Increase in NOx emissions from Indian thermal power plants during 1996-2010: unit-based inventories and multisatellite observations.

PubMed

Lu, Zifeng; Streets, David G

2012-07-17

Driven by rapid economic development and growing electricity demand, NO(x) emissions (E) from the power sector in India have increased dramatically since the mid-1990s. In this study, we present the NO(x) emissions from Indian public thermal power plants for the period 1996-2010 using a unit-based methodology and compare the emission estimates with the satellite observations of NO(2) tropospheric vertical column densities (TVCDs) from four spaceborne instruments: GOME, SCIAMACHY, OMI, and GOME-2. Results show that NO(x) emissions from Indian power plants increased by at least 70% during 1996-2010. Coal-fired power plants, NO(x) emissions from which are not regulated in India, contribute ∼96% to the total power sector emissions, followed by gas-fired (∼4%) and oil-fired (<1%) ones. A number of isolated NO(2) hot spots are observed over the power plant areas, and good agreement between NO(2) TVCDs and NO(x) emissions is found for areas dominated by power plant emissions. Average NO(2) TVCDs over power plant areas were continuously increasing during the study period. We find that the ratio of ΔE/E to ΔTVCD/TVCD changed from greater than one to less than one around 2005-2008, implying that a transition of the overall NO(x) chemistry occurred over the power plant areas, which may cause significant impact on the atmospheric environment.

Wildfire and soil emissions of NOx and their consequences for ozone observed at a remote mountaintop site in Central California

NASA Astrophysics Data System (ADS)

Asher, E. C. C.; Caputi, D.; Conley, S. A.; Faloona, I. C.

2016-12-01

Nitric oxide (NOx) emissions contribute to the production of tropospheric ozone and the nutrient supply fueling primary production. Current global estimates indicate that biomass burning, including wildfires, and soil emissions represent 15 - 25 % of the total emissions. Yet estimates suggest that in North America during the summer, natural sources, including biomass burning, soil emissions and lightning, are responsible for nearly half of total emissions. Thus, as domestic air quality standards grow stricter and anthropogenic sources more regulated, constraining natural sources of NOx becomes critical. NOx concentrations in wildfire smoke differ based on the age of the plume, fire intensity and vegetation type. NOx soil emissions depend on soil moisture, soil temperature, soil porosity, and nitrogen storage. We present two years of NOx and ozone (O3) measurements from a remote mountaintop monitoring site located on Chews Ridge in the coastal mountains of Central California, airborne observations, and remotely sensed NO2 tropospheric columns retrieved using the Ozone Monitoring Instrument (OMI). We explore controls on NOx concentrations at Chews Ridge, in Monterey County, such as the age of wildfire smoke plumes and wildfire intensity (i.e. burning vs. smoldering), as well as soil moisture and precipitation, which can lead to pulsed NOx fluxes. Most recently our in situ observations fortuitously captured differing amounts of the active plume of the Soberanes wildfire, which to date has burned >45,000 acres and is expected to continue partially contained through August 2016. Implications of these episodic sources of NOx on the regional ozone budget will be discussed.

POLICY AND SCIENCE: ASSESSING THE IMPACT OF REGULATIONS ON AIR QUALITY AND HUMAN HEALTH

EPA Science Inventory

This presentation will discuss the NOx SIP call and the results of several studies investigating the impact of the regulation on NOx emissions and ozone levels across the northeastern United States. Current research plans to investigate linkages with human health will also be di...

Lagrangian Hotspots of In-Use NOX Emissions from Transit Buses.

PubMed

Kotz, Andrew J; Kittelson, David B; Northrop, William F

2016-06-07

In-use, spatiotemporal NOX emissions were measured from a conventional powertrain transit bus and a series electric hybrid bus over gradients of route kinetic intensity and ambient temperature. This paper introduces a new method for identifying NOX emissions hotspots along a bus route using high fidelity Lagrangian vehicle data to explore spatial interactions that may influence emissions production. Our study shows that the studied transit buses emit higher than regulated emissions because on-route operation does not accurately represent the range of engine operation tested according to regulatory standards. Using the Lagrangian hotspot detection, we demonstrate that NOX hotspots occurred at bus stops, during cold starts, on inclines, and for accelerations. On the selected routes, bus stops resulted in 3.3 times the route averaged emissions factor in grams/km without significant dependence on bus type or climate. The buses also emitted 2.3 times the route averaged NOX emissions factor at the beginning of each route due to cold selective catalytic reduction aftertreatment temperature. The Lagrangian hotspot detection technique demonstrated here could be employed in future connected vehicles empowered by advances in computational power, data storage capability, and improved sensor technology to optimize emissions as a function of spatial location.

Eddy Covariance Measurements Assessing NOx Emission in London, UK

NASA Astrophysics Data System (ADS)

Drysdale, W. S.; Lee, J. D.; Purvis, R.; Squires, F. A.; Vaughan, A. R.; Metzger, S.

2017-12-01

NOx (the sum of NO + NO2) is emitted during most combustion processes. NO2is a well known air pollutant detrimental to human health, and is regulated in many cities. London often finds itself in breach of these emission regulations. Emission inventories are used in air quality forecast models to predict current and future air pollution levels and to guide abatement strategy. It is therefore crucial that inventories accurately predict emissions; validation can be carried out using direct measurements. Measurements of NO and NO2 at 5 Hz have been made at the BT Tower, 190 m above street level in central London. Eddy covariance calculations have been performed using both classical and "continuous wavelet transformation" method, producing half hour and 1 minute resolved NOx fluxes respectively. We present a first look at these flux data measured in early 2017. A strong diurnal profile for NOx flux is observed, with an increase from 5am to 7am, and remaining constant around 1400 ng m2 m-1 throughout the day, before decreasing to background levels towards midnight. Data is also compared to previous NOx flux measurements over two periods, June-July 2012 and March-April 2013 to examine how emissions have changed over this period. A significant decrease in NOx emissions ( 64%, a mean flux of 2400 ng m2 s-1 in 2012 to a mean 870 ng m2 s-1 in 2017) is observed. When the fluxes are separated by wind flow from the east and west, there is negligible difference in 2017, where 2012 saw lower fluxes from the east, especially in the afternoon. By coupling the measurements with a footprint model we compare the data to emission estimates from the UK's National Atmospheric Emission Inventory (NAEI). In 2012-13 emissions were measured to be twice as high than the NAEI predicted and the latest data shows a much better agreement.

Characterizing emission rates of regulated pollutants from model year 2012+ heavy-duty diesel vehicles equipped with DPF and SCR systems.

PubMed

Jiang, Yu; Yang, Jiacheng; Cocker, David; Karavalakis, Georgios; Johnson, Kent C; Durbin, Thomas D

2018-04-01

The regulated emissions of five 2012 and newer, low-mileage, heavy-duty Class 8 diesel trucks equipped with diesel particulate filters (DPFs) and selective catalytic reduction (SCR) systems were evaluated over test cycles representing urban, highway, and stop-and-go driving on a chassis dynamometer. NOx emissions over the Urban Dynamometer Driving Schedule (UDDS) ranged from 0.495 to 1.363g/mi (0.136 to 0.387g/bhp-hr) for four of the normal emitting trucks. For those trucks, NOx emissions were lowest over the cruise (0.068 to 0.471g/mi) and high-speed cruise (0.067 to 0.249g/mi) cycles, and highest for the creep cycle (2.131 to 9.468g/mi). A fifth truck showed an anomaly in that it had never regenerated throughout its relatively short operating lifetime due to its unusual, unladed service history. This truck exhibited NOx emissions of 3.519g/mi initially over the UDDS, with UDDS NOx emissions decreasing to 0.39g/mi after a series of parked regenerations. PM, THC, and CO emissions were found to be very low for most of the testing conditions, due to the presence of the DPF/SCR aftertreatment system, and were comparable to background levels in some cases. Copyright © 2017 Elsevier B.V. All rights reserved.

Emission reduction potential of using gas-to-liquid and dimethyl ether fuels on a turbocharged diesel engine.

PubMed

Xinling, Li; Zhen, Huang

2009-03-15

A study of engine performance characteristics and both of regulated (CO, HC, NO(x), and smoke) and unregulated (ultrafine particle number, mass concentrations and size distribution) emissions for a turbocharged diesel engine fueled with conventional diesel, gas-to-liquid (GTL) and dimethyl ether (DME) fuels respectively at different engine loads and speeds have been carried out. The results indicated that fuel components significantly affected the engine performance and regulated/unregulated emissions. GTL exhibited almost the same power and torque output as diesel, while improved fuel economy. GTL significantly reduced regulated emissions with average reductions of 21.2% in CO, 15.7% in HC, 15.6% in NO(x) and 22.1% in smoke in comparison to diesel, as well as average reductions in unregulated emissions of total ultrafine particle number (N(tot)) and mass (M(tot)) emissions by 85.3% and 43.9%. DME can significantly increase torque and power, compared with the original diesel engine, as well as significantly reduced regulated emissions of 40.1% in HC, 48.2% in NO(x) and smoke free throughout all the engine conditions. However, N(tot) for DME is close to that for diesel. The reason is that the accumulation mode particle number emissions for DME are very low due to the characteristics of oxygen content and no C-C bond, which promotes the processes of nucleation and condensation of the semi-volatile compounds in the exhaust gas, as a result, a lot of nucleation mode particles produce.

Exhaust particle and NOx emission performance of an SCR heavy duty truck operating in real-world conditions

NASA Astrophysics Data System (ADS)

Saari, Sampo; Karjalainen, Panu; Ntziachristos, Leonidas; Pirjola, Liisa; Matilainen, Pekka; Keskinen, Jorma; Rönkkö, Topi

2016-02-01

Particle and NOx emissions of an SCR equipped HDD truck were studied in real-world driving conditions using the "Sniffer" mobile laboratory. Real-time CO2 measurement enables emission factor calculation for NOx and particles. In this study, we compared three different emission factor calculation methods and characterised their suitability for real-world chasing experiments. The particle number emission was bimodal and dominated by the nucleation mode particles (diameter below 23 nm) having emission factor up to 1 × 1015 #/kgfuel whereas emission factor for soot (diameter above 23 nm that is consistent with the PMP standard) was typically 1 × 1014 #/kgfuel. The effect of thermodenuder on the exhaust particles indicated that the nucleation particles consisted mainly of volatile compounds, but sometimes there also existed a non-volatile core. The nucleation mode particles are not controlled by current regulations in Europe. However, these particles consistently form under atmospheric dilution in the plume of the truck and constitute a health risk for the human population that is exposed to those. Average NOx emission was 3.55 g/kWh during the test, whereas the Euro IV emission limit over transient testing is 3.5 g NOx/kWh. The on-road emission performance of the vehicle was very close to the expected levels, confirming the successful operation of the SCR system of the tested vehicle. Heavy driving conditions such as uphill driving increased both the NOx and particle number emission factors whereas the emission factor for soot particle number remains rather constant.

Impacts and mitigation of excess diesel-related NOx emissions in 11 major vehicle markets

NASA Astrophysics Data System (ADS)

Anenberg, Susan C.; Miller, Joshua; Minjares, Ray; Du, Li; Henze, Daven K.; Lacey, Forrest; Malley, Christopher S.; Emberson, Lisa; Franco, Vicente; Klimont, Zbigniew; Heyes, Chris

2017-05-01

Vehicle emissions contribute to fine particulate matter (PM2.5) and tropospheric ozone air pollution, affecting human health, crop yields and climate worldwide. On-road diesel vehicles produce approximately 20 per cent of global anthropogenic emissions of nitrogen oxides (NOx), which are key PM2.5 and ozone precursors. Regulated NOx emission limits in leading markets have been progressively tightened, but current diesel vehicles emit far more NOx under real-world operating conditions than during laboratory certification testing. Here we show that across 11 markets, representing approximately 80 per cent of global diesel vehicle sales, nearly one-third of on-road heavy-duty diesel vehicle emissions and over half of on-road light-duty diesel vehicle emissions are in excess of certification limits. These excess emissions (totalling 4.6 million tons) are associated with about 38,000 PM2.5- and ozone-related premature deaths globally in 2015, including about 10 per cent of all ozone-related premature deaths in the 28 European Union member states. Heavy-duty vehicles are the dominant contributor to excess diesel NOx emissions and associated health impacts in almost all regions. Adopting and enforcing next-generation standards (more stringent than Euro 6/VI) could nearly eliminate real-world diesel-related NOx emissions in these markets, avoiding approximately 174,000 global PM2.5- and ozone-related premature deaths in 2040. Most of these benefits can be achieved by implementing Euro VI standards where they have not yet been adopted for heavy-duty vehicles.

Measurement of NOx fluxes from a tall tower in Beijing

NASA Astrophysics Data System (ADS)

Squires, Freya; Dunmore, Rachel; Lewis, Alastair; Vaughan, Adam; Mullinger, Neil; Nemitz, Eiko; Wild, Oliver; Zhang, Qiang; Hamilton, Jacqueline; Lee, James; Fu, Pingqing

2017-04-01

Nitrogen Oxides (NOx, the sum of nitrogen monoxide (NO) and nitrogen dioxide (NO2)) are significant anthropogenic pollutants emitted from most combustion processes. NOx is a precursor species to the formation of O3 and secondary aerosols and, in high concentrations, NO2 can have adverse effects on human health through action as a respiratory irritant. For these reasons, there has been increased focus on improving NOx emissions inventories, typically developed using 'bottom-up' estimates of emissions from their sources, which are used to predict current and future air quality and to guide abatement strategy. Recent studies have shown a discrepancy between NOx inventories and measured NOx emissions for UK cities, highlighting the limitations of bottom-up emissions inventories and the importance of accurate measurement data to improve the estimates. Similarly, inventories in China are associated with large uncertainties and are rapidly changing with time in response to economic development and new environmental regulation. Here, we present data collected as part of the Air Pollutants in Beijing (AIRPOLL-Beijing) campaign from an urban site located at the Institute of Atmospheric Physics, Chinese Academy of Sciences (IAP, CAS) (39˚ 58'28"N, 116˚ 22'16"E) in central Beijing. NOx concentrations were measured using a state-of-the-art chemiluminescence instrument, sampling from an inlet at 100 metres on a meteorological tower. Measurements at 5 Hz coupled with wind vector data measured by a sonic anemometer located at the same height as the inlet allowed NOx emission fluxes to be calculated using the eddy covariance method. Measurements were made during the period 11/11/2016 - 10/12/2016 and compared to existing emission estimates from The Multi-resolution Emission Inventory for China (MEIC) inventory. It is anticipated that this work will be used to evaluate the accuracy of emissions inventories for Beijing, to develop improved emissions estimates and thus provide greater information about the sources of NOx in the city.

Air quality benefits of universal particle filter and NOx controls on diesel trucks

NASA Astrophysics Data System (ADS)

Tao, L.; Mcdonald, B. C.; Harley, R.

2015-12-01

Heavy-duty diesel trucks are a major source of black carbon/particulate matter and nitrogen oxide emissions on urban and regional scales. These emissions are relevant to both air quality and climate change. Since 2010 in the US, new engines are required to be equipped with emission control systems that greatly reduce both PM and NOx emissions, by ~98% relative to 1988 levels. To reduce emissions from the legacy fleet of older trucks that still remain on the road, regulations have been adopted in Califonia to accelerate the replacement of older trucks and thereby reduce associated emissions of PM and NOx. Use of diesel particle filters will be widespread by 2016, and universal use of catalytic converters for NOx control is required by 2023. We assess the air quality consequences of this clean-up effort in Southern California, using the Community Multiscale Air Quality model (CMAQ), and comparing three scenarios: historical (2005), present day (2016), and future year (2023). Emissions from the motor vehicle sector are mapped at high spatial resolution based on traffic count and fuel sales data. NOx emissions from diesel engines in 2023 are expected to decrease by ~80% compared to 2005, while the fraction of NOx emitted as NO2 is expected to increase from 5 to 18%. Air quality model simulations will be analyzed to quantify changes in NO2, black carbon, particulate matter, and ozone, both basin-wide and near hot spots such as ports and major highways.

Implications of near-term coal power plant retirement for SO2 and NOX and life cycle GHG emissions.

PubMed

Venkatesh, Aranya; Jaramillo, Paulina; Griffin, W Michael; Matthews, H Scott

2012-09-18

Regulations monitoring SO(2), NO(X), mercury, and other metal emissions in the U.S. will likely result in coal plant retirement in the near-term. Life cycle assessment studies have previously estimated the environmental benefits of displacing coal with natural gas for electricity generation, by comparing systems that consist of individual natural gas and coal power plants. However, such system comparisons may not be appropriate to analyze impacts of coal plant retirement in existing power fleets. To meet this limitation, simplified economic dispatch models for PJM, MISO, and ERCOT regions are developed in this study to examine changes in regional power plant dispatch that occur when coal power plants are retired. These models estimate the order in which existing power plants are dispatched to meet electricity demand based on short-run marginal costs, with cheaper plants being dispatched first. Five scenarios of coal plant retirement are considered: retiring top CO(2) emitters, top NO(X) emitters, top SO(2) emitters, small and inefficient plants, and old and inefficient plants. Changes in fuel use, life cycle greenhouse gas emissions (including uncertainty), and SO(2) and NO(X) emissions are estimated. Life cycle GHG emissions were found to decrease by less than 4% in almost all scenarios modeled. In addition, changes in marginal damage costs due to SO(2), and NO(X) emissions are estimated using the county level marginal damage costs reported in the Air Pollution Emissions Experiments and Policy (APEEP) model, which are a proxy for measuring regional impacts of SO(2) and NO(X) emissions. Results suggest that location specific parameters should be considered within environmental policy frameworks targeting coal plant retirement, to account for regional variability in the benefits of reducing the impact of SO(2) and NO(X) emissions.

Top-down estimates of methane and nitrogen oxide emissions from shale gas production regions using aircraft measurements and a mesoscale Bayesian inversion system together with a flux ratio inversion technique

NASA Astrophysics Data System (ADS)

Cui, Y.; Brioude, J. F.; Angevine, W. M.; McKeen, S. A.; Henze, D. K.; Bousserez, N.; Liu, Z.; McDonald, B.; Peischl, J.; Ryerson, T. B.; Frost, G. J.; Trainer, M.

2016-12-01

Production of unconventional natural gas grew rapidly during the past ten years in the US which led to an increase in emissions of methane (CH4) and, depending on the shale region, nitrogen oxides (NOx). In terms of radiative forcing, CH4 is the second most important greenhouse gas after CO2. NOx is a precursor of ozone (O3) in the troposphere and nitrate particles, both of which are regulated by the US Clean Air Act. Emission estimates of CH4 and NOx from the shale regions are still highly uncertain. We present top-down estimates of CH4 and NOx surface fluxes from the Haynesville and Fayetteville shale production regions using aircraft data collected during the Southeast Nexus of Climate Change and Air Quality (SENEX) field campaign (June-July, 2013) and the Shale Oil and Natural Gas Nexus (SONGNEX) field campaign (March-May, 2015) within a mesoscale inversion framework. The inversion method is based on a mesoscale Bayesian inversion system using multiple transport models. EPA's 2011 National CH4 and NOx Emission Inventories are used as prior information to optimize CH4 and NOx emissions. Furthermore, the posterior CH4 emission estimates are used to constrain NOx emission estimates using a flux ratio inversion technique. Sensitivity of the posterior estimates to the use of off-diagonal terms in the error covariance matrices, the transport models, and prior estimates is discussed. Compared to the ground-based in-situ observations, the optimized CH4 and NOx inventories improve ground level CH4 and O3 concentrations calculated by the Weather Research and Forecasting mesoscale model coupled with chemistry (WRF-Chem).

NOx Emissions from Large Point Sources: Variability in Ozone Production, Resulting Health Damages and Economic Costs

NASA Astrophysics Data System (ADS)

Mauzerall, D. L.; Sultan, B.; Kim, N.; Bradford, D.

2004-12-01

We present a proof-of-concept analysis of the measurement of the health damage of ozone (O3) produced from nitrogen oxides (NOx = NO + NO2) emitted by individual large point sources in the eastern United States. We use a regional atmospheric model of the eastern United States, the Comprehensive Air Quality Model with Extensions (CAMx), to quantify the variable impact that a fixed quantity of NOx emitted from individual sources can have on the downwind concentration of surface O3, depending on temperature and local biogenic hydrocarbon emissions. We also examine the dependence of resulting ozone-related health damages on the size of the exposed population. The investigation is relevant to the increasingly widely used "cap and trade" approach to NOx regulation, which presumes that shifts of emissions over time and space, holding the total fixed over the course of the summer O3 season, will have minimal effect on the environmental outcome. By contrast, we show that a shift of a unit of NOx emissions from one place or time to another could result in large changes in the health effects due to ozone formation and exposure. We indicate how the type of modeling carried out here might be used to attach externality-correcting prices to emissions. Charging emitters fees that are commensurate with the damage caused by their NOx emissions would create an incentive for emitters to reduce emissions at times and in locations where they cause the largest damage.

Measuring in-use ship emissions with international and U.S. federal methods.

PubMed

Khan, M Yusuf; Ranganathan, Sindhuja; Agrawal, Harshit; Welch, William A; Laroo, Christopher; Miller, J Wayne; Cocker, David R

2013-03-01

Regulatory agencies have shifted their emphasis from measuring emissions during certification cycles to measuring emissions during actual use. Emission measurements in this research were made from two different large ships at sea to compare the Simplified Measurement Method (SMM) compliant with the International Maritime Organization (IMO) NOx Technical Code to the Portable Emission Measurement Systems (PEMS) compliant with the US. Environmental Protection Agency (EPA) 40 Code of Federal Regulations (CFR) Part 1065 for on-road emission testing. Emissions of nitrogen oxides (NOx), carbon dioxide (CO2), and carbon monoxide (CO) were measured at load points specified by the International Organization for Standardization (ISO) to compare the two measurement methods. The average percentage errors calculated for PEMS measurements were 6.5%, 0.6%, and 357% for NOx, CO2, and CO, respectively. The NOx percentage error of 6.5% corresponds to a 0.22 to 1.11 g/kW-hr error in moving from Tier III (3.4 g/kW-hr) to Tier I (17.0 g/kW-hr) emission limits. Emission factors (EFs) of NOx and CO2 measured via SMM were comparable to other studies and regulatory agencies estimates. However EF(PM2.5) for this study was up to 26% higher than that currently used by regulatory agencies. The PM2.5 was comprised predominantly of hydrated sulfate (70-95%), followed by organic carbon (11-14%), ash (6-11%), and elemental carbon (0.4-0.8%). This research provides direct comparison between the International Maritime Organization and U.S. Environmental Protection Agency reference methods for quantifying in-use emissions from ships. This research provides correlations for NOx, CO2, and CO measured by a PEMS unit (certified by U.S. EPA for on-road testing) against IMO's Simplified Measurement Method for on-board certification. It substantiates the measurements of NOx by PEMS and quantifies measurement error. This study also provides in-use modal and overall weighted emission factors of gaseous (NOx, CO, CO2, total hydrocarbons [THC], and SO2) and particulate pollutants from the main engine of a container ship, which are helpful in the development of emission inventory.

Using stable isotopes of reactive N in dry and wet deposition to investigate the source, transport, and fate of NOx and NH3

NASA Astrophysics Data System (ADS)

Felix, J.; Elliott, E. M.

2011-12-01

Reactive N emissions (NH3 and NOx) can reach the land surfaces via both wet (NH4+, NO3) and dry (NOx, HNO3, NH3, NH4+) depositional processes. Together, these reactive N compounds are important global contributors to air and water quality degradation. Although nitrate concentrations in wet deposition have decreased in the U.S. during the last two decades due to NOx emission regulations set forth by the Clean Air Act, ammonium concentrations in wet deposition have recently increased. In order to further decrease NOx emissions and decrease NH3 emissions, additional tools for reactive N source apportionment are essential. The stable isotopic composition of reactive N may be one such tool for characterizing source, transport, and fate of reactive N emissions. Here, we present results from a comprehensive inventory of the isotopic composition of reactive N emission sources, focusing mainly on agricultural and fossil fuel sources. We build on these inventory results by tracing reactive N emissions across multiple landscapes including: a dairy operation, a conventionally managed cornfield, a tallgrass prairie, and a concentrated animal feeding operation. We then use two examples to illustrate how reactive N isotopes can be used in a regional context. First, we illustrate how passive NH3 samplers deployed at nine U.S. monitoring sites reflect spatial variations in predominant NH3 sources. Secondly, we reconstruct the regional influence of agricultural NOx emissions to nitrate deposition recorded in an ice core from Summit, Greenland. These results reveal significant evidence that the trend in the N isotopic composition of 20th century nitrate deposition in Greenland was driven by increasing biogenic soil NOx emissions induced by fertilizer application in the US over the last century. Together, these studies demonstrate the isotopic composition of reactive N emissions can be an additional tool for investigators to source and trace reactive N emissions in both historical and modern contexts and across spatial scales.

Measurement of NOx and CO Fluxes from a Tall Tower in Beijing.

NASA Astrophysics Data System (ADS)

Squires, F. A.; Drysdale, W. S.; Hamilton, J.; Lee, J. D.; Vaughan, A. R.; Wild, O.; Mullinger, N.; Nemitz, E.; Metzger, S.; Zhang, Q.

2017-12-01

China's air quality problems are well publicised; in 2010, 1.2 million premature deaths were attributed to outdoor air pollution in China. One of the major air quality issues is high concentrations of nitrogen oxides (NOx). China is the largest NOx emitter, contributing an estimated 18 % to global NOx emissions. Beijing itself is reported to have NO2 concentrations 42 % higher than the annual national standard. Given the high levels of pollution, increased focus has been placed on improving emissions estimates which are typically developed using a `bottom-up' approach where emissions are predicted from their sources. Emission inventories in China have large uncertainties and are rapidly changing with time in response to economic development, environmental regulation and new technologies. In fact, China is the largest contributor to the uncertainty in the source and the magnitude of air pollutants in air quality models. Recent studies have shown a discrepancy between NOx inventories and measured NOx emissions for UK cities, highlighting the limitations of bottom-up emissions inventories and the importance of accurate measurement data to improve the estimates. 5 Hz measurements of NOx and CO concentration were made as part of the Air Pollutants in Beijing (AIRPOLL-Beijing) project during two field campaigns in Nov-Dec 2016 and May-June 2017. Sampling took place from an inlet co-located with a sonic anemometer at 102 m on a meteorological tower in central Beijing. Analysis of the covariance between vertical wind speed and concentration enabled the calculation of emission flux, with an estimated footprint of between 2 - 5 km from the tower (which typically included some major ring roads and expressways). Fluxes were quantified using the continuous wavelet transformation (CWT) method, which enabled one minute resolved fluxes to be calculated. These data were compared to existing emissions estimates from the Multi-resolution Emission Inventory for China (MEIC). It is anticipated that this work will be used to evaluate the accuracy of emissions inventories for Beijing and to develop improved emissions estimates.

Performance of a peroxide-based cetane improvement additive in different diesel fuels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nandi, M.K.; Jacobs, D.C.; Liotta, F.J. Jr.

The implementation of stringent diesel engine emissions regulations is growing worldwide. The use of high cetane diesel fuels is a cost-effective option that can be used to reduce engine emissions. A direct comparison of heavy-duty diesel engine emissions for three different low sulfur diesel fuels treated with di-t-butyl peroxide and 2-ethylhexyl nitrate, at the same cetane level, was evaluated. Both the peroxide and the nitrate cetane improvement additive significantly reduced all regulated and unregulated emissions including the oxides of nitrogen (NOx) emission. Di-t-butyl peroxide shows a small advantage over ethylhexyl nitrate in reducing NOx in all the three fuels. Compatibilitymore » of the peroxide and the nitrate additives, when mixed in a fuel blend, has been demonstrated by cetane response and engine emissions for the fuel blend. 13 refs., 2 figs., 9 tabs.« less

On-road measurement of regulated pollutants from diesel and CNG buses with urea selective catalytic reduction systems

NASA Astrophysics Data System (ADS)

Guo, Jiadong; Ge, Yunshan; Hao, Lijun; Tan, Jianwei; Li, Jiaqiang; Feng, Xiangyu

2014-12-01

In this study, emissions from 13 buses operated in Beijing, including two Euro-III diesel buses, four Euro-IV diesel buses, three Euro-V diesel buses and four Euro-V CNG buses, were characterized in real world conditions. All of the buses tested were fitted with selective catalytic reduction (SCR) systems except for the Euro-III diesel buses. A SEMTECH-DS was used for testing the gaseous pollutants, and an electric low pressure impactor (ELPI) was used for measuring of particle numbers and size distributions. A comparison was made based on emission performance of these buses by employing the VSP approach and fuel- based emissions factors. Diesel buses emitted less CO and THC but more NOx and PM pollutants than CNG buses. The NOx reduction efficiencies of the SCR systems for CNG buses were higher because of the high exhaust temperature and high NO2/NOx ratio, whereas the efficiencies for diesel buses were lower. This resulted in extremely low NOx emissions from CNG buses, but the high NO2/NOx ratio needs further study. Failures of urea injection in the SCR systems were detected in this research, which resulted in very high NOx emissions. The CNG buses also emitted smaller numbers of particles and less particle mass with the presence of oxidation catalysts. Diesel buses satisfying the Euro-V standard performed better than Euro-IV and Euro-III diesel buses in terms of emission performance, except for more nuclei mode particles. Most of time, the Euro-IV diesel buses show no advantages in CO and NOx emissions compared with the Euro-III diesel buses.

Real Driving NOx Emissions of European Trucks and Detection of Manipulated Emission Systems

NASA Astrophysics Data System (ADS)

Pöhler, Denis; Adler, Tim; Krufczik, Chsristopher; Horbanski, Martin; Lampel, Johannes; Platt, Ulrich

2017-04-01

Nitrogen dioxide (NO2) is the most problematic pollutant in Europe and many other countries. NO2 has a negative impact for the health and the environment, and in most European cities the currently allowed mean annual limit of 40μg/m3 is exceeded. Vehicles, especially Diesel, are the most relevant source. They emit NOx (NO + NO2), and NO can also be converted to NO2 in the atmosphere. Thus vehicle NOx emissions are regulated in the EU with the EURO Norm Standard (e.g. EURO 6 since 1.1.2013 for trucks with 400mg/kWh). Trucks achieve these low emissions with complex emission after treatment systems. All EURO 6 trucks and almost all EURO 5 trucks use the SCR system consuming AdBlue to reduce the NOx emissions. Since the diesel emission scandal for cars, it is well known that real driving emissions (RDE) can be several times higher that the EURO Norm Standard. The main problem is that RDE are only randomly investigated. Here we present a study of NOx RDE of more than 250 randomly chosen trucks on German highways. The measurements were performed with a newly developed mobile NOx-ICAD + CO2 -instrument applying the plume chasing measurement principle, where the pollutants are investigated in the emission plume and were converted to emission factors to be compared to the EURO standard. For most trucks the brand, the model name, the country of registration and its EURO class could be determined and used in a statistical analysis. The observed NOx emission data show that typical truck RDE are in the range of the expected EURO Norm or slightly higher. However, almost every fourth truck from Eastern Europe show emissions much higher that the EURO Norm. This was not observed for German trucks. As the emissions increase up to a factor of 5 to 10 these view trucks contribute significantly to the air pollution. These high emissions clearly indicate a defect emission treatment system. Most likely it indicates illegal manipulated emissions systems where the AdBlue injection is blocked (AdBlue emulator) to save money. This study shows that our measurement system can effectively investigate these manipulated vehicles. Further results and consequences of NOx RDE from trucks are presented.

Regulated and unregulated emissions from modern 2010 emissions-compliant heavy-duty on-highway diesel engines.

PubMed

Khalek, Imad A; Blanks, Matthew G; Merritt, Patrick M; Zielinska, Barbara

2015-08-01

The U.S. Environmental Protection Agency (EPA) established strict regulations for highway diesel engine exhaust emissions of particulate matter (PM) and nitrogen oxides (NOx) to aid in meeting the National Ambient Air Quality Standards. The emission standards were phased in with stringent standards for 2007 model year (MY) heavy-duty engines (HDEs), and even more stringent NOX standards for 2010 and later model years. The Health Effects Institute, in cooperation with the Coordinating Research Council, funded by government and the private sector, designed and conducted a research program, the Advanced Collaborative Emission Study (ACES), with multiple objectives, including detailed characterization of the emissions from both 2007- and 2010-compliant engines. The results from emission testing of 2007-compliant engines have already been reported in a previous publication. This paper reports the emissions testing results for three heavy-duty 2010-compliant engines intended for on-highway use. These engines were equipped with an exhaust diesel oxidation catalyst (DOC), high-efficiency catalyzed diesel particle filter (DPF), urea-based selective catalytic reduction catalyst (SCR), and ammonia slip catalyst (AMOX), and were fueled with ultra-low-sulfur diesel fuel (~6.5 ppm sulfur). Average regulated and unregulated emissions of more than 780 chemical species were characterized in engine exhaust under transient engine operation using the Federal Test Procedure cycle and a 16-hr duty cycle representing a wide dynamic range of real-world engine operation. The 2010 engines' regulated emissions of PM, NOX, nonmethane hydrocarbons, and carbon monoxide were all well below the EPA 2010 emission standards. Moreover, the unregulated emissions of polycyclic aromatic hydrocarbons (PAHs), nitroPAHs, hopanes and steranes, alcohols and organic acids, alkanes, carbonyls, dioxins and furans, inorganic ions, metals and elements, elemental carbon, and particle number were substantially (90 to >99%) lower than pre-2007-technology engine emissions, and also substantially (46 to >99%) lower than the 2007-technology engine emissions characterized in the previous study.

Development of Diesel Exhaust Aftertreatment System for Tier II Emissions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yu, R. C.; Cole, A. S., Stroia, B. J.; Huang, S. C.

2002-06-01

Due to their excellent fuel efficiency, reliability, and durability, compression ignition direct injection (CIDI) engines have been used extensively to power almost all highway trucks, urban buses, off-road vehicles, marine carriers, and industrial equipment. CIDI engines burn 35 to 50% less fuel than gasoline engines of comparable size, and they emit far less greenhouse gases (Carbon Dioxides), which have been implicated in global warming. Although the emissions of CIDI engines have been reduced significantly over the last decade, there remains concern with the Nitrogen Oxides (NOX) and Particulate Matter (PM) emission levels. In 2000, the US EPA proposed very stringentmore » emissions standards to be introduced in 2007 along with low sulfur (< 15ppm) diesel fuel. The California Air Resource Board (CARB) has also established the principle that future diesel fueled vehicles should meet the same emissions standards as gasoline fueled vehicles and the EPA followed suit with its Tier II emissions regulations. Meeting the Tier II standards requires NOX and PM emissions to be reduced dramatically. Achieving such low emissions while minimizing fuel economy penalty cannot be done through engine development and fuel reformulation alone, and requires application of NOX and PM aftertreatment control devices. A joint effort was made between Cummins Inc. and the Department of Energy to develop the generic aftertreatment subsystem technologies applicable for Light-Duty Vehicle (LDV) and Light-Duty Truck (LDT) engines. This paper provides an update on the progress of this joint development program. Three NOX reduction technologies including plasmaassisted catalytic NOX reduction (PACR), active lean NOX catalyst (LNC), and adsorber catalyst (AC) technology using intermittent rich conditions for NOX reduction were investigated in parallel in an attempt to select the best NOX control approach for light-duty aftertreatment subsystem integration and development. Investigations included system design and analysis, critical lab/engine experiments, and ranking then selection of NOX control technologies against reliability, up-front cost, fuel economy, service interval/serviceability, and size/weight. The results of the investigations indicate that the best NOX control approach for LDV and LDT applications is a NOX adsorber system. A greater than 83% NOX reduction efficiency is required to achieve 0.07g/mile NOX Tier II vehicle-out emissions. Both active lean NOX and PACR technology are currently not capable of achieving the high conversion efficiency required for Tier II, Bin 5 emissions standards. In this paper, the NOX technology assessment and selection is first reviewed and discussed. Development of the selected NOX technology (NOX adsorber) and PM control are then discussed in more detail. Discussion includes exhaust sulfur management, further adsorber formulation development, reductant screening, diesel particulate filter development & active regeneration, and preliminary test results on the selected integrated SOX trap, NOX adsorber, and diesel particulate filter system over an FTP-75 emissions cycle, and its impact on fuel economy. Finally, the direction of future work for continued advanced aftertreatment technology development is discussed. (SAE Paper SAE-2002-01-1867 © 2002 SAE International. This paper is published on this website with permission from SAE International. As a user of this website, you are permitted to view this paper on-line, download this pdf file and print one copy of this paper at no cost for your use only. The downloaded pdf file and printout of this SAE paper may not be copied, distributed or forwarded to others or for the use of others.)« less

Laboratory evaluation of a reactive baffle approach to NOx control. Final technical report, February-April 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nelson, S.G.; Van Stone, D.A.; Little, R.C.

1993-09-01

Vermiculite, vermiculite coated with magnesia, and activated carbon sorbents have successfully removed NOx (and carbon monoxide and particles) from combustion exhausts in a subscale drone jet engine test cell (JETC), but back pressure so generated elevated the temperature of the JETC and of the engine. The objective of this effort was to explore the feasibility of locating the sorbents in the face of the duct or of baffles parallel to the direction of flow within the ducts. Jet engine test cells (JETCs) are stationary sources of oxides of nitrogen (NOx), soot, and unburned or partially oxidized carbon compounds that formmore » as byproducts of imperfect combustion. Regulation of NOx emissions is being considered for implementation under the Clean Air Act Amendments of 1990. Several principles have been examined as candidate methods to control NOx emissions from JETCs.« less

Reducing Nitrogen Oxide Emissions: 1996 Compliance with Title IV Limits

EIA Publications

1998-01-01

The purpose of this article is to summarize the existing federal nitrogen oxide (Nox) regulations and the 1996 performance of the 239 Title IV generating units. It also reviews the basics of low-Nox burner technology and presents cost and performance data for retrofits at Title IV units.

Lower vehicular primary emissions of NO2 in Europe than assumed in policy projections

NASA Astrophysics Data System (ADS)

Grange, Stuart K.; Lewis, Alastair C.; Moller, Sarah J.; Carslaw, David C.

2017-12-01

Many European countries do not meet legal air quality standards for ambient nitrogen dioxide (NO2) near roads; a problem that has been forecasted to persist to 2030. Although European air quality standards regulate NO2 concentrations, emissions standards for new vehicles instead set limits for NOx—the combination of nitric oxide (NO) and NO2. From around 1990 onwards, the total emissions of NOx declined significantly in Europe, but roadside concentrations of NO2—a regulated species—declined much less than expected. This discrepancy has been attributed largely to the increasing usage of diesel vehicles in Europe and more directly emitted tailpipe NO2. Here we apply a data-filtering technique to 130 million hourly measurements of NOx, NO2 and ozone (O3) from roadside monitoring stations across 61 urban areas in Europe over the period 1990-2015 to estimate the continent-wide trends of directly emitted NO2. We find that the ratio of NO2 to NOx emissions increased from 1995 to around 2010 but has since stabilized at a level that is substantially lower than is assumed in some key emissions inventories. The proportion of NOx now being emitted directly from road transport as NO2 is up to a factor of two smaller than the estimates used in policy projections. We therefore conclude that there may be a faster attainment of roadside NO2 air quality standards across Europe than is currently expected.

40 CFR 86.540-90 - Exhaust sample analysis.

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE HIGHWAY VEHICLES AND ENGINES Emission Regulations for... appropriate, NOX. concentrations of samples. (6) Check zero and span points. If difference is greater than 2...

40 CFR 86.540-90 - Exhaust sample analysis.

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE HIGHWAY VEHICLES AND ENGINES Emission Regulations for... appropriate, NOX. concentrations of samples. (6) Check zero and span points. If difference is greater than 2...

Unexpected slowdown of US pollutant emission reduction in the past decade

PubMed Central

McDonald, Brian C.; Worden, Helen; Worden, John R.; Miyazaki, Kazuyuki; Qu, Zhen; Henze, Daven K.; Jones, Dylan B. A.; Fischer, Emily V.; Zhu, Liye; Boersma, K. Folkert

2018-01-01

Ground and satellite observations show that air pollution regulations in the United States (US) have resulted in substantial reductions in emissions and corresponding improvements in air quality over the last several decades. However, large uncertainties remain in evaluating how recent regulations affect different emission sectors and pollutant trends. Here we show a significant slowdown in decreasing US emissions of nitrogen oxides (NOx) and carbon monoxide (CO) for 2011–2015 using satellite and surface measurements. This observed slowdown in emission reductions is significantly different from the trend expected using US Environmental Protection Agency (EPA) bottom-up inventories and impedes compliance with local and federal agency air-quality goals. We find that the difference between observations and EPA’s NOx emission estimates could be explained by: (i) growing relative contributions of industrial, area, and off-road sources, (ii) decreasing relative contributions of on-road gasoline, and (iii) slower than expected decreases in on-road diesel emissions. PMID:29712822

Experimental Study on Relationship between NOx Emission and Fuel Consumption of a Diesel Engine

NASA Astrophysics Data System (ADS)

Ning, Ping; Liu, Chunjiang; Feng, Zhiqiang; Xia, Yijiang

2018-01-01

For YC6112 diesel engine assembled Delphl model single fuel pump electric controlled, in the premise of not changing its overall unit structure parameters of other systems, three different types of camshaft for single pumps, two kinds of fuel injectors, two types of superchargers and some phase shifting angle of different camshafts were chosen to match with the engine precisely, the experiments under thirteen kinds of working conditions for the engine with different matching were carried out, the change regulation between NOX emission and fuel consumption for the engine with different kinds of configurations was analyzed. The experiment results show the NOX emission and fuel consumption can be reduced greatly by configuring proper camshaft, fuel injectors and superchargers with YC6112 diesel engine.

40 CFR 94.12 - Interim provisions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... differences in testing will not affect NOX emission rates. (g) Flexibility for engines over 560kW... EMISSIONS FROM MARINE COMPRESSION-IGNITION ENGINES General Provisions for Emission Regulations for Compression-Ignition Marine Engines § 94.12 Interim provisions. This section contains provisions that apply...

40 CFR 94.12 - Interim provisions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... differences in testing will not affect NOX emission rates. (g) Flexibility for engines over 560kW...) CONTROL OF EMISSIONS FROM MARINE COMPRESSION-IGNITION ENGINES General Provisions for Emission Regulations for Compression-Ignition Marine Engines § 94.12 Interim provisions. This section contains provisions...

40 CFR 94.12 - Interim provisions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... differences in testing will not affect NOX emission rates. (g) Flexibility for engines over 560kW...) CONTROL OF EMISSIONS FROM MARINE COMPRESSION-IGNITION ENGINES General Provisions for Emission Regulations for Compression-Ignition Marine Engines § 94.12 Interim provisions. This section contains provisions...

40 CFR 94.12 - Interim provisions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... differences in testing will not affect NOX emission rates. (g) Flexibility for engines over 560kW...) CONTROL OF EMISSIONS FROM MARINE COMPRESSION-IGNITION ENGINES General Provisions for Emission Regulations for Compression-Ignition Marine Engines § 94.12 Interim provisions. This section contains provisions...

40 CFR 94.12 - Interim provisions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... differences in testing will not affect NOX emission rates. (g) Flexibility for engines over 560kW...) CONTROL OF EMISSIONS FROM MARINE COMPRESSION-IGNITION ENGINES General Provisions for Emission Regulations for Compression-Ignition Marine Engines § 94.12 Interim provisions. This section contains provisions...

EFFECTS OF ENGINE SPEED AND ACCESSORY LOAD ON IDLING EMISSIONS FROM HEAVY-DUTY DIESEL TRUCK ENGINES

EPA Science Inventory

A nontrivial portion of heavy-duty vehicle emissions of nitrogen oxides (NOx) and particulate matter (PM) occurs during idling. Regulators and the environmental community are interested in curtailing truck idling emissions, but current emissions models do not characterize them ac...

NASA Project Develops Next-Generation Low-Emissions Combustor Technologies

NASA Technical Reports Server (NTRS)

Lee, Chi-Ming; Chang, Clarence T.; Herbon, John T.; Kramer, Stephen K.

2013-01-01

NASA's Environmentally Responsible Aviation (ERA) Project is working with industry to develop the fuel flexible combustor technologies for a new generation of low-emissions engine targeted for the 2020 timeframe. These new combustors will reduce nitrogen oxide (NOx) emissions to half of current state-of-the-art (SOA) combustors, while simultaneously reducing noise and fuel burn. The purpose of the low NOx fuel-flexible combustor research is to advance the Technology Readiness Level (TRL) and Integration Readiness Level (IRL) of a low NOx, fuel flexible combustor to the point where it can be integrated in the next generation of aircraft. To reduce project risk and optimize research benefit NASA chose to found two Phase 1 contracts. The first Phase 1 contracts went to engine manufactures and were awarded to: General Electric Company, and Pratt & Whitney Company. The second Phase 1 contracts went to fuel injector manufactures Goodrich Corporation, Parker Hannifin Corporation, and Woodward Fuel System Technology. In 2012, two sector combustors were tested at NASA's ASCR. The results indicated 75% NOx emission reduction below the 2004 CAEP/6 regulation level.

40 CFR 86.332-79 - Oxides of nitrogen analyzer calibration.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Emission Regulations for New Gasoline-Fueled and Diesel-Fueled Heavy-Duty Engines; Gaseous Exhaust Test.... (2) Zero the oxides of nitrogen analyzer. (3) Connect the outlet of the NOX generator (see Figure D79... operating range. (4) Introduce into the NOX generator-analyzer system a span gas with a NO concentration...

40 CFR 86.332-79 - Oxides of nitrogen analyzer calibration.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Emission Regulations for New Gasoline-Fueled and Diesel-Fueled Heavy-Duty Engines; Gaseous Exhaust Test.... (2) Zero the oxides of nitrogen analyzer. (3) Connect the outlet of the NOX generator (see Figure D79... operating range. (4) Introduce into the NOX generator-analyzer system a span gas with a NO concentration...

40 CFR 75.70 - NOX mass emissions provisions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 17 2012-07-01 2012-07-01 false NOX mass emissions provisions. 75.70... (CONTINUED) CONTINUOUS EMISSION MONITORING NOX Mass Emissions Provisions § 75.70 NOX mass emissions... subpart to the extent that compliance is required by an applicable State or federal NOX mass emission...

Ammonia Generation and Utilization in a Passive SCR (TWC+SCR) System on Lean Gasoline Engine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prikhodko, Vitaly Y.; James E. Parks, II; Pihl, Josh A.

Lean gasoline engines offer greater fuel economy than the common stoichiometric gasoline engine, but the current three way catalyst (TWC) on stoichiometric engines is unable to control nitrogen oxide (NOX) emissions in oxidizing exhaust. For these lean gasoline engines, lean NOX emission control is required to meet existing Tier 2 and upcoming Tier 3 emission regulations set by the U.S. Environmental Protection Agency (EPA). While urea-based selective catalytic reduction (SCR) has proven effective in controlling NOX from diesel engines, the urea storage and delivery components can add significant size and cost. As such, onboard NH 3 production via a passivemore » SCR approach is of interest. In a passive SCR system, NH 3 is generated over a close-coupled TWC during periodic slightly rich engine operation and subsequently stored on an underfloor SCR catalyst. Upon switching to lean operation, NOX passes through the TWC and is reduced by the stored NH 3 on the SCR catalyst. In this work, a passive SCR system was evaluated on a 2.0-liter BMW lean burn gasoline direct injection engine to assess NH 3 generation over a Pd-only TWC and utilization over a Cu-based SCR catalyst. System NOX reduction efficiency and fuel efficiency improvement compared to stoichiometric engine operation were measured. A feedback control strategy based on cumulative NH 3 produced by the TWC during rich operation and NOX emissions during lean operation was implemented on the engine to control lean/rich cycle timing. At an SCR average inlet temperature of 350 °C, an NH 3:NOX ratio of 1.15:1 (achieved through longer rich cycle timing) resulted in 99.7 % NOX conversion. Increasing NH 3 generation further resulted in even higher NOX conversion; however, tailpipe NH 3 emissions resulted. At higher underfloor temperatures, NH 3 oxidation over the SCR limited NH 3 availability for NOX reduction. At the engine conditions studied, greater than 99 % NOX conversion was achieved with passive SCR while delivering fuel efficiency benefits ranging between 6-11 % compared with stoichiometric operation.« less

Ammonia Generation and Utilization in a Passive SCR (TWC+SCR) System on Lean Gasoline Engine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prikhodko, Vitaly Y; Parks, II, James E; Pihl, Josh A

Lean gasoline engines offer greater fuel economy than the common stoichiometric gasoline engine, but the current three-way catalyst (TWC) on stoichiometric engines is unable to control nitrogen oxide (NOX) emissions in the oxygen-rich exhaust. Thus, lean NOX emission control is required to meet existing Tier 2 and upcoming Tier 3 emission regulations set by the U.S. Environmental Protection Agency (EPA). While urea-based selective catalytic reduction (SCR) has proven effective in controlling NOX from diesel engines, the urea storage and delivery components can add significant size and cost. As such, onboard NH3 production via a passive SCR approach is of interest.more » In a passive SCR system, NH3 is generated over a close-coupled TWC during periodic slightly rich engine operation and subsequently stored on an underfloor SCR catalyst. Upon switching to lean operation, NOX passes through the TWC and is reduced by the stored NH3 on the SCR catalyst. In this work, a passive SCR system was evaluated on a 2.0-liter BMW lean burn gasoline direct injection engine to assess NH3 generation over a Pd-only TWC and utilization over a Cu-based SCR catalyst. System NOX reduction efficiency and fuel efficiency improvement compared to stoichiometric engine operation were measured. A feedback control strategy based on cumulative NH3 produced by the TWC during rich operation and NOX emissions during lean operation was implemented on the engine to control lean/rich cycle timing. 15% excess NH3 production over a 1:1 NH3:NOX ratio was required (via longer rich cycle timing) to achieve 99.7% NOX conversion at an SCR average inlet temperature of 350 C. Increasing NH3 generation further resulted in even higher NOX conversion; however, tailpipe NH3 emissions resulted. At higher temperatures, NH3 oxidation becomes important and limits NH3 availability for NOX reduction. At the engine conditions studied here, greater than 99% NOX conversion was achieved with passive SCR while delivering fuel efficiency benefits ranging between 6-11% compared with stoichiometric operation.« less

Ammonia Generation and Utilization in a Passive SCR (TWC+SCR) System on Lean Gasoline Engine

DOE PAGES

Prikhodko, Vitaly Y.; James E. Parks, II; Pihl, Josh A.; ...

2016-04-05

Lean gasoline engines offer greater fuel economy than the common stoichiometric gasoline engine, but the current three way catalyst (TWC) on stoichiometric engines is unable to control nitrogen oxide (NOX) emissions in oxidizing exhaust. For these lean gasoline engines, lean NOX emission control is required to meet existing Tier 2 and upcoming Tier 3 emission regulations set by the U.S. Environmental Protection Agency (EPA). While urea-based selective catalytic reduction (SCR) has proven effective in controlling NOX from diesel engines, the urea storage and delivery components can add significant size and cost. As such, onboard NH 3 production via a passivemore » SCR approach is of interest. In a passive SCR system, NH 3 is generated over a close-coupled TWC during periodic slightly rich engine operation and subsequently stored on an underfloor SCR catalyst. Upon switching to lean operation, NOX passes through the TWC and is reduced by the stored NH 3 on the SCR catalyst. In this work, a passive SCR system was evaluated on a 2.0-liter BMW lean burn gasoline direct injection engine to assess NH 3 generation over a Pd-only TWC and utilization over a Cu-based SCR catalyst. System NOX reduction efficiency and fuel efficiency improvement compared to stoichiometric engine operation were measured. A feedback control strategy based on cumulative NH 3 produced by the TWC during rich operation and NOX emissions during lean operation was implemented on the engine to control lean/rich cycle timing. At an SCR average inlet temperature of 350 °C, an NH 3:NOX ratio of 1.15:1 (achieved through longer rich cycle timing) resulted in 99.7 % NOX conversion. Increasing NH 3 generation further resulted in even higher NOX conversion; however, tailpipe NH 3 emissions resulted. At higher underfloor temperatures, NH 3 oxidation over the SCR limited NH 3 availability for NOX reduction. At the engine conditions studied, greater than 99 % NOX conversion was achieved with passive SCR while delivering fuel efficiency benefits ranging between 6-11 % compared with stoichiometric operation.« less

Modeled and observed ozone sensitivity to mobile-source emissions in Mexico City

NASA Astrophysics Data System (ADS)

Zavala, M.; Lei, W.; Molina, M. J.; Molina, L. T.

2009-01-01

The emission characteristics of mobile sources in the Mexico City Metropolitan Area (MCMA) have changed significantly over the past few decades in response to emission control policies, advancements in vehicle technologies and improvements in fuel quality, among others. Along with these changes, concurrent non-linear changes in photochemical levels and criteria pollutants have been observed, providing a unique opportunity to understand the effects of perturbations of mobile emission levels on the photochemistry in the region using observational and modeling approaches. The observed historical trends of ozone (O3), carbon monoxide (CO) and nitrogen oxides (NOx) suggest that ozone production in the MCMA has changed from a low to a high VOC-sensitive regime over a period of 20 years. Comparison of the historical emission trends of CO, NOx and hydrocarbons derived from mobile-source emission studies in the MCMA from 1991 to 2006 with the trends of the concentrations of CO, NOx, and the CO/NOx ratio during peak traffic hours also indicates that fuel-based fleet average emission factors have significantly decreased for CO and VOCs during this period whereas NOx emission factors do not show any strong trend, effectively reducing the ambient VOC/NOx ratio. This study presents the results of model analyses on the sensitivity of the observed ozone levels to the estimated historical changes in its precursors. The model sensitivity analyses used a well-validated base case simulation of a high pollution episode in the MCMA with the mathematical Decoupled Direct Method (DDM) and the standard Brute Force Method (BFM) in the 3-D CAMx chemical transport model. The model reproduces adequately the observed historical trends and current photochemical levels. Comparison of the BFM and the DDM sensitivity techniques indicates that the model yields ozone values that increase linearly with NOx emission reductions and decrease linearly with VOC emission reductions only up to 30% from the base case. We further performed emissions perturbations from the gasoline fleet, diesel fleet, all mobile (gasoline plus diesel) and all emission sources (anthropogenic plus biogenic). The results suggest that although large ozone reductions obtained in the past were from changes in emissions from gasoline vehicles, currently significant benefits could be achieved with additional emission control policies directed to regulation of VOC emissions from diesel and area sources that are high emitters of alkenes, aromatics and aldehydes.

Modeled and observed ozone sensitivity to mobile-source emissions in Mexico City

NASA Astrophysics Data System (ADS)

Zavala, M.; Lei, W. F.; Molina, M. J.; Molina, L. T.

2008-08-01

The emission characteristics of mobile sources in the Mexico City Metropolitan Area (MCMA) have changed significantly over the past few decades in response to emission control policies, advancements in vehicle technologies and improvements in fuel quality, among others. Along with these changes, concurrent non-linear changes in photochemical levels and criteria pollutants have been observed, providing a unique opportunity to understand the effects of perturbations of mobile emission levels on the photochemistry in the region using observational and modeling approaches. The observed historical trends of ozone (O3), carbon monoxide (CO) and nitrogen oxides (NOx) suggest that ozone production in the MCMA has changed from a low to a high VOC-sensitive regime over a period of 20 years. Comparison of the historical emission trends of CO, NOx and hydrocarbons derived from mobile-source emission studies in the MCMA from 1991 to 2006 with the trends of the concentrations of CO, NOx, and the CO/NOx ratio during peak traffic hours also indicates that fuel-based fleet average emission factors have significantly decreased for CO and VOCs during this period whereas NOx emission factors do not show any strong trend, effectively reducing the ambient VOC/NOx ratio. This study presents the results of model analyses on the sensitivity of the observed ozone levels to the estimated historical changes in its precursors. The model sensitivity analyses used a well-validated base case simulation of a high pollution episode in the MCMA with the mathematical Decoupled Direct Method (DDM) and the standard Brute Force Method (BFM) in the 3-D CAMx chemical transport model. The model reproduces adequately the observed historical trends and current photochemical levels. Comparison of the BFM and the DDM sensitivity techniques indicates that the model yields ozone values that increase linearly with NOx emission reductions and decrease linearly with VOC emission reductions only up to 30% from the base case. We further performed emissions perturbations from the gasoline fleet, diesel fleet, all mobile (gasoline plus diesel) and all emission sources (anthropogenic plus biogenic). The results suggest that although large ozone reductions obtained in the past were from changes in emissions from gasoline vehicles, currently significant benefits could be achieved with additional emission control policies directed to regulation of VOC emissions from diesel and area sources that are high emitters of alkenes, aromatics and aldehydes.

Regulating low-NOx and high-burnout deep-air-staging combustion under real-furnace conditions in a 600 MWe down-fired supercritical boiler by strengthening the staged-air effect.

PubMed

Kuang, Min; Wang, Zhihua; Zhu, Yanqun; Ling, Zhongqian; Li, Zhengqi

2014-10-21

A 600 MW(e) down-fired pulverized-coal supercritical boiler, which was equipped with a deep-air-staging combustion system for reducing the particularly high NOx emissions, suffered from the well-accepted contradiction between low NOx emissions and high carbon in fly ash, in addition to excessively high gas temperatures in the hopper that jeopardized the boiler's safe operations. Previous results uncovered that under low-NOx conditions, strengthening the staged-air effect by decreasing the staged-air angle and simultaneously increasing the staged-air damper opening alleviated the aforementioned problems to some extent. To establish low-NOx and high-burnout circumstances and control the aforementioned hopper temperatures, a further staged-air retrofit with horizontally redirecting staged air through an enlarged staged-air slot area was performed to greatly strengthen the staged-air effect. Full-load industrial-size measurements were performed to confirm the availability of this retrofit. The present data were compared with those published results before the retrofit. High NOx emissions, low carbon in fly ah, and high hopper temperatures (i.e., levels of 1036 mg/m(3) at 6% O2, 3.72%, and about 1300 °C, respectively) appeared under the original conditions with the staged-air angle of 45° and without overfire air (OFA) application. Applying OFA and reducing the angle to 20° achieved an apparent NOx reduction and a moderate hopper temperature decrease while a sharp increase in carbon in fly ash (i.e., levels of 878 mg/m(3) at 6% O2, about 1200 °C, and 9.81%, respectively). Fortunately, the present staged-air retrofit was confirmed to be applicable in regulating low-NOx, high-burnout, and low hopper temperature circumstances (i.e., levels of 867 mg/m(3) at 6% O2, 5.40%, and about 1100 °C, respectively).

Characteristics of NOx emission from Chinese coal-fired power plants equipped with new technologies

NASA Astrophysics Data System (ADS)

Ma, Zizhen; Deng, Jianguo; Li, Zhen; Li, Qing; Zhao, Ping; Wang, Liguo; Sun, Yezhu; Zheng, Hongxian; Pan, Li; Zhao, Shun; Jiang, Jingkun; Wang, Shuxiao; Duan, Lei

2016-04-01

Coal combustion in coal-fired power plants is one of the important anthropogenic NOx sources, especially in China. Many policies and methods aiming at reducing pollutants, such as increasing installed capacity and installing air pollution control devices (APCDs), especially selective catalytic reduction (SCR) units, could alter NOx emission characteristics (NOx concentration, NO2/NOx ratio, and NOx emission factor). This study reported the NOx characteristics of eight new coal-fired power-generating units with different boiler patterns, installed capacities, operating loads, and coal types. The results showed that larger units produced less NOx, and anthracite combustion generated more NOx than bitumite and lignite combustion. During formation, the NOx emission factors varied from 1.81 to 6.14 g/kg, much lower than those of older units at similar scales. This implies that NOx emissions of current and future units could be overestimated if they are based on outdated emission factors. In addition, APCDs, especially SCR, greatly decreased NOx emissions, but increased NO2/NOx ratios. Regardless, the NO2/NOx ratios were lower than 5%, in accordance with the guidelines and supporting the current method for calculating NOx emissions from coal-fired power plants that ignore NO2.

Enhanced Combustion Low NOx Pulverized Coal Burner

DOE Office of Scientific and Technical Information (OSTI.GOV)

David Towle; Richard Donais; Todd Hellewell

2007-06-30

For more than two decades, Alstom Power Inc. (Alstom) has developed a range of low cost, infurnace technologies for NOx emissions control for the domestic U.S. pulverized coal fired boiler market. This includes Alstom's internally developed TFS 2000{trademark} firing system, and various enhancements to it developed in concert with the U.S. Department of Energy. As of the date of this report, more than 270 units representing approximately 80,000 MWe of domestic coal fired capacity have been retrofit with Alstom low NOx technology. Best of class emissions range from 0.18 lb/MMBtu for bituminous coal to 0.10 lb/MMBtu for subbituminous coal, withmore » typical levels at 0.24 lb/MMBtu and 0.13 lb/MMBtu, respectively. Despite these gains, NOx emissions limits in the U.S. continue to ratchet down for new and existing boiler equipment. On March 10, 2005, the Environmental Protection Agency (EPA) announced the Clean Air Interstate Rule (CAIR). CAIR requires 25 Eastern states to reduce NOx emissions from the power generation sector by 1.7 million tons in 2009 and 2.0 million tons by 2015. Low cost solutions to meet such regulations, and in particular those that can avoid the need for a costly selective catalytic reduction system (SCR), provide a strong incentive to continue to improve low NOx firing system technology to meet current and anticipated NOx control regulations. The overall objective of the work is to develop an enhanced combustion, low NOx pulverized coal burner, which, when integrated with Alstom's state-of-the-art, globally air staged low NOx firing systems will provide a means to achieve: Less than 0.15 lb/MMBtu NOx emissions when firing a high volatile Eastern or Western bituminous coal, Less than 0.10 lb/MMBtu NOx emissions when firing a subbituminous coal, NOx reduction costs at least 25% lower than the costs of an SCR, Validation of the NOx control technology developed through large (15 MWt) pilot scale demonstration, and Documentation required for economic evaluation and commercial application. During the project performance period, Alstom performed computational fluid dynamics (CFD) modeling and large pilot scale combustion testing in its Industrial Scale Burner Facility (ISBF) at its U.S. Power Plant Laboratories facility in Windsor, Connecticut in support of these objectives. The NOx reduction approach was to optimize near-field combustion to ensure that minimum NOx emissions are achieved with minimal impact on unburned carbon in ash, slagging and fouling, corrosion, and flame stability/turn-down. Several iterations of CFD and combustion testing on a Midwest coal led to an optimized design, which was extensively combustion tested on a range of coals. The data from these tests were then used to validate system costs and benefits versus SCR. Three coals were evaluated during the bench-scale and large pilot-scale testing tasks. The three coals ranged from a very reactive subbituminous coal to a moderately reactive Western bituminous coal to a much less reactive Midwest bituminous coal. Bench-scale testing was comprised of standard ASTM properties evaluation, plus more detailed characterization of fuel properties through drop tube furnace testing and thermogravimetric analysis. Bench-scale characterization of the three test coals showed that both NOx emissions and combustion performance are a strong function of coal properties. The more reactive coals evolved more of their fuel bound nitrogen in the substoichiometric main burner zone than less reactive coal, resulting in the potential for lower NOx emissions. From a combustion point of view, the more reactive coals also showed lower carbon in ash and CO values than the less reactive coal at any given main burner zone stoichiometry. According to bench-scale results, the subbituminous coal was found to be the most amenable to both low NOx, and acceptably low combustibles in the flue gas, in an air staged low NOx system. The Midwest bituminous coal, by contrast, was predicted to be the most challenging of the three coals, with the Western bituminous coal predicted to behave in-between the subbituminous coal and the Midwest bituminous coal. CFD modeling was used to gain insight into the mechanisms governing nozzle tip performance with respect to NOx emissions. The CFD simulations were run as steady state, turbulent, non-reacting flow with heat transfer and focused on predicting the near field mixing and particle dispersion rates. CFD results were used to refine the proposed tip concepts before they were built, as well as to help identify and evaluate possible improvements to the tips for subsequent test weeks.« less

Characteristics of typical non-road machinery emissions in China by using portable emission measurement system.

PubMed

Fu, Mingliang; Ge, Yunshan; Tan, Jianwei; Zeng, Tao; Liang, Bin

2012-10-15

Non-road machinery, especially construction equipment could be an important pollutant source of the deterioration in air quality in Chinese urban areas due to its large quantity and to the absence of stringent emission requirements. In this study, emission tests were performed on 12 excavators and 8 wheel loaders by using portable emission measurement system (PEMS) to determine their emission characteristics. The typical operating modes were categorized as idling mode, moving mode and working mode. Compared with those during idling and moving modes, the average time-based emission factors during working mode of HC were 2.61 and 1.27 times higher, NO(x) were 3.66 and 1.36 times higher, and PM were 4.05 and 1.95 times higher, respectively. Under all conditions, categories of the measured emissions increased with the rise in engine power. Compared with those of Stage I emission standard equipment, gaseous emissions and PM emitted from Stage II emission standard equipment were lower. The results indicated that, from Stage I to Stage II, the average reductions of HC, NO(x) and PM were 56%, 37% and 29% for the working mode, respectively. Those results also demonstrated the effectiveness of emission control regulation and the improvement of emission control technology. The data and tests show that the longer the accumulated working hours, the higher HC and NO(x) average fuel-based emission factors are. The emissions measured from the construction vehicles employed in this study were higher than the data collected in previous studies, which shows that it is critical for the government to put into effect more stringent emission regulations to further improve the air quality in Chinese urban areas. Copyright © 2012 Elsevier B.V. All rights reserved.

On-vehicle emission measurement of a light-duty diesel van at various speeds at high altitude

NASA Astrophysics Data System (ADS)

Wang, Xin; Yin, Hang; Ge, Yunshan; Yu, Linxiao; Xu, Zhenxian; Yu, Chenglei; Shi, Xuejiao; Liu, Hongkun

2013-12-01

As part of the research on the relationship between the speed of a vehicle operating at high altitude and its contaminant emissions, an on-vehicle emission measurement of a light-duty diesel van at the altitudes of 1000 m, 2400 m and 3200 m was conducted. The test vehicle was a 2.8 L turbocharged diesel Ford Transit. Its settings were consistent in all experiments. Regulated gaseous emissions, including CO, HC and NOx, together with particulate matter was measured at nine speeds ranged from 10 km h-1 to 90 km h-1 with 10 km h-1 intervals settings. At each speed, measurement lasted for at least 120 s to ensure the sufficiency and reliability of the collected data. The results demonstrated that at all altitudes, CO and HC emissions decreased as the vehicle speed increased. However both NOx and PM increased with vehicle speed. In terms of the effects of altitude, an increase in CO, HC and PM was observed with the rising of altitude at each vehicle speed. NOx behaved different: emission of NOx initially increased as the vehicle was raised from 1000 m to 2400 m, but it decreased when the vehicle was further elevated to 3200 m.

Design and testing of an independently controlled urea SCR retrofit system for the reduction of NOx emissions from marine diesels.

