The Ship Movement Trajectory Prediction Algorithm Using Navigational Data Fusion

PubMed Central

Borkowski, Piotr

2017-01-01

It is essential for the marine navigator conducting maneuvers of his ship at sea to know future positions of himself and target ships in a specific time span to effectively solve collision situations. This article presents an algorithm of ship movement trajectory prediction, which, through data fusion, takes into account measurements of the ship’s current position from a number of doubled autonomous devices. This increases the reliability and accuracy of prediction. The algorithm has been implemented in NAVDEC, a navigation decision support system and practically used on board ships. PMID:28632176

Gastrointestinal illness on passenger cruise ships, 1975-1978.

PubMed Central

Dannenberg, A L; Yashuk, J C; Feldman, R A

1982-01-01

Following investigations in 1972-1973 of outbreaks of enteric disease on cruise ships using American ports, a surveillance system was established which required that 24 hours before arrival in port, each ship report the number of persons with diarrheal illness seen by the ship's physician during the cruise. The reported data were found to be reliable; they established a baseline incidence for diarrhea on cruise ships. A significantly high portion of enteric disease outbreaks occurred on vessels that did not pass routine annual or semiannual sanitation inspections. The cruise ship sanitation program, developed with the cooperation of the cruise ship industry and the Centers for Disease Control, appears to have been successful in reducing the overall rate of cruise ship associated outbreaks of enteric illness. PMID:7065338

Prediction of induced vibrations for a passenger - car ferry

NASA Astrophysics Data System (ADS)

Crudu, L.; Neculet, O.; Marcu, O.

2016-08-01

In order to evaluate the ship hull global vibrations, propeller excitation must be properly considered being mandatory to know enough accurate the magnitude of the induced hull pressure impulses. During the preliminary design stages, the pressures induced on the aft part of the ship by the operating propeller can be evaluated based on the guidelines given by the international standards or by the provisions of the Classification Societies. These approximate formulas are taking into account the wake field which, unfortunately, can be only estimated unless experimental towing tank tests are carried out. Another possibility is the numerical evaluation with different Computational Fluid Dynamics (CFD) codes. However, CFD methods are not always easy to be used requiring an accurate description of the hull forms in the aft part of the ship. The present research underlines these aspects during the preliminary prediction of propeller induced vibrations for a double-ended passenger-car ferry propelled by two azimuth fixed pitch thrusters placed at both ends of the ship. The evaluation of the global forced vibration is performed considering the 3D global Finite Element (FE) model, with NX Nastran for Windows. Based on the presented results, the paper provides reliable information to be used during the preliminary design stages.

Real-Time Telemetry System for Monitoring Motion of Ships Based on Inertial Sensors

PubMed Central

Núñez, José M.; Araújo, Marta G.; García-Tuñón, I.

2017-01-01

A telemetry system for real-time monitoring of the motions, position, speed and course of a ship at sea is presented in this work. The system, conceived as a subsystem of a radar cross-section measurement unit, could also be used in other applications as ships dynamics characterization, on-board cranes, antenna stabilizers, etc. This system was designed to be stand-alone, reliable, easy to deploy, low-cost and free of requirements related to stabilization procedures. In order to achieve such a unique combination of functionalities, we have developed a telemetry system based on redundant inertial and magnetic sensors and GPS (Global Positioning System) measurements. It provides a proper data storage and also has real-time radio data transmission capabilities to an on-shore station. The output of the system can be used either for on-line or off-line processing. Additionally, the system uses dual technologies and COTS (Commercial Off-The-Shelf) components. Motion-positioning measurements and radio data link tests were successfully carried out in several ships of the Spanish Navy, proving the compliance with the design targets and validating our telemetry system. PMID:28441330

Field test of available methods to measure remotely SOx and NOx emissions from ships

NASA Astrophysics Data System (ADS)

Balzani Lööv, J. M.; Alfoldy, B.; Gast, L. F. L.; Hjorth, J.; Lagler, F.; Mellqvist, J.; Beecken, J.; Berg, N.; Duyzer, J.; Westrate, H.; Swart, D. P. J.; Berkhout, A. J. C.; Jalkanen, J.-P.; Prata, A. J.; van der Hoff, G. R.; Borowiak, A.

2014-08-01

Methods for the determination of ship fuel sulphur content and NOx emission factors based on remote measurements have been compared in the harbour of Rotterdam and compared to direct stack emission measurements on the ferry Stena Hollandica. The methods were selected based on a review of the available literature on ship emission measurements. They were either optical (LIDAR, Differential Optical Absorption Spectroscopy (DOAS), UV camera), combined with model-based estimates of fuel consumption, or based on the so called "sniffer" principle, where SO2 or NOx emission factors are determined from simultaneous measurement of the increase of CO2 and SO2 or NOx concentrations in the plume of the ship compared to the background. The measurements were performed from stations at land, from a boat and from a helicopter. Mobile measurement platforms were found to have important advantages compared to the land-based ones because they allow optimizing the sampling conditions and sampling from ships on the open sea. Although optical methods can provide reliable results it was found that at the state of the art level, the "sniffer" approach is the most convenient technique for determining both SO2 and NOx emission factors remotely. The average random error on the determination of SO2 emission factors comparing two identical instrumental set-ups was 6%. However, it was found that apparently minor differences in the instrumental characteristics, such as response time, could cause significant differences between the emission factors determined. Direct stack measurements showed that about 14% of the fuel sulphur content was not emitted as SO2. This was supported by the remote measurements and is in agreement with the results of other field studies.

46 CFR 62.30-1 - Failsafe.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false Failsafe. 62.30-1 Section 62.30-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING VITAL SYSTEM AUTOMATION Reliability and Safety... control, safety control, and alarm systems must be failsafe. ...

46 CFR 62.30-1 - Failsafe.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false Failsafe. 62.30-1 Section 62.30-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING VITAL SYSTEM AUTOMATION Reliability and Safety... control, safety control, and alarm systems must be failsafe. ...

46 CFR 62.30-1 - Failsafe.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false Failsafe. 62.30-1 Section 62.30-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING VITAL SYSTEM AUTOMATION Reliability and Safety... control, safety control, and alarm systems must be failsafe. ...

In-harbor and at-sea electromagnetic compatibility survey for maritime satellite L-band shipboard terminal

NASA Technical Reports Server (NTRS)

1974-01-01

Geostationary maritime satellites, one over the Pacific and one over the Atlantic Ocean, are planned to make available high-speed communications and navigation (position determination) services to ships at sea. A shipboard satellite terminal, operating within the authorized maritime L-band, 1636.5 to 1645.0 MHz, will allow ships to pass voice, teletype, facsimile, and data messages to shore communication facilities with a high degree of reliability. The shore-to-ship link will also operate in the maritime L-band from 1535.0 to 1543.5 MHz. A significant number or maritime/commercial ships are expected to be equipped with an L-band satellite terminal by the year 1980, and so consequently, there is an interest in determining electromagnetic compatibility between the proposed L-band shipboard terminal and existing, on-board, shipboard communications/electronics and electrical systems, as well as determining the influence of shore-based interference sources. The shipboard electromagnetic interference survey described was conducted on-board the United States Line's American Leader class (15,690 tons) commercial container ship, the "American Alliance" from June 16 to 20, 1974. Details of the test plan and measurements are given.

Distributed Ship Navigation Control System Based on Dual Network

NASA Astrophysics Data System (ADS)

Yao, Ying; Lv, Wu

2017-10-01

Navigation system is very important for ship’s normal running. There are a lot of devices and sensors in the navigation system to guarantee ship’s regular work. In the past, these devices and sensors were usually connected via CAN bus for high performance and reliability. However, as the development of related devices and sensors, the navigation system also needs the ability of high information throughput and remote data sharing. To meet these new requirements, we propose the communication method based on dual network which contains CAN bus and industrial Ethernet. Also, we import multiple distributed control terminals with cooperative strategy based on the idea of synchronizing the status by multicasting UDP message contained operation timestamp to make the system more efficient and reliable.

Studies on nano-additive for the substitution of hazardous chemical substances in antifouling coatings for the protection of ship hulls.

PubMed

Zhao, Xiaodong; Fan, Weijie; Duan, Jizhou; Hou, Baorong

2014-07-01

Adhesion and growth of biofouling organisms have severe influence on the reliability, service life and environmental adaptability of marine ships. Based on the bactericidal capacity of cuprous oxide and photochemical effect of nano-additive, environment-friendly and efficient marine antifouling paints were prepared in this study. The evaluation of the antifouling paints was carried out by the laboratory method using bacteria and phytoplanktonic microorganisms as target organisms, as well as measurements with panels in shallow submergence in natural seawater. Results showed good agreement of all the tests, indicating the remarkable antifouling performance of the paints. To our knowledge, this was one of the first systematic studies on effects of nano-additive for the substitution of hazardous chemical substances in antifouling coatings for the protection of ship hulls by measurements on bacterial inhibition, algal adhesion and growth of large organisms.

46 CFR 169.621 - Communications.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 7 2012-10-01 2012-10-01 false Communications. 169.621 Section 169.621 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS SAILING SCHOOL VESSELS Machinery and Electrical Steering Systems § 169.621 Communications. A reliable means of voice communications must be...

46 CFR 169.621 - Communications.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 7 2014-10-01 2014-10-01 false Communications. 169.621 Section 169.621 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS SAILING SCHOOL VESSELS Machinery and Electrical Steering Systems § 169.621 Communications. A reliable means of voice communications must be...

46 CFR 169.621 - Communications.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 7 2011-10-01 2011-10-01 false Communications. 169.621 Section 169.621 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS SAILING SCHOOL VESSELS Machinery and Electrical Steering Systems § 169.621 Communications. A reliable means of voice communications must be...

46 CFR 169.621 - Communications.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Communications. 169.621 Section 169.621 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS SAILING SCHOOL VESSELS Machinery and Electrical Steering Systems § 169.621 Communications. A reliable means of voice communications must be...

46 CFR 62.30-10 - Testing.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false Testing. 62.30-10 Section 62.30-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING VITAL SYSTEM AUTOMATION Reliability and Safety... override safety trip control systems. This equipment must indicate when it is active. ...

46 CFR 62.30-10 - Testing.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false Testing. 62.30-10 Section 62.30-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING VITAL SYSTEM AUTOMATION Reliability and Safety... override safety trip control systems. This equipment must indicate when it is active. ...

46 CFR 62.30-10 - Testing.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false Testing. 62.30-10 Section 62.30-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING VITAL SYSTEM AUTOMATION Reliability and Safety... override safety trip control systems. This equipment must indicate when it is active. ...

46 CFR 62.30-10 - Testing.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false Testing. 62.30-10 Section 62.30-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING VITAL SYSTEM AUTOMATION Reliability and Safety... override safety trip control systems. This equipment must indicate when it is active. ...

[The Study of Health in Pomerania (SHIP) reference values for cardiopulmonary exercise testing].

PubMed

Gläser, S; Ittermann, T; Schäper, C; Obst, A; Dörr, M; Spielhagen, T; Felix, S B; Völzke, H; Bollmann, T; Opitz, C F; Warnke, C; Koch, B; Ewert, R

2013-01-01

The interpretation of gas exchange measured by cardiopulmonary exercise testing (CPET) depends on reliable reference values. Within the population based Study of Health in Pomerania (SHIP) CPET was assessed in 1706 volunteers. The assessment based on symptom limited exercise tests on a bicycle in a sitting position according to a modified Jones protocol. CPET was embedded in an extensive examination program. After the exclusion of active smokers and volunteers with evidence of cardiopulmonary and musculoskeletal disorders the reference population comprised 616 healthy subjects (333 women) aged 25 to 85 years. Reference equations including upper and/or lower limits based on quantile regression were assessed. All values were corrected for the most important influencing factors.This study provides reference equations for gas exchange and exercise capacity assessed within a population in Germany. © Georg Thieme Verlag KG Stuttgart · New York.

46 CFR 62.30-1 - Failsafe.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Failsafe. 62.30-1 Section 62.30-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING VITAL SYSTEM AUTOMATION Reliability and Safety Criteria, All Automated Vital Systems § 62.30-1 Failsafe. (a) The failsafe state must be evaluated for each...

46 CFR 62.01-3 - Scope.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Scope. 62.01-3 Section 62.01-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING VITAL SYSTEM AUTOMATION General Provisions... automation; (2) In subpart 62.30, the criteria used to evaluate the designed reliability and safety of all...

Field test of available methods to measure remotely SO2 and NOx emissions from ships

NASA Astrophysics Data System (ADS)

Balzani Lööv, J. M.; Alfoldy, B.; Beecken, J.; Berg, N.; Berkhout, A. J. C.; Duyzer, J.; Gast, L. F. L.; Hjorth, J.; Jalkanen, J.-P.; Lagler, F.; Mellqvist, J.; Prata, F.; van der Hoff, G. R.; Westrate, H.; Swart, D. P. J.; Borowiak, A.

2013-11-01

Methods for the determination of ship fuel sulphur content and NOx emission factors from remote measurements have been compared in the harbour of Rotterdam and compared to direct stack emission measurements on the ferry Stena Hollandica. The methods were selected based on a review of the available literature on ship emission measurements. They were either optical (LIDAR, DOAS, UV camera), combined with model based estimates of fuel consumption, or based on the so called "sniffer" principle, where SO2 or NOx emission factors are determined from simultaneous measurement of the increase of CO2 and SO2 or NOx concentrations in the plume of the ship compared to the background. The measurements were performed from stations at land, from a boat, and from a helicopter. Mobile measurement platforms were found to have important advantages compared to the landbased ones because they allow to optimize the sampling conditions and to sample from ships on the open sea. Although optical methods can provide reliable results, it was found that at the state of the art, the "sniffer" approach is the most convenient technique for determining both SO2 and NOx emission factors remotely. The average random error on the determination of SO2 emission factors comparing two identical instrumental set-ups was 6%. However, it was found that apparently minor differences in the instrumental characteristics, such as response time, could cause significant differences between the emission factors determined. Direct stack measurements showed that about 14% of the fuel sulphur content was not emitted as SO2. This was supported by the remote measurements and is in agreement with the results of other field studies.

Study on Collision of Ship Side Structure by Simplified Plastic Analysis Method

NASA Astrophysics Data System (ADS)

Sun, C. J.; Zhou, J. H.; Wu, W.

2017-10-01

During its lifetime, a ship may encounter collision or grounding and sustain permanent damage after these types of accidents. Crashworthiness has been based on two kinds of main methods: simplified plastic analysis and numerical simulation. A simplified plastic analysis method is presented in this paper. Numerical methods using the non-linear finite-element software LS-DYNA are conducted to validate the method. The results show that, as for the accuracy of calculation results, the simplified plasticity analysis are in good agreement with the finite element simulation, which reveals that the simplified plasticity analysis method can quickly and accurately estimate the crashworthiness of the side structure during the collision process and can be used as a reliable risk assessment method.

46 CFR 62.15-1 - Conditions under which equivalents may be used.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false Conditions under which equivalents may be used. 62.15-1 Section 62.15-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING VITAL... level of safety and reliability. Demonstration of functional equivalence must include comparison of a...

46 CFR 62.15-1 - Conditions under which equivalents may be used.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false Conditions under which equivalents may be used. 62.15-1 Section 62.15-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING VITAL... level of safety and reliability. Demonstration of functional equivalence must include comparison of a...

46 CFR 62.15-1 - Conditions under which equivalents may be used.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false Conditions under which equivalents may be used. 62.15-1 Section 62.15-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING VITAL... level of safety and reliability. Demonstration of functional equivalence must include comparison of a...

46 CFR 62.15-1 - Conditions under which equivalents may be used.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false Conditions under which equivalents may be used. 62.15-1 Section 62.15-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING VITAL... level of safety and reliability. Demonstration of functional equivalence must include comparison of a...

46 CFR 62.30-10 - Testing.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Testing. 62.30-10 Section 62.30-10 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING VITAL SYSTEM AUTOMATION Reliability and Safety... accordance with subpart 61.40 of this chapter. (b) On-line built-in test equipment must not lock out or...

Managing the financial risk of low water levels in Great Lakes with index-based contracts

NASA Astrophysics Data System (ADS)

Meyer, E.; Characklis, G. W.; Brown, C. M.; Moody, P.

2014-12-01

Low water levels in the Great Lakes have recently had significant financial impacts on the region's commercial shipping, responsible for transporting millions of dollars' worth of bulk goods each year. Low lake levels can significantly affect shipping firms, as cargo capacity is a function of draft, or the distance between water level and the ship's bottom. Draft increases with weight, and lower lake levels force ships to reduce cargo to prevent running aground in shallow harbors, directly impacting the finances of shipping companies. Risk transfer instruments may provide adaptable, yet unexplored, alternatives for managing these financial risks, at significantly less expense than more traditional solutions (e.g., dredging). Index-based financial instruments can be particularly attractive as contract payouts are directly linked to well-defined transparent metrics (e.g., lake levels), eliminating the need for subjective adjustors, as well as concerns over moral hazard. In developing such instruments, a major challenge is identifying an index that is well correlated with financial losses, and thus a contract that reliably pays out when losses are experienced (low basis risk). In this work, a relationship between lake levels and shipping revenues is developed, and actuarial analyses of the frequency and magnitude of revenue losses is completed using this relationship and synthetic water level data. This analysis is used to develop several types of index-based contracts. A standardized suite of binary contracts is developed, with each indexed to lake levels and priced according to predefined thresholds. These are combined to form portfolios with different objectives (e.g. options, collars), with optimal portfolio structure and length of coverage determined by limiting basis risk and contract cost, using simulations over the historic dataset. Results suggest that portfolios of these binary contracts can substantially reduce the risk of financial losses during periods of low lake level at a cost of only 1-3% of total revenues.

HSI top-down requirements analysis for ship manpower reduction

NASA Astrophysics Data System (ADS)

Malone, Thomas B.; Bost, J. R.

2000-11-01

U.S. Navy ship acquisition programs such as DD 21 and CVNX are increasingly relying on top down requirements analysis (TDRA) to define and assess design approaches for workload and manpower reduction, and for ensuring required levels of human performance, reliability, safety, and quality of life at sea. The human systems integration (HSI) approach to TDRA begins with a function analysis which identifies the functions derived from the requirements in the Operational Requirements Document (ORD). The function analysis serves as the function baseline for the ship, and also supports the definition of RDT&E and Total Ownership Cost requirements. A mission analysis is then conducted to identify mission scenarios, again based on requirements in the ORD, and the Design Reference Mission (DRM). This is followed by a mission/function analysis which establishes the function requirements to successfully perform the ship's missions. Function requirements of major importance for HSI are information, performance, decision, and support requirements associated with each function. An allocation of functions defines the roles of humans and automation in performing the functions associated with a mission. Alternate design concepts, based on function allocation strategies, are then described, and task networks associated with the concepts are developed. Task network simulations are conducted to assess workloads and human performance capabilities associated with alternate concepts. An assessment of the affordability and risk associated with alternate concepts is performed, and manning estimates are developed for feasible design concepts.

Major safety provisions in nuclear-powered ships

DOE Office of Scientific and Technical Information (OSTI.GOV)

Khlopkin, N.S.; Belyaev, V.M.; Dubrovin, A.M.

1984-12-01

Considerable experience has been accumulated in the Soviet Union on the design, construction and operation of nuclear-powered civilian ships: the icebreakers Lenin, Leonid Brezhnev and Sibir. The nuclear steam plants (NSP) used on these as the main energy source have been found to be highly reliable and safe, and it is desirable to use them in the future not only in icebreakers but also in transport ships for use in ice fields. The Soviet program for building and developing nuclear-powered ships has involved careful attention to safety in ships containing NSP. The experience with the design and operation of nuclearmore » icebreakers in recent years has led to the revision of safety standards for the nuclear ships and correspondingly ship NSP and international guidelines have been developed. If one meets the requirements as set forth in these documents, one has a safe basis for future Soviet nuclear-powered ships. The primary safety provisions for NSP are presented in this paper.« less

Examples of, reasons for, and consequences of the poor quality of wind data from ships for the marine boundary layer: Implications for remote sensing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pierson, W.J. Jr.

1990-08-15

Wind reports by data buoys are used to demonstrate that these reports have in the past provided useful values for the synoptic scale winds and that at present these reports provide very reliable values for the synoptic scale winds. Past studies of wind reports by ships have revealed that the data are of poor quality, but the causes for this poor quality are not identified. Examples of the poor quality of wind data from ships are obtained by comparing ship reports with buoy reports and comparing reports of different kinds of ships with each other. These comparisons identify many differentmore » reasons for the poor quality of wind data from ships. Suggestions are made for improving the quality of ship data. The consequences of the poor quality of ship winds are described in terms of the effects on weather and wave forecasts. The implications for remotely sensed winds are discussed.« less

Basic aspects and contributions to the optimization of energy systems exploitation of a super tanker ship

NASA Astrophysics Data System (ADS)

Faitar, C.; Novac, I.

2017-08-01

Today, the concept of energy efficiency or energy optimization in ships has become one of the main problems of engineers in the whole world. To increase the fiability of a crude oil super tanker ship it means, among other things, to improve the energy performance and optimize the fuel consumption of ship through the development of engines and propulsion system or using alternative energies. Also, the importance of having an effective and reliable Power Management System (PMS) in a vessel operating system means to reduce operational costs and maintain power system of machine parts working in minimum stress in all operating conditions. Studying the Energy Efficiency Design Index and Energy Efficiency Operational Indicator for a crude oil super tanker ship, it allows us to study the reconfiguration of ship power system introducing new generation systems.

Fusion of navigational data in River Information Services

NASA Astrophysics Data System (ADS)

Kazimierski, W.

2009-04-01

River Information Services (RIS) is the complex system of solutions and services for inland shipping. It has been the scope of works carried out in most of European countries for last several years. There were also a few major pan-European projects like INDRIS or COMPRIS launched for these purposes. The main idea of RIS is to harmonize the activities of various companies, authorities and other users of inland waterways in Europe. In the last time growing activity in this area in Poland can be also noticed. The leading example can be the works carried out in Chair of Geoinformatics in Maritime University of Szczecin regarding RIS for the needs of Odra River. The Directive 2005/44/EC of European Parliament and Europe Council, followed by European Commission regulations, give precise guidelines on implementing RIS in Europe, stating the services that should be provided. Among them Traffic Information and Traffic Management services can be found. As per guidelines they should be based on tracking and tracing of ships in the inland waters. The results of tracking and tracing are Tactical Traffic Image and Strategic Traffic Image. The guidelines stated that, tracking and tracing system in RIS shall consist of various type sensors. The most important of them is thought to be Automatic Information System (AIS), and particularly its river version - Inland AIS. It is based on determining the position of ships by satellite positioning systems (mainly DGPS) and transmitting it to other users on radio VHF frequences. This guarantees usually high accuracy of data related to movement of ships (assuming proper functioning of system and ship's sensors), and gives the possibility of transmitting additional information about ship, like dimensions, port of destination, cargo, etc. However the other sensors that can be used for tracking shall not be forgotten. The most important of them are radar (traditionally used for tracking purposes in Vessel Traffic Systems) and video camera. Their main advantage over AIS is total independence from tracked target's facilities. For example, wrong indications of ship's GPS would affect AIS accuracy, but wouldn't have any impact on values estimated by radar. In addition to this in many times update rate for AIS data is longer than for radar. Thus, it can be noticed, that efficient tracking system introduced in RIS shall use both AIS receivers (based on satellite derived positions), and independent radar and camera sensors. This will however cause determining at least two different set of information about positions and movement parameters of targets. Doubled or multiplied vectors for single target are unacceptable, due to safety of navigation and traffic management. Hence the need of data fusion in RIS is obvious. The main goal is to develop unambiguous, clear and reliable information about ships' position and movement for all users in the system. Data fusion itself is not a new problem in maritime navigation. There are systems of Integrated Bridge on sea-going ships, which use information coming out from different sources. However the possibilities of integration of navigational information in the aspect of inland navigation, especially in River Information Services, still needs to be thoroughly surveyed. It is quite useful for simplifying the deduction, to introduce two data fusion levels. First of them is being done on board of the vessel. Its aim is to integrate all information coming from different sensors in the so called Integrated Navigational System. The other task of this fusion is to estimate reliable information about other objects based on AIS and radar. The second level is the integration of AIS, radar and closed-circuit television (CCTV) carried out in coastal station in order to determine Tactical and Strategic Traffic Image. The navigational information in RIS itself can be divided into two main groups. The first one is called static data and contains al basic information related to ship itself and the voyage, like dimensions, destination, etc. The second group is called dynamic data and contains all the information, which variability is important for creating Tactical Traffic Image. Both groups require different fusion algorithms, which take into consideration sources, update rate and method, accuracy and reliability. The article contains different issues related to navigational information fusion in River Information Services. It includes short description of structures and sources of navigational information and also the most popular integration methods. More detailed analysis was made for fusion of position derived from satellite systems (GPS) and from radar. The concept of tracking system, combining Inland AIS, radar and CCTV for the needs of RIS is introduced.

Non-Reporting Ship Traffic in the Western Indian Ocean

NASA Astrophysics Data System (ADS)

Greidanus, Harm; Santamaria, Carlos; Alvarez, Marlene; Krause, Detmar; Stasolla, Mattia; Vachon, Paris W.

2016-08-01

AIS ship position reporting data from up to 17 satellites and several coastal locations covering the Western Indian Ocean were collected during a period of one year, that ended 15 Sep 2015. In addition, 1,361 satellite SAR images that were acquired over the region in the same timeframe, were analysed for ship detection. The major part of these were Sentinel-1 images that were analysed fully automatically, yielding 11,510 ship detections that were deemed reliable. Correlating these detections with the reporting ship traffic indicates that, overall, fully one-third of the ships detected with satellite SAR are not reporting on AIS. Some of the analysed SAR data was subjected to manual verification. This concerned data from TerraSAR-X, RADARSAT-2, COSMO-SkyMed, and ALOS-2- PALSAR of various image modes, plus some of the Sentinel-1 images. This confirmed the quoted average for the fraction of non-reporting ships. However, within the overall average there are large geographical variations, besides variations with image resolution.

Marine Technician's Handbook, Instructions for Taking Air Samples on Board Ship: Carbon Dioxide Project.

ERIC Educational Resources Information Center

Keeling, Charles D.

This booklet is one of a series intended to provide explicit instructions for the collection of oceanographic data and samples at sea. The methods and procedures described have been used by the Scripps Institution of Oceanography and found reliable and up-to-date. Instructions are given for taking air samples on board ship to determine the…

Modeling of liquid flow in surface discontinuities

NASA Astrophysics Data System (ADS)

Lobanova, I. S.; Meshcheryakov, V. A.; Kalinichenko, A. N.

2018-01-01

Polymer composite and metallic materials have found wide application in various industries such as aviation, rocket, car manufacturing, ship manufacturing, etc. Many design elements need permanent quality control. Ensuring high quality and reliability of products is impossible without effective nondestructive testing methods. One of these methods is penetrant testing using penetrating substances based on liquid penetration into defect cavities. In this paper, we propose a model of liquid flow to determine the rates of filling the defect cavities with various materials and, based on this, to choose optimal control modes.

Sustainability Logistics Basing - Science and Technology Objective - Demonstration; Demonstration #1 - 50 Person Camp Demo

DTIC Science & Technology

2017-08-17

sources: solar panels, two wind turbines , JP8/diesel genset, and alternating current (AC) shore power. The system can be towed by a High Mobility...energy. The project office shipped two REDUCE units to the demonstration, one with wind turbines and one without. For the demonstration, the team...operated and collected data from the system without wind turbines due to the greater reliability of its integrated genset. The system with wind

Reliability-Based Performance Assessment of Damaged Ships

DTIC Science & Technology

2006-10-01

37OR.A 2 AceI 2 oce 3 3C7R Main Deck Plan View at 9.906 metre STAA T~SIc ACCa IC 111 tI RO MAO ’ 2 0004 M 3O m 3 STORES) me 3 1 002~s STOR1 PfIS PlnVIS...Vol. 15, pp.7 4 -9 3 . Kaplan , M. Benatar, M., Bentson, J., Achtarides, T.A. (1984). "Analysis and assessment of major uncertainties associated with

Food commodity pipeline management in transitional settings: challenges and lessons learned from the first USAID food development program in South Sudan

PubMed Central

Tappis, Hannah; Doocy, Shannon; Amoako, Stephen

2013-01-01

ABSTRACT Despite decades of support for international food assistance programs by the U.S. Agency for International Development (USAID) Office of Food for Peace, relatively little is known about the commodity pipeline and management issues these programs face in post-conflict and politically volatile settings. Based on an audit of the program's commodity tracking system and interviews with 13 key program staff, this case study documents the experiences of organizations implementing the first USAID-funded non-emergency (development) food assistance program approved for Sudan and South Sudan. Key challenges and lessons learned in this experience about food commodity procurement, transport, and management may help improve the design and implementation of future development food assistance programs in a variety of complex, food-insecure settings around the world. Specifically, expanding shipping routes in complex political situations may facilitate reliable and timely commodity delivery. In addition, greater flexibility to procure commodities locally, rather than shipping U.S.-procured commodities, may avoid unnecessary shipping delays and reduce costs. PMID:25276532

Free-space, laser-based data transmission: satellite communication as a technology driver for the development of fast, reliable terrestrial data networks

NASA Astrophysics Data System (ADS)

Gerken, Martin; Luichtel, Georg

2008-04-01

High-resolution digital images with high refresh rates cause an enormous amount of data that must be forwarded from the source to the recipient. This is where wireless transmission as an RF technology quickly reaches its limits. With its high bandwidth, laser-based data transmission avoids this problem. An added benefit is a higher level of security against eavesdropping that can be further increased through the use of quantum optical encryption techniques. For military applications, several scenarios will be considered. Especially for the navy, communication between a ship and land for remote forces using free space air at the eye-safe laser wavelength of 1550 nm is necessary. Data transfer at this wavelength between ships is also important for an exchange of tactical images of the local situation. In the future, the direct communication between a ship and a submarine through water will be required. Bug-proof and broad bandwidth transmission of reconnaissance data will be necessary over distances of approx. several 100 m at the laser wavelength of 532 nm. This paper will show how experiences gained through the development of optical data links from satellites to ground stations can be used as an enabling technology for additional applications for the development of stable data connections under atmospheric conditions.

Fault tree analysis of fire and explosion accidents for dual fuel (diesel/natural gas) ship engine rooms

NASA Astrophysics Data System (ADS)

Guan, Yifeng; Zhao, Jie; Shi, Tengfei; Zhu, Peipei

2016-09-01

In recent years, China's increased interest in environmental protection has led to a promotion of energy-efficient dual fuel (diesel/natural gas) ships in Chinese inland rivers. A natural gas as ship fuel may pose dangers of fire and explosion if a gas leak occurs. If explosions or fires occur in the engine rooms of a ship, heavy damage and losses will be incurred. In this paper, a fault tree model is presented that considers both fires and explosions in a dual fuel ship; in this model, dual fuel engine rooms are the top events. All the basic events along with the minimum cut sets are obtained through the analysis. The primary factors that affect accidents involving fires and explosions are determined by calculating the degree of structure importance of the basic events. According to these results, corresponding measures are proposed to ensure and improve the safety and reliability of Chinese inland dual fuel ships.

Numerical simulation of the wave-induced non-linear bending moment of ships

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xia, J.; Wang, Z.; Gu, X.

1995-12-31

Ships traveling in moderate or rough seas may experience non-linear bending moments due to flare effect and slamming loads. The numerical simulation of the total wave-induced bending moment contributed from both the wave frequency component induced by wave forces and the high frequency whipping component induced by slamming actions is very important in predicting the responses and ensuring the safety of the ship in rough seas. The time simulation is also useful for the reliability analysis of ship girder strength. The present paper discusses four different methods of the numerical simulation of wave-induced non-linear vertical bending moment of ships recentlymore » developed in CSSRC, including the hydroelastic integral-differential method (HID), the hydroelastic differential analysis method (HDA), the combined seakeeping and structural forced vibration method (CSFV), and the modified CSFV method (MCSFV). Numerical predictions are compared with the experimental results obtained from the elastic ship model test of S-175 container ship in regular and irregular waves presented by Watanabe Ueno and Sawada (1989).« less

Control and Optimization of Electric Ship Propulsion Systems with Hybrid Energy Storage

NASA Astrophysics Data System (ADS)

Hou, Jun

Electric ships experience large propulsion-load fluctuations on their drive shaft due to encountered waves and the rotational motion of the propeller, affecting the reliability of the shipboard power network and causing wear and tear. This dissertation explores new solutions to address these fluctuations by integrating a hybrid energy storage system (HESS) and developing energy management strategies (EMS). Advanced electric propulsion drive concepts are developed to improve energy efficiency, performance and system reliability by integrating HESS, developing advanced control solutions and system integration strategies, and creating tools (including models and testbed) for design and optimization of hybrid electric drive systems. A ship dynamics model which captures the underlying physical behavior of the electric ship propulsion system is developed to support control development and system optimization. To evaluate the effectiveness of the proposed control approaches, a state-of-the-art testbed has been constructed which includes a system controller, Li-Ion battery and ultra-capacitor (UC) modules, a high-speed flywheel, electric motors with their power electronic drives, DC/DC converters, and rectifiers. The feasibility and effectiveness of HESS are investigated and analyzed. Two different HESS configurations, namely battery/UC (B/UC) and battery/flywheel (B/FW), are studied and analyzed to provide insights into the advantages and limitations of each configuration. Battery usage, loss analysis, and sensitivity to battery aging are also analyzed for each configuration. In order to enable real-time application and achieve desired performance, a model predictive control (MPC) approach is developed, where a state of charge (SOC) reference of flywheel for B/FW or UC for B/UC is used to address the limitations imposed by short predictive horizons, because the benefits of flywheel and UC working around high-efficiency range are ignored by short predictive horizons. Given the multi-frequency characteristics of load fluctuations, a filter-based control strategy is developed to illustrate the importance of the coordination within the HESS. Without proper control strategies, the HESS solution could be worse than a single energy storage system solution. The proposed HESS, when introduced into an existing shipboard electrical propulsion system, will interact with the power generation systems. A model-based analysis is performed to evaluate the interactions of the multiple power sources when a hybrid energy storage system is introduced. The study has revealed undesirable interactions when the controls are not coordinated properly, and leads to the conclusion that a proper EMS is needed. Knowledge of the propulsion-load torque is essential for the proposed system-level EMS, but this load torque is immeasurable in most marine applications. To address this issue, a model-based approach is developed so that load torque estimation and prediction can be incorporated into the MPC. In order to evaluate the effectiveness of the proposed approach, an input observer with linear prediction is developed as an alternative approach to obtain the load estimation and prediction. Comparative studies are performed to illustrate the importance of load torque estimation and prediction, and demonstrate the effectiveness of the proposed approach in terms of improved efficiency, enhanced reliability, and reduced wear and tear. Finally, the real-time MPC algorithm has been implemented on a physical testbed. Three different efforts have been made to enable real-time implementation: a specially tailored problem formulation, an efficient optimization algorithm and a multi-core hardware implementation. Compared to the filter-based strategy, the proposed real-time MPC achieves superior performance, in terms of the enhanced system reliability, improved HESS efficiency, and extended battery life.

USN shipboard infrared search and track (IRST) program

NASA Astrophysics Data System (ADS)

Misanin, Joseph E.

1997-08-01

On May 17, 1987 two EXOCET missiles hit and crippled the frigate USS STARK. Thirty seven sailors lost their lives due to the inability of the ship to defend itself against a sea- skimming cruise missile attack. In 1991, as a result of this incident, Congress mandated the establishment of a Program Executive Office for Ship Self Defense. The purpose of the legislation was to preclude another incident by placing a high priority on the combat system engineering process used to design and field the anti-ship cruise missile (ASCM) defense capability of surface ships. Over 35 countries now have sea- skimming ASCMs and this type of threat continues to proliferate. The use of IRST is a critical element of ship self defense, providing early and reliable detection of sea- skimming cruise missiles. This paper describes the contribution of IRST in providing self-defense and the current status of the United States Navy (USN) shipboard IRST development program.

Tether Deployer And Brake

NASA Technical Reports Server (NTRS)

Carroll, Joseph A.; Alexander, Charles M.

1993-01-01

Design concept promises speed, control, and reliability. Scheme for deploying tether provides for fast, free, and snagless payout and fast, dependable braking. Developed for small, expendable tethers in outer space, scheme also useful in laying transoceanic cables, deploying guidance wires to torpedoes and missiles, paying out rescue lines from ship to ship via rockets, deploying antenna wires, releasing communication and power cables to sonobuoys and expendable bathythermographs, and in reeling out lines from fishing rods.

Studying the Hurdles of Insulin Prescription (SHIP©): development, scoring and initial validation of a new self-administered questionnaire

PubMed Central

Martinez, Luc; Consoli, Silla M; Monnier, Louis; Simon, Dominique; Wong, Olivier; Yomtov, Bernard; Guéron, Béatrice; Benmedjahed, Khadra; Guillemin, Isabelle; Arnould, Benoit

2007-01-01

Background Although insulin therapy is well-accepted by symptomatic diabetic patients, it is still often delayed in less severe patients, in whom injectable insulin remains under-used. A better understanding of patients' perception of insulin would eventually help physicians to adopt the most appropriate dialogue when having to motivate patients to initiate or to intensify insulin injection. Methods The 'Studying the Hurdles of Insulin Prescription' (SHIP) questionnaire was developed based on a list of concepts derived from three diabetic patients' focus groups, and was included into two cross-sectional studies with similar design: SHIP Oral study and SHIP Premix study. Diabetic patients treated with oral hypoglycaemic agents (OHA; n = 1,494) and patients already treated with insulin (n = 1,150) completed the questionnaire at baseline, 6- and 12 months. Psychometric properties were assessed: 1) structure analysis by Principal Component Analysis (PCA) with Varimax rotation, 2) internal consistency reliability (Cronbach's alpha), and 3) concurrent validity (Spearman correlation coefficients with the Fear of Self-Injecting (FSI) score of the Diabetes Fear of Injecting and Self-testing Questionnaire. Reluctance/motivation towards insulin was assessed. Scores' ability to predict patients' insulin injection reluctance/motivation and initiation/intensification was evaluated with the Area Under the Receiver Operating Characteristic (ROC) Curve (AUC). Results PCA analysis confirmed the structure of the 14 items grouped into 3 dimensions: 'acceptance and motivation', 'fear and constraints', and 'restraints and barriers' towards insulin injection. Internal consistency reliability was excellent (Cronbach's alpha > 0.70); concurrent validity was good. The three scores were significantly predictive of patients' reluctance/motivation towards insulin injection initiation, as they were of patients' actual switch, except for the 'restraints and barriers' dimension. 'Acceptance and motivation' and 'fears and constraints' dimensions were also significantly predictive of patients' reluctance/motivation towards insulin intensification. By the end of the 12-month study, 179 of the initially OHA-treated patients had started insulin injections; 186 of the patients already treated with insulin had increased their injections. Conclusion The SHIP questionnaire provides reliable and valid assessment of diabetic patients' attitude towards insulin and injections. The predictive power of scores for patients' reluctance/motivation and actual treatment decisions demonstrates encouraging potential for further application in clinical practice. PMID:17727695

First validation of satellite microwave liquid water path with ship-based observations in marine low clouds

NASA Astrophysics Data System (ADS)

Painemal, D.; Cadeddu, M. P.; Greenwald, T. J.; Minnis, P.

2015-12-01

We present the first validation study of satellite microwave liquid water path, from four operational sensors, against in-situ observations from a ship-borne three-channel microwave radiometer collected over the northeast Pacific during May-August of 2013, along a ship transect length of 40˚ (33.7˚N, 118.2˚W - 21.3˚N, 157.8˚W). The satellite sensors analyzed here are: The Tropical Rainfall Measuring Mission (TRMM) Microwave Imager (TMI), Special Sensor Microwave Imager/Sounder (SSMIS) on the Defense Meteorological Satellite Program F16 and F17 satellites, and The Advanced Microwave Scanning Radiometer (AMSR-2) on board the Global Change Observation Mission - Water (GCOM-W1). Satellite retrievals show an overall correlation with hourly-averaged in-situ observations of 0.86 and a positive bias of 10.0 gm2, which decreases to 1.0 gm2 and a correlation that increases to 0.91 when selecting overcast scenes. The satellite bias for broken scenes remains below 22.2 gm2, although the removal of clear-sky in-situ samples yields an unbiased relationship. Satellites produce a diurnal cycle with amplitudes (35-47 gm2) consistent with ship-based observations. Longitudinal biases remain below 17.4 gm2, and they are negligible in overcast scenes and when clear-sky samples are removed from the in-situ hourly average. Our study indicates that satellite microwave retrievals are a reliable dataset for climate studies in marine warm low clouds. The implications for satellite visible/infrared retrievals will be also discussed.

A review of outbreaks of foodborne disease associated with passenger ships: evidence for risk management.

PubMed Central

Rooney, Roisin M.; Cramer, Elaine H.; Mantha, Stacey; Nichols, Gordon; Bartram, Jamie K.; Farber, Jeffrey M.; Benembarek, Peter K.

2004-01-01

OBJECTIVE: Foodborne disease outbreaks on ships are of concern because of their potentially serious health consequences for passengers and crew and high costs to the industry. The authors conducted a review of outbreaks of foodborne diseases associated with passenger ships in the framework of a World Health Organization project on setting guidelines for ship sanitation. METHODS: The authors reviewed data on 50 outbreaks of foodborne disease associated with passenger ships. For each outbreak, data on pathogens/toxins, type of ship, factors contributing to outbreaks, mortality and morbidity, and food vehicles were collected. RESULTS: The findings of this review show that the majority of reported outbreaks were associated with cruise ships and that almost 10,000 people were affected. Salmonella spp were most frequently associated with outbreaks. Foodborne outbreaks due to enterotoxigenic E. coli spp, Shigella spp, noroviruses (formally called Norwalk-like viruses), Vibrio spp, Staphylococcus aureus, Clostridium perfringens, Cyclospora sp, and Trichinella sp also occurred on ships. Factors associated with the outbreaks reviewed include inadequate temperature control, infected food handlers, contaminated raw ingredients, cross-contamination, inadequate heat treatment, and onshore excursions. Seafood was the most common food vehicle implicated in outbreaks. CONCLUSIONS: Many ship-associated outbreaks could have been prevented if measures had been taken to ensure adequate temperature control, avoidance of cross-contamination, reliable food sources, adequate heat treatment, and exclusion of infected food handlers from work. PMID:15219800

A review of outbreaks of foodborne disease associated with passenger ships: evidence for risk management.

PubMed

Rooney, Roisin M; Cramer, Elaine H; Mantha, Stacey; Nichols, Gordon; Bartram, Jamie K; Farber, Jeffrey M; Benembarek, Peter K

2004-01-01

Foodborne disease outbreaks on ships are of concern because of their potentially serious health consequences for passengers and crew and high costs to the industry. The authors conducted a review of outbreaks of foodborne diseases associated with passenger ships in the framework of a World Health Organization project on setting guidelines for ship sanitation. The authors reviewed data on 50 outbreaks of foodborne disease associated with passenger ships. For each outbreak, data on pathogens/toxins, type of ship, factors contributing to outbreaks, mortality and morbidity, and food vehicles were collected. The findings of this review show that the majority of reported outbreaks were associated with cruise ships and that almost 10,000 people were affected. Salmonella spp were most frequently associated with outbreaks. Foodborne outbreaks due to enterotoxigenic E. coli spp, Shigella spp, noroviruses (formally called Norwalk-like viruses), Vibrio spp, Staphylococcus aureus, Clostridium perfringens, Cyclospora sp, and Trichinella sp also occurred on ships. Factors associated with the outbreaks reviewed include inadequate temperature control, infected food handlers, contaminated raw ingredients, cross-contamination, inadequate heat treatment, and onshore excursions. Seafood was the most common food vehicle implicated in outbreaks. Many ship-associated outbreaks could have been prevented if measures had been taken to ensure adequate temperature control, avoidance of cross-contamination, reliable food sources, adequate heat treatment, and exclusion of infected food handlers from work.

Ultimate strength performance of tankers associated with industry corrosion addition practices

NASA Astrophysics Data System (ADS)

Kim, Do Kyun; Kim, Han Byul; Zhang, Xiaoming; Li, Chen Guang; Paik, Jeom Kee

2014-09-01

In the ship and offshore structure design, age-related problems such as corrosion damage, local denting, and fatigue damage are important factors to be considered in building a reliable structure as they have a significant influence on the residual structural capacity. In shipping, corrosion addition methods are widely adopted in structural design to prevent structural capacity degradation. The present study focuses on the historical trend of corrosion addition rules for ship structural design and investigates their effects on the ultimate strength performance such as hull girder and stiffened panel of double hull oil tankers. Three types of rules based on corrosion addition models, namely historic corrosion rules (pre-CSR), Common Structural Rules (CSR), and harmonised Common Structural Rules (CSRH) are considered and compared with two other corrosion models namely UGS model, suggested by the Union of Greek Shipowners (UGS), and Time-Dependent Corrosion Wastage Model (TDCWM). To identify the general trend in the effects of corrosion damage on the ultimate longitudinal strength performance, the corrosion addition rules are applied to four representative sizes of double hull oil tankers namely Panamax, Aframax, Suezmax, and VLCC. The results are helpful in understanding the trend of corrosion additions for tanker structures

Improved model for detection of homogeneous production batches of electronic components

NASA Astrophysics Data System (ADS)

Kazakovtsev, L. A.; Orlov, V. I.; Stashkov, D. V.; Antamoshkin, A. N.; Masich, I. S.

2017-10-01

Supplying the electronic units of the complex technical systems with electronic devices of the proper quality is one of the most important problems for increasing the whole system reliability. Moreover, for reaching the highest reliability of an electronic unit, the electronic devices of the same type must have equal characteristics which assure their coherent operation. The highest homogeneity of the characteristics is reached if the electronic devices are manufactured as a single production batch. Moreover, each production batch must contain homogeneous raw materials. In this paper, we propose an improved model for detecting the homogeneous production batches of shipped lot of electronic components based on implementing the kurtosis criterion for the results of non-destructive testing performed for each lot of electronic devices used in the space industry.

Integration of SAR and AIS for ship detection and identification

NASA Astrophysics Data System (ADS)

Yang, Chan-Su; Kim, Tae-Ho

2012-06-01

This abstract describes the preliminary design concept for an integration system of SAR and AIS data. SAR sensors are used to acquire image data over large coverage area either through the space borne or airborne platforms in UTC. AIS reports should also obtained on the same date as of the SAR acquisition for the purpose to perform integration test. Once both data reports are obtained, one need to match the timings of AIS data acquisition over the SAR image acquisition time with consideration of local time & boundary to extract the closest time signal from AIS report in order to know the AIS based ship positions, but still one cannot be able to distinguish which ships have the AIS transponder after projection of AIS based position onto the SAR image acquisition boundary. As far as integration is concerned, the ship dead-reckoning concept is most important forecasted position which provides the AIS based ship position at the time of SAR image acquisition and also provides the hints for azimuth shift which occurred in SAR image for the case of moving ships which moves in the direction perpendicular to the direction of flight path. Unknown ship's DR estimation is to be carried out based on the initial positions, speed and course over ground, which has already been shorted out from AIS reports, during the step of time matching. This DR based ship's position will be the candidate element for searching the SAR based ship targets for the purpose of identification & matching within the certain boundary around DR. The searching method is performed by means of estimation of minimum distance from ship's DR to SAR based ship position, and once it determines, so the candidate element will look for matching like ship size match of DR based ship's dimension wrt SAR based ship's edge, there may be some error during the matching with SAR based ship edges with actual ship's hull design as per the longitudinal and transverse axis size information obtained from the AIS reports due to blurring effect in SAR based ship signatures, once the conditions are satisfied, candidate element will move & shift over the SAR based ship signature target with the minimum displacement and it is known to be the azimuth shift compensation and this overall methodology are known to be integration of AIS report data over the SAR image acquisition boundary with assessment of time matching. The expected result may provide the good accuracy of the SAR and AIS contact position along with dimension and classification of ships over SAR image. There may be possibilities of matching speed and course from candidate element with SAR based ship signature, but still the challenges are presents in front of us that to estimation of speed and course by means of SAR data, if it may be possible so the expected final result may be more accurate as due to extra matching effects and the results may be used for the near real time performance for ship identification with help of integrated system design based on SAR and AIS data reports.

Human Reliability and Ship Stability

DTIC Science & Technology

2003-07-04

models such as Miller (1957) and Broadbent (1959) is the idea of human beings as limited capacity information processors with constraints on...15 4.2.2 Outline of Some Key models ...23 TABLE 11: GENERIC ERROR MODELING SYSTEM

Effect of Processing Parameters on Reliability of VARTM/SCRIMP Composite Panels - Phase 1

DTIC Science & Technology

2007-07-01

used in this program (Hess and Beach, 2000). The structural risks associated with new FRP composite ship structures can be mitigated by...reliability calibration of new designs. This program focuses on addressing the first and second tasks outlined above. 1.2. Phase I - Objectives The...Accomplishments: Tension Testing An optimized geometry for tension coupon testing was developed for marine grade composites. The new geometry reduces

The computer coordination method and research of inland river traffic based on ship database

NASA Astrophysics Data System (ADS)

Liu, Shanshan; Li, Gen

2018-04-01

A computer coordinated management method for inland river ship traffic is proposed in this paper, Get the inland ship's position, speed and other navigation information by VTS, building ship's statics and dynamic data bases, writing a program of computer coordinated management of inland river traffic by VB software, Automatic simulation and calculation of the meeting states of ships, Providing ship's long-distance collision avoidance information. The long-distance collision avoidance of ships will be realized. The results show that, Ships avoid or reduce meetings, this method can effectively control the macro collision avoidance of ships.

41 CFR 102-117.145 - What are coastwise laws?

Code of Federal Regulations, 2011 CFR

2011-01-01

... by water between points in the United States or its territories. The purpose of these laws is to assure reliable shipping service and the existence of a maritime capability in times of war or national...

Navy-Marine Corps Amphibious and Maritime Prepositioning Ship Programs: Background and Oversight Issues for Congress

DTIC Science & Technology

2006-07-26

FY2008. Although the Navy’s proposed force of 31 amphibious ships includes 10 LPD-17 class ships, the Navy is planning to end LPD-17 procurement in...expresses concerns about the planned reduction in amphibious ships, the sea basing concept, and the MPF(F) program, and requires a report on sea basing...Ship Force Structure Plan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Sea Basing Concept of Operations

Hospital ships adrift? Part 1: a systematic literature review characterizing US Navy hospital ship humanitarian and disaster response, 2004-2012.

PubMed

Licina, Derek

2013-06-01

United States foreign policy is tied extensively to health initiatives, many related to the use of military assets. Despite substantial resource investment by the US Department of Defense (DoD) in hospital ship humanitarian assistance and disaster response missions, the impact of this investment is unclear. A systematic literature review of both peer-reviewed and grey literature using eight databases representing the international community and multiple sectors was conducted. Data on the characteristics of missions directly related to US Navy hospital ship humanitarian assistance and disaster response from 2004-2012 were extracted and documented. Of the 1445 sources reviewed, a total of 43 publications met criteria for review. Six (13.9%) met empirical documentation criteria and 37 (86.0%) were considered nonempirical expert opinions and anecdotal accounts that were primarily descriptive in nature. Overall, disaster response accounted for 67.4% (29/43) and humanitarian assistance 25.6% (11/43). Public and private sector participants produced 79.0% (34/43) and 20.9% (9/43) of the publications respectively. Of private sector publications, 88.9% (8/9) focused on disaster response compared to 61.8% (21/34) from the public sector. Of all publications meeting inclusion criteria, 81.4% (35/43) focused on medical care, 9.3% (4/43) discussed partnerships, 4.7% (2/43) training, and 4.7% (2/43) medical ethics and strategic utilization. No primary author publications from the diplomatic, development, or participating host nations were identified. One (2.3%) of the 43 publications was from a partner nation participant. Discussion Without rigorous research methods yielding valid and reliable data-based information pertaining to Navy hospital ship mission impact, policy makers are left with anecdotal reports to influence their decision-making processes. This is inadequate considering the frequency of hospital ship deployments used as a foreign policy tool and the considerable funding that is involved in each mission. Future research efforts should study empirically the short- and long-term impacts of hospital ship missions in building regional and civil-military partnerships while meeting the humanitarian and disaster response needs of host nation populations.

Finite element analysis of container ship's cargo hold using ANSYS and POSEIDON software

NASA Astrophysics Data System (ADS)

Tanny, Tania Tamiz; Akter, Naznin; Amin, Osman Md.

2017-12-01

Nowadays ship structural analysis has become an integral part of the preliminary ship design providing further support for the development and detail design of ship structures. Structural analyses of container ship's cargo holds are carried out for the balancing of their safety and capacity, as those ships are exposed to the high risk of structural damage during voyage. Two different design methodologies have been considered for the structural analysis of a container ship's cargo hold. One is rule-based methodology and the other is a more conventional software based analyses. The rule based analysis is done by DNV-GL's software POSEIDON and the conventional package based analysis is done by ANSYS structural module. Both methods have been applied to analyze some of the mechanical properties of the model such as total deformation, stress-strain distribution, Von Mises stress, Fatigue etc., following different design bases and approaches, to indicate some guidance's for further improvements in ship structural design.

Uncertainty quantification and reliability assessment in operational oil spill forecast modeling system.

PubMed

Hou, Xianlong; Hodges, Ben R; Feng, Dongyu; Liu, Qixiao

2017-03-15

As oil transport increasing in the Texas bays, greater risks of ship collisions will become a challenge, yielding oil spill accidents as a consequence. To minimize the ecological damage and optimize rapid response, emergency managers need to be informed with how fast and where oil will spread as soon as possible after a spill. The state-of-the-art operational oil spill forecast modeling system improves the oil spill response into a new stage. However uncertainty due to predicted data inputs often elicits compromise on the reliability of the forecast result, leading to misdirection in contingency planning. Thus understanding the forecast uncertainty and reliability become significant. In this paper, Monte Carlo simulation is implemented to provide parameters to generate forecast probability maps. The oil spill forecast uncertainty is thus quantified by comparing the forecast probability map and the associated hindcast simulation. A HyosPy-based simple statistic model is developed to assess the reliability of an oil spill forecast in term of belief degree. The technologies developed in this study create a prototype for uncertainty and reliability analysis in numerical oil spill forecast modeling system, providing emergency managers to improve the capability of real time operational oil spill response and impact assessment. Copyright © 2017 Elsevier Ltd. All rights reserved.

Integrated crystal mounting and alignment system for high-throughput biological crystallography

DOEpatents

Nordmeyer, Robert A.; Snell, Gyorgy P.; Cornell, Earl W.; Kolbe, William F.; Yegian, Derek T.; Earnest, Thomas N.; Jaklevich, Joseph M.; Cork, Carl W.; Santarsiero, Bernard D.; Stevens, Raymond C.

2007-09-25

A method and apparatus for the transportation, remote and unattended mounting, and visual alignment and monitoring of protein crystals for synchrotron generated x-ray diffraction analysis. The protein samples are maintained at liquid nitrogen temperatures at all times: during shipment, before mounting, mounting, alignment, data acquisition and following removal. The samples must additionally be stably aligned to within a few microns at a point in space. The ability to accurately perform these tasks remotely and automatically leads to a significant increase in sample throughput and reliability for high-volume protein characterization efforts. Since the protein samples are placed in a shipping-compatible layered stack of sample cassettes each holding many samples, a large number of samples can be shipped in a single cryogenic shipping container.

Integrated crystal mounting and alignment system for high-throughput biological crystallography

DOEpatents

Nordmeyer, Robert A.; Snell, Gyorgy P.; Cornell, Earl W.; Kolbe, William; Yegian, Derek; Earnest, Thomas N.; Jaklevic, Joseph M.; Cork, Carl W.; Santarsiero, Bernard D.; Stevens, Raymond C.

2005-07-19

A method and apparatus for the transportation, remote and unattended mounting, and visual alignment and monitoring of protein crystals for synchrotron generated x-ray diffraction analysis. The protein samples are maintained at liquid nitrogen temperatures at all times: during shipment, before mounting, mounting, alignment, data acquisition and following removal. The samples must additionally be stably aligned to within a few microns at a point in space. The ability to accurately perform these tasks remotely and automatically leads to a significant increase in sample throughput and reliability for high-volume protein characterization efforts. Since the protein samples are placed in a shipping-compatible layered stack of sample cassettes each holding many samples, a large number of samples can be shipped in a single cryogenic shipping container.

The influence of ship motion of manual control skills

NASA Technical Reports Server (NTRS)

Mcleod, P.; Poulton, C.; Duross, H.; Lewis, W.

1981-01-01

The effects of ship motion on a range of typical manual control skills were examined on the Warren Spring ship motion simulator driven in heave, pitch, and roll by signals taken from the frigate HMS Avenger at 13 m/s (25 knots) into a force 4 wind. The motion produced a vertical r.m.s. acceleration of 0.024g, mostly between 0.1 and 0.3 Hz, with comparatively little pitch or roll. A task involving unsupported arm movements was seriously affected by the motion; a pursuit tracking task showed a reliable decrement although it was still performed reasonably well (pressure and free moving tracking controls were affected equally by the motion); a digit keying task requiring ballistic hand movements was unaffected. There was no evidence that these effects were caused by sea sickness. The differing response to motion of the different tasks, from virtual destruction to no effect, suggests that a major benefit could come from an attempt to design the man/control interface onboard ship around motion resistant tasks.

Cost-effectiveness of reducing sulfur emissions from ships.

PubMed

Wang, Chengfeng; Corbett, James J; Winebrake, James J

2007-12-15

We model cost-effectiveness of control strategies for reducing SO2 emissions from U.S. foreign commerce ships traveling in existing European or hypothetical U.S. West Coast SO(x) Emission Control Areas (SECAs) under international maritime regulations. Variation among marginal costs of control for individual ships choosing between fuel-switching and aftertreatment reveals cost-saving potential of economic incentive instruments. Compared to regulations prescribing low sulfur fuels, a performance-based policy can save up to $260 million for these ships with 80% more emission reductions than required because least-cost options on some individual ships outperform standards. Optimal simulation of a market-based SO2 control policy for approximately 4,700 U.S. foreign commerce ships traveling in the SECAs in 2002 shows that SECA emissions control targets can be achieved by scrubbing exhaust gas of one out of ten ships with annual savings up to $480 million over performance-based policy. A market-based policy could save the fleet approximately $63 million annually under our best-estimate scenario. Spatial evaluation of ship emissions reductions shows that market-based instruments can reduce more SO2 closer to land while being more cost-effective for the fleet. Results suggest that combining performance requirements with market-based instruments can most effectively control SO2 emissions from ships.

Low-cost human motion capture system for postural analysis onboard ships

NASA Astrophysics Data System (ADS)

Nocerino, Erica; Ackermann, Sebastiano; Del Pizzo, Silvio; Menna, Fabio; Troisi, Salvatore

2011-07-01

The study of human equilibrium, also known as postural stability, concerns different research sectors (medicine, kinesiology, biomechanics, robotics, sport) and is usually performed employing motion analysis techniques for recording human movements and posture. A wide range of techniques and methodologies has been developed, but the choice of instrumentations and sensors depends on the requirement of the specific application. Postural stability is a topic of great interest for the maritime community, since ship motions can make demanding and difficult the maintenance of the upright stance with hazardous consequences for the safety of people onboard. The need of capturing the motion of an individual standing on a ship during its daily service does not permit to employ optical systems commonly used for human motion analysis. These sensors are not designed for operating in disadvantageous environmental conditions (water, wetness, saltiness) and with not optimal lighting. The solution proposed in this study consists in a motion acquisition system that could be easily usable onboard ships. It makes use of two different methodologies: (I) motion capture with videogrammetry and (II) motion measurement with Inertial Measurement Unit (IMU). The developed image-based motion capture system, made up of three low-cost, light and compact video cameras, was validated against a commercial optical system and then used for testing the reliability of the inertial sensors. In this paper, the whole process of planning, designing, calibrating, and assessing the accuracy of the motion capture system is reported and discussed. Results from the laboratory tests and preliminary campaigns in the field are presented.

The impacts of freight mode splitting on congestion, risk, and delivery reliability.

DOT National Transportation Integrated Search

2012-09-01

Although splitting shipments across multiple delivery or transportation modes typically : increases total shipping costs as a result of diseconomies of scale, it may offer certain benefits : that can more than offset these costs. These benefits inclu...

A new rational-based optimal design strategy of ship structure based on multi-level analysis and super-element modeling method

NASA Astrophysics Data System (ADS)

Sun, Li; Wang, Deyu

2011-09-01

A new multi-level analysis method of introducing the super-element modeling method, derived from the multi-level analysis method first proposed by O. F. Hughes, has been proposed in this paper to solve the problem of high time cost in adopting a rational-based optimal design method for ship structural design. Furthermore, the method was verified by its effective application in optimization of the mid-ship section of a container ship. A full 3-D FEM model of a ship, suffering static and quasi-static loads, was used as the analyzing object for evaluating the structural performance of the mid-ship module, including static strength and buckling performance. Research results reveal that this new method could substantially reduce the computational cost of the rational-based optimization problem without decreasing its accuracy, which increases the feasibility and economic efficiency of using a rational-based optimal design method in ship structural design.

Lyophilization and Reconstitution of Reverse Osmosis Concentrated Natural Organic Matter

EPA Science Inventory

Disinfection by-product (DBP) research can be complicated by difficulties in shipping large water quantities and changing natural organic matter (NOM) characteristics over time. To overcome these issues, it is advantageous to have a reliable method for concentrating and preservin...

Transportation of Organs by Air: Safety, Quality, and Sustainability Criteria.

PubMed

Mantecchini, L; Paganelli, F; Morabito, V; Ricci, A; Peritore, D; Trapani, S; Montemurro, A; Rizzo, A; Del Sordo, E; Gaeta, A; Rizzato, L; Nanni Costa, A

2016-03-01

The outcomes of organ transplantation activities are greatly affected by the ability to haul organs and medical teams quickly and safely. Organ allocation and usage criteria have greatly improved over time, whereas the same result has not been achieved so far from the transport point of view. Safety and the highest level of service and efficiency must be reached to grant transplant recipients the healthiest outcome. The Italian National Transplant Centre (CNT), in partnership with the regions and the University of Bologna, has promoted a thorough analysis of all stages of organ transportation logistics chains to produce homogeneous and shared guidelines throughout the national territory, capable of ensuring safety, reliability, and sustainability at the highest levels. The mapping of all 44 transplant centers and the pertaining airport network has been implemented. An analysis of technical requirements among organ shipping agents at both national and international level has been promoted. A national campaign of real-time monitoring of organ transport activities at all stages of the supply chain has been implemented. Parameters investigated have been hospital and region of both origin and destination, number and type of organs involved, transport type (with or without medical team), stations of arrival and departure, and shipping agents, as well as actual times of activities involved. National guidelines have been issued to select organ storage units and shipping agents on the basis of evaluation of efficiency, reliability, and equipment with reference to organ type and ischemia time. Guidelines provide EU-level standards on technical equipment of aircrafts, professional requirements of shipping agencies and cabin crew, and requirements on service provision, including pricing criteria. The introduction in the Italian legislation of guidelines issuing minimum requirements on topics such as the medical team, packaging, labeling, safety and integrity, identification, real-time monitoring of temperature, and traceability of the organ during the logistics chain is deemed a valid response to the necessity of improving safety, reliability, and sustainability of organ transplantation activities in Italy. Copyright © 2016 Elsevier Inc. All rights reserved.

Monitoring Anthropogenic Ocean Sound from Shipping Using an Acoustic Sensor Network and a Compressive Sensing Approach.

