Dry-grind processing using amylase corn and superior yeast to reduce the exogenous enzyme requirements in bioethanol production.

PubMed

Kumar, Deepak; Singh, Vijay

2016-01-01

Conventional corn dry-grind ethanol production process requires exogenous alpha and glucoamylases enzymes to breakdown starch into glucose, which is fermented to ethanol by yeast. This study evaluates the potential use of new genetically engineered corn and yeast, which can eliminate or minimize the use of these external enzymes, improve the economics and process efficiencies, and simplify the process. An approach of in situ ethanol removal during fermentation was also investigated for its potential to improve the efficiency of high-solid fermentation, which can significantly reduce the downstream ethanol and co-product recovery cost. The fermentation of amylase corn (producing endogenous α-amylase) using conventional yeast and no addition of exogenous α-amylase resulted in ethanol concentration of 4.1 % higher compared to control treatment (conventional corn using exogenous α-amylase). Conventional corn processed with exogenous α-amylase and superior yeast (producing glucoamylase or GA) with no exogenous glucoamylase addition resulted in ethanol concentration similar to control treatment (conventional yeast with exogenous glucoamylase addition). Combination of amylase corn and superior yeast required only 25 % of recommended glucoamylase dose to complete fermentation and achieve ethanol concentration and yield similar to control treatment (conventional corn with exogenous α-amylase, conventional yeast with exogenous glucoamylase). Use of superior yeast with 50 % GA addition resulted in similar increases in yield for conventional or amylase corn of approximately 7 % compared to that of control treatment. Combination of amylase corn, superior yeast, and in situ ethanol removal resulted in a process that allowed complete fermentation of 40 % slurry solids with only 50 % of exogenous GA enzyme requirements and 64.6 % higher ethanol yield compared to that of conventional process. Use of amylase corn and superior yeast in the dry-grind processing industry can reduce the total external enzyme usage by more than 80 %, and combining their use with in situ removal of ethanol during fermentation allows efficient high-solid fermentation.

14 CFR 60.16 - Additional qualifications for a currently qualified FSTD.

Code of Federal Regulations, 2010 CFR

2010-01-01

... TRANSPORTATION (CONTINUED) AIRMEN FLIGHT SIMULATION TRAINING DEVICE INITIAL AND CONTINUING QUALIFICATION AND USE... required to undergo an additional qualification process if a user intends to use the FSTD for meeting... that FSTD. This process consists of the following: (1) The sponsor: (i) Must submit to the NSPM all...

From sequencer to supercomputer: an automatic pipeline for managing and processing next generation sequencing data.

PubMed

Camerlengo, Terry; Ozer, Hatice Gulcin; Onti-Srinivasan, Raghuram; Yan, Pearlly; Huang, Tim; Parvin, Jeffrey; Huang, Kun

2012-01-01

Next Generation Sequencing is highly resource intensive. NGS Tasks related to data processing, management and analysis require high-end computing servers or even clusters. Additionally, processing NGS experiments requires suitable storage space and significant manual interaction. At The Ohio State University's Biomedical Informatics Shared Resource, we designed and implemented a scalable architecture to address the challenges associated with the resource intensive nature of NGS secondary analysis built around Illumina Genome Analyzer II sequencers and Illumina's Gerald data processing pipeline. The software infrastructure includes a distributed computing platform consisting of a LIMS called QUEST (http://bisr.osumc.edu), an Automation Server, a computer cluster for processing NGS pipelines, and a network attached storage device expandable up to 40TB. The system has been architected to scale to multiple sequencers without requiring additional computing or labor resources. This platform provides demonstrates how to manage and automate NGS experiments in an institutional or core facility setting.

Validation of the FEA of a deep drawing process with additional force transmission

NASA Astrophysics Data System (ADS)

Behrens, B.-A.; Bouguecha, A.; Bonk, C.; Grbic, N.; Vucetic, M.

2017-10-01

In order to meet requirements by automotive industry like decreasing the CO2 emissions, which reflects in reducing vehicles mass in the car body, the chassis and the powertrain, the continuous innovation and further development of existing production processes are required. In sheet metal forming processes the process limits and components characteristics are defined through the process specific loads. While exceeding the load limits, a failure in the material occurs, which can be avoided by additional force transmission activated in the deep drawing process before the process limit is achieved. This contribution deals with experimental investigations of a forming process with additional force transmission regarding the extension of the process limits. Based on FEA a tool system is designed and developed by IFUM. For this purpose, the steel material HCT600 is analyzed numerically. Within the experimental investigations, the deep drawing processes, with and without the additional force transmission are carried out. Here, a comparison of the produced rectangle cups is done. Subsequently, the identical deep drawing processes are investigated numerically. Thereby, the values of the punch reaction force and displacement are estimated and compared with experimental results. Thus, the validation of material model is successfully carried out on process scale. For further quantitative verification of the FEA results the experimental determined geometry of the rectangular cup is measured optically with ATOS system of the company GOM mbH and digitally compared with external software Geomagic®QualifyTM. The goal of this paper is the verification of the transferability of the FEA model for a conventional deep drawing process to a deep drawing process with additional force transmission with a counter punch.

Data reduction complex analog-to-digital data processing requirements for onsite test facilities

NASA Technical Reports Server (NTRS)

Debbrecht, J. D.

1976-01-01

The analog to digital processing requirements of onsite test facilities are described. The source and medium of all input data to the Data Reduction Complex (DRC) and the destination and medium of all output products of the analog-to-digital processing are identified. Additionally, preliminary input and output data formats are presented along with the planned use of the output products.

30 CFR 933.773 - Requirements for permits and permit processing.

Code of Federal Regulations, 2012 CFR

2012-07-01

... in a soil conservation district (NCGS 139-9); and compliance with any county ordinance regarding...; (ii) Request additional information required for completeness stating specifically what information...

30 CFR 933.773 - Requirements for permits and permit processing.

Code of Federal Regulations, 2014 CFR

2014-07-01

... in a soil conservation district (NCGS 139-9); and compliance with any county ordinance regarding...; (ii) Request additional information required for completeness stating specifically what information...

30 CFR 933.773 - Requirements for permits and permit processing.

Code of Federal Regulations, 2011 CFR

2011-07-01

... in a soil conservation district (NCGS 139-9); and compliance with any county ordinance regarding...; (ii) Request additional information required for completeness stating specifically what information...

30 CFR 933.773 - Requirements for permits and permit processing.

Code of Federal Regulations, 2013 CFR

2013-07-01

... in a soil conservation district (NCGS 139-9); and compliance with any county ordinance regarding...; (ii) Request additional information required for completeness stating specifically what information...

Hot working behavior of selective laser melted and laser metal deposited Inconel 718

NASA Astrophysics Data System (ADS)

Bambach, Markus; Sizova, Irina

2018-05-01

The production of Nickel-based high-temperature components is of great importance for the transport and energy sector. Forging of high-temperature alloys often requires expensive dies, multiple forming steps and leads to forged parts with tolerances that require machining to create the final shape and a large amount of scrap. Additive manufacturing offers the possibility to print the desired shapes directly as net-shape components, requiring only little additional effort in machining. Especially for high-temperature alloys carrying a large amount of energy per unit mass, additive manufacturing could be more energy-efficient than forging if the energy contained in the machining scrap exceeds the energy needed for powder production and laser processing. However, the microstructure and performance of 3d-printed parts will not reach the level of forged material unless further expensive processes such as hot-isostatic pressing are used. Using the design freedom and possibilities to locally engineer material, additive manufacturing could be combined with forging operations to novel process chains, offering the possibility to reduce the number of forging steps and to create near-net shape forgings with desired local properties. Some innovative process chains combining additive manufacturing and forging have been patented recently, but almost no scientific knowledge on the workability of 3D printed preforms exists. The present study investigates the flow stress and microstructure evolution during hot working of pre-forms produced by laser powder deposition and selective laser melting (Figure 1) and puts forward a model for the flow stress.

A study of the additional costs of dispensing workers' compensation prescriptions.

PubMed

Schafermeyer, Kenneth W

2007-03-01

Although there is a significant amount of additional work involved in dispensing workers' compensation prescriptions, these costs have not been quantified. A study of the additional costs to dispense a workers' compensation prescription is needed to measure actual costs and to help determine the reasonableness of reimbursement for prescriptions dispensed under workers' compensation programs. The purpose of this study was to determine the minimum additional time and costs required to dispense workers' compensation prescriptions in Texas. A convenience sample of 30 store-level pharmacy staff members involved in submitting and processing prescription claims for the Texas Mutual workers' compensation program were interviewed by telephone. Data collected to determine the additional costs of dispensing a workers' compensation prescription included (1) the amount of additional time and personnel costs required to dispense and process an average workers' compensation prescription claim, (2) the difference in time required for a new versus a refilled prescription, (3) overhead costs for processing workers' compensation prescription claims by experienced experts at a central processing facility, (4) carrying costs for workers' compensation accounts receivable, and (5) bad debts due to uncollectible workers' compensation claims. The median of the sample pharmacies' additional costs for dispensing a workers' compensation prescription was estimated to be at least $9.86 greater than for a cash prescription. This study shows that the estimated costs for workers' compensation prescriptions were significantly higher than for cash prescriptions. These costs are probably much more than most employers, workers' compensation payers, and pharmacy managers would expect. It is recommended that pharmacy managers should estimate their own costs and compare these costs to actual reimbursement when considering the reasonableness of workers' compensation prescriptions and whether to accept these prescriptions.

Automatic and Controlled Processing in Sentence Recall: The Role of Long-Term and Working Memory

ERIC Educational Resources Information Center

Jefferies, E.; Lambon Ralph, M.A.; Baddeley, A.D.

2004-01-01

Immediate serial recall is better for sentences than word lists presumably because of the additional support that meaningful material receives from long-term memory. This may occur automatically, without the involvement of attention, or may require additional attentionally demanding processing. For example, the episodic buffer model (Baddeley,…

Data management and processing plan, Department of Applied Geodesy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1992-08-01

This plan outlines Data Management and Data Processing requirements of the Department of Applied Geodesy (DAG) and presents the plan to meet these requirements (These requirements are derived from the functional needs of the Department to meet the SSCL alignment tolerances and schedules). In addition, this document presents a schedule for the implementation of this plan. This document is an integral part of the Alignment Plan of the SSCL.

Usage of information safety requirements in improving tube bending process

NASA Astrophysics Data System (ADS)

Livshitz, I. I.; Kunakov, E.; Lontsikh, P. A.

2018-05-01

This article is devoted to an improvement of the technological process's analysis with the information security requirements implementation. The aim of this research is the competition increase analysis in aircraft industry enterprises due to the information technology implementation by the example of the tube bending technological process. The article analyzes tube bending kinds and current technique. In addition, a potential risks analysis in a tube bending technological process is carried out in terms of information security.

21 CFR 640.11 - General requirements.

Code of Federal Regulations, 2010 CFR

2010-04-01

... ADDITIONAL STANDARDS FOR HUMAN BLOOD AND BLOOD PRODUCTS Red Blood Cells § 640.11 General requirements. (a) Storage. Immediately after processing, the Red Blood Cells shall be placed in storage and maintained at a...

OPERATOR BURDEN IN METAL ADDITIVE MANUFACTURING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Elliott, Amy M; Love, Lonnie J

2016-01-01

Additive manufacturing (AM) is an emerging manufacturing process that creates usable machine parts via layer-by-layer joining of a stock material. With this layer-wise approach, high-performance geometries can be created which are impossible with traditional manufacturing methods. Metal AM technology has the potential to significantly reduce the manufacturing burden of developing custom hardware; however, a major consideration in choosing a metal AM system is the required amount of operator involvement (i.e., operator burden) in the manufacturing process. The operator burden not only determines the amount of operator training and specialization required but also the usability of the system in a facility.more » As operators of several metal AM processes, the Manufacturing Demonstration Facility (MDF) at Oak Ridge National Labs is uniquely poised to provide insight into requirements for operator involvement in each of the three major metal AM processes. The paper covers an overview of each of the three metal AM technologies, focusing on the burden on the operator to complete the build cycle, process the part for final use, and reset the AM equipment for future builds.« less

Healthcare software assurance.

PubMed

Cooper, Jason G; Pauley, Keith A

2006-01-01

Software assurance is a rigorous, lifecycle phase-independent set of activities which ensure completeness, safety, and reliability of software processes and products. This is accomplished by guaranteeing conformance to all requirements, standards, procedures, and regulations. These assurance processes are even more important when coupled with healthcare software systems, embedded software in medical instrumentation, and other healthcare-oriented life-critical systems. The current Food and Drug Administration (FDA) regulatory requirements and guidance documentation do not address certain aspects of complete software assurance activities. In addition, the FDA's software oversight processes require enhancement to include increasingly complex healthcare systems such as Hospital Information Systems (HIS). The importance of complete software assurance is introduced, current regulatory requirements and guidance discussed, and the necessity for enhancements to the current processes shall be highlighted.

Healthcare Software Assurance

PubMed Central

Cooper, Jason G.; Pauley, Keith A.

2006-01-01

Software assurance is a rigorous, lifecycle phase-independent set of activities which ensure completeness, safety, and reliability of software processes and products. This is accomplished by guaranteeing conformance to all requirements, standards, procedures, and regulations. These assurance processes are even more important when coupled with healthcare software systems, embedded software in medical instrumentation, and other healthcare-oriented life-critical systems. The current Food and Drug Administration (FDA) regulatory requirements and guidance documentation do not address certain aspects of complete software assurance activities. In addition, the FDA’s software oversight processes require enhancement to include increasingly complex healthcare systems such as Hospital Information Systems (HIS). The importance of complete software assurance is introduced, current regulatory requirements and guidance discussed, and the necessity for enhancements to the current processes shall be highlighted. PMID:17238324

Towards a Cloud Computing Environment: Near Real-time Cloud Product Processing and Distribution for Next Generation Satellites

NASA Astrophysics Data System (ADS)

Nguyen, L.; Chee, T.; Minnis, P.; Palikonda, R.; Smith, W. L., Jr.; Spangenberg, D.

2016-12-01

The NASA LaRC Satellite ClOud and Radiative Property retrieval System (SatCORPS) processes and derives near real-time (NRT) global cloud products from operational geostationary satellite imager datasets. These products are being used in NRT to improve forecast model, aircraft icing warnings, and support aircraft field campaigns. Next generation satellites, such as the Japanese Himawari-8 and the upcoming NOAA GOES-R, present challenges for NRT data processing and product dissemination due to the increase in temporal and spatial resolution. The volume of data is expected to increase to approximately 10 folds. This increase in data volume will require additional IT resources to keep up with the processing demands to satisfy NRT requirements. In addition, these resources are not readily available due to cost and other technical limitations. To anticipate and meet these computing resource requirements, we have employed a hybrid cloud computing environment to augment the generation of SatCORPS products. This paper will describe the workflow to ingest, process, and distribute SatCORPS products and the technologies used. Lessons learn from working on both AWS Clouds and GovCloud will be discussed: benefits, similarities, and differences that could impact decision to use cloud computing and storage. A detail cost analysis will be presented. In addition, future cloud utilization, parallelization, and architecture layout will be discussed for GOES-R.

Overlay metrology for double patterning processes

NASA Astrophysics Data System (ADS)

Leray, Philippe; Cheng, Shaunee; Laidler, David; Kandel, Daniel; Adel, Mike; Dinu, Berta; Polli, Marco; Vasconi, Mauro; Salski, Bartlomiej

2009-03-01

The double patterning (DPT) process is foreseen by the industry to be the main solution for the 32 nm technology node and even beyond. Meanwhile process compatibility has to be maintained and the performance of overlay metrology has to improve. To achieve this for Image Based Overlay (IBO), usually the optics of overlay tools are improved. It was also demonstrated that these requirements are achievable with a Diffraction Based Overlay (DBO) technique named SCOLTM [1]. In addition, we believe that overlay measurements with respect to a reference grid are required to achieve the required overlay control [2]. This induces at least a three-fold increase in the number of measurements (2 for double patterned layers to the reference grid and 1 between the double patterned layers). The requirements of process compatibility, enhanced performance and large number of measurements make the choice of overlay metrology for DPT very challenging. In this work we use different flavors of the standard overlay metrology technique (IBO) as well as the new technique (SCOL) to address these three requirements. The compatibility of the corresponding overlay targets with double patterning processes (Litho-Etch-Litho-Etch (LELE); Litho-Freeze-Litho-Etch (LFLE), Spacer defined) is tested. The process impact on different target types is discussed (CD bias LELE, Contrast for LFLE). We compare the standard imaging overlay metrology with non-standard imaging techniques dedicated to double patterning processes (multilayer imaging targets allowing one overlay target instead of three, very small imaging targets). In addition to standard designs already discussed [1], we investigate SCOL target designs specific to double patterning processes. The feedback to the scanner is determined using the different techniques. The final overlay results obtained are compared accordingly. We conclude with the pros and cons of each technique and suggest the optimal metrology strategy for overlay control in double patterning processes.

The study on knowledge transferring incentive for information system requirement development

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Yang

2015-03-10

Information system requirement development is a process of users’ knowledge sharing and transferring. However the tacit requirements developing is a main problem during requirement development process, for the reason of difficult to encoding, express, and communicate. Knowledge fusion and corporate effort is needed to finding tacit requirements. Under this background, our paper try to find out the rule of effort dynamic evolutionary of software developer and user by building an evolutionary game model on the condition of incentive system. And in addition this paper provides an in depth discussion at the end of this paper.

A Student's Guide to Navigating the IRB: How to Successfully Navigate a Potentially Overwhelming Process

ERIC Educational Resources Information Center

Murphy, Corinne M.; Verden, Claire

2011-01-01

Graduate students must complete a research project to receive their degree. In addition to this basic requirement, the student may be required to submit a research proposal and application to the governing Institutional Review Board (IRB) for approval prior to beginning the research project. This article describes the IRB process and offers tips…

Selective laser melting of Inconel super alloy-a review

NASA Astrophysics Data System (ADS)

Karia, M. C.; Popat, M. A.; Sangani, K. B.

2017-07-01

Additive manufacturing is a relatively young technology that uses the principle of layer by layer addition of material in solid, liquid or powder form to develop a component or product. The quality of additive manufactured part is one of the challenges to be addressed. Researchers are continuously working at various levels of additive manufacturing technologies. One of the significant powder bed processes for met als is Selective Laser Melting (SLM). Laser based processes are finding more attention of researchers and industrial world. The potential of this technique is yet to be fully explored. Due to very high strength and creep resistance Inconel is extensively used nickel based super alloy for manufacturing components for aerospace, automobile and nuclear industries. Due to law content of Aluminum and Titanium, it exhibits good fabricability too. Therefore the alloy is ideally suitable for selective laser melting to manufacture intricate components with high strength requirements. The selection of suitable process for manufacturing for a specific component depends on geometrical complexity, production quantity, and cost and required strength. There are numerous researchers working on various aspects like metallurgical and micro structural investigations and mechanical properties, geometrical accuracy, effects of process parameters and its optimization and mathematical modeling etc. The present paper represents a comprehensive overview of selective laser melting process for Inconel group of alloys.

Aircraft Alerting Systems Standardization Study. Phase IV. Accident Implications on Systems Design.

DTIC Science & Technology

1982-06-01

computing and processing to assimilate and process status informa- 5 tion using...provided with capabilities in computing and processing , sensing, interfacing, and controlling and displaying. 17 o Computing and Processing - Algorithms...alerting system to perform a flight status monitor function would require additional sensinq, computing and processing , interfacing, and controlling

Technical Assistance Needs Assessments (TANAs)

EPA Pesticide Factsheets

The Technical Assistance Needs Assessment (TANA) is a process to identify whether a community requires additional support from EPA in order to understand technical information and have meaningful participation in the Superfund decision-making process.

Development of Airport Surface Required Navigation Performance (RNP)

NASA Technical Reports Server (NTRS)

Cassell, Rick; Smith, Alex; Hicok, Dan

1999-01-01

The U.S. and international aviation communities have adopted the Required Navigation Performance (RNP) process for defining aircraft performance when operating the en-route, approach and landing phases of flight. RNP consists primarily of the following key parameters - accuracy, integrity, continuity, and availability. The processes and analytical techniques employed to define en-route, approach and landing RNP have been applied in the development of RNP for the airport surface. To validate the proposed RNP requirements several methods were used. Operational and flight demonstration data were analyzed for conformance with proposed requirements, as were several aircraft flight simulation studies. The pilot failure risk component was analyzed through several hypothetical scenarios. Additional simulator studies are recommended to better quantify crew reactions to failures as well as additional simulator and field testing to validate achieved accuracy performance, This research was performed in support of the NASA Low Visibility Landing and Surface Operations Programs.

Alloy-steel nuts for bolting for high-pressure and high-temperature service (ASME SA-194 with additional requirements)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This standard covers alloy steel nuts for bolting for high-pressure and high-temperature service in nuclear and associated applications. This standard does not cover bar or other starting materials. The only implied special considerations for starting materials are that they be capable of passing the required tests when processed into finished products in accordance with this standard. Material shall conform to the requirements of ASME SA-194; to the requirements of the ASME Boiler and Pressure Vessel Code (ASME Code), Section III, Article NB-2000; to the requirements of NE E 8-18; and to the additional requirements of this standard.

33 CFR 148.107 - What additional information may be required?

Code of Federal Regulations, 2010 CFR

2010-07-01

... HOMELAND SECURITY (CONTINUED) DEEPWATER PORTS DEEPWATER PORTS: GENERAL Application for a License § 148.107...), in coordination with MARAD, may determine whether compliance with the requirement is important to processing the application within the time prescribed by the Act. (3) If the requirement is important to...

GUIDANCE DOCUMENT ON IMPLEMENTATION OF THE ...

EPA Pesticide Factsheets

The Agreement in Principle for the Stage 2 M-DBP Federal Advisory Committee contains a list of treatment processes and management practices for water systems to use in meeting additional Cryptosporidium treatment requirements under the LT2ESWTR. This list, termed the microbial toolbox, includes watershed control programs, alternative intake locations, pretreatment processes, additional filtration barriers, inactivation technologies, and enhanced plant performance. The intent of the microbial toolbox is to provide water systems with broad flexibility in selecting cost-effective LT2ESWTR compliance strategies. Moreover, the toolbox allows systems that currently provide additional pathogen barriers or that can demonstrate enhanced performance to receive additional Cryptosporidium treatment credit. Provide guidance to utilities with surface water supplies and to state drinking water programs on the use of different treatment technologies to reduce the level of Cryptosporidium in drinking water. Technologies included in the guidance manual may be used to achieve compliance with the requirements of the LT2ESWTR.

Plants with genetically modified events combined by conventional breeding: an assessment of the need for additional regulatory data.

PubMed

Pilacinski, W; Crawford, A; Downey, R; Harvey, B; Huber, S; Hunst, P; Lahman, L K; MacIntosh, S; Pohl, M; Rickard, C; Tagliani, L; Weber, N

2011-01-01

Crop varieties with multiple GM events combined by conventional breeding have become important in global agriculture. The regulatory requirements in different countries for such products vary considerably, placing an additional burden on regulatory agencies in countries where the submission of additional data is required and delaying the introduction of innovative products to meet agricultural needs. The process of conventional plant breeding has predictably provided safe food and feed products both historically and in the modern era of plant breeding. Thus, previously approved GM events that have been combined by conventional plant breeding and contain GM traits that are not likely to interact in a manner affecting safety should be considered to be as safe as their conventional counterparts. Such combined GM event crop varieties should require little, if any, additional regulatory data to meet regulatory requirements. Copyright © 2010 Elsevier Ltd. All rights reserved.

Additive Manufacturing: Ensuring Quality for Spacecraft Applications

NASA Technical Reports Server (NTRS)

Swanson, Theodore; Stephenson, Timothy

2014-01-01

Reliable manufacturing requires that material properties and fabrication processes be well defined in order to insure that the manufactured parts meet specified requirements. While this issue is now relatively straightforward for traditional processes such as subtractive manufacturing and injection molding, this capability is still evolving for AM products. Hence, one of the principal challenges within AM is in qualifying and verifying source material properties and process control. This issue is particularly critical for applications in harsh environments and demanding applications, such as spacecraft.

Economic comparison of conventional maintenance and electrochemical oxidation to warrant water safety in dental unit water lines.

PubMed

Fischer, Sebastian; Meyer, Georg; Kramer, Axel

2012-01-01

In preparation for implementation of a central water processing system at a dental department, we analyzed the costs of conventional decentralized disinfection of dental units against a central water treatment concept based on electrochemical disinfection. The cost evaluation included only the costs of annually required antimicrobial consumables and additional water usage of a decentralize conventional maintenance system for dental water lines build in the respective dental units and the central electrochemical water disinfection system, BLUE SAFETY™ Technologies. In total, analysis of costs of 6 dental departments reviled additional annual costs for hygienic preventive measures of € 4,448.37. For the BLUE SAFETY™ Technology, the additional annual total agent consumption costs were € 2.18, accounting for approximately 0.05% of the annual total agent consumption costs of the conventional maintenance system. For both water processing concepts, the additional costs for energy could not be calculated, since the required data was not obtainable from the manufacturers. For both concepts, the investment and maintenance costs were not calculated due to lack of manufacturer's data. Therefore, the results indicate the difference of costs for the required consumables only. Aside of the significantly lower annual costs for required consumables and disinfectants; a second advantage for the BLUE SAFETY™ Technology is its constant and automatic operation, which does not require additional staff resources. This not only safety human resources, but add additionally to cost saving. Since the antimicrobial disinfection capacity of the BLUE SAFETY™ was demonstrated previously and is well known, this technology, which is comparable or even superior in its non-corrosive effect, may be regarded as method of choice for continuous disinfection and prevention of biofilm formation in dental units' water lines.

Economic comparison of conventional maintenance and electrochemical oxidation to warrant water safety in dental unit water lines

PubMed Central

Fischer, Sebastian; Meyer, Georg; Kramer, Axel

2012-01-01

Background: In preparation for implementation of a central water processing system at a dental department, we analyzed the costs of conventional decentralized disinfection of dental units against a central water treatment concept based on electrochemical disinfection. Methods: The cost evaluation included only the costs of annually required antimicrobial consumables and additional water usage of a decentralize conventional maintenance system for dental water lines build in the respective dental units and the central electrochemical water disinfection system, BLUE SAFETY™ Technologies. Results: In total, analysis of costs of 6 dental departments reviled additional annual costs for hygienic preventive measures of € 4,448.37. For the BLUE SAFETY™ Technology, the additional annual total agent consumption costs were € 2.18, accounting for approximately 0.05% of the annual total agent consumption costs of the conventional maintenance system. For both water processing concepts, the additional costs for energy could not be calculated, since the required data was not obtainable from the manufacturers. Discussion: For both concepts, the investment and maintenance costs were not calculated due to lack of manufacturer's data. Therefore, the results indicate the difference of costs for the required consumables only. Aside of the significantly lower annual costs for required consumables and disinfectants; a second advantage for the BLUE SAFETY™ Technology is its constant and automatic operation, which does not require additional staff resources. This not only safety human resources, but add additionally to cost saving. Conclusion: Since the antimicrobial disinfection capacity of the BLUE SAFETY™ was demonstrated previously and is well known, this technology, which is comparable or even superior in its non-corrosive effect, may be regarded as method of choice for continuous disinfection and prevention of biofilm formation in dental units’ water lines. PMID:22558042

Additive Manufacturing of Tooling for Refrigeration Cabinet Foaming Processes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Post, Brian K; Nuttall, David; Cukier, Michael

The primary objective of this project was to leverage the Big Area Additive Manufacturing (BAAM) process and materials into a long term, quick change tooling concept to drastically reduce product lead and development timelines and costs. Current refrigeration foam molds are complicated to manufacture involving casting several aluminum parts in an approximate shape, machining components of the molds and post fitting and shimming of the parts in an articulated fixture. The total process timeline can take over 6 months. The foaming process is slower than required for production, therefore multiple fixtures, 10 to 27, are required per refrigerator model. Moldsmore » are particular to a specific product configuration making mixed model assembly challenging for sequencing, mold changes or auto changeover features. The initial goal was to create a tool leveraging the ORNL materials and additive process to build a tool in 4 to 6 weeks or less. A secondary goal was to create common fixture cores and provide lightweight fixture sections that could be revised in a very short time to increase equipment flexibility reduce lead times, lower the barriers to first production trials, and reduce tooling costs.« less

42 CFR 493.557 - Additional submission requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... CMS determines are necessary for validation and assessment of the State's inspection process... the information specified in §§ 493.553 and 493.555, as part of the approval and review process, an... process, including, but not limited to the following: (i) The size and composition of individual...

42 CFR 493.557 - Additional submission requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... CMS determines are necessary for validation and assessment of the State's inspection process... the information specified in §§ 493.553 and 493.555, as part of the approval and review process, an... process, including, but not limited to the following: (i) The size and composition of individual...

42 CFR 493.557 - Additional submission requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... CMS determines are necessary for validation and assessment of the State's inspection process... the information specified in §§ 493.553 and 493.555, as part of the approval and review process, an... process, including, but not limited to the following: (i) The size and composition of individual...

42 CFR 493.557 - Additional submission requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... CMS determines are necessary for validation and assessment of the State's inspection process... the information specified in §§ 493.553 and 493.555, as part of the approval and review process, an... process, including, but not limited to the following: (i) The size and composition of individual...

41 CFR 102-38.225 - What are the additional requirements in the bid process?

Code of Federal Regulations, 2010 CFR

2010-07-01

... bid process? All sales except fixed price sales must contain a certification of independent price... matter to the Department of Justice or your agency's Office of the Inspector General. Bid Deposits ...

Developing Materials Processing to Performance Modeling Capabilities and the Need for Exascale Computing Architectures (and Beyond)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schraad, Mark William; Luscher, Darby Jon

Additive Manufacturing techniques are presenting the Department of Energy and the NNSA Laboratories with new opportunities to consider novel component production and repair processes, and to manufacture materials with tailored response and optimized performance characteristics. Additive Manufacturing technologies already are being applied to primary NNSA mission areas, including Nuclear Weapons. These mission areas are adapting to these new manufacturing methods, because of potential advantages, such as smaller manufacturing footprints, reduced needs for specialized tooling, an ability to embed sensing, novel part repair options, an ability to accommodate complex geometries, and lighter weight materials. To realize the full potential of Additivemore » Manufacturing as a game-changing technology for the NNSA’s national security missions; however, significant progress must be made in several key technical areas. In addition to advances in engineering design, process optimization and automation, and accelerated feedstock design and manufacture, significant progress must be made in modeling and simulation. First and foremost, a more mature understanding of the process-structure-property-performance relationships must be developed. Because Additive Manufacturing processes change the nature of a material’s structure below the engineering scale, new models are required to predict materials response across the spectrum of relevant length scales, from the atomistic to the continuum. New diagnostics will be required to characterize materials response across these scales. And not just models, but advanced algorithms, next-generation codes, and advanced computer architectures will be required to complement the associated modeling activities. Based on preliminary work in each of these areas, a strong argument for the need for Exascale computing architectures can be made, if a legitimate predictive capability is to be developed.« less

DATA QUALITY OBJECTIVES FOR SELECTING WASTE SAMPLES FOR THE BENCH STEAM REFORMER TEST

DOE Office of Scientific and Technical Information (OSTI.GOV)

BANNING DL

2010-08-03

This document describes the data quality objectives to select archived samples located at the 222-S Laboratory for Fluid Bed Steam Reformer testing. The type, quantity and quality of the data required to select the samples for Fluid Bed Steam Reformer testing are discussed. In order to maximize the efficiency and minimize the time to treat Hanford tank waste in the Waste Treatment and Immobilization Plant, additional treatment processes may be required. One of the potential treatment processes is the fluid bed steam reformer (FBSR). A determination of the adequacy of the FBSR process to treat Hanford tank waste is required.more » The initial step in determining the adequacy of the FBSR process is to select archived waste samples from the 222-S Laboratory that will be used to test the FBSR process. Analyses of the selected samples will be required to confirm the samples meet the testing criteria.« less

76 FR 737 - Tobacco Products, Exemptions From Substantial Equivalence Requirements

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-06

... tobacco additive, or increasing or decreasing the quantity of an existing tobacco additive, from the... provision by July 1, 2011. ``Additive'' is defined at section 900(1) of the FD&C Act, as ``any substance the... substances intended for use as a flavoring or coloring or in producing, manufacturing, packing, processing...

The role of attention in item-item binding in visual working memory.

PubMed

Peterson, Dwight J; Naveh-Benjamin, Moshe

2017-09-01

An important yet unresolved question regarding visual working memory (VWM) relates to whether or not binding processes within VWM require additional attentional resources compared with processing solely the individual components comprising these bindings. Previous findings indicate that binding of surface features (e.g., colored shapes) within VWM is not demanding of resources beyond what is required for single features. However, it is possible that other types of binding, such as the binding of complex, distinct items (e.g., faces and scenes), in VWM may require additional resources. In 3 experiments, we examined VWM item-item binding performance under no load, articulatory suppression, and backward counting using a modified change detection task. Binding performance declined to a greater extent than single-item performance under higher compared with lower levels of concurrent load. The findings from each of these experiments indicate that processing item-item bindings within VWM requires a greater amount of attentional resources compared with single items. These findings also highlight an important distinction between the role of attention in item-item binding within VWM and previous studies of long-term memory (LTM) where declines in single-item and binding test performance are similar under divided attention. The current findings provide novel evidence that the specific type of binding is an important determining factor regarding whether or not VWM binding processes require attention. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Pahoa geothermal industrial park. Engineering and economic analysis for direct applications of geothermal energy in an industrial park at Pahoa, Hawaii

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moreau, J.W.

1980-12-01

This engineering and economic study evaluated the potential for developing a geothermal industrial park in the Puna District near Pahoa on the Island of Hawaii. Direct heat industrial applications were analyzed from a marketing, engineering, economic, environmental, and sociological standpoint to determine the most viable industries for the park. An extensive literature search produced 31 existing processes currently using geothermal heat. An additional list was compiled indicating industrial processes that require heat that could be provided by geothermal energy. From this information, 17 possible processes were selected for consideration. Careful scrutiny and analysis of these 17 processes revealed three thatmore » justified detailed economic workups. The three processes chosen for detailed analysis were: an ethanol plant using bagasse and wood as feedstock; a cattle feed mill using sugar cane leaf trash as feedstock; and a papaya processing facility providing both fresh and processed fruit. In addition, a research facility to assess and develop other processes was treated as a concept. Consideration was given to the impediments to development, the engineering process requirements and the governmental support for each process. The study describes the geothermal well site chosen, the pipeline to transmit the hydrothermal fluid, and the infrastructure required for the industrial park. A conceptual development plan for the ethanol plant, the feedmill and the papaya processing facility was prepared. The study concluded that a direct heat industrial park in Pahoa, Hawaii, involves considerable risks.« less

27 CFR 24.300 - General.

Code of Federal Regulations, 2010 CFR

2010-04-01

... record, copy, or reproduce records required by this part and may use any process which accurately... month, bulk wine produced by fermentation, sweetening, blending, amelioration or addition of wine... fermentation, sweetening, blending, amelioration or addition of wine spirits, bulk wine bottled, bulk and...

Low-Cost Rapid Usability Testing: Its Application in Both Product Development and System Implementation.

PubMed

Kushniruk, Andre; Borycki, Elizabeth

2017-01-01

In recent years there has been considerable discussion around the need for certification and regulation of healthcare information technology (IT). In particular, the usability of the products being developed needs to be evaluated. This has included the application of standards designed to ensure the process of system development is user-centered and takes usability into consideration while a product is being developed. In addition to this, in healthcare, organizations in the United States and Europe have also addressed the need and requirement for product certification. However, despite these efforts there are continued reports of unusable and unsafe implementations. In this paper we discuss the need to not only include (and require) usability testing in the one-time development process of health IT products (such as EHRs), but we also argue for the need to additionally develop specific usability standards and requirements for usability testing during the implementation of vendor products (i.e. post product development) in healthcare settings. It is further argued that health IT products that may have been certified regarding their development process will still require application of usability testing in the process of implementing them in real hospital settings in order to ensure usability and safety. This is needed in order to ensure that the final result of both product development and implementation processes take into account and apply the latest usability principles and methods.

Modality dependence and intermodal transfer in the Corsi Spatial Sequence Task: Screen vs. Floor.

PubMed

Röser, Andrea; Hardiess, Gregor; Mallot, Hanspeter A

2016-07-01

Four versions of the Corsi Spatial Sequence Task (CSST) were tested in a complete within-subject design, investigating whether participants' performance depends on the modality of task presentation and reproduction that put different demands on spatial processing. Presentation of the sequence (encoding phase) and the reproduction (recall phase) were each carried out either on a computer screen or on the floor of a room, involving actual walking in the recall phase. Combinations of the two different encoding and recall procedures result in the modality conditions Screen-Screen, Screen-Floor, Floor-Screen, and Floor-Floor. Results show the expected decrease in performance with increasing sequence length, which is likely due to processing limitations of working memory. We also found differences in performance between the modality conditions indicating different involvements of spatial working memory processes. Participants performed best in the Screen-Screen modality condition. Floor-Screen and Floor-Floor modality conditions require additional working memory resources for reference frame transformation and spatial updating, respectively; the resulting impairment of the performance was about the same in these two conditions. Finally, the Screen-Floor modality condition requires both types of additional spatial demands and led to the poorest performance. Therefore, we suggest that besides the well-known spatial requirements of CSST, additional working memory resources are demanded in walking CSST supporting processes such as spatial updating, mental rotation, reference frame transformation, and the control of walking itself.

INTELLIGENT PROCESSING EQUIPMENT WITHIN THE ENVIRONMENTAL PROTECTION AGENCY

EPA Science Inventory

Protection of the environment and environmental remediation requires the cooperation -at all levels- of government and industry. ntelligent processing equipment, in addition to other artificial intelligence based tools, has been used by the Environmental Protection Agency to prov...

On the Processing of Martensitic Steels in Continuous Galvanizing Lines: Part 1

NASA Astrophysics Data System (ADS)

Song, Taejin; Kwak, Jaihyun; de Cooman, B. C.

2012-01-01

Whereas low-carbon (<0.2 mass pct) martensitic grades can be produced easily in continuous annealing processing lines equipped with the required cooling capacity, the thermal cycles in continuous galvanizing lines make it difficult to produce hot-dip Zn or Zn-alloy coated high-strength martensitic grades. This is because of the tempering processes occurring during dipping of the strip in the liquid Zn bath and, in the case of galvannealed sheet steel, the short thermal treatment required to achieve the alloying between the Zn and the steel. These short additional thermal treatments last less than 30 seconds but severely degrade the mechanical properties. Using a combination of internal friction, X-ray diffraction, and transmission electron microscopy, it is shown that the ultrafine-grained lath microstructure allows for a rapid dislocation recovery and carbide formation during the galvanizing processes. In addition, the effective dislocation pinning occurring during the galvannealing process results in strain localization and the suppression of strain hardening.

Scale-up of ethanol production from winter barley by the EDGE (enhanced dry grind enzymatic) process in fermentors up to 300 liters

USDA-ARS?s Scientific Manuscript database

A fermentation process, which was designated the EDGE (enhanced dry grind enzymatic) process, has recently been developed for barley ethanol production. In the EDGE process, in addition to the enzymes normally required for starch hydrolysis, commercial Beta-glucanases were used to hydrolyze (1,3)(1,...

20 CFR 655.154 - Additional positive recruitment.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Section 655.154 Employees' Benefits EMPLOYMENT AND TRAINING ADMINISTRATION, DEPARTMENT OF LABOR TEMPORARY EMPLOYMENT OF FOREIGN WORKERS IN THE UNITED STATES Labor Certification Process for Temporary Agricultural Employment in the United States (H-2A Workers) Post-Acceptance Requirements § 655.154 Additional positive...

Metrology: Calibration and measurement processes guidelines

NASA Technical Reports Server (NTRS)

Castrup, Howard T.; Eicke, Woodward G.; Hayes, Jerry L.; Mark, Alexander; Martin, Robert E.; Taylor, James L.

1994-01-01

The guide is intended as a resource to aid engineers and systems contracts in the design, implementation, and operation of metrology, calibration, and measurement systems, and to assist NASA personnel in the uniform evaluation of such systems supplied or operated by contractors. Methodologies and techniques acceptable in fulfilling metrology quality requirements for NASA programs are outlined. The measurement process is covered from a high level through more detailed discussions of key elements within the process, Emphasis is given to the flowdown of project requirements to measurement system requirements, then through the activities that will provide measurements with defined quality. In addition, innovations and techniques for error analysis, development of statistical measurement process control, optimization of calibration recall systems, and evaluation of measurement uncertainty are presented.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goins, Bobby

A systems based approach will be used to evaluate the nitrogen delivery process. This approach involves principles found in Lean, Reliability, Systems Thinking, and Requirements. This unique combination of principles and thought process yields a very in depth look into the system to which it is applied. By applying a systems based approach to the nitrogen delivery process there should be improvements in cycle time, efficiency, and a reduction in the required number of personnel needed to sustain the delivery process. This will in turn reduce the amount of demurrage charges that the site incurs. In addition there should bemore » less frustration associated with the delivery process.« less

A Systems Approach to Nitrogen Delivery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goins, Bobby

A systems based approach will be used to evaluate the nitrogen delivery process. This approach involves principles found in Lean, Reliability, Systems Thinking, and Requirements. This unique combination of principles and thought process yields a very in depth look into the system to which it is applied. By applying a systems based approach to the nitrogen delivery process there should be improvements in cycle time, efficiency, and a reduction in the required number of personnel needed to sustain the delivery process. This will in turn reduce the amount of demurrage charges that the site incurs. In addition there should bemore » less frustration associated with the delivery process.« less

75 FR 31790 - Determination That Cysteine Hydrochloride Injection, USP, 7.25%, Was Not Withdrawn From Sale for...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-04

... an additive to amino acid solutions to meet the nutritional requirements of newborn infants requiring... have impaired enzymatic processes and require TPN. It can also be added to amino acid solutions to provide a more complete profile of amino acids for protein synthesis. Hospira notified FDA in a letter...

Fort Holabird Defense Investigative Service (DIS), Base Realignment and Closure (BRAC) Cleanup Plan (BCP), Version II

DTIC Science & Technology

1998-12-01

3-16 3.4.7 Category 7: Areas Not Evaluated or Require Additional Evaluation .................... 3-16...Alternatives Evaluation Process for DIS Disposal and Reuse, Fort Holabird, Maryland ........ 2-6 Figure 3-1. Environmental Restoration Early Action...Requirement AREE ............... Area Requiring Environmental Evaluation AST .................. Above-ground Storage Tank BCP .................. BRAC

Safety Assurance in NextGen

NASA Technical Reports Server (NTRS)

HarrisonFleming, Cody; Spencer, Melissa; Leveson, Nancy; Wilkinson, Chris

2012-01-01

The generation of minimum operational, safety, performance, and interoperability requirements is an important aspect of safely integrating new NextGen components into the Communication Navigation Surveillance and Air Traffic Management (CNS/ATM) system. These requirements are used as part of the implementation and approval processes. In addition, they provide guidance to determine the levels of design assurance and performance that are needed for each element of the new NextGen procedures, including aircraft, operator, and Air Navigation and Service Provider. Using the enhanced Airborne Traffic Situational Awareness for InTrail Procedure (ATSA-ITP) as an example, this report describes some limitations of the current process used for generating safety requirements and levels of required design assurance. An alternative process is described, as well as the argument for why the alternative can generate more comprehensive requirements and greater safety assurance than the current approach.

The Road to Realizing In-Space Manufacturing

NASA Technical Reports Server (NTRS)

Clinton, Raymond G.

2014-01-01

Additive Manufacturing in space offers tremendous potential for dramatic paradigm shift in the development and manufacturing of space architectures. Additive Manufacturing in space offers the potential for mission safety risk reduction for low Earth orbit and deep space exploration; new paradigms for maintenance, repair, and logistics. Leverage ground-based technology developments, process characterization, and material properties databases. Investments are required primarily in the microgravity environment. We must do the foundational work. It's not sexy, but it is required.

3D Printing, Additive Manufacturing, and Solid Freeform Fabrication: The Technologies of the Past, Present and Future

NASA Astrophysics Data System (ADS)

Beaman, Joseph

2015-03-01

Starting in the late 1980's, several new technologies were created that have the potential to revolutionize manufacturing. These technologies are, for the most part, additive processes that build up parts layer by layer. In addition, the processes that are being touted for hard-core manufacturing are primarily laser or e-beam based processes. This presentation gives a brief history of Additive Manufacturing and gives an assessment for these technologies. These technologies initially grew out of a commercial need for rapid prototyping. This market has a different requirement for process and quality control than traditional manufacturing. The relatively poor process control of the existing commercial Additive Manufacturing equipment is a vestige of this history. This presentation discusses this history and improvements in quality over time. The emphasis will be on Additive Manufacturing processes that are being considered for direct manufacturing, which is a different market than the 3D Printing ``Makerbot'' market. Topics discussed include past and present machine sensors, materials, and operational methods that were used in the past and those that are used today to create manufactured parts. Finally, a discussion of new methods and future directions of AM is presented.

Development in high-grade dual phase steels with low C and Si design

NASA Astrophysics Data System (ADS)

Zhu, Guo-hui; Zhang, Xue-hui; Mao, Wei-min

2009-12-01

Cold rolled dual phase steels with low C and Si addition were investigated in terms of combination of composition and processing in order to improve mechanical properties and workability including welding and galvanizing. Mo and Cr could be used as alloying elements to partially replace C and Si to assure enough hardening ability of the steels and also give solute-hardening. Mo addition is more effective than Cr addition in terms of obtaining the required volume fraction of martensite and mechanical strength. The ferrite grain was effectively refined by addition of Nb microalloying, which gives optimized mechanical properties. The experimental results show that it is possible to obtain the required mechanical properties of high grade 800 MPa dual phase steel, i.e., tensile strength > 780 MPa, elongation > 15%, and yield/tensile strength ratio < 0.6 in the condition of low carbon (C < 0.11 wt.%) and low silicon design (Si < 0.05 wt.%) through adequate combination of composition and processing.

Biological Hydrogen Production: Simultaneous Saccharification and Fermentation With Nitrogen and Phosphorus Removal from Wastewater Effluent

DTIC Science & Technology

2010-01-01

requiring thermochemical pretreatment , aswould typically be required with lignocellulosic feedstocks. Therefore it offers a readily-processed and...Standards and Technology. The pH of the reactors was controlled throughout all fermentations by the automatic addition of 0.1 N NaOH . Total organic...nutrients. The optimized conditions developed with paper as a substrate may also convey to the use of a similar process with lignocellulosic biomass

NOSS Altimeter Detailed Algorithm specifications

NASA Technical Reports Server (NTRS)

Hancock, D. W.; Mcmillan, J. D.

1982-01-01

The details of the algorithms and data sets required for satellite radar altimeter data processing are documented in a form suitable for (1) development of the benchmark software and (2) coding the operational software. The algorithms reported in detail are those established for altimeter processing. The algorithms which required some additional development before documenting for production were only scoped. The algorithms are divided into two levels of processing. The first level converts the data to engineering units and applies corrections for instrument variations. The second level provides geophysical measurements derived from altimeter parameters for oceanographic users.

Modeling of additive manufacturing processes for metals: Challenges and opportunities

DOE PAGES

Francois, Marianne M.; Sun, Amy; King, Wayne E.; ...

2017-01-09

Here, with the technology being developed to manufacture metallic parts using increasingly advanced additive manufacturing processes, a new era has opened up for designing novel structural materials, from designing shapes and complex geometries to controlling the microstructure (alloy composition and morphology). The material properties used within specific structural components are also designable in order to meet specific performance requirements that are not imaginable with traditional metal forming and machining (subtractive) techniques.

Water-based binary polyol process for the controllable synthesis of silver nanoparticles inhibiting human and foodborne pathogenic bacteria

USDA-ARS?s Scientific Manuscript database

The polyol process is a widely used strategy for producing nanoparticles from various reducible metallic precursors; however it requires a bulk polyol liquid reaction with additional protective agents at high temperatures. Here, we report a water-based binary polyol process using low concentrations ...

Proposed Conceptual Requirements for the CTBT Knowledge Base,

DTIC Science & Technology

1995-08-14

knowledge available to automated processing routines and human analysts are significant, and solving these problems is an essential step in ensuring...knowledge storage in a CTBT system. In addition to providing regional knowledge to automated processing routines, the knowledge base will also address

40 CFR 240.200-2 - Recommended procedures: Design.

Code of Federal Regulations, 2013 CFR

2013-07-01

... processing. These include: Certain bulky wastes (e.g., combustible demolition and construction debris, tree... WASTES GUIDELINES FOR THE THERMAL PROCESSING OF SOLID WASTES Requirements and Recommended Procedures § 240.200-2 Recommended procedures: Design. (a) In addition to the residential and commercial wastes...

PI controller design for indirect vector controlled induction motor: A decoupling approach.

PubMed

Jain, Jitendra Kr; Ghosh, Sandip; Maity, Somnath; Dworak, Pawel

2017-09-01

Decoupling of the stator currents is important for smoother torque response of indirect vector controlled induction motors. Typically, feedforward decoupling is used to take care of current coupling that requires exact knowledge of motor parameters, additional circuitry and signal processing. In this paper, a method is proposed to design the regulating proportional-integral gains that minimize coupling without any requirement of the additional decoupler. The variation of the coupling terms for change in load torque is considered as the performance measure. An iterative linear matrix inequality based H ∞ control design approach is used to obtain the controller gains. A comparison between the feedforward and the proposed decoupling schemes is presented through simulation and experimental results. The results show that the proposed scheme is simple yet effective even without additional block or burden on signal processing. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

20 CFR 655.145 - Amendments to applications for temporary employment certification.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., DEPARTMENT OF LABOR TEMPORARY EMPLOYMENT OF FOREIGN WORKERS IN THE UNITED STATES Labor Certification Process... percent for employers requesting less than 10 workers) without requiring an additional recruitment period for U.S. workers. Requests for increases above the percent prescribed, without additional recruitment...

Using the theory of planned behavior to determine factors influencing processed foods consumption behavior.

PubMed

Seo, Sunhee; Kim, Og Yeon; Shim, Soonmi

2014-06-01

The purpose of this study is to identify how level of information affected intention, using the Theory of Planned Behavior. The study was conducted survey in diverse community centers and shopping malls in Seoul, which yielded N = 209 datasets. To compare processed foods consumption behavior, we divided samples into two groups based on level of information about food additives (whether respondents felt that information on food additives was sufficient or not). We analyzed differences in attitudes toward food additives and toward purchasing processed foods, subjective norms, perceived behavioral control, and behavioral intentions to processed foods between sufficient information group and lack information group. The results confirmed that more than 78% of respondents thought information on food additives was insufficient. However, the group who felt information was sufficient had more positive attitudes about consuming processed foods and behavioral intentions than the group who thought information was inadequate. This study found people who consider that they have sufficient information on food additives tend to have more positive attitudes toward processed foods and intention to consume processed foods. This study suggests increasing needs for nutrition education on the appropriate use of processed foods. Designing useful nutrition education requires a good understanding of factors which influence on processed foods consumption.

Using the theory of planned behavior to determine factors influencing processed foods consumption behavior

PubMed Central

Kim, Og Yeon; Shim, Soonmi

2014-01-01

BACKGROUND/OBJECTIVES The purpose of this study is to identify how level of information affected intention, using the Theory of Planned Behavior. SUBJECTS/METHODS The study was conducted survey in diverse community centers and shopping malls in Seoul, which yielded N = 209 datasets. To compare processed foods consumption behavior, we divided samples into two groups based on level of information about food additives (whether respondents felt that information on food additives was sufficient or not). We analyzed differences in attitudes toward food additives and toward purchasing processed foods, subjective norms, perceived behavioral control, and behavioral intentions to processed foods between sufficient information group and lack information group. RESULTS The results confirmed that more than 78% of respondents thought information on food additives was insufficient. However, the group who felt information was sufficient had more positive attitudes about consuming processed foods and behavioral intentions than the group who thought information was inadequate. This study found people who consider that they have sufficient information on food additives tend to have more positive attitudes toward processed foods and intention to consume processed foods. CONCLUSIONS This study suggests increasing needs for nutrition education on the appropriate use of processed foods. Designing useful nutrition education requires a good understanding of factors which influence on processed foods consumption. PMID:24944779

Biological Hydrogen Production: Simultaneous Saccharification and Fermentation with Nitrogen and Phosphorus Removal from Wastewater Effluent

DTIC Science & Technology

2010-07-29

bedirectly catalyzed tomonosaccharidesby cellulaseswithout requiring thermochemical pretreatment , aswould typically be required with lignocellulosic ...of a similar process with lignocellulosic biomass, although such biomass would likely require ther- mochemical pretreatment prior to enzymatic...by the automatic addition of 0.1 N NaOH . Total organic carbon (TOC), ammonia nitrogen, nitrate nitrogen, nitrite nitrogen and phosphorus analyses

DREAMS and IMAGE: A Model and Computer Implementation for Concurrent, Life-Cycle Design of Complex Systems

NASA Technical Reports Server (NTRS)

Hale, Mark A.; Craig, James I.; Mistree, Farrokh; Schrage, Daniel P.