PubMed

Johnson, Derek R; Bedick, Clinton R; Clark, Nigel N; McKain, David L

2009-05-15

Diesel engine emissions for on-road, stationary and marine applications are regulated in the United States via standards set by the Environmental Protection Agency (EPA). A major component of diesel exhaust that is difficult to reduce is nitrogen oxides (NOx). Selective catalytic reduction (SCR) has been in use for many years for stationary applications, including external combustion boilers, and is promising for NOx abatement as a retrofit for mobile applications where diesel compression ignition engines are used. The research presented in this paper is the first phase of a program focused on the reduction of NOx by use of a stand-alone urea injection system, applicable to marine diesel engines typical of work boats (e.g., tugs). Most current urea SCR systems communicate with engine controls to predict NOx emissions based on signals such as torque and engine speed, however many marine engines in use still employ mechanical injection technology and lack electronic communication abilities. The system developed and discussed in this paper controls NOx emissions independentof engine operating parameters and measures NOx and exhaust flow using the following exhaust sensor inputs: absolute pressure, differential pressure, temperature, and NOx concentration. These sensor inputs were integrated into an independent controller and open loop architecture to estimate the necessary amount of urea needed, and the controller uses pulse width modulation (PWM) to power an automotive fuel injector for airless urea delivery. The system was tested in a transient test cell on a 350 hp engine certified at 4 g/bhp-hr of NOx, with a goal of reducing the engine out NOx levels by 50%. NOx reduction capabilities of 41-67% were shown on the non road transient cycle (NRTC) and ICOMIA E5 steady state cycles with system optimization during testing to minimize the dilute ammonia slip to cycle averages of 5-7 ppm. The goal of 50% reduction of NOx can be achieved dependent upon cycle. Further research with control optimization, urea distribution and possible use of oxidation catalysts is recommended to improve the NOx reduction capabilities while minimizing ammonia slip.

Regulated and unregulated emissions from modern 2010 emissions-compliant heavy-duty on-highway diesel engines

PubMed Central

Khalek, Imad A.; Blanks, Matthew G.; Merritt, Patrick M.; Zielinska, Barbara

2015-01-01

The U.S. Environmental Protection Agency (EPA) established strict regulations for highway diesel engine exhaust emissions of particulate matter (PM) and nitrogen oxides (NOx) to aid in meeting the National Ambient Air Quality Standards. The emission standards were phased in with stringent standards for 2007 model year (MY) heavy-duty engines (HDEs), and even more stringent NOX standards for 2010 and later model years. The Health Effects Institute, in cooperation with the Coordinating Research Council, funded by government and the private sector, designed and conducted a research program, the Advanced Collaborative Emission Study (ACES), with multiple objectives, including detailed characterization of the emissions from both 2007- and 2010-compliant engines. The results from emission testing of 2007-compliant engines have already been reported in a previous publication. This paper reports the emissions testing results for three heavy-duty 2010-compliant engines intended for on-highway use. These engines were equipped with an exhaust diesel oxidation catalyst (DOC), high-efficiency catalyzed diesel particle filter (DPF), urea-based selective catalytic reduction catalyst (SCR), and ammonia slip catalyst (AMOX), and were fueled with ultra-low-sulfur diesel fuel (~6.5 ppm sulfur). Average regulated and unregulated emissions of more than 780 chemical species were characterized in engine exhaust under transient engine operation using the Federal Test Procedure cycle and a 16-hr duty cycle representing a wide dynamic range of real-world engine operation. The 2010 engines’ regulated emissions of PM, NOX, nonmethane hydrocarbons, and carbon monoxide were all well below the EPA 2010 emission standards. Moreover, the unregulated emissions of polycyclic aromatic hydrocarbons (PAHs), nitroPAHs, hopanes and steranes, alcohols and organic acids, alkanes, carbonyls, dioxins and furans, inorganic ions, metals and elements, elemental carbon, and particle number were substantially (90 to >99%) lower than pre-2007-technology engine emissions, and also substantially (46 to >99%) lower than the 2007-technology engine emissions characterized in the previous study. Implications: Heavy-duty on-highway diesel engines equipped with DOC/DPF/SCR/AMOX and fueled with ultra-low-sulfur diesel fuel produced lower emissions than the stringent 2010 emission standards established by the U.S. Environmental Protection Agency. They also resulted in significant reductions in a wide range of unregulated toxic emission compounds relative to older technology engines. The increased use of newer technology (2010+) diesel engines in the on-highway sector and the adaptation of such technology by other sectors such as nonroad, displacing older, higher emissions engines, will have a positive impact on ambient levels of PM, NOx, and volatile organic compounds, in addition to many other toxic compounds. PMID:26037832

Experimental investigation on regulated and unregulated emissions of a diesel/methanol compound combustion engine with and without diesel oxidation catalyst.

PubMed

Zhang, Z H; Cheung, C S; Chan, T L; Yao, C D

2010-01-15

The use of methanol in combination with diesel fuel is an effective measure to reduce particulate matter (PM) and nitrogen oxides (NOx) emissions from in-use diesel vehicles. In this study, a diesel/methanol compound combustion (DMCC) scheme was proposed and a 4-cylinder naturally-aspirated direct-injection diesel engine modified to operate on the proposed combustion scheme. The effect of DMCC and diesel oxidation catalyst (DOC) on the regulated emissions of total hydrocarbons (THC), carbon monoxide (CO), NOx and PM was investigated based on the Japanese 13 Mode test cycle. Certain unregulated emissions, including methane, ethyne, ethene, 1,3-butadiene, BTX (benzene, toluene, xylene), unburned methanol and formaldehyde were also evaluated based on the same test cycle. In addition, the soluble organic fraction (SOF) in the particulate and the particulate number concentration and size distribution were investigated at certain selected modes of operation. The results show that the DMCC scheme can effectively reduce NOx, particulate mass and number concentrations, ethyne, ethene and 1,3-butadiene emissions but significantly increase the emissions of THC, CO, NO(2), BTX, unburned methanol, formaldehyde, and the proportion of SOF in the particles. After the DOC, the emission of THC, CO, NO(2), as well as the unregulated gaseous emissions, can be significantly reduced when the exhaust gas temperature is sufficiently high while the particulate mass concentration is further reduced due to oxidation of the SOF. Copyright 2009 Elsevier B.V. All rights reserved.

Vehicle NOx emission plume isotopic signatures: Spatial variability across the eastern United States

NASA Astrophysics Data System (ADS)

Miller, David J.; Wojtal, Paul K.; Clark, Sydney C.; Hastings, Meredith G.

2017-04-01

On-road vehicle nitrogen oxide (NOx) sources currently dominate the U.S. anthropogenic emission budgets, yet vehicle NOx emissions have uncertain contributions to oxidized nitrogen (N) deposition patterns. Isotopic signatures serve as a potentially valuable observational tool to trace source contributions to NOx chemistry and N deposition, yet in situ emission signatures are underconstrained. We characterize the spatiotemporal variability of vehicle NOx emission isotopic signatures (δ15N-NOx) representative of U.S. vehicle fleet-integrated emission plumes. A novel combination of on-road mobile and stationary urban measurements is performed using a field and laboratory-verified technique for actively capturing NOx in solution to quantify δ15N-NOx at hourly resolution. On-road δ15N-NOx upwind of Providence, RI, ranged from -7 to -3‰. Simultaneous urban background δ15N-NOx observations showed comparable range and variations with on-road measurements, suggesting that vehicles dominate NOx emissions in the Providence area. On-road spatial δ15N-NOx variations of -9 to -2‰ were observed under various driving conditions in six urban metropolitan areas and rural interstate highways during summer and autumn in the U.S. Northeast and Midwest. Although isotopic signatures were insensitive to on-road driving mode variations, statistically significant correlations were found between δ15N-NOx and NOx emission factor extremes associated with heavy diesel emitter contributions. Overall, these results constrain an isotopic signature of fleet-integrated roadway NOx emission plumes, which have important implications for distinguishing vehicle NOx from other sources and tracking emission contributions to NOx chemistry and N deposition.

40 CFR 75.19 - Optional SO2, NOX, and CO2 emissions calculation for low mass emissions (LME) units.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (or group of identical units) equipped with SCR (or SNCR) and uses dry low-NOX technology to control... with add-on NOX emission controls, and for units that use dry low-NOX technology, the owner or operator... mass emissions unit that uses dry low-NOX premix technology to control NOX emissions, proper operation...

Impact of a future H2 transportation on atmospheric pollution in Europe

NASA Astrophysics Data System (ADS)

Popa, M. E.; Segers, A. J.; Denier van der Gon, H. A. C.; Krol, M. C.; Visschedijk, A. J. H.; Schaap, M.; Röckmann, T.

2015-07-01

Hydrogen (H2) is being explored as a fuel for passenger vehicles; it can be used in fuel cells to power electric motors or burned in internal combustion engines. In order to evaluate the potential influence of a future H2-based road transportation on the regional air quality in Europe, we implemented H2 in the atmospheric transport and chemistry model LOTOS-EUROS. We simulated the present and future (2020) air quality, using emission scenarios with different proportions of H2 vehicles and different H2 leakage rates. The reference future scenario does not include H2 vehicles, and assumes that all present and planned European regulations for emissions are fully implemented. We find that, in general, the air quality in 2020 is significantly improved compared to the current situation in all scenarios, with and without H2 cars. In the future scenario without H2 cars, the pollution is reduced due to the strict European regulations: annually averaged CO, NOx and PM2.5 over the model domain decrease by 15%, 30% and 20% respectively. The additional improvement brought by replacing 50% or 100% of traditionally-fueled vehicles by H2 vehicles is smaller in absolute terms. If 50% of vehicles are using H2, the CO, NOx and PM2.5 decrease by 1%, 10% and 1% respectively, compared to the future scenario without H2 cars. When all vehicles run on H2, then additional decreases in CO, NOx and PM2.5 are 5%, 40%, and 5% relative to the no-H2 cars future scenario. Our study shows that H2 vehicles may be an effective pathway to fulfill the strict future EU air quality regulations. O3 has a more complicated behavior - its annual average decreases in background areas, but increases in the high-NOx area in western Europe, with the decrease in NOx. A more detailed analysis shows that the population exposure to high O3 levels decreases nevertheless. In all future scenarios, traffic emissions account for only a small proportion of the total anthropogenic emissions, thus it becomes more important to better regulate emissions of non-traffic sectors. Although atmospheric H2 increases significantly in the high-leakage scenarios considered, the additional H2 added into the atmosphere does not have a significant effect on the ground level air pollution in Europe.

DIESEL ENGINE EFFICIENCY AND EMISSIONS IMPROVEMENT VIA PISTON TEMPERATURE CONTROL - PHASE I

EPA Science Inventory

Using Extractive FTIR to Measure N2O from Medium Heavy ...

EPA Pesticide Factsheets

This pilot project was designed to confirm that an FTIR could generate useful real-time data for non-regulated tailpipe emissions of concern to the EPA. This ability to generate useful modal data could be demonstrated if the mode shapes of regulated emissions measured by reference methods corroborated the mode shapes generated by the FTIR. For this purpose comparisons were to be made to CO2 and NOx. The purpose of this study was to determine whether the FTIR could be useful in better understanding the conditions under which N2O was emitted from the tailpipe. The study was designed to see whether there was correlation of the CO2 and NOx emissions as measured by CEMs and measured by the FTIR as well as the mode shapes of the real time data

Constraints on Eurasian ship NOx emissions using OMI NO2 observations and GEOS-Chem

NASA Astrophysics Data System (ADS)

Vinken, Geert C. M.; Boersma, Folkert; van Donkelaar, Aaron; Zhang, Lin

2013-04-01

Ships emit large quantities of nitrogen oxides (NOx = NO + NO2), important precursors for ozone (O3) and particulate matter formation. Ships burn low-grade marine heavy fuel due to the limited regulations that exist for the maritime sector in international waters. Previous studies showed that global ship NOx emission inventories amount to 3.0-10.4 Tg N per year (15-30% of total NOx emissions), with most emissions close to land and affecting air quality in densely populated coastal regions. Bottom-up inventories depend on the extrapolation of a relatively small number of measurements that are often unable to capture annual emission changes and can suffer from large uncertainties. Satellites provide long-term, high-resolution retrievals that can be used to improve emission estimates. In this study we provide top-down constraints on ship NOx emissions in major European ship routes, using observed NO2 columns from the Ozone Monitoring Instrument (OMI) and NO2 columns simulated with the nested (0.5°×0.67°) version of the GEOS-Chem chemistry transport model. We use a plume-in-grid treatment of ship NOx emissions to account for in-plume chemistry in our model. We ensure consistency between the retrievals and model simulations by using the high-resolution GEOS-Chem NO2 profiles as a priori. We find evidence that ship emissions in the Mediterranean Sea are geographically misplaced by up to 150 km and biased high by a factor of 4 as compared to the most recent (EMEP) ship emission inventory. Better agreement is found over the shipping lane between Spain and the English Channel. We extend our approach and also provide constraints for major ship routes in the Red Sea and Indian Ocean. Using the full benefit of the long-term retrieval record of OMI, we present a new Eurasian ship emission inventory for the years 2005 to 2010, based on the EMEP and AMVER-ICOADS inventories, and top-down constraints from the satellite retrievals. Our work shows that satellite retrievals can improve the characterization of emission locations, magnitudes and trends over sparsely monitored areas such as seas or oceans.

Top-down quantification of NOx emissions from traffic in an urban area using a high-resolution regional atmospheric chemistry model

NASA Astrophysics Data System (ADS)

Kuik, Friderike; Kerschbaumer, Andreas; Lauer, Axel; Lupascu, Aurelia; von Schneidemesser, Erika; Butler, Tim M.

2018-06-01

With NO2 limit values being frequently exceeded in European cities, complying with the European air quality regulations still poses a problem for many cities. Traffic is typically a major source of NOx emissions in urban areas. High-resolution chemistry transport modelling can help to assess the impact of high urban NOx emissions on air quality inside and outside of urban areas. However, many modelling studies report an underestimation of modelled NOx and NO2 compared with observations. Part of this model bias has been attributed to an underestimation of NOx emissions, particularly in urban areas. This is consistent with recent measurement studies quantifying underestimations of urban NOx emissions by current emission inventories, identifying the largest discrepancies when the contribution of traffic NOx emissions is high. This study applies a high-resolution chemistry transport model in combination with ambient measurements in order to assess the potential underestimation of traffic NOx emissions in a frequently used emission inventory. The emission inventory is based on officially reported values and the Berlin-Brandenburg area in Germany is used as a case study. The WRF-Chem model is used at a 3 km × 3 km horizontal resolution, simulating the whole year of 2014. The emission data are downscaled from an original resolution of ca. 7 km × 7 km to a resolution of 1 km × 1 km. An in-depth model evaluation including spectral decomposition of observed and modelled time series and error apportionment suggests that an underestimation in traffic emissions is likely one of the main causes of the bias in modelled NO2 concentrations in the urban background, where NO2 concentrations are underestimated by ca. 8 µg m-3 (-30 %) on average over the whole year. Furthermore, a diurnal cycle of the bias in modelled NO2 suggests that a more realistic treatment of the diurnal cycle of traffic emissions might be needed. Model problems in simulating the correct mixing in the urban planetary boundary layer probably play an important role in contributing to the model bias, particularly in summer. Also taking into account this and other possible sources of model bias, a correction factor for traffic NOx emissions of ca. 3 is estimated for weekday daytime traffic emissions in the core urban area, which corresponds to an overall underestimation of traffic NOx emissions in the core urban area of ca. 50 %. Sensitivity simulations for the months of January and July using the calculated correction factor show that the weekday model bias can be improved from -8.8 µg m-3 (-26 %) to -5.4 µg m-3 (-16 %) in January on average in the urban background, and -10.3 µg m-3 (-46 %) to -7.6 µg m-3 (-34 %) in July. In addition, the negative bias of weekday NO2 concentrations downwind of the city in the rural and suburban background can be reduced from -3.4 µg m-3 (-12 %) to -1.2 µg m-3 (-4 %) in January and from -3.0 µg m-3 (-22 %) to -1.9 µg m-3 (-14 %) in July. The results and their consistency with findings from other studies suggest that more research is needed in order to more accurately understand the spatial and temporal variability in real-world NOx emissions from traffic, and apply this understanding to the inventories used in high-resolution chemical transport models.

Experimental study on the particulate matter and nitrogenous compounds from diesel engine retrofitted with DOC+CDPF+SCR

NASA Astrophysics Data System (ADS)

Zhang, Yunhua; Lou, Diming; Tan, Piqiang; Hu, Zhiyuan

2018-03-01

The increasingly stringent emission regulations will mandate the retrofit of after-treatment devices for in-use diesel vehicles, in order to reduce their substantial particulate matter and nitrogen oxides (NOX) emissions. In this paper, a combination of DOC (diesel oxidation catalyst), CDPF (catalytic diesel particulate filter) and SCR (selective catalytic reduction) retrofit for a heavy-duty diesel engine was employed to perform experiment on the engine test bench to evaluate the effects on the particulate matter emissions including particle number (PN), particle mass (PM), particle size distributions and nitrogenous compounds emissions including NOX, nitrogen dioxide (NO2)/NOX, nitrous oxide (N2O) and ammonia (NH3) slip. In addition, the urea injection was also of our concern. The results showed that the DOC+CDPF+SCR retrofit almost had no adverse effect on the engine power and fuel consumption. Under the test loads, the upstream DOC and CDPF reduced the PN and PM by an average of 91.6% and 90.9%, respectively. While the downstream SCR brought about an average decrease of 85% NOX. Both PM and NOX emission factors based on this retrofit were lower than China-Ⅳ limits (ESC), and even lower than China-Ⅴ limits (ESC) at medium and high loads. The DOC and CDPF changed the particle size distributions, leading to the increase in the proportion of accumulation mode particles and the decrease in the percentage of nuclear mode particles. This indicates that the effect of DOC and CDPF on nuclear mode particles was better than that of accumulation mode ones. The upstream DOC could increase the NO2/NOX ratio to 40%, higher NO2/NOX ratio improved the efficiency of CDPF and SCR. Besides, the N2O emission increased by an average of 2.58 times after the retrofit and NH3 slip occurred with the average of 26.7 ppm. The rate of urea injection was roughly equal to 8% of the fuel consumption rate. The DOC+CDPF+SCR retrofit was proved a feasible and effective measurement in terms of reducing particulate emissions and NOX simultaneously for in-use engine. However, it also resulted in higher N2O emission, NH3 slip as well as urea injecting strategy problem which should be of further concern.

40 CFR 1068.101 - What general actions does this regulation prohibit?

Code of Federal Regulations, 2014 CFR

2014-07-01

..., operating an engine without a supply of appropriate quality urea if the emissions control system relies on urea to reduce NOx emissions or the use of incorrect fuel or engine oil that renders the emissions... manufacturers of new engines, manufacturers of equipment containing these engines, and manufacturers of new...

40 CFR 1068.101 - What general actions does this regulation prohibit?

Code of Federal Regulations, 2012 CFR

2012-07-01

..., operating an engine without a supply of appropriate quality urea if the emissions control system relies on urea to reduce NOx emissions or the use of incorrect fuel or engine oil that renders the emissions... manufacturers of new engines, manufacturers of equipment containing these engines, and manufacturers of new...

40 CFR 1068.101 - What general actions does this regulation prohibit?

Code of Federal Regulations, 2013 CFR

2013-07-01

..., operating an engine without a supply of appropriate quality urea if the emissions control system relies on urea to reduce NOx emissions or the use of incorrect fuel or engine oil that renders the emissions... manufacturers of new engines, manufacturers of equipment containing these engines, and manufacturers of new...

Emission rates of regulated pollutants from current technology heavy-duty diesel and natural gas goods movement vehicles.

PubMed

Thiruvengadam, Arvind; Besch, Marc C; Thiruvengadam, Pragalath; Pradhan, Saroj; Carder, Daniel; Kappanna, Hemanth; Gautam, Mridul; Oshinuga, Adewale; Hogo, Henry; Miyasato, Matt

2015-04-21

Chassis dynamometer emissions testing of 11 heavy-duty goods movement vehicles, including diesel, natural gas, and dual-fuel technology, compliant with US-EPA 2010 emissions standard were conducted. Results of the study show that three-way catalyst (TWC) equipped stoichiometric natural gas vehicles emit 96% lower NOx emissions as compared to selective catalytic reduction (SCR) equipped diesel vehicles. Characteristics of drayage truck vocation, represented by the near-dock and local drayage driving cycles, were linked to high NOx emissions from diesel vehicles equipped with a SCR. Exhaust gas temperatures below 250 °C, for more than 95% duration of the local and near-dock driving cycles, resulted in minimal SCR activity. The low percentage of activity SCR over the local and near-dock cycles contributed to a brake-specific NOx emissions that were 5-7 times higher than in-use certification limit. The study also illustrated the differences between emissions rate measured from chassis dynamometer testing and prediction from the EMFAC model. The results of the study emphasize the need for model inputs relative to SCR performance as a function of driving cycle and engine operation characteristics.

High NO2/NOx emissions downstream of the catalytic diesel particulate filter: An influencing factor study.

PubMed

He, Chao; Li, Jiaqiang; Ma, Zhilei; Tan, Jianwei; Zhao, Longqing

2015-09-01

Diesel vehicles are responsible for most of the traffic-related nitrogen oxide (NOx) emissions, including nitric oxide (NO) and nitrogen dioxide (NO2). The use of after-treatment devices increases the risk of high NO2/NOx emissions from diesel engines. In order to investigate the factors influencing NO2/NOx emissions, an emission experiment was carried out on a high pressure common-rail, turbocharged diesel engine with a catalytic diesel particulate filter (CDPF). NO2 was measured by a non-dispersive ultraviolet analyzer with raw exhaust sampling. The experimental results show that the NO2/NOx ratios downstream of the CDPF range around 20%-83%, which are significantly higher than those upstream of the CDPF. The exhaust temperature is a decisive factor influencing the NO2/NOx emissions. The maximum NO2/NOx emission appears at the exhaust temperature of 350°C. The space velocity, engine-out PM/NOx ratio (mass based) and CO conversion ratio are secondary factors. At a constant exhaust temperature, the NO2/NOx emissions decreased with increasing space velocity and engine-out PM/NOx ratio. When the CO conversion ratios range from 80% to 90%, the NO2/NOx emissions remain at a high level. Copyright © 2015. Published by Elsevier B.V.

DOE Light Truck Clean Diesel (LTCD) Program Final Caterpillar Public Report Light Truck Clean Diesel Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eric Fluga

The US Department of Energy and Caterpillar entered a Cooperative Agreement to develop compression ignition engine technology suitable for the light truck/SUV market. Caterpillar, in collaboration with a suitable commercialization partner, developed a new Compression Ignition Direct Injection (CIDI) engine technology to dramatically improve the emissions and performance of light truck engines. The overall program objective was to demonstrate engine prototypes by 2004, with an order of magnitude emission reduction while meeting challenging fuel consumption goals. Program emphasis was placed on developing and incorporating cutting edge technologies that could remove the current impediments to commercialization of CIDI power sources inmore » light truck applications. The major obstacle to commercialization is emissions regulations with secondary concerns of driveability and NVH (noise, vibration and harshness). The target emissions levels were 0.05 g/mile NOx and 0.01 g/mile PM to be compliant with the EPA Tier 2 fleet average requirements of 0.07 g/mile and the CARB LEV 2 of 0.05 g/mile for NOx, both have a PM requirement of 0.01 g/mile. The program team developed a combustion process that fundamentally shifted the classic NOx vs. PM behavior of CIDI engines. The NOx vs. PM shift was accomplished with a form of Homogeneous Charge Compression Ignition (HCCI). The HCCI concept centers on appropriate mixing of air and fuel in the compression process and controlling the inception and rate of combustion through various means such as variable valve timing, inlet charge temperature and pressure control. Caterpillar has adapted an existing Caterpillar design of a single injector that: (1) creates the appropriate fuel and air mixture for HCCI, (2) is capable of a more conventional injection to overcome the low power density problems of current HCCI implementations, (3) provides a mixed mode where both the HCCI and conventional combustion are functioning in the same combustion cycle. Figure 1 illustrates the mixed mode injection system. Under the LTCD program Caterpillar developed a mixed mode injector for a multi-cylinder engine system. The mixed mode injection system represents a critical enabling technology for the implementation of HCCI. In addition, Caterpillar implemented variable valve system technology and air system technology on the multi-cylinder engine platform. The valve and air system technology were critical to system control. Caterpillar developed the combustion system to achieve a 93% reduction in NOx emissions. The resulting NOx emissions were 0.12 gm/mile NOx. The demonstrated emissions level meets the stringent Tier 2 Bin 8 requirement without NOx aftertreatment! However, combustion development alone was not adequate to meet the program goal of 0.05gm/mile NOx. To meet the program goals, an additional 60% NOx reduction technology will be required. Caterpillar evaluated a number of NOx reduction technologies to quantify and understand the NOx reduction potential and system performance implications. The NOx adsorber was the most attractive NOx aftertreatment option based on fuel consumption and NOx reduction potential. In spite of the breakthrough technology development conducted under the LTCD program there remains many significant challenges associated with the technology configuration. For HCCI, additional effort is needed to develop a robust control strategy, reduce the hydrocarbon emissions at light load condition, and develop a more production viable fuel system. Furthermore, the NOx adsorber suffers from cost, packaging, and durability challenges that must be addressed.« less

CONTROLLING NOX EMISSION FROM INDUSTRIAL SOURCES

EPA Science Inventory

A number of regulatory actions focused on reducing NO_x emissions from stationary combustion sources have been taken in the United States in the last decade. These actions include the Acid Rain NO_x regulations, the Ozone Transport Commission's NO_x ...

Impact of biodiesel and renewable diesel on emissions of regulated pollutants and greenhouse gases on a 2000 heavy duty diesel truck

NASA Astrophysics Data System (ADS)

Na, Kwangsam; Biswas, Subhasis; Robertson, William; Sahay, Keshav; Okamoto, Robert; Mitchell, Alexander; Lemieux, Sharon

2015-04-01

As part of a broad evaluation of the environmental impacts of biodiesel and renewable diesel as alternative motor fuels and fuel blends in California, the California Air Resources Board's (CARB) Heavy-duty Diesel Emission Testing Laboratory conducted chassis dynamometer exhaust emission measurements on in-use heavy-heavy-duty diesel trucks (HHDDT). The results presented here detail the impact of biodiesel and renewable diesel fuels and fuel blends as compared to CARB ULSD on particulate matter (PM), regulated gases, and two greenhouse gases emissions from a HHDDT with a 2000 C15 Caterpillar engine with no exhaust after treatment devices. This vehicle was tested over the Urban Dynamometer Driving Schedule (UDDS) and the cruise portion of the California HHDDT driving schedule. Three neat blend stocks (soy-based and animal-based fatty acid methyl ester (FAME) biodiesels, and a renewable diesel) and CARB-certified ultra-low sulfur diesel (CARB ULSD) along with their 20% and 50% blends (blended with CARB ULSD) were tested. The effects of blend level on emission characteristics were discussed on g·km-1 basis. The results showed that PM, total hydrocarbon (THC), and carbon monoxide (CO) emissions were dependent on driving cycles, showing higher emissions for the UDDS cycles with medium load than the highway cruise cycle with high load on per km basis. When comparing CARB ULSD to biodiesels and renewable diesel blends, it was observed that the PM, THC, and CO emissions decreased with increasing blend levels regardless of the driving cycles. Note that biodiesel blends showed higher degree of emission reductions for PM, THC, and CO than renewable diesel blends. Both biodiesels and renewable diesel blends effectively reduced PM emissions, mainly due to reduction in elemental carbon emissions (EC), however no readily apparent reductions in organic carbon (OC) emissions were observed. When compared to CARB ULSD, soy- and animal-based biodiesel blends showed statistically significant increases in nitrogen oxides (NOx) emissions for 50% or higher biodiesel blends. The 20% blends of the biodiesels showed no statistically significant effect on NOx emissions on any cycle. In contrast, renewable diesel slightly decreased NOx emissions and the degree of reduction was statistically significant for 50% or higher blends over the UDDS cycle, but not at the 20% blends. The highway cruise cycles did not show a statistically strong NOx emission trend with increasing blend level of renewable diesel. Biodiesel and renewable fuel impacts on two greenhouse gases, CO2 and N2O emissions were of lower magnitude when compared to other regulated pollutants emissions, showing a change in their emissions within approximately ±3% from the CARB ULSD.

40 CFR 75.72 - Determination of NOX mass emissions for common stack and multiple stack configurations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 16 2011-07-01 2011-07-01 false Determination of NOX mass emissions... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTINUOUS EMISSION MONITORING NOX Mass Emissions Provisions § 75.72 Determination of NOX mass emissions for common stack and multiple stack...

Impact of cold temperature on Euro 6 passenger car emissions.

PubMed

Suarez-Bertoa, Ricardo; Astorga, Covadonga

2018-03-01

Hydrocarbons, CO, NOx, NH 3 , N 2 O, CO 2 and particulate matter emissions affect air quality, global warming and human health. Transport sector is an important source of these pollutants and high pollution episodes are often experienced during the cold season. However, EU vehicle emissions regulation at cold ambient temperature only addresses hydrocarbons and CO vehicular emissions. For that reason, we have studied the impact that cold ambient temperatures have on Euro 6 diesel and spark ignition (including: gasoline, ethanol flex-fuel and hybrid vehicles) vehicle emissions using the World-harmonized Light-duty Test Cycle (WLTC) at -7 °C and 23 °C. Results indicate that when facing the WLTC at 23 °C the tested vehicles present emissions below the values set for type approval of Euro 6 vehicles (still using NEDC), with the exception of NOx emissions from diesel vehicles that were 2.3-6 times higher than Euro 6 standards. However, emissions disproportionally increased when vehicles were tested at cold ambient temperature (-7 °C). High solid particle number (SPN) emissions (>1 × 10 11 # km -1 ) were measured from gasoline direct injection (GDI) vehicles and gasoline port fuel injection vehicles. However, only diesel and GDI SPN emissions are currently regulated. Results show the need for a new, technology independent, procedure that enables the authorities to assess pollutant emissions from vehicles at cold ambient temperatures. Harmful pollutant emissions from spark ignition and diesel vehicles are strongly and negatively affected by cold ambient temperatures. Only hydrocarbon, CO emissions are currently regulated at cold temperature. Therefore, it is of great importance to revise current EU winter vehicle emissions regulation. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Criteria pollutant and greenhouse gas emissions from CNG transit buses equipped with three-way catalysts compared to lean-burn engines and oxidation catalyst technologies.

PubMed

Yoon, Seungju; Collins, John; Thiruvengadam, Arvind; Gautam, Mridul; Herner, Jorn; Ayala, Alberto

2013-08-01

Engine and exhaust control technologies applied to compressed natural gas (CNG) transit buses have advanced from lean-burn, to lean-burn with oxidation catalyst (OxC), to stoichiometric combustion with three-way catalyst (TWC). With this technology advancement, regulated gaseous and particulate matter emissions have been significantly reduced. Two CNG transit buses equipped with stoichiometric combustion engines and TWCs were tested on a chassis dynamometer, and their emissions were measured. Emissions from the stoichiometric engines with TWCs were then compared to the emissions from lean-burn CNG transit buses tested in previous studies. Stoichiometric combustion with TWC was effective in reducing emissions of oxides of nitrogen (NO(x)), particulate matter (PM), and nonmethane hydrocarbon (NMHC) by 87% to 98% depending on pollutants and test cycles, compared to lean combustion. The high removal efficiencies exceeded the emission reduction required from the certification standards, especially for NO(x) and PM. While the certification standards require 95% and 90% reductions for NO(x) and PM, respectively, from the engine model years 1998-2003 to the engine model year 2007, the measured NO(x) and PM emissions show 96% and 95% reductions, respectively, from the lean-burn engines to the stoichiometric engines with TWC over the transient Urban Dynamometer Driving Schedule (UDDS) cycle. One drawback of stoichiometric combustion with TWC is that this technology produces higher carbon monoxide (CO) emissions than lean combustion. In regard to controlling CO emissions, lean combustion with OxC is more effective than stoichiometric combustion. Stoichiometric combustion with TWC produced higher greenhouse gas (GHG) emissions including carbon dioxide (CO2) and methane (CH4) than lean combustion during the UDDS cycle, but lower GHG emissions during the steady-state cruise cycle. Stoichiometric combustion with three-way catalyst is currently the best emission control technology available for compressed natural gas (CNG) transit buses to meet the stringent U.S. Environmental Protection Agency (EPA) 2010 heavy-duty engine NO(x) emissions standard. For existing lean-burn CNG transit buses in the fleet, oxidation catalyst would be the most effective retrofit technology for the control of NMHC and CO emissions.

Understanding NOx emission trends in China based on OMI observations

NASA Astrophysics Data System (ADS)

Wang, Y.; Ga, D.; Smeltzer, C. D.; Yi, R.; Liu, Z.

2012-12-01

We analyze OMI observations of NO2 columns over China from 2005 to 2010. Simulations using a regional 3-D chemical transport model (REAM) are used to derive the top-down anthropogenic NOx emissions. The Kendall method is then applied to derive the emission trend. The emission trend is affected by the economic slowdown in 2009. After removing the effect of one year abnormal data, the overall emission trend is 4.35±1.42% per year, which is slower than the linear-regression trend of 5.8-10.8% per year reported for previous years. We find large regional, seasonal, and urban-rural variations in emission trend. The annual emission trends of Northeast China, Central China Plain, Yangtze River Delta and Pearl River Delta are 44.98±1.39%, 5.24±1.63%, 3.31±1.02% and -4.02±1.87%, respectively. The annual emission trends of four megacities, Beijing, Shanghai, Guangzhou and Shenzhen are 0.7±0.27%, -0.75±0.31%, -4.08±1.21% and -6.22±2.85%,, considerably lower than the regional averages. These results appear to suggest that a number of factors, including migration of high-emission industries, vehicle emission regulations, emission control measures of thermal power plants, increased hydro-power usage, have reduced or reversed the increasing trend of NOx emissions in more economically developed megacities and southern coastal regions.

40 CFR 80.50 - General test procedure requirements for augmentation of the emission models.

Code of Federal Regulations, 2014 CFR

2014-07-01

... § 80.45. (1) VOC, NOX, CO, and CO2 emissions must be measured for all fuel-vehicle combinations tested. (2) Toxics emissions must be measured when testing the extension fuels per the requirements of § 80... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Reformulated...

40 CFR 80.50 - General test procedure requirements for augmentation of the emission models.

Code of Federal Regulations, 2010 CFR

2010-07-01

... § 80.45. (1) VOC, NOX, CO, and CO2 emissions must be measured for all fuel-vehicle combinations tested. (2) Toxics emissions must be measured when testing the extension fuels per the requirements of § 80... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Reformulated...

40 CFR 80.50 - General test procedure requirements for augmentation of the emission models.

Code of Federal Regulations, 2012 CFR

2012-07-01

... § 80.45. (1) VOC, NOX, CO, and CO2 emissions must be measured for all fuel-vehicle combinations tested. (2) Toxics emissions must be measured when testing the extension fuels per the requirements of § 80... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Reformulated...

40 CFR 80.50 - General test procedure requirements for augmentation of the emission models.

Code of Federal Regulations, 2011 CFR

2011-07-01

... § 80.45. (1) VOC, NOX, CO, and CO2 emissions must be measured for all fuel-vehicle combinations tested. (2) Toxics emissions must be measured when testing the extension fuels per the requirements of § 80... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Reformulated...

40 CFR 86.164-08 - Supplemental Federal Test Procedure calculations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... provisions provide the procedures for calculating mass emission results of each regulated exhaust pollutant... this section. These provisions provide the procedures for determining the weighted mass emissions for... reported test results for the SFTP composite (NMHC+NOX) and optional composite CO standards shall be...

40 CFR 86.164-08 - Supplemental Federal Test Procedure calculations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... provisions provide the procedures for calculating mass emission results of each regulated exhaust pollutant... this section. These provisions provide the procedures for determining the weighted mass emissions for... reported test results for the SFTP composite (NMHC+NOX) and optional composite CO standards shall be...

NOx emissions in China: historical trends and future perspectives

NASA Astrophysics Data System (ADS)

Zhao, B.; Wang, S. X.; Liu, H.; Xu, J. Y.; Fu, K.; Klimont, Z.; Hao, J. M.; He, K. B.; Cofala, J.; Amann, M.

2013-10-01

Nitrogen oxides (NOx) are key pollutants for the improvement of ambient air quality. Within this study we estimated the historical NOx emissions in China for the period 1995-2010, and calculated future NOx emissions every five years until 2030 under six emission scenarios. Driven by the fast growth of energy consumption, we estimate the NOx emissions in China increased rapidly from 11.0 Mt in 1995 to 26.1 Mt in 2010. Power plants, industry and transportation were major sources of NOx emissions, accounting for 28.4%, 34.0%, and 25.4% of the total NOx emissions in 2010, respectively. Two energy scenarios, a business as usual scenario (BAU) and an alternative policy scenario (PC), were developed to project future energy consumption. In 2030, total energy consumption is projected to increase by 64% and 27% from 2010 level respectively. Three sets of end-of-pipe pollution control measures, including baseline, progressive, and stringent control case, were developed for each energy scenario, thereby constituting six emission scenarios. By 2030, the total NOx emissions are projected to increase (compared to 2010) by 36% in the baseline while policy cases result in reduction up to 61% in the most ambitious case with stringent control measures. More than a third of the reduction achieved by 2030 between least and most ambitious scenario comes from power sector, and more than half is distributed equally between industry and transportation sectors. Selective catalytic reduction dominates the NOx emission reductions in power plants, while life style changes, control measures for industrial boilers and cement production are major contributors to reductions in industry. Timely enforcement of legislation on heavy-duty vehicles would contribute significantly to NOx emission reductions. About 30% of the NOx emission reduction in 2020 and 40% of the NOx emission reduction in 2030 could be treated as the ancillary benefit of energy conservation. Sensitivity analysis was conducted to explore the impact of key factors on future emissions.

The challenge to NOx emission control for heavy-duty diesel vehicles in China

NASA Astrophysics Data System (ADS)

Wu, Y.; Zhang, S. J.; Li, M. L.; Ge, Y. S.; Shu, J. W.; Zhou, Y.; Xu, Y. Y.; Hu, J. N.; Liu, H.; Fu, L. X.; He, K. B.; Hao, J. M.

2012-10-01

China's new "Twelfth Five-Year Plan" set a target for total NOx emission reduction of 10% for the period of 2011-2015. Heavy-duty diesel vehicles (HDDVs) have been considered a major contributor to NOx emissions in China. Beijing initiated a comprehensive vehicle test program in 2008. This program included a sub-task for measuring on-road emission profiles of hundreds of HDDVs using portable emission measurement systems (PEMS). The major finding is that neither the on-road distance-specific (g km-1) nor brake-specific (g kWh-1) NOx emission factors for diesel buses and heavy-duty diesel trucks improved in most cases as emission standards became more stringent. For example, the average NOx emission factors for Euro II, Euro III and Euro IV buses are 11.3 ± 3.3 g km-1, 12.5 ± 1.3 g km-1, and 11.8 ± 2.0 g km-1, respectively. No statistically significant difference in NOx emission factors was observed between Euro II and III buses. Even for Euro IV buses equipped with SCR systems, the NOx emission factors are similar to Euro III buses. The data regarding real-time engine performance of Euro IV buses suggest the engine certification cycles did not reflect their real-world operating conditions. These new on-road test results indicate that previous estimates of total NOx emissions for HDDV fleet may be significantly underestimated. The new estimate in total NOx emissions for the Beijing HDDV fleet in 2009 is 37.0 Gg, an increase of 45% compared to the previous study. Further, we estimate that the total NOx emissions for the national HDDV fleet in 2009 are approximately 4.0 Tg, higher by 1.0 Tg (equivalent to 18% of total NOx emissions for vehicle fleet in 2009) than that estimated in the official report. This would also result in 4% increase in estimation of national anthropogenic NOx emissions. More effective control measures (such as promotion of CNG buses and a new in-use compliance testing program) are urged to secure the goal of total NOx mitigation for the HDDV fleet in the future.

SCR SYSTEMS FOR HEAVY DUTY TRUCKS: PROGRESS TOWARDS MEETING EURO 4 EMISSION STANDARDS IN 2005

DOE Office of Scientific and Technical Information (OSTI.GOV)

Frank, W; Huethwohl, G; Maurer, B

2003-08-24

Emissions of diesel engines contain some components, which support the generation of smog and which are classified hazardous. Exhaust gas aftertreatment is a powerful tool to reduce the NOx and Particulate emissions. The NOx-emission can be reduced by the SCR technology. SCR stands for Selective Catalytic Reduction. A reduction agent has to be injected into the exhaust upstream of a catalyst. On the catalyst the NOx is reduced to N2 (Nitrogen) and H2O (Water). This catalytic process was developed in Japan about 30 years ago to reduce the NOx emission of coal-fired power plants. The first reduction agent used wasmore » anhydrous ammonia (NH3). SCR technology was used with diesel engines starting mid of the 80s. First applications were stationary operating generator-sets. In 1991 a joint development between DaimlerChrysler, MAN, IVECO and Siemens was started to use SCR technology for the reduction of heavy duty trucks. Several fleet tests demonstrated the durability of the systems. To day, SCR technology is the most promising technology to fulfill the new European Regulations EURO 4 and EURO 5 being effective Oct. 2005 and Oct. 2008. The efficient NOx reduction of the catalyst allows an engine calibration for low fuel consumption. DaimlerChrysler decided to use the SCR technology on every heavy duty truck and bus in Europe and many other truck manufacturers will introduce SCR technology to fulfill the 2005 emission regulation. The truck manufacturers in Europe agreed to use aqueous solution of Urea as reducing agent. The product is called AdBlue. AdBlue is a non toxic, non smelling liquid. The consumption is about 5% of the diesel fuel consumption to reduce the NOx emissions. A small AdBlue tank has to be installed to the vehicle. With an electronically controlled dosing system the AdBlue is injected into the exhaust. The dosing system is simple and durable. It has proven its durability during winter and summer testing as well as in fleet tests. The infrastructure for AdBlue is under evaluation in Europe by Urea Producers and Mineral Oil companies to be readily available in time. Urea is one of the most common chemical products in the world and the production and the distribution very much experienced. However, a pure grade is needed for automotive application and requires special attention.« less

Environmental implications on the oxygenation of gasoline with ethanol in the metropolitan area of Mexico City.

PubMed

Schifter, I; Vera, M; Díaz, L; Guzmán, E; Ramos, F; López-Salinas, E

2001-05-15

Motor vehicle emission tests were performed on 12 in-use light duty vehicles, made up of the most representative emission control technologies in Mexico City: no catalyst, oxidative catalyst, and three way catalyst. Exhaust regulated (CO, NOx, and hydrocarbons) and toxic (benzene, formaldehyde, acetaldehyde, and 1,3-butadiene) emissions were evaluated for MTBE (5 vol %)- and ethanol (3, 6, and 10 vol %)-gasoline blends. The most significant overall emissions variations derived from the use of 6 vol % ethanol (relative to a 5% MTBE base gasoline) were 16% decrease in CO, 28% reduction in formaldehyde, and 80% increase in acetaldehyde emissions. A 26% reduction in CO emissions from the oldest fleet (< MY 1991, without catalytic converter), which represents about 44% of the in-use light duty vehicles in Mexico city, can be attained when using 6 vol% ethanol-gasoline, without significant variation in hydrocarbons and NOx emissions, when compared with a 5% vol MTBE-gasoline. On the basis of the emissions results, an estimation of the change in the motor vehicle emissions of the metropolitan area of Mexico city was calculated for the year 2010 if ethanol were to be used instead of MTBE, and the outcome was a considerable decrease in all regulated and toxic emissions, despite the growing motor vehicle population.

40 CFR 75.71 - Specific provisions for monitoring NOX and heat input for the purpose of calculating NOX mass...

Code of Federal Regulations, 2010 CFR

2010-07-01

... and heat input for the purpose of calculating NOX mass emissions. 75.71 Section 75.71 Protection of... MONITORING NOX Mass Emissions Provisions § 75.71 Specific provisions for monitoring NOX and heat input for the purpose of calculating NOX mass emissions. (a) Coal-fired units. The owner or operator of a coal...

An assessment of cruise NOx emissions of short-haul commercial flights

NASA Astrophysics Data System (ADS)

Turgut, Enis T.; Usanmaz, Oznur

2017-12-01

Cruise NOx emissions of aircraft are an important input parameter for studies investigating climate change due to their ability to alter the concentrations of certain trace gases, such as ozone, methane, and hydroxyl in the atmosphere, and to induce positive radiative forcing. Therefore, it is of importance to minimize estimation errors on NOx emitted from aircraft engines at high altitude. In this study, the cruise NOx emissions of a frequently-used narrow-bodied aircraft type operating domestic flights in Turkey, are quantified based on numerous actual flight, actual emissions and actual meteorological data. The overall average cruise NOx emissions index is found to be ∼10 g/kg fuel. In addition, newly-developed parameters of the aircraft cruise NOx footprint and NOx intensity are calculated to be 0.5 g/pa-NM and ∼60 g/NM, respectively. Regarding the effects of flight parameters on cruise NOx emissions, while there is a distinct increase in NOx parameters with an increase in aircraft mass, this may differ for altitude. The results reveal that the NOx emissions index tends to increase slightly by 1-2%, particularly above 28,000 ft, whereas NOx intensity decreases at a rate of 2.4-2.7% per 2000 ft of cruise altitude increase.

Estimating nitrogen oxides emissions at city scale in China with a nightlight remote sensing model.

PubMed

Jiang, Jianhui; Zhang, Jianying; Zhang, Yangwei; Zhang, Chunlong; Tian, Guangming

2016-02-15

Increasing nitrogen oxides (NOx) emissions over the fast developing regions have been of great concern due to their critical associations with the aggravated haze and climate change. However, little geographically specific data exists for estimating spatio-temporal trends of NOx emissions. In order to quantify the spatial and temporal variations of NOx emissions, a spatially explicit approach based on the continuous satellite observations of artificial nighttime stable lights (NSLs) from the Defense Meteorological Satellite Program/Operational Linescan System (DMSP/OLS) was developed to estimate NOx emissions from the largest emission source of fossil fuel combustion. The NSL based model was established with three types of data including satellite data of nighttime stable lights, geographical data of administrative boundaries, and provincial energy consumptions in China, where a significant growth of NOx emission has experienced during three policy stages corresponding to the 9th-11th)Five-Year Plan (FYP, 1995-2010). The estimated national NOx emissions increased by 8.2% per year during the study period, and the total annual NOx emissions in China estimated by the NSL-based model were approximately 4.1%-13.8% higher than the previous estimates. The spatio-temporal variations of NOx emissions at city scale were then evaluated by the Moran's I indices. The global Moran's I indices for measuring spatial agglomerations of China's NOx emission increased by 50.7% during 1995-2010. Although the inland cities have shown larger contribution to the emission growth than the more developed coastal cities since 2005, the High-High clusters of NOx emission located in Beijing-Tianjin-Hebei regions, the Yangtze River Delta, and the Pearl River Delta should still be the major focus of NOx mitigation. Our results indicate that the readily available DMSP/OLS nighttime stable lights based model could be an easily accessible and effective tool for achieving strategic decision making toward NOx reduction. Copyright © 2015 Elsevier B.V. All rights reserved.

Emissions Benefits From Renewable Fuels and Other Alternatives for Heavy-Duty Vehicles

NASA Astrophysics Data System (ADS)

Hajbabaei, Maryam

There is a global effort to expand the use of alternative fuels due to their several benefits such as improving air quality with reducing some criteria emissions, reducing dependency on fossil fuels, and reducing greenhouse gases such as carbon dioxide. This dissertation is focused on investigating the impact of two popular alternative fuels, biodiesel and natural gas (NG), on emissions from heavy-duty engines. Biodiesel is one of the most popular renewable fuels with diesel applications. Although biodiesel blends are reported to reduce particulate matter, carbon monoxide, and total hydrocarbon emissions; there is uncertainty on their impact on nitrogen oxides (NOx) emissions. This dissertation evaluated the effect of biodiesel feedstock, biodiesel blend level, engine technology, and driving conditions on NOx emissions. The results showed that NOx emissions increase with 20% and higher biodiesel blends. Also, in this study some strategies were proposed and some fuel formulations were found for mitigating NOx emissions increases with biodiesel. The impact of 5% biodiesel on criteria emissions specifically NOx was also fully studied in this thesis. As a part of the results of this study, 5% animal-based biodiesel was certified for use in California based on California Air Resources Board emissions equivalent procedure. NG is one of the most prominent alternative fuels with larger reserves compared to crude oil. However, the quality of NG depends on both its source and the degree to which it is processed. The current study explored the impact of various NG fuels, ranging from low methane/high energy gases to high methane/low energy gases, on criteria and toxic emissions from NG engines with different combustion and aftertreatment technologies. The results showed stronger fuel effects for the lean-burn technology bus. Finally, this thesis investigated the impact of changing diesel fuel composition on the criteria emissions from a variety of heavy-duty engine technologies. Emissions from an average diesel fuel used throughout the U.S. were compared with a 10% aromatic, ultra-low sulfur diesel fuel used in California with more stringent air quality regulations. The results showed that the emerging aftertreatment technologies eventually eliminate the benefits of the lower aromatic content/higher cetane number diesel fuels.

Examining the Impact of Regional-Scale Air Quality Regulations on Human Health Outcomes

EPA Science Inventory

The NOx State Implementation Plan Call was issued by the U.S. Environmental Protection Agency to reduce the emissions of nitrogen oxides from the electric power sector to curtail the regional transport of the secondarily-formed pollutant, ozone. As emission control actions often...

Eastern Regional Technical Advisory Committee (ERTAC) Electricity Generating Unit (EGU) Emission Projection Tool (2015 EIC)

EPA Pesticide Factsheets

Class content will include examples of how the Tool maybe applied to calculate the impacts of various air pollution control regulations (for example, the Mercury and Air Toxics Rule) on future year activity as well as NOx, SO2, and CO2 emissions.

40 CFR 86.164-00 - Supplemental Federal Test Procedure calculations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... provide the procedures for calculating mass emission results of each regulated exhaust pollutant for the... section. These provisions provide the procedures for determining the weighted mass emissions for the FTP... test results for the SFTP composite (NMHC+NOX) and optional composite CO standards shall be computed by...

40 CFR 86.164-00 - Supplemental Federal Test Procedure calculations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... provide the procedures for calculating mass emission results of each regulated exhaust pollutant for the... section. These provisions provide the procedures for determining the weighted mass emissions for the FTP... test results for the SFTP composite (NMHC+NOX) and optional composite CO standards shall be computed by...

40 CFR 97.374 - Recordkeeping and reporting.

Code of Federal Regulations, 2010 CFR

2010-07-01

... section, the NOX emission rate and NOX concentration values substituted for missing data under subpart D... report the NOX mass emissions data and heat input data for such unit, in an electronic quarterly report... emissions) for such unit for the entire year and report the NOX mass emissions data and heat input data for...

40 CFR 97.374 - Recordkeeping and reporting.

Code of Federal Regulations, 2012 CFR

2012-07-01

...: (1) If the CAIR NOX Ozone Season unit is subject to an Acid Rain emissions limitation or a CAIR NOX... Acid Rain emissions limitation or a CAIR NOX emissions limitation, then the CAIR designated...) of this chapter. (4) For CAIR NOX Ozone Season units that are also subject to an Acid Rain emissions...

40 CFR 97.374 - Recordkeeping and reporting.

Code of Federal Regulations, 2014 CFR

2014-07-01

...: (1) If the CAIR NOX Ozone Season unit is subject to an Acid Rain emissions limitation or a CAIR NOX... Acid Rain emissions limitation or a CAIR NOX emissions limitation, then the CAIR designated...) of this chapter. (4) For CAIR NOX Ozone Season units that are also subject to an Acid Rain emissions...

40 CFR 97.374 - Recordkeeping and reporting.

Code of Federal Regulations, 2013 CFR

2013-07-01

...: (1) If the CAIR NOX Ozone Season unit is subject to an Acid Rain emissions limitation or a CAIR NOX... Acid Rain emissions limitation or a CAIR NOX emissions limitation, then the CAIR designated...) of this chapter. (4) For CAIR NOX Ozone Season units that are also subject to an Acid Rain emissions...

40 CFR 97.374 - Recordkeeping and reporting.

Code of Federal Regulations, 2011 CFR

2011-07-01

...: (1) If the CAIR NOX Ozone Season unit is subject to an Acid Rain emissions limitation or a CAIR NOX... Acid Rain emissions limitation or a CAIR NOX emissions limitation, then the CAIR designated...) of this chapter. (4) For CAIR NOX Ozone Season units that are also subject to an Acid Rain emissions...

Variation of radiative forcings and global warming potentials from regional aviation NOx emissions

NASA Astrophysics Data System (ADS)

Skowron, Agnieszka; Lee, David S.; De León, Ruben R.

2015-03-01

The response to hemispherical and regional aircraft NOx emissions is explored by using two climate metrics: radiative forcing (RF) and Global Warming Potential (GWP). The global chemistry transport model, MOZART-3 CTM, is applied in this study for a series of incremental aircraft NOx emission integrations to different regions. It was found that the sensitivity of chemical responses per unit emission rate from regional aircraft NOx emissions varies with size of aircraft NOx emission rate and that climate metric values decrease with increasing aircraft NOx emission rates, except for Southeast Asia. Previous work has recognized that aircraft NOx GWPs may vary regionally. However, the way in which these regional GWPs are calculated are critical. Previous studies have added a fixed amount of NOx to different regions. This approach can heavily bias the results of a regional GWP because of the well-established sensitivity of O3 production to background NOx whereby the Ozone Production Efficiency (OPE) is greater at small background NOx. Thus, even a small addition of NOx in a clean-air area can produce a large O3 response. Using this 'fixed addition' method of 0.035 Tg(N) yr-1, results in the greatest effect observed for North Atlantic and Brazil, ∼10.0 mW m-2/Tg(N) yr-1. An alternative 'proportional approach' is also taken that preserves the subtle balance of local NOx-O3-CH4 systems with the existing emission patterns of aircraft and background NOx, whereby a proportional amount of aircraft NOx, 5% (N) yr-1, is added to each region in order to determine the response. This results in the greatest effect observed for North Pacific that with its net NOx RF of 23.7 mW m-2/Tg(N) yr-1 is in contrast with the 'fixed addition' method. For determining regional NOx GWPs, it is argued that the 'proportional' approach gives more representative results. However, a constraint of both approaches is that the regional GWP determined is dependent on the relative global emission pattern, so if that changes in the future, the regional NOx GWP will change.

Development and application of a mobile laboratory for measuring emissions from diesel engines. 1. Regulated gaseous emissions.

PubMed

Cocker, David R; Shah, Sandip D; Johnson, Kent; Miller, J Wayne; Norbeck, Joseph M

2004-04-01

Information about in-use emissions from diesel engines remains a critical issue for inventory development and policy design. Toward that end, we have developed and verified the first mobile laboratory that measures on-road or real-world emissions from engines at the quality level specified in the U.S. Congress Code of Federal Regulations. This unique mobile laboratory provides information on integrated and modal regulated gaseous emission rates and integrated emission rates for speciated volatile and semivolatile organic compounds and particulate matter during real-world operation. Total emissions are captured and collected from the HDD vehicle that is pulling the mobile laboratory. While primarily intended to accumulate data from HDD vehicles, it may also be used to measure emission rates from stationary diesel sources such as back-up generators. This paper describes the development of the mobile laboratory, its measurement capabilities, and the verification process and provides the first data on total capture gaseous on-road emission measurements following the California Air Resources Board (ARB) 4-mode driving cycle, the hot urban dynamometer driving schedule (UDDS), the modified 5-mode cycle, and a 53.2-mi highway chase experiment. NOx mass emission rates (g mi(-1)) for the ARB 4-mode driving cycle, the hot UDDS driving cycle, and the chase experimentwerefoundto exceed current emission factor estimates for the engine type tested by approximately 50%. It was determined that congested traffic flow as well as "off-Federal Test Procedure cycle" emissions can lead to significant increases in per mile NOx emission rates for HDD vehicles.

Nitrous oxide pollution from aircraft to increase by 2050

NASA Astrophysics Data System (ADS)

Bhattacharya, Atreyee

2012-09-01

The transportation industry is not only one of the biggest sources of air pollution and a significant player in greenhouse gas-induced global warming, but, as a new study shows, the industry could also be responsible for episodes of ozone (O3 ) pollution, particularly over the United States and northern Europe. Combustion of fuel in cars, shipping vessels, and low-flying aircraft produce nitrogen oxides (NOx), which not only decrease the lifetime of greenhouse gases such as methane but also react with other molecules in the atmosphere to form tropospheric O3, another, more lethal, air pollutant. Hauglustaine and Koff used a global three-dimensional chemistry-climate model to investigate how different components of the transportation industry—cars, ships, and low-flying aircraft—would contribute to NOx pollution over the next few decades under several projected emission scenarios. They found that as road transportation stagnates or even declines due to stricter regulations and congestion, NOx emissions from cars will decrease over time. However, aircraft will increase in number and could contribute between 25% and 48% of NOx emissions, which will be most severe over the United States and Europe—two regions with the highest growth rate in commercial aviation.

Comparison of NOx emissions from China III and China IV in-use diesel trucks based on on-road measurements

NASA Astrophysics Data System (ADS)

Yao, Zhiliang; Wu, Bobo; Wu, Yunong; Cao, Xinyue; Jiang, Xi

2015-12-01

To mitigate NOx and other emissions from diesel vehicles, China I, China II, China III and China IV emissions standards for new vehicles have been implemented nationwide. However, recent on-road measurements using a portable emission measurement system (PEMS) have revealed no significant reductions in the NOx emissions factors of diesel trucks due to the change from China II emissions standards to the more stringent China III standards. Thus, it is important to understand the effect of the China IV emissions standard on NOx emissions. In this study, nine China III and nine China IV diesel trucks of three sizes (light-duty diesel trucks (LDDTs), medium-duty diesel trucks (MDDTs) and heavy-duty diesel trucks (HDDTs)) were tested on real roads in Beijing using a PEMS. Compared to the tested China III diesel trucks, the China IV diesel trucks showed significant reductions of the average NOx emissions factors in terms of both distance travelled and fuel consumption. However, the driving conditions had an important impact on the reduction. Under non-highway driving (NHD), several of the tested China IV diesel trucks experienced no reduction or an increase in NOx emissions compared to their China III counterparts. The NOx emissions factors of the 18 tested diesel trucks under NHD were on average 1.5-times greater than those under highway driving (HD), and the effects on NOx emissions removal from China III to China IV diesel trucks were greater under HD than under NHD. In addition, no significant reduction of NOx based on fuel consumption for China IV diesel trucks was observed for MDDTs and HDDTs compared to the test results for similar China II vehicles reported in a previous study. To reduce NOx emissions in China, additional control measures of vehicular NOx emissions should be formulated.

The challenge to NOx emission control for heavy-duty diesel vehicles in China

NASA Astrophysics Data System (ADS)

Wu, Y.; Zhang, S. J.; Li, M. L.; Ge, Y. S.; Shu, J. W.; Zhou, Y.; Xu, Y. Y.; Hu, J. N.; Liu, H.; Fu, L. X.; He, K. B.; Hao, J. M.

2012-07-01

China's new "Twelfth Five-Year Plan" set a target for total NOx emission reduction of 10% for the period of 2011-2015. Heavy-duty diesel vehicles (HDDVs) have been considered a major contributor to NOx emissions in China. Beijing initiated a comprehensive vehicle test program in 2008. This program included a sub-task for measuring on-road emission profiles of hundreds of HDDVs using portable emission measurement systems (PEMS). The major finding is that neither the on-road distance-specific (g km -1) nor brake-specific (g kW h-1) NOx emission factors for diesel buses and heavy-duty diesel trucks improved in most cases as emission standards became more stringent. For example, the average NOx emission factors for Euro II, Euro III and Euro IV buses are 11.3±3.3 g km-1, 12.5± 1.3 g km-1, and 11.8±2.0 g km-1, respectively. No statistically significant difference in NOx emission factors was observed between Euro II and III buses. Even for Euro IV buses equipped with SCR systems, the NOx emission factors are similar to Euro III buses. The data regarding real-time engine performance of Euro IV buses suggest the engine certification cycles did not reflect their real-world operating conditions. These new on-road test results indicate that previous estimates of total NOx emissions for HDDV fleet may be significantly underestimated. The new estimate in total NOx emissions for the Beijing HDDV fleet in 2009 is 37.0 Gg, an increase of 45% compared to the previous study. Further, we estimate that the total NOx emissions for the national HDDV fleet in 2009 are approximately 4.0 Tg, higher by 1.0 Tg (equivalent to 18% of total NOx emissions for vehicle fleet in 2009) than that estimated in the official report. This would also result in 4% increase in estimation of national anthropogenic NOx emissions. More effective control measures (such as promotion of CNG buses and a new in-use compliance testing program) are urged to secure the goal of total NOxmitigation for the HDDV fleet in the future.

Parse, simulation, and prediction of NOx emission across the Midwestern United States

NASA Astrophysics Data System (ADS)

Fang, H.; Michalski, G. M.; Spak, S.

2017-12-01

Accurately constraining N emissions in space and time has been a challenge for atmospheric scientists. It has been suggested that 15N isotopes may be a way of tracking N emission sources across various spatial and temporal scales. However, the complexity of multiple N sources that can quickly change in intensity has made this a difficult problem. We have used a SMOKE emission model to parse NOx emission across the Midwestern United States for a one-year simulation. An isotope mass balance methods was used to assign 15N values to road, non-road, point, and area sources. The SMOKE emissions and isotope mass balance were then combined to predict the 15N of NOx emissions (Figure 1). This ^15N of NOx emissions model was then incorporated into CMAQ to assess the role of transport and chemistry would impact the 15N value of NOx due to mixing and removal processes. The predicted 15N value of NOx was compared to those in recent measurements of NOx and atmospheric nitrate.

40 CFR 75.72 - Determination of NOX mass emissions for common stack and multiple stack configurations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... the affected units as the difference between NOX mass emissions measured in the common stack and NOX... emissions using the maximum potential NOX emission rate, the maximum potential flow rate, and either the maximum potential CO2 concentration or the minimum potential O2 concentration (as applicable). The maximum...

Development and review of Euro 5 passenger car emission factors based on experimental results over various driving cycles.

PubMed

Fontaras, Georgios; Franco, Vicente; Dilara, Panagiota; Martini, Giorgio; Manfredi, Urbano

2014-01-15

The emissions of CO2 and regulated pollutants (NOx, HC, CO, PM) of thirteen Euro 5 compliant passenger cars (seven gasoline, six Diesel) were measured on a chassis dynamometer. The vehicles were driven repeatedly over the European type-approval driving cycle (NEDC) and the more dynamic WMTC and CADC driving cycles. Distance-specific emission factors were derived for each pollutant and sub-cycle, and these were subsequently compared to the corresponding emission factors provided by the reference European models used for vehicle emission inventory compilation (COPERT and HBEFA) and put in context with the applicable European emission limits. The measured emissions stayed below the legal emission limits when the type-approval cycle (NEDC) was used. Over the more dynamic cycles (considered more representative of real-world driving) the emissions were consistently higher but in most cases remained below the type-approval limit. The high NOx emissions of Diesel vehicles under real-world driving conditions remain the main cause for environmental concern regarding the emission profile of Euro 5 passenger cars. Measured emissions of NOx exceeded the type-approval limits (up to 5 times in extreme cases) and presented significantly increased average values (0.35 g/km for urban driving and 0.56 g/km for motorway driving). The comparison with the reference models showed good correlation in all cases, a positive finding considering the importance of these tools in emission monitoring and policy-making processes. © 2013. Published by Elsevier B.V. All rights reserved.

Overall evaluation of combustion and NO(x) emissions for a down-fired 600 MW(e) supercritical boiler with multiple injection and multiple staging.

PubMed

Kuang, Min; Li, Zhengqi; Liu, Chunlong; Zhu, Qunyi

2013-05-07

To achieve significant reductions in NOx emissions and to eliminate strongly asymmetric combustion found in down-fired boilers, a deep-air-staging combustion technology was trialed in a down-fired 600 MWe supercritical utility boiler. By performing industrial-sized measurements taken of gas temperatures and species concentrations in the near wing-wall region, carbon in fly ash and NOx emissions at various settings, effects of overfire air (OFA) and staged-air damper openings on combustion characteristics, and NOx emissions within the furnace were experimentally determined. With increasing the OFA damper opening, both fluctuations in NOx emissions and carbon in fly ash were initially slightly over OFA damper openings of 0-40% but then lengthened dramatically in openings of 40-70% (i.e., NOx emissions reduced sharply accompanied by an apparent increase in carbon in fly ash). Decreasing the staged-air declination angle clearly increased the combustible loss but slightly influenced NOx emissions. In comparison with OFA, the staged-air influence on combustion and NOx emissions was clearly weaker. Only at a high OFA damper opening of 50%, the staged-air effect was relatively clear, i.e., enlarging the staged-air damper opening decreased carbon in fly ash and slightly raised NOx emissions. By sharply opening the OFA damper to deepen the air-staging conditions, although NOx emissions could finally reduce to 503 mg/m(3) at 6% O2 (i.e., an ultralow NOx level for down-fired furnaces), carbon in fly ash jumped sharply to 15.10%. For economical and environment-friendly boiler operations, an optimal damper opening combination (i.e., 60%, 50%, and 50% for secondary air, staged-air, and OFA damper openings, respectively) was recommended for the furnace, at which carbon in fly ash and NOx emissions attained levels of about 10% and 850 mg/m(3) at 6% O2, respectively.

40 CFR 51.125 - Emissions reporting requirements for SIP revisions relating to budgets for SO2 and NOX emissions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... SIP revisions relating to budgets for SO2 and NOX emissions. 51.125 Section 51.125 Protection of... SIP revisions relating to budgets for SO2 and NOX emissions. (a) For its transport SIP revision under § 51.123 and/or 51.124, each State must submit to EPA SO2 and/or NOX emissions data as described in...

Verification of NOx emission inventories over North Korea.

PubMed

Kim, Na Kyung; Kim, Yong Pyo; Morino, Yu; Kurokawa, Jun-ichi; Ohara, Toshimasa

2014-12-01

In this study, the top-down NOx emissions estimated from satellite observations of NO2 vertical column densities over North Korea from 1996 to 2009 were analyzed. Also, a bottom-up NOx emission inventory from REAS 1.1 from 1980 to 2005 was analyzed with several statistics. REAS 1.1 was in good agreement with the top-down approach for both trend and amount. The characteristics of NOx emissions in North Korea were quite different from other developed countries including South Korea. In North Korea, emissions from industry sector was the highest followed by transportation sector in the 1980s. However, after 1990, the NOx emissions from other sector, mainly agriculture, became the 2nd highest. Also, no emission centers such as urban areas or industrial areas were distinctively observed. Finally, the monthly NOx emissions were high during the warm season. Copyright © 2014 Elsevier Ltd. All rights reserved.

A comprehensive inventory of the ship traffic exhaust emissions in the Baltic Sea from 2006 to 2009.

PubMed

Jalkanen, Jukka-Pekka; Johansson, Lasse; Kukkonen, Jaakko

2014-04-01

This study addresses the exhaust emissions of CO₂, NO(x), SO(x), CO, and PM(2.5) originated from Baltic Sea shipping in 2006-2009. Numerical results have been computed using the Ship Traffic Emissions Assessment Model. This model is based on the messages of the automatic identification system (AIS), which enable the positioning of ships with a high spatial resolution. The NO(x) emissions in 2009 were approximately 7 % higher than in 2006, despite the economic recession. However, the SO(x) emissions in 2009 were approximately 14 % lower, when compared to those in 2006, mainly caused by the fuel requirements of the SO(x) emission control area (SECA) which became effective in May 2006, but affected also by changes in ship activity. Results are presented on the differential geographic distribution of shipping emissions before (Jan-April 2006) and after (Jan-April 2009) the SECA regulations. The predicted NO(x) emissions in 2009 substantially exceeded the emissions in 2006 along major ship routes and at numerous harbors, mostly due to the continuous increase in the number of small vessels that use AIS transmitters. Although the SO(x) emissions have been reduced in 2009 in most major ship routes, these have increased in the vicinity of some harbors and on some densely trafficked routes. A seasonal variation of emissions is also presented, as well as the distribution of emissions in terms of vessel flag state, type, and weight.