PubMed

Harris, Peter; Philip, Rachel; Robinson, Stephen; Wang, Lian

2016-03-22

Monitoring ocean acoustic noise has been the subject of considerable recent study, motivated by the desire to assess the impact of anthropogenic noise on marine life. A combination of measuring ocean sound using an acoustic sensor network and modelling sources of sound and sound propagation has been proposed as an approach to estimating the acoustic noise map within a region of interest. However, strategies for developing a monitoring network are not well established. In this paper, considerations for designing a network are investigated using a simulated scenario based on the measurement of sound from ships in a shipping lane. Using models for the sources of the sound and for sound propagation, a noise map is calculated and measurements of the noise map by a sensor network within the region of interest are simulated. A compressive sensing algorithm, which exploits the sparsity of the representation of the noise map in terms of the sources, is used to estimate the locations and levels of the sources and thence the entire noise map within the region of interest. It is shown that although the spatial resolution to which the sound sources can be identified is generally limited, estimates of aggregated measures of the noise map can be obtained that are more reliable compared with those provided by other approaches.

Wavelet-based information filtering for fault diagnosis of electric drive systems in electric ships.

PubMed

Silva, Andre A; Gupta, Shalabh; Bazzi, Ali M; Ulatowski, Arthur

2017-09-22

Electric machines and drives have enjoyed extensive applications in the field of electric vehicles (e.g., electric ships, boats, cars, and underwater vessels) due to their ease of scalability and wide range of operating conditions. This stems from their ability to generate the desired torque and power levels for propulsion under various external load conditions. However, as with the most electrical systems, the electric drives are prone to component failures that can degrade their performance, reduce the efficiency, and require expensive maintenance. Therefore, for safe and reliable operation of electric vehicles, there is a need for automated early diagnostics of critical failures such as broken rotor bars and electrical phase failures. In this regard, this paper presents a fault diagnosis methodology for electric drives in electric ships. This methodology utilizes the two-dimensional, i.e. scale-shift, wavelet transform of the sensor data to filter optimal information-rich regions which can enhance the diagnosis accuracy as well as reduce the computational complexity of the classifier. The methodology was tested on sensor data generated from an experimentally validated simulation model of electric drives under various cruising speed conditions. The results in comparison with other existing techniques show a high correct classification rate with low false alarm and miss detection rates. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

Fuzzy-logic-based network for complex systems risk assessment: application to ship performance analysis.

PubMed

Abou, Seraphin C

2012-03-01

In this paper, a new interpretation of intuitionistic fuzzy sets in the advanced framework of the Dempster-Shafer theory of evidence is extended to monitor safety-critical systems' performance. Not only is the proposed approach more effective, but it also takes into account the fuzzy rules that deal with imperfect knowledge/information and, therefore, is different from the classical Takagi-Sugeno fuzzy system, which assumes that the rule (the knowledge) is perfect. We provide an analytical solution to the practical and important problem of the conceptual probabilistic approach for formal ship safety assessment using the fuzzy set theory that involves uncertainties associated with the reliability input data. Thus, the overall safety of the ship engine is investigated as an object of risk analysis using the fuzzy mapping structure, which considers uncertainty and partial truth in the input-output mapping. The proposed method integrates direct evidence of the frame of discernment and is demonstrated through references to examples where fuzzy set models are informative. These simple applications illustrate how to assess the conflict of sensor information fusion for a sufficient cooling power system of vessels under extreme operation conditions. It was found that propulsion engine safety systems are not only a function of many environmental and operation profiles but are also dynamic and complex. Copyright © 2011 Elsevier Ltd. All rights reserved.

Monitoring Anthropogenic Ocean Sound from Shipping Using an Acoustic Sensor Network and a Compressive Sensing Approach †

PubMed Central

Harris, Peter; Philip, Rachel; Robinson, Stephen; Wang, Lian

2016-01-01

Monitoring ocean acoustic noise has been the subject of considerable recent study, motivated by the desire to assess the impact of anthropogenic noise on marine life. A combination of measuring ocean sound using an acoustic sensor network and modelling sources of sound and sound propagation has been proposed as an approach to estimating the acoustic noise map within a region of interest. However, strategies for developing a monitoring network are not well established. In this paper, considerations for designing a network are investigated using a simulated scenario based on the measurement of sound from ships in a shipping lane. Using models for the sources of the sound and for sound propagation, a noise map is calculated and measurements of the noise map by a sensor network within the region of interest are simulated. A compressive sensing algorithm, which exploits the sparsity of the representation of the noise map in terms of the sources, is used to estimate the locations and levels of the sources and thence the entire noise map within the region of interest. It is shown that although the spatial resolution to which the sound sources can be identified is generally limited, estimates of aggregated measures of the noise map can be obtained that are more reliable compared with those provided by other approaches. PMID:27011187

Assessment of GNSS-based height data of multiple ships for measuring and forecasting great tsunamis

NASA Astrophysics Data System (ADS)

Inazu, Daisuke; Waseda, Takuji; Hibiya, Toshiyuki; Ohta, Yusaku

2016-12-01

Ship height positioning by the Global Navigation Satellite System (GNSS) was investigated for measuring and forecasting great tsunamis. We first examined GNSS height-positioning data of a navigating vessel. If we use the kinematic precise point positioning (PPP) method, tsunamis greater than 10-1 m will be detected by ship height positioning. Based on Automatic Identification System (AIS) data, we found that tens of cargo ships and tankers are usually identified to navigate over the Nankai Trough, southwest Japan. We assumed that a future Nankai Trough great earthquake tsunami will be observed by the kinematic PPP height positioning of an AIS-derived ship distribution, and examined the tsunami forecast capability of the offshore tsunami measurements based on the PPP-based ship height. A method to estimate the initial tsunami height distribution using offshore tsunami observations was used for forecasting. Tsunami forecast tests were carried out using simulated tsunami data by the PPP-based ship height of 92 cargo ships/tankers, and by currently operating deep-sea pressure and Global Positioning System (GPS) buoy observations at 71 stations over the Nankai Trough. The forecast capability using the PPP-based height of the 92 ships was shown to be comparable to or better than that using the operating offshore observatories at the 71 stations. We suppose that, immediately after the occurrence of a great earthquake, stations receiving successive ship information (AIS data) along certain areas of the coast would fail to acquire ship data due to strong ground shaking, especially near the epicenter. Such a situation would significantly deteriorate the tsunami-forecast capability using ship data. On the other hand, operational real-time analysis of seismic/geodetic data would be carried out for estimating a tsunamigenic fault model. Incorporating the seismic/geodetic fault model estimation into the tsunami forecast above possibly compensates for the deteriorated forecast capability.

Identification of SHIP-1 and SHIP-2 homologs in channel catfish, Ictalurus punctatus

USDA-ARS?s Scientific Manuscript database

Src homology domain 2 (SH2) domain-containing inositol 5’-phosphatases (SHIP) proteins have diverse roles in signal transduction. SHIP-1 and SHIP-2 homologs were identified in channel catfish, Ictalurus punctatus, based on sequence homology to murine and human SHIP sequences. Full-length cDNAs for ...

Modelling the Arrival of Invasive Organisms via the International Marine Shipping Network: A Khapra Beetle Study

PubMed Central

Paini, Dean R.; Yemshanov, Denys

2012-01-01

Species can sometimes spread significant distances beyond their natural dispersal ability by anthropogenic means. International shipping routes and the transport of shipping containers, in particular are a commonly recognised pathway for the introduction of invasive species. Species can gain access to a shipping container and remain inside, hidden and undetected for long periods. Currently, government biosecurity agencies charged with intercepting and removing these invasive species when they arrive to a county’s border only assess the most immediate point of loading in evaluating a shipping container’s risk profile. However, an invasive species could have infested a container previous to this point and travelled undetected before arriving at the border. To assess arrival risk for an invasive species requires analysing the international shipping network in order to identify the most likely source countries and the domestic ports of entry where the species is likely to arrive. We analysed an international shipping network and generated pathway simulations using a first-order Markov chain model to identify possible source ports and countries for the arrival of Khapra beetle (Trogoderma granarium) to Australia. We found Kaohsiung (Taiwan) and Busan (Republic of Korea) to be the most likely sources for Khapra beetle arrival, while the port of Melbourne was the most likely point of entry to Australia. Sensitivity analysis revealed significant stability in the rankings of foreign and Australian ports. This methodology provides a reliable modelling tool to identify and rank possible sources for an invasive species that could arrive at some time in the future. Such model outputs can be used by biosecurity agencies concerned with inspecting incoming shipping containers and wishing to optimise their inspection protocols. PMID:22970258

Ozone production efficiency of a ship-plume: ITCT 2K2 case study.

PubMed

Kim, Hyun S; Kim, Yong H; Han, Kyung M; Kim, Jhoon; Song, Chul H

2016-01-01

Ozone production efficiency (OPE) of ship plume was first evaluated in this study, based on ship-plume photochemical/dynamic model simulations and the ship-plume composition data measured during the ITCT 2K2 (Intercontinental Transport and Chemical Transformation 2002) aircraft campaign. The averaged instantaneous OPEs (OPE(i)‾) estimated via the ship-plume photochemical/dynamic modeling for the ITCT 2K2 ship-plume ranged between 4.61 and 18.92, showing that the values vary with the extent of chemical evolution (or chemical stage) of the ship plume and the stability classes of the marine boundary layer (MBL). Together with OPE(i)‾, the equivalent OPEs (OPE(e)‾) for the entire ITCT 2K2 ship-plume were also estimated. The OPE(e)‾ values varied between 9.73 (for the stable MBL) and 12.73 (for the moderately stable MBL), which agreed well with the OPE(e)‾ of 12.85 estimated based on the ITCT 2K2 ship-plume observations. It was also found that both the model-simulated and observation-based OPE(e)‾ inside the ship-plume were 0.29-0.38 times smaller than the OPE(e)‾ calculated/measured outside the ITCT 2K2 ship-plume. Such low OPEs insides the ship plume were due to the high levels of NO and non-liner ship-plume photochemistry. Possible implications of this ship-plume OPE study in the global chemistry-transport modeling are also discussed. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

Chemical and Biological Defense: DOD Needs to Continue to Collect and Provide Information on Tests and Potentially Exposed Personnel

DTIC Science & Technology

2004-05-01

or Naval officer as test director. Ship-based tests were conducted in the open waters of the North Atlantic and Pacific Oceans and near the...BG, FP Oct. 9, 2002 (ship-based) Granville S. Hall and surround- ing waters and airspace A-4, F-105, and an Aero Commander 65-12, Devil Hole I...Apr.-May 1968 USS Carbonero, USS Oahu, Hawaii, BG June 30, 03 Arrow (ship-based) Granville S. Hall and surrounding waters 69-31 (ship-based) 313 Aug

26 CFR 1.955A-2 - Amount of a controlled foreign corporation's qualified investments in foreign base company...

Code of Federal Regulations, 2010 CFR

2010-04-01

... insure a source of supplies or services used in the conduct of foreign base company shipping operations... qualified investments in foreign base company shipping operations. 1.955A-2 Section 1.955A-2 Internal... investments in foreign base company shipping operations. (a) Qualified investments—(1) In general. Under...

Polar bear aerial survey in the eastern Chukchi Sea: A pilot study

USGS Publications Warehouse

Evans, Thomas J.; Fischbach, Anthony S.; Schliebe, Scott L.; Manly, Bryan; Kalxdorff, Susanne B.; York, Geoff S.

2003-01-01

Alaska has two polar bear populations: the Southern Beaufort Sea population, shared with Canada, and the Chukchi/Bering Seas population, shared with Russia. Currently a reliable population estimate for the Chukchi/Bering Seas population does not exist. Land-based aerial and mark-recapture population surveys may not be possible in the Chukchi Sea because variable ice conditions, the limited range of helicopters, extremely large polar bear home ranges, and severe weather conditions may limit access to remote areas. Thus line-transect aerial surveys from icebreakers may be the best available tool to monitor this polar bear stock. In August 2000, a line-transect survey was conducted in the eastern Chukchi Sea and western Beaufort Sea from helicopters based on a U.S. Coast Guard icebreaker under the "Ship of Opportunity" program. The objectives of this pilot study were to estimate polar bear density in the eastern Chukchi and western Beaufort Seas and to assess the logistical feasibility of using ship-based aerial surveys to develop polar bear population estimates. Twenty-nine polar bears in 25 groups were sighted on 94 transects (8257 km). The density of bears was estimated as 1 bear per 147 km² (CV = 38%). Additional aerial surveys in late fall, using dedicated icebreakers, would be required to achieve the number of sightings, survey effort, coverage, and precision needed for more effective monitoring of population trends in the Chukchi Sea.

Combining Ballast Water Exchange and Treatment To Maximize Prevention of Species Introductions to Freshwater Ecosystems.

PubMed

Briski, Elizabeta; Gollasch, Stephan; David, Matej; Linley, R Dallas; Casas-Monroy, Oscar; Rajakaruna, Harshana; Bailey, Sarah A

2015-08-18

The most effective way to manage species transfers is to prevent their introduction via vector regulation. Soon, international ships will be required to meet numeric ballast discharge standards using ballast water treatment (BWT) systems, and ballast water exchange (BWE), currently required by several countries, will be phased out. However, there are concerns that BWT systems may not function reliably in fresh and/or turbid water. A land-based evaluation of simulated "BWE plus BWT" versus "BWT alone" demonstrated potential benefits of combining BWE with BWT for protection of freshwater ecosystems. We conducted ship-based testing to compare the efficacy of "BWE plus BWT" versus "BWT alone" on voyages starting with freshwater ballast. We tested the hypotheses that there is an additional effect of "BWE plus BWT" compared to "BWT alone" on the reduction of plankton, and that taxa remaining after "BWE plus BWT" will be marine (low risk for establishment at freshwater recipient ports). Our study found that BWE has significant additional effect on the reduction of plankton, and this effect increases with initial abundance. As per expectations, "BWT alone" tanks contained higher risk freshwater or euryhaline taxa at discharge, while "BWE plus BWT" tanks contained mostly lower risk marine taxa unlikely to survive in recipient freshwater ecosystems.

Lyophilization and Reconstitution of Reverse-Osmosis Concentrated Natural Organic Matter from a Drinking Water Source

EPA Science Inventory

Disinfection by-product (DBP) research can be complicated by difficulties in shipping large water quantities and changing natural organic matter (NOM) characteristics over time. To overcome these issues, it is advantageous to have a reliable method for concentrating NOM with min...

Measuring and forecasting great tsunamis by GNSS-based vertical positioning of multiple ships

NASA Astrophysics Data System (ADS)

Inazu, D.; Waseda, T.; Hibiya, T.; Ohta, Y.

2016-12-01

Vertical ship positioning by the Global Navigation Satellite System (GNSS) was investigated for measuring and forecasting great tsunamis. We first examined existing GNSS vertical position data of a navigating vessel. The result indicated that by using the kinematic Precise Point Positioning (PPP) method, tsunamis greater than 10^-1 m can be detected from the vertical position of the ship. Based on Automatic Identification System (AIS) data, tens of cargo ships and tankers are regularly identified navigating over the Nankai Trough, southwest of Japan. We then assumed that a future Nankai Trough great earthquake tsunami will be observed by ships at locations based on AIS data. The tsunami forecast capability by these virtual offshore tsunami measurements was examined. A conventional Green's function based inversion was used to determine the initial tsunami height distribution. Tsunami forecast tests over the Nankai Trough were carried out using simulated tsunami data of the vertical positions of multiple cargo ships/tankers on a certain day, and of the currently operating observations by deep-sea pressure gauges and Global Positioning System (GPS) buoys. The forecast capability of ship-based tsunami height measurements alone was shown to be comparable to or better than that using the existing offshore observations.

Investigating Atmospheric Rivers using GPS PW from Ocean Transits

NASA Astrophysics Data System (ADS)

Almanza, V.; Foster, J. H.; Businger, S.

2014-12-01

Atmospheric Rivers (AR) can be described as a long narrow feature within a warm conveyor belt where anomalous precipitable water (PW) is transported from low to high latitudes. Close monitoring of ARs is heavily reliant on satellites, which are limited both in space and time, to capture the fluctuations PW particularly over the ocean. Ship-based Global Positioning System (GPS) receivers have been successful in obtaining millimeter PW accuracy within 100 km from the nearest ground-based reference receiver at a 30 second sampling rate. We extended this capability with a field experiment using ship-based GPS PW on board a cargo ship to traverse over the Eastern Pacific Ocean. In one 14-day cruise cycle, between the periods of February 3-16, 2014, the ship-based GPS captured PW spikes >50 mm during the early development of two ARs, which lead to moderate to heavy rainfall events for Hawaii and flood conditions along the West Coast of the United States. Comparisons between PW solutions processed using different GPS reference sites at distances 100-2000 km provided an internal validation for the ship-based GPS PW with errors typically less than 5 mm. Land-based observations provided an external validation and are in good agreement with ship-based GPS PW at distances <100 km from the coast, a zone heavily trafficked by cargo containers and a challenge area for satellite retrievals. From these preliminary results, commercial ship-based GPS receivers offer an extremely cost-effective approach for acquiring continuous meteorological observations over the oceans, which can provide important calibration/validation data for satellite retrieval algorithms. Ship-based systems could be particularly useful for augmenting our meteorological observing networks to improve weather prediction and nowcasting, which in turn provide critical support for hazard response and mitigation efforts in coastal regions.

Ship detection in optical remote sensing images based on deep convolutional neural networks

NASA Astrophysics Data System (ADS)

Yao, Yuan; Jiang, Zhiguo; Zhang, Haopeng; Zhao, Danpei; Cai, Bowen

2017-10-01

Automatic ship detection in optical remote sensing images has attracted wide attention for its broad applications. Major challenges for this task include the interference of cloud, wave, wake, and the high computational expenses. We propose a fast and robust ship detection algorithm to solve these issues. The framework for ship detection is designed based on deep convolutional neural networks (CNNs), which provide the accurate locations of ship targets in an efficient way. First, the deep CNN is designed to extract features. Then, a region proposal network (RPN) is applied to discriminate ship targets and regress the detection bounding boxes, in which the anchors are designed by intrinsic shape of ship targets. Experimental results on numerous panchromatic images demonstrate that, in comparison with other state-of-the-art ship detection methods, our method is more efficient and achieves higher detection accuracy and more precise bounding boxes in different complex backgrounds.

Shipping emissions and their impacts on air quality in China.

PubMed

Zhang, Yan; Yang, Xin; Brown, Richard; Yang, Liping; Morawska, Lidia; Ristovski, Zoran; Fu, Qingyan; Huang, Cheng

2017-03-01

China has >400 ports, is home to 7 of 10 biggest ports in the world and its waterway infrastructure construction has been accelerating over the past years. But the increasing number of ports and ships means increasing emissions, and in turn, increasing impact on local and regional air pollution. This paper presents an overview of the broad field of ship emissions in China and their atmospheric impacts, including topics of ship engine emissions and control, ship emission factors and their measurements, developing of ship emission inventories, shipping and port emissions of the main shipping areas in China, and quantitative contribution of shipping emissions to the local and regional air pollution. There have been an increasing number of studies published on all the above aspects, yet, this review identified some critical research gaps, filling of which is necessary for better control of ship emissions, and for lowering their impacts. In particular, there are very few studies on inland ports and river ships, and there are few national scale ship emission inventories available for China. While advanced method to estimate ship emission based on ship AIS activities makes it now possible to develop high spatial- and temporal-resolution emission inventories, the ship emission factors used in Chinese studies have been based mainly on foreign measurements. Further, the contribution of ship emissions to air pollution in coastal cities, the dispersion of pollution plumes emitted by ships, or the chemical evolution process along the transmission path, have so far not been systematically studied in China. Copyright © 2016 Elsevier B.V. All rights reserved.

Sea Basing and Alternatives for Deploying and Sustaining Ground Combat Forces

DTIC Science & Technology

2007-07-01

speed roll-on/roll-off ship (top) and an intratheater high - speed vessel (bottom) are shown alongside a notional mobile landing platform (center...F), might be needed to fully support sea-based ground forces. Those other ships could include tankers and high - speed ships for spe- cial cargo . The...maritime prepositioning squadron; T-HSS = high - speed ship ; TBD = to be determined. Vehicles Cargo Aircraft (Thousands of (Thousands

An Assessment of Vulnerabilities for Ship-based Control Systems

DTIC Science & Technology

2009-09-01

VULNERABILITIES FOR SHIP- BASED CONTROL SYSTEMS by Richard Bensing September 2009 Thesis Advisor: Karen Burke Co-Advisor: George Dinolt...COVERED Master’s Thesis 4. TITLE AND SUBTITLE: An Assessment of Vulnerabilities for Ship- based Control Systems 6. AUTHOR(S) Richard Bensing 5...soft underbelly. Computer- based control systems form the heart of the critical infrastructure, and these control systems are riddled with rampant

Using flight simulators aboard ships: human side effects of an optimal scenario with smooth seas.

PubMed

Muth, Eric R; Lawson, Ben

2003-05-01

The U.S. Navy is considering placing flight simulators aboard ships. It is known that certain types of flight simulators can elicit motion adaptation syndrome (MAS), and also that certain types of ship motion can cause MAS. The goal of this study was to determine if using a flight simulator during ship motion would cause MAS, even when the simulator stimulus and the ship motion were both very mild. All participants in this study completed three conditions. Condition 1 (Sim) entailed "flying" a personal computer-based flight simulator situated on land. Condition 2 (Ship) involved riding aboard a U.S. Navy Yard Patrol boat. Condition 3 (ShipSim) entailed "flying" a personal computer-based flight simulator while riding aboard a Yard Patrol boat. Before and after each condition, participants' balance and dynamic visual acuity were assessed. After each condition, participants filled out the Nausea Profile and the Simulator Sickness Questionnaire. Following exposure to a flight simulator aboard a ship, participants reported negligible symptoms of nausea and simulator sickness. However, participants exhibited a decrease in dynamic visual acuity after exposure to the flight simulator aboard ship (T[25] = 3.61, p < 0.05). Balance results were confounded by significant learning and, therefore, not interpretable. This study suggests that flight simulators can be used aboard ship. As a minimal safety precaution, these simulators should be used according to current safety practices for land-based simulators. Optimally, these simulators should be designed to minimize MAS, located near the ship's center of rotation and used when ship motion is not provocative.

An Adaptive Ship Detection Scheme for Spaceborne SAR Imagery

PubMed Central

Leng, Xiangguang; Ji, Kefeng; Zhou, Shilin; Xing, Xiangwei; Zou, Huanxin

2016-01-01

With the rapid development of spaceborne synthetic aperture radar (SAR) and the increasing need of ship detection, research on adaptive ship detection in spaceborne SAR imagery is of great importance. Focusing on practical problems of ship detection, this paper presents a highly adaptive ship detection scheme for spaceborne SAR imagery. It is able to process a wide range of sensors, imaging modes and resolutions. Two main stages are identified in this paper, namely: ship candidate detection and ship discrimination. Firstly, this paper proposes an adaptive land masking method using ship size and pixel size. Secondly, taking into account the imaging mode, incidence angle, and polarization channel of SAR imagery, it implements adaptive ship candidate detection in spaceborne SAR imagery by applying different strategies to different resolution SAR images. Finally, aiming at different types of typical false alarms, this paper proposes a comprehensive ship discrimination method in spaceborne SAR imagery based on confidence level and complexity analysis. Experimental results based on RADARSAT-1, RADARSAT-2, TerraSAR-X, RS-1, and RS-3 images demonstrate that the adaptive scheme proposed in this paper is able to detect ship targets in a fast, efficient and robust way. PMID:27563902

Global strength assessment in oblique waves of a large gas carrier ship, based on a non-linear iterative method

NASA Astrophysics Data System (ADS)

Domnisoru, L.; Modiga, A.; Gasparotti, C.

2016-08-01

At the ship's design, the first step of the hull structural assessment is based on the longitudinal strength analysis, with head wave equivalent loads by the ships' classification societies’ rules. This paper presents an enhancement of the longitudinal strength analysis, considering the general case of the oblique quasi-static equivalent waves, based on the own non-linear iterative procedure and in-house program. The numerical approach is developed for the mono-hull ships, without restrictions on 3D-hull offset lines non-linearities, and involves three interlinked iterative cycles on floating, pitch and roll trim equilibrium conditions. Besides the ship-wave equilibrium parameters, the ship's girder wave induced loads are obtained. As numerical study case we have considered a large LPG liquefied petroleum gas carrier. The numerical results of the large LPG are compared with the statistical design values from several ships' classification societies’ rules. This study makes possible to obtain the oblique wave conditions that are inducing the maximum loads into the large LPG ship's girder. The numerical results of this study are pointing out that the non-linear iterative approach is necessary for the computation of the extreme loads induced by the oblique waves, ensuring better accuracy of the large LPG ship's longitudinal strength assessment.

Infrared Ship Target Segmentation Based on Spatial Information Improved FCM.

PubMed

Bai, Xiangzhi; Chen, Zhiguo; Zhang, Yu; Liu, Zhaoying; Lu, Yi

2016-12-01

Segmentation of infrared (IR) ship images is always a challenging task, because of the intensity inhomogeneity and noise. The fuzzy C-means (FCM) clustering is a classical method widely used in image segmentation. However, it has some shortcomings, like not considering the spatial information or being sensitive to noise. In this paper, an improved FCM method based on the spatial information is proposed for IR ship target segmentation. The improvements include two parts: 1) adding the nonlocal spatial information based on the ship target and 2) using the spatial shape information of the contour of the ship target to refine the local spatial constraint by Markov random field. In addition, the results of K -means are used to initialize the improved FCM method. Experimental results show that the improved method is effective and performs better than the existing methods, including the existing FCM methods, for segmentation of the IR ship images.

Reliability - Based Performance Assessment of Damaged Ships

DTIC Science & Technology

2008-09-01

UJ UJ ’ LLJ u: UJ u LU UJ UJ UJ LU UJ LU ._ "D o O c o C Q 8 o 8 o o o o o o O 8 s 8 O o o o O 8 o U o OC -T Ch 5 •c 5 o oc -T 5 » ^c o OC -r * a- s...CN ^r CD CD s r- CO * i— O ^ •* CsJ m CO CN CM •* a> y 0) 5; N *-- (0 "" ^ CN CN (N ad S CD CO CN CO 1 *f CO CO r- i- oS *" •" CM o ca CO TD 5 TO

Radiated noise from commercial ships in the Gulf of Maine: implications for whale/vessel collisions.

PubMed

Allen, J Kaitlyn; Peterson, Michael L; Sharrard, George V; Wright, Dana L; Todd, Sean K

2012-09-01

To understand mysticete acoustic-based detection of ships, radiated noise from high-speed craft, cruise ships, catamarans and fishing vessels was recorded June-September 2009. Calibrated acoustic data (<2500 Hz) from a vertical hydrophone array was combined with ship passage information. A cruise ship had the highest broadband source level, while a fishing vessel had the lowest. Ship noise radiated asymmetrically and varied with depth. Bow null-effect acoustic shadow zones were observed for all ship classes and were correlated with ship-length-to-draft-ratios. These shadow zones may reduce ship detection by near-surface mysticetes.

Coherent acoustic communication in a tidal estuary with busy shipping traffic.

PubMed

van Walree, Paul A; Neasham, Jeffrey A; Schrijver, Marco C

2007-12-01

High-rate acoustic communication experiments were conducted in a dynamic estuarine environment. Two current profilers deployed in a shipping lane were interfaced with acoustic modems, which modulated and transmitted the sensor readings every 200 s over a period of four days. QPSK modulation was employed at a raw data rate of 8 kbits on a 12-kHz carrier. Two 16-element hydrophone arrays, one horizontal and one vertical, were deployed near the shore. A multichannel decision-feedback equalizer was used to demodulate the modem signals received on both arrays. Long-term statistical analysis reveals the effects of the tidal cycle, subsea unit location, attenuation by the wake of passing vessels, and high levels of ship-generated noise on the fidelity of the communication links. The use of receiver arrays enables vast improvement in the overall reliability of data delivery compared with a single-receiver system, with performance depending strongly on array orientation. The vertical array offers the best performance overall, although the horizontal array proves more robust against shipping noise. Spatial coherence estimates, variation of array aperture, and inspection of array angular responses point to adaptive beamforming and coherent combining as the chief mechanisms of array gain.

The activity-based methodology to assess ship emissions - A review.

PubMed

Nunes, R A O; Alvim-Ferraz, M C M; Martins, F G; Sousa, S I V

2017-12-01

Several studies tried to estimate atmospheric emissions with origin in the maritime sector, concluding that it contributed to the global anthropogenic emissions through the emission of pollutants that have a strong impact on hu' health and also on climate change. Thus, this paper aimed to review published studies since 2010 that used activity-based methodology to estimate ship emissions, to provide a summary of the available input data. After exclusions, 26 articles were analysed and the main information were scanned and registered, namely technical information about ships, ships activity and movement information, engines, fuels, load and emission factors. The larger part of studies calculating in-port ship emissions concluded that the majority was emitted during hotelling and most of the authors allocating emissions by ship type concluded that containerships were the main pollutant emitters. To obtain technical information about ships the combined use of data from Lloyd's Register of Shipping database with other sources such as port authority's databases, engine manufactures and ship-owners seemed the best approach. The use of AIS data has been growing in recent years and seems to be the best method to report activities and movements of ships. To predict ship powers the Hollenbach (1998) method which estimates propelling power as a function of instantaneous speed based on total resistance and use of load balancing schemes for multi-engine installations seemed to be the best practices for more accurate ship emission estimations. For emission factors improvement, new on-board measurement campaigns or studies should be undertaken. Regardless of the effort that has been performed in the last years to obtain more accurate shipping emission inventories, more precise input data (technical information about ships, engines, load and emission factors) should be obtained to improve the methodology to develop global and universally accepted emission inventories for an effective environmental policy plan. Copyright © 2017 Elsevier Ltd. All rights reserved.

Prediction of the Main Engine Power of a New Container Ship at the Preliminary Design Stage

NASA Astrophysics Data System (ADS)

Cepowski, Tomasz

2017-06-01

The paper presents mathematical relationships that allow us to forecast the estimated main engine power of new container ships, based on data concerning vessels built in 2005-2015. The presented approximations allow us to estimate the engine power based on the length between perpendiculars and the number of containers the ship will carry. The approximations were developed using simple linear regression and multivariate linear regression analysis. The presented relations have practical application for estimation of container ship engine power needed in preliminary parametric design of the ship. It follows from the above that the use of multiple linear regression to predict the main engine power of a container ship brings more accurate solutions than simple linear regression.

Characteristics and triage of a maritime disaster: an accidental passenger ship collision in Korea.

PubMed

Ryu, Ji Ho; Yeom, Seok Ran; Jeong, Jin Woo; Kim, Yong In; Cho, Suck Ju

2010-06-01

The aim of this study was to analyze the characteristics of and responses to a maritime disaster, by reviewing the events surrounding the accidental collision of a high-speed passenger ship in South Korea. Of the 215 boarded passengers on a high-speed passenger ship sailing from Fukuoka to Busan, we retrospectively examined information of 114 victims of the ship's collision with a whale on 12 April 2007. We referenced reports from the on-site disaster medical assistance team members; recorded notifications to the Busan 1339 Emergency Medical Information Centre, from the scene of the accident and data from the ship's insurer. The 114 victims were transported to 20 different hospitals. Many patients were transported to nearby local hospitals from the scene of the accident; other patients were transported to more distant hospitals. Eighty-five patients were transported to hospitals through mobile emergency support units, whereas the other patients were transported directly by fire officers from the 119 Fire Officer Centre. One patient died in the transport. In conclusion, our national emergency medical service and disaster response system each suffer from many problems - especially a lack of cooperation among related departments and insufficient communication therein. The onboard planning and practice of a disaster plan is required, and a reliable information system between the scene of a maritime disaster and our emergency medical service system should be developed.

A CBO Study. Sea Basing and Alternatives for Deploying and Sustaining Ground Combat Forces

DTIC Science & Technology

2007-07-01

ships in the planned MPF(F) will not be large enough to receive aircraft capable of delivering cargo over intercontinental ranges. A high - speed ... speed roll-on/roll-off ship (top) and an intratheater high - speed vessel (bottom) are shown alongside a notional mobile landing platform (center) with...might be needed to fully support sea-based ground forces. Those other ships could include tankers and high - speed ships for spe- cial

Countermeasure effectiveness against an intelligent imaging infrared anti-ship missile

NASA Astrophysics Data System (ADS)

Gray, Greer J.; Aouf, Nabil; Richardson, Mark; Butters, Brian; Walmsley, Roy

2013-02-01

Ship self defense against heat-seeking anti-ship missiles is of great concern to modern naval forces. One way of protecting ships against these threats is to use infrared (IR) offboard countermeasures. These decoys need precise placement to maximize their effectiveness, and simulation is an invaluable tool used in determining optimum deployment strategies. To perform useful simulations, high-fidelity models of missiles are required. We describe the development of an imaging IR anti-ship missile model for use in countermeasure effectiveness simulations. The missile model's tracking algorithm is based on a target recognition system that uses a neural network to discriminate between ships and decoys. The neural network is trained on shape- and intensity-based features extracted from simulated imagery. The missile model is then used within ship-decoy-missile engagement simulations, to determine how susceptible it is to the well-known walk-off seduction countermeasure technique. Finally, ship survivability is improved by adjusting the decoy model to increase its effectiveness against the tracker.

Intelligent ship traffic monitoring for oil spill prevention: risk based decision support building on AIS.

PubMed

Eide, Magnus S; Endresen, Oyvind; Brett, Per Olaf; Ervik, Jon Leon; Røang, Kjell

2007-02-01

The paper describes a model, which estimates the risk levels of individual crude oil tankers. The intended use of the model, which is ready for trial implementation at The Norwegian Coastal Administrations new Vardø VTS (Vessel Traffic Service) centre, is to facilitate the comparison of ships and to support a risk based decision on which ships to focus attention on. For a VTS operator, tasked with monitoring hundreds of ships, this is a valuable decision support tool. The model answers the question, "Which ships are likely to produce an oil spill accident, and how much is it likely to spill?".

Ship navigation using Navstar GPS - An application study

NASA Technical Reports Server (NTRS)

Mohan, S. N.

1982-01-01

Ocean current measurement applications in physical oceanography require knowledge of inertial ship velocity to a precision of 1-2 cm/sec over a typical five minute averaging interval. The navigation accuracy must be commensurate with data precision obtainable from ship borne acoustic profilers used in sensing ocean currents. The Navstar Global Positioning System is viewed as a step in user technological simplification, extension in coverage availability, and enhancement in performance accuracy as well as reliability over the existing systems, namely, Loran-C, Transit, and Omega. Error analyses have shown the possibility of attaining the 1-2 cm/sec accuracy during active GPS coverage at a data rate of four position fixes per minute under varying sea-states. This paper is intended to present results of data validation exercises leading to design of an experiment at sea for deployment of both a GPS y-set and a direct Doppler measurement system as the autonomous navigation system used in conjunction with an acoustic Doppler as the sensor for ocean current measurement.

Design of a real-time system of moving ship tracking on-board based on FPGA in remote sensing images

NASA Astrophysics Data System (ADS)

Yang, Tie-jun; Zhang, Shen; Zhou, Guo-qing; Jiang, Chuan-xian

2015-12-01

With the broad attention of countries in the areas of sea transportation and trade safety, the requirements of efficiency and accuracy of moving ship tracking are becoming higher. Therefore, a systematic design of moving ship tracking onboard based on FPGA is proposed, which uses the Adaptive Inter Frame Difference (AIFD) method to track a ship with different speed. For the Frame Difference method (FD) is simple but the amount of computation is very large, it is suitable for the use of FPGA to implement in parallel. But Frame Intervals (FIs) of the traditional FD method are fixed, and in remote sensing images, a ship looks very small (depicted by only dozens of pixels) and moves slowly. By applying invariant FIs, the accuracy of FD for moving ship tracking is not satisfactory and the calculation is highly redundant. So we use the adaptation of FD based on adaptive extraction of key frames for moving ship tracking. A FPGA development board of Xilinx Kintex-7 series is used for simulation. The experiments show that compared with the traditional FD method, the proposed one can achieve higher accuracy of moving ship tracking, and can meet the requirement of real-time tracking in high image resolution.

Point-of-care syndrome-based, rapid diagnosis of infections on commercial ships.

PubMed

Bouricha, Mehdi; Samad, Marc Abdul; Levy, Pierre-Yves; Raoult, Didier; Drancourt, Michel

2014-01-01

Suspicion of contagious disease on commercial ships tends to be poorly managed, as there is little capacity to confirm a case on board except for malaria. Here we implemented a point-of-care (POC) laboratory on one container ship and one cruise ship for the rapid syndrome-based diagnosis of infectious diseases on board. In 2012 we implemented a POC laboratory on board a freight ship and on board a cruise ship. The POC laboratory ran a total of six different color-coded, syndrome-based kits incorporating 10 different commercially available immunochromatographic tests. The POC tests were taught within 1-hour as part of training to staff without any previous knowledge in microbiology. Compared with terrestrial POCs, specific constraints included the necessity to secure POC devices into the motile ship, to use robust devices, to overcome difficulties in communicating with the core laboratory, and to overcome limited intimacy of patients. However, a total of 36 POC tests were easily performed and yielded contributive negative results. This first experiment indicates that it is possible to run POC laboratories by nonexpert staff after providing rapid teaching course on board commercial ships. Generalization of on-board POC laboratories is expected to help in improving the medical management of staff and passengers. © 2013 International Society of Travel Medicine.

Quantification of Shipping Emissions in the Eastern Mediterranean and Comparison with Satellite Observations

NASA Astrophysics Data System (ADS)

Kilic, A.; Unal, A.; Kindap, T.; Karaca, M.; Khan, M. N.

2010-12-01

Shipping is considered as one of the main emission sources worldwide. Recent studies suggest that, in the Mediterrenean, ship emissions are responsible for 10-50% of black carbon, 2-12% ozone in the surface layer and 5-20% for nitrogen dioxide atmospheric column burden (Marmer et al., 2009). It is, therefore, essential to have an accurate emissions estimation for ships. Marmara Sea, an inland sea connecting the Mediterrenean to the Black Sea, has significant marine activity. Marmara region, surrounding the Marmara Sea, has over 30 million population (including Istanbul megacity) with significant emission sources (e.g., on-road traffic, industry). Emission amounts from ships can be calculated based on two different methodologies, one is according to the total amount of bunker fuels for maritime transport sold which is called top down approach and the other is shipping activity-based bottom-up approach. The top-down estimation method is not suitable for calculations of shipping emissions in Turkey since fuel sales cannot be accurately obtained. Also, top-down approaches possibly have some errors, since data assumptions for the average engine power, engine operating hours and emission factors are the most important uncertain inputs. Previously, a few studies based on bottom-up aproach have been carried on about shipping emissions in Marmara Sea according to the shipping statistics belong to Istanbul and Canakkale Straits and port regions. These studies were mainly depending on very rough assumptions such as avearage ship speed, fixed ships routes, generalized engine types and average fuel consumptions. Deniz C. (2008) estimated shipping emissions in 2003, for Marmara Sea and Turkish Straits as 111,000 tons for NOx, 87,000 tons for SO2, 5,451,000 tons for CO2, 4762 tons for PM. Although- between 2003 and 2008- there is approximately 15% increase in number of ships passsing through Turkish Straits, this study shows that, shippings emissions for the same region are estimated to be more than 3 times of previous studies. In this study, Automatic Information System (AIS) records of marine vessels (having 1 minute temporal resolution) for over 10,000 ships operating at the study area (including Marmara Sea, Istanbul and Canakkale Straits and some parts of Black Sea and Aegian Sea) were obtained from Turkish Undersecretariat for Maritime Affairs for the period between August 2008 and August 2009. These records include the position of the ships, gross tonnage and ship types. Using energy based emission factors for each operation mode, minute-by-minute emissions were estimated. Annual emission totals for merchant ships were estimated as 605,000 tons for NOX; 495,000 tons for SO2; 25,600 tons for HC; 53,300 tons for PM and 29,630,000 tons for CO2. This paper presents the methodology and the findings of the emissions estimates for ships. The results will also be compared to satellite observations. For this purpose, CO measurements from MOPITT and SO2 measurements from OMI will be utilized.

46 CFR 113.30-3 - Means of communications.

Code of Federal Regulations, 2010 CFR

2010-10-01

... equipment; and (2) Provide common talking means of two-way voice communication and calling among the... positions listed in § 113.30-5. (b) The means of communication and calling must be a reliable means of voice... 46 Shipping 4 2010-10-01 2010-10-01 false Means of communications. 113.30-3 Section 113.30-3...

Undergraduate courses for enhancing design ability in naval architecture

NASA Astrophysics Data System (ADS)

Lee, Kyu-Yeul; Ku, Namkug; Cha, Ju-Hwan

2013-09-01

Contemporary lectures in undergraduate engineering courses typically focus on teaching major technical knowledge-based theories in a limited time. Therefore, most lectures do not allow the students to gain understanding of how the theories are applied, especially in Naval Architecture and Ocean Engineering departments. Shipyards require students to acquire practical ship design skills in undergraduate courses. To meet this requirement, two lectures are organized by the authors; namely, "Planning Procedure of Naval Architecture & Ocean Engineering" (PNAOE) and "Innovative Ship Design" (ISD). The concept of project-based and collaborative learning is applied in these two lectures. In the PNAOE lecture, sophomores receive instruction in the designing and building of model ships, and the students' work is evaluated in a model ship contest. This curriculum enables students to understand the concepts of ship design and production. In the ISD lecture, seniors learn how to develop their creative ideas about ship design and communicate with members of group. They are encouraged to cooperate with others and understand the ship design process. In the capstone design course, students receive guidance to facilitate understanding of how the knowledge from their sophomore or junior classes, such as fluid mechanics, statics, and dynamics, can be applied to practical ship design. Students are also encouraged to compete in the ship design contest organized by the Society of Naval Architects of Korea. Moreover, the effectiveness of project-based and collaborative learning for enhancing interest in the shipbuilding Industry and understanding the ship design process is demonstrated by citing the PNAOE and ISD lectures as examples.

Update on emissions and environmental impacts from the international fleet of ships: the contribution from major ship types and ports

NASA Astrophysics Data System (ADS)

Dalsøren, S. B.; Eide, M. S.; Endresen, Ø.; Mjelde, A.; Gravir, G.; Isaksen, I. S. A.

2009-03-01

A reliable and up-to-date ship emission inventory is essential for atmospheric scientists quantifying the impact of shipping and for policy makers implementing regulations and incentives for emission reduction. The emission modelling in this study takes into account ship type and size dependent input data for 15 ship types and 7 size categories. Global port arrival and departure data for more than 32 000 merchant ships are used to establish operational profiles for the ship segments. The modelled total fuel consumption amounts to 217 Mt in 2004 of which 11 Mt is consumed in in-port operations. This is in agreement with international sales statistics. The modelled fuel consumption is applied to develop global emission inventories for CO2, NO2, SO2, CO, CH4, VOC (Volatile Organic Compounds), N2O, BC (Black Carbon) and OC (Organic Carbon). The global emissions from ships at sea and in ports are distributed geographically, applying extended geographical data sets covering about 2 million global ship observations and global port data for 32 000 ships. In addition to inventories for the world fleet, inventories are produced separately for the three dominating ship types, using ship type specific emission modelling and traffic distributions. A global Chemical Transport Model (CTM) was used to calculate the environmental impacts of the emissions. We find that ship emissions is a dominant contributor over much of the world oceans to surface concentrations of NO2 and SO2. The contribution is also large over some coastal zones. For surface ozone the contribution is high over the oceans but clearly also of importance over Western North America (contribution 15-25%) and Western Europe (5-15%). The contribution to tropospheric column ozone is up to 5-6%. The overall impact of ship emissions on global methane lifetime is large due to the high NOx emissions. With regard to acidification we find that ships contribute 11% to nitrate wet deposition and 4.5% to sulphur wet deposition globally. In certain coastal regions the contributions may be in the range 15-50%. In general we find that ship emissions have a large impact on acidic deposition and surface ozone in Western North America, Scandinavia, Western Europe, western North Africa and Malaysia/Indonesia. For most of these regions container traffic, the largest emitter by ship type, has the largest impact. This is the case especially for the Pacific and the related container trade routes between Asia and North America. However, the contributions from bulk ships and tank vessels are also significant in the above mentioned impact regions. Though the total ship impact at low latitudes is lower, the tank vessels have a quite large contribution at low latitudes and near the Gulf of Mexico and Middle East. The bulk ships are characterized by large impact in Oceania compared to other ship types. In Scandinavia and north-Western Europe, one of the major ship impact regions, the three largest ship types have rather small relative contributions. The impact in this region is probably dominated by smaller ships operating closer to the coast. For emissions in ports impacts on NO2 and SO2 seem to be of significance. For most ports the contribution to the two components is in the range 0.5-5%, for a few ports it exceeds 10%. The approach presented provides an improvement in characterizing fleet operational patterns, and thereby ship emissions and impacts. Furthermore, the study shows where emission reductions can be applied to most effectively minimize the impacts by different ship types.

Update on emissions and environmental impacts from the international fleet of ships. The contribution from major ship types and ports

NASA Astrophysics Data System (ADS)

Dalsøren, S. B.; Eide, M. S.; Endresen, Ø.; Mjelde, A.; Gravir, G.; Isaksen, I. S. A.

2008-10-01

A reliable and up-to-date ship emission inventory is essential for atmospheric scientists quantifying the impact of shipping and for policy makers implementing regulations and incentives for emission reduction. The emission modelling in this study takes into account ship type and size dependent input data for 15 ship types and 7 size categories. Global port arrival and departure data for more than 32 000 merchant ships are used to establish operational profiles for the ship segments. The modelled total fuel consumption amounts to 217 Mt in 2004 of which 11 Mt is consumed in in-port operations. This is in agreement with international sales statistics. The modelled fuel consumption is applied to develop global emission inventories for CO2, NO2, SO2, CO, CH4, VOC (Volatile Organic Compounds), N2O, BC (Black Carbon) and OC (Organic Carbon). The global emissions from ships at sea and in ports are distributed geographically, applying extended geographical data sets covering about 2 million global ship observations and global port data for 32 000 ships. In addition to inventories for the world fleet, inventories are produced separately for the three dominating ship types, using ship type specific emission modelling and traffic distributions. A global Chemical Transport Model (CTM) was used to calculate the environmental impacts of the emissions. We find that ship emissions is a dominant contributor over much of the world oceans to surface concentrations of NO2 and SO2. The contribution is also large over some coastal zones. For surface ozone the contribution is high over the oceans but clearly also of importance over western North America (contribution 15 25%) and western Europe (5 15%). The contribution to tropospheric column ozone is up to 5 6%. The overall impact of ship emissions on global methane lifetime is large due to the high NOx emissions. With regard to acidification we find that ships contribute 11% to nitrate wet deposition and 4.5% to sulphur wet deposition globally. In certain coastal regions the contributions may be in the range 15 50%. In general we find that ship emissions have a large impact on acidic deposition and surface ozone in western North America, Scandinavia, western Europe, western North Africa and Malaysia/Indonesia. For most of these regions container traffic, the largest emitter by ship type, has the largest impact. This is the case especially for the Pacific and the related container trade routes between Asia and North America. However, the contributions from bulk ships and tank vessels are also significant in the above mentioned impact regions. Though the total ship impact at low latitudes is lower, the tank vessels have a quite large contribution at low latitudes and near the Gulf of Mexico and Middle East. The bulk ships are characterized by large impact in Oceania compared to other ship types. In Scandinavia and north-western Europe, one of the major ship impact regions, the three largest ship types have rather small relative contributions. The impact in this region is probably dominated by smaller ships operating closer to the coast. For emissions in ports impacts on NO2 and SO2 seem to be of significance. For most ports the contribution to the two components is in the range 0.5 5%, for a few ports it exceeds 10%. The approach presented provides an improvement in characterizing fleet operational patterns, and thereby ship emissions and impacts. Furthermore, the study shows where emission reductions can be applied to most effectively minimize the impacts by different ship types.

Ship Detection in Optical Satellite Image Based on RX Method and PCAnet

NASA Astrophysics Data System (ADS)

Shao, Xiu; Li, Huali; Lin, Hui; Kang, Xudong; Lu, Ting

2017-12-01

In this paper, we present a novel method for ship detection in optical satellite image based on the ReedXiaoli (RX) method and the principal component analysis network (PCAnet). The proposed method consists of the following three steps. First, the spatially adjacent pixels in optical image are arranged into a vector, transforming the optical image into a 3D cube image. By taking this process, the contextual information of the spatially adjacent pixels can be integrated to magnify the discrimination between ship and background. Second, the RX anomaly detection method is adopted to preliminarily extract ship candidates from the produced 3D cube image. Finally, real ships are further confirmed among ship candidates by applying the PCAnet and the support vector machine (SVM). Specifically, the PCAnet is a simple deep learning network which is exploited to perform feature extraction, and the SVM is applied to achieve feature pooling and decision making. Experimental results demonstrate that our approach is effective in discriminating between ships and false alarms, and has a good ship detection performance.

A Geographic Optimization Approach to Coast Guard Ship Basing

DTIC Science & Technology

2015-06-01

information found an optimal result for partition- ing. Carlsson applies the travelling salesman problem (tries to find the shortest path to visit a list of...maximum 200 words) This thesis studies the problem of finding efficient ship base locations, area of operations (AO) among bases, and ship assignments...for a coast guard (CG) organization. This problem is faced by many CGs around the world and is motivated by the need to optimize operational outcomes

Hydrographic Data Curation and Stewardship: GO-SHIP

NASA Astrophysics Data System (ADS)

Stephen, Diggs; Lynne, Talley; Martin, Kramp; Bernadette, Sloyan

2014-05-01

Expert data management (access, formats, data life-cycle) facilitates the successful re-use of information which address many important scientific questions such as detecting decadal and longer-term changes in global ocean heat and freshwater content. Modern hydrographic data management has its origins in the WOCE program where new and existing distributed resources were identified and organized into an effective "super DAC". Data from this program are referenced in hundreds of scientific papers. The distributed hydrographic data system, now under the name GO-SHIP, exists today and has adapted to the new geoscience demands of the 21st century. This presentation will describe science drivers and the required data center resources (CCHDO, CDIAC, JCOMMOPS) which together provide reliable access for the global research community.

Simulation Study on the Deflection Response of the 921A Steel thin plate under Explosive Impact Load

NASA Astrophysics Data System (ADS)

Zhang, Yu-Xiang; Chen, Fang; Han, Yan

2018-03-01

The Ship cabin would be subject to high-intensity shock wave load when it is attacked by anti-ship weapons, causing its side board damaged. The time course of the deflection of the thin plate made of 921A steel in different initial conditions under the impact load is researched by theoretical analysis and numerical simulation. According to the theory of elastic-plastic deformation of the thin plate, the dynamic response equation of the thin plate under the explosion impact load is established with the method of energy, and the theoretical calculation value is compared with the result from the simulation method. It proved that the theoretical calculation method has better reliability and accuracy in different boundary size.

A probabilistic model for accidental cargo oil outflow from product tankers in a ship-ship collision.

PubMed

Goerlandt, Floris; Montewka, Jakub

2014-02-15

In risk assessment of maritime transportation, estimation of accidental oil outflow from tankers is important for assessing environmental impacts. However, there typically is limited data concerning the specific structural design and tank arrangement of ships operating in a given area. Moreover, there is uncertainty about the accident scenarios potentially emerging from ship encounters. This paper proposes a Bayesian network (BN) model for reasoning under uncertainty for the assessment of accidental cargo oil outflow in a ship-ship collision where a product tanker is struck. The BN combines a model linking impact scenarios to damage extent with a model for estimating the tank layouts based on limited information regarding the ship. The methodology for constructing the model is presented and output for two accident scenarios is shown. The discussion elaborates on the issue of model validation, both in terms of the BN and in light of the adopted uncertainty/bias-based risk perspective. Copyright © 2013 The Authors. Published by Elsevier Ltd.. All rights reserved.

Lift-based up-ender and methods using same to manipulate a shipping container containing unirradiated nuclear fuel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nilles, Michael J.

A shipping container containing an unirradiated nuclear fuel assembly is lifted off the ground by operating a crane to raise a lifting tool comprising a winch. The lifting tool is connected with the shipping container by a rigging line connecting with the shipping container at a lifting point located on the shipping container between the top and bottom of the shipping container, and by winch cabling connecting with the shipping container at the top of the shipping container. The shipping container is reoriented by operating the winch to adjust the length of the winch cabling so as to rotate themore » shipping container about the lifting point. Shortening the winch cabling rotates the shipping container about the lifting point from a horizontal orientation to a vertical orientation, while lengthening the winch cabling rotates the shipping container about the lifting point from the vertical orientation to the horizontal orientation.« less

Business of reliability

NASA Astrophysics Data System (ADS)

Engel, Pierre

1999-12-01

The presentation is organized around three themes: (1) The decrease of reception equipment costs allows non-Remote Sensing organization to access a technology until recently reserved to scientific elite. What this means is the rise of 'operational' executive agencies considering space-based technology and operations as a viable input to their daily tasks. This is possible thanks to totally dedicated ground receiving entities focusing on one application for themselves, rather than serving a vast community of users. (2) The multiplication of earth observation platforms will form the base for reliable technical and financial solutions. One obstacle to the growth of the earth observation industry is the variety of policies (commercial versus non-commercial) ruling the distribution of the data and value-added products. In particular, the high volume of data sales required for the return on investment does conflict with traditional low-volume data use for most applications. Constant access to data sources supposes monitoring needs as well as technical proficiency. (3) Large volume use of data coupled with low- cost equipment costs is only possible when the technology has proven reliable, in terms of application results, financial risks and data supply. Each of these factors is reviewed. The expectation is that international cooperation between agencies and private ventures will pave the way for future business models. As an illustration, the presentation proposes to use some recent non-traditional monitoring applications, that may lead to significant use of earth observation data, value added products and services: flood monitoring, ship detection, marine oil pollution deterrent systems and rice acreage monitoring.

View southsouthwest of drydock no. 2 caisson with receiving ship ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View south-southwest of drydock no. 2 caisson with receiving ship and ship FS 2 in background. - Naval Base Philadelphia-Philadelphia Naval Shipyard, Drydock No. 2, League Island, Philadelphia, Philadelphia County, PA

Assessment of destabilizing factor for automatic control systems in propulsion systems of mechatronic and maritime transport objects

NASA Astrophysics Data System (ADS)

Zhilenkov, A. A.; Kapitonov, A. A.

2017-10-01

It is known that many of today’s ships and vessels have a shaft generator as a part of their power plants. Modern automatic control systems used in the world’s fleet do not enable their shaft generators to operate in parallel with the main diesel generators for long-term sustenance of the total load of the ship network. On the other hand, according to our calculations and experiments, a shaft generator operated in parallel with the main power plant helps save at least 10% of fuel while making the power system of the ship more efficient, reliable, and eco-friendly. The fouling and corrosion of the propeller as well as the weather conditions of navigation affect its modulus of resistance. It changes the free component of the transient process of shaft generator stress frequency changes in transient processes. While the shaft generator and the diesel generator of the ship power plant are paralleled, there emerges an angle between their EMF. This results in equalizing currents generated between them. The altering torque in the drive-shaft line—propeller system causes torsional fluctuations of the ship shaft line. To compensate for the effect of destabilizing factors and torsional fluctuations of the shaft line on the dynamic characteristics of the transient process that alters the RPM of the main engine, sliding mode controls can be used. To synthesize such a control, one has to evaluate the effect of destabilizing factors.

Development of ship structure health monitoring system based on IOT technology

NASA Astrophysics Data System (ADS)

Yang, Sujun; Shi, Lei; Chen, Demin; Dong, Yuqing; Hu, Zhenyi

2017-06-01

It is very important to monitor the ship structure, because ships are affected by all kinds of wind wave and current environment factor. At the same time, internet of things (IOT) technology plays more and more important role of in the development of industrial process. In the paper, real-time online monitoring of the ship can be realized by means of IOT technology. Ship stress, vibration and dynamic parameters are measured. Meanwhile, data is transmitted to remote monitoring system through intelligent data gateway. Timely remote support can be realized for dangerous stage of ship. Safe navigation of ships is guaranteed through application of the system.

77 FR 39679 - Request for Public Comments on Shipping Tolerances for Export Licenses Issued by the Bureau of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-05

... the applicable ``unit,'' BIS allows either no shipping tolerance on dollar value, or up to 25 percent shipping tolerance on dollar value. The Department of State, which issues licenses for commodities identified on the USML, measures shipping tolerances based on dollar value. The Department of State applies a...

26 CFR 1.954-6 - Foreign base company shipping income.

Code of Federal Regulations, 2014 CFR

2014-04-01

... trawler, a factory ship, and an oil drilling ship are not considered to be used in foreign commerce. On...-term bareboat charter to foreign corporation F for use in foreign commerce. F produces oil in a foreign country and ships the oil to other foreign countries and to the United States. The vessel, when not...

26 CFR 1.954-7 - Increase in qualified investments in foreign base company shipping operations.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Marine insurance claims receivables 1,000 Foreign income tax refunds receivable 1,000 Prepaid shipping expenses and shipping inventories ashore 1,000 Vessel construction funds 0 Vessels 123,000 Vessel plans and construction in progress 3,000 Containers and chassis 0 Terminal property and equipment 2,000 Shipping office...

An AIS-based high-resolution ship emission inventory and its uncertainty in Pearl River Delta region, China.

PubMed

Li, Cheng; Yuan, Zibing; Ou, Jiamin; Fan, Xiaoli; Ye, Siqi; Xiao, Teng; Shi, Yuqi; Huang, Zhijiong; Ng, Simon K W; Zhong, Zhuangmin; Zheng, Junyu

2016-12-15

Ship emissions contribute significantly to air pollution and impose health risks to residents along the coastal area. By using the refined data from the Automatic Identification System (AIS), this study developed a highly resolved ship emission inventory for the Pearl River Delta (PRD) region, China, home to three of ten busiest ports in the world. The region-wide SO 2 , NO X , CO, PM 10 , PM 2.5 , and VOC emissions in 2013 were estimated to be 61,484, 103,717, 10,599, 7155, 6605, and 4195t, respectively. Ocean going vessels were the largest contributors of the total emissions, followed by coastal vessels and river vessels. In terms of ship type, container ship was the leading contributor, followed by conventional cargo ship, dry bulk carrier, fishing ship, and oil tanker. These five ship types accounted for >90% of total emissions. The spatial distributions of emissions revealed that the key emission hot spots all concentrated within the newly proposed emission control area (ECA) and ship emissions within ECA covered >80% of total ship emissions in the PRD, highlighting the importance of ECA in emissions reduction in the PRD. The uncertainties of emission estimates of pollutants were quantified, with lower bounds of -24.5% to -21.2% and upper bounds of 28.6% to 33.3% at 95% confidence intervals. The lower uncertainties in this study highlighted the powerfulness of AIS data in improving ship emission estimates. The AIS-based bottom-up methodology can be used for developing and upgrading ship emission inventory and formulating effective control measures on ship emissions in other port regions wherever possible. Copyright © 2016 Elsevier B.V. All rights reserved.

Maritime User Requirements at High Latitudes - the MARENOR Project

NASA Astrophysics Data System (ADS)

Behlke, R.

2014-12-01

The ionosphere at high latitudes is characterised by a great variety of spatial and temporal variations that influence radio signals. In addition to navigation solutions that are based on Global Navigation Satellite Systems (GNSS), satellite communication systems also suffer from ionospheric degradation. This is worsened by harsh weather conditions, insufficient coverage by geostationary satellites and the absence of land-based augmentation infrastructure. Climate change will lead to a decrease in sea ice extent and thus to an increased use of trans-polar shipping routes, presence of gas and oil industries in the High Arctic and higher focus on Search-and-Rescue (SAR) as well as sovereignty issues. These moments usually require navigation and communication solutions that are accurate and reliable. We describe requirements presented by industrial operators on and around Svalbard. In addition, we present the MARENOR project that aims on evaluating navigation and communication systems at high latitudes including first results

Analysis of radiation exposure for naval units of Operation Crossroads. Volume 3. (Appendix B) support ships. Technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weitz, R.; Thomas, C.; Klemm, J.

1982-03-03

External radiation doses are reconstructed for crews of support and target ships of Joint Task Force One at Operation CROSSROADS, 1946. Volume I describes the reconstruction methodology, which consists of modeling the radiation environment, to include the radioactivity of lagoon water, target ships, and support ship contamination; retracing ship paths through this environment; and calculating the doses to shipboard personnel. The USS RECLAIMER, a support ship, is selected as a representative ship to demonstrate this methodology. Doses for all other ships are summarized. Volume II (Appendix A) details the results for target ship personnel. Volume III (Appendix B) details themore » results for support ship personnel. Calculated doses for more than 36,000 personnel aboard support ships while at Bikini range from zero to 1.7 rem. Of those approximately 34,000 are less than 0.5 rem. From the models provided, doses due to target ship reboarding and doses accrued after departure from Bikini can be calculated, based on the individual circumstances of exposure.« less

Analysis of radiation exposure for naval units of Operation Crossroads. Volume 2. (Appendix A) target ships. Technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weitz, R.; Thomas, C.; Klemm, J.

1982-03-03

External radiation doses are reconstructed for crews of support and target ships of Joint Task Force One at Operation CROSSROADS, 1946. Volume I describes the reconstruction methodology, which consists of modeling the radiation environment, to include the radioactivity of lagoon water, target ships, and support ship contamination; retracing ship paths through this environment; and calculating the doses to shipboard personnel. The USS RECLAIMER, a support ship, is selected as a representative ship to demonstrate this methodology. Doses for all other ships are summarized. Volume II (Appendix A) details the results for target ship personnel. Volume III (Appendix B) details themore » results for support ship personnel. Calculated doses for more than 36,000 personnel aboard support ships while at Bikini range from zero to 1.7 rem. Of those, approximately 34,000 are less than 0.5 rem. From the models provided, doses due to target ship reboarding and doses accrued after departure from Bikini can be calculated, based on the individual circumstances of exposure.« less

DEMONSTRATION OF EQUIVALENCY OF CANE AND SOFTWOOD BASED CELOTEX FOR MODEL 9975 SHIPPING PACKAGES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Watkins, R; Jason Varble, J

2008-05-27

Cane-based Celotex{trademark} has been used extensively in various Department of Energy (DOE) packages as a thermal insulator and impact absorber. Cane-based Celotex{trademark} fiberboard was only manufactured by Knight-Celotex Fiberboard at their Marrero Plant in Louisiana. However, Knight-Celotex Fiberboard shut down their Marrero Plant in early 2007 due to impacts from hurricane Katrina and other economic factors. Therefore, cane-based Celotex{trademark} fiberboard is no longer available for use in the manufacture of new shipping packages requiring the material as a component. Current consolidation plans for the DOE Complex require the procurement of several thousand new Model 9975 shipping packages requiring cane-based Celotex{trademark}more » fiberboard. Therefore, an alternative to cane-based Celotex{trademark} fiberboard is needed. Knight-Celotex currently manufactures Celotex{trademark} fiberboard from other cellulosic materials, such as hardwood and softwood. A review of the relevant literature has shown that softwood-based Celotex{trademark} meets all parameters important to the Model 9975 shipping package.« less

Aerosol and cloud microphysics covariability in the northeast Pacific boundary layer estimated with ship-based and satellite remote sensing observations: NE Pacific Aerosol-Cloud Interactions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Painemal, David; Chiu, J. -Y. Christine; Minnis, Patrick

Ship measurements collected over the northeast Pacific along transects between the port of Los Angeles (33.7°N, 118.2°W) and Honolulu (21.3°N, 157.8°W) during May to August 2013 were utilized to investigate the covariability between marine low cloud microphysical and aerosol properties. Ship-based retrievals of cloud optical depth (τ) from a Sun photometer and liquid water path (LWP) from a microwave radiometer were combined to derive cloud droplet number concentration Nd and compute a cloud-aerosol interaction (ACI) metric defined as ACICCN = ∂ ln(Nd)/∂ ln(CCN), with CCN denoting the cloud condensation nuclei concentration measured at 0.4% (CCN0.4) and 0.3% (CCN0.3) supersaturation. Analysismore » of CCN0.4, accumulation mode aerosol concentration (Na), and extinction coefficient (σext) indicates that Na and σext can be used as CCN0.4 proxies for estimating ACI. ACICCN derived from 10 min averaged Nd and CCN0.4 and CCN0.3, and CCN0.4 regressions using Na and σext, produce high ACICCN: near 1.0, that is, a fractional change in aerosols is associated with an equivalent fractional change in Nd. ACICCN computed in deep boundary layers was small (ACICCN = 0.60), indicating that surface aerosol measurements inadequately represent the aerosol variability below clouds. Satellite cloud retrievals from MODerate-resolution Imaging Spectroradiometer and GOES-15 data were compared against ship-based retrievals and further analyzed to compute a satellite-based ACICCN. Satellite data correlated well with their ship-based counterparts with linear correlation coefficients equal to or greater than 0.78. Combined satellite Nd and ship-based CCN0.4 and Na yielded a maximum ACICCN = 0.88–0.92, a value slightly less than the ship-based ACICCN, but still consistent with aircraft-based studies in the eastern Pacific.« less

Maritime Pre-Positioning Force-Future: Bill Payer or Sea Basing Enabler?

