Response of Leaf Water Potential, Stomatal Resistance, and Leaf Rolling to Water Stress

PubMed Central

O'Toole, John C.; Cruz, Rolando T.

1980-01-01

Numerous studies have associated increased stomatal resistance with response to water deficit in cereals. However, consideration of change in leaf form seems to have been neglected. The response of adaxial and abaxial stomatal resistance and leaf rolling in rice to decreasing leaf water potential was investigated. Two rice cultivars were subjected to control and water stress treatments in a deep (1-meter) aerobic soil. Concurrent measurements of leaf water potential, stomatal resistance, and degree of leaf rolling were made through a 29-day period after cessation of irrigation. Kinandang Patong, an upland adapted cultivar, maintained higher dawn and midday leaf water potential than IR28, a hybrid selected in irrigated conditions. This was not explained by differences in leaf diffusive resistance or leaf rolling, and is assumed to result from a difference in root system extent. Stomatal resistance increased more on the abaxial than the adaxial leaf surface in both cultivars. This was associated with a change in leaf form or rolling inward of the upper leaf surface. Both responses, increased stomatal resistance and leaf rolling, were initiated in a similar leaf water potential range (−8 to −12 bars). Leaves of IR28 became fully rolled at leaf water potential of about −22 bars; however, total leaf diffusive resistance was only about 4 to 5 seconds per centimeter (conductance 0.25 to 0.2 centimeter per second) at that stage. Leaf diffusive resistance and degree of leaf rolling were linearly related to leaf water potential. Thus, leaf rolling in rice may be used as an estimate of the other two less obvious effects of water deficit. PMID:16661206

Multiphysical FE-analysis of a front-end bending phenomenon in a hot strip mill

NASA Astrophysics Data System (ADS)

Ilmola, Joonas; Seppälä, Oskari; Leinonen, Olli; Pohjonen, Aarne; Larkiola, Jari; Jokisaari, Juha; Putaansuu, Eero

2018-05-01

In hot steel rolling processes, a slab is generally rolled to a transfer bar in a roughing process and to a strip in a hot strip rolling process. Over several rolling passes the front-end may bend upward or downward due to asymmetrical rolling conditions causing entry problems in the next rolling pass. Many different factors may affect the front-end bending phenomenon and are very challenging to measure. Thus, a customized finite element model is designed and built to simulate the front-end bending phenomenon in a hot strip rolling process. To simulate the functioning of the hot strip mill precisely, automated controlling logic of the mill must be considered. In this paper we studied the effect of roll bite friction conditions and amount of reduction on the front-end bending phenomenon in a hot strip rolling process.

Preliminary Assessment of Primary Flight Display Symbology for Electro- Optic Head-Down Displays

DTIC Science & Technology

1991-06-01

information :elated to pitch and power; the vertica! line provides information related to bank and heading. As a result of this geometrica ...steering bar are centered over the aircraft symbol. -n -1-- If the bars are centered, the aircraft is either correcting properly or is flying the desired...a•Isd bas,:ý muve to provide a new pitch command. Roll theading correction ) commands are seen as unbalanced line width, the low command bar side

MULTIPLE SETS OF TWIN SLABS ON THE RUN OUT. THE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

MULTIPLE SETS OF TWIN SLABS ON THE RUN OUT. THE RUN OUT INCLUDES THE TRAVELING TORCH WHICH CUTS SLABS TO DESIRED LENGTH, AN IDENTIFICATION SYSTEM TO INDICATE HEAT NUMBER AND TRACE IDENTITY OF EVERY SLAB, AND A DEBURRING DEVICE TO SMOOTH SLABS. AT LEFT OF ROLLS IS THE DUMMY BAR. DUMMY BAR IS INSERTED UP THROUGH CONTAINMENT SECTION INTO MOLD PRIOR TO START OF CAST. WHEN STEEL IS INTRODUCED INTO MOLD IT CONNECTS WITH BAR AS CAST BEGINS, AT RUN OUT DUMMY BAR DISCONNECTS AND IS STORED. - U.S. Steel, Fairfield Works, Continuous Caster, Fairfield, Jefferson County, AL

MULTIPLE SETS OF TWIN SLABS ON THE RUN OUT. THE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

MULTIPLE SETS OF TWIN SLABS ON THE RUN OUT. THE RUN OUT INCLUDES THE TRAVELING TORCH WHICH CUTS SLABS TO DESIRED LENGTH, AN IDENTIFICATION SYSTEM TO INDICATE HEAT NUMBER AND TRACE IDENTITY OF EVERY SLAB, AND A DEBURRING DEVICE TO SMOOTH SLABS. AT LEFT OF ROLLS IS THE DUMMY BAR. DUMMY BAR IS INSERTED UP THROUGH CONTAINMENT SECTION INTO MOLD PRIOR TO START OF CAST. WHEN STEEL IS INTRODUCED INTO MOLD IT CONNECTS WITH BAR AS CAST BEGINS, AT RUN OUT DUMMY BAR DISCONNECTS AND IS STORED - U.S. Steel, Fairfield Works, Continuous Caster, Fairfield, Jefferson County, AL

17. VIEW OF THE FINAL STEP AT THE NO. 31 ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

17. VIEW OF THE FINAL STEP AT THE NO. 31 MILL; THE BRASS BARS ARE WOUND ONTO SPOOLS; THE AVERAGE OUTPUT PER HOUSE SHIFT WAS 200 TO 250 BARS. MOST OF THIS MATERIAL IS USED IN THE ELECTRICAL MANUFACTURING INDUSTRY FOR FUSES, BUS FARES, ELECTRICAL RELAYS, AND OTHER SUCH PRODUCTS. - American Brass Company, Kenosha Works, Hot Roll Mill, Kenosha, Kenosha County, WI

Food Preparation Studies

DTIC Science & Technology

1974-11-01

delivery to the satellites. Specialty baked goods such as cakes, brownies, bars, cookies , pies, tortes, and coffee cakes will be made at the CFPF...products (cakes, rolls, brownies, pie crusts, and tortes) will be made with mixes, but cookies , bars, and coffee cakes generally will be made from...scratch. Production of baked goods requires the following specialized equipment: • Planetary mixers • Dough mixers • Sheeters • Pie machines

Variable Dynamic Testbed Vehicle Dynamics Analysis

DOT National Transportation Integrated Search

1996-03-01

ANTI-ROLL BAR, EMULATION, FOUR-WHEEL-STEERING, LATERAL RESPONSE CHARACTERISTICS, SIMULATION, VARIABLE DYNAMIC TESTBED VEHICLE, INTELLIGENT VEHICLE INITIATIVE OR IVI : THE VARIABLE DYNAMIC TESTBED VEHICLE (VDTV) CONCEPT HAS BEEN PROPOSED AS A TOOL...

Surface Fatigue Tests Of M50NiL Gears And Bars

NASA Technical Reports Server (NTRS)

Townsend, Dennis P.; Bamberger, Eric N.

1994-01-01

Report presents results of tests of steels for use in gears and bearings of advanced aircraft. Spur-gear endurance tests and rolling-element surface fatigue tests performed on gear and bar specimens of M50NiL steel processed by vacuum induction melting and vacuum arc remelting (VIM-VAR). Compares results of tests with similar tests of specimens of VIM-VAR AISI 9310 steel and of AISI 9310 steel subjected to VAR only.

Forging Oxide-Dispersion-Strengthened Superalloys

NASA Technical Reports Server (NTRS)

Harf, F. H.; Glasgow, T. K.; Moracz, D. J.; Austin, C. M.

1986-01-01

Cladding of mild steel prevents surface cracking when alloy contacts die. Continual need for improvements in properties of alloys capable of withstanding elevated temperatures. Accomplished by using oxide-dispersion-strengthed superalloys such as Inconel Alloy MA 6000. Elevated tensile properties of forged alloy equal those of hot-rolled MA 6000 bar. Stress-rupture properties somewhat lower than those of bar stock but, at 1,100 degrees C, exceed those of strongest commercial single crystal, directionally solidified and conventionally cast superalloys.

Analysis of Fatigue Crack Paths in Cold Drawn Pearlitic Steel

PubMed Central

Toribio, Jesús; González, Beatriz; Matos, Juan-Carlos

2015-01-01

In this paper, a fracto-metallographic analysis was performed on the cracked specimens of cold drawn pearlitic steel subjected to fatigue tests. Fatigue cracks are transcollonial and exhibit a preference for fracturing pearlitic lamellae, with non-uniform crack opening displacement values, micro-discontinuities, branchings, bifurcations and frequent local deflections that create microstructural roughness. At the micro-level, the cold drawn pearlitic steel exhibits higher micro-roughness than the hot rolled bar (this is a consequence of the manufacturing process by cold drawing), so that the actual fractured surface in the cold drawn wire is greater than that in the hot rolled bar, due to the fact that the crack deflection events are more frequent and with higher angle in the former (the heavily drawn prestressing steel wire). These findings show the relevant role on the manufacturing process by cold drawing in the fatigue crack propagation in pearlitic steel. PMID:28793647

Analysis of Fatigue Crack Paths in Cold Drawn Pearlitic Steel.

PubMed

Toribio, Jesús; González, Beatriz; Matos, Juan-Carlos

2015-11-04

In this paper, a fracto-metallographic analysis was performed on the cracked specimens of cold drawn pearlitic steel subjected to fatigue tests. Fatigue cracks are transcollonial and exhibit a preference for fracturing pearlitic lamellae, with non-uniform crack opening displacement values, micro-discontinuities, branchings, bifurcations and frequent local deflections that create microstructural roughness. At the micro-level, the cold drawn pearlitic steel exhibits higher micro-roughness than the hot rolled bar (this is a consequence of the manufacturing process by cold drawing), so that the actual fractured surface in the cold drawn wire is greater than that in the hot rolled bar, due to the fact that the crack deflection events are more frequent and with higher angle in the former (the heavily drawn prestressing steel wire). These findings show the relevant role on the manufacturing process by cold drawing in the fatigue crack propagation in pearlitic steel.

Structural Engineering. Loads. Design Manual 2.2.

DTIC Science & Technology

1981-11-01

cast, rolled 534 Locust 46 Bronze, 7.9 to 14% Sn 509 Maple, hard 43 Bronze, aluminum 481 Maple, white 33 Copper , cast, rolled 556 Oak, chestnut 54... Copper ore, pyrites 262 Oak, live 59 Gold, cast, hammered 1205 Oak, red, black 41 Gold, bars, stacked 1133 Oak, white 46 Gold, coin in bags 1084 Pine...Phosphate rock, apatite 200 Glass, crystal 184 Porphyry 172 Hay and straw - bales 20 Pumice, natural 40 Leather 59 Quartz, flint 165 Paper 58 Sandstone

Roll and pitch independently tuned interconnected suspension: modelling and dynamic analysis

NASA Astrophysics Data System (ADS)

Xu, Guangzhong; Zhang, Nong; Roser, Holger M.

2015-12-01

In this paper, a roll and pitch independently tuned hydraulically interconnected passive suspension is presented. Due to decoupling of vibration modes and the improved lateral and longitudinal stability, the stiffness of individual suspension spring can be reduced for improving ride comfort and road grip. A generalised 14 degree-of-freedom nonlinear vehicle model with anti-roll bars is established to investigate the vehicle ride and handling dynamic responses. The nonlinear fluidic model of the hydraulically interconnected suspension is developed and integrated with the full vehicle model to investigate the anti-roll and anti-pitch characteristics. Time domain analysis of the vehicle model with the proposed suspension is conducted under different road excitations and steering/braking manoeuvres. The dynamic responses are compared with conventional suspensions to demonstrate the potential of enhanced ride and handling performance. The results illustrate the model-decoupling property of the hydraulically interconnected system. The anti-roll and anti-pitch performance could be tuned independently by the interconnected systems. With the improved anti-roll and anti-pitch characteristics, the bounce stiffness and ride damping can be optimised for better ride comfort and tyre grip.

Surface fatigue life and failure characteristics of EX-53, CBS 1000M, and AISI 9310 gear materials

NASA Technical Reports Server (NTRS)

Townsend, D. P.

1985-01-01

Spur gear endurance tests and rolling-element surface fatigue tests are conducted to investigate EX-53 and CBS 1000M steels for use as advanced application gear materials, to determine their endurance characteristics, and to compare the results with the standard AISI 9310 gear material. The gear pitch diameter is 8.89 cm (3.50 in). Gear test conditions are an oil inlet temperature of 320 K (116 F), an oil outlet temperature of 350 K (170 F), a maximum Hertz stress of 1.71 GPa (248 ksi), and a speed of 10,000 rpm. Bench-type rolling-element fatigue tests are conducted at ambient temperature with a bar specimen speed of 12,500 rpm and a maximum Hertz stress of 4.83 GPa (700 ksi). The EX-53 test gears have a surface fatigue life of twice that of the AISI 9310 spur gears. The CBS 1000M test gears have a surface fatigue life of more than twice that of the AISI 9310 spur gears. However, the CBS 1000M gears experience a 30-percent tooth fracture failure which limits its use as a gear material. The rolling-contact fatigue lines of RC bar specimens of EX-53 and ASISI 9310 are approximately equal. However, the CBS 1000M RC specimens have a surface fatigue life of about 50 percent that of the AISI 9310.

Basic Principles of Thin-Walled Open Bars Taking into Account Where Influence Shifts of Cross Sections are Concerned

NASA Astrophysics Data System (ADS)

Panasenko, N. N.; Sinelschikov, A. V.

2017-11-01

The finite element method is considered to be the most effective in relation to the calculation of strength and stability of buildings and engineering constructions. As a rule, for the modelling of supporting 3-D frameworks, finite elements with six degrees of freedom are used in each of the nodes. In practice, such supporting frameworks represent the thin-walled welded bars and hot-rolled bars of open and closed profiles in which cross-sectional deplanation must be taken into account. This idea was first introduced by L N Vorobjev and brought to one of the easiest variants of the thin-walled bar theory. The development of this approach is based on taking into account the middle surface shear deformation and adding the deformations of a thin-walled open bar to the formulas for potential and kinetic energy; these deformations depend on shearing stress and result in decreasing the frequency of the first tone of fluctuations to 13%. The authors of the article recommend taking into account this fact when calculating fail-proof dynamic systems.

75 FR 67689 - Stainless Steel Bar From Brazil: Preliminary Results of Antidumping Duty Administrative Review

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-03

... from Brazil. The review covers one producer/ exporter of the subject merchandise, Villares Metals S.A... have indentations, ribs, grooves, or other deformations produced during the rolling process. Except as..., we used the following methodology. If an identical comparison-market model was reported, we made...

46 CFR 114.600 - Incorporation by reference.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Storage Tank Water Heaters 119.320 UL 486A-1992—Wire Connectors and Soldering Lugs For Use With Copper...-93, Standard Specification for Copper-Silicon Alloy Plate, Sheet, Strip, and Rolled Bar for General...) Apparatus 114.400 ASTM B 122/B 122M-95, Standard Specification for Copper-Nickel-Tin Alloy , Copper-Nickel...

Aircraft control position indicator

NASA Technical Reports Server (NTRS)

Dennis, Dale V. (Inventor)

1987-01-01

An aircraft control position indicator was provided that displayed the degree of deflection of the primary flight control surfaces and the manner in which the aircraft responded. The display included a vertical elevator dot/bar graph meter display for indication whether the aircraft will pitch up or down, a horizontal aileron dot/bar graph meter display for indicating whether the aircraft will roll to the left or to the right, and a horizontal dot/bar graph meter display for indicating whether the aircraft will turn left or right. The vertical and horizontal display or displays intersect to form an up/down, left/right type display. Internal electronic display driver means received signals from transducers measuring the control surface deflections and determined the position of the meter indicators on each dot/bar graph meter display. The device allows readability at a glance, easy visual perception in sunlight or shade, near-zero lag in displaying flight control position, and is not affected by gravitational or centrifugal forces.

Method and apparatus to control the lateral motion of a long metal bar being formed by a mechanical process such as rolling or drawing

DOEpatents

Chang, Tzyy-Shuh [Ann Arbor, MI; Huang, Hsun-Hau [Ann Arbor, MI; Lin, Chang-Hung [Ypsilanti, MI

2011-01-04

An apparatus to control lateral motion of a bar moving along a guidance path includes a pair of rotatable hubs each having at least first and second rollers at locations around the perimeter of the hub. The first roller has a first retaining groove of a first radius and the second roller has a second groove of a second radius smaller than the first radius. Each hub further includes at least one guiding element located between the rollers with a guide channel extending in the outer surface. A mounting system allows the hubs to be rotated between first and second positions. In the first position the first rollers oppose each other forming a guideway having a first, enlarged diameter for capturing a free end of an approaching bar. In the second position the second rollers form a second, smaller diameter to match the actual size of the bar.

Grain size effects on stability of nonlinear vibration with nanocrystalline NiTi shape memory alloy

NASA Astrophysics Data System (ADS)

Xia, Minglu; Sun, Qingping

2017-10-01

Grain size effects on stability of thermomechanical responses for a nonlinear torsional vibration system with nanocrystalline superelastic NiTi bar are investigated in the frequency and amplitude domains. NiTi bars with average grain size from 10 nm to 100 nm are fabricated through cold-rolling and subsequent annealing. Thermomechanical responses of the NiTi bar as a softening nonlinear damping spring in the torsional vibration system are obtained by synchronised acquisition of rotational angle and temperature under external sinusoidal excitation. It is shown that nonlinearity and damping capacity of the NiTi bar decrease as average grain size of the material is reduced below 100 nm. Therefore jump phenomena of thermomechanical responses become less significant or even vanish and the vibration system becomes more stable. The work in this paper provides a solid experimental base for manipulating the undesired jump phenomena of thermomechanical responses and stabilising the mechanical vibration system through grain refinement of NiTi SMA.

Manufacturing Methods for Strategic Materials Reclamation.

DTIC Science & Technology

1979-12-14

86 AIRCO Ingot N o. 4116 Casting Profile ......................................................... 199 87 Identification of Conversion of AIRCO Ingot...No. 4115 to Bar Stock .............. 201 88 6-in. RCS Billet Cutting Layout for Samples of Ingot No. 4115 Sent to P&WA 202 89 Identification of 1-in...132 31 Identification of Foreign Particles Detected in Rolled Plate .......................... 136 32 Mechanical Property Data of

Comparison of Ductile-to-Brittle Transition Behavior in Two Similar Ferritic Oxide Dispersion Strengthened Alloys.

PubMed

Chao, Jesus; Rementeria, Rosalia; Aranda, Maria; Capdevila, Carlos; Gonzalez-Carrasco, Jose Luis

2016-07-29

The ductile-to-brittle transition (DBT) behavior of two similar Fe-Cr-Al oxide dispersion strengthened (ODS) stainless steels was analyzed following the Cottrell-Petch model. Both alloys were manufactured by mechanical alloying (MA) but by different forming routes. One was manufactured as hot rolled tube, and the other in the form of hot extruded bar. The two hot forming routes considered do not significantly influence the microstructure, but cause differences in the texture and the distribution of oxide particles. These have little influence on tensile properties; however, the DBT temperature and the upper shelf energy (USE) are significantly affected because of delamination orientation with regard to the notch plane. Whereas in hot rolled material the delaminations are parallel to the rolling surface, in the hot extruded material, they are randomly oriented because the material is transversally isotropic.

Comparison of Ductile-to-Brittle Transition Behavior in Two Similar Ferritic Oxide Dispersion Strengthened Alloys

PubMed Central

Chao, Jesus; Rementeria, Rosalia; Aranda, Maria; Capdevila, Carlos; Gonzalez-Carrasco, Jose Luis

2016-01-01

The ductile-to-brittle transition (DBT) behavior of two similar Fe-Cr-Al oxide dispersion strengthened (ODS) stainless steels was analyzed following the Cottrell–Petch model. Both alloys were manufactured by mechanical alloying (MA) but by different forming routes. One was manufactured as hot rolled tube, and the other in the form of hot extruded bar. The two hot forming routes considered do not significantly influence the microstructure, but cause differences in the texture and the distribution of oxide particles. These have little influence on tensile properties; however, the DBT temperature and the upper shelf energy (USE) are significantly affected because of delamination orientation with regard to the notch plane. Whereas in hot rolled material the delaminations are parallel to the rolling surface, in the hot extruded material, they are randomly oriented because the material is transversally isotropic. PMID:28773764

Effect of temperature on the anisotropy of AZ31 magnesium alloy rolling sheet under high strain rate deformation

NASA Astrophysics Data System (ADS)

Liu, Yanyu; Mao, Pingli; Zhang, Feng; Liu, Zheng; Wang, Zhi

2018-04-01

In order to investigate the effect of temperature on the anisotropic behaviour of AZ31 magnesium alloy rolling sheet under high strain rate deformation, the Split Hopkinson Pressure Bar was used to analyse the dynamic mechanical properties of AZ31 magnesium alloy rolling sheet in three directions, rolling direction(RD), transverse direction (TD) and normal direction (ND). The texture of the rolling sheet was characterised by X-ray analysis and the microstructure prior and after high strain rate deformation was observed by optical microscope (OM). The results demonstrated that AZ31magnesium alloy rolling sheet has strong initial {0 0 0 2} texture, which resulted at the obvious anisotropy in high strain rate deformation at 20 °C. The anisotropy reflected in stress-strain curve, yield stress, peak stress and microstructure. The anisotropy became much weaker when the deformation temperature increased up to 250 °C. Continuing to increase the deformation temperature to 350 °C the anisotropy of AZ31 rolling sheet essentially disappeared. The decreasing tendency of anisotropy with increasing temperature was due to the fact that when the deformation temperature increased, the critical resolved shear stress (CRSS) for pyramidal 〈c + a〉 slip, which was the predominant slip mechanism for ND, decreased close to that of twinning, which was the predominant deformation mechanism for RD and TD. The deformation mechanism at different directions and temperatures and the Schmid factor (SF) at different directions were discussed in the present paper.

Status of Standardization Projects

DTIC Science & Technology

1992-09-30

0872 ANSIZ83 14 GAS FD SV EQ COUNTER APPLI GL G5 B 912 921 922 A GL YD 99 GS U B 7320 0874 A A XXX CABINET DOUGH PRF 18 PAN CAP GL 84 A 914 931 931 A GL...N D 7320 0897 MIL-D-2467F DOUGH ROLLING MACHINES PIE YD H5 924 934 934 A YD 99 N 7320 0898 0O-D-2813 DOUGH ROLLING MACHINES PIE YD 84 924 934 934 A...934 934 A GL SA 50 SS N 8920 0551 MIL-F-44279GL FRUIT BARS OPER RAT COMP GL F2 924 934 934 A GL SA 50 SS N 8920 0552 MIL-O-44136B OATMEAL COOKIE AND

Status of Standardization Projects

DTIC Science & Technology

1992-12-31

GL G5 922 931 931 A GL YD 99 GS N C 7320 0897 MIL-D-2467F DOUGH ROLLING MACHINES PIE YD H5 924 934 934 A YD 99 N 7320 0898 00-D-2813 DOUGH ROLLING...924 934 934 A GL SA 50 SS N 8920 0552 MIL-0-44136B OATMEAL COOKIE AND GRA BARS GL F2 924 934 934 A GL SA 50 SS N 8920 0553 MIL-C-44112C CRACKERS FOR...931 A GL 99 GS U B 7320 0872 ANSIZ83 14 GAS FD SV EQ COUNTER APPLI GL G5 B 912 921 922 A GL YD 99 GS U 8 7320 0874 A A XXX CABINET DOUGH PRF 18 PAN

Biopower and Pedagogy: Local Spaces and Institutional Technologies

ERIC Educational Resources Information Center

Wittman, John

2006-01-01

While sitting on a bench outside the university's museum grappling with his own emotional numbness and inability to comprehend the traumatic events of 9-11, John Wittman watched a group of 4 students circling one of the main buildings on campus with an American flag on the back of the roll bar of a truck. Having thought about the flag-waving…

Effects of different roller/crimper designs and rolling speed on rye cover crop termination and seedcotton yield in A no-till system

USDA-ARS?s Scientific Manuscript database

Rollers/crimpers have been utilized in no-till systems to mechanically terminate cover crops as a substitute for chemical termination; however, excessive vibration generated by the original straight bar roller adopted from Brazil has delayed its adoption in the U.S. To reduce excessive vibration, pr...

Simulation of the hot rolling of steel with direct iteration

NASA Astrophysics Data System (ADS)

Hanoglu, Umut; Šarler, Božidar

2017-10-01

In this study a simulation system based on the meshless Local Radial Basis Function Collocation Method (LRBFCM) is applied for the hot rolling of steel. Rolling is a complex, 3D, thermo-mechanical problem; however, 2D cross-sectional slices are used as computational domains that are aligned with the rolling direction and no heat flow or strain is considered in the direction that is orthogonal to the slices. For each predefined position with respect to the rolling direction, the solution procedure is repeated until the slice reaches the final rolling position. Collocation nodes are initially distributed over the domain and boundaries of the initial slice. A local solution is achieved by considering the overlapping influence domains with either 5 or 7 nodes. Radial Basis Functions (RBFs) are used for the temperature discretization in the thermal model and displacement discretization in the mechanical model. The meshless solution procedure does not require a mesh-generation algorithm in the classic sense. Strong-form mechanical and thermal models are run for each slice regarding the contact with the roll's surface. Ideal plastic material behavior is considered for the mechanical results, where the nonlinear stress-strain relation is solved with a direct iteration. The majority of the Finite Element Model (FEM) simulations, including commercial software, use a conventional Newton-Raphson algorithm. However, direct iteration is chosen here due to its better compatibility with meshless methods. In order to overcome any unforeseen stability issues, the redistribution of the nodes by Elliptic Node Generation (ENG) is applied to one or more slices throughout the simulation. The rolling simulation presented here helps the user to design, test and optimize different rolling schedules. The results can be seen minutes after the simulation's start in terms of temperature, displacement, stress and strain fields as well as important technological parameters, like the roll-separating forces, roll toque, etc. An example of a rolling simulation, in which an initial size of 110x110 mm steel is rolled to a round bar with 80 mm diameter, is shown in Fig. 3. A user-friendly computer application for industrial use is created by using the C# and .NET frameworks.

Status of Standardization Projects, Quarter Ending 31 December 1992

DTIC Science & Technology

1992-12-31

B 7320 0872 ANSIZ83 14 GAS FD SV EQ COUNTER APPLI GL G5 B 912 921 922 A GL YD 99 GS U B 7320 0874 A A XXX CABINET DOUGH PRF 18 PAN CAP GL B4 A 914...YD 99 GS N CS 7320 0897 MIL-D-2467F DOUGH ROLLING MACHINES PIE YD H5 924 934 934 A YD 99 N 7320 0898 00-D-2813 DOUGH ROLLING MACHINES PIE YD B4 924...0552 MIL-0-44136B OATMEAL COOKIE AND GRA BARS GL F2 924 934 934 A GL SA 53 SS N 8920 0553 MIL-C-44112C CRACKERS FOR MEAL RTE GL F2 931 941 941 A GL SA

Evaluation of CBS 600 carburized steel as a gear material

NASA Technical Reports Server (NTRS)

Townsend, D. P.; Parker, R. J.; Zaretsky, E. V.

1979-01-01

Gear endurance tests were conducted with one lot of consumable-electrode vacuum-melted (CVM) AISI 9310 gears and one lot of air-melt CBS 600 gears. The gears were 8 pitch with a pitch diameter of 8.89 centimeters (3.5 in.). Bench-type rolling-element fatigue tests were also conducted with one lot of CVM AISI 9310, three lots of CVM CBS 600, and one of air-melt CBS 600 material. The rolling-element bars were 0.952 centimeter (0.375 in.) in diameter. The CBS 600 material exhibited pitting fatigue lives in both rolling-element specimens and gears at least equivalent to that of CVM AISI 9310. Tooth fracture failure occurred with the CBS 600 gears after overrunning a fatigue spall, but it did not occur with the CVM AISI 9310 gears. Tooth fracture in the CBS 600 was attributed to excessive carbon content in the case, excessive case depth, and a higher than normal core hardness.

Multi-objective optimization of process parameters of multi-step shaft formed with cross wedge rolling based on orthogonal test

NASA Astrophysics Data System (ADS)

Han, S. T.; Shu, X. D.; Shchukin, V.; Kozhevnikova, G.