Sensitivities of NOx transformation and the effects on surface ozone and nitrate

NASA Astrophysics Data System (ADS)

Lei, H.; Wang, J. X. L.

2014-02-01

As precursors to tropospheric ozone and nitrate, nitrogen oxide (NOx) in the present atmosphere and its transformation in response to emission and climate perturbations are studied by using the CAM-Chem model and air quality measurements from the National Emissions Inventory (NEI), Clean Air Status and Trends Network (CASTNET), and Environmental Protection Agency Air Quality System (EPA AQS). It is found that NOx transformations in present atmospheric conditions show different sensitivities over industrial and non-industrial regions. As a result, the surface ozone and nitrate formations can be divided into several regimes associated with the dominant emission types and relative levels of NOx and volatile organic compounds (VOC). Ozone production in industrial regions (the main NOx emission source areas) increases in warmer conditions and slightly decreases following an increase in NOx emissions due to NOx titration, which is opposite to the response in non-industrial regions. The ozone decrease following a temperature increase in non-industrial regions indicates that ozone production in regions that lack NOx emission sources may be sensitive to NOx transformation in remote source regions. The increase in NO2 from NOx titration over industrial regions results in an increase rate of total nitrate that remains higher than the increase rate of NOx emissions. The presented findings indicate that a change in the ozone concentration is more directly affected by changes in climate and precursor emissions, while a change in the nitrate concentration is affected by local ozone production types and their seasonal transfer. The sensitivity to temperature perturbations shows that a warmer climate accelerates the decomposition of odd nitrogen (NOy) during the night. As a result, the transformation rate of NOx to nitrate decreases. Examinations of the historical emissions and air quality records of a typical NOx-limited area, such as Atlanta and a VOC-limited area, such as Los Angeles further confirm the conclusions drawn from the modeling experiments.

Ozone Pollution

EPA Pesticide Factsheets

Known as tropospheric or ground-level ozone, this gas is harmful to human heath and the environment. Since it forms from emissions of volatile organic compounds (VOCs) and nitrogen oxides (NOx), these pollutants are regulated under air quality standards.

Environmental Assessment: Construction and Operation of New Security Forces Facility at Hill Air Force Base, Utah

DTIC Science & Technology

2008-10-01

Quality Standards NEPA National Environmental Policy Act of 1969 NOx Nitrogen Oxides OO-ALC Ogden Air Logistics Center OSHA Occupational Safety...current NAAQS. These standards regulate six common pollutants: carbon monoxide, lead, nitrogen oxides, sulfur oxides, ozone, and particulate matter...with the state plan. The conformity threshold emission level for ozone in maintenance areas is 100 tons per year for nitrogen oxide (NOx) and volatile

Estimation of vehicular emissions using dynamic emission factors: A case study of Delhi, India

NASA Astrophysics Data System (ADS)

Mishra, Dhirendra; Goyal, P.

2014-12-01

The estimation of vehicular emissions depends mainly on the values of emission factors, which are used for the development of a comprehensive emission inventory of vehicles. In this study the variations of emission factors as well as the emission rates have been studied in Delhi. The implementation of compressed natural gas (CNG), in the diesel and petrol, public vehicles in the year 2001 has changed the complete air quality scenario of Delhi. The dynamic emission factors of criteria pollutants viz. carbon monoxide (CO), nitrogen oxide (NOx) and particulate matter (PM10) for all types of vehicles have been developed after, which are based on the several factors such as regulated emission limits, number of vehicle deterioration, vehicle increment, vehicle age etc. These emission factors are found to be decreased continuously throughout the study years 2003-2012. The International Vehicle Emissions (IVE) model is used to estimate the emissions of criteria pollutants by utilizing a dataset available from field observations at different traffic intersections in Delhi. Thus the vehicular emissions, based on dynamic emission factors have been estimated for the years 2003-2012, which are found to be comparable with the monitored concentrations at different locations in Delhi. It is noticed that the total emissions of CO, NOx, and PM10 are increased by 45.63%, 68.88% and 17.92%, respectively up to the year 2012 and the emissions of NOx and PM10 are grown continuously with an annual average growth rate of 5.4% and 1.7% respectively.

40 CFR 76.10 - Alternative emission limitations.

Code of Federal Regulations, 2013 CFR

2013-07-01

...; and (ii) The installed NOX emission control system has been designed to meet the applicable emission... that the unit and NOX emission control system were operated in accordance with the bid and design specifications on which the design of the NOX emission control system was based; and (C) Unit operating data as...

40 CFR 76.10 - Alternative emission limitations.

Code of Federal Regulations, 2010 CFR

2010-07-01

...; and (ii) The installed NOX emission control system has been designed to meet the applicable emission... that the unit and NOX emission control system were operated in accordance with the bid and design specifications on which the design of the NOX emission control system was based; and (C) Unit operating data as...

Agriculture is a major source of NOx pollution in California

PubMed Central

Almaraz, Maya; Bai, Edith; Wang, Chao; Trousdell, Justin; Conley, Stephen; Faloona, Ian; Houlton, Benjamin Z.

2018-01-01

Nitrogen oxides (NOx = NO + NO2) are a primary component of air pollution—a leading cause of premature death in humans and biodiversity declines worldwide. Although regulatory policies in California have successfully limited transportation sources of NOx pollution, several of the United States’ worst–air quality districts remain in rural regions of the state. Site-based findings suggest that NOx emissions from California’s agricultural soils could contribute to air quality issues; however, a statewide estimate is hitherto lacking. We show that agricultural soils are a dominant source of NOx pollution in California, with especially high soil NOx emissions from the state’s Central Valley region. We base our conclusion on two independent approaches: (i) a bottom-up spatial model of soil NOx emissions and (ii) top-down airborne observations of atmospheric NOx concentrations over the San Joaquin Valley. These approaches point to a large, overlooked NOx source from cropland soil, which is estimated to increase the NOx budget by 20 to 51%. These estimates are consistent with previous studies of point-scale measurements of NOx emissions from the soil. Our results highlight opportunities to limit NOx emissions from agriculture by investing in management practices that will bring co-benefits to the economy, ecosystems, and human health in rural areas of California. PMID:29399630

40 CFR 87.64 - Sampling and analytical procedures for measuring gaseous exhaust emissions.

Code of Federal Regulations, 2012 CFR

2012-07-01

.../kilonewton rO. (c) Report CO2 by calculation from fuel mass flow rate measurements in Appendices 3 and 5 to... 1, 2011, report CO2 values along with your emission levels of regulated NOX to the Administrator for... on or after January 1, 2011. By January 1, 2011, report CO2 values along with your emission levels of...

Impact of passenger car NOx emissions and NO2 fractions on urban NO2 pollution - Scenario analysis for the city of Antwerp, Belgium

NASA Astrophysics Data System (ADS)

Degraeuwe, Bart; Thunis, Philippe; Clappier, Alain; Weiss, Martin; Lefebvre, Wouter; Janssen, Stijn; Vranckx, Stijn

2016-02-01

The annual NO2 concentrations in many European cities exceed the established air quality standard. This situation is mainly caused by Diesel cars whose NOx emissions are higher on the road than during type approval in the laboratory. Moreover, the fraction of NO2 in the NOx emissions of modern diesel cars appears to have increased as compared to previous models. In this paper, we assess 1) to which level the distance-specific NOx emissions of Diesel cars should be reduced to meet established air quality standards and 2) if it would be useful to introduce a complementary NO2 emissions limit. We develop a NO2 pollution model that accounts in an analysis of 9 emission scenarios for changes in both, the urban background NO2 concentrations and the local NO2 emissions at street level. We apply this model to the city of Antwerp, Belgium. The results suggest that a reduction in NOx emissions decreases the regional and urban NO2 background concentration; high NO2 fractions increase the ambient NO2 concentrations only in close spatial proximity to the emission source. In a busy access road to the city centre, the average NO2 concentration can be reduced by 23% if Diesel cars emitted 0.35 g NOx/km instead of the current 0.62 g NOx/km. Reductions of 45% are possible if the NOX emissions of Diesel cars decreased to the level of gasoline cars (0.03 g NOx/km). Our findings suggest that the Real-Driving Emissions (RDE) test procedure can solve the problem of NO2 exceedances in cities if it reduced the on-road NOx emissions of diesel cars to the permissible limit of 0.08 g/km. The implementation of a complementary NO2 emissions limit may then become superfluous. If Diesel cars continue to exceed by several factors their NOx emissions limit on the road, a shift of the vehicle fleet to gasoline cars may be necessary to solve persisting air quality problems.

Application of satellite observations for timely updates to global anthropogenic NOx emission inventories

NASA Astrophysics Data System (ADS)

Lamsal, L. N.; Martin, R. V.; Padmanabhan, A.; van Donkelaar, A.; Zhang, Q.; Sioris, C. E.; Chance, K.; Kurosu, T. P.; Newchurch, M. J.

2011-03-01

Anthropogenic emissions of nitrogen oxides (NOx) can change rapidly due to economic growth or control measures. Bottom-up emissions estimated using source-specific emission factors and activity statistics require years to compile and can become quickly outdated. We present a method to use satellite observations of tropospheric NO2 columns to estimate changes in NOx emissions. We use tropospheric NO2 columns retrieved from the SCIAMACHY satellite instrument for 2003-2009, the response of tropospheric NO2 columns to changes in NOx emissions determined from a global chemical transport model (GEOS-Chem), and the bottom-up anthropogenic NOx emissions for 2006 to hindcast and forecast the inventories. We evaluate our approach by comparing bottom-up and hindcast emissions for 2003. The two inventories agree within 6.0% globally and within 8.9% at the regional scale with consistent trends in western Europe, North America, and East Asia. We go on to forecast emissions for 2009. During 2006-2009, anthropogenic NOx emissions over land increase by 9.2% globally and by 18.8% from East Asia. North American emissions decrease by 5.7%.

NOx Emissions Performance and Correlation Equations for a Multipoint LDI Injector

NASA Technical Reports Server (NTRS)

He, Zhuohui J.; Chang, Clarence T.; Follen, Caitlin E.

2014-01-01

Lean Direct Injection (LDI) is a combustor concept that reduces nitrogen oxides (NOx) emissions. This paper looks at a 3-zone multipoint LDI concept developed by Parker Hannifin Corporation. The concept was tested in a flame-tube test facility at NASA Glenn Research Center. Due to test facility limitations, such as inlet air temperature and pressure, the flame-tube test was not able to cover the full set of engine operation conditions. Three NOx correlation equations were developed based on assessing NOx emissions dependencies on inlet air pressure (P3), inlet air temperature (T3), and fuel air equivalence ratio (phi) to estimate the NOx emissions at the unreachable high engine power conditions. As the results, the NOx emissions are found to be a strong function of combustion inlet air temperature and fuel air equivalence ratio but a weaker function of inlet air pressure. With these three equations, the NOx emissions performance of this injector concept is calculated as a 66 percent reduction relative to the ICAO CAEP-6 standard using a 55:1 pressure-ratio engine cycle. Uncertainty in the NOx emissions estimation increases as the extrapolation range departs from the experimental conditions. Since maximum inlet air pressure tested was less than 50 percent of the full power engine inlet air pressure, a future experiment at higher inlet air pressure conditions is needed to confirm the NOx emissions dependency on inlet air pressure.

NOx Emissions Performance and Correlation Equations for a Multipoint LDI Injector

NASA Technical Reports Server (NTRS)

He, Zhuohui Joe; Chang, Clarence T.; Follen, Caitlin E.

2015-01-01

Lean Direct Injection (LDI) is a combustor concept that reduces nitrogen oxides (NOx) emissions.This paper looks at a 3-zone multipoint LDI concept developed by Parker Hannifin Corporation. The concept was tested in a flame-tube test facility at NASA Glenn Research Center. Due to test facility limitations, such as inlet air temperature and pressure, the flame-tube test was not able to cover the full set of engine operation conditions. Three NOx correlation equations were developed based on assessing NOx emissions dependencies on inlet air pressure (P3), inlet air temperature (T3), and fuel air equivalence ratio(theta) to estimate the NOx emissions at the unreachable high engine power conditions. As the results, the NOx emissions are found to be a strong function of combustion inlet air temperature and fuel air equivalence ratio but a weaker function of inlet air pressure. With these three equations, the NOx emissions performance of this injector concept is calculated as a 66 reduction relative to the ICAO CAEP-6 standard using a 55:1 pressure-ratio engine cycle. Uncertainty in the NOx emissions estimation increases as the extrapolation range departs from the experimental conditions. Since maximum inlet air pressure tested was less than 50 of the full power engine inlet air pressure, a future experiment at higher inlet air pressure conditions is needed to confirm the NOx emissions dependency on inlet air pressure.

NOx Emissions Performance and Correlation Equations for a Multipoint LDI Injector

NASA Technical Reports Server (NTRS)

He, Zhuohui J.; Chang, Clarence T.; Follen, Caitlin E.

2015-01-01

Lean Direct Injection (LDI) is a combustor concept that reduces nitrogen oxides (NOx) emissions. This paper looks at a 3-zone multipoint LDI concept developed by Parker Hannifin Corporation. The concept was tested in a flame-tube test facility at NASA Glenn Research Center. Due to test facility limitations, such as inlet air temperature and pressure, the flame-tube test was not able to cover the full set of engine operation conditions. Three NOx correlation equations were developed based on assessing NOx emissions dependencies on inlet air pressure (P3), inlet air temperature (T3), and fuel air equivalence ratio (?) to estimate the NOx emissions at the unreachable high engine power conditions. As the results, the NOx emissions are found to be a strong function of combustion inlet air temperature and fuel air equivalence ratio but a weaker function of inlet air pressure. With these three equations, the NOx emissions performance of this injector concept is calculated as a 66% reduction relative to the ICAO CAEP-6 standard using a 55:1 pressure-ratio engine cycle. Uncertainty in the NOx emissions estimation increases as the extrapolation range departs from the experimental conditions. Since maximum inlet air pressure tested was less than 50% of the full power engine inlet air pressure, a future experiment at higher inlet air pressure conditions is needed to confirm the NOx emissions dependency on inlet air pressure.

NOx Emissions Performance and Correlation Equations for a Multipoint LDI Injector

NASA Technical Reports Server (NTRS)

He, Zhuohui J.; Chang, Clarence T.; Follen, Caitlin E.

2014-01-01

Lean Direct Injection (LDI) is a combustor concept that reduces nitrogen oxides (NOx) emissions. This paper looks at a 3-zone multipoint LDI concept developed by Parker Hannifin Corporation. The concept was tested in a flame-tube test facility at NASA Glenn Research Center. Due to test facility limitations, such as inlet air temperature and pressure, the flame-tube test was not able to cover the full set of engine operation conditions. Three NOx correlation equations were developed based on assessing NOx emissions dependencies on inlet air pressure (P3), inlet air temperature (T3), and fuel air equivalence ratio (?) to estimate the NOx emissions at the unreachable high engine power conditions. As the results, the NOx emissions are found to be a strong function of combustion inlet air temperature and fuel air equivalence ratio but a weaker function of inlet air pressure. With these three equations, the NOx emissions performance of this injector concept is calculated as a 66 percent reduction relative to the ICAO CAEP-6 standard using a 55:1 pressure-ratio engine cycle. Uncertainty in the NOx emissions estimation increases as the extrapolation range departs from the experimental conditions. Since maximum inlet air pressure tested was less than 50 percent of the full power engine inlet air pressure, a future experiment at higher inlet air pressure conditions is needed to confirm the NOx emissions dependency on inlet air pressure.

Worldwide biogenic soil NOx emission estimates from OMI NO2 observations and the GEOS-Chem model

NASA Astrophysics Data System (ADS)

Vinken, Geert; Boersma, Folkert; Maasakkers, Bram; Martin, Randall

2014-05-01

Bacteria in soils are an important source of biogenic nitrogen oxides (NOx = NO + NO2), which are important precursors for ozone (O3) formation. Furthermore NOx emissions contribute to increased nitrogen deposition and particulate matter formation. Bottom-up estimates of global soil NOx emissions range from 4 to 27 Tg N / yr, reflecting our incomplete knowledge of emission factors and processes driving these emissions. In this study we used, for the first time, OMI NO2 columns on all continents to reduce the uncertainty in soil NOx emissions. Regions and months dominated by soil NOx emissions were identified using a filtering scheme in the GEOS-Chem chemistry transport model. Consequently, we compared OMI observed NO2 observed columns to GEOS-Chem simulated columns and provide constraints for these months in 11 regions. This allows us to provide a top-down emission inventory for 2005 for soil NOx emissions from all continents. Our total global soil NOx emission inventory amounts to 10 Tg N / yr. Our estimate is 4% higher than the GEOS-Chem a priori (Hudman et al., 2012), but substantial regional differences exist (e.g. +20% for Sahel and India; and -40% for mid-USA). We furthermore observed a stronger seasonal cycle in the Sahel region, indicating directions for possible future improvements to the parameterization currently used in GEOS-Chem. We validated NO2 concentrations simulated with this new top-down inventory against surface NO2 measurements from monitoring stations in Africa, the USA and Europe. On the whole, we conclude that simulations with our new top-down inventory better agree with measurements. Our work shows that satellite retrieved NO2 columns can improve estimates of soil NOx emissions over sparsely monitored remote rural areas. We show that the range in previous estimates of soil NOx emissions is too large, and global emissions are most likely around 10 Tg N/yr, in agreement with the most recent parameterizations.

Using satellite data to guide emission control strategies for surface ozone pollution

NASA Astrophysics Data System (ADS)

Jin, X.; Fiore, A. M.

2017-12-01

Surface ozone (O3) has adverse effects on public health, agriculture and ecosystems. As a secondary pollutant, ozone is not emitted directly. Ozone forms from two classes of precursors: NOx and VOCs. We use satellite observations of formaldehyde (a marker of VOCs) and NO2 (a marker of NOx) to identify areas which would benefit more from reducing NOx emissions (NOx-limited) versus areas where reducing VOC emissions would lead to lower ozone (VOC-limited). We use a global chemical transport model (GEOS-Chem) to develop a set of threshold values that separate the NOx-limited and VOC-limited conditions. Combining these threshold values with a decadal record of satellite observations, we find that U.S. cities (e.g. New York, Chicago) have shifted from VOC-limited to NOx-limited ozone production regimes in the warm season. This transition reflects the NOx emission controls implemented over the past decade. Increasing NOx sensitivity implies that regional NOx emission control programs will improve O3 air quality more now than it would have a decade ago.

40 CFR 51.122 - Emissions reporting requirements for SIP revisions relating to budgets for NOX emissions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS REQUIREMENTS FOR PREPARATION, ADOPTION, AND SUBMITTAL... NOX emissions data as described in this section. (c) Each revision must provide for periodic reporting by the state of NOX emissions data to demonstrate whether the state's emissions are consistent with...

40 CFR 51.122 - Emissions reporting requirements for SIP revisions relating to budgets for NOX emissions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS REQUIREMENTS FOR PREPARATION, ADOPTION, AND SUBMITTAL... NOX emissions data as described in this section. (c) Each revision must provide for periodic reporting by the state of NOX emissions data to demonstrate whether the state's emissions are consistent with...

Effect of fuel-air-ratio nonuniformity on emissions of nitrogen oxides

NASA Technical Reports Server (NTRS)

Lyons, V. J.

1981-01-01

The inlet fuel-air ratio nonuniformity is studied to deterine how nitrogen oxide (NOx) emissions are affected. An increase in NOx emissions with increased fuel-air ratio nonuniformity for average equivalence ratios less than 0.7 and a decrease in NOx emissions for average equivalence ratios near stoichiometric is predicted. The degree of uniformityy of fuel-air ratio profiles that is necessary to achieve NOx emissions goals for actual engines that use lean, premixed, prevaporized combustion systems is determined.

Gas- and particle-phase primary emissions from in-use, on-road gasoline and diesel vehicles

NASA Astrophysics Data System (ADS)

May, Andrew A.; Nguyen, Ngoc T.; Presto, Albert A.; Gordon, Timothy D.; Lipsky, Eric M.; Karve, Mrunmayi; Gutierrez, Alváro; Robertson, William H.; Zhang, Mang; Brandow, Christopher; Chang, Oliver; Chen, Shiyan; Cicero-Fernandez, Pablo; Dinkins, Lyman; Fuentes, Mark; Huang, Shiou-Mei; Ling, Richard; Long, Jeff; Maddox, Christine; Massetti, John; McCauley, Eileen; Miguel, Antonio; Na, Kwangsam; Ong, Richard; Pang, Yanbo; Rieger, Paul; Sax, Todd; Truong, Tin; Vo, Thu; Chattopadhyay, Sulekha; Maldonado, Hector; Maricq, M. Matti; Robinson, Allen L.

2014-05-01

Tailpipe emissions from sixty-four unique light-duty gasoline vehicles (LDGVs) spanning model years 1987-2012, two medium-duty diesel vehicles and three heavy-duty diesel vehicles with varying levels of aftertreatment were characterized at the California Air Resources Board Haagen-Smit and Heavy-Duty Engine Testing Laboratories. Each vehicle was tested on a chassis dynamometer using a constant volume sampler, commercial fuels and standard duty cycles. Measurements included regulated pollutants such as carbon monoxide (CO), total hydrocarbons (THC), nitrogen oxides (NOx), and particulate matter (PM). Off-line analyses were performed to speciate gas- and particle-phase emissions. The data were used to investigate trends in emissions with vehicle age and to quantify the effects of different aftertreatment technologies on diesel vehicle emissions (e.g., with and without a diesel particulate filter). On average, newer LDGVs that met the most recent emissions standards had substantially lower emissions of regulated gaseous pollutants (CO, THC and NOx) than older vehicles. For example, THC emissions from the median LDGV that met the LEV2 standard was roughly a factor of 10 lower than the median pre-LEV vehicle; there were also substantial reductions in NOx (factor of ∼100) and CO (factor of ∼10) emissions from pre-LEV to LEV2 vehicles. However, reductions in LDGV PM mass emissions were much more modest. For example, PM emission from the median LEV2 vehicle was only a factor of three lower than the median pre-LEV vehicle, mainly due to the reductions in organic carbon emissions. In addition, LEV1 and LEV2 LDGVs had similar PM emissions. Catalyzed diesel particulate filters reduced CO, THC and PM emissions from HDDVs by one to two orders of magnitude. Comprehensive organic speciation was performed to quantify priority air toxic emissions and to estimate the secondary organic aerosol (SOA) formation potential. The data suggest that the SOA production from cold-start LDGVs exhaust will likely exceed primary PM emissions from LDGVs and could potentially exceed SOA formation from on-road diesel vehicles.

After 'dieselgate': Regulations or economic incentives for a successful environmental policy?

NASA Astrophysics Data System (ADS)

Zachariadis, Theodoros

2016-08-01

In September 2015 the U.S. Environmental Protection Agency announced that it started investigations against the automaker Volkswagen for illegally installing software that allowed some diesel-powered vehicle models to pass stringent emission tests for type-approval. Although generally prohibited, modern software makes it feasible for vehicles to detect an emission test and modulate engine operation or emission control accordingly. It has also been well known to experts worldwide - and readers of this Journal - that emission tests for motor vehicles are conducted with outdated test procedures which do not reflect today's actual driving conditions and enable automakers to exploit 'flexibilities' so as to yield artificially low emission results. For example, on-road carbon dioxide (CO2) emissions of cars that entered the European market in 2014 were reportedly 40% higher than their formal test emissions, while this gap was less than 10% in the early 2000s (Tietge et al., 2015). In the case of health-related pollutant nitrogen oxides (NOx), this gap seems to be markedly higher, in particular for diesel-powered cars (Weiss et al., 2012) - whereas this does not seem to be a serious problem for other air pollutants. In internal combustion engines of motor vehicles there is still a trade-off between NOx emissions and fuel efficiency (and hence CO2 emissions): a fast combustion with high temperatures is optimal for maximum fuel efficiency and minimum CO2 emissions, whereas these conditions give rise to higher NOx emissions. Conversely, NOx control techniques such as exhaust gas recirculation reduce combustion temperature and often lead to lower fuel efficiency. In short, it becomes ever more difficult for internal combustion engines to meet the increasingly stringent legislated standards for some air pollutants and carbon dioxide at the same time. This increases the probability of applying legal and illegal defeat strategies.

40 CFR 60.4320 - What emission limits must I meet for nitrogen oxides (NOX)?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false What emission limits must I meet for nitrogen oxides (NOX)? 60.4320 Section 60.4320 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... nitrogen oxides (NOX)? (a) You must meet the emission limits for NOX specified in Table 1 to this subpart...

40 CFR 60.4320 - What emission limits must I meet for nitrogen oxides (NOX)?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 6 2011-07-01 2011-07-01 false What emission limits must I meet for nitrogen oxides (NOX)? 60.4320 Section 60.4320 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... nitrogen oxides (NOX)? (a) You must meet the emission limits for NOX specified in Table 1 to this subpart...

40 CFR 60.4320 - What emission limits must I meet for nitrogen oxides (NOX)?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 7 2013-07-01 2013-07-01 false What emission limits must I meet for nitrogen oxides (NOX)? 60.4320 Section 60.4320 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... nitrogen oxides (NOX)? (a) You must meet the emission limits for NOX specified in Table 1 to this subpart...

40 CFR 60.4320 - What emission limits must I meet for nitrogen oxides (NOX)?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false What emission limits must I meet for nitrogen oxides (NOX)? 60.4320 Section 60.4320 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... nitrogen oxides (NOX)? (a) You must meet the emission limits for NOX specified in Table 1 to this subpart...

40 CFR 60.4320 - What emission limits must I meet for nitrogen oxides (NOX)?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 7 2012-07-01 2012-07-01 false What emission limits must I meet for nitrogen oxides (NOX)? 60.4320 Section 60.4320 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... nitrogen oxides (NOX)? (a) You must meet the emission limits for NOX specified in Table 1 to this subpart...

40 CFR 75.71 - Specific provisions for monitoring NOX and heat input for the purpose of calculating NOX mass...

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 17 2014-07-01 2014-07-01 false Specific provisions for monitoring NOX... MONITORING NOX Mass Emissions Provisions § 75.71 Specific provisions for monitoring NOX and heat input for...-diluent continuous emission monitoring system (consisting of a NOX pollutant concentration monitor, an O2...

40 CFR 75.71 - Specific provisions for monitoring NOX and heat input for the purpose of calculating NOX mass...

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 17 2012-07-01 2012-07-01 false Specific provisions for monitoring NOX... MONITORING NOX Mass Emissions Provisions § 75.71 Specific provisions for monitoring NOX and heat input for...-diluent continuous emission monitoring system (consisting of a NOX pollutant concentration monitor, an O2...

40 CFR 75.71 - Specific provisions for monitoring NOX and heat input for the purpose of calculating NOX mass...

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 17 2013-07-01 2013-07-01 false Specific provisions for monitoring NOX... MONITORING NOX Mass Emissions Provisions § 75.71 Specific provisions for monitoring NOX and heat input for...-diluent continuous emission monitoring system (consisting of a NOX pollutant concentration monitor, an O2...

Demonstration of Diesel Engine Air Emissions Reduction Technologies

DTIC Science & Technology

2008-12-01

16 Figure 5. Plots of Cheyenne Mountain Operating Cycle and Reference CBD Driving...Air Act CARB California Air Resources Board CBD Central Business District CCR California Code of Regulations CES Cummins Emissions Solutions CFR...matter ppb parts per billion ppm parts per million PuriNOx Proprietary Water / Diesel Emulsified Fuel RPF robust particulate filter THC total

An Alternative to NOx Cap-and-Trade Programs: An Exploratory Analysis of Charging NOx Emitters for Health Damages

NASA Astrophysics Data System (ADS)

Mauzerall, D. L.; Sultan, B.; Kim, N.; Bradford, D.

2003-12-01

To address the problem of elevated O3 concentrations throughout the northeastern United States in summer, a NOx cap-and-trade program was implemented that reduced NOx emissions from large point sources by nearly 50%. To determine whether this program has been successful, we examine O3, NO and temperature measurements collected in the EPA-AIRS network prior to and after the cap-and-trade program went into effect in 1999. Ambient NO concentrations as measured in the EPA-AIRS network are lower in the post-cap period in all months except July. We find that the upper half of the distribution of O3 concentrations within the region is essentially unchanged (or slightly higher) in May and June, modestly reduced in July and August (except the highest concentrations which are larger in August), and significantly lower in September (ranging from 0-20 ppb lower between the mean and highest concentrations) in the 1999-2001 post-cap period relative to the 1995-1998 pre-cap period. Except for September, the frequency with which the 80ppb 8-hour NAAQS standard for O3 is exceeded has not decreased. Temperatures during the post-cap period were slightly higher in June, July and August, and slightly lower in September - likely contributing to reduced O3 levels during September in the post-cap period. To explore the possibility that trading, or selective emissions over the course of the summer, could influence regional O3 concentrations, we conduct chemical transport modeling experiments using the CAMx regional model. Even within May-September for a single year, demands for electrical power and hence NOx emissions are greater during hot than cool periods. We demonstrate that substantially more O3 is produced from identical NOx emissions from a single power plant on high temperature than on low temperature days in July 1995. Thus a lack of temporal restrictions on when in a single summer month NOx emissions may occur can result in higher O3 levels. We also demonstrate that identical NOx emissions in regions of high (low) isoprene emission result in greater (lesser) O3 production. This indicates that NOx trades from locations with low to high isoprene emissions likely result in increases in O3 production. Since the objective of reducing O3 concentrations is to reduce the impact elevated O3 has on human health and welfare, we examine the mortalities that result from the O3 produced from a fixed NOx emission in the two cases described above as well as in regions of high and low population. We estimate substantially higher mortality rates from a unit NOx emission as a result of elevated O3 concentrations for high temperature days, in regions of high isoprene emissions, and for emissions occurring upwind of large populations. We attempt to assign a monetary value to the loss of life resulting from the enhanced O3 concentrations that result from these NOx emissions. We propose, as an alternative to NOx emissions cap and trade programs, a system by which NOx emitters are charged for the marginal damage they cause as a result of the O3 produced from the NOx they emit. Rather than resulting in a reduction in total NOx emissions without necessarily reducing O3 concentrations (as a cap-and-trade program does), this alternative system provides a direct incentive to reduce NOx emissions at times and places where they cause the most harm.

Evaluation of the impacts of biodiesel and second generation biofuels on NO(x) emissions for CARB diesel fuels.

PubMed

Hajbabaei, Maryam; Johnson, Kent C; Okamoto, Robert A; Mitchell, Alexander; Pullman, Marcie; Durbin, Thomas D

2012-08-21

The impact of biodiesel and second generation biofuels on nitrogen oxides (NO(x)) emissions from heavy-duty engines was investigated using a California Air Resources Board (CARB) certified diesel fuel. Two heavy-duty engines, a 2006 engine with no exhaust aftertreatment, and a 2007 engine with a diesel particle filter (DPF), were tested on an engine dynamometer over four different test cycles. Emissions from soy- and animal-based biodiesels, a hydrotreated renewable diesel, and a gas to liquid (GTL) fuel were evaluated at blend levels from 5 to 100%. NO(x) emissions consistently increased with increasing biodiesel blend level, while increasing renewable diesel and GTL blends showed NO(x) emissions reductions with blend level. NO(x) increases ranged from 1.5% to 6.9% for B20, 6.4% to 18.2% for B50, and 14.1% to 47.1% for B100. The soy-biodiesel showed higher NO(x) emissions increases compared to the animal-biodiesel. NO(x) emissions neutrality with the CARB diesel was achieved by blending GTL or renewable diesel fuels with various levels of biodiesel or by using di-tert-butyl peroxide (DTBP). It appears that the impact of biodiesel on NO(x) emissions might be a more important consideration when blended with CARB diesel or similar fuels, and that some form of NO(x) mitigation might be needed for biodiesel blends with such fuels.

40 CFR 75.1 - Purpose and scope.

Code of Federal Regulations, 2012 CFR

2012-07-01

... monitoring, recordkeeping, and reporting of NOX mass emissions with which EPA, individual States, or groups of States may require sources to comply in order to demonstrate compliance with a NOX mass emission... estimating SO2 mass emissions from gas-fired or oil-fired units and NOX emissions from gas-fired peaking or...

Impact of Clean Air Act Regulations on Nitrogen Fate and Transport in Neuse River Basin

EPA Science Inventory

This study investigated impacts of Clean Air Act Amendment (CAAA) NOx emissions regulations on the fate and transport of nitrogen for two watersheds in the Neuse River Basin, North Carolina, USA from 1990 to 2020. The Soil and Water Assessment Tool (SWAT) and the Community Multi-...

Effect of Hydrogen Addition on Methane HCCI Engine Ignition Timing and Emissions Using a Multi-zone Model

NASA Astrophysics Data System (ADS)

Wang, Zi-han; Wang, Chun-mei; Tang, Hua-xin; Zuo, Cheng-ji; Xu, Hong-ming

2009-06-01

Ignition timing control is of great importance in homogeneous charge compression ignition engines. The effect of hydrogen addition on methane combustion was investigated using a CHEMKIN multi-zone model. Results show that hydrogen addition advances ignition timing and enhances peak pressure and temperature. A brief analysis of chemical kinetics of methane blending hydrogen is also performed in order to investigate the scope of its application, and the analysis suggests that OH radical plays an important role in the oxidation. Hydrogen addition increases NOx while decreasing HC and CO emissions. Exhaust gas recirculation (EGR) also advances ignition timing; however, its effects on emissions are generally the opposite. By adjusting the hydrogen addition and EGR rate, the ignition timing can be regulated with a low emission level. Investigation into zones suggests that NOx is mostly formed in core zones while HC and CO mostly originate in the crevice and the quench layer.

Factors regulating ozone over the United States and its export to the global atmosphere

NASA Technical Reports Server (NTRS)

Jacob, Daniel J.; Logan, Jennifer A.; Gardner, Geraldine M.; Yevich, Rose M.; Spivakovsky, Clarisa M.; Wofsy, Steven C.; Sillman, Sanford; Prather, Michael J.

1993-01-01

Attention is given to the factors regulating summertime O3 over the U.S. and its export to the global atmosphere, which are examined via a 3-mo simulation involving a continental-scale 3D photochemical model. It is found that reducing NO(x) emissions by 50 percent from 1985 levels would decrease rural O3 concentrations over the eastern U.S. by about 15 percent under almost all meteorological conditions, while reducing anthropogenic hydrocarbon emissions by 50 percent would have less than a 4 percent effect except in the largest urban plumes. The correlation between O3 concentrations and temperature observed at eastern U.S. sites is attributed in part to the association of high temperatures with regional stagnation, and in part to an actual dependence of O3 production on temperature driven primarily by conversion of NO(x) to PAN.

Top-down NOX Emissions of European Cities Derived from Modelled and Spaceborne Tropospheric NO2 Columns

NASA Astrophysics Data System (ADS)

Verstraeten, W. W.; Boersma, K. F.; Douros, J.; Williams, J. E.; Eskes, H.; Delcloo, A. W.

2017-12-01

High nitrogen oxides (NOX = NO + NO2) concentrations near the surface impact humans and ecosystems badly and play a key role in tropospheric chemistry. NO2 is an important precursor of tropospheric ozone (O3) which in turn affects the production of the hydroxyl radical controlling the chemical lifetime of key atmospheric pollutants and reactive greenhouse gases. Combustion from industrial, traffic and household activities in large and densely populated urban areas result in high NOX emissions. Accurate mapping of these emissions is essential but hard to do since reported emissions factors may differ from real-time emissions in order of magnitude. Modelled NO2 levels and lifetimes also have large associated uncertainties and overestimation in the chemical lifetime which may mask missing NOX chemistry in current chemistry transport models (CTM's). The simultaneously estimation of both the NO2 lifetime and as well as the concentrations by applying the Exponentially Modified Gaussian (EMG) method on tropospheric NO2 columns lines densities should improve the surface NOX emission estimates. Here we evaluate if the EMG methodology applied on the tropospheric NO2 columns simulated by the LOTOS-EUROS (Long Term Ozone Simulation-European Ozone Simulation) CTM can reproduce the NOX emissions used as model input. First we process both the modelled tropospheric NO2 columns for the period April-September 2013 for 21 selected European urban areas under windy conditions (averaged vertical wind speeds between surface and 500 m from ECMWF > 2 m s-1) as well as the accompanying OMI (Ozone Monitoring Instrument) data providing us with real-time observation-based estimates of midday NO2 columns. Then we compare the top-down derived surface NOX emissions with the 2011 MACC-III emission inventory, used in the CTM as input to simulate the NO2 columns. For cities where NOX emissions can be assumed as originating from one large source good agreement is found between the top-down derived NOX emissions from CTM and OMI with the MACC-III inventory. For cities where multiple sources of NOX are observed (e.g. Brussels, London), an adapted methodology is required. For some cities such as St-Petersburg and Moscow the top-down NOX estimates from 2013 OMI data are biased low compared to the MACC-III inventory which uses a 2011 NOX emissions update.

Nitrogen oxides emissions from thermal power plants in china: current status and future predictions.

PubMed

Tian, Hezhong; Liu, Kaiyun; Hao, Jiming; Wang, Yan; Gao, Jiajia; Qiu, Peipei; Zhu, Chuanyong

2013-10-01

Increasing emissions of nitrogen oxides (NOx) over the Chinese mainland have been of great concern due to their adverse impacts on regional air quality and public health. To explore and obtain the temporal and spatial characteristics of NOx emissions from thermal power plants in China, a unit-based method is developed. The method assesses NOx emissions based on detailed information on unit capacity, boiler and burner patterns, feed fuel types, emission control technologies, and geographical locations. The national total NOx emissions in 2010 are estimated at 7801.6 kt, of which 5495.8 kt is released from coal-fired power plant units of considerable size between 300 and 1000 MW. The top provincial emitter is Shandong where plants are densely concentrated. The average NOx-intensity is estimated at 2.28 g/kWh, markedly higher than that of developed countries, mainly owing to the inadequate application of high-efficiency denitrification devices such as selective catalytic reduction (SCR). Future NOx emissions are predicted by applying scenario analysis, indicating that a reduction of about 40% by the year 2020 can be achieved compared with emissions in 2010. These results suggest that NOx emissions from Chinese thermal power plants could be substantially mitigated within 10 years if reasonable control measures were implemented effectively.

NOx emissions from Euro IV busses with SCR systems associated with urban, suburban and freeway driving patterns.

PubMed

Fu, Mingliang; Ge, Yunshan; Wang, Xin; Tan, Jianwei; Yu, Linxiao; Liang, Bin

2013-05-01

NOx and particulate matter (PM) emissions from heavy-duty diesel vehicles (HDVs) have become the most important sources of pollutants affecting urban air quality in China. In recent years, a series of emission control strategies and diesel engine polices have been introduced that require advanced emission control technology. China and Europe mostly have used Selective Catalytic Reduction (SCR) with urea to meet the Euro IV diesel engine emission standard. In this study, two Euro IV busses with SCR were tested by using potable emission measurement system (PEMS) to assess NOx emissions associated with urban, suburban and freeway driving patterns. The results indicated that with the SCR system, the urea injection time for the entire driving period increased with higher vehicle speed. For freeway driving, the urea injection time covered 71%-83% of the driving period; the NOx emission factors from freeway driving were lower than those associated with urban and suburban driving. Unfortunately, the NOx emission factors were 2.6-2.8-, 2.3-2.7- and 2.2-2.3-fold higher than the Euro IV standard limits for urban, suburban and freeway driving, respectively; NOx emission factors (in g/km and g/(kW·h)) from the original vehicles (without SCR) were higher than their corresponding vehicles with SCR for suburban and freeway driving. Compared with the IVE model results, the measured NOx emission factors were 1.60-1.16-, 1.77-1.27-, 2.49-2.44-fold higher than the NOx predicted by the IVE model for urban and suburban driving, respectively. Thus, an adjustment of emission factors is needed to improve the estimation of Euro IV vehicle emissions in China. Copyright © 2013 Elsevier B.V. All rights reserved.

40 CFR 97.524 - Compliance with TR NOX Ozone Season emissions limitation.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 22 2012-07-01 2012-07-01 false Compliance with TR NOX Ozone Season... TR NOX Ozone Season Trading Program § 97.524 Compliance with TR NOX Ozone Season emissions limitation. (a) Availability for deduction for compliance. TR NOX Ozone Season allowances are available to be...

40 CFR 97.524 - Compliance with TR NOX Ozone Season emissions limitation.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 22 2013-07-01 2013-07-01 false Compliance with TR NOX Ozone Season... TR NOX Ozone Season Trading Program § 97.524 Compliance with TR NOX Ozone Season emissions limitation. (a) Availability for deduction for compliance. TR NOX Ozone Season allowances are available to be...

40 CFR 97.524 - Compliance with TR NOX Ozone Season emissions limitation.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 21 2014-07-01 2014-07-01 false Compliance with TR NOX Ozone Season... TR NOX Ozone Season Trading Program § 97.524 Compliance with TR NOX Ozone Season emissions limitation. (a) Availability for deduction for compliance. TR NOX Ozone Season allowances are available to be...

Effect of reductive treatments on Pt behavior and NOx storage in lean NOx trap catalysts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Xianqin; Kim, Do Heui; Kwak, Ja Hun

2011-10-01

Lean NOx trap (LNT) catalysts represent a promising approach to meet increasingly stringent NOx emission regulations on diesel and other lean-burn engines. Pt material properties, including dispersion and particle size, are known to be important factors in determining NOx uptake performance, since Pt provides active sites for NO oxidation to NO2 necessary for storing NOx as nitrates, and for the reduction of nitrates to N2. In this work, the physicochemical properties of Pt in Pt-BaO/Al2O3 LNT catalysts, such as the Pt accessible surface area and particle size, were investigated by using various tools, such as irreversible volumetric H2 chemisorption, highmore » resolution transmission electron microscopy (HRTEM), and X-ray diffraction (XRD), following successive reductive treatments at elevated temperatures. NOx uptake activities were also measured to establish a relationship between the properties of Pt and NOx storage following identical high-temperature reductive treatments. We find that the reductive treatments of Pt-BaO/Al2O3 lean NOx trap catalysts at temperatures up to 500 ºC promote a significant increase in NOx uptake explained, in part, by an induced close interaction between Pt and BaO phases in the catalyst, thus enabling facilitation of the NOx storage process.« less

Top-down NOX emissions over European cities from LOTOS-EUROS simulated and OMI observed tropospheric NO2 columns using the Exponentially Modified Gaussian approach

NASA Astrophysics Data System (ADS)

Verstraeten, Willem W.; Folkert Boersma, K.; Douros, John; Williams, Jason E.; Eskes, Henk H.; Delcloo, Andy

2017-04-01

High nitrogen oxides concentrations at the surface (NOX = NO + NO2) impact humans and ecosystem badly and play a key role in tropospheric chemistry. Surface NOX emissions drive major processes in regional and global chemistry transport models (CTM). NOX contributes to the formation of acid rain, act as aerosol precursors and is an important trace gas for the formation of tropospheric ozone (O3). Via tropospheric O3, NOX indirectly affects the production of the hydroxyl radical which controls the chemical lifetime of key atmospheric pollutants and reactive greenhouse gases. High NOX emissions are mainly observed in polluted regions produced by anthropogenic combustion from industrial, traffic and household activities typically observed in large and densely populated urban areas. Accurate NOX inventories are essential, but state-of the- art emission databases may vary substantially and uncertainties are high since reported emissions factors may differ in order of magnitude and more. To date, the modelled NO2 concentrations and lifetimes have large associated uncertainties due to the highly non-linear small-scale chemistry that occurs in urban areas and uncertainties in the reaction rate data, missing nitrogen (N) species and volatile organic compounds (VOC) emissions, and incomplete knowledge of nitrogen oxides chemistry. Any overestimation in the chemical lifetime may mask missing NOX chemistry in current CTM's. By simultaneously estimating both the NO2 lifetime and concentrations, for instance by using the Exponentially Modified Gaussian (EMG), a better surface NOX emission flux estimate can be obtained. Here we evaluate if the EMG methodology can reproduce the emissions input from the tropospheric NO2 columns simulated by the LOTOS-EUROS (Long Term Ozone Simulation-European Ozone Simulation) CTM model. We apply the EMG methodology on LOTOS-EUROS simulated tropospheric NO2 columns for the period April-September 2013 for 21 selected European urban areas under windy conditions (surface wind speeds > 3 m s-1). We then compare the top-down derived surface NOX emissions with the 2011 MACC-III emission inventory, used in the LOTOS-EUROS model as input to simulate the NO2 columns. We also apply the EMG methodology on OMI (Ozone Monitoring Instrument) tropospheric NO2 column data, providing us with real-time observation-based estimates of midday NO2 lifetime and NOX emissions over 21 European cities in 2013. Results indicate that the top-down derived NOX emissions from LOTOS-EUROS (respectively OMI) are comparable with the MACC-III inventory with a R2 of 0.99 (respectively R2 = 0.79). For St-Petersburg and Moscow the top-down NOX estimates from 2013 OMI data are biased low compared to the MACC-III inventory which uses a 2011 NOX emissions update.

Study of Nox Emission Characteristics of a 1025t/h Coal-Fired Circulating Fluidized Bed Boiler

NASA Astrophysics Data System (ADS)

Li, Q. Y.; Mi, Z. D.; Zhang, Q. F.

Measurements of emission are carried out in a 1025t/h CFB boiler. The effect of some factors including coal properties, bed temperature, unit load, excess air on the emission of NOx are investigated. The measurement results show that the N concentration in the coal is dominant parameter to predict the NOx emission from a large-scale CFB boiler. NOx emission from the 1025t/h CFB boiler increases with cyclone temperature and upper pressure drop due to post combustion and external cycle.

[Experimental investigation on emission characteristic of NOx during micropulverized coal oxidation].

PubMed

Jiang, Xiu-Min; Wei, Li-Hong; Huang, Xiang-Yong; Zhang, Chao-Qun

2008-03-01

The combustion experiments of HG micronized coal have been conducted by combining DTG and GC-MS. The effects on NOx emission caused by particle size, oxygen concentration and heating rate were analyzed. The results show that under combustion condition that oxygen concentration is 20%, NOx precipitations of HG coal in difference sizes are single-peaked courses. Particle size impacts NOx emission from coal combustion significantly. Micro-pulverized coal reduces NOx emission. Under heating condition with 5 degrees C/min, 10 degrees C/min and 20 degrees C/min, precipitation of NO and NO2 is increased with heating rate rising, and temperature parallelized with maximum NO precipitation rate is increased with heating rate rising as well. With increasing of oxygen concentration in combustion, NOx precipitation increases correspondingly, and temperature parallelized with maximum NOx precipitation rate is reduced.

Low NO(x) potential of gas turbine engines

NASA Technical Reports Server (NTRS)

Tacina, Robert R.

1990-01-01

The purpose is to correlate emission levels of gas turbine engines. The predictions of NO(x) emissions are based on a review of the literature of previous low NO(x) combustor programs and analytical chemical kinetic calculations. Concepts included in the literature review consisted of lean-premixed-prevaporized (LPP), rich burn/quick quench/lean burn (RQL), and direct injection. The NO(x) emissions were found to be an exponential function of adiabatic combustion temperature over a wide range of inlet temperatures, pressures and (lean) fuel-air ratios. A simple correlation of NO(x) formation with time was not found. The LPP and direct injection (using gaseous fuels) concepts have the lowest NO(x) emissions of the three concepts. The RQL data has higher values of NO(x) than the LPP concept, probably due to the stoichiometric temperatures and NO(x) production that occur during the quench step. Improvements in the quick quench step could reduce the NO(x) emissions to the LPP levels. The low NO(x) potential of LPP is offset by the operational disadvantages of its narrow stability limits and its susceptibility to autoignition/flashback. The Rich-Burn/Quick-Quench/Lean-Burn (RQL) and the direct injection concepts have the advantage of wider stability limits comparable to conventional combustors.

40 CFR 96.374 - Recordkeeping and reporting.

Code of Federal Regulations, 2011 CFR

2011-07-01

... quarterly reports, as follows: (1) If the CAIR NOX Ozone Season unit is subject to an Acid Rain emissions... not subject to an Acid Rain emissions limitation or a CAIR NOX emissions limitation, then the CAIR... are also subject to an Acid Rain emissions limitation or the CAIR NOX Annual Trading Program or CAIR...

40 CFR 96.374 - Recordkeeping and reporting.

Code of Federal Regulations, 2013 CFR

2013-07-01

... quarterly reports, as follows: (1) If the CAIR NOX Ozone Season unit is subject to an Acid Rain emissions... not subject to an Acid Rain emissions limitation or a CAIR NOX emissions limitation, then the CAIR... are also subject to an Acid Rain emissions limitation or the CAIR NOX Annual Trading Program or CAIR...

40 CFR 96.374 - Recordkeeping and reporting.

Code of Federal Regulations, 2012 CFR

2012-07-01

... quarterly reports, as follows: (1) If the CAIR NOX Ozone Season unit is subject to an Acid Rain emissions... not subject to an Acid Rain emissions limitation or a CAIR NOX emissions limitation, then the CAIR... are also subject to an Acid Rain emissions limitation or the CAIR NOX Annual Trading Program or CAIR...

40 CFR 96.374 - Recordkeeping and reporting.

Code of Federal Regulations, 2014 CFR

2014-07-01

... quarterly reports, as follows: (1) If the CAIR NOX Ozone Season unit is subject to an Acid Rain emissions... not subject to an Acid Rain emissions limitation or a CAIR NOX emissions limitation, then the CAIR... are also subject to an Acid Rain emissions limitation or the CAIR NOX Annual Trading Program or CAIR...

Emissions of NOx, SO2, CO, and HCHO from commercial marine shipping during Texas Air Quality Study (TexAQS) 2006

NASA Astrophysics Data System (ADS)

Williams, E. J.; Lerner, B. M.; Murphy, P. C.; Herndon, S. C.; Zahniser, M. S.

2009-11-01

We report measurements of NOx, SO2, CO, and HCHO mass-based emission factors from more than 200 commercial vessel encounters in the Gulf of Mexico and the Houston-Galveston region of Texas during August and September, 2006. For underway ships, bulk freight carriers have the highest average NOx emissions at ˜87 g NOx (kg fuel)-1, followed by tanker ships at ˜79 g NOx (kg fuel)-1, while container carriers, passenger ships, and tugs all emit an average of about ˜60 g NOx (kg fuel)-1. Emission of NOx from stationary vessels was lower, except for container ships and tugs, and likely reflects use of medium-speed diesel engines. Overall, our mean NOx emission factors are 10-15% lower than published data. Average emission of SO2 was lower for passenger ships and tugs and tows (6-7 g SO2 (kg fuel)-1) than for larger cargo vessels (20-30 g SO2 (kg fuel)-1). Our data for large cargo ships in this region indicate an average residual fuel sulfur content of ˜1.4% which is a factor of two lower than the global average of 2.7%. Emission of CO was low for all categories (7-16 g CO (kg fuel)-1), although our mean overall CO emission factor is about 10% higher than published data. Emission of HCHO was less than 5% that of CO. Despite considerable variability, no functional relationships, such as emissions changes with engine speed or load, could be discerned. Comparison of emission factors from ships to those from other sources suggests ship emissions in this region cannot be ignored.

40 CFR 75.19 - Optional SO2, NOX, and CO2 emissions calculation for low mass emissions (LME) units.

Code of Federal Regulations, 2010 CFR

2010-07-01

...), manufacturer and model, and must have the same history of modifications (e.g., have the same controls installed... (or group of identical units) equipped with SCR (or SNCR) and uses dry low-NOX technology to control... with add-on NOX emission controls, and for units that use dry low-NOX technology, the owner or operator...

Combustion and NOx emissions in deep-air-staging combustion of char in a circulating fluidized bed

NASA Astrophysics Data System (ADS)

Gong, Zhiqiang; Wang, Zhentong; Wang, Lei; Du, Aixun

2017-10-01

Combustion and NOx emissions in deep-air-staging (with higher level secondary air (SA) injection) combustion of char have been investigated in a CFB test rig. A good fluidized condition and uniform temperature distribution can be achieved with injection of higher level SA. NOx emission decreases with injection of higher level SA and the reduction effect is more obvious at higher temperature. NOx emission decreases with combustion temperature increasing for char combustion.

40 CFR 86.319-79 - Analyzer checks and calibrations; frequency and overview.

Code of Federal Regulations, 2013 CFR

2013-07-01

... ENGINES Emission Regulations for New Gasoline-Fueled and Diesel-Fueled Heavy-Duty Engines; Gaseous Exhaust... testing, check the NOX converter efficiency, as described in § 86.332. (c) At least once every 30 days...

40 CFR 86.319-79 - Analyzer checks and calibrations; frequency and overview.

Code of Federal Regulations, 2012 CFR

2012-07-01

... ENGINES Emission Regulations for New Gasoline-Fueled and Diesel-Fueled Heavy-Duty Engines; Gaseous Exhaust... testing, check the NOX converter efficiency, as described in § 86.332. (c) At least once every 30 days...

40 CFR 86.319-79 - Analyzer checks and calibrations; frequency and overview.

Code of Federal Regulations, 2011 CFR

2011-07-01

... ENGINES Emission Regulations for New Gasoline-Fueled and Diesel-Fueled Heavy-Duty Engines; Gaseous Exhaust... testing, check the NOX converter efficiency, as described in § 86.332. (c) At least once every 30 days...

Nitrogen isotopes as indicators of NOx source contributions to atmospheric nitrate deposition across the midwestern and northeastern United States

USGS Publications Warehouse

Elliott, E.M.; Kendall, C.; Wankel, Scott D.; Burns, Douglas A.; Boyer, E.W.; Harlin, K.; Bain, D.J.; Butler, T.J.

2007-01-01

Global inputs of NOx are dominated by fossil fuel combustion from both stationary and vehicular sources and far exceed natural NOx sources. However, elucidating NOx sources to any given location remains a difficult challenge, despite the need for this information to develop sound regulatory and mitigation strategies. We present results from a regional-scale study of nitrogen isotopes (??15N) in wet nitrate deposition across 33 sites in the midwestern and northeastern U.S. We demonstrate that spatial variations in ??15N are strongly correlated with NOx emissions from surrounding stationary sources and additionally that ??15N is more strongly correlated with surrounding stationary source NOx emissions than pH, SO 42-, or NO3- concentrations. Although emission inventories indicate that vehicle emissions are the dominant NOx source in the eastern U.S., our results suggest that wet NO 3- deposition at sites in this study is strongly associated with NOx emissions from stationary sources. This suggests that large areas of the landscape potentially receive atmospheric NOy deposition inputs in excess of what one would infer from existing monitoring data alone. Moreover, we determined that spatial patterns in ??15N values are a robust indicator of stationary NOx contributions to wet NO3- deposition and hence a valuable complement to existing tools for assessing relationships between NO 3- deposition, regional emission inventories, and for evaluating progress toward NOx reduction goals. ?? 2007 American Chemical Society.

The National Emissions Inventory Significantly Overestimates NOx Emissions: Analysis of CMAQ and in situ observations from DISCOVER-AQ

NASA Astrophysics Data System (ADS)

Anderson, D. C.; Dickerson, R. R.; Loughner, C.

2013-12-01

NOx and CO not only adversely impact human health, but they, along with associated VOCs, are also important precursors for O3 formation. While ambient NOx and CO concentrations have decreased dramatically over the past 10-20 years, O3 has remained a more recalcitrant problem, particularly in the Baltimore/Washington region. Reduction of O3 production requires that emissions inventories, such as the National Emissions Inventory (NEI), accurately capture total emissions of CO and NOx while also correctly apportioning them among different sectors. Previous evaluations of the NEI paint different pictures of its accuracy, with assertions that it overestimates either one or both of CO and NOx from anywhere between 25 percent to a factor of 2. These conflicting claims warrant further investigation. In this study, measurements of NOx and CO taken aboard the NOAA P3B airplane during the 2011 DISCOVER-AQ field campaign were used to determine the NOx/CO emissions ratio at 6 locations in the Washington/Baltimore region. An average molar emissions ratio of 12.8 × 1.2 CO/NOx was found by calculating the change in CO over the change in NOx from vertical concentration profiles in the planetary boundary layer. Ratios showed little variation with location. Observed values were approximately a factor of 1.35 - 1.75 times greater than that predicted by the annual, countywide emissions ratio from the 2008 NEI. When compared to a temporalized, gridded version of the inventory processed by SMOKE, ratio observations were greater than that predicted by inventories by up to a factor of 2. Comparison of the in situ measurements and remotely sensed observations from MOPITT of CO to the Community Multiscale Air Quality (CMAQ) model agree within 10-35 percent, with the model higher on average. Measurements of NOy by two separate analytical techniques, on the other hand, show that CMAQ consistently and significantly overestimates NOy concentrations. Combined with the CO observations, this indicates that the NEI overestimates NOx emissions by approximately a factor of 2. Comparison of the temporalized NEI to continuous monitoring of NOx emissions from point sources shows that, on average, agreement between observations and the NEI were within 5 percent. In a region where the NEI estimates on-road emissions can account for 50-75 percent of total NOx, the most likely source of error in the NOx inventory is in the on-road sector. Assumptions about the lifetime and efficacy of catalytic converters in the MOVES model should be investigated as a possible source of this error.

Top-down NOx and SO2 emissions simultaneously estimated from different OMI retrievals and inversion frameworks

NASA Astrophysics Data System (ADS)

Qu, Z.; Henze, D. K.; Wang, J.; Xu, X.; Wang, Y.

2017-12-01

Quantifying emissions trends of nitrogen oxides (NOx) and sulfur dioxide (SO2) is important for improving understanding of air pollution and the effectiveness of emission control strategies. We estimate long-term (2005-2016) global (2° x 2.5° resolution) and regional (North America and East Asia at 0.5° x 0.667° resolution) NOx emissions using a recently developed hybrid (mass-balance / 4D-Var) method with GEOS-Chem. NASA standard product and DOMINO retrievals of NO2 column are both used to constrain emissions; comparison of these results provides insight into regions where trends are most robust with respect to retrieval uncertainties, and highlights regions where seemingly significant trends are retrieval-specific. To incorporate chemical interactions among species, we extend our hybrid method to assimilate NO2 and SO2 observations and optimize NOx and SO2 emissions simultaneously. Due to chemical interactions, inclusion of SO2 observations leads to 30% grid-scale differences in posterior NOx emissions compared to those constrained only by NO2 observations. When assimilating and optimizing both species in pseudo observation tests, the sum of the normalized mean squared error (compared to the true emissions) of NOx and SO2 posterior emissions are 54-63% smaller than when observing/constraining a single species. NOx and SO2 emissions are also correlated through the amount of fuel combustion. To incorporate this correlation into the inversion, we optimize seven sector-specific emission scaling factors, including industry, energy, residential, aviation, transportation, shipping and agriculture. We compare posterior emissions from inversions optimizing only species' emissions, only sector-based emissions, and both species' and sector-based emissions. In situ measurements of NOx and SO2 are applied to evaluate the performance of these inversions. The impacts of the inversion on PM2.5 and O3 concentrations and premature deaths are also evaluated.

Satellite-based emission constraint for nitrogen oxides: Capability and uncertainty

NASA Astrophysics Data System (ADS)

Lin, J.; McElroy, M. B.; Boersma, F.; Nielsen, C.; Zhao, Y.; Lei, Y.; Liu, Y.; Zhang, Q.; Liu, Z.; Liu, H.; Mao, J.; Zhuang, G.; Roozendael, M.; Martin, R.; Wang, P.; Spurr, R. J.; Sneep, M.; Stammes, P.; Clemer, K.; Irie, H.

2013-12-01

Vertical column densities (VCDs) of tropospheric nitrogen dioxide (NO2) retrieved from satellite remote sensing have been employed widely to constrain emissions of nitrogen oxides (NOx). A major strength of satellite-based emission constraint is analysis of emission trends and variability, while a crucial limitation is errors both in satellite NO2 data and in model simulations relating NOx emissions to NO2 columns. Through a series of studies, we have explored these aspects over China. We separate anthropogenic from natural sources of NOx by exploiting their different seasonality. We infer trends of NOx emissions in recent years and effects of a variety of socioeconomic events at different spatiotemporal scales including the general economic growth, global financial crisis, Chinese New Year, and Beijing Olympics. We further investigate the impact of growing NOx emissions on particulate matter (PM) pollution in China. As part of recent developments, we identify and correct errors in both satellite NO2 retrieval and model simulation that ultimately affect NOx emission constraint. We improve the treatments of aerosol optical effects, clouds and surface reflectance in the NO2 retrieval process, using as reference ground-based MAX-DOAS measurements to evaluate the improved retrieval results. We analyze the sensitivity of simulated NO2 to errors in the model representation of major meteorological and chemical processes with a subsequent correction of model bias. Future studies will implement these improvements to re-constrain NOx emissions.

Greenhouse gas emissions trading in U.S. States: observations and lessons from the OTC NOx Budget Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andrew Aulisi; Alexander E. Farrell; Jonathan Pershing

2005-07-01

A number of U.S. states are considering market-based policies to reduce emissions of greenhouse gases (GHGs). The experience gained from emissions trading for sulfur dioxide and oxides of nitrogen (NOx) offers a useful body of information and data to draw on to design a GHG emissions trading system. This report examines NOx trading under the Ozone Transport Commission (OTC) NOx Budget Program, which resulted principally from the leadership, decisions, and actions by a group of states, ultimately becoming the first multilateral cap-and-trade system for emissions of air pollutants. 72 refs.

Development of a Comprehensive Community Nitrogen Oxide Emissions Reduction Toolkit (CCNERT)

NASA Astrophysics Data System (ADS)

Sung, Yong Hoon

The main objective of this study is to research and develop a simplified tool to estimate energy use in a community and its associated effects on air pollution. This tool is intended to predict the impacts of selected energy conservation options and efficiency programs on emission reduction. It is intended to help local government and their residents understand and manage information collection and the procedures to be used. This study presents a broad overview of the community-wide energy use and NOx emissions inventory process. It also presents various simplified procedures to estimate each sector's energy use. In an effort to better understand community-wide energy use and its associated NOx emissions, the City of College Station, Texas, was selected as a case study community for this research. While one community might successfully reduce the production of NOx emissions by adopting electricity efficiency programs in its buildings, another community might be equally successful by changing the mix of fuel sources used to generate electricity, which is consumed by the community. In yet a third community low NOx automobiles may be mandated. Unfortunately, the impact and cost of one strategy over another changes over time as major sources of pollution are reduced. Therefore, this research proposes to help community planners answer these questions and to assist local communities with their NOx emission reduction plans by developing a Comprehensive Community NOx Emissions Reduction Toolkit (CCNERT). The proposed simplified tool could have a substantial impact on reducing NOx emission by providing decision-makers with a preliminary understanding about the impacts of various energy efficiency programs on emissions reductions. To help decision makers, this study has addressed these issues by providing a general framework for examining how a community's non-renewable energy use leads to NOx emissions, by quantifying each end-user's energy usage and its associated NOx emissions, and by evaluating the environmental benefits of various types of energy saving options.

Estimates of the changes in tropospheric chemistry which result from human activity and their dependence on NO(x) emissions and model resolution

NASA Technical Reports Server (NTRS)

Kanakidou, Maria; Crutzen, Paul J.; Zimmermann, Peter H.

1994-01-01

As a consequence of the non-linear behavior of the chemistry of the atmosphere and because of the short lifetime of nitrogen oxides (NO(x)), two-dimensional models do not give an adequate description of the production and destruction rates of NO(x) and their effects on the distributions of the concentration of ozone and hydroxyl radical. In this study, we use a three-dimensional model to evaluate the contribution of increasing NO(x) emissions from industrial activity and biomass burning to changes in the chemical composition of the troposphere. By comparing results obtained from longitudinally-uniform and longitudinally-varying emissions of NO(x), we demonstrate that the geographical representation of the NO(x) emissions is crucial in simulating tropospheric chemistry.

CONTROL OF NOX EMISSIONS FROM U.S. COAL-FIRED ELECTRIC UTILITY BOILERS

EPA Science Inventory

The paper discusses the control of nitrogen oxide (NOx) emissions from U.S. coal-fired electric utility boilers. (NOTE: In general, NOx control technologies are categorized as being either primary or secondary control technologies. Primary technologies reduce the amount of NOx pr...

New insights from comprehensive on-road measurements of NOx, NO2 and NH3 from vehicle emission remote sensing in London, UK

NASA Astrophysics Data System (ADS)

Carslaw, David C.; Rhys-Tyler, Glyn

2013-12-01

In this paper we report the first direct measurements of nitrogen dioxide (NO2) in the UK using a vehicle emission remote sensing technique. Measurements of NO, NO2 and ammonia (NH3) from almost 70,000 vehicles were made spanning vehicle model years from 1985 to 2012. These measurements were carefully matched with detailed vehicle information data to understand the emission characteristics of a wide range of vehicles in a detailed way. Overall it is found that only petrol fuelled vehicles have shown an appreciable reduction in total NOx emissions over the past 15-20 years. Emissions of NOx from diesel vehicles, including those with after-treatment systems designed to reduce emissions of NOx, have not reduced over the same period of time. It is also evident that the vehicle manufacturer has a strong influence on emissions of NO2 for Euro 4/5 diesel cars and urban buses. Smaller-engined Euro 4/5 diesel cars are also shown to emit less NO2 than larger-engined vehicles. It is shown that NOx emissions from urban buses fitted with Selective Catalytic Reduction (SCR) are comparable to those using Exhaust Gas Recirculation for Euro V vehicles, while reductions in NOx of about 30% are observed for Euro IV and EEV vehicles. However, the emissions of NO2 vary widely dependent on the bus technology used. Almost all the NOx emission from Euro IV buses with SCR is in the form of NO, whereas EEV vehicles (Enhanced Environmentally friendly Vehicle) emit about 30% of the NOx as NO2. We find similarly low amounts of NO2 from trucks (3.5-12t and >12t). Finally, we show that NH3 emissions are most important for older generation catalyst-equipped petrol vehicles and SCR-equipped buses. The NH3 emissions from petrol cars have decreased by over a factor of three from the vehicles manufactured in the late 1990s compared with those manufactured in 2012. Tables of emission factors are presented for NOx, NO2 and NH3 together with uncertainties to assist the development of new emission inventories.

Characterization of NOx emission in the suburbs of Tokyo based on simultaneous and real-time observations of atmospheric Ox and NOx

NASA Astrophysics Data System (ADS)

Matsumoto, J.