DTIC Science & Technology

2008-03-25

Ship Building Plan , UAV CLASSIFICATION: Unclassified Actions at sea no longer suffice to influence world events; actions from the sea must...in amphibious ships or fall victim to an untenable Navy ship building plan . Premature consideration of cost issues hindered MPF-F program...fiscal environment and an illusory Navy ship building plan . Given the demonstrated capability and success of the current Maritime Pre-positioning

Sea Basing Platforms for the 21st Century - An Evaluation of Maritime Prepositioning Force (Future) [MPF(F)] and the Mobile Offshore Base (MOB) to Perform Sea Basing

DTIC Science & Technology

2004-01-01

Large, Medium Speed , Roll-On/Roll-Off (LMSR) ships . The BLA sea base ships share a common hull, a common propulsion plant, and internal design from...would have the propulsion capable of maintaining a speed of 25 knots. Cargo fuel is stored in either the centerline tanks or in the deep tanks in the...for the Marine Expeditionary Force (Forward) [MEF(FWD)]. The ships required a seaport to offload cargo , an airfield to be the aerial port of

Comparison of chronic disease prevalence between U.S. Navy ships without medical doctors and a similar shore-based population.

PubMed

Hurd, Edward S; Rockswold, Paul D; Westphal, Richard J

2013-05-01

Most U.S. Navy ships operate without embarked physicians, employing Independent Duty Corpsmen to provide primary and emergency medical care to crewmembers. We sought to characterize the burden of chronic disease faced by Independent Duty Corpsmen aboard Navy ships and compare it to that of a similar shore-based population. We conducted cross-sectional analyses of shipboard and shore-based samples using 1,305 records from Norfolk, Virginia-based U.S. Navy ships without doctors between March and May 2007, and records for Norfolk shore-based sailors from the same time frame matched 3:1 on age, sex, and race against the shipboard sample. Asthma prevalence was 2.0% and 5.9% for the shipboard and shore-based samples, respectively (p < 0.0001). Cervical dysplasia among women was 16.2% and 23.1% (p = 0.3687). Depression was 4.6% and 8.4% (p < 0.0001). Diabetes was 1.0% and 2.3% (p = 0.0096). Hyperlipidemia was 20.6% and 21.4% (p = 0.5597). Hypertension was 25.5% and 36.1% (p < 0.0001). Total prevalence for any of the above conditions was 42.5% and 50.9% (p = 0.0001). Over 42% of shipboard sailors have one or more chronic health conditions. Even though the studied conditions were significantly less prevalent aboard ship than in the comparable shore-based sample, nonphysician practitioners aboard ships must be prepared to diagnose and treat chronic diseases. Reprint & Copyright © 2013 Association of Military Surgeons of the U.S.

Marine traffic model based on cellular automaton: Considering the change of the ship's velocity under the influence of the weather and sea

NASA Astrophysics Data System (ADS)

Qi, Le; Zheng, Zhongyi; Gang, Longhui

2017-10-01

It was found that the ships' velocity change, which is impacted by the weather and sea, e.g., wind, sea wave, sea current, tide, etc., is significant and must be considered in the marine traffic model. Therefore, a new marine traffic model based on cellular automaton (CA) was proposed in this paper. The characteristics of the ship's velocity change are taken into account in the model. First, the acceleration of a ship was divided into two components: regular component and random component. Second, the mathematical functions and statistical distribution parameters of the two components were confirmed by spectral analysis, curve fitting and auto-correlation analysis methods. Third, by combining the two components, the acceleration was regenerated in the update rules for ships' movement. To test the performance of the model, the ship traffic flows in the Dover Strait, the Changshan Channel and the Qiongzhou Strait were studied and simulated. The results show that the characteristics of ships' velocities in the simulations are consistent with the measured data by Automatic Identification System (AIS). Although the characteristics of the traffic flow in different areas are different, the velocities of ships can be simulated correctly. It proves that the velocities of ships under the influence of weather and sea can be simulated successfully using the proposed model.

Estimating Ocean Currents from Automatic Identification System Based Ship Drift Measurements

NASA Astrophysics Data System (ADS)

Jakub, Thomas D.

Ship drift is a technique that has been used over the last century and a half to estimate ocean currents. Several of the shortcomings of the ship drift technique include obtaining the data from multiple ships, the time delay in getting those ship positions to a data center for processing and the limited resolution based on the amount of time between position measurements. These shortcomings can be overcome through the use of the Automatic Identification System (AIS). AIS enables more precise ocean current estimates, the option of finer resolution and more timely estimates. In this work, a demonstration of the use of AIS to compute ocean currents is performed. A corresponding error and sensitivity analysis is performed to help identify under which conditions errors will be smaller. A case study in San Francisco Bay with constant AIS message updates was compared against high frequency radar and demonstrated ocean current magnitude residuals of 19 cm/s for ship tracks in a high signal to noise environment. These ship tracks were only minutes long compared to the normally 12 to 24 hour ship tracks. The Gulf of Mexico case study demonstrated the ability to estimate ocean currents over longer baselines and identified the dependency of the estimates on the accuracy of time measurements. Ultimately, AIS measurements when combined with ship drift can provide another method of estimating ocean currents, particularly when other measurements techniques are not available.

Mother ship and physical agents collaboration

NASA Astrophysics Data System (ADS)

Young, Stuart H.; Budulas, Peter P.; Emmerman, Philip J.

1999-07-01

This paper discusses ongoing research at the U.S. Army Research Laboratory that investigates the feasibility of developing a collaboration architecture between small physical agents and a mother ship. This incudes the distribution of planning, perception, mobility, processing and communications requirements between the mother ship and the agents. Small physical agents of the future will be virtually everywhere on the battlefield of the 21st century. A mother ship that is coupled to a team of small collaborating physical agents (conducting tasks such as Reconnaissance, Surveillance, and Target Acquisition (RSTA); logistics; sentry; and communications relay) will be used to build a completely effective and mission capable intelligent system. The mother ship must have long-range mobility to deploy the small, highly maneuverable agents that will operate in urban environments and more localized areas, and act as a logistics base for the smaller agents. The mother ship also establishes a robust communications network between the agents and is the primary information disseminating and receiving point to the external world. Because of its global knowledge and processing power, the mother ship does the high-level control and planning for the collaborative physical agents. This high level control and interaction between the mother ship and its agents (including inter agent collaboration) will be software agent architecture based. The mother ship incorporates multi-resolution battlefield visualization and analysis technology, which aids in mission planning and sensor fusion.

Design and Realization of Ship Fire Simulation Training System Based on Unity3D

NASA Astrophysics Data System (ADS)

Ting, Ye; Feng, Chen; Wenqiang, Wang; Kai, Yang

2018-01-01

Ship fire training is a very important training to ensure the safety of the ship, but limited by the characteristics of the ship itself, it is difficult to carry out fire training on the ship. This paper proposes to introduce a virtual reality technology to build a set of ship fire simulation training system, used to improve the quality of training, reduce training costs. First, the system design ideas are elaborated, and the system architecture diagram is given. Then, the key technologies in the process of system implementation are analyzed. Finally, the system examples are built and tested.

Cloud-based calculators for fast and reliable access to NOAA's geomagnetic field models

NASA Astrophysics Data System (ADS)

Woods, A.; Nair, M. C.; Boneh, N.; Chulliat, A.

2017-12-01

While the Global Positioning System (GPS) provides accurate point locations, it does not provide pointing directions. Therefore, the absolute directional information provided by the Earth's magnetic field is of primary importance for navigation and for the pointing of technical devices such as aircrafts, satellites and lately, mobile phones. The major magnetic sources that affect compass-based navigation are the Earth's core, its magnetized crust and the electric currents in the ionosphere and magnetosphere. NOAA/CIRES Geomagnetism (ngdc.noaa.gov/geomag/) group develops and distributes models that describe all these important sources to aid navigation. Our geomagnetic models are used in variety of platforms including airplanes, ships, submarines and smartphones. While the magnetic field from Earth's core can be described in relatively fewer parameters and is suitable for offline computation, the magnetic sources from Earth's crust, ionosphere and magnetosphere require either significant computational resources or real-time capabilities and are not suitable for offline calculation. This is especially important for small navigational devices or embedded systems, where computational resources are limited. Recognizing the need for a fast and reliable access to our geomagnetic field models, we developed cloud-based application program interfaces (APIs) for NOAA's ionospheric and magnetospheric magnetic field models. In this paper we will describe the need for reliable magnetic calculators, the challenges faced in running geomagnetic field models in the cloud in real-time and the feedback from our user community. We discuss lessons learned harvesting and validating the data which powers our cloud services, as well as our strategies for maintaining near real-time service, including load-balancing, real-time monitoring, and instance cloning. We will also briefly talk about the progress we achieved on NOAA's Big Earth Data Initiative (BEDI) funded project to develop API interface to our Enhanced Magnetic Model (EMM).

The ship edge feature detection based on high and low threshold for remote sensing image

NASA Astrophysics Data System (ADS)

Li, Xuan; Li, Shengyang

2018-05-01

In this paper, a method based on high and low threshold is proposed to detect the ship edge feature due to the low accuracy rate caused by the noise. Analyze the relationship between human vision system and the target features, and to determine the ship target by detecting the edge feature. Firstly, using the second-order differential method to enhance the quality of image; Secondly, to improvement the edge operator, we introduction of high and low threshold contrast to enhancement image edge and non-edge points, and the edge as the foreground image, non-edge as a background image using image segmentation to achieve edge detection, and remove the false edges; Finally, the edge features are described based on the result of edge features detection, and determine the ship target. The experimental results show that the proposed method can effectively reduce the number of false edges in edge detection, and has the high accuracy of remote sensing ship edge detection.

Assessment of Personality as a Requirement for Next Generation Ship Optimal Manning

DTIC Science & Technology

2012-09-01

Department of Test and Evaluation FFG Frigate Guided Missile FFM Five Factor Model FY HRO Fiscal Year High Reliability Organization HSI Human... FFM ) to classify personality and their associated scales provided a renewed foundation for personality trait research (Digman, 1990). Costa and...McCrae’s (1992) FFM of personality traits (openness, conscientiousness, extraversion, agreeableness, and emotional stability) has developed into the

Powering the Nuclear Navy (U.S. Department of Energy)

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

Secretary Perry toured the USS Harry Truman with Admiral Caldwell. The Truman is powered by the Department of Energy’s Nuclear Propulsion Program. These ships can run 25 years with a single nuclear-powered reactor. Secretary Perry was briefed on the importance of nuclear propulsion to the carrier’s capabilities. The Naval Nuclear Propulsion Program provides power plants that ensure safety, reliability, and extended deployment capacity.

How propeller suction is the dominant factor for ship accidents at shallow water conditions

NASA Astrophysics Data System (ADS)

Acar, Dursun; Alpar, Bedri; Ozeren, Sinan

2017-04-01

The laminar flow comes to the fore with the disappearance of the several other directions in the internal displacements in the water current. Due to the dominant speed direction during the straightforward motion of the ship, the underwater hull is associated with the continuous flow of laminar currents. The open marine environment acts as a compressible liquid medium because of the presence of many variables about water volume overflow boundaries where the ship is associated. Layers of water rising over the sea surface due to ship's body and the propeller's water push provides loss of liquid lifting force for the ship. These situations change the well-known sea-floor morphology and reliable depth limits, and lead to probable accidents. If the ship block coefficient for the front side is 0.7 or higher, the "squat" will be more on the bow, because the associated factor "displacement volume" causes to the low-pressure environment due to large and rapid turbulence. Thus, the bow sinks further, which faced with liquid's weaker lift force. The vessels Gerardus Mercator, Queen Elizabeth and Costa Concordia had accidents because of unified reasons of squat, fast water mass displacement by hull push and propeller suction interaction. In the case of water mass displacement from the bow side away, that accident occurred in 2005 by the vessel Gerardus Mercator with excessive longitudinal trim angularity in the shallow water. The vessel Costa Concordia (2012), voluminous water displaced from the rear left side was an important factor because of the sharp manoeuvre of that the captain made before the accident. Observations before the accident indicate that full-speed sharp turn provided listed position for the ship from left (port side) in the direction of travel before colliding and then strike a rock on the sloping side of the seabed. The reason why the ship drifted to the left depends mainly the water discharge occurred at the left side of the hull during left-hand rudder control. Additionally the second water drainage from the shallow ridge area by the propeller's left-directed suction created a shallower environment. Similar situation for example collision of two ships during their side by side forward motions; their positions will be approached and listed to each other more same as downslope movement because of the shared area's water level collapse occur more by two propeller's suction.

Automatic recognition of ship types from infrared images using superstructure moment invariants

NASA Astrophysics Data System (ADS)

Li, Heng; Wang, Xinyu

2007-11-01

Automatic object recognition is an active area of interest for military and commercial applications. In this paper, a system addressing autonomous recognition of ship types in infrared images is proposed. Firstly, an approach of segmentation based on detection of salient features of the target with subsequent shadow removing is proposed, as is the base of the subsequent object recognition. Considering the differences between the shapes of various ships mainly lie in their superstructures, we then use superstructure moment functions invariant to translation, rotation and scale differences in input patterns and develop a robust algorithm of obtaining ship superstructure. Subsequently a back-propagation neural network is used as a classifier in the recognition stage and projection images of simulated three-dimensional ship models are used as the training sets. Our recognition model was implemented and experimentally validated using both simulated three-dimensional ship model images and real images derived from video of an AN/AAS-44V Forward Looking Infrared(FLIR) sensor.

Nonlinear ship waves and computational fluid dynamics

PubMed Central

MIYATA, Hideaki; ORIHARA, Hideo; SATO, Yohei

2014-01-01

Research works undertaken in the first author’s laboratory at the University of Tokyo over the past 30 years are highlighted. Finding of the occurrence of nonlinear waves (named Free-Surface Shock Waves) in the vicinity of a ship advancing at constant speed provided the start-line for the progress of innovative technologies in the ship hull-form design. Based on these findings, a multitude of the Computational Fluid Dynamic (CFD) techniques have been developed over this period, and are highlighted in this paper. The TUMMAC code has been developed for wave problems, based on a rectangular grid system, while the WISDAM code treats both wave and viscous flow problems in the framework of a boundary-fitted grid system. These two techniques are able to cope with almost all fluid dynamical problems relating to ships, including the resistance, ship’s motion and ride-comfort issues. Consequently, the two codes have contributed significantly to the progress in the technology of ship design, and now form an integral part of the ship-designing process. PMID:25311139

Analysis of munitions constituents in groundwater using a field-portable GC-MS.

PubMed

Bednar, A J; Russell, A L; Hayes, C A; Jones, W T; Tackett, P; Splichal, D E; Georgian, T; Parker, L V; Kirgan, R A; MacMillan, D K

2012-05-01

The use of munitions constituents (MCs) at military installations can produce soil and groundwater contamination that requires periodic monitoring even after training or manufacturing activities have ceased. Traditional groundwater monitoring methods require large volumes of aqueous samples (e.g., 2-4 L) to be shipped under chain of custody, to fixed laboratories for analysis. The samples must also be packed on ice and shielded from light to minimize degradation that may occur during transport and storage. The laboratory's turn-around time for sample analysis and reporting can be as long as 45 d. This process hinders the reporting of data to customers in a timely manner; yields data that are not necessarily representative of current site conditions owing to the lag time between sample collection and reporting; and incurs significant shipping costs for samples. The current work compares a field portable Gas Chromatograph-Mass Spectrometer (GC-MS) for analysis of MCs on-site with traditional laboratory-based analysis using High Performance Liquid Chromatography with UV absorption detection. The field method provides near real-time (within ~1 h of sampling) concentrations of MCs in groundwater samples. Mass spectrometry provides reliable confirmation of MCs and a means to identify unknown compounds that are potential false positives for methods with UV and other non-selective detectors. Published by Elsevier Ltd.

46 CFR 64.27 - Base.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false Base. 64.27 Section 64.27 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING MARINE PORTABLE TANKS AND CARGO HANDLING SYSTEMS Standards for an MPT § 64.27 Base. The base of an MPT must be as wide and as long as the tank. ...

46 CFR 64.27 - Base.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false Base. 64.27 Section 64.27 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING MARINE PORTABLE TANKS AND CARGO HANDLING SYSTEMS Standards for an MPT § 64.27 Base. The base of an MPT must be as wide and as long as the tank. ...

46 CFR 64.27 - Base.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false Base. 64.27 Section 64.27 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING MARINE PORTABLE TANKS AND CARGO HANDLING SYSTEMS Standards for an MPT § 64.27 Base. The base of an MPT must be as wide and as long as the tank. ...

46 CFR 64.27 - Base.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Base. 64.27 Section 64.27 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING MARINE PORTABLE TANKS AND CARGO HANDLING SYSTEMS Standards for an MPT § 64.27 Base. The base of an MPT must be as wide and as long as the tank. ...

Investigation on coupling error characteristics in angular rate matching based ship deformation measurement approach

NASA Astrophysics Data System (ADS)

Yang, Shuai; Wu, Wei; Wang, Xingshu; Xu, Zhiguang

2018-01-01

The coupling error in the measurement of ship hull deformation can significantly influence the attitude accuracy of the shipborne weapons and equipments. It is therefore important to study the characteristics of the coupling error. In this paper, an comprehensive investigation on the coupling error is reported, which has a potential of deducting the coupling error in the future. Firstly, the causes and characteristics of the coupling error are analyzed theoretically based on the basic theory of measuring ship deformation. Then, simulations are conducted for verifying the correctness of the theoretical analysis. Simulation results show that the cross-correlation between dynamic flexure and ship angular motion leads to the coupling error in measuring ship deformation, and coupling error increases with the correlation value between them. All the simulation results coincide with the theoretical analysis.

Research on theoretical optimization and experimental verification of minimum resistance hull form based on Rankine source method

NASA Astrophysics Data System (ADS)

Zhang, Bao-Ji; Zhang, Zhu-Xin

2015-09-01

To obtain low resistance and high efficiency energy-saving ship, minimum total resistance hull form design method is studied based on potential flow theory of wave-making resistance and considering the effects of tail viscous separation. With the sum of wave resistance and viscous resistance as objective functions and the parameters of B-Spline function as design variables, mathematical models are built using Nonlinear Programming Method (NLP) ensuring the basic limit of displacement and considering rear viscous separation. We develop ship lines optimization procedures with intellectual property rights. Series60 is used as parent ship in optimization design to obtain improved ship (Series60-1) theoretically. Then drag tests for the improved ship (Series60-1) is made to get the actual minimum total resistance hull form.

Observational and Dynamical Wave Climatologies. VOS vs Satellite Data

NASA Astrophysics Data System (ADS)

Grigorieva, Victoria; Badulin, Sergei; Chernyshova, Anna

2013-04-01

The understanding physics of wind-driven waves is crucially important for fundamental science and practical applications. This is why experimental efforts are targeted at both getting reliable information on sea state and elaborating effective tools of the sea wave forecasting. The global Visual Wave Observations and satellite data from the GLOBWAVE project of the European Space Agency are analyzed in the context of these two viewpoints. Within the first "observational" aspect we re-analyze conventional climatologies of all basic wave parameters for the last decades [5]. An alternative "dynamical" climatology is introduced as a tool of prediction of dynamical features of sea waves on global scales. The features of wave dynamics are studied in terms of one-parametric dependencies of wave heights on wave periods following the theoretical concept of self-similar wind-driven seas [3, 1, 4] and recently proposed approach to analysis of Voluntary Observing Ship (VOS) data [2]. Traditional "observational" climatologies based on VOS and satellite data collections demonstrate extremely consistent pictures for significant wave heights and dominant periods. On the other hand, collocated satellite and VOS data show significant differences in wave heights, wind speeds and, especially, in wave periods. Uncertainties of visual wave observations can explain these differences only partially. We see the key reason of this inconsistency in the methods of satellite data processing which are based on formal application of data interpolation methods rather than on up-to-date physics of wind-driven waves. The problem is considered within the alternative climatology approach where dynamical criteria of wave height-to-period linkage are used for retrieving wave periods and constructing physically consistent dynamical climatology. The key dynamical parameter - exponent R of one-parametric dependence Hs ~ TR shows dramatically less pronounced latitudinal dependence as compared to observed Hs and T of conventional climatology in both satellite and VOS data collections. It can be treated as an effect of interaction of wind-driven seas and swell on global scales as it was stated in [2]. Further study combining the alternative and conventional climatologies can help to detail this important dynamical effect of global wave dynamics. The progress in satellite data processing and their physical interpretation is of great value for such study. The work was supported by Russian Foundation for Basic Research grant 11-05-01114-a and the Russian government contracts No.11.G34.31.0035, No.11.G34.31.0078. References [1] S. I. Badulin, A. V. Babanin, D. Resio, and V. Zakharov. Weakly turbulent laws of wind-wave growth. J. Fluid Mech., 591:339-378, 2007. [2] S. I. Badulin and Grigorieva V. G. On discriminating swell and wind-driven seas in voluntary observing ship data. J. Geophys. Res., 117(C00J29), 2012. [3] S. I. Badulin, A. N. Pushkarev, D. Resio, and V. E. Zakharov. Self-similarity of wind-driven seas. Nonl. Proc. Geophys., 12:891-946, 2005. [4] E. Gagnaire-Renou, M. Benoit, and S. I. Badulin. On weakly turbulent scaling of wind sea in simulations of fetch-limited growth. J. Fluid Mech., 669:178-213, 2011. [5] S. K. Gulev, V. Grigorieva, A. Sterl, and D. Woolf. Assessment for the reliability of wave observations from voluntary observing ships: insights from the validation of a global wind wave climatology based on voluntary observing ship data. J. Geophys. Res. - Oceans, 108(C7):3236, doi:10,1029/2002JC001437, 2003.

Multidimensional approach to invasive species prevention.

PubMed

Briski, Elizabeta; Allinger, Lisa E; Balcer, Mary; Cangelosi, Allegra; Fanberg, Lana; Markee, Tom P; Mays, Nicole; Polkinghorne, Christine N; Prihoda, Kelsey R; Reavie, Euan D; Regan, Deanna H; Reid, Donald M; Saillard, Heidi J; Schwerdt, Tyler; Schaefer, Heidi; TenEyck, Matthew; Wiley, Chris J; Bailey, Sarah A

2013-02-05

Nonindigenous species (NIS) cause global biotic homogenization and extinctions, with commercial shipping being a leading vector for spread of aquatic NIS. To reduce transport of NIS by ships, regulations requiring ballast water exchange (BWE) have been implemented by numerous countries. BWE appears to effectively reduce risk for freshwater ports, but provides only moderate protection of marine ports. In the near future, ships may be required to undertake ballast water treatment (BWT) to meet numeric performance standards, and BWE may be phased out of use. However, there are concerns that BWT systems may not operate reliably in fresh or turbid water, or both. Consequently, it has been proposed that BWE could be used in combination with BWT to maximize the positive benefits of both management strategies for protection of freshwater ports. We compared the biological efficacy of "BWE plus BWT" against "BWT alone" at a ballast water treatment experimental test facility. Our comparative evaluation showed that even though BWT alone significantly reduced abundances of all tested organism groups except total heterotrophic bacteria, the BWE plus BWT strategy significantly reduced abundances for all groups and furthermore resulted in significantly lower abundances of most groups when compared to BWT alone. Our study clearly demonstrates potential benefits of combining BWE with BWT to reduce invasion risk of freshwater organisms transported in ships' ballast water, and it should be of interest to policy makers and environmental managers.

Measurement and computer simulation of antennas on ships and aircraft for results of operational reliability

NASA Astrophysics Data System (ADS)

Kubina, Stanley J.

1989-09-01

The review of the status of computational electromagnetics by Miller and the exposition by Burke of the developments in one of the more important computer codes in the application of the electric field integral equation method, the Numerical Electromagnetic Code (NEC), coupled with Molinet's summary of progress in techniques based on the Geometrical Theory of Diffraction (GTD), provide a clear perspective on the maturity of the modern discipline of computational electromagnetics and its potential. Audone's exposition of the application to the computation of Radar Scattering Cross-section (RCS) is an indication of the breadth of practical applications and his exploitation of modern near-field measurement techniques reminds one of progress in the measurement discipline which is essential to the validation or calibration of computational modeling methodology when applied to complex structures such as aircraft and ships. The latter monograph also presents some comparison results with computational models. Some of the results presented for scale model and flight measurements show some serious disagreements in the lobe structure which would require some detailed examination. This also applies to the radiation patterns obtained by flight measurement compared with those obtained using wire-grid models and integral equation modeling methods. In the examples which follow, an attempt is made to match measurements results completely over the entire 2 to 30 MHz HF range for antennas on a large patrol aircraft. The problem of validating computer models of HF antennas on a helicopter and using computer models to generate radiation pattern information which cannot be obtained by measurements are discussed. The use of NEC computer models to analyze top-side ship configurations where measurement results are not available and only self-validation measures are available or at best comparisons with an alternate GTD computer modeling technique is also discussed.

Extended Edited Synoptic Cloud Reports from Ships and Land Stations Over the Globe, 1952-2009 (NDP-026C)

DOE Data Explorer

Hahn, C. J. [University of Arizona; Warren, S. G. [University of Washington; Eastman, R.

1999-08-01

This database contains surface synoptic weather reports for the entire globe, gathered from various available data sets. The reports were processed, edited, and rewritten to provide a single dataset of individual observations of clouds, spanning the 57 years 1952-2008 for ship data and the 39 years 1971-2009 for land station data. In addition to the cloud portion of the synoptic report, each edited report also includes the associated pressure, present weather, wind, air temperature, and dew point (and sea surface temperature over oceans). This data set is called the "Extended Edited Cloud Report Archive" (EECRA). The EECRA is based solely on visual cloud observations from weather stations, reported in the WMO synoptic code (WMO, 1974). Reports must contain cloud-type information to be included in the archive. Past data sources include those from the Fleet Numerical Oceanographic Center (FNOC, 1971-1976) and the National Centers for Environmental Prediction (NCEP, 1977-1996). This update uses data from a new source, the 'Integrated Surface Database' (ISD, 1997-2009; Smith et al., 2011). Our past analyses of the EECRA identified a subset of 5388 weather stations that were determined to produce reliable day and night observations of cloud amount and type. The update contains observations only from this subset of stations. Details concerning processing, previous problems, contents, and comments are available in the archive's original documentation . The EECRA contains about 81 million cloud observations from ships and 380 million from land stations. The data files have been compressed using unix. Unix/linux users can "uncompress" or "gunzip" the files after downloading. If you're interested in the NDP-026C database, then you'll also want to explore its related data products, NDP-026D and NDP-026E.

A cellular automaton model for ship traffic flow in waterways

NASA Astrophysics Data System (ADS)

Qi, Le; Zheng, Zhongyi; Gang, Longhui

2017-04-01

With the development of marine traffic, waterways become congested and more complicated traffic phenomena in ship traffic flow are observed. It is important and necessary to build a ship traffic flow model based on cellular automata (CAs) to study the phenomena and improve marine transportation efficiency and safety. Spatial discretization rules for waterways and update rules for ship movement are two important issues that are very different from vehicle traffic. To solve these issues, a CA model for ship traffic flow, called a spatial-logical mapping (SLM) model, is presented. In this model, the spatial discretization rules are improved by adding a mapping rule. And the dynamic ship domain model is considered in the update rules to describe ships' interaction more exactly. Take the ship traffic flow in the Singapore Strait for example, some simulations were carried out and compared. The simulations show that the SLM model could avoid ship pseudo lane-change efficiently, which is caused by traditional spatial discretization rules. The ship velocity change in the SLM model is consistent with the measured data. At finally, from the fundamental diagram, the relationship between traffic ability and the lengths of ships is explored. The number of ships in the waterway declines when the proportion of large ships increases.

The Cost-Effectiveness of Nuclear Power for Navy Surface Ships

DTIC Science & Technology

2011-05-01

shipbuilding plan. 1 All of the Navy’s aircraft car- riers (and submarines) are powered by nuclear reactors ; its other surface combatants are powered by...in whether the ships were powered by conventional systems that used petroleum-based fuels or by nuclear reactors . Estimates of the relative costs...would existing ships be retrofitted with nuclear reactors . 5. Those fuel -reduction findings are based on CBO’s analysis and on data provided to CBO by

Occurrence of lower cloud albedo in ship tracks

NASA Astrophysics Data System (ADS)

Chen, Y.-C.; Christensen, M. W.; Xue, L.; Sorooshian, A.; Stephens, G. L.; Rasmussen, R. M.; Seinfeld, J. H.

2012-09-01

The concept of geoengineering by marine cloud brightening is based on seeding marine stratocumulus clouds with sub-micrometer sea-salt particles to enhance the cloud droplet number concentration and cloud albedo, thereby producing a climate cooling effect. The efficacy of this as a strategy for global cooling rests on the extent to which aerosol-perturbed marine clouds will respond with increased albedo. Ship tracks, quasi-linear cloud features prevalent in oceanic regions impacted by ship exhaust, are a well-known manifestation of the effect of aerosol injection on marine clouds. We present here an analysis of the albedo responses in ship tracks, based on in situ aircraft measurements and three years of satellite observations of 589 individual ship tracks. It is found that the sign (increase or decrease) and magnitude of the albedo response in ship tracks depends on the mesoscale cloud structure, the free tropospheric humidity, and cloud top height. In a closed cell structure (cloud cells ringed by a perimeter of clear air), nearly 30% of ship tracks exhibited a decreased albedo. Detailed cloud responses must be accounted for in global studies of the potential efficacy of sea-spray geoengineering as a means to counteract global warming.

Disposition of Orange Herbicide by Incineration. Revised Draft Environmental Statement

DTIC Science & Technology

1974-04-01

a ship , the "Vulcanls," has beer equipped to carry certain hazardous liquid chemical cargoes ...dispersed. For this analyses the dispersion zone is based on a one knot wind speed , "crosswind" of the ship’s course, 10 knot speed for the ship during... shipping company; the wind speed and effective mixing height are very con- servative. For such a low wind speed , it is anticipated that the

Inventory Funding Methods on Navy Ships: NWCF vs. End-Use

DTIC Science & Technology

2013-05-30

Category OPTAR Operating Target OSO Other Supply Officer POM Pre/Post-Overseas Movement R-Supply Relational Supply RoR Reorder Review SAC Service... OSO ) transfer. Since end-use ships own their inventory, the supply officer can choose to transfer a part being requested by another ship at their...discretion, based on their ship’s anticipated requirements and their own goodwill. OSO transfers among end-use ships do not require a transfer of OPTAR

Monitoring shipping emissions in the German Bight using MAX-DOAS measurements

NASA Astrophysics Data System (ADS)

Seyler, André; Wittrock, Folkard; Kattner, Lisa; Mathieu-Üffing, Barbara; Peters, Enno; Richter, Andreas; Schmolke, Stefan; Burrows, John P.

2017-04-01

Shipping is generally the most energy efficient transportation mode, but, at the same time, it accounts for four fifths of the worldwide total merchandise trade volume. As a result, shipping contributes a significant part to the emissions from the transportation sector. The majority of shipping emissions occurs within 400 km of land, impacting on air pollution in coastal areas and harbor towns. The North Sea has one of the highest ship densities in the world and the vast majority of ships heading for the port of Hamburg sail through the German Bight and into the river Elbe. A three-year time series of ground-based MAX-DOAS measurements of NO2 and SO2 on the island Neuwerk in the German Bight has been analyzed for contributions from shipping emissions. Measurements of individual ship plumes as well as of background pollution are possible from this location, which is 6-7 kilometers away from the main shipping lane towards the harbor of Hamburg. More than 2000 individual ship plumes have been identified in the data and analyzed for the emission ratio of SO2 to NO2, yielding an average ratio of 0.3 for the years 2013/2014. Contributions of ships and land-based sources to air pollution levels in the German Bight have been estimated, showing that despite the vicinity to the shipping lane, the contribution of shipping sources to air pollution is only about 40%. Since January 2015, much lower fuel sulfur content limits of 0.1% (before: 1.0%) apply in the North and Baltic Sea Emission Control Area (ECA). Comparing MAX-DOAS measurements from 2015/2016 (new regulation) to 2013/2014 (old regulation), a large reduction in SO2/NO2 ratios in shipping emissions and a significant reduction (by a factor of eight) in ambient coastal SO2 levels have been observed. In addition to that, selected shipping emission measurements from other measurement sites and campaigns are presented. This study is part of the project MeSMarT (Measurements of Shipping emissions in the Marine Troposphere), a cooperation between the University of Bremen and the Federal Maritime and Hydrographic Agency (Bundesamt für Seeschifffahrt und Hydrographie, BSH), supported by the Helmholtz Zentrum Geesthacht (HZG).

Study on lockage safety of LNG-fueled ships based on FSA.

PubMed

Lv, Pengfei; Zhuang, Yuan; Deng, Jian; Su, Wei

2017-01-01

In the present study, formal safety assessment (FSA) is introduced to investigate lockage safety of LNG-fueled ships. Risk sources during lockage of LNG-fueled ships in four typical scenarios, namely, navigation between two dams, lockage, anchorage, and fueling, are identified, and studied in combination with fundamental leakage probabilities of various components of LNG storage tanks, and simulation results of accident consequences. Some suggestions for lockage safety management of LNG-fueled ships are then proposed. The present research results have certain practical significance for promoting applications of LNG-fueled ships along Chuanjiang River and in Three Gorges Reservoir Region.

Aerial view of entire LTA base after completion of both ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Aerial view of entire LTA base after completion of both LTA ship hangars. Date unknown but probably circa 1945. - Marine Corps Air Station Tustin, Northern Lighter Than Air Ship Hangar, Meffett Avenue & Maxfield Street, Tustin, Orange County, CA

Multi-position photovoltaic assembly

DOEpatents

Dinwoodie, Thomas L.

2003-03-18

The invention is directed to a PV assembly, for use on a support surface, comprising a base, a PV module, a multi-position module support assembly, securing the module to the base at shipping and inclined-use angles, a deflector, a multi-position deflector support securing the deflector to the base at deflector shipping and deflector inclined-use angles, the module and deflector having opposed edges defining a gap therebetween. The invention permits transport of the PV assemblies in a relatively compact form, thus lowering shipping costs, while facilitating installation of the PV assemblies with the PV module at the proper inclination.

Image-based corrosion recognition for ship steel structures

NASA Astrophysics Data System (ADS)

Ma, Yucong; Yang, Yang; Yao, Yuan; Li, Shengyuan; Zhao, Xuefeng

2018-03-01

Ship structures are subjected to corrosion inevitably in service. Existed image-based methods are influenced by the noises in images because they recognize corrosion by extracting features. In this paper, a novel method of image-based corrosion recognition for ship steel structures is proposed. The method utilizes convolutional neural networks (CNN) and will not be affected by noises in images. A CNN used to recognize corrosion was designed through fine-turning an existing CNN architecture and trained by datasets built using lots of images. Combining the trained CNN classifier with a sliding window technique, the corrosion zone in an image can be recognized.

Ship Detection in SAR Image Based on the Alpha-stable Distribution

PubMed Central

Wang, Changcheng; Liao, Mingsheng; Li, Xiaofeng

2008-01-01

This paper describes an improved Constant False Alarm Rate (CFAR) ship detection algorithm in spaceborne synthetic aperture radar (SAR) image based on Alpha-stable distribution model. Typically, the CFAR algorithm uses the Gaussian distribution model to describe statistical characteristics of a SAR image background clutter. However, the Gaussian distribution is only valid for multilook SAR images when several radar looks are averaged. As sea clutter in SAR images shows spiky or heavy-tailed characteristics, the Gaussian distribution often fails to describe background sea clutter. In this study, we replace the Gaussian distribution with the Alpha-stable distribution, which is widely used in impulsive or spiky signal processing, to describe the background sea clutter in SAR images. In our proposed algorithm, an initial step for detecting possible ship targets is employed. Then, similar to the typical two-parameter CFAR algorithm, a local process is applied to the pixel identified as possible target. A RADARSAT-1 image is used to validate this Alpha-stable distribution based algorithm. Meanwhile, known ship location data during the time of RADARSAT-1 SAR image acquisition is used to validate ship detection results. Validation results show improvements of the new CFAR algorithm based on the Alpha-stable distribution over the CFAR algorithm based on the Gaussian distribution. PMID:27873794

Navy Virginia (SSN-774) Class Attack Submarine Procurement: Background and Issues for Congress

DTIC Science & Technology

2010-07-30

conformal acoustic velocity sensor wide aperture array (CAVES WAA), and a flexible payload sail. AESR is a software package comprised of two systems...when they are modernized. CAVES WAA is a sensor array that is designed to detect the vibrations and acoustic signatures of targets. The Navy has...require reliability improvements (Active Shaft Grounding System, Circuit D, Ship Service Turbine Generator magnetic levitation bearings / throttle

GPHS-RTGs in support of the Cassini Mission

NASA Astrophysics Data System (ADS)

1994-10-01

The progress on the radioisotope generators and ancillary activities is described. This report is organized by program task as follows: spacecraft integration and liaison; engineering support; safety; qualified unicouple fabrication; ETG fabrication, assembly, and test; ground support equipment; RTG shipping and launch support; design, reviews, and mission applications; project management, quality assurance and reliability, contract changes, non-capital CAGO acquisition, and CAGO maintenance; contractor acquired government owned property (CAGO) acquisition.

GPHS-RTGs in support of the Cassini mission

NASA Astrophysics Data System (ADS)

1992-04-01

The technical progress achieved during the period 30 Mar. - 27 Sep. 1992 is described. Topics covered include: spacecraft integration and liaison; engineering support; safety; qualified unicouple production, ETG fabrication, assembly, and test; ground support equipment; radioisotope thermoelectric generators (RTG) shipping and launch support; designs, reviews, and mission applications; project management, quality assurance, reliability, contract changes, non-capital contractor acquired government owned (CAGO) acquisitions, and CAGO maintenance; and CAGO acquisitions.

Automatic Ship Detection in Remote Sensing Images from Google Earth of Complex Scenes Based on Multiscale Rotation Dense Feature Pyramid Networks

NASA Astrophysics Data System (ADS)

Yang, Xue; Sun, Hao; Fu, Kun; Yang, Jirui; Sun, Xian; Yan, Menglong; Guo, Zhi

2018-01-01

Ship detection has been playing a significant role in the field of remote sensing for a long time but it is still full of challenges. The main limitations of traditional ship detection methods usually lie in the complexity of application scenarios, the difficulty of intensive object detection and the redundancy of detection region. In order to solve such problems above, we propose a framework called Rotation Dense Feature Pyramid Networks (R-DFPN) which can effectively detect ship in different scenes including ocean and port. Specifically, we put forward the Dense Feature Pyramid Network (DFPN), which is aimed at solving the problem resulted from the narrow width of the ship. Compared with previous multi-scale detectors such as Feature Pyramid Network (FPN), DFPN builds the high-level semantic feature-maps for all scales by means of dense connections, through which enhances the feature propagation and encourages the feature reuse. Additionally, in the case of ship rotation and dense arrangement, we design a rotation anchor strategy to predict the minimum circumscribed rectangle of the object so as to reduce the redundant detection region and improve the recall. Furthermore, we also propose multi-scale ROI Align for the purpose of maintaining the completeness of semantic and spatial information. Experiments based on remote sensing images from Google Earth for ship detection show that our detection method based on R-DFPN representation has a state-of-the-art performance.

Aerosol and cloud microphysics covariability in the northeast Pacific boundary layer estimated with ship-based and satellite remote sensing observations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Painemal, David; Chiu, J. -Y. Christine; Minnis, Patrick

We utilized ship measurements collected over the northeast Pacific along transects between the port of Los Angeles (33.7°N, 118.2°W) and Honolulu (21.3°N, 157.8°W) during May to August 2013 in order to investigate the covariability between marine low cloud microphysical and aerosol properties. Ship-based retrievals of cloud optical depth (τ) from a Sun photometer and liquid water path (LWP) from a microwave radiometer were combined to derive cloud droplet number concentration N d and compute a cloud-aerosol interaction (ACI) metric defined as ACI CCN=∂ ln(N d)/∂ ln(CCN), with CCN denoting the cloud condensation nuclei concentration measured at 0.4% (CCN 0.4) andmore » 0.3% (CCN 0.3) supersaturation. Analysis of CCN 0.4, accumulation mode aerosol concentration (N a), and extinction coefficient (σ ext) indicates that N a and σ ext can be used as CCN 0.4 proxies for estimating ACI. ACI CCN derived from 10 min averaged N d and CCN 0.4 and CCN 0.3, and CCN 0.4 regressions using N a and σ ext, produce high ACI CCN: near 1.0, that is, a fractional change in aerosols is associated with an equivalent fractional change in Nd. ACI CCN computed in deep boundary layers was small (ACI CCN=0.60), indicating that surface aerosol measurements inadequately represent the aerosol variability below clouds. Satellite cloud retrievals from MODerate-resolution Imaging Spectroradiometer and GOES-15 data were compared against ship-based retrievals and further analyzed to compute a satellite-based ACI CCN. We found that the satellite data correlated well with their ship-based counterparts with linear correlation coefficients equal to or greater than 0.78. Combined satellite Nd and ship-based CCN 0.4 and Na yielded a maximum ACI CCN=0.88–0.92, a value slightly less than the ship-based ACI CCN, but still consistent with aircraft-based studies in the eastern Pacific.« less

Aerosol and cloud microphysics covariability in the northeast Pacific boundary layer estimated with ship-based and satellite remote sensing observations

DOE PAGES

Painemal, David; Chiu, J. -Y. Christine; Minnis, Patrick; ...

2017-02-27

We utilized ship measurements collected over the northeast Pacific along transects between the port of Los Angeles (33.7°N, 118.2°W) and Honolulu (21.3°N, 157.8°W) during May to August 2013 in order to investigate the covariability between marine low cloud microphysical and aerosol properties. Ship-based retrievals of cloud optical depth (τ) from a Sun photometer and liquid water path (LWP) from a microwave radiometer were combined to derive cloud droplet number concentration N d and compute a cloud-aerosol interaction (ACI) metric defined as ACI CCN=∂ ln(N d)/∂ ln(CCN), with CCN denoting the cloud condensation nuclei concentration measured at 0.4% (CCN 0.4) andmore » 0.3% (CCN 0.3) supersaturation. Analysis of CCN 0.4, accumulation mode aerosol concentration (N a), and extinction coefficient (σ ext) indicates that N a and σ ext can be used as CCN 0.4 proxies for estimating ACI. ACI CCN derived from 10 min averaged N d and CCN 0.4 and CCN 0.3, and CCN 0.4 regressions using N a and σ ext, produce high ACI CCN: near 1.0, that is, a fractional change in aerosols is associated with an equivalent fractional change in Nd. ACI CCN computed in deep boundary layers was small (ACI CCN=0.60), indicating that surface aerosol measurements inadequately represent the aerosol variability below clouds. Satellite cloud retrievals from MODerate-resolution Imaging Spectroradiometer and GOES-15 data were compared against ship-based retrievals and further analyzed to compute a satellite-based ACI CCN. We found that the satellite data correlated well with their ship-based counterparts with linear correlation coefficients equal to or greater than 0.78. Combined satellite Nd and ship-based CCN 0.4 and Na yielded a maximum ACI CCN=0.88–0.92, a value slightly less than the ship-based ACI CCN, but still consistent with aircraft-based studies in the eastern Pacific.« less

Laborious and perilous adventures: the triumphant return of Francois Arago to France

NASA Astrophysics Data System (ADS)

Murdin, P.

2005-08-01

As a young man, while measuring the Paris Meridian in the Balearic Islands, the French astronomer Francois Arago was caught up in events of the Peninsular and Napoleonic Wars and found himself under arrest in Algiers. Released from custody and returning from Algiers to Marseille in 1809, he was detained again, this time by the British Royal Navy warship HMS Minstrel, but let go. The Algerian ships with which he was traveling were captured and taken to Gibraltar. The incident caused an abrupt deterioration in Anglo-Algerian relations, which however recovered when Napoleon declared war on Algiers. A comparison of the account in his autobiography with the logs of Royal Navy ships confirms the outline and many details of his account of his arrest but also sheds light on the reliability of his autobiography.

Estimation of the average exchanges in momentum and latent heat between the atmosphere and the oceans with Seasat observations

NASA Technical Reports Server (NTRS)

Liu, W. T.

1983-01-01

Ocean-surface momentum flux and latent heat flux are determined from Seasat-A data from 1978 and compared with ship observations. Momentum flux was measured using the Seasat-A scatterometer system (SASS) heat flux, with the scanning multichannel MW radiometer (SMMR). Ship measurements were quality selected and averaged to increase their reliability. The fluxes were computed using a bulk parameterization technique. It is found that although SASS effectively measures momentum flux, variations in atmospheric stability and sea-surface temperature cause deviations which are not accounted for by the present data-processing algorithm. The SMMR-latent-heat-flux algorithm, while needing refinement, is shown to given estimations to within 35 W/sq m in its present form, which removes systematic error and uses an empirically determined transfer coefficient.

Structural analysis of a ship on global aspect using ANSYS

NASA Astrophysics Data System (ADS)

Rahman, M. Muzibur; Kamol, Rajia Sultana; Islam, Reyana

2017-12-01

Ship is a complex geometry which undergoes a combination of loadings such as hydrostatic, hydrodynamic, wind, wave etc. at sea and thus adequate strength in a ship has always been one of the most challenging tasks for the ship designers. International Maritime Organization (IMO) and classification societies are providing the standards to ensure the adequacy of strength for the ship against all demands throughout its service life. Thus, structural analysis is needed to assess the overall strength of hull, and the means in this regard are based on finite element method which may be applied either local or global aspect of the ship. This paper is an attempt to carry out the structural analysis of a ship in global aspect using ANSYS software to locate the most stress concentration and deformed area, which will have ultimate effect on fatigue fracture.

Strength Analysis on Ship Ladder Using Finite Element Method

NASA Astrophysics Data System (ADS)

Budianto; Wahyudi, M. T.; Dinata, U.; Ruddianto; Eko P., M. M.

2018-01-01

In designing the ship’s structure, it should refer to the rules in accordance with applicable classification standards. In this case, designing Ladder (Staircase) on a Ferry Ship which is set up, it must be reviewed based on the loads during ship operations, either during sailing or at port operations. The classification rules in ship design refer to the calculation of the structure components described in Classification calculation method and can be analysed using the Finite Element Method. Classification Regulations used in the design of Ferry Ships used BKI (Bureau of Classification Indonesia). So the rules for the provision of material composition in the mechanical properties of the material should refer to the classification of the used vessel. The analysis in this structure used program structure packages based on Finite Element Method. By using structural analysis on Ladder (Ladder), it obtained strength and simulation structure that can withstand load 140 kg both in static condition, dynamic, and impact. Therefore, the result of the analysis included values of safety factors in the ship is to keep the structure safe but the strength of the structure is not excessive.

A novel ship CFAR detection algorithm based on adaptive parameter enhancement and wake-aided detection in SAR images

NASA Astrophysics Data System (ADS)

Meng, Siqi; Ren, Kan; Lu, Dongming; Gu, Guohua; Chen, Qian; Lu, Guojun

2018-03-01

Synthetic aperture radar (SAR) is an indispensable and useful method for marine monitoring. With the increase of SAR sensors, high resolution images can be acquired and contain more target structure information, such as more spatial details etc. This paper presents a novel adaptive parameter transform (APT) domain constant false alarm rate (CFAR) to highlight targets. The whole method is based on the APT domain value. Firstly, the image is mapped to the new transform domain by the algorithm. Secondly, the false candidate target pixels are screened out by the CFAR detector to highlight the target ships. Thirdly, the ship pixels are replaced by the homogeneous sea pixels. And then, the enhanced image is processed by Niblack algorithm to obtain the wake binary image. Finally, normalized Hough transform (NHT) is used to detect wakes in the binary image, as a verification of the presence of the ships. Experiments on real SAR images validate that the proposed transform does enhance the target structure and improve the contrast of the image. The algorithm has a good performance in the ship and ship wake detection.

Identifying Modeled Ship Noise Hotspots for Marine Mammals of Canada's Pacific Region

PubMed Central

Erbe, Christine; Williams, Rob; Sandilands, Doug; Ashe, Erin

2014-01-01

The inshore, continental shelf waters of British Columbia (BC), Canada are busy with ship traffic. South coast waters are heavily trafficked by ships using the ports of Vancouver and Seattle. North coast waters are less busy, but expected to get busier based on proposals for container port and liquefied natural gas development and expansion. Abundance estimates and density surface maps are available for 10 commonly seen marine mammals, including northern resident killer whales, fin whales, humpback whales, and other species with at-risk status under Canadian legislation. Ship noise is the dominant anthropogenic contributor to the marine soundscape of BC, and it is chronic. Underwater noise is now being considered in habitat quality assessments in some countries and in marine spatial planning. We modeled the propagation of underwater noise from ships and weighted the received levels by species-specific audiograms. We overlaid the audiogram-weighted maps of ship audibility with animal density maps. The result is a series of so-called “hotspot” maps of ship noise for all 10 marine mammal species, based on cumulative ship noise energy and average distribution in the boreal summer. South coast waters (Juan de Fuca and Haro Straits) are hotspots for all species that use the area, irrespective of their hearing sensitivity, simply due to ubiquitous ship traffic. Secondary hotspots were found on the central and north coasts (Johnstone Strait and the region around Prince Rupert). These maps can identify where anthropogenic noise is predicted to have above-average impact on species-specific habitat, and where mitigation measures may be most effective. This approach can guide effective mitigation without requiring fleet-wide modification in sites where no animals are present or where the area is used by species that are relatively insensitive to ship noise. PMID:24598866

Comparisons of interdisciplinary ballast water treatment systems and operational experiences from ships.

PubMed

Bakalar, Goran

2016-01-01

There are high functioning and low functioning ballast water treatment systems on board ships. In this study, five systems were analysed so as to methodically examine the operational difficulties for ship crew members while giving important consideration to sustainable environment practices. Multi-criteria analysis, a questionnaire, survey and interviews were used as the research method so as to ascertain and corroborate existing problems on board ships, and the reliability of the systems was calculated. The co-insistency, maintenance and the efficiency of the systems, were shown as being the major problem as there are no systems for tracking ship ballast operations from land. The treatment system that used oxidants was, through multi criteria analysis, evaluated as being the best and was ranked first. However, the survey results showed that the ship's crew had serious problems with this system which difficult to solve during the ship's operations with cargo. The deoxygenation system was the most appropriate according to ballast water treatment criteria in the port or at sea. The treatment system which used electrolysis with oxidant was better in terms of efficacy and the treatment system electrolysis with ultra violet light was better in terms of the criterion environment pollution footprint. During further research, it was shown that 7 % of the surveyed crew members had major problems with operating ballast water treatment systems, including the system which was ranked first through multi criteria analysis. They by-passed these systems while continuing to ballast or de-ballast. It was calculated that of the total time needed for the ballast water treatment system operation, 9 % of this time was used for repairs or maintenance of the systems. Some examples are changing a used UV bulb, cleaning the filter or controlling the amount of oxidant which would be discharged into the sea. A conclusion was made and solution was suggested. The study results emphasised taking action in the interest of protecting the natural world, with particular attention being given to environmental protection to support human life.

Ship emissions inventory, social cost and eco-efficiency in Shanghai Yangshan port

NASA Astrophysics Data System (ADS)

Song, Su

2014-01-01

This study estimated both the in-port ship emissions inventory (CO2, CH4, N2O, PM10, PM2.5, NOx, SOx, CO, and HC) and the emission associated social cost in Yangshan port of Shanghai. A sophisticated activity-based methodology, supported by the ship-by-ship and real-time data from the modern automatic identification system (AIS), was introduced to obtain accurate estimates of ship emissions. The detailed spatial and temporal emission inventories can be used as input for air quality dispersion modeling in the port and vicinities. The social cost of the emission impact on the Yangshan port coastal regions was then assessed based on the emissions inventories. The social cost covers the impact on human health, the environment, and the climate of the coastal community. Finally, the ship emissions was combined with port's basic operation profiles, i.e. container throughput, ship calls, and port revenue, in an attempt to assess the port's “eco-efficiency”, which indicates the port performance with social-economic and environmental concerns. This study filled the gap of previous studies by providing the AIS-supported activity-based emission inventory to facilitate the social cost-benefit analysis for the emission abatement policies. The result shows that i) the amount of in-port ship emissions of CO2, CH4, N2O, PM10, PM2.5, NOx, SOx, CO, and HC in Yangshan port area was 578,444 tons, 10 tons, 33 tons, 1078 tons (PM10, inducing PM2.5), 859 tons (PM2.5 only), 10,758 tons, 5623 tons, 1136 tons, and 519 tons, respectively, with ii) a total social cost of 287 million; iii) the values of the three parameters of the port eco-efficiency performance were 36,528 per 1,000 TEU throughput, 43,993 per ship call, and 44 million per billion US$ port revenue (4.4% of port revenue), respectively in 2009.

High-spatiotemporal-resolution ship emission inventory of China based on AIS data in 2014.

PubMed

Chen, Dongsheng; Wang, Xiaotong; Li, Yue; Lang, Jianlei; Zhou, Ying; Guo, Xiurui; Zhao, Yuehua

2017-12-31

Ship exhaust emissions have been considered a significant source of air pollution, with adverse impacts on the global climate and human health. China, as one of the largest shipping countries, has long been in great need of in-depth analysis of ship emissions. This study for the first time developed a comprehensive national-scale ship emission inventory with 0.005°×0.005° resolution in China for 2014, using the bottom-up method based on Automatic Identification System (AIS) data of the full year of 2014. The emission estimation involved 166,546 unique vessels observed from over 15billion AIS reports, covering OGVs (ocean-going vessels), CVs (coastal vessels) and RVs (river vessels). Results show that the total estimated ship emissions for China in 2014 were 1.1937×10 6 t (SO 2 ), 2.2084×10 6 t (NO X ), 1.807×10 5 t (PM 10 ), 1.665×10 5 t (PM 2.5 ), 1.116×10 5 t (HC), 2.419×10 5 t (CO), and 7.843×10 7 t (CO 2 , excluding RVs), respectively. OGVs were the main emission contributors, with proportions of 47%-74% of the emission totals for different species. Vessel type with the most emissions was container (~43.6%), followed by bulk carrier (~17.5%), oil tanker (~5.7%) and fishing ship (~4.9%). Monthly variations showed that emissions from transport vessels had a low point in February, while fishing ship presented two emission peaks in May and September. In terms of port clusters, ship emissions in BSA (Bohai Sea Area), YRD (Yangtze River Delta) and PRD (Pearl River Delta) accounted for ~13%, ~28% and ~17%, respectively, of the total emissions in China. On the contrast, the average emission intensities in PRD were the highest, followed by the YRD and BSA regions. The establishment of this high-spatiotemporal-resolution ship emission inventory fills the gap of national-scale ship emission inventory of China, and the corresponding ship emission characteristics are expected to provide certain reference significance for the management and control of the ship emissions. Copyright © 2017 Elsevier B.V. All rights reserved.

Emission inventories for ships in the arctic based on satellite sampled AIS data

NASA Astrophysics Data System (ADS)

Winther, Morten; Christensen, Jesper H.; Plejdrup, Marlene S.; Ravn, Erik S.; Eriksson, Ómar F.; Kristensen, Hans Otto

2014-07-01

This paper presents a detailed BC, NOx and SO2 emission inventory for ships in the Arctic in 2012 based on satellite AIS data, ship engine power functions and technology stratified emission factors. Emission projections are presented for the years 2020, 2030 and 2050. Furthermore, the BC, SO2 and O3 concentrations and the deposition of BC are calculated for 2012 and for two arctic shipping scenarios - with or without arctic diversion routes due to a possible polar sea ice extent in the future. In 2012, the largest shares of Arctic ships emissions are calculated for fishing ships (45% for BC, 38% for NOx, 23% for SO2) followed by passenger ships (20%, 17%, 25%), tankers (9%, 13%, 15%), general cargo (8%, 11%, 12%) and container ships (5%, 7%, 8%). In 2050, without arctic diversion routes, the total emissions of BC, NOx and SO2 are expected to change by +16%, -32% and -63%, respectively, compared to 2012. The results for fishing ships are the least certain, caused by a less precise engine power - sailing speed relation. The calculated BC, SO2, and O3 surface concentrations and BC deposition contributions from ships are low as a mean for the whole Arctic in 2012, but locally BC additional contributions reach up to 20% around Iceland, and high additional contributions (100-300%) are calculated in some sea areas for SO2. In 2050, the arctic diversion routes highly influence the calculated surface concentrations and the deposition of BC in the Arctic. During summertime navigation contributions become very visible for BC (>80%) and SO2 (>1000%) along the arctic diversion routes, while the O3 (>10%) and BC deposition (>5%) additional contributions, respectively, get highest over the ocean east of Greenland and in the High Arctic. The geospatial ship type specific emission results presented in this paper have increased the accuracy of the emission inventories for ships in the Arctic. The methodology can be used to estimate shipping emissions in other regions of the world, and hence may serve as an input for other researchers and policy makers working in this field.

Seafloor Geodesy usi­ng Wave Gliders to study Earthquake and Tsunami Hazards at Subduction Zones

NASA Astrophysics Data System (ADS)

Sathiakumar, S.; Barbot, S.; Hill, E.; Peng, D.; Zerucha, J.; Suhaimee, S.; Chia, G.; Salamena, G. G.; Syahailatua, A.

2016-12-01

Land-based GNSS networks are now in place to monitor most subduction zones of the world. These provide valuable information about the amount of­ geodetic strain accumulated in the region, which in turn gives insight into the seismic potential. However, it is usually impossible to resolve activity on the megathrust near the trench using land-based GNSS data alone, given typical signal-to-noise ratios. Ship-based seafloor geodesy is being used today to fill this observation gap. However, surveys using ships are very expensive, tedious and impractical due to the large areas to be covered. Instead of discrete missions using ships, continuous monitoring of the seafloor using autonomous marine robots would aid in understanding the tectonic setting of the seafloor better at a potentially lower cost, as well as help in designing better warning systems. Thus, we are developing seafloor geodesy capabilities using Wave Gliders, a new class of wave-propelled, persistent marine autonomous vehicle using a combination of acoustic and GNSS technologies. We use GNSS/INS to position the platform, and acoustic ranging to locate the seafloor. The GNSS/INS system to be integrated with the Wave Gliders has stringent requirements of low power, light weight, and high accuracy. All these factors are equally important due to limited power and space in the Wave Gliders and the need for highly accurate and precise measurements. With this hardware setup, a limiting factor is the accuracy of measurement of the sound velocity in the water column. We plan to obtain precise positioning of seafloor by exploring a measurement setup that minimizes uncertainties in sound velocity. This will be achieved by making fine-resolution measurements of the two-way travel time of the acoustic waves underwater using the Wave Gliders, and performing statistical signal processing on this data to obtain more reliable sound velocity measurement. This enhanced seafloor geodetic technique using Wave Gliders should enable us to measure deformation of the seafloor over annual and decadal time scales. Combination of seafloor data with land based GPS networks would allow us to study processes from the deep-ocean trench to the coast in a better way, and thereby give a more complete picture of the subduction process.

A Survey of Data-Base Information Systems Relevant to Navy Requirements Planning

DTIC Science & Technology

1983-02-01

SHIPS \\ AK (FEM) T-AK (FEM) AKD/T-AKO _" ’ AKL/T-AKL AKM MULTIPURPOSE CAR 0 SHI’’S AKR VEHICLE CARGO SHIPS . -■, AK3 ANL AO OILER AC • NEW...the most demanding condition of operation for which a ship must be manned. ( a ) At sea in wartime. (b) Capable of performing all offensive... ship , and aircraft) researchers and others could quickly obtain basic information. 3. The Navy currently maintains a number of related

SCANS (Shipping Cask ANalysis System) a microcomputer-based analysis system for shipping cask design review: User`s manual to Version 3a. Volume 1, Revision 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mok, G.C.; Thomas, G.R.; Gerhard, M.A.

SCANS (Shipping Cask ANalysis System) is a microcomputer-based system of computer programs and databases developed at the Lawrence Livermore National Laboratory (LLNL) for evaluating safety analysis reports on spent fuel shipping casks. SCANS is an easy-to-use system that calculates the global response to impact loads, pressure loads and thermal conditions, providing reviewers with an independent check on analyses submitted by licensees. SCANS is based on microcomputers compatible with the IBM-PC family of computers. The system is composed of a series of menus, input programs, cask analysis programs, and output display programs. All data is entered through fill-in-the-blank input screens thatmore » contain descriptive data requests. Analysis options are based on regulatory cases described in the Code of Federal Regulations 10 CFR 71 and Regulatory Guides published by the US Nuclear Regulatory Commission in 1977 and 1978.« less

Cardiovascular disease mortality in British merchant shipping and among British seafarers ashore in Britain.

PubMed

Roberts, Stephen E; Jaremin, Bogdan

2010-01-01

The objective was to investigate trends in work-related mortality from cardiovascular disease (CVD) among seafarers employed in British merchant shipping from 1919 to 2005, to compare CVD mortality among British seafarers at work in British shipping - and ashore in Britain - with that in the general British population, and to investigate work-related CVD mortality in British shipping during recent years according to factors such as rank, nationality, location, and type of ship. A longitudinal study based on examination of death inquiry files and death registers, official death returns, and information from occupational mortality decennial supplements. The main outcome measures were population-based mortality rates and standardised mortality ratios. There was an increase in work-related CVD mortality throughout much of the period from 1919 to 1962, but a subsequent reduction to 2005. Work-related mortality from CVD and ischaemic heart disease (IHD) was lower among seafarers employed in British shipping than in the corresponding general population (SMRs = 0.35 to 0.46), but mortality from CVD among British seafarers ashore in Britain was often increased. An elevated risk of work-related CVD mortality was also identified among the crews of North Sea offshore ships. This study shows a healthy worker effect against CVD mortality among seafarers at work in British shipping, but increased risks among British seafarers ashore in Britain, which would include seafarers discharged through CVD morbidity and other illnesses. The high risks of CVD mortality among seafarers in North Sea supply ships may reflect particular work-related hazards in this sector.

An approach to high speed ship ride quality simulation

NASA Technical Reports Server (NTRS)

Malone, W. L.; Vickery, J. M.

