Evolved Minimal Frustration in Multifunctional Biomolecules.

PubMed

Röder, Konstantin; Wales, David J

2018-05-25

Protein folding is often viewed in terms of a funnelled potential or free energy landscape. A variety of experiments now indicate the existence of multifunnel landscapes, associated with multifunctional biomolecules. Here, we present evidence that these systems have evolved to exhibit the minimal number of funnels required to fulfil their cellular functions, suggesting an extension to the principle of minimum frustration. We find that minimal disruptive mutations result in additional funnels, and the associated structural ensembles become more diverse. The same trends are observed in an atomic cluster. These observations suggest guidelines for rational design of engineered multifunctional biomolecules.

Application of higher harmonic blade feathering for helicopter vibration reduction

NASA Technical Reports Server (NTRS)

Powers, R. W.

1978-01-01

Higher harmonic blade feathering for helicopter vibration reduction is considered. Recent wind tunnel tests confirmed the effectiveness of higher harmonic control in reducing articulated rotor vibratory hub loads. Several predictive analyses developed in support of the NASA program were shown to be capable of calculating single harmonic control inputs required to minimize a single 4P hub response. In addition, a multiple-input, multiple-output harmonic control predictive analysis was developed. All techniques developed thus far obtain a solution by extracting empirical transfer functions from sampled data. Algorithm data sampling and processing requirements are minimal to encourage adaptive control system application of such techniques in a flight environment.

Developing locally sourced brine additive for anti-icing.

DOT National Transportation Integrated Search

2014-08-01

The objective of this project was to develop a series of anti-icers tailored to meet the varying requirements of highway anti-icing performance, : cost-effectiveness, and minimized corrosion and environmental impact for typical road weather scenarios...

Electromyographic monitoring and its anatomical implications in minimally invasive spine surgery.

PubMed

Uribe, Juan S; Vale, Fernando L; Dakwar, Elias

2010-12-15

Literature review. The objective of this article is to examine current intraoperative electromyography (EMG) neurophysiologic monitoring methods and their application in minimally invasive techniques. We will also discuss the recent application of EMG and its anatomic implications to the minimally invasive lateral transpsoas approach to the spine. Minimally invasive techniques require that the same goals of surgery be achieved, with the hope of decreased morbidity to the patient. Unlike standard open procedures, direct visualization of the anatomy is decreased. To increase the safety of minimally invasive spine surgery, neurophysiological monitoring techniques have been developed. Review of the literature was performed using the National Center for Biotechnology Information databases using PUBMED/MEDLINE. All articles in the English language discussing the use of intraoperative EMG monitoring and minimally invasive spine surgery were reviewed. The role of EMG monitoring in special reference to the minimally invasive lateral transpsoas approach is also described. In total, 76 articles were identified that discussed the role of neuromonitoring in spine surgery. The majority of articles on EMG and spine surgery discuss the use of intraoperative neurophysiological monitoring (IOM) for safe and accurate pedicle screw placement. In general, there is a paucity of literature that pertains to intraoperative EMG neuromonitoring and minimally invasive spine surgery. Recently, EMG has been used during minimally invasive lateral transpsoas approach to the lumbar spine for interbody fusion. The addition of EMG to the lateral approach has contributed to decrease the complication rate from 30% to less than 1%. In minimally invasive approaches to the spine, the use of EMG IOM might provide additional safety, such as percutaneous pedicle screw placement, where visualization is limited compared with conventional open procedures. In addition to knowledge of the anatomy and image guidance, directional EMG IOM is crucial for safe passage through the psoas muscle during the minimally invasive lateral retroperitoneal approach.

Waste reduction plan for The Oak Ridge National Laboratory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schultz, R.M.

1990-04-01

The Oak Ridge National Laboratory (ORNL) is a multipurpose Research and Development (R D) facility. These R D activities generate numerous small waste streams. Waste minimization is defined as any action that minimizes the volume or toxicity of waste by avoiding its generation or recycling. This is accomplished by material substitution, changes to processes, or recycling wastes for reuse. Waste reduction is defined as waste minimization plus treatment which results in volume or toxicity reduction. The ORNL Waste Reduction Program will include both waste minimization and waste reduction efforts. Federal regulations, DOE policies and guidelines, increased costs and liabilities associatedmore » with the management of wastes, limited disposal options and facility capacities, and public consciousness have been motivating factors for implementing comprehensive waste reduction programs. DOE Order 5820.2A, Section 3.c.2.4 requires DOE facilities to establish an auditable waste reduction program for all LLW generators. In addition, it further states that any new facilities, or changes to existing facilities, incorporate waste minimization into design considerations. A more recent DOE Order, 3400.1, Section 4.b, requires the preparation of a waste reduction program plan which must be reviewed annually and updated every three years. Implementation of a waste minimization program for hazardous and radioactive mixed wastes is sited in DOE Order 5400.3, Section 7.d.5. This document has been prepared to address these requirements. 6 refs., 1 fig., 2 tabs.« less

Flame Retardancy of Chemically Modified Lignin as Functional Additive to Epoxy Nanocomposites

Treesearch

John A. Howarter; Gamini P. Mendis; Alex N. Bruce; Jeffrey P. Youngblood; Mark A. Dietenberger; Laura Hasburgh

2015-01-01

Epoxy printed circuit boards are used in a variety of electronics applications as rigid, thermally stable substrates. Due to the propensity of components on the boards, such as batteries and interconnects, to fail and ignite the epoxy, flame retardant additives are required to minimize fire risk. Currently, industry uses brominated flame retardants, such as TBBPA, to...

Composite Materials for Structural Design.

DTIC Science & Technology

1982-03-01

location of failure initiation. Accurate results for the third require additional considerations not treated here. 49 ABSTRACT Tranverse Shear Deformation...mentioned competing effects so as to minimize the residual thermal stress at the termination of the cool-down phase. Elastic Analysis Consider a symmetric

Energy conservation through sealing technology

NASA Technical Reports Server (NTRS)

Stair, W. K.; Ludwig, L. P.

1978-01-01

Improvements in fluid film sealing resulting from a proposed research program could lead to an annual energy saving, on a national basis, equivalent to about 37 million bbl of oil or 0.3% of the total U.S. energy consumption. Further, the application of known sealing technology can result in an annual saving of an additional 10 million bbl of oil. The energy saving would be accomplished by reduction in process heat energy loss, reduction of frictional energy generated, and minimization of energy required to operate ancillary equipment associated with the seal system. In addition to energy saving, cost effectiveness is further enhanced by reduction in maintenance and in minimization of equipment for collecting leakage and for meeting environmental pollution standards.

Immobilization techniques to avoid enzyme loss from oxidase-based biosensors: a one-year study.

PubMed

House, Jody L; Anderson, Ellen M; Ward, W Kenneth

2007-01-01

Continuous amperometric sensors that measure glucose or lactate require a stable sensitivity, and glutaraldehyde crosslinking has been used widely to avoid enzyme loss. Nonetheless, little data is published on the effectiveness of enzyme immobilization with glutaraldehyde. A combination of electrochemical testing and spectrophotometric assays was used to study the relationship between enzyme shedding and the fabrication procedure. In addition, we studied the relationship between the glutaraldehyde concentration and sensor performance over a period of one year. The enzyme immobilization process by glutaraldehyde crosslinking to glucose oxidase appears to require at least 24-hours at room temperature to reach completion. In addition, excess free glucose oxidase can be removed by soaking sensors in purified water for 20 minutes. Even with the addition of these steps, however, it appears that there is some free glucose oxidase entrapped within the enzyme layer which contributes to a decline in sensitivity over time. Although it reduces the ultimate sensitivity (probably via a change in the enzyme's natural conformation), glutaraldehyde concentration in the enzyme layer can be increased in order to minimize this instability. After exposure of oxidase enzymes to glutaraldehyde, effective crosslinking requires a rinse step and a 24-hour incubation step. In order to minimize the loss of sensor sensitivity over time, the glutaraldehyde concentration can be increased.

Influence of linear profile modification and loading conditions on the dynamic tooth load and stress of high contact ratio gears

NASA Technical Reports Server (NTRS)

Lee, Chinwai; Lin, Hsiang Hsi; Oswald, Fred B.; Townsend, Dennis P.

1990-01-01

A computer simulation for the dynamic response of high-contact-ratio spur gear transmissions is presented. High contact ratio gears have the potential to produce lower dynamic tooth loads and minimum root stress but they can be sensitive to tooth profile errors. The analysis presented examines various profile modifications under realistic loading conditions. The effect of these modifications on the dynamic load (force) between mating gear teeth and the dynamic root stress is presented. Since the contact stress is dependent on the dynamic load, minimizing dynamic loads will also minimize contact stresses. It is shown that the combination of profile modification and the applied load (torque) carried by a gear system has a significant influence on gear dynamics. The ideal modification at one value of applied load will not be the best solution for a different load. High-contact-ratio gears were found to require less modification than standard low-contact-ratio gears. High-contact-ratio gears are more adversely affected by excess modification than by under modification. In addition, the optimal profile modification required to minimize the dynamic load (hence the contact stress) on a gear tooth differs from the optimal modification required to minimize the dynamic root (bending) stress. Computer simulation can help find the design tradeoffs to determine the best profile modification to satisfy the conflicting constraints of minimizing both the load and root stress in gears which must operate over a range of applied loads.

Evaluating the use of preoperative antibiotics in pediatric orthopaedic surgery.

PubMed

Formaini, Nathan; Jacob, Paul; Willis, Leisel; Kean, John R

2012-01-01

To evaluate the rate of infection after minimally invasive procedures on a consecutive series of pediatric orthopaedic patients. We hypothesized that the use of preoperative antibiotics for minimally invasive pediatric orthopaedic procedures does not significantly reduce the incidence of surgical site infection requiring surgical debridement within 30 days of the primary procedure. We retrospectively reviewed 2330 patients having undergone minimally invasive orthopaedic procedures at our institution between March 2008 and November 2010. Knee arthroscopy, closed reduction with percutaneous fixation, soft tissue releases, excision of bony or soft-tissue masses, and removal of hardware constituted the vast majority of included procedures. Two groups, based on whether prophylactic antibiotics were administered before surgery, were created and the incidence of a repeat procedure required for deep infection was recorded. Statistical analysis was performed to determine significance, if any, between the 2 groups. Chart review of the 2330 patients identified 1087 as having received preoperative antibiotics, whereas the remaining 1243 patients did not receive antibiotics before surgery. Only 1 patient out of the 1243 cases in which antibiotics were not given required additional surgery within 30 days of the primary procedure due to a complicated surgical site infection (an incidence of 0.0008%). No patients in the antibiotic group developed a postoperative infection within 30 days requiring a return to the operating room for management. Our data revealed no significant increase in the incidence of complicated infection requiring additional procedures when antibiotics were not administered before surgery. Though prophylactic antibiotics have been shown to confer numerous benefits for patients undergoing relatively major operations, their use in cases of minimally invasive and/or percutaneous orthopaedic surgery is not well defined. Our data suggest that the use of prophylactic antibiotics may not be indicated for many less invasive procedures when performed in a low-risk pediatric population. Future studies are warranted to help establish evidence-based guidelines regarding the routine use of prophylactic antibiotics in this specific population, hopefully resulting in improved cost-effectiveness and safety while slowing the emergence of new drug-resistant organisms. Level III, retrospective comparative.

Thoracoscopic management of empyema thoracis

PubMed Central

Wait, Michael A; Beckles, Daniel L; Paul, Michelle; Hotze, Margaret; DiMaio, Michael J

2007-01-01

Appropriate management of empyema thoracis is dependent upon a secure diagnosis of the etiology of empyema and the phase of development. Minimal access surgery using video-assisted thoracoscopy (VATS) is one of many useful techniques in treating empyema. Complex empyema requires adjunctive treatment in addition to VATS. PMID:19789675

Major design issues of molten carbonate fuel cell power generation unit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, T.P.

1996-04-01

In addition to the stack, a fuel cell power generation unit requires fuel desulfurization and reforming, fuel and oxidant preheating, process heat removal, waste heat recovery, steam generation, oxidant supply, power conditioning, water supply and treatment, purge gas supply, instrument air supply, and system control. These support facilities add considerable cost and system complexity. Bechtel, as a system integrator of M-C Power`s molten carbonate fuel cell development team, has spent substantial effort to simplify and minimize these supporting facilities to meet cost and reliability goals for commercialization. Similiar to other fuels cells, MCFC faces design challenge of how to complymore » with codes and standards, achieve high efficiency and part load performance, and meanwhile minimize utility requirements, weight, plot area, and cost. However, MCFC has several unique design issues due to its high operating temperature, use of molten electrolyte, and the requirement of CO2 recycle.« less

Immobilization Techniques to Avoid Enzyme Loss from Oxidase-Based Biosensors: A One-Year Study

PubMed Central

House, Jody L.; Anderson, Ellen M.; Ward, W. Kenneth

2007-01-01

Background Continuous amperometric sensors that measure glucose or lactate require a stable sensitivity, and glutaraldehyde crosslinking has been used widely to avoid enzyme loss. Nonetheless, little data is published on the effectiveness of enzyme immobilization with glutaraldehyde. Methods A combination of electrochemical testing and spectrophotometric assays was used to study the relationship between enzyme shedding and the fabrication procedure. In addition, we studied the relationship between the glutaraldehyde concentration and sensor performance over a period of one year. Results The enzyme immobilization process by glutaraldehyde crosslinking to glucose oxidase appears to require at least 24-hours at room temperature to reach completion. In addition, excess free glucose oxidase can be removed by soaking sensors in purified water for 20 minutes. Even with the addition of these steps, however, it appears that there is some free glucose oxidase entrapped within the enzyme layer which contributes to a decline in sensitivity over time. Although it reduces the ultimate sensitivity (probably via a change in the enzyme's natural conformation), glutaraldehyde concentration in the enzyme layer can be increased in order to minimize this instability. Conclusions After exposure of oxidase enzymes to glutaraldehyde, effective crosslinking requires a rinse step and a 24-hour incubation step. In order to minimize the loss of sensor sensitivity over time, the glutaraldehyde concentration can be increased. PMID:19888375

Improving the environmental and performance characteristics of vehicles by introducing the surfactant additive into gasoline.

PubMed

Magaril, Elena; Magaril, Romen

2016-09-01

The operation of modern vehicles requires the introduction of package of fuel additives to ensure the required level of operating characteristics, some of which cannot be achieved by current oil refining methods. The use of additives allows flexibility of impact on the properties of the fuel at minimal cost, increasing the efficiency and environmental safety of vehicles. Among the wide assortment of additives available on the world market, many are surfactants. It has been shown that the introduction of some surfactants into gasoline concurrently reduces losses from gasoline evaporation, improves the mixture formation during injection of gasoline into the engine and improves detergent and anticorrosive properties. The surfactant gasoline additive that provides significant improvement in the quality of gasoline used and environmental and operating characteristics of vehicles has been developed and thoroughly investigated. The results of studies confirming the efficiency of the gasoline additive application are herein presented.

Comprehensive Training Curricula for Minimally Invasive Surgery

PubMed Central

Palter, Vanessa N

2011-01-01

Background The unique skill set required for minimally invasive surgery has in part contributed to a certain portion of surgical residency training transitioning from the operating room to the surgical skills laboratory. Simulation lends itself well as a method to shorten the learning curve for minimally invasive surgery by allowing trainees to practice the unique motor skills required for this type of surgery in a safe, structured environment. Although a significant amount of important work has been done to validate simulators as viable systems for teaching technical skills outside the operating room, the next step is to integrate simulation training into a comprehensive curriculum. Objectives This narrative review aims to synthesize the evidence and educational theories underlining curricula development for technical skills both in a broad context and specifically as it pertains to minimally invasive surgery. Findings The review highlights the critical aspects of simulation training, such as the effective provision of feedback, deliberate practice, training to proficiency, the opportunity to practice at varying levels of difficulty, and the inclusion of both cognitive teaching and hands-on training. In addition, frameworks for integrating simulation training into a comprehensive curriculum are described. Finally, existing curricula on both laparoscopic box trainers and virtual reality simulators are critically evaluated. PMID:22942951

Environmental Symposium Held in Crystal City, Virginia on May 5-6, 1992

DTIC Science & Technology

1992-05-01

addition, the Act creat a new program designed to prevent sudden, accidental releases of extremely hazardo substances . Generally, the Act sets forth a... prevent of sudden, The owner or operator of any facility handling an extremely hazardous substance will also be required to prepare and implement a risk...management plan to detect and prevent or minimize the potential for an accidental release of extremely hazardous substances . EPA may require that such

The Use of Wetting Agents/Fume Suppressants for Minimizing the Atmospheric Emissions from Hard Chromium Electroplating Baths

DTIC Science & Technology

2004-03-01

oxidized rapidly producing trivalent chromium and insoluble organic compounds that eventually decomposed to carbon dioxide. This behavior required...frequent or continuous WA/FS additions, making them a more temporary than permanent solution. The trivalent chromium was also a bath contaminant requiring...need for hard chromium electroplating, but is not expected to ever be able to eliminate it. • Trivalent Chromium Electroplating: Chromium can be

The Minimal Preprocessing Pipelines for the Human Connectome Project

PubMed Central

Glasser, Matthew F.; Sotiropoulos, Stamatios N; Wilson, J Anthony; Coalson, Timothy S; Fischl, Bruce; Andersson, Jesper L; Xu, Junqian; Jbabdi, Saad; Webster, Matthew; Polimeni, Jonathan R; Van Essen, David C; Jenkinson, Mark

2013-01-01

The Human Connectome Project (HCP) faces the challenging task of bringing multiple magnetic resonance imaging (MRI) modalities together in a common automated preprocessing framework across a large cohort of subjects. The MRI data acquired by the HCP differ in many ways from data acquired on conventional 3 Tesla scanners and often require newly developed preprocessing methods. We describe the minimal preprocessing pipelines for structural, functional, and diffusion MRI that were developed by the HCP to accomplish many low level tasks, including spatial artifact/distortion removal, surface generation, cross-modal registration, and alignment to standard space. These pipelines are specially designed to capitalize on the high quality data offered by the HCP. The final standard space makes use of a recently introduced CIFTI file format and the associated grayordinates spatial coordinate system. This allows for combined cortical surface and subcortical volume analyses while reducing the storage and processing requirements for high spatial and temporal resolution data. Here, we provide the minimum image acquisition requirements for the HCP minimal preprocessing pipelines and additional advice for investigators interested in replicating the HCP’s acquisition protocols or using these pipelines. Finally, we discuss some potential future improvements for the pipelines. PMID:23668970

Novel physical constraints on implementation of computational processes

NASA Astrophysics Data System (ADS)

Wolpert, David; Kolchinsky, Artemy

Non-equilibrium statistical physics permits us to analyze computational processes, i.e., ways to drive a physical system such that its coarse-grained dynamics implements some desired map. It is now known how to implement any such desired computation without dissipating work, and what the minimal (dissipationless) work is that such a computation will require (the so-called generalized Landauer bound\\x9D). We consider how these analyses change if we impose realistic constraints on the computational process. First, we analyze how many degrees of freedom of the system must be controlled, in addition to the ones specifying the information-bearing degrees of freedom, in order to avoid dissipating work during a given computation, when local detailed balance holds. We analyze this issue for deterministic computations, deriving a state-space vs. speed trade-off, and use our results to motivate a measure of the complexity of a computation. Second, we consider computations that are implemented with logic circuits, in which only a small numbers of degrees of freedom are coupled at a time. We show that the way a computation is implemented using circuits affects its minimal work requirements, and relate these minimal work requirements to information-theoretic measures of complexity.

Chronic subdural haematoma treated by craniotomy, durectomy, outer membranectomy and subgaleal suction drainage. Personal experience in 39 patients.

PubMed

Mohamed, E E H Hussein

2003-06-01

According to the CT and MRI appearances, 39 chronic subdural haematoma (CSDH) patients were suspected of having solid clots and/or a high likelihood of loculation. Craniotomy was planned from the start. Beside the better exposure, excision of the dura and outer membrane, assumed to be the source of haematoma fluid, this is an additional step to minimize the incidence of significant recollection. There were no additional operative or postoperative cranial and/or systemic complications when compared with other minor procedures. Two patients (5%) required once percutaneous tapping and aspiration. Accordingly, if a case is considered to be better managed with craniotomy, durectomy and outer membranectomy this is an easy and safe technique with minimal incidence of recollection, morbidity and mortality.

Evidence for surprise minimization over value maximization in choice behavior

PubMed Central

Schwartenbeck, Philipp; FitzGerald, Thomas H. B.; Mathys, Christoph; Dolan, Ray; Kronbichler, Martin; Friston, Karl

2015-01-01

Classical economic models are predicated on the idea that the ultimate aim of choice is to maximize utility or reward. In contrast, an alternative perspective highlights the fact that adaptive behavior requires agents’ to model their environment and minimize surprise about the states they frequent. We propose that choice behavior can be more accurately accounted for by surprise minimization compared to reward or utility maximization alone. Minimizing surprise makes a prediction at variance with expected utility models; namely, that in addition to attaining valuable states, agents attempt to maximize the entropy over outcomes and thus ‘keep their options open’. We tested this prediction using a simple binary choice paradigm and show that human decision-making is better explained by surprise minimization compared to utility maximization. Furthermore, we replicated this entropy-seeking behavior in a control task with no explicit utilities. These findings highlight a limitation of purely economic motivations in explaining choice behavior and instead emphasize the importance of belief-based motivations. PMID:26564686

Identifying Minimal Changes in Nonerosive Reflux Disease: Is the Pay Worth the Labor?

PubMed

Gabbard, Scott L; Fass, Ronnie; Maradey-Romero, Carla; Gingold Belfer, Rachel; Dickman, Ram

2016-01-01

Gastroesophageal reflux disease has a variable presentation on upper endoscopy. Gastroesophageal reflux disease can be divided into 3 endoscopic categories: Barrett's esophagus, erosive esophagitis, and normal mucosa/nonerosive reflux disease (NERD). Each of these phenotypes behave in a distinct manner, in regards to symptom response to treatment, and risk of development of complications such as esophageal adenocarcinoma. Recently, it has been proposed to further differentiate NERD into 2 categories: those with and those without "minimal changes." These minimal changes include endoscopic abnormalities, such as villous mucosal surface, mucosal islands, microerosions, and increased vascularity at the squamocolumnar junction. Although some studies have shown that patients with minimal changes may have higher rates of esophageal acid exposure compared with those without minimal changes, it is currently unclear if these patients behave differently than those currently categorized as having NERD. The clinical utility of identifying these lesions should be weighed against the cost of the requisite equipment and the additional time required for diagnosis, compared with conventional white light endoscopy.

Minimally invasive surgery of the anterior skull base: transorbital approaches

PubMed Central

Gassner, Holger G.; Schwan, Franziska; Schebesch, Karl-Michael

2016-01-01

Minimally invasive approaches are becoming increasingly popular to access the anterior skull base. With interdisciplinary cooperation, in particular endonasal endoscopic approaches have seen an impressive expansion of indications over the past decades. The more recently described transorbital approaches represent minimally invasive alternatives with a differing spectrum of access corridors. The purpose of the present paper is to discuss transorbital approaches to the anterior skull base in the light of the current literature. The transorbital approaches allow excellent exposure of areas that are difficult to reach like the anterior and posterior wall of the frontal sinus; working angles may be more favorable and the paranasal sinus system can be preserved while exposing the skull base. Because of their minimal morbidity and the cosmetically excellent results, the transorbital approaches represent an important addition to established endonasal endoscopic and open approaches to the anterior skull base. Their execution requires an interdisciplinary team approach. PMID:27453759

76 FR 79141 - List of Rules To Be Reviewed Pursuant to the Regulatory Flexibility Act

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-21

... initial notice within a reasonable time after establishing a customer relationship in two additional..., requires an agency to review its rules that have a significant economic impact upon a substantial number of... be amended or rescinded * * * to minimize any significant economic impact of the rules upon a...

Suspended few-layer graphene beam electromechanical switch with abrupt on-off characteristics and minimal leakage current

NASA Astrophysics Data System (ADS)

Kim, Sung Min; Song, Emil B.; Lee, Sejoon; Seo, Sunae; Seo, David H.; Hwang, Yongha; Candler, R.; Wang, Kang L.

2011-07-01

Suspended few-layer graphene beam electro-mechanical switches (SGSs) with 0.15 μm air-gap are fabricated and electrically characterized. The SGS shows an abrupt on/off current characteristics with minimal off current. In conjunction with the narrow air-gap, the outstanding mechanical properties of graphene enable the mechanical switch to operate at a very low pull-in voltage (VPI) of 1.85 V, which is compatible with conventional complimentary metal-oxide-semiconductor (CMOS) circuit requirements. In addition, we show that the pull-in voltage exhibits an inverse dependence on the beam length.

DNASynth: a software application to optimization of artificial gene synthesis

NASA Astrophysics Data System (ADS)

Muczyński, Jan; Nowak, Robert M.

2017-08-01

DNASynth is a client-server software application in which the client runs in a web browser. The aim of this program is to support and optimize process of artificial gene synthesizing using Ligase Chain Reaction. Thanks to LCR it is possible to obtain DNA strand coding defined by user peptide. The DNA sequence is calculated by optimization algorithm that consider optimal codon usage, minimal energy of secondary structures and minimal number of required LCR. Additionally absence of sequences characteristic for defined by user set of restriction enzymes is guaranteed. The presented software was tested on synthetic and real data.

The Mouse Forced Swim Test

PubMed Central

Can, Adem; Dao, David T.; Arad, Michal; Terrillion, Chantelle E.; Piantadosi, Sean C.; Gould, Todd D.

2012-01-01

The forced swim test is a rodent behavioral test used for evaluation of antidepressant drugs, antidepressant efficacy of new compounds, and experimental manipulations that are aimed at rendering or preventing depressive-like states. Mice are placed in an inescapable transparent tank that is filled with water and their escape related mobility behavior is measured. The forced swim test is straightforward to conduct reliably and it requires minimal specialized equipment. Successful implementation of the forced swim test requires adherence to certain procedural details and minimization of unwarranted stress to the mice. In the protocol description and the accompanying video, we explain how to conduct the mouse version of this test with emphasis on potential pitfalls that may be detrimental to interpretation of results and how to avoid them. Additionally, we explain how the behaviors manifested in the test are assessed. PMID:22314943

Charliecloud: Unprivileged containers for user-defined software stacks in HPC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Priedhorsky, Reid; Randles, Timothy C.

Supercomputing centers are seeing increasing demand for user-defined software stacks (UDSS), instead of or in addition to the stack provided by the center. These UDSS support user needs such as complex dependencies or build requirements, externally required configurations, portability, and consistency. The challenge for centers is to provide these services in a usable manner while minimizing the risks: security, support burden, missing functionality, and performance. We present Charliecloud, which uses the Linux user and mount namespaces to run industry-standard Docker containers with no privileged operations or daemons on center resources. Our simple approach avoids most security risks while maintaining accessmore » to the performance and functionality already on offer, doing so in less than 500 lines of code. Charliecloud promises to bring an industry-standard UDSS user workflow to existing, minimally altered HPC resources.« less

Iodine addition using triiodide solutions

NASA Technical Reports Server (NTRS)

Rutz, Jeffrey A.; Muckle, Susan V.; Sauer, Richard L.

1992-01-01

The study develops: a triiodide solution for use in preparing ground service equipment (GSE) water for Shuttle support, an iodine dissolution method that is reliable and requires minimal time and effort to prepare, and an iodine dissolution agent with a minimal concentration of sodium salt. Sodium iodide and hydriodic acid were both found to dissolve iodine to attain the desired GSE iodine concentrations of 7.5 +/- 2.5 mg/L and 25 +/- 5 mg/L. The 1.75:1 and 2:1 sodium iodide solutions produced higher iodine recoveries than the 1.2:1 hydriodic acid solution. A two-hour preparation time is required for the three sodium iodide solutions. The 1.2:1 hydriodic acid solution can be prepared in less than 5 min. Two sodium iodide stock solutions (2.5:1 and 2:1) were found to dissolve iodine without undergoing precipitation.

Generic waste management requirements for a controlled ecological life support system /CELSS/

NASA Technical Reports Server (NTRS)

Hoshizaki, T.; Hansen, B. D., III

1981-01-01

Regenerative life support systems for future space missions will require closure of the waste-food loop. Each mission application will generate specific requirements for the waste management system. However, there are generic input and output requirements that can be identified when a probable scenario is chosen. This paper discusses the generic requirements when higher plants are chosen as the primary food source. Attention is focused on the quality and quantity of nutrients necessary for culturing higher plants. The types of wastes to be processed are also discussed. In addition, requirements generated by growing plants on three different substrates are presented. This work suggests that the mineral composition of waste materials may require minimal adjustment to satisfy the plant requirements.

Necrotizing pancreatitis: new definitions and a new era in surgical management.

PubMed

Rosenberg, Andrew; Steensma, Elizabeth A; Napolitano, Lena M

2015-02-01

Necrotizing pancreatitis is a challenging condition that requires surgical treatment commonly and is associated with substantial morbidity and mortality. Over the past decade, new definitions have been developed for standardization of severity of acute and necrotizing pancreatitis, and new management techniques have emerged based on prospective, randomized clinical trials. Review of English-language literature. A new international classification of acute pancreatitis has been developed by PANCREA (Pancreatitis Across Nations Clinical Research and Education Alliance) to replace the Atlanta Classification. It is based on the actual local (whether pancreatic necrosis is present or not, whether it is sterile or infected) and systemic determinants (whether organ failure is present or not, whether it is transient or persistent) of severity. Early management requires goal-directed fluid resuscitation (with avoidance of over-resuscitation and abdominal compartment syndrome), assessment of severity of pancreatitis, diagnostic computed tomography (CT) imaging to assess for necrotizing pancreatitis, consideration of endoscopic retrograde cholangiopancreatography (ERCP) for biliary pancreatitis and early enteral nutrition support. Antibiotic prophylaxis is not recommended. Therapeutic antibiotics are required for treatment of documented infected pancreatic necrosis. The initial treatment of infected pancreatic necrosis is percutaneous catheter or endoscopic (transgastric/transduodenal) drainage with a second drain placement as required. Lack of clinical improvement after these initial procedures warrants consideration of minimally invasive techniques for pancreatic necrosectomy including video-assisted retroperitoneal debridement (VARD), minimally invasive retroperitoneal pancreatectomy (MIRP), or transluminal direct endoscopic necrosectomy (DEN). Open necrosectomy is associated with substantial morbidity, but to date no randomized trial has documented superiority of either minimally invasive or open surgical technique. Additional trials are underway to address this. Severe acute and necrotizing pancreatitis requires a multi-disciplinary treatment strategy that must be individualized for each patient. Optimal treatment of necrotizing pancreatitis now requires a staged, multi-disciplinary, minimally invasive "step-up" approach that includes a team of interventional radiologists, therapeutic endoscopists, and surgeons.

The evolving role of chemotherapy and hematopoietic cell transplants in Ph-positive acute lymphoblastic leukemia in adults.

PubMed

Litzow, M R; Fielding, A K; Luger, S M; Paietta, E; Ofran, Y; Rowe, J M; Goldstone, A H; Tallman, M S; Lazarus, H M

2017-12-01

The introduction of the tyrosine kinase inhibitors (TKI) into the treatment of patients with Ph or BCR-ABL1-positive acute lymphoblastic leukemia has revolutionized the treatment of this poor prognosis acute leukemia. The combination of TKI with chemotherapy has improved response rates and allowed more patients to proceed to allogeneic hematopoietic cell transplant (alloHCT). Older patients have excellent responses to TKI and corticosteroids or in combination with minimal chemotherapy. This raises the question as to whether patients require full-intensity chemotherapy with TKI to achieve molecular remissions. The pediatricians have proposed that cure is achievable without alloHCT in children. These results have suggested that many patients may not require traditional chemotherapy in addition to TKI to achieve remission, and that patients who achieve a negative minimal residual disease state may not require alloHCT. The data in support of these questions is presented here and a suggested future clinical trial design based on these data is proposed.

Sniffer Channel Selection for Monitoring Wireless LANs

NASA Astrophysics Data System (ADS)

Song, Yuan; Chen, Xian; Kim, Yoo-Ah; Wang, Bing; Chen, Guanling

Wireless sniffers are often used to monitor APs in wireless LANs (WLANs) for network management, fault detection, traffic characterization, and optimizing deployment. It is cost effective to deploy single-radio sniffers that can monitor multiple nearby APs. However, since nearby APs often operate on orthogonal channels, a sniffer needs to switch among multiple channels to monitor its nearby APs. In this paper, we formulate and solve two optimization problems on sniffer channel selection. Both problems require that each AP be monitored by at least one sniffer. In addition, one optimization problem requires minimizing the maximum number of channels that a sniffer listens to, and the other requires minimizing the total number of channels that the sniffers listen to. We propose a novel LP-relaxation based algorithm, and two simple greedy heuristics for the above two optimization problems. Through simulation, we demonstrate that all the algorithms are effective in achieving their optimization goals, and the LP-based algorithm outperforms the greedy heuristics.

Syntheses and anti-MRSA activities of the C3 analogs of mansonone F, a potent anti-bacterial sesquiterpenoid: insights into its structural requirements for anti-MRSA activity.

PubMed

Shin, Dong-Yun; Kim, Sun Nam; Chae, Jung-Hyun; Hyun, Soon-Sil; Seo, Seung-Yong; Lee, Yong-Sil; Lee, Kwang-Ok; Kim, Seok-Ho; Lee, Yun-Sang; Jeong, Jae Min; Choi, Nam-Song; Suh, Young-Ger

2004-09-06

Syntheses and excellent anti-MRSA activities of the mansonone F analogs are reported. In addition, the minimal structural requirements for its anti-MRSA activities as well as its structure-activity relationship including the C3 substituents effects on anti-MRSA activity are also described. In particular, this study revealed that both ortho-quinone and tricyclic systems of mansonone F are essential for anti-MRSA activities.

Improved Casting Furnace Conceptual Design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fielding, Randall Sidney; Tolman, David Donald

In an attempt to ensure more consistent casting results and remove some schedule variance associated with casting, an improved casting furnace concept has been developed. The improved furnace uses the existing arc melter hardware and glovebox utilities. The furnace concept was designed around physical and operational requirements such as; a charge sized of less than 30 grams, high heating rates and minimal additional footprint. The conceptual model is shown in the report as well as a summary of how the requirements were met.

On-patient see-through augmented reality based on visual SLAM.

PubMed

Mahmoud, Nader; Grasa, Óscar G; Nicolau, Stéphane A; Doignon, Christophe; Soler, Luc; Marescaux, Jacques; Montiel, J M M

2017-01-01

An augmented reality system to visualize a 3D preoperative anatomical model on intra-operative patient is proposed. The hardware requirement is commercial tablet-PC equipped with a camera. Thus, no external tracking device nor artificial landmarks on the patient are required. We resort to visual SLAM to provide markerless real-time tablet-PC camera location with respect to the patient. The preoperative model is registered with respect to the patient through 4-6 anchor points. The anchors correspond to anatomical references selected on the tablet-PC screen at the beginning of the procedure. Accurate and real-time preoperative model alignment (approximately 5-mm mean FRE and TRE) was achieved, even when anchors were not visible in the current field of view. The system has been experimentally validated on human volunteers, in vivo pigs and a phantom. The proposed system can be smoothly integrated into the surgical workflow because it: (1) operates in real time, (2) requires minimal additional hardware only a tablet-PC with camera, (3) is robust to occlusion, (4) requires minimal interaction from the medical staff.

Energy storage requirements of dc microgrids with high penetration renewables under droop control

DOE PAGES

Weaver, Wayne W.; Robinett, Rush D.; Parker, Gordon G.; ...

2015-01-09

Energy storage is a important design component in microgrids with high penetration renewable sources to maintain the system because of the highly variable and sometimes stochastic nature of the sources. Storage devices can be distributed close to the sources and/or at the microgrid bus. In addition, storage requirements can be minimized with a centralized control architecture, but this creates a single point of failure. Distributed droop control enables a completely decentralized architecture but, the energy storage optimization becomes more difficult. Our paper presents an approach to droop control that enables the local and bus storage requirements to be determined. Givenmore » a priori knowledge of the design structure of a microgrid and the basic cycles of the renewable sources, we found that the droop settings of the sources are such that they minimize both the bus voltage variations and overall energy storage capacity required in the system. This approach can be used in the design phase of a microgrid with a decentralized control structure to determine appropriate droop settings as well as the sizing of energy storage devices.« less

Drying Milk With Boiler Exhaust

NASA Technical Reports Server (NTRS)

Broussard, M. R.

1984-01-01

Considerable energy saved in powdered-milk industry. Only special requirement boiler fired with natural gas or other clean fuel. Boiler flue gas fed to spray drier where it directly contacts product to be dried. Additional heat supplied by auxillary combustor when boiler output is low. Approach adaptable to existing plants with minimal investment because most already equipped with natural-gas-fired boilers.

Spread of Gypsy Moth (Lepidoptera: Lymantriidae) and Its Relationship to Defoliation

Treesearch

Patrick C. Tobin; Stefanie L. Whitmire

2005-01-01

Gypsy moth management is divided into three components: eradication, suppression, and transition zone management. All three components require knowledge of the boundaries that delimit these areas. Additional interest is also placed on the relationship between population spread and defoliation to prepare for the gypsy moth advance in new areas and minimize its impact....

Reforestation as a post-mining land use in the Midwest

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parr, D.E.

1982-12-01

With the passage of the Surface Mining Control and Reclamation Act of 1977 (P.L. 95-87), some very stringent requirements for the successful establishment of trees and shrubs have come into effect. In response to these requirements, AMAX Coal Company is developing a reforestation program for seven surface mines in Indiana and Illinois using the best technology currently available. The program emphasizes obtaining good quality stock, the proper care and handling of stock, the proper planting of the stock, and an effective weed control program. The value of weed control for the establishment and growth of hardwoods has long been recognizedmore » in the forest industry, but has not been used extensively in the reforestation of surface mined lands. The improved survival of tree seedlings with the use of weed control justifies the additional cost. Weed control also enhances the growth of tree seedlings. However, the long term growth of seedlings is questionable due to the compaction resulting from the extensive grading required to achieve approximate original contour. To minimize compaction, a forest area in Illinois is being minimally graded only to the extent necessary for environmental stability. Minimal grading is designed to reduce compaction which in turn will promote the development of a more productive forest resource.« less

[Arthroscopy-guided fracture management. Ankle joint and calcaneus].

PubMed

Schoepp, C; Rixen, D

2013-04-01

Arthroscopic fracture management of the ankle and calcaneus requires a differentiated approach. The aim is to minimize surgical soft tissue damage and to visualize anatomical fracture reduction arthroscopically. Moreover, additional cartilage damage can be detected and treated. The arthroscopic approach is limited by deep impressions of the joint surface needing cancellous bone grafting, by multiple fracture lines on the articular side and by high-grade soft tissue damage. An alternative to the minimally invasive arthroscopic approach is open arthroscopic reduction in conventional osteosynthesis. This facilitates correct assessment of surgical reduction of complex calcaneal fractures, otherwise remaining non-anatomical reduction might not be fluoroscopically detected during surgery.

Neuropathic Minimally Invasive Surgeries (NEMESIS):: Percutaneous Diabetic Foot Surgery and Reconstruction.

PubMed

Miller, Roslyn J

2016-09-01

Patients with peripheral neuropathy associated with ulceration are the nemesis of the orthopedic foot and ankle surgeon. Diabetic foot syndrome is the leading cause of peripheral neuropathy, and its prevalence continues to increase at an alarming rate. Poor wound healing, nonunion, infection, and risk of amputation contribute to the understandable caution toward this patient group. Significant metalwork is required to hold these technically challenging deformities. Neuropathic Minimally Invasive Surgeries is an addition to the toolbox of management of the diabetic foot. It may potentially reduce the risk associated with large wounds and bony correction in this patient group. Copyright © 2016 Elsevier Inc. All rights reserved.

Initial Ares I Bending Filter Design

NASA Technical Reports Server (NTRS)

Jang, Jiann-Woei; Bedrossian, Nazareth; Hall, Robert; Norris, H. Lee; Hall, Charles; Jackson, Mark

2007-01-01

The Ares-I launch vehicle represents a challenging flex-body structural environment for control system design. Software filtering of the inertial sensor output will be required to ensure control system stability and adequate performance. This paper presents a design methodology employing numerical optimization to develop the Ares-I bending filters. The filter design methodology was based on a numerical constrained optimization approach to maximize stability margins while meeting performance requirements. The resulting bending filter designs achieved stability by adding lag to the first structural frequency and hence phase stabilizing the first Ares-I flex mode. To minimize rigid body performance impacts, a priority was placed via constraints in the optimization algorithm to minimize bandwidth decrease with the addition of the bending filters. The bending filters provided here have been demonstrated to provide a stable first stage control system in both the frequency domain and the MSFC MAVERIC time domain simulation.

Investigation of Desiccants and CO2 Sorbents for Exploration Systems 2016-2017

NASA Technical Reports Server (NTRS)

Knox, James C.; Watson, David W.; Giesy, Timothy J.; Cmarik, Gregory E.; Miller, Lee A.

2017-01-01

NASA has embarked on the mission to enable humans to explore deep space, including the goal of sending humans to Mars. This journey will require significant developments in a wide range of technical areas as resupply and early return are not possible. Additionally, mass, power, and volume must be minimized for all phases to maximize propulsion availability. Among the critical areas identified for development are life support systems, which will require increases in reliability as well as reduce resource usage. Two primary points for reliability are the mechanical stability of sorbent pellets and recovery of CO2 sorbent productivity after off-nominal events. In this paper, we discuss the present efforts towards screening and characterizing commercially-available sorbents for extended operation in desiccant and CO2 removal beds. With minimized dusting as the primary criteria, a commercial 13X zeolite was selected and tested for performance and risk.

Variability of Photodynamic Killing in Escherichia coli and Avoidance of Variability with Agar

PubMed Central

O'Bryan, Corliss; Harrison, Arthur P.

1971-01-01

Photodynamic killing of Escherichia coli in acridine orange is influenced by the composition of the containing vessel, and after high kill the variance between replicate suspensions is greater than attributable solely to sampling and plating. Addition of agar minimizes both phenomena, but a higher illumination dose is required to produce the same degree of killing. PMID:4934057

The Impact of 3D Stacking and Technology Scaling on the Power and Area of Stereo Matching Processors.

PubMed

Ok, Seung-Ho; Lee, Yong-Hwan; Shim, Jae Hoon; Lim, Sung Kyu; Moon, Byungin

2017-02-22

Recently, stereo matching processors have been adopted in real-time embedded systems such as intelligent robots and autonomous vehicles, which require minimal hardware resources and low power consumption. Meanwhile, thanks to the through-silicon via (TSV), three-dimensional (3D) stacking technology has emerged as a practical solution to achieving the desired requirements of a high-performance circuit. In this paper, we present the benefits of 3D stacking and process technology scaling on stereo matching processors. We implemented 2-tier 3D-stacked stereo matching processors with GlobalFoundries 130-nm and Nangate 45-nm process design kits and compare them with their two-dimensional (2D) counterparts to identify comprehensive design benefits. In addition, we examine the findings from various analyses to identify the power benefits of 3D-stacked integrated circuit (IC) and device technology advancements. From experiments, we observe that the proposed 3D-stacked ICs, compared to their 2D IC counterparts, obtain 43% area, 13% power, and 14% wire length reductions. In addition, we present a logic partitioning method suitable for a pipeline-based hardware architecture that minimizes the use of TSVs.

The Impact of 3D Stacking and Technology Scaling on the Power and Area of Stereo Matching Processors

PubMed Central

Ok, Seung-Ho; Lee, Yong-Hwan; Shim, Jae Hoon; Lim, Sung Kyu; Moon, Byungin

2017-01-01

Recently, stereo matching processors have been adopted in real-time embedded systems such as intelligent robots and autonomous vehicles, which require minimal hardware resources and low power consumption. Meanwhile, thanks to the through-silicon via (TSV), three-dimensional (3D) stacking technology has emerged as a practical solution to achieving the desired requirements of a high-performance circuit. In this paper, we present the benefits of 3D stacking and process technology scaling on stereo matching processors. We implemented 2-tier 3D-stacked stereo matching processors with GlobalFoundries 130-nm and Nangate 45-nm process design kits and compare them with their two-dimensional (2D) counterparts to identify comprehensive design benefits. In addition, we examine the findings from various analyses to identify the power benefits of 3D-stacked integrated circuit (IC) and device technology advancements. From experiments, we observe that the proposed 3D-stacked ICs, compared to their 2D IC counterparts, obtain 43% area, 13% power, and 14% wire length reductions. In addition, we present a logic partitioning method suitable for a pipeline-based hardware architecture that minimizes the use of TSVs. PMID:28241437

The Costs of Legislated Minimal Competency Requirements. A background paper prepared for the Minimal Cometency Workshops sponsored by the Education Commission of the States and the National Institute of Education.

ERIC Educational Resources Information Center

Anderson, Barry D.

Little is known about the costs of setting up and implementing legislated minimal competency testing (MCT). To estimate the financial obstacles which lie between the idea and its implementation, MCT requirements are viewed from two perspectives. The first, government regulation, views legislated minimal competency requirements as an attempt by the…

An adaptive vector quantization scheme

NASA Technical Reports Server (NTRS)

Cheung, K.-M.

1990-01-01

Vector quantization is known to be an effective compression scheme to achieve a low bit rate so as to minimize communication channel bandwidth and also to reduce digital memory storage while maintaining the necessary fidelity of the data. However, the large number of computations required in vector quantizers has been a handicap in using vector quantization for low-rate source coding. An adaptive vector quantization algorithm is introduced that is inherently suitable for simple hardware implementation because it has a simple architecture. It allows fast encoding and decoding because it requires only addition and subtraction operations.

Education, licensure, and certification of school nurses: position statement.

PubMed

2013-07-01

It is the position of the National Association of School Nurses (NASN) that every school-age child deserves a school nurse who has a baccalaureate degree in nursing from an accredited college or university and is licensed as a registered nurse through the state board of nursing. These requirements constitute minimal preparation needed to practice at the entry level of school nursing (American Nurses Association [ANA] & NASN, 2011). Additionally, NASN supports state school nurse certification, where required, and promotes national certification of school nurses through the National Board for Certification of School Nurses.

Environmental considerations for 3D seismic in Louisianna wetlands

DOE Office of Scientific and Technical Information (OSTI.GOV)

Browning, G.; Dillane, T.; Baaren, P. van

1996-11-01

Louisiana swamps have been host to seismic crews for many years. Results from recent 3D surveys indicate that well planned and executed seismic operations have a minimal and short term impact in these environmentally sensitive wetlands. Pre-planning identifies challenges that require use of improved technology and work procedures. These include multi-channel radio telemetry recording systems, ramming of dynamite and hydrophones as opposed to drilling, DGPS positioning and coordinated use of Airboats, buggies and helicopters. In addition to minimal environmental impact, increased data quality, reduced cost and shorter project duration have been achieved as a result of these efforts. Unlike 2Dmore » surveys, where profile positioning is flexible, 3D surveys involve high density coverage over many square miles operated by numerous personnel. Survey design includes minimizing repeated traffic and crossing points. Survey operations require environmental participation and commitment from every person involved in the project. This includes a thorough orientation and training program with strong emphasis on environmental sensitivity and awareness. Close co-ordination between regulatory agencies, clients and the contractor is a key factor in all aspects of the survey planning and operation. Benefits from these efforts are significant, measurable and continue to improve.« less

Design and simulation of a fast-charging station for plug-in hybrid electric vehicle (PHEV) batteries

NASA Astrophysics Data System (ADS)

de Leon, Nathalie Pulmones

2011-12-01

With the increasing interest in green technologies in transportation, plug-in hybrid electric vehicles (PHEV) have proven to be the best short-term solution to minimize greenhouse gas emissions. Despite such interest, conventional vehicle drivers are still reluctant in using such a new technology, mainly because of the long duration (4-8 hours) required to charge PHEV batteries with the currently existing Level I and II chargers. For this reason, Level III fast-charging stations capable of reducing the charging duration to 10-15 minutes are being considered. The present thesis focuses on the design of a fast-charging station that uses, in addition to the electrical grid, two stationary energy storage devices: a flywheel energy storage and a supercapacitor. The power electronic converters used for the interface of the energy sources with the charging station are designed. The design also focuses on the energy management that will minimize the PHEV battery charging duration as well as the duration required to recharge the energy storage devices. For this reason, an algorithm that minimizes durations along with its mathematical formulation is proposed, and its application in fast charging environment will be illustrated by means of two scenarios.

Uprated fine guidance sensor study

NASA Technical Reports Server (NTRS)

1984-01-01

Future orbital observatories will require star trackers of extremely high precision. These sensors must maintain high pointing accuracy and pointing stability simultaneously with a low light level signal from a guide star. To establish the fine guidance sensing requirements and to evaluate candidate fine guidance sensing concepts, the Space Telescope Optical Telescope Assembly was used as the reference optical system. The requirements review was separated into three areas: Optical Telescope Assembly (OTA), Fine Guidance Sensing and astrometry. The results show that the detectors should be installed directly onto the focal surface presented by the optics. This would maximize throughput and minimize point stability error by not incoporating any additional optical elements.

Design and Requirements Creep In A Build-To-Print Mission

NASA Technical Reports Server (NTRS)

Peabody, Sharon A.; Otero, Veronica

2017-01-01

Build-to-Print designs, or rebuilds of flight proven designs, are attractive to mission stakeholders, as they give the appearance of minimal engineering development cost, risk, and schedule. The reality is that seldom is a project an exact duplicate of a predecessor. Mission reclassification, improvements in hardware, and science objective changes can all serve as a source of requirements and design creep and have ramifications often not fully anticipated during initial proposals. The Thermal Infrared Sensor Instrument (TIRS) was a late addition to the LandSat-8 program to provide infrared imaging to measure evapotranspiration for water cycle management. To meet the launch requirements for LandSat-8, instrument design life requirements were relaxed, the sensor development expedited, and technology development was minimized. Consequently, TIRS was designed as a higher risk instrument, with less redundancy than an instrument critical to mission success. After the successful LandSat-8 launch in 2013 and instrument performance, a rebuild of the instrument for the next LandSat spacecraft was included in the baseline mission success criteria. This paper discusses the technical challenges encountered during the rebuild of the TIRS-2 (Thermal Infrared Sensor 2) instrument and the resultant impacts on the thermal system design.

Systems Biology Perspectives on Minimal and Simpler Cells

PubMed Central

Xavier, Joana C.; Patil, Kiran Raosaheb

2014-01-01

SUMMARY The concept of the minimal cell has fascinated scientists for a long time, from both fundamental and applied points of view. This broad concept encompasses extreme reductions of genomes, the last universal common ancestor (LUCA), the creation of semiartificial cells, and the design of protocells and chassis cells. Here we review these different areas of research and identify common and complementary aspects of each one. We focus on systems biology, a discipline that is greatly facilitating the classical top-down and bottom-up approaches toward minimal cells. In addition, we also review the so-called middle-out approach and its contributions to the field with mathematical and computational models. Owing to the advances in genomics technologies, much of the work in this area has been centered on minimal genomes, or rather minimal gene sets, required to sustain life. Nevertheless, a fundamental expansion has been taking place in the last few years wherein the minimal gene set is viewed as a backbone of a more complex system. Complementing genomics, progress is being made in understanding the system-wide properties at the levels of the transcriptome, proteome, and metabolome. Network modeling approaches are enabling the integration of these different omics data sets toward an understanding of the complex molecular pathways connecting genotype to phenotype. We review key concepts central to the mapping and modeling of this complexity, which is at the heart of research on minimal cells. Finally, we discuss the distinction between minimizing the number of cellular components and minimizing cellular complexity, toward an improved understanding and utilization of minimal and simpler cells. PMID:25184563

Three Dimensional Projection Environment for Molecular Design and Surgical Simulation

DTIC Science & Technology

2011-08-01

bypasses the cumbersome meshing process . The deformation model is only comprised of mass nodes, which are generated by sampling the object volume before...force should minimize the penetration volume, the haptic feedback force is derived directly. Additionally, a post- processing technique is developed to...render distinct physi-cal tissue properties across different interaction areas. The proposed approach does not require any pre- processing and is

Development of standardized specifications for silicon solar cells

NASA Technical Reports Server (NTRS)

Scott-Monck, J. A.

1977-01-01

A space silicon solar cell assembly (cell and coverglass) specification aimed at standardizing the diverse requirements of current cell or assembly specifications was developed. This specification was designed to minimize both the procurement and manufacturing costs for space qualified silicon solar cell assembilies. In addition, an impact analysis estimating the technological and economic effects of employing a standardized space silicon solar cell assembly was performed.

Optimizing Segmental Bone Regeneration Using Functionally Graded Scaffolds

DTIC Science & Technology

2012-10-01

Such a model system would allow more realistic assessment of different clinical treatment options in a rapid, cost -efficient, and safe man- ner...along with MichealiseMenten kinetics. Genetic algorithm [37] was adopted to minimize the cost function in Equation (14). Fig. 3 shows that simulated...associated with autografts, such as high cost , requirement of additional surgeries, donor-site morbidity, and limiting autographs for the treatment

Results of completion arteriography after minimally invasive off-pump coronary artery bypass.

PubMed

Hoff, Steven J; Ball, Stephen K; Leacche, Marzia; Solenkova, Natalia; Umakanthan, Ramanan; Petracek, Michael R; Ahmad, Rashid; Greelish, James P; Walker, Kristie; Byrne, John G

2011-01-01

The benefits of a minimally invasive approach to off-pump coronary artery bypass remain controversial. The value of completion arteriography in validating this technique has not been investigated. From April 2007 to October 2009, fifty-six patients underwent isolated minimally invasive coronary artery bypass grafting through a left thoracotomy without cardiopulmonary bypass. Forty-three of these patients underwent completion arteriography. Sixty-five grafts were performed in these 56 patients, (average, 1.2 grafts per patient; range, 1 to 3). Forty-eight grafts were studied in the 43 patients undergoing completion arteriography. There were 4 findings on arteriogram leading to further immediate intervention (8.3%). These included 3 grafts with anastomotic stenoses or spasm requiring stent placement, and 1 patient who had limited dissection in the left internal mammary artery graft and underwent placement of an additional vein graft. These findings were independent of electrocardiographic changes or hemodynamic instability. The remainder of the studies showed no significant abnormalities. There were no deaths. One patient who did not have a completion arteriogram suffered a postoperative myocardial infarction requiring stent placement for anastomotic stenosis. Patients were discharged home an average of 6.8 days postoperatively. There were no instances of renal dysfunction postoperatively attributable to catheterization. Minimally invasive coronary artery bypass is safe and effective. Findings of completion arteriography occasionally reveal previously under-recognized findings that, if corrected in a timely fashion, could potentially impact graft patency and clinical outcomes. Our experience validates this minimally invasive technique. Copyright © 2011 The Society of Thoracic Surgeons. Published by Elsevier Inc. All rights reserved.

Toxicity Minimized Cryoprotectant Addition and Removal Procedures for Adherent Endothelial Cells

PubMed Central

Davidson, Allyson Fry; Glasscock, Cameron; McClanahan, Danielle R.; Benson, James D.; Higgins, Adam Z.

2015-01-01

Ice-free cryopreservation, known as vitrification, is an appealing approach for banking of adherent cells and tissues because it prevents dissociation and morphological damage that may result from ice crystal formation. However, current vitrification methods are often limited by the cytotoxicity of the concentrated cryoprotective agent (CPA) solutions that are required to suppress ice formation. Recently, we described a mathematical strategy for identifying minimally toxic CPA equilibration procedures based on the minimization of a toxicity cost function. Here we provide direct experimental support for the feasibility of these methods when applied to adherent endothelial cells. We first developed a concentration- and temperature-dependent toxicity cost function by exposing the cells to a range of glycerol concentrations at 21°C and 37°C, and fitting the resulting viability data to a first order cell death model. This cost function was then numerically minimized in our state constrained optimization routine to determine addition and removal procedures for 17 molal (mol/kg water) glycerol solutions. Using these predicted optimal procedures, we obtained 81% recovery after exposure to vitrification solutions, as well as successful vitrification with the relatively slow cooling and warming rates of 50°C/min and 130°C/min. In comparison, conventional multistep CPA equilibration procedures resulted in much lower cell yields of about 10%. Our results demonstrate the potential for rational design of minimally toxic vitrification procedures and pave the way for extension of our optimization approach to other adherent cell types as well as more complex systems such as tissues and organs. PMID:26605546

Method for materials deposition by ablation transfer processing

DOEpatents

Weiner, Kurt H.

1996-01-01

A method in which a thin layer of semiconducting, insulating, or metallic material is transferred by ablation from a source substrate, coated uniformly with a thin layer of said material, to a target substrate, where said material is desired, with a pulsed, high intensity, patternable beam of energy. The use of a patternable beam allows area-selective ablation from the source substrate resulting in additive deposition of the material onto the target substrate which may require a very low percentage of the area to be covered. Since material is placed only where it is required, material waste can be minimized by reusing the source substrate for depositions on multiple target substrates. Due to the use of a pulsed, high intensity energy source the target substrate remains at low temperature during the process, and thus low-temperature, low cost transparent glass or plastic can be used as the target substrate. The method can be carried out atmospheric pressures and at room temperatures, thus eliminating vacuum systems normally required in materials deposition processes. This invention has particular application in the flat panel display industry, as well as minimizing materials waste and associated costs.

PI controller design for indirect vector controlled induction motor: A decoupling approach.

PubMed

Jain, Jitendra Kr; Ghosh, Sandip; Maity, Somnath; Dworak, Pawel

2017-09-01

Decoupling of the stator currents is important for smoother torque response of indirect vector controlled induction motors. Typically, feedforward decoupling is used to take care of current coupling that requires exact knowledge of motor parameters, additional circuitry and signal processing. In this paper, a method is proposed to design the regulating proportional-integral gains that minimize coupling without any requirement of the additional decoupler. The variation of the coupling terms for change in load torque is considered as the performance measure. An iterative linear matrix inequality based H ∞ control design approach is used to obtain the controller gains. A comparison between the feedforward and the proposed decoupling schemes is presented through simulation and experimental results. The results show that the proposed scheme is simple yet effective even without additional block or burden on signal processing. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

Influence of gag and RRE Sequences on HIV-1 RNA Packaging Signal Structure and Function.

PubMed

Kharytonchyk, Siarhei; Brown, Joshua D; Stilger, Krista; Yasin, Saif; Iyer, Aishwarya S; Collins, John; Summers, Michael F; Telesnitsky, Alice

2018-07-06

The packaging signal (Ψ) and Rev-responsive element (RRE) enable unspliced HIV-1 RNAs' export from the nucleus and packaging into virions. For some retroviruses, engrafting Ψ onto a heterologous RNA is sufficient to direct encapsidation. In contrast, HIV-1 RNA packaging requires 5' leader Ψ elements plus poorly defined additional features. We previously defined minimal 5' leader sequences competitive with intact Ψ for HIV-1 packaging, and here examined the potential roles of additional downstream elements. The findings confirmed that together, HIV-1 5' leader Ψ sequences plus a nuclear export element are sufficient to specify packaging. However, RNAs trafficked using a heterologous export element did not compete well with RNAs using HIV-1's RRE. Furthermore, some RNA additions to well-packaged minimal vectors rendered them packaging-defective. These defects were rescued by extending gag sequences in their native context. To understand these packaging defects' causes, in vitro dimerization properties of RNAs containing minimal packaging elements were compared to RNAs with sequence extensions that were or were not compatible with packaging. In vitro dimerization was found to correlate with packaging phenotypes, suggesting that HIV-1 evolved to prevent 5' leader residues' base pairing with downstream residues and misfolding of the packaging signal. Our findings explain why gag sequences have been implicated in packaging and show that RRE's packaging contributions appear more specific than nuclear export alone. Paired with recent work showing that sequences upstream of Ψ can dictate RNA folds, the current work explains how genetic context of minimal packaging elements contributes to HIV-1 RNA fate determination. Copyright © 2018 Elsevier Ltd. All rights reserved.

Multi-Objective Online Initialization of Spacecraft Formations

NASA Technical Reports Server (NTRS)

Jeffrey, Matthew; Breger, Louis; How, Jonathan P.

2007-01-01

This paper extends a previously developed method for finding spacecraft initial conditions (ICs) that minimize the drift resulting from J2 disturbances while also minimizing the fuel required to attain those ICs. It generalizes the single spacecraft optimization to a formation-wide optimization valid for an arbitrary number of vehicles. Additionally, the desired locations of the spacecraft, separate from the starting location, can be specified, either with respect to a reference orbit, or relative to the other spacecraft in the formation. The three objectives (minimize drift, minimize fuel, and maintain a geometric template) are expressed as competing costs in a linear optimization, and are traded against one another through the use of scalar weights. By carefully selecting these weights and re-initializing the formation at regular intervals, a closed-loop, formation-wide control system is created. This control system can be used to reconfigure the formations on the fly, and creates fuel-efficient plans by placing the spacecraft in semi-invariant orbits. The overall approach is demonstrated through nonlinear simulations for two formations a GEO orbit, and an elliptical orbit.

Droplet-Based Segregation and Extraction of Concentrated Samples

DOE Office of Scientific and Technical Information (OSTI.GOV)

Buie, C R; Buckley, P; Hamilton, J

2007-02-23

Microfluidic analysis often requires sample concentration and separation techniques to isolate and detect analytes of interest. Complex or scarce samples may also require an orthogonal separation and detection method or off-chip analysis to confirm results. To perform these additional steps, the concentrated sample plug must be extracted from the primary microfluidic channel with minimal sample loss and dilution. We investigated two extraction techniques; injection of immiscible fluid droplets into the sample stream (''capping'''') and injection of the sample into an immiscible fluid stream (''extraction''). From our results we conclude that capping is the more effective partitioning technique. Furthermore, this functionalitymore » enables additional off-chip post-processing procedures such as DNA/RNA microarray analysis, realtime polymerase chain reaction (RT-PCR), and culture growth to validate chip performance.« less

Orbital transfer vehicle launch operations study. Volume 2: Detailed summary

NASA Technical Reports Server (NTRS)

1986-01-01

A series of Operational Design Drivers were identified. Several of these could have significant impact(s) on program costs. These recommendations, for example, include such items as: complete factory assembly and checkout prior to shipment to the ground launch site to make significant reductions in time required at the launch site as well as overall manpower required to do this work; minimize use of nonstandard equipment when orbiter provided equipment is available; and require commonality (or interchangeability) of subsystem equipment elements that are common to the space station, Orbit Maneuvering Vehicles, and/or Orbit Transfer Vehicles. Several additional items were identified that will require a significant amount of management attention (and direction) to resolve. Key elements of the space based processing plans are discussed.

Reducing the Budget Deficit: The President’s Fiscal Commission and Other Initiatives

DTIC Science & Technology

2011-04-29

numerous additional savings proposals from the Medicare and Medicaid programs, medical malpractice reform, and transforming the Federal Employees...taxes will likely be required. The sacrifices made today are essential to minimizing the size of potential programmatic cuts or tax increases, reducing...detailing possible ways that the country can put itself on a more sustainable fiscal path. Though the fiscal reform plans differ, they all have several

A Model of Batch Scheduling for a Single Batch Processor with Additional Setups to Minimize Total Inventory Holding Cost of Parts of a Single Item Requested at Multi-due-date

NASA Astrophysics Data System (ADS)

Hakim Halim, Abdul; Ernawati; Hidayat, Nita P. A.

2018-03-01

This paper deals with a model of batch scheduling for a single batch processor on which a number of parts of a single items are to be processed. The process needs two kinds of setups, i. e., main setups required before processing any batches, and additional setups required repeatedly after the batch processor completes a certain number of batches. The parts to be processed arrive at the shop floor at the times coinciding with their respective starting times of processing, and the completed parts are to be delivered at multiple due dates. The objective adopted for the model is that of minimizing total inventory holding cost consisting of holding cost per unit time for a part in completed batches, and that in in-process batches. The formulation of total inventory holding cost is derived from the so-called actual flow time defined as the interval between arrival times of parts at the production line and delivery times of the completed parts. The actual flow time satisfies not only minimum inventory but also arrival and delivery just in times. An algorithm to solve the model is proposed and a numerical example is shown.