2013-12-01

Nitrogen oxides, NOx (NO, NO2), and volatile organic compounds, VOCs, are important as precursors of photochemical oxidants (tropospheric ozone, O3). To predict and control photochemical oxidants, NOx emission should be captured precisely. In addition, the ratio of NO2/NOx in the exhaust gas is also important as the initial balance between NO and NO2 in the atmosphere. Monitoring the NO2/NOx ratio in the exhaust gases is essential. Especially, the influence of the NOx emission on the real atmosphere should be explored. However, conversion reactions among NO, NO2 and O3 are typically in the time scale of minutes. The NO2/NOx ratio can change rapidly just after emission. Real-time observations of these compounds in the second time scale are essential. In view of photochemical oxidant, near emission sources of NO, ozone concentration can be easily perturbed by reaction with locally emitted NO. As an index of oxidant, the sum of O3 and NO2 (Ox = O3 + NO2) is useful. In this study, a simultaneous and real-time analyzer of atmospheric Ox and NOx has been developed utilizing the dual NO2 detectors based on laser-induced fluorescence technique (LIF), and characterization of NOx emission was explored through the observations of Ox and NOx in the suburbs of Tokyo. The dual LIF detectors consisted of one laser head, two LIF cells, and one common vacuum pump. As the Ox monitor, the excess NO was added to the sample and O3 was converted to NO2, and then the sum of O3 and NO2 in the sample was quantified at the 1st LIF cell. As the NOx monitor, the excess O3 was added to the sample and NO was converted to NO2, and then the sum of NO and NO2 in the sample was quantified at the 2nd LIF cell. Both the ';Ox' and ';NOx' channels in the dual LIF analyzer were simultaneously monitoring Ox and NOx in the sample air, respectively. The temporal resolution of observed data was 1 s. Typical conversion efficiencies of O3 and NO to NO2 were more than 0.98. The lower detection limits were 0.1 ppbv for Ox and 0.5 ppbv for NOx (60-s integration, S/N = 3). The observation test in the suburbs of Tokyo was conducted in April 2013 at Tokorozawa Campus, Waseda University. During the campaign, 48 cases of ';NOx spikes', for which NOx levels significantly varied in the second time scale due to local NOx emission, were captured. NO2/NOx ratio in the exhaust gas was estimated as the slope of regression line between 1-s series data of Ox and those of NOx observed during each spike. The average of acquired NO2/NOx ratio was 0.10. Thus, as a result of observations of real atmosphere, the present NO2/NOx ratio in the exhaust gases in the suburbs of Tokyo was 0.10 as average, which was mainly due to exhausts of automobiles. However, when the individual cases were considered, NO2/NOx could vary from 0.00 to 0.30. Such a wide range of NO2/NOx ratio may be due to (1) difference of source types (eg. automobiles, power generator) and (2) difference of conditions of sources (eg. engines, filters of exhaust). For example, NO2/NOx ratio for hybrid electric vehicles may be different from those for conventional cars. When diffusion of such new model cars can change NOx emission in near future, the present method of simultaneous and real-time monitoring of Ox and NOx in the atmosphere can be useful and promising for characterization of NOx emission.

Global Partitioning of NOx Sources Using Satellite Observations: Relative Roles of Fossil Fuel Combustion, Biomass Burning and Soil Emissions

NASA Technical Reports Server (NTRS)

Jaegle, Lyatt; Steinberger, Linda; Martin, Randall V.; Chance, Kelly

2005-01-01

This document contains the following abstract for the paper "Global partitioning of NOx sources using satellite observations: Relative roles of fossil fuel combustion, biomass burning and soil emissions." Satellite observations have been used to provide important new information about emissions of nitrogen oxides. Nitrogen oxides (NOx) are significant in atmospheric chemistry, having a role in ozone air pollution, acid deposition and climate change. We know that human activities have led to a three- to six-fold increase in NOx emissions since pre-industrial times, and that there are three main surface sources of NOx: fuel combustion, large-scale fires, and microbial soil processes. How each of these sources contributes to the total NOx emissions is subject to some doubt, however. The problem is that current NOx emission inventories rely on bottom-up approaches, compiling large quantities of statistical information from diverse sources such as fuel and land use, agricultural data, and estimates of burned areas. This results in inherently large uncertainties. To overcome this, Lyatt Jaegle and colleagues from the University of Washington, USA, used new satellite observations from the Global Ozone Monitoring Experiment (GOME) instrument. As the spatial and seasonal distribution of each of the sources of NOx can be clearly mapped from space, the team could provide independent topdown constraints on the individual strengths of NOx sources, and thus help resolve discrepancies in existing inventories. Jaegle's analysis of the satellite observations, presented at the recent Faraday Discussion on "Atmospheric Chemistry", shows that fuel combustion dominates emissions at northern mid-latitudes, while fires are a significant source in the Tropics. Additionally, she discovered a larger than expected role for soil emissions, especially over agricultural regions with heavy fertilizer use. Additional information is included in the original extended abstract.

Enhanced Oxidation Capacity from Photolytic HOx/NOx Recycling: Implications for CH4 Growth

NASA Astrophysics Data System (ADS)

Madronich, S.

2017-12-01

Oxidation by OH radicals converts many emitted compounds (CO, CH4, VOCs as well as NOx, SO2, HCFCs, and others) to more soluble forms that can be removed rapidly from the atmosphere, e.g., by deposition. In a chemically stable atmosphere (without runaway concentration growth) the rate of OH production must generally exceed the emission rates of the reduced compounds, but secondary chemistry complicates OH budgets. If emission rates (e.g., E for CH4) increase, OH concentrations can either decrease or increase depending on NOx conditions, causing a non-linear dependence of CH4 concentrations on its emissions, [CH4] Ef where f, the methane feedback factor, is currently estimated in global 3d models to be 1.3-1.4. This feature is robust among models, and can be reproduced in simpler box models with the canonical Ox-HOx-NOx chemistry, in which global OH is increased by NOx emissions and decreased by CO, CH4, and VOC emissions. Scenarios with lower NOx emissions but higher CH4 emissions point to substantially lower global oxidation capacity in the future. Several newly hypothesized processes have attracted attention in recent years, including the photolytic recycling of OH from biogenic VOCs, and the photolysis of particulate nitrates to regenerate NOx. The latter process could be particularly significant in regions far from NOx emissions, where low NOx levels are more efficient at generating O3 and OH. To the extent that these processes do occur, they may provide some buffering of global OH against CH4 variations (f nearer 1), and more generally against anthropogenic perturbations. However, critical measurements from both lab and field are needed to assess the importance of these proposed processes.

40 CFR 75.12 - Specific provisions for monitoring NOX emission rate.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) AIR PROGRAMS (CONTINUED) CONTINUOUS EMISSION MONITORING Monitoring Provisions § 75.12 Specific provisions for monitoring NOX emission rate. (a) Coal-fired units, gas-fired nonpeaking units or oil-fired... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Specific provisions for monitoring NOX...

40 CFR 75.12 - Specific provisions for monitoring NOX emission rate.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) AIR PROGRAMS (CONTINUED) CONTINUOUS EMISSION MONITORING Monitoring Provisions § 75.12 Specific provisions for monitoring NOX emission rate. (a) Coal-fired units, gas-fired nonpeaking units or oil-fired... 40 Protection of Environment 17 2013-07-01 2013-07-01 false Specific provisions for monitoring NOX...

40 CFR 75.12 - Specific provisions for monitoring NOX emission rate.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) AIR PROGRAMS (CONTINUED) CONTINUOUS EMISSION MONITORING Monitoring Provisions § 75.12 Specific provisions for monitoring NOX emission rate. (a) Coal-fired units, gas-fired nonpeaking units or oil-fired... 40 Protection of Environment 17 2014-07-01 2014-07-01 false Specific provisions for monitoring NOX...

40 CFR 75.12 - Specific provisions for monitoring NOX emission rate.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) AIR PROGRAMS (CONTINUED) CONTINUOUS EMISSION MONITORING Monitoring Provisions § 75.12 Specific provisions for monitoring NOX emission rate. (a) Coal-fired units, gas-fired nonpeaking units or oil-fired... 40 Protection of Environment 16 2011-07-01 2011-07-01 false Specific provisions for monitoring NOX...

40 CFR 75.12 - Specific provisions for monitoring NOX emission rate.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) AIR PROGRAMS (CONTINUED) CONTINUOUS EMISSION MONITORING Monitoring Provisions § 75.12 Specific provisions for monitoring NOX emission rate. (a) Coal-fired units, gas-fired nonpeaking units or oil-fired... 40 Protection of Environment 17 2012-07-01 2012-07-01 false Specific provisions for monitoring NOX...

40 CFR 96.375 - Petitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... designated representative of a CAIR NOX Ozone Season unit that is subject to an Acid Rain emissions... designated representative of a CAIR NOX Ozone Season unit that is not subject to an Acid Rain emissions... designated representative of a CAIR NOX Ozone Season unit that is subject to an Acid Rain emissions...

40 CFR 96.375 - Petitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... designated representative of a CAIR NOX Ozone Season unit that is subject to an Acid Rain emissions... designated representative of a CAIR NOX Ozone Season unit that is not subject to an Acid Rain emissions... designated representative of a CAIR NOX Ozone Season unit that is subject to an Acid Rain emissions...

40 CFR 96.375 - Petitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... designated representative of a CAIR NOX Ozone Season unit that is subject to an Acid Rain emissions... designated representative of a CAIR NOX Ozone Season unit that is not subject to an Acid Rain emissions... designated representative of a CAIR NOX Ozone Season unit that is subject to an Acid Rain emissions...

40 CFR 96.375 - Petitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... designated representative of a CAIR NOX Ozone Season unit that is subject to an Acid Rain emissions... designated representative of a CAIR NOX Ozone Season unit that is not subject to an Acid Rain emissions... designated representative of a CAIR NOX Ozone Season unit that is subject to an Acid Rain emissions...

40 CFR 96.375 - Petitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... designated representative of a CAIR NOX Ozone Season unit that is subject to an Acid Rain emissions... designated representative of a CAIR NOX Ozone Season unit that is not subject to an Acid Rain emissions... designated representative of a CAIR NOX Ozone Season unit that is subject to an Acid Rain emissions...

Why do Models Overestimate Surface Ozone in the Southeastern United States?

NASA Technical Reports Server (NTRS)

Travis, Katherine R.; Jacob, Daniel J.; Fisher, Jenny A.; Kim, Patrick S.; Marais, Eloise A.; Zhu, Lei; Yu, Karen; Miller, Christopher C.; Yantosca, Robert M.; Sulprizio, Melissa P.;

Why do models overestimate surface ozone in the Southeast United States?

NASA Astrophysics Data System (ADS)

Travis, Katherine R.; Jacob, Daniel J.; Fisher, Jenny A.; Kim, Patrick S.; Marais, Eloise A.; Zhu, Lei; Yu, Karen; Miller, Christopher C.; Yantosca, Robert M.; Sulprizio, Melissa P.; Thompson, Anne M.; Wennberg, Paul O.; Crounse, John D.; St. Clair, Jason M.; Cohen, Ronald C.; Laughner, Joshua L.; Dibb, Jack E.; Hall, Samuel R.; Ullmann, Kirk; Wolfe, Glenn M.; Pollack, Illana B.; Peischl, Jeff; Neuman, Jonathan A.; Zhou, Xianliang

2016-11-01

Ozone pollution in the Southeast US involves complex chemistry driven by emissions of anthropogenic nitrogen oxide radicals (NOx ≡ NO + NO2) and biogenic isoprene. Model estimates of surface ozone concentrations tend to be biased high in the region and this is of concern for designing effective emission control strategies to meet air quality standards. We use detailed chemical observations from the SEAC4RS aircraft campaign in August and September 2013, interpreted with the GEOS-Chem chemical transport model at 0.25° × 0.3125° horizontal resolution, to better understand the factors controlling surface ozone in the Southeast US. We find that the National Emission Inventory (NEI) for NOx from the US Environmental Protection Agency (EPA) is too high. This finding is based on SEAC4RS observations of NOx and its oxidation products, surface network observations of nitrate wet deposition fluxes, and OMI satellite observations of tropospheric NO2 columns. Our results indicate that NEI NOx emissions from mobile and industrial sources must be reduced by 30-60 %, dependent on the assumption of the contribution by soil NOx emissions. Upper-tropospheric NO2 from lightning makes a large contribution to satellite observations of tropospheric NO2 that must be accounted for when using these data to estimate surface NOx emissions. We find that only half of isoprene oxidation proceeds by the high-NOx pathway to produce ozone; this fraction is only moderately sensitive to changes in NOx emissions because isoprene and NOx emissions are spatially segregated. GEOS-Chem with reduced NOx emissions provides an unbiased simulation of ozone observations from the aircraft and reproduces the observed ozone production efficiency in the boundary layer as derived from a regression of ozone and NOx oxidation products. However, the model is still biased high by 6 ± 14 ppb relative to observed surface ozone in the Southeast US. Ozonesondes launched during midday hours show a 7 ppb ozone decrease from 1.5 km to the surface that GEOS-Chem does not capture. This bias may reflect a combination of excessive vertical mixing and net ozone production in the model boundary layer.

Why do Models Overestimate Surface Ozone in the Southeastern United States?

PubMed Central

Travis, Katherine R.; Jacob, Daniel J.; Fisher, Jenny A.; Kim, Patrick S.; Marais, Eloise A.; Zhu, Lei; Yu, Karen; Miller, Christopher C.; Yantosca, Robert M.; Sulprizio, Melissa P.; Thompson, Anne M.; Wennberg, Paul O.; Crounse, John D.; St Clair, Jason M.; Cohen, Ronald C.; Laughner, Joshua L.; Dibb, Jack E.; Hall, Samuel R.; Ullmann, Kirk; Wolfe, Glenn M.; Pollack, Illana B.; Peischl, Jeff; Neuman, Jonathan A.; Zhou, Xianliang

2018-01-01

Ozone pollution in the Southeast US involves complex chemistry driven by emissions of anthropogenic nitrogen oxide radicals (NOx ≡ NO + NO2) and biogenic isoprene. Model estimates of surface ozone concentrations tend to be biased high in the region and this is of concern for designing effective emission control strategies to meet air quality standards. We use detailed chemical observations from the SEAC4RS aircraft campaign in August and September 2013, interpreted with the GEOS-Chem chemical transport model at 0.25°×0.3125° horizontal resolution, to better understand the factors controlling surface ozone in the Southeast US. We find that the National Emission Inventory (NEI) for NOx from the US Environmental Protection Agency (EPA) is too high. This finding is based on SEAC4RS observations of NOx and its oxidation products, surface network observations of nitrate wet deposition fluxes, and OMI satellite observations of tropospheric NO2 columns. Our results indicate that NEI NOx emissions from mobile and industrial sources must be reduced by 30–60%, dependent on the assumption of the contribution by soil NOx emissions. Upper tropospheric NO2 from lightning makes a large contribution to satellite observations of tropospheric NO2 that must be accounted for when using these data to estimate surface NOx emissions. We find that only half of isoprene oxidation proceeds by the high-NOx pathway to produce ozone; this fraction is only moderately sensitive to changes in NOx emissions because isoprene and NOx emissions are spatially segregated. GEOS-Chem with reduced NOx emissions provides an unbiased simulation of ozone observations from the aircraft, and reproduces the observed ozone production efficiency in the boundary layer as derived from a regression of ozone and NOx oxidation products. However, the model is still biased high by 8±13 ppb relative to observed surface ozone in the Southeast US. Ozonesondes launched during midday hours show a 7 ppb ozone decrease from 1.5 km to the surface that GEOS-Chem does not capture. This bias may reflect a combination of excessive vertical mixing and net ozone production in the model boundary layer. PMID:29619045

Fuel/air nonuniformity - Effect on nitric oxide emissions

NASA Technical Reports Server (NTRS)

Lyons, V. J.

1981-01-01

An analytical and experimental study was performed to determine the effect of inlet fuel/air profile nonuniformity on NO(x) emissions. The theoretical NO(x) levels were verified in a flame-tube rig at inlet air temperatures of 600, 700, and 800 K, 0.3 MPa rig pressure, 25 m/sec reference velocity, overall equivalence ratio of 0.6 and residence time near 0.002 sec. The theory predicts an increase in NO(x) emissions for increased fuel/air nonuniformity for average equivalence ratios less than 0.7, while for average equivalence ratios near stoichiometric, increasing the nonuniformity will decrease NO(x) emissions. The results can be used to predict the degree of uniformity of fuel/air profiles necessary to achieve NO(x) emissions goals for actual engines that use lean premixed, prevaporized combustion systems.

40 CFR 75.71 - Specific provisions for monitoring NOX and heat input for the purpose of calculating NOX mass...

Code of Federal Regulations, 2011 CFR

2011-07-01

... and heat input for the purpose of calculating NOX mass emissions. 75.71 Section 75.71 Protection of... MONITORING NOX Mass Emissions Provisions § 75.71 Specific provisions for monitoring NOX and heat input for... and for a flow monitoring system and an O2 or CO2 diluent gas monitoring system to measure heat input...

Quantifying the isotopic composition of NOx emission sources: An analysis of collection methods

NASA Astrophysics Data System (ADS)

Fibiger, D.; Hastings, M.

2012-04-01

We analyze various collection methods for nitrogen oxides, NOx (NO2 and NO), used to evaluate the nitrogen isotopic composition (δ15N). Atmospheric NOx is a major contributor to acid rain deposition upon its conversion to nitric acid; it also plays a significant role in determining air quality through the production of tropospheric ozone. NOx is released by both anthropogenic (fossil fuel combustion, biomass burning, aircraft emissions) and natural (lightning, biogenic production in soils) sources. Global concentrations of NOx are rising because of increased anthropogenic emissions, while natural source emissions also contribute significantly to the global NOx burden. The contributions of both natural and anthropogenic sources and their considerable variability in space and time make it difficult to attribute local NOx concentrations (and, thus, nitric acid) to a particular source. Several recent studies suggest that variability in the isotopic composition of nitric acid deposition is related to variability in the isotopic signatures of NOx emission sources. Nevertheless, the isotopic composition of most NOx sources has not been thoroughly constrained. Ultimately, the direct capture and quantification of the nitrogen isotopic signatures of NOx sources will allow for the tracing of NOx emissions sources and their impact on environmental quality. Moreover, this will provide a new means by which to verify emissions estimates and atmospheric models. We present laboratory results of methods used for capturing NOx from air into solution. A variety of methods have been used in field studies, but no independent laboratory verification of the efficiencies of these methods has been performed. When analyzing isotopic composition, it is important that NOx be collected quantitatively or the possibility of fractionation must be constrained. We have found that collection efficiency can vary widely under different conditions in the laboratory and fractionation does not vary predictably with collection efficiency. For example, prior measurements frequently utilized triethanolamine solution for collecting NOx, but the collection efficiency was found to drop quickly as the solution aged. The most promising method tested is a NaOH/KMnO4 solution (Margeson and Knoll, Anal. Chem., 1985) which can collect NOx quantitatively from the air. Laboratory tests of previously used methods, along with progress toward creating a suitable and verifiable field deployable collection method will be presented.

Application of OMI Observations to a Space-Based Indicator of NOx and VOC Controls on Surface Ozone Formation

NASA Technical Reports Server (NTRS)

Duncan, Bryan N.; Yoshida, Yasuko; Olson, Jennifer R.; Sillman, Sanford; Martin, Randall V.; Lamsal, Lok; Hu, Yongtao; Pickering, Kenneth E.; Retscher, Christian; Allen, Dale J.;

Technical and environmental performance of 10 kW understocker boiler during combustion of biomass and conventional fuels

NASA Astrophysics Data System (ADS)

Junga, Robert; Wzorek, Małgorzata; Kaszubska, Mirosława

2017-10-01

This paper treats about the impact fuels from biomass wastes and coal combustion on a small boiler operation and the emission of pollutants in this process. Tests were performed in laboratory conditions on a water boiler with retort furnace and the capacity of 10 kW. Fuels from sewage sludge and agriculture wastes (PBZ fuel) and a blend of coal with laying hens mature (CLHM) were taken into account. The results in emission changes of NOx, CO2, CO and SO2 and operating parameters of the tested boiler during combustion were investigated. The obtained results were compared with corresponding results of flame coal (GFC). Combustion of the PBZ fuel turned out to be a stable process in the tested boiler but the thermal output has decreased in about 30% compared to coal combustion, while CO and NOx emission has increased. Similar effect was observed when 15% of the poultry litter was added to the coal. In this case thermal output has also decreased (in about 20%) and increase of CO and NOx emission was observed. As a conclusion, it can be stated that more effective control system with an adaptive air regulation and a modified heat exchanger could be useful in order to achieve the nominal power of the tested boiler.

Plasma-assisted combustion technology for NOx reduction in industrial burners.

PubMed

Lee, Dae Hoon; Kim, Kwan-Tae; Kang, Hee Seok; Song, Young-Hoon; Park, Jae Eon

2013-10-01

Stronger regulations on nitrogen oxide (NOx) production have recently promoted the creation of a diverse array of technologies for NOx reduction, particularly within the combustion process, where reduction is least expensive. In this paper, we discuss a new combustion technology that can reduce NOx emissions within industrial burners to single-digit parts per million levels without employing exhaust gas recirculation or other NOx reduction mechanisms. This new technology uses a simple modification of commercial burners, such that they are able to perform plasma-assisted staged combustion without altering the outer configuration of the commercial reference burner. We embedded the first-stage combustor within the head of the commercial reference burner, where it operated as a reformer that could host a partial oxidation process, producing hydrogen-rich reformate or synthesis gas product. The resulting hydrogen-rich flow then ignited and stabilized the combustion flame apart from the burner rim. Ultimately, the enhanced mixing and removal of hot spots with a widened flame area acted as the main mechanisms of NOx reduction. Because this plasma burner acted as a low NOx burner and was able to reduce NOx by more than half compared to the commercial reference burner, this methodology offers important cost-effective possibilities for NOx reduction in industrial applications.

Modelling the spatial distribution of SO2 and NOx emissions in Ireland.

PubMed

de Kluizenaar, Y; Aherne, J; Farrell, E P

2001-01-01

The spatial distributions of sulphur dioxide (SO2) and nitrogen oxides (NOx) emissions are essential inputs to models of atmospheric transport and deposition. Information of this type is required for international negotiations on emission reduction through the critical load approach. High-resolution emission maps for the Republic of Ireland have been created using emission totals and a geographical information system, supported by surrogate statistics and landcover information. Data have been subsequently allocated to the EMEP 50 x 50-km grid, used in long-range transport models for the investigation of transboundary air pollution. Approximately two-thirds of SO2 emissions in Ireland emanate from two grid-squares. Over 50% of total SO2 emissions originate from one grid-square in the west of Ireland, where the largest point sources of SO2 are located. Approximately 15% of the total SO2 emissions originate from the grid-square containing Dublin. SO2 emission densities for the remaining areas are very low, < 1 t km-2 year-1 for most grid-squares. NOx emissions show a very similar distribution pattern. However, NOx emissions are more evenly spread over the country, as about 40% of total NOx emissions originate from road transport.

Emissions of NO, NO2 and PM from inland shipping

NASA Astrophysics Data System (ADS)

Kurtenbach, Ralf; Vaupel, Kai; Kleffmann, Jörg; Klenk, Ulrich; Schmidt, Eberhard; Wiesen, Peter

2016-11-01

Particulate matter (PM) and nitrogen oxides NOx (NOx = NO2+ NO) are key species for urban air quality in Europe and are emitted by mobile sources. According to European recommendations, a significant fraction of road freight should be shifted to waterborne transport in the future. In order to better consider this emission change pattern in future emission inventories, in the present study inland water transport emissions of NOx, CO2 and PM were investigated under real world conditions on the river Rhine, Germany, in 2013. An average NO2 / NOx emission ratio of 0.08 ± 0.02 was obtained, which is indicative of ship diesel engines without exhaust gas aftertreatment systems. For all measured motor ship types and operation conditions, overall weighted average emission indices (EIs), as emitted mass of pollutant per kg burnt fuel of EINOx = 54 ± 4 g kg-1 and a lower limit EIPM1 ≥ 2.0 ± 0.3 g kg-1, were obtained. EIs for NOx and PM1 were found to be in the range of 20-161 and ≥ 0.2-8.1 g kg-1 respectively. A comparison with threshold values of national German guidelines shows that the NOx emissions of all investigated motor ship types are above the threshold values, while the obtained lower limit PM1 emissions are just under. To reduce NOx emissions to acceptable values, implementation of exhaust gas aftertreatment systems is recommended.

40 CFR 87.64 - Sampling and analytical procedures for measuring gaseous exhaust emissions.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... Round CO2 to the nearest 1 g/kilonewton rO. (c) Report CO2 by calculation from fuel mass flow rate...) [Reserved] (b) Starting January 1, 2011, report CO2 values along with your emission levels of regulated NOX... individual production model was on or after January 1, 2011. By January 1, 2011, report CO2 values along with...

40 CFR 87.64 - Sampling and analytical procedures for measuring gaseous exhaust emissions.

Code of Federal Regulations, 2014 CFR

2014-07-01

.... Round CO2 to the nearest 1 g/kilonewton rO. (c) Report CO2 by calculation from fuel mass flow rate...) [Reserved] (b) Starting January 1, 2011, report CO2 values along with your emission levels of regulated NOX... individual production model was on or after January 1, 2011. By January 1, 2011, report CO2 values along with...

40 CFR 76.7 - Revised NOX emission limitations for Group 1, Phase II boilers.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Revised NOX emission limitations for Group 1, Phase II boilers. 76.7 Section 76.7 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.7 Revised NOX...

40 CFR 96.175 - Petitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... designated representative of a CAIR NOX unit that is subject to an Acid Rain emissions limitation may submit... representative of a CAIR NOX unit that is not subject to an Acid Rain emissions limitation may submit a petition... representative of a CAIR NOX unit that is subject to an Acid Rain emissions limitation may submit a petition...

40 CFR 76.7 - Revised NOX emission limitations for Group 1, Phase II boilers.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 17 2012-07-01 2012-07-01 false Revised NOX emission limitations for Group 1, Phase II boilers. 76.7 Section 76.7 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.7 Revised NOX...

40 CFR 96.175 - Petitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... designated representative of a CAIR NOX unit that is subject to an Acid Rain emissions limitation may submit... representative of a CAIR NOX unit that is not subject to an Acid Rain emissions limitation may submit a petition... representative of a CAIR NOX unit that is subject to an Acid Rain emissions limitation may submit a petition...

40 CFR 76.7 - Revised NOX emission limitations for Group 1, Phase II boilers.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 16 2011-07-01 2011-07-01 false Revised NOX emission limitations for Group 1, Phase II boilers. 76.7 Section 76.7 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.7 Revised NOX...

40 CFR 96.175 - Petitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... designated representative of a CAIR NOX unit that is subject to an Acid Rain emissions limitation may submit... representative of a CAIR NOX unit that is not subject to an Acid Rain emissions limitation may submit a petition... representative of a CAIR NOX unit that is subject to an Acid Rain emissions limitation may submit a petition...

40 CFR 96.175 - Petitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... designated representative of a CAIR NOX unit that is subject to an Acid Rain emissions limitation may submit... representative of a CAIR NOX unit that is not subject to an Acid Rain emissions limitation may submit a petition... representative of a CAIR NOX unit that is subject to an Acid Rain emissions limitation may submit a petition...

40 CFR 76.7 - Revised NOX emission limitations for Group 1, Phase II boilers.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 17 2013-07-01 2013-07-01 false Revised NOX emission limitations for Group 1, Phase II boilers. 76.7 Section 76.7 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.7 Revised NOX...

40 CFR 76.7 - Revised NOX emission limitations for Group 1, Phase II boilers.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 17 2014-07-01 2014-07-01 false Revised NOX emission limitations for Group 1, Phase II boilers. 76.7 Section 76.7 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.7 Revised NOX...

40 CFR 96.175 - Petitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... designated representative of a CAIR NOX unit that is subject to an Acid Rain emissions limitation may submit... representative of a CAIR NOX unit that is not subject to an Acid Rain emissions limitation may submit a petition... representative of a CAIR NOX unit that is subject to an Acid Rain emissions limitation may submit a petition...

40 CFR 75.70 - NOX mass emissions provisions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... subpart to the extent that compliance is required by an applicable State or federal NOX mass emission...) For purposes of this subpart, the term “affected unit” shall mean any unit that is subject to a State...” shall mean the permitting authority under an applicable State or federal NOX mass emission reduction...

Alternative control techniques document: NOx emissions from industrial/commercial/institutional (ICI) boilers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1994-03-01

Industrial, commercial, and institutional (ICI) boilers have been identified as a category that emits more than 25 tons of oxides of nitrogen (NOx) per year. This alternative control techniques (ACT) document provides technical information for use by State and local agencies to develop and implement regulatory programs to control NOx emissions from ICI boilers. Additional ACT documents are being developed for other stationary source categories. Chapter 2 summarizes the findings of this study. Chapter 3 presents information on the ICI boiler types, fuels, operation, and industry applications. Chapter 4 discusses NOx formation and uncontrolled NOx emission factors. Chapter 5 coversmore » alternative control techniques and achievable controlled emission levels. Chapter 6 presents the cost and cost effectiveness of each control technique. Chapter 7 describes environmental and energy impacts associated with implementing the NOx control techniques. Finally, Appendices A through G provide the detailed data used in this study to evaluate uncontrolled and controlled emissions and the costs of controls for several retrofit scenarios.« less

Influence of enhanced Asian NOx emissions on ozone in the upper troposphere and lower stratosphere in chemistry-climate model simulations

NASA Astrophysics Data System (ADS)

Roy, Chaitri; Fadnavis, Suvarna; Müller, Rolf; Ayantika, D. C.; Ploeger, Felix; Rap, Alexandru

2017-01-01

The Asian summer monsoon (ASM) anticyclone is the most pronounced circulation pattern in the upper troposphere and lower stratosphere (UTLS) during northern hemispheric summer. ASM convection plays an important role in efficient vertical transport from the surface to the upper-level anticyclone. In this paper we investigate the potential impact of enhanced anthropogenic nitrogen oxide (NOx) emissions on the distribution of ozone in the UTLS using the fully coupled aerosol-chemistry-climate model, ECHAM5-HAMMOZ. Ozone in the UTLS is influenced both by the convective uplift of ozone precursors and by the uplift of enhanced-NOx-induced tropospheric ozone anomalies. We performed anthropogenic NOx emission sensitivity experiments over India and China. In these simulations, covering the years 2000-2010, anthropogenic NOx emissions have been increased by 38 % over India and by 73 % over China with respect to the emission base year 2000. These emission increases are comparable to the observed linear trends of 3.8 % per year over India and 7.3 % per year over China during the period 2000 to 2010. Enhanced NOx emissions over India by 38 % and China by 73 % increase the ozone radiative forcing in the ASM anticyclone (15-40° N, 60-120° E) by 16.3 and 78.5 mW m-2 respectively. These elevated NOx emissions produce significant warming over the Tibetan Plateau and increase precipitation over India due to a strengthening of the monsoon Hadley circulation. However, increase in NOx emissions over India by 73 % (similar to the observed increase over China) results in large ozone production over the Indo-Gangetic Plain and Tibetan Plateau. The higher ozone concentrations, in turn, induce a reversed monsoon Hadley circulation and negative precipitation anomalies over India. The associated subsidence suppresses vertical transport of NOx and ozone into the ASM anticyclone.

Design and field demonstration of a low-NOx burner for TEOR (thermally enhanced oil recovery) steamers

DOE Office of Scientific and Technical Information (OSTI.GOV)

England, G.C.; Kwan, Y.; Payne, R.

1984-10-01

The paper discusses a program that addresses the need for advanced NOx control technology for thermally enhanced oil recovery (TEOR) steam generators. A full-scale (60 million Btu/hr) burner system has been developed and tested, the concept for which was based on fundamental studies. Test results are included for full-scale burner performance in an experimental test furnace, and in a field-operating steam generator which was subsequently retrofitted in a Kern County, California, oilfield. (NOTE: NOx control techniques including low-NOx burners, postflame NH/sub 3/ injection, or other postflame treatment methods--e.g., selective catalytic reduction--have been considered in order to comply with regulations. Themore » level of NOx control required to meet both growth and air quality goals has typically been difficult to achieve with available technology while maintaining acceptable CO and particulate emissions as well as practical flame conditions within the steamer.)« less

Trend analysis of tropospheric NO2 column density over East Asia during 2000-2010: multi-satellite observations and model simulations with the updated REAS emission inventory

NASA Astrophysics Data System (ADS)

Itahashi, S.; Uno, I.; Irie, H.; Kurokawa, J.; Ohara, T.

2013-04-01

Satellite observations of the tropospheric NO2 vertical column density (VCD) are closely correlated to surface NOx emissions and can thus be used to estimate the latter. In this study, the NO2 VCDs simulated by a regional chemical transport model with data from the updated Regional Emission inventory in ASia (REAS) version 2.1 were validated by comparison with multi-satellite observations (GOME, SCIAMACHY, GOME-2, and OMI) between 2000 and 2010. Rapid growth in NO2 VCD driven by expansion of anthropogenic NOx emissions was revealed above the central eastern China region, except during the economic downturn. In contrast, slightly decreasing trends were captured above Japan. The modeled NO2 VCDs using the updated REAS emissions reasonably reproduced the annual trends observed by multi-satellites, suggesting that the NOx emissions growth rate estimated by the updated inventory is robust. On the basis of the close linear relationship of modeled NO2 VCD, observed NO2 VCD, and anthropogenic NOx emissions, the NOx emissions in 2009 and 2010 were estimated. It was estimated that the NOx emissions from anthropogenic sources in China beyond doubled between 2000 and 2010, reflecting the strong growth of anthropogenic emissions in China with the rapid recovery from the economic downturn during late 2008 and mid-2009.

FreedomCAR - Aftertreatment Subsystem Development

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lisa A. Prentiss

2005-09-30

The primary objective of this program was to develop generic aftertreatment technologies applicable for LDV and LDT engines ranging from 55 kW to 200kW, to develop an optimized and integrated aftertreatment system for a LDT (Light Duty Truck) type vehicle, and to demonstrate the technology which will enable light duty diesel engines to meet Federal Tier II regulation with minimum impact on fuel economy. Specifically, the development targets for emissions reduction and fuel injection penalty are given below: (1) NOx conversion efficiency > 90% (hot), > 84% (combined); (2) PM conversion efficiency > 90% (hot), > 84% (combined); (3) Fuelmore » penalty over FTP-75 Less than 5%; and (4) Fuel penalty at Cruise condition Less than 3%. Development of cost-effective, highly efficient diesel exhaust aftertreatment systems in combination with very low engine out emission combustion development are essential elements for realization of Federal Tier II emission standards for Light Duty Trucks and Vehicles. Evaluation of several aftertreatment technologies was completed as part of this program. A combination of Diesel Oxidation Catalyst, NOx Adsorbing Catalyst and Catalyzed Soot Filter was found to provide the levels of conversion efficiency required to achieve the emission targets. While early systems required relatively large catalyst volumes, external dosing, sulfur traps, full bypass configurations and high levels of Platinum metals; the final system is a compact, scalable, flow-through, fully-integrated and engine-managed aftertreatment system capable of commercial application for Light Duty Vehicles and Trucks. NOx adsorber/particulate filter technology is particularly attractive for Light Duty applications due to the lower exhaust flow and temperature requirements as compared to Heavy Duty engines. Despite these strong positive aspects, NOx Adsorbers are challenged by their regeneration requirements and susceptibility to sulfur poisoning and thermal degradation. Capability was developed to regenerate the NOx Adsorber for NOx and SOx as well as the Particulate Filter for soot. This system was fully integrated into a truck and evaluated over the chassis dynamometer for emissions capability and in real-world winter field testing. Durability of the system was evaluated over a variety of accelerated and real-time dynamometer tests. Excellent NOx and PM conversion efficiency was demonstrated, even following 3000 hrs of endurance testing. Unregulated emissions emitted by the system were evaluated as was the fuel penalty associated with the DeNOx and DeSOx regeneration processes. In the final evaluation, the system demonstrated 90% NOx conversion and 99% PM conversion at a 6% fuel penalty over the FTP-75 test cycle. While target fuel penalty levels were demonstrated using full-bypass configuration systems, the cost associated with those systems was prohibitively high and would preclude successful commercialization of the technology. Although the flow-through configuration fell 1% short of the 5% fuel penalty target, the cost of this configuration is such that commercial application is feasible. Cost drivers for the final system configuration were identified and demonstrate areas where future development areas could focus.« less

NOx Emissions from Diesel Passenger Cars Worsen with Age.

PubMed

Chen, Yuche; Borken-Kleefeld, Jens

2016-04-05

Commonly, the NOx emissions rates of diesel vehicles have been assumed to remain stable over the vehicle's lifetime. However, there have been hardly any representative long-term emission measurements. Here we present real-driving emissions of diesel cars and light commercial vehicles sampled on-road over 15 years in Zurich/Switzerland. Results suggest deterioration of NOx unit emissions for Euro 2 and Euro 3 diesel technologies, while Euro 1 and Euro 4 technologies seem to be stable. We can exclude a significant influence of high-emitting vehicles. NOx emissions from all cars and light commercial vehicles in European emission inventories increase by 5-10% accounting for the observed deterioration, depending on the country and its share of diesel cars. We suggest monitoring the stability of emission controls particularly for high-mileage light commercial as well as heavy-duty vehicles.

Impact of Ship Emissions on Marine Boundary Layer NO(x) and SO2 Distributions over the Pacific Basin

NASA Technical Reports Server (NTRS)

Davis, D. D.; Grodzinsky, G.; Kasibhatla, P.; Crawford, J.; Chen, G.; Liu, S.; Bandy, A.; Thornton, D.; Guan, H.; Sandholm, S.

2001-01-01

The impact of ship emissions on marine boundary layer (MBL) NO(x) and SO2 levels over the Pacific Ocean has been explored by comparing predictions (with and without ships) from a global chemical transport model (GCTM) against compiled airborne observations of MBL NO(x) and SO2. For latitudes above 15 N, which define that part of the Pacific having the heaviest shipping, this analysis revealed significant model over prediction for NOx and a modest under prediction for SO2 when ship emissions were considered. Possible reasons for the difference in NO(x) and SO2 were explored using a full-chemistry box model. These results revealed that for an actual plume setting the NO(x) lifetime could be greatly shortened by chemical processes promoted by ship plume emissions themselves. Similar chemical behavior was not found for SO2.

The Sensitivity of U.S. Surface Ozone Formation to NOx, and VOCs as Viewed from Space

NASA Technical Reports Server (NTRS)

Duncan, Bryan N.; Yoshida, Yasuko; Sillman, Sanford; Retscher, Christian; Pickering, Kenneth E.; Martin, Randall V.; Celarier, Edward A.

2009-01-01

We investigated variations in the sensitivity of surface ozone formation in summer to precursor species concentrations of volatile organic compounds (VOCs) and nitrogen oxides (NO(x)) as inferred from the ratio of tropospheric columns of formaldehyde and nitrogen dioxide from the Aura Ozone Monitoring Instrument (OMI). The data indicate that ozone formation became: 1. more sensitive to NO(x) over most of the U.S, from 2005 to 2007 because of substantial decreases in NO(x) emissions primarily from stationary sources, and 2. more sensitive to NO(x) with increasing temperature, in part because emissions of highly reactive, biogenic isoprene increase with temperature, thus increasing the total VOC reactivity. Based on our interpretation of the data, current strategies implemented to reduce unhealthy levels of surface ozone should focus more on reducing NO(x) emissions, except in some downtown areas which have historically benefited from reductions in VOC emissions.

Sensitivities of NOx transformation and the effects on surface ozone and nitrate

NASA Astrophysics Data System (ADS)

Lei, H.; Wang, J. X. L.

2013-08-01

As precursors for tropospheric ozone and nitrate aerosols, Nitrogen oxides (NOx) in present atmosphere and its transformation in responding to emission and climate perturbations are studied by CAM-Chem model and air quality measurements including National Emission Inventory (NEI), Clean Air Status and Trends Network (CASTNET) and Environmental Protection Agency Air Quality System (EPA AQS). It is found that not only the surface ozone formation but also the nitrate formation is associated with the relative emissions of NOx and volatile organic compounds (VOC). Due to the availability of VOC and associated NOx titration, ozone productions in industrial regions increase in warmer conditions and slightly decrease against NOx emission increase, which is converse to the response in farming region. The decrease or small increase in ozone concentrations over industrial regions result in the responded nitrate increasing rate staying above the increasing rate of NOx emissions. It is indicated that ozone concentration change is more directly affected by changes in climate and precursor emissions, while nitrate concentration change is also affected by local ozone production types and their seasonal transfer. The sensitivity to temperature perturbations shows that warmer climate accelerates the decomposition of odd nitrogen (NOy) during the night. As a result, the transformation rate of NOx to nitrate decreases. Examinations on the historical emission and air quality records on typical pollution areas further confirm the conclusion drawn from modeling experiments.

Emission Characteristics of Gas-Fired Boilers based on Category-Specific Emission Factor from Field Measurements in Beijing, China

NASA Astrophysics Data System (ADS)

Itahashi, S.; Yan, X.; Song, G.; Yan, J.; Xue, Y.

2017-12-01

Gas-fired boilers will become the main stationary sources of NOx in Beijing. However, the knowledge of gas-fired boilers in Beijing is limited. In the present study, the emission characteristics of NOx, SO2, and CO from gas-fired boilers in Beijing were established using category-specific emission factors (EFs) from field measurements. In order to obtain category-specific EFs, boilers were classified through influence analysis. Factors such as combustion mode, boiler type, and installed capacity were considered critical for establishing EFs because they play significant roles in pollutant formation. The EFs for NOx, CO, and SO2 ranged from 1.42-6.86 g m-3, 0.05-0.67 g m-3 and 0.03-0.48 g m-3. The emissions of NOx, SO2, and CO for gas-fired boilers in Beijing were 11121 t, 468 t, and 222 t in 2014, respectively. The emissions were spatially allocated into grid cells with a resolution of 1 km × 1 km, and the results indicated that top emitters were in central Beijing. The uncertainties were quantified using a Monte Carlo simulation. The results indicated high uncertainties in CO (-157% to 154%) and SO2 (-127% to 182%) emissions, and relatively low uncertainties (-34% to 34%) in NOx emission. Furthermore, approximately 61.2% and 96.8% of the monitored chamber combustion boilers (CCBs) met the standard limits for NOx and SO2, respectively. Concerning NOx, low-NOx burners and NOx emission control measures are urgently needed for implementing of stricter standards. Adopting terminal control measures is unnecessary for SO2, although its concentration occasionally exceeds standard limits, because reduction of its concentration can be achieved thorough control of the sulfur content of natural gas at a stable low level. Furthermore, the atmospheric combustion boilers (ACBs) should be substituted with CCBs, because ACBs have a higher emission despite lower gross installed capacity. The results of this study will enable in understanding and controlling emissions from gas-fired boilers in Beijing.

Correlating Engine NOx Emission with Biodiesel Composition

NASA Astrophysics Data System (ADS)

Jeyaseelan, Thangaraja; Mehta, Pramod Shankar

2017-06-01

Biodiesel composition comprising of saturated and unsaturated fatty acid methyl esters has a significant influence on its properties and hence the engine performance and emission characteristics. This paper proposes a comprehensive approach for composition-property-NOx emission analysis for biodiesel fuels and highlights the pathways responsible for such a relationship. Finally, a procedure and a predictor equation are developed for the assessment of biodiesel NOx emission from its composition details.

Using air quality modeling to study source-receptor relationships between nitrogen oxides emissions and ozone exposures over the United States.

PubMed

Tong, Daniel Q; Muller, Nicholas Z; Kan, Haidong; Mendelsohn, Robert O

2009-11-01

Human exposure to ambient ozone (O(3)) has been linked to a variety of adverse health effects. The ozone level at a location is contributed by local production, regional transport, and background ozone. This study combines detailed emission inventory, air quality modeling, and census data to investigate the source-receptor relationships between nitrogen oxides (NO(x)) emissions and population exposure to ambient O(3) in 48 states over the continental United States. By removing NO(x) emissions from each state one at a time, we calculate the change in O(3) exposures by examining the difference between the base and the sensitivity simulations. Based on the 49 simulations, we construct state-level and census region-level source-receptor matrices describing the relationships among these states/regions. We find that, for 43 receptor states, cumulative NO(x) emissions from upwind states contribute more to O(3) exposures than the state's own emissions. In-state emissions are responsible for less than 15% of O(3) exposures in 90% of U.S. states. A state's NO(x) emissions can influence 2 to 40 downwind states by at least a 0.1 ppbv change in population-averaged O(3) exposure. The results suggest that the U.S. generally needs a regional strategy to effectively reduce O(3) exposures. But the current regional emission control program in the U.S. is a cap-and-trade program that assumes the marginal damage of every ton of NO(x) is equal. In this study, the average O(3) exposures caused by one ton of NO(x) emissions ranges from -2.0 to 2.3 ppm-people-hours depending on the state. The actual damage caused by one ton of NO(x) emissions varies considerably over space.

Evaluation of life-cycle air emission factors of freight transportation.

PubMed

Facanha, Cristiano; Horvath, Arpad

2007-10-15

Life-cycle air emission factors associated with road, rail, and air transportation of freight in the United States are analyzed. All life-cycle phases of vehicles, infrastructure, and fuels are accounted for in a hybrid life-cycle assessment (LCA). It includes not only fuel combustion, but also emissions from vehicle manufacturing, maintenance, and end of life, infrastructure construction, operation, maintenance, and end of life, and petroleum exploration, refining, and fuel distribution. Results indicate that total life-cycle emissions of freight transportation modes are underestimated if only tailpipe emissions are accounted for. In the case of CO2 and NOx, tailpipe emissions underestimate total emissions by up to 38%, depending on the mode. Total life-cycle emissions of CO and SO2 are up to seven times higher than tailpipe emissions. Sensitivity analysis considers the effects of vehicle type, geography, and mode efficiency on the final results. Policy implications of this analysis are also discussed. For example, while it is widely assumed that currently proposed regulations will result in substantial reductions in emissions, we find that this is true for NOx, emissions, because fuel combustion is the main cause, and to a lesser extent for SO2, but not for PM10 emissions, which are significantly affected by the other life-cycle phases.

NOx emission trends over Chinese cities estimated from OMI observations during 2005 to 2015

NASA Astrophysics Data System (ADS)

Liu, Fei; Beirle, Steffen; Zhang, Qiang; van der A, Ronald J.; Zheng, Bo; Tong, Dan; He, Kebin

2017-08-01

Satellite nitrogen dioxide (NO2) observations have been widely used to evaluate emission changes. To determine trends in nitrogen oxides (NOx) emission over China, we used a method independent of chemical transport models to quantify the NOx emissions from 48 cities and seven power plants over China, on the basis of Ozone Monitoring Instrument (OMI) NO2 observations from 2005 to 2015. We found that NOx emissions over 48 Chinese cities increased by 52 % from 2005 to 2011 and decreased by 21 % from 2011 to 2015. The decrease since 2011 could be mainly attributed to emission control measures in power sector; while cities with different dominant emission sources (i.e., power, industrial, and transportation sectors) showed variable emission decline timelines that corresponded to the schedules for emission control in different sectors. The time series of the derived NOx emissions was consistent with the bottom-up emission inventories for all power plants (r = 0. 8 on average), but not for some cities (r = 0. 4 on average). The lack of consistency observed for cities was most probably due to the high uncertainty of bottom-up urban emissions used in this study, which were derived from downscaling the regional-based emission data to city level by using spatial distribution proxies.

40 CFR 96.374 - Recordkeeping and reporting.

Code of Federal Regulations, 2010 CFR

2010-07-01

... entire year and shall report the NOX mass emissions data and heat input data for such unit, in an... monitoring of NOX mass emissions) for such unit for the entire year and report the NOX mass emissions data and heat input data for such unit in accordance with paragraph (d)(1) of this section; or (ii) Meet...

Idle emissions from heavy-duty diesel and natural gas vehicles at high altitude.

PubMed

McCormick, R L; Graboski, M S; Alleman, T L; Yanowitz, J

2000-11-01

Idle emissions of total hydrocarbon (THC), CO, NOx, and particulate matter (PM) were measured from 24 heavy-duty diesel-fueled (12 trucks and 12 buses) and 4 heavy-duty compressed natural gas (CNG)-fueled vehicles. The volatile organic fraction (VOF) of PM and aldehyde emissions were also measured for many of the diesel vehicles. Experiments were conducted at 1609 m above sea level using a full exhaust flow dilution tunnel method identical to that used for heavy-duty engine Federal Test Procedure (FTP) testing. Diesel trucks averaged 0.170 g/min THC, 1.183 g/min CO, 1.416 g/min NOx, and 0.030 g/min PM. Diesel buses averaged 0.137 g/min THC, 1.326 g/min CO, 2.015 g/min NOx, and 0.048 g/min PM. Results are compared to idle emission factors from the MOBILE5 and PART5 inventory models. The models significantly (45-75%) overestimate emissions of THC and CO in comparison with results measured from the fleet of vehicles examined in this study. Measured NOx emissions were significantly higher (30-100%) than model predictions. For the pre-1999 (pre-consent decree) truck engines examined in this study, idle NOx emissions increased with model year with a linear fit (r2 = 0.6). PART5 nationwide fleet average emissions are within 1 order of magnitude of emissions for the group of vehicles tested in this study. Aldehyde emissions for bus idling averaged 6 mg/min. The VOF averaged 19% of total PM for buses and 49% for trucks. CNG vehicle idle emissions averaged 1.435 g/min for THC, 1.119 g/min for CO, 0.267 g/min for NOx, and 0.003 g/min for PM. The g/min PM emissions are only a small fraction of g/min PM emissions during vehicle driving. However, idle emissions of NOx, CO, and THC are significant in comparison with driving emissions.

LOW-CONCENTRATION NOX EMISSIONS MEASUREMENT

EPA Science Inventory

The paper gives results of a recent series of low-concentration nitrogen oxides (NOx) emission measurements, made by Midwest Research Institute (MRI) during U.S. EPA-sponsored Environmental Technology Verification (ETV) test of a NOx control system called Xonon (TM) Cool Combust...

NOx reduction in catalytically stabilized thermal burners. Annual report, pril 1, 1988-March 31, 1989

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pfefferle, L.D.

1989-09-01

Catalytically stabilized combustors can be designed to combine the high reaction rates of thermal combustors with low-NOx emissions. The objectives of the research are to understand why the CST burner has inherently low-NOx emissions and whether preexisting NOx can be reduced in-situ in the post-flame zone of a CST burner. Initial results indicate that reduced NOx emissions are, at least for some operating conditions, due to more than just the ability to stabilize combustion at low temperatures. The next phase of the investigation will focus on isothermal flow-tube kinetics studies to isolate catalytic and thermal effects.

Variability in Light-Duty Gasoline Vehicle Emission Factors from Trip-Based Real-World Measurements.

PubMed

Liu, Bin; Frey, H Christopher

2015-10-20

Using data obtained with portable emissions measurements systems (PEMS) on multiple routes for 100 gasoline vehicles, including passenger cars (PCs), passenger trucks (PTs), and hybrid electric vehicles (HEVs), variability in tailpipe emission rates was evaluated. Tier 2 emission standards are shown to be effective in lowering NOx, CO, and HC emission rates. Although PTs are larger, heavier vehicles that consume more fuel and produce more CO2 emissions, they do not necessarily produce more emissions of regulated pollutants compared to PCs. HEVs have very low emission rates compared to tier 2 vehicles under real-world driving. Emission factors vary with cycle average speed and road type, reflecting the combined impact of traffic control and traffic congestion. Compared to the slowest average speed and most congested cycles, optimal emission rates could be 50% lower for CO2, as much as 70% lower for NOx, 40% lower for CO, and 50% lower for HC. There is very high correlation among vehicles when comparing driving cycles. This has implications for how many cycles are needed to conduct comparisons between vehicles, such as when comparing fuels or technologies. Concordance between empirical and predicted emission rates using the U.S. Environmental Protection Agency's MOVES model was also assessed.

Experimental and Modeling Investigation of the Effect of Air Preheat on the Formation of NOx in an RQL Combustor

NASA Technical Reports Server (NTRS)

Samuelsen, G. S.; Brouwer, J.; Vardakas, M. A.; Holderman, J. D.

2012-01-01

The Rich-burn/Quick-mix/Lean-burn (RQL) combustor concept has been proposed to minimize the formation of oxides of nitrogen (NOx) in gas turbine systems. The success of this low-NOx combustor strategy is dependent upon the links between the formation of NOx, inlet air preheat temperature, and the mixing of the jet air and fuel-rich streams. Chemical equilibrium and kinetics modeling calculations and experiments were performed to further understand NOx emissions in an RQL combustor. The results indicate that as the temperature at the inlet to the mixing zone increases (due to preheating and/or operating conditions) the fuel-rich zone equivalence ratio must be increased to achieve minimum NOx formation in the primary zone of the combustor. The chemical kinetics model illustrates that there is sufficient residence time to produce NOx at concentrations that agree well with the NOx measurements. Air preheat was found to have very little effect on mixing, but preheating the air did increase NOx emissions significantly. By understanding the mechanisms governing NOx formation and the temperature dependence of key reactions in the RQL combustor, a strategy can be devised to further reduce NOx emissions using the RQL concept.

Estimating PM2.5-associated mortality increase in California due to the Volkswagen emission control defeat device

NASA Astrophysics Data System (ADS)

Wang, Tianyang; Jerrett, Michael; Sinsheimer, Peter; Zhu, Yifang

2016-11-01

The Volkswagen Group of America (VW) was found by the US Environmental Protection Agency (EPA) and the California Air Resources Board (CARB) to have installed "defeat devices" and emit more oxides of nitrogen (NOx) than permitted under current EPA standards. In this paper, we quantify the hidden NOx emissions from this so-called VW scandal and the resulting public health impacts in California. The NOx emissions are calculated based on VW road test data and the CARB Emission Factors (EMFAC) model. Cumulative hidden NOx emissions from 2009 to 2015 were estimated to be over 3500 tons. Adult mortality changes were estimated based on ambient fine particulate matter (PM2.5) change due to secondary nitrate formation and the related concentration-response functions. We estimated that hidden NOx emissions from 2009 to 2015 have resulted in a total of 12 PM2.5-associated adult mortality increases in California. Most of the mortality increase happened in metropolitan areas, due to their high population and vehicle density.

40 CFR 76.6 - NOX emission limitations for Group 2 boilers.

Code of Federal Regulations, 2010 CFR

2010-07-01

... PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.6 NOX emission limitations..., the date on which the unit is required to meet Acid Rain emission reduction requirements for SO2, the...

40 CFR 76.6 - NOX emission limitations for Group 2 boilers.

Code of Federal Regulations, 2014 CFR

2014-07-01

... PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.6 NOX emission limitations..., the date on which the unit is required to meet Acid Rain emission reduction requirements for SO2, the...

40 CFR 76.6 - NOX emission limitations for Group 2 boilers.

Code of Federal Regulations, 2011 CFR

2011-07-01

... PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.6 NOX emission limitations..., the date on which the unit is required to meet Acid Rain emission reduction requirements for SO2, the...

40 CFR 76.6 - NOX emission limitations for Group 2 boilers.

Code of Federal Regulations, 2013 CFR

2013-07-01

... PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.6 NOX emission limitations..., the date on which the unit is required to meet Acid Rain emission reduction requirements for SO2, the...

40 CFR 76.6 - NOX emission limitations for Group 2 boilers.

Code of Federal Regulations, 2012 CFR

2012-07-01

... PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.6 NOX emission limitations..., the date on which the unit is required to meet Acid Rain emission reduction requirements for SO2, the...

Modeling the weekly cycle of NOx and CO emissions and their impacts on O3 in the Los Angeles-South Coast Air Basin during the CalNex 2010 field campaign

NASA Astrophysics Data System (ADS)

Kim, S.-W.; McDonald, B. C.; Baidar, S.; Brown, S. S.; Dube, B.; Ferrare, R. A.; Frost, G. J.; Harley, R. A.; Holloway, J. S.; Lee, H.-J.; McKeen, S. A.; Neuman, J. A.; Nowak, J. B.; Oetjen, H.; Ortega, I.; Pollack, I. B.; Roberts, J. M.; Ryerson, T. B.; Scarino, A. J.; Senff, C. J.; Thalman, R.; Trainer, M.; Volkamer, R.; Wagner, N.; Washenfelder, R. A.; Waxman, E.; Young, C. J.

2016-02-01

We developed a new nitrogen oxide (NOx) and carbon monoxide (CO) emission inventory for the Los Angeles-South Coast Air Basin (SoCAB) expanding the Fuel-based Inventory for motor-Vehicle Emissions and applied it in regional chemical transport modeling focused on the California Nexus of Air Quality and Climate Change (CalNex) 2010 field campaign. The weekday NOx emission over the SoCAB in 2010 is 620 t d-1, while the weekend emission is 410 t d-1. The NOx emission decrease on weekends is caused by reduced diesel truck activities. Weekday and weekend CO emissions over this region are similar: 2340 and 2180 t d-1, respectively. Previous studies reported large discrepancies between the airborne observations of NOx and CO mixing ratios and the model simulations for CalNex based on the available bottom-up emission inventories. Utilizing the newly developed emission inventory in this study, the simulated NOx and CO mixing ratios agree with the observations from the airborne and the ground-based in situ and remote sensing instruments during the field study. The simulations also reproduce the weekly cycles of these chemical species. Both the observations and the model simulations indicate that decreased NOx on weekends leads to enhanced photochemistry and increase of O3 and Ox (=O3 + NO2) in the basin. The emission inventory developed in this study can be extended to different years and other urban regions in the U.S. to study the long-term trends in O3 and its precursors with regional chemical transport models.

Promoted decomposition of NOx in automotive diesel-like exhausts by electro-catalytic honeycombs.

PubMed

Huang, Ta-Jen; Chiang, De-Yi; Shih, Chi; Lee, Cheng-Chin; Mao, Chih-Wei; Wang, Bo-Chung

2015-03-17

NO and NO2 (collectively called NOx) are major air pollutants in automotive emissions. More effective and easier treatments of NOx than those achieved by the present methods can offer better protection of human health and higher fuel efficiency that can reduce greenhouse gas emissions. However, currently commercialized technologies for automotive NOx emission control cannot effectively treat diesel-like exhausts with high NOx concentrations. Thus, exhaust gas recirculation (EGR) has been used extensively, which reduces fuel efficiency and increases particulate emission considerably. Our results show that the electro-catalytic honeycomb (ECH) promotes the decomposition of NOx to nitrogen and oxygen, without consuming reagents or other resources. NOx can be converted to nitrogen and oxygen almost completely. The ECHs are shown to effectively remove NOx from gasoline-fueled diesel-like exhausts. A very high NO concentration is preferred in the engine exhaust, especially during engine cold-start. Promoted NOx decomposition (PND) technology for real-world automotive applications is established in this study by using the ECH. With PND, EGR is no longer needed. Diesel-like engines can therefore achieve superior fuel efficiency, and all major automotive pollutants can be easily treated due to high concentration of oxygen in the diesel-like exhausts, leading to zero pollution.

40 CFR 97.71 - Initial certification and recertification procedures.

Code of Federal Regulations, 2013 CFR

2013-07-01

... operator of a NOX Budget unit that is subject to an Acid Rain emissions limitation shall comply with the... section. (b) The owner or operator of a NOX Budget unit that is not subject to an Acid Rain emissions...) of this section. The owner or operator of a NOX Budget unit that is subject to an Acid Rain emissions...

40 CFR 97.71 - Initial certification and recertification procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... operator of a NOX Budget unit that is subject to an Acid Rain emissions limitation shall comply with the... section. (b) The owner or operator of a NOX Budget unit that is not subject to an Acid Rain emissions...) of this section. The owner or operator of a NOX Budget unit that is subject to an Acid Rain emissions...

40 CFR 97.71 - Initial certification and recertification procedures.

Code of Federal Regulations, 2012 CFR

2012-07-01

... operator of a NOX Budget unit that is subject to an Acid Rain emissions limitation shall comply with the... section. (b) The owner or operator of a NOX Budget unit that is not subject to an Acid Rain emissions...) of this section. The owner or operator of a NOX Budget unit that is subject to an Acid Rain emissions...

On the Effects of NOx Emission Control and Drought on an Ozone-Polluted Ecosystem

NASA Astrophysics Data System (ADS)

Pusede, S.; Geddes, J.; Buysse, C. E.; Esperanza, A.; Najacht, E.; Anderson, J. F.; Bailey, C. B.; Munyan, J.

2017-12-01

Regulatory emission controls are typically designed to reduce ozone when ozone is highest. However, high ozone concentrations are often asynchronous with periods of the greatest ozone harm to plants and ecosystems, particularly during drought. Because ozone production chemistry is nonlinear, emissions reductions designed to be effective in polluted cities may have a range of effects on downwind ecosystems. Here, we investigate the influence of regional NOx emission controls on ozone pollution in Sequoia National Park (SNP). First, we show that steep declines in NOx throughout the region have had smaller impacts in SNP than in cities upwind, and that these reductions have been least effective at times of day and year when plants are most sensitive to ozone. Second, in recent years (2012-2015), California experienced the worst drought in recorded history. We present observational evidence of the ozone response in SNP to drought conditions, finding that the drought altered the chemical sensitivity of local ozone production to NOx emissions and, hence, the effectiveness of NOx emission controls. We show that drought impacts on the ozone sensitivity to NOx have persisted at least two years since the drought ended.

Emission Control Technologies for Thermal Power Plants

NASA Astrophysics Data System (ADS)

Nihalani, S. A.; Mishra, Y.; Juremalani, J.

2018-03-01

Coal thermal power plants are one of the primary sources of artificial air emissions, particularly in a country like India. Ministry of Environment and Forests has proposed draft regulation for emission standards in coal-fired power plants. This includes significant reduction in sulphur-dioxide, oxides of nitrogen, particulate matter and mercury emissions. The first step is to evaluate the technologies which represent the best selection for each power plant based on its configuration, fuel properties, performance requirements, and other site-specific factors. This paper will describe various technology options including: Flue Gas Desulfurization System, Spray Dryer Absorber (SDA), Circulating Dry Scrubber (CDS), Limestone-based Wet FGD, Low NOX burners, Selective Non Catalytic Reduction, Electrostatic Precipitator, Bag House Dust Collector, all of which have been evaluated and installed extensively to reduce SO2, NOx, PM and other emissions. Each control technology has its advantages and disadvantages. For each of the technologies considered, major features, potential operating and maintenance cost impacts, as well as key factors that contribute to the selection of one technology over another are discussed here.

Assessing the Public Health Impact of Regional-Scale Air Quality Regulations

EPA Science Inventory

The Clean Air Interstate Rule (CAIR) will further reduce regional emissions of sulfur dioxide (SO2) and nitrogen oxides (NOx), thus reducing fine particulate matter (PM2.5) and ground-level ozone pollution. The U.S. Environmental Protection Agency (EPA) estimates that CAIR will ...

Lightning and anthropogenic NOx sources over the U.S. and the western North Atlantic Ocean: Impact on tropospheric O3 from space-borne observations

NASA Astrophysics Data System (ADS)

Choi, Y.; Eldering, A.; Osterman, G.; Wang, Y.; Cunnold, D.; Yang, Q.; Bucsela, E.; Pickering, K.

2008-12-01

We use the Regional chEmical trAnsport Model (REAM) to analyze the contributions of lightning and anthropogenic NOx on ozone concentrations over the U.S. and the western North Atlantic Ocean from June to August 2005. Tropospheric NO2 columns from OMI, tropospheric O3 columns derived from OMI and MLS measurements, and vertical O3 profiles from TES over the region are used in the analysis. With a 50% reduction in the industrial and electrical power generation NOx emissions in the 23 eastern states over the U.S. from 1999 EPA NEI and a parameterization of lightning-produced NOx based on concurrent NLDN, CAPE, and cloud mass flux data, REAM generally captures the spatial distribution of lightning flash rates and OMI NO2 and OMI-MLS O3 column enhancements with high correlation coefficients (0.6-0.9). The model results show that over the U.S., the contribution of surface NOx emissions to summertime tropospheric O3 declines from 47% to 41% due to the reduced emissions. The contribution of surface NOx emissions becomes similar to that of stratospheric transport over the U.S., with the additional being the dramatic reduction in the relative impact of fossil-fuel NOx emissions over continental outflow regions. In the convective outflow regions over the Gulf of Mexico and the western North Atlantic, the contribution of lightning NOx production on tropospheric O3 in the summer is larger than that of anthropogenic NOx emissions with mean differences of 5% to 25%. The impact of NOx produced by lightning is becoming larger as fossil-fuel combustion NOx emissions decrease. After the onset of the North American monsoon, lightning-derived upper tropospheric O3 enhancements in July and August are shown over the convective outflow regions from REAM simulated and TES measured O3 vertical profiles. This result suggests that TES measurements have a potential to constrain lightning-derived tropospheric O3 enhancements, which may play a critical role in controlling climate.

Changes in inorganic fine particulate matter sensitivities to precursors due to large-scale US emissions reductions.

PubMed

Holt, Jareth; Selin, Noelle E; Solomon, Susan

2015-04-21

We examined the impact of large US emissions changes, similar to those estimated to have occurred between 2005 and 2012 (high and low emissions cases, respectively), on inorganic PM2.5 sensitivities to further NOx, SO2, and NH3 emissions reductions using the chemical transport model GEOS-Chem. Sensitivities to SO2 emissions are larger year-round and across the US in the low emissions case than the high emissions case due to more aqueous-phase SO2 oxidation. Sensitivities to winter NOx emissions are larger in the low emissions case, more than 2× those of the high emissions case in parts of the northern Midwest. Sensitivities to NH3 emissions are smaller (∼40%) in the low emissions case, year-round, and across the US. Differences in NOx and NH3 sensitivities indicate an altered atmospheric acidity. Larger sensitivities to SO2 and NOx in the low emissions case imply that reducing these emissions may improve air quality more now than they would have in 2005; conversely, NH3 reductions may not improve air quality as much as previously assumed.

Effect of B20 and Low Aromatic Diesel on Transit Bus NOx Emissions Over Driving Cycles with a Range of Kinetic Intensity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lammert, M. P.; McCormick, R. L.; Sindler, P.

2012-10-01

Oxides of nitrogen (NOx) emissions for transit buses for up to five different fuels and three standard transit duty cycles were compared to establish whether there is a real-world biodiesel NOx increase for transit bus duty cycles and engine calibrations. Six buses representing the majority of the current national transit fleet and including hybrid and selective catalyst reduction systems were tested on a heavy-duty chassis dynamometer with certification diesel, certification B20 blend, low aromatic (California Air Resources Board) diesel, low aromatic B20 blend, and B100 fuels over the Manhattan, Orange County and UDDS test cycles. Engine emissions certification level hadmore » the dominant effect on NOx; kinetic intensity was the secondary driving factor. The biodiesel effect on NOx emissions was not statistically significant for most buses and duty cycles for blends with certification diesel, except for a 2008 model year bus. CARB fuel had many more instances of a statistically significant effect of reducing NOx. SCR systems proved effective at reducing NOx to near the detection limit on all duty cycles and fuels, including B100. While offering a fuel economy benefit, a hybrid system significantly increased NOx emissions over a same year bus with a conventional drivetrain and the same engine.« less

Modelling NOx emissions of single droplet combustion

NASA Astrophysics Data System (ADS)

Moesl, Klaus G.; Schwing, Joachim E.; Sattelmayer, Thomas

2012-02-01

An approach for modelling and simulation of the generation of nitrogen oxide (NOx) in the gas phase surrounding single burning droplets is presented. Assuming spherical symmetry (no gravity, no forced convection), the governing equations are derived first. Then simplifications are introduced and it is proven that they are appropriate. The influences of the initial droplet diameter, the ambient conditions, and the droplet pre-vapourisation on NOx are investigated. The fuel of choice is n-decane (C10H22) as it resembles kerosene and diesel fuel best, and the complexity of the reaction mechanism is manageable. Combinations of C10H22 mechanisms and well-established NOx kinetics are evaluated in detail and validated for their applicability in the context of this work. The conducted simulations of droplet combustion in an atmosphere of hot exhaust gas show that NOx formation (by mass of fuel) increases linearly with the droplet diameter. There is a trade-off between available oxygen and ambient temperature. Increasing the equivalence ratio of the exhaust gas leads to higher NOx emissions in the very lean regime, but to lower emissions if the equivalence ratio exceeds 0.85. Pre-vapourisation of fuel at ambient conditions becomes beneficial with respect to NOx emissions only if the degree of vapourisation is above a minimum limit. If less fuel is vapourised before ignition, the NOx emissions remain almost unaffected.