1975-01-01

The high speeds attained by certain advanced surface ships result in a spectrum of motion which is higher in frequency than that of conventional ships. This fact along with the inclusion of advanced ride control features in the design of these ships resulted in an increased awareness of the need for ride criteria. Such criteria can be developed using data from actual ship operations in varied sea states or from clinical laboratory experiments. A third approach is to simulate ship conditions using measured or calculated ship motion data. Recent simulations have used data derived from a math model of Surface Effect Ship (SES) motion. The model in turn is based on equations of motion which have been refined with data from scale models and SES of up to 101 600-kg (100-ton) displacement. Employment of broad band motion emphasizes the use of the simulators as a design tool to evaluate a given ship configuration in several operational situations and also serves to provide data as to the overall effect of a given motion on crew performance and physiological status.

Influences of the separation distance, ship speed and channel dimension on ship maneuverability in a confined waterway

NASA Astrophysics Data System (ADS)

Du, Peng; Ouahsine, Abdellatif; Sergent, Philippe

2018-05-01

Ship maneuvering in the confined inland waterway is investigated using the system-based method, where a nonlinear transient hydrodynamic model is adopted and confinement models are implemented to account for the influence of the channel bank and bottom. The maneuvering model is validated using the turning circle test, and the confinement model is validated using the experimental data. The separation distance, ship speed, and channel width are then varied to investigate their influences on ship maneuverability. With smaller separation distances and higher speeds near the bank, the ship's trajectory deviates more from the original course and the bow is repelled with a larger yaw angle, which increase the difficulty of maneuvering. Smaller channel widths induce higher advancing resistances on the ship. The minimum distance to the bank are extracted and studied. It is suggested to navigate the ship in the middle of the channel and with a reasonable speed in the restricted waterway.

Nonlinear optimization method of ship floating condition calculation in wave based on vector

NASA Astrophysics Data System (ADS)

Ding, Ning; Yu, Jian-xing

2014-08-01

Ship floating condition in regular waves is calculated. New equations controlling any ship's floating condition are proposed by use of the vector operation. This form is a nonlinear optimization problem which can be solved using the penalty function method with constant coefficients. And the solving process is accelerated by dichotomy. During the solving process, the ship's displacement and buoyant centre have been calculated by the integration of the ship surface according to the waterline. The ship surface is described using an accumulative chord length theory in order to determine the displacement, the buoyancy center and the waterline. The draught forming the waterline at each station can be found out by calculating the intersection of the ship surface and the wave surface. The results of an example indicate that this method is exact and efficient. It can calculate the ship floating condition in regular waves as well as simplify the calculation and improve the computational efficiency and the precision of results.

The complex network of global cargo ship movements.

PubMed

Kaluza, Pablo; Kölzsch, Andrea; Gastner, Michael T; Blasius, Bernd

2010-07-06

Transportation networks play a crucial role in human mobility, the exchange of goods and the spread of invasive species. With 90 per cent of world trade carried by sea, the global network of merchant ships provides one of the most important modes of transportation. Here, we use information about the itineraries of 16 363 cargo ships during the year 2007 to construct a network of links between ports. We show that the network has several features that set it apart from other transportation networks. In particular, most ships can be classified into three categories: bulk dry carriers, container ships and oil tankers. These three categories do not only differ in the ships' physical characteristics, but also in their mobility patterns and networks. Container ships follow regularly repeating paths whereas bulk dry carriers and oil tankers move less predictably between ports. The network of all ship movements possesses a heavy-tailed distribution for the connectivity of ports and for the loads transported on the links with systematic differences between ship types. The data analysed in this paper improve current assumptions based on gravity models of ship movements, an important step towards understanding patterns of global trade and bioinvasion.

The complex network of global cargo ship movements

PubMed Central

Kaluza, Pablo; Kölzsch, Andrea; Gastner, Michael T.; Blasius, Bernd

2010-01-01

Transportation networks play a crucial role in human mobility, the exchange of goods and the spread of invasive species. With 90 per cent of world trade carried by sea, the global network of merchant ships provides one of the most important modes of transportation. Here, we use information about the itineraries of 16 363 cargo ships during the year 2007 to construct a network of links between ports. We show that the network has several features that set it apart from other transportation networks. In particular, most ships can be classified into three categories: bulk dry carriers, container ships and oil tankers. These three categories do not only differ in the ships' physical characteristics, but also in their mobility patterns and networks. Container ships follow regularly repeating paths whereas bulk dry carriers and oil tankers move less predictably between ports. The network of all ship movements possesses a heavy-tailed distribution for the connectivity of ports and for the loads transported on the links with systematic differences between ship types. The data analysed in this paper improve current assumptions based on gravity models of ship movements, an important step towards understanding patterns of global trade and bioinvasion. PMID:20086053

Ship collision risk assessment for the Singapore Strait.

PubMed

Qu, Xiaobo; Meng, Qiang; Suyi, Li

2011-11-01

The Singapore Strait is considered as the bottleneck and chokepoint of the shipping routes connecting the Indian and the Pacific Ocean. Therefore, the ship collision risk assessment is of significant importance for ships passing through the narrow, shallow, and busy waterway. In this paper, three ship collision risk indices are initially proposed to quantitatively assess the ship collision risks in the Strait: index of speed dispersion, degree of acceleration and deceleration, and number of fuzzy ship domain overlaps. These three risk indices for the Singapore Strait are estimated by using the real-time ship locations and sailing speeds provide by Lloyd's MIU automatic identification system (AIS). Based on estimation of these three risk indices, it can be concluded that Legs 4W, 5W, 11E, and 12E are the most risky legs in the Strait. Therefore, the ship collision risk reduction solutions should be prioritized being implemented in these four legs. This study also finds that around 25% of the vessels sail with a speed in excess of the speed limit, which results in higher potentials of ship collision. Analysis indicates that the safety level would be significantly improved if all the vessels follow the passage guidelines. Copyright © 2011 Elsevier Ltd. All rights reserved.

Ship detection leveraging deep neural networks in WorldView-2 images

NASA Astrophysics Data System (ADS)

Yamamoto, T.; Kazama, Y.

2017-10-01

Interpretation of high-resolution satellite images has been so difficult that skilled interpreters must have checked the satellite images manually because of the following issues. One is the requirement of the high detection accuracy rate. The other is the variety of the target, taking ships for example, there are many kinds of ships, such as boat, cruise ship, cargo ship, aircraft carrier, and so on. Furthermore, there are similar appearance objects throughout the image; therefore, it is often difficult even for the skilled interpreters to distinguish what object the pixels really compose. In this paper, we explore the feasibility of object extraction leveraging deep learning with high-resolution satellite images, especially focusing on ship detection. We calculated the detection accuracy using the WorldView-2 images. First, we collected the training images labelled as "ship" and "not ship". After preparing the training data, we defined the deep neural network model to judge whether ships are existing or not, and trained them with about 50,000 training images for each label. Subsequently, we scanned the evaluation image with different resolution windows and extracted the "ship" images. Experimental result shows the effectiveness of the deep learning based object detection.

Navy Enhanced Sierra Mechanics (NESM): Toolbox for predicting Navy shock and damage

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moyer, Thomas; Stergiou, Jonathan; Reese, Garth

Here, the US Navy is developing a new suite of computational mechanics tools (Navy Enhanced Sierra Mechanics) for the prediction of ship response, damage, and shock environments transmitted to vital systems during threat weapon encounters. NESM includes fully coupled Euler-Lagrange solvers tailored to ship shock/damage predictions. NESM is optimized to support high-performance computing architectures, providing the physics-based ship response/threat weapon damage predictions needed to support the design and assessment of highly survivable ships. NESM is being employed to support current Navy ship design and acquisition programs while being further developed for future Navy fleet needs.

Study on lockage safety of LNG-fueled ships based on FSA

PubMed Central

Lv, Pengfei; Zhuang, Yuan; Deng, Jian; Su, Wei

2017-01-01

In the present study, formal safety assessment (FSA) is introduced to investigate lockage safety of LNG-fueled ships. Risk sources during lockage of LNG-fueled ships in four typical scenarios, namely, navigation between two dams, lockage, anchorage, and fueling, are identified, and studied in combination with fundamental leakage probabilities of various components of LNG storage tanks, and simulation results of accident consequences. Some suggestions for lockage safety management of LNG-fueled ships are then proposed. The present research results have certain practical significance for promoting applications of LNG-fueled ships along Chuanjiang River and in Three Gorges Reservoir Region. PMID:28437482

Navy Enhanced Sierra Mechanics (NESM): Toolbox for predicting Navy shock and damage

DOE PAGES

Moyer, Thomas; Stergiou, Jonathan; Reese, Garth; ...

2016-05-25

Here, the US Navy is developing a new suite of computational mechanics tools (Navy Enhanced Sierra Mechanics) for the prediction of ship response, damage, and shock environments transmitted to vital systems during threat weapon encounters. NESM includes fully coupled Euler-Lagrange solvers tailored to ship shock/damage predictions. NESM is optimized to support high-performance computing architectures, providing the physics-based ship response/threat weapon damage predictions needed to support the design and assessment of highly survivable ships. NESM is being employed to support current Navy ship design and acquisition programs while being further developed for future Navy fleet needs.

Health and Climate Impacts of Ocean-Going Vessels in East Asia

NASA Technical Reports Server (NTRS)

Liu, Huan; Fu, Mingliang; Jin, Xinxin; Shang, Yi; Shindell, Drew; Faluvegi, Greg; Shindell, Cary; He, Kebin

2016-01-01

East Asia has the most rapidly growing shipping emissions of both CO2 and traditional air pollutants, but the least in-depth analysis. Full evaluation of all pollutants is needed to assess the impacts of shipping emissions. Here, using an advanced method based on detailed dynamic ship activity data, we show that shipping emissions in East Asia accounted for 16% of global shipping CO2 in 2013, compared to only 4-7% in 2002-2005. Increased emissions lead to large adverse health impacts, with 14,500-37,500 premature deaths per year. Global mean radiative forcing from East Asian shipping is initially negative, but would become positive after approximately eight years for constant current emissions. As a large fraction of vessels are registered elsewhere, joint efforts are necessary to reduce emissions and mitigate the climate and health impacts of shipping in the region.

Global ship accidents and ocean swell-related sea states

NASA Astrophysics Data System (ADS)

Zhang, Zhiwei; Li, Xiao-Ming

2017-11-01

With the increased frequency of shipping activities, navigation safety has become a major concern, especially when economic losses, human casualties and environmental issues are considered. As a contributing factor, the sea state plays a significant role in shipping safety. However, the types of dangerous sea states that trigger serious shipping accidents are not well understood. To address this issue, we analyzed the sea state characteristics during ship accidents that occurred in poor weather or heavy seas based on a 10-year ship accident dataset. Sea state parameters of a numerical wave model, i.e., significant wave height, mean wave period and mean wave direction, were analyzed for the selected ship accident cases. The results indicated that complex sea states with the co-occurrence of wind sea and swell conditions represent threats to sailing vessels, especially when these conditions include similar wave periods and oblique wave directions.

Study on the propagation and dissipation of inland ship congestion under different control strategies

NASA Astrophysics Data System (ADS)

Chen, Yanyi; Wu, Hongyu; Wen, Zhe

2017-05-01

Inland waterway transportation is an important part of the comprehensive transportation system of sustainable development, and it is also a way of transportation which is restricted by natural conditions greatly. In recent years, the problems of insufficient traffic capacity of The Three Gorges become prominent due to the increasing in the number of ships. And the ship's detention caused by gale, frog, accident and one-way traffic in dry season has occurred, which not only increased the pressure of the navigable waterway but also seriously affected the safety of shipping. Based on the different types of ships, the Arena software was used to simulate the ship traffic flow. The paper analyzed the traffic congestion propagation and dissipation rule of the ship under different navigation control methods, and provided decision reference for the navigation management department to formulate the relevant navigation control strategy.

Research Opportunities on board Virgin Galactic's SpaceShipTwo

NASA Astrophysics Data System (ADS)

Attenborough, S.; Pomerantz, W.; Stephens, K.

2013-09-01

Virgin Galactic is building the world's first commercial spaceline. Our suborbital spaceflight system, pictured in Figure 1, consists of two vehicles: WhiteKnightTwo (WK2) and SpaceShipTwo (SS2). WhiteKnightTwo is a four-engine, dual-fuselage jet aircraft capable of high-altitude heavy lift missions, including, but not limited to fulfilling its role as a mothership for SpaceShipTwo, an air-launched, suborbital spaceplane capable of routinely reaching an apogee up to 110 kilometers. In conjunction, these two vehicles allow access to space and to regions of the atmosphere ranging from the troposphere to the thermosphere; additionally, they provide extended periods of microgravity in a reliable and affordable way. SpaceShipTwo, with a payload capacity of up to 1,300 lbs. (~600 kg), features payload mounting interfaces that are compatible with standard architectures such as NASA Space Shuttle Middeck Lockers, Cargo Transfer Bags, and server racks, in addition to custom structures. With the standard interface, payloads are allowed access to the large 17 inch diameter cabin windows for external observations. Each dedicated research flight will be accompanied by a Virgin Galactic Flight Test Engineer, providing an opportunity for limited in-flight interaction. In addition, tended payloads - a flight that includes the researcher and his or her payload - are also an option. At a price point that is highly competitive with parabolic aircraft and sounding rockets and significantly cheaper than orbital flights, SpaceShipTwo is a unique platform that can provide frequent and repeatable research opportunities. Suborbital flights on SpaceShipTwo offer researchers several minutes of microgravity time and views of the external environment in the upper atmosphere and in outer space. In addition to serving as an important research platform in and of itself, SpaceShipTwo also offers researchers a means to test, iterate, and calibrate experiments designed for orbital platforms, including the International Space Station as well as LauncherOne, Virgin Galactic's dedicated launch vehicle for small (~500 lbs. / ~225 kg) satellites. Flights on SpaceShipTwo can be booked directly through Virgin Galactic. Various funding sources may be available for the research, including through NASA programs such as the Flight Opportunities Program, Game Changing Development Program, or Research Opportunities in Space and Earth Science (ROSES). More information about the SpaceShipTwo research platform, including a detailed Payload User's Guide, can be found at our website: http://www.virgingalactic.com/research.

Application of Sensor Technology for the Efficient Positioningand Assembling of Ship Blocks

NASA Astrophysics Data System (ADS)

Lee, Sangdon; SeongbaeEun; Jung, Jai Jin; Song, Hacheol

2010-09-01

This paper proposes the application of sensor technology to assemble ship blocks efficiently. A sensor-based monitoring system is designed and implemented to improve shipbuilding productivity by reducing the labor cost for the adjustment of adequate positioning between ship blocks during pre-erection or erection stage. For the real-time remote monitoring of relative distances between two ship blocks, sensor nodes are applied to measure the distances between corresponding target points on the blocks. Highly precise positioning data can be transferred to a monitoring server via wireless network, and analyzed to support the decision making which needs to determine the next construction process; further adjustment or seam welding between the ship blocks. The developed system is expected to put to practical use, and increase the productivity during ship blocks assembly.

Littoral Combat Ship: Deployment of USS Freedom Revealed Risks in Implementing Operational Concepts and Uncertain Costs

DTIC Science & Technology

2014-07-01

ApprovedOMB No. 0704-0188 Public reporting burden for the collection of information is estimated to average 1 hour per response, including the time for...such as systems reliability and crew sleep hours . However, several factors limited the operational lessons learned. For example, mechanical problems...concepts. In February 2010, we reported several potential risks in implementing the new operational concepts for the LCS. 4 In its report

Defense Management Education and Training

DTIC Science & Technology

1991-07-01

loading, stowing, and discharge of a cargo ship . This course is intended for ocean cargo specialists and military marine terminal operations...stowage planning. The student prepares a cargo prestowage plan, the USNS ALGOL (T- AKR 287). Mathematical ability is critical. PREREQUISITES: Personnel...AFIT/LS Performance Measurement Data (JT) QMT 372 Reliability (AF) OS/R/15 days AFIT/LS 0 2- A -24 DoD ",010.16-C QMT 540 Advanced Contract Pricing OS/R/10

Somali Piracy and Anti-Shipping Activity Messages: Lessons for a Successful Counterpiracy Strategy

DTIC Science & Technology

2014-06-01

solving the differences found in each organization’s reporting. This suggestion seems valid and demonstrates an unbiased approach. 19 The studies...agrees the IMB data sets are not free from debate and criticism, yet claims the reports provide the only consistent and reliable set of figures to...different approach to using piracy incident reports. Hastings (2009) explores the political and economic landscapes of failed and weak states to determine

GPHS-RTGs in support of the Cassini mission

NASA Astrophysics Data System (ADS)

1994-04-01

This report is organized by the program task structure as follows: (1) spacecraft integration and liaison; (2) engineering support; (3) safety; (4) qualified unicouple fabrication; (5) ETG fabrication, assembly, and test; (6) ground support equipment (GSE); (7) RTG shipping and launch support; (8) designs, reviews, and mission applications; (9) project management, quality assurance and reliability, contract changes, noncapital contractor acquired government owned property (CAGO) acquisition, and CAGO maintenance; and (10) CAGO acquisition.

Adaptability of solar energy conversion systems on ships

NASA Astrophysics Data System (ADS)

Visa, I.; Cotorcea, A.; Neagoe, M.; Moldovan, M.

2016-08-01

International trade of goods largely uses maritime/transoceanic ships driven by engines using fossil fuels. This two centuries tradition is technologically mature but significantly adds to the CO2 emissions; therefore, recent trends focus on on-board implementation of systems converting the solar energy into power (photovoltaic systems) or heat (solar-thermal systems). These systems are carbon-emissions free but are still under research and plenty of effort is devoted to fast reach maturity and feasibility. Unlike the systems implemented in a specific continental location, the design of solar energy conversion systems installed on shipboard has to face the problem generated by the system base motion along with the ship travelling on routes at different latitudes: the navigation direction and sense and roll-pitch combined motion with reduced amplitude, but with relatively high frequency. These raise highly interesting challenges in the design and development of mechanical systems that support the maximal output in terms of electricity or heat. The paper addresses the modelling of the relative position of a solar energy conversion surface installed on a ship according to the current position of the sun; the model is based on the navigation trajectory/route, ship motion generated by waves and the relative sun-earth motion. The model describes the incidence angle of the sunray on the conversion surface through five characteristic angles: three used to define the ship orientation and two for the solar angles; based on, their influence on the efficiency in solar energy collection is analyzed by numerical simulations and appropriate recommendations are formulated for increasing the solar energy conversion systems adaptability on ships.

Actions for prevention and control of health threats related to maritime transport in European Union.

PubMed

Hadjichristodoulou, Christos; Mouchtouri, Varvara A; Guglielmetti, Paolo; Lemos, Cinthia Menel; Nichols, Gordon; Paux, Thierry; Schlaich, Clara; Cornejo, Miguel Davila; Martinez, Carmen Varela; Dionisio, Mauro; Rehmet, Sybille; Jaremin, Bogdan; Kremastinou, Jenny

2013-01-01

Actions at European Union level for International Health Regulations (IHR) 2005 implementation and maritime transport were focused on two European projects implemented between 2006 and 2011. Situation analysis and needs assessment were conducted, a Manual including European standards and best practice and training material was developed and training courses were delivered. Ship-to-port and port-to-port communication web-based network and database for recording IHR Ship Sanitation Certificates (SSC) were established. Fifty pilot inspections based on the Manual were conducted on passenger ships. A total of 393 corrective actions were implemented according to recommendations given to Captains during pilot inspections. The web-based communication network of competent authorities at ports in EU Member States was used to manage 13 events/outbreaks (dengue fever, Legionnaires' disease, gastroenteritis, meningitis, varicella and measles). The European information database system was used for producing and recording 1018 IHR SSC by 156 inspectors in 6 countries in accordance with the WHO Handbook for inspection of ships and issuance of SSC. Implementation of corrective actions after pilot inspections increased the level of compliance with the hygiene standards in passenger ships sailing within the EU waters and improved hygiene conditions. The communication tool contributed to improvement of outbreak identification and better management through rapid sharing of public health information, allowing a more timely and coordinated response. After the implementation of actions on passenger ships, the European Commission co-funded a Joint action that will expand the activities to all types of ships and chemical, biological and radio-nuclear threats (deliberate acts/accidental). Copyright © 2013 Elsevier Ltd. All rights reserved.

Local region power spectrum-based unfocused ship detection method in synthetic aperture radar images

NASA Astrophysics Data System (ADS)

Wei, Xiangfei; Wang, Xiaoqing; Chong, Jinsong

2018-01-01

Ships on synthetic aperture radar (SAR) images will be severely defocused and their energy will disperse into numerous resolution cells under long SAR integration time. Therefore, the image intensity of ships is weak and sometimes even overwhelmed by sea clutter on SAR image. Consequently, it is hard to detect the ships from SAR intensity images. A ship detection method based on local region power spectrum of SAR complex image is proposed. Although the energies of the ships are dispersed on SAR intensity images, their spectral energies are rather concentrated or will cause the power spectra of local areas of SAR images to deviate from that of sea surface background. Therefore, the key idea of the proposed method is to detect ships via the power spectra distortion of local areas of SAR images. The local region power spectrum of a moving target on SAR image is analyzed and the way to obtain the detection threshold through the probability density function (pdf) of the power spectrum is illustrated. Numerical P- and L-band airborne SAR ocean data are utilized and the detection results are also illustrated. Results show that the proposed method can well detect the unfocused ships, with a detection rate of 93.6% and a false-alarm rate of 8.6%. Moreover, by comparing with some other algorithms, it indicates that the proposed method performs better under long SAR integration time. Finally, the applicability of the proposed method and the way of parameters selection are also discussed.

Effects of ship-induced waves on aquatic ecosystems.

PubMed

Gabel, Friederike; Lorenz, Stefan; Stoll, Stefan

2017-12-01

Most larger water bodies worldwide are used for navigation, and the intensity of commercial and recreational navigation is expected to further increase. Navigation profoundly affects aquatic ecosystems. To facilitate navigation, rivers are trained and developed, and the direct effects of navigation include chemical and biological impacts (e.g., inputs of toxic substances and dispersal of non-native species, respectively). Furthermore, propagating ships create hydrodynamic alterations, often simply summarized as waves. Although ship-induced waves are recognized as influential stressors, knowledge on their effects is poorly synthesized. We present here a review on the effects of ship-induced waves on the structure, function and services of aquatic ecosystems based on more than 200 peer reviewed publications and technical reports. Ship-induced waves act at multiple organizational levels and different spatial and temporal scales. All the abiotic and biotic components of aquatic ecosystems are affected, from the sediment and nutrient budget to the planktonic, benthic and fish communities. We highlight how the effects of ship-induced waves cascade through ecosystems and how different effects interact and feed back into the ecosystem finally leading to altered ecosystem services and human health effects. Based on this synthesis of wave effects, we discuss strategies for mitigation. This may help to develop scientifically based and target-oriented management plans for navigational waters that optimize abiotic and biotic integrity and their ecosystem services and uses. Copyright © 2017 Elsevier B.V. All rights reserved.

Parenchymal asbestosis due to primary asbestos exposure among ship-breaking workers: report of the first cases from Bangladesh.

PubMed

Muralidhar, Venkiteswaran; Ahasan, Md Faizul; Khan, Ahad Mahmud

2017-11-03

We report for the first time asbestosis among ship-breaking workers of Sitakunda in Bangladesh who were exposed to asbestos during ship-based and beach-based operations for at least 10 years. Asbestosis was present among 35% of workers. Years of work (>20) and forced vital capacity (<80% of predicted) were significantly associated with the disease. Currently, global ship-breaking operations are mainly concentrated in the Indian subcontinent, and Bangladesh has the majority share. Ninety per cent of domestic steel is produced in the ship-breaking operations in Bangladesh and is an important contributor to the economy. It also gives employment to more than 100 000 people. It is imperative to medically check up all the workers for benign and malignant diseases causally related to asbestos among these vulnerable population of workers. © BMJ Publishing Group Ltd (unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Ship-bridge collision monitoring system based on flexible quantum tunneling composite with cushioning capability

NASA Astrophysics Data System (ADS)

Zheng, Qiaofeng; Han, Baoguo; Ou, Jinping

2018-07-01

In this paper, a ship-bridge collision monitoring system based on flexible quantum tunneling composite (QTC) with cushioning capability is proposed by investigating the sensing capability and positioning capability of QTC to collisions. QTCs with different rubber matrix and thickness were fabricated, and collision tests between steel ball and QTCs sensors were designed to simulate ship-bridge collision. The results show that QTCs have a sensing range over 50 MPa with stress resolution ranging between 0.017 and 0.13 MPa, enough to achieve the full-time monitoring of ship-bridge collision. The system has instant and repeatable respond to impact load, and can accurately position the collisions. Moreover, QTC can remarkably absorb the kinetic energy during collisions, exhibiting excellent cushioning capability. These findings indicate the proposed ship-bridge collision monitoring system has great potential for application to detecting collision information such as collision occurrence and duration, impact load and collision location, as well as providing basis for citizen evacuation, post-accident damage estimation and rescue strategy.

Ship detection from high-resolution imagery based on land masking and cloud filtering

NASA Astrophysics Data System (ADS)

Jin, Tianming; Zhang, Junping

2015-12-01

High resolution satellite images play an important role in target detection application presently. This article focuses on the ship target detection from the high resolution panchromatic images. Taking advantage of geographic information such as the coastline vector data provided by NOAA Medium Resolution Coastline program, the land region is masked which is a main noise source in ship detection process. After that, the algorithm tries to deal with the cloud noise which appears frequently in the ocean satellite images, which is another reason for false alarm. Based on the analysis of cloud noise's feature in frequency domain, we introduce a windowed noise filter to get rid of the cloud noise. With the help of morphological processing algorithms adapted to target detection, we are able to acquire ship targets in fine shapes. In addition, we display the extracted information such as length and width of ship targets in a user-friendly way i.e. a KML file interpreted by Google Earth.

An investigation into the vertical axis control power requirements for landing VTOL type aircraft onboard nonaviation ships in various sea states

NASA Technical Reports Server (NTRS)

Stevens, M. E.; Roskam, J.

1985-01-01

The problem of determining the vertical axis control requirements for landing a VTOL aircraft on a moving ship deck in various sea states is examined. Both a fixed-base piloted simulation and a nonpiloted simulation were used to determine the landing performance as influenced by thrust-to-weight ratio, vertical damping, and engine lags. The piloted simulation was run using a fixed-based simulator at Ames Research center. Simplified versions of an existing AV-8A Harrier model and an existing head-up display format were used. The ship model used was that of a DD963 class destroyer. Simplified linear models of the pilot, aircraft, ship motion, and ship air-wake turbulence were developed for the nonpiloted simulation. A unique aspect of the nonpiloted simulation was the development of a model of the piloting strategy used for shipboard landing. This model was refined during the piloted simulation until it provided a reasonably good representation of observed pilot behavior.

Ship Detection Based on Multiple Features in Random Forest Model for Hyperspectral Images

NASA Astrophysics Data System (ADS)

Li, N.; Ding, L.; Zhao, H.; Shi, J.; Wang, D.; Gong, X.

2018-04-01

A novel method for detecting ships which aim to make full use of both the spatial and spectral information from hyperspectral images is proposed. Firstly, the band which is high signal-noise ratio in the range of near infrared or short-wave infrared spectrum, is used to segment land and sea on Otsu threshold segmentation method. Secondly, multiple features that include spectral and texture features are extracted from hyperspectral images. Principal components analysis (PCA) is used to extract spectral features, the Grey Level Co-occurrence Matrix (GLCM) is used to extract texture features. Finally, Random Forest (RF) model is introduced to detect ships based on the extracted features. To illustrate the effectiveness of the method, we carry out experiments over the EO-1 data by comparing single feature and different multiple features. Compared with the traditional single feature method and Support Vector Machine (SVM) model, the proposed method can stably achieve the target detection of ships under complex background and can effectively improve the detection accuracy of ships.

Remote sensing image ship target detection method based on visual attention model

NASA Astrophysics Data System (ADS)

Sun, Yuejiao; Lei, Wuhu; Ren, Xiaodong

2017-11-01

The traditional methods of detecting ship targets in remote sensing images mostly use sliding window to search the whole image comprehensively. However, the target usually occupies only a small fraction of the image. This method has high computational complexity for large format visible image data. The bottom-up selective attention mechanism can selectively allocate computing resources according to visual stimuli, thus improving the computational efficiency and reducing the difficulty of analysis. Considering of that, a method of ship target detection in remote sensing images based on visual attention model was proposed in this paper. The experimental results show that the proposed method can reduce the computational complexity while improving the detection accuracy, and improve the detection efficiency of ship targets in remote sensing images.

46 CFR Appendix C to Part 404 - Procedures for Annual Review of Base Pilotage Rates

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 8 2013-10-01 2013-10-01 false Procedures for Annual Review of Base Pilotage Rates C Appendix C to Part 404 Shipping COAST GUARD (GREAT LAKES PILOTAGE), DEPARTMENT OF HOMELAND SECURITY GREAT LAKES PILOTAGE RATEMAKING Pt. 404, App. C Appendix C to Part 404—Procedures for Annual Review of Base...

46 CFR Appendix C to Part 404 - Procedures for Annual Review of Base Pilotage Rates

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 8 2014-10-01 2014-10-01 false Procedures for Annual Review of Base Pilotage Rates C Appendix C to Part 404 Shipping COAST GUARD (GREAT LAKES PILOTAGE), DEPARTMENT OF HOMELAND SECURITY GREAT LAKES PILOTAGE RATEMAKING Pt. 404, App. C Appendix C to Part 404—Procedures for Annual Review of Base...

A historical reconstruction of ships' fuel consumption and emissions

NASA Astrophysics Data System (ADS)

Endresen, Øyvind; Sørgârd, Eirik; Behrens, Hanna Lee; Brett, Per Olaf; Isaksen, Ivar S. A.

2007-06-01

Shipping activity has increased considerably over the last century and currently represents a significant contribution to the global emissions of pollutants and greenhouse gases. Despite this, information about the historical development of fuel consumption and emissions is generally limited, with little data published pre-1950 and large deviations reported for estimates covering the last 3 decades. To better understand the historical development in ship emissions and the uncertainties associated with the estimates, we present fuel-based CO2 and SO2 emission inventories from 1925 up to 2002 and activity-based estimates from 1970 up to 2000. The global CO2 emissions from ships in 1925 have been estimated to 229 Tg (CO2), growing to about 634 Tg (CO2) in 2002. The corresponding SO2 emissions are about 2.5 Tg (SO2) and 8.5 Tg (SO2), respectively. Our activity-based estimates of fuel consumption from 1970 to 2000, covering all oceangoing civil ships above or equal to 100 gross tonnage (GT), are lower compared to previous activity-based studies. We have applied a more detailed model approach, which includes variation in the demand for sea transport, as well as operational and technological changes of the past. This study concludes that the main reason for the large deviations found in reported inventories is the applied number of days at sea. Moreover, our modeling indicates that the ship size and the degree of utilization of the fleet, combined with the shift to diesel engines, have been the major factors determining yearly fuel consumption. Interestingly, the model results from around 1973 suggest that the fleet growth is not necessarily followed by increased fuel consumption, as technical and operational characteristics have changed. Results from this study indicate that reported sales over the last 3 decades seems not to be significantly underreported as previous simplified activity-based studies have suggested. The results confirm our previously reported modeling estimates for year 2000. Previous activity-based studies have not considered ships less than 100 GT (e.g., today some 1.3 million fishing vessels), and we suggest that this fleet could account for an important part of the total fuel consumption (˜10%).

Error trends in SASS winds as functions of atmospheric stability and sea surface temperature

NASA Technical Reports Server (NTRS)

Liu, W. T.

1983-01-01

Wind speed measurements obtained with the scatterometer instrument aboard the Seasat satellite are compared equivalent neutral wind measurements obtained from ship reports in the western N. Atlantic and eastern N. Pacific where the concentration of ship reports are high and the ranges of atmospheric stability and sea surface temperature are large. It is found that at low wind speeds the difference between satellite measurements and surface reports depends on sea surface temperature. At wind speeds higher than 8 m/s the dependence was greatly reduced. The removal of systematic errors due to fluctuations in atmospheric stability reduced the r.m.s. difference from 1.7 m/s to 0.8 m/s. It is suggested that further clarification of the effects of fluctuations in atmospheric stability on Seasat wind speed measurements should increase their reliability in the future.

Material handling robot system for flow-through storage applications

NASA Astrophysics Data System (ADS)

Dill, James F.; Candiloro, Brian; Downer, James; Wiesman, Richard; Fallin, Larry; Smith, Ron

1999-01-01

This paper describes the design, development and planned implementation of a system of mobile robots for use in flow through storage applications. The robots are being designed with on-board embedded controls so that they can perform their tasks as semi-autonomous workers distributed within a centrally controlled network. On the storage input side, boxes will be identified by bar-codes and placed into preassigned flow through bins. On the shipping side, orders will be forwarded to the robots from a central order processing station and boxes will be picked from designated storage bins following proper sequencing to permit direct loading into trucks for shipping. Because of the need to maintain high system availability, a distributed control strategy has been selected. When completed, the system will permit robots to be dynamically reassigned responsibilities if an individual unit fails. On-board health diagnostics and condition monitoring will be used to maintain high reliability of the units.

Water Safety Plan on cruise ships: a promising tool to prevent waterborne diseases.

PubMed

Mouchtouri, Varvara A; Bartlett, Christopher L R; Diskin, Arthur; Hadjichristodoulou, Christos

2012-07-01

Legionella spp. and other waterborne pathogens have been isolated from various water systems on land based premises as well as on ships and cases of Legionnaires' disease have been associated with both sites. Peculiarities of cruise ships water systems make the risk management a challenging process. The World Health Organization suggests a Water Safety Plan (WSP) as the best approach to mitigate risks and hazards such as Legionella spp. and others. To develop WSP on a cruise ship and discuss challenges, perspectives and key issues to success. Hazards and hazardous events were identified and risk assessment was conducted of the ship water system. Ship company management, policies and procedures were reviewed, site visits were conducted, findings and observations were recorded and discussed with engineers and key crew members were interviewed. A total of 53 hazards and hazardous events were taken into consideration for the risk assessment and additional essential barriers were established when needed. Most of them concerned control measures for biofilm development and Legionella spp. contamination. A total of 29 operational limits were defined. Supplementary verification and supportive programs were established. Application of the WSP to ship water systems, including potable water, recreational water facilities and decorative water features and fountains, is expected to improve water management on ships. The success of a WSP depends on support from senior management, commitment of the Captain and crew members, correct execution of all steps of a risk assessment and practicality and applicability in routine operation. The WSP provides to shipping industry a new approach and a move toward evidence based water safety policy. Copyright © 2012 Elsevier B.V. All rights reserved.

Estimating air emissions from ships: Meta-analysis of modelling approaches and available data sources

NASA Astrophysics Data System (ADS)

Miola, Apollonia; Ciuffo, Biagio

2011-04-01

Maritime transport plays a central role in the transport sector's sustainability debate. Its contribution to air pollution and greenhouse gases is significant. An effective policy strategy to regulate air emissions requires their robust estimation in terms of quantification and location. This paper provides a critical analysis of the ship emission modelling approaches and data sources available, identifying their limits and constraints. It classifies the main methodologies on the basis of the approach followed (bottom-up or top-down) for the evaluation and geographic characterisation of emissions. The analysis highlights the uncertainty of results from the different methods. This is mainly due to the level of uncertainty connected with the sources of information that are used as inputs to the different studies. This paper describes the sources of the information required for these analyses, paying particular attention to AIS data and to the possible problems associated with their use. One way of reducing the overall uncertainty in the results could be the simultaneous use of different sources of information. This paper presents an alternative methodology based on this approach. As a final remark, it can be expected that new approaches to the problem together with more reliable data sources over the coming years could give more impetus to the debate on the global impact of maritime traffic on the environment that, currently, has only reached agreement via the "consensus" estimates provided by IMO (2009).

Are greenhouse gas emissions from international shipping a type of marine pollution?

PubMed

Shi, Yubing

2016-12-15

Whether greenhouse gas emissions from international shipping are a type of marine pollution is a controversial issue and is currently open to debate. This article examines the current treaty definitions of marine pollution, and applies them to greenhouse gas emissions from ships. Based on the legal analysis of treaty definitions and relevant international and national regulation on this issue, this article asserts that greenhouse gas emissions from international shipping are a type of 'conditional' marine pollution. Copyright © 2016 Elsevier Ltd. All rights reserved.

Ship Trim Optimization: Assessment of Influence of Trim on Resistance of MOERI Container Ship

PubMed Central

Duan, Wenyang

2014-01-01

Environmental issues and rising fuel prices necessitate better energy efficiency in all sectors. Shipping industry is a stakeholder in environmental issues. Shipping industry is responsible for approximately 3% of global CO2 emissions, 14-15% of global NOX emissions, and 16% of global SOX emissions. Ship trim optimization has gained enormous momentum in recent years being an effective operational measure for better energy efficiency to reduce emissions. Ship trim optimization analysis has traditionally been done through tow-tank testing for a specific hullform. Computational techniques are increasingly popular in ship hydrodynamics applications. The purpose of this study is to present MOERI container ship (KCS) hull trim optimization by employing computational methods. KCS hull total resistances and trim and sinkage computed values, in even keel condition, are compared with experimental values and found in reasonable agreement. The agreement validates that mesh, boundary conditions, and solution techniques are correct. The same mesh, boundary conditions, and solution techniques are used to obtain resistance values in different trim conditions at Fn = 0.2274. Based on attained results, optimum trim is suggested. This research serves as foundation for employing computational techniques for ship trim optimization. PMID:24578649

Mouse natural killer cell development and maturation are differentially regulated by SHIP-1.

PubMed

Banh, Cindy; Miah, S M Shahjahan; Kerr, William G; Brossay, Laurent

2012-11-29

The SH2-containing inositol phosphatase-1 (SHIP-1) is a 5' inositol phosphatase known to negatively regulate the product of phosphoinositide-3 kinase (PI3K), phosphatidylinositol-3.4,5-trisphosphate. SHIP-1 can be recruited to a large number of inhibitory receptors expressed on natural killer (NK) cells. However, its role in NK cell development, maturation, and functions is not well defined. In this study, we found that the absence of SHIP-1 results in a loss of peripheral NK cells. However, using chimeric mice we demonstrated that SHIP-1 expression is not required intrinsically for NK cell lineage development. In contrast, SHIP-1 is required cell autonomously for NK cell terminal differentiation. These findings reveal both a direct and indirect role for SHIP-1 at different NK cell development checkpoints. Notably, SHIP-1-deficient NK cells display an impaired ability to secrete IFN-γ during cytokine receptor-mediated responses, whereas immunoreceptor tyrosine-based activation motif containing receptor-mediated responses is not affected. Taken together, our results provide novel insights on how SHIP-1 participates in the development, maturation, and effector functions of NK cells.

Ships going slow in reducing their NOx emissions: changes in 2005-2012 ship exhaust inferred from satellite measurements over Europe

NASA Astrophysics Data System (ADS)

Folkert Boersma, K.; Vinken, Geert C. M.; Tournadre, Jean

2015-07-01

We address the lack of temporal information on ship emissions, and report on rapid short-term variations of satellite-derived ship NOx emissions between 2005 and 2012 over European seas. Our inversion is based on OMI observed tropospheric NO2 columns and GEOS-Chem simulations. Average European ship NOx emissions increased by ˜15% from 2005 to 2008. This increase was followed by a reduction of ˜12% in 2009, a direct result of the global economic downturn in 2008-2009, and steady emissions from 2009 to 2012. Observations of ship passages through the Suez Canal and satellite altimeter derived ship densities suggests that ships in the Mediterranean Sea have reduced their speed by more than 30% since 2008. This reduction in ship speed is accompanied by a persistent 45% reduction of average, per ship NOx emission factors. Our results indicate that the practice of ‘slow steaming’, i.e. the lowering of vessel speed to reduce fuel consumption, has indeed been implemented since 2008, and can be detected from space. In spite of the implementation of slow steaming, one in seven of all NOx molecules emitted in Europe in 2012 originated from the shipping sector, up from one in nine in 2005. The growing share of the shipping contributions to the overall European NOx emissions suggests a need for the shipping sector to implement additional measures to reduce pollutant emissions at rates that are achieved by the road transport and energy producing sectors in Europe.

An Investigation on the Effects of Ship Sourced Emissions in Izmir Port, Turkey

PubMed Central

Saraçoğlu, Halil; Kılıç, Alper

2013-01-01

Maritime transportation is a major source of climate change and air pollution. Shipping emissions cause severe impacts on health and environment. These effects of emissions are emerged especially in territorial waters, inland seas, canals, straits, bays, and port regions. In this paper, exhaust gas emissions from ships in Izmir Port, which is one of the main ports in Turkey, are calculated by the ship activity-based methodology. Total emissions from ships in the port is estimated as 1923 ton y−1 for NOx, 1405 ton y−1 for SO2, 82753 ton y−1 for CO2, ton y−1 for HC, and 165 ton y−1 for PM in the year 2007. These emissions are classified regarding operation modes and types of ships. The results are compared with the other studies including amounts of exhaust pollutants generated by ships. According to the findings, it is clear that the ships calling the Izmir Port are important air polluting causes of the Izmir city and its surroundings. PMID:24198720

A Regulatory Role for Src Homology 2 Domain–Containing Inositol 5′-Phosphatase (Ship) in Phagocytosis Mediated by Fcγ Receptors and Complement Receptor 3 (αMβ2; Cd11b/Cd18)

PubMed Central

Cox, Dianne; Dale, Benjamin M.; Kashiwada, Masaki; Helgason, Cheryl D.; Greenberg, Steven

2001-01-01

The Src homology 2 domain–containing inositol 5′-phosphatase (SHIP) is recruited to immunoreceptor tyrosine-based inhibition motif (ITIM)–containing proteins, thereby suppressing phosphatidylinositol 3-kinase (PI 3-kinase)–dependent pathways. The role of SHIP in phagocytosis, a PI 3-kinase–dependent pathway, is unknown. Overexpression of SHIP in macrophages led to an inhibition of phagocytosis mediated by receptors for the Fc portion of IgG (FcγRs). In contrast, macrophages expressing catalytically inactive SHIP or lacking SHIP expression demonstrated enhanced phagocytosis. To determine whether SHIP regulates phagocytosis mediated by receptors that are not known to recruit ITIMs, we determined the effect of SHIP expression on complement receptor 3 (CR3; CD11b/CD18; αMβ2)–dependent phagocytosis. Macrophages overexpressing SHIP demonstrated impaired CR3-mediated phagocytosis, whereas macrophages expressing catalytically inactive SHIP demonstrated enhanced phagocytosis. CR3-mediated phagocytosis in macrophages derived from SHIP−/− mice was up to 2.5 times as efficient as that observed in macrophages derived from littermate controls. SHIP was localized to FcγR- and CR3-containing phagocytic cups and was recruited to the cytoskeleton upon clustering of CR3. In a transfected COS cell model of activation-independent CR3-mediated phagocytosis, catalytically active but not inactive SHIP also inhibited phagocytosis. We conclude that PI 3-kinase(s) and SHIP regulate multiple forms of phagocytosis and that endogenous SHIP plays a role in modulating β2 integrin outside-in signaling. PMID:11136821

Ship emission inventory and its impact on the PM2.5 air pollution in Qingdao Port, North China

NASA Astrophysics Data System (ADS)

Chen, Dongsheng; Wang, Xiaotong; Nelson, Peter; Li, Yue; Zhao, Na; Zhao, Yuehua; Lang, Jianlei; Zhou, Ying; Guo, Xiurui

2017-10-01

In this study, a first high temporal-spatial ship emission inventory in Qingdao Port and its adjacent waters has been developed using a ;bottom-up; method based on Automatic Identification System (AIS) data. The total estimated ship emissions for SO2, NOX, PM10, PM2.5, HC and CO in 2014 are 3.32 × 104, 4.29 × 104, 4.54 × 103, 4.18 × 103, 1.85 × 103 and 3.66 × 103 tonnes, respectively. Emissions of SO2 and NOX from ships account for 9% and 13% of the anthropogenic totals in Qingdao, respectively. The main contributors to the ship emissions are containers, followed by fishing ships, oil tankers and bulk carriers. The inter-monthly ship emissions varied significantly due to two reasons: stopping of the fishing ship activities during the fishing moratorium and the reduction of freight volume around the Chinese New Year Festival. Emissions from transport vessels concentrated basically along the shipping routes, while fishing ships contributed to massive irregular spatial emissions in the sea. The impact of ship emissions on the ambient air quality was further investigated using the Weather Research and Forecasting with Chemistry (WRF/Chem) model. The results reveal that the contribution of ship emissions to the PM2.5 concentrations in Qingdao is the highest in summer (13.1%) and the lowest in winter (1.5%). The impact was more evident over densely populated urban areas, where the contributions from ship emissions could be over 20% in July due to their close range to the docks. These results indicated that the management and control of the ship emissions are highly demanded considering their remarkable influence on the air quality and potential negative effects on human health.

Integrating Research on Global Climate Change and Human Use of the Oceans: a Geospatial Method for Daily Monitoring of Sea Ice and Ship Traffic in the Arctic

NASA Astrophysics Data System (ADS)

Eucker, W.; McGillivary, P. A.

2012-12-01

One apparent consequence of global climate change has been a decrease in the extent and thickness of Arctic sea ice more rapidly than models have predicted, while Arctic ship traffic has likewise increased beyond economic predictions. To ensure representative observations of changing climate conditions and human use of the Arctic Ocean, we concluded a method of tracking daily changes in both sea ice and shipping in the Arctic Ocean was needed. Such a process improves the availability of sea ice data for navigational safety and allows future developments to be monitored for understanding of ice and shipping in relation to policy decisions appropriate to optimize sustainable use of a changing Arctic Ocean. The impetus for this work was the 2009 Arctic Marine Shipping Assessment (AMSA) which provided baseline data on Arctic ship traffic. AMSA was based on responses from circumpolar countries, was manpower intensive, and took years to compile. A more timely method of monitoring human use of the Arctic Ocean was needed. To address this, a method of monitoring sea ice on a scale relevant to ship-navigation (<10km) was developed and implemented in conjunction with arctic ship tracking using S-AIS (Satellite Automatic Identification Systems). S-AIS is internationally required on ships over a certain size, which includes most commercial vessels in the Arctic Ocean. Daily AIS and sea ice observations were chosen for this study. Results of this method of geospatial analysis of the entire arctic are presented for a year long period from April 1, 2010 to March 31, 2011. This confirmed the dominance of European Arctic ship traffic. Arctic shipping is maximal during August and diminishes in September with a minimum in winter, although some shipping continues year-round in perennially ice-free areas. Data are analyzed for the four principal arctic quadrants around the North Pole by season for number and nationality of vessels. The goal of this study was not merely to monitor ship traffic and ice conditions concurrently, but also to demonstrate a new method of ocean monitoring based on daily assimilation, data fusion, and integrated visualization of satellite ice remote sensing data and S-AIS ship data. In the future, as Arctic ship traffic and cryosphere sea ice cover variability are both expected to increase, this method can provide near real-time physical data on global climate change and human dimensions of ocean use of to guide policies addressing arctic resource management, Search and Rescue (SAR) operations, oil spill response, and issues such as ship noise impacts on marine mammals, and whale-ship collision avoidance. An internationally agreed implementation of this methodology would benefit ships operating in the Arctic and advance sustainable use of the Arctic Ocean.

Construction of monitoring model and algorithm design on passenger security during shipping based on improved Bayesian network.

PubMed

Wang, Jiali; Zhang, Qingnian; Ji, Wenfeng

2014-01-01

A large number of data is needed by the computation of the objective Bayesian network, but the data is hard to get in actual computation. The calculation method of Bayesian network was improved in this paper, and the fuzzy-precise Bayesian network was obtained. Then, the fuzzy-precise Bayesian network was used to reason Bayesian network model when the data is limited. The security of passengers during shipping is affected by various factors, and it is hard to predict and control. The index system that has the impact on the passenger safety during shipping was established on basis of the multifield coupling theory in this paper. Meanwhile, the fuzzy-precise Bayesian network was applied to monitor the security of passengers in the shipping process. The model was applied to monitor the passenger safety during shipping of a shipping company in Hainan, and the effectiveness of this model was examined. This research work provides guidance for guaranteeing security of passengers during shipping.

Construction of Monitoring Model and Algorithm Design on Passenger Security during Shipping Based on Improved Bayesian Network

PubMed Central

Wang, Jiali; Zhang, Qingnian; Ji, Wenfeng

2014-01-01

A large number of data is needed by the computation of the objective Bayesian network, but the data is hard to get in actual computation. The calculation method of Bayesian network was improved in this paper, and the fuzzy-precise Bayesian network was obtained. Then, the fuzzy-precise Bayesian network was used to reason Bayesian network model when the data is limited. The security of passengers during shipping is affected by various factors, and it is hard to predict and control. The index system that has the impact on the passenger safety during shipping was established on basis of the multifield coupling theory in this paper. Meanwhile, the fuzzy-precise Bayesian network was applied to monitor the security of passengers in the shipping process. The model was applied to monitor the passenger safety during shipping of a shipping company in Hainan, and the effectiveness of this model was examined. This research work provides guidance for guaranteeing security of passengers during shipping. PMID:25254227

Design of integrated ship monitoring system using SAR, RADAR, and AIS

NASA Astrophysics Data System (ADS)

Yang, Chan-Su; Kim, Tae-Ho; Hong, Danbee; Ahn, Hyung-Wook

2013-06-01

When we talk about for the ship detection, identification and its classification, we need to go for the wide area of monitoring and it may be possible only through satellite based monitoring approach which monitors and covers coastal as well as the oceanic zone. Synthetic aperture radar (SAR) has been widely used to detect targets of interest with the advantage of the operating capability in all weather and luminance free condition (Margarit and Tabasco, 2011). In EU waters, EMSA(European Maritime Safety Agency) is operating the SafeSeaNet and CleanSeaNet systems which provide the current positions of all ships and oil spill monitoring information in and around EU waters in a single picture to Member States using AIS, LRIT and SAR images. In many countries, a similar system has been developed and the key of the matter is to integrate all available data. This abstract describes the preliminary design concept for an integration system of RADAR, AIS and SAR data for vessel traffic monitoring. SAR sensors are used to acquire image data over large coverage area either through the space borne or airborne platforms in UTC. AIS reports should be also obtained on the same date as of the SAR acquisition for the purpose to perform integration test. Land-based RADAR can provide ships positions detected and tracked in near real time. In general, SAR are used to acquire image data over large coverage area, AIS reports are obtained from ship based transmitter, and RADAR can monitor continuously ships for a limited area. In this study, we developed individual ship monitoring algorithms using RADAR(FMCW and Pulse X-band), AIS and SAR(RADARSAT-2 Full-pol Mode). We conducted field experiments two times for displaying the RADAR, AIS and SAR integration over the Pyeongtaek Port, South Korea.

2007 Expeditionary Warfare Conference (12th)

DTIC Science & Technology

2007-10-25

Ships 10 Joint High Speed Vessel (JHSV) Today • Program Capability – High speed lift ship capable of transporting cargo and personnel across...develop technologies that will: – Improve the capability to transfer cargo between Sea Base platforms – Provide for high speed / heavy lift...state actors for legitimacy and influence over the relevant population” Joint High Speed Vessel In-Service Amphibs LCAC & Ship to Shore

Oily Bilgewater Separators

DTIC Science & Technology

2011-11-01

International Convention for the Prevention of Pollution From Ships, 1973 as modified by the Protocol of 1978 (MARPOL 73/78). Under MARPOL, all ships...of oily bilgewater discharge from vessels are based on Annex I of the International Convention for the Prevention of Pollution from Ships, 1973 as...to the Convention . MARPOL includes six annexes, covering six categories of vessel discharges: oil (Annex I), noxious liquid substances (Annex II

A Decision Mixture Model-Based Method for Inshore Ship Detection Using High-Resolution Remote Sensing Images

PubMed Central

Bi, Fukun; Chen, Jing; Zhuang, Yin; Bian, Mingming; Zhang, Qingjun

2017-01-01

With the rapid development of optical remote sensing satellites, ship detection and identification based on large-scale remote sensing images has become a significant maritime research topic. Compared with traditional ocean-going vessel detection, inshore ship detection has received increasing attention in harbor dynamic surveillance and maritime management. However, because the harbor environment is complex, gray information and texture features between docked ships and their connected dock regions are indistinguishable, most of the popular detection methods are limited by their calculation efficiency and detection accuracy. In this paper, a novel hierarchical method that combines an efficient candidate scanning strategy and an accurate candidate identification mixture model is presented for inshore ship detection in complex harbor areas. First, in the candidate region extraction phase, an omnidirectional intersected two-dimension scanning (OITDS) strategy is designed to rapidly extract candidate regions from the land-water segmented images. In the candidate region identification phase, a decision mixture model (DMM) is proposed to identify real ships from candidate objects. Specifically, to improve the robustness regarding the diversity of ships, a deformable part model (DPM) was employed to train a key part sub-model and a whole ship sub-model. Furthermore, to improve the identification accuracy, a surrounding correlation context sub-model is built. Finally, to increase the accuracy of candidate region identification, these three sub-models are integrated into the proposed DMM. Experiments were performed on numerous large-scale harbor remote sensing images, and the results showed that the proposed method has high detection accuracy and rapid computational efficiency. PMID:28640236

A Decision Mixture Model-Based Method for Inshore Ship Detection Using High-Resolution Remote Sensing Images.

PubMed

Bi, Fukun; Chen, Jing; Zhuang, Yin; Bian, Mingming; Zhang, Qingjun

2017-06-22

With the rapid development of optical remote sensing satellites, ship detection and identification based on large-scale remote sensing images has become a significant maritime research topic. Compared with traditional ocean-going vessel detection, inshore ship detection has received increasing attention in harbor dynamic surveillance and maritime management. However, because the harbor environment is complex, gray information and texture features between docked ships and their connected dock regions are indistinguishable, most of the popular detection methods are limited by their calculation efficiency and detection accuracy. In this paper, a novel hierarchical method that combines an efficient candidate scanning strategy and an accurate candidate identification mixture model is presented for inshore ship detection in complex harbor areas. First, in the candidate region extraction phase, an omnidirectional intersected two-dimension scanning (OITDS) strategy is designed to rapidly extract candidate regions from the land-water segmented images. In the candidate region identification phase, a decision mixture model (DMM) is proposed to identify real ships from candidate objects. Specifically, to improve the robustness regarding the diversity of ships, a deformable part model (DPM) was employed to train a key part sub-model and a whole ship sub-model. Furthermore, to improve the identification accuracy, a surrounding correlation context sub-model is built. Finally, to increase the accuracy of candidate region identification, these three sub-models are integrated into the proposed DMM. Experiments were performed on numerous large-scale harbor remote sensing images, and the results showed that the proposed method has high detection accuracy and rapid computational efficiency.

Decadal evolution of ship emissions in China from 2004 to 2013 by using an integrated AIS-based approach and projection to 2040

NASA Astrophysics Data System (ADS)

Li, Cheng; Borken-Kleefeld, Jens; Zheng, Junyu; Yuan, Zibing; Ou, Jiamin; Li, Yue; Wang, Yanlong; Xu, Yuanqian

2018-05-01

Ship emissions contribute significantly to air pollution and pose health risks to residents of coastal areas in China, but the current research remains incomplete and coarse due to data availability and inaccuracy in estimation methods. In this study, an integrated approach based on the Automatic Identification System (AIS) was developed to address this problem. This approach utilized detailed information from AIS and cargo turnover and the vessel calling number information and is thereby capable of quantifying sectoral contributions by fuel types and emissions from ports, rivers, coastal traffic and over-the-horizon ship traffic. Based upon the established methodology, ship emissions in China from 2004 to 2013 were estimated, and those to 2040 at 5-year intervals under different control scenarios were projected. Results showed that for the area within 200 nautical miles (Nm) of the Chinese coast, SO2, NOx, CO, PM10, PM2.5, hydrocarbon (HC), black carbon (BC) and organic carbon (OC) emissions in 2013 were 1010, 1443, 118, 107, 87, 67, 29 and 21 kt yr-1, respectively, which doubled over these 10 years. Ship sources contributed ˜ 10 % to the total SO2 and NOx emissions in the coastal provinces of China. Emissions from the proposed Domestic Emission Control Areas (DECAs) within 12 Nm constituted approximately 40 % of the all ship emissions along the Chinese coast, and this percentage would double when the DECA boundary is extended to 100 Nm. Ship emissions in ports accounted for about one-quarter of the total emissions within 200 Nm, within which nearly 80 % of the emissions were concentrated in the top 10 busiest ports of China. SO2 emissions could be reduced by 80 % in 2020 under a 0.5 % global sulfur cap policy. In comparison, a similar reduction of NOx emissions would require significant technological change and would likely take several decades. This study provides solid scientific support for ship emissions control policy making in China. It is suggested to investigate and monitor the emissions from the shipping sector in more detail in the future.

Laboratory-based respiratory virus surveillance pilot project on select cruise ships in Alaska, 2013-15.

PubMed

Rogers, Kimberly B; Roohi, Shahrokh; Uyeki, Timothy M; Montgomery, David; Parker, Jayme; Fowler, Nisha H; Xu, Xiyan; Ingram, Deandra J; Fearey, Donna; Williams, Steve M; Tarling, Grant; Brown, Clive M; Cohen, Nicole J

2017-09-01

Influenza outbreaks can occur among passengers and crews during the Alaska summertime cruise season. Ill travellers represent a potential source for introduction of novel or antigenically drifted influenza virus strains to the United States. From May to September 2013-2015, the Alaska Division of Public Health, the Centers for Disease Control and Prevention (CDC), and two cruise lines implemented a laboratory-based public health surveillance project to detect influenza and other respiratory viruses among ill crew members and passengers on select cruise ships in Alaska. Cruise ship medical staff collected 2-3 nasopharyngeal swab specimens per week from passengers and crew members presenting to the ship infirmary with acute respiratory illness (ARI). Specimens were tested for respiratory viruses at the Alaska State Virology Laboratory (ASVL); a subset of specimens positive for influenza virus were sent to CDC for further antigenic characterization. Of 410 nasopharyngeal specimens, 83% tested positive for at least one respiratory virus; 71% tested positive for influenza A or B virus. Antigenic characterization of pilot project specimens identified strains matching predominant circulating seasonal influenza virus strains, which were included in the northern or southern hemisphere influenza vaccines during those years. Results were relatively consistent across age groups, recent travel history, and influenza vaccination status. Onset dates of illness relative to date of boarding differed between northbound (occurring later in the voyage) and southbound (occurring within the first days of the voyage) cruises. The high yield of positive results indicated that influenza was common among passengers and crews sampled with ARI. This finding reinforces the need to bolster influenza prevention and control activities on cruise ships. Laboratory-based influenza surveillance on cruise ships may augment inland influenza surveillance and inform control activities. However, these benefits should be weighed against the costs and operational limitations of instituting laboratory-based surveillance programs on ships. Published by Oxford University Press 2017. This work is written by [a] US Government employee[s] and is in the public domain in the US.

A simulation-based probabilistic design method for arctic sea transport systems

NASA Astrophysics Data System (ADS)

Martin, Bergström; Ove, Erikstad Stein; Sören, Ehlers

2016-12-01

When designing an arctic cargo ship, it is necessary to consider multiple stochastic factors. This paper evaluates the merits of a simulation-based probabilistic design method specifically developed to deal with this challenge. The outcome of the paper indicates that the incorporation of simulations and probabilistic design parameters into the design process enables more informed design decisions. For instance, it enables the assessment of the stochastic transport capacity of an arctic ship, as well as of its long-term ice exposure that can be used to determine an appropriate level of ice-strengthening. The outcome of the paper also indicates that significant gains in transport system cost-efficiency can be obtained by extending the boundaries of the design task beyond the individual vessel. In the case of industrial shipping, this allows for instance the consideration of port-based cargo storage facilities allowing for temporary shortages in transport capacity and thus a reduction in the required fleet size / ship capacity.

Modeling the Impact of Arctic Shipping Pollution on Air Quality off the Coast of Northern Norway

NASA Astrophysics Data System (ADS)

Thomas, J. L.; Law, K.; Marelle, L.; Raut, J.; Jalkanen, J.; Johansson, L.; Roiger, A.; Schlager, H.; Kim, J.; Reiter, A.; Weinzierl, B.; Rose, M.; Fast, J. D.

2013-12-01

As the Arctic is undergoing rapid and potentially irreversible changes, such as the shrinking and thinning of sea-ice cover, the levels of atmospheric pollution are expected to rise dramatically due to the emergence of local pollution sources including shipping. Shipping routes through the Arctic (such as Russia's Northern Sea Route) are already used as an alternative to the traditional global transit shipping routes. In summer 2012, the ACCESS (Arctic Climate Change, Economy, and Society) aircraft campaign focused on studying pollution sources off the coast of northern Norway to quantify emissions from shipping and other anthropogenic pollution sources. To complement these measurements, a regional chemical transport model is used to study the impact of shipping pollution on gas and aerosol concentrations in the region. WRF-Chem (The Weather Research and Forecasting Model with Chemistry, which simulates gas and aerosols simultaneously with meteorology) is run with real time shipping emissions from STEAM (Ship Traffic Emission Assessment Model) for July 2012. The STEAM model calculates gas and aerosol emissions of marine traffic based on the ship type and location provided by the Automatic Identification System (AIS). Use of real time position, speed, and ship specific information allows for development of emissions with very high spatial (1x1 km) and temporal (30 min) resolution, which are used in the regional model runs. STEAM emissions have been specifically generated for shipping off the coast of Norway during the entire ACCESS campaign period. Simulated ship plumes from high-resolution model runs are compared to aircraft measurements. The regional impact of current summertime shipping is also examined. At present, relatively light ship traffic off the coast of northern Norway results in only a small impact of shipping pollution on regional atmospheric chemistry. The impact of increased future shipping on regional atmospheric chemistry is also assessed.

Emission-factor uncertainties in maritime transport in the Strait of Gibraltar, Spain

NASA Astrophysics Data System (ADS)

Moreno-Gutiérrez, J.; Durán-Grados, V.; Uriondo, Z.; Ángel Llamas, J.

2012-08-01

A reliable and up-to-date maritime emission inventory is essential for atmospheric scientists quantifying the impact of shipping. The objective of this study is to estimate the atmospheric emissions of SO2, NOx, CO2 and PM10 by international merchant shipping in 2007 in the Strait of Gibraltar, Spain, including the Algeciras Bay by two methods. Two methods (both bottom-up) have been used in this study: 1. Establishing engine power-based emission factors (g kWh-1, EPA) or the mass of pollutant per work performed by the engine for each of the relevant components of the exhaust gas from diesel engines and power for each ship. 2. Establishing fuel-based emission factors (kg emitted/t of fuel) or mass of pollutant per mass of combusted fuel for each of the relevant components of the exhaust gas and a fuel-consumption inventory (IMO). In both methods, the means to estimate engine power and fuel-consumption inventories are the same. The exhaust from boilers and incinerators is regarded as a small contributor and excluded. In total, an estimated average of 1 389 111.05 t of CO2, 23 083.09 t of SO2, 32 005.63 t of NOx and 2972 t of PM10 were emitted from January 2007 until December 2007 by international and domestic shipping. The estimated total fuel consumption amounts to 437 405.84 t. The major differences between the estimates generated by the two methods are for NOx (16% in certain cases) and CO (up to 23%). A total difference for all compounds of 3038 t (approximately 2%) has been found between the two methods but it is not areasonable estimate of uncertainty. Therefore, the results for both methods may be considered acceptable because the actual uncontrolled deviations appear in the changes in emission factors that occur for a given engine with age. These deviations are often difficult to quantify and depend on individual shipboard service and maintenance routines. Emission factors for CO and NOx are not constant and depend on engine condition. For example, tests conducted by the authors of this paper demonstrate that when an engine operates under normal in-service conditions, the emissions are within limits. However, with a small fault in injection timing, the NOx emission exceeds the limits (30% higher value in some cases). A fault in the maintenance of the injection nozzles increases the CO emission (15% higher value in some cases).