1995-01-01

Computing architectures are being assembled that extend concurrent engineering practices by providing more efficient execution and collaboration on distributed, heterogeneous computing networks. Built on the successes of initial architectures, requirements for a next-generation design computing infrastructure can be developed. These requirements concentrate on those needed by a designer in decision-making processes from product conception to recycling and can be categorized in two areas: design process and design information management. A designer both designs and executes design processes throughout design time to achieve better product and process capabilities while expanding fewer resources. In order to accomplish this, information, or more appropriately design knowledge, needs to be adequately managed during product and process decomposition as well as recomposition. A foundation has been laid that captures these requirements in a design architecture called DREAMS (Developing Robust Engineering Analysis Models and Specifications). In addition, a computing infrastructure, called IMAGE (Intelligent Multidisciplinary Aircraft Generation Environment), is being developed that satisfies design requirements defined in DREAMS and incorporates enabling computational technologies.

Materials, Processes and Manufacturing in Ares 1 Upper Stage: Integration with Systems Design and Development

NASA Technical Reports Server (NTRS)

Bhat, Biliyar N.

2008-01-01

Ares I Crew Launch Vehicle Upper Stage is designed and developed based on sound systems engineering principles. Systems Engineering starts with Concept of Operations and Mission requirements, which in turn determine the launch system architecture and its performance requirements. The Ares I-Upper Stage is designed and developed to meet these requirements. Designers depend on the support from materials, processes and manufacturing during the design, development and verification of subsystems and components. The requirements relative to reliability, safety, operability and availability are also dependent on materials availability, characterization, process maturation and vendor support. This paper discusses the roles and responsibilities of materials and manufacturing engineering during the various phases of Ares IUS development, including design and analysis, hardware development, test and verification. Emphasis is placed how materials, processes and manufacturing support is integrated over the Upper Stage Project, both horizontally and vertically. In addition, the paper describes the approach used to ensure compliance with materials, processes, and manufacturing requirements during the project cycle, with focus on hardware systems design and development.

Development Challenges and Opportunities Confronting Economies in Transition

ERIC Educational Resources Information Center

Estes, Richard J.

2007-01-01

"Economies in Transition" (hereafter EIT or EITs) are countries in the process of shifting from "command" to "more open", liberalized, free market economic systems. In addition to achieving major structural adjustments to their economies, the transformational process requires the introduction of a high degree of…

Metered oxygen supply aids treatment of domestic sewage

NASA Technical Reports Server (NTRS)

Weliky, N.; Hooper, T. J.; Silverman, H. P.

1972-01-01

Microbiological fixed-bed process was developed in which supplementary oxygen required by microbial species is supplied by electrochemical device. Rate of addition of oxygen to waste treatment process is controlled to maintain aerobic metabolism and prevent anaerobic metabolisms which produce odorous or toxic products.

Harnessing the Big Data Paradigm for ICME: Shifting from Materials Selection to Materials Enabled Design

NASA Astrophysics Data System (ADS)

Broderick, Scott R.; Santhanam, Ganesh Ram; Rajan, Krishna

2016-08-01

As the size of databases has significantly increased, whether through high throughput computation or through informatics-based modeling, the challenge of selecting the optimal material for specific design requirements has also arisen. Given the multiple, and often conflicting, design requirements, this selection process is not as trivial as sorting the database for a given property value. We suggest that the materials selection process should minimize selector bias, as well as take data uncertainty into account. For this reason, we discuss and apply decision theory for identifying chemical additions to Ni-base alloys. We demonstrate and compare results for both a computational array of chemistries and standard commercial superalloys. We demonstrate how we can use decision theory to select the best chemical additions for enhancing both property and processing, which would not otherwise be easily identifiable. This work is one of the first examples of introducing the mathematical framework of set theory and decision analysis into the domain of the materials selection process.

Effect of Al(OH)3 on the sintering of UO2-Gd2O3 fuel pellets with addition of U3O8 from recycle

NASA Astrophysics Data System (ADS)

dos Santos, Lauro Roberto; Durazzo, Michelangelo; Urano de Carvalho, Elita Fontenele; Riella, Humberto Gracher

2017-09-01

The incorporation of gadolinium as burnable poison directly into nuclear fuel is important for reactivity compensation, which enables longer fuel cycles. The function of the burnable poison fuel is to control the neutron population in the reactor core during its startup and the beginning of the fuel burning cycle to extend the use of the fuel. The implementation of UO2-Gd2O3 poisoned fuel in Brazil has been proposed according to the future requirements established for the Angra-2 nuclear power plant. The UO2 powder used is produced from the Ammonium Uranyl Carbonate (AUC). The incorporation of Gd2O3 powder directly into the AUC-derived UO2 powder by dry mechanical blending is the most attractive process, because of its simplicity. Nevertheless, processing by this method leads to difficulties while obtaining sintered pellets with the minimum required density. The cause of the low densities is the bad sintering behavior of the UO2-Gd2O3 mixed fuel, which shows a blockage in the sintering process that hinders the densification. This effect has been overcome by microdoping of the fuel with small quantities of aluminum. The process for manufacturing the fuel inevitably generates uranium-rich scraps from various sources. This residue is reincorporated into the production process in the form of U3O8 powder additions. The addition of U3O8 also hinders densification in sintering. This study was carried out to investigate the influence of both aluminum and U3O8 additives on the density of fuel pellets after sintering. As the effects of these additives are counterposed, this work studied the combined effect thereof, seeking to find an applicable composition for the production process. The experimental results demonstrated the effectiveness of aluminum, in the form of Al(OH)3, as an additive to promote increase in the densification of the (U,Gd)O2 pellets during sintering, even with high additions of U3O8 recycled from the manufacturing process.

Software Design Methodology Migration for a Distributed Ground System

NASA Technical Reports Server (NTRS)

Ritter, George; McNair, Ann R. (Technical Monitor)

2002-01-01

The Marshall Space Flight Center's (MSFC) Payload Operations Center (POC) ground system has been developed and has evolved over a period of about 10 years. During this time the software processes have migrated from more traditional to more contemporary development processes. The new Software processes still emphasize requirements capture, software configuration management, design documenting, and making sure the products that have been developed are accountable to initial requirements. This paper will give an overview of how the Software Process have evolved highlighting the positives as well as the negatives. In addition, we will mention the COTS tools that have been integrated into the processes and how the COTS have provided value to the project .

Development of water quality standards criteria. [for consumables (spacecrew supplies)

NASA Technical Reports Server (NTRS)

1976-01-01

Qualitative and semiquantitative analyses were made of volatile organic compounds in water supplies collected at various stages of processing in the space station prototype vacuum compression distillation unit to evaluate the process and the product water. Additional evaluation was made of specific ingredients required to adequately enhance the taste of the reclaimed water. A concept for the in-flight addition of these ingredients was developed. Revisions to previously recommended potable water criteria and specifications are included.

Solution-processed flexible NiO resistive random access memory device

NASA Astrophysics Data System (ADS)

Kim, Soo-Jung; Lee, Heon; Hong, Sung-Hoon

2018-04-01

Non-volatile memories (NVMs) using nanocrystals (NCs) as active materials can be applied to soft electronic devices requiring a low-temperature process because NCs do not require a heat treatment process for crystallization. In addition, memory devices can be implemented simply by using a patterning technique using a solution process. In this study, a flexible NiO ReRAM device was fabricated using a simple NC patterning method that controls the capillary force and dewetting of a NiO NC solution at low temperature. The switching behavior of a NiO NC based memory was clearly observed by conductive atomic force microscopy (c-AFM).

25 CFR 517.4 - Requirements for making requests.

Code of Federal Regulations, 2010 CFR

2010-04-01

... INFORMATION ACT PROCEDURES § 517.4 Requirements for making requests. (a) How to make a FOIA request. Requests... additional information. If the requester is making a request for records about another individual, the..., the requester will be notified of this decision and advised that fees associated with the processing...

46 CFR 54.30-15 - Requirement for analysis and computation.

Code of Federal Regulations, 2010 CFR

2010-10-01

... PRESSURE VESSELS Mechanical Stress Relief § 54.30-15 Requirement for analysis and computation. (a) A stress... mechanical stress relief process. This analysis should include consideration of the local stresses in way of saddles or other supporting structure and additional bending stresses due to the weight of the...

75 FR 72964 - Disapproval and Promulgation of Air Quality Implementation Plans; Indiana; Addition of Incentive...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-29

... limits, and the processing of pollution prevention projects as minor permit revisions. EPA proposed to... standard. EPA is disapproving the third incentive, which affects public notice requirements for pollution prevention projects, because it relaxes the existing SIP-approved public notice requirements and is...

24 CFR 3286.207 - Process for obtaining installation license.

Code of Federal Regulations, 2010 CFR

2010-04-01

... installation license must submit verification of the experience required in § 3286.205(a). This verification may be in the form of statements by past or present employers or a self-certification that the applicant meets those experience requirements, but HUD may contact the applicant for additional verification...

24 CFR 3286.307 - Process for obtaining trainer's qualification.

Code of Federal Regulations, 2010 CFR

2010-04-01

... verification of the experience required in § 3286.305. This verification may be in the form of statements by past or present employers or a self-certification that the applicant meets those experience requirements, but HUD may contact the applicant for additional verification at any time. The applicant must...

40 CFR 63.867 - Reporting requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Emission Standards for Hazardous Air Pollutants for Chemical Recovery Combustion Sources at Kraft, Soda...) Additional reporting requirements for HAP metals standards. (1) Any owner or operator of a group of process units in a chemical recovery system at a mill complying with the PM emissions limits in § 63.862(a)(1...

40 CFR 63.867 - Reporting requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Emission Standards for Hazardous Air Pollutants for Chemical Recovery Combustion Sources at Kraft, Soda...) Additional reporting requirements for HAP metals standards. (1) Any owner or operator of a group of process units in a chemical recovery system at a mill complying with the PM emissions limits in § 63.862(a)(1...

40 CFR 63.867 - Reporting requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Emission Standards for Hazardous Air Pollutants for Chemical Recovery Combustion Sources at Kraft, Soda...) Additional reporting requirements for HAP metals standards. (1) Any owner or operator of a group of process units in a chemical recovery system at a mill complying with the PM emissions limits in § 63.862(a)(1...

46 CFR 54.30-15 - Requirement for analysis and computation.

Code of Federal Regulations, 2012 CFR

2012-10-01

... PRESSURE VESSELS Mechanical Stress Relief § 54.30-15 Requirement for analysis and computation. (a) A stress... mechanical stress relief process. This analysis should include consideration of the local stresses in way of saddles or other supporting structure and additional bending stresses due to the weight of the...

46 CFR 54.30-15 - Requirement for analysis and computation.

Code of Federal Regulations, 2014 CFR

2014-10-01

... PRESSURE VESSELS Mechanical Stress Relief § 54.30-15 Requirement for analysis and computation. (a) A stress... mechanical stress relief process. This analysis should include consideration of the local stresses in way of saddles or other supporting structure and additional bending stresses due to the weight of the...

46 CFR 54.30-15 - Requirement for analysis and computation.

Code of Federal Regulations, 2013 CFR

2013-10-01

... PRESSURE VESSELS Mechanical Stress Relief § 54.30-15 Requirement for analysis and computation. (a) A stress... mechanical stress relief process. This analysis should include consideration of the local stresses in way of saddles or other supporting structure and additional bending stresses due to the weight of the...

21 CFR 640.11 - General requirements.

Code of Federal Regulations, 2012 CFR

2012-04-01

... ADDITIONAL STANDARDS FOR HUMAN BLOOD AND BLOOD PRODUCTS Red Blood Cells § 640.11 General requirements. (a) Storage. Immediately after processing, the Red Blood Cells shall be placed in storage and maintained at a... there is any abnormality in color or physical appearance or if there is any indication of microbial...

21 CFR 640.11 - General requirements.

Code of Federal Regulations, 2014 CFR

2014-04-01

... ADDITIONAL STANDARDS FOR HUMAN BLOOD AND BLOOD PRODUCTS Red Blood Cells § 640.11 General requirements. (a) Storage. Immediately after processing, the Red Blood Cells shall be placed in storage and maintained at a... there is any abnormality in color or physical appearance or if there is any indication of microbial...

21 CFR 640.11 - General requirements.

Code of Federal Regulations, 2011 CFR

2011-04-01

... ADDITIONAL STANDARDS FOR HUMAN BLOOD AND BLOOD PRODUCTS Red Blood Cells § 640.11 General requirements. (a) Storage. Immediately after processing, the Red Blood Cells shall be placed in storage and maintained at a... there is any abnormality in color or physical appearance or if there is any indication of microbial...

21 CFR 640.11 - General requirements.

Code of Federal Regulations, 2013 CFR

2013-04-01

... ADDITIONAL STANDARDS FOR HUMAN BLOOD AND BLOOD PRODUCTS Red Blood Cells § 640.11 General requirements. (a) Storage. Immediately after processing, the Red Blood Cells shall be placed in storage and maintained at a... there is any abnormality in color or physical appearance or if there is any indication of microbial...

46 CFR 54.30-15 - Requirement for analysis and computation.

Code of Federal Regulations, 2011 CFR

2011-10-01

... PRESSURE VESSELS Mechanical Stress Relief § 54.30-15 Requirement for analysis and computation. (a) A stress... mechanical stress relief process. This analysis should include consideration of the local stresses in way of saddles or other supporting structure and additional bending stresses due to the weight of the...

Regional Needs Analysis Report. 2011

ERIC Educational Resources Information Center

Washington Higher Education Coordinating Board, 2011

2011-01-01

The Higher Education Coordinating Board (HECB) is required to develop a comprehensive and ongoing needs assessment process to analyze demand for additional degrees and programs [RCW 28B.76.230 (1)]. This report fulfills a portion of that mandate by focusing on employer demand on the regional level, but also includes additional information on…

21 CFR 172.177 - Sodium nitrite used in processing smoked chub.

Code of Federal Regulations, 2014 CFR

2014-04-01

... provides a monitoring system positioned in as many strategic locations in the smokehouse as necessary to... containers, retail packages, and shipping records shall indicate with appropriate notice the perishable... container shall bear, in addition to the other information required by the Act, the name of the additive. (2...

15 CFR 713.4 - Advance declaration requirements for additionally planned production, processing, or consumption...

Code of Federal Regulations, 2013 CFR

2013-01-01

...) You plan to increase the production, processing, or consumption of a Schedule 2 chemical by a plant... production, processing, or consumption of a Schedule 2 chemical by a declared plant site by 20 percent or... multipurpose activities; (v) Changes to the plant site's status relating to domestic transfer of the chemical...

15 CFR 713.4 - Advance declaration requirements for additionally planned production, processing, or consumption...

Code of Federal Regulations, 2014 CFR

2014-01-01

...) You plan to increase the production, processing, or consumption of a Schedule 2 chemical by a plant... production, processing, or consumption of a Schedule 2 chemical by a declared plant site by 20 percent or... multipurpose activities; (v) Changes to the plant site's status relating to domestic transfer of the chemical...

15 CFR 713.4 - Advance declaration requirements for additionally planned production, processing, or consumption...

Code of Federal Regulations, 2012 CFR

2012-01-01

...) You plan to increase the production, processing, or consumption of a Schedule 2 chemical by a plant... production, processing, or consumption of a Schedule 2 chemical by a declared plant site by 20 percent or... multipurpose activities; (v) Changes to the plant site's status relating to domestic transfer of the chemical...

40 CFR 60.480 - Applicability and designation of affected facility.

Code of Federal Regulations, 2010 CFR

2010-07-01

... subpart. (c) Addition or replacement of equipment for the purpose of process improvement which is... all equipment (defined in § 60.481) within a process unit is an affected facility. (b) Any affected... the definition of “process unit” in § 60.481 and the requirements in § 60.482-1(g) of this subpart...

DATA QUALITY OBJECTIVES FOR SELECTING WASTE SAMPLES FOR BENCH-SCALE REFORMER TREATABILITY STUDIES

DOE Office of Scientific and Technical Information (OSTI.GOV)

BANNING DL

2011-02-11

This document describes the data quality objectives to select archived samples located at the 222-S Laboratory for Bench-Scale Reforming testing. The type, quantity, and quality of the data required to select the samples for Fluid Bed Steam Reformer testing are discussed. In order to maximize the efficiency and minimize the time to treat Hanford tank waste in the Waste Treatment and Immobilization Plant, additional treatment processes may be required. One of the potential treatment processes is the fluidized bed steam reformer. A determination of the adequacy of the fluidized bed steam reformer process to treat Hanford tank waste is required.more » The initial step in determining the adequacy of the fluidized bed steam reformer process is to select archived waste samples from the 222-S Laboratory that will be used in a bench scale tests. Analyses of the selected samples will be required to confirm the samples meet the shipping requirements and for comparison to the bench scale reformer (BSR) test sample selection requirements.« less

Software Development and Test Methodology for a Distributed Ground System

NASA Technical Reports Server (NTRS)

Ritter, George; Guillebeau, Pat; McNair, Ann R. (Technical Monitor)

2002-01-01

The Marshall Space Flight Center's (MSFC) Payload Operations Center (POC) ground system has evolved over a period of about 10 years. During this time the software processes have migrated from more traditional to more contemporary development processes in an effort to minimize unnecessary overhead while maximizing process benefits. The Software processes that have evolved still emphasize requirements capture, software configuration management, design documenting, and making sure the products that have been developed are accountable to initial requirements. This paper will give an overview of how the Software Processes have evolved, highlighting the positives as well as the negatives. In addition, we will mention the COTS tools that have been integrated into the processes and how the COTS have provided value to the project.

The Intersection of Information and Science Literacy

ERIC Educational Resources Information Center

Klucevsek, Kristin

2017-01-01

To achieve higher science literacy, both students and the public require discipline-specific information literacy in the sciences. Scientific information literacy is a core component of the scientific process. In addition to teaching how to find and evaluate resources, scientific information literacy should include teaching the process of…

Crew interface specifications preparation for in-flight maintenance and stowage functions

NASA Technical Reports Server (NTRS)

Parker, F. W.; Carlton, B. E.

1972-01-01

The findings and data products developed during the Phase 2 crew interface specification study are presented. Five new NASA general specifications were prepared: operations location coding system for crew interfaces; loose equipment and stowage management requirements; loose equipment and stowage data base information requirements; spacecraft loose equipment stowage drawing requirements; and inflight stowage management data requirements. Additional data was developed defining inflight maintenance processes and related data concepts for inflight troubleshooting, remove/repair/replace and scheduled maintenance activities. The process of maintenance task and equipment definition during spacecraft design and development was also defined and related data concepts were identified for futher development into formal NASA specifications during future follow-on study phases of the contract.

Preliminary report of the discovery of a new pharmaceutical granulation process using foamed aqueous binders.

PubMed

Keary, Colin M; Sheskey, Paul J

2004-09-01

Spray granulation is commonly used to improve the flow of drug formulation powders by adding liquid binders. We have discovered a new granulation process whereby liquid binders are added as aqueous foam. Initial experiments indicate that foam granulations require less binder than spray granulations, less water is added to the powder mass, rates of addition of foam can be greater than rates of addition of sprayed liquids, and foam can be added in a single batch to the surface of the powder mass for incorporation at some later stage in the process. This new process appears to have no detrimental effects on granulate, tablet, or in vitro drug dissolution properties. In addition, the elimination of spray addition reduces the complexity of the process and avoids the plugging problems associated with spray nozzles. Several formulations were successfully scaled up from laboratory scale (1.5 kg) to pilot scale (15 kg). Process control was good and there was no detrimental effect on tablet and drug dissolution properties. This paper also proposes a working hypothesis of the mechanism by which foam granulation operates.

The Algorithm Theoretical Basis Document for Level 1A Processing

NASA Technical Reports Server (NTRS)

Jester, Peggy L.; Hancock, David W., III

2012-01-01

The first process of the Geoscience Laser Altimeter System (GLAS) Science Algorithm Software converts the Level 0 data into the Level 1A Data Products. The Level 1A Data Products are the time ordered instrument data converted from counts to engineering units. This document defines the equations that convert the raw instrument data into engineering units. Required scale factors, bias values, and coefficients are defined in this document. Additionally, required quality assurance and browse products are defined in this document.

Model-based Assessment for Balancing Privacy Requirements and Operational Capabilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Knirsch, Fabian; Engel, Dominik; Frincu, Marc

2015-02-17

The smart grid changes the way energy is produced and distributed. In addition both, energy and information is exchanged bidirectionally among participating parties. Therefore heterogeneous systems have to cooperate effectively in order to achieve a common high-level use case, such as smart metering for billing or demand response for load curtailment. Furthermore, a substantial amount of personal data is often needed for achieving that goal. Capturing and processing personal data in the smart grid increases customer concerns about privacy and in addition, certain statutory and operational requirements regarding privacy aware data processing and storage have to be met. An increasemore » of privacy constraints, however, often limits the operational capabilities of the system. In this paper, we present an approach that automates the process of finding an optimal balance between privacy requirements and operational requirements in a smart grid use case and application scenario. This is achieved by formally describing use cases in an abstract model and by finding an algorithm that determines the optimum balance by forward mapping privacy and operational impacts. For this optimal balancing algorithm both, a numeric approximation and – if feasible – an analytic assessment are presented and investigated. The system is evaluated by applying the tool to a real-world use case from the University of Southern California (USC) microgrid.« less

How to Apply | Cancer Prevention Fellowship Program

Cancer.gov

To be considered for the program, you must meet the eligibility requirements and complete all parts of the application, as described below. If you have additional questions about the application process, please contact our office. You must apply through our online application process. When applying, you will be asked to:

Demonstration Bulletin. Membrane Microfiltration. E. I. DuPont de Nemours and Company, Inc. Oberlin Filter Company

EPA Science Inventory

The DuPont/Oberlin microfiltration technology is a physical separation process that removes solid particles from liquid wastes. The process can filter particles that are submicron or larger in diameter. Pretreatment, such as chemical additions, will be required if dissolved con...

The Role of Attention in Item-Item Binding in Visual Working Memory

ERIC Educational Resources Information Center

Peterson, Dwight J.; Naveh-Benjamin, Moshe

2017-01-01

An important yet unresolved question regarding visual working memory (VWM) relates to whether or not binding processes within VWM require additional attentional resources compared with processing solely the individual components comprising these bindings. Previous findings indicate that binding of surface features (e.g., colored shapes) within VWM…

31 CFR 203.9 - Scope of the subpart.

Code of Federal Regulations, 2014 CFR

2014-07-01

... rules that financial institutions must follow when they process electronic Federal tax payment transactions. A financial institution is not required to be designated as a TT&L depositary in order to process electronic Federal tax payments. In addition, a financial institution does not become a TT&L depositary by...

75 FR 27561 - Agency Recordkeeping/Reporting Requirements Under Emergency Review by the Office of Management...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-17

... authorize emergency processing of its information collection clearance of the LIHEAP Program Integrity... approval for this information collection under procedures for emergency processing by May 30, 2010. A copy... has determined that additional information from each administering agency is necessary to assess...

5 CFR 1631.8 - Prompt response.

Code of Federal Regulations, 2010 CFR

2010-01-01

... so advise the requester within 5 work days. The time limit for processing such a request will not... receipt of the request, unless additional time is required for one of the following reasons: (1) It is... the office processing the request (e.g., the record keeper); (2) It is necessary to search for...

38 CFR 74.11 - How does CVE process applications for VetBiz VIP Verification Program?

Code of Federal Regulations, 2012 CFR

2012-07-01

... electronic means. (The Office of Management and Budget has approved the information collection requirements... Veterans Enterprise, is authorized to approve or deny applications for VetBiz VIP Verification. The CVE... complete and suitable for evaluation and, if not, what additional information or clarification is required...

38 CFR 74.11 - How does CVE process applications for VetBiz VIP Verification Program?

Code of Federal Regulations, 2010 CFR

2010-07-01

... electronic means. (The Office of Management and Budget has approved the information collection requirements... Veterans Enterprise, is authorized to approve or deny applications for VetBiz VIP Verification. The CVE... complete and suitable for evaluation and, if not, what additional information or clarification is required...

38 CFR 74.11 - How does CVE process applications for VetBiz VIP Verification Program?

Code of Federal Regulations, 2011 CFR

2011-07-01

... electronic means. (The Office of Management and Budget has approved the information collection requirements... Veterans Enterprise, is authorized to approve or deny applications for VetBiz VIP Verification. The CVE... complete and suitable for evaluation and, if not, what additional information or clarification is required...

38 CFR 74.11 - How does CVE process applications for VetBiz VIP Verification Program?

Code of Federal Regulations, 2014 CFR

2014-07-01

... electronic means. (The Office of Management and Budget has approved the information collection requirements... Veterans Enterprise, is authorized to approve or deny applications for VetBiz VIP Verification. The CVE... complete and suitable for evaluation and, if not, what additional information or clarification is required...

38 CFR 74.11 - How does CVE process applications for VetBiz VIP Verification Program?

Code of Federal Regulations, 2013 CFR

2013-07-01

... electronic means. (The Office of Management and Budget has approved the information collection requirements... Veterans Enterprise, is authorized to approve or deny applications for VetBiz VIP Verification. The CVE... complete and suitable for evaluation and, if not, what additional information or clarification is required...

Secreted Immunodominant Mycobacterium tuberculosis Antigens Are Processed by the Cytosolic Pathway

PubMed Central

Grotzke, Jeff E.; Siler, Anne C.; Lewinsohn, Deborah A.; Lewinsohn, David M.

2010-01-01

Exposure to Mycobacterium tuberculosis can result in lifelong but asymptomatic infection in most individuals. Although CD8+ T cells are elicited at high frequencies over the course of infection in both humans and mice, how phagosomal M. tuberculosis Ags are processed and presented by MHC class I molecules is poorly understood. Broadly, both cytosolic and noncytosolic pathways have been described. We have previously characterized the presentation of three HLA-I epitopes from M. tuberculosis and shown that these Ags are processed in the cytosol, whereas others have demonstrated noncytosolic presentation of the 19-kDa lipoprotein as well as apoptotic bodies from M. tuberculosis-infected cells. In this paper, we now characterize the processing pathway in an additional six M. tuberculosis epitopes from four proteins in human dendritic cells. Addition of the endoplasmic reticulum-Golgi trafficking inhibitor, brefeldin A, resulted in complete abrogation of Ag processing consistent with cytosolic presentation. However, although addition of the proteasome inhibitor epoxomicin blocked the presentation of two epitopes, presentation of four epitopes was enhanced. To further examine the requirement for proteasomal processing of an epoxomicin-enhanced epitope, an in vitro proteasome digestion assay was established. We find that the proteasome does indeed generate the epitope and that epitope generation is enhanced in the presence of epoxomicin. To further confirm that both the epoxomicin-inhibited and epoxomicin-enhanced epitopes are processed cytosolically, we demonstrate that TAP transport and new protein synthesis are required for presentation. Taken together, these data demonstrate that immunodominant M. tuberculosis CD8+ Ags are processed and presented using a cytosolic pathway. PMID:20802151

Needs Assessment for the Use of NASA Remote Sensing Data in the Development and Implementation of Estuarine and Coastal Water Quality Standards

NASA Technical Reports Server (NTRS)

Spiering, Bruce; Underwood, Lauren; Ellis, Chris; Lehrter, John; Hagy, Jim; Schaeffer, Blake

2010-01-01

The goals of the project are to provide information from satellite remote sensing to support numeric nutrient criteria development and to determine data processing methods and data quality requirements to support nutrient criteria development and implementation. The approach is to identify water quality indicators that are used by decision makers to assess water quality and that are related to optical properties of the water; to develop remotely sensed data products based on algorithms relating remote sensing imagery to field-based observations of indicator values; to develop methods to assess estuarine water quality, including trends, spatial and temporal variability, and seasonality; and to develop tools to assist in the development and implementation of estuarine and coastal nutrient criteria. Additional slides present process, criteria development, typical data sources and analyses for criteria process, the power of remote sensing data for the process, examples from Pensacola Bay, spatial and temporal variability, pixel matchups, remote sensing validation, remote sensing in coastal waters, requirements for remotely sensed data products, and needs assessment. An additional presentation examines group engagement and information collection. Topics include needs assessment purpose and objectives, understanding water quality decision making, determining information requirements, and next steps.

Potential Air Pollutant Emissions and Permitting Classifications for Two Biorefinery Process Designs in the United States

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eberle, Annika; Bhatt, Arpit; Zhang, Yimin

Advanced biofuel production facilities (biorefineries), such as those envisioned by the United States (U.S.) Renewable Fuel Standard and U.S. Department of Energy's research and development programs, often lack historical air pollutant emissions data, which can pose challenges for obtaining air emission permits that are required for construction and operation. To help fill this knowledge gap, we perform a thorough regulatory analysis and use engineering process designs to assess the applicability of federal air regulations and quantify air pollutant emissions for two feasibility-level biorefinery designs. We find that without additional emission-control technologies both biorefineries would likely be required to obtain majormore » source permits under the Clean Air Act's New Source Review program. The permitting classification (so-called 'major' or 'minor') has implications for the time and effort required for permitting and therefore affects the cost of capital and the fuel selling price. Consequently, we explore additional technically feasible emission-control technologies and process modifications that have the potential to reduce emissions to achieve a minor source permitting classification. Finally, our analysis of air pollutant emissions and controls can assist biorefinery developers with the air permitting process and inform regulatory agencies about potential permitting pathways for novel biorefinery designs.« less

Potential Air Pollutant Emissions and Permitting Classifications for Two Biorefinery Process Designs in the United States

DOE PAGES

Eberle, Annika; Bhatt, Arpit; Zhang, Yimin; ...

2017-04-26

Advanced biofuel production facilities (biorefineries), such as those envisioned by the United States (U.S.) Renewable Fuel Standard and U.S. Department of Energy's research and development programs, often lack historical air pollutant emissions data, which can pose challenges for obtaining air emission permits that are required for construction and operation. To help fill this knowledge gap, we perform a thorough regulatory analysis and use engineering process designs to assess the applicability of federal air regulations and quantify air pollutant emissions for two feasibility-level biorefinery designs. We find that without additional emission-control technologies both biorefineries would likely be required to obtain majormore » source permits under the Clean Air Act's New Source Review program. The permitting classification (so-called 'major' or 'minor') has implications for the time and effort required for permitting and therefore affects the cost of capital and the fuel selling price. Consequently, we explore additional technically feasible emission-control technologies and process modifications that have the potential to reduce emissions to achieve a minor source permitting classification. Finally, our analysis of air pollutant emissions and controls can assist biorefinery developers with the air permitting process and inform regulatory agencies about potential permitting pathways for novel biorefinery designs.« less

Potential Air Pollutant Emissions and Permitting Classifications for Two Biorefinery Process Designs in the United States.

PubMed

Eberle, Annika; Bhatt, Arpit; Zhang, Yimin; Heath, Garvin

2017-06-06

Advanced biofuel production facilities (biorefineries), such as those envisioned by the United States (U.S.) Renewable Fuel Standard and U.S. Department of Energy's research and development programs, often lack historical air pollutant emissions data, which can pose challenges for obtaining air emission permits that are required for construction and operation. To help fill this knowledge gap, we perform a thorough regulatory analysis and use engineering process designs to assess the applicability of federal air regulations and quantify air pollutant emissions for two feasibility-level biorefinery designs. We find that without additional emission-control technologies both biorefineries would likely be required to obtain major source permits under the Clean Air Act's New Source Review program. The permitting classification (so-called "major" or "minor") has implications for the time and effort required for permitting and therefore affects the cost of capital and the fuel selling price. Consequently, we explore additional technically feasible emission-control technologies and process modifications that have the potential to reduce emissions to achieve a minor source permitting classification. Our analysis of air pollutant emissions and controls can assist biorefinery developers with the air permitting process and inform regulatory agencies about potential permitting pathways for novel biorefinery designs.

7 CFR 944.312 - Orange import regulation.

Code of Federal Regulations, 2010 CFR

2010-01-01

... preserved by any commercial process, including canning, freezing, dehydrating, drying, and the addition of chemical substances, or by fermentation. (d) Terms and tolerances pertaining to grade and size requirements...

Influence of processing factors over concrete strength.

NASA Astrophysics Data System (ADS)

Kara, K. A.; Dolzhenko, A. V.; Zharikov, I. S.

2018-03-01

Construction of facilities of cast in-situ reinforced concrete poses additional requirements to quality of material, peculiarities of the construction process may sometimes lead to appearance of lamination planes and inhomogeneity of concrete, which reduce strength of the material and structure as a whole. Technology compliance while working with cast in-situ concrete has a significant impact onto the concrete strength. Such process factors as concrete curing, vibration and compaction of the concrete mixture, temperature treatment, etc., when they are countered or inadequately followed lead to a significant reduction in concrete strength. Here, the authors experimentally quantitatively determine the loss of strength in in-situ cast concrete structures due to inadequate following of process requirements, in comparison with full compliance.

A Theory of Information Quality and a Framework for its Implementation in the Requirements Engineering Process

NASA Astrophysics Data System (ADS)

Grenn, Michael W.

This dissertation introduces a theory of information quality to explain macroscopic behavior observed in the systems engineering process. The theory extends principles of Shannon's mathematical theory of communication [1948] and statistical mechanics to information development processes concerned with the flow, transformation, and meaning of information. The meaning of requirements information in the systems engineering context is estimated or measured in terms of the cumulative requirements quality Q which corresponds to the distribution of the requirements among the available quality levels. The requirements entropy framework (REF) implements the theory to address the requirements engineering problem. The REF defines the relationship between requirements changes, requirements volatility, requirements quality, requirements entropy and uncertainty, and engineering effort. The REF is evaluated via simulation experiments to assess its practical utility as a new method for measuring, monitoring and predicting requirements trends and engineering effort at any given time in the process. The REF treats the requirements engineering process as an open system in which the requirements are discrete information entities that transition from initial states of high entropy, disorder and uncertainty toward the desired state of minimum entropy as engineering effort is input and requirements increase in quality. The distribution of the total number of requirements R among the N discrete quality levels is determined by the number of defined quality attributes accumulated by R at any given time. Quantum statistics are used to estimate the number of possibilities P for arranging R among the available quality levels. The requirements entropy H R is estimated using R, N and P by extending principles of information theory and statistical mechanics to the requirements engineering process. The information I increases as HR and uncertainty decrease, and the change in information AI needed to reach the desired state of quality is estimated from the perspective of the receiver. The HR may increase, decrease or remain steady depending on the degree to which additions, deletions and revisions impact the distribution of R among the quality levels. Current requirements trend metrics generally treat additions, deletions and revisions the same and simply measure the quantity of these changes over time. The REF evaluates the quantity of requirements changes over time, distinguishes between their positive and negative effects by calculating their impact on HR, Q, and AI, and forecasts when the desired state will be reached, enabling more accurate assessment of the status and progress of the requirements engineering effort. Results from random variable simulations suggest the REF is an improved leading indicator of requirements trends that can be readily combined with current methods. The increase in I, or decrease in H R and uncertainty, is proportional to the engineering effort E input into the requirements engineering process. The REF estimates the AE needed to transition R from their current state of quality to the desired end state or some other interim state of interest. Simulation results are compared with measured engineering effort data for Department of Defense programs published in the SE literature, and the results suggest the REF is a promising new method for estimation of AE.

Experimental study on combined cold forging process of backward cup extrusion and piercing

NASA Astrophysics Data System (ADS)

Henry, Robinson; Liewald, Mathias

2018-05-01

A reduction in material usage of cold forged components while maintaining the functional requirements can be achieved using hollow or tubular preforms. These preforms are used to meet lightweight requirements and to decrease production costs of cold formed components. To increase production efficiency in common multi-stage cold forming processes, manufacturing of hollow preforms by combining the processes backward cup extrusion and piercing was established and will be discussed in this paper. Corresponding investigations and experimental studies are reported in this article. The objectives of the experimental investigations have been the detection of significant process parameters, determination of process limits for the combined processes and validation of the numerical investigations. In addition, the general influence concerning surface quality and diameter tolerance of hollow performs are discussed in this paper. The final goal is to summarize a guideline for industrial application, moreover, to transfer the knowledge to industry, as regards what are required part geometries to reduce the number of forming stages as well as tool cost.

[Status and suggestions for adjuvant standard for Chinese materia medica processing in China].

PubMed

Yang, Chun-Yu; Cao, Hui; Wang, Xiao-Tao; Tu, Jia-Sheng; Qian, Zhong-Zhi; Yu, Zhi-Ling; Shang, Yue; Zhang, Bao-Xian

2017-04-01

In this paper, the status of adjuvant standard for Chinese materia medica processing in the Chinese Pharmacopoeia 2015 edition, the National Specification of Chinese Materia Medica Processing, and the 29 provincial specification of Chinese materia medica was summarized, and the the status including general requirements, specific requirements, and quality standard in the three grade official specifications was collected and analyzed according to the "medicine-adjuvant homology" and "food-adjuvant homology" features of adjuvants. This paper also introduced the research situation of adjuvant standard for Chinese materia medica processing in China; In addition, analyzed and discussed the problems existing in the standard system of adjuvant for Chinese materia medica processing, such as lack of general requirements, low level of standard, inconsistent standard references, and lack of research on the standard, and provided suggestions for the further establishment of the national standards system of adjuvant for Chinese materia medica processing. Copyright© by the Chinese Pharmaceutical Association.

Electrical Bonding: A Survey of Requirement, Methods, and Specifications

NASA Technical Reports Server (NTRS)

Evans, R. W.

1998-01-01

This document provides information helpful to engineers imposing electrical bonding requirements, reviewing waiver requests, or modifying specifications on various space programs. Electrical bonding specifications and some of the processes used in the United States have been reviewed. This document discusses the specifications, the types of bonds, the intent of each, and the basic requirements where possible. Additional topics discussed are resistance versus impedance, bond straps, corrosion, finishes, and special applications.

How verbal and spatial manipulation networks contribute to calculation: an fMRI study.

PubMed

Zago, Laure; Petit, Laurent; Turbelin, Marie-Renée; Andersson, Frédéric; Vigneau, Mathieu; Tzourio-Mazoyer, Nathalie

2008-01-01

The manipulation of numbers required during calculation is known to rely on working memory (WM) resources. Here, we investigated the respective contributions of verbal and/or spatial WM manipulation brain networks during the addition of four numbers performed by adults, using functional magnetic resonance imaging (fMRI). Both manipulation and maintenance tasks were proposed with syllables, locations, or two-digit numbers. As compared to their maintenance, numbers manipulation (addition) elicited increased activation within a widespread cortical network including inferior temporal, parietal, and prefrontal regions. Our results demonstrate that mastery of arithmetic calculation requires the cooperation of three WM manipulation systems: an executive manipulation system conjointly recruited by the three manipulation tasks, including the anterior cingulate cortex (ACC), the orbital part of the inferior frontal gyrus, and the caudate nuclei; a left-lateralized, language-related, inferior fronto-temporal system elicited by numbers and syllables manipulation tasks required for retrieval, selection, and association of symbolic information; and a right superior and posterior fronto-parietal system elicited by numbers and locations manipulation tasks for spatial WM and attentional processes. Our results provide new information that the anterior intraparietal sulcus (IPS) is involved in tasks requiring a magnitude processing with symbolic (numbers) and nonsymbolic (locations) stimuli. Furthermore, the specificity of arithmetic processing is mediated by a left-hemispheric specialization of the anterior and posterior parts of the IPS as compared to a spatial task involving magnitude processing with nonsymbolic material.

The Economics of Big Area Addtiive Manufacturing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Post, Brian; Lloyd, Peter D; Lindahl, John

Case studies on the economics of Additive Manufacturing (AM) suggest that processing time is the dominant cost in manufacturing. Most additive processes have similar performance metrics: small part sizes, low production rates and expensive feedstocks. Big Area Additive Manufacturing is based on transitioning polymer extrusion technology from a wire to a pellet feedstock. Utilizing pellets significantly increases deposition speed and lowers material cost by utilizing low cost injection molding feedstock. The use of carbon fiber reinforced polymers eliminates the need for a heated chamber, significantly reducing machine power requirements and size constraints. We hypothesize that the increase in productivity coupledmore » with decrease in feedstock and energy costs will enable AM to become more competitive with conventional manufacturing processes for many applications. As a test case, we compare the cost of using traditional fused deposition modeling (FDM) with BAAM for additively manufacturing composite tooling.« less

A generic template for automated bioanalytical ligand-binding assays using modular robotic scripts in support of discovery biotherapeutic programs.

PubMed

Duo, Jia; Dong, Huijin; DeSilva, Binodh; Zhang, Yan J

2013-07-01

Sample dilution and reagent pipetting are time-consuming steps in ligand-binding assays (LBAs). Traditional automation-assisted LBAs use assay-specific scripts that require labor-intensive script writing and user training. Five major script modules were developed on Tecan Freedom EVO liquid handling software to facilitate the automated sample preparation and LBA procedure: sample dilution, sample minimum required dilution, standard/QC minimum required dilution, standard/QC/sample addition, and reagent addition. The modular design of automation scripts allowed the users to assemble an automated assay with minimal script modification. The application of the template was demonstrated in three LBAs to support discovery biotherapeutic programs. The results demonstrated that the modular scripts provided the flexibility in adapting to various LBA formats and the significant time saving in script writing and scientist training. Data generated by the automated process were comparable to those by manual process while the bioanalytical productivity was significantly improved using the modular robotic scripts.

3-D laser patterning process utilizing horizontal and vertical patterning

DOEpatents

Malba, Vincent; Bernhardt, Anthony F.

2000-01-01

A process which vastly improves the 3-D patterning capability of laser pantography (computer controlled laser direct-write patterning). The process uses commercially available electrodeposited photoresist (EDPR) to pattern 3-D surfaces. The EDPR covers the surface of a metal layer conformally, coating the vertical as well as horizontal surfaces. A laser pantograph then patterns the EDPR, which is subsequently developed in a standard, commercially available developer, leaving patterned trench areas in the EDPR. The metal layer thereunder is now exposed in the trench areas and masked in others, and thereafter can be etched to form the desired pattern (subtractive process), or can be plated with metal (additive process), followed by a resist stripping, and removal of the remaining field metal (additive process). This improved laser pantograph process is simpler, faster, move manufacturable, and requires no micro-machining.

32 CFR 1803.21 - Receipt, recording, and tasking.

Code of Federal Regulations, 2010 CFR

2010-07-01

... tasking. The Information and Privacy Coordinator shall within ten (10) days record each mandatory.... Additional taskings, as required during the review process, shall be accomplished within ten (10) days of...

Nitrogen removal by recycle water nitritation as an attractive alternative for retrofit technologies in municipal wastewater treatment plants.

PubMed

Gil, K I; Choi, E

2004-01-01

The recycle water from sludge processing in municipal wastewater treatment plants causes many serious problems in the efficiency and stability of the mainstream process. Thus, the design approach for recycle water is an important part of any biological nutrient removal system design when a retrofit technology is required for upgrading an existing plant. Moreover, the application of nitrogen removal from recycle water using the nitritation process has recently increased due to economic reasons associated with an effective carbon allocation as well as the minimization of aeration costs. However, for the actual application of recycle water nitritation, it has not been fully examined whether or not additional volume would be required in an existing plant. In this paper, the addition of recycle water nitritation to an existing plant was evaluated based on a volume analysis and estimation of final effluent quality. It was expected that using the reserve volume of the aeration tank in existing plants, recycle water nitritation could be applied to a plant without any enlargement. With the addition of recycle water nitritation, it was estimated that the final effluent quality would be improved and stabilized, especially in the winter season.

Continuous and pulsed laser high power beam combiner for additive manufacturing applications

NASA Astrophysics Data System (ADS)

Bassignana, Marta; Califano, Alessio; Pescarmona, Francesco; Braglia, Andrea; Perrone, Guido

2018-02-01

Laser-based additive manufacturing (AM) from metal powders is emerging as the new industrial revolution, although current fabrication approaches still require long mechanical post-processing to improve the final surface quality and meet the design tolerances. To overcome this limitation, the next generation machines are expected to complement laser AM with laser ablation (LA) to implement surface finishing and micro texturing already during the device growth process. With this aim, a new beam combiner to allow the real-time interchange of additive and subtractive processes using the same scanner head has been designed. Extensive tests have been carried out using a 6 kW continuous-wave laser similar to that used for the metal powder fusion and a nanosecond 100W pulsed source similar to that used for laser ablation.

Three Dimensional Projection Environment for Molecular Design and Surgical Simulation

DTIC Science & Technology

2011-08-01

bypasses the cumbersome meshing process . The deformation model is only comprised of mass nodes, which are generated by sampling the object volume before...force should minimize the penetration volume, the haptic feedback force is derived directly. Additionally, a post- processing technique is developed to...render distinct physi-cal tissue properties across different interaction areas. The proposed approach does not require any pre- processing and is

The Berry Amendment: A Comprehensive Look at the History and Implications for Program Managers of Hand- and Measuring-Tool-Intensive Programs

DTIC Science & Technology

2014-09-01

2. Reciprocal use of DNADs ..................................................................30 E. BERRY AMENDMENT PROCESSES ...the contracting process or procuring of systems that do not totally meet the system requirements provided by the combat developer. From a government...as constraints, restrictions and exceptions provided by the Berry Amendment. Additionally, data will be collected on acquisition processes from

Requirements Development Issues for Advanced Life Support Systems: Solid Waste Management

NASA Technical Reports Server (NTRS)

Levri, Julie A.; Fisher, John W.; Alazraki, Michael P.; Hogan, John A.

2002-01-01

Long duration missions pose substantial new challenges for solid waste management in Advanced Life Support (ALS) systems. These possibly include storing large volumes of waste material in a safe manner, rendering wastes stable or sterilized for extended periods of time, and/or processing wastes for recovery of vital resources. This is further complicated because future missions remain ill-defined with respect to waste stream quantity, composition and generation schedule. Without definitive knowledge of this information, development of requirements is hampered. Additionally, even if waste streams were well characterized, other operational and processing needs require clarification (e.g. resource recovery requirements, planetary protection constraints). Therefore, the development of solid waste management (SWM) subsystem requirements for long duration space missions is an inherently uncertain, complex and iterative process. The intent of this paper is to address some of the difficulties in writing requirements for missions that are not completely defined. This paper discusses an approach and motivation for ALS SWM requirements development, the characteristics of effective requirements, and the presence of those characteristics in requirements that are developed for uncertain missions. Associated drivers for life support system technological capability are also presented. A general means of requirements forecasting is discussed, including successive modification of requirements and the need to consider requirements integration among subsystems.

78 FR 53181 - Self-Regulatory Organizations; New York Stock Exchange LLC; Order Approving Proposed Rule Change...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-28

... process of upgrading their accounting systems and internal controls and hiring additional staff to meet... thereunder, that require registered companies to devise and maintain a system of internal accounting controls... company's risk management processes and system of internal control. A listed company may choose to...

75 FR 62567 - Notice of Lodging of Consent Decree Under the Clean Air Act

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-12

...) and the Chemical Accident Prevention Provisions promulgated at 40 CFR part 68. The United States' CAA... also requires BP Products to regularly report to EPA on indicators of process safety at the Texas City... received process safety training, and (3) whether additional accidental releases of regulated substances...

48 CFR 1352.237-71 - Security processing requirements-low risk contracts.

Code of Federal Regulations, 2012 CFR

2012-10-01

... processed. The Sponsor will forward a completed Form OFI-86C, FD-258, Fingerprint Chart, and Credit Release... (DCII), FBI Fingerprint (FBIF), and the FBI Information Management Division (FBIN). (5) In addition, for.... Fingerprints and a Credit Release Authorization must be completed within three working days from start of work...

48 CFR 1352.237-71 - Security processing requirements-low risk contracts.

Code of Federal Regulations, 2014 CFR

2014-10-01

... processed. The Sponsor will forward a completed Form OFI-86C, FD-258, Fingerprint Chart, and Credit Release... (DCII), FBI Fingerprint (FBIF), and the FBI Information Management Division (FBIN). (5) In addition, for.... Fingerprints and a Credit Release Authorization must be completed within three working days from start of work...

48 CFR 1352.237-71 - Security processing requirements-low risk contracts.

Code of Federal Regulations, 2011 CFR

2011-10-01

... processed. The Sponsor will forward a completed Form OFI-86C, FD-258, Fingerprint Chart, and Credit Release... (DCII), FBI Fingerprint (FBIF), and the FBI Information Management Division (FBIN). (5) In addition, for.... Fingerprints and a Credit Release Authorization must be completed within three working days from start of work...

48 CFR 1352.237-71 - Security processing requirements-low risk contracts.

Code of Federal Regulations, 2010 CFR

2010-10-01

... processed. The Sponsor will forward a completed Form OFI-86C, FD-258, Fingerprint Chart, and Credit Release... (DCII), FBI Fingerprint (FBIF), and the FBI Information Management Division (FBIN). (5) In addition, for.... Fingerprints and a Credit Release Authorization must be completed within three working days from start of work...

48 CFR 1352.237-71 - Security processing requirements-low risk contracts.

Code of Federal Regulations, 2013 CFR

2013-10-01

... processed. The Sponsor will forward a completed Form OFI-86C, FD-258, Fingerprint Chart, and Credit Release... (DCII), FBI Fingerprint (FBIF), and the FBI Information Management Division (FBIN). (5) In addition, for.... Fingerprints and a Credit Release Authorization must be completed within three working days from start of work...

A novel patterning control strategy based on real-time fingerprint recognition and adaptive wafer level scanner optimization

NASA Astrophysics Data System (ADS)

Cekli, Hakki Ergun; Nije, Jelle; Ypma, Alexander; Bastani, Vahid; Sonntag, Dag; Niesing, Henk; Zhang, Linmiao; Ullah, Zakir; Subramony, Venky; Somasundaram, Ravin; Susanto, William; Matsunobu, Masazumi; Johnson, Jeff; Tabery, Cyrus; Lin, Chenxi; Zou, Yi

2018-03-01

In addition to lithography process and equipment induced variations, processes like etching, annealing, film deposition and planarization exhibit variations, each having their own intrinsic characteristics and leaving an effect, a `fingerprint', on the wafers. With ever tighter requirements for CD and overlay, controlling these process induced variations is both increasingly important and increasingly challenging in advanced integrated circuit (IC) manufacturing. For example, the on-product overlay (OPO) requirement for future nodes is approaching <3nm, requiring the allowable budget for process induced variance to become extremely small. Process variance control is seen as an bottleneck to further shrink which drives the need for more sophisticated process control strategies. In this context we developed a novel `computational process control strategy' which provides the capability of proactive control of each individual wafer with aim to maximize the yield, without introducing a significant impact on metrology requirements, cycle time or productivity. The complexity of the wafer process is approached by characterizing the full wafer stack building a fingerprint library containing key patterning performance parameters like Overlay, Focus, etc. Historical wafer metrology is decomposed into dominant fingerprints using Principal Component Analysis. By associating observed fingerprints with their origin e.g. process steps, tools and variables, we can give an inline assessment of the strength and origin of the fingerprints on every wafer. Once the fingerprint library is established, a wafer specific fingerprint correction recipes can be determined based on its processing history. Data science techniques are used in real-time to ensure that the library is adaptive. To realize this concept, ASML TWINSCAN scanners play a vital role with their on-board full wafer detection and exposure correction capabilities. High density metrology data is created by the scanner for each wafer and on every layer during the lithography steps. This metrology data will be used to obtain the process fingerprints. Also, the per exposure and per wafer correction potential of the scanners will be utilized for improved patterning control. Additionally, the fingerprint library will provide early detection of excursions for inline root cause analysis and process optimization guidance.

One-Step Sub-micrometer-Scale Electrohydrodynamic Inkjet Three-Dimensional Printing Technique with Spontaneous Nanoscale Joule Heating.

