus, cellulose acetate membrane can be used for preparing a stable W/O/W emulsions by repeated premix ME due to low cost and relatively easy to handle.

  5. KOBITO1 encodes a novel plasma membrane protein necessary for normal synthesis of cellulose during cell expansion in Arabidopsis.

    PubMed

    Pagant, Silvère; Bichet, Adeline; Sugimoto, Keiko; Lerouxel, Olivier; Desprez, Thierry; McCann, Maureen; Lerouge, Patrice; Vernhettes, Samantha; Höfte, Herman

    2002-09-01

    The cell wall is the major limiting factor for plant growth. Wall extension is thought to result from the loosening of its structure. However, it is not known how this is coordinated with wall synthesis. We have identified two novel allelic cellulose-deficient dwarf mutants, kobito1-1 and kobito1-2 (kob1-1 and kob1-2). The cellulose deficiency was confirmed by the direct observation of microfibrils in most recent wall layers of elongating root cells. In contrast to the wild type, which showed transversely oriented parallel microfibrils, kob1 microfibrils were randomized and occluded by a layer of pectic material. No such changes were observed in another dwarf mutant, pom1, suggesting that the cellulose defect in kob1 is not an indirect result of the reduced cell elongation. Interestingly, in the meristematic zone of kob1 roots, microfibrils appeared unaltered compared with the wild type, suggesting a role for KOB1 preferentially in rapidly elongating cells. KOB1 was cloned and encodes a novel, highly conserved, plant-specific protein that is plasma membrane bound, as shown with a green fluorescent protein-KOB1 fusion protein. KOB1 mRNA was present in all organs investigated, and its overexpression did not cause visible phenotypic changes. KOB1 may be part of the cellulose synthesis machinery in elongating cells, or it may play a role in the coordination between cell elongation and cellulose synthesis.

  6. Comparison of silkworm-cocoon-derived silk membranes of two different thicknesses for guided bone regeneration.

    PubMed

    Seok, Hyun; Kim, Min Keun; Kim, Seong-Gon; Kweon, HaeYong

    2014-11-01

    The objective of this study was to compare the effectiveness of silk membranes (SMs) of different thicknesses for guided bone regeneration. Two kinds of SMs were prepared (SM1: 0.01 mm thickness, SM2: 0.5 mm thickness). Before use in animal experiments, scanning electron microscope images were taken to examine the gross morphology of each membrane. Ten New Zealand white rabbits were used for this study. Bilateral round-shaped defects were created in the parietal bone (diameter: 8.0 mm) and each defect was covered with SM1 or SM2. Animals were killed at 4 weeks and 8 weeks. Bone regeneration was analyzed in each specimen by micro-computed tomography (μ-CT) and histological analysis. In the μ-CT analysis, the average amount of newly formed bone in the SM2 group was greater than that in the SM1 group. There was a significant difference at 4 weeks after surgery (P = 0.004). In the histological analysis, the amount of formed lamellar bone was much greater in the SM2 group than in the SM1 group at 8 weeks after surgery (P = 0.021). In conclusion, the thick SM was much more effective for bone regeneration of bone defects than the thin SM.

  7. Methanogenic degradation of toilet-paper cellulose upon sewage treatment in an anaerobic membrane bioreactor at room temperature.

    PubMed

    Chen, Rong; Nie, Yulun; Kato, Hiroyuki; Wu, Jiang; Utashiro, Tetsuya; Lu, Jianbo; Yue, Shangchao; Jiang, Hongyu; Zhang, Lu; Li, Yu-You

    2017-03-01

    Toilet-paper cellulose with rich but refractory carbon sources, are the main insoluble COD fractions in sewage. An anaerobic membrane bioreactor (AnMBR) was configured for sewage treatment at room temperature and its performance on methanogenic degradation of toilet paper was highlighted. The results showed, high organic removal (95%), high methane conversion (90%) and low sludge yield (0.08gVSS/gCOD) were achieved in the AnMBR. Toilet-paper cellulose was fully biodegraded without accumulation in the mixed liquor and membrane cake layer. Bioconversion efficiency of toilet paper approached 100% under a high organic loading rate (OLR) of 2.02gCOD/L/d and it could provide around 26% of total methane generation at most of OLRs. Long sludge retention time and co-digestion of insoluble/soluble COD fractions achieving mutualism of functional microorganisms, contributed to biodegradation of toilet-paper cellulose. Therefore the AnMBR successfully implemented simultaneously methanogenic bioconversion of toilet-paper cellulose and soluble COD in sewage at room temperature.

  8. Preparation of biodegradable PLA/PLGA membranes with PGA mesh and their application for periodontal guided tissue regeneration.

    PubMed

    Kim, Eun Jin; Yoon, Suk Joon; Yeo, Guw-Dong; Pai, Chaul-Min; Kang, Inn-Kyu

    2009-10-01

    A biodegradable polylactic acid (PLA)/poly(glycolide-co-lactide) copolymer (PLGA) membrane with polyglycolic acid (PGA) mesh was prepared to aid the effective regeneration of defective periodontal tissues. The microporous membrane used in this study consists of biodegradable polymers, and seems to have a structure to provide appropriate properties for periodontal tissue regeneration. Based on the albumin permeation test, it is known that the biodegradable membrane exhibits the suitable permeability of nutrients. The membrane maintained its physical integrity for 6-8 weeks, which could be sufficient to retain space in the periodontal pocket. Cell attachment and cytotoxicity tests were performed with respect to the evaluation of biocompatibility of the membrane. As a result, the membrane did not show any cytotoxicity. The safety and therapeutic efficacies of the biodegradable membranes were confirmed in animal tests.

  9. Layer-by-layer structured polysaccharides-based multilayers on cellulose acetate membrane: Towards better hemocompatibility, antibacterial and antioxidant activities

    NASA Astrophysics Data System (ADS)

    Peng, Lincai; Li, Hui; Meng, Yahong

    2017-04-01

    The development of multifunctional cellulose acetate (CA) membranes with enhanced hemocompatibility and antibacterial and antioxidant activities is extremely important for biomedical applications. In this work, significant improvements in hemocompatibility and antibacterial and antioxidant activities of cellulose acetate (CA) membranes were achieved via layer-by-layer (LBL) deposition of chitosan (CS) and water-soluble heparin-mimicking polysaccharides (i.e., sulfated Cantharellus cibarius polysaccharides, SCP) onto their surface. The surface chemical compositions, growth manner, surface morphologies, and wetting ability of CS/SCP multilayer-modified CA membranes were characterized, respectively. The systematical evaluation of hemocompatibility revealed that CS/SCP multilayer-modified CA membranes significantly improved blood compatibility including resistance to non-specific protein adsorption, suppression of platelet adhesion and activation, prolongation of coagulation times, inhibition of complement activation, as well as reduction in blood hemolysis. Meanwhile, CS/SCP multilayer-modified CA membranes exhibited strong growth inhibition against Escherichia coli and Staphylococcus aureus, as well as high scavenging abilities against superoxide and hydroxyl radicals. In summary, the CS/SCP multilayers could confer CA membranes with integrated hemocompatibility and antibacterial and antioxidant activities, which might have great potential application in the biomedical field.

  10. Synthesis and one-pot tethering of hydroxyl-capped phosphorylcholine onto cellulose membrane for improving hemocompatibility and antibiofouling property.

    PubMed

    Yuan, Jiang; Tong, Ling; Yi, Huaixiang; Wang, Bingxiang; Shen, Jian; Lin, Sicong

    2013-11-01

    Tethering of biomimetic phosphorylcholine derivative onto the surface of biomedical devices is an effective method for improving hemocompatibility and antibiofouling property. Herein, series of novel hydroxyl-capped phosphorylcholines (HOPC) with different carbon spacer lengths were first synthesized and characterized with element analysis (EA), Fourier transform infrared spectroscopy(FTIR), and nuclear magnetic resonance spectroscopy (NMR). Then, HOPC (n=5, 2a) was one-pot tethered onto cellulose membrane with hexamethylene diisocyanate (HDI) as a coupling agent. The existence of phosphorylcholine was demonstrated by water contact angle measurement, attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS). The hemocompatibility and antibiofouling property were evaluated by hemolytic test, platelet adhesion, protein adsorption, and Escherichia coli adhesion test. The results showed that cellulose membranes tethered with HOPC exhibited excellent hemocompatibility featured by low platelet adhesion and fibrinogen adsorption as well as antibiofouling property with bacterial adhesion resistance.

  11. Microvessel basement membrane reduplication is not associated with repeated nerve fiber degeneration and regeneration.

    PubMed

    Baker, M K; Bourque, P; Dyck, P J

    1996-03-01

    To determine whether repeated nerve fiber degeneration and regeneration can induce reduplication of endoneurial microvessel basement membranes (BMs), typical of such conditions as diabetic polyneuropathy, electronmicrographs of endoneurial microvessels of rat peroneal and tibial nerves were studied in repeatedly crushed (10 x) sciatic nerves and compared to microvessels of sham-operated uncrushed nerves. On average, crushed nerves had 2.6, SE +/- 0.1 BMs, whereas control nerves had 2.7, SE +/- 0.1 (P > 0.05). Microvessel cellular components were significantly increased in both number and size in the crushed nerves. These nerves also demonstrated a trend to increased vessel numbers and density. These results are not in keeping with the hypothesis that BM reduplication of endoneurial microvessels is simply due to repeated fiber degeneration and regeneration.

  12. In vivo and in vitro degradation of a novel bioactive guided tissue regeneration membrane.

    PubMed

    Nieminen, T; Kallela, I; Keränen, J; Hiidenheimo, I; Kainulainen, H; Wuolijoki, E; Rantala, I

    2006-08-01

    The aim of this study was to assess degradation of a novel bioactive guided tissue regeneration (GTR) membrane and to quantify the concurrent tissue responses. Pieces of membrane composed of poly-l-lactide, poly-d,l-lactide, trimethylenecarbonate and polyglycolide were dipped into an N-methyl-2-pyrroline (NMP) solution and implanted in the mandibles of 10 sheep. The animals were sacrificed at 6-104 weeks. Parallel in vitro degradation was analysed by measuring the inherent viscosity, water absorption and remaining mass. One of the 2 in vitro sets of membranes was prehandled with NMP. At 6-26 weeks in vivo, the gradually more degraded implants were surrounded by a fibrous network. At 52 and 104 weeks, the implants and fibrous networks were non-detectable. Foreign body granulomatous reactions were not observed. In vitro, the mass of the NMP-exposed membranes diminished linearly over the 2-year period down to 10%, while the non-NMP-exposed membrane maintained all their mass for the first 16 weeks. The membranes without NMP had absorbed significantly less water at weeks 4 and 8 than the other group. The inherent viscosity decreased relatively uniformly in the in vitro groups. In conclusion, the in vivo degradation was complete in 12 months with only mild histologic responses; the degradation in vitro may be slower. NMP accelerates the degradation.

  13. Composites PVDF-TrFE/BT used as bioactive membranes for enhancing bone regeneration

    NASA Astrophysics Data System (ADS)

    Gimenes, Rossano; Zaghete, Maria A.; Bertolini, Marcio; Varela, Jose A.; Coelho, Luciane O.; Silva, Nelson F., Jr.

    2004-07-01

    In this paper a piezoelectric composite membranes were developed for charge generator to promoter bone regeneration on defects sites. Is known that the osteogenesis process is induced by interactions between biological mechanisms and electrical phenomena. The membranes were prepared by mixing Barium Titanate (BT) powders and PVDF-TrFE (PVDF:TrFE = 60:40 mol%) on dimethylformamide medium. This precursor solution was dried and crystallized at 100oC for 12 hours. Composites membranes were obtained by following methods: solvent casting (SC), spincoating (SP), solvent extraction by water addition (WS) and hot pressing (HP). The microstructural analysis performed by SEM showed connectivity type 3-0 and 3-1 with high homogeneity for samples of ceramic volume fraction major than 0.50. Powder agglomerates within the polymer matrix was evidenced were observed for composites with the BT volume fraction major than 40%. The composite of ceramic fraction of 0.55 presented the best values of remanent polarization (~33mC/cm2), but the flexibility of these composites with the larger ceramic fraction was significantly affected. For in vivo evaluation PVDF-TrFE/BT 90/10 membranes with 3cm larger were longitudinally implanted under tibiae of male rabbit. After 21 days the animals were sacrificed. By histological analyses were observed neo formed bone with a high mitotic activity. In the interface bone-membrane was evidenced a pronounced callus formation. These results encourage further applications of these membranes in bone-repair process.

  14. Effect of a collagen membrane enriched with fibronectin on guided tissue regeneration in dogs.

    PubMed

    Kurtis, Bülent; Balos, Köksal; Oygür, Tülin

    2002-01-01

    The present study was planned to assess the capacity of a resorbable collagen membrane enriched with fibronectin to prevent the apical migration of epithelium and to facilitate new attachment and new bone. Experimental osseous dehiscence defects were produced on the bilateral labial aspect of mandibular 2nd, 3rd and 4th premolar teeth in six mongrel dogs. Guided tissue regeneration therapy using collagen membranes, which were rehydrated with fibronectin solution, was performed on one quadrant (group A). In the contralateral quadrant, the same collagen membranes, but rehydrated only with saline (group B), were placed over the bony defects. The third premolar teeth, which were treated by open-flap debridement, served as control (group C). Flaps were positioned slightly coronally and sutured; sutures were removed 10 days later. The dogs were killed 30 days after reconstructive therapy. Tissue blocks containing the experimental and control teeth were excised, demineralized in EDTA, and embedded in paraffin. Histological and histometric evaluation revealed that all groups demonstrated similar effects on preventing the down-growth of epithelium and formation of new cementum and new bone. Collagen membranes were tolerated well within the tissues, and membrane remnants were identified at 30 days. In summary, this study indicated that in this dog model similar healing results could be achieved with a bovine type I collagen membrane with or without fibronectin solution and open-flap debridement.

  15. Comparative study of nonabsorbable and absorbable barrier membranes in periodontal osseous defects by guided tissue regeneration

    PubMed Central

    Kaushal, Shalini; Kumar, Avadhesh; Khan, M.A.; Lal, Nand

    2016-01-01

    Background Periodontal invasion of furcation area in multirooted teeth represents one of the most demanding therapeutic challenges in periodontics. Furcation therapy includes various treatment modalities like either maintenance or elimination of furcation or increased access to furcation area. Recent treatment modalities include regenerative procedures like placement of different type of bone grafts with nonabsorbable or absorbable barrier membranes, through guided tissue regeneration. This study compared the clinical efficacy of nonabsorbable barrier membrane with absorbable membrane when used with hydroxyapatite bone graft (G-Graft) in grade II buccal furcation defects in mandibular 1st molars. Materials and methods Fourteen subjects with bilateral grade II buccal furcation defects in lower 1st molars were selected and treated in a split-mouth design. After phase I therapy, molars were divided randomly into two groups for the treatment with either resorbable or nonresorbable membrane in conjunction with G-Graft in both groups. Results All the clinical parameters recorded showed statistically significant improvement in both the groups but no significant difference between two groups was observed. Conclusion Both nonabsorbable and absorbable barrier membranes were equally effective in treating grade II buccal furcation defects in lower molars when used in conjunction with G-Graft except with respect to horizontal bone fill in which absorbable barrier membrane showed better results. PMID:27195208

  16. Fouling propensity and separation efficiency of epoxidated polyethersulfone incorporated cellulose acetate ultrafiltration membrane in the retention of proteins

    NASA Astrophysics Data System (ADS)

    Jayalakshmi, A.; Rajesh, S.; Mohan, D.

    2012-10-01

    Epoxidated polyethersulfone (EPES) incorporated cellulose acetate (CA) ultrafiltration membranes were prepared by diffusion induced precipitation technique in the absence and presence of pore former polyethyleneglycol-600. Effect of blend ratio on the compatibility, thermal stability, mechanical strength, hydrophilicity, morphology, pure water flux, protein adsorption resistance, protein separation efficiency and fouling propensity of the CA/EPES blend membranes was evaluated. Addition of EPES results in the formation of thin separating layer and spongy sub layer in CA/EPES blend membranes. The efficiency of these membranes in the separation of commercially important proteins such as bovine serum albumin, egg albumin, pepsin and trypsin was studied and found to be enhanced as compared to CA membranes. The fouling-resistant capability of the membranes was studied by bovine serum albumin as the model foulant and flux recovery ratio of the membranes were calculated. Attempts have been made to correlate the changes in membrane morphology with pure water flux, hydraulic resistance, thermal and mechanical stability, separation efficiency and antifouling property of the CA/EPES membranes. The optimal combination of CA and EPES, thus allows the preparation of high performance UF membranes which are sufficiently dense to retain proteins and at the same time give economically viable fluxes.

  17. Reconstruction of bone fenestration on mandiblar by the guided bone regeneration methods with beta-TCP/PLGC membranes.

    PubMed

    Koyama, Yoshihisa; Kikuchi, Masanori; Edamura, Kazuya; Nagaoka, Katsuyoshi; Tanaka, Shigeo; Tanaka, Junzo; Takakuda, Kazuo

    2007-03-01

    Guided Bone Regeneration (GBR) is a method for bone tissue regeneration. In this method, membranes are used to cover bone defects and to block the invasion of the surrounding soft tissues. It would provide sufficient time for the osteogenic cells from bone marrow to proliferate and form new bony tissues. In spite of the potential usefulness of this method, no appropriate materials for the GBR membrane have been developed. Here we design the ideal mechanical properties of the GBR membranes and created novel materials, which is the composite of beta-tricalcium phosphate (beta-TCP) and block copolymer of L-lactide, glycolide, and epsilon-caplolactone (PLGC). In the animal experiments with the use of the GBR membranes for large bone defects, we observed significant enhancement in the bone regeneration after 12 weeks implantation and proved the effectiveness of the materials.

  18. Comparable efficacy of silk fibroin with the collagen membranes for guided bone regeneration in rat calvarial defects

    PubMed Central

    Kim, Jwa-Young; Yang, Byoung-Eun; Ahn, Jin-Hee; Park, Sang O

    2014-01-01

    PURPOSE Silk fibroin (SF) is a new degradable barrier membrane for guided bone regeneration (GBR) that can reduce the risk of pathogen transmission and the high costs associated with the use of collagen membranes. This study compared the efficacy of SF membranes on GBR with collagen membranes (Bio-Gide®) using a rat calvarial defect model. MATERIALS AND METHODS Thirty-six male Sprague Dawley rats with two 5 mm-sized circular defects in the calvarial bone were prepared (n=72). The study groups were divided into a control group (no membrane) and two experimental groups (SF membrane and Bio-Gide®). Each group of 24 samples was subdivided at 2, 4, and 8 weeks after implantation. New bone formation was evaluated using microcomputerized tomography and histological examination. RESULTS Bone regeneration was observed in the SF and Bio-Gide®-treated groups to a greater extent than in the control group (mean volume of new bone was 5.49 ± 1.48 mm3 at 8 weeks). There were different patterns of bone regeneration between the SF membrane and the Bio-Gide® samples. However, the absolute volume of new bone in the SF membrane-treated group was not significantly different from that in the collagen membrane-treated group at 8 weeks (8.75 ± 0.80 vs. 8.47 ± 0.75 mm3, respectively, P=.592). CONCLUSION SF membranes successfully enhanced comparable volumes of bone regeneration in calvarial bone defects compared with collagen membranes. Considering the lower cost and lesser risk of infectious transmission from animal tissue, SF membranes are a viable alternative to collagen membranes for GBR. PMID:25551015

  19. Polyanionic collagen membranes for guided tissue regeneration: Effect of progressive glutaraldehyde cross-linking on biocompatibility and degradation.

    PubMed

    Veríssimo, D M; Leitão, R F C; Ribeiro, R A; Figueiró, S D; Sombra, A S B; Góes, J C; Brito, G A C

    2010-10-01

    The ultimate goal of periodontal therapy is to control periodontal tissue inflammation and to produce predictable regeneration of that part of the periodontium which has been lost as a result of periodontal disease. In guided tissue regeneration membranes function as mechanical barriers, excluding the epithelium and gingival corium from the root surface and allowing regeneration by periodontal ligament cells. This report aims to study the effect of glutaraldehyde (GA) cross-linking on mineralized polyanionic collagen (PAC) membranes by conducting a histological evaluation of the tissue response (biocompatibility) and by assessing the biodegradation of subcutaneous membrane implants in rats. We studied six different samples: a PAC, a PAC mineralized by alternate soaking processes for either 25 or 75 cycles (PAC 25 and PAC 75, respectively) and these films cross-linked by GA. Inflammatory infiltrate, cytokine dosage, fibrosis capsule thickness, metalloproteinase immunohistochemistry and membrane biodegradation after 1, 7, 15 and 30 days were measured. The inflammatory response was found to be more intense in membranes without cross-linking, while the fibrosis capsules became thicker in cross-linked membranes after 30 days. The membranes without cross-linking suffered intense biodegradation, while the membranes with cross-linking remained intact after 30 days. The cross-linking with GA reduced the inflammatory response and prevented degradation of the membranes over the entire course of the observation period. These membranes are thus an attractive option when the production of new bone depends on the prolonged presence of a mechanical barrier.

  20. Guided tissue regeneration for using a chitosan membrane: an experimental study in rats.

    PubMed

    Kuo, Shyh Ming; Chang, Shwu Jen; Chen, Ta Wei; Kuan, Tang Ching

    2006-02-01

    Barrier membranes are employed clinically to deflect the growth of gingival tissues away from root surface. They provide an isolated space over the regions with the defective tissues that allow the relatively slow growing periodontal ligament fibroblasts to be repopulated onto the root surface. Several makes of bioabsorbable membranes are now commercially available. In this study, we have employed chitosan as barrier membrane material and evaluated it for a guided tissue regeneration application. Three types of chitosan membranes: Chi-NaOH, Chi-Na(5)P(3)O(10), and Chi-Na(2)SO(3)(each was gelated by NaOH, crosslinked by Na(5)P(3)O(10) and Na(2)SO(3), respectively), were prepared to be evaluated by the following categories: the mechanical strength to create an effective space, the rapid rate to reach hydrolytic equilibrium in phosphate-buffered solution, and the ease of clinical manipulative operations. Consequently, standardized, transosseous and critical sized skull defects were made in adult rats and the defective regions were covered with the specifically prepared chitosan membranes. After 4 weeks of recovering, varying degrees of bone healing were observed beneath the chitosan membranes in comparison to the control group. The chitosan covered regions showed a clear boundary space between connective tissues and bony tissues. Apparently, this process resulted in a good cell occlusion and beneficial osteogenesis effect to the bone. As for the control group, the bone defect was filled with connective tissue, and a destruction of the integrity of newly formed bone was observed. Among the chitosan membranes tested in this study, Chi-NaOH membrane provided a higher percentage of new bone formation than those from the Chi-Na(5)P(3)O(10) and Chi-Na(2)SO(3) families.

  1. Facile fouling resistant surface modification of microfiltration cellulose acetate membranes by using amino acid L-DOPA.

    PubMed

    Azari, Sara; Zou, Linda; Cornelissen, Emile; Mukai, Yasushito

    2013-01-01

    A major obstacle in the widespread application of microfiltration membranes in the wet separation processes such as wastewater treatment is the decline of permeates flux as a result of fouling. This study reports on the surface modification of cellulose acetate (CA) microfiltration membrane with amino acid L-3,4-dihydroxy-phenylalanine (L-DOPA) to improve fouling resistance of the membrane. The membrane surface was characterised using Fourier transform infrared spectroscopy (FTIR), water contact angle and zeta potential measurement. Porosity measurement showed a slight decrease in membrane porosity due to coating. Static adsorption experiments revealed an improved resistance of the modified membranes towards the adhesion of bovine serum albumin (BSA) as the model foulant. Dead end membrane filtration tests exhibited that the fouling resistance of the modified membranes was improved. However, the effect of the modification depended on the foulant solution concentration. It is concluded that L-DOPA modification is a convenient and non-destructive approach to enable low-BSA adhesion surface modification of CA microfiltration membranes. Nevertheless, the extent of fouling resistance improvement depends on the foulant concentration.

  2. A composite membrane based on a biocompatible cellulose as a host of gel polymer electrolyte for lithium ion batteries

    NASA Astrophysics Data System (ADS)

    Xiao, S. Y.; Yang, Y. Q.; Li, M. X.; Wang, F. X.; Chang, Z.; Wu, Y. P.; Liu, X.

    2014-12-01

    A composite polymer membrane is prepared by coating poly(vinylidene fluoride) (PVDF) on the surface of a membrane based on methyl cellulose (MC) which is environmentally friendly and cheap. Its characteristics are investigated by scanning electron microscopy, FT-IR, thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The outer PVDF layers are porous which results in high electrolyte uptake and the lithium ion transference number is much larger than that of the pure MC. Moreover, the cell based on Li//LiFePO4 delivers high discharge capacity and good rate behavior in the range of 4.2-2.5 V when the composite membrane is used as the separator and the host of a gel polymer electrolyte, lithium as the counter and reference electrode, and LiFePO4 as cathode. The obtained results suggest that this unique composite membrane shows great attraction in the lithium ion batteries with high safety and low cost.

  3. Evaluation of an Osseous Allograft Membrane for Guided Tissue Regeneration in the Dog.

    PubMed

    Stepaniuk, Kevin S; Gingerich, Wade

    2015-01-01

    Clinical application of a demineralized freeze-dried cortical bone membrane allograft (DFBMA) for treatment of intra(infra)bony periodontal pockets in dogs was evaluated. The mean pre-treatment periodontal probing depth equaled 7.2-mm. Post-treatment probing depths in all 11 cases were normal, with a mean periodontal probing gain of 5.4-mm. Guided tissue regeneration using a commercially available veterinary canine DFBMA and canine demineralized freeze-dried bone allograft (DFDBA) resulted in clinically significant periodontal attachment gains. The gain of new periodontal tissue attachment was statistically significant (P < 0.0001). The commercially available veterinary allograft products predictably increased new periodontal attachment without any identified membrane sequelae in these 11 cases.

  4. Comparison of polycarbonate and cellulose acetate membrane filters for isolation of Campylobacter concisus from stool samples.

    PubMed

    Nielsen, Hans Linde; Engberg, Jørgen; Ejlertsen, Tove; Nielsen, Henrik

    2013-08-01

    One thousand seven hundred ninety-one diarrheic stool samples were cultivated for Campylobacter spp. We found a high prevalence of Campylobacter concisus with use of a polycarbonate filter (n = 114) compared to a cellulose acetate filter (n = 79) (P < .0001). The polycarbonate filter is superior to the commonly used cellulose acetate filter for detection of C. concisus.

  5. Biosynthesis of callose and cellulose by detergent extracts of tobacco cell membranes and quantification of the polymers synthesized in vitro.

    PubMed

    Cifuentes, Carolina; Bulone, Vincent; Emons, Anne Mie C

    2010-02-01

    The conditions that favor the in vitro synthesis of cellulose from tobacco BY-2 cell extracts were determined. The procedure leading to the highest yield of cellulose consisted of incubating digitonin extracts of membranes from 11-day-old tobacco BY-2 cells in the presence of 1 mM UDP-glucose, 8 mM Ca(2+) and 8 mM Mg(2+). Under these conditions, up to nearly 40% of the polysaccharides synthesized in vitro corresponded to cellulose, the other polymer synthesized being callose. Transmission electron microscopy analysis revealed the occurrence of two types of structures in the synthetic reactions. The first type consisted of small aggregates with a diameter between 3 and 5 nm that associated to form fibrillar strings of a maximum length of 400 nm. These structures were sensitive to the acetic/nitric acid treatment of Updegraff and corresponded to callose. The second type of structures was resistant to the Updegraff reagent and corresponded to straight cellulose microfibrils of 2-3 nm in diameter and 200 nm to up to 5 microm in length. In vitro reactions performed on electron microscopy grids indicated that the minimal rate of microfibril elongation in vitro is 120 nm/min. Measurements of retardance by liquid crystal polarization microscopy as a function of time showed that small groups of microfibrils increased in retardance by up to 0.047 nm/min per pixel, confirming the formation of organized structures.

  6. Performance of cellulose acetate - polyethersulphone blend membrane prepared using microwave heating for palm oil mill effluent treatment.

    PubMed

    Idris, A; Ahmed, I; Jye, H W

    2007-01-01

    The objective of this research is to investigate the performance of blend cellulose acetate (CA)-polyethersulphone (PES) membranes prepared using microwave heating (MWH) techniques and then compare it with blend CA-PES membranes prepared using conventional heating (CH) methods using bovine serum albumin solution. The superior membranes were then used in the treatment of palm oil mill effluent (POME). Various blends of CA-PES have been blended with PES in the range of 1-5 wt%. This distinctive series of dope formulations of blend CA/PES and pure CA was prepared using N, N-dimethylformamide (DMF) as solvent. The dope solution was prepared by MW heating for 5 min at a high pulse and the membranes were prepared by phase inversion method. The performances of these membranes were evaluated in terms of pure water and permeate flux, percentage removal of total suspended solids (TSS), chemical oxygen demand (COD) and biochemical oxygen demand (BOD). The results indicate that blend membranes prepared using the microwave technique is far more superior compared to that prepared using CH. Blend membranes with 19% CA, 1-3% PES and 80% of DMF solvent were found to be the best membrane formulation.

  7. The effect of a bioactive collagen membrane releasing PDGF or GDF-5 on bone regeneration.

    PubMed

    Yamano, Seiichi; Haku, Ken; Yamanaka, Takuto; Dai, Jisen; Takayama, Tadahiro; Shohara, Ryutaro; Tachi, Keita; Ishioka, Mika; Hanatani, Shigeru; Karunagaran, Sanjay; Wada, Keisuke; Moursi, Amr M

    2014-03-01

    Regenerative procedures using barrier membrane technology are presently well established in periodontal/endodontic surgery. The objective of this study was to compare the subsequent effects of the released platelet-derived growth factor (PDGF) and growth/differentiation factor 5 (GDF-5) from collagen membranes (CMs) on bone regeneration in vitro and in vivo. In vitro studies were conducted using MC3T3-E1 mouse preosteoblasts cultured with or without factors. Cell viability, cell proliferation, alkaline phosphatase (ALP) activity and bone marker gene expression were then measured. In vivo studies were conducted by placing CMs with low or high dose PDGF or GDF-5 in rat mandibular defects. At 4 weeks after surgery new bone formation was measured using μCT and histological analysis. The results of in vitro studies showed that CM/GDF-5 significantly increased ALP and cell proliferation activities without cytotoxicity in MC3T3-E1 cells when compared to CM/PDGF or CM alone. Gene expression analysis revealed that Runx2 and Osteocalcin were significantly increased in CM/GDF-5 compared to CM/PDGF or control. Quantitative and qualitative μCT and histological analysis for new bone formation revealed that although CM/PDGF significantly enhanced bone regeneration compared to CM alone or control, CM/GDF-5 significantly accelerated bone regeneration to an even greater extent than CM/PDGF. The results also showed that GDF-5 induced new bone formation in a dose-dependent manner. These results suggest that this strategy, using a CM carrying GDF-5, might lead to an improvement in the current clinical treatment of bone defects for periodontal and implant therapy.

  8. Cellulose nanocrystal-based composite electrolyte with superior dimensional stability for alkaline fuel cell membranes

    DOE PAGES

    Lu, Yuan; Artmentrout, Aaron A.; Li, Juchuan; ...

    2015-01-01

    Cellulose nanocrystal (CNC)-based composite films were prepared as a solid electrolyte for alkaline fuel cells. Poly (vinyl alcohol) (PVA) and silica gel hybrid was used to bind the CNCs to form a robust composite film. The mass ratio (i.e., 1 : 1, 1 : 2) of PVA and silica gel was tuned to control the hydrophobicity of the resulting films. Composite films with a range of CNC content (i.e., 20 to 60%) were prepared to demonstrate the impact of CNC on the performance of these materials as a solid electrolyte for alkaline fuel cells. Different from previously reported cross-linked polymermore » films, CNC-based composite films with 40% hydrophobic binder (i.e., PVA : silica gel=1 : 2) exhibited simultaneous low water swelling (e.g., ~5%) and high water uptake (e.g., ~80%) due to the hydrophilicity and extraordinary dimensional stability of CNC. It also showed a conductivity of 0.044 and 0.065 S/cm at 20 and 60 oC, respectively. To the best of our knowledge, the film with 60% CNC and 40% binder is characterized by the lowest hydroxide conductivity-normalized swelling ratio. Decreased CNC content (i.e., 40 and 20%) resulted in comparable hydroxide conductivity but a greater swelling ratio. These results demonstrate the advantage of CNC as a key component for a solid electrolyte for alkaline fuel cells over conventional polymers, suggesting the great potential of CNCs in improving the dimensional stability while maintaining the conductivity of existing anion exchange membranes.« less

  9. Cellulose nanocrystal-based composite electrolyte with superior dimensional stability for alkaline fuel cell membranes

    SciTech Connect

    Lu, Yuan; Artmentrout, Aaron A.; Li, Juchuan; Tekinalp, Halil L.; Nanda, Jagjit; Ozcan, Soydan

    2015-01-01

    Cellulose nanocrystal (CNC)-based composite films were prepared as a solid electrolyte for alkaline fuel cells. Poly (vinyl alcohol) (PVA) and silica gel hybrid was used to bind the CNCs to form a robust composite film. The mass ratio (i.e., 1 : 1, 1 : 2) of PVA and silica gel was tuned to control the hydrophobicity of the resulting films. Composite films with a range of CNC content (i.e., 20 to 60%) were prepared to demonstrate the impact of CNC on the performance of these materials as a solid electrolyte for alkaline fuel cells. Different from previously reported cross-linked polymer films, CNC-based composite films with 40% hydrophobic binder (i.e., PVA : silica gel=1 : 2) exhibited simultaneous low water swelling (e.g., ~5%) and high water uptake (e.g., ~80%) due to the hydrophilicity and extraordinary dimensional stability of CNC. It also showed a conductivity of 0.044 and 0.065 S/cm at 20 and 60 oC, respectively. To the best of our knowledge, the film with 60% CNC and 40% binder is characterized by the lowest hydroxide conductivity-normalized swelling ratio. Decreased CNC content (i.e., 40 and 20%) resulted in comparable hydroxide conductivity but a greater swelling ratio. These results demonstrate the advantage of CNC as a key component for a solid electrolyte for alkaline fuel cells over conventional polymers, suggesting the great potential of CNCs in improving the dimensional stability while maintaining the conductivity of existing anion exchange membranes.

  10. Hematopoiesis on cellulose ester membranes. XI. Induction of new bone and a hematopoietic microenvironment by matrix factors secreted by marrow stromal cells.

    PubMed

    Knospe, W H; Husseini, S G; Fried, W

    1989-07-01

    Cellulose ester membranes (CEM) were coated with stromal cells from bone marrow (BM) or bone and implanted intraperitoneally (IP) in CAF1 mice for intervals of 1 to 6 months. Previous studies indicated that matrix factors [glycoproteins (GPs), proteoglycans (PGs), and glycosaminoglycans (GAGs)] were secreted by the regenerating stromal cells and adsorbed by the CEM. After 1 to 6 months, the CEMs were removed, scraped free of adherent cells, and irradiated in vitro with 40 Gy. The scraped and irradiated CEMs were then reimplanted IP or subcutaneously (SC) for periods of 1 to 6 months in secondary syngeneic murine hosts. They were then removed for histologic study. CEMs reimplanted in SC sites developed bone and hematopoiesis as early as 1 month after implantation. Maximum hematopoiesis and bone formation was observed after 3 months. CEMs coated during the initial implantation with bone-derived stromal cells contained more bone and hematopoietic cells than did CEMs coated with marrow-derived stromal cells after SC implementation. Neither the CEMs coated with bone stromal cells nor those coated with marrow stromal cells developed new bone or trilineal hematopoiesis after being implanted IP. A few CEMs contained small foci of granulopoiesis only. We conclude that noncellular matrix substances deposited on CEMs by bone, and to a lesser degree by marrow cells, can induce prestromal cells in the SC tissues to produce a microenvironment suitable for trilineal hematopoiesis.

  11. Comparative study of NMP-preloaded and dip-loaded membranes for guided bone regeneration of rabbit cranial defects.

    PubMed

    Karfeld-Sulzer, Lindsay S; Ghayor, Chafik; Siegenthaler, Barbara; Gjoksi, Bebeka; Pohjonen, Timo H; Weber, Franz E

    2017-02-01

    Guided bone regeneration (GBR) has been utilized for several decades for the healing of cranio-maxillofacial bone defects and, particularly in the dental field, by creating space with a barrier membrane to exclude soft tissue and encourage bone growth in the membrane-protected volume. Although the first membranes were non-resorbable, a new generation of GBR membranes aims to biodegrade and provide bioactivity for better overall results. The Inion GTR™ poly(lactide-co-glycolide) (PLGA) membrane is not only resorbable but also bioactive, since it includes N-methylpyrrolidone (NMP), which has been shown to promote bone regeneration. In this study, the effects of loading different amounts of NMP onto the membrane through chemical vapour deposition or dipping have been explored. In vitro release demonstrated that lower levels of NMP led to lower NMP concentrations and slower release, based on total NMP loaded in the membrane. The dipped membrane released almost all of the NMP within 15 min, leading to a high NMP concentration. For the in vivo studies in rabbits, 6 mm calvarial defects were created and left untreated or covered with an ePTFE membrane or PLGA membranes dipped in, or preloaded with, NMP. Evaluation of the bony regeneration revealed that the barrier membranes improved bony healing and that a decrease in NMP content improved the performance. Overall, we have demonstrated the potential of these PLGA membranes with a more favourable NMP release profile and the significance of exploring the effect of NMP on these PLGA membranes with regard to bone ingrowth. Copyright © 2014 John Wiley & Sons, Ltd.

  12. Connective tissue and bacterial deposits on rubber dam sheet and ePTFE barrier membranes in guided periodontal tissue regeneration.

    PubMed

    Apinhasmit, Wandee; Swasdison, Somporn; Tamsailom, Suphot; Suppipat, Nophadol

    2002-01-01

    The aim of this study was to compare the connective tissue and bacterial deposits on rubber dam sheets and expanded polytetrafluoroethylene membranes used as barrier membranes in guided tissue regeneration for periodontal treatment. Twenty patients having intrabony defects and/or furcation defects were surgically treated by guided tissue regeneration employing either rubber dam sheets (10 patients) or expanded polytetrafluoroethylene membranes (10 patients) as barrier membranes. Four to six weeks after the first operation, membranes were retrieved from the lesion sites and processed for scanning electron microscopy. The lesion-facing surfaces of membranes were examined for the presence of connective tissue and bacterial deposits. The differences between the numbers of fields and the distributions of connective tissue and bacteria on both types of membranes were analysed by the Chi-square test at the level of 0.05 significance. The results showed a lot of fibroblasts with their secreted extracellular matrices, known as components of the connective tissue on rubber dam sheets and expanded polytetrafluoroethylene membranes. There was no significant difference in the total number of connective tissue on both types of membranes (P = 0.456). Many bacterial forms including cocci, bacilli, filaments and spirochetes with the interbacterial matrices were identified. The total number of bacteria on rubber dam sheets was statistically less than that on expanded polytetrafluoroethylene membranes (P < 0.001). The comparable number of connective tissue on both types of membranes suggests that the healing process under both types of membranes was also comparable. Therefore, the rubber dam sheet might be used as a barrier membrane in guided tissue regeneration.