Decarbonizing the international shipping industry: Solutions and policy recommendations.

PubMed

Wan, Zheng; El Makhloufi, Abdel; Chen, Yang; Tang, Jiayuan

2018-01-01

Ship-source greenhouse gas (GHG) emissions could increase by up to 250% by 2050 from their 2012 levels, owing to increasing global freight volumes. Binding international legal agreements to regulate GHGs, however, are lacking as technical solutions remain expensive, and crucial industrial support is absent. In 2003, the International Maritime Organization adopted Resolution A.963 (23) to regulate shipping CO 2 emissions via technical, operational, and market-based routes. However, progress has been slow and uncertain; there is no concrete emission reduction target or definitive action plan. Yet, a full-fledged roadmap may not even emerge until 2023. In this policy analysis, we revisit the progress of technical, operational, and market-based routes and the associated controversies. We argue that 1) a performance-based index, though good-intentioned, has loopholes affecting meaningful CO 2 emission reductions driven by technical advancements; 2) using slow steaming to cut energy consumption stands out among all operational solutions thanks to its immediate and obvious results, but with the already slow speed in practice, this single source has limited emission reduction potential; 3) without a technology-savvy shipping industry, a market-based approach is essentially needed to address the environmental impact. To give shipping a 50:50 chance for contributing fairly and proportionately to keep global warming below 2°C, deep emission reductions should occur soon. Copyright © 2017 Elsevier Ltd. All rights reserved.

Optimization of the Costs and the Safety of Maritime Transport by Routing: The use of Currents Forecast in the Routing of Racing Sail Boats as a Prototype of Rout Optimization for Trading Ships

NASA Astrophysics Data System (ADS)

Theunynck, Denis; Peze, Thierry; Toumazou, Vincent; Zunquin, Gauthier; Cohen, Olivier; Monges, Arnaud

2005-03-01

It is interesting to see whether the model of routing designed for races and great Navy operations could be transferred to commercial navigation and if so, within which framework.Sail boat routing conquered its letters of nobility during great races like the « Route du Rhum » or the transatlantic race « Jacques Vabre ». It is the ultimate stage of the step begun by the Navy at the time of great operations, like D-day (Overlord )June 6, 1944, in Normandy1.Routing is, from the beginning, mainly based on statistical knowledge and weather forecast, but with the recent availability of reliable currents forecast, sail boats routers and/or skippers now have to learn how to use both winds and currents to obtain the best performance, that is to travel between two points in the shortest time possible in acceptable security conditions.Are the currents forecast only useful to racing sail boat ? Of course not, they are a great help to fisherman for whom the knowledge of currents is also the knowledge of sea temperature who indicates the probability of fish presence. They are also used in offshore work to predict the hardness of the sea during operation.A less developed field of application is the route optimization of trading ships. The idea is to optimize the use of currents to increase the relative speed of ships with no augmentation of fuel expense. This new field will require that currents forecasters learn about the specific needs of another type of clients. There is also a need of teaching because the future customers will have to learn how to use the information they will get.At this point, the introduction of the use of currents forecast in racing sail boats routing is only the first step. It is of great interest because it can rely on a high knowledge in routing.The main difference is of course that the wind direction and its force are of greater importance to a sail boat that they are for a trading ship for whom the point of interest will be the fuel consumption and the ETA respect.Despite that, sail boat routing could be use as a prototype to determine the needs, both in term of information and formations of ship routers and skippers2.

Aeroelastic Modeling of Offshore Turbines and Support Structures in Hurricane-Prone Regions (Poster)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Damiani, R.

US offshore wind turbines (OWTs) will likely have to contend with hurricanes and the associated loading conditions. Current industry standards do not account for these design load cases (DLCs), thus a new approach is required to guarantee that the OWTs achieve an appropriate level of reliability. In this study, a sequentially coupled aero-hydro-servo-elastic modeling technique was used to address two design approaches: 1.) The ABS (American Bureau of Shipping) approach; and 2.) The Hazard Curve or API (American Petroleum Institute) approach. The former employs IEC partial load factors (PSFs) and 100-yr return-period (RP) metocean events. The latter allows setting PSFsmore » and RP to a prescribed level of system reliability. The 500-yr RP robustness check (appearing in [2] and [3] upcoming editions) is a good indicator of the target reliability for L2 structures. CAE tools such as NREL's FAST and Bentley's' SACS (offshore analysis and design software) can be efficiently coupled to simulate system loads under hurricane DLCs. For this task, we augmented the latest FAST version (v. 8) to include tower aerodynamic drag that cannot be ignored in hurricane DLCs. In this project, a 6 MW turbine was simulated on a typical 4-legged jacket for a mid-Atlantic site. FAST-calculated tower base loads were fed to SACS at the interface level (transition piece); SACS added hydrodynamic and wind loads on the exposed substructure, and calculated mudline overturning moments, and member and joint utilization. Results show that CAE tools can be effectively used to compare design approaches for the design of OWTs in hurricane regions and to achieve a well-balanced design, where reliability levels and costs are optimized.« less

Emission inventories for ships in the Arctic based on satellite sampled AIS data

NASA Astrophysics Data System (ADS)

Christensen, J. H.; Winther, M.; Plejdrup, M. S.; Ravn, E. S.; Eriksson, O. M.; Kristensen, H. O.

2013-12-01

Emissions from ships inside Arctic are an important source of the Arctic pollution as e.g. SO2, NOx and Black Carbon (BC). This paper presents a detailed BC, NOx and SO2 emission inventory for ships in the Arctic for the year 2012 based on satellite AIS data, ship engine power functions and technology stratified emission factors. Emission projections are presented for the years 2020, 2030 and 2050 combined with emission from polar diversion routes as given by Corbett et al. (2010). Furthermore the Danish Eulerian Hemispheric Model (Christensen, 1997; Brandt et al., 2012), which is 3-d Chemical Transport Model covering the Northern hemisphere was use to study the transport of BC, SO2 and O3 and estimate BC deposition results in order to study then current and future contribution from Arctic ship traffics to atmospheric concentrations and deposition of pollutants in the Arctic. In 2012, the largest emission contributions of Artic ships emissions are from fishing ships (45% for BC, 38% for NOx and 23% for SO2) followed by passenger ships (20%, 17%, 25%), tankers (9%, 13%, 15%), general cargo (8%, 11%, 12%) and container ships (5%, 7%, 8%). Without diverted traffic from 2012 to 2050 the total BC, NOx and SO2 emissions are expected to change by 16 %, -32 % and -63 %, respectively. For the year 2012 the average calculated contributions for ships of BC, SO, and O3 concentrations and BC deposition become low and similar for the emissions projections without diverted traffic of the years 2020, 2030 and 2050, but with diverted traffic the contributions for ships to the BC, SO, and O3 concentrations and BC deposition becomes significantly higher especially for the year 2050 and especially during the summer season over the areas, where the diverted traffic are assumed to occur. These high forecasted values for BC sea-ice deposition close to the Polar routes are of main concern due to decreases in the albedo which in turn enhances the melting of sea-ice.

Significance of Waterway Navigation Positioning Systems On Ship's Manoeuvring Safety

NASA Astrophysics Data System (ADS)

Galor, W.

The main goal of navigation is to lead the ship to the point of destination safety and efficiently. Various factors may affect ship realisating this process. The ship movement on waterway are mainly limited by water area dimensions (surface and depth). These limitations cause the requirement to realise the proper of ship movement trajectory. In case when this re requirement cant't fulfil then marine accident may happend. This fact is unwanted event caused losses of human health and life, damage or loss of cargo and ship, pollution of natural environment, damage of port structures or blocking the port of its ports and lost of salvage operation. These losses in same cases can be catas- trophical especially while e.i. crude oil spilling could be place. To realise of safety navigation process is needed to embrace the ship's movement trajectory by waterways area. The ship's trajectory is described by manoeuvring lane as a surface of water area which is require to realise of safety ship movement. Many conditions affect to ship manoeuvring line. The main are following: positioning accuracy, ship's manoeuvring features and phenomena's of shore and ship's bulk common affecting. The accuracy of positioning system is most important. This system depends on coast navigation mark- ing which can range many kinds of technical realisation. Mainly used systems based on lights (line), radionavigation (local system or GPS, DGPS), or radars. If accuracy of positiong is higer, then safety of navigation is growing. This article presents these problems exemplifying with approaching channel to ports situated on West Pomera- nian water region.

Work related mortality among merchant seafarers employed in UK Royal Fleet Auxillary shipping from 1976 to 2005.

PubMed

Roberts, Stephen E; Marlow, Peter B

2006-01-01

Over 2300 merchant seafarers are currently employed on board UK Royal Fleet Auxiliary (RFA) ships. However, little is known about work related mortality among these seafarers, and whether it is lower than among seafarers in merchant fleets. To establish the causes and circumstances of all work related deaths among seafarers who were employed in RFA ships from 1976 to 2005, to compare mortality rates with those in other merchant fleets, and to identify implications for maritime health. A population based study of work related mortality over 30 years. A total of 60 deaths among seafarers in RFA ships were caused by disease (30), accidents (19), suicide (6), homicide (one), and inconclusive causes (4). Six of the 19 fatal accidents were directly related to work duties (occupational accidents), 12 occurred during off-duty time and one resulted from a shipping disaster. The fatal accident rate was about one half, and the fatal work related accident rate was about one quarter, of corresponding rates in UK merchant shipping from 1976-2002; and they were much lower than those in merchant fleets internationally. The fatal accident rate in RFA shipping also fell by about 80% over the 30 year study period. The lower fatal accident rates in RFA shipping, particularly for work related accidents, presumably reflect a lower incidence of hazardous working practices, arising from better training and career pathways for seafarers in RFA shipping, as well as better maintained ships with higher manning levels than in merchant shipping.

Military Readiness: Progress and Challenges in Implementing the Navy’s Optimized Fleet Response Plan

DTIC Science & Technology

2016-05-02

deployments for sailors and for the ship repair industrial base. They have also resulted in declining ship conditions across the fleet, and have...at shipyards.2 This report also describes Navy and industry officials’ perspectives on the impact that Navy installation and personnel security...and we interviewed officials at public and private shipyards involved in maintaining Navy ships. Additionally, we interviewed Navy and industry

Inventory Funding Methods on Navy Ships: NWCF vs. End-use

DTIC Science & Technology

2013-06-01

OPTAR Operating Target OSO Other Supply Officer POM Pre/Post-Overseas Movement R-Supply Relational Supply RoR Reorder Review SAC Service...process called other supply officer ( OSO ) transfer. Since end-use ships own their inventory, the supply officer can choose to transfer a part being...requested by another ship at their discretion, based on their ship’s anticipated requirements and their own goodwill. OSO transfers among end-use

Removing the regional level from the Niger vaccine supply chain.

PubMed

Assi, Tina-Marie; Brown, Shawn T; Kone, Souleymane; Norman, Bryan A; Djibo, Ali; Connor, Diana L; Wateska, Angela R; Rajgopal, Jayant; Slayton, Rachel B; Lee, Bruce Y

2013-06-10

Since many of the world's vaccine supply chains contain multiple levels, the question remains of whether removing a level could bring efficiencies. We utilized HERMES to generate a detailed discrete-event simulation model of Niger's vaccine supply chain and compared the current four-tier (central, regional, district, and integrated health center levels) with a modified three-tier structure (removing the regional level). Different scenarios explored various accompanying shipping policies and frequencies. Removing the regional level and implementing a collection-based shipping policy from the district stores increases vaccine availability from a mean of 70-100% when districts could collect vaccines at least weekly. Alternatively, implementing a delivery-based shipping policy from the central store monthly in three-route and eight-route scenarios only increases vaccine availability to 87%. Restricting central-to district vaccine shipments to a quarterly schedule for three-route and eight-route scenarios reduces vaccine availability to 49%. The collection-based shipping policy from district stores reduces supply chain logistics cost per dose administered from US$0.14 at baseline to US$0.13 after removing the regional level. Removing the regional level from Niger's vaccine supply chain can substantially improve vaccine availability as long as certain concomitant adjustments to shipping policies and frequencies are implemented. Copyright © 2013 Elsevier Ltd. All rights reserved.

Removing the Regional Level from the Niger Vaccine Supply Chain

PubMed Central

Assi, Tina-Marie; Brown, Shawn T.; Kone, Souleymane; Norman, Bryan A.; Djibo, Ali; Connor, Diana L.; Wateska, Angela R.; Rajgopal, Jayant; Slayton, Rachel B.; Lee, Bruce Y.

2013-01-01

Objective Since many of the world’s vaccine supply chains contain multiple levels, the question remains of whether removing a level could bring efficiencies. Methods We utilized HERMES to generate a detailed discrete-event simulation model of Niger’s vaccine supply chain and compare the current four-tier (central, regional, district and integrated health center levels) with a modified three-tier structure (removing the regional level). Different scenarios explored various accompanying shipping policies and frequencies. Findings Removing the regional level and implementing a collection-based shipping policy from the district stores increases vaccine availability from a mean of 70% to 100% when districts could collect vaccines at least weekly. Alternatively, implementing a delivery-based shipping policy from the central store monthly in three-route and eight-route scenarios only increases vaccine availability to 87%. Restricting central-to district vaccine shipments to a quarterly schedule for three-route and eight-route scenarios reduces vaccine availability to 49%. The collection-based shipping policy from district stores reduces supply chain logistics cost per dose administered from US$0.14 at baseline to US$0.13 after removing the regional level. Conclusion Removing the regional level from Niger’s vaccine supply chain can substantially improve vaccine availability as long as certain concomitant adjustments to shipping policies and frequencies are implemented. PMID:23602666

Offshore safety case approach and formal safety assessment of ships.

PubMed

Wang, J

2002-01-01

Tragic marine and offshore accidents have caused serious consequences including loss of lives, loss of property, and damage of the environment. A proactive, risk-based "goal setting" regime is introduced to the marine and offshore industries to increase the level of safety. To maximize marine and offshore safety, risks need to be modeled and safety-based decisions need to be made in a logical and confident way. Risk modeling and decision-making tools need to be developed and applied in a practical environment. This paper describes both the offshore safety case approach and formal safety assessment of ships in detail with particular reference to the design aspects. The current practices and the latest development in safety assessment in both the marine and offshore industries are described. The relationship between the offshore safety case approach and formal ship safety assessment is described and discussed. Three examples are used to demonstrate both the offshore safety case approach and formal ship safety assessment. The study of risk criteria in marine and offshore safety assessment is carried out. The recommendations on further work required are given. This paper gives safety engineers in the marine and offshore industries an overview of the offshore safety case approach and formal ship safety assessment. The significance of moving toward a risk-based "goal setting" regime is given.

Ship Detection from Ocean SAR Image Based on Local Contrast Variance Weighted Information Entropy

PubMed Central

Huang, Yulin; Pei, Jifang; Zhang, Qian; Gu, Qin; Yang, Jianyu

2018-01-01

Ship detection from synthetic aperture radar (SAR) images is one of the crucial issues in maritime surveillance. However, due to the varying ocean waves and the strong echo of the sea surface, it is very difficult to detect ships from heterogeneous and strong clutter backgrounds. In this paper, an innovative ship detection method is proposed to effectively distinguish the vessels from complex backgrounds from a SAR image. First, the input SAR image is pre-screened by the maximally-stable extremal region (MSER) method, which can obtain the ship candidate regions with low computational complexity. Then, the proposed local contrast variance weighted information entropy (LCVWIE) is adopted to evaluate the complexity of those candidate regions and the dissimilarity between the candidate regions with their neighborhoods. Finally, the LCVWIE values of the candidate regions are compared with an adaptive threshold to obtain the final detection result. Experimental results based on measured ocean SAR images have shown that the proposed method can obtain stable detection performance both in strong clutter and heterogeneous backgrounds. Meanwhile, it has a low computational complexity compared with some existing detection methods. PMID:29652863

[Psychopathology service on ships].

PubMed

Nowosielski, Radosław; Mazurek, Tomasz; Florkowski, Antoni

2010-06-01

The aim of this study was to describe the specific engineering services and suitability of candidates for the psychophysical performance. Navy ships are equipped with equipment and weapons are controlled by electronic devices ship and crew. Advanced technology puts high demands on operator. For the ship's staff are recruited soldiers of the psychophysical characteristics predisposing to this kind of action. The paper uses personal experience to work in military units of the Navy, and data from the literature. Terms of sailing ships off the summer season are defined as difficult. The crew during a combat mission felt the risks associated with movements of the ship in difficult meteorological conditions, and associated with the implementation of the task. The development of ship's technical equipment, working in isolated groups, functioning within a limited space, noise, vibration, electromagnetic waves heighten the emotional burden on crew members. Military service on Navy ships require high psycho-physical predisposition, resistance to stress. The crucial factor is proper selection among the candidates based on psychiatric and psychological counseling for military and medical jurisprudence. Also plays a significant role for training doctors and specialists in psychoprophylaxy of military units in the field of mental hygiene.

Impact of a nitrogen emission control area (NECA) for ship traffic on the future air quality in the Baltic Sea region

NASA Astrophysics Data System (ADS)

Karl, Matthias; Geyer, Beate; Bieser, Johannes; Matthias, Volker; Quante, Markus; Jalkanen, Jukka-Pekka; Johansson, Lasse; Fridell, Erik

2017-04-01

Deposition of nitrogen compounds originating from shipping activities contribute to eutrophication of the Baltic Sea and coastal areas in the Baltic Sea region. Emissions of nitrogen oxides (NOx) from shipping on the Baltic Sea are comparable to the combined land-based emissions of NOx from Finland and Sweden and have been relatively stable over the last decade. However, expected future growth of maritime transport will result in higher fuel consumption and, if not compensated by increased transport efficiency or other measures, lead to higher total emissions of NOx from shipping. For the Baltic Sea a nitrogen emission control area (NECA) will become effective in 2021 - permitting only new built ships that are compliant with stringent Tier III emission limits - with the target of reducing NOx-emissions. In order to study the effect of implementing a Baltic Sea NECA-2021 on air quality and nitrogen deposition two future scenarios were designed; one with implementation of a NECA for the Baltic Sea starting in 2021 and another with no NECA implemented. The same increase of ship traffic was assumed for both future scenarios. Since complete fleet renewal with low NOx-emitting engines is not expected until 20-30 years after the NECA entry date, year 2040 was chosen as future scenario year. The Community Multiscale Air Quality (CMAQ) model was used to simulate the current and future air quality situation. The nested simulation runs with CMAQ were performed on a horizontal resolution of 4 km × 4 km for the entire Baltic Sea region. The meteorological year 2012 was chosen for the simulation of the current and future air quality situation since the 2m-temperature and precipitation anomalies of 2012 are closely aligned to the 2004-2014 decadal average over Baltic Proper. High-resolution meteorology obtained from COSMO-CLM was used for the regional simulations. Ship emissions were generated with the Ship Traffic Emission Assessment Model (STEAM) by the Finnish Meteorological Institute (FMI) using the Automatic Identification System (AIS) network data to allocate ship positions. Gridded land-based emissions were taken from the SMOKE-EU model which is based on the official EMEP data. Future land-based emissions were reduced in accordance with current legislation. Model simulations for the current situation show that shipping emissions are the main contributor to ambient NO2 concentrations over the Baltic Sea. Shipping emissions are responsible for 40-70 % of the particulate nitrate concentrations during the summer months. Relative contribution of shipping emissions to monthly total nitrogen deposition, as a sum of oxidized and reduced nitrogen compounds, was highest in summer, with up to 60 % in the northern part of the Baltic Proper, while it was on average 10 % for other parts of the Baltic Sea. With the NECA in the Baltic Sea in effect from 2021, the reduction of reactive nitrogen concentrations and deposition in the Baltic Sea region compared to a scenario without Tier III regulations is significant.

10. Storage and shipping container, ballistic missile, mounted on ballistic ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. Storage and shipping container, ballistic missile, mounted on ballistic missile trailer, view from left front - Ellsworth Air Force Base, Delta Flight, 10 mile radius around Exit 127 off Interstate 90, Interior, Jackson County, SD

11. Storage and shipping container, ballistic missile, mounted on ballistic ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

11. Storage and shipping container, ballistic missile, mounted on ballistic missile trailer, view from left side - Ellsworth Air Force Base, Delta Flight, 10 mile radius around Exit 127 off Interstate 90, Interior, Jackson County, SD

Ship cabin leakage alarm based on ARM SCM

NASA Astrophysics Data System (ADS)

Qu, Liyan

2018-03-01

If there is a leakage in the cabin of a sailing ship, it is a major accident that threatens the personnel and property of the ship. If we can’t take timely measures, there will be a devastating disaster. In order to judge the leakage of the cabin, it is necessary to set up a leakage alarm system, so as to achieve the purpose of detecting and alarming the leakage of the cabin, and avoid the occurrence of accidents. This paper discusses the design of ship cabin leakage alarm system based on ARM SCM. In order to ensure the stability and precision of the product, the hardware design of the alarm system is carried out, such as circuit design, software design, the programming of SCM, the software programming of upper computer, etc. It is hoped that it can be of reference value to interested readers.

NASA's Ship-Aircraft Bio-Optical Research (SABOR)

NASA Image and Video Library

2014-08-25

Fixing the "Fish" On July 19, 2014, Wayne Slade of Sequoia Scientific, and Allen Milligan of Oregon State University, made adjustments to the "fish" that researchers used to hold seawater collected from a depth of about 3 meters (10 feet) while the ship was underway. NASA's Ship-Aircraft Bio-Optical Research (SABOR) experiment is a coordinated ship and aircraft observation campaign off the Atlantic coast of the United States, an effort to advance space-based capabilities for monitoring microscopic plants that form the base of the marine food chain. Read more: 1.usa.gov/WWRVzj Credit: NASA/SABOR/Wayne Slade, Sequoia Scientific .NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

Shale Gas Information Platform SHIP: first year of fact-based communication

NASA Astrophysics Data System (ADS)

Hübner, Andreas; Horsfield, Brian; Petrow, Theresia

2013-04-01

Natural gas produced from shale, already on stream in the USA, and under development in many regions worldwide, has brought about a fundamental change in energy resource distribution and energy politics. According to recent IEA publications, shale gas production will continue to rise globally and will be embraced by many more countries than at present. Shale gas production, especially in densely populated regions, brings with it a new dimension of risk alongside potential benefits. A fact-based discussion of the pros and cons, however, has been hampered in part by a scarcity of scientific knowledge on the related risks, and by a lack of appropriate, i.e. transparent and balanced, communication of the academic research perspective. With the Shale Gas Information Platform SHIP, the GFZ German Research Centre for Geosciences engages in the public discussion of technical and environmental issues related to shale gas exploration and production. The project was launched online in early 2012, at a propitious time: the public debate was until then dominated by voices from industry and from environmental groups, which were often biased and/or lacking sound factual background. Significant academic research on the risks related to shale gas development and hydraulic fracturing operations in particular only started in 2011 and continued to expand in 2012. This was reflected in an increased output of peer-reviewed publications and academic reports. SHIP puts these into perspective and brings them to the attention of the broader public. With just one year of online presence, SHIP has already effectively filled the void in fact-based information on shale gas. This can be seen by a continuing demand for subscriptions to our News Email Alert Service, and by invitations SHIP has received to conferences and workshops, in order to share our experience of science-based and balanced information dissemination. SHIP's web content is expanding and so is its expert network. Collaborations with large research initiatives, such as GASH Gas Shales in Europe (GFZ Potsdam), ReFINE - Researching Fracking IN Europe (Durham University) and the US EPA Gas STAR program ensuring up to date information is disseminated. However, the issue of shale gas is much discussed by local residents in potential exploration areas in Europe and elsewhere, and sound information becomes more scarce outside the English language domain. To remedy this shortcoming, large parts of SHIP content are translated to German and Polish; two countries where shale gas development is a hot topic on the political agenda. In the course of development of the SHIP initiative, other languages may follow. SHIP seeks to grow continuously, and a conference like EGÚs General Assembly is very well suited to spread the word. If you are interested to contribute/collaborate, please contact SHIP.

Journal of the British Ship Research Association. Index to Volume 34, January to December 1979. Abstracts Number 49, 883-52, 042.

DTIC Science & Technology

1979-01-01

ENERGY ABSORPTION CAPACITY 50083 MODEL TESTS: 51101 OF TANKERS 52034 POLLUTION PROBLEMS: 51678 SAFETY PRECAUTIONS 50019 SIMULATION OF MODEL TESTS 50257...PREVENTION METHODS 50375 PROTECTION AGAINST: PIPEWORK: 51649 TANKS: 51649 RESISTANCE TO: IN MARINE SYSTEMS . 50179 SALT-WATER 52004 CORROSION...STANDARDISED 50550 DIESEL ENGINES: 51961 309-KW 50051 9DKRM84/180-3 •• 50049 ADVANCED STRENGTH ANA’,YSIS METHOD TO IMPROVE RELIABILITY OF CYLI- NDER COVER

The circular form of the linear superconducting machine for marine propulsion

NASA Astrophysics Data System (ADS)

Rakels, J. H.; Mahtani, J. L.; Rhodes, R. G.

1981-01-01

The superconducting linear synchronous machine (LSM) is an efficient method of propulsion of advanced ground transport systems and can also be used in marine engineering for the propulsion of large commercial vessels, tankers, and military ships. It provides high torque at low shaft speeds and ease of reversibility; a circular LSM design is proposed as a drive motor. The equipment is compared with the superconducting homopolar motors, showing flexibility in design, built in redundancy features, and reliability.

Helicopter Reliability and Maintainability Trends during Development and Production.

DTIC Science & Technology

1981-07-01

engine entry (the T-53) showed improvement in successive models. For helicopters, we have mixed results: some improved (YUH-60A, CH-47, UH-lD, AH-IG...understand the linkage between R&M program goals and life cycle costs, however, it is necessary to understand-- (1) what resource levels are required during...attributes of the system; (3) how those field attributes affect the cost of owner- ship of the system; and (4) whether or not, and at what cost, R&M values

Contribution of ship emissions to the concentration and deposition of air pollutants in Europe

NASA Astrophysics Data System (ADS)

Aksoyoglu, S.; Prévôt, A. S. H.; Baltensperger, U.

2015-11-01

Emissions from the marine transport sector are one of the least regulated anthropogenic emission sources and contribute significantly to air pollution. Although strict limits were introduced recently for the maximum sulfur content in marine fuels in the SECAs (sulfur emission control areas) and in the EU ports, sulfur emissions outside the SECAs and emissions of other components in all European maritime areas have continued to increase in the last two decades. We have used the air quality model CAMx with and without ship emissions for the year 2006 to determine the effects of international shipping on the annual as well as seasonal concentrations of ozone, primary and secondary components of PM2.5 and the dry and wet deposition of nitrogen and sulfur compounds in Europe. Our results suggest that emissions from international shipping affect the air quality in northern and southern Europe differently and their contributions to the air concentrations vary seasonally. The largest changes in pollutant concentrations due to ship emissions were predicted for summer. Increased concentrations of the primary particle mass were found only along the shipping routes whereas concentrations of the secondary pollutants were affected over a larger area. Concentrations of particulate sulfate increased due to ship emissions in the Mediterranean (up to 60 %), in the English Channel and the North Sea (30-35 %) while increases in particulate nitrate levels were found especially in the north, around the Benelux area (20 %) where there were high NH3 land-based emissions. Our model results showed that not only the atmospheric concentrations of pollutants are affected by ship emissions, but also depositions of nitrogen and sulfur compounds increase significantly along the shipping routes. NOx emissions from the ships especially in the English Channel and the North Sea, cause a decrease in the dry deposition of reduced nitrogen at source regions by moving it from the gas-phase to the particle phase which then contributes to an increase in the wet deposition at coastal areas with higher precipitation. In the western Mediterranean region on the other hand, model results show an increase in the deposition of oxidized nitrogen (mostly HNO3) due to the ship traffic. Dry deposition of SO2 seems to be significant along the shipping routes whereas sulfate wet deposition occurs mainly along the Scandinavian and Adriatic coasts. The results presented in this paper suggest that evolution of NOx emissions from ships and land-based NH3 emissions will play a significant role in the future European air quality.

A method of inferring collision ratio based on maneuverability of own ship under critical collision conditions

NASA Astrophysics Data System (ADS)

You, Youngjun; Rhee, Key-Pyo; Ahn, Kyoungsoo

2013-06-01

In constructing a collision avoidance system, it is important to determine the time for starting collision avoidance maneuver. Many researchers have attempted to formulate various indices by applying a range of techniques. Among these indices, collision risk obtained by combining Distance to the Closest Point of Approach (DCPA) and Time to the Closest Point of Approach (TCPA) information with fuzzy theory is mostly used. However, the collision risk has a limit, in that membership functions of DCPA and TCPA are empirically determined. In addition, the collision risk is not able to consider several critical collision conditions where the target ship fails to take appropriate actions. It is therefore necessary to design a new concept based on logical approaches. In this paper, a collision ratio is proposed, which is the expected ratio of unavoidable paths to total paths under suitably characterized operation conditions. Total paths are determined by considering categories such as action space and methodology of avoidance. The International Regulations for Preventing Collisions at Sea (1972) and collision avoidance rules (2001) are considered to solve the slower ship's dilemma. Different methods which are based on a constant speed model and simulated speed model are used to calculate the relative positions between own ship and target ship. In the simulated speed model, fuzzy control is applied to determination of command rudder angle. At various encounter situations, the time histories of the collision ratio based on the simulated speed model are compared with those based on the constant speed model.

Policy Decisions for Strategic Shipyard Survival

DTIC Science & Technology

1992-12-01

a shipyard mobilization base should: 1. Ensure that ships of the Naval fleet can be maintained in a high degree of material readiness and...capability to build combatants and cargo ship to wartime requirements and to support the goal of a merchant marine that is suitable in time of war or...guarantees, cargo reservation, the tax treatment of a ship operator’s construction reserve fund, and the Shipbuilding Trade Act of 1992. It will be shown

Plug Repairs of Marine Glass Fiber / Vinyl Ester Laminates Subjected to Uniaxial Tension

DTIC Science & Technology

2009-06-01

Material characteristics of glass fiber / vinyl ester composites used in naval surface ships 1.1.1.2 Construction of surface ship hulls with FRP...Piping - Ventilation ducts - Deck gratings 1.1.1.1 Material characteristics of glass fiber / vinyl ester composites used in naval surface ships The...that polysester-based composites do [15, 24]. Typical processing methods for vinyl ester composites are hand lay-up, Resin Transfer Molding (RTM

Land Based Anti-Ship Missiles: A Complementary Capability for Maintaining Access in an Anti-Access/Area Denial Environment

DTIC Science & Technology

2014-12-01

while underway. From S. Chandrashekar, N. Genesh, C.R. Raghunath , Rajaram Nagappa, N. Ramani and Lalitha Sundaresan, China’s Anti-Ship Ballistic...Chandrashekar, Genesh, Raghunath , Nagappa, Ramani and Sundaresan, China’s Anti- Ship Ballistic Missile Game Changer in the Pacific Ocean. International Strategic...Complete, ebscohost (accessed august 15, 2014). Chandrashekar, S., N. Genesh, C.R. Raghunath , Rajaram Nagappa, N. Ramani, and Lalitha Sundaresan

The Importance of Submarine Tenders to a Modern Naval War: Naval Combat Logistics and Seabasing

DTIC Science & Technology

2017-04-28

projected ship maintenance depots, and the time required for ships to travel back to US based facilities presents major operational consequences to...hour per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and...Department of the Navy. 14. ABSTRACT The potential for the US Navy’s adversaries to target its forward-projected ship maintenance depots, and the time

Future Fleet Project. What Can We Afford

DTIC Science & Technology

2016-12-21

like ships based on an LCS hull with improved armor and armament. These twenty ships would be preceded by eight transitional LCS THE JOHNS HOPKINS...large aviation-ship hull for Navy sea-control/power-projection air wings and for Marine Corps vertical-raid/assault-air wings, reconfigurable...or antisubmarine warfare (ASW) within a common hull type that can self-defend in peacetime but aggregate to fight offensively in wartime • Tactical

Optimizing the US Navy’s Combat Logistics Force

DTIC Science & Technology

2008-01-01

Optimizing the US Navy’s Combat Logistics Force Gerald G. Brown, W. Matthew Carlyle Operations Research Department, Naval Postgraduate School...Wiley InterScience (www.interscience.wiley.com). Abstract: We study how changes to the composition and employment of the US Navy combat logistic force...evaluate new CLF ship designs, advise what number of ships in a new ship class would be needed, test concepts for forward at-sea logistics bases in lieu

Digital Documentation of Ships in Cultural Heritage: a European Review

NASA Astrophysics Data System (ADS)

Colson, A.

2017-08-01

Ships of different shapes and times are lying in harbours, on land or in museums, all over the world. Our aim with this paper was to review work done on digital documentation of ships in Cultural Heritage based on different initiatives in Europe using Coordinate Measuring Machine (Newport Ship and Doel 1); Total Station Theodolite (Vasa and Mary-Rose) and Laser scanning (LaScanMar and Traditional boats of Ireland). Our results showed that some discrepancy exist between the projects, in terms of techniques and expertise at hand. Furthermore, few guidelines have been in practice but only for Archaeology and Ethnology. However, no standards are existing. Three focuses have emerged: documentation of single ship elements, monitoring of the long-term deformation processes and the documentation of collections of ships. We discussed the diversity of expert's background and the complexity of comparability between projects. In conclusion, guidelines are necessary to enable a common ground for all professions to work together, e.g. in Architecture. This path must be taken now for digital documentation of ships, if not information and knowledge will be lost on the way.

Experimental and theoretical study of magnetohydrodynamic ship models.

PubMed

Cébron, David; Viroulet, Sylvain; Vidal, Jérémie; Masson, Jean-Paul; Viroulet, Philippe

2017-01-01

Magnetohydrodynamic (MHD) ships represent a clear demonstration of the Lorentz force in fluids, which explains the number of students practicals or exercises described on the web. However, the related literature is rather specific and no complete comparison between theory and typical small scale experiments is currently available. This work provides, in a self-consistent framework, a detailed presentation of the relevant theoretical equations for small MHD ships and experimental measurements for future benchmarks. Theoretical results of the literature are adapted to these simple battery/magnets powered ships moving on salt water. Comparison between theory and experiments are performed to validate each theoretical step such as the Tafel and the Kohlrausch laws, or the predicted ship speed. A successful agreement is obtained without any adjustable parameter. Finally, based on these results, an optimal design is then deduced from the theory. Therefore this work provides a solid theoretical and experimental ground for small scale MHD ships, by presenting in detail several approximations and how they affect the boat efficiency. Moreover, the theory is general enough to be adapted to other contexts, such as large scale ships or industrial flow measurement techniques.

Underwater sound radiation patterns of contemporary merchant ships

NASA Astrophysics Data System (ADS)

Gassmann, M.; Wiggins, S. M.; Hildebrand, J. A.

2016-12-01

Merchant ships radiate underwater sound as an unintended by-product of their operation and as consequence contribute significantly to low-frequency, man-made noise in the ocean. Current measurement standards for the description of underwater sound from ships (ISO 17208-1:2016 and ANSI S12.64-2009) require nominal hydrophone depths of 15°, 30° and 45° at the starboard and portside of the test vessel.To opportunistically study the underwater sound of contemporary merchant ships that were tracked by the Automatic Identification System (AIS), an array of seven high-frequency acoustic recording packages (HARPs) with a sampling frequency of 200 kHz was deployed in the Santa Barbara Channel in the primary outgoing shipping lane for the port of Los Angeles and Long Beach. The vertical and horizontal aperture of the array allowed for starboard and portside measurements at all standard-required nominal hydrophone depths in addition to measurements taken at the keel aspect. Based on these measurements, frequency-dependent radiation patterns of contemporary merchant ships were estimated and used to evaluate current standards for computing ship source levels.

Ice and AIS: ship speed data and sea ice forecasts in the Baltic Sea

NASA Astrophysics Data System (ADS)

Löptien, U.; Axell, L.

2014-12-01

The Baltic Sea is a seasonally ice-covered marginal sea located in a densely populated area in northern Europe. Severe sea ice conditions have the potential to hinder the intense ship traffic considerably. Thus, sea ice fore- and nowcasts are regularly provided by the national weather services. Typically, the forecast comprises several ice properties that are distributed as prognostic variables, but their actual usefulness is difficult to measure, and the ship captains must determine their relative importance and relevance for optimal ship speed and safety ad hoc. The present study provides a more objective approach by comparing the ship speeds, obtained by the automatic identification system (AIS), with the respective forecasted ice conditions. We find that, despite an unavoidable random component, this information is useful to constrain and rate fore- and nowcasts. More precisely, 62-67% of ship speed variations can be explained by the forecasted ice properties when fitting a mixed-effect model. This statistical fit is based on a test region in the Bothnian Sea during the severe winter 2011 and employs 15 to 25 min averages of ship speed.

Ice and AIS: ship speed data and sea ice forecasts in the Baltic Sea

NASA Astrophysics Data System (ADS)

Löptien, U.; Axell, L.

2014-07-01

The Baltic Sea is a seasonally ice covered marginal sea located in a densely populated area in northern Europe. Severe sea ice conditions have the potential to hinder the intense ship traffic considerably. Thus, sea ice fore- and nowcasts are regularly provided by the national weather services. Typically, several ice properties are allocated, but their actual usefulness is difficult to measure and the ship captains must determine their relative importance and relevance for optimal ship speed and safety ad hoc. The present study provides a more objective approach by comparing the ship speeds, obtained by the Automatic Identification System (AIS), with the respective forecasted ice conditions. We find that, despite an unavoidable random component, this information is useful to constrain and rate fore- and nowcasts. More precisely, 62-67% of ship speed variations can be explained by the forecasted ice properties when fitting a mixed effect model. This statistical fit is based on a test region in the Bothnian Bay during the severe winter 2011 and employes 15 to 25 min averages of ship speed.

Sentinel-1 Contribution to Monitoring Maritime Activity in the Arctic

NASA Astrophysics Data System (ADS)

Santamaria, Carlos; Greidanus, Harm; Fournier, Melanie; Eriksen, Torkild; Vespe, Michele; Alvarez, Marlene; Arguedas, Virginia Fernandez; Delaney, Conor; Argentieri, Pietro

2016-08-01

This paper presents results on the use of Sentinel-1 combined with satellite AIS to monitor maritime activity in the Arctic. Such activities are expected to increase, even if not uniformly across the Arctic, as the ice cover in the region retreats due to changes in climate. The objectives of monitoring efforts in the region can vary from country to country, but are generally related to increasing awareness on non- cooperative, small and cruise ships, fisheries, safety at sea, and Search and Rescue. A ship monitoring study has been conducted, involving more than 2,000 Sentinel-1 images acquired during one year in the central Arctic, where the ship densities are high. The main challenges to SAR-based monitoring in this area are described, solutions for some of them are proposed, and analyses of the results are shown. With the high detection thresholds needed to prevent false alarms from sea ice, 16% of the ships detected overall in the Sentinel-1 images have not been correlated to AIS- transmitting ships, and 48% of the AIS-transmitting ships are not correlated to ships detected in the images.

Experimental and theoretical study of magnetohydrodynamic ship models

PubMed Central

Viroulet, Sylvain; Vidal, Jérémie; Masson, Jean-Paul; Viroulet, Philippe

2017-01-01

Magnetohydrodynamic (MHD) ships represent a clear demonstration of the Lorentz force in fluids, which explains the number of students practicals or exercises described on the web. However, the related literature is rather specific and no complete comparison between theory and typical small scale experiments is currently available. This work provides, in a self-consistent framework, a detailed presentation of the relevant theoretical equations for small MHD ships and experimental measurements for future benchmarks. Theoretical results of the literature are adapted to these simple battery/magnets powered ships moving on salt water. Comparison between theory and experiments are performed to validate each theoretical step such as the Tafel and the Kohlrausch laws, or the predicted ship speed. A successful agreement is obtained without any adjustable parameter. Finally, based on these results, an optimal design is then deduced from the theory. Therefore this work provides a solid theoretical and experimental ground for small scale MHD ships, by presenting in detail several approximations and how they affect the boat efficiency. Moreover, the theory is general enough to be adapted to other contexts, such as large scale ships or industrial flow measurement techniques. PMID:28665941

The right whale mandatory ship reporting system: a retrospective.

PubMed

Silber, Gregory K; Adams, Jeffrey D; Asaro, Michael J; Cole, Timothy V N; Moore, Katie S; Ward-Geiger, Leslie I; Zoodsma, Barbara J

2015-01-01

In 1998, the United States sought and received International Maritime Organization-endorsement of two Mandatory Ship Reporting (MSR) systems designed to improve mariner awareness about averting ship collisions with the endangered North Atlantic right whale (Eubalaena glacialis). Vessel collisions are a serious threat to the right whale and the program was among the first formal attempts to reduce this threat. Under the provisions of the MSR, all ships >300 gross tons are required to report their location, speed, and destination to a shore-based station when entering two key right whale habitats: one in waters off New England and one off coastal Georgia and Florida. In return, reporting ships receive an automatically-generated message, delivered directly to the ship's bridge, that provides information about right whale vulnerability to vessel collisions and actions mariners can take to avoid collisions. The MSR has been in operation continuously from July 1999 to the present. Archived incoming reports provided a 15-plus year history of ship operations in these two locations. We analyzed a total of 26,772 incoming MSR messages logged between July 1999 and December 2013. Most ships that were required to report did so, and compliance rates were generally constant throughout the study period. Self-reported vessel speeds when entering the systems indicated that most ships travelled between 10 and 16 (range = 5-20 +) knots. Ship speeds generally decreased in 2009 to 2013 following implementation of vessel speed restrictions. The number of reports into the southern system remained relatively constant following a steady increase through 2007, but numbers in the northern system decreased annually beginning in 2008. If reporting is indicative of long-term patterns in shipping operations, it reflects noteworthy changes in marine transportation. Observed declines in ship traffic are likely attributable to the 2008-2009 economic recession, the containerized shipping industry making increased use of larger ships that made fewer trips, and diminished oil/gas US imports as previously inaccessible domestic deposits were exploited. Recent declines in shipping activity likely resulted in lowered collision risks for right whales and reduced their exposure to underwater noise from ships.

User’s Manual for Strategic Satellite System Terminal Segment Life Cycle Cost Model. Volume 2

DTIC Science & Technology

1981-03-01

BASE TO/38X,15HDEPOT IN MONTHS,35X,F15.3/28X,55H + OSTC - ORDER AND SHIPPING TIME FROM A SATELLITE BASE/38X,26HT0 I +TS CIMP BASE IN MONTHS,24X,F15.3...COST OF PACKING AND SHIP +PING FROM A SATELLITE/38X,47HBASE TO ITS CIMP BASE IN $ PER NET WE +IGHT POUND,3X,F15.3/28X,54HCPPDC1) -COST OF PACKING AND

Stochastic inversion of ocean color data using the cross-entropy method.

PubMed

Salama, Mhd Suhyb; Shen, Fang

2010-01-18

Improving the inversion of ocean color data is an ever continuing effort to increase the accuracy of derived inherent optical properties. In this paper we present a stochastic inversion algorithm to derive inherent optical properties from ocean color, ship and space borne data. The inversion algorithm is based on the cross-entropy method where sets of inherent optical properties are generated and converged to the optimal set using iterative process. The algorithm is validated against four data sets: simulated, noisy simulated in-situ measured and satellite match-up data sets. Statistical analysis of validation results is based on model-II regression using five goodness-of-fit indicators; only R2 and root mean square of error (RMSE) are mentioned hereafter. Accurate values of total absorption coefficient are derived with R2 > 0.91 and RMSE, of log transformed data, less than 0.55. Reliable values of the total backscattering coefficient are also obtained with R2 > 0.7 (after removing outliers) and RMSE < 0.37. The developed algorithm has the ability to derive reliable results from noisy data with R2 above 0.96 for the total absorption and above 0.84 for the backscattering coefficients. The algorithm is self contained and easy to implement and modify to derive the variability of chlorophyll-a absorption that may correspond to different phytoplankton species. It gives consistently accurate results and is therefore worth considering for ocean color global products.

Optimization of 200 MWth and 250 MWt Ship Based Small Long Life NPP

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fitriyani, Dian; Su'ud, Zaki

2010-06-22

Design optimization of ship-based 200 MWth and 250 MWt nuclear power reactors have been performed. The neutronic and thermo-hydraulic programs of the three-dimensional X-Y-Z geometry have been developed for the analysis of ship-based nuclear power plant. Quasi-static approach is adopted to treat seawater effect. The reactor are loop type lead bismuth cooled fast reactor with nitride fuel and with relatively large coolant pipe above reactor core, the heat from primary coolant system is directly transferred to watersteam loop through steam generators. Square core type are selected and optimized. As the optimization result, the core outlet temperature distribution is changing withmore » the elevation angle of the reactor system and the characteristics are discussed.« less

Level-Set Simulation of Viscous Free Surface Flow Around a Commercial Hull Form

DTIC Science & Technology

2005-04-15

Abstract The viscous free surface flow around a 3600 TEU KRISO Container Ship is computed using the finite volume based multi-block RANS code, WAVIS...developed at KRISO . The free surface is captured with the Level-set method and the realizable k-ε model is employed for turbulence closure. The...computations are done for a 3600 TEU container ship of Korea Research Institute of Ships & Ocean Engineering, KORDI (hereafter, KRISO ) selected as

Assessing Motion Induced Interruptions Using a Motion Platform

DTIC Science & Technology

2013-09-01

same way that cars have shock absorbers to decrease jolt from potholes and bumps in the road, ships may have the potential to be designed to better...Integration (HSI) seeks to assure human performance to reduce operating costs. This thesis seeks to develop a model for ship design in relation to Motion...Induced Interruptions (MII). The model is based on the premise that MIIs affect specific domains of HSI in an adverse way. Future ship design

Contribution of ship emissions to the concentration and deposition of air pollutants in Europe

NASA Astrophysics Data System (ADS)

Aksoyoglu, Sebnem; Baltensperger, Urs; Prévôt, André S. H.

2016-02-01

Emissions from the marine transport sector are one of the least-regulated anthropogenic emission sources and contribute significantly to air pollution. Although strict limits were introduced recently for the maximum sulfur content in marine fuels in the SECAs (sulfur emission control areas) and in EU ports, sulfur emissions outside the SECAs and emissions of other components in all European maritime areas have continued to increase in the last two decades. We have used the air quality model CAMx (Comprehensive Air Quality Model with Extensions) with and without ship emissions for the year 2006 to determine the effects of international shipping on the annual as well as seasonal concentrations of ozone, primary and secondary components of PM2.5, and the dry and wet deposition of nitrogen and sulfur compounds in Europe. The largest changes in pollutant concentrations due to ship emissions were predicted for summer. Concentrations of particulate sulfate increased due to ship emissions in the Mediterranean (up to 60 %), the English Channel and the North Sea (30-35 %), while increases in particulate nitrate levels were found especially in the north, around the Benelux area (20 %), where there were high NH3 land-based emissions. Our model results showed that not only are the atmospheric concentrations of pollutants affected by ship emissions, but also depositions of nitrogen and sulfur compounds increase significantly along the shipping routes. NOx emissions from the ships, especially in the English Channel and the North Sea, cause a decrease in the dry deposition of reduced nitrogen at source regions by moving it from the gas phase to the particle phase which then contributes to an increase in the wet deposition at coastal areas with higher precipitation. In the western Mediterranean region, on the other hand, model results show an increase in the deposition of oxidized nitrogen (mostly HNO3) due to the ship traffic. Dry deposition of SO2 seems to be significant along the shipping routes, whereas sulfate wet deposition occurs mainly along the Scandinavian and Adriatic coasts. The results presented in this paper suggest that evolution of NOx emissions from ships and land-based NH3 emissions will play a significant role in future European air quality.

Evaluation of Fast Technology Analysis (FTA) Cards as an improved method for specimen collection and shipment targeting viruses associated with Bovine Respiratory Disease Complex.

PubMed

Liang, Xiao; Chigerwe, Munashe; Hietala, Sharon K; Crossley, Beate M

2014-06-01

In order to improve the analytic quality of respiratory specimens collected from cattle for nucleic acid-based diagnosis, a study was undertaken to verify realtime PCR efficiency of specimens collected and stabilized on FTA Cards™, filter paper which is treated chemically. Nucleic acids collected using FTA Cards without the need for a cold-chain or special liquid media handling provided realtime PCR results consistent (96.8% agreement, kappa 0.923 [95% CI=0.89-0.96]) with the same specimens collected using traditional viral transport media and shipped on ice using the U.S. Department of Transportation mandated liquid handling requirements. Nucleic acid stabilization on FTA Cards was evaluated over a temperature range (-27 °C to +46 °C) for up to 14 days to mimic environmental conditions for diagnostic sample handling between collection and processing in a routine veterinary laboratory. No significant difference (P≥0.05) was observed in realtime PCR cycle threshold values over the temperature range and time storage conditions for Bovine Viral Diarrhea virus, Bovine Respiratory Syncytial virus, Bovine Coronavirus, and Bovine Herpesvirus I. The four viruses evaluated in the study are associated with Bovine Respiratory Disease Complex where improvements in ease and reliability of specimen collection and shipping would enhance the diagnostic quality of specimens collected in the field, and ultimately improve diagnostic efficiency. Copyright © 2014 Elsevier B.V. All rights reserved.

The right whale mandatory ship reporting system: a retrospective

PubMed Central

Adams, Jeffrey D.; Asaro, Michael J.; Cole, Timothy V.N.; Moore, Katie S.; Ward-Geiger, Leslie I.; Zoodsma, Barbara J.

2015-01-01

In 1998, the United States sought and received International Maritime Organization-endorsement of two Mandatory Ship Reporting (MSR) systems designed to improve mariner awareness about averting ship collisions with the endangered North Atlantic right whale (Eubalaena glacialis). Vessel collisions are a serious threat to the right whale and the program was among the first formal attempts to reduce this threat. Under the provisions of the MSR, all ships >300 gross tons are required to report their location, speed, and destination to a shore-based station when entering two key right whale habitats: one in waters off New England and one off coastal Georgia and Florida. In return, reporting ships receive an automatically-generated message, delivered directly to the ship’s bridge, that provides information about right whale vulnerability to vessel collisions and actions mariners can take to avoid collisions. The MSR has been in operation continuously from July 1999 to the present. Archived incoming reports provided a 15-plus year history of ship operations in these two locations. We analyzed a total of 26,772 incoming MSR messages logged between July 1999 and December 2013. Most ships that were required to report did so, and compliance rates were generally constant throughout the study period. Self-reported vessel speeds when entering the systems indicated that most ships travelled between 10 and 16 (range = 5–20 +) knots. Ship speeds generally decreased in 2009 to 2013 following implementation of vessel speed restrictions. The number of reports into the southern system remained relatively constant following a steady increase through 2007, but numbers in the northern system decreased annually beginning in 2008. If reporting is indicative of long-term patterns in shipping operations, it reflects noteworthy changes in marine transportation. Observed declines in ship traffic are likely attributable to the 2008–2009 economic recession, the containerized shipping industry making increased use of larger ships that made fewer trips, and diminished oil/gas US imports as previously inaccessible domestic deposits were exploited. Recent declines in shipping activity likely resulted in lowered collision risks for right whales and reduced their exposure to underwater noise from ships. PMID:25861555

Using the time shift in single pushbroom datatakes to detect ships and their heading

NASA Astrophysics Data System (ADS)

Willburger, Katharina A. M.; Schwenk, Kurt

2017-10-01

The detection of ships from remote sensing data has become an essential task for maritime security. The variety of application scenarios includes piracy, illegal fishery, ocean dumping and ships carrying refugees. While techniques using data from SAR sensors for ship detection are widely common, there is only few literature discussing algorithms based on imagery of optical camera systems. A ship detection algorithm for optical pushbroom data has been developed. It takes advantage of the special detector assembly of most of those scanners, which allows apart from the detection of a ship also the calculation of its heading out of a single acquisition. The proposed algorithm for the detection of moving ships was developed with RapidEye imagery. It algorithm consists mainly of three steps: the creation of a land-watermask, the object extraction and the deeper examination of each single object. The latter step is built up by several spectral and geometric filters, making heavy use of the inter-channel displacement typical for pushbroom sensors with multiple CCD lines, finally yielding a set of ships and their direction of movement. The working principle of time-shifted pushbroom sensors and the developed algorithm is explained in detail. Furthermore, we present our first results and give an outlook to future improvements.

A simple analytical infiltration model for short-duration rainfall

NASA Astrophysics Data System (ADS)

Wang, Kaiwen; Yang, Xiaohua; Liu, Xiaomang; Liu, Changming

2017-12-01

Many infiltration models have been proposed to simulate infiltration process. Different initial soil conditions and non-uniform initial water content can lead to infiltration simulation errors, especially for short-duration rainfall (SHR). Few infiltration models are specifically derived to eliminate the errors caused by the complex initial soil conditions. We present a simple analytical infiltration model for SHR infiltration simulation, i.e., Short-duration Infiltration Process model (SHIP model). The infiltration simulated by 5 models (i.e., SHIP (high) model, SHIP (middle) model, SHIP (low) model, Philip model and Parlange model) were compared based on numerical experiments and soil column experiments. In numerical experiments, SHIP (middle) and Parlange models had robust solutions for SHR infiltration simulation of 12 typical soils under different initial soil conditions. The absolute values of percent bias were less than 12% and the values of Nash and Sutcliffe efficiency were greater than 0.83. Additionally, in soil column experiments, infiltration rate fluctuated in a range because of non-uniform initial water content. SHIP (high) and SHIP (low) models can simulate an infiltration range, which successfully covered the fluctuation range of the observed infiltration rate. According to the robustness of solutions and the coverage of fluctuation range of infiltration rate, SHIP model can be integrated into hydrologic models to simulate SHR infiltration process and benefit the flood forecast.

Viking-Age Sails: Form and Proportion

NASA Astrophysics Data System (ADS)

Bischoff, Vibeke

2017-04-01

Archaeological ship-finds have shed much light on the design and construction of vessels from the Viking Age. However, the exact proportions of their sails remain unknown due to the lack of fully preserved sails, or other definite indicators of their proportions. Key Viking-Age ship-finds from Scandinavia—the Oseberg Ship, the Gokstad Ship and Skuldelev 3—have all revealed traces of rigging. In all three finds, the keelson—with the mast position—is preserved, together with fastenings for the sheets and the tack, indicating the breadth of the sail. The sail area can then be estimated based on practical experience of how large a sail the specific ship can carry, in conjunction with hull form and displacement. This article presents reconstructions of the form and dimensions of rigging and sail based on the archaeological finds, evidence from iconographic and written sources, and ethnographic parallels with traditional Nordic boats. When these sources are analysed, not only do the similarities become apparent, but so too does the relative disparity between the archaeological record and the other sources. Preferential selection in terms of which source is given the greatest merit is therefore required, as it is not possible to afford them all equal value.

Ballast water treatment systems: design, regulations, and selection under the choice varying priorities.

PubMed

Satir, Tanzer

2014-09-01

This paper investigates the role of ballast water treatment systems (BWTSs) and proposes a selection procedure for conventional merchant ships based on the financial, legal, and operational circumstances. Through the metallurgical revolution of the nineteenth century, commercial ships are converted to steel hull from wooden structures. By this innovative shift, use of ballast water became an essential part of ships for improving propulsion and stability while reducing stress on hull (instead of rocks). However, the content of ballast water is emerged since it relocates marine species from an ecological composition (usually cargo discharging port) to another one (loading port). Uncontrolled relocation of marine species may cause severe damage to existing ecological basis on ballast discharging area. BWTSs are developed for ships to eliminate marine species (i.e., aquatic invasive species) content by using a filtering device. It ensures an eco-friendly ballasting and de-ballasting process. The selection of proper BWTS is another debate since the BWTSs are designed with cost-quality and cost (eco)-performance variations. The proposed approach denoted that both tonnage and the age of ship are indicative factors on selection. The cost of installation varies based on installation space and active vs. project vessel cases.

Combustion of hydrogen injected into a supersonic airstream (the SHIP computer program)

NASA Technical Reports Server (NTRS)

Markatos, N. C.; Spalding, D. B.; Tatchell, D. G.

1977-01-01

The mathematical and physical basis of the SHIP computer program which embodies a finite-difference, implicit numerical procedure for the computation of hydrogen injected into a supersonic airstream at an angle ranging from normal to parallel to the airstream main flow direction is described. The physical hypotheses built into the program include: a two-equation turbulence model, and a chemical equilibrium model for the hydrogen-oxygen reaction. Typical results for equilibrium combustion are presented and exhibit qualitatively plausible behavior. The computer time required for a given case is approximately 1 minute on a CDC 7600 machine. A discussion of the assumption of parabolic flow in the injection region is given which suggests that improvement in calculation in this region could be obtained by use of the partially parabolic procedure of Pratap and Spalding. It is concluded that the technique described herein provides the basis for an efficient and reliable means for predicting the effects of hydrogen injection into supersonic airstreams and of its subsequent combustion.

Future development of the PLATO Observatory for Antarctic science

NASA Astrophysics Data System (ADS)

Ashley, Michael C. B.; Bonner, Colin S.; Everett, Jon R.; Lawrence, Jon S.; Luong-Van, Daniel; McDaid, Scott; McLaren, Campbell; Storey, John W. V.

2010-07-01

PLATO is a self-contained robotic observatory built into two 10-foot shipping containers. It has been successfully deployed at Dome A on the Antarctic plateau since January 2008, and has accumulated over 730 days of uptime at the time of writing. PLATO provides 0.5{1kW of continuous electrical power for a year from diesel engines running on Jet-A1, supplemented during the summertime with solar panels. One of the 10-foot shipping containers houses the power system and fuel, the other provides a warm environment for instruments. Two Iridium satellite modems allow 45 MB/day of data to be transferred across the internet. Future enhancements to PLATO, currently in development, include a more modular design, using lithium iron-phosphate batteries, higher power output, and a light-weight low-power version for eld deployment from a Twin Otter aircraft. Technologies used in PLATO include a CAN (Controller Area Network) bus, high-reliability PC/104 com- puters, ultracapacitors for starting the engines, and fault-tolerant redundant design.

EQ-10 electrodeless Z-pinch EUV source for metrology applications

NASA Astrophysics Data System (ADS)

Gustafson, Deborah; Horne, Stephen F.; Partlow, Matthew J.; Besen, Matthew M.; Smith, Donald K.; Blackborow, Paul A.

2011-11-01

With EUV Lithography systems shipping, the requirements for highly reliable EUV sources for mask inspection and resist outgassing are becoming better defined, and more urgent. The sources needed for metrology applications are very different than that needed for lithography; brightness (not power) is the key requirement. Suppliers for HVM EUV sources have all resources working on high power and have not entered the smaller market for metrology. Energetiq Technology has been shipping the EQ-10 Electrodeless Z-pinchTM light source since 19951. The source is currently being used for metrology, mask inspection, and resist development2-4. These applications require especially stable performance in both output power and plasma size and position. Over the last 6 years Energetiq has made many source modifications which have included better thermal management to increase the brightness and power of the source. We now have introduced a new source that will meet requirements of some of the mask metrology first generation tools; this source will be reviewed.

Panel cutting method: new approach to generate panels on a hull in Rankine source potential approximation

NASA Astrophysics Data System (ADS)

Choi, Hee-Jong; Chun, Ho-Hwan; Park, Il-Ryong; Kim, Jin

2011-12-01

In the present study, a new hull panel generation algorithm, namely panel cutting method, was developed to predict flow phenomena around a ship using the Rankine source potential based panel method, where the iterative method was used to satisfy the nonlinear free surface condition and the trim and sinkage of the ship was taken into account. Numerical computations were performed to investigate the validity of the proposed hull panel generation algorithm for Series 60 (CB=0.60) hull and KRISO container ship (KCS), a container ship designed by Maritime and Ocean Engineering Research Institute (MOERI). The computational results were validated by comparing with the existing experimental data.

The choice of speed and clearance for RAS on 3D method

NASA Astrophysics Data System (ADS)

Wang, Jian-Fang; Li, Ji-De; Cai, Xin-Gong

2003-12-01

In this paper, a 3D source distribution technique is used to calculate the coupled motions between two ships which advance in the wave with the same speed. The numerical results of coupled motions for a frigate and a supply ship have a good agreement with the experimental results. Based on the 3D coupled motions of two ships, a spectral analysis is employed to clearly observe the effect of speed, clearance and wave heading on the significant relative motion amplitude (SRMA) of two ships. The method presented in this paper will be helpful to select suitable clearance, speed and wave heading for underway replenishment at sea(RAS).

Ship speeds and sea ice forecasts - how are they related?

NASA Astrophysics Data System (ADS)

Loeptien, Ulrike; Axell, Lars

2014-05-01

The Baltic Sea is a shallow marginal sea, located in northern Europe. A seasonally occurring sea ice cover has the potential to hinder the intense ship traffic substantially. There are thus considerable efforts to fore- and nowcast ice conditions. Here we take a somewhat opposite approach and relate ship speeds, as observed via the Automatic Identification System (AIS) network, back to the prevailing sea ice conditions. We show that these information are useful to constrain fore- and nowcasts. More specifically we find, by fitting a statistical model (mixed effect model) for a test region in the Bothnian Bay, that the forecasted ice properties can explain 60-65% of the ship speed variations (based on 25 minute averages).

Wind and Current Forces Acting on Canadian Forces Ships During Tug Operations

DTIC Science & Technology

2002-11-01

McTaggart and Sav- age [1] describe model tests conducted on a generic frigate model to determine wind forces influencing ship capsize. Van Manen and van ...Fn will be 0.06. Based on data presented by van Manen and van Oossanen [2], the fric- tional resistance coefficient will be approximately 0.002 and...Conference on Stability of Ships and Ocean Vehicles (Melbourne, Florida, 1994). 2. J.D. van Manen and P. van Oossanen, Principles of Naval Architecture, Volume

Instruments and Methods for Measuring the Flow of Water Around Ships and Ship Models

DTIC Science & Technology

1948-03-01

velocity of flow, the direction of flow, and the speed of a ship are based on the pitot tube design- ed by Henri Pitot , a French physicist and engineer of...INTRODUCTION . .’ 1 DEVELOPMENT OP EARLY INSTRUMENTS . 2 PITOT -STATIC TUBE 2 SPEED LOOS k INSTRUMENT.- USED BY THE TAYLOR MODEL BASIN...5 CYLINDRICAL PITOT TUBE 5 SPHERICAL PITOT TUBE 10 ROTATING WAKE METER 1? BOW LOO 19 INSTRUMENTS USED BY OTHER MODEL BASINS 21

A Novel Ship-Tracking Method for GF-4 Satellite Sequential Images.

PubMed

Yao, Libo; Liu, Yong; He, You

2018-06-22

The geostationary remote sensing satellite has the capability of wide scanning, persistent observation and operational response, and has tremendous potential for maritime target surveillance. The GF-4 satellite is the first geostationary orbit (GEO) optical remote sensing satellite with medium resolution in China. In this paper, a novel ship-tracking method in GF-4 satellite sequential imagery is proposed. The algorithm has three stages. First, a local visual saliency map based on local peak signal-to-noise ratio (PSNR) is used to detect ships in a single frame of GF-4 satellite sequential images. Second, the accuracy positioning of each potential target is realized by a dynamic correction using the rational polynomial coefficients (RPCs) and automatic identification system (AIS) data of ships. Finally, an improved multiple hypotheses tracking (MHT) algorithm with amplitude information is used to track ships by further removing the false targets, and to estimate ships’ motion parameters. The algorithm has been tested using GF-4 sequential images and AIS data. The results of the experiment demonstrate that the algorithm achieves good tracking performance in GF-4 satellite sequential images and estimates the motion information of ships accurately.

An Adaptive Ship Detection Algorithm for Hrws SAR Images Under Complex Background: Application to SENTINEL1A Data

NASA Astrophysics Data System (ADS)

He, G.; Xia, Z.; Chen, H.; Li, K.; Zhao, Z.; Guo, Y.; Feng, P.