Model for Assembly Line Re-Balancing Considering Additional Capacity and Outsourcing to Face Demand Fluctuations

NASA Astrophysics Data System (ADS)

Samadhi, TMAA; Sumihartati, Atin

2016-02-01

The most critical stage in a garment industry is sewing process, because generally, it consists of a number of operations and a large number of sewing machines for each operation. Therefore, it requires a balancing method that can assign task to work station with balance workloads. Many studies on assembly line balancing assume a new assembly line, but in reality, due to demand fluctuation and demand increased a re-balancing is needed. To cope with those fluctuating demand changes, additional capacity can be carried out by investing in spare sewing machine and paying for sewing service through outsourcing. This study develops an assembly line balancing (ALB) model on existing line to cope with fluctuating demand change. Capacity redesign is decided if the fluctuation demand exceeds the available capacity through a combination of making investment on new machines and outsourcing while considering for minimizing the cost of idle capacity in the future. The objective of the model is to minimize the total cost of the line assembly that consists of operating costs, machine cost, adding capacity cost, losses cost due to idle capacity and outsourcing costs. The model develop is based on an integer programming model. The model is tested for a set of data of one year demand with the existing number of sewing machines of 41 units. The result shows that additional maximum capacity up to 76 units of machine required when there is an increase of 60% of the average demand, at the equal cost parameters..

Systems biology perspectives on minimal and simpler cells.

PubMed

Xavier, Joana C; Patil, Kiran Raosaheb; Rocha, Isabel

2014-09-01

The concept of the minimal cell has fascinated scientists for a long time, from both fundamental and applied points of view. This broad concept encompasses extreme reductions of genomes, the last universal common ancestor (LUCA), the creation of semiartificial cells, and the design of protocells and chassis cells. Here we review these different areas of research and identify common and complementary aspects of each one. We focus on systems biology, a discipline that is greatly facilitating the classical top-down and bottom-up approaches toward minimal cells. In addition, we also review the so-called middle-out approach and its contributions to the field with mathematical and computational models. Owing to the advances in genomics technologies, much of the work in this area has been centered on minimal genomes, or rather minimal gene sets, required to sustain life. Nevertheless, a fundamental expansion has been taking place in the last few years wherein the minimal gene set is viewed as a backbone of a more complex system. Complementing genomics, progress is being made in understanding the system-wide properties at the levels of the transcriptome, proteome, and metabolome. Network modeling approaches are enabling the integration of these different omics data sets toward an understanding of the complex molecular pathways connecting genotype to phenotype. We review key concepts central to the mapping and modeling of this complexity, which is at the heart of research on minimal cells. Finally, we discuss the distinction between minimizing the number of cellular components and minimizing cellular complexity, toward an improved understanding and utilization of minimal and simpler cells. Copyright © 2014, American Society for Microbiology. All Rights Reserved.

A Simplified Shuttle Payload Thermal Analyzer /SSPTA/ program

NASA Technical Reports Server (NTRS)

Bartoszek, J. T.; Huckins, B.; Coyle, M.

1979-01-01

A simple thermal analysis program for Space Shuttle payloads has been developed to accommodate the user who requires an easily understood but dependable analytical tool. The thermal analysis program includes several thermal subprograms traditionally employed in spacecraft thermal studies, a data management system for data generated by the subprograms, and a master program to coordinate the data files and thermal subprograms. The language and logic used to run the thermal analysis program are designed for the small user. In addition, analytical and storage techniques which conserve computer time and minimize core requirements are incorporated into the program.

Anesthetic management of the SRS™ Endoscopic Stapling System for gastro-esophageal reflux disease.

PubMed

Topuz, Ufuk; Umutoglu, Tarik; Bakan, Mefkur; Ozturk, Erdogan

2013-01-14

The SRS(TM) Endoscopic Stapling System (Medigus, Tel Aviv, Israel) is a new tool capable of creating a totally endoscopic fundoplication, combined with an endoscope, endoscopic ultrasound and a surgical stapler. SRS(TM) endoscopic stapling for gastro-esophageal reflux disease is a minimally invasive, outpatient procedure, which requires general anesthesia with positive-pressure ventilation. Keeping the patient on positive end-expiratory pressure (PEEP) may minimize the pressure gradient between the esophagus and the mediastinum, as well as help to prevent air from leaking around the screws and causing pneumomediastinum. In addition, in patients with hiatal hernia, higher PEEP levels may be required to increase intra-thoracic pressure and to force the stomach to slide into the abdomen for ease of endoscopy. We advise smoother emergence from anesthesia, taking precautions for retching, postoperative nausea and vomiting (PONV), while coughing and gagging during extubation and PONV may affect the success of the procedure. Total intravenous anesthesia with propofol and remifentanil seems to be a good choice for these reasons.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Woohyun; Katipamula, Srinivas; Lutes, Robert G.

This report describes how the intelligent load control (ILC) algorithm can be implemented to achieve peak demand reduction while minimizing impacts on occupant comfort. The algorithm was designed to minimize the additional sensors and minimum configuration requirements to enable a scalable and cost-effective implementation for both large and small-/medium-sized commercial buildings. The ILC algorithm uses an analytic hierarchy process (AHP) to dynamically prioritize the available curtailable loads based on both quantitative (deviation of zone conditions from set point) and qualitative rules (types of zone). Although the ILC algorithm described in this report was highly tailored to work with rooftop units,more » it can be generalized for application to other building loads such as variable-air-volume (VAV) boxes and lighting systems.« less

A preliminary area survey of neutron radiation levels associated with the NASA variable energy cyclotron horizontal neutron delivery system

NASA Technical Reports Server (NTRS)

Roberts, W. K.; Leonard, R. F.

1976-01-01

The 25 MeV deuteron beam from the NASA variable energy cyclotron incident on a thick beryllium target will deliver a tissue neutron dose rate of 2.14 rad micron A-min at a source to skin distance of 125 cm. A neutron survey of the existing hallways with various shielding configurations made during operating of the horizontal neutron delivery system indicates that minimal amounts of additional neutron shielding material are required to provide a low level radiation environment within a self-contained neutron therapy control station. Measurements also indicate that the primary neutron distribution delivered by a planned vertical delivery system will be minimally perturbed by neutrons backscattered from the floor.

Spin coating apparatus

DOEpatents

Torczynski, John R.

2000-01-01

A spin coating apparatus requires less cleanroom air flow than prior spin coating apparatus to minimize cleanroom contamination. A shaped exhaust duct from the spin coater maintains process quality while requiring reduced cleanroom air flow. The exhaust duct can decrease in cross section as it extends from the wafer, minimizing eddy formation. The exhaust duct can conform to entrainment streamlines to minimize eddy formation and reduce interprocess contamination at minimal cleanroom air flow rates.

The impact of preventable disruption on the operative time for minimally invasive surgery.

PubMed

Al-Hakim, Latif

2011-10-01

Current ergonomic studies show that disruption exposes surgical teams to stress and musculoskeletal disorders. This study considers minimally invasive surgery as a sociotechnical process subjected to a variety of disruption events other than those recognized by ergonomic science. The research takes into consideration the impact of preventable disruption on operating time rather than on the physical and emotional status of the surgical team. Events inside operating rooms that disturbed operative time were recorded for 17 minimally invasive surgeries. The disruption events were classified into four main areas: prerequisite requirements, work design, communication during surgery, and other. Each area was further classified according to sources of disruption. Altogether, 11 sources of disruption were identified: patient record, protocol and policy, surgical requirements and surgeon preferences, operating table and patient positioning, arrangement of instruments, lighting, monitor, clothing, surgical teamwork, coordination, and other. Disruption prolonged operative time by more than 32%. Teamwork forms the main source of disruption followed by operating table and patient positioning and arrangement of instruments. These three sources represented approximately 20% of operative time. Failure to follow principles of work design had a significant negative impact, lengthening operative time by approximately 15%. Although lighting and monitors had a relatively small impact on operative time, these factors could create inconvenience and stress within the surgical teams. In addition, the effect of failure to follow surgical protocols and policies or having incomplete patient records may have a limited effect on operative time but could have serious consequences. This report demonstrates that preventable disruption caused an increase in operative time and forced surgeons and patients to endure unnecessary delay of more than 32%. Such additional time could be used to deal with the pressure of emergency cases and to reduce waiting lists for elective surgery.

Thermal Desorption Capability Development for Enhanced On-site Health Risk Assessment: HAPSITE (registered trademark) ER Passive Sampling in the Field

DTIC Science & Technology

2015-06-07

Field-Portable Gas Chromatograph-Mass Spectrometer.” Forensic Toxicol, 2006, 24, 17-22. Smith, P. “Person-Portable Gas Chromatography : Rapid Temperature...bench-top Gas Chromatograph-Mass Spectrometer (GC-MS) system (ISQ). Nine sites were sampled and analyzed for compounds using Environmental Protection...extraction methods for Liquid Chromatography -MS (LC- MS). Additionally, TD is approximately 1000X more sensitive, requires minimal sample preparation

Advanced Lubrication for Energy Efficiency, Durability and Lower Maintenance Costs of Advanced Naval Components and Systems

DTIC Science & Technology

2010-08-20

for transmitting the required power and torque. The proper gear set has also been sized to insure life expectancy of the test rig. The shaft design ...these at minimal cost and great environmental safety. These materials specifically designed on antiwear and extreme pressure chemistries can...nanolubricant additives are designed as surface-stabilized nanomaterials that are dispersed in a hydrocarbon medium for maximum effectiveness. This

A linear shift-invariant image preprocessing technique for multispectral scanner systems

NASA Technical Reports Server (NTRS)

Mcgillem, C. D.; Riemer, T. E.

1973-01-01

A linear shift-invariant image preprocessing technique is examined which requires no specific knowledge of any parameter of the original image and which is sufficiently general to allow the effective radius of the composite imaging system to be arbitrarily shaped and reduced, subject primarily to the noise power constraint. In addition, the size of the point-spread function of the preprocessing filter can be arbitrarily controlled, thus minimizing truncation errors.

The new guidelines for paternity analysis in Germany-how many STR loci are necessary when investigating duo cases?

PubMed

Poetsch, Micaela; Preusse-Prange, Andrea; Schwark, Thorsten; von Wurmb-Schwark, Nicole

2013-07-01

The requirements in the new German guidelines for paternity analysis have not only changed according to the so-called Gendiagnostikgesetz, the new German law regulating human genetic as well as paternity analyses, but also regarding the minimal number of short tandem repeats (STRs) which should be investigated (15 STRs) and the minimal required average exclusion chance (99.999 %). Even in paternity analyses involving only two people (e.g., father and child or mother and child), this exclusion chance is mandatory. A retrospective analysis of 330 father-child cases from our routine investigations showed in 142 cases (43 %) an individual exclusion chance below 99.999 % when using 15 STRs as required, in our routine work provided by the Powerplex® 16 kit which is reported to have an average exclusion chance of 99.988 %. Therefore, these same 330 father-child pairs were additionally analysed using the Powerplex® 21 kit and 120 of these duos were additionally analysed using the Powerplex® ESX17 kit enabling the analysis of 20 or 16 loci respectively. Now, an individual exclusion chance of more than 99.999 % could be achieved in 95.5 % (Powerplex® 21; calculation without the results of D6S1043), 98.8 % (Powerplex® 21; calculation with the results of D6S1043, using allele frequencies established in this study for a German and a West African population) and 98.3 % (Powerplex® ESX17). These data clearly demonstrate that in duo cases, more than the required 15 STR loci have to be investigated to obtain sufficient results.

Fermion-to-qubit mappings with varying resource requirements for quantum simulation

NASA Astrophysics Data System (ADS)

Steudtner, Mark; Wehner, Stephanie

2018-06-01

The mapping of fermionic states onto qubit states, as well as the mapping of fermionic Hamiltonian into quantum gates enables us to simulate electronic systems with a quantum computer. Benefiting the understanding of many-body systems in chemistry and physics, quantum simulation is one of the great promises of the coming age of quantum computers. Interestingly, the minimal requirement of qubits for simulating Fermions seems to be agnostic of the actual number of particles as well as other symmetries. This leads to qubit requirements that are well above the minimal requirements as suggested by combinatorial considerations. In this work, we develop methods that allow us to trade-off qubit requirements against the complexity of the resulting quantum circuit. We first show that any classical code used to map the state of a fermionic Fock space to qubits gives rise to a mapping of fermionic models to quantum gates. As an illustrative example, we present a mapping based on a nonlinear classical error correcting code, which leads to significant qubit savings albeit at the expense of additional quantum gates. We proceed to use this framework to present a number of simpler mappings that lead to qubit savings with a more modest increase in gate difficulty. We discuss the role of symmetries such as particle conservation, and savings that could be obtained if an experimental platform could easily realize multi-controlled gates.

Method for materials deposition by ablation transfer processing

DOEpatents

Weiner, K.H.

1996-04-16

A method in which a thin layer of semiconducting, insulating, or metallic material is transferred by ablation from a source substrate, coated uniformly with a thin layer of said material, to a target substrate, where said material is desired, with a pulsed, high intensity, patternable beam of energy. The use of a patternable beam allows area-selective ablation from the source substrate resulting in additive deposition of the material onto the target substrate which may require a very low percentage of the area to be covered. Since material is placed only where it is required, material waste can be minimized by reusing the source substrate for depositions on multiple target substrates. Due to the use of a pulsed, high intensity energy source the target substrate remains at low temperature during the process, and thus low-temperature, low cost transparent glass or plastic can be used as the target substrate. The method can be carried out atmospheric pressures and at room temperatures, thus eliminating vacuum systems normally required in materials deposition processes. This invention has particular application in the flat panel display industry, as well as minimizing materials waste and associated costs. 1 fig.

Accelerating an Ordered-Subset Low-Dose X-Ray Cone Beam Computed Tomography Image Reconstruction with a Power Factor and Total Variation Minimization.

PubMed

Huang, Hsuan-Ming; Hsiao, Ing-Tsung

2016-01-01

In recent years, there has been increased interest in low-dose X-ray cone beam computed tomography (CBCT) in many fields, including dentistry, guided radiotherapy and small animal imaging. Despite reducing the radiation dose, low-dose CBCT has not gained widespread acceptance in routine clinical practice. In addition to performing more evaluation studies, developing a fast and high-quality reconstruction algorithm is required. In this work, we propose an iterative reconstruction method that accelerates ordered-subsets (OS) reconstruction using a power factor. Furthermore, we combine it with the total-variation (TV) minimization method. Both simulation and phantom studies were conducted to evaluate the performance of the proposed method. Results show that the proposed method can accelerate conventional OS methods, greatly increase the convergence speed in early iterations. Moreover, applying the TV minimization to the power acceleration scheme can further improve the image quality while preserving the fast convergence rate.

A 3D virtual reality simulator for training of minimally invasive surgery.

PubMed

Mi, Shao-Hua; Hou, Zeng-Gunag; Yang, Fan; Xie, Xiao-Liang; Bian, Gui-Bin

2014-01-01

For the last decade, remarkable progress has been made in the field of cardiovascular disease treatment. However, these complex medical procedures require a combination of rich experience and technical skills. In this paper, a 3D virtual reality simulator for core skills training in minimally invasive surgery is presented. The system can generate realistic 3D vascular models segmented from patient datasets, including a beating heart, and provide a real-time computation of force and force feedback module for surgical simulation. Instruments, such as a catheter or guide wire, are represented by a multi-body mass-spring model. In addition, a realistic user interface with multiple windows and real-time 3D views are developed. Moreover, the simulator is also provided with a human-machine interaction module that gives doctors the sense of touch during the surgery training, enables them to control the motion of a virtual catheter/guide wire inside a complex vascular model. Experimental results show that the simulator is suitable for minimally invasive surgery training.

Accelerating an Ordered-Subset Low-Dose X-Ray Cone Beam Computed Tomography Image Reconstruction with a Power Factor and Total Variation Minimization

PubMed Central

Huang, Hsuan-Ming; Hsiao, Ing-Tsung

2016-01-01

In recent years, there has been increased interest in low-dose X-ray cone beam computed tomography (CBCT) in many fields, including dentistry, guided radiotherapy and small animal imaging. Despite reducing the radiation dose, low-dose CBCT has not gained widespread acceptance in routine clinical practice. In addition to performing more evaluation studies, developing a fast and high-quality reconstruction algorithm is required. In this work, we propose an iterative reconstruction method that accelerates ordered-subsets (OS) reconstruction using a power factor. Furthermore, we combine it with the total-variation (TV) minimization method. Both simulation and phantom studies were conducted to evaluate the performance of the proposed method. Results show that the proposed method can accelerate conventional OS methods, greatly increase the convergence speed in early iterations. Moreover, applying the TV minimization to the power acceleration scheme can further improve the image quality while preserving the fast convergence rate. PMID:27073853

Targeted tuberculosis contact investigation saves money without sacrificing health.

PubMed

Pisu, Maria; Gerald, Joe; Shamiyeh, James E; Bailey, William C; Gerald, Lynn B

2009-01-01

Health departments require an efficient strategy to investigate individuals exposed to Mycobacterium tuberculosis. The contact priority model (CPM) uses a decision rule to minimize testing of low-risk contacts; however, its impact on costs and disease control is unknown. A cost-effectiveness analysis compared the CPM with the traditional concentric circle approach (CCA) in a simulated population of 1000 healthy, community-dwelling adults with a 10% background rate of latent tuberculosis (TB) infection. The analysis was conducted from the perspective of the Alabama Department of Public Health. Model inputs were derived from the literature and the Alabama Department of Public Health. Lifetime costs (2004 dollars) and outcomes were discounted 3 percent annually. Incremental cost-effectiveness ratios were used to compare the strategies. Over the lifetime of 1000 simulated contacts, the CPM saved $45,000 but led to 0.5 additional TB cases and 0.24 fewer years of life. The CCA is more effective than the CPM, but it costs $92,934 to prevent one additional TB case and $185,920 to gain one additional life year. The CPM reduces costs with minimal loss of disease control and is a viable alternative to the CCA under most conditions.

A generic template for automated bioanalytical ligand-binding assays using modular robotic scripts in support of discovery biotherapeutic programs.

PubMed

Duo, Jia; Dong, Huijin; DeSilva, Binodh; Zhang, Yan J

2013-07-01

Sample dilution and reagent pipetting are time-consuming steps in ligand-binding assays (LBAs). Traditional automation-assisted LBAs use assay-specific scripts that require labor-intensive script writing and user training. Five major script modules were developed on Tecan Freedom EVO liquid handling software to facilitate the automated sample preparation and LBA procedure: sample dilution, sample minimum required dilution, standard/QC minimum required dilution, standard/QC/sample addition, and reagent addition. The modular design of automation scripts allowed the users to assemble an automated assay with minimal script modification. The application of the template was demonstrated in three LBAs to support discovery biotherapeutic programs. The results demonstrated that the modular scripts provided the flexibility in adapting to various LBA formats and the significant time saving in script writing and scientist training. Data generated by the automated process were comparable to those by manual process while the bioanalytical productivity was significantly improved using the modular robotic scripts.

The minimal axion minimal linear σ model

NASA Astrophysics Data System (ADS)

Merlo, L.; Pobbe, F.; Rigolin, S.

2018-05-01

The minimal SO(5) / SO(4) linear σ model is extended including an additional complex scalar field, singlet under the global SO(5) and the Standard Model gauge symmetries. The presence of this scalar field creates the conditions to generate an axion à la KSVZ, providing a solution to the strong CP problem, or an axion-like-particle. Different choices for the PQ charges are possible and lead to physically distinct Lagrangians. The internal consistency of each model necessarily requires the study of the scalar potential describing the SO(5)→ SO(4), electroweak and PQ symmetry breaking. A single minimal scenario is identified and the associated scalar potential is minimised including counterterms needed to ensure one-loop renormalizability. In the allowed parameter space, phenomenological features of the scalar degrees of freedom, of the exotic fermions and of the axion are illustrated. Two distinct possibilities for the axion arise: either it is a QCD axion with an associated scale larger than ˜ 105 TeV and therefore falling in the category of the invisible axions; or it is a more massive axion-like-particle, such as a 1 GeV axion with an associated scale of ˜ 200 TeV, that may show up in collider searches.

"Lull pgm System" for Autologous Fat Grafting: A Simple Closed System with Minimal Equipment and No Extra Cost.

PubMed

Morselli, Paolo Giovanni; Micai, Alessandro; Giorgini, Federico Armando

2016-08-01

The "Lull pgm system" is a closed system for purifying harvested fat. It processes the collected tissue safely without any additional cost. The system was conceived by referring to the targets described in the literature with the aim of creating a simple system that guarantees a high standard of purification and requires minimal equipment that is available in every operating room. Cost must be always considered: even the most prosperous hospitals must keep within tight annual budgets. "Lull" can be used instead of expensive devices or disposable kits, without substantially increasing the operating time. The system has been used in clinical practice for many plastic reconstructive procedures and has obtained positive results and patient satisfaction, and no contraindications or disadvantages have been observed.

Energy efficient engine low-pressure compressor component test hardware detailed design report

NASA Technical Reports Server (NTRS)

Michael, C. J.; Halle, J. E.

1981-01-01

The aerodynamic and mechanical design description of the low pressure compressor component of the Energy Efficient Engine were used. The component was designed to meet the requirements of the Flight Propulsion System while maintaining a low cost approach in providing a low pressure compressor design for the Integrated Core/Low Spool test required in the Energy Efficient Engine Program. The resulting low pressure compressor component design meets or exceeds all design goals with the exception of surge margin. In addition, the expense of hardware fabrication for the Integrated Core/Low Spool test has been minimized through the use of existing minor part hardware.

Intrauterine devices and other forms of contraception: thinking outside the pack.

PubMed

Allen, Caitlin; Kolehmainen, Christine

2015-05-01

A variety of contraception options are available in addition to traditional combined oral contraceptive pills. Newer long-acting reversible contraceptive (LARC) methods such as intrauterine devices and subcutaneous implants are preferred because they do not depend on patient compliance. They are highly effective and appropriate for most women. Female and male sterilization are other effective but they are irreversible and require counseling to minimize regret. The contraceptive injection, patch, and ring do not require daily administration, but their typical efficacy rates are lower than LARC methods and similar to those for combined oral contraceptive pills. Copyright © 2015 Elsevier Inc. All rights reserved.

Deep Space Gateway - Enabling Missions to Mars

NASA Technical Reports Server (NTRS)

Rucker, Michelle; Connolly, John

2017-01-01

There are many opportunities for commonality between Lunar vicinity and Mars mission hardware and operations. Best approach: Identify Mars mission risks that can be bought down with testing in the Lunar vicinity, then explore hardware and operational concepts that work for both missions with minimal compromise. Deep Space Transport will validate the systems and capabilities required to send humans to Mars orbit and return to Earth. Deep Space Gateway provides a convenient assembly, checkout, and refurbishment location to enable Mars missions Current deep space transport concept is to fly missions of increasing complexity: Shakedown cruise, Mars orbital mission, Mars surface mission; Mars surface mission would require additional elements.

Image guidance systems for minimally invasive sinus and skull base surgery in children.

PubMed

Benoit, Margo McKenna; Silvera, V Michelle; Nichollas, Richard; Jones, Dwight; McGill, Trevor; Rahbar, Reza

2009-10-01

The use of image guidance for sinonasal and skull base surgery has been well-characterized in adults but there is limited information on the use of these systems in the pediatric population, despite their widespread use. The aim of this study is to evaluate the use of image guidance systems to facilitate an endoscopic minimally invasive approach to sinonasal and skull base surgery in a pediatric population. A retrospective cohort study was performed at a tertiary pediatric hospital. Thirty-three children presented with complications of sinusitis, tumors, traumatic, or congenital lesions of the skull base and underwent endoscopic surgery using image guidance from March 2000 to April 2007. Patient variables including diagnosis, extent of disease, and complications were extracted from paper and computer charts. Additional surgical variables including set-up time, accuracy, surgeon satisfaction index and number of uses per case were also reviewed. Twenty-eight patients (85%) underwent sinonasal surgery and five (15%) underwent skull base surgery. Indications included infectious complications of acute sinusitis (N=15), neoplasms (N=12), choanal atresia (N=4), and cerebrospinal fluid leak (N=2). Thirty-one patients (94%) required only one procedure. No surgical complications were reported. Surgeon satisfaction, mean accuracy and number of uses per procedure increased over time (p<0.05). Image guidance systems are safe and effective tools that facilitate a minimally invasive approach to sinonasal and skull base surgery in children. Consistent with adult literature, usage and surgeon comfort increased with experience. The additional anatomical information obtained by image guidance systems facilitates a minimally invasive endoscopic approach for sinonasal and skull base pathologies.

Fast Algorithms for Designing Unimodular Waveform(s) With Good Correlation Properties

NASA Astrophysics Data System (ADS)

Li, Yongzhe; Vorobyov, Sergiy A.

2018-03-01

In this paper, we develop new fast and efficient algorithms for designing single/multiple unimodular waveforms/codes with good auto- and cross-correlation or weighted correlation properties, which are highly desired in radar and communication systems. The waveform design is based on the minimization of the integrated sidelobe level (ISL) and weighted ISL (WISL) of waveforms. As the corresponding optimization problems can quickly grow to large scale with increasing the code length and number of waveforms, the main issue turns to be the development of fast large-scale optimization techniques. The difficulty is also that the corresponding optimization problems are non-convex, but the required accuracy is high. Therefore, we formulate the ISL and WISL minimization problems as non-convex quartic optimization problems in frequency domain, and then simplify them into quadratic problems by utilizing the majorization-minimization technique, which is one of the basic techniques for addressing large-scale and/or non-convex optimization problems. While designing our fast algorithms, we find out and use inherent algebraic structures in the objective functions to rewrite them into quartic forms, and in the case of WISL minimization, to derive additionally an alternative quartic form which allows to apply the quartic-quadratic transformation. Our algorithms are applicable to large-scale unimodular waveform design problems as they are proved to have lower or comparable computational burden (analyzed theoretically) and faster convergence speed (confirmed by comprehensive simulations) than the state-of-the-art algorithms. In addition, the waveforms designed by our algorithms demonstrate better correlation properties compared to their counterparts.

Case outsourcing medical device reprocessing.

PubMed

Haley, Deborah

2004-04-01

IN THE INTEREST OF SAVING MONEY, many hospitals are considering extending the life of some single-use medical devices by using medical device reprocessing programs. FACILITIES OFTEN LACK the resources required to meet the US Food and Drug Administration's tough quality assurance standards. BY OUTSOURCING, hospitals can reap the benefits of medical device reprocessing without assuming additional staffing and compliance burdens. OUTSOURCING enables hospitals to implement a medical device reprocessing program quickly, with no capital investment and minimal effort.

The Role of a Conservative Minimal Interventional Management Protocol in the Fractures of the Dentate Portion of the Adult Mandible

PubMed Central

Krishnan, Balasubramanian

2015-01-01

Mandibular fractures are commonly encountered by the maxillofacial surgeon. Maxillomandibular fixation (MMF) and open reduction and internal fixation (ORIF), or a combination of both, are the accepted standard treatments. This study aims to assess the role of a conservative minimal intervention protocol in the management of undisplaced/minimally displaced fractures of the dentate portion of the adult mandible and the complications associated with such minimalistic intervention. Thirty-four patients with undisplaced/minimally displaced fractures of the dentate portion of the adult mandible were advised to restrict mouth opening and limit themselves to a soft diet for a minimum of 4 weeks. All patients were advised follow-up at regular intervals for at least 3 months. Five patients were lost to follow-up. Symphysis and parasymphysis fractures were the most common fracture locations. Fourteen patients needed tension band stabilization with a mandibular arch bar/bridle wiring and three patients required extraction of luxated teeth. All patients showed satisfactory healing except three in whom additional intervention (ORIF) was performed. The improvement in mouth opening was statistically significant. Complications were seen more frequently among smokers and alcoholics. For patients with minimally displaced mandibular fractures, it is necessary to consider if the perceived benefits of intervention justify the associated added costs and possible complications. Patients have to be fully informed about the possible complications while using this minimal intervention protocol. This study concludes that a conservative minimal intervention management protocol for such fractures of the dentate portion of the mandible can produce satisfactory results. PMID:26889344

Safety policy and requirements for payloads using the Space Transportation System (STS)

NASA Technical Reports Server (NTRS)

1982-01-01

The Space Transportation Operations (STO) safety policy is to minimize STO involvement in the payload and its GSE (ground support equipment) design process while maintaining the assurance of a safe operation. Requirements for assuring payload mission success are the responsibility of the payload organization and are beyond the scope of this document. The intent is to provide the overall safety policies and requirements while allowing for negotiation between the payload organization and the STO operator in the method of implementation of payload safety. This revision provides for a relaxation in the monitoring requirements for inhibits, allows the payload organization to pursue design options and reflects, additionally, some new requirements. As of the issue date of this NHB, payloads which have completed the formal safety assessment reviews of their preliminary design on the basis of the May 1979 issue will be reassessed for compliance with the above changes.

Awake craniotomy for microsurgical obliteration of mycotic aneurysms: technical report of three cases.

PubMed

Lüders, Jürgen C; Steinmetz, Michael P; Mayberg, Marc R

2005-01-01

Infectious (mycotic) aneurysms that do not resolve with medical treatment require surgical obliteration, usually requiring sacrifice of the parent artery. In addition, patients with mycotic aneurysms frequently need subsequent cardiac valve repair, which often necessitates anticoagulation. Three cases of awake craniotomy for microsurgical clipping of mycotic aneurysms are presented. Awake minimally invasive craniotomy using frameless stereotactic guidance on the basis of computed tomographic angiography enables temporary occlusion of the parent artery with neurological assessment before obliteration of the aneurysm. A 56-year-old woman presented with progressively worsening mitral valve disease and a history of subacute bacterial endocarditis and subarachnoid hemorrhage 30 years previously. A cerebral angiogram revealed a 4-mm left middle cerebral artery (MCA) angular branch aneurysm, which required obliteration before mitral valve replacement. The second patient, a 64-year-old woman with a history of rheumatic fever, had an 8-mm right distal MCA aneurysm diagnosed in the setting of pulmonary abscess and worsening cardiac function as a result of mitral valve disease. The third patient, a 57-year-old man with a history of fevers, night sweats, and progressive mitral valve disease, had an enlarging left MCA angular branch aneurysm despite the administration of antibiotics. Because of their location on distal MCA branches, none of the aneurysms were amenable to preoperative test balloon occlusion. After undergoing stereotactic computed tomographic angiography with fiducial markers, the patients underwent a minimally invasive awake craniotomy with frameless stereotactic navigation. In all cases, the results of the neurological examination were unchanged during temporary parent artery occlusion and the aneurysms were successfully obliterated. Awake minimally invasive craniotomy for an infectious aneurysm located in eloquent brain enables awake testing before permanent clipping or vessel sacrifice. Combining frameless stereotactic navigation with computed tomographic angiography allowed us to perform the operation quickly through a small craniotomy with minimal exploration.

Effects of tools inserted through snake-like surgical manipulators.

PubMed

Murphy, Ryan J; Otake, Yoshito; Wolfe, Kevin C; Taylor, Russell H; Armand, Mehran

2014-01-01

Snake-like manipulators with a large, open lumen can offer improved treatment alternatives for minimally-and less-invasive surgeries. In these procedures, surgeons use the manipulator to introduce and control flexible tools in the surgical environment. This paper describes a predictive algorithm for estimating manipulator configuration given tip position for nonconstant curvature, cable-driven manipulators using energy minimization. During experimental bending of the manipulator with and without a tool inserted in its lumen, images were recorded from an overhead camera in conjunction with actuation cable tension and length. To investigate the accuracy, the estimated manipulator configuration from the model and the ground-truth configuration measured from the image were compared. Additional analysis focused on the response differences for the manipulator with and without a tool inserted through the lumen. Results indicate that the energy minimization model predicts manipulator configuration with an error of 0.24 ± 0.22mm without tools in the lumen and 0.24 ± 0.19mm with tools in the lumen (no significant difference, p = 0.81). Moreover, tools did not introduce noticeable perturbations in the manipulator trajectory; however, there was an increase in requisite force required to reach a configuration. These results support the use of the proposed estimation method for calculating the shape of the manipulator with an tool inserted in its lumen when an accuracy range of at least 1mm is required.

A robust motion estimation system for minimal invasive laparoscopy

NASA Astrophysics Data System (ADS)

Marcinczak, Jan Marek; von Öhsen, Udo; Grigat, Rolf-Rainer

2012-02-01

Laparoscopy is a reliable imaging method to examine the liver. However, due to the limited field of view, a lot of experience is required from the surgeon to interpret the observed anatomy. Reconstruction of organ surfaces provide valuable additional information to the surgeon for a reliable diagnosis. Without an additional external tracking system the structure can be recovered from feature correspondences between different frames. In laparoscopic images blurred frames, specular reflections and inhomogeneous illumination make feature tracking a challenging task. We propose an ego-motion estimation system for minimal invasive laparoscopy that can cope with specular reflection, inhomogeneous illumination and blurred frames. To obtain robust feature correspondence, the approach combines SIFT and specular reflection segmentation with a multi-frame tracking scheme. The calibrated five-point algorithm is used with the MSAC robust estimator to compute the motion of the endoscope from multi-frame correspondence. The algorithm is evaluated using endoscopic videos of a phantom. The small incisions and the rigid endoscope limit the motion in minimal invasive laparoscopy. These limitations are considered in our evaluation and are used to analyze the accuracy of pose estimation that can be achieved by our approach. The endoscope is moved by a robotic system and the ground truth motion is recorded. The evaluation on typical endoscopic motion gives precise results and demonstrates the practicability of the proposed pose estimation system.

Role for a region of helically unstable DNA within the Epstein-Barr virus latent cycle origin of DNA replication oriP in origin function

DOE Office of Scientific and Technical Information (OSTI.GOV)

Polonskaya, Zhanna; Benham, Craig J.; Hearing, Janet

The minimal replicator of the Epstein-Barr virus (EBV) latent cycle origin of DNA replication oriP is composed of two binding sites for the Epstein-Barr virus nuclear antigen-1 (EBNA-1) and flanking inverted repeats that bind the telomere repeat binding factor TRF2. Although not required for minimal replicator activity, additional binding sites for EBNA-1 and TRF2 and one or more auxiliary elements located to the right of the EBNA-1/TRF2 sites are required for the efficient replication of oriP plasmids. Another region of oriP that is predicted to be destabilized by DNA supercoiling is shown here to be an important functional component ofmore » oriP. The ability of DNA fragments of unrelated sequence and possessing supercoiled-induced DNA duplex destabilized (SIDD) structures, but not fragments characterized by helically stable DNA, to substitute for this component of oriP demonstrates a role for the SIDD region in the initiation of oriP-plasmid DNA replication.« less

Membrane thickening aerobic digestion processes.

PubMed

Woo, Bryen

2014-01-01

Sludge management accounts for approximately 60% of the total wastewater treatment plant expenditure and laws for sludge disposal are becoming increasingly stringent, therefore much consideration is required when designing a solids handling process. A membrane thickening aerobic digestion process integrates a controlled aerobic digestion process with pre-thickening waste activated sludge using membrane technology. This process typically features an anoxic tank, an aerated membrane thickener operating in loop with a first-stage digester followed by second-stage digestion. Membrane thickening aerobic digestion processes can handle sludge from any liquid treatment process and is best for facilities obligated to meet low total phosphorus and nitrogen discharge limits. Membrane thickening aerobic digestion processes offer many advantages including: producing a reusable quality permeate with minimal levels of total phosphorus and nitrogen that can be recycled to the head works of a plant, protecting the performance of a biological nutrient removal liquid treatment process without requiring chemical addition, providing reliable thickening up to 4% solids concentration without the use of polymers or attention to decanting, increasing sludge storage capacities in existing tanks, minimizing the footprint of new tanks, reducing disposal costs, and providing Class B stabilization.

Optimal Design of Functionally Graded Metallic Foam Insulations

NASA Technical Reports Server (NTRS)

Haftka, Raphael T.; Sankar, Bhavani; Venkataraman, Satchi; Zhu, Huadong

2002-01-01

The focus of our work has been on developing an insight into the physics that govern the optimum design of thermal insulation for use in thermal protection systems of launch vehicle. Of particular interest was to obtain optimality criteria for designing foam insulations that have density (or porosity) distributions through the thickness for optimum thermal performance. We investigate the optimum design of functionally graded thermal insulation for steady state heat transfer through the foam. We showed that the heat transfer in the foam has competing modes, of radiation and conduction. The problem assumed a fixed inside temperature of 400 K and varied the aerodynamic surface heating on the outside surface from 0.2 to 1.0 MW/sq m. The thermal insulation develops a high temperature gradient through the thickness. Investigation of the model developed for heat conduction in foams showed that at high temperatures (as on outside wall) intracellular radiation dominates the heat transfer in the foam. Minimizing radiation requires reducing the pore size, which increases the density of the foam. At low temperatures (as on the inside wall), intracellular conduction (of the metal and air) dominates the heat transfer. Minimizing conduction requires increasing the pore size. This indicated that for every temperature there was an optimum value of density that minimized the heat transfer coefficient. Two optimization studies were performed. One was to minimize the heat transmitted though a fixed thickness insulation by varying density profiles. The second was to obtain the minimum mass insulation for specified thickness. Analytical optimality criteria were derived for the cases considered. The optimality condition for minimum heat transfer required that at each temperature we find the density that minimizes the heat transfer coefficient. Once a relationship between the optimum heat transfer coefficient and the temperature was found, the design problem reduced to the solution of a simple nonlinear differential equation. Preliminary results of this work were presented at the American Society of Composites meeting, and the final version was submitted for publication in the AIAA Journal. In addition to minimizing the transmitted heat, we investigated the optimum design for minimum weight given an acceptable level of heat transmission through the insulation. The optimality criterion developed was different from that obtained for minimizing beat transfer coefficient. For minimum mass design, we had to find for a given temperature the optimum density, which minimized the logarithmic derivative of the insulation thermal conductivity with respect to its density. The logarithmic derivative is defined as the ratio of relative change in the dependent response (thermal conductivity) to the relative change in the independent variable (density). The results have been documented as a conference paper that will be presented at the upcoming AIAA.

AMMOS2: a web server for protein-ligand-water complexes refinement via molecular mechanics.

PubMed

Labbé, Céline M; Pencheva, Tania; Jereva, Dessislava; Desvillechabrol, Dimitri; Becot, Jérôme; Villoutreix, Bruno O; Pajeva, Ilza; Miteva, Maria A

2017-07-03

AMMOS2 is an interactive web server for efficient computational refinement of protein-small organic molecule complexes. The AMMOS2 protocol employs atomic-level energy minimization of a large number of experimental or modeled protein-ligand complexes. The web server is based on the previously developed standalone software AMMOS (Automatic Molecular Mechanics Optimization for in silico Screening). AMMOS utilizes the physics-based force field AMMP sp4 and performs optimization of protein-ligand interactions at five levels of flexibility of the protein receptor. The new version 2 of AMMOS implemented in the AMMOS2 web server allows the users to include explicit water molecules and individual metal ions in the protein-ligand complexes during minimization. The web server provides comprehensive analysis of computed energies and interactive visualization of refined protein-ligand complexes. The ligands are ranked by the minimized binding energies allowing the users to perform additional analysis for drug discovery or chemical biology projects. The web server has been extensively tested on 21 diverse protein-ligand complexes. AMMOS2 minimization shows consistent improvement over the initial complex structures in terms of minimized protein-ligand binding energies and water positions optimization. The AMMOS2 web server is freely available without any registration requirement at the URL: http://drugmod.rpbs.univ-paris-diderot.fr/ammosHome.php. © The Author(s) 2017. Published by Oxford University Press on behalf of Nucleic Acids Research.

AMMOS2: a web server for protein–ligand–water complexes refinement via molecular mechanics

PubMed Central

Labbé, Céline M.; Pencheva, Tania; Jereva, Dessislava; Desvillechabrol, Dimitri; Becot, Jérôme; Villoutreix, Bruno O.; Pajeva, Ilza

2017-01-01

Abstract AMMOS2 is an interactive web server for efficient computational refinement of protein–small organic molecule complexes. The AMMOS2 protocol employs atomic-level energy minimization of a large number of experimental or modeled protein–ligand complexes. The web server is based on the previously developed standalone software AMMOS (Automatic Molecular Mechanics Optimization for in silico Screening). AMMOS utilizes the physics-based force field AMMP sp4 and performs optimization of protein–ligand interactions at five levels of flexibility of the protein receptor. The new version 2 of AMMOS implemented in the AMMOS2 web server allows the users to include explicit water molecules and individual metal ions in the protein–ligand complexes during minimization. The web server provides comprehensive analysis of computed energies and interactive visualization of refined protein–ligand complexes. The ligands are ranked by the minimized binding energies allowing the users to perform additional analysis for drug discovery or chemical biology projects. The web server has been extensively tested on 21 diverse protein–ligand complexes. AMMOS2 minimization shows consistent improvement over the initial complex structures in terms of minimized protein–ligand binding energies and water positions optimization. The AMMOS2 web server is freely available without any registration requirement at the URL: http://drugmod.rpbs.univ-paris-diderot.fr/ammosHome.php. PMID:28486703

Interprofessional student clinics: an economic evaluation of collaborative clinical placement education.

PubMed

Haines, Terry P; Kent, Fiona; Keating, Jennifer L

2014-07-01

Interprofessional student clinics can be used to create clinical education placements for health professional students in addition to traditional hospital-based placements and present an opportunity to provide interprofessional learning experiences in a clinical context. To date, little consideration has been given in research literature as to whether such clinics are economically viable for a university to run. We conducted an economic evaluation based upon data generated during a pilot of an interprofessional student clinic based in Australia. Cost-minimization analyses of the student clinic as opposed to traditional profession-specific clinical education in hospitals were conducted from university, Commonwealth Government, state government and societal perspectives. Cost data gathered during the pilot study and market prices were used where available, while $AUD currency at 2011 values were used. Per student day of clinical education, the student clinic cost an additional $289, whereas the state government saved $49 and the Commonwealth Government saved $66. Overall, society paid an additional $175 per student day of clinical education using the student clinic as opposed to conventional hospital-based placements, indicating that traditional hospital-based placements are a cost-minimizing approach overall for providing clinical education. Although interprofessional student clinics have reported positive patient and student learning outcomes, further research is required to determine if these benefits can justify the additional cost of this model of education. Considerations for clinic sustainability are proposed.

An Analysis of Tank Gap in Military Balance between Republic of Korea and North Korea

DTIC Science & Technology

1989-12-01

designation *1100-3B CD850-6 CD850-6A Type hydrokinetic crossdrive No. of gears (forward/reverse) 4/2 2/2 2/1 Steering system hydrostatic crossdrive hydro...increased the number of bombers supplied to NK, and by 1956 they had introduced a new aircraft weapon system , the MIG-17 fighters. The agreement stood...U.S. inventories. Additionally, these arms were single weapons (as opposed to weapons systems ) which required only minimal mainte- nance and limited

Grumman evaluates Space Station thermal control and power systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kandebo, S.W.

1985-09-01

Attention is given to the definition of requirements for the NASA Space Station's electrical power and thermal control systems, which must be highly dependable to minimize the need for external support and will embody a highly flexible modular design concept. Module maintenance will be performed by in-orbit replacement of failed modules, and energy storage system growth will be accomplished by the incorporation of additional modules. Both photovoltaic and solar heat-driven electrical generator concepts are under consideration as the basis of the power system.

Consequences of an Abelian family symmetry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ramond, P.

1996-01-01

The addition of an Abelian family symmetry to the Minimal Super-symmetric Standard Model reproduces the observed hierarchies of quark and lepton masses and quark mixing angles, only if it is anomalous. Green-Schwarz compensation of its anomalies requires the electroweak mixing angle to be sin{sup 2}{theta}{sub {omega}} = 3/8 at the string scale, without any assumed GUT structure, suggesting a superstring origin for the standard model. The analysis is extended to neutrino masses and the lepton mixing matrix.

Directions for model building from asymptotic safety

NASA Astrophysics Data System (ADS)

Bond, Andrew D.; Hiller, Gudrun; Kowalska, Kamila; Litim, Daniel F.

2017-08-01

Building on recent advances in the understanding of gauge-Yukawa theories we explore possibilities to UV-complete the Standard Model in an asymptotically safe manner. Minimal extensions are based on a large flavor sector of additional fermions coupled to a scalar singlet matrix field. We find that asymptotic safety requires fermions in higher representations of SU(3) C × SU(2) L . Possible signatures at colliders are worked out and include R-hadron searches, diboson signatures and the evolution of the strong and weak coupling constants.

Rapid HIV RNA rebound after antiretroviral treatment interruption in persons durably suppressed in Fiebig I acute HIV infection.

PubMed

Colby, Donn J; Trautmann, Lydie; Pinyakorn, Suteeraporn; Leyre, Louise; Pagliuzza, Amélie; Kroon, Eugène; Rolland, Morgane; Takata, Hiroshi; Buranapraditkun, Supranee; Intasan, Jintana; Chomchey, Nitiya; Muir, Roshell; Haddad, Elias K; Tovanabutra, Sodsai; Ubolyam, Sasiwimol; Bolton, Diane L; Fullmer, Brandie A; Gorelick, Robert J; Fox, Lawrence; Crowell, Trevor A; Trichavaroj, Rapee; O'Connell, Robert; Chomont, Nicolas; Kim, Jerome H; Michael, Nelson L; Robb, Merlin L; Phanuphak, Nittaya; Ananworanich, Jintanat

2018-06-11

Antiretroviral therapy during the earliest stage of acute HIV infection (Fiebig I) might minimize establishment of a latent HIV reservoir and thereby facilitate viremic control after analytical treatment interruption. We show that 8 participants, who initiated treatment during Fiebig I and were treated for a median of 2.8 years, all experienced rapid viral load rebound following analytical treatment interruption, indicating that additional strategies are required to control or eradicate HIV.

Epileptogenicity and pathology - Under consideration of ablative approaches.

PubMed

Stefan, H; Schmitt, F C

2018-05-01

Besides resective epilepsy surgery, minimally invasive ablation using new diagnostic and therapeutic techniques recently became available. Optimal diagnostic approaches for these treatment options are discussed. The pathophysiology of epileptogenic networks differs depending on the lesion-types and location, requiring a differential use of non-invasive or invasive functional studies. In addition to the definition of epileptogenic zones, a challenge for pre-surgical investigation is the determination of three-dimensional epileptic networks to be removed. Copyright © 2018. Published by Elsevier B.V.

The clockwork supergravity

NASA Astrophysics Data System (ADS)

Kehagias, Alex; Riotto, Antonio

2018-02-01

We show that the minimal D = 5, N = 2 gauged supergravity set-up may encode naturally the recently proposed clockwork mechanism. The minimal embedding requires one vector multiplet in addition to the supergravity multiplet and the clockwork scalar is identified with the scalar in the vector multiplet. The scalar has a two-parameter potential and it can accommodate the clockwork, the Randall-Sundrum and a no-scale model with a flat potential, depending on the values of the parameters. The continuous clockwork background breaks half of the original supersymmetries, leaving a D = 4, N = 1 theory on the boundaries. We also show that the generated hierarchy by the clockwork is not exponential but rather power law. The reason is that four-dimensional Planck scale has a power-law dependence on the compactification radius, whereas the corresponding KK spectrum depends on the logarithm of the latter.

Gauged lepton flavour

DOE PAGES

Alonso, Rodrigo; Fernandez Martinez, Enrique; Gavela, M. B.; ...

2016-12-22

The gauging of the lepton flavour group is considered in the Standard Model context and in its extension with three right-handed neutrinos. The anomaly cancellation conditions lead to a Seesaw mechanism as underlying dynamics for all leptons; in addition, it requires a phenomenologically viable setup which leads to Majorana masses for the neutral sector: the type I Seesaw Lagrangian in the Standard Model case and the inverse Seesaw in the extended model. Within the minimal extension of the scalar sector, the Yukawa couplings are promoted to scalar fields in the bifundamental of the flavour group. The resulting low-energy Yukawa couplingsmore » are proportional to inverse powers of the vacuum expectation values of those scalars; the protection against flavour changing neutral currents differs from that of Minimal Flavour Violation. In every case, the μ - τ flavour sector exhibits rich and promising phenomenological signals.« less

Programmable Differential Delay Circuit With Fine Delay Adjustment

DOEpatents

DeRyckere, John F.; Jenkins, Philip Nord; Cornett, Frank Nolan

2002-07-09

Circuitry that provides additional delay to early arriving signals such that all data signals arrive at a receiving latch with same path delay. The delay of a forwarded clock reference is also controlled such that the capturing clock edge will be optimally positioned near quadrature (depending on latch setup/hold requirements). The circuitry continuously adapts to data and clock path delay changes and digital filtering of phase measurements reduce errors brought on by jittering data edges. The circuitry utilizes only the minimum amount of delay necessary to achieve objective thereby limiting any unintended jitter. Particularly, this programmable differential delay circuit with fine delay adjustment is designed to allow the skew between ASICS to be minimized. This includes skew between data bits, between data bits and clocks as well as minimizing the overall skew in a channel between ASICS.

Minimal state-dependent proof of measurement contextuality for a qubit

NASA Astrophysics Data System (ADS)

Kunjwal, Ravi; Ghosh, Sibasish

2014-04-01

We show that three unsharp binary qubit measurements are enough to violate a generalized noncontextuality inequality, the Liang-Spekkens-Wiseman inequality, in a state-dependent manner. For the case of trine spin axes we calculate the optimal quantum violation of this inequality. In addition, we show that unsharp qubit measurements do not allow a state-independent violation of this inequality. We thus provide a minimal state-dependent proof of measurement contextuality requiring one qubit and three unsharp measurements. Our result rules out generalized noncontextual models of these measurements which were previously conjectured to exist. More importantly, this class of generalized noncontextual models includes the traditional Kochen-Specker (KS) noncontextual models as a proper subset, so our result rules out a larger class of models than those ruled out by a violation of the corresponding KS inequality in this scenario.

Environmental fate and effects of the lampricide TFM: a review

USGS Publications Warehouse

Hubert, T.D.

2003-01-01

Use of 3-trifluoromethyl-4-nitrophenol (TFM) is limited geographically to the Great Lakes basin where it is the principal agent used in control of the sea lamprey (Petromyzon marinus). It is clear from available data that TFM has effects on the environment, but the effects reported are transient. Individual organisms and aquatic communities return to pretreatment conditions after lampricide treatments have concluded. TFM is not persistent, is detoxified, and presents minimal long-term toxicological risk. TFM is relatively nontoxic to mammals. Treatment levels do not pose a threat to wildlife. However, TFM is an estrogen agonist and additional testing to define the nature and magnitude of this effect will likely be required. Because stream treatments are done on 3 to 5 year cycles, and exposures are limited to approximately 12 h, minimal risk to aquatic organisms is expected.

Environmental fate and effects of the lampricide TFM: A review

USGS Publications Warehouse

Hubert, T.D.

2003-01-01

Use of 3-trifluoromethyl-4-nitrophenol (TFM) is limited geographically to the Great Lakes basin where it is the principal agent used in control of the sea lamprey (Petromyzon marinus). It is clear from available data that TFM has effects on the environment, but the effects reported are transient. Individual organisms and aquatic communities return to pretreatment conditions after lampricide treatments have concluded. TFM is not persistent, is detoxified, and presents minimal long-term toxicological risk. TFM is relatively nontoxic to mammals. Treatment levels do not pose a threat to wildlife. However, TFM is an estrogen agonist and additional testing to define the nature and magnitude of this effect will likely be required. Because stream treatments are done on 3 to 5 year cycles, and exposures are limited to approximately 12 h, minimal risk to aquatic organisms is expected.

One-kilohertz eye tracker and active intraoperative torsion detection in the NIDEK CXIII and Quest excimer lasers.

PubMed

Waring, George O

2009-10-01

To describe recent technological additions to the NIDEK CXIII and Quest excimer lasers. A summary article with data from previous published studies outlining the benefits of newer technology. The addition of a 1-kHz infrared eye tracker decreased the spread of laser spot placement from a mean of 228.79 microm without a tracker to 38.47 microm with the eye tracker. The addition of real-time torsion error correction produced a statistically significantly lower cylinder dispersion, mean manifest refractive cylinder, and error of angle postoperatively in eyes that underwent LASIK. The incorporation of an ultrahigh speed eye tracker and active cyclotorsion correction surpasses the minimal technology criteria required for accurate wavefront-based ablations. Copyright 2009, SLACK Incorporated.

Sensor and computing resource management for a small satellite

NASA Astrophysics Data System (ADS)

Bhatia, Abhilasha; Goehner, Kyle; Sand, John; Straub, Jeremy; Mohammad, Atif; Korvald, Christoffer; Nervold, Anders Kose

A small satellite in a low-Earth orbit (e.g., approximately a 300 to 400 km altitude) has an orbital velocity in the range of 8.5 km/s and completes an orbit approximately every 90 minutes. For a satellite with minimal attitude control, this presents a significant challenge in obtaining multiple images of a target region. Presuming an inclination in the range of 50 to 65 degrees, a limited number of opportunities to image a given target or communicate with a given ground station are available, over the course of a 24-hour period. For imaging needs (where solar illumination is required), the number of opportunities is further reduced. Given these short windows of opportunity for imaging, data transfer, and sending commands, scheduling must be optimized. In addition to the high-level scheduling performed for spacecraft operations, payload-level scheduling is also required. The mission requires that images be post-processed to maximize spatial resolution and minimize data transfer (through removing overlapping regions). The payload unit includes GPS and inertial measurement unit (IMU) hardware to aid in image alignment for the aforementioned. The payload scheduler must, thus, split its energy and computing-cycle budgets between determining an imaging sequence (required to capture the highly-overlapping data required for super-resolution and adjacent areas required for mosaicking), processing the imagery (to perform the super-resolution and mosaicking) and preparing the data for transmission (compressing it, etc.). This paper presents an approach for satellite control, scheduling and operations that allows the cameras, GPS and IMU to be used in conjunction to acquire higher-resolution imagery of a target region.

Choosing colors for map display icons using models of visual search.

PubMed

Shive, Joshua; Francis, Gregory

2013-04-01

We show how to choose colors for icons on maps to minimize search time using predictions of a model of visual search. The model analyzes digital images of a search target (an icon on a map) and a search display (the map containing the icon) and predicts search time as a function of target-distractor color distinctiveness and target eccentricity. We parameterized the model using data from a visual search task and performed a series of optimization tasks to test the model's ability to choose colors for icons to minimize search time across icons. Map display designs made by this procedure were tested experimentally. In a follow-up experiment, we examined the model's flexibility to assign colors in novel search situations. The model fits human performance, performs well on the optimization tasks, and can choose colors for icons on maps with novel stimuli to minimize search time without requiring additional model parameter fitting. Models of visual search can suggest color choices that produce search time reductions for display icons. Designers should consider constructing visual search models as a low-cost method of evaluating color assignments.

Development of Carbon Dioxide Removal Systems for NASA's Deep Space Human Exploration Missions 2016-2017

NASA Technical Reports Server (NTRS)

Knox, James C.

2017-01-01

NASA has embarked on an endeavor that will enable humans to explore deep space, with the ultimate goal of sending humans to Mars. This journey will require significant developments in a wide range of technical areas, as resupply is unavailable in the Mars transit phase and early return is not possible. Additionally, mass, power, volume, and other resources must be minimized for all subsystems to reduce propulsion needs. Among the critical areas identified for development are life support systems, which will require increases in reliability and reductions in resources. This paper discusses current and planned developments in the area of carbon dioxide removal to support crewed Mars-class missions.

Design and manufacturing of the CFRP lightweight telescope structure

NASA Astrophysics Data System (ADS)

Stoeffler, Guenter; Kaindl, Rainer

2000-06-01

Design of earthbound telescopes is normally based on conventional steel constructions. Several years ago thermostable CFRP Telescope and reflector structures were developed and manufacturing for harsh terrestrial environments. The airborne SOFIA TA requires beyond thermostability an excessive stiffness to mass ratio for the structure fulfilling performance and not to exceed mass limitations by the aircraft Boeing 747 SP. Additional integration into A/C drives design of structure subassemblies. Thickness of CFRP Laminates, either filament wound or prepreg manufactured need special attention and techniques to gain high material quality according to aerospace requirements. Sequential shop assembly of the structure subassemblies minimizes risk for assembling TA. Design goals, optimization of layout and manufacturing techniques and results are presented.

Sensor Data Qualification System (SDQS) Implementation Study

NASA Technical Reports Server (NTRS)

Wong, Edmond; Melcher, Kevin; Fulton, Christopher; Maul, William

2009-01-01

The Sensor Data Qualification System (SDQS) is being developed to provide a sensor fault detection capability for NASA s next-generation launch vehicles. In addition to traditional data qualification techniques (such as limit checks, rate-of-change checks and hardware redundancy checks), SDQS can provide augmented capability through additional techniques that exploit analytical redundancy relationships to enable faster and more sensitive sensor fault detection. This paper documents the results of a study that was conducted to determine the best approach for implementing a SDQS network configuration that spans multiple subsystems, similar to those that may be implemented on future vehicles. The best approach is defined as one that most minimizes computational resource requirements without impacting the detection of sensor failures.

Minimizing transient influence in WHPA delineation: An optimization approach for optimal pumping rate schemes

NASA Astrophysics Data System (ADS)

Rodriguez-Pretelin, A.; Nowak, W.

2017-12-01

For most groundwater protection management programs, Wellhead Protection Areas (WHPAs) have served as primarily protection measure. In their delineation, the influence of time-varying groundwater flow conditions is often underestimated because steady-state assumptions are commonly made. However, it has been demonstrated that temporary variations lead to significant changes in the required size and shape of WHPAs. Apart from natural transient groundwater drivers (e.g., changes in the regional angle of flow direction and seasonal natural groundwater recharge), anthropogenic causes such as transient pumping rates are of the most influential factors that require larger WHPAs. We hypothesize that WHPA programs that integrate adaptive and optimized pumping-injection management schemes can counter transient effects and thus reduce the additional areal demand in well protection under transient conditions. The main goal of this study is to present a novel management framework that optimizes pumping schemes dynamically, in order to minimize the impact triggered by transient conditions in WHPA delineation. For optimizing pumping schemes, we consider three objectives: 1) to minimize the risk of pumping water from outside a given WHPA, 2) to maximize the groundwater supply and 3) to minimize the involved operating costs. We solve transient groundwater flow through an available transient groundwater and Lagrangian particle tracking model. The optimization problem is formulated as a dynamic programming problem. Two different optimization approaches are explored: I) the first approach aims for single-objective optimization under objective (1) only. The second approach performs multiobjective optimization under all three objectives where compromise pumping rates are selected from the current Pareto front. Finally, we look for WHPA outlines that are as small as possible, yet allow the optimization problem to find the most suitable solutions.

Uropathogenic Escherichia coli Metabolite-Dependent Quiescence and Persistence May Explain Antibiotic Tolerance during Urinary Tract Infection

PubMed Central

Leatham-Jensen, Mary P.; Mokszycki, Matthew E.; Rowley, David C.; Deering, Robert; Camberg, Jodi L.; Sokurenko, Evgeni V.; Tchesnokova, Veronika L.; Frimodt-Møller, Jakob; Leth Nielsen, Karen; Sun, Gongqin

2016-01-01

ABSTRACT In the present study, it is shown that although Escherichia coli CFT073, a human uropathogenic (UPEC) strain, grows in liquid glucose M9 minimal medium, it fails to grow on glucose M9 minimal medium agar plates seeded with ≤106 CFU. The cells on glucose plates appear to be in a “quiescent” state that can be prevented by various combinations of lysine, methionine, and tyrosine. Moreover, the quiescent state is characteristic of ~80% of E. coli phylogenetic group B2 multilocus sequence type 73 strains, as well as 22.5% of randomly selected UPEC strains isolated from community-acquired urinary tract infections in Denmark. In addition, E. coli CFT073 quiescence is not limited to glucose but occurs on agar plates containing a number of other sugars and acetate as sole carbon sources. It is also shown that a number of E. coli CFT073 mini-Tn5 metabolic mutants (gnd, gdhA, pykF, sdhA, and zwf) are nonquiescent on glucose M9 minimal agar plates and that quiescence requires a complete oxidative tricarboxylic acid (TCA) cycle. In addition, evidence is presented that, although E. coli CFT073 quiescence and persistence in the presence of ampicillin are alike in that both require a complete oxidative TCA cycle and each can be prevented by amino acids, E. coli CFT073 quiescence occurs in the presence or absence of a functional rpoS gene, whereas maximal persistence requires a nonfunctional rpoS. Our results suggest that interventions targeting specific central metabolic pathways may mitigate UPEC infections by interfering with quiescence and persistence. IMPORTANCE Recurrent urinary tract infections (UTIs) affect 10 to 40% of women. In up to 77% of those cases, the recurrent infections are caused by the same uropathogenic E. coli (UPEC) strain that caused the initial infection. Upon infection of urothelial transitional cells in the bladder, UPEC appear to enter a nongrowing quiescent intracellular state that is thought to serve as a reservoir responsible for recurrent UTIs. Here, we report that many UPEC strains enter a quiescent state when ≤106 CFU are seeded on glucose M9 minimal medium agar plates and show that mutations in several genes involved in central carbon metabolism prevent quiescence, as well as persistence, possibly identifying metabolic pathways involved in UPEC quiescence and persistence in vivo. PMID:27303698

DATA QUALITY OBJECTIVES FOR SELECTING WASTE SAMPLES FOR THE BENCH STEAM REFORMER TEST

DOE Office of Scientific and Technical Information (OSTI.GOV)

BANNING DL

2010-08-03

This document describes the data quality objectives to select archived samples located at the 222-S Laboratory for Fluid Bed Steam Reformer testing. The type, quantity and quality of the data required to select the samples for Fluid Bed Steam Reformer testing are discussed. In order to maximize the efficiency and minimize the time to treat Hanford tank waste in the Waste Treatment and Immobilization Plant, additional treatment processes may be required. One of the potential treatment processes is the fluid bed steam reformer (FBSR). A determination of the adequacy of the FBSR process to treat Hanford tank waste is required.more » The initial step in determining the adequacy of the FBSR process is to select archived waste samples from the 222-S Laboratory that will be used to test the FBSR process. Analyses of the selected samples will be required to confirm the samples meet the testing criteria.« less

Determining minimal display element requirements for surface map displays

DOT National Transportation Integrated Search

2003-04-14

There is a great deal of interest in developing electronic surface map displays to enhance safety and reduce incidents and incursions on or near the airport surface. There is a lack of research, however, detailing the minimal display elements require...

Channel access schemes and fiber optic configurations for integrated-services local area networks

NASA Astrophysics Data System (ADS)

Nassehi, M. Mehdi

1987-03-01

Local Area Networks are in common use for data communications and have enjoyed great success. Recently, there is a growing interest in using a single network to support many applications in addition to traditional data traffic. These additional applications introduce new requirements in terms of volume of traffic and real-time delivery of data which are not met by existing networks. To satisfy these requirements, a high-bandwidth tranmission medium, such as fiber optics, and a distributed channel access scheme for the efficient sharing of the bandwidth among the various applications are needed. As far as the throughput-delay requirements of the various application are concerned, a network structure along with a distributed channel access are proposed which incorporate appropriate scheduling policies for the transmission of outstanding messages on the network. A dynamic scheduling policy was devised which outperforms all existing policies in terms of minimizing the expected cost per message. A broadcast mechanism was devised for the efficient dissemination of all relevant information. Fiber optic technology is considered for the high-bandwidth transmisison medium.

Channel access schemes and fiber optic configurations for integrated-services local area networks. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Nassehi, M. Mehdi

1987-01-01

Local Area Networks are in common use for data communications and have enjoyed great success. Recently, there is a growing interest in using a single network to support many applications in addition to traditional data traffic. These additional applications introduce new requirements in terms of volume of traffic and real-time delivery of data which are not met by existing networks. To satisfy these requirements, a high-bandwidth tranmission medium, such as fiber optics, and a distributed channel access scheme for the efficient sharing of the bandwidth among the various applications are needed. As far as the throughput-delay requirements of the various application are concerned, a network structure along with a distributed channel access are proposed which incorporate appropriate scheduling policies for the transmission of outstanding messages on the network. A dynamic scheduling policy was devised which outperforms all existing policies in terms of minimizing the expected cost per message. A broadcast mechanism was devised for the efficient dissemination of all relevant information. Fiber optic technology is considered for the high-bandwidth transmisison medium.

What Does It Take to Change an Editor's Mind? Identifying Minimally Important Difference Thresholds for Peer Reviewer Rating Scores of Scientific Articles.