PubMed

Zhang, Bin; Seong, Baekhoon; Lee, Jaehyun; Nguyen, VuDat; Cho, Daehyun; Byun, Doyoung

2017-09-06

A one-step sub-micrometer-scale electrohydrodynamic (EHD) inkjet three-dimensional (3D)-printing technique that is based on the drop-on-demand (DOD) operation for which an additional postsintering process is not required is proposed. Both the numerical simulation and the experimental observations proved that nanoscale Joule heating occurs at the interface between the charged silver nanoparticles (Ag-NPs) because of the high electrical contact resistance during the printing process; this is the reason why an additional postsintering process is not required. Sub-micrometer-scale 3D structures were printed with an above-35 aspect ratio via the use of the proposed printing technique; furthermore, it is evident that the designed 3D structures such as a bridge-like shape can be printed with the use of the proposed printing technique, allowing for the cost-effective fabrication of a 3D touch sensor and an ultrasensitive air flow-rate sensor. It is believed that the proposed one-step printing technique may replace the conventional 3D conductive-structure printing techniques for which a postsintering process is used because of its economic efficiency.

The regulatory mechanism of fruit ripening revealed by analyses of direct targets of the tomato MADS-box transcription factor RIPENING INHIBITOR

PubMed Central

Fujisawa, Masaki; Ito, Yasuhiro

2013-01-01

The developmental process of ripening is unique to fleshy fruits and a key factor in fruit quality. The tomato (Solanum lycopersicum) MADS-box transcription factor RIPENING INHIBITOR (RIN), one of the earliest-acting ripening regulators, is required for broad aspects of ripening, including ethylene-dependent and -independent pathways. However, our knowledge of direct RIN target genes has been limited, considering the broad effects of RIN on ripening. In a recent work published in The Plant Cell, we identified 241 direct RIN target genes by chromatin immunoprecipitation coupled with DNA microarray (ChIP-chip) and transcriptome analysis. Functional classification of the targets revealed that RIN participates in the regulation of many biological processes including well-known ripening processes such as climacteric ethylene production and lycopene accumulation. In addition, we found that ethylene is required for the full expression of RIN and several RIN-targeting transcription factor genes at the ripening stage. Here, based on our recently published findings and additional data, we discuss the ripening processes regulated by RIN and the interplay between RIN and ethylene. PMID:23518588

Technology's Impact on Graduate Level Reading: Using Technology to Improve Student Assignment Completion Rates

ERIC Educational Resources Information Center

Diamantes, Thomas

2007-01-01

This paper discusses the critical relation between professor, student and technology in the process of encouraging graduate students to read required textbook sections. It discusses how using online management software, graduate students are required to submit weekly chapter summaries to the professor by 5:00 pm on Fridays. In addition to the…

Additive Manufacturing Design Considerations for Liquid Engine Components

NASA Technical Reports Server (NTRS)

Whitten, Dave; Hissam, Andy; Baker, Kevin; Rice, Darron

2014-01-01

The Marshall Space Flight Center's Propulsion Systems Department has gained significant experience in the last year designing, building, and testing liquid engine components using additive manufacturing. The department has developed valve, duct, turbo-machinery, and combustion device components using this technology. Many valuable lessons were learned during this process. These lessons will be the focus of this presentation. We will present criteria for selecting part candidates for additive manufacturing. Some part characteristics are 'tailor made' for this process. Selecting the right parts for the process is the first step to maximizing productivity gains. We will also present specific lessons we learned about feature geometry that can and cannot be produced using additive manufacturing machines. Most liquid engine components were made using a two-step process. The base part was made using additive manufacturing and then traditional machining processes were used to produce the final part. The presentation will describe design accommodations needed to make the base part and lessons we learned about which features could be built directly and which require the final machine process. Tolerance capabilities, surface finish, and material thickness allowances will also be covered. Additive Manufacturing can produce internal passages that cannot be made using traditional approaches. It can also eliminate a significant amount of manpower by reducing part count and leveraging model-based design and analysis techniques. Information will be shared about performance enhancements and design efficiencies we experienced for certain categories of engine parts.

The development and application of a multi-criteria optimization method to the design of a 20-seat regional jet airliner

NASA Astrophysics Data System (ADS)

Au, How Meng

The aircraft design process traditionally starts with a given set of top-level requirements. These requirements can be aircraft performance related such as the fuel consumption, cruise speed, or takeoff field length, etc., or aircraft geometry related such as the cabin height or cabin volume, etc. This thesis proposes a new aircraft design process in which some of the top-level requirements are not explicitly specified. Instead, these previously specified parameters are now determined through the use of the Price-Per-Value-Factor (PPVF) index. This design process is well suited for design projects where general consensus of the top-level requirements does not exist. One example is the design of small commuter airliners. The above mentioned value factor is comprised of productivity, cabin volume, cabin height, cabin pressurization, mission fuel consumption, and field length, each weighted to a different exponent. The relative magnitude and positive/negative signs of these exponents are in agreement with general experience. The value factors of the commuter aircraft are shown to have improved over a period of four decades. In addition, the purchase price is shown to vary linearly with the value factor. The initial aircraft sizing process can be manpower intensive if the calculations are done manually. By incorporating automation into the process, the design cycle can be shortened considerably. The Fortran program functions and subroutines in this dissertation, in addition to the design and optimization methodologies described above, contribute to the reduction of manpower required for the initial sizing process. By combining the new design process mentioned above and the PPVF as the objective function, an optimization study is conducted on the design of a 20-seat regional jet. Handbook methods for aircraft design are written into a Fortran code. A genetic algorithm is used as the optimization scheme. The result of the optimization shows that aircraft designed to this PPVF index can be competitive compared to existing turboprop commuter aircraft. The process developed can be applied to other classes of aircraft with the designer modifying the cost function based upon the design goals.

Caregiver involvement in a large clinical systems project.

PubMed Central

Sales, S.; Mathews, P.; Gamblin, D.; Gee, S.

1994-01-01

The Kaiser Permanente Northern California Region (KPNCR) CareGiver Workstation (CGW) Project's mission is to develop and implement a clinical workstation system that will enhance each caregiver-member interaction and aid in the decision-making processes of direct patient care in the inpatient and outpatient settings. The requirements analysis approach for CareGiver Workstation (CGW) is based on the belief that extensive caregiver involvement will provide a better understanding of the diverse needs of Kaiser Permanente Northern California Region (KPNCR). In order to involve as many caregivers as reasonably possible, CGW included a 16 member caregiver core team and 6 different Medical Centers in the requirements definition process. The Medical Centers are referred to as "focus facilities". A "focus group" (caregiver team) at each selected focus facility consisted of a site coordinator and a 24-30 person multidisciplinary team involving physicians, nurses, therapists and other caregivers. The Medical Center selection process identified facilities that provided the best cross-sectional representation of KPNCR. The Lead Focus Facility participated in the initial round of requirements definition activities. These sessions assisted in the design of a simulation that was used at five additional Medical Centers to validate requirements. The five additional Focus Facilities participated in simulation review sessions. Feedback from these sessions was used to revise the simulation and update the requirements document. Caregivers from all six focus facilities and other identified groups participated in a requirements survey to assist CGW with identification of high priority features. Caregiver commitment and continuing involvement are essential for the success of CGW.(ABSTRACT TRUNCATED AT 250 WORDS) PMID:7949953

41 CFR 109-27.5011-1 - General.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., or for use on construction projects. Additional markings not covered by Federal standards should be used to show special properties, corrosion data, or test data as required. The preferred process is for...

Mathematical Analysis of High-Temperature Co-electrolysis of CO2 and O2 Production in a Closed-Loop Atmosphere Revitalization System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Michael G. McKellar; Manohar S. Sohal; Lila Mulloth

2010-03-01

NASA has been evaluating two closed-loop atmosphere revitalization architectures based on Sabatier and Bosch carbon dioxide, CO2, reduction technologies. The CO2 and steam, H2O, co-electrolysis process is another option that NASA has investigated. Utilizing recent advances in the fuel cell technology sector, the Idaho National Laboratory, INL, has developed a CO2 and H2O co-electrolysis process to produce oxygen and syngas (carbon monoxide, CO and hydrogen, H2 mixture) for terrestrial (energy production) application. The technology is a combined process that involves steam electrolysis, CO2 electrolysis, and the reverse water gas shift (RWGS) reaction. A number of process models have been developedmore » and analyzed to determine the theoretical power required to recover oxygen, O2, in each case. These models include the current Sabatier and Bosch technologies and combinations of those processes with high-temperature co-electrolysis. The cases of constant CO2 supply and constant O2 production were evaluated. In addition, a process model of the hydrogenation process with co-electrolysis was developed and compared. Sabatier processes require the least amount of energy input per kg of oxygen produced. If co-electrolysis replaces solid polymer electrolyte (SPE) electrolysis within the Sabatier architecture, the power requirement is reduced by over 10%, but only if heat recuperation is used. Sabatier processes, however, require external water to achieve the lower power results. Under conditions of constant incoming carbon dioxide flow, the Sabatier architectures require more power than the other architectures. The Bosch, Boudouard with co-electrolysis, and the hydrogenation with co-electrolysis processes require little or no external water. The Bosch and hydrogenation processes produce water within their reactors, which aids in reducing the power requirement for electrolysis. The Boudouard with co-electrolysis process has a higher electrolysis power requirement because carbon dioxide is split instead of water, which has a lower heat of formation. Hydrogenation with co-electrolysis offers the best overall power performance for two reasons: it requires no external water, and it produces its own water, which reduces the power requirement for co-electrolysis.« less

Inertial Energy Storage for Spacecraft

NASA Technical Reports Server (NTRS)

Rodriguez, G. E.

1984-01-01

The feasibility of inertial energy storage in a spacecraft power system is evaluated on the basis of a conceptual integrated design that encompasses a composite rotor, magnetic suspension and a permanent magnet (PM) motor/generator for a 3-kW orbital average payload at a bus distribution voltage of 250 volts dc. The conceptual design, is referred to as a Mechanical Capacitor. The baseline power system configuration selected is a series system employing peak-power-tracking for a Low Earth-Orbiting application. Power processing, required in the motor/generator, provides potential alternative that can only be achieved in systems with electrochemical energy storage by the addition of power processing components. One such alternative configuration provides for peak-power-tracking of the solar array and still maintains a regulated bus, without the expense of additional power processing components. Precise speed control of the two counterrotating wheels is required to reduce interaction with the attitude control system (ACS) or alternatively, used to perform attitude control functions.

Processing of high performance (LRE)-Ba Cu O large, single-grain bulk superconductors in air

NASA Astrophysics Data System (ADS)

Hari Babu, N.; Iida, K.; Shi, Y.; Cardwell, D. A.

2006-10-01

We report the fabrication of large (LRE)BCO single-grains with improved superconducting properties for LRE = Nd, Sm and Gd using a practical process via both conventional top seeded melt growth (TSMG) and seeded infiltration-growth (SIG). This process uses a new generic seed crystal that promotes heterogeneous grain nucleation in the required orientation and suppresses the formation of solid solution in a controlled manner within individual grains by the addition of excess BaO2 to the precursor powder. The spatial distribution of the superconducting properties of LRE bulk superconductors as a function of BaO2 addition for large (LRE)BCO grains fabricated in air by TSMG and SIG for LRE = Gd, Sm and Nd are compared. The optimum BaO2 content required to fabricate single-grain (LRE)BCO with high and homogeneous Tc is determined from these experiments for each LRE system. The irreversibility fields of (LRE)BCO bulk superconductors processed in air are as high as those processed in reduced PO2. Critical current densities in excess of 105 A/cm2 at 77 K and higher trapped fields have been achieved in optimized (LRE)BCO superconductors fabricated in air for the first time.

Plans for Assessing Contractor Performance for the Camp Lemonnier Base Operations Support Contract Needed Improvement

DTIC Science & Technology

2015-08-27

ensure the functional assessment plans ( FAP ) for the three services contained all contractor work requiring assessment, measurable performance...review the FAPs after development and revisions to the FAPs , and did not require additional controls over the contractor assessment process in an...revised as follows: • Business Management System B-14.3 was updated to require the contract officer representative conduct a FAP review to ensure

Use of soybean oil and ammonium sulfate additions to optimize secondary metabolite production.

PubMed

Junker, B; Mann, Z; Gailliot, P; Byrne, K; Wilson, J

1998-12-05

A valine-overproducing mutant (MA7040, Streptomyces hygroscopicus) was found to produce 1.5 to 2.0 g/L of the immunoregulant, L-683,590, at the 0.6 m3 fermentation scale in a simple batch process using soybean oil and ammonium sulfate-based GYG5 medium. Levels of both lower (L-683,795) and higher (HH1 and HH2) undesirable homolog levels were controlled adequately. This batch process was utilized to produce broth economically at the 19 m3 fermentation scale. Material of acceptable purity was obtained without the multiple pure crystallizations previously required for an earlier culture, MA6678, requiring valine supplementation for impurity control. Investigations at the 0.6 m3 fermentation scale were conducted, varying agitation, pH, initial soybean oil/ammonium sulfate charges, and initial aeration rate to further improve growth and productivity. Mid-cycle ammonia levels and lipase activity appeared to have an important role. Using mid-cycle soybean oil additions, a titer of 2.3 g/L of L-683,590 was obtained, while titers reached 2.7 g/L using mid-cycle soybean oil and ammonium sulfate additions. Both higher and lower homolog levels remained acceptable during this fed-batch process. Optimal timing of mid-cycle oil and ammonium sulfate additions was considered a critical factor to further titer improvements. Copyright 1998 John Wiley & Sons, Inc.

A Model of Batch Scheduling for a Single Batch Processor with Additional Setups to Minimize Total Inventory Holding Cost of Parts of a Single Item Requested at Multi-due-date

NASA Astrophysics Data System (ADS)

Hakim Halim, Abdul; Ernawati; Hidayat, Nita P. A.

2018-03-01

This paper deals with a model of batch scheduling for a single batch processor on which a number of parts of a single items are to be processed. The process needs two kinds of setups, i. e., main setups required before processing any batches, and additional setups required repeatedly after the batch processor completes a certain number of batches. The parts to be processed arrive at the shop floor at the times coinciding with their respective starting times of processing, and the completed parts are to be delivered at multiple due dates. The objective adopted for the model is that of minimizing total inventory holding cost consisting of holding cost per unit time for a part in completed batches, and that in in-process batches. The formulation of total inventory holding cost is derived from the so-called actual flow time defined as the interval between arrival times of parts at the production line and delivery times of the completed parts. The actual flow time satisfies not only minimum inventory but also arrival and delivery just in times. An algorithm to solve the model is proposed and a numerical example is shown.

Bitumen and heavy oil upgrading in Canada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chrones, J.; Germain, R.R.

1989-01-01

A review is presented of the heavy oil upgrading industry in Canada. Up to now it has been based on the processing of bitumen extracted from oil sands mining operations at two sites, to produce a residue-free, low sulphur, synthetic crude. Carbon rejection has been the prime process technology with delayed coking being used by Suncor and FLUID COKING at Syncrude. Alternative processes for recovering greater amounts of synthetic crude are examined. These include a variety of hydrogen addition processes and combinations which produce pipelineable materials requiring further processing in downstream refineries with expanded capabilities. The Newgrade Energy Inc. upgradermore » now under construction in Regina, will use fixed-bed, catalytic, atmospheric-residue, hydrogen processing. Two additional projects, also based on hydrogenation, will use ebullated bed catalyst systems; the expansion of Syncrude, now underway, is using the LC Fining Process whereas the announced Husky Bi-Provincial upgrader is based on H-Oil.« less

Bitumen and heavy oil upgrading in Canada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chrones, J.

1988-06-01

A review is presented of the heavy oil upgrading industry in Canada. Up to now it has been based on the processing of bitumen extracted from oil sands mining operations at two sites, to produce a residue-free, low sulfur, synthetic crude. Carbon rejection has been the prime process technology with delayed coking being used by Suncor and FLUID COKING at Syncrude. Alternative processes for recovering greater amounts of synthetic crude are examined. These include a variety of hydrogen addition processes and combinations which produce pipelineable materials requiring further processing in downstream refineries with expanded capabilities. The Newgrade Energy Inc. upgrader,more » now under construction in Regina, will use fixed-bed, catalytic, atmospheric-residue, hydrogen processing. Two additional products, also based on hydrogenation, will use ebullated bed catalyst systems: the expansion of Syncrude, now underway, is using the LC Fining Process whereas the announced Husky Bi-Provincial upgrader is based on H-Oil.« less

Development and qualification of additively manufactured parts for space

NASA Astrophysics Data System (ADS)

O'Brien, Michael J.

2018-02-01

Additive manufacturing (commonly called "3D printing") fabricates the desired final part directly from the input CAD (Computer Aided Design) file by depositing and fusing layer upon layer of the source material. New engineering designs are possible in which a single optimized part with novel topology can replace several traditional parts. The complex physics of metal deposition leads to variations in quality and to new flaws and residual stresses not seen in traditional manufacturing. Additive manufacturing currently has gaps in knowledge. Mission assurance will require: qualification and certification standards; sharing of data in handbooks; predictive models relating processing, microstructure and properties; and development of closed loop process control and non-destructive evaluation to reduce variability.

3D freeform printing of silk fibroin.

PubMed

Rodriguez, Maria J; Dixon, Thomas A; Cohen, Eliad; Huang, Wenwen; Omenetto, Fiorenzo G; Kaplan, David L

2018-04-15

Freeform fabrication has emerged as a key direction in printing biologically-relevant materials and structures. With this emerging technology, complex structures with microscale resolution can be created in arbitrary geometries and without the limitations found in traditional bottom-up or top-down additive manufacturing methods. Recent advances in freeform printing have used the physical properties of microparticle-based granular gels as a medium for the submerged extrusion of bioinks. However, most of these techniques require post-processing or crosslinking for the removal of the printed structures (Miller et al., 2015; Jin et al., 2016) [1,2]. In this communication, we introduce a novel method for the one-step gelation of silk fibroin within a suspension of synthetic nanoclay (Laponite) and polyethylene glycol (PEG). Silk fibroin has been used as a biopolymer for bioprinting in several contexts, but chemical or enzymatic additives or bulking agents are needed to stabilize 3D structures. Our method requires no post-processing of printed structures and allows for in situ physical crosslinking of pure aqueous silk fibroin into arbitrary geometries produced through freeform 3D printing. 3D bioprinting has emerged as a technology that can produce biologically relevant structures in defined geometries with microscale resolution. Techniques for fabrication of free-standing structures by printing into granular gel media has been demonstrated previously, however, these methods require crosslinking agents and post-processing steps on printed structures. Our method utilizes one-step gelation of silk fibroin within a suspension of synthetic nanoclay (Laponite), with no need for additional crosslinking compounds or post processing of the material. This new method allows for in situ physical crosslinking of pure aqueous silk fibroin into defined geometries produced through freeform 3D printing. Copyright © 2018 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Automatic pattern localization across layout database and photolithography mask

NASA Astrophysics Data System (ADS)

Morey, Philippe; Brault, Frederic; Beisser, Eric; Ache, Oliver; Röth, Klaus-Dieter

2016-03-01

Advanced process photolithography masks require more and more controls for registration versus design and critical dimension uniformity (CDU). The distribution of the measurement points should be distributed all over the whole mask and may be denser in areas critical to wafer overlay requirements. This means that some, if not many, of theses controls should be made inside the customer die and may use non-dedicated patterns. It is then mandatory to access the original layout database to select patterns for the metrology process. Finding hundreds of relevant patterns in a database containing billions of polygons may be possible, but in addition, it is mandatory to create the complete metrology job fast and reliable. Combining, on one hand, a software expertise in mask databases processing and, on the other hand, advanced skills in control and registration equipment, we have developed a Mask Dataprep Station able to select an appropriate number of measurement targets and their positions in a huge database and automatically create measurement jobs on the corresponding area on the mask for the registration metrology system. In addition, the required design clips are generated from the database in order to perform the rendering procedure on the metrology system. This new methodology has been validated on real production line for the most advanced process. This paper presents the main challenges that we have faced, as well as some results on the global performances.

Real-Time Processing of ASL Signs: Delayed First Language Acquisition Affects Organization of the Mental Lexicon

ERIC Educational Resources Information Center

Lieberman, Amy M.; Borovsky, Arielle; Hatrak, Marla; Mayberry, Rachel I.

2015-01-01

Sign language comprehension requires visual attention to the linguistic signal and visual attention to referents in the surrounding world, whereas these processes are divided between the auditory and visual modalities for spoken language comprehension. Additionally, the age-onset of first language acquisition and the quality and quantity of…

State Standard-Setting Processes in Brief. State Academic Standards: Standard-Setting Processes

ERIC Educational Resources Information Center

Thomsen, Jennifer

2014-01-01

Concerns about academic standards, whether created by states from scratch or adopted by states under the Common Core State Standards (CCSS) banner, have drawn widespread media attention and are at the top of many state policymakers' priority lists. Recently, a number of legislatures have required additional steps, such as waiting periods for…

78 FR 47691 - UGI, Inc.; Notice of Intent to Prepare an Environmental Assessment for the Proposed Temple LNG...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-06

..., Pennsylvania. This EA will be used by the Commission in its decision-making process to determine whether the... ``Additional Information'' section at the end of this notice. Land Requirements for Construction UGI plans to... (NEPA) requires the Commission to take into account the environmental impacts that could result from an...

Natural Attenuation of Perchlorate in Groundwater: Processes, Tools and Monitoring Techniques

DTIC Science & Technology

2008-04-01

attenuation of perchlorate. Tier 3: Microbiological Indicators. For situations where additional lines of evidence are required, Tier 3 offers...USEPA, 1997). Like enhanced bioremediation, MNA requires an in-depth understanding of the microbiology , chemistry, and hydrogeology of the...nitrate, perchlorate (if present), and iron have been depleted in the microbiological treatment zone. Whereas sulfate concentration greater than 20

Unified Modeling Language (UML) for hospital-based cancer registration processes.

PubMed

Shiki, Naomi; Ohno, Yuko; Fujii, Ayumi; Murata, Taizo; Matsumura, Yasushi

2008-01-01

Hospital-based cancer registry involves complex processing steps that span across multiple departments. In addition, management techniques and registration procedures differ depending on each medical facility. Establishing processes for hospital-based cancer registry requires clarifying specific functions and labor needed. In recent years, the business modeling technique, in which management evaluation is done by clearly spelling out processes and functions, has been applied to business process analysis. However, there are few analytical reports describing the applications of these concepts to medical-related work. In this study, we initially sought to model hospital-based cancer registration processes using the Unified Modeling Language (UML), to clarify functions. The object of this study was the cancer registry of Osaka University Hospital. We organized the hospital-based cancer registration processes based on interview and observational surveys, and produced an As-Is model using activity, use-case, and class diagrams. After drafting every UML model, it was fed-back to practitioners to check its validity and improved. We were able to define the workflow for each department using activity diagrams. In addition, by using use-case diagrams we were able to classify each department within the hospital as a system, and thereby specify the core processes and staff that were responsible for each department. The class diagrams were effective in systematically organizing the information to be used for hospital-based cancer registries. Using UML modeling, hospital-based cancer registration processes were broadly classified into three separate processes, namely, registration tasks, quality control, and filing data. An additional 14 functions were also extracted. Many tasks take place within the hospital-based cancer registry office, but the process of providing information spans across multiple departments. Moreover, additional tasks were required in comparison to using a standardized system because the hospital-based cancer registration system was constructed with the pre-existing computer system in Osaka University Hospital. Difficulty of utilization of useful information for cancer registration processes was shown to increase the task workload. By using UML, we were able to clarify functions and extract the typical processes for a hospital-based cancer registry. Modeling can provide a basis of process analysis for establishment of efficient hospital-based cancer registration processes in each institute.

17 CFR 38.252 - Additional requirements for physical-delivery contracts.

Code of Federal Regulations, 2013 CFR

2013-04-01

... commodity and show a good-faith effort to resolve conditions that are interfering with convergence; and (b...-faith effort to resolve conditions that threaten the adequacy of supplies or the delivery process. ...

25 CFR 273.18 - Additional requirements for education plan.

Code of Federal Regulations, 2012 CFR

2012-04-01

... EDUCATION ASSISTANCE ACT PROGRAM EDUCATION CONTRACTS UNDER JOHNSON-O'MALLEY ACT Application Process § 273.18... needed to carry out the contract. (o) State the period of contract term requested. (p) Include the...

25 CFR 273.18 - Additional requirements for education plan.

Code of Federal Regulations, 2013 CFR

2013-04-01

... EDUCATION ASSISTANCE ACT PROGRAM EDUCATION CONTRACTS UNDER JOHNSON-O'MALLEY ACT Application Process § 273.18... needed to carry out the contract. (o) State the period of contract term requested. (p) Include the...

25 CFR 273.18 - Additional requirements for education plan.

Code of Federal Regulations, 2014 CFR

2014-04-01

... EDUCATION ASSISTANCE ACT PROGRAM EDUCATION CONTRACTS UNDER JOHNSON-O'MALLEY ACT Application Process § 273.18... needed to carry out the contract. (o) State the period of contract term requested. (p) Include the...

The reactive bed plasma system for contamination control

NASA Technical Reports Server (NTRS)

Birmingham, Joseph G.; Moore, Robert R.; Perry, Tony R.

1990-01-01

The contamination control capabilities of the Reactive Bed Plasma (RBP) system is described by delineating the results of toxic chemical composition studies, aerosol filtration work, and other testing. The RBP system has demonstrated its capabilities to decompose toxic materials and process hazardous aerosols. The post-treatment requirements for the reaction products have possible solutions. Although additional work is required to meet NASA requirements, the RBP may be able to meet contamination control problems aboard the Space Station.

Registration and Marking Requirements for UAS. Unmanned Aircraft System (UAS) Registration

NASA Technical Reports Server (NTRS)

2005-01-01

The registration of an aircraft is a prerequisite for issuance of a U.S. certificate of airworthiness by the FAA. The procedures and requirements for aircraft registration, and the subsequent issuance of registration numbers, are contained in FAR Part 47. However, the process/method(s) for applying the requirements of Parts 45 & 47 to Unmanned Aircraft Systems (UAS) has not been defined. This task resolved the application of 14 CFR Parts 45 and 47 to UAS. Key Findings: UAS are aircraft systems and as such the recommended approach to registration is to follow the same process for registration as manned aircraft. This will require manufacturers to comply with the requirements for 14 CFR 47, Aircraft Registration and 14 CFR 45, Identification and Registration Marking. In addition, only the UA should be identified with the N number registration markings. There should also be a documentation link showing the applicability of the control station and communication link to the UA. The documentation link can be in the form of a Type Certificate Data Sheet (TCDS) entry or a UAS logbook entry. The recommended process for the registration of UAS is similar to the manned aircraft process and is outlined in a 6-step process in the paper.

Higher biodiversity is required to sustain multiple ecosystem processes across temperature regimes

PubMed Central

Perkins, Daniel M; Bailey, R A; Dossena, Matteo; Gamfeldt, Lars; Reiss, Julia; Trimmer, Mark; Woodward, Guy

2015-01-01

Biodiversity loss is occurring rapidly worldwide, yet it is uncertain whether few or many species are required to sustain ecosystem functioning in the face of environmental change. The importance of biodiversity might be enhanced when multiple ecosystem processes (termed multifunctionality) and environmental contexts are considered, yet no studies have quantified this explicitly to date. We measured five key processes and their combined multifunctionality at three temperatures (5, 10 and 15 °C) in freshwater aquaria containing different animal assemblages (1–4 benthic macroinvertebrate species). For single processes, biodiversity effects were weak and were best predicted by additive-based models, i.e. polyculture performances represented the sum of their monoculture parts. There were, however, significant effects of biodiversity on multifunctionality at the low and the high (but not the intermediate) temperature. Variation in the contribution of species to processes across temperatures meant that greater biodiversity was required to sustain multifunctionality across different temperatures than was the case for single processes. This suggests that previous studies might have underestimated the importance of biodiversity in sustaining ecosystem functioning in a changing environment. PMID:25131335

Modeling of Ti-W Solidification Microstructures Under Additive Manufacturing Conditions

NASA Astrophysics Data System (ADS)

Rolchigo, Matthew R.; Mendoza, Michael Y.; Samimi, Peyman; Brice, David A.; Martin, Brian; Collins, Peter C.; LeSar, Richard

2017-07-01

Additive manufacturing (AM) processes have many benefits for the fabrication of alloy parts, including the potential for greater microstructural control and targeted properties than traditional metallurgy processes. To accelerate utilization of this process to produce such parts, an effective computational modeling approach to identify the relationships between material and process parameters, microstructure, and part properties is essential. Development of such a model requires accounting for the many factors in play during this process, including laser absorption, material addition and melting, fluid flow, various modes of heat transport, and solidification. In this paper, we start with a more modest goal, to create a multiscale model for a specific AM process, Laser Engineered Net Shaping (LENS™), which couples a continuum-level description of a simplified beam melting problem (coupling heat absorption, heat transport, and fluid flow) with a Lattice Boltzmann-cellular automata (LB-CA) microscale model of combined fluid flow, solute transport, and solidification. We apply this model to a binary Ti-5.5 wt pct W alloy and compare calculated quantities, such as dendrite arm spacing, with experimental results reported in a companion paper.

Lightning Arrestor Connectors Production Readiness

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marten, Steve; Linder, Kim; Emmons, Jim

2008-10-20

The Lightning Arrestor Connector (LAC), part “M”, presented opportunities to improve the processes used to fabricate LACs. The A## LACs were the first production LACs produced at the KCP, after the product was transferred from Pinnellas. The new LAC relied on the lessons learned from the A## LACs; however, additional improvements were needed to meet the required budget, yield, and schedule requirements. Improvement projects completed since 2001 include Hermetic Connector Sealing Improvement, Contact Assembly molding Improvement, development of a second vendor for LAC shells, general process improvement, tooling improvement, reduction of the LAC production cycle time, and documention of themore » LAC granule fabrication process. This report summarizes the accomplishments achieved in improving the LAC Production Readiness.« less

Additive manufacturing of titanium alloys in the biomedical field: processes, properties and applications.

PubMed

Trevisan, Francesco; Calignano, Flaviana; Aversa, Alberta; Marchese, Giulio; Lombardi, Mariangela; Biamino, Sara; Ugues, Daniele; Manfredi, Diego

2018-04-01

The mechanical properties and biocompatibility of titanium alloy medical devices and implants produced by additive manufacturing (AM) technologies - in particular, selective laser melting (SLM), electron beam melting (EBM) and laser metal deposition (LMD) - have been investigated by several researchers demonstrating how these innovative processes are able to fulfil medical requirements for clinical applications. This work reviews the advantages given by these technologies, which include the possibility to create porous complex structures to improve osseointegration and mechanical properties (best match with the modulus of elasticity of local bone), to lower processing costs, to produce custom-made implants according to the data for the patient acquired via computed tomography and to reduce waste.

Design requirements and development of an airborne descent path definition algorithm for time navigation

NASA Technical Reports Server (NTRS)

Izumi, K. H.; Thompson, J. L.; Groce, J. L.; Schwab, R. W.

1986-01-01

The design requirements for a 4D path definition algorithm are described. These requirements were developed for the NASA ATOPS as an extension of the Local Flow Management/Profile Descent algorithm. They specify the processing flow, functional and data architectures, and system input requirements, and recommended the addition of a broad path revision (reinitialization) function capability. The document also summarizes algorithm design enhancements and the implementation status of the algorithm on an in-house PDP-11/70 computer. Finally, the requirements for the pilot-computer interfaces, the lateral path processor, and guidance and steering function are described.

Advances in multi-scale modeling of solidification and casting processes

NASA Astrophysics Data System (ADS)

Liu, Baicheng; Xu, Qingyan; Jing, Tao; Shen, Houfa; Han, Zhiqiang

2011-04-01

The development of the aviation, energy and automobile industries requires an advanced integrated product/process R&D systems which could optimize the product and the process design as well. Integrated computational materials engineering (ICME) is a promising approach to fulfill this requirement and make the product and process development efficient, economic, and environmentally friendly. Advances in multi-scale modeling of solidification and casting processes, including mathematical models as well as engineering applications are presented in the paper. Dendrite morphology of magnesium and aluminum alloy of solidification process by using phase field and cellular automaton methods, mathematical models of segregation of large steel ingot, and microstructure models of unidirectionally solidified turbine blade casting are studied and discussed. In addition, some engineering case studies, including microstructure simulation of aluminum casting for automobile industry, segregation of large steel ingot for energy industry, and microstructure simulation of unidirectionally solidified turbine blade castings for aviation industry are discussed.

78 FR 12137 - Agency Information Collection Activities: Request for the Renewal of an Information Collection

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-21

... provides an online reporting tool to support the annual HSIP reporting process. Additional information is.../ . Reporting into the online reporting tool meets all report requirements and USDOT Web site compatibility...

Defense Inventory: DOD Needs Additional Information for Managing War Reserve Levels of Meals Ready to Eat

DTIC Science & Technology

2015-05-01

to provide operational ration manufacturers with two types of machines to assist with the cooking and filling and sealing process for operational...and (3) any strategies DLA pursues to balance cost with readiness in supplying WRM. GAO obtained information from the services on their processes ...for identifying WRM requirements, reviewed DLA’s inventory-management processes and related guidance, and interviewed DLA and military service

Ultrasonication aided in-situ transesterification of microbial lipids to biodiesel.

PubMed

Zhang, Xiaolei; Yan, Song; Tyagi, Rajeshwar Dayal; Surampalli, Rao Y; Valéro, Jose R

2014-10-01

In-situ transesterification of microbial lipid to biodiesel has been paid substantial attention due to the fact that the lipid extraction and transesterification can be conducted in one-stage process. To improve the feasibility of in-situ transesterification, ultrasonication was employed to reduce methanol requirement and reaction time. The results showed that the use of ultrasonication could achieve high conversion of lipid to FAMEs (92.1% w lipid conversion/w total lipids) with methanol to lipid molar ratio 60:1 and NaOH addition 1% w/w lipid in 20 min, while methanol to lipid molar ratio 360:1, NaOH addition 1% w/w lipid, and reaction time 12h was required to obtain similar yield in in-situ transesterification without ultrasonication. The compositions of FAMEs obtained in case of ultrasonication aided in-situ transesterification were similar as that of two-stage extraction followed by transesterification processes. Copyright © 2014. Published by Elsevier Ltd.

The Pharmaceutical Capping Process-Correlation between Residual Seal Force, Torque Moment, and Flip-off Removal Force.

PubMed

Mathaes, Roman; Mahler, Hanns-Christian; Vorgrimler, Lothar; Steinberg, Henrik; Dreher, Sascha; Roggo, Yves; Nieto, Alejandra; Brown, Helen; Roehl, Holger; Adler, Michael; Luemkemann, Joerg; Huwyler, Joerg; Lam, Philippe; Stauch, Oliver; Mohl, Silke; Streubel, Alexander

2016-01-01

The majority of parenteral drug products are manufactured in glass vials with an elastomeric rubber stopper and a crimp cap. The vial sealing process is a critical process step during fill-and-finish operations, as it defines the seal quality of the final product. Different critical capping process parameters can affect rubber stopper defects, rubber stopper compression, container closure integrity, and also crimp cap quality. A sufficiently high force to remove the flip-off button prior to usage is required to ensure quality of the drug product unit by the flip-off button during storage, transportation, and until opening and use. Therefore, the final product is 100% visually inspected for lose or defective crimp caps, which is subjective as well as time- and labor-intensive. In this study, we sealed several container closure system configurations with different capping equipment settings (with corresponding residual seal force values) to investigate the torque moment required to turn the crimp cap. A correlation between torque moment and residual seal force has been established. The torque moment was found to be influenced by several parameters, including diameter of the vial head, type of rubber stopper (serum or lyophilized) and type of crimp cap (West(®) or Datwyler(®)). In addition, we measured the force required to remove the flip-off button of a sealed container closure system. The capping process had no influence on measured forces; however, it was possible to detect partially crimped vials. In conclusion, a controlled capping process with a defined target residual seal force range leads to a tight crimp cap on a sealed container closure system and can ensure product quality. The majority of parenteral drug products are manufactured in a glass vials with an elastomeric rubber stopper and a crimp cap. The vial sealing process is a critical process step during fill-and-finish operations, as it defines the seal quality of the final product. An adequate force to remove the flip-off button prior to usage is required to ensure product quality during storage and transportation until use. In addition, the complete crimp cap needs to be fixed in a tight position on the vial. In this study, we investigated the torque moment required to turn the crimp cap and the force required to remove the flip-off button of container closure system sealed with different capping equipment process parameters (having different residual seal force values). © PDA, Inc. 2016.

Grain Structure Control of Additively Manufactured Metallic Materials

PubMed Central

Faierson, Eric J.

2017-01-01

Grain structure control is challenging for metal additive manufacturing (AM). Grain structure optimization requires the control of grain morphology with grain size refinement, which can improve the mechanical properties of additive manufactured components. This work summarizes methods to promote fine equiaxed grains in both the additive manufacturing process and subsequent heat treatment. Influences of temperature gradient, solidification velocity and alloy composition on grain morphology are discussed. Equiaxed solidification is greatly promoted by introducing a high density of heterogeneous nucleation sites via powder rate control in the direct energy deposition (DED) technique or powder surface treatment for powder-bed techniques. Grain growth/coarsening during post-processing heat treatment can be restricted by presence of nano-scale oxide particles formed in-situ during AM. Grain refinement of martensitic steels can also be achieved by cyclic austenitizing in post-processing heat treatment. Evidently, new alloy powder design is another sustainable method enhancing the capability of AM for high-performance components with desirable microstructures.

Granular starch hydrolysis for fuel ethanol production

NASA Astrophysics Data System (ADS)

Wang, Ping

Granular starch hydrolyzing enzymes (GSHE) convert starch into fermentable sugars at low temperatures (≤48°C). Use of GSHE in dry grind process can eliminate high temperature requirements during cooking and liquefaction (≥90°C). In this study, GSHE was compared with two combinations of commercial alpha-amylase and glucoamylase (DG1 and DG2, respectively). All three enzyme treatments resulted in comparable ethanol concentrations (between 14.1 to 14.2% v/v at 72 hr), ethanol conversion efficiencies and ethanol and DDGS yields. Sugar profiles for the GSHE treatment were different from DG1 and DG2 treatments, especially for glucose. During simultaneous saccharification and fermentation (SSF), the highest glucose concentration for the GSHE treatment was 7% (w/v); for DG1 and DG2 treatments, maximum glucose concentration was 19% (w/v). GSHE was used in one of the fractionation technologies (enzymatic dry grind) to improve recovery of germ and pericarp fiber prior to fermentation. The enzymatic dry grind process with GSHE was compared with the conventional dry grind process using GSHE with the same process parameters of dry solids content, pH, temperature, time, enzyme and yeast usages. Ethanol concentration (at 72 hr) of the enzymatic process was 15.5% (v/v), which was 9.2% higher than the conventional process (14.2% v/v). Distillers dried grains with solubles (DDGS) generated from the enzymatic process (9.8% db) was 66% less than conventional process (28.3% db). Three additional coproducts, germ 8.0% (db), pericarp fiber 7.7% (db) and endosperm fiber 5.2% (db) were produced. Costs and amounts of GSHE used is an important factor affecting dry grind process economics. Proteases can weaken protein matrix to aid starch release and may reduce GSHE doses. Proteases also can hydrolyze protein into free amino nitrogen (FAN), which can be used as a yeast nutrient during fermentation. Two types of proteases, exoprotease and endoprotease, were studied; protease and urea addition were evaluated in the dry grind process using GSHE (GSH process). Addition of proteases resulted in higher ethanol concentrations (15.2 to 18.0% v/v) and lower (DDGS) yields (32.9 to 45.8% db) compared to the control (no protease addition). As level of proteases and GSHE increased, ethanol concentrations increased and DDGS yields decreased. Proteases addition reduced required GSHE dose. Ethanol concentrations with protease addition alone were higher than with urea or with addition of both protease and urea. Corn endosperm consists of soft and hard endosperm. More exposed starch granules and rough surfaces produced from soft endosperm compared to hard endosperm will create more surface area which will benefit the solid phase hydrolysis as used in GSH process. In this study, the effects of protease, urea, endosperm hardness and GSHE levels on the GSH process were evaluated. Soft and hard endosperm materials were obtained by grinding and sifting flaking grits from dry milling pilot plant. Soft endosperm resulted in higher ethanol concentrations (at 72 hr) compared to ground corn or hard endosperm. Addition of urea increased ethanol concentrations (at 72 hr) for soft and hard endosperm. The effect of protease addition on increasing ethanol concentrations and fermentation rates was more predominant for soft endosperm, less for hard endosperm and least for ground corn. The GSH process with protease resulted in higher ethanol concentration than that with urea. For fermentation of soft endosperm, GSHE dose can be reduced. Ground corn fermented faster at the beginning than hard and soft endosperm due to the presence of inherent nutrients which enhanced yeast growth.

Experimental comparison of residual stresses for a thermomechanical model for the simulation of selective laser melting

DOE PAGES

Hodge, N. E.; Ferencz, R. M.; Vignes, R. M.

2016-05-30

Selective laser melting (SLM) is an additive manufacturing process in which multiple, successive layers of metal powders are heated via laser in order to build a part. Modeling of SLM requires consideration of the complex interaction between heat transfer and solid mechanics. Here, the present work describes the authors initial efforts to validate their first generation model. In particular, the comparison of model-generated solid mechanics results, including both deformation and stresses, is presented. Additionally, results of various perturbations of the process parameters and modeling strategies are discussed.

Space Construction Automated Fabrication Experiment Definition Study (SCAFEDS), part 2

NASA Technical Reports Server (NTRS)

1978-01-01

The techniques, processes, and equipment required for automatic fabrication and assembly of structural elements in using Shuttle as a launch vehicle, and construction were defined. Additional construction systems operational techniques, processes, and equipment which can be developed and demonstrated in the same program to provide further risk reduction benefits to future large space systems were identified and examined.

Handbook for Implementing Agile in Department of Defense Information Technology Acquisition

DTIC Science & Technology

2010-12-15

Wire-frame Mockup of iTunes Cover Flow Feature (source: http://www.balsamiq.com/products/mockups/examples#mytunez...programming. The JOPES customer was included early in the development process in order to understand requirements management (story cards ), observe...transition by teaching the new members Agile processes, such as story card development, refactoring, and pair programming. Additionally, the team worked to

78 FR 53750 - EcoEléctrica, L.P.; Notice of Intent To Prepare an Environmental Assessment for the Proposed LNG...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-30

... Pe[ntilde]uelas, Puerto Rico. This EA will be used by the Commission in its decision-making process...) 502-8371. For instructions on connecting to eLibrary, refer to the ``Additional Information'' section... Process The National Environmental Policy Act (NEPA) requires the Commission to take into account the...

Influence of Postbuild Microstructure on the Electrochemical Behavior of Additively Manufactured 17-4 PH Stainless Steel

NASA Astrophysics Data System (ADS)

Stoudt, M. R.; Ricker, R. E.; Lass, E. A.; Levine, L. E.

2017-03-01

The additive manufacturing build process produces a segregated microstructure with significant variations in composition and phases that are uncommon in traditional wrought materials. As such, the relationship between the postbuild microstructure and the corrosion resistance is not well understood. Stainless steel alloy 17-4 precipitation hardened (SS17-4PH) is an industrially relevant alloy for applications requiring high strength and good corrosion resistance. A series of potentiodynamic scans conducted in a deaerated 0.5-mol/L NaCl solution evaluated the influence of these microstructural differences on the pitting behavior of SS17-4. The pitting potentials were found to be higher in the samples of additively processed material than in the samples of the alloy in wrought form. This indicates that the additively processed material is more resistant to localized corrosion and pitting in this environment than is the wrought alloy. The results also suggest that after homogenization, the additively produced SS17-4 could be more resistant to pitting than the wrought SS17-4 is in an actual service environment.

The Influence of Post-Build Microstructure on the Electrochemical Behavior of Additively Manufactured 17-4 PH Stainless Steel.

PubMed

Stoudt, M R; Ricker, R E; Lass, E A; Levine, L E

2017-03-01

The additive manufacturing (AM) build process produces a segregated microstructure with significant variations in composition and phases that are uncommon in traditional wrought materials. As such, the relationship between the post-build microstructure and the corrosion resistance is not well understood. Stainless steel alloy 17-4PH is an industrially-relevant alloy for applications requiring high-strength and good corrosion resistance. A series of potentiodynamic scans conducted in a deaerated 0.5 mol/L NaCl solution evaluated the influence of these microstructural differences on the pitting behavior of SS17-4. The pitting potentials were found to be higher in the samples of additively-processed material than in samples of the alloy in wrought form. This indicates that the additively-processed material is more resistant to localized corrosion and pitting in this environment than the wrought alloy. The results also suggest that after homogenization, the additively-produced SS17-4 could be more resistant to pitting than wrought SS17-4 in an actual service environment.

The Influence of Post-Build Microstructure on the Electrochemical Behavior of Additively Manufactured 17-4 PH Stainless Steel

PubMed Central

Stoudt, M. R.; Ricker, R. E.; Lass, E. A.; Levine, L. E.

2017-01-01

The additive manufacturing (AM) build process produces a segregated microstructure with significant variations in composition and phases that are uncommon in traditional wrought materials. As such, the relationship between the post-build microstructure and the corrosion resistance is not well understood. Stainless steel alloy 17-4PH is an industrially-relevant alloy for applications requiring high-strength and good corrosion resistance. A series of potentiodynamic scans conducted in a deaerated 0.5 mol/L NaCl solution evaluated the influence of these microstructural differences on the pitting behavior of SS17-4. The pitting potentials were found to be higher in the samples of additively-processed material than in samples of the alloy in wrought form. This indicates that the additively-processed material is more resistant to localized corrosion and pitting in this environment than the wrought alloy. The results also suggest that after homogenization, the additively-produced SS17-4 could be more resistant to pitting than wrought SS17-4 in an actual service environment. PMID:28757787

Birth of millisecond pulsars in globular clusters

NASA Technical Reports Server (NTRS)

Grindlay, J. E.; Bailyn, C. D.

1988-01-01

It is argued here that accretion-induced collapse of white dwarfs in binaries can form millisecond pulsars directly without requiring a precursor low-mass X-ray binary stage. Ablation of the precollapse binary companion by the millisecond pulsar's radiation field, a process invoked to explain some of the characteristics of the recently discovered eclipsing millisecond pulsar, can then yield isolated neutron stars witout requiring an additional stellar encounter.

Visual Purple, the Next Generation Crisis Management Decision Training Tool

DTIC Science & Technology

2001-09-01

talents of professional Hollywood screenwriters during the scripting and writing process of the simulations. Additionally, cinematic techniques learned...cultural, and language experts for research development. Additionally, GTA provides country specific support in script writing and cinematic resources as...The result is an entirely new dimension of realism that traditional exercises often fail to capture. The scenario requires the participant to make the

Influence of ferrite phase in alite-calcium sulfoaluminate cements

NASA Astrophysics Data System (ADS)

Duvallet, Tristana Yvonne Francoise

Since the energy crisis in 1970's, research on low energy cements with low CO2- emissions has been increasing. Numerous solutions have been investigated, and the goal of this original research is to create a viable hybrid cement with the components of both Ordinary Portland cement (OPC) and calcium sulfoaluminate cement (CSAC), by forming a material that contains both alite and calcium sulfoaluminate clinker phases. Furthermore, this research focuses on keeping the cost of this material reasonable by reducing aluminum requirements through its substitution with iron. The aim of this work would produce a cement that can use large amounts of red mud, which is a plentiful waste material, in place of bauxite known as an expensive raw material. Modified Bogue equations were established and tested to formulate this novel cement with different amounts of ferrite, from 5% to 45% by weight. This was followed by the production of cement from reagent chemicals, and from industrial by-products as feedstocks (fly ash, red mud and slag). Hydration processes, as well as the mechanical properties, of these clinker compositions were studied, along with the addition of gypsum and the impact of a ferric iron complexing additive triisopropanolamine (TIPA). To summarize this research, the influence of the addition of 5-45% by weight of ferrite phase, was examined with the goal of introducing as much red mud as possible in the process without negatively attenuate the cement properties. Based on this PhD dissertation, the production of high-iron alite-calcium sulfoaluminateferrite cements was proven possible from the two sources of raw materials. The hydration processes and the mechanical properties seemed negatively affected by the addition of ferrite, as this phase was not hydrated entirely, even after 6 months of curing. The usage of TIPA counteracted this decline in strength by improving the ferrite hydration and increasing the optimum amount of gypsum required in each composition. The mechanical data were equivalent to OPC strengths for some compositions with 25% ferrite. This preliminary work constitutes the first research phase of this novel cement and requires additional research for its improvement. Topics for additional research are identified in this dissertation. KEYWORDS: alite, calcium sulfoaluminate, ferrite, low-energy cement, triisopropanolamine.

Speed of perceptual grouping in acquired brain injury.

PubMed

Kurylo, Daniel D; Larkin, Gabriella Brick; Waxman, Richard; Bukhari, Farhan

2014-09-01

Evidence exists that damage to white matter connections may contribute to reduced speed of information processing in traumatic brain injury and stroke. Damage to such axonal projections suggests a particular vulnerability to functions requiring integration across cortical sites. To test this prediction, measurements were made of perceptual grouping, which requires integration of stimulus components. A group of traumatic brain injury and cerebral vascular accident patients and a group of age-matched healthy control subjects viewed arrays of dots and indicated the pattern into which stimuli were perceptually grouped. Psychophysical measurements were made of perceptual grouping as well as processing speed. The patient group showed elevated grouping thresholds as well as extended processing time. In addition, most patients showed progressive slowing of processing speed across levels of difficulty, suggesting reduced resources to accommodate increased demands on grouping. These results support the prediction that brain injury results in a particular vulnerability to functions requiring integration of information across the cortex, which may result from dysfunction of long-range axonal connection.

Capturing security requirements for software systems.

PubMed

El-Hadary, Hassan; El-Kassas, Sherif

2014-07-01

Security is often an afterthought during software development. Realizing security early, especially in the requirement phase, is important so that security problems can be tackled early enough before going further in the process and avoid rework. A more effective approach for security requirement engineering is needed to provide a more systematic way for eliciting adequate security requirements. This paper proposes a methodology for security requirement elicitation based on problem frames. The methodology aims at early integration of security with software development. The main goal of the methodology is to assist developers elicit adequate security requirements in a more systematic way during the requirement engineering process. A security catalog, based on the problem frames, is constructed in order to help identifying security requirements with the aid of previous security knowledge. Abuse frames are used to model threats while security problem frames are used to model security requirements. We have made use of evaluation criteria to evaluate the resulting security requirements concentrating on conflicts identification among requirements. We have shown that more complete security requirements can be elicited by such methodology in addition to the assistance offered to developers to elicit security requirements in a more systematic way.

Capturing security requirements for software systems

PubMed Central

El-Hadary, Hassan; El-Kassas, Sherif

2014-01-01

Security is often an afterthought during software development. Realizing security early, especially in the requirement phase, is important so that security problems can be tackled early enough before going further in the process and avoid rework. A more effective approach for security requirement engineering is needed to provide a more systematic way for eliciting adequate security requirements. This paper proposes a methodology for security requirement elicitation based on problem frames. The methodology aims at early integration of security with software development. The main goal of the methodology is to assist developers elicit adequate security requirements in a more systematic way during the requirement engineering process. A security catalog, based on the problem frames, is constructed in order to help identifying security requirements with the aid of previous security knowledge. Abuse frames are used to model threats while security problem frames are used to model security requirements. We have made use of evaluation criteria to evaluate the resulting security requirements concentrating on conflicts identification among requirements. We have shown that more complete security requirements can be elicited by such methodology in addition to the assistance offered to developers to elicit security requirements in a more systematic way. PMID:25685514

Implementationof a modular software system for multiphysical processes in porous media

NASA Astrophysics Data System (ADS)

Naumov, Dmitri; Watanabe, Norihiro; Bilke, Lars; Fischer, Thomas; Lehmann, Christoph; Rink, Karsten; Walther, Marc; Wang, Wenqing; Kolditz, Olaf

2016-04-01

Subsurface georeservoirs are a candidate technology for large scale energy storage required as part of the transition to renewable energy sources. The increased use of the subsurface results in competing interests and possible impacts on protected entities. To optimize and plan the use of the subsurface in large scale scenario analyses,powerful numerical frameworks are required that aid process understanding and can capture the coupled thermal (T), hydraulic (H), mechanical (M), and chemical (C) processes with high computational efficiency. Due to having a multitude of different couplings between basic T, H, M, or C processes and the necessity to implement new numerical schemes the development focus has moved to software's modularity. The decreased coupling between the components results in two major advantages: easier addition of specialized processes and improvement of the code's testability and therefore its quality. The idea of modularization is implemented on several levels, in addition to library based separation of the previous code version, by using generalized algorithms available in the Standard Template Library and the Boost library, relying on efficient implementations of liner algebra solvers, using concepts when designing new types, and localization of frequently accessed data structures. This procedure shows certain benefits for a flexible high-performance framework applied to the analysis of multipurpose georeservoirs.