2018-04-01

Real-time ship detection using synthetic aperture radar (SAR) plays a vital role in disaster emergency and marine security. Especially the high resolution and wide swath (HRWS) SAR images, provides the advantages of high resolution and wide swath synchronously, significantly promotes the wide area ocean surveillance performance. In this study, a novel method is developed for ship target detection by using the HRWS SAR images. Firstly, an adaptive sliding window is developed to propose the suspected ship target areas, based upon the analysis of SAR backscattering intensity images. Then, backscattering intensity and texture features extracted from the training samples of manually selected ship and non-ship slice images, are used to train a support vector machine (SVM) to classify the proposed ship slice images. The approach is verified by using the Sentinl1A data working in interferometric wide swath mode. The results demonstrate the improvement performance of the proposed method over the constant false alarm rate (CFAR) method, where the classification accuracy improved from 88.5 % to 96.4 % and the false alarm rate mitigated from 11.5 % to 3.6 % compared with CFAR respectively.

Estimating ship emissions based on AIS data for port of Tianjin, China

NASA Astrophysics Data System (ADS)

Chen, Dongsheng; Zhao, Yuehua; Nelson, Peter; Li, Yue; Wang, Xiaotong; Zhou, Ying; Lang, Jianlei; Guo, Xiurui

2016-11-01

A detailed exhaust emission inventory of ships by using Automatic Identification System (AIS) data was developed for Tianjin Port, one of the top 10 world container ports and the largest port in North China. It was found that in 2014, ship emissions are 2.93 × 104, 4.13 × 104, 4.03 × 103, 3.72 × 103, 1.72 × 103 and 3.57 × 103 tonnes of SO2, NOx, PM10, PM2.5, NMVOC and CO respectively, which are equivalent to 11.07%, 9.40%, 2.43%, 3.10%, 0.43% and 0.16% respectively of the non-ship anthropogenic totals in Tianjin. The total CO2 emissions is approximately 1.97 × 106 tonnes. The container ships and dry bulk cargo ships contributed about 70% of the total ship emissions of NOx, SO2 and PM10. Pollutants were mainly emitted during cruise and hotelling modes, and the highest intensities of emissions located in the vicinity of fairways, berth and anchorage areas in Tianjin Port. Distinctive difference between the lowest (February) and the highest (September) monthly emissions is due to the adjustment of freight volume during the Chinese New Year and the months before and after it.

Modelling the emissions from ships in ports and their impact on air quality in the metropolitan area of Hamburg

NASA Astrophysics Data System (ADS)

Ramacher, Martin; Karl, Matthias; Aulinger, Armin; Bieser, Johannes; Matthias, Volker; Quante, Markus

2016-04-01

Exhaust emissions from shipping contribute significantly to the anthropogenic burden of air pollutants such as nitrogen oxides (NOX) and particulate matter (PM). Ships emit not only when sailing on open sea, but also when approaching harbors, during port manoeuvers and at berth to produce electricity and heat for the ship's operations. This affects the population of harbor cities because long-term exposure to PM and NOX has significant effects on human health. The European Union has therefore has set air quality standards for air pollutants. Many port cities have problems meeting these standards. The port of Hamburg with around 10.000 ship calls per year is Germany's largest seaport and Europe's second largest container port. Air quality standard reporting in Hamburg has revealed problems in meeting limits for NO2 and PM10. The amount and contribution of port related ship emissions (38% for NOx and 17% for PM10) to the overall emissions in the metropolitan area in 2005 [BSU Hamburg (2012): Luftreinhalteplan für Hamburg. 1. Fortschreibung 2012] has been modelled with a bottom up approach by using statistical data of ship activities in the harbor, technical vessel information and specific emission algorithms [GAUSS (2008): Quantifizierung von gasförmigen Emissionen durch Maschinenanlagen der Seeschiffart an der deutschen Küste]. However, knowledge about the spatial distribution of the harbor ship emissions over the city area is crucial when it comes to air quality standards and policy decisions to protect human health. Hence, this model study examines the spatial distribution of harbor ship emissions (NOX, PM10) and their deposition in the Hamburg metropolitan area. The transport and chemical transformation of atmospheric pollutants is calculated with the well-established chemistry transport model TAPM (The Air Pollution Model). TAPM is a three-dimensional coupled prognostic meteorological and air pollution model with a condensed chemistry scheme including photochemistry. The model was applied to the Hamburg metropolitan area with a setup of 30 x 30 grid cells of 1 km² each and 30 vertical grid levels from 10 to 8,000 m, for a time period of one year. Emission inventories for traffic, industry, households and ships in 2013 were generated. To investigate the dispersion of ship emissions to air pollution two different model runs for 2013 were performed; one model run including land-based emissions and the ship emissions and a model run just including the land-based emissions. The modelling results were evaluated with air quality data from the monitoring station network of Hamburg (luft.hamburg.de). The results are presented in form of spatial distribution maps for the Hamburg metropolitan area highlighting the pollutants (PM and NOX) originating from harbor residential ships.

The Sam-Sam interaction between Ship2 and the EphA2 receptor: design and analysis of peptide inhibitors.

PubMed

Mercurio, Flavia Anna; Di Natale, Concetta; Pirone, Luciano; Iannitti, Roberta; Marasco, Daniela; Pedone, Emilia Maria; Palumbo, Rosanna; Leone, Marilisa

2017-12-12

The lipid phosphatase Ship2 represents a drug discovery target for the treatment of different diseases, including cancer. Its C-terminal sterile alpha motif domain (Ship2-Sam) associates with the Sam domain from the EphA2 receptor (EphA2-Sam). This interaction is expected to mainly induce pro-oncogenic effects in cells therefore, inhibition of the Ship2-Sam/EphA2-Sam complex may represent an innovative route to discover anti-cancer therapeutics. In the present work, we designed and analyzed several peptide sequences encompassing the interaction interface of EphA2-Sam for Ship2-Sam. Peptide conformational analyses and interaction assays with Ship2-Sam conducted through diverse techniques (CD, NMR, SPR and MST), identified a positively charged penta-amino acid native motif in EphA2-Sam, that once repeated three times in tandem, binds Ship2-Sam. NMR experiments show that the peptide targets the negatively charged binding site of Ship2-Sam for EphA2-Sam. Preliminary in vitro cell-based assays indicate that -at 50 µM concentration- it induces necrosis of PC-3 prostate cancer cells with more cytotoxic effect on cancer cells than on normal dermal fibroblasts. This work represents a pioneering study that opens further opportunities for the development of inhibitors of the Ship2-Sam/EphA2-Sam complex for therapeutic applications.

ARM Navigation Best Estimate 10 Hz (NAVBE) and 1-min (NAVBE1M) Value Added Products (VAP) for Ship Deployments

DOE Data Explorer

Toto, Tami; Jensen, Michael; Bartholomew, Mary Jane

2012-09-22

The Navigation Best Estimate (NAVBE) VAP was developed in response to the 2012-2013 Marine ARM GPCI Investigation of Clouds (MAGIC) deployment, the first ship-based deployment of the second ARM Mobile Facility (AMF2). It has since been applied to the 2015 ARM Cloud Aerosol Precipitation EXperiment (ACAPEX) deployment. A number of different instruments on the ships collected Global Positioning System (GPS) and Inertial Navigation System (INS) measurements during the MAGIC campaign. The motivation of the NAVBE VAP is to consolidate many different sources of this information in a single, continuous datastream to be used when information is required about ship location and orientation and to provide a more complete estimate than would be available from any one instrument. The result is 10 Hz and 1-min data streams reporting ship position and attitude

Diatom community structure on in-service cruise ship hulls.

PubMed

Hunsucker, Kelli Zargiel; Koka, Abhishek; Lund, Geir; Swain, Geoffrey

2014-10-01

Diatoms are an important component of marine biofilms found on ship hulls. However, there are only a few published studies that describe the presence and abundance of diatoms on ships, and none that relate to modern ship hull coatings. This study investigated the diatom community structure on two in-service cruise ships with the same cruise cycles, one coated with an antifouling (AF) system (copper self-polishing copolymer) and the other coated with a silicone fouling-release (FR) system. Biofilm samples were collected during dry docking from representative areas of the ship and these provided information on the horizontal and vertical zonation of the hull, and intact and damaged coating and niche areas. Diatoms from the genera Achnanthes, Amphora and Navicula were the most common, regardless of horizontal ship zonation and coating type. Other genera were abundant, but their presence was more dependent on the ship zonation and coating type. Samples collected from damaged areas of the hull coating had a similar community composition to undamaged areas, but with higher diatom abundance. Diatom fouling on the niche areas differed from that of the surrounding ship hull and paralleled previous studies that investigated differences in diatom community structure on static and dynamically exposed coatings; niche areas were similar to static immersion and the hull to dynamic immersion. Additionally, diatom richness was greater on the ship with the FR coating, including the identification of several new genera to the biofouling literature, viz. Lampriscus and Thalassiophysa. These results are the first to describe diatom community composition on in-service ship hulls coated with a FR system. This class of coatings appears to have a larger diatom community compared to copper-based AF systems, with new diatom genera that have the ability to stick to ship hulls and withstand hydrodynamic forces, thus creating the potential for new problematic species in the biofilm.

A proposed new generation of intact stability criteria for assessment of ship stability in longitudinal waves

NASA Astrophysics Data System (ADS)

Andrei, C.

2017-08-01

Intact ship stability assessment to prevent stability failure in heavy weather conditions is of paramount importance on board vessel. The possibility of assessment the causes that can lead to loss of ship’s stability as well as the assessment of intact stability in heavy seas is a important problem and has attracted a huge interest of the national and international regulatory authorities. Despite the regulations in force, referring to intact ship stability, many ships continued to lose the stability and or capsize due to failure modes that presently are not covered by such regulations. Based on this aspect has been identified the necessity of modelling an updated criteria for assessment of ship’s stability taking into consideration actual possible situations for loss of stability in heavy seas as a measure of increasing she safety of ships. In this respect, the goal of this paper is to illustrate a possible criteria for assessment ship’s stability in heavy seas through a method of determination the possible problems in a form of dynamic stability criteria. A new intact stability criteria is proposed and developed based on separate levels for assessment of vulnerability and susceptibility of ships in situations of parametric rolling and pure loss of stability encountered in extreme sea conditions. Mathematical models correlated with ship’s construction particulars and weather conditions were developed for every separate level in order to assess the ship’s stability. The objective of the proposed criteria is to bring to officers on board ships the possibility of assessment the ship’s intact stability, as a measure of prevention and improvement of safety during the voyage.

From Ship-To-Shore In Real Time: Data Transmission, Distribution, Management, Processing, And Archiving Using Telepresence Technologies And The Inner Space Center

NASA Astrophysics Data System (ADS)

Coleman, D. F.

2012-12-01

Most research vessels are equipped with satellite Internet services with bandwidths capable of being upgraded to support telepresence technologies and live shore-based participation. This capability can be used for real-time data transmission to shore, where it can be distributed, managed, processed, and archived. The University of Rhode Island Inner Space Center utilizes telepresence technologies and a growing network of command centers on Internet2 to participate live with a variety of research vessels and their ocean observing and sampling systems. High-bandwidth video streaming, voice-over-IP telecommunications, and real-time data feeds and file transfers enable users on shore to take part in the oceanographic expeditions as if they were present on the ship, working in the lab. Telepresence-enabled systematic ocean exploration and similar programs represent a significant and growing paradigm shift that can change the future of seagoing ocean observations using research vessels. The required platform is the ship itself, and users of the technology rely on the ship-based technical teams, but remote and distributed shore-based science users, students, educators, and the general public can now take part by being aboard virtually.

A Horizontal Tilt Correction Method for Ship License Numbers Recognition

NASA Astrophysics Data System (ADS)

Liu, Baolong; Zhang, Sanyuan; Hong, Zhenjie; Ye, Xiuzi

2018-02-01

An automatic ship license numbers (SLNs) recognition system plays a significant role in intelligent waterway transportation systems since it can be used to identify ships by recognizing the characters in SLNs. Tilt occurs frequently in many SLNs because the monitors and the ships usually have great vertical or horizontal angles, which decreases the accuracy and robustness of a SLNs recognition system significantly. In this paper, we present a horizontal tilt correction method for SLNs. For an input tilt SLN image, the proposed method accomplishes the correction task through three main steps. First, a MSER-based characters’ center-points computation algorithm is designed to compute the accurate center-points of the characters contained in the input SLN image. Second, a L 1- L 2 distance-based straight line is fitted to the computed center-points using M-estimator algorithm. The tilt angle is estimated at this stage. Finally, based on the computed tilt angle, an affine transformation rotation is conducted to rotate and to correct the input SLN horizontally. At last, the proposed method is tested on 200 tilt SLN images, the proposed method is proved to be effective with a tilt correction rate of 80.5%.

A new bioassay for the inspection and identification of TBT-containing antifouling paint.

PubMed

Gueuné, Hervé; Thouand, Gérald; Durand, Marie-José

2009-11-01

Since the 1960s tributyl (TBT)-based antifouling paints are widely applied to protect ship's hulls from biofouling. Due to its high toxicity to aquatic ecosystem most of the countries (28 nations in 2008) signed the AFS convention to control the use of harmful antifouling systems on ships. Nevertheless there is currently no simple method to control the presence of organotin in paint. In this study, we propose a bioassay based on the use of a recombinant bioluminescent bacteria to detect directly in paint the presence of TBT. We also propose a simple device as an inspection system to control the absence of organotin in the ship's hull paint. The presence of organotin could be revealed in less than three hours.

Technique for ship/wake detection

DOEpatents

Roskovensky, John K [Albuquerque, NM

2012-05-01

An automated ship detection technique includes accessing data associated with an image of a portion of Earth. The data includes reflectance values. A first portion of pixels within the image are masked with a cloud and land mask based on spectral flatness of the reflectance values associated with the pixels. A given pixel selected from the first portion of pixels is unmasked when a threshold number of localized pixels surrounding the given pixel are not masked by the cloud and land mask. A spatial variability image is generated based on spatial derivatives of the reflectance values of the pixels which remain unmasked by the cloud and land mask. The spatial variability image is thresholded to identify one or more regions within the image as possible ship detection regions.

Optimization Design of Minimum Total Resistance Hull Form Based on CFD Method

NASA Astrophysics Data System (ADS)

Zhang, Bao-ji; Zhang, Sheng-long; Zhang, Hui

2018-06-01

In order to reduce the resistance and improve the hydrodynamic performance of a ship, two hull form design methods are proposed based on the potential flow theory and viscous flow theory. The flow fields are meshed using body-fitted mesh and structured grids. The parameters of the hull modification function are the design variables. A three-dimensional modeling method is used to alter the geometry. The Non-Linear Programming (NLP) method is utilized to optimize a David Taylor Model Basin (DTMB) model 5415 ship under the constraints, including the displacement constraint. The optimization results show an effective reduction of the resistance. The two hull form design methods developed in this study can provide technical support and theoretical basis for designing green ships.

Development of the geoCamera, a System for Mapping Ice from a Ship

NASA Astrophysics Data System (ADS)

Arsenault, R.; Clemente-Colon, P.

2012-12-01

The geoCamera produces maps of the ice surrounding an ice-capable ship by combining images from one or more digital cameras with the ship's position and attitude data. Maps are produced along the ship's path with the achievable width and resolution depending on camera mounting height as well as camera resolution and lens parameters. Our system has produced maps up to 2000m wide at 1m resolution. Once installed and calibrated, the system is designed to operate automatically producing maps in near real-time and making them available to on-board users via existing information systems. The resulting small-scale maps complement existing satellite based products as well as on-board observations. Development versions have temporarily been deployed in Antarctica on the RV Nathaniel B. Palmer in 2010 and in the Arctic on the USCGC Healy in 2011. A permanent system has been deployed during the summer of 2012 on the USCGC Healy. To make the system attractive to other ships of opportunity, design goals include using existing ship systems when practical, using low costs commercial-off-the-shelf components if additional hardware is necessary, automating the process to virtually eliminate adding to the workload of ships technicians and making the software components modular and flexible enough to allow more seamless integration with a ships particular IT system.

The Epidemiology of Operation Stress during Continuing Promise 2011: A Humanitarian Response and Disaster Relief Mission aboard a US Navy Hospital Ship.

PubMed

Scouten, William T; Mehalick, Melissa L; Yoder, Elizabeth; McCoy, Andrea; Brannock, Tracy; Riddle, Mark S

2017-08-01

Introduction Operational stress describes individual behavior in response to the occupational demands and tempo of a mission. The stress response of military personnel involved in combat and peace-keeping missions has been well-described. The spectrum of effect on medical professionals and support staff providing humanitarian assistance, however, is less well delineated. Research to date concentrates mainly on shore-based humanitarian missions. Problem The goal of the current study was to document the pattern of operational stress, describe factors responsible for it, and the extent to which these factors impact job performance in military and civilian participants of Continuing Promise 2011 (CP11), a ship-based humanitarian medical mission. This was a retrospective study of Disease Non-Battle Injury (DNBI) data from the medical sick-call clinic and from weekly self-report questionnaires for approximately 900 US military and civilian mission participants aboard the USNS COMFORT (T-AH 20). The incidence rates and job performance impact of reported Operational Stress/Mental Health (OS/MH) issues and predictors (age, rank, occupation, service branch) of OS/MH issues (depression, anxiety) were analyzed over a 22-week deployment period. Incidence rates of OS/MH complaints from the sick-call clinic were 3.7% (4.5/1,000 persons) and 12.0% (53/1,000 persons) from the self-report questionnaire. The rate of operational stress increased as the mission progressed and fluctuated during the mission according to ship movement. Approximately 57% of the responders reported no impact on job performance. Younger individuals (enlisted ranks E4-6, officer ranks O1-3), especially Air Force service members, those who had spent only one day off ship, and those who were members of specific directorates, reported the highest rates of operational stress. The overall incidence of OS/MH complaints was low in participants of CP11 but was under-estimated by clinic-based reporting. The OS/MH complaints increased as the mission progressed, were more prevalent in certain groups, and appeared to be related to ship's movement. These findings document the pattern of operational stress in a ship-based medical humanitarian mission and confirm unique ship-based stressors. This information may be used by planners of similar missions to develop mitigation strategies for known stressors and by preventive medicine, behavioral health specialists, and mission leaders to develop sensitive surveillance tools to better detect and manage operational stress while on mission. Scouten WT , Mehalick ML , Yoder E , McCoy A , Brannock T , Riddle MS . The epidemiology of operation stress during Continuing Promise 2011: a humanitarian response and disaster relief mission aboard a US Navy hospital ship. Prehosp Disaster Med. 2017;32(4):393-402.

Vibration control of a ship engine system using high-load magnetorheological mounts associated with a new indirect fuzzy sliding mode controller

NASA Astrophysics Data System (ADS)

Phu, Do Xuan; Choi, Seung-Bok

2015-02-01

In this work, a new high-load magnetorheological (MR) fluid mount system is devised and applied to control vibration in a ship engine. In the investigation of vibration-control performance, a new modified indirect fuzzy sliding mode controller is formulated and realized. The design of the proposed MR mount is based on the flow mode of MR fluid, and it includes two separated coils for generating a magnetic field. An optimization process is carried out to achieve maximal damping force under certain design constraints, such as the allowable height of the mount. As an actuating smart fluid, a new plate-like iron-particle-based MR fluid is used, instead of the conventional spherical iron-particle-based MR fluid. After evaluating the field-dependent yield stress of the MR fluid, the field-dependent damping force required to control unwanted vibration in the ship engine is determined. Subsequently, an appropriate-sized MR mount is manufactured and its damping characteristics are evaluated. After confirming the sufficient damping force level of the manufactured MR mount, a medium-sized ship engine mount system consisting of eight MR mounts is established, and its dynamic governing equations are derived. A new modified indirect fuzzy sliding mode controller is then formulated and applied to the engine mount system. The displacement and velocity responses show that the unwanted vibrations of the ship engine system can be effectively controlled in both the axial and radial directions by applying the proposed control methodology.

Radiative Forcing Over Ocean by Ship Wakes

NASA Technical Reports Server (NTRS)

Gatebe, Charles K.; Wilcox, E.; Poudyal, R.; Wang, J.

2011-01-01

Changes in surface albedo represent one of the main forcing agents that can counteract, to some extent, the positive forcing from increasing greenhouse gas concentrations. Here, we report on enhanced ocean reflectance from ship wakes over the Pacific Ocean near the California coast, where we determined, based on airborne radiation measurements that ship wakes can increase reflected sunlight by more than 100%. We assessed the importance of this increase to climate forcing, where we estimated the global radiative forcing of ship wakes to be -0.00014 plus or minus 53% Watts per square meter assuming a global distribution of 32331 ships of size of greater than or equal to 100000 gross tonnage. The forcing is smaller than the forcing of aircraft contrails (-0.007 to +0.02 Watts per square meter), but considering that the global shipping fleet has rapidly grown in the last five decades and this trend is likely to continue because of the need of more inter-continental transportation as a result of economic globalization, we argue that the radiative forcing of wakes is expected to be increasingly important especially in harbors and coastal regions.

Achieving Ships Mission Flexibility Through Designing, Printing And Operating Unmanned Systems With Additive Manufacturing And Delayed Differentiation

DTIC Science & Technology

2016-09-01

the UAV’s reliability in fulfilling the mission as well as the build- time of the UAV. 14. SUBJECT TERMS design , print and operate, DPO...previously. There are opportunities to work on the design of the UAV to reduce the cognitive workload of the service member and time required to “print” and...the need arises to tailor the UAV for the specific mission. The modification of an existing design is expected to take a much shorter time than the

Disturbance of a rare seabird by ship-based tourism in a marine protected area.

PubMed

Marcella, Timothy K; Gende, Scott M; Roby, Daniel D; Allignol, Arthur

2017-01-01

Managers of marine protected areas (MPAs) must often seek ways to allow for visitation while minimizing impacts to the resources they are intended to protect. Using shipboard observers, we quantified the "zone of disturbance" for Kittlitz's and marbled murrelets (Brachyramphus brevirostris and B. marmoratus) exposed to large cruise ships traveling through Glacier Bay National Park, one of the largest MPAs in North America. In the upper reaches of Glacier Bay, where Kittlitz's murrelets predominated, binary logistic regression models predicted that 61% of all murrelets within 850 m perpendicular distance of a cruise ship were disturbed (defined as flushing or diving), whereas in the lower reaches, where marbled murrelets predominated, this percentage increased to 72%. Using survival analysis, murrelets in both reaches were found to react at greater distances when ships approached indirectly, presumably because of the ship's larger profile, suggesting murrelets responded to visual rather than audio cues. No management-relevant covariates (e.g., ship velocity, route distance from shore) were found to be important predictors of disturbance, as distance from ship to murrelet accounted for > 90% of the explained variation in murrelet response. Utilizing previously published murrelet density estimates from Glacier Bay, and applying an average empirical disturbance probability (68%) out to 850 m from a cruise ship's typical route, we estimated that a minimum of 9.8-19.6% of all murrelets in Glacier Bay are disturbed per ship entry. Whether these disturbance levels are inconsistent with Park management objectives, which include conserving wildlife as well as providing opportunities for visitation, depends in large part on whether disturbance events caused by cruise ships have impacts on murrelet fitness, which remains uncertain.

Fast iterative censoring CFAR algorithm for ship detection from SAR images

NASA Astrophysics Data System (ADS)

Gu, Dandan; Yue, Hui; Zhang, Yuan; Gao, Pengcheng

2017-11-01

Ship detection is one of the essential techniques for ship recognition from synthetic aperture radar (SAR) images. This paper presents a fast iterative detection procedure to eliminate the influence of target returns on the estimation of local sea clutter distributions for constant false alarm rate (CFAR) detectors. A fast block detector is first employed to extract potential target sub-images; and then, an iterative censoring CFAR algorithm is used to detect ship candidates from each target blocks adaptively and efficiently, where parallel detection is available, and statistical parameters of G0 distribution fitting local sea clutter well can be quickly estimated based on an integral image operator. Experimental results of TerraSAR-X images demonstrate the effectiveness of the proposed technique.

Design and reliability analysis of DP-3 dynamic positioning control architecture

NASA Astrophysics Data System (ADS)

Wang, Fang; Wan, Lei; Jiang, Da-Peng; Xu, Yu-Ru

2011-12-01

As the exploration and exploitation of oil and gas proliferate throughout deepwater area, the requirements on the reliability of dynamic positioning system become increasingly stringent. The control objective ensuring safety operation at deep water will not be met by a single controller for dynamic positioning. In order to increase the availability and reliability of dynamic positioning control system, the triple redundancy hardware and software control architectures were designed and developed according to the safe specifications of DP-3 classification notation for dynamically positioned ships and rigs. The hardware redundant configuration takes the form of triple-redundant hot standby configuration including three identical operator stations and three real-time control computers which connect each other through dual networks. The function of motion control and redundancy management of control computers were implemented by software on the real-time operating system VxWorks. The software realization of task loose synchronization, majority voting and fault detection were presented in details. A hierarchical software architecture was planed during the development of software, consisting of application layer, real-time layer and physical layer. The behavior of the DP-3 dynamic positioning control system was modeled by a Markov model to analyze its reliability. The effects of variation in parameters on the reliability measures were investigated. The time domain dynamic simulation was carried out on a deepwater drilling rig to prove the feasibility of the proposed control architecture.

Project Exodus

NASA Technical Reports Server (NTRS)

Bryant, Rodney (Compiler); Dillon, Jennifer (Compiler); Grewe, George (Compiler); Mcmorrow, Jim (Compiler); Melton, Craig (Compiler); Rainey, Gerald (Compiler); Rinko, John (Compiler); Singh, David (Compiler); Yen, Tzu-Liang (Compiler)

1990-01-01

A design for a manned Mars mission, PROJECT EXODUS is presented. PROJECT EXODUS incorporates the design of a hypersonic waverider, cargo ship and NIMF (nuclear rocket using indigenous Martian fuel) shuttle lander to safely carry out a three to five month mission on the surface of Mars. The cargo ship transports return fuel, return engine, surface life support, NIMF shuttle, and the Mars base to low Mars orbit (LMO). The cargo ship is powered by a nuclear electric propulsion (NEP) system which allows the cargo ship to execute a spiral trajectory to Mars. The waverider transports ten astronauts to Mars and back. It is launched from the Space Station with propulsion provided by a chemical engine and a delta velocity of 9 km/sec. The waverider performs an aero-gravity assist maneuver through the atmosphere of Venus to obtain a deflection angle and increase in delta velocity. Once the waverider and cargo ship have docked the astronauts will detach the landing cargo capsules and nuclear electric power plant and remotely pilot them to the surface. They will then descend to the surface aboard the NIMF shuttle. A dome base will be quickly constructed on the surface and the astronauts will conduct an exploratory mission for three to five months. They will return to Earth and dock with the Space Station using the waverider.

Modelling the impact of liner shipping network perturbations on container cargo routing: Southeast Asia to Europe application.

PubMed

Achurra-Gonzalez, Pablo E; Novati, Matteo; Foulser-Piggott, Roxane; Graham, Daniel J; Bowman, Gary; Bell, Michael G H; Angeloudis, Panagiotis

2016-06-03

Understanding how container routing stands to be impacted by different scenarios of liner shipping network perturbations such as natural disasters or new major infrastructure developments is of key importance for decision-making in the liner shipping industry. The variety of actors and processes within modern supply chains and the complexity of their relationships have previously led to the development of simulation-based models, whose application has been largely compromised by their dependency on extensive and often confidential sets of data. This study proposes the application of optimisation techniques less dependent on complex data sets in order to develop a quantitative framework to assess the impacts of disruptive events on liner shipping networks. We provide a categorization of liner network perturbations, differentiating between systemic and external and formulate a container assignment model that minimises routing costs extending previous implementations to allow feasible solutions when routing capacity is reduced below transport demand. We develop a base case network for the Southeast Asia to Europe liner shipping trade and review of accidents related to port disruptions for two scenarios of seismic and political conflict hazards. Numerical results identify alternative routing paths and costs in the aftermath of port disruptions scenarios and suggest higher vulnerability of intra-regional connectivity. Copyright © 2016 Elsevier Ltd. All rights reserved.

Heterogeneous distributed databases: A case study

NASA Technical Reports Server (NTRS)

Stewart, Tracy R.; Mukkamala, Ravi

1991-01-01

Alternatives are reviewed for accessing distributed heterogeneous databases and a recommended solution is proposed. The current study is limited to the Automated Information Systems Center at the Naval Sea Combat Systems Engineering Station at Norfolk, VA. This center maintains two databases located on Digital Equipment Corporation's VAX computers running under the VMS operating system. The first data base, ICMS, resides on a VAX11/780 and has been implemented using VAX DBMS, a CODASYL based system. The second database, CSA, resides on a VAX 6460 and has been implemented using the ORACLE relational database management system (RDBMS). Both databases are used for configuration management within the U.S. Navy. Different customer bases are supported by each database. ICMS tracks U.S. Navy ships and major systems (anti-sub, sonar, etc.). Even though the major systems on ships and submarines have totally different functions, some of the equipment within the major systems are common to both ships and submarines.

46 CFR 111.15-3 - Battery categories.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Battery categories. 111.15-3 Section 111.15-3 Shipping... REQUIREMENTS Storage Batteries and Battery Chargers: Construction and Installation § 111.15-3 Battery categories. (a) A battery installation is classified as one of three types, based upon power output of the...

Economic Impacts of the Category 3 Marine Rule on Great Lakes Shipping

EPA Science Inventory

This is a scenario-based economic assessment of the impacts of EPA’s Category 3 Marine Diesel Engines Rule on certain cargo movements in the Great Lakes shipping network. During the proposed phase of the rulemaking, Congress recommended that EPA conduct such a study, and EPA wil...

Discrete Event Simulation of a Suppression of Enemy Air Defenses (SEAD) Mission

DTIC Science & Technology

2008-03-01

component-based DES developed in Java® using the Simkit simulation package. Analysis of ship self air defense system selection ( Turan , 1999) is another...Institute of Technology, Wright-Patterson AFB OH, March 2003 (ADA445279 ) Turan , Bulent. A Comparative Analysis of Ship Self Air Defense (SSAD) Systems

46 CFR 111.15-3 - Battery categories.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Battery categories. 111.15-3 Section 111.15-3 Shipping... REQUIREMENTS Storage Batteries and Battery Chargers: Construction and Installation § 111.15-3 Battery categories. (a) A battery installation is classified as one of three types, based upon power output of the...

46 CFR 111.15-3 - Battery categories.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Battery categories. 111.15-3 Section 111.15-3 Shipping... REQUIREMENTS Storage Batteries and Battery Chargers: Construction and Installation § 111.15-3 Battery categories. (a) A battery installation is classified as one of three types, based upon power output of the...

46 CFR 111.15-3 - Battery categories.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Battery categories. 111.15-3 Section 111.15-3 Shipping... REQUIREMENTS Storage Batteries and Battery Chargers: Construction and Installation § 111.15-3 Battery categories. (a) A battery installation is classified as one of three types, based upon power output of the...

46 CFR 111.15-3 - Battery categories.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Battery categories. 111.15-3 Section 111.15-3 Shipping... REQUIREMENTS Storage Batteries and Battery Chargers: Construction and Installation § 111.15-3 Battery categories. (a) A battery installation is classified as one of three types, based upon power output of the...

Hydrodynamic Interactions during Launch and Recovery of a Small Boat from a Ship in a Seaway

DTIC Science & Technology

2014-11-28

during launch and recovery. The RHIB is based on a Zodiac H935, with properties given in Table 1 when loaded with 12 person- nel. Figure 1 shows the hull...and recovery of a small craft from a larger ship, wave-induced motions of the larger ship will influence dy- namic loads on the crane. The motions of... the small craft will be a major determinant of the safety of onboard personnel. This paper exam- ines wave-induced motions during launch and recovery

Impact of cryopreservation on tetramer, cytokine flow cytometry, and ELISPOT

PubMed Central

Maecker, Holden T; Moon, James; Bhatia, Sonny; Ghanekar, Smita A; Maino, Vernon C; Payne, Janice K; Kuus-Reichel, Kristine; Chang, Jennie C; Summers, Amanda; Clay, Timothy M; Morse, Michael A; Lyerly, H Kim; DeLaRosa, Corazon; Ankerst, Donna P; Disis, Mary L

2005-01-01

Background Cryopreservation of PBMC and/or overnight shipping of samples are required for many clinical trials, despite their potentially adverse effects upon immune monitoring assays such as MHC-peptide tetramer staining, cytokine flow cytometry (CFC), and ELISPOT. In this study, we compared the performance of these assays on leukapheresed PBMC shipped overnight in medium versus cryopreserved PBMC from matched donors. Results Using CMV pp65 peptide pool stimulation or pp65 HLA-A2 tetramer staining, there was significant correlation between shipped and cryopreserved samples for each assay (p ≤ 0.001). The differences in response magnitude between cryopreserved and shipped PBMC specimens were not significant for most antigens and assays. There was significant correlation between CFC and ELISPOT assay using pp65 peptide pool stimulation, in both shipped and cryopreserved samples (p ≤ 0.001). Strong correlation was observed between CFC (using HLA-A2-restricted pp65 peptide stimulation) and tetramer staining (p < 0.001). Roughly similar sensitivity and specificity were observed between the three assays and between shipped and cryopreserved samples for each assay. Conclusion We conclude that all three assays show concordant results on shipped versus cryopreserved specimens, when using a peptide-based readout. The assays are also concordant with each other in pair wise comparisons using equivalent antigen systems. PMID:16026627

Adaptive Robust Output Feedback Control for a Marine Dynamic Positioning System Based on a High-Gain Observer.

PubMed

Du, Jialu; Hu, Xin; Liu, Hongbo; Chen, C L Philip

2015-11-01

This paper develops an adaptive robust output feedback control scheme for dynamically positioned ships with unavailable velocities and unknown dynamic parameters in an unknown time-variant disturbance environment. The controller is designed by incorporating the high-gain observer and radial basis function (RBF) neural networks in vectorial backstepping method. The high-gain observer provides the estimations of the ship position and heading as well as velocities. The RBF neural networks are employed to compensate for the uncertainties of ship dynamics. The adaptive laws incorporating a leakage term are designed to estimate the weights of RBF neural networks and the bounds of unknown time-variant environmental disturbances. In contrast to the existing results of dynamic positioning (DP) controllers, the proposed control scheme relies only on the ship position and heading measurements and does not require a priori knowledge of the ship dynamics and external disturbances. By means of Lyapunov functions, it is theoretically proved that our output feedback controller can control a ship's position and heading to the arbitrarily small neighborhood of the desired target values while guaranteeing that all signals in the closed-loop DP control system are uniformly ultimately bounded. Finally, simulations involving two ships are carried out, and simulation results demonstrate the effectiveness of the proposed control scheme.

Management Principles to be Considered for Implementing a Data Base Management System Aboard U.S. (United States) Naval Ships under the Shipboard Non-Tactical ADP (Automated Data Processing) Program.

DTIC Science & Technology

1982-12-01

Data Base Management System Aboard U.S. Naval Ships Under the Shipboard Non-tactical ADP Program by Robert Harrison Dixon December 1982 Thesis Advisor...OF REPORT a PERIOD COVIAOtt Management Principles to be Considered for Master’s Thesis Implementing a Data Base Management System December 1982 Aboard...NOTES is. KEY s0mas (Coelte on revrs side of 0..e..mp am iNe or "Neo 00111) Data Base Management System , DBMS, SNAP, SNAP I, SNAP II, Information

Department of the Navy Supporting Data for Fiscal Year 1983 Budget Estimates Descriptive Summaries Submitted to Congress February 1982. Research, Development, Test and Evaluation, Navy. Book 3 of 3. Tactical Programs, Intelligence & Communications, Management & Support

DTIC Science & Technology

1982-02-01

For these data elements, Initial Milestone 11 values were established as the Flanning Estimate (PE) with the Development Estimate ( DE ) to he based ...development of improved forensic collection techniques for Naval Investigative Agents on ships and overseas bases . As this is a continuing program, the above...overseas bases ), and continue development of improved forensic collection techniques for Naval Investigative Agents on ships and overseas baszs. 4. (U) FY

Capability of geometric features to classify ships in SAR imagery

NASA Astrophysics Data System (ADS)

Lang, Haitao; Wu, Siwen; Lai, Quan; Ma, Li

2016-10-01

Ship classification in synthetic aperture radar (SAR) imagery has become a new hotspot in remote sensing community for its valuable potential in many maritime applications. Several kinds of ship features, such as geometric features, polarimetric features, and scattering features have been widely applied on ship classification tasks. Compared with polarimetric features and scattering features, which are subject to SAR parameters (e.g., sensor type, incidence angle, polarization, etc.) and environment factors (e.g., sea state, wind, wave, current, etc.), geometric features are relatively independent of SAR and environment factors, and easy to be extracted stably from SAR imagery. In this paper, the capability of geometric features to classify ships in SAR imagery with various resolution has been investigated. Firstly, the relationship between the geometric feature extraction accuracy and the SAR imagery resolution is analyzed. It shows that the minimum bounding rectangle (MBR) of ship can be extracted exactly in terms of absolute precision by the proposed automatic ship-sea segmentation method. Next, six simple but effective geometric features are extracted to build a ship representation for the subsequent classification task. These six geometric features are composed of length (f1), width (f2), area (f3), perimeter (f4), elongatedness (f5) and compactness (f6). Among them, two basic features, length (f1) and width (f2), are directly extracted based on the MBR of ship, the other four are derived from those two basic features. The capability of the utilized geometric features to classify ships are validated on two data set with different image resolutions. The results show that the performance of ship classification solely by geometric features is close to that obtained by the state-of-the-art methods, which obtained by a combination of multiple kinds of features, including scattering features and geometric features after a complex feature selection process.

Multiple quay cranes scheduling for double cycling in container terminals

PubMed Central

Chu, Yanling; Zhang, Xiaoju; Yang, Zhongzhen

2017-01-01

Double cycling is an efficient tool to increase the efficiency of quay crane (QC) in container terminals. In this paper, an optimization model for double cycling is developed to optimize the operation sequence of multiple QCs. The objective is to minimize the makespan of the ship handling operation considering the ship balance constraint. To solve the model, an algorithm based on Lagrangian relaxation is designed. Finally, we compare the efficiency of the Lagrangian relaxation based heuristic with the branch-and-bound method and a genetic algorithm using instances of different sizes. The results of numerical experiments indicate that the proposed model can effectively reduce the unloading and loading times of QCs. The effects of the ship balance constraint are more notable when the number of QCs is high. PMID:28692699

Multiple quay cranes scheduling for double cycling in container terminals.

PubMed

Chu, Yanling; Zhang, Xiaoju; Yang, Zhongzhen

2017-01-01

Double cycling is an efficient tool to increase the efficiency of quay crane (QC) in container terminals. In this paper, an optimization model for double cycling is developed to optimize the operation sequence of multiple QCs. The objective is to minimize the makespan of the ship handling operation considering the ship balance constraint. To solve the model, an algorithm based on Lagrangian relaxation is designed. Finally, we compare the efficiency of the Lagrangian relaxation based heuristic with the branch-and-bound method and a genetic algorithm using instances of different sizes. The results of numerical experiments indicate that the proposed model can effectively reduce the unloading and loading times of QCs. The effects of the ship balance constraint are more notable when the number of QCs is high.

A Cost Comparison Between Active and Naval Reserve Force FFG 7 Class Ships

DTIC Science & Technology

1993-06-01

so in our hypothetical depreciation schedule 1/30th of the depreciable cost would be expensed each year. Under GAAP , the historical cost of the asset...and Support Costs (VAMOSC) data base provided by the* aval Center For Cost Analysis. The thesis also sets up theoretical depreciation schedules for...VAMOSC) data base provided by the Naval Center for Cost Analysis. The thesis also sets up theoretical depreciation schedules for selected ships to

A comprehensive inventory of the ship traffic exhaust emissions in the Baltic Sea from 2006 to 2009.

PubMed

Jalkanen, Jukka-Pekka; Johansson, Lasse; Kukkonen, Jaakko

2014-04-01

This study addresses the exhaust emissions of CO₂, NO(x), SO(x), CO, and PM(2.5) originated from Baltic Sea shipping in 2006-2009. Numerical results have been computed using the Ship Traffic Emissions Assessment Model. This model is based on the messages of the automatic identification system (AIS), which enable the positioning of ships with a high spatial resolution. The NO(x) emissions in 2009 were approximately 7 % higher than in 2006, despite the economic recession. However, the SO(x) emissions in 2009 were approximately 14 % lower, when compared to those in 2006, mainly caused by the fuel requirements of the SO(x) emission control area (SECA) which became effective in May 2006, but affected also by changes in ship activity. Results are presented on the differential geographic distribution of shipping emissions before (Jan-April 2006) and after (Jan-April 2009) the SECA regulations. The predicted NO(x) emissions in 2009 substantially exceeded the emissions in 2006 along major ship routes and at numerous harbors, mostly due to the continuous increase in the number of small vessels that use AIS transmitters. Although the SO(x) emissions have been reduced in 2009 in most major ship routes, these have increased in the vicinity of some harbors and on some densely trafficked routes. A seasonal variation of emissions is also presented, as well as the distribution of emissions in terms of vessel flag state, type, and weight.

Wallops Ship Surveillance System

NASA Technical Reports Server (NTRS)

Smith, Donna C.

2011-01-01

Approved as a Wallops control center backup system, the Wallops Ship Surveillance Software is a day-of-launch risk analysis tool for spaceport activities. The system calculates impact probabilities and displays ship locations relative to boundary lines. It enables rapid analysis of possible flight paths to preclude the need to cancel launches and allow execution of launches in a timely manner. Its design is based on low-cost, large-customer- base elements including personal computers, the Windows operating system, C/C++ object-oriented software, and network interfaces. In conformance with the NASA software safety standard, the system is designed to ensure that it does not falsely report a safe-for-launch condition. To improve the current ship surveillance method, the system is designed to prevent delay of launch under a safe-for-launch condition. A single workstation is designated the controller of the official ship information and the official risk analysis. Copies of this information are shared with other networked workstations. The program design is divided into five subsystems areas: 1. Communication Link -- threads that control the networking of workstations; 2. Contact List -- a thread that controls a list of protected item (ocean vessel) information; 3. Hazard List -- threads that control a list of hazardous item (debris) information and associated risk calculation information; 4. Display -- threads that control operator inputs and screen display outputs; and 5. Archive -- a thread that controls archive file read and write access. Currently, most of the hazard list thread and parts of other threads are being reused as part of a new ship surveillance system, under the SureTrak project.

46 CFR 64.81 - 30-month inspection of an MPT.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false 30-month inspection of an MPT. 64.81 Section 64.81 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING MARINE PORTABLE TANKS... external examination for— (i) Corrosion; (ii) Cracking of base material; and (iii) Weld defects; and (2) A...

46 CFR 128.450 - Liquid-mud systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Liquid-mud systems. 128.450 Section 128.450 Shipping...: EQUIPMENT AND SYSTEMS Design Requirements for Specific Systems § 128.450 Liquid-mud systems. (a) Liquid-mud... this chapter. (b) Tanks for oil-based liquid mud must be fitted with tank vents equipped with flame...

33 CFR 165.805 - Security Zones; Calcasieu River and Ship Channel, Louisiana.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 2 2012-07-01 2012-07-01 false Security Zones; Calcasieu River... § 165.805 Security Zones; Calcasieu River and Ship Channel, Louisiana. (a) Location. (1) The following areas are designated as fixed security zones (all coordinates are based upon North American Datum of...

33 CFR 165.805 - Security Zones; Calcasieu River and Ship Channel, Louisiana.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 2 2013-07-01 2013-07-01 false Security Zones; Calcasieu River... § 165.805 Security Zones; Calcasieu River and Ship Channel, Louisiana. (a) Location. (1) The following areas are designated as fixed security zones (all coordinates are based upon North American Datum of...

33 CFR 165.805 - Security Zones; Calcasieu River and Ship Channel, Louisiana.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 2 2014-07-01 2014-07-01 false Security Zones; Calcasieu River... § 165.805 Security Zones; Calcasieu River and Ship Channel, Louisiana. (a) Location. (1) The following areas are designated as fixed security zones (all coordinates are based upon North American Datum of...

33 CFR 165.805 - Security Zones; Calcasieu River and Ship Channel, Louisiana.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 2 2011-07-01 2011-07-01 false Security Zones; Calcasieu River... § 165.805 Security Zones; Calcasieu River and Ship Channel, Louisiana. (a) Location. (1) The following areas are designated as fixed security zones (all coordinates are based upon North American Datum of...

Advanced error-prediction LDPC with temperature compensation for highly reliable SSDs

NASA Astrophysics Data System (ADS)

Tokutomi, Tsukasa; Tanakamaru, Shuhei; Iwasaki, Tomoko Ogura; Takeuchi, Ken

2015-09-01

To improve the reliability of NAND Flash memory based solid-state drives (SSDs), error-prediction LDPC (EP-LDPC) has been proposed for multi-level-cell (MLC) NAND Flash memory (Tanakamaru et al., 2012, 2013), which is effective for long retention times. However, EP-LDPC is not as effective for triple-level cell (TLC) NAND Flash memory, because TLC NAND Flash has higher error rates and is more sensitive to program-disturb error. Therefore, advanced error-prediction LDPC (AEP-LDPC) has been proposed for TLC NAND Flash memory (Tokutomi et al., 2014). AEP-LDPC can correct errors more accurately by precisely describing the error phenomena. In this paper, the effects of AEP-LDPC are investigated in a 2×nm TLC NAND Flash memory with temperature characterization. Compared with LDPC-with-BER-only, the SSD's data-retention time is increased by 3.4× and 9.5× at room-temperature (RT) and 85 °C, respectively. Similarly, the acceptable BER is increased by 1.8× and 2.3×, respectively. Moreover, AEP-LDPC can correct errors with pre-determined tables made at higher temperatures to shorten the measurement time before shipping. Furthermore, it is found that one table can cover behavior over a range of temperatures in AEP-LDPC. As a result, the total table size can be reduced to 777 kBytes, which makes this approach more practical.

Ship emissions and the use of current air cleaning technology: contributions to air pollution and acidification in the Baltic Sea

NASA Astrophysics Data System (ADS)

Claremar, Björn; Haglund, Karin; Rutgersson, Anna

2017-10-01

The shipping sector is a significant contributor to emissions of air pollutants in marine and coastal regions. In order to achieve sustainable shipping, primarily through new regulations and techniques, greater knowledge of dispersion and deposition of air pollutants is required. Regional model calculations of the dispersion and concentration of sulfur, nitrogen, and particulate matter, as well as deposition of oxidized sulfur and nitrogen from the international maritime sector in the Baltic Sea and the North Sea, have been made for the years 2011 to 2013. The contribution from shipping is highest along shipping lanes and near large ports for concentration and dry deposition. Sulfur is the most important pollutant coupled to shipping. The contribution of both SO2 concentration and dry deposition of sulfur represented up to 80 % of the total in some regions. WHO guidelines for annual concentrations were not trespassed for any analysed pollutant, other than PM2.5 in the Netherlands, Belgium, and central Poland. However, due to the resolution of the numerical model, 50 km × 50 km, there may be higher concentrations locally close to intense shipping lanes. Wet deposition is more spread and less sensitive to model resolution. The contribution of wet deposition of sulfur and nitrogen from shipping was up to 30 % of the total wet deposition. Comparison of simulated to measured concentration at two coastal stations close to shipping lanes showed some underestimations and missed maximums, probably due to resolution of the model and underestimated ship emissions. A change in regulation for maximum sulfur content in maritime fuel, in 2015 from 1 to 0.1 %, decreases the atmospheric sulfur concentration and deposition significantly. However, due to costs related to refining, the cleaning of exhausts through scrubbers has become a possible economic solution. Open-loop scrubbers meet the air quality criteria but their consequences for the marine environment are largely unknown. The resulting potential of future acidification in the Baltic Sea, both from atmospheric deposition and from scrubber water along the shipping lanes, based on different assumptions about sulfur content in fuel, scrubber usage, and increased shipping density has been assessed. The increase in deposition for different shipping and scrubber scenarios differs for the basins in the Baltic Sea, with highest potential of acidification in the southern basins with high traffic. The proportion of ocean-acidifying sulfur from ships increases when taking scrubber water into account and the major reason for increasing acidifying nitrogen from ships is increasing ship traffic. Also, with the implementation of emission control for nitrogen, the effect of scrubbers on acidification is evident. This study also generates a database of shipping and scrubber scenarios for atmospheric deposition and scrubber exhaust from the period 2011 to 2050.

KSC-02pd1537

NASA Image and Video Library

2002-10-15

KENNEDY SPACE CENTER, FLA. -- Workers on the deck of the Liberty Star, one of NASA's solid rocket booster retrieval ships, help guide sonar mapping equipment toward the side of the ship. The equipment will be attached to the ship's hull for an eight-day expedition surveying deep-water coral reefs on the Oculina Banks off eastern Florida. NASA joins the National Oceanic and Atmospheric Administration (NOAA) and other ocean scientists for the sophisticated mapping system that will provide the first high-resolution, three-dimensional map of the Oculina Banks. The survey results are expected to guide another expedition in Spring 2003, using NASA's ship, when the reef fish spawn. Also used will be NASA's underwater robot and an acoustic hydrophone system for listening to fish and vessel noise. Dive sites will be chosen based on the new charts.

Systemic risk and causality dynamics of the world international shipping market

NASA Astrophysics Data System (ADS)

Zhang, Xin; Podobnik, Boris; Kenett, Dror Y.; Eugene Stanley, H.

2014-12-01

Various studies have reported that many economic systems have been exhibiting an increase in the correlation between different market sectors, a factor that exacerbates the level of systemic risk. We measure this systemic risk of three major world shipping markets, (i) the new ship market, (ii) the second-hand ship market, and (iii) the freight market, as well as the shipping stock market. Based on correlation networks during three time periods, that prior to the financial crisis, during the crisis, and after the crisis, minimal spanning trees (MSTs) and hierarchical trees (HTs) both exhibit complex dynamics, i.e., different market sectors tend to be more closely linked during financial crisis. Brownian distance correlation and Granger causality test both can be used to explore the directional interconnectedness of market sectors, while Brownian distance correlation captures more dependent relationships, which are not observed in the Granger causality test. These two measures can also identify and quantify market regression periods, implying that they contain predictive power for the current crisis.

Ship wakes and spectrograms: mathematical modelling and experimental data for finite-depth flows

NASA Astrophysics Data System (ADS)

McCue, Scott; Pethiyagoda, Ravindra; Moroney, Timothy; Macfarlane, Gregor; Binns, Jonathan

2017-11-01

We are concerned with how properties of a ship wake can be extracted from surface height data collected at a single point as the ship travels past. The tool we use is a spectrogram, which is a heat map that visualises the time-dependent frequency spectrum of the surface height signal. In this talk, the focus will be on presenting the theoretical framework which involves an idealised mathematical model with a pressure distribution applied to the surface. A geometric argument based on linear water wave theory provides encouraging results for both subcritical and supercritical flow regimes. We then summarise some recent findings obtained by comparing our analysis to experimental data collected at the Australian Maritime College for various sailing speeds and hull shapes*. Our work has the potential to inform ship design, the detection of irregular vessels, and how coastal damage is attributed to specific vessels in shipping channels. We acknowledge support of the Australian Research Council via the Discovery Project DP140100933.

Shungnak Energy Configuration Options.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rosewater, David Martin; Eddy, John P.

Power systems in rural Alaska villages face a unique combination of challenges that can increase the cost of energy and lowers energy supply reliability. In the case of the remote village of Shungnak, diesel and heating fuel is either shipped in by barge or flown in by aircraft. This report presents a technical analysis of several energy infrastructure upgrade and modification options to reduce the amount of fuel consumed by the community of Shungnak. Reducing fuel usage saves money and makes the village more resilient to disruptions in fuel supply. The analysis considers demand side options, such as energy efficiency,more » alongside the installation of wind and solar power generation options. Some novel approaches are also considered including battery energy storage and the use of electrical home heating stoves powered by renewable generation that would otherwise be spilled and wasted. This report concludes with specific recommendations for Shungnak based on economic factors, and fuel price sensitivity. General conclusions are also included to support future work analyzing similar energy challenges in remote arctic regions.« less

Extending the littoral battlespace (ELB)

NASA Astrophysics Data System (ADS)

McKinney, Edward J.

1999-07-01

The ELB program is a joint Advanced Concept Technology Demonstration funded by the Navy, Marine Corps and the Office of the Secretary of Defence, and managed by the Naval Research. ELB is based on the new warfare paradigm defined by 'joint vision 2010, and on concepts developed by the Navy and Marine Corps in 'From the Sea', 'Forward...from the Sea', 'Ship to Objective Maneuver (STOM)', and 'Operational Maneuver from the Sea'. The objective of ELB is to demonstrate effective operation of dispersed forces in a variety of littoral environments, and to provide those forces timely remote fire support. Successful operation will depend on achieving a common situational awareness among a mobile, distributed command and control, a shortened sensor- to-shooter timeline, and effective utilization of all information source. The glue to hold this system of systems together is a reliable wide band communications system and network infrastructure. This paper will describe the overall architecture of ELB and focus on the core command and control functions associated with achieving a common situational awareness.

A fully automated FTIR system for remote sensing of greenhouse gases in the tropics

NASA Astrophysics Data System (ADS)

Geibel, M. C.; Gerbig, C.; Feist, D. G.

2010-07-01

This article introduces a new fully automated FTIR system that is part of the Total Carbon Column Observing Network. It will provide continuous ground-based measurements of column-averaged volume mixing ratio for CO2, CH4 and several other greenhouse gases in the tropics. Housed in a 20-foot shipping container it was developed as a transportable system that could be deployed almost anywhere in the world. We describe the automation concept which relies on three autonomous subsystems and their interaction. Crucial components like a sturdy and reliable solar tracker dome are described in detail. First results of total column measurements at Jena, Germany show that the instrument works well and can provide diurnal as well as seasonal cycle for CO2. Instrument line shape measurements with an HCl cell suggest that the instrument stays well-aligned over several months. After a short test campaign for side by side intercomaprison with an existing TCCON instrument in Australia, the system will be transported to its final destination Ascension Island.

Crystal growth and materials research in photovoltaics: progress and challenges

NASA Astrophysics Data System (ADS)

Surek, Thomas

2005-02-01

Photovoltaics (PV) is solar electric power—a semiconductor-based technology that converts sunlight to electricity. Three decades of research has led to the discovery of new materials and devices and new processing techniques for low-cost manufacturing. This has resulted in improved sunlight-to-electricity conversion efficiencies, improved outdoor reliability, and lower module and system costs. The manufacture and sale of PV has grown into a $5 billion industry worldwide, with more than 740 megawatts of PV modules shipped in 2003. This paper reviews the significant progress that has occurred in PV materials and devices research over the past 30 years, focusing on the advances in crystal growth and materials research, and examines the challenges to reaching the ultimate potential of current-generation (crystalline silicon), next-generation (thin films and concentrators), and future-generation PV technologies. The latter includes innovative materials and device concepts that hold the promise of significantly higher conversion efficiencies and/or much lower costs.

Constraints on Eurasian ship NOx emissions using OMI NO2 observations and GEOS-Chem

NASA Astrophysics Data System (ADS)

Vinken, Geert C. M.; Boersma, Folkert; van Donkelaar, Aaron; Zhang, Lin

2013-04-01

Ships emit large quantities of nitrogen oxides (NOx = NO + NO2), important precursors for ozone (O3) and particulate matter formation. Ships burn low-grade marine heavy fuel due to the limited regulations that exist for the maritime sector in international waters. Previous studies showed that global ship NOx emission inventories amount to 3.0-10.4 Tg N per year (15-30% of total NOx emissions), with most emissions close to land and affecting air quality in densely populated coastal regions. Bottom-up inventories depend on the extrapolation of a relatively small number of measurements that are often unable to capture annual emission changes and can suffer from large uncertainties. Satellites provide long-term, high-resolution retrievals that can be used to improve emission estimates. In this study we provide top-down constraints on ship NOx emissions in major European ship routes, using observed NO2 columns from the Ozone Monitoring Instrument (OMI) and NO2 columns simulated with the nested (0.5°×0.67°) version of the GEOS-Chem chemistry transport model. We use a plume-in-grid treatment of ship NOx emissions to account for in-plume chemistry in our model. We ensure consistency between the retrievals and model simulations by using the high-resolution GEOS-Chem NO2 profiles as a priori. We find evidence that ship emissions in the Mediterranean Sea are geographically misplaced by up to 150 km and biased high by a factor of 4 as compared to the most recent (EMEP) ship emission inventory. Better agreement is found over the shipping lane between Spain and the English Channel. We extend our approach and also provide constraints for major ship routes in the Red Sea and Indian Ocean. Using the full benefit of the long-term retrieval record of OMI, we present a new Eurasian ship emission inventory for the years 2005 to 2010, based on the EMEP and AMVER-ICOADS inventories, and top-down constraints from the satellite retrievals. Our work shows that satellite retrievals can improve the characterization of emission locations, magnitudes and trends over sparsely monitored areas such as seas or oceans.

An integrated sea monitoring system based on a X-band wave radar to support the removal activities of the Costa Concordia wreck.

NASA Astrophysics Data System (ADS)

Gozzini, Bernardo; Serafino, Francesco; Lugni, Claudio; Antonini, Andrea; Costanza, Letizia; Orlandi, Andrea; Arturi, Daniele; Ludeno, Giovanni; Natale, Antonio; Soldovieri, Francesco; Ortolani, Alberto; Brandini, Carlo

2013-04-01

The planning and management of different types of operations at sea requires a number of sea state data as much in real-time as possible, for rapid and effective response to different situations. This need is particularly strong in emergency management practices, in accidents due to man-made or natural causes, that require the planning of civil protection activities (such as search-and-rescue, cleaning of pollution, ship recovery), transport planning etc. The use of X-band radar technology nowadays provides great advantages over traditional in-situ and satellite-based techniques for sea state measuring, to update information on waves and currents over a sea area with high spatial and temporal resolution. Other advantages include a good spatial coverage around the area of interest, the flexibility of use, the capacity to provide, on-demand and when necessary, complementary information (possible oil spills detection, integration with VTS, etc.). X-band coastal radars (so-called "wave-radars") are widely used in the monitoring of large marine areas, in integration with in-situ measurements, satellites and other radar types (HF), as a key element of the observational component of present operational oceanography systems. Outside of these systems, the use of this technology to support emergency management practices is very promising for both the quality and quantity of available parameters, and for an easy integration with all other available monitoring and forecasting tools. A case study particularly relevant is offered by the presence of the Costa Concordia ship near the Giglio Island. The management of this disaster has requested at an early stage a large number of data to support the monitoring of marine environment around the ship, e.g. to optimally plan water samples. In the next and present phase, to support the highly risky and costly activities linked to the wreck removal, which are extremely sea-state dependent, the installation of a wave-radar allows to detect, in real-time and with high revisiting time, waves and currents in the area surrounding the wreck. In addition wave spectra measures allow to check the reliability of present wave forecasting models, which are unlikely to represent the local and coastal scales of interest and therefore require a continuous process of verification, calibration and quality control. Similar considerations can be made for the reconstruction of marine currents at a local scale, whose uncertainty is inherently greater. The integration of X-band radar data with in-situ data has allowed to optimally calibrate the data itself (especially for what concerns the significant wave height) and to provide a local scale observation system which proved to be fundamental to support the work of continuous sea state monitoring and forecasting around the area of the disaster. The observation system at Giglio is a kind of laboratory unique in its kind, to test the reliability of the wave and hydrodynamic models at a local scale, to assess our present ability to use X-band radars for emergency management activities, and to evaluate the response capacity of such practices to the actual needs of involved stakeholders and private users.

Recent advances in cooled-semen technology.

PubMed

Aurich, Christine

2008-09-01

The majority of horse registries approve the use of artificial insemination, and horse breeding has widely taken benefit from the use of cooled-stored semen. New insights into cooled-semen technology open possibilities to reduce problems such as impaired semen quality after cooled-storage in individual stallions. The stallion itself has major impacts on quality and fertility of cooled-stored semen. Dietary supplementation of antioxidants and polyunsaturated fatty acids improves semen quality in a variety of species, but only few studies on this topic exist in the horse. Proper semen collection and handling is the main key to the maintenance of semen quality during cooled-storage. Semen collection should be achieved by minimal sexual stimulation with a single mount; this results in high sperm concentration, low content of seminal plasma and minimal contamination with bacteria. Milk-based semen extenders are most popular for semen processing and storage. The development of more defined extenders containing only the beneficial milk ingredients has made extender quality more constant and reliable. Semen is often centrifuged to decrease the seminal plasma content. Centrifugation results in a recovery rate of only 75% of spermatozoa in the semen pellet. Recovery rates after centrifugation may be improved with use of a "cushion technique" allowing higher centrifugation force and duration. However, this is not routinely used in cooled-semen technology. After slow-cooling, semen-storage and shipping is best performed at 5 degrees C, maintaining semen motility, membrane integrity and DNA integrity for up to 40 h after collection. Shipping containers created from Styrofoam boxes provide maintenance of semen quality at low cost.

Satellite Ocean Color Validation Using Merchant Ships. Chapter 10

NASA Technical Reports Server (NTRS)

Frouin, Robert; Cutchin, David L.; Deschamps, Pierre-Yves

2001-01-01

A collaborative measurement program for evaluating satellite-derived ocean color has been developed based on ships of opportunity (merchant, oceanographic) and specific instrumentation, the SIMBAD radiometer. The purpose of the measurement program is to complement, in a cost-effective way, dedicated evaluation experiments at sea, which are expensive, cannot be carried out over the full range of expected oceanic and atmospheric conditions, and generally provide a few match-ups. Ships participate in the program on a volunteer basis or at a very small cost, and measurement procedures do not interfere with other ship activities. The SIMBAD radiometer is a portable, easy-to-operate instrument that measures the basic ocean color variables, namely aerosol optical thickness and water-leaving radiance, in typical spectral bands of ocean-color sensors, i.e., 443, 490, 560, 670, and 870 nm. Measuring these variables at the time of satellite overpass is usually sufficient to verify satellite-derived ocean color and to evaluate atmospheric correction algorithms. Any ordinary crew can learn quickly how to make measurements. Importantly, the ship is not required to stop, making it possible to collect data along regular routes traveled by merchant ships in the world's oceans.

Hedging the financial risk from water scarcity for Great Lakes shipping

NASA Astrophysics Data System (ADS)

Meyer, Eliot S.; Characklis, Gregory W.; Brown, Casey; Moody, Paul

2016-01-01

Low water levels in the Great Lakes have recently had significant financial impacts on the region's commercial shipping, which transports hundreds of millions of dollars' worth of bulk goods each year. Cargo capacity is a function of a ship's draft, the distance between water level and the ship's bottom, and lower water levels force ships to reduce cargo loads to prevent running aground in shallow harbors and locks. Financial risk transfer instruments, such as index-based insurance contracts, may provide an adaptable method for managing these financial risks. In this work, a relationship between water levels and shipping revenues is developed and used in an actuarial analysis of the frequency and magnitude of revenue losses. This analysis is used to develop a standardized suite of binary financial contracts, which are indexed to water levels and priced according to predefined thresholds. These contracts are then combined to form hedging portfolios with different objectives for the shippers. Results suggest that binary contracts could substantially reduce the risk of financial losses during low lake level periods and at a relatively low cost of only one to three percent of total revenues, depending on coverage level.

Emissions of NOx, SO2, CO, and HCHO from commercial marine shipping during Texas Air Quality Study (TexAQS) 2006

NASA Astrophysics Data System (ADS)

Williams, E. J.; Lerner, B. M.; Murphy, P. C.; Herndon, S. C.; Zahniser, M. S.