  13. In vitro and in vivo evaluation of chitosan/β-glycerol phosphate composite membrane for guided bone regeneration.

    PubMed

    Cui, Jun; Liang, Jie; Wen, Yong; Sun, Xiaoning; Li, Tiejun; Zhang, Gairong; Sun, Kangning; Xu, Xin

    2014-09-01

    Chitosan and β-glycerol phosphate (CS/β-GP) composite, with a thermosensitive sol-gel transition behavior, has been tested as one of the viable materials for barrier membrane fabrication. These studies have provided us with a new concept for a guided bone regeneration (GBR) membrane design. The composition, porous structure of the membrane, and the neutral mild preparation procedures make the CS/β-GP membrane a potentially active guide for bone regeneration. In this study, the CS/β-GP composite membrane, with different concentrations of β-GP, was studied to assess their potential utility in GBR application. The initial attachment of the ST2 stromal cell line to the CS/β-GP composite membrane was better than their attachment to the pure CS membrane. The proliferation and osteoblastic differentiation of the cells were much higher on the CS/β-GP composite membrane as compared to the pure CS membrane (p < 0.05). A mild inflammatory response was observed around the implanted CS/β-GP composite membrane without any foreign body reaction that continued up to 4 weeks of postsurgery. This primary study indicated that the in vitro and in vivo bioactivities of the CS/β-GP composite membrane fulfilled the requirements for GBR technique.

  14. Improved bone regeneration and root coverage using a resorbable membrane with physically assisted cell migration and DFDBA.

    PubMed

    Dodge, J R; Greenwell, H; Drisko, C; Wittwer, J W; Yancey, J; Rebitski, G

    2000-08-01

    Twelve patients with 2 Miller Class I or II buccal recession defects measuring > or = 3.0 mm were treated using the principles of guided tissue regeneration and followed for 12 months. The effectiveness of a polylactide (Guidor) resorbable membrane (GA sites) was compared to a combination treatment of polylactide membrane plus polyglactin root-lining mesh (Vicryl) and demineralized freeze-dried bone allograft (DFDBA) (GVB sites) designed to enhance cell migration and bone regeneration. There was 90% mean soft tissue root coverage for the GVB sites and 78% for the GA sites. The mean osseous dehiscence area coverage with hard tissue was 75% for GVB sites and 30% for GA sites.

  15. Magnetic biodegradable Fe3O4/CS/PVA nanofibrous membranes for bone regeneration.

    PubMed

    Wei, Yan; Zhang, Xuehui; Song, Yu; Han, Bing; Hu, Xiaoyang; Wang, Xinzhi; Lin, Yuanhua; Deng, Xuliang

    2011-10-01

    In recent years, interest in magnetic biomimetic scaffolds for tissue engineering has increased considerably. The aim of this study is to develop magnetic biodegradable fibrous materials with potential use in bone regeneration. Magnetic biodegradable Fe(3)O(4)/chitosan (CS)/poly vinyl alcohol (PVA) nanofibrous membranes were achieved by electrospinning with average fiber diameters ranging from 230 to 380 nm and porosity of 83.9-85.1%. The influences of polymer concentration, applied voltage and Fe(3)O(4) nanoparticles loading on the fabrication of nanofibers were investigated. The polymer concentration of 4.5 wt%, applied voltage of 20 kV and Fe(3)O(4) nanoparticles loading of lower than 5 wt% could produce homogeneous, smooth and continuous Fe(3)O(4)/CS/PVA nanofibrous membranes. X-ray diffraction (XRD) data confirmed that the crystalline structure of the Fe(3)O(4), CS and PVA were maintained during electrospinning process. Fourier transform infrared spectroscopy (FT-IR) demonstrated that the Fe(3)O(4) loading up to 5 wt% did not change the functional groups of CS/PVA greatly. Transmission electron microscopy (TEM) showed islets of Fe(3)O(4) nanoparticles evenly distributed in the fibers. Weak ferrimagnetic behaviors of membranes were revealed by vibrating sample magnetometer (VSM) test. Tensile test exhibited Young's modulus of membranes that were gradually enhanced with the increase of Fe(3)O(4) nanoparticles loading, while ultimate tensile stress and ultimate strain were slightly reduced by Fe(3)O(4) nanoparticles loading of 5%. Additionally, MG63 human osteoblast-like cells were seeded on the magnetic nanofibrous membranes to evaluate their bone biocompatibility. Cell growth dynamics according to MTT assay and scanning electron microscopy (SEM) observation exhibited good cell adhesion and proliferation, suggesting that this magnetic biodegradable Fe(3)O(4)/CS/PVA nanofibrous membranes can be one of promising biomaterials for facilitation of osteogenesis.

  16. Preparation of polyvinylidene fluoride/cellulose acetate blend membrane with polyethylene glycol additive for apple juice clarification

    NASA Astrophysics Data System (ADS)

    Fitri, Shatila Jihadiyah; Widiastuti, Nurul

    2017-03-01

    Polyvinylidene Fluoride (PVDF)/Cellulose Acetate (CA) blend membrane with polyethylene (PEG) addition of casting solution were synthesised to determine its morphology. This purpose of this research is to investigate the effect of PEG addition to membrane performance and its application to the clarification of apple juice. The membranes were prepared from polymer blends of CA and PVDF, dimethyl acetamide (DMAc) as solvent, and PEG as additive. Phase inversion was used to prepare membranes by mixing the polymer blends, solvent and additive to be reacted at temperature 60 °C for 24 hours. The variation of PEG weight percentage were 0, 1 wt%, 3 wt%, and 5 wt%. The addition of PEG increased porosity and fluxes, but decreased membrane rejection. Scanning Electron Microscope (SEM), Atomic Force Microscope (AFM), and Fourier Transform Infrared (FTIR) were applied to evaluate the morphology of membranes, which investigated increasing of pore size, pore distribution, and surface roughness. Apple juice clarification by membrane with 1% PEG was obtained 95,1% clearer than the pure sample.

  17. Organic fouling of thin-film composite polyamide and cellulose triacetate forward osmosis membranes by oppositely charged macromolecules.

    PubMed

    Gu, Yangshuo; Wang, Yi-Ning; Wei, Jing; Tang, Chuyang Y

    2013-04-01

    Fouling of cellulose triacetate (CTA) and thin-film composite (TFC) forward osmosis (FO) membranes by organic macromolecules were studied using oppositely charged lysozyme (LYS) and alginate (ALG) as model foulants. Flux performance and foulant deposition on membranes were systematically investigated for a submerged membrane system. When an initial flux of 25 L/m(2)h was applied, both flux reduction and foulant mass deposition were severe for feed water containing the mixture of LYS and ALG (e.g., 50% LYS and 50% ALG at a total foulant concentration of 100 mg/L). In comparison, fouling was much milder for feed water containing either LYS or ALG alone. Compared to the CTA FO membrane, the TFC FO membrane showed greater fouling propensity under mild FO fouling conditions due to its much rougher surface. Nevertheless, under severe FO fouling conditions, fouling was dominated by foulant-deposited-foulant interaction and membrane surface properties played a less important role. Furthermore, when the feed water contained both LYS and ALG in sufficient amount, the deposited cake layer foulant composition (i.e., the LYS/ALG mass ratio) was not strongly affected by membrane types (CTA versus TFC) nor testing modes (pressure-driven NF mode versus osmosis-driven FO mode). In contrast, solution chemistry such as pH and calcium concentration had remarkable effect on the cake layer composition due to their effects on foulant-foulant interaction.

  18. Composite membrane of bacterially-derived cellulose and molecularly imprinted polymer for use as a transdermal enantioselective controlled-release system of racemic propranolol.

    PubMed

    Bodhibukkana, Chatchada; Srichana, Teerapol; Kaewnopparat, Sanae; Tangthong, Naruedom; Bouking, Pisit; Martin, Gary P; Suedee, Roongnapa

    2006-06-12

    A composite membrane for transdermal delivery of S-propranolol enantiomer was developed based on the controlled pore functionalization of bacterial cellulose membranes using a molecularly imprinted polymer (MIP) layer synthesis. The reactive pore-filling of an asymmetric porous cellulose membrane with a MIP thin-layer was effected using a silanized coupler as an additional anchor for the MIP. MIP thin-layers with specific binding sites for S-propranolol were synthesized by copolymerization of methacrylic acid with a cross-linker, ethylene glycol dimethacrylate in the presence of S-propranolol as the template molecule and the latter was subsequently extracted. Selective transport of S-propranolol through the MIP composite membrane was obtained, although this was determined mostly by the parent cellulose membrane with some ancillary contributory effect from the MIP layer. In addition, an enantioselectivity in the transport of propranolol prodrug enantiomers was found, suggesting that the shape and functional groups orientation, which are similar to that of the print molecule were essential for enantiomeric recognition of the MIP composite membrane. The enantioselectivity of S-MIP membranes was also shown when the release of propranolol enantiomers was studied in vitro using rat skin, with racemic propranolol contained in the donor compartment. The composite membrane of bacterially-derived cellulose and molecularly imprinted polymer may have great potential for use as a transdermal enantioselective controlled-release system for racemic propranolol.

  19. Development of Low Cost Membranes (Ta, Nb & Cellulose Acetate) for H2/CO2 Separation in WGS Reactors

    SciTech Connect

    Seetala, Naidu; Siriwardane, Upali

    2011-12-15

    The main aim of this work is to synthesize low temperature bimetallic nanocatalysts for Water Gas Shift reaction (WGS) for hydrogen production from CO and steam mixture; and develop low-cost metal (Nb/Ta)/ceramic membranes for H2 separation and Cellulose Acetate membranes for CO2 separation. .

  20. Neutralized ion beam modification of cellulose membranes for study of ion charge effect on ion-beam-induced DNA transfer

    NASA Astrophysics Data System (ADS)

    Prakrajang, K.; Sangwijit, K.; Anuntalabhochai, S.; Wanichapichart, P.; Yu, L. D.

    2012-02-01

    Low-energy ion beam biotechnology (IBBT) has recently been rapidly developed worldwide. Ion-beam-induced DNA transfer is one of the important applications of IBBT. However, mechanisms involved in this application are not yet well understood. In this study plasma-neutralized ion beam was applied to investigate ion charge effect on induction of DNA transfer. Argon ion beam at 7.5 keV was neutralized by RF-driven plasma in the beam path and then bombarded cellulose membranes which were used as the mimetic plant cell envelope. Electrical properties such as impedance and capacitance of the membranes were measured after the bombardment. An in vitro experiment on plasmid DNA transfer through the cellulose membrane was followed up. The results showed that the ion charge input played an important role in the impedance and capacitance changes which would affect DNA transfer. Generally speaking, neutral particle beam bombardment of biologic cells was more effective in inducing DNA transfer than charged ion beam bombardment.

  1. [Experimental studies on exterior bFGF for enhancement of membrane guided bone regeneration].

    PubMed

    Duan, Hong; Fan, Yubo; Chen, Jian; Pei, Fuxing; Shen, Bin

    2004-12-01

    These studies sought to evaluate the promoting effect of the exterior bFGF on membrane guided bone regeneration (MGBR). Animal models of MGBR covered with PDLLA membrane tube in bilateral radii were established in 40 New Zealand white rabbits. The membrane tubes on the left side were filled with bFGF 40 microg/100 microl and those on the contralateral side were filled with 100 microl 0.9% NaCl solution as control. The specimens were collected at 2, 4, 8, 12 weeks postoperatively. General observation, X-ray, histological grading and HE staining,and biomechanical examination were applied to studies on the repair of the models of MGBR in the two groups. Two weeks after operation, a sealed room was formed between the two bone fragments where the soft tissues covered the membrane tube. Twelve weeks after operation, PDLLA membrane became fragile and its tube shape was being maintained. Histologically, in the bFGF group numerous newly formed bone trabeculae were seen at 2 weeks after operation the radial defects had healed and the bone reconstruction and remodling had begun by the 12th week. The histological image analysis showed that the values of mean diameter and the area of new bone trabeculae in the bFGF group were higher than those in the control group (P<0.05) at 2 weeks and 4 weeks; however, there were no significant differences in these aspects between the two groups (P>0.05) at 8 and 12 weeks. The strength of the newly formed bone in the bFGF group was higher than that in the control group at 12 weeks postoperatively (P<0.05). Therefore, the authors concluded that bFGF could promote the new bone formation and biomechanical strength in the MGBR model.

  2. Fabrication of tethered carbon nanotubes in cellulose acetate/polyethylene glycol-400 composite membranes for reverse osmosis.

    PubMed

    Sabir, Aneela; Shafiq, Muhammad; Islam, Atif; Sarwar, Afsheen; Dilshad, Muhammad Rizwan; Shafeeq, Amir; Zahid Butt, Muhammad Taqi; Jamil, Tahir

    2015-11-05

    In this study pristine multi-walled carbon nanotubes (MWCNTs) were surface engineered (SE) in strong acidic medium by oxidation purification method to form SE-MWCNT. Five different amount of SE-MWCNT ranging from 0.1 to 0.5 wt% were thoroughly and uniformly dispersed in cellulose acetate/polyethylene glycol (CA/PEG400) polymer matrix during synthesis of membrane by dissolution casting method. The structural analysis, surface morphology and roughness was carried out by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and atomic force microscopy (AFM), respectively, which showed that the dispersed SE-MWCNT was substantially tethered in CA/PEG400 polymer matrix membrane. The thermogravimetric analysis (TGA) of membranes also suggested some improvement in thermal properties with the addition of SE-MWCNT. Finally, the performance of these membranes was assessed for suitability in drinking water treatment. The permeation flux and salt rejection were determined by using indigenously fabricated reverse osmosis pilot plant with 1000 ppm NaCl feed solution. The results showed that the tethered SE-MWCNT/CA/PEG400 polymer matrix membrane, with strong SE-MWCNTs/polymer matrix interaction, improved the salt rejection performance of the membrane with the salt rejection of 99.8% for the highest content of SE-MWCNT.

  3. Development of cellulose acetate propionate membrane for separation of ethanol and ethyl tert-butyl ether mixtures

    SciTech Connect

    Luo, G.S.; Niang, M.; Schaetzel, P.

    1997-04-01

    For pervaporation separation of ethanol and ethyl tert-butyl ether mixtures, a cellulose acetate propionate membrane was chosen as the experimental membrane because of its high selectivity and good mass fluxes. The properties of the membranes were evaluated by the pervaporation separation of mixtures of ethyl tert-butyl ether/ethanol and the sorption experiments. The experimental results showed that the selectivity and the permeates depend on the ethanol concentration in the feed and the experimental temperature. With increases of the ethanol weight fraction in the feed and the temperature, the total and partial mass fluxes increased. With respect to the temperature, ethanol mass flux obeys the Arrhenius equation. The selectivity of this membrane decreases as the temperature and the ethanol concentration in the feed increase. This membrane shows special characteristics at the azeotropic composition. In the vicinity of the azeotropic point, minimum values of ethanol concentration in the permeate and in sorption solution are obtained. The swelling ratios increase when temperature and the ethanol concentration in the feed are increasing. The ethanol concentration in the sorption solution is also influenced by the temperature and the mixture`s composition. When the temperature increases, the sorption selectivity of the membrane decreases.

  4. Recovery of salts from ion-exchange regeneration streams by a coupled nanofiltration-membrane distillation process.

    PubMed

    Jiříček, Tomáš; De Schepper, Wim; Lederer, Tomáš; Cauwenberg, Peter; Genné, Inge

    2015-01-01

    Ion-exchange tap water demineralization for process water preparation results in a saline regeneration wastewater (20-100 mS cm(-1)) that is increasingly problematic in view of discharge. A coupled nanofiltration-membrane distillation (NF-MD) process is evaluated for the recovery of water and sodium chloride from this wastewater. NF-MD treatment of mixed regeneration wastewater is compared to NF-MD treatment of separate anion- and cation-regenerate fractions. NF on mixed regeneration wastewater results in a higher flux (30 L m(-2) h(-1) at 7 bar) compared to NF on the separate fractions (6-9 L m(-2) h(-1) at 30 bar). NF permeate recovery is strongly limited by scaling (50% for separate and 60% for mixed, respectively). Physical signs of scaling were found during MD treatment of the NF permeates but did not result in flux decline for mixed regeneration wastewater. Final salt composition is expected to qualify as a road de-icing salt. NF-MD is an economically viable alternative compared to external disposal of wastewater for larger-scale installations (1.4 versus 2.5 euro m(-3) produced demineralized water for a 10 m3 regenerate per day plant). The cost benefits of water re-use and salt recuperation are small when compared to total treatment costs for mixed regenerate wastewater.

  5. Expression of vascular antigens by bone cells during bone regeneration in a membranous bone distraction system.

    PubMed

    Lewinson, D; Maor, G; Rozen, N; Rabinovich, I; Stahl, S; Rachmiel, A

    2001-11-01

    An in vivo system of membranous bone formation during distraction has been investigated in order to follow cells that express vascular markers with the objective of understanding the neovascularization process. Concomitantly, sustained proliferation of preskeletal cells was achieved through the application of mechanical force. New capillaries and leading edges that arose by angiogenesis from the periosteal and mucosal surfaces and invaded the central zone of the regenerating distraction tissue temporally preceded the growth of delicate woven bone trabeculae from both edges of the cut bone. Concentrically arranged 'onion-like' configurations were abundant in paracentral zones and in association with mesenchymal condensations, suggesting their de novo formation in situ. Vascular specific markers, the angiopoietin receptor Tie-2 and factor VIII-related antigen (FVIIIrAg), were localized immunohistochemically in order to follow cells of vascular origin. Endothelial cells of the new capillaries, centrally located cells of the concentric configurations, pericytes, and most of the adjacent polygonal mesenchymal cells stained positively with specific antibodies to both antigens. Moreover, preosteoblasts and osteoblasts that lie adjacent to or already embedded in the osteiod of the newly formed trabeculae were also FVIIIrAg and Tie-2 immunopositive. As the source of the bone-forming cells in regenerating tissue during distraction is not yet fully understood, this observation might support the possibility of their vascular origin.

  6. Cellulose Nanofibril Based-Aerogel Microreactors: A High Efficiency and Easy Recoverable W/O/W Membrane Separation System

    NASA Astrophysics Data System (ADS)

    Zhang, Fang; Ren, Hao; Dou, Jing; Tong, Guolin; Deng, Yulin

    2017-01-01

    Hereby we report a novel cellulose nanofirbril aerogel-based W/O/W microreactor system that can be used for fast and high efficient molecule or ions extraction and separation. The ultra-light cellulose nanofibril based aerogel microspheres with high porous structure and water storage capacity were prepared. The aerogel microspheres that were saturated with stripping solution were dispersed in an oil phase to form a stable water-in-oil (W/O) suspension. This suspension was then dispersed in large amount of external waste water to form W/O/W microreactor system. Similar to a conventional emulsion liquid membrane (ELM), the molecules or ions in external water can quickly transport to the internal water phase. However, the microreactor is also significantly different from traditional ELM: the water saturated nanocellulose cellulose aerogel microspheres can be easily removed by filtration or centrifugation after extraction reaction. The condensed materials in the filtrated aerogel particles can be squeezed and washed out and aerogel microspheres can be reused. This novel process overcomes the key barrier step of demulsification in traditional ELM process. Our experimental indicates the novel microreactor was able to extract 93% phenol and 82% Cu2+ from external water phase in a few minutes, suggesting its great potential for industrial applications.

  7. Cellulose Nanofibril Based-Aerogel Microreactors: A High Efficiency and Easy Recoverable W/O/W Membrane Separation System.

    PubMed

    Zhang, Fang; Ren, Hao; Dou, Jing; Tong, Guolin; Deng, Yulin

    2017-01-06

    Hereby we report a novel cellulose nanofirbril aerogel-based W/O/W microreactor system that can be used for fast and high efficient molecule or ions extraction and separation. The ultra-light cellulose nanofibril based aerogel microspheres with high porous structure and water storage capacity were prepared. The aerogel microspheres that were saturated with stripping solution were dispersed in an oil phase to form a stable water-in-oil (W/O) suspension. This suspension was then dispersed in large amount of external waste water to form W/O/W microreactor system. Similar to a conventional emulsion liquid membrane (ELM), the molecules or ions in external water can quickly transport to the internal water phase. However, the microreactor is also significantly different from traditional ELM: the water saturated nanocellulose cellulose aerogel microspheres can be easily removed by filtration or centrifugation after extraction reaction. The condensed materials in the filtrated aerogel particles can be squeezed and washed out and aerogel microspheres can be reused. This novel process overcomes the key barrier step of demulsification in traditional ELM process. Our experimental indicates the novel microreactor was able to extract 93% phenol and 82% Cu(2+) from external water phase in a few minutes, suggesting its great potential for industrial applications.

  8. Cellulose Nanofibril Based-Aerogel Microreactors: A High Efficiency and Easy Recoverable W/O/W Membrane Separation System

    PubMed Central

    Zhang, Fang; Ren, Hao; Dou, Jing; Tong, Guolin; Deng, Yulin

    2017-01-01

    Hereby we report a novel cellulose nanofirbril aerogel-based W/O/W microreactor system that can be used for fast and high efficient molecule or ions extraction and separation. The ultra-light cellulose nanofibril based aerogel microspheres with high porous structure and water storage capacity were prepared. The aerogel microspheres that were saturated with stripping solution were dispersed in an oil phase to form a stable water-in-oil (W/O) suspension. This suspension was then dispersed in large amount of external waste water to form W/O/W microreactor system. Similar to a conventional emulsion liquid membrane (ELM), the molecules or ions in external water can quickly transport to the internal water phase. However, the microreactor is also significantly different from traditional ELM: the water saturated nanocellulose cellulose aerogel microspheres can be easily removed by filtration or centrifugation after extraction reaction. The condensed materials in the filtrated aerogel particles can be squeezed and washed out and aerogel microspheres can be reused. This novel process overcomes the key barrier step of demulsification in traditional ELM process. Our experimental indicates the novel microreactor was able to extract 93% phenol and 82% Cu2+ from external water phase in a few minutes, suggesting its great potential for industrial applications. PMID:28059153

  9. Unilateral basement membrane zone alteration of the regenerated laminar region in equine chronic laminitis.

    PubMed

    Kuwano, Atsutoshi; Ueno, Takanori; Katayama, Yoshinari; Nishiyama, Toshio; Arai, Katsuhiko

    2005-07-01

    Between the laminar epidermis and the laminar dermis of laminar region (LR) in equine foot, it can be observed the basement membrane zone (BMZ), which is composed of a basement membrane and its accompaniments like the hemidesmosome and anchoring fibril. Alteration in the BMZ in equine laminitis is possibly related with not only development but also recovery outcome and recurrence of this disease. However, there is little known about the structure of the BMZ during the recovery phase of this disease. To assess the condition of the BMZ of LR affected by chronic laminitis, the tissue was examined in three cases at two weeks, four weeks and three months after the onset of laminitis, using pathological, immunohistochemical and electron microscopic techniques. Histologically in all laminitis cases, there was a regenerated laminar epidermis with proliferating keratinocytes between the Stratum medium and the dermis, but it included the undeveloped secondary epidermal laminae (ud-SELs) structure in one side of the primary epidermal laminae, especially in the part of the deep area of LR. Immunohistochemical results were positive for the anti-type IV collagen, anti-type VII collagen and anti-laminin 5 antibodies in the most BMZs. However, partial BMZs adjacent to the ud-SELs were negative for the anti-type VII collagen and anti-laminin 5 antibodies. Ultrastructurally, in the BMZ of the ud-SEL, the lamina densa and the lamina lucida were present. In contrast, the anchoring fibrils and the hemidesmosomes were either absent, or present at lower than normal levels. In conclusion, the present study indicated that the part of regenerated LR in chronic laminitis was not able to fully restore to construct the BMZ for a long time, especially in the unilateral side of laminar epidermis. It might be related with recurrence of this disease.

  10. Improvement in the long-term stability of an amperometric glucose sensor system by introducing a cellulose membrane of bacterial origin.

    PubMed

    Ammon, H P; Ege, W; Oppermann, M; Gŏpel, W; Eisele, S

    1995-01-15

    Classical amperometric glucose sensors that use cellulose membranes of wood origin (Cuprophan) suffer from the fact that their long-term stability in blood is short; therefore, their clinical use is limited. In the present study, a classical amperometric glucose sensor was covered with a bacterial cellulose (BC) membrane. Its surface in comparison to that of the classical glucose sensor (Cuprophan) and its long-term stability were tested in vitro and in vivo. The surface element composition was approximately 44% oxygen and approximately 56% carbon in both membranes and thus typical for cellulose. BC membranes exhibited fiber structure, whereas cup membranes did not. There was also a qualitative difference in protein adsorption between both membranes on exposure to bovine serum albumin. Treatment with Trogamid of one site of the BC membranes allowed linear glucose detection between 0 and 40 mM. Hemocompatibility of BC membranes was improved in comparison to cup membranes on the basis of complement activation (C3a and C5a). In diluted blood (1:10), the BC-covered sensor exhibited a long-term stability of more than 200 h; in undiluted blood it was stable for about 24 h, which is about 6-7 times longer than the stability of the classical Cup membrane-covered sensor. In in vivo studies, where the BC membrane-covered sensors were connected to the jugular vein of rats, blood glucose levels could be monitored for at least 24 h. In summary, the use of a modified bacterial cellulose membrane to cover the classical amperometric glucose sensor significantly improves the sensor's long-term stability both in vitro and in vivo.

  11. Novel naturally crosslinked electrospun nanofibrous chitosan mats for guided bone regeneration membranes: material characterization and cytocompatibility.

    PubMed

    Norowski, Peter A; Fujiwara, Tomoko; Clem, William C; Adatrow, Pradeep C; Eckstein, Eugene C; Haggard, Warren O; Bumgardner, Joel D

    2015-05-01

    Guided bone regeneration (GBR) barrier membranes are used to prevent soft tissue infiltration into the graft space during dental procedures that involve bone grafting. Chitosan materials have shown promise as GBR barrier membranes, due to their biocompatibility and predictable biodegradability, but degradation rates may still be too high for clinical applications. In this study, chitosan GBR membranes were electrospun using chitosan (70% deacetylated, 312 kDa, 5.5 w/v%), with or without the addition of 5 or 10 mm genipin, a natural crosslinking agent, in order to extend the degradation to meet the clinical target time frame of 4-6 months. Membranes were evaluated for fibre diameter, tensile strength, biodegradation rate, bond structure and cytocompatibility. Genipin addition, at 5 or 10 mm, resulted in median fibre diameters 184, 144 and 154 nm for uncrosslinked, 5 mm and 10 mm crosslinked, respectively. Crosslinking, examined by Fourier transform infrared spectroscopy, showed a decrease in N-H stretch as genipin levels were increased. Genipin-crosslinked mats exhibited only 22% degradation based on mass loss, as compared to 34% for uncrosslinked mats at 16 weeks in vitro. The ultimate tensile strength of the mats was increased by 165% to 32 MPa with 10 mm crosslinking as compared to the uncrosslinked mats. Finally, genipin-crosslinked mats supported the proliferation of SAOS-2 cells in a 5 day growth study, similar to uncrosslinked mats. These results suggest that electrospun chitosan mats may benefit from genipin crosslinking and have the potential to meet clinical degradation time frames for GBR applications.

  12. Nanostructured bacterial cellulose-poly(4-styrene sulfonic acid) composite membranes with high storage modulus and protonic conductivity.

    PubMed

    Gadim, Tiago D O; Figueiredo, Andrea G P R; Rosero-Navarro, Nataly C; Vilela, Carla; Gamelas, José A F; Barros-Timmons, Ana; Neto, Carlos Pascoal; Silvestre, Armando J D; Freire, Carmen S R; Figueiredo, Filipe M L

    2014-05-28

    The present study reports the development of a new generation of bio-based nanocomposite proton exchange membranes based on bacterial cellulose (BC) and poly(4-styrene sulfonic acid) (PSSA), produced by in situ free radical polymerization of sodium 4-styrenesulfonate using poly(ethylene glycol) diacrylate (PEGDA) as cross-linker, followed by conversion of the ensuing polymer into the acidic form. The BC nanofibrilar network endows the composite membranes with excellent mechanical properties at least up to 140 °C, a temperature where either pure PSSA or Nafion are soft, as shown by dynamic mechanical analysis. The large concentration of sulfonic acid groups in PSSA is responsible for the high ionic exchange capacity of the composite membranes, reaching 2.25 mmol g(-1) for a composite with 83 wt % PSSA/PEGDA. The through-plane protonic conductivity of the best membrane is in excess of 0.1 S cm(-1) at 94 °C and 98% relative humidity (RH), decreasing to 0.042 S cm(-1) at 60% RH. These values are comparable or even higher than those of ionomers such as Nafion or polyelectrolytes such as PSSA. This combination of electric and viscoelastic properties with low cost underlines the potential of these nanocomposites as a bio-based alternative to other polymer membranes for application in fuel cells, redox flow batteries, or other devices requiring functional proton conducting elements, such as sensors and actuators.

  13. Presence of interleukin-4-producing cells for human bone regeneration after application of guided tissue regeneration membranes.

    PubMed

    Kabashima, H; Nagata, K

    2001-07-01

    To study the process of bone regeneration we examined three samples of periapical regenerative tissue obtained from two patients under a guided tissue regeneration treatment in endodontic surgery by the immunohistochemical and enzyme histochemical methods. The regenerative tissue consisted of a large number of fibroblast-like cells and a small number of mononuclear cells. Fibroblast-like cells stained positively for alkaline phosphatase and osteopontin, whereas mononuclear cells stained positively for CD4. Interleukin-4-producing cells could be detected in adjacent sections. However, interferon-y-producing cells could not be detected. These findings suggest that interleukin-4-producing cells may be one of the elements associated with success in the human bone regeneration process in vivo.

  14. A method for the identification of sulfated glycopeptide by two-dimensional electrophoresis on cellulose acetate membrane.

    PubMed

    Yokoyama, M; Tanaka, H; Yoshihara, S; Endo, M

    1986-04-01

    Two-dimensional electrophoresis on cellulose acetate membrane permits the clean separation of sulfated glycopeptide in a mixture of acidic glycans (glycosaminoglycans and acidic glycopeptides). Two systems were used. In system 1, 0.1 M pyridine-0.47 M formic acid buffer (pH 3.0) was used in the first and 0.1 M barium acetate (pH 8.0) in the second dimension. In system 2, 0.1 M pyridine-0.47 M formic acid buffer (pH 3.0) was used in the first and 0.1 M HCl in the second dimension. All of the acidic glycans on electrophoretogram were stained with alcian blue in 70% ethanol. On the other hand, sulfated glycans alone were made visible with alcian blue in 0.1 M HCl. Alcian blue in 70% ethanol or 0.1 M HCl, when combined with periodic acid-Schiff's reagent identified sulfated glycopeptides on cellulose acetate membrane.

  15. Effect of Local Sustainable Release of BMP2-VEGF from Nano-Cellulose Loaded in Sponge Biphasic Calcium Phosphate on Bone Regeneration

    PubMed Central

    Sukul, Mousumi; Nguyen, Thuy Ba Linh; Min, Young-Ki; Lee, Sun-Young

    2015-01-01

    Bone regeneration is a coordinated process mainly regulated by multiple growth factors. Vascular endothelial growth factor (VEGF) stimulates angiogenesis and bone morphogenetic proteins (BMPs) induce osteogenesis during bone healing process. The aim of this study was to investigate how these growth factors released locally and sustainably from nano-cellulose (NC) simultaneously effect bone formation. A biphasic calcium phosphate (BCP)-NC-BMP2-VEGF (BNBV) scaffold was fabricated for this purpose. The sponge BCP scaffold was prepared by replica method and then loaded with 0.5% NC containing BMP2-VEGF. Growth factors were released from NC in a sustainable manner from 1 to 30 days. BNBV scaffolds showed higher cell attachment and proliferation behavior than the other scaffolds loaded with single growth factors. Bare BCP scaffolds and BNBV scaffolds seeded with rat bone marrow mesenchymal stem cells were implanted ectopically and orthotopically in nude mice for 4 weeks. No typical bone formation was exhibited in BNBV scaffolds in ectopic sites. BMP2 and VEGF showed positive effects on new bone formation in BNBV scaffolds, with and without seeded stem cells, in the orthotopic defects. This study demonstrated that the BNBV scaffold could be beneficial for improved bone regeneration. Stem cell incorporation into this scaffold could further enhance the bone healing process. PMID:25808925

  16. Colorimetric elastase sensor with peptide conjugated cellulose nanocrystals is interfaced to dialysis membranes

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Clinical detection of human neutrophil elastase (HNE) as point of care biomarker or in situ colorimetric adjuvant to chronic wound dressings presents potential advantages in the management of chronic wounds. A colorimetric approach to the detection of HNE using cotton cellulose nanocrystals (CCN) i...

  17. Combination of Bioactive Polymeric Membranes and Stem Cells for Periodontal Regeneration: In Vitro and In Vivo Analyses

    PubMed Central

    Gonçalves, Flávia; de Moraes, Míriam Santos; Ferreira, Lorraine Braga; Carreira, Ana Cláudia Oliveira; Kossugue, Patrícia Mayumi; Boaro, Letícia Cristina Cidreira; Bentini, Ricardo; Garcia, Célia Regina da Silva; Sogayar, Mari Cleide; Arana-Chavez, Victor Elias; Catalani, Luiz Henrique

    2016-01-01

    Regeneration of periodontal tissues requires a concerted effort to obtain consistent and predictable results in vivo. The aim of the present study was to test a new family of bioactive polymeric membranes in combination with stem cell therapy for periodontal regeneration. In particular, the novel polyester poly(isosorbide succinate-co-L-lactide) (PisPLLA) was compared with poly(L-lactide) (PLLA). Both polymers were combined with collagen (COL), hydroxyapatite (HA) and the growth factor bone morphogenetic protein-7 (BMP7), and their osteoinductive capacity was evaluated via in vitro and in vivo experiments. Membranes composed of PLLA/COL/HA or PisPLLA/COL/HA were able to promote periodontal regeneration and new bone formation in fenestration defects in rat jaws. According to quantitative real-time polymerase chain reaction (qRT-PCR) and Alizarin Red assays, better osteoconductive capacity and increased extracellular mineralization were observed for PLLA/COL/HA, whereas better osteoinductive properties were associated with PisPLLA/COL/HA. We concluded that membranes composed of either PisPLLA/COL/HA or PLLA/COL/HA present promising results in vitro as well as in vivo and that these materials could be potentially applied in periodontal regeneration. PMID:27031990

  18. Combination of Bioactive Polymeric Membranes and Stem Cells for Periodontal Regeneration: In Vitro and In Vivo Analyses.

    PubMed

    Gonçalves, Flávia; de Moraes, Míriam Santos; Ferreira, Lorraine Braga; Carreira, Ana Cláudia Oliveira; Kossugue, Patrícia Mayumi; Boaro, Letícia Cristina Cidreira; Bentini, Ricardo; Garcia, Célia Regina da Silva; Sogayar, Mari Cleide; Arana-Chavez, Victor Elias; Catalani, Luiz Henrique

    2016-01-01

    Regeneration of periodontal tissues requires a concerted effort to obtain consistent and predictable results in vivo. The aim of the present study was to test a new family of bioactive polymeric membranes in combination with stem cell therapy for periodontal regeneration. In particular, the novel polyester poly(isosorbide succinate-co-L-lactide) (PisPLLA) was compared with poly(L-lactide) (PLLA). Both polymers were combined with collagen (COL), hydroxyapatite (HA) and the growth factor bone morphogenetic protein-7 (BMP7), and their osteoinductive capacity was evaluated via in vitro and in vivo experiments. Membranes composed of PLLA/COL/HA or PisPLLA/COL/HA were able to promote periodontal regeneration and new bone formation in fenestration defects in rat jaws. According to quantitative real-time polymerase chain reaction (qRT-PCR) and Alizarin Red assays, better osteoconductive capacity and increased extracellular mineralization were observed for PLLA/COL/HA, whereas better osteoinductive properties were associated with PisPLLA/COL/HA. We concluded that membranes composed of either PisPLLA/COL/HA or PLLA/COL/HA present promising results in vitro as well as in vivo and that these materials could be potentially applied in periodontal regeneration.

  19. Guided bone regeneration utilizing expanded polytetrafluoroethylene membranes in combination with submerged and nonsubmerged dental implants in beagle dogs.

    PubMed

    Fiorellini, J P; Engebretson, S P; Donath, K; Weber, H P

    1998-05-01

    Treatment of partial and total edentulism with submerged and nonsubmerged dental implants which follows the concept of osseointegration has become an accepted treatment modality. With compromised implant sites, practitioners have begun to combine one-stage implants with established techniques including guided bone regeneration. However, the clinical evaluation of this technique is limited. Therefore, the purpose of this study was to evaluate osseointegration and bone regeneration around nonsubmerged or submerged implants placed directly into surgically created osseous defects with or without expanded polytetrafluoroethylene (ePTFE) membranes. A total of 24 implants were placed in the mandibles of 4 beagle dogs and randomly assigned to 1 of 3 treatment groups. In group A, nonsubmerged implants were placed into osseous defects and treated with a poncho style ePTFE membrane. These membranes had a hole punched into the center and were slipped over the nonsubmerged implants. In group B, nonsubmerged implants were placed into osseous defects without an ePTFE membrane. In group C, submerged implants were placed into osseous defects and covered with an ePTFE membrane. Histometric measurements of each treatment group were made to determine percent bone gain or loss along the implant surface. Although a number of membrane removals occurred during the healing period, histological analysis indicated osseous ingrowth and osseointegration around nonsubmerged and submerged implants. An overall comparison of the treatment groups with ANOVA revealed that there were no significant differences between treatment groups, P > or = 0.05. However, when the data were stratified into sites which retained or lost the ePTFE membrane, the percent of bone regeneration was reduced in group A. Therefore, it may be recommended that nonsubmerged implants be placed with a submerged or "semi-submerged" protocol when utilized in conjunction with ePTFE membranes.

  20. Cellulose metabolism in plants.

    PubMed

    Hayashi, Takahisa; Yoshida, Kouki; Park, Yong Woo; Konishi, Teruko; Baba, Kei'ichi

    2005-01-01

    Many bacterial genomes contain a cellulose synthase operon together with a cellulase gene, indicating that cellulase is required for cellulose biosynthesis. In higher plants, there is evidence that cell growth is enhanced by the overexpression of cellulase and prevented by its suppression. Cellulase overexpression could modify cell walls not only by trimming off the paracrystalline sites of cellulose microfibrils, but also by releasing xyloglucan tethers between the microfibrils. Mutants for membrane-anchored cellulase (Korrigan) also show a typical phenotype of prevention of cellulose biosynthesis in tissues. All plant cellulases belong to family 9, which endohydrolyzes cellulose, but are not strong enough to cause the bulk degradation of cellulose microfibrils in a plant body. It is hypothesized that cellulase participates primarily in repairing or arranging cellulose microfibrils during cellulose biosynthesis in plants. A scheme for the roles of plant cellulose and cellulases is proposed.

  1. Cellulose synthase interacting protein: a new factor in cellulose synthesis.

    PubMed

    Gu, Ying; Somerville, Chris

    2010-12-01

    Cellulose is the most abundant biopolymer on earth. The great abundance of cellulose places it at the forefront as a primary source of biomass for renewable biofuels. However, the knowledge of how plant cells make cellulose remains very rudimentary. Cellulose microfibrils are synthesized at the plasma membrane by hexameric protein complexes, also known as cellulose synthase complexes. The only known components of cellulose synthase complexes are cellulose synthase (CESA) proteins until the recent identification of a novel component. CSI1, which encodes CESA interacting protein 1 (CSI1) in Arabidopsis. CSI1, as the first non-CESA proteins associated with cellulose synthase complexes, opens up many opportunities.