PubMed

Callaham, Michael; John, Leslie K

2018-01-05

We define a minimally important difference for the Likert-type scores frequently used in scientific peer review (similar to existing minimally important differences for scores in clinical medicine). The magnitude of score change required to change editorial decisions has not been studied, to our knowledge. Experienced editors at a journal in the top 6% by impact factor were asked how large a change of rating in "overall desirability for publication" was required to trigger a change in their initial decision on an article. Minimally important differences were assessed twice for each editor: once assessing the rating change required to shift the editor away from an initial decision to accept, and the other assessing the magnitude required to shift away from an initial rejection decision. Forty-one editors completed the survey (89% response rate). In the acceptance frame, the median minimally important difference was 0.4 points on a scale of 1 to 5. Editors required a greater rating change to shift from an initial rejection decision; in the rejection frame, the median minimally important difference was 1.2 points. Within each frame, there was considerable heterogeneity: in the acceptance frame, 38% of editors did not change their decision within the maximum available range; in the rejection frame, 51% did not. To our knowledge, this is the first study to determine the minimally important difference for Likert-type ratings of research article quality, or in fact any nonclinical scientific assessment variable. Our findings may be useful for future research assessing whether changes to the peer review process produce clinically meaningful differences in editorial decisionmaking. Copyright © 2017 American College of Emergency Physicians. Published by Elsevier Inc. All rights reserved.

A Modular, Reusable Latch and Decking System for Securing Payloads During Launch and Planetary Surface Transport

NASA Technical Reports Server (NTRS)

Doggett, William R.; Dorsey, John T.; Jones, Thomas C.; King, Bruce D.; Mikulas, Martin M.

2011-01-01

Efficient handling of payloads destined for a planetary surface, such as the moon or mars, requires robust systems to secure the payloads during transport on the ground, in space and on the planetary surface. In addition, mechanisms to release the payloads need to be reliable to ensure successful transfer from one vehicle to another. An efficient payload handling strategy must also consider the devices available to support payload handling. Cranes used for overhead lifting are common to all phases of payload handling on Earth. Similarly, both recent and past studies have demonstrated that devices with comparable functionality will be needed to support lunar outpost operations. A first generation test-bed of a new high performance device that provides the capabilities of both a crane and a robotic manipulator, the Lunar Surface Manipulation System (LSMS), has been designed, built and field tested and is available for use in evaluating a system to secure payloads to transportation vehicles. A payload handling approach must address all phases of payload management including: ground transportation, launch, planetary transfer and installation in the final system. In addition, storage may be required during any phase of operations. Each of these phases requires the payload to be lifted and secured to a vehicle, transported, released and lifted in preparation for the next transportation or storage phase. A critical component of a successful payload handling approach is a latch and associated carrier system. The latch and carrier system should minimize requirements on the: payload, carrier support structure and payload handling devices as well as be able to accommodate a wide range of payload sizes. In addition, the latch should; be small and lightweight, support a method to apply preload, be reusable, integrate into a minimal set of hard-points and have manual interfaces to actuate the latch should a problem occur. A latching system which meets these requirements has been designed and fabricated and will be described in detail. This latching system works in conjunction with a payload handling device such as the LSMS, and the LSMS has been used to test first generation latch and carrier hardware. All tests have been successful during the first phase of operational evaluations. Plans for future tests of first generation latch and carrier hardware with the LSMS are also described.

A Modular, Reusable Latch and Decking System for Securing Payloads During Launch and Planetary Surface Transport

NASA Technical Reports Server (NTRS)

Doggett, William R.; Dorsey, John T.; Jones, Thomas C.; King, Bruce D.; Mikulas, Martin M.

2010-01-01

Efficient handling of payloads destined for a planetary surface, such as the moon or Mars, requires robust systems to secure the payloads during transport on the ground, in-space and on the planetary surface. In addition, mechanisms to release the payloads need to be reliable to ensure successful transfer from one vehicle to another. An efficient payload handling strategy must also consider the devices available to support payload handling. Cranes used for overhead lifting are common to all phases of payload handling on Earth. Similarly, both recent and past studies have demonstrated that devices with comparable functionality will be needed to support lunar outpost operations. A first generation test-bed of a new high performance device that provides the capabilities of both a crane and a robotic manipulator, the Lunar Surface Manipulation System (LSMS), has been designed, built and field tested and is available for use in evaluating a system to secure payloads to transportation vehicles. National Institute of Aerospace, Hampton Va 23662 A payload handling approach must address all phases of payload management including: ground transportation, launch, planetary transfer and installation in the final system. In addition, storage may be required during any phase of operations. Each of these phases requires the payload to be lifted and secured to a vehicle, transported, released and lifted in preparation for the next transportation or storage phase. A critical component of a successful payload handling approach is a latch and associated carrier system. The latch and carrier system should minimize requirements on the: payload, carrier support structure and payload handling devices as well as be able to accommodate a wide range of payload sizes. In addition, the latch should; be small and lightweight, support a method to apply preload, be reusable, integrate into a minimal set of hard-points and have manual interfaces to actuate the latch should a problem occur. A latching system which meets these requirements has been designed and fabricated and will be described in detail. This latching system works in conjunction with a payload handling device such as the LSMS, and the LSMS has been used to test first generation latch and carrier hardware. All tests have been successful during the first phase of operational evaluations. Plans for future tests of first generation latch and carrier hardware with the LSMS are also described.

Life Cycle Environmental Impacts of Disinfection Technologies Used in Small Drinking Water Systems.

PubMed

Jones, Christopher H; Shilling, Elizabeth G; Linden, Karl G; Cook, Sherri M

2018-03-06

Small drinking water systems serve a fifth of the U.S. population and rely heavily on disinfection. While chlorine disinfection is common, there is interest in minimizing chemical addition, especially due to carcinogenic disinfection byproducts and chlorine-resistant pathogens, by using ultraviolet technologies; however, the relative, broader environmental impacts of these technologies are not well established, especially in the context of small (<10 000 people) water systems. The objective of this study was to identify environmental trade-offs between chlorine and ultraviolet disinfection via comparative life cycle assessment. The functional unit was the production of 1 m 3 of drinking water to U.S. Treatment included cartridge filtration followed by either chlorine disinfection or ultraviolet disinfection with chlorine residual addition. Environmental performance was evaluated for various chlorine contact zone materials (plastic, concrete, steel), ultraviolet validation factors (1.2 to 4.4), and electricity sources (renewable; U.S. average, high, and low impact grids). Performance was also evaluated when filtration and chlorine residual were not required. From a life cycle assessment perspective, replacing chlorine with UV was preferred only in a limited number of cases (i.e., high pumping pressure but filtration is not required). In all others, chlorine was environmentally preferred, although some contact zone materials and energy sources had an impact on the comparison. Utilities can use these data to inform their disinfection technology selection and operation to minimize environmental and human health impacts.

5 CFR 582.203 - Information minimally required to accompany legal process.

Code of Federal Regulations, 2012 CFR

2012-01-01

... accompany legal process. 582.203 Section 582.203 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS COMMERCIAL GARNISHMENT OF FEDERAL EMPLOYEES' PAY Service of Legal Process § 582.203 Information minimally required to accompany legal process. (a) Sufficient identifying...

5 CFR 582.203 - Information minimally required to accompany legal process.

Code of Federal Regulations, 2010 CFR

2010-01-01

... accompany legal process. 582.203 Section 582.203 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS COMMERCIAL GARNISHMENT OF FEDERAL EMPLOYEES' PAY Service of Legal Process § 582.203 Information minimally required to accompany legal process. (a) Sufficient identifying...

5 CFR 582.203 - Information minimally required to accompany legal process.

Code of Federal Regulations, 2011 CFR

2011-01-01

... accompany legal process. 582.203 Section 582.203 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS COMMERCIAL GARNISHMENT OF FEDERAL EMPLOYEES' PAY Service of Legal Process § 582.203 Information minimally required to accompany legal process. (a) Sufficient identifying...

5 CFR 582.203 - Information minimally required to accompany legal process.

Code of Federal Regulations, 2014 CFR

2014-01-01

... accompany legal process. 582.203 Section 582.203 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS COMMERCIAL GARNISHMENT OF FEDERAL EMPLOYEES' PAY Service of Legal Process § 582.203 Information minimally required to accompany legal process. (a) Sufficient identifying...

5 CFR 582.203 - Information minimally required to accompany legal process.

Code of Federal Regulations, 2013 CFR

2013-01-01

... accompany legal process. 582.203 Section 582.203 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS COMMERCIAL GARNISHMENT OF FEDERAL EMPLOYEES' PAY Service of Legal Process § 582.203 Information minimally required to accompany legal process. (a) Sufficient identifying...

Determining the Minimal Required Radioactivity of 18F-FDG for Reliable Semiquantification in PET/CT Imaging: A Phantom Study.

PubMed

Chen, Ming-Kai; Menard, David H; Cheng, David W

2016-03-01

In pursuit of as-low-as-reasonably-achievable (ALARA) doses, this study investigated the minimal required radioactivity and corresponding imaging time for reliable semiquantification in PET/CT imaging. Using a phantom containing spheres of various diameters (3.4, 2.1, 1.5, 1.2, and 1.0 cm) filled with a fixed (18)F-FDG concentration of 165 kBq/mL and a background concentration of 23.3 kBq/mL, we performed PET/CT at multiple time points over 20 h of radioactive decay. The images were acquired for 10 min at a single bed position for each of 10 half-lives of decay using 3-dimensional list mode and were reconstructed into 1-, 2-, 3-, 4-, 5-, and 10-min acquisitions per bed position using an ordered-subsets expectation maximum algorithm with 24 subsets and 2 iterations and a gaussian 2-mm filter. SUVmax and SUVavg were measured for each sphere. The minimal required activity (±10%) for precise SUVmax semiquantification in the spheres was 1.8 kBq/mL for an acquisition of 10 min, 3.7 kBq/mL for 3-5 min, 7.9 kBq/mL for 2 min, and 17.4 kBq/mL for 1 min. The minimal required activity concentration-acquisition time product per bed position was 10-15 kBq/mL⋅min for reproducible SUV measurements within the spheres without overestimation. Using the total radioactivity and counting rate from the entire phantom, we found that the minimal required total activity-time product was 17 MBq⋅min and the minimal required counting rate-time product was 100 kcps⋅min. Our phantom study determined a threshold for minimal radioactivity and acquisition time for precise semiquantification in (18)F-FDG PET imaging that can serve as a guide in pursuit of achieving ALARA doses. © 2016 by the Society of Nuclear Medicine and Molecular Imaging, Inc.

Exploration of Objective Functions for Optimal Placement of Weather Stations

NASA Astrophysics Data System (ADS)

Snyder, A.; Dietterich, T.; Selker, J. S.

2016-12-01

Many regions of Earth lack ground-based sensing of weather variables. For example, most countries in Sub-Saharan Africa do not have reliable weather station networks. This absence of sensor data has many consequences ranging from public safety (poor prediction and detection of severe weather events), to agriculture (lack of crop insurance), to science (reduced quality of world-wide weather forecasts, climate change measurement, etc.). The Trans-African Hydro-Meteorological Observatory (TAHMO.org) project seeks to address these problems by deploying and operating a large network of weather stations throughout Sub-Saharan Africa. To design the TAHMO network, we must determine where to locate each weather station. We can formulate this as the following optimization problem: Determine a set of N sites that jointly optimize the value of an objective function. The purpose of this poster is to propose and assess several objective functions. In addition to standard objectives (e.g., minimizing the summed squared error of interpolated values over the entire region), we consider objectives that minimize the maximum error over the region and objectives that optimize the detection of extreme events. An additional issue is that each station measures more than 10 variables—how should we balance the accuracy of our interpolated maps for each variable? Weather sensors inevitably drift out of calibration or fail altogether. How can we incorporate robustness to failed sensors into our network design? Another important requirement is that the network should make it possible to detect failed sensors by comparing their readings with those of other stations. How can this requirement be met? Finally, we provide an initial assessment of the computational cost of optimizing these various objective functions. We invite everyone to join the discussion at our poster by proposing additional objectives, identifying additional issues to consider, and expanding our bibliography of relevant papers. A prize (derived from grapes grown in Oregon) will be awarded for the most insightful contribution to the discussion!

Persistence of an Oncogenic Papillomavirus Genome Requires cis Elements from the Viral Transcriptional Enhancer

PubMed Central

Van Doorslaer, Koenraad; Chen, Dan; Chapman, Sandra; Khan, Jameela

2017-01-01

ABSTRACT Human papillomavirus (HPV) genomes are replicated and maintained as extrachromosomal plasmids during persistent infection. The viral E2 proteins are thought to promote stable maintenance replication by tethering the viral DNA to host chromatin. However, this has been very difficult to prove genetically, as the E2 protein is involved in transcriptional regulation and initiation of replication, as well as its assumed role in genome maintenance. This makes mutational analysis of viral trans factors and cis elements in the background of the viral genome problematic and difficult to interpret. To circumvent this problem, we have developed a complementation assay in which the complete wild-type HPV18 genome is transfected into primary human keratinocytes along with subgenomic or mutated replicons that contain the minimal replication origin. The wild-type genome provides the E1 and E2 proteins in trans, allowing us to determine additional cis elements that are required for long-term replication and partitioning of the replicon. We found that, in addition to the core replication origin (and the three E2 binding sites located therein), additional sequences from the transcriptional enhancer portion of the URR (upstream regulatory region) are required in cis for long-term genome replication. PMID:29162712

The study about forming high-precision optical lens minimalized sinuous error structures for designed surface

NASA Astrophysics Data System (ADS)

Katahira, Yu; Fukuta, Masahiko; Katsuki, Masahide; Momochi, Takeshi; Yamamoto, Yoshihiro

2016-09-01

Recently, it has been required to improve qualities of aspherical lenses mounted on camera units. Optical lenses in highvolume production generally are applied with molding process using cemented carbide or Ni-P coated steel, which can be selected from lens material such as glass and plastic. Additionally it can be obtained high quality of the cut or ground surface on mold due to developments of different mold product technologies. As results, it can be less than 100nmPV as form-error and 1nmRa as surface roughness in molds. Furthermore it comes to need higher quality, not only formerror( PV) and surface roughness(Ra) but also other surface characteristics. For instance, it can be caused distorted shapes at imaging by middle spatial frequency undulations on the lens surface. In this study, we made focus on several types of sinuous structures, which can be classified into form errors for designed surface and deteriorate optical system performances. And it was obtained mold product processes minimalizing undulations on the surface. In the report, it was mentioned about the analyzing process by using PSD so as to evaluate micro undulations on the machined surface quantitatively. In addition, it was mentioned that the grinding process with circumferential velocity control was effective for large aperture lenses fabrication and could minimalize undulations appeared on outer area of the machined surface, and mentioned about the optical glass lens molding process by using the high precision press machine.

Lunar Surface-to-Surface Power Transfer

NASA Technical Reports Server (NTRS)

Kerslake, Thomas W.

2007-01-01

A human lunar outpost, under NASA study for construction in the 2020's, has potential requirements to transfer electric power up to 50-kW across the lunar surface from 0.1 to 10-km distances. This power would be used to operate surface payloads located remotely from the outpost and/or outpost primary power grid. This paper describes concept designs for state-of-the-art technology power transfer subsystems including AC or DC power via cables, beamed radio frequency power and beamed laser power. Power transfer subsystem mass and performance are calculated and compared for each option. A simplified qualitative assessment of option operations, hazards, costs and technology needs is also described. Based on these concept designs and performance analyses, a DC power cabling subsystem is recommended to minimize subsystem mass and to minimize mission and programmatic costs and risks. Avenues for additional power transfer subsystem studies are recommended.

Advances in Green Organic Sonochemistry.

PubMed

Draye, Micheline; Kardos, Nathalie

2016-10-01

Over the past 15 years, sustainable chemistry has emerged as a new paradigm in the development of chemistry. In the field of organic synthesis, green chemistry rhymes with relevant choice of starting materials, atom economy, methodologies that minimize the number of chemical steps, appropriate use of benign solvents and reagents, efficient strategies for product isolation and purification and energy minimization. In that context, unconventional methods, and especially ultrasound, can be a fine addition towards achieving these green requirements. Undoubtedly, sonochemistry is considered as being one of the most promising green chemical methods (Cravotto et al. Catal Commun 63: 2-9, 2015). This review is devoted to the most striking results obtained in green organic sonochemistry between 2006 and 2016. Furthermore, among catalytic transformations, oxidation reactions are the most polluting reactions in the chemical industry; thus, we have focused a part of our review on the very promising catalytic activity of ultrasound for oxidative purposes.

Obtaining Soluble Folded Proteins from Inclusion Bodies Using Sarkosyl, Triton X-100, and CHAPS: Application to LB and M9 Minimal Media.

PubMed

Massiah, Michael A; Wright, Katharine M; Du, Haijuan

2016-04-01

This unit describes a straightforward and efficient method of using sarkosyl to solubilize and recover difficult recombinant proteins, such as GST- and His6 -tagged fusion proteins, that are overexpressed in E. coli. This protocol is especially useful for rescuing recombinant proteins overexpressed in M9 minimal medium. Sarkosyl added to lysis buffers helps with both protein solubility and cell lysis. Higher percentage sarkosyl (up to 10%) can extract >95% of soluble protein from inclusion bodies. In the case of sarkosyl-solubilized GST-fusion proteins, batch-mode affinity purification requires addition of a specific ratio of Triton X-100 and CHAPS, while sarkosyl-solubilized His6 -tagged fusion proteins can be directly purified on Ni(2+) resin columns. Proteins purified by this method could be widely used in biological assays, structure analysis and mass spectrum assay. Copyright © 2016 John Wiley & Sons, Inc.

The applications of deep neural networks to sdBV classification

NASA Astrophysics Data System (ADS)

Boudreaux, Thomas M.

2017-12-01

With several new large-scale surveys on the horizon, including LSST, TESS, ZTF, and Evryscope, faster and more accurate analysis methods will be required to adequately process the enormous amount of data produced. Deep learning, used in industry for years now, allows for advanced feature detection in minimally prepared datasets at very high speeds; however, despite the advantages of this method, its application to astrophysics has not yet been extensively explored. This dearth may be due to a lack of training data available to researchers. Here we generate synthetic data loosely mimicking the properties of acoustic mode pulsating stars and we show that two separate paradigms of deep learning - the Artificial Neural Network And the Convolutional Neural Network - can both be used to classify this synthetic data effectively. And that additionally this classification can be performed at relatively high levels of accuracy with minimal time spent adjusting network hyperparameters.

5 CFR 581.203 - Information minimally required to accompany legal process.

Code of Federal Regulations, 2014 CFR

2014-01-01

... accompany legal process. 581.203 Section 581.203 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT... Process § 581.203 Information minimally required to accompany legal process. (a) Sufficient identifying information must accompany the legal process in order to enable processing by the governmental entity named...

5 CFR 581.203 - Information minimally required to accompany legal process.

Code of Federal Regulations, 2011 CFR

2011-01-01

... accompany legal process. 581.203 Section 581.203 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT... Process § 581.203 Information minimally required to accompany legal process. (a) Sufficient identifying information must accompany the legal process in order to enable processing by the governmental entity named...

5 CFR 581.203 - Information minimally required to accompany legal process.

Code of Federal Regulations, 2013 CFR

2013-01-01

... accompany legal process. 581.203 Section 581.203 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT... Process § 581.203 Information minimally required to accompany legal process. (a) Sufficient identifying information must accompany the legal process in order to enable processing by the governmental entity named...

5 CFR 581.203 - Information minimally required to accompany legal process.

Code of Federal Regulations, 2012 CFR

2012-01-01

... accompany legal process. 581.203 Section 581.203 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT... Process § 581.203 Information minimally required to accompany legal process. (a) Sufficient identifying information must accompany the legal process in order to enable processing by the governmental entity named...

5 CFR 581.203 - Information minimally required to accompany legal process.

Code of Federal Regulations, 2010 CFR

2010-01-01

... accompany legal process. 581.203 Section 581.203 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT... Process § 581.203 Information minimally required to accompany legal process. (a) Sufficient identifying information must accompany the legal process in order to enable processing by the governmental entity named...

Non-Axisymmetric Inflatable Pressure Structure (NAIPS) Concept that Enables Mass Efficient Packageable Pressure Vessels with Sealable Openings

NASA Technical Reports Server (NTRS)

Doggett, William R.; Jones, Thomas C.; Kenner, Winfred S.; Moore, David F.; Watson, Judith J.; Warren, Jerry E.; Makino, Alberto; Yount, Bryan; Selig, Molly; Shariff, Khadijah;

Spacecraft Conceptual Design Compared to the Apollo Lunar Lander

NASA Technical Reports Server (NTRS)

Young, C.; Bowie, J.; Rust, R.; Lenius, J.; Anderson, M.; Connolly, J.

2011-01-01

Future human exploration of the Moon will require an optimized spacecraft design with each sub-system achieving the required minimum capability and maintaining high reliability. The objective of this study was to trade capability with reliability and minimize mass for the lunar lander spacecraft. The NASA parametric concept for a 3-person vehicle to the lunar surface with a 30% mass margin totaled was considerably heavier than the Apollo 15 Lunar Module "as flown" mass of 16.4 metric tons. The additional mass was attributed to mission requirements and system design choices that were made to meet the realities of modern spaceflight. The parametric tool used to size the current concept, Envision, accounts for primary and secondary mass requirements. For example, adding an astronaut increases the mass requirements for suits, water, food, oxygen, as well as, the increase in volume. The environmental control sub-systems becomes heavier with the increased requirements and more structure was needed to support the additional mass. There was also an increase in propellant usage. For comparison, an "Apollo-like" vehicle was created by removing these additional requirements. Utilizing the Envision parametric mass calculation tool and a quantitative reliability estimation tool designed by Valador Inc., it was determined that with today?s current technology a Lunar Module (LM) with Apollo capability could be built with less mass and similar reliability. The reliability of this new lander was compared to Apollo Lunar Module utilizing the same methodology, adjusting for mission timeline changes as well as component differences. Interestingly, the parametric concept's overall estimated risk for loss of mission (LOM) and loss of crew (LOC) did not significantly improve when compared to Apollo.

Environmental assessment of the 40 kilowatt fuel cell system field test operation

NASA Technical Reports Server (NTRS)

Bollenbacher, G.

1982-01-01

This environmental assessment examines the potential environmental consequences, both adverse and beneficial, of the 40 kW fuel cell system system field test operation. The assessment is of necessity generic in nature since actual test sites were not selected. This assessment provides the basis for determining the need for an environmental impact statement. In addition, this assessment provides siting criteria to avoid or minimize negative environmental impacts and standards for determining candidate test sites, if any, for which site specific assessments may be required.

Requirements for maintaining cryogenic propellants during planetary surface stays

NASA Technical Reports Server (NTRS)

Riccio, Joseph R.; Schoenberg, Richard J.

1991-01-01

Potential impacts on the planetary surface system infrastructure resulting from the use of liquid hydrogen and oxygen propellants for a stage and half lander are discussed. Particular attention is given to techniques which can be incorporated into the surface infrastructure and/or the vehicle to minimize the impact resulting from the use of these cryogens. Methods offered for reducing cryogenic propellant boiloff include modification of the lander to accommodate boiloff, incorporation of passive thermal control devices to the lander, addition of active propellant management, and use of alternative propellants.

Powder Metallurgy Reconditioning of Food and Processing Equipment Components

NASA Astrophysics Data System (ADS)

Nafikov, M. Z.; Aipov, R. S.; Konnov, A. Yu.

2017-12-01

A powder metallurgy method is developed to recondition the worn surfaces of food and processing equipment components. A combined additive is composed to minimize the powder losses in sintering. A technique is constructed to determine the powder consumption as a function of the required metallic coating thickness. A rapid method is developed to determine the porosity of the coating. The proposed technology is used to fabricate a wear-resistant defectless metallic coating with favorable residual stresses, and the adhesive strength of this coating is equal to the strength of the base metal.

Wise use of water in smart cities - possibilities and limitations

NASA Astrophysics Data System (ADS)

Bąk, Joanna

2018-02-01

The need to save water is due, inter alia, to the paradigm of sustainable development. There are many ways to minimize the consumption of high quality water supplied by the water supply network. These include the simplest way and those complex, requiring additional installation. The lack of water is a big problem, but not only water deficit are dangerous. There is a possibility of secondary water pollution in the water supply network due to changes in network parameters. Changes in these parameters may occur due to reduced demand for water by residents and, as a result, reduced water flow - at the same pipe diameter. The article includes a review with comparative analysis of various classification systems for the tap fittings and other sanitary equipment, such as the Water Efficiency Label (WELL) in Europe or the Water Efficiency Labelling and Standards (WELS) in Australia. Several types of perlators and flow regulators were compared in the research section. This equipment was tested in the household. The possibilities of minimizing water consumption by using them was collated. In addition, the work also analyses the evolution of water consumption in Poland in recent years and their possible relationship with the threats quality of drinking water supplied to consumers.

Semiconductor Seeded Nanorods with Graded Composition Exhibiting High Quantum-Yield, High Polarization, and Minimal Blinking.

PubMed

Hadar, Ido; Philbin, John P; Panfil, Yossef E; Neyshtadt, Shany; Lieberman, Itai; Eshet, Hagai; Lazar, Sorin; Rabani, Eran; Banin, Uri

2017-04-12

Seeded semiconductor nanorods represent a unique family of quantum confined materials that manifest characteristics of mixed dimensionality. They show polarized emission with high quantum yield and fluorescence switching under an electric field, features that are desirable for use in display technologies and other optical applications. So far, their robust synthesis has been limited mainly to CdSe/CdS heterostructures, thereby constraining the spectral tunability to the red region of the visible spectrum. Herein we present a novel synthesis of CdSe/Cd 1-x Zn x S seeded nanorods with a radially graded composition that show bright and highly polarized green emission with minimal intermittency, as confirmed by ensemble and single nanorods optical measurements. Atomistic pseudopotential simulations elucidate the importance of the Zn atoms within the nanorod structure, in particular the effect of the graded composition. Thus, the controlled addition of Zn influences and improves the nanorods' optoelectronic performance by providing an additional handle to manipulate the degree confinement beyond the common size control approach. These nanorods may be utilized in applications that require the generation of a full, rich spectrum such as energy-efficient displays and lighting.

Work intensity in sacroiliac joint fusion and lumbar microdiscectomy

PubMed Central

Frank, Clay; Kondrashov, Dimitriy; Meyer, S Craig; Dix, Gary; Lorio, Morgan; Kovalsky, Don; Cher, Daniel

2016-01-01

Background The evidence base supporting minimally invasive sacroiliac (SI) joint fusion (SIJF) surgery is increasing. The work relative value units (RVUs) associated with minimally invasive SIJF are seemingly low. To date, only one published study describes the relative work intensity associated with minimally invasive SIJF. No study has compared work intensity vs other commonly performed spine surgery procedures. Methods Charts of 192 patients at five sites who underwent either minimally invasive SIJF (American Medical Association [AMA] CPT® code 27279) or lumbar microdiscectomy (AMA CPT® code 63030) were reviewed. Abstracted were preoperative times associated with diagnosis and patient care, intraoperative parameters including operating room (OR) in/out times and procedure start/stop times, and postoperative care requirements. Additionally, using a visual analog scale, surgeons estimated the intensity of intraoperative care, including mental, temporal, and physical demands and effort and frustration. Work was defined as operative time multiplied by task intensity. Results Patients who underwent minimally invasive SIJF were more likely female. Mean procedure times were lower in SIJF by about 27.8 minutes (P<0.0001) and mean total OR times were lower by 27.9 minutes (P<0.0001), but there was substantial overlap across procedures. Mean preservice and post-service total labor times were longer in minimally invasive SIJF (preservice times longer by 63.5 minutes [P<0.0001] and post-service labor times longer by 20.2 minutes [P<0.0001]). The number of postoperative visits was higher in minimally invasive SIJF. Mean total service time (preoperative + OR time + postoperative) was higher in the minimally invasive SIJF group (261.5 vs 211.9 minutes, P<0.0001). Intraoperative intensity levels were higher for mental, physical, effort, and frustration domains (P<0.0001 each). After taking into account intensity, intraoperative workloads showed substantial overlap. Conclusion Compared to a commonly performed lumbar spine surgical procedure, lumbar microdiscectomy, that currently has a higher work RVU, preoperative, intraoperative, and postoperative workload for minimally invasive SIJF is higher. The work RVU for minimally invasive SIJF should be adjusted upward as the relative amount of work is comparable. PMID:27555790

Comparisons of Food and Drug Administration and European Medicines Agency risk management implementation for recent pharmaceutical approvals: report of the International Society for Pharmacoeconomics and outcomes research risk benefit management working group.

PubMed

Lis, Yvonne; Roberts, Melissa H; Kamble, Shital; J Guo, Jeff; Raisch, Dennis W

2012-12-01

1) To compare the Food and Drug Administration's (FDA's) Risk Evaluation and Mitigation Strategies (REMS) and European Medicines Agency's (EMA's) Risk Management Plan (RMP) guidances and 2) to compare REMS and RMPs for specific chemical entities and biological products. FDA, EMA, and pharmaceutical company Web sites were consulted for details pertaining to REMS and RMPs. REMS requirements include medication guides, communication plans, elements to ensure safe use, implementation systems, and specified assessment intervals. RMP requirements are increased pharmacovigilance and risk minimization activities. We compared these requirements for drugs requiring both REMS and RMPs. We identified 95 drugs on FDA's REMS list as of March 2010. Of these, there were 29 drugs (11 biologics and 18 new chemical entities) with EMA RMPs. REMS and RMPs are similar in objectives, with comparable toolkits. Both allow flexibility in product-specific actions, recognizing adverse effects of potential concern. Of the 29 drugs reviewed, REMS requirements not included in RMPs were patient medication guides (100% of the drugs), provider communication plans (38%), and routine monitoring of REMS (66%). RMP requirements not included in REMS were specific adverse event reporting (45% of the drugs), prospective registry studies (34%), prospective epidemiology studies (24%), additional trial data (28%), and Summary of Product Characteristics contraindications (76%). Both REMS and RMPs provide positive guidance for identification, monitoring, and minimization of risk to patient safety. Currently, neither agency provides specific guidance on how risk should be related to benefit either qualitatively or quantitatively. Copyright © 2012 International Society for Pharmacoeconomics and Outcomes Research (ISPOR). Published by Elsevier Inc. All rights reserved.

Efficiency of unconstrained minimization techniques in nonlinear analysis

NASA Technical Reports Server (NTRS)

Kamat, M. P.; Knight, N. F., Jr.

1978-01-01

Unconstrained minimization algorithms have been critically evaluated for their effectiveness in solving structural problems involving geometric and material nonlinearities. The algorithms have been categorized as being zeroth, first, or second order depending upon the highest derivative of the function required by the algorithm. The sensitivity of these algorithms to the accuracy of derivatives clearly suggests using analytically derived gradients instead of finite difference approximations. The use of analytic gradients results in better control of the number of minimizations required for convergence to the exact solution.

Software Development and Test Methodology for a Distributed Ground System

NASA Technical Reports Server (NTRS)

Ritter, George; Guillebeau, Pat; McNair, Ann R. (Technical Monitor)

2002-01-01

The Marshall Space Flight Center's (MSFC) Payload Operations Center (POC) ground system has evolved over a period of about 10 years. During this time the software processes have migrated from more traditional to more contemporary development processes in an effort to minimize unnecessary overhead while maximizing process benefits. The Software processes that have evolved still emphasize requirements capture, software configuration management, design documenting, and making sure the products that have been developed are accountable to initial requirements. This paper will give an overview of how the Software Processes have evolved, highlighting the positives as well as the negatives. In addition, we will mention the COTS tools that have been integrated into the processes and how the COTS have provided value to the project.

Real-Time Aerodynamic Flow and Data Visualization in an Interactive Virtual Environment

NASA Technical Reports Server (NTRS)

Schwartz, Richard J.; Fleming, Gary A.

2005-01-01

Significant advances have been made to non-intrusive flow field diagnostics in the past decade. Camera based techniques are now capable of determining physical qualities such as surface deformation, surface pressure and temperature, flow velocities, and molecular species concentration. In each case, extracting the pertinent information from the large volume of acquired data requires powerful and efficient data visualization tools. The additional requirement for real time visualization is fueled by an increased emphasis on minimizing test time in expensive facilities. This paper will address a capability titled LiveView3D, which is the first step in the development phase of an in depth, real time data visualization and analysis tool for use in aerospace testing facilities.

Modular optical detector system

DOEpatents

Horn, Brent A [Livermore, CA; Renzi, Ronald F [Tracy, CA

2006-02-14

A modular optical detector system. The detector system is designed to detect the presence of molecules or molecular species by inducing fluorescence with exciting radiation and detecting the emitted fluorescence. Because the system is capable of accurately detecting and measuring picomolar concentrations it is ideally suited for use with microchemical analysis systems generally and capillary chromatographic systems in particular. By employing a modular design, the detector system provides both the ability to replace various elements of the detector system without requiring extensive realignment or recalibration of the components as well as minimal user interaction with the system. In addition, the modular concept provides for the use and addition of a wide variety of components, including optical elements (lenses and filters), light sources, and detection means, to fit particular needs.

L-Glycine Alleviates Furfural-Induced Growth Inhibition during Isobutanol Production in Escherichia coli.

PubMed

Song, Hun-Suk; Jeon, Jong-Min; Choi, Yong Keun; Kim, Jun-Young; Kim, Wooseong; Yoon, Jeong-Jun; Park, Kyungmoon; Ahn, Jungoh; Lee, Hongweon; Yang, Yung-Hun

2017-12-28

Lignocellulose is now a promising raw material for biofuel production. However, the lignin complex and crystalline cellulose require pretreatment steps for breakdown of the crystalline structure of cellulose for the generation of fermentable sugars. Moreover, several fermentation inhibitors are generated with sugar compounds, majorly furfural. The mitigation of these inhibitors is required for the further fermentation steps to proceed. Amino acids were investigated on furfural-induced growth inhibition in E. coli producing isobutanol. Glycine and serine were the most effective compounds against furfural. In minimal media, glycine conferred tolerance against furfural. From the IC₅₀ value for inhibitors in the production media, only glycine could alleviate growth arrest for furfural, where 6 mM glycine addition led to a slight increase in growth rate and isobutanol production from 2.6 to 2.8 g/l under furfural stress. Overexpression of glycine pathway genes did not lead to alleviation. However, addition of glycine to engineered strains blocked the growth arrest and increased the isobutanol production about 2.3-fold.

Harnessing the Big Data Paradigm for ICME: Shifting from Materials Selection to Materials Enabled Design

NASA Astrophysics Data System (ADS)

Broderick, Scott R.; Santhanam, Ganesh Ram; Rajan, Krishna

2016-08-01

As the size of databases has significantly increased, whether through high throughput computation or through informatics-based modeling, the challenge of selecting the optimal material for specific design requirements has also arisen. Given the multiple, and often conflicting, design requirements, this selection process is not as trivial as sorting the database for a given property value. We suggest that the materials selection process should minimize selector bias, as well as take data uncertainty into account. For this reason, we discuss and apply decision theory for identifying chemical additions to Ni-base alloys. We demonstrate and compare results for both a computational array of chemistries and standard commercial superalloys. We demonstrate how we can use decision theory to select the best chemical additions for enhancing both property and processing, which would not otherwise be easily identifiable. This work is one of the first examples of introducing the mathematical framework of set theory and decision analysis into the domain of the materials selection process.

Wall jet analysis for circulation control aerodynamics. Part 1: Fundamental CFD and turbulence modeling concepts

NASA Technical Reports Server (NTRS)

Dash, S. M.; York, B. J.; Sinha, N.; Dvorak, F. A.

1987-01-01

An overview of parabolic and PNS (Parabolized Navier-Stokes) methodology developed to treat highly curved sub and supersonic wall jets is presented. The fundamental data base to which these models were applied is discussed in detail. The analysis of strong curvature effects was found to require a semi-elliptic extension of the parabolic modeling to account for turbulent contributions to the normal pressure variations, as well as an extension to the turbulence models utilized, to account for the highly enhanced mixing rates observed in situations with large convex curvature. A noniterative, pressure split procedure is shown to extend parabolic models to account for such normal pressure variations in an efficient manner, requiring minimal additional run time over a standard parabolic approach. A new PNS methodology is presented to solve this problem which extends parabolic methodology via the addition of a characteristic base wave solver. Applications of this approach to analyze the interaction of wave and turbulence processes in wall jets is presented.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burger, Brian T.; Imam, Saheed; Scarborough, Matthew J.

Rhodobacter sphaeroides is one of the best-studied alphaproteobacteria from biochemical, genetic, and genomic perspectives. To gain a better systems-level understanding of this organism, we generated a large transposon mutant library and used transposon sequencing (Tn-seq) to identify genes that are essential under several growth conditions. Using newly developed Tn-seq analysis software (TSAS), we identified 493 genes as essential for aerobic growth on a rich medium. We then used the mutant library to identify conditionally essential genes under two laboratory growth conditions, identifying 85 additional genes required for aerobic growth in a minimal medium and 31 additional genes required for photosyntheticmore » growth. In all instances, our analyses confirmed essentiality for many known genes and identified genes not previously considered to be essential. We used the resulting Tn-seq data to refine and improve a genome-scale metabolic network model (GEM) for R. sphaeroides. Together, we demonstrate how genetic, genomic, and computational approaches can be combined to obtain a systems-level understanding of the genetic framework underlying metabolic diversity in bacterial species.« less

36 CFR 228.8 - Requirements for environmental protection.

Code of Federal Regulations, 2012 CFR

2012-07-01

... shall be conducted so as, where feasible, to minimize adverse environmental impacts on National Forest..., shall either be removed from National Forest lands or disposed of or treated so as to minimize, so far... 36 Parks, Forests, and Public Property 2 2012-07-01 2012-07-01 false Requirements for...

36 CFR 228.8 - Requirements for environmental protection.

Code of Federal Regulations, 2014 CFR

2014-07-01

... shall be conducted so as, where feasible, to minimize adverse environmental impacts on National Forest..., shall either be removed from National Forest lands or disposed of or treated so as to minimize, so far... 36 Parks, Forests, and Public Property 2 2014-07-01 2014-07-01 false Requirements for...

36 CFR 228.8 - Requirements for environmental protection.

Code of Federal Regulations, 2013 CFR

2013-07-01

... shall be conducted so as, where feasible, to minimize adverse environmental impacts on National Forest..., shall either be removed from National Forest lands or disposed of or treated so as to minimize, so far... 36 Parks, Forests, and Public Property 2 2013-07-01 2013-07-01 false Requirements for...

40 CFR 63.6605 - What are my general requirements for complying with this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

... maintain any affected source, including associated air pollution control equipment and monitoring equipment, in a manner consistent with safety and good air pollution control practices for minimizing emissions. The general duty to minimize emissions does not require you to make any further efforts to reduce...

Responsible gambling: general principles and minimal requirements.

PubMed

Blaszczynski, Alex; Collins, Peter; Fong, Davis; Ladouceur, Robert; Nower, Lia; Shaffer, Howard J; Tavares, Hermano; Venisse, Jean-Luc

2011-12-01

Many international jurisdictions have introduced responsible gambling programs. These programs intend to minimize negative consequences of excessive gambling, but vary considerably in their aims, focus, and content. Many responsible gambling programs lack a conceptual framework and, in the absence of empirical data, their components are based only on general considerations and impressions. This paper outlines the consensus viewpoint of an international group of researchers suggesting fundamental responsible gambling principles, roles of key stakeholders, and minimal requirements that stakeholders can use to frame and inform responsible gambling programs across jurisdictions. Such a framework does not purport to offer value statements regarding the legal status of gambling or its expansion. Rather, it proposes gambling-related initiatives aimed at government, industry, and individuals to promote responsible gambling and consumer protection. This paper argues that there is a set of basic principles and minimal requirements that should form the basis for every responsible gambling program.

PLA realizations for VLSI state machines

NASA Technical Reports Server (NTRS)

Gopalakrishnan, S.; Whitaker, S.; Maki, G.; Liu, K.

1990-01-01

A major problem associated with state assignment procedures for VLSI controllers is obtaining an assignment that produces minimal or near minimal logic. The key item in Programmable Logic Array (PLA) area minimization is the number of unique product terms required by the design equations. This paper presents a state assignment algorithm for minimizing the number of product terms required to implement a finite state machine using a PLA. Partition algebra with predecessor state information is used to derive a near optimal state assignment. A maximum bound on the number of product terms required can be obtained by inspecting the predecessor state information. The state assignment algorithm presented is much simpler than existing procedures and leads to the same number of product terms or less. An area-efficient PLA structure implemented in a 1.0 micron CMOS process is presented along with a summary of the performance for a controller implemented using this design procedure.

Pectoral Fascial (PECS) I and II Blocks as Rescue Analgesia in a Patient Undergoing Minimally Invasive Cardiac Surgery.

PubMed

Yalamuri, Suraj; Klinger, Rebecca Y; Bullock, W Michael; Glower, Donald D; Bottiger, Brandi A; Gadsden, Jeffrey C

Patients undergoing minimally invasive cardiac surgery have the potential for significant pain from the thoracotomy site. We report the successful use of pectoral nerve block types I and II (Pecs I and II) as rescue analgesia in a patient undergoing minimally invasive mitral valve repair. In this case, a 78-year-old man, with no history of chronic pain, underwent mitral valve repair via right anterior thoracotomy for severe mitral regurgitation. After extubation, he complained of 10/10 pain at the incision site that was minimally responsive to intravenous opioids. He required supplemental oxygen because of poor pulmonary mechanics, with shallow breathing and splinting due to pain, and subsequent intensive care unit readmission. Ultrasound-guided Pecs I and II blocks were performed on the right side with 30 mL of 0.2% ropivacaine with 1:400,000 epinephrine. The blocks resulted in near-complete chest wall analgesia and improved pulmonary mechanics for approximately 24 hours. After the single-injection blocks regressed, a second set of blocks was performed with 266 mg of liposomal bupivacaine mixed with bupivacaine. This second set of blocks provided extended analgesia for an additional 48 hours. The patient was weaned rapidly from supplemental oxygen after the blocks because of improved analgesia. Pectoral nerve blocks have been described in the setting of breast surgery to provide chest wall analgesia. We report the first successful use of Pecs blocks to provide effective chest wall analgesia for a patient undergoing minimally invasive cardiac surgery with thoracotomy. We believe that these blocks may provide an important nonopioid option for the management of pain during recovery from minimally invasive cardiac surgery.

76 FR 30550 - Federal Management Regulation; Change in Consumer Price Index Minimal Value

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-26

... Minimal Value AGENCY: Office of Governmentwide Policy, GSA. ACTION: Final rule. SUMMARY: Pursuant to 5 U.S.C. 7342, at three-year intervals following January 1, 1981, the minimal value for foreign gifts must... required consultation has been completed and the minimal value has been increased to $350 or less as of...

Finding Minimal Addition Chains with a Particle Swarm Optimization Algorithm

NASA Astrophysics Data System (ADS)

León-Javier, Alejandro; Cruz-Cortés, Nareli; Moreno-Armendáriz, Marco A.; Orantes-Jiménez, Sandra

The addition chains with minimal length are the basic block to the optimal computation of finite field exponentiations. It has very important applications in the areas of error-correcting codes and cryptography. However, obtaining the shortest addition chains for a given exponent is a NP-hard problem. In this work we propose the adaptation of a Particle Swarm Optimization algorithm to deal with this problem. Our proposal is tested on several exponents whose addition chains are considered hard to find. We obtained very promising results.

Initial multicenter technical experience with the Apollo device for minimally invasive intracerebral hematoma evacuation.

PubMed

Spiotta, Alejandro M; Fiorella, David; Vargas, Jan; Khalessi, Alexander; Hoit, Dan; Arthur, Adam; Lena, Jonathan; Turk, Aquilla S; Chaudry, M Imran; Gutman, Frederick; Davis, Raphael; Chesler, David A; Turner, Raymond D

2015-06-01

No conventional surgical intervention has been shown to improve outcomes for patients with spontaneous intracerebral hemorrhage (ICH) compared with medical management. We report the initial multicenter experience with a novel technique for the minimally invasive evacuation of ICH using the Penumbra Apollo system (Penumbra Inc, Alameda, California). Institutional databases were queried to perform a retrospective analysis of all patients who underwent ICH evacuation with the Apollo system from May 2014 to September 2014 at 4 centers (Medical University of South Carolina, Stony Brook University, University of California at San Diego, and Semmes-Murphy Clinic). Cases were performed either in the neurointerventional suite, operating room, or in a hybrid operating room/angiography suite. Twenty-nine patients (15 female; mean age, 62 ± 12.6 years) underwent the minimally invasive evacuation of ICH. Six of these parenchymal hemorrhages had an additional intraventricular hemorrhage component. The mean volume of ICH was 45.4 ± 30.8 mL, which decreased to 21.8 ± 23.6 mL after evacuation (mean, 54.1 ± 39.1% reduction; P < .001). Two complications directly attributed to the evacuation attempt were encountered (6.9%). The mortality rate was 13.8% (n = 4). Minimally invasive evacuation of ICH and intraventricular hemorrhage can be achieved with the Apollo system. Future work will be required to determine which subset of patients are most likely to benefit from this promising technology.

Steady state method to determine unsaturated hydraulic conductivity at the ambient water potential

DOEpatents

HUbbell, Joel M.

2014-08-19

The present invention relates to a new laboratory apparatus for measuring the unsaturated hydraulic conductivity at a single water potential. One or more embodiments of the invented apparatus can be used over a wide range of water potential values within the tensiometric range, requires minimal laboratory preparation, and operates unattended for extended periods with minimal supervision. The present invention relates to a new laboratory apparatus for measuring the unsaturated hydraulic conductivity at a single water potential. One or more embodiments of the invented apparatus can be used over a wide range of water potential values within the tensiometric range, requires minimal laboratory preparation, and operates unattended for extended periods with minimal supervision.

Clitoral Epidermal Inclusion Cyst Resection With Intraoperative Sensory Nerve Mapping Technique.

PubMed

Wu, Cindy; Damitz, Lynn; Karrat, Kimberly M; Mintz, Alice; Zolnoun, Denniz

2016-01-01

Despite the ever increasing popularity of labial and clitoral surgeries, the best practices and long-term effects of reconstructive procedures in these regions remain unknown. This is particularly noteworthy because the presentation of nerve-related symptoms may be delayed up to a year. Despite the convention that these surgical procedures are low risk, little is known about the best practices that may reduce the postoperative complications as a result of these reconstructive surgeries. We describe a preoperative sensory mapping technique in the context of a symptomatic inclusion cyst in the clitoral region. This technique delineates anatomical and functional regions innervated by the dorsal clitoral nerve while minimizing the vascular watershed area in the midline. A prototypical case of a patient with a clitoral mass is discussed with clinical history and surgical approach. Prior to surgical excision, the dorsal clitoral nerve distribution was mapped in order to avoid a surgical incision in this sensual zone. In our practice, preoperative sensory mapping is a clinically useful planning tool that requires minimal instrumentation and no additional operating time. Sensory mapping allows identification of the functional zone innervated by the dorsal clitoral nerve, which can aid in minimizing damage to the area.

Comparing fixed sampling with minimizer sampling when using k-mer indexes to find maximal exact matches.

PubMed

Almutairy, Meznah; Torng, Eric

2018-01-01

Bioinformatics applications and pipelines increasingly use k-mer indexes to search for similar sequences. The major problem with k-mer indexes is that they require lots of memory. Sampling is often used to reduce index size and query time. Most applications use one of two major types of sampling: fixed sampling and minimizer sampling. It is well known that fixed sampling will produce a smaller index, typically by roughly a factor of two, whereas it is generally assumed that minimizer sampling will produce faster query times since query k-mers can also be sampled. However, no direct comparison of fixed and minimizer sampling has been performed to verify these assumptions. We systematically compare fixed and minimizer sampling using the human genome as our database. We use the resulting k-mer indexes for fixed sampling and minimizer sampling to find all maximal exact matches between our database, the human genome, and three separate query sets, the mouse genome, the chimp genome, and an NGS data set. We reach the following conclusions. First, using larger k-mers reduces query time for both fixed sampling and minimizer sampling at a cost of requiring more space. If we use the same k-mer size for both methods, fixed sampling requires typically half as much space whereas minimizer sampling processes queries only slightly faster. If we are allowed to use any k-mer size for each method, then we can choose a k-mer size such that fixed sampling both uses less space and processes queries faster than minimizer sampling. The reason is that although minimizer sampling is able to sample query k-mers, the number of shared k-mer occurrences that must be processed is much larger for minimizer sampling than fixed sampling. In conclusion, we argue that for any application where each shared k-mer occurrence must be processed, fixed sampling is the right sampling method.

Comparing fixed sampling with minimizer sampling when using k-mer indexes to find maximal exact matches

PubMed Central

Torng, Eric

2018-01-01

Bioinformatics applications and pipelines increasingly use k-mer indexes to search for similar sequences. The major problem with k-mer indexes is that they require lots of memory. Sampling is often used to reduce index size and query time. Most applications use one of two major types of sampling: fixed sampling and minimizer sampling. It is well known that fixed sampling will produce a smaller index, typically by roughly a factor of two, whereas it is generally assumed that minimizer sampling will produce faster query times since query k-mers can also be sampled. However, no direct comparison of fixed and minimizer sampling has been performed to verify these assumptions. We systematically compare fixed and minimizer sampling using the human genome as our database. We use the resulting k-mer indexes for fixed sampling and minimizer sampling to find all maximal exact matches between our database, the human genome, and three separate query sets, the mouse genome, the chimp genome, and an NGS data set. We reach the following conclusions. First, using larger k-mers reduces query time for both fixed sampling and minimizer sampling at a cost of requiring more space. If we use the same k-mer size for both methods, fixed sampling requires typically half as much space whereas minimizer sampling processes queries only slightly faster. If we are allowed to use any k-mer size for each method, then we can choose a k-mer size such that fixed sampling both uses less space and processes queries faster than minimizer sampling. The reason is that although minimizer sampling is able to sample query k-mers, the number of shared k-mer occurrences that must be processed is much larger for minimizer sampling than fixed sampling. In conclusion, we argue that for any application where each shared k-mer occurrence must be processed, fixed sampling is the right sampling method. PMID:29389989

Lunar Reconnaissance Orbiter (LRO) Rapid Thermal Design Development

NASA Technical Reports Server (NTRS)

Baker, Charles; Cottingham, Christine; Garrison, Matthew; Melak, Tony; Peabody, Sharon; Powers, Dan

2009-01-01

The Lunar Reconnaissance Orbiter (LRO) project had a rapid development schedule starting with project conception in spring of 2004, instrument and launch vehicle selection late in 2005 and then launch in early 2009. The lunar thermal environment is one of the harshest in our solar system with the heavy infrared loading of the moon due to low albedo, lack of lunar atmosphere, and low effective regolith conduction. This set of constraints required a thermal design which maximized performance (minimized radiator area and cold control heater power) and minimized thermal hardware build at the orbiter level (blanketing, and heater service). The orbiter design located most of the avionics on an isothermalized heat pipe panel called the IsoThermal Panel (ITP). The ITP was coupled by dual bore heat pipes to an Optical Solar Reflector (OSR) covered heat pipe radiator. By coupling all of the avionics to one system, the hardware was simplified. The seven instruments were mainly heritage instruments which resulted in their desired radiators being located by their heritage design. This minimized instrument redesigns and therefore allowed them to be delivered earlier, though it resulted in a more complex orbiter level blanket and heater service design. Three of the instruments were mounted on a tight pointing M55J optical bench that needed to be covered in heaters to maintain pointing. Two were mounted to spacecraft controlled radiators. One was mounted to the ITP Dual Bores. The last was mounted directly to the bus structure on the moon facing panel. The propulsion system utilized four-20 pound insertion thrusters and eight-5 pound attitude control thrusters (ACS) in addition to 1000 kg of fuel in two large tanks. The propulsion system had a heater cylinder and a heated mounting deck for the insertion thrusters which coupled most of the propulsion design together simplifying the heater design. The High Gain Antenna System (HGAS) and Solar Array System (SAS) used dual axis actuator gimbal systems. HGAS required additional boom heaters to cool the approximately 10 W of RF losses thru the rotary joints and wave guides from the 40 W Ka system. By design this module needed a fair amount of heater, blanketing, and radiator complexity. The SAS system required a separate cable wrap radiator to help cool the Solar Array harness which dissipated 30 W thru the actuators and cable wraps. This module also was complex.

Nursing home medication administration cost minimization analysis.

PubMed

Hamrick, Irene; Nye, Ann Marie; Gardner, Casey K

2007-03-01

To assess the time it takes nurses to administer medications in the nursing home setting, to calculate nursing cost of medication administration, and to determine whether using extended-release products are justified by decreasing nursing costs. Cost-minimization analysis using observational data from a time-motion analysis. Two 150-bed nursing homes in rural eastern North Carolina. Nurses working during first and second shifts. Nurses were timed as they each administered medications to 12 patients. The mean time required to administer each dosage form was calculated. The cost of nursing time was based on the average nursing staff salary of $20.45 per hour as reported by the directors of nursing. Time and cost to dispense one more medication during an existing medication pass and an additional medication pass are calculated. The time to administer an additional dose of an oral medication to one patient was 45.01 seconds during an already scheduled medication pass and 63.05 seconds during a new medication pass. The cost of adding an oral medication once a day for a patient will cost $7.67 per month if administered at the same time as other medications or $10.74 per month if a new medication pass is required. The administration of other dosage forms, such as crushed, percutaneous enteroscopic gastrostomy, injection, and patch was more time involved and, thus, costlier. Formulas are provided to calculate medication administration cost based on local salary. Nursing time and costs for medication administration in the nursing home are great and should be considered when selecting a product. This may justify the selection of higher cost extended-release products.

Risk-based requirements management framework with applications to assurance cases

NASA Astrophysics Data System (ADS)

Feng, D.; Eyster, C.

The current regulatory approach for assuring device safety primarily focuses on compliance with prescriptive safety regulations and relevant safety standards. This approach, however, does not always lead to a safe system design even though safety regulations and standards have been met. In the medical device industry, several high profile recalls involving infusion pumps have prompted the regulatory agency to reconsider how device safety should be managed, reviewed and approved. An assurance case has been cited as a promising tool to address this growing concern. Assurance cases have been used in safety-critical systems for some time. Most assurance cases, if not all, in literature today are developed in an ad hoc fashion, independent from risk management and requirement development. An assurance case is a resource-intensive endeavor that requires additional effort and documentation from equipment manufacturers. Without a well-organized requirements infrastructure in place, such “ additional effort” can be substantial, to the point where the cost of adoption outweighs the benefit of adoption. In this paper, the authors present a Risk-Based Requirements and Assurance Management (RBRAM) methodology. The RBRAM is an elaborate framework that combines Risk-Based Requirements Management (RBRM) with assurance case methods. Such an integrated framework can help manufacturers leverage an existing risk management to present a comprehensive assurance case with minimal additional effort while providing a supplementary means to reexamine the integrity of the system design in terms of the mission objective. Although the example used is from the medical industry, the authors believe that the RBRAM methodology underlines the fundamental principle of risk management, and offers a simple, yet effective framework applicable to aerospace industry, perhaps, to any industry.

Stacked Transformer for Driver Gain and Receive Signal Splitting

NASA Technical Reports Server (NTRS)

Driscoll, Kevin R.

2013-01-01

In a high-speed signal transmission system that uses transformer coupling, there is a need to provide increased transmitted signal strength without adding active components. This invention uses additional transformers to achieve the needed gain. The prior art uses stronger drivers (which require an IC redesign and a higher power supply voltage), or the addition of another active component (which can decrease reliability, increase power consumption, reduce the beneficial effect of serializer/deserializer preemphasis or deemphasis, and/or interfere with fault containment mechanisms), or uses a different transformer winding ratio (which requires redesign of the transformer and may not be feasible with high-speed signals that require a 1:1 winding ratio). This invention achieves the required gain by connecting the secondaries of multiple transformers in series. The primaries of these transformers are currently either connected in parallel or are connected to multiple drivers. There is also a need to split a receive signal to multiple destinations with minimal signal loss. Additional transformers can achieve the split. The prior art uses impedance-matching series resistors that cause a loss of signal. Instead of causing a loss, most instantiations of this invention would actually provide gain. Multiple transformers are used instead of multiple windings on a single transformer because multiple windings on the same transformer would require a redesign of the transformer, and may not be feasible with high-speed transformers that usually require a bifilar winding with a 1:1 ratio. This invention creates the split by connecting the primaries of multiple transformers in series. The secondary of each transformer is connected to one of the intended destinations without the use of impedance-matching series resistors.

Context generalization in Drosophila visual learning requires the mushroom bodies

NASA Astrophysics Data System (ADS)

Liu, Li; Wolf, Reinhard; Ernst, Roman; Heisenberg, Martin

1999-08-01

The world is permanently changing. Laboratory experiments on learning and memory normally minimize this feature of reality, keeping all conditions except the conditioned and unconditioned stimuli as constant as possible. In the real world, however, animals need to extract from the universe of sensory signals the actual predictors of salient events by separating them from non-predictive stimuli (context). In principle, this can be achieved ifonly those sensory inputs that resemble the reinforcer in theirtemporal structure are taken as predictors. Here we study visual learning in the fly Drosophila melanogaster, using a flight simulator,, and show that memory retrieval is, indeed, partially context-independent. Moreover, we show that the mushroom bodies, which are required for olfactory but not visual or tactile learning, effectively support context generalization. In visual learning in Drosophila, it appears that a facilitating effect of context cues for memory retrieval is the default state, whereas making recall context-independent requires additional processing.

Natural SM-like 126 GeV Higgs boson via nondecoupling D terms

DOE PAGES

Bertuzzo, Enrico; Frugiuele, Claudia

2016-02-16

Accommodating both a 126 GeV mass and standard model (SM)-like couplings for the Higgs has a fine-tuning price in supersymmetric models. Examples are the minimal supersymmetric standard model, in which SM-like couplings are natural, but raising the Higgs mass to 126 GeV requires a considerable tuning, and the nonminimal supersymmetric standard model, in which the situation is reversed: the Higgs is naturally heavier, but being SM-like requires some tuning. Finally, we show that models with nondecoupling D terms alleviate this tension—a 126 GeV SM-like Higgs comes out basically with no fine-tuning cost. In addition, the analysis of the fine-tuning of the extended gaugemore » sector shows that naturalness requires the heavy gauge bosons to likely be within the reach of LHC run II.« less

Design of bipolar, flowing-electrolyte zinc-bromine electric-vehicle battery systems

NASA Astrophysics Data System (ADS)

Malachesky, P. A.; Bellows, R. J.; Einstein, H. E.; Grimes, P. G.; Newby, K.; Young, A.

1983-01-01

The integration of bipolar, flowing electrolyte zinc-bromine technology into a viable electric vehicle battery system requires careful analysis of the requirements placed on the battery system by the EV power train. In addition to the basic requirement of an appropriate battery voltage and power density, overall battery system energy efficiency must also be considered and parasitic losses from auxiliaries such as pumps and shunt current protection minimized. An analysis of the influence of these various factors on zinc-bromine EV battery system design has been carried out for two types of EV propulsion systems. The first of these is a nominal 100V dc system, while the second is a high voltage (200V dc) system as might be used with an advanced design ac propulsion system. Battery performance was calculated using an experimentally determined relationship which expresses battery voltage as a function of current density and state-of-charge.

In vitro contraction of cytokinetic ring depends on myosin II but not on actin dynamics.

PubMed

Mishra, Mithilesh; Kashiwazaki, Jun; Takagi, Tomoko; Srinivasan, Ramanujam; Huang, Yinyi; Balasubramanian, Mohan K; Mabuchi, Issei

2013-07-01

Cytokinesis in many eukaryotes involves the contraction of an actomyosin-based contractile ring. However, the detailed mechanism of contractile ring contraction is not fully understood. Here, we establish an experimental system to study contraction of the ring to completion in vitro. We show that the contractile ring of permeabilized fission yeast cells undergoes rapid contraction in an ATP- and myosin-II-dependent manner in the absence of other cytoplasmic constituents. Surprisingly, neither actin polymerization nor its disassembly is required for contraction of the contractile ring, although addition of exogenous actin-crosslinking proteins blocks ring contraction. Using contractile rings generated from fission yeast cytokinesis mutants, we show that not all proteins required for assembly of the ring are required for its contraction in vitro. Our work provides the beginnings of the definition of a minimal contraction-competent cytokinetic ring apparatus.

[Patella fractures in knee arthroplasty].

PubMed

Roth, A; Ghanem, M; Fakler, J

2016-05-01

Periprosthetic patella fractures occur both with and without retropatellar joint replacement. A non-operative treatment yields satisfactory results with low morbidity. It can be applied in minimally displaced fractures that have an intact retropatellar component and an intact extensor mechanism, combined with an initial immobilization. The surgical treatment is associated with relatively poor results and with high complication rates. There was only minor improvement of functional results, no matter which surgical technique was used. Surgical intervention is still required in fractures with a loosening of the patellar component, considerable dislocations of fragments, and damage to or rupture of the extensor mechanism. In particular, type II fractures require repair of the extensor mechanism and the fracture or patellectomy. Type III fractures require a revision or resection of the patella, a patelloplasty or total patellectomy. In addition, early or late reconstruction using allograft to restore the extensor mechanism can be taken in consideration.

Extracellular space preservation aids the connectomic analysis of neural circuits.

PubMed

Pallotto, Marta; Watkins, Paul V; Fubara, Boma; Singer, Joshua H; Briggman, Kevin L

2015-12-09

Dense connectomic mapping of neuronal circuits is limited by the time and effort required to analyze 3D electron microscopy (EM) datasets. Algorithms designed to automate image segmentation suffer from substantial error rates and require significant manual error correction. Any improvement in segmentation error rates would therefore directly reduce the time required to analyze 3D EM data. We explored preserving extracellular space (ECS) during chemical tissue fixation to improve the ability to segment neurites and to identify synaptic contacts. ECS preserved tissue is easier to segment using machine learning algorithms, leading to significantly reduced error rates. In addition, we observed that electrical synapses are readily identified in ECS preserved tissue. Finally, we determined that antibodies penetrate deep into ECS preserved tissue with only minimal permeabilization, thereby enabling correlated light microscopy (LM) and EM studies. We conclude that preservation of ECS benefits multiple aspects of the connectomic analysis of neural circuits.

An Everting Ureteral Access Sheath: Concepts and In Vitro Testing

NASA Astrophysics Data System (ADS)

Lee, Keith L.; Stoller, Marshall L.

2007-04-01

Ureteral access sheaths have been a recent innovation in facilitating ureteral stone surgery. Once properly placed, access sheaths allow the movement of ureteroscopes and other instruments through the ureter with minimal injury to the urothelium. However, there are shortcomings of the current device designs. Initial sheath placement requires significant force, and shear stress can injure the ureter. In addition, inadvertent advancement of the outer sheath without the inner introducer stylet can tear and avulse the ureter. A novel eversion design incorporating a lubricous film provides marked improvement over current access sheaths. In bench top and animal models, the eversion shealths require less force during advancement, cause less injury to the urothelial tissue, and have a lower potential of introducing extraneous materials (e.g., microbes) into a simulated urinary tract. While, the everting design provides important advantages over traditional non-everting designs, further preclinical and clinical trials are required.

Mach 6.5 air induction system design for the Beta 2 two-stage-to-orbit booster vehicle

NASA Technical Reports Server (NTRS)

Midea, Anthony C.

1991-01-01

A preliminary, two-dimensional, mixed compression air induction system is designed for the Beta II Two Stage to Orbit booster vehicle to minimize installation losses and efficiently deliver the required airflow. Design concepts, such as an external isentropic compression ramp and a bypass system were developed and evaluated for performance benefits. The design was optimized by maximizing installed propulsion/vehicle system performance. The resulting system design operating characteristics and performance are presented. The air induction system design has significantly lower transonic drag than similar designs and only requires about 1/3 of the bleed extraction. In addition, the design efficiently provides the integrated system required airflow, while maintaining adequate levels of total pressure recovery. The excellent performance of this highly integrated air induction system is essential for the successful completion of the Beta II booster vehicle mission.

Study of V/STOL aircraft implementation. Volume 1: Summary

NASA Technical Reports Server (NTRS)

Portenier, W. J.; Webb, H. M.

1973-01-01

A high density short haul air market which by 1980 is large enough to support the introduction of an independent short haul air transportation system is discussed. This system will complement the existing air transportation system and will provide relief of noise and congestion problems at conventional airports. The study has found that new aircraft, exploiting V/STOL and quiet engine technology, can be available for implementing these new services, and they can operate from existing reliever and general aviation airports. The study has also found that the major funding requirements for implementing new short haul services could be borne by private capital, and that the government funding requirement would be minimal and/or recovered through the airline ticket tax. In addition, a suitable new short haul aircraft would have a market potential for $3.5 billion in foreign sales. The long lead times needed for aircraft and engine technology development will require timely actions by federal agencies.