2018-06-01

In order to achieve reasonable process parameters in forming multi-step shaft by cross wedge rolling, the research studied the rolling-forming process multi-step shaft on the DEFORM-3D finite element software. The interactive orthogonal experiment was used to study the effect of the eight parameters, the first section shrinkage rate φ1, the first forming angle α1, the first spreading angle β1, the first spreading length L1, the second section shrinkage rate φ2, the second forming angle α2, the second spreading angle β2 and the second spreading length L2, on the quality of shaft end and the microstructure uniformity. By using the fuzzy mathematics comprehensive evaluation method and the extreme difference analysis, the influence degree of the process parameters on the quality of the multi-step shaft is obtained: β2>φ2L1>α1>β1>φ1>α2L2. The results of the study can provide guidance for obtaining multi-stepped shaft with high mechanical properties and achieving near net forming without stub bar in cross wedge rolling.

Three methods of presenting flight vector information in a head-up display during simulated STOL approaches

NASA Technical Reports Server (NTRS)

Dwyer, J. H., III; Palmer, E. A., III

1975-01-01

A simulator study was conducted to determine the usefulness of adding flight path vector symbology to a head-up display designed to improve glide-slope tracking performance during steep 7.5 deg visual approaches in STOL aircraft. All displays included a fixed attitude symbol, a pitch- and roll-stabilized horizon bar, and a glide-slope reference bar parallel to and 7.5 deg below the horizon bar. The displays differed with respect to the flight-path marker (FPM) symbol: display 1 had no FPM symbol; display 2 had an air-referenced FPM, and display 3 had a ground-referenced FPM. No differences between displays 1 and 2 were found on any of the performance measures. Display 3 was found to decrease height error in the early part of the approach and to reduce descent rate variation over the entire approach. Two measures of workload did not indicate any differences between the displays.

Feeding Concept, Military Vs Civilian System

DTIC Science & Technology

1990-12-01

Pudding d 3 c Chocolate Pudding w/Whipped Topping d 3 c Cowboy Cookies d 3 c Cream Puffs d 3 c Donuts d...c Fruit Won Tons d 3 c Gelatin Cubes d 3 c Hermits d 3 c Ice Box Cookies d : c Ice Cream d...I c Jelly Bar Spritz d 3 c Jelly Roll d : c Lemon Meringue Pie d : c Lime Gelatin Cubes d : c Oatmeal Cookies

Promising Sparingly Alloyed Boron-Bearing Steels for the Production of High-Strength Fasteners

NASA Astrophysics Data System (ADS)

Bobylev, M. V.; Koroleva, E. G.; Shtannikov, P. A.

2005-05-01

The main advantages of boron-bearing steels used for production of rolled sections at cold upset shops of Russian automotive plants are considered. A thermodynamic model for the majority of boron-bearing steels for high-strength fasteners is used to plot nomograms characterizing the effect of titanium, aluminum, nitrogen, and boron on the amount of nitrides and oxides segregated in crystallization and on the content of effective boron. The effect of effective boron on the characteristics of hardenability is estimated. The studies conducted are used for determining the range of permissible contents of titanium and aluminum ensuring through hardenability of rolled bars from steels 12G1R, 20G2R, and 30G1R up to 25 mm in diameter.

High- and Low-Temperature Deformation Behavior of Different Orientation Hot-Rolled Annealed Zircaloy-4

NASA Astrophysics Data System (ADS)

Zong, Yingying; Gen, Qingfeng; Jiang, Hongwei; Shan, Debin; Guo, Bin

2018-03-01

In this paper, the hot-rolled annealed Zircaloy-4 samples with different orientation were subjected to uniaxial compression with a strain rate of 0.001 s-1 to obtain the stress-strain curves of different initial orientation samples at different temperatures. Electron backscatter diffraction (EBSD) technique and transmission electron microscope (TEM) technique were used to analyze the microstructures and textures of compressed samples. The mechanical properties and microstructural evolution of rolling directions (RD), transverse directions (TD) and normal directions (ND) were investigated under the conditions of - 150 °C low temperature, room temperature and 200 °C high temperature (simulated lunar temperature environment). The results show that the strength of Zircaloy-4 decreases with the increase in deformation temperature, and the strength in three orientations is ND > TD > RD. The deformation mechanism of hot-rolled annealed Zircaloy-4 with different orientation is different. In RD, { 10\\bar{1}0} < {a} > prismatic slip has the highest Schmid factor (SF), so it is most easy to activate the slip, followed by TD orientation, and ND orientation is the most difficult to activate. The deformed grains abide slip→twinning→slip rule, and the different orientation Zircaloy-4 deformation mechanisms mainly are the twinning coordinated with the slip.

Continuous overturn control of compactors/rollers by rollover protective structures

PubMed Central

Myers, Melvin L.

2009-01-01

The objective of this article is to report on the effectiveness of Rollover Protective Structures (ROPS) in preventing continuous overturns of compactors/rollers. This study is a case-based analysis of government investigation reports of injury-related overturns of compactors/rollers. The overturns were predominately on construction sites including road and embankment construction in the USA. Other sites included driveway and roadway maintenance or repair and transporting of compactors/rollers either by driving or when loading on or unloading from trailers. The principle intervention observed in controlling a continuous overturn (a roll beyond 90° relative to the impact surface) was the presence of a ROPS on a compactor/roller that serves as an anti-roll bar. The main outcome measures are cases of compactor/roller overturns that are restricted to a 90° roll or are continuous (exceed a 90° roll.) All cases of an overturn in which a ROPS was present resulted in no continuous overturn, and the cases involved with no ROPS averaged an overturn of 301°, showing a propensity for a continuous overturn. This case-based analysis identified a ROPS on compactors/rollers as an effective control for reducing the risk of an overturn to 90° relative to the impact plane. PMID:21765649

Measurement of interfacial thermal conductance in Lithium ion batteries

NASA Astrophysics Data System (ADS)

Gaitonde, Aalok; Nimmagadda, Amulya; Marconnet, Amy

2017-03-01

Increasing usage and recent accidents due to Lithium ion (Li-ion) batteries exploding or catching on fire has inspired research on the thermal management of these batteries. In cylindrical 18650 cells, heat generated during the charge/discharge cycle must dissipate to the surrounding through its metallic case due to the poor thermal conductivity of the jelly roll, which is spirally wound with many interfaces between electrodes and the polymeric separator. This work develops a technique to measure the thermal resistance across the case-separator interface, which ultimately limits heat transfer out of the jelly roll. Commercial 18650 batteries are discharged and opened using a battery disassembly tool, and the 25 μm thick separator and the 200 μm thick metallic case are harvested to make samples. A miniaturized version of the conventional reference bar method (ASTM astm:D5470)

The Warrior Heritage. A Study of Rhodesia.

DTIC Science & Technology

1980-05-01

And then, seconds before impact and certain death, the patrol rises to its feet and, standing shoulder to shoulder, the men shout their last defiance...are the Tusker-Kudu- Rhino series and the Puma-Hippo series. Vehicles of the first series are made from the standard Land Rover, long wheel base frame...bolts. The basic vehicle thus created is then surmounted 92 with either a Rhino , Kudu or Tusker body. Tuskers have a drum-like roll bar cage, covered with

Near net shape processing of continuous lengths of superconducting wire

DOEpatents

Danyluk, Steven; McNallan, Michael; Troendly, Robert; Poeppel, Roger; Goretta, Kenneth; Lanagan, Michael

1997-01-01

A system and method for mechanically forming a ceramic superconductor product. A system for making the ceramic superconductor includes a metallic channel portion having a cross section for receiving a ceramic superconductor powder, a roll to mechanically reduce the channel cross section and included superconductor powder and a cap portion welded to the channel portion using a localized high energy source. The assembled bar is then mechanically reduced to form a tape or wire end product.

The stress corrosion resistance and the cryogenic temperature mechanical properties of hot rolled Nitronic 32 bar material

NASA Technical Reports Server (NTRS)

Montano, J. W. L.

1977-01-01

The ambient and cryogenic temperature mechanical properties and the ambient temperature stress corrosion properties of hot rolled and centerless ground Nitronic 32 stainless steel bar material are presented. The mechanical properties of longitudinal specimens were evaluated at test temperatures from ambient to liquid hydrogen. The tensile test data indicated increasing smooth tensile strength with decreasing temperature to liquid hydrogen temperature. However, below -200 F (-129.0 C) the notched tensile strength decreased slightly and below -320 F (-196.0 C) the decrease was significant. The elongation and reduction of area decreased drastically at temperatures below -200 F (-129.0 C). The Charpy V-notched impact energy decreased steadily with decreasing test temperature. Stress corrosion tests were performed on longitudinal tensile specimens stressed to 0, 75, and 90 percent of the 0.2 percent yield strength and on transverse 'C'-ring specimens stressed to 75 and 90 percent of the yield strength and exposed to: alternate immersion in a 3.5 percent NaCl bath, humidity cabinet environment, and a 5 percent salt spray atmosphere. The longitudinal tensile specimens experienced no corrosive attack; however, the 'C'-rings exposed to the alternate immersion and to the salt spray experienced some shallow etching and pitting, respectively. Small cracks appeared in two of the 'C'-rings after one month exposure to the salt spray.

Texture Evolution in a Ti-Ta-Nb Alloy Processed by Severe Plastic Deformation

NASA Astrophysics Data System (ADS)

Cojocaru, Vasile-Danut; Raducanu, Doina; Gloriant, Thierry; Cinca, Ion

2012-05-01

Titanium alloys are extensively used in a variety of applications because of their good mechanical properties, high biocompatibility, and corrosion resistance. Recently, β-type Ti alloys containing Ta and Nb have received much attention because they feature not only high specific strength but also biocorrosion resistance, no allergic problems, and biocompatibility. A Ti-25Ta-25Nb β-type titanium alloy was subjected to severe plastic deformation (SPD) processing by accumulative roll bonding and investigated with the aim to observe the texture developed during SPD processing. Texture data expressed by pole figures, inverse pole figures, and orientation distribution functions for the (110), (200), and (211) β-Ti peaks were obtained by XRD investigations. The results showed that it is possible to obtain high-intensity share texture modes ({001}<110>) and well-developed α and γ-fibers; the most important fiber is the α-fiber ({001} < {1bar{1}0} > to {114} < {1bar{1}0} > to {112} < {1bar{1}0} > ). High-intensity texture along certain crystallographic directions represents a way to obtain materials with high anisotropic properties.

The LivePhoto Physics videos and video analysis site

NASA Astrophysics Data System (ADS)

Abbott, David

2009-09-01

The LivePhoto site is similar to an archive of short films for video analysis. Some videos have Flash tools for analyzing the video embedded in the movie. Most of the videos address mechanics topics with titles like Rolling Pencil (check this one out for pedagogy and content knowledge—nicely done!), Juggler, Yo-yo, Puck and Bar (this one is an inelastic collision with rotation), but there are a few titles in other areas (E&M, waves, thermo, etc.).

Near net shape processing of continuous lengths of superconducting wire

DOEpatents

Danyluk, S.; McNallan, M.; Troendly, R.; Poeppel, R.; Goretta, K.; Lanagan, M.

1997-08-26

A system and method for mechanically forming a ceramic superconductor product are disclosed. A system for making the ceramic superconductor includes a metallic channel portion having a cross section for receiving a ceramic superconductor powder, a roll to mechanically reduce the channel cross section and included superconductor powder and a cap portion welded to the channel portion using a localized high energy source. The assembled bar is then mechanically reduced to form a tape or wire end product. 9 figs.

Human perceptual overestimation of whole body roll tilt in hypergravity

PubMed Central

Newman, Michael C.; Oman, Charles M.; Merfeld, Daniel M.; Young, Laurence R.

2014-01-01

Hypergravity provides a unique environment to study human perception of orientation. We utilized a long-radius centrifuge to study perception of both static and dynamic whole body roll tilt in hypergravity, across a range of angles, frequencies, and net gravito-inertial levels (referred to as G levels). While studies of static tilt perception in hypergravity have been published, this is the first to measure dynamic tilt perception (i.e., with time-varying canal stimulation) in hypergravity using a continuous matching task. In complete darkness, subjects reported their orientation perception using a haptic task, whereby they attempted to align a hand-held bar with their perceived horizontal. Static roll tilt was overestimated in hypergravity, with more overestimation at larger angles and higher G levels, across the conditions tested (overestimated by ∼35% per additional G level, P < 0.001). As our primary contribution, we show that dynamic roll tilt was also consistently overestimated in hypergravity (P < 0.001) at all angles and frequencies tested, again with more overestimation at higher G levels. The overestimation was similar to that for static tilts at low angular velocities but decreased at higher angular velocities (P = 0.006), consistent with semicircular canal sensory integration. To match our findings, we propose a modification to a previous Observer-type canal-otolith interaction model. Specifically, our data were better modeled by including the hypothesis that the central nervous system treats otolith stimulation in the utricular plane differently than stimulation out of the utricular plane. This modified model was able to simulate quantitatively both the static and the dynamic roll tilt overestimation in hypergravity measured experimentally. PMID:25540216

Rhenium material properties

NASA Technical Reports Server (NTRS)

Biaglow, James A.

1995-01-01

Tensile data were obtained from four different types of rhenium at ambient and elevated temperatures. The four types of rhenium included chemical vapor deposition (CVD) and three powder metallurgy (PM) types, i.e., rolled sheet and pressed and sintered bars, with and without hot isostatic pressure (HIP) treatment. Results revealed a wide range of values with ultimate strengths at ambient temperatures varying from 663 MPa for CVD rhenium to 943 MPa for rolled sheet. A similar spread was also obtained for material tested at 1088 K and 1644 K. The wide variance observed with the different materials indicated that the rhenium manufacturing process, material composition and prior handling strongly dictated its properties. In addition to tensile properties, CVD, pressed and sintered material and HIP rhenium successfully completed 100 cycles of low cycle fatigue. Creep data were also obtained showing that CVD and pressed and sintered rhenium could sustain five hours of testing under a tension of 27.5 MPa at 1922 K.

Evaluation of rolling contact fatigue of induction heated 13Cr-2Ni-2Mo Stainless steel bar with Si3N4-ball

NASA Astrophysics Data System (ADS)

Yadoiwa, Ariyasu; Mizobe, Koshiro; Kida, Katsuyuki

2018-03-01

13Cr % martensitic stainless steels were used in various industry, because they have excellent corrosion resistance and high hardness among other stainless steels. They are also expected as a bearing material, however, the research on rolling contact fatigue (RCF) is not enough. In this study, 13Cr-2Ni-2Mo stainless steels were quenched by induction heating and their RCF lives were evaluated. A Si3N4-ball was used in order to apply higher stress (Pmax = 5.6 GPa) than our previous tests (Pmax=5.3 GPa), in a single-ball RCF testing machine. It was found that the basic life (L10) was 2.20×106 cycles and Median life (L50) was 6.04×106 cycles. In addition, Weibull modulus became higher than the previous tests.

Total knee replacement with natural rollback.

PubMed

Wachowski, Martin Michael; Walde, Tim Alexander; Balcarek, Peter; Schüttrumpf, Jan Philipp; Frosch, Stephan; Stauffenberg, Caspar; Frosch, Karl-Heinz; Fiedler, Christoph; Fanghänel, Jochen; Kubein-Meesenburg, Dietmar; Nägerl, Hans

2012-03-20

A novel class of total knee replacement (AEQUOS G1) is introduced which features a unique design of the articular surfaces. Based on the anatomy of the human knee and differing from all other prostheses, the lateral tibial "plateau" is convexly curved and the lateral femoral condyle is posteriorly shifted in relation to the medial femoral condyle. Under compressive forces the configuration of the articular surfaces of human knees constrains the relative motion of femur and tibia in flexion/extension. This constrained motion is equivalent to that of a four-bar linkage, the virtual 4 pivots of which are given by the centres of curvature of the articulating surfaces. The dimensions of the four-bar linkage were optimized to the effect that constrained motion of the total knee replacement (TKR) follows the flexional motion of the human knee in close approximation, particularly during gait. In pilot studies lateral X-ray pictures have demonstrated that AEQUOS G1 can feature the natural rollback in vivo. Rollback relieves the load of the patello-femoral joint and minimizes retropatellar pressure. This mechanism should reduce the prevalence of anterior knee pain. The articulating surfaces roll predominantly in the stance phase. Consequently sliding friction is replaced by the lesser rolling friction under load. Producing rollback should minimize material wear due to friction and maximize the lifetime of the prosthesis. To definitely confirm these theses one has to wait for the long term results. Copyright © 2011 Elsevier GmbH. All rights reserved.

Microstructure and properties of thermomechanically strengthened reinforcement bars: A comparative assessment of plain-carbon and low-alloy steel grades

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ray, A.; Mukerjee, D.; Sen, S.K.

1997-06-01

An extensive investigation has been carried out to study structure-property characteristics and corrosion behavior in three varieties of thermomechanically treated (TMT) reinforcement bars (rebars) produced in an integrated steel plant under the Steel Authority of India Limited. Three experimental steel heats--one of plain-carbon and two of low-alloy chemistry--were chosen for the study. Of the two low-alloy heats, one was copper-bearing and the other contained both copper and chromium for improved corrosion resistance. Hot-rolled bars for each specific chemistry were subjected to in-line thermomechanical treatment, where quenching parameters were altered to achieve different yield strength levels. All the TMT rebars, regardlessmore » of chemistry and strength level, exhibited a composite microstructure consisting of ferrite-pearlite at the core and tempered martensite at the rim. Although a tendency toward formation of Widmanstaetten ferrite was evident in bars of 500 and 550 MPa yield strength levels, no adverse effect on their strength and ductility was observed. From the standpoint of mechanical properties, the rebars not only conformed to minimum yield strength requirements, but also exhibited high elongation values (21 to 28%) and excellent bendability. Corrosion studies of both TMT and cold-twisted and deformed (CTD) rebars subjected to different laboratory tests indicated that corrosion resistance increased in this order: CTD, plain-carbon TMT, copper-bearing TMT, and copper/chromium-bearing TMT.« less

Neural and Neural Gray-Box Modeling for Entry Temperature Prediction in a Hot Strip Mill

NASA Astrophysics Data System (ADS)

Barrios, José Angel; Torres-Alvarado, Miguel; Cavazos, Alberto; Leduc, Luis

2011-10-01

In hot strip mills, initial controller set points have to be calculated before the steel bar enters the mill. Calculations rely on the good knowledge of rolling variables. Measurements are available only after the bar has entered the mill, and therefore they have to be estimated. Estimation of process variables, particularly that of temperature, is of crucial importance for the bar front section to fulfill quality requirements, and the same must be performed in the shortest possible time to preserve heat. Currently, temperature estimation is performed by physical modeling; however, it is highly affected by measurement uncertainties, variations in the incoming bar conditions, and final product changes. In order to overcome these problems, artificial intelligence techniques such as artificial neural networks and fuzzy logic have been proposed. In this article, neural network-based systems, including neural-based Gray-Box models, are applied to estimate scale breaker entry temperature, given its importance, and their performance is compared to that of the physical model used in plant. Several neural systems and several neural-based Gray-Box models are designed and tested with real data. Taking advantage of the flexibility of neural networks for input incorporation, several factors which are believed to have influence on the process are also tested. The systems proposed in this study were proven to have better performance indexes and hence better prediction capabilities than the physical models currently used in plant.

High-Performance Flexible All-Solid-State Supercapacitor from Large Free-Standing Graphene-PEDOT/PSS Films.

PubMed

Liu, Yuqing; Weng, Bo; Razal, Joselito M; Xu, Qun; Zhao, Chen; Hou, Yuyang; Seyedin, Shayan; Jalili, Rouhollah; Wallace, Gordon G; Chen, Jun

2015-11-20

Although great attention has been paid to wearable electronic devices in recent years, flexible lightweight batteries or supercapacitors with high performance are still not readily available due to the limitations of the flexible electrode inventory. In this work, highly flexible, bendable and conductive rGO-PEDOT/PSS films were prepared using a simple bar-coating method. The assembled device using rGO-PEDOT/PSS electrode could be bent and rolled up without any decrease in electrochemical performance. A relatively high areal capacitance of 448 mF cm(-2) was achieved at a scan rate of 10 mV s(-1) using the composite electrode with a high mass loading (8.49 mg cm(-2)), indicating the potential to be used in practical applications. To demonstrate this applicability, a roll-up supercapacitor device was constructed, which illustrated the operation of a green LED light for 20 seconds when fully charged.

High-Performance Flexible All-Solid-State Supercapacitor from Large Free-Standing Graphene-PEDOT/PSS Films

NASA Astrophysics Data System (ADS)

Liu, Yuqing; Weng, Bo; Razal, Joselito M.; Xu, Qun; Zhao, Chen; Hou, Yuyang; Seyedin, Shayan; Jalili, Rouhollah; Wallace, Gordon G.; Chen, Jun

2015-11-01

Although great attention has been paid to wearable electronic devices in recent years, flexible lightweight batteries or supercapacitors with high performance are still not readily available due to the limitations of the flexible electrode inventory. In this work, highly flexible, bendable and conductive rGO-PEDOT/PSS films were prepared using a simple bar-coating method. The assembled device using rGO-PEDOT/PSS electrode could be bent and rolled up without any decrease in electrochemical performance. A relatively high areal capacitance of 448 mF cm-2 was achieved at a scan rate of 10 mV s-1 using the composite electrode with a high mass loading (8.49 mg cm-2), indicating the potential to be used in practical applications. To demonstrate this applicability, a roll-up supercapacitor device was constructed, which illustrated the operation of a green LED light for 20 seconds when fully charged.

Numerical proof of stability of roll waves in the small-amplitude limit for inclined thin film flow

NASA Astrophysics Data System (ADS)

Barker, Blake

2014-10-01

We present a rigorous numerical proof based on interval arithmetic computations categorizing the linearized and nonlinear stability of periodic viscous roll waves of the KdV-KS equation modeling weakly unstable flow of a thin fluid film on an incline in the small-amplitude KdV limit. The argument proceeds by verification of a stability condition derived by Bar-Nepomnyashchy and Johnson-Noble-Rodrigues-Zumbrun involving inner products of various elliptic functions arising through the KdV equation. One key point in the analysis is a bootstrap argument balancing the extremely poor sup norm bounds for these functions against the extremely good convergence properties for analytic interpolation in order to obtain a feasible computation time. Another is the way of handling analytic interpolation in several variables by a two-step process carving up the parameter space into manageable pieces for rigorous evaluation. These and other general aspects of the analysis should serve as blueprints for more general analyses of spectral stability.

Characterizing the Performance of the Wheel Electrostatic Spectrometer

NASA Technical Reports Server (NTRS)

Johansen, Michael R.; Mackey, P. J.; Holbert, E.; Calle, C. I.; Clements, J. S.

2013-01-01

Insulators need to be discharged after each wheel revolution. Sensor responses repeatable within one standard deviation in the noise of the signal. Insulators may not need to be cleaned after each revolution. Parent Technology- Mars Environmental Compatibility Assessment/Electrometer Electrostatic sensors with dissimilar cover insulators Protruding insulators tribocharge against regolith simulant Developed for use on the scoop for the 2001 Mars Odyssey lander Wheel Electrostatic Spectrometer Embedded electrostatic sensors in prototype Martian rover wheel If successful, this technology will enable constant electrostatic testing on Mars Air ionizing fan used to neutralize the surface charge on cover insulators . WES rolled on JSClA lunar simulant Control experiment -Static elimination not conducted between trials -Capacitor discharged after each experiment Charge neutralization experiment -Static elimination conducted between trials -Capacitor discharged after each experiment. Air ionizing fan used on insulators after each wheel revolution Capacitor discharged after each trial Care was taken to roll WES with same speed/pressure Error bars represent one standard deviation in the noise of e ach sensor

Parametrically excited motion of a levitated rigid bar over high- Tc superconducting bulks

NASA Astrophysics Data System (ADS)

Shimizu, T.; Sugiura, T.; Ogawa, S.

2006-10-01

High-Tc superconducting levitation systems achieve, under no contact support, stable levitation without control. This feature can be applied to flywheels, magnetically levitated trains, and so on. But no contact support has small damping. So these mechanisms can show complicated phenomena of dynamics due to nonlinearity in their magnetic force. For application to large-scale machines, we need to analyze dynamics of a large levitated body supported at multiple points. This research deals with nonlinearly coupled oscillation of a homogeneous and symmetric rigid bar supported at its both ends by equal electromagnetic forces between superconductors and permanent magnets. In our past study, using a rigid bar, we found combination resonance. Combination resonance happens owing to the asymmetry of the system. But, even if support forces are symmetric, parametric resonance can happen. With a simple symmetric model, this research focuses on especially the parametric resonance, and evaluates nonlinear effect of the symmetric support forces by experiment and numerical analysis. Obtained results show that two modes, caused by coupling of horizontal translation and roll motion, can be excited nonlinearly when the superconductor is excited vertically in the neighborhood of twice the natural frequencies of those modes. We confirmed these resonances have nonlinear characteristics of soft-spring, hysteresis and so on.

Design and stable flight of a 21 g insect-like tailless flapping wing micro air vehicle with angular rates feedback control.

PubMed

Phan, Hoang Vu; Kang, Taesam; Park, Hoon Cheol

2017-04-04

An insect-like tailless flapping wing micro air vehicle (FW-MAV) without feedback control eventually becomes unstable after takeoff. Flying an insect-like tailless FW-MAV is more challenging than flying a bird-like tailed FW-MAV, due to the difference in control principles. This work introduces the design and controlled flight of an insect-like tailless FW-MAV, named KUBeetle. A combination of four-bar linkage and pulley-string mechanisms was used to develop a lightweight flapping mechanism that could achieve a high flapping amplitude of approximately 190°. Clap-and-flings at dorsal and ventral stroke reversals were implemented to enhance vertical force. In the absence of a control surface at the tail, adjustment of the location of the trailing edges at the wing roots to modulate the rotational angle of the wings was used to generate control moments for the attitude control. Measurements by a 6-axis load cell showed that the control mechanism produced reasonable pitch, roll and yaw moments according to the corresponding control inputs. The control mechanism was integrated with three sub-micro servos to realize the pitch, roll and yaw controls. A simple PD feedback controller was implemented for flight stability with an onboard microcontroller and a gyroscope that sensed the pitch, roll and yaw rates. Several flight tests demonstrated that the tailless KUBeetle could successfully perform a vertical climb, then hover and loiter within a 0.3 m ground radius with small variations in pitch and roll body angles.

Ancestral QTL Alleles from Wild Emmer Wheat Enhance Root Development under Drought in Modern Wheat.

PubMed

Merchuk-Ovnat, Lianne; Fahima, Tzion; Ephrath, Jhonathan E; Krugman, Tamar; Saranga, Yehoshua

2017-01-01

A near-isogenic line (NIL-7A-B-2), introgressed with a quantitative trait locus (QTL) on chromosome 7AS from wild emmer wheat ( Triticum turgidum ssp. dicoccoides ) into the background of bread wheat ( T. aestivum L.) cv. BarNir, was recently developed and studied in our lab. NIL-7A-B-2 exhibited better productivity and photosynthetic capacity than its recurrent parent across a range of environments. Here we tested the hypothesis that root-system modifications play a major role in NIL-7A-B-2's agronomical superiority. Root-system architecture (dry matter and projected surface area) and shoot parameters of NIL-7A-B-2 and 'BarNir' were evaluated at 40, 62, and 82 days after planting (DAP) in a sand-tube experiment, and root tip number was assessed in a 'cigar-roll' seedling experiment, both under well-watered and water-limited (WL) treatments. At 82 DAP, under WL treatment, NIL-7A-B-2 presented greater investment in deep roots (depth 40-100 cm) than 'BarNir,' with the most pronounced effect recorded in the 60-80 cm soil depth (60 and 40% increase for root dry matter and surface area, respectively). NIL-7A-B-2 had significantly higher root-tip numbers (∼48%) per plant than 'BarNir' under both treatments. These results suggest that the introgression of 7AS QTL from wild emmer wheat induced a deeper root system under progressive water stress, which may enhance abiotic stress resistance and productivity of domesticated wheat.