  2. Regeneration of chronic tympanic membrane perforation using 3D collagen with topical umbilical cord serum.

    PubMed

    Jang, Chul Ho; Cho, Yong Beom; Yeo, MyungGu; Lee, Hyeongjin; Min, Eun Jung; Lee, Byung Hhwa; Kim, Geun Hyung

    2013-11-01

    Chronic tympanic membrane (TM) perforation is one of the most common otology complications. Current surgical management of TM perforation includes myringoplasty and tympanoplasty. The purpose of this study was to evaluate the efficacy and feasibility of three dimensional (3D) porous collagen scaffolds with topically applied human umbilical cord serum (UCS) for the regeneration of chronic TM perforation in guinea pigs. To achieve this goal, we fabricated porous 3D collagen scaffolds (avg. strut diameter of 236 ± 51 μm, avg. pore size of 382 ± 67 μm, and a porosity of 96%) by using a 3 axis robot dispensing and low temperature plate systems. Guinea pigs were used in a model of chronic TM perforation. In the experimental group (n=10), 3D collagen scaffold was placed on the perforation and topically applied of UCS every other day for a period of 8 days. The control group ears (n=10) were treated with paper discs and phosphate buffered saline (PBS) only using the same regimen. Healing time, acoustic-mechanical properties, and morphological analysis were performed by otoendoscopy, auditory brainstem response (ABR), single-point laser Doppler vibrometer (LDV), optical coherence tomography (OCT), and light microscopic evaluation. The closure of the TM perforation was achieved in 100% of the experimental group vs. 43% of the control group, and this difference was statistically significant (p=0.034). The ABR threshold at all frequencies of the experimental group was significantly recovered to the normal level compared to the control group. TM vibration velocity in the experimental group recovered similar to the normal control level. The difference is very small and they are not statistically significant below 1 kHz (p=0.074). By OCT and light microscopic examination, regenerated TM of the experimental group showed thickened fibrous and mucosal layer. In contrast, the control group showed absence of fibrous layer like a dimeric TM.

  3. [Development and preclinical studies of insulating membranes based on poly-3-hydroxybutyrate-co-3-hydroxyvalerate for guided bone regeneration].

    PubMed

    Ivanov, S Yu; Bonartsev, A P; Gazhva, Yu V; Zharkova, I I; Mukhametshin, R F; Mahina, T K; Myshkina, V L; Bonartseva, G A; Voinova, V V; Andreeva, N V; Akulina, E A; Kharitonova, E S; Shaitan, K V; Muraev, A A

    2015-01-01

    Bone tissue damages are one of the dominant causes of temporary disability and developmental disability. Currently, there are some methods of guided bone regeneration employing different osteoplastic materials and insulation membranes used in surgery. In this study, we have developed a method of preparation of porous membranes from the biopolymer poly-3-hydroxybutyrate-co-3-hydroxyvalerate (PHBV), produced by a strain of Azotobacter chroococcum 7B. The biocompatibility of the porous membranes was investigated in vitro using mesenchymal stem cells (MSCs) and in vivo on laboratory animals. The cytotoxicity test showed the possibility of cell attachment on membrane and histological studies confirmed good insulating properties the material. The data obtained demonstrate the high biocompatibility and the potential application of insulating membranes based on PHBV in bone tissue engineering.

  4. A three-layered nano-carbonated hydroxyapatite/collagen/PLGA composite membrane for guided tissue regeneration.

    PubMed

    Liao, Susan; Wang, Wei; Uo, Motohiro; Ohkawa, Shoji; Akasaka, Tsukasa; Tamura, Kazuchika; Cui, Fuzhai; Watari, Fumio

    2005-12-01

    Functional graded materials (FGM) provided us one new concept for guided tissue regeneration (GTR) membrane design with graded component and graded structure where one face of the membrane is porous thereby allowing cell growth thereon and the opposite face of the membrane is smooth, thereby inhibiting cell adhesion in periodontal therapy. The goal of the present study was to develop a three-layered graded membrane, with one face of 8% nano-carbonated hydroxyapatite/collagen/poly(lactic-co-glycolic acid) (nCHAC/PLGA) porous membrane, the opposite face of pure PLGA non-porous membrane, the middle layer of 4% nCHAC/PLGA as the transition through layer-by-layer casting method. Then the three layers were combined well with each other with flexibility and enough high mechanical strength as membrane because the three layers all contained PLGA polymer that can be easily used for practical medical application. This high biocompatibility and osteoconductivity of this biodegraded composite membrane was enhanced by the nCHAC addition, for the same component and nano-level crystal size with natural bone tissue. The osteoblastic MC3T3-E1 cells were cultured on the three-layered composite membrane, the primary result shows the positive response compared with pure PLGA membrane.

  5. Photo-regenerable multi-walled carbon nanotube membranes for the removal of pharmaceutical micropollutants from water.

    PubMed

    Zaib, Qammer; Mansoor, Bilal; Ahmad, Farrukh

    2013-08-01

    Pharmaceutical micropollutants fall in the category of "emerging contaminants" in water because of their prevalence and persistence in the aqueous environment, and because of a poor understanding of their low-dose exposure effects on human and animal populations. In this study, photo-regenerable multiwalled carbon nanotube membranes with variable water permeabilities were produced by embedding hierarchical TiO2 structures (having porous, spherical morphology) onto a pre-deposited bed of multi-walled carbon nanotubes (MWNTs) using a modified sol-gel technique. These MWNT-TiO2 composites and their constituent materials were characterized by analytical electron microscopy, surface charge measurement, thermogravimetric analysis, and hydrophobicity determination. The adsorption removal potential of MWNT-TiO2 membranes was demonstrated for three representative pharmaceuticals: acetaminophen, carbamazepine and ibuprofen. The peak initial removal percentages of the pharmaceuticals by the MWNT-TiO2 membranes were 80%, 45%, and 24% for carbamazepine, ibuprofen, and acetaminophen, respectively. The ability of the membranes to be regenerated, once they were saturated with the pharmaceutical compounds, was verified by repeating the adsorption removal experiment on the same membranes after exposure to UV light at 254 nm. Peak removal efficiencies after regeneration were 55%, 32%, and 19% for carbamazepine, ibuprofen, and acetaminophen, respectively, indicating some loss in sorptive capacity upon regeneration. Furthermore, the effect of pH on adsorption of ibuprofen, the pharmaceutical that attained the highest mass loading on the sorbent at equilibrium saturation, was studied and its mechanism of adsorption was proposed at pH below pKa.

  6. Water in polymer membranes. 4. Raman scattering from cellulose acetate films

    SciTech Connect

    Scherer, J.R.; Bailey, G.F.; Kint, S.; Young, R.; Malladi, D.P.; Bolton, B.

    1985-01-17

    Raman scattering was observed from thin film optical waveguides of cellulose acetate exposed to water vapor from 0% to 100% relative humidity (RH), and from dilute solutions of water in methyl acetate. Spectra of cellulose acetate (CA398, 39.8% acetyl) at low RH and cellulose triacetate (CTA) at low and high RH are consistent with the presence of water monomers that are weakly hydrogen bonded to acetyl C=O groups. Differences between the spectra of water in CA398 and CTA at low RH are attributed to sequential hydrogen bonding involving OH groups in CA398. At high RH, CA398 and CTA (to a lesser extent) show bands attributed to water/water interactions that are similar to those found in sequentially hydrogen-bonded hydrates. CA398 films that are annealed at high temperatures exhibit decreased water/water interactions at high RH. Exposure of CA398 films to D/sub 2/O converts > 90% of all polymer OH groups to OD groups. This indicates that water is accessible to nearly all regions of the polymer containing OH groups. Annealing does not alter this accessibility but does reduce the total water content by roughly half, at 100% RH. Hydrogen-bonded C=O groups are associated with a band centered at 1731 cm/sup -1/ which increases in intensity with increasing water content in the film but does not shift in frequency. 38 references, 16 figures, 1 table.

  7. Improved drug delivery properties of PVDF membranes functionalized with beta-cyclodextrin--application to guided tissue regeneration in periodontology.

    PubMed

    Boschin, F; Blanchemain, N; Bria, M; Delcourt-Debruyne, E; Morcellet, M; Hildebrand, H F; Martel, B

    2006-10-01

    The purpose of this study was to develop a membrane for guided tissue regeneration applicable in periodontology that could release antimicrobial agent during the healing period. Our strategy consisted to graft beta-cyclodextrin (beta-CD), a molecule that is known to form inclusion complexes with a large variety of drugs, onto PVDF membranes. Grafting occurred by using citric acid that provoked a crosslinking reaction of beta-CD, and the resulting polymer was imprisoned into the porous structure of the PVDF membrane. The reaction produced a weight increase of the membrane, the range of which depended on the temperature and on the time of curing applied in the process. The biological behavior of the membranes evaluated by proliferation and vitality tests showed good proliferation and improved activity of L132 epithelial cells on the raw and on the grafted membranes. Doxycyclin (DOX) and chlorhexidine (CHX) were used as antimicrobial agents. Their inclusion into the beta-CD cavity in aqueous solutions was confirmed by NMR spectroscopy. After the impregnation of the membranes with DOX and CHX, their release was studied in vitro in batch type experiments and measured by UV spectrophotometry. Low amounts of DOX and CHX were delivered from the raw membranes within the first few hours of tests. Grafted membranes, however, delivered DOX and CHX in larger quantities within 24 h and 10 days respectively.

  8. In vitro bioactivity assessment of composite membrane containing antimicrobial lauric acid for guided bone regeneration in dental application

    NASA Astrophysics Data System (ADS)

    Suleiman, Muhammad Jabir; Kalitheertha, Jamuna Thevi; Sabri, Siti Noorzidah

    2015-07-01

    The manuscript reflect research work in fabrication of a triple layered composite membrane and to perform an in vitro bioactivity evaluation on composite membrane containing antimicrobial lauric acid. Poly(lactic-co-glycolic acid) (PLGA) matrix was incorporated with various amounts of nanoapatite (NAp) and lauric acid (LA) to form a triple-layered composite membrane. This membrane was prepared using a single step fabrication technique comprising of solvent casting, thermally induced phase separation and solvent leaching processes. Apatite mineralization was detected on the composite membranes within 30 days of exposure to simulated body fluid (SBF) and showed increased apatite formation at 30-60wt% of NAp content in the PLGA matrix on layer 3 (L3), that has the highest amount of NAp compared with layer 1 (L1) and layer 2 (L2) of the membrane. However, apatite mineralization was not detected on pure PLGA membrane. In addition, incorporation of LA on L1 and L2 has no influence on apatite mineral formation as none detected on these surfaces. The presence of NAp determines the formation of apatite crystals on the composite membrane. These membranes with triple layered design and bioactive properties showed potential use for guided bone regeneration purposes in dental application.

  9. Grafting of cellulose acetate with ionic liquids for biofuel purification by a membrane process: Influence of the cation.

    PubMed

    Hassan Hassan Abdellatif, Faten; Babin, Jérôme; Arnal-Herault, Carole; David, Laurent; Jonquieres, Anne

    2016-08-20

    A new strategy was developed for grafting ionic liquids (ILs) onto cellulose acetate in order to avoid IL extraction and improve its performance for ethyl tert-butyl ether (ETBE) biofuel purification by the pervaporation membrane process. This work extended the scope of IL-containing membranes to the challenging separation of organic liquid mixtures, in which these ILs were soluble. The ILs contained the same bromide anion and different cations with increasing polar feature. The membrane properties were strongly improved by IL grafting. Their analysis in terms of structure-property relationships revealed the influence of the IL content, chemical structure and chemical physical parameters α, β, π* in the Kamlet-Taft polarity scale. The ammonium IL led to the best normalized flux of 0.182kg/m(2)h for a reference thickness of 5μm, a permeate ethanol content of 100% and an outstanding infinite separation factor for the azeotropic mixture EtOH/ETBE at 50°C.

  10. Propylene/propane permeation properties of ethyl cellulose (EC) mixed matrix membranes fabricated by incorporation of nanoporous graphene nanosheets

    PubMed Central

    Yuan, Bingbing; Sun, Haixiang; Wang, Tao; Xu, Yanyan; Li, Peng; Kong, Ying; Niu, Q. Jason

    2016-01-01

    Nanopore containing graphene nanosheets were synthesized by graphene oxide and a reducing agent using a facile hydrothermal treatment in sodium hydroxide media. The as-prepared nanoporous graphene was incorporated into ethyl cellulose (EC) to prepare the mixed matrix membranes (MMMs) for C3H6/C3H8 separation. Transmission electron microscopy (TEM) photograph and X-ray photoelectron spectroscopy (XPS) analysis of nanoporous graphene nanosheets indicated that the structure of nano-pore was irregular and the oxygen-containing groups in the surface were limited. More importantly, the as-prepared MMMs presented better separation performance than that of pristine EC membrane due to simultaneous enhancement of C3H6 permeability and ideal selectivity. The ideal selectivity of the MMMs with 1.125 wt‰ nanoporous graphene content for C3H6/C3H8 increased from 3.45 to 10.42 and the permeability of C3H6 increased from 57.9 Barrer to 89.95 Barrer as compared with the pristine membrane. The presumed facilitated mechanism was that the high specific surface area of nanoporous graphene in polymer matrix increased the length of the tortuous pathway formed by nanopores for the gas diffusion as compared with the pristine graphene nanosheets, and generated a rigidified interface between the EC chains and fillers, thus enhanced the diffusivity selectivity. Therefore, it is expected that nanoporous graphene would be effective material for the C3H6/C3H8 separation. PMID:27352851

  11. [Experimental study of poly-DL-lactic acid membrane guided bone regeneration in rabbit radii bone defects].

    PubMed

    Duan, Hong; Fan, Yubo; Dou, Jun; Pei, Fuxing

    2004-10-01

    This study was conducted to observe bone regeneration guided by poly-DL-latic acid (PDLLA) membrane in rabbit radii bone defects and to explore the mechanism of the membrane guided bone regeneration (MGBR). The animal models of bony and periosteous defects were established in both radii of 40 adult New Zealand white rabbits. The left defect as the experimental side was bridged with PDLLA membrane tube, the right side as the controlled side was untreated. The specimens were collected at 2, 4, 8 and 12 weeks postoperatively. General observation, X-ray, histological observation and biomechanical examination were applied to the repair of the models of MGBR in both groups. Two weeks after operation, with much new bony callus formed outside the tube at both fragments, the membrane tube covered with connective tissues was filled with haematoma and fibrous callus. Twelve weeks after operation, the PDLLA membrane became white and its tube shape was still maintained. However, new bone callus outside the tube almost completely disappeared, and inside the tubes all radii bone defects were successfully repaired with bony union. On the controlled sides, bone defects were filled with connective tissues 2 weeks postoperatively. And 12 weeks after operation, the typical nonunion that had been formed after bone marrow canals were sealed with cortical bone. On the experimental side, the strength of the newly formed bone at the 12th week was higher than that at the 8th week (P<0.05), whereas the biomechanical examination could not be done on the controlled side. Therefore, these findings suggested that the bone regeneration could be successfully guided by PDLLA membrane, and this MGBR technique might be generally used in the treatment of bone defects and nonunion.

  12. Integrated photografted molecularly imprinted polymers with a cellulose acetate membrane for the extraction of melamine from dry milk before HPLC analysis.

    PubMed

    Akbari-Adergani, Behrouz; Sadeghian, Gholam-Hossein; Alimohammadi, Alireza; Esfandiari, Zahra

    2017-03-01

    In this study, a new separation technique based on membrane extraction is described for the determination of melamine in dry milk. The water-compatible cellulose acetate membrane, which is photografted by melamine imprinted nanospheres, was prepared by placing the membrane into the polymerization solution containing methacrylic acid as a functional monomer, ethylene glycol dimethacrylate as cross-linker, acetonitrile as porogen, and melamine as the template molecule. The characterization of the polymeric membrane was performed by Fourier transmission infrared spectroscopy and scanning electron microscopy. This integrated composite membrane was used as a solid-phase extraction medium for the extraction of melamine from dry milk samples. Various parameters affecting the extraction efficiency of the membrane were evaluated. The results showed higher binding capacity for melamine imprinted membranes in comparison with the nonimprinted membranes. High-performance liquid chromatography analysis showed that the extraction of melamine from dry milk by the photografted cellulose acetate membrane had a linear calibration curve in the range of 0.02-11.80 μg/mL with an excellent precision of 2.73%. The limit of detection and quantification of melamine was 0.007 and 0.020 μg/mL, respectively. The recoveries of melamine were in the range of 88.7-94.8%.

  13. Chitosan nanoparticles enhance the antibacterial activity of chlorhexidine in collagen membranes used for periapical guided tissue regeneration.

    PubMed

    Barreras, Uriel Soto; Méndez, Fernando Torres; Martínez, Rita Elizabeth Martínez; Valencia, Carolina Samano; Rodríguez, Panfilo Raymundo Martinez; Rodríguez, Juan Pablo Loyola

    2016-01-01

    Endodontic failure is mainly associated with the persistence of microbial infection in the root canal system and/or the periradicular area. Microorganisms and their toxins located in the root canal system may trigger apical periodontitis and tissue destruction. Tissue regeneration in periapical surgery by using membrane barriers has shown an improved healing and bone closure. However, bacterial membrane contamination is a main reason of failure. In this in vitro study, different brands of chlorhexidine, a combination of chitosan nanoparticles containing chlorhexidine were tested against Enterococcus faecalis on agar plate's cultures and infected collagen membranes. Our results indicated that chitosan nanoparticles acted synergistically with chlorhexidine, inhibiting and eliminating significantly a greater amount of colony former units in both BHI-agar cultures and infected collagen membranes. These results suggested that chitosan nanoparticles could be used to improve regenerative procedures in periapical surgery.

  14. Application of 4-META/MMA-TBB resin for fixation of membrane to tooth in guided tissue regeneration in dog.

    PubMed

    Tomita, Sachiyo; Yamamoto, Shigeki; Shibukawa, Yoshihiro; Kaneko, Tadashi; Miyakoshi, Shoichi; Shimono, Masaki; Yamada, Satoru

    2010-11-01

    The aim of this study was to evaluate 4-META/MMA-TBB resin as an alternative to sling sutures for fixation of membrane to tooth in GTR in terms of its effect on tissue regeneration. Dehiscence periodontal defects were created in 6 dogs which were divided at random into two groups, 3 dogs in each group: an experimental group, in which non-absorbable or absorbable membrane was fixed to the teeth with 4-META/MMA-TBB resin; and a control group, in which sling sutures were applied to fix the two types of membrane. Histologic and histometric evaluation was carried out at 8 weeks post-operatively to determine healing response in each group. Both methods of achieving membrane fixation to tooth were effective in inhibiting epithelial migration and encouraging formation of regenerated periodontal tissues around the root surfaces. These results suggest that 4-META/MMA-TBB resin is as effective as sling sutures in achieving membrane fixation in GTR and is, moreover, easier to apply.

  15. Guided periodontal regeneration using bilayered collagen membranes and bovine bone mineral in fenestration defects in the canine.

    PubMed

    Tal, Haim; Artzi, Zvi; Moses, Ofer; Nemcovsky, Carlos; Kozlovsky, Avital

    2005-10-01

    This study was performed to evaluate the effect of deproteinized bovine porous bone mineral (BBM) and BBM-collagen (BBMC) used alone or in combination with a bilayer collagen membrane in guided periodontal regeneration. In 12 dogs, contralateral surgical circular fenestration defects 5 mm in diameter were produced at the midbuccal aspect of the alveolar bone in 24 maxillary canines. Bone, periodontal ligament, and cementum were completely removed. Experimental sites were filled with BBM or BBMC. Bilayered collagen membranes covered half the experimental sites (BBM+M and BBMC+M), and the other half were left uncovered. Control sites remained empty; half were covered with collagen membranes (cont+M) and the underlying space spontaneously filled with blood, and half were left uncovered (cont). Three months postsurgery, undecalcified sections were prepared. Measurements were made using a caliper on a projection microscope, and the surface area of new bone and BBM particles within the healed surgical defect was evaluated using the point-counting method. In the experimental defects, new cementum covered 31% to 67% of the exposed dentin, with a significant difference between defects covered with membranes and defects that were not covered (P < .05). New cementum in the control (unfilled) defects also differed significantly between covered and uncovered defects. New bone growth presented a pattern similar to the cementum. There was no statistical difference between defects treated with BBM and BBMC, within both covered and uncovered groups. There was less connective tissue in the covered defects than in the uncovered defects (P < .05). The defects were filled with new bone, new connective tissue/bone marrow, and bovine bone particles. New bone area fraction was 23.4% to 25.2% in defects filled with BBMC and BBM, respectively (P = NS). Bone fraction area in membrane-covered defects ranged from 34.4% to 36.8% in experimental defects (P = NS). All membrane-treated defects

  16. Electrically conductive cellulose composite

    DOEpatents

    Evans, Barbara R.; O'Neill, Hugh M.; Woodward, Jonathan

    2010-05-04

    An electrically conductive cellulose composite includes a cellulose matrix and an electrically conductive carbonaceous material incorporated into the cellulose matrix. The electrical conductivity of the cellulose composite is at least 10 .mu.S/cm at 25.degree. C. The composite can be made by incorporating the electrically conductive carbonaceous material into a culture medium with a cellulose-producing organism, such as Gluconoacetobacter hansenii. The composites can be used to form electrodes, such as for use in membrane electrode assemblies for fuel cells.

  17. Use of micro-tomography for validation of method to identify interfacial shear strength from tensile tests of short regenerated cellulose fibre composites

    NASA Astrophysics Data System (ADS)

    Hajlane, A.; Miettinen, A.; Madsen, B.; Beauson, J.; Joffe, R.

    2016-07-01

    The interfacial shear strength of short regenerated cellulose fibre/polylactide composites was characterized by means of an industry-friendly adhesion test method. The interfacial shear strength was back-calculated from the experimental tensile stress-strain curves of composites by using a micro-mechanical model. The parameters characterizing the microstructure of the composites, e.g. fibre length and orientation distributions, used as input in the model were obtained by micro-tomography. The investigation was carried out on composites with untreated and surface treated fibres with various fibre weight contents (5wt%, 10wt%, and 15wt% for untreated fibres, and 15wt% for treated fibres). The properties of fibres were measured by an automated single fibre tensile test method. Based on these results, the efficiency of the fibre treatment to improve fibre/matrix adhesion is evaluated, and the applicability of the method to measure the interfacial shear strength is discussed. The results are compared with data from previous work, and with other results from the literature.

  18. Patterning and Lifetime of Plasma Membrane-Localized Cellulose Synthase Is Dependent on Actin Organization in Arabidopsis Interphase Cells1[W

    PubMed Central

    Sampathkumar, Arun; Gutierrez, Ryan; McFarlane, Heather E.; Bringmann, Martin; Lindeboom, Jelmer; Emons, Anne-Mie; Samuels, Lacey; Ketelaar, Tijs; Ehrhardt, David W.; Persson, Staffan

    2013-01-01

    The actin and microtubule cytoskeletons regulate cell shape across phyla, from bacteria to metazoans. In organisms with cell walls, the wall acts as a primary constraint of shape, and generation of specific cell shape depends on cytoskeletal organization for wall deposition and/or cell expansion. In higher plants, cortical microtubules help to organize cell wall construction by positioning the delivery of cellulose synthase (CesA) complexes and guiding their trajectories to orient newly synthesized cellulose microfibrils. The actin cytoskeleton is required for normal distribution of CesAs to the plasma membrane, but more specific roles for actin in cell wall assembly and organization remain largely elusive. We show that the actin cytoskeleton functions to regulate the CesA delivery rate to, and lifetime of CesAs at, the plasma membrane, which affects cellulose production. Furthermore, quantitative image analyses revealed that actin organization affects CesA tracking behavior at the plasma membrane and that small CesA compartments were associated with the actin cytoskeleton. By contrast, localized insertion of CesAs adjacent to cortical microtubules was not affected by the actin organization. Hence, both actin and microtubule cytoskeletons play important roles in regulating CesA trafficking, cellulose deposition, and organization of cell wall biogenesis. PMID:23606596

  19. Permeation of gas mixtures in cellulose acetate membranes - practical approach to predict the permeation rate CO/sub 2//CH/sub 4/ mixture

    SciTech Connect

    Fouda, A.E.; Matsuura, T.; Lui, A.

    1988-10-01

    Dry cellulose acetate reverse osmosis membranes of different porosities are prepared by using the solvent exchange method and then shrunk at various temperatures. Permeation of single gases and gas mixtures of CO/sub 2/ and CH/sub 4/ through these membranes were investigated at various upstream pressures up to 2.4 MPa. The permeation data of a reference gas usually helium was used to characterize the membrane and determine the flow parameters which can be used to predict the performance of that membrane in separating gas mixtures. The Surface Force - Pore Flow model developed in previous investigations can be used to predict the membrane performance using the above method. The prediction using the characterization parameters of the reference gas proved to be unsatisfactory in most cases, since the surface force is highly dependent on the interaction between the specific gas component in the mixture and the membrane.

  20. Comparison of the performance of natural latex membranes prepared with different procedures and PTFE membrane in guided bone regeneration (GBR) in rabbits.

    PubMed

    Moura, Jonas M L; Ferreira, Juliana F; Marques, Leonardo; Holgado, Leandro; Graeff, Carlos F O; Kinoshita, Angela

    2014-09-01

    This work assessed the performance of membranes made of natural latex extracted from Hevea brasiliensis prepared with three different methods: polymerized immediately after collection without the use of ammonia (L1); polymerized after preservation in ammonia solution (L2); and polymerized after storage in ammonia, followed by Soxhlet technique for the extraction of substances (L3). Polytetrafluoroethylene (PTFE) membrane was used as control. Two 10-mm diameter bone defects were surgically made in the calvaria of thirty adult male New Zealand rabbits. Defects (total n = 60) were treated with guided bone regeneration (GBR) using L1, L2, L3 or PTFE membranes (n = 15 for each membrane). Ten animals were euthanized after 7, 20 and 60 days postoperatively so that five samples (n = 5) of each treatment were collected at each time, and bone regeneration was assessed microscopically. The microscopic analysis revealed defects filled with blood clot and new bone formation at the margins of the defect in all 7-day samples, while 20-day defects were mainly filled with fibrous connective tissue. After 60 days defects covered with L1 membranes showed a significantly larger bone formation area in comparison to the other groups (P < 0.05, ANOVA, Tukey). Additionally, bone tissue hypersensitization for L1 and PTFE membranes was also investigated in six additional rabbits. The animals were subjected to the same surgical procedure for the confection of one 10-mm diameter bone defect that was treated with L1 (n = 3) or PTFE (n = 3). Fifty-three days later, a second surgery was performed to make a second defect, which was treated with the same type of membrane used in the first surgery. Seven days later, the animals were euthanized and samples analyzed. No differences among L1 and PTFE samples collected from sensitized and non-sensitized animals were found (P > 0.05, Kruskal-Wallis). Therefore, the results demonstrated that latex membranes presented performance

  1. Vertical Guided Bone Regeneration using Titanium-reinforced d-PTFE Membrane and Prehydrated Corticocancellous Bone Graft

    PubMed Central

    Cucchi, Alessandro; Ghensi, Paolo

    2014-01-01

    Guided bone regeneration (GBR) standard protocols call for filling the space underneath the membrane with autogenous bone or a mixture composed of autogenous bone particles and allogeneic bone tissue or heterologous biomaterials. This work describes the case of a GBR performed to restore a vertical bone defect with simultaneous placement of a dental implant in the posterior mandible that was carried out using a high density d-PTFE membrane and corticocancellous porcine-derived bone without the addition of any autogenous bone. Bone regeneration was assessed by histological analysis of a biopsy sample collected from the grafted site nine months after the surgery. Intraoral radiographs taken at follow-up visits showed complete maintenance of the peri-implant bone levels for up to two years after prosthesis delivery. The regenerated site successfully supported functional loading of the implant. The present case report suggests that the use of a heterologous bone substitute alone to restore a vertical defect in a GBR procedure can be as effective as the standard protocol, while avoiding the drawbacks associated with a second surgical site opening. PMID:25419250

  2. Utilization of composite membrane polyethyleneglycol-polystyrene-cellulose acetate from pineapple leaf fibers in lowering levels of methyl orange batik waste

    NASA Astrophysics Data System (ADS)

    Delsy, E. V. Y.; Irmanto; Kazanah, F. N.

    2017-02-01

    Pineapple leaves are agricultural waste from the pineapple that the fibers can be utilized as raw material in cellulose acetate membranes. First, made pineapple leaf fibers into pulp and then converted into cellulose acetate by acetylation process in four stages consisting of activation, acetylation, hydrolysis and purification. Cellulose acetate then used as the raw material to manufacture composite membrane with addition of polystyrene and poly (ethylene glycol) as porogen. Composite membrane is made using phase inversion method with dichloromethane-acetone as a solvent. The result of FTIR analysis (Fourier transform infra-red) showed that the absorption of the carbonyl group (C=O) is at 1643.10 cm-1 and acetyl group (C–O ) at 1227.01 cm-1, with a molecular weight of 8.05 x 104 g/mol and the contents (rate) of acetyl is 37.31%. PS-PEG-CA composite membrane had also been characterized by measuring the water flux values and its application to decrease methyl orange content (level) in batik waste. The results showed that the water flux value is of 25.62 L/(m2.hour), and the decrease percentage of methyl orange content in batik waste is 71.53%.

  3. Sorbitol production in charged membrane bioreactor with coenzyme regeneration system: II. Theoretical analysis of a continuous reaction with retained and regenerated NADPH.

    PubMed

    Ikemi, M; Ishimatsu, Y; Kise, S

    1990-06-20

    A theoretical model was constructed in order to study charged membrane bioreactors (CMBRs). In this model, it was postulated that a native nicotinamide coenzyme NADP(H) can be partially retained by a charged membrane in continuous operation. A multienzyme system composed of NADPH-dependent aldose reductase (AR) and glucose dehydrogenase (GDH) was used for the production of sorbitol and gluconic acid from glucose and for the conjugated enzymatic regeneration of NADP(H). Both enzymes were studied with respect to their reaction kinetics. AR was determined to obey the Theorell-Chance mechanism. GDH reaction was approximated by the initial velocity equation of the sequential Bi-Bi mechanism since the reverse reaction could be neglected. Significant inhibitions of both enzymes by sorbitol, gluconic acid, and glucose were observed, and the mode of inhibition was estimated to modify the velocity equations. The differential equation system for each component was derived and numerically analyzed according to the model. The theoretical model elucidated several features of the CMBR. (1) When compared at the same productivity, higher retainment was found to bring about a higher coenzyme turnover number, indicating that the feed coenzyme concentration can be reduced. (2) Under constant conversion, a contradictory relationship between turnover number and residence time arises if the feed concentration of a coenzyme varies. The theoretical model predicts that there is a practically optimal concentration for using NADP(H) efficiently. This concentration was consistent with that yielding the estimated minimum total cost. (3) In this system, excess-GDH-to-AR activity was required because of differences in their kinetic constants. The amount of regeneration enzyme required can be reduced by the accumulation of excels NADPH due to coenzyme retainment. (4) Comparison with an ideal repeated batch reaction revealed that the continuously operated CMBR was vastly superior with respect to

  4. S-propranolol imprinted polymer nanoparticle-on-microsphere composite porous cellulose membrane for the enantioselectively controlled delivery of racemic propranolol.

    PubMed

    Jantarat, Chutima; Tangthong, Naruedom; Songkro, Sarunyoo; Martin, Gary P; Suedee, Roongnapa

    2008-02-12

    Molecularly imprinted polymer (MIP) nanoparticle-on-microspheres (NOM) selective for S-propranolol were successfully prepared using suspension polymerization involving agitation of the reaction mixture at high speed. The integration of the MIP-NOM into a self-assembled porous cellulose membrane allowed a controlled distribution and availability of the molecule recognition sites within a porous structure. The nature of the membrane-included microparticles determined the degree of porosity whilst the adherent nanoparticles provided an increased surface area enabling the composite membrane to be employed efficiently for the trans-membrane transport of the imprinted molecule. The MIP-NOM within the membrane were easily accessible for binding of the imprinted molecule and appeared to maintain high selectivity, indicating that the composite membranes may potentially provide valuable affinity matrices. In this study, the application for MIP-NOM composite cellulose membranes were investigated for their potential to act as transdermal drug delivery systems for the S-enantiomers from racemic propranolol, its ester prodrugs (cyclopropanoyl- and valeryl-propranolol) or other beta-blockers (pindolol and oxprenolol). The enantioselective release of the fluorescently active 1-pyrene-butyryl ester prodrug of S-propranolol from MIP-NOM composite membranes and its diffusion and transit across excised rat skin was monitored by confocal laser scanning microscopy. The mechanism underlying the release of S-propranolol from the MIP-NOM composite membrane was found to involve specific adsorption and mobility of this enantiomer at the binding site in the MIP-NOM as the latter undergo a transition from the dry to wet state. The proposed MIP-NOM composite membrane controlled release system may be applicable for fabrication of novel membranes with self-controllable permeability responding to the presence of target solutes.

  5. Treatment of an early failing implant by guided bone regeneration using resorbable collagen membrane and bioactive glass

    PubMed Central

    Talreja, Prakash S.; Gayathri, G. V.; Mehta, D. S.

    2013-01-01

    Implant failure can be divided into early (prior to prosthetic treatment) or late (after prosthetic rehabilitation). Early failure is generally due to interference in the healing process after implant placement. Implants undergoing early failure will show progressive bone loss on radiographs during the healing period (4 to 6 weeks). In the present case report, early progressive bone loss was seen at 6 weeks, after placement of a non-submerged single piece mini implant. Clinical examination revealed peri-implant bleeding on probing and pocket and grade-1 mobility. Treatment protocol included mechanical debridement (plastic curettes), chemical detoxification with supersaturated solution of citric acid, antibiotics and guided bone regeneration therapy using the collagen membrane as guided bone regeneration barrier in combination with bioactive glass as bone grafting material. The 6 month postoperative examination showed complete resolution of the osseous defect, thus suggesting that this technique may hold promise in the treatment of implants undergoing early failure. PMID:23633789

  6. Efficient performance and the microbial community changes of submerged anaerobic membrane bioreactor in treatment of sewage containing cellulose suspended solid at 25°C.

    PubMed

    Watanabe, Ryoya; Nie, Yulun; Takahashi, Shintaro; Wakahara, Shinichiro; Li, Yu-You

    2016-09-01

    Influence of cellulose as suspended solid (SS) on the performance of submerged anaerobic membrane bioreactor (SAnMBR) was evaluated at 25°C using two types of synthetic sewage (SS contained or not). During the 110days operation, COD and BOD removal, CH4 gas recovery and cellulose accumulation were investigated in detail. The influence of cellulose as SS in sewage on the SAnMBR performance was not significant at HRT longer than12h and 65-72% of the influent COD was recovered as methane gas at HRT of 12h. At HRT of 6h, the quality of effluent got worse and the accumulation of cellulose was found in reactor. 16S rRNA analysis revealed that the microbial diversity distribution including Archaea and Bacteria changed due to the addition of SS in sewage and specific microbe for cellulose degradation such as Proteobacteria was detected. Sludge in SAnMBR could acclimate to characteristics of sewage by self-adaptation.

  7. Comparison of clinical outcomes following guided tissue regeneration treatment with a polylactic acid barrier or a collagen membrane.

    PubMed

    Wu, Shih-Yun; Chen, Yen-Ting; Chen, Chi-Wei; Chi, Lin-Yang; Hsu, Nai-Ying; Hung, Shan-Ling; Ling, Li-Jane

    2010-04-01

    This prospective, randomized, controlled clinical trial compared the clinical outcomes for a polylactic acid barrier versus a collagen membrane in conjunction with guided tissue regeneration (GTR). Thirty patients with chronic periodontitis and at least one intrabony defect of a minimum 4 mm were enrolled. Following full-mouth scaling, GTR using a collagen membrane or a polylactic acid barrier was performed at one site in each patient. At 1 week before and 6 months after surgery, probing pocket depth (PPD), clinical attachment level (CAL), marginal tissue recession, and bone fill were assessed. A significant reduction in PPD (2.50 +/- 1.35 mm for the polylactic acid barrier and 2.60 +/- 1.08 mm for the collagen membrane) was obtained, in addition to gains in CAL (2.40 +/- 1.17 mm for the polylactic acid barrier and 2.60 +/- 1.26 mm for the collagen membrane) and bone fill (0.33 +/- 1.89 mm for polylactic acid barrier and 2.57 +/- 1.64 mm for collagen membrane), for each group compared to baseline. Significantly, the results from 6 months after surgery showed that there was greater bone fill when the collagen membrane was used compared to the polylactic acid barrier.

  8. The regeneration and recycle of chromium etching solutions using concentrator cell membrane technology.

    PubMed

    Chaudhary, Abdul J; Ganguli, Bijita; Grimes, Susan M

    2006-02-01

    The regeneration of chromium (VI) and the recovery of etched copper from chromium etching solutions by electrodialysis is improved by the addition of a concentrator cell in the catholyte chamber. The concentrator media used are ion-exchange resins or activated carbon cloth. The maximum percentages for the regeneration of chromium and recovery of copper in these systems is however less than 80% and 90% respectively because of the competition between the processes of oxidation of Cr(III) and electrodeposition of copper. A novel combination of electrolysis with electrodialysis and concentrator cell technology is developed that achieves 92% chromium regeneration and 90% copper recovery.

  9. Surface modification of TiO2 nanoparticles with biodegradable nanocellolose and synthesis of novel polyimide/cellulose/TiO2 membrane.

    PubMed

    Ahmadizadegan, Hashem

    2017-04-01

    In this paper, novel polyimide/cellulose/TiO2 bionanocomposites (PI/BNCs) were prepared via a simple and inexpensive ultrasonic irradiation process. PI was synthesized by direct polycondensation reaction of novel monomer dianhydride with 4-(2-(4-aminophenyl)-1,1,1,3,3,3-hexafluoropropan-2-yl)benzenamine. Due to the high surface energy and tendency for agglomeration the surface of nanoparticles was modified with cellulose. PI/BNCs containing 5, 10, and 15% of cellulose/TiO2 (BNCs) were successfully fabricated through ultrasonic irradiation technique. The obtained PI/BNCs were characterized by Fourier transform-infrared (FT-IR) spectroscopy, thermogravimetry analysis, X-ray powder diffraction, field emission-scanning electron microscopy (FE-SEM), and transmission electron microscopy (TEM). Thermogravimetric analysis data indicated an increase thermal stability of the PI/BNC polymers in compared to the pure polymer. From TEM image of PI/BNCs it can be found that the surface modified TiO2 with diametric size of less than 50nm, uniformly dispersed in the obtained PI matrix. The results obtained from gas permeation experiments with a constant pressure setup indicated that adding cellulose/TiO2 to the polymeric membrane structure increased the permeability of the membranes.

  10. Efficacy of Natural and Allopathic Antimicrobial Agents Incorporated onto Guided Tissue Regeneration Membrane Against Periodontal Pathogens: An in vitro Study

    PubMed Central

    Reddy Palle, Ajay; Kumar Gedela, Rajani; Vasudevan, Sanjay

    2017-01-01

    Introduction Periodontal disease is one of the most prevalent afflictions worldwide. It is an infection of the periodontium as a result of subgingival colonization of the specific microbiota, leading to loss of attachment, which requires optimal care for regeneration to its pre-disease state. Guided Tissue Regeneration (GTR) is one of the successful treatment modalities in Periodontal Regenerative Therapy, but is vulnerable to bacterial colonization. The conflict between usage of classical antibiotics and plant origin antimicrobial agents has recently been in the limelight. Aim The aim of this study was to assess the in vitro antimicrobial activity of amoxicillin, metronidazole and green coffee extract loaded onto GTR membrane against periodonto-pathogens. Materials and Methods Pure form of amoxicillin, metronidazole and green coffee extract were obtained. One percent concentration of each antimicrobial agent was prepared by appropriate dilution with distilled water. GTR membrane was cut into a size of 1x0.5 cm under sterile conditions and was coated with the antimicrobial agents respectively and with distilled water as the negative control. Antimicrobial activity was checked against Aggregatibacter actinomycetemcomitans (A. actinomycetemcomitans) and Porphyromonas gingivalis (P. gingivalis) using agar disc diffusion method. The statistical analysis was done using Kruskal Wallis ANOVA and Mann-Whitney U test. Results One percent amoxicillin showed level of significance (p>0.05) against both A. actinomycetemcomitans and P. gingivalis. Green coffee extract showed no zone of inhibition against both the bacterial species. Conclusion Loading of commercially available antimicrobial agents onto GTR membrane can prevent its bacterial colonization leading to better treatment outcomes for periodontal regeneration. PMID:28274052

  11. Antibacterial efficacy of triple-layered poly(lactic-co-glycolic acid)/nanoapatite/lauric acid guided bone regeneration membrane on periodontal bacteria.