Traffic-related air quality trends in São Paulo, Brazil

NASA Astrophysics Data System (ADS)

Pérez-Martínez, Pedro José; de Fátima Andrade, María.; de Miranda, Regina Maura

2015-06-01

The urban population of South America has grown at 1.05%/yr, greater urbanization increasing problems related to air pollution. In most large cities in South America, there has been no continuous long-term measurement of regulated pollutants. One exception is São Paulo, Brazil, where an air quality monitoring network has been in place since the 1970s. In this paper, we used an air quality-based approach to determine pollutant trends for emissions of carbon monoxide (CO), nitrogen oxides (NOx), ozone (O3), and coarse particulate matter (PM10), mostly from mobile sources, in the Metropolitan Region of São Paulo for the 2000-2013 period. Mobile sources included light-duty vehicles (LDVs, comprising gasoline- or ethanol-powered cars and motorcycles) and heavy-duty vehicles (HDVs, comprising diesel-powered trucks and buses). Pollutant concentrations for mobile source emissions were measured and correlated with fuel sales by the emission factors. Over the 2000-2013 period, concentrations of NOx, CO, and PM10 decreased by 0.65, 0.37, and 0.71% month-1, respectively, whereas sales of gasoline, ethanol, and diesel increased by 0.26, 1.96, and 0.38% month-1, respectively. LDVs were the major mobile source of CO, whereas LDVs were the major source of NOx and PM10. Increases in fuel sales and in the corresponding traffic volume were partially offset by decreases in pollutant concentrations. Between 2000 and 2013, there was a sharp (-5 ppb month-1) decrease in the concentrations of LDV-emitted CO, together with (less dramatic) decreases in the concentrations of HDV-emitted NOx and PM10 (-0.25 and -0.09 ppb month-1, respectively). Variability was greater for HDV-emitted NOx and PM10 (R = -0.47 and -0.41, respectively) than for LDV-emitted CO (R = -0.72). We draw the following conclusions: the observed concentrations of LDV-emitted CO decreased at a sharper rate than did those of HDV-emitted NOx and PM10; mobile source contributions to O3 formation varied significantly, LDVs making a greater contribution during the 2000-2008 period, whereas HDVs made a greater contribution during the 2009-2013 period, and decreases in NOx emissions resulted in increases in O3 observations.

Evaluation of Space-Based Constraints on Global Nitrogen Oxide Emissions with Regional Aircraft Measurements over and Downwind of Eastern North America

NASA Technical Reports Server (NTRS)

Martin, Randall V.; Sioris, Christopher E.; Chance, Kelly; Ryerson, Thomas B.; Flocke, Frank M.; Bertram, Timothy H.; Wooldridge, Paul J.; Cohen, Ronald C.; Neuman, J. Andy; Swanson, Aaron

2006-01-01

We retrieve tropospheric nitrogen dioxide (NO 2) columns for May 2004 to April 2005 from the SCIAMACHY satellite instrument to derive top-down emissions of nitrogen oxides (NO(x) = NO + NO2) via inverse modeling with a global chemical transport model (GEOS-Chem). Simulated NO 2 vertical profiles used in the retrieval are evaluated with airborne measurements over and downwind of North America (ICARTT); a northern midlatitude lightning source of 1.6 Tg N/yr minimizes bias in the retrieval. Retrieved NO2 columns are validated (r2 = 0.60, slope = 0.82) with coincident airborne in situ measurements. The top-down emissions are combined with a priori information from a bottom-up emission inventory with error weighting to achieve an improved a posteriori estimate of the global distribution of surface NOx emissions. Our a posteriori NOx emission inventory for land surface NOx emissions (46.1 Tg N/yr) is 22% larger than the GEIA-based a priori bottom-up inventory for 1998, a difference that reflects rising anthropogenic emissions, especially from East Asia A posteriori NOx emissions for East Asia (9.8 Tg N/yr) exceed those from other continents. The a posteriori inventory improves the GEOS-Chem simulation of NOx, peroxyacetylnitrate, and nitric acid with respect to airborne in situ measurements over and downwind of New York City. The a posteriori is 7% larger than the EDGAR 3.2FT2000 global inventory, 3% larger than the NEI99 inventory for the United States, and 68% larger than a regional inventory for 2000 for eastern Asia. SCIAMACHY NO2 columns over the North Atlantic show a weak plume from lightning NO(x).

Impact of biodiesel source material and chemical structure on emissions of criteria pollutants from a heavy-duty engine.

PubMed

McCormick, R L; Graboski, M S; Alleman, T L; Herring, A M; Tyson, K S

2001-05-01

Biodiesel is an oxygenated diesel fuel made from vegetable oils and animal fats by conversion of the triglyceride fats to esters via transesterification. In this study we examined biodiesels produced from a variety of real-world feedstocks as well as pure (technical grade) fatty acid methyl and ethyl esters for emissions performance in a heavy-duty truck engine. The objective was to understand the impact of biodiesel chemical structure, specifically fatty acid chain length and number of double bonds, on emissions of NOx and particulate matter (PM). A group of seven biodiesels produced from real-world feedstocks and 14 produced from pure fatty acids were tested in a heavy-duty truck engine using the U.S. heavy-duty federal test procedure (transient test). It was found that the molecular structure of biodiesel can have a substantial impact on emissions. The properties of density, cetane number, and iodine number were found to be highly correlated with one another. For neat biodiesels, PM emissions were essentially constant at about 0.07 g/bhp-h for all biodiesels as long as density was less than 0.89 g/cm3 or cetane number was greater than about 45. NOx emissions increased with increasing fuel density or decreasing fuel cetane number. Increasing the number of double bonds, quantified as iodine number, correlated with increasing emissions of NOx. Thus the increased NOx observed for some fuels cannot be explained by the NOx/PM tradeoff and is therefore not driven by thermal NO formation. For fully saturated fatty acid chains the NOx emission increased with decreasing chain length for tests using 18, 16, and 12 carbon chain molecules. Additionally, there was no significant difference in NOx or PM emissions for the methyl and ethyl esters of identical fatty acids.

Meteorological detrending of primary and secondary pollutant concentrations: Method application and evaluation using long-term (2000-2012) data in Atlanta

NASA Astrophysics Data System (ADS)

Henneman, Lucas R. F.; Holmes, Heather A.; Mulholland, James A.; Russell, Armistead G.

2015-10-01

The effectiveness of air pollution regulations and controls are evaluated based on measured air pollutant concentrations. Air pollution levels, however, are highly sensitive to both emissions and meteorological fluctuations. Therefore, an assessment of the change in air pollutant levels due to emissions controls must account for these meteorological fluctuations. Two empirical methods to quantify the impact of meteorology on pollutant levels are discussed and applied to the 13-year time period between 2000 and 2012 in Atlanta, GA. The methods employ Kolmogorov-Zurbenko filters and linear regressions to detrended pollutant signals into long-term, seasonal, weekly, short-term, and white-noise components. The methods differ in how changes in weekly and holiday emissions are accounted for. Both can provide meteorological adjustments on a daily basis for future use in acute health analyses. The meteorological impact on daily signals of ozone, NOx, CO, SO2, PM2.5, and PM species are quantified. Analyses show that the substantial decreases in seasonal averages of NOx and SO2 correspond with controls implemented in the metropolitan Atlanta area. Detrending allows for the impacts of some controls to be observed with averaging times of as little as 3 months. Annual average concentrations of NOx, SO2, and CO have all fallen by at least 50% since 2000. Reductions in NOx levels, however, do not lead to uniform reductions in ozone. While average detrended summer average maximum daily average 8 h ozone (MDA8h O3) levels fell by 4% (2.2 ± 2 ppb) between 2000 and 2012, winter averages have increased by 12% (3.8 ± 1.4 ppb), providing further evidence that high ozone levels are NOx-limited and lower ozone concentrations are NOx-inhibited. High ozone days (with MDA8h O3 greater than 60 ppb) decreased both in number and in magnitude over the study period.

Emission characteristics of NOx, CO, NH3 and VOCs from gas-fired industrial boilers based on field measurements in Beijing city, China

NASA Astrophysics Data System (ADS)

Yue, Tao; Gao, Xiang; Gao, Jiajia; Tong, Yali; Wang, Kun; Zuo, Penglai; Zhang, Xiaoxi; Tong, Li; Wang, Chenlong; Xue, Yifeng

2018-07-01

In the past decade, due to the management policies and coal combustion controls in Beijing, the consumption of natural gas has increased gradually. Nevertheless, the research on the emission characteristics of gaseous pollutants emitted from gas-fired industrial boilers, especially considering the influence of low nitrogen (low-NOx) retrofit policy of gas boilers, is scarcely. In this study, based on literature and field investigations, onsite measurements of NOx, CO, NH3 and VOCs (Volatile Organic Compounds) emissions from gas-fired industrial boilers as well as the key factors that affected the emission of gaseous pollutants were discussed. Category-specific emission factors (EFs) of NOx, CO, NH3 and VOCs were obtained from the field measurements of 1107 "low-NOx" retrofitted and unabated gas-fired industrial boilers. Our results showed that operating load and control measures were the two key factors affecting the formation of gaseous pollutants. The EFs of NOx (EFNOx) and CO (EFCO) of atmospheric combustion boilers (ACBs) were much higher than the EFs of chamber combustion boilers (CCBs). The total emissions of NOx, CO, NH3 and VOCs from gas-fired industrial boilers in Beijing in the year of 2015 were estimated at 10489.6 t, 3272.8 t, 196.4 t and 235.4 t, respectively. Alkanes, BTEX, oxygenated VOCs and non-reactive organic matter were the four main chemical components of VOCs. As for the spatial distributions, the emissions of NOx, CO, NH3 and VOCs from gas-fired industrial boilers in Beijing were predominantly concentrated in central six urban districts. In the future, more detailed investigation and field tests for all kinds of gas-fired industrial boilers are still greatly needed to achieve more reliable estimations of atmospheric pollutants from gas-fired industrial boilers.

THE ACID RAIN NOX PROGRAM

EPA Science Inventory

Between 350,000 and 400,000 tons of annual NOx emissions have been eliminated as a result of Phase I of the Acid Rain NOx Program. As expected. the utilities have chosen emissions averaging as the primary compliance option. This reflects that, in general, NO x reductions have ...

Spatially resolved flux measurements of NOx from London suggest significantly higher emissions than predicted by inventories.

PubMed

Vaughan, Adam R; Lee, James D; Misztal, Pawel K; Metzger, Stefan; Shaw, Marvin D; Lewis, Alastair C; Purvis, Ruth M; Carslaw, David C; Goldstein, Allen H; Hewitt, C Nicholas; Davison, Brian; Beevers, Sean D; Karl, Thomas G

2016-07-18

To date, direct validation of city-wide emissions inventories for air pollutants has been difficult or impossible. However, recent technological innovations now allow direct measurement of pollutant fluxes from cities, for comparison with emissions inventories, which are themselves commonly used for prediction of current and future air quality and to help guide abatement strategies. Fluxes of NOx were measured using the eddy-covariance technique from an aircraft flying at low altitude over London. The highest fluxes were observed over central London, with lower fluxes measured in suburban areas. A footprint model was used to estimate the spatial area from which the measured emissions occurred. This allowed comparison of the flux measurements to the UK's National Atmospheric Emissions Inventory (NAEI) for NOx, with scaling factors used to account for the actual time of day, day of week and month of year of the measurement. The comparison suggests significant underestimation of NOx emissions in London by the NAEI, mainly due to its under-representation of real world road traffic emissions. A comparison was also carried out with an enhanced version of the inventory using real world driving emission factors and road measurement data taken from the London Atmospheric Emissions Inventory (LAEI). The measurement to inventory agreement was substantially improved using the enhanced version, showing the importance of fully accounting for road traffic, which is the dominant NOx emission source in London. In central London there was still an underestimation by the inventory of 30-40% compared with flux measurements, suggesting significant improvements are still required in the NOx emissions inventory.

Estimating Lightning NOx Emissions for Regional Air Quality Modeling

NASA Astrophysics Data System (ADS)

Holloway, T.; Scotty, E.; Harkey, M.

2014-12-01

Lightning emissions have long been recognized as an important source of nitrogen oxides (NOx) on a global scale, and an essential emission component for global atmospheric chemistry models. However, only in recent years have regional air quality models incorporated lightning NOx emissions into simulations. The growth in regional modeling of lightning emissions has been driven in part by comparisons with satellite-derived estimates of column NO2, especially from the Ozone Monitoring Instrument (OMI) aboard the Aura satellite. We present and evaluate a lightning inventory for the EPA Community Multiscale Air Quality (CMAQ) model. Our approach follows Koo et al. [2010] in the approach to spatially and temporally allocating a given total value based on cloud-top height and convective precipitation. However, we consider alternate total NOx emission values (which translate into alternate lightning emission factors) based on a review of the literature and performance evaluation against OMI NO2 for July 2007 conditions over the U.S. and parts of Canada and Mexico. The vertical distribution of lightning emissions follow a bimodal distribution from Allen et al. [2012] calculated over 27 vertical model layers. Total lightning NO emissions for July 2007 show the highest above-land emissions in Florida, southeastern Texas and southern Louisiana. Although agreement with OMI NO2 across the domain varied significantly depending on lightning NOx assumptions, agreement among the simulations at ground-based NO2 monitors from the EPA Air Quality System database showed no meaningful sensitivity to lightning NOx. Emissions are compared with prior studies, which find similar distribution patterns, but a wide range of calculated magnitudes.

The effect of water injection on nitric oxide emissions of a gas turbine combustor burning ASTM Jet-A fuel

NASA Technical Reports Server (NTRS)

Marchionna, N. R.; Diehl, L. A.; Trout, A. M.

1973-01-01

Tests were conducted to determine the effect of water injection on oxides of nitrogen (NOx) emissions of a full annular, ram induction gas turbine combustor burning ASTM Jet-A fuel. The combustor was operated at conditions simulating sea-level takeoff and cruise conditions. Water at ambient temperature was injected into the combustor primary zone at water-fuel ratios up to 2. At an inlet-air temperature of 589 K (600 F) water injection decreased the NOx emission index at a constant exponential rate: NOx = NOx (o) e to the -15 W/F power (where W/F is the water-fuel ratio and NOx(o) indicates the value with no injection). The effect of increasing combustor inlet-air temperature was to decrease the effect of the water injection. Other operating variables such as pressure and reference Mach number did not appear to significantly affect the percent reduction in NOx. Smoke emissions were found to decrease with increasing water injection.

Emission Characteristics of A P and W Axially Staged Sector Combustor

NASA Technical Reports Server (NTRS)

He, Zhuohui J.; Wey, Changlie; Chang, Clarence T.; Lee, Chi Ming; Surgenor, Angela D.; Kopp-Vaughan, Kristin; Cheung, Albert

2016-01-01

Emission characteristics of a three-cup P and W Axially Controlled Stoichiometry (ACS) sector combustor are reported in this article. Multiple injection points and fuel staging strategies are used in this combustor design. Pilot-stage injectors are located on the front dome plate of the combustor, and main-stage injectors are positioned on the top and bottom of the combustor liners downstream. Low power configuration uses only pilot-stage injectors. Main-stage injectors are added to high power configuration to help distribute fuel more evenly and achieve overall lean burn yielding very low NOx emissions. Combustion efficiencies at four ICAO LTO conditions were all above 99%. Three EINOx emissions correlation equations were developed based on the experimental data to describe the NOx emission trends of this combustor concept. For the 7% and 30% engine power conditions, NOx emissions are obtained with the low power configuration, and the EINOx values are 6.16 and 6.81. The high power configuration was used to assess 85% and 100% engine power NOx emissions, with measured EINOx values of 4.58 and 7.45, respectively. The overall landing-takeoff cycle NOx emissions are about 12% relative to ICAO CAEP/6 level.

Air emissions due to wind and solar power.

PubMed

Katzenstein, Warren; Apt, Jay

2009-01-15

Renewables portfolio standards (RPS) encourage large-scale deployment of wind and solar electric power. Their power output varies rapidly, even when several sites are added together. In many locations, natural gas generators are the lowest cost resource available to compensate for this variability, and must ramp up and down quickly to keep the grid stable, affecting their emissions of NOx and CO2. We model a wind or solar photovoltaic plus gas system using measured 1-min time-resolved emissions and heat rate data from two types of natural gas generators, and power data from four wind plants and one solar plant. Over a wide range of renewable penetration, we find CO2 emissions achieve approximately 80% of the emissions reductions expected if the power fluctuations caused no additional emissions. Using steam injection, gas generators achieve only 30-50% of expected NOx emissions reductions, and with dry control NOx emissions increase substantially. We quantify the interaction between state RPSs and NOx constraints, finding that states with substantial RPSs could see significant upward pressure on NOx permit prices, if the gas turbines we modeled are representative of the plants used to mitigate wind and solar power variability.

Evaluation of mobile source emission trends in the United States

NASA Astrophysics Data System (ADS)

Dallmann, Timothy R.; Harley, Robert A.

2010-07-01

A fuel-based approach is used to estimate exhaust emissions of nitrogen oxides (NOx) and fine particulate matter (PM2.5) from mobile sources in the United States for the years 1996-2006. Source categories considered include on-road and off-road gasoline and diesel engines. Pollutant emissions for each mobile source category were estimated by combining fuel consumption with emission factors expressed per unit of fuel burned. Over the 10-year time period that is the focus of this study, sales of gasoline and diesel fuel intended for on-road use increased by 15 and 43%, respectively. Diesel fuel use by off-road equipment increased by ˜20% over the same time period. Growth in fuel consumption offset some of the reductions in pollutant emission factors that occurred during this period. For NOx, there have been dramatic (factor of 2) decreases in emission factors for on-road gasoline engines between 1996 and 2006. In contrast, diesel NOx emission factors decreased more gradually. Exhaust PM2.5 emission factors appear to have decreased for most engine categories, but emission uncertainties are large for this pollutant. Diesel engines appear to be the dominant mobile source of both NOx and PM2.5; the diesel share of total NOx has increased over time as gasoline engine emissions have declined. Comparing fuel-based emission estimates with U.S. Environmental Protection Agency's national emission inventory led to the following conclusions: (1) total emissions of NOx and PM2.5 estimated by two different methods were similar, (2) source contributions to these totals differ significantly, with higher relative contributions coming from on-road diesel engines in this study.

Lean NOx Trap Catalysis for Lean Natural Gas Engine Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parks, II, James E; Storey, John Morse; Theiss, Timothy J

Distributed energy is an approach for meeting energy needs that has several advantages. Distributed energy improves energy security during natural disasters or terrorist actions, improves transmission grid reliability by reducing grid load, and enhances power quality through voltage support and reactive power. In addition, distributed energy can be efficient since transmission losses are minimized. One prime mover for distributed energy is the natural gas reciprocating engine generator set. Natural gas reciprocating engines are flexible and scalable solutions for many distributed energy needs. The engines can be run continuously or occasionally as peak demand requires, and their operation and maintenance ismore » straightforward. Furthermore, system efficiencies can be maximized when natural gas reciprocating engines are combined with thermal energy recovery for cooling, heating, and power applications. Expansion of natural gas reciprocating engines for distributed energy is dependent on several factors, but two prominent factors are efficiency and emissions. Efficiencies must be high enough to enable low operating costs, and emissions must be low enough to permit significant operation hours, especially in non-attainment areas where emissions are stringently regulated. To address these issues the U.S. Department of Energy and the California Energy Commission launched research and development programs called Advanced Reciprocating Engine Systems (ARES) and Advanced Reciprocating Internal Combustion Engines (ARICE), respectively. Fuel efficiency and low emissions are two primary goals of these programs. The work presented here was funded by the ARES program and, thus, addresses the ARES 2010 goals of 50% thermal efficiency (fuel efficiency) and <0.1 g/bhp-hr emissions of oxides of nitrogen (NOx). A summary of the goals for the ARES program is given in Table 1-1. ARICE 2007 goals are 45% thermal efficiency and <0.015 g/bhp-hr NOx. Several approaches for improving the efficiency and emissions of natural gas reciprocating engines are being pursued. Approaches include: stoichiometric engine operation with exhaust gas recirculation and three-way catalysis, advanced combustion modes such as homogeneous charge compression ignition, and extension of the lean combustion limit with advanced ignition concepts and/or hydrogen mixing. The research presented here addresses the technical approach of combining efficient lean spark-ignited natural gas combustion with low emissions obtained from a lean NOx trap catalyst aftertreatment system. This approach can be applied to current lean engine technology or advanced lean engines that may result from related efforts in lean limit extension. Furthermore, the lean NOx trap technology has synergy with hydrogen-assisted lean limit extension since hydrogen is produced from natural gas during the lean NOx trap catalyst system process. The approach is also applicable to other lean engines such as diesel engines, natural gas turbines, and lean gasoline engines; other research activities have focused on those applications. Some commercialization of the technology has occurred for automotive applications (both diesel and lean gasoline engine vehicles) and natural gas turbines for stationary power. The research here specifically addresses barriers to commercialization of the technology for large lean natural gas reciprocating engines for stationary power. The report presented here is a comprehensive collection of research conducted by Oak Ridge National Laboratory (ORNL) on lean NOx trap catalysis for lean natural gas reciprocating engines. The research was performed in the Department of Energy's ARES program from 2003 to 2007 and covers several aspects of the technology. All studies were conducted at ORNL on a Cummins C8.3G+ natural gas engine chosen based on industry input to simulate large lean natural gas engines. Specific technical areas addressed by the research include: NOx reduction efficiency, partial oxidation and reforming chemistry, and the effects of sulfur poisons on the partial oxidation, reformer, and lean NOx trap catalysts. The initial work on NOx reduction efficiency demonstrated that NOx emissions <0.1 g/bhp-hr (the ARES goal) can be achieved with the lean NOx trap catalyst technology. Subsequent work focused on cost and size optimization and durability issues which addressed two specific ARES areas of interest to industry ('Cost of Power' and 'Availability, Reliability, and Maintainability', respectively). Thus, the research addressed the approach of the lean NOx trap catalyst technology toward the ARES goals as shown in Table 1-1.« less

Climate and environmental effects of electric vehicles versus compressed natural gas vehicles in China: a life-cycle analysis at provincial level.

PubMed

Huo, Hong; Zhang, Qiang; Liu, Fei; He, Kebin

2013-02-05

Electric vehicles (EVs) and compressed natural gas vehicles (CNGVs), which are mainly coal-based and natural gas-based, are the two most widely proposed replacements of gasoline internal combustion engine vehicles (ICEVs) in P.R. China. We examine fuel-cycle emissions of greenhouse gases (GHGs), PM(2.5), PM(10), NO(x), and SO(2) of CNGVs and EVs relative to gasoline ICEVs and hybrids, by Chinese province. CNGVs can currently reduce emissions of GHGs, PM(10), PM(2,5), NO(x), and SO(2) by approximately 6%, 7%, 20%, 18% and 22%, respectively. EVs can reduce GHG emissions by 20%, but increase PM(10), PM(2.5), NO(x), and SO(2) emissions by approximately 360%, 250%, 120%, and 370%, respectively. Nevertheless, results vary significantly by province. Regarding their contribution to national emissions, PM increases from EVs are unimportant, because light-duty passenger vehicles contribute very little to overall PM emissions nationwide (≤0.05%); however, their NO(x) and SO(2) increases are important. Since China is striving to reduce power plant emissions, EVs are expected to have equivalent or even lower SO(2) and NO(x) emissions relative to ICEVs in the future (2030). Before then, however, EVs should be developed according to the cleanness of regional power mixes. This would lower their SO(2) and NO(x) emissions and earn more GHG reduction credits.

Effects of retrofitting emission control systems on in-use heavy diesel vehicles.

PubMed

Millstein, Dev E; Harley, Robert A

2010-07-01

Diesel engines are now the largest source of nitrogen oxides (NO(x)) and fine particulate black carbon (soot) emissions in California. The California Air Resources Board recently adopted a rule requiring that by 2014 all in-use heavy trucks and buses meet current (2007) exhaust particulate matter (PM) emission standards. Also by 2023 all in-use heavy-duty vehicles will have to meet current NO(x) emission standards, with significant progress in achieving the requirements for NO(x) control expected by 2014. This will require retrofit or replacement of older in-use engines. Diesel particle filters (DPF) reduce PM emissions but may increase the NO(2)/NO(x) emission ratio to approximately 35%, compared to approximately 5% typical of diesel engines without particle filters. Additionally, DPF with high oxidative capacity reduce CO and hydrocarbon emissions. We evaluate the effects of retrofitting trucks with DPF on air quality in southern California, using an Eulerian photochemical air quality model. Compared to a 2014 reference scenario without the retrofit program, black carbon concentrations decreased by 12 +/- 2% and 14 +/- 2% during summer and fall, respectively, with corresponding increases in ambient ozone concentrations of 3 +/- 2% and 7 +/- 3%. NO(2) concentrations decreased by 2-4% overall despite the increase in primary NO(2) emissions because total NO(x) emissions were reduced as part of the program to retrofit NO(x) control systems on in-use engines. However, in some cases NO(2) concentrations may increase at locations with high diesel truck traffic.

DEVELOPMENT AND DEMONSTRATION OF NOVEL LOW-NOx BURNERS IN THE STEEL INDUSTRY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cygan, David

Gas Technology Institute (GTI), together with Hamworthy Peabody Combustion Incorporated (formerly Peabody Engineering Corporation), the University of Utah, and Far West Electrochemical have developed and demonstrated an innovative combustion system suitable for natural gas and coke-oven gas firing within the steel industry. The combustion system is a simple, low-cost, energy-efficient burner that can reduce NOx by more than 75%. The U.S. steel industry needs to address NOx control at its steelmaking facilities. A significant part of NOx emissions comes from gas-fired boilers. In steel plants, byproduct gases – blast furnace gas (BFG) and coke-oven gas (COG) – are widely usedmore » together with natural gas to fire furnaces and boilers. In steel plants, natural gas can be fired together with BFG and COG, but, typically, the addition of natural gas raises NOx emissions, which can already be high because of residual fuel-bound nitrogen in COG. The Project Team has applied its expertise in low-NOx burners to lower NOx levels for these applications by combining advanced burner geometry and combustion staging with control strategies tailored to mixtures of natural gas and byproduct fuel gases. These methods reduce all varieties of NOx – thermal NOx produced by high flame temperatures, prompt NOx produced by complex chain reactions involving radical hydrocarbon species and NOx from fuel-bound nitrogen compounds such as ammonia found in COG. The Project Team has expanded GTI’s highly successful low-NOx forced internal recirculation (FIR) burner, previously developed for natural gas-fired boilers, into facilities that utilize BFG and COG. For natural gas firing, these burners have been shown to reduce NOx emissions from typical uncontrolled levels of 80-100 vppm to single-digit levels (9 vppm). This is done without the energy efficiency penalties incurred by alternative NOx control methods, such as external flue gas recirculation (FGR), water injection, and selective non-catalytic reduction. The FIR burner was previously demonstrated on firetube and watertube boilers, and these units are still operating at several industrial and commercial boiler sites in sizes ranging from 2.5 to 60 million Btu/h. This report covers the development of an innovative combustion system suitable for natural gas or coke-oven gas firing within the steel industry. The prototype FIR burner was evaluated on a 20 million Btu/h watertube boiler. Acceptable burner performance was obtained when firing natural gas and simulated coke-oven gas doped with ammonia. The laboratory data reveals a direct relationship between NOx formation and the ammonia concentration in the fuel. In addition, NOx formation increases as the primary stoichiometric ratio (PSR) increases. Representative ammonia concentrations, as documented in the steel industry, ranged from 200 to 500 vppm. When the laboratory burner/boiler was operated with 500 vppm ammonia in the fuel, NOx emissions ranged from 50 to 75 vppm. This, conservatively, is 75% less than state-of-the-art burner performance. When the burner is operated with 200 vppm ammonia in the fuel, the corresponding NOx emissions would range from 30 to 45 vppm, 84% less than present burner technology. During field evaluation on a 174 million Btu/h industrial prototype burner both natural gas and actual COG from on-site generation were tested. Despite the elevated hydrogen cyanide and ammonia content in the COG throughout the test program, the FIR burner showed an improvement over baseline emissions. At full load; 167 million Btu/h, NOx emissions were relatively low at 169 vppm. This represents a 30% reduction compared to baseline emissions not accounting for the higher hydrogen cyanide content in the COG. CO emissions remained below 20 vppm and were stable across the firing range. This represents a 68% reduction compared to baseline CO emissions. When firing natural gas, emissions were stable as firing rate increased over the range. At low fire; 45 million Btu/h, NOx emissions where 33 vppm and increased at full load; 144 million Btu/h, to 49 vppm. CO emissions fluctuated with the oxygen content and remained below 135 vppm during all tests. The boiler’s maximum output was not achieved due to a limitation dictated by the host site natural gas supply. The FIR burner benefits the public by simultaneously addressing the problems of air pollution and energy conservation through a low-NOx combustion technology that does not increase energy consumption. Continuing activities include the negotiation of a license with Hamworthy Peabody Combustion, Incorporated (Hamworthy Peabody) to commercialize the FIR burner for steel industry applications. Hamworthy Peabody is one of the largest U.S. manufacturers of combustion equipment for boilers in the Steel Industry, and has stated their intention to commercialize the FIR burner.« less

Tracking agricultural soil nitric oxide emission variations with novel isotopic measurements

NASA Astrophysics Data System (ADS)

Miller, D. J.; Chai, J.; Guo, F.; Overby, S.; Dell, C. J.; Karsten, H.; Hastings, M. G.

2016-12-01

Agricultural production systems impact the reactive nitrogen cycle via atmospheric nitrogen emissions including nitric oxide, denoted as total nitrogen oxides (NOx). NOx serve as precursors to ozone and nitrate aerosols, influencing air quality, radiative forcing, and ecosystem health. With recent declines in fuel combustion sources, soil emissions are an increasing contributor to NOx budgets. However, spatially heterogeneous, episodic soil NOx pulses are challenging to constrain and remain highly uncertain. Using a novel hourly resolution soil flux chamber-based NOx collection method, we investigate fertilizer management and climatic controls on cropland soil NOx flux and nitrogen isotopic composition (δ15N-NOx) natural abundance variations with field-based and laboratory measurements. No-till, rain-fed corn plots were sampled daily (triplicate isotope samples per treatment per day) following broadcast and shallow-disk injected dairy manure applications as part of a sustainable dairy cropping study in State College, PA (Penn State University; USDA-ARS). Injected manure plots exhibited median fluxes two times higher with larger spatial variations than that for broadcast manure. Soil emission δ15N-NOx signatures of -45 to -20 ‰ were correlated with flux magnitudes across both treatments. Median δ15N-NOx signatures for injected manure were lower with larger spatial variations (-32 ± 9 ‰) than that for broadcast manure (-24 ± 1.5 ‰). These differences are likely linked with higher NH4+ availability for nitrification with injected manure in contrast with higher NH3 volatilization and higher soil δ15N-NH4+ for broadcast manure. Although NOx fluxes were suppressed 1-2 days after heavy rainfall (>35 % water-filled pore space), δ15N-NOx remained consistent. Controlled laboratory incubation studies will also be presented quantifying links with inorganic substrate and fertilizer δ15N. Our observations suggest that agricultural soil δ15N-NOx signatures are linked with fertilizer δ15N and soil NH4+ availability and could serve as an observational tracer of regional fertilizer management gradients. Our results have significant implications for field-scale validations of soil NOx emission inventories and predictions of soil NOx influences on atmospheric oxidation chemistry.

City-specific vehicle emission control strategies to achieve stringent emission reduction targets in China's Yangtze River Delta region.

PubMed

Zhang, Shaojun; Wu, Ye; Zhao, Bin; Wu, Xiaomeng; Shu, Jiawei; Hao, Jiming

2017-01-01

The Yangtze River Delta (YRD) region is one of the most prosperous and densely populated regions in China and is facing tremendous pressure to mitigate vehicle emissions and improve air quality. Our assessment has revealed that mitigating vehicle emissions of NOx would be more difficult than reducing the emissions of other major vehicular pollutants (e.g., CO, HC and PM 2.5 ) in the YRD region. Even in Shanghai, where the emission control implemented are more stringent than in Jiangsu and Zhejiang, we observed little to no reduction in NOx emissions from 2000 to 2010. Emission-reduction targets for HC, NOx and PM 2.5 are determined using a response surface modeling tool for better air quality. We design city-specific emission control strategies for three vehicle-populated cities in the YRD region: Shanghai and Nanjing and Wuxi in Jiangsu. Our results indicate that even if stringent emission control consisting of the Euro 6/VI standards, the limitation of vehicle population and usage, and the scrappage of older vehicles is applied, Nanjing and Wuxi will not be able to meet the NOx emissions target by 2020. Therefore, additional control measures are proposed for Nanjing and Wuxi to further mitigate NOx emissions from heavy-duty diesel vehicles. Copyright © 2016. Published by Elsevier B.V.

Real-time CO2 sensor for the optimal control of electronic EGR system

NASA Astrophysics Data System (ADS)

Kim, Gwang-jung; Choi, Byungchul; Choi, Inchul

2013-12-01

In modern diesel engines, EGR (Exhaust Gas Recirculation) is an important technique used in nitrogen oxide (NOx) emission reduction. This paper describes the development and experimental results of a fiber-optical sensor using a 2.7 μm wavelength absorption to quantify the simultaneous CO2 concentration which is the primary variable of EGR rate (CO2 in the exhaust gas versus CO2 in the intake gas, %). A real-time laser absorption method was developed using a DFB (distributed feedback) diode laser and waveguide to make optimal design and control of electronic EGR system required for `Euro-6' and `Tier 4 Final' NOx emission regulations. While EGR is effective to reduce NOx significantly, the amount of HC and CO is increased in the exhaust gas if EGR rate is not controlled based on driving conditions. Therefore, it is important to recirculate an appropriate amount of exhaust gas in the operation condition generating high volume of NOx. In this study, we evaluated basic characteristics and functions of our optical sensor and studied basically in order to find out optimal design condition. We demonstrated CO2 measurement speed, accuracy and linearity as making a condition similar to real engine through the bench-scale experiment.

Effects of After-Treatment Control Technologies on Heavy-Duty Diesel Truck Emissions

NASA Astrophysics Data System (ADS)

Preble, C.; Dallmann, T. R.; Kreisberg, N. M.; Hering, S. V.; Harley, R.; Kirchstetter, T.

2015-12-01

Diesel engines are major emitters of nitrogen oxides (NOx) and the black carbon (BC) fraction of particulate matter (PM). Diesel particle filter (DPF) and selective catalytic reduction (SCR) emission control systems that target exhaust PM and NOx have recently become standard on new heavy-duty diesel trucks (HDDT). There is concern that DPFs may increase ultrafine particle (UFP) and total particle number (PN) emissions while reducing PM mass emissions. Also, the deliberate catalytic oxidation of engine-out NO to NO2 in continuously regenerating DPFs may lead to increased tailpipe emission of NO2 and near-roadway concentrations that exceed the 1-hr national ambient air quality standard. Increased NO2 emissions can also promote formation of ozone and secondary PM. We report results from ongoing on-road studies of HDDT emissions at the Port of Oakland and the Caldecott Tunnel in California's San Francisco Bay Area. Emission factors (g pollutant per kg diesel) were linked via recorded license plates to each truck's engine model year and installed emission controls. At both sites, DPF use significantly increased the NO2/NOx emission ratio. DPFs also significantly increased NO2 emissions when installed as retrofits on older trucks with higher baseline NOx emissions. While SCR systems on new trucks effectively reduce total NOx emissions and mitigate these undesirable DPF-related NO2 emissions, they also lead to significant emission of N2O, a potent greenhouse gas. When expressed on a CO2-equivalent basis, the N2O emissions increase offsets the fuel economy gain (i.e., the CO2 emission reduction) associated with SCR use. At the Port, average NOx, BC and PN emission factors from new trucks equipped with DPF and SCR were 69 ± 15%, 92 ± 32% and 66 ± 35% lower, respectively, than modern trucks without these emission controls. In contrast, at the Tunnel, PN emissions from older trucks retrofit with DPFs were ~2 times greater than modern trucks without DPFs. The difference could be related to engine temperature, with highway operation producing greater exhaust temperatures that promote UFP nucleation. These studies indicate that DPF and SCR use can mitigate air quality and climate impacts of diesel truck emissions through reductions in BC and NOx. However, increased emissions of N2O, NO2 and PN may offset some of the benefits.

Assessing the effects of oil sands related ozone precursor emissions on ambient ozone levels in the Alberta oil sands region, Canada

NASA Astrophysics Data System (ADS)

Cho, Sunny; Vijayaraghavan, Krish; Spink, David; Cosic, Biljana; Davies, Mervyn; Jung, Jaegun

2017-11-01

A study was undertaken to determine whether, and the extent to which, increased ground-level ozone (O3) precursor emissions from oil sands development have impacted ambient air quality in the north-eastern Alberta, Canada, over the period 1998 to 2012. Temporal trends in emissions of O3 precursors (NOx and VOC) and ambient air concentrations of O3 precursors, and O3 were examined using the Theil-Sen statistical analysis method. Statistically significant correlations between NOx emissions and ambient NOx concentrations were found mainly near surface (open-pit) mining areas where mine fleets are a large source of NOx emissions. No statistically significant trends in the 4th highest daily maximum 8-hr average O3 at any of the continuous and passive ambient air monitoring stations were found. A significant long-term decrease in monthly averaged O3 is observed at some ambient monitoring sites in summer. A visual examination of long-term variations in annual NOx and VOC emissions and annual 4th highest daily maximum 8-hr O3 concentrations does not reveal any indication of a correlation between O3 concentrations and O3 precursor emissions or ambient levels in the study area. Despite a significant increase in oil sands NOx emissions (8%/yr), there is no statistically significant increase in long-term O3 concentrations at any of monitoring stations considered. This suggests that there is surplus NOx available in the environment which results in a titration of ambient O3 in the areas that have ambient monitoring. The limited ambient O3 monitoring data distant from NOx emission sources makes it impossible to assess the impact of these increased O3 precursor levels on O3 levels on a regional scale. As a precautionary measure, the increasing oil sands development O3 precursor emissions would require that priority be given to the management of these emissions to prevent possible future O3 ambient air quality issues.

40 CFR 52.2036 - 1990 base year emission inventory.

Code of Federal Regulations, 2010 CFR

2010-07-01

...—Fairless Hills 1990 VOC and NOX emissions for six emission units (no. 3 blast furnace, no.1 open hearth.... 1 open hearth furnace are 6.9 TPY and 455.5 TPY, respectively. The VOC and NOX emissions from the no...

Fuel-Air Mixing Effect on Nox Emissions for a Lean Premixed-Prevaporized Combustion System

NASA Technical Reports Server (NTRS)

Lee, Chi-Ming; Chun, Kue S.; Locke, Randy J.

1995-01-01

The lean premixed-prevaporized (LPP) concept effectively meets low nitrogen oxides (NOx) emission requirements for combustors with the high inlet temperature and pressure typical of the High-Speed Civil Transport (HSCT). For the LPP system fuel-air mixture uniformity is probably the most important factor for low NOx emissions. Previous studies have suggested that the fuel-air mixture uniformity can be severely affected by changing the number and configuration of fuel injection points. Therefore, an experimental study was performed to determine how the number of fuel injection points and their arrangement affect NOx emissions from an LPP system. The NOx emissions were measured by a gas-sampling probe in a flame-tube rig at the following conditions: inlet temperature of 810 K (1000 F), rig pressure of 10 atm, reference velocity of 150 ft/s, and residence time near 0.005 s. Additionally, a focused Schlieren diagnostic technique coupled with a high speed camera was used to provide a qualitative description of the spatial flow field.

Feasibility of Reburning for Controlling NOx Emissions from Air Force Jet Engine Test Cells

DTIC Science & Technology

1989-06-01

the engine exhaust by the augmenter air. For this reason, it is important to examine the effect of inlet NOX concentration on achieved reduction...Schedule at Tinker AFB .... ......... 8 3 Typical Nonafterburning Turbine Engine Emission Trends. . 9 4 Temperature of Diluted Exhaust J-79 Engine ... Exhaust Temperature on Reburner NOX Reduction .......... ......................... . 43 24 Effect of Exhaust Gas Inlet Flow Rate on Reburner NOx

Modeling of nitrogen oxides (NO(x)) concentrations resulting from ships at berth.

PubMed

Abdul-Wahab, Sabah A; Elkamel, Ali; Al Balushi, Abdullah S; Al-Damkhi, Ali M; Siddiqui, Rafiq A

2008-12-01

Oxides of nitrogen (NO(x)) emissions from ships (marine vessels) contribute to poor air quality that negatively impacts public health and communities in coastal areas and far inland. These emissions often excessively harm human health, environment, wildlife habituates, and quality of life of communities and indigenous of people who live near ports. This study was conducted to assess the impact of NO(x) emissions origination from ships at berth on a nearby community. It was undertaken at Said Bin Sultan Naval base in Wullayat Al-Mussana (Sultanate of Oman) during the year 2005. The Industrial Source Complex Short Term (ISCST) model was adopted to determine the dispersion of NO(x) into port and beyond into surrounding urban areas. The hourly and monthly contours (isopleths) of NO(x) concentrations in and around the port were plotted. The results were analyzed to determine the affected area and the level of NO(x) concentrations. The highest concentration points in the studied area were also identified. The isopleths of NO(x) indicated that most shipping emissions of NO(x) occur at the port can be transported over land. The output results can help to derive advice of recommendations ships operators and environmentalists to take the correct decision to prevent workers and surrounded environment from pollution.

Development of Advanced Low Emission Injectors and High-Bandwidth Fuel Flow Modulation Valves

NASA Technical Reports Server (NTRS)

Mansour, Adel

2015-01-01

Parker Hannifin Corporation developed the 3-Zone fuel nozzle for NASA's Environmentally Responsible Aviation Program to meet NASAs target of 75 LTO NOx reduction from CAEP6 regulation. The nozzle concept was envisioned as a drop-in replacement for currently used fuel nozzle stem, and is built up from laminates to provide energetic mixing suitable for lean direct injection mode at high combustor pressure. A high frequency fuel valve was also developed to provide fuel modulation for the pilot injector. Final testing result shows the LTO NOx level falling just shy of NASAs goal at 31.

Influence of cooled exhaust gas recirculation on performance, emissions and combustion characteristics of LPG fuelled lean burn SI engine

NASA Astrophysics Data System (ADS)

Ravi, K.; Pradeep Bhasker, J.; Alexander, Jim; Porpatham, E.

2017-11-01

On fuel perspective, Liquefied Petroleum Gas (LPG) provides cleaner emissions and also facilitates lean burn signifying less fuel consumption and emissions. Lean burn technology can attain better efficiencies and lesser combustion temperatures but this temperature is quite sufficient to facilitate formation of nitrogen oxide (NOx). Exhaust Gas Recirculation (EGR) for NOx reduction has been considered allover but extremely little literatures exist on the consequence of EGR on lean burn LPG fuelled spark ignition (SI) engine. The following research is carried out to find the optimal rate of EGR addition to reduce NOx emissions without settling on performance and combustion characteristics. A single cylinder diesel engine is altered to operate as LPG fuelled SI engine at a compression ratio of 10.5:1 and arrangements to provide different ratios of cooled EGR in the intake manifold. Investigations are done to arrive at optimum ratio of the EGR to reduce emissions without compromising on performance. Significant reductions in NOx emissions alongside HC and CO emissions were seen. Higher percentages of EGR further diluted the charge and lead to improper combustion and thus increased hydrocarbon emissions. Cooled EGR reduced the peak in-cylinder temperature which reduced NOx emissions but lead to misfire at lower lean limits.

Butanol / Gasoline Mercury CRADA Report

DTIC Science & Technology

2015-03-01

oxygenated fuel, which increases in-cylinder temperatures and thus generates higher NOx emissions. 3.2 Modifications to the SPC-TB 3.2.1 Data Collection...emissions.  Emissions of oxides of Nitrogen (NOx) are higher with oxygenated fuel. NOx generation is a function of the time spent at high temperature ...pressure in the combustion chamber. The engines run leaner and hotter with oxygenated fuel, which increases in-cylinder temperatures and thus

40 CFR 60.4325 - What emission limits must I meet for NOX if my turbine burns both natural gas and distillate oil...

Code of Federal Regulations, 2010 CFR

2010-07-01

... NOX if my turbine burns both natural gas and distillate oil (or some other combination of fuels)? 60... Combustion Turbines Emission Limits § 60.4325 What emission limits must I meet for NOX if my turbine burns... percent natural gas, you must meet the corresponding limit for a natural gas-fired turbine when you are...

40 CFR 60.4325 - What emission limits must I meet for NOX if my turbine burns both natural gas and distillate oil...

Code of Federal Regulations, 2011 CFR

2011-07-01

... NOX if my turbine burns both natural gas and distillate oil (or some other combination of fuels)? 60... Combustion Turbines Emission Limits § 60.4325 What emission limits must I meet for NOX if my turbine burns... percent natural gas, you must meet the corresponding limit for a natural gas-fired turbine when you are...

40 CFR Appendix E to Part 75 - Optional NOX Emissions Estimation Protocol for Gas-Fired Peaking Units and Oil-Fired Peaking Units

Code of Federal Regulations, 2010 CFR

2010-07-01

... the boiler at a normal or conservatively high excess oxygen level in conjunction with these tests....2Substitute 1.25 times the highest NOX emission rate from the baseline correlation tests for the fuel (or fuel... potential NOX emission rate (MER) (as defined in § 72.2 of this chapter) for each unit operating hour...

40 CFR Appendix E to Part 75 - Optional NOX Emissions Estimation Protocol for Gas-Fired Peaking Units and Oil-Fired Peaking Units

Code of Federal Regulations, 2012 CFR

2012-07-01

... the boiler at a normal or conservatively high excess oxygen level in conjunction with these tests....2Substitute 1.25 times the highest NOX emission rate from the baseline correlation tests for the fuel (or fuel... potential NOX emission rate (MER) (as defined in § 72.2 of this chapter) for each unit operating hour...

40 CFR 60.4325 - What emission limits must I meet for NOX if my turbine burns both natural gas and distillate oil...

Code of Federal Regulations, 2012 CFR

2012-07-01

... NOX if my turbine burns both natural gas and distillate oil (or some other combination of fuels)? 60... Combustion Turbines Emission Limits § 60.4325 What emission limits must I meet for NOX if my turbine burns... burning that fuel. Similarly, when your total heat input is greater than 50 percent distillate oil and...

40 CFR 60.4325 - What emission limits must I meet for NOX if my turbine burns both natural gas and distillate oil...

Code of Federal Regulations, 2014 CFR

2014-07-01

... NOX if my turbine burns both natural gas and distillate oil (or some other combination of fuels)? 60... Combustion Turbines Emission Limits § 60.4325 What emission limits must I meet for NOX if my turbine burns... burning that fuel. Similarly, when your total heat input is greater than 50 percent distillate oil and...

40 CFR 60.4325 - What emission limits must I meet for NOX if my turbine burns both natural gas and distillate oil...

Code of Federal Regulations, 2013 CFR

2013-07-01

... NOX if my turbine burns both natural gas and distillate oil (or some other combination of fuels)? 60... Combustion Turbines Emission Limits § 60.4325 What emission limits must I meet for NOX if my turbine burns... burning that fuel. Similarly, when your total heat input is greater than 50 percent distillate oil and...

Reducing secondary organic aerosol formation from gasoline vehicle exhaust

PubMed Central

Zhao, Yunliang; Saleh, Rawad; Presto, Albert A.; Gordon, Timothy D.; Drozd, Greg T.; Goldstein, Allen H.; Robinson, Allen L.

2017-01-01

On-road gasoline vehicles are a major source of secondary organic aerosol (SOA) in urban areas. We investigated SOA formation by oxidizing dilute, ambient-level exhaust concentrations from a fleet of on-road gasoline vehicles in a smog chamber. We measured less SOA formation from newer vehicles meeting more stringent emissions standards. This suggests that the natural replacement of older vehicles with newer ones that meet more stringent emissions standards should reduce SOA levels in urban environments. However, SOA production depends on both precursor concentrations (emissions) and atmospheric chemistry (SOA yields). We found a strongly nonlinear relationship between SOA formation and the ratio of nonmethane organic gas to oxides of nitrogen (NOx) (NMOG:NOx), which affects the fate of peroxy radicals. For example, changing the NMOG:NOx from 4 to 10 ppbC/ppbNOx increased the SOA yield from dilute gasoline vehicle exhaust by a factor of 8. We investigated the implications of this relationship for the Los Angeles area. Although organic gas emissions from gasoline vehicles in Los Angeles are expected to fall by almost 80% over the next two decades, we predict no reduction in SOA production from these emissions due to the effects of rising NMOG:NOx on SOA yields. This highlights the importance of integrated emission control policies for NOx and organic gases. PMID:28630318

Using Satellite Remote Sensing and Modelling for Insights into N02 Air Pollution and NO2 Emissions

NASA Technical Reports Server (NTRS)

Lamsal, L. N.; Martin, R. V.; Krotkov, N. A.; Bucsela, E. J.; Celarier, E. A.; vanDonkelaar, A.; Parrish, D.

2012-01-01

Nitrogen oxides (NO(x)) are key actors in air quality and climate change. Satellite remote sensing of tropospheric NO2 has developed rapidly with enhanced spatial and temporal resolution since initial observations in 1995. We have developed an improved algorithm and retrieved tropospheric NO2 columns from Ozone Monitoring Instrument. Column observations of tropospheric NO2 from the nadir-viewing satellite sensors contain large contributions from the boundary layer due to strong enhancement of NO2 in the boundary layer. We infer ground-level NO2 concentrations from the OMI satellite instrument which demonstrate significant agreement with in-situ surface measurements. We examine how NO2 columns measured by satellite, ground-level NO2 derived from satellite, and NO(x) emissions obtained from bottom-up inventories relate to world's urban population. We perform inverse modeling analysis of NO2 measurements from OMI to estimate "top-down" surface NO(x) emissions, which are used to evaluate and improve "bottom-up" emission inventories. We use NO2 column observations from OMI and the relationship between NO2 columns and NO(x) emissions from a GEOS-Chem model simulation to estimate the annual change in bottom-up NO(x) emissions. The emission updates offer an improved estimate of NO(x) that are critical to our understanding of air quality, acid deposition, and climate change.

Pollutant emissions from flat-flame burners at high pressures

NASA Technical Reports Server (NTRS)

Maahs, H. G.; Miller, I. M.

1980-01-01

Maximum flame temperatures and pollutant emission measurements for NOx, CO, and UHC (unburned hydrocarbons) are reported for premixed methane air flat flames at constant total mass flow rate over the pressure range from 1.9 to 30 atm and for equivalence ratios from 0.84 to 1.12. For any given pressure, maxima typically occur in both the temperature and NOx emissions curves slightly to the lean side of stoichiometric conditions. The UHC emissions show minima at roughly the same equivalence ratios. The CO emissions, however, increase continually with increasing equivalence ratio. Flame temperature and NOx emissions decrease with increasing pressure, while the opposite is true for the CO and UHC emissions. The NOx data correlate reasonably well as a function of flame temperature only. Four flameholders, differing only slightly, were used. In general, the temperature and emissions data from these four flameholders are similar, but some differences also exist. These differences appear to be related to minor variations in the condition of the flameholder surfaces.

Wetting-induced pulses produced unexpectedly high emissions of N2O and NOx in a desert ecosystem

NASA Astrophysics Data System (ADS)

Eberwein, J. R.; Carey, C.; Aronson, E. L.; Jenerette, D.

2015-12-01

Approximately one third of Earth's land surface is subjected to arid conditions, and aridland soils have the potential for significant feedbacks to global climate change drivers, such as anthropogenic nitrogen deposition. This study examined wetting-induced pulses of N2O and NOx along a nitrogen deposition gradient in the Colorado Desert of southern California. Measurements were made before and following water (to simulate a 2 cm rain event) and nitrogen plus water additions (30 kg NH4NO3 ha-1) at 15 minutes, 12 hours and 24 hours post-wetting. We found nitrogenous fluxes that were substantially higher than expected. N2O fluxes, in particular were remarkably high reaching up to 200 ng N2O-N m-2 s-1, similar to agriculture levels and in the range of peat bog emissions. There was a clear transition between N2O emissions, which peaked 15 minutes after wetting, and NOx emissions, which peaked at the 12 hour timepoint. NOx emissions were also considerable, reaching as high as 350 ng NOx-N m-2 s-1. Both N2O and NOx fluxes responded strongly to water additions, demonstrating a clear wetting-induced pulse response. While N2O was not affected by nitrogen additions, NOx fluxes demonstrated a significant increase with nitrogen plus water over water alone (p=0.016). These results suggest that gaseous nitrogen export, particularly N2O emissions, is a greater form of nitrogen loss in arid systems than is currently assumed. This potential for high nitrogen emissions and the capacity for anthropogenic nitrogen deposition to increase these emissions present serious implications for local air quality and significant soil feedbacks to climate change.

Regional modeling of tropospheric NO2 vertical column density over East Asia during the period 2000-2010: comparison with multisatellite observations

NASA Astrophysics Data System (ADS)

Itahashi, S.; Uno, I.; Irie, H.; Kurokawa, J.-I.; Ohara, T.

2014-04-01

Satellite observations of the tropospheric NO2 vertical column density (VCD) are closely correlated to, and thus can be used to estimate, surface NOx emissions. In this study, the NO2 VCD simulated by a regional chemical transport model with emissions data from the updated Regional Emission inventory in ASia (REAS) version 2.1 were validated through comparison with multisatellite observations during the period 2000-2010. Rapid growth in NO2 VCD (~11% year-1) driven by the expansion of anthropogenic NOx emissions was identified above the central eastern China (CEC) region, except for the period during the economic downturn. In contrast, slightly decreasing trends (~2% year-1) were identified above Japan accompanied by a decline in anthropogenic emissions. To systematically compare the modeled NO2 VCD, we estimated sampling bias and the effect of applying the averaging kernel information, with particular focus on the SCanning Imaging Absorption spectroMeter for Atmospheric CHartographY (SCIAMACHY) data. Using the updated REAS, the modeled NO2 VCD reasonably reproduced annual trends observed by multisatellites, suggesting that the rate of increase of NOx emissions estimated by the updated REAS inventory would be robust. Province-scale revision of emissions above CEC is needed to further refine emission inventories. Based on the close linear relationship between modeled and observed NO2 VCD and anthropogenic NOx emissions, NOx emissions in 2009 and 2010, which were not covered by the updated REAS inventory, were estimated. NOx emissions from anthropogenic sources in China in 2009 and 2010 were determined to be 26.4 and 28.5 Tg year-1, respectively, indicating that NOx emissions increased more than twofold between 2000 and 2010. This increase reflected the strong growth of anthropogenic emissions in China following the rapid recovery from the economic downturn from late 2008 until mid-2009. Our method consists of simple estimations from satellite observations and provides results that are consistent with the most recent inventory of emissions data for China.

Real-time measurements of nitrogen oxide emissions from in-use New York City transit buses using a chase vehicle.

PubMed

Shorter, Joanne H; Herndon, Scott; Zahniser, Mark S; Nelson, David D; Wormhoudt, Joda; Demerjian, Kenneth L; Kolb, Charles E

2005-10-15

New diesel engine technologies and alternative fuel engines are being introduced into fleets of mass transit buses to try to meet stricter emission regulations of nitrogen oxides and particulates: Real-time instruments including an Aerodyne Research tunable infrared laser differential absorption spectrometer (TILDAS) were deployed in a mobile laboratory to assess the impact of the implementation of the new technologies on nitrogen oxide emissions in real world driving conditions. Using a "chase" vehicle sampling strategy, the mobile laboratory followed target vehicles, repeatedly sampling their exhaust. Nitrogen oxides from approximately 170 in-use New York City mass transit buses were sampled during the field campaigns. Emissions from conventional diesel buses, diesel buses with continuously regenerating technology (CRT), diesel hybrid electric buses, and compressed natural gas (CNG) buses were compared. The chase vehicle sampling method yields real world emissions that can be included in more realistic emission inventories. The NO, emissions from the diesel and CNG buses were comparable. The hybrid electric buses had approximately one-half the NOx emissions. In CRT diesels, NO2 accounts for about one-third of the NOx emitted in the exhaust, while for non-CRT buses the NO2 fraction is less than 10%.

[Predicting low NOx combustion property of a coal-fired boiler].

PubMed

Zhou, Hao; Mao, Jianbo; Chi, Zuohe; Jiang, Xiao; Wang, Zhenhua; Cen, Kefa

2002-03-01

More attention was paid to the low NOx combustion property of the high capacity tangential firing boiler, but the NOx emission and unburned carbon content in fly ash of coal burned boiler were complicated, they were affected by many factors, such as coal character, boiler's load, air distribution, boiler style, burner style, furnace temperature, excess air ratio, pulverized coal fineness and the uniformity of the air and coal distribution, etc. In this paper, the NOx emission property and unburned carbon content in fly ash of a 600 MW utility tangentially firing coal burned boiler was experimentally investigated, and taking advantage of the nonlinear dynamics characteristics and self-learning characteristics of artificial neural network, an artificial neural network model on low NOx combustion property of the high capacity boiler was developed and verified. The results illustrated that such a model can predicate the NOx emission concentration and unburned carbon content under various operating conditions, if combined with the optimization algorithm, the operator can find the best operation condition of the low NOx combustion.

Regulatory impact analysis and regulatory support document: Control of air pollution; determination of significance for nonroad sources and emission standards for new nonroad compression-ignition engines at or above 37 kilowatts (50 horsepower). Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Trimble, T.; North, D.R.; Green, K.A.H.

1994-05-27

The regulatory impact analysis and support document provides additional information in support of the Final Rulemaking (FRM). This FRM will regulate all new nonroad compression-ignition engines greater than or equal to 37 kilowatts (50 hp), except engines which propel or are used on marine vessels, aircraft engines, engines which propel locomotives, and engines regulated by the Mining, Safety, and Health Administration. The regulated engines are hereafter referred to as nonroad large CI engines. The goal of this regulation is to substantially reduce NOx emission and smoke from nonroad large CI engines beginning in the 1996 model year.

40 CFR 76.5 - NOX emission limitations for Group 1 boilers.

Code of Federal Regulations, 2011 CFR

2011-07-01

... PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.5 NOX emission limitations..., the date on which the unit is required to meet Acid Rain emission reduction requirements for SO2, the... 404(d) of the Act, the date the unit is required to meet Acid Rain emissions reduction requirements...

40 CFR 76.5 - NOX emission limitations for Group 1 boilers.

Code of Federal Regulations, 2012 CFR

2012-07-01

... PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.5 NOX emission limitations..., the date on which the unit is required to meet Acid Rain emission reduction requirements for SO2, the... 404(d) of the Act, the date the unit is required to meet Acid Rain emissions reduction requirements...

40 CFR 76.5 - NOX emission limitations for Group 1 boilers.

Code of Federal Regulations, 2013 CFR

2013-07-01

... PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.5 NOX emission limitations..., the date on which the unit is required to meet Acid Rain emission reduction requirements for SO2, the... 404(d) of the Act, the date the unit is required to meet Acid Rain emissions reduction requirements...

40 CFR 80.91 - Individual baseline determination.

Code of Federal Regulations, 2013 CFR

2013-07-01

...—6.45 Exhaust benzene emissions, complex model—33.03 mg/mile Exhaust toxics emissions, Phase I—50.67 mg/mile Exhaust toxics emissions, Phase II—104.5 mg/mile NOX emissions, Phase I—714.4 mg/mile NOX emissions, Phase II—1461. mg/mile (d) Data collection and testing requirements—(1) Minimum sampling...

40 CFR 80.91 - Individual baseline determination.

Code of Federal Regulations, 2014 CFR

2014-07-01

...—6.45 Exhaust benzene emissions, complex model—33.03 mg/mile Exhaust toxics emissions, Phase I—50.67 mg/mile Exhaust toxics emissions, Phase II—104.5 mg/mile NOX emissions, Phase I—714.4 mg/mile NOX emissions, Phase II—1461. mg/mile (d) Data collection and testing requirements—(1) Minimum sampling...

40 CFR 80.91 - Individual baseline determination.

Code of Federal Regulations, 2011 CFR

2011-07-01

...—6.45 Exhaust benzene emissions, complex model—33.03 mg/mile Exhaust toxics emissions, Phase I—50.67 mg/mile Exhaust toxics emissions, Phase II—104.5 mg/mile NOX emissions, Phase I—714.4 mg/mile NOX emissions, Phase II—1461. mg/mile (d) Data collection and testing requirements—(1) Minimum sampling...

40 CFR 80.91 - Individual baseline determination.

Code of Federal Regulations, 2010 CFR

2010-07-01

...—6.45 Exhaust benzene emissions, complex model—33.03 mg/mile Exhaust toxics emissions, Phase I—50.67 mg/mile Exhaust toxics emissions, Phase II—104.5 mg/mile NOX emissions, Phase I—714.4 mg/mile NOX emissions, Phase II—1461. mg/mile (d) Data collection and testing requirements—(1) Minimum sampling...

Trends in on-road vehicle emissions and ambient air quality in Atlanta, Georgia, USA, from the late 1990s through 2009.

PubMed

Vijayaraghavan, Krish; DenBleyker, Allison; Ma, Lan; Lindhjem, Chris; Yarwood, Greg

2014-07-01

On-road vehicle emissions of carbon monoxide (CO), nitrogen oxides (NO(x)), and volatile organic compounds (VOCs) during 1995-2009 in the Atlanta Metropolitan Statistical Area were estimated using the Motor Vehicle Emission Simulator (MOVES) model and data from the National Emissions Inventories and the State of Georgia. Statistically significant downward trends (computed using the nonparametric Theil-Sen method) in annual on-road CO, NO(x), and VOC emissions of 6.1%, 3.3%, and 6.0% per year, respectively, are noted during the 1995-2009 period despite an increase in total vehicle distance traveled. The CO and NO(x) emission trends are correlated with statistically significant downward trends in ambient air concentrations of CO and NO(x) in Atlanta ranging from 8.0% to 11.8% per year and from 5.8% to 8.7% per year, respectively, during similar time periods. Weather-adjusted summertime ozone concentrations in Atlanta exhibited a statistically significant declining trend of 2.3% per year during 2001-2009. Although this trend coexists with the declining trends in on-road NO(x), VOC, and CO emissions, identifying the cause of the downward trend in ozone is complicated by reductions in multiple precursors from different source sectors. Implications: Large reductions in on-road vehicle emissions of CO and NO(x) in Atlanta from the late 1990s to 2009, despite an increase in total vehicle distance traveled, contributed to a significant improvement in air quality through decreases in ambient air concentrations of CO and NO(x) during this time period. Emissions reductions in motor vehicles and other source sectors resulted in these improvements and the observed declining trend in ozone concentrations over the past decade. Although these historical trends cannot be extrapolated to the future because pollutant concentration contributions due to on-road vehicle emissions will likely become an increasingly smaller fraction of the atmospheric total, they provide an indication of the benefits of past control measures.

NOx reduction through combustion optimization at PEPCO`s Potomac River Station

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cramer, D.S.; Williams, S.E.; Watkins, J.T.

1995-06-01

This paper describes the work done under EPRI Project RP 3383 at Potomac River Station to reduce NOx emissions by adjusting boiler controls. it details the method followed by PEPCO and Lehigh engineers to achieve a 35% reduction in average NOx emissions over a one-month extended test. Parameters that had the largest effect on NOx are discussed. A description of instruments installed to better monitor and control combustion is included.

COMPARISON OF CLEAN DIESEL BUSES TO CNG BUSES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lowell, D.; Parsley, W.; Bush,C

2003-08-24

Using previously published data on regulated and unregulated emissions, this paper will compare the environmental performance of current generation transit buses operated on compressed natural gas (CNG) to current generation transit buses operated on ultra low sulfur diesel fuel (ULSD) and incorporating diesel particulate filters (DPF). Unregulated emissions evaluated include toxic compounds associated with adverse health effects (carbonyl, PAH, NPAH, benzene) as well as PM particle count and size distribution. For all regulated and unregulated emissions, both technologies are shown to be comparable. DPF equipped diesel buses and CNG buses have virtually identical levels of PM mass emissions and particlemore » number emissions. DPF-equipped diesel buses have lower HC and CO emissions and lower emissions of toxic substances such as benzene, carbonyls and PAHs than CNG buses. CNG buses have lower NOx emissions than DPF-equipped buses, though CNG bus NOx emissions are shown to be much more variable. In addition, this paper will compare the capital and operating costs of CNG and DPF-equipped buses. The cost comparison is primarily based on the experience of MTA New York City Transit in operating CNG buses since 1995 and DPF-equipped buses fueled with ULSD since 2001. Published data on the experience of other large transit agencies in operating CNG buses is used to validate the NYCT experience. The incremental cost (compared to ''baseline'' diesel) of operating a typical 200-bus depot is shown to be six times higher for CNG buses than for ''clean diesel'' buses. The contributors to this increased cost for CNG buses are almost equally split between increased capital costs for purchase of buses and installation of fueling infrastructure, and increased operating costs for purchase of fuel, bus maintenance, and fuel station maintenance.« less

Real-time gaseous, PM and ultrafine particle emissions from a modern marine engine operating on biodiesel.

PubMed

Jayaram, Varalakshmi; Agrawal, Harshit; Welch, William A; Miller, J Wayne; Cocker, David R

2011-03-15

Emissions from harbor-craft significantly affect air quality in populated regions near ports and inland waterways. This research measured regulated and unregulated emissions from an in-use EPA Tier 2 marine propulsion engine on a ferry operating in a bay following standard methods. A special effort was made to monitor continuously both the total Particulate Mass (PM) mass emissions and the real-time Particle Size Distribution (PSD). The engine was operated following the loads in ISO 8178-4 E3 cycle for comparison with the certification standards and across biodiesel blends. Real-time measurements were also made during a typical cruise in the bay. Results showed the in-use nitrogen oxide (NOx) and PM(2.5) emission factors were within the not to exceed standard for Tier 2 marine engines. Comparing across fuels we observed the following: a) no statistically significant change in NO(x) emissions with biodiesel blends (B20, B50); b) ∼ 16% and ∼ 25% reduction of PM(2.5) mass emissions with B20 and B50 respectively; c) a larger organic carbon (OC) to elemental carbon (EC) ratio and organic mass (OM) to OC ratio with B50 compared to B20 and B0; d) a significant number of ultrafine nuclei and a smaller mass mean diameter with increasing blend-levels of biodiesel. The real-time monitoring of gaseous and particulate emissions during a typical cruise in the San Francisco Bay (in-use cycle) revealed important effects of ocean/bay currents on emissions: NO(x) and CO(2) increased 3-fold; PM(2.5) mass increased 6-fold; and ultrafine particles disappeared due to the effect of bay currents. This finding has implications on the use of certification values instead of actual in-use emission values when developing inventories. Emission factors for some volatile organic compounds (VOCs), carbonyls, and poly aromatic hydrocarbons (PAHs) are reported as supplemental data.