Optical fiber sensor based on a polymer optical fiber macro-bend to study thermal expansion of metals

NASA Astrophysics Data System (ADS)

Pakdeevanich, Paradorn

2018-05-01

Thermal expansion is an important parameter for characterization of metals. As metal is heated, the molecules vibrate more violently and expand in all direction. Investigators have focused to study the thermal strain. However, the amount of expansion is difficult to measure. An attempt has been made to develop an apparatus using optical technique. The principle of this system is the transformation of length changes into changes of light intensity. The purpose of this work is to design and develop an optical fiber sensor based on a macro-bend of a polymer optical fiber. In this system, thermal expansion of metal was converted into the rolling of a needle in which placed beneath a flat bar of metal. Optical fiber sensor was attached to the ended section of a needle. As the crimp tube of the fiber sensor was moved due to thermal expansion of metal, the bend radii of optical fiber sensor was changed. As a sequence, the loss induced by the bending effect was depended on the expansion of metal that changed with temperature. In this study, we utilized optical fiber sensor to monitor and compare the thermal expansion of copper, brass and aluminum. According to our experimental results, the linear response with temperature was reported. The measured values of coefficient of thermal expansion was analyzed to be 0.45, 0.35 and 0.32 a.u./°C for aluminum bar, brass bar and copper bar, respectively. In addition, the effect of the size of the diameter of a needle on the response of bending loss was investigated.

Processing and microstructure of Nb-1 percent Zr-0.1 percent C alloy sheet

NASA Technical Reports Server (NTRS)

Uz, Mehmet; Titran, Robert H.

1992-01-01

A systematic study was carried out to evaluate the effects of processing on the microstructure of Nb-1 wt. pct. Zr-0.1 wt. pct. C alloy sheet. The samples were fabricated by cold rolling different sheet bars that were single-, double- or triple-extruded at 1900 K. Heat treatment consisted on one- or two-step annealing of different samples at temperatures ranging from 1350 to 1850 K. The assessment of the effects of processing on microstructure involved characterization of the precipitates including the type, crystal structure, chemistry and distribution within the material as well as an examination of the grain structure. A combination of various analytical and metallographic techniques were used on both the sheet samples and the residue extracted from them. The results show that the relatively coarse orthorhombic Nb2C carbides in the as-rolled samples transformed to rather fine cubic monocarbides of Nb and Zr with varying Zr/Nb ratios upon subsequent heat treatment. The relative amount of the cubic carbides and the Zr/Nb ratio increased with increasing number of extrusions prior to cold rolling. Furthermore, the size and the aspect ratio of the grains appear to be strong functions of the processing history of the material. These and other results obtained will be presented with the emphasis on a possible relationship between processing and microstructure.

Influence of repeated quenching-tempering on spheroidized carbide area in JIS SUJ2 bearing steel

NASA Astrophysics Data System (ADS)

Egawa, K.; Yoshida, I.; Yoshida, H.; Mizobe, K.; Kida, K.

2018-02-01

High-carbon high-strength JIS-SUJ2 bearing steel is mainly used for rolling contact applications which require high fatigue strength. We had applied repeated quenching which refine the prior austenite grains to this steel. In this work, we prepared JIS SUJ2 bearing steel bar specimens which were quenched three times (Q3T1) and quenched-tempered three times (QTQTQT) in order to investigate the influence of tempering before quenching on the microstructure. The specimens were etched by picral to observe the microstructure. We found that the spheroidized carbide area was important for the prior austenite grain formation.

Computerized Analysis of Nutrients (CAN) System

DTIC Science & Technology

1989-11-01

1 H 24.02 PEANUT BUTTER BARS (Sugar Cookie Mix) 3.1 1 PIE CRUST 3 I 1.01. PIE CRUST ( Dough Rolling Method) 3 I 1.02 PIE CRUST (Manual Method) 3 I 2... COOKIES -CHOC COV MR6801 6 .0 .0 99.0 PEANUT BUTTER MRE & MR6906 6 .0 .0 99.0 SOUR CREAM 801056 5 .0 .0 99.0 PINEAPPLE CANNED IN 809268 5 .0 .0 99.1...CHOCOLATE CO MR6803 3 .0 .0 99.6 CAKE-CHERRY NUT MR6804 3 .0 .0 99.6 COOKIES , OREO OREO 3 .0 .0 99.7 SODA FRUIT 004060 2 .0 .0 99.7 OLIVE-GREEN 014060

Force and Strength Analysis of the Reel with Jaw of Torsion-bar Spring

NASA Astrophysics Data System (ADS)

Ma, Ke; Liu, Weiqi; Wang, Jiawei; Gu, Le

2017-06-01

Structure characteristics and working principle of the reel with jaw of torsion-bar spring are introduced. The reel can not only eliminate the leakage risks of hydraulic jaw, but also reduce the investment cost of enterprises and improve the surface quality of the products. The static analysis of mandrel, sector plate and oblique wedge were conducted, and the main data of stress distribution and deformation were obtained, which provide a reliable theoretical basis for the design and optimization of the reel. The research results show that the external support has a great effect on the stress and deformation of the mandrel. With the increase of the weight of steel stress increases, the drum deformation increases, but the analysis of the position of maximum stress, can be obtained to drum stress and deformation is the main reason of excessive bending moment caused by heavy steel rolls. The bending moment and deformation can be reduced significantly at the end of the steel coil, which can effectively improve the service life of the drum.

Phased in smoke-free workplace laws: impact in grass-roots pubs and clubs in South Australia.

PubMed

Miller, Caroline L; Hickling, Jacqueline A

2007-04-01

Smoke-free workplace laws with phase-in provisions for licensed bar and gaming venues are being rolled-out across Australia. This study investigates grass-roots industry reactions after the first phase of implementation in South Australia and compares them with views of patrons who smoke. Two surveys were conducted with bar and club managers of randomly selected licensed venues in South Australia. The first survey (baseline) was conducted in November 2004 (n=500; by telephone). The second survey (phase 1) was conducted in May 2005 (n=357; in person including site inspection). Community support was assessed in a telephone survey conducted in 2005 (n=2,004). In 2005, more than half supported the smoking bans planned for 2007 and up to 75% supported the phase-in provisions (for 2005-07). By 2005, 90.7% recognised it was important to provide a smoke-free environment for staff, but one-third were under the mistaken impression that phase-in measures offered health protection. Attempted compliance was very high and, for most, not an effort or financial burden. Verified compliance was fair, although lower than self-report due to confusion about rules for smoking and non-smoking areas. When the views of bar and club managers were compared with community views, collected in a separate survey, it was found that bar and club managers substantially under-estimated community support for impending total smoke-free laws, due in November 2007. Grass-roots industry support for smoke-free laws is considerable and higher than industry comments might imply, but somewhat lesser than community support. Attempted compliance is fair, despite confusion about details.

Instrumented roll technology for the design space development of roller compaction process.

PubMed

Nesarikar, Vishwas V; Vatsaraj, Nipa; Patel, Chandrakant; Early, William; Pandey, Preetanshu; Sprockel, Omar; Gao, Zhihui; Jerzewski, Robert; Miller, Ronald; Levin, Michael

2012-04-15

Instrumented roll technology on Alexanderwerk WP120 roller compactor was developed and utilized successfully for the measurement of normal stress on ribbon during the process. The effects of process parameters such as roll speed (4-12 rpm), feed screw speed (19-53 rpm), and hydraulic roll pressure (40-70 bar) on normal stress and ribbon density were studied using placebo and active pre-blends. The placebo blend consisted of 1:1 ratio of microcrystalline cellulose PH102 and anhydrous lactose with sodium croscarmellose, colloidal silicon dioxide, and magnesium stearate. The active pre-blends were prepared using various combinations of one active ingredient (3-17%, w/w) and lubricant (0.1-0.9%, w/w) levels with remaining excipients same as placebo. Three force transducers (load cells) were installed linearly along the width of the roll, equidistant from each other with one transducer located in the center. Normal stress values recorded by side sensors and were lower than normal stress values recorded by middle sensor and showed greater variability than middle sensor. Normal stress was found to be directly proportional to hydraulic pressure and inversely to screw to roll speed ratio. For active pre-blends, normal stress was also a function of compressibility. For placebo pre-blends, ribbon density increased as normal stress increased. For active pre-blends, in addition to normal stress, ribbon density was also a function of gap. Models developed using placebo were found to predict ribbon densities of active blends with good accuracy and the prediction error decreased as the drug concentration of active blend decreased. Effective angle of internal friction and compressibility properties of active pre blend may be used as key indicators for predicting ribbon densities of active blend using placebo ribbon density model. Feasibility of on-line prediction of ribbon density during roller compaction was demonstrated using porosity-pressure data of pre-blend and normal stress measurements. Effect of vacuum to de-aerate pre blend prior to entering the nip zone was studied. Varying levels of vacuum for de-aeration of placebo pre blend did not affect the normal stress values. However, turning off vacuum completely caused an increase in normal stress with subsequent decrease in gap. Use of instrumented roll demonstrated potential to reduce the number of DOE runs by enhancing fundamental understanding of relationship between normal stress on ribbon and process parameters. Copyright © 2012 Elsevier B.V. All rights reserved.

Dynamic Behavior of a Rare-Earth-Containing Mg Alloy, WE43B-T5, Plate with Comparison to Conventional Alloy, AM30-F

NASA Astrophysics Data System (ADS)

Agnew, Sean; Whittington, Wilburn; Oppedal, Andrew; El Kadiri, Haitham; Shaeffer, Matthew; Ramesh, K. T.; Bhattacharyya, Jishnu; Delorme, Rick; Davis, Bruce

2014-01-01

The dynamic behavior of Mg alloys is an area of interest for applications such as crash-sensitive automotive components and armor. The rare-earth element-containing alloy WE43B-T5 has performed well in ballistic testing, so the quasi-static (~10-3 1/s) and dynamic (~600-5000 1/s) mechanical behaviors of two Mg alloys, rolled WE43B-T5 and extruded AM30-F, were investigated using servohydraulic and Kolsky bar testing in uniaxial tension and compression. The yield stress was surprisingly isotropic for WE43B-T5 relative to conventional Mg alloys (including extruded AM30-F). The WE43B plate was textured; however, it was not the typical basal texture of hot-rolled Mg-Al alloys. The effect of strain rate on the yield strength of WE43B-T5 is small and the strain-hardening behavior is only mildly rate sensitive (m = 0.008). The combination of high strength (~300 MPa), moderate ductility (0.07-0.20), and low density yield a material with good specific energy absorption capacity.

Influence of Hot-Working Conditions on High-Temperature Properties of a Heat-Resistant Alloy

NASA Technical Reports Server (NTRS)

Ewing, John F; Freeman, J W

1957-01-01

The relationships between conditions of hot-working and properties at high temperatures and the influence of the hot-working on response to heat treatment were investigated for an alloy containing nominally 20 percent molybdenum, 2 percent tungsten, and 1 percent columbium. Commercially produced bar stock was solution-treated at 2,200 degrees F. to minimize prior-history effects and then rolled at temperatures of 2,200 degrees, 2,100 degrees, 2,000 degrees, 1,800 degrees, and 1,600 degrees F. Working was carried out at constant temperature and with incremental decreases in temperature simulating a falling temperature during hot-working. In addition, a few special repeated cyclic conditions involving a small reduction at high temperature followed by a small reduction at a low temperature were used to study the possibility of inducing very low strengths by the extensive precipitation accompanying such properties. Most of the rolling was done in open passes with a few check tests being made with closed passes. Heat treatments at both 2,050 degrees and 2,200 degrees F. subsequent to working were used to study the influence on response to heat treatment.

Deformation mechanism study of a hot rolled Zr-2.5Nb alloy by transmission electron microscopy. II. In situ transmission electron microscopy study of deformation mechanism change of a Zr-2.5Nb alloy upon heavy ion irradiation.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Long, Fei; Daymond, Mark R.; Yao, Zhongwen

2015-03-14

The effect of heavy-ion irradiation on deformation mechanisms of a Zr-2.5Nb alloy was investigated by using the in situ transmission electron microscopy deformation technique. The gliding behavior of prismatic < a > dislocations has been dynamically observed before and after irradiation at room temperature and 300 degrees C. Irradiation induced loops were shown to strongly pin the gliding dislocations. Unpinning occurred while loops were incorporated into or eliminated by < a > dislocations. In the irradiated sample, loop depleted areas with a boundary parallel to the basal plane trace were found by post-mortem observation after room temperature deformation, supporting themore » possibility of basal channel formation in bulk neutron irradiated samples. Strong activity of pyramidal slip was also observed at both temperatures, which might be another important mechanism to induce plastic instability in irradiated zirconium alloys. Finally, {01 (1) over bar1}< 0 (1) over bar 12 > twinning was identified in the irradiated sample deformed at 300 degrees C.« less

Calculation of Crystallographic Texture of BCC Steels During Cold Rolling

NASA Astrophysics Data System (ADS)

Das, Arpan

2017-05-01

BCC alloys commonly tend to develop strong fibre textures and often represent as isointensity diagrams in φ 1 sections or by fibre diagrams. Alpha fibre in bcc steels is generally characterised by <110> crystallographic axis parallel to the rolling direction. The objective of present research is to correlate carbon content, carbide dispersion, rolling reduction, Euler angles (ϕ) (when φ 1 = 0° and φ 2 = 45° along alpha fibre) and the resulting alpha fibre texture orientation intensity. In the present research, Bayesian neural computation has been employed to correlate these and compare with the existing feed-forward neural network model comprehensively. Excellent match to the measured texture data within the bounding box of texture training data set has been already predicted through the feed-forward neural network model by other researchers. Feed-forward neural network prediction outside the bounds of training texture data showed deviations from the expected values. Currently, Bayesian computation has been similarly applied to confirm that the predictions are reasonable in the context of basic metallurgical principles, and matched better outside the bounds of training texture data set than the reported feed-forward neural network. Bayesian computation puts error bars on predicted values and allows significance of each individual parameters to be estimated. Additionally, it is also possible by Bayesian computation to estimate the isolated influence of particular variable such as carbon concentration, which exactly cannot in practice be varied independently. This shows the ability of the Bayesian neural network to examine the new phenomenon in situations where the data cannot be accessed through experiments.

Rayleigh-Benard Convection in a Fluid with Prandtl Number Near One

NASA Astrophysics Data System (ADS)

Hu, Yuchou

1995-01-01

Studies of Rayleigh-Benard convection rotated about a vertical axis in cylindrical geometries with the shadowgraph imaging method are reported. The convection cells had radius-to-height ratios Gamma of between 23 and 52. The working fluid was CO _2 at 16 to 32 bar with Prandtl numbers ranging from 0.85 to 0.98. The results at zero rotation are presented first. For one of the cells (Gamma = 43), axisymmetric convection rolls were stable above onset up to epsilonequivDelta T/Delta T_{c}-1=0.19, where Delta T_{c} is the critical temperature difference. The amplitude of the center of the concentric patterns, the umbilicus, much larger near onset than that of the outlying region, grew as epsilon^{beta_ 1}, with beta_1=0.27 +/-0.04. Outside the umbilicus, the amplitude grew as epsilon^{beta_2 }, with beta_2 = 0.48 +/- 0.04. Pattern dynamics, wavenumbers, spatially-averaged roll-curvature, and sidewall roll-orientation as a function of epsilon are presented for a Gamma = 40 cell. As epsilon was increased, the skewed-varicose instability was first observed at epsilon~ 0.09, and roll -nucleating sidewall-foci were seen for epsilon _sp{~}{>} 0.15. The average roll curvature remained relatively constant for 0.2 _sp{~} {<} epsilon _sp{ ~}{<} 0.5, contrary to general expectation of increasing curvature with epsilon . Spiral-defect chaos appeared at epsilon ~ 0.55. Coincident with the increase in spiral-defect activity was a decrease in the average wavenumber and a marked increase in the sidewall-foci roll -nucleation frequency and average roll curvature. The thresholds of the onset of spiral-defect chaos for Gamma = 28, 40, and 52 were all at epsilon ~ 0.55. For rotating convection, pattern evolution at Gamma = 40 are described for dimensionless rotation rate Omega up to 20 and compared with observations at zero rotation. The Kuppers -Lortz instability was observed at the onset of convection at Omega~9 and co-existed with the skewed-varicose instability. For Omega _sp{~}{<} 11, the Kuppers-Lortz instability occurred via propagation of fronts initiated near the sidewall whereas at higher Omega fronts appearing spontaneously away from the sidewall became dominant. For Omega _sp{~}{>} 13, the Kuppers-Lortz angle was 60^{ circ}+/-1^{circ} , and the time scaling of the pattern dynamics showed a power-law dependence on epsilon with an exponent of 0.6 +/- 0.1. The threshold for spiral-defect chaos was depressed by rotation with spirals appearing at epsilon~0.40 at Omega = 8.8. The preferential inward-winding direction of the spirals was the same as the direction of the system rotation. The average wavenumber at onset of convection agreed with theoretical calculations and decreased with increasing epsilon. Quantitative measurements of the sidewall obliqueness show a general trend of rolls ending less perpendicular to the sidewall with increasing Omega for Omega<=q 9.

Free-to-Roll Testing of Airplane Models in Wind Tunnels

NASA Technical Reports Server (NTRS)

Capone, Francis J.; Owens, D. Bruce; Hall, Robert M.

2007-01-01

A free-to-roll (FTR) test technique and test rig make it possible to evaluate both the transonic performance and the wingdrop/ rock behavior of a high-strength airplane model in a single wind-tunnel entry. The free-to-roll test technique is a single degree-of-motion method in which the model is free to roll about the longitudinal axis. The rolling motion is observed, recorded, and analyzed to gain insight into wing-drop/rock behavior. Wing-drop/rock is one of several phenomena symptomatic of abrupt wing stall. FTR testing was developed as part of the NASA/Navy Abrupt Wing Stall Program, which was established for the purposes of understanding and preventing significant unexpected and uncommanded (thus, highly undesirable) lateral-directional motions associated with wing-drop/rock, which have been observed mostly in fighter airplanes under high-subsonic and transonic maneuvering conditions. Before FTR testing became available, wingrock/ drop behavior of high-performance airplanes undergoing development was not recognized until flight testing. FTR testing is a reliable means of detecting, and evaluating design modifications for reducing or preventing, very complex abrupt wing stall phenomena in a ground facility prior to flight testing. The FTR test rig was designed to replace an older sting attachment butt, such that a model with its force balance and support sting could freely rotate about the longitudinal axis. The rig (see figure) includes a rotary head supported in a stationary head with a forward spherical roller bearing and an aft needle bearing. Rotation is amplified by a set of gears and measured by a shaft-angle resolver; the roll angle can be resolved to within 0.067 degrees at a rotational speed up to 1,000 degrees/s. An assembly of electrically actuated brakes between the rotary and stationary heads can be used to hold the model against a rolling torque at a commanded roll angle. When static testing is required, a locking bar is used to fix the rotating head rigidly to the stationary head. Switching between the static and FTR test modes takes only about 30 minutes. The FTR test rig was originally mounted in a 16-ft (approximately 4.0-m) transonic wind tunnel, but could just as well be adapted to use in any large wind tunnel. In one series of tests on the FTR rig, static and dynamic characteristics of models of four different fighter airplanes were measured. Two of the models exhibited uncommanded lateral motions; the other two did not. A figure of merit was developed to discern the severity of lateral motions. Using this figure of merit, it was shown that the FTR test technique enabled identification of conditions under which the uncommanded lateral motions occurred. The wind-tunnel conditions thus identified were found to be correlated with flight conditions under which the corresponding full-size airplanes exhibited uncommanded lateral motions.

Experimental investigations on sodium-filled heat pipes

NASA Technical Reports Server (NTRS)

Dorner, S.; Reiss, F.; Schretzmann, K.

1977-01-01

The possibilities of producing heat pipes and, especially, the necessary capillary structures are discussed. Several types of heat pipes were made from stainless steel and tested at temperatures between 400 and 1055 deg C. The thermal power was determined by a calorimeter. Results indicate: bubble-free evaporation of sodium from rectangular open chennels is possible with a heat flux of more than 1,940 W/sq cm at 1055 C. The temperature drop along the tube could be measured only at low temperatures. A subdivided heat pipe worked against the gravitational field. A heat pipe with a capillary structure made of a rolled screen was supported by rings and bars operated at 250 W/sq cm heat flux in the evaporating region.

The Voyage of a Navigator An aspiring scholar's inside observations on the Affordable Care Act's rocky roll-out in North Carolina.

PubMed

Tripp, Hollie L

2015-01-01

North Carolina, a federally facilitated marketplace under the Affordable Care Act (ACA), stumbled in 2013 when opening its health-insurance exchange. Trouble was easy to foresee, as North Carolina had instituted a law barring any state agency from assisting enrollment in health-insurance plans made available through the ACA. Trained workers were needed to help citizens and legal immigrants "navigate" to these plans. Some of these "navigators" could be paid with federal funds, but many others had to work as volunteers. I was one of these volunteer navigators. Much went wrong in training, staffing, and operations, but much still was accomplished. Here I report observations, share assessments, and offer suggestions for similarly complex situations.

A Novel Virus Detected in Papillomas and Carcinomas of the Endangered Western Barred Bandicoot (Perameles bougainville) Exhibits Genomic Features of both the Papillomaviridae and Polyomaviridae▿

PubMed Central

Woolford, Lucy; Rector, Annabel; Van Ranst, Marc; Ducki, Andrea; Bennett, Mark D.; Nicholls, Philip K.; Warren, Kristin S.; Swan, Ralph A.; Wilcox, Graham E.; O'Hara, Amanda J.

2007-01-01

Conservation efforts to prevent the extinction of the endangered western barred bandicoot (Perameles bougainville) are currently hindered by a progressively debilitating cutaneous and mucocutaneous papillomatosis and carcinomatosis syndrome observed in captive and wild populations. In this study, we detected a novel virus, designated the bandicoot papillomatosis carcinomatosis virus type 1 (BPCV1), in lesional tissue from affected western barred bandicoots using multiply primed rolling-circle amplification and PCR with the cutaneotropic papillomavirus primer pairs FAP59/FAP64 and AR-L1F8/AR-L1R9. Sequencing of the BPCV1 genome revealed a novel prototype virus exhibiting genomic properties of both the Papillomaviridae and the Polyomaviridae. Papillomaviral properties included a large genome size (∼7.3 kb) and the presence of open reading frames (ORFs) encoding canonical L1 and L2 structural proteins. The genomic organization in which structural and nonstructural proteins were encoded on different strands of the double-stranded genome and the presence of ORFs encoding the nonstructural proteins large T and small t antigens were, on the other hand, typical polyomaviral features. BPCV1 may represent the first member of a novel virus family, descended from a common ancestor of the papillomaviruses and polyomaviruses recognized today. Alternatively, it may represent the product of ancient recombination between members of these two virus families. The discovery of this virus could have implications for the current taxonomic classification of Papillomaviridae and Polyomaviridae and can provide further insight into the evolution of these ancient virus families. PMID:17898069

Rolling Contact Fatigue Failure Mechanisms of Plasma-Nitrided Ductile Cast Iron

NASA Astrophysics Data System (ADS)

Wollmann, D.; Soares, G. P. P. P.; Grabarski, M. I.; Weigert, N. B.; Escobar, J. A.; Pintaude, G.; Neves, J. C. K.

2017-05-01

Rolling contact fatigue (RCF) of a nitrided ductile cast iron was investigated. Flat washers machined from a pearlitic ductile cast iron bar were quenched and tempered to maximum hardness, ground, polished and divided into four groups: (1) specimens tested as quenched and tempered; (2) specimens plasma-nitrided for 8 h at 400 °C; (3) specimens plasma-nitrided and submitted to a diffusion process for 16 h at 400 °C; and (4) specimens submitted to a second tempering for 24 h at 400 °C. Hardness profiles, phase analyses and residual stress measurements by x-ray diffraction, surface roughness and scanning electron microscopy were applied to characterize the surfaces at each step of this work. Ball-on-flat washer tests were conducted with a maximum contact pressure of 3.6 GPa, under flood lubrication with a SAE 90 API GL-5 oil at 50 °C. Test ending criterion was the occurrence of a spalling. Weibull analysis was used to characterize RCF's lifetime data. Plasma-nitrided specimens exhibited a shorter RCF lifetime than those just quenched and tempered. The effects of nitriding on the mechanical properties and microstructure of the ductile cast iron are discussed in order to explain the shorter endurance of nitrided samples.

Effects of thermomechanical processing on tensile and long-time creep behavior of Nb-1 percent Zr-0.1 percent C sheet

NASA Technical Reports Server (NTRS)

Titran, Robert H.; Uz, Mehmet

1994-01-01

Effects of thermomechanical processing on the mechanical properties of Nb-1 wt. percent Zr-0.1 wt. percent C, a candidate alloy for use in advanced space power systems, were investigated. Sheet bars were cold rolled into 1-mm thick sheets following single, double, or triple extrusion operations at 1900 K. All the creep and tensile specimens were given a two-step heat treatment 1 hr at 1755 K + 2 hr 1475 K prior to testing. Tensile properties were determined at 300 as well as at 1350 K. Microhardness measurements were made on cold rolled, heat treated, and crept samples. Creep tests were carried out at 1350 K and 34.5 MPa for times of about 10,000 to 19,000 hr. The results show that the number of extrusions had some effects on both the microhardness and tensile properties. However, the long-time creep behavior of the samples were comparable, and all were found to have adequate properties to meet the design requirements of advanced power systems regardless of thermomechanical history. The results are discussed in correlation with processing and microstructure, and further compared to the results obtained from the testing of Nb-1 wt. percent Zr and Nb-1 wt. percent Zr-0.06 wt. percent C alloys.

Multiphysics modelling of multibody systems: application to car semi-active suspensions

NASA Astrophysics Data System (ADS)

Docquier, N.; Poncelet, A.; Delannoy, M.; Fisette, P.

2010-12-01

The goal of the present article is to analyse the performances of a modern vehicle equipped with a novel suspension system linking front, rear, right and left cylinders via a semi-active hydraulic circuit, developed by the Tenneco Automotive company. In addition to improving the vehicle's vertical performances (in terms of comfort), both the stiff roll motion of the carbody and the soft wrap motion of the rear/front wheel-axle units can be obtained and tuned via eight electrovalves. The proposed system avoids the use of classical anti-roll bars, which would be incompatible with the wrap performance. A major problem of the project is to produce a realistic and efficient 3D multibody dynamic model of an Audi A6 coupled, at the equational level, with an hydraulic model of the suspension including cylinders, accumulators, valve characteristics, oil compressibility and pipe dynamics. As regards the hydraulic submodel, a particular attention is paid to assemble resistive components properly without resorting to the use of artificial volumes, as proposed by some software dealing with the dynamics of hydraulic systems. According to Tenneco Automotive requirements, this model must be produced in a Matlab/Simulink form, in particular for control purposes. Thanks to the symbolic approach underlying our multibody program; a unified hybrid model can be obtained as a unique plant dynamic block to be real-time integrated in the Simulink environment on a standard computer. Simulation results highlight the advantages of this new suspension system, in particular regarding the behaviour of the car which can remain stiff in roll for curve negotiation, while maintaining a soft wrap behaviour on uneven surfaces.

The effect of the equatorially symmetric zonal winds of Saturn on its gravitational field

NASA Astrophysics Data System (ADS)

Kong, Dali; Zhang, Keke; Schubert, Gerald; Anderson, John D.

2018-04-01

The penetration depth of Saturn’s cloud-level winds into its interior is unknown. A possible way of estimating the depth is through measurement of the effect of the winds on the planet’s gravitational field. We use a self-consistent perturbation approach to study how the equatorially symmetric zonal winds of Saturn contribute to its gravitational field. An important advantage of this approach is that the variation of its gravitational field solely caused by the winds can be isolated and identified because the leading-order problem accounts exactly for rotational distortion, thereby determining the irregular shape and internal structure of the hydrostatic Saturn. We assume that (i) the zonal winds are maintained by thermal convection in the form of non-axisymmetric columnar rolls and (ii) the internal structure of the winds, because of the Taylor-Proundman theorem, can be uniquely determined by the observed cloud-level winds. We calculate both the variation ΔJn , n = 2, 4, 6 … of the axisymmetric gravitational coefficients Jn caused by the zonal winds and the non-axisymmetric gravitational coefficients ΔJnm produced by the columnar rolls, where m is the azimuthal wavenumber of the rolls. We consider three different cases characterized by the penetration depth 0.36, R S, 0.2, R S and 0.1, R S, where R S is the equatorial radius of Saturn at the 1-bar pressure level. We find that the high-degree gravitational coefficient (J 12 + ΔJ 12) is dominated, in all the three cases, by the effect of the zonal flow with |ΔJ 12/J 12| > 100% and that the size of the non-axisymmetric coefficients ΔJ mn directly reflects the depth and scale of the flow taking place in the Saturnian interior.