Optimal allocation of testing resources for statistical simulations

NASA Astrophysics Data System (ADS)

Quintana, Carolina; Millwater, Harry R.; Singh, Gulshan; Golden, Patrick

2015-07-01

Statistical estimates from simulation involve uncertainty caused by the variability in the input random variables due to limited data. Allocating resources to obtain more experimental data of the input variables to better characterize their probability distributions can reduce the variance of statistical estimates. The methodology proposed determines the optimal number of additional experiments required to minimize the variance of the output moments given single or multiple constraints. The method uses multivariate t-distribution and Wishart distribution to generate realizations of the population mean and covariance of the input variables, respectively, given an amount of available data. This method handles independent and correlated random variables. A particle swarm method is used for the optimization. The optimal number of additional experiments per variable depends on the number and variance of the initial data, the influence of the variable in the output function and the cost of each additional experiment. The methodology is demonstrated using a fretting fatigue example.

The choline requirement of broiler chicks during the seventh week of life.

PubMed

Molitoris, B A; Baker, D H

1976-01-01

Male crossbred chicks were used to quantify the choline requirement and choline-sparing value of methionine and betaine for broiler chicks during the seventh week of life. The sulfur amino acid (SAA) requirement of male and female chicks was also determined. In all assays a crystalline amino acid diet containing 14.9% protein equivalent and 3400 kcal. M.E./kg, was employed. Increasing increments (0.08%) of SAA (equal mixture of DL-methionine and L-cystine) were fed from 0.38 to 0.70% of the diet. Least squares analysis indicated SAA requirements for maximal weight gain of 0.61 and 0.62% of the diet for males and females, respectively. The choline requirement was determined by feeding six levels of choline in the presence of 0.62% SAA. Gain but not gain/feed responded linearly to choline addition. Least squares analysis of gain indicated a dietary choline requirement of 358 p.p.m. of 30.6 mg./day. The choline-replacement value of methionine and betaine was found to be minimal.

DATA QUALITY OBJECTIVES FOR SELECTING WASTE SAMPLES FOR BENCH-SCALE REFORMER TREATABILITY STUDIES

DOE Office of Scientific and Technical Information (OSTI.GOV)

BANNING DL

2011-02-11

This document describes the data quality objectives to select archived samples located at the 222-S Laboratory for Bench-Scale Reforming testing. The type, quantity, and quality of the data required to select the samples for Fluid Bed Steam Reformer testing are discussed. In order to maximize the efficiency and minimize the time to treat Hanford tank waste in the Waste Treatment and Immobilization Plant, additional treatment processes may be required. One of the potential treatment processes is the fluidized bed steam reformer. A determination of the adequacy of the fluidized bed steam reformer process to treat Hanford tank waste is required.more » The initial step in determining the adequacy of the fluidized bed steam reformer process is to select archived waste samples from the 222-S Laboratory that will be used in a bench scale tests. Analyses of the selected samples will be required to confirm the samples meet the shipping requirements and for comparison to the bench scale reformer (BSR) test sample selection requirements.« less

Nitrogen removal by recycle water nitritation as an attractive alternative for retrofit technologies in municipal wastewater treatment plants.

PubMed

Gil, K I; Choi, E

2004-01-01

The recycle water from sludge processing in municipal wastewater treatment plants causes many serious problems in the efficiency and stability of the mainstream process. Thus, the design approach for recycle water is an important part of any biological nutrient removal system design when a retrofit technology is required for upgrading an existing plant. Moreover, the application of nitrogen removal from recycle water using the nitritation process has recently increased due to economic reasons associated with an effective carbon allocation as well as the minimization of aeration costs. However, for the actual application of recycle water nitritation, it has not been fully examined whether or not additional volume would be required in an existing plant. In this paper, the addition of recycle water nitritation to an existing plant was evaluated based on a volume analysis and estimation of final effluent quality. It was expected that using the reserve volume of the aeration tank in existing plants, recycle water nitritation could be applied to a plant without any enlargement. With the addition of recycle water nitritation, it was estimated that the final effluent quality would be improved and stabilized, especially in the winter season.

Robotic partial nephrectomy for complex renal tumors: surgical technique.

PubMed

Rogers, Craig G; Singh, Amar; Blatt, Adam M; Linehan, W Marston; Pinto, Peter A

2008-03-01

Laparoscopic partial nephrectomy requires advanced training to accomplish tumor resection and renal reconstruction while minimizing warm ischemia times. Complex renal tumors add an additional challenge to a minimally invasive approach to nephron-sparing surgery. We describe our technique, illustrated with video, of robotic partial nephrectomy for complex renal tumors, including hilar, endophytic, and multiple tumors. Robotic assistance was used to resect 14 tumors in eight patients (mean age: 50.3 yr; range: 30-68 yr). Three patients had hereditary kidney cancer. All patients had complex tumor features, including hilar tumors (n=5), endophytic tumors (n=4), and/or multiple tumors (n=3). Robotic partial nephrectomy procedures were performed successfully without complications. Hilar clamping was used with a mean warm ischemia time of 31 min (range: 24-45 min). Mean blood loss was 230 ml (range: 100-450 ml). Histopathology confirmed clear-cell renal cell carcinoma (n=3), hybrid oncocytic tumor (n=2), chromophobe renal cell carcinoma (n=2), and oncocytoma (n=1). All patients had negative surgical margins. Mean index tumor size was 3.6 cm (range: 2.6-6.4 cm). Mean hospital stay was 2.6 d. At 3-mo follow-up, no patients experienced a statistically significant change in serum creatinine or estimated glomerular filtration rate and there was no evidence of tumor recurrence. Robotic partial nephrectomy is safe and feasible for select patients with complex renal tumors, including hilar, endophytic, and multiple tumors. Robotic assistance may facilitate a minimally invasive, nephron-sparing approach for select patients with complex renal tumors who might otherwise require open surgery or total nephrectomy.

Multiple needle puncturing: balancing the varus knee.

PubMed

Bellemans, Johan

2011-09-09

The so-called "pie crusting" technique using multiple stab incisions is a well-established procedure for correcting tightness of the iliotibial band in the valgus knee. It is, however, not applicable for balancing the medial side in varus knees because of the risk for iatrogenic transsection of the medial collateral ligament (MCL). This article presents our experience with a safer alternative and minimally invasive technique for medial soft tissue balancing, where we make multiple punctures in the MCL using a 19-gauge needle to progressively stretch the MCL until a correct ligament balance is achieved. Our technique requires minimal to no additional soft tissue dissection and can even be performed percutaneously when necessary. This technique, therefore, does not impact the length of the skin or soft tissue incisions. We analyzed 61 cases with varus deformity that were intraoperatively treated using this technique. In 4 other cases, the technique was used as a percutaneous procedure to correct postoperative medial tightness that caused persistent pain on the medial side. The procedure was considered successful when a 2- to 4-mm mediolateral joint line opening was obtained in extension and 2 to 6 mm in flexion. In 62 cases (95%), a progressive correction of medial tightness was achieved according to the above-described criteria. Three cases were overreleased and required compensatory release of the lateral structures and use of a thicker insert. Based on these results, we consider needle puncturing an effective and safe technique for progressive correction of MCL tightness during minimally invasive total knee arthroplasty. Copyright 2011, SLACK Incorporated.

A comprehensive program to minimize platelet outdating.

PubMed

Fuller, Alice K; Uglik, Kristin M; Braine, Hayden G; King, Karen E

2011-07-01

Platelet (PLT) transfusions are essential for patients who are bleeding or have an increased risk of bleeding due to a decreased number or abnormal function of circulating PLTs. A shelf life of 5 days for PLT products presents an inventory management challenge. In 2006, greater than 10% of apheresis PLTs made in the United States outdated. It is imperative to have a sufficient number of products for patients requiring transfusion, but outdating PLTs is a financial burden and a waste of a resource. We present the approach used in our institution to anticipate inventory needs based on current patient census and usage. Strategies to predict usage and to identify changes in anticipated usage are examined. Annual outdating is reviewed for a 10-year period from 2000 through 2009. From January 1, 2000, through December 2009, there were 128,207 PLT transfusions given to 15,265 patients. The methods used to anticipate usage and adjust inventory resulted in an annual outdate rate of approximately 1% for the 10-year period reviewed. In addition we have not faced situations where inventory was inadequate to meet the needs of the patients requiring transfusions. We have identified three elements of our transfusion service that can minimize outdate: a knowledgeable proactive staff dedicated to PLT management, a comprehensive computer-based transfusion history for each patient, and a strong two-way relationship with the primary product supplier. Through our comprehensive program, based on the principles of providing optimal patient care, we have minimized PLT outdating for more than 10 years. © 2011 American Association of Blood Banks.

A lightweight distributed framework for computational offloading in mobile cloud computing.

PubMed

Shiraz, Muhammad; Gani, Abdullah; Ahmad, Raja Wasim; Adeel Ali Shah, Syed; Karim, Ahmad; Rahman, Zulkanain Abdul

2014-01-01

The latest developments in mobile computing technology have enabled intensive applications on the modern Smartphones. However, such applications are still constrained by limitations in processing potentials, storage capacity and battery lifetime of the Smart Mobile Devices (SMDs). Therefore, Mobile Cloud Computing (MCC) leverages the application processing services of computational clouds for mitigating resources limitations in SMDs. Currently, a number of computational offloading frameworks are proposed for MCC wherein the intensive components of the application are outsourced to computational clouds. Nevertheless, such frameworks focus on runtime partitioning of the application for computational offloading, which is time consuming and resources intensive. The resource constraint nature of SMDs require lightweight procedures for leveraging computational clouds. Therefore, this paper presents a lightweight framework which focuses on minimizing additional resources utilization in computational offloading for MCC. The framework employs features of centralized monitoring, high availability and on demand access services of computational clouds for computational offloading. As a result, the turnaround time and execution cost of the application are reduced. The framework is evaluated by testing prototype application in the real MCC environment. The lightweight nature of the proposed framework is validated by employing computational offloading for the proposed framework and the latest existing frameworks. Analysis shows that by employing the proposed framework for computational offloading, the size of data transmission is reduced by 91%, energy consumption cost is minimized by 81% and turnaround time of the application is decreased by 83.5% as compared to the existing offloading frameworks. Hence, the proposed framework minimizes additional resources utilization and therefore offers lightweight solution for computational offloading in MCC.

A Lightweight Distributed Framework for Computational Offloading in Mobile Cloud Computing

PubMed Central

Shiraz, Muhammad; Gani, Abdullah; Ahmad, Raja Wasim; Adeel Ali Shah, Syed; Karim, Ahmad; Rahman, Zulkanain Abdul

2014-01-01

The latest developments in mobile computing technology have enabled intensive applications on the modern Smartphones. However, such applications are still constrained by limitations in processing potentials, storage capacity and battery lifetime of the Smart Mobile Devices (SMDs). Therefore, Mobile Cloud Computing (MCC) leverages the application processing services of computational clouds for mitigating resources limitations in SMDs. Currently, a number of computational offloading frameworks are proposed for MCC wherein the intensive components of the application are outsourced to computational clouds. Nevertheless, such frameworks focus on runtime partitioning of the application for computational offloading, which is time consuming and resources intensive. The resource constraint nature of SMDs require lightweight procedures for leveraging computational clouds. Therefore, this paper presents a lightweight framework which focuses on minimizing additional resources utilization in computational offloading for MCC. The framework employs features of centralized monitoring, high availability and on demand access services of computational clouds for computational offloading. As a result, the turnaround time and execution cost of the application are reduced. The framework is evaluated by testing prototype application in the real MCC environment. The lightweight nature of the proposed framework is validated by employing computational offloading for the proposed framework and the latest existing frameworks. Analysis shows that by employing the proposed framework for computational offloading, the size of data transmission is reduced by 91%, energy consumption cost is minimized by 81% and turnaround time of the application is decreased by 83.5% as compared to the existing offloading frameworks. Hence, the proposed framework minimizes additional resources utilization and therefore offers lightweight solution for computational offloading in MCC. PMID:25127245

Multipass Target Search in Natural Environments

PubMed Central

Otte, Michael W.; Sofge, Donald; Gupta, Satyandra K.

2017-01-01

Consider a disaster scenario where search and rescue workers must search difficult to access buildings during an earthquake or flood. Often, finding survivors a few hours sooner results in a dramatic increase in saved lives, suggesting the use of drones for expedient rescue operations. Entropy can be used to quantify the generation and resolution of uncertainty. When searching for targets, maximizing mutual information of future sensor observations will minimize expected target location uncertainty by minimizing the entropy of the future estimate. Motion planning for multi-target autonomous search requires planning over an area with an imperfect sensor and may require multiple passes, which is hindered by the submodularity property of mutual information. Further, mission duration constraints must be handled accordingly, requiring consideration of the vehicle’s dynamics to generate feasible trajectories and must plan trajectories spanning the entire mission duration, something which most information gathering algorithms are incapable of doing. If unanticipated changes occur in an uncertain environment, new plans must be generated quickly. In addition, planning multipass trajectories requires evaluating path dependent rewards, requiring planning in the space of all previously selected actions, compounding the problem. We present an anytime algorithm for autonomous multipass target search in natural environments. The algorithm is capable of generating long duration dynamically feasible multipass coverage plans that maximize mutual information using a variety of techniques such as ϵ-admissible heuristics to speed up the search. To the authors’ knowledge this is the first attempt at efficiently solving multipass target search problems of such long duration. The proposed algorithm is based on best first branch and bound and is benchmarked against state of the art algorithms adapted to the problem in natural Simplex environments, gathering the most information in the given search time. PMID:29099087

Design for pressure regulating components

NASA Technical Reports Server (NTRS)

Wichmann, H.

1973-01-01

The design development for Pressure Regulating Components included a regulator component trade-off study with analog computer performance verification to arrive at a final optimized regulator configuration for the Space Storable Propulsion Module, under development for a Jupiter Orbiter mission. This application requires the pressure regulator to be capable of long-term fluorine exposure. In addition, individual but basically identical (for purposes of commonality) units are required for separate oxidizer and fuel pressurization. The need for dual units requires improvement in the regulation accuracy over present designs. An advanced regulator concept was prepared featuring redundant bellows, all metallic/ceramic construction, friction-free guidance of moving parts, gas damping, and the elimination of coil springs normally used for reference forces. The activities included testing of actual size seat/poppet components to determine actual discharge coefficients and flow forces. The resulting data was inserted into the computer model of the regulator. Computer simulation of the propulsion module performance over two mission profiles indicated satisfactory minimization of propellant residual requirements imposed by regulator performance uncertainties.

43 CFR 3272.12 - What environmental protection measures must I include in my utilization plan?

Code of Federal Regulations, 2014 CFR

2014-10-01

... resources; (6) Minimize air and noise pollution; and (7) Minimize hazards to public health and safety during... operations to ensure that they comply with the requirements of § 3200.4, and applicable noise, air, and water... may require you to collect data concerning existing air and water quality, noise, seismicity...

43 CFR 3272.12 - What environmental protection measures must I include in my utilization plan?

Code of Federal Regulations, 2013 CFR

2013-10-01

... resources; (6) Minimize air and noise pollution; and (7) Minimize hazards to public health and safety during... operations to ensure that they comply with the requirements of § 3200.4, and applicable noise, air, and water... may require you to collect data concerning existing air and water quality, noise, seismicity...

43 CFR 3272.12 - What environmental protection measures must I include in my utilization plan?

Code of Federal Regulations, 2012 CFR

2012-10-01

... resources; (6) Minimize air and noise pollution; and (7) Minimize hazards to public health and safety during... operations to ensure that they comply with the requirements of § 3200.4, and applicable noise, air, and water... may require you to collect data concerning existing air and water quality, noise, seismicity...

Robotic unclamped "minimal-margin" partial nephrectomy: ongoing refinement of the anatomic zero-ischemia concept.

PubMed

Satkunasivam, Raj; Tsai, Sheaumei; Syan, Sumeet; Bernhard, Jean-Christophe; de Castro Abreu, Andre Luis; Chopra, Sameer; Berger, Andre K; Lee, Dennis; Hung, Andrew J; Cai, Jie; Desai, Mihir M; Gill, Inderbir S

2015-10-01

Anatomic partial nephrectomy (PN) techniques aim to decrease or eliminate global renal ischemia. To report the technical feasibility of completely unclamped "minimal-margin" robotic PN. We also illustrate the stepwise evolution of anatomic PN surgery with related outcomes data. This study was a retrospective analysis of 179 contemporary patients undergoing anatomic PN at a tertiary academic institution between October 2009 and February 2013. Consecutive consented patients were grouped into three cohorts: group 1, with superselective clamping and developmental-curve experience (n = 70); group 2, with superselective clamping and mature experience (n = 60); and group 3, which had completely unclamped, minimal-margin PN (n = 49). Patients in groups 1 and 2 underwent superselective tumor-specific devascularization, whereas patients in group 3 underwent completely unclamped minimal-margin PN adjacent to the tumor edge, a technique that takes advantage of the radially oriented intrarenal architecture and anatomy. Primary outcomes assessed the technical feasibility of robotic, completely unclamped, minimal-margin PN; short-term changes in estimated glomerular filtration rate (eGFR); and development of new-onset chronic kidney disease (CKD) stage >3. Secondary outcome measures included perioperative variables, 30-d complications, and histopathologic outcomes. Demographic data were similar among groups. For similarly sized tumors (p = 0.13), percentage of kidney preserved was greater (p = 0.047) and margin width was narrower (p = 0.0004) in group 3. In addition, group 3 had less blood loss (200, 225, and 150ml; p = 0.04), lower transfusion rates (21%, 23%, and 4%; p = 0.008), and shorter hospital stay (p = 0.006), whereas operative time and 30-d complication rates were similar. At 1-mo postoperatively, median percentage reduction in eGFR was similar (7.6%, 0%, and 3.0%; p = 0.53); however, new-onset CKD stage >3 occurred less frequently in group 3 (23%, 10%, and 2%; p = 0.003). Study limitations included retrospective analysis, small sample size, and short follow-up. We developed an anatomically based technique of robotic, unclamped, minimal-margin PN. This evolution from selective clamped to unclamped PN may further optimize functional outcomes but requires external validation and longer follow-up. The technical evolution of partial nephrectomy surgery is aimed at eliminating global renal damage from the cessation of blood flow. An unclamped minimal-margin technique is described and may offer renal functional advantage but requires long-term follow-up and validation at other institutions. Copyright © 2015 European Association of Urology. Published by Elsevier B.V. All rights reserved.

Endometrial ablation: normal appearance and complications.

PubMed

Drylewicz, Monica R; Robinson, Kathryn; Siegel, Cary Lynn

2018-03-14

Global endometrial ablation is a commonly performed, minimally invasive technique aimed at improving/resolving abnormal uterine bleeding and menorrhagia in women. As non-resectoscopic techniques have come into existence, endometrial ablation performance continues to increase due to accessibility and decreased requirements for operating room time and advanced technical training. The increased utilization of this method translates into increased imaging of patients who have undergone the procedure. An understanding of the expected imaging appearances of endometrial ablation using different modalities is important for the abdominal radiologist. In addition, the frequent usage of the technique naturally comes with complications requiring appropriate imaging work-up. We review the expected appearance of the post-endometrial ablated uterus on multiple imaging modalities and demonstrate the more common and rare complications seen in the immediate post-procedural time period and remotely.

Superfund record of decision (EPA Region 3): Dover Air Force Base, Oil/Water Separator at Building 918 (Site ot 40), Kent County, DE, March 28, 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-02-01

The Record of Decision presents the selected remedial action for the Oil/Water separator at Building 918 Operable Unit (Site OT 40). There are hazardous substances present in the shallow groundwater at levels below those that would cause risk. Additionally, arsenic and lead exist in soils at levels within regional background levels. The site poses a minimal risk to public health, welfare, and the environment. The No Action alternative requires no actions be taken at the site. This alternative serves as a baseline for comparison and CERCLA requires it be evaluated. It is the preferred alternative at this site because themore » other alternatives offer no substantial advantages.« less

LAURA Users Manual: 5.3-48528

NASA Technical Reports Server (NTRS)

Mazaheri, Alireza; Gnoffo, Peter A.; Johnston, Chirstopher O.; Kleb, Bil

2010-01-01

This users manual provides in-depth information concerning installation and execution of LAURA, version 5. LAURA is a structured, multi-block, computational aerothermodynamic simulation code. Version 5 represents a major refactoring of the original Fortran 77 LAURA code toward a modular structure afforded by Fortran 95. The refactoring improved usability and maintainability by eliminating the requirement for problem-dependent re-compilations, providing more intuitive distribution of functionality, and simplifying interfaces required for multi-physics coupling. As a result, LAURA now shares gas-physics modules, MPI modules, and other low-level modules with the FUN3D unstructured-grid code. In addition to internal refactoring, several new features and capabilities have been added, e.g., a GNU-standard installation process, parallel load balancing, automatic trajectory point sequencing, free-energy minimization, and coupled ablation and flowfield radiation.

LAURA Users Manual: 5.5-64987

NASA Technical Reports Server (NTRS)

Mazaheri, Alireza; Gnoffo, Peter A.; Johnston, Christopher O.; Kleb, William L.

2013-01-01

This users manual provides in-depth information concerning installation and execution of LAURA, version 5. LAURA is a structured, multi-block, computational aerothermodynamic simulation code. Version 5 represents a major refactoring of the original Fortran 77 LAURA code toward a modular structure afforded by Fortran 95. The refactoring improved usability and maintain ability by eliminating the requirement for problem dependent recompilations, providing more intuitive distribution of functionality, and simplifying interfaces required for multi-physics coupling. As a result, LAURA now shares gas-physics modules, MPI modules, and other low-level modules with the Fun3D unstructured-grid code. In addition to internal refactoring, several new features and capabilities have been added, e.g., a GNU standard installation process, parallel load balancing, automatic trajectory point sequencing, free-energy minimization, and coupled ablation and flowfield radiation.

LAURA Users Manual: 5.4-54166

NASA Technical Reports Server (NTRS)

Mazaheri, Alireza; Gnoffo, Peter A.; Johnston, Christopher O.; Kleb, Bil

2011-01-01

This users manual provides in-depth information concerning installation and execution of Laura, version 5. Laura is a structured, multi-block, computational aerothermodynamic simulation code. Version 5 represents a major refactoring of the original Fortran 77 Laura code toward a modular structure afforded by Fortran 95. The refactoring improved usability and maintainability by eliminating the requirement for problem dependent re-compilations, providing more intuitive distribution of functionality, and simplifying interfaces required for multi-physics coupling. As a result, Laura now shares gas-physics modules, MPI modules, and other low-level modules with the Fun3D unstructured-grid code. In addition to internal refactoring, several new features and capabilities have been added, e.g., a GNU-standard installation process, parallel load balancing, automatic trajectory point sequencing, free-energy minimization, and coupled ablation and flowfield radiation.

LAURA Users Manual: 5.2-43231

NASA Technical Reports Server (NTRS)

Mazaheri, Alireza; Gnoffo, Peter A.; Johnston, Christopher O.; Kleb, Bil

2009-01-01

This users manual provides in-depth information concerning installation and execution of LAURA, version 5. LAURA is a structured, multi-block, computational aerothermodynamic simulation code. Version 5 represents a major refactoring of the original Fortran 77 LAURA code toward a modular structure afforded by Fortran 95. The refactoring improved usability and maintainability by eliminating the requirement for problem-dependent re-compilations, providing more intuitive distribution of functionality, and simplifying interfaces required for multiphysics coupling. As a result, LAURA now shares gas-physics modules, MPI modules, and other low-level modules with the FUN3D unstructured-grid code. In addition to internal refactoring, several new features and capabilities have been added, e.g., a GNU-standard installation process, parallel load balancing, automatic trajectory point sequencing, free-energy minimization, and coupled ablation and flowfield radiation.

Laura Users Manual: 5.1-41601

NASA Technical Reports Server (NTRS)

Mazaheri, Alireza; Gnoffo, Peter A.; Johnston, Christopher O.; Kleb, Bil

2009-01-01

This users manual provides in-depth information concerning installation and execution of LAURA, version 5. LAURA is a structured, multi-block, computational aerothermodynamic simulation code. Version 5 represents a major refactoring of the original Fortran 77 LAURA code toward a modular structure afforded by Fortran 95. The refactoring improved usability and maintainability by eliminating the requirement for problem-dependent re-compilations, providing more intuitive distribution of functionality, and simplifying interfaces required for multiphysics coupling. As a result, LAURA now shares gas-physics modules, MPI modules, and other low-level modules with the FUN3D unstructured-grid code. In addition to internal refactoring, several new features and capabilities have been added, e.g., a GNU-standard installation process, parallel load balancing, automatic trajectory point sequencing, free-energy minimization, and coupled ablation and flowfield radiation.

Experimental demonstration of cheap and accurate phase estimation

NASA Astrophysics Data System (ADS)

Rudinger, Kenneth; Kimmel, Shelby; Lobser, Daniel; Maunz, Peter

We demonstrate experimental implementation of robust phase estimation (RPE) to learn the phases of X and Y rotations on a trapped Yb+ ion qubit.. Unlike many other phase estimation protocols, RPE does not require ancillae nor near-perfect state preparation and measurement operations. Additionally, its computational requirements are minimal. Via RPE, using only 352 experimental samples per phase, we estimate phases of implemented gates with errors as small as 10-4 radians, as validated using gate set tomography. We also demonstrate that these estimates exhibit Heisenberg scaling in accuracy. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

Detecting Chemically Modified DNA Bases Using Surface Enhanced Raman Spectroscopy

PubMed Central

Barhoumi, Aoune; Halas, Naomi J.

2013-01-01

Post-translational modifications of DNA- changes in the chemical structure of individual bases that occur without changes in the DNA sequence- are known to alter gene expression. They are believed to result in frequently deleterious phenotypic changes, such as cancer. Methylation of adenine, methylation and hydroxymethylation of cytosine, and guanine oxidation are the primary DNA base modifications identified to date. Here we show it is possible to use surface enhanced Raman spectroscopy (SERS) to detect these primary DNA base modifications. SERS detection of modified DNA bases is label-free and requires minimal additional sample preparation, reducing the possibility of additional chemical modifications induced prior to measurement. This approach shows the feasibility of DNA base modification assessment as a potentially routine analysis that may be further developed for clinical diagnostics. PMID:24427449

Detecting Chemically Modified DNA Bases Using Surface Enhanced Raman Spectroscopy.

PubMed

Barhoumi, Aoune; Halas, Naomi J

2011-12-15

Post-translational modifications of DNA- changes in the chemical structure of individual bases that occur without changes in the DNA sequence- are known to alter gene expression. They are believed to result in frequently deleterious phenotypic changes, such as cancer. Methylation of adenine, methylation and hydroxymethylation of cytosine, and guanine oxidation are the primary DNA base modifications identified to date. Here we show it is possible to use surface enhanced Raman spectroscopy (SERS) to detect these primary DNA base modifications. SERS detection of modified DNA bases is label-free and requires minimal additional sample preparation, reducing the possibility of additional chemical modifications induced prior to measurement. This approach shows the feasibility of DNA base modification assessment as a potentially routine analysis that may be further developed for clinical diagnostics.

Additive manufacturing of hierarchical injectable scaffolds for tissue engineering.

PubMed

Béduer, A; Piacentini, N; Aeberli, L; Da Silva, A; Verheyen, C A; Bonini, F; Rochat, A; Filippova, A; Serex, L; Renaud, P; Braschler, T

2018-06-05

We present a 3D-printing technology allowing free-form fabrication of centimetre-scale injectable structures for minimally invasive delivery. They result from the combination of 3D printing onto a cryogenic substrate and optimisation of carboxymethylcellulose-based cryogel inks. The resulting highly porous and elastic cryogels are biocompatible, and allow for protection of cell viability during compression for injection. Implanted into the murine subcutaneous space, they are colonized with a loose fibrovascular tissue with minimal signs of inflammation and remain encapsulation-free at three months. Finally, we vary local pore size through control of the substrate temperature during cryogenic printing. This enables control over local cell seeding density in vitro and over vascularization density in cell-free scaffolds in vivo. In sum, we address the need for 3D-bioprinting of large, yet injectable and highly biocompatible scaffolds and show modulation of the local response through control over local pore size. This work combines the power of 3D additive manufacturing with clinically advantageous minimally invasive delivery. We obtain porous, highly compressible and mechanically rugged structures by optimizing a cryogenic 3D printing process. Only a basic commercial 3D printer and elementary control over reaction rate and freezing are required. The porous hydrogels obtained are capable of withstanding delivery through capillaries up to 50 times smaller than their largest linear dimension, an as yet unprecedented compression ratio. Cells seeded onto the hydrogels are protected during compression. The hydrogel structures further exhibit excellent biocompatibility 3 months after subcutaneous injection into mice. We finally demonstrate that local modulation of pore size grants control over vascularization density in vivo. This provides proof-of-principle that meaningful biological information can be encoded during the 3D printing process, deploying its effect after minimally invasive implantation. Copyright © 2018 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Nutritional strategies to combat Salmonella in mono-gastric food animal production.

PubMed

Berge, A C; Wierup, M

2012-04-01

Nutritional strategies to minimize Salmonella in food animal production are one of the key components in producing safer food. The current European approach is to use a farm-to-fork strategy, where each sector must implement measures to minimize and reduce Salmonella contamination. In the pre-harvest phase, this means that all available tools need to be used such as implementation of biosecurity measures, control of Salmonella infections in animals at the farm as well as in transport and trade, optimal housing and management including cleaning, disinfection procedures as well as efforts to achieve Salmonella-free feed production. This paper describes some nutritional strategies that could be used in farm control programmes in the major mono-gastric food production animals: poultry and pigs. Initially, it is important to prevent the introduction of Salmonella onto the farm through Salmonella-contaminated feed and this risk is reduced through heat treatment and the use of organic acids and their salts and formaldehyde. Microbiological sampling and monitoring for Salmonella in the feed mills is required to minimize the introduction of Salmonella via feed onto the farm. In addition, feed withdrawal may create a stressful situation in animals, resulting in an increase in Salmonella shedding. Physical feed characteristics such as coarse-ground meal to pigs can delay gastric emptying, thereby increasing the acidity of the gut and thus reducing the possible prevalence of Salmonella. Coarse-ground grains and access to litter have also been shown to decrease Salmonella shedding in poultry. The feed can also modify the gastro-intestinal tract microflora and influence the immune system, which can minimize Salmonella colonization and shedding. Feed additives, such as organic acids, short- and medium-chain fatty acids, probiotics, including competitive exclusion cultures, prebiotics and certain specific carbohydrates, such as mannan-based compounds, egg proteins, essential oils and bacteriophages, have the potential to reduce Salmonella levels when added to the feed. These nutritional strategies could be evaluated and used in farm control programmes.

LST and instrument considerations. [modular design

NASA Technical Reports Server (NTRS)

Levin, G. M.

1974-01-01

In order that the LST meet its scientific objectives and also be a National Astronomical Space Facility during the 1980's and 1990's, broad requirements have been levied by the scientific community. These scientific requirements can be directly translated into design requirements and specifications for the scientific instruments. The instrument ensemble design must be consistent with a 15-year operational lifetime. Downtime for major repair/refurbishment or instrument updating must be minimized. The overall efficiency and performance of the instruments should be maximized. Modularization of instruments and instrument subsystems, some degree of on-orbit servicing (both repair and replacement), on-axis location, minimizing the number of reflections within instruments, minimizing polarization effects, and simultaneous operation of the F/24 camera with other instruments, are just a few of the design guidelines and specifications which can and will be met in order that these broader scientific requirements be satisfied.-

Payload/orbiter contamination control assessment support

NASA Technical Reports Server (NTRS)

Rantanen, R. O.; Ress, E. B.

1975-01-01

The development and use is described of a basic contamination mathematical model of the shuttle orbiter which incorporates specific shuttle orbiter configurations and contamination sources. These configurations and sources were evaluated with respect to known shuttle orbiter operational surface characteristics and specific lines-of-sight which encompass the majority of viewing requirements for shuttle payloads. The results of these evaluations are presented as summary tables for each major source. In addition, contamination minimization studies were conducted and recommendations are made, where applicable, to support the shuttle orbiter design and operational planning for those sources which were identified to present a significant contamination threat.

Distributed control topologies for deep space formation flying spacecraft

NASA Technical Reports Server (NTRS)

Hadaegh, F. Y.; Smith, R. S.

2002-01-01

A formation of satellites flying in deep space can be specified in terms of the relative satellite positions and absolute satellite orientations. The redundancy in the relative position specification generates a family of control topologies with equivalent stability and reference tracking performance, one of which can be implemented without requiring communication between the spacecraft. A relative position design formulation is inherently unobservable, and a methodology for circumventing this problem is presented. Additional redundancy in the control actuation space can be exploited for feed-forward control of the formation centroid's location in space, or for minimization of total fuel consumption.

On the Isolation of Science Payloads from Spacecraft Vibrations

NASA Technical Reports Server (NTRS)

Sparks, Dean W.; Horta, Lucas G.; Elliott, Kenny B.; Belvin, W. Keith

1995-01-01

The remote sensing of the Earth's features from space requires precision pointing of scientific instruments. To this end, the NASA Langley Research Center has been involved in developing numerous controlled structures technologies. This paper describes one of the more promising technologies for minimizing pointing jitter, namely, payload isolation. The application of passive and active payload mounts for attenuation of pointing jitter of the EOS AM-1 spacecraft is discussed. In addition, analysis and ground tests to validate the performance of isolation mounts using a scaled dynamics model of the EOS AM-1 spacecraft are presented.

Multiple sclerosis.

PubMed

Files, Daniel Kane; Jausurawong, Tani; Katrajian, Ruba; Danoff, Robert

2015-06-01

Multiple sclerosis (MS) is a chronic, debilitating disease that can have devastating effects. Presentation varies widely in symptoms, pace, and progression. In addition to a thorough history and physical examination, diagnostic tools required to diagnose MS and exclude other diagnoses include MRI, evoked potential testing, and cerebrospinal fluid analysis. Although the disease is not curable presently, quality of life can be improved by minimizing the frequency and severity of disease burden. Disease modification, symptom management, preservation of function, and treatment of psychosocial issues are paramount to enhance the quality of life for the patient affected with MS. Copyright © 2015 Elsevier Inc. All rights reserved.

NPAC-Nozzle Performance Analysis Code

NASA Technical Reports Server (NTRS)

Barnhart, Paul J.

1997-01-01

A simple and accurate nozzle performance analysis methodology has been developed. The geometry modeling requirements are minimal and very flexible, thus allowing rapid design evaluations. The solution techniques accurately couple: continuity, momentum, energy, state, and other relations which permit fast and accurate calculations of nozzle gross thrust. The control volume and internal flow analyses are capable of accounting for the effects of: over/under expansion, flow divergence, wall friction, heat transfer, and mass addition/loss across surfaces. The results from the nozzle performance methodology are shown to be in excellent agreement with experimental data for a variety of nozzle designs over a range of operating conditions.

Entanglement witnessing and quantum cryptography with nonideal ferromagnetic detectors

NASA Astrophysics Data System (ADS)

Kłobus, Waldemar; Grudka, Andrzej; Baumgartner, Andreas; Tomaszewski, Damian; Schönenberger, Christian; Martinek, Jan

2014-03-01

We investigate theoretically the use of nonideal ferromagnetic contacts as a means to detect quantum entanglement of electron spins in transport experiments. We use a designated entanglement witness and find a minimal spin polarization of η >1/√3 ≈58% required to demonstrate spin entanglement. This is significantly less stringent than the ubiquitous tests of Bell's inequality with η >1/√24 >≈84%. In addition, we discuss the impact of decoherence and noise on entanglement detection and apply the presented framework to a simple quantum cryptography protocol. Our results are directly applicable to a large variety of experiments.

A Concept for Power Cycling the Electronics of CALICE-AHCAL with the Train Structure of ILC

NASA Astrophysics Data System (ADS)

Göottlicher, Peter; The Calice-Collaboration

Particle flow algorithm calorimetry requires high granularity three-dimensional readout. The tight power requirement of 40 μW/channel is reached by enabling readout ASIC currents only during beam delivery, corresponding to a 1% duty cycle. EMI noise caused by current switching needs to be minimized by the power system and this paper presents ideas, simulations and first measurements for minimizing disturbances. A carefully design of circuits, printed circuit boards, grounding scheme and use of floating supplies allows current loops to be closed locally, stabilized voltages and minimal currents in the metal structures.

Rectoanal repair versus suture haemorrhoidopexy: a comparative study on suture mucopexy procedures for high-grade haemorrhoids.

PubMed

Theodoropoulos, G E; Michalopoulos, N V; Linardoutsos, D; Stamopoulos, P; Flessas, I; Tsamis, D; Zografos, G C

2012-06-01

The isolated application of Doppler-guided haemorrhoidal artery ligation (DGHAL) may fail due to the increased reprolapse rate for high-grade haemorrhoids. DGHAL has been combined with a proctoscopic-assisted transanal rectal mucopexy of the prolapsing tissue. The technique is called rectoanal repair (RAR) and is an evolution of various mucopexy and suture haemorrhoidopexy (SHP) techniques. A prominent external component may require minimal (muco-) cutaneous excision (MMCE) of protruding anoderm or minor cutaneous excision of skin tags. Fifty-seven patients with symptomatic Goligher grade III and IV haemorrhoids underwent DGHAL followed by either RAR or SHP. In 26 cases, the addition of MMCE was necessary. No significant differences were observed between the two approaches with regards to pain scores measured with visual analogue scale (VAS). On postoperative day 1, mean pain score at rest was 5.81 (±2.23 SD) after SHP versus 5.08 (±2.35 SD) after RAR, while mean pain score at first defecation was 7.31 (±1.6 SD) versus 7.52 (±1.83 SD). There was no difference in the duration of analgesic requirements, postoperative complications and residual prolapse between the 2 procedures. The addition of MMCE did not affect postoperative pain nor analgesic requirements. With the exception of 8 patients who still had with skin tags or minimal protrusion, the remaining of patients (86 %) were asymptomatic and recurrence-free at an average follow-up of 20 months. Overall, 94.8 % of patients stated that they were satisfied with the results, and 91.2 % that they would repeat it if necessary. Performance of either SHP or RAR after DGHAL is a safe and effective surgical tactic for advanced grade haemorrhoids. Our initial results do not confirm any superiority of RAR over traditional SHP.

A Minimal Nitrogen Fixation Gene Cluster from Paenibacillus sp. WLY78 Enables Expression of Active Nitrogenase in Escherichia coli

PubMed Central

Zhao, Dehua; Liu, Xiaomeng; Zhang, Bo; Xie, Jianbo; Hong, Yuanyuan; Li, Pengfei; Chen, Sanfeng; Dixon, Ray; Li, Jilun

2013-01-01

Most biological nitrogen fixation is catalyzed by molybdenum-dependent nitrogenase, an enzyme complex comprising two component proteins that contains three different metalloclusters. Diazotrophs contain a common core of nitrogen fixation nif genes that encode the structural subunits of the enzyme and components required to synthesize the metalloclusters. However, the complement of nif genes required to enable diazotrophic growth varies significantly amongst nitrogen fixing bacteria and archaea. In this study, we identified a minimal nif gene cluster consisting of nine nif genes in the genome of Paenibacillus sp. WLY78, a gram-positive, facultative anaerobe isolated from the rhizosphere of bamboo. We demonstrate that the nif genes in this organism are organized as an operon comprising nifB, nifH, nifD, nifK, nifE, nifN, nifX, hesA and nifV and that the nif cluster is under the control of a σ70 (σA)-dependent promoter located upstream of nifB. To investigate genetic requirements for diazotrophy, we transferred the Paenibacillus nif cluster to Escherichia coli. The minimal nif gene cluster enables synthesis of catalytically active nitrogenase in this host, when expressed either from the native nifB promoter or from the T7 promoter. Deletion analysis indicates that in addition to the core nif genes, hesA plays an important role in nitrogen fixation and is responsive to the availability of molybdenum. Whereas nif transcription in Paenibacillus is regulated in response to nitrogen availability and by the external oxygen concentration, transcription from the nifB promoter is constitutive in E. coli, indicating that negative regulation of nif transcription is bypassed in the heterologous host. This study demonstrates the potential for engineering nitrogen fixation in a non-nitrogen fixing organism with a minimum set of nine nif genes. PMID:24146630

Is forced oscillation technique the next respiratory function test of choice in childhood asthma.

PubMed

Alblooshi, Afaf; Alkalbani, Alia; Albadi, Ghaya; Narchi, Hassib; Hall, Graham

2017-12-26

Respiratory diseases, especially asthma, are common in children. While spirometry contributes to asthma diagnosis and management in older children, it has a limited role in younger children whom are often unable to perform forced expiratory manoeuvre. The development of novel diagnostic methods which require minimal effort, such as forced oscillation technique (FOT) is, therefore, a welcome and promising addition. FOT involves applying external, small amplitude oscillations to the respiratory system during tidal breathing. Therefore, it requires minimal effort and cooperation. The FOT has the potential to facilitate asthma diagnosis and management in pre-school children by faciliting the objective measurement of baseline lung function and airway reactivity in children unable to successfully perform spirometry. Traditionally the use of FOT was limited to specialised centres. However, the availability of commercial equipment resulted in its use both in research and in clinical practice. In this article, we review the available literature on the use of FOT in childhood asthma. The technical aspects of FOT are described followed by a discussion of its practical aspects in the clinical field including the measurement of baseline lung function and associated reference ranges, bronchodilator responsiveness and bronchial hyper-responsiveness. We also highlight the difficulties and limitations that might be encountered and future research directions.

Advances in the Engineering of the Gene Editing Enzymes and the Genomes: Understanding and Handling the Off-Target Effects of CRISPR/Cas9.

PubMed

Yin, Yufang; Wang, Qian; Xiao, Li; Wang, Fengjiao; Song, Zhuo; Zhou, Cuilan; Liu, Xuan; Xing, Chungen; He, Nongyue; Li, Kai; Feng, Yan; Zhang, Jia

2018-03-01

In the past decades, significant progresses have been achieved in genetic engineering of nucleases. Among the genetically engineered nucleases, zinc finger nucleases, transcription activator-like (TAL) effector nucleases, and CRIPSPR/Cas9 system form a new field of gene editing. The gene editing efficiency or targeting effect and the off-target effect are the two major determinant factors in evaluating the usefulness of a new enzyme. Engineering strategies in improving these gene editing enzymes, particularly in minimizing their off-target effects, are the focus of this paper. Examples of using these genetically engineered enzymes in genome modification are discussed in order to better understand the requirement of engineering efforts in obtaining more powerful and useful gene editing enzymes. In addition, the identification of naturally existed anti-Cas proteins has been employed in minimizing off-target effects. Considering the future application in human gene therapy, optimization of these well recognized gene editing enzymes and exploration of more novel enzymes are both required. Before people find an ideal gene editing system having virtually no off-target effect, technologies used to screen and identify off-target effects are of importance in clinical trials employing gene therapy.

Longevity of major coenzymes allows minimal de novo synthesis in microorganisms.

PubMed

Hartl, Johannes; Kiefer, Patrick; Meyer, Fabian; Vorholt, Julia A

2017-05-15

Coenzymes are vital for cellular metabolism and act on the full spectrum of enzymatic reactions. Intrinsic chemical reactivity, enzyme promiscuity and high flux through their catalytic cycles make coenzymes prone to damage. To counteract such compromising factors and ensure stable levels of functional coenzymes, cells use a complex interplay between de novo synthesis, salvage, repair and degradation. However, the relative contribution of these factors is currently unknown, as is the overall stability of coenzymes in the cell. Here, we use dynamic 13 C-labelling experiments to determine the half-life of major coenzymes of Escherichia coli. We find that coenzymes such as pyridoxal 5-phosphate, flavins, nicotinamide adenine dinucleotide (phosphate) and coenzyme A are remarkably stable in vivo and allow biosynthesis close to the minimal necessary rate. In consequence, they are essentially produced to compensate for dilution by growth and passed on over generations of cells. Exceptions are antioxidants, which are short-lived, suggesting an inherent requirement for increased renewal. Although the growth-driven turnover of stable coenzymes is apparently subject to highly efficient end-product homeostasis, we exemplify that coenzyme pools are propagated in excess in relation to actual growth requirements. Additional testing of Bacillus subtilis and Saccharomyces cerevisiae suggests that coenzyme longevity is a conserved feature in biology.

Weighted-density functionals for cavity formation and dispersion energies in continuum solvation models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sundararaman, Ravishankar; Gunceler, Deniz; Arias, T. A.

2014-10-07

Continuum solvation models enable efficient first principles calculations of chemical reactions in solution, but require extensive parametrization and fitting for each solvent and class of solute systems. Here, we examine the assumptions of continuum solvation models in detail and replace empirical terms with physical models in order to construct a minimally-empirical solvation model. Specifically, we derive solvent radii from the nonlocal dielectric response of the solvent from ab initio calculations, construct a closed-form and parameter-free weighted-density approximation for the free energy of the cavity formation, and employ a pair-potential approximation for the dispersion energy. We show that the resulting modelmore » with a single solvent-independent parameter: the electron density threshold (n c), and a single solvent-dependent parameter: the dispersion scale factor (s 6), reproduces solvation energies of organic molecules in water, chloroform, and carbon tetrachloride with RMS errors of 1.1, 0.6 and 0.5 kcal/mol, respectively. We additionally show that fitting the solvent-dependent s 6 parameter to the solvation energy of a single non-polar molecule does not substantially increase these errors. Parametrization of this model for other solvents, therefore, requires minimal effort and is possible without extensive databases of experimental solvation free energies.« less

Weighted-density functionals for cavity formation and dispersion energies in continuum solvation models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sundararaman, Ravishankar; Gunceler, Deniz; Arias, T. A.

2014-10-07

Continuum solvation models enable efficient first principles calculations of chemical reactions in solution, but require extensive parametrization and fitting for each solvent and class of solute systems. Here, we examine the assumptions of continuum solvation models in detail and replace empirical terms with physical models in order to construct a minimally-empirical solvation model. Specifically, we derive solvent radii from the nonlocal dielectric response of the solvent from ab initio calculations, construct a closed-form and parameter-free weighted-density approximation for the free energy of the cavity formation, and employ a pair-potential approximation for the dispersion energy. We show that the resulting modelmore » with a single solvent-independent parameter: the electron density threshold (n{sub c}), and a single solvent-dependent parameter: the dispersion scale factor (s{sub 6}), reproduces solvation energies of organic molecules in water, chloroform, and carbon tetrachloride with RMS errors of 1.1, 0.6 and 0.5 kcal/mol, respectively. We additionally show that fitting the solvent-dependent s{sub 6} parameter to the solvation energy of a single non-polar molecule does not substantially increase these errors. Parametrization of this model for other solvents, therefore, requires minimal effort and is possible without extensive databases of experimental solvation free energies.« less

Minimizing or eliminating refueling of nuclear reactor

DOEpatents

Doncals, Richard A.; Paik, Nam-Chin; Andre, Sandra V.; Porter, Charles A.; Rathbun, Roy W.; Schwallie, Ambrose L.; Petras, Diane S.

1989-01-01

Demand for refueling of a liquid metal fast nuclear reactor having a life of 30 years is eliminated or reduced to intervals of at least 10 years by operating the reactor at a low linear-power density, typically 2.5 kw/ft of fuel rod, rather than 7.5 or 15 kw/ft, which is the prior art practice. So that power of the same magnitude as for prior art reactors is produced, the volume of the core is increased. In addition, the height of the core and it diameter are dimensioned so that the ratio of the height to the diameter approximates 1 to the extent practicable considering the requirement of control and that the pressure drop in the coolant shall not be excessive. The surface area of a cylinder of given volume is a minimum if the ratio of the height to the diameter is 1. By minimizing the surface area, the leakage of neutrons is reduced. By reducing the linear-power density, increasing core volume, reducing fissile enrichment and optimizing core geometry, internal-core breeding of fissionable fuel is substantially enhanced. As a result, core operational life, limited by control worth requirements and fuel burnup capability, is extended up to 30 years of continuous power operation.

Innovative technologies to manage aflatoxins in foods and feeds and the profitability of application - A review.

PubMed

Udomkun, Patchimaporn; Wiredu, Alexander Nimo; Nagle, Marcus; Müller, Joachim; Vanlauwe, Bernard; Bandyopadhyay, Ranajit

2017-06-01

Aflatoxins are mainly produced by certain strains of Aspergillus flavus , which are found in diverse agricultural crops. In many lower-income countries, aflatoxins pose serious public health issues since the occurrence of these toxins can be considerably common and even extreme. Aflatoxins can negatively affect health of livestock and poultry due to contaminated feeds. Additionally, they significantly limit the development of international trade as a result of strict regulation in high-value markets. Due to their high stability, aflatoxins are not only a problem during cropping, but also during storage, transport, processing, and handling steps. Consequently, innovative evidence-based technologies are urgently required to minimize aflatoxin exposure. Thus far, biological control has been developed as the most innovative potential technology of controlling aflatoxin contamination in crops, which uses competitive exclusion of toxigenic strains by non-toxigenic ones. This technology is commercially applied in groundnuts maize, cottonseed, and pistachios during pre-harvest stages. Some other effective technologies such as irradiation, ozone fumigation, chemical and biological control agents, and improved packaging materials can also minimize post-harvest aflatoxins contamination in agricultural products. However, integrated adoption of these pre- and post-harvest technologies is still required for sustainable solutions to reduce aflatoxins contamination, which enhances food security, alleviates malnutrition, and strengthens economic sustainability.

Evolution of an RNP assembly system: A minimal SMN complex facilitates formation of UsnRNPs in Drosophila melanogaster

PubMed Central

Kroiss, Matthias; Schultz, Jörg; Wiesner, Julia; Chari, Ashwin; Sickmann, Albert; Fischer, Utz

2008-01-01

In vertebrates, assembly of spliceosomal uridine-rich small nuclear ribonucleoproteins (UsnRNPs) is mediated by the SMN complex, a macromolecular entity composed of the proteins SMN and Gemins 2–8. Here we have studied the evolution of this machinery using complete genome assemblies of multiple model organisms. The SMN complex has gained complexity in evolution by a blockwise addition of Gemins onto an ancestral core complex composed of SMN and Gemin2. In contrast to this overall evolutionary trend to more complexity in metazoans, orthologs of most Gemins are missing in dipterans. In accordance with these bioinformatic data a previously undescribed biochemical purification strategy elucidated that the dipteran Drosophila melanogaster contains an SMN complex of remarkable simplicity. Surprisingly, this minimal complex not only mediates the assembly reaction in a manner very similar to its vertebrate counterpart, but also prevents misassembly onto nontarget RNAs. Our data suggest that only a minority of Gemins are required for the assembly reaction per se, whereas others may serve additional functions in the context of UsnRNP biogenesis. The evolution of the SMN complex is an interesting example of how the simplification of a biochemical process contributes to genome compaction. PMID:18621711

[Optimizing staff radiation protection in radiology by minimizing the effective dose].

PubMed

von Boetticher, H; Lachmund, J; Hoffmann, W; Luska, G

2006-03-01

In the present study the optimization of radiation protection devices is achieved by minimizing the effective dose of the staff members since the stochastic radiation effects correlate to the effective dose. Radiation exposure dosimetry was performed with TLD measurements using one Alderson Phantom in the patient position and a second phantom in the typical position of the personnel. Various types of protective clothing as well as fixed shields were considered in the calculations. It was shown that the doses of the unshielded organs (thyroid, parts of the active bone marrow) contribute significantly to the effective dose of the staff. Therefore, there is no linear relationship between the shielding factors for protective garments and the effective dose. An additional thyroid protection collar reduces the effective dose by a factor of 1.7 - 3.0. X-ray protective clothing with a 0.35 mm lead equivalent and an additional thyroid protection collar provides better protection against radiation than an apron with a 0.5 mm lead equivalent but no collar. The use of thyroid protection collars is an effective preventive measure against exceeding occupational organ dose limits, and a thyroid shield also considerably reduces the effective dose. Therefore, thyroid protection collars should be a required component of anti-X protection.

A UV-complete Composite Higgs model for Electroweak Symmetry Breaking: Minimal Conformal Technicolor

NASA Astrophysics Data System (ADS)

Tacchi, Ruggero Altair

The Large Hadron Collider is currently collecting data. One of the main goals of the experiment is to find evidence of the mechanism responsible for the breaking of the electroweak symmetry. There are many different models attempting to explain this breaking and traditionally most of them involve the use of supersymmetry near the scale of the breaking. This work is focused on exploring a viable model that is not based on a weakly coupled low scale supersymmetry sector to explain the electroweak symmetry breaking. We build a model based on a new strong interaction, in the fashion of theories commonly called "technicolor", name that is reminiscent of one of the first attempts of explaining the electroweak symmetry breaking using a strong interaction similar to the one whose charges are called colors. We explicitly study the minimal model of conformal technicolor, an SU(2) gauge theory near a strongly coupled conformal fixed point, with conformal symmetry softly broken by technifermion mass terms. Conformal symmetry breaking triggers chiral symmetry breaking in the pattern SU(4) → Sp (4), which gives rise to a pseudo-Nambu-Goldstone boson that can act as a composite Higgs boson. There is an additional composite pseudoscalar A with mass larger than mh and suppressed direct production at LHC. We discuss the electroweak fit in this model in detail. A good fit requires fine tuning at the 10% level. We construct a complete, realistic, and natural UV completion of the model, that explains the origin of quark and lepton masses and mixing angles. We embed conformal technicolor in a supersymmetric theory, with supersymmetry broken at a high scale. The effective theory below the supersymmetry breaking scale is minimal conformal technicolor with an additional light technicolor gaugino that might give rise to an additional pseudo Nambu-Goldstone boson that is observable at the LHC.

Efficient stage-specific differentiation of human pluripotent stem cells toward retinal photoreceptor cells.

PubMed

Mellough, Carla B; Sernagor, Evelyne; Moreno-Gimeno, Inmaculada; Steel, David H W; Lako, Majlinda

2012-04-01

Recent successes in the stem cell field have identified some of the key chemical and biological cues which drive photoreceptor derivation from human embryonic stem cells (hESC) and human induced pluripotent stem cells (hiPSC); however, the efficiency of this process is variable. We have designed a three-step photoreceptor differentiation protocol combining previously published methods that direct the differentiation of hESC and hiPSC toward a retinal lineage, which we further modified with additional supplements selected on the basis of reports from the eye field and retinal development. We report that hESC and hiPSC differentiating under our regimen over a 60 day period sequentially acquire markers associated with neural, retinal field, retinal pigmented epithelium and photoreceptor cells, including mature photoreceptor markers OPN1SW and RHODOPSIN with a higher efficiency than previously reported. In addition, we report the ability of hESC and hiPSC cultures to generate neural and retinal phenotypes under minimal culture conditions, which may be linked to their ability to endogenously upregulate the expression of a range of factors important for retinal cell type specification. However, cultures that were differentiated with full supplementation under our photoreceptor-induction regimen achieve this within a significantly shorter time frame and show a substantial increase in the expression of photoreceptor-specific markers in comparison to cultures differentiated under minimal conditions. Interestingly, cultures supplemented only with B27 and/or N2 displayed comparable differentiation efficiency to those under full supplementation, indicating a key role for B27 and N2 during the differentiation process. Furthermore, our data highlight an important role for Dkk1 and Noggin in enhancing the differentiation of hESC and hiPSC toward retinal progenitor cells and photoreceptor precursors during the early stages of differentiation, while suggesting that further maturation of these cells into photoreceptors may not require additional factors and can ensue under minimal culture conditions. Copyright © 2012 AlphaMed Press.

Impact of glucose and acetate on the characteristics of the platelet storage lesion in platelets suspended in additive solutions with minimal plasma.

PubMed

Saunders, C; Rowe, G; Wilkins, K; Collins, P

2013-07-01

Glucose and acetate have been proposed to be required elements in platelet storage media. This study investigated the role of these compounds on the varied elements that comprise the platelet storage lesion. For each replicate, four pooled and split ABO group-specific buffy coat-derived platelet concentrates were suspended in an in-house additive solution with minimal plasma and varying final concentrations of acetate or glucose. Units were sampled on days 2, 3, 6, 8 and 10 and tested for markers of platelet morphology, activation, function, metabolism and indicators of cell death. The absence of glucose was associated with a decrease in ATP, falling to a mean of 1·1 ± 0·1 μmol/10(11) plts in units with no added glucose compared with 4·2 ± 0·6 μmol/10(11) plts (P < 0·001) in units with 30 mm glucose. As glucose became depleted, the decrease in ATP to levels below 3 μmol/10(11) plts was associated with an increase in both annexin V binding and intracellular free calcium. In units lacking exogenous acetate, ATP levels on day 10 were 5·2 ± 1·5 μmol/10(11) plts compared with 2·7 ± 0·9 μmol/10(11) plts in units with 56 mm acetate (P = 0·006). Higher concentrations of exogenous acetate were associated with a lower hypotonic shock response and higher surface expression of CD62P suggestive of a dose dependency. Under current physical storage conditions, glucose appears necessary for the maintenance of platelets stored as concentrates in minimal volumes of plasma. The addition of acetate was associated with increased platelet activation and reduced ATP levels. © 2013 International Society of Blood Transfusion.

Simulation Evaluation of Pilot Inputs for Real Time Modeling During Commercial Flight Operations

NASA Technical Reports Server (NTRS)

Martos, Borja; Ranaudo, Richard; Oltman, Ryan; Myhre, Nick

2017-01-01

Aircraft dynamics characteristics can only be identified from flight data when the aircraft dynamics are excited sufficiently. A preliminary study was conducted into what types and levels of manual piloted control excitation would be required for accurate Real-Time Parameter IDentification (RTPID) results by commercial airline pilots. This includes assessing the practicality for the pilot to provide this excitation when cued, and to further understand if pilot inputs during various phases of flight provide sufficient excitation naturally. An operationally representative task was evaluated by 5 commercial airline pilots using the NASA Ice Contamination Effects Flight Training Device (ICEFTD). Results showed that it is practical to use manual pilot inputs only as a means of achieving good RTPID in all phases of flight and in flight turbulence conditions. All pilots were effective in satisfying excitation requirements when cued. Much of the time, cueing was not even necessary, as just performing the required task provided enough excitation for accurate RTPID estimation. Pilot opinion surveys reported that the additional control inputs required when prompted by the excitation cueing were easy to make, quickly mastered, and required minimal training.

Starshade orbital maneuver study for WFIRST

NASA Astrophysics Data System (ADS)

Soto, Gabriel; Sinha, Amlan; Savransky, Dmitry; Delacroix, Christian; Garrett, Daniel

2017-09-01

The Wide Field Infrared Survey Telescope (WFIRST) mission, scheduled for launch in the mid-2020s will perform exoplanet science via both direct imaging and a microlensing survey. An internal coronagraph is planned to perform starlight suppression for exoplanet imaging, but an external starshade could be used to achieve the required high contrasts with potentially higher throughput. This approach would require a separately-launched occulter spacecraft to be positioned at exact distances from the telescope along the line of sight to a target star system. We present a detailed study to quantify the Δv requirements and feasibility of deploying this additional spacecraft as a means of exoplanet imaging. The primary focus of this study is the fuel use of the occulter while repositioning between targets. Based on its design, the occulter is given an offset distance from the nominal WFIRST halo orbit. Target star systems and look vectors are generated using Exoplanet Open-Source Imaging Simulator (EXOSIMS); a boundary value problem is then solved between successive targets. On average, 50 observations are achievable with randomly selected targets given a 30-day transfer time. Individual trajectories can be optimized for transfer time as well as fuel usage to be used in mission scheduling. Minimizing transfer time reduces the total mission time by up to 4.5 times in some simulations before expending the entire fuel budget. Minimizing Δv can generate starshade missions that achieve over 100 unique observations within the designated mission lifetime of WFIRST.

The role of elastic energy in activities with high force and power requirements: a brief review.

PubMed

Wilson, Jacob M; Flanagan, Eamonn P

2008-09-01

The purpose of this article is to provide strength and conditioning practitioners with an understanding of the role of elastic energy in activities with high force and power requirements. Specifically, the article covers 1) the nature of elasticity and its application to human participants, 2) the role of elastic energy in activities requiring a stretch-shorten cycle such as the vertical jump, 3) the role of muscular stiffness in athletic performance, 4) the control of muscular stiffness through feedforward and feedback mechanisms, and 5) factors affecting muscular stiffness. Finally, practical applications are provided. In this section, it is suggested that the storage and reuse of elastic energy is optimized at relatively higher levels of stiffness. Because stiffness decreases as fatigue ensues as well as with stretching before an event, the article emphasizes the need for proper preparation phases in a periodized cycle and the avoidance of long static stretches before high-force activities. The importance of teaching athletes to transition from eccentric to concentric movements with minimal time delays is also proposed due to the finding that time delays appear to decrease the reuse of elastic energy. In addition to teaching within the criterion tasks, evidence is provided that minimizing transitions in plyometric training, a technique demonstrated to increase musculotendinous stiffness, can optimize power output in explosive movements. Finally, evidence is provided that training and teaching programs designed to optimize muscular stiffness may protect athletes against sports-related injuries.

New minimally access hydrocelectomy.

PubMed

Saber, Aly

2011-02-01

To ascertain the acceptability of minimally access hydrocelectomy through a 2-cm incision and the outcome in terms of morbidity reduction and recurrence rate. Although controversy exists regarding the treatment of hydrocele, hydrocelectomy remains the treatment of choice for hydroceles. However, the standard surgical procedures for hydrocele can cause postoperative discomfort and complications. A total of 42 adult patients, aged 18-56 years, underwent hydrocelectomy as an outpatient procedure using a 2-cm scrotal skin incision and excision of only a small disk of the parietal tunica vaginalis. The operative time was 12-18 minutes (mean 15). The outcome measures included patient satisfaction and postoperative complications. This procedure requires minor dissection and minimal manipulation during treatment. It also resulted in no recurrence and minimal complications and required a short operative time. Copyright © 2011 Elsevier Inc. All rights reserved.

A novel remote center of motion mechanism for the force-reflective master robot of haptic tele-surgery systems.

PubMed

Hadavand, Mostafa; Mirbagheri, Alireza; Behzadipour, Saeed; Farahmand, Farzam

2014-06-01

An effective master robot for haptic tele-surgery applications needs to provide a solution for the inversed movements of the surgical tool, in addition to sufficient workspace and manipulability, with minimal moving inertia. A novel 4 + 1-DOF mechanism was proposed, based on a triple parallelogram linkage, which provided a Remote Center of Motion (RCM) at the back of the user's hand. The kinematics of the robot was analyzed and a prototype was fabricated and evaluated by experimental tests. With a RCM at the back of the user's hand the actuators far from the end effector, the robot could produce the sensation of hand-inside surgery with minimal moving inertia. The target workspace was achieved with an acceptable manipulability. The trajectory tracking experiments revealed small errors, due to backlash at the joints. The proposed mechanism meets the basic requirements of an effective master robot for haptic tele-surgery applications. Copyright © 2013 John Wiley & Sons, Ltd.

An Optimal Current Observer for Predictive Current Controlled Buck DC-DC Converters

PubMed Central

Min, Run; Chen, Chen; Zhang, Xiaodong; Zou, Xuecheng; Tong, Qiaoling; Zhang, Qiao

2014-01-01

In digital current mode controlled DC-DC converters, conventional current sensors might not provide isolation at a minimized price, power loss and size. Therefore, a current observer which can be realized based on the digital circuit itself, is a possible substitute. However, the observed current may diverge due to the parasitic resistors and the forward conduction voltage of the diode. Moreover, the divergence of the observed current will cause steady state errors in the output voltage. In this paper, an optimal current observer is proposed. It achieves the highest observation accuracy by compensating for all the known parasitic parameters. By employing the optimal current observer-based predictive current controller, a buck converter is implemented. The converter has a convergently and accurately observed inductor current, and shows preferable transient response than the conventional voltage mode controlled converter. Besides, costs, power loss and size are minimized since the strategy requires no additional hardware for current sensing. The effectiveness of the proposed optimal current observer is demonstrated experimentally. PMID:24854061

Two-dimensional frequency-domain acoustic full-waveform inversion with rugged topography

NASA Astrophysics Data System (ADS)

Zhang, Qian-Jiang; Dai, Shi-Kun; Chen, Long-Wei; Li, Kun; Zhao, Dong-Dong; Huang, Xing-Xing

2015-09-01

We studied finite-element-method-based two-dimensional frequency-domain acoustic FWI under rugged topography conditions. The exponential attenuation boundary condition suitable for rugged topography is proposed to solve the cutoff boundary problem as well as to consider the requirement of using the same subdivision grid in joint multifrequency inversion. The proposed method introduces the attenuation factor, and by adjusting it, acoustic waves are sufficiently attenuated in the attenuation layer to minimize the cutoff boundary effect. Based on the law of exponential attenuation, expressions for computing the attenuation factor and the thickness of attenuation layers are derived for different frequencies. In multifrequency-domain FWI, the conjugate gradient method is used to solve equations in the Gauss-Newton algorithm and thus minimize the computation cost in calculating the Hessian matrix. In addition, the effect of initial model selection and frequency combination on FWI is analyzed. Examples using numerical simulations and FWI calculations are used to verify the efficiency of the proposed method.