    PubMed

    Saarani, Nur Najiha; Jamuna-Thevi, Kalitheerta; Shahab, Neelam; Hermawan, Hendra; Saidin, Syafiqah

    2017-01-20

    A guided bone regeneration (GBR) membrane has been extensively used in the repair and regeneration of damaged periodontal tissues. One of the main challenges of GBR restoration is bacterial colonization on the membrane, constitutes to premature membrane degradation. Therefore, the purpose of this study was to investigate the antibacterial efficacy of triple-layered GBR membrane composed of poly(lactic-co-glycolic acid) (PLGA), nanoapatite (NAp) and lauric acid (LA) with two types of Gram-negative periodontal bacteria, Fusobacterium nucleatum and Porphyromonas gingivalis through a disc diffusion and bacterial count tests. The membranes exhibited a pattern of growth inhibition and killing effect against both bacteria. The increase in LA concentration tended to increase the bactericidal activities which indicated by higher diameter of inhibition zone and higher antibacterial percentage. It is shown that the incorporation of LA into the GBR membrane has retarded the growth and proliferation of Gram-negative periodontal bacteria for the treatment of periodontal disease.

  12. Layer-by-layer paper-stacking nanofibrous membranes to deliver adipose-derived stem cells for bone regeneration.

    PubMed

    Wan, Wenbing; Zhang, Shiwen; Ge, Liangpeng; Li, Qingtao; Fang, Xingxing; Yuan, Quan; Zhong, Wen; Ouyang, Jun; Xing, Malcolm

    2015-01-01

    Bone tissue engineering through seeding of stem cells in three-dimensional scaffolds has greatly improved bone regeneration technology, which historically has been a constant challenge. In this study, we researched the use of adipose-derived stem cell (ADSC)-laden layer-by-layer paper-stacking polycaprolactone/gelatin electrospinning nanofibrous membranes for bone regeneration. Using this novel paper-stacking method makes oxygen distribution, nutrition, and waste transportation work more efficiently. ADSCs can also secrete multiple growth factors required for osteogenesis. After the characterization of ADSC surface markers CD29, CD90, and CD49d using flow cytometry, we seeded ADSCs on the membranes and found cells differentiated, with significant expression of the osteogenic-related proteins osteopontin, osteocalcin, and osteoprotegerin. During 4 weeks in vitro, the ADSCs cultured on the paper-stacking membranes in the osteogenic medium exhibited the highest osteogenic-related gene expressions. In vivo, the paper-stacking scaffolds were implanted into the rat calvarial defects (5 mm diameter, one defect per parietal bone) for 12 weeks. Investigating with microcomputer tomography, the ADSC-laden paper-stacking membranes showed the most significant bone reconstruction, and from a morphological perspective, this group occupied 90% of the surface area of the defect, produced the highest bone regeneration volume, and showed the highest bone mineral density of 823.06 mg/cm(3). From hematoxylin and eosin and Masson staining, the new bone tissue was most evident in the ADSC-laden scaffold group. Using quantitative polymerase chain reaction analysis from collected tissues, we found that the ADSC-laden paper-stacking membrane group presented the highest osteogenic-related gene expressions of osteocalcin, osteopontin, osteoprotegerin, bone sialoprotein, runt-related transcription factor 2, and osterix (two to three times higher than the control group, and 1.5 times higher

  13. Recovery of valuable soluble compounds from washing waters generated during small fatty pelagic surimi processing by membrane processes.

    PubMed

    Dumay, J; Radier, S; Barnathan, G; Bergé, J P; Jaouen, P

    2008-04-01

    This work focuses on the treatment of washing waters coming from surimi manufacturing using ultrafiltration technology at a laboratory scale. Four membrane materials (poly-ether sulfone, polyacrilonytrile, poly vinylidene fluoride and regenerated cellulose) and 5 Molecular Weight Cut-Off (from 3 to 100 kDa) have been studied at bench laboratory scale using the pilot Rayflow 100, commercialised by Rhodia Orelis. The investigation deals with the ability for membranes to offer a high retention of biochemical compounds (proteins and lipids). Results obtained during adsorption tests showed that the regenerated cellulose material seems to be the most appropriate with regards to pore size reduction due to the protein-adsorption. During the ultrafiltration of the washing water, the regenerated cellulose material leads to the best results, followed by the polyacrylonitrile and poly-vinylidene fluoride materials. Poor results were obtained with polyether sulfone membrane. Compared to the other materials, the regenerated cellulose is the easiest to regenerate, with minimal cleaning water and no chemical treatment necessary. Biochemical characterization of the fractions generated during the ultrafiltration with the polyacrilonytrile, poly vinylidene fluoride and regenerated cellulose membranes showed that all the membranes provided a high recovery rate of the lipids and proteins. The 10 kDa regenerated cellulose membrane had the highest performance and was further evaluated. With such a treatment, the chemical oxygen demand was reduced by 75%. By performing hydrolysis followed by a centrifugation, biochemical composition of the sludge and liquid fraction were modified, producing an insoluble fraction containing fats and few proteins and a soluble fraction containing proteins and few fats. The sludge, initially insoluble, was mainly solubilized during hydrolysis, and lipids and peptides were concentrated by ultrafiltration.

  14. The rice dynamin-related protein DRP2B mediates membrane trafficking, and thereby plays a critical role in secondary cell wall cellulose biosynthesis.

    PubMed

    Xiong, Guangyan; Li, Rui; Qian, Qian; Song, Xueqin; Liu, Xiangling; Yu, Yanchun; Zeng, Dali; Wan, Jianmin; Li, Jiayang; Zhou, Yihua

    2010-10-01

    Membrane trafficking between the plasma membrane (PM) and intracellular compartments is an important process that regulates the deposition and metabolism of cell wall polysaccharides. Dynamin-related proteins (DRPs), which function in membrane tubulation and vesiculation are closely associated with cell wall biogenesis. However, the molecular mechanisms by which DRPs participate in cell wall formation are poorly understood. Here, we report the functional characterization of Brittle Culm3 (BC3), a gene encoding OsDRP2B. Consistent with the expression of BC3 in mechanical tissues, the bc3 mutation reduces mechanical strength, which results from decreased cellulose content and altered secondary wall structure. OsDRP2B, one of three members of the DRP2 subfamily in rice (Oryza sativa L.), was identified as an authentic membrane-associated dynamin via in vitro biochemical analyses. Subcellular localization of fluorescence-tagged OsDRP2B and several compartment markers in protoplast cells showed that this protein not only lies at the PM and the clathrin-mediated vesicles, but also is targeted to the trans-Golgi network (TGN). An FM4-64 uptake assay in transgenic plants that express green fluorescent protein-tagged OsDRP2B verified its involvement in an endocytic pathway. BC3 mutation and overexpression altered the abundance of cellulose synthase catalytic subunit 4 (OsCESA4) in the PM and in the endomembrane systems. All of these findings lead us to conclude that OsDRP2B participates in the endocytic pathway, probably as well as in post-Golgi membrane trafficking. Mutation of OsDRP2B disturbs the membrane trafficking that is essential for normal cellulose biosynthesis of the secondary cell wall, thereby leading to inferior mechanical properties in rice plants.

  15. Inkjet printing of nanoporous gold electrode arrays on cellulose membranes for high-sensitive paper-like electrochemical oxygen sensors using ionic liquid electrolytes.

    PubMed

    Hu, Chengguo; Bai, Xiaoyun; Wang, Yingkai; Jin, Wei; Zhang, Xuan; Hu, Shengshui

    2012-04-17

    A simple approach to the mass production of nanoporous gold electrode arrays on cellulose membranes for electrochemical sensing of oxygen using ionic liquid (IL) electrolytes was established. The approach, combining the inkjet printing of gold nanoparticle (GNP) patterns with the self-catalytic growth of these patterns into conducting layers, can fabricate hundreds of self-designed gold arrays on cellulose membranes within several hours using an inexpensive inkjet printer. The resulting paper-based gold electrode arrays (PGEAs) had several unique properties as thin-film sensor platforms, including good conductivity, excellent flexibility, high integration, and low cost. The porous nature of PGEAs also allowed the addition of electrolytes from the back cellulose membrane side and controllably produced large three-phase electrolyte/electrode/gas interfaces at the front electrode side. A novel paper-based solid-state electrochemical oxygen (O(2)) sensor was therefore developed using an IL electrolyte, 1-butyl-3-methylimidazolium hexafluorophosphate (BMIMPF(6)). The sensor looked like a piece of paper but possessed high sensitivity for O(2) in a linear range from 0.054 to 0.177 v/v %, along with a low detection limit of 0.0075% and a short response time of less than 10 s, foreseeing its promising applications in developing cost-effective and environment-friendly paper-based electrochemical gas sensors.

  16. Fate and impact of organics in an immersed membrane bioreactor applied to brine denitrification and ion exchange regeneration.

    PubMed

    McAdam, Ewan J; Pawlett, Mark; Judd, Simon J

    2010-01-01

    The application of membrane bioreactors (MBRs) to brine denitrification for ion exchange regeneration has been studied. The developed culture was capable of complete brine denitrification at 50 gNaCl.l(-1). Denitrification reduced to c.60% and c.70% when salinity was respectively increased to 75 and 100g.l(-1), presumed to be due to reduced growth rate and the low imposed solids retention time (10 days). Polysaccharide secretion was not induced by stressed cells following salt shocking, implying that cell lysis did not occur. Fouling propensity, monitored by critical flux, was steady at 12-15l.m(-2).h(-1) during salinity shocking and after brine recirculation, indicating that the system was stable following perturbation. Low molecular weight polysaccharide physically adsorbed onto the nitrate selective anion exchange resin during regeneration reducing exchange capacity by c.6.5% when operating up to complete exhaustion. However, based on a breakthrough threshold of 10 mgNO(3)(-)-N.l(-1) the exchange capacity was comparative to that determined when using freshly produced brine for regeneration. It was concluded that a denitrification MBR was an appropriate technology for IEX spent brine recovery and reuse.

  17. Which glycosaminoglycans are suitable for antithrombogenic or athrombogenic coatings of biomaterials? Part I: Basic concepts of immobilized GAGs on partially cationized cellulose membrane.

    PubMed

    Baumann, H; Mueller, U; Keller, R

    1997-01-01

    Six different GAGs of different natural origin such as unfractionated heparin (HE), chondroitin sulfate (CS), dermatan sulfate (DS), keratan sulfate (KS), endothelial cell surface heparan sulfate (ESHS), and hyaluronan (HA) have been ionically immobilized onto partially cationized cellulose membranes with a substitution degree of 0.06. The GAGs have been characterized in terms of total sulfate content and relative molecular weight. The amount of immobilized GAGs was 10(3) times higher than the theoretical amount for monomolecular side-to-side coordination on polymer surfaces. In a standardized perfusion system with shear rates of 1050 sec-1, 37 degrees C, and 5 minutes with citrated blood, the level of platelet adhesion was 100% for partially cationized membrane, 90% for HA, 75% for each HE, CS, DS, KS, 5% for unmodified cellulose membrane, and 5% for confluent bovine aorta endothelial cells, referred to subendothelial matrix as standard for 100% platelet adhesion. ESHS-coated membranes were completely inert to platelets. The amount of ionically released GAGs during perfusion was also estimated. The partial cationic membrane is a suitable polymer surface in combination with the perfusion system to estimate the hemocompatibility of ionically immobilized water-soluble polyanions in terms of platelet adhesion at defined shear rates. The results of platelet adhesion are discussed in terms of structure and analytical parameter of the immobilized GAGs.

  18. A comparative study of combined treatment with a collagen membrane and enamel matrix proteins for the regeneration of intraosseous defects.

    PubMed

    Minabe, Masato; Kodama, Toshiro; Kogou, Tatsuji; Takeuchi, Kayo; Fushimi, Hajime; Sugiyama, Takashi; Mitarai, Eiko

    2002-12-01

    Recent clinical study shows that periodontal regeneration therapy using enamel matrix proteins (Emdogain; EMD) is expected to have the same therapeutic effect as guided tissue regeneration (GTR). However, reports on the combined effect of both therapies are limited, and the clinical significance is not definite. In this study, clinical effects were studied by comparing a combination of EMD and GTR using a collagen membrane for intrabony defects with GTR monotherapy and EMD monotherapy. Sixty-one patients with 69 intrabony defects were included. Efficacy of treatment was evaluated at 6 months and 1 year by assessment of reduction of probing depth, probing attachment gain, and radiographic bone gain. There were no statistically significant differences between presurgical soft tissue measurements and defect characteristics for the three treatment groups. The results showed no significant differences in reduction of probing depth, probing attachment gain, or radiographic bone gain between the three treatment groups at both evaluation times. The combination of GTR using a resorbable membrane for intrabony defects and EMD did not enhance the therapeutic effect compared with each monotherapy.

  19. Comparative study of two collagen membranes for guided tissue regeneration therapy in periodontal intrabony defects: a randomized clinical trial

    PubMed Central

    2014-01-01

    Purpose The purpose of this study was to assess and compare the clinical and radiographic outcomes of guided tissue regeneration therapy for human periodontal intrabony defects using two different collagen membranes: a porous nonchemical cross-linking collagen membrane (NC) and a bilayer collagen membrane (BC). Methods Thirty subjects were randomly assigned and divided into the following 3 groups: a test group (NC+BM), in which a NC was used with xenograft bone mineral (BM), a positive control group (BC+BM), in which a BC was used with xenograft BM, and a negative control group (BM), in which only xenograft BM was used. The following clinical measurements were taken at baseline and 3 months after surgery: plaque index, gingival index, probing pocket depth, gingival recession, and clinical attachment level. Radiographic analysis was performed at baseline, 1 week and 3 months after surgery. Results Membrane exposure was not observed in any cases. Significant probing depth reduction, attachment-level gain and bone fill were observed for both test and control groups compared to baseline at 3 months after surgery (P<0.05). However, there were no statistically significant differences in clinical improvement and radiographic bone fill between treatment protocols (P>0.05). Conclusions Within the limitations of this study, the results suggest that both NC and BC were comparable in terms of clinical and radiographic outcomes for the treatment of periodontal intrabony defects in human subjects. Graphical Abstract PMID:25177521

  20. The role of barrier membranes for guided bone regeneration and restoration of large bone defects: current experimental and clinical evidence

    PubMed Central

    2012-01-01

    Treatment of large bone defects represents a great challenge in orthopedic and craniomaxillofacial surgery. Although there are several methods for bone reconstruction, they all have specific indications and limitations. The concept of using barrier membranes for restoration of bone defects has been developed in an effort to simplify their treatment by offering a sinlge-staged procedure. Research on this field of bone regeneration is ongoing, with evidence being mainly attained from preclinical studies. The purpose of this review is to summarize the current experimental and clinical evidence on the use of barrier membranes for restoration of bone defects in maxillofacial and orthopedic surgery. Although there are a few promising preliminary human studies, before clinical applications can be recommended, future research should aim to establish the 'ideal' barrier membrane and delineate the need for additional bone grafting materials aiming to 'mimic' or even accelerate the normal process of bone formation. Reproducible results and long-term observations with barrier membranes in animal studies, and particularly in large animal models, are required as well as well-designed clinical studies to evaluate their safety, efficacy and cost-effectiveness. PMID:22834465

  1. The role of barrier membranes for guided bone regeneration and restoration of large bone defects: current experimental and clinical evidence.

    PubMed

    Dimitriou, Rozalia; Mataliotakis, George I; Calori, Giorgio Maria; Giannoudis, Peter V

    2012-07-26

    Treatment of large bone defects represents a great challenge in orthopedic and craniomaxillofacial surgery. Although there are several methods for bone reconstruction, they all have specific indications and limitations. The concept of using barrier membranes for restoration of bone defects has been developed in an effort to simplify their treatment by offering a single-staged procedure. Research on this field of bone regeneration is ongoing, with evidence being mainly attained from preclinical studies. The purpose of this review is to summarize the current experimental and clinical evidence on the use of barrier membranes for restoration of bone defects in maxillofacial and orthopedic surgery. Although there are a few promising preliminary human studies, before clinical applications can be recommended, future research should aim to establish the 'ideal' barrier membrane and delineate the need for additional bone grafting materials aiming to 'mimic' or even accelerate the normal process of bone formation. Reproducible results and long-term observations with barrier membranes in animal studies, and particularly in large animal models, are required as well as well-designed clinical studies to evaluate their safety, efficacy and cost-effectiveness.

  2. ELECTROCHEMICAL CHROMIC ACID REGENERATION PROCESS: FITTING OF MEMBRANE TRANSPORT PROPERTIES. (R827125)

    EPA Science Inventory

    Abstract

    A mathematical model was developed to predict changes in contaminant concentrations with time, and to estimate contaminant fluxes due to migration, diffusion, and convection in a laboratory-scale batch electrolysis cell for the regeneration of contaminated har...

  3. Studies on electrochemical characterization and performance prediction of cellulose acetate and Zeocarb-225 composite membranes in aqueous NaCl solutions.

    PubMed

    Tiwari, A K; Ahmad, Suhail

    2006-06-01

    We have mixed cellulose acetate and Zeocarb-225 in different ratios, leading to the preparations of Membrane-1 and Membrane-2. Membrane potential, water content, and conductance measurements have been carried out to estimate and analyze the data in terms of equilibria and important electrochemical parameters. The Donnan equilibrium has been incorporated to estimate the activity coefficient of counterions, y(p)M, and solute, y(+/-)M in the membrane phase along with the parameter, so called varphi expressing non-ideality. Dependence of the extent of hydrophilicity of both membranes on mean electrolyte concentrations has been examined. Selectivity in membranes is discussed in terms of dissociation equilibria, K(d)s and K(d)f. It has been found that membrane surface charge density sigma(s) increases with increasing of external NaCl concentration. Dependence of water transport number and cationic transport number on electrolyte concentration shows a similar trend of variation. At higher mean concentration of electrolyte, water transport number in Membrane-2 has a negative value. Membrane-2 has a higher value of water transport number than Membrane-1. The entropy production due to solute and water transport has been quantified for both the membranes in the light of nonequilibrium thermodynamics. The various type of interactions such as solute-membrane, solute-water, and water-membrane are analyzed in terms of friction coefficients (f(ij)) of Spiegler's frictional pore model. In our case, an f(wm) < f(sm) < f(sw)-like trend is observed in both membranes. These frictional coefficients show close dependence on external electrolyte concentrations. Pore potential values of Membrane-1 and Membrane-2 have been worked out using the Poisson-Boltzmann equation. In both systems pore potential values increase with increasing mean electrolyte concentrations. The transport through Membrane-1 and Membrane-2 tends to follow diffusion-control criteria, i.e., (D(+/-) . C. d/D(+/-)M C

  4. Stretchable and strong cellulose nanopaper structures based on polymer-coated nanofiber networks: an alternative to nonwoven porous membranes from electrospinning.

    PubMed

    Sehaqui, Houssine; Morimune, Seira; Nishino, Takashi; Berglund, Lars A

    2012-11-12

    Nonwoven membranes based on electrospun fibers are of great interest in applications such as biomedical, filtering, and protective clothing. The poor mechanical performance is a limitation, as is some of the electrospinning solvents. To address these problems, porous nonwoven membranes based on nanofibrillated cellulose (NFC) modified by a hydroxyethyl cellulose (HEC) polymer coating are prepared. NFC/HEC aqueous suspensions are subjected to simple vacuum filtration in a paper-making fashion, followed by supercritical CO(2) drying. These nonwoven nanocomposite membranes are truly nanostructured and exhibit a nanoporous network structure with high specific surface area, as analyzed by nitrogen adsorption and FE-SEM. Mechanical properties evaluated by tensile tests show high strength combined with remarkably high strain to failure of up to 55%. XRD analysis revealed significant fibril realignment during tensile stretching. After postdrawing of the random mats, the modulus and strength are strongly increased. The present preparation route uses components from renewable resources, is environmentally friendly, and results in permeable membranes of exceptional mechanical performance.

  5. Epidermal Stem Cells Cultured on Collagen-Modified Chitin Membrane Induce In Situ Tissue Regeneration of Full-Thickness Skin Defects in Mice

    PubMed Central

    Shen, Yan; Dai, Libing; Li, Xiaojian; Liang, Rong; Guan, Guangxiong; Zhang, Zhi; Cao, Wenjuan; Liu, Zhihe; Mei, Shirley; Liang, Weiguo; Qin, Shennan; Xu, Jiake; Chen, Honghui

    2014-01-01

    A Large scale of full-thickness skin defects is lack of auto-grafts and which requires the engineered skin substitutes for repair and regeneration. One major obstacle in skin tissue engineering is to expand epidermal stem cells (ESCs) and develop functional substitutes. The other one is the scaffold of the ESCs. Here, we applied type I collagen-modified chitin membrane to form collagen-chitin biomimetic membrane (C-CBM), which has been proved to have a great biocompatibility and degraded totally when it was subcutaneously transplanted into rat skin. ESCs were cultured, and the resulting biofilm was used to cover full-thickness skin defects in nude mice. The transplantation of ESCs- collagen- chitn biomimetic membrane (ESCs-C-CBM) has achieved in situ skin regeneration. In nude mice, compared to controls with collagen-chitin biomimetic membrane (C-CBM) only, the ESCs-C-CBM group had significantly more dermatoglyphs on the skin wound 10 w after surgery, and the new skin was relatively thick, red and elastic. In vivo experiments showed obvious hair follicle cell proliferation in the full-thickness skin defect. Stem cell markers examination showed active ESCs in repair and regeneration of skin. The results indicate that the collagen-modified chitin membrane carry with ESCs has successfully regenerated the whole skin with all the skin appendages and function. PMID:24516553

  6. Biological Evaluation (In Vitro and In Vivo) of Bilayered Collagenous Coated (Nano Electrospun and Solid Wall) Chitosan Membrane for Periodontal Guided Bone Regeneration.

    PubMed

    Lotfi, Ghogha; Shokrgozar, Mohammad Ali; Mofid, Rasoul; Abbas, Fatemeh Mashhadi; Ghanavati, Farzin; Baghban, Alireza Akbarzadeh; Yavari, Seyedeh Kimia; Pajoumshariati, Seyedramin

    2016-07-01

    The application of barrier membranes in guided bone regeneration (GBR) has become a commonly used surgical technique in periodontal research. The objectives of this study were to evaluate the in vitro biocompatibility and osteogenic differentiation of mesenchymal stem cells (MSCs) on two different collagenous coatings (nano electrospun fibrous vs. solid wall) of bilayered collagen/chitosan membrane and their histological evaluation on bone regeneration in rabbit calvarial defects. It was found that chitosan-nano electrospun collagen (CNC) membranes had higher proliferation/metabolic activity compared to the chitosan-collagen (CC) and pristine chitosan membranes. The qRT-PCR analysis demonstrated the CNC membranes induced significant expression of osteogenic genes (Osteocalcin, RUNX2 and Col-α1) in MSCs. Moreover, higher calcium content and alkaline phosphatase activity of MSCs were observed compared to the other groups. Histologic and histomorphometric evaluations were performed on the uncovered (negative control) as well as covered calvarial defects of ten adult white rabbits with different membranes (CNC, CC, BioGide (BG, positive control)) at 1 and 2 months after surgery. More bone formation was detected in the defects covered with CNC and BG membranes than those covered by CC and the negative control. No inflammation and residual biomaterial particles were observed on the membrane surface or in the surrounding tissues in the surgical areas. These results suggest that bilayer CNC membrane can have the potential for use as a GBR membrane material facilitating bone formation.

  7. Conjugation of silica nanoparticles with cellulose acetate/polyethylene glycol 300 membrane for reverse osmosis using MgSO4 solution.

    PubMed

    Sabir, Aneela; Shafiq, Muhammad; Islam, Atif; Jabeen, Faiza; Shafeeq, Amir; Ahmad, Adnan; Zahid Butt, Muhammad Taqi; Jacob, Karl I; Jamil, Tahir

    2016-01-20

    Thermally-induced phase separation (TIPS) method was used to synthesize polymer matrix (PM) membranes for reverse osmosis from cellulose acetate/polyethylene glycol (CA/PEG300) conjugated with silica nanoparticles (SNPs). Experimental data showed that the conjugation of SNPs changed the surface properties as dense and asymmetric composite structure. The results were explicitly determined by the permeability flux and salt rejection efficiency of the PM-SNPs membranes. The effect of SNPs conjugation on MgSO4 salt rejection was more significant in magnitude than on permeation flux i.e. 2.38 L/m(2)h. FTIR verified that SNPs were successfully conjugated on the surface of PM membrane. DSC of PM-SNPs shows an improved Tg from 76.2 to 101.8 °C for PM and PM-S4 respectively. Thermal stability of the PM-SNPs membranes was observed by TGA which was significantly enhanced with the conjugation of SNPs. The micrographs of SEM and AFM showed the morphological changes and increase in the valley and ridges on membrane surface. Experimental data showed that the PM-S4 (0.4 wt% SNPs) membrane has maximum salt rejection capacity and was selected as an optimal membrane.

  8. Preparation and characterization of gatifloxacin-loaded sodium alginate hydrogel membranes supplemented with hydroxypropyl methylcellulose and hydroxypropyl cellulose polymers for wound dressing

    PubMed Central

    Prabu, Durai; Majdalawieh, Amin F.; Abu-Yousef, Imad A.; Inbasekaran, Kadambari; Balasubramaniam, Tharani; Nallaperumal, Narayanan; Gunasekar, Conjeevaram J.

    2016-01-01

    Introduction: The aim of this study is to evaluate gatifloxacin-loaded sodium alginate hydrogel membranes, supplemented with glycerol (a plasticizer), glutaraldehyde (a cross-linking agent), and hydroxypropyl methylcellulose (HPMC) or hydroxypropyl cellulose (HPC) polymers, as potential wound dressing materials based on their physicochemical properties and the sustain-release phenomenon. Materials and Methods: The physicochemical properties of the prepared hydrogel membranes were evaluated by several methods including Fourier transform infrared and differential scanning calorimetry. Different techniques were used to assess the swelling behavior, tensile strength and elongation, % moisture absorption, % moisture loss, water vapor transmission rate (WVTR), and microbial penetration for the hydrogel membranes. In vitro gatifloxacin release from the hydrogel membranes was examined using the United States Pharmacopeia XXIII dissolution apparatus. Four kinetics models (zero-order, first-order, Higuchi equation, and Korsmeyer-Peppas equation) were applied to study drug release kinetics. Results: The addition of glycerol, glutaraldehyde, HPMC, and HPC polymers resulted in a considerable increase in the tensile strength and flexibility/elasticity of the hydrogel membranes. WVTR results suggest that hydrated hydrogel membranes can facilitate water vapor transfer. None of the hydrogel membranes supported microbial growth. HPMC-treated and HPC-treated hydrogel membranes allow slow, but sustained, release of gatifloxacin for 48 h. Drug release kinetics revealed that both diffusion and dissolution play an important role in gatifloxacin release. Conclusions: Given their physicochemical properties and gatifloxacin release pattern, HPMC-treated and HPC-treated hydrogel membranes exhibit effective and sustained drug release. Furthermore, HPMC-treated and HPC-treated hydrogel membranes possess physiochemical properties that make them effective and safe wound dressing materials. PMID

  9. A new surgical management for oro-antral communication: the resorbable guided tissue regeneration membrane--bone substitute sandwich technique.

    PubMed

    Ogunsalu, C

    2005-09-01

    This paper describes a new technique for the closure of oro-antral fistula/communication, in which both hard tissue (bone) and soft tissue closure is achieved. The sandwich technique utilizes a suitable bone grafting material sandwiched between two sheaths of Biogide (a resorbable membrane) for the hard tissue closure of oro-antral communication post traumatic exodontia. The bone grafting material utilized for this case was Bio-oss. The result obtained was excellent with regeneration of sufficient bony tissue to allow placement of an endosseous implant. This sandwich technique is a simple and excellent technique for the closure of oro-antral communication, especially when subsequent placement of endosseous implant is considered without the need of donor site surgery for bone grafting. The otorhinolaryngologists and oral and maxillofacial surgeons should find this technique very useful in the closure of oro-antral fistulae.

  10. Forward osmosis process for dialysis fluid regeneration.

    PubMed

    Talaat, Khaled Mohamed

    2009-12-01

    In a preliminary experiment, 38% of the spent dialysis fluid water was reclaimed by a forward osmosis process through a cellulose triacetate membrane. The simplicity of forward osmosis and its minimal external energy requirements may allow the construction of a small bulk device that can reclaim a considerable portion of the water used in the patient's dialysis process. For developing an acceptable ambulatory dialysis system, decreasing the bulk of the fluid and equipment carried on the patient is essential. Forward osmosis may feasibly be used for dialysis fluid regeneration in ambulatory dialysis systems.

  11. Evaluation of 3D printed PCL/PLGA/β-TCP versus collagen membranes for guided bone regeneration in a beagle implant model.

    PubMed

    Won, J-Y; Park, C-Y; Bae, J-H; Ahn, G; Kim, C; Lim, D-H; Cho, D-W; Yun, W-S; Shim, J-H; Huh, J-B

    2016-10-07

    Here, we compared 3D-printed polycaprolactone/poly(lactic-co-glycolic acid)/β-tricalcium phosphate (PCL/PLGA/β-TCP) membranes with the widely used collagen membranes for guided bone regeneration (GBR) in beagle implant models. For mechanical property comparison in dry and wet conditions and cytocompatibility determination, we analyzed the rate and pattern of cell proliferation of seeded fibroblasts and preosteoblasts using the cell counting kit-8 assay and scanning electron microscopy. Osteogenic differentiation was verified using alizarin red S staining. At 8 weeks following implantation in vivo using beagle dogs, computed tomography and histological analyses were performed after sacrifice. Cell proliferation rates in vitro indicated that early cell attachment was higher in collagen than in PCL/PLGA/β-TCP membranes; however, the difference subsided by day 7. Similar outcomes were found for osteogenic differentiation, with approximately 2.5 times greater staining in collagen than PCL/PLGA/β-TCP, but without significant difference by day 14. In vivo, bone regeneration in the defect area, represented by new bone formation and bone-to-implant contact, paralleled those associated with collagen membranes. However, tensile testing revealed that whereas the PCL/PLGA/β-TCP membrane mechanical properties were conserved in both wet and dry states, the tensile property of collagen was reduced by 99% under wet conditions. Our results demonstrate in vitro and in vivo that PCL/PLGA/β-TCP membranes have similar levels of biocompatibility and bone regeneration as collagen membranes. In particular, considering that GBR is always applied to a wet environment (e.g. blood, saliva), we demonstrated that PCL/PLGA/β-TCP membranes maintained their form more reliably than collagen membranes in a wet setting, confirming their appropriateness as a GBR membrane.

  12. Simplifying corneal surface regeneration using a biodegradable synthetic membrane and limbal tissue explants.

    PubMed

    Deshpande, Pallavi; Ramachandran, Charanya; Sefat, Farshid; Mariappan, Indumathi; Johnson, Claire; McKean, Robert; Hannah, Melanie; Sangwan, Virender S; Claeyssens, Frederik; Ryan, Anthony J; MacNeil, Sheila

    2013-07-01

    Currently, damage to the ocular surface can be repaired by transferring laboratory cultured limbal epithelial cells (LECs) to the cornea using donor human amniotic membrane as the cell carrier. We describe the development of a synthetic biodegradable membrane of Poly D,L-lactide-co-glycolide (PLGA) with a 50:50 ratio of lactide and glycolide for the delivery of both isolated LECs and of cells grown out from limbal tissue explants. Both isolated LECs and limbal explants produced confluent limbal cultures within 2 weeks of culture on the membranes without the need for fibroblast feeder layers. Outgrowth of cells from explants was promoted by the inclusion of fibrin. Membranes with cells on them broke down predictably within 4-6 weeks in vitro and the breakdown was faster for a lower molecular weight (MW) (44 kg/mol) rather than a higher MW (153 kg/mol) PLGA. Membranes could be reproducibly produced, sterilised with gamma irradiation and stored dry at -20 °C for at least 12 months, and the ability to support cell outgrowth from explants was retained. We demonstrate transfer of cells (both isolated LECs and of cells grown out from limbal explants) from the membranes to an ex vivo rabbit cornea model. Characterisations of the cells by immunohistochemistry showed both differentiated and stem cell populations. A synthetic membrane combined with limbal explants in theatre would avoid the need for tissue banked human amniotic membrane and also avoid the need for specialist laboratory facilities for LEC expansion making this more accessible to many more surgeons and patients.

  13. Gypsum (CaSO4·2H2O) Scaling on Polybenzimidazole and Cellulose Acetate Hollow Fiber Membranes under Forward Osmosis

    PubMed Central

    Chen, Si Cong; Su, Jincai; Fu, Feng-Jiang; Mi, Baoxia; Chung, Tai-Shung

    2013-01-01

    We have examined the gypsum (CaSO4·2H2O) scaling phenomena on membranes with different physicochemical properties in forward osmosis (FO) processes. Three hollow fiber membranes made of (1) cellulose acetate (CA), (2) polybenzimidazole (PBI)/polyethersulfone (PES) and (3) PBI-polyhedral oligomeric silsesquioxane (POSS)/polyacrylonitrile (PAN) were studied. For the first time in FO processes, we have found that surface ionic interactions dominate gypsum scaling on the membrane surface. A 70% flux reduction was observed on negatively charged CA and PBI membrane surfaces, due to strong attractive forces. The PBI membrane surface also showed a slightly positive charge at a low pH value of 3 and exhibited a 30% flux reduction. The atomic force microscopy (AFM) force measurements confirmed a strong repulsive force between gypsum and PBI at a pH value of 3. The newly developed PBI-POSS/PAN membrane had ridge morphology and a contact angle of 51.42° ± 14.85° after the addition of hydrophilic POSS nanoparticles and 3 min thermal treatment at 95 °C. Minimal scaling and an only 1.3% flux reduction were observed at a pH value of 3. Such a ridge structure may reduce scaling by not providing a locally flat surface to the crystallite at a pH value of 3; thus, gypsum would be easily washed away from the surface. PMID:24957062

  14. Gypsum (CaSO4·2H2O) Scaling on Polybenzimidazole and Cellulose Acetate Hollow Fiber Membranes under Forward Osmosis.

    PubMed

    Chen, Si Cong; Su, Jincai; Fu, Feng-Jiang; Mi, Baoxia; Chung, Tai-Shung

    2013-11-08

    We have examined the gypsum (CaSO4·2H2O) scaling phenomena on membranes with different physicochemical properties in forward osmosis (FO) processes. Three hollow fiber membranes made of (1) cellulose acetate (CA), (2) polybenzimidazole (PBI)/polyethersulfone (PES) and (3) PBI-polyhedral oligomeric silsesquioxane (POSS)/polyacrylonitrile (PAN) were studied. For the first time in FO processes, we have found that surface ionic interactions dominate gypsum scaling on the membrane surface. A 70% flux reduction was observed on negatively charged CA and PBI membrane surfaces, due to strong attractive forces. The PBI membrane surface also showed a slightly positive charge at a low pH value of 3 and exhibited a 30% flux reduction. The atomic force microscopy (AFM) force measurements confirmed a strong repulsive force between gypsum and PBI at a pH value of 3. The newly developed PBI-POSS/PAN membrane had ridge morphology and a contact angle of 51.42° ± 14.85° after the addition of hydrophilic POSS nanoparticles and 3 min thermal treatment at 95 °C. Minimal scaling and an only 1.3% flux reduction were observed at a pH value of 3. Such a ridge structure may reduce scaling by not providing a locally flat surface to the crystallite at a pH value of 3; thus, gypsum would be easily washed away from the surface.

  15. Evaluation of PVA biodegradable electric conductive membranes for nerve regeneration in axonotmesis injuries: the rat sciatic nerve animal model.

    PubMed

    Ribeiro, Jorge; Caseiro, Ana Rita; Pereira, Tiago; Armada-da-Silva, Paulo Alexandre; Pires, Isabel; Prada, Justina; Amorim, Irina; Leal Reis, Inês; Amado, Sandra; Santos, José Domingos; Bompasso, Simone; Raimondo, Stefania; Varejão, Artur Severo Proença; Geuna, Stefano; Luís, Ana Lúcia; Maurício, Ana Colette

    2017-05-01

    The therapeutic effect of three polyvinyl alcohol (PVA) membranes loaded with electrically conductive materials - carbon nanotubes (PVA-CNTs) and polypyrrole (PVA-PPy) - were tested in vivo for neuro-muscular regeneration after an axonotmesis injury in the rat sciatic nerve. The membranes electrical conductivity measured was 1.5 ± 0.5 × 10(-6) S/m, 579 ± 0.6 × 10(-6) S/m, and 1837.5 ± 0.7 × 10(-6) S/m, respectively. At week-12, a residual motor and nociceptive deficit were present in all treated groups, but at week-12, a better recovery to normal gait pattern of the PVA-CNTs and PVA-PPy treated groups was observed. Morphometrical analysis demonstrated that PVA-CNTs group presented higher myelin thickness and lower g-ratio. The tibialis anterior muscle, in the PVA-PPy and PVA-CNTs groups showed a 9% and 19% increase of average fiber size area and a 5% and 10% increase of the "minimal Feret's diameter," respectively. No inflammation, degeneration, fibrosis or necrosis were detected in lung, liver, kidneys, spleen, and regional lymph nodes and absence of carbon deposits was confirmed with Von Kossa and Masson-Fontana stains. In conclusion, the membranes of PVA-CNTs and PVA-PPy are biocompatible and have electrical conductivity. The higher electrical conductivity measured in PVA-CNTs membrane might be responsible for the positive results on maturation of myelinated fibers. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 105A: 1267-1280, 2017.

  16. Improved tympanic membrane regeneration after myringoplastic surgery using an artificial biograft.

    PubMed

    Immich, A P S; Pennacchi, P C; Naves, A F; Felisbino, S L; Boemo, R L; Maria-Engler, S S; Catalani, L H

    2017-04-01

    Tympanic membrane perforations are due to common otologic problems. The current treatments to heal tympanic membrane perforation, such as myringoplasty, have some disadvantages, including the need for autologous grafting, which is rapidly absorbed by the organism before perforation recovery is complete. To improve the structural and functional tympanic membrane healing after surgery, we propose a new branch of artificial grafts. In this study, we report the development of artificial grafts using electrospun bioabsorbable polymers. Polymers such as poly (l-lactic acid) and poly (lactic-co-glycolic acid) acted as the scaffold for cell growth in a co-culture of fibroblasts and keratinocytes. This co-culture promoted the growth of an epithelial-equivalent tissue over the electrospun scaffold, which was used as an alternative graft in myringoplasty. The in vivo study was performed in Sprague Dawley rats. Ear endoscopy was performed 30days after surgery and showed that tympanic membrane perforations treated with artificial grafts healed naturally, completely and with the possibility of maintaining their actual functionality. In conclusion, our study described a new artificial graft created specifically to fulfill the requirements of perforated tympanic membrane healing processes, which are compatibility, proper durability and less intense side effects following myringoplasty.