Simultaneous multiscale measurements on dynamic deformation of a magnesium alloy with synchrotron x-ray imaging and diffraction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lu, L.; Sun, T.; Fezzaa, K.

Dynamic split Hopkinson pressure bar experiments with in situ synchrotron x-ray imaging and diffraction are conducted on a rolled magnesium alloy at high strain rates of ~5500 s-1. High speed multiscale measurements including stress–strain curves (macroscale), strain fields (mesoscale), and diffraction patterns (microscale) are obtained simultaneously, revealing strong anisotropy in deformation across different length scales. {1012} extension twinning induces homogenized strain fields and gives rise to rapid increase in strain hardening rate, while dislocation motion leads to inhomogeneous deformation and a decrease in strain hardening rate. During the early stage of plastic deformation, twinning is dominant in dynamic compression, whilemore » dislocation motion prevails in quasi-static loading, manifesting a strain-rate dependence of deformation.« less

Processing of oats and the impact of processing operations on nutrition and health benefits.

PubMed

Decker, Eric A; Rose, Devin J; Stewart, Derek

2014-10-01

Oats are a uniquely nutritious food as they contain an excellent lipid profile and high amounts of soluble fibre. However, an oat kernel is largely non-digestible and thus must be utilised in milled form to reap its nutritional benefits. Milling is made up of numerous steps, the most important being dehulling to expose the digestible groat, heat processing to inactivate enzymes that cause rancidity, and cutting, rolling or grinding to convert the groat into a product that can be used directly in oatmeal or can be used as a food ingredient in products such as bread, ready-to-eat breakfast cereals and snack bars. Oats can also be processed into oat bran and fibre to obtain high-fibre-containing fractions that can be used in a variety of food products.

Dynamic Fracture Initiation Toughness at Elevated Temperatures With Application to the New Generation of Titanium Aluminide Alloys. Chapter 8

NASA Technical Reports Server (NTRS)

Shazly, Mostafa; Prakash, Vikas; Draper, Susan; Shukla, Arun (Editor)

2006-01-01

Recently, a new generation of titanium aluminide alloy, named Gamma-Met PX, has been developed with better rolling and post-rolling characteristics. I'revious work on this alloy has shown the material to have higher strengths at room and elevated temperatures when compared with other gamma titanium aluminides. In particular, this new alloy has shown increased ductility at elevated temperatures under both quasi-static and high strain rate uniaxial compressive loading. However, its high strain rate tensile ductility at room and elevated temperatures is limited to approx. 1%. In the present chapter, results of a study to investigate the effects of loading rate and test temperature on the dynamic fracture initiation toughness in Gamma-Met PX are presented. Modified split Hopkinson pressure bar was used along with high-speed photography to determine the crack initiation time. Three-point bend dynamic fracture experiments were conducted at impact speeds of approx. 1 m/s and tests temperatures of up-to 1200 C. The results show that thc dynamic fracture initiation toughness decreases with increasing test temperatures beyond 600 C. Furthermore, thc effect of long time high temperature air exposure on the fracture toughness was investigated. The dynamic fracture initiation toughness was found to decrease with increasing exposure time. The reasons behind this drop are analyzed and discussed.

Grain size dependence of dynamic mechanical behavior of AZ31B magnesium alloy sheet under compressive shock loading

DOE Office of Scientific and Technical Information (OSTI.GOV)

Asgari, H., E-mail: hamed.asgari@usask.ca; Odeshi, A.G.; Szpunar, J.A.

2015-08-15

The effects of grain size on the dynamic deformation behavior of rolled AZ31B alloy at high strain rates were investigated. Rolled AZ31B alloy samples with grain sizes of 6, 18 and 37 μm, were subjected to shock loading tests using Split Hopkinson Pressure Bar at room temperature and at a strain rate of 1100 s{sup −} {sup 1}. It was found that a double-peak basal texture formed in the shock loaded samples. The strength and ductility of the alloy under the high strain-rate compressive loading increased with decreasing grain size. However, twinning fraction and strain hardening rate were found tomore » decrease with decreasing grain size. In addition, orientation imaging microscopy showed a higher contribution of double and contraction twins in the deformation process of the coarse-grained samples. Using transmission electron microscopy, pyramidal dislocations were detected in the shock loaded sample, proving the activation of pyramidal slip system under dynamic impact loading. - Highlights: • A double-peak basal texture developed in all shock loaded samples. • Both strength and ductility increased with decreasing grain size. • Twinning fraction and strain hardening rate decreased with decreasing grain size. • ‘g.b’ analysis confirmed the presence of dislocations in shock loaded alloy.« less

Effects of processing and prolonged high temperature exposure on the microstructure of Nb-1Zr-C sheet

NASA Technical Reports Server (NTRS)

Uz, Mehmet; Titran, R. H.

1993-01-01

High temperature stability of the microstructure of Nb-1Zr sheet containing 0.1 and 0.06 wt. percent C was studied as affected by processing and prolonged 1350 K exposure with and without applied stress. Sheets were fabricated by cold rolling bars that were single-, double-, or triple-extruded at 1900 K. Creep samples were double-annealed (1 h at 1755 K + 2 h at 1475 K) prior to testing at 1350 K and 10,000 - 34,500 h. The microstructures of the as-cast, extruded, rolled, DA, and crept samples were characterized using various metallographic and analytical methods. The precipitates were rather coarse Nb2C initially, but transformed to finer (less than or equal to 1 micron) carbides of (Zr, Nb)C with each subsequent high temperature process. The grain size, and the relative amount and morphology of (Zr, Nb)C were found to be affected by the number of extrusions and to some extent by C-content. However, the microstructures of all the crept samples were similar with (Zr, Nb)C distributed throughout the matrix indicating that prolonged exposure to 1350 K gave rise to complete transformation of Nb2C to (Zr, Nb)C regardless of the processing history. These and other observations are presented with the emphasis on the correlation between processing, microstructure, and creep properties.

Distributed Offline Data Reconstruction in BaBar

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pulliam, Teela M

The BaBar experiment at SLAC is in its fourth year of running. The data processing system has been continuously evolving to meet the challenges of higher luminosity running and the increasing bulk of data to re-process each year. To meet these goals a two-pass processing architecture has been adopted, where 'rolling calibrations' are quickly calculated on a small fraction of the events in the first pass and the bulk data reconstruction done in the second. This allows for quick detector feedback in the first pass and allows for the parallelization of the second pass over two or more separate farms.more » This two-pass system allows also for distribution of processing farms off-site. The first such site has been setup at INFN Padova. The challenges met here were many. The software was ported to a full Linux-based, commodity hardware system. The raw dataset, 90 TB, was imported from SLAC utilizing a 155 Mbps network link. A system for quality control and export of the processed data back to SLAC was developed. Between SLAC and Padova we are currently running three pass-one farms, with 32 CPUs each, and nine pass-two farms with 64 to 80 CPUs each. The pass-two farms can process between 2 and 4 million events per day. Details about the implementation and performance of the system will be presented.« less

Low cost fabrication development for oxide dispersion strengthened alloy vanes

NASA Technical Reports Server (NTRS)

Perkins, R. J.; Bailey, P. G.

1978-01-01

Viable processes were developed for secondary working of oxide dispersion strengthened (ODS) alloys to near-net shapes (NNS) for aircraft turbine vanes. These processes were shown capable of producing required microstructure and properties for vane applications. Material cost savings of 40 to 50% are projected for the NNS process over the current procedures which involve machining from rectangular bar. Additional machining cost savings are projected. Of three secondary working processes evaluated, directional forging and plate bending were determined to be viable NNS processes for ODS vanes. Directional forging was deemed most applicable to high pressure turbine (HPT) vanes with their large thickness variations while plate bending was determined to be most cost effective for low pressure turbine (LPT) vanes because of their limited thickness variations. Since the F101 LPT vane was selected for study in this program, development of plate bending was carried through to establishment of a preliminary process. Preparation of ODS alloy plate for bending was found to be a straight forward process using currently available bar stock, providing that the capability for reheating between roll passes is available. Advanced ODS-NiCrAl and ODS-FeCrAl alloys were utilized on this program. Workability of all alloys was adequate for directional forging and plate bending, but only the ODS-FeCrAl had adequate workability for shaped preform extrustion.

Investigation Of The Influence Of Temperature Inversions And Turbulence On Land-Atmosphere Interactions For Rolling Terrain

NASA Astrophysics Data System (ADS)

Osibanjo, Olabosipo O.

The objectives of this work are to calculate surface fluxes for rolling terrain using observational data collected during one week in September 2014 from a monitoring site in Echo, Oregon and to investigate the log law in the ABL. The site is located in the Columbia Basin with rolling terrain, irrigated farmland, and over 100 wind turbines. The 10 m tower was placed in a small valley depression to isolate nighttime temperature inversions. This thesis presents observations of momentum, sensible heat, moisture, and CO2 fluxes from data collected at a sampling frequency of 10Hz at four heights. Results show a strong correlation between temperature inversions and CO 2 flux. The log layer could not be achieved as the value of the estimated von Karman constant (˜0.62) is not close to that of the accepted value of 0.41. The impact of the irrigated farmland near the measurement site was observed in the latent heat flux, where the advection of moisture was evident in the tower moisture gradient. A strong relationship was also observed between fluxes of sensible heat, latent heat, CO2, and atmospheric stability. The average nighttime CO2 concentration observed was ˜407 ppm, and daytime ˜388 ppm compared to the 2013 global average CO2 concentration of 395 ppm. The maximum CO2 concentration (˜485 ppm) was observed on the strongest temperature inversion night. There are few uncertainties in the measurements. The manufacturer for the eddy covariance instruments (EC 150) quotes uncertainty of +/- 0.1°C for temperature between -0°C-40°C. Error bars were generated on the estimated surface sensible heat flux using the standard deviation and mean values. Under the most stable atmospheric conditions, uncertainty (assumed to be the variability in the flux estimates) was close to the minimum (˜+/- 5 W m-2). (Abstract shortened by ProQuest.).

Epoxy coated reinforcement in bridge decks

NASA Astrophysics Data System (ADS)

Wills, J.

A review was conducted of methods relating to the use of epoxy coated reinforcing bars for bridge decks and their potential for use in the United Kingdom. A survey of work carried out in the USA was carried out and the analysis used in a preliminary cost study. The options of having either a hot rolled asphalt surfacing or a permanently exposed concrete wearing surface were considered. It was concluded that epoxy coating of the top steel in addition to current waterproofing practice would provide, at relatively little extra cost, additional assurance that the reinforcement would be adequately protected throughout the life of a bridge. Current design rules do not permit decks with permanently exposed concrete wearing surface without waterproofing. Epoxy coating may afford a means of introducing such decks but before a positive recommendation to delete waterproofing can be made further studies would have to be undertaken.

Development study of compositions for advanced wrought nickel-base superalloys

NASA Technical Reports Server (NTRS)

Kent, W. B.

1972-01-01

Using NASA IIb as a base composition, the effects of five key elements (carbon, tungsten, tantalum, aluminum, and hafnium) on resultant properties were investigated in an effort to optimize the composition and derive new wrought high temperature alloys with improved strength characteristics. A total of nineteen compositions were melted, extruded, and rolled to bar stock using thermomechanical processing. Both full and partial solution heat treatments were developed for the compositions. Tensile properties from room temperature to 1800 deg F, stress and creep rupture properties to 1800 deg F, and thermal stability characteristics were evaluated. NASA IIb-7 exhibited the best response to the partial solution heat treatment for optimum properties up to 1200 deg F. The alloy contained 0.13C, 9.0 Cr, 9.0 Co, 2.0 Mo, 7.5 W, 10.0 Ta, 3.5 Al, 0.75 Ti, 0.02 B, 0.10 Zr, 0.50 V, 1.0 Hf, and balance nickel.

Development of dispersion strengthened nickel-chromium alloy (Ni-Cr-ThO2) sheet for space shuttle vehicles, part 2

NASA Technical Reports Server (NTRS)

Klingler, L. J.; Weinberger, W. R.; Bailey, P. G.; Baranow, S.

1972-01-01

Two dispersion strengthened nickel base alloy systems were developed for use at temperatures up to 1204 C(2200 F); TD nickel chromium (TDNiCr) and TD nickel chromium aluminum (TDNiCrA1). They are considered candidate materials for use on the thermal protection systems of the space shuttle and for long term use in aircraft gas turbine engine applications. Improved manufacturing processes were developed for the fabrication of TDNiCr sheet and foil to specifications. Sheet rolling process studies and extrusion studies were made on two aluminum containing alloys: Ni-16%Cr-3.5%A1-2%ThO2 and Ni-16%Cr-5.0%A12%ThO2. Over 1600 kg.(3500 lb.) of plate, sheet, foil, bar and extrusion products were supplied to NASA Centers for technology studies.

Genetic and grade and tonnage models for sandstone-hosted roll-type uranium deposits, Texas Coastal Plain, USA

USGS Publications Warehouse

Hall, Susan M.; Mihalasky, Mark J.; Tureck, Kathleen; Hammarstrom, Jane M.; Hannon, Mark

2017-01-01

The coincidence of a number of geologic and climatic factors combined to create conditions favorable for the development of mineable concentrations of uranium hosted by Eocene through Pliocene sandstones in the Texas Coastal Plain. Here 254 uranium occurrences, including 169 deposits, 73 prospects, 6 showings and 4 anomalies, have been identified. About 80 million pounds of U3O8 have been produced and about 60 million pounds of identified producible U3O8 remain in place. The development of economic roll-type uranium deposits requires a source, large-scale transport of uranium in groundwater, and deposition in reducing zones within a sedimentary sequence. The weight of the evidence supports a source from thick sequences of volcanic ash and volcaniclastic sediment derived mostly from the Trans-Pecos volcanic field and Sierra Madre Occidental that lie west of the region. The thickest accumulations of source material were deposited and preserved south and west of the San Marcos arch in the Catahoula Formation. By the early Oligocene, a formerly uniformly subtropical climate along the Gulf Coast transitioned to a zoned climate in which the southwestern portion of Texas Coastal Plain was dry, and the eastern portion humid. The more arid climate in the southwestern area supported weathering of volcanic ash source rocks during pedogenesis and early diagenesis, concentration of uranium in groundwater and movement through host sediments. During the middle Tertiary Era, abundant clastic sediments were deposited in thick sequences by bed-load dominated fluvial systems in long-lived channel complexes that provided transmissive conduits favoring transport of uranium-rich groundwater. Groundwater transported uranium through permeable sandstones that were hydrologically connected with source rocks, commonly across formation boundaries driven by isostatic loading and eustatic sea level changes. Uranium roll fronts formed as a result of the interaction of uranium-rich groundwater with either (1) organic-rich debris adjacent to large long-lived fluvial channels and barrier–bar sequences or (2) extrinsic reductants entrained in formation water or discrete gas that migrated into host units via faults and along the flanks of salt domes and shale diapirs. The southwestern portion of the region, the Rio Grande embayment, contains all the necessary factors required for roll-type uranium deposits. However, the eastern portion of the region, the Houston embayment, is challenged by a humid environment and a lack of source rock and transmissive units, which may combine to preclude the deposition of economic deposits. A grade and tonnage model for the Texas Coastal Plain shows that the Texas deposits represent a lower tonnage subset of roll-type deposits that occur around the world, and required aggregation of production centers into deposits based on geologic interpretation for the purpose of conducting a quantitative mineral resource assessment.

Reconstruction of primordial tensor power spectra from B -mode polarization of the cosmic microwave background

NASA Astrophysics Data System (ADS)

Hiramatsu, Takashi; Komatsu, Eiichiro; Hazumi, Masashi; Sasaki, Misao

2018-06-01

Given observations of the B -mode polarization power spectrum of the cosmic microwave background (CMB), we can reconstruct power spectra of primordial tensor modes from the early Universe without assuming their functional form such as a power-law spectrum. The shape of the reconstructed spectra can then be used to probe the origin of tensor modes in a model-independent manner. We use the Fisher matrix to calculate the covariance matrix of tensor power spectra reconstructed in bins. We find that the power spectra are best reconstructed at wave numbers in the vicinity of k ≈6 ×10-4 and 5 ×10-3 Mpc-1 , which correspond to the "reionization bump" at ℓ≲6 and "recombination bump" at ℓ≈80 of the CMB B -mode power spectrum, respectively. The error bar between these two wave numbers is larger because of the lack of the signal between the reionization and recombination bumps. The error bars increase sharply toward smaller (larger) wave numbers because of the cosmic variance (CMB lensing and instrumental noise). To demonstrate the utility of the reconstructed power spectra, we investigate whether we can distinguish between various sources of tensor modes including those from the vacuum metric fluctuation and SU(2) gauge fields during single-field slow-roll inflation, open inflation, and massive gravity inflation. The results depend on the model parameters, but we find that future CMB experiments are sensitive to differences in these models. We make our calculation tool available online.

Evaluation of the Susceptibility to SCC Initiation of Alloy 690 in Simulated PWR Primary Water

NASA Astrophysics Data System (ADS)

Tsutsumi, Kazuya; Couvant, Thierry

Alloy 690 has been widely used in fabricating components of LWR plants as an alternative material to Alloy 600 which has exhibited a significant susceptibility to PWSCC. However, some authors have reported that Alloy 690 can suffer a significant susceptibility to SCC crack growth when highly cold worked. While most of the recent studies emphasize SCC propagation phase, EDF and its partners are focusing on the material's resistance to SCC initiation. This paper summarizes the current work carried out at EDF MAI on the SCC initiation. By means of constant elongation rate tests (CERTs) and constant displacement tests, experimental investigation of the susceptibility to PWSCC were performed. No SCC was observed on either an extruded bar or on two plates, even after 24%-1D cold rolling, confirming the superior PWSCC resistance of Alloy 690 independent of a amount of intergranular precipitation of carbides, and also revealing that such cold rolling does not necessarily decrease the resistance to SCC. On the other hand, a experimental steam generator tube that has a degraded microstructure due to specific heat-treatment revealed its susceptibility to SCC, probably because of the interactive effect of microstructure with heavy intragranular carbide precipitations and the cold worked superficial layer. This phenomenon is in good agreement with results previously published. In this study, the maximal crack depth slightly increased when DH increased from 5 to 60 cc.kg-1H2O. No significant prior ageing effect on the crack depth was observed, even when ageing was combined with high DH.

Prediction Of The Fracture Due To Mannesmann Effect In Tube Piercing

NASA Astrophysics Data System (ADS)

Fanini, S.; Ghiotti, A.; Bruschi, S.

2007-05-01

Mannesmann piercing process is a well-known hot rolling process used for seamless tube production. Its special feature is the so-called Mannesmann effect, that is the cavity formation in the center of the cylindrical billet and its propagation along the axis due to stress state caused by the rolls in the early stages of the process. The cavity is then expanded and sized in its internal diameter by an incoming plug. The industrial requirement is to know quite precisely the characteristics of the cavity especially in terms of its location along the billet axis in order to minimize the plug wear and the oxidation of the pierced bar. However, the scientific knowledge about the fracture mechanism leading to the Mannesmann effect is still limited, even if several theories have been proposed; this lack makes the design and optimization of the process through numerical simulations still a challenging task. The aim of this work is then to develop a suitably calibrated FE model of the piercing process in its first stage before the plug arrival, in order to investigate the Mannesmann effect using different damage criteria. Hot tensile tests, capable to reproduce the industrial conditions in terms of temperature, strain rate, and stress states, are carried out to investigate the material workability and to determine the parameters of the damage models on specimens machined from continuous-casting steel billets. The calculated parameters are implemented in the numerical model of the process and a sensitivity analysis to the different criteria is carried out, comparing numerical results with non-plug piercing tests conducted in the industrial plant.

Cross-directional interlocking of rolls in an air press of a papermaking machine

DOEpatents

Beck, David A.; Gorshe, Thomas

2003-05-13

An air press for pressing a paper web is composed of a plurality of rolls including at least a first roll and a second roll. The first roll and the second roll are positioned adjacent one another and form a first nip therebetween. Further, the first roll and the second roll each have a roll end, the roll end of the first roll adjoining the roll end of the second roll. A bevel plate is attached to the roll end of the first roll, the bevel plate having at least a first angled plate face. A seal ring is positioned adjacent the roll end of the second roll, the seal ring being juxtaposed to the bevel plate. The seal ring has at least a first angled ring face, and the first angled ring face mates with the first angled plate face.

The Effect of Impurities on the Processing of Aluminum Alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zi-Kui Liu; Shengjun Zhang; Qingyou Han

2007-04-23

For this Aluminum Industry of the Future (IOF) project, the effect of impurities on the processing of aluminum alloys was systematically investigated. The work was carried out as a collaborative effort between the Pennsylvania State University and Oak Ridge National Laboratory. Industrial support was provided by ALCOA and ThermoCalc, Inc. The achievements described below were made. A method that combines first-principles calculation and calculation of phase diagrams (CALPHAD) was used to develop the multicomponent database Al-Ca-K-Li-Mg-Na. This method was extensively used in this project for the development of a thermodynamic database. The first-principles approach provided some thermodynamic property data thatmore » are not available in the open literature. These calculated results were used in the thermodynamic modeling as experimental data. Some of the thermodynamic property data are difficult, if not impossible, to measure. The method developed and used in this project allows the estimation of these data for thermodynamic database development. The multicomponent database Al-Ca-K-Li-Mg-Na was developed. Elements such as Ca, Li, Na, and K are impurities that strongly affect the formability and corrosion behavior of aluminum alloys. However, these impurity elements are not included in the commercial aluminum alloy database. The process of thermodynamic modeling began from Al-Na, Ca-Li, Li-Na, K-Na, and Li-K sub-binary systems. Then ternary and higher systems were extrapolated because of the lack of experimental information. Databases for five binary alloy systems and two ternary systems were developed. Along with other existing binary and ternary databases, the full database of the multicomponent Al-Ca-K-Li-Mg-Na system was completed in this project. The methodology in integrating with commercial or other aluminum alloy databases can be developed. The mechanism of sodium-induced high-temperature embrittlement (HTE) of Al-Mg is now understood. Using the thermodynamic database developed in this project, thermodynamic simulations were carried out to investigate the effect of sodium on the HTE of Al-Mg alloys. The simulation results indicated that the liquid miscibility gap resulting from the dissolved sodium in the molten material plays an important role in HTE. A liquid phase forms from the solid face-centered cubic (fcc) phase (most likely at grain boundaries) during cooling, resulting in the occurrence of HTE. Comparison of the thermodynamic simulation results with experimental measurements on the high-temperature ductility of an Al-5Mg-Na alloy shows that HTE occurs in the temperature range at which the liquid phase exists. Based on this fundamental understanding of the HTE mechanism during processing of aluminum alloy, an HTE sensitive zone and a hot-rolling safe zone of the Al-Mg-Na alloys are defined as functions of processing temperature and alloy composition. The tendency of HTE was evaluated based on thermodynamic simulations of the fraction of the intergranular sodium-rich liquid phase. Methods of avoiding HTE during rolling/extrusion of Al-Mg-based alloys were suggested. Energy and environmental benefits from the results of this project could occur through a number of avenues: (1) energy benefits accruing from reduced rejection rates of the aluminum sheet and bar, (2) reduced dross formation during the remelting of the aluminum rejects, and (3) reduced CO2 emission related to the energy savings. The sheet and extruded bar quantities produced in the United States during 2000 were 10,822 and 4,546 million pounds, respectively. It is assumed that 50% of the sheet and 10% of the bar will be affected by implementing the results of this project. With the current process, the rejection rate of sheet and bar is estimated at 5%. Assuming that at least half of the 5% rejection of sheet and bar will be eliminated by using the results of this project and that 4% of the aluminum will be lost through dross (Al2O3) during remelting of the rejects, the full-scale industrial implementation of the project results would lead to energy savings in excess of 6.2 trillion Btu/year and cost savings of $42.7 million by 2020.« less

Controlled-force end seal arrangement for an air press of a papermaking machine

DOEpatents

Beck, David A.

2003-07-08

An air press for pressing a fiber web includes a plurality of rolls and a pair of end seal arrangements. Of the plurality of rolls, each pair of adjacent rolls forms a nip therebetween. Further, each roll has a pair of roll ends, the plurality of rolls together forming two sets of roll ends. Each end seal arrangement coacts with one set of roll ends, the plurality of rolls and the pair of end seal arrangements together defining an air press chamber having an air chamber pressure. Each end seal arrangement is composed of at least one roll seal, including a first roll seal, and an adjustable bias mechanism. Each roll seal forms a seal with at least one roll end, and one side of the first roll seal being exposed to the air chamber pressure. The adjustable bias mechanism is configured for controlling a position of each roll seal relative to a respective at least one roll end and for adjusting a seal force between the roll seal and the respective at least one roll end.

Static Design and Finite Element Analysis of Innovative CFRP Transverse Leaf Spring

NASA Astrophysics Data System (ADS)

Carello, M.; Airale, A. G.; Ferraris, A.; Messana, A.; Sisca, L.

2017-12-01

This paper describes the design and the numerical modelization of a novel transverse Carbon Fiber Reinforced Plastic (CFRP) leaf-spring prototype for a multilink suspension. The most significant innovation is in the functional integration where the leaf spring has been designed to work as spring, anti-roll bar, lower and longitudinal arms at the same time. In particular, the adopted work flow maintains a very close correlation between virtual simulations and experimental tests. Firstly, several tests have been conducted on the CFRP specimen to characterize the material property. Secondly, a virtual card fitting has been carried out in order to set up the leaf-spring Finite Element (FE) model using CRASURV formulation as material law and RADIOSS as solver. Finally, extensive tests have been done on the manufactured component for validation. The results obtained show a good agreement between virtual simulation and experimental tests. Moreover, this solution enabled the suspension to reduce about 75% of the total mass without losing performance.

Improvement of rolling 6 mm thin plates in plate rolling mill PT. Krakatau Posco

NASA Astrophysics Data System (ADS)

Pujiyanto, Hamdani

2017-01-01

A 6-mm thin plate is difficult to produce especially if the product requires wide size and high strength. Flatness is the main quality issue in rolling 6-mm plate using a 4-high reversing mill which use ±1100-mm work roll. Thus some methods are applied to overcome such issue in order to comply to customer quality requirement. Pre-rolling, rolling, and post-rolling conditions have to be considered comprehensively. Roll unit management will be the key factor before rolling condition. The roll unit itself has a significant impact on work roll crown wearness in relation with work roll intial crown and thermal crown. Work roll crown along with the modification of hydraulic gap control (HGC) could directly alter the flatness of the plate.

A Roll, Fin, and Fin Controller Prediction Computer Program.

DTIC Science & Technology

1980-06-01

IERATI *EQ. 03 WRITE16920301 ROLL 365 365 3R1TE(G. 26311 ROLL 366 no 505 ImU - 1,NNU ROLL 36? 50S WRITE(G.2011 3U(I’U),OAWPU(1PU,SIGLCfINU) ROLL 360...ROLL DAMPING WILL BE ONE**/$ ROLL 642 2016 FORMAT (/jIX,*LONGCRESTEO SVECTRA AND COMPONENTS WILL SE PRINTED. ROLL 44S 2’) ROLL 444 2019 FORMAT (1/19

CONTROL FOR ROLLING MILL

DOEpatents

Shuck, A.B.; Shaw, W.C.

1961-06-20

A plutonium-rolling apparatus is patented that has two sets of feed rolls, shaping rolls between the feed rolls, and grippers beyond the feed rolls, which ready a workpiece for a new pass through the shaping rolls by angularly shifting the workpiece about its axis or transversely moving it on a line parallel to the axes of the shaping rolls. Actuation of each gripper for gripping or releasing the workpiece is produced by the relative positions assumed by the feed rolls adjacent to the gripper as the workpiece enters or leaves the feed rolls.

An experimental study for determining human discomfort response to roll vibration

NASA Technical Reports Server (NTRS)

Leatherwood, J. D.; Dempsey, T. K.; Clevenson, S. A.