Process for gasifying carbonaceous material from a recycled condensate slurry

DOEpatents

Forney, Albert J.; Haynes, William P.

1981-01-01

Coal or other carbonaceous material is gasified by reaction with steam and oxygen in a manner to minimize the problems of effluent water stream disposal. The condensate water from the product gas is recycled to slurry the coal feed and the amount of additional water or steam added for cooling or heating is minimized and preferably kept to a level of about that required to react with the carbonaceous material in the gasification reaction. The gasification is performed in a pressurized fluidized bed with the coal fed in a water slurry and preheated or vaporized by indirect heat exchange contact with product gas and recycled steam. The carbonaceous material is conveyed in a gas-solid mixture from bottom to top of the pressurized fluidized bed gasifier with the solids removed from the product gas and recycled steam in a supported moving bed filter of the resulting carbonaceous char. Steam is condensed from the product gas and the condensate recycled to form a slurry with the feed coal carbonaceous particles.

Considerations for Architecture Level Trade Studies for Environmental Sensors

NASA Technical Reports Server (NTRS)

Peterson, Craig

2010-01-01

Comparisons of key characteristics of environmental sensors such as technology readiness levels, mass, power, volume, and detection capabilities are essential for initial trade studies to determine likely candidates for further development and evaluation. However, these trade studies only provide part of the information necessary to make selection decisions. Ultimately, the sensors must be judged based on the overall system architectures and operational scenarios for which they are intended. This means that additional characteristics, such as architectural needs for redundancy, operational lifetime, ability to maintain calibration, and repair and replacement strategies, among others, must also be considered. Given that these characteristics can be extremely time-consuming and costly to obtain, careful planning is essential to minimize the effort involved. In this paper, an approach is explored for determining an effective yet comprehensive set of architecture level trades which is minimally impacted by the inevitable changes in operational (mission) scenarios. The approach will also identify and integrate the various facilities and opportunities required to obtain the desired architecture level trade information.

Minimal mirror twin Higgs

DOE PAGES

Barbieri, Riccardo; Hall, Lawrence J.; Harigaya, Keisuke

2016-11-29

In a Mirror Twin World with a maximally symmetric Higgs sector the little hierarchy of the Standard Model can be significantly mitigated, perhaps displacing the cutoff scale above the LHC reach. We show that consistency with observations requires that the Z 2 parity exchanging the Standard Model with its mirror be broken in the Yukawa couplings. A minimal such effective field theory, with this sole Z 2 breaking, can generate the Z 2 breaking in the Higgs sector necessary for the Twin Higgs mechanism. The theory has constrained and correlated signals i n Higgs decays, direct Dark Matter Detection andmore » Dark Radiation, all within reach of foreseen experiments, over a region of parameter space where the fine-tuning for the electroweak scale is 10-50%. For dark matter, both mirror neutrons and a variety of self-interacting mirror atoms are considered. Neutrino mass signals and the effects of a possible additional Z 2 breaking from the vacuum expectation values of B-L breaking fields are also discussed.« less

Instrument Package Manipulation Through the Generation and Use of an Attenuated-Fluent Gas Fold

NASA Technical Reports Server (NTRS)

Breen, Daniel P.

2012-01-01

This document discusses a technique that provides a means for suspending large, awkward loads, instrument packages, components, and machinery in a stable, controlled, and precise manner. In the baseplate of the test machine, a pattern of grooves and ports is installed that when pressurized generates an attenuated- fluent gas fold providing a low-cost, near-zero-coefficient-of-friction lubrication boundary layer that supports the object evenly, and in a predictable manner. Package movement control requires minimal force. Aids to repeatable travel and positional accuracy can be added via the addition of simple guide bars and stops to the floor or object being moved. This allows easily regulated three-axis motions. Loads of extreme weight and size can be moved and guided by a single person, or by automated means, using minimal force. Upon removal of the attenuated fluent gas fold, the object returns to a stable resting position without impact forces affecting the object.

USER'S GUIDE: Strategic Waste Minimization Initiative (SWAMI) Version 2.0 - A Software Tool to Aid in Process Analysis for Pollution Prevention

EPA Science Inventory

The Strategic WAste Minimization Initiative (SWAMI) Software, Version 2.0 is a tool for using process analysis for identifying waste minimization opportunities within an industrial setting. The software requires user-supplied information for process definition, as well as materia...

Low-Friction, High-Stiffness Joint for Uniaxial Load Cell

NASA Technical Reports Server (NTRS)

Lewis, James L.; Le, Thang; Carroll, Monty B.

2007-01-01

A universal-joint assembly has been devised for transferring axial tension or compression to a load cell. To maximize measurement accuracy, the assembly is required to minimize any moments and non-axial forces on the load cell and to exhibit little or no hysteresis. The requirement to minimize hysteresis translates to a requirement to maximize axial stiffness (including minimizing backlash) and a simultaneous requirement to minimize friction. In practice, these are competing requirements, encountered repeatedly in efforts to design universal joints. Often, universal-joint designs represent compromises between these requirements. The improved universal-joint assembly contains two universal joints, each containing two adjustable pairs of angular-contact ball bearings. One might be tempted to ask why one could not use simple ball-and-socket joints rather than something as complex as universal joints containing adjustable pairs of angularcontact ball bearings. The answer is that ball-and-socket joints do not offer sufficient latitude to trade stiffness versus friction: the inevitable result of an attempt to make such a trade in a ball-and-socket joint is either too much backlash or too much friction. The universal joints are located at opposite ends of an axial subassembly that contains the load cell. The axial subassembly includes an axial shaft, an axial housing, and a fifth adjustable pair of angular-contact ball bearings that allows rotation of the axial housing relative to the shaft. The preload on each pair of angular-contact ball bearings can be adjusted to obtain the required stiffness with minimal friction, tailored for a specific application. The universal joint at each end affords two degrees of freedom, allowing only axial force to reach the load cell regardless of application of moments and non-axial forces. The rotational joint on the axial subassembly affords a fifth degree of freedom, preventing application of a torsion load to the load cell.

Thermodynamics of computation and information distance

NASA Astrophysics Data System (ADS)

Bennett, Charles H.; Gacs, Peter; Li, Ming; Vitanyi, Paul M. R. B.; Zurek, Wojciech H.

1993-06-01

Intuitively, the minimal information distance between x and y is the length of the shortest program for a universal computer to transform x into y and y into x. This measure is shown to be, up to a logarithmic additive term, equal to the maximum of the conditional Kolmogorov complexities E(sub 1)(x,y) = max(K(y/x), K(x/y)). Any reasonable distance to measure similarity of pictures should be an effectively approximable, symmetric, positive function of x and y satisfying a reasonable normalization condition and obeying the triangle inequality. It turns out that E(sub 1) is minimal up to an additive constant among all such distances. Hence it is a universal 'picture distance', which accounts for any effective similarity between pictures. A third information distance, based on the ideal that the aim should be for dissipationless computations, and hence for reversible ones, is given by the length E(sub 2)(x,y) = KR(y/x) = KR(x/y) of the shortest reversible program that transforms x into y and y into x on a universal reversible computer. It is shown that also E(sub 2) = E(sub 1), up to a logarithmic additive term. It is remarkable that three so differently motivated definitions turn out to define one and the same notion. Another information distance, E(sub 3), is obtained by minimizing the total amount of information flowing in and out during a reversible computation in which the program is not retained, in other words the number of extra bits (apart from x) that must be irreversibly supplied at the beginning, plus the number of garbage bits (apart from y) that must be irreversibly erased at the end of the computation to obtain a 'clean' y. This distance is within a logarithmic additive term of the sum of the conditional complexities, E(sub 3)(x, y) = K(y/x) + K(x/y). Using the physical theory of reversible computation, the simple difference K(x) - K(y) is shown to be an appropriate (universal, antisymmetric, and transitive) measure of the amount of thermodynamic work required to transform string x into string y by the most efficient process.

On eco-efficient technologies to minimize industrial water consumption

NASA Astrophysics Data System (ADS)

Amiri, Mohammad C.; Mohammadifard, Hossein; Ghaffari, Ghasem

2016-07-01

Purpose - Water scarcity will further stress on available water systems and decrease the security of water in many areas. Therefore, innovative methods to minimize industrial water usage and waste production are of paramount importance in the process of extending fresh water resources and happen to be the main life support systems in many arid regions of the world. This paper demonstrates that there are good opportunities for many industries to save water and decrease waste water in softening process by substituting traditional with echo-friendly methods. The patented puffing method is an eco-efficient and viable technology for water saving and waste reduction in lime softening process. Design/methodology/approach - Lime softening process (LSP) is a very sensitive process to chemical reactions. In addition, optimal monitoring not only results in minimizing sludge that must be disposed of but also it reduces the operating costs of water conditioning. Weakness of the current (regular) control of LSP based on chemical analysis has been demonstrated experimentally and compared with the eco-efficient puffing method. Findings - This paper demonstrates that there is a good opportunity for many industries to save water and decrease waste water in softening process by substituting traditional method with puffing method, a patented eco-efficient technology. Originality/value - Details of the required innovative works to minimize industrial water usage and waste production are outlined in this paper. Employing the novel puffing method for monitoring of lime softening process results in saving a considerable amount of water while reducing chemical sludge.

Performance of basic kinematic thresholds in the identification of crash and near-crash events within naturalistic driving data.

PubMed

Perez, Miguel A; Sudweeks, Jeremy D; Sears, Edie; Antin, Jonathan; Lee, Suzanne; Hankey, Jonathan M; Dingus, Thomas A

2017-06-01

Understanding causal factors for traffic safety-critical events (e.g., crashes and near-crashes) is an important step in reducing their frequency and severity. Naturalistic driving data offers unparalleled insight into these factors, but requires identification of situations where crashes are present within large volumes of data. Sensitivity and specificity of these identification approaches are key to minimizing the resources required to validate candidate crash events. This investigation used data from the Second Strategic Highway Research Program Naturalistic Driving Study (SHRP 2 NDS) and the Canada Naturalistic Driving Study (CNDS) to develop and validate different kinematic thresholds that can be used to detect crash events. Results indicate that the sensitivity of many of these approaches can be quite low, but can be improved by selecting particular threshold levels based on detection performance. Additional improvements in these approaches are possible, and may involve leveraging combinations of different detection approaches, including advanced statistical techniques and artificial intelligence approaches, additional parameter modifications, and automation of validation processes. Copyright © 2017 Elsevier Ltd. All rights reserved.

Hybrid Propulsion In-Situ Resource Utilization Test Facility Results

NASA Technical Reports Server (NTRS)

Karp, Ashley Chandler; Nakazono, Barry; Vaughan, David; Warner, William N.

2015-01-01

Hybrid rockets present a promising alternative to conventional chemical propulsion systems for In-Situ Resource Utilization (ISRU) and in-space applications. While they have many benefits for these applications, there are still many small details that require research before they can be adopted into flight systems. A flexible test facility was developed at JPL to test operation of hybrid motors at small scale (5 cm outer diameter fuel grains) over a range of conditions. Specifically, this paper studies two of the major advantages: low temperature performance and throttling. Paraffin-based hybrid rockets are predicted to have good performance at low temperatures. This could significantly decrease the overall system mass by minimizing the thermal conditioning required for Mars or outer planet applications. Therefore, the coefficient of thermal expansion and glass transition of paraffin are discussed. Additionally, deep throttling has been considered for several applications. This was a natural starting point for hotfire testing using the hybrid propulsion ISRU test facility. Additionally, short length to diameter ratio (L/D) fuel grains are tested to determine if these systems can be packaged into geometrically constrained spaces.

Active Yeast Telomerase Shares Subunits with Ribonucleoproteins RNase P and RNase MRP.

PubMed

Lemieux, Bruno; Laterreur, Nancy; Perederina, Anna; Noël, Jean-François; Dubois, Marie-Line; Krasilnikov, Andrey S; Wellinger, Raymund J

2016-05-19

Telomerase is the ribonucleoprotein enzyme that replenishes telomeric DNA and maintains genome integrity. Minimally, telomerase activity requires a templating RNA and a catalytic protein. Additional proteins are required for activity on telomeres in vivo. Here, we report that the Pop1, Pop6, and Pop7 proteins, known components of RNase P and RNase MRP, bind to yeast telomerase RNA and are essential constituents of the telomerase holoenzyme. Pop1/Pop6/Pop7 binding is specific and involves an RNA domain highly similar to a protein-binding domain in the RNAs of RNase P/MRP. The results also show that Pop1/Pop6/Pop7 function to maintain the essential components Est1 and Est2 on the RNA in vivo. Consistently, addition of Pop1 allows for telomerase activity reconstitution with wild-type telomerase RNA in vitro. Thus, the same chaperoning module has allowed the evolution of functionally and, remarkably, structurally distinct RNPs, telomerase, and RNases P/MRP from unrelated progenitor RNAs. Copyright © 2016 Elsevier Inc. All rights reserved.

Fibre optic portable rail vehicle detector

NASA Astrophysics Data System (ADS)

Kepak, Stanislav; Cubik, Jakub; Zavodny, Petr; Hejduk, Stanislav; Nedoma, Jan; Davidson, Alan; Vasinek, Vladimir

2016-12-01

During track maintenance operations, the early detection of oncoming rail vehicles is critical for the safety of maintenance personnel. In addition, the detection system should be simple to install at the trackside by minimally qualified personnel. Fibre optic based sensor systems have the inherent advantages of being passive, unaffected by radio frequency interference (RFI) and suffering very low signal attenuation. Such a system therefore represents a good alternative to conventional approaches such as ultrasonic based sensor systems. The proposed system consists of one or more passive fibre trackside sensors and an x86 processing unit located at the work site. The solid fibre connection between sensors and processing unit eliminates the risk of RFI. In addition, the detection system sensors are easy to install with no requirement for electrical power at the sensor site. The system was tested on a tram line in Ostrava with the results obtained indicating the successful detection of all the trams in the monitoring windows using a single sensor. However, the platform allows flexibility in configuring multiple sensors where required by system users.

Designing Delta-DOR acquisition strategies to determine highly elliptical earth orbits

NASA Technical Reports Server (NTRS)

Frauenholz, R. B.

1986-01-01

Delta-DOR acquisition strategies are designed for use in determining highly elliptical earth orbits. The requirements for a possible flight demonstration are evaluated for the Charged Composition Explorer spacecraft of the Active Magnetospheric Particle Tracer Explorers. The best-performing strategy uses data spanning the view periods of two orthogonal baselines near the same orbit periapse. The rapidly changing viewing geometry yields both angular position and velocity information, but each observation may require a different reference quasar. The Delta-DOR data noise is highly dependent on acquisition geometry, varying several orders of magnitude across the baseline view periods. Strategies are selected to minimize the measurement noise predicted by a theoretical model. Although the CCE transponder is limited by S-band and a small bandwidth, the addition of Delta-DOR to coherent Doppler and range improves the one-sigma apogee position accuracy by more than an order of magnitude. Additional Delta-DOR accuracy improvements possible using dual-frequency (S/X) calibration, increased spanned bandwidth, and water-vapor radiometry are presented for comparison. With these benefits, the residual Delta-DOR data noise is primarily due to quasar position uncertainties.

Combining Genome-Scale Experimental and Computational Methods To Identify Essential Genes in Rhodobacter sphaeroides

DOE PAGES

Burger, Brian T.; Imam, Saheed; Scarborough, Matthew J.; ...

2017-06-06

Rhodobacter sphaeroides is one of the best-studied alphaproteobacteria from biochemical, genetic, and genomic perspectives. To gain a better systems-level understanding of this organism, we generated a large transposon mutant library and used transposon sequencing (Tn-seq) to identify genes that are essential under several growth conditions. Using newly developed Tn-seq analysis software (TSAS), we identified 493 genes as essential for aerobic growth on a rich medium. We then used the mutant library to identify conditionally essential genes under two laboratory growth conditions, identifying 85 additional genes required for aerobic growth in a minimal medium and 31 additional genes required for photosyntheticmore » growth. In all instances, our analyses confirmed essentiality for many known genes and identified genes not previously considered to be essential. We used the resulting Tn-seq data to refine and improve a genome-scale metabolic network model (GEM) for R. sphaeroides. Together, we demonstrate how genetic, genomic, and computational approaches can be combined to obtain a systems-level understanding of the genetic framework underlying metabolic diversity in bacterial species.« less

[Minimally invasive coronary artery surgery].

PubMed

Zalaquett, R; Howard, M; Irarrázaval, M J; Morán, S; Maturana, G; Becker, P; Medel, J; Sacco, C; Lema, G; Canessa, R; Cruz, F

1999-01-01

There is a growing interest to perform a left internal mammary artery (LIMA) graft to the left anterior descending coronary artery (LAD) on a beating heart through a minimally invasive access to the chest cavity. To report the experience with minimally invasive coronary artery surgery. Analysis of 11 patients aged 48 to 79 years old with single vessel disease that, between 1996 and 1997, had a LIMA graft to the LAD performed through a minimally invasive left anterior mediastinotomy, without cardiopulmonary bypass. A 6 to 10 cm left parasternal incision was done. The LIMA to the LAD anastomosis was done after pharmacological heart rate and blood pressure control and a period of ischemic pre conditioning. Graft patency was confirmed intraoperatively by standard Doppler techniques. Patients were followed for a mean of 11.6 months (7-15 months). All patients were extubated in the operating room and transferred out of the intensive care unit on the next morning. Seven patients were discharged on the third postoperative day. Duplex scanning confirmed graft patency in all patients before discharge; in two patients, it was confirmed additionally by arteriography. There was no hospital mortality, no perioperative myocardial infarction and no bleeding problems. After follow up, ten patients were free of angina, in functional class I and pleased with the surgical and cosmetic results. One patient developed atypical angina on the seventh postoperative month and a selective arteriography confirmed stenosis of the anastomosis. A successful angioplasty of the original LAD lesion was carried out. A minimally invasive left anterior mediastinotomy is a good surgical access to perform a successful LIMA to LAD graft without cardiopulmonary bypass, allowing a shorter hospital stay and earlier postoperative recovery. However, a larger experience and a longer follow up is required to define its role in the treatment of coronary artery disease.

Subject-specific cardiovascular system model-based identification and diagnosis of septic shock with a minimally invasive data set: animal experiments and proof of concept.

PubMed

Chase, J Geoffrey; Lambermont, Bernard; Starfinger, Christina; Hann, Christopher E; Shaw, Geoffrey M; Ghuysen, Alexandre; Kolh, Philippe; Dauby, Pierre C; Desaive, Thomas

2011-01-01

A cardiovascular system (CVS) model and parameter identification method have previously been validated for identifying different cardiac and circulatory dysfunctions in simulation and using porcine models of pulmonary embolism, hypovolemia with PEEP titrations and induced endotoxic shock. However, these studies required both left and right heart catheters to collect the data required for subject-specific monitoring and diagnosis-a maximally invasive data set in a critical care setting although it does occur in practice. Hence, use of this model-based diagnostic would require significant additional invasive sensors for some subjects, which is unacceptable in some, if not all, cases. The main goal of this study is to prove the concept of using only measurements from one side of the heart (right) in a 'minimal' data set to identify an effective patient-specific model that can capture key clinical trends in endotoxic shock. This research extends existing methods to a reduced and minimal data set requiring only a single catheter and reducing the risk of infection and other complications-a very common, typical situation in critical care patients, particularly after cardiac surgery. The extended methods and assumptions that found it are developed and presented in a case study for the patient-specific parameter identification of pig-specific parameters in an animal model of induced endotoxic shock. This case study is used to define the impact of this minimal data set on the quality and accuracy of the model application for monitoring, detecting and diagnosing septic shock. Six anesthetized healthy pigs weighing 20-30 kg received a 0.5 mg kg(-1) endotoxin infusion over a period of 30 min from T0 to T30. For this research, only right heart measurements were obtained. Errors for the identified model are within 8% when the model is identified from data, re-simulated and then compared to the experimentally measured data, including measurements not used in the identification process for validation. Importantly, all identified parameter trends match physiologically and clinically and experimentally expected changes, indicating that no diagnostic power is lost. This work represents a further with human subjects validation for this model-based approach to cardiovascular diagnosis and therapy guidance in monitoring endotoxic disease states. The results and methods obtained can be readily extended from this case study to the other animal model results presented previously. Overall, these results provide further support for prospective, proof of concept clinical testing with humans.

Cash Management in the United States Marine Corps.

DTIC Science & Technology

1984-12-01

procedures and requires that such departments and agencies conduct financial * activities in a manner that will make cash holding require- ments...balances so as to minimize the overall cost of holding cash" [Ref. 3: 2). Simply stated, effective cash management implies the minimization of cash...balances held, as opposed to invested , as well as timely receipt and disbursement of government funds. B. ORGANIZATION RESPONSIBILITY FOR FINANCIAL

Examining the Minimal Required Elements of a Computer-Tailored Intervention Aimed at Dietary Fat Reduction: Results of a Randomized Controlled Dismantling Study

ERIC Educational Resources Information Center

Kroeze, Willemieke; Oenema, Anke; Dagnelie, Pieter C.; Brug, Johannes

2008-01-01

This study investigated the minimally required feedback elements of a computer-tailored dietary fat reduction intervention to be effective in improving fat intake. In all 588 Healthy Dutch adults were randomly allocated to one of four conditions in an randomized controlled trial: (i) feedback on dietary fat intake [personal feedback (P feedback)],…

In-Space Recycler Technology Demonstration

NASA Technical Reports Server (NTRS)

Hoyt, Rob; Werkheiser, NIKI; Kim, Tony

2016-01-01

In 2014, a 3D printer was installed and used successfully on the International Space Station (ISS), creating the first additively manufactured part in space. While additive manufacturing is a game changing technology for exploration missions, the process still requires raw feedstock material to fabricate parts. Without a recycling capability, a large supply of feedstock would need to be stored onboard, which negates the logistical benefits of these capabilities. Tethers Unlimited, Inc. (TUI), received a Small Business Innovation Research (SBIR) award to design and build the first In-space Recycler for demonstration aboard the ISS in 2017. To fully test this technology in microgravity, parts will be 3D printed, recycled into reusable filament, and then reprinted into new parts. Recycling scrap into printer filament is quite challenging in that a recycler must be able to handle a large variety of possible scrap configurations and densities. New challenges include: dealing with inevitable contamination of the scrap material, minimizing damage to the molecular structure of the plastic during reprocessing, managing a larger volume of hot liquid plastic, and exercising greater control over the cooling/resolidification of the material. TUI has developed an architecture that addresses these challenges by combining standard, proven technologies with novel, patented processes developed through this effort. Results show that the filament diameter achieved is more consistent than commercial filament, with only minimal degradation of material properties over recycling steps. In May 2016, TUI completed fabrication of a flight prototype, which will ultimately progress to the demonstration unit for the ISS as a testbed for future exploration missions. This capability will provide significant cost savings by reducing the launch mass and volume required for printer feedstock as well as reduce waste that must be stored or disposed.

Energy-Efficient ZigBee-Based Wireless Sensor Network for Track Bicycle Performance Monitoring

PubMed Central

Gharghan, Sadik K.; Nordin, Rosdiadee; Ismail, Mahamod

2014-01-01

In a wireless sensor network (WSN), saving power is a vital requirement. In this paper, a simple point-to-point bike WSN was considered. The data of bike parameters, speed and cadence, were monitored and transmitted via a wireless communication based on the ZigBee protocol. Since the bike parameters are monitored and transmitted on every bike wheel rotation, this means the sensor node does not sleep for a long time, causing power consumption to rise. Therefore, a newly proposed algorithm, known as the Redundancy and Converged Data (RCD) algorithm, was implemented for this application to put the sensor node into sleep mode while maintaining the performance measurements. This is achieved by minimizing the data packets transmitted as much as possible and fusing the data of speed and cadence by utilizing the correlation measurements between them to minimize the number of sensor nodes in the network to one node, which results in reduced power consumption, cost, and size, in addition to simpler hardware implementation. Execution of the proposed RCD algorithm shows that this approach can reduce the current consumption to 1.69 mA, and save 95% of the sensor node energy. Also, the comparison results with different wireless standard technologies demonstrate minimal current consumption in the sensor node. PMID:25153141

Modeling elasto-viscoplasticity in a consistent phase field framework

DOE PAGES

Cheng, Tian -Le; Wen, You -Hai; Hawk, Jeffrey A.

2017-05-19

Existing continuum level phase field plasticity theories seek to solve plastic strain by minimizing the shear strain energy. However, rigorously speaking, for thermodynamic consistency it is required to minimize the total strain energy unless there is proof that hydrostatic strain energy is independent of plastic strain which is unfortunately absent. In this work, we extend the phase-field microelasticity theory of Khachaturyan et al. by minimizing the total elastic energy with constraint of incompressibility of plastic strain. We show that the flow rules derived from the Ginzburg-Landau type kinetic equation can be in line with Odqvist's law for viscoplasticity and Prandtl-Reussmore » theory. Free surfaces (external surfaces or internal cracks/voids) are treated in the model. Deformation caused by a misfitting spherical precipitate in an elasto-plastic matrix is studied by large-scale three-dimensional simulations in four different regimes in terms of the matrix: (a) elasto-perfectly-plastic, (b) elastoplastic with linear hardening, (c) elastoplastic with power-law hardening, and (d) elasto-perfectly-plastic with a free surface. The results are compared with analytical/numerical solutions of Lee et al. for (a-c) and analytical solution derived in this work for (d). Additionally, the J integral of a fixed crack is calculated in the phase-field model and discussed in the context of fracture mechanics.« less

Modeling elasto-viscoplasticity in a consistent phase field framework

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cheng, Tian -Le; Wen, You -Hai; Hawk, Jeffrey A.

Existing continuum level phase field plasticity theories seek to solve plastic strain by minimizing the shear strain energy. However, rigorously speaking, for thermodynamic consistency it is required to minimize the total strain energy unless there is proof that hydrostatic strain energy is independent of plastic strain which is unfortunately absent. In this work, we extend the phase-field microelasticity theory of Khachaturyan et al. by minimizing the total elastic energy with constraint of incompressibility of plastic strain. We show that the flow rules derived from the Ginzburg-Landau type kinetic equation can be in line with Odqvist's law for viscoplasticity and Prandtl-Reussmore » theory. Free surfaces (external surfaces or internal cracks/voids) are treated in the model. Deformation caused by a misfitting spherical precipitate in an elasto-plastic matrix is studied by large-scale three-dimensional simulations in four different regimes in terms of the matrix: (a) elasto-perfectly-plastic, (b) elastoplastic with linear hardening, (c) elastoplastic with power-law hardening, and (d) elasto-perfectly-plastic with a free surface. The results are compared with analytical/numerical solutions of Lee et al. for (a-c) and analytical solution derived in this work for (d). Additionally, the J integral of a fixed crack is calculated in the phase-field model and discussed in the context of fracture mechanics.« less

Recent developments in minimal processing: a tool to retain nutritional quality of food.

PubMed

Pasha, Imran; Saeed, Farhan; Sultan, M Tauseef; Khan, Moazzam Rafiq; Rohi, Madiha

2014-01-01

The modernization during the last century resulted in urbanization coupled with modifications in lifestyles and dietary habits. In the same era, industrial developments made it easier to meet the requirements for processed foods. However, consumers are now interested in minimally processed foods owing to increase in their awareness to have fruits and vegetables with superior quality, and natural integrity with fewer additives. The food products deteriorate as a consequence of physiological aging, biochemical changes, high respiration rat,e and high ethylene production. These factors contribute substantially to discoloration, loss of firmness, development of off-flavors, acidification, and microbial spoilage. Simultaneously, food processors are using emerging approaches to process perishable commodities, along with enhanced nutritional and sensorial quality. The present review article is an effort to utilize the modern approaches to minimize the processing and deterioration. The techniques discussed in this paper include chlorination, ozonation, irradiation, photosensitization, edible coating, natural preservative use, high-pressure processing, microwave heating, ohmic heating, and hurdle technology. The consequences of these techniques on shelf-life stability, microbial safety, preservation of organoleptic and nutritional quality, and residue avoidance are the limelight of the paper. Moreover, the discussion has been made on the feasibility and operability of these techniques in modern-day processing.

Category inference as a function of correlational structure, category discriminability, and number of available cues.

PubMed

Lancaster, Matthew E; Shelhamer, Ryan; Homa, Donald

2013-04-01

Two experiments investigated category inference when categories were composed of correlated or uncorrelated dimensions and the categories overlapped minimally or moderately. When the categories minimally overlapped, the dimensions were strongly correlated with the category label. Following a classification learning phase, subsequent transfer required the selection of either a category label or a feature when one, two, or three features were missing. Experiments 1 and 2 differed primarily in the number of learning blocks prior to transfer. In each experiment, the inference of the category label or category feature was influenced by both dimensional and category correlations, as well as their interaction. The number of cues available at test impacted performance more when the dimensional correlations were zero and category overlap was high. However, a minimal number of cues were sufficient to produce high levels of inference when the dimensions were highly correlated; additional cues had a positive but reduced impact, even when overlap was high. Subjects were generally more accurate in inferring the category label than a category feature regardless of dimensional correlation, category overlap, or number of cues available at test. Whether the category label functioned as a special feature or not was critically dependent upon these embedded correlations, with feature inference driven more strongly by dimensional correlations.

Energy-efficient ZigBee-based wireless sensor network for track bicycle performance monitoring.

PubMed

Gharghan, Sadik K; Nordin, Rosdiadee; Ismail, Mahamod

2014-08-22

In a wireless sensor network (WSN), saving power is a vital requirement. In this paper, a simple point-to-point bike WSN was considered. The data of bike parameters, speed and cadence, were monitored and transmitted via a wireless communication based on the ZigBee protocol. Since the bike parameters are monitored and transmitted on every bike wheel rotation, this means the sensor node does not sleep for a long time, causing power consumption to rise. Therefore, a newly proposed algorithm, known as the Redundancy and Converged Data (RCD) algorithm, was implemented for this application to put the sensor node into sleep mode while maintaining the performance measurements. This is achieved by minimizing the data packets transmitted as much as possible and fusing the data of speed and cadence by utilizing the correlation measurements between them to minimize the number of sensor nodes in the network to one node, which results in reduced power consumption, cost, and size, in addition to simpler hardware implementation. Execution of the proposed RCD algorithm shows that this approach can reduce the current consumption to 1.69 mA, and save 95% of the sensor node energy. Also, the comparison results with different wireless standard technologies demonstrate minimal current consumption in the sensor node.

Cell-free protein synthesis in micro compartments: building a minimal cell from biobricks.

PubMed

Jia, Haiyang; Heymann, Michael; Bernhard, Frank; Schwille, Petra; Kai, Lei

2017-10-25

The construction of a minimal cell that exhibits the essential characteristics of life is a great challenge in the field of synthetic biology. Assembling a minimal cell requires multidisciplinary expertise from physics, chemistry and biology. Scientists from different backgrounds tend to define the essence of 'life' differently and have thus proposed different artificial cell models possessing one or several essential features of living cells. Using the tools and methods of molecular biology, the bottom-up engineering of a minimal cell appears in reach. However, several challenges still remain. In particular, the integration of individual sub-systems that is required to achieve a self-reproducing cell model presents a complex optimization challenge. For example, multiple self-organisation and self-assembly processes have to be carefully tuned. We review advances and developments of new methods and techniques, for cell-free protein synthesis as well as micro-fabrication, for their potential to resolve challenges and to accelerate the development of minimal cells. Copyright © 2017 Elsevier B.V. All rights reserved.

Response of microbial growth to orthophosphate and organic carbon influx in copper and plastic based plumbing water systems.

PubMed

Park, Se-Keun; Kim, Yeong-Kwan; Choi, Sung-Chan

2008-07-01

Consequences of orthophosphate addition for corrosion control in water distribution pipes with respect to microbial growth were investigated using batch and dynamic tests. Batch tests showed that the release of copper in either low or high organic carbon content water was decreased by 69% and 56% with addition 206 microg PO(4)-P, respectively. Dosing of orthophosphate against corrosion did not increase microbial growth potential in the water and in the biofilm in both corroded and uncorroded systems receiving tap water with a low content of organic carbon and of biodegradable organic fraction. However, in tap water having a high concentration of organic carbon from acetate addition, orthophosphate addition promoted the growth of bacteria, allowed more bacteria to assemble on corroded and uncorroded surfaces, and increased the consumption of organic carbon. Orthophosphate consumption did not exceed 1% of the amount of easily biodegradable organic carbon required for microbial growth, and the orthophosphate demand for corrosion control greatly exceeded the nutritional requirement of microbial growth. The results of the dynamic tests demonstrated that there was a significant effect of interaction between biodegradable organic carbon and orthophosphate on biofilm growth, whereby the effect of orthophosphate flux on microbial growth was dependent on the levels of biodegradable organic carbon. Controlling an easily biodegradable organic carbon would be therefore necessary to minimize the microbial growth potential induced by orthophosphate-based anticorrosion treatment.

Text-Based On-Line Conferencing: A Conceptual and Empirical Analysis Using a Minimal Prototype.

ERIC Educational Resources Information Center

McCarthy, John C.; And Others

1993-01-01

Analyzes requirements for text-based online conferencing through the use of a minimal prototype. Topics discussed include prototyping with a minimal system; text-based communication; the system as a message passer versus the system as a shared data structure; and three exercises that showed how users worked with the prototype. (Contains 61…

Joint Geophysical Inversion With Multi-Objective Global Optimization Methods

NASA Astrophysics Data System (ADS)

Lelievre, P. G.; Bijani, R.; Farquharson, C. G.

2015-12-01

Pareto multi-objective global optimization (PMOGO) methods generate a suite of solutions that minimize multiple objectives (e.g. data misfits and regularization terms) in a Pareto-optimal sense. Providing a suite of models, as opposed to a single model that minimizes a weighted sum of objectives, allows a more complete assessment of the possibilities and avoids the often difficult choice of how to weight each objective. We are applying PMOGO methods to three classes of inverse problems. The first class are standard mesh-based problems where the physical property values in each cell are treated as continuous variables. The second class of problems are also mesh-based but cells can only take discrete physical property values corresponding to known or assumed rock units. In the third class we consider a fundamentally different type of inversion in which a model comprises wireframe surfaces representing contacts between rock units; the physical properties of each rock unit remain fixed while the inversion controls the position of the contact surfaces via control nodes. This third class of problem is essentially a geometry inversion, which can be used to recover the unknown geometry of a target body or to investigate the viability of a proposed Earth model. Joint inversion is greatly simplified for the latter two problem classes because no additional mathematical coupling measure is required in the objective function. PMOGO methods can solve numerically complicated problems that could not be solved with standard descent-based local minimization methods. This includes the latter two classes of problems mentioned above. There are significant increases in the computational requirements when PMOGO methods are used but these can be ameliorated using parallelization and problem dimension reduction strategies.

Miniature X-Ray Bone Densitometer

NASA Technical Reports Server (NTRS)

Charles, Harry K., Jr.

1999-01-01

The purpose of the Dual Energy X-ray Absorptiometry (DEXA) project is to design, build, and test an advanced X-ray absorptiometry scanner capable of being used to monitor the deleterious effects of weightlessness on the human musculoskeletal system during prolonged spaceflight. The instrument is based on the principles of dual energy x-ray absorptiometry and is designed not only to measure bone, muscle, and fat masses but also to generate structural information about these tissues so that the effects on mechanical integrity may be assessed using biomechanical principles. A skeletal strength assessment could be particularly important for an astronaut embarking on a remote planet where the consequences of a fragility fracture may be catastrophic. The scanner will employ multiple projection images about the long axis of the scanned subject to provide geometric properties in three dimensions, suitable for a three-dimensional structural analysis of the scanned region. The instrument will employ advanced fabrication techniques to minimize volume and mass (100 kg current target with a long-term goal of 60 kg) of the scanner as appropriate for the space environment, while maintaining the required mechanical stability for high precision measurement. The unit will have the precision required to detect changes in bone mass and geometry as small as 1% and changes in muscle mass as small as 5%. As the system evolves, advanced electronic fabrication technologies such as chip-on-board and multichip modules will be combined with commercial (off-the-shelf) parts to produce a reliable, integrated system which not only minimizes size and weight, but, because of its simplicity, is also cost effective to build and maintain. Additionally, the system is being designed to minimize power consumption. Methods of heat dissipation and mechanical stowage (for the unit when not in use) are being optimized for the space environment.

Deflection-Compensating Beam for use inside a Cylinder

NASA Technical Reports Server (NTRS)

Goodman, Dwight; Myers, Neill; Herren, Kenneth

2008-01-01

A design concept for a beam for a specific application permits variations and options for satisfying competing requirements to minimize certain deflections under load and to minimize the weight of the beam. In the specific application, the beam is required to serve as a motion-controlled structure for supporting a mirror for optical testing in the lower third portion of a horizontal, cylindrical vacuum chamber. The cylindrical shape of the chamber is fortuitous in that it can be (and is) utilized as an essential element of the deflection-minimizing design concept. The beam is, more precisely, a table-like structure comprising a nominally flat, horizontal portion with vertical legs at its ends. The weights of the beam and whatever components it supports are reacted by the contact forces between the lower ends of the legs and the inner cylindrical chamber wall. Whereas the bending moments arising from the weights contribute to a beam deflection that is concave with its lowest point at midlength, the bending moments generated by the contact forces acting on the legs contribute to a beam deflection that is convex with its highest point at midlength. In addition, the bending of the legs in response to the weights causes the lower ends of the legs to slide downward on the cylindrical wall. By taking the standard beam-deflection equations, combining them with the geometric relationships among the legs and the horizontal portion of the beam, and treating the sliding as a component of deflection, it is possible to write an equation for the net vertical deflection as a function of the load and of position along the beam. A summary of major conclusions drawn from the equation characterization is included.

Robotic-assisted laparoscopic partial nephrectomy: initial experience in Brazil and a review of the literature.

PubMed

Passerotti, Carlo Camargo; Pessoa, Rodrigo; da Cruz, Jose Arnaldo Shiomi; Okano, Marcelo Takeo; Antunes, Alberto Azoubel; Nesrallah, Adriano Joao; Dall'oglio, Marcos Francisco; Andrade, Enrico; Srougi, Miguel

2012-01-01

Partial nephrectomy has become the standard of care for renal tumors less than 4 cm in diameter. Controversy still exists, however, regarding the best surgical approach, especially when minimally invasive techniques are taken into account. Robotic-assisted laparoscopic partial nephrectomy (RALPN) has emerged as a promising technique that helps surgeons achieve the standards of open partial nephrectomy care while offering a minimally invasive approach. The objective of the present study was to describe our initial experience with robotic-assisted laparoscopic partial nephrectomy and extensively review the pertinent literature. Between August 2009 and February 2010, eight consecutive selected patients with contrast enhancing renal masses observed by CT were submitted to RALPN in a private institution. In addition, we collected information on the patients ' demographics, preoperative tumor characteristics and detailed operative, postoperative and pathological data. In addition, a PubMed search was performed to provide an extensive review of the robotic-assisted laparoscopic partial nephrectomy literature. Seven patients had RALPN on the left or right sides with no intraoperative complications. One patient was electively converted to a robotic-assisted radical nephrectomy. The operative time ranged from 120 to 300 min, estimated blood loss (EBL) ranged from 75 to 400 mL and, in five cases, the warm ischemia time (WIT) ranged from 18 to 32 min. Two patients did not require any clamping. Overall, no transfusions were necessary, and there were no intraoperative complications or adverse postoperative clinical events. All margins were negative, and all patients were disease-free at the 6-month follow-up. Robotic-assisted laparoscopic partial nephrectomy is a feasible and safe approach to small renal cortical masses. Further prospective studies are needed to compare open partial nephrectomy with its minimally invasive counterparts.

Rendezvous strategy impacts on CTV avionics design, system reliability requirements, and available collision avoidance maneuvers

NASA Technical Reports Server (NTRS)

Donovan, William J.; Davis, John E.

1991-01-01

Rockwell International is conducting an ongoing program to develop avionics architectures that provide high intrinsic value while meeting all mission objectives. Studies are being conducted to determine alternative configurations that have low life-cycle cost and minimum development risk, and that minimize launch delays while providing the reliability level to assure a successful mission. This effort is based on four decades of providing ballistic missile avionics to the United States Air Force and has focused on the requirements of the NASA Cargo Transfer Vehicle (CTV) program in 1991. During the development of architectural concepts it became apparent that rendezvous strategy issues have an impact on the architecture of the avionics system. This is in addition to the expected impact on propulsion and electrical power duration, flight profiles, and trajectory during approach.

Experimental Validation of the Dynamic Inertia Measurement Method to Find the Mass Properties of an Iron Bird Test Article

NASA Technical Reports Server (NTRS)

Chin, Alexander W.; Herrera, Claudia Y.; Spivey, Natalie D.; Fladung, William A.; Cloutier, David

2015-01-01

The mass properties of an aerospace vehicle are required by multiple disciplines in the analysis and prediction of flight behavior. Pendulum oscillation methods have been developed and employed for almost a century as a means to measure mass properties. However, these oscillation methods are costly, time consuming, and risky. The NASA Armstrong Flight Research Center has been investigating the Dynamic Inertia Measurement, or DIM method as a possible alternative to oscillation methods. The DIM method uses ground test techniques that are already applied to aerospace vehicles when conducting modal surveys. Ground vibration tests would require minimal additional instrumentation and time to apply the DIM method. The DIM method has been validated on smaller test articles, but has not yet been fully proven on large aerospace vehicles.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harkenrider, Matthew M., E-mail: mharkenrider@lumc.edu; Alite, Fiori; Silva, Scott R.

Cervical cancer is a disease that requires considerable multidisciplinary coordination of care and labor in order to maximize tumor control and survival while minimizing treatment-related toxicity. As with external beam radiation therapy, the use of advanced imaging and 3-dimensional treatment planning has generated a paradigm shift in the delivery of brachytherapy for the treatment of cervical cancer. The use of image-based brachytherapy, most commonly with magnetic resonance imaging (MRI), requires additional attention and effort by the treating physician to prescribe dose to the proper volume and account for adjacent organs at risk. This represents a dramatic change from the classicmore » Manchester approach of orthogonal radiographic images and prescribing dose to point A. We reviewed the history and currently evolving data and recommendations for the clinical use of image-based brachytherapy with an emphasis on MRI-based brachytherapy.« less

Microbubble mediated dual-frequency high intensity focused ultrasound thrombolysis: An In vitro study

NASA Astrophysics Data System (ADS)

Suo, Dingjie; Jin, Zhiyang; Jiang, Xiaoning; Dayton, Paul A.; Jing, Yun

2017-01-01

High intensity focused ultrasound (HIFU) has recently emerged as a promising alternative approach for thrombolysis. However, the high acoustic energy required by HIFU could elicit thermal damage bioeffects, impeding the clinical translation of this technique. This paper investigates the use of dual-frequency focused ultrasound (DFFU) mediated by microbubbles (MBs) to minimize the acoustic power required for thrombolysis in vitro. It was found that MBs, with sufficient concentration, could significantly lower the power threshold for thrombolysis for both DFFU and single-frequency focused ultrasound (SFFU). In addition, SFFU needs about 96%-156% higher energy to achieve the same thrombolysis efficiency as that of DFFU. The thrombolysis efficiency is also found to increase with the duty cycle. The measured cavitation signals reveal that the enhanced inertial cavitation is likely responsible for the improved thrombolysis under DFFU and MBs.

Modular photovoltaic stand-alone systems: Phase 1

NASA Technical Reports Server (NTRS)

Naff, G. J.; Marshall, N. A.

1983-01-01

A family of modular stand-alone power systems that covered the range in power level from 1 kw to 14 kw was developed. Products within this family were required to be easily adaptable to different environments and applications, and were to be both reliable and cost effective. Additionally, true commonality in hardware was to be exploited, and unnecessary recurrence of design and development costs were to be minimized; thus improving hardware availability. Assurance of compatibility with large production runs, was also an underlying program goal. A secondary objective was to compile, evaluate, and determine the economic and technical status of available, and potentially available, technology options associated with the balance of systems (BOS) for stand-along photovoltaic (PV) power systems. The secondary objective not only directly supported the primary but additionally contributed to the definition and implementation of the BOS cost reduction plan.

Parallel architecture for rapid image generation and analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nerheim, R.J.

1987-01-01

A multiprocessor architecture inspired by the Disney multiplane camera is proposed. For many applications, this approach produces a natural mapping of processors to objects in a scene. Such a mapping promotes parallelism and reduces the hidden-surface work with minimal interprocessor communication and low-overhead cost. Existing graphics architectures store the final picture as a monolithic entity. The architecture here stores each object's image separately. It assembles the final composite picture from component images only when the video display needs to be refreshed. This organization simplifies the work required to animate moving objects that occlude other objects. In addition, the architecture hasmore » multiple processors that generate the component images in parallel. This further shortens the time needed to create a composite picture. In addition to generating images for animation, the architecture has the ability to decompose images.« less

Air Evaporation closed cycle water recovery technology - Advanced energy saving designs

NASA Technical Reports Server (NTRS)

Morasko, Gwyndolyn; Putnam, David F.; Bagdigian, Robert

1986-01-01

The Air Evaporation water recovery system is a visible candidate for Space Station application. A four-man Air Evaporation open cycle system has been successfully demonstrated for waste water recovery in manned chamber tests. The design improvements described in this paper greatly enhance the system operation and energy efficiency of the air evaporation process. A state-of-the-art wick feed design which results in reduced logistics requirements is presented. In addition, several design concepts that incorporate regenerative features to minimize the energy input to the system are discussed. These include a recuperative heat exchanger, a heat pump for energy transfer to the air heater, and solar collectors for evaporative heat. The addition of the energy recovery devices will result in an energy reduction of more than 80 percent over the systems used in earlier manned chamber tests.

Rheology and Extrusion of Cement-Fly Ashes Pastes

NASA Astrophysics Data System (ADS)

Micaelli, F.; Lanos, C.; Levita, G.

2008-07-01

The addition of fly ashes in cement pastes is tested to optimize the forming of cement based material by extrusion. Two sizes of fly ashes grains are examinated. The rheology of concentrated suspensions of ashes mixes is studied with a parallel plates rheometer. In stationary flow state, tested suspensions viscosities are satisfactorily described by the Krieger-Dougherty model. An "overlapped grain" suspensions model able to describe the bimodal suspensions behaviour is proposed. For higher values of solid volume fraction, Bingham viscoplastic behaviour is identified. Results showed that the plastic viscosity and plastic yield values present minimal values for the same optimal formulation of bimodal mixes. The rheological study is extended to more concentrated systems using an extruder. Finally it is observed that the addition of 30% vol. of optimized ashes mix determined a significant reduction of required extrusion load.

Design and Sizing of the Air Revitalization System for Altair Lunar Lander

NASA Technical Reports Server (NTRS)

Allada, Rama Kumar

2009-01-01

Designing closed-loop Air Revitalization Systems (ARS) for human spaceflight applications requires a delicate balance between designing for system robustness while minimizing system power and mass requirements. This presentation will discuss the design of the ARS for the Altair Lunar Lander. The presentation will illustrate how dynamic simulations, using Aspen Custom Modeler, were used to develop a system configuration with the ability to control atmospheric conditions under a wide variety of circumstances while minimizing system mass/volume and the impact on overall power requirements for the Lander architecture.

Analysis of environmental constraints on expanding reserves in current and future reservoirs in wetlands. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harder, B.J.

1995-03-01

Louisiana wetlands require careful management to allow exploitation of non-renewable resources without destroying renewable resources. Current regulatory requirements have been moderately successful in meeting this goal by restricting development in wetland habitats. Continuing public emphasis on reducing environmental impacts of resource development is causing regulators to reassess their regulations and operators to rethink their compliance strategies. We examined the regulatory system and found that reducing the number of applications required by going to a single application process and having a coherent map of the steps required for operations in wetland areas would reduce regulatory burdens. Incremental changes can be mademore » to regulations to allow one agency to be the lead for wetland permitting at minimal cost to operators. Operators need cost effective means of access that will reduce environmental impacts, decrease permitting time, and limit future liability. Regulators and industry must partner to develop incentive based regulations that can provide significant environmental impact reduction for minimal economic cost. In addition regulators need forecasts of future E&P trends to estimate the impact of future regulations. To determine future activity we attempted to survey potential operators when this approach was unsuccessful we created two econometric models of north and south Louisiana relating drilling activity, success ratio, and price to predict future wetland activity. Results of the econometric models indicate that environmental regulations have a small but statistically significant effect on drilling operations in wetland areas of Louisiana. We examined current wetland practices and evaluated those practices comparing environmental versus economic costs and created a method for ranking the practices.« less

Atomic precision etch using a low-electron temperature plasma

NASA Astrophysics Data System (ADS)

Dorf, L.; Wang, J.-C.; Rauf, S.; Zhang, Y.; Agarwal, A.; Kenney, J.; Ramaswamy, K.; Collins, K.

2016-03-01

Sub-nm precision is increasingly being required of many critical plasma etching processes in the semiconductor industry. Accurate control over ion energy and ion/radical composition is needed during plasma processing to meet these stringent requirements. Described in this work is a new plasma etch system which has been designed with the requirements of atomic precision plasma processing in mind. In this system, an electron sheet beam parallel to the substrate surface produces a plasma with an order of magnitude lower electron temperature Te (~ 0.3 eV) and ion energy Ei (< 3 eV without applied bias) compared to conventional radio-frequency (RF) plasma technologies. Electron beam plasmas are characterized by higher ion-to-radical fraction compared to RF plasmas, so a separate radical source is used to provide accurate control over relative ion and radical concentrations. Another important element in this plasma system is low frequency RF bias capability which allows control of ion energy in the 2-50 eV range. Presented in this work are the results of etching of a variety of materials and structures performed in this system. In addition to high selectivity and low controllable etch rate, an important requirement of atomic precision etch processes is no (or minimal) damage to the remaining material surface. It has traditionally not been possible to avoid damage in RF plasma processing systems, even during atomic layer etch. The experiments for Si etch in Cl2 based plasmas in the aforementioned etch system show that damage can be minimized if the ion energy is kept below 10 eV. Layer-by-layer etch of Si is also demonstrated in this etch system using electrical and gas pulsing.

Guiding gate-etch process development using 3D surface reaction modeling for 7nm and beyond

NASA Astrophysics Data System (ADS)

Dunn, Derren; Sporre, John R.; Deshpande, Vaibhav; Oulmane, Mohamed; Gull, Ronald; Ventzek, Peter; Ranjan, Alok

2017-03-01

Increasingly, advanced process nodes such as 7nm (N7) are fundamentally 3D and require stringent control of critical dimensions over high aspect ratio features. Process integration in these nodes requires a deep understanding of complex physical mechanisms to control critical dimensions from lithography through final etch. Polysilicon gate etch processes are critical steps in several device architectures for advanced nodes that rely on self-aligned patterning approaches to gate definition. These processes are required to meet several key metrics: (a) vertical etch profiles over high aspect ratios; (b) clean gate sidewalls free of etch process residue; (c) minimal erosion of liner oxide films protecting key architectural elements such as fins; and (e) residue free corners at gate interfaces with critical device elements. In this study, we explore how hybrid modeling approaches can be used to model a multi-step finFET polysilicon gate etch process. Initial parts of the patterning process through hardmask assembly are modeled using process emulation. Important aspects of gate definition are then modeled using a particle Monte Carlo (PMC) feature scale model that incorporates surface chemical reactions.1 When necessary, species and energy flux inputs to the PMC model are derived from simulations of the etch chamber. The modeled polysilicon gate etch process consists of several steps including a hard mask breakthrough step (BT), main feature etch steps (ME), and over-etch steps (OE) that control gate profiles at the gate fin interface. An additional constraint on this etch flow is that fin spacer oxides are left intact after final profile tuning steps. A natural optimization required from these processes is to maximize vertical gate profiles while minimizing erosion of fin spacer films.2

The molecular variability analysis of the RNA 3 of fifteen isolates of Prunus necrotic ringspot virus sheds light on the minimal requirements for the synthesis of its subgenomic RNA.

PubMed

Aparicio, Frederic; Pallás, Vicente

2002-01-01

The nucleotide sequences of the RNA 3 of fifteen isolates of Prunus necrotic ringspot virus (PNRSV) varying in the symptomatology they cause in six different Prunus spp. were determined. Analysis of the molecular variability has allowed, in addition to study the phylogenetic relationships among them, to evaluate the minimal requirements for the synthesis of the subgenomic RNA in Ilarvirus genus and their comparison to other members of the Bromoviridae family. Computer assisted comparisons led recently to Jaspars (Virus Genes 17, 233-242, 1998) to propose that a hairpin structure in viral minus strand RNA is required for subgenomic promoter activity of viruses from at least two, and possibly all five, genera in the family of Bromoviridae. For PNRSV and Apple mosaic virus two stable hairpins were proposed whereas for the rest of Ilarviruses and the other four genera of the Bromoviridae family only one stable hairpin was predicted. Comparative analysis of this region among the fifteen PNRSV isolates characterized in this study revealed that two of them showed a 12-nt deletion that led to the disappearance of the most proximal hairpin to the initiation site. Interestingly, the only hairpin found in these two isolates is very similar in primary and secondary structure to the one previously shown in Brome mosaic virus to be required for the synthesis of the subgenomic RNA. In this hairpin, the molecular diversity was concentrated mostly at the loop whereas compensatory mutations were observed at the base of the stem strongly suggesting its functional relevance. The evolutionary implications of these observations are discussed.

Elective change of surgeon during the OR day has an operationally negligible impact on turnover time.

PubMed

Austin, Thomas M; Lam, Humphrey V; Shin, Naomi S; Daily, Bethany J; Dunn, Peter F; Sandberg, Warren S

2014-08-01

To compare turnover times for a series of elective cases with surgeons following themselves with turnover times for a series of previously scheduled elective procedures for which the succeeding surgeon differed from the preceding surgeon. Retrospective cohort study. University-affiliated teaching hospital. The operating room (OR) statistical database was accessed to gather 32 months of turnover data from a large academic institution. Turnover time data for the same-surgeon and surgeon-swap groups were batched by month to minimize autocorrelation and achieve data normalization. Two-way analysis of variance (ANOVA) using the monthly batched data was performed with surgeon swapping and changes in procedure category as variables of turnover time. Similar analyses were performed using individual surgical services, hourly time intervals during the surgical day, and turnover frequency per OR as additional covariates to surgeon swapping. The mean (95% confidence interval [CI]) same-surgeon turnover time was 43.6 (43.2 - 44.0) minutes versus 51.0 (50.5 - 51.6) minutes for a planned surgeon swap (P < 0.0001). This resulted in a difference (95% CI) of 7.4 (6.8 - 8.1) minutes. The exact increase in turnover time was dependent on surgical service, change in subsequent procedure type, time of day when the turnover occurred, and turnover frequency. The investigated institution averages 2.5 cases per OR per day. The cumulative additional turnover time (far less than one hour per OR per day) for switching surgeons definitely does not allow the addition of another elective procedure if the difference could be eliminated. A flexible scheduling policy allowing surgeon swapping rather than requiring full blocks incurs minimal additional staffed time during the OR day while allowing the schedule to be filled with available elective cases. Copyright © 2014 Elsevier Inc. All rights reserved.

Optimization of fertilization characteristics of urine by addition of Nitrosomonas europaea bio-seed.

PubMed

Hashemi, Shervin; Han, Mooyoung; Kim, Tschungil

2016-10-01

Because of the high concentration of nutrients in human urine, its utilization as an organic fertilizer has been notable throughout history. However, the nitrogen compounds in urine are not stable. Therefore, to convert urine into a suitable fertilizer, it is important to stabilize and adjust unstable nitrogen compounds such as ammonia. Because nitrification can influence the nitrogen profile, the use of nitrifying microorganisms can be useful for stabilizing the nitrogen profile of urine. This study investigated the changes in nitrogen compounds in pure urine and examined the effect of adding Nitrosomonas europaea bio-seed solution on these changes. It was found that the addition of bio-seed could reduce nitrogen loss as well as the time required to stabilize the nitrogen profile. Furthermore, the optimum concentration of bio-seed (6 × 10(5) N. europaea cells L(-1) ) that not only leads to the least nutrient loss but also results in an adequate nitrate/ammonium ratio and regulates the amount of nitrate produced, thereby preventing over-fertilization, was determined. At this concentration, no dilution or dewatering is required, thus minimizing water and energy consumption. Usage of the optimum of concentration of bio-seed will also eliminate the need for inorganic chemical additives. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

36 CFR 223.218 - Consistency with plans, environmental standards, and other management requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) Minimize soil erosion; (e) Maintain favorable conditions of water flow and quality; (f) Minimize adverse effects on, protect, or enhance other national forest resources, uses, and improvements; and (g) Deposit...

Extracellular space preservation aids the connectomic analysis of neural circuits

PubMed Central

Pallotto, Marta; Watkins, Paul V; Fubara, Boma; Singer, Joshua H; Briggman, Kevin L

2015-01-01

Dense connectomic mapping of neuronal circuits is limited by the time and effort required to analyze 3D electron microscopy (EM) datasets. Algorithms designed to automate image segmentation suffer from substantial error rates and require significant manual error correction. Any improvement in segmentation error rates would therefore directly reduce the time required to analyze 3D EM data. We explored preserving extracellular space (ECS) during chemical tissue fixation to improve the ability to segment neurites and to identify synaptic contacts. ECS preserved tissue is easier to segment using machine learning algorithms, leading to significantly reduced error rates. In addition, we observed that electrical synapses are readily identified in ECS preserved tissue. Finally, we determined that antibodies penetrate deep into ECS preserved tissue with only minimal permeabilization, thereby enabling correlated light microscopy (LM) and EM studies. We conclude that preservation of ECS benefits multiple aspects of the connectomic analysis of neural circuits. DOI: http://dx.doi.org/10.7554/eLife.08206.001 PMID:26650352

International Space Station (ISS) Advanced Recycle Filter Tank Assembly (ARFTA)

NASA Technical Reports Server (NTRS)

Nasrullah, Mohammed K.

2013-01-01

The International Space Station (ISS) Recycle Filter Tank Assembly (RFTA) provides the following three primary functions for the Urine Processor Assembly (UPA): volume for concentrating/filtering pretreated urine, filtration of product distillate, and filtration of the Pressure Control and Pump Assembly (PCPA) effluent. The RFTAs, under nominal operations, are to be replaced every 30 days. This poses a significant logistical resupply problem, as well as cost in upmass and new tanks purchase. In addition, it requires significant amount of crew time. To address and resolve these challenges, NASA required Boeing to develop a design which eliminated the logistics and upmass issues and minimize recurring costs. Boeing developed the Advanced Recycle Filter Tank Assembly (ARFTA) that allowed the tanks to be emptied on-orbit into disposable tanks that eliminated the need for bringing the fully loaded tanks to earth for refurbishment and relaunch, thereby eliminating several hundred pounds of upmass and its associated costs. The ARFTA will replace the RFTA by providing the same functionality, but with reduced resupply requirements

Neuronal and non-neuronal signals regulate Caernorhabditis elegans avoidance of contaminated food.

PubMed

Anderson, Alexandra; McMullan, Rachel

2018-07-19

One way in which animals minimize the risk of infection is to reduce their contact with contaminated food. Here, we establish a model of pathogen-contaminated food avoidance using the nematode worm Caernorhabditis elegans We find that avoidance of pathogen-contaminated food protects C. elegans from the deleterious effects of infection and, using genetic approaches, demonstrate that multiple sensory neurons are required for this avoidance behaviour. In addition, our results reveal that the avoidance of contaminated food requires bacterial adherence to non-neuronal cells in the tail of C. elegans that are also required for the cellular immune response. Previous studies in C. elegans have contributed significantly to our understanding of molecular and cellular basis of host-pathogen interactions and our model provides a unique opportunity to gain basic insights into how animals avoid contaminated food.This article is part of the Theo Murphy meeting issue 'Evolution of pathogen and parasite avoidance behaviours'. © 2018 The Authors.

Spacecraft Jitter Attenuation Using Embedded Piezoelectric Actuators

NASA Technical Reports Server (NTRS)

Belvin, W. Keith

1995-01-01

Remote sensing from spacecraft requires precise pointing of measurement devices in order to achieve adequate spatial resolution. Unfortunately, various spacecraft disturbances induce vibrational jitter in the remote sensing instruments. The NASA Langley Research Center has performed analysis, simulations, and ground tests to identify the more promising technologies for minimizing spacecraft pointing jitter. These studies have shown that the use of smart materials to reduce spacecraft jitter is an excellent match between a maturing technology and an operational need. This paper describes the use of embedding piezoelectric actuators for vibration control and payload isolation. In addition, recent advances in modeling, simulation, and testing of spacecraft pointing jitter are discussed.

Chemical fractionation-enhanced structural characterization of marine dissolved organic matter

NASA Astrophysics Data System (ADS)

Arakawa, N.; Aluwihare, L.

2016-02-01

Describing the molecular fingerprint of dissolved organic matter (DOM) requires sample processing methods and separation techniques that can adequately minimize its complexity. We have employed acid hydrolysis as a way to make the subcomponents of marine solid phase-extracted (PPL) DOM more accessible to analytical techniques. Using a combination of NMR and chemical derivatization or reduction analyzed by comprehensive (GCxGC) gas chromatography, we observed chemical features strikingly similar to terrestrial DOM. In particular, we observed reduced alicylic hydrocarbons believed to be the backbone of previously identified carboxylic rich alicyclic material (CRAM). Additionally, we found carbohydrates, amino acids and small lipids and acids.

Note: Micro-channel array crucible for isotope-resolved laser spectroscopy of high-temperature atomic beams

DOE PAGES

Lebedev, Vyacheslav; Bartlett, Joshua H.; Malyzhenkov, Alexander; ...

2017-12-06

Here, we present a novel compact design for a multichannel atomic oven which generates collimated beams of refractory atoms for fieldable laser spectroscopy. Using this resistively heated crucible, we demonstrate spectroscopy of an erbium sample at 1300 °C with improved isotopic resolution with respect to a single-channel design. In addition, our oven has a high thermal efficiency. By minimizing the surface area of the crucible, we achieve 2000 °C at 140 W of applied electrical power. As a result, the design does not require any active cooling and is compact enough to allow for its incorporation into fieldable instruments.

Investigating Dielectric and Metamaterial Effects in a Terahertz Traveling-Wave Tube Amplifier

NASA Technical Reports Server (NTRS)

Starinshak, David P.; Wilson, Jeffrey D.

2008-01-01

Adding material enhancements to a terahertz traveling-wave tube amplifier is investigated. Isotropic dielectrics, negative-index metamaterials, and anisotropic crystals are simulated, and plans to increase the efficiency of the device are discussed. Early results indicate that adding dielectric to the curved sections of the serpentine-shaped slow-wave circuit produce optimal changes in the cold-test characteristics of the device and a minimal drop in operating frequency. Additional results suggest that materials with simultaneously small relative permittivities and electrical conductivities are best suited for increasing the efficiency of the device. More research is required on the subject, and recommendations are given to determine the direction.

Control of integrated micro-resonator wavelength via balanced homodyne locking.

PubMed

Cox, Jonathan A; Lentine, Anthony L; Trotter, Douglas C; Starbuck, Andrew L

2014-05-05

We describe and experimentally demonstrate a method for active control of resonant modulators and filters in an integrated photonics platform. Variations in resonance frequency due to manufacturing processes and thermal fluctuations are corrected by way of balanced homodyne locking. The method is compact, insensitive to intensity fluctuations, minimally disturbs the micro-resonator, and does not require an arbitrary reference to lock. We demonstrate long-term stable locking of an integrated filter to a laser swept over 1.25 THz. In addition, we show locking of a modulator with low bit error rate while the chip temperature is varied from 5 to 60° C.

AEROSOL PARTICLE COLLECTOR DESIGN STUDY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, S; Richard Dimenna, R

2007-09-27

A computational evaluation of a particle collector design was performed to evaluate the behavior of aerosol particles in a fast flowing gas stream. The objective of the work was to improve the collection efficiency of the device while maintaining a minimum specified air throughput, nominal collector size, and minimal power requirements. The impact of a range of parameters was considered subject to constraints on gas flow rate, overall collector dimensions, and power limitations. Potential improvements were identified, some of which have already been implemented. Other more complex changes were identified and are described here for further consideration. In addition, fruitfulmore » areas for further study are proposed.« less

Parenting and Childhood Chronicity: making visible the invisible work.