Combustion process science and technology

NASA Technical Reports Server (NTRS)

Hale, Robert R.

1989-01-01

An important and substantial area of technical work in which noncontact temperature measurement (NCTM) is desired is that involving combustion process research. In the planning for this workshop, it was hoped that W. Serignano would provide a briefing regarding the experimental requirements for thermal measurements to support such research. The particular features of thermal measurement requirements included those describing the timeline for combustion experiments, the requirements for thermal control and diagnostics of temperature and other related thermal measurements and the criticality to the involved science to parametric features of measurement capability including precision, repeatability, stability, and resolution. In addition, it was hoped that definitions could be provided which characterize the needs for concurrent imaging as it relates to science observations during the conduct of experimentation.

Turnaround operations analysis for OTV. Volume 1: Executive summary

NASA Technical Reports Server (NTRS)

1988-01-01

Anaylses performed for ground processing, both expendable and reusable ground-based Orbital Transfer Vehicles (OTVs) launched on the Space Transportation System (STS), a reusable space-based OTV (SBOTV) launched on the STS, and a reusable ground-based OTV (GBOTV) launched on an unmanned cargo vehicle and recovered by the Orbiter are summarized. Also summarized are the analyses performed for space processing the reusable SBOTV at the Space Station in low Earth orbit (LEO) as well as the maintenance and servicing of the SBOTV accommodations at the Space Station. In addition, the candidate OTV concepts, design and interface requirements, and the Space Station design, support, and interface requirements are summarized. A development schedule and associated costs for the required SBOTV accommodations at the Space Station are presented. Finallly, the technology development plan to develop the capability to process both GBOTVs and SBOTVs are summarized.

Maneuver Recovery Analysis for the Magnetospheric Multiscale Mission

NASA Technical Reports Server (NTRS)

Gramling, Cheryl; Carpenter, Russell; Volle, Michael; Lee, Taesul; Long, Anne

2007-01-01

The use of spacecraft formations creates new and more demanding requirements for orbit determination accuracy. In addition to absolute navigation requirements, there are typically relative navigation requirements that are based on the size or shape of the formation. The difficulty in meeting these requirements is related to the relative dynamics of the spacecraft orbits and the frequency of the formation maintenance maneuvers. This paper examines the effects of bi-weekly formation maintenance maneuvers on the absolute and relative orbit determination accuracy for the four-spacecraft Magnetospheric Multiscale (MMS) formation. Results are presented from high fidelity simulations that include the effects of realistic orbit determination errors in the maneuver planning process. Solutions are determined using a high accuracy extended Kalman filter designed for onboard navigation. Three different solutions are examined, considering the effects of process noise and measurement rate on the solutions.

Robotic tape library system level testing at NSA: Present and planned

NASA Technical Reports Server (NTRS)

Shields, Michael F.

1994-01-01

In the present of declining Defense budgets, increased pressure has been placed on the DOD to utilize Commercial Off the Shelf (COTS) solutions to incrementally solve a wide variety of our computer processing requirements. With the rapid growth in processing power, significant expansion of high performance networking, and the increased complexity of applications data sets, the requirement for high performance, large capacity, reliable and secure, and most of all affordable robotic tape storage libraries has greatly increased. Additionally, the migration to a heterogeneous, distributed computing environment has further complicated the problem. With today's open system compute servers approaching yesterday's supercomputer capabilities, the need for affordable, reliable secure Mass Storage Systems (MSS) has taken on an ever increasing importance to our processing center's ability to satisfy operational mission requirements. To that end, NSA has established an in-house capability to acquire, test, and evaluate COTS products. Its goal is to qualify a set of COTS MSS libraries, thereby achieving a modicum of standardization for robotic tape libraries which can satisfy our low, medium, and high performance file and volume serving requirements. In addition, NSA has established relations with other Government Agencies to complete this in-house effort and to maximize our research, testing, and evaluation work. While the preponderance of the effort is focused at the high end of the storage ladder, considerable effort will be extended this year and next at the server class or mid range storage systems.

Overview of the production of sintered SiC optics and optical sub-assemblies

NASA Astrophysics Data System (ADS)

Williams, S.; Deny, P.

2005-08-01

The following is an overview on sintered silicon carbide (SSiC) material properties and processing requirements for the manufacturing of components for advanced technology optical systems. The overview will compare SSiC material properties to typical materials used for optics and optical structures. In addition, it will review manufacturing processes required to produce optical components in detail by process step. The process overview will illustrate current manufacturing process and concepts to expand the process size capability. The overview will include information on the substantial capital equipment employed in the manufacturing of SSIC. This paper will also review common in-process inspection methodology and design rules. The design rules are used to improve production yield, minimize cost, and maximize the inherent benefits of SSiC for optical systems. Optimizing optical system designs for a SSiC manufacturing process will allow systems designers to utilize SSiC as a low risk, cost competitive, and fast cycle time technology for next generation optical systems.

Advanced Process Possibilities in Friction Crush Welding of Aluminum, Steel, and Copper by Using an Additional Wire

NASA Astrophysics Data System (ADS)

Besler, Florian A.; Grant, Richard J.; Schindele, Paul; Stegmüller, Michael J. R.

2017-12-01

Joining sheet metal can be problematic using traditional friction welding techniques. Friction crush welding (FCW) offers a high speed process which requires a simple edge preparation and can be applied to out-of-plane geometries. In this work, an implementation of FCW was employed using an additional wire to weld sheets of EN AW5754 H22, DC01, and Cu-DHP. The joint is formed by bringing together two sheet metal parts, introducing a wire into the weld zone and employing a rotating disk which is subject to an external force. The requirements of the welding preparation and the fundamental process variables are shown. Thermal measurements were taken which give evidence about the maximum temperature in the welding center and the temperature in the periphery of the sheet metals being joined. The high welding speed along with a relatively low heat input results in a minimal distortion of the sheet metal and marginal metallurgical changes in the parent material. In the steel specimens, this FCW implementation produces a fine grain microstructure, enhancing mechanical properties in the region of the weld. Aluminum and copper produced mean bond strengths of 77 and 69 pct to that of the parent material, respectively, whilst the steel demonstrated a strength of 98 pct. Using a wire offers the opportunity to use a higher-alloyed additional material and to precisely adjust the additional material volume appropriate for a given material alignment and thickness.

Connecticut Department of Transportation safety techniques enhancement plan.

DOT National Transportation Integrated Search

2015-03-15

The Highway Safety Manual (HSM) defines a six-step cycle of safety management processes. This report evaluates the : Conncituct Department on how well conform to the six safety management steps. The methods recommended in the HSM : require additional...

Step 1: C3 Flight Demo Data Analysis Plan

NASA Technical Reports Server (NTRS)

2005-01-01

The Data Analysis Plan (DAP) describes the data analysis that the C3 Work Package (WP) will perform in support of the Access 5 Step 1 C3 flight demonstration objectives as well as the processes that will be used by the Flight IPT to gather and distribute the data collected to satisfy those objectives. In addition to C3 requirements, this document will encompass some Human Systems Interface (HSI) requirements in performing the C3 flight demonstrations. The C3 DAP will be used as the primary interface requirements document between the C3 Work Package and Flight Test organizations (Flight IPT and Non-Access 5 Flight Programs). In addition to providing data requirements for Access 5 flight test (piggyback technology demonstration flights, dedicated C3 technology demonstration flights, and Airspace Operations Demonstration flights), the C3 DAP will be used to request flight data from Non- Access 5 flight programs for C3 related data products

Phylogenetics beyond biology.

PubMed

Retzlaff, Nancy; Stadler, Peter F

2018-06-21

Evolutionary processes have been described not only in biology but also for a wide range of human cultural activities including languages and law. In contrast to the evolution of DNA or protein sequences, the detailed mechanisms giving rise to the observed evolution-like processes are not or only partially known. The absence of a mechanistic model of evolution implies that it remains unknown how the distances between different taxa have to be quantified. Considering distortions of metric distances, we first show that poor choices of the distance measure can lead to incorrect phylogenetic trees. Based on the well-known fact that phylogenetic inference requires additive metrics, we then show that the correct phylogeny can be computed from a distance matrix [Formula: see text] if there is a monotonic, subadditive function [Formula: see text] such that [Formula: see text] is additive. The required metric-preserving transformation [Formula: see text] can be computed as the solution of an optimization problem. This result shows that the problem of phylogeny reconstruction is well defined even if a detailed mechanistic model of the evolutionary process remains elusive.

Designing food structures for nutrition and health benefits.

PubMed

Norton, Jennifer E; Wallis, Gareth A; Spyropoulos, Fotis; Lillford, Peter J; Norton, Ian T

2014-01-01

In addition to providing specific sensory properties (e.g., flavor or textures), there is a need to produce foods that also provide functionality within the gastrointestinal (GI) tract, over and above simple nutrition. As such, there is a need to understand the physical and chemical processes occurring in the mouth, stomach, small intestine, and large intestine, in addition to the food structure-physiology interactions. In vivo techniques and in vitro models have allowed us to study and simulate these processes, which aids us in the design of food microstructures that can provide functionality within the human body. Furthermore, it is important to be aware of the health or nutritional needs of different groups of consumers when designing food structures, to provide targeted functionality. Examples of three groups of consumers (elderly, obese, and athletes) are given to demonstrate their differing nutritional requirements and the formulation engineering approaches that can be utilized to improve the health of these individuals. Eating is a pleasurable process, but foods of the future will be required to provide much more in terms of functionality for health and nutrition.

Evaluation of Braided Stiffener Concepts for Transport Aircraft Wing Structure Applications

NASA Technical Reports Server (NTRS)

Deaton, Jerry W.; Dexter, H. Benson (Editor); Markus, Alan; Rohwer, Kim

1995-01-01

Braided composite materials have potential for application in aircraft structures. Stiffeners, wing spars, floor beams, and fuselage frames are examples where braided composites could find application if cost effective processing and damage requirements are met. Braiding is an automated process for obtaining near-net shape preforms for fabrication of components for structural applications. Previous test results on braided composite materials obtained at NASA Langley indicate that damage tolerance requirements can be met for some applications. In addition, the braiding industry is taking steps to increase the material through-put to be more competitive with other preform fabrication processes. Data are presented on the compressive behavior of three braided stiffener preform fabric constructions as determined from individual stiffener crippling test and three stiffener wide panel tests. Stiffener and panel fabrication are described and compression data presented for specimens tested with and without impact damage. In addition, data are also presented on the compressive behavior of the stitched stiffener preform construction currently being used by McDonnell Douglas Aerospace in the NASA ACT wing development program.

Arginine-glycine-aspartic acid functional branched semi-interpenetrating hydrogels.

PubMed

Plenderleith, Richard A; Pateman, Christopher J; Rodenburg, Cornelia; Haycock, John W; Claeyssens, Frederik; Sammon, Chris; Rimmer, Stephen

2015-10-14

For the first time a series of functional hydrogels based on semi-interpenetrating networks with both branched and crosslinked polymer components have been prepared and we show the successful use of these materials as substrates for cell culture. The materials consist of highly branched poly(N-isopropyl acrylamide)s with peptide functionalised end groups in a continuous phase of crosslinked poly(vinyl pyrrolidone). Functionalisation of the end groups of the branched polymer component with the GRGDS peptide produces a hydrogel that supports cell adhesion and proliferation. The materials provide a new synthetic functional biomaterial that has many of the features of extracellular matrix, and as such can be used to support tissue regeneration and cell culture. This class of high water content hydrogel material has important advantages over other functional hydrogels in its synthesis and does not require post-processing modifications nor are functional-monomers, which change the polymerisation process, required. Thus, the systems are amenable to large scale and bespoke manufacturing using conventional moulding or additive manufacturing techniques. Processing using additive manufacturing is exemplified by producing tubes using microstereolithography.

Constant-Pressure Combustion Charts Including Effects of Diluent Addition

NASA Technical Reports Server (NTRS)

Turner, L Richard; Bogart, Donald

1949-01-01

Charts are presented for the calculation of (a) the final temperatures and the temperature changes involved in constant-pressure combustion processes of air and in products of combustion of air and hydrocarbon fuels, and (b) the quantity of hydrocarbon fuels required in order to attain a specified combustion temperature when water, alcohol, water-alcohol mixtures, liquid ammonia, liquid carbon dioxide, liquid nitrogen, liquid oxygen, or their mixtures are added to air as diluents or refrigerants. The ideal combustion process and combustion with incomplete heat release from the primary fuel and from combustible diluents are considered. The effect of preheating the mixture of air and diluents and the effect of an initial water-vapor content in the combustion air on the required fuel quantity are also included. The charts are applicable only to processes in which the final mixture is leaner than stoichiometric and at temperatures where dissociation is unimportant. A chart is also included to permit the calculation of the stoichiometric ratio of hydrocarbon fuel to air with diluent addition. The use of the charts is illustrated by numerical examples.

Parallel Processing of Images in Mobile Devices using BOINC

NASA Astrophysics Data System (ADS)

Curiel, Mariela; Calle, David F.; Santamaría, Alfredo S.; Suarez, David F.; Flórez, Leonardo

2018-04-01

Medical image processing helps health professionals make decisions for the diagnosis and treatment of patients. Since some algorithms for processing images require substantial amounts of resources, one could take advantage of distributed or parallel computing. A mobile grid can be an adequate computing infrastructure for this problem. A mobile grid is a grid that includes mobile devices as resource providers. In a previous step of this research, we selected BOINC as the infrastructure to build our mobile grid. However, parallel processing of images in mobile devices poses at least two important challenges: the execution of standard libraries for processing images and obtaining adequate performance when compared to desktop computers grids. By the time we started our research, the use of BOINC in mobile devices also involved two issues: a) the execution of programs in mobile devices required to modify the code to insert calls to the BOINC API, and b) the division of the image among the mobile devices as well as its merging required additional code in some BOINC components. This article presents answers to these four challenges.

Effects of build parameters on linear wear loss in plastic part produced by fused deposition modeling

NASA Astrophysics Data System (ADS)

Mohamed, Omar Ahmed; Masood, Syed Hasan; Bhowmik, Jahar Lal

2017-07-01

Fused Deposition Modeling (FDM) is one of the prominent additive manufacturing technologies for producing polymer products. FDM is a complex additive manufacturing process that can be influenced by many process conditions. The industrial demands required from the FDM process are increasing with higher level product functionality and properties. The functionality and performance of FDM manufactured parts are greatly influenced by the combination of many various FDM process parameters. Designers and researchers always pay attention to study the effects of FDM process parameters on different product functionalities and properties such as mechanical strength, surface quality, dimensional accuracy, build time and material consumption. However, very limited studies have been carried out to investigate and optimize the effect of FDM build parameters on wear performance. This study focuses on the effect of different build parameters on micro-structural and wear performance of FDM specimens using definitive screening design based quadratic model. This would reduce the cost and effort of additive manufacturing engineer to have a systematic approachto make decision among the manufacturing parameters to achieve the desired product quality.

Multi-track financing.

PubMed

Kennedy, Steven W; Randolph, John; Taddey, Anthony J

2012-05-01

In today's uncertain economic environment, when seeking to finance a capital project, healthcare borrowers should adopt a multi-tracked funding strategy that permits them to change capital-funding routes quickly in response to changing circumstances. The multi-tracking process requires two stages prior to securing a commitment and beginning the closing process: due diligence and indication of interest. This process should present no material additional cost during these two stages, giving healthcare borrowers the flexibility to explore a variety of financing options.

Analyses of requirements for computer control and data processing experiment subsystems: Image data processing system (IDAPS) software description (7094 version), volume 2

NASA Technical Reports Server (NTRS)

1973-01-01

A description of each of the software modules of the Image Data Processing System (IDAPS) is presented. The changes in the software modules are the result of additions to the application software of the system and an upgrade of the IBM 7094 Mod(1) computer to a 1301 disk storage configuration. Necessary information about IDAPS sofware is supplied to the computer programmer who desires to make changes in the software system or who desires to use portions of the software outside of the IDAPS system. Each software module is documented with: module name, purpose, usage, common block(s) description, method (algorithm of subroutine) flow diagram (if needed), subroutines called, and storage requirements.

Ion-Selective Deposition of Manganese Sulphate Solution from Trenggalek Manganese Ore by Active Carbon and Sodium Hydroxide

NASA Astrophysics Data System (ADS)

Andriyah, L.; Sulistiyono, E.

2017-02-01

One of the step in manganese dioxide manufacturing process for battery industry is a purification process of lithium manganese sulphate solution. The elimination of impurities such as iron removal is important in hydrometallurgical processes. Therefore, this paper present the purification results of manganese sulphate solution by removing impurities using a selective deposition method, namely activated carbon adsorption and NaOH. The experimental results showed that the optimum condition of adsorption process occurs on the addition of 5 g adsorbent and the addition of 10 ml NaOH 1 N, processing time of 30 minutes and the best is the activated carbon adsorption of Japan. Because the absolute requirement of the cathode material of lithium ion manganese are free of titanium then of local wood charcoal is good enough in terms of eliminating ions Ti is equal to 70.88%.

pySeismicDQA: open source post experiment data quality assessment and processing

NASA Astrophysics Data System (ADS)

Polkowski, Marcin

2017-04-01

Seismic Data Quality Assessment is python based, open source set of tools dedicated for data processing after passive seismic experiments. Primary goal of this toolset is unification of data types and formats from different dataloggers necessary for further processing. This process requires additional data checks for errors, equipment malfunction, data format errors, abnormal noise levels, etc. In all such cases user needs to decide (manually or by automatic threshold) if data is removed from output dataset. Additionally, output dataset can be visualized in form of website with data availability charts and waveform visualization with earthquake catalog (external). Data processing can be extended with simple STA/LTA event detection. pySeismicDQA is designed and tested for two passive seismic experiments in central Europe: PASSEQ 2006-2008 and "13 BB Star" (2013-2016). National Science Centre Poland provided financial support for this work via NCN grant DEC-2011/02/A/ST10/00284.

Generic waste management requirements for a controlled ecological life support system /CELSS/

NASA Technical Reports Server (NTRS)

Hoshizaki, T.; Hansen, B. D., III

1981-01-01

Regenerative life support systems for future space missions will require closure of the waste-food loop. Each mission application will generate specific requirements for the waste management system. However, there are generic input and output requirements that can be identified when a probable scenario is chosen. This paper discusses the generic requirements when higher plants are chosen as the primary food source. Attention is focused on the quality and quantity of nutrients necessary for culturing higher plants. The types of wastes to be processed are also discussed. In addition, requirements generated by growing plants on three different substrates are presented. This work suggests that the mineral composition of waste materials may require minimal adjustment to satisfy the plant requirements.

21 CFR 212.30 - What requirements must my facilities and equipment meet?

Code of Federal Regulations, 2014 CFR

2014-04-01

... could reasonably be expected to adversely affect the identity, strength, quality, or purity of a PET..., in-process materials, or PET drugs are not reactive, additive, or absorptive so as to alter the quality of PET drugs. ...

21 CFR 212.30 - What requirements must my facilities and equipment meet?

Code of Federal Regulations, 2012 CFR

2012-04-01

... could reasonably be expected to adversely affect the identity, strength, quality, or purity of a PET..., in-process materials, or PET drugs are not reactive, additive, or absorptive so as to alter the quality of PET drugs. ...

21 CFR 212.30 - What requirements must my facilities and equipment meet?

Code of Federal Regulations, 2013 CFR

2013-04-01

... could reasonably be expected to adversely affect the identity, strength, quality, or purity of a PET..., in-process materials, or PET drugs are not reactive, additive, or absorptive so as to alter the quality of PET drugs. ...

What Fermenter?

ERIC Educational Resources Information Center

Terry, John

1987-01-01

Discusses the feasibility of using fermenters in secondary school laboratories. Includes discussions of equipment, safety, and computer interfacing. Describes how a simple fermenter could be used to simulate large-scale processes. Concludes that, although teachers and technicians will require additional training, the prospects for biotechnology in…

Development of Finer Spatial Resolution Optical Properties from MODIS

DTIC Science & Technology

2008-02-04

infrared (SWIR) channels at 1240 nm and 2130 run. The increased resolution spectral Rrs channels are input into bio-optical algorithms (Quasi...processes. Additionally, increased resolution is required for validation of ocean color products in coastal regions due to the shorter spatial scales of...with in situ Rrs data to determine the "best" method in coastal regimes. We demonstrate that finer resolution is required for validation of coastal

Alloy steel nuts for bolting for high-pressure and high-temperature service (ASME SA-194 with additional requirements)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This standard covers alloy steel nuts for bolting for high-pressure and high-temperature service in nuclear and associated applications. This standard does not cover bar or other starting materials. The only implied special considerations for starting materials are that they be capable of passing the required tests when processed into finished products in accordance with this standard.

Bibliography On Multiprocessors And Distributed Processing

NASA Technical Reports Server (NTRS)

Miya, Eugene N.

1988-01-01

Multiprocessor and Distributed Processing Bibliography package consists of large machine-readable bibliographic data base, which in addition to usual keyword searches, used for producing citations, indexes, and cross-references. Data base contains UNIX(R) "refer" -formatted ASCII data and implemented on any computer running under UNIX(R) operating system. Easily convertible to other operating systems. Requires approximately one megabyte of secondary storage. Bibliography compiled in 1985.

K-9 training aids made using additive manufacturing

DOEpatents

Reynolds, John G.; Durban, Matthew M.; Gash, Alexander E.; Grapes, Michael D.; Kelley, Ryan S.; Sullivan, Kyle T.

2018-02-20

Additive Manufacturing (AM) is used to make aids that target the training of K-9s to detect explosives. The process uses mixtures of explosives and matrices commonly used in AM. The explosives are formulated into a mixture with the matrix and printed using AM techniques and equipment. The explosive concentrations are kept less than 10% by wt. of the mixture to conform to requirements of shipping and handling.

X-33 Environmental Impact Statement: A Fast Track Approach

NASA Technical Reports Server (NTRS)

McCaleb, Rebecca C.; Holland, Donna L.

1998-01-01

NASA is required by the National Environmental Policy Act (NEPA) to prepare an appropriate level environmental analysis for its major projects. Development of the X-33 Technology Demonstrator and its associated flight test program required an environmental impact statement (EIS) under the NEPA. The EIS process is consists of four parts: the "Notice of Intent" to prepare an EIS and scoping; the draft EIS which is distributed for review and comment; the final ETS; and the "Record of Decision." Completion of this process normally takes from 2 - 3 years, depending on the complexity of the proposed action. Many of the agency's newest fast track, technology demonstration programs require NEPA documentation, but cannot sustain the lengthy time requirement between program concept development to implementation. Marshall Space Flight Center, in cooperation with Kennedy Space Center, accomplished the NEPA process for the X-33 Program in 13 months from Notice of Intent to Record of Decision. In addition, the environmental team implemented an extensive public involvement process, conducting a total of 23 public meetings for scoping and draft EIS comment along with numerous informal meetings with public officials, civic organizations, and Native American Indians. This paper will discuss the fast track approach used to successfully accomplish the NEPA process for X-33 on time.

NASA Handbook for Models and Simulations: An Implementation Guide for NASA-STD-7009

NASA Technical Reports Server (NTRS)

Steele, Martin J.

2013-01-01

The purpose of this Handbook is to provide technical information, clarification, examples, processes, and techniques to help institute good modeling and simulation practices in the National Aeronautics and Space Administration (NASA). As a companion guide to NASA-STD- 7009, Standard for Models and Simulations, this Handbook provides a broader scope of information than may be included in a Standard and promotes good practices in the production, use, and consumption of NASA modeling and simulation products. NASA-STD-7009 specifies what a modeling and simulation activity shall or should do (in the requirements) but does not prescribe how the requirements are to be met, which varies with the specific engineering discipline, or who is responsible for complying with the requirements, which depends on the size and type of project. A guidance document, which is not constrained by the requirements of a Standard, is better suited to address these additional aspects and provide necessary clarification. This Handbook stems from the Space Shuttle Columbia Accident Investigation (2003), which called for Agency-wide improvements in the "development, documentation, and operation of models and simulations"' that subsequently elicited additional guidance from the NASA Office of the Chief Engineer to include "a standard method to assess the credibility of the models and simulations."2 General methods applicable across the broad spectrum of model and simulation (M&S) disciplines were sought to help guide the modeling and simulation processes within NASA and to provide for consistent reporting ofM&S activities and analysis results. From this, the standardized process for the M&S activity was developed. The major contents of this Handbook are the implementation details of the general M&S requirements ofNASA-STD-7009, including explanations, examples, and suggestions for improving the credibility assessment of an M&S-based analysis.

Test Capability Enhancements to the NASA Langley 8-Foot High Temperature Tunnel

NASA Technical Reports Server (NTRS)

Harvin, S. F.; Cabell, K. F.; Gallimore, S. D.; Mekkes, G. L.

2006-01-01

The NASA Langley 8-Foot High Temperature Tunnel produces true enthalpy environments simulating flight from Mach 4 to Mach 7, primarily for airbreathing propulsion and aerothermal/thermo-structural testing. Flow conditions are achieved through a methane-air heater and nozzles producing aerodynamic Mach numbers of 4, 5 or 7 and have exit diameters of 8 feet or 4.5 feet. The 12-ft long free-jet test section, housed inside a 26-ft vacuum sphere, accommodates large test articles. Recently, the facility underwent significant upgrades to support hydrocarbon fueled scramjet engine testing and to expand flight simulation capability. The upgrades were required to meet engine system development and flight clearance verification requirements originally defined by the joint NASA-Air Force X-43C Hypersonic Flight Demonstrator Project and now the Air Force X-51A Program. Enhancements to the 8-Ft. HTT were made in four areas: 1) hydrocarbon fuel delivery; 2) flight simulation capability; 3) controls and communication; and 4) data acquisition/processing. The upgrades include the addition of systems to supply ethylene and liquid JP-7 to test articles; a Mach 5 nozzle with dynamic pressure simulation capability up to 3200 psf, the addition of a real-time model angle-of-attack system; a new programmable logic controller sub-system to improve process controls and communication with model controls; the addition of MIL-STD-1553B and high speed data acquisition systems and a classified data processing environment. These additions represent a significant increase to the already unique test capability and flexibility of the facility, and complement the existing array of test support hardware such as a model injection system, radiant heaters, six-component force measurement system, and optical flow field visualization hardware. The new systems support complex test programs that require sophisticated test sequences and precise management of process fluids. Furthermore, the new systems, such as the real-time angle of attack system and the new programmable logic controller enhance the test efficiency of the facility. The motivation for the upgrades and the expanded capabilities is described here.

Automated Cellient(™) cytoblocks: better, stronger, faster?

PubMed

Prendeville, S; Brosnan, T; Browne, T J; McCarthy, J

2014-12-01

Cytoblocks (CBs), or cell blocks, provide additional morphological detail and a platform for immunocytochemistry (ICC) in cytopathology. The Cellient(™) system produces CBs in 45 minutes using methanol fixation, compared with traditional CBs, which require overnight formalin fixation. This study compares Cellient and traditional CB methods in terms of cellularity, morphology and immunoreactivity, evaluates the potential to add formalin fixation to the Cellient method for ICC studies and determines the optimal sectioning depth for maximal cellularity in Cellient CBs. One hundred and sixty CBs were prepared from 40 cytology samples (32 malignant, eight benign) using four processing methods: (A) traditional; (B) Cellient (methanol fixation); (C) Cellient using additional formalin fixation for 30 minutes; (D) Cellient using additional formalin fixation for 60 minutes. Haematoxylin and eosin-stained sections were assessed for cellularity and morphology. ICC was assessed on 14 cases with a panel of antibodies. Three additional Cellient samples were serially sectioned to determine the optimal sectioning depth. Scoring was performed by two independent, blinded reviewers. For malignant cases, morphology was superior with Cellient relative to traditional CBs (P < 0.001). Cellularity was comparable across all methods. ICC was excellent in all groups and the addition of formalin at any stage during the Cellient process did not influence the staining quality. Serial sectioning through Cellient CBs showed optimum cellularity at 30-40 μm with at least 27 sections obtainable. Cellient CBs provide superior morphology to traditional CBs and, if required, formalin fixation may be added to the Cellient process for ICC. Optimal Cellient CB cellularity is achieved at 30-40 μm, which will impact on the handling of cases in daily practice. © 2014 John Wiley & Sons Ltd.

Mars Atmospheric Capture and Gas Separation

NASA Technical Reports Server (NTRS)

Muscatello, Anthony; Santiago-Maldonado, Edgardo; Gibson, Tracy; Devor, Robert; Captain, James

2011-01-01

The Mars atmospheric capture and gas separation project is selecting, developing, and demonstrating techniques to capture and purify Martian atmospheric gases for their utilization for the production of hydrocarbons, oxygen, and water in ISRU systems. Trace gases will be required to be separated from Martian atmospheric gases to provide pure C02 to processing elements. In addition, other Martian gases, such as nitrogen and argon, occur in concentrations high enough to be useful as buffer gas and should be captured as welL To achieve these goals, highly efficient gas separation processes will be required. These gas separation techniques are also required across various areas within the ISRU project to support various consumable production processes. The development of innovative gas separation techniques will evaluate the current state-of-the-art for the gas separation required, with the objective to demonstrate and develop light-weight, low-power methods for gas separation. Gas separation requirements include, but are not limited to the selective separation of: (1) methane and water from un-reacted carbon oxides (C02- CO) and hydrogen typical of a Sabatier-type process, (2) carbon oxides and water from unreacted hydrogen from a Reverse Water-Gas Shift process, (3) carbon oxides from oxygen from a trash/waste processing reaction, and (4) helium from hydrogen or oxygen from a propellant scavenging process. Potential technologies for the separations include freezers, selective membranes, selective solvents, polymeric sorbents, zeolites, and new technologies. This paper and presentation will summarize the results of an extensive literature review and laboratory evaluations of candidate technologies for the capture and separation of C02 and other relevant gases.

Power management and distribution considerations for a lunar base

NASA Technical Reports Server (NTRS)

Kenny, Barbara H.; Coleman, Anthony S.

1991-01-01

Design philosophies and technology needs for the power management and distribution (PMAD) portion of a lunar base power system are discussed. A process is described whereby mission planners may proceed from a knowledge of the PMAD functions and mission performance requirements to a definition of design options and technology needs. Current research efforts at the NASA LRC to meet the PMAD system needs for a Lunar base are described. Based on the requirements, the lunar base PMAD is seen as best being accomplished by a utility like system, although with some additional demands including autonomous operation and scheduling and accurate, predictive modeling during the design process.

[Development method of healthcare information system integration based on business collaboration model].

PubMed

Li, Shasha; Nie, Hongchao; Lu, Xudong; Duan, Huilong

2015-02-01

Integration of heterogeneous systems is the key to hospital information construction due to complexity of the healthcare environment. Currently, during the process of healthcare information system integration, people participating in integration project usually communicate by free-format document, which impairs the efficiency and adaptability of integration. A method utilizing business process model and notation (BPMN) to model integration requirement and automatically transforming it to executable integration configuration was proposed in this paper. Based on the method, a tool was developed to model integration requirement and transform it to integration configuration. In addition, an integration case in radiology scenario was used to verify the method.

Fabrication of Thermoelectric Devices Using Additive-Subtractive Manufacturing Techniques: Application to Waste-Heat Energy Harvesting

NASA Astrophysics Data System (ADS)

Tewolde, Mahder

Thermoelectric generators (TEGs) are solid-state devices that convert heat directly into electricity. They are well suited for waste-heat energy harvesting applications as opposed to primary energy generation. Commercially available thermoelectric modules are flat, inflexible and have limited sizes available. State-of-art manufacturing of TEG devices relies on assembling prefabricated parts with soldering, epoxy bonding, and mechanical clamping. Furthermore, efforts to incorporate them onto curved surfaces such as exhaust pipes, pump housings, steam lines, mixing containers, reaction chambers, etc. require custom-built heat exchangers. This is costly and labor-intensive, in addition to presenting challenges in terms of space, thermal coupling, added weight and long-term reliability. Additive manufacturing technologies are beginning to address many of these issues by reducing part count in complex designs and the elimination of sub-assembly requirements. This work investigates the feasibility of utilizing such novel manufacturing routes for improving the manufacturing process of thermoelectric devices. Much of the research in thermoelectricity is primarily focused on improving thermoelectric material properties by developing of novel materials or finding ways to improve existing ones. Secondary to material development is improving the manufacturing process of TEGs to provide significant cost benefits. To improve the device fabrication process, this work explores additive manufacturing technologies to provide an integrated and scalable approach for TE device manufacturing directly onto engineering component surfaces. Additive manufacturing techniques like thermal spray and ink-dispenser printing are developed with the aim of improving the manufacturing process of TEGs. Subtractive manufacturing techniques like laser micromachining are also studied in detail. This includes the laser processing parameters for cutting the thermal spray materials efficiently by optimizing cutting speed and power while maintaining surface quality and interface properties. Key parameters are obtained from these experiments and used to develop a process that can be used to fabricate a working TEG directly onto the waste-heat component surface. A TEG module has been fabricated for the first time entirely by using thermal spray technology and laser micromachining. The target applications include automotive exhaust systems and other high-volume industrial waste heat sources. The application of TEGs for thermoelectrically powered sensors for Small Modular Reactors (SMRs) is presented. In conclusion, more ways to improve the fabrication process of TEGs are suggested.

Investigation of charge coupled device correlation techniques

NASA Technical Reports Server (NTRS)

Lampe, D. R.; Lin, H. C.; Shutt, T. J.

1978-01-01

Analog Charge Transfer Devices (CTD's) offer unique advantages to signal processing systems, which often have large development costs, making it desirable to define those devices which can be developed for general system's use. Such devices are best identified and developed early to give system's designers some interchangeable subsystem blocks, not requiring additional individual development for each new signal processing system. The objective of this work is to describe a discrete analog signal processing device with a reasonably broad system use and to implement its design, fabrication, and testing.

Image processing techniques and applications to the Earth Resources Technology Satellite program

NASA Technical Reports Server (NTRS)

Polge, R. J.; Bhagavan, B. K.; Callas, L.

1973-01-01

The Earth Resources Technology Satellite system is studied, with emphasis on sensors, data processing requirements, and image data compression using the Fast Fourier and Hadamard transforms. The ERTS-A system and the fundamentals of remote sensing are discussed. Three user applications (forestry, crops, and rangelands) are selected and their spectral signatures are described. It is shown that additional sensors are needed for rangeland management. An on-board information processing system is recommended to reduce the amount of data transmitted.

Additive Manufacturing of Porous Metal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dehoff, Ryan R.; Kirka, Michael M.

2017-06-01

Currently, helium is obtained through separation from natural gas. The current industrial process incurs significant costs and requires large energy resources to successfully achieve separation. Through utilizing Additive Manufacturing (AM) technologies it is possible to reduce both of these burdens when refining helium gas. The ability to engineer porosity levels within Inconel 718 discs for controlled separation of helium from natural gas was investigated. Arrays of samples fabricated using the electron beam melting process were analyzed for their relative porosity density. Based upon the measurements, full scale discs were fabricated, and subsequently tested to determine their effectiveness in separating heliummore » from liquefied natural gas.« less

Polysilicon planarization and plug recess etching in a decoupled plasma source chamber using two endpoint techniques

NASA Astrophysics Data System (ADS)

Kaplita, George A.; Schmitz, Stefan; Ranade, Rajiv; Mathad, Gangadhara S.

1999-09-01

The planarization and recessing of polysilicon to form a plug are processes of increasing importance in silicon IC fabrication. While this technology has been developed and applied to DRAM technology using Trench Storage Capacitors, the need for such processes in other IC applications (i.e. polysilicon studs) has increased. Both planarization and recess processes usually have stringent requirements on etch rate, recess uniformity, and selectivity to underlying films. Additionally, both processes generally must be isotropic, yet must not expand any seams that might be present in the polysilicon fill. These processes should also be insensitive to changes in exposed silicon area (pattern factor) on the wafer. A SF6 plasma process in a polysilicon DPS (Decoupled Plasma Source) reactor has demonstrated the capability of achieving the above process requirements for both planarization and recess etch. The SF6 process in the decoupled plasma source reactor exhibited less sensitivity to pattern factor than in other types of reactors. Control of these planarization and recess processes requires two endpoint systems to work sequentially in the same recipe: one for monitoring the endpoint when blanket polysilicon (100% Si loading) is being planarized and one for monitoring the recess depth while the plug is being recessed (less than 10% Si loading). The planarization process employs an optical emission endpoint system (OES). An interferometric endpoint system (IEP), capable of monitoring lateral interference, is used for determining the recess depth. The ability of using either or both systems is required to make these plug processes manufacturable. Measuring the recess depth resulting from the recess process can be difficult, costly and time- consuming. An Atomic Force Microscope (AFM) can greatly alleviate these problems and can serve as a critical tool in the development of recess processes.

What drives successful implementation of pollution prevention and cleaner technology strategy? The role of innovative capability.

PubMed

Bhupendra, Kumar Verma; Sangle, Shirish

2015-05-15

Firms that are dynamic and prepared to implement environmental strategies have a potential competitive advantage over their industry counterparts. Therefore, it is important to understand, what capabilities are required to implement proactive environmental strategies. The paper discusses the attributes of innovative capability required by firms in order to adopt pollution prevention and cleaner technology strategies. Empirical results show that process and behavioral innovativeness are required by firms to implement a pollution prevention strategy. In addition to process and behavioral innovativeness, firms need a top management with high risk-taking ability as well as market, product, and strategic innovativeness to implement a cleaner technology strategy. The paper proposes some important managerial implications on the basis of the above research findings. Copyright © 2015 Elsevier Ltd. All rights reserved.

The work of the European Union Reference Laboratory for Food Additives (EURL) and its support for the authorisation process of feed additives in the European Union: a review

PubMed Central

von Holst, Christoph; Robouch, Piotr; Bellorini, Stefano; de la Huebra, María José González; Ezerskis, Zigmas

2016-01-01

ABSTRACT This paper describes the operation of the European Union Reference Laboratory for Feed Additives (EURL) and its role in the authorisation procedure of feed additives in the European Union. Feed additives are authorised according to Regulation (EC) No. 1831/2003, which introduced a completely revised authorisation procedure and also established the EURL. The regulations authorising feed additives contain conditions of use such as legal limits of the feed additives, which require the availability of a suitable method of analysis for official control purposes under real world conditions. It is the task of the EURL to evaluate the suitability of analytical methods as proposed by the industry for this purpose. Moreover, the paper shows that one of the major challenges is the huge variety of the methodology applied in feed additive analysis, thus requiring expertise in quite different analytical areas. In order to cope with this challenge, the EURL is supported by a network of national reference laboratories (NRLs) and only the merged knowledge of all NRLs allows for a scientifically sound assessment of the analytical methods. PMID:26540604

CROSS-CUTTING QA ISSUES INVOLVING GEOSPATIAL SCIENCES, CHEMISTRY, INFORMATION MANAGEMENT, AND LAW

EPA Science Inventory

The Agency spends hundreds of millions of dollars annually collecting and processing environmental data for scientific research and regulatory decision making. In addition, the regulated community may spend as much or more each year responding to Agency compliance requirements. ...

50 CFR 648.127 - Framework adjustments to management measures.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., FMP Monitoring Committee composition and process, description and identification of essential fish... additions to management measures must come from one or more of the following categories: Minimum fish size, maximum fish size, gear restrictions, gear restricted areas, gear requirements or prohibitions, permitting...

40 CFR 240.200-2 - Recommended procedures: Design.

Code of Federal Regulations, 2011 CFR

2011-07-01

....200-2 Section 240.200-2 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES GUIDELINES FOR THE THERMAL PROCESSING OF SOLID WASTES Requirements and Recommended Procedures § 240.200-2 Recommended procedures: Design. (a) In addition to the residential and commercial wastes...

40 CFR 240.200-2 - Recommended procedures: Design.

Code of Federal Regulations, 2010 CFR

2010-07-01

....200-2 Section 240.200-2 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES GUIDELINES FOR THE THERMAL PROCESSING OF SOLID WASTES Requirements and Recommended Procedures § 240.200-2 Recommended procedures: Design. (a) In addition to the residential and commercial wastes...

75 FR 68702 - Regulation SHO

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-09

... extended compliance period will give industry participants additional time for programming and testing for... time for programming and testing for compliance with the Rule's requirements. We have been informed that there have been some delays in the programming process, due in part to certain information, which...

Multimedia Networks: Mission Impossible?

ERIC Educational Resources Information Center

Weiss, Andrew M.

1996-01-01

Running multimedia on a network, often difficult because of the memory and processing power required, is becoming easier thanks to new protocols and products. Those developing network design criteria may wish to consider making use of Fast Ethernet, Asynchronous Transfer Method (ATM), switches, "fat pipes", additional network…

49 CFR 229.211 - Processing of petitions.

Code of Federal Regulations, 2012 CFR

2012-10-01

... to the U.S. Department of Transportation Docket Operations (M-30), West Building Ground Floor, Room... requires additional information to appropriately consider the petition, FRA will conduct a hearing on the..., or both which may include validated computer modeling, structural crush analysis, component testing...

49 CFR 229.211 - Processing of petitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

... to the U.S. Department of Transportation Docket Operations (M-30), West Building Ground Floor, Room... requires additional information to appropriately consider the petition, FRA will conduct a hearing on the..., or both which may include validated computer modeling, structural crush analysis, component testing...

49 CFR 229.211 - Processing of petitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

... to the U.S. Department of Transportation Docket Operations (M-30), West Building Ground Floor, Room... requires additional information to appropriately consider the petition, FRA will conduct a hearing on the..., or both which may include validated computer modeling, structural crush analysis, component testing...

78 FR 41014 - Online Political File and Petition for Reconsideration

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-09

... Political File and Petition for Reconsideration AGENCY: Federal Communications Commission. ACTION: Notice... of the rules requiring broadcast television stations to post their political files online, and on a... instructions for submitting comments and additional information on the rulemaking process, see the...

Automata learning algorithms and processes for providing more complete systems requirements specification by scenario generation, CSP-based syntax-oriented model construction, and R2D2C system requirements transformation

NASA Technical Reports Server (NTRS)

Margaria, Tiziana (Inventor); Hinchey, Michael G. (Inventor); Rouff, Christopher A. (Inventor); Rash, James L. (Inventor); Steffen, Bernard (Inventor)

2010-01-01

Systems, methods and apparatus are provided through which in some embodiments, automata learning algorithms and techniques are implemented to generate a more complete set of scenarios for requirements based programming. More specifically, a CSP-based, syntax-oriented model construction, which requires the support of a theorem prover, is complemented by model extrapolation, via automata learning. This may support the systematic completion of the requirements, the nature of the requirement being partial, which provides focus on the most prominent scenarios. This may generalize requirement skeletons by extrapolation and may indicate by way of automatically generated traces where the requirement specification is too loose and additional information is required.

Lightning Protection System for HE Facilities at LLNL - Certification Template

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clancy, T J; Ong, M M; Brown, C G

2005-12-08

This document is meant as a template to assist in the development of your own lighting certification process. Aside from this introduction and the mock representative name of the building (Building A), this document is nearly identical to a lightning certification report issued by the Engineering Directorate at Lawrence Livermore National Laboratory. At the date of this release, we have certified over 70 HE processing and storage cells at our Site 300 facilities. In Chapters 1 and 2 respectively, we address the need and methods of lightning certification for HE processing and storage facilities at LLNL. We present the preferredmore » method of lightning protection in Chapter 3, as well as the likely building modifications that are needed to comply with this method. In Chapter 4, we present the threat assessment and resulting safe work areas within a cell. After certification, there may be changes to operations during a lightning alert, and this is discussed in Chapter 5. Chapter 6 lists the maintenance requirements for the continuation of lighting certification status. Appendices of this document are meant as an aid in developing your own certification process, and they include a bonding list, an inventory of measurement equipment, surge suppressors in use at LLNL, an Integrated Work and Safety form (IWS), and a template certification sign-off sheet. The lightning certification process involves more that what is spelled out in this document. The first steps involve considerable planning, the securing of funds, and management and explosives safety buy-in. Permits must be obtained, measurement equipment must be assembled and tested, and engineers and technicians must be trained in their use. Cursory building inspections are also recommended, and surge suppression for power systems must be addressed. Upon completion of a certification report and its sign-off by management, additional work is required. Training will be needed in order to educate workers and facility managers of the requirements of lightning certification. Operating procedures will need to be generated and/or modified with additional controls. Engineering controls may also be implemented requiring the modification of cells. Careful planning should bring most of these issues to light, making it clear where this document is helpful and were additional assistance may be necessary.« less

Membrane thickening aerobic digestion processes.

PubMed

Woo, Bryen

2014-01-01

Sludge management accounts for approximately 60% of the total wastewater treatment plant expenditure and laws for sludge disposal are becoming increasingly stringent, therefore much consideration is required when designing a solids handling process. A membrane thickening aerobic digestion process integrates a controlled aerobic digestion process with pre-thickening waste activated sludge using membrane technology. This process typically features an anoxic tank, an aerated membrane thickener operating in loop with a first-stage digester followed by second-stage digestion. Membrane thickening aerobic digestion processes can handle sludge from any liquid treatment process and is best for facilities obligated to meet low total phosphorus and nitrogen discharge limits. Membrane thickening aerobic digestion processes offer many advantages including: producing a reusable quality permeate with minimal levels of total phosphorus and nitrogen that can be recycled to the head works of a plant, protecting the performance of a biological nutrient removal liquid treatment process without requiring chemical addition, providing reliable thickening up to 4% solids concentration without the use of polymers or attention to decanting, increasing sludge storage capacities in existing tanks, minimizing the footprint of new tanks, reducing disposal costs, and providing Class B stabilization.

Non-rigid CT/CBCT to CBCT registration for online external beam radiotherapy guidance

NASA Astrophysics Data System (ADS)

Zachiu, Cornel; de Senneville, Baudouin Denis; Tijssen, Rob H. N.; Kotte, Alexis N. T. J.; Houweling, Antonetta C.; Kerkmeijer, Linda G. W.; Lagendijk, Jan J. W.; Moonen, Chrit T. W.; Ries, Mario

2018-01-01

Image-guided external beam radiotherapy (EBRT) allows radiation dose deposition with a high degree of accuracy and precision. Guidance is usually achieved by estimating the displacements, via image registration, between cone beam computed tomography (CBCT) and computed tomography (CT) images acquired at different stages of the therapy. The resulting displacements are then used to reposition the patient such that the location of the tumor at the time of treatment matches its position during planning. Moreover, ongoing research aims to use CBCT-CT image registration for online plan adaptation. However, CBCT images are usually acquired using a small number of x-ray projections and/or low beam intensities. This often leads to the images being subject to low contrast, low signal-to-noise ratio and artifacts, which ends-up hampering the image registration process. Previous studies addressed this by integrating additional image processing steps into the registration procedure. However, these steps are usually designed for particular image acquisition schemes, therefore limiting their use on a case-by-case basis. In the current study we address CT to CBCT and CBCT to CBCT registration by the means of the recently proposed EVolution registration algorithm. Contrary to previous approaches, EVolution does not require the integration of additional image processing steps in the registration scheme. Moreover, the algorithm requires a low number of input parameters, is easily parallelizable and provides an elastic deformation on a point-by-point basis. Results have shown that relative to a pure CT-based registration, the intrinsic artifacts present in typical CBCT images only have a sub-millimeter impact on the accuracy and precision of the estimated deformation. In addition, the algorithm has low computational requirements, which are compatible with online image-based guidance of EBRT treatments.

Validation study and routine control monitoring of moist heat sterilization procedures.

PubMed

Shintani, Hideharu

2012-06-01

The proposed approach to validation of steam sterilization in autoclaves follows the basic life cycle concepts applicable to all validation programs. Understand the function of sterilization process, develop and understand the cycles to carry out the process, and define a suitable test or series of tests to confirm that the function of the process is suitably ensured by the structure provided. Sterilization of product and components and parts that come in direct contact with sterilized product is the most critical of pharmaceutical processes. Consequently, this process requires a most rigorous and detailed approach to validation. An understanding of the process requires a basic understanding of microbial death, the parameters that facilitate that death, the accepted definition of sterility, and the relationship between the definition and sterilization parameters. Autoclaves and support systems need to be designed, installed, and qualified in a manner that ensures their continued reliability. Lastly, the test program must be complete and definitive. In this paper, in addition to validation study, documentation of IQ, OQ and PQ concretely were described.

Description of the AILS Alerting Algorithm

NASA Technical Reports Server (NTRS)

Samanant, Paul; Jackson, Mike

2000-01-01

This document provides a complete description of the Airborne Information for Lateral Spacing (AILS) alerting algorithms. The purpose of AILS is to provide separation assurance between aircraft during simultaneous approaches to closely spaced parallel runways. AILS will allow independent approaches to be flown in such situations where dependent approaches were previously required (typically under Instrument Meteorological Conditions (IMC)). This is achieved by providing multiple levels of alerting for pairs of aircraft that are in parallel approach situations. This document#s scope is comprehensive and covers everything from general overviews, definitions, and concepts down to algorithmic elements and equations. The entire algorithm is presented in complete and detailed pseudo-code format. This can be used by software programmers to program AILS into a software language. Additional supporting information is provided in the form of coordinate frame definitions, data requirements, calling requirements as well as all necessary pre-processing and post-processing requirements. This is important and required information for the implementation of AILS into an analysis, a simulation, or a real-time system.

Manufacture of ammonium sulfate fertilizer from gypsum-rich byproduct of flue gas desulfurization - A prefeasibility cost estimate

USGS Publications Warehouse

Chou, I.-Ming; Rostam-Abadi, M.; Lytle, J.M.; Achorn, F.P.

1996-01-01

Costs for constructing and operating a conceptual plant based on a proposed process that converts flue gas desulfurization (FGD)-gypsum to ammonium sulfate fertilizer has been calculated and used to estimate a market price for the product. The average market price of granular ammonium sulfate ($138/ton) exceeds the rough estimated cost of ammonium sulfate from the proposed process ($111/ ton), by 25 percent, if granular size ammonium sulfate crystals of 1.2 to 3.3 millimeters in diameters can be produced by the proposed process. However, there was at least ??30% margin in the cost estimate calculations. The additional costs for compaction, if needed to create granules of the required size, would make the process uneconomical unless considerable efficiency gains are achieved to balance the additional costs. This study suggests the need both to refine the crystallization process and to find potential markets for the calcium carbonate produced by the process.

Space Station communications and tracking system

NASA Technical Reports Server (NTRS)

Dietz, Reinhold H.

1987-01-01

A comprehensive description of the existing Space Station communications and tracking system requirements, architecture, and design concepts is provided. Areas which will require innovative solutions to provide cost-effective flight systems are emphasized. Among these are the space-to-space links, the differential global positioning system for determining relative position with free-flying vehicles, multitarget radar, packet/isochronous signal processing, and laser docking systems. In addition, the importance of advanced development, tests, and analyses is summarized.

Orthorectified High Resolution Multispectral Imagery for Application to Change Detection and Analysis

NASA Technical Reports Server (NTRS)

Benkelman, Cody A.

1997-01-01

The project team has outlined several technical objectives which will allow the companies to improve on their current capabilities. These include modifications to the imaging system, enabling it to operate more cost effectively and with greater ease of use, automation of the post-processing software to mosaic and orthorectify the image scenes collected, and the addition of radiometric calibration to greatly aid in the ability to perform accurate change detection. Business objectives include fine tuning of the market plan plus specification of future product requirements, expansion of sales activities (including identification of necessary additional resources required to meet stated revenue objectives), development of a product distribution plan, and implementation of a world wide sales effort.

Experiment requirements and implementation plan (Erip) for semiconductor materials growth in low-G environment

NASA Technical Reports Server (NTRS)

Crouch, R. K.; Fripp, A. L.; Debnam, W. J.; Clark, I. O.

1983-01-01

The MEA-2 A facility was used to test the effect of the low gravity environment on suppressing convective mixing in the growth of Pb(1-x)Sn(x)Te crystals. The need to eliminate convection, the furnace characteristics and operation that will be required for successful experimental implementation, and to the level that is presently known, the measured physical properties of the Pb(1-x)Sn(x)Te system were discussed. In addition, a brief background of the present and potential utilization of Pb(1-x)Sn(x)Te is given. Additional experiments are anticipated in future MEA-A, improved MEA and other dedicated materials processing in space flight apparatus.

[Recombinant granulocyte-colony stimulating factor (filgrastim): optimization of conditions of isolation and purification from inclusion body].