1976-01-01

An experimental study using a passenger ride quality apparatus (PRQA) was conducted to determine the subjective reactions of passengers to roll vibrations. The data obtained illustrate the effect upon human comfort of several roll-vibration parameters: namely, roll acceleration level, roll frequency, and seat location (i.e., distance from axis of rotation). Results of an analysis of variance indicated that seat location had no effect on discomfort ratings of roll vibrations. The effect of roll acceleration level was significant, and discomfort ratings increased markedly with increasing roll acceleration level at all roll frequencies investigated. Of particular interest, is the fact that the relationship between discomfort ratings and roll acceleration level was linear in nature. The effect of roll frequency also was significant as was the interaction between roll acceleration level and roll frequency.

Experimental and Theoretical Study on Minimum Achievable Foil Thickness during Asymmetric Rolling

PubMed Central

Tang, Delin; Liu, Xianghua; Song, Meng; Yu, Hailiang

2014-01-01

Parts produced by microforming are becoming ever smaller. Similarly, the foils required in micro-machines are becoming ever thinner. The asymmetric rolling technique is capable of producing foils that are thinner than those produced by the conventional rolling technique. The difference between asymmetric rolling and conventional rolling is the ‘cross-shear’ zone. However, the influence of the cross-shear zone on the minimum achievable foil thickness during asymmetric rolling is still uncertain. In this paper, we report experiments designed to understand this critical influencing factor on the minimum achievable thickness in asymmetric rolling. Results showed that the minimum achievable thickness of rolled foils produced by asymmetric rolling with a rolling speed ratio of 1.3 can be reduced to about 30% of that possible by conventional rolling technique. Furthermore, the minimum achievable thickness during asymmetric rolling could be correlated to the cross-shear ratio, which, in turn, could be related to the rolling speed ratio. From the experimental results, a formula to calculate the minimum achievable thickness was established, considering the parameters cross-shear ratio, friction coefficient, work roll radius, etc. in asymmetric rolling. PMID:25203265

Generation, transport and preservation of armoured mudballs in an ephemeral gully system

NASA Astrophysics Data System (ADS)

Mather, Anne; Stokes, Martin; Pirrie, Duncan; Hartley, Richard

2008-08-01

Armoured mudballs have been reported from modern fluvial catchments and preserved in ancient (Quaternary and older) sedimentary sequences. Despite many descriptions of mudballs in the literature there is little systematic analysis of their physical properties, genesis, transport and deposition within alluvial sequences. This study uses two adjacent catchments developed on identical geology in southeast Spain that offer a unique opportunity to examine the key controls on armoured mudball development as one catchment produces armoured mudball whilst the second does not. Field survey using a Total Station together with laboratory tests for material composition and aggregate stability were used to examine the catchment and the armoured mudballs. The results show that the generation of the armoured mudballs is heavily dependent on the correct sediment supply (suitable aggregates to act as mudball 'seeds', and suitable fragments to source the armour) and good slope-channel coupling within the catchment. Coupling is facilitated by steep gully sides which deliver the weathered blocks of marl (mudball 'seeds') to the gully floor. The 'seeds' form the core of the mudballs in the 'mudball factory' zone. If the 'seeds' are subjected to sealing by moisture from rainfall the mudball will hold together through negative pore pressures and can be transported by the ensuing gully flow. As the mudball rolls it picks up a surface armour which becomes embedded into the mudball. With longer transport paths the turbulent nature of the flow creates spherical mudballs which are size sorted downstream by the hydraulics of the flow rather than attrition. Armoured mudball deposition occurs within unit braid bars in areas of waning flow (due to transmission losses), within vegetated, point or mid-channel bars. The armoured mudballs are preferentially deposited within the coarser bar head of these depositional units, with smaller marl fragments forming the finer bar tail. Trenching of the bars reveals that the armoured mudballs are preserved in the subsurface although they may become increasingly flattened upon burial at depth, and may be difficult to recognise due to disaggregation by roots. This study suggests that armoured mudballs recognised in ancient alluvial sequences imply seasonality of climate and good slope-channel coupling within the catchment area, and that they are capable of transporting delicate flora undamaged, making them good targets for pollen recovery in ancient alluvial sequences. Where armoured mudballs were present but go unrecognised in the ancient record the mode and energy of transportation and deposition of the fine sediment may be misinterpreted as the fines are in fact being transported as bedload rather than suspended load. The armoured mudballs have also been noted to transport pristine microfauna such as ostracod shells from the source area material. This may provide challenges to palaeoenvironmental interpretations of the mud-dominated unit as environmentally significant fauna may not be contemporaneous with the unit.

Microstructural and mechanical responses to various rolling speeds determined in multi-pass break-down rolling of AZ31B alloy

NASA Astrophysics Data System (ADS)

Jia, Weitao; Tang, Yan; Ning, Fangkun; Le, Qichi; Cui, Jianzhong

2018-04-01

Different rolling operations of as-cast AZ31B alloy were performed under different rolling speed (18 ∼ 72 m min‑1) and rolling pass conditions at 400 °C. Microstructural studies, tensile testing and formability evaluation relevant to each rolling operation were investigated. For 1-pass rolling, coarse average grain size (CAGS) region gradually approached the center layer as the rolling speed increased. Moreover, twins, shear bands and coarse-grain structures were the dominant components in the microstructure of plates rolled at 18, 48 and 72 m min‑1, respectively, indicating the severe deformation inhomogeneity under the high reduction per pass condition. For 2-pass rolling and 4-pass rolling, dynamic recrystallization was observed to be well and CAGS region has substantially disappeared, indicating the significant improvement in deformation uniformity and further the grain homogenization under the conditions. Microstructure uniformity degree of 2-pass rolled plates did not vary much as the rolling speed varied. On this basis, shear band distribution dominated the deformation behavior during the uniaxial tension of the 2-pass rolled plates. However, microstructure uniformity accompanied by twin distribution played a leading role in stretching the 4-pass rolled plates.

75 FR 19369 - Certain Hot-Rolled Flat-Rolled Carbon Quality Steel Products from Brazil: Preliminary Results of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-14

...-Rolled Carbon Quality Steel Products from Brazil: Preliminary Results of Antidumping Duty Administrative... duty order on certain hot-rolled flat-rolled carbon quality steel products (hot-rolled steel) from... 1, 2008, through February 28, 2009. We preliminarily determine that the sale of hot-rolled steel...

Metallurgical characterization of brass objects from the Akko 1 shipwreck, Israel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ashkenazi, D., E-mail: dana@eng.tau.ac.il; Cvikel, D.; Stern, A.

2014-06-01

The Akko 1 shipwreck was a small Egyptian armed vessel or auxiliary naval brig built in the eastern Mediterranean at the beginning of the 19th century. During the underwater excavations, about 230 brass hook-and-eye closures were found, mainly in the bow area. In addition, 158 brass cases were found, mainly between midships and the aft extremity of the shipwreck. Metallurgical non-destructive and destructive characterizations of selected items were performed, including radiographic testing, XRF, lead isotope analysis, optical microscopy, SEM–EDS and microhardness tests. The hook-and-eye closures and the cases were both found to be made of binary copper–zinc alloy (about 30more » wt.% zinc). While the brass cases were made from rolled sheets, hand-made using simple tools, and joined by tin–lead soldering material, the brass hook-and-eye closures were hand-made from drawn brass wire, and manufactured from commercial drawn brass bars by a cold-working process. The lead isotope analyses suggest different provenances of the raw materials used for making the brass objects, thus the different origins of the ores may hint that the brass wire and sheet were imported to the workshops in which the objects were manufactured. - Highlights: • Brass cases and hook-and-eye closures were retrieved from the Akko 1 shipwreck. • Both types of objects were made of binary copper–zinc alloy (about 30 wt.% zinc). • The cases were hand-made from rolled sheets and joined by tin–lead soldering. • Hook-and-eye closures were made from drawn brass wire manufactured by cold-working. • Lead isotope analyses suggest that the origins of the raw material were diverse.« less

MicroPPT-Based Secondary/Backup ACS for a 160-m, 450-kg Solar Sail Spacecraft

NASA Technical Reports Server (NTRS)

Wie, Bong; Murphy, David

2005-01-01

Solar sail tip-mounted, lightweight pulsed plasma thrusters (PPTs) are proposed for a secondary (or backup) attitude control system (ACS) of a 160-m, 450-kg solar sail spacecraft of the Solar Polar Imager (SPI) mission. A propellantless primary ACS of the SPI sailcraft employs trim control masses running along mast lanyards for pitch/yaw control together with roll stabilizer bars at the mast tips for quadrant tilt (roll) control. The robustness of such a propellantless primary ACS would be further enhanced by a secondary ACS utilizing tip-mounted, lightweight PPTs. The microPPT-based ACS is intended mainly for attitude recovery maneuvers from various off-nominal conditions that cannot be reliably handled by the propellantless primary ACS. However, it can also be employed for: i) the checkout or standby mode prior to and during sail deployment, ii) the post-deployment transition mode (prior to the propellantless primary ACS mode operation), iii) the solar sailing cruise mode of a trimmed sailcraft, and iv) the spin-stabilized, sun-pointing, safe mode. Although a conventional bus ACS is required for the SPI mission as the sail is jettisoned at the start of its science mission phase, the microPPT-based ACS option promises greater redundancy and robustness for the SPI mission. For other sailing missions, where the sail is never jettisoned, this secondary ACS provides a lower-cost, lower-mass propulsion for deployment control and greater redundancy than any traditional reaction-jet control system. This paper presents an overview nf the state--of-the--art microPPT technology, the design requirements of microPPTs for solar sail attitude control, and the preliminary ACS design and simulation results.

75 FR 64246 - Certain Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil: Correction to Notice of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-19

...-Rolled Carbon-Quality Steel Products From Brazil: Correction to Notice of Antidumping Duty Order AGENCY... certain hot-rolled flat-rolled carbon-quality steel products from Brazil. See Antidumping Duty Order: Certain Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil, 67 FR 11093 (March 12, 2002...

49 CFR 393.134 - What are the rules for securing roll-on/roll-off or hook lift containers?

Code of Federal Regulations, 2011 CFR

2011-10-01

... or hook lift containers? 393.134 Section 393.134 Transportation Other Regulations Relating to... for securing roll-on/roll-off or hook lift containers? (a) Applicability. The rules in this section apply to the transportation of roll-on/roll-off or hook lift containers. (b) Securement of a roll-on...

49 CFR 393.134 - What are the rules for securing roll-on/roll-off or hook lift containers?

Code of Federal Regulations, 2010 CFR

2010-10-01

... or hook lift containers? 393.134 Section 393.134 Transportation Other Regulations Relating to... for securing roll-on/roll-off or hook lift containers? (a) Applicability. The rules in this section apply to the transportation of roll-on/roll-off or hook lift containers. (b) Securement of a roll-on...

Rolling-Element Bearings

NASA Technical Reports Server (NTRS)

Hamrock, B. J.; Anderson, W. J.

1983-01-01

Rolling element bearings are a precision, yet simple, machine element of great utility. A brief history of rolling element bearings is reviewed and the type of rolling element bearings, their geometry and kinematics, as well as the materials they are made from and the manufacturing processes they involve are described. Unloaded and unlubricated rolling element bearings, loaded but unlubricated rolling element bearings and loaded and lubricated rolling element bearings are considered. The recognition and understanding of elastohydrodynamic lubrication covered, represents one of the major development in rolling element bearings.

Computer-aided analysis and design of the shape rolling process for producing turbine engine airfoils

NASA Technical Reports Server (NTRS)

Lahoti, G. D.; Akgerman, N.; Altan, T.

1978-01-01

Mild steel (AISI 1018) was selected as model cold-rolling material and Ti-6Al-4V and INCONEL 718 were selected as typical hot-rolling and cold-rolling alloys, respectively. The flow stress and workability of these alloys were characterized and friction factor at the roll/workpiece interface was determined at their respective working conditions by conducting ring tests. Computer-aided mathematical models for predicting metal flow and stresses, and for simulating the shape-rolling process were developed. These models utilize the upper-bound and the slab methods of analysis, and are capable of predicting the lateral spread, roll-separating force, roll torque and local stresses, strains and strain rates. This computer-aided design (CAD) system is also capable of simulating the actual rolling process and thereby designing roll-pass schedule in rolling of an airfoil or similar shape. The predictions from the CAD system were verified with respect to cold rolling of mild steel plates. The system is being applied to cold and hot isothermal rolling of an airfoil shape, and will be verified with respect to laboratory experiments under controlled conditions.

Inflationary dynamics with a smooth slow-roll to constant-roll era transition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Odintsov, S.D.; Oikonomou, V.K., E-mail: odintsov@ieec.uab.es, E-mail: v.k.oikonomou1979@gmail.com

In this paper we investigate the implications of having a varying second slow-roll index on the canonical scalar field inflationary dynamics. We shall be interested in cases that the second slow-roll can take small values and correspondingly large values, for limiting cases of the function that quantifies the variation of the second slow-roll index. As we demonstrate, this can naturally introduce a smooth transition between slow-roll and constant-roll eras. We discuss the theoretical implications of the mechanism we introduce and we use various illustrative examples in order to better understand the new features that the varying second slow-roll index introduces.more » In the examples we will present, the second slow-roll index has exponential dependence on the scalar field, and in one of these cases, the slow-roll era corresponds to a type of α-attractor inflation. Finally, we briefly discuss how the combination of slow-roll and constant-roll may lead to non-Gaussianities in the primordial perturbations.« less

Computer-aided analysis and design of the shape rolling process for producing turbine engine airfoils

NASA Technical Reports Server (NTRS)

Lahoti, G. D.; Akgerman, N.; Altan, T.

1978-01-01

Mild steel (AISI 1018) was selected as model cold rolling material and Ti-6A1-4V and Inconel 718 were selected as typical hot rolling and cold rolling alloys, respectively. The flow stress and workability of these alloys were characterized and friction factor at the roll/workpiece interface was determined at their respective working conditions by conducting ring tests. Computer-aided mathematical models for predicting metal flow and stresses, and for simulating the shape rolling process were developed. These models utilized the upper bound and the slab methods of analysis, and were capable of predicting the lateral spread, roll separating force, roll torque, and local stresses, strains and strain rates. This computer-aided design system was also capable of simulating the actual rolling process, and thereby designing the roll pass schedule in rolling of an airfoil or a similar shape.

A model for prediction of profile and flatness of hot and cold rolled flat products in four-high mills

NASA Astrophysics Data System (ADS)

Overhagen, Christian; Mauk, Paul Josef

2018-05-01

For flat rolled products, the thickness profile in the transversal direction is one of the most important product properties. For further processing, a defined crown of the product is necessary. In the rolling process, several mechanical and thermal influences interact with each other to form the strip shape at the roll gap exit. In the present analysis, a process model for rolling of strip and sheet is presented. The core feature of the process model is a two-dimensional stress distribution model based on von Karman's differential equation. Sub models for the mechanical influences of work roll flattening as well as work and backup roll deflection and the thermal influence of work roll expansion have been developed or extended. The two-dimensional stress distribution serves as an input parameter for the roll deformation models. For work roll flattening, a three-dimensional model based on the Boussinesq problem is adopted, while the work and backup roll deflection, including contact flattening is calculated by means of finite beam elements. The thermal work roll crown is calculated with help of an axisymmetric numerical solution of the heat equation for the work roll, considering azimuthal averaging for the boundary conditions at the work roll surface. Results are presented for hot rolling of a strip in a seven-stand finishing train of a hot strip mill, showing the calculated evolution of the strip profile. A variation of the strip profile from the first to the 20th rolled strip is shown. This variation is addressed to the progressive increase of work roll temperature during the first 20 strips. It is shown that a CVC® system can lead to improvements in strip profile and therefore flatness.

Finite-element model to predict roll-separation force and defects during rolling of U-10Mo alloys

NASA Astrophysics Data System (ADS)

Soulami, Ayoub; Burkes, Douglas E.; Joshi, Vineet V.; Lavender, Curt A.; Paxton, Dean

2017-10-01

A major goal of the Convert Program of the U.S. Department of Energy's National Nuclear Security Administration (DOE/NNSA) is to enable high-performance research reactors to operate with low-enriched uranium rather than the high-enriched uranium currently used. To this end, uranium alloyed with 10 wt% molybdenum (U-10Mo) represents an ideal candidate because of its stable gamma phase, low neutron caption cross section, acceptable swelling response, and predictable irradiation behavior. However, because of the complexities of the fuel design and the need for rolled monolithic U-10Mo foils, new developments in processing and fabrication are necessary. This study used a finite-element code, LS-DYNA, as a predictive tool to optimize the rolling process. Simulations of the hot rolling of U-10Mo coupons encapsulated in low-carbon steel were conducted following two different schedules. Model predictions of the roll-separation force and roll pack thicknesses at different stages of the rolling process were compared with experimental measurements. The study reported here discussed various attributes of the rolled coupons revealed by the model (e.g., waviness and thickness non-uniformity like dog-boning). To investigate the influence of the cladding material on these rolling defects, other cases were simulated: hot rolling with alternative can materials, namely, 304 stainless steel and Zircaloy-2, and bare-rolling. Simulation results demonstrated that reducing the mismatch in strength between the coupon and can material improves the quality of the rolled sheet. Bare-rolling simulation results showed a defect-free rolled coupon. The finite-element model developed and presented in this study can be used to conduct parametric studies of several process parameters (e.g., rolling speed, roll diameter, can material, and reduction).

Effect of Rolling Massage on the Vortex Flow in Blood Vessels with Lattice Boltzmann Simulation

NASA Astrophysics Data System (ADS)

Yi, Hou Hui

The rolling massage manipulation is a classic Chinese Medical Massage, which is a nature therapy in eliminating many diseases. Here, the effect of the rolling massage on the cavity flows in blood vessel under the rolling manipulation is studied by the lattice Boltzmann simulation. The simulation results show that the vortex flows are fully disturbed by the rolling massage. The flow behavior depends on the rolling velocity and the rolling depth. Rolling massage has a better effect on the flows in the cavity than that of the flows in a planar blood vessel. The result is helpful to understand the mechanism of the massage and develop the rolling techniques.

75 FR 62566 - Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil, Japan, and Russia

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-12

...)] Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil, Japan, and Russia AGENCY: United... antidumping duty investigation on hot-rolled steel from Russia. SUMMARY: The Commission hereby gives notice of... suspended investigation on hot-rolled steel from Russia would be likely to lead to continuation or...

76 FR 34101 - Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil, Japan, and Russia

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-10

...] Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil, Japan, and Russia Determinations On...-quality steel products from Russia would be likely to lead to continuation or recurrence of material...) entitled Hot-Rolled Flat-Rolled Carbon-Quality Steel Products from Brazil, Japan, and Russia: Investigation...

75 FR 16504 - Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil, Japan, and Russia

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-01

...)] Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil, Japan, and Russia AGENCY: United... investigation on hot-rolled steel from Russia. SUMMARY: The Commission hereby gives notice that it has...-rolled steel from Russia would be likely to lead to continuation or recurrence of material injury...

75 FR 42782 - Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil, Japan, and Russia

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-22

...)] Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil, Japan, and Russia AGENCY: United... Brazil and Japan, and the suspended investigation on hot-rolled steel from Russia. SUMMARY: The... Japan, and the suspended investigation on hot-rolled steel from Russia would be likely to lead to...

On the Influence of Surface Heterogeneities onto Roll Convection

NASA Astrophysics Data System (ADS)

Gryschka, M.; Drüe, C.; Raasch, S.; Etling, D.

2009-04-01

Roll convection is a common phenomenon in atmospheric convective boundary layers (CBL) with background wind. Roll convection is observed both over land and over sea for different synoptic situations. There is still some debate about the different types of roll convection and their causes or rather the necessary conditions for their appearance. The stability parameter ζ = -zi•L (zi: boundary layer height, L: Monin-Obukhov stability length) is widely used as a predictor for roll convection, since numerous studies suggest that convective rolls only appear when 0 < ζ < 20. In other words, roll development becomes unlikely for strong surface heating and weak vertical wind shear. In contrast to those studies the presence of roll convection in almost any polar cold air outbreak (as can be seen in numerous satellite images as cloud streets) reveals that even for large ζ roll convection can develop. Some studies report roll convection in cold air outbreaks for ζ = 250. Our large eddy simulations (LES) on roll convection suggests that the contrasting results concerning the dependency of roll convection on ζ are due to two different types of roll convection: One type which develops purely by self organization if ζ < 20 ("free rolls") and another type which is triggered by heterogeneities in surface temperature and develops also for large ζ ("forced rolls"). We think that most of the cloud streets observed in polar cold air outbreaks over open water are due to rolls of forced type which are tied to upstream located heterogeneities in the sea-ice distribution. The results of this study suggests that the omission of surface inhomogeneities in previous LES is the reason for the absence of rolls in all LES with strong surface heating and weak vertical wind shear so far. In this contribution we will present a large eddy simulation which successfully represents forced rolls under such conditions.

Static roll-tilt over 5 minutes locally distorts the internal estimate of direction of gravity.

PubMed

Tarnutzer, A A; Bockisch, C J; Straumann, D; Marti, S; Bertolini, G

2014-12-01

The subjective visual vertical (SVV) indicates perceived direction of gravity. Even in healthy human subjects, roll angle-dependent misestimations, roll overcompensation (A-effect, head-roll > 60° and <135°) and undercompensation (E-effect, head-roll < 60°), occur. Previously, we demonstrated that, after prolonged roll-tilt, SVV estimates when upright are biased toward the preceding roll position, which indicates that perceived vertical (PV) is shifted by the prior tilt (Tarnutzer AA, Bertolini G, Bockisch CJ, Straumann D, Marti S. PLoS One 8: e78079, 2013). Hypothetically, PV in any roll position could be biased toward the previous roll position. We asked whether such a "global" bias occurs or whether the bias is "local". The SVV of healthy human subjects (N = 9) was measured in nine roll positions (-120° to +120°, steps = 30°) after 5 min of roll-tilt in one of two adaptation positions (±90°) and compared with control trials without adaptation. After adapting, adjustments were shifted significantly (P < 0.05) toward the previous adaptation position for nearby roll-tilted positions (±30°, ±60°) and upright only. We computationally simulated errors based on the sum of a monotonically increasing function (producing roll undercompensation) and a mixture of Gaussian functions (representing roll overcompensation centered around PV). In combination, the pattern of A- and E-effects could be generated. By shifting the function representing local overcompensation toward the adaptation position, the experimental postadaptation data could be fitted successfully. We conclude that prolonged roll-tilt locally distorts PV rather than globally shifting it. Short-term adaptation of roll overcompensation may explain these shifts and could reflect the brain's strategy to optimize SVV estimates around recent roll positions. Thus postural stability can be improved by visually-mediated compensatory responses at any sustained body-roll orientation. Copyright © 2014 the American Physiological Society.

Prospects of discovering stable double-heavy tetraquarks at a Tera-Z factory

NASA Astrophysics Data System (ADS)

Ali, Ahmed; Parkhomenko, Alexander Ya.; Qin, Qin; Wang, Wei

2018-07-01

Motivated by a number of theoretical considerations, predicting the deeply bound double-heavy tetraquarks T[ u bar d bar ]{ bb }, T[ u bar s bar ]{ bb } and T[ d bar s bar ]{ bb }, we explore the potential of their discovery at Tera-Z factories. Using the process Z → b b bar b b bar , we calculate, employing the Monte Carlo generators MadGraph5_aMC@NLO and Pythia6, the phase space configuration in which the bb pair is likely to fragment as a diquark. In a jet-cone, defined by an invariant mass interval mbb < M T[ q bar qbar‧ ]{ bb } + ΔM, the sought-after tetraquarks T[ q bar qbar‧ ]{ bb } as well as the double-bottom baryons, Ξbb0,-, and Ωbb- , can be produced. Using the heavy quark-diquark symmetry, we estimate B (Z → T[ u bar d bar ]{ bb } + b bar b bar) = (1.2-0.3+1.0) ×10-6, and about a half of this for the T[ u bar s bar ]{ bb } and T[ d bar s bar ]{ bb } . We also present an estimate of their lifetimes using the heavy quark expansion, yielding τ (T[ q bar qbar‧ ]{ bb }) ≃ 800 fs. Measuring the tetraquark masses would require decays, such as T[ u bar d bar ]{ bb } - →B-D-π+, T [ u bar d bar ]{ bb } - → J / ψK‾0B-, T[ u bar d bar ]{ bb } - → J / ψK-B‾0, T[ u bar s bar ]{ bb } - → Ξbc0 Σ-, and T[ d bar s bar ]{ bb } 0 → Ξbc0 Σbar0, with subsequent decay chains in exclusive non-leptonic final states. We estimate a couple of the decay widths and find that the product branching ratios do not exceed 10-5. Hence, a good fraction of these modes will be required for a discovery of T[ q bar qbar‧ ]{ bb } at a Tera-Z factory.

On the impact of forced roll convection on vertical turbulent transport in cold air outbreaks

NASA Astrophysics Data System (ADS)

Gryschka, Micha; Fricke, Jens; Raasch, Siegfried

2014-11-01

We investigated the impact of roll convection on the convective boundary layer and vertical transports in different cold air outbreak (CAO) scenarios using large eddy simulations (LES). The organization of convection into rolls was triggered by upstream heterogeneities in the surface temperature, representing ice and water. By changing the sea ice distribution in our LES, we were able to simulate a roll and a nonroll case for each scenario. Furthermore, the roll wavelength was varied by changing the scale of the heterogeneity. The characteristics of the simulated rolls and cloud streets, such as aspect ratios, orientation of the roll axes, and downstream extensions of single rolls agreed closely with observations in CAO situations. The vertical turbulent fluxes, calculated for each simulation, were decomposed into contributions from rolls and from unorganized turbulence. Even though our results confirmed that rolls triggered by upstream heterogeneities can substantially contribute to vertical turbulent fluxes, the total fluxes were not affected by the rolls.

Coupled thermal-fluid-mechanics analysis of twin roll casting of A7075 aluminum alloy

NASA Astrophysics Data System (ADS)

Lee, Yun-Soo; Kim, Hyoung-Wook; Cho, Jae-Hyung; Chun, Se-Hwan

2017-09-01

Better understanding of temperature distribution and roll separation force during twin roll casting of aluminum alloys is critical to successfully fabricate good quality of aluminum strips. Therefore, the simulation techniques are widely applied to understand the twin roll casting process in a comprehensive way and to reduce the experimental time and cost of trial and error. However, most of the conventional approaches are considered thermally coupled flow, or thermally coupled mechanical behaviors. In this study, a fully coupled thermal-fluid-mechanical analysis of twin roll casting of A7075 aluminum strips was carried out using the finite element method. Temperature profile, liquid fraction and metal flow of aluminum strips with different thickness were predicted. Roll separation force and roll temperatures were experimentally obtained from a pilot-scale twin roll caster, and those results were compared with model predictions. Coupling the fluid of the liquid melt to the thermal and mechanical modeling reasonably predicted roll temperature distribution and roll separation force during twin roll casting.

75 FR 75455 - Certain Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil: Final Results of Full...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-03

...-Rolled Carbon-Quality Steel Products From Brazil: Final Results of Full Sunset Review of Countervailing... of the countervailing duty (CVD) order on certain hot-rolled flat-rolled carbon-quality steel products (hot-rolled steel) from Brazil, pursuant to section 751(c) of the Tariff Act of 1930, as amended...

21 CFR 136.180 - Whole wheat bread, rolls, and buns.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Whole wheat bread, rolls, and buns. 136.180... § 136.180 Whole wheat bread, rolls, and buns. (a) Each of the foods whole wheat bread, graham bread, entire wheat bread, whole wheat rolls, graham rolls, entire wheat rolls, whole wheat buns, graham buns...

The Work Softening by Deformation-Induced Disordering and Cold Rolling of 6.5 wt pct Si Steel Thin Sheets

NASA Astrophysics Data System (ADS)

Wang, Xianglong; Li, Haoze; Zhang, Weina; Liu, Zhenyu; Wang, Guodong; Luo, Zhonghan; Zhang, Fengquan

2016-09-01

As-cast strip of 6.5 wt pct Si steel was fabricated by twin-roll strip casting. After hot rolling at 1323 K (1050 °C), thin sheets with the thickness of 0.35 mm were produced by warm rolling at 373 K (100 °C) with rolling reductions of 15, 25, 35, 45, 55, and 65 pct. Influence of warm rolling reduction on ductility was investigated by room temperature bending test. The measurement of macro-hardness showed that "work softening" could begin when the warm rolling reduction exceeded 35 pct. The room temperature ductility of the thin sheets gradually increased with the increase of warm rolling reductions, and the plastic deformation during bending began to form when the warm rolling reduction was greater than 45 pct, the 65 pct rolled thin sheet exhibited the maximum plastic deformation of about 0.6 pct during bending at room temperature, with a few small dimples having been observed on the fracture surfaces. B2-ordered domains were formed in the 15, 25, 35, 45, and 55 pct rolled specimens, and their average size decreased with the increase of warm rolling reductions. By contrast, no B2-ordered domain could be found in the 65 pct rolled specimen. It had been observed that large-ordered domains could be split into several small parts by the slip of partial super-dislocations during warm rolling, which led to significant decrease of the order degree to cause the phenomenon of deformation-induced disordering. On the basis of these results, cold rolling schedule was developed to successfully fabricate 0.25-mm-thick sheets with good surface qualities and magnetic properties from warm rolled sheets.