PubMed

Ray, Lynne D

2002-12-01

The work required to raise a child with a chronic illness or disability is above and beyond that of raising a typical child. This article presents a model, Parenting and Childhood Chronicity (PACC), that was developed during an interpretive study with 43 parents of 34 children (aged 15 months to 16 years) with various chronic conditions, is presented. "Special needs parenting" describes the additional care that a child needs and includes medical care, parenting plus, and working the systems. "Minimizing consequences" reflects the struggle to balance the rest of family life and includes parenting siblings, maintaining relationships, and keeping yourself going. Copyright 2002, Elsevier Science (USA). All rights reserved.

A wave shaping approach of ferrite inductors exhibiting hysteresis using orthogonal field bias

NASA Astrophysics Data System (ADS)

Adly, A. A.; Abd-El-Hafiz, S. K.; Mahgoub, A. O.

2018-05-01

Advances in power electronic systems have considerably contributed to a wide spectrum of applications. In most power electronic circuits, inductors play crucial functions. Utilization of ferrite cores becomes a must when large inductances are required. Nevertheless, this results in an additional complexity due to their hysteresis nature. Recently, an efficient approach for modeling vector hysteresis using tri-node Hopfield neural networks (HNNs) has been introduced. This paper presents a wave shaping approach using hollow cylindrical ferrite core inductors having axial and toroidal windings. The approach investigates the possibility of tuning the inductor permeability to minimize circuit harmonics. Details of the approach are given in the paper.

Note: Micro-channel array crucible for isotope-resolved laser spectroscopy of high-temperature atomic beams

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lebedev, Vyacheslav; Bartlett, Joshua H.; Malyzhenkov, Alexander

Here, we present a novel compact design for a multichannel atomic oven which generates collimated beams of refractory atoms for fieldable laser spectroscopy. Using this resistively heated crucible, we demonstrate spectroscopy of an erbium sample at 1300 °C with improved isotopic resolution with respect to a single-channel design. In addition, our oven has a high thermal efficiency. By minimizing the surface area of the crucible, we achieve 2000 °C at 140 W of applied electrical power. As a result, the design does not require any active cooling and is compact enough to allow for its incorporation into fieldable instruments.

A Framework for the Evaluation of the Cost and Benefits of Microgrids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morris, Greg Young; Abbey, Chad; Joos, Geza

2011-07-15

A Microgrid is recognized as an innovative technology to help integrate renewables into distribution systems and to provide additional benefits to a variety of stakeholders, such as offsetting infrastructure investments and improving the reliability of the local system. However, these systems require additional investments for control infrastructure, and as such, additional costs and the anticipated benefits need to be quantified in order to determine whether the investment is economically feasible. This paper proposes a methodology for systematizing and representing benefits and their interrelationships based on the UML Use Case paradigm, which allows complex systems to be represented in a concise,more » elegant format. This methodology is demonstrated by determining the economic feasibility of a Microgrid and Distributed Generation installed on a typical Canadian rural distribution system model as a case study. The study attempts to minimize the cost of energy served to the community, considering the fixed costs associated with Microgrids and Distributed Generation, and suggests benefits to a variety of stakeholders.« less

WASTE MINIMIZATION AUDIT REPORT: CASE STUDIES OF MINIMIZATION OF SOLVENT WASTES AND ELECTROPLATING WASTES AT A DOD (DEPARTMENT OF DEFENSE) INSTALLATION

EPA Science Inventory

The report results of a waste minimization audit carried out in 1987 at a tank reconditioning facility operated by the DOD. The audit team developed recommendations for reducing the generation FOO6 wastewater treatment sludge, and FOO2, and FOO4 solvent wastes. In addition to det...

Progress in Developing Transfer Functions for Surface Scanning Eddy Current Inspections

NASA Astrophysics Data System (ADS)

Shearer, J.; Heebl, J.; Brausch, J.; Lindgren, E.

2009-03-01

As US Air Force (USAF) aircraft continue to age, additional inspections are required for structural components. The validation of new inspections typically requires a capability demonstration of the method using representative structure with representative damage. To minimize the time and cost required to prepare such samples, Electric Discharge machined (EDM) notches are commonly used to represent fatigue cracks in validation studies. However, the sensitivity to damage typically changes as a function of damage type. This requires a mathematical relationship to be developed between the responses from the two different flaw types to enable the use of EDM notched samples to validate new inspections. This paper reviews progress to develop transfer functions for surface scanning eddy current inspections of aluminum and titanium alloys found in structural aircraft components. Multiple samples with well characterized grown fatigue cracks and master gages with EDM notches, both with a range of flaw sizes, were used to collect flaw signals with USAF field inspection equipment. Analysis of this empirical data was used to develop a transfer function between the response from the EDM notches and grown fatigue cracks.

Molten Metal Treatment by Salt Fluxing with Low Environmental Emissions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yogeshwar Sahai

2007-07-31

Abstract: Chlorine gas is traditionally used for fluxing of aluminum melt for removal of alkali and alkaline earth elements. However this results in undesirable emissions of particulate matter and gases such as HCl and chlorine, which are often at unacceptable levels. Additionally, chlorine gas is highly toxic and its handling, storage, and use pose risks to employees and the local community. Holding of even minimal amounts of chlorine necessitates extensive training for all plant employees. Fugitive emissions from chlorine usage within the plant cause accelerated corrosion of plant equipment. The Secondary Aluminum Maximum Achievable Control Technology (MACT) under the Cleanmore » Air Act, finalized in March 2000 has set very tough new limits on particulate matter (PM) and total hydrogen chloride emissions from aluminum melting and holding furnaces. These limits are 0.4 and 0.1 lbs per ton of aluminum for hydrogen chloride and particulate emissions, respectively. Assuming new technologies for meeting these limits can be found, additional requirements under the Clean Air Act (Prevention of Significant Deterioration and New Source Review) trigger Best Available Control Technology (BACT) for new sources with annual emissions (net emissions not expressed per ton of production) over specified amounts. BACT currently is lime coated bag-houses for control of particulate and HCl emissions. These controls are expensive, difficult to operate and maintain, and result in reduced American competitiveness in the global economy. Solid salt fluxing is emerging as a viable option for the replacement of chlorine gas fluxing, provided emissions can be consistently maintained below the required levels. This project was a cooperative effort between the Ohio State University and Alcoa to investigate and optimize the effects of solid chloride flux addition in molten metal for alkali impurity and non-metallic inclusion removal minimizing dust and toxic emissions and maximizing energy conservation. In this program, the salt metal interactions were studies and the emissions at laboratory scale at OSU were monitored. The goal of the project was to obtain a fundamental understanding, based on first principles, of the pollutant formation that occurs when the salts are used in furnaces. This information will be used to control process parameters so that emissions are consistently below the required levels. The information obtained in these experiments will be used in industrial furnaces at aluminum plants and which will help in optimizing the process.« less

Evolution of the INMARSAT aeronautical system: Service, system, and business considerations

NASA Technical Reports Server (NTRS)

Sengupta, Jay R.

1995-01-01

A market-driven approach was adopted to develop enhancements to the Inmarsat-Aeronautical system, to address the requirements of potential new market segments. An evolutionary approach and well differentiated product/service portfolio was required, to minimize system upgrade costs and market penetration, respectively. The evolved system definition serves to minimize equipment cost/size/mass for short/medium range aircraft, by reducing the antenna gain requirement and relaxing the performance requirements for non safety-related communications. A validation program involving simulation, laboratory tests, over-satellite tests and flight trials is being conducted to confirm the system definition. Extensive market research has been conducted to determine user requirements and to quantify market demand for future Inmarsat Aero-1 AES, using sophisticated computer assisted survey techniques.

Turbulence flight director analysis and preliminary simulation

NASA Technical Reports Server (NTRS)

Johnson, D. E.; Klein, R. E.

1974-01-01

A control column and trottle flight director display system is synthesized for use during flight through severe turbulence. The column system is designed to minimize airspeed excursions without overdriving attitude. The throttle system is designed to augment the airspeed regulation and provide an indication of the trim thrust required for any desired flight path angle. Together they form an energy management system to provide harmonious display indications of current aircraft motions and required corrective action, minimize gust upset tendencies, minimize unsafe aircraft excursions, and maintain satisfactory ride qualities. A preliminary fixed-base piloted simulation verified the analysis and provided a shakedown for a more sophisticated moving-base simulation to be accomplished next. This preliminary simulation utilized a flight scenario concept combining piloting tasks, random turbulence, and discrete gusts to create a high but realistic pilot workload conducive to pilot error and potential upset. The turbulence director (energy management) system significantly reduced pilot workload and minimized unsafe aircraft excursions.

Neighboring Extremal Guidance for Systems with Piecewise Linear Control Using Time As the Reference Variable

DTIC Science & Technology

1993-05-01

obtained to provide a nominal control history . The guidance law is found by minimizing the V second variation of the suboptimal trajectory...deviations from the suboptimal trajectory to required changes in the nominal control history . The deviations from the suboptimal trajectory, used together...with the precomputed gains, determines the change in the nominal control history required to meet the final constraints while minimizing the change in

Real time selective harmonic minimization for multilevel inverters using genetic algorithm and artifical neural network angle generation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Filho, Faete J; Tolbert, Leon M; Ozpineci, Burak

2012-01-01

The work developed here proposes a methodology for calculating switching angles for varying DC sources in a multilevel cascaded H-bridges converter. In this approach the required fundamental is achieved, the lower harmonics are minimized, and the system can be implemented in real time with low memory requirements. Genetic algorithm (GA) is the stochastic search method to find the solution for the set of equations where the input voltages are the known variables and the switching angles are the unknown variables. With the dataset generated by GA, an artificial neural network (ANN) is trained to store the solutions without excessive memorymore » storage requirements. This trained ANN then senses the voltage of each cell and produces the switching angles in order to regulate the fundamental at 120 V and eliminate or minimize the low order harmonics while operating in real time.« less

Superiorization with level control

NASA Astrophysics Data System (ADS)

Cegielski, Andrzej; Al-Musallam, Fadhel

2017-04-01

The convex feasibility problem is to find a common point of a finite family of closed convex subsets. In many applications one requires something more, namely finding a common point of closed convex subsets which minimizes a continuous convex function. The latter requirement leads to an application of the superiorization methodology which is actually settled between methods for convex feasibility problem and the convex constrained minimization. Inspired by the superiorization idea we introduce a method which sequentially applies a long-step algorithm for a sequence of convex feasibility problems; the method employs quasi-nonexpansive operators as well as subgradient projections with level control and does not require evaluation of the metric projection. We replace a perturbation of the iterations (applied in the superiorization methodology) by a perturbation of the current level in minimizing the objective function. We consider the method in the Euclidean space in order to guarantee the strong convergence, although the method is well defined in a Hilbert space.

Interface design and human factors considerations for model-based tight glycemic control in critical care.

PubMed

Ward, Logan; Steel, James; Le Compte, Aaron; Evans, Alicia; Tan, Chia-Siong; Penning, Sophie; Shaw, Geoffrey M; Desaive, Thomas; Chase, J Geoffrey

2012-01-01

Tight glycemic control (TGC) has shown benefits but has been difficult to implement. Model-based methods and computerized protocols offer the opportunity to improve TGC quality and compliance. This research presents an interface design to maximize compliance, minimize real and perceived clinical effort, and minimize error based on simple human factors and end user input. The graphical user interface (GUI) design is presented by construction based on a series of simple, short design criteria based on fundamental human factors engineering and includes the use of user feedback and focus groups comprising nursing staff at Christchurch Hospital. The overall design maximizes ease of use and minimizes (unnecessary) interaction and use. It is coupled to a protocol that allows nurse staff to select measurement intervals and thus self-manage workload. The overall GUI design is presented and requires only one data entry point per intervention cycle. The design and main interface are heavily focused on the nurse end users who are the predominant users, while additional detailed and longitudinal data, which are of interest to doctors guiding overall patient care, are available via tabs. This dichotomy of needs and interests based on the end user's immediate focus and goals shows how interfaces must adapt to offer different information to multiple types of users. The interface is designed to minimize real and perceived clinical effort, and ongoing pilot trials have reported high levels of acceptance. The overall design principles, approach, and testing methods are based on fundamental human factors principles designed to reduce user effort and error and are readily generalizable. © 2012 Diabetes Technology Society.

Method for Hot Real-Time Sampling of Gasification Products

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pomeroy, Marc D

The Thermochemical Process Development Unit (TCPDU) at the National Renewable Energy Laboratory (NREL) is a highly instrumented half-ton/day pilot scale plant capable of demonstrating industrially relevant thermochemical technologies from lignocellulosic biomass conversion, including gasification. Gasification creates primarily Syngas (a mixture of Hydrogen and Carbon Monoxide) that can be utilized with synthesis catalysts to form transportation fuels and other valuable chemicals. Biomass derived gasification products are a very complex mixture of chemical components that typically contain Sulfur and Nitrogen species that can act as catalysis poisons for tar reforming and synthesis catalysts. Real-time hot online sampling techniques, such as Molecular Beammore » Mass Spectrometry (MBMS), and Gas Chromatographs with Sulfur and Nitrogen specific detectors can provide real-time analysis providing operational indicators for performance. Sampling typically requires coated sampling lines to minimize trace sulfur interactions with steel surfaces. Other materials used inline have also shown conversion of sulfur species into new components and must be minimized. Sample line Residence time within the sampling lines must also be kept to a minimum to reduce further reaction chemistries. Solids from ash and char contribute to plugging and must be filtered at temperature. Experience at NREL has shown several key factors to consider when designing and installing an analytical sampling system for biomass gasification products. They include minimizing sampling distance, effective filtering as close to source as possible, proper line sizing, proper line materials or coatings, even heating of all components, minimizing pressure drops, and additional filtering or traps after pressure drops.« less

Compact fiber optic gyroscopes for platform stabilization

NASA Astrophysics Data System (ADS)

Dickson, William C.; Yee, Ting K.; Coward, James F.; McClaren, Andrew; Pechner, David A.

2013-09-01

SA Photonics has developed a family of compact Fiber Optic Gyroscopes (FOGs) for platform stabilization applications. The use of short fiber coils enables the high update rates required for stabilization applications but presents challenges to maintain high performance. We are able to match the performance of much larger FOGs by utilizing several innovative technologies. These technologies include source noise reduction to minimize Angular Random Walk (ARW), advanced digital signal processing that minimizes bias drift at high update rates, and advanced passive thermal packaging that minimizes temperature induced bias drift while not significantly affecting size, weight, or power. In addition, SA Photonics has developed unique distributed FOG packaging technologies allowing the FOG electronics and photonics to be packaged remotely from the sensor head or independent axis heads to minimize size, weight, and power at the sensing location(s). The use of these technologies has resulted in high performance, including ARW less than 0.001 deg/rt-hr and bias drift less than 0.004 deg/hr at an update rate of 10 kHz, and total packaged volume less than 30 cu. in. for a 6 degree of freedom FOG-based IMU. Specific applications include optical beam stabilization for LIDAR and LADAR, beam stabilization for long-range free-space optical communication, Optical Inertial Reference Units for HEL stabilization, and Ka band antenna pedestal pointing and stabilization. The high performance of our FOGs also enables their use in traditional navigation and positioning applications. This paper will review the technologies enabling our high-performance compact FOGs, and will provide performance test results.

Interface Design and Human Factors Considerations for Model-Based Tight Glycemic Control in Critical Care

PubMed Central

Ward, Logan; Steel, James; Le Compte, Aaron; Evans, Alicia; Tan, Chia-Siong; Penning, Sophie; Shaw, Geoffrey M; Desaive, Thomas; Chase, J Geoffrey

2012-01-01

Introduction Tight glycemic control (TGC) has shown benefits but has been difficult to implement. Model-based methods and computerized protocols offer the opportunity to improve TGC quality and compliance. This research presents an interface design to maximize compliance, minimize real and perceived clinical effort, and minimize error based on simple human factors and end user input. Method The graphical user interface (GUI) design is presented by construction based on a series of simple, short design criteria based on fundamental human factors engineering and includes the use of user feedback and focus groups comprising nursing staff at Christchurch Hospital. The overall design maximizes ease of use and minimizes (unnecessary) interaction and use. It is coupled to a protocol that allows nurse staff to select measurement intervals and thus self-manage workload. Results The overall GUI design is presented and requires only one data entry point per intervention cycle. The design and main interface are heavily focused on the nurse end users who are the predominant users, while additional detailed and longitudinal data, which are of interest to doctors guiding overall patient care, are available via tabs. This dichotomy of needs and interests based on the end user's immediate focus and goals shows how interfaces must adapt to offer different information to multiple types of users. Conclusions The interface is designed to minimize real and perceived clinical effort, and ongoing pilot trials have reported high levels of acceptance. The overall design principles, approach, and testing methods are based on fundamental human factors principles designed to reduce user effort and error and are readily generalizable. PMID:22401330

Minimally invasive esthetic ridge preservation with growth-factor enhanced bone matrix.

PubMed

Nevins, Marc L; Said, Sherif

2017-12-28

Extraction socket preservation procedures are critical to successful esthetic implant therapy. Conventional surgical approaches are technique sensitive and often result in alteration of the soft tissue architecture, which then requires additional corrective surgical procedures. This case series report presents the ability of flapless surgical techniques combined with a growth factor-enhanced bone matrix to provide esthetic ridge preservation at the time of extraction for compromised sockets. When considering esthetic dental implant therapy, preservation, or further enhancement of the available tissue support at the time of tooth extraction may provide an improved esthetic outcome with reduced postoperative sequelae and decreased treatment duration. Advances in minimally invasive surgical techniques combined with recombinant growth factor technology offer an alternative for bone reconstruction while maintaining the gingival architecture for enhanced esthetic outcome. The combination of freeze-dried bone allograft (FDBA) and rhPDGF-BB (platelet-derived growth factor-BB) provides a growth-factor enhanced matrix to induce bone and soft tissue healing. The use of a growth-factor enhanced matrix is an option for minimally invasive ridge preservation procedures for sites with advanced bone loss. Further studies including randomized clinical trials are needed to better understand the extent and limits of these procedures. The use of minimally invasive techniques with growth factors for esthetic ridge preservation reduces patient morbidity associated with more invasive approaches and increases the predictability for enhanced patient outcomes. By reducing the need for autogenous bone grafts the use of this technology is favorable for patient acceptance and ease of treatment process for esthetic dental implant therapy. © 2017 Wiley Periodicals, Inc.

System for robot-assisted real-time laparoscopic ultrasound elastography

NASA Astrophysics Data System (ADS)

Billings, Seth; Deshmukh, Nishikant; Kang, Hyun Jae; Taylor, Russell; Boctor, Emad M.

2012-02-01

Surgical robots provide many advantages for surgery, including minimal invasiveness, precise motion, high dexterity, and crisp stereovision. One limitation of current robotic procedures, compared to open surgery, is the loss of haptic information for such purposes as palpation, which can be very important in minimally invasive tumor resection. Numerous studies have reported the use of real-time ultrasound elastography, in conjunction with conventional B-mode ultrasound, to differentiate malignant from benign lesions. Several groups (including our own) have reported integration of ultrasound with the da Vinci robot, and ultrasound elastography is a very promising image guidance method for robotassisted procedures that will further enable the role of robots in interventions where precise knowledge of sub-surface anatomical features is crucial. We present a novel robot-assisted real-time ultrasound elastography system for minimally invasive robot-assisted interventions. Our system combines a da Vinci surgical robot with a non-clinical experimental software interface, a robotically articulated laparoscopic ultrasound probe, and our GPU-based elastography system. Elasticity and B-mode ultrasound images are displayed as picture-in-picture overlays in the da Vinci console. Our system minimizes dependence on human performance factors by incorporating computer-assisted motion control that automatically generates the tissue palpation required for elastography imaging, while leaving high-level control in the hands of the user. In addition to ensuring consistent strain imaging, the elastography assistance mode avoids the cognitive burden of tedious manual palpation. Preliminary tests of the system with an elasticity phantom demonstrate the ability to differentiate simulated lesions of varied stiffness and to clearly delineate lesion boundaries.

The influence of wheelchair propulsion technique on upper extremity muscle demand: a simulation study.

PubMed

Rankin, Jeffery W; Kwarciak, Andrew M; Richter, W Mark; Neptune, Richard R

2012-11-01

The majority of manual wheelchair users will experience upper extremity injuries or pain, in part due to the high force requirements, repetitive motion and extreme joint postures associated with wheelchair propulsion. Recent studies have identified cadence, contact angle and peak force as important factors for reducing upper extremity demand during propulsion. However, studies often make comparisons between populations (e.g., able-bodied vs. paraplegic) or do not investigate specific measures of upper extremity demand. The purpose of this study was to use a musculoskeletal model and forward dynamics simulations of wheelchair propulsion to investigate how altering cadence, peak force and contact angle influence individual muscle demand. Forward dynamics simulations of wheelchair propulsion were generated to emulate group-averaged experimental data during four conditions: 1) self-selected propulsion technique, and while 2) minimizing cadence, 3) maximizing contact angle, and 4) minimizing peak force using biofeedback. Simulations were used to determine individual muscle mechanical power and stress as measures of muscle demand. Minimizing peak force and cadence had the lowest muscle power requirements. However, minimizing peak force increased cadence and recovery power, while minimizing cadence increased average muscle stress. Maximizing contact angle increased muscle stress and had the highest muscle power requirements. Minimizing cadence appears to have the most potential for reducing muscle demand and fatigue, which could decrease upper extremity injuries and pain. However, altering any of these variables to extreme values appears to be less effective; instead small to moderate changes may better reduce overall muscle demand. Copyright © 2012 Elsevier Ltd. All rights reserved.

Arc-Second Alignment of International X-Ray Observatory Mirror Segments in a Fixed Structure

NASA Technical Reports Server (NTRS)

Evans, Tyler, C.; Chan, Kai-Wing; Saha, Timo T.

2010-01-01

The optics for the International X-Ray Observatory (IXO) require alignment and integration of about fourteen thousand thin mirror segments to achieve the mission goal of 3.0 square meters of effective area at 1.25 keV with an angular resolution of five arc-seconds. These mirror segments are 0.4 mm thick, and 200 to 400 mm in size, which makes it hard to meet the strict angular resolution requirement of 5 arc-seconds for the telescope. This paper outlines the precise alignment, verification testing, and permanent bonding techniques developed at NASA's Goddard Space Flight Center (GSFC). These techniques are used to overcome the challenge of transferring thin mirror segments from a temporary mount to a fixed structure with arc-second alignment and minimal figure distortion. Recent advances in technology development in addition to the automation of several processes have produced significant results. Recent advances in the mirror fixture process known as the suspension mount has allowed for a mirror to be mounted to a fixture with minimal distortion. Once on the fixture, mirror segments have been aligned to around 5 arc-seconds which is halfway to the goal of 2.5 arc-seconds per mirror segment. This paper will highlight the recent advances in alignment, testing, and permanent bonding techniques as well as the results they have produced.

Optimizing communication satellites payload configuration with exact approaches

NASA Astrophysics Data System (ADS)

Stathakis, Apostolos; Danoy, Grégoire; Bouvry, Pascal; Talbi, El-Ghazali; Morelli, Gianluigi

2015-12-01

The satellite communications market is competitive and rapidly evolving. The payload, which is in charge of applying frequency conversion and amplification to the signals received from Earth before their retransmission, is made of various components. These include reconfigurable switches that permit the re-routing of signals based on market demand or because of some hardware failure. In order to meet modern requirements, the size and the complexity of current communication payloads are increasing significantly. Consequently, the optimal payload configuration, which was previously done manually by the engineers with the use of computerized schematics, is now becoming a difficult and time consuming task. Efficient optimization techniques are therefore required to find the optimal set(s) of switch positions to optimize some operational objective(s). In order to tackle this challenging problem for the satellite industry, this work proposes two Integer Linear Programming (ILP) models. The first one is single-objective and focuses on the minimization of the length of the longest channel path, while the second one is bi-objective and additionally aims at minimizing the number of switch changes in the payload switch matrix. Experiments are conducted on a large set of instances of realistic payload sizes using the CPLEX® solver and two well-known exact multi-objective algorithms. Numerical results demonstrate the efficiency and limitations of the ILP approach on this real-world problem.

Safety and Efficacy of Single Incision Laparoscopic Surgery for Total Extraperitoneal Inguinal Hernia Repair

PubMed Central

2011-01-01

Almost 20 years after the first laparoscopic inguinal hernia repair was performed, single incision laparoscopic surgery (SILS™) is set to revolutionize minimally invasive surgery. However, the loss of triangulation must be overcome before the technique can be popularized. This study reports the first 100 laparoscopic total extraperitoneal hernia repairs using a single incision. The study cohort comprised 68 patients with a mean age of 44 (range, 18 to 83): 36 unilateral and 32 bilateral hernias. Twelve patients also underwent umbilical hernia repair with the Ventralex patch requiring no additional incisions. A 2.5-cm to 3-cm crescentic incision within the confines of the umbilicus was performed. Standard dissecting instruments and 52-cm/5.5-mm/300 laparoscope were used. Operation times were 50 minutes for unilateral and 80 minutes for bilateral. There was one conversion to conventional 3-port laparoscopic repair and none to open surgery. Outpatient surgery was achieved in all (except one). Analgesic requirements were minimal: 8 Dextropropoxyphene tablets (range, 0 to 20). There were no intraoperative or postoperative complications with a high patient satisfaction score. Single-incision laparoscopic hernia repair is safe and efficient simply by modifying dissection techniques (so-called “inline” and “vertical”). Comparable success can be obtained while negating the risks of bowel and vascular injuries from sharp trocars and achieving improved cosmetic results. PMID:21902942

Algorithm-Based Motion Magnification for Video Processing in Urological Laparoscopy.

PubMed

Adams, Fabian; Schoelly, Reto; Schlager, Daniel; Schoenthaler, Martin; Schoeb, Dominik S; Wilhelm, Konrad; Hein, Simon; Wetterauer, Ulrich; Miernik, Arkadiusz

2017-06-01

Minimally invasive surgery is in constant further development and has replaced many conventional operative procedures. If vascular structure movement could be detected during these procedures, it could reduce the risk of vascular injury and conversion to open surgery. The recently proposed motion-amplifying algorithm, Eulerian Video Magnification (EVM), has been shown to substantially enhance minimal object changes in digitally recorded video that is barely perceptible to the human eye. We adapted and examined this technology for use in urological laparoscopy. Video sequences of routine urological laparoscopic interventions were recorded and further processed using spatial decomposition and filtering algorithms. The freely available EVM algorithm was investigated for its usability in real-time processing. In addition, a new image processing technology, the CRS iimotion Motion Magnification (CRSMM) algorithm, was specifically adjusted for endoscopic requirements, applied, and validated by our working group. Using EVM, no significant motion enhancement could be detected without severe impairment of the image resolution, motion, and color presentation. The CRSMM algorithm significantly improved image quality in terms of motion enhancement. In particular, the pulsation of vascular structures could be displayed more accurately than in EVM. Motion magnification image processing technology has the potential for clinical importance as a video optimizing modality in endoscopic and laparoscopic surgery. Barely detectable (micro)movements can be visualized using this noninvasive marker-free method. Despite these optimistic results, the technology requires considerable further technical development and clinical tests.

Physiological processes during winter dormancy and their ecological significance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Havranek, W.M.; Tranquillini, W.

1995-07-01

Lengthy and severe winters require that trees in the forests of boreal and mountain zones undergo winter dormancy. Physiologically, a high resistance to subfreezing temperatures and concomitant dehydration are necessary. To accomplish this dormancy, both physiological and structural changes are needed at the cellular level that require induction by endogenous and photoperiodic control early in autumn. Endogenous rhythmicity promotes cold hardening in early autumn and the persistence of hardiness throughout the winter. Numerous physiological functions are maintained at a reduced level, or become completely inhibited during true winter dormancy. Winter hardiness also includes the capability to minimize water loss effectivelymore » when water uptake is severely impeded or impossible. Anatomical features such as tracheids act to minimize xylem embolism during frequent freeze-thaw cycles, and {open_quotes}crown{close_quotes} tissues enable buds to stay in a dehydrated and, thus, more resistant state during winter. Both these structural features are adaptations that contribute to the dominance of conifers in cold climates. Interestingly, deciduous tree species rather than evergreen conifers dominate in the most severe winter climates, although it is not clear whether limitations during winter, during the summer growth period, or during both are most limiting to conifer tree ecology. Additional work that evaluates the importance of winter and summer growth restriction, and their interaction, is needed before a comprehensive understanding of conifer tree ecophysiology will be possible.« less

Anarchic Yukawas and top partial compositeness: the flavour of a successful marriage

NASA Astrophysics Data System (ADS)

Cacciapaglia, Giacomo; Cai, Haiying; Flacke, Thomas; Lee, Seung J.; Parolini, Alberto; Serôdio, Hugo

2015-06-01

The top quark can be naturally singled out from other fermions in the Standard Model due to its large mass, of the order of the electroweak scale. We follow this reasoning in models of pseudo Nambu Goldstone Boson composite Higgs, which may derive from an underlying confining dynamics. We consider a new class of flavour models, where the top quark obtains its mass via partial compositeness, while the lighter fermions acquire their masses by a deformation of the dynamics generated at a high flavour scale. One interesting feature of such scenario is that it can avoid all the flavour constraints without the need of flavour symmetries, since the flavour scale can be pushed high enough. We show that both flavour conserving and violating constraints can be satisfied with top partial compositeness without invoking any flavour symmetry for the up-type sector, in the case of the minimal SO(5)/SO(4) coset with top partners in the four-plet and singlet of SO(4). In the down-type sector, some degree of alignment is required if all down-type quarks are elementary. We show that taking the bottom quark partially composite provides a dynamical explanation for the hierarchy causing this alignment. We present explicit realisations of this mechanism which do not require to include additional bottom partner fields. Finally, these conclusions are generalised to scenarios with non-minimal cosets and top partners in larger representations.

Minimal-effort planning of active alignment processes for beam-shaping optics

NASA Astrophysics Data System (ADS)

Haag, Sebastian; Schranner, Matthias; Müller, Tobias; Zontar, Daniel; Schlette, Christian; Losch, Daniel; Brecher, Christian; Roßmann, Jürgen

2015-03-01

In science and industry, the alignment of beam-shaping optics is usually a manual procedure. Many industrial applications utilizing beam-shaping optical systems require more scalable production solutions and therefore effort has been invested in research regarding the automation of optics assembly. In previous works, the authors and other researchers have proven the feasibility of automated alignment of beam-shaping optics such as collimation lenses or homogenization optics. Nevertheless, the planning efforts as well as additional knowledge from the fields of automation and control required for such alignment processes are immense. This paper presents a novel approach of planning active alignment processes of beam-shaping optics with the focus of minimizing the planning efforts for active alignment. The approach utilizes optical simulation and the genetic programming paradigm from computer science for automatically extracting features from a simulated data basis with a high correlation coefficient regarding the individual degrees of freedom of alignment. The strategy is capable of finding active alignment strategies that can be executed by an automated assembly system. The paper presents a tool making the algorithm available to end-users and it discusses the results of planning the active alignment of the well-known assembly of a fast-axis collimator. The paper concludes with an outlook on the transferability to other use cases such as application specific intensity distributions which will benefit from reduced planning efforts.

Application of quadratic optimization to supersonic inlet control.

NASA Technical Reports Server (NTRS)

Lehtinen, B.; Zeller, J. R.

1972-01-01

This paper describes the application of linear stochastic optimal control theory to the design of the control system for the air intake, the inlet, of a supersonic air-breathing propulsion system. The controls must maintain a stable inlet shock position in the presence of random airflow disturbances and prevent inlet unstart. Two different linear time invariant controllers are developed. One is designed to minimize a nonquadratic index, the expected frequency of inlet unstart, and the other is designed to minimize the mean square value of inlet shock motion. The quadratic equivalence principle is used to obtain a linear controller that minimizes the nonquadratic index. The two controllers are compared on the basis of unstart prevention, control effort requirements, and frequency response. It is concluded that while controls designed to minimize unstarts are desirable in that the index minimized is physically meaningful, computation time required is longer than for the minimum mean square shock position approach. The simpler minimum mean square shock position solution produced expected unstart frequency values which were not significantly larger than those of the nonquadratic solution.

Chance-constrained multi-objective optimization of groundwater remediation design at DNAPLs-contaminated sites using a multi-algorithm genetically adaptive method

NASA Astrophysics Data System (ADS)

Ouyang, Qi; Lu, Wenxi; Hou, Zeyu; Zhang, Yu; Li, Shuai; Luo, Jiannan

2017-05-01

In this paper, a multi-algorithm genetically adaptive multi-objective (AMALGAM) method is proposed as a multi-objective optimization solver. It was implemented in the multi-objective optimization of a groundwater remediation design at sites contaminated by dense non-aqueous phase liquids. In this study, there were two objectives: minimization of the total remediation cost, and minimization of the remediation time. A non-dominated sorting genetic algorithm II (NSGA-II) was adopted to compare with the proposed method. For efficiency, the time-consuming surfactant-enhanced aquifer remediation simulation model was replaced by a surrogate model constructed by a multi-gene genetic programming (MGGP) technique. Similarly, two other surrogate modeling methods-support vector regression (SVR) and Kriging (KRG)-were employed to make comparisons with MGGP. In addition, the surrogate-modeling uncertainty was incorporated in the optimization model by chance-constrained programming (CCP). The results showed that, for the problem considered in this study, (1) the solutions obtained by AMALGAM incurred less remediation cost and required less time than those of NSGA-II, indicating that AMALGAM outperformed NSGA-II. It was additionally shown that (2) the MGGP surrogate model was more accurate than SVR and KRG; and (3) the remediation cost and time increased with the confidence level, which can enable decision makers to make a suitable choice by considering the given budget, remediation time, and reliability.

Input Shaping to Reduce Solar Array Structural Vibrations

NASA Technical Reports Server (NTRS)

Doherty, Michael J.; Tolson, Robert J.

1998-01-01

Structural vibrations induced by actuators can be minimized using input shaping. Input shaping is a feedforward method in which actuator commands are convolved with shaping functions to yield a shaped set of commands. These commands are designed to perform the maneuver while minimizing the residual structural vibration. In this report, input shaping is extended to stepper motor actuators. As a demonstration, an input-shaping technique based on pole-zero cancellation was used to modify the Solar Array Drive Assembly (SADA) actuator commands for the Lewis satellite. A series of impulses were calculated as the ideal SADA output for vibration control. These impulses were then discretized for use by the SADA stepper motor actuator and simulated actuator outputs were used to calculate the structural response. The effectiveness of input shaping is limited by the accuracy of the knowledge of the modal frequencies. Assuming perfect knowledge resulted in significant vibration reduction. Errors of 10% in the modal frequencies caused notably higher levels of vibration. Controller robustness was improved by incorporating additional zeros in the shaping function. The additional zeros did not require increased performance from the actuator. Despite the identification errors, the resulting feedforward controller reduced residual vibrations to the level of the exactly modeled input shaper and well below the baseline cases. These results could be easily applied to many other vibration-sensitive applications involving stepper motor actuators.

Recent Updates in the Endoscopic Diagnosis of Barrett's Oesophagus.

PubMed

Sharma, Neel; Ho, Khek Yu

2016-10-01

Barrett's oesophagus (BO) is a premalignant condition associated with the development of oesophageal adenocarcinoma (OAC). Despite the low risk of progression per annum, OAC is associated with significant morbidity and mortality, with an estimated 5-year survival of 10%. Furthermore, the incidence of OAC continues to rise globally. Therefore, it is imperative to detect the premalignant phase of BO and follow up such patients accordingly. The mainstay diagnosis of BO is endoscopy and biopsy sampling. However, limitations with white light endoscopy (WLE) and undertaking biopsies have shifted the current focus towards real-time image analysis. Utilization of additional tools such as chromoendoscopy, narrow-band imaging (NBI), confocal laser endomicroscopy (CLE), and optical coherence tomography (OCT) are proving beneficial. Furthermore, it is also becoming more apparent that often these tools are utilized by experts in the field. Therefore, for the non-expert, training in these systems is key. Currently as yet, the methodologies used for training optimization require further inquiry. (1) Real-time imaging can serve to minimize excess biopsies. (2) Tools such as chromoendoscopy, NBI, CLE, and OCT can help to compliment WLE. WLE is associated with limited sensitivity. Biopsy sampling is cost-ineffective and associated with sampling error. Hence, from a practical perspective, endoscopists should aim to utilize additional tools to help in real-time image interpretation and minimize an overreliance on histology.

Recent Updates in the Endoscopic Diagnosis of Barrett's Oesophagus

PubMed Central

Sharma, Neel; Ho, Khek Yu

2016-01-01

Background Barrett's oesophagus (BO) is a premalignant condition associated with the development of oesophageal adenocarcinoma (OAC). Despite the low risk of progression per annum, OAC is associated with significant morbidity and mortality, with an estimated 5-year survival of 10%. Furthermore, the incidence of OAC continues to rise globally. Therefore, it is imperative to detect the premalignant phase of BO and follow up such patients accordingly. Summary The mainstay diagnosis of BO is endoscopy and biopsy sampling. However, limitations with white light endoscopy (WLE) and undertaking biopsies have shifted the current focus towards real-time image analysis. Utilization of additional tools such as chromoendoscopy, narrow-band imaging (NBI), confocal laser endomicroscopy (CLE), and optical coherence tomography (OCT) are proving beneficial. Furthermore, it is also becoming more apparent that often these tools are utilized by experts in the field. Therefore, for the non-expert, training in these systems is key. Currently as yet, the methodologies used for training optimization require further inquiry. Key Message (1) Real-time imaging can serve to minimize excess biopsies. (2) Tools such as chromoendoscopy, NBI, CLE, and OCT can help to compliment WLE. Practical Implications WLE is associated with limited sensitivity. Biopsy sampling is cost-ineffective and associated with sampling error. Hence, from a practical perspective, endoscopists should aim to utilize additional tools to help in real-time image interpretation and minimize an overreliance on histology. PMID:27904863

The Liquid Nitrogen System for Chamber A: A Change from Original Forced Flow Design to a Natural Flow (Thermo Siphon) System

NASA Technical Reports Server (NTRS)

Homan, Jonathan; Montz, Michael; Sidi-Yekhlef, Ahmed; Ganni, Venkatarao (Rao); Knudsen, Peter; Garcia, Sam; Linza, Robert; Meagher, Daniel; Lauterbauch, John

2008-01-01

NASA Johnson Space Center (JSC) in Houston is currently supplementing its 20K helium refrigeration system to meet the new requirements for testing the James Web Space Telescope in the environmental control Chamber-A (65 dia x 120 high) in Building 32. The new system is required to meet the various operating modes which include a high 20K heat load, a required temperature stability at the load, rapid (but controlled) cool down and warm up and bake out of the chamber. This paper will present the proposed modifications to the existing helium system(s) to incorporate the new requirements and the integration of the new helium refrigerator with the existing two 3.5KW 20K helium refrigerators. In addition, the floating pressure process control philosophy to achieve high efficiency over the operating range (40% to 100% of the refrigeration system capacity), and the required temperature stability of +/- 0.25 K at the load will be discussed. The refrigeration systems ability to naturally seek the operating conditions under various loads and thus minimizing operator involvement and the over all improvements to the system operability and the reliability will be explained.

Open-type ferry safety system design for using LNG fuel

NASA Astrophysics Data System (ADS)

Pagonis, D. N.; Livanos, G.; Theotokatos, G.; Peppa, S.; Themelis, N.

2016-12-01

In this feasibility study, we investigate the viability of using Liquefied Natural Gas (LNG) fuel in an open type Ro-Ro passenger ferry and the associated potential challenges with regard to the vessel safety systems. We recommend an appropriate methodology for converting existing ships to run on LNG fuel, discuss all the necessary modifications to the ship's safety systems, and also evaluate the relevant ship evacuation procedures. We outline the basic requirements with which the ship already complies for each safety system and analyze the additional restrictions that must be taken into consideration for the use of LNG fuel. Appropriate actions are recommended. Furthermore, we carry out a hazard identification study. Overall, we clearly demonstrate the technical feasibility of the investigated scenario. Minimal modifications to the ship's safety systems are required to comply with existing safety rules for this specific type of ship.

Auto identification technology and its impact on patient safety in the Operating Room of the Future.

PubMed

Egan, Marie T; Sandberg, Warren S

2007-03-01

Automatic identification technologies, such as bar coding and radio frequency identification, are ubiquitous in everyday life but virtually nonexistent in the operating room. User expectations, based on everyday experience with automatic identification technologies, have generated much anticipation that these systems will improve readiness, workflow, and safety in the operating room, with minimal training requirements. We report, in narrative form, a multi-year experience with various automatic identification technologies in the Operating Room of the Future Project at Massachusetts General Hospital. In each case, the additional human labor required to make these ;labor-saving' technologies function in the medical environment has proved to be their undoing. We conclude that while automatic identification technologies show promise, significant barriers to realizing their potential still exist. Nevertheless, overcoming these obstacles is necessary if the vision of an operating room of the future in which all processes are monitored, controlled, and optimized is to be achieved.

Computation of Molecular Spectra on a Quantum Processor with an Error-Resilient Algorithm

DOE PAGES

Colless, J. I.; Ramasesh, V. V.; Dahlen, D.; ...

2018-02-12

Harnessing the full power of nascent quantum processors requires the efficient management of a limited number of quantum bits with finite coherent lifetimes. Hybrid algorithms, such as the variational quantum eigensolver (VQE), leverage classical resources to reduce the required number of quantum gates. Experimental demonstrations of VQE have resulted in calculation of Hamiltonian ground states, and a new theoretical approach based on a quantum subspace expansion (QSE) has outlined a procedure for determining excited states that are central to dynamical processes. Here, we use a superconducting-qubit-based processor to apply the QSE approach to the H 2 molecule, extracting both groundmore » and excited states without the need for auxiliary qubits or additional minimization. Further, we show that this extended protocol can mitigate the effects of incoherent errors, potentially enabling larger-scale quantum simulations without the need for complex error-correction techniques.« less

Computation of Molecular Spectra on a Quantum Processor with an Error-Resilient Algorithm

NASA Astrophysics Data System (ADS)

Colless, J. I.; Ramasesh, V. V.; Dahlen, D.; Blok, M. S.; Kimchi-Schwartz, M. E.; McClean, J. R.; Carter, J.; de Jong, W. A.; Siddiqi, I.

2018-02-01

Harnessing the full power of nascent quantum processors requires the efficient management of a limited number of quantum bits with finite coherent lifetimes. Hybrid algorithms, such as the variational quantum eigensolver (VQE), leverage classical resources to reduce the required number of quantum gates. Experimental demonstrations of VQE have resulted in calculation of Hamiltonian ground states, and a new theoretical approach based on a quantum subspace expansion (QSE) has outlined a procedure for determining excited states that are central to dynamical processes. We use a superconducting-qubit-based processor to apply the QSE approach to the H2 molecule, extracting both ground and excited states without the need for auxiliary qubits or additional minimization. Further, we show that this extended protocol can mitigate the effects of incoherent errors, potentially enabling larger-scale quantum simulations without the need for complex error-correction techniques.

A Primer for Telemetry Interfacing in Accordance with NASA Standards Using Low Cost FPGAs

NASA Astrophysics Data System (ADS)

McCoy, Jake; Schultz, Ted; Tutt, James; Rogers, Thomas; Miles, Drew; McEntaffer, Randall

2016-03-01

Photon counting detector systems on sounding rocket payloads often require interfacing asynchronous outputs with a synchronously clocked telemetry (TM) stream. Though this can be handled with an on-board computer, there are several low cost alternatives including custom hardware, microcontrollers and field-programmable gate arrays (FPGAs). This paper outlines how a TM interface (TMIF) for detectors on a sounding rocket with asynchronous parallel digital output can be implemented using low cost FPGAs and minimal custom hardware. Low power consumption and high speed FPGAs are available as commercial off-the-shelf (COTS) products and can be used to develop the main component of the TMIF. Then, only a small amount of additional hardware is required for signal buffering and level translating. This paper also discusses how this system can be tested with a simulated TM chain in the small laboratory setting using FPGAs and COTS specialized data acquisition products.

[Human capital vs. manpower: fostering a greater global perspective within the nursing profession in Taiwan].

PubMed

Chen, Li-Yen; Chou, Shieu-Ming

2014-04-01

Nursing today is an occupation greatly influenced and shaped by global standards and internationally recognized standard practices and requirements. Therefore, cultivating nursing capital and ensuring nursing manpower requires an international perspective. Nursing migration is currently a popular approach used by many developed countries to address domestic shortfalls in nursing manpower. These international medical services have had a great impact on nursing education. Being able to communicate in English and to adapt transculturally have thus become increasingly important. Ability to communicate well in English is one effective way both to minimize nurse-patient misunderstandings and to increase the quality of care available to foreign patients. In addition, transcultural communication underscores the value of respecting cultural diversity. Fostering and enhancing these abilities will enhance and expand the role of Taiwanese nurses in the professional global movement and increase their contributions to the internal medical community.

An Anomalous External Force on the MAP Spacecraft

NASA Technical Reports Server (NTRS)

Starin, Scott R.; Bay, P. Michael; Wollack, Edward J.; Fink, Dale R.; Ward, David K.; ODonnell, James R., Jr.; Bauer, Frank H. (Technical Monitor)

2002-01-01

A common theme in discussions of the Microwave Anisotropy Probe (MAP) is the attainment of mission goals for minimal cost. One area of cost savings was a reduction in the fuel budget required. To reach orbit around the L2 notation point of the Earth-Sun system, the MAP spacecraft was guided very close to the Moon, allowing a gravity-assisted trajectory out to L2. In order to property time the lunar swing-by, MAP followed a trajectory of three-and-a-half highly elliptical phasing loops. At each perigee of this trajectory MAP executed a thruster maneuver to increase orbit velocity; maneuvers were required at one or both clothe first two perigees (called P1 and P2) and at the third and final perigee (P-final). The preference was for successful maneuvers at all three perigees because this scheme provided a small, additional fuel savings.

Computation of Molecular Spectra on a Quantum Processor with an Error-Resilient Algorithm

DOE Office of Scientific and Technical Information (OSTI.GOV)

Colless, J. I.; Ramasesh, V. V.; Dahlen, D.

Harnessing the full power of nascent quantum processors requires the efficient management of a limited number of quantum bits with finite coherent lifetimes. Hybrid algorithms, such as the variational quantum eigensolver (VQE), leverage classical resources to reduce the required number of quantum gates. Experimental demonstrations of VQE have resulted in calculation of Hamiltonian ground states, and a new theoretical approach based on a quantum subspace expansion (QSE) has outlined a procedure for determining excited states that are central to dynamical processes. Here, we use a superconducting-qubit-based processor to apply the QSE approach to the H 2 molecule, extracting both groundmore » and excited states without the need for auxiliary qubits or additional minimization. Further, we show that this extended protocol can mitigate the effects of incoherent errors, potentially enabling larger-scale quantum simulations without the need for complex error-correction techniques.« less

Workload assignment with training, hiring and firing

NASA Astrophysics Data System (ADS)

Eiselt, H. A.; Marianov, V.

2008-11-01

This article discusses a workload allocation model in which tasks are matched to employees on the basis of a multi-dimensional skill measure. The main idea is to match positions and tasks to available and potential positions so as to minimize the differences in individuals' abilities and skill requirements. In addition to allocating existing personnel to positions, it is also possible to fire employees and hire new employees. The objectives of the mixed-integer optimization model include different types of costs and the proximity of an individual's capabilities to a task's ability requirements. A number of policies are formulated that allow different combinations of retraining of employees, as well as hiring and firing. These policies are applied to a real-life example that is solved by means of the constraint method. A variety of sensitivity analyses demonstrate the usefulness of the approach as a decision aid.

Functional Role of Extranucleosomal DNA and the Entry Site of the Nucleosome in Chromatin Remodeling by ISW2

PubMed Central

Zofall, Martin; Persinger, Jim; Bartholomew, Blaine

2004-01-01

A minimal amount of extranucleosomal DNA was required for nucleosome mobilization by ISW2 as shown by using a photochemical histone mapping approach to analyze nucleosome movement on a set of nucleosomes with varied lengths of extranucleosomal DNA. ISW2 was ineffective in repositioning or mobilizing nucleosomes with ≤20 bp of extranucleosomal DNA. In addition, ISW2 was able to slide nucleosomes to within only 10 to 13 bp of the edge of DNA fragments. The nucleosome mobilization was promoted by extranucleosomal single-stranded DNA with modest strand preference. Gaps (10 bp) just inside the nucleosome and in the extranucleosomal DNA showed that the transfer of torsional strain (twist) into the nucleosomal DNA region was not required for mobilizing nucleosomes. However, indications are that the extranucleosomal DNA immediately adjacent to the nucleosome has an important role in the initial stage of nucleosome movement by ISW2. PMID:15509805

Resolving task rule incongruence during task switching by competitor rule suppression.

PubMed

Meiran, Nachshon; Hsieh, Shulan; Dimov, Eduard

2010-07-01

Task switching requires maintaining readiness to execute any task of a given set of tasks. However, when tasks switch, the readiness to execute the now-irrelevant task generates interference, as seen in the task rule incongruence effect. Overcoming such interference requires fine-tuned inhibition that impairs task readiness only minimally. In an experiment involving 2 object classification tasks and 2 location classification tasks, the authors show that irrelevant task rules that generate response conflicts are inhibited. This competitor rule suppression (CRS) is seen in response slowing in subsequent trials, when the competing rules become relevant. CRS is shown to operate on specific rules without affecting similar rules. CRS and backward inhibition, which is another inhibitory phenomenon, produced additive effects on reaction time, suggesting their mutual independence. Implications for current formal theories of task switching as well as for conflict monitoring theories are discussed. (c) 2010 APA, all rights reserved

Environmental Control and Life Support (ECLS) Integrated Roadmap Development

NASA Technical Reports Server (NTRS)

Metcalf, Jordan L.; Carrasquillo, Robyn; Bagdigian, Bob; Peterson, Laurie

2011-01-01

This white paper documents a roadmap for development of Environmental Control and Life Support (ECLS) Systems (ECLSS) capabilities required to enable beyond-Low Earth Orbit (LEO) Exploration missions. In many cases, the execution of this Exploration-based roadmap will directly benefit International Space Station (ISS) operational capability by resolving known issues and/or improving overall system reliability. In addition, many of the resulting products will be applicable across multiple Exploration elements such as Multi-Purpose Crew Vehicle (MPCV), Multi-Mission Space Exploration Vehicle (MMSEV), Deep Space Habitat (DSH), and Landers. Within the ECLS community, this white paper will be a unifying tool that will improve coordination of resources, common hardware, and technologies. It will help to align efforts to focus on the highest priority needs that will produce life support systems for future human exploration missions that will simply run in the background, requiring minimal crew interaction.

The HIP1 initiator element plays a role in determining the in vitro requirement of the dihydrofolate reductase gene promoter for the C-terminal domain of RNA polymerase II.

PubMed

Buermeyer, A B; Thompson, N E; Strasheim, L A; Burgess, R R; Farnham, P J

1992-05-01

We examined the ability of purified RNA polymerase (RNAP) II lacking the carboxy-terminal heptapeptide repeat domain (CTD), called RNAP IIB, to transcribe a variety of promoters in HeLa extracts in which endogenous RNAP II activity was inhibited with anti-CTD monoclonal antibodies. Not all promoters were efficiently transcribed by RNAP IIB, and transcription did not correlate with the in vitro strength of the promoter or with the presence of a consensus TATA box. This was best illustrated by the GC-rich, non-TATA box promoters of the bidirectional dihydrofolate reductase (DHFR)-REP-encoding locus. Whereas the REP promoter was transcribed by RNAP IIB, the DHFR promoter remained inactive after addition of RNAP IIB to the antibody-inhibited reactions. However, both promoters were efficiently transcribed when purified RNAP with an intact CTD was added. We analyzed a series of promoter deletions to identify which cis elements determine the requirement for the CTD of RNAP II. All of the promoter deletions of both DHFR and REP retained the characteristics of their respective full-length promoters, suggesting that the information necessary to specify the requirement for the CTD is contained within approximately 65 bp near the initiation site. Furthermore, a synthetic minimal promoter of DHFR, consisting of a single binding site for Sp1 and a binding site for the HIP1 initiator cloned into a bacterial vector sequence, required RNAP II with an intact CTD for activity in vitro. Since the synthetic minimal promoter of DHFR and the smallest REP promoter deletion are both activated by Sp1, the differential response in this assay does not result from upstream activators. However, the sequences around the start sites of DHFR and REP are not similar and our data suggest that they bind different proteins. Therefore, we propose that specific initiator elements are important for determination of the requirement of some promoters for the CTD.

COMBINATION THERAPY WITH FLUOXETINE AND ALPRAZOLAM TO CONTROL ANXIETY IN A HAND-REARED SNOW LEOPARD (UNCIA UNCIA).

PubMed

Holman, Holly J

2016-09-01

A captive hand-reared adult male snow leopard ( Uncia uncia ) was treated for anxiety associated with taunting from visitors, the presence of large crowds, and introduction to a female for breeding. Behaviors included shaking, chewing on tail, panting, panicking, and bouncing off the viewing glass, pacing, and avoidance of the female. Combination therapy of oral fluoxetine and alprazolam were administered initially to minimize anxious behaviors while the fluoxetine achieved therapeutic levels. The alprazolam was tapered completely and was only used episodically on two occasions. Although a palatability issue with alprazolam initially prevented consistent dosing, anxious behavior was eliminated and successful breeding behavior was achieved for the first time. After 44 mo of therapy, there have been no anxious behaviors requiring additional medications, two additional breeding behaviors observed, and no evidence of adverse side effects with long-term use.

Recent Advances for the Detection of Ochratoxin A.

PubMed

Ha, Tai Hwan

2015-12-04

Ochratoxin A (OTA) is one of the mycotoxins secreted by Aspersillus and Penicillium that can easily colonize various grains like coffee, peanut, rice, and maize. Since OTA is a chemically stable compound that can endure the physicochemical conditions of modern food processing, additional research efforts have been devoted to develop sensitive and cost-effective surveillance solutions. Although traditional chromatographic and immunoassays appear to be mature enough to attain sensitivity up to the regulation levels, alternative detection schemes are still being enthusiastically pursued in an attempt to meet the requirements of rapid and cost-effective detections. Herein, this review presents recent progresses in OTA detections with minimal instrumental usage, which have been facilitated by the development of OTA aptamers and by the innovations in functional nanomaterials. In addition to the introduction of aptamer-based OTA detection techniques, OTA-specific detection principles are also presented, which exclusively take advantage of the unique chemical structure and related physicochemical characteristics.

Acetone facilitated DNA sampling from electrical tapes improves DNA recovery and enables latent fingerprints development.

PubMed

Feine, Ilan; Shpitzen, Moshe; Geller, Boris; Salmon, Eran; Peleg, Tsach; Roth, Jonathan; Gafny, Ron

2017-07-01

Electrical tapes (ETs) are a common component of improvised explosive devices (IEDs) used by terrorists or criminal organizations and represent a valuable forensic resource for DNA and latent fingerprints recovery. However, DNA recovery rates are typically low and usually below the minimal amount required for amplification. In addition, most DNA extraction methods are destructive and do not allow further latent fingerprints development. In the present study a cell culture based touch DNA model was used to demonstrate a two-step acetone-water DNA recovery protocol from ETs. This protocol involves only the adhesive side of the ET and increases DNA recovery rates by up to 70%. In addition, we demonstrated partially successful latent fingerprints development from the non-sticky side of the ETs. Taken together, this protocol maximizes the forensic examination of ETs and is recommended for routine casework processing. Copyright © 2017 Elsevier B.V. All rights reserved.

Reliability of the individual components of the Canadian Armed Forces Physical Employment Standard.

PubMed

Stockbrugger, Barry G; Reilly, Tara J; Blacklock, Rachel E; Gagnon, Patrick J

2018-01-29

This investigation recruited 24 participants from both the Canadian Armed Forces (CAF) and civilian populations to complete 4 separate trials at "best effort" of each of the 4 components in the CAF Physical Employment Standard named the FORCE Evaluation: Fitness for Operational Requirements of CAF Employment. Analyses were performed to examine the level of variability and reliability within each component. The results demonstrate that candidates should be provided with at least 1 retest if they have recently completed at least 2 previous best effort attempts as per the protocol. In addition, the minimal detectable difference is given for each of the 4 components in seconds which identifies the threshold for subsequent action, either retest or remedial training, for those unable to meet the minimum standard. These results will educate the delivery of this employment standard, function as a method of accommodation, in addition to providing direction for physical training programs.

Design and Testing of Demonstration Unit for Maintaining Zero Cryogenic Propellant Boiloff

NASA Technical Reports Server (NTRS)

Dean, W. G.

2000-01-01

Launching of cryogenic propellants into earth orbit and beyond is very expensive. Each additional pound of payload delivered to low earth orbit requires approximately 35 pounds of additional weight at liftoff. There is therefore a critical need to minimize boiloff in spacecraft long term missions/systems. Various methods have been used to date, including superinsulation and thermodynamic vents to reduce boiloff. A system was designed and tested as described herein that will totally eliminate boiloff. This system is based on a closed-loop, two-stage pulse tube refrigerator with a net refrigeration of four watts at 15k for the recovery of hydrogen propellant. It is designed to operate at 30 Hz which is an order of magnitude higher than other typical pulse tube refrigerators. This high frequency allows the use of a much smaller, lighter weight compressor, This paper describes the system design, fabrication and test results.

Microlaparoscopic technique for partial salpingectomy using bipolar electrocoagulation.

PubMed

Siegle, J C; Cartmell, L W; Rayburn, W F

2001-07-01

To describe a technique of performing a partial salpingectomy using a small-diameter (2-mm) laparoscope and bipolar electrocoagulation. Sixty consecutive women desiring permanent sterilization underwent laparoscopic partial salpingectomy using a 2-mm transumbilical laparoscope and secondary midline sites suprapubically and midway above the pubis. A midportion of the tube was coagulated using Kleppinger forceps, transected with scissors and removed using grasping forceps. Additional time to remove both coagulated tubal segments averaged 4 minutes (range, 3-10). Each segment (mean, 1.5 cm; range, 0.9-2.4 cm) was confirmed in the operating room, then histologically. The transected tubal edges were separated with no thermal injury to nearby structures and with no mesosalpingeal hemorrhage. No cases required conversion from microlaparoscopy to a traditional method, and recovery time was not prolonged. The puncture sites healed well without sutures. Successful removal of electrocoagulated tubal segments with histologic confirmation was undertaken microlaparoscopically, with minimal additional operative time.

Dry-grind processing using amylase corn and superior yeast to reduce the exogenous enzyme requirements in bioethanol production.

PubMed

Kumar, Deepak; Singh, Vijay

2016-01-01

Conventional corn dry-grind ethanol production process requires exogenous alpha and glucoamylases enzymes to breakdown starch into glucose, which is fermented to ethanol by yeast. This study evaluates the potential use of new genetically engineered corn and yeast, which can eliminate or minimize the use of these external enzymes, improve the economics and process efficiencies, and simplify the process. An approach of in situ ethanol removal during fermentation was also investigated for its potential to improve the efficiency of high-solid fermentation, which can significantly reduce the downstream ethanol and co-product recovery cost. The fermentation of amylase corn (producing endogenous α-amylase) using conventional yeast and no addition of exogenous α-amylase resulted in ethanol concentration of 4.1 % higher compared to control treatment (conventional corn using exogenous α-amylase). Conventional corn processed with exogenous α-amylase and superior yeast (producing glucoamylase or GA) with no exogenous glucoamylase addition resulted in ethanol concentration similar to control treatment (conventional yeast with exogenous glucoamylase addition). Combination of amylase corn and superior yeast required only 25 % of recommended glucoamylase dose to complete fermentation and achieve ethanol concentration and yield similar to control treatment (conventional corn with exogenous α-amylase, conventional yeast with exogenous glucoamylase). Use of superior yeast with 50 % GA addition resulted in similar increases in yield for conventional or amylase corn of approximately 7 % compared to that of control treatment. Combination of amylase corn, superior yeast, and in situ ethanol removal resulted in a process that allowed complete fermentation of 40 % slurry solids with only 50 % of exogenous GA enzyme requirements and 64.6 % higher ethanol yield compared to that of conventional process. Use of amylase corn and superior yeast in the dry-grind processing industry can reduce the total external enzyme usage by more than 80 %, and combining their use with in situ removal of ethanol during fermentation allows efficient high-solid fermentation.

Advanced Process Possibilities in Friction Crush Welding of Aluminum, Steel, and Copper by Using an Additional Wire

NASA Astrophysics Data System (ADS)

Besler, Florian A.; Grant, Richard J.; Schindele, Paul; Stegmüller, Michael J. R.

2017-12-01

Joining sheet metal can be problematic using traditional friction welding techniques. Friction crush welding (FCW) offers a high speed process which requires a simple edge preparation and can be applied to out-of-plane geometries. In this work, an implementation of FCW was employed using an additional wire to weld sheets of EN AW5754 H22, DC01, and Cu-DHP. The joint is formed by bringing together two sheet metal parts, introducing a wire into the weld zone and employing a rotating disk which is subject to an external force. The requirements of the welding preparation and the fundamental process variables are shown. Thermal measurements were taken which give evidence about the maximum temperature in the welding center and the temperature in the periphery of the sheet metals being joined. The high welding speed along with a relatively low heat input results in a minimal distortion of the sheet metal and marginal metallurgical changes in the parent material. In the steel specimens, this FCW implementation produces a fine grain microstructure, enhancing mechanical properties in the region of the weld. Aluminum and copper produced mean bond strengths of 77 and 69 pct to that of the parent material, respectively, whilst the steel demonstrated a strength of 98 pct. Using a wire offers the opportunity to use a higher-alloyed additional material and to precisely adjust the additional material volume appropriate for a given material alignment and thickness.

An Overview on Prenatal Screening for Chromosomal Aberrations.

PubMed

Hixson, Lucas; Goel, Srishti; Schuber, Paul; Faltas, Vanessa; Lee, Jessica; Narayakkadan, Anjali; Leung, Ho; Osborne, Jim

2015-10-01

This article is a review of current and emerging methods used for prenatal detection of chromosomal aneuploidies. Chromosomal anomalies in the developing fetus can occur in any pregnancy and lead to death prior to or shortly after birth or to costly lifelong disabilities. Early detection of fetal chromosomal aneuploidies, an atypical number of certain chromosomes, can help parents evaluate their pregnancy options. Current diagnostic methods include maternal serum sampling or nuchal translucency testing, which are minimally invasive diagnostics, but lack sensitivity and specificity. The gold standard, karyotyping, requires amniocentesis or chorionic villus sampling, which are highly invasive and can cause abortions. In addition, many of these methods have long turnaround times, which can cause anxiety in mothers. Next-generation sequencing of fetal DNA in maternal blood enables minimally invasive, sensitive, and reasonably rapid analysis of fetal chromosomal anomalies and can be of clinical utility to parents. This review covers traditional methods and next-generation sequencing techniques for diagnosing aneuploidies in terms of clinical utility, technological characteristics, and market potential. © 2015 Society for Laboratory Automation and Screening.

Optimal error functional for parameter identification in anisotropic finite strain elasto-plasticity

NASA Astrophysics Data System (ADS)

Shutov, A. V.; Kaygorodtseva, A. A.; Dranishnikov, N. S.

2017-10-01

A problem of parameter identification for a model of finite strain elasto-plasticity is discussed. The utilized phenomenological material model accounts for nonlinear isotropic and kinematic hardening; the model kinematics is described by a nested multiplicative split of the deformation gradient. A hierarchy of optimization problems is considered. First, following the standard procedure, the material parameters are identified through minimization of a certain least square error functional. Next, the focus is placed on finding optimal weighting coefficients which enter the error functional. Toward that end, a stochastic noise with systematic and non-systematic components is introduced to the available measurement results; a superordinate optimization problem seeks to minimize the sensitivity of the resulting material parameters to the introduced noise. The advantage of this approach is that no additional experiments are required; it also provides an insight into the robustness of the identification procedure. As an example, experimental data for the steel 42CrMo4 are considered and a set of weighting coefficients is found, which is optimal in a certain class.