PubMed

Kononova, N V; Iakovlev, A V; Zhuravko, A M; Pankeev, N N; Minaev, S V; Bobruskin, A I; Mart'ianov, V A

2014-01-01

We developed a unified process platform for two recombinant human GCSF medicines--one with the non-prolonged and the other with prolonged action. This unified technology led to a simpler and cheaper production while introduction of the additional pegylation stage to the technological line eased obtaining of the medicines with different action and allowed to standardize technological process documenting according to GMP requirements.

Formation of Ketenimines via the Palladium-Catalyzed Decarboxylative π-Allylic Rearrangement of N-Alloc Ynamides.

PubMed

Alexander, Juliana R; Cook, Matthew J

2017-11-03

A new approach for the formation of ketenimines via a decarboxylative allylic rearrangement pathway that does not require strong stabilizing or protecting groups has been developed. The products can be readily hydrolyzed into their corresponding secondary amides or reacted with sulfur ylides to perform an additional [2,3]-Wittig process. Mechanistic studies suggest an outer-sphere process in which reductive alkylation is rate-limiting.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bernardin, John D; Baca, Allen G

This paper presents the mechanical design, fabrication and dynamic testing of an electrostatic analyzer spacecraft instrument. The functional and environmental requirements combined with limited spacecraft accommodations, resulted in complex component geometries, unique material selections, and difficult fabrication processes. The challenging aspects of the mechanical design and several of the more difficult production processes are discussed. In addition, the successes, failures, and lessons learned from acoustic and random vibration testing of a full-scale prototype instrument are presented.

Acoustic Data Processing and Transient Signal Analysis for the Hybrid Wing Body 14- by 22-Foot Subsonic Wind Tunnel Test

NASA Technical Reports Server (NTRS)

Bahr, Christopher J.; Brooks, Thomas F.; Humphreys, William M.; Spalt, Taylor B.; Stead, Daniel J.

2014-01-01

An advanced vehicle concept, the HWB N2A-EXTE aircraft design, was tested in NASA Langley's 14- by 22-Foot Subsonic Wind Tunnel to study its acoustic characteristics for var- ious propulsion system installation and airframe con gurations. A signi cant upgrade to existing data processing systems was implemented, with a focus on portability and a re- duction in turnaround time. These requirements were met by updating codes originally written for a cluster environment and transferring them to a local workstation while en- abling GPU computing. Post-test, additional processing of the time series was required to remove transient hydrodynamic gusts from some of the microphone time series. A novel automated procedure was developed to analyze and reject contaminated blocks of data, under the assumption that the desired acoustic signal of interest was a band-limited sta- tionary random process, and of lower variance than the hydrodynamic contamination. The procedure is shown to successfully identify and remove contaminated blocks of data and retain the desired acoustic signal. Additional corrections to the data, mainly background subtraction, shear layer refraction calculations, atmospheric attenuation and microphone directivity corrections, were all necessary for initial analysis and noise assessments. These were implemented for the post-processing of spectral data, and are shown to behave as expected.

Rapid process for producing transparent, monolithic porous glass

DOEpatents

Coronado, Paul R [Livermore, CA

2006-02-14

A process for making transparent porous glass monoliths from gels. The glass is produced much faster and in much larger sizes than present technology for making porous glass. The process reduces the cost of making large porous glass monoliths because: 1) the process does not require solvent exchange nor additives to the gel to increase the drying rates, 2) only moderate temperatures and pressures are used so relatively inexpensive equipment is needed, an 3) net-shape glass monoliths are possible using this process. The process depends on the use of temperature to control the partial pressure of the gel solvent in a closed vessel, resulting in controlled shrinking during drying.

Numerical and Experimental Study of Ti6Al4V Components Manufactured Using Powder Bed Fusion Additive Manufacturing

NASA Astrophysics Data System (ADS)

Zielinski, Jonas; Mindt, Hans-Wilfried; Düchting, Jan; Schleifenbaum, Johannes Henrich; Megahed, Mustafa

2017-12-01

Powder bed fusion additive manufacturing of titanium alloys is an interesting manufacturing route for many applications requiring high material strength combined with geometric complexity. Managing powder bed fusion challenges, including porosity, surface finish, distortions and residual stresses of as-built material, is the key to bringing the advantages of this process to production main stream. This paper discusses the application of experimental and numerical analysis towards optimizing the manufacturing process of a demonstration component. Powder characterization including assessment of the reusability, assessment of material consolidation and process window optimization is pursued prior to applying the identified optima to study the distortion and residual stresses of the demonstrator. Comparisons of numerical predictions with measurements show good correlations along the complete numerical chain.

The minicell TMirradiator: A new system for a new market

NASA Astrophysics Data System (ADS)

Clouser, James F.; Beers, Eric W.

1998-06-01

Since the commissioning of the first industrial Gamma Irradiator design, designers and operators of irradiation systems have been attempting to meet the specific production requirements and challenges presented to them. This objective has resulted in many different versions of irradiators currently in service today, all of which had original charters and many of which still perform very well within even the new requirements of this industry. Continuing changes in the marketplace have, however, placed pressures on existing designs due to a combination of changing dose requirements for sterlization, increased economic pressures from the specific industry served for both time and location and the increasing variety of product types requiring processing. Additionally, certain market areas which could never economically support a typical gamma processing facility have either not been serviced, or have forced potential gamma users to transport product long distances to one of these existing facilities. The MiniCell TM removes many of the traditional barriers previously accepted in the radiation processing industry for building a processing facility in a location. Its reduced size and cost have allowed many potential users to consider in-house processing and its ability to be quickly assembled allow it to meet market needs in a much more timely fashion than the previous designs. The MiniCell system can cost effectively meet many of the current market needs of reducing total cost of processing and also be flexible enough to process product in a wide range of industries effectively.

21 CFR 1311.302 - Additional application provider requirements.

Code of Federal Regulations, 2010 CFR

2010-04-01

... part, the application provider must notify practitioners or pharmacies that use the application as soon... practitioners or pharmacies with updates to any issue that makes the application non-compliant with the... practitioner or pharmacy may use the application to issue or process electronic controlled substance...

78 FR 8686 - Establishment of the National Freight Network

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-06

... Network AGENCY: Federal Highway Administration (FHWA), DOT. ACTION: Notice. SUMMARY: This notice defines the planned process for the designation of the national freight network as required by Section 1115 of... the initial designation of the primary freight network, the designation of additional miles critical...

77 FR 76435 - Connect America Fund

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-28

... excluding Phase I fiber from Phase II support is that the Bureau would not likely receive information... carriers should be restricted in building fiber, what information carriers should be required to provide... additional information on the rulemaking process, see the SUPPLEMENTARY INFORMATION section of this document...

Obtaining Reimbursement in France and Italy for New Diabetes Products

PubMed Central

Schaefer, Elmar; Sonsalla, Jessica

2015-01-01

Manufacturers launching next-generation or innovative medical devices in Europe face a very heterogeneous reimbursement landscape, with each country having its own pathways, timing, requirements and success factors. We selected 2 markets for a deeper look into the reimbursement landscape: France, representing a country with central decision making with defined processes, and Italy, which delegates reimbursement decisions to the regional level, resulting in a less transparent approach to reimbursement. Based on our experience in working on various new product launches and analyzing recent reimbursement decisions, we found that payers in both countries do not reward improved next-generation products with incremental reimbursement. Looking at innovations, we observe that manufacturers face a challenging and lengthy process to obtain reimbursement. In addition, requirements and key success factors differ by country: In France, comparative clinical evidence and budget impact very much drive reimbursement decisions in terms of pricing and restrictions, whereas in Italy, regional key opinion leader (KOL) support and additional local observational data are key. PMID:25550411

Obtaining reimbursement in France and Italy for new diabetes products.

PubMed

Schaefer, Elmar; Schnell, Gerald; Sonsalla, Jessica

2015-01-01

Manufacturers launching next-generation or innovative medical devices in Europe face a very heterogeneous reimbursement landscape, with each country having its own pathways, timing, requirements and success factors. We selected 2 markets for a deeper look into the reimbursement landscape: France, representing a country with central decision making with defined processes, and Italy, which delegates reimbursement decisions to the regional level, resulting in a less transparent approach to reimbursement. Based on our experience in working on various new product launches and analyzing recent reimbursement decisions, we found that payers in both countries do not reward improved next-generation products with incremental reimbursement. Looking at innovations, we observe that manufacturers face a challenging and lengthy process to obtain reimbursement. In addition, requirements and key success factors differ by country: In France, comparative clinical evidence and budget impact very much drive reimbursement decisions in terms of pricing and restrictions, whereas in Italy, regional key opinion leader (KOL) support and additional local observational data are key. © 2015 Diabetes Technology Society.

Retinoic acid induces nuclear accumulation of Raf1 during differentiation of HL-60 cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, James; Bunaciu, Rodica P.; Reiterer, Gudrun

All trans-retinoic acid (RA) is a standard therapeutic agent used in differentiation induction therapy treatment of acute promyelocytic leukemia (APL). RA and its metabolites use a diverse set of signal transduction pathways during the differentiation program. In addition to the direct transcriptional targets of the nuclear RAR and RXR receptors, signals derived from membrane receptors and the Raf-MEK-ERK pathway are required. Raf1 phosphorylation and the prolonged activation of Raf1 persisting during the entire differentiation process are required for RA-dependent differentiation of HL-60 cells. Here we identify a nuclear redistribution of Raf1 during the RA-induced differentiation of HL-60 cells. In addition,more » the nuclear accumulation of Raf1 correlates with an increase in Raf1 phosphorylated at serine 621. The serine 621 phosphorylated Raf1 is predominantly localized in the nucleus. The RA-dependent nuclear accumulation of Raf1 suggests a novel nuclear role for Raf1 during the differentiation process.« less

Is Semantic Processing During Sentence Reading Autonomous or Controlled? Evidence from the N400 Component in a Dual Task Paradigm

PubMed Central

Hohlfeld, Annette; Martín-Loeches, Manuel; Sommer, Werner

2015-01-01

The present study contributes to the discussion on the automaticity of semantic processing. Whereas most previous research investigated semantic processing at word level, the present study addressed semantic processing during sentence reading. A dual task paradigm was combined with the recording of event-related brain potentials. Previous research at word level processing reported different patterns of interference with the N400 by additional tasks: attenuation of amplitude or delay of latency. In the present study, we presented Spanish sentences that were semantically correct or contained a semantic violation in a critical word. At different intervals preceding the critical word a tone was presented that required a high-priority choice response. At short intervals/high temporal overlap between the tasks mean amplitude of the N400 was reduced relative to long intervals/low temporal overlap, but there were no shifts of peak latency. We propose that processing at sentence level exerts a protective effect against the additional task. This is in accord with the attentional sensitization model (Kiefer & Martens, 2010), which suggests that semantic processing is an automatic process that can be enhanced by the currently activated task set. The present experimental sentences also induced a P600, which is taken as an index of integrative processing. Additional task effects are comparable to those in the N400 time window and are briefly discussed. PMID:26203312

TARGET's role in knowledge acquisition, engineering, validation, and documentation

NASA Technical Reports Server (NTRS)

Levi, Keith R.

1994-01-01

We investigate the use of the TARGET task analysis tool for use in the development of rule-based expert systems. We found TARGET to be very helpful in the knowledge acquisition process. It enabled us to perform knowledge acquisition with one knowledge engineer rather than two. In addition, it improved communication between the domain expert and knowledge engineer. We also found it to be useful for both the rule development and refinement phases of the knowledge engineering process. Using the network in these phases required us to develop guidelines that enabled us to easily translate the network into production rules. A significant requirement for TARGET remaining useful throughout the knowledge engineering process was the need to carefully maintain consistency between the network and the rule representations. Maintaining consistency not only benefited the knowledge engineering process, but also has significant payoffs in the areas of validation of the expert system and documentation of the knowledge in the system.

Fostering radical conceptual change through dual-situated learning model

NASA Astrophysics Data System (ADS)

She, Hsiao-Ching

2004-02-01

This article examines how the Dual-Situated Learning Model (DSLM) facilitates a radical change of concepts that involve the understanding of matter, process, and hierarchical attributes. The DSLM requires knowledge of students' prior beliefs of science concepts and the nature of these concepts. In addition, DSLM also serves two functions: it creates dissonance with students' prior knowledge by challenging their epistemological and ontological beliefs about science concepts, and it provides essential mental sets for students to reconstruct a more scientific view of the concepts. In this study, the concept heat transfer: heat conduction and convection, which requires an understanding of matter, process, and hierarchical attributes, was chosen to examine how DSLM can facilitate radical conceptual change among students. Results show that DSLM has great potential to foster a radical conceptual change process in learning heat transfer. Radical conceptual change can definitely be achieved and does not necessarily involve a slow or gradual process.

Guiding gate-etch process development using 3D surface reaction modeling for 7nm and beyond

NASA Astrophysics Data System (ADS)

Dunn, Derren; Sporre, John R.; Deshpande, Vaibhav; Oulmane, Mohamed; Gull, Ronald; Ventzek, Peter; Ranjan, Alok

2017-03-01

Increasingly, advanced process nodes such as 7nm (N7) are fundamentally 3D and require stringent control of critical dimensions over high aspect ratio features. Process integration in these nodes requires a deep understanding of complex physical mechanisms to control critical dimensions from lithography through final etch. Polysilicon gate etch processes are critical steps in several device architectures for advanced nodes that rely on self-aligned patterning approaches to gate definition. These processes are required to meet several key metrics: (a) vertical etch profiles over high aspect ratios; (b) clean gate sidewalls free of etch process residue; (c) minimal erosion of liner oxide films protecting key architectural elements such as fins; and (e) residue free corners at gate interfaces with critical device elements. In this study, we explore how hybrid modeling approaches can be used to model a multi-step finFET polysilicon gate etch process. Initial parts of the patterning process through hardmask assembly are modeled using process emulation. Important aspects of gate definition are then modeled using a particle Monte Carlo (PMC) feature scale model that incorporates surface chemical reactions.1 When necessary, species and energy flux inputs to the PMC model are derived from simulations of the etch chamber. The modeled polysilicon gate etch process consists of several steps including a hard mask breakthrough step (BT), main feature etch steps (ME), and over-etch steps (OE) that control gate profiles at the gate fin interface. An additional constraint on this etch flow is that fin spacer oxides are left intact after final profile tuning steps. A natural optimization required from these processes is to maximize vertical gate profiles while minimizing erosion of fin spacer films.2

A shape-based account for holistic face processing.

PubMed

Zhao, Mintao; Bülthoff, Heinrich H; Bülthoff, Isabelle

2016-04-01

Faces are processed holistically, so selective attention to 1 face part without any influence of the others often fails. In this study, 3 experiments investigated what type of facial information (shape or surface) underlies holistic face processing and whether generalization of holistic processing to nonexperienced faces requires extensive discrimination experience. Results show that facial shape information alone is sufficient to elicit the composite face effect (CFE), 1 of the most convincing demonstrations of holistic processing, whereas facial surface information is unnecessary (Experiment 1). The CFE is eliminated when faces differ only in surface but not shape information, suggesting that variation of facial shape information is necessary to observe holistic face processing (Experiment 2). Removing 3-dimensional (3D) facial shape information also eliminates the CFE, indicating the necessity of 3D shape information for holistic face processing (Experiment 3). Moreover, participants show similar holistic processing for faces with and without extensive discrimination experience (i.e., own- and other-race faces), suggesting that generalization of holistic processing to nonexperienced faces requires facial shape information, but does not necessarily require further individuation experience. These results provide compelling evidence that facial shape information underlies holistic face processing. This shape-based account not only offers a consistent explanation for previous studies of holistic face processing, but also suggests a new ground-in addition to expertise-for the generalization of holistic processing to different types of faces and to nonface objects. (c) 2016 APA, all rights reserved).

Fabrication of multilayered conductive polymer structures via selective visible light photopolymerization

NASA Astrophysics Data System (ADS)

Cullen, Andrew T.; Price, Aaron D.

2017-04-01

Electropolymerization of pyrrole is commonly employed to fabricate intrinsically conductive polymer films that exhibit desirable electromechanical properties. Due to their monolithic nature, electroactive polypyrrole films produced via this process are typically limited to simple linear or bending actuation modes, which has hindered their application in complex actuation tasks. This initiative aims to develop the specialized fabrication methods and polymer formulations required to realize three-dimensional conductive polymer structures capable of more elaborate actuation modes. Our group has previously reported the application of the digital light processing additive manufacturing process for the fabrication of three-dimensional conductive polymer structures using ultraviolet radiation. In this investigation, we further expand upon this initial work and present an improved polymer formulation designed for digital light processing additive manufacturing using visible light. This technology enables the design of novel electroactive polymer sensors and actuators with enhanced capabilities and brings us one step closer to realizing more advanced electroactive polymer enabled devices.

Macro-/Micro-Controlled 3D Lithium-Ion Batteries via Additive Manufacturing and Electric Field Processing.

PubMed

Li, Jie; Liang, Xinhua; Liou, Frank; Park, Jonghyun

2018-01-30

This paper presents a new concept for making battery electrodes that can simultaneously control macro-/micro-structures and help address current energy storage technology gaps and future energy storage requirements. Modern batteries are fabricated in the form of laminated structures that are composed of randomly mixed constituent materials. This randomness in conventional methods can provide a possibility of developing new breakthrough processing techniques to build well-organized structures that can improve battery performance. In the proposed processing, an electric field (EF) controls the microstructures of manganese-based electrodes, while additive manufacturing controls macro-3D structures and the integration of both scales. The synergistic control of micro-/macro-structures is a novel concept in energy material processing that has considerable potential for providing unprecedented control of electrode structures, thereby enhancing performance. Electrochemical tests have shown that these new electrodes exhibit superior performance in their specific capacity, areal capacity, and life cycle.

In-Situ monitoring and modeling of metal additive manufacturing powder bed fusion

NASA Astrophysics Data System (ADS)

Alldredge, Jacob; Slotwinski, John; Storck, Steven; Kim, Sam; Goldberg, Arnold; Montalbano, Timothy

2018-04-01

One of the major challenges in metal additive manufacturing is developing in-situ sensing and feedback control capabilities to eliminate build errors and allow qualified part creation without the need for costly and destructive external testing. Previously, many groups have focused on high fidelity numerical modeling and true temperature thermal imaging systems. These approaches require large computational resources or costly hardware that requires complex calibration and are difficult to integrate into commercial systems. In addition, due to the rapid change in the state of the material as well as its surface properties, getting true temperature is complicated and difficult. Here, we describe a different approach where we implement a low cost thermal imaging solution allowing for relative temperature measurements sufficient for detecting unwanted process variability. We match this with a faster than real time qualitative model that allows the process to be rapidly modeled during the build. The hope is to combine these two, allowing for the detection of anomalies in real time, enabling corrective action to potentially be taken, or parts to be stopped immediately after the error, saving material and time. Here we describe our sensor setup, its costs and abilities. We also show the ability to detect in real time unwanted process deviations. We also show that the output of our high speed model agrees qualitatively with experimental results. These results lay the groundwork for our vision of an integrated feedback and control scheme that combines low cost, easy to use sensors and fast modeling for process deviation monitoring.

Requirements Analysis Study for Master Pump Shutdown System Project Development Specification [SEC 1 and 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

BEVINS, R.R.

This document has been updated during the definitive design portion of the first phase of the W-314 Project to capture additional software requirements and is planned to be updated during the second phase of the W-314 Project to cover the second phase of the Project's scope. The objective is to provide requirement traceability by recording the analysis/basis for the functional descriptions of the master pump shutdown system. This document identifies the sources of the requirements and/or how these were derived. Each requirement is validated either by quoting the source or an analysis process involving the required functionality, performance characteristics, operationsmore » input or engineering judgment.« less

Protecting and Respecting the Vulnerable: Existing Regulations or Further Protections?

PubMed Central

Solomon, Stephanie R.

2013-01-01

Scholars and policymakers continue to struggle over the meaning of the word “vulnerable” in the context of research ethics. One major reason for the stymied discussions regarding vulnerable populations is that there is no clear distinction between accounts of research vulnerabilities that exist for certain populations and discussions of research vulnerabilities that require special regulations in the context of research ethics policies. I suggest an analytic process by which to ascertain whether particular vulnerable populations should be contenders for additional regulatory protections. I apply this process to two vulnerable populations: the cognitively vulnerable and the economically vulnerable. I conclude that a subset of the cognitively vulnerable require extra protections while the economically vulnerable should be protected by implementing existing regulations more appropriately and rigorously. Unless or until the informed consent process is more adequately implemented and the distributive justice requirement of the Belmont Report is emphasized and operationalized, the economically disadvantaged will remain particularly vulnerable to the harm of exploitation in research. PMID:23329228

A closed life-support system for space colonies

NASA Technical Reports Server (NTRS)

Johnson, R. D.; Jebens, H. J.; Sweet, H. C.

1977-01-01

In 1975, a system design study was performed to examine a completely self-contained system for a permanent colony of 10,000 inhabitants in space. Fundamental to this design was the life support system. Since resupply from earth is prohibitive in transportation costs, it was decided to use a closed system with the initial supply of oxygen coming from processing of lunar ores, and the supply of carbon, nitrogen and hydrogen from earth. The problem of life support was treated starting with the nutritional and metabolic requirements for the human population, creating a food and water chain sufficient to supply these demands, adding the additional requirements for the animal and plant sources in the food chain, feeding back useful waste products, supplying water as required from different sources, and closing the loop by processing organic wastes into CO2. This concept places the burden of the system upon plants for O2 generation and waste processing the CO2 generation.

Protecting and respecting the vulnerable: existing regulations or further protections?

PubMed

Solomon, Stephanie R

2013-02-01

Scholars and policymakers continue to struggle over the meaning of the word "vulnerable" in the context of research ethics. One major reason for the stymied discussions regarding vulnerable populations is that there is no clear distinction between accounts of research vulnerabilities that exist for certain populations and discussions of research vulnerabilities that require special regulations in the context of research ethics policies. I suggest an analytic process by which to ascertain whether particular vulnerable populations should be contenders for additional regulatory protections. I apply this process to two vulnerable populations: the cognitively vulnerable and the economically vulnerable. I conclude that a subset of the cognitively vulnerable require extra protections while the economically vulnerable should be protected by implementing existing regulations more appropriately and rigorously. Unless or until the informed consent process is more adequately implemented and the distributive justice requirement of the Belmont Report is emphasized and operationalized, the economically disadvantaged will remain particularly vulnerable to the harm of exploitation in research.

An OSEE Based Portable Surface Contamination Monitor

NASA Technical Reports Server (NTRS)

Perey, Daniel F.

1997-01-01

Many industrial and aerospace processes involving the joining of materials, require sufficient surface cleanliness to insure proper bonding. Processes as diverse as painting, welding, or the soldering of electronic circuits will be compromised if prior inspection and removal of surface contaminants is inadequate. As process requirements become more stringent and the number of different materials and identified contaminants increases, various instruments and techniques have been developed for improved inspection. One such technique based on the principle of Optically Stimulated Electron Emission (OSEE) has been explored for a number of years as a tool for surface contamination monitoring. Some of the benefits of OSEE are: it's non-contacting; requires little operator training; and has very high contamination sensitivity. This paper describes the development of a portable OSEE based surface contamination monitor. The instrument is suitable for both hand-held and robotic inspections with either manual or automated control of instrument operation. In addition, instrument output data is visually displayed to the operator and may be output to an external computer for archiving or analysis.

A Review of Selective Laser Melted NiTi Shape Memory Alloy

PubMed Central

Khoo, Zhong Xun; Shen, Yu Fang

2018-01-01

NiTi shape memory alloys (SMAs) have the best combination of properties among the different SMAs. However, the limitations of conventional manufacturing processes and the poor manufacturability of NiTi have critically limited its full potential applicability. Thus, additive manufacturing, commonly known as 3D printing, has the potential to be a solution in fabricating complex NiTi smart structures. Recently, a number of studies on Selective Laser Melting (SLM) of NiTi were conducted to explore the various aspects of SLM-produced NiTi. Compared to producing conventional metals through the SLM process, the fabrication of NiTi SMA is much more challenging. Not only do the produced parts require a high density that leads to good mechanical properties, strict composition control is needed as well for the SLM NiTi to possess suitable phase transformation characteristics. Additionally, obtaining a good shape memory effect from the SLM NiTi samples is another challenging task that requires further understanding. This paper presents the results of the effects of energy density and SLM process parameters on the properties of SLM NiTi. Its shape memory properties and potential applications were then reviewed and discussed. PMID:29596320

Rapid production of hollow SS316 profiles by extrusion based additive manufacturing

NASA Astrophysics Data System (ADS)

Rane, Kedarnath; Cataldo, Salvatore; Parenti, Paolo; Sbaglia, Luca; Mussi, Valerio; Annoni, Massimiliano; Giberti, Hermes; Strano, Matteo

2018-05-01

Complex shaped stainless steel tubes are often required for special purpose biomedical equipment. Nevertheless, traditional manufacturing technologies, such as extrusion, lack the ability to compete in a market of customized complex components because of associated expenses towards tooling and extrusion presses. To rapid manufacture few of such components with low cost and high precision, a new Extrusion based Additive Manufacturing (EAM) process, is proposed in this paper, and as an example, short stainless steel 316L complex shaped and sectioned tubes were prepared by EAM. Several sample parts were produced using this process; the dimensional stability, surface roughness and chemical composition of sintered samples were investigated to prove process competence. The results indicate that feedstock with a 316L particle content of 92.5 wt. % can be prepared with a sigma blade mixing, whose rheological behavior is fit for EAM. The green samples have sufficient strength to handle them for subsequent treatments. The sintered samples considerably shrunk to designed dimensions and have a homogeneous microstructure to impart mechanical strength. Whereas, maintaining comparable dimensional accuracy and chemical composition which are required for biomedical equipment still need iterations, a kinematic correction and modification in debinding cycle was proposed.

A high-throughput system for high-quality tomographic reconstruction of large datasets at Diamond Light Source

PubMed Central

Atwood, Robert C.; Bodey, Andrew J.; Price, Stephen W. T.; Basham, Mark; Drakopoulos, Michael

2015-01-01

Tomographic datasets collected at synchrotrons are becoming very large and complex, and, therefore, need to be managed efficiently. Raw images may have high pixel counts, and each pixel can be multidimensional and associated with additional data such as those derived from spectroscopy. In time-resolved studies, hundreds of tomographic datasets can be collected in sequence, yielding terabytes of data. Users of tomographic beamlines are drawn from various scientific disciplines, and many are keen to use tomographic reconstruction software that does not require a deep understanding of reconstruction principles. We have developed Savu, a reconstruction pipeline that enables users to rapidly reconstruct data to consistently create high-quality results. Savu is designed to work in an ‘orthogonal’ fashion, meaning that data can be converted between projection and sinogram space throughout the processing workflow as required. The Savu pipeline is modular and allows processing strategies to be optimized for users' purposes. In addition to the reconstruction algorithms themselves, it can include modules for identification of experimental problems, artefact correction, general image processing and data quality assessment. Savu is open source, open licensed and ‘facility-independent’: it can run on standard cluster infrastructure at any institution. PMID:25939626

Noiseless intensity amplification of repetitive signals by coherent addition using the temporal Talbot effect

PubMed Central

Maram, Reza; Van Howe, James; Li, Ming; Azaña, José

2014-01-01

Amplification of signal intensity is essential for initiating physical processes, diagnostics, sensing, communications and measurement. During traditional amplification, the signal is amplified by multiplying the signal carriers through an active gain process, requiring the use of an external power source. In addition, the signal is degraded by noise and distortions that typically accompany active gain processes. We show noiseless intensity amplification of repetitive optical pulse waveforms with gain from 2 to ~20 without using active gain. The proposed method uses a dispersion-induced temporal self-imaging (Talbot) effect to redistribute and coherently accumulate energy of the original repetitive waveforms into fewer replica waveforms. In addition, we show how our passive amplifier performs a real-time average of the wave-train to reduce its original noise fluctuation, as well as enhances the extinction ratio of pulses to stand above the noise floor. Our technique is applicable to repetitive waveforms in any spectral region or wave system. PMID:25319207

An extended supersonic combustion model for the dynamic analysis of hypersonic vehicles

NASA Technical Reports Server (NTRS)

Bossard, J. A.; Peck, R. E.; Schmidt, D. K.

1993-01-01

The development of an advanced dynamic model for aeroelastic hypersonic vehicles powered by air breathing engines requires an adequate engine model. This report provides a discussion of some of the more important features of supersonic combustion and their relevance to the analysis and design of supersonic ramjet engines. Of particular interest are those aspects of combustion that impact the control of the process. Furthermore, the report summarizes efforts to enhance the aeropropulsive/aeroelastic dynamic model developed at the Aerospace Research Center of Arizona State University by focusing on combustion and improved modeling of this flow. The expanded supersonic combustor model described here has the capability to model the effects of friction, area change, and mass addition, in addition to the heat addition process. A comparison is made of the results from four cases: (1) heat addition only; (2) heat addition plus friction; (3) heat addition, friction, and area reduction, and (4) heat addition, friction, area reduction, and mass addition. The relative impact of these effects on the Mach number, static temperature, and static pressure distributions within the combustor are then shown. Finally, the effects of frozen versus equilibrium flow conditions within the exhaust plume is discussed.

9 CFR 424.1 - Purpose and scope.

Code of Federal Regulations, 2010 CFR

2010-01-01

... the preparation of meat and the processing of poultry products. The rules in this part further the... color additives) and sources of radiation that may render meat or poultry products adulterated or... REQUIREMENTS UNDER THE FEDERAL MEAT INSPECTION ACT AND THE POULTRY PRODUCTS INSPECTION ACT PREPARATION AND...

Engineered Osmosis for Energy Efficient Separations: Optimizing Waste Heat Utilization FINAL SCIENTIFIC REPORT DOE F 241.3

DOE Office of Scientific and Technical Information (OSTI.GOV)

NATHAN HANCOCK

2013-01-13

The purpose of this study is to design (i) a stripper system where heat is used to strip ammonia (NH{sub 3}) and carbon dioxide (CO{sub 2}) from a diluted draw solution; and (ii) a condensation or absorption system where the stripped NH{sub 3} and CO{sub 2} are captured in condensed water to form a re-concentrated draw solution. This study supports the Industrial Technologies Program of the DOE Office of Energy Efficiency and Renewable Energy and their Industrial Energy Efficiency Grand Challenge award solicitation. Results from this study show that stimulated Oasys draw solutions composed of a complex electrolyte solution associatedmore » with the dissolution of NH{sub 3} and CO{sub 2} gas in water can successfully be stripped and fully condensed under standard atmospheric pressure. Stripper bottoms NH{sub 3} concentration can reliably be reduced to < 1 mg/L, even when starting with liquids that have an NH{sub 3} mass fraction exceeding 6% to stimulate diluted draw solution from the forward osmosis membrane component of the process. Concentrated draw solution produced by fully condensing the stripper tops was show to exceed 6 M-C with nitrogen-to-carbon (N:C) molar ratios on the order of two. Reducing the operating pressure of the stripper column serves to reduce the partial vapor pressure of both NH{sub 3} and CO{sub 2} in solution and enables lower temperature operation towards integration of industrial low-grade of waste heat. Effective stripping of solutes was observed with operating pressures as low as 100 mbar (3-inHg). Systems operating at reduced pressure and temperature require additional design considerations to fully condense and absorb these constituents for reuse within the Oasys EO system context. Comparing empirical data with process stimulation models confirmed that several key parameters related to vapor-liquid equilibrium and intrinsic material properties were not accurate. Additional experiments and refinement of material property databases within the chosen process stimulation software was required to improve the reliability of process simulations for engineering design support. Data from experiments was also employed to calculate critical mass transfer and system design parameters (such as the height equivalent to a theoretical plate (HETP)) to aid in process design. When measured in a less than optimal design state for the stripping of NH{sub 3} and CO{sub 2} from a simulated dilute draw solution the HETP for one type of commercial stripper packing material was 1.88 ft/stage. During this study it was observed that the heat duty required to vaporize the draw solution solutes is substantially affected by the amount of water boilup also produced to achieve a low NH{sub 3} stripper bottoms concentration specification. Additionally, fluid loading of the stripper packing media is a critical performance parameter that affects all facets of optimum stripper column performance. Condensation of the draw solution tops vapor requires additional process considerations if being conducted in sub-atmospheric conditions and low temperature. Future work will focus on the commercialization of the Oasys EO technology platform for numerous applications in water and wastewater treatment as well as harvesting low enthalpy energy with our proprietary osmotic heat engine. Engineering design related to thermal integration of Oasys EO technology for both low and hig-grade heat applications is underway. Novel thermal recovery processes are also being investigated in addition to the conventional approaches described in this report. Oasys Water plans to deploy commercial scale systems into the energy and zero liquid discharge markets in 2013. Additional process refinement will lead to integration of low enthalpy renewable heat sources for municipal desalination applications.« less

Requirements Analysis Study for Master Pump Shutdown System Project Development Specification [SEC 1 and 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

BEVINS, R.R.

This study is a requirements document that presents analysis for the functional description for the master pump shutdown system. This document identifies the sources of the requirements and/or how these were derived. Each requirement is validated either by quoting the source or an analysis process involving the required functionality, performance characteristics, operations input or engineering judgment. The requirements in this study apply to the first phase of the W314 Project. This document has been updated during the definitive design portion of the first phase of the W314 Project to capture additional software requirements and is planned to be updated duringmore » the second phase of the W314 Project to cover the second phase of the project's scope.« less

Visualization of Computational Fluid Dynamics

NASA Technical Reports Server (NTRS)

Gerald-Yamasaki, Michael; Hultquist, Jeff; Bryson, Steve; Kenwright, David; Lane, David; Walatka, Pamela; Clucas, Jean; Watson, Velvin; Lasinski, T. A. (Technical Monitor)

1995-01-01

Scientific visualization serves the dual purpose of exploration and exposition of the results of numerical simulations of fluid flow. Along with the basic visualization process which transforms source data into images, there are four additional components to a complete visualization system: Source Data Processing, User Interface and Control, Presentation, and Information Management. The requirements imposed by the desired mode of operation (i.e. real-time, interactive, or batch) and the source data have their effect on each of these visualization system components. The special requirements imposed by the wide variety and size of the source data provided by the numerical simulation of fluid flow presents an enormous challenge to the visualization system designer. We describe the visualization system components including specific visualization techniques and how the mode of operation and source data requirements effect the construction of computational fluid dynamics visualization systems.

Vibrational sum frequency generation (SFG) spectroscopic study of crystalline cellulose in biomass

NASA Astrophysics Data System (ADS)

Kim, Seong H.; Lee, Christopher M.; Kafle, Kabindra; Park, Yong Bum; Xi, Xiaoning

2013-09-01

The noncentrosymmetry requirement of sum frequency generation (SFG) spectroscopy allows selective detection of crystalline cellulose in plant cell walls and lignocellulose biomass without spectral interferences from hemicelluloses and lignin. In addition, the phase synchronization requirement of the SFG process allows noninvasive investigation of spatial arrangement of crystalline cellulose microfibrils in the sample. This paper reviews how these principles are applied to reveal structural information of crystalline cellulose in plant cell walls and biomass.

Pilot Plant Testing of Hot Gas Building Decontamination Process

DTIC Science & Technology

1987-10-30

last hours of the cooldown (after water traps in the line were installed) showed no detectable contamination from this station. 1 60 CwC -So 0) 0 o j...Since we will not require refrigeration, additional generators probably 0 qlill not be required. Water is trucked to the site. Agent contaminated water ...surface. The gauze was handled by forceps during all of the sampling steps to prevent contamination after the solvent extraction clean-up of the gauze pads

Conveyorized Radio Frequency Cure of Epoxy Glass Composites.

DTIC Science & Technology

1980-05-01

a conveyorized radio frequency oven. The conveyorized radio frequency 20-kilowatt (90-100 megahertz) dielectric heater was de - designed and...Process were de - termined with reference to property requirements specified in Table three of 8MS-8-196A. Although the BM-8,196A relates to material...requirements of the 8MS and agree with the values contained in the 3M certifying report. De - tailed test results are presented as Appendix J. In addition

Development of a new generation of high-temperature composite materials

NASA Technical Reports Server (NTRS)

Brindley, P. K.

1990-01-01

Intermetallic matrix composites proposed to meet advanced aeropropulsion requirements are discussed. The powder metallurgy fabrication process currently being used to produce these intermetallic matrix composites will be presented, as will properties of one such composite, SiC/Ti3Al+Nb. In addition, the direction of future research will be outlined, including plans for enhanced fabrication of intermetallic composites by the arc-spray technique and fiber development by the floating-zone process.

Processes for producing polyhydroxybutyrate and related polyhydroxyalkanoates in the plastids of higher plants

DOEpatents

Somerville, Christopher R.; Nawrath, Christiane; Poirier, Yves

1997-03-11

The present invention relates to a process for producing poly-D-(-)-3-hydroxybutyric acid (PHB) and related polyhydroxyalkanoates (PHA) in the plastids of plants. The production of PHB is accomplished by genetically transforming plants with modified genes from microorganisms. The genes encode the enzymes required to synthesize PHB from acetyl-CoA or related metabolites and are fused with additional plant sequences for targeting the enzymes to the plastid.

Cross-coherent vector sensor processing for spatially distributed glider networks.

PubMed

Nichols, Brendan; Sabra, Karim G

2015-09-01

Autonomous underwater gliders fitted with vector sensors can be used as a spatially distributed sensor array to passively locate underwater sources. However, to date, the positional accuracy required for robust array processing (especially coherent processing) is not achievable using dead-reckoning while the gliders remain submerged. To obtain such accuracy, the gliders can be temporarily surfaced to allow for global positioning system contact, but the acoustically active sea surface introduces locally additional sensor noise. This letter demonstrates that cross-coherent array processing, which inherently mitigates the effects of local noise, outperforms traditional incoherent processing source localization methods for this spatially distributed vector sensor network.

Dental Arch Wire

NASA Technical Reports Server (NTRS)

1979-01-01

Straightening teeth is an arduous process requiring months, often years, of applying corrective pressure by means of arch wires-better known as brace-which may have to be changed several times in the course of treatment. A new method has been developed by Dr. George Andreasen, orthodontist and dental scientist at the University of Iowa. The key is a new type of arch wire material, called Nitinol, with exceptional elasticity which helps reduce the required number of brace changes. An alloy of nickel and titanium, Nitinol was originally developed for aerospace applications by the Naval Ordnance Laboratory, now the Naval Surface Weapons Laboratory, White Oaks, Maryland. NASA subsequently conducted additional research on the properties of Nitinol and on procedures for processing the metal.

Blind detection of giant pulses: GPU implementation

NASA Astrophysics Data System (ADS)

Ait-Allal, Dalal; Weber, Rodolphe; Dumez-Viou, Cédric; Cognard, Ismael; Theureau, Gilles

2012-01-01

Radio astronomical pulsar observations require specific instrumentation and dedicated signal processing to cope with the dispersion caused by the interstellar medium. Moreover, the quality of observations can be limited by radio frequency interference (RFI) generated by Telecommunications activity. This article presents the innovative pulsar instrumentation based on graphical processing units (GPU) which has been designed at the Nançay Radio Astronomical Observatory. In addition, for giant pulsar search, we propose a new approach which combines a hardware-efficient search method and some RFI mitigation capabilities. Although this approach is less sensitive than the classical approach, its advantage is that no a priori information on the pulsar parameters is required. The validation of a GPU implementation is under way.

HEVC real-time decoding

NASA Astrophysics Data System (ADS)

Bross, Benjamin; Alvarez-Mesa, Mauricio; George, Valeri; Chi, Chi Ching; Mayer, Tobias; Juurlink, Ben; Schierl, Thomas

2013-09-01

The new High Efficiency Video Coding Standard (HEVC) was finalized in January 2013. Compared to its predecessor H.264 / MPEG4-AVC, this new international standard is able to reduce the bitrate by 50% for the same subjective video quality. This paper investigates decoder optimizations that are needed to achieve HEVC real-time software decoding on a mobile processor. It is shown that HEVC real-time decoding up to high definition video is feasible using instruction extensions of the processor while decoding 4K ultra high definition video in real-time requires additional parallel processing. For parallel processing, a picture-level parallel approach has been chosen because it is generic and does not require bitstreams with special indication.

Sense and sensibility: flagellum-mediated gene regulation

PubMed Central

Anderson, Jennifer K.; Smith, Todd G.; Hoover, Timothy R.

2009-01-01

The flagellum, a rotary engine required for motility in many bacteria, plays key roles in gene expression. It has been known for some time that flagellar substructures serve as checkpoints that coordinate flagellar gene expression with assembly. Less well understood, however, are other more global effects on gene expression. For instance, the flagellum acts as a ‘wetness’ sensor in Salmonella typhimurium and as a mechanosensor in other bacteria. Additionally, it has been implicated in a variety of bacterial processes, including biofilm formation, pathogenesis and symbiosis. Although for many of these processes it may be simply that motility is required, for other cases it seems that the flagellum plays an underappreciated role in regulating gene expression. PMID:19942438

Sense and sensibility: flagellum-mediated gene regulation.

PubMed

Anderson, Jennifer K; Smith, Todd G; Hoover, Timothy R

2010-01-01

The flagellum, a rotary engine required for motility in many bacteria, plays key roles in gene expression. It has been known for some time that flagellar substructures serve as checkpoints that coordinate flagellar gene expression with assembly. Less well understood, however, are other more global effects on gene expression. For instance, the flagellum acts as a 'wetness' sensor in Salmonella typhimurium, and as a mechanosensor in other bacteria. Additionally, it has been implicated in a variety of bacterial processes, including biofilm formation, pathogenesis and symbiosis. Although for many of these processes it might be simply that motility is required, in other cases it seems that the flagellum plays an underappreciated role in regulating gene expression.

Laboratory formation of non-cementing, methane hydrate-bearing sands

USGS Publications Warehouse

Waite, William F.; Bratton, Peter M.; Mason, David H.

2011-01-01

Naturally occurring hydrate-bearing sands often behave as though methane hydrate is acting as a load-bearing member of the sediment. Mimicking this behavior in laboratory samples with methane hydrate likely requires forming hydrate from methane dissolved in water. To hasten this formation process, we initially form hydrate in a free-gas-limited system, then form additional hydrate by circulating methane-supersaturated water through the sample. Though the dissolved-phase formation process can theoretically be enhanced by increasing the pore pressure and flow rate and lowering the sample temperature, a more fundamental concern is preventing clogs resulting from inadvertent methane bubble formation in the circulation lines. Clog prevention requires careful temperature control throughout the circulation loop.

Atmospheric Capture On Mars (and Processing)

NASA Technical Reports Server (NTRS)

Muscatello, Tony

2017-01-01

The ultimate destination of NASA's human exploration program is Mars. In Situ Resource Utilization (ISRU) is a key technology required to enable such missions, as first proposed by Prof. Robert Ash in 1976. This presentation will review progress in the systems required to produce rocket propellant, oxygen, and other consumables on Mars using the carbon dioxide atmosphere and other potential resources. For many years, NASA, commercial companies, and academia have been developing, and demonstrating techniques to capture and purify Martian atmospheric gases for their utilization for the production of hydrocarbons, oxygen, and water in ISRU systems. Other gases will be required to be separated from Martian atmospheric gases to provide pure CO2 for processing elements. Significant progress has been demonstrated in CO2 collection via adsorption by molecular sieves, freezing, and direct compression. Early stage work in adsorption in Ionic Liquids followed by electrolysis to oxygen is also underway. In addition, other Martian gases, such as nitrogen and argon, occur in concentrations high enough to be useful as buffer gas and could be captured as well. Gas separation requirements include, but are not limited to the selective separation of: (1) methane and water from unreacted carbon oxides (CO2-CO) and hydrogen typical of a Sabatier-type process, (2) carbon oxides and water from unreacted hydrogen from a Reverse Water-Gas Shift process, and (3) carbon oxides from oxygen from a trash/waste processing reaction.

The NASA Commercial Crew Program (CCP) Mission Assurance Process

NASA Technical Reports Server (NTRS)

Canfield, Amy

2016-01-01

In 2010, NASA established the Commercial Crew Program in order to provide human access to the International Space Station and low earth orbit via the commercial (non-governmental) sector. A particular challenge to NASA has been how to determine the commercial providers transportation system complies with Programmatic safety requirements. The process used in this determination is the Safety Technical Review Board which reviews and approves provider submitted Hazard Reports. One significant product of the review is a set of hazard control verifications. In past NASA programs, 100 percent of these safety critical verifications were typically confirmed by NASA. The traditional Safety and Mission Assurance (SMA) model does not support the nature of the Commercial Crew Program. To that end, NASA SMA is implementing a Risk Based Assurance (RBA) process to determine which hazard control verifications require NASA authentication. Additionally, a Shared Assurance Model is also being developed to efficiently use the available resources to execute the verifications. This paper will describe the evolution of the CCP Mission Assurance process from the beginning of the Program to its current incarnation. Topics to be covered include a short history of the CCP; the development of the Programmatic mission assurance requirements; the current safety review process; a description of the RBA process and its products and ending with a description of the Shared Assurance Model.

Gamma radiation in the reduction of S almonella spp. inoculated on minimally processed watercress ( Nasturtium officinalis)

NASA Astrophysics Data System (ADS)

Martins, C. G.; Behrens, J. H.; Destro, M. T.; Franco, B. D. G. M.; Vizeu, D. M.; Hutzler, B.; Landgraf, M.

2004-09-01

Consumer attitudes towards foods have changed in the last two decades increasing requirements for freshlike products. Consequently, less extreme treatments or additives are being required. Minimally processed foods have freshlike characteristics and satisfy this new consumer demand. Besides freshness, the minimally processing also provide convenience required by the market. Salad vegetables can be source of pathogen such as Salmonella, Escherichia coli O157:H7, Shigella spp. The minimal processing does not reduce the levels of pathogenic microorganisms to safe levels. Therefore, this study was carried out in order to improve the microbiological safety and the shelf-life of minimally processed vegetables using gamma radiation. Minimally processed watercress inoculated with a cocktail of Salmonella spp was exposed to 0.0, 0.2, 0.5, 0.7, 1.0, 1.2 and 1.5 kGy. Irradiated samples were diluted 1:10 in saline peptone water and plated onto tryptic soy agar that were incubated at 37°C/24 h. D 10 values for Salmonella spp. inoculated in watercress varied from 0.29 to 0.43 kGy. Therefore, a dose of 1.7 kGy will reduce Salmonella population in watercress by 4 log 10. The shelf-life was increased by 1 {1}/{2} day when the product was exposed to 1 kGy.

The Role of Star Formation in Radio-Loud Galaxy Groups

NASA Astrophysics Data System (ADS)

Herbst, Hanna; Wilcots, E.; Hess, K.

2010-01-01

X-ray observations have shown that additional non-gravitational processes are required to explain the heating of the intergalactic medium in galaxy groups. The two most likely processes are galactic outflows from starbursts and feedback from AGN. Here, we look at star formation as a possible additional heating mechanism in X-ray luminous groups such as NGC 741, NGC 1052, NGC 524, and NGC 1587. We report on the results of optical imaging of these groups carried out using the WIYN 3.5m telescope with a specific emphasis on measuring the star formation rates of the resident galaxies in each group and estimating the impact of that star formation on the thermodynamics of the intragroup medium.

NASA's Applied Sciences: Natural Disasters Program

NASA Technical Reports Server (NTRS)

Kessler, Jason L.

2010-01-01

Fully utilize current and near-term airborne and spaceborne assets and capabilities. NASA spaceborne instruments are for research but can be applied to natural disaster response as appropriate. NASA airborne instruments can be targeted specifically for disaster response. Could impact research programs. Better flow of information improves disaster response. Catalog capability, product, applicable disaster, points of contact. Ownership needs to come from the highest level of NASA - unpredictable and irregular nature of disasters requires contingency funding for disaster response. Build-in transfer of applicable natural disaster research capabilities to operational functionality at other agencies (e.g., USFS, NOAA, FEMA...) at the outset, whenever possible. For the Decadal Survey Missions, opportunities exist to identify needs and requirements early in the mission design process. Need to understand additional needs and commitments for meeting the needs of the disaster community. Opportunity to maximize disaster response and mitigation from the Decadal Survey Missions. Additional needs or capabilities may require agency contributions.

The role of frit in nuclear waste vitrification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vienna, J.D.; Smith, P.A.; Dorn, D.A.

1994-04-01

Vitrification of nuclear waste requires additives which are often vitrified independently to form a frit. Frit composition is formulated to meet the needs of glass composition and processing. The effects of frit on melter feed and melt processing, glass acceptance, and waste loading is of practical interest in understanding the trade-offs associated with the competing demands placed on frit composition. Melter feed yield stress, viscosity and durability of frits and corresponding waste glasses as well as the kinetics of elementary melting processes have been measured. The results illustrate the competing requirements on frit. Four frits (FY91, FY93, HW39-4, and SR202)more » and simulated neutralized current acid waste (NCAW) were used in this study. The experimental evidence shows that optimization of frit for one processing related property often results in poorer performance for the remaining properties. The difficulties associated with maximum waste loading and durability are elucidated for glasses which could be processed using technology available for the previously proposed Hanford Waste Vitrification Plant.« less

Investigation on the Flexural Creep Stiffness Behavior of PC-ABS Material Processed by Fused Deposition Modeling Using Response Surface Definitive Screening Design

NASA Astrophysics Data System (ADS)

Mohamed, Omar Ahmed; Masood, Syed Hasan; Bhowmik, Jahar Lal

2017-03-01

The resistance of polymeric materials to time-dependent plastic deformation is an important requirement of the fused deposition modeling (FDM) design process, its processed products, and their application for long-term loading, durability, and reliability. The creep performance of the material and part processed by FDM is the fundamental criterion for many applications with strict dimensional stability requirements, including medical implants, electrical and electronic products, and various automotive applications. Herein, the effect of FDM fabrication conditions on the flexural creep stiffness behavior of polycarbonate-acrylonitrile-butadiene-styrene processed parts was investigated. A relatively new class of experimental design called "definitive screening design" was adopted for this investigation. The effects of process variables on flexural creep stiffness behavior were monitored, and the best suited quadratic polynomial model with high coefficient of determination ( R 2) value was developed. This study highlights the value of response surface definitive screening design in optimizing properties for the products and materials, and it demonstrates its role and potential application in material processing and additive manufacturing.

NANEX: Process design and optimization.

PubMed

Baumgartner, Ramona; Matić, Josip; Schrank, Simone; Laske, Stephan; Khinast, Johannes; Roblegg, Eva

2016-06-15

Previously, we introduced a one-step nano-extrusion (NANEX) process for transferring aqueous nano-suspensions into solid formulations directly in the liquid phase. Nano-suspensions were fed into molten polymers via a side-feeding device and excess water was eliminated via devolatilization. However, the drug content in nano-suspensions is restricted to 30 % (w/w), and obtaining sufficiently high drug loadings in the final formulation requires the processing of high water amounts and thus a fundamental process understanding. To this end, we investigated four polymers with different physicochemical characteristics (Kollidon(®) VA64, Eudragit(®) E PO, HPMCAS and PEG 20000) in terms of their maximum water uptake/removal capacity. Process parameters as throughput and screw speed were adapted and their effect on the mean residence time and filling degree was studied. Additionally, one-dimensional discretization modeling was performed to examine the complex interactions between the screw geometry and the process parameters during water addition/removal. It was established that polymers with a certain water miscibility/solubility can be manufactured via NANEX. Long residence times of the molten polymer in the extruder and low filling degrees in the degassing zone favored the addition/removal of significant amounts of water. The residual moisture content in the final extrudates was comparable to that of extrudates manufactured without water. Copyright © 2016 Elsevier B.V. All rights reserved.

Operations management system advanced automation: Fault detection isolation and recovery prototyping

NASA Technical Reports Server (NTRS)

Hanson, Matt

1990-01-01

The purpose of this project is to address the global fault detection, isolation and recovery (FDIR) requirements for Operation's Management System (OMS) automation within the Space Station Freedom program. This shall be accomplished by developing a selected FDIR prototype for the Space Station Freedom distributed processing systems. The prototype shall be based on advanced automation methodologies in addition to traditional software methods to meet the requirements for automation. A secondary objective is to expand the scope of the prototyping to encompass multiple aspects of station-wide fault management (SWFM) as discussed in OMS requirements documentation.

Materials for helicopter gears

NASA Technical Reports Server (NTRS)

1979-01-01

Some of the power train transmission gears in helicopter drive systems can become critical components as performance requirements are increased; accordingly, increasing attention must be paid to new alloys in order to obtain required performance reliability and survivability. Candidate advanced alloys, with improved high temperature properties, while increasing the resistance to scoring and scuffing, tend to have lower ductility and fracture toughness. An attempt is made to identify design materials, and process problems and requirements. In addition, it is recommended that the characterization of candidate steels be accelerated; preliminary investigation indicates that new alloys may provide improved capability against surface distress.