Texture and mechanical properties of Al-0.5Mg-1.0Si-0.5Cu alloy sheets manufactured via a cross rolling method

NASA Astrophysics Data System (ADS)

Jeon, Jae-Yeol; Son, Hyeon-Taek; Woo, Kee-Do; Lee, Kwang-Jin

2012-04-01

The relationship between the texture and mechanical properties of 6xxx aluminum alloy sheets processed via cross rolling was investigated. The microstructures of the conventional rolled and cross rolled sheets after annealing were analyzed using optical micrographs (OM). The texture distribution across the thickness in the Al-Mg-Si-Cu alloy, conventional rolled sheets, and cross rolled sheets both before and after annealing was investigated via X-ray texture measurements. The texture was analyzed in three layers from the surface to the center of the sheet. The β-fiber texture of the conventional rolled sheet was typical of the texture obtained using aluminumoll ring. After annealing, the typical β-fiber orientations were changed to recrystallization textures: cube{001}<100> and normal direction (ND)-rotated cubes. However, the texture of the cross rolled sheet was composed of an asymmetrical, rolling direction (RD)-rotated cubes. After annealing, the asymmetrical orientations in the cross rolled sheet were changed to a randomized texture. The average R-value of the annealed cross rolled sheets was higher than that of the conventional rolled sheets. The limit dome height (LDH) test results demonstrated that cross rolling is effective in improving the formability of the Al-Mg-Si-Cu alloy sheets.

40 CFR 467.20 - Applicability; description of the rolling with emulsions subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... rolling with emulsions subcategory. 467.20 Section 467.20 Protection of Environment ENVIRONMENTAL... Rolling With Emulsions Subcategory § 467.20 Applicability; description of the rolling with emulsions... the rolling with emulsions subcategory. ...

40 CFR 467.20 - Applicability; description of the rolling with emulsions subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... rolling with emulsions subcategory. 467.20 Section 467.20 Protection of Environment ENVIRONMENTAL... Rolling With Emulsions Subcategory § 467.20 Applicability; description of the rolling with emulsions... the rolling with emulsions subcategory. ...

CLASSICAL AREAS OF PHENOMENOLOGY: Lattice Boltzmann simulation of behaviour of particles moving in blood vessels under the rolling massage

NASA Astrophysics Data System (ADS)

Yi, Hou-Hui; Yang, Xiao-Feng; Wang, Cai-Feng; Li, Hua-Bing

2009-07-01

The rolling massage is one of the most important manipulations in Chinese massage, which is expected to eliminate many diseases. Here, the effect of the rolling massage on a pair of particles moving in blood vessels under rolling massage manipulation is studied by the lattice Boltzmann simulation. The simulated results show that the motion of each particle is considerably modified by the rolling massage, and it depends on the relative rolling velocity, the rolling depth, and the distance between particle position and rolling position. Both particles' translational average velocities increase almost linearly as the rolling velocity increases, and obey the same law. The increment of the average relative angular velocity for the leading particle is smaller than that of the trailing one. The result is helpful for understanding the mechanism of the massage and to further develop the rolling techniques.

Rolling into spatial disorientation: simulator demonstration of the post-roll (Gillingham) illusion.

PubMed

Nooij, Suzanne A E; Groen, Eric L

2011-05-01

Spatial disorientation (SD) is still a contributing factor in many aviation accidents, stressing the need for adequate SD training scenarios. In this article we focused on the post-roll effect (the sensation of rolling back after a roll maneuver, such as an entry of a coordinated turn) and investigated the effect of roll stimuli on the pilot's ability to stabilize their roll attitude. This resulted in a ground-based demonstration scenario for pilots. The experiments took place in the advanced 6-DOF Desdemona motion simulator, with the subject in a supine position. Roll motions were either fully automated with the subjects blindfolded (BLIND), automated with the subject viewing the cockpit interior (COCKPIT), or self-controlled (LEAD). After the roll stimulus subjects had to cancel all perceived simulator motion without any visual feedback. Both the roll velocity and duration were varied. In 68% of all trials subjects corrected for the perceived motion of rolling back by initiating a roll motion in the same direction as the preceeding roll. The effect was dependent on both rate and duration, in a manner consistent with semicircular canal dynamics. The effect was smallest in the BLIND scenario, but differences between simulation scenarios were non-significant. The results show that the effects of the post-roll illusion on aircraft control can be demonstrated adequately in a flight simulator using an attitude control task. The effect is present even after short roll movements, occurring frequently in flight. Therefore this demonstration is relevant for spatial disorientation training programs for pilots.

Evaluation of Stress Corrosion Cracking Susceptibility Using Fracture Mechanics Techniques, Part 1. [environmental tests of aluminum alloys, stainless steels, and titanium alloys

NASA Technical Reports Server (NTRS)

Sprowls, D. O.; Shumaker, M. B.; Walsh, J. D.; Coursen, J. W.

1973-01-01

Stress corrosion cracking (SSC) tests were performed on 13 aluminum alloys, 13 precipitation hardening stainless steels, and two titanium 6Al-4V alloy forgings to compare fracture mechanics techniques with the conventional smooth specimen procedures. Commercially fabricated plate and rolled or forged bars 2 to 2.5-in. thick were tested. Exposures were conducted outdoors in a seacoast atmosphere and in an inland industrial atmosphere to relate the accelerated tests with service type environments. With the fracture mechanics technique tests were made chiefly on bolt loaded fatigue precracked compact tension specimens of the type used for plane-strain fracture toughness tests. Additional tests of the aluminum alloy were performed on ring loaded compact tension specimens and on bolt loaded double cantilever beams. For the smooth specimen procedure 0.125-in. dia. tensile specimens were loaded axially in constant deformation type frames. For both aluminum and steel alloys comparative SCC growth rates obtained from tests of precracked specimens provide an additional useful characterization of the SCC behavior of an alloy.

How Gaussian can our Universe be?

NASA Astrophysics Data System (ADS)

Cabass, G.; Pajer, E.; Schmidt, F.

2017-01-01

Gravity is a non-linear theory, and hence, barring cancellations, the initial super-horizon perturbations produced by inflation must contain some minimum amount of mode coupling, or primordial non-Gaussianity. In single-field slow-roll models, where this lower bound is saturated, non-Gaussianity is controlled by two observables: the tensor-to-scalar ratio, which is uncertain by more than fifty orders of magnitude; and the scalar spectral index, or tilt, which is relatively well measured. It is well known that to leading and next-to-leading order in derivatives, the contributions proportional to the tilt disappear from any local observable, and suspicion has been raised that this might happen to all orders, allowing for an arbitrarily low amount of primordial non-Gaussianity. Employing Conformal Fermi Coordinates, we show explicitly that this is not the case. Instead, a contribution of order the tilt appears in local observables. In summary, the floor of physical primordial non-Gaussianity in our Universe has a squeezed-limit scaling of kl2/ks2, similar to equilateral and orthogonal shapes, and a dimensionless amplitude of order 0.1 × (ns-1).

Deformation and annealing study of NiCrAlY

NASA Technical Reports Server (NTRS)

Ebert, L. J.; Trela, D. M.

1978-01-01

The elevated temperature properties (tensile and creep) of NiCrALY, a nickel base alloy containing nominally 16% chromium, 4% aluminum, and 2 to 3% yttria (Y2O3) were evaluated and the optimal combination of thermomechanical treatments for maximum creep resistance was determined. Stored strain energy in as-extruded bars (14:1 extrusion ratio) permitted the development of a large grain size in the material when it was annealed at the maximum safe temperature 2450 F (1343 C). With a one-hour anneal at this temperature, the relatively fine grain size of the as-extruded material was changed to one in which the average grain diameter approached 1 mm, and the aspect ratio was about 10. The material was capable of being cold worked (by rolling) in amounts greater than 30% reduction in area. When the cold worked material was given a relaxation treatment, consisting of heating one hour at 1600 F(871 C), and then a high temperature anneal at 2450 F (1343 C) for one hour, both the high temperature strength and the high temperature creep resistance of the material was further enhanced.

Tensile Properties of Molybdenum and Tungsten from 2500 to 3700 F

NASA Technical Reports Server (NTRS)

Hall, Robert W.; Sikora, Paul F.

1959-01-01

Specimens of commercially pure sintered tungsten, arc-cast unalloyed molybdenum, and two arc-cast molybdenum-base alloys (one with 0.5 percent titanium, the other with 0.46 percent titanium and 0.07 percent zirconium) were fabricated from 1/2-inch-diameter rolled or swaged bars. All specimens were evaluated in short-time tensile tests in the as-received condition, and all except the molybdenum-titanium-zirconium alloy were tested after a 30-minute recrystallization anneal at 3800 F in a vacuum of approximately 0.1 micron. Results showed that the tungsten was considerably stronger than either the arc-cast unalloyed molybdenum or the molybdenum-base alloys over the 2500 to 3700 F temperature range. Recrystallization of swaged tungsten at 3800 F considerably reduced its tensile strength at 2500 F. However, above 3100 F, the as-swaged tungsten specimens recrystallized during testing, and had about the same strength as when recrystallized at 3800 F before evaluation. The ductility of molybdenum-base materials was very high at all test temperatures; the ductility of tungsten decreased sharply above about 3120 F.

Defect Analysis of Roll-to-Roll SAIL Manufactured Flexible Display Backplanes

DTIC Science & Technology

2011-01-01

tenting defect through the SAIL process Figure 5: Flexible backplane electrical tester Figure 6: R2R optical inspection system Figure 7: TEM of TFT ...Analysis of Roll-to-Roll SAIL Manufactured Flexible Display...Marcia Almanza-Workman, Robert A. Garcia, HanJun Kim, Ohseung Kwon, Frank Jeffrey HP Laboratories HPL-2011-35 SAIL, flexible displays, roll-to-roll HP

Wind-tunnel investigation at supersonic speeds of a remote-controlled canard missile with a free-rolling-tail brake torque system

NASA Technical Reports Server (NTRS)

Blair, A. B., Jr.

1985-01-01

Wind tunnel tests were conducted at Mach numbers 1.70, 2.16, and 2.86 to determine the static aerodynamic characteristics of a cruciform canard-controlled missile with fixed or free rolling tailfin afterbodies. Mechanical coupling effects of the free-rolling-tail afterbody were investigated by using an electronic electromagnetic brake system providing arbitrary tail-fin brake torques with continuous measurements of tail-to-mainframe torque and tail roll rate. Remote-controlled canards were deflected to provide pitch, yaw, and roll control. Results indicate that the induced rolling moment coefficients due to canard yaw control are reduced and linearized for the free-rolling-tail (free-tail) configuration. The canards of the latter provide conventional roll control for the entire angle-of-attack test range. For the free-tail configuration, the induced rolling moment coefficient due to canard yaw control increased and the canard roll control decreased with increases in brake torque, which simulated bearing friction torque. It appears that a compromise in regard to bearing friction, for example, low-cost bearings with some friction, may allow satisfactory free-tail aerodynamic characteristics that include reductions in adverse rolling-moment coefficients and lower tail roll rates.

Open ended tubing cutters

NASA Technical Reports Server (NTRS)

Girala, A. S. (Inventor)

1981-01-01

A self clamping cutting tool which includes a handle attached to a C-shaped housing is described. Rotatably mounted within the housing is a C-shaped tool body carrying a set of clamping rolls, two support rolls, and an edged cutting roll (64). The support rolls are disposed to one side of the axis of a pipe and the cutting roll is disposed to the other side of a pipe axis so that these rolls contact a pipe at three circumferential points. Cutter advancing apparatus advance the cutting roll toward the support rollers. The support rolls and cutting roll are rotatable independently of the C-shaped housing. A one way ratchet mechanism disposed between the C-shaped housing and the C-shaped tool body permits operation by movement in one rotational direction about the pipe axis.

Evaluation of roll designs on a roll-crusher/ crusher/splitter biomass harvester: test bench results

Treesearch

Colin Ashmore; Donald L. Sirois; Bryce J. Stokes

1987-01-01

Four different roll designs were evaluated on a test bench roll crusher/splitter to determine feeding and crushing efficiencies. For each design, different gap settings for the primary and secondary rolls were tested at two hydraulic cylinder pressures on the primary crush roll to determine their ability to crush and/or feed tree bolts. Seven different diameter classes...

Distinct molecular and cellular contributions to stabilizing selectin-mediated rolling under flow

PubMed Central

Yago, Tadayuki; Leppänen, Anne; Qiu, Haiying; Marcus, Warren D.; Nollert, Matthias U.; Zhu, Cheng; Cummings, Richard D.; McEver, Rodger P.

2002-01-01

Leukocytes roll on selectins at nearly constant velocities over a wide range of wall shear stresses. Ligand-coupled microspheres roll faster on selectins and detach quickly as wall shear stress is increased. To examine whether the superior performance of leukocytes reflects molecular features of native ligands or cellular properties that favor selectin-mediated rolling, we coupled structurally defined selectin ligands to microspheres or K562 cells and compared their rolling on P-selectin. Microspheres bearing soluble P-selectin glycoprotein ligand (sPSGL)-1 or 2-glycosulfopeptide (GSP)-6, a GSP modeled after the NH2-terminal P-selectin–binding region of PSGL-1, rolled equivalently but unstably on P-selectin. K562 cells displaying randomly coupled 2-GSP-6 also rolled unstably. In contrast, K562 cells bearing randomly coupled sPSGL-1 or 2-GSP-6 targeted to a membrane-distal region of the presumed glycocalyx rolled more like leukocytes: rolling steps were more uniform and shear resistant, and rolling velocities tended to plateau as wall shear stress was increased. K562 cells treated with paraformaldehyde or methyl-β-cyclodextrin before ligand coupling were less deformable and rolled unstably like microspheres. Cells treated with cytochalasin D were more deformable, further resisted detachment, and rolled slowly despite increases in wall shear stress. Thus, stable, shear-resistant rolling requires cellular properties that optimize selectin–ligand interactions. PMID:12177042

Hot rolling of thick uranium molybdenum alloys

DOEpatents

DeMint, Amy L.; Gooch, Jack G.

2015-11-17

Disclosed herein are processes for hot rolling billets of uranium that have been alloyed with about ten weight percent molybdenum to produce cold-rollable sheets that are about one hundred mils thick. In certain embodiments, the billets have a thickness of about 7/8 inch or greater. Disclosed processes typically involve a rolling schedule that includes a light rolling pass and at least one medium rolling pass. Processes may also include reheating the rolling stock and using one or more heavy rolling passes, and may include an annealing step.

CROSS-DISCIPLINARY PHYSICS AND RELATED AREAS OF SCIENCE AND TECHNOLOGY: Effect of Rolling Massage on Particle Moving Behaviour in Blood Vessels

NASA Astrophysics Data System (ADS)

Yi, Hou-Hui; Fan, Li-Juan; Yang, Xiao-Feng; Chen, Yan-Yan

2008-09-01

The rolling massage manipulation is a classic Chinese massage, which is expected to eliminate many diseases. Here the effect of the rolling massage on the particle moving property in the blood vessels under the rolling massage manipulation is studied by the lattice Boltzmann simulation. The simulation results show that the particle moving behaviour depends on the rolling velocity, the distance between particle position and rolling position. The average values, including particle translational velocity and angular velocity, increase as the rolling velocity increases almost linearly. The result is helpful to understand the mechanism of the massage and develop the rolling techniques.

Computational Analysis of Ares I Roll Control System Jet Interaction Effects on Rolling Moment

NASA Technical Reports Server (NTRS)

Deere, Karen A.; Pao, S. Paul; Abdol-Hamid, Khaled S.

2011-01-01

The computational flow solver USM3D was used to investigate the jet interaction effects from the roll control system on the rolling moment of the Ares I full protuberance configuration at wind tunnel Reynolds numbers. Solutions were computed at freestream Mach numbers from M = 0.5 to M = 5 at the angle of attack 0deg, at the angle of attack 3.5deg for a roll angle of 120deg, and at the angle of attack 7deg for roll angles of 120deg and 210deg. Results indicate that the RoCS housing provided a beneficial jet interaction effect on vehicle rolling moment for M > or = 0.9. Most of the components downstream of the roll control system housing contributed to jet interaction penalties on vehicle rolling moment.

Small-Molecule Organic Photovoltaic Modules Fabricated via Halogen-Free Solvent System with Roll-to-Roll Compatible Scalable Printing Method.

PubMed

Heo, Youn-Jung; Jung, Yen-Sook; Hwang, Kyeongil; Kim, Jueng-Eun; Yeo, Jun-Seok; Lee, Sehyun; Jeon, Ye-Jin; Lee, Donmin; Kim, Dong-Yu

2017-11-15

For the first time, the photovoltaic modules composed of small molecule were successfully fabricated by using roll-to-roll compatible printing techniques. In this study, blend films of small molecules, BTR and PC 71 BM were slot-die coated using a halogen-free solvent system. As a result, high efficiencies of 7.46% and 6.56% were achieved from time-consuming solvent vapor annealing (SVA) treatment and roll-to-roll compatible solvent additive approaches, respectively. After successful verification of our roll-to-roll compatible method on small-area devices, we further fabricated large-area photovoltaic modules with a total active area of 10 cm 2 , achieving a power conversion efficiency (PCE) of 4.83%. This demonstration of large-area photovoltaic modules through roll-to-roll compatible printing methods, even based on a halogen-free solvent, suggests the great potential for the industrial-scale production of organic solar cells (OSCs).

Rolling Process Modeling Report: Finite-Element Prediction of Roll Separating Force and Rolling Defects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Soulami, Ayoub; Lavender, Curt A.; Paxton, Dean M.

2014-04-23

Pacific Northwest National Laboratory (PNNL) has been investigating manufacturing processes for the uranium-10% molybdenum (U-10Mo) alloy plate-type fuel for the U.S. high-performance research reactors. This work supports the Convert Program of the U.S. Department of Energy’s National Nuclear Security Administration (DOE/NNSA) Global Threat Reduction Initiative. This report documents modeling results of PNNL’s efforts to perform finite-element simulations to predict roll separating forces and rolling defects. Simulations were performed using a finite-element model developed using the commercial code LS-Dyna. Simulations of the hot rolling of U-10Mo coupons encapsulated in low-carbon steel have been conducted following two different schedules. Model predictions ofmore » the roll-separation force and roll-pack thicknesses at different stages of the rolling process were compared with experimental measurements. This report discusses various attributes of the rolled coupons revealed by the model (e.g., dog-boning and thickness non-uniformity).« less

Fault Diagnosis for Centre Wear Fault of Roll Grinder Based on a Resonance Demodulation Scheme

NASA Astrophysics Data System (ADS)

Wang, Liming; Shao, Yimin; Yin, Lei; Yuan, Yilin; Liu, Jing

2017-05-01

Roll grinder is one of the important parts in the rolling machinery, and the grinding precision of roll surface has direct influence on the surface quality of steel strip. However, during the grinding process, the centre bears the gravity of the roll and alternating stress. Therefore, wear or spalling faults are easily observed on the centre, which will lead to an anomalous vibration of the roll grinder. In this study, a resonance demodulation scheme is proposed to detect the centre wear fault of roll grinder. Firstly, fast kurtogram method is employed to help select the sub-band filter parameters for optimal resonance demodulation. Further, the envelope spectrum are derived based on the filtered signal. Finally, two health indicators are designed to conduct the fault diagnosis for centre wear fault. The proposed scheme is assessed by analysing experimental data from a roll grinder of twenty-high rolling mill. The results show that the proposed scheme can effectively detect the centre wear fault of the roll grinder.

Phase transformation kinetics in rolled U-10 wt. % Mo foil: Effect of post-rolling heat treatment and prior γ-UMo grain size

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jana, Saumyadeep; Overman, Nicole; Varga, Tamas

The effect of sub-eutectoid heat treatment on the phase transformation behavior in rolled U-10 wt.percent Mo (U10Mo) foils was systematically investigated. The as-cast 5 mm thick foils were initially homogenized at 900 degrees C for 48 hours and were hot rolled to 2 mm and later cold rolled down to 0.2 mm. Three starting microstructures were evaluated: (i) hot- + cold-rolled to 0.2 mm (as-rolled condition), (ii) hot- + cold-rolled to 0.2 mm + annealed at 700 deg. C for 1 hour, and (iii) hot- + cold-rolled to 0.2 mm + annealed at 1000 deg. C for 60 hours. U10Momore » rolled foils went through various degrees of decomposition when subjected to the sub-eutectoid heat-treatment step and formed a lamellar microstructure through a cellular reaction mostly along the previous γ-UMo grain boundaries.« less

76 FR 22868 - Certain Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil: Final Results of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-25

...-Rolled Carbon-Quality Steel Products From Brazil: Final Results of Countervailing Duty Administrative... administrative review of the countervailing duty order on certain hot-rolled flat-rolled carbon- quality steel...-Quality Steel Products From Brazil: Preliminary Results of Countervailing Duty Administrative Review, 75...

Influence of different kinds of rolling on the crystallographic texture and magnetic induction of a NOG 3 wt% Si steel

NASA Astrophysics Data System (ADS)

Silva, J. M.; Baêta Júnior, E. S.; Moraes, N. R. D. C.; Botelho, R. A.; Felix, R. A. C.; Brandao, L.

2017-01-01

The purpose of this work was to study the influence of different kinds of rolling on the magnetic properties of NOG steel, an electric steel widely used in electrical motors. These properties are highly correlated with the crystallographic texture of the material, which can be changed by rolling. Three kinds of rolling were examined: conventional rolling, cross-rolling and asymmetrical rolling. The crystallographic texture was determined by X-ray diffraction and the magnetic properties were calculated from a theoretical model that related the magnetic induction to crystallographic texture through the anisotropy energy. The results show that cross-rolling yields higher values of magnetic induction than the other processes.

A study of roll attractor and wing rock of delta wings at high angles of attack

NASA Technical Reports Server (NTRS)

Niranjana, T.; Rao, D. M.; Pamadi, Bandu N.

1993-01-01

Wing rock is a high angle of attack dynamic phenomenon of limited cycle motion predominantly in roll. The wing rock is one of the limitations to combat effectiveness of the fighter aircraft. Roll Attractor is the steady state or equilibrium trim angle (phi(sub trim)) attained by the free-to-roll model, held at some angle of attack, and released form rest at a given initial roll (bank) angle (phi(sub O)). Multiple roll attractors are attained at different trim angles depending on initial roll angle. The test facility (Vigyan's low speed wind tunnel) and experimental work is presented here along with mathematical modelling of roll attractor phenomenon and analysis and comparison of predictions with experimental data.

Quantitative analysis and predictive engineering of self-rolling of nanomembranes under anisotropic mismatch strain

NASA Astrophysics Data System (ADS)

Chen, Cheng; Song, Pengfei; Meng, Fanchao; Li, Xiao; Liu, Xinyu; Song, Jun

2017-12-01

The present work presents a quantitative modeling framework for investigating the self-rolling of nanomembranes under different lattice mismatch strain anisotropy. The effect of transverse mismatch strain on the roll-up direction and curvature has been systematically studied employing both analytical modeling and numerical simulations. The bidirectional nature of the self-rolling of nanomembranes and the critical role of transverse strain in affecting the rolling behaviors have been demonstrated. Two fabrication strategies, i.e., third-layer deposition and corner geometry engineering, have been proposed to predictively manipulate the bidirectional rolling competition of strained nanomembranes, so as to achieve controlled, unidirectional roll-up. In particular for the strategy of corner engineering, microfabrication experiments have been performed to showcase its practical application and effectiveness. Our study offers new mechanistic knowledge towards understanding and predictive engineering of self-rolling of nanomembranes with improved roll-up yield.

Preparation of high-strength Al-Mg-Si-Cu-Fe alloy via heat treatment and rolling

NASA Astrophysics Data System (ADS)

Liu, Chong-yu; Yu, Peng-fei; Wang, Xiao-ying; Ma, Ming-zhen; Liu, Ri-ping

2014-07-01

An Al-Mg-Si-Cu-Fe alloy was solid-solution treated at 560°C for 3 h and then cooled by water quenching or furnace cooling. The alloy samples which underwent cooling by these two methods were rolled at different temperatures. The microstructure and mechanical properties of the rolled alloys were investigated by optical microscopy, scanning electron microscopy, transmission electron microscopy, X-ray diffraction analysis, and tensile testing. For the water-quenched alloys, the peak tensile strength and elongation occurred at a rolling temperature of 180°C. For the furnace-cooled alloys, the tensile strength decreased initially, until the rolling temperature of 420°C, and then increased; the elongation increased consistently with increasing rolling temperature. The effects of grain boundary hardening and dislocation hardening on the mechanical properties of these rolled alloys decreased with increases in rolling temperature. The mechanical properties of the 180°C rolling water-quenched alloy were also improved by the presence of β″ phase. Above 420°C, the effect of solid-solution hardening on the mechanical properties of the rolled alloys increased with increases in rolling temperature.

Experiment Research on Hot-Rolling Processing of Nonsmooth Pit Surface.

PubMed

Gu, Yun-Qing; Fan, Tian-Xing; Mou, Jie-Gang; Yu, Wei-Bo; Zhao, Gang; Wang, Evan

2016-01-01

In order to achieve the nonsmooth surface drag reduction structure on the inner polymer coating of oil and gas pipelines and improve the efficiency of pipeline transport, a structural model of the machining robot on the pipe inner coating is established. Based on machining robot, an experimental technique is applied to research embossing and coating problems of rolling-head, and then the molding process rules under different conditions of rolling temperatures speeds and depth are analyzed. Also, an orthogonal experiment analysis method is employed to analyze the different effects of hot-rolling process apparatus on the embossed pits morphology and quality of rolling. The results also reveal that elevating the rolling temperature or decreasing the rolling speed can also improve the pit structure replication rates of the polymer coating surface, and the rolling feed has little effect on replication rates. After the rolling-head separates from the polymer coating, phenomenon of rebounding and refluxing of the polymer coating occurs, which is the reason of inability of the process. A continuous hot-rolling method for processing is used in the robot and the hot-rolling process of the processing apparatus is put in a dynamics analysis.