2009-11-01

We report measurements of NOx, SO2, CO, and HCHO mass-based emission factors from more than 200 commercial vessel encounters in the Gulf of Mexico and the Houston-Galveston region of Texas during August and September, 2006. For underway ships, bulk freight carriers have the highest average NOx emissions at ˜87 g NOx (kg fuel)-1, followed by tanker ships at ˜79 g NOx (kg fuel)-1, while container carriers, passenger ships, and tugs all emit an average of about ˜60 g NOx (kg fuel)-1. Emission of NOx from stationary vessels was lower, except for container ships and tugs, and likely reflects use of medium-speed diesel engines. Overall, our mean NOx emission factors are 10-15% lower than published data. Average emission of SO2 was lower for passenger ships and tugs and tows (6-7 g SO2 (kg fuel)-1) than for larger cargo vessels (20-30 g SO2 (kg fuel)-1). Our data for large cargo ships in this region indicate an average residual fuel sulfur content of ˜1.4% which is a factor of two lower than the global average of 2.7%. Emission of CO was low for all categories (7-16 g CO (kg fuel)-1), although our mean overall CO emission factor is about 10% higher than published data. Emission of HCHO was less than 5% that of CO. Despite considerable variability, no functional relationships, such as emissions changes with engine speed or load, could be discerned. Comparison of emission factors from ships to those from other sources suggests ship emissions in this region cannot be ignored.

Constraining the ship contribution to the aerosol of the central Mediterranean

NASA Astrophysics Data System (ADS)

Becagli, Silvia; Anello, Fabrizio; Bommarito, Carlo; Cassola, Federico; Calzolai, Giulia; Di Iorio, Tatiana; di Sarra, Alcide; Gómez-Amo, José-Luis; Lucarelli, Franco; Marconi, Miriam; Meloni, Daniela; Monteleone, Francesco; Nava, Silvia; Pace, Giandomenico; Severi, Mirko; Massimiliano Sferlazzo, Damiano; Traversi, Rita; Udisti, Roberto

2017-02-01

Particulate matter with aerodynamic diameters lower than 10 µm, (PM10) aerosol samples were collected during summer 2013 within the framework of the Chemistry and Aerosol Mediterranean Experiment (ChArMEx) at two sites located north (Capo Granitola) and south (Lampedusa Island), respectively, of the main Mediterranean shipping route in the Straight of Sicily. The PM10 samples were collected with 12 h time resolutions at both sites. Selected metals, main anions, cations and elemental and organic carbon were determined. The evolution of soluble V and Ni concentrations (typical markers of heavy fuel oil combustion) was related to meteorology and ship traffic intensity in the Straight of Sicily, using a high-resolution regional model for calculation of back trajectories. Elevated concentration of V and Ni at Capo Granitola and Lampedusa are found to correspond with air masses from the Straight of Sicily and coincidences between trajectories and positions of large ships; the vertical structure of the planetary boundary layer also appears to play a role, with high V values associated with strong inversions and a stable boundary layer. The V concentration was generally lower at Lampedusa than at Capo Granitola V, where it reached a peak value of 40 ng m-3. Concentrations of rare earth elements (REEs), La and Ce in particular, were used to identify possible contributions from refineries, whose emissions are also characterized by elevated V and Ni amounts; refinery emissions are expected to display high La / Ce and La / V ratios due to the use of La in the fluid catalytic converter systems. In general, low La / Ce and La / V ratios were observed in the PM samples. The combination of the analyses based on chemical markers, air mass trajectories and ship routes allows us to unambiguously identify the large role of the ship source in the Straight of Sicily. Based on the sampled aerosols, ratios of the main aerosol species arising from ship emission with respect to V were estimated with the aim of deriving a lower limit for the total ship contribution to PM10. The estimated minimum ship emission contributions to PM10 were 2.0 µg m-3 at Lampedusa and 3.0 µg m-3 at Capo Granitola, corresponding with 11 and 8.6 % of PM10, respectively.

Adult Competency Education Kit. Basic Skills in Speaking, Math, and Reading for Employment. Part Q. ACE Competency Based Job Descriptions: #91--Meat Cutter; #92--Shipping Clerk; #93--Long Haul Truck Driver; #94--Truck Driver--Light.

ERIC Educational Resources Information Center

San Mateo County Office of Education, Redwood City, CA. Career Preparation Centers.

This fourteenth of fifteen sets of Adult Competency Education (ACE) Based Job Descriptions in the ACE kit contains job descriptions for Meat Cutter, Shipping Clerk, Long Haul Truck Driver, and Truck Driver--Light. Each begins with a fact sheet that includes this information: occupational title, D.O.T. code, ACE number, career ladder, D.O.T.…

Ports in a storm.

PubMed

Sharma, Dinesh C

2006-04-01

In many parts of the world, shipping-related emissions have already exceeded or are expected to soon exceed those from land-based sources. Shipping emissions can be reduced substantially by using some of the same technologies being applied to land-based sources, including cleaner engines and fuels, exhaust control methods, and operational modifications. Various ports are testing the feasibility of these mechanisms with varying degrees of success. What is perhaps most greatly needed is expedited creation of better regulations at all levels, from the International Maritime Organization to port city authorities.

Incidence, Etiology and Risk Factors for Travelers Diarrhea during a Hospital Ship-Based Military Humanitarian Mission: Continuing Promise 2011 (Open Access Publishers Version)

DTIC Science & Technology

2016-05-12

RESEARCH ARTICLE Incidence, Etiology and Risk Factors for Travelers ’ Diarrhea during a Hospital Ship- Based Military Humanitarian Mission: Continuing...Development Foundation, Bali, Indonesia ☯ These authors contributed equally to this work. *mark.s.riddle10.mil@mail.mil Abstract Travelers ’ diarrhea (TD) is...the most common ailment affecting travelers , including deployed U.S. military. Continuing Promise 2011 was a 5-month humanitarian assistance/disaster

The development of internet based ship design support system for small and medium sized shipyards

NASA Astrophysics Data System (ADS)

Shin, Sung-Chul; Lee, Soon-Sup; Kang, Dong-Hoon; Lee, Kyung-Ho

2012-03-01

In this paper, a prototype of ship basic planning system is implemented for the small and medium sized shipyards based on the internet technology and concurrent engineering concept. The system is designed from the user requirements. Consequently, standardized development environment and tools are selected. These tools are used for the system development to define and evaluate core application technologies. The system will contribute to increasing competitiveness of small and medium sized shipyards in the 21st century industrial en-vironment.

Convolutional Neural Network Based on Extreme Learning Machine for Maritime Ships Recognition in Infrared Images.

PubMed

Khellal, Atmane; Ma, Hongbin; Fei, Qing

2018-05-09

The success of Deep Learning models, notably convolutional neural networks (CNNs), makes them the favorable solution for object recognition systems in both visible and infrared domains. However, the lack of training data in the case of maritime ships research leads to poor performance due to the problem of overfitting. In addition, the back-propagation algorithm used to train CNN is very slow and requires tuning many hyperparameters. To overcome these weaknesses, we introduce a new approach fully based on Extreme Learning Machine (ELM) to learn useful CNN features and perform a fast and accurate classification, which is suitable for infrared-based recognition systems. The proposed approach combines an ELM based learning algorithm to train CNN for discriminative features extraction and an ELM based ensemble for classification. The experimental results on VAIS dataset, which is the largest dataset of maritime ships, confirm that the proposed approach outperforms the state-of-the-art models in term of generalization performance and training speed. For instance, the proposed model is up to 950 times faster than the traditional back-propagation based training of convolutional neural networks, primarily for low-level features extraction.

Mixed-methods analytic approach for determining potential impacts of vessel noise on sperm whale click behavior.

PubMed

Azzara, Alyson J; von Zharen, Wyndylyn M; Newcomb, Joal J

2013-12-01

The Gulf of Mexico is a center of marine activities from seismic exploration to shipping, drilling, platform installation, lightering, and construction, among others. This analysis explored whether sperm whales respond to the passage of vessels using changes in total number of clicks during vessel passages as a proxy for potential variation in behavior. The data for this analysis were collected in 2001 as part of a larger Littoral Acoustic Demonstration Center project using the Environmental Acoustics Recording System buoys. These buoys were bottom moored, autonomous, and self-recording systems consisting of an omni-directional hydrophone and instrument package. Data from 36 days of continuous acoustic monitoring were recorded at a sampling rate of 11.725 kHz, and produced reliable recordings from 5 Hz to ∼5.8 kHz. Multiple preparatory steps were executed including calibration of an automatic click detector. Results indicate a significant decrease (32%) in the number of clicks detected as a ship approached an area. There were also significantly fewer clicks detected after the vessel passed than before (23%).

A multi-sensor scenario for coastal surveillance

NASA Astrophysics Data System (ADS)

van den Broek, A. C.; van den Broek, S. P.; van den Heuvel, J. C.; Schwering, P. B. W.; van Heijningen, A. W. P.

2007-10-01

Maritime borders and coastal zones are susceptible to threats such as drug trafficking, piracy, undermining economical activities. At TNO Defence, Security and Safety various studies aim at improving situational awareness in a coastal zone. In this study we focus on multi-sensor surveillance of the coastal environment. We present a study on improving classification results for small sea surface targets using an advanced sensor suite and a scenario in which a small boat is approaching the coast. A next generation sensor suite mounted on a tower has been defined consisting of a maritime surveillance and tracking radar system, capable of producing range profiles and ISAR imagery of ships, an advanced infrared camera and a laser range profiler. For this suite we have developed a multi-sensor classification procedure, which is used to evaluate the capabilities for recognizing and identifying non-cooperative ships in coastal waters. We have found that the different sensors give complementary information. Each sensor has its own specific distance range in which it contributes most. A multi-sensor approach reduces the number of misclassifications and reliable classification results are obtained earlier compared to a single sensor approach.

Recent advances in vibro-impact dynamics and collision of ocean vessels

NASA Astrophysics Data System (ADS)

Ibrahim, Raouf A.

2014-11-01

The treatment of ship impacts and collisions takes different approaches depending on the emphasis of each discipline. For example, dynamicists, physicist, and mathematicians are dealing with developing analytical models and mappings of vibro-impact systems. On the other hand, naval architects and ship designers are interested in developing design codes and structural assessments due to slamming loads, liquid sloshing impact loads in liquefied natural gas tanks and ship grounding accidents. The purpose of this review is to highlight the main differences of the two disciplines. It begins with a brief account of the theory of vibro-impact dynamics based on modeling and mapping of systems experiencing discontinuous changes in their state of motion due to collision. The main techniques used in modeling include power-law phenomenological modeling, Hertzian modeling, and non-smooth coordinate transformations originally developed by Zhuravlev and Ivanov. In view of their effectiveness, both Zhuravlev and Ivanov non-smooth coordinate transformations will be described and assessed for the case of ship roll dynamics experiencing impact with rigid barriers. These transformations have the advantage of converting the vibro-impact oscillator into an oscillator without barriers such that the corresponding equation of motion does not contain any impact term. One of the recent results dealing with the coefficient of restitution is that its value monotonically decreases with the impact velocity and not unique but random in nature. Slamming loads and grounding events of ocean waves acting on the bottom of high speed vessels will be assessed with reference to the ship structural damage. It will be noticed that naval architects and marine engineers are treating these problems using different approaches from those used by dynamicists. The problem of sloshing impact in liquefied natural gas cargo and related problems will be assessed based on the numerical and experimental results. It is important for vessel designers to determine the capacity of ships to resist random slamming loads, sloshing loading impact, grounding accidents and ships collisions.

Portable Radiation Package (PRP) Instrument Handbook

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reynolds, R Michael

The Portable Radiation Package (PRP) was developed to provide basic radiation information in locations such as ships at sea where proper exposure is remote and difficult, the platform is in motion, and azimuth alignment is not fixed. Development of the PRP began at Brookhaven National Laboratory (BNL) in the mid-1990s and versions of it were deployed on ships in the U.S. Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) Climate Research Facility’s Nauru-99 project. The PRP was deployed on ships in support of the National Aeronautics and Space Administration (NASA) Sensor Intercomparison for Marine Biological and Interdisciplinary Ocean Studies (SIMBIOS)more » program. Over the years the measurements have remained the same while the post-processing data analysis, especially for the FRSR, has evolved. This document describes the next-generation Portable Radiation Package (PRP2) that was developed for the DOE ARM Facility, under contract no. 9F-31462 from Argonne National Laboratory (ANL). The PRP2 has the same scientific principles that were well validated in prior studies, but has upgraded electronic hardware. The PRP2 approach is completely modular, both in hardware and software. Each sensor input is treated as a separate serial stream into the data collection computer. In this way the operator has complete access to each component of the system for purposes of error checking, calibration, and maintenance. The resulting system is more reliable, easier to install in complex situations, and more amenable to upgrade.« less

LNG systems for natural gas propelled ships

NASA Astrophysics Data System (ADS)

Chorowski, M.; Duda, P.; Polinski, J.; Skrzypacz, J.

2015-12-01

In order to reduce the atmospheric pollution generated by ships, the International Marine Organization has established Emission Controlled Areas. In these areas, nitrogen oxides, sulphur oxides and particulates emission is strongly controlled. From the beginning of 2015, the ECA covers waters 200 nautical miles from the coast of the US and Canada, the US Caribbean Sea area, the Baltic Sea, the North Sea and the English Channel. From the beginning of 2020, strong emission restrictions will also be in force outside the ECA. This requires newly constructed ships to be either equipped with exhaust gas cleaning devices or propelled with emission free fuels. In comparison to low sulphur Marine Diesel and Marine Gas Oil, LNG is a competitive fuel, both from a technical and economical point of view. LNG can be stored in vacuum insulated tanks fulfilling the difficult requirements of marine regulations. LNG must be vaporized and pressurized to the pressure which is compatible with the engine requirements (usually a few bar). The boil-off must be controlled to avoid the occasional gas release to the atmosphere. This paper presents an LNG system designed and commissioned for a Baltic Sea ferry. The specific technical features and exploitation parameters of the system will be presented. The impact of strict marine regulations on the system's thermo-mechanical construction and its performance will be discussed. The review of possible flow-schemes of LNG marine systems will be presented with respect to the system's cost, maintenance, and reliability.

Connecting Land-Based Networks to Ships

DTIC Science & Technology

2013-06-01

multipoint wireless broadband systems, and WiMAX networks were initially deployed for fixed and nomadic (portable) applications. These standards...CAPABILITIES OF SHIP-TO-SHORE COMMUNICATIONS A. US Navy Automated Digital Network System (ADNS) The U.S. Navy’s Automated Digital Network System (ADNS...submit digitally any necessary documents to the terminal operators, contact their logistics providers, access tidal information and receive

4. Credit WCT. Photographic copy of photograph, test Stand 'B' ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. Credit WCT. Photographic copy of photograph, test Stand 'B' set up for shock tube and research on ship-to-ship fueling problems for the U.S. Coast Guard. (JPL negative no. 344-3743-A, October or November 1980) - Jet Propulsion Laboratory Edwards Facility, Test Stand B, Edwards Air Force Base, Boron, Kern County, CA

Shipboard Acoustic Current Profiling during the Coastal Ocean Dynamics Experiment,

DTIC Science & Technology

1985-05-01

average profile based on the bottori depth estimated from the ship’s posit ion. in the CODEU region. an efficient computer routine was developed for... forex ~and and( port ward comnport ent s of V. at conistant z ., the depth Iill ships coordi- nlatv (’S(Chap 2). The data cort- from I -mintIe

VTOL shipboard letdown guidance system analysis

NASA Technical Reports Server (NTRS)

Phatak, A. V.; Karmali, M. S.

1983-01-01

Alternative letdown guidance strategies are examined for landing of a VTOL aircraft onboard a small aviation ship under adverse environmental conditions. Off line computer simulation of shipboard landing task is utilized for assessing the relative merits of the proposed guidance schemes. The touchdown performance of a nominal constant rate of descent (CROD) letdown strategy serves as a benchmark for ranking the performance of the alternative letdown schemes. Analysis of ship motion time histories indicates the existence of an alternating sequence of quiescent and rough motions called lulls and swells. A real time algorithms lull/swell classification based upon ship motion pattern features is developed. The classification algorithm is used to command a go/no go signal to indicate the initiation and termination of an acceptable landing window. Simulation results show that such a go/no go pattern based letdown guidance strategy improves touchdown performance.

NASA's Ship-Aircraft Bio-Optical Research (SABOR)

NASA Image and Video Library

2014-08-25

Sunset Over the Gulf of Maine On July 20, 2013, scientists at sea with NASA's SABOR experiment witnessed a spectacular sunset over the Gulf of Maine. NASA's Ship-Aircraft Bio-Optical Research (SABOR) experiment is a coordinated ship and aircraft observation campaign off the Atlantic coast of the United States, an effort to advance space-based capabilities for monitoring microscopic plants that form the base of the marine food chain. Read more: 1.usa.gov/WWRVzj Credit: NASA/SABOR/Wayne Slade, Sequoia Scientific .NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

NASA's Ship-Aircraft Bio-Optical Research (SABOR)

NASA Image and Video Library

2017-12-08

Instruments Overboard On July 26, 2014, scientists worked past dusk to prepare and deploy the optical instruments and ocean water sensors during NASA's SABOR experiment. NASA's Ship-Aircraft Bio-Optical Research (SABOR) experiment is a coordinated ship and aircraft observation campaign off the Atlantic coast of the United States, an effort to advance space-based capabilities for monitoring microscopic plants that form the base of the marine food chain. Read more: 1.usa.gov/WWRVzj Credit: NASA/SABOR/Wayne Slade, Sequoia Scientific . NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

NASA's Ship-Aircraft Bio-Optical Research (SABOR)

NASA Image and Video Library

2014-08-25

What's in the Water? Robert Foster, of the City College of New York, filters seawater on July 23, 2414, for chlorophyll analysis in a lab on the R/V Endeavor. NASA's Ship-Aircraft Bio-Optical Research (SABOR) experiment is a coordinated ship and aircraft observation campaign off the Atlantic coast of the United States, an effort to advance space-based capabilities for monitoring microscopic plants that form the base of the marine food chain. Read more: 1.usa.gov/WWRVzj Credit: NASA/SABOR/Wayne Slade, Sequoia Scientific..NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

Structure and Interactions of a Dimeric Variant of sHIP, a Novel Virulence Determinant of Streptococcus pyogenes.

PubMed

Diehl, Carl; Wisniewska, Magdalena; Frick, Inga-Maria; Streicher, Werner; Björck, Lars; Malmström, Johan; Wikström, Mats

2016-01-01

Streptococcus pyogenes is one of the most significant bacterial pathogens in the human population mostly causing superficial and uncomplicated infections (pharyngitis and impetigo) but also invasive and life-threatening disease. We have previously identified a virulence determinant, protein sHIP, which is secreted at higher levels by an invasive compared to a non-invasive strain of S. pyogenes. The present work presents a further characterization of the structural and functional properties of this bacterial protein. Biophysical and structural studies have shown that protein sHIP forms stable tetramers both in the crystal and in solution. The tetramers are composed of four helix-loop-helix motifs with the loop regions connecting the helices displaying a high degree of flexibility. Owing to interactions at the tetramer interface, the observed tetramer can be described as a dimer of dimers. We identified three residues at the tetramer interface (Leu84, Leu88, Tyr95), which due to largely non-polar side-chains, could be important determinants for protein oligomerization. Based on these observations, we produced a sHIP variant in which these residues were mutated to alanines. Biophysical experiments clearly indicated that the sHIP mutant appear only as dimers in solution confirming the importance of the interfacial residues for protein oligomerisation. Furthermore, we could show that the sHIP mutant interacts with intact histidine-rich glycoprotein (HRG) and the histidine-rich repeats in HRG, and inhibits their antibacterial activity to the same or even higher extent as compared to the wild type protein sHIP. We determined the crystal structure of the sHIP mutant, which, as a result of the high quality of the data, allowed us to improve the existing structural model of the protein. Finally, by employing NMR spectroscopy in solution, we generated a model for the complex between the sHIP mutant and an HRG-derived heparin-binding peptide, providing further molecular details into the interactions involving protein sHIP.

Estimating the risk of communicable diseases aboard cargo ships.

PubMed

Schlaich, Clara C; Oldenburg, Marcus; Lamshöft, Maike M

2009-01-01

International travel and trade are known to be associated with the risk of spreading communicable diseases across borders. No international surveillance system for infectious diseases on ships exists. Outbreak reports and systematic studies mainly focus on disease activity on cruise ships. The study aims to assess the relevance of communicable disease occurrence on cargo ships. Retrospective analysis of all documented entries to 49 medical log books from seagoing cargo ships under German flag between 2000 and 2008. Incidence rates were calculated per 100 person-years at sea. Case series of acute respiratory illness, influenza-like illness, and infectious gastrointestinal illness affecting more than two persons within 1 successive week were classified as an outbreak. Attack rates were calculated based on number of entries to the medical log book in comparison to the average shipboard population during outbreak periods. During more than 1.5 million person-days of observation, 21% of the visits to the ship's infirmary were due to presumably communicable diseases (45.8 consultations per 100 person-years). As many as 33.9 patients per 100 person-years sought medical attention for acute respiratory symptoms. Of the 68 outbreaks that met predefined criteria, 66 were caused by acute respiratory illness with a subset of 12 outbreaks caused by influenza-like illness. Attack rates ranged between 3 and 10 affected seafarers per ship (12.5&-41.6% of the crew). Two outbreaks of gastrointestinal illness were detected. Respiratory illness is the most common cause of presumably communicable diseases aboard cargo ships and may cause outbreaks of considerable morbidity. Although the validity of the data is limited due to the use of nonprofessional diagnoses, missing or illegible entries, and restriction of the study population to German ships, the results provide guidance to ship owners and to Port Health Authorities to allocate resources and build capacities under International Health Regulations 2005.

C-17 Shipping InSight Mars Spacecraft to Vandenberg Air Force Base

NASA Image and Video Library

2018-02-28

A C-17 cargo aircraft carrying NASA's InSight spacecraft flew from Buckley Air Force Base, Denver, to Vandenberg Air Force Base, California, on February 28, 2018. The spacecraft was being shipped from Lockheed Martin Space, Denver, where InSight was built and tested. Its launch period opens May 5, 2018. InSight, short for Interior Exploration using Seismic Investigations, Geodesy and Heat Transport, is the first mission dedicated to studying the deep interior of Mars. Its findings will advance understanding of the early history of all rocky planets, including Earth. https://photojournal.jpl.nasa.gov/catalog/PIA22251

Ship Detection Using High Resolution Satellite Imagery and Space-Based AIS

NASA Astrophysics Data System (ADS)

Hannevik, Tonje Nanette; Skauen, Andreas N.; Olsen, R. B.

2013-03-01

This paper presents a trial carried out in the Malangen area close to Tromsø city in the north of Norway in September 2010. High resolution Synthetic Aperture Radar (SAR) images from RADARSAT-2 were used to analyse how SAR images and cooperative reporting can be combined. Data from the Automatic Identification System, both land-based and space-based, have been used to identify detected vessels in the SAR images. The paper presents results of ship detection in high resolution RADARSAT-2 Standard Quad-Pol images, and how these results together with land-based and space-based AIS can be used. Some examples of tracking of vessels are also shown.

The Inositol Phosphatase SHIP Controls Salmonella enterica Serovar Typhimurium Infection In Vivo▿

PubMed Central

Bishop, Jennifer L.; Sly, Laura M.; Krystal, Gerald; Finlay, B. Brett

2008-01-01

The SH2 domain-containing inositol 5′-phosphatase, SHIP, negatively regulates various hematopoietic cell functions and is critical for maintaining immune homeostasis. However, whether SHIP plays a role in controlling bacterial infections in vivo remains unknown. Salmonella enterica causes human salmonellosis, a disease that ranges in severity from mild gastroenteritis to severe systemic illness, resulting in significant morbidity and mortality worldwide. The susceptibility of ship+/+and ship−/− mice and bone marrow-derived macrophages to S. enterica serovar Typhimurium infection was compared. ship−/− mice displayed an increased susceptibility to both oral and intraperitoneal serovar Typhimurium infection and had significantly higher bacterial loads in intestinal and systemic sites than ship+/+mice, indicating a role for SHIP in the gut-associated and systemic pathogenesis of serovar Typhimurium in vivo. Cytokine analysis of serum from orally infected mice showed that ship−/− mice produce lower levels of Th1 cytokines than do ship+/+ animals at 2 days postinfection, and in vitro analysis of supernatants taken from infected bone marrow-derived macrophages derived to mimic the in vivo ship−/− alternatively activated (M2) macrophage phenotype correlated with these data. M2 macrophages were the predominant population in vivo in both oral and intraperitoneal infections, since tissue macrophages within the small intestine and peritoneal macrophages from ship−/− mice showed elevated levels of the M2 macrophage markers Ym1 and Arginase 1 compared to ship+/+ cells. Based on these data, we propose that M2 macrophage skewing in ship−/− mice contributes to ineffective clearance of Salmonella in vivo. PMID:18426884

Automated generation of weld path trajectories.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sizemore, John M.; Hinman-Sweeney, Elaine Marie; Ames, Arlo Leroy

2003-06-01

AUTOmated GENeration of Control Programs for Robotic Welding of Ship Structure (AUTOGEN) is software that automates the planning and compiling of control programs for robotic welding of ship structure. The software works by evaluating computer representations of the ship design and the manufacturing plan. Based on this evaluation, AUTOGEN internally identifies and appropriately characterizes each weld. Then it constructs the robot motions necessary to accomplish the welds and determines for each the correct assignment of process control values. AUTOGEN generates these robot control programs completely without manual intervention or edits except to correct wrong or missing input data. Most shipmore » structure assemblies are unique or at best manufactured only a few times. Accordingly, the high cost inherent in all previous methods of preparing complex control programs has made robot welding of ship structures economically unattractive to the U.S. shipbuilding industry. AUTOGEN eliminates the cost of creating robot control programs. With programming costs eliminated, capitalization of robots to weld ship structures becomes economically viable. Robot welding of ship structures will result in reduced ship costs, uniform product quality, and enhanced worker safety. Sandia National Laboratories and Northrop Grumman Ship Systems worked with the National Shipbuilding Research Program to develop a means of automated path and process generation for robotic welding. This effort resulted in the AUTOGEN program, which has successfully demonstrated automated path generation and robot control. Although the current implementation of AUTOGEN is optimized for welding applications, the path and process planning capability has applicability to a number of industrial applications, including painting, riveting, and adhesive delivery.« less

Recommendations for assessing water quality and safety on board merchant ships.

PubMed

Grappasonni, Iolanda; Cocchioni, Mario; Degli Angioli, Rolando; Saturnino, Andrea; Sibilio, Fabio; Scuri, Stefania; Amenta, Francesco

2013-01-01

Health and diseases on board ships may depend on water. Interventions to improve the quality of water may bring to significant benefits to health and water stores/supply and should be controlledto protect health. This paper has reviewed the main regulations for the control of water safety and qualityon board ships and presents some practical recommendations for keeping water healthy and safe in passenger and cargo merchant ships. The main international regulations and guidelines on the topic were analysed. Guidelines forWater Quality on Board Merchant Ships Including Passenger Vessels of Health Protection Agency, World Health Organisation (WHO) Guide to Ship Sanitation, WHO Guidelines for Drinking Water Quality, WHO Water Safety Plan and the United States Center for Disease Control and Prevention Vessel Sanitation Program were examined. Recommendations for passenger and, if available, for cargo ships were collected and compared. Recommended questionnaire: A questionnaire summarising the main information to collect for assessingthe enough quality of water for the purposes it should be used on board is proposed. The need of havinga crew member with water assessment duties on board, trained for performing these activities properlyis discussed. Water quality on board ships should be monitored routinely. Monitoring should be directedto chemical and microbiological parameters for identifying possible contamination sources, using specifickits by a designed crew member. More detailed periodic assessments should be under the responsibility ofspecialised personnel/laboratories and should be based on sample collection from all tanks and sites of waterdistribution. It is important to select a properly trained crew member on board for monitoring water quality.

Work-related homicides among seafarers and fishermen.

PubMed

Roberts, Stephen E

2004-01-01

To analyse work related homicides among various defined populations of seafarers and fishermen during the period 1976-2002, to compare homicide rates with other occupations and general populations, and to discuss implications for maritime health and safety. A longitudinal study of work related homicides, based on official mortality files, with an aggregated population of almost two million seafarer-and fishermen-years at risk. Of 46 work related homicides, 44 occurred among seafarers, and two among fishermen. Homicide rates were 1.5 per 100,000 worker-years among seafarers in British merchant shipping (1976-2002), 2.9 per 100,000 among British seafarers employed in non British shipping (1986-95), 3.7 in Singapore shipping (1984-95) and in Hong Kong shipping (1981-95), and 0.4 among fishermen in British fishing (1976-2002). The homicide rate in British shipping increased from 2.7 per 100,000 seafarer-years in 1961-65 to 4.4 per 100,000 in 1971-75, but has declined to 0.0 in 1996-2002. Although work related homicides were generally quite rare occurrences, among British seafarers and fishermen, they were largely caused by attacks from assailants, other than colleagues, that occurred ashore. The decline in the homicide rate in British shipping since the 1970s has coincided with the reduction in deep-sea ships trading to high risk countries for homicide. Among Asian seafarers, most homicides resulted from disputes among colleagues that mainly occurred on board ships. Prevention should include alertness to potential risks when spending off-duty time ashore in locations with high homicide rates, and conflict resolution for disputes among seafarers.

Sentinel-1A - Launching the first satellite and launching the operational Copernicus programme

NASA Astrophysics Data System (ADS)

Aschbacher, Josef; Milagro Perez, Maria Pilar

2014-05-01

The first Copernicus satellite, Sentinel-1A, is prepared for launch in April 2014. It will provide continuous, systematic and highly reliable radar images of the Earth. Sentinel-1B will follow around 18 months later to increase observation frequency and establish an operational system. Sentinel-1 is designed to work in a pre-programmed conflict-free operation mode ensuring the reliability required by operational services and creating a consistent long-term data archive for applications based on long time series. This mission will ensure the continuation and improvement of SAR operational services and applications addressing primarily medium- to high-resolution applications through a main mode of operation that features both a wide swath (250 km) and high geometric (5 × 20 m) and radiometric resolution, allowing imaging of global landmasses, coastal zones, sea ice, polar areas, and shipping routes at high resolution. The Sentinel-1 main operational mode (Interferometric Wide Swath) will allow to have a complete coverage of the Earth in 6 days in the operational configuration when the two Sentinel-1 spacecraft will be in orbit simultaneously. High priority areas like Europe, Canada and some shipping routes will be covered almost daily. This high global observation frequency is unprecedented and cannot be reached with any other current radar mission. Envisat, for example, which was the 'workhorse' in this domain up to April 2012, reached global coverage every 35 days. Sentinel-1 data products will be made available systematically and free of charge to all users including institutional users, the general public, scientific and commercial users. The transition of the Copernicus programme from the development to operational phase will take place at about the same time when the first Sentinel-1 satellite will be launched. During the operational phase, funding of the programme will come from the European Union Multiannual Financial Framework (MFF) for the years 2014-2020. The EU Copernicus Regulation, laying down the legal basis for the EU operational Copernicus programme, is currently in its final phase of approval by the European Parliament and Council. Based on this, the future EU-ESA Copernicus Agreement will define the modalities for the cooperation between ESA and the EU for the period 2014-2020 and will regulate the budget implementation tasks entrusted to ESA by the EU for the accomplishment of the space segment and the programme operations phase. The agreement, once signed, will pave the way for important procurements over the next seven years in the Earth observation domain.

KSC-02pd1538

NASA Image and Video Library

2002-10-15

KENNEDY SPACE CENTER, FLA. -- Workers on the deck of the Liberty Star, one of NASA's solid rocket booster retrieval ships, as well as divers in the water, help lower sonar mapping equipment alongside the ship. The equipment will be attached to the ship's hull for an eight-day expedition surveying deep-water coral reefs on the Oculina Banks off eastern Florida. NASA joins the National Oceanic and Atmospheric Administration (NOAA) and other ocean scientists for the sophisticated mapping system that will provide the first high-resolution, three-dimensional map of the Oculina Banks. The survey results are expected to guide another expedition in Spring 2003, using NASA's ship, when the reef fish spawn. Also used will be NASA's underwater robot and an acoustic hydrophone system for listening to fish and vessel noise. Dive sites will be chosen based on the new charts.

KSC-02pd1536

NASA Image and Video Library

2002-10-15

KENNEDY SPACE CENTER, FLA. -- Workers on the deck of the Liberty Star, one of NASA's solid rocket booster retrieval ships, oversee the lifting of sonar mapping equipment from the deck toward the side of the ship. The equipment will be attached to the ship's hull for an eight-day expedition surveying deep-water coral reefs on the Oculina Banks off eastern Florida. NASA joins the National Oceanic and Atmospheric Administration (NOAA) and other ocean scientists for the sophisticated mapping system that will provide the first high-resolution, three-dimensional map of the Oculina Banks. The survey results are expected to guide another expedition in Spring 2003, using NASA's ship, when the reef fish spawn. Also used will be NASA's underwater robot and an acoustic hydrophone system for listening to fish and vessel noise. Dive sites will be chosen based on the new charts.

KSC-06pd2648

NASA Image and Video Library

2006-12-01

KENNEDY SPACE CENTER, FLA. -- Radar operator Scott Peabody tests the X-band radar array installed on the solid rocket booster retrieval ship Liberty before launch of Space Shuttle Discovery. It is one of two Weibel Continuous Pulse Doppler X-band radars located on each of the two SRB retrieval ships. This one will be located downrange of the launch site. It is one of two Weibel Continuous Pulse Doppler X-band radars located on each of the two SRB retrieval ships. This one will be located downrange of the launch site. Working with the land-based C-band radar, the X-band radars provide velocity and differential shuttle/debris motion information during launch. The radar data will be sent from the ships via satellite link and analyzed at the C-band radar site located on north Kennedy Space Center. Photo credit: NASA/George Shelton

KSC-06pd2647

NASA Image and Video Library

2006-12-01

KENNEDY SPACE CENTER, FLA. -- Radar operator Scott Peabody tests the X-band radar array installed on the solid rocket booster retrieval ship Liberty before launch of Space Shuttle Discovery. It is one of two Weibel Continuous Pulse Doppler X-band radars located on each of the two SRB retrieval ships. This one will be located downrange of the launch site. It is one of two Weibel Continuous Pulse Doppler X-band radars located on each of the two SRB retrieval ships. This one will be located downrange of the launch site. Working with the land-based C-band radar, the X-band radars provide velocity and differential shuttle/debris motion information during launch. The radar data will be sent from the ships via satellite link and analyzed at the C-band radar site located on north Kennedy Space Center. Photo credit: NASA/George Shelton

Passive bottom reflection-loss estimation using ship noise and a vertical line array.

PubMed

Muzi, Lanfranco; Siderius, Martin; Verlinden, Christopher M

2017-06-01

An existing technique for passive bottom-loss estimation from natural marine surface noise (generated by waves and wind) is adapted to use noise generated by ships. The original approach-based on beamforming of the noise field recorded by a vertical line array of hydrophones-is retained; however, additional processing is needed in order for the field generated by a passing ship to show features that are similar to those of the natural surface-noise field. A necessary requisite is that the ship position, relative to the array, varies over as wide a range of steering angles as possible, ideally passing directly over the array to ensure coverage of the steepest angles. The methodology is illustrated through simulation and applied to data from a field experiment conducted offshore of San Diego, CA in 2009.

Design, fabricate, and provide engineering support for radiosotope thermoelectric generators for NASA'S CRHF and CASSINI missions

NASA Astrophysics Data System (ADS)

The technical progress achieved during the period 11 January through 31 March 1991 on Contract DE-AC03-91SF18852.000 Radioisotope Thermoelectric Generators and ancillary activities is described. The system contract consists of the following tasks: (1) Spacecraft Integration and Liaison; (2) Engineering Support; (3) Safety; (4) Qualify Unicouple Fabrication; (5) ETG Fabrication, Assembly and Test; (6) GSE; (7) RTG Shipping and Launch Support; (8) Designs, Reviews, and Mission Applications; (9) Project Management, Quality Assurance and Reliability; and (10) CAGO Acquisition (Capital Funds). The progress achieved is broken down into these tasks.

GPHS-RTGs in support of the Cassini RTG Program

NASA Astrophysics Data System (ADS)

1995-04-01

The technical progress achieved during the period 26 Sep. 1994 - 2 Apr. 1995 on Contract DE-AC03-91SF-18852 Radioisotope Thermoelectric Generators and Ancillary Activities is described herein. Monthly technical activity for the period 27 Feb. - 2 Apr. 1995 is included in this progress report. The report addresses tasks, including: spacecraft integration and liaison; engineering support; safety; qualified unicouple production; ETG fabrication, assembly, and test; ground support equipment; RTG shipping and launch support; designs, reviews, and mission applications; project management, quality assurance, reliability, contract changes, CAGO acquisition (operating funds), and CAGO maintenance and repair; and CAGO acquisition (capital funds).

Data-driven battery product development: Turn battery performance into a competitive advantage.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sholklapper, Tal

Poor battery performance is a primary source of user dissatisfaction across a broad range of applications, and is a key bottleneck hindering the growth of mobile technology, wearables, electric vehicles, and grid energy storage. Engineering battery systems is difficult, requiring extensive testing for vendor selection, BMS programming, and application-specific lifetime testing. This work also generates huge quantities of data. This presentation will explain how to leverage this data to help ship quality products faster using fewer resources while ensuring safety and reliability in the field, ultimately turning battery performance into a competitive advantage.

Characteristics of PM2.5 from ship emissions and their impacts on the ambient air: A case study in Yangshan Harbor, Shanghai.

PubMed

Mamoudou, Issoufou; Zhang, Fan; Chen, Qi; Wang, Panpan; Chen, Yingjun

2018-05-30

The rapid development of ports in China over the last two decades has had inevitable consequences on the ambient air quality in coastal areas and harbors. For mitigation strategies and monitoring aims, the contributions of ship emissions should be identified, especially in these specific areas. Therefore, in this study, fine particulate matters (PM 2.5 ) samples were collected at Yangshan Harbor in 2016 to characterize ship emissions and estimate their impacts on the ambient air. The results showed that the average annual PM 2.5 concentration was 44.02 μg/m 3 at Yangshan Harbor. The mean seasonal PM 2.5 concentrations reached a maximum in the spring (60.28 μg/m 3 ) and a minimum in the summer (28.04 μg/m 3 ). Two methods were used in this study to estimate the contributions of ship emissions to the ambient air. When a V-based method was used, the primary estimated daily contributions of ship emissions to the ambient air at Yangshan Harbor ranged from 0.02 to 0.73 μg/m 3 with an annual average of 0.10 μg/m 3 . When a PMF-based method was used, the contributions ranged from 0.02 to 9.15 μg/m 3 with an annual average of 1.02 μg/m 3 . In fact, there was a significant underestimation of the true influences of ship emissions when only the primary contribution was considered. In accordance with this evidence, there was a main average underestimation of 1.84 μg/m 3 . Copyright © 2018 Elsevier B.V. All rights reserved.

Development of software for handling ship's pharmacy.

PubMed

Nittari, Giulio; Peretti, Alessandro; Sibilio, Fabio; Ioannidis, Nicholas; Amenta, Francesco

2016-01-01

Ships are required to carry a given amount of medicinal products and medications depending on the flag and the type of vessel. These medicines are stored in the so called ship's "medicine chest" or more properly - a ship pharmacy. Owing to the progress of medical sciences and to the increase in the mean age of seafarers employed on board ships, the number of pharmaceutical products and medical devices required by regulations to be carried on board ships is increasing. This may make handling of the ship's medicine chest a problem primarily on large ships sailing on intercontinental routes due to the difficulty in identifying the correspondence between medicines obtained abroad with those available at the national market. To minimise these problems a tool named Pharmacy Ship (acronym: PARSI) has been developed. The application PARSI is based on a database containing the information about medicines and medical devices required by different countries regulations. In the first application the system was standardised to comply with the Italian regulations issued on the 1st October, 2015 which entered into force on the 18 January 2016. Thanks to PARSI it was possible to standardize the inventory procedures, facilitate the work of maritime health authorities and make it easier for the crew, not professional in the field, to handle the 'medicine chest' correctly by automating the procedures for medicines management. As far as we know there are no other similar tools available at the moment. The application of the software, as well as the automation of different activities, currently carried out manually, will help manage (qualitatively and quantitatively) the ship's pharmacy. The system developed in this study has proved to be an effective tool which serves to guarantee the compliance of the ship pharmacy with regulations of the flag state in terms of medicinal products and medications. Sharing the system with the Telemedical Maritime Assistance Service may result in avoiding mistakes in drug administration. Last but not least the availability of PARSI could help reduce/ avoid problems with maritime health authorities in case any of the required medicinal products are missing.

A new fully automated FTIR system for total column measurements of greenhouse gases

NASA Astrophysics Data System (ADS)

Geibel, M. C.; Gerbig, C.; Feist, D. G.

2010-10-01

This article introduces a new fully automated FTIR system that is part of the Total Carbon Column Observing Network (TCCON). It will provide continuous ground-based measurements of column-averaged volume mixing ratio for CO2, CH4 and several other greenhouse gases in the tropics. Housed in a 20-foot shipping container it was developed as a transportable system that could be deployed almost anywhere in the world. We describe the automation concept which relies on three autonomous subsystems and their interaction. Crucial components like a sturdy and reliable solar tracker dome are described in detail. The automation software employs a new approach relying on multiple processes, database logging and web-based remote control. First results of total column measurements at Jena, Germany show that the instrument works well and can provide parts of the diurnal as well as seasonal cycle for CO2. Instrument line shape measurements with an HCl cell suggest that the instrument stays well-aligned over several months. After a short test campaign for side by side intercomaprison with an existing TCCON instrument in Australia, the system will be transported to its final destination Ascension Island.

Vessel Classification in Cosmo-Skymed SAR Data Using Hierarchical Feature Selection

NASA Astrophysics Data System (ADS)

Makedonas, A.; Theoharatos, C.; Tsagaris, V.; Anastasopoulos, V.; Costicoglou, S.

2015-04-01

SAR based ship detection and classification are important elements of maritime monitoring applications. Recently, high-resolution SAR data have opened new possibilities to researchers for achieving improved classification results. In this work, a hierarchical vessel classification procedure is presented based on a robust feature extraction and selection scheme that utilizes scale, shape and texture features in a hierarchical way. Initially, different types of feature extraction algorithms are implemented in order to form the utilized feature pool, able to represent the structure, material, orientation and other vessel type characteristics. A two-stage hierarchical feature selection algorithm is utilized next in order to be able to discriminate effectively civilian vessels into three distinct types, in COSMO-SkyMed SAR images: cargos, small ships and tankers. In our analysis, scale and shape features are utilized in order to discriminate smaller types of vessels present in the available SAR data, or shape specific vessels. Then, the most informative texture and intensity features are incorporated in order to be able to better distinguish the civilian types with high accuracy. A feature selection procedure that utilizes heuristic measures based on features' statistical characteristics, followed by an exhaustive research with feature sets formed by the most qualified features is carried out, in order to discriminate the most appropriate combination of features for the final classification. In our analysis, five COSMO-SkyMed SAR data with 2.2m x 2.2m resolution were used to analyse the detailed characteristics of these types of ships. A total of 111 ships with available AIS data were used in the classification process. The experimental results show that this method has good performance in ship classification, with an overall accuracy reaching 83%. Further investigation of additional features and proper feature selection is currently in progress.

Seven-Year SSM/I-Derived Global Ocean Surface Turbulent Fluxes

NASA Technical Reports Server (NTRS)

Chou, Shu-Hsien; Shie, Chung-Lin; Atlas, Robert M.; Ardizzone, Joe

2000-01-01

A 7.5-year (July 1987-December 1994) dataset of daily surface specific humidity and turbulent fluxes (momentum, latent heat, and sensible heat) over global oceans has been retrieved from the Special Sensor Microwave/Imager (SSM/I) data and other data. It has a spatial resolution of 2.0 deg.x 2.5 deg. latitude-longitude. The retrieved surface specific humidity is generally accurate over global oceans as validated against the collocated radiosonde observations. The retrieved daily wind stresses and latent heat fluxes show useful accuracy as verified by those measured by the RV Moana Wave and IMET buoy in the western equatorial Pacific. The derived turbulent fluxes and input variables are also found to agree generally with the global distributions of annual-and seasonal-means of those based on 4-year (1990-93) comprehensive ocean-atmosphere data set (COADS) with adjustment in wind speeds and other climatological studies. The COADS has collected the most complete surface marine observations, mainly from merchant ships. However, ship measurements generally have poor accuracy, and variable spatial coverages. Significant differences between the retrieved and COADS-based are found in some areas of the tropical and southern extratropical oceans, reflecting the paucity of ship observations outside the northern extratropical oceans. Averaged over the global oceans, the retrieved wind stress is smaller but the latent heat flux is larger than those based on COADS. The former is suggested to be mainly due to overestimation of the adjusted ship-estimated wind speeds (depending on sea states), while the latter is suggested to be mainly due to overestimation of ship-measured dew point temperatures. The study suggests that the SSM/I-derived turbulent fluxes can be used for climate studies and coupled model validations.

Robustness and cognition in stabilization problem of dynamical systems based on asymptotic methods

NASA Astrophysics Data System (ADS)

Dubovik, S. A.; Kabanov, A. A.

2017-01-01

The problem of synthesis of stabilizing systems based on principles of cognitive (logical-dynamic) control for mobile objects used under uncertain conditions is considered. This direction in control theory is based on the principles of guaranteeing robust synthesis focused on worst-case scenarios of the controlled process. The guaranteeing approach is able to provide functioning of the system with the required quality and reliability only at sufficiently low disturbances and in the absence of large deviations from some regular features of the controlled process. The main tool for the analysis of large deviations and prediction of critical states here is the action functional. After the forecast is built, the choice of anti-crisis control is the supervisory control problem that optimizes the control system in a normal mode and prevents escape of the controlled process in critical states. An essential aspect of the approach presented here is the presence of a two-level (logical-dynamic) control: the input data are used not only for generating of synthesized feedback (local robust synthesis) in advance (off-line), but also to make decisions about the current (on-line) quality of stabilization in the global sense. An example of using the presented approach for the problem of development of the ship tilting prediction system is considered.

A Damping Grid Strapdown Inertial Navigation System Based on a Kalman Filter for Ships in Polar Regions.

PubMed

Huang, Weiquan; Fang, Tao; Luo, Li; Zhao, Lin; Che, Fengzhu

2017-07-03

The grid strapdown inertial navigation system (SINS) used in polar navigation also includes three kinds of periodic oscillation errors as common SINS are based on a geographic coordinate system. Aiming ships which have the external information to conduct a system reset regularly, suppressing the Schuler periodic oscillation is an effective way to enhance navigation accuracy. The Kalman filter based on the grid SINS error model which applies to the ship is established in this paper. The errors of grid-level attitude angles can be accurately estimated when the external velocity contains constant error, and then correcting the errors of the grid-level attitude angles through feedback correction can effectively dampen the Schuler periodic oscillation. The simulation results show that with the aid of external reference velocity, the proposed external level damping algorithm based on the Kalman filter can suppress the Schuler periodic oscillation effectively. Compared with the traditional external level damping algorithm based on the damping network, the algorithm proposed in this paper can reduce the overshoot errors when the state of grid SINS is switched from the non-damping state to the damping state, and this effectively improves the navigation accuracy of the system.

Enhancing Arctic Surveillance With Space-Based Radars

DTIC Science & Technology

2013-06-01

shipping, hydrocarbon extraction, fishing, and tourism activities (to name but just a few) are increasing in frequency, duration, and intensity and...maritime activities in the Arctic Circle ranging from relatively benign tourism ventures to adversary naval combatant maneuvers, the United States...activities there (U.S. Northern Command Posture Statement, 2011). Without awareness of human activities such as shipping, tourism , military operations

15 CFR 750.11 - Shipping tolerances.

Code of Federal Regulations, 2013 CFR

2013-01-01

... based on the “Unit” specified for the item you want to export in the applicable ECCN on the CCL (see... in the ECCN applicable to your item reads “ $ value” or “in $ value”, there is no shipping tolerance... “Number”. If the “Unit” paragraph in the ECCN applicable to your item reads “Number” or “in Number”, there...

15 CFR 750.11 - Shipping tolerances.

Code of Federal Regulations, 2011 CFR

2011-01-01

... based on the “Unit” specified for the item you want to export in the applicable ECCN on the CCL (see... in the ECCN applicable to your item reads “ $ value” or “in $ value”, there is no shipping tolerance... “Number”. If the “Unit” paragraph in the ECCN applicable to your item reads “Number” or “in Number”, there...

15 CFR 750.11 - Shipping tolerances.

Code of Federal Regulations, 2012 CFR

2012-01-01

... based on the “Unit” specified for the item you want to export in the applicable ECCN on the CCL (see... in the ECCN applicable to your item reads “ $ value” or “in $ value”, there is no shipping tolerance... “Number”. If the “Unit” paragraph in the ECCN applicable to your item reads “Number” or “in Number”, there...

15 CFR 750.11 - Shipping tolerances.

Code of Federal Regulations, 2010 CFR

2010-01-01

... based on the “Unit” specified for the item you want to export in the applicable ECCN on the CCL (see... in the ECCN applicable to your item reads “ $ value” or “in $ value”, there is no shipping tolerance... “Number”. If the “Unit” paragraph in the ECCN applicable to your item reads “Number” or “in Number”, there...

Enhancing Maritime Education and Training: Measuring a Ship Navigator's Stress Based on Salivary Amylase Activity

ERIC Educational Resources Information Center

Murai, Koji; Wakida, Shin-Ichi; Miyado, Takashi; Fukushi, Keiichi; Hayashi, Yuji; Stone, Laurie C.

2009-01-01

Purpose: The purpose of this paper is to propose that the measurement of salivary amylase activity is an effective index to evaluate the stress of a ship navigator for safe navigation training and education. Design/methodology/approach: Evaluation comes from the simulator and actual on-board experiments. The subjects are real captains who have…

Transfer Learning with Convolutional Neural Networks for SAR Ship Recognition

NASA Astrophysics Data System (ADS)

Zhang, Di; Liu, Jia; Heng, Wang; Ren, Kaijun; Song, Junqiang

2018-03-01

Ship recognition is the backbone of marine surveillance systems. Recent deep learning methods, e.g. Convolutional Neural Networks (CNNs), have shown high performance for optical images. Learning CNNs, however, requires a number of annotated samples to estimate numerous model parameters, which prevents its application to Synthetic Aperture Radar (SAR) images due to the limited annotated training samples. Transfer learning has been a promising technique for applications with limited data. To this end, a novel SAR ship recognition method based on CNNs with transfer learning has been developed. In this work, we firstly start with a CNNs model that has been trained in advance on Moving and Stationary Target Acquisition and Recognition (MSTAR) database. Next, based on the knowledge gained from this image recognition task, we fine-tune the CNNs on a new task to recognize three types of ships in the OpenSARShip database. The experimental results show that our proposed approach can obviously increase the recognition rate comparing with the result of merely applying CNNs. In addition, compared to existing methods, the proposed method proves to be very competitive and can learn discriminative features directly from training data instead of requiring pre-specification or pre-selection manually.

Ship electric propulsion simulator based on networking technology

NASA Astrophysics Data System (ADS)

Zheng, Huayao; Huang, Xuewu; Chen, Jutao; Lu, Binquan

2006-11-01

According the new ship building tense, a novel electric propulsion simulator (EPS) had been developed in Marine Simulation Center of SMU. The architecture, software function and FCS network technology of EPS and integrated power system (IPS) were described. In allusion to the POD propeller in ship, a special physical model was built. The POD power was supplied from the simulative 6.6 kV Medium Voltage Main Switchboard, its control could be realized in local or remote mode. Through LAN, the simulated feature information of EPS will pass to the physical POD model, which would reflect the real thruster working status in different sea conditions. The software includes vessel-propeller math module, thruster control system, distribution and emergency integrated management, double closed loop control system, vessel static water resistance and dynamic software; instructor main control software. The monitor and control system is realized by real time data collection system and CAN bus technology. During the construction, most devices such as monitor panels and intelligent meters, are developed in lab which were based on embedded microcomputer system with CAN interface to link the network. They had also successfully used in practice and would be suitable for the future demands of digitalization ship.

The impact of shipping emissions on air pollution in the greater North Sea region - Part 1: Current emissions and concentrations

NASA Astrophysics Data System (ADS)

Aulinger, A.; Matthias, V.; Zeretzke, M.; Bieser, J.; Quante, M.; Backes, A.

2016-01-01

The North Sea is one of the areas with the highest ship traffic densities worldwide. At any time, about 3000 ships are sailing its waterways. Previous scientific publications have shown that ships contribute significantly to atmospheric concentrations of NOx, particulate matter and ozone. Especially in the case of particulate matter and ozone, this influence can even be seen in regions far away from the main shipping routes. In order to quantify the effects of North Sea shipping on air quality in its bordering states, it is essential to determine the emissions from shipping as accurately as possible. Within Interreg IVb project Clean North Sea Shipping (CNSS), a bottom-up approach was developed and used to thoroughly compile such an emission inventory for 2011 that served as the base year for the current emission situation. The innovative aspect of this approach was to use load-dependent functions to calculate emissions from the ships' current activities instead of averaged emission factors for the entire range of the engine loads. These functions were applied to ship activities that were derived from hourly records of Automatic Identification System signals together with a database containing the engine characteristics of the vessels that traveled the North Sea in 2011. The emission model yielded ship emissions among others of NOx and SO2 at high temporal and spatial resolution that were subsequently used in a chemistry transport model in order to simulate the impact of the emissions on pollutant concentration levels. The total emissions of nitrogen reached 540 Gg and those of sulfur oxides 123 Gg within the North Sea - including the adjacent western part of the Baltic Sea until 5° W. This was about twice as much of those of a medium-sized industrialized European state like the Netherlands. The relative contribution of ships to, for example, NO2 concentration levels ashore close to the sea can reach up to 25 % in summer and 15 % in winter. Some hundred kilometers away from the sea, the contribution was about 6 % in summer and 4 % in winter. The relative contribution of the secondary pollutant NO3- was found to reach 20 % in summer and 6 % in winter even far from the shore.

Ship noise extends to frequencies used for echolocation by endangered killer whales.

PubMed

Veirs, Scott; Veirs, Val; Wood, Jason D

2016-01-01

Combining calibrated hydrophone measurements with vessel location data from the Automatic Identification System, we estimate underwater sound pressure levels for 1,582 unique ships that transited the core critical habitat of the endangered Southern Resident killer whales during 28 months between March, 2011, and October, 2013. Median received spectrum levels of noise from 2,809 isolated transits are elevated relative to median background levels not only at low frequencies (20-30 dB re 1 µPa(2)/Hz from 100 to 1,000 Hz), but also at high frequencies (5-13 dB from 10,000 to 96,000 Hz). Thus, noise received from ships at ranges less than 3 km extends to frequencies used by odontocetes. Broadband received levels (11.5-40,000 Hz) near the shoreline in Haro Strait (WA, USA) for the entire ship population were 110 ± 7 dB re 1 µPa on average. Assuming near-spherical spreading based on a transmission loss experiment we compute mean broadband source levels for the ship population of 173 ± 7 dB re 1 µPa 1 m without accounting for frequency-dependent absorption. Mean ship speed was 7.3 ± 2.0 m/s (14.1 ± 3.9 knots). Most ship classes show a linear relationship between source level and speed with a slope near +2 dB per m/s (+1 dB/knot). Spectrum, 1/12-octave, and 1/3-octave source levels for the whole population have median values that are comparable to previous measurements and models at most frequencies, but for select studies may be relatively low below 200 Hz and high above 20,000 Hz. Median source spectrum levels peak near 50 Hz for all 12 ship classes, have a maximum of 159 dB re 1 µPa(2)/Hz @ 1 m for container ships, and vary between classes. Below 200 Hz, the class-specific median spectrum levels bifurcate with large commercial ships grouping as higher power noise sources. Within all ship classes spectrum levels vary more at low frequencies than at high frequencies, and the degree of variability is almost halved for classes that have smaller speed standard deviations. This is the first study to present source spectra for populations of different ship classes operating in coastal habitats, including at higher frequencies used by killer whales for both communication and echolocation.

Automated intelligent video surveillance system for ships

NASA Astrophysics Data System (ADS)

Wei, Hai; Nguyen, Hieu; Ramu, Prakash; Raju, Chaitanya; Liu, Xiaoqing; Yadegar, Jacob

2009-05-01

To protect naval and commercial ships from attack by terrorists and pirates, it is important to have automatic surveillance systems able to detect, identify, track and alert the crew on small watercrafts that might pursue malicious intentions, while ruling out non-threat entities. Radar systems have limitations on the minimum detectable range and lack high-level classification power. In this paper, we present an innovative Automated Intelligent Video Surveillance System for Ships (AIVS3) as a vision-based solution for ship security. Capitalizing on advanced computer vision algorithms and practical machine learning methodologies, the developed AIVS3 is not only capable of efficiently and robustly detecting, classifying, and tracking various maritime targets, but also able to fuse heterogeneous target information to interpret scene activities, associate targets with levels of threat, and issue the corresponding alerts/recommendations to the man-in- the-loop (MITL). AIVS3 has been tested in various maritime scenarios and shown accurate and effective threat detection performance. By reducing the reliance on human eyes to monitor cluttered scenes, AIVS3 will save the manpower while increasing the accuracy in detection and identification of asymmetric attacks for ship protection.

Human occupancy detection

NASA Astrophysics Data System (ADS)

Brown, David A.

1994-10-01

In the area of security and surveillance technologies, the problem of the arrival in Canada of illegal and undesirable ship and truck cargo loads is steadily increasing. As the volumes of cargo arrivals increase so do the Immigration and Customs problems related to the determination of the validity of those cargo contents. Of special concern to Immigration Control Authorities around the world is the emerging and increasing trend of illegal smuggling of human beings hidden inside of shipping containers. Beginning in 1992, Immigration Control Authorities in Canada observed an escalation of alien people smuggling through the use of cargo shipping containers arriving in the Port of Montreal. This paper will present to the audience the recently completed Immigration Canada Human Occupancy Detection project by explaining the design, development and testing of human occupancy detectors. The devices are designed to electronically detect the presence of persons hiding inside of shipping containers, without the requirement of opening the container doors. The human occupancy detection concepts are based upon the presence of carbon dioxide or other human waste characteristics commonly found inside of shipping containers.

Near Real-Time Automatic Marine Vessel Detection on Optical Satellite Images

NASA Astrophysics Data System (ADS)

Máttyus, G.

2013-05-01

Vessel monitoring and surveillance is important for maritime safety and security, environment protection and border control. Ship monitoring systems based on Synthetic-aperture Radar (SAR) satellite images are operational. On SAR images the ships made of metal with sharp edges appear as bright dots and edges, therefore they can be well distinguished from the water. Since the radar is independent from the sun light and can acquire images also by cloudy weather and rain, it provides a reliable service. Vessel detection from spaceborne optical images (VDSOI) can extend the SAR based systems by providing more frequent revisit times and overcoming some drawbacks of the SAR images (e.g. lower spatial resolution, difficult human interpretation). Optical satellite images (OSI) can have a higher spatial resolution thus enabling the detection of smaller vessels and enhancing the vessel type classification. The human interpretation of an optical image is also easier than as of SAR image. In this paper I present a rapid automatic vessel detection method which uses pattern recognition methods, originally developed in the computer vision field. In the first step I train a binary classifier from image samples of vessels and background. The classifier uses simple features which can be calculated very fast. For the detection the classifier is slided along the image in various directions and scales. The detector has a cascade structure which rejects most of the background in the early stages which leads to faster execution. The detections are grouped together to avoid multiple detections. Finally the position, size(i.e. length and width) and heading of the vessels is extracted from the contours of the vessel. The presented method is parallelized, thus it runs fast (in minutes for 16000 × 16000 pixels image) on a multicore computer, enabling near real-time applications, e.g. one hour from image acquisition to end user.

Numerical study of a permanent magnet linear generator for ship motion energy conversion

NASA Astrophysics Data System (ADS)

Mahmuddin, Faisal; Gunadin, Indar Chaerah; Akhir, Anshar Yaumil

2017-02-01

In order to harvest kinetic energy of a ship moving in waves, a permanent magnet linear generator is designed and simulated in the present study. For the sake of simplicity, only heave motion which will be considered in this preliminary study. The dimension of the generator is designed based on the dimension of the ship. Moreover, in order to designed an optimal design of rotor and stator, the average vertical displacement of heave motion is needed. For this purpose, a numerical method called New Strip Method (NSM) is employed to compute the motions of the ship. With NSM, the ship hull is divided into several strips and the hydrodynamics forces are computed on each strip. Moreover, because the ship is assumed to be slender, the total forces are obtained by integrating the force on each strip. After the motions can be determined, the optimal design of the generator is designed and simulated. The performance of the generator in terms of force, magnetic flux, losses, current and induced voltage which are the primary parameters of the linear generator performance, are evaluated using a finite element analysis software named Maxwell. From the study, a linear generator for converting heave motions is designed so that the produced power from the designed generator can be determined.

Practical solutions for reducing container ships' waiting times at ports using simulation model

NASA Astrophysics Data System (ADS)

Sheikholeslami, Abdorreza; Ilati, Gholamreza; Yeganeh, Yones Eftekhari

2013-12-01

The main challenge for container ports is the planning required for berthing container ships while docked in port. Growth of containerization is creating problems for ports and container terminals as they reach their capacity limits of various resources which increasingly leads to traffic and port congestion. Good planning and management of container terminal operations reduces waiting time for liner ships. Reducing the waiting time improves the terminal's productivity and decreases the port difficulties. Two important keys to reducing waiting time with berth allocation are determining suitable access channel depths and increasing the number of berths which in this paper are studied and analyzed as practical solutions. Simulation based analysis is the only way to understand how various resources interact with each other and how they are affected in the berthing time of ships. We used the Enterprise Dynamics software to produce simulation models due to the complexity and nature of the problems. We further present case study for berth allocation simulation of the biggest container terminal in Iran and the optimum access channel depth and the number of berths are obtained from simulation results. The results show a significant reduction in the waiting time for container ships and can be useful for major functions in operations and development of container ship terminals.

Ship detection based on rotation-invariant HOG descriptors for airborne infrared images

NASA Astrophysics Data System (ADS)

Xu, Guojing; Wang, Jinyan; Qi, Shengxiang

2018-03-01

Infrared thermal imagery is widely used in various kinds of aircraft because of its all-time application. Meanwhile, detecting ships from infrared images attract lots of research interests in recent years. In the case of downward-looking infrared imagery, in order to overcome the uncertainty of target imaging attitude due to the unknown position relationship between the aircraft and the target, we propose a new infrared ship detection method which integrates rotation invariant gradient direction histogram (Circle Histogram of Oriented Gradient, C-HOG) descriptors and the support vector machine (SVM) classifier. In details, the proposed method uses HOG descriptors to express the local feature of infrared images to adapt to changes in illumination and to overcome sea clutter effects. Different from traditional computation of HOG descriptor, we subdivide the image into annular spatial bins instead of rectangle sub-regions, and then Radial Gradient Transform (RGT) on the gradient is applied to achieve rotation invariant histogram information. Considering the engineering application of airborne and real-time requirements, we use SVM for training ship target and non-target background infrared sample images to discriminate real ships from false targets. Experimental results show that the proposed method has good performance in both the robustness and run-time for infrared ship target detection with different rotation angles.