GUIdock-VNC: using a graphical desktop sharing system to provide a browser-based interface for containerized software

PubMed Central

Mittal, Varun; Hung, Ling-Hong; Keswani, Jayant; Kristiyanto, Daniel; Lee, Sung Bong

2017-01-01

Abstract Background: Software container technology such as Docker can be used to package and distribute bioinformatics workflows consisting of multiple software implementations and dependencies. However, Docker is a command line–based tool, and many bioinformatics pipelines consist of components that require a graphical user interface. Results: We present a container tool called GUIdock-VNC that uses a graphical desktop sharing system to provide a browser-based interface for containerized software. GUIdock-VNC uses the Virtual Network Computing protocol to render the graphics within most commonly used browsers. We also present a minimal image builder that can add our proposed graphical desktop sharing system to any Docker packages, with the end result that any Docker packages can be run using a graphical desktop within a browser. In addition, GUIdock-VNC uses the Oauth2 authentication protocols when deployed on the cloud. Conclusions: As a proof-of-concept, we demonstrated the utility of GUIdock-noVNC in gene network inference. We benchmarked our container implementation on various operating systems and showed that our solution creates minimal overhead. PMID:28327936

STME Hydrogen Mixer Study

NASA Technical Reports Server (NTRS)

Blumenthal, Rob; Kim, Dongmoon; Bache, George

1992-01-01

The hydrogen mixer for the Space Transportation Main Engine is used to mix cold hydrogen bypass flow with warm hydrogen coolant chamber gas, which is then fed to the injectors. It is very important to have a uniform fuel temperature at the injectors in order to minimize mixture ratio problems due to the fuel density variations. In addition, the fuel at the injector has certain total pressure requirements. In order to achieve these objectives, the hydrogen mixer must provide a thoroughly mixed fluid with a minimum pressure loss. The AEROVISC computational fluid dynamics (CFD) code was used to analyze the STME hydrogen mixer, and proved to be an effective tool in optimizing the mixer design. AEROVISC, which solves the Reynolds Stress-Averaged Navier-Stokes equations in primitive variable form, was used to assess the effectiveness of different mixer designs. Through a parametric study of mixer design variables, an optimal design was selected which minimized mixed fuel temperature variation and fuel mixer pressure loss. The use of CFD in the design process of the STME hydrogen mixer was effective in achieving an optimal mixer design while reducing the amount of hardware testing.

Nutritional modulation of health, egg quality and environmental pollution of the layers.

PubMed

Wang, Jing; Yue, Hongyuan; Wu, Shugeng; Zhang, Haijun; Qi, Guanghai

2017-06-01

World egg production and consumption have been increasing for the past decades. Traditional strategies in poultry nutrition have made vital contributions to this great growth in quantity. However, current global issues should be considered in modern egg production such as growing populations and food security, food safety and quality, limited resources and environmental problems. The development of knowledge of poultry nutrition and modern biotechnology provides novel nutritional approaches to closely fit the requirement of pullets and laying hens, which will consequently decrease the nutrition excretion and maintain the lower cost of feed. Nutrition has also been widely accepted as a strategy to influence health and diseases of laying hens. The maintenance of good health is an important prerequisite for improving productivity and egg quality. In addition, there are many measures and strategies for minimizing the incidence of egg defects and providing a choice of lifestyle to enhance human health. This paper reviews current research progress on developing innovative technologies and strategies to maximize animal health and performance, improve the quality of egg products and minimize pollution caused by poultry production.

Percutaneous full endoscopic lumbar foraminoplasty for adjacent level foraminal stenosis following vertebral intersegmental fusion in an awake and aware patient under local anesthesia: A case report.

PubMed

Yamashita, Kazuta; Higashino, Kosaku; Sakai, Toshinori; Takata, Yoichiro; Hayashi, Fumio; Tezuka, Fumitake; Morimoto, Masatoshi; Chikawa, Takashi; Nagamachi, Akihiro; Sairyo, Koichi

2017-01-01

Percutaneous endoscopic surgery for the lumbar spine has become established in the last decade. It requires only an 8 mm skin incision, causes minimal damage to the paravertebral muscles, and can be performed under local anesthesia. With the advent of improved equipment, in particular the high-speed surgical drill, the indications for percutaneous endoscopic surgery have expanded to include lumbar spinal canal stenosis. Transforaminal percutaneous endoscopic discectomy has been used to treat intervertebral stenosis. However, it has been reported that adjacent level disc degeneration and foraminal stenosis can occur following intervertebral segmental fusion. When this adjacent level pathology becomes symptomatic, additional fusion surgery is often needed. We performed minimally invasive percutaneous full endoscopic lumbar foraminoplasty in an awake and aware 50-year-old woman under local anesthesia. The procedure was successful with no complications. Her radiculopathy, including muscle weakness and leg pain due to impingement of the exiting nerve, improved after the surgery. J. Med. Invest. 64: 291-295, August, 2017.

Overview of robotic colorectal surgery: Current and future practical developments

PubMed Central

Roy, Sudipta; Evans, Charles

2016-01-01

Minimal access surgery has revolutionised colorectal surgery by offering reduced morbidity and mortality over open surgery, while maintaining oncological and functional outcomes with the disadvantage of additional practical challenges. Robotic surgery aids the surgeon in overcoming these challenges. Uptake of robotic assistance has been relatively slow, mainly because of the high initial and ongoing costs of equipment but also because of limited evidence of improved patient outcomes. Advances in robotic colorectal surgery will aim to widen the scope of minimal access surgery to allow larger and more complex surgery through smaller access and natural orifices and also to make the technology more economical, allowing wider dispersal and uptake of robotic technology. Advances in robotic endoscopy will yield self-advancing endoscopes and a widening role for capsule endoscopy including the development of motile and steerable capsules able to deliver localised drug therapy and insufflation as well as being recharged from an extracorporeal power source to allow great longevity. Ultimately robotic technology may advance to the point where many conventional surgical interventions are no longer required. With respect to nanotechnology, surgery may eventually become obsolete. PMID:26981188

National Training and Education Standards for Health and Wellness Coaching: The Path to National Certification

PubMed Central

Wolever, Ruth Q.; Lawson, Karen; Moore, Margaret

2015-01-01

The purpose of this article is twofold: (1) to announce the findings of the job task analysis as well as national training and education standards for health and wellness coaching (HWC) that have been developed by the large-scale, collaborative efforts of the National Consortium for Credentialing Health and Wellness Coaches (NCCHWC) and (2) to invite commentary from the public. The rapid proliferation of individuals and organizations using the terms of health and/or wellness coaches and the propagation of private industry and academic coach training and education programs endeavoring to prepare these coaches has created an urgent and pressing need for national standards for use of the term health and wellness coach, as well as minimal requirements for training, education, and certification. Professionalizing the field with national standards brings a clear and consistent definition of health and wellness coaching and accepted practice standards that are uniform across the field. In addition, clear standards allow for uniform curricular criteria to ensure a minimal benchmark for education, training, and skills and knowledge evaluation of professional health and wellness coaches. PMID:25984418

GUIdock-VNC: using a graphical desktop sharing system to provide a browser-based interface for containerized software.

PubMed

Mittal, Varun; Hung, Ling-Hong; Keswani, Jayant; Kristiyanto, Daniel; Lee, Sung Bong; Yeung, Ka Yee

2017-04-01

Software container technology such as Docker can be used to package and distribute bioinformatics workflows consisting of multiple software implementations and dependencies. However, Docker is a command line-based tool, and many bioinformatics pipelines consist of components that require a graphical user interface. We present a container tool called GUIdock-VNC that uses a graphical desktop sharing system to provide a browser-based interface for containerized software. GUIdock-VNC uses the Virtual Network Computing protocol to render the graphics within most commonly used browsers. We also present a minimal image builder that can add our proposed graphical desktop sharing system to any Docker packages, with the end result that any Docker packages can be run using a graphical desktop within a browser. In addition, GUIdock-VNC uses the Oauth2 authentication protocols when deployed on the cloud. As a proof-of-concept, we demonstrated the utility of GUIdock-noVNC in gene network inference. We benchmarked our container implementation on various operating systems and showed that our solution creates minimal overhead. © The Authors 2017. Published by Oxford University Press.

A Tool for the Automated Design and Evaluation of Habitat Interior Layouts

NASA Technical Reports Server (NTRS)

Simon, Matthew A.; Wilhite, Alan W.

2013-01-01

The objective of space habitat design is to minimize mass and system size while providing adequate space for all necessary equipment and a functional layout that supports crew health and productivity. Unfortunately, development and evaluation of interior layouts is often ignored during conceptual design because of the subjectivity and long times required using current evaluation methods (e.g., human-in-the-loop mockup tests and in-depth CAD evaluations). Early, more objective assessment could prevent expensive design changes that may increase vehicle mass and compromise functionality. This paper describes a new interior design evaluation method to enable early, structured consideration of habitat interior layouts. This interior layout evaluation method features a comprehensive list of quantifiable habitat layout evaluation criteria, automatic methods to measure these criteria from a geometry model, and application of systems engineering tools and numerical methods to construct a multi-objective value function measuring the overall habitat layout performance. In addition to a detailed description of this method, a C++/OpenGL software tool which has been developed to implement this method is also discussed. This tool leverages geometry modeling coupled with collision detection techniques to identify favorable layouts subject to multiple constraints and objectives (e.g., minimize mass, maximize contiguous habitable volume, maximize task performance, and minimize crew safety risks). Finally, a few habitat layout evaluation examples are described to demonstrate the effectiveness of this method and tool to influence habitat design.

Ten-Step Minimally Invasive Spine Lumbar Decompression and Dural Repair Through Tubular Retractors.

PubMed

Boukebir, Mohamed Abdelatif; Berlin, Connor David; Navarro-Ramirez, Rodrigo; Heiland, Tim; Schöller, Karsten; Rawanduzy, Cameron; Kirnaz, Sertaç; Jada, Ajit; Härtl, Roger

2017-04-01

Minimally invasive spine (MIS) surgery utilizing tubular retractors has become an increasingly popular approach for decompression in the lumbar spine. However, a better understanding of appropriate indications, efficacious surgical techniques, limitations, and complication management is required to effectively teach the procedure and to facilitate the learning curve. To describe our experience and recommendations regarding tubular surgery for lumbar disc herniations, foraminal compression with unilateral radiculopathy, lumbar spinal stenosis, synovial cysts, and dural repair. We reviewed our experience between 2008 and 2014 to develop a step-by-step description of the surgical techniques and complication management, including dural repair through tubes, for the 4 lumbar pathologies of highest frequency. We provide additional supplementary videos for dural tear repair, laminotomy for bilateral decompression, and synovial cyst resection. Our overview and complementary materials document the key technical details to maximize the success of the 4 MIS surgical techniques. The review of our experience in 331 patients reveals technical feasibility as well as satisfying clinical results, with no postoperative complications associated with cerebrospinal fluid leaks, 1 infection, and 17 instances (5.1%) of delayed fusion. MIS surgery through tubular retractors is a safe and effective alternative to traditional open or microsurgical techniques for the treatment of lumbar degenerative disease. Adherence to strict microsurgical techniques will allow the surgeon to effectively address bilateral pathology while preserving stability and minimizing complications. Copyright © 2017 by the Congress of Neurological Surgeons

Surgery of the elderly in emergency room mode. Is there a place for laparoscopy?

PubMed

Michalik, Maciej; Dowgiałło-Wnukiewicz, Natalia; Lech, Paweł; Zacharz, Krzysztof

2017-06-01

An important yet difficult problem is qualification for surgery in elderly patients. With age the risk of comorbidities increases - multi-disease syndrome. Elderly patients suffer from frailty syndrome. Many body functions become impaired. All these factors make the elderly patient a major challenge for surgical treatment. Analysis of the possibility of developing the indications and contraindications and the criteria for surgical treatment of the elderly based on our own cases. Discussion whether there is a place for laparoscopy during surgery of the elderly in emergency room (ER) mode. The analysis was performed based on seven cases involving surgical treatment of elderly patients who were admitted to the hospital in emergency room mode. The patients were hospitalized in the General and Minimally Invasive Surgery Clinic in Olsztyn in 2016. Surgical treatment of elderly patients should be planned with multidisciplinary teams. Geriatric surgery centers should be developed to minimize the risk of overzealous treatment and potential complications. Laparoscopy should always be considered in the case of ER procedures or diagnostics. Elderly patients should not be treated as typical adults, but as a separate group of patients requiring special treatment. Due to the existing additional disease in the elderly, the frailty syndrome, any surgical intervention should be minimally invasive. The discussion about therapy should be conducted by a team of specialists from a variety of medical fields.

IONAC-Lite

NASA Technical Reports Server (NTRS)

Torgerson, Jordan L.; Clare, Loren P.; Pang, Jackson

2011-01-01

The Interplanetary Overlay Net - working Protocol Accelerator (IONAC) described previously in The Inter - planetary Overlay Networking Protocol Accelerator (NPO-45584), NASA Tech Briefs, Vol. 32, No. 10, (October 2008) p. 106 (http://www.techbriefs.com/component/ content/article/3317) provides functions that implement the Delay Tolerant Networking (DTN) bundle protocol. New missions that require high-speed downlink-only use of DTN can now be accommodated by the unidirectional IONAC-Lite to support high data rate downlink mission applications. Due to constrained energy resources, a conventional software implementation of the DTN protocol can provide only limited throughput for any given reasonable energy consumption rate. The IONAC-Lite DTN Protocol Accelerator is able to reduce this energy consumption by an order of magnitude and increase the throughput capability by two orders of magnitude. In addition, a conventional DTN implementation requires a bundle database with a considerable storage requirement. In very high downlink datarate missions such as near-Earth radar science missions, the storage space utilization needs to be maximized for science data and minimized for communications protocol-related storage needs. The IONAC-Lite DTN Protocol Accelerator is implemented in a reconfigurable hardware device to accomplish exactly what s needed for high-throughput DTN downlink-only scenarios. The following are salient features of the IONAC-Lite implementation: An implementation of the Bundle Protocol for an environment that requires a very high rate bundle egress data rate. The C&DH (command and data handling) subsystem is also expected to be very constrained so the interaction with the C&DH processor and the temporary storage are minimized. Fully pipelined design so that bundle processing database is not required. Implements a lookup table-based approach to eliminate multi-pass processing requirement imposed by the Bundle Protocol header s length field structure and the SDNV (self-delimiting numeric value) data field formatting. 8-bit parallel datapath to support high data-rate missions. Reduced resource utilization implementation for missions that do not require custody transfer features. There was no known implementation of the DTN protocol in a field programmable gate array (FPGA) device prior to the current implementation. The combination of energy and performance optimization that embodies this design makes the work novel.

Joint Data Analysis in Nutritional Epidemiology: Identification of Observational Studies and Minimal Requirements.

PubMed

Pinart, Mariona; Nimptsch, Katharina; Bouwman, Jildau; Dragsted, Lars O; Yang, Chen; De Cock, Nathalie; Lachat, Carl; Perozzi, Giuditta; Canali, Raffaella; Lombardo, Rosario; D'Archivio, Massimo; Guillaume, Michèle; Donneau, Anne-Françoise; Jeran, Stephanie; Linseisen, Jakob; Kleiser, Christina; Nöthlings, Ute; Barbaresko, Janett; Boeing, Heiner; Stelmach-Mardas, Marta; Heuer, Thorsten; Laird, Eamon; Walton, Janette; Gasparini, Paolo; Robino, Antonietta; Castaño, Luis; Rojo-Martínez, Gemma; Merino, Jordi; Masana, Luis; Standl, Marie; Schulz, Holger; Biagi, Elena; Nurk, Eha; Matthys, Christophe; Gobbetti, Marco; de Angelis, Maria; Windler, Eberhard; Zyriax, Birgit-Christiane; Tafforeau, Jean; Pischon, Tobias

2018-02-01

Joint data analysis from multiple nutrition studies may improve the ability to answer complex questions regarding the role of nutritional status and diet in health and disease. The objective was to identify nutritional observational studies from partners participating in the European Nutritional Phenotype Assessment and Data Sharing Initiative (ENPADASI) Consortium, as well as minimal requirements for joint data analysis. A predefined template containing information on study design, exposure measurements (dietary intake, alcohol and tobacco consumption, physical activity, sedentary behavior, anthropometric measures, and sociodemographic and health status), main health-related outcomes, and laboratory measurements (traditional and omics biomarkers) was developed and circulated to those European research groups participating in the ENPADASI under the strategic research area of "diet-related chronic diseases." Information about raw data disposition and metadata sharing was requested. A set of minimal requirements was abstracted from the gathered information. Studies (12 cohort, 12 cross-sectional, and 2 case-control) were identified. Two studies recruited children only and the rest recruited adults. All studies included dietary intake data. Twenty studies collected blood samples. Data on traditional biomarkers were available for 20 studies, of which 17 measured lipoproteins, glucose, and insulin and 13 measured inflammatory biomarkers. Metabolomics, proteomics, and genomics or transcriptomics data were available in 5, 3, and 12 studies, respectively. Although the study authors were willing to share metadata, most refused, were hesitant, or had legal or ethical issues related to sharing raw data. Forty-one descriptors of minimal requirements for the study data were identified to facilitate data integration. Combining study data sets will enable sufficiently powered, refined investigations to increase the knowledge and understanding of the relation between food, nutrition, and human health. Furthermore, the minimal requirements for study data may encourage more efficient secondary usage of existing data and provide sufficient information for researchers to draft future multicenter research proposals in nutrition.

Charge and energy minimization in electrical/magnetic stimulation of nervous tissue

NASA Astrophysics Data System (ADS)

Jezernik, Sašo; Sinkjaer, Thomas; Morari, Manfred

2010-08-01

In this work we address the problem of stimulating nervous tissue with the minimal necessary energy at reduced/minimal charge. Charge minimization is related to a valid safety concern (avoidance and reduction of stimulation-induced tissue and electrode damage). Energy minimization plays a role in battery-driven electrical or magnetic stimulation systems (increased lifetime, repetition rates, reduction of power requirements, thermal management). Extensive new theoretical results are derived by employing an optimal control theory framework. These results include derivation of the optimal electrical stimulation waveform for a mixed energy/charge minimization problem, derivation of the charge-balanced energy-minimal electrical stimulation waveform, solutions of a pure charge minimization problem with and without a constraint on the stimulation amplitude, and derivation of the energy-minimal magnetic stimulation waveform. Depending on the set stimulus pulse duration, energy and charge reductions of up to 80% are deemed possible. Results are verified in simulations with an active, mammalian-like nerve fiber model.

Charge and energy minimization in electrical/magnetic stimulation of nervous tissue.

PubMed

Jezernik, Saso; Sinkjaer, Thomas; Morari, Manfred

2010-08-01

In this work we address the problem of stimulating nervous tissue with the minimal necessary energy at reduced/minimal charge. Charge minimization is related to a valid safety concern (avoidance and reduction of stimulation-induced tissue and electrode damage). Energy minimization plays a role in battery-driven electrical or magnetic stimulation systems (increased lifetime, repetition rates, reduction of power requirements, thermal management). Extensive new theoretical results are derived by employing an optimal control theory framework. These results include derivation of the optimal electrical stimulation waveform for a mixed energy/charge minimization problem, derivation of the charge-balanced energy-minimal electrical stimulation waveform, solutions of a pure charge minimization problem with and without a constraint on the stimulation amplitude, and derivation of the energy-minimal magnetic stimulation waveform. Depending on the set stimulus pulse duration, energy and charge reductions of up to 80% are deemed possible. Results are verified in simulations with an active, mammalian-like nerve fiber model.

Guidance and control of swarms of spacecraft

NASA Astrophysics Data System (ADS)

Morgan, Daniel James

There has been considerable interest in formation flying spacecraft due to their potential to perform certain tasks at a cheaper cost than monolithic spacecraft. Formation flying enables the use of smaller, cheaper spacecraft that distribute the risk of the mission. Recently, the ideas of formation flying have been extended to spacecraft swarms made up of hundreds to thousands of 100-gram-class spacecraft known as femtosatellites. The large number of spacecraft and limited capabilities of each individual spacecraft present a significant challenge in guidance, navigation, and control. This dissertation deals with the guidance and control algorithms required to enable the flight of spacecraft swarms. The algorithms developed in this dissertation are focused on achieving two main goals: swarm keeping and swarm reconfiguration. The objectives of swarm keeping are to maintain bounded relative distances between spacecraft, prevent collisions between spacecraft, and minimize the propellant used by each spacecraft. Swarm reconfiguration requires the transfer of the swarm to a specific shape. Like with swarm keeping, minimizing the propellant used and preventing collisions are the main objectives. Additionally, the algorithms required for swarm keeping and swarm reconfiguration should be decentralized with respect to communication and computation so that they can be implemented on femtosats, which have limited hardware capabilities. The algorithms developed in this dissertation are concerned with swarms located in low Earth orbit. In these orbits, Earth oblateness and atmospheric drag have a significant effect on the relative motion of the swarm. The complicated dynamic environment of low Earth orbits further complicates the swarm-keeping and swarm-reconfiguration problems. To better develop and test these algorithms, a nonlinear, relative dynamic model with J2 and drag perturbations is developed. This model is used throughout this dissertation to validate the algorithms using computer simulations. The swarm-keeping problem can be solved by placing the spacecraft on J2-invariant relative orbits, which prevent collisions and minimize the drift of the swarm over hundreds of orbits using a single burn. These orbits are achieved by energy matching the spacecraft to the reference orbit. Additionally, these conditions can be repeatedly applied to minimize the drift of the swarm when atmospheric drag has a large effect (orbits with an altitude under 500 km). The swarm reconfiguration is achieved using two steps: trajectory optimization and assignment. The trajectory optimization problem can be written as a nonlinear, optimal control problem. This optimal control problem is discretized, decoupled, and convexified so that the individual femtosats can efficiently solve the optimization. Sequential convex programming is used to generate the control sequences and trajectories required to safely and efficiently transfer a spacecraft from one position to another. The sequence of trajectories is shown to converge to a Karush-Kuhn-Tucker point of the nonconvex problem. In the case where many of the spacecraft are interchangeable, a variable-swarm, distributed auction algorithm is used to determine the assignment of spacecraft to target positions. This auction algorithm requires only local communication and all of the bidding parameters are stored locally. The assignment generated using this auction algorithm is shown to be near optimal and to converge in a finite number of bids. Additionally, the bidding process is used to modify the number of targets used in the assignment so that the reconfiguration can be achieved even when there is a disconnected communication network or a significant loss of agents. Once the assignment is achieved, the trajectory optimization can be run using the terminal positions determined by the auction algorithm. To implement these algorithms in real time a model predictive control formulation is used. Model predictive control uses a finite horizon to apply the most up-to-date control sequence while simultaneously calculating a new assignment and trajectory based on updated state information. Using a finite horizon allows collisions to only be considered between spacecraft that are near each other at the current time. This relaxes the all-to-all communication assumption so that only neighboring agents need to communicate. Experimental validation is done using the formation flying testbed. The swarm-reconfiguration algorithms are tested using multiple quadrotors. Experiments have been performed using sequential convex programming for offline trajectory planning, model predictive control and sequential convex programming for real-time trajectory generation, and the variable-swarm, distributed auction algorithm for optimal assignment. These experiments show that the swarm-reconfiguration algorithms can be implemented in real time using actual hardware. In general, this dissertation presents guidance and control algorithms that maintain and reconfigure swarms of spacecraft while maintaining the shape of the swarm, preventing collisions between the spacecraft, and minimizing the amount of propellant used.

Overview on Recent Developments of Bondcoats for Plasma-Sprayed Thermal Barrier Coatings

NASA Astrophysics Data System (ADS)

Naumenko, D.; Pillai, R.; Chyrkin, A.; Quadakkers, W. J.

2017-12-01

The performance of MCrAlY (M = Ni, Co) bondcoats for atmospheric plasma-sprayed thermal barrier coatings (APS-TBCs) is substantially affected by the contents of Co, Ni, Cr, and Al as well as minor additions of Y, Hf, Zr, etc., but also by manufacturing-related properties such as coating thickness, porosity, surface roughness, and oxygen content. The latter properties depend in turn on the exact technology and set of parameters used for bondcoat deposition. The well-established LPPS process competes nowadays with alternative technologies such as HVOF and APS. In addition, new technologies have been developed for bondcoats manufacturing such as high-velocity APS or a combination of HVOF and APS for application of a flashcoat. Future developments of the bondcoat systems will likely include optimization of thermal spraying methods for obtaining complex bondcoat roughness profiles required for extended APS-TBC lifetimes. Introduction of the newest generation single-crystal superalloys possessing low Cr and high Al and refractory metals (Re, Ru) contents will require definition of new bondcoat compositions and/or multilayered bondcoats to minimize interdiffusion issues. The developments of new bondcoat compositions may be substantially facilitated using thermodynamic-kinetic modeling, the vast potential of which has been demonstrated in recent years.

Microalgae as sustainable renewable energy feedstock for biofuel production.

PubMed

Medipally, Srikanth Reddy; Yusoff, Fatimah Md; Banerjee, Sanjoy; Shariff, M

2015-01-01

The world energy crisis and increased greenhouse gas emissions have driven the search for alternative and environmentally friendly renewable energy sources. According to life cycle analysis, microalgae biofuel is identified as one of the major renewable energy sources for sustainable development, with potential to replace the fossil-based fuels. Microalgae biofuel was devoid of the major drawbacks associated with oil crops and lignocelluloses-based biofuels. Algae-based biofuels are technically and economically viable and cost competitive, require no additional lands, require minimal water use, and mitigate atmospheric CO2. However, commercial production of microalgae biodiesel is still not feasible due to the low biomass concentration and costly downstream processes. The viability of microalgae biodiesel production can be achieved by designing advanced photobioreactors, developing low cost technologies for biomass harvesting, drying, and oil extraction. Commercial production can also be accomplished by improving the genetic engineering strategies to control environmental stress conditions and by engineering metabolic pathways for high lipid production. In addition, new emerging technologies such as algal-bacterial interactions for enhancement of microalgae growth and lipid production are also explored. This review focuses mainly on the problems encountered in the commercial production of microalgae biofuels and the possible techniques to overcome these difficulties.

Plant growth-promoting bacteria for phytostabilization of mine tailings.

PubMed

Grandlic, Christopher J; Mendez, Monica O; Chorover, Jon; Machado, Blenda; Maier, Raina M

2008-03-15

Eolian dispersion of mine tailings in arid and semiarid environments is an emerging global issue for which economical remediation alternatives are needed. Phytostabilization, the revegetation of these sites with native plants, is one such alternative. Revegetation often requires the addition of bulky amendments such as compost which greatly increases cost. We report the use of plant growth-promoting bacteria (PGPB) to enhance the revegetation of mine tailings and minimize the need for compost amendment. Twenty promising PGPB isolates were used as seed inoculants in a series of greenhouse studies to examine revegetation of an extremely acidic, high metal contenttailings sample previously shown to require 15% compost amendment for normal plant growth. Several isolates significantly enhanced growth of two native species, quailbush and buffalo grass, in tailings. In this study, PGPB/compost outcomes were plant specific; for quailbush, PGPB were most effective in combination with 10% compost addition while for buffalo grass, PGPB enhanced growth in the complete absence of compost. Results indicate that selected PGPB can improve plant establishment and reduce the need for compost amendment. Further, PGPB activities necessary for aiding plant growth in mine tailings likely include tolerance to acidic pH and metals.

Plant Growth-Promoting Bacteria for Phytostabilization of Mine Tailings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grandlic, C.J.; Mendez, M.O.; Chorover, J.

2009-05-19

Eolian dispersion of mine tailings in arid and semiarid environments is an emerging global issue for which economical remediation alternatives are needed. Phytostabilization, the revegetation of these sites with native plants, is one such alternative. Revegetation often requires the addition of bulky amendments such as compost which greatly increases cost. We report the use of plant growth-promoting bacteria (PGPB) to enhance the revegetation of mine tailings and minimize the need for compost amendment. Twenty promising PGPB isolates were used as seed inoculants in a series of greenhouse studies to examine revegetation of an extremely acidic, high metal content tailings samplemore » previously shown to require 15% compost amendment for normal plant growth. Several isolates significantly enhanced growth of two native species, quailbush and buffalo grass, in tailings. In this study, PGPB/compost outcomes were plant specific; for quailbush, PGPB were most effective in combination with 10% compost addition while for buffalo grass, PGPB enhanced growth in the complete absence of compost. Results indicate that selected PGPB can improve plant establishment and reduce the need for compost amendment. Further, PGPB activities necessary for aiding plant growth in mine tailings likely include tolerance to acidic pH and metals.« less

The analysis of a generic air-to-air missile simulation model

NASA Technical Reports Server (NTRS)

Kaplan, Joseph A.; Chappell, Alan R.; Mcmanus, John W.

1994-01-01

A generic missile model was developed to evaluate the benefits of using a dynamic missile fly-out simulation system versus a static missile launch envelope system for air-to-air combat simulation. This paper examines the performance of a launch envelope model and a missile fly-out model. The launch envelope model bases its probability of killing the target aircraft on the target aircraft's position at the launch time of the weapon. The benefits gained from a launch envelope model are the simplicity of implementation and the minimal computational overhead required. A missile fly-out model takes into account the physical characteristics of the missile as it simulates the guidance, propulsion, and movement of the missile. The missile's probability of kill is based on the missile miss distance (or the minimum distance between the missile and the target aircraft). The problems associated with this method of modeling are a larger computational overhead, the additional complexity required to determine the missile miss distance, and the additional complexity of determining the reason(s) the missile missed the target. This paper evaluates the two methods and compares the results of running each method on a comprehensive set of test conditions.

Microalgae as Sustainable Renewable Energy Feedstock for Biofuel Production

PubMed Central

Yusoff, Fatimah Md.; Shariff, M.

2015-01-01

The world energy crisis and increased greenhouse gas emissions have driven the search for alternative and environmentally friendly renewable energy sources. According to life cycle analysis, microalgae biofuel is identified as one of the major renewable energy sources for sustainable development, with potential to replace the fossil-based fuels. Microalgae biofuel was devoid of the major drawbacks associated with oil crops and lignocelluloses-based biofuels. Algae-based biofuels are technically and economically viable and cost competitive, require no additional lands, require minimal water use, and mitigate atmospheric CO2. However, commercial production of microalgae biodiesel is still not feasible due to the low biomass concentration and costly downstream processes. The viability of microalgae biodiesel production can be achieved by designing advanced photobioreactors, developing low cost technologies for biomass harvesting, drying, and oil extraction. Commercial production can also be accomplished by improving the genetic engineering strategies to control environmental stress conditions and by engineering metabolic pathways for high lipid production. In addition, new emerging technologies such as algal-bacterial interactions for enhancement of microalgae growth and lipid production are also explored. This review focuses mainly on the problems encountered in the commercial production of microalgae biofuels and the possible techniques to overcome these difficulties. PMID:25874216

10 CFR 20.1406 - Minimization of contamination.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 1 2013-01-01 2013-01-01 false Minimization of contamination. 20.1406 Section 20.1406 Energy NUCLEAR REGULATORY COMMISSION STANDARDS FOR PROTECTION AGAINST RADIATION Radiological Criteria for... subsurface, in accordance with the existing radiation protection requirements in subpart B and radiological...

10 CFR 20.1406 - Minimization of contamination.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 1 2014-01-01 2014-01-01 false Minimization of contamination. 20.1406 Section 20.1406 Energy NUCLEAR REGULATORY COMMISSION STANDARDS FOR PROTECTION AGAINST RADIATION Radiological Criteria for... subsurface, in accordance with the existing radiation protection requirements in subpart B and radiological...

Minimization of required model runs in the Random Mixing approach to inverse groundwater flow and transport modeling

NASA Astrophysics Data System (ADS)

Hoerning, Sebastian; Bardossy, Andras; du Plessis, Jaco

2017-04-01

Most geostatistical inverse groundwater flow and transport modelling approaches utilize a numerical solver to minimize the discrepancy between observed and simulated hydraulic heads and/or hydraulic concentration values. The optimization procedure often requires many model runs, which for complex models lead to long run times. Random Mixing is a promising new geostatistical technique for inverse modelling. The method is an extension of the gradual deformation approach. It works by finding a field which preserves the covariance structure and maintains observed hydraulic conductivities. This field is perturbed by mixing it with new fields that fulfill the homogeneous conditions. This mixing is expressed as an optimization problem which aims to minimize the difference between the observed and simulated hydraulic heads and/or concentration values. To preserve the spatial structure, the mixing weights must lie on the unit hyper-sphere. We present a modification to the Random Mixing algorithm which significantly reduces the number of model runs required. The approach involves taking n equally spaced points on the unit circle as weights for mixing conditional random fields. Each of these mixtures provides a solution to the forward model at the conditioning locations. For each of the locations the solutions are then interpolated around the circle to provide solutions for additional mixing weights at very low computational cost. The interpolated solutions are used to search for a mixture which maximally reduces the objective function. This is in contrast to other approaches which evaluate the objective function for the n mixtures and then interpolate the obtained values. Keeping the mixture on the unit circle makes it easy to generate equidistant sampling points in the space; however, this means that only two fields are mixed at a time. Once the optimal mixture for two fields has been found, they are combined to form the input to the next iteration of the algorithm. This process is repeated until a threshold in the objective function is met or insufficient changes are produced in successive iterations.

Minimizing inner product data dependencies in conjugate gradient iteration

NASA Technical Reports Server (NTRS)

Vanrosendale, J.

1983-01-01

The amount of concurrency available in conjugate gradient iteration is limited by the summations required in the inner product computations. The inner product of two vectors of length N requires time c log(N), if N or more processors are available. This paper describes an algebraic restructuring of the conjugate gradient algorithm which minimizes data dependencies due to inner product calculations. After an initial start up, the new algorithm can perform a conjugate gradient iteration in time c*log(log(N)).

Can Wing Tip Vortices Be Accurately Simulated?

DTIC Science & Technology

2011-07-01

additional tail buffeting.2 In commercial applications, winglets have been installed on passenger aircraft to minimize vortex formation and reduce lift...air. In military applications, wing tip In commercial applications, winglets have been installed on passenger aircraft to minimize increases with downstream distances.

Minimizing corrosive action in timber bridges treated with waterborne preservatives

Treesearch

Samuel L. Zelinka; Douglas R. Rammer; James P. Wacker

2007-01-01

This work will briefly review published literature and current research activities on the corrosion of metals in contact with wood treated with waterborne alternatives to CCA. In addition, recommendations to minimize these corrosive effects in timber bridges will be discussed.

Exploration Space Suit Architecture and Destination Environmental-Based Technology Development

NASA Technical Reports Server (NTRS)

Hill, Terry R.; Korona, F. Adam; McFarland, Shane

2012-01-01

This paper continues forward where EVA Space Suit Architecture: Low Earth Orbit Vs. Moon Vs. Mars [1] left off in the development of a space suit architecture that is modular in design and could be reconfigured prior to launch or during any given mission depending on the tasks or destination. This paper will address the space suit system architecture and technologies required based upon human exploration extravehicular activity (EVA) destinations, and describe how they should evolve to meet the future exploration EVA needs of the US human space flight program.1, 2, 3 In looking forward to future US space exploration to a space suit architecture with maximum reuse of technology and functionality across a range of mission profiles and destinations, a series of exercises and analyses have provided a strong indication that the Constellation Program (CxP) space suit architecture is postured to provide a viable solution for future exploration missions4. The destination environmental analysis presented in this paper demonstrates that the modular architecture approach could provide the lowest mass and mission cost for the protection of the crew given any human mission outside of low-Earth orbit (LEO). Additionally, some of the high-level trades presented here provide a review of the environmental and non-environmental design drivers that will become increasingly important the farther away from Earth humans venture. This paper demonstrates a logical clustering of destination design environments that allows a focused approach to technology prioritization, development, and design that will maximize the return on investment, independent of any particular program, and provide architecture and design solutions for space suit systems in time or ahead of need dates for any particular crewed flight program in the future. The approach to space suit design and interface definition discussion will show how the architecture is very adaptable to programmatic and funding changes with minimal redesign effort such that the modular architecture can be quickly and efficiently honed into a specific mission point solution if required. Additionally, the modular system will allow for specific technology incorporation and upgrade as required with minimal redesign of the system.

System requirements for head down and helmet mounted displays in the military avionics environment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Flynn, M.F.; Kalmanash, M.; Sethna, V.

1996-12-31

The introduction of flat panel display technologies into the military avionics cockpit is a challenging proposition, due to the very difficult system level requirements which must be met. These relate to environmental extremes (temperature and vibrational), sever ambient lighting conditions (10,000 fL to nighttime viewing), night vision system compatibility, and wide viewing angle. At the same time, the display system must be packaged in minimal space and use minimal power. The authors will present details on the display system requirements for both head down and helmet mounted systems, as well as information on how these challenges may be overcome.

National Assessment of Energy Storage for Grid Balancing and Arbitrage: Phase 1, WECC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kintner-Meyer, Michael CW; Balducci, Patrick J.; Colella, Whitney G.

2012-06-01

To examine the role that energy storage could play in mitigating the impacts of the stochastic variability of wind generation on regional grid operation, the Pacific Northwest National Laboratory (PNNL) examined a hypothetical 2020 grid scenario in which additional wind generation capacity is built to meet renewable portfolio standard targets in the Western Interconnection. PNNL developed a stochastic model for estimating the balancing requirements using historical wind statistics and forecasting error, a detailed engineering model to analyze the dispatch of energy storage and fast-ramping generation devices for estimating size requirements of energy storage and generation systems for meeting new balancingmore » requirements, and financial models for estimating the life-cycle cost of storage and generation systems in addressing the future balancing requirements for sub-regions in the Western Interconnection. Evaluated technologies include combustion turbines, sodium sulfur (Na-S) batteries, lithium ion batteries, pumped-hydro energy storage, compressed air energy storage, flywheels, redox flow batteries, and demand response. Distinct power and energy capacity requirements were estimated for each technology option, and battery size was optimized to minimize costs. Modeling results indicate that in a future power grid with high-penetration of renewables, the most cost competitive technologies for meeting balancing requirements include Na-S batteries and flywheels.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Conroy, Aindriú; Mazumdar, Anupam; Koshelev, Alexey S., E-mail: a.conroy@lancaster.ac.uk, E-mail: alexey@ubi.pt, E-mail: a.mazumdar@lancaster.ac.uk

Einstein's General theory of relativity permits spacetime singularities, where null geodesic congruences focus in the presence of matter, which satisfies an appropriate energy condition. In this paper, we provide a minimal defocusing condition for null congruences without assuming any ansatz -dependent background solution. The two important criteria are: (1) an additional scalar degree of freedom, besides the massless graviton must be introduced into the spacetime; and (2) an infinite derivative theory of gravity is required in order to avoid tachyons or ghosts in the graviton propagator. In this regard, our analysis strengthens earlier arguments for constructing non-singular bouncing cosmologies withinmore » an infinite derivative theory of gravity, without assuming any ansatz to solve the full equations of motion.« less

Simulation of an ammonia-water heat pump water heater with combustion products-driven evaporator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Perez-Blanco, Horacio; Gluesenkamp, K.; Ally, Moonis Raza

Here, the objective of this work is to simulate a single effct (SE) ammonia-water heat pump for domestic water heating, with innovative aspects for cycle simulation and eventual implementation. Seasonal temperature variations demand verfication of distillation column viability. For the given application and temperature ranges, it is found that some variables need to be controlled if the same column is to be used all year round. In addition, a number of simplifications are considered in this work: an advanced evaporator requireing minimal gas flow and surface area, subcooling at two crucial spots of the cycle and the viability of somemore » pump designs to assuage cavitation issues.« less

Simulation of an ammonia-water heat pump water heater with combustion products-driven evaporator

DOE PAGES

Perez-Blanco, Horacio; Gluesenkamp, K.; Ally, Moonis Raza

2016-12-19

Here, the objective of this work is to simulate a single effct (SE) ammonia-water heat pump for domestic water heating, with innovative aspects for cycle simulation and eventual implementation. Seasonal temperature variations demand verfication of distillation column viability. For the given application and temperature ranges, it is found that some variables need to be controlled if the same column is to be used all year round. In addition, a number of simplifications are considered in this work: an advanced evaporator requireing minimal gas flow and surface area, subcooling at two crucial spots of the cycle and the viability of somemore » pump designs to assuage cavitation issues.« less

Computerized literature reference system: use of an optical scanner and optical character recognition software.

PubMed

Lossef, S V; Schwartz, L H

1990-09-01

A computerized reference system for radiology journal articles was developed by using an IBM-compatible personal computer with a hand-held optical scanner and optical character recognition software. This allows direct entry of scanned text from printed material into word processing or data-base files. Additionally, line diagrams and photographs of radiographs can be incorporated into these files. A text search and retrieval software program enables rapid searching for keywords in scanned documents. The hand scanner and software programs are commercially available, relatively inexpensive, and easily used. This permits construction of a personalized radiology literature file of readily accessible text and images requiring minimal typing or keystroke entry.

Shaping the future through innovations: From medical imaging to precision medicine.

PubMed

Comaniciu, Dorin; Engel, Klaus; Georgescu, Bogdan; Mansi, Tommaso

2016-10-01

Medical images constitute a source of information essential for disease diagnosis, treatment and follow-up. In addition, due to its patient-specific nature, imaging information represents a critical component required for advancing precision medicine into clinical practice. This manuscript describes recently developed technologies for better handling of image information: photorealistic visualization of medical images with Cinematic Rendering, artificial agents for in-depth image understanding, support for minimally invasive procedures, and patient-specific computational models with enhanced predictive power. Throughout the manuscript we will analyze the capabilities of such technologies and extrapolate on their potential impact to advance the quality of medical care, while reducing its cost. Copyright © 2016 Elsevier B.V. All rights reserved.

Successfully Treated Calcific Uremic Arteriolopathy: Two Cases of a High Anion Gap Metabolic Acidosis with Intravenous Sodium Thiosulfate

PubMed Central

Rein, Joshua L.; Miyata, Kana N.; Dadzie, Kobena A.; Gruber, Steven J.; Sulica, Roxana; Winchester, James F.

2014-01-01

Calcific uremic arteriolopathy (CUA) is a rare and potentially fatal disorder of calcification involving subcutaneous small vessels and fat in patients with renal insufficiency. We describe the successful use of intravenous sodium thiosulfate (STS) for the treatment of CUA in two patients. The first case was complicated by the development of a severe anion gap metabolic acidosis, which was accompanied by a seizure. Both patients had complete wound healing within five months. Although STS should be considered in the treatment of CUA, little is known about pharmacokinetics and additional studies are required to determine dosing strategies to minimize severe potential side effects. PMID:25506005

Rapid PCR amplification using a microfluidic device with integrated microwave heating and air impingement cooling.

PubMed

Shaw, Kirsty J; Docker, Peter T; Yelland, John V; Dyer, Charlotte E; Greenman, John; Greenway, Gillian M; Haswell, Stephen J

2010-07-07

A microwave heating system is described for performing polymerase chain reaction (PCR) in a microfluidic device. The heating system, in combination with air impingement cooling, provided rapid thermal cycling with heating and cooling rates of up to 65 degrees C s(-1) and minimal over- or under-shoot (+/-0.1 degrees C) when reaching target temperatures. In addition, once the required temperature was reached it could be maintained with an accuracy of +/-0.1 degrees C. To demonstrate the functionality of the system, PCR was successfully performed for the amplification of the Amelogenin locus using heating rates and quantities an order of magnitude faster and smaller than current commercial instruments.

Exercise considerations in coronary artery disease, peripheral vascular disease, and diabetes mellitus.

PubMed

Armen, Joseph; Smith, Bryan W

2003-01-01

Physical inactivity is a risk factor for cardiovascular disease. Regular aerobic and resistance training increases exercise capacity and plays a role both in the primary and secondary prevention of cardiovascular disease. Patients with coronary artery disease, peripheral vascular disease, or diabetes mellitus must be considered individually when prescribing exercise because their clinical status can vary greatly. In addition, a majority of these patients have multiple comorbid disorders such as renal, neurologic, and retinal disease that may affect their ability to exercise safely. Therefore, a preparticipation medical evaluation is required. An exercise prescription should be tailored to each person's unique set of circumstances and reflect an effort to maximize the anticipated benefits while minimizing the risks.

Bootstrap and fast wave current drive for tokamak reactors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ehst, D.A.

1991-09-01

Using the multi-species neoclassical treatment of Hirshman and Sigmar we study steady state bootstrap equilibria with seed currents provided by low frequency (ICRF) fast waves and with additional surface current density driven by lower hybrid waves. This study applies to reactor plasmas of arbitrary aspect ratio. IN one limit the bootstrap component can supply nearly the total equilibrium current with minimal driving power (< 20 MW). However, for larger total currents considerable driving power is required (for ITER: I{sub o} = 18 MA needs P{sub FW} = 15 MW, P{sub LH} = 75 MW). A computational survey of bootstrap fractionmore » and current drive efficiency is presented. 11 refs., 8 figs.« less

Low-Intensity Extracorporeal Shock Wave as a Novel Treatment for Erectile Dysfunction.

PubMed

Pan, Michael M; Raees, Ayman; Kovac, Jason R

2016-03-01

The paradigm of erectile dysfunction (ED) treatment was fundamentally altered following the introduction of oral phosphodiesterase type 5 inhibitors. Unfortunately, a significant number of men exhibit a suboptimal response and require additional management strategies. One of the novel, minimally invasive strategies being developed is low-intensity extracorporeal shock wave therapy. Used in the hope of delaying placement of an inflatable penile prosthesis, the final phase of ED treatment, low-intensity extracorporeal shock wave therapy is a unique application of an established technology that may hopefully one day expand the medical options for patients with ED. This commentary will highlight the physiology underlying this technique and summarize the most recent studies. © The Author(s) 2015.

Polyproline as a Minimal Antifreeze Protein Mimic That Enhances the Cryopreservation of Cell Monolayers

PubMed Central

Graham, Ben; Bailey, Trisha L.; Healey, Joseph R. J.; Marcellini, Moreno; Deville, Sylvain

2017-01-01

Abstract Tissue engineering, gene therapy, drug screening, and emerging regenerative medicine therapies are fundamentally reliant on high‐quality adherent cell culture, but current methods to cryopreserve cells in this format can give low cell yields and require large volumes of solvent “antifreezes”. Herein, we report polyproline as a minimum (bio)synthetic mimic of antifreeze proteins that is accessible by solution, solid‐phase, and recombinant methods. We demonstrate that polyproline has ice recrystallisation inhibition activity linked to its amphipathic helix and that it enhances the DMSO cryopreservation of adherent cell lines. Polyproline may be a versatile additive in the emerging field of macromolecular cryoprotectants. PMID:29044869

Polyproline as a Minimal Antifreeze Protein Mimic That Enhances the Cryopreservation of Cell Monolayers.

PubMed

Graham, Ben; Bailey, Trisha L; Healey, Joseph R J; Marcellini, Moreno; Deville, Sylvain; Gibson, Matthew I

2017-12-11

Tissue engineering, gene therapy, drug screening, and emerging regenerative medicine therapies are fundamentally reliant on high-quality adherent cell culture, but current methods to cryopreserve cells in this format can give low cell yields and require large volumes of solvent "antifreezes". Herein, we report polyproline as a minimum (bio)synthetic mimic of antifreeze proteins that is accessible by solution, solid-phase, and recombinant methods. We demonstrate that polyproline has ice recrystallisation inhibition activity linked to its amphipathic helix and that it enhances the DMSO cryopreservation of adherent cell lines. Polyproline may be a versatile additive in the emerging field of macromolecular cryoprotectants. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

10 CFR 20.1406 - Minimization of contamination.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 1 2012-01-01 2012-01-01 false Minimization of contamination. 20.1406 Section 20.1406 Energy NUCLEAR REGULATORY COMMISSION STANDARDS FOR PROTECTION AGAINST RADIATION Radiological Criteria for..., including the subsurface, in accordance with the existing radiation protection requirements in Subpart B and...

Minimum Control Requirements for Advanced Life Support Systems

NASA Technical Reports Server (NTRS)

Boulange, Richard; Jones, Harry; Jones, Harry

2002-01-01

Advanced control technologies are not necessary for the safe, reliable and continuous operation of Advanced Life Support (ALS) systems. ALS systems can and are adequately controlled by simple, reliable, low-level methodologies and algorithms. The automation provided by advanced control technologies is claimed to decrease system mass and necessary crew time by reducing buffer size and minimizing crew involvement. In truth, these approaches increase control system complexity without clearly demonstrating an increase in reliability across the ALS system. Unless these systems are as reliable as the hardware they control, there is no savings to be had. A baseline ALS system is presented with the minimal control system required for its continuous safe reliable operation. This baseline control system uses simple algorithms and scheduling methodologies and relies on human intervention only in the event of failure of the redundant backup equipment. This ALS system architecture is designed for reliable operation, with minimal components and minimal control system complexity. The fundamental design precept followed is "If it isn't there, it can't fail".

The pedicled internal pudendal artery perforator (PIPAP) flap for ischial pressure sore reconstruction: Technique and long-term outcome of a cohort study.

PubMed

Legemate, Catherine M; van der Kwaak, Monique; Gobets, David; Huikeshoven, Menno; van Zuijlen, Paul P M

2018-06-01

The ischial region is the site most affected by pressure sores and has the highest recurrence and complication rates compared to other affected sites. We developed a practical and safe pedicled flap for reconstruction of ischial pressure sores based on the rich available perforators from the internal pudendal artery and the surplus of skin at the infragluteal fold. A retrospective cohort study was conducted in all patients who underwent ischial pressure ulcer reconstruction using the PIPAP flap between March 2010 and March 2017. The skin flap was designed along the gluteal fold. The skin perforators of the pudendal artery were marked with a Doppler probe in the medial region of the gluteal fold. Surgery was performed in the jackknife position, and flaps were elevated in the suprafascial plane. Patients were assessed for minor (requiring no additional surgery) and major complications (requiring additional surgery). Twenty-seven patients (34 flaps) were identified. The median follow-up period was 38 months (IQR 37). Primary closure of the donor-site was achieved in all procedures, only one flap required muscle flap transposition in order to fill the dead space. The mean operating time was 60 ± 21 minutes. In six flaps (9%) wound healing problems were noted that did not require an additional operative procedure. Among the nine flaps (27%) that required a second procedure, 3 (9%) were necessary due to recurrent ulcers. The PIPAP flap is a safe and reliable alternative for ischial pressure sore reconstruction, certainly when compared to available techniques. Moreover, it has significant advantages over other techniques including minimal donor-site morbidity, preservation of posterior thigh skin, buttock-line integrity and reliable vascularity. Copyright © 2018 British Association of Plastic, Reconstructive and Aesthetic Surgeons. Published by Elsevier Ltd. All rights reserved.

Design-for-Six-Sigma To Develop a Bioprocess Knowledge Management Framework.

PubMed

Junker, Beth; Maheshwari, Gargi; Ranheim, Todd; Altaras, Nedim; Stankevicz, Michael; Harmon, Lori; Rios, Sandra; D'anjou, Marc

2011-01-01

Owing to the high costs associated with biopharmaceutical development, considerable pressure has developed for the biopharmaceutical industry to increase productivity by becoming more lean and flexible. The ability to reuse knowledge was identified as one key advantage to streamline productivity, efficiently use resources, and ultimately perform better than the competition. A knowledge management (KM) strategy was assembled for bioprocess-related information using the technique of Design-for-Six-Sigma (DFSS). This strategy supported quality-by-design and process validation efforts for pipeline as well as licensed products. The DFSS technique was selected because it was both streamlined and efficient. These characteristics permitted development of a KM strategy with minimized team leader and team member resources. DFSS also placed a high emphasis on the voice of the customer, information considered crucial to the selection of solutions most appropriate for the current knowledge-based challenges of the organization. The KM strategy developed was comprised of nine workstreams, constructed from related solution buckets which in turn were assembled from the individual solution tasks that were identified. Each workstream's detailed design was evaluated against published and established best practices, as well as the KM strategy project charter and design inputs. Gaps and risks were identified and mitigated as necessary to improve the robustness of the proposed strategy. Aggregated resources (specifically expense/capital funds and staff) and timing were estimated to obtain vital management sponsorship for implementation. Where possible, existing governance and divisional/corporate information technology efforts were leveraged to minimize the additional bioprocess resources required for implementation. Finally, leading and lagging indicator metrics were selected to track the success of pilots and eventual implementation. A knowledge management framework was assembled for bioprocess-related information using a streamlined and efficient technique that minimized team leader and member resources. The technique also highly emphasized input from the staff, who generated and used the knowledge, information considered crucial to selection of solutions most appropriate for the current knowledge-based challenges in the organization. The framework developed was comprised of nine workstreams, constructed from related solution buckets which were assembled from individual solution tasks that were identified. Each workstream's detailed design was evaluated against published and established best practices, as well as the project charter and design inputs. Gaps and risks were identified and mitigated to improve robustness of the proposed framework. Aggregated resources (specifically expense/capital funds and staff) and timing were estimated to obtain vital management sponsorship for implementation. Where possible, existing governance and information technology efforts were leveraged to minimize additional bioprocess resources required for implementation. Finally, metrics were selected to track the success of pilots and eventual implementation.

Crossed, Small-Deflection Energy Analyzer for Wind/Temperature Spectrometer

NASA Technical Reports Server (NTRS)

Herrero, Federico A.; Finne, Theodore T.

2010-01-01

Determination of neutral winds and ion drifts in low-Earth-orbit missions requires measurements of the angular and energy distributions of the flux of neutrals and ions entering the satellite from the ram direction. The magnitude and direction of the neutral-wind (or ion-drift) determine the location of the maximum in the angular distribution of the flux. Knowledge of the angle of maximum flux with respect to satellite coordinates (pointing) is essential to determine the wind (or ion-drift) vector. The crossed Small-Deflection Energy Analyzer (SDEA) spectrometer (see Figure 1) occupies minimal volume and consumes minimal power. Designed for upper atmosphere/ionosphere investigations at Earth altitudes above 100 km, the spectrometer operates by detecting the angular and energy distributions of neutral atoms/molecules and ions in two mutually perpendicular planes. In this configuration, the two detection planes actually cross at the spectrometer center. It is possible to merge two SDEAs so they share a common optical axis and alternate measurements between two perpendicular planes, and reduce the number of ion sources from two to one. This minimizes the volume and footprint significantly and reduces the ion source power by a factor of two. The area of the entrance aperture affects the number of ions detected/second and also determines the energy resolution. Thermionic emitters require heater power of about 100 mW to produce 1 mA of electron beam current. Typically, electron energy is about 100 eV and requires a 100-V supply for electron acceleration to supply an additional 100 mW of power. Thus, ion source power is at most 200 mW. If two ion sources were to be used, the ion source power would be, at most, 400 mW. Detector power, deflection voltage power, and microcontroller and other functions require less than 150 mW. A WTS (wind/ temperature spectrometer) with two separate optical axes would consume about 650 mW, while the crossed SDEA described here consumes about 350 mW. The entrance aperture has a diameter of 0.004 in. (0.10 mm) to provide the required energy resolution between 0.05 and 0.15. This design (see Figure 2) provides a WTS occupying a volume less than 40 cm(sup 3), on a footprint of diameter about 1.5 in. (38 mm). The Crossed SDEA offers many advantages in the measurements of neutral wind and ion drifts in the Earth's thermosphere. As such, it will be useful in future commercial satellites dedicated to monitoring the ionosphere with a view to improving the integrity and predictability of GPS operations.

Data forwarding mechanism for supporting real-time services during relocations in UMTS systems

NASA Astrophysics Data System (ADS)

Cai, Wei; Liao, Xianglong; Zheng, Liang; Liu, Zehong

2004-04-01

To minimize the interruption during the handovers or relocations invoked by subscribers moving is a very critical factor to enhance the performance of the UMTS systems. We know that the 2G systems have been optimized to minimize the interruption of speech during handovers by two main technologies: one is the bi-casting for the DL traffic and the other is the fast radio resynchronization by the UE for the UL traffic. In the UMTS systems, we have also implemented lossless relocations for non real-time services with high reliability by data buffering in the source RNC and target RNC for the UE. However, the UMTS systems support four QoS classes traffic flow: conversational class, streaming class, interactive class and background class. The main distinguishing factor between these QoS classes is how delay sensitive the traffic is: Conversational and Streaming classes are mainly used to carry real-time traffic flows, like video telephony, interactive and background classes are mainly used by traditional Internet applications like WWW, E-mail and FTP. It"s essential to provide the solutions for supporting real-time services to meet the requirement for QoS in UMTS systems. Apparently, the Data buffering mechanism is not adapted to real-time services because of it"s delay may exceed the basic requirement for real-time services. Under this background, the paper discussed two data forwarding solutions for real-time services from the PS domain in the UMTS systems: packet duplication and Core Network bi-casting. The former mechanism does not require any new procedures, messages nor information elements. The later mechanism requires that the GGSN or SGSN is able to bi-cast the DL traffic to the target RNC according to the relocations involving two SGSNs or just involving one SGSN. It also implicitly shows that we need change procedures at the nodes SGSN, GGSN and RNC which are involved in the relocation procedure based on existing procedures that we have already designed if adopt the later solution. In a detail way, the paper analyzed the characteristic for these two solutions respectively, concentrated on the packet flows and the message flows in those nodes involved in relocations. Additionally, also gave out the impact on present transport technologies in the wireless communication systems. However we shall minimize the impact of evolution of transport mechanism and utilize the resource efficiently according to the general requirements for QoS in UMTS systems.

Aortic Wave Dynamics and Its Influence on Left Ventricular Workload

PubMed Central

Pahlevan, Niema M.; Gharib, Morteza

2011-01-01

The pumping mechanism of the heart is pulsatile, so the heart generates pulsatile flow that enters into the compliant aorta in the form of pressure and flow waves. We hypothesized that there exists a specific heart rate at which the external left ventricular (LV) power is minimized. To test this hypothesis, we used a computational model to explore the effects of heart rate (HR) and aortic rigidity on left ventricular (LV) power requirement. While both mean and pulsatile parts of the pressure play an important role in LV power requirement elevation, at higher rigidities the effect of pulsatility becomes more dominant. For any given aortic rigidity, there exists an optimum HR that minimizes the LV power requirement at a given cardiac output. The optimum HR shifts to higher values as the aorta becomes more rigid. To conclude, there is an optimum condition for aortic waves that minimizes the LV pulsatile load and consequently the total LV workload. PMID:21853075

Extension of the lower bound of monitor solutions of maximally permissive supervisors to non-α net systems

NASA Astrophysics Data System (ADS)

Wu, W. H.; Chao, D. Y.

2016-07-01

Traditional region-based liveness-enforcing supervisors focus on (1) maximal permissiveness of not losing legal states, (2) structural simplicity of minimal number of monitors, and (3) fast computation. Lately, a number of similar approaches can achieve minimal configuration using efficient linear programming. However, it is unclear as to the relationship between the minimal configuration and the net structure. It is important to explore the structures involved for the fewest monitors required. Once the lower bound is achieved, further iteration to merge (or reduce the number of) monitors is not necessary. The minimal strongly connected resource subnet (i.e., all places are resources) that contains the set of resource places in a basic siphon is an elementary circuit. Earlier, we showed that the number of monitors required for liveness-enforcing and maximal permissiveness equals that of basic siphons for a subclass of Petri nets modelling manufacturing, called α systems. This paper extends this to systems more powerful than the α one so that the number of monitors in a minimal configuration remains to be lower bounded by that of basic siphons. This paper develops the theory behind and shows examples.

Pricing health benefits: a cost-minimization approach.

PubMed

Miller, Nolan H

2005-09-01

We study the role of health benefits in an employer's compensation strategy, given the overall goal of minimizing total compensation cost (wages plus health-insurance cost). When employees' health status is private information, the employer's basic benefit package consists of a base wage and a moderate health plan, with a generous plan available for an additional charge. We show that in setting the charge for the generous plan, a cost-minimizing employer should act as a monopolist who sells "health plan upgrades" to its workers, and we discuss ways tax policy can encourage efficiency under cost-minimization and alternative pricing rules.

International Myeloma Working Group recommendations for global myeloma care.

PubMed

Ludwig, H; Miguel, J S; Dimopoulos, M A; Palumbo, A; Garcia Sanz, R; Powles, R; Lentzsch, S; Ming Chen, W; Hou, J; Jurczyszyn, A; Romeril, K; Hajek, R; Terpos, E; Shimizu, K; Joshua, D; Hungria, V; Rodriguez Morales, A; Ben-Yehuda, D; Sondergeld, P; Zamagni, E; Durie, B

2014-05-01

Recent developments have led to remarkable improvements in the assessment and treatment of patients with multiple myeloma (MM). New technologies have become available to precisely evaluate the biology and extent of the disease, including information about cytogenetics and genetic abnormalities, extramedullary manifestations and minimal residual disease. New, more effective drugs have been introduced into clinical practice, which enable clinicians to significantly improve the outcome of patients but also pose new challenges for the prevention and management of their specific side effects. Given these various new options and challenges, it is important to identify the minimal requirements for diagnosis and treatment of patients, as access to the most sophisticated advances may vary depending on local circumstances. Here, we propose the minimal requirements and possible options for diagnosis, monitoring and treatment of patients with multiple myeloma.

Optimal mistuning for enhanced aeroelastic stability of transonic fans

NASA Technical Reports Server (NTRS)

Hall, K. C.; Crawley, E. F.

1983-01-01

An inverse design procedure was developed for the design of a mistuned rotor. The design requirements are that the stability margin of the eigenvalues of the aeroelastic system be greater than or equal to some minimum stability margin, and that the mass added to each blade be positive. The objective was to achieve these requirements with a minimal amount of mistuning. Hence, the problem was posed as a constrained optimization problem. The constrained minimization problem was solved by the technique of mathematical programming via augmented Lagrangians. The unconstrained minimization phase of this technique was solved by the variable metric method. The bladed disk was modelled as being composed of a rigid disk mounted on a rigid shaft. Each of the blades were modelled with a single tosional degree of freedom.

78 FR 33995 - Nuclear Proliferation Assessment in Licensing Process for Enrichment or Reprocessing Facilities

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-06

... designed to minimize proliferation risks world-wide, including the Nuclear Non- Proliferation Treaty, the U... and licensees ensure that they comply with requirements designed to minimize proliferation risks... NRC's regulations on physical security, information security, material control and accounting, cyber...

Minimization search method for data inversion

NASA Technical Reports Server (NTRS)

Fymat, A. L.

1975-01-01

Technique has been developed for determining values of selected subsets of independent variables in mathematical formulations. Required computation time increases with first power of the number of variables. This is in contrast with classical minimization methods for which computational time increases with third power of the number of variables.

7 CFR 1940.319 - Completing environmental assessments for Class I actions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... a mechanism for reviewing actions with normally minimal impacts and for documenting a finding of no significant impact, as well as compliance determinations for other applicable environmental laws, regulations... actions which have more than minimal impacts and which, therefore, require a more detailed environmental...

Radiation Shielding Design and Orientation Considerations for a 1 kWe Heat Pipe Cooled Reactor Utilized to Bore Through the Ice Caps of Mars

NASA Astrophysics Data System (ADS)

Fensin, Michael L.; Elliott, John O.; Lipinski, Ronald J.; Poston, David I.

2006-01-01

The goal in designing any space power system is to develop a system able to meet the mission requirements for success while minimizing the overall costs. The mission requirements for the this study was to develop a reactor (with Stirling engine power conversion) and shielding configuration able to fit, along with all the other necessary science equipment, in a Cryobot 3 m high with ~0.5 m diameter hull, produce 1 kWe for 5yrs, and not adversely affect the mission science by keeping the total integrated dose to the science equipment below 150 krad. Since in most space power missions the overall system mass dictates the mission cost, the shielding designs in this study incorporated Martian water extracted at the startup site in order to minimize the tungsten and LiH mass loading at launch. Different reliability and mass minimization concerns led to three design configuration evolutions. With the help of implementing Martian water and configuring the reactor as far from the science equipment as possible, the needed tungsten and LiH shield mass was minimized. This study further characterizes the startup dose and the necessary mission requirements in order to ensure integrity of the surface equipment during reactor startup phase.

Management of Peritonitis After Minimally Invasive Colorectal Surgery: Can We Stick to Laparoscopy?

PubMed

Marano, Alessandra; Giuffrida, Maria Carmela; Giraudo, Giorgio; Pellegrino, Luca; Borghi, Felice

2017-04-01

Although laparoscopy is becoming the standard of care for the treatment of colorectal disease, its application in case of postoperative peritonitis is still not widespread. The objective of this article is to evaluate the role of laparoscopy in the management of postoperative peritonitis after elective minimally invasive colorectal resection for malignant and benign diseases. Between April 2010 and May 2016, 536 patients received primary minimally invasive colorectal surgery at our Department. Among this series, we carried out a retrospective study of those patients who, having developed signs of peritonitis, were treated with a laparoscopic reintervention. Patient demographics, type of complication and of the main relaparoscopic treatment, and main outcomes of reoperation were recorded. A total of 20 patients (3.7%) underwent relaparoscopy for the management of postoperative peritonitis, of which exact causes were detected by laparoscopy in 75% as follows: anastomotic leakage (n = 8, 40%), colonic ischemia (n = 2, 10%), iatrogenic bowel tear (n = 4, 20%), and other (n = 1, 5%). The median time between operations was 3.5 days (range, 2-8). The laparoscopic reintervention was tailored case by case and ranged from lavage and drainage to redo anastomosis with ostomy fashioning. Conversion rate was 10% and overall morbidity was 50%. No cases required additional surgery and 30-day mortality was nil. Three patients (15%) were admitted to intensive care unit for 24-hour surveillance. Our experience suggests that in experienced hands and in hemodynamically stable patients, a prompt laparoscopic reoperation appears as an accurate diagnostic tool and an effective and safe option for the treatment of postoperative peritonitis after primary colorectal minimally invasive surgery.