  17. Synthesis of chitosan/hydroxyapatite membranes coated with hydroxycarbonate apatite for guided tissue regeneration purposes

    NASA Astrophysics Data System (ADS)

    Fraga, Alexandre Félix; Filho, Edson de Almeida; Rigo, Eliana Cristina da Silva; Boschi, Anselmo Ortega

    2011-02-01

    Chitosan, which is a non-toxic, biodegradable and biocompatible biopolymer, has been widely researched for several applications in the field of biomaterials. Calcium phosphate ceramics stand out among the so-called bioceramics for their absence of local or systemic toxicity, their non-response to foreign bodies or inflammations, and their apparent ability to bond to the host tissue. Hydroxyapatite (HA) is one of the most important bioceramics because it is the main component of the mineral phase of bone. The aim of this work was to produce chitosan membranes coated with hydroxyapatite using the modified biomimetic method. Membranes were synthesized from a solution containing 2% of chitosan in acetic acid (weight/volume) via the solvent evaporation method. Specimens were immersed in a sodium silicate solution and then in a 1.5 SBF (simulated body fluid) solution. The crystallinity of the HA formed over the membranes was correlated to the use of the nucleation agent (the sodium silicate solution itself). Coated membranes were characterized by means of scanning electron microscopy - SEM, X-ray diffraction - XRD, and Fourier transform infrared spectroscopy - FTIR. The results indicate a homogeneous coating covering the entire surface of the membrane and the production of a semi-crystalline hydroxyapatite layer similar to the mineral phase of human bone.

  18. [Use of native and cross-linked collagen membranes for guided tissue and bone regeneration].

    PubMed

    Schwarz, Frank; Sager, Martin; Rothamel, Daniel; Herten, Monika; Sculean, Anton; Becker, Jürgen

    2006-01-01

    A material which is used as a barrier for GBR/GTR procedures has to satisfy several physicochemical characteristics such as biocompatibility, tissue integration, barrier function, and dimensional stability. Recently, many investigations reported on the use of products derived from type I and type III porcine or bovine collagen. Collagen membranes are predominantly resorbed by enzymatic activity (protease and collagenase). To decrease resorption, various physical and chemical cross-linking techniques have been used. Although nowadays cross-linking of collagen seems to be a commonly used procedure, its impact on physicochemical properties of the membrane is still unknown. The aim of the present literature review is to evaluate the potential use of different collagen membranes for GBR/GTR procedures.

  19. Guided tissue regeneration (GTR) versus cementum-impregnated gelatine membrane (CGM) techniques: a histologic comparison of relative effectiveness in promoting periodontal attachment.

    PubMed

    Suwa, K

    1997-12-01

    Some prior reports have suggested that guided tissue regeneration (GTR) procedures achieve only partial regeneration and induces the ankylosis rather than true attachment. Accordingly, others have developed an alternative procedure employing gelatine membrane compounded with bovine cementum particles (CGM) which has proven effective in stimulating a more physiologic form of attachment. This study was undertaken to perform a direct comparison of histological results when CGM and GTR membrane were used at comparable sites in the same monkey. Three monkeys with no periodontal disease were used. Following flap surgery, recession type defects were created on the buccal side of the maxillary lateral incisors and second premolars, and the cementum was removed from the root surface at an area corresponding to the bone crest. The right and left lateral incisors and second premolars were covered with CGM and GTR membrane, respectively. The GTR membranes were removed after 4 weeks. At 6 wks, the animals were sacrificed, and specimens were prepared for histological examination. More coronally placed true new attachment was observed following application of CGM to the planed root surfaces. Application of the GTR membrane resulted in formation of bone-like cementum and ankylosis, whereas CGM established true periodontal regeneration.

  20. A morpholinium ionic liquid for cellulose dissolution.

    PubMed

    Raut, Dilip G; Sundman, Ola; Su, Weiqing; Virtanen, Pasi; Sugano, Yasuhito; Kordas, Krisztian; Mikkola, Jyri-Pekka

    2015-10-05

    A series of substituted morpholinium ionic salts and allyl ammonium acetates were prepared. Amongst those, N-allyl-N-methylmorpholinium acetate ([AMMorp][OAc]) was found to dissolve cellulose readily without any pre-processing of native cellulose. At 120°C, [AMMorp][OAc] could dissolve 30 wt%, 28 wt% and 25 wt% of cellulose with degree of polymerization (DPn) - 789, 1644 and 2082 respectively, in 20 min. Importantly, SEC analysis indicated that no discernible changes occurred in terms of the degree of polymerization of the different celluloses after regeneration. Furthermore, when comparing the cellulose dissolution capability of these newly synthesized ionic liquids, it is evident that the combination of all three constituents - the morpholinium cation, the existence of an allyl group and choosing the acetate anion are essential for efficient cellulose dissolution. The structure and morphology of the regenerated cellulosic materials were characterized by SEM, XRD, TGA, CP/MAS (13)C NMR and FTIR, respectively.

  1. Biosynthesis of membrane cholesterol during peripheral nerve development, degeneration and regeneration.

    PubMed

    Yao, J K

    1988-09-01

    Biosynthesis of peripheral nerve cholesterol was investigated by the in vivo and in vitro incorporation of [1-14C]-acetate into sciatic endoneurium of normal rats during development, degeneration and regeneration. Labeled sterols were rapidly formed (less than 10 min) within the endoneurial portion of sciatic nerve after [1-14C]acetate administration by intraneural injection. The majority of labeled sterols were initially found in lanosterol and desmosterol. After six hr, the 14C-labeling in both precursors was decreased to minimum, whereas cholesterol became the major labeled product of sterol. As myelination proceeded, the incorporation of [1-14C]acetate into endoneurial cholesterol decreased rapidly and reached a minimum after six mo. In mature adult nerve, an increased proportion of biosynthesis of lanosterol and desmosterol also was demonstrated. The in vitro incorporation of [1-14C]acetate into cholesterol was inhibited during Wallerian degeneration. Instead, cholesteryl esters were labeled as the major sterol product. Such inhibition, however, was not observed in the adult Trembler nerve (Brain Res. 325, 21-27, 1985), which is presumed to be due to a primary metabolic disorder of Schwann cells. The cholesterol biosynthesis was gradually resumed in degenerated nerve by either regeneration of crush-injured nerve or reattachment of the transected nerve. These results suggest that cholesterol biosynthesis in peripheral nerve relies on the axon to provide necessary substrates. De novo synthesis appears to be one of the major sources of endoneurial cholesterol that forms and maintains peripheral nerve myelin.

  2. Membrane filtration of Sudan orange G on a cellulose acetate membrane filter for separation-preconcentration and spectrophotometric determination in water, chili powder, chili sauce and tomato sauce samples.

    PubMed

    ALOthman, Zeid A; Unsal, Yunus E; Habila, Mohamed; Shabaka, Azza; Tuzen, Mustafa; Soylak, Mustafa

    2012-08-01

    A simple membrane filtration procedure for separation-enrichment of Sudan orange G is presented. The method is based on the adsorption of Sudan orange G on a cellulose acetate filter and its elution from the membrane with 10 mL of ethanol. Sudan orange G in the eluent was determined by UV-visible spectrophotometry at 388 nm. The effect of analytical conditions, including pH, flow rates and eluent, sample volume, type of membrane for quantitative preconcentration and separation of Sudan orange G were examined. The influences of matrix components on Sudan orange G recoveries were studied. The preconcentration factor was 125. The detection limit was 4.9 μg L(-1). The relative standard deviation was 4.3%. The presented procedure was applied to chili powder, chili sauce, tomato sauce, powdered beverage and water samples.

  3. Preparation and In Vitro Biological Evaluation of Octacalcium Phosphate/Bioactive Glass-Chitosan/ Alginate Composite Membranes Potential for Bone Guided Regeneration.

    PubMed

    Xu, Sanzhong; Chen, Xiaoyi; Yang, Xianyan; Zhang, Lei; Yang, Guojing; Shao, Huifeng; He, Yong; Gou, Zhongru

    2016-06-01

    The chitosan/alginate-trace element-codoped octacalcium phosphate/nano-sized bioactive glass (CS/ALG-teOCP/nBG) composite membranes were prepared by a layer-by-layer coating method for the functional requirement of guided bone regeneration (GBR). The morphology, mechanical properties and moisture content of the membranes was studied by scanning electron microscopy (SEM) observation, mechanical and swelling test. The results showed that the teOCP/nBG distributed uniformly in the composite membranes, and such as-prepared composite membrane exhibited an excellent tensile strength, accompanying with mechanical decay with immersion in aqueous medium. Cell culture and MTT assays showed that the surface microstructure and the ion dissolution products from teOCP/nBG components could enhance the cell proliferation, and especially the composite membranes was suitable for supporting the adhesion and growth behavior of human bone marrow mesenchymal stem cells (hBMSCs) in comparison with the CS/ALG pure polymer membranes. These results suggest that the new CS/ALG-teOCP/nBG composite membrane is highly bioactive and biodegradable, and favorable for guiding bone regeneration.

  4. Construction of nerve guide conduits from cellulose/soy protein composite membranes combined with Schwann cells and pyrroloquinoline quinone for the repair of peripheral nerve defect

    SciTech Connect

    Luo, Lihua; Gan, Li; Liu, Yongming; Tian, Weiqun; Tong, Zan; Wang, Xiong; Huselstein, Celine; Chen, Yun

    2015-02-20

    Regeneration and functional reconstruction of peripheral nerve defects remained a significant clinical challenge. Nerve guide conduits, with seed cells or neurotrophic factors (NTFs), had been widely used to improve the repair and regeneration of injured peripheral nerve. Pyrroloquinoline quinone (PQQ) was an antioxidant that can stimulate nerve growth factors (NGFs) synthesis and accelerate the Schwann cells (SCs) proliferation and growth. In present study, three kinds of nerve guide conduits were constructed: one from cellulose/SPI hollow tube (CSC), another from CSC combined with SCs (CSSC), and the third one from CSSC combined with PQQ (CSSPC), respectively. And then they were applied to bridge and repair the sciatic nerve defect in rats, using autograft as control. Effects of different nerve guide conduits on the nerve regeneration were comparatively evaluated by general analysis, sciatic function index (SFI) and histological analysis (HE and TEM). Newly-formed regenerative nerve fibers were observed and running through the transparent nerve guide conduits 12 weeks after surgery. SFI results indicated that the reconstruction of motor function in CSSPC group was better than that in CSSC and CSC groups. HE images from the cross-sections and longitudinal-sections of the harvested regenerative nerve indicated that regenerative nerve fibers had been formed and accompanied with new blood vessels and matrix materials in the conduits. TEM images also showed that lots of fresh myelinated and non-myelinated nerve fibers had been formed. Parts of vacuolar, swollen and abnormal axons occurred in CSC and CSSC groups, while the vacuolization and swell of axons was the least serious in CSSPC group. These results indicated that CSSPC group had the most ability to repair and reconstruct the nerve structure and functions due to the comprehensive contributions from hollow CSC tube, SCs and PQQ. As a result, the CSSPC may have the potential for the applications as nerve guide

  5. Construction of nerve guide conduits from cellulose/soy protein composite membranes combined with Schwann cells and pyrroloquinoline quinone for the repair of peripheral nerve defect.

    PubMed

    Luo, Lihua; Gan, Li; Liu, Yongming; Tian, Weiqun; Tong, Zan; Wang, Xiong; Huselstein, Celine; Chen, Yun

    2015-02-20

    Regeneration and functional reconstruction of peripheral nerve defects remained a significant clinical challenge. Nerve guide conduits, with seed cells or neurotrophic factors (NTFs), had been widely used to improve the repair and regeneration of injured peripheral nerve. Pyrroloquinoline quinone (PQQ) was an antioxidant that can stimulate nerve growth factors (NGFs) synthesis and accelerate the Schwann cells (SCs) proliferation and growth. In present study, three kinds of nerve guide conduits were constructed: one from cellulose/SPI hollow tube (CSC), another from CSC combined with SCs (CSSC), and the third one from CSSC combined with PQQ (CSSPC), respectively. And then they were applied to bridge and repair the sciatic nerve defect in rats, using autograft as control. Effects of different nerve guide conduits on the nerve regeneration were comparatively evaluated by general analysis, sciatic function index (SFI) and histological analysis (HE and TEM). Newly-formed regenerative nerve fibers were observed and running through the transparent nerve guide conduits 12 weeks after surgery. SFI results indicated that the reconstruction of motor function in CSSPC group was better than that in CSSC and CSC groups. HE images from the cross-sections and longitudinal-sections of the harvested regenerative nerve indicated that regenerative nerve fibers had been formed and accompanied with new blood vessels and matrix materials in the conduits. TEM images also showed that lots of fresh myelinated and non-myelinated nerve fibers had been formed. Parts of vacuolar, swollen and abnormal axons occurred in CSC and CSSC groups, while the vacuolization and swell of axons was the least serious in CSSPC group. These results indicated that CSSPC group had the most ability to repair and reconstruct the nerve structure and functions due to the comprehensive contributions from hollow CSC tube, SCs and PQQ. As a result, the CSSPC may have the potential for the applications as nerve guide

  6. Evaluation of clinical, antiinflammatory and antiinfective properties of amniotic membrane used for guided tissue regeneration: A randomized controlled trial

    PubMed Central

    Kumar, Aravind; Chandra, Rampalli Viswa; Reddy, Aileni Amarender; Reddy, Bavigadda Harish; Reddy, Chakravarthy; Naveen, Anumala

    2015-01-01

    Background: The objective of this study was to evaluate the antiinflammatory, antiinfective and clinical properties of amniotic membrane (AM) when used for guided tissue regeneration (GTR) in contained interdental defects. Materials and Methods: A total of 30 subjects participated in this study. Two sites in each subject were randomly assigned into each of the following experimental groups; test group: AM with bone graft and control group: Bone graft only. Clinical parameters included recording site-specific measures of plaque, gingivitis, probing pocket depth (PPD), and clinical attachment loss (CAL). The levels of interleukin-1β (IL-1β) and human beta-defensin-2 (hBD-2) levels in gingival crevicular fluid (GCF) from the test and control sites were measured by using commercially available enzyme linked immunosorbent assay kits. The evaluation of bone fill was performed by using digital subtraction technique and morphometric area analysis. One-way analysis of variance followed by the post-hoc test was used for intragroup and intergroup comparison. A P < 0.05 was considered as statistically significant. Results: Combination therapy using an AM increased bone fill and reduced PPD and CAL when compared to controls. AM also resulted in a significant reduction of GCF IL-1β levels and insignificant increase in the hBD-2 levels. Conclusion: From this trial conducted over a period of 24 weeks, AM demonstrated a marked antiinflammatory effect and its use resulted in an improvement in periodontal parameters. AM has the potential to function as a barrier for GTR and the unique properties associated with this material can augment its potential as a matrix for periodontal regeneration. PMID:25878677

  7. Analysis of diazinon pesticide using potentiometric biosensor based on enzyme immobilized cellulose acetate membrane in gold electrode

    NASA Astrophysics Data System (ADS)

    Mashuni; Ramadhan, L. O. A. N.; Jahiding, M.; Herniati

    2016-02-01

    Biosensor for analysis of diazinon pesticide using Potentiometric transducer has been developed. The basic element of this biosensor was a gold electrode modified with an immobilized acetylcholinesterase enzyme layer formed by entrapment with glutaraldehyde crosslinked-cellulose acetate. The aim of the research is to determine the composition of glutaraldehyde crosslinked-cellulose acetate in the gold electrode which provide optimum performance of biosensors of diazinon pesticide analysis on characterization include a range of working concentration, sensitivity, and detection limit. The results showed the composition of the cellulose acetate 15% and glutaraldehyde 25% that obtain optimum performance in the measurement of diazinon pesticide with a range of working concentration of 10-6 ppm to 1 ppm, the value of sensitivity 20.275 mV/decade and detection limit 10-6 ppm. The use of cellulose acetate provides highly sensitive devices allowing the efficient analysis of pesticides. The response time of electrode is on the measurement of pesticide diazinon with concentration variation of 10-6 ppm to 1 ppm with response time is about 5 minutes.

  8. Combination of microstereolithography and electrospinning to produce membranes equipped with niches for corneal regeneration.

    PubMed

    Ortega, Ilida; Sefat, Farshid; Deshpande, Pallavi; Paterson, Thomas; Ramachandran, Charanya; Ryan, Anthony J; MacNeil, Sheila; Claeyssens, Frederik

    2014-09-12

    Corneal problems affect millions of people worldwide reducing their quality of life significantly. Corneal disease can be caused by illnesses such as Aniridia or Steven Johnson Syndrome as well as by external factors such as chemical burns or radiation. Current treatments are (i) the use of corneal grafts and (ii) the use of stem cell expanded in the laboratory and delivered on carriers (e.g., amniotic membrane); these treatments are relatively successful but unfortunately they can fail after 3-5 years. There is a need to design and manufacture new corneal biomaterial devices able to mimic in detail the physiological environment where stem cells reside in the cornea. Limbal stem cells are located in the limbus (circular area between cornea and sclera) in specific niches known as the Palisades of Vogt. In this work we have developed a new platform technology which combines two cutting-edge manufacturing techniques (microstereolithography and electrospinning) for the fabrication of corneal membranes that mimic to a certain extent the limbus. Our membranes contain artificial micropockets which aim to provide cells with protection as the Palisades of Vogt do in the eye.

  9. Effects of collagen membranes enriched with in vitro-differentiated N1E-115 cells on rat sciatic nerve regeneration after end-to-end repair

    PubMed Central

    2010-01-01

    Peripheral nerves possess the capacity of self-regeneration after traumatic injury but the extent of regeneration is often poor and may benefit from exogenous factors that enhance growth. The use of cellular systems is a rational approach for delivering neurotrophic factors at the nerve lesion site, and in the present study we investigated the effects of enwrapping the site of end-to-end rat sciatic nerve repair with an equine type III collagen membrane enriched or not with N1E-115 pre-differentiated neural cells. After neurotmesis, the sciatic nerve was repaired by end-to-end suture (End-to-End group), end-to-end suture enwrapped with an equine collagen type III membrane (End-to-EndMemb group); and end-to-end suture enwrapped with an equine collagen type III membrane previously covered with neural cells pre-differentiated in vitro from N1E-115 cells (End-to-EndMembCell group). Along the postoperative, motor and sensory functional recovery was evaluated using extensor postural thrust (EPT), withdrawal reflex latency (WRL) and ankle kinematics. After 20 weeks animals were sacrificed and the repaired sciatic nerves were processed for histological and stereological analysis. Results showed that enwrapment of the rapair site with a collagen membrane, with or without neural cell enrichment, did not lead to any significant improvement in most of functional and stereological predictors of nerve regeneration that we have assessed, with the exception of EPT which recovered significantly better after neural cell enriched membrane employment. It can thus be concluded that this particular type of nerve tissue engineering approach has very limited effects on nerve regeneration after sciatic end-to-end nerve reconstruction in the rat. PMID:20149260

  10. Development of nanofibrous cellulose acetate/gelatin skin substitutes for variety wound treatment applications.

    PubMed

    Vatankhah, Elham; Prabhakaran, Molamma P; Jin, Guorui; Mobarakeh, Laleh Ghasemi; Ramakrishna, Seeram

    2014-02-01

    The major component of fibrous extracellular matrix of dermis is composed of a complex combination of proteins and polysaccharides. Electrospun cellulose acetate/gelatin might be an effective simulator of the structure and composition of native skin and during this study, we electrospun cellulose acetate/gelatin membranes in various compositions and their performance as a scaffold for either skin tissue engineering or as a wound dressing was evaluated. Skin treatment products, whether tissue-engineered scaffolds or wound dressings, should be sufficiently hydrophilic to allow for gas and fluid exchange and absorb excess exudates while controlling the fluid loss. However, a wound dressing should be easily removable without causing tissue damage and a tissue-engineered scaffold should be able to adhere to the wound, and support cell proliferation during skin regeneration. We showed that these distinct adherency features are feasible just by changing the composition of cellulose acetate and gelatin in composite cellulose acetate/gelatin scaffolds. High proliferation of human dermal fibroblasts on electrospun cellulose acetate/gelatin 25:75 confirmed the capability of cellulose acetate/gelatin 25:75 nanofibers as a tissue-engineered scaffold, while the electrospun cellulose acetate/gelatin 75:25 can be a potential low-adherent wound dressing.

  11. Counting cytopathogenic virus adsorbed to cellulose nitrate membrane filters as a simple method for counting viruses in raw sewage and sewage effluents.

    PubMed

    Mocé-Llivina, Laura; Jofre, Juan; Méndez, Xavier; Akkelidou, Dina; Lucena, Francisco; Papageorgiou, Georgios T

    2002-04-01

    Using the VIRMETADEN (acronym derived from virus adsorption enumeration) method to count cytopathogenic viruses adsorbed to cellulose nitrate membrane filters from prefiltered and decontaminated sewage samples was shown to be feasible. The numbers of naturally occurring enteroviruses recovered by the VIRMETADEN method were significantly higher than those obtained by standard plaque assay. For prefiltration of sewage samples, low protein binding polyvinylidene fluoride (PVDF) membranes of 0.65 and 5 microm pore size proved to be at least as good as prefilters used previously, both in the volume that could be filtered and in the low virus retention. Regarding decontamination, 0.22 microm pore size PVDF membranes were as good as chloroform treatment. Alternatively, decontamination with 0.05% phenol followed by filtration through 0.65 microm PVDF membrane filters proved to be an excellent method for clarifying and decontaminating the sample prior to enumerating viruses using the VIRMETADEN method. It allows good recovery and greater decontaminated sample volumes. The application of VIRMETADEN to decontaminated raw sewage and secondary effluent gave recoveries of approximately 100% of vaccinal polioviruses seeded in sewage. The advantage of this approach is that the same method is applicable to sewage affluents and effluents with a simple and fast method, which implies lower material and labour costs.

  12. Cellulose Synthesis and Its Regulation

    PubMed Central

    Li, Shundai; Bashline, Logan; Lei, Lei; Gu, Ying

    2014-01-01

    Cellulose, the most abundant biopolymer synthesized on land, is made of linear chains of ß (1–4) linked D-glucose. As a major structural component of the cell wall, cellulose is important not only for industrial use but also for plant growth and development. Cellulose microfibrils are tethered by other cell wall polysaccharides such as hemicellulose, pectin, and lignin. In higher plants, cellulose is synthesized by plasma membrane-localized rosette cellulose synthase complexes. Despite the recent advances using a combination of molecular genetics, live cell imaging, and spectroscopic tools, many aspects of the cellulose synthesis remain a mystery. In this chapter, we highlight recent research progress towards understanding the mechanism of cellulose synthesis in Arabidopsis. PMID:24465174

  13. ‘Reliability of new poly (lactic-co-glycolic acid) membranes treated with oxygen plasma plus silicon dioxide layers for pre-prosthetic guided bone regeneration processes’

    PubMed Central

    Castillo-Dalí, Gabriel; Batista-Cruzado, Antonio; López-Santos, Carmen; Rodríguez-González-Elipe, Agustín; Saffar, Jean-Louis; Lynch, Christopher D.; Gutiérrez-Pérez, José-Luis; Torres-Lagares, Daniel

    2017-01-01

    Background The use of cold plasmas may improve the surface roughness of poly(lactic-co-glycolic) acid (PLGA) membranes, which may stimulate the adhesion of osteogenic mediators and cells, thus accelerating the biodegradation of the barriers. Moreover, the incorporation of metallic-oxide particles to the surface of these membranes may enhance their osteoinductive capacity. Therefore, the aim of this paper was to evaluate the reliability of a new PLGA membrane after being treated with oxygen plasma (PO2) plus silicon dioxide (SiO2) layers for guided bone regeneration (GBR) processes. Material and Methods Circumferential bone defects (diameter: 11 mm; depth: 3 mm) were created on the top of eight experimentation rabbits’ skulls and were randomly covered with: (1) PLGA membranes (control), or (2) PLGA/PO2/SiO2 barriers. The animals were euthanized two months afterwards. A micromorphologic study was then performed using ROI (region of interest) colour analysis. Percentage of new bone formation, length of mineralised bone, concentration of osteoclasts, and intensity of ostheosynthetic activity were assessed and compared with those of the original bone tissue. The Kruskal-Wallis test was applied for between-group com Asignificance level of a=0.05 was considered. Results The PLGA/PO2/SiO2 membranes achieved the significantly highest new bone formation, length of mineralised bone, concentration of osteoclasts, and ostheosynthetic activity. The percentage of regenerated bone supplied by the new membranes was similar to that of the original bone tissue. Unlike what happened in the control group, PLGA/PO2/SiO2 membranes predominantly showed bone layers in advanced stages of formation. Conclusions The addition of SiO2 layers to PLGA membranes pre-treated with PO2 improves their bone-regeneration potential. Although further research is necessary to corroborate these conclusions in humans, this could be a promising strategy to rebuild the bone architecture prior to rehabilitate

  14. Development of a ratiometric fluorescent urea biosensor based on the urease immobilized onto the oxazine 170 perchlorate-ethyl cellulose membrane.

    PubMed

    Duong, Hong Dinh; Rhee, Jong Il

    2015-03-01

    In this work, the oxazine 170 perchlorate (O17)-ethyl cellulose (EC) membrane was successfully applied in the fabrication of a urea-sensing membrane. The urea-sensing membrane was a double layer consisting of the O17-EC membrane and a layer of the enzyme urease entrapped into EC matrix. The sensing principle of urea was based on the hydrolysis reaction of urea under the catalysis of the urease to produce ammonia in water and also on the binding of ammonia with the dye O17 to create the shift in the emission wavelength from λ(em)=630 nm to λ(em)=565 nm. The data collected from the ratio of the fluorescence intensities at λ(em)=630 nm and λ(em)=565 nm was proportional to urea concentration. The urea-sensing membrane with the ratiometric method was used to measure the concentrations of urea in the range of 0.01-0.1 M with a limit of detection (LOD) of 0.027 mM and 0.1-1.0 M with LOD of 0.224 mM. It showed fast response time, high reversibility and long-term stability in this concentration range. The recovery percentage of urea concentrations of the urea-sensing membrane for two kinds of biological urine solutions (BU1, BU2) was around 85-118%. The measured results were in good agreement with standard urea concentrations in the range of 0.06 M to 1.0 M.

  15. Fabrication of Blended Polycaprolactone/Poly (Lactic-Co-Glycolic Acid)/β-Tricalcium Phosphate Thin Membrane Using Solid Freeform Fabrication Technology for Guided Bone Regeneration

    PubMed Central

    Shim, Jin-Hyung; Huh, Jung-Bo; Park, Ju Young; Jeon, Young-Chan; Kang, Seong Soo; Kim, Jong Young; Rhie, Jong-Won

    2013-01-01

    This study developed a bioabsorbable-guided bone regeneration membrane made of blended polycaprolactone (PCL), poly(lactic-co-glycolic acid) (PLGA), and beta-tricalcium phosphate (β-TCP) using solid freeform fabrication (SFF) technology. The chemical and physical properties of the membrane were evaluated using field emission scanning electron microscopy, energy dispersive spectroscopy, and a tensile test. In vitro cell activity assays revealed that the adhesion, proliferation, and osteogenic differentiation of seeded adipose-derived stem cells (ADSCs) were significantly promoted by the PCL/PLGA/β-TCP membranes compared with PCL/PLGA membranes. When the PCL/PLGA and PCL/PLGA/β-TCP membranes were implanted on rabbit calvaria bone defects without ADSCs, microcomputed tomography and histological analyses confirmed that the SFF-based PCL/PLGA/β-TCP membranes greatly increased bone formation without the need for bone substitute materials. Moreover, tight integration, which helps to prevent exposure of the membrane, between both membranes and the soft tissues was clearly observed histologically. The SFF-based PCL/PLGA and PCL/PLGA/β-TCP membranes retained their mechanical stability for up to 8 weeks without significant collapse. Furthermore, PCL/PLGA/β-TCP underwent adequate degradation without a significant immune response at 8 weeks. PMID:22934667

  16. DNA stickers promote polymer adsorption onto cellulose.

    PubMed

    Sato, Teruaki; Ali, Md Monsur; Pelton, Robert; Cranston, Emily D

    2012-10-08

    Adsorption of oligonucleotides onto model cellulose surfaces was investigated by comparing the Boese and Breaker's cellulose binding oligonucleotide (CBO) with a nonspecific oligonucleotide control (NSO). Measurements using the quartz crystal microbalance with dissipation technique confirmed that CBO adsorbed onto cellulose more than NSO, particularly at high ionic strengths (100 mM CaCl(2)). CBO showed a higher maximum adsorption on nanofibrillated and nanocrystalline cellulose than on regenerated cellulose, indicating a preference for the native cellulose I crystal structure under conditions that favored specific adsorption over calcium-mediated electrostatically driven adsorption. In addition, an anionic polyacrylamide (A-PAM) with grafted CBO also adsorbed onto the surface of cellulose in CaCl(2), whereas the unmodified A-PAM did not. This work shows that CBO performs as a "sticker", facilitating the adsorption of polyacrylamide onto cellulose, even under high ionic strength conditions where the adsorption of conventional polyelectrolytes is inhibited.

  17. The chorioallantoic membrane (CAM) assay for the study of human bone regeneration: a refinement animal model for tissue engineering

    NASA Astrophysics Data System (ADS)

    Moreno-Jiménez, Inés; Hulsart-Billstrom, Gry; Lanham, Stuart A.; Janeczek, Agnieszka A.; Kontouli, Nasia; Kanczler, Janos M.; Evans, Nicholas D.; Oreffo, Richard Oc

    2016-08-01

    Biomaterial development for tissue engineering applications is rapidly increasing but necessitates efficacy and safety testing prior to clinical application. Current in vitro and in vivo models hold a number of limitations, including expense, lack of correlation between animal models and human outcomes and the need to perform invasive procedures on animals; hence requiring new predictive screening methods. In the present study we tested the hypothesis that the chick embryo chorioallantoic membrane (CAM) can be used as a bioreactor to culture and study the regeneration of human living bone. We extracted bone cylinders from human femoral heads, simulated an injury using a drill-hole defect, and implanted the bone on CAM or in vitro control-culture. Micro-computed tomography (μCT) was used to quantify the magnitude and location of bone volume changes followed by histological analyses to assess bone repair. CAM blood vessels were observed to infiltrate the human bone cylinder and maintain human cell viability. Histological evaluation revealed extensive extracellular matrix deposition in proximity to endochondral condensations (Sox9+) on the CAM-implanted bone cylinders, correlating with a significant increase in bone volume by μCT analysis (p < 0.01). This human-avian system offers a simple refinement model for animal research and a step towards a humanized in vivo model for tissue engineering.

  18. The chorioallantoic membrane (CAM) assay for the study of human bone regeneration: a refinement animal model for tissue engineering

    PubMed Central

    Moreno-Jiménez, Inés; Hulsart-Billstrom, Gry; Lanham, Stuart A.; Janeczek, Agnieszka A.; Kontouli, Nasia; Kanczler, Janos M.; Evans, Nicholas D.; Oreffo, Richard OC

    2016-01-01

    Biomaterial development for tissue engineering applications is rapidly increasing but necessitates efficacy and safety testing prior to clinical application. Current in vitro and in vivo models hold a number of limitations, including expense, lack of correlation between animal models and human outcomes and the need to perform invasive procedures on animals; hence requiring new predictive screening methods. In the present study we tested the hypothesis that the chick embryo chorioallantoic membrane (CAM) can be used as a bioreactor to culture and study the regeneration of human living bone. We extracted bone cylinders from human femoral heads, simulated an injury using a drill-hole defect, and implanted the bone on CAM or in vitro control-culture. Micro-computed tomography (μCT) was used to quantify the magnitude and location of bone volume changes followed by histological analyses to assess bone repair. CAM blood vessels were observed to infiltrate the human bone cylinder and maintain human cell viability. Histological evaluation revealed extensive extracellular matrix deposition in proximity to endochondral condensations (Sox9+) on the CAM-implanted bone cylinders, correlating with a significant increase in bone volume by μCT analysis (p < 0.01). This human-avian system offers a simple refinement model for animal research and a step towards a humanized in vivo model for tissue engineering. PMID:27577960

  19. Cellulose Microfibril Formation by Surface-Tethered Cellulose Synthase Enzymes.

    PubMed

    Basu, Snehasish; Omadjela, Okako; Gaddes, David; Tadigadapa, Srinivas; Zimmer, Jochen; Catchmark, Jeffrey M

    2016-02-23

    Cellulose microfibrils are pseudocrystalline arrays of cellulose chains that are synthesized by cellulose synthases. The enzymes are organized into large membrane-embedded complexes in which each enzyme likely synthesizes and secretes a β-(1→4) glucan. The relationship between the organization of the enzymes in these complexes and cellulose crystallization has not been explored. To better understand this relationship, we used atomic force microscopy to visualize cellulose microfibril formation from nickel-film-immobilized bacterial cellulose synthase enzymes (BcsA-Bs), which in standard solution only form amorphous cellulose from monomeric BcsA-B complexes. Fourier transform infrared spectroscopy and X-ray diffraction techniques show that surface-tethered BcsA-Bs synthesize highly crystalline cellulose II in the presence of UDP-Glc, the allosteric activator cyclic-di-GMP, as well as magnesium. The cellulose II cross section/diameter and the crystal size and crystallinity depend on the surface density of tethered enzymes as well as the overall concentration of substrates. Our results provide the correlation between cellulose microfibril formation and the spatial organization of cellulose synthases.

  20. Effect of rheological properties of dissolved cellulose/microfibrillated cellulose blend suspensions on film forming.

    PubMed

    Saarikoski, Eve; Rissanen, Marja; Seppälä, Jukka

    2015-03-30

    Enzymatically treated cellulose was dissolved in a NaOH/ZnO solvent system and mixed together with microfibrillated cellulose (MFC) in order to find the threshold in which MFC fibers form a percolation network within the dissolved cellulose solution and in order to improve the properties of regenerated cellulose films. In the aqueous state, correlations between the rheological properties of dissolved cellulose/MFC blend suspensions and MFC fiber concentrations were investigated and rationalized. In addition, rheological properties of diluted MFC suspensions were characterized and a correlation with NaOH concentration was found, thus partly explaining the flow properties of dissolved cellulose/MFC blend suspensions. Finally, based on results from Dynamic Mechanical Analysis (DMA), MFC addition had strengthening/plasticizing effect on regenerated cellulose films if low concentrations of MFC, below the percolation threshold (5.5-6 wt%, corresponding to 0.16-0.18 wt% of MFC in the blend suspensions), were used.

  1. Photochemical modification of poly(ether sulfone) ultrafiltration membranes by UV-assisted graft polymerization for the prevention of biofouling

    NASA Astrophysics Data System (ADS)

    Pieracci, John Paul

    Membranes are widely used by the biotechnology industry in the separation and recovery of proteins from biological solutions. Fouling of membrane surfaces by irreversible protein adsorption during ultrafiltration causes loss of membrane permeability and can reduce membrane selectivity and lead to significant product loss through denaturation. In this work, low fouling poly(ether sulfone) (PES) ultrafiltration membranes were produced by ultraviolet (UV) assisted graft polymerization of hydrophilic vinyl monomers using a newly developed photochemical dip modification technique. This technique was developed to make the UV modification process more easily adaptable to continuous membrane manufacturing processes. A method was also developed to measure and track the degree of polymer grafting on the membrane surface using attenuated total reflection Fourier transform infrared spectroscopy (FTIR/ATR). Grafting the hydrophilic monomer N-vinyl-2-pyrrolidinone (NVP) onto the membrane surface increased surface wettability and produced membranes with the high wettability of regenerated cellulose membranes. The enhanced surface wettability significantly decreased irreversible adsorptive fouling during the filtration of the protein bovine serum albumin (BSA). In order to maintain the rejection of BSA after modification, PES chain scission was tightly controlled by regulating the UV wavelength range and the light intensity used. The UV reactor system was operated with 300 nm UV lamps and a benzene filter used to remove high energy wavelengths below 275 nm that were determined to cause severe loss of BSA rejection due to pore enlargement from extensive chain scission. Dip modification caused membrane permeability to decrease due to the grafted chains blocking the membrane pores. The use of a chain transfer agent during modification followed by ethanol cleaning increased modified membrane permeability, but BSA rejection was severely decreased. The resultant membranes produced by

  2. Mechanisms of Membrane Preparation and Membrane Assays.

    DTIC Science & Technology

    The course of the work for the report period involved: Evaluating and developing testing procedures for membrane filters, and the construction, procurement of equipment for such testing; and Numerous sol preparations and castings of membranes using the acetate-butyrate esters of cellulose in lieu of the cellulose acetate in conjunction with the cellulose nitrate base of formulation. (Author)

  3. Novel meloxicam releasing electrospun polymer/ceramic reinforced biodegradable membranes for periodontal regeneration applications.

    PubMed

    Yar, Muhammad; Farooq, Ariba; Shahzadi, Lubna; Khan, Abdul Samad; Mahmood, Nasir; Rauf, Abdul; Chaudhry, Aqif Anwar; Rehman, Ihtesham Ur

    2016-07-01

    Periodontal disease is associated with the destruction of periodontal tissues, along with other disorders/problems including inflammation of tissues and severe pain. This paper reports the synthesis of meloxicam (MX) immobilized biodegradable chitosan (CS)/poly(vinyl alcohol) (PVA)/hydroxyapatite (HA) based electrospun (e-spun) fibers and films. Electrospinning was employed to produce drug loaded fibrous mats, whereas films were generated by solvent casting method. In-vitro drug release from materials containing varying concentrations of MX revealed that the scaffolds containing higher amount of drug showed comparatively faster release. During initial first few hours fast release was noted from membranes and films; however after around 5h sustained release was achieved. The hydrogels showed good swelling property, which is highly desired for soft tissue engineered implants. To investigate the biocompatibility of our synthesized materials, VERO cells (epithelial cells) were selected and cell culture results showed that these all materials were non-cytotoxic and also these cells were very well proliferated on these synthesized scaffolds. These properties along with the anti-inflammatory potential of our fabricated materials suggest their effective utilization in periodontital treatments.

  4. Collagen-graft mixed cellulose esters membrane maintains undifferentiated morphology and markers of potential pluripotency in feeder-free culture of induced pluripotent stem cells.

    PubMed

    Lotfalah Moradi, Sadegh; Hajishafieeha, Zahra; Nojedehi, Shahrzad; Dinarvand, Vida; Hesami Tackallou, Saeed; Roy, Ram V; Ardeshirylajimi, Abdolreza; Soleimani, Masoud

    2016-09-01

    Induced pluripotent stem cells (iPSCs) are unique and unlimited clinical sources of stem cell therapy for the regenerative medicine. Feeder layer preparation is an important step for iPSCs production, which is expensive, time-consuming and requires conversance. In the present study, we investigated the maintenance of pluripotency, and stemness of the iPSCs through feeder-free culture on a collagen-grafted Mixed Cellulose Esters membrane (MCE-COL) after three passages during twelve days. Results have demonstrated that the iPSCs cultured on MCE-COL membrane had a fine, typical undifferentiated morphology, increased proliferation rate and significant multi-lineage differentiation potential. Alkaline phosphatase (ALP) staining and pluripotency associated gene markers expression further confirmed that iPSCs cultured on the surface of MCE-COL had more ALP positive colonies and enhanced expression of Oct-4, Nanog, Sox-2 and ALP in comparison with MCE and control groups. Since MCE-COL membrane has three dimensional structure and bioactivity, it has the potential for usage in the feeder-free culture of iPSCs, and could be a suitable candidate to use as a feeder layer in stem cells preparation.

  5. Multifunctional Chitosan-45S5 Bioactive Glass-Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) Microsphere Composite Membranes for Guided Tissue/Bone Regeneration.

    PubMed

    Li, Wei; Ding, Yaping; Yu, Shanshan; Yao, Qingqing; Boccaccini, Aldo R

    2015-09-23

    Novel multifunctional chitosan-45S5 bioactive glass-poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) microsphere (CS-BG-MS) composite membranes were developed with applicability in guided tissue/bone regeneration (GTR/GBR). The incorporation of 45S5 BG and PHBV MS into CS membranes not only provided the membranes with favorable surface roughness, hydrophilicity, and flexibility but also slowed down their degradation rate. Moreover, the CS membranes became bioactive after the incorporation of 45S5 BG and capable of releasing drugs of different physicochemical properties in a controlled and sustained manner with the addition of PHBV MS. Cell culture tests showed that osteoblast-like MG-63 human osteosarcoma cells had significantly higher adhesion, cell proliferation, and alkaline phosphatase (ALP) activity on CS-BG and CS-BG-MS membranes than on neat CS membranes. Therefore, the developed bioactive CS-BG-MS membranes with potential multidrug (e.g., antibacterial and antiosteoporosis drugs) delivery capability are promising candidate membranes for GTR/GBR applications.