75 FR 64394 - Buy America Waiver Notification

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-19

... The FHWA's Buy America policy in 23 CFR 635.410 requires a domestic manufacturing process for any... opposed the approval of the waiver request. The PennDOT contacted the potential domestic manufactures Berg... production run. During the 15-day comment period, the FHWA conducted additional nationwide review to locate...

Intelligence-Driven Border Security: A Promethean View of U.S. Border Patrol Intelligence Operations

DTIC Science & Technology

2015-12-01

USBP agent, intelligence ( BPA -I), information sharing, capability gap analysis process (CGAP), Tucson Sector Red Team 15. NUMBER OF PAGES 109 16...27 2. BPA -I .............................................................................................28 3. BPA -I Requirements...71 APPENDIX A. PROFESSIONAL INTELLIGENCE ASSOCIATIONS— ADDITIONAL OPPORTUNITIES FOR BPA -IS

77 FR 43567 - Medical Area Body Network

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-25

... document requests comment on a number of issues related to the designation of Medical Body Area Network... also determined that additional notice and comment was required on key aspects related to the process and criteria for designating an MBAN coordinator. DATES: Comments must be filed on or before September...

Processes to improve energy efficiency during pumping and aeration of recirculating water in circular tank systems

USDA-ARS?s Scientific Manuscript database

Conventional gas transfer technologies for aquaculture systems occupy a large amount of space, require considerable capital investment, and can contribute to high electricity demand. In addition, diffused aeration in a circular tank can interfere with the hydrodynamics of water rotation and the spee...

Laboratory Accreditation Bureau (L-A-B)

DTIC Science & Technology

2011-03-28

to all Technical Advisors. Must agree with code of conduct, confidentiality and our mission DoD ELAP Program  ISO / IEC 17025 :2005 and DoD QSM...Additional DoD QSM requirements fit well in current 17025 process … just much, much more. Sector Specific. Outcome (L-A-B case)  83

28 CFR 100.16 - Cost estimate submission.

Code of Federal Regulations, 2013 CFR

2013-07-01

... evaluation of the estimated costs. The FBI reserves the right to request additional cost data from carriers... if, as determined by the FBI, all cost data reasonably available to the carrier are either submitted... explain the estimating process are required by the FBI and the carrier refuses to provide necessary data...

28 CFR 100.16 - Cost estimate submission.

Code of Federal Regulations, 2011 CFR

2011-07-01

... evaluation of the estimated costs. The FBI reserves the right to request additional cost data from carriers... if, as determined by the FBI, all cost data reasonably available to the carrier are either submitted... explain the estimating process are required by the FBI and the carrier refuses to provide necessary data...

28 CFR 100.16 - Cost estimate submission.

Code of Federal Regulations, 2012 CFR

2012-07-01

... evaluation of the estimated costs. The FBI reserves the right to request additional cost data from carriers... if, as determined by the FBI, all cost data reasonably available to the carrier are either submitted... explain the estimating process are required by the FBI and the carrier refuses to provide necessary data...

28 CFR 100.16 - Cost estimate submission.

Code of Federal Regulations, 2014 CFR

2014-07-01

... evaluation of the estimated costs. The FBI reserves the right to request additional cost data from carriers... if, as determined by the FBI, all cost data reasonably available to the carrier are either submitted... explain the estimating process are required by the FBI and the carrier refuses to provide necessary data...

An Entrepreneurial Approach to Project-Based Courses

ERIC Educational Resources Information Center

Pilskalns, Orest

2009-01-01

A senior project course is often employed to expose students to industrial problems and teamwork. Students are expected to use industrial strength tools to deal with issues such as requirements, design, process models, collaboration, management, testing, maintenance and more. In addition, the senior project often plays a large role in satisfying…

24 CFR 7.33 - Contents of the complaint.

Code of Federal Regulations, 2010 CFR

2010-04-01

... is a group of employees, former employees or applicants for employment who, it is alleged, have been... discriminates against the group on the basis of their common race, color, religion, sex, national origin, age... counseling process in 29 CFR 1614.105, no additional counseling is required. Class certification shall be...

77 FR 59998 - Self-Regulatory Organizations; The Options Clearing Corporation; Advance Notice Relating to the...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-01

... System for Theoretical Analysis and Numerical Simulations (``STANS''). STANS calculates margin with...'' simulations designed to measure the additional asset value required in any portfolio to eliminate an... Commission process and review your comments more efficiently, please use only one method. The Commission will...

42 CFR 495.370 - Appeals process for a Medicaid provider receiving electronic health record incentive payments.

Code of Federal Regulations, 2010 CFR

2010-10-01

... & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) STANDARDS AND CERTIFICATION STANDARDS FOR THE ELECTRONIC HEALTH RECORD TECHNOLOGY INCENTIVE PROGRAM Requirements Specific to the... provide that the provider (whether individual or entity) is also given any additional appeals rights that...

Young Children's Drawings in Problem Solving

ERIC Educational Resources Information Center

Bakar, Kamariah Abu; Way, Jennifer; Bobis, Janette

2016-01-01

This paper explores young children's drawings (6 years old) in early number and addition activities in Malaysia. Observation, informal interviews and analysis of drawings revealed two types of drawing, and gave insight into the transitional process required for children to utilise drawings in problem solving. We argue the importance of valuing and…

A Hydrothermal Origin for the Sulfate-rich Ocean of Europa

NASA Technical Reports Server (NTRS)

Zolotov, M. Yu.; Shock, E. L.

2001-01-01

Thermodynamic calculations show that formation of a sulfate-rich ocean on Europa might require high-temperature alkaline hydrothermal processes in the oxidized silicate mantle. The ocean on Europa could be thought of as a cooled hydrothermal fluid. Additional information is contained in the original extended abstract.

Teacher Perceptions of the Effectiveness of the Response to Intervention (RTI) Process

ERIC Educational Resources Information Center

Anderson, Yarby

2017-01-01

With federal education mandates and new developments highlighting academic failures, additional stress has been placed on teachers and administrators to provide interventions to a student's specific deficit areas. Now, general education teachers are required to use research-based interventions to eliminate the decline in academic success. The…

21 CFR 179.26 - Ionizing radiation for the treatment of food.

Code of Federal Regulations, 2012 CFR

2012-04-01

... SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) IRRADIATION IN THE PRODUCTION, PROCESSING AND... “Treated by irradiation” in addition to information required by other regulations. The logo shall be placed... statement that discloses that a food has been intentionally subject to irradiation. (2) For irradiated foods...

21 CFR 179.26 - Ionizing radiation for the treatment of food.

Code of Federal Regulations, 2010 CFR

2010-04-01

... SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) IRRADIATION IN THE PRODUCTION, PROCESSING AND... “Treated by irradiation” in addition to information required by other regulations. The logo shall be placed... statement that discloses that a food has been intentionally subject to irradiation. (2) For irradiated foods...

21 CFR 179.26 - Ionizing radiation for the treatment of food.

Code of Federal Regulations, 2011 CFR

2011-04-01

... SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) IRRADIATION IN THE PRODUCTION, PROCESSING AND... “Treated by irradiation” in addition to information required by other regulations. The logo shall be placed... statement that discloses that a food has been intentionally subject to irradiation. (2) For irradiated foods...

21 CFR 179.26 - Ionizing radiation for the treatment of food.

Code of Federal Regulations, 2013 CFR

2013-04-01

... SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) IRRADIATION IN THE PRODUCTION, PROCESSING AND... “Treated by irradiation” in addition to information required by other regulations. The logo shall be placed... statement that discloses that a food has been intentionally subject to irradiation. (2) For irradiated foods...

Defining and Developing Curricula in the Context of Cooperative Extension

ERIC Educational Resources Information Center

Smith, Martin H.; Worker, Steven M.; Meehan, Cheryl L.; Schmitt-McQuitty, Lynn; Ambrose, Andrea; Brian, Kelley; Schoenfelder, Emily

2017-01-01

Effective curricula are considered to be the cornerstone of successful programming in Extension. However, there is no universal operationalized definition of the term "curriculum" as it applies to Extension. Additionally, the development of curricula requires a systematic process that takes into account numerous factors. We provide an…

21 CFR 179.26 - Ionizing radiation for the treatment of food.

Code of Federal Regulations, 2014 CFR

2014-04-01

... SERVICES (CONTINUED) IRRADIATION IN THE PRODUCTION, PROCESSING AND HANDLING OF FOOD Radiation and Radiation... irradiation” in addition to information required by other regulations. The logo shall be placed prominently... that discloses that a food has been intentionally subject to irradiation. (2) For irradiated foods not...

Dietary Micronutrients Promote Neuronal Differentiation by Modulating the Mitochondrial-Nuclear Dialogue.

PubMed

Xie, Kui; Sheppard, Allan

2018-07-01

The metabolic requirements of differentiated neurons are significantly different from that of neuronal precursor and neural stem cells. While a re-programming of metabolism is tightly coupled to the neuronal differentiation process, whether shifts in mitochondrial mass, glycolysis, and oxidative phosphorylation are required (or merely consequential) in differentiation is not yet certain. In addition to providing more energy, enhanced metabolism facilitates differentiation by supporting increased neurotransmitter signaling and underpinning epigenetic regulation of gene expression. Both epidemiological and animal studies demonstrate that micronutrients (MNs) significantly influence many aspects of neonatal brain development, particularly neural migration and survival, neurite outgrowth, and process maturation. Here we review recent insights into the importance of metabolic reprogramming in neuronal differentiation, before considering evidence that micronutrient signaling may be key to regulating these processes. © 2018 WILEY Periodicals, Inc.

Additive Manufacturing Consolidation of Low-Cost Water Atomized Steel Powder Using Micro-Induction Sintering

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carter, William G.; Rios, Orlando; U

ORNL worked with Grid Logic Inc to demonstrate micro induction sintering (MIS) and binder decomposition of steel powders. It was shown that MIS effectively emits spatially confined electromagnetic energy that is directly coupled to metallic powders resulting in resistive heating of individual particles. The non-uniformity of particle morphology and distribution of the water atomized steel powders resulted in inefficient transfer of energy. It was shown that adhering the particles together using polymer binders resulted in more efficient coupling. Using the MIS processes, debinding and sintering could be done in a single step. When combined with another system, such as binder-jet,more » this could reduce the amount of required post-processing. An invention disclosure was filed on hybrid systems that use MIS to reduce the amount of required post-processing.« less

Use of a modified informed consent process among vulnerable patients: a descriptive study.

PubMed

Sudore, Rebecca L; Landefeld, C Seth; Williams, Brie A; Barnes, Deborah E; Lindquist, Karla; Schillinger, Dean

2006-08-01

Little is known about patient characteristics associated with comprehension of consent information, and whether modifications to the consent process can promote understanding. To describe a modified research consent process, and determine whether literacy and demographic characteristics are associated with understanding consent information. Descriptive study of a modified consent process: consent form (written at a sixth-grade level) read to participants, combined with 7 comprehension questions and targeted education, repeated until comprehension achieved (teach-to-goal). Two hundred and four ethnically diverse subjects, aged > or = 50, consenting for a trial to improve the forms used for advance directives. Number of passes through the consent process required to achieve complete comprehension. Literacy assessed in English and Spanish with the Short Form Test of Functional Health Literacy in Adults (scores 0 to 36). Participants had a mean age of 61 years and 40% had limited literacy (s-TOHFLA<23). Only 28% of subjects answered all comprehension questions correctly on the first pass. After adjustment, lower literacy (P=.04) and being black (P=.03) were associated with requiring more passes through the consent process. Not speaking English as a primary language was associated with requiring more passes through the consent process in bivariate analyses (P<.01), but not in multivariable analyses (P>.05). After the second pass, most subjects (80%) answered all questions correctly. With a teach-to-goal strategy, 98% of participants who engaged in the consent process achieved complete comprehension. Lower literacy and minority status are important determinants of understanding consent information. Using a modified consent process, little additional education was required to achieve complete comprehension, regardless of literacy or language barriers.

From Data to Knowledge: GEOSS experience and the GEOSS Knowledge Base contribution to the GCI

NASA Astrophysics Data System (ADS)

Santoro, M.; Nativi, S.; Mazzetti, P., Sr.; Plag, H. P.

2016-12-01

According to systems theory, data is raw, it simply exists and has no significance beyond its existence; while, information is data that has been given meaning by way of relational connection. The appropriate collection of information, such that it contributes to understanding, is a process of knowledge creation.The Global Earth Observation System of Systems (GEOSS) developed by the Group on Earth Observations (GEO) is a set of coordinated, independent Earth observation, information and processing systems that interact and provide access to diverse information for a broad range of users in both public and private sectors. GEOSS links these systems to strengthen the monitoring of the state of the Earth. In the past ten years, the development of GEOSS has taught several lessons dealing with the need to move from (open) data to information and knowledge sharing. Advanced user-focused services require to move from a data-driven framework to a knowledge sharing platform. Such a platform needs to manage information and knowledge, in addition to datasets linked to them. For this scope, GEO has launched a specific task called "GEOSS Knowledge Base", which deals with resources, like user requirements, Sustainable Development Goals (SDGs), observation and processing ontologies, publications, guidelines, best practices, business processes/algorithms, definition of advanced concepts like Essential Variables (EVs), indicators, strategic goals, etc. In turn, information and knowledge (e.g. guidelines, best practices, user requirements, business processes, algorithms, etc.) can be used to generate additional information and knowledge from shared datasets. To fully utilize and leverage the GEOSS Knowledge Base, the current GEOSS Common Infrastructure (GCI) model will be extended and advanced to consider important concepts and implementation artifacts, such as data processing services and environmental/economic models as well as EVs, Primary Indicators, and SDGs. The new GCI model will link these concepts to the present dataset, observation and sensor concepts, enabling a set of very important new capabilities to be offered to GEOSS users.

Validating the Use of Deep Learning Neural Networks for Correction of Large Hydrometric Datasets

NASA Astrophysics Data System (ADS)

Frazier, N.; Ogden, F. L.; Regina, J. A.; Cheng, Y.

2017-12-01

Collection and validation of Earth systems data can be time consuming and labor intensive. In particular, high resolution hydrometric data, including rainfall and streamflow measurements, are difficult to obtain due to a multitude of complicating factors. Measurement equipment is subject to clogs, environmental disturbances, and sensor drift. Manual intervention is typically required to identify, correct, and validate these data. Weirs can become clogged and the pressure transducer may float or drift over time. We typically employ a graphical tool called Time Series Editor to manually remove clogs and sensor drift from the data. However, this process is highly subjective and requires hydrological expertise. Two different people may produce two different data sets. To use this data for scientific discovery and model validation, a more consistent method is needed to processes this field data. Deep learning neural networks have proved to be excellent mechanisms for recognizing patterns in data. We explore the use of Recurrent Neural Networks (RNN) to capture the patterns in the data over time using various gating mechanisms (LSTM and GRU), network architectures, and hyper-parameters to build an automated data correction model. We also explore the required amount of manually corrected training data required to train the network for reasonable accuracy. The benefits of this approach are that the time to process a data set is significantly reduced, and the results are 100% reproducible after training is complete. Additionally, we train the RNN and calibrate a physically-based hydrological model against the same portion of data. Both the RNN and the model are applied to the remaining data using a split-sample methodology. Performance of the machine learning is evaluated for plausibility by comparing with the output of the hydrological model, and this analysis identifies potential periods where additional investigation is warranted.

Effects of local institutional review board review on participation in national practice-based research network studies.

PubMed

Finch, Stacia A; Barkin, Shari L; Wasserman, Richard C; Dhepyasuwan, Niramol; Slora, Eric J; Sege, Robert D

2009-12-01

To describe the process and outcomes of local institutional review board (IRB) review for 2 Pediatric Research in Office Settings (PROS) studies. Pediatric Research in Office Settings conducted 2 national studies concerning sensitive topics: (1) Child Abuse Recognition Experience Study (CARES), an observational study of physician decision making, and (2) Safety Check, a violence prevention intervention trial. Institutional review board approval was secured by investigators' sites, the American Academy of Pediatrics, and practices with local IRBs. Practices were queried about IRB rules at PROS enrollment and study recruitment. Pediatric Research in Office Settings practices in 29 states. Eighty-eight PROS practices (75 IRBs). Main Exposure Local IRB presence. Local IRB presence, level of PROS assistance, IRB process, study participation, data collection completion, and minority enrollment. Practices requiring additional local IRB approval agreed to participate less than those that did not (CARES: 33% vs 52%; Safety Check: 41% vs 56%). Of the 88 practices requiring local IRB approval, 55 received approval, with nearly 50% needing active PROS help, many requiring consent changes (eg, contact name additions, local IRB approval stamps), and 87% beginning data collection. Median days to obtain approval were 81 (CARES) and 109 (Safety Check). Practices requiring local IRB approval were less likely to complete data collection but more likely to enroll minority patients. Local IRB review was associated with lower participation rates, substantial effort navigating the process (with approval universally granted without substantive changes), and data collection delays. When considering future reforms, the national human subject protections system should consider the potential redundancy and effect on generalizability, particularly regarding enrollment of poor urban children, related to local IRB review.

Towards Using Reo for Compliance-Aware Business Process Modeling

NASA Astrophysics Data System (ADS)

Arbab, Farhad; Kokash, Natallia; Meng, Sun

Business process modeling and implementation of process supporting infrastructures are two challenging tasks that are not fully aligned. On the one hand, languages such as Business Process Modeling Notation (BPMN) exist to capture business processes at the level of domain analysis. On the other hand, programming paradigms and technologies such as Service-Oriented Computing (SOC) and web services have emerged to simplify the development of distributed web systems that underly business processes. BPMN is the most recognized language for specifying process workflows at the early design steps. However, it is rather declarative and may lead to the executable models which are incomplete or semantically erroneous. Therefore, an approach for expressing and analyzing BPMN models in a formal setting is required. In this paper we describe how BPMN diagrams can be represented by means of a semantically precise channel-based coordination language called Reo which admits formal analysis using model checking and bisimulation techniques. Moreover, since additional requirements may come from various regulatory/legislative documents, we discuss the opportunities offered by Reo and its mathematical abstractions for expressing process-related constraints such as Quality of Service (QoS) or time-aware conditions on process states.

Adaptation of the Haloarcula hispanica CRISPR-Cas system to a purified virus strictly requires a priming process

PubMed Central

Li, Ming; Wang, Rui; Zhao, Dahe; Xiang, Hua

2014-01-01

The clustered regularly interspaced short palindromic repeat (CRISPR)-Cas system mediates adaptive immunity against foreign nucleic acids in prokaryotes. However, efficient adaptation of a native CRISPR to purified viruses has only been observed for the type II-A system from a Streptococcus thermophilus industry strain, and rarely reported for laboratory strains. Here, we provide a second native system showing efficient adaptation. Infected by a newly isolated virus HHPV-2, Haloarcula hispanica type I-B CRISPR system acquired spacers discriminatively from viral sequences. Unexpectedly, in addition to Cas1, Cas2 and Cas4, this process also requires Cas3 and at least partial Cascade proteins, which are involved in interference and/or CRISPR RNA maturation. Intriguingly, a preexisting spacer partially matching a viral sequence is also required, and spacer acquisition from upstream and downstream sequences of its target sequence (i.e. priming protospacer) shows different strand bias. These evidences strongly indicate that adaptation in this system strictly requires a priming process. This requirement, if validated also true for other CRISPR systems as implied by our bioinformatic analysis, may help to explain failures to observe efficient adaptation to purified viruses in many laboratory strains, and the discrimination mechanism at the adaptation level that has confused scientists for years. PMID:24265226

Implementation of a formulary management process.

PubMed

Karel, Lauren I; Delisle, Dennis R; Anagnostis, Ellena A; Wordell, Cindy J

2017-08-15

The application of lean methodology in an initiative to redesign the formulary maintenance process at an academic medical center is described. Maintaining a hospital formulary requires clear communication and coordination among multiple members of the pharmacy department. Using principles of lean methodology, pharmacy department personnel within a multihospital health system launched a multifaceted initiative to optimize formulary management systemwide. The ongoing initiative began with creation of a formulary maintenance redesign committee consisting of pharmacy department personnel with expertise in informatics, automation, purchasing, drug information, and clinical pharmacy services. The committee met regularly and used lean methodology to design a standardized process for management of formulary additions and deletions and changes to medications' formulary status. Through value stream analysis, opportunities for process and performance improvement were identified; staff suggestions on process streamlining were gathered during a series of departmental kaizen events. A standardized template for development and dissemination of monographs associated with formulary additions and status changes was created. In addition, a shared Web-based checklist was developed to facilitate information sharing and timely initiation and completion of tasks involved in formulary status changes, and a permanent formulary maintenance committee was established to monitor and refine the formulary management process. A clearly defined, standardized process within the pharmacy department was developed for tracking necessary steps in enacting formulary changes to encourage safe and efficient workflow. Copyright © 2017 by the American Society of Health-System Pharmacists, Inc. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lingenfelter, A. C., LLNL

Materials for gas turbine engines are required to meet a wide range of temperature and stress application requirements. These alloys exhibit a combination of creep resistance, creep rupture strength, yield and tensile strength over a wide temperature range, resistance to environmental attack (including oxidation, nitridation, sulphidation and carburization), fatigue and thermal fatigue resistance, metallurgical stability and useful thermal expansion characteristics. These properties are exhibited by a series of solid-solution-strengthened and precipitation-hardened nickel, iron and cobalt alloys. The properties needed to meet the turbine engine requirements have been achieved by specific alloy additions, by heat treatment and by thermal mechanical processing.more » A thorough understanding of the metallurgy and metallurgical processing of these materials is imperative in order to successfully fusion weld them. This same basic understanding is required for repair of a component with the added dimension of the potential effects of thermal cycling and environmental exposure the component will have endured in service. This article will explore the potential problems in joining and repair welding these materials.« less

Requirements and Architecture Specification of the Joint Multi-Role (JMR) Joint Common Architecture (JCA) Demonstration System

DTIC Science & Technology

2015-12-01

response time re- quirements and in additional calibration requirements for DCFM that may create unexpected la - tency and latency jitter that can...manage the flight path of the aircraft. For more information about sensor correlation and fusion processes, the Air University New World Vistas ...request/reply actions. We specify its la - tency as a minimum and maximum of 300 ms.  SADataServiceProtocol: an abstraction of the SA data service as a

Removal of phosphate from greenhouse wastewater using hydrated lime.

PubMed

Dunets, C Siobhan; Zheng, Youbin

2014-01-01

Phosphate (P) contamination in nutrient-laden wastewater is currently a major topic of discussion in the North American greenhouse industry. Precipitation of P as calcium phosphate minerals using hydrated lime could provide a simple, inexpensive method for retrieval. A combination of batch experiments and chemical equilibrium modelling was used to confirm the viability of this P removal method and determine lime addition rates and pH requirements for greenhouse wastewater of varying nutrient compositions. Lime: P ratio (molar ratio of CaMg(OH)₄: PO₄‒P) provided a consistent parameter for estimating lime addition requirements regardless of initial P concentration, with a ratio of 1.5 providing around 99% removal of dissolved P. Optimal P removal occurred when lime addition increased the pH from 8.6 to 9.0, suggesting that pH monitoring during the P removal process could provide a simple method for ensuring consistent adherence to P removal standards. A Visual MINTEQ model, validated using experimental data, provided a means of predicting lime addition and pH requirements as influenced by changes in other parameters of the lime-wastewater system (e.g. calcium concentration, temperature, and initial wastewater pH). Hydrated lime addition did not contribute to the removal of macronutrient elements such as nitrate and ammonium, but did decrease the concentration of some micronutrients. This study provides basic guidance for greenhouse operators to use hydrated lime for phosphate removal from greenhouse wastewater.

NMSBA ? RS21.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kinnan, Mark K.; Valerio, Richard Arthur; Flanagan, Tatiana Paz

2016-12-01

This report gives introductory guidance on the level of effort required to create a data warehouse for mining data. Numerous tutorials have been provided to demonstrate the process of downloading raw data, processing the raw data, and importing the data into a PostgreSQL database. Additional information and tutorial has been provided on setting up a Hadoop cluster for storing vasts amounts of data. This report has been generated as a deliverable for a New Mexico Small Business Assistance (NMSBA) project.

Evaluation of ERDA-sponsored coal feed system development

NASA Technical Reports Server (NTRS)

Phen, R. L.; Luckow, W. K.; Mattson, L.; Otth, D.; Tsou, P.

1977-01-01

Coal feeders were evaluated based upon criteria such as technical feasibility, performance (i.e. ability to meet process requirements), projected life cycle costs, and projected development cost. An initial set of feeders was selected based on the feeders' cost savings potential compared with baseline lockhopper systems. Additional feeders were considered for selection based on: (1) increasing the probability of successful feeder development; (2) application to specific processes; and (3) technical merit. A coal feeder development program is outlined.

Processes for producing polyhydroxybutyrate and related polyhydroxyalkanoates in the plastids of higher plants

DOEpatents

Somerville, C.R.; Nawrath, C.; Poirier, Y.

1997-03-11

The present invention relates to a process for producing poly-D-(-)-3-hydroxybutyric acid (PHB) and related polyhydroxyalkanoates (PHA) in the plastids of plants. The production of PHB is accomplished by genetically transforming plants with modified genes from microorganisms. The genes encode the enzymes required to synthesize PHB from acetyl-CoA or related metabolites and are fused with additional plant sequences for targeting the enzymes to the plastid. 37 figs.

A calcium-channel homologue required for adaptation to dopamine and serotonin in Caenorhabditis elegans.

PubMed

Schafer, W R; Kenyon, C J

1995-05-04

Processing and storage of information by the nervous system requires the ability to modulate the response of excitable cells to neurotransmitter. A simple process of this type, known as adaptation or desensitization, occurs when prolonged stimulation triggers processes that attenuate the response to neurotransmitter. Here we report that the Caenorhabditis elegans gene unc-2 is required for adaptation to two neurotransmitters, dopamine and serotonin. A loss-of-function mutation in unc-2 resulted in failure to adapt either to paralysis by dopamine or to stimulation of egg laying by serotonin. In addition, unc-2 mutants displayed behaviours similar to those induced by serotonin treatment. We found that unc-2 encodes a homologue of a voltage-sensitive calcium-channel alpha-1 subunit. Expression of unc-2 occurs in two types of neurons implicated in the control of egg laying, a behaviour regulated by serotonin. Unc-2 appears to be required in modulatory neurons to downregulate the response of the egg-laying muscles to serotonin. We propose that adaptation to serotonin occurs through activation of an Unc-2-dependent calcium influx, which modulates the postsynaptic response to serotonin, perhaps by inhibiting the release of a potentiating neuropeptide.

Hydroxyl carboxylate based non-phosphorus corrosion inhibition process for reclaimed water pipeline and downstream recirculating cooling water system.

PubMed

Wang, Jun; Wang, Dong; Hou, Deyin

2016-01-01

A combined process was developed to inhibit the corrosion both in the pipeline of reclaimed water supplies (PRWS) and in downstream recirculating cooling water systems (RCWS) using the reclaimed water as makeup. Hydroxyl carboxylate-based corrosion inhibitors (e.g., gluconate, citrate, tartrate) and zinc sulfate heptahydrate, which provided Zn(2+) as a synergistic corrosion inhibition additive, were added prior to the PRWS when the phosphate (which could be utilized as a corrosion inhibitor) content in the reclaimed water was below 1.7 mg/L, and no additional corrosion inhibitors were required for the downstream RCWS. Satisfactory corrosion inhibition was achieved even if the RCWS was operated under the condition of high numbers of concentration cycles. The corrosion inhibition requirement was also met by the appropriate combination of PO4(3-) and Zn(2+) when the phosphate content in the reclaimed water was more than 1.7 mg/L. The process integrated not only water reclamation and reuse, and the operation of a highly concentrated RCWS, but also the comprehensive utilization of phosphate in reclaimed water and the application of non-phosphorus corrosion inhibitors. The proposed process reduced the operating cost of the PRWS and the RCWS, and lowered the environmental hazard caused by the excessive discharge of phosphate. Furthermore, larger amounts of water resources could be conserved as a result. Copyright © 2015. Published by Elsevier B.V.

Comprehensive and Highly Accurate Measurements of Crane Runways, Profiles and Fastenings

PubMed Central

Dennig, Dirk; Bureick, Johannes; Link, Johannes; Diener, Dmitri; Hesse, Christian; Neumann, Ingo

2017-01-01

The process of surveying crane runways has been continually refined due to the competitive situation, modern surveying instruments, additional sensors, accessories and evaluation procedures. Guidelines, such as the International Organization for Standardization (ISO) 12488-1, define target values that must be determined by survey. For a crane runway these are for example the span, the position and height of the rails. The process has to be objective and reproducible. However, common processes of surveying crane runways do not meet these requirements sufficiently. The evaluation of the protocols, ideally by an expert, requires many years of experience. Additionally, the recording of crucial parameters, e.g., the wear of the rail, or the condition of the rail fastening and rail joints, is not regulated and for that reason are often not considered during the measurement. To solve this deficit the Advanced Rail Track Inspection System (ARTIS) was developed. ARTIS is used to measure the 3D position of crane rails, the cross-section of the crane rails, joints and, for the first time, the (crane-rail) fastenings. The system consists of a monitoring vehicle and an external tracking sensor. It makes kinematic observations with the tracking sensor from outside the rail run, e.g., the floor of an overhead crane runway, possible. In this paper we present stages of the development process of ARTIS, new target values, calibration of sensors and results of a test measurement. PMID:28505076

An aspect-oriented approach for designing safety-critical systems

NASA Astrophysics Data System (ADS)

Petrov, Z.; Zaykov, P. G.; Cardoso, J. P.; Coutinho, J. G. F.; Diniz, P. C.; Luk, W.

The development of avionics systems is typically a tedious and cumbersome process. In addition to the required functions, developers must consider various and often conflicting non-functional requirements such as safety, performance, and energy efficiency. Certainly, an integrated approach with a seamless design flow that is capable of requirements modelling and supporting refinement down to an actual implementation in a traceable way, may lead to a significant acceleration of development cycles. This paper presents an aspect-oriented approach supported by a tool chain that deals with functional and non-functional requirements in an integrated manner. It also discusses how the approach can be applied to development of safety-critical systems and provides experimental results.

Microstructure and Corrosion Resistance of Laser Additively Manufactured 316L Stainless Steel

NASA Astrophysics Data System (ADS)

Trelewicz, Jason R.; Halada, Gary P.; Donaldson, Olivia K.; Manogharan, Guha

2016-03-01

Additive manufacturing (AM) of metal alloys to produce complex part designs via powder bed fusion methods such as laser melting promises to be a transformative technology for advanced materials processing. However, effective implementation of AM processes requires a clear understanding of the processing-structure-properties-performance relationships in fabricated components. In this study, we report on the formation of micro and nanoscale structures in 316L stainless steel samples printed by laser AM and their implications for general corrosion resistance. A variety of techniques including x-ray diffraction, optical, scanning and transmission electron microscopy, x-ray fluorescence, and energy dispersive x-ray spectroscopy were employed to characterize the microstructure and chemistry of the laser additively manufactured 316L stainless steel, which are compared with wrought 316L coupons via electrochemical polarization. Apparent segregation of Mo has been found to contribute to a loss of passivity and an increased anodic current density. While porosity will also likely impact the environmental performance (e.g., facilitating crevice corrosion) of AM alloys, this work demonstrates the critical influence of microstructure and heterogeneous solute distributions on the corrosion resistance of laser additively manufactured 316L stainless steel.

Unintended Consequences: How Qualification Constrains Innovation

NASA Technical Reports Server (NTRS)

Brice, Craig A.

2011-01-01

The development and implementation of new materials and manufacturing processes for aerospace application is often hindered by the high cost and long time span associated with current qualification procedures. The data requirements necessary for material and process qualification are extensive and often require millions of dollars and multiple years to complete. Furthermore, these qualification data can become obsolete for even minor changes to the processing route. This burden is a serious impediment to the pursuit of revolutionary new materials and more affordable processing methods for air vehicle structures. The application of integrated computational materials engineering methods to this problem can help to reduce the barriers to rapid insertion of new materials and processes. By establishing predictive capability for the development of microstructural features in relation to processing and relating this to critical property characteristics, a streamlined approach to qualification is possible. This paper critically examines the advantages and challenges to a modeling-assisted qualification approach for aerospace structural materials. An example of how this approach might apply towards the emerging field of additive manufacturing is discussed in detail.

Application of Twin Screw Extrusion in the Manufacture of Cocrystals, Part I: Four Case Studies

PubMed Central

Daurio, Dominick; Medina, Cesar; Saw, Robert; Nagapudi, Karthik; Alvarez-Núñez, Fernando

2011-01-01

The application of twin screw extrusion (TSE) as a scalable and green process for the manufacture of cocrystals was investigated. Four model cocrystal forming systems, Caffeine-Oxalic acid, Nicotinamide-trans cinnamic acid, Carbamazepine-Saccharin, and Theophylline-Citric acid, were selected for the study. The parameters of the extrusion process that influenced cocrystal formation were examined. TSE was found to be an effective method to make cocrystals for all four systems studied. It was demonstrated that temperature and extent of mixing in the extruder were the primary process parameters that influenced extent of conversion to the cocrystal in neat TSE experiments. In addition to neat extrusion, liquid-assisted TSE was also demonstrated for the first time as a viable process for making cocrystals. Notably, the use of catalytic amount of benign solvents led to a lowering of processing temperatures required to form the cocrystal in the extruder. TSE should be considered as an efficient, scalable, and environmentally friendly process for the manufacture of cocrystals with little to no solvent requirements. PMID:24310598

The Practical Application of Uav-Based Photogrammetry Under Economic Aspects

NASA Astrophysics Data System (ADS)

Sauerbier, M.; Siegrist, E.; Eisenbeiss, H.; Demir, N.

2011-09-01

Nowadays, small size UAVs (Unmanned Aerial Vehicles) have reached a level of practical reliability and functionality that enables this technology to enter the geomatics market as an additional platform for spatial data acquisition. Though one could imagine a wide variety of interesting sensors to be mounted on such a device, here we will focus on photogrammetric applications using digital cameras. In praxis, UAV-based photogrammetry will only be accepted if it a) provides the required accuracy and an additional value and b) if it is competitive in terms of economic application compared to other measurement technologies. While a) was already proven by the scientific community and results were published comprehensively during the last decade, b) still has to be verified under real conditions. For this purpose, a test data set representing a realistic scenario provided by ETH Zurich was used to investigate cost effectiveness and to identify weak points in the processing chain that require further development. Our investigations are limited to UAVs carrying digital consumer cameras, for larger UAVs equipped with medium format cameras the situation has to be considered as significantly different. Image data was acquired during flights using a microdrones MD4-1000 quadrocopter equipped with an Olympus PE-1 digital compact camera. From these images, a subset of 5 images was selected for processing in order to register the effort of time required for the whole production chain of photogrammetric products. We see the potential of mini UAV-based photogrammetry mainly in smaller areas, up to a size of ca. 100 hectares. Larger areas can be efficiently covered by small airplanes with few images, reducing processing effort drastically. In case of smaller areas of a few hectares only, it depends more on the products required. UAVs can be an enhancement or alternative to GNSS measurements, terrestrial laser scanning and ground based photogrammetry. We selected the above mentioned test data from a project featuring an area of interest within the practical range for mini UAVs. While flight planning and flight operation are already quite efficient processes, the bottlenecks identified are mainly related to image processing. Although we used specific software for image processing, the identified gaps in the processing chain today are valid for most commercial photogrammetric software systems on the market. An outlook proposing improvements for a practicable workflow applicable in projects in private economy will be given.

Comparison of Thermal and Non-Thermal Processing of Swine Feed and the Use of Selected Feed Additives on Inactivation of Porcine Epidemic Diarrhea Virus (PEDV).

PubMed

Trudeau, Michaela P; Verma, Harsha; Sampedro, Fernando; Urriola, Pedro E; Shurson, Gerald C; McKelvey, Jessica; Pillai, Suresh D; Goyal, Sagar M

2016-01-01

Infection with porcine epidemic diarrhea virus (PEDV) causes diarrhea, vomiting, and high mortality in suckling pigs. Contaminated feed has been suggested as a vehicle of transmission for PEDV. The objective of this study was to compare thermal and electron beam processing, and the inclusion of feed additives on the inactivation of PEDV in feed. Feed samples were spiked with PEDV and then heated to 120-145°C for up to 30 min or irradiated at 0-50 kGy. Another set of feed samples spiked with PEDV and mixed with Ultracid P (Nutriad), Activate DA (Novus International), KEM-GEST (Kemin Agrifood), Acid Booster (Agri-Nutrition), sugar or salt was incubated at room temperature (~25°C) for up to 21 days. At the end of incubation, the virus titers were determined by inoculation of Vero-81 cells and the virus inactivation kinetics were modeled using the Weibull distribution model. The Weibull kinetic parameter delta represented the time or eBeam dose required to reduce virus concentration by 1 log. For thermal processing, delta values ranged from 16.52 min at 120°C to 1.30 min at 145°C. For eBeam processing, a target dose of 50 kGy reduced PEDV concentration by 3 log. All additives tested were effective in reducing the survival of PEDV when compared with the control sample (delta = 17.23 days). Activate DA (0.81) and KEM-GEST (3.28) produced the fastest inactivation. In conclusion, heating swine feed at temperatures over 130°C or eBeam processing of feed with a dose over 50 kGy are effective processing steps to reduce PEDV survival. Additionally, the inclusion of selected additives can decrease PEDV survivability.

Research and development on membrane processes for removal of acid gases during coal gasification. Final report, 20 June 1975-19 October 1976

DOE Office of Scientific and Technical Information (OSTI.GOV)

Petersen, R.J.; Cadotte, J.E.; Conway, E.J.

1976-01-01

The object of this program was to develop novel and unique membranes for separating acid gases from coal gasification streams. Many candidate membranes, including cationic, hydrophilic, and silicone, were tested. Optimum separation properties were possessed by membranes formulated from crosslinked methyl cellulose coated on polysulfone support films. The observed separation properties were explained theoretically by the solubility of the various gases in the water contained within the membranes rather than by activated transport. Each of the acid gas clean-up processes considered required additional sulfur clean-up, a guard chamber, and a Claus plant for recovering sulfur. These additional costs were calculatedmore » and added to the base costs for acid gas removal from the raw SNG. When the additional costs were added to the costs of the Rectisol, Benfield, Sulfinol, and fluidized dolomite processes the total costs ranged from 43 to 49 cents/Mscf. For the membrane process the additional sulfur removal costs were about 3.3 cents/Mscf to be added to the base costs for acid gas removal. The best membrane composition found during this program, one which exhibited a CO/sub 2//H/sub 2/ selectivity of 13 at a CO/sub 2/ flux of 6 ft/sup 3//ft/sup 2/-hr-100 psi, would entail a process cost of about 53 cents/Mscf with these additions. This is about 7 cents/Mscf more than for the average of the other processes. No better membrane performance is predicted on the basis of the experiments performed. Without a shift in several cost factors, membranes cannot be competitive. The possibility that reduced energy availability could lead to such shifts should not be discounted but is not foreseen in the near future.« less

Sustainability Characterization for Additive Manufacturing.

PubMed

Mani, Mahesh; Lyons, Kevin W; Gupta, S K

2014-01-01

Additive manufacturing (AM) has the potential to create geometrically complex parts that require a high degree of customization, using less material and producing less waste. Recent studies have shown that AM can be an economically viable option for use by the industry, yet there are some inherent challenges associated with AM for wider acceptance. The lack of standards in AM impedes its use for parts production since industries primarily depend on established standards in processes and material selection to ensure the consistency and quality. Inability to compare AM performance against traditional manufacturing methods can be a barrier for implementing AM processes. AM process sustainability has become a driver due to growing environmental concerns for manufacturing. This has reinforced the importance to understand and characterize AM processes for sustainability. Process characterization for sustainability will help close the gaps for comparing AM performance to traditional manufacturing methods. Based on a literature review, this paper first examines the potential environmental impacts of AM. A methodology for sustainability characterization of AM is then proposed to serve as a resource for the community to benchmark AM processes for sustainability. Next, research perspectives are discussed along with relevant standardization efforts.

Comparison of electron beam and laser beam powder bed fusion additive manufacturing process for high temperature turbine component materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dryepondt, Sebastien N; Pint, Bruce A; Ryan, Daniel

2016-04-01

The evolving 3D printer technology is now at the point where some turbine components could be additive manufactured (AM) for both development and production purposes. However, this will require a significant evaluation program to qualify the process and components to meet current design and quality standards. The goal of the project was to begin characterization of the microstructure and mechanical properties of Nickel Alloy X (Ni-22Cr-18Fe-9Mo) test bars fabricated by powder bed fusion (PBF) AM processes that use either an electron beam (EB) or laser beam (LB) power source. The AM materials produced with the EB and LB processes displayedmore » significant differences in microstructure and resultant mechanical properties. Accordingly, during the design analysis of AM turbine components, the specific mechanical behavior of the material produced with the selected AM process should be considered. Comparison of the mechanical properties of both the EB and LB materials to those of conventionally processed Nickel Alloy X materials indicates the subject AM materials are viable alternatives for manufacture of some turbine components.« less

Utilization and Harmonization of Adult Accelerometry Data: Review and Expert Consensus.

PubMed

Wijndaele, Katrien; Westgate, Kate; Stephens, Samantha K; Blair, Steven N; Bull, Fiona C; Chastin, Sebastien F M; Dunstan, David W; Ekelund, Ulf; Esliger, Dale W; Freedson, Patty S; Granat, Malcolm H; Matthews, Charles E; Owen, Neville; Rowlands, Alex V; Sherar, Lauren B; Tremblay, Mark S; Troiano, Richard P; Brage, Søren; Healy, Genevieve N

2015-10-01

This study aimed to describe the scope of accelerometry data collected internationally in adults and to obtain a consensus from measurement experts regarding the optimal strategies to harmonize international accelerometry data. In March 2014, a comprehensive review was undertaken to identify studies that collected accelerometry data in adults (sample size, n ≥ 400). In addition, 20 physical activity experts were invited to participate in a two-phase Delphi process to obtain consensus on the following: unique research opportunities available with such data, additional data required to address these opportunities, strategies for enabling comparisons between studies/countries, requirements for implementing/progressing such strategies, and value of a global repository of accelerometry data. The review identified accelerometry data from more than 275,000 adults from 76 studies across 36 countries. Consensus was achieved after two rounds of the Delphi process; 18 experts participated in one or both rounds. The key opportunities highlighted were the ability for cross-country/cross-population comparisons and the analytic options available with the larger heterogeneity and greater statistical power. Basic sociodemographic and anthropometric data were considered a prerequisite for this. Disclosure of monitor specifications and protocols for data collection and processing were deemed essential to enable comparison and data harmonization. There was strong consensus that standardization of data collection, processing, and analytical procedures was needed. To implement these strategies, communication and consensus among researchers, development of an online infrastructure, and methodological comparison work were required. There was consensus that a global accelerometry data repository would be beneficial and worthwhile. This foundational resource can lead to implementation of key priority areas and identification of future directions in physical activity epidemiology, population monitoring, and burden of disease estimates.

Modeling the impact of changing patient transportation systems on peri-operative process performance in a large hospital: insights from a computer simulation study.

PubMed

Segev, Danny; Levi, Retsef; Dunn, Peter F; Sandberg, Warren S

2012-06-01

Transportation of patients is a key hospital operational activity. During a large construction project, our patient admission and prep area will relocate from immediately adjacent to the operating room suite to another floor of a different building. Transportation will require extra distance and elevator trips to deliver patients and recycle transporters (specifically: personnel who transport patients). Management intuition suggested that starting all 52 first cases simultaneously would require many of the 18 available elevators. To test this, we developed a data-driven simulation tool to allow decision makers to simultaneously address planning and evaluation questions about patient transportation. We coded a stochastic simulation tool for a generalized model treating all factors contributing to the process as JAVA objects. The model includes elevator steps, explicitly accounting for transporter speed and distance to be covered. We used the model for sensitivity analyses of the number of dedicated elevators, dedicated transporters, transporter speed and the planned process start time on lateness of OR starts and the number of cases with serious delays (i.e., more than 15 min). Allocating two of the 18 elevators and 7 transporters reduced lateness and the number of cases with serious delays. Additional elevators and/or transporters yielded little additional benefit. If the admission process produced ready-for-transport patients 20 min earlier, almost all delays would be eliminated. Modeling results contradicted clinical managers' intuition that starting all first cases on time requires many dedicated elevators. This is explained by the principle of decreasing marginal returns for increasing capacity when there are other limiting constraints in the system.

Utilization of coal fly ash in solidification of liquid radioactive waste from research reactor.

PubMed

Osmanlioglu, Ahmet Erdal

2014-05-01

In this study, the potential utilization of fly ash was investigated as an additive in solidification process of radioactive waste sludge from research reactor. Coal formations include various percentages of natural radioactive elements; therefore, coal fly ash includes various levels of radioactivity. For this reason, fly ashes have to be evaluated for potential environmental implications in case of further usage in any construction material. But for use in solidification of radioactive sludge, the radiological effects of fly ash are in the range of radioactive waste management limits. The results show that fly ash has a strong fixing capacity for radioactive isotopes. Specimens with addition of 5-15% fly ash to concrete was observed to be sufficient to achieve the target compressive strength of 20 MPa required for near-surface disposal. An optimum mixture comprising 15% fly ash, 35% cement, and 50% radioactive waste sludge could provide the solidification required for long-term storage and disposal. The codisposal of radioactive fly ash with radioactive sludge by solidification decreases the usage of cement in solidification process. By this method, radioactive fly ash can become a valuable additive instead of industrial waste. This study supports the utilization of fly ash in industry and the solidification of radioactive waste in the nuclear industry.

Novel arrangement for an electro-Fenton reactor that does not require addition of iron, acid and a final neutralization stage. Towards the development of a cost-effective technology for the treatment of wastewater.

PubMed

Fernández, Dennys; Robles, Irma; Rodríguez-Valadez, Francisco J; Godínez, Luis A

2018-05-01

A novel arrangement for an electro-Fenton reactor aimed to treat neutral wastewater is presented. The arrangement consists on three-compartments in series, two of them packed with a cation exchange resin and one positioned between these, containing a polarized activated carbon column where the electrochemical generation of the Fenton reagent takes place. While the hydroxyl radicals electrochemically produced in-situ, react with the pollutant species adsorbed on the activated carbon cathode, the resin compartments administrate and collect the iron cation and the hydrated proton species in alternating flow direction cycles. The resulting process is a system that does not require acid or iron chemical addition to the process while at the same time, renders decontaminated water free of iron-dissolved species at neutral pH. The proposed electrochemical reactor arrangement is therefore the basis for the design of commercially viable electro-Fenton reactors in which the addition and subsequent removal of acid and iron chemicals is avoided; two of the currently most limiting features for the development of electro-Fenton technology for treating wastewater. Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.

Metallic Fuel Casting Development and Parameter Optimization Simulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

R.S. Fielding; J. Crapps; C. Unal

One of the advantages of metallic fuel is the abilility to cast the fuel slugs to near net shape with little additional processing. However, the high aspect ratio of the fuel is not ideal for casting. EBR-II fuel was cast using counter gravity injection casting (CGIC) but, concerns have been raised concerning the feasibility of this process for americium bearing alloys. The Fuel Cycle Research and Development program has begun developing gravity casting techniques suitable for fuel production. Compared to CGIC gravity casting does not require a large heel that then is recycled, does not require application of a vacuummore » during melting, and is conducive to re-usable molds. Development has included fabrication of two separate benchscale, approximately 300 grams, systems. To shorten development time computer simulations have been used to ensure mold and crucible designs are feasible and to identify which fluid properties most affect casting behavior and therefore require more characterization.« less

Test and Validation of the Mars Science Laboratory Robotic Arm

NASA Technical Reports Server (NTRS)

Robinson, M.; Collins, C.; Leger, P.; Kim, W.; Carsten, J.; Tompkins, V.; Trebi-Ollennu, A.; Florow, B.

2013-01-01

The Mars Science Laboratory Robotic Arm (RA) is a key component for achieving the primary scientific goals of the mission. The RA supports sample acquisition by precisely positioning a scoop above loose regolith or accurately preloading a percussive drill on Martian rocks or rover-mounted organic check materials. It assists sample processing by orienting a sample processing unit called CHIMRA through a series of gravity-relative orientations and sample delivery by positioning the sample portion door above an instrument inlet or the observation tray. In addition the RA facilitates contact science by accurately positioning the dust removal tool, Alpha Particle X-Ray Spectrometer (APXS) and the Mars Hand Lens Imager (MAHLI) relative to surface targets. In order to fulfill these seemingly disparate science objectives the RA must satisfy a variety of accuracy and performance requirements. This paper describes the necessary arm requirement specification and the test campaign to demonstrate these requirements were satisfied.

Environmental monitoring of the orbiter payload bay and Orbiter Processing Facilities

NASA Technical Reports Server (NTRS)

Bartelson, D. W.; Johnson, A. M.

1985-01-01

Contamination control in the Orbiter Processing Facility (OPF) is studied. The clean level required in the OPF is generally clean, which means no residue, dirt, debris, or other extraneous contamination; various methods of maintaining this level of cleanliness are described. The monitoring and controlling of the temperature, relative humidity, and air quality in the OPF are examined. Additional modifications to the OPF to improve contamination control are discussed. The methods used to maintain the payload changeout room at a level of visually clean, no particulates are to be detected by the unaided eye, are described. The payload bay (PLB) must sustain the cleanliness level required for the specific Orbiter's mission; the three levels of clean are defined as: (1) standard, (2) sensitive, and (3) high sensitive. The cleaning and inspection verification required to achieve the desired cleanliness level on a variety of PLB surface types are examined.

Structural verification for GAS experiments

NASA Technical Reports Server (NTRS)

Peden, Mark Daniel

1992-01-01

The purpose of this paper is to assist the Get Away Special (GAS) experimenter in conducting a thorough structural verification of its experiment structural configuration, thus expediting the structural review/approval process and the safety process in general. Material selection for structural subsystems will be covered with an emphasis on fasteners (GSFC fastener integrity requirements) and primary support structures (Stress Corrosion Cracking requirements and National Space Transportation System (NSTS) requirements). Different approaches to structural verifications (tests and analyses) will be outlined especially those stemming from lessons learned on load and fundamental frequency verification. In addition, fracture control will be covered for those payloads that utilize a door assembly or modify the containment provided by the standard GAS Experiment Mounting Plate (EMP). Structural hazard assessment and the preparation of structural hazard reports will be reviewed to form a summation of structural safety issues for inclusion in the safety data package.

Maximization of DRAM yield by control of surface charge and particle addition during high dose implantation

NASA Astrophysics Data System (ADS)

Horvath, J.; Moffatt, S.

1991-04-01

Ion implantation processing exposes semiconductor devices to an energetic ion beam in order to deposit dopant ions in shallow layers. In addition to this primary process, foreign materials are deposited as particles and surface films. The deposition of particles is a major cause of IC yield loss and becomes even more significant as device dimensions are decreased. Control of particle addition in a high-volume production environment requires procedures to limit beamline and endstation sources, control of particle transport, cleaning procedures and a well grounded preventative maintenance philosophy. Control of surface charge by optimization of the ion beam and electron shower conditions and measurement with a real-time charge sensor has been effective in improving the yield of NMOS and CMOS DRAMs. Control of surface voltages to a range between 0 and -20 V was correlated with good implant yield with PI9200 implanters for p + and n + source-drain implants.

IR-laser assisted additive freeform optics manufacturing.

PubMed

Hong, Zhihan; Liang, Rongguang

2017-08-02

Computer-controlled additive manufacturing (AM) processes, also known as three-dimensional (3D) printing, create 3D objects by the successive adding of a material or materials. While there have been tremendous developments in AM, the 3D printing of optics is lagging due to the limits in materials and tight requirements for optical applicaitons. We propose a new precision additive freeform optics manufacturing (AFOM) method using an pulsed infrared (IR) laser. Compared to ultraviolet (UV) curable materials, thermally curable optical silicones have a number of advantages, such as strong UV stability, non-yellowing, and high transmission, making it particularly suitable for optical applications. Pulsed IR laser radiation offers a distinct advantage in processing optical silicones, as the high peak intensity achieved in the focal region allows for curing the material quickly, while the brief duration of the laser-material interaction creates a negligible heat-affected zone.