KSC-06pd2645

NASA Image and Video Library

2006-12-01

KENNEDY SPACE CENTER, FLA. -- The X-band radar array is installed on the solid rocket booster retrieval ship Liberty before launch of Space Shuttle Discovery. It is one of two Weibel Continuous Pulse Doppler X-band radars located on each of the two SRB retrieval ships. This one will be located downrange of the launch site. Working with the land-based C-band radar, the X-band radars provide velocity and differential shuttle/debris motion information during launch. The radar data will be sent from the ships via satellite link and analyzed at the C-band radar site located on north Kennedy Space Center. Photo credit: NASA/George Shelton

KSC-06pd2643

NASA Image and Video Library

2006-12-01

KENNEDY SPACE CENTER, FLA. -- The X-band radar array is installed on the solid rocket booster retrieval ship Liberty before launch of Space Shuttle Discovery. It is one of two Weibel Continuous Pulse Doppler X-band radars located on each of the two SRB retrieval ships. This one will be located downrange of the launch site. Working with the land-based C-band radar, the X-band radars provide velocity and differential shuttle/debris motion information during launch. The radar data will be sent from the ships via satellite link and analyzed at the C-band radar site located on north Kennedy Space Center. Photo credit: NASA/George Shelton

KSC-06pd2646

NASA Image and Video Library

2006-12-01

KENNEDY SPACE CENTER, FLA. -- The X-band radar array is installed on the solid rocket booster retrieval ship Liberty before launch of Space Shuttle Discovery. It is one of two Weibel Continuous Pulse Doppler X-band radars located on each of the two SRB retrieval ships. This one will be located downrange of the launch site. Working with the land-based C-band radar, the X-band radars provide velocity and differential shuttle/debris motion information during launch. The radar data will be sent from the ships via satellite link and analyzed at the C-band radar site located on north Kennedy Space Center. Photo credit: NASA/George Shelton

KSC-06pd2642

NASA Image and Video Library

2006-12-01

KENNEDY SPACE CENTER, FLA. -- The X-band radar array is being installed on the solid rocket booster retrieval ship Liberty before launch of Space Shuttle Discovery. It is one of two Weibel Continuous Pulse Doppler X-band radars located on each of the two SRB retrieval ships. This one will be located downrange of the launch site. Working with the land-based C-band radar, the X-band radars provide velocity and differential shuttle/debris mo¬tion information during launch. The radar data will be sent from the ships via satellite link and analyzed at the C-band radar site located on north Kennedy Space Center. Photo credit: NASA/George Shelton

KSC-06pd2644

NASA Image and Video Library

2006-12-01

KENNEDY SPACE CENTER, FLA. -- The X-band radar array is installed on the solid rocket booster retrieval ship Liberty before launch of Space Shuttle Discovery. It is one of two Weibel Continuous Pulse Doppler X-band radars located on each of the two SRB retrieval ships. This one will be located downrange of the launch site. Working with the land-based C-band radar, the X-band radars provide velocity and differential shuttle/debris motion information during launch. The radar data will be sent from the ships via satellite link and analyzed at the C-band radar site located on north Kennedy Space Center. Photo credit: NASA/George Shelton

Ship localization in Santa Barbara Channel using machine learning classifiers.

PubMed

Niu, Haiqiang; Ozanich, Emma; Gerstoft, Peter

2017-11-01

Machine learning classifiers are shown to outperform conventional matched field processing for a deep water (600 m depth) ocean acoustic-based ship range estimation problem in the Santa Barbara Channel Experiment when limited environmental information is known. Recordings of three different ships of opportunity on a vertical array were used as training and test data for the feed-forward neural network and support vector machine classifiers, demonstrating the feasibility of machine learning methods to locate unseen sources. The classifiers perform well up to 10 km range whereas the conventional matched field processing fails at about 4 km range without accurate environmental information.

Mapping cumulative noise from shipping to inform marine spatial planning.

PubMed

Erbe, Christine; MacGillivray, Alexander; Williams, Rob

2012-11-01

Including ocean noise in marine spatial planning requires predictions of noise levels on large spatiotemporal scales. Based on a simple sound transmission model and ship track data (Automatic Identification System, AIS), cumulative underwater acoustic energy from shipping was mapped throughout 2008 in the west Canadian Exclusive Economic Zone, showing high noise levels in critical habitats for endangered resident killer whales, exceeding limits of "good conservation status" under the EU Marine Strategy Framework Directive. Error analysis proved that rough calculations of noise occurrence and propagation can form a basis for management processes, because spending resources on unnecessary detail is wasteful and delays remedial action.

CCHDO: Data Management for US and International GO-SHIP and Related Programs

NASA Astrophysics Data System (ADS)

Diggs, S. C.

2016-02-01

An ever-expanding universe of oceanographic data that includes ship-based measurements (CTD, Nutrients, CFCs, etc.) - as well as the data collected from floats, drifters, gliders and moorings - are continuously gathered, scrutinized, documented and disseminated by the CLIVAR and Carbon Hydrographic Data Office (CCHDO) at Scripps Institution of Oceanography. As the official data assembly center for US GO-SHIP (a decadal global hydrography program) the CCHDO is involved in setting and promoting standards of modern data exchange - from observations at sea to final archive. Established in 1996, the CCHDO has a solid history of curating the highest quality full-depth hydrographic data and associated documentation, metadata and DOIs on an API-based web site that provides data in multiple formats and platforms that have been specifically requested by the hydrographic research community. The CCHDO's website, programming platforms, and documentation standards constantly evolve, based on the feedback we receive from the hydrographic community. Technical convergence and collaboration with organizations that include CDIAC, Princeton, NOAA/NCEI, Argo, OceanSITES, BCO-DMO and GO-SHIP is central to our success. We were early adopters of small crowd-sourcing for quality control, and by being involved in all aspects of data use we reintegrate suggested changes to the data, flags and documentation supplied by the most highly recognized and regarded hydrography researchers and institutions in the world.

Instructions for Plastic Encapsulated Microcircuit(PEM) Selection, Screening and Qualification.

NASA Technical Reports Server (NTRS)

King, Terry; Teverovsky, Alexander; Leidecker, Henning

2002-01-01

The use of Plastic Encapsulated Microcircuits (PEMs) is permitted on NASA Goddard Space Flight Center (GSFC) spaceflight applications, provided each use is thoroughly evaluated for thermal, mechanical, and radiation implications of the specific application and found to meet mission requirements. PEMs shall be selected for their functional advantage and availability, not for cost saving; the steps necessary to ensure reliability usually negate any initial apparent cost advantage. A PEM shall not be substituted for a form, fit and functional equivalent, high reliability, hermetic device in spaceflight applications. Due to the rapid change in wafer-level designs typical of commercial parts and the unknown traceability between packaging lots and wafer lots, lot specific testing is required for PEMs, unless specifically excepted by the Mission Assurance Requirements (MAR) for the project. Lot specific qualification, screening, radiation hardness assurance analysis and/or testing, shall be consistent with the required reliability level as defined in the MAR. Developers proposing to use PEMs shall address the following items in their Performance Assurance Implementation Plan: source selection (manufacturers and distributors), storage conditions for all stages of use, packing, shipping and handling, electrostatic discharge (ESD), screening and qualification testing, derating, radiation hardness assurance, test house selection and control, data collection and retention.

An error analysis of the recovery capability of the relative sea-surface profile over the Puerto Rican trench from multi-station and ship tracking of GEOS-2

NASA Technical Reports Server (NTRS)

Stanley, H. R.; Martin, C. F.; Roy, N. A.; Vetter, J. R.

1971-01-01

Error analyses were performed to examine the height error in a relative sea-surface profile as determined by a combination of land-based multistation C-band radars and optical lasers and one ship-based radar tracking the GEOS 2 satellite. It was shown that two relative profiles can be obtained: one using available south-to-north passes of the satellite and one using available north-to-south type passes. An analysis of multi-station tracking capability determined that only Antigua and Grand Turk radars are required to provide satisfactory orbits for south-to-north type satellite passes, while a combination of Merritt Island, Bermuda, and Wallops radars provide secondary orbits for north-to-south passes. Analysis of ship tracking capabilities shows that high elevation single pass range-only solutions are necessary to give only moderate sensitivity to systematic error effects.

NASA's Ship-Aircraft Bio-Optical Research (SABOR)

NASA Image and Video Library

2017-12-08

Storm in the Sargasso Sea Scientist aboard the R/V Endeavor in the Sargasso Sea put their research on hold on July 28, 2014, as a storm system brought high waves crashing onto the deck. NASA's Ship-Aircraft Bio-Optical Research (SABOR) experiment is a coordinated ship and aircraft observation campaign off the Atlantic coast of the United States, an effort to advance space-based capabilities for monitoring microscopic plants that form the base of the marine food chain. Read more: 1.usa.gov/WWRVzj Credit: NASA/SABOR/Chris Armanetti, University of Rhode Island .NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

An improved CS-LSSVM algorithm-based fault pattern recognition of ship power equipments.

PubMed

Yang, Yifei; Tan, Minjia; Dai, Yuewei

2017-01-01

A ship power equipments' fault monitoring signal usually provides few samples and the data's feature is non-linear in practical situation. This paper adopts the method of the least squares support vector machine (LSSVM) to deal with the problem of fault pattern identification in the case of small sample data. Meanwhile, in order to avoid involving a local extremum and poor convergence precision which are induced by optimizing the kernel function parameter and penalty factor of LSSVM, an improved Cuckoo Search (CS) algorithm is proposed for the purpose of parameter optimization. Based on the dynamic adaptive strategy, the newly proposed algorithm improves the recognition probability and the searching step length, which can effectively solve the problems of slow searching speed and low calculation accuracy of the CS algorithm. A benchmark example demonstrates that the CS-LSSVM algorithm can accurately and effectively identify the fault pattern types of ship power equipments.

Sensorless control of ship propulsion interior permanent magnet synchronous motor based on a new sliding mode observer.

PubMed

Ren, Jun-Jie; Liu, Yan-Cheng; Wang, Ning; Liu, Si-Yuan

2015-01-01

This paper proposes a sensorless speed control strategy for ship propulsion interior permanent magnet synchronous motor (IPMSM) based on a new sliding-mode observer (SMO). In the SMO the low-pass filter and the method of arc-tangent calculation of extended electromotive force (EMF) or phase-locked loop (PLL) technique are not used. The calculation of the rotor speed is deduced from the Lyapunov function stability analysis. In order to reduce system chattering, sigmoid functions with switching gains being adaptively updated by fuzzy logic systems are innovatively incorporated into the SMO. Finally, simulation results for a 4.088 MW ship propulsion IPMSM and experimental results from a 7.5 kW IPMSM drive are provided to verify the effectiveness of the proposed SMO method. Copyright © 2014 ISA. Published by Elsevier Ltd. All rights reserved.

NASA's Ship-Aircraft Bio-Optical Research (SABOR)

NASA Image and Video Library

2014-08-25

Catnap at Sea Ali Chase of the University of Maine, and Courtney Kearney of the Naval Research Laboratory, caught a quick nap on July 24, 2014, while between successive stops at sea to make measurements from the R/V Endeavor. NASA's Ship-Aircraft Bio-Optical Research (SABOR) experiment is a coordinated ship and aircraft observation campaign off the Atlantic coast of the United States, an effort to advance space-based capabilities for monitoring microscopic plants that form the base of the marine food chain. Read more: 1.usa.gov/WWRVzj Credit: NASA/SABOR/Wayne Slade, Sequoia Scientific..NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

Numerical study on wave loads and motions of two ships advancing in waves by using three-dimensional translating-pulsating source

NASA Astrophysics Data System (ADS)

Xu, Yong; Dong, Wen-Cai

2013-08-01

A frequency domain analysis method based on the three-dimensional translating-pulsating (3DTP) source Green function is developed to investigate wave loads and free motions of two ships advancing on parallel course in waves. Two experiments are carried out respectively to measure the wave loads and the freemotions for a pair of side-byside arranged ship models advancing with an identical speed in head regular waves. For comparison, each model is also tested alone. Predictions obtained by the present solution are found in favorable agreement with the model tests and are more accurate than the traditional method based on the three dimensional pulsating (3DP) source Green function. Numerical resonances and peak shift can be found in the 3DP predictions, which result from the wave energy trapped in the gap between two ships and the extremely inhomogeneous wave load distribution on each hull. However, they can be eliminated by 3DTP, in which the speed affects the free surface and most of the wave energy can be escaped from the gap. Both the experiment and the present prediction show that hydrodynamic interaction effects on wave loads and free motions are significant. The present solver may serve as a validated tool to predict wave loads and motions of two vessels under replenishment at sea, and may help to evaluate the hydrodynamic interaction effects on the ships safety in replenishment operation.

Technical comparison of several global mobile satellite communications systems

NASA Astrophysics Data System (ADS)

Comparetto, Gary M.

The era of satellite-based mobile satellite communications (MSC) systems started with the first MARISAT satellite which was launched into a geostationary orbit over the Pacific Ocean in 1976 to provide communications between ships and shore stations. The combination of high cost and unacceptably large equipment has kept the space-based MSC systems from appealing to the wider market of personal mobile communications. The progress made over the last ten years, however, in digital voice processing, satellite technology, and component miniaturization has resulted in the viability of satellite-based mobile satellite communications systems to meet the growing market in personal mobile communications using handsets similar to those currently in use with land-based cellular systems. Three of the more mature LEO/MEO satellite systems are addressed in this paper including GLOBALSTAR, Iridium, and Odyssey. The system architectures of each system are presented along with a description of the satellite and user handset designs and the multiaccess techniques employed. It will be shown that, although a number of similarities exist among the system addressed, each system is unique in a variety of significant design areas. It is concluded that the technical feasibility of satellite-based mobile satellite communications systems seems to be secure. It will be challenging, however, for the vendors to actually develop and deploy these systems in a cost effective, timely, and reliable way that meets a continually evolving set of requirements based upon a rapidly changing technology base.

Inter-annual trend of the primary contribution of ship emissions to PM2.5 concentrations in Venice (Italy): Efficiency of emissions mitigation strategies

NASA Astrophysics Data System (ADS)

Contini, Daniele; Gambaro, Andrea; Donateo, Antonio; Cescon, Paolo; Cesari, Daniela; Merico, Eva; Belosi, Franco; Citron, Marta

2015-02-01

Ships and harbour emissions are currently increasing, due to the increase of tourism and trade, with potential impact on global air pollution and climate. At local scale, in-port ship emissions influence air quality in coastal areas impacting on health of coastal communities. International legislations to reduce ship emissions, both at Worldwide and European levels, are mainly based on the use of low-sulphur content fuel. In this work an analysis of the inter-annual trends of primary contribution, ε, of tourist shipping to the atmospheric PM2.5 concentrations in the urban area of Venice has been performed. Measurements have been taken in the summer periods of 2007, 2009 and 2012. Results show a decrease of ε from 7% (±1%) in 2007 to 5% (±1%) in 2009 and to 3.5% (±1%) in 2012. The meteorological and micrometeorological conditions of the campaigns were similar. Tourist ship traffic during measurement campaigns increased, in terms of gross tonnage, of about 25.4% from 2007 to 2009 and of 17.6% from 2009 to 2012. The decrease of ε was associated to the effect of a voluntary agreement (Venice Blue Flag) for the use of low-sulphur content fuel enforced in the area between 2007 and 2009 and to the implementation of the 2005/33/CE Directive in 2010. Results show that the use of low-sulphur fuel could effectively reduce the impact of shipping to atmospheric primary particles at local scale. Further, voluntary agreement could also be effective in reducing the impact of shipping on local air quality in coastal areas.

Disturbance of a rare seabird by ship-based tourism in a marine protected area

USGS Publications Warehouse

Marcella, Timothy K.; Gende, Scott M.; Roby, Daniel D.; Allignol, Arthur

2017-01-01

Managers of marine protected areas (MPAs) must often seek ways to allow for visitation while minimizing impacts to the resources they are intended to protect. Using shipboard observers, we quantified the “zone of disturbance” for Kittlitz’s and marbled murrelets (Brachyramphus brevirostris and B. marmoratus) exposed to large cruise ships traveling through Glacier Bay National Park, one of the largest MPAs in North America. In the upper reaches of Glacier Bay, where Kittlitz’s murrelets predominated, binary logistic regression models predicted that 61% of all murrelets within 850 m perpendicular distance of a cruise ship were disturbed (defined as flushing or diving), whereas in the lower reaches, where marbled murrelets predominated, this percentage increased to 72%. Using survival analysis, murrelets in both reaches were found to react at greater distances when ships approached indirectly, presumably because of the ship’s larger profile, suggesting murrelets responded to visual rather than audio cues. No management-relevant covariates (e.g., ship velocity, route distance from shore) were found to be important predictors of disturbance, as distance from ship to murrelet accounted for > 90% of the explained variation in murrelet response. Utilizing previously published murrelet density estimates from Glacier Bay, and applying an average empirical disturbance probability (68%) out to 850 m from a cruise ship’s typical route, we estimated that a minimum of 9.8–19.6% of all murrelets in Glacier Bay are disturbed per ship entry. Whether these disturbance levels are inconsistent with Park management objectives, which include conserving wildlife as well as providing opportunities for visitation, depends in large part on whether disturbance events caused by cruise ships have impacts on murrelet fitness, which remains uncertain.

Healthcare delivery aboard US Navy hospital ships following earthquake disasters: implications for future disaster relief missions.

PubMed

Sechriest, V Franklin; Wing, Vern; Walker, G Jay; Aubuchon, Maureen; Lhowe, David W

2012-01-01

Since 2004, the US Navy has provided ship-borne medical assistance during three earthquake disasters. Because Navy ship deployment for disaster relief (DR) is a recent development, formal guidelines for equipping and staffing medical operations do not yet exist. The goal of this study was to inform operational planning and resource allocation for future earthquake DR missions by 1) reporting the type and volume of patient presentations, medical staff, and surgical services and 2) providing a comparative analysis of the current medical and surgical capabilities of a hospital ship and a casualty receiving and treatment ship (CRTS). The following three earthquake DR operations were reviewed retrospectively: 1) USNS Mercy to Indonesia in 2004, 2) USNS Mercy to Indonesia in 2005, and 3) USNS Comfort/USS Bataan to Haiti in 2010. (The USS Bataan was a CRTS.) Mission records and surgical logs were analyzed. Descriptive and statistical analysis was performed. Comparative analysis of hospital ship and CRTS platforms was made based on firsthand observations. For the three missions, 986 patient encounters were documented. Of 1,204 diagnoses, 80 percent were disaster-related injuries, more than half of which were extremity trauma. Aboard hospital ships, healthcare staff provided advanced (Echelon III) care for disaster-related injuries and various nondisaster-related conditions. Aboard the CRTS, staff provided basic (Echelon II) care for disaster-related injuries. Our data indicate that musculoskeletal extremity injuries in sex- and age-diverse populations comprised the majority of clinical diagnoses. Current capabilities and surgical staffing of hospital ships and CRTS platforms influenced their respective DR operations, including the volume and types of surgical care delivered.

Disturbance of a rare seabird by ship-based tourism in a marine protected area

PubMed Central

Allignol, Arthur

2017-01-01

Managers of marine protected areas (MPAs) must often seek ways to allow for visitation while minimizing impacts to the resources they are intended to protect. Using shipboard observers, we quantified the “zone of disturbance” for Kittlitz’s and marbled murrelets (Brachyramphus brevirostris and B. marmoratus) exposed to large cruise ships traveling through Glacier Bay National Park, one of the largest MPAs in North America. In the upper reaches of Glacier Bay, where Kittlitz’s murrelets predominated, binary logistic regression models predicted that 61% of all murrelets within 850 m perpendicular distance of a cruise ship were disturbed (defined as flushing or diving), whereas in the lower reaches, where marbled murrelets predominated, this percentage increased to 72%. Using survival analysis, murrelets in both reaches were found to react at greater distances when ships approached indirectly, presumably because of the ship’s larger profile, suggesting murrelets responded to visual rather than audio cues. No management-relevant covariates (e.g., ship velocity, route distance from shore) were found to be important predictors of disturbance, as distance from ship to murrelet accounted for > 90% of the explained variation in murrelet response. Utilizing previously published murrelet density estimates from Glacier Bay, and applying an average empirical disturbance probability (68%) out to 850 m from a cruise ship’s typical route, we estimated that a minimum of 9.8–19.6% of all murrelets in Glacier Bay are disturbed per ship entry. Whether these disturbance levels are inconsistent with Park management objectives, which include conserving wildlife as well as providing opportunities for visitation, depends in large part on whether disturbance events caused by cruise ships have impacts on murrelet fitness, which remains uncertain. PMID:28489902

The growing contribution of sulfur emissions from ships in Asian waters, 1988-1995

NASA Astrophysics Data System (ADS)

Streets, David G.; Guttikunda, Sarath K.; Carmichael, Gregory R.

International shipping is a major source of sulfur emissions in Asia. Because the fuel oil used by ships is high in sulfur, the resulting emissions of SO 2 are large and contribute as much as 20% to the atmospheric loading in the vicinity of ports and heavily traveled waterways. Because of the rapid growth of Asian economies in the 1980s and early 1990s, it is estimated that shipping trade grew by an average of 5.4% per year between 1988 and 1995; in particular, crude oil shipments to Asian countries other than Japan grew by an average of 11.4% per year. The emissions of SO 2 from shipping are estimated to have grown by 5.9% per year between 1988 and 1995, rising from 545 Gg in 1988 to 817 Gg in 1995. This study uses the ATMOS atmospheric transport and deposition model to study the effects of these emissions, both in absolute terms and relative to land-based emissions , on wet and dry deposition of sulfur. Southeast Asia is most heavily affected by emissions from ships, particularly Sumatra, peninsular Malaysia, and Singapore, which routinely receive in excess of 10% of their deposition from ships. A strong seasonal component is also observed, with large areas of Southeast Asia and coastal Japan receiving sulfur deposition that exceeds 10 mg S m -2 season -1. Deposition is at least 25% higher in summer and fall than in winter and spring. Peak values of 25-50 mg S m -2 season -1 are calculated for winter in the Strait of Malacca. This work suggests a need to introduce policies to reduce the sulfur content of marine fuels or otherwise reduce emissions of SO 2 from ships in Asian waters.

AUTOCASK (AUTOmatic Generation of 3-D CASK models). A microcomputer based system for shipping cask design review analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gerhard, M.A.; Sommer, S.C.

1995-04-01

AUTOCASK (AUTOmatic Generation of 3-D CASK models) is a microcomputer-based system of computer programs and databases developed at the Lawrence Livermore National Laboratory (LLNL) for the structural analysis of shipping casks for radioactive material. Model specification is performed on the microcomputer, and the analyses are performed on an engineering workstation or mainframe computer. AUTOCASK is based on 80386/80486 compatible microcomputers. The system is composed of a series of menus, input programs, display programs, a mesh generation program, and archive programs. All data is entered through fill-in-the-blank input screens that contain descriptive data requests.

The Distributed Air Wing

DTIC Science & Technology

2014-06-01

Cruise Missile LCS Littoral Combat Ship LEO Low Earth Orbit LER Loss-Exchange-Ration LHA Landing Helicopter Assault LIDAR Laser Imaging Detection and...Ranging LOC Lines of Communication LP Linear Programming LRASM Long Range Anti-Ship Missile LT Long Ton MANA Map-Aware Non-uniform Automata ME...enemy’s spy satellites. Based on open source information, China currently has 25 satellites operating in Low Earth Orbit ( LEO ), each operates at an

Operational Products Archived at the National Snow and Ice Data Center

NASA Astrophysics Data System (ADS)

Fetterer, F. M.; Ballagh, L.; Gergely, K.; Kovarik, J.; Wallace, A.; Windnagel, A.

2009-12-01

Sea ice charts for shipping interests from the Navy/NOAA/Coast Guard National Ice Center are often laboriously produced by manually interpreting and synthesizing data from many sources, both satellite and in situ. They are generally more accurate than similar products from single sources. Upward looking sonar data from U.S. Navy submarines operating in the Arctic provides information on ice thickness. Similarly extensive data were available from no other source prior to the recently established reliability of ice thickness estimates from polar orbiting instruments like the Geoscience Laser Altimeter System (GLAS). Snow Data Assimilation System (SNODAS) products from the NOAA NWS National Operational Hydrologic Remote Sensing Center give researchers the best possible estimates of snow cover and associated variables to support hydrologic modeling and analysis for the continental U.S. These and other snow and ice data products are produced by the U.S. Navy, the NOAA National Weather Service, and other agency entities to serve users who have an operational need: to get a ship safely to its destination, for example, or to predict stream flow. NOAA supports work at NSIDC with data from operational sources that can be used for climate research and change detection. We make these products available to a new user base, by archiving operational data, making data available online, providing documentation, and fielding questions from researchers about the data. These data demand special consideration: often they are advantageous because they are available on a schedule in near real time, but their use in climate studies is problematic since many are produced with regard for ‘best now’ and without regard for time series consistency. As arctic climate changes rapidly, operational and semi-operational products have an expanding science support role to play.

Effectiveness of maritime safety control in different navigation zones using a spatial sequential DEA model: Yangtze River case.

PubMed

Wu, Bing; Wang, Yang; Zhang, Jinfen; Savan, Emanuel Emil; Yan, Xinping

2015-08-01

This paper aims to analyze the effectiveness of maritime safety control from the perspective of safety level along the Yangtze River with special considerations for navigational environments. The influencing variables of maritime safety are reviewed, including ship condition, maritime regulatory system, human reliability and navigational environment. Because the former three variables are generally assumed to be of the same level of safety, this paper focuses on studying the impact of navigational environments on the level of safety in different waterways. An improved data envelopment analysis (DEA) model is proposed by treating the navigational environment factors as inputs and ship accident data as outputs. Moreover, because the traditional DEA model cannot provide an overall ranking of different decision making units (DMUs), the spatial sequential frontiers and grey relational analysis are incorporated into the DEA model to facilitate a refined assessment. Based on the empirical study results, the proposed model is able to solve the problem of information missing in the prior models and evaluate the level of safety with a better accuracy. The results of the proposed DEA model are further compared with an evidential reasoning (ER) method, which has been widely used for level of safety evaluations. A sensitivity analysis is also conducted to better understand the relationship between the variation of navigational environments and level of safety. The sensitivity analysis shows that the level of safety varies in terms of traffic flow. It indicates that appropriate traffic control measures should be adopted for different waterways to improve their safety. This paper presents a practical method of conducting maritime level of safety assessments under dynamic navigational environment. Copyright © 2015 Elsevier Ltd. All rights reserved.

Assured crew return capability Crew Emergency Return Vehicle (CERV) avionics

NASA Technical Reports Server (NTRS)

Myers, Harvey Dean

1990-01-01

The Crew Emergency Return Vehicle (CERV) is being defined to provide Assured Crew Return Capability (ACRC) for Space Station Freedom. The CERV, in providing the standby lifeboat capability, would remain in a dormat mode over long periods of time as would a lifeboat on a ship at sea. The vehicle must be simple, reliable, and constantly available to assure the crew's safety. The CERV must also provide this capability in a cost effective and affordable manner. The CERV Project philosophy of a simple vehicle is to maximize its useability by a physically deconditioned crew. The vehicle reliability goes unquestioned since, when needed, it is the vehicle of last resort. Therefore, its systems and subsystems must be simple, proven, state-of-the-art technology with sufficient redundancy to make it available for use as required for the life of the program. The CERV Project Phase 1'/2 Request for Proposal (RFP) is currently scheduled for release on October 2, 1989. The Phase 1'/2 effort will affirm the existing project requirements or amend and modify them based on a thorough evaluation of the contractor(s) recommendations. The system definition phase, Phase 2, will serve to define CERV systems and subsystems. The current CERV Project schedule has Phase 2 scheduled to begin October 1990. Since a firm CERV avionics design is not in place at this time, the treatment of the CERV avionics complement for the reference configuration is not intended to express a preference with regard to a system or subsystem.

A distributed control approach for power and energy management in a notional shipboard power system

NASA Astrophysics Data System (ADS)

Shen, Qunying

The main goal of this thesis is to present a power control module (PCON) based approach for power and energy management and to examine its control capability in shipboard power system (SPS). The proposed control scheme is implemented in a notional medium voltage direct current (MVDC) integrated power system (IPS) for electric ship. To realize the control functions such as ship mode selection, generator launch schedule, blackout monitoring, and fault ride-through, a PCON based distributed power and energy management system (PEMS) is developed. The control scheme is proposed as two-layer hierarchical architecture with system level on the top as the supervisory control and zonal level on the bottom as the decentralized control, which is based on the zonal distribution characteristic of the notional MVDC IPS that was proposed as one of the approaches for Next Generation Integrated Power System (NGIPS) by Norbert Doerry. Several types of modules with different functionalities are used to derive the control scheme in detail for the notional MVDC IPS. Those modules include the power generation module (PGM) that controls the function of generators, the power conversion module (PCM) that controls the functions of DC/DC or DC/AC converters, etc. Among them, the power control module (PCON) plays a critical role in the PEMS. It is the core of the control process. PCONs in the PEMS interact with all the other modules, such as power propulsion module (PPM), energy storage module (ESM), load shedding module (LSHED), and human machine interface (HMI) to realize the control algorithm in PEMS. The proposed control scheme is implemented in real time using the real time digital simulator (RTDS) to verify its validity. To achieve this, a system level energy storage module (SESM) and a zonal level energy storage module (ZESM) are developed in RTDS to cooperate with PCONs to realize the control functionalities. In addition, a load shedding module which takes into account the reliability of power supply (in terms of quality of service) is developed. This module can supply uninterruptible power to the mission critical loads. In addition, a multi-agent system (MAS) based framework is proposed to implement the PCON based PEMS through a hardware setup that is composed of MAMBA boards and FPGA interface. Agents are implemented using Java Agent DEvelopment Framework (JADE). Various test scenarios were tested to validate the approach.

Emissions from international shipping: 2. Impact of future technologies on scenarios until 2050

NASA Astrophysics Data System (ADS)

Eyring, V.; KöHler, H. W.; Lauer, A.; Lemper, B.

2005-09-01

In this study the today's fleet-average emission factors of the most important ship exhausts are used to calculate emission scenarios for the future. To develop plausible future technology scenarios, first upcoming regulations and compliance with future regulations through technological improvements are discussed. We present geographically resolved emission inventory scenarios until 2050, based on a mid-term prognosis for 2020 and a long-term prognosis for 2050. The scenarios are based on some very strict assumptions on future ship traffic demands and technological improvements. The four future ship traffic demand scenarios are mainly determined by the economic growth, which follows the IPCC SRES storylines. The resulting fuel consumption is projected through extrapolations of historical trends in economic growth, total seaborne trade and number of ships, as well as the average installed power per ship. For the future technology scenarios we assume a diesel-only fleet in 2020 resulting in fuel consumption between 382 and 409 million metric tons (Mt). For 2050 one technology scenario assumes that 25% of the fuel consumed by a diesel-only fleet can be saved by applying future alternative propulsion plants, resulting in a fuel consumption that varies between 402 and 543 Mt. The other scenario is a business-as-usual scenario for a diesel-only fleet even in 2050 and gives an estimate between 536 and 725 Mt. Dependent on how rapid technology improvements for diesel engines are introduced, possible technology reduction factors are applied to the today's fleet-average emission factors of all important species to estimate future ship emissions. Combining the four traffic demand scenarios with the four technology scenarios, our results suggest emissions between 8.8 and 25.0 Tg (NO2) in 2020, and between 3.1 to 38.8 Tg (NO2) in 2050. The development of forecast scenarios for CO2, NOx, SOx, CO, hydrocarbons, and particulate matter is driven by the requirements for global model studies of the effects of these emissions on the chemical composition of the atmosphere and on climate. The developed scenarios are suitable for use as input for chemical transport models (CTMs) and coupled chemistry-climate models (CCMs).

New directions: Beyond sulphur, vanadium and nickel - About source apportionment of ship emissions in emission control areas

NASA Astrophysics Data System (ADS)

Czech, Hendryk; Schnelle-Kreis, Jürgen; Streibel, Thorsten; Zimmermann, Ralf

2017-08-01

During the oil crises of the 70s and the associated increase of the oil price, the usage of marine fuels shifted from middle distillates of the crude oil refinery, such as marine diesel oil (MDO) or marine gas oil (MGO), towards cheaper heavy fuel oils (HFO), or also called residual fuel oil. The latter refers to the vacuum residue of the crude oil refinery blended by lighter refinery products, such as kerosene, to meet a certain maximum viscosity. Those HFOs are rich in sulphur and heavy metals which end up as significant constituents in emitted fine particulate matter (PM2.5) after the combustion. Especially for harbour cities or highly frequented ship traffic routes, HFO-derived PM2.5 has been identified as a globally important perpetrator of increased mortality by cardiopulmonary diseases and lung cancer (e.g. Corbett et al., 2007). However, the emitted hazardous species provide reliable markers to assess the contribution of this emission source to air pollution in source apportionment studies. Such studies are often performed utilising positive matrix factorisation, whose score matrix can be interpreted as temporal contribution of k identified emission sources and factors represent the k corresponding emission profiles. If one of the k factors contains moderate to high amounts of sulphate, vanadium and nickel with a high ratio of the two latter ones, the ship identification was unambiguous (e.g. Viana et al., 2009). Even more sensitive towards emission profiles are receptor models such as chemical mass balance, which require detailed prior knowledge about the assumed emission sources (Jeong et al., 2017).

Design of a leak detection device for marine airtight container

NASA Astrophysics Data System (ADS)

Li, Yuan; Zhu, Faxin; Lu, Jinshu; Li, Yule; Wu, Wenfeng; Zhang, Jianwei; Qin, Beichen

2018-04-01

The ship airtight container as the research object, according to the tightness of the traditional detection methods of sealed container from the shortcomings of the design of modern ship sealed container leak detection device based on the requirements of the use of AutoCAD to design a ship leakage detection device using airtight container, and introduces its working principle and main components. Finally, from the aspects of technology, structure, operation and economy, the feasibility analysis of the leak detection device for marine airtight container is designed, and it is concluded that the device has the advantages of simple operation, short detection time, easy maintenance and cost control, and has high feasibility.

3D Viscous Free-Surface Flow around a Combatant Ship Hull

NASA Astrophysics Data System (ADS)

Pacuraru, Florin; Lungu, Adrian; Maria, Viorel

2009-09-01

The prediction of the total drag experienced by an advancing ship is a complicated problem which requires a thorough understanding of the hydrodynamic forces acting on the hull, the physical processes from which these forces arise and their mutual interaction. A general numerical method to predict the hydrodynamic performance of a twin-propeller combatant ship hull is presented in the paper. For practical reasons, the technique couples a body forces method and a RANS-based finite volume solver to account for the interactions between the hull and the appendages mounted on it: propellers, rudders, shaft lines, bossings and brackets. The chimera approach has been found the most versatile way for grid generation of hull and appendages.

Recent UAS Developments: VTOL HQ-series Shipboard Recovery and Autonomous Monitoring with MicroQuads

NASA Astrophysics Data System (ADS)

Wardell, L. J.; Farber, A. M.; Douglas, J.

2017-12-01

Ocean research would benefit from reliable shipboard launch and recovery of small class UAS. The vertical take-off and landing (VTOL) system reduces equipment footprint without the need for launchers or recovery systems. The HQ-60 (Latitude Engineering) has demonstrated reliable ship take-off and recovery on a 10x10' area on the R/V Falkor (Schmidt Ocean Institute) and other research vessels. The HQ-60 recently set a record for longest time aloft for a VTOL aircraft, flying nearly 22.5 hours non-stop. To support close-range research, autonomous MicroQuads that "perch" in a protective box that also recharges the aircraft and transmits the data is in development. Recent MicroQuad work with developing high-resolution (<1cm) DEMs using on-board cameras has yielded promising results for the use of surface change detection. Recent USDA development targeted erosion monitoring with this system. The latest updates and testing results for both systems will be presented.

46 CFR 42.05-63 - Ship(s) and vessel(s).

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false Ship(s) and vessel(s). 42.05-63 Section 42.05-63 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) LOAD LINES DOMESTIC AND FOREIGN VOYAGES BY SEA Definition of Terms Used in This Subchapter § 42.05-63 Ship(s) and vessel(s). The terms ship(s...

46 CFR 42.05-63 - Ship(s) and vessel(s).

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false Ship(s) and vessel(s). 42.05-63 Section 42.05-63 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) LOAD LINES DOMESTIC AND FOREIGN VOYAGES BY SEA Definition of Terms Used in This Subchapter § 42.05-63 Ship(s) and vessel(s). The terms ship(s...

46 CFR 42.05-63 - Ship(s) and vessel(s).

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false Ship(s) and vessel(s). 42.05-63 Section 42.05-63 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) LOAD LINES DOMESTIC AND FOREIGN VOYAGES BY SEA Definition of Terms Used in This Subchapter § 42.05-63 Ship(s) and vessel(s). The terms ship(s...

46 CFR 42.05-63 - Ship(s) and vessel(s).

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false Ship(s) and vessel(s). 42.05-63 Section 42.05-63 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) LOAD LINES DOMESTIC AND FOREIGN VOYAGES BY SEA Definition of Terms Used in This Subchapter § 42.05-63 Ship(s) and vessel(s). The terms ship(s...

Supplementary Health Insurance from the consumer point of view: Are Israelis consumers doing an informed rational choice when purchasing Supplementary Health Insurance?

PubMed

Kaplan, Giora; Shahar, Yael; Tal, Orna

2017-06-01

The National Health Insurance Law in Israel ensures basic health basket eligibility for all its citizens. A supplemental health insurance plan (SHIP) is offered for an additional fee. Over the years, the percentage of supplemental insurance's holders has risen considerably, ranking among the highest in OECD countries. The assumption that consumers implement an informed rational choice based on relevant information is doubtful. Are consumers sufficiently well informed to make market processes work well? To examine perspectives, preferences and knowledge of Israelis in relation to SHIP. A telephone survey was conducted with a representative sample of the Israeli adult population. 703 interviews were completed. The response rate was 50.3%. 85% of the sample reported possessing SHIP. This survey found that most of the Israeli public parched additional insurance coverage however did not show a significant knowledge about the benefits provided by the supplementary insurance, at least in the three measurements used in this study. The scope of SHIP acquisition is very broad and cannot be explained in economic terms alone. Acquiring SHIP became a default option rather than an active decision. It is time to review the goals, achievements and side effects of SHIP and to create new policy for the future. Copyright © 2017 Elsevier B.V. All rights reserved.

The decision making process on public health measures related to passenger ships: the example of influenza pandemic 2009.

PubMed

Mouchtouri, V A; Bartlett, C L R; Jaremin, Bogdan; Nichols, G; Paux, T; Riemer, T; Black, N; Varela-Martinez, C; Swaan, C M; Schlaich, C; Rachiotis, G; Kremastinou, J; Hadjichristodoulou, C

2010-01-01

Public health measures at sea ports have posed a challenge for public health competent authorities, especially in the context of the influenza pandemic of 2009. This paper discusses the response of authorities to notifications of infectious diseases on passenger ships and the importance of assessing the risks related to cases of influenza. It further provides options for health measures and considerations for decision making during a pandemic such as the influenza pandemic of 2009. Prevention and control of influenza have included action taken by both competent port authorities and ships' crews. Assessing the public health risk of each event reported from ships to competent authorities at ports is important before advice is given on implementation of control measures. Public health risk assessment involves appraisal of threats to passengers and crew on board the ship as well as to the population in the community. Any public health measures taken should be necessary and proportional to the threat. Measures at ports cannot alone be effective in the prevention of the spread of a disease to the community since other means of transport play a major role. Measures taken on board ships can be effective in containing the disease. Consistent policy based on common protocols and carried out by competent authorities at local, national, European, or international levels are essential.

Ship noise extends to frequencies used for echolocation by endangered killer whales

PubMed Central

Veirs, Val; Wood, Jason D.

2016-01-01

Combining calibrated hydrophone measurements with vessel location data from the Automatic Identification System, we estimate underwater sound pressure levels for 1,582 unique ships that transited the core critical habitat of the endangered Southern Resident killer whales during 28 months between March, 2011, and October, 2013. Median received spectrum levels of noise from 2,809 isolated transits are elevated relative to median background levels not only at low frequencies (20–30 dB re 1 µPa2/Hz from 100 to 1,000 Hz), but also at high frequencies (5–13 dB from 10,000 to 96,000 Hz). Thus, noise received from ships at ranges less than 3 km extends to frequencies used by odontocetes. Broadband received levels (11.5–40,000 Hz) near the shoreline in Haro Strait (WA, USA) for the entire ship population were 110 ± 7 dB re 1 µPa on average. Assuming near-spherical spreading based on a transmission loss experiment we compute mean broadband source levels for the ship population of 173 ± 7 dB re 1 µPa 1 m without accounting for frequency-dependent absorption. Mean ship speed was 7.3 ± 2.0 m/s (14.1 ± 3.9 knots). Most ship classes show a linear relationship between source level and speed with a slope near +2 dB per m/s (+1 dB/knot). Spectrum, 1/12-octave, and 1/3-octave source levels for the whole population have median values that are comparable to previous measurements and models at most frequencies, but for select studies may be relatively low below 200 Hz and high above 20,000 Hz. Median source spectrum levels peak near 50 Hz for all 12 ship classes, have a maximum of 159 dB re 1 µPa2/Hz @ 1 m for container ships, and vary between classes. Below 200 Hz, the class-specific median spectrum levels bifurcate with large commercial ships grouping as higher power noise sources. Within all ship classes spectrum levels vary more at low frequencies than at high frequencies, and the degree of variability is almost halved for classes that have smaller speed standard deviations. This is the first study to present source spectra for populations of different ship classes operating in coastal habitats, including at higher frequencies used by killer whales for both communication and echolocation. PMID:27004149

System and Method for Automated Rendezvous, Docking and Capture of Autonomous Underwater Vehicles

NASA Technical Reports Server (NTRS)

Clark, Evan (Inventor); Richmond, Kristof (Inventor); Paulus, Jeremy (Inventor); Kimball, Peter (Inventor); Scully, Mark (Inventor); Kapit, Jason (Inventor); Stone, William C. (Inventor)

2018-01-01

A system for automated rendezvous, docking, and capture of autonomous underwater vehicles at the conclusion of a mission comprising of comprised of a docking rod having lighted, pulsating (in both frequency and light intensity) series of LED light strips thereon, with the LEDs at a known spacing, and the autonomous underwater vehicle specially designed to detect and capture the docking rod and then be lifted structurally by a spherical end strop about which the vehicle can be pivoted and hoisted up (e.g., onto a ship). The method of recovery allows for very routine and reliable automated recovery of an unmanned underwater asset.

Optical Rain Gauge Performance: Second Workshop on Optical Rain Gauge Measurements

NASA Technical Reports Server (NTRS)

Short, David A. (Editor); Thiele, Otto W. (Editor); Mcphaden, Michael J. (Editor)

1994-01-01

The primary focus of the workshop was on the performance and reliability of STi mini-Optical Rain Gauges in a number of environments, including deployments on ships and buoys in the western equatorial Pacific Ocean during the TOGA/COARE field experiment, deployments on buoys in U.S. coastal waters, and comparisons with other types of rain gauges on the Virginia coast and in Florida. The workshop was attended by 20 investigators, representing 10 different institutions, who gathered to present new results obtained since the first workshop (April 1993), to discuss problems, to consider solutions, and to chart future directions. Post-TOGA/COARE calibration studies were also presented.

Resonance-Based Time-Frequency Manifold for Feature Extraction of Ship-Radiated Noise.

PubMed

Yan, Jiaquan; Sun, Haixin; Chen, Hailan; Junejo, Naveed Ur Rehman; Cheng, En

2018-03-22

In this paper, a novel time-frequency signature using resonance-based sparse signal decomposition (RSSD), phase space reconstruction (PSR), time-frequency distribution (TFD) and manifold learning is proposed for feature extraction of ship-radiated noise, which is called resonance-based time-frequency manifold (RTFM). This is suitable for analyzing signals with oscillatory, non-stationary and non-linear characteristics in a situation of serious noise pollution. Unlike the traditional methods which are sensitive to noise and just consider one side of oscillatory, non-stationary and non-linear characteristics, the proposed RTFM can provide the intact feature signature of all these characteristics in the form of a time-frequency signature by the following steps: first, RSSD is employed on the raw signal to extract the high-oscillatory component and abandon the low-oscillatory component. Second, PSR is performed on the high-oscillatory component to map the one-dimensional signal to the high-dimensional phase space. Third, TFD is employed to reveal non-stationary information in the phase space. Finally, manifold learning is applied to the TFDs to fetch the intrinsic non-linear manifold. A proportional addition of the top two RTFMs is adopted to produce the improved RTFM signature. All of the case studies are validated on real audio recordings of ship-radiated noise. Case studies of ship-radiated noise on different datasets and various degrees of noise pollution manifest the effectiveness and robustness of the proposed method.

Resonance-Based Time-Frequency Manifold for Feature Extraction of Ship-Radiated Noise

PubMed Central

Yan, Jiaquan; Sun, Haixin; Chen, Hailan; Junejo, Naveed Ur Rehman; Cheng, En

2018-01-01

In this paper, a novel time-frequency signature using resonance-based sparse signal decomposition (RSSD), phase space reconstruction (PSR), time-frequency distribution (TFD) and manifold learning is proposed for feature extraction of ship-radiated noise, which is called resonance-based time-frequency manifold (RTFM). This is suitable for analyzing signals with oscillatory, non-stationary and non-linear characteristics in a situation of serious noise pollution. Unlike the traditional methods which are sensitive to noise and just consider one side of oscillatory, non-stationary and non-linear characteristics, the proposed RTFM can provide the intact feature signature of all these characteristics in the form of a time-frequency signature by the following steps: first, RSSD is employed on the raw signal to extract the high-oscillatory component and abandon the low-oscillatory component. Second, PSR is performed on the high-oscillatory component to map the one-dimensional signal to the high-dimensional phase space. Third, TFD is employed to reveal non-stationary information in the phase space. Finally, manifold learning is applied to the TFDs to fetch the intrinsic non-linear manifold. A proportional addition of the top two RTFMs is adopted to produce the improved RTFM signature. All of the case studies are validated on real audio recordings of ship-radiated noise. Case studies of ship-radiated noise on different datasets and various degrees of noise pollution manifest the effectiveness and robustness of the proposed method. PMID:29565288

Detecting ship targets in spaceborne infrared image based on modeling radiation anomalies

NASA Astrophysics Data System (ADS)

Wang, Haibo; Zou, Zhengxia; Shi, Zhenwei; Li, Bo

2017-09-01

Using infrared imaging sensors to detect ship target in the ocean environment has many advantages compared to other sensor modalities, such as better thermal sensitivity and all-weather detection capability. We propose a new ship detection method by modeling radiation anomalies for spaceborne infrared image. The proposed method can be decomposed into two stages, where in the first stage, a test infrared image is densely divided into a set of image patches and the radiation anomaly of each patch is estimated by a Gaussian Mixture Model (GMM), and thereby target candidates are obtained from anomaly image patches. In the second stage, target candidates are further checked by a more discriminative criterion to obtain the final detection result. The main innovation of the proposed method is inspired by the biological mechanism that human eyes are sensitive to the unusual and anomalous patches among complex background. The experimental result on short wavelength infrared band (1.560 - 2.300 μm) and long wavelength infrared band (10.30 - 12.50 μm) of Landsat-8 satellite shows the proposed method achieves a desired ship detection accuracy with higher recall than other classical ship detection methods.

A comparison of ship and Coastal Zone Color Scanner mapped distribution of phytoplankton in the southeastern Bering Sea

NASA Technical Reports Server (NTRS)

Mcclain, C. R.; Sambrotto, R. N.; Ray, G. C.; Muller-Karger, F. E.

1990-01-01

Twenty-one Coastal Zone Color Scanner (CZCS) images of the southeastern Bering Sea are examined in order to map the near-surface distribution of phytoplankton during 1979 and 1980. The information is compared with the mesoscale (100-1000 km) distribution of phytoplankton inferred from pooled ship sampling obtained during the Processes and Resources of the Bering Shelf (PROBES) intensive field study during the late 1970s and early 1980s. The imagery indicates that open-water phytoplankton blooms occur first in late April in coastal waters, peak in early May over the middle shelf, and decay rapidly afterwards, reaching concentration minima in June in both regions. These patterns show that the earlier ship observations are valid for most of the eastern Bering shelf. A very tight correlation is found between the PROBES surface chlorophyll a concentrations and mean mixed-layer chlorophyll concentrations. The significant discrepancies between CZCS and ship-based chlorophyll estimates may be due to aliasing in time by the CZCS. It is concluded that neither satellite nor ship alone can do an adequate job of characterizing the physics or biological dynamics of the ocean.

Contact infection of infectious disease onboard a cruise ship.

PubMed

Zhang, Nan; Miao, Ruosong; Huang, Hong; Chan, Emily Y Y

2016-12-08

Cruise tourism has become more popular. Long-term personal contact, complex population flows, a lack of medical care facilities, and defective infrastructure aboard most cruise ships is likely to result in the ship becoming an incubator for infectious diseases. In this paper, we use a cruise ship as a research scenario. Taking into consideration personal behavior, the nature and transfer route of the virus across different surfaces, virus reproduction, and disinfection, we studied contact infection of infectious disease on a cruise ship. Using gastroenteritis caused by the norovirus as an example, we analyzed the characteristics of infectious disease propagation based on simulation results under different conditions. We found hand washing are the most important factors affecting virus propagation and passenger infection. It also decides either the total number of virus microorganisms or the virus distribution in different functional areas. The transfer rate between different surfaces is a key factor influencing the concentricity of the virus. A high transfer rate leads to high concentricity. In addition, the risk of getting infected is effectively reduced when the disinfection frequency is above a certain threshold. The efficiency of disinfection of functional areas is determined by total virus number and total contact times of surfaces.

DNA-based probes for flow cytometry analysis of endocytosis and recycling.

PubMed

Dumont, Claire; Czuba, Ewa; Chen, Moore; Villadangos, Jose A; Johnston, Angus P R; Mintern, Justine D

2017-04-01

The internalization of proteins plays a key role in cell development, cell signaling and immunity. We have previously developed a specific hybridization internalization probe (SHIP) to quantitate the internalization of proteins and particles into cells. Herein, we extend the utility of SHIP to examine both the endocytosis and recycling of surface receptors using flow cytometry. SHIP was used to monitor endocytosis of membrane-bound transferrin receptor (TFR) and its soluble ligand transferrin (TF). SHIP enabled measurements of the proportion of surface molecules internalized, the internalization kinetics and the proportion and rate of internalized molecules that recycle to the cell surface with time. Using this method, we have demonstrated the internalization and recycling of holo-TF and an antibody against the TFR behave differently. This assay therefore highlights the implications of receptor internalization and recycling, where the internalization of the receptor-antibody complex behaves differently to the receptor-ligand complex. In addition, we observe distinct internalization patterns for these molecules expressed by different subpopulations of primary cells. SHIP provides a convenient and high throughput technique for analysis of trafficking parameters for both cell surface receptors and their ligands. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Contact infection of infectious disease onboard a cruise ship

PubMed Central

Zhang, Nan; Miao, Ruosong; Huang, Hong; Chan, Emily Y. Y.

2016-01-01

Cruise tourism has become more popular. Long-term personal contact, complex population flows, a lack of medical care facilities, and defective infrastructure aboard most cruise ships is likely to result in the ship becoming an incubator for infectious diseases. In this paper, we use a cruise ship as a research scenario. Taking into consideration personal behavior, the nature and transfer route of the virus across different surfaces, virus reproduction, and disinfection, we studied contact infection of infectious disease on a cruise ship. Using gastroenteritis caused by the norovirus as an example, we analyzed the characteristics of infectious disease propagation based on simulation results under different conditions. We found hand washing are the most important factors affecting virus propagation and passenger infection. It also decides either the total number of virus microorganisms or the virus distribution in different functional areas. The transfer rate between different surfaces is a key factor influencing the concentricity of the virus. A high transfer rate leads to high concentricity. In addition, the risk of getting infected is effectively reduced when the disinfection frequency is above a certain threshold. The efficiency of disinfection of functional areas is determined by total virus number and total contact times of surfaces. PMID:27929141

Estimation of exhaust emission from ocean-going vessels in Hong Kong.

PubMed

Yau, P S; Lee, S C; Corbett, James J; Wang, Chengfeng; Cheng, Y; Ho, K F

2012-08-01

As one of the busiest port in the world, ship emissions have become of great concern in Hong Kong. In this study, a detailed maritime emission inventory for ocean-going vessels (OGVs) in Hong Kong with the base year of 2007 was developed. The high-resolution vessel speed profiles determined using the Automatic Identification System (AIS) during 2009 were adopted for the speed data in the estimation. It was obtained that the total ship emissions from 37,150 voyages of OGVs in 2007 were 17,097, 8190, and 1035 tonnes accounting for 17%, 11%, and 16% of the total emissions of NO(x), SO(2), and PM(10), respectively. The contribution of ship emissions during transiting was 60-68% for three pollutants while the emissions during hotelling were responsible for the remaining portions. From the emission spatial allocation, the shipping route along the East Lamma Channel and the berthing location of the Kwai Chung and Tsing Yi Container Port comprised the regions with the highest emissions. The OGV emissions in Hong Kong contributed 0.07% NO(x), 0.05% SO(2), and 0.06% PM(10) out of the global total shipping emissions in 2007. Copyright © 2012 Elsevier B.V. All rights reserved.

Ionospheric Bow Wave Induced by the Moon Shadow Ship Over the Continent of United States on 21 August 2017

NASA Astrophysics Data System (ADS)

Sun, Yang-Yi; Liu, Jann-Yenq; Lin, Charles Chien-Hung; Lin, Chi-Yen; Shen, Ming-Hsueh; Chen, Chieh-Hung; Chen, Chia-Hung; Chou, Min-Yang

2018-01-01

A moon shadow of the total solar eclipse swept through the continent of United States (CONUS) from west to east on 21 August 2017. Massive total electron content (integration of electron density from 0 km to 20,200 km altitude) observations from 2,255 ground-based Global Navigation Satellite System receivers show that the moon shadow ship generates a great ionospheric bow wave front which extends 1,500 km away from the totality path covering the entire CONUS. The bow wave front consists of the acoustic shock wave due to the supersonic/near-supersonic moon shadow ship and the significant plasma recombination due to the reduction in solar irradiation within the shadow area. The deep bow wave trough (-0.02 total electron content unit (1 TECU = 1016 el m-2) area) nearly coincides with the 100% obscuration moving along the totality path over the CONUS through the entire eclipse period. The supersonic moon shadow ship induces a bow wave crest in front of the ship ( 80% obscuration). It is the first time to find the acoustic shock wave-formed bow wave trough and crest near the totality.

Contact infection of infectious disease onboard a cruise ship

NASA Astrophysics Data System (ADS)

Zhang, Nan; Miao, Ruosong; Huang, Hong; Chan, Emily Y. Y.

2016-12-01

Cruise tourism has become more popular. Long-term personal contact, complex population flows, a lack of medical care facilities, and defective infrastructure aboard most cruise ships is likely to result in the ship becoming an incubator for infectious diseases. In this paper, we use a cruise ship as a research scenario. Taking into consideration personal behavior, the nature and transfer route of the virus across different surfaces, virus reproduction, and disinfection, we studied contact infection of infectious disease on a cruise ship. Using gastroenteritis caused by the norovirus as an example, we analyzed the characteristics of infectious disease propagation based on simulation results under different conditions. We found hand washing are the most important factors affecting virus propagation and passenger infection. It also decides either the total number of virus microorganisms or the virus distribution in different functional areas. The transfer rate between different surfaces is a key factor influencing the concentricity of the virus. A high transfer rate leads to high concentricity. In addition, the risk of getting infected is effectively reduced when the disinfection frequency is above a certain threshold. The efficiency of disinfection of functional areas is determined by total virus number and total contact times of surfaces.

SENTINEL-1/2 Data for Ship Traffic Monitoring on the Danube River

NASA Astrophysics Data System (ADS)

Negula, I. Dana; Poenaru, V. D.; Olteanu, V. G.; Badea, A.

2016-06-01

After a long period of drought, the water level of the Danube River has significantly dropped especially on the Romanian sector, in July-August 2015. Danube reached the lowest water level recorded in the last 12 years, causing the blockage of the ships in the sector located close to Zimnicea Harbour. The rising sand banks in the navigable channel congested the commercial traffic for a few days with more than 100 ships involved. The monitoring of the decreasing water level and the traffic jam was performed based on Sentinel-1 and Sentinel-2 free data provided by the European Space Agency and the European Commission within the Copernicus Programme. Specific processing methods (calibration, speckle filtering, geocoding, change detection, image classification, principal component analysis, etc.) were applied in order to generate useful products that the responsible authorities could benefit from. The Sentinel data yielded good results for water mask extraction and ships detection. The analysis continued after the closure of the crisis situation when the water reached the nominal level again. The results indicate that Sentinel data can be successfully used for ship traffic monitoring, building the foundation of future endeavours for a durable monitoring of the Danube River.

Rebuilding the NAVSEA Early Stage Ship Design Environment

DTIC Science & Technology

2010-04-01

rules -of- thumb to base these crucial decisions upon. With High Performance Computing (HPC) as an enabler, the vision is to explore all downstream...the results of the analysis back into LEAPS. Another software development worthy of discussion here is Intelligent Ship Arrangements ( ISA ), which...constraints and rules set by the users ahead of time. When used in a systematic and stochastic way, and when integrated using LEAPS, having this

Radiation Dose Assessments for Fleet-Based Individuals in Operation Tomodachi

DTIC Science & Technology

2013-09-01

area. DOD took actions to ensure that radioactively contaminated food and bottled water did not reach the DOD-affiliated population. Military commands...material from contaminated surfaces of ships or aircraft or in water, food , or soil and dust each day while on shore. These doses were calculated for...22 2.4.4. Exposure related to Surface Contamination on Ships.......................... 22 2.4.5. Exposure from Skin Contamination

Radiation Dose Assessments for Fleet-Based Individuals in Operation Tomodachi, Revision 1

DTIC Science & Technology

2014-04-01

U.S. agencies were also deployed to the area. DOD took actions to ensure that radioactively contaminated food and bottled water did not reach the...material from contaminated surfaces of ships or aircraft or in water, food , or soil and dust each day while on shore. These doses were calculated for...Exposure below Deck on Ships .......................................................... 22 2.4.4. Exposure related to Radioactive Surface Contamination

Improving Visual Survey Capabilities for Marine Mammal Studies

DTIC Science & Technology

2014-09-30

presence of air- breathing mammals, and they can be conducted from ships, aircraft, or land . For ship- and land -based surveys, powerful, pedestal-mounted...part of the ONR-and NRL-funded Air- Sea Interactions in the Northern Indian Ocean Regional Initiative (ASIRI) program, a physical oceanographic...research effort to study upper ocean processes and air- sea interactions that regulate the Asian monsoons. We will use the DURIP-funded big-eye

Costs and benefits of low-sulphur fuel standard for Baltic Sea shipping.

PubMed

Antturi, Jim; Hänninen, Otto; Jalkanen, Jukka-Pekka; Johansson, Lasse; Prank, Marje; Sofiev, Mikhail; Ollikainen, Markku

2016-12-15

The maximum allowable fuel sulphur content for shipping in the Baltic Sea dropped from 1%S to 0.1%S in 1 January 2015. We provide a cost-benefit analysis of the sulphur reduction policy in the Baltic Sea Sulphur Emission Control Area (SECA). We calculated the abatement costs based on shipowners' optimal decision-making in choosing between low-sulphur fuel and a sulphur scrubber, and the benefits were modelled through a high-resolution impact pathway analysis, which took into account the formation and dispersion of the emissions, and considered the positive health impacts resulting from lowered ambient PM 2.5 concentrations. Our basic result indicates that for the Baltic Sea only, the latest sulphur regulation is not cost-effective. The expected annual cost is roughly €465 M and benefit 2200 saved Disability Adjusted Life-Years (DALYs) or monetized €105 M. Based on our sensitivity analysis, the benefits yet have a potential to exceed the costs. The analysis neither takes into account the acidifying impact of sulphur nor the impact North Sea shipping has on the cost-benefit ratio. Lastly, a similar approach is found highly recommendable to study the implications of the upcoming Tier III NO x standard for shipping. Copyright © 2016 Elsevier Ltd. All rights reserved.

Multiple-Parameter, Low-False-Alarm Fire-Detection Systems

NASA Technical Reports Server (NTRS)

Hunter, Gary W.; Greensburg, Paul; McKnight, Robert; Xu, Jennifer C.; Liu, C. C.; Dutta, Prabir; Makel, Darby; Blake, D.; Sue-Antillio, Jill

2007-01-01

Fire-detection systems incorporating multiple sensors that measure multiple parameters are being developed for use in storage depots, cargo bays of ships and aircraft, and other locations not amenable to frequent, direct visual inspection. These systems are intended to improve upon conventional smoke detectors, now used in such locations, that reliably detect fires but also frequently generate false alarms: for example, conventional smoke detectors based on the blockage of light by smoke particles are also affected by dust particles and water droplets and, thus, are often susceptible to false alarms. In contrast, by utilizing multiple parameters associated with fires, i.e. not only obscuration by smoke particles but also concentrations of multiple chemical species that are commonly generated in combustion, false alarms can be significantly decreased while still detecting fires as reliably as older smoke-detector systems do. The present development includes fabrication of sensors that have, variously, micrometer- or nanometer-sized features so that such multiple sensors can be integrated into arrays that have sizes, weights, and power demands smaller than those of older macroscopic sensors. The sensors include resistors, electrochemical cells, and Schottky diodes that exhibit different sensitivities to the various airborne chemicals of interest. In a system of this type, the sensor readings are digitized and processed by advanced signal-processing hardware and software to extract such chemical indications of fires as abnormally high concentrations of CO and CO2, possibly in combination with H2 and/or hydrocarbons. The system also includes a microelectromechanical systems (MEMS)-based particle detector and classifier device to increase the reliability of measurements of chemical species and particulates. In parallel research, software for modeling the evolution of a fire within an aircraft cargo bay has been developed. The model implemented in the software can describe the concentrations of chemical species and of particulate matter as functions of time. A system of the present developmental type and a conventional fire detector were tested under both fire and false-alarm conditions in a Federal Aviation Administration cargo-compartment- testing facility. Both systems consistently detected fires. However, the conventional fire detector consistently generated false alarms, whereas the developmental system did not generate any false alarms.

Advanced Ship Detection For Spaceborne Based Maritime Awareness

NASA Astrophysics Data System (ADS)

Radius, Andrea; Ferreira, Joao; Carmo, Paulo; Marques, Paulo

2013-12-01

In the last years the increase in marine traffic generated the necessity of global monitoring for marine environment management in terms of safety, security and fisheries. The increasing number of new satellite-based Synthetic Aperture Radar (SAR) systems, and the intrinsic capability of the transmitted electromagnetic pulses to interact with the ships and to retrieve its cinematic characteristics, made this instrument particularly fit to improve global maritime awareness through the fusion with cooperative data (AIS, VMS, LRIT). The growing need of global maritime awareness gave a push to the realization of different projects in the European context, each one focused on a different particular objective. Particularly useful is the synergy between the operational and research aspects, being the goal of the last to improve the state of the art in the field of ship detection. Two European projects are the key to strive this synergy: the project MARitime Security Service (MARISS), which implements the operational capability, and the R&D Dolphin projects, which is focused on the deep exploitation of remote sensing data and on the technological development of advanced techniques for ship detection and classification purposes, and Seabilla project, which is also dedicated to improve the current ship detection capability and to fuse all the available information from different data sources for border surveillance optimization. This paper introduces the multipurpose Edisoft Vessel Detection software (EdiVDC) implemented by the EDISOFT company, which comes from the necessity to respect increasingly stringent requirements in terms of ship detection. The EdiVDC software is being operationally used in the framework of the MARISS project and it integrates advanced processing algorithms, developed in the scope of the Dolphin project with the cooperation of ISEL-IT (Instituto de Telecomunicações), and data simulators, developed in the context of the Seabilla project, improving the software capability and introducing new functionalities. In this work we present the functionalities of the software and the main results achieved with different types of SAR data.