  6. Comparative study of chitosan/fibroin-hydroxyapatite and collagen membranes for guided bone regeneration in rat calvarial defects: micro-computed tomography analysis.

    PubMed

    Song, Jae Min; Shin, Sang Hun; Kim, Yong Deok; Lee, Jae Yeol; Baek, Young Jae; Yoon, Sang Yong; Kim, Hong Sung

    2014-06-01

    This study aimed to utilize micro-computed tomography (micro-CT) analysis to compare new bone formation in rat calvarial defects using chitosan/fibroin-hydroxyapatite (CFB-HAP) or collagen (Bio-Gide) membranes. Fifty-four (54) rats were studied. A circular bony defect (8 mm diameter) was formed in the centre of the calvaria using a trephine bur. The CFB-HAP membrane was prepared by thermally induced phase separation. In the experimental group (n=18), the CFB-HAP membrane was used to cover the bony defect, and in the control group (n=18), a resorbable collagen membrane (Bio-Gide) was used. In the negative control group (n=18), no membrane was used. In each group, six animals were euthanized at 2, 4 and 8 weeks after surgery. The specimens were then analysed using micro-CT. There were significant differences in bone volume (BV) and bone mineral density (BMD) (P<0.05) between the negative control group and the membrane groups. However, there were no significant differences between the CFB-HAP group and the collagen group. We concluded that the CFB-HAP membrane has significant potential as a guided bone regeneration (GBR) membrane.

  7. Comparative study of chitosan/fibroin–hydroxyapatite and collagen membranes for guided bone regeneration in rat calvarial defects: micro-computed tomography analysis

    PubMed Central

    Song, Jae Min; Shin, Sang Hun; Kim, Yong Deok; Lee, Jae Yeol; Baek, Young Jae; Yoon, Sang Yong; Kim, Hong Sung

    2014-01-01

    This study aimed to utilize micro-computed tomography (micro-CT) analysis to compare new bone formation in rat calvarial defects using chitosan/fibroin–hydroxyapatite (CFB–HAP) or collagen (Bio-Gide) membranes. Fifty-four (54) rats were studied. A circular bony defect (8 mm diameter) was formed in the centre of the calvaria using a trephine bur. The CFB–HAP membrane was prepared by thermally induced phase separation. In the experimental group (n=18), the CFB–HAP membrane was used to cover the bony defect, and in the control group (n=18), a resorbable collagen membrane (Bio-Gide) was used. In the negative control group (n=18), no membrane was used. In each group, six animals were euthanized at 2, 4 and 8 weeks after surgery. The specimens were then analysed using micro-CT. There were significant differences in bone volume (BV) and bone mineral density (BMD) (P<0.05) between the negative control group and the membrane groups. However, there were no significant differences between the CFB–HAP group and the collagen group. We concluded that the CFB–HAP membrane has significant potential as a guided bone regeneration (GBR) membrane. PMID:24722582

  8. Glucose, stem dry weight variation, principal component and cluster analysis for some agronomic traits among 16 regenerated Crotalaria juncea accessions for potential cellulosic ethanol.

    PubMed

    Morris, J Bradley; Antonious, George F

    2013-01-01

    The objectives of this research were to identify candidate sunn hemp accessions having high concentrations of cellulose for use as parents in breeding for cellulose and to determine variability for glucose content and some important agronomic traits among sunn hemp accessions. Since sunn hemp is an under-utilized species, glucose content and agronomic trait variation is essential for the identification of superior sunn hemp accessions for use as potential ethanol for biofuel. Sixteen sunn hemp accessions including the following plant introductions (expressed as glucose concentration) and stem dry weights were studied. "Sixteen sunn hemp accessions including the following plant introductions (expressed as glucose concentration) and stem dry weights were studied." In addition, to verify variability, these traits plus morphological, phenological, and seed reproductive traits were analyzed using multivariate and cluster analysis. The accessions, PI 250487, PI 337080, and PI 219717 produced the highest glucose concentrations (859, 809, and 770 mg g(-1) stem dry weight, respectively), however PI 468956 produced the highest stem dry weight (258 g). Branching significantly correlated with foliage (r(2) = 0.67**) and relative maturity (r(2) = 0.60*), while maturity had a significantly negative correlation with seed number (r(2) = -0.67**) and plant width (r(2) = -0.53*) as well. Seed number significantly correlated with plant width (r(2) = 0.57*). Average linkage cluster analysis grouped the 16 sunn hemp accessions into well-defined phenotypes with four distinct seed-producing groups and one outlier. Based on multivariate and cluster analysis, sufficient variation among these16 sunn hemp accessions exists to support the development of cellulosic ethanol producing cultivars with improved architecture, early maturity, seed yield, glucose concentrations, and stem dry weights.

  9. The evaluation of chorionic membrane in guided tissue regeneration for periodontal pocket therapy: a clinical and radiographic study.

    PubMed

    Kothiwale, Shaila V

    2014-03-01

    Periodontal regenerative therapy is aimed at reconstruction and to restore the architecture and function of lost or injured tissues. Melcher (J Periodontol 47(5):256-260, 1976) introduced the concept of guided tissue regeneration (GTR) for osseous reconstructive surgery. The aim of the present innovative clinical and radiographic study was to evaluate the effect of chorionic membrane (CM) in GTR in periodontal pocket therapy. Ten patients with moderate to severe periodontitis were selected in the single blind randomized controlled clinical trial. Patients were treated with periodontal pocket therapy along with CM in study sites and the control sites were treated with periodontal pocket therapy alone. The clinical parameters were recorded at baseline and 12 months. The radiographic parameters were recorded at baseline, 6 and 12 months. Clinical parameters included gingival index (GI), plaque index (PI), pocket probing depth (PPD) and relative attachment level (RAL). Digital images were analysed for bone gain (BG) and density. Data were evaluated using t test. Statistical significant differences were found in both sites at 12 months for GI, PI, PPD and RAL. Highly significant reduction was seen in GI 0.40 ± 0.08 (p = 0.0001), PI (0.41 ± 0.18), PPD 2.50 ± 0.53 mm (p = 0.0431) and increased BG 0.86 ± 0.18 (p < 0.0001) were observed in study sites. This shows that CM when used with pocket therapy can have influence on clinical parameters. Radiographic findings from this study demonstrated significant BG and density in sites treated with CM as compared to control sites.

  10. SURFACE MODIFICATION OF SILICA- AND CELLULOSE-BASED MICROFILTRATION MEMBRANES WITH FUNCTIONAL POLYAMINO ACIDS FOR HEAVY METAL SORPTION

    EPA Science Inventory

    Functionalized membranes represent a field with multiple applications. Examination of specific metal-macromolecule interactions on these surfaces presents an excellent method for characterizion of these materials. These interactions may also be exploited for heavy metal sorptio...

  11. Water Deficit Affects Primary Metabolism Differently in Two Lolium multiflorum/Festuca arundinacea Introgression Forms with a Distinct Capacity for Photosynthesis and Membrane Regeneration

    PubMed Central

    Perlikowski, Dawid; Czyżniejewski, Mariusz; Marczak, Łukasz; Augustyniak, Adam; Kosmala, Arkadiusz

    2016-01-01

    Understanding how plants respond to drought at different levels of cell metabolism is an important aspect of research on the mechanisms involved in stress tolerance. Furthermore, a dissection of drought tolerance into its crucial components by the use of plant introgression forms facilitates to analyze this trait more deeply. The important components of plant drought tolerance are the capacity for photosynthesis under drought conditions, and the ability of cellular membrane regeneration after stress cessation. Two closely related introgression forms of Lolium multiflorum/Festuca arundinacea, differing in the level of photosynthetic capacity during stress, and in the ability to regenerate their cellular membranes after stress cessation, were used as forage grass models in a primary metabolome profiling and in an evaluation of chloroplast 1,6-bisphosphate aldolase accumulation level and activity, during 11 days of water deficit, followed by 10 days of rehydration. It was revealed here that the introgression form, characterized by the ability to regenerate membranes after rehydration, contained higher amounts of proline, melibiose, galactaric acid, myo-inositol and myo-inositol-1-phosphate involved in osmoprotection and stress signaling under drought. Moreover, during the rehydration period, this form also maintained elevated accumulation levels of most the primary metabolites, analyzed here. The other introgression form, characterized by the higher capacity for photosynthesis, revealed a higher accumulation level and activity of chloroplast aldolase under drought conditions, and higher accumulation levels of most photosynthetic products during control and drought periods. The potential impact of the observed metabolic alterations on cellular membrane recovery after stress cessation, and on a photosynthetic capacity under drought conditions in grasses, are discussed. PMID:27504113

  12. Water Deficit Affects Primary Metabolism Differently in Two Lolium multiflorum/Festuca arundinacea Introgression Forms with a Distinct Capacity for Photosynthesis and Membrane Regeneration.

    PubMed

    Perlikowski, Dawid; Czyżniejewski, Mariusz; Marczak, Łukasz; Augustyniak, Adam; Kosmala, Arkadiusz

    2016-01-01

    Understanding how plants respond to drought at different levels of cell metabolism is an important aspect of research on the mechanisms involved in stress tolerance. Furthermore, a dissection of drought tolerance into its crucial components by the use of plant introgression forms facilitates to analyze this trait more deeply. The important components of plant drought tolerance are the capacity for photosynthesis under drought conditions, and the ability of cellular membrane regeneration after stress cessation. Two closely related introgression forms of Lolium multiflorum/Festuca arundinacea, differing in the level of photosynthetic capacity during stress, and in the ability to regenerate their cellular membranes after stress cessation, were used as forage grass models in a primary metabolome profiling and in an evaluation of chloroplast 1,6-bisphosphate aldolase accumulation level and activity, during 11 days of water deficit, followed by 10 days of rehydration. It was revealed here that the introgression form, characterized by the ability to regenerate membranes after rehydration, contained higher amounts of proline, melibiose, galactaric acid, myo-inositol and myo-inositol-1-phosphate involved in osmoprotection and stress signaling under drought. Moreover, during the rehydration period, this form also maintained elevated accumulation levels of most the primary metabolites, analyzed here. The other introgression form, characterized by the higher capacity for photosynthesis, revealed a higher accumulation level and activity of chloroplast aldolase under drought conditions, and higher accumulation levels of most photosynthetic products during control and drought periods. The potential impact of the observed metabolic alterations on cellular membrane recovery after stress cessation, and on a photosynthetic capacity under drought conditions in grasses, are discussed.

  13. Incorporation of N-doped TiO2 nanorods in regenerated cellulose thin films fabricated from recycled newspaper as a green portable photocatalyst.

    PubMed

    Mohamed, Mohamad Azuwa; Salleh, W N W; Jaafar, Juhana; Ismail, A F; Abd Mutalib, Muhazri; Jamil, Siti Munira

    2015-11-20

    In this work, an environmental friendly RC/N-TiO2 nanocomposite thin film was designed as a green portable photocatalyst by utilizing recycled newspaper as sustainable cellulose resource. Investigations on the influence of N-doped TiO2 nanorods incorporation on the structural and morphological properties of RC/N-TiO2 nanocomposite thin film are presented. The resulting nanocomposite thin film was characterized by FESEM, AFM, FTIR, UV-vis-NIR spectroscopy, and XPS analysis. The results suggested that there was a remarkable compatibility between cellulose and N-doped TiO2 nanorods anchored onto the surface of the RC/N-TiO2 nanocomposite thin film. Under UV and visible irradiation, the RC/N-TiO2 nanocomposite thin film showed remarkable photocatalytic activity for the degradation of methylene blue solution with degradation percentage of 96% and 78.8%, respectively. It is crucial to note that the resulting portable photocatalyst produced via an environmental and green technique in its fabrication process has good potential in the field of water and wastewater treatment application.

  14. Cellular Localization and Biochemical Characterization of a Chimeric Fluorescent Protein Fusion of Arabidopsis Cellulose Synthase-Like A2 Inserted into Golgi Membrane

    PubMed Central

    Lenucci, Marcello S.; Montefusco, Anna

    2014-01-01

    Cellulose synthase-like (Csl) genes are believed to encode enzymes for the synthesis of cell wall matrix polysaccharides. The subfamily of CslA is putatively involved in the biosynthesis of β-mannans. Here we report a study on the cellular localization and the enzyme activity of an Arabidopsis CslA family member, AtCslA2. We show that the fluorescent protein fusion AtCslA2-GFP, transiently expressed in tobacco leaf protoplasts, is synthesized in the ER and it accumulates in the Golgi stacks. The chimera is inserted in the Golgi membrane and is functional since membrane preparations obtained by transformed protoplasts carry out the in vitro synthesis of a 14C-mannan starting from GDP-d-[U-14C]mannose as substrate. The enzyme specific activity is increased by approximately 38% in the transformed protoplasts with respect to wild-type. Preliminary tests with proteinase K, biochemical data, and TM domain predictions suggest that the catalytic site of AtCslA2 faces the Golgi lumen. PMID:24558328

  15. Preparation and preliminary in vitro evaluation of a bFGF-releasing heparin-conjugated poly(ε-caprolactone) membrane for guided bone regeneration.

    PubMed

    Cao, Cong; Song, Ying; Yao, Qianqian; Yao, Yang; Wang, Tianlu; Huang, Bo; Gong, Ping

    2015-01-01

    In an effort to improve guided bone regeneration (GBR), we successfully fabricated a novel basic fibroblast growth factor (bFGF)-releasing heparin-conjugated poly(ε-caprolactone) membrane (hep-PCL/bFGF). This material has a porous microstructure with smooth and rough pore walls before and after heparinization, respectively. Our FTIR analyses indicated that chemical bonds were formed between PCL and heparin with a new amide C=O band at 1660 cm(-1) and a band at 3400 cm(-1) that can be attributed to -OH stretching in cross-linked heparin. We showed that bFGF was released from hep-PCL/bFGF in a continuous pattern, which remained for 3 weeks. We evaluated MG63 cell proliferation and biocompatibility of GBR membrane by a CCK-8 assay and a live/dead assay. The CCK-8 results revealed that the hep-PCL/bFGF group had superiority compared to other groups. Furthermore, cell morphology of hep-PCL membrane exhibited larger projected areas than those of PCL surfaces based on scanning electron microscopy analysis and immunofluorescent staining of cell cytoskeleton and vinculin expression. Our alkaline phosphatase activity assay also confirmed better performance of the hep-PCL/bFGF group. These results suggested that this novel hep-PCL/bFGF membrane is suitable for osteoblast-like cells to attach, proliferate, and differentiate. Therefore, the hep-PCL/bFGF membrane has potential to be a biodegradable membrane for GBR and warrants further investigation.

  16. Synthesis, micellization behavior and alcohol induced amphipathic cellulose film of cellulose-based amphiphilic surfactant

    NASA Astrophysics Data System (ADS)

    Yang, Fang; Liu, Ya-nan; Yu, Jian-ling; Li, Hai-peng; Li, Gang

    2015-08-01

    This paper presented a novel preparation method of the cellulose-based amphiphilic surfactant, and the surfactant was used to prepare amphipathic cellulose membrane. The native cotton cellulose was tailored to cellulose segments in ionic liquid 1-butyl-3-methylimidazolium chloride. Then, the hydrophobic and hydrophilic modification of cellulose segments were carried out by esterification and graft polymerization of the ɛ-caprolactone (ɛ-CL) monomer onto the hydroxyl group of cellulose as well as sulphonation with sulfamic acid. The amphipathic cellulose membrane was made by cellulose-based amphiphilic surfactant cross-linking with glutaraldehyde. The molecular structure of amphipathic cellulose surfactant was confirmed by FT-IR, and its surface active properties were investigated by Wilhelmy plate method and Steady-state fluorescence probe method, respectively. Experimental results showed that cellulose-based amphiphilic surfactant caused low interfacial tension of 48.62 mN/m and its critical micelle concentration (cmc) value was 0.65 wt% when the grafting ratio of cellulose-g-PCL (poly-caprolactone) was 25.40%. The contact angle between a droplet of water and the surface of membrane was 90.84o, and the surface free energy of the alcohol induced cellulose membrane was 15.7 mJ/m2. This study may help increase using natural and biodegradable surface-activity materials with improved properties as surfactants.

  17. The development of advanced cellulosic fibres.

    PubMed

    Woodings, C R

    1995-12-01

    For the majority of the last century, commercial routes to regenerated cellulose fibres have coped with the difficulties of making a good cellulose solution by using an easy to dissolve derivative (e.g. xanthate in the case of viscose rayon) or complex (e.g. cuprammonium rayon). For the purposes of this paper, advanced cellulosic fibres are defined as those made from a process involving direct dissolution of cellulose. The first examples of such fibres have now been generically designated as lyocell fibres to distinguish them from rayons, and the first commercial lyocell fibre is Courtaulds' Tencel.

  18. Adsorption of phospholipid bilayers onto pullulan-modified cellulose surfaces

    NASA Astrophysics Data System (ADS)

    Choi, Heejun; Liu, Zelin; Esker, Alan

    2009-03-01

    1,2-Dimyristoyl-sn-glycero-3-phosphocholine (DMPC) vesicle adsorption onto regenerated cellulose and pullulan 4-bromocinnamate (P4BC) modified cellulose surfaces was investigated via surface plasmon resonance (SPR) spectroscopy and quartz crystal microbalance with dissipation monitoring (QCM-D). P4BC with a degree of substitution (DS) of 0.061 ± 0.002 from UV measurements and 0.058 from ^1H NMR was synthesized from pullulan and 4-bromocinnamic acid to yield P4BC. The deduced thicknesses from SPR for DMPC layers were ˜3.7 nm (bilayer) on regenerated cellulose surfaces and ˜2.1 nm (monolayer) on P4BC modified cellulose surfaces. Qualitative analysis of the QCM-D data also indicated that the DMPC layers on P4BC modified cellulose surfaces were thinner than on regenerated cellulose surfaces.

  19. Silver nanoparticle/bacterial cellulose gel membranes for antibacterial wound dressing: investigation in vitro and in vivo.

    PubMed

    Wu, Jian; Zheng, Yudong; Wen, Xiaoxiao; Lin, Qinghua; Chen, Xiaohua; Wu, Zhigu

    2014-06-01

    Bacterial cellulose (BC) has attracted increasing attention as a novel wound dressing material, but its antimicrobial activity, which is one of the critical skin-barrier functions in wound healing, is not sufficient for use in practical applications. To overcome such a deficiency, silver nanoparticles were generated and self-assembled on the surface of BC nanofibers, forming a stable and evenly distributed Ag nanoparticle coated BC nanofiber (AgNP-BC). The performance of AgNP-BC was systematically studied in terms of antibacterial activities, cytocompatibility and effects on wound healing. The results showed that AgNP-BC exhibited significant antibacterial activity against Staphylococcus aureus. Moreover, AgNP-BC allowed attachment, and growth of rat fibroblasts with low cytotoxicity emerged. Based on these advantages, AgNP-BC samples were applied in a second-degree rat wound model. Wound flora showed a significant reduction during the healing. The fresh epidermal and dermis thicknesses with AgNP-BC samples were 111 and 855 µm respectively, higher than 74 and 619 µm for BC groups and 57 and 473 µm for untreated control wounds. The results demonstrated that AgNP-BC could reduce inflammation and promote scald wound healing.

  20. Metallization of bacterial cellulose for electrical and electronic device manufacture

    DOEpatents

    Evans, Barbara R.; O'Neill, Hugh M.; Jansen, Valerie Malyvanh; Woodward, Jonathan

    2006-01-17

    The employment of metallized bacterial cellulose in the construction of fuel cells and other electronic devices is disclosed. The fuel cell includes an electrolyte membrane comprising a membrane support structure comprising bacterial cellulose, an anode disposed on one side of the electrolyte membrane, and a cathode disposed on an opposite side of the electrolyte membrane. At least one of the anode and the cathode comprises an electrode support structure comprising bacterial cellulose, and a catalyst disposed in or on the electrode support structure.

  1. A Molecular Description of Cellulose Biosynthesis

    PubMed Central

    McNamara, Joshua T.; Morgan, Jacob L.W.; Zimmer, Jochen

    2016-01-01

    Cellulose is the most abundant biopolymer on Earth, and certain organisms from bacteria to plants and animals synthesize cellulose as an extracellular polymer for various biological functions. Humans have used cellulose for millennia as a material and an energy source, and the advent of a lignocellulosic fuel industry will elevate it to the primary carbon source for the burgeoning renewable energy sector. Despite the biological and societal importance of cellulose, the molecular mechanism by which it is synthesized is now only beginning to emerge. On the basis of recent advances in structural and molecular biology on bacterial cellulose synthases, we review emerging concepts of how the enzymes polymerize glucose molecules, how the nascent polymer is transported across the plasma membrane, and how bacterial cellulose biosynthesis is regulated during biofilm formation. Additionally, we review evolutionary commonalities and differences between cellulose synthases that modulate the nature of the cellulose product formed. PMID:26034894

  2. A molecular description of cellulose biosynthesis.

    PubMed

    McNamara, Joshua T; Morgan, Jacob L W; Zimmer, Jochen

    2015-01-01

    Cellulose is the most abundant biopolymer on Earth, and certain organisms from bacteria to plants and animals synthesize cellulose as an extracellular polymer for various biological functions. Humans have used cellulose for millennia as a material and an energy source, and the advent of a lignocellulosic fuel industry will elevate it to the primary carbon source for the burgeoning renewable energy sector. Despite the biological and societal importance of cellulose, the molecular mechanism by which it is synthesized is now only beginning to emerge. On the basis of recent advances in structural and molecular biology on bacterial cellulose synthases, we review emerging concepts of how the enzymes polymerize glucose molecules, how the nascent polymer is transported across the plasma membrane, and how bacterial cellulose biosynthesis is regulated during biofilm formation. Additionally, we review evolutionary commonalities and differences between cellulose synthases that modulate the nature of the cellulose product formed.

  3. Versatile Molding Process for Tough Cellulose Hydrogel Materials

    NASA Astrophysics Data System (ADS)

    Kimura, Mutsumi; Shinohara, Yoshie; Takizawa, Junko; Ren, Sixiao; Sagisaka, Kento; Lin, Yudeng; Hattori, Yoshiyuki; Hinestroza, Juan P.

    2015-11-01

    Shape-persistent and tough cellulose hydrogels were fabricated by a stepwise solvent exchange from a homogeneous ionic liquid solution of cellulose exposure to methanol vapor. The cellulose hydrogels maintain their shapes under changing temperature, pH, and solvents. The micrometer-scale patterns on the mold were precisely transferred onto the surface of cellulose hydrogels. We also succeeded in the spinning of cellulose hydrogel fibers through a dry jet-wet spinning process. The mechanical property of regenerated cellulose fibers improved by the drawing of cellulose hydrogel fibers during the spinning process. This approach for the fabrication of tough cellulose hydrogels is a major advance in the fabrication of cellulose-based structures with defined shapes.

  4. Versatile Molding Process for Tough Cellulose Hydrogel Materials

    PubMed Central

    Kimura, Mutsumi; Shinohara, Yoshie; Takizawa, Junko; Ren, Sixiao; Sagisaka, Kento; Lin, Yudeng; Hattori, Yoshiyuki; Hinestroza, Juan P.

    2015-01-01

    Shape-persistent and tough cellulose hydrogels were fabricated by a stepwise solvent exchange from a homogeneous ionic liquid solution of cellulose exposure to methanol vapor. The cellulose hydrogels maintain their shapes under changing temperature, pH, and solvents. The micrometer-scale patterns on the mold were precisely transferred onto the surface of cellulose hydrogels. We also succeeded in the spinning of cellulose hydrogel fibers through a dry jet-wet spinning process. The mechanical property of regenerated cellulose fibers improved by the drawing of cellulose hydrogel fibers during the spinning process. This approach for the fabrication of tough cellulose hydrogels is a major advance in the fabrication of cellulose-based structures with defined shapes. PMID:26537533

  5. Occurrence of serum M-protein species in Japanese patients older than 50 years based on relative mobility in cellulose acetate membrane electrophoresis.

    PubMed

    Kurihara, Y; Shiba, K; Fukumura, Y; Kobayashi, I; Kamei, S

    2000-01-01

    We investigated the occurrence of serum M-protein species in 2,007 Japanese patients older than 50 years of age. All sera samples were analyzed by cellulose acetate membrane electrophoresis. The relative mobility of an M-protein band was calculated by dividing the migration distance of M protein by that of albumin. M proteins were found to be present in 71 of 2,007 cases (3.5%). Men 80-89 years old showed the highest occurrence of M proteins, 11.0%. The relative mobility of M-protein bands, especially the band of the IgA-type M protein, increased as the patient's age advanced. The patients had higher levels of the IgG-type M protein than healthy Japanese subjects. We found that the occurrence of M-protein species in Japanese patients increases with their age. The IgG-type M protein was most frequently expressed among other types. The mobility of the M protein was greater in older patients probably because of aging-related changes in the carbohydrate chain of immunoglobulins composing an M-protein molecule.

  6. Triolein embedded cellulose acetate membrane as a tool to evaluate sequestration of PAHs in lake sediment core at large temporal scale.

    PubMed

    Tao, Yuqiang; Xue, Bin; Yao, Shuchun; Deng, Jiancai; Gui, Zhifan

    2012-04-03

    Although numerous studies have addressed sequestration of hydrophobic organic compounds (HOCs) in laboratory, little attention has been paid to its evaluation method in field at large temporal scale. A biomimetic tool, triolein embedded cellulose acetate membrane (TECAM), was therefore tested to evaluate sequestration of six PAHs with various hydrophobicity in a well-dated sediment core sampled from Nanyi Lake, China. Properties of sediment organic matter (OM) varying with aging time dominated the sequestration of PAHs in the sediment core. TECAM-sediment accumulation factors (MSAFs) of the PAHs declined with aging time, and significantly correlated with the corresponding biota-sediment accumulation factors (BSAFs) for gastropod (Bellamya aeruginosa) simultaneously incubated in the same sediment slices. Sequestration rates of the PAHs in the sediment core evaluated by TECAM were much lower than those obtained from laboratory study. The relationship between relative availability for TECAM (MSAF(t)/MSAF(0)) and aging time followed the first order exponential decay model. MSAF(t)/MSAF(0) was well-related to the minor changes of the properties of OM varying with aging time. Compared with chemical extraction, sequestration reflected by TECAM was much closer to that by B. aeruginosa. In contrast to B. aeruginosa, TECAM could avoid metabolism and the influences from feeding and other behaviors of organisms, and it is much easier to deploy and ready in laboratory. Hence TECAM provides an effective and convenient way to study sequestration of PAHs and probably other HOCs in field at large temporal scale.

  7. Nanofibers of cellulose and its derivatives fabricated using direct electrospinning.

    PubMed

    Ohkawa, Kousaku

    2015-05-19

    A short review with 49 references describes the electrospinninng (ES) process for polysaccharides, cellulose and chitosan, and their derivatives, including cellulose acetate and hydroxypropyl cellulose. A majority of applied studies adopted a two step-process, in which the cellulose acetate was used for the first ES process, followed by acetyl group removal to regenerate cellulose thin fibers. The electrospun nonwoven fabrics (ESNW) of regenerated cellulose can be modified by introduction of aldehyde groups by oxidative cleavage of vicinal diols using periodates, and these aldehyde groups serve as acceptors of foreign substances, with various chemical/biological functions, to be immobilized on the fiber surfaces in the ESNW matrices. Direct electrospinning of cellulose from trifluroacetic acid solution was also developed and the applied studies were summarized to conclude the current trends of interests in the ES and related technologies.

  8. In vitro cultivation of canine multipotent mesenchymal stromal cells on collagen membranes treated with hyaluronic acid for cell therapy and tissue regeneration

    PubMed Central

    Wodewotzky, T.I.; Lima-Neto, J.F.; Pereira-Júnior, O.C.M.; Sudano, M.J.; Lima, S.A.F.; Bersano, P.R.O.; Yoshioka, S.A.; Landim-Alvarenga, F.C.

    2012-01-01

    Support structures for dermal regeneration are composed of biodegradable and bioresorbable polymers, animal skin or tendons, or are bacteria products. The use of such materials is controversial due to their low efficiency. An important area within tissue engineering is the application of multipotent mesenchymal stromal cells (MSCs) to reparative surgery. The combined use of biodegradable membranes with stem cell therapy may lead to promising results for patients undergoing unsuccessful conventional treatments. Thus, the aim of this study was to test the efficacy of using membranes composed of anionic collagen with or without the addition of hyaluronic acid (HA) as a substrate for adhesion and in vitro differentiation of bone marrow-derived canine MSCs. The benefit of basic fibroblast growth factor (bFGF) on the differentiation of cells in culture was also tested. MSCs were collected from dog bone marrow, isolated and grown on collagen scaffolds with or without HA. Cell viability, proliferation rate, and cellular toxicity were analyzed after 7 days. The cultured cells showed uniform growth and morphological characteristics of undifferentiated MSCs, which demonstrated that MSCs successfully adapted to the culture conditions established by collagen scaffolds with or without HA. This demonstrates that such scaffolds are promising for applications to tissue regeneration. bFGF significantly increased the proliferative rate of MSCs by 63% when compared to groups without the addition of the growth factor. However, the addition of bFGF becomes limiting, since it has an inhibitory effect at high concentrations in culture medium. PMID:22983182

  9. In vitro cultivation of canine multipotent mesenchymal stromal cells on collagen membranes treated with hyaluronic acid for cell therapy and tissue regeneration.

    PubMed

    Wodewotzky, T I; Lima-Neto, J F; Pereira-Júnior, O C M; Sudano, M J; Lima, S A F; Bersano, P R O; Yoshioka, S A; Landim-Alvarenga, F C

    2012-12-01

    Support structures for dermal regeneration are composed of biodegradable and bioresorbable polymers, animal skin or tendons, or are bacteria products. The use of such materials is controversial due to their low efficiency. An important area within tissue engineering is the application of multipotent mesenchymal stromal cells (MSCs) to reparative surgery. The combined use of biodegradable membranes with stem cell therapy may lead to promising results for patients undergoing unsuccessful conventional treatments. Thus, the aim of this study was to test the efficacy of using membranes composed of anionic collagen with or without the addition of hyaluronic acid (HA) as a substrate for adhesion and in vitro differentiation of bone marrow-derived canine MSCs. The benefit of basic fibroblast growth factor (bFGF) on the differentiation of cells in culture was also tested. MSCs were collected from dog bone marrow, isolated and grown on collagen scaffolds with or without HA. Cell viability, proliferation rate, and cellular toxicity were analyzed after 7 days. The cultured cells showed uniform growth and morphological characteristics of undifferentiated MSCs, which demonstrated that MSCs successfully adapted to the culture conditions established by collagen scaffolds with or without HA. This demonstrates that such scaffolds are promising for applications to tissue regeneration. bFGF significantly increased the proliferative rate of MSCs by 63% when compared to groups without the addition of the growth factor. However, the addition of bFGF becomes limiting, since it has an inhibitory effect at high concentrations in culture medium.

  10. Selectivity of biopolymer membranes using HepG2 cells.

    PubMed

    Lü, Dongyuan; Gao, Yuxin; Luo, Chunhua; Lü, Shouqian; Wang, Qian; Xu, Xianghong; Sun, Shujin; Wang, Chengzhi; Long, Mian

    2015-03-01

    Bioartificial liver (BAL) system has emerged as an alternative treatment to bridge acute liver failure to either liver transplantation or liver regeneration. One of the main reasons that the efficacy of the current BAL systems was not convincing in clinical trials is attributed to the lack of friendly interface between the membrane and the hepatocytes in liver bioreactor, the core unit of BAL system. Here, we systematically compared the biological responses of hepatosarcoma HepG2 cells seeded on eight, commercially available biocompatible membranes made of acetyl cellulose-nitrocellulose mixed cellulose (CA-NC), acetyl cellulose (CA), nylon (JN), polypropylene (PP), nitrocellulose (NC), polyvinylidene fluoride (PVDF), polycarbonate (PC) and polytetrafluoroethylene (PTFE). Physicochemical analysis and mechanical tests indicated that CA, JN and PP membranes yield high adhesivity and reasonable compressive and/or tensile features with friendly surface topography for cell seeding. Cells prefer to adhere on CA, JN, PP or PTFE membranes with high proliferation rate in spheriod-like shape. Actin, albumin and cytokeratin 18 expressions are favorable for cells on CA or PP membrane, whereas protein filtration is consistent among all the eight membranes. These results further the understandings of cell growth, morphology and spreading, as well as protein filtration on distinct membranes in designing a liver bioreactor.

  11. Guided bone regeneration with beta-tricalcium phosphate and poly L-lactide-co-glycolide-co-epsilon-caprolactone membrane in partial defects of canine humerus.

    PubMed

    Oh, Taehoon; Rahman, Md Mizanur; Lim, Ji-Hey; Park, Mi-Sun; Kim, Dae-Yong; Yoon, Jung-hee; Kim, Wan Hee; Kikuchi, Masanori; Tanaka, Junzo; Koyama, Yoshihisa; Kweon, Oh-Kyeong

    2006-03-01

    This study was performed to evaluate the effect of betatricalcium phosphate and poly L-lactide-co-glycolide-coepsilon- caprolactone (TCP/PLGC) membrane in the repair of partial bone defects in canine proximal humerus. Three adult mixed-breed dogs were used during the experimental period. The length of the defect was quarter of the full length of humerus, and width of the defect was quarter of middle diameter of the lateral aspect of humerus. The humeri of each dog were divided into treatment (TCP/ PLGC) and control groups. The defect was covered with TCP/PLGC membrane in treatment group. To evaluate regeneration of the bone, computerized tomography (CT) and histopathologic examination were performed. The radiopaque lines were appeared at the original defect sites in TCP/PLGC group but below the original site in control at 4th week. Radiopacity and thickness of the defect sites, and radiopaque lines were more increased at 8th week than those of 4th week. Histopathologic findings revealed fibrous connective tissue migration into the defect and the migration inhibited the structure of new cortex to be placed in the original level in control whereas new cortex growth was found in the level of original line in TCP/ PLGC group. However, the new cortical bone in the TCP/ PLGC group was thinner and less organized than the adjacent intact cortex, and the amount of new cancellous bones were also scanty. The result suggested that TCP/ PLGC membrane is a good guided bone regeneration material to restore the original morphology of humerus in partial defect.

  12. Siloxane-grafted membranes

    DOEpatents

    Friesen, D.T.; Obligin, A.S.

    1989-10-31

    Composite cellulosic semipermeable membranes are disclosed which are the covalently bonded reaction product of an asymmetric cellulosic semipermeable membrane and a polysiloxane containing reactive functional group. The two reactants chemically bond by ether, ester, amide or acrylate linkages to form a siloxane-grafted cellulosic membrane having superior selectivity and flux stability. Selectivity may be enhanced by wetting the surface with a swelling agent such as water.

  13. Siloxane-grafted membranes

    DOEpatents

    Friesen, Dwayne T.; Obligin, Alan S.

    1989-01-01

    Composite cellulosic semipermeable membranes are disclosed which are the covalently bonded reaction product of an asymmetric cellulosic semipermeable membrane and a polysiloxane containing reactive functional groups. The two reactants chemically bond by ether, ester, amide or acrylate linkages to form a siloxane-grafted cellulosic membrane having superior selectivity and flux stability. Selectivity may be enhanced by wetting the surface with a swelling agent such as water.

  14. Cellulose Nanomaterials in Water Treatment Technologies

    PubMed Central

    Carpenter, Alexis Wells; de Lannoy, Charles François; Wiesner, Mark R.

    2015-01-01

    Cellulose nanomaterials are naturally occurring with unique structural, mechanical and optical properties. While the paper and packaging, automotive, personal care, construction, and textiles industries have recognized cellulose nanomaterials’ potential, we suggest cellulose nanomaterials have great untapped potential in water treatment technologies. In this review, we gather evidence of cellulose nanomaterials’ beneficial role in environmental remediation and membranes for water filtration, including their high surface area-to-volume ratio, low environmental impact, high strength, functionalizability, and sustainability. We make direct comparison between cellulose nanomaterials and carbon nanotubes (CNTs) in terms of physical and chemical properties, production costs, use and disposal in order to show the potential of cellulose nanomaterials as a sustainable replacement for CNTs in water treatment technologies. Finally, we comment on the need for improved communication and collaboration across the myriad industries invested in cellulose nanomaterials production and development to achieve an efficient means to commercialization. PMID:25837659

  15. Cellulose nanomaterials in water treatment technologies.

    PubMed

    Carpenter, Alexis Wells; de Lannoy, Charles-François; Wiesner, Mark R

    2015-05-05

    Cellulose nanomaterials are naturally occurring with unique structural, mechanical and optical properties. While the paper and packaging, automotive, personal care, construction, and textiles industries have recognized cellulose nanomaterials' potential, we suggest cellulose nanomaterials have great untapped potential in water treatment technologies. In this review, we gather evidence of cellulose nanomaterials' beneficial role in environmental remediation and membranes for water filtration, including their high surface area-to-volume ratio, low environmental impact, high strength, functionalizability, and sustainability. We make direct comparison between cellulose nanomaterials and carbon nanotubes (CNTs) in terms of physical and chemical properties, production costs, use and disposal in order to show the potential of cellulose nanomaterials as a sustainable replacement for CNTs in water treatment technologies. Finally, we comment on the need for improved communication and collaboration across the myriad industries invested in cellulose nanomaterials production and development to achieve an efficient means to commercialization.

  16. Guided bone regeneration produced by new mineralized and reticulated collagen membranes in critical-sized rat calvarial defects.

    PubMed

    Veríssimo, Denusa M; Leitão, Renata F C; Figueiró, Sônia D; Góes, Júlio C; Lima, Vilma; Silveira, Charles O; Brito, Gerly A C

    2015-02-01

    The aim of this study was to evaluate the bone regenerative effect of glutaraldehyde (GA) cross-linking on mineralized polyanionic collagen membranes in critical-sized defects on rat calvarias. Bone calvarial defects were induced in Wistar rats, which were then divided into five groups: a sham group; a control group, which received a commercial membrane; and GA, 25GA, and 75GA groups, which received one of three different polyanionic collagen membranes mineralized by 0, 25, or 75 hydroxyapatite cycles and then cross-linked by GA. Bone formation was evaluated based on digital radiography and computerized tomography. Histological analyses were performed 4 and 12 weeks after the surgical procedure to observe bone formation, membrane resorption, and fibrous tissue surrounding the membranes. Measurement of myeloperoxidase activity, tumor necrosis factor alpha, and interleukin 1beta production was performed 24 h after surgery. The percentage of new bone formation in the GA, 25GA, and 75GA groups was higher compared with the control and sham groups. In the GA and 25 GA groups, the membranes were still in place and were contained in a thick fibrous capsule after 12 weeks. No significant difference was found among the groups regarding myeloperoxidase activity and interleukin 1beta levels, although the GA, 25GA, and 75GA groups presented decreased levels of tumor necrosis factor alpha compared with the control group. These new GA cross-linked membranes accelerated bone healing of the calvarium defects and did not induce inflammation. In addition, unlike the control membrane, the experimental membranes were not absorbed during the analyzed period, so they may offer advantages in large bone defects where prolonged membrane barrier functions are desirable.

  17. Clinical outcomes of guided tissue regeneration with Atrisorb membrane in the treatment of intrabony defects: a 3-year follow-up study.