Removal of Gross Air Embolization from Cardiopulmonary Bypass Circuits with Integrated Arterial Line Filters: A Comparison of Circuit Designs.

PubMed

Reagor, James A; Holt, David W

2016-03-01

Advances in technology, the desire to minimize blood product transfusions, and concerns relating to inflammatory mediators have lead many practitioners and manufacturers to minimize cardiopulmonary bypass (CBP) circuit designs. The oxygenator and arterial line filter (ALF) have been integrated into one device as a method of attaining a reduction in prime volume and surface area. The instructions for use of a currently available oxygenator with integrated ALF recommends incorporating a recirculation line distal to the oxygenator. However, according to an unscientific survey, 70% of respondents utilize CPB circuits incorporating integrated ALFs without a path of recirculation distal to the oxygenator outlet. Considering this circuit design, the ability to quickly remove a gross air bolus in the blood path distal to the oxygenator may be compromised. This in vitro study was designed to determine if the time required to remove a gross air bolus from a CPB circuit without a path of recirculation distal to the oxygenator will be significantly longer than that of a circuit with a path of recirculation distal to the oxygenator. A significant difference was found in the mean time required to remove a gross air bolus between the circuit designs (p = .0003). Additionally, There was found to be a statistically significant difference in the mean time required to remove a gross air bolus between Trial 1 and Trials 4 (p = .015) and 5 (p =.014) irrespective of the circuit design. Under the parameters of this study, a recirculation line distal to an oxygenator with an integrated ALF significantly decreases the time it takes to remove an air bolus from the CPB circuit and may be safer for clinical use than the same circuit without a recirculation line.

A Multi-User Model for Effectively Communicating Research Through Electronic Media

NASA Astrophysics Data System (ADS)

Hinds, J. J.; Fairley, J. P.

2003-12-01

Electronic media have demonstrated potential for data exchange, dissemination of results to other scientists, communication with community interest groups, and education of the general public regarding scientific advances. Few researchers, however, receive training in the skills required to capture the attention of the broad spectrum of Internet users. Because different people assimilate information in different ways, effective communication is best accomplished using an appropriate mix of photographs, graphics, tables, and text. In addition, effective web page design requires a clear, consistent organizational structure, easily-navigated layout, and attention to details such as page printability, downloading time, and minimal page scrolling. One of the strengths of electronic media is that the user can chose an appropriate level of involvement for his or her interest. In designing a web page for the multidisciplinary NSF/EPSCoR "Biocomplexity in Extreme Environments" project, we divided potential users into three categories based on our perception of the level of detail they required: 1) project participants, 2) non-participants with technical backgrounds, and 3) the general public. By understanding the needs and expectations of potential viewers, it was possible to present each group with an appropriate balance of visual and textural elements. For example, project participants are often most interested in raw data, which can be effectively presented in tabular format. Non-participants with technical backgrounds are more interested in analyzed data, while a project overview, presented through photographs and graphics with minimal text, will be most effective for communicating with the general public. The completed web page illustrates one solution for effectively communicating with a diverse audience, and provides examples for meeting many of the challenges of web page design.

20 CFR 641.430 - What are the eligibility criteria that each applicant must meet?

Code of Federal Regulations, 2010 CFR

2010-04-01

... disruption for current participants if there is a change in project sponsor and/or location, and its plan for minimizing disruptions; and (h) Any additional criteria that the Secretary of Labor deems appropriate in order to minimize disruptions for current participants. ...

The Blueprint of a Minimal Cell: MiniBacillus

PubMed Central

Reuß, Daniel R.; Commichau, Fabian M.; Gundlach, Jan; Zhu, Bingyao

2016-01-01

SUMMARY Bacillus subtilis is one of the best-studied organisms. Due to the broad knowledge and annotation and the well-developed genetic system, this bacterium is an excellent starting point for genome minimization with the aim of constructing a minimal cell. We have analyzed the genome of B. subtilis and selected all genes that are required to allow life in complex medium at 37°C. This selection is based on the known information on essential genes and functions as well as on gene and protein expression data and gene conservation. The list presented here includes 523 and 119 genes coding for proteins and RNAs, respectively. These proteins and RNAs are required for the basic functions of life in information processing (replication and chromosome maintenance, transcription, translation, protein folding, and secretion), metabolism, cell division, and the integrity of the minimal cell. The completeness of the selected metabolic pathways, reactions, and enzymes was verified by the development of a model of metabolism of the minimal cell. A comparison of the MiniBacillus genome to the recently reported designed minimal genome of Mycoplasma mycoides JCVI-syn3.0 indicates excellent agreement in the information-processing pathways, whereas each species has a metabolism that reflects specific evolution and adaptation. The blueprint of MiniBacillus presented here serves as the starting point for a successive reduction of the B. subtilis genome. PMID:27681641

Multidimensional NMR inversion without Kronecker products: Multilinear inversion

NASA Astrophysics Data System (ADS)

Medellín, David; Ravi, Vivek R.; Torres-Verdín, Carlos

2016-08-01

Multidimensional NMR inversion using Kronecker products poses several challenges. First, kernel compression is only possible when the kernel matrices are separable, and in recent years, there has been an increasing interest in NMR sequences with non-separable kernels. Second, in three or more dimensions, the singular value decomposition is not unique; therefore kernel compression is not well-defined for higher dimensions. Without kernel compression, the Kronecker product yields matrices that require large amounts of memory, making the inversion intractable for personal computers. Finally, incorporating arbitrary regularization terms is not possible using the Lawson-Hanson (LH) or the Butler-Reeds-Dawson (BRD) algorithms. We develop a minimization-based inversion method that circumvents the above problems by using multilinear forms to perform multidimensional NMR inversion without using kernel compression or Kronecker products. The new method is memory efficient, requiring less than 0.1% of the memory required by the LH or BRD methods. It can also be extended to arbitrary dimensions and adapted to include non-separable kernels, linear constraints, and arbitrary regularization terms. Additionally, it is easy to implement because only a cost function and its first derivative are required to perform the inversion.

Global Precipitation Measurement (GPM) Orbit Design and Autonomous Maneuvers

NASA Technical Reports Server (NTRS)

Folta, David; Mendelsohn, Chad

2003-01-01

The NASA Goddard Space Flight Center's Global Precipitation Measurement (GPM) mission will meet a challenge of measuring worldwide precipitation every three hours. The GPM spacecraft, part of a constellation, will be required to maintain a circular orbit in a high drag environment to accomplish this challenge. Analysis by the Flight Dynamics Analysis Branch has shown that the prime orbit altitude of 40% is necessary to prevent ground track repeating. Combined with goals to minimize maneuver impacts to science data collection and enabling reasonable long-term orbit predictions, the GPM project has decided to fly an autonomous maneuver system. This system is a derivative of the successful New Millennium Program technology flown onboard the Earth Observing-1 mission. This paper presents the driving science requirements and goals of the mission and shows how they will be met. Analysis of the orbit optimization and the AV requirements for several ballistic properties are presented. The architecture of the autonomous maneuvering system to meet the goals and requirements is presented along with simulations using a GPM prototype. Additionally, the use of the GPM autonomous system to mitigate possible collision avoidance and to aid other spacecraft systems during navigation outages is explored.

Best Practices for Fatigue Risk Management in Non-Traditional Shiftwork

NASA Technical Reports Server (NTRS)

Flynn-Evans, Erin E.

2016-01-01

Fatigue risk management programs provide effective tools to mitigate fatigue among shift workers. Although such programs are effective for typical shiftwork scenarios, where individuals of equal skill level can be divided into shifts to cover 24 hour operations, traditional programs are not sufficient for managing sleep loss among individuals with unique skill sets, in occupations where non-traditional schedules are required. Such operations are prevalent at NASA and in other high stress occupations, including among airline pilots, military personnel, and expeditioners. These types of operations require fatigue risk management programs tailored to the specific requirements of the mission. Without appropriately tailored fatigue risk management, such operations can lead to an elevated risk of operational failure, disintegration of teamwork, and increased risk of accidents and incidents. In order to design schedules for such operations, schedule planners must evaluate the impact of a given operation on circadian misalignment, acute sleep loss, chronic sleep loss and sleep inertia. In addition, individual-level factors such as morningness-eveningness preference and sleep disorders should be considered. After the impact of each of these factors has been identified, scheduling teams can design schedules that meet operational requirements, while also minimizing fatigue.

Transfers between libration-point orbits in the elliptic restricted problem

NASA Astrophysics Data System (ADS)

Hiday-Johnston, L. A.; Howell, K. C.

1994-04-01

A strategy is formulated to design optimal time-fixed impulsive transfers between three-dimensional libration-point orbits in the vicinity of the interior L1 libration point of the Sun-Earth/Moon barycenter system. The adjoint equation in terms of rotating coordinates in the elliptic restricted three-body problem is shown to be of a distinctly different form from that obtained in the analysis of trajectories in the two-body problem. Also, the necessary conditions for a time-fixed two-impulse transfer to be optimal are stated in terms of the primer vector. Primer vector theory is then extended to nonoptimal impulsive trajectories in order to establish a criterion whereby the addition of an interior impulse reduces total fuel expenditure. The necessary conditions for the local optimality of a transfer containing additional impulses are satisfied by requiring continuity of the Hamiltonian and the derivative of the primer vector at all interior impulses. Determination of location, orientation, and magnitude of each additional impulse is accomplished by the unconstrained minimization of the cost function using a multivariable search method. Results indicate that substantial savings in fuel can be achieved by the addition of interior impulsive maneuvers on transfers between libration-point orbits.

Validation of Reverse-Engineered and Additive-Manufactured Microsurgical Instrument Prototype.

PubMed

Singh, Ramandeep; Suri, Ashish; Anand, Sneh; Baby, Britty

2016-12-01

With advancements in imaging techniques, neurosurgical procedures are becoming highly precise and minimally invasive, thus demanding development of new ergonomically aesthetic instruments. Conventionally, neurosurgical instruments are manufactured using subtractive manufacturing methods. Such a process is complex, time-consuming, and impractical for prototype development and validation of new designs. Therefore, an alternative design process has been used utilizing blue light scanning, computer-aided designing, and additive manufacturing direct metal laser sintering (DMLS) for microsurgical instrument prototype development. Deviations of DMLS-fabricated instrument were studied by superimposing scan data of fabricated instrument with the computer-aided designing model. Content and concurrent validity of the fabricated prototypes was done by a group of 15 neurosurgeons by performing sciatic nerve anastomosis in small laboratory animals. Comparative scoring was obtained for the control and study instrument. T test was applied to the individual parameters and P values for force (P < .0001) and surface roughness (P < .01) were found to be statistically significant. These 2 parameters were further analyzed using objective measures. Results depicts that additive manufacturing by DMLS provides an effective method for prototype development. However, direct application of these additive-manufactured instruments in the operating room requires further validation. © The Author(s) 2016.

Robotic cardiac surgery: an anaesthetic challenge.

PubMed

Wang, Gang; Gao, Changqing

2014-08-01

Robotic cardiac surgery with the da Vinci robotic surgical system offers the benefits of a minimally invasive procedure, including a smaller incision and scar, reduced risk of infection, less pain and trauma, less bleeding and blood transfusion requirements, shorter hospital stay and decreased recovery time. Robotic cardiac surgery includes extracardiac and intracardiac procedures. Extracardiac procedures are often performed on a beating heart. Intracardiac procedures require the aid of peripheral cardiopulmonary bypass via a minithoracotomy. Robotic cardiac surgery, however, poses challenges to the anaesthetist, as the obligatory one-lung ventilation (OLV) and CO2 insufflation may reduce cardiac output and increase pulmonary vascular resistance, potentially resulting in hypoxaemia and haemodynamic compromise. In addition, surgery requires appropriate positioning of specialised cannulae such as an endopulmonary vent, endocoronary sinus catheter, and endoaortic clamp catheter under the guidance of transoesophageal echocardiography. Therefore, cardiac anaesthetists should have a working knowledge of these systems, OLV and haemodynamic support. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Ongoing Development of a Series Bosch Reactor System

NASA Technical Reports Server (NTRS)

Abney, Morgan; Mansell, Matt; DuMez, Sam; Thomas, John; Cooper, Charlie; Long, David

2013-01-01

Future manned missions to deep space or planetary surfaces will undoubtedly require highly robust, efficient, and regenerable life support systems that require minimal consumables. To meet this requirement, NASA continues to explore a Bosch-based carbon dioxide reduction system to recover oxygen from CO2. In order to improve the equivalent system mass of Bosch systems, we seek to design and test a "Series Bosch" system in which two reactors in series are optimized for the two steps of the reaction, as well as to explore the use of in situ materials as carbon deposition catalysts. Here we report recent developments in this effort including assembly and initial testing of a Reverse Water-Gas Shift reactor (RWGSr) and initial testing of two gas separation membranes. The RWGSr was sized to reduce CO2 produced by a crew of four to carbon monoxide as the first stage in a Series Bosch system. The gas separation membranes, necessary to recycle unreacted hydrogen and CO2, were similarly sized. Additionally, we report results of preliminary experiments designed to determine the catalytic properties of Martian and Lunar regolith simulant for the carbon deposition step.

Short-wave infrared reflectance investigation of sites of paleobiological interest: applications for Mars exploration.

PubMed

Brown, Adrian; Walter, Malcolm; Cudahy, Thomas

2004-01-01

Rover missions to the rocky bodies of the Solar System and especially to Mars require lightweight, portable instruments that use minimal power, require no sample preparation, and provide suitably diagnostic mineralogical information to an Earth-based exploration team. Short-wave infrared (SWIR) spectroscopic instruments such as the Portable Infrared Mineral Analyser (PIMA, Integrated Spectronics Pty Ltd., Baulkham Hills, NSW, Australia) fulfill all these requirements. We describe an investigation of a possible Mars analogue site using a PIMA instrument. A survey was carried out on the Strelley Pool Chert, an outcrop of stromatolitic, silicified Archean carbonate and clastic succession in the Pilbara Craton, interpreted as being modified by hydrothermal processes. The results of this study demonstrate the capability of SWIR techniques to add significantly to the geological interpretation of such hydrothermally altered outcrops. Minerals identified include dolomite, white micas such as illite-muscovite, and chlorite. In addition, the detection of pyrophyllite in a bleached and altered unit directly beneath the succession suggests acidic, sulfur-rich hydrothermal activity may have interacted with the silicified sediments of the Strelley Pool Chert.

Acute treatment of migraine headaches.

PubMed

Taylor, Frederick R

2010-04-01

Optimum acute treatment of migraine requires prevention of headache as a top priority. Recognition of the multitude of migraine presentations, the frequency of total headache attacks, and number of days of headache disability are critical. Successful treatment requires excellent patient-clinician communication enhancing confidence and mutual trust based on patient needs and preferences. Optimum management of acute migraine nearly always requires pharmacologic treatment for rapid resolution. Migraine-specific triptans, dihydroergotamine, and several antiinflammatories have substantial empirical clinical efficacy. Older nonspecific drugs, particularly butalbital and opioids, contribute to medication overuse headache and are to be avoided. Clinicians should utilize evidence-based acute migraine-specific therapy stressing the imperative acute treatment goal of early intervention, but not too often with the correct drug, formulation, and dose. This therapy needs to provide cost-effective fast results, meaningful to the patient while minimizing the need for additional drugs. Migraine-ACT evaluates 2-hour pain freedom with return to normal function, comfort with treatment, and consistency of response. Employ a thoroughly educated patient, formulary, testimonials, stratification, and rational cotherapy against the race to central sensitization for optimum outcomes. Thieme Medical Publishers.

Requirement for Dot1l in murine postnatal hematopoiesis and leukemogenesis by MLL translocation

PubMed Central

Jo, Stephanie Y.; Granowicz, Eric M.; Maillard, Ivan; Thomas, Dafydd

2011-01-01

Disruptor of telomeric silencing 1-like (Dot1l) is a histone 3 lysine 79 methyltransferase. Studies of constitutive Dot1l knockout mice show that Dot1l is essential for embryonic development and prenatal hematopoiesis. DOT1L also interacts with translocation partners of Mixed Lineage Leukemia (MLL) gene, which is commonly translocated in human leukemia. However, the requirement of Dot1l in postnatal hematopoiesis and leukemogenesis of MLL translocation proteins has not been conclusively shown. With a conditional Dot1l knockout mouse model, we examined the consequences of Dot1l loss in postnatal hematopoiesis and MLL translocation leukemia. Deletion of Dot1l led to pancytopenia and failure of hematopoietic homeostasis, and Dot1l-deficient cells minimally reconstituted recipient bone marrow in competitive transplantation experiments. In addition, MLL-AF9 cells required Dot1l for oncogenic transformation, whereas cells with other leukemic oncogenes, such as Hoxa9/Meis1 and E2A-HLF, did not. These findings illustrate a crucial role of Dot1l in normal hematopoiesis and leukemogenesis of specific oncogenes. PMID:21398221

DOUBLE SHELL TANK (DST) INTEGRITY PROJECT HIGH LEVEL WASTE CHEMISTRY OPTIMIZATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

WASHENFELDER DJ

2008-01-22

The U.S. Department of Energy's Office (DOE) of River Protection (ORP) has a continuing program for chemical optimization to better characterize corrosion behavior of High-Level Waste (HLW). The DOE controls the chemistry in its HLW to minimize the propensity of localized corrosion, such as pitting, and stress corrosion cracking (SCC) in nitrate-containing solutions. By improving the control of localized corrosion and SCC, the ORP can increase the life of the Double-Shell Tank (DST) carbon steel structural components and reduce overall mission costs. The carbon steel tanks at the Hanford Site are critical to the mission of safely managing stored HLWmore » until it can be treated for disposal. The DOE has historically used additions of sodium hydroxide to retard corrosion processes in HLW tanks. This also increases the amount of waste to be treated. The reactions with carbon dioxide from the air and solid chemical species in the tank continually deplete the hydroxide ion concentration, which then requires continued additions. The DOE can reduce overall costs for caustic addition and treatment of waste, and more effectively utilize waste storage capacity by minimizing these chemical additions. Hydroxide addition is a means to control localized and stress corrosion cracking in carbon steel by providing a passive environment. The exact mechanism that causes nitrate to drive the corrosion process is not yet clear. The SCC is less of a concern in the newer stress relieved double shell tanks due to reduced residual stress. The optimization of waste chemistry will further reduce the propensity for SCC. The corrosion testing performed to optimize waste chemistry included cyclic potentiodynamic volarization studies. slow strain rate tests. and stress intensity factor/crack growth rate determinations. Laboratory experimental evidence suggests that nitrite is a highly effective:inhibitor for pitting and SCC in alkaline nitrate environments. Revision of the corrosion control strategies to a nitrite-based control, where there is no constant depletion mechanism as with hydroxide, should greatly enhance tank lifetime, tank space availability, and reduce downstream reprocessing costs by reducing chemical addition to the tanks.« less

OxMaR: open source free software for online minimization and randomization for clinical trials.

PubMed

O'Callaghan, Christopher A

2014-01-01

Minimization is a valuable method for allocating participants between the control and experimental arms of clinical studies. The use of minimization reduces differences that might arise by chance between the study arms in the distribution of patient characteristics such as gender, ethnicity and age. However, unlike randomization, minimization requires real time assessment of each new participant with respect to the preceding distribution of relevant participant characteristics within the different arms of the study. For multi-site studies, this necessitates centralized computational analysis that is shared between all study locations. Unfortunately, there is no suitable freely available open source or free software that can be used for this purpose. OxMaR was developed to enable researchers in any location to use minimization for patient allocation and to access the minimization algorithm using any device that can connect to the internet such as a desktop computer, tablet or mobile phone. The software is complete in itself and requires no special packages or libraries to be installed. It is simple to set up and run over the internet using online facilities which are very low cost or even free to the user. Importantly, it provides real time information on allocation to the study lead or administrator and generates real time distributed backups with each allocation. OxMaR can readily be modified and customised and can also be used for standard randomization. It has been extensively tested and has been used successfully in a low budget multi-centre study. Hitherto, the logistical difficulties involved in minimization have precluded its use in many small studies and this software should allow more widespread use of minimization which should lead to studies with better matched control and experimental arms. OxMaR should be particularly valuable in low resource settings.

Interferences from blood collection tube components on clinical chemistry assays

PubMed Central

Bowen, Raffick A.R.; Remaley, Alan T.

2014-01-01

Improper design or use of blood collection devices can adversely affect the accuracy of laboratory test results. Vascular access devices, such as catheters and needles, exert shear forces during blood flow, which creates a predisposition to cell lysis. Components from blood collection tubes, such as stoppers, lubricants, surfactants, and separator gels, can leach into specimens and/or adsorb analytes from a specimen; special tube additives may also alter analyte stability. Because of these interactions with blood specimens, blood collection devices are a potential source of pre-analytical error in laboratory testing. Accurate laboratory testing requires an understanding of the complex interactions between collection devices and blood specimens. Manufacturers, vendors, and clinical laboratorians must consider the pre-analytical challenges in laboratory testing. Although other authors have described the effects of endogenous substances on clinical assay results, the effects/impact of blood collection tube additives and components have not been well systematically described or explained. This review aims to identify and describe blood collection tube additives and their components and the strategies used to minimize their effects on clinical chemistry assays. PMID:24627713

Improving Growth and Productivity of Oleiferous Brassicas under Changing Environment: Significance of Nitrogen and Sulphur Nutrition, and Underlying Mechanisms

PubMed Central

Anjum, Naser A.; Gill, Sarvajeet S.; Umar, Shahid; Ahmad, Iqbal; Duarte, Armando C.; Pereira, Eduarda

2012-01-01

Mineral nutrients are the integral part of the agricultural systems. Among important plant nutrients, nitrogen (N) and sulphur (S) are known essential elements for growth, development, and various physiological functions in plants. Oleiferous brassicas (rapeseed and mustard) require higher amounts of S in addition to N for optimum growth and yield. Therefore, balancing S-N fertilization, optimization of nutrient replenishment, minimization of nutrient losses to the environment, and the concept of coordination in action between S and N could be a significant strategy for improvement of growth and productivity of oleiferous brassicas. Additionally, positive interaction between S and N has been reported to be beneficial for various aspects of oilseed brassicas. The current paper updates readers on the significance of N and S for the improvement of plant growth, development, and productivity in detail. In addition, S-N nutrition-mediated control of major plant antioxidant defense system components involved in the removal and/or metabolism of stress-induced/generated reactive oxygen species in plants (hence, the control of plant growth, development, and productivity) has been overviewed. PMID:22629181

High resolution techno-ecological modeling of a bioenergy landscape to identify climate mitigation opportunities in cellulosic ethanol production

USDA-ARS?s Scientific Manuscript database

Meeting current biofuel mandates or creating future carbon-negative biopower systems requires feedstocks be sourced in sufficient quantities at low cost and with minimal environmental impact. Cultivating perennial grasses on low-quality lands is a promising feedstock supply strategy minimizing on-...

24 CFR 42.325 - Residential antidisplacement and relocation assistance plan.

Code of Federal Regulations, 2012 CFR

2012-04-01

..., Department of Housing and Urban Development DISPLACEMENT, RELOCATION ASSISTANCE, AND REAL PROPERTY... minimize displacement of persons as a result of assisted activities. The State may require the unit of... objectives of the program, as provided in parts 92 and 570 of this title, to minimize the displacement of...

24 CFR 42.325 - Residential antidisplacement and relocation assistance plan.

Code of Federal Regulations, 2014 CFR

2014-04-01

..., Department of Housing and Urban Development DISPLACEMENT, RELOCATION ASSISTANCE, AND REAL PROPERTY... minimize displacement of persons as a result of assisted activities. The State may require the unit of... objectives of the program, as provided in parts 92 and 570 of this title, to minimize the displacement of...

24 CFR 42.325 - Residential antidisplacement and relocation assistance plan.

Code of Federal Regulations, 2013 CFR

2013-04-01

..., Department of Housing and Urban Development DISPLACEMENT, RELOCATION ASSISTANCE, AND REAL PROPERTY... minimize displacement of persons as a result of assisted activities. The State may require the unit of... objectives of the program, as provided in parts 92 and 570 of this title, to minimize the displacement of...

24 CFR 42.325 - Residential antidisplacement and relocation assistance plan.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., Department of Housing and Urban Development DISPLACEMENT, RELOCATION ASSISTANCE, AND REAL PROPERTY... minimize displacement of persons as a result of assisted activities. The State may require the unit of... objectives of the program, as provided in parts 92 and 570 of this title, to minimize the displacement of...

24 CFR 42.325 - Residential antidisplacement and relocation assistance plan.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., Department of Housing and Urban Development DISPLACEMENT, RELOCATION ASSISTANCE, AND REAL PROPERTY... minimize displacement of persons as a result of assisted activities. The State may require the unit of... objectives of the program, as provided in parts 92 and 570 of this title, to minimize the displacement of...

Minimal Competency Exam Program.

ERIC Educational Resources Information Center

Griffith, E. H.

The high school minimal competency examination described in this document is part one of a three-part program that requires that all students satisfactorily complete tests in reading, language arts, and mathematics prior to receiving a high school diploma. The document outlines the test development and assessment program and describes the plan for…

40 CFR 230.5 - General procedures to be followed.

Code of Federal Regulations, 2013 CFR

2013-07-01

....5 Section 230.5 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) OCEAN DUMPING... discharge in § 230.10(a) through (d), the measures to mimimize adverse impact of subpart H, and the required... minimize the environmental impact of the discharge, based upon the specialized methods of minimization of...

47 CFR 90.403 - General operating requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... communications in progress and such other measures as may be necessary to minimize the potential for causing... 90.403 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) SAFETY AND SPECIAL RADIO SERVICES PRIVATE LAND MOBILE RADIO SERVICES Operating Requirements § 90.403 General operating requirements...

SU-F-T-35: Optimization of Bladder and Rectal Doses Using a Multi-Lumen Intracavitary Applicator for Gynecological Brachytherapy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Laoui, S; Dietrich, S; Sehgal, V

2016-06-15

Purpose: Radiation dose delivery for endometrial cancer using HDR techniques is limited by dose to bladder and rectum. A dosimetric study was performed using Varian Capri vaginal brachytherapy applicator to determine the optimal channel configuration which minimizes dose to bladder and rectum, while providing good target coverage. Methods: A total of 17 patients, 63 plans clinically delivered, and 252 simulated plans using Varian BrachyVision planning system were generated to investigate optimal channel configuration which results in minimum dose to bladder and rectum while providing adequate target coverage. The Capri applicator consists of 13 lumens arranged in two concentric rings, onemore » central lumen and six lumens per ring. Manual dose shaping is invariably required to lower the dose to critical organs. Three-dimensional plans were simulated for 4 channel arrangements, all 13 channels, channel 12 o’clock (close to bladder) and 6 o’clock (close to rectum) deactivated, central channel deactivated, and central channel in addition to 12 o’clock and 6 o’clock deactivated. A relationship between V100, the volume that receives the prescribed dose, and the amount of curie-seconds required to deliver it, was established. Results: Using all 13 channels results in maximum dose to bladder and rectum. Deactivating central channel in addition to 12 o’clock and 6 o’clock resulted in minimizing bladder and rectum doses but compromised target coverage. The relationship between V100, the volume that receives the prescribed dose, and the curie seconds was found to be linear. Conclusion: Deactivating channels 12 o’clock and 6 o’clock was shown to be the optimal configuration leading to minimum dose to bladder and rectum without compromising target coverage. The linear relationship between V100 and the curie- seconds can be used as a verification parameter.« less

Operations mission planner beyond the baseline

NASA Technical Reports Server (NTRS)

Biefeld, Eric; Cooper, Lynne

1991-01-01

The scheduling of Space Station Freedom must satisfy four major requirements. It must ensure efficient housekeeping operations, maximize the collection of science, respond to changes in tasking and available resources, and accommodate the above changes in a manner that minimizes disruption of the ongoing operations of the station. While meeting these requirements the scheduler must cope with the complexity, scope, and flexibility of SSF operations. This requires the scheduler to deal with an astronomical number of possible schedules. The Operations Mission Planner (OMP) is centered around minimally disruptive replanning and the use of heuristics limit search in scheduling. OMP has already shown several artificial intelligence based scheduling techniques such as Interleaved Iterative Refinement and Bottleneck Identification using Process Chronologies.

Cross-species 3D virtual reality toolbox for visual and cognitive experiments.

PubMed

Doucet, Guillaume; Gulli, Roberto A; Martinez-Trujillo, Julio C

2016-06-15

Although simplified visual stimuli, such as dots or gratings presented on homogeneous backgrounds, provide strict control over the stimulus parameters during visual experiments, they fail to approximate visual stimulation in natural conditions. Adoption of virtual reality (VR) in neuroscience research has been proposed to circumvent this problem, by combining strict control of experimental variables and behavioral monitoring within complex and realistic environments. We have created a VR toolbox that maximizes experimental flexibility while minimizing implementation costs. A free VR engine (Unreal 3) has been customized to interface with any control software via text commands, allowing seamless introduction into pre-existing laboratory data acquisition frameworks. Furthermore, control functions are provided for the two most common programming languages used in visual neuroscience: Matlab and Python. The toolbox offers milliseconds time resolution necessary for electrophysiological recordings and is flexible enough to support cross-species usage across a wide range of paradigms. Unlike previously proposed VR solutions whose implementation is complex and time-consuming, our toolbox requires minimal customization or technical expertise to interface with pre-existing data acquisition frameworks as it relies on already familiar programming environments. Moreover, as it is compatible with a variety of display and input devices, identical VR testing paradigms can be used across species, from rodents to humans. This toolbox facilitates the addition of VR capabilities to any laboratory without perturbing pre-existing data acquisition frameworks, or requiring any major hardware changes. Copyright © 2016 Z. All rights reserved.

A comparison of 2 cesarean section methods, modified Misgav-Ladach and Pfannenstiel-Kerr: A randomized controlled study.

PubMed

Şahin, Nur; Genc, Mine; Turan, Gülüzar Arzu; Kasap, Esin; Güçlü, Serkan

2018-03-13

The modified Misgav-Ladach method (MML) is a minimally invasive cesarean section procedure compared with the classic Pfannenstiel-Kerr (PK) method. The aim of the study was to compare the MML method and the PK method in terms of intraoperative and short-term postoperative outcomes. This prospective, randomized controlled trial involved 252 pregnant women scheduled for primary emergency or elective cesarean section between October, 2014 and July, 2015. The primary outcome measures were the duration of surgery, extraction time, Apgar score, blood loss, wound complications, and number of sutures used. Secondary outcome measures were the wound infection, time of bowel restitution, visual analogue scale (VAS) scores at 6 h and 24 h after the operation, limitations in movement, and analgesic requirements. At 6 weeks after surgery, the patients were evaluated regarding late complications. There was a significant reduction in total operating and extraction time in the MML group (p < 0.001). Limitations in movement were lower at 24 h after the MML operation, and less analgesic was required in the MML group. There was no difference between the 2 groups in terms of febrile morbidity or the duration of hospitalization. At 6 weeks after the operation, no complaints and no additional complications from the surgery were noted. The MML method is a minimally invasive cesarean section. In the future, as surgeons' experience increases, MML will likely be chosen more often than the classic PK method.

Cost-minimization Analysis of the Management of Acute Achilles Tendon Rupture.

PubMed

Truntzer, Jeremy N; Triana, Brian; Harris, Alex H S; Baker, Laurence; Chou, Loretta; Kamal, Robin N

2017-06-01

Outcomes of nonsurgical management of acute Achilles tendon rupture have been demonstrated to be noninferior to those of surgical management. We performed a cost-minimization analysis of surgical and nonsurgical management of acute Achilles tendon rupture. We used a claims database to identify patients who underwent surgical (n = 1,979) and nonsurgical (n = 3,065) management of acute Achilles tendon rupture and compared overall costs of treatment (surgical procedure, follow-up care, physical therapy, and management of complications). Complication rates were also calculated. Patients were followed for 1 year after injury. Average treatment costs in the year after initial diagnosis were higher for patients who underwent initial surgical treatment than for patients who underwent nonsurgical treatment ($4,292 for surgical treatment versus $2,432 for nonsurgical treatment; P < 0.001). However, surgical treatment required fewer office visits (4.52 versus 10.98; P < 0.001) and less spending on physical therapy ($595 versus $928; P < 0.001). Rates of rerupture requiring subsequent treatment (2.1% versus 2.4%; P = 0.34) and additional costs ($2,950 versus $2,515; P = 0.34) were not significantly different regardless whether initial treatment was surgical or nonsurgical. In both cohorts, management of complications contributed to approximately 5% of the total cost. From the payer's perspective, the overall costs of nonsurgical management of acute Achilles tendon rupture were significantly lower than the overall costs of surgical management. III, Economic Decision Analysis.

10 CFR 850.25 - Exposure reduction and minimization.

Code of Federal Regulations, 2010 CFR

2010-01-01

... § 850.25 Exposure reduction and minimization. (a) The responsible employer must ensure that no worker is exposed above the exposure limit prescribed in § 850.22. (b) The responsible employer must, in addition... described in the responsible employer's CBDPP and must include: (i) Annual goals for exposure reduction and...

21 CFR 50.51 - Clinical investigations not involving greater than minimal risk.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Clinical investigations not involving greater than... HUMAN SERVICES GENERAL PROTECTION OF HUMAN SUBJECTS Additional Safeguards for Children in Clinical Investigations § 50.51 Clinical investigations not involving greater than minimal risk. Any clinical...

Minimalism through intraoperative functional mapping.

PubMed

Berger, M S

1996-01-01

Intraoperative stimulation mapping may be used to avoid unnecessary risk to functional regions subserving language and sensori-motor pathways. Based on the data presented here, language localization is variable in the entire population, with only certainty existing for the inferior frontal region responsible for motor speech. Anatomical landmarks such as the anterior temporal tip for temporal lobe language sites and the posterior aspect of the lateral sphenoid wing for the frontal lobe language zones are unreliable in avoiding postoperative aphasias. Thus, individual mapping to identify essential language sites has the greatest likelihood of avoiding permanent deficits in naming, reading, and motor speech. In a similar approach, motor and sensory pathways from the cortex and underlying white matter may be reliably stimulated and mapped in both awake and asleep patients. Although these techniques require an additional operative time and equipment nominally priced, the result is often gratifying, as postoperative morbidity has been greatly reduced in the process of incorporating these surgical strategies. The patients quality of life is improved in terms of seizure control, with or without antiepileptic drugs. This avoids having to perform a second costly operative procedure, which is routinely done when extraoperative stimulation and recording is done via subdural grids. In addition, an aggressive tumor resection at the initial operation lengthens the time to tumor recurrence and often obviates the need for a subsequent reoperation. Thus, intraoperative functional mapping may be best alluded to as a surgical technique that results in "minimalism in the long term".

Multidisciplinary acute care research organization (MACRO): if you build it, they will come.

PubMed

Early, Barbara J; Huang, David T; Callaway, Clifton W; Zenati, Mazen; Angus, Derek C; Gunn, Scott R; Yealy, Donald M; Unikel, Daniel; Billiar, Timothy R; Peitzman, Andrew B; Sperry, Jason L

2013-07-01

Clinical research will increasingly play a core role in the evolution and growth of acute care surgery program development across the country. What constitutes an efficient and effective clinical research infrastructure in the current fiscal and academic environment remains obscure. We sought to characterize the effects of implementation of a multidisciplinary acute care research organization (MACRO) at a busy tertiary referral university setting. In 2008, to minimize redundancy and cost as well as to maximize existing resources promoting acute care research, MACRO was created, unifying clinical research infrastructure among the Departments of Critical Care Medicine, Emergency Medicine, and Surgery. During the periods 2008 to 2012, we performed a retrospective analysis and determined volume of clinical studies, patient enrollment for both observational and interventional trials, and staff growth since MACRO's origination and characterized changes over time. From 2008 to 2011, the volume of patients enrolled in clinical studies, which MACRO facilitates has significantly increased more than 300%. The percentage of interventional/observational trials has remained stable during the same period (50-60%). Staff has increased from 6 coordinators to 10, with an additional 15 research associates allowing 24/7 service. With this significant growth, MACRO has become financially self-sufficient, and additional outside departments now seek MACRO's services. Appropriate organization of acute care clinical research infrastructure minimizes redundancy and can promote sustainable, efficient growth in the current academic environment. Further studies are required to determine if similar models can be successful at other acute care surgery programs.

DE-FG02-96ER20226 FinalTechnicalReport

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lidstrom, M E

In the future, environmental concerns will mandate that manufacturing processes shift towards the use of renewable resources and the minimization of wastes, especially hazardous wastes. One-carbon compounds are of interest as feedstocks for synthesis of chemicals and materials, because they represent a relatively inexpensive, abundant and renewable resource. In addition, the environmentally-benign characteristics of microbial processes make them of interest as part of a long-term waste-minimization strategy for industry. The concept that methylotrophic bacteria could serve as non-polluting multistage catalysts to generate chemicals and materials using C1 compounds as feedstocks is a highly attractive one. In order to develop productionmore » strains of methylotrophs, it is necessary to understand and manipulate central methylotrophic pathways. One of the most important of these is the methanol oxidation, or Mox system. In this project, we are studying the promoters and transcriptional regulation of this 25-gene system in Methylobacterium extorquens AM1, a facultative methanol-utilizer. We have addressed the significance of a hexanucleotide sequence upstream of all mox promoters and have shown that it is required for activity of these promoters using both deletion and mutational analyses. In addition, we have identified a putative hairpin structure in the RNA leader region of the mxa promoter that is also essential for transcriptional, and have assessed the mechanism of action of this regulatory region. This work is providing the foundation for development of methylotrophic strains to convert methanol into higher value added products.« less

Characterization of carbon fiber polymer matrix composites subjected to simultaneous application of electric current pulse and low velocity impact

NASA Astrophysics Data System (ADS)

Hart, Robert James

2011-12-01

The use of composite materials in aerospace, electronics, and wind industries has become increasingly common, and these composite components are required to carry mechanical, electrical, and thermal loads simultaneously. A unique property of carbon fiber composites is that when an electric current is applied to the specimen, the mechanical strength of the specimen increases. Previous studies have shown that the higher the electric current, the greater the increase in impact strength. However, as current passes through the composite, heat is generated through Joule heating. This Joule heating can cause degradation of the composite and thus a loss in strength. In order to minimize the negative effects of heating, it is desired to apply a very high current for a very short duration of time. This thesis investigated the material responses of carbon fiber composite plates subjected to electrical current pulse loads of up to 1700 Amps. For 32 ply unidirectional IM7/977-3 specimens, the peak impact load and absorbed energy increased slightly with the addition of a current pulse at the time of an impact event. In 16 ply cross-ply IM7/977-2 specimens, the addition of the current pulse caused detrimental effects due to electrical arcing at the interface between the composite and electrodes. Further refinement of the experimental setup should minimize the risk of electrical arcing and should better elucidate the effects of a current pulse on the impact strength of the specimens.

Chance-constrained multi-objective optimization of groundwater remediation design at DNAPLs-contaminated sites using a multi-algorithm genetically adaptive method.

PubMed

Ouyang, Qi; Lu, Wenxi; Hou, Zeyu; Zhang, Yu; Li, Shuai; Luo, Jiannan

2017-05-01

In this paper, a multi-algorithm genetically adaptive multi-objective (AMALGAM) method is proposed as a multi-objective optimization solver. It was implemented in the multi-objective optimization of a groundwater remediation design at sites contaminated by dense non-aqueous phase liquids. In this study, there were two objectives: minimization of the total remediation cost, and minimization of the remediation time. A non-dominated sorting genetic algorithm II (NSGA-II) was adopted to compare with the proposed method. For efficiency, the time-consuming surfactant-enhanced aquifer remediation simulation model was replaced by a surrogate model constructed by a multi-gene genetic programming (MGGP) technique. Similarly, two other surrogate modeling methods-support vector regression (SVR) and Kriging (KRG)-were employed to make comparisons with MGGP. In addition, the surrogate-modeling uncertainty was incorporated in the optimization model by chance-constrained programming (CCP). The results showed that, for the problem considered in this study, (1) the solutions obtained by AMALGAM incurred less remediation cost and required less time than those of NSGA-II, indicating that AMALGAM outperformed NSGA-II. It was additionally shown that (2) the MGGP surrogate model was more accurate than SVR and KRG; and (3) the remediation cost and time increased with the confidence level, which can enable decision makers to make a suitable choice by considering the given budget, remediation time, and reliability. Copyright © 2017 Elsevier B.V. All rights reserved.

Optimal Black Start Resource Allocation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Qiu, Feng; Wang, Jianhui; Chen, Chen

The restoration of the bulk power system after a partial or complete blackout relies on black-start (BS) resources. To prepare for system restoration, it is important to procure the right amount of BS resources at the right locations in the grid so that the total restoration time can be minimized. Achieving this goal requires that resource procurement planning takes the restoration process into account. In this study, we integrate the BS resource procurement decision with a restoration planning model and develop an optimization model that produces a minimal cost procurement plan that satisfies the restoration time requirement.

Cleaning Genesis Sample Return Canister for Flight: Lessons for Planetary Sample Return

NASA Technical Reports Server (NTRS)

Allton, J. H.; Hittle, J. D.; Mickelson, E. T.; Stansbery, Eileen K.

2016-01-01

Sample return missions require chemical contamination to be minimized and potential sources of contamination to be documented and preserved for future use. Genesis focused on and successfully accomplished the following: - Early involvement provided input to mission design: a) cleanable materials and cleanable design; b) mission operation parameters to minimize contamination during flight. - Established contamination control authority at a high level and developed knowledge and respect for contamination control across all institutions at the working level. - Provided state-of-the-art spacecraft assembly cleanroom facilities for science canister assembly and function testing. Both particulate and airborne molecular contamination was minimized. - Using ultrapure water, cleaned spacecraft components to a very high level. Stainless steel components were cleaned to carbon monolayer levels (10 (sup 15) carbon atoms per square centimeter). - Established long-term curation facility Lessons learned and areas for improvement, include: - Bare aluminum is not a cleanable surface and should not be used for components requiring extreme levels of cleanliness. The problem is formation of oxides during rigorous cleaning. - Representative coupons of relevant spacecraft components (cut from the same block at the same time with identical surface finish and cleaning history) should be acquired, documented and preserved. Genesis experience suggests that creation of these coupons would be facilitated by specification on the engineering component drawings. - Component handling history is critical for interpretation of analytical results on returned samples. This set of relevant documents is not the same as typical documentation for one-way missions and does include data from several institutions, which need to be unified. Dedicated resources need to be provided for acquiring and archiving appropriate documents in one location with easy access for decades. - Dedicated, knowledgeable contamination control oversight should be provided at sites of fabrication and integration. Numerous excellent Genesis chemists and analytical facilities participated in the contamination oversight; however, additional oversight at fabrication sites would have been helpful.

Minimizing marker mass and handling time when attaching radio-transmitters and geolocators to small songbirds

USGS Publications Warehouse

Streby, Henry M.; McAllister, Tara L.; Peterson, Sean M.; Kramer, Gunnar R.; Lehman, Justin A.; Andersen, David E.

2015-01-01

Radio-transmitters and light-level geolocators are currently small enough for use on songbirds weighing <15 g. Various methods are used to attach these markers to larger songbirds, but with small birds it becomes especially important to minimize marker mass and bird handling time. Here, we offer modifications to harness materials and marker preparation for transmitters and geolocators, and we describe deployment methods that can be safely completed in 20–60 s per bird. We describe a 0.5-mm elastic sewing thread harness for radio-transmitters that allows nestlings, fledglings, and adults to be marked with the same harness size and reliably falls off to avoid poststudy effects. We also describe a 0.5-mm jewelry cord harness for geolocators that provides a firm fit for >1 yr. Neither harness type requires plastic or metal tubes, rings, or other attachment fixtures on the marker, nor do they require crimping beads, epoxy, scissors, or tying knots while handling birds. Both harnesses add 0.03 g to the mass of markers for small wood-warblers (Parulidae). This minimal additional mass is offset by trimming transmitter antennas or geolocator connection nodes, resulting in no net mass gain for transmitters and 0.02 g added for geolocators compared with conventional harness methods that add >0.40 g. We and others have used this transmitter attachment method with several small songbird species, with no effects on adult and fledgling behavior and survival. We have used this geolocator attachment method on 9-g wood-warblers with no effects on return rates, return dates, territory fidelity, and body mass. We hope that these improvements to the design and deployment of the leg-loop harness method will enable the safe and successful use of these markers, and eventually GPS and other tags, on similarly small songbirds.

Environmental Defense Fund Oil and Gas Methane Studies: Principles for Collaborating with Industry Partners while Maintaining Scientific Objectivity

NASA Astrophysics Data System (ADS)

Hamburg, S.

2016-12-01

Environmental Defense Fund (EDF) launched a series of 16 research studies in 2012 to quantify methane emissions from the U.S. oil and gas (O&G) supply chain. In addition to EDF's funding from philanthropic individuals and foundations and in-kind contributions from universities, over forty O&G companies contributed money to the studies. For a subset of studies that required partner companies to provide site access to measure their equipment, five common principles were followed to assure that research was objective and scientifically rigorous. First, academic scientists were selected as principal investigators (PIs) to lead the studies. In line with EDF's policy of not accepting money from corporate partners, O&G companies provided funding directly to academic PIs. Technical work groups and steering committees consisting of EDF and O&G partner staff advised the PIs in the planning and implementation of research, but PIs had the final authority in scientific decisions including publication content. Second, scientific advisory panels of independent experts advised the PIs in the study design, data analysis, and interpretation. Third, studies employed multiple methodologies when possible, including top-down and bottom-up measurements. This helped overcome the limitations of individual approaches to decrease the uncertainty of emission estimates and minimize concerns with data being "cherry-picked". Fourth, studies were published in peer-reviewed journals to undergo an additional round of independent review. Fifth, transparency of data was paramount. Study data were released after publication, although operator and site names of individual data points were anonymized to ensure transparency and allow independent analysis. Following these principles allowed an environmental organization, O&G companies, and academic scientists to collaborate in scientific research while minimizing conflicts of interest. This approach can serve as a model for a scientifically rigorous process minimally influenced by study partners.

Planning additional drilling campaign using two-space genetic algorithm: A game theoretical approach

NASA Astrophysics Data System (ADS)

Kumral, Mustafa; Ozer, Umit

2013-03-01

Grade and tonnage are the most important technical uncertainties in mining ventures because of the use of estimations/simulations, which are mostly generated from drill data. Open pit mines are planned and designed on the basis of the blocks representing the entire orebody. Each block has different estimation/simulation variance reflecting uncertainty to some extent. The estimation/simulation realizations are submitted to mine production scheduling process. However, the use of a block model with varying estimation/simulation variances will lead to serious risk in the scheduling. In the medium of multiple simulations, the dispersion variances of blocks can be thought to regard technical uncertainties. However, the dispersion variance cannot handle uncertainty associated with varying estimation/simulation variances of blocks. This paper proposes an approach that generates the configuration of the best additional drilling campaign to generate more homogenous estimation/simulation variances of blocks. In other words, the objective is to find the best drilling configuration in such a way as to minimize grade uncertainty under budget constraint. Uncertainty measure of the optimization process in this paper is interpolation variance, which considers data locations and grades. The problem is expressed as a minmax problem, which focuses on finding the best worst-case performance i.e., minimizing interpolation variance of the block generating maximum interpolation variance. Since the optimization model requires computing the interpolation variances of blocks being simulated/estimated in each iteration, the problem cannot be solved by standard optimization tools. This motivates to use two-space genetic algorithm (GA) approach to solve the problem. The technique has two spaces: feasible drill hole configuration with minimization of interpolation variance and drill hole simulations with maximization of interpolation variance. Two-space interacts to find a minmax solution iteratively. A case study was conducted to demonstrate the performance of approach. The findings showed that the approach could be used to plan a new drilling campaign.

Valuation of OSA process and folic acid addition as excess sludge minimization alternatives applied in the activated sludge process.

PubMed

Martins, C L; Velho, V F; Ramos, S R A; Pires, A S C D; Duarte, E C N F A; Costa, R H R

2016-01-01

The aim of this study was to investigate the ability of the oxic-settling-anaerobic (OSA)-process and the folic acid addition applied in the activated sludge process to reduce the excess sludge production. The study was monitored during two distinct periods: activated sludge system with OSA-process, and activated sludge system with folic acid addition. The observed sludge yields (Yobs) were 0.30 and 0.08 kgTSS kg(-1) chemical oxygen demand (COD), control phase and OSA-process (period 1); 0.33 and 0.18 kgTSS kg(-1) COD, control phase and folic acid addition (period 2). The Yobs decreased by 73 and 45% in phases with the OSA-process and folic acid addition, respectively, compared with the control phases. The sludge minimization alternatives result in a decrease in excess sludge production, without negatively affecting the performance of the effluent treatment.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kolda, Christopher

In this talk, I review recent work on using a generalization of the Next-to-Minimal Supersymmetric Standard Model (NMSSM), called the Singlet-extended Minimal Supersymmetric Standard Model (SMSSM), to raise the mass of the Standard Model-like Higgs boson without requiring extremely heavy top squarks or large stop mixing. In so doing, this model solves the little hierarchy problem of the minimal model (MSSM), at the expense of leaving the {mu}-problem of the MSSM unresolved. This talk is based on work published in Refs. [1, 2, 3].

Chi-squared and C statistic minimization for low count per bin data

NASA Astrophysics Data System (ADS)

Nousek, John A.; Shue, David R.

1989-07-01

Results are presented from a computer simulation comparing two statistical fitting techniques on data samples with large and small counts per bin; the results are then related specifically to X-ray astronomy. The Marquardt and Powell minimization techniques are compared by using both to minimize the chi-squared statistic. In addition, Cash's C statistic is applied, with Powell's method, and it is shown that the C statistic produces better fits in the low-count regime than chi-squared.

Chi-squared and C statistic minimization for low count per bin data. [sampling in X ray astronomy

NASA Technical Reports Server (NTRS)

Nousek, John A.; Shue, David R.

1989-01-01

Results are presented from a computer simulation comparing two statistical fitting techniques on data samples with large and small counts per bin; the results are then related specifically to X-ray astronomy. The Marquardt and Powell minimization techniques are compared by using both to minimize the chi-squared statistic. In addition, Cash's C statistic is applied, with Powell's method, and it is shown that the C statistic produces better fits in the low-count regime than chi-squared.

The use of CVD diamond burs for ultraconservative cavity preparations: a report of two cases.

PubMed

Carvalho, Carlos Augusto R; Fagundes, Ticiane C; Barata, Terezinha J E; Trava-Airoldi, Vladimir Jesus; Navarro, Maria Fidela L

2007-01-01

During the past decades, scientific developments in cutting instruments have changed the conventional techniques used to remove caries lesions. Ultrasound emerged as an alternative for caries removal since the 1950s. However, the conventional technology for diamond powder aggregation with nickel metallic binders could not withstand ultrasonic power. Around 5 years ago, an alternative approach using chemical vapor deposition (CVD) resulted in synthetic diamond technology. CVD diamond burs are obtained with high adherence of the diamond as a unique stone on the metallic surface with excellent abrading performance. This technology allows for diamond deposition with coalescent granulation in different formats of substrates. When connected to an ultrasonic handpiece, CVD diamond burs become an option for cavity preparation, maximizing preservation of tooth structure. Potential advantages such as reduced noise, minimal damage to the gingival tissue, extended bur durability, improved proximal cavity access, reduced risk of hitting the adjacent tooth resulting from the high inclination angles, and minimal patient's risk of metal contamination. These innovative instruments also potentially eliminate some problems regarding decreased cutting efficiency of conventional diamond burs. This clinical report presents the benefits of using CVD diamond burs coupled with an ultrasonic handpiece in the treatment of incipient caries. CVD diamond burs coupled with an ultrasonic device offer a promising alternative for removal of carious lesions when ultraconservative cavity preparations are required. Additionally, this system provides a less-painful technique for caries removal, with minimal noise.

Reagentless chemiluminescence-based fiber optic sensors for regenerative life support in space

NASA Astrophysics Data System (ADS)

Atwater, James E.; Akse, James R.; DeHart, Jeffrey; Wheeler, Richard R., Jr.

1995-04-01

The initial feasibility demonstration of a reagentless chemiluminescence based fiber optic sensor technology for use in advanced regenerative life support applications in space and planetary outposts is described. The primary constraints for extraterrestrial deployment of any technology are compatibility with microgravity and hypogravity environments; minimal size, weight, and power consumption; and minimal use of expendables due to the great expense and difficulty inherent to resupply logistics. In the current research, we report the integration of solid state flow through modules for the production of aqueous phase reagents into an integrated system for the detection of important analytes by chemiluminescence, with fiber optic light transmission. By minimizing the need for resupply expendables, the use of solid phase modules makes complex chemical detection schemes practical. For the proof of concept, hydrogen peroxide and glucose were chosen as analytes. The reaction is catalyzed by glucose oxidase, an immobilized enzyme. The aqueous phase chemistry required for sensor operation is implemented using solid phase modules which adjust the pH of the influent stream, catalyze the oxidation of analyte, and provide the controlled addition of the luminophore to the flowing aqueous stream. Precise control of the pH has proven essential for the long-term sustained release of the luminophore. Electrocatalysis is achieved using a controlled potential across gold mesh and gold foil electrodes which undergo periodic polarity reversals. The development and initial characterization of performance of the reagentless fiber optic chemiluminescence sensors are presented in this paper.

Minimizing AED adverse effects: improving quality of life in the interictal state in epilepsy care.

PubMed

St Louis, Erik K; Louis, Erik K

2009-06-01

The goals of epilepsy therapy are to achieve seizure freedom while minimizing adverse effects of treatment. However, producing seizure-freedom is often overemphasized, at the expense of inducing adverse effects of treatment. All antiepileptic drugs (AEDs) have the potential to cause dose-related, "neurotoxic" adverse effects (i.e., drowsiness, fatigue, dizziness, blurry vision, and incoordination). Such adverse effects are common, especially when initiating AED therapy and with polytherapy. Dose-related adverse effects may be obviated in most patients by dose reduction of monotherapy, reduction or elimination of polytherapy, or substituting for a better tolerated AED. Additionally, all older and several newer AEDs have idiosyncratic adverse effects which usually require withdrawal in an affected patient, including serious rash (i.e., Stevens-Johnson Syndrome, toxic epidermal necrolysis), hematologic dyscrasias, hepatotoxicity, teratogenesis in women of child bearing potential, bone density loss, neuropathy, and severe gingival hyperplasia. Unfortunately, occurrence of idiosyncratic AED adverse effects cannot be predicted or, in most cases, prevented in susceptible patients. This article reviews a practical approach for the definition and identification of adverse effects of epilepsy therapies, and reviews the literature demonstrating that adverse effects result in detrimental quality of life in epilepsy patients. Strategies for minimizing AED adverse effects by reduction or elimination of AED polytherapy, appropriately employing drug-sparing therapies, and optimally administering AEDs are outlined, including tenets of AED selection, titration, therapeutic AED laboratory monitoring, and avoidance of chronic idiosyncratic adverse effects.

Surgery of the elderly in emergency room mode. Is there a place for laparoscopy?

PubMed Central

Michalik, Maciej; Lech, Paweł; Zacharz, Krzysztof

2017-01-01

Introduction An important yet difficult problem is qualification for surgery in elderly patients. With age the risk of comorbidities increases – multi-disease syndrome. Elderly patients suffer from frailty syndrome. Many body functions become impaired. All these factors make the elderly patient a major challenge for surgical treatment. Aim Analysis of the possibility of developing the indications and contraindications and the criteria for surgical treatment of the elderly based on our own cases. Discussion whether there is a place for laparoscopy during surgery of the elderly in emergency room (ER) mode. Material and methods The analysis was performed based on seven cases involving surgical treatment of elderly patients who were admitted to the hospital in emergency room mode. The patients were hospitalized in the General and Minimally Invasive Surgery Clinic in Olsztyn in 2016. Results Surgical treatment of elderly patients should be planned with multidisciplinary teams. Geriatric surgery centers should be developed to minimize the risk of overzealous treatment and potential complications. Laparoscopy should always be considered in the case of ER procedures or diagnostics. Conclusions Elderly patients should not be treated as typical adults, but as a separate group of patients requiring special treatment. Due to the existing additional disease in the elderly, the frailty syndrome, any surgical intervention should be minimally invasive. The discussion about therapy should be conducted by a team of specialists from a variety of medical fields. PMID:28694895

Seizure Control in a Computational Model Using a Reinforcement Learning Stimulation Paradigm.

PubMed

Nagaraj, Vivek; Lamperski, Andrew; Netoff, Theoden I

2017-11-01

Neuromodulation technologies such as vagus nerve stimulation and deep brain stimulation, have shown some efficacy in controlling seizures in medically intractable patients. However, inherent patient-to-patient variability of seizure disorders leads to a wide range of therapeutic efficacy. A patient specific approach to determining stimulation parameters may lead to increased therapeutic efficacy while minimizing stimulation energy and side effects. This paper presents a reinforcement learning algorithm that optimizes stimulation frequency for controlling seizures with minimum stimulation energy. We apply our method to a computational model called the epileptor. The epileptor model simulates inter-ictal and ictal local field potential data. In order to apply reinforcement learning to the Epileptor, we introduce a specialized reward function and state-space discretization. With the reward function and discretization fixed, we test the effectiveness of the temporal difference reinforcement learning algorithm (TD(0)). For periodic pulsatile stimulation, we derive a relation that describes, for any stimulation frequency, the minimal pulse amplitude required to suppress seizures. The TD(0) algorithm is able to identify parameters that control seizures quickly. Additionally, our results show that the TD(0) algorithm refines the stimulation frequency to minimize stimulation energy thereby converging to optimal parameters reliably. An advantage of the TD(0) algorithm is that it is adaptive so that the parameters necessary to control the seizures can change over time. We show that the algorithm can converge on the optimal solution in simulation with slow and fast inter-seizure intervals.

Intergroup Biases in Fear-induced Aggression

PubMed Central

Mifune, Nobuhiro; Simunovic, Dora; Yamagishi, Toshio

2017-01-01

Using a recently created preemptive strike game (PSG) with 176 participants, we investigated if the motivations of spite and/or fear promotes aggression that requires a small cost to the aggressor and imposes a larger cost on the opponent, and confirmed the earlier finding that fear does but spite does not promote intergroup aggression when the groups are characterized as minimal groups; additionally, the rate of intergroup aggression did not vary according to the group membership of the opponent. The PSG represents a situation in which both the motivations of spite and of fear can logically drive players to choose an option of aggression against an opponent. Participants decide whether or not to attack another participant, who also has the same capability. The decision is made in real time, using a computer. We discuss theoretical implications of our findings on the evolutionary foundations of intragroup cooperation and intergroup aggression. The evolutionary model of intergroup aggression, or the parochial altruism model, posits that intragroup cooperation and intergroup aggression have co-evolved, and thus it predicts both intragroup cooperation and intergroup aggression to emerge even in a minimal group devoid of a history of intergroup relationships. The finding that only intragroup cooperation but not intergroup aggression emerged in the minimal group experiments strongly suggests that intergroup aggression involves a psychological mechanism that is independent from that of intragroup cooperation. We further discuss the implications of these findings on real-world politics and military strategy. PMID:28174553

Minimally flavored colored scalar in and the mass matrices constraints

NASA Astrophysics Data System (ADS)

Doršner, Ilja; Fajfer, Svjetlana; Košnik, Nejc; Nišandžić, Ivan

2013-11-01

The presence of a colored scalar that is a weak doublet with fractional electric charges of | Q| = 2 /3 and | Q| = 5 /3 with mass below 1 TeV can provide an explanation of the observed branching ratios in decays. The required combination of scalar and tensor operators in the effective Hamiltonian for is generated through the t-channel exchange. We focus on a scenario with a minimal set of Yukawa couplings that can address a semitauonic puzzle and show that its resolution puts a nontrivial bound on the product of the scalar couplings to and . We also derive additional constraints posed by , muon magnetic moment, lepton flavor violating decays μ → eγ, τ → μγ, τ → eγ, and τ electric dipole moment. The minimal set of Yukawa couplings is not only compatible with the mass generation in an SU(5) unification framework, a natural environment for colored scalars, but specifies all matter mixing parameters except for one angle in the up-type quark sector. We accordingly spell out predictions for the proton decay signatures through gauge boson exchange and show that p → π0 e + is suppressed with respect to and even p → K 0 e + in some parts of available parameter space. Impact of the colored scalar embedding in 45-dimensional representation of SU(5) on low-energy phenomenology is also presented. Finally, we make predictions for rare top and charm decays where presence of this scalar can be tested independently.

Minimally invasive plate augmentation in the treatment of long-bone non-unions.

PubMed

Park, Ki-Chul; Oh, Chang-Wug; Kim, Joon-Woo; Park, Kyeong-Hyeon; Oh, Jong-Keon; Park, Il-Hyung; Kyung, Hee-Soo; Heo, Jeong

2017-11-01

Exchange nailing is most acceptable for treating hypertrophic non-union of the long bones, requiring the removal of previously fixed implant. However, its main effect of mechanical stabilization is controversial in non-isthmal area. We hypothesized that minimally invasive plate augmentation over the non-union site may have a better option, without the need of bone grafting or removing pre-existing implants. Seventeen patients with hypertrophic non-union of the long bones between 2010 and 2014 on radiography who previously underwent intramedullary (IM) nailing or plate osteosynthesis for long-bone fractures were included. A locking compression plate was inserted with at least three mono- or bicortical screws at each proximal and distal segment. Broken or loosened interlocking screws of IM nail were simultaneously re-fixed. Fracture site exposure, pre-fixed implant removal, and bone grafting were not performed. We investigated whether union occurred and analyzed functional outcomes and complications. Eleven femoral and six tibial non-unions were prospectively included. In the pre-existing implants, 13 nails and 4 plates were found. All cases achieved union at a mean 22.7 weeks. One case of superficial infection was managed with oral antibiotics. Deep infection or implant failure did not occur. Minimally invasive plate augmentation can achieve additional stability and promote healing of hypertrophic non-union of the long bones. When indicated, this technique is the least invasive alternative to exchange nailing and reduces surgical risks in the treatment of diaphyseal non-union.

Scandinavian Total Ankle Replacement: 15-Year Follow-up.

PubMed

Palanca, Ariel; Mann, Roger A; Mann, Jeffrey A; Haskell, Andrew

2018-02-01

Over the past decade, total ankle arthroplasty (TAA) has become a mainstay in the treatment of end-stage ankle arthritis. Currently in its fourth generation, the Scandanavian Total Ankle Replacement (STAR) is the only 3-piece mobile bearing ankle prosthesis available in the United States. Our current study reports implant survivorship at 15 years and patient outcomes for a subset of these survivors available for study. Eighty-four TAAs were performed between 1998 and 2000. Metal component survivorship at 15 years was calculated with a Kaplan-Meier curve. Twenty-four (29%) of 84 patients were available for participation with a minimum 15-year follow-up. Any radiographic changes were documented. All additional procedures and complications were recorded. Clinical findings, self-reported performance and pain evaluations, and AOFAS ankle/hindfoot scores were noted. Metal implant survival was 73% at 15 years. Of the 24 patients available for clinical evaluation, 18 of 24 patients (70.7%) had no change in prosthetic alignment from the immediate postoperative radiograph. Only 1 subtalar fusion was required for symptomatic adjacent joint arthritis. Three patients sustained a broken polyethylene component. AOFAS scores improved from an average of 39.6 points preoperatively, to an average of 71.6. More than half (52.4%) of patients with retained implants required an additional surgical procedure; 3 required 2 additional procedures. The average time to subsequent procedure was 10.2 years. Our small cohort demonstrated STAR ankles with retention at 9 years were highly likely to survive to 15 years, and patients continued to have significant improvement in pain relief and minimal decrease in function. At 15 years from TAA, metal survivorship was 73%. As with all ankle replacements, supplementary procedures were common. Level IV, case series.