New mission requirements methodologies for services provided by the Office of Space Communications

NASA Technical Reports Server (NTRS)

Holmes, Dwight P.; Hall, J. R.; Macoughtry, William; Spearing, Robert

1993-01-01

The Office of Space Communications, NASA Headquarters, has recently revised its methodology for receiving, accepting and responding to customer requests for use of that office's tracking and communications capabilities. This revision is the result of a process which has become over-burdened by the size of the currently active and proposed missions set, requirements reviews that focus on single missions rather than on mission sets, and negotiations most often not completed early enough to effect needed additions to capacity or capability prior to launch. The requirements-coverage methodology described is more responsive to project/program needs and provides integrated input into the NASA budget process early enough to effect change, and describes the mechanisms and tools in place to insure a value-added process which will benefit both NASA and its customers. Key features of the requirements methodology include the establishment of a mechanism for early identification of and systems trades with new customers, and delegates the review and approval of requirements documents to NASA centers in lieu of Headquarters, thus empowering the system design teams to establish and negotiate the detailed requirements with the user. A Mission Requirements Request (MRR) is introduced to facilitate early customer interaction. The expected result is that the time to achieve an approved set of implementation requirements which meet the customer's needs can be greatly reduced. Finally, by increasing the discipline in requirements management, through the use of base lining procedures, a tighter coupling between customer requirements and the budget is provided. A twice-yearly projection of customer requirements accommodation, designated as the Capacity Projection Plan (CPP), provides customer feedback allowing the entire mission set to be serviced.

Putting ROSE to Work: A Proposed Application of a Request-Oriented Scheduling Engine for Space Station Operations

NASA Technical Reports Server (NTRS)

Jaap, John; Muery, Kim

2000-01-01

Scheduling engines are found at the core of software systems that plan and schedule activities and resources. A Request-Oriented Scheduling Engine (ROSE) is one that processes a single request (adding a task to a timeline) and then waits for another request. For the International Space Station, a robust ROSE-based system would support multiple, simultaneous users, each formulating requests (defining scheduling requirements), submitting these requests via the internet to a single scheduling engine operating on a single timeline, and immediately viewing the resulting timeline. ROSE is significantly different from the engine currently used to schedule Space Station operations. The current engine supports essentially one person at a time, with a pre-defined set of requirements from many payloads, working in either a "batch" scheduling mode or an interactive/manual scheduling mode. A planning and scheduling process that takes advantage of the features of ROSE could produce greater customer satisfaction at reduced cost and reduced flow time. This paper describes a possible ROSE-based scheduling process and identifies the additional software component required to support it. Resulting changes to the management and control of the process are also discussed.

Modern Corneal Eye-Banking Using a Software-Based IT Management Solution.

PubMed

Kern, C; Kortuem, K; Wertheimer, C; Nilmayer, O; Dirisamer, M; Priglinger, S; Mayer, W J

2018-01-01

Increasing government legislation and regulations in manufacturing have led to additional documentation regarding the pharmaceutical product requirements of corneal grafts in the European Union. The aim of this project was to develop a software within a hospital information system (HIS) to support the documentation process, to improve the management of the patient waiting list and to increase informational flow between the clinic and eye bank. After an analysis of the current documentation process, a new workflow and software were implemented in our electronic health record (EHR) system. The software takes over most of the documentation and reduces the time required for record keeping. It guarantees real-time tracing of all steps during human corneal tissue processing from the start of production until allocation during surgery and includes follow-up within the HIS. Moreover, listing of the patient for surgery as well as waiting list management takes place in the same system. The new software for corneal eye banking supports the whole process chain by taking over both most of the required documentation and the management of the transplant waiting list. It may provide a standardized IT-based solution for German eye banks working within the same HIS.

The Design of a High Performance Earth Imagery and Raster Data Management and Processing Platform

NASA Astrophysics Data System (ADS)

Xie, Qingyun

2016-06-01

This paper summarizes the general requirements and specific characteristics of both geospatial raster database management system and raster data processing platform from a domain-specific perspective as well as from a computing point of view. It also discusses the need of tight integration between the database system and the processing system. These requirements resulted in Oracle Spatial GeoRaster, a global scale and high performance earth imagery and raster data management and processing platform. The rationale, design, implementation, and benefits of Oracle Spatial GeoRaster are described. Basically, as a database management system, GeoRaster defines an integrated raster data model, supports image compression, data manipulation, general and spatial indices, content and context based queries and updates, versioning, concurrency, security, replication, standby, backup and recovery, multitenancy, and ETL. It provides high scalability using computer and storage clustering. As a raster data processing platform, GeoRaster provides basic operations, image processing, raster analytics, and data distribution featuring high performance computing (HPC). Specifically, HPC features include locality computing, concurrent processing, parallel processing, and in-memory computing. In addition, the APIs and the plug-in architecture are discussed.

Exploiting Process-Related Advantages of Selective Laser Melting for the Production of High-Manganese Steel.

PubMed

Haase, Christian; Bültmann, Jan; Hof, Jan; Ziegler, Stephan; Bremen, Sebastian; Hinke, Christian; Schwedt, Alexander; Prahl, Ulrich; Bleck, Wolfgang

2017-01-11

Metal additive manufacturing has strongly gained scientific and industrial importance during the last decades due to the geometrical flexibility and increased reliability of parts, as well as reduced equipment costs. Within the field of metal additive manufacturing methods, selective laser melting (SLM) is an eligible technique for the production of fully dense bulk material with complex geometry. In the current study, we addressed the application of SLM for processing a high-manganese TRansformation-/TWinning-Induced Plasticity (TRIP/TWIP) steel. The solidification behavior was analyzed by careful characterization of the as-built microstructure and element distribution using optical and scanning electron microscopy (SEM). In addition, the deformation behavior was studied using uniaxial tensile testing and SEM. Comparison with conventionally produced TRIP/TWIP steel revealed that elemental segregation, which is normally very pronounced in high-manganese steels and requires energy-intensive post processing, is reduced due to the high cooling rates during SLM. Also, the very fast cooling promoted ε- and α'-martensite formation prior to deformation. The superior strength and pronounced anisotropy of the SLM-produced material was correlated with the microstructure based on the process-specific characteristics.

Exploiting Process-Related Advantages of Selective Laser Melting for the Production of High-Manganese Steel

PubMed Central

Haase, Christian; Bültmann, Jan; Hof, Jan; Ziegler, Stephan; Bremen, Sebastian; Hinke, Christian; Schwedt, Alexander; Prahl, Ulrich; Bleck, Wolfgang

2017-01-01

Metal additive manufacturing has strongly gained scientific and industrial importance during the last decades due to the geometrical flexibility and increased reliability of parts, as well as reduced equipment costs. Within the field of metal additive manufacturing methods, selective laser melting (SLM) is an eligible technique for the production of fully dense bulk material with complex geometry. In the current study, we addressed the application of SLM for processing a high-manganese TRansformation-/TWinning-Induced Plasticity (TRIP/TWIP) steel. The solidification behavior was analyzed by careful characterization of the as-built microstructure and element distribution using optical and scanning electron microscopy (SEM). In addition, the deformation behavior was studied using uniaxial tensile testing and SEM. Comparison with conventionally produced TRIP/TWIP steel revealed that elemental segregation, which is normally very pronounced in high-manganese steels and requires energy-intensive post processing, is reduced due to the high cooling rates during SLM. Also, the very fast cooling promoted ε- and α’-martensite formation prior to deformation. The superior strength and pronounced anisotropy of the SLM-produced material was correlated with the microstructure based on the process-specific characteristics. PMID:28772416

Multi-Disciplinary, Multi-Fidelity Discrete Data Transfer Using Degenerate Geometry Forms

NASA Technical Reports Server (NTRS)

Olson, Erik D.

2016-01-01

In a typical multi-fidelity design process, different levels of geometric abstraction are used for different analysis methods, and transitioning from one phase of design to the next often requires a complete re-creation of the geometry. To maintain consistency between lower-order and higher-order analysis results, Vehicle Sketch Pad (OpenVSP) recently introduced the ability to generate and export several degenerate forms of the geometry, representing the type of abstraction required to perform low- to medium-order analysis for a range of aeronautical disciplines. In this research, the functionality of these degenerate models was extended, so that in addition to serving as repositories for the geometric information that is required as input to an analysis, the degenerate models can also store the results of that analysis mapped back onto the geometric nodes. At the same time, the results are also mapped indirectly onto the nodes of lower-order degenerate models using a process called aggregation, and onto higher-order models using a process called disaggregation. The mapped analysis results are available for use by any subsequent analysis in an integrated design and analysis process. A simple multi-fidelity analysis process for a single-aisle subsonic transport aircraft is used as an example case to demonstrate the value of the approach.

Process' standardization and change management in higher education. The case of TEI of Athens

NASA Astrophysics Data System (ADS)

Chalaris, Ioannis; Chalaris, Manolis; Gritzalis, Stefanos; Belsis, Petros

2015-02-01

The establishment of mature operational procedures and the effort of standardizing and certifying these procedures is a particularly arduous and demanding task which requires strong commitment from management to the existing objectives, administrative stability and continuity, availability of resources, an adequate implementation team with support from all stakeholders and of course great tolerance until tangible results of the investment are shown. Ensuring these conditions, particularly in times of economic crisis, is an extremely difficult task for large organizations such as TEI of Athens where there is heterogeneity in personnel and changes in the administrative hierarchy arise plethora of additional difficulties and require an effective change management. In this work we depict the path of standardization and certification of administrative functions of TEI of Athens, with emphasis on difficulties encountered and how to address them and in particular issues of change management and the culture related to this effort. The requirement for infrastructure needed to be maintained in processes and tools process & strategic management is embodied, in order to evolve mechanisms for continuous improvement processes and storage / recovery of the resulting knowledge. The work concludes with a general design of a road map of internal audit and continuous improvement processes for a large institution of higher education.

NASA guidelines for assuring the adequacy and appropriateness of security safeguards in sensitive applications

NASA Technical Reports Server (NTRS)

Tompkins, F. G.

1984-01-01

The Office of Management and Budget (OMB) Circular A-71, transmittal Memorandum No. 1, requires that each agency establish a management control process to assure that appropriate administrative, physical and technical safeguards are incorporated into all new computer applications. In addition to security specifications, the management control process should assure that the safeguards are adequate for the application. The security activities that should be integral to the system development process are examined. The software quality assurance process to assure that adequate and appropriate controls are incorporated into sensitive applications is also examined. Security for software packages is also discussed.

Final Report - Glass Formulation Testing to Increase Sulfate Volatilization from Melter, VSL-04R4970-1, Rev. 0, dated 2/24/05

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kruger, Albert A.; Matlack, K. A.; Pegg, I. L.

2013-11-13

The principal objectives of the DM100 and DM10 tests were to determine the impact of four different organics and one inorganic feed additive on sulfate volatilization and to determine the sulfur partitioning between the glass and the off-gas system. The tests provided information on melter processing characteristics and off-gas data including sulfur incorporation and partitioning. A series of DM10 and DM100 melter tests were conducted using a LAW Envelope A feed. The testing was divided into three parts. The first part involved a series of DM10 melter tests with four different organic feed additives: sugar, polyethylene glycol (PEG), starch, andmore » urea. The second part involved two confirmatory 50-hour melter tests on the DM100 using the best combination of reductants and conditions based on the DM10 results. The third part was performed on the DM100 with feeds containing vanadium oxide (V{sub 2}O{sub 5}) as an inorganic additive to increase sulfur partitioning to the off-gas. Although vanadium oxide is not a reductant, previous testing has shown that vanadium shows promise for partitioning sulfur to the melter exhaust, presumably through its known catalytic effect on the SO{sub 2}/SO{sub 3} reaction. Crucible-scale tests were conducted prior to the melter tests to confirm that the glasses and feeds would be processable in the melter and that the glasses would meet the waste form (ILAW) performance requirements. Thus, the major objectives of these tests were to: Perform screening tests on the DM10 followed by tests on the DM100-WV system using a LAW -Envelope A feed with four organic additives to assess their impact on sulfur volatilization. Perform tests on the DM100-WV system using a LAW -Envelope A feed containing vanadium oxide to assess its impact on sulfur volatilization. Determine feed processability and product quality with the above additives. Collect melter emissions data to determine the effect of additives on sulfur partitioning and melter emissions. Collect and analyze discharged glass to determine sulfur retention in the glass. Prepare and characterize feeds and glasses with the additives to confirm that the feeds and the glass melts are suitable for processing in the DM100 melter. Prepare and characterize glasses with the additives to confirm that the glasses meet the waste form (ILAW) performance requirements.« less

The effect of switchable water additives on clay settling.

PubMed

Chen, Chien-Shun; Lau, Ying Yin; Mercer, Sean M; Robert, Tobias; Horton, J Hugh; Jessop, Philip G

2013-01-01

The recycling of process water from strip mining extractions is a very relevant task both industrially and environmentally. The sedimentation of fine tailings during such processes, however, can often require long periods of time and/or the addition of flocculants which make later water recycling difficult. We propose the use of switchable water additives as reversible flocculants for clay/water suspensions. Switchable water additives are compounds such as diamines that make it possible to reversibly control the ionic strength of an aqueous solution. Addition of CO(2) to such an aqueous solution causes the ionic strength to rise dramatically, and the change is reversed upon removal of the CO(2). These additives, while in the presence of CO(2), promote the aggregation of clay tailings, reduce settling times, and greatly increase the clarity of the liberated water. The removal of CO(2) from the liberated water regenerates a low ionic strength solution that does not promote clay aggregation and settling until CO(2) is added again. Such reversible behavior would be useful in applications such as oil sands separations in which the recycled water must not promote aggregation. When added to kaolinite and montmorillonite clay suspensions, switchable water provided process waters of lower turbidity than those additives from inorganic salts or by CO(2)-treatment alone. When recollected, the switchable water supernatant was shown to be recyclable over three cycles for enhanced settling of kaolinite. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

International Ultraviolet Explorer Final Archive

NASA Technical Reports Server (NTRS)

1997-01-01

CSC processed IUE images through the Final Archive Data Processing System. Raw images were obtained from both NDADS and the IUEGTC optical disk platters for processing on the Alpha cluster, and from the IUEGTC optical disk platters for DECstation processing. Input parameters were obtained from the IUE database. Backup tapes of data to send to VILSPA were routinely made on the Alpha cluster. IPC handled more than 263 requests for priority NEWSIPS processing during the contract. Staff members also answered various questions and requests for information and sent copies of IUE documents to requesters. CSC implemented new processing capabilities into the NEWSIPS processing systems as they became available. In addition, steps were taken to improve efficiency and throughput whenever possible. The node TORTE was reconfigured as the I/O server for Alpha processing in May. The number of Alpha nodes used for the NEWSIPS processing queue was increased to a maximum of six in measured fashion in order to understand the dependence of throughput on the number of nodes and to be able to recognize when a point of diminishing returns was reached. With Project approval, generation of the VD FITS files was dropped in July. This action not only saved processing time but, even more significantly, also reduced the archive storage media requirements, and the time required to perform the archiving, drastically. The throughput of images verified through CDIVS and processed through NEWSIPS for the contract period is summarized below. The number of images of a given dispersion type and camera that were processed in any given month reflects several factors, including the availability of the required NEWSIPS software system, the availability of the corresponding required calibrations (e.g., the LWR high-dispersion ripple correction and absolute calibration), and the occurrence of reprocessing efforts such as that conducted to incorporate the updated SWP sensitivity-degradation correction in May.

Description of quantum coherence in thermodynamic processes requires constraints beyond free energy.

PubMed

Lostaglio, Matteo; Jennings, David; Rudolph, Terry

2015-03-10

Recent studies have developed fundamental limitations on nanoscale thermodynamics, in terms of a set of independent free energy relations. Here we show that free energy relations cannot properly describe quantum coherence in thermodynamic processes. By casting time-asymmetry as a quantifiable, fundamental resource of a quantum state, we arrive at an additional, independent set of thermodynamic constraints that naturally extend the existing ones. These asymmetry relations reveal that the traditional Szilárd engine argument does not extend automatically to quantum coherences, but instead only relational coherences in a multipartite scenario can contribute to thermodynamic work. We find that coherence transformations are always irreversible. Our results also reveal additional structural parallels between thermodynamics and the theory of entanglement.

Description of quantum coherence in thermodynamic processes requires constraints beyond free energy

NASA Astrophysics Data System (ADS)

Lostaglio, Matteo; Jennings, David; Rudolph, Terry

2015-03-01

Recent studies have developed fundamental limitations on nanoscale thermodynamics, in terms of a set of independent free energy relations. Here we show that free energy relations cannot properly describe quantum coherence in thermodynamic processes. By casting time-asymmetry as a quantifiable, fundamental resource of a quantum state, we arrive at an additional, independent set of thermodynamic constraints that naturally extend the existing ones. These asymmetry relations reveal that the traditional Szilárd engine argument does not extend automatically to quantum coherences, but instead only relational coherences in a multipartite scenario can contribute to thermodynamic work. We find that coherence transformations are always irreversible. Our results also reveal additional structural parallels between thermodynamics and the theory of entanglement.

Process analysis of an in store production of knitted clothing

NASA Astrophysics Data System (ADS)

Buecher, D.; Kemper, M.; Schmenk, B.; Gloy, Y.-S.; Gries, T.

2017-10-01

In the textile and clothing industry, global value-added networks are widespread for textile and clothing production. As a result of global networking, the value chain is fragmented and a great deal of effort is required to coordinate the production processes [1]. In addition, the planning effort on the quantity and design of the goods is high and risky. Today the fashion industry is facing an increasing customer demand for individual and customizable products in addition to short delivery times [2]. These challenges are passed down to the textile and clothing industry decreasing batch sizes and production times. Conventional clothing production cannot fulfill those demands especially when combined with more and more individual or customizable designs. Hence new production concepts have to be developed.

Sewage sludge additive

NASA Technical Reports Server (NTRS)

Kalvinskas, J. J.; Mueller, W. A.; Ingham, J. D. (Inventor)

1980-01-01

The additive is for a raw sewage treatment process of the type where settling tanks are used for the purpose of permitting the suspended matter in the raw sewage to be settled as well as to permit adsorption of the dissolved contaminants in the water of the sewage. The sludge, which settles down to the bottom of the settling tank is extracted, pyrolyzed and activated to form activated carbon and ash which is mixed with the sewage prior to its introduction into the settling tank. The sludge does not provide all of the activated carbon and ash required for adequate treatment of the raw sewage. It is necessary to add carbon to the process and instead of expensive commercial carbon, coal is used to provide the carbon supplement.

Description of quantum coherence in thermodynamic processes requires constraints beyond free energy

PubMed Central

Lostaglio, Matteo; Jennings, David; Rudolph, Terry

2015-01-01

Recent studies have developed fundamental limitations on nanoscale thermodynamics, in terms of a set of independent free energy relations. Here we show that free energy relations cannot properly describe quantum coherence in thermodynamic processes. By casting time-asymmetry as a quantifiable, fundamental resource of a quantum state, we arrive at an additional, independent set of thermodynamic constraints that naturally extend the existing ones. These asymmetry relations reveal that the traditional Szilárd engine argument does not extend automatically to quantum coherences, but instead only relational coherences in a multipartite scenario can contribute to thermodynamic work. We find that coherence transformations are always irreversible. Our results also reveal additional structural parallels between thermodynamics and the theory of entanglement. PMID:25754774

Development of hybrid lifecycle cost estimating tool (HLCET) for manufacturing influenced design tradeoff

NASA Astrophysics Data System (ADS)

Sirirojvisuth, Apinut

In complex aerospace system design, making an effective design decision requires multidisciplinary knowledge from both product and process perspectives. Integrating manufacturing considerations into the design process is most valuable during the early design stages since designers have more freedom to integrate new ideas when changes are relatively inexpensive in terms of time and effort. Several metrics related to manufacturability are cost, time, and manufacturing readiness level (MRL). Yet, there is a lack of structured methodology that quantifies how changes in the design decisions impact these metrics. As a result, a new set of integrated cost analysis tools are proposed in this study to quantify the impacts. Equally important is the capability to integrate this new cost tool into the existing design methodologies without sacrificing agility and flexibility required during the early design phases. To demonstrate the applicability of this concept, a ModelCenter environment is used to develop software architecture that represents Integrated Product and Process Development (IPPD) methodology used in several aerospace systems designs. The environment seamlessly integrates product and process analysis tools and makes effective transition from one design phase to the other while retaining knowledge gained a priori. Then, an advanced cost estimating tool called Hybrid Lifecycle Cost Estimating Tool (HLCET), a hybrid combination of weight-, process-, and activity-based estimating techniques, is integrated with the design framework. A new weight-based lifecycle cost model is created based on Tailored Cost Model (TCM) equations [3]. This lifecycle cost tool estimates the program cost based on vehicle component weights and programmatic assumptions. Additional high fidelity cost tools like process-based and activity-based cost analysis methods can be used to modify the baseline TCM result as more knowledge is accumulated over design iterations. Therefore, with this concept, the additional manufacturing knowledge can be used to identify a more accurate lifecycle cost and facilitate higher fidelity tradeoffs during conceptual and preliminary design. Advanced Composite Cost Estimating Model (ACCEM) is employed as a process-based cost component to replace the original TCM result of the composite part production cost. The reason for the replacement is that TCM estimates production costs from part weights as a result of subtractive manufacturing of metallic origin such as casting, forging, and machining processes. A complexity factor can sometimes be adjusted to reflect different types of metal and machine settings. The TCM assumption, however, gives erroneous results when applied to additive processes like those of composite manufacturing. Another innovative aspect of this research is the introduction of a work measurement technique called Maynard Operation Sequence Technique (MOST) to be used, similarly to Activity-Based Costing (ABC) approach, to estimate manufacturing time of a part by virtue of breaking down the operations occurred during its production. ABC allows a realistic determination of cost incurred in each activity, as opposed to using a traditional method of time estimation by analogy or using response surface equations from historical process data. The MOST concept provides a tailored study of an individual process typically required for a new, innovative design. Nevertheless, the MOST idea has some challenges, one of which is its requirement to build a new process from ground up. The process development requires a Subject Matter Expertise (SME) in manufacturing method of the particular design. The SME must have also a comprehensive understanding of the MOST system so that the correct parameters are chosen. In practice, these knowledge requirements may demand people from outside of the design discipline and a priori training of MOST. To relieve the constraint, this study includes an entirely new sub-system architecture that comprises 1) a knowledge-based system to provide the required knowledge during the process selection; and 2) a new user-interface to guide the parameter selection when building the process using MOST. Also included in this study is the demonstration of how the HLCET and its constituents can be integrated with a Georgia Tech' Integrated Product and Process Development (IPPD) methodology. The applicability of this work will be shown through a complex aerospace design example to gain insights into how manufacturing knowledge helps make better design decisions during the early stages. The setup process is explained with an example of its utility demonstrated in a hypothetical fighter aircraft wing redesign. The evaluation of the system effectiveness against existing methodologies is illustrated to conclude the thesis.

Carer Participation: Training for People with Intellectual Disabilities in a Chinese Society

ERIC Educational Resources Information Center

Wong, Gary C. T.; Chan, Zenobia C. Y.

2012-01-01

People with intellectual disabilities require training to improve independence, and carers are important partners in the process. Studies show that carers are able to motivate family members with intellectual disabilities to participate in training. In addition, family members may serve as cotrainers. To increase carers' participation, it is…

14 CFR § 1261.412 - Interest, penalties, and administrative costs.

Code of Federal Regulations, 2014 CFR

2014-01-01

...—that is, a bill is mailed before the debt is actually owed—it can include the required interest... debt—that is, the additional costs incurred in processing and handling the debt because it became... from the date that the debt became delinquent. (f) When a debt is paid in partial or installment...

EvoBuild: A Quickstart Toolkit for Programming Agent-Based Models of Evolutionary Processes

ERIC Educational Resources Information Center

Wagh, Aditi; Wilensky, Uri

2018-01-01

Extensive research has shown that one of the benefits of programming to learn about scientific phenomena is that it facilitates learning about mechanisms underlying the phenomenon. However, using programming activities in classrooms is associated with costs such as requiring additional time to learn to program or students needing prior experience…

Tylosin sorption to diatomaceous earth: Investigation of physical processes of tylosin in natural systems and development of mitigation methods

USDA-ARS?s Scientific Manuscript database

Tylosin is a common livestock antibiotic used as a feed additive that could promote antibiotic resistance in the environment. Management of tylosin’s impact on environmental antibiotic resistance requires better understanding of its physical interactions in the environment. Diatomaceous earth (DE) i...

19 CFR 10.248 - Additional requirements for preferential treatment of brassieres.

Code of Federal Regulations, 2010 CFR

2010-04-01

... the port of exportation; (C) In the case of fabric components purchased by the producer or entity... expenses for cutting or other processing to create the fabric components other than knitting to shape, that... shape, that the producer or entity controlling production can verify; or (2) If no exportation to an...

19 CFR 10.228 - Additional requirements for preferential treatment of brassieres.

Code of Federal Regulations, 2010 CFR

2010-04-01

... the port of exportation; (C) In the case of fabric components purchased by the producer or entity... expenses for cutting or other processing to create the fabric components other than knitting to shape, that... shape, that the producer or entity controlling production can verify; or (2) If no exportation to a...

19 CFR 10.228 - Additional requirements for preferential treatment of brassieres.

Code of Federal Regulations, 2011 CFR

2011-04-01

... the port of exportation; (C) In the case of fabric components purchased by the producer or entity... expenses for cutting or other processing to create the fabric components other than knitting to shape, that... shape, that the producer or entity controlling production can verify; or (2) If no exportation to a...

19 CFR 10.248 - Additional requirements for preferential treatment of brassieres.

Code of Federal Regulations, 2011 CFR

2011-04-01

... the port of exportation; (C) In the case of fabric components purchased by the producer or entity... expenses for cutting or other processing to create the fabric components other than knitting to shape, that... shape, that the producer or entity controlling production can verify; or (2) If no exportation to an...

75 FR 66411 - Small Entity Compliance Guide: Women-Owned Small Business Program

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-28

...-Owned Small Business (WOSB) Program. This guide sets forth in plain language the requirements for... effective February 4, 2011 because the agency is in the process of working with the Federal Acquisition Regulatory Council to implement this program in the Federal Acquisition Regulations. In addition, the SBA is...

Fostering Radical Conceptual Change through Dual-Situated Learning Model

ERIC Educational Resources Information Center

She, Hsiao-Ching

2004-01-01

This article examines how the Dual-Situated Learning Model (DSLM) facilitates a radical change of concepts that involve the understanding of matter, process, and hierarchical attributes. The DSLM requires knowledge of students' prior beliefs of science concepts and the nature of these concepts. In addition, DSLM also serves two functions: it…

Poor Performance on Serial Visual Tasks in Persons with Reading Disabilities: Impaired Working Memory?

ERIC Educational Resources Information Center

Ram-Tsur, Ronit; Faust, Miriam; Zivotofsky, Ari Z.

2008-01-01

The present study investigates the performance of persons with reading disabilities (PRD) on a variety of sequential visual-comparison tasks that have different working-memory requirements. In addition, mediating relationships between the sequential comparison process and attention and memory skills were looked for. Our findings suggest that PRD…

Design criteria monograph for metal tanks and tank components

NASA Technical Reports Server (NTRS)

1975-01-01

Significant elements in detail tank design are wall and end structures, weld joints at bulkhead and attachment junctures, and ports and access openings. Additional design considerations are influence and effect of fabrication processes on tank component design, and finally, testing and inspection that are required to establish confidence in tank design.

Easy Ways to Promote Inquiry in a Laboratory Course: The Power of Student Questions

ERIC Educational Resources Information Center

Polacek, Kelly Myer; Keeling, Elena Levine

2005-01-01

To teach students to think like scientists, the authors modified their laboratory course to include regular opportunities for student practice of inquiry and the scientific process. Their techniques are simple; they can be implemented without rewriting lab manuals, require little additional grading beyond typical lab reports, and are applicable…

Phono-Orthographic Interaction and Attentional Control in Children with Reading Disabilities

ERIC Educational Resources Information Center

Cone, Nadia Elise

2012-01-01

Fluent reading requires the effective integration of orthographic and phonological information in addition to intact processing of either type. The current study used a rhyme decision task to examine phono-orthographic interaction in children with reading disabilities (RD) as compared to typically achieving (TA) children. Word pairs were presented…

40 CFR 725.975 - EPA approval of alternative control measures.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) TOXIC SUBSTANCES CONTROL ACT REPORTING REQUIREMENTS AND REVIEW PROCESSES FOR MICROORGANISMS Additional... EPA via EPA's Central Data Exchange (CDX) using EPA-provided e-PMN software in the manner set forth in § 725.25(c). See 40 CFR 720.40(a)(2)(iv) for information on how to obtain e-PMN software. Support...

40 CFR 725.975 - EPA approval of alternative control measures.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) TOXIC SUBSTANCES CONTROL ACT REPORTING REQUIREMENTS AND REVIEW PROCESSES FOR MICROORGANISMS Additional... EPA via EPA's Central Data Exchange (CDX) using EPA-provided e-PMN software in the manner set forth in § 725.25(c). See 40 CFR 720.40(a)(2)(iv) for information on how to obtain e-PMN software. Support...

40 CFR 725.975 - EPA approval of alternative control measures.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) TOXIC SUBSTANCES CONTROL ACT REPORTING REQUIREMENTS AND REVIEW PROCESSES FOR MICROORGANISMS Additional... EPA via EPA's Central Data Exchange (CDX) using EPA-provided e-PMN software in the manner set forth in § 725.25(c). See 40 CFR 720.40(a)(2)(iv) for information on how to obtain e-PMN software. Support...

40 CFR 725.975 - EPA approval of alternative control measures.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) TOXIC SUBSTANCES CONTROL ACT REPORTING REQUIREMENTS AND REVIEW PROCESSES FOR MICROORGANISMS Additional... equivalency to EPA under this part must submit the request to EPA (via CDX) using e-PMN software. See 40 CFR 720.40(a)(2)(ii) for information on how to obtain e-PMN software. Support documents related to these...

Anthropometric Accommodation in Space Suit Design

NASA Technical Reports Server (NTRS)

Rajulu, Sudhakar; Thaxton, Sherry

2007-01-01

Design requirements for next generation hardware are in process at NASA. Anthropometry requirements are given in terms of minimum and maximum sizes for critical dimensions that hardware must accommodate. These dimensions drive vehicle design and suit design, and implicitly have an effect on crew selection and participation. At this stage in the process, stakeholders such as cockpit and suit designers were asked to provide lists of dimensions that will be critical for their design. In addition, they were asked to provide technically feasible minimum and maximum ranges for these dimensions. Using an adjusted 1988 Anthropometric Survey of U.S. Army (ANSUR) database to represent a future astronaut population, the accommodation ranges provided by the suit critical dimensions were calculated. This project involved participation from the Anthropometry and Biomechanics facility (ABF) as well as suit designers, with suit designers providing expertise about feasible hardware dimensions and the ABF providing accommodation analysis. The initial analysis provided the suit design team with the accommodation levels associated with the critical dimensions provided early in the study. Additional outcomes will include a comparison of principal components analysis as an alternate method for anthropometric analysis.

Structural Basis of Vta1 Function in the Multivesicular Body Sorting Pathway

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xiao, Junyu; Xia, Hengchuan; Zhou, Jiahai

The MVB pathway plays essential roles in several eukaryotic cellular processes. Proper function of the MVB pathway requires reversible membrane association of the ESCRTs, a process catalyzed by Vps4 ATPase. Vta1 regulates the Vps4 activity, but its mechanism of action was poorly understood. We report the high-resolution crystal structures of the Did2- and Vps60-binding N-terminal domain and the Vps4-binding C-terminal domain of S. cerevisiae Vta1. The C-terminal domain also mediates Vta1 dimerization and both subunits are required for its function as a Vps4 regulator. Emerging from our analysis is a mechanism of regulation by Vta1 in which the C-terminal domainmore » stabilizes the ATP-dependent double ring assembly of Vps4. In addition, the MIT motif-containing N-terminal domain, projected by a long disordered linker, allows contact between the Vps4 disassembly machinery and the accessory ESCRT-III proteins. This provides an additional level of regulation and coordination for ESCRT-III assembly and disassembly.« less

High Temperature Thermoplastic Additive Manufacturing Using Low-Cost, Open-Source Hardware

NASA Technical Reports Server (NTRS)

Gardner, John M.; Stelter, Christopher J.; Yashin, Edward A.; Siochi, Emilie J.

2016-01-01

Additive manufacturing (or 3D printing) via Fused Filament Fabrication (FFF), also known as Fused Deposition Modeling (FDM), is a process where material is placed in specific locations layer-by-layer to create a complete part. Printers designed for FFF build parts by extruding a thermoplastic filament from a nozzle in a predetermined path. Originally developed for commercial printers, 3D printing via FFF has become accessible to a much larger community of users since the introduction of Reprap printers. These low-cost, desktop machines are typically used to print prototype parts or novelty items. As the adoption of desktop sized 3D printers broadens, there is increased demand for these machines to produce functional parts that can withstand harsher conditions such as high temperature and mechanical loads. Materials meeting these requirements tend to possess better mechanical properties and higher glass transition temperatures (Tg), thus requiring printers with high temperature printing capability. This report outlines the problems and solutions, and includes a detailed description of the machine design, printing parameters, and processes specific to high temperature thermoplastic 3D printing.

Implementation of AMNOG: An industry perspective

PubMed Central

Chuang‐Stein, Christy

2015-01-01

In 2010, the Federal Parliament (Bundestag) of Germany passed a new law (Arzneimittelmarktneuordnungsgesetz, AMNOG) on the regulation of medicinal products that applies to all pharmaceutical products with active ingredients that are launched beginning January 1, 2011. The law describes the process to determine the price at which an approved new product will be reimbursed by the statutory health insurance system. The process consists of two phases. The first phase assesses the additional benefit of the new product versus an appropriate comparator (zweckmäßige Vergleichstherapie, zVT). The second phase involves price negotiation. Focusing on the first phase, this paper investigates requirements of benefit assessment of a new product under this law with special attention on the methods applied by the German authorities on issues such as the choice of the comparator, patient relevant endpoints, subgroup analyses, extent of benefit, determination of net benefit, primary and secondary endpoints, and uncertainty of the additional benefit. We propose alternative approaches to address the requirements in some cases and invite other researchers to help develop solutions in other cases. PMID:26332597

Fibre optic portable rail vehicle detector

NASA Astrophysics Data System (ADS)

Kepak, Stanislav; Cubik, Jakub; Zavodny, Petr; Hejduk, Stanislav; Nedoma, Jan; Davidson, Alan; Vasinek, Vladimir

2016-12-01

During track maintenance operations, the early detection of oncoming rail vehicles is critical for the safety of maintenance personnel. In addition, the detection system should be simple to install at the trackside by minimally qualified personnel. Fibre optic based sensor systems have the inherent advantages of being passive, unaffected by radio frequency interference (RFI) and suffering very low signal attenuation. Such a system therefore represents a good alternative to conventional approaches such as ultrasonic based sensor systems. The proposed system consists of one or more passive fibre trackside sensors and an x86 processing unit located at the work site. The solid fibre connection between sensors and processing unit eliminates the risk of RFI. In addition, the detection system sensors are easy to install with no requirement for electrical power at the sensor site. The system was tested on a tram line in Ostrava with the results obtained indicating the successful detection of all the trams in the monitoring windows using a single sensor. However, the platform allows flexibility in configuring multiple sensors where required by system users.

Structural basis of Vta1 function in the multi-vesicular body sorting pathway

PubMed Central

Xiao, Junyu; Xia, Hengchuan; Zhou, Jiahai; Azmi, Ishara; Davies, Brian A.; Katzmann, David J.; Xu, Zhaohui

2009-01-01

Summary The MVB pathway plays essential roles in several eukaryotic cellular processes. Proper function of the MVB pathway requires reversible membrane association of the ESCRTs, a process catalyzed by Vps4 ATPase. Vta1 regulates the Vps4 activity but its mechanism of action was poorly understood. We report the high-resolution crystal structures of the Did2- and Vps60-binding N-terminal domain and the Vps4-binding C-terminal domain of S. cerevisiae Vta1. The C-terminal domain also mediates Vta1 dimerization and both subunits are required for its function as a Vps4 regulator. Emerging from our analysis is a mechanism of regulation by Vta1 in which the C-terminal domain stabilizes the ATP-dependent double ring assembly of Vps4. In addition, the MIT motif containing N-terminal domain, projected by a long disordered linker, allows contact between the Vps4 disassembly machinery and the accessory ESCRT-III proteins. This provides an additional level of regulation and coordination for ESCRT-III assembly and disassembly. PMID:18194651

EFFECT OF ENDOSPERM HARDNESS ON AN ETHANOL PROCESS USING A GRANULAR STARCH HYDROLYZING ENZYME

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, P; W Liu, D B; Johnston, K D

Granular starch hydrolyzing enzymes (GSHE) can hydrolyze starch at low temperature (32°C). The dry grind process using GSHE (GSH process) has fewer unit operations and no changes in process conditions (pH 4.0 and 32°C) compared to the conventional process because it dispenses with the cooking and liquefaction step. In this study, the effects of endosperm hardness, protease, urea, and GSHE levels on GSH process were evaluated. Ground corn, soft endosperm, and hard endosperm were processed using two GSHE levels (0.1 and 0.4 mL per 100 g ground material) and four treatments of protease and urea addition. Soft and hard endospermmore » materials were obtained by grinding and sifting flaking grits from a dry milling pilot plant; classifications were confirmed using scanning electron microscopy. During 72 h of simultaneous granular starch hydrolysis and fermentation (GSHF), ethanol and glucose profiles were determined using HPLC. Soft endosperm resulted in higher final ethanol concentrations compared to ground corn or hard endosperm. Addition of urea increased final ethanol concentrations for soft and hard endosperm. Protease addition increased ethanol concentrations and fermentation rates for soft endosperm, hard endosperm, and ground corn. The effect of protease addition on ethanol concentrations and fermentation rates was most predominant for soft endosperm, less for hard endosperm, and least for ground corn. Samples (soft endosperm, hard endosperm, or corn) with protease resulted in higher (1.0% to 10.5% v/v) ethanol concentration compared to samples with urea. The GSH process with protease requires little or no urea addition. For fermentation of soft endosperm, GSHE dose can be reduced. Due to nutrients (lipids, minerals, and soluble proteins) present in corn that enhance yeast growth, ground corn fermented faster at the beginning than hard and soft endosperm.« less

Processing liquid organic wastes at the NNL Preston laboratory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coppersthwaite, Duncan; Greenwood, Howard; Docrat, Tahera

2013-07-01

Organic compounds of various kinds have been used in the nuclear industry for numerous duties in uranium chemical, metal and ceramic processing plants. In the course of the various operations undertaken, these organic compounds have become contaminated with uranic material, either accidentally or as an inevitable part of the process. Typically, the chemical/physical form and/or concentration of the uranic content of the organics has prevented disposal. In order to address the issue of contaminated liquid organic wastes, the National Nuclear Laboratory (NNL) has developed a suite of treatments designed to recover uranium and to render the waste suitable for disposal.more » The developed processes are operated at industrial scale via the NNL Preston Laboratory Residue Processing Plant. The Oil Waste Leaching (OWL) Process is a fully industrialised process used for the treatment of contaminated oils with approximately 200 tonnes of uranium contaminated oil being treated to date. The process was originally developed for the treatment of contaminated tributyl phosphate and odourless kerosene which had been adsorbed onto sawdust. However, over the years, the OWL process has been refined for a range of oils including 'water emulsifiable' cutting oils, lubricating oils, hydraulic oils/fluids and 'Fomblin' (fully fluorinated) oils. Chemically, the OWL process has proved capable of treating solvents as well as oils but the highly volatile/flammable nature of many solvents has required additional precautions compared with those required for oil treatment. These additional precautions led to the development of the Solvent Treatment Advanced Rig (STAR), an installation operated under an inert atmosphere. STAR is a small 'module' (100 dm{sup 3} volume) which allows the treatment of both water miscible and immiscible solvents. This paper discusses the challenges associated with the treatment of liquid organic wastes and the process developments which have allowed a wide range of materials to be successfully treated. (authors)« less

Evaluation of Mars CO2 Capture and Gas Separation Technologies

NASA Technical Reports Server (NTRS)

Muscatello, Anthony C.; Santiago-Maldonado, Edgardo; Gibson, Tracy; Devor, Robert; Captain, James

2011-01-01

Recent national policy statements have established that the ultimate destination of NASA's human exploration program is Mars. In Situ Resource Utilization (ISRU) is a key technology required to ,enable such missions and it is appropriate to review progress in this area and continue to advance the systems required to produce rocket propellant, oxygen, and other consumables on Mars using the carbon dioxide atmosphere and other potential resources. The Mars Atmospheric Capture and Gas separation project is selecting, developing, and demonstrating techniques to capture and purify Martian atmospheric gases for their utilization for the production of hydrocarbons, oxygen, and water in ISRU systems. Trace gases will be required to be separated from Martian atmospheric gases to provide pure CO2 to processing elements. In addition, other Martian gases, such as nitrogen and argon, occur in concentrations high enough to be useful as buffer gas and should be captured as well. To achieve these goals, highly efficient gas separation processes will be required. These gas separation techniques are also required across various areas within the ISRU project to support various consumable production processes. The development of innovative gas separation techniques will evaluate the current state-of-the-art for the gas separation required, with the objective to demonstrate and develop light-weight, low-power methods for gas separation. Gas separation requirements include, but are not limited to the selective separation of: (1) methane and water from unreacted carbon oxides (C02-CO) and hydrogen typical of a Sabatier-type process, (2) carbon oxides and water from unreacted hydrogen from a Reverse Water-Gas Shift process, (3)/carbon oxides from oxygen from a trash/waste processing reaction, and (4) helium from hydrogen or oxygen from a propellant scavenging process. Potential technologies for the separations include' freezers, selective membranes, selective solvents, polymeric sorbents, zeolites, and new technologies. This paper summarizes the results of an extensive literature review of candidate technologies for the capture and separation of CO2 and other relevant gases. This information will be used to prioritize the technologies to be developed further during this and other ISRU projects.

Active optical system for advanced 3D surface structuring by laser remelting

NASA Astrophysics Data System (ADS)

Pütsch, O.; Temmler, A.; Stollenwerk, J.; Willenborg, E.; Loosen, P.

2015-03-01

Structuring by laser remelting enables completely new possibilities for designing surfaces since material is redistributed but not wasted. In addition to technological advantages, cost and time benefits yield from shortened process times, the avoidance of harmful chemicals and the elimination of subsequent finishing steps such as cleaning and polishing. The functional principle requires a completely new optical machine technology that maintains the spatial and temporal superposition and manipulation of three different laser beams emitted from two laser sources of different wavelength. The optical system has already been developed and demonstrated for the processing of flat samples of hot and cold working steel. However, since particularly the structuring of 3D-injection molds represents an application example of high innovation potential, the optical system has to take into account the elliptical beam geometry that occurs when the laser beams irradiate a curved surface. To take full advantage of structuring by remelting for the processing of 3D surfaces, additional optical functionality, called EPS (elliptical pre-shaping) has to be integrated into the existing set-up. The development of the beam shaping devices not only requires the analysis of the mechanisms of the beam projection but also a suitable optical design. Both aspects are discussed in this paper.

Growth media in anaerobic fermentative processes: The underestimated potential of thermophilic fermentation and anaerobic digestion.

PubMed

Hendriks, A T W M; van Lier, J B; de Kreuk, M K

Fermentation and anaerobic digestion of organic waste and wastewater is broadly studied and applied. Despite widely available results and data for these processes, comparison of the generated results in literature is difficult. Not only due to the used variety of process conditions, but also because of the many different growth media that are used. Composition of growth media can influence biogas production (rates) and lead to process instability during anaerobic digestion. To be able to compare results of the different studies reported, and to ensure nutrient limitation is not influencing observations ascribed to process dynamics and/or reaction kinetics, a standard protocol for creating a defined growth medium for anaerobic digestion and mixed culture fermentation is proposed. This paper explains the role(s) of the different macro- and micronutrients, as well as the choices for a growth medium formulation strategy. In addition, the differences in nutrient requirements between mesophilic and thermophilic systems are discussed as well as the importance of specific trace metals regarding specific conversion routes and the possible supplementary requirement of vitamins. The paper will also give some insight into the bio-availability and toxicity of trace metals. A remarkable finding is that mesophilic and thermophilic enzymes are quite comparable at their optimum temperatures. This has consequences for the trace metal requirements of thermophiles under certain conditions. Under non-limiting conditions, the trace metal requirement of thermophilic systems is about 3 times higher than for mesophilic systems. Copyright © 2017 Elsevier Inc. All rights reserved.

Suboptimal distributed control and estimation: application to a four coupled tanks system

NASA Astrophysics Data System (ADS)

Orihuela, Luis; Millán, Pablo; Vivas, Carlos; Rubio, Francisco R.

2016-06-01

The paper proposes an innovative estimation and control scheme that enables the distributed monitoring and control of large-scale processes. The proposed approach considers a discrete linear time-invariant process controlled by a network of agents that may both collect information about the evolution of the plant and apply control actions to drive its behaviour. The problem makes full sense when local observability/controllability is not assumed and the communication between agents can be exploited to reach system-wide goals. Additionally, to reduce agents bandwidth requirements and power consumption, an event-based communication policy is studied. The design procedure guarantees system stability, allowing the designer to trade-off performance, control effort and communication requirements. The obtained controllers and observers are implemented in a fully distributed fashion. To illustrate the performance of the proposed technique, experimental results on a quadruple-tank process are provided.

Production of gluten and germ by ethanol fermentation of raw corn

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1987-01-01

The Illinois ethanol fuel industry has grown to be an important part of our state's economy over the past 10 years. It provides an additional market for Illinois' abundant corn production, provides many industrial jobs, and substitutes a home-grown renewable energy resource for imported oil. More than 30 percent of all gasoline sold in Illinois contains 10 percent ethanol. The economics of producing ethanol from corn is strongly affected by the byproduct value and by the energy required in the production process. This document reports on efforts to research a new microbial process that would improve the ethanol fermentation processmore » in both these areas. The new process allows direct fermentation of corn starch to ethanol without the usual requirement of cooking the corn. This reduces the amount of energy needed for production and recovers the protein-containing gluten and oil-containing germ with all of the original food value intact.« less

Age-dependent impairment of auditory processing under spatially focused and divided attention: an electrophysiological study.

PubMed

Wild-Wall, Nele; Falkenstein, Michael

2010-01-01

By using event-related potentials (ERPs) the present study examines if age-related differences in preparation and processing especially emerge during divided attention. Binaurally presented auditory cues called for focused (valid and invalid) or divided attention to one or both ears. Responses were required to subsequent monaurally presented valid targets (vowels), but had to be suppressed to non-target vowels or invalidly cued vowels. Middle-aged participants were more impaired under divided attention than young ones, likely due to an age-related decline in preparatory attention following cues as was reflected in a decreased CNV. Under divided attention, target processing was increased in the middle-aged, likely reflecting compensatory effort to fulfill task requirements in the difficult condition. Additionally, middle-aged participants processed invalidly cued stimuli more intensely as was reflected by stimulus ERPs. The results suggest an age-related impairment in attentional preparation after auditory cues especially under divided attention and latent difficulties to suppress irrelevant information.

A hybrid life cycle inventory of nano-scale semiconductor manufacturing.

PubMed

Krishnan, Nikhil; Boyd, Sarah; Somani, Ajay; Raoux, Sebastien; Clark, Daniel; Dornfeld, David

2008-04-15

The manufacturing of modern semiconductor devices involves a complex set of nanoscale fabrication processes that are energy and resource intensive, and generate significant waste. It is important to understand and reduce the environmental impacts of semiconductor manufacturing because these devices are ubiquitous components in electronics. Furthermore, the fabrication processes used in the semiconductor industry are finding increasing application in other products, such as microelectromechanical systems (MEMS), flat panel displays, and photovoltaics. In this work we develop a library of typical gate-to-gate materials and energy requirements, as well as emissions associated with a complete set of fabrication process models used in manufacturing a modern microprocessor. In addition, we evaluate upstream energy requirements associated with chemicals and materials using both existing process life cycle assessment (LCA) databases and an economic input-output (EIO) model. The result is a comprehensive data set and methodology that may be used to estimate and improve the environmental performance of a broad range of electronics and other emerging applications that involve nano and micro fabrication.

2D modeling of direct laser metal deposition process using a finite particle method

NASA Astrophysics Data System (ADS)

Anedaf, T.; Abbès, B.; Abbès, F.; Li, Y. M.

2018-05-01

Direct laser metal deposition is one of the material additive manufacturing processes used to produce complex metallic parts. A thorough understanding of the underlying physical phenomena is required to obtain a high-quality parts. In this work, a mathematical model is presented to simulate the coaxial laser direct deposition process tacking into account of mass addition, heat transfer, and fluid flow with free surface and melting. The fluid flow in the melt pool together with mass and energy balances are solved using the Computational Fluid Dynamics (CFD) software NOGRID-points, based on the meshless Finite Pointset Method (FPM). The basis of the computations is a point cloud, which represents the continuum fluid domain. Each finite point carries all fluid information (density, velocity, pressure and temperature). The dynamic shape of the molten zone is explicitly described by the point cloud. The proposed model is used to simulate a single layer cladding.

Real-time spectral characterization of a photon pair source using a chirped supercontinuum seed.

PubMed

Erskine, Jennifer; England, Duncan; Kupchak, Connor; Sussman, Benjamin

2018-02-15

Photon pair sources have wide ranging applications in a variety of quantum photonic experiments and protocols. Many of these protocols require well controlled spectral correlations between the two output photons. However, due to low cross-sections, measuring the joint spectral properties of photon pair sources has historically been a challenging and time-consuming task. Here, we present an approach for the real-time measurement of the joint spectral properties of a fiber-based four wave mixing source. We seed the four wave mixing process using a broadband chirped pulse, studying the stimulated process to extract information regarding the spontaneous process. In addition, we compare stimulated emission measurements with the spontaneous process to confirm the technique's validity. Joint spectral measurements have taken many hours historically and several minutes with recent techniques. Here, measurements have been demonstrated in 5-30 s depending on resolution, offering substantial improvement. Additional benefits of this approach include flexible resolution, large measurement bandwidth, and reduced experimental overhead.

Method for materials deposition by ablation transfer processing

DOEpatents

Weiner, Kurt H.

1996-01-01

A method in which a thin layer of semiconducting, insulating, or metallic material is transferred by ablation from a source substrate, coated uniformly with a thin layer of said material, to a target substrate, where said material is desired, with a pulsed, high intensity, patternable beam of energy. The use of a patternable beam allows area-selective ablation from the source substrate resulting in additive deposition of the material onto the target substrate which may require a very low percentage of the area to be covered. Since material is placed only where it is required, material waste can be minimized by reusing the source substrate for depositions on multiple target substrates. Due to the use of a pulsed, high intensity energy source the target substrate remains at low temperature during the process, and thus low-temperature, low cost transparent glass or plastic can be used as the target substrate. The method can be carried out atmospheric pressures and at room temperatures, thus eliminating vacuum systems normally required in materials deposition processes. This invention has particular application in the flat panel display industry, as well as minimizing materials waste and associated costs.

A Portable Surface Contamination Monitor Based on the Principle of Optically Stimulated Electron Emission (OSEE)

NASA Technical Reports Server (NTRS)

Perey, D. F.

1996-01-01

Many industrial and aerospace processes involving the joining of materials, require sufficient surface cleanliness to insure proper bonding. Processes as diverse as painting, welding, or the soldering of electronic circuits will be compromised if prior inspection and removal of surface contaminants is inadequate. As process requirements become more stringent and the number of different materials and identified contaminants increases, various instruments and techniques have been developed for improved inspection. One such technique, based on the principle of Optically Stimulated Electron Emission (OSEE), has been explored for a number of years as a tool for surface contamination monitoring. Some of the benefits of OSEE are: it is non-contacting; requires little operator training; and has very high contamination sensitivity. This paper describes the development of a portable OSEE based surface contamination monitor. The instrument is suitable for both hand-held and robotic inspections with either manual or automated control of instrument operation. In addition, instrument output data is visually displayed to the operator and may be sent to an external computer for archiving or analysis.

Business Process Modelling is an Essential Part of a Requirements Analysis. Contribution of EFMI Primary Care Working Group.