Estimates of ozone response to various combinations of NO(x) and VOC emission reductions in the eastern United States

NASA Technical Reports Server (NTRS)

Roselle, Shawn J.; Schere, Kenneth L.; Chu, Shao-Hang

1994-01-01

There is increasing recognition that controls on NO(x) emissions may be necessary, in addition to existing and future Volatile Organic Compounds (VOC) controls, for the abatement of ozone (O3) over portions of the United States. This study compares various combinations of anthropogenic NO(x) and VOC emission reductions through a series of model simulations. A total of 6 simulations were performed with the Regional Oxidant Model (ROM) for a 9-day period in July 1988. Each simulation reduced anthropogenic NO(x) and VOC emissions across-the-board by different amounts. Maximum O3 concentrations for the period were compared between the simulations. Comparison of the simulations suggests that: (1) NO(x) controls may be more effective than VOC controls in reducing peak O3 over most of the eastern United States; (2) VOC controls are most effective in urban areas having large sources of emissions; (3) NO(x) controls may increase O3 near large point sources; and (4) the benefit gained from increasing the amount of VOC controls may lessen as the amount of NO(x) control is increased. This paper has been reviewed in accordance with the U.S. Environmental Protection Agency's peer and administrative review policies and approved for presentation and publication. Mention of trade names or commercial products does not constitute endorsement or recommendation for use.

Review of Diesel Combustion Models for NOx and Smoke Emissions

DOT National Transportation Integrated Search

1977-10-01

A comprehensive review of diesel emissions models is presented together with assessments of the pertinent fundamental NOx and soot kinetics. The results of diesel emissions experiments carried out at Southampton are also presented and correlations ar...

A new method and application for determining the nitrogen isotopic composition of NOx

NASA Astrophysics Data System (ADS)

Hastings, M. G.; Miller, D. J.; Wojtal, P.; O'Connor, M.

2015-12-01

Atmospheric nitrogen oxides (NOx = NO + NO2) play key roles in atmospheric chemistry, air quality, and radiative forcing, and contribute to nitric acid deposition. Sources of NOx include both natural and anthropogenic emissions, which vary significantly in space and time. NOx isotopic signatures offer a potentially valuable tool to trace source impacts on atmospheric chemistry and regional acid deposition. Previous work on NOx isotopic signatures suggests large ranges in values, even from the same emission source, as well as overlapping ranges amongst different sources, making it difficult to use the isotopic composition as a quantitative tracer of source influences. These prior measurements have utilized a variety of methods for collecting the NOx as nitrate or nitrite for isotopic analysis, and testing of some of these methods (including active and passive collections) reveal inconsistencies in efficiency of collection, as well as issues related to changes in conditions such as humidity, temperature, and NOx fluxes. A recently developed method allows for accurately measuring the nitrogen isotopic composition of NOx (NOx = NO + NO2) after capturing the NOx in a potassium permanganate/sodium hydroxide solution as nitrate (Fibiger et al., Anal. Chem., 2014). The method has been thoroughly tested in the laboratory and field, and efficiently collects NO and NO2 under a variety of conditions. There are several advantages to collecting NOx actively, including the ability to collect over minutes to hourly time scales, and the ability to collect in environments with highly variable NOx sources and concentrations. Challenges include a nitrate background present in potassium permanganate (solid and liquid forms), accurately deriving ambient NOx concentrations based upon flow rate and solution concentrations above this variable background, and potential interferences from other nitrogen species. This method was designed to collect NOx in environments with very different emission source loadings in an effort to isotopically characterize NOx sources. Results to date suggest very different values, and less variability than previous work, particularly for vehicle emissions. Ultimately, we aim to determine whether the influence of NOx sources can be quantitatively tracked in the environment.

Effect of water injection on nitric oxide emissions of a gas turbine combustor burning natural gas fuel

NASA Technical Reports Server (NTRS)

Marchionna, N. R.; Diehl, L. A.; Trout, A. M.

1973-01-01

The effect of direct water injection on the exhaust gas emissions of a turbojet combustor burning natural gas fuel was investigated. The results are compared with the results from similar tests using ASTM Jet-A fuel. Increasing water injection decreased the emissions of oxides of nitrogen (NOX) and increased the emissions of carbon monoxide and unburned hydrocarbons. The greatest percentage decrease in NOX with increasing water injection was at the lowest inlet-air temperature tested. The effect of increasing inlet-air temperature was to decrease the effect of the water injection. The reduction in NOX due to water injection was almost identical to the results obtained with Jet-A fuel. However, the emission indices of unburned hydrocarbons, carbon monoxide, and percentage nitric oxide in NOX were not.

A spatially resolved fuel-based inventory of Utah and Colorado oil and natural gas emissions

NASA Astrophysics Data System (ADS)

Gorchov Negron, A.; McDonald, B. C.; De Gouw, J. A.; Frost, G. J.

2015-12-01

A fuel-based approach is presented for estimating emissions from US oil and natural gas production that utilizes state-level fuel surveys of oil and gas engine activity, well-level production data, and emission factors for oil and gas equipment. Emissions of carbon dioxide (CO2) and nitrogen oxides (NOx) are mapped on a 4 km x 4 km horizontal grid for 2013-14 in Utah and Colorado. Emission sources include combustion from exploration (e.g., drilling), production (e.g., heaters, dehydrators, and compressor engines), and natural gas processing plants, which comprise a large fraction of the local combustion activity in oil and gas basins. Fuel-based emission factors of NOx are from the U.S. Environmental Protection Agency, and applied to spatially-resolved maps of CO2 emissions. Preliminary NOx emissions from this study are estimated for the Uintah Basin, Utah, to be ~5300 metric tons of NO2-equivalent in 2013. Our result compares well with an observations-based top-down emissions estimate of NOx derived from a previous study, ~4200 metric tons of NO2-equivalent. By contrast, the 2011 National Emissions Inventory estimates oil and gas emissions of NOx to be ~3 times higher than our study in the Uintah Basin. We intend to expand our fuel-based approach to map combustion-related emissions in other U.S. oil and natural gas basins and compare with additional observational datasets.

40 CFR 94.304 - Compliance requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... specified in this part, except that the applicable FEL replaces the applicable THC+NOX and PM emission... life shall be unlimited. (m) Upper limits. The FELs for THC+NOX and PM for new engines certified for...—Category 1 Upper Limits for Tier 2 Family Emission Limits Subcategory liters/cylinder Model year 1 THC+NOX...

40 CFR 94.304 - Compliance requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... specified in this part, except that the applicable FEL replaces the applicable THC+NOX and PM emission... life shall be unlimited. (m) Upper limits. The FELs for THC+NOX and PM for new engines certified for...—Category 1 Upper Limits for Tier 2 Family Emission Limits Subcategory liters/cylinder Model year 1 THC+NOX...

40 CFR 94.304 - Compliance requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... specified in this part, except that the applicable FEL replaces the applicable THC+NOX and PM emission... life shall be unlimited. (m) Upper limits. The FELs for THC+NOX and PM for new engines certified for...—Category 1 Upper Limits for Tier 2 Family Emission Limits Subcategory liters/cylinder Model year 1 THC+NOX...

40 CFR 94.304 - Compliance requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... specified in this part, except that the applicable FEL replaces the applicable THC+NOX and PM emission... life shall be unlimited. (m) Upper limits. The FELs for THC+NOX and PM for new engines certified for...—Category 1 Upper Limits for Tier 2 Family Emission Limits Subcategory liters/cylinder Model year 1 THC+NOX...

40 CFR 94.304 - Compliance requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... specified in this part, except that the applicable FEL replaces the applicable THC+NOX and PM emission... life shall be unlimited. (m) Upper limits. The FELs for THC+NOX and PM for new engines certified for...—Category 1 Upper Limits for Tier 2 Family Emission Limits Subcategory liters/cylinder Model year 1 THC+NOX...

40 CFR 97.534 - Recordkeeping and reporting.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Acid Rain Program or a TR NOX Annual emissions limitation or if the owner or operator of such unit... not subject to the Acid Rain Program or a TR NOX Annual emissions limitation, then the designated... Ozone Season units that are also subject to the Acid Rain Program, TR NOX Annual Trading Program, TR SO2...

40 CFR 97.534 - Recordkeeping and reporting.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Acid Rain Program or a TR NOX Annual emissions limitation or if the owner or operator of such unit... not subject to the Acid Rain Program or a TR NOX Annual emissions limitation, then the designated... Ozone Season units that are also subject to the Acid Rain Program, TR NOX Annual Trading Program, TR SO2...

40 CFR 97.534 - Recordkeeping and reporting.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Acid Rain Program or a TR NOX Annual emissions limitation or if the owner or operator of such unit... not subject to the Acid Rain Program or a TR NOX Annual emissions limitation, then the designated... Ozone Season units that are also subject to the Acid Rain Program, TR NOX Annual Trading Program, TR SO2...

Speciation and chemical evolution of nitrogen oxides in aircraft exhaust near airports.

PubMed

Wood, Ezra C; Herndon, Scott C; Timko, Michael T; Yelvington, Paul E; Miake-Lye, Richard C

2008-03-15

Measurements of nitrogen oxides from a variety of commercial aircraft engines as part of the JETS-APEX2 and APEX3 campaigns show that NOx (NOx [triple bond] NO + NO2) is emitted primarily in the form of NO2 at idle thrust and NO at high thrust. A chemical kinetics combustion model reproduces the observed NO2 and NOx trends with engine power and sheds light on the relevant chemical mechanisms. Experimental evidence is presented of rapid conversion of NO to NO2 in the exhaust plume from engines at low thrust. The rapid conversion and the high NO2/NOx emission ratios observed are unrelated to ozone chemistry. NO2 emissions from a CFM56-3B1 engine account for approximately 25% of the NOx emitted below 3000 feet (916 m) and 50% of NOx emitted below 500 feet (153 m) during a standard ICAO (International Civil Aviation Organization) landing-takeoff cycle. Nitrous acid (HONO) accounts for 0.5% to 7% of NOy emissions from aircraft exhaust depending on thrust and engine type. Implications for photochemistry near airports resulting from aircraft emissions are discussed.

Analysis of effect of flameholder characteristics on lean, premixed, partially vaporized fuel-air mixtures quality and nitrogen oxides emissions

NASA Technical Reports Server (NTRS)

Cooper, L. P.

1981-01-01

An analysis was conducted of the effect of flameholding devices on the precombustion fuel-air characteristics and on oxides of nitrogen (NOx) emissions for combustion of premixed partially vaporized mixtures. The analysis includes the interrelationships of flameholder droplet collection efficiency, reatomization efficiency and blockage, and the initial droplet size distribution and accounts for the contribution of droplet combustion in partially vaporized mixtures to NOx emissions. Application of the analytical procedures is illustrated and parametric predictions of NOx emissions are presented.

COMPARISON OF HISTORIC SO2 AND NOX EMISSION DATA SETS

EPA Science Inventory

The report gives results of a comparison of historic SO2 and NOx emission data sets. During the past few years, several research projects have been conducted to reconstruct historic air pollution emission trends in the U.S. The report compares in detail the emission estimates and...

Emissions of an AVCO Lycoming 0-320-DIAD air cooled light aircraft engine as a function of fuel-air ratio, timing, and air temperature and humidity

NASA Technical Reports Server (NTRS)

Meng, P. R.; Skorobatckyi, M.; Cosgrove, D. V.; Kempke, E. E., Jr.

1976-01-01

A carbureted aircraft engine was operated over a range of test conditions to establish the exhaust levels over the EPA seven-mode emissions cycle. Baseline (full rich production limit) exhaust emissions at an induction air temperature of 59 F and near zero relative humidity were 90 percent of the EPA standard for HC, 35 percent for NOx, and 161 percent for CO. Changes in ignition timing around the standard 25 deg BTDC from 30 deg BTDC to 20 deg BTDC had little effect on the exhaust emissions. Retarding the timing to 15 deg BTDC increased both the HC and CO emissions and decreased NOx emissions. HC and CO emissions decreased as the carburetor was leaned out, while NOx emissions increased. The EPA emission standards were marginally achieved at two leanout conditions. Variations in the quantity of cooling air flow over the engine had no effect on exhaust emissions. Temperature-humidity effects at the higher values of air temperature and relative humidity tested indicated that the HC and CO emissions increased significantly, while the NOx emissions decreased.

Temporal characteristics of atmospheric ammonia and nitrogen dioxide over China based on emission data, satellite observations and atmospheric transport modeling since 1980

NASA Astrophysics Data System (ADS)

Liu, Lei; Zhang, Xiuying; Xu, Wen; Liu, Xuejun; Li, Yi; Lu, Xuehe; Zhang, Yuehan; Zhang, Wuting

2017-08-01

China is experiencing intense air pollution caused in large part by anthropogenic emissions of reactive nitrogen (Nr). Atmospheric ammonia (NH3) and nitrogen dioxide (NO2) are the most important precursors for Nr compounds (including N2O5, HNO3, HONO and particulate NO3- and NH4+) in the atmosphere. Understanding the changes in NH3 and NO2 has important implications for the regulation of anthropogenic Nr emissions and is a requirement for assessing the consequence of environmental impacts. We conducted the temporal trend analysis of atmospheric NH3 and NO2 on a national scale since 1980 based on emission data (during 1980-2010), satellite observation (for NH3 since 2008 and for NO2 since 2005) and atmospheric chemistry transport modeling (during 2008-2015).Based on the emission data, during 1980-2010, significant continuous increasing trends in both NH3 and NOx were observed in REAS (Regional Emission inventory in Asia, for NH3 0.17 and for NOx 0.16 kg N ha-1 yr-2) and EDGAR (Emissions Database for Global Atmospheric Research, for NH3 0.24 and for NOx 0.17 kg N ha-1 yr-2) over China. Based on the satellite data and atmospheric chemistry transport model (CTM) MOZART-4 (Model for Ozone and Related chemical Tracers, version 4), the NO2 columns over China increased significantly from 2005 to 2011 and then decreased significantly from 2011 to 2015; the satellite-retrieved NH3 columns from 2008 to 2014 increased at a rate of 2.37 % yr-1. The decrease in NO2 columns since 2011 may result from more stringent strategies taken to control NOx emissions during the 12th Five Year Plan, while no control policy has focused on NH3 emissions. Our findings provided an overall insight into the temporal trends of both NO2 and NH3 since 1980 based on emission data, satellite observations and atmospheric transport modeling. These findings can provide a scientific background for policy makers that are attempting to control atmospheric pollution in China. Moreover, the multiple datasets used in this study have implications for estimating long-term Nr deposition datasets to assess its impact on soil, forest, water and greenhouse balance.

40 CFR 76.5 - NOX emission limitations for Group 1 boilers.

Code of Federal Regulations, 2014 CFR

2014-07-01

... PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.5 NOX emission limitations..., the date on which the unit is required to meet Acid Rain emission reduction requirements for SO2, the... subject to section 404(d) of the Act, the date the unit is required to meet Acid Rain emissions reduction...

Environmental assessment of an enhanced-oil-recovery steam generator equipped with a low-NOx burner. Volume 1. Technical results. Final report, January 1984-January 1985

DOE Office of Scientific and Technical Information (OSTI.GOV)

Castaldini, C.; Waterland, L.R.; Lips, H.I.

1986-02-01

The report discusses results from sampling flue gas from an enhanced-oil-recovery steam generator (EOR steamer) equipped with an MHI PM low-NOx burner. The tests included burner performance/emission mapping tests, comparative testing of an identical steamer equipped with a conventional burner, and comprehensive testing of the low-NOx-burner-equipped steamer. Comprehensive test measurements included continuous flue-gas monitoring; source assessment sampling system testing with subsequent laboratory analysis to give total flue-gas organics in two boiling point ranges and specific quantitation on the semivolatile organic priority pollutants; C1 to C6 hydrocarbon sampling; Methods 5/8 sampling for particulate and SO/sub 2/ and SO/sub 3/ emissions; andmore » emitted particle size distribution tests using Andersen impactors. Full-load NOx emissions of 110 ppm (3% O/sub 2/) could be maintained from the low-NOx burner at acceptable CO and smoke emissions, compared to about 300 ppm (3% O/sub 2/) from the conventional-burner-equipped steamer. At the low-NOx condition, CO, SO/sub 2/, and SO/sub 3/ emissions were 93, 594, and 3.1 ppm, respectively. Particulate emissions were 39 mg/dscm with a mean particle diameter of 3 to 4 micrometers. Total organic emissions were 11.1 mg/dscm, almost exclusively volatile (C1 to C6) organics. Three PAHs were detected at from 0.1 to 1.4 micrograms/dscm.« less

Combination of biodiesel-ethanol-diesel fuel blend and SCR catalyst assembly to reduce emissions from a heavy-duty diesel engine.

PubMed

Shi, Xiaoyan; Yu, Yunbo; He, Hong; Shuai, Shijin; Dong, Hongyi; Li, Rulong

2008-01-01

In this study, the efforts to reduce NOx and particulate matter (PM) emissions from a diesel engine using both ethanol-selective catalytic reduction (SCR) of NOx over an Ag/Al2O3 catalyst and a biodiesel-ethanol-diesel fuel blend (BE-diesel) on an engine bench test are discussed. Compared with diesel fuel, use of BE-diesel increased PM emissions by 14% due to the increase in the soluble organic fraction (SOF) of PM, but it greatly reduced the Bosch smoke number by 60%-80% according to the results from 13-mode test of European Stationary Cycle (ESC) test. The SCR catalyst was effective in NOx reduction by ethanol, and the NOx conversion was approximately 73%. Total hydrocarbons (THC) and CO emissions increased significantly during the SCR of NOx process. Two diesel oxidation catalyst (DOC) assemblies were used after Ag/Al2O3 converter to remove CO and HC. Different oxidation catalyst showed opposite effect on PM emission. The PM composition analysis revealed that the net effect of oxidation catalyst on total PM was an integrative effect on SOF reduction and sulfate formation of PM. The engine bench test results indicated that the combination of BE-diesel and a SCR catalyst assembly could provide benefits for NOx and PM emissions control even without using diesel particle filters (DPFs).

Why do Models Overestimate Surface Ozone in the Southeastern United States?

NASA Astrophysics Data System (ADS)

Travis, K.; Jacob, D.; Fisher, J. A.; Kim, S.; Marais, E. A.; Zhu, L.; Yu, K.; Miller, C. E.; Yantosca, R.; Payer Sulprizio, M.; Thompson, A. M.; Wennberg, P. O.; Crounse, J.; St Clair, J. M.; Cohen, R. C.; Laughner, J.; Dibb, J. E.; Hall, S. R.; Ullmann, K.; Wolfe, G.; Pollack, I. B.; Peischl, J.; Neuman, J. A.; Zhou, X.

2016-12-01

Ozone pollution in the Southeast US involves complex chemistry driven by emissions of anthropogenic nitrogen oxide radicals (NOx = NO + NO2) and biogenic isoprene. Model estimates of surface ozone concentrations tend to be biased high in the region and this is of concern for designing effective emission control strategies to meet air quality standards. We use detailed chemical observations from the SEAC4RS aircraft campaign in August and September 2013, interpreted with the GEOS-Chem chemical transport model at 0.25°×0.3125° horizontal resolution, to better understand the factors controlling surface ozone in the Southeast US. We find that the National Emission Inventory (NEI) for NO­x from the US Environmental Protection Agency (EPA) is too high in the Southeast and nationally by a factor of 2. This finding is based on SEAC4RS observations of NOx and its oxidation products, surface network observations of nitrate wet deposition fluxes, and OMI satellite observations of tropospheric NO2 columns. Upper tropospheric NO2 from lightning makes a large contribution to the satellite observations that must be accounted for when using these data to estimate surface NOx emissions. We find that only half of isoprene oxidation proceeds by the high-NOx pathway to produce ozone; this fraction is only moderately sensitive to changes in NOx emissions because isoprene and NOx emissions are spatially segregated. GEOS-Chem with reduced NOx emissions provides an unbiased simulation of ozone observations from the aircraft, and reproduces the observed ozone production efficiency in the boundary layer as derived from a regression of ozone and NOx oxidation products. However, the model is still biased high by 8±13 ppb relative to observed surface ozone in the Southeast US. Ozonesondes launched during midday hours show a 7 ppb ozone decrease from 1.5 km to the surface that GEOS-Chem does not capture. This may be caused by excessively dry conditions in the model, representing another factor important in the simulation of surface ozone.

Assessment of vehicle emission programs in China during 1998-2013: Achievement, challenges and implications.

PubMed

Wu, Xiaomeng; Wu, Ye; Zhang, Shaojun; Liu, Huan; Fu, Lixin; Hao, Jiming

2016-07-01

China has been embracing rapid motorization since the 1990s, and vehicles have become one of the major sources of air pollution problems. Since the late 1990s, thanks to the international experience, China has adopted comprehensive control measures to mitigate vehicle emissions. This study employs a local emission model (EMBEV) to assess China's first fifteen-year (1998-2013) efforts in controlling vehicles emissions. Our results show that China's total annual vehicle emissions in 2013 were 4.16 million tons (Mt) of HC, 27.4 Mt of CO, 7.72 Mt of NOX, and 0.37 Mt of PM2.5, respectively. Although vehicle emissions are substantially reduced relative to the without control scenarios, we still observe significantly higher emission density in East China than in developed countries with longer histories of vehicle emission control. This study further informs China's policy-makers of the prominent challenges to control vehicle emissions in the future. First, unlike other major air pollutants, total NOX emissions have rapidly increased due to a surge of diesel trucks and the postponed China IV standard nationwide. Simultaneous implementation of fuel quality improvements and vehicle-engine emission standards will be of great importance to alleviate NOX emissions for diesel fleets. Second, the enforcement of increasingly stringent standards should include strict oversight of type-approval conformity, in-use complacence and durability, which would help reduce gross emitters of PM2.5 that are considerable among in-use diesel fleets at the present. Third, this study reveals higher HC emissions than previous results and indicates evaporative emissions may have been underestimated. Considering that China's overall vehicle ownership is far from saturation, persistent efforts are required through economic tools, traffic management and emissions regulations to lower vehicle-use intensity and limit both exhaust and evaporative emissions. Furthermore, in light of the complex technology for emerging new energy vehicles, their real-world emissions need to be adequately evaluated before massive promotion. Copyright © 2016 Elsevier Ltd. All rights reserved.

Ships going slow in reducing their NOx emissions: changes in 2005-2012 ship exhaust inferred from satellite measurements over Europe

NASA Astrophysics Data System (ADS)

Folkert Boersma, K.; Vinken, Geert C. M.; Tournadre, Jean

2015-07-01

We address the lack of temporal information on ship emissions, and report on rapid short-term variations of satellite-derived ship NOx emissions between 2005 and 2012 over European seas. Our inversion is based on OMI observed tropospheric NO2 columns and GEOS-Chem simulations. Average European ship NOx emissions increased by ˜15% from 2005 to 2008. This increase was followed by a reduction of ˜12% in 2009, a direct result of the global economic downturn in 2008-2009, and steady emissions from 2009 to 2012. Observations of ship passages through the Suez Canal and satellite altimeter derived ship densities suggests that ships in the Mediterranean Sea have reduced their speed by more than 30% since 2008. This reduction in ship speed is accompanied by a persistent 45% reduction of average, per ship NOx emission factors. Our results indicate that the practice of ‘slow steaming’, i.e. the lowering of vessel speed to reduce fuel consumption, has indeed been implemented since 2008, and can be detected from space. In spite of the implementation of slow steaming, one in seven of all NOx molecules emitted in Europe in 2012 originated from the shipping sector, up from one in nine in 2005. The growing share of the shipping contributions to the overall European NOx emissions suggests a need for the shipping sector to implement additional measures to reduce pollutant emissions at rates that are achieved by the road transport and energy producing sectors in Europe.

Emissions from Plug-in Hybrid Electric Vehicle (PHEV) During Real World Driving Under Various Weather Conditions

DOT National Transportation Integrated Search

2018-02-02

Exposure to particulate matter (PM) and pollutant gas (NOx) is associated with increased cardiopulmonary morbidity and mortality. Mobile source emissions contribute to PM and NOx emissions significantly in urban areas. Hybrid Electric Vehicles (HEVs)...

Emissions from gas fired agricultural burners

USDA-ARS?s Scientific Manuscript database

Because of the Federal Clean Air Act, the San Joaquin Valley Unified Air Pollution Control District (SJVUAPCD) began defining Best Available Control Technology (BACT) for NOx emissions from cotton gin drying system gas fired burners in its jurisdiction. The NOx emission levels of conventionally used...

The combustion of different air distribution of foursquare tangential circle boiler by numerical simulation

NASA Astrophysics Data System (ADS)

Guo, Yue; Du, Lei; Jiang, Long; Li, Qing; Zhao, Zhenning

2017-01-01

In this paper, the combustion and NOx emission characteristics of a 300 MW tangential boiler are simulated, we obtain the flue gas velocity field in the hearth, component concentration distribution of temperature field and combustion products, and the speed, temperature, concentration of oxygen and NOx emissions compared with the test results in the waisting air distribution conditions, found the simulation values coincide well with the test value, to verify the rationality of the model. At the same time, the flow field in the furnace, the combustion and the influence of NOx emission characteristics are simulated by different conditions, including compared with primary zone secondary waisting air distribution, uniform air distribution and pagodas go down air distribution, the results show that, waisting air distribution is useful to reduce NOx emissions.

Mechanisms and modeling of the effects of additives on the nitrogen oxides emission

NASA Technical Reports Server (NTRS)

Kundu, Krishna P.; Nguyen, Hung Lee; Kang, M. Paul

1991-01-01

A theoretical study on the emission of the oxides of nitrogen in the combustion of hydrocarbons is presented. The current understanding of the mechanisms and the rate parameters for gas phase reactions were used to calculate the NO(x) emission. The possible effects of different chemical species on thermal NO(x), on a long time scale were discussed. The mixing of these additives at various stages of combustion were considered and NO(x) concentrations were calculated; effects of temperatures were also considered. The chemicals such as hydrocarbons, H2, CH3OH, NH3, and other nitrogen species were chosen as additives in this discussion. Results of these calculations can be used to evaluate the effects of these additives on the NO(x) emission in the industrial combustion system.

40 CFR 75.73 - Recordkeeping and reporting.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) CONTINUOUS EMISSION MONITORING NOX Mass Emissions Provisions § 75.73 Recordkeeping and reporting... for units using the low mass emissions unit provisions of § 75.19). (3) For each hour when the unit is operating, NOX mass emissions, calculated in accordance with section 8.1 of appendix F to this part. (4...

ANALYSIS OF MOTOR VEHICLE EMISSIONS IN A HOUSTON TUNNEL DURING THE TEXAS AIR QUALITY STUDY 2000

EPA Science Inventory

Measurements from a Houston tunnel were used to develop fuel consumption based emission factors for CO, NOx, and Non-Methane Organic Compound (NMOC) for on-road gasoline vehicles. The Houston NOx emission factor was at the low range of emission factors reported in previous (pr...

High emission reduction performance of a novel organic-inorganic composite filters containing sepiolite mineral nanofibers

PubMed Central

Wang, Fei; Zhang, Hui; Liang, Jinsheng; Tang, Qingguo; Li, Yanxia; Shang, Zengyao

2017-01-01

In this work, a new organic-inorganic composite filter was prepared. The thickness, pore size, air permeability, bursting strength and microstructure were characterized systematically, proving that coatings had regulatory effect on filters physical properties. Benefitting from the distinct coatings containing 5% sepiolite nanofibers after five times dilution, the physical properties of corresponding air filter exhibits the most favorable performance and meet the standard of air filter. When used as fuel filter, it satisfies the fuel filter standard and achieves the best performance after six times dilution. The contrast test on engine emission was taken based on auto filters coated with/without as prepared nanofibers. An obvious decrease in the emission of carbon monoxide (CO), hydrocarbons (HC) and nitrogen oxide (NOx) can be observed after installation of composite filter on vehicles. Under the high idle condition, gasoline engine emission decreased by 8.13%, 11.35% and 44.91% for CO, HC and NOx, respectively. When tested in the low idle condition, engine emission reduced by 0.43%, 1.14% and 85.67% for CO, HC and NOx, respectively. The diesel engine emissions of CO, NOx and total amount of HC and NOx decreased by 32.26%, 3.28% and 4.66%, respectively. The results illustrate the composite installation exhibits satisfactory emission reduction effect. PMID:28252034

High emission reduction performance of a novel organic-inorganic composite filters containing sepiolite mineral nanofibers

NASA Astrophysics Data System (ADS)

Wang, Fei; Zhang, Hui; Liang, Jinsheng; Tang, Qingguo; Li, Yanxia; Shang, Zengyao

2017-03-01

In this work, a new organic-inorganic composite filter was prepared. The thickness, pore size, air permeability, bursting strength and microstructure were characterized systematically, proving that coatings had regulatory effect on filters physical properties. Benefitting from the distinct coatings containing 5% sepiolite nanofibers after five times dilution, the physical properties of corresponding air filter exhibits the most favorable performance and meet the standard of air filter. When used as fuel filter, it satisfies the fuel filter standard and achieves the best performance after six times dilution. The contrast test on engine emission was taken based on auto filters coated with/without as prepared nanofibers. An obvious decrease in the emission of carbon monoxide (CO), hydrocarbons (HC) and nitrogen oxide (NOx) can be observed after installation of composite filter on vehicles. Under the high idle condition, gasoline engine emission decreased by 8.13%, 11.35% and 44.91% for CO, HC and NOx, respectively. When tested in the low idle condition, engine emission reduced by 0.43%, 1.14% and 85.67% for CO, HC and NOx, respectively. The diesel engine emissions of CO, NOx and total amount of HC and NOx decreased by 32.26%, 3.28% and 4.66%, respectively. The results illustrate the composite installation exhibits satisfactory emission reduction effect.

Role of sectoral and multi-pollutant emission control strategies in improving atmospheric visibility in the Yangtze River Delta, China.

PubMed

Huang, Kan; Fu, Joshua S; Gao, Yang; Dong, Xinyi; Zhuang, Guoshun; Lin, Yanfen

2014-01-01

The Community Multi-scale Air Quality modeling system is used to investigate the response of atmospheric visibility to the emission reduction from different sectors (i.e. industries, traffic and power plants) in the Yangtze River Delta, China. Visibility improvement from exclusive reduction of NOx or VOC emission was most inefficient. Sulfate and organic aerosol would rebound if NOx emission was exclusively reduced from any emission sector. The most efficient way to improve the atmospheric visibility was proven to be the multi-pollutant control strategies. Simultaneous emission reductions (20-50%) on NOx, VOC and PM from the industrial and mobile sectors could result in 0.3-1.0 km visibility improvement. And the emission controls on both NOx (85%) and SO2 (90%) from power plants gained the largest visibility improvement of up to 4.0 km among all the scenarios. The seasonal visibility improvement subject to emission controls was higher in summer while lower in the other seasons. Copyright © 2013 Elsevier Ltd. All rights reserved.

Technology innovations and experience curves for nitrogen oxides control technologies.

PubMed

Yeh, Sonia; Rubin, Edward S; Taylor, Margaret R; Hounshell, David A

2005-12-01

This paper reviews the regulatory history for nitrogen oxides (NOx) pollutant emissions from stationary sources, primarily in coal-fired power plants. Nitrogen dioxide (NO2) is one of the six criteria pollutants regulated by the 1970 Clean Air Act where National Ambient Air Quality Standards were established to protect public health and welfare. We use patent data to show that in the cases of Japan, Germany, and the United States, innovations in NOx control technologies did not occur until stringent government regulations were in place, thus "forcing" innovation. We also demonstrate that reductions in the capital and operation and maintenance (O&M) costs of new generations of high-efficiency NOx control technologies, selective catalytic reduction (SCR), are consistently associated with the increasing adoption of the control technology: the so-called learning-by-doing phenomena. The results show that as cumulative world coal-fired SCR capacity doubles, capital costs decline to approximately 86% and O&M costs to 58% of their original values. The observed changes in SCR technology reflect the impact of technological advance as well as other factors, such as market competition and economies of scale.

Quantifying emissions of NH3 and NOx from Agricultural Sources and Biomass Burning using SOF

NASA Astrophysics Data System (ADS)

Kille, N.; Volkamer, R. M.; Dix, B. K.

2017-12-01

Column measurements of trace gas absorption along the direct solar beam present a powerful yet underused approach to quantify emission fluxes from area sources. The University of Colorado Solar Occultation Flux (CU SOF) instrument (Kille et al., 2017, AMT, doi:10.5194/amt-10-373-2017) features a solar tracker that is self-positioning for use from mobile platforms that are in motion (Baidar et al., 2016, AMT, doi: 10.5194/amt-9-963-2016). This enables the use from research aircraft, as well as the deployment under broken cloud conditions, while making efficient use of aircraft time. First airborne SOF measurements have been demonstrated recently, and we discuss applications to study emissions from biomass burning using aircraft, and to study primary emissions of ammonia and nitrogen oxides (= NO + NO2) from area sources such as concentrated animal feeding operations (CAFO). SOF detects gases in the open atmosphere (no inlets), does not require access to the source, and provides results in units that can be directly compared with emission inventories. The method of emission quantification is relatively straightforward. During FRAPPE (Front Range Air Pollution and Photochemistry Experiment) in Colorado in 2014, we measured emission fluxes of NH3, and NOx from CAFO, quantifying the emissions from 61400 of the 535766 cattle in Weld County, CO (11.4% of the cattle population). We find that NH3 emissions from dairy and cattle farms are similar after normalization by the number of cattle, i.e., we find emission factors, EF, of 11.8 ± 2.0 gNH3/h/head for the studied CAFOs; these EFs are at the upper end of reported values. Results are compared to daytime NEI emissions for case study days. Furthermore, biologically active soils are found to be a strong source of NOx. The NOx sources account for 1.2% of the N-flux (i.e., NH3), and can be competitive with other NOx sources in Weld, CO. The added NOx is particularly relevant in remote regions, where O3 formation and oxidative capacity is NOx limited.

Drive cycle simulation of high efficiency combustions on fuel economy and exhaust properties in light-duty vehicles

DOE PAGES

Gao, Zhiming; Curran, Scott J.; Parks, James E.; ...

2015-04-06

We present fuel economy and engine-out emissions for light-duty (LD) conventional and hybrid vehicles powered by conventional and high-efficiency combustion engines. Engine technologies include port fuel-injected (PFI), direct gasoline injection (GDI), reactivity controlled compression ignition (RCCI) and conventional diesel combustion (CDC). In the case of RCCI, the engine utilized CDC combustion at speed/load points not feasible with RCCI. The results, without emissions considered, show that the best fuel economies can be achieved with CDC/RCCI, with CDC/RCCI, CDC-only, and lean GDI all surpassing PFI fuel economy significantly. In all cases, hybridization significantly improved fuel economy. The engine-out hydrocarbon (HC), carbon monoxidemore » (CO), nitrogen oxides (NOx), and particulate matter (PM) emissions varied remarkably with combustion mode. The simulated engine-out CO and HC emissions from RCCI are significantly higher than CDC, but RCCI makes less NOx and PM emissions. Hybridization can improve lean GDI and RCCI cases by increasing time percentage for these more fuel efficient modes. Moreover, hybridization can dramatically decreases the lean GDI and RCCI engine out emissions. Importantly, lean GDI and RCCI combustion modes decrease exhaust temperatures, especially for RCCI, which limits aftertreatment performance to control tailpipe emissions. Overall, the combination of engine and hybrid drivetrain selected greatly affects the emissions challenges required to meet emission regulations.« less

Effect of truck operating weight on heavy-duty diesel emissions.

PubMed

Gajendran, Prakash; Clark, Nigel N

2003-09-15

Heavy-duty diesel vehicles are substantial contributors of oxides of nitrogen (NO(x)) and particulate matter (PM) while carbon monoxide and hydrocarbon (HC) emissions from diesel vehicles receive less attention. Truck emissions inventories have traditionally employed average fuel economy and engine efficiency factors to translate certification into distance-specific (g/mi) data, so that inventories do not take into account the real effects of truck operating weight on emissions. The objective of this research was to examine weight corrections for class 7 and 8 vehicles (over 26 000 lb (11 793 kg) gross vehicle weight) from a theoretical point of view and to present a collection of original data on the topic. It was found by combining an empirical equation with theoretical truck loads that the NO(x) emissions increased by approximately 54% for a doubling of test weight. Emissions data were gathered from specific tests performed using different test weights and using various test schedules, which can consist of cycles or routes. It was found experimentally that NO(x) emissions have a nearly linear correlation with vehicle weight and did not vary much from vehicle to vehicle. NO(x) emissions were also found to be insensitive to transient operation in the test schedule. The observed trends correlate well with the theory presented, and hence, the NO(x) emissions can be predicted reasonably accurately using the theory. If NO(x) data were considered in fuel-specific (g/gal) units, they did not vary with the test weight. HC emissions were found to be insensitive to the vehicle weight. CO and PM emissions were found to be a strong function of weight during transient operation. Under transient operation, the CO emissions value increased by 36% for an increase in test weight from 42 000 (19 051 kg) to 56 000 lb (25 401 kg). However, CO and PM were found to be insensitive to the vehicle weight during nearly steady-state operation.

Evaluation of advanced combustion concepts for dry NO sub x suppression with coal-derived, gaseous fuels

NASA Technical Reports Server (NTRS)

Beebe, K. W.; Symonds, R. A.; Notardonato, J. J.

1982-01-01

The emissions performance of a rich lean combustor (developed for liquid fuels) was determined for combustion of simulated coal gases ranging in heating value from 167 to 244 Btu/scf (7.0 to 10.3 MJ/NCM). The 244 Btu/scf gas is typical of the product gas from an oxygen blown gasifier, while the 167 Btu/scf gas is similar to that from an air blown gasifier. NOx performance of the rich lean combustor did not meet program goals with the 244 Btu/scf gas because of high thermal NOx, similar to levels expected from conventional lean burning combustors. The NOx emissions are attributed to inadequate fuel air mixing in the rich stage resulting from the design of the large central fuel nozzle delivering 71% of the total gas flow. NOx yield from ammonia injected into the fuel gas decreased rapidly with increasing ammonia level, and is projected to be less than 10% at NH3 levels of 0.5% or higher. NOx generation from NH3 is significant at ammonia concentrations significantly less than 0.5%. These levels may occur depending on fuel gas cleanup system design. CO emissions, combustion efficiency, smoke and other operational performance parameters were satisfactory. A test was completed with a catalytic combustor concept with petroleum distillate fuel. Reactor stage NOx emissions were low (1.4g NOx/kg fuel). CO emissions and combustion efficiency were satisfactory. Airflow split instabilities occurred which eventually led to test termination.

Investigating the microbial community responsible for unusually high soil N2O and NOx emissions in the Colorado Desert

NASA Astrophysics Data System (ADS)

Eberwein, J. R.; Carey, C.; Aronson, E. L.; Jenerette, D.

2016-12-01

Although the importance of soil nitrogenous emissions are well accepted in terms of local and global ecological relevance, there remain considerable knowledge gaps concerning the mechanisms regulating production, particularly in arid systems. This study aimed to connect desert soil trace gas emissions of nitrous oxide (N2O) and nitrogen oxides (NOx) with compositional changes in the microbial community. We quantified real-time soil trace gas emissions at two sites in the Colorado Desert experiencing contrasting anthropogenic nitrogen (N) deposition loads (<5 and 15 kg N ha-1 y-1). Measurements were made through 48 hours following water (to simulate a 2 cm rain event) and N additions (at 30 kg NH4NO3 ha-1). In conjunction with flux measurements, soil samples were collected for 16S rRNA gene sequencing to characterize the soil microbial community. N2O fluxes reached as high as 1200 ng N2O-N m-2 s-1, well above most published emissions, but returned to pre-wetting conditions within 12 hours. NOx emissions reached as high as 350 ng NOx-N m-2 s-1 and remained elevated past 24 hours post-wetting. Results from the 16S analysis indicate distinct differences in the microbial community composition between the high and low N deposition sites, with less than 50% of operational taxonomic units (OTUs) in common between sites. N addition had a significant effect on the soil microbial community at the low deposition site, but not at the high deposition site. Furthermore, significant shifts in the bacterial community occurred after wetting, with only one third of the community remaining constant between time points. These results suggest that gaseous N export, particularly N2O emission, is a greater form of nitrogen loss in this system than is currently assumed. Experimental N additions and anthropogenic N deposition show potential for shifting soil microbial community composition, with implications for soil N emissions. Furthermore, shifts in the microbial community can occur as quickly as 15 minutes post-wetting, representing a remarkable ability for soil microorganisms to recover from extreme water stress. As aridlands cover approximately one third of the Earth's land surface, understanding the mechanisms that contribute to soil N emissions in these systems is of important global relevance.

MOVES2014: Heavy-duty Vehicle Emissions Report

EPA Science Inventory

This report updates MOVES methods for evaluating current HD diesel NOx emission rates based on comparisons to independent data from EPA’s IUVP and Houston drayage programs. The report also details methods/assumptions made for HD gasoline HC, CO and NOx emission rates using reduct...

Final Rule for Control of Air Pollution from Aircraft and Aircraft Engines: Emission Standards and Test Procedures

EPA Pesticide Factsheets

EPA is amending the existing emission standards for oxides of nitrogen (NOx) for new commercial aircraft engines. These standards are equivalent to the NOx emission standards of the United Nations International Civil Aviation Organization (ICAO).

Low modeled ozone production suggests underestimation of precursor emissions (especially NOx) in Europe

NASA Astrophysics Data System (ADS)

Oikonomakis, Emmanouil; Aksoyoglu, Sebnem; Ciarelli, Giancarlo; Baltensperger, Urs; Prévôt, André Stephan Henry

2018-02-01

High surface ozone concentrations, which usually occur when photochemical ozone production takes place, pose a great risk to human health and vegetation. Air quality models are often used by policy makers as tools for the development of ozone mitigation strategies. However, the modeled ozone production is often not or not enough evaluated in many ozone modeling studies. The focus of this work is to evaluate the modeled ozone production in Europe indirectly, with the use of the ozone-temperature correlation for the summer of 2010 and to analyze its sensitivity to precursor emissions and meteorology by using the regional air quality model, the Comprehensive Air Quality Model with Extensions (CAMx). The results show that the model significantly underestimates the observed high afternoon surface ozone mixing ratios (≥ 60 ppb) by 10-20 ppb and overestimates the lower ones (< 40 ppb) by 5-15 ppb, resulting in a misleading good agreement with the observations for average ozone. The model also underestimates the ozone-temperature regression slope by about a factor of 2 for most of the measurement stations. To investigate the impact of emissions, four scenarios were tested: (i) increased volatile organic compound (VOC) emissions by a factor of 1.5 and 2 for the anthropogenic and biogenic VOC emissions, respectively, (ii) increased nitrogen oxide (NOx) emissions by a factor of 2, (iii) a combination of the first two scenarios and (iv) increased traffic-only NOx emissions by a factor of 4. For southern, eastern, and central (except the Benelux area) Europe, doubling NOx emissions seems to be the most efficient scenario to reduce the underestimation of the observed high ozone mixing ratios without significant degradation of the model performance for the lower ozone mixing ratios. The model performance for ozone-temperature correlation is also better when NOx emissions are doubled. In the Benelux area, however, the third scenario (where both NOx and VOC emissions are increased) leads to a better model performance. Although increasing only the traffic NOx emissions by a factor of 4 gave very similar results to the doubling of all NOx emissions, the first scenario is more consistent with the uncertainties reported by other studies than the latter, suggesting that high uncertainties in NOx emissions might originate mainly from the road-transport sector rather than from other sectors. The impact of meteorology was examined with three sensitivity tests: (i) increased surface temperature by 4 °C, (ii) reduced wind speed by 50 % and (iii) doubled wind speed. The first two scenarios led to a consistent increase in all surface ozone mixing ratios, thus improving the model performance for the high ozone values but significantly degrading it for the low ozone values, while the third scenario had exactly the opposite effects. Overall, the modeled ozone is predicted to be more sensitive to its precursor emissions (especially traffic NOx) and therefore their uncertainties, which seem to be responsible for the model underestimation of the observed high ozone mixing ratios and ozone production.

High Pressure Low NOx Emissions Research: Recent Progress at NASA Glenn Research Center

NASA Technical Reports Server (NTRS)

Chi-Ming, Lee; Tacina, Kathleen M.; Wey, Changlie

2007-01-01

In collaboration with U.S. aircraft engine companies, NASA Glenn Research Center has contributed to the advancement of low emissions combustion systems. For the High Speed Research Program (HSR), a 90% reduction in nitrogen oxides (NOx) emissions (relative to the then-current state of the art) has been demonstrated in sector rig testing at General Electric Aircraft Engines (GEAE). For the Advanced Subsonic Technology Program (AST), a 50% reduction in NOx emissions relative to the 1996 International Civil Aviation Organization (ICAO) standards has been at demonstrated in sector rigs at both GEAE and Pratt & Whitney (P&W). During the Ultra Efficient Engine Technology Program (UEET), a 70% reduction in NOx emissions, relative to the 1996 ICAO standards, was achieved in sector rig testing at Glenn in the world class Advanced Subsonic Combustion Rig (ASCR) and at contractor facilities. Low NOx combustor development continues under the Fundamental Aeronautics Program. To achieve these reductions, experimental and analytical research has been conducted to advance the understanding of emissions formation in combustion processes. Lean direct injection (LDI) concept development uses advanced laser-based non-intrusive diagnostics and analytical work to complement the emissions measurements and to provide guidance for concept improvement. This paper describes emissions results from flametube tests of a 9- injection-point LDI fuel/air mixer tested at inlet pressures up to 5500 kPa. Sample results from CFD and laser diagnostics are also discussed.

NASA Glenn High Pressure Low NOx Emissions Research

NASA Technical Reports Server (NTRS)

Tacina, Kathleen M.; Wey, Changlie

2008-01-01

In collaboration with U.S. aircraft engine companies, NASA Glenn Research Center has contributed to the advancement of low emissions combustion systems. For the High Speed Research Program (HSR), a 90% reduction in nitrogen oxides (NOx) emissions (relative to the then-current state of the art) has been demonstrated in sector rig testing at General Electric Aircraft Engines (GEAE). For the Advanced Subsonic Technology Program (AST), a 50% reduction in NOx emissions relative to the 1996 International Civil Aviation Organization (ICAO) standards has been demonstrated in sector rigs at both GEAE and Pratt & Whitney (P&W). During the Ultra Efficient Engine Technology Program (UEET), a 70% reduction in NOx emissions, relative to the 1996 ICAO standards, was achieved in sector rig testing at Glenn in the world class Advanced Subsonic Combustion Rig (ASCR) and at contractor facilities. Low NOx combustor development continues under the Fundamental Aeronautics Program. To achieve these reductions, experimental and analytical research has been conducted to advance the understanding of emissions formation in combustion processes. Lean direct injection (LDI) concept development uses advanced laser-based non-intrusive diagnostics and analytical work to complement the emissions measurements and to provide guidance for concept improvement. This paper describes emissions results from flametube tests of a 9-injection-point LDI fuel/air mixer tested at inlet pressures up to 5500 kPa. Sample results from CFD and laser diagnostics are also discussed.

Trends in multi-pollutant emissions from a technology-linked inventory for India: I. Industry and transport sectors

NASA Astrophysics Data System (ADS)

Sadavarte, Pankaj; Venkataraman, Chandra

2014-12-01

Emissions estimation, for research and regulatory applications including reporting to international conventions, needs treatment of detailed technology divisions and high-emitting technologies. Here we estimate Indian emissions, for 1996-2015, of aerosol constituents (PM2.5, BC and OC) and precursor gas SO2, ozone precursors (CO, NOx, NMVOC and CH4) and greenhouse gases (CO2 and N2O), using a common fuel consumption database and consistent assumptions. Six source categories and 45 technologies/activities in the industry and transport sectors were used for estimating emissions for 2010. Mean emission factors, developed at the source-category level, were used with corresponding fuel consumption data, available for 1996-2011, projected to 2015. New activities were included to account for fugitive emissions of NMVOC from chemical and petrochemical industries. Dynamic emission factors, reflecting changes in technology-mix and emission regulations, were developed for thermal power plants and on-road transport vehicles. Modeled emission factors were used for gaseous pollutants for on-road vehicles. Emissions of 2.4 (0.6-7.5) Tg y-1 PM2.5, 0.23 (0.1-0.7) Tg y-1 BC, 0.15 (0.04-0.5) Tg y-1 OC, 7.3 (6-10) Tg y-1 SO2, 19 (7.5-33) Tg y-1 CO, 1.5 (0.1-9) Tg y-1 CH4, 4.3 (2-9) Tg y-1 NMVOC, 5.6 (1.7-15.9) Tg y-1 NOx, 1750 (1397-2231) Tg y-1 CO2 and 0.13 (0.05-0.3) Tg y-1 N2O were estimated for 2015. Significant emissions of aerosols and their precursors were from coal use in thermal power and industry (PM2.5 and SO2), and on-road diesel vehicles (BC), especially superemitters. Emissions of ozone precursors were largely from thermal power plants (NOx), on-road gasoline vehicles (CO and NMVOC) and fugitive emissions from mining (CH4). Highly uncertain default emission factors were the principal contributors to uncertainties in emission estimates, indicating the need for region specific measurements.

Top-down estimate of surface flux in the Los Angeles Basin using a mesoscale inverse modeling technique: assessing anthropogenic emissions of CO, NOx and CO2 and their impacts

NASA Astrophysics Data System (ADS)

Brioude, J.; Angevine, W. M.; Ahmadov, R.; Kim, S.-W.; Evan, S.; McKeen, S. A.; Hsie, E.-Y.; Frost, G. J.; Neuman, J. A.; Pollack, I. B.; Peischl, J.; Ryerson, T. B.; Holloway, J.; Brown, S. S.; Nowak, J. B.; Roberts, J. M.; Wofsy, S. C.; Santoni, G. W.; Oda, T.; Trainer, M.

2013-04-01

We present top-down estimates of anthropogenic CO, NOx and CO2 surface fluxes at mesoscale using a Lagrangian model in combination with three different WRF model configurations, driven by data from aircraft flights during the CALNEX campaign in southern California in May-June 2010. The US EPA National Emission Inventory 2005 (NEI 2005) was the prior in the CO and NOx inversion calculations. The flux ratio inversion method, based on linear relationships between chemical species, was used to calculate the CO2 inventory without prior knowledge of CO2 surface fluxes. The inversion was applied to each flight to estimate the variability of single-flight-based flux estimates. In Los Angeles (LA) County, the uncertainties on CO and NOx fluxes were 10% and 15%, respectively. Compared with NEI 2005, the CO posterior emissions were lower by 43% in LA County and by 37% in the South Coast Air Basin (SoCAB). NOx posterior emissions were lower by 32% in LA County and by 27% in the SoCAB. NOx posterior emissions were 40% lower on weekends relative to weekdays. The CO2 posterior estimates were 183 Tg yr-1 in SoCAB. A flight during ITCT (Intercontinental Transport and Chemical Transformation) in 2002 was used to estimate emissions in the LA Basin in 2002. From 2002 to 2010, the CO and NOx posterior emissions decreased by 41% and 37%, respectively, in agreement with previous studies. Over the same time period, CO2 emissions increased by 10% in LA County but decreased by 4% in the SoCAB, a statistically insignificant change. Overall, the posterior estimates were in good agreement with the California Air Resources Board (CARB) inventory, with differences of 15% or less. However, the posterior spatial distribution in the basin was significantly different from CARB for NOx emissions. WRF-Chem mesoscale chemical-transport model simulations allowed an evaluation of differences in chemistry using different inventory assumptions, including NEI 2005, a gridded CARB inventory and the posterior inventories derived in this study. The biases in WRF-Chem ozone were reduced and correlations were increased using the posterior from this study compared with simulations with the two bottom-up inventories, suggesting that improving the spatial distribution of ozone precursor surface emissions is also important in mesoscale chemistry simulations.

Nitrogen stable isotope composition (δ15N) of vehicle-emitted NOx.

PubMed

Walters, Wendell W; Goodwin, Stanford R; Michalski, Greg

2015-02-17

The nitrogen stable isotope ratio of NOx (δ(15)N-NOx) has been proposed as a regional indicator for NOx source partitioning; however, knowledge of δ(15)N values from various NOx emission sources is limited. This study presents a detailed analysis of δ(15)N-NOx emitted from vehicle exhaust, the largest source of anthropogenic NOx. To accomplish this, NOx was collected from 26 different vehicles, including gasoline and diesel-powered engines, using a modification of a NOx collection method used by the United States Environmental Protection Agency, and δ(15)N-NOx was analyzed. The vehicles sampled in this study emitted δ(15)N-NOx values ranging from -19.1 to 9.8‰ that negatively correlated with the emitted NOx concentrations (8.5 to 286 ppm) and vehicle run time because of kinetic isotope fractionation effects associated with the catalytic reduction of NOx. A model for determining the mass-weighted δ(15)N-NOx from vehicle exhaust was constructed on the basis of average commute times, and the model estimates an average value of -2.5 ± 1.5‰, with slight regional variations. As technology improvements in catalytic converters reduce cold-start emissions in the future, it is likely to increase current δ(15)N-NOx values emitted from vehicles.

Effect of inlet-air humidity, temperature, pressure, and reference Mach number on the formation of oxides of nitrogen in a gas turbine combustor

NASA Technical Reports Server (NTRS)

Marchionna, N. R.; Diehl, L. A.; Trout, A. M.

1973-01-01

Tests were conducted to determine the effect of inlet air humidity on the formation of oxides of nitrogen (NOx) from a gas turbine combustor. Combustor inlet air temperature ranged from 506 K (450 F) to 838 K (1050 F). The tests were primarily run at a constant pressure of 6 atmospheres and reference Mach number of 0.065. The NOx emission index was found to decrease with increasing inlet air humidity at a constant exponential rate: NOx = NOx0e-19H (where H is the humidity and the subscript 0 denotes the value at zero humidity). the emission index increased exponentially with increasing normalized inlet air temperature to the 1.14 power. Additional tests made to determine the effect of pressure and reference Mach number on NOx showed that the NOx emission index varies directly with pressure to the 0.5 power and inversely with reference Mach number.

Ozone response to emission reductions in the southeastern United States

NASA Astrophysics Data System (ADS)

Blanchard, Charles L.; Hidy, George M.

2018-06-01

Ozone (O3) formation in the southeastern US is studied in relation to nitrogen oxide (NOx) emissions using long-term (1990s-2015) surface measurements of the Southeastern Aerosol Research and Characterization (SEARCH) network, U.S. Environmental Protection Agency (EPA) O3 measurements, and EPA Clean Air Status and Trends Network (CASTNET) nitrate deposition data. Annual fourth-highest daily peak 8 h O3 mixing ratios at EPA monitoring sites in Georgia, Alabama, and Mississippi exhibit statistically significant (p < 0.0001) linear correlations with annual NOx emissions in those states between 1996 and 2015. The annual fourth-highest daily peak 8 h O3 mixing ratios declined toward values of ˜ 45-50 ppbv and monthly O3 maxima decreased at rates averaging ˜ 1-1.5 ppbv yr-1. Mean annual total oxidized nitrogen (NOy) mixing ratios at SEARCH sites declined in proportion to NOx emission reductions. CASTNET data show declining wet and dry nitrate deposition since the late 1990s, with total (wet plus dry) nitrate deposition fluxes decreasing linearly in proportion to reductions of NOx emissions by ˜ 60 % in Alabama and Georgia. Annual nitrate deposition rates at Georgia and Alabama CASTNET sites correspond to 30 % of Georgia emission rates and 36 % of Alabama emission rates, respectively. The fraction of NOx emissions lost to deposition has not changed. SEARCH and CASTNET sites exhibit downward trends in mean annual nitric acid (HNO3) concentrations. Observed relationships of O3 to NOz (NOy-NOx) support past model predictions of increases in cycling of NO and increasing responsiveness of O3 to NOx. The study data provide a long-term record that can be used to examine the accuracy of process relationships embedded in modeling efforts. Quantifying observed O3 trends and relating them to reductions in ambient NOy species concentrations offers key insights into processes of general relevance to air quality management and provides important information supporting strategies for reducing O3 mixing ratios.

Advanced Low Emissions Subsonic Combustor Study

NASA Technical Reports Server (NTRS)

Smith, Reid

1998-01-01

Recent advances in commercial and military aircraft gas turbines have yielded significant improvements in fuel efficiency and thrust-to-weight ratio, due in large part to increased combustor operating pressures and temperatures. However, the higher operating conditions have increased the emission of oxides of nitrogen (NOx), which is a pollutant with adverse impact on the atmosphere and environment. Since commercial and military aircraft are the only important direct source of NOx emissions at high altitudes, there is a growing consensus that considerably more stringent limits on NOx emissions will be required in the future for all aircraft. In fact, the regulatory communities have recently agreed to reduce NOx limits by 20 percent from current requirements effective in 1996. Further reductions at low altitude, together with introduction of limits on NOx at altitude, are virtual certainties. In addition, the U.S. Government recently conducted hearings on the introduction of federal fees on the local emission of pollutants from all sources, including aircraft. While no action was taken regarding aircraft in this instance, the threat of future action clearly remains. In these times of intense and growing international competition, the U.S. le-ad in aerospace can only be maintained through a clear technological dominance that leads to a product line of maximum value to the global airline customer. Development of a very low NOx combustor will be essential to meet the future needs of both the commercial and military transport markets, if additional economic burdens and/or operational restrictions are to be avoided. In this report, Pratt & Whitney (P&W) presents the study results with the following specific objectives: Development of low-emissions combustor technologies for advances engines that will enter into service circa 2005, while producing a goal of 70 percent lower NOx emissions, compared to 1996 regulatory levels. Identification of solution approaches to barriers to the productization and economic viability of the low-emissions technologies. Preparation of these technologies to facilitate an annular rig high-pressure demonstration.

Airborne Flux Measurements of Volatile Organic Compounds and NOx over a European megacity

NASA Astrophysics Data System (ADS)

Shaw, Marvin; Lee, James; Davison, Brian; Misztal, Pawel; Karl, Thomas; Hewitt, Nick; Lewis, Alistair

2014-05-01

Ground level ozone (O3) and nitrogen dioxide (NO2) are priority pollutants whose concentrations are closely regulated by European Union Air Quality Directive 2008/50/EC. O3 is a secondary pollutant, produced from a complex chemical interplay between oxides of nitrogen (NOx = NO + NO2) and volatile organic compounds (VOCs). Whilst the basic atmospheric chemistry leading to O3 formation is generally well understood, there are substantial uncertainties associated with the magnitude of emissions of both VOCs and NOx. At present our knowledge of O3 precursor emissions in the UK is primarily derived from National Atmospheric Emission inventories (NAEI) that provide spatially disaggregated estimates at 1x1km resolution, and these are not routinely tested at city or regional scales. Uncertainties in emissions propagate through into uncertainties in predictions of air quality in the future, and hence the likely effectiveness of control policies on both background and peak O3 and NO2 concentrations in the UK. The Ozone Precursor Fluxes in the Urban Environment (OPFUE) project aims to quantify emission rates for NOx and selected VOCs in and around the megacity of London using airborne eddy covariance (AEC). The mathematical foundation for AEC has been extensively reviewed and AEC measurements of ozone, dimethyl sulphide, CO2 and VOCs have been previously reported. During the summer of 2013, approximately 30 hours of airborne flux measurements of toluene, benzene, NO and NO2 were obtained from the NERC Airborne Research and Survey Facility's (ARSF) Dornier-228 aircraft. Over SE England, flights involved repeated south west to north east transects of ~50 km each over Greater London and it's surrounding suburbs and rural areas, flying at the aircraft's minimum operating flight altitude and airspeed (~300m, 80m/s). Mixing ratios of benzene and toluene were acquired at 2Hz using a proton transfer reaction mass spectrometer (PTR-MS) and compared to twice hourly whole air canister samples (WAS) which were quantitatively determined post-flight via TD-GCMS. Mixing ratios between the PTR-MS and WAS-TD-GCMS were in good agreement with R2 values of 0.8 and 1.0 for Toluene and Benzene respectively. Mixing ratios of NO and NO2 were acquired at 10Hz using a 2 channel NOx chemiluminescence detector with photolytic converter. These measurements were used with 20 Hz 3-D wind vector data from an AIMMS-20 turbulence probe on the aircraft to calculate highly spatially resolved (1 km) surface-to-atmosphere emission flux rates of these compounds using the eddy covariance method of Karl et al. (2013). Measured surface to atmosphere emission fluxes of NOx, benzene and toluene from London were between 40 - 91 mg m2 h-1, 0.1 - 0.4 mg m2 h-1 and 0.2 - 2 mg m2 h-1 respectively, showing the spatial flux heterogeneity over the city. This demonstrates for the first time the feasibility of airborne eddy covariance flux measurements of reactive NOx species. We also show the applicability of wavelet analysis using virtually disjunct eddy covariance measurements of anthropogenic compounds in estimating regional fluxes over a European megacity. We compare our measured emission rates with those estimated from 'bottom-up' emissions inventories and highlight the agreement between the two.

40 CFR 75.1 - Purpose and scope.

Code of Federal Regulations, 2010 CFR

2010-07-01

...), and carbon dioxide (CO2) emissions, volumetric flow, and opacity data from affected units under the... monitoring, recordkeeping, and reporting of NOX mass emissions with which EPA, individual States, or groups of States may require sources to comply in order to demonstrate compliance with a NOX mass emission...

Assessing the Parameterization of Nitric Oxide Emissions By Lightning in a Chemical Transport Model with Nitric Acid Columns from the IASI Satellite Instrument

NASA Astrophysics Data System (ADS)

Cooper, M.; Martin, R.; Wespes, C.; Coheur, P. F.; Clerbaux, C.; Murray, L. T.

2014-12-01

Nitrogen oxides (NOx ≡ NO + NO2) in the free troposphere largely control the production of ozone (O3), an important greenhouse gas and atmospheric oxidant. As HNO3 is the dominant sink of tropospheric NOx, improved understanding of its production and loss mechanisms can help to better constrain NOx emissions, and in turn improve understanding of ozone production and its effect on climate. However, this understanding is inhibited by the scarcity of direct measurements of free tropospheric HNO3, particularly in the tropics. We interpret tropical tropospheric nitric acid columns from the IASI satellite instrument with a global chemical transport model (GEOS-Chem). Overall GEOS-Chem generally agrees with IASI, however we find that the simulation underestimates IASI nitric acid over Southeast Asia by a factor of two. The bias is confirmed by comparing the GEOS-Chem simulation with additional satellite (HIRDLS, ACE-FTS) and aircraft (PEM-Tropics A and PEM-West B) observations of the middle and upper troposphere. We show that this bias can be explained by the parameterization of lightning NOx emissions, primarily from the misrepresentation of concentrated subgrid lightning NOx plumes. We tested a subgrid lightning plume parameterization and found that an additional 0.5 Tg N with an ozone production efficiency of 15 mol/mol would reduce the regional nitric acid bias from 92% to 6% without perturbing the rest of the tropics. Other sensitivity studies such as modified NOx yield per flash, increased altitude of lightning NOx emissions, or changes to convective mass flux or wet deposition of nitric acid required unrealistic changes to reduce the bias. This work demonstrates the importance of a comprehensive lightning parameterization to constraining NOx emissions.

Evaluation of a Fuel-Based Oil and Gas Inventory of Nitrogen Oxides with Top-Down Emissions

NASA Astrophysics Data System (ADS)

Mcdonald, B. C.; Gorchov Negron, A.; McKeen, S. A.; Peischl, J.; Gilman, J.; Ahmadov, R.; Frost, G. J.; Ryerson, T. B.; Thompson, C. R.; Trainer, M.

2017-12-01

Several studies have highlighted overestimates in anthropogenic emissions of nitrogen oxides (NOx) for the U.S., with particular attention on the mobile source sector. In this study, we explore whether there could be overestimates in the emissions of NOx from oil and gas production regions. We construct a bottom-up inventory using publicly available fuel use records of the industry and emission factors reported in the literature. We compare both the NEI 2011 and the fuel-based inventory with top-down emission fluxes derived by aircraft and ground-based field measurement campaigns by NOAA that occurred in 2012-13, including for basins located in Uintah, Haynesville, Marcellus, and Fayetteville. Compared to the top-down fluxes, the NEI overestimates NOx by a factor of 2 across the four basins. However, the discrepancies are not uniform, reflecting variability in oil and gas engine activity and NOx emission factors. We explore this variability with our fuel-based inventory and perform a Monte Carlo analysis to assess uncertainties in emissions. We find that on average the fuel-based inventory improves the agreement with the top-down emissions, and that the top-down emissions are within the uncertainties of our analysis.

Spatially Resolved Emissions of NOx and VOCs and Comparison to Inventories.

NASA Astrophysics Data System (ADS)

Vaughan, A. R.; Lee, J. D.; Lewis, A. C.; Shaw, M.; Purvis, R.; Carslaw, D.; Hewitt, C. N.; Misztal, P. K.; Metzger, S.; Beevers, S.; Goldstein, A. H.; Karl, T.; Davison, B.

2015-12-01

Recent trends in ambient concentrations of NOx in the UK (and other European countries) have shown a general decrease over the period 1990 to 2002, followed by largely static concentrations from 2004 - present. This is not in line with the decreases predicted based on bottom up emission inventories and has lead to widespread non-compliance with EU Air Quality Directives. We present a method to quantify the geographic variability of emission of NOx and selected VOCs at a city scale (London) using an aircraft platform. High frequency observations of NOx and VOCs (10 Hz and 2 Hz, respectively) were made using low altitude flights across London and combined with 20 Hz micro-meteorological data to provide an emission flux using the aircraft eddy covariance technique. A continuous wavelet transformation was used to produce instantaneous fluxes along the flight transect and a parameterisation of a backward Lagrangian model used to calculate the flux footprint, attributing emission rates to specific areas in Greater London (see figure). The observed flux was compared to the UK National Atmospheric Emission Inventory (NAEI), which takes a "bottom up" approach to calculating emissions, involving estimates from different source sectors to produce yearly emission estimates. These were then modified using factors specific to each source to reflect the actual month, day and time of the flight, to provide a more meaningful comparison to the observation. A significant underestimation in the inventory NOx was observed ranging from 150-200% in outer London, to 300% in the central area. Potential reasons for this are discussed, including the poor treatment of real world emissions of NOx from diesel vehicles in the inventory. We also compare measurements to the London Atmospheric Emissions Inventory (LAEI), which provides a more explicit treatment of the traffic emissions specific to London and which shows better agreement with the measurements.

Evaluating BC and NOx emission inventories for the Paris region from MEGAPOLI aircraft measurements

NASA Astrophysics Data System (ADS)

Petetin, H.; Beekmann, M.; Colomb, A.; Denier van der Gon, H. A. C.; Dupont, J.-C.; Honoré, C.; Michoud, V.; Morille, Y.; Perrussel, O.; Schwarzenboeck, A.; Sciare, J.; Wiedensohler, A.; Zhang, Q. J.

2015-09-01

High uncertainties affect black carbon (BC) emissions, and, despite its important impact on air pollution and climate, very few BC emissions evaluations are found in the literature. This paper presents a novel approach, based on airborne measurements across the Paris, France, plume, developed in order to evaluate BC and NOx emissions at the scale of a whole agglomeration. The methodology consists in integrating, for each transect, across the plume observed and simulated concentrations above background. This allows for several error sources (e.g., representativeness, chemistry, plume lateral dispersion) to be minimized in the model used. The procedure is applied with the CHIMERE chemistry-transport model to three inventories - the EMEP inventory and the so-called TNO and TNO-MP inventories - over the month of July 2009. Various systematic uncertainty sources both in the model (e.g., boundary layer height, vertical mixing, deposition) and in observations (e.g., BC nature) are discussed and quantified, notably through sensitivity tests. Large uncertainty values are determined in our results, which limits the usefulness of the method to rather strongly erroneous emission inventories. A statistically significant (but moderate) overestimation is obtained for the TNO BC emissions and the EMEP and TNO-MP NOx emissions, as well as for the BC / NOx emission ratio in TNO-MP. The benefit of the airborne approach is discussed through a comparison with the BC / NOx ratio at a ground site in Paris, which additionally suggests a spatially heterogeneous error in BC emissions over the agglomeration.