    PubMed

    Sakallioglu, Umur; Yavuz, Umit; Lütfioglu, Müge; Keskiner, Ilker; Açikgöz, Gökhan

    2007-02-01

    In this controlled clinical trial, initial and long-term treatment outcomes of guided tissue regeneration (GTR) were investigated for a synthetic absorbable membrane (Atrisorb) in intrabony defects. Eighteen defects in 16 patients received GTR with Atrisorb (test), with the membrane applied by an indirect method, and 15 defects in 15 patients were treated with open flap debridement (control). Probing pocket depth (PPD), gingival recession (GR), clinical attachment level (CAL), and linear alveolar bone level (ABL) were recorded at baseline and at 1 and 3 years following the treatment procedures and were assessed as the therapeutic outcome parameters. Both groups demonstrated significant PPD reduction and CAL and ABL gain after 1 year. Among these parameters, alterations in PPD and CAL were statistically significantly greater in the test group than the control group 1 year postsurgery. No significant changes were noted in the parameters of the first year between and within the study groups after 3 years. The results suggest that GTR performed with Atrisorb membrane via an indirect application method may provide favorable clinical outcomes for intrabony defects, and these outcomes may be maintained at least as well as open flap debridement over an extended period.

  18. Fibrous guided tissue regeneration membrane loaded with anti-inflammatory agent prepared by coaxial electrospinning for the purpose of controlled release

    NASA Astrophysics Data System (ADS)

    He, Min; Xue, Jiajia; Geng, Huan; Gu, Hao; Chen, Dafu; Shi, Rui; Zhang, Liqun

    2015-04-01

    Here, with the aim of inhibiting inflammation during guided tissue regeneration membrane (GTRM) implant surgery, coaxial electrospinning was used to fabricate drug-loaded core/sheath nanofiber GTRMs capable of controlled drug release. Various amounts of the anti-inflammatory agent metronidazole (MNA) were encapsulated into the core/sheath nanofibers (where PCL was the core, gelatin the sheath, and the gelatin shell was crosslinked with genipin) in order to establish the minimal drug content necessary to achieve the appropriate anti-inflammatory effect. By using TEM and SEM, the core/sheath structure was confirmed. In vitro drug disolution results showed that the core/sheath nanofibers exhibited sustained release profiles that were superior to those nanofibers produced by blending electrospinning. Additionally, the membrane significantly inhibited the colonization of anaerobic bacteria. Furthermore, with gelatin as a shell, the core/shell nanofiber membranes showed improved hydrophilicity, which resulted in better cell adhesion and proliferation without cytotoxicity. Therefore, in this study, a simple and effective coaxial electrospinning approach was demonstrated for the fabrication of anti-inflammatory GTRMs capable of providing controlled drug release.

  19. Sensor technologies based on a cellulose supported platform.

    PubMed

    Poplin, Jane Holly; Swatloski, Richard P; Holbrey, John D; Spear, Scott K; Metlen, Andreas; Grätzel, Michael; Nazeeruddin, Mohammad K; Rogers, Robin D

    2007-05-28

    A simple approach to sensor development based on encapsulating a probe molecule in a cellulose support followed by regeneration from an ionic liquid solution is demonstrated here by the codissolution of cellulose and 1-(2-pyridylazo)-2-naphthol in 1-butyl-3-methylimidazolium chloride followed by regeneration with water to form strips which exhibit a proportionate (1 : 1) response to Hg(II) in aqueous solution.

  20. Clinical and radiographic evaluation of the effects of guided tissue regeneration using resorbable membranes after extraction of impacted mandibular third molars.

    PubMed

    Aimetti, Mario; Pigella, Enrico; Romano, Federica

    2007-02-01

    The aim of this investigation was to evaluate the healing following guided tissue regeneration of bone defects distal to the mandibular second molars after surgical extraction of soft tissue-impacted, mesioangularly inclined third molars. After the impacted third molars were extracted, 15 sites were treated with polyglycolic acid/polylactic acid bioresorbable membranes plus scaling and root planing (SRP) of the distal surface of the second molars (test sites); 15 sites were treated with SRP alone (control sites) according to a split-mouth design. At 12 months after surgery, the placement of barrier material was shown to have resulted in statistically significant differences in clinical attachment level and bone gain compared to control sites.

  1. Efficacy of rhBMP-2 loaded PCL/PLGA/β-TCP guided bone regeneration membrane fabricated by 3D printing technology for reconstruction of calvaria defects in rabbit.

    PubMed

    Shim, Jin-Hyung; Yoon, Min-Chul; Jeong, Chang-Mo; Jang, Jinah; Jeong, Sung-In; Cho, Dong-Woo; Huh, Jung-Bo

    2014-11-10

    We successfully fabricated a three-dimensional (3D) printing-based PCL/PLGA/β-TCP guided bone regeneration (GBR) membrane that slowly released rhBMP-2. To impregnate the GBR membrane with intact rhBMP-2, collagen solution encapsulating rhBMP-2 (5 µg ml(-1)) was infused into pores of a PCL/PLGA/β-TCP membrane constructed using a 3D printing system with four dispensing heads. In a release profile test, sustained release of rhBMP-2 was observed for up to 28 d. To investigate the efficacy of the GBR membrane on bone regeneration, PCL/PLGA/β-TCP membranes with or without rhBMP-2 were implanted in an 8 mm calvaria defect of rabbits. Bone formation was evaluated at weeks 4 and 8 histologically and histomorphometrically. A space making ability of the GBR membrane was successfully maintained in both groups, and significantly more new bone was formed at post-implantation weeks 4 and 8 by rhBMP-2 loaded GBR membranes. Interestingly, implantation with rhBMP-2 loaded GBR membranes led to almost entire healing of calvaria defects within 8 weeks.

  2. Degradation and resynthesis of gap junction protein in plasma membranes of regenerating liver after partial hepatectomy or cholestasis

    PubMed Central

    Traub, Otto; Drüge, Petra Maria; Willecke, Klaus

    1983-01-01

    Changes in the total amount of the gap junction protein (Mr 26,000) after partial hepatectomy or bile duct ligation and recanalization were investigated in rat liver membranes by quantitative immunoblot with rabbit antiserum to the Mr 26,000 protein. The loss and reappearance of the Mr 26,000 protein roughly paralleled loss and reappearance of gap junction plaques analyzed previously under similar physiological conditions by freeze-fracture of hepatocyte surfaces. The total amount of the hepatic Mr 26,000 protein in liver plasma membranes and the total area of the hepatocyte surface occupied by gap junction plaques appeared to be proportional under these conditions. However, at the minimum, 28-35 hr after partial hepatectomy we still find about 15% of the Mr 26,000 protein, in contrast to <1% of gap junction plaques, determined by morphometric analysis. This discrepancy is probably due to the fact that very small gap junction plaques, single connexons, and free Mr 26,000 gap junction subunits are missed by the morphometric analysis. At the times of the minimal amount of the Mr 26,000 protein in hepatic plasma membranes after partial hepatectomy or bile duct ligation we found that crude hepatic lysosomal membranes of these rats contained less Mr 26,000 protein than lysosomal membranes of nonoperated control animals. Thus, we conclude that the decrease and increase of the total amount of the Mr 26,000 protein cannot be explained only by dispersal and reuse of gap junction subunits but are largely due to degradation and resynthesis of the Mr 26,000 protein. No significant change in the amount of the Mr 21,000 protein that had been isolated with gap junction plaques was observed in liver plasma membranes after partial hepatectomy. This confirms our previous conclusion that the Mr 26,000 and Mr 21,000 proteins are independent of each other. Images PMID:6298773

  3. Fabrication of metronidazole loaded poly (ε-caprolactone)/zein core/shell nanofiber membranes via coaxial electrospinning for guided tissue regeneration.

    PubMed

    He, Min; Jiang, Huiyi; Wang, Rui; Xie, Yi; Zhao, Changsheng

    2017-03-15

    To develop a biologically mimetic guided tissue regeneration (GTR) membrane with localized sustained drug release function to prevent infection, coaxial electrospinning technique was conducted to fabricate metronidazole (MNA)-loaded poly (ε-caprolactone) (PCL)/zein core/shell nanofibers. The nanofibers displayed a uniform bead-free round morphology as observed by scanning electron microscopy (SEM), and a core/shell structure as confirmed by transmission electron microscopy (TEM). X-ray diffraction (XRD) and differential scanning calorimetry (DSC) characterizations demonstrated that the MNA was well dispersed in the nanofibers matrix. Due to the encapsulation of the hydrophobic zein, the MNA was released in a controlled, sustained manner over 4days, and the released MNA showed high antibacterial activity towards anaerobic bacteria. In addition, the encapsulation of natural zein resulted in enhanced cell adhesion and proliferation, and the loading of MNA did not show any cytotoxicity. Thus, these results demonstrated that the MNA-loaded core/shell nanofibers had the potential to be used as GTR membranes with antibacterial function for extensive biomedical applications.

  4. Membrane surface functionalization via theophylline derivative coating and streptavidin immobilization.

    PubMed

    Hierrezuelo, J; Romero, V; Benavente, J; Rico, R; López-Romero, J Manuel

    2014-01-01

    Poly(vinylidene fluoride) (PVDF) and regenerated cellulose (RC) membranes were surface-modified by the adsorption of one adenosine receptor antagonist: the theophylline-oligo(ethylene glycol)-alkene derivative, Theo1. Surface modification was carried out by immersion of the membrane in a dichloromethane solution of Theo1 (PVDF+Theo1 and RC+Theo1 samples). Membrane surfaces with partial coverage by theophylline and/or its inclusion in the membrane structures were studied by X-ray photoelectron spectroscopy (XPS), solid-state nuclear magnetic resonance (SNMR), impedance spectroscopy (IS) and contact angle (CA) measurements. The Theo1 orientation was inferred from the data. Streptavidin (SA) was immobilized onto the membrane/Theo1 hybrid material. The protein-theophylline Theo1 interaction was visualized with bright field microscopy (BFM).

  5. Concurrent measurements of size-segregated particulate sulfate, nitrate and ammonium using quartz fiber filters, glass fiber filters and cellulose membranes

    NASA Astrophysics Data System (ADS)

    Tian, Shili; Pan, Yuepeng; Wang, Jian; Wang, Yuesi

    2016-11-01

    Current science and policy requirements have focused attention on the need to expand and improve particulate matter (PM) sampling methods. To explore how sampling filter type affects artifacts in PM composition measurements, size-resolved particulate SO42-, NO3- and NH4+ (SNA) were measured on quartz fiber filters (QFF), glass fiber filters (GFF) and cellulose membranes (CM) concurrently in an urban area of Beijing on both clean and hazy days. The results showed that SNA concentrations in most of the size fractions exhibited the following patterns on different filters: CM > QFF > GFF for NH4+; GFF > QFF > CM for SO42-; and GFF > CM > QFF for NO3-. The different patterns in coarse particles were mainly affected by filter acidity, and that in fine particles were mainly affected by hygroscopicity of the filters (especially in size fraction of 0.65-2.1 μm). Filter acidity and hygroscopicity also shifted the peaks of the annual mean size distributions of SNA on QFF from 0.43-0.65 μm on clean days to 0.65-1.1 μm on hazy days. However, this size shift was not as distinct for samples measured with CM and GFF. In addition, relative humidity (RH) and pollution levels are important factors that can enhance particulate size mode shifts of SNA on clean and hazy days. Consequently, the annual mean size distributions of SNA had maxima at 0.65-1.1 μm for QFF samples and 0.43-0.65 μm for GFF and CM samples. Compared with NH4+ and SO42-, NO3- is more sensitive to RH and pollution levels, accordingly, the annual mean size distribution of NO3- exhibited peak at 0.65-1.1 μm for CM samples instead of 0.43-0.65 μm. These methodological uncertainties should be considered when quantifying the concentrations and size distributions of SNA under different RH and haze conditions.

  6. Recovery by ultrafiltration of a commercial enzyme for cellulose hydrolysis

    SciTech Connect

    Pizzichini, M.; Fabiani, C.; Sperandei, M. )

    1991-02-01

    An enzymatic process of cellulose hydrolysis based mainly on the use of membrane techniques is under study. The proposed flow sheet assumes that during cellulose hydrolysis the enzyme is continuously separated from glucose and cellobiose and is recycled in the cellulose reaction vessel by membrane ultrafiltration. The ultrafiltration of Celluclast enzyme by Novo is performed in a DDS column module assembled with flat polysulfone membranes. Membrane polarization effects are studies in the 0.1-5% w/v enzyme concentration range under varying pressures up to 600 kPa. A partial loss of enzymatic activity is observed as a consequence of the ultrafiltration and membrane washing operations.

  7. Demonstration and Validation of a Regenerated Cellulose Dialysis Membrane Diffusion Sampler for Monitoring Ground Water Quality and Remediation Progress at DoD Sites

    DTIC Science & Technology

    2007-08-30

    with biodegradation was probably because of their longer deployment times, warmer ground-water temperatures, and proximity to high bacteria ...NFESC Naval Facilities Engineering Service Center NJDEP New Jersey Department of Environmental Protection NTU Nephelometric turbidity units PAH ...high ionic strength waters and due to biodegradation were not significant when equilibration times in wells were one to two weeks. Water samples

  8. Membrane Technology: A Search for Membranes for Submarine Atmosphere Control

    DTIC Science & Technology

    1992-01-01

    dimethyl silicone (25%) rubber membranes exhibit the highest permeability for carbon dioxide, while cellulose acetate exhibits the highest separation...factor (10.9) of carbon dioxide to oxygen. However, an immobilized film membrane (IFM) device constructed of a cellulose acetate membrane impregnated

  9. Nanofiber Ion-Exchange Membranes for the Rapid Uptake and Recovery of Heavy Metals from Water.

    PubMed

    Chitpong, Nithinart; Husson, Scott M

    2016-12-20

    An evaluation of the performance of polyelectrolyte-modified nanofiber membranes was undertaken to determine their efficacy in the rapid uptake and recovery of heavy metals from impaired waters. The membranes were prepared by grafting poly(acrylic acid) (PAA) and poly(itaconic acid) (PIA) to cellulose nanofiber mats. Performance measurements quantified the dynamic ion-exchange capacity for cadmium (Cd), productivity, and recovery of Cd(II) from the membranes by regeneration. The dynamic binding capacities of Cd(II) on both types of nanofiber membrane were independent of the linear flow velocity, with a residence time of as low as 2 s. Analysis of breakthrough curves indicated that the mass flow rate increased rapidly at constant applied pressure after membranes approached equilibrium load capacity for Cd(II), apparently due to a collapse of the polymer chains on the membrane surface, leading to an increased porosity. This mechanism is supported by hydrodynamic radius (Rh) measurements for PAA and PIA obtained from dynamic light scattering, which show that Rh values decrease upon Cd(II) binding. Volumetric productivity was high for the nanofiber membranes, and reached 0.55 mg Cd/g/min. The use of ethylenediaminetetraacetic acid as regeneration reagent was effective in fully recovering Cd(II) from the membranes. Ion-exchange capacities were constant over five cycles of binding-regeneration.

  10. Nanofiber Ion-Exchange Membranes for the Rapid Uptake and Recovery of Heavy Metals from Water

    PubMed Central

    Chitpong, Nithinart; Husson, Scott M.

    2016-01-01

    An evaluation of the performance of polyelectrolyte-modified nanofiber membranes was undertaken to determine their efficacy in the rapid uptake and recovery of heavy metals from impaired waters. The membranes were prepared by grafting poly(acrylic acid) (PAA) and poly(itaconic acid) (PIA) to cellulose nanofiber mats. Performance measurements quantified the dynamic ion-exchange capacity for cadmium (Cd), productivity, and recovery of Cd(II) from the membranes by regeneration. The dynamic binding capacities of Cd(II) on both types of nanofiber membrane were independent of the linear flow velocity, with a residence time of as low as 2 s. Analysis of breakthrough curves indicated that the mass flow rate increased rapidly at constant applied pressure after membranes approached equilibrium load capacity for Cd(II), apparently due to a collapse of the polymer chains on the membrane surface, leading to an increased porosity. This mechanism is supported by hydrodynamic radius (Rh) measurements for PAA and PIA obtained from dynamic light scattering, which show that Rh values decrease upon Cd(II) binding. Volumetric productivity was high for the nanofiber membranes, and reached 0.55 mg Cd/g/min. The use of ethylenediaminetetraacetic acid as regeneration reagent was effective in fully recovering Cd(II) from the membranes. Ion-exchange capacities were constant over five cycles of binding-regeneration. PMID:27999394

  11. Self-assembly of dermal papilla cells into inductive spheroidal microtissues on poly(ethylene-co-vinyl alcohol) membranes for hair follicle regeneration.

    PubMed

    Young, Tai-Horng; Lee, Chiao-Yun; Chiu, Hsien-Ching; Hsu, Chih-Jung; Lin, Sung-Jan

    2008-09-01

    Self-aggregation is key to hair follicle (HF) induction ability of dermal papilla (DP) cells and neogenesis of HF can be achieved by transplanting DP microtissues. However, there is currently lack of a suitable system that allows efficient production of DP microtissues and analysis of DP self-aggregation in vitro. We demonstrate that, at a higher seeding cell density, poly(ethylene-co-vinyl alcohol) (EVAL) membranes facilitate DP self-assembly into many compact spheroidal microtissues that are able to induce new HFs. This self-assembling process is associated with an enhanced cell movement and a declined cell-substrate adhesivity on EVAL. A compromised cell growth is also revealed on EVAL. On the contrary, a more adherent surface allows faster cell expansion but maintains DP cells in a flat morphology. Dynamically, cell migration, intercellular collision and intercellular adhesion contribute to DP microtissue formation on EVAL. Our results suggest that, for large-scale production of DP microtissues for HF regeneration, an adhesive surface is needed for quick cell expansion and a biomaterial with a lower adhesivity is required for self-aggregation. In addition, this system can be a model for investigation of DP self-aggregation in vitro.

  12. Promoting nerve regeneration in a neurotmesis rat model using poly(DL-lactide-ε-caprolactone) membranes and mesenchymal stem cells from the Wharton's jelly: in vitro and in vivo analysis.

    PubMed

    Pereira, T; Gärtner, A; Amorim, I; Almeida, A; Caseiro, A R; Armada-da-Silva, Paulo A S; Amado, Sandra; Fregnan, Federica; Varejão, A S P; Santos, J D; Bartolo, P J; Geuna, S; Luís, A L; Mauricio, A C

    2014-01-01

    In peripheral nerves MSCs can modulate Wallerian degeneration and the overall regenerative response by acting through paracrine mechanisms directly on regenerating axons or upon the nerve-supporting Schwann cells. In the present study, the effect of human MSCs from Wharton's jelly (HMSCs), differentiated into neuroglial-like cells associated to poly (DL-lactide-ε-caprolactone) membrane, on nerve regeneration, was evaluated in the neurotmesis injury rat sciatic nerve model. Results in vitro showed successful differentiation of HMSCs into neuroglial-like cells, characterized by expression of specific neuroglial markers confirmed by immunocytochemistry and by RT-PCR and qPCR targeting specific genes expressed. In vivo testing evaluated during the healing period of 20 weeks, showed no evident positive effect of HMSCs or neuroglial-like cell enrichment at the sciatic nerve repair site on most of the functional and nerve morphometric predictors of nerve regeneration although the nociception function was almost normal. EPT on the other hand, recovered significantly better after HMSCs enriched membrane employment, to values of residual functional impairment compared to other treated groups. When the neurotmesis injury can be surgically reconstructed with an end-to-end suture or by grafting, the addition of a PLC membrane associated with HMSCs seems to bring significant advantage, especially concerning the motor function recovery.

  13. Promoting Nerve Regeneration in a Neurotmesis Rat Model Using Poly(DL-lactide-ε-caprolactone) Membranes and Mesenchymal Stem Cells from the Wharton's Jelly: In Vitro and In Vivo Analysis

    PubMed Central

    Pereira, T.; Gärtner, A.; Amorim, I.; Almeida, A.; Caseiro, A. R.; Armada-da-Silva, Paulo A. S.; Amado, Sandra; Fregnan, Federica; Varejão, A. S. P.; Santos, J. D.; Bartolo, P. J.; Geuna, S.; Luís, A. L.; Mauricio, A. C.

    2014-01-01

    In peripheral nerves MSCs can modulate Wallerian degeneration and the overall regenerative response by acting through paracrine mechanisms directly on regenerating axons or upon the nerve-supporting Schwann cells. In the present study, the effect of human MSCs from Wharton's jelly (HMSCs), differentiated into neuroglial-like cells associated to poly (DL-lactide-ε-caprolactone) membrane, on nerve regeneration, was evaluated in the neurotmesis injury rat sciatic nerve model. Results in vitro showed successful differentiation of HMSCs into neuroglial-like cells, characterized by expression of specific neuroglial markers confirmed by immunocytochemistry and by RT-PCR and qPCR targeting specific genes expressed. In vivo testing evaluated during the healing period of 20 weeks, showed no evident positive effect of HMSCs or neuroglial-like cell enrichment at the sciatic nerve repair site on most of the functional and nerve morphometric predictors of nerve regeneration although the nociception function was almost normal. EPT on the other hand, recovered significantly better after HMSCs enriched membrane employment, to values of residual functional impairment compared to other treated groups. When the neurotmesis injury can be surgically reconstructed with an end-to-end suture or by grafting, the addition of a PLC membrane associated with HMSCs seems to bring significant advantage, especially concerning the motor function recovery. PMID:25121094

  14. Cellulose Insulation

    NASA Technical Reports Server (NTRS)

    1980-01-01

    Fire retardant cellulose insulation is produced by shredding old newspapers and treating them with a combination of chemicals. Insulating material is blown into walls and attics to form a fiber layer which blocks the flow of air. All-Weather Insulation's founders asked NASA/UK-TAP to help. They wanted to know what chemicals added to newspaper would produce an insulating material capable of meeting federal specifications. TAP researched the query and furnished extensive information. The information contributed to successful development of the product and helped launch a small business enterprise which is now growing rapidly.

  15. Method of forming an electrically conductive cellulose composite

    DOEpatents

    Evans, Barbara R [Oak Ridge, TN; O'Neill, Hugh M [Knoxville, TN; Woodward, Jonathan [Ashtead, GB

    2011-11-22

    An electrically conductive cellulose composite includes a cellulose matrix and an electrically conductive carbonaceous material incorporated into the cellulose matrix. The electrical conductivity of the cellulose composite is at least 10 .mu.S/cm at 25.degree. C. The composite can be made by incorporating the electrically conductive carbonaceous material into a culture medium with a cellulose-producing organism, such as Gluconoacetobacter hansenii. The composites can be used to form electrodes, such as for use in membrane electrode assemblies for fuel cells.

  16. The productive cellulase binding capacity of cellulosic substrates.

    PubMed

    Karuna, Nardrapee; Jeoh, Tina

    2017-03-01

    Cellulosic biomass is the most promising feedstock for renewable biofuel production; however, the mechanisms of the heterogeneous cellulose saccharification reaction are still unsolved. As cellulases need to bind isolated molecules of cellulose at the surface of insoluble cellulose fibrils or larger aggregated cellulose structures in order to hydrolyze glycosidic bonds, the "accessibility of cellulose to cellulases" is considered to be a reaction limiting property of cellulose. We have defined the accessibility of cellulose to cellulases as the productive binding capacity of cellulose, that is, the concentration of productive binding sites on cellulose that are accessible for binding and hydrolysis by cellulases. Productive cellulase binding to cellulose results in hydrolysis and can be quantified by measuring hydrolysis rates. In this study, we measured the productive Trichoderma reesei Cel7A (TrCel7A) binding capacity of five cellulosic substrates from different sources and processing histories. Swollen filter paper and bacterial cellulose had higher productive binding capacities of ∼6 µmol/g while filter paper, microcrystalline cellulose, and algal cellulose had lower productive binding capacities of ∼3 µmol/g. Swelling and regenerating filter paper using phosphoric acid increased the initial accessibility of the reducing ends to TrCel7A from 4 to 6 µmol/g. Moreover, this increase in initial productive binding capacity accounted in large part for the difference in the overall digestibility between filter paper and swollen filter paper. We further demonstrated that an understanding of how the productive binding capacity declines over the course of the hydrolysis reaction has the potential to predict overall saccharification time courses. Biotechnol. Bioeng. 2017;114: 533-542. © 2016 Wiley Periodicals, Inc.

  17. Regeneration inducers in limb regeneration.

    PubMed

    Satoh, Akira; Mitogawa, Kazumasa; Makanae, Aki

    2015-08-01

    Limb regeneration ability, which can be observed in amphibians, has been investigated as a representative phenomenon of organ regeneration. Recently, an alternative experimental system called the accessory limb model was developed to investigate early regulation of amphibian limb regeneration. The accessory limb model contributed to identification of limb regeneration inducers in urodele amphibians. Furthermore, the accessory limb model may be applied to other species to explore universality of regeneration mechanisms. This review aims to connect the insights recently gained to emboss universality of regeneration mechanisms among species. The defined molecules (BMP7 (or2) + FGF2 + FGF8) can transform skin wound healing to organ (limb) regeneration responses. The same molecules can initiate regeneration responses in some species.

  18. Microwave-assisted pretreatment of cellulose in ionic liquid for accelerated enzymatic hydrolysis.

    PubMed

    Ha, Sung Ho; Mai, Ngoc Lan; An, Gwangmin; Koo, Yoon-Mo

    2011-01-01

    For increasing cellulose accessibility to the enzymatic attack, the pretreatment is a necessary step to alter some structural characteristics of cellulosic materials. As a new pretreatment method, microwave irradiation on cellulose dissolution pretreatment with ionic liquids (ILs) was investigated in this study. Microwave irradiation not only enhanced the solubility of cellulose in ILs but also significantly decreased the degree of polymerization of regenerated cellulose after IL dissolution pretreatment, resulting in significant improvement of cellulose hydrolysis. The rate of enzymatic hydrolysis of cotton cellulose was increased by at least 12-fold after IL dissolution pretreatment at 110 °C and by 50-fold after IL dissolution pretreatment with microwave irradiation. Our results demonstrate that cellulose pretreatment with ILs and microwave irradiation is a potential alternative method for the pretreatment of cellulosic materials.

  19. Membrane surface engineering for protein separations: experiments and simulations.

    PubMed

    Liu, Zizhao; Du, Hongbo; Wickramasinghe, S Ranil; Qian, Xianghong

    2014-09-09

    A bisphosphonate derived ligand was successfully synthesized and grafted from the surface of regenerated cellulose membrane using atom transfer radical polymerization (ATRP) for protein separations. This ligand has a remarkable affinity for arginine (Arg) residues on protein surface. Hydrophilic residues N-(2-hydroxypropyl) methacrylamide (HPMA) was copolymerized to enhance the flexibility of the copolymer ligand and further improve specific protein adsorption. The polymerization of bisphosphonate derivatives was successful for the first time using ATRP. Static and dynamic binding capacities were determined for binding and elution of Arg rich lysozyme. The interaction mechanism between the copolymer ligand and lysozyme was elucidated using classical molecular dynamics (MD) simulations.

  20. Blood-filled spaces with and without deproteinized bone grafts in guided bone regeneration. A histomorphometric study of the rabbit skull using non-resorbable membrane.

    PubMed

    Okazaki, Kousuke; Shimizu, Yoshinaka; Xu, Hui; Ooya, Kiyoshi

    2005-04-01

    This experimental study evaluated the effects of deproteinized bone grafts on guided bone regeneration (GBR). A groove was made in the bone marrow of the external cortical plate of the skull. A dome of non-resorbable membrane was placed on the groove and secured with titanium pins. The secluded graft space was filled with autogenous blood clots (control group) and deproteinized bone particles (experimental group). The rabbits were sacrificed 2, 4, 8 and 12 weeks after the operation. Decalcified and paraffin-embedded, transverse 3-mum-thick sections were made and stained with hematoxylin and eosin. The proportions of newly formed bone and newly formed bone-graft particle contact surfaces were histomorphometrically measured in the basal, central, and peripheral areas from the cortical plate to the top of the dome. In the control group, the basal area showed a significant increase at 4 weeks (P<0.01) and a significant decrease at 8 weeks (P<0.01). The central and peripheral areas showed gradual increases in the proportion of newly formed bone. The experimental group showed significant increase at 4 weeks in the basal area and at 8 weeks in central and peripheral area (P<0.01). There were significant differences between both groups in basal and central area (P<0.01). The proportion of newly formed bone-graft particle contact length showed significant increases at 4 weeks (P<0.01) and no significant decreases at 8 and 12 weeks in three areas. The present study showed that deproteinized bone grafts maintain newly formed bone in extensive areas for a prolonged period during GBR.

  1. TECHNICAL NOTE: Electrically aligned cellulose film for electro-active paper and its piezoelectricity

    NASA Astrophysics Data System (ADS)

    Yun, Sungryul; Jang, Sangdong; Yun, Gyu-Young; Kim, Jaehwan

    2009-11-01

    Electrically aligned regenerated cellulose films were fabricated and the effect of applied electric field was investigated for the piezoelectricity of electro-active paper (EAPap). The EAPap was fabricated by coating gold electrodes on both sides of regenerated cellulose film. The cellulose film was prepared by dissolving cotton pulp in LiCl/N,N-dimethylacetamide solution followed by a cellulose chain regeneration process. During the regeneration process an external electric field was applied in the direction of mechanical stretching. Alignment of cellulose fiber chains was investigated as a function of applied electric field. The material characteristics of the cellulose films were analyzed by using an x-ray diffractometer, a field emission scanning electron microscope and a high voltage electron microscope. The application of external electric fields was found to induce formation of nanofibers in the cellulose, resulting in an increase in the crystallinity index (CI) values. It was also found that samples with higher CI values showed higher in-plane piezoelectric constant, d31, values. The piezoelectricity of the current EAPap films was measured to be equivalent or better than that of ordinary PVDF films. Therefore, an external electric field applied to a cellulose film along with a mechanical stretching during the regeneration process can enhance the piezoelectricity.

  2. The Properties of Water in Polymeric Membranes.

    DTIC Science & Technology

    The relative amounts of freezing and non-freezing water in various water-wet cellulose acetate (CA) membranes have been determined by NMR techniques...by reverse osmosis is compared to that of the commonly used cellulose acetate .

  3. A new route to improved glucose yields in cellulose hydrolysis

    SciTech Connect

    Zhao, Haibo; Holladay, John E.; Kwak, Ja Hun; Zhang, Z. Conrad

    2007-08-01

    An unusual inverse temperature-dependent pathway was discovered for cellulose decrystallization in trifluoroacetic acid (TFA). Cellulose was completely decrystallized by TFA at 0 °C in less than 2 hours, a result not achieved in 48 hours at 25°C in the same medium. The majority of TFA used in cellulose decrystallization was recycled via a vacuum process. The small remaining amount of TFA was diluted with water to make a 0.5% TFA solution and used as a catalyst in dilute acid hydrolysis. After one minute, under batch conditions at 185 °C, the glucose yield reached 63.5% without production of levulinic acid. In comparison, only 15.0% glucose yield was achieved in the hydrolysis of untreated cellulose by 0.5% H2SO4 under the same condition. Further improvement of glucose yield is possible by optimizing reaction conditions. Alternatively, the remaining TFA can be completely removed by water while keeping the regenerated cellulose in a highly amorphous state. This regenerated cellulose is much more reactive than untreated cellulose in hydrolysis reactions, but still less reactive than corn starch. The lower temperatures and shorter reaction times with this activated cellulose makes it possible to reduce operating costs and decrease byproduct yields such as HMF and levulinic acid.

  4. Purification of triacylglycerols for biodiesel production from Nannochloropsis microalgae by membrane technology.

    PubMed

    Giorno, Filomena; Mazzei, Rosalinda; Giorno, Lidietta

    2013-07-01

    Triacylglycerols recovery from wet microalgae is a key aspect of biodiesel production, because of the energetic balance gained from avoiding biomass drying. In order to isolate TAG from Nannochloropsis cells, the possibility to concentrate biomass and to recover TAG in a single step by membrane process was studied. Different polymeric membranes were selected and screened on the basis of adsorption test and permeation flux. Results showed that membrane of regenerated cellulose (RC) with nominal molecular weight cutoff of 100 kDa and 30 kDa gave the best performance. Indeed, permeate flux was stable during ultrafiltration experiment in concentration mode and no severe fouling/cake deposition was observed. Both membranes allowed to recover permeates with high content of triacylglicerols. However, a more purity of the triacylglicerols from the other co-products was only obtained with the 30 kDa RC membrane because the retention of the unwanted proteins was in the range of 89%.

  5. Bioelectricity and epimorphic regeneration.

    PubMed

    Stewart, Scott; Rojas-Muñoz, Agustin; Izpisúa Belmonte, Juan Carlos

    2007-11-01

    All cells have electric potentials across their membranes, but is there really compelling evidence to think that such potentials are used as instructional cues in developmental biology? Numerous reports indicate that, in fact, steady, weak bioelectric fields are observed throughout biology and function during diverse biological processes, including development. Bioelectric fields, generated upon amputation, are also likely to play a key role during vertebrate regeneration by providing the instructive cues needed to direct migrating cells to form a wound epithelium, a structure unique to regenerating animals. However, mechanistic insight is still sorely lacking in the field. What are the genes required for bioelectric-dependent cell migration during regeneration? The power of genetics combined with the use of zebrafish offers the best opportunity for unbiased identification of the molecular players in bioelectricity.

  6. Characterization of cellulose extracted from oil palm empty fruit bunch

    NASA Astrophysics Data System (ADS)

    Sisak, Muhammad Asri Abdul; Daik, Rusli; Ramli, Suria

    2015-09-01

    Recently, cellulose has been studied by many researchers due to its promising properties such as biodegradability, biocompatibility, hydrophilicity and robustness. Due to that it is applied in many fields such as paper, film, drug delivery, membranes, etc. Cellulose can be extracted from various plants while oil palm empty fruit bunch (OPEFB) is the one of its sources. In this study, cellulose was extracted by chemical treatments which involved the use of formic acid and hydrogen peroxide to remove hemicellulose and lignin components. Maximum yield was 43.22%. Based on the FT-IR spectra, the peak of wax (1735 cm-1), hemicellulose (1375 cm-1) and lignin (1248 cm-1 and 1037 cm-1) were not observed in extracted cellulose. TGA analysis showed that the extracted cellulose starts to thermally degrade at 340 °C. The SEM analysis suggested that the cellulose extracted from OPEFB was not much different from commercial cellulose.

  7. A Study of Bonding Cellulose Acetate to Polyarylsulfone,

    DTIC Science & Technology

    The objective of this study was to develop a method by which ultrathin films (500 to 1500 angstroms in thickness) of cellulose acetate could be...rejecting and flow characteristics of the cellulose acetate -polysulfone composite. A successful method was found to be the application of a dilute...solution (1.5 percent by weight) of Resyn 26-2404 to the polysulfone before casting the cellulose acetate membrane. A TYPICAL COMPOSITE WITH A SPRAYED

  8. Alveolar bone regeneration using poly-(lactic acid-co-glycolic acid-co-ε-caprolactone) porous membrane with collagen sponge containing basic fibroblast growth factor: an experimental study in the dog.

    PubMed

    Matsumoto, Goichi; Hoshino, Jyunichi; Kinoshita, Yasuhiko; Sugita, Yoshihiko; Kubo, Katsutoshi; Maeda, Hatsuhiko; Ikada, Yoshito; Kinoshita, Yukihiko

    2012-11-01

    The aim of this study was to evaluate the effects of combining porous poly-lactic acid-co-glycolic acid-co-ε-caprolactone (PLGC) as a barrier membrane and collagen sponge containing basic fibroblast growth factor (bFGF) to promote bone regeneration in the canine mandible. In six beagle dogs, two lateral bone defects per side were created in the mandible. The lateral bone defects on the left side were treated with a PLGC membrane plus a collagen sponge containing bFGF. In half of these, the collagen sponge contained 50 µg of bFGF. In the other half, it contained 250 µg of bFGF. As a control, we treated the right-side bone defects in each animal with the same PLGC membrane but with a collagen sponge containing phosphate buffered saline. Computed tomography (CT) images were recorded at 3 and 6 months post-op to evaluate regeneration of the bone defects. After a healing period of 6 months, whole mandibles were removed for micro-CT and histological analyses. The post-op CT images showed that more bone had formed at all experimental sites than at control sites. At 3 months post-op, the volume of bone at defect sites covered with PLGC membrane plus 250 µg of bFGF was significantly greater than it was at defect sites covered with PLGC membrane plus 50 µg of bFGF. At 6 months post-op, however, this difference was smaller and not statistically significant. Micro-CT measurement showed that the volume of new bone regenerated at bone-defect sites, covered with PLGC membrane plus bFGF, was significantly greater than that of control sites. However, the presence or absence of bFGF in the collagen sponge did not significantly affect the bone density of new bone. These results suggest that the macroporous bioresorbable PLGC membrane plus collagen sponge containing bFGF effectively facilitates healing in GBR procedures.

  9. Evaluation of Pyrrones as Membranes.

    DTIC Science & Technology

    1970-09-01

    The data indicate comparable flux values and superior water-to-salt permeabilities of the Pyrrones relative to symmetric cellulose acetate membranes...could lead to substantial improvements over asymmetric cellulose acetate , from which the best reverse osmosis membranes are currently prepared.

  10. Application of tetra-n-methylammonium hydroxide on cellulose dissolution and isolation from sugarcane bagasse.

    PubMed

    Zhong, Chao; Wang, Chunming; Wang, Fengxue; Jia, Honghua; Wei, Ping; Zhao, Yin

    2016-01-20

    Cellulose isolation, a promising way for lignocellulosic biomass utilization, is always restricted by the poor solubility of cellulose. In this paper, tetra-n-methylammonium hydroxide (TMAH) was confirmed to be capable of readily dissolving/regenerating cellulose without chemical modification at room temperature. Meanwhile, cellulose isolation from lignocellulosic biomass by initially dissolving the biomass in TMAH followed by cellulose precipitation was proposed, and the isolated substance with average cellulose purity of 92.1 ± 0.3% could be obtained throughout this process under the optimum conditions: temperature 52 °C, time 60 min, and loading ratio of TMAH/biomass (w/w) 7.2:1. Besides, high efficiency cellulose isolation (i.e. >70% cellulose purity) could be continuously remained during 4-round cycles by using the recycled TMAH solvent without distinct activity loss.

  11. Efficient production of glucose by microwave-assisted acid hydrolysis of cellulose hydrogel.

    PubMed

    Sun, Binzhe; Duan, Lian; Peng, Gege; Li, Xiaoxia; Xu, Aihua

    2015-09-01

    To improve the production of glucose from cellulose, a simple and effective route was developed. This process uses a combination of a step of cellulose dissolution in aqueous NaOH/urea solution and then regeneration with water, followed by an acid hydrolysis step under microwave irradiation. The method is effective to obtain glucose from α-cellulose, microcrystalline cellulose, filter paper, ramie fiber and absorbent cotton. Increased with the acid concentration the glucose yield from hydrogel hydrolysis increased from 0.42% to 44.6% at 160 °C for 10 min. Moreover, the ozone treatment of cellulose in NaOH/urea solution before regeneration significantly enhanced the hydrolysis efficiency with a glucose yield of 59.1%. It is believed that the chains in cellulose hydrogel are relatively free approached, making that the acids easily access the β-glycosidic bonds.

  12. Hybrid nanocomposite based on cellulose and tin oxide: growth, structure, tensile and electrical characteristics

    NASA Astrophysics Data System (ADS)

    Mahadeva, Suresha K.; Kim, Jaehwan

    2011-10-01

    A highly flexible nanocomposite was developed by coating a regenerated cellulose film with a thin layer of tin oxide (SnO2) by liquid-phase deposition. Tin oxide was crystallized in solution and formed nanocrystal coatings on regenerated cellulose. The nanocrystalline layers did not exfoliate from cellulose. Transmission electron microscopy and energy dispersive x-ray spectroscopy suggest that SnO2 was not only deposited over the cellulose surface, but also nucleated and grew inside the cellulose film. Current-voltage characteristics of the nanocomposite revealed that its electrical resistivity decreases with deposition time, with the lowest value obtained for 24 h of deposition. The cellulose-SnO2 hybrid nanocomposite can be used for biodegradable and disposable chemical, humidity and biosensors.