Experiment Research on Hot-Rolling Processing of Nonsmooth Pit Surface

PubMed Central

Gu, Yun-qing; Fan, Tian-xing; Mou, Jie-gang; Yu, Wei-bo; Zhao, Gang; Wang, Evan

2016-01-01

In order to achieve the nonsmooth surface drag reduction structure on the inner polymer coating of oil and gas pipelines and improve the efficiency of pipeline transport, a structural model of the machining robot on the pipe inner coating is established. Based on machining robot, an experimental technique is applied to research embossing and coating problems of rolling-head, and then the molding process rules under different conditions of rolling temperatures speeds and depth are analyzed. Also, an orthogonal experiment analysis method is employed to analyze the different effects of hot-rolling process apparatus on the embossed pits morphology and quality of rolling. The results also reveal that elevating the rolling temperature or decreasing the rolling speed can also improve the pit structure replication rates of the polymer coating surface, and the rolling feed has little effect on replication rates. After the rolling-head separates from the polymer coating, phenomenon of rebounding and refluxing of the polymer coating occurs, which is the reason of inability of the process. A continuous hot-rolling method for processing is used in the robot and the hot-rolling process of the processing apparatus is put in a dynamics analysis. PMID:27022235

Thermal transport in lithium ion batteries: An experimental investigation of interfaces and granular materials

NASA Astrophysics Data System (ADS)

Gaitonde, Aalok Jaisheela Uday

Increasing usage and recent accidents due to lithium-ion (Li-ion) batteries exploding or catching on fire has inspired research on the characterization and thermal management of these batteries. In cylindrical 18650 cells, heat generated during the battery's charge/discharge cycle is poorly dissipated to the surrounding through its metallic case due to the poor thermal conductivity of the jelly roll, which is spirally wound with many interfaces between electrodes and the polymeric separator. This work presents a technique to measure the thermal conduction across the metallic case-plastic separator interface, which ultimately limits heat transfer out of the jelly roll. The polymeric separator and metallic case are harvested from discharged commercial 18650 battery cells for thermal testing. A miniaturized version of the reference bar method enables measurements of the interface resistance between the case and the separator by establishing a temperature gradient across a multilayer stack consisting of two reference layers of known thermal conductivity and the case-separator sample. The case-separator interfacial conductance is reported for a range of case temperatures and interface pressures. The mean thermal conductance across the case-separator interface is 670 +/- 275 W/(m2K) and no significant temperature or pressure dependence is observed. The effective thermal conductivity of the battery stack is measured to be 0.27 W/m/K and 0.32 W/m/K in linear and radial configurations, respectively. Many techniques for fabricating battery electrodes involve coating particles of the active materials on metallic current collectors. The impact of mechanical shearing on the resultant thermal properties of these packed particle beds during the fabrication process has not yet been studied. Thus, the final portion of this thesis designs and validates a measurement system to measure the effects of mechanical shearing on the thermal conductivity of packed granular beds. This system simultaneously shears the sample while applying a temperature gradient across the particle bed, enabling thermal conductivity measurements using a radial equivalent of the conventional reference bar method. Results of this research, which includes characterization of thermal conductance across the rate limiting separator-case interface, will help improve the design and reliability of lithium ion batteries. Cells of larger dimension and capacity could also be achieved by the improved understanding of thermal transport across the microscopic electrode stack. Better analytic models of the thermal response of the batteries could be constructed, by taking into account the interfacial conductance and thermal conductivity of the electrodes measured in this work. This is of particular importance in the current circumstances, where accidents and safety issues related to lithium ion batteries are on the increase.

Impact of the Lok-bar for High-precision Radiotherapy with Tomotherapy.

PubMed

Hirata, Makoto; Monzen, Hajime; Tamura, Mikoto; Kubo, Kazuki; Matsumoto, Kenji; Hanaoka, Kohei; Okumura, Masahiko; Nishimura, Yasumasa

2018-05-01

Patient immobilization systems are used to establish a reproducible patient position relative to the couch. In this study, the impact of conventional lok-bars for CT-simulation (CIVCO-bar) and treatment (iBEAM-bar) were compared with a novel lok-bar (mHM-bar) in tomotherapy. Verification was obtained as follows: i. artifacts in CT images; ii. dose attenuation rate of lok-bar, compared to without lok-bar; and iii. dose differences between the calculated and measured absorbed doses. With the CIVCO-bar, there were obvious metal artifacts, while there were nearly no artifacts with the mHM-bar. The mean dose attenuation rates with the mHM-bar and iBEAM-bar were 1.31% and 2.28%, and the mean dose difference was 1.55% and 1.66% for mHM-bar and iBEAM-bar. Using the mHM-bar reduced artifacts on the CT image and improved dose attenuation are obtained. The lok-bar needs to be inserted as a structure set in treatment planning with tomotherapy. Copyright© 2018, International Institute of Anticancer Research (Dr. George J. Delinasios), All rights reserved.

77 FR 19619 - Notice of Extension of Time Limit for the Preliminary Results of Administrative Review of the...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-02

... Limit for the Preliminary Results of Administrative Review of the Suspension Agreement on Hot-Rolled... Preliminary Results of Administrative Review of the Suspension Agreement on Hot-Rolled Flat-Rolled Carbon... Suspending the Antidumping Investigation on Hot-Rolled Flat-Rolled Carbon-Quality Steel Products from the...

75 FR 32160 - Certain Hot-Rolled Flat-Rolled Carbon-Quality Steel Products from Brazil: Extension of Time Limit...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-07

... DEPARTMENT OF COMMERCE International Trade Administration [C-351-829] Certain Hot-Rolled Flat... Commerce (the Department) published the countervailing duty order on certain hot-rolled flat- rolled carbon-quality steel products from Brazil. See Agreement Suspending the Countervailing Duty Investigation on Hot...

Why Low Bounce Balls Exhibit High Rolling Resistance

ERIC Educational Resources Information Center

Cross, Rod

2015-01-01

A simple experiment is described to measure the coefficient of rolling friction for a low bounce ball rolling on a horizontal surface. As observed previously by others, the coefficient increased with rolling speed. The energy loss due to rolling friction can be explained in terms of the measured coefficient of restitution for the ball, meaning…

76 FR 15299 - Certain Hot-Rolled Carbon Steel Flat Products From India: Preliminary Rescission of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-21

... DEPARTMENT OF COMMERCE International Trade Administration [C-533-821] Certain Hot-Rolled Carbon... on certain hot-rolled carbon steel flat products from India. See Antidumping or Countervailing Duty... products covered under this order are certain hot-rolled flat- rolled carbon steel flat products of a...

78 FR 42039 - Certain Hot-Rolled Carbon Steel Flat Products From the People's Republic of China: Preliminary...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-15

... DEPARTMENT OF COMMERCE International Trade Administration [A-570-865] Certain Hot-Rolled Carbon... review of the antidumping duty order on certain hot- rolled carbon steel flat products (``hot-rolled...\\ See Notice of Antidumping Duty Order: Certain Hot-Rolled Carbon Steel Flat Products from the People's...

75 FR 27297 - Certain Hot-Rolled Carbon Steel Flat Products from India: Notice of Final Results of Antidumping...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-14

... DEPARTMENT OF COMMERCE International Trade Administration [A-533-820] Certain Hot-Rolled Carbon...'') published the preliminary results of the antidumping duty administrative review for certain hot-rolled carbon steel flat products from India (``Indian Hot-Rolled''). See Certain Hot-Rolled Carbon Steel Flat...

Flexure-based Roll-to-roll Platform: A Practical Solution for Realizing Large-area Microcontact Printing

PubMed Central

Zhou, Xi; Xu, Huihua; Cheng, Jiyi; Zhao, Ni; Chen, Shih-Chi

2015-01-01

A continuous roll-to-roll microcontact printing (MCP) platform promises large-area nanoscale patterning with significantly improved throughput and a great variety of applications, e.g. precision patterning of metals, bio-molecules, colloidal nanocrystals, etc. Compared with nanoimprint lithography, MCP does not require a thermal imprinting step (which limits the speed and material choices), but instead, extreme precision with multi-axis positioning and misalignment correction capabilities for large area adaptation. In this work, we exploit a flexure-based mechanism that enables continuous MCP with 500 nm precision and 0.05 N force control. The fully automated roll-to-roll platform is coupled with a new backfilling MCP chemistry optimized for high-speed patterning of gold and silver. Gratings of 300, 400, 600 nm line-width at various locations on a 4-inch plastic substrate are fabricated at a speed of 60 cm/min. Our work represents the first example of roll-to-roll MCP with high reproducibility, wafer scale production capability at nanometer resolution. The precision roll-to-roll platform can be readily applied to other material systems. PMID:26037147

Lattice Boltzmann Simulation of Blood Flow in Blood Vessels with the Rolling Massage

NASA Astrophysics Data System (ADS)

Yi, Hou-Hui; Xu, Shi-Xiong; Qian, Yue-Hong; Fang, Hai-Ping

2005-12-01

The rolling massage manipulation is a classic Chinese massage, which is expected to improve the circulation by pushing, pulling and kneading of the muscle. A model for the rolling massage manipulation is proposed and the lattice Boltzmann method is applied to study the blood flow in the blood vessels. The simulation results show that the blood flux is considerably modified by the rolling massage and the explicit value depends on the rolling frequency, the rolling depth, and the diameter of the vessel. The smaller the diameter of the blood vessel, the larger the enhancement of the blood flux by the rolling massage. The model, together with the simulation results, is expected to be helpful to understand the mechanism and further development of rolling massage techniques.

Analysis of the differential gene and protein expression profile of the rolled leaf mutant of transgenic rice (Oryza sativa L.).

PubMed

Zhu, Qiuqiang; Yu, Shuguang; Chen, Guanshui; Ke, Lanlan; Pan, Daren

2017-01-01

The importance of leaf rolling in rice (Oryza sativa L.) has been widely recognized. Although several studies have investigated rice leaf rolling and identified some related genes, knowledge of the molecular mechanism underlying rice leaf rolling, especially outward leaf rolling, is limited. Therefore, in this study, differential proteomics and gene expression profiling were used to analyze rolled leaf mutant of transgenic rice in order to investigate differentially expressed genes and proteins related to rice leaf rolling. To this end, 28 differentially expressed proteins related to rolling leaf traits were isolated and identified. Digital expression profiling detected 10 genes related to rice leaf rolling. Some of the proteins and genes detected are involved in lipid metabolism, which is related to the development of bulliform cells, such as phosphoinositide phospholipase C, Mgll gene, and At4g26790 gene. The "omics"-level techniques were useful for simultaneously isolating several proteins and genes related to rice leaf rolling. In addition, the results of the analysis of differentially expressed proteins and genes were closely consistent with those from a corresponding functional analysis of cellular mechanisms; our study findings might form the basis for further research on the molecular mechanisms underlying rice leaf rolling.

Rolling friction—models and experiment. An undergraduate student project

NASA Astrophysics Data System (ADS)

Vozdecký, L.; Bartoš, J.; Musilová, J.

2014-09-01

In this paper the rolling friction (rolling resistance) model is studied theoretically and experimentally in undergraduate level fundamental general physics courses. Rolling motions of a cylinder along horizontal or inclined planes are studied by simple experiments, measuring deformations of the underlay or of the rolling body. The rolling of a hard cylinder on a soft underlay as well as of a soft cylinder on a hard underlay is studied. The experimental data are treated by the open source software Tracker, appropriate for use at the undergraduate level of physics. Interpretation of results is based on elementary considerations comprehensible to university students—beginners. It appears that the commonly accepted model of rolling resistance based on the idea of a warp (little bulge) on the underlay in front of the rolling body does not correspond with experimental results even for the soft underlay and hard rolling body. The alternative model of the rolling resistance is suggested in agreement with experiment and the corresponding concept of the rolling resistance coefficient is presented. In addition to the obtained results we can conclude that the project can be used as a task for students in practical exercises of fundamental general physics undergraduate courses. Projects of similar type effectively contribute to the development of the physical thinking of students.

A model for investigating the influence of road surface texture and tyre tread pattern on rolling resistance

NASA Astrophysics Data System (ADS)

Hoever, Carsten; Kropp, Wolfgang

2015-09-01

The reduction of rolling resistance is essential for a more environmentally friendly road transportation sector. Both tyre and road design can be utilised to reduce rolling resistance. In both cases a reliable simulation tool is needed which is able to quantify the influence of design parameters on the rolling resistance of a tyre rolling on a specific road surface. In this work a previously developed tyre/road interaction model is extended to account for different tread patterns and for losses due to small-scale tread deformation. Calculated contact forces and tyre vibrations for tyre/road interaction under steady-state rolling are used to predict rolling losses in the tyre. Rolling resistance is calculated for a series of different tyre/road combinations. Results are compared with rolling resistance measurements. The agreement between simulations and measurements is generally very good. It is found that both the tyre structure and small-scale tread deformations contribute to the rolling losses. The small-scale contribution depends mainly on the road roughness profile. The mean profile depth of the road surface is identified to correlate very well with the rolling resistance. Additional calculations are performed for non-traditional rubberised road surfaces, however, with mixed results. This possibly indicates the existence of additional loss mechanisms for these surfaces.

Analytical study on web deformation by tension in roll-to-roll printing process

NASA Astrophysics Data System (ADS)

Kang, Y. S.; Hong, M. S.; Lee, S. H.; Jeon, Y. H.; Kang, D.; Lee, N. K.; Lee, M. G.

2017-08-01

Recently, flexible devices have gained high intentions for flexible display, Radio Frequency Identification (RFID), bio-sensor and so on. For manufacturing of the flexible devices, roll-to-roll process is a good candidate because of its low production cost and high productivity. Flexible substrate has a non-uniform deformation distribution by tension. Because the roll-to-roll process carries out a number of overlay printing processes, the deformation affect overlay printing precision and printable areas. In this study, the deformation of flexible substrate was analyzed by using finite element analysis and it was verified through experiments. More deformation occurred in the middle region in the direction parallel to rolling of the flexible substrate. It is confirmed through experiments and analysis that deformation occurs less at the both ends than in the middle region. Based on these results, a hourglass roll is proposed as a mechanical design of the roll to compensate the non-uniform deformation of the flexible substrate. In the hourglass roll, high stiffness material is used in the core and low stiffness material such as an elastic material is wrapped. The diameter of the core roll was designed to be the minimum at the middle and the maximum at both ends. We tried to compensate the non-uniform deformation distribution of the flexible substrate by using the variation of the contact stiffness between the roll and the flexible substrate. Deformation distribution of flexible substrates was confirmed by finite element analysis by applying hourglass roll shape. In the analysis when using the hourglass roll, it is confirmed that the stress distribution is compensated by about 70% and the strain distribution is compensated by about 67% compared to the case using the hourglass roll. To verify the compensation of the non-uniform deformation distribution due to the tension, deformation measurement experiment when using the proposed hourglass roll was carried out. Experiments have shown that the distribution of deformation is compensated by about 34%. From the results, we verified the performance of the proposed.

25 CFR 75.3 - Announcement of revision of roll.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 25 Indians 1 2011-04-01 2011-04-01 false Announcement of revision of roll. 75.3 Section 75.3... ROLL OF THE EASTERN BAND OF CHEROKEE INDIANS, NORTH CAROLINA § 75.3 Announcement of revision of roll... perform the work necessary to revise the membership roll of the Band and such staff has been employed and...

25 CFR 75.3 - Announcement of revision of roll.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Announcement of revision of roll. 75.3 Section 75.3... ROLL OF THE EASTERN BAND OF CHEROKEE INDIANS, NORTH CAROLINA § 75.3 Announcement of revision of roll... perform the work necessary to revise the membership roll of the Band and such staff has been employed and...

The Six Track Scherzer Rolling Lift Bridge…Two double track spans ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

The Six Track Scherzer Rolling Lift Bridge…Two double track spans closed. One double-track span open. Photocopy of plate xvi in Scherzer Rolling Lift Bridge Company, Scherzer Rolling Lift Bridges. - New York, New Haven & Hartford Railroad, Fort Point Channel Rolling Lift Bridge, Spanning Fort Point Channel, Boston, Suffolk County, MA

78 FR 64473 - Certain Hot-Rolled Carbon Steel Flat Products From the People's Republic of China: Final No...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-29

... DEPARTMENT OF COMMERCE International Trade Administration [A-570-865] Certain Hot-Rolled Carbon... review of the antidumping duty order on certain hot- rolled carbon steel flat products (``hot-rolled... of subject merchandise to the United States during the POR. \\1\\ See Certain Hot-Rolled Carbon Steel...

Purification, crystallization and preliminary X-ray analysis of the inverse F-BAR domain of the human srGAP2 protein.

PubMed

Wang, Hongpeng; Zhang, Yan; Zhang, Zhenyi; Jin, Wei Lin; Wu, Geng

2014-01-01

Bin-Amphiphysin-Rvs (BAR) domain proteins play essential roles in diverse cellular processes by inducing membrane invaginations or membrane protrusions. Among the BAR superfamily, the `classical' BAR and Fes/CIP4 homology BAR (F-BAR) subfamilies of proteins usually promote membrane invaginations, whereas the inverse BAR (I-BAR) subfamily generally incur membrane protrusions. Despite possessing an N-terminal F-BAR domain, the srGAP2 protein regulates neurite outgrowth and neuronal migration by causing membrane protrusions reminiscent of the activity of I-BAR domain proteins. In this study, the inverse F-BAR (IF-BAR) domain of human srGAP2 was overexpressed, purified and crystallized. The crystals of the srGAP2 IF-BAR domain protein diffracted to 3.50 Å resolution and belonged to space group P2(1). These results will facilitate further structural determination of the srGAP2 IF-BAR domain and the ultimate elucidation of its peculiar behaviour of inducing membrane protrusions rather than membrane invaginations.

Triple bar, high efficiency mechanical sealer

DOEpatents

Pak, Donald J.; Hawkins, Samantha A.; Young, John E.

2013-03-19

A clamp with a bottom clamp bar that has a planar upper surface is provided. The clamp may also include a top clamp bar connected to the bottom clamp bar, and a pressure distribution bar between the top clamp bar and the bottom clamp bar. The pressure distribution bar may have a planar lower surface in facing relation to the upper surface of the bottom clamp bar. An object is capable of being disposed in a clamping region between the upper surface and the lower surface. The width of the planar lower surface may be less than the width of the upper surface within the clamping region. Also, the pressure distribution bar may be capable of being urged away from the top clamp bar and towards the bottom clamp bar.

Computer-aided roll pass design in rolling of airfoil shapes

NASA Technical Reports Server (NTRS)

Akgerman, N.; Lahoti, G. D.; Altan, T.

1980-01-01

This paper describes two computer-aided design (CAD) programs developed for modeling the shape rolling process for airfoil sections. The first program, SHPROL, uses a modular upper-bound method of analysis and predicts the lateral spread, elongation, and roll torque. The second program, ROLPAS, predicts the stresses, roll separating force, the roll torque and the details of metal flow by simulating the rolling process, using the slab method of analysis. ROLPAS is an interactive program; it offers graphic display capabilities and allows the user to interact with the computer via a keyboard, CRT, and a light pen. The accuracy of the computerized models was evaluated by (a) rolling a selected airfoil shape at room temperature from 1018 steel and isothermally at high temperature from Ti-6Al-4V, and (b) comparing the experimental results with computer predictions. The comparisons indicated that the CAD systems, described here, are useful for practical engineering purposes and can be utilized in roll pass design and analysis for airfoil and similar shapes.

Rolling Tobacco in Banana Leaves, Newspaper, or Copybook Paper Associated With Significant Reduction in Lung Function in Vanuatu.

PubMed

Weitz, Charles A; Olszowy, Kathryn M; Dancause, Kelsey N; Sun, Cheng; Pomer, Alysa; Silverman, Howard; Lee, G; Tarivonda, Len; Chan, Chim W; Kaneko, Akira; Lum, J K; Garruto, Ralph M

2017-04-01

In addition to the widespread availability of packaged cigarettes, the inhabitants of island nations of the Southwest Pacific frequently smoke commercially available loose tobacco using manufactured rolling papers, as well as locally grown tobacco rolled in manufactured rolling paper or wrapped in leaves, copybook paper, and newspaper. In this study, Vanuatu men who smoked local tobacco rolled in leaves, copybook paper, or newspaper showed significantly lower forced vital capacity (FVC), forced expiratory volume in 1 second (FEV 1 ), and FEV 1 /FVC ratios than men who smoked packaged cigarettes, store-bought tobacco rolled in manufactured rolling paper, or who smoked locally grown tobacco rolled in manufactured rolling papers. The addition of toxins from these unusual tobacco-wrapping media produces lung function deficits similar to the pattern noted among tobacco smokers who also inhale smoke from burning biomass. Thus, public health initiatives should consider including strategies addressing the use of wrapping media among smokers in South Pacific island societies.

Flight Test of the F/A-18 Active Aeroelastic Wing Airplane

NASA Technical Reports Server (NTRS)

Voracek, David

2007-01-01

A viewgraph presentation of flight tests performed on the F/A active aeroelastic wing airplane is shown. The topics include: 1) F/A-18 AAW Airplane; 2) F/A-18 AAW Control Surfaces; 3) Flight Test Background; 4) Roll Control Effectiveness Regions; 5) AAW Design Test Points; 6) AAW Phase I Test Maneuvers; 7) OBES Pitch Doublets; 8) OBES Roll Doublets; 9) AAW Aileron Flexibility; 10) Phase I - Lessons Learned; 11) Control Law Development and Verification & Validation Testing; 12) AAW Phase II RFCS Envelopes; 13) AAW 1-g Phase II Flight Test; 14) Region I - Subsonic 1-g Rolls; 15) Region I - Subsonic 1-g 360 Roll; 16) Region II - Supersonic 1-g Rolls; 17) Region II - Supersonic 1-g 360 Roll; 18) Region III - Subsonic 1-g Rolls; 19) Roll Axis HOS/LOS Comparison Region II - Supersonic (open-loop); 20) Roll Axis HOS/LOS Comparison Region II - Supersonic (closed-loop); 21) AAW Phase II Elevated-g Flight Test; 22) Region I - Subsonic 4-g RPO; and 23) Phase II - Lessons Learned

Roll-to-Roll production of carbon nanotubes based supercapacitors

NASA Astrophysics Data System (ADS)

Zhu, Jingyi; Childress, Anthony; Karakaya, Mehmet; Roberts, Mark; Arcilla-Velez, Margarita; Podila, Ramakrishna; Rao, Apparao

2014-03-01

Carbon nanomaterials provide an excellent platform for electrochemical double layer capacitors (EDLCs). However, current industrial methods for producing carbon nanotubes are expensive and thereby increase the costs of energy storage to more than 10 Wh/kg. In this regard, we developed a facile roll-to-roll production technology for scalable manufacturing of multi-walled carbon nanotubes (MWNTs) with variable density on run-of-the-mill kitchen Al foils. Our method produces MWNTs with diameter (heights) between 50-100 nm (10-100 μm), and a specific capacitance as high as ~ 100 F/g in non-aqueous electrolytes. In this talk, the fundamental challenges involved in EDLC-suitable MWNT growth, roll-to-roll production, and device manufacturing will be discussed along with electrochemical characteristics of roll-to-roll MWNTs. Research supported by NSF CMMI Grant1246800.

Effects of Changing Hot Rolling Direction on Microstructure, Texture and Mechanical Properties of Cu-2.7Be Sheets

NASA Astrophysics Data System (ADS)

Zhu, Daibo; Liu, Chuming; Yu, Haijun; Han, Tan

2018-03-01

A hot rolling scheme (cross-rolling and unidirectional rolling) was adopted to process Cu-2.7Be sheets used as multiplier dynodes in photomultiplier. The effects of changing rolling direction on microstructure, texture and mechanical properties were studied by a combination of XRD, EBSD and TEM. It was found that higher copper-type texture and lower brass texture intensity were obtained in the ultimately cross-rolling (CR) sheet compared with the unidirectional rolling (UR) sheet.The EBSD results indicated that the grain orientation from mainly < {101} > for UR sample turns to random for CR sample. Great enhancements in YS and UTS after unidirectional rolling were attributed to the massive and polygonal γ precipitates. The CR sample exhibited lower anisotropy, because of the increase of S and γ precipitates with spherical and tiny shape.

Impact of vertical wind shear on roll structure in idealized hurricane boundary layers

NASA Astrophysics Data System (ADS)

Wang, Shouping; Jiang, Qingfang

2017-03-01

Quasi-two-dimensional roll vortices are frequently observed in hurricane boundary layers. It is believed that this highly coherent structure, likely caused by the inflection-point instability, plays an important role in organizing turbulent transport. Large-eddy simulations are conducted to investigate the impact of wind shear characteristics, such as the shear strength and inflection-point level, on the roll structure in terms of its spectral characteristics and turbulence organization. A mean wind nudging approach is used in the simulations to maintain the specified mean wind shear without directly affecting turbulent motions. Enhancing the radial wind shear expands the roll horizontal scale and strengthens the roll's kinetic energy. Increasing the inflection-point level tends to produce a narrow and sharp peak in the power spectrum at the wavelength consistent with the roll spacing indicated by the instantaneous turbulent fields. The spectral tangential momentum flux, in particular, reaches a strong peak value at the roll wavelength. In contrast, the spectral radial momentum flux obtains its maximum at the wavelength that is usually shorter than the roll's, suggesting that the roll radial momentum transport is less efficient than the tangential because of the quasi-two-dimensionality of the roll structure. The most robust rolls are produced in a simulation with the highest inflection-point level and relatively strong radial wind shear. Based on the spectral analysis, the roll-scale contribution to the turbulent momentum flux can reach 40 % in the middle of the boundary layer.

GRCop-84 Rolling Parameter Study

NASA Technical Reports Server (NTRS)

Loewenthal, William S.; Ellis, David L.

2008-01-01

This report is a section of the final report on the GRCop-84 task of the Constellation Program and incorporates the results obtained between October 2000 and September 2005, when the program ended. NASA Glenn Research Center (GRC) has developed a new copper alloy, GRCop-84 (Cu-8 at.% Cr-4 at.% Nb), for rocket engine main combustion chamber components that will improve rocket engine life and performance. This work examines the sensitivity of GRCop-84 mechanical properties to rolling parameters as a means to better define rolling parameters for commercial warm rolling. Experiment variables studied were total reduction, rolling temperature, rolling speed, and post rolling annealing heat treatment. The responses were tensile properties measured at 23 and 500 C, hardness, and creep at three stress-temperature combinations. Understanding these relationships will better define boundaries for a robust commercial warm rolling process. The four processing parameters were varied within limits consistent with typical commercial production processes. Testing revealed that the rolling-related variables selected have a minimal influence on tensile, hardness, and creep properties over the range of values tested. Annealing had the expected result of lowering room temperature hardness and strength while increasing room temperature elongations with 600 C (1112 F) having the most effect. These results indicate that the process conditions to warm roll plate and sheet for these variables can range over wide levels without negatively impacting mechanical properties. Incorporating broader process ranges in future rolling campaigns should lower commercial rolling costs through increased productivity.

THE MASS PROFILE AND SHAPE OF BARS IN THE SPITZER SURVEY OF STELLAR STRUCTURE IN GALAXIES (S{sup 4}G): SEARCH FOR AN AGE INDICATOR FOR BARS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Taehyun; Lee, Myung Gyoon; Sheth, Kartik

2015-01-20

We have measured the radial light profiles and global shapes of bars using two-dimensional 3.6 μm image decompositions for 144 face-on barred galaxies from the Spitzer Survey of Stellar Structure in Galaxies. The bar surface brightness profile is correlated with the stellar mass and bulge-to-total (B/T) ratio of their host galaxies. Bars in massive and bulge-dominated galaxies (B/T > 0.2) show a flat profile, while bars in less massive, disk-dominated galaxies (B/T ∼ 0) show an exponential, disk-like profile with a wider spread in the radial profile than in the bulge-dominated galaxies. The global two-dimensional shapes of bars, however, are rectangular/boxy, independentmore » of the bulge or disk properties. We speculate that because bars are formed out of disks, bars initially have an exponential (disk-like) profile that evolves over time, trapping more disk stars to boxy bar orbits. This leads bars to become stronger and have flatter profiles. The narrow spread of bar radial profiles in more massive disks suggests that these bars formed earlier (z > 1), while the disk-like profiles and a larger spread in the radial profile in less massive systems imply a later and more gradual evolution, consistent with the cosmological evolution of bars inferred from observational studies. Therefore, we expect that the flatness of the bar profile can be used as a dynamical age indicator of the bar to measure the time elapsed since the bar formation. We argue that cosmic gas accretion is required to explain our results on bar profile and the presence of gas within the bar region.« less

40 CFR 1066.225 - Roll runout and diameter verification procedure.

Code of Federal Regulations, 2013 CFR

2013-07-01

... section. (2) Measure roll diameter using a Pi Tape®. Orient the Pi Tape® to the marker line at the desired measurement location with the Pi Tape® hook pointed outward. Temporarily secure the Pi Tape® to the roll near the hook end with adhesive tape. Slowly turn the roll, wrapping the Pi Tape® around the roll surface...

40 CFR 1066.225 - Roll runout and diameter verification procedure.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) Measure roll diameter using a Pi Tape®. Orient the Pi Tape® to the marker line at the desired measurement location with the Pi Tape® hook pointed outward. Temporarily secure the Pi Tape® to the roll near the hook end with adhesive tape. Slowly turn the roll, wrapping the Pi Tape® around the roll surface. Ensure...

40 CFR 1066.225 - Roll runout and diameter verification procedure.

Code of Federal Regulations, 2012 CFR

2012-07-01

... section. (2) Measure roll diameter using a Pi Tape®. Orient the Pi Tape® to the marker line at the desired measurement location with the Pi Tape® hook pointed outward. Temporarily secure the Pi Tape® to the roll near the hook end with adhesive tape. Slowly turn the roll, wrapping the Pi Tape® around the roll surface...