On-road assessment of light duty vehicles in Delhi city: Emission factors of CO, CO2 and NOX

NASA Astrophysics Data System (ADS)

Jaiprakash; Habib, Gazala

2018-02-01

This study presents the technology based emission factors of gaseous pollutants (CO, CO2, and NOX) measured during on-road operation of nine passenger cars of diesel, gasoline, and compressed natural gas (CNG). The emissions from two 3-wheelers, and three 2-wheelers were measured by putting the vehicles on jacks and operating them according to Modified Indian Driving Cycle (MIDC) at no load condition. The emission factors observed in the present work were significantly higher than values reported from dynamometer study by Automotive Research Association of India (ARAI). Low CO (0.34 ± 0.08 g km-1) and high NOX (1.0 ± 0.4 g km-1) emission factors were observed for diesel passenger cars, oppositely high CO (2.2 ± 2.6 g km-1) and low NOX (1.0 ± 1.6 g km-1) emission factors were seen for gasoline powered cars. The after-treatment technology in diesel vehicles was effective in CO reduction. While the use of turbocharger in diesel vehicles to generate high combustion temperature and pressure produces more NOx, probably which may not be effectively controlled by after-treatment device. The after-treatment devices in gasoline powered Post-2010, Post-2005 vehicles can be acclaimed for reduced CO emissions compared to Post-2000 vehicles. This work presents a limited data set of emission factors from on-road operations of light duty vehicles, this limitation can be improved by further measurements of emissions from similar vehicles.

Characterization of Industrial Emission Sources and Photochemistry in Houston, Texas

NASA Astrophysics Data System (ADS)

Washenfelder, R. A.; Atlas, E. L.; Degouw, J.; Flocke, F. M.; Fried, A.; Frost, G. J.; Holloway, J.; Richter, D.; Ryerson, T. B.; Schauffler, S.; Trainer, M.; Walega, J.; Warneke, C.; Weibring, P.; Zheng, W.

2009-12-01

The Houston-Galveston urban area contains a number of large industrial petrochemical emission sources that produce volatile organic compounds and nitrogen oxides. These co-located emissions result in rapid and efficient ozone production downwind. Unlike a single large power plant, the industrial complexes consist of numerous sources that can be difficult to quantify in emission inventories. During September - October 2006, the NOAA WP-3 aircraft conducted research flights as part of the second Texas Air Quality Study (TexAQS II). We examine measurements of NOx, SO2, and speciated hydrocarbons from the Houston Ship Channel, which contains a dense concentration of industrial petrochemical sources, and isolated petrochemical facilities. These measurements are used to derive source emission estimates, which are then compared to available emission inventories. We find that high hydrocarbon emissions are typical for the Houston Ship Channel and isolated petrochemical facilities. Ethene and propene are found to be major contributors to ozone formation. Ratios of C2H4 / NOx and C3H6 / NOx exceed emission inventory values by factors of 10 - 50. These findings are consistent with the first TexAQS study in 2000. We examine trends in C2H4 / NOx and C3H6 / NOx ratios between 2000 and 2006, and determine that day-to-day variability and within-plume variability exceeds any long-term reduction in ethene and propene emissions for the isolated petrochemical sources. We additionally examine downwind photochemical products formed by these alkenes.

Effect of air-staging on anthracite combustion and NOx formation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weidong Fan; Zhengchun Lin; Youyi Li

Experiments were carried out in a multipath air inlet one-dimensional furnace to assess NOx emission characteristics of the staged combustion of anthracite coal. These experiments allowed us to study the impact of pulverized coal fineness and burnout air position on emission under both deep and shallow air-staged combustion conditions. We also studied the impact of char-nitrogen release on both the burning-out process of the pulverized coal and the corresponding carbon content in fly ash. We found that air-staged combustion affects a pronounced reduction in NOx emissions from the combustion of anthracite coal. The more the air is staged, the moremore » NOx emission is reduced. In shallow air-staged combustion (f{sub M} = 0.85), the fineness of the pulverized coal strongly influences emissions, and finer coals result in lower emissions. Meanwhile, the burnout air position has only a weak effect. In the deep air-staged combustion (f{sub M} = 0.6), the effect of coal fineness is smaller, and the burnout air position has a stronger effect. When the primary combustion air is stable, NOx emissions increase with increasing burnout air. This proves that, in the burnout zone, coal char is responsible for the discharge of fuel-nitrogen that is oxidized to NOx. The measurement of secondary air staging in a burnout zone can help inhibit the oxidization of NO caused by nitrogen release. Air-staged combustion has little effect on the burnout of anthracite coal, which proves to be suitable for air-staged combustion. 31 refs., 11 figs., 1 tab.« less

Inverse Modeling of Texas NOx Emissions Using Space-Based and Ground-Based NO2 Observations

NASA Technical Reports Server (NTRS)

Tang, Wei; Cohan, D.; Lamsal, L. N.; Xiao, X.; Zhou, W.

2013-01-01

Inverse modeling of nitrogen oxide (NOx) emissions using satellite-based NO2 observations has become more prevalent in recent years, but has rarely been applied to regulatory modeling at regional scales. In this study, OMI satellite observations of NO2 column densities are used to conduct inverse modeling of NOx emission inventories for two Texas State Implementation Plan (SIP) modeling episodes. Addition of lightning, aircraft, and soil NOx emissions to the regulatory inventory narrowed but did not close the gap between modeled and satellite observed NO2 over rural regions. Satellitebased top-down emission inventories are created with the regional Comprehensive Air Quality Model with extensions (CAMx) using two techniques: the direct scaling method and discrete Kalman filter (DKF) with Decoupled Direct Method (DDM) sensitivity analysis. The simulations with satellite-inverted inventories are compared to the modeling results using the a priori inventory as well as an inventory created by a ground-level NO2 based DKF inversion. The DKF inversions yield conflicting results: the satellite based inversion scales up the a priori NOx emissions in most regions by factors of 1.02 to 1.84, leading to 3-55% increase in modeled NO2 column densities and 1-7 ppb increase in ground 8 h ozone concentrations, while the ground-based inversion indicates the a priori NOx emissions should be scaled by factors of 0.34 to 0.57 in each region. However, none of the inversions improve the model performance in simulating aircraft-observed NO2 or ground-level ozone (O3) concentrations.

Inverse modeling of Texas NOx emissions using space-based and ground-based NO2 observations

NASA Astrophysics Data System (ADS)

Tang, W.; Cohan, D. S.; Lamsal, L. N.; Xiao, X.; Zhou, W.

2013-11-01

Inverse modeling of nitrogen oxide (NOx) emissions using satellite-based NO2 observations has become more prevalent in recent years, but has rarely been applied to regulatory modeling at regional scales. In this study, OMI satellite observations of NO2 column densities are used to conduct inverse modeling of NOx emission inventories for two Texas State Implementation Plan (SIP) modeling episodes. Addition of lightning, aircraft, and soil NOx emissions to the regulatory inventory narrowed but did not close the gap between modeled and satellite-observed NO2 over rural regions. Satellite-based top-down emission inventories are created with the regional Comprehensive Air Quality Model with extensions (CAMx) using two techniques: the direct scaling method and discrete Kalman filter (DKF) with decoupled direct method (DDM) sensitivity analysis. The simulations with satellite-inverted inventories are compared to the modeling results using the a priori inventory as well as an inventory created by a ground-level NO2-based DKF inversion. The DKF inversions yield conflicting results: the satellite-based inversion scales up the a priori NOx emissions in most regions by factors of 1.02 to 1.84, leading to 3-55% increase in modeled NO2 column densities and 1-7 ppb increase in ground 8 h ozone concentrations, while the ground-based inversion indicates the a priori NOx emissions should be scaled by factors of 0.34 to 0.57 in each region. However, none of the inversions improve the model performance in simulating aircraft-observed NO2 or ground-level ozone (O3) concentrations.

Inverse modeling of Texas NOx emissions using space-based and ground-based NO2 observations

NASA Astrophysics Data System (ADS)

Tang, W.; Cohan, D.; Lamsal, L. N.; Xiao, X.; Zhou, W.

2013-07-01

Inverse modeling of nitrogen oxide (NOx) emissions using satellite-based NO2 observations has become more prevalent in recent years, but has rarely been applied to regulatory modeling at regional scales. In this study, OMI satellite observations of NO2 column densities are used to conduct inverse modeling of NOx emission inventories for two Texas State Implementation Plan (SIP) modeling episodes. Addition of lightning, aircraft, and soil NOx emissions to the regulatory inventory narrowed but did not close the gap between modeled and satellite observed NO2 over rural regions. Satellite-based top-down emission inventories are created with the regional Comprehensive Air Quality Model with extensions (CAMx) using two techniques: the direct scaling method and discrete Kalman filter (DKF) with Decoupled Direct Method (DDM) sensitivity analysis. The simulations with satellite-inverted inventories are compared to the modeling results using the a priori inventory as well as an inventory created by a ground-level NO2 based DKF inversion. The DKF inversions yield conflicting results: the satellite-based inversion scales up the a priori NOx emissions in most regions by factors of 1.02 to 1.84, leading to 3-55% increase in modeled NO2 column densities and 1-7 ppb increase in ground 8 h ozone concentrations, while the ground-based inversion indicates the a priori NOx emissions should be scaled by factors of 0.34 to 0.57 in each region. However, none of the inversions improve the model performance in simulating aircraft-observed NO2 or ground-level ozone (O3) concentrations.

Antioxidant (A-tocopherol acetate) effect on oxidation stability and NOx emission reduction in methyl ester of Annona oil operated diesel engine

NASA Astrophysics Data System (ADS)

Senthil, R.; Silambarasan, R.; Pranesh, G.

2017-05-01

There is a major drawback while using biodiesel as a alternate fuel for compression ignition diesel engine due to lower heating value, higher viscosity, higher density and higher oxides of nitrogen emission. To minimize these drawbacks, fuel additives can contribute towards engine performance and exhaust emission reduction either directly or indirectly. In this current work, the test was conducted to investigate the effect of antioxidant additive (A-tocopherol acetate) on oxidation stability and NOx emission in a of Annona methyl ester oil (MEAO) fueled diesel engine. The A-tocopherol acetate is mixed in different concentrations such as 0.01, 0.02, 0.03 and 0.04% with 100% by vol MEAO. It is concluded that the antioxidant additive very effective in increasing the oxidation stability and in controlling the NOx emission. Further, the addition of antioxidant additive is slight increase the HC, CO and smoke emissions. Hence, A-tocopherol acetate is very effective in controlling the NOx emission with MEAO operated diesel engine without any major modification.

Reconciling NOx emissions reductions and ozone trends in ...

EPA Pesticide Factsheets

Dynamic evaluation seeks to assess the ability of photochemical models to replicate changes in air quality as emissions and other conditions change. When a model fails to replicate an observed change, a key challenge is to discern whether the discrepancy is caused by errors in meteorological simulations, errors in emission magnitudes and changes, or inaccurate responses of simulated pollutant concentrations to emission changes. In this study, the Community Multiscale Air Quality (CMAQ) model is applied to simulate the ozone (O3) change after the NOx SIP Call and mobile emission controls substantially reduced nitrogen oxides (NOx) emissions in the eastern U.S. from 2002 to 2006. For both modeled and observed O3, changes in episode average daily maximal 8-h O3 were highly correlated (R2 = 0.89) with changes in the 95th percentile, although the magnitudes of reductions increased nonlinearly at high percentile O3 concentrations. Observed downward changes in mean NOx (−11.6 to −2.5 ppb) and 8-h O3 (−10.4 to −4.7 ppb) concentrations in metropolitan areas in the NOx SIP Call region were under-predicted by 31%–64% and 26%–66%, respectively. The under-predicted O3 improvements in the NOx SIP Call region could not be explained by adjusting for temperature biases in the meteorological input, or by considering uncertainties in the chemical reaction rate constants. However, the under-prediction in O3 improvements could be alleviated by 5%–31% by constraining NO

A Fuel-Based Assessment of On-Road and Off-Road Mobile Source Emission Trends

NASA Astrophysics Data System (ADS)

Dallmann, T. R.; Harley, R. A.

2009-12-01

Mobile sources contribute significantly to emissions of nitrogen oxides (NOx) and fine particulate matter (PM2.5) in the United States. These emissions lead to a variety of environmental concerns including adverse human health effects and climate change. In the electric power sector, sulfur dioxide (SO2) and NOx emissions from power plants are measured directly using continuous emission monitoring systems. In contrast for mobile sources, statistical models are used to estimate average emissions from a very large and diverse population of engines. Despite much effort aimed at improving them, mobile source emission inventories continue to have large associated uncertainties. Alternate methods are needed to help evaluate estimates of mobile source emissions and quantify and reduce the associated uncertainties. In this study, a fuel-based approach is used to estimate emissions from mobile sources, including on-road and off-road gasoline and diesel engines. In this approach, engine activity is measured by fuel consumed (in contrast EPA mobile source emission models are based on vehicle km of travel and total amount of engine work output for on-road and off-road engines, respectively). Fuel consumption is defined in this study based on highway fuel tax reports for on-road engines, and from surveys of fuel wholesalers who sell tax-exempt diesel fuel for use in various off-road sectors such as agriculture, construction, and mining. Over the decade-long time period (1996-2006) that is the focus of the present study, national sales of taxable gasoline and diesel fuel intended for on-road use increased by 15 and 43%, respectively. Diesel fuel use by off-road equipment increased by about 20% over the same time period. Growth in fuel consumption offset some of the reductions in pollutant emission factors that occurred during this period. This study relies on in-use measurements of mobile source emission factors, for example from roadside and tunnel studies, remote sensing, and plume capture experiments. Extensive in-use emissions data are available for NOx, especially for on-road engines. Measurements of exhaust PM2.5 emission factors are sparse in comparison. For NOx, there have been dramatic (factor of 2) decreases in emission factors for on-road gasoline engines between 1996 and 2006, due to use of improved catalytic converters on most engines. In contrast, diesel NOx emission factors decreased more gradually over the same time period. Exhaust PM2.5 emission factors appear to have decreased for most engine categories, but emission uncertainties are large for this pollutant. Pollutant emissions were estimated by combining fuel sales with emission factors expressed per unit of fuel burned. Diesel engines are the dominant mobile source of both NOx and PM2.5; the diesel contribution to NOx has increased over time as gasoline engine emissions have declined. Comparing fuel-based emission estimates with EPA’s national emission inventory led to the following conclusions: (1) total emissions of both NOx and PM2.5 estimated by two different methods were similar, (2) the distribution of source contributions to these totals differ significantly, with higher relative contributions coming from on-road diesel engines in this study compared to EPA.

Climate Strategy Impact on Nitrogen Deposition in the USA ...

EPA Pesticide Factsheets

Nitrogen (N) leakage to the environment in the United States costs an estimated $210 billion per year, equivalent to 1-3% of the national GDP, in part due to atmospheric N pollution. Excess N deteriorates ecosystems via eutrophication in water bodies, causing fish kills and additional expense in water treatment (Sobota et al., 2015). To describe the nutrient threshold an ecosystem is able to withstand before its functionality is impaired, the Department of Agriculture developed critical loadings for ecoregions and vegetation types across the U.S. (Pardo et al., 2015). In present conditions, N deposition alone may cause sensitive ecosystems across the United States to exceed these values (Lee et al., 2015). Although the primary contributor to N deposition in the past has been in oxidized forms, or NOx, ammonia (NH3) is expected to be the predominant form in the future as air quality regulations reduce NOx emissions (Ellis et al., 2013). Climate change mitigation measures complicate N projections because many are expected to provide air quality co-benefits through NOx reductions. However, strategies that substitute biofuels for conventional petroleum could lead to an increase in NH3 emissions from fertilizer application. In evaluating climate mitigation strategies, it is imperative that we understand their effects on the N cycle to avoid economic, public health and ecological consequences. In this extended abstract, the author demonstrates how the emission outp

40 CFR 75.5 - Prohibitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

.... (c) No owner or operator of an affected unit shall use any alternative monitoring system, alternative... be discharged, emissions of SO2, NOX or CO2 to the atmosphere without accounting for all such... approved emission monitoring method, and thereby avoid monitoring and recording SO2, NOX, or CO2 emissions...

EPA and California Air Resources Board Approve Remedy to Reduce Excess NOx Emissions from Automatic Transmission “Generation 2” 2.0-Liter Diesel Vehicles

EPA Pesticide Factsheets

On May 17, 2017, EPA and the California Air Resources Board (CARB) approved an emissions modification proposed by Volkswagen that will reduce NOx emissions from automatic transmission diesel Passats for model years 2012-2014.

Assessment of discrepancies between bottom-up and regional emission inventories in Norwegian urban areas

NASA Astrophysics Data System (ADS)

López-Aparicio, Susana; Guevara, Marc; Thunis, Philippe; Cuvelier, Kees; Tarrasón, Leonor

2017-04-01

This study shows the capabilities of a benchmarking system to identify inconsistencies in emission inventories, and to evaluate the reason behind discrepancies as a mean to improve both bottom-up and downscaled emission inventories. Fine scale bottom-up emission inventories for seven urban areas in Norway are compared with three regional emission inventories, EC4MACS, TNO_MACC-II and TNO_MACC-III, downscaled to the same areas. The comparison shows discrepancies in nitrogen oxides (NOx) and particulate matter (PM2.5 and PM10) when evaluating both total and sectorial emissions. The three regional emission inventories underestimate NOx and PM10 traffic emissions by approximately 20-80% and 50-90%, respectively. The main reasons for the underestimation of PM10 emissions from traffic in the regional inventories are related to non-exhaust emissions due to resuspension, which are included in the bottom-up emission inventories but are missing in the official national emissions, and therefore in the downscaled regional inventories. The benchmarking indicates that the most probable reason behind the underestimation of NOx traffic emissions by the regional inventories is the activity data. The fine scale NOx traffic emissions from bottom-up inventories are based on the actual traffic volume at the road link and are much higher than the NOx emissions downscaled from national estimates based on fuel sales and based on population for the urban areas. We have identified important discrepancies in PM2.5 emissions from wood burning for residential heating among all the inventories. These discrepancies are associated with the assumptions made for the allocation of emissions. In the EC4MACs inventory, such assumptions imply high underestimation of PM2.5 emissions from the residential combustion sector in urban areas, which ranges from 40 to 90% compared with the bottom-up inventories. The study shows that in three of the seven Norwegian cities there is need for further improvement of the emission inventories.

The effect of functional forms of nitrogen on fuel-NOx emissions.

PubMed

Zhang, Linghui; Su, Dagen; Zhong, Mingfeng

2015-01-01

This work explores the effects of different nitrogen functional forms on fuel-NOx emissions at 900 °C. The majority of tests are performed with an excess air coefficient of 1.4. Fuel-NOx is detected by measuring N-(1-naphthyl) ethylenediamine dihydrochloride (C₁₂H₁₆Cl₂N₂) via spectrophotometry. The different functional forms of nitrogen in the raw materials are identified by using X-ray photoelectron spectroscopy (XPS). A reliable density functional theory (DFT) method at the B3LYP/6-311++G** level is employed to investigate the reaction pathways of all functional forms of nitrogen during combustion. The results indicate that the functional forms of nitrogen influence the formation of nitrogen oxides. While under the same experimental conditions, fuel-NOx emissions increase by using less activation energy and nitrogen-containing groups with poor thermal stability. It is determined that fuel-NOx emissions vary in the following order: glycine > pyrrole > pyridine > methylenedi-p-phenylene diisocyanate (MDI). Glycine is the chain structure of amino acids in waste-leather and has low activation energy and poor thermal stability. With these properties, it is noted that glycine produces the most fuel-NOx in all of the raw materials studied. More pyrrole than pyridine in coal lead to high yields of fuel-NOx. The lowest yields of fuel-NO x are obtained using polyurethanes in waste-PU.

Particulate and gaseous emissions from different wood fuels during combustion in a small-scale biomass heating system

NASA Astrophysics Data System (ADS)

Olave, R. J.; Forbes, E. G. A.; Johnston, C. R.; Relf, J.

2017-05-01

Woodchip is widely used as fuel in dedicated biomass and, even in some conventional energy generation plants. However, there are concerns about atmospheric air pollution from flue gases emitted during wood biomass combustion, particularly oxides of nitrogen (NOx) and particulates <10 μm diameter (PM10). In the United Kingdom (UK) a small scale biomass heat generation support scheme, the Renewable Heat Incentive (RHI), has been introduced. Qualifying criteria for this scheme have included limits for flue gas emissions of NOX and PM10 of 150 and 30 g per gigajoule (g/GJ) of energy input, respectively. In an experiment, three locally available types of Willow (Salix spp) and one of Sitka spruce (Picea sitchensis) woodchips, showed significant differences in physical and chemical constituents, gaseous and particulate emissions. During combustion in a 120 kW biomass system, air flows, flue gas temperatures and energy output correlated with gaseous emissions, NOx with raw fuel ash, nitrogen, phosphorus and potassium content, as did all flue gas particulate fractions. PM10 ranged from 30.3 to 105.7 g/GJ and NOx from 91.2 to 174.3 g/GJ. Sitka spruce produced significantly lower emissions of PM10 and NOx (27.5 and 52.6% less, respectively) than the three willow fuels, from which emissions were above the RHI emissions limits.

Estimating NOx emissions and surface concentrations at high spatial resolution using OMI

NASA Astrophysics Data System (ADS)

Goldberg, D. L.; Lamsal, L. N.; Loughner, C.; Swartz, W. H.; Saide, P. E.; Carmichael, G. R.; Henze, D. K.; Lu, Z.; Streets, D. G.

2017-12-01

In many instances, NOx emissions are not measured at the source. In these cases, remote sensing techniques are extremely useful in quantifying NOx emissions. Using an exponential modified Gaussian (EMG) fitting of oversampled Ozone Monitoring Instrument (OMI) NO2 data, we estimate NOx emissions and lifetimes in regions where these emissions are uncertain. This work also presents a new high-resolution OMI NO2 dataset derived from the NASA retrieval that can be used to estimate surface level concentrations in the eastern United States and South Korea. To better estimate vertical profile shape factors, we use high-resolution model simulations (Community Multi-scale Air Quality (CMAQ) and WRF-Chem) constrained by in situ aircraft observations to re-calculate tropospheric air mass factors and tropospheric NO2 vertical columns during summertime. The correlation between our satellite product and ground NO2 monitors in urban areas has improved dramatically: r2 = 0.60 in new product, r2 = 0.39 in operational product, signifying that this new product is a better indicator of surface concentrations than the operational product. Our work emphasizes the need to use both high-resolution and high-fidelity models in order to re-calculate vertical column data in areas with large spatial heterogeneities in NOx emissions. The methodologies developed in this work can be applied to other world regions and other satellite data sets to produce high-quality region-specific emissions estimates.

40 CFR 94.305 - Credit generation and use calculation.

Code of Federal Regulations, 2013 CFR

2013-07-01

... engine family, calculate THC+NOX and PM emission credits (positive or negative) according to the equation... applicable cycle-weighted marine engine THC+NOX or PM emission standard in grams per kilowatt-hour. (ii) FEL...

40 CFR 94.305 - Credit generation and use calculation.

Code of Federal Regulations, 2011 CFR

2011-07-01

... engine family, calculate THC+NOX and PM emission credits (positive or negative) according to the equation... applicable cycle-weighted marine engine THC+NOX or PM emission standard in grams per kilowatt-hour. (ii) FEL...

40 CFR 94.305 - Credit generation and use calculation.

Code of Federal Regulations, 2012 CFR

2012-07-01

... engine family, calculate THC+NOX and PM emission credits (positive or negative) according to the equation... applicable cycle-weighted marine engine THC+NOX or PM emission standard in grams per kilowatt-hour. (ii) FEL...

40 CFR 94.305 - Credit generation and use calculation.

Code of Federal Regulations, 2014 CFR

2014-07-01

... engine family, calculate THC+NOX and PM emission credits (positive or negative) according to the equation... applicable cycle-weighted marine engine THC+NOX or PM emission standard in grams per kilowatt-hour. (ii) FEL...

40 CFR 94.305 - Credit generation and use calculation.

Code of Federal Regulations, 2010 CFR

2010-07-01

... engine family, calculate THC+NOX and PM emission credits (positive or negative) according to the equation... applicable cycle-weighted marine engine THC+NOX or PM emission standard in grams per kilowatt-hour. (ii) FEL...

Public Health Impacts of Excess NOX Emissions from Volkswagen Diesel Passenger Vehicles: a comparison between Germany and the United States

NASA Astrophysics Data System (ADS)

Chossiere, G.; Barrett, S. R. H.; Malina, R.; Dedoussi, I. C.; Eastham, S. D.; Ashok, A.

2016-12-01

In September 2015, the Volkswagen Group admitted the use of an illegal emissions control system that activates during vehicle testing for regulatory purposes. Globally, 11 million diesel cars sold between 2008 and 2015 are affected, including about 2.6 million in Germany and 480,000 in the United States. On-road tests suggest that NOx emissions for these cars amount to 0.85 g/km on average, over four times the applicable European limit of 0.18 g/km and more than 20 times the corresponding EPA standard. This study quantifies and compares the human health impacts and costs associated with excess emissions from VW cars driven in Germany and in the United States. A distribution of emissions factors built from existing on-road measurements is combined with sales data and a vehicle fleet model to estimate total excess NOx emissions in each country. In Europe, we used the GEOS-Chem chemistry-transport model to predict the increase in population exposure to fine particulate matter and ozone due to the excess NOx emissions in Germany. The corresponding quantities in the US case were obtained using an adjoint-based air pollution model derived from the GEOS-Chem model. A set of concentration-response functions allowed us to estimate mortality outcomes in terms of early deaths in the US and in Europe. Integrated over the sales period (2008 - 2015), we estimate median mortality impacts from VW excess emissions in Germany to be 1,100 (95% CI: 0 to 3,000) early deaths in Europe, corresponding to 3.9 billion EUR (95% CI: 0 to 10 billion) in associated costs. Another 59 (95% CI: 10 to 150) early deaths is expected in the US as a result of excess emissions released in the country, corresponding to 450 million USD in social costs. We find that excess NOx emissions in Europe have 5 times greater health impacts per kilogram than those in the US due to the higher population density and more NOx-sensitive background conditions in Europe. The gas ratios in the two regions support this finding and highlight the greater availability of free ammonia in Europe than in the US, resulting in more NOx being converted into ammonium nitrate aerosol, and greater concentrations of PM2.5. Conversely, increased NOx emissions result in a decrease in ozone concentrations over Europe, whereas increase in ozone concentration is a driver of early deaths in the US.

A space-based, high-resolution view of notable changes in urban NOx pollution around the world (2005-2014)

NASA Astrophysics Data System (ADS)

Duncan, Bryan N.; Lamsal, Lok N.; Thompson, Anne M.; Yoshida, Yasuko; Lu, Zifeng; Streets, David G.; Hurwitz, Margaret M.; Pickering, Kenneth E.

2016-01-01

Nitrogen oxides (NOx = NO + NO2) are produced during combustion processes and, thus may serve as a proxy for fossil fuel-based energy usage and coemitted greenhouse gases and other pollutants. We use high-resolution nitrogen dioxide (NO2) data from the Ozone Monitoring Instrument (OMI) to analyze changes in urban NO2 levels around the world from 2005 to 2014, finding complex heterogeneity in the changes. We discuss several potential factors that seem to determine these NOx changes. First, environmental regulations resulted in large decreases. The only large increases in the United States may be associated with three areas of intensive energy activity. Second, elevated NO2 levels were observed over many Asian, tropical, and subtropical cities that experienced rapid economic growth. Two of the largest increases occurred over recently expanded petrochemical complexes in Jamnagar (India) and Daesan (Korea). Third, pollution transport from China possibly influenced the Republic of Korea and Japan, diminishing the impact of local pollution controls. However, in China, there were large decreases over Beijing, Shanghai, and the Pearl River Delta, which were likely associated with local emission control efforts. Fourth, civil unrest and its effect on energy usage may have resulted in lower NO2 levels in Libya, Iraq, and Syria. Fifth, spatial heterogeneity within several megacities may reflect mixed efforts to cope with air quality degradation. We also show the potential of high-resolution data for identifying NOx emission sources in regions with a complex mix of sources. Intensive monitoring of the world's tropical/subtropical megacities will remain a priority, as their populations and emissions of pollutants and greenhouse gases are expected to increase significantly.

A Space-based, High-resolution View of Notable Changes in Urban Nox Pollution Around the World (2005 - 2014)

NASA Technical Reports Server (NTRS)

Duncan, Bryan N.; Lamsal, Lok N.; Thompson, Anne M.; Yoshida, Yasuko; Lu, Zifeng; Streets, David G.; Hurwitz, Margaret M.; Pickering, Kenneth E.

2016-01-01

Nitrogen oxides (NOxNO+NO2) are produced during combustion processes and, thus may serve as a proxy for fossil fuel-based energy usage and committed greenhouse gases and other pollutants. We use high-resolution nitrogen dioxide (NO2) data from the Ozone Monitoring Instrument (OMI) to analyze changes in urban NO2 levels around the world from 2005 to 2014, finding complex heterogeneity in the changes. We discuss several potential factors that seem to determine these NOx changes. First, environmental regulations resulted in large decreases. The only large increases in the United States may be associated with three areas of intensive energy activity. Second, elevated NO2 levels were observed over many Asian, tropical, and subtropical cities that experienced rapid economic growth. Two of the largest increases occurred over recently expanded petrochemical complexes in Jamnagar (India) and Daesan (Korea). Third, pollution transport from China possibly influenced the Republic of Korea and Japan, diminishing the impact of local pollution controls. However, in China, there were large decreases over Beijing, Shanghai, and the Pearl River Delta, which were likely associated with local emission control efforts. Fourth, civil unrest and its effect on energy usage may have resulted in lower NO2 levels in Libya, Iraq, and Syria. Fifth, spatial heterogeneity within several megacities may reflect mixed efforts to cope with air quality degradation. We also show the potential of high-resolution data for identifying NOx emission sources in regions with a complex mix of sources. Intensive monitoring of the world's tropical subtropical megacities will remain a priority, as their populations and emissions of pollutants and greenhouse gases are expected to increase significantly.

Tropospheric ozone using an emission tagging technique in the CAM-Chem and WRF-Chem models

NASA Astrophysics Data System (ADS)

Lupascu, A.; Coates, J.; Zhu, S.; Butler, T. M.

2017-12-01

Tropospheric ozone is a short-lived climate forcing pollutant. High concentration of ozone can affect human health (cardiorespiratory and increased mortality due to long-term exposure), and also it damages crops. Attributing ozone concentrations to the contributions from different sources would indicate the effects of locally emitted or transported precursors on ozone levels in specific regions. This information could be used as an important component of the design of emissions reduction strategies by indicating which emission sources could be targeted for effective reductions, thus reducing the burden of ozone pollution. Using a "tagging" approach within the CAM-Chem (global) and WRF-Chem (regional) models, we can quantify the contribution of individual emission of NOx and VOC precursors on air quality. Hence, when precursor emissions of NOx are tagged, we have seen that the largest contributors on ozone levels are the anthropogenic sources, while in the case of precursor emissions of VOCs, the biogenic sources and methane account for more than 50% of ozone levels. Further, we have extended the NOx tagging method in order to investigate continental source region contributions to concentrations of ozone over various receptor regions over the globe, with a zoom over Europe. In general, summertime maximum ozone in most receptor regions is largely attributable to local emissions of anthropogenic NOx and biogenic VOC. During the rest of the year, especially during springtime, ozone in most receptor regions shows stronger influences from anthropogenic emissions of NOx and VOC in remote source regions.

Characterization of NOx, SO2, ethene, and propene from industrial emission sources in Houston, Texas

NASA Astrophysics Data System (ADS)

Washenfelder, R. A.; Trainer, M.; Frost, G. J.; Ryerson, T. B.; Atlas, E. L.; de Gouw, J. A.; Flocke, F. M.; Fried, A.; Holloway, J. S.; Parrish, D. D.; Peischl, J.; Richter, D.; Schauffler, S. M.; Walega, J. G.; Warneke, C.; Weibring, P.; Zheng, W.

2010-08-01

The Houston-Galveston-Brazoria urban area contains industrial petrochemical sources that emit volatile organic compounds and nitrogen oxides, resulting in rapid and efficient ozone production downwind. During September to October 2006, the NOAA WP-3D aircraft conducted research flights as part of the second Texas Air Quality Study (TexAQS II). We use measurements of NOx, SO2, and speciated hydrocarbons from industrial sources in Houston to derive source emission ratios and compare these to emission inventories and the first Texas Air Quality Study (TexAQS) in 2000. Between 2000 and 2006, NOx/CO2 emission ratios changed by an average of -29% ± 20%, while a significant trend in SO2/CO2 emission ratios was not observed. We find that high hydrocarbon emissions are routine for the isolated petrochemical facilities. Ethene (C2H4) and propene (C3H6) are the major contributors to ozone formation based on calculations of OH reactivity for organic species including C2-C10 alkanes, C2-C5 alkenes, ethyne, and C2-C5 aldehydes and ketones. Measured ratios of C2H4/NOx and C3H6/NOx exceed emission inventory values by factors of 1.4-20 and 1-24, respectively. We examine trends in C2H4/NOx and C3H6/NOx ratios between 2000 and 2006 for the isolated petrochemical sources and estimate a change of -30% ± 30%, with significant day-to-day and within-plume variability. Median ambient mixing ratios of ethene and propene in Houston show decreases of -52% and -48%, respectively, between 2000 and 2006. The formaldehyde, acetaldehyde, and peroxyacetyl nitrate products produced by alkene oxidation are observed downwind, and their time evolution is consistent with the rapid photochemistry that also produces ozone.

Emissions of NOx, particle mass and particle numbers from aircraft main engines, APU's and handling equipment at Copenhagen Airport

NASA Astrophysics Data System (ADS)

Winther, Morten; Kousgaard, Uffe; Ellermann, Thomas; Massling, Andreas; Nøjgaard, Jacob Klenø; Ketzel, Matthias

2015-01-01

This paper presents a detailed emission inventory for NOx, particle mass (PM) and particle numbers (PN) for aircraft main engines, APU's and handling equipment at Copenhagen Airport (CPH) based on time specific activity data and representative emission factors for the airport. The inventory has a high spatial resolution of 5 m × 5 m in order to be suited for further air quality dispersion calculations. Results are shown for the entire airport and for a section of the airport apron area ("inner apron") in focus. The methodology presented in this paper can be used to quantify the emissions from aircraft main engines, APU and handling equipment in other airports. For the entire airport, aircraft main engines is the largest source of fuel consumption (93%), NOx, (87%), PM (61%) and PN (95%). The calculated fuel consumption [NOx, PM, PN] shares for APU's and handling equipment are 5% [4%, 8%, 5%] and 2% [9%, 31%, 0%], respectively. At the inner apron area for handling equipment the share of fuel consumption [NOx, PM, PN] are 24% [63%, 75%, 2%], whereas APU and main engines shares are 43% [25%, 19%, 54%], and 33% [11%, 6%, 43%], respectively. The inner apron NOx and PM emission levels are high for handling equipment due to high emission factors for the diesel fuelled handling equipment and small for aircraft main engines due to small idle-power emission factors. Handling equipment is however a small PN source due to the low number based emission factors. Jet fuel sulphur-PM sensitivity calculations made in this study with the ICAO FOA3.0 method suggest that more than half of the PM emissions from aircraft main engines at CPH originate from the sulphur content of the fuel used at the airport. Aircraft main engine PN emissions are very sensitive to the underlying assumptions. Replacing this study's literature based average emission factors with "high" and "low" emission factors from the literature, the aircraft main engine PN emissions were estimated to change with a factor of 14.

An experimental study on effect of coke ratio on SO2 and NOx emissions in sintering process

NASA Astrophysics Data System (ADS)

Wang, Hui; Zhang, Pu; Yang, Jingling

2018-02-01

By using the sinter cup experiment, the effects of different coke ratios of 0%, 25%, 50%, 75%, and 100% on the formation and total emissions of SO2 and NOx in the sintering process were studied with the Testo350 flue gas analyzer. The experimental results show that the emissions of SO2 and NOx are closely related to sintering process. With the increase of the coke proportion, the sintering temperature changes and the maximum peak time appears earlier. SO2 concentration has a bimodal distribution and NOx concentration has a triple peak. Besides, the both maximum peaks appear at the end of sintering. In addition, due to the increasing of the S and N contents in the fuel with the coke ratios from 0% to 100%, the amounts of SO2 and NOx emissions are raised respectively at 10.82 mg, 11.42 mg, 13.84 mg, 13.69 mg, 20.36 mg and 3.11 mg, 3.39 mg, 4.44 mg, 4.31 mg, 6.16 mg.

Effects of temperature-dependent NOx emissions on continental ozone production

NASA Astrophysics Data System (ADS)

Romer, Paul S.; Duffey, Kaitlin C.; Wooldridge, Paul J.; Edgerton, Eric; Baumann, Karsten; Feiner, Philip A.; Miller, David O.; Brune, William H.; Koss, Abigail R.; de Gouw, Joost A.; Misztal, Pawel K.; Goldstein, Allen H.; Cohen, Ronald C.

2018-02-01

Surface ozone concentrations are observed to increase with rising temperatures, but the mechanisms responsible for this effect in rural and remote continental regions remain uncertain. Better understanding of the effects of temperature on ozone is crucial to understanding global air quality and how it may be affected by climate change. We combine measurements from a focused ground campaign in summer 2013 with a long-term record from a forested site in the rural southeastern United States, to examine how daily average temperature affects ozone production. We find that changes to local chemistry are key drivers of increased ozone concentrations on hotter days, with integrated daily ozone production increasing by 2.3 ppb °C-1. Nearly half of this increase is attributable to temperature-driven increases in emissions of nitrogen oxides (NOx), most likely by soil microbes. The increase of soil NOx emissions with temperature suggests that ozone will continue to increase with temperature in the future, even as direct anthropogenic NOx emissions decrease dramatically. The links between temperature, soil NOx, and ozone form a positive climate feedback.

40 CFR 60.4174 - Recordkeeping and reporting.

Code of Federal Regulations, 2011 CFR

2011-07-01

... unit is subject to an Acid Rain emission limitation or the CAIR NOX Annual Trading Program, CAIR SO2... are also subject to an Acid Rain emissions limitation or the CAIR NOX Annual Trading Program, CAIR SO2...

40 CFR 60.4174 - Recordkeeping and reporting.

Code of Federal Regulations, 2010 CFR

2010-07-01

... unit is subject to an Acid Rain emission limitation or the CAIR NOX Annual Trading Program, CAIR SO2... are also subject to an Acid Rain emissions limitation or the CAIR NOX Annual Trading Program, CAIR SO2...

Environmental assessment of a crude-oil heater using staged air lances for NOx reduction. Volume 1. Technical results. Final report June 1981-November 1983

DOE Office of Scientific and Technical Information (OSTI.GOV)

DeRosier, R.

1984-07-01

This volume of the report gives emission results from field tests of a crude-oil process heater burning a combination of oil and refinery gas. The heater had been modified by adding a system for injecting secondary air to reduce NOx emissions. One test was conducted with the staged air system (low NOx), and the other, without (baseline). Tests included continuous monitoring of flue gas emissions and source assessment sampling system (SASS) sampling of the flue gas with subsequent laboratory analysis of the samples utilizing gas chromatography (GC), infrared spectrometry (IR), gas chromatography/mass spectroscopy (GC/MS), and low resolution mass spectrometry (SSMS)more » for trace metals. LRMS analysis suggested the presence of eight compound categories in the organic emissions during the baseline test and four in the low-NOx test.« less

Vehicle Real Driving Emissions of Nitrogen Oxides in an Urban Area from a large Vehicle Fleet

NASA Astrophysics Data System (ADS)

Pöhler, Denis; Horbanski, Martin; Oesterle, Tobias; Adler, Tim; Reh, Miriam; Tirpitz, Lukas; Kanatschnig, Florian; Lampel, Joahnnes; Platt, Ulrich

2016-04-01

Nitrogen Oxide (NOx=NO +NO2) emissions by road vehicles are the major contributor for poor air quality in urban areas. High NOx concentrations, and especially NO2, are typically the most problematic pollution in cities. However, emissions vary significantly depending on the type of vehicle, its engine, the age, condition of the vehicle, driving properties, modifications and many more. Even if official NOx emission data of the manufacturer exist, they are only valid for new vehicles and the current vehicle emission scandal shows clearly that these data are often wrong. Thus, real driving emissions (RDE) of the current vehicle fleet is required. With such data the contribution of individual vehicles to the NO2 and NOx levels in urban areas can be estimated. Significant reduction of NOx concentrations can be achieved by identifying the strong emitting vehicles and excluding, replace or modify them. We developed a precise and fast ICAD (Iterative CAvity DOAS) NO2 instrument which can measure the concentration within the emission plume of vehicles under real driving conditions. The sampling was performed with an inlet at the front of a car which was following the investigated vehicles. The instrument measure NO2 and additionally CO2 with a time resolution of 2 seconds. With the observed NO2 values already strong emitters can easily be identified. With the use of known CO2 emissions, more reliable emissions for NO2 can be calculated for each vehicle. Currently the system is expanded with a NOx channel to derive the total nitrogen oxide emissions. The system was successfully applied in several studies over the last two years to investigate NO2 RDE. More than thousand vehicles were investigated. We observed that several vehicles from various brands show much higher emissions than allowed (more than a factor of 5). Highest emissions correlate for trucks and busses typically to older vehicles, what is not the case for cars. A large variability between different cars was found which could often make up a factor of 10 or more. Often new Diesel cars are one of the strongest emitters, which agree well with other findings. However, older busses and trucks feature regularly the highest emissions, but also here strong variability between different vehicle types with different exhaust treatment and modification is observed. This is especially a problem with busses from the public transport which significantly contribute to urban air pollution. Identifying first the strongest emitting busses, which should be replaced first, can help to faster improve urban air quality. New busses and trucks, beside from few exceptions, show surprisingly relatively low emissions. The exceptions indicate potentially broken NOx exhaust treatment. All these findings show that regular RDE are necessary for the whole vehicle fleet to identify strongest NOx emitters and develop strategies to reduce their emissions. They also allow to provide more accurate model calculations on total emissions in urban areas.

Impact of the Volkswagen emissions control defeat device on US public health

NASA Astrophysics Data System (ADS)

Barrett, Steven R. H.; Speth, Raymond L.; Eastham, Sebastian D.; Dedoussi, Irene C.; Ashok, Akshay; Malina, Robert; Keith, David W.

2015-11-01

The US Environmental Protection Agency (EPA) has alleged that Volkswagen Group of America (VW) violated the Clean Air Act (CAA) by developing and installing emissions control system ‘defeat devices’ (software) in model year 2009-2015 vehicles with 2.0 litre diesel engines. VW has admitted the inclusion of defeat devices. On-road emissions testing suggests that in-use NOx emissions for these vehicles are a factor of 10 to 40 above the EPA standard. In this paper we quantify the human health impacts and associated costs of the excess emissions. We propagate uncertainties throughout the analysis. A distribution function for excess emissions is estimated based on available in-use NOx emissions measurements. We then use vehicle sales data and the STEP vehicle fleet model to estimate vehicle distance traveled per year for the fleet. The excess NOx emissions are allocated on a 50 km grid using an EPA estimate of the light duty diesel vehicle NOx emissions distribution. We apply a GEOS-Chem adjoint-based rapid air pollution exposure model to produce estimates of particulate matter and ozone exposure due to the spatially resolved excess NOx emissions. A set of concentration-response functions is applied to estimate mortality and morbidity outcomes. Integrated over the sales period (2008-2015) we estimate that the excess emissions will cause 59 (95% CI: 10 to 150) early deaths in the US. When monetizing premature mortality using EPA-recommended data, we find a social cost of ˜450m over the sales period. For the current fleet, we estimate that a return to compliance for all affected vehicles by the end of 2016 will avert ˜130 early deaths and avoid ˜840m in social costs compared to a counterfactual case without recall.

Utility experience of Phase I compliance on Chalk Point Unit 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eberhardt, W.H.; Henry, R.J.

1995-03-01

Potomac Electric Power Company`s Chalk Point Generating Station Unit 2 has recently undergone a retrofit to comply with Phase I of the 1990 Clean Air Act Amendments (CAAA) Title IV requirements. The approach taken was to install low NOx burners and overfire air to reduce NOx emissions and switch to lower sulfur coal to comply with Phase I sulfur dioxide (SO{sub 2}) emission limits. This approach was chosen based on a unique combination of sophisticated tools, boiler modeling, experience, testing, and cooperation between the Owners, Engineers, and the equipment Manufacturers. The result was a project performed at a reasonable costmore » and minimum risk to plant reliability and performance while meeting the specified requirements of the regulations. The Unit 2 retrofit will be followed by the retrofit of its identical sister unit, Unit 1, in the late fall of 1994. In addition to the Low NOx system retrofit and coal switching, a new distributed control system (DCS), burner management system (BMS), new ignitors, and the capability to fire natural gas on both main burners and ignitors was added. A four month outage was followed by a series of optimization tests which were designed to reduce the emissions to the compliance limit while minimizing impacts on the boiler operation. After boiler startup, burner and pulverizer performance adjustments were required resulting in dramatic improvement in both boiler and burner performance. This paper describes the approach towards achieving CAAA compliance and the net results: impacts of the Low NOx system and the Phase I coal on the boiler and auxiliary plant equipment and the adjustments which had to be made to eliminate initial operating problems. Results of months of optimization testing are presented as related to emissions, furnace slagging, flame shape, unburned carbon, steam temperatures, and tube metal temperatures.« less

Impact of a nitrogen emission control area (NECA) for ship traffic on the future air quality in the Baltic Sea region

NASA Astrophysics Data System (ADS)

Karl, Matthias; Geyer, Beate; Bieser, Johannes; Matthias, Volker; Quante, Markus; Jalkanen, Jukka-Pekka; Johansson, Lasse; Fridell, Erik

2017-04-01

Deposition of nitrogen compounds originating from shipping activities contribute to eutrophication of the Baltic Sea and coastal areas in the Baltic Sea region. Emissions of nitrogen oxides (NOx) from shipping on the Baltic Sea are comparable to the combined land-based emissions of NOx from Finland and Sweden and have been relatively stable over the last decade. However, expected future growth of maritime transport will result in higher fuel consumption and, if not compensated by increased transport efficiency or other measures, lead to higher total emissions of NOx from shipping. For the Baltic Sea a nitrogen emission control area (NECA) will become effective in 2021 - permitting only new built ships that are compliant with stringent Tier III emission limits - with the target of reducing NOx-emissions. In order to study the effect of implementing a Baltic Sea NECA-2021 on air quality and nitrogen deposition two future scenarios were designed; one with implementation of a NECA for the Baltic Sea starting in 2021 and another with no NECA implemented. The same increase of ship traffic was assumed for both future scenarios. Since complete fleet renewal with low NOx-emitting engines is not expected until 20-30 years after the NECA entry date, year 2040 was chosen as future scenario year. The Community Multiscale Air Quality (CMAQ) model was used to simulate the current and future air quality situation. The nested simulation runs with CMAQ were performed on a horizontal resolution of 4 km × 4 km for the entire Baltic Sea region. The meteorological year 2012 was chosen for the simulation of the current and future air quality situation since the 2m-temperature and precipitation anomalies of 2012 are closely aligned to the 2004-2014 decadal average over Baltic Proper. High-resolution meteorology obtained from COSMO-CLM was used for the regional simulations. Ship emissions were generated with the Ship Traffic Emission Assessment Model (STEAM) by the Finnish Meteorological Institute (FMI) using the Automatic Identification System (AIS) network data to allocate ship positions. Gridded land-based emissions were taken from the SMOKE-EU model which is based on the official EMEP data. Future land-based emissions were reduced in accordance with current legislation. Model simulations for the current situation show that shipping emissions are the main contributor to ambient NO2 concentrations over the Baltic Sea. Shipping emissions are responsible for 40-70 % of the particulate nitrate concentrations during the summer months. Relative contribution of shipping emissions to monthly total nitrogen deposition, as a sum of oxidized and reduced nitrogen compounds, was highest in summer, with up to 60 % in the northern part of the Baltic Proper, while it was on average 10 % for other parts of the Baltic Sea. With the NECA in the Baltic Sea in effect from 2021, the reduction of reactive nitrogen concentrations and deposition in the Baltic Sea region compared to a scenario without Tier III regulations is significant.

40 CFR 86.1709-99 - Exhaust emission standards for 1999 and later light light-duty trucks.

Code of Federal Regulations, 2013 CFR

2013-07-01

... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE...+NOX emission control effectiveness during A/C-on operation when the vehicle is operated under... in control system NMHC+NOX effectiveness do occur as a result of such calibrations, the manufacturer...

40 CFR 86.1708-99 - Exhaust emission standards for 1999 and later light-duty vehicles.

Code of Federal Regulations, 2013 CFR

2013-07-01

... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE HIGHWAY...+NOX emission control effectiveness during A/C-on operation when the vehicle is operated under... in control system NMHC+NOX effectiveness do occur as a result of such calibrations, the manufacturer...

40 CFR 86.1708-99 - Exhaust emission standards for 1999 and later light-duty vehicles.

Code of Federal Regulations, 2012 CFR

2012-07-01

... PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE HIGHWAY...+NOX emission control effectiveness during A/C-on operation when the vehicle is operated under... in control system NMHC+NOX effectiveness do occur as a result of such calibrations, the manufacturer...

40 CFR 86.1709-99 - Exhaust emission standards for 1999 and later light light-duty trucks.

Code of Federal Regulations, 2012 CFR

2012-07-01

... ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE...+NOX emission control effectiveness during A/C-on operation when the vehicle is operated under... in control system NMHC+NOX effectiveness do occur as a result of such calibrations, the manufacturer...

40 CFR 76.14 - Monitoring, recordkeeping, and reporting.

Code of Federal Regulations, 2011 CFR

2011-07-01

... NOX emission control system to the owner or operator showing that such system was designed to meet the... emission control system that were not included in the design specifications and performance guarantee, but... regard to the following types of Group 1, Phase I units: (i) Units employing no new NOX emission control...

40 CFR 76.14 - Monitoring, recordkeeping, and reporting.

Code of Federal Regulations, 2012 CFR

2012-07-01

... NOX emission control system to the owner or operator showing that such system was designed to meet the... emission control system that were not included in the design specifications and performance guarantee, but... regard to the following types of Group 1, Phase I units: (i) Units employing no new NOX emission control...

40 CFR 76.14 - Monitoring, recordkeeping, and reporting.

Code of Federal Regulations, 2010 CFR

2010-07-01

... NOX emission control system to the owner or operator showing that such system was designed to meet the... emission control system that were not included in the design specifications and performance guarantee, but... regard to the following types of Group 1, Phase I units: (i) Units employing no new NOX emission control...

40 CFR 86.127-00 - Test procedures; overview.

Code of Federal Regulations, 2013 CFR

2013-07-01

... following emissions: (1) Gaseous exhaust THC, CO, NOX. CO2 (for petroleum-fueled and gaseous- fueled... vehicles). (b) The FTP Otto-cycle exhaust emission test is designed to determine gaseous THC, CO, CO2, CH4... determine gaseous THC, NMHC, CO, CO2, CH4, and NOX emissions from gasoline-fueled or diesel-fueled vehicles...

40 CFR 86.127-00 - Test procedures; overview.

Code of Federal Regulations, 2014 CFR

2014-07-01

... following emissions: (1) Gaseous exhaust THC, CO, NOX. CO2 (for petroleum-fueled and gaseous- fueled... vehicles). (b) The FTP Otto-cycle exhaust emission test is designed to determine gaseous THC, CO, CO2, CH4... determine gaseous THC, NMHC, CO, CO2, CH4, and NOX emissions from gasoline-fueled or diesel-fueled vehicles...

40 CFR 86.127-00 - Test procedures; overview.

Code of Federal Regulations, 2012 CFR

2012-07-01

... following emissions: (1) Gaseous exhaust THC, CO, NOX. CO2 (for petroleum-fueled and gaseous- fueled... vehicles). (b) The FTP Otto-cycle exhaust emission test is designed to determine gaseous THC, CO, CO2, CH4... determine gaseous THC, NMHC, CO, CO2, CH4, and NOX emissions from gasoline-fueled or diesel-fueled vehicles...

40 CFR 97.254 - Compliance with CAIR SO2 emissions limitation.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Compliance with CAIR SO2 emissions... PROGRAMS (CONTINUED) FEDERAL NOX BUDGET TRADING PROGRAM AND CAIR NOX AND SO2 TRADING PROGRAMS CAIR SO2 Allowance Tracking System § 97.254 Compliance with CAIR SO2 emissions limitation. (a) Allowance transfer...

40 CFR 96.254 - Compliance with CAIR SO2 emissions limitation.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Compliance with CAIR SO2 emissions... PROGRAMS (CONTINUED) NOX BUDGET TRADING PROGRAM AND CAIR NOX AND SO2 TRADING PROGRAMS FOR STATE IMPLEMENTATION PLANS CAIR SO2 Allowance Tracking System § 96.254 Compliance with CAIR SO2 emissions limitation...

40 CFR 96.75 - Petitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... subject to an Acid Rain emissions limitation may submit a petition under § 75.66 of this chapter to the... account representative of a NOX Budget unit that is not subject to an Acid Rain emissions limitation may... account representative of a NOX Budget unit that is subject to an Acid Rain emissions limitation may...

40 CFR 96.75 - Petitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... subject to an Acid Rain emissions limitation may submit a petition under § 75.66 of this chapter to the... account representative of a NOX Budget unit that is not subject to an Acid Rain emissions limitation may... account representative of a NOX Budget unit that is subject to an Acid Rain emissions limitation may...

40 CFR 96.75 - Petitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... subject to an Acid Rain emissions limitation may submit a petition under § 75.66 of this chapter to the... account representative of a NOX Budget unit that is not subject to an Acid Rain emissions limitation may... account representative of a NOX Budget unit that is subject to an Acid Rain emissions limitation may...

40 CFR 96.75 - Petitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... subject to an Acid Rain emissions limitation may submit a petition under § 75.66 of this chapter to the... account representative of a NOX Budget unit that is not subject to an Acid Rain emissions limitation may... account representative of a NOX Budget unit that is subject to an Acid Rain emissions limitation may...

40 CFR 96.75 - Petitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... subject to an Acid Rain emissions limitation may submit a petition under § 75.66 of this chapter to the... account representative of a NOX Budget unit that is not subject to an Acid Rain emissions limitation may... account representative of a NOX Budget unit that is subject to an Acid Rain emissions limitation may...

Nox Emission Reduction in Commercial Jets Through Water Injection

NASA Technical Reports Server (NTRS)

Balepin, Vladimir; Ossello, Chris; Snyder, Chris

2002-01-01

This paper discusses a method of the nitrogen oxides (NOx) emission reduction through the injection of water in commercial turbofan engines during the takeoff and climbout cycles. In addition to emission reduction, this method can significantly reduce turbine temperature during the most demanding operational modes (takeoff and climbout) and increase engine reliability and life.

Exhaust emissions from engines of the Detroit Diesel Corporation in transit buses: a decade of trends.

PubMed

Prucz, J C; Clark, N N; Gautam, M; Lyons, D W

2001-05-01

In the U.S.A., exhaust emissions from city buses fueled by diesel are not characterized well because current emission standards require engine tests rather than tests of whole vehicles. Two transportable chassis dynamometer laboratories developed and operated by West Virginia University (WVU) have been used extensively to gather realistic emission data from heavy-duty vehicles, including buses, tested in simulated driving conditions. A subset of these data has been utilized for a comprehensive introspection into the trends of regulated emissions from transit buses over the last 7 years, which has been prompted by continuously tightening restrictions on one hand, along with remarkable technological progress, on the other hand. Two widely used models of diesel engines manufactured by the Detroit Diesel Corporation (DDC) have been selected as a case-study for such an overview, based on full-scale, on-site testing of actual city buses, driven in accordance with the SAE J1376 standard of a Commercial Business District (CBD) cycle. The results provide solid, quantitative evidence that most regulated emissions from engines produced by DDC have declined over the years, especially with the transition from the 6V-92TA to the Series 50 models. This improvement is remarkable mainly for the emissions of particulate matter (PM), that are lower by over 70%, on average, for the Series 50 engines, though the emissions of nitrogen oxides (NOx) exhibit a reversed trend, showing a degradation of about 6%, on average, with the transition from 6V-92TA to the Series 50 engines. The expected trend of decreasing emission levels with the model year of the engine is clear and consistent for particulate matter (PM), hydrocarbons (HC), carbon monoxide (CO), and nitrogen oxides (NOx), starting with the 1990 models, although it is not conclusive for carbon dioxide (CO2) emissions.

Application of an EGR system in a direct injection diesel engine to reduce NOx emissions

NASA Astrophysics Data System (ADS)

De Serio, D.; De Oliveira, A.; Sodré, J. R.

2016-09-01

This work presents the application of an exhaust gas recirculation (EGR) system in a direct injection diesel engine operating with diesel oil containing 7% biodiesel (B7). EGR rates of up to 10% were applied with the primary aim to reduce oxides of nitrogen (NOx) emissions. The experiments were conducted in a 44 kW diesel power generator to evaluate engine performance and emissions for different load settings. The use of EGR caused a peak pressure reduction during the combustion process and a decrease in thermal efficiency, mainly at high engine loads. A reduction of NOx emissions of up to 26% was achieved, though penalizing carbon monoxide (CO) and total hydrocarbons (THC) emissions.

Intake fraction of PM2.5 and NOX from vehicle emissions in Beijing based on personal exposure data

NASA Astrophysics Data System (ADS)

Du, Xuan; Wu, Ye; Fu, Lixin; Wang, Shuxiao; Zhang, Shaojun; Hao, Jiming

2012-09-01

The intake fraction (iF) is the portion of attributable population intake of a source emissions, and is used to link pollutant emissions and population exposure. This study is the first work that reported individual intake fraction of PM2.5 and NOX from vehicle emissions based on personal exposure data in China. We employed PM2.5 and NOX measurement data from 24-h personal exposure sampling and concentration monitoring in traffic environments in the urban area of Beijing to estimate the individual intake fraction (iFi). iFi distributions are presented in microenvironments (traffic, work, home) for adults and children. The individual results are used to calculate the intake fraction for the children group and the adults group in the urban area of Beijing. The iF of PM2.5 for the whole population of these two groups in Beijing is 153 per million, which is significantly higher than those estimates in the United States (1-50 per million) and Mexico (23-120 per million). The iF of NOX is 70 per million, among which the intake in the traffic micro-environment ranks first compared to the iF in the home and office due to a high accumulation of NOX concentration in vehicles. PM2.5 and NOX intake fraction values from vehicle emissions in this study are from at least several times to one order of magnitude higher than those from other industry sources in China. This strongly suggests the health risk from vehicle emissions is significantly higher. Therefore, to protect human health, especially for the large number of people living in the cities of China, controlling vehicle emissions should be the highest priority.

Transcriptional regulation of NADPH oxidase isoforms, Nox1 and Nox4, by nuclear factor-{kappa}B in human aortic smooth muscle cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Manea, Adrian, E-mail: adrian.manea@icbp.ro; Tanase, Laurentia I.; Raicu, Monica

Inflammation-induced changes in the activity and expression of NADPH oxidases (Nox) play a key role in atherogenesis. The molecular mechanisms of Nox regulation are scantily elucidated. Since nuclear factor-{kappa}B (NF-{kappa}B) controls the expression of many genes associated to inflammation-related diseases, in this study we have investigated the role of NF-{kappa}B signaling in the regulation of Nox1 and Nox4 transcription in human aortic smooth muscle cells (SMCs). Cultured cells were exposed to tumor necrosis factor-{alpha} (TNF{alpha}), a potent inducer of both Nox and NF-{kappa}B, up to 24 h. Lucigenin-enhanced chemiluminescence and dichlorofluorescein assays, real-time polymerase chain reaction, and Western blot analysismore » showed that inhibition of NF-{kappa}B pathway reduced significantly the TNF{alpha}-dependent up-regulation of Nox-derived reactive oxygen species production, Nox1 and Nox4 expression. In silico analysis indicated the existence of typical NF-{kappa}B elements in the promoters of Nox1 and Nox4. Transient overexpression of p65/NF-{kappa}B significantly increased the promoter activities of both isoforms. Physical interaction of p65/NF-{kappa}B proteins with the predicted sites was demonstrated by chromatin immunoprecipitation assay. These findings demonstrate that NF-{kappa}B is an essential regulator of Nox1- and Nox4-containing NADPH oxidase in SMCs. Elucidation of the complex relationships between NF-{kappa}B and Nox enzymes may lead to a novel pharmacological strategy to reduce both inflammation and oxidative stress in atherosclerosis and its associated complications.« less

DI Diesel Performance and Emissions Models

DTIC Science & Technology

2003-06-11

Skeletal mechanism for NOx chemistry in diesel engines ,” SAE Paper 981450, 1998 SAE Transactions, Vol. 107, Sect. 4, J. Fuels and... mechanism for NOx chemistry proposed by Mellor et al. (1998a) is incorporated in an engine simulation code. The two-zone model, also proposed by Mellor et...34Dynamic Application of a Skeletal Mechanism for DI Diesel NOx Emissions," SAE Paper 2001-01-1984, SAE Trans., J. Fuels & Lubricants,

Regional air quality management aspects of climate change: impact of climate mitigation options on regional air emissions.

PubMed

Rudokas, Jason; Miller, Paul J; Trail, Marcus A; Russell, Armistead G

2015-04-21

We investigate the projected impact of six climate mitigation scenarios on U.S. emissions of carbon dioxide (CO2), sulfur dioxide (SO2), and nitrogen oxides (NOX) associated with energy use in major sectors of the U.S. economy (commercial, residential, industrial, electricity generation, and transportation). We use the EPA U.S. 9-region national database with the MARKet Allocation energy system model to project emissions changes over the 2005 to 2050 time frame. The modeled scenarios are two carbon tax, two low carbon transportation, and two biomass fuel choice scenarios. In the lower carbon tax and both biomass fuel choice scenarios, SO2 and NOX achieve reductions largely through pre-existing rules and policies, with only relatively modest additional changes occurring from the climate mitigation measures. The higher carbon tax scenario projects greater declines in CO2 and SO2 relative to the 2050 reference case, but electricity sector NOX increases. This is a result of reduced investments in power plant NOX controls in earlier years in anticipation of accelerated coal power plant retirements, energy penalties associated with carbon capture systems, and shifting of NOX emissions in later years from power plants subject to a regional NOX cap to those in regions not subject to the cap.

A new modeling approach for assessing the contribution of industrial and traffic emissions to ambient NOx concentrations

NASA Astrophysics Data System (ADS)

Chen, Shimon; Yuval; Broday, David M.

2018-01-01

The Optimized Dispersion Model (ODM) is uniquely capable of incorporating emission estimates, ambient air quality monitoring data and meteorology to provide reliable high-resolution (in both time and space) air quality estimates using non-linear regression. However, it was so far not capable of describing the effects of emissions from elevated sources. We formulated an additional term to extend the ODM such that these sources can be accounted for, and implemented it in modeling the fine spatiotemporal patterns of ambient NOx concentrations over the coastal plain of Israel. The diurnal and seasonal variation in the contribution of industry to the ambient NOx is presented, as well as its spatial features. Although industrial stacks are responsible for 88% of the NOx emissions in the study area, their contribution to ambient NOx levels is generally about 2% with a maximal upper bound of 27%. Meteorology has a major role in this source allocation, with the highest impact of industry in the summer months, when the wind is blowing inland past the coastal stacks and vertical mixing is substantial. The new Optimized Dispersion Model (ODM) out-performs both Inverse-Distance-Weighing (IDW) interpolation and a previous ODM version in predicting ambient NOx concentrations. The performance of the new model is thoroughly assessed.

Forty years of improvements in European air quality: regional policy-industry interactions with global impacts

NASA Astrophysics Data System (ADS)

Crippa, Monica; Janssens-Maenhout, Greet; Dentener, Frank; Guizzardi, Diego; Sindelarova, Katerina; Muntean, Marilena; Van Dingenen, Rita; Granier, Claire

2016-03-01

The EDGARv4.3.1 (Emissions Database for Global Atmospheric Research) global anthropogenic emissions inventory of gaseous (SO2, NOx, CO, non-methane volatile organic compounds and NH3) and particulate (PM10, PM2.5, black and organic carbon) air pollutants for the period 1970-2010 is used to develop retrospective air pollution emissions scenarios to quantify the roles and contributions of changes in energy consumption and efficiency, technology progress and end-of-pipe emission reduction measures and their resulting impact on health and crop yields at European and global scale. The reference EDGARv4.3.1 emissions include observed and reported changes in activity data, fuel consumption and air pollution abatement technologies over the past 4 decades, combined with Tier 1 and region-specific Tier 2 emission factors. Two further retrospective scenarios assess the interplay of policy and industry. The highest emission STAG_TECH scenario assesses the impact of the technology and end-of-pipe reduction measures in the European Union, by considering historical fuel consumption, along with a stagnation of technology with constant emission factors since 1970, and assuming no further abatement measures and improvement imposed by European emission standards. The lowest emission STAG_ENERGY scenario evaluates the impact of increased fuel consumption by considering unchanged energy consumption since the year 1970, but assuming the technological development, end-of-pipe reductions, fuel mix and energy efficiency of 2010. Our scenario analysis focuses on the three most important and most regulated sectors (power generation, manufacturing industry and road transport), which are subject to multi-pollutant European Union Air Quality regulations. Stagnation of technology and air pollution reduction measures at 1970 levels would have led to 129 % (or factor 2.3) higher SO2, 71 % higher NOx and 69 % higher PM2.5 emissions in Europe (EU27), demonstrating the large role that technology has played in reducing emissions in 2010. However, stagnation of energy consumption at 1970 levels, but with 2010 fuel mix and energy efficiency, and assuming current (year 2010) technology and emission control standards, would have lowered today's NOx emissions by ca. 38 %, SO2 by 50 % and PM2.5 by 12 % in Europe. A reduced-form chemical transport model is applied to calculate regional and global levels of aerosol and ozone concentrations and to assess the associated impact of air quality improvements on human health and crop yield loss, showing substantial impacts of EU technologies and standards inside as well as outside Europe. We assess that the interplay of policy and technological advance in Europe had substantial benefits in Europe, but also led to an important improvement of particulate matter air quality in other parts of the world.

Decadal changes in summertime reactive oxidized nitrogen and surface ozone over the Southeast United States

NASA Astrophysics Data System (ADS)

Li, Jingyi; Mao, Jingqiu; Fiore, Arlene M.; Cohen, Ronald C.; Crounse, John D.; Teng, Alex P.; Wennberg, Paul O.; Lee, Ben H.; Lopez-Hilfiker, Felipe D.; Thornton, Joel A.; Peischl, Jeff; Pollack, Ilana B.; Ryerson, Thomas B.; Veres, Patrick; Roberts, James M.; Neuman, J. Andrew; Nowak, John B.; Wolfe, Glenn M.; Hanisco, Thomas F.; Fried, Alan; Singh, Hanwant B.; Dibb, Jack; Paulot, Fabien; Horowitz, Larry W.