  13. Simulations of cellulose translocation in the bacterial cellulose synthase suggest a regulatory mechanism for the dimeric structure of cellulose

    PubMed Central

    Knott, Brandon C.; Crowley, Michael F.; Himmel, Michael E.; Zimmer, Jochen; Beckham, Gregg T.

    2016-01-01

    The processive cycle of the bacterial cellulose synthase (Bcs) includes the addition of a single glucose moiety to the end of a growing cellulose chain followed by the translocation of the nascent chain across the plasma membrane. The mechanism of this translocation and its precise location within the processive cycle are not well understood. In particular, the molecular details of how a polymer (cellulose) whose basic structural unit is a dimer (cellobiose) can be constructed by adding one monomer (glucose) at a time are yet to be elucidated. Here, we have utilized molecular dynamics simulations and free energy calculations to the shed light on these questions. We find that translocation forward by one glucose unit is quite favorable energetically, giving a free energy stabilization of greater than 10 kcal/mol. In addition, there is only a small barrier to translocation, implying that translocation is not rate limiting within the Bcs processive cycle (given experimental rates for cellulose synthesis in vitro). Perhaps most significantly, our results also indicate that steric constraints at the transmembrane tunnel entrance regulate the dimeric structure of cellulose. Namely, when a glucose molecule is added to the cellulose chain in the same orientation as the acceptor glucose, the terminal glucose freely rotates upon forward motion, thus suggesting a regulatory mechanism for the dimeric structure of cellulose. We characterize both the conserved and non-conserved enzyme-polysaccharide interactions that drive translocation, and find that 20 of the 25 residues that strongly interact with the translocating cellulose chain in the simulations are well conserved, mostly with polar or aromatic side chains. Our results also allow for a dynamical analysis of the role of the so-called `finger helix' in cellulose translocation that has been observed structurally. Taken together, these findings aid in the elucidation of the translocation steps of the Bcs processive cycle and

  14. Simulations of cellulose translocation in the bacterial cellulose synthase suggest a regulatory mechanism for the dimeric structure of cellulose.

    PubMed

    Knott, Brandon C; Crowley, Michael F; Himmel, Michael E; Zimmer, Jochen; Beckham, Gregg T

    2016-05-01

    The processive cycle of the bacterial cellulose synthase (Bcs) includes the addition of a single glucose moiety to the end of a growing cellulose chain followed by the translocation of the nascent chain across the plasma membrane. The mechanism of this translocation and its precise location within the processive cycle are not well understood. In particular, the molecular details of how a polymer (cellulose) whose basic structural unit is a dimer (cellobiose) can be constructed by adding one monomer (glucose) at a time are yet to be elucidated. Here, we have utilized molecular dynamics simulations and free energy calculations to the shed light on these questions. We find that translocation forward by one glucose unit is quite favorable energetically, giving a free energy stabilization of greater than 10 kcal/mol. In addition, there is only a small barrier to translocation, implying that translocation is not rate limiting within the Bcs processive cycle (given experimental rates for cellulose synthesis in vitro). Perhaps most significantly, our results also indicate that steric constraints at the transmembrane tunnel entrance regulate the dimeric structure of cellulose. Namely, when a glucose molecule is added to the cellulose chain in the same orientation as the acceptor glucose, the terminal glucose freely rotates upon forward motion, thus suggesting a regulatory mechanism for the dimeric structure of cellulose. We characterize both the conserved and non-conserved enzyme-polysaccharide interactions that drive translocation, and find that 20 of the 25 residues that strongly interact with the translocating cellulose chain in the simulations are well conserved, mostly with polar or aromatic side chains. Our results also allow for a dynamical analysis of the role of the so-called `finger helix' in cellulose translocation that has been observed structurally. Taken together, these findings aid in the elucidation of the translocation steps of the Bcs processive cycle and

  15. Simulations of cellulose translocation in the bacterial cellulose synthase suggest a regulatory mechanism for the dimeric structure of cellulose

    SciTech Connect

    Knott, Brandon C.; Crowley, Michael F.; Himmel, Michael E.; Zimmer, Jochen; Beckham, Gregg T.

    2016-01-29

    The processive cycle of the bacterial cellulose synthase (Bcs) includes the addition of a single glucose moiety to the end of a growing cellulose chain followed by the translocation of the nascent chain across the plasma membrane. The mechanism of this translocation and its precise location within the processive cycle are not well understood. In particular, the molecular details of how a polymer (cellulose) whose basic structural unit is a dimer (cellobiose) can be constructed by adding one monomer (glucose) at a time are yet to be elucidated. Here, we have utilized molecular dynamics simulations and free energy calculations to the shed light on these questions. We find that translocation forward by one glucose unit is quite favorable energetically, giving a free energy stabilization of greater than 10 kcal mol-1. In addition, there is only a small barrier to translocation, implying that translocation is not rate limiting within the Bcs processive cycle (given experimental rates for cellulose synthesis in vitro). Perhaps most significantly, our results also indicate that steric constraints at the transmembrane tunnel entrance regulate the dimeric structure of cellulose. Namely, when a glucose molecule is added to the cellulose chain in the same orientation as the acceptor glucose, the terminal glucose freely rotates upon forward motion, thus suggesting a regulatory mechanism for the dimeric structure of cellulose. We characterize both the conserved and non-conserved enzyme-polysaccharide interactions that drive translocation, and find that 20 of the 25 residues that strongly interact with the translocating cellulose chain in the simulations are well conserved, mostly with polar or aromatic side chains. Our results also allow for a dynamical analysis of the role of the so-called 'finger helix' in cellulose translocation that has been observed structurally. Taken together, these findings aid in the elucidation of the translocation steps of the Bcs processive cycle

  16. Simulations of cellulose translocation in the bacterial cellulose synthase suggest a regulatory mechanism for the dimeric structure of cellulose

    DOE PAGES

    Knott, Brandon C.; Crowley, Michael F.; Himmel, Michael E.; ...

    2016-01-29

    The processive cycle of the bacterial cellulose synthase (Bcs) includes the addition of a single glucose moiety to the end of a growing cellulose chain followed by the translocation of the nascent chain across the plasma membrane. The mechanism of this translocation and its precise location within the processive cycle are not well understood. In particular, the molecular details of how a polymer (cellulose) whose basic structural unit is a dimer (cellobiose) can be constructed by adding one monomer (glucose) at a time are yet to be elucidated. Here, we have utilized molecular dynamics simulations and free energy calculations tomore » the shed light on these questions. We find that translocation forward by one glucose unit is quite favorable energetically, giving a free energy stabilization of greater than 10 kcal mol-1. In addition, there is only a small barrier to translocation, implying that translocation is not rate limiting within the Bcs processive cycle (given experimental rates for cellulose synthesis in vitro). Perhaps most significantly, our results also indicate that steric constraints at the transmembrane tunnel entrance regulate the dimeric structure of cellulose. Namely, when a glucose molecule is added to the cellulose chain in the same orientation as the acceptor glucose, the terminal glucose freely rotates upon forward motion, thus suggesting a regulatory mechanism for the dimeric structure of cellulose. We characterize both the conserved and non-conserved enzyme-polysaccharide interactions that drive translocation, and find that 20 of the 25 residues that strongly interact with the translocating cellulose chain in the simulations are well conserved, mostly with polar or aromatic side chains. Our results also allow for a dynamical analysis of the role of the so-called 'finger helix' in cellulose translocation that has been observed structurally. Taken together, these findings aid in the elucidation of the translocation steps of the Bcs processive

  17. An assembled poly-4-vinyl pyridine and cellulose triacetate membrane and Bi2S3 electrode for photoelectrochemical diffusion of metallic ions.

    PubMed

    Amara, Mourad; Arous, Omar; Smail, Fatima; Kerdjoudj, Hacène; Trari, Mohamed; Bouguelia, Aissa

    2009-09-30

    The transport phenomena across ion exchange membrane may be enhanced by applying various strengths inside or outside the system. The electrical current, generated by n-type semiconductor, is used to catalyse the separation of metal ions. The cation exchange membrane located between the two compartments allows both the separation and concentration of M(n+) (Ag(+), Cu(2+), Pb(2+) and Ni(2+)). The flows of M(n+) from the aqueous solution to-and inside the membrane are monitored by the determination of the fluxes and the potentials. In this study, the four cations are investigated alone or in quaternary systems. From photoelectrochemical measurement, the gap of Bi(2)S(3) is found to be indirect at 1.65 eV. The shape of photocurrent potential curve and the negative flat band potential (-1.02 V(SCE)) give evidence of n-type character. The conduction band (-1.25 V(SCE)) yields thermodynamically M(2+) photoreduction and catalyzes the diffusion process. The photoelectrode Bi(2)S(3) makes the flux twofold greater than that observed in the dark. In all cases, the potential of the electrode M(2+)/M in the feed compartment increases until a maximal value, reached at approximately 100 min above which it undergoes a diminution. The membrane is more selective to Cu(2+) and this selectivity decreases in the quaternary system.

  18. Use of poly(DL-lactide-ε-caprolactone) membranes and mesenchymal stem cells from the Wharton's jelly of the umbilical cord for promoting nerve regeneration in axonotmesis: in vitro and in vivo analysis.

    PubMed

    Gärtner, A; Pereira, T; Alves, Marco G; Armada-da-Silva, P A S; Amorim, I; Gomes, R; Ribeiro, J; França, M L; Lopes, C; Carvalho, Rui A; Socorro, S; Oliveira, Pedro F; Porto, B; Sousa, R; Bombaci, A; Ronchi, G; Fregnan, F; Varejão, A S P; Luís, A L; Geuna, S; Maurício, A C

    2012-12-01

    Cellular systems implanted into an injured nerve may produce growth factors or extracellular matrix molecules, modulate the inflammatory process and eventually improve nerve regeneration. In the present study, we evaluated the therapeutic value of human umbilical cord matrix MSCs (HMSCs) on rat sciatic nerve after axonotmesis injury associated to Vivosorb® membrane. During HMSCs expansion and differentiation in neuroglial-like cells, the culture medium was collected at 48, 72 and 96 h for nuclear magnetic resonance (NMR) analysis in order to evaluate the metabolic profile. To correlate the HMSCs ability to differentiate and survival capacity in the presence of the Vivosorb® membrane, the [Ca(2+)]i of undifferentiated HMSCs or neuroglial-differentiated HMSCs was determined by the epifluorescence technique using the Fura-2AM probe. The Vivosorb® membrane proved to be adequate and used as scaffold associated with undifferentiated HMSCs or neuroglial-differentiated HMSCs. In vivo testing was carried out in adult rats where a sciatic nerve axonotmesis injury was treated with undifferentiated HMSCs or neuroglial differentiated HMSCs with or without the Vivosorb® membrane. Motor and sensory functional recovery was evaluated throughout a healing period of 12 weeks using sciatic functional index (SFI), extensor postural thrust (EPT), and withdrawal reflex latency (WRL). Stereological analysis was carried out on regenerated nerve fibers. In vitro investigation showed the formation of typical neuroglial cells after differentiation, which were positively stained for the typical specific neuroglial markers such as the GFAP, the GAP-43 and NeuN. NMR showed clear evidence that HMSCs expansion is glycolysis-dependent but their differentiation requires the switch of the metabolic profile to oxidative metabolism. In vivo studies showed enhanced recovery of motor and sensory function in animals treated with transplanted undifferentiated and differentiated HMSCs that was

  19. Recent progress in cellulose nanocrystals: sources and production.

    PubMed

    Trache, Djalal; Hussin, M Hazwan; Haafiz, M K Mohamad; Thakur, Vijay Kumar

    2017-02-02

    Cellulose nanocrystals, a class of fascinating bio-based nanoscale materials, have received a tremendous amount of interest both in industry and academia owing to its unique structural features and impressive physicochemical properties such as biocompatibility, biodegradability, renewability, low density, adaptable surface chemistry, optical transparency, and improved mechanical properties. This nanomaterial is a promising candidate for applications in fields such as biomedical, pharmaceuticals, electronics, barrier films, nanocomposites, membranes, supercapacitors, etc. New resources, new extraction procedures, and new treatments are currently under development to satisfy the increasing demand of manufacturing new types of cellulose nanocrystals-based materials on an industrial scale. Therefore, this review addresses the recent progress in the production methodologies of cellulose nanocrystals, covering principal cellulose resources and the main processes used for its isolation. A critical and analytical examination of the shortcomings of various approaches employed so far is made. Additionally, structural organization of cellulose and nomenclature of cellulose nanomaterials have also been discussed for beginners in this field.

  20. Development of a novel pH sensor based upon Janus Green B immobilized on triacetyl cellulose membrane: Experimental design and optimization.

    PubMed

    Chamkouri, Narges; Niazi, Ali; Zare-Shahabadi, Vali

    2016-03-05

    A novel pH optical sensor was prepared by immobilizing an azo dye called Janus Green B on the triacetylcellulose membrane. Condition of the dye solution used in the immobilization step, including concentration of the dye, pH, and duration were considered and optimized using the Box-Behnken design. The proposed sensor showed good behavior and precision (RSD<5%) in the pH range of 2.0-10.0. Advantages of this optical sensor include on-line applicability, no leakage, long-term stability (more than 6 months), fast response time (less than 1 min), high selectivity and sensitivity as well as good reversibility and reproducibility.

  1. Development of a novel pH sensor based upon Janus Green B immobilized on triacetyl cellulose membrane: Experimental design and optimization

    NASA Astrophysics Data System (ADS)

    Chamkouri, Narges; Niazi, Ali; Zare-Shahabadi, Vali

    2016-03-01

    A novel pH optical sensor was prepared by immobilizing an azo dye called Janus Green B on the triacetylcellulose membrane. Condition of the dye solution used in the immobilization step, including concentration of the dye, pH, and duration were considered and optimized using the Box-Behnken design. The proposed sensor showed good behavior and precision (RSD < 5%) in the pH range of 2.0-10.0. Advantages of this optical sensor include on-line applicability, no leakage, long-term stability (more than 6 months), fast response time (less than 1 min), high selectivity and sensitivity as well as good reversibility and reproducibility.

  2. Dissolution of cellulose from AFEX-pretreated Zoysia japonica in AMIMCl with ultrasonic vibration.

    PubMed

    Liu, Le; Ju, Meiting; Li, Weizun; Hou, Qidong

    2013-10-15

    In this study, 1-allyl-3-methylimidazolium chloride (AMIMCl), an ionic liquid, was synthesized and characterized by a series of test methods. Pretreatment of Zoysia japonica by ammonia fiber expansion (AFEX) was shown to reduce significantly the mass of hemicellulose and lignin in biomass, thereby breaking the lignocellulosic structure. Z. japonica samples pretreated with AFEX showed reasonable solubility in AMIMCl upon ultrasonic treatment. The rate of cellulose regeneration from Z. japonica samples pretreated with AFEX increased with increase in applied power of ultrasonication within a certain power range from 0 to 110 W. The regeneration rate of cellulose from AFEX-pretreated Z. japonica reached a maximum of 97% when the ultrasonic power was 110 W. Fourier transform infrared spectroscopy and nuclear magnetic resonance analyses indicated that the regenerated cellulose was similar to microcrystalline cellulose.

  3. Cellulose-Microtubule Uncoupling Proteins Prevent Lateral Displacement of Microtubules during Cellulose Synthesis in Arabidopsis.

    PubMed

    Liu, Zengyu; Schneider, Rene; Kesten, Christopher; Zhang, Yi; Somssich, Marc; Zhang, Youjun; Fernie, Alisdair R; Persson, Staffan

    2016-08-08

    Cellulose is the most abundant biopolymer on Earth and is the major contributor to plant morphogenesis. Cellulose is synthesized by plasma membrane-localized cellulose synthase complexes (CSCs). Nascent cellulose microfibrils become entangled in the cell wall, and further catalysis therefore drives the CSC forward through the membrane: a process guided by cortical microtubules via the protein CSI1/POM2. Still, it is unclear how the microtubules can withstand the forces generated by the motile CSCs to effectively direct CSC movement. Here, we identified a family of microtubule-associated proteins, the cellulose synthase-microtubule uncouplings (CMUs), that located as static puncta along cortical microtubules. Functional disruption of the CMUs caused lateral microtubule displacement and compromised microtubule-based guidance of CSC movement. CSCs that traversed the microtubules interacted with the microtubules via CSI1/POM2, which prompted the lateral microtubule displacement. Hence, we have revealed how microtubules can withstand the propulsion of the CSCs during cellulose biosynthesis and thus sustain anisotropic plant cell growth.

  4. Magnetic and electric field alignments of cellulose chains for electro-active paper actuator

    NASA Astrophysics Data System (ADS)

    Yun, Sungryul; Chen, Yi; Lee, Sang Woo; Kim, Jaehwan; Kim, Heung Soo

    2008-03-01

    To improve the piezoelectricity of cellulose electro-active paper (EAPap), electrical field and magnetic field alignments were investigated. EAPap is made with cellulose by dissolving cotton pulp and regenerating cellulose with aligned cellulose fibers. EAPap made with cellulose has piezoelectric property due to its structural crystallinity. Noncentro-symmetric crystal structure of EAPap, which is mostly cellulose II, can exhibit piezoelectricity. However, EAPap has ordered crystal parts as well as disordered parts of cellulose. Thus, well alignment of cellulose chains in EAPap is important to improve its piezoelectricity. In this paper, uniaxial alignments of cellulose chains were investigated by applying electric field and magnetic field. As exposing different fields to EAPap samples, the changed characteristics were analyzed by X-Ray diffractometer (XRD) and Scanning electron microscopy (SEM). Finally, the piezoelectricity of EAPap samples was evaluated by comparing their piezoelectric charge constant [d 31]. As increasing applied electric field up to 40V/mm, d 31 value was gradually improved due to increased cellulose crystallinity as well as alignment of cellulose chains. Also the alignment of cellulose chains was improved with increasing the exposing time to magnetic field (5.3T) and well alignment was achieved by exposing EAPap sample on the magnetic field for 180min.

  5. Pea Xyloglucan and Cellulose

    PubMed Central

    Hayashi, Takahisa; Marsden, Margery P. F.; Delmer, Deborah P.

    1987-01-01

    Since xyloglucan is believed to bind to cellulose microfibrils in the primary cell walls of higher plants and, when isolated from the walls, can also bind to cellulose in vitro, the binding mechanism of xyloglucan to cellulose was further investigated using radioiodinated pea xyloglucan. A time course for the binding showed that the radioiodinated xyloglucan continued to be bound for at least 4 hours at 40°C. Binding was inhibited above pH 6. Binding capacity was shown to vary for celluloses of different origin and was directly related to the relative surface area of the microfibrils. The binding of xyloglucan to cellulose was very specific and was not affected by the presence of a 10-fold excess of (1→2)-β-glucan, (1→3)-β-glucan, (1→6)-β-glucan, (1→3, 1→4)-β-glucan, arabinogalactan, or pectin. When xyloglucan (0.1%) was added to a cellulose-forming culture of Acetobacter xylinum, cellulose ribbon structure was partially disrupted indicating an association of xyloglucan with cellulose at the time of synthesis. Such a result suggests that the small size of primary wall microfibrils in higher plants may well be due to the binding of xyloglucan to cellulose during synthesis which prevents fasciation of small fibrils into larger bundles. Fluorescent xyloglucan was used to stain pea cell wall ghosts prepared to contain only the native xyloglucan:cellulose network or only cellulose. Ghosts containing only cellulose showed strong fluorescence when prepared before or after elongation; as predicted, the presence of native xyloglucan in the ghosts repressed binding of added fluorescent xyloglucan. Such ghosts, prepared after elongation when the ratio of native xyloglucan:cellulose is substantially reduced, still showed only faint fluorescence, indicating that microfibrils continue to be coated with xyloglucan throughout the growth period. Images Fig. 5 Fig. 6 PMID:16665254

  6. Cellulose biosynthesis and function in bacteria.

    PubMed Central

    Ross, P; Mayer, R; Benziman, M

    1991-01-01

    The current model of cellulose biogenesis in plants, as well as bacteria, holds that the membranous cellulose synthase complex polymerizes glucose moieties from UDP-Glc into beta-1,4-glucan chains which give rise to rigid crystalline fibrils upon extrusion at the outer surface of the cell. The distinct arrangement and degree of association of the polymerizing enzyme units presumably govern extracellular chain assembly in addition to the pattern and width of cellulose fibril deposition. Most evident for Acetobacter xylinum, polymerization and assembly appear to be tightly coupled. To date, only bacteria have been effectively studied at the biochemical and genetic levels. In A. xylinum, the cellulose synthase, composed of at least two structurally similar but functionally distinct subunits, is subject to a multicomponent regulatory system. Regulation is based on the novel nucleotide cyclic diguanylic acid, a positive allosteric effector, and the regulatory enzymes maintaining its intracellular turnover: diguanylate cyclase and Ca2(+)-sensitive bis-(3',5')-cyclic diguanylic acid (c-di-GMP) phosphodiesterase. Four genes have been isolated from A. xylinum which constitute the operon for cellulose synthesis. The second gene encodes the catalytic subunit of cellulose synthase; the functions of the other three gene products are still unknown. Exclusively an extracellular product, bacterial cellulose appears to fulfill diverse biological roles within the natural habitat, conferring mechanical, chemical, and physiological protection in A. xylinum and Sarcina ventriculi or facilitating cell adhesion during symbiotic or infectious interactions in Rhizobium and Agrobacterium species. A. xylinum is proving to be most amenable for industrial purposes, allowing the unique features of bacterial cellulose to be exploited for novel product applications. Images PMID:2030672

  7. Tissue engineering for periodontal regeneration.

    PubMed

    Kao, Richard T; Conte, Greg; Nishimine, Dee; Dault, Scott

    2005-03-01

    As a result of periodontal regeneration research, a series of clinical techniques have emerged that permit tissue engineering to be performed for more efficient regeneration and repair of periodontal defects and improved implant site development. Historically, periodontal regeneration research has focused on a quest for "magic filler" material. This search has led to the development of techniques utilizing autologous bone and bone marrow, allografts, xenografts, and various man-made bone substitutes. Though these techniques have had limited success, the desire for a more effective regenerative approach has resulted in the development of tissue engineering techniques. Tissue engineering is a relatively new field of reconstructive biology which utilizes mechanical, cellular, or biologic mediators to facilitate reconstruction/regeneration of a particular tissue. In periodontology, the concept of tissue engineering had its beginnings with guided tissue regeneration, a mechanical approach utilizing nonresorbable membranes to obtain regeneration in defects. In dental implantology, guided bone regeneration membranes +/- mechanical support are used for bone augmentation of proposed implant placement sites. With the availability of partially purified protein mixture from developing teeth and growth factors from recombinant technology, a new era of tissue engineering whereby biologic mediators can be used for periodontal regeneration. The advantage of recombinant growth factors is this tissue engineering device is consistent in its regenerative capacity, and variations in regenerative response are due to individual healing response and/or poor surgical techniques. In this article, the authors review how tissue engineering has advanced and discuss its impact on the clinical management of both periodontal and osseous defects in preparation for implant placement. An understanding of these new tissue engineering techniques is essential for comprehending today's ever

  8. Hybrid nanocomposite based on cellulose and tin oxide: growth, structure, tensile and electrical characteristics

    PubMed Central

    Mahadeva, Suresha K; Kim, Jaehwan

    2011-01-01

    A highly flexible nanocomposite was developed by coating a regenerated cellulose film with a thin layer of tin oxide (SnO2) by liquid-phase deposition. Tin oxide was crystallized in solution and formed nanocrystal coatings on regenerated cellulose. The nanocrystalline layers did not exfoliate from cellulose. Transmission electron microscopy and energy dispersive x-ray spectroscopy suggest that SnO2 was not only deposited over the cellulose surface, but also nucleated and grew inside the cellulose film. Current–voltage characteristics of the nanocomposite revealed that its electrical resistivity decreases with deposition time, with the lowest value obtained for 24 h of deposition. The cellulose–SnO2 hybrid nanocomposite can be used for biodegradable and disposable chemical, humidity and biosensors. PMID:27877444

  9. Isolation and recovery of cellulose from waste nylon/cotton blended fabrics by 1-allyl-3-methylimidazolium chloride.

    PubMed

    Lv, Fangbing; Wang, Chaoxia; Zhu, Ping; Zhang, Chuanjie

    2015-06-05

    Development of a simple process for separating cellulose and nylon 6 from their blended fabrics is indispensable for recycling of waste mixed fabrics. An efficient procedure of dissolution of the fabrics in an ionic liquid 1-allyl-3-methylimidazolium chloride ([AMIM]Cl) and subsequent filtration separation has been demonstrated. Effects of treatment temperature, time and waste fabrics ratio on the recovery rates were investigated. SEM images showed that the cotton cellulose dissolved in [AMIM]Cl while the nylon 6 fibers remained. The FTIR spectrum of regenerated cellulose (RC) was similar with that of virgin cotton fibers, which verified that no other chemical reaction occurred besides breakage of hydrogen bonds during the processes of dissolution and separation. TGA curves indicated that the regenerated cellulose possessed a reduced thermal stability and was effectively removed from waste nylon/cotton blended fabrics (WNCFs). WNCFs were sufficiently reclaimed with high recovery rate of both regenerated cellulose films and nylon 6 fibers.

  10. Quantitative determination of cellulose accessibility to cellulase based on adsorption of a nonhydrolytic fusion protein containing CBM and GFP with its applications.

    PubMed

    Hong, Jiong; Ye, Xinhao; Zhang, Y-H Percival

    2007-12-04

    Heterogeneous cellulose accessibility is an important substrate characteristic, but all methods for determining cellulose accessibility to the large-size cellulase molecule have some limitations. Characterization of cellulose accessibility to cellulase (CAC) is vital for better understanding of the enzymatic cellulose hydrolysis mechanism (Zhang and Lynd, Biotechnol. Bioeng. 2004, 88, 797-824; 2006, 94, 888-898). Quantitative determination of cellulose accessibility to cellulase (m2/g of cellulose) was established based on the Langmuir adsorption of the fusion protein containing a cellulose-binding module (CBM) and a green fluorescent protein (GFP). One molecule of the recombinant fusion protein occupied 21.2 cellobiose lattices on the 110 face of bacterial cellulose nanofibers. The CAC values of several cellulosic materials -- regenerated amorphous cellulose (RAC), bacterial microcrystalline cellulose (BMCC), Whatman No. 1 filter paper, fibrous cellulose powder (CF1), and microcrystalline cellulose (Avicel) -- were 41.9, 33.5, 9.76, 4.53, and 2.38 m2/g, respectively. The CAC value of amorphous cellulose made from Avicel was 17.6-fold larger than that of crystalline cellulose - Avicel. Avicel enzymatic hydrolysis proceeded with a transition from substrate excess to substrate limited. The declining hydrolysis rates over conversion are mainly attributed to a combination of substrate consumption and a decrease in substrate reactivity. Declining heterogeneous cellulose reactivity is significantly attributed to a loss of CAC where the easily hydrolyzed cellulose fraction is digested first.

  11. High magnetic field quantum transport in Au nanoparticle-cellulose films.

    PubMed

    Turyanska, L; Makarovsky, O; Patanè, A; Kozlova, N V; Liu, Z; Li, M; Mann, S

    2012-02-03

    We report the magneto-transport properties of cellulose films comprising interconnected networks of gold nanoparticles (Au NPs). Cellulose is a biopolymer that can be made electrically conducting by cellulose regeneration in Au NP dispersions. The mechanism of electronic conduction in the Au-cellulose films changes from variable range hopping to metallic-like conduction with decreasing resistivity. Our experiments in high magnetic fields (up to 45 T) reveal negative magnetoresistance in the highly resistive films. This is attributed to the spin polarization of the Au NPs and the magnetic field induced suppression of electron spin flips during spin-polarized tunneling in the NP network.

  12. Myomaker is essential for muscle regeneration.

    PubMed

    Millay, Douglas P; Sutherland, Lillian B; Bassel-Duby, Rhonda; Olson, Eric N

    2014-08-01

    Regeneration of injured adult skeletal muscle involves fusion of activated satellite cells to form new myofibers. Myomaker is a muscle-specific membrane protein required for fusion of embryonic myoblasts, but its potential involvement in adult muscle regeneration has not been explored. We show that myogenic basic helix-loop-helix (bHLH) transcription factors induce myomaker expression in satellite cells during acute and chronic muscle regeneration. Moreover, genetic deletion of myomaker in adult satellite cells completely abolishes muscle regeneration, resulting in severe muscle destruction after injury. Myomaker is the only muscle-specific protein known to be absolutely essential for fusion of embryonic and adult myoblasts.

  13. Myomaker is essential for muscle regeneration

    PubMed Central

    Millay, Douglas P.; Sutherland, Lillian B.; Bassel-Duby, Rhonda

    2014-01-01

    Regeneration of injured adult skeletal muscle involves fusion of activated satellite cells to form new myofibers. Myomaker is a muscle-specific membrane protein required for fusion of embryonic myoblasts, but its potential involvement in adult muscle regeneration has not been explored. We show that myogenic basic helix–loop–helix (bHLH) transcription factors induce myomaker expression in satellite cells during acute and chronic muscle regeneration. Moreover, genetic deletion of myomaker in adult satellite cells completely abolishes muscle regeneration, resulting in severe muscle destruction after injury. Myomaker is the only muscle-specific protein known to be absolutely essential for fusion of embryonic and adult myoblasts. PMID:25085416

  14. Cellulose-silica aerogels.

    PubMed

    Demilecamps, Arnaud; Beauger, Christian; Hildenbrand, Claudia; Rigacci, Arnaud; Budtova, Tatiana

    2015-05-20

    Aerogels based on interpenetrated cellulose-silica networks were prepared and characterised. Wet coagulated cellulose was impregnated with silica phase, polyethoxydisiloxane, using two methods: (i) molecular diffusion and (ii) forced flow induced by pressure difference. The latter allowed an enormous decrease in the impregnation times, by almost three orders of magnitude, for a sample with the same geometry. In both cases, nanostructured silica gel was in situ formed inside cellulose matrix. Nitrogen adsorption analysis revealed an almost threefold increase in pores specific surface area, from cellulose aerogel alone to organic-inorganic composite. Morphology, thermal conductivity and mechanical properties under uniaxial compression were investigated. Thermal conductivity of composite aerogels was lower than that of cellulose aerogel due to the formation of superinsulating mesoporous silica inside cellulose pores. Furthermore, composite aerogels were stiffer than each of reference aerogels.

  15. A comparative evaluation of the effectiveness of guided tissue regeneration by using a collagen membrane with or without decalcified freeze-dried bone allograft in the treatment of infrabony defects: A clinical and radiographic study

    PubMed Central

    Kher, Vishal Kiran; Bhongade, Manohar L.; Shori, Tony D.; Kolte, Abhay P.; Dharamthok, Swarup B.; Shrirao, Tushar S.

    2013-01-01

    Background: The present, randomized, controlled clinical and radiographic study was undertaken to compare the effectiveness of guided tissue regeneration (GTR) by using a collagen membrane barrier with or without decalcified freeze-dried bone allograft (DFDBA) in the treatment of periodontal infrabony defects characterized by unfavorable architecture. Materials and Methods: Sixteen systemically healthy patients with 20 periodontal infrabony defects were selected for the study. Each patient had at least ≥ 5 mm clinical probing pocket depth (PPD) at the selected site and depth of intrabony component ≥ 3 mm as assessed by clinical and radiographic measurements. Baseline measurements included plaque index, papillary bleeding index, PPD, gingival recession, clinical attachment level and radiographic defect depth (DD). At the time of surgery, the defects were randomly assigned to either the test group (collagen membrane plus DFDBA) or the control group (collagen membrane only). Results: At the 6-month examination, PPPD reduction was significantly greater in the GTR + DFDBA group (4.06 ± 0.38 mm) compared with the GTR group (3.2 ± 0.74 mm). The mean gains of clinical attachment were 3.54 ± 0.36 mm in the test group and 2.50 ± 0.74 mm in the control group. Radiographic DD reduction was similarly greater in the GTR + DFDBA group (2.40 ± 0.51 mm) compared with the GTR group (1.60 ± 0.51 mm). Conclusions: The results of the present study indicate that the use of a GTR membrane with bone graft has significantly improved all clinical parameters tested as compared with the use of bioresorbable membrane alone in the treatment of infrabony defects characterized by unfavorable architecture. PMID:24174729

  16. CMC-modified cellulose biointerface for antibody conjugation.

    PubMed

    Orelma, Hannes; Teerinen, Tuija; Johansson, Leena-Sisko; Holappa, Susanna; Laine, Janne

    2012-04-09

    In this Article, we present a new strategy for preparing an antihemoglobin biointerface on cellulose. The preparation method is based on functionalization of the cellulose surface by the irreversible adsorption of CMC, followed by covalent linking of antibodies to CMC. This would provide the means for affordable and stable cellulose-based biointerfaces for immunoassays. The preparation and characterization of the biointerface were studied on Langmuir-Schaefer cellulose model surfaces in real time using the quartz crystal microbalance with dissipation and surface plasmon resonance techniques. The stable attachment of antihemoglobin to adsorbed CMC was achieved, and a linear calibration of hemoglobin was obtained. CMC modification was also observed to prevent nonspecific protein adsorption. The antihemoglobin-CMC surface regenerated well, enabling repeated immunodetection cycles of hemoglobin on the same surface.

  17. Functionalization of cellulose acetate fibers with engineered cutinases.

    PubMed

    Matamá, Teresa; Araújo, Rita; Gübitz, Georg M; Casal, Margarida; Cavaco-Paulo, Artur

    2010-01-01

    In the present work, we describe for the first time the specific role of cutinase on surface modification of cellulose acetate fibers. Cutinase exhibits acetyl esterase activity on diacetate and triacetate of 0.010 U and 0.007 U, respectively. An increase on the hydroxyl groups at the fiber surface of 25% for diacetate and 317% for triacetate, after a 24 h treatment, is estimated by an indirect assay. Aiming at further improvement of cutinase affinity toward cellulose acetate, chimeric cutinases are genetically engineered by fusing the 3'-end coding sequence with a bacterial or a fungal carbohydrate-binding module and varying the linker DNA sequence. A comparative analysis of these genetic constructions is presented showing that, the superficial regeneration of cellulose hydrophilicity and reactivity on highly substituted cellulose acetates is achieved by chimeric cutinases.

  18. Evaluating Models of Cellulose Degradation by Fibrobacter succinogenes S85.

    PubMed

    Burnet, Meagan C; Dohnalkova, Alice C; Neumann, Anthony P; Lipton, Mary S; Smith, Richard D; Suen, Garret; Callister, Stephen J

    2015-01-01

    Fibrobacter succinogenes S85 is an anaerobic non-cellulosome utilizing cellulolytic bacterium originally isolated from the cow rumen microbial community. Efforts to elucidate its cellulolytic machinery have resulted in the proposal of numerous models which involve cell-surface attachment via a combination of cellulose-binding fibro-slime proteins and pili, the production of cellulolytic vesicles, and the entry of cellulose fibers into the periplasmic space. Here, we used a combination of RNA-sequencing, proteomics, and transmission electron microscopy (TEM) to further clarify the cellulolytic mechanism of F. succinogenes. Our RNA-sequence analysis shows that genes encoding type II and III secretion systems, fibro-slime proteins, and pili are differentially expressed on cellulose, relative to glucose. A subcellular fractionation of cells grown on cellulose revealed that carbohydrate active enzymes associated with cellulose deconstruction and fibro-slime proteins were greater in the extracellular medium, as compared to the periplasm and outer membrane fractions. TEMs of samples harvested at mid-exponential and stationary phases of growth on cellulose and glucose showed the presence of grooves in the cellulose between the bacterial cells and substrate, suggesting enzymes work extracellularly for cellulose degradation. Membrane vesicles were only observed in stationary phase cultures grown on cellulose. These results provide evidence that F. succinogenes attaches to cellulose fibers using fibro-slime and pili, produces cellulases, such as endoglucanases, that are secreted extracellularly using type II and III secretion systems, and degrades the cellulose into cellodextrins that are then imported back into the periplasm for further digestion by β-glucanases and other cellulases.

  19. Evaluating models of cellulose degradation by Fibrobacter succinogenes S85

    DOE PAGES

    Burnet, Meagan C.; Dohnalkova, Alice C.; Neumann, Anthony P.; ...

    2015-12-02

    Fibrobacter succinogenes S85 is an anaerobic non-cellulosome utilizing cellulolytic bacterium originally isolated from the cow rumen microbial community. Efforts to elucidate its cellulolytic machinery have resulted in the proposal of numerous models which involve a combination of cell-surface attachment via a combination of cellulose-binding fibro-slime proteins and pili, the production of cellulolytic vesicles, and the entry of cellulose fibers into the periplasmic space. Here, we used a combination of RNA-sequencing, proteomics, and transmission electron microscopy (TEM) to further elucidate the cellulolytic mechanism of F. succinogenes. Our RNA-sequence analysis shows that genes encoding Type II and III secretion systems, fibro-slime proteins,more » and pili are differentially expressed on cellulose, relative to glucose. A subcellular fractionation of cells grown on cellulose revealed that carbohydrate active enzymes associated with cellulose deconstruction and fibro-slime proteins were greater in the extracellular media, as compared to the periplasm and outer membrane fractions. TEMs of samples harvested at mid-exponential and stationary phases of growth on cellulose and glucose showed the presence of grooves in the cellulose between the bacterial cells and substrate, suggesting enzymes work extracellularly for cellulose degradation. Membrane vesicles were only observed in stationary phase cultures grown on cellulose. Furthermore, these results provide evidence that F. succinogenes attaches to cellulose fibers using fibro-slime and pili, produces cellulases, such as endoglucanases, that are secreted extracellularly using type II and III secretion systems, and degrades the cellulose into cellodextrins that are then imported back into the periplasm for further digestion by β-glucanases and other cellulases.« less

  20. Evaluating Models of Cellulose Degradation by Fibrobacter succinogenes S85

    PubMed Central

    Burnet, Meagan C.; Dohnalkova, Alice C.; Neumann, Anthony P.; Lipton, Mary S.; Smith, Richard D.; Suen, Garret; Callister, Stephen J.

    2015-01-01

    Fibrobacter succinogenes S85 is an anaerobic non-cellulosome utilizing cellulolytic bacterium originally isolated from the cow rumen microbial community. Efforts to elucidate its cellulolytic machinery have resulted in the proposal of numerous models which involve cell-surface attachment via a combination of cellulose-binding fibro-slime proteins and pili, the production of cellulolytic vesicles, and the entry of cellulose fibers into the periplasmic space. Here, we used a combination of RNA-sequencing, proteomics, and transmission electron microscopy (TEM) to further clarify the cellulolytic mechanism of F. succinogenes. Our RNA-sequence analysis shows that genes encoding type II and III secretion systems, fibro-slime proteins, and pili are differentially expressed on cellulose, relative to glucose. A subcellular fractionation of cells grown on cellulose revealed that carbohydrate active enzymes associated with cellulose deconstruction and fibro-slime proteins were greater in the extracellular medium, as compared to the periplasm and outer membrane fractions. TEMs of samples harvested at mid-exponential and stationary phases of growth on cellulose and glucose showed the presence of grooves in the cellulose between the bacterial cells and substrate, suggesting enzymes work extracellularly for cellulose degradation. Membrane vesicles were only observed in stationary phase cultures grown on cellulose. These results provide evidence that F. succinogenes attaches to cellulose fibers using fibro-slime and pili, produces cellulases, such as endoglucanases, that are secreted extracellularly using type II and III secretion systems, and degrades the cellulose into cellodextrins that are then imported back into the periplasm for further digestion by β-glucanases and other cellulases. PMID:26629814