PubMed

de Lusignan, S; Krause, P; Michalakidis, G; Vicente, M Tristan; Thompson, S; McGilchrist, M; Sullivan, F; van Royen, P; Agreus, L; Desombre, T; Taweel, A; Delaney, B

2012-01-01

To perform a requirements analysis of the barriers to conducting research linking of primary care, genetic and cancer data. We extended our initial data-centric approach to include socio-cultural and business requirements. We created reference models of core data requirements common to most studies using unified modelling language (UML), dataflow diagrams (DFD) and business process modelling notation (BPMN). We conducted a stakeholder analysis and constructed DFD and UML diagrams for use cases based on simulated research studies. We used research output as a sensitivity analysis. Differences between the reference model and use cases identified study specific data requirements. The stakeholder analysis identified: tensions, changes in specification, some indifference from data providers and enthusiastic informaticians urging inclusion of socio-cultural context. We identified requirements to collect information at three levels: micro- data items, which need to be semantically interoperable, meso- the medical record and data extraction, and macro- the health system and socio-cultural issues. BPMN clarified complex business requirements among data providers and vendors; and additional geographical requirements for patients to be represented in both linked datasets. High quality research output was the norm for most repositories. Reference models provide high-level schemata of the core data requirements. However, business requirements' modelling identifies stakeholder issues and identifies what needs to be addressed to enable participation.

Automated and Scalable Data Reduction in the textsc{Sofia} Data Processing System

NASA Astrophysics Data System (ADS)

Krzaczek, R.; Shuping, R.; Charcos-Llorens, M.; Alles, R.; Vacca, W.

2015-09-01

In order to provide suitable data products to general investigators and other end users in a timely manner, the Stratospheric Observatory for Infrared Astronomy SOFIA) has developed a framework supporting the automated execution of data processing pipelines for the various instruments, called the Data Processing System (DPS), see Shuping et al. (2014) for overview). The primary requirement is to process all data collected from a flight within eight hours, allowing data quality assessments and inspections to be made the following day. The raw data collected during a flight requires processing by a number of different software packages and tools unique to each combination of instrument and mode of operation, much of it developed in-house, in order to create data products for use by investigators and other end-users. The requirement to deliver these data products in a consistent, predictable, and performant manner presents a significant challenge for the observatory. Herein we present aspects of the DPS that help to achieve these goals. We discuss how it supports data reduction software written in a variety of languages and environments, its support for new versions and live upgrades to that software and other necessary resources (e.g., calibrations), its accommodation of sudden processing loads through the addition (and eventual removal) of computing resources, and close with an observation of the performance achieved in the first two observing cycles of SOFIA.

Preliminary results from the High Speed Airframe Integration Research project

NASA Technical Reports Server (NTRS)

Coen, Peter G.; Sobieszczanski-Sobieski, Jaroslaw; Dollyhigh, Samuel M.

1992-01-01

A review is presented of the accomplishment of the near term objectives of developing an analysis system and optimization methods during the first year of the NASA Langley High Speed Airframe Integration Research (HiSAIR) project. The characteristics of a Mach 3 HSCT transport have been analyzed utilizing the newly developed process. In addition to showing more detailed information about the aerodynamic and structural coupling for this type of vehicle, this exercise aided in further refining the data requirements for the analysis process.

Graph Unification and Tangram Hypothesis Explanation Representation (GATHER) and System and Component Modeling Framework (SCMF)

DTIC Science & Technology

2008-08-01

services, DIDS and DMS, are deployable on the TanGrid system and are accessible via two APIs, a Java client and a servlet based interface. Additionally...but required the user to instantiate an IGraph object with several Java Maps containing the nodes, node attributes, edge types, and the connections...restrictions imposed by the bulk ingest process. Finally, once the bulk ingest process was available in the GraphUnification Java Archives (JAR), DC was

Recent advances in phase shifted time averaging and stroboscopic interferometry

NASA Astrophysics Data System (ADS)

Styk, Adam; Józwik, Michał

2016-08-01

Classical Time Averaging and Stroboscopic Interferometry are widely used for MEMS/MOEMS dynamic behavior investigations. Unfortunately both methods require an extensive measurement and data processing strategies in order to evaluate the information on maximum amplitude at a given load of vibrating object. In this paper the modified strategies of data processing in both techniques are introduced. These modifications allow for fast and reliable calculation of searched value, without additional complication of measurement systems. Through the paper the both approaches are discussed and experimentally verified.

Level 1 remedial investigation work plan, 300 Area Process Ponds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This report discusses the objectives of the site characterization for the 300 Area Process Ponds which are to identify and quantify contamination at the ponds and to estimate their potential impact on human health and the environment. The results of the site characterization will be used to identify any future actions related to contamination at the site and to identify any additional data requirements needed to support selection of a remedial action. 9 refs., 12 figs., 8 tabs.

Optical fiber technology for space: challenges of development and qualification

NASA Astrophysics Data System (ADS)

Goepel, Michael

2017-11-01

Using fiber optical components and assemblies for space flight applications brings several challenges for the design and the qualification process. Good knowledge of the system and environmental requirements is needed to derive design decisions and select suitable components for the fiber optical subsystem. Furthermore, the manufacturing process and integration limitations are providing additional constraints, which have to be considered at the beginning of the design phase. Besides Commercial off the shelf (COTS) components, custom made parts are often necessary.

The Prospects of Accounting at Mining Enterprises as a Factor of Ensuring their Sustainable Development

NASA Astrophysics Data System (ADS)

Tyuleneva, Tatiana

2017-11-01

One of the problems of sustainable development of mining companies is attracting additional investment. To solve it requires access to international capital markets, in this context, enterprises need to prepare financial statements with international requirements based on the data generated by the accounting system. The article considers the basic problems of accounting in the extractive industries due to the nature of the industry, as well as evaluation of the completeness of their solution in the framework of international financial reporting standards. In addition, lists the characteristics of accounting for mining industry, due to the peculiarities of the production process that need to be considered to solve these problems. This sector is extremely important for individual countries and on a global scale.

Droplet-Based Segregation and Extraction of Concentrated Samples

DOE Office of Scientific and Technical Information (OSTI.GOV)

Buie, C R; Buckley, P; Hamilton, J

2007-02-23

Microfluidic analysis often requires sample concentration and separation techniques to isolate and detect analytes of interest. Complex or scarce samples may also require an orthogonal separation and detection method or off-chip analysis to confirm results. To perform these additional steps, the concentrated sample plug must be extracted from the primary microfluidic channel with minimal sample loss and dilution. We investigated two extraction techniques; injection of immiscible fluid droplets into the sample stream (''capping'''') and injection of the sample into an immiscible fluid stream (''extraction''). From our results we conclude that capping is the more effective partitioning technique. Furthermore, this functionalitymore » enables additional off-chip post-processing procedures such as DNA/RNA microarray analysis, realtime polymerase chain reaction (RT-PCR), and culture growth to validate chip performance.« less

Controller design for wind turbine load reduction via multiobjective parameter synthesis

NASA Astrophysics Data System (ADS)

Hoffmann, A. F.; Weiβ, F. A.

2016-09-01

During the design process for a wind turbine load reduction controller many different, sometimes conflicting requirements must be fulfilled simultaneously. If the requirements can be expressed as mathematical criteria, such a design problem can be solved by a criterion-vector and multi-objective design optimization. The software environment MOPS (Multi-Objective Parameter Synthesis) supports the engineer for such a design optimization. In this paper MOPS is applied to design a multi-objective load reduction controller for the well-known DTU 10 MW reference wind turbine. A significant reduction in the fatigue criteria especially the blade damage can be reached by the use of an additional Individual Pitch Controller (IPC) and an additional tower damper. This reduction is reached as a trade-off with an increase of actuator load.

New techniques for experimental generation of two-dimensional blade-vortex interaction at low Reynolds numbers

NASA Technical Reports Server (NTRS)

Booth, E., Jr.; Yu, J. C.

1986-01-01

An experimental investigation of two dimensional blade vortex interaction was held at NASA Langley Research Center. The first phase was a flow visualization study to document the approach process of a two dimensional vortex as it encountered a loaded blade model. To accomplish the flow visualization study, a method for generating two dimensional vortex filaments was required. The numerical study used to define a new vortex generation process and the use of this process in the flow visualization study were documented. Additionally, photographic techniques and data analysis methods used in the flow visualization study are examined.

Intelligent Processing Equipment Within the Environmental Protection Agency

NASA Technical Reports Server (NTRS)

Greathouse, Daniel G.; Nalesnik, Richard P.

1992-01-01

Protection of the environment and environmental remediation requires the cooperation, at all levels, of government and industry. Intelligent processing equipment, in addition to other artificial intelligence based tools, was used by the Environmental Protection Agency to provide personnel safety and improve the efficiency of those responsible for protection and remediation of the environment. These exploratory efforts demonstrate the feasibility and utility of expanding development and widespread use of these tools. A survey of current intelligent processing equipment applications in the Agency is presented and is followed by a brief discussion of possible uses in the future.

Affinity+: Semi-Structured Brainstorming on Large Displays

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burtner, Edwin R.; May, Richard A.; Scarberry, Randall E.

2013-04-27

Affinity diagraming is a powerful method for encouraging and capturing lateral thinking in a group environment. The Affinity+ Concept was designed to improve the collaborative brainstorm process through the use of large display surfaces in conjunction with mobile devices like smart phones and tablets. The system works by capturing the ideas digitally and allowing users to sort and group them on a large touch screen manually. Additionally, Affinity+ incorporates theme detection, topic clustering, and other processing algorithms that help bring structured analytic techniques to the process without requiring explicit leadership roles and other overhead typically involved in these activities.

Crystal growth in a low gravity environment

NASA Technical Reports Server (NTRS)

Carruthers, J. R.

1977-01-01

Crystal growth in microgravity possesses several distinct technological advantages over earth-bound processes; containerless handling and reduction of density gradient driven as well as sedimentation flows. Experiments performed in space to date have been basically reproductions of processes currently used on earth and the results have clarified our understanding of crystal growth dynamics. In addition, both unresolved problems and areas requiring further study on earth have been identified. Future work in space processing of materials must address these areas of study as soon as possible if the full potential of a space environment to develop new techniques and materials is to be realized.

Screening Methodologies to Support Risk and Technology ...

EPA Pesticide Factsheets

The Clean Air Act establishes a two-stage regulatory process for addressing emissions of hazardous air pollutants (HAPs) from stationary sources. In the first stage, the Act requires the EPA to develop technology-based standards for categories of industrial sources. We have largely completed the required “Maximum Achievable Control Technology” (MACT) standards. In the second stage of the regulatory process, EPA must review each MACT standard at least every eight years and revise them as necessary, “taking into account developments in practices, processes and control technologies.” We call this requirement the “technology review.” EPA is also required to complete a one-time assessment of the health and environmental risks that remain after sources come into compliance with MACT. This residual risk review also must be done within 8 years of setting the initial MACT standard. If additional risk reductions are necessary to protect public health with an ample margin of safety or to prevent adverse environmental effects, EPA must develop standards to address these remaining risks. Because the risk review is an important component of the RTR process, EPA is seeking SAB input on the scientific credibility of specific enhancements made to our risk assessment methodologies, particularly with respect to screening methodologies, since the last SAB review was completed in 2010. These enhancements to our risk methodologies are outlined in the document title

Effect of calcium formate as an additive on desulfurization in power plants.

PubMed

Li, Zhenhua; Xie, Chunfang; Lv, Jing; Zhai, Ruiguo

2018-05-01

SO 2 in flue gas needs to be eliminated to alleviate air pollution. As the quality of coal decreases and environmental standard requirements become more stringent, the high-efficiency desulfurization of flue gas faces more and more challenges. As an economical and environmentally friendly solution, the effect of calcium formate as an additive on desulfurization efficiency in the wet flue gas desulfurization (WFGD) process was studied for the first time. Improvement of the desulfurization efficiency was achieved with limited change in pH after calcium formate was added into the reactor, and it was found to work better than other additives tested. The positive effects were further verified in a power plant, which showed that adding calcium formate could promote the dissolution of calcium carbonate, accelerate the growth of gypsum crystals and improve the efficiency of desulfurization. Thus, calcium formate was proved to be an effective additive and can potentially be used to reduce the amount of limestone slurry required, as well as the energy consumption and operating costs in industrial desulfurization. Copyright © 2017. Published by Elsevier B.V.

Requirements Development for the NASA Advanced Engineering Environment (AEE)

NASA Technical Reports Server (NTRS)

Rogers, Eric; Hale, Joseph P.; Zook, Keith; Gowda, Sanjay; Salas, Andrea O.

2003-01-01

The requirements development process for the Advanced Engineering Environment (AEE) is presented. This environment has been developed to allow NASA to perform independent analysis and design of space transportation architectures and technologies. Given the highly collaborative and distributed nature of AEE, a variety of organizations are involved in the development, operations and management of the system. Furthermore, there are additional organizations involved representing external customers and stakeholders. Thorough coordination and effective communication is essential to translate desired expectations of the system into requirements. Functional, verifiable requirements for this (and indeed any) system are necessary to fulfill several roles. Requirements serve as a contractual tool, configuration management tool, and as an engineering tool, sometimes simultaneously. The role of requirements as an engineering tool is particularly important because a stable set of requirements for a system provides a common framework of system scope and characterization among team members. Furthermore, the requirements provide the basis for checking completion of system elements and form the basis for system verification. Requirements are at the core of systems engineering. The AEE Project has undertaken a thorough process to translate the desires and expectations of external customers and stakeholders into functional system-level requirements that are captured with sufficient rigor to allow development planning, resource allocation and system-level design, development, implementation and verification. These requirements are maintained in an integrated, relational database that provides traceability to governing Program requirements and also to verification methods and subsystem-level requirements.

Final Technical Report - Advanced Optical Sensors to Minimize Energy Consumption in Polymer Extrusion Processes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Susan J. Foulk

Project Objective: The objectives of this study are to develop an accurate and stable on-line sensor system to monitor color and composition on-line in polymer melts, to develop a scheme for using the output to control extruders to eliminate the energy, material and operational costs of off-specification product, and to combine or eliminate some extrusion processes. Background: Polymer extrusion processes are difficult to control because the quality achieved in the final product is complexly affected by the properties of the extruder screw, speed of extrusion, temperature, polymer composition, strength and dispersion properties of additives, and feeder system properties. Extruder systemsmore » are engineered to be highly reproducible so that when the correct settings to produce a particular product are found, that product can be reliably produced time after time. However market conditions often require changes in the final product, different products or grades may be processed in the same equipment, and feed materials vary from lot to lot. All of these changes require empirical adjustment of extruder settings to produce a product meeting specifications. Optical sensor systems that can continuously monitor the composition and color of the extruded polymer could detect process upsets, drift, blending oscillations, and changes in dispersion of additives. Development of an effective control algorithm using the output of the monitor would enable rapid corrections for changes in materials and operating conditions, thereby eliminating most of the scrap and recycle of current processing. This information could be used to identify extruder systems issues, diagnose problem sources, and suggest corrective actions in real-time to help keep extruder system settings within the optimum control region. Using these advanced optical sensor systems would give extruder operators real-time feedback from their process. They could reduce the amount of off-spec product produced and significantly reduce energy consumption. Also, because blending and dispersion of additives and components in the final product could be continuously verified, we believe that, in many cases, intermediate compounding steps could be eliminated (saving even more time and energy).« less

Processing speed and working memory span: their differential role in superficial and deep memory processes in schizophrenia.

PubMed

Brébion, Gildas; Bressan, Rodrigo A; Pilowsky, Lyn S; David, Anthony S

2011-05-01

Previous work has suggested that decrement in both processing speed and working memory span plays a role in the memory impairment observed in patients with schizophrenia. We undertook a study to examine simultaneously the effect of these two factors. A sample of 49 patients with schizophrenia and 43 healthy controls underwent a battery of verbal and visual memory tasks. Superficial and deep encoding memory measures were tallied. We conducted regression analyses on the various memory measures, using processing speed and working memory span as independent variables. In the patient group, processing speed was a significant predictor of superficial and deep memory measures in verbal and visual memory. Working memory span was an additional significant predictor of the deep memory measures only. Regression analyses involving all participants revealed that the effect of diagnosis on all the deep encoding memory measures was reduced to non-significance when processing speed was entered in the regression. Decreased processing speed is involved in verbal and visual memory deficit in patients, whether the task require superficial or deep encoding. Working memory is involved only insofar as the task requires a certain amount of effort.

Tunable solvation effects on the size-selective fractionation of metal nanoparticles in CO2 gas-expanded solvents.

PubMed

Anand, Madhu; McLeod, M Chandler; Bell, Philip W; Roberts, Christopher B

2005-12-08

This paper presents an environmentally friendly, inexpensive, rapid, and efficient process for size-selective fractionation of polydisperse metal nanoparticle dispersions into multiple narrow size populations. The dispersibility of ligand-stabilized silver and gold nanoparticles is controlled by altering the ligand tails-solvent interaction (solvation) by the addition of carbon dioxide (CO2) gas as an antisolvent, thereby tailoring the bulk solvent strength. This is accomplished by adjusting the CO2 pressure over the liquid, resulting in a simple means to tune the nanoparticle precipitation by size. This study also details the influence of various factors on the size-separation process, such as the types of metal, ligand, and solvent, as well as the use of recursive fractionation and the time allowed for settling during each fractionation step. The pressure range required for the precipitation process is the same for both the silver and gold particles capped with dodecanethiol ligands. A change in ligand or solvent length has an effect on the interaction between the solvent and the ligand tails and therefore the pressure range required for precipitation. Stronger interactions between solvent and ligand tails require greater CO2 pressure to precipitate the particles. Temperature is another variable that impacts the dispersibility of the nanoparticles through changes in the density and the mole fraction of CO2 in the gas-expanded liquids. Recursive fractionation for a given system within a particular pressure range (solvent strength) further reduces the polydispersity of the fraction obtained within that pressure range. Specifically, this work utilizes the highly tunable solvent properties of organic/CO2 solvent mixtures to selectively size-separate dispersions of polydisperse nanoparticles (2 to 12 nm) into more monodisperse fractions (+/-2 nm). In addition to providing efficient separation of the particles, this process also allows all of the solvent and antisolvent to be recovered, thereby rendering it a green solvent process.

SLS Navigation Model-Based Design Approach

NASA Technical Reports Server (NTRS)

Oliver, T. Emerson; Anzalone, Evan; Geohagan, Kevin; Bernard, Bill; Park, Thomas

2018-01-01

The SLS Program chose to implement a Model-based Design and Model-based Requirements approach for managing component design information and system requirements. This approach differs from previous large-scale design efforts at Marshall Space Flight Center where design documentation alone conveyed information required for vehicle design and analysis and where extensive requirements sets were used to scope and constrain the design. The SLS Navigation Team has been responsible for the Program-controlled Design Math Models (DMMs) which describe and represent the performance of the Inertial Navigation System (INS) and the Rate Gyro Assemblies (RGAs) used by Guidance, Navigation, and Controls (GN&C). The SLS Navigation Team is also responsible for the navigation algorithms. The navigation algorithms are delivered for implementation on the flight hardware as a DMM. For the SLS Block 1-B design, the additional GPS Receiver hardware is managed as a DMM at the vehicle design level. This paper provides a discussion of the processes and methods used to engineer, design, and coordinate engineering trades and performance assessments using SLS practices as applied to the GN&C system, with a particular focus on the Navigation components. These include composing system requirements, requirements verification, model development, model verification and validation, and modeling and analysis approaches. The Model-based Design and Requirements approach does not reduce the effort associated with the design process versus previous processes used at Marshall Space Flight Center. Instead, the approach takes advantage of overlap between the requirements development and management process, and the design and analysis process by efficiently combining the control (i.e. the requirement) and the design mechanisms. The design mechanism is the representation of the component behavior and performance in design and analysis tools. The focus in the early design process shifts from the development and management of design requirements to the development of usable models, model requirements, and model verification and validation efforts. The models themselves are represented in C/C++ code and accompanying data files. Under the idealized process, potential ambiguity in specification is reduced because the model must be implementable versus a requirement which is not necessarily subject to this constraint. Further, the models are shown to emulate the hardware during validation. For models developed by the Navigation Team, a common interface/standalone environment was developed. The common environment allows for easy implementation in design and analysis tools. Mechanisms such as unit test cases ensure implementation as the developer intended. The model verification and validation process provides a very high level of component design insight. The origin and implementation of the SLS variant of Model-based Design is described from the perspective of the SLS Navigation Team. The format of the models and the requirements are described. The Model-based Design approach has many benefits but is not without potential complications. Key lessons learned associated with the implementation of the Model Based Design approach and process from infancy to verification and certification are discussed

Visual processing in reading disorders and attention-deficit/hyperactivity disorder and its contribution to basic reading ability

PubMed Central

Kibby, Michelle Y.; Dyer, Sarah M.; Vadnais, Sarah A.; Jagger, Audreyana C.; Casher, Gabriel A.; Stacy, Maria

2015-01-01

Whether visual processing deficits are common in reading disorders (RD), and related to reading ability in general, has been debated for decades. The type of visual processing affected also is debated, although visual discrimination and short-term memory (STM) may be more commonly related to reading ability. Reading disorders are frequently comorbid with ADHD, and children with ADHD often have subclinical reading problems. Hence, children with ADHD were used as a comparison group in this study. ADHD and RD may be dissociated in terms of visual processing. Whereas RD may be associated with deficits in visual discrimination and STM for order, ADHD is associated with deficits in visual-spatial processing. Thus, we hypothesized that children with RD would perform worse than controls and children with ADHD only on a measure of visual discrimination and a measure of visual STM that requires memory for order. We expected all groups would perform comparably on the measure of visual STM that does not require sequential processing. We found children with RD or ADHD were commensurate to controls on measures of visual discrimination and visual STM that do not require sequential processing. In contrast, both RD groups (RD, RD/ADHD) performed worse than controls on the measure of visual STM that requires memory for order, and children with comorbid RD/ADHD performed worse than those with ADHD. In addition, of the three visual measures, only sequential visual STM predicted reading ability. Hence, our findings suggest there is a deficit in visual sequential STM that is specific to RD and is related to basic reading ability. The source of this deficit is worthy of further research, but it may include both reduced memory for order and poorer verbal mediation. PMID:26579020

Visual processing in reading disorders and attention-deficit/hyperactivity disorder and its contribution to basic reading ability.

PubMed

Kibby, Michelle Y; Dyer, Sarah M; Vadnais, Sarah A; Jagger, Audreyana C; Casher, Gabriel A; Stacy, Maria

2015-01-01

Whether visual processing deficits are common in reading disorders (RD), and related to reading ability in general, has been debated for decades. The type of visual processing affected also is debated, although visual discrimination and short-term memory (STM) may be more commonly related to reading ability. Reading disorders are frequently comorbid with ADHD, and children with ADHD often have subclinical reading problems. Hence, children with ADHD were used as a comparison group in this study. ADHD and RD may be dissociated in terms of visual processing. Whereas RD may be associated with deficits in visual discrimination and STM for order, ADHD is associated with deficits in visual-spatial processing. Thus, we hypothesized that children with RD would perform worse than controls and children with ADHD only on a measure of visual discrimination and a measure of visual STM that requires memory for order. We expected all groups would perform comparably on the measure of visual STM that does not require sequential processing. We found children with RD or ADHD were commensurate to controls on measures of visual discrimination and visual STM that do not require sequential processing. In contrast, both RD groups (RD, RD/ADHD) performed worse than controls on the measure of visual STM that requires memory for order, and children with comorbid RD/ADHD performed worse than those with ADHD. In addition, of the three visual measures, only sequential visual STM predicted reading ability. Hence, our findings suggest there is a deficit in visual sequential STM that is specific to RD and is related to basic reading ability. The source of this deficit is worthy of further research, but it may include both reduced memory for order and poorer verbal mediation.

Preferential depletion of zinc within Costa Rica upwelling dome creates conditions for zinc co-limitation of primary production

PubMed Central

Dreux Chappell, P.; Vedmati, Jagruti; Selph, Karen E.; Cyr, Heather A.; Jenkins, Bethany D.; Landry, Michael R.; Moffett, James W.

2016-01-01

The Costa Rica Dome (CRD) is a wind-driven feature characterized by high primary production and an unusual cyanobacterial bloom in surface waters. It is not clear whether this bloom arises from top-down or bottom-up processes. Several studies have argued that trace metal geochemistry within the CRD contributes to the composition of the phytoplankton assemblages, since cyanobacteria and eukaryotic phytoplankton have different transition metal requirements. Here, we report that total dissolved zinc (Zn) is significantly depleted relative to phosphate (P) and silicate (Si) within the upper water column of the CRD compared with other oceanic systems, and this may create conditions favorable for cyanobacteria, which have lower Zn requirements than their eukaryotic competitors. Shipboard grow-out experiments revealed that while Si was a limiting factor under our experimental conditions, additions of Si and either iron (Fe) or Zn led to higher biomass than Si additions alone. The addition of Fe and Zn alone did not lead to significant enhancements. Our results suggest that the depletion of Zn relative to P in upwelled waters may create conditions in the near-surface waters that favor phytoplankton with low Zn requirements, including cyanobacteria. PMID:27275028

Material requirements for the High Speed Civil Transport

NASA Technical Reports Server (NTRS)

Stephens, Joseph R.; Hecht, Ralph J.; Johnson, Andrew M.

1993-01-01

Under NASA-sponsored High Speed Research (HSR) programs, the materials and processing requirements have been identified for overcoming the environmental and economic barriers of the next generation High Speed Civil Transport (HSCT) propulsion system. The long (2 to 5 hours) supersonic cruise portion of the HSCT cycle will place additional durability requirements on all hot section engine components. Low emissions combustor designs will require high temperature ceramic matrix composite liners to meet an emission goal of less than 5g NO(x) per Kg fuel burned. Large axisymmetric and two-dimensional exhaust nozzle designs are now under development to meet or exceed FAR 36 Stage III noise requirements, and will require lightweight, high temperature metallic, intermetallic, and ceramic matrix composites to reduce nozzle weight and meet structural and acoustic component performance goals. This paper describes and discusses the turbomachinery, combustor, and exhaust nozzle requirements of the High Speed Civil Transport propulsion system.

Application of advanced diffraction based optical metrology overlay capabilities for high-volume manufacturing

NASA Astrophysics Data System (ADS)

Chen, Kai-Hsiung; Huang, Guo-Tsai; Hsieh, Hung-Chih; Ni, Wei-Feng; Chuang, S. M.; Chuang, T. K.; Ke, Chih-Ming; Huang, Jacky; Rao, Shiuan-An; Cumurcu Gysen, Aysegul; d'Alfonso, Maxime; Yueh, Jenny; Izikson, Pavel; Soco, Aileen; Wu, Jon; Nooitgedagt, Tjitte; Ottens, Jeroen; Kim, Yong Ho; Ebert, Martin

2017-03-01

On-product overlay requirements are becoming more challenging with every next technology node due to the continued decrease of the device dimensions and process tolerances. Therefore, current and future technology nodes require demanding metrology capabilities such as target designs that are robust towards process variations and high overlay measurement density (e.g. for higher order process corrections) to enable advanced process control solutions. The impact of advanced control solutions based on YieldStar overlay data is being presented in this paper. Multi patterning techniques are applied for critical layers and leading to additional overlay measurement demands. The use of 1D process steps results in the need of overlay measurements relative to more than one layer. Dealing with the increased number of overlay measurements while keeping the high measurement density and metrology accuracy at the same time presents a challenge for high volume manufacturing (HVM). These challenges are addressed by the capability to measure multi-layer targets with the recently introduced YieldStar metrology tool, YS350. On-product overlay results of such multi-layers and standard targets are presented including measurement stability performance.

Development of a water-jet assisted laser paint removal process

NASA Astrophysics Data System (ADS)

Madhukar, Yuvraj K.; Mullick, Suvradip; Nath, Ashish K.

2013-12-01

The laser paint removal process usually leaves behind traces of combustion product i.e. ashes on the surface. An additional post-processing such as light-brushing or wiping by some mechanical means is required to remove the residual ash. In order to strip out the paint completely from the surface in a single step, a water-jet assisted laser paint removal process has been investigated. The 1.07 μm wavelength of Yb-fiber laser radiation has low absorption in water; therefore a high power fiber laser was used in the experiment. The laser beam was delivered on the paint-surface along with a water jet to remove the paint and residual ashes effectively. The specific energy, defined as the laser energy required removing a unit volume of paint was found to be marginally more than that for the gas-jet assisted laser paint removal process. However, complete paint removal was achieved with the water-jet assist only. The relatively higher specific energy in case of water-jet assist is mainly due to the scattering of laser beam in the turbulent flow of water-jet.

PF-WFS Shell Inspection Update December 2016

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vigil, Anthony Eugene; Ledoux, Reina Rebecca; Gonzales, Antonio R.

Since the last project update in FY16:Q2, PF-WFS personnel have advanced in understanding of shell inspection on Coordinate Measuring Machines {CMM} and refined the PF-WFS process to the point it was decided to convert shell inspection from the Sheffield #1 gage to Lietz CM Ms. As a part of introspection on the quality of this process many sets of data have been reviewed and analyzed. This analysis included Sheffield to CMM comparisons, CMM inspection repeatability, fixturing differences, quality check development, probing approach changes. This update report will touch on these improvements that have built the confidence in this process tomore » mainstream it inspecting shells. In addition to the CMM programming advancements, the continuation in refinement of input and outputs for the CMM program has created an archiving scheme, input spline files, an output metafile, and inspection report package. This project will continue to mature. Part designs may require program modifications to accommodate "new to this process" part designs. Technology limitations tied to security and performance are requiring possible changes to computer configurations to support an automated process.« less

Data Processing and Text Mining Technologies on Electronic Medical Records: A Review

PubMed Central

Sun, Wencheng; Li, Yangyang; Liu, Fang; Fang, Shengqun; Wang, Guoyan

2018-01-01

Currently, medical institutes generally use EMR to record patient's condition, including diagnostic information, procedures performed, and treatment results. EMR has been recognized as a valuable resource for large-scale analysis. However, EMR has the characteristics of diversity, incompleteness, redundancy, and privacy, which make it difficult to carry out data mining and analysis directly. Therefore, it is necessary to preprocess the source data in order to improve data quality and improve the data mining results. Different types of data require different processing technologies. Most structured data commonly needs classic preprocessing technologies, including data cleansing, data integration, data transformation, and data reduction. For semistructured or unstructured data, such as medical text, containing more health information, it requires more complex and challenging processing methods. The task of information extraction for medical texts mainly includes NER (named-entity recognition) and RE (relation extraction). This paper focuses on the process of EMR processing and emphatically analyzes the key techniques. In addition, we make an in-depth study on the applications developed based on text mining together with the open challenges and research issues for future work. PMID:29849998

Registered nurses' clinical reasoning in home healthcare clinical practice: A think-aloud study with protocol analysis.

PubMed

Johnsen, Hege Mari; Slettebø, Åshild; Fossum, Mariann

2016-05-01

The home healthcare context can be unpredictable and complex, and requires registered nurses with a high level of clinical reasoning skills and professional autonomy. Thus, additional knowledge about registered nurses' clinical reasoning performance during patient home care is required. The aim of this study is to describe the cognitive processes and thinking strategies used by recently graduated registered nurses while caring for patients in home healthcare clinical practice. An exploratory qualitative think-aloud design with protocol analysis was used. Home healthcare visits to patients with stroke, diabetes, and chronic obstructive pulmonary disease in seven healthcare districts in southern Norway. A purposeful sample of eight registered nurses with one year of experience. Each nurse was interviewed using the concurrent think-aloud technique in three different patient home healthcare clinical practice visits. A total of 24 home healthcare visits occurred. Follow-up interviews were conducted with each participant. The think-aloud sessions were transcribed and analysed using three-step protocol analysis. Recently graduated registered nurses focused on both general nursing concepts and concepts specific to the domains required and tasks provided in home healthcare services as well as for different patient groups. Additionally, participants used several assertion types, cognitive processes, and thinking strategies. Our results showed that recently graduated registered nurses used both simple and complex cognitive processes involving both inductive and deductive reasoning. However, their reasoning was more reactive than proactive. The results may contribute to nursing practice in terms of developing effective nursing education programmes. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effect of basicity on beneficiated chromite sand smelting process using submerged arc furnace

NASA Astrophysics Data System (ADS)

Nurjaman, F.; Subandrio, S.; Ferdian, D.; Suharno, Bambang

2018-05-01

Ferrochrome is an important alloy in stainless steel making due to its contribution to high strength and corrosion resistance. In this present study, ferrochrome was derived from Indonesian chromite sand with low-grade Cr/Fe ratio. In order to improve the ratio, beneficiation process such as pre-magnetic separation and reduction process at 1000°C for 60 minutes was required. The process followed by another magnetic separation, thus the Cr/Fe ratio was increased from 0.9 to 1.6. The reduction process used coconut shell charcoal as reductant and limestone as an additive. The beneficiated sand chromite was briquette using bentonite as a binder in 2 wt.% before it was smelted in a submerged electric arc furnace to produce ferrochrome. Basicity was controlled by the addition of limestone and it was varied from 0.4-1.6. Furthermore, the composition of ferrochrome was analyzed by using X-Ray Fluorescence. From this experiment, the result showed that chromium recovery and specific energy was decreased with the increasing of slag basicity.

Modified batch anaerobic digestion assay for testing efficiencies of trace metal additives to enhance methane production of energy crops.

PubMed

Brulé, Mathieu; Bolduan, Rainer; Seidelt, Stephan; Schlagermann, Pascal; Bott, Armin

2013-01-01

Batch biochemical methane potential (BMP) assays to evaluate the methane yield of biogas substrates such as energy crops are usually carried out with undiluted inoculum. A BMP assay was performed on two energy crops (green cuttings and grass silage). Anaerobic digestion was performed both with and without supplementation of three commercial additives containing trace metals in liquid, solid or adsorbed form (on clay particles). In order to reveal positive effects of trace metal supplementation on the methane yield, besides undiluted inoculum, 3-fold and 10-fold dilutions of the inoculum were applied for substrate digestion. Diluted inoculum variants were supplemented with both mineral nutrients and pH-buffering substances to prevent a collapse of the digestion process. As expected, commercial additives had no effect on the digestion process performed with undiluted inoculum, while significant increases of methane production through trace element supplementation could be observed on the diluted variants. The effect of inoculum dilution may be twofold: (1) decrease in trace metal supplementation from the inoculum and (2) reduction in the initial number of bacterial cells. Bacteria require higher growth rates for substrate degradation and hence have higher trace element consumption. According to common knowledge of the biogas process, periods with volatile fatty acids accumulation and decreased pH may have occurred in the course ofanaerobic digestion. These effects may have led to inhibition, not only ofmethanogenes and acetogenes involved in the final phases of methane production, but also offibre-degrading bacterial strains involved in polymer hydrolysis. Further research is required to confirm this hypothesis.

Enhanced cellulase recovery without β-glucosidase supplementation for cellulosic ethanol production using an engineered strain and surfactant.

PubMed

Huang, Renliang; Guo, Hong; Su, Rongxin; Qi, Wei; He, Zhimin

2017-03-01

Recycling cellulases by substrate adsorption is a promising strategy for reducing the enzyme cost of cellulosic ethanol production. However, β-glucosidase has no carbohydrate-binding module (CBM). Thus, additional enzymes are required in each cycle to achieve a high ethanol yield. In this study, we report a new method of recycling cellulases without β-glucosidase supplementation using lignocellulosic substrate, an engineered strain expressing β-glucosidase and Tween 80. The cellulases and Tween 80 were added to an aqueous suspension of diluted sulfuric acid/ammonia-treated corncobs in a simultaneous saccharification and fermentation (SSF) process for ethanol production. Subsequently, the addition of fresh pretreated corncobs to the fermentation liquor and remaining solid residue provided substrates with absorbed cellulases for the next SSF cycle. This method provided excellent ethanol production in three successive SSF cycles without requiring the addition of new cellulases. For a 10% (w/v) solid loading, a cellulase dosage of 30 filter paper units (FPU)/g cellulose, 0.5% Tween 80, and 2 g/L of the engineered strain, approximately 90% of the initial ethanol concentration from the first SSF process was obtained in the next two SSF processes, with a total ethanol production of 306.27 g/kg corncobs and an enzyme productivity of 0.044 g/FPU. Tween 80 played an important role in enhancing cellulase recovery. This new enzyme recycling method is more efficient and practical than other reported methods. Biotechnol. Bioeng. 2017;114: 543-551. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Achieving continuous manufacturing: technologies and approaches for synthesis, workup, and isolation of drug substance. May 20-21, 2014 Continuous Manufacturing Symposium.

PubMed

Baxendale, Ian R; Braatz, Richard D; Hodnett, Benjamin K; Jensen, Klavs F; Johnson, Martin D; Sharratt, Paul; Sherlock, Jon-Paul; Florence, Alastair J

2015-03-01

This whitepaper highlights current challenges and opportunities associated with continuous synthesis, workup, and crystallization of active pharmaceutical ingredients (drug substances). We describe the technologies and requirements at each stage and emphasize the different considerations for developing continuous processes compared with batch. In addition to the specific sequence of operations required to deliver the necessary chemical and physical transformations for continuous drug substance manufacture, consideration is also given to how adoption of continuous technologies may impact different manufacturing stages in development from discovery, process development, through scale-up and into full scale production. The impact of continuous manufacture on drug substance quality and the associated challenges for control and for process safety are also emphasized. In addition to the technology and operational considerations necessary for the adoption of continuous manufacturing (CM), this whitepaper also addresses the cultural, as well as skills and training, challenges that will need to be met by support from organizations in order to accommodate the new work flows. Specific action items for industry leaders are: Develop flow chemistry toolboxes, exploiting the advantages of flow processing and including highly selective chemistries that allow use of simple and effective continuous workup technologies. Availability of modular or plug and play type equipment especially for workup to assist in straightforward deployment in the laboratory. As with learning from other industries, standardization is highly desirable and will require cooperation across industry and academia to develop and implement. Implement and exploit process analytical technologies (PAT) for real-time dynamic control of continuous processes. Develop modeling and simulation techniques to support continuous process development and control. Progress is required in multiphase systems such as crystallization. Involve all parts of the organization from discovery, research and development, and manufacturing in the implementation of CM. Engage with academia to develop the training provision to support the skills base for CM, particularly in flow chemistry, physical chemistry, and chemical engineering skills at the chemistry-process interface. Promote and encourage publication and dissemination of examples of CM across the sector to demonstrate capability, engage with regulatory comment, and establish benchmarks for performance and highlight challenges. Develop the economic case for CM of drug substance. This will involve various stakeholders at project and business level, however establishing the critical economic drivers is critical to driving the transformation in manufacturing. © 2014 Wiley Periodicals, Inc. and the American Pharmacists Association.

Data quality objectives for TWRS privatization phase 1: confirm tank T is an appropriate feed source for low-activity waste feed batch X

DOE Office of Scientific and Technical Information (OSTI.GOV)

NGUYEN, D.M.

1999-06-01

The US. Department of Energy, Richland Operations Office (DOE-RL) has initiated Phase 1 of a two-phase privatization strategy for treatment and immobilization of low-activity waste (LAW) currently being managed by the Hanford Tank Waste Remediation System (TWRS) Project. In this strategy, DOE will purchase services from a contractor-owned and operated facility under a fixed price. The Phase 1 TWRS privatization contract requires that the Project Hanford Management Contract (PHMC) contractors, on behalf of DOE, deliver LAW feed in specified quantities and composition to the Privatization Contractor in a timely manner (DOE-RL 1996). Additional requirements are imposed by the interface controlmore » document (ICD-19) for LAW feed (PHMC 1997). In response to these requirements, the Tank Waste Remediation System Operation and Utilization Plan (TWRSO and UP) (Kirkbride et al. 1997) was prepared by the PHMC. The TWRSO and UP, as updated by the Readiness-To-Proceed deliverable (Payne et al. 1998), establishes the baseline operating scenario for the delivery of LAW feed to the Privatization Contractor. The scenario specifies tanks from which LAW will be provided for each feed batch, the operational activities needed to prepare and deliver each batch, and the timing of these activities. The operating scenario was developed based on current knowledge of waste composition and chemistry, waste transfer methods, and operating constraints, such as tank farm logistics and availability of tank space. A project master baseline schedule (PMBS) has been developed to implement the operating scenario. The PMBS also includes activities aimed at reducing programmatic risks. One of the activities, ''Confirm Plans and Requirements,'' was identified to verify the basis used to develop the scenario. Additional data on waste quantity, physical and chemical characteristics, and transfer properties will be needed to support this activity. This document describes the data quality objective (DQO) process undertaken to assme appropriate data will be collected to support the activity, ''Confirm Tank Plans and Requirements.'' The DQO process was implemented in accordance with the TWRS DQO process (Banning 1997) with some modifications to accommodate project or tank-specific requirements and constraints.« less

Convolutional code performance in planetary entry channels

NASA Technical Reports Server (NTRS)

Modestino, J. W.

1974-01-01

The planetary entry channel is modeled for communication purposes representing turbulent atmospheric scattering effects. The performance of short and long constraint length convolutional codes is investigated in conjunction with coherent BPSK modulation and Viterbi maximum likelihood decoding. Algorithms for sequential decoding are studied in terms of computation and/or storage requirements as a function of the fading channel parameters. The performance of the coded coherent BPSK system is compared with the coded incoherent MFSK system. Results indicate that: some degree of interleaving is required to combat time correlated fading of channel; only modest amounts of interleaving are required to approach performance of memoryless channel; additional propagational results are required on the phase perturbation process; and the incoherent MFSK system is superior when phase tracking errors are considered.

Orbital transfer vehicle launch operations study. Volume 2: Detailed summary

NASA Technical Reports Server (NTRS)

1986-01-01

A series of Operational Design Drivers were identified. Several of these could have significant impact(s) on program costs. These recommendations, for example, include such items as: complete factory assembly and checkout prior to shipment to the ground launch site to make significant reductions in time required at the launch site as well as overall manpower required to do this work; minimize use of nonstandard equipment when orbiter provided equipment is available; and require commonality (or interchangeability) of subsystem equipment elements that are common to the space station, Orbit Maneuvering Vehicles, and/or Orbit Transfer Vehicles. Several additional items were identified that will require a significant amount of management attention (and direction) to resolve. Key elements of the space based processing plans are discussed.

Mission simulation as an approach to develop requirements for automation in Advanced Life Support Systems

NASA Technical Reports Server (NTRS)

Erickson, J. D.; Eckelkamp, R. E.; Barta, D. J.; Dragg, J.; Henninger, D. L. (Principal Investigator)

1996-01-01

This paper examines mission simulation as an approach to develop requirements for automation and robotics for Advanced Life Support Systems (ALSS). The focus is on requirements and applications for command and control, control and monitoring, situation assessment and response, diagnosis and recovery, adaptive planning and scheduling, and other automation applications in addition to mechanized equipment and robotics applications to reduce the excessive human labor requirements to operate and maintain an ALSS. Based on principles of systems engineering, an approach is proposed to assess requirements for automation and robotics using mission simulation tools. First, the story of a simulated mission is defined in terms of processes with attendant types of resources needed, including options for use of automation and robotic systems. Next, systems dynamics models are used in simulation to reveal the implications for selected resource allocation schemes in terms of resources required to complete operational tasks. The simulations not only help establish ALSS design criteria, but also may offer guidance to ALSS research efforts by identifying gaps in knowledge about procedures and/or biophysical processes. Simulations of a planned one-year mission with 4 crewmembers in a Human Rated Test Facility are presented as an approach to evaluation of mission feasibility and definition of automation and robotics requirements.

DWPF Recycle Evaporator Simulant Tests

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stone, M

2005-04-05

Testing was performed to determine the feasibility and processing characteristics of an evaporation process to reduce the volume of the recycle stream from the Defense Waste Processing Facility (DWPF). The concentrated recycle would be returned to DWPF while the overhead condensate would be transferred to the Effluent Treatment Plant. Various blends of evaporator feed were tested using simulants developed from characterization of actual recycle streams from DWPF and input from DWPF-Engineering. The simulated feed was evaporated in laboratory scale apparatus to target a 30X volume reduction. Condensate and concentrate samples from each run were analyzed and the process characteristics (foaming,more » scaling, etc) were visually monitored during each run. The following conclusions were made from the testing: Concentration of the ''typical'' recycle stream in DWPF by 30X was feasible. The addition of DWTT recycle streams to the typical recycle stream raises the solids content of the evaporator feed considerably and lowers the amount of concentration that can be achieved. Foaming was noted during all evaporation tests and must be addressed prior to operation of the full-scale evaporator. Tests were conducted that identified Dow Corning 2210 as an antifoam candidate that warrants further evaluation. The condensate has the potential to exceed the ETP WAC for mercury, silicon, and TOC. Controlling the amount of equipment decontamination recycle in the evaporator blend would help meet the TOC limits. The evaporator condensate will be saturated with mercury and elemental mercury will collect in the evaporator condensate collection vessel. No scaling on heating surfaces was noted during the tests, but splatter onto the walls of the evaporation vessels led to a buildup of solids. These solids were difficult to remove with 2M nitric acid. Precipitation of solids was not noted during the testing. Some of the aluminum present in the recycle streams was converted from gibbsite to aluminum oxide during the evaporation process. The following recommendations were made: Recycle from the DWTT should be metered in slowly to the ''typical'' recycle streams to avoid spikes in solids content to allow consistent processing and avoid process upsets. Additional studies should be conducted to determine acceptable volume ratios for the HEME dissolution and decontamination solutions in the evaporator feed. Dow Corning 2210 antifoam should be evaluated for use to control foaming. Additional tests are required to determine the concentration of antifoam required to prevent foaming during startup, the frequency of antifoam additions required to control foaming during steady state processing, and the ability of the antifoam to control foam over a range of potential feed compositions. This evaluation should also include evaluation of the degradation of the antifoam and impact on the silicon and TOC content of the condensate. The caustic HEME dissolution recycle stream should be neutralized to at least pH of 7 prior to blending with the acidic recycle streams. Dow Corning 2210 should be used during the evaporation testing using the radioactive recycle samples received from DWPF. Evaluation of additional antifoam candidates should be conducted as a backup for Dow Corning 2210. A camera and/or foam detection instrument should be included in the evaporator design to allow monitoring of the foaming behavior during operation. The potential for foam formation and high solids content should be considered during the design of the evaporator vessel.« less

Additive Manufacturing of Advanced High Temperature Masking Fixtures for EBPVD TBC Coating

DOE Office of Scientific and Technical Information (OSTI.GOV)

List, III, Frederick Alyious; Feuerstein, Albert; Dehoff, Ryan

2016-03-30

The purpose of this Manufacturing Demonstration Facility (MDF) technical collaboration project between Praxair Surface Technologies, Inc. (PST) and Oak Ridge National Laboratory (ORNL) was to develop an additive manufacturing process to fabricate next generation high temperature masking fixtures for coating of turbine airfoils with ceramic Thermal Barrier Coatings (TBC) by the Electron Beam Physical Vapor Deposition (EBPVD) process. Typical masking fixtures are sophisticated designs and require complex part manipulation in order to achieve the desired coating distribution. Fixtures are typically fabricated from high temperature nickel (Ni) based superalloys. The fixtures are fabricated from conventional processes by welding of thin sheetmore » material into a complex geometry, to decrease the weight load for the manipulator and to reduce the thermal mass of the fixture. Recent attempts have been made in order to fabricate the fixtures through casting, but thin walled sections are difficult to cast and have high scrap rates. This project focused on understanding the potential for fabricating high temperature Ni based superalloy fixtures through additive manufacturing. Two different deposition processes; electron beam melting (EBM) and laser powder bed fusion were evaluated to determine the ideal processing route of these materials. Two different high temperature materials were evaluated. The high temperature materials evaluated were Inconel 718 and another Ni base alloy, designated throughout the remainder of this document as Alloy X, as the alloy composition is sensitive. Inconel 718 is a more widely utilized material for additive manufacturing although it is not currently the material utilized for current fixtures. Alloy X is the alloy currently used for the fixtures, but is not a commercially available alloy for additive manufacturing. Praxair determined it was possible to build the fixture using laser powder bed technology from Inconel 718. ORNL fabricated the fixture geometry using the EBM technology in order to compare deposition features such as surface roughness, geometric accuracy, deposition rate, surface and subsurface porosity, and material quality. It was determined that the laser powder bed technology was ideal for the geometry and requirements of the fixture set by Praxair, and Praxair moved forward with the purchase of a laser powder bed system. The subsequent portion of the project focused on determining the ideal processing parameters for alloy X for the laser powder bed system using ORNL’s Renishaw laser powder bed system. Praxair supplied gas atomized powders of alloy X material with properties specified by ORNL. ORNL printed text cube arrays in order to determine the ideal combination of laser powder and laser travel speed in order to maximize material density, improve surface quality, and maintain geometric accuracy. Additional powder supplied by Praxair was used to fabricate a full-scale fixture component.« less

Antifibrinolytic agents and desmopressin as hemostatic agents in cardiac surgery.

PubMed

Erstad, B L

2001-09-01

To review the use of systemic hemostatic medications for reducing bleeding and transfusion requirements with cardiac surgery. Articles were obtained through computerized searches involving MEDLINE (from 1966 to September 2000). Additionally, several textbooks containing information on the diagnosis and management of bleeding associated with cardiac surgery were reviewed. The bibliographies of retrieved publications and textbooks were reviewed for additional references. Due to the large number of randomized investigations involving systemic hemostatic medications for reducing bleeding associated with cardiac surgery, the article selection process focused on recent randomized controlled trials, metaanalyses and pharmacoeconomic evaluations. The primary outcomes extracted from the literature were blood loss and associated transfusion requirements, although other outcome measures such as mortality were extracted when available. Although the majority of investigations for reducing cardiac bleeding and transfusion requirements have involved aprotinin, evidence from recent meta-analyses and randomized trials indicates that the synthetic antifibrinolytic agents, aminocaproic acid and tranexamic acid, have similar clinical efficacy. Additionally, aminocaproic acid (and to a lesser extent tranexamic acid) is much less costly. More comparative information of hemostatic agents is needed retative to other outcomes (eg., reoperation rates, myocardial infarction, stroke). There is insufficient evidence to recommend the use of desmopressin for reducing bleeding and transfusion requirements in cardiac surgery, although certain subsets of patients may benefit from its use. Of the medications that have been used to reduce bleeding and transfusion requirements with cardiac surgery, the antifibrinolytic agents have the best evidence supporting their use. Aminocaproic acid is the least costly therapy based on medication costs and transfusion requirements.

Radiometric spectral and band rendering of targets using anisotropic BRDFs and measured backgrounds

NASA Astrophysics Data System (ADS)

Hilgers, John W.; Hoffman, Jeffrey A.; Reynolds, William R.; Jafolla, James C.

2000-07-01

Achievement of ultra-high fidelity signature modeling of targets requires a significant level of complexity for all of the components required in the rendering process. Specifically, the reflectance of the surface must be described using the bi-directional distribution function (BRDF). In addition, the spatial representation of the background must be high fidelity. A methodology and corresponding model for spectral and band rendering of targets using both isotropic and anisotropic BRDFs is presented. In addition, a set of tools will be described for generating theoretical anisotropic BRDFs and for reducing data required for a description of an anisotropic BRDF by 5 orders of magnitude. This methodology is hybrid using a spectrally measured panoramic of the background mapped to a large hemisphere. Both radiosity and ray-tracing approaches are incorporated simultaneously for a robust solution. In the thermal domain the spectral emission is also included in the solution. Rendering examples using several BRDFs will be presented.

The future of PanDA in ATLAS distributed computing

NASA Astrophysics Data System (ADS)

De, K.; Klimentov, A.; Maeno, T.; Nilsson, P.; Oleynik, D.; Panitkin, S.; Petrosyan, A.; Schovancova, J.; Vaniachine, A.; Wenaus, T.

2015-12-01

Experiments at the Large Hadron Collider (LHC) face unprecedented computing challenges. Heterogeneous resources are distributed worldwide at hundreds of sites, thousands of physicists analyse the data remotely, the volume of processed data is beyond the exabyte scale, while data processing requires more than a few billion hours of computing usage per year. The PanDA (Production and Distributed Analysis) system was developed to meet the scale and complexity of LHC distributed computing for the ATLAS experiment. In the process, the old batch job paradigm of locally managed computing in HEP was discarded in favour of a far more automated, flexible and scalable model. The success of PanDA in ATLAS is leading to widespread adoption and testing by other experiments. PanDA is the first exascale workload management system in HEP, already operating at more than a million computing jobs per day, and processing over an exabyte of data in 2013. There are many new challenges that PanDA will face in the near future, in addition to new challenges of scale, heterogeneity and increasing user base. PanDA will need to handle rapidly changing computing infrastructure, will require factorization of code for easier deployment, will need to incorporate additional information sources including network metrics in decision making, be able to control network circuits, handle dynamically sized workload processing, provide improved visualization, and face many other challenges. In this talk we will focus on the new features, planned or recently implemented, that are relevant to the next decade of distributed computing workload management using PanDA.