2018-02-01

Widespread efforts to abate ozone (O3) smog have significantly reduced emissions of nitrogen oxides (NOx) over the past 2 decades in the Southeast US, a place heavily influenced by both anthropogenic and biogenic emissions. How reactive nitrogen speciation responds to the reduction in NOx emissions in this region remains to be elucidated. Here we exploit aircraft measurements from ICARTT (July-August 2004), SENEX (June-July 2013), and SEAC4RS (August-September 2013) and long-term ground measurement networks alongside a global chemistry-climate model to examine decadal changes in summertime reactive oxidized nitrogen (RON) and ozone over the Southeast US. We show that our model can reproduce the mean vertical profiles of major RON species and the total (NOy) in both 2004 and 2013. Among the major RON species, nitric acid (HNO3) is dominant (˜ 42-45 %), followed by NOx (31 %), total peroxy nitrates (ΣPNs; 14 %), and total alkyl nitrates (ΣANs; 9-12 %) on a regional scale. We find that most RON species, including NOx, ΣPNs, and HNO3, decline proportionally with decreasing NOx emissions in this region, leading to a similar decline in NOy. This linear response might be in part due to the nearly constant summertime supply of biogenic VOC emissions in this region. Our model captures the observed relative change in RON and surface ozone from 2004 to 2013. Model sensitivity tests indicate that further reductions of NOx emissions will lead to a continued decline in surface ozone and less frequent high-ozone events.

Top-down estimate of surface flux in the Los Angeles Basin using a mesoscale inverse modeling technique: assessing anthropogenic emissions of CO, NOx and CO2 and their impacts

NASA Astrophysics Data System (ADS)

Brioude, Jerome; Angevine, Wayne; Ahmadov, Ravan; Kim, Si Wan; Evan, Stephanie; McKeen, Stuart; Hsie, Eirh Yu; Frost, Greg; Neuman, Andy; Pollack, Ilana; Peischl, Jeff; Ryerson, Tom; Holloway, John; Brown, Steeve; Nowak, John; Roberts, Jim; Wofsy, Steeve; Santoni, Greg; Trainer, Michael

2013-04-01

We present top-down estimates of anthropogenic CO, NOx and CO2 surface fluxes at mesoscale using a Lagrangian model in combination with three different WRF model configurations, driven by data from aircraft flights during the CALNEX campaign in southern California in May-June 2010. The US EPA National Emission Inventory 2005 (NEI 2005) was the prior in the CO and NOx inversion calculations. The flux ratio inversion method, based on linear relationships between chemical species, was used to calculate the CO2 inventory without prior knowledge of CO2 surface fluxes. The inversion was applied to each flight to estimate the variability of single-flight-based flux estimates. In Los Angeles (LA) County, the uncertainties on CO and NOx fluxes were 10% and 15%, respectively. Compared with NEI 2005, the CO posterior emissions were lower by 43% ± 6% in LA County and by 37% ± 10% in the South Coast Air Basin (SoCAB). NOx posterior emissions were lower by 32% ± 10% in LA County and by 27% ± 15% in the SoCAB. NOx posterior emissions were 40% lower on weekends relative to weekdays. The CO2 posterior estimates were 183 ± 18 Tg yr-1 in SoCAB. A flight during ITCT in 2002 was used to estimate emissions in the LA Basin in 2002. From 2002 to 2010, the CO and NOx posterior emissions decreased by 41% and 37%, respectively, in agreement with previous studies. Over the same time period, CO2 emissions increased by 10% ± 14% in LA County but decreased by 4% ± 10% in the SoCAB, a statistically insignificant change. Overall, the posterior estimates were in good agreement with the California Air Resources Board (CARB) inventory, with differences of 15% or less. However, the posterior spatial distribution in the basin was significantly different from CARB for NOx emissions. WRF-Chem mesoscale chemical-transport model simulations allowed an evaluation of differences in chemistry using different inventory assumptions, including NEI 2005, CARB 2010 and the posterior inventories derived in this study. The biases in WRF-Chem ozone were reduced and correlations were increased using the posterior from this study compared with simulations with the two bottom-up inventories, showing that improving the spatial distribution of ozone precursor surface emissions is also important in mesoscale chemistry forecasts.

Top-down estimate of surface flux in the Los Angeles Basin using a mesoscale inverse modeling technique: assessing anthropogenic emissions of CO, NOx and CO2 and their impacts

NASA Astrophysics Data System (ADS)

Brioude, J.; Angevine, W. M.; Ahmadov, R.; Kim, S.-W.; Evan, S.; McKeen, S. A.; Hsie, E.-Y.; Frost, G. J.; Neuman, J. A.; Pollack, I. B.; Peischl, J.; Ryerson, T. B.; Holloway, J.; Brown, S. S.; Nowak, J. B.; Roberts, J. M.; Wofsy, S. C.; Santoni, G. W.; Trainer, M.

2012-12-01

We present top-down estimates of anthropogenic CO, NOx and CO2 surface fluxes at mesoscale using a Lagrangian model in combination with three different WRF model configurations, driven by data from aircraft flights during the CALNEX campaign in southern California in May-June 2010. The US EPA National Emission Inventory 2005 (NEI 2005) was the prior in the CO and NOx inversion calculations. The flux ratio inversion method, based on linear relationships between chemical species, was used to calculate the CO2 inventory without prior knowledge of CO2 surface fluxes. The inversion was applied to each flight to estimate the variability of single-flight-based flux estimates. In Los Angeles (LA) County, the uncertainties on CO and NOx fluxes were 10% and 15%, respectively. Compared with NEI 2005, the CO posterior emissions were lower by 43% ± 6% in LA County and by 37% ± 10% in the South Coast Air Basin (SoCAB). NOx posterior emissions were lower by 32% ± 10% in LA County and by 27% ± 15% in the SoCAB. NOx posterior emissions were 40% lower on weekends relative to weekdays. The CO2 posterior estimates were 183 ± 18 Tg yr-1 in SoCAB. A flight during ITCT in 2002 was used to estimate emissions in the LA Basin in 2002. From 2002 to 2010, the CO and NOx posterior emissions decreased by 41% and 37%, respectively, in agreement with previous studies. Over the same time period, CO2 emissions increased by 10% ± 14% in LA County but decreased by 4% ± 10% in the SoCAB, a statistically insignificant change. Overall, the posterior estimates were in good agreement with the California Air Resources Board (CARB) inventory, with differences of 15% or less. However, the posterior spatial distribution in the basin was significantly different from CARB for NOx emissions. WRF-Chem mesoscale chemical-transport model simulations allowed an evaluation of differences in chemistry using different inventory assumptions, including NEI 2005, CARB 2010 and the posterior inventories derived in this study. The biases in WRF-Chem ozone were reduced and correlations were increased using the posterior from this study compared with simulations with the two bottom-up inventories, showing that improving the spatial distribution of ozone precursor surface emissions is also important in mesoscale chemistry forecasts.

Regional Attribution of Ozone Production and Associated Radiative Forcing: a Step to Crediting NOx Emission Reductions

NASA Astrophysics Data System (ADS)

Naik, V.; Mauzerall, D. L.; Horowitz, L.; Schwarzkopf, D.; Ramaswamy, V.; Oppenheimer, M.

2004-12-01

The global distribution of tropospheric ozone (O3) depends on the location of emissions of its precursors in addition to chemical and dynamical factors. The global picture of O3 forcing is, therefore, a sum of regional forcings arising from emissions of precursors from different sources. The Kyoto Protocol does not include ozone as a greenhouse gas, and emission reductions of ozone precursors made under Kyoto or any similar agreement would presently receive no credit. In this study, we quantitatively estimate the contribution of emissions of nitrogen oxides (NOx), the primary limiting O3 precursor in the non-urban atmosphere, from specific countries and regions of the world to global O3 concentration distributions. We then estimate radiative forcing resulting from the regional perturbations of NOx emissions. This analysis is intended as an early step towards incorporating O3 into the Kyoto Protocol or any successor agreement. Under such a system countries could obtain credit for improvements in local air quality that result in reductions of O3 concentrations because of the associated reductions in radiative forcing. We use the global chemistry transport model, MOZART-2, to simulate the global O3 distribution for base year 1990 and perturbations to this distribution caused by a 10% percent reduction in the base emissions of NOx from the United States, Europe, East Asia, India, South America, and Africa. We calculate the radiative forcing for the simulated base and perturbed O3 distributions using the GFDL radiative transfer model. The difference between the radiative forcing from O3 for the base and perturbed distributions provides an estimate of the marginal radiative forcing from a region's emissions of NOx. We will present a quantitative analysis of the magnitude, spatial, and temporal distribution of radiative forcing resulting from marginal changes in the NOx emissions from each region.

Improving emissions inventories in North America through systematic analysis of model performance during ICARTT and MILAGRO

NASA Astrophysics Data System (ADS)

Mena, Marcelo Andres

During 2004 and 2006 the University of Iowa provided air quality forecast support for flight planning of the ICARTT and MILAGRO field campaigns. A method for improvement of model performance in comparison to observations is showed. The method allows identifying sources of model error from boundary conditions and emissions inventories. Simultaneous analysis of horizontal interpolation of model error and error covariance showed that error in ozone modeling is highly correlated to the error of its precursors, and that there is geographical correlation also. During ICARTT ozone modeling error was improved by updating from the National Emissions Inventory from 1999 and 2001, and furthermore by updating large point source emissions from continuous monitoring data. Further improvements were achieved by reducing area emissions of NOx y 60% for states in the Southeast United States. Ozone error was highly correlated to NOy error during this campaign. Also ozone production in the United States was most sensitive to NOx emissions. During MILAGRO model performance in terms of correlation coefficients was higher, but model error in ozone modeling was high due overestimation of NOx and VOC emissions in Mexico City during forecasting. Large model improvements were shown by decreasing NOx emissions in Mexico City by 50% and VOC by 60%. Recurring ozone error is spatially correlated to CO and NOy error. Sensitivity studies show that Mexico City aerosol can reduce regional photolysis rates by 40% and ozone formation by 5-10%. Mexico City emissions can enhance NOy and O3 concentrations over the Gulf of Mexico in up to 10-20%. Mexico City emissions can convert regional ozone production regimes from VOC to NOx limited. A method of interpolation of observations along flight tracks is shown, which can be used to infer on the direction of outflow plumes. The use of ratios such as O3/NOy and NOx/NOy can be used to provide information on chemical characteristics of the plume, such as age, and ozone production regime. Interpolated MTBE observations can be used as a tracer of urban mobile source emissions. Finally procedures for estimating and gridding emissions inventories in Brazil and Mexico are presented.

Assessment of Non-EGU NOx Emission Controls, Cost of Controls, and Time for Compliance Final TSD

EPA Pesticide Factsheets

The purpose of this Technical Support Document (TSD) is to discuss the currently available information on emissions and control measures for sources of NOX other than electric generating units (EGUs).

Mathematical optimization techniques for managing selective catalytic reduction for a fleet of coal-fired power plants

NASA Astrophysics Data System (ADS)

Alanis Pena, Antonio Alejandro

Major commercial electricity generation is done by burning fossil fuels out of which coal-fired power plants produce a substantial quantity of electricity worldwide. The United States has large reserves of coal, and it is cheaply available, making it a good choice for the generation of electricity on a large scale. However, one major problem associated with using coal for combustion is that it produces a group of pollutants known as nitrogen oxides (NO x). NOx are strong oxidizers and contribute to ozone formation and respiratory illness. The Environmental Protection Agency (EPA) regulates the quantity of NOx emitted to the atmosphere in the United States. One technique coal-fired power plants use to reduce NOx emissions is Selective Catalytic Reduction (SCR). SCR uses layers of catalyst that need to be added or changed to maintain the required performance. Power plants do add or change catalyst layers during temporary shutdowns, but it is expensive. However, many companies do not have only one power plant, but instead they can have a fleet of coal-fired power plants. A fleet of power plants can use EPA cap and trade programs to have an outlet NOx emission below the allowances for the fleet. For that reason, the main aim of this research is to develop an SCR management mathematical optimization methods that, with a given set of scheduled outages for a fleet of power plants, minimizes the total cost of the entire fleet of power plants and also maintain outlet NO x below the desired target for the entire fleet. We use a multi commodity network flow problem (MCFP) that creates edges that represent all the SCR catalyst layers for each plant. This MCFP is relaxed because it does not consider average daily NOx constraint, and it is solved by a binary integer program. After that, we add the average daily NOx constraint to the model with a schedule elimination constraint (MCFPwSEC). The MCFPwSEC eliminates, one by one, the solutions that do not satisfy the average daily NOx constraint and the worst NH 3 slip until it finds the solution that satisfies that requirement. We introduce an algorithm called heuristic MCFPwSEC (HMCFPwSEC). When HMCFPwSEC algorithm starts, we calculate the cost of the edges estimating the average NH3 slip level, but after we have a schedule that satisfies the average daily NOx constraint and the worst NH3 slip, we update the cost of the edges with the average NH3 slip for this schedule. We repeat this process until we have the solution. Because HMCFPwSEC does not guarantee optimality, we compare its results with SGO, which is optimal, using computational experiments. The results between both models are very similar, the only important difference is the time to solve each model. Then, a fleet HMCFPwSEC (FHMCFPwSEC) uses HMCFPwSEC to create the SCR management plan for each plant of the fleet, with a discrete NOx emissions value for each plant. FHMCFPwSEC repeats this process with different discrete levels of NOx emissions, for each plant, in order to create a new problem with schedules with different cost and NO x emissions for each plant of the fleet. Finally, FHMCFPwSEC solves this new problem with a binary integer program, in order to satisfy a NO x emission value for the fleet that also minimizes the total cost for the fleet, and using each plant once. FHMCFPwSEC can work with single cut and also with multi-cut methods. Because FHMCFPwSEC does not guarantee optimality, we compare its results with fleet SGO (FSGO) using computational experiments. The results between both models are very similar, the only important difference is the time to solve each model. In the experiments, FHMCFPwSEC multi-cut targeting new layer always uses less time than FSGO.

Cooking with Fire: The Mutagenicity- and PAH-Emission ...

EPA Pesticide Factsheets

Emissions from solid fuels used for cooking cause ~4 million premature deaths per year. Advanced solid-fuel cookstoves are a potential solution, but they should be assessed by appropriate performance indicators, including biological effects. We evaluated two categories of solid-fuel cookstoves for 8 pollutant- and 4 mutagenicity-emission factors, correlated the mutagenicity-emission factors, and compared them to those of other combustion emissions. We burned red oak in a 3-stone fire (TSF), a natural-draft stove (NDS), and a forced-draft stove (FDS); we combusted propane as a liquified petroleum gas control fuel. We determined emission factors based on useful energy (megajoules delivered, MJd) for carbon monoxide, nitrogen oxides (NOx), black carbon, methane, total hydrocarbons, 32 polycyclic aromatic hydrocarbons, PM2.5, levoglucosan (a wood-smoke marker), and mutagenicity in Salmonella. Other than NOx the emission factors per MJd correlated highly among each other (r2 ≥ 0.92); NOx correlated 0.58-0.76 with the other emission factors. Excluding NOx, the NDS and FDS reduced the emission factors on average 68 and 92%, respectively, relative to the TSF. Nonetheless, the mutagenicity-emission factor based on fuel energy used (MJthermal) for the most efficient stove (FDS) was intermediate to that of a large diesel bus engine and a small diesel generator. Both mutagenicity- and pollutant-emission factors may be informative for characterizing cookstove

Observations of the temperature dependent response of ozone to NOx reductions in the Sacramento, CA urban plume

NASA Astrophysics Data System (ADS)

Lafranchi, B. W.; Goldstein, A. H.; Cohen, R. C.

2011-02-01

Observations of NOx in the Sacramento, CA region show that mixing ratios decreased by 30% between 2001 and 2008. Here we use an observation-based method to quantify net ozone production rates in the outflow from the Sacramento metropolitan region and examine the O3 decrease resulting from reductions in NOx emissions. This observational method does not rely on assumptions about detailed chemistry of ozone production, rather it is an independent means to verify and test these assumptions. We use an instantaneous steady-state model as well as a detailed 1-D plume model to aid in interpretation of the ozone production inferred from observations. In agreement with the models, the observations show that early in the plume, the NOx dependence for Ox (Ox = O3 + NO2) production is strongly coupled with temperature, suggesting that temperature-dependent biogenic VOC emissions can drive Ox production between NOx-limited and NOx-suppressed regimes. As a result, NOx reductions were found to be most effective at higher temperatures over the 7 year period. We show that violations of the California 1-hour O3 standard (90 ppb) in the region have been decreasing linearly with decreases in NOx (at a given temperature) and predict that reductions of NOx concentrations (and presumably emissions) by an additional 30% (relative to 2007 levels) will eliminate violations of the state 1 h standard in the region. If current trends continue, a 30% decrease in NOx is expected by 2012, and an end to violations of the 1 h standard in the Sacramento region appears to be imminent.

Meteorological air quality forecasting using the WRF-Chem model during the LMOS2017 field campaign

NASA Astrophysics Data System (ADS)

Stanier, C. O.; Abdioskouei, M.; Carmichael, G. R.; Christiansen, M.; Sobhani, N.

2017-12-01

The Lake Michigan Ozone Study (LMOS 2017) occurred during May and June 2017 to address the high ozone episodes in coastal communities surrounding Lake Michigan. Aircraft, ship, mobile lab, and ground-based stations were used in this campaign to build an extensive dataset regarding ozone, its precursors, and particulate matter. The University of Iowa produced high-resolution (4x4 km2 horizontal resolution and 53 vertical levels) forecast products using the WRF-Chem modeling system in support of experimental planning during LMOS 2017. The base forecast system used WRF-Chem 3.6.1 and updated National Emission Inventory (NEI-2011v2). In the updated NEI-2011v2, we reduced the NOx emissions by 28% based on EPA's estimated NOx trends from 2011 to 2017. We ran another daily forecast (perturbed forecast) with 50% reduced NOx emission to capture the sensitivity of ozone to NOx emission and account for the impact of weekend emissions on ozone values. Preliminary in-field evaluation of model performance for clouds, on-shore flows, and surface and aircraft sampled ozone and NOx concentrations found that the model successfully captured much of the observed synoptic variability of onshore flows. The model captured the variability of O3 well, but underpredicted peak ozone during high O3 episodes. In post-campaign WRF-Chem simulations, we investigated the sensitivity of the model to the hydrocarbon emission.

A case study of the relative effects of power plant nitrogen oxides and sulfur dioxide emission reductions on atmospheric nitrogen deposition.

PubMed

Vijayaraghavan, Krish; Seigneur, Christian; Bronson, Rochelle; Chen, Shu-Yun; Karamchandani, Prakash; Walters, Justin T; Jansen, John J; Brandmeyer, Jo Ellen; Knipping, Eladio M

2010-03-01

The contrasting effects of point source nitrogen oxides (NOx) and sulfur dioxide (SO2) air emission reductions on regional atmospheric nitrogen deposition are analyzed for the case study of a coal-fired power plant in the southeastern United States. The effect of potential emission reductions at the plant on nitrogen deposition to Escambia Bay and its watershed on the Florida-Alabama border is simulated using the three-dimensional Eulerian Community Multiscale Air Quality (CMAQ) model. A method to quantify the relative and individual effects of NOx versus SO2 controls on nitrogen deposition using air quality modeling results obtained from the simultaneous application of NOx and SO2 emission controls is presented and discussed using the results from CMAQ simulations conducted with NOx-only and SO2-only emission reductions; the method applies only to cases in which ambient inorganic nitrate is present mostly in the gas phase; that is, in the form of gaseous nitric acid (HNO3). In such instances, the individual effects of NOx and SO2 controls on nitrogen deposition can be approximated by the effects of combined NOx + SO2 controls on the deposition of NOy, (the sum of oxidized nitrogen species) and reduced nitrogen species (NHx), respectively. The benefit of controls at the plant in terms of the decrease in nitrogen deposition to Escambia Bay and watershed is less than 6% of the overall benefit due to regional Clean Air Interstate Rule (CAIR) controls.

N+2 Advanced Low NOx Combustor Technology Final Report

NASA Technical Reports Server (NTRS)

Herbon, John; Aicholtz, John; Hsieh, Shih-Yang; Viars, Philip; Birmaher, Shai; Brown, Dan; Patel, Nayan; Carper, Doug; Cooper, Clay; Fitzgerald, Russell

2017-01-01

In accordance with NASAs technology goals for future subsonic vehicles, this contract identified and developed new combustor concepts toward meeting N+2 generation (2020) LTO (landing and take-off) NOx emissions reduction goal of 75 from the standard adopted at Committee on Aviation Environmental Protection 6 (CAEP6). Based on flame tube emissions, operability, and autoignition testing, one concept was down selected for sector testing at NASA. The N+2 combustor sector successfully demonstrated 75 reduction for LTO NOx (vs. CAEP6) and cruise NOx (vs. 2005 B777-200 reference) while maintaining 99.9 cruise efficiency and no increase in CO and HC emissions.The program also developed enabling technologies for the combustion system including ceramic matrix composites (CMC) liner materials, active combustion control concepts, and laser ignition for improved altitude relight.

Impact of the 2008 Global Recession on Air Quality over the United States: Implications for Surface Ozone Levels from Changes in NOx Emissions

NASA Technical Reports Server (NTRS)

Tong, Daniel; Pan, Li; Chen, Weiwei; Lamsal, Lok; Lee, Pius; Tang, Youhua; Kim, Hyuncheol; Kondragunta, Shobha; Stajner, Ivanka

2016-01-01

Satellite and ground observations detected large variability in nitrogen oxides (NOx) during the 2008 economic recession, but the impact of the recession on air quality has not been quantified. This study combines observed NOx trends and a regional chemical transport model to quantify the impact of the recession on surface ozone (O3) levels over the continental United States. The impact is quantified by simulating O3 concentrations under two emission scenarios: business-as-usual (BAU) and recession. In the BAU case, the emission projection from the Cross-State Air Pollution Rule is used to estimate the would-be NOx emission level in 2011. In the recession case, the actual NO2 trends observed from Air Quality System ground monitors and the Ozone Monitoring Instrument on the Aura satellite are used to obtain realistic changes in NOx emissions. The model prediction with the recession effect agrees better with ground O3 observations over time and space than the prediction with the BAU emission. The results show that the recession caused a 12ppbv decrease in surface O3 concentration over the eastern United States, a slight increase (0.51ppbv) over the Rocky Mountain region, and mixed changes in the Pacific West. The gain in air quality benefits during the recession, however, could be quickly offset by the much slower emission reduction rate during the post-recession period.

Cold-start and chemical characterization of emissions from mobile sources in Mexico.

PubMed

Schifter, I; Díaz, L; Rodríguez, R

2010-10-01

In this work tailpipe and evaporative emissions from a set of normal and high emitter vehicle models, year 2006-2008 (low mileage) certified when new to meet the Tier 1 emission standard, were characterized for criteria pollutants (carbon monoxide, nitrogen oxides and hydrocarbons), and a suite of unregulated emissions including aliphatic and aromatic aldehydes, monocyclic aromatic compounds, 1,3 butadiene, n-hexane and acrolein. Data were obtained under the three different driving conditions of the United States Federal Test Procedure, FTP-75 cycle. High emissions of both regulated and unregulated pollutants were observed in the cold-start phase of the driving cycle for low mileage Tier 1 normal and high emitters engines. Data were compared with results obtained for a set of MY > 1992-2005 that included vehicles with no catalytic converters, Tier 0 and MY 2000-5 Tier 1 emission standard with high mileage. The calculated average cold-start emissions for normal emitters in grams are 0.93, 8.21 and 1.06 for NMHC CO, and NOx, respectively for Tier 1 low mileage vehicles. The reductions in emissions for Tier 1 normal emitters are 76%, 56% and 56% for NMHC, CO and NOx, respectively, but 58%, 30% and 25% for the high emitters. Differences in emission can be ascribed to the mileage accumulation more than technological improvements. Cold-start emissions account in the USA roughly 10% of emissions from gasoline-powered vehicles. In Mexico the fractions are likely to be higher because one must account also for the contribution of Tier 0 and the running exhausts emissions of vehicles with no catalytic converters.

Speed correlation and emission of truck vehicles on dynamic conditions

NASA Astrophysics Data System (ADS)

Lutfie, M.; Samang, L.; Adisasmita, S. A.; Ramli, M. I.

2018-04-01

Concentration of CO2, NOx, smoke, CO, and HC released from several truck vehicles taken emission and speed data every 5 second through measurements using the mobile emission analyzer as an emission test vehicle that absorbs the gas from exhaust of sample vehicles. Implementation in field is to put emission test equipment on the right side of truck, which will absorb 5 gas compounds for 5 - 20 minutes with a view to knowing truck emissions of moving conditions by considering load factors. The sample vehicles are diesel-fueled trucks. From the research on gas emissions, it is generally found that the tendency that arises is the faster the vehicle speed then the CO2, NOx, Smoke, CO, and HC gases released will be greater or will increase as the vehicle speed increases. Thus, the relationship of CO2, NOx, smoke, CO, and HC concentration with vehicle speed is a linear relationship.

Multi-satellite sensor study on precipitation-induced emission pulses of NOx from soils in semi-arid ecosystems

NASA Astrophysics Data System (ADS)

Zörner, Jan; Penning de Vries, Marloes; Beirle, Steffen; Sihler, Holger; Veres, Patrick R.; Williams, Jonathan; Wagner, Thomas

2016-07-01

We present a top-down approach to infer and quantify rain-induced emission pulses of NOx ( ≡ NO + NO2), stemming from biotic emissions of NO from soils, from satellite-borne measurements of NO2. This is achieved by synchronizing time series at single grid pixels according to the first day of rain after a dry spell of prescribed duration. The full track of the temporal evolution several weeks before and after a rain pulse is retained with daily resolution. These are needed for a sophisticated background correction, which accounts for seasonal variations in the time series and allows for improved quantification of rain-induced soil emissions. The method is applied globally and provides constraints on pulsed soil emissions of NOx in regions where the NOx budget is seasonally dominated by soil emissions. We find strong peaks of enhanced NO2 vertical column densities (VCDs) induced by the first intense precipitation after prolonged droughts in many semi-arid regions of the world, in particular in the Sahel. Detailed investigations show that the rain-induced NO2 pulse detected by the OMI (Ozone Monitoring Instrument), GOME-2 and SCIAMACHY satellite instruments could not be explained by other sources, such as biomass burning or lightning, or by retrieval artefacts (e.g. due to clouds). For the Sahel region, absolute enhancements of the NO2 VCDs on the first day of rain based on OMI measurements 2007-2010 are on average 4 × 1014  molec cm-2 and exceed 1 × 1015  molec cm-2 for individual grid cells. Assuming a NOx lifetime of 4 h, this corresponds to soil NOx emissions in the range of 6 up to 65 ng N m-2 s-1, which is in good agreement with literature values. Apart from the clear first-day peak, NO2 VCDs are moderately enhanced (2 × 1014  molec cm-2) compared to the background over the following 2 weeks, suggesting potential further emissions during that period of about 3.3 ng N m-2 s-1. The pulsed emissions contribute about 21-44 % to total soil NOx emissions over the Sahel.

"Investigation of Trends in Aerosol Direct Radiative Effects ...

EPA Pesticide Factsheets

While aerosol radiative effects have been recognized as some of the largest sources of uncertainty among the forcers of climate change, there has been little effort devoted to verification of the spatial and temporal variability of the magnitude and directionality of aerosol radiative forcing. A comprehensive investigation of the processes regulating aerosol distributions, their optical properties, and their radiative effects and verification of their simulated effects for past conditions relative to measurements is needed in order to build confidence in the estimates of the projected impacts arising from changes in both anthropogenic forcing and climate change. This study aims at addressing this issue through a systematic investigation of changes in anthropogenic emissions of SO2 and NOx over the past two decades in the United States, their impacts on anthropogenic aerosol loading in the North American troposphere, and subsequent impacts on regional radiation budgets. During the period 1990-2010, SO2 and NOx emissions across the US have reduced by about 66% and 50%, respectively, mainly due to Title IV of the U.S. Clean Air Act Amendments (CAA). A methodology is developed to consistently estimate emission inventories for the 20-year period accounting for air quality regulations as well as population trends, economic conditions, and technology changes in motor vehicles and electric power generation. The coupled WRF-CMAQ model is applied for time periods pre a

Updates on Soil NOx parameterization in CMAQ v5.1

EPA Science Inventory

NOx has been well established to impact the formation of ozone and particulate matter. Soil NO emissions comprise approximately 20% of the global NOx budget and are a leading source of NOx in rural and remote areas. NO is emitted from soil as a result of complex biogeochemical i...

40 CFR 97.54 - Compliance.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 21 2011-07-01 2011-07-01 false Compliance. 97.54 Section 97.54... Compliance. (a) NOX allowance transfer deadline. The NOX allowances are available to be deducted for compliance with a unit's NOX Budget emissions limitation for a control period in a given year only if the NOX...

40 CFR 97.54 - Compliance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Compliance. 97.54 Section 97.54... Compliance. (a) NOX allowance transfer deadline. The NOX allowances are available to be deducted for compliance with a unit's NOX Budget emissions limitation for a control period in a given year only if the NOX...

40 CFR Appendix E to Part 75 - Optional NOX Emissions Estimation Protocol for Gas-Fired Peaking Units and Oil-Fired Peaking Units

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 17 2013-07-01 2013-07-01 false Optional NOX Emissions Estimation Protocol for Gas-Fired Peaking Units and Oil-Fired Peaking Units E Appendix E to Part 75 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTINUOUS EMISSION...

40 CFR Appendix E to Part 75 - Optional NOX Emissions Estimation Protocol for Gas-Fired Peaking Units and Oil-Fired Peaking Units

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 17 2014-07-01 2014-07-01 false Optional NOX Emissions Estimation Protocol for Gas-Fired Peaking Units and Oil-Fired Peaking Units E Appendix E to Part 75 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTINUOUS EMISSION...

40 CFR 75.72 - Determination of NOX mass emissions for common stack and multiple stack configurations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the hourly stack flow rate (in scfh). Only one methodology for determining NOX mass emissions shall be...-diluent continuous emissions monitoring system and a flow monitoring system in the common stack, record... maintain a flow monitoring system and diluent monitor in the duct to the common stack from each unit; or...

Experimental Investigation of a Multiplex Fuel Injector Module With Discrete Jet Swirlers for Low Emission Combustors

NASA Technical Reports Server (NTRS)

Tacina, Robert; Mao, Chien-Pei; Wey, Changlie

2004-01-01

A low-NOx emissions combustor concept has been demonstrated in flame-tube tests. A lean-direct injection (LDI) concept was used where the fuel is injected directly into the flame zone and the overall equivalence ratio of the mixture is lean. The LDI concept described in this report is a multiplex fuel injector module containing multipoint fuel injection tips and multi-burning zones. The injector module comprises 25 equally spaced injection tips within a 76 by 76 mm area that fits into the flame-tube duct. The air swirlers were made from a concave plate on the axis of the fuel injector using drilled holes at an angle to the axis of the fuel injector. The NOx levels were quite low and are greater than 70 percent lower than the 1996 ICAO standard. At an inlet temperature of 810 K, inlet pressure of 2760 kPa, pressure drop of 4 percent and a flame temperature of 1900 K with JP8 fuel, the NOx emission index was 9. The 25-point injector module exhibited the most uniform radial distribution of fuel-air mixture and NOx emissions in the flame tube when compared to other multipoint injection devices. A correlation is developed relating the NOx emissions to inlet temperature, inlet pressure, equivalence ratio and pressure drop.

40 CFR 86.127-12 - Test procedures; overview.

Code of Federal Regulations, 2012 CFR

2012-07-01

...: (1) Gaseous exhaust THC, NMHC, NMOG, CO, NOX, CO2, N2O, CH4, CH3OH, C2H5OH, C2H4O, and HCHO. (2... exhaust emission test is designed to determine gaseous THC, NMHC, NMOG, CO, CO2, CH4, NOX, N2O, and... THC using a heated sample line and analyzer; the other gaseous emissions (CH4, CO, CO2, N2O, and NOX...

40 CFR 86.127-12 - Test procedures; overview.

Code of Federal Regulations, 2013 CFR

2013-07-01

...: (1) Gaseous exhaust THC, NMHC, NMOG, CO, NOX, CO2, N2O, CH4, CH3OH, C2H5OH, C2H4O, and HCHO. (2... exhaust emission test is designed to determine gaseous THC, NMHC, NMOG, CO, CO2, CH4, NOX, N2O, and... THC using a heated sample line and analyzer; the other gaseous emissions (CH4, CO, CO2, N2O, and NOX...

40 CFR 86.127-12 - Test procedures; overview.

Code of Federal Regulations, 2014 CFR

2014-07-01

...: (1) Gaseous exhaust THC, NMHC, NMOG, CO, NOX, CO2, N2O, CH4, CH3OH, C2H5OH, C2H4O, and HCHO. (2... exhaust emission test is designed to determine gaseous THC, NMHC, NMOG, CO, CO2, CH4, NOX, N2O, and... THC using a heated sample line and analyzer; the other gaseous emissions (CH4, CO, CO2, N2O, and NOX...

40 CFR Appendix I to Part 1054 - Summary of Previous Emission Standards

Code of Federal Regulations, 2014 CFR

2014-07-01

... Engines (g/kW-hr) a Engine displacement class HC NOX CO Class III 295 5.36 805 Class IV 241 5.36 805 Class...—Phase 2 Emission Standards for Handheld Engines (g/kW-hr) a Engine displacement class HC+NOX CO Class...-hr) a Engine displacement class HC+NOX CO Class I 16.1 519 Class II 13.4 519 a Phase 1 standards are...

40 CFR Appendix I to Part 1054 - Summary of Previous Emission Standards

Code of Federal Regulations, 2012 CFR

2012-07-01

... Engines (g/kW-hr) a Engine displacement class HC NOX CO Class III 295 5.36 805 Class IV 241 5.36 805 Class...—Phase 2 Emission Standards for Handheld Engines (g/kW-hr) a Engine displacement class HC+NOX CO Class...-hr) a Engine displacement class HC+NOX CO Class I 16.1 519 Class II 13.4 519 a Phase 1 standards are...

40 CFR Appendix I to Part 1054 - Summary of Previous Emission Standards

Code of Federal Regulations, 2013 CFR

2013-07-01

... Engines (g/kW-hr) a Engine displacement class HC NOX CO Class III 295 5.36 805 Class IV 241 5.36 805 Class...—Phase 2 Emission Standards for Handheld Engines (g/kW-hr) a Engine displacement class HC+NOX CO Class...-hr) a Engine displacement class HC+NOX CO Class I 16.1 519 Class II 13.4 519 a Phase 1 standards are...

40 CFR Appendix I to Part 1054 - Summary of Previous Emission Standards

Code of Federal Regulations, 2010 CFR

2010-07-01

... Engines (g/kW-hr) a Engine displacement class HC NOX CO Class III 295 5.36 805 Class IV 241 5.36 805 Class...—Phase 2 Emission Standards for Handheld Engines (g/kW-hr) a Engine displacement class HC+NOX CO Class...-hr) a Engine displacement class HC+NOX CO Class I 16.1 519 Class II 13.4 519 a Phase 1 standards are...

40 CFR Appendix I to Part 1054 - Summary of Previous Emission Standards

Code of Federal Regulations, 2011 CFR

2011-07-01

... Engines (g/kW-hr) a Engine displacement class HC NOX CO Class III 295 5.36 805 Class IV 241 5.36 805 Class...—Phase 2 Emission Standards for Handheld Engines (g/kW-hr) a Engine displacement class HC+NOX CO Class...-hr) a Engine displacement class HC+NOX CO Class I 16.1 519 Class II 13.4 519 a Phase 1 standards are...

Effective NOx remediation from a surrogate flue gas using the US NRL Electra electron beam facility

NASA Astrophysics Data System (ADS)

Petrova, Tz. B.; Petrov, G. M.; Wolford, M. F.; Giuliani, J. L.; Ladouceur, H. D.; Hegeler, F.; Myers, M. C.; Sethian, J. D.

2017-02-01

Nitric oxide (NOx) emission is under restrictive federal regulations because of its negative impact on atmosphere, biosphere, and human health. Therefore, its removal has been a subject of extensive research to develop new efficient and cost effective techniques that can be applied on an industrial scale. In this work, we study both experimentally and theoretically an effective removal of NOx pollutants from a surrogate flue gas (SFG) using high power electron beam (e-beam) pulses. SFG is a simulant for exhaust from coal combustion power plants (82% N2, 6% O2, 12% CO2, and ˜100 ppm of NOx). The pulsed electron beam is generated using the United States Naval Research Laboratory Electra facility, which delivers e-beams with energies of ˜500 keV and a power pulse duration of ˜140 ns. During the e-beam irradiation, the energetic electrons generate a non-equilibrium plasma containing chemically active species, which then react with NOx to form harmless substances. A non-equilibrium time-dependent model is developed to describe NOx remediation from SFG. The model combines e-beam deposition rates obtained by solving the electron Boltzmann equation and extensive plasma chemistry modeling, which follows the species on a time scale from sub-nanoseconds to a few seconds. NOx decomposition as a function of electron beam parameters is studied. It is demonstrated experimentally that short (ns) pulses are the most efficient for NOx removal. A sharp reduction of NOx was measured with e-beam power deposition increasing, following the trend predicted by the model, achieving a 20 fold reduction to ˜5 ppm at energy deposition ˜20 J/l.

N2O and NO2 Emissions from Heavy-Duty Diesel Trucks with Advanced Emission Controls

NASA Astrophysics Data System (ADS)

Preble, C.; Harley, R.; Kirchstetter, T.

2014-12-01

Diesel engines are the largest source of nitrogen oxides (NOx) emissions nationally, and also a major contributor to the black carbon (BC) fraction of fine particulate matter (PM). Recently, diesel particle filter (DPF) and selective catalytic reduction (SCR) emission control systems that target exhaust PM and NOx have become standard equipment on new heavy-duty diesel trucks. However, the deliberate catalytic oxidation of engine-out nitric oxide (NO) to nitrogen dioxide (NO2) in continuously regenerating DPFs leads to increased tailpipe emission of NO2. This is of potential concern due to the toxicity of NO2 and the resulting increases in atmospheric formation of other air pollutants such as ozone, nitric acid, and fine PM. While use of SCR reduces emissions of both NO and NO2, it may lead to increased emissions of nitrous oxide (N2O), a potent greenhouse gas. Here we report results from on-road measurements of heavy-duty diesel truck emissions conducted at the Port of Oakland and the Caldecott Tunnel in the San Francisco Bay Area. Emission factors (g pollutant per kg of diesel) were linked via recorded license plates to individual truck attributes, including engine model year and installed emission control equipment. Between 2009 and 2013, the fraction of DPF-equipped trucks at the Port of Oakland increased from 2 to 99%, and median engine age decreased from 11 to 6 years. Over the same period, fleet-average emission factors for black carbon and NOx decreased by 76 ± 22% and 53 ± 8%, respectively. However, direct emissions of NO2 increased, and consequently the NO2/NOx emission ratio increased from 0.03 ± 0.02 to 0.18 ± 0.03. Older trucks retrofitted with DPFs emitted approximately 3.5 times more NO2 than newer trucks equipped with both DPF and SCR. Preliminary data from summer 2014 measurements at the Caldecott Tunnel suggest that some older trucks have negative emission factors for N2O, and that for newer trucks, N2O emission factors have changed sign and are significantly increased. More comprehensive analysis of the effects of SCR on diesel NOx and N2O emissions will be reported in the presentation. These on-road emission studies indicate that advanced emission control systems such as DPF and SCR dramatically reduce PM and NOx emissions, but can cause undesirable side effects like increased NO2 and N2O emissions.

Flexible NO(x) abatement from power plants in the eastern United States.

PubMed

Sun, Lin; Webster, Mort; McGaughey, Gary; McDonald-Buller, Elena C; Thompson, Tammy; Prinn, Ronald; Ellerman, A Denny; Allen, David T

2012-05-15

Emission controls that provide incentives for maximizing reductions in emissions of ozone precursors on days when ozone concentrations are highest have the potential to be cost-effective ozone management strategies. Conventional prescriptive emissions controls or cap-and-trade programs consider all emissions similarly regardless of when they occur, despite the fact that contributions to ozone formation may vary. In contrast, a time-differentiated approach targets emissions reductions on forecasted high ozone days without imposition of additional costs on lower ozone days. This work examines simulations of such dynamic air quality management strategies for NO(x) emissions from electric generating units. Results from a model of day-specific NO(x) pricing applied to the Pennsylvania-New Jersey-Maryland (PJM) portion of the northeastern U.S. electrical grid demonstrate (i) that sufficient flexibility in electricity generation is available to allow power production to be switched from high to low NO(x) emitting facilities, (ii) that the emission price required to induce EGUs to change their strategies for power generation are competitive with other control costs, (iii) that dispatching strategies, which can change the spatial and temporal distribution of emissions, lead to ozone concentration reductions comparable to other control technologies, and (iv) that air quality forecasting is sufficiently accurate to allow EGUs to adapt their power generation strategies.

Impacts of Interannual Variability in Biogenic VOC Emissions near Transitional Ozone Production Regimes

NASA Astrophysics Data System (ADS)

Geddes, J.

2017-12-01

Due to successful NOx emission controls, summertime ozone production chemistry in urban areas across North America is transitioning from VOC-limited to increasingly NOx-limited. In some regions where ozone production sensitivity is in transition, interannual variability in surrounding biogenic VOC emissions could drive fluctuations in the prevailing chemical regime and modify the impact of anthropogenic emission changes. I use satellite observations of HCHO and NO2 column density, along with a long-term simulation of atmospheric chemistry, to investigate the impact of interannual variability in biogenic isoprene sources near large metro areas. Peak emissions of isoprene in the model can vary by up to 20-60% in any given year compared to the long term mean, and this variability drives the majority of the variability in simulated local HCHO:NO2 ratios (a common proxy for ozone production sensitivity). The satellite observations confirm increasingly NOx-limited chemical regimes with large interannual variability. In several instances, the model and satellite observations suggest that variability in biogenic isoprene emissions could shift summertime ozone production from generally VOC- to generally NOx- sensitive (or vice versa). This would have implications for predicting the air quality impacts of anthropogenic emission changes in any given year, and suggests that drivers of biogenic emissions need to be well understood.

Impact of emission control on regional air quality in the Pearl Delta River region, southern China

NASA Astrophysics Data System (ADS)

Wang, N.; Xuejiao, D.

2017-12-01

The Pearl River Delta (PRD) in China has been suffering from air quality issues and the government has implemented a series of strategies in controlling emissions. In an attempt to provide scientific support for improving air quality, the paper investigates the concerning past-to-present air quality data and assesses air quality resulting from emission control. Statistical data revealed that energy consumption doubled from 2004 to 20014 and vehicle usage increased significantly from 2006 to 2014. Due to the effect of control efforts, primary emission of SO2, NOx and PM2.5 decreased resulting in ambient concentrations of SO2, NO2 and PM10 decreased by 66%, 20% and 24%, respectively. However, O3 increased 19% because of the increase of VOC emission. A chemical transport model, the Community Multi-scale Air Quality, was employed to evaluate the responses of nitrate, ammonium, SOA, PM2.5 and O3 to changes in NOx, VOC and NH3 emissions. Three scenarios, a baseline scenario, a CAP scenario (control strength followed as past tendency), and a REF scenario (strict control referred to latest policy and plans), were conducted to investigate the responses and mechanisms. NOx controlling scenarios showed that NOx, nitrate and PM2.5 reduced by 1.8%, 0.7% and 0.2% under CAP and reduced by 7.2%, 1.8% and 0.3% under REF, respectively. The results indicated that reducing NOx emission caused the increase of atmospheric oxidizability, which might result in a compensation of PM2.5 due to the increase of nitrate or sulfate. NH3 controlling scenarios showed that nitrate was sensitive to NH3 emission in PRD, with nitrate decreased by 0 - 10.6% and 0 - 48% under CAP and REF, respectively. Since controlling NH3 emissions not only reduced ammonium but also significantly reduced nitrate, the implement of NH3 controlling strategy was highly suggested. The VOC scenarios revealed that though SOA was not the major component of PM2.5, controlling VOC emission might take effect in southwestern PRD where photochemical pollution usually occurred. Last but not least, the responses of O3 indicated that the PRD was generally VOC-sensitive, while the regime turned to NOx-sensitive in the afternoon, therefore controlling VOC emission could reduce the overall O3 and controlling NOx emission in the afternoon could reduce peak O3.

A combined approach for the evaluation of a volatile organic compound emissions inventory.

PubMed

Choi, Yu-Jin; Calabrese, Richard V; Ehrman, Sheryl H; Dickerson, Russell R; Stehr, Jeffrey W

2006-02-01

Emissions inventories significantly affect photochemical air quality model performance and the development of effective control strategies. However, there have been very few studies to evaluate their accuracy. Here, to evaluate a volatile organic compound (VOC) emissions inventory, we implemented a combined approach: comparing the ratios of carbon bond (CB)-IV VOC groups to nitrogen oxides (NOx) or carbon monoxide (CO) using an emission preprocessing model, comparing the ratios of VOC source contributions from a source apportionment technique to NOx or CO, and comparing ratios of CB-IV VOC groups to NOx or CO and the absolute concentrations of CB-IV VOC groups using an air quality model, with the corresponding ratios and concentrations observed at three sites (Maryland, Washington, DC, and New Jersey). The comparisons of the ethene/NOx ratio, the xylene group (XYL)/NOx ratio, and ethene and XYL concentrations between estimates and measurements showed some differences, depending on the comparison approach, at the Maryland and Washington, DC sites. On the other hand, consistent results at the New Jersey site were observed, implying a possible overestimation of vehicle exhaust. However, in the case of the toluene group (TOL), which is emitted mainly from surface coating and printing sources in the solvent utilization category, the ratios of TOL/ NOx or CO, as well as the absolute concentrations revealed an overestimate of these solvent sources by a factor of 1.5 to 3 at all three sites. In addition, the overestimate of these solvent sources agreed with the comparisons of surface coating and printing source contributions relative to NOx from a source apportionment technique to the corresponding value of estimates at the Maryland site. Other studies have also suggested an overestimate of solvent sources, implying a possibility of inaccurate emission factors in estimating VOC emissions from surface coating and printing sources. We tested the impact of these overestimates with a chemical transport model and found little change in ozone but substantial changes in calculated secondary organic aerosol concentrations.

Air-pollution emission control in China: impacts on soil acidification recovery and constraints due to drought.

PubMed

Duan, Lei; Liu, Jing; Xin, Yan; Larssen, Thorjørn

2013-10-01

The Chinese government has established compulsory targets to reduce sulfur dioxide (SO2) and nitrogen oxide (NOx) emissions by 8% and 10%, respectively, during 2010-2015. In this study, the effect of the policy was evaluated by predicting the recovery of acidified forest soil in Chongqing, an area severely impacted by acid rain in southwest China. Since precipitation has decreased significantly in this area in recent years, the impact of drought on soil acidification was also considered. A dynamic acidification model, MAGIC, was used to predict future trends in soil chemistry under different scenarios for deposition reduction as well as drought. We found that the current regulation of SO2 emission abatement did not significantly increase soil water pH values, the Ca2+ to Al3+ molar ratio (Ca/Al), or soil base saturation to the level of 2000 before 2050. NOx emission control would have less of an effect on acidification recovery, while emission reduction of particulate matter could offset the benefits of SO2 reduction by greatly decreasing the deposition of base cations, particularly Ca(2+). Continuous droughts in the future might also delay acidification recovery. Therefore, more stringent SO2 emission control should be implemented to facilitate the recovery of seriously acidified areas in China. © 2013 Elsevier B.V. All rights reserved.

Low NOx heavy fuel combustor concept program

NASA Technical Reports Server (NTRS)

White, D. J.; Lecren, R. T.; Batakis, A. P.

1981-01-01

A total of twelve low NOx combustor configurations, embodying three different combustion concepts, were designed and fabricated as modular units. These configurations were evaluated experimentally for exhaust emission levels and for mechanical integrity. Emissions data were obtained in depth on two of the configurations.

Control of diesel soot and NOx emissions with a particulate trap and EGR.

PubMed

Liu, Rui-xiang; Gao, Xi-yan; Yang, De-sheng; Xu, Xiao-guang

2005-01-01

The exhaust gas recirculation (EGR), coupled with a high-collection efficiency particulate trap to simultaneously control smoke and NOx emissions from diesel engines were studied. This ceramic trap developed previously provided the soot cleaning efficiency of 99%, the regeneration efficiency reaches 80% and the ratio of success reaches 97%, which make EGR used in diesel possible. At the presence of EGR, opening of the regeneration control valve of the trap was over again optimized to compensate for the decrease of the oxygen concentration in the exhaust gas resulted from EGR. The results indicated the cleaning efficiency and regeneration performance of the trap were maintained at the same level except that the back pressure increased faster. A new EGR system was developed, which is based on a wide range oxygen (UEGO) sensor. Experiments were carried out under steady state conditions while maintaining the engine speed at 1600 r/min, setting the engine loads at 0%, 25%, 50%, 75% and 100% respectively. Throughout each test the EGR rate was kept at nine different settings and data were taken with the gas analyzer and UEGO sensor. Then, the EGR rate and engine load maps, which showed the tendencies of NOx, CO and HC emissions from diesel engine, were made using the measured data. Using the maps, the author set up the EGR regulation, the relationship between the optimal amounts of EGR flow and the equivalence ratio, sigma, where sigma = 14.5/AFR.

Impact of passenger car NOX emissions on urban NO2 pollution - Scenario analysis for 8 European cities

NASA Astrophysics Data System (ADS)

Degraeuwe, Bart; Thunis, Philippe; Clappier, Alain; Weiss, Martin; Lefebvre, Wouter; Janssen, Stijn; Vranckx, Stijn

2017-12-01

Residents of large European cities are exposed to NO2 concentrations that often exceed the established air quality standards. Diesel cars have been identified as a major contributor to this situation; yet, it remains unclear to which levels the NOX emissions of diesel cars have to decrease to effectively mitigate urban NO2 pollution across Europe. Here, we take a continental perspective and model urban NO2 pollution in a generic street canyon of 8 major European cities for various NOX emission scenarios. We find that a reduction in the on-road NOX emissions of diesel cars to the Euro 6 level can in general decrease the regional and urban NO2 concentrations and thereby the frequency of exceedances of the NO2 air quality standard. High NO2 fractions in the NOX emissions of diesel cars tend to increase the urban NO2 concentrations only in proximity of intense road traffic typically found on artery roads in large cities like Paris and London. In cities with a low share of diesel cars in the vehicle fleet such as Athens or a high contribution from the NO2 background to the urban NO2 pollution such as Krakow, measures addressing heavy-duty vehicles, and the manufacturing, energy, and mining industry are necessary to decrease urban air pollution. We regard our model results as robust albeit subject to uncertainty resulting from the application of a generic street layout. With small modifications in the input parameters, our model could be used to assess the impact of NOX emissions from road transport on NO2 air pollution in any European city.

Flame Tube NOx Emissions Using a Lean-Direct-Wall-Injection Combustor Concept

NASA Technical Reports Server (NTRS)

Tacina, Robert R.; Wey, Changlie; Choi, Kyung J.

2001-01-01

A low-NOx emissions combustor concept has been demonstrated in flame tube tests. A lean-direct injection concept was used where the fuel is injected directly into the flame zone and the overall fuel-air mixture is lean. In this concept the air is swirled upstream of a venturi section and the fuel is injected radially inward into the air stream from the throat section using a plain-orifice injector. Configurations have two-, four-, or six-wall fuel injectors and in some cases fuel is also injected from an axially located simplex pressure atomizer. Various orifice sizes of the plain-orifice injector were evaluated for the effect on NOx. Test conditions were inlet temperatures up to 8 1 OK, inlet pressures up to 2760 kPa, and flame temperatures up to 2100 K. A correlation is developed relating the NOx emissions to inlet temperature, inlet pressure, fuel-air ratio and pressure drop. Assuming that 15 percent of the combustion air would be used for liner cooling and using an advanced engine cycle, for the best configuration, the NOx emissions using the correlation is estimated to be <75 percent of the 1996 ICAO standard.

Influence of the overfire air ratio on the NO(x) emission and combustion characteristics of a down-fired 300-MW(e) utility boiler.

PubMed

Ren, Feng; Li, Zhengqi; Chen, Zhichao; Fan, Subo; Liu, Guangkui

2010-08-15

Down-fired boilers used to burn low-volatile coals have high NO(x) emissions. To find a way of solving this problem, an overfire air (OFA) system was introduced on a 300 MW(e) down-fired boiler. Full-scale experiments were performed on this retrofitted boiler to explore the influence of the OFA ratio (the mass flux ratio of OFA to the total combustion air) on the combustion and NO(x) emission characteristics in the furnace. Measurements were taken of gas temperature distributions along the primary air and coal mixture flows, average gas temperatures along the furnace height, concentrations of gases such as O(2), CO, and NO(x) in the near-wall region and carbon content in the fly ash. Data were compared for five different OFA ratios. The results show that as the OFA ratio increases from 12% to 35%, the NO(x) emission decreases from 1308 to 966 mg/Nm(3) (at 6% O(2) dry) and the carbon content in the fly ash increases from 6.53% to 15.86%. Considering both the environmental and economic effect, 25% was chosen as the optimized OFA ratio.

Effects of co-processing sewage sludge in cement kiln on NOx, NH3 and PAHs emissions.

PubMed

Lv, Dong; Zhu, Tianle; Liu, Runwei; Lv, Qingzhi; Sun, Ye; Wang, Hongmei; Liu, Yu; Zhang, Fan

2016-09-01

The effects of co-processing sewage sludge in cement kiln on NOx, NH3 and PAHs emissions were systematically investigated in a cement production line in Beijing. The results show that co-processing the sewage sludge was helpful to reduce NOx emission, which primarily depends on the NH3 amount released from the sewage sludge. Meanwhile, NOx and NH3 concentrations in the flue gas have a negative correlation, and the contribution of feeding the sewage sludge to NOx removal decreased with the increase of injection amount of ammonia water in the SNCR system. Therefore, it is suggested that the injection amount of ammonia water in SNCR system may reduce to cut down the operating costs during co-processing the sewage sludge in cement kiln. In addition, the emission of total PAHs seems to increase with the increased amount of the sewage sludge feeding to the cement kiln. However, the distributions of PAHs were barely changed, and lower molecular weight PAHs were mainly distributed in gaseous phase, accounted for the major portion of PAHs when co-processing sewage sludge in cement kiln. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effects of Retrofitting Emission Control Systems on all In-Use Heavy Diesel Trucks

NASA Astrophysics Data System (ADS)

Millstein, D.; Harley, R. A.

2009-12-01

Diesel exhaust is now the largest source of nitrogen oxide (NOx) emissions nationally in the US, and contributes significantly to emissions of fine particulate black carbon (soot) as well. New national standards call for dramatically lower emissions of exhaust particulate matter (PM) and NOx from new diesel engines starting in 2007 and 2010, respectively. Unfortunately it will take decades for the cleaner new engines to replace those currently in service on existing heavy-duty trucks. The state of California recently adopted a rule to accelerate fleet turnover in the heavy-duty truck sector, requiring that all in-use trucks meet the new exhaust PM standards by 2014. This will entail retrofit of diesel particle filters or replacement for over a million existing diesel engines. Diesel particle filters can replace the muffler on existing trucks, and there is extensive experience with retrofit of this control equipment on public sector fleets such as diesel-powered transit buses. Nitrogen dioxide (NO2) is used as an oxidizing agent to remove carbon particles from the particle filter, to prevent it from becoming plugged. To create the needed NO2, NOx already present in engine exhaust as nitric oxide (NO) is deliberately oxidized to NO2 upstream of the particle filter using a platinum catalyst. The NO2/NOx ratio in exhaust emissions therefore increases to ~35% in comparison to much lower values (~5%) typical of older engines without particle filters. We evaluate the effects on air quality of increased use of diesel particle traps and NOx controls in southern California using the Community Multiscale Air Quality (CMAQ) model. Compared to a reference scenario without the retrofit program, we found black carbon concentrations decreased by ~20%, with small increases (4%) in ambient ozone concentrations. During summer, average NO2 concentrations decrease despite the increase in primary NO2 emissions - because total NOx emissions are reduced as part of a parallel but more gradual program to retrofit NOx control systems on in-use engines. During winter, NO2 concentrations increase by 1-2% at locations with high diesel truck traffic, and larger increases may occur if diesel trucks outfitted with particle traps do not meet the in-use NOx emission reduction requirements. Small changes to fine particulate nitrate are seen as well with increases over the Los Angeles area of 3 and 6% during the summer and fall, respectively. During the summer, but not the fall, downwind nitrate decreased by 2% east of Los Angeles near Riverside. Emissions reductions due to fleet turnover in the reference scenario (without retrofit) may be optimistic, and the air quality benefits of retrofits could therefore be understated, due to slow sales of new engines in recent years. In any case, significant changes in diesel engine emissions of NOx and PM are expected to occur over the next 5 years in California.

Application of positive matrix factorization to on-road measurements for source apportionment of diesel- and gasoline-powered vehicle emissions in Mexico City

NASA Astrophysics Data System (ADS)

Thornhill, D. A.; Williams, A. E.; Onasch, T. B.; Wood, E.; Herndon, S. C.; Kolb, C. E.; Knighton, W. B.; Zavala, M.; Molina, L. T.; Marr, L. C.

2009-12-01

The goal of this research is to quantify diesel- and gasoline-powered motor vehicle emissions within the Mexico City Metropolitan Area (MCMA) using on-road measurements captured by a mobile laboratory combined with positive matrix factorization (PMF) receptor modeling. During the MCMA-2006 ground-based component of the MILAGRO field campaign, the Aerodyne Mobile Laboratory (AML) measured many gaseous and particulate pollutants, including carbon dioxide, carbon monoxide (CO), nitrogen oxides (NOx), benzene, toluene, alkylated aromatics, formaldehyde, acetaldehyde, acetone, ammonia, particle number, fine particulate mass (PM2.5), and black carbon (BC). These serve as inputs to the receptor model, which is able to resolve three factors corresponding to gasoline engine exhaust, diesel engine exhaust, and the urban background. Using the source profiles, we calculate fuel-based emission factors for each type of exhaust. The MCMA's gasoline-powered vehicles are considerably dirtier, on average, than those in the US with respect to CO and aldehydes. Its diesel-powered vehicles have similar emission factors of NOx and higher emission factors of aldehydes, particle number, and BC. In the fleet sampled during AML driving, gasoline-powered vehicles are responsible for 97% of mobile source emissions of CO, 22% of NOx, 95-97% of aromatics, 72-85% of carbonyls, 74% of ammonia, negligible amounts of particle number, 26% of PM2.5, and 2% of BC; diesel-powered vehicles account for the balance. Because the mobile lab spent 17% of its time waiting at stoplights, the results may overemphasize idling conditions, possibly resulting in an underestimate of NOx and overestimate of CO emissions. On the other hand, estimates of the inventory that do not correctly account for emissions during idling are likely to produce bias in the opposite direction. Nevertheless, the fuel-based inventory suggests that mobile source emissions of CO and NOx are overstated in the official inventory while emissions of VOCs may be understated. For NOx, the fuel-based inventory is lower for gasoline-powered vehicles but higher for diesel-powered ones compared to the official inventory.

Analysis of Strategies for Multiple Emissions from Electric Power SO2, NOX, CO2, Mercury and RPS

EIA Publications

2001-01-01

At the request of the Subcommittee, the Energy Information Administration prepared an initial report that focused on the impacts of reducing power sector NOx, SO2, and CO2 emissions. The current report extends the earlier analysis to add the impacts of reducing power sector mercury emissions and introducing renewable portfolio standard (RPS) requirements.

40 CFR 51.122 - Emissions reporting requirements for SIP revisions relating to budgets for NOX emissions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... NOX emissions data as described in this section. (c) Each revision must provide for periodic reporting...) of this section. (3) Through 2011, reports are to be submitted according to the schedule in Table 1... reports are to be submitted each year that a triennial report is not required. Table 1—Schedule for...

40 CFR 52.38 - What are the requirements of the Federal Implementation Plans (FIPs) under the Transport Rule (TR...

Code of Federal Regulations, 2013 CFR

2013-07-01

... Federal Implementation Plans (FIPs) under the Transport Rule (TR) relating to emissions of nitrogen oxides... emissions of nitrogen oxides? (a)(1) The TR NOX Annual Trading Program provisions set forth in subpart AAAAA... annual emissions of nitrogen oxides (NOX). (2) The provisions of subpart AAAAA of part 97 of this chapter...

40 CFR 52.38 - What are the requirements of the Federal Implementation Plans (FIPs) under the Transport Rule (TR...

Code of Federal Regulations, 2014 CFR

2014-07-01

... Federal Implementation Plans (FIPs) under the Transport Rule (TR) relating to emissions of nitrogen oxides... emissions of nitrogen oxides? (a)(1) The TR NOX Annual Trading Program provisions set forth in subpart AAAAA... annual emissions of nitrogen oxides (NOX). (2) The provisions of subpart AAAAA of part 97 of this chapter...

40 CFR 52.38 - What are the requirements of the Federal Implementation Plans (FIPs) under the Transport Rule (TR...

Code of Federal Regulations, 2012 CFR

2012-07-01

... Federal Implementation Plans (FIPs) under the Transport Rule (TR) relating to emissions of nitrogen oxides... emissions of nitrogen oxides? (a)(1) The TR NOX Annual Trading Program provisions set forth in subpart AAAAA... annual emissions of nitrogen oxides (NOX). (2) The provisions of subpart AAAAA of part 97 of this chapter...

40 CFR 60.45 - Emissions and fuel monitoring.

Code of Federal Regulations, 2014 CFR

2014-07-01

... oil) with potential SO2 emissions rates of 26 ng/J (0.060 lb/MMBtu) or less and that does not use post... of a CEMS for NOX may be delayed until after the initial performance tests under § 60.8 have been conducted. If the owner or operator demonstrates during the performance test that emissions of NOX are less...

40 CFR 60.45 - Emissions and fuel monitoring.

Code of Federal Regulations, 2013 CFR

2013-07-01

... oil) with potential SO2 emissions rates of 26 ng/J (0.060 lb/MMBtu) or less and that does not use post... of a CEMS for NOX may be delayed until after the initial performance tests under § 60.8 have been conducted. If the owner or operator demonstrates during the performance test that emissions of NOX are less...

40 CFR 60.45 - Emissions and fuel monitoring.

Code of Federal Regulations, 2012 CFR

2012-07-01

... oil) with potential SO2 emissions rates of 26 ng/J (0.060 lb/MMBtu) or less and that does not use post... of a CEMS for NOX may be delayed until after the initial performance tests under § 60.8 have been conducted. If the owner or operator demonstrates during the performance test that emissions of NOX are less...

NOx emissions from a Central California dairy

NASA Astrophysics Data System (ADS)

Hasson, Alam S.; Ogunjemiyo, Segun O.; Trabue, Steven; Ashkan, Shawn; Scoggin, Kenwood; Steele, Julie; Olea, Catalina; Middala, Srikar; Vu, Kennedy; Scruggs, Austen; Addala, Laxmi R.; Nana, Lucien

2013-05-01

Concentrations of NOx (NO + NO2) were monitored downwind from a Central California dairy facility during 2011 and 2012. NOx concentrations at the dairy were significantly higher than the background levels during August 2011 primarily due to the presence of elevated NO, but were indistinguishable from background concentrations during January and April 2012. A Gaussian plume model (AERMOD) and a Lagrangian back trajectory model (Wind Trax) were used to estimate the flux of NO from the dairy during August 2011 with the assumption that emissions were primarily from animal feed. NO emissions from silage were also directly measured from feed to provide additional insight into the sources. Isolation flux chamber measurements imply an NO flux from the feed of about 1.3 × 10-3 g m-2 h-1, but these relatively low fluxes are inconsistent with the elevated NO concentrations observed during August 2011. This implies that either the flux chamber method grossly underestimates the true NO emissions from feed, or that most of the ambient NO measured at the dairy is from other sources. Emissions from farm machinery may account for the NO concentrations observed. Animal feed thus appears to be a small contributor to NOx emissions within Central California.

Aqueous-Phase Mechanism for Secondary Organic Aerosol Formation from Isoprene: Application to the Southeast United States and Co-Benefit of SO2 Emission Controls

NASA Technical Reports Server (NTRS)

Marais, E. A.; Jacob, D. J.; Jimenez, J. L.; Campuzano-Jost, P.; Day, D. A.; Hu, W.; Krechmer, J.; Zhu, L.; Kim, P. S.; Miller, C. C.;

Atmospheric pollution reduction effect and regional predicament: An empirical analysis based on the Chinese provincial NOx emissions.

PubMed

Ding, Lei; Liu, Chao; Chen, Kunlun; Huang, Yalin; Diao, Beidi

2017-07-01

Atmospheric pollution emissions have become a matter of public concern in recent years. However, most of the existing researches on NOx pollution are from the natural science and technology perspective, few studies have been conducted from an economic point, and regional differences have not been given adequate attention. This paper adopts provincial panel data from 2006 to 2013 and the LMDI model to analyze the key driving factors and regional dilemmas of NOx emissions. The results show that significant regional disparities still exit on NO x emissions and its reduction effect 27 provinces didn't accomplish their corresponding reduction targets. Economic development factor is the dominating driving factor of NO x emissions during the study period, while energy efficiency and technology improvement factors offset total NO x emissions in the majority of provinces. In addition, the industrial structure factor plays a more significant role in reducing the NO x emissions after 2011. Therefore, the government should consider all these factors as well as regional heterogeneity in developing appropriate pollution mitigating policies. It's necessary to change NOx emissions control attitude from original key areas control to divided-zone control, not only attaches great importance to the reduction of the original key areas, but also emphasizes the new potential hotspots with high NO x emissions. Copyright © 2017 Elsevier Ltd. All rights reserved.

Small Engine Technology (SET) - Task 4, Regional Turboprop/Turbofan Engine Advanced Combustor Study

NASA Technical Reports Server (NTRS)

Reynolds, Robert; Srinivasan, Ram; Myers, Geoffrey; Cardenas, Manuel; Penko, Paul F. (Technical Monitor)

2003-01-01

Under the SET Program Task 4 - Regional Turboprop/Turbofan Engine Advanced Combustor Study, a total of ten low-emissions combustion system concepts were evaluated analytically for three different gas turbine engine geometries and three different levels of oxides of nitrogen (NOx) reduction technology, using an existing AlliedSignal three-dimensional (3-D) Computational Fluid Dynamics (CFD) code to predict Landing and Takeoff (LTO) engine cycle emission values. A list of potential Barrier Technologies to the successful implementation of these low-NOx combustor designs was created and assessed. A trade study was performed that ranked each of the ten study configurations on the basis of a number of manufacturing and durability factors, in addition to emissions levels. The results of the trade study identified three basic NOx-emissions reduction concepts that could be incorporated in proposed follow-on combustor technology development programs aimed at demonstrating low-NOx combustor hardware. These concepts are: high-flow swirlers and primary orifices, fuel-preparation cans, and double-dome swirlers.

Improved NOx emissions and combustion characteristics for a retrofitted down-fired 300-MWe utility boiler.

PubMed

Li, Zhengqi; Ren, Feng; Chen, Zhichao; Liu, Guangkui; Xu, Zhenxing

2010-05-15

A new technique combining high boiler efficiency and low-NO(x) emissions was employed in a 300MWe down-fired boiler as an economical means to reduce NO(x) emissions in down-fired boilers burning low-volatile coals. Experiments were conducted on this boiler after the retrofit with measurements taken of gas temperature distributions along the primary air and coal mixture flows and in the furnace, furnace temperatures along the main axis and gas concentrations such as O(2), CO and NO(x) in the near-wall region. Data were compared with those obtained before the retrofit and verified that by applying the combined technique, gas temperature distributions in the furnace become more reasonable. Peak temperatures were lowered from the upper furnace to the lower furnace and flame stability was improved. Despite burning low-volatile coals, NO(x) emissions can be lowered by as much as 50% without increasing the levels of unburnt carbon in fly ash and reducing boiler thermal efficiency.