The measurement of dynamic radii for passenger car tyre

NASA Astrophysics Data System (ADS)

Anghelache, G.; Moisescu, R.

2017-10-01

The tyre dynamic rolling radius is an extremely important parameter for vehicle dynamics, for operation of safety systems as ESP, ABS, TCS, etc., for road vehicle research and development, as well as for validation or as an input parameter of automotive simulations and models. The paper investigates the dynamic rolling radii of passenger car tyre and the influence of rolling speed and inflation pressure on their magnitude. The measurement of dynamic rolling radii has been performed on a chassis dynamometer test rig. The dynamic rolling radii have been measured indirectly, using longitudinal rolling speed and angular velocity of wheel. Due to the subtle effects that the parameters have on rolling radius magnitude, very accurate equipment has to be used. Two different methods have been chosen for measuring the wheel angular velocity: the stroboscopic lamp and the incremental rotary encoder. The paper shows that the stroboscopic lamp has an insufficient resolution, therefore it was no longer used for experimental investigation. The tyre dynamic rolling radii increase with rolling speed and with tyre inflation pressure, but the effect of pressure is more significant. The paper also makes considerations on the viability of simplified formulae from literature for calculating the tyre dynamic rolling radius.

Adaptive attenuation of aliased ground roll using the shearlet transform

NASA Astrophysics Data System (ADS)

Hosseini, Seyed Abolfazl; Javaherian, Abdolrahim; Hassani, Hossien; Torabi, Siyavash; Sadri, Maryam

2015-01-01

Attenuation of ground roll is an essential step in seismic data processing. Spatial aliasing of the ground roll may cause the overlap of the ground roll with reflections in the f-k domain. The shearlet transform is a directional and multidimensional transform that separates the events with different dips and generates subimages in different scales and directions. In this study, the shearlet transform was used adaptively to attenuate aliased and non-aliased ground roll. After defining a filtering zone, an input shot record is divided into segments. Each segment overlaps adjacent segments. To apply the shearlet transform on each segment, the subimages containing aliased and non-aliased ground roll, the locations of these events on each subimage are selected adaptively. Based on these locations, mute is applied on the selected subimages. The filtered segments are merged together, using the Hanning function, after applying the inverse shearlet transform. This adaptive process of ground roll attenuation was tested on synthetic data, and field shot records from west of Iran. Analysis of the results using the f-k spectra revealed that the non-aliased and most of the aliased ground roll were attenuated using the proposed adaptive attenuation procedure. Also, we applied this method on shot records of a 2D land survey, and the data sets before and after ground roll attenuation were stacked and compared. The stacked section after ground roll attenuation contained less linear ground roll noise and more continuous reflections in comparison with the stacked section before the ground roll attenuation. The proposed method has some drawbacks such as more run time in comparison with traditional methods such as f-k filtering and reduced performance when the dip and frequency content of aliased ground roll are the same as those of the reflections.

Effect of intermediate annealing on the microstructure and mechanical property of ZK60 magnesium alloy produced by twin roll casting and hot rolling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Hongmei, E-mail: hmchen@just.edu.cn; Zang, Qianhao; Yu, Hui

2015-08-15

Twin roll cast (designated as TRC in short) ZK60 magnesium alloy strip with 3.5 mm thickness was used in this paper. The TRC ZK60 strip was multi-pass rolled at different temperatures, intermediate annealing heat treatment was performed when the thickness of the strip changed from 3.5 mm to 1 mm, and then continued to be rolled until the thickness reached to 0.5 mm. The effect of intermediate annealing during rolling process on microstructure, texture and room temperature mechanical properties of TRC ZK60 strip was studied by using OM, TEM, XRD and electronic universal testing machine. The introduction of intermediate annealingmore » can contribute to recrystallization in the ZK60 sheet which was greatly deformed, and help to reduce the stress concentration generated in the rolling process. Microstructure uniformity and mechanical properties of the ZK60 alloy sheet were also improved; in particular, the room temperature elongation was greatly improved. When the TRC ZK60 strip was rolled at 300 °C and 350 °C, the room temperature elongation of the rolled sheet with 0.5 mm thickness which was intermediate annealed during the rolling process was increased by 95% and 72% than that of no intermediate annealing, respectively. - Highlights: • Intermediate annealing was introduced during hot rolling process of twin roll cast ZK60 alloy. • Intermediate annealing can contribute to recrystallization and reduce the stress concentration in the deformed ZK60 sheet. • Microstructure uniformity and mechanical properties of the ZK60 sheet were improved, in particular, the room temperature elongation. • The elongation of the rolled ZK60 sheet after intermediate annealed was increased by 95% and 72% than that of no intermediate annealing.« less

Railroad Classification Yard Technology Manual. Volume III. Freight Car Rollability

DOT National Transportation Integrated Search

1981-07-01

The report presents a survey of rolling resistance research, histograms of rolling resistance from five yards, a statistical regression analysis of causal factors affecting rolling resistance, procedures for constructing a rolling resistance histogra...

THE EFFECTS OF $gamma$-IRRADIATION AND ROLLING ON THE TEARING PROPERTIES OF POLYETHYLENE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tsunekawa, Y.; Awatani, J.; Kojima, K.

1961-01-01

Polyethylene samples of 2 mm thickness were gamma irradiated in water. The total dosage for the samples irradiated after the rolling treatraent was 1.5 x lO/sup 5/ r/hr, while the dosage for the saraples irradiated before the rolling was 1.2 x lO/sup 5/ r/hr. The tensile strength of the irradiated and rolled saraple increased with increasing dosage. A comparison of tearing strengths between the rolled samples and the rolled and irradiated samples was raade. (OID)

The role of compressional viscoelasticity in the lubrication of rolling contacts.

NASA Technical Reports Server (NTRS)

Harrison, G.; Trachman, E. G.

1972-01-01

A simple model for the time-dependent volume response of a liquid to an applied pressure step is used to calculate the variation with rolling speed of the traction coefficient in a rolling contact system. Good agreement with experimental results is obtained at rolling speeds above 50 in/sec. At lower rolling speeds a very rapid change in the effective viscosity of the lubricant is predicted. This behavior, in conjunction with shear rate effects, is shown to lead to large errors when experimental data are extrapolated to zero rolling speed.

Multi-stage FE simulation of hot ring rolling

NASA Astrophysics Data System (ADS)

Wang, C.; Geijselaers, H. J. M.; van den Boogaard, A. H.

2013-05-01

As a unique and important member of the metal forming family, ring rolling provides a cost effective process route to manufacture seamless rings. Applications of ring rolling cover a wide range of products in aerospace, automotive and civil engineering industries [1]. Above the recrystallization temperature of the material, hot ring rolling begins with the upsetting of the billet cut from raw stock. Next a punch pierces the hot upset billet to form a hole through the billet. This billet, referred to as preform, is then rolled by the ring rolling mill. For an accurate simulation of hot ring rolling, it is crucial to include the deformations, stresses and strains from the upsetting and piercing process as initial conditions for the rolling stage. In this work, multi-stage FE simulations of hot ring rolling process were performed by mapping the local deformation state of the workpiece from one step to the next one. The simulations of upsetting and piercing stages were carried out by 2D axisymmetric models using adaptive remeshing and element erosion. The workpiece for the ring rolling stage was subsequently obtained after performing a 2D to 3D mapping. The commercial FE package LS-DYNA was used for the study and user defined subroutines were implemented to complete the control algorithm. The simulation results were analyzed and also compared with those from the single-stage FE model of hot ring rolling.

Microstructural evolution in an ultra-fine YAl{sub 2p} reinforced Mg–14Li–3Al composite during warm-rolling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, H.L.; Wu, G.Q.; Zhang, D.C.

2015-06-15

The YAl{sub 2p}/MgLiAl composite prepared by stir casting was initially forged and then rolled at 200 °C to different thicknesses. The microstructural evolution in the composite during warm rolling was investigated by using transmission electron microscope (TEM). It is found that increasing rolling reduction is conducive to the uniform distribution and refinement of the YAl{sub 2} particles. The rolling deformation promoted the precipitation of an α phase, and the α precipitate is semi-coherent to the matrix with an orientation relationship to the β matrix as: (0002){sub α}‖(110){sub β}. In addition, many nano-sized YAl particles with a cubic shape were foundmore » in the matrix of the composite with a high rolling reduction due to the diffusion of Y from YAl{sub 2} to the matrix, which reacted with the Al in the matrix during warm rolling. - Highlights: • The reinforcement YAl{sub 2} particles were distributed more uniformly in the matrix and refined with increasing rolling reduction. • The rolling deformation promoted and refined the precipitation of an α phase with increasing rolling reduction. • Many nano-sized YAl phases were produced and distributed in the matrix of the composite at a high rolling reduction.« less

Finite-element model to predict roll-separation force and defects during rolling of U-10Mo alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Soulami, Ayoub; Burkes, Douglas E.; Joshi, Vineet V.

This study used a finite element code, LSDYNA, as a predictive tool to optimize the rolling process. Simulations of the hot rolling of U-10Mo coupons encapsulated in low-carbon steel were conducted following two different schedules. Model predictions of the roll-separation force and roll pack thicknesses at different stages of the rolling process were compared with experimental measurements. The study reported here discussed various attributes of the rolled coupons revealed by the model (e.g., waviness and thickness non-uniformity like dog boning). To investigate the influence of the cladding material on these rolling defects, other cases were simulated:  hot rolling with alternative can materials, namely, 304 stainless steel and Zircaloy-2, and bare-rolling.

Membrane-Sculpting BAR Domains Generate Stable Lipid Microdomains

PubMed Central

Zhao, Hongxia; Michelot, Alphée; Koskela, Essi V.; Tkach, Vadym; Stamou, Dimitrios; Drubin, David G.; Lappalainen, Pekka

2014-01-01

SUMMARY Bin-Amphiphysin-Rvs (BAR) domain proteins are central regulators of many cellular processes involving membrane dynamics. BAR domains sculpt phosphoinositide-rich membranes to generate membrane protrusions or invaginations. Here, we report that, in addition to regulating membrane geometry, BAR domains can generate extremely stable lipid microdomains by “freezing” phosphoinositide dynamics. This is a general feature of BAR domains, because the yeast endocytic BAR and Fes/CIP4 homology BAR (F-BAR) domains, the inverse BAR domain of Pinkbar, and the eisosomal BAR protein Lsp1 induced phosphoinositide clustering and halted lipid diffusion, despite differences in mechanisms of membrane interactions. Lsp1 displays comparable low diffusion rates in vitro and in vivo, suggesting that BAR domain proteins also generate stable phosphoinositide microdomains in cells. These results uncover a conserved role for BAR superfamily proteins in regulating lipid dynamics within membranes. Stable microdomains induced by BAR domain scaffolds and specific lipids can generate phase boundaries and diffusion barriers, which may have profound impacts on diverse cellular processes. PMID:24055060

1. EXTERIOR VIEW OF BUILDING THAT HOUSES THE HOT ROLL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. EXTERIOR VIEW OF BUILDING THAT HOUSES THE HOT ROLL MILL, ALSO KNOWN AS THE NO. 31 HOT ROLL MILL; LOOKING SOUTHWEST - American Brass Company, Kenosha Works, Hot Roll Mill, Kenosha, Kenosha County, WI

Increased compactibility of acetames after roll compaction.

PubMed

Kuntz, Theresia; Schubert, Martin A; Kleinebudde, Peter

2011-01-01

A common technique for manufacturing granules in a continuous way is the combination of roll compaction and subsequent milling. Roll compaction can considerably impact tableting performance of a material. The purpose of this study was to investigate the influence of roll compaction/dry granulation on the compaction behavior of acetames, a class of active pharmaceutical substances, which are mainly used for the treatment of central nervous diseases. Some representatives of acetames were roll compacted and then compressed into tablets. Compactibility of granules was compared with the compaction behavior of the directly compressed drug powders. In contrast to many other materials, the roll compaction step induced an increase in compactibility for all investigated acetames. Specific surface areas of the untreated and the roll compacted drugs were determined by nitrogen adsorption. The raise in compactibility observed was accompanied by an increase in specific surface area during roll compaction. Copyright © 2010 Elsevier B.V. All rights reserved.

Research and industrialization of near-net rolling technology used in shaft parts

NASA Astrophysics Data System (ADS)

Hu, Zhenghuan; Wang, Baoyu; Zheng, Zhenhua

2017-11-01

Shaft part rolling is an efficient and green nearnet shaping technology offering many advantages, including high production efficiency, high material utilization rate, high product quality, and excellent production environment. In this paper, the features of shaft part rolling are introduced along with the working principles of two main shaft part rolling technologies, namely, cross wedge rolling (CWR) and skew rolling (SR). In relation to this technology, some R&D achievements gained by the University of Science and Technology Beijing are summarized. Finally, the latest developments in shaft part rolling are presented, including SR steel balls, precise forming of camshaft blank by CWR, SR phosphorous copper balls at room temperature, and CWR hollow axle sleeve. Although the shaft part rolling technology has been widely used in China, it only accounts for about 15% of applicable parts at present. Nevertheless, this technology has broad application prospects.

Research and industrialization of near-net rolling technology used in shaft parts

NASA Astrophysics Data System (ADS)

Hu, Zhenghuan; Wang, Baoyu; Zheng, Zhenhua

2018-03-01

Shaft part rolling is an efficient and green nearnet shaping technology offering many advantages, including high production efficiency, high material utilization rate, high product quality, and excellent production environment. In this paper, the features of shaft part rolling are introduced along with the working principles of two main shaft part rolling technologies, namely, cross wedge rolling (CWR) and skew rolling (SR). In relation to this technology, some R&D achievements gained by the University of Science and Technology Beijing are summarized. Finally, the latest developments in shaft part rolling are presented, including SR steel balls, precise forming of camshaft blank by CWR, SR phosphorous copper balls at room temperature, and CWR hollow axle sleeve. Although the shaft part rolling technology has been widely used in China, it only accounts for about 15% of applicable parts at present. Nevertheless, this technology has broad application prospects.

Measurement method for roll angular displacement with a high resolution by using diffraction gratings and a heterodyne interferometer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tang, Shanzhi, E-mail: shanzhit@gmail.com; School of Mechanical Engineering, Xi'an Jiaotong University, Xi'an 710049; Wang, Zhao

The roll angle measurement is difficult to be achieved directly using a typical commercial interferometer due to its low sensitivity in axial direction, where the axial direction is orthogonal to the plane of the roll angular displacement. A roll angle measurement method combined diffraction gratings with a laser heterodyne interferometer is discussed in this paper. The diffraction grating placed in the plane of a roll angular displacement and the interferometer arranged in the plane's orthogonal direction, constitute the measurement pattern for the roll angle with high resolution. The roll angular displacement, considered as the linear, can be tested precisely whenmore » the corresponding angle is very small. Using the proposed method, the angle roll measurement obtains the high resolution of 0.002{sup ″}. Experiment has proved its feasibility and practicability.« less

Complications with computer-aided designed/computer-assisted manufactured titanium and soldered gold bars for mandibular implant-overdentures: short-term observations.

PubMed

Katsoulis, Joannis; Wälchli, Julia; Kobel, Simone; Gholami, Hadi; Mericske-Stern, Regina

2015-01-01

Implant-overdentures supported by rigid bars provide stability in the edentulous atrophic mandible. However, fractures of solder joints and matrices, and loosening of screws and matrices were observed with soldered gold bars (G-bars). Computer-aided designed/computer-assisted manufactured (CAD/CAM) titanium bars (Ti-bars) may reduce technical complications due to enhanced material quality. To compare prosthetic-technical maintenance service of mandibular implant-overdentures supported by CAD/CAM Ti-bar and soldered G-bar. Edentulous patients were consecutively admitted for implant-prosthodontic treatment with a maxillary complete denture and a mandibular implant-overdenture connected to a rigid G-bar or Ti-bar. Maintenance service and problems with the implant-retention device complex and the prosthesis were recorded during minimally 3-4 years. Annual peri-implant crestal bone level changes (ΔBIC) were radiographically assessed. Data of 213 edentulous patients (mean age 68 ± 10 years), who had received a total of 477 tapered implants, were available. Ti-bar and G-bar comprised 101 and 112 patients with 231 and 246 implants, respectively. Ti-bar mostly exhibited distal bar extensions (96%) compared to 34% of G-bar (p < .001). Fracture rate of bars extensions (4.7% vs 14.8%, p < .001) and matrices (1% vs 13%, p < .001) was lower for Ti-bar. Matrices activation was required 2.4× less often in Ti-bar. ΔBIC remained stable for both groups. Implant overdentures supported by soldered gold bars or milled CAD/CAM Ti-bars are a successful treatment modality but require regular maintenance service. These short-term observations support the hypothesis that CAD/CAM Ti-bars reduce technical complications. Fracture location indicated that the titanium thickness around the screw-access hole should be increased. © 2013 Wiley Periodicals, Inc.

Scroll bar growth on the coastal Trinity River, TX, USA

NASA Astrophysics Data System (ADS)

Mason, J.; Hassenruck-Gudipati, H. J.; Mohrig, D. C.

2017-12-01

The processes leading to the formation and growth of scroll bars remain relatively mysterious despite how often they are referenced in fluvial literature. Their definition is descriptive; they are characterized as arcuate topographic highs present on the inner banks of channel bends on meandering rivers, landward of point bars. Often, they are used as proxies for previous positions of point bars. This assumption of a one-to-one correspondence between point bars and scroll bars should be reconsidered as 1) planform curvature for scroll bars is consistently smaller than the curvature for adjacent point bars, and 2) deposition on the scroll bar is typically distinct and disconnected from the adjacent point bar deposition. Results from time-lapse airborne lidar data as well as from trenches through five separate scroll bar - point bar pairings on the Trinity River in east TX, USA, will be discussed in relation to formative scroll bar processes and their connection to point bars. On the lidar difference map, scroll bar growth appears as a strip of increased deposition flanked on both the land- and channel-ward sides by areas with no or limited deposition. Trenches perpendicular to these scrolls typically show a base of dune-scale cross stratification interpreted to be associated with a previous position of the point bar. These dune sets are overlain by sets of climbing-ripple cross-strata that form the core of the modern scroll bar and preserve a record of multiple transport directions (away from, towards, and parallel to the channel). Preliminary Trinity River grain-size analyses show that the constructional scrolls are enriched in all grain sizes less than 250 microns in diameter, while point bars are enriched in all grain sizes above this cut off. Scroll bars are hypothesized to be akin to levees along the inner banks of channels-flow expansion caused by the presence of point bars induces deposition of suspended sediment that defines the positions of the scroll bars.

Interaction between a Mg17Al12 precipitate and { 10\\bar 12} < 10\\bar 12 > twin boundary in magnesium alloys

NASA Astrophysics Data System (ADS)

Li, B.; Mathaudhu, S. N.

Interactions between Mg17Al12 precipitates and { 10\\bar 12} < 10\\bar 1\\bar 1 > twin boundaries (TBs) in magnesium were studied by molecular dynamics simulations. The results obtained agree well with experimental observations in which precipitates can be entirely engulfed by { 10\\bar 12} < 10\\bar 1\\bar 1 > twins without being sheared. Structural analysis of the TBs in the atomic scale shows that the TBs are extremely incoherent during twin growth and highly deviate from the { 10\\bar 12} twinning plane as previously observed in a number of experiments. The simulation studies indicate that { 10\\bar 12} < 10\\bar 1\\bar 1 > twinning was accomplished solely by atomic shuffling that converts the parent lattice to the twin lattice without involving twinning dislocations, resulting in zero shear strain at the TBs.

75 FR 36363 - Procurement List: Proposed Additions and Deletions

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-25

...-ply, 8'' x 350' rolls, white NSN: 8540-00-NIB-0061--Jumbo Roll Toilet Tissue, 1 ply, 3.7'' x 2000' NSN: 8540-00-NIB-0063--Jumbo Roll Toilet Tissue, 2 ply, 3.7'' x 1000' NSN: 8540-00-NIB-0007--Jumbo Roll Toilet Tissue, 2 ply, 3.7'' x 2000', 12'' dia. Roll NSN: 8540-00-NIB-0064--Center-Pull Paper Towel, 2-ply...

Bar dimensions and bar shapes in estuaries

NASA Astrophysics Data System (ADS)

Leuven, Jasper; Kleinhans, Maarten; Weisscher, Steven; van der Vegt, Maarten

2016-04-01

Estuaries cause fascinating patterns of dynamic channels and shoals. Intertidal sandbars are valuable habitats, whilst channels provide access to harbors. We still lack a full explanation and classification scheme for the shapes and dimensions of bar patterns in natural estuaries, in contrast with bars in rivers. Analytical physics-based models suggest that bar length in estuaries increases with flow velocity, tidal excursion length or estuary width, depending on which model. However, these hypotheses were never validated for lack of data and experiments. We present a large dataset and determine the controls on bar shape and dimensions in estuaries, spanning bar lengths from centimeters (experiments) to 10s of kilometers length. First, we visually identified and classified 190 bars, measured their dimensions (width, length, height) and local braiding index. Data on estuarine geometry and tidal characteristics were obtained from governmental databases and literature on case studies. We found that many complex bars can be seen as simple elongated bars partly cut by mutually evasive ebb- and flood-dominated channels. Data analysis shows that bar dimensions scale with estuary dimensions, in particular estuary width. Breaking up the complex bars in simple bars greatly reduced scatter. Analytical bar theory overpredicts bar dimensions by an order of magnitude in case of small estuarine systems. Likewise, braiding index depends on local width-to-depth ratio, as was previously found for river systems. Our results suggest that estuary dimensions determine the order of magnitude of bar dimensions, while tidal characteristics modify this. We will continue to model bars numerically and experimentally. Our dataset on tidal bars enables future studies on the sedimentary architecture of geologically complex tidal deposits and enables studying effects of man-induced perturbations such as dredging and dumping on bar and channel patterns and habitats.

Impact of Partial and Comprehensive Smoke-Free Regulations on Indoor Air Quality in Bars

PubMed Central

Kim, Jeonghoon; Ban, Hyunkyung; Hwang, Yunhyung; Ha, Kwonchul; Lee, Kiyoung

2016-01-01

In Korea, smoke-free regulations have been gradually implemented in bars based on venue size. Smoking bans were implemented in 2013 for bars ≥150 m2, in 2014 for bars ≥100 m2, and in 2015 for bars of all sizes. The purpose of this study was to determine indoor fine particle (PM2.5) concentrations in bars before and after implementation of the smoke-free policies based on venue size. Indoor PM2.5 concentrations were measured with real-time aerosol monitors at four time points: (1) pre-regulation (n = 75); (2) after implementing the ban in bars ≥150 m2 (n = 75); (3) after implementing the ban in bars ≥100 m2 (n = 107); and (4) when all bars were smoke-free (n = 79). Our results showed that the geometric mean of the indoor PM2.5 concentrations of all bars decreased from 98.4 μg/m3 pre-regulation to 79.5, 42.9, and 26.6 μg/m3 after the ban on smoking in bars ≥150 m2, ≥100 m2, and all bars, respectively. Indoor PM2.5 concentrations in bars of each size decreased only after the corresponding regulations were implemented. Although smoking was not observed in Seoul bars after smoking was banned in all bars, smoking was observed in 4 of 21 bars in Changwon. Our study concludes that the greatest decrease in PM2.5 concentrations in bars was observed after the regulation covering all bars was implemented. However, despite the comprehensive ban, smoking was observed in bars in Changwon. Strict compliance with the regulations is needed to improve indoor air quality further. PMID:27472349

Impact of Partial and Comprehensive Smoke-Free Regulations on Indoor Air Quality in Bars.

PubMed

Kim, Jeonghoon; Ban, Hyunkyung; Hwang, Yunhyung; Ha, Kwonchul; Lee, Kiyoung

2016-07-26

In Korea, smoke-free regulations have been gradually implemented in bars based on venue size. Smoking bans were implemented in 2013 for bars ≥150 m², in 2014 for bars ≥100 m², and in 2015 for bars of all sizes. The purpose of this study was to determine indoor fine particle (PM2.5) concentrations in bars before and after implementation of the smoke-free policies based on venue size. Indoor PM2.5 concentrations were measured with real-time aerosol monitors at four time points: (1) pre-regulation (n = 75); (2) after implementing the ban in bars ≥150 m² (n = 75); (3) after implementing the ban in bars ≥100 m² (n = 107); and (4) when all bars were smoke-free (n = 79). Our results showed that the geometric mean of the indoor PM2.5 concentrations of all bars decreased from 98.4 μg/m³ pre-regulation to 79.5, 42.9, and 26.6 μg/m³ after the ban on smoking in bars ≥150 m², ≥100 m², and all bars, respectively. Indoor PM2.5 concentrations in bars of each size decreased only after the corresponding regulations were implemented. Although smoking was not observed in Seoul bars after smoking was banned in all bars, smoking was observed in 4 of 21 bars in Changwon. Our study concludes that the greatest decrease in PM2.5 concentrations in bars was observed after the regulation covering all bars was implemented. However, despite the comprehensive ban, smoking was observed in bars in Changwon. Strict compliance with the regulations is needed to improve indoor air quality further.

Comparison of the passivity between cast alloy and laser-welded titanium overdenture bars.

PubMed

Paiva, Jose; Givan, Daniel A; Broome, James C; Lemons, Jack E; McCracken, Michael S

2009-12-01

The purpose of this study was to investigate the fit of cast alloy overdenture and laser-welded titanium-alloy bars by measuring induced strain upon tightening of the bars on a master cast as well as a function of screw tightening sequence. Four implant analogs were secured into Type IV dental stone to simulate a mandibular edentulous patient cast, and two groups of four overdenture bars were fabricated. Group I was four cast alloy bars and Group II was four laser-welded titanium bars. The cast alloy bars included Au-Ag-Pd, Pd-Ag-Au, Au-Ag-Cu-Pd, and Ag-Pd-Cu-Au, while the laser-welded bars were all Ti-Al-V alloy. Bars were made from the same master cast, were torqued into place, and the total strain in the bars was measured through five strain gauges bonded to the bar between the implants. Each bar was placed and torqued 27 times to 30 Ncm per screw using three tightening sequences. Data were processed through a strain amplifier and analyzed by computer using StrainSmart software. Data were analyzed by ANOVA and Tukey's post hoc test. Significant differences were found between alloy types. Laser-welded titanium bars tended to have lower strains than corresponding cast bars, although the Au-Ag-Pd bar was not significantly different. The magnitudes of total strain were the least when first tightening the ends of the bar. The passivity of implant overdenture bars was evaluated using total strain of the bar when tightening. Selecting a high modulus of elasticity cast alloy or use of laser-welded bar design resulted in the lowest average strain magnitudes. While the effect of screw tightening sequence was minimal, tightening the distal ends first demonstrated the lowest strain, and hence the best passivity.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Joshi, Vineet V.; Paxton, Dean M.; Lavender, Curt A.

Over the past several years Pacific Northwest National Laboratory (PNNL) has been actively involved in supporting the U.S. Department of Energy National Nuclear Security Administration Office of Material Management and Minimization (formerly Global Threat Reduction Initiative). The U.S. High- Power Research Reactor (USHPRR) project is developing alternatives to existing highly enriched uranium alloy fuel to reduce the proliferation threat. One option for a high-density metal fuel is uranium alloyed with 10 wt% molybdenum (U-10Mo). Forming the U-10Mo fuel plates/foils via rolling is an effective technique and is actively being pursued as part of the baseline manufacturing process. The processing ofmore » these fuel plates requires systematic investigation/understanding of the pre- and post-rolling microstructure, end-state mechanical properties, residual stresses, and defects, their effect on the mill during processing, and eventually, their in-reactor performance. In the work documented herein, studies were conducted to determine the effect of cold and hot rolling the as-cast and homogenized U-10Mo on its microstructure and hardness. The samples were homogenized at 900°C for 48 h, then later annealed for several durations and temperatures to investigate the effect on the material’s microstructure and hardness. The rolling of the as-cast plate, both hot and cold, was observed to form a molybdenum-rich and -lean banded structure. The cold rolling was ineffective, and in some cases exacerbated the as-cast defects. The grains elongated along the rolling direction and formed a pancake shape, while the carbides fractured perpendicularly to the rolling direction and left porosity between fractured particles of UC. The subsequent annealing of these samples at sub-eutectoid temperatures led to rapid precipitation of the ' lamellar phase, mainly in the molybdenum-lean regions. Annealing the samples above the eutectoid temperature did not refine the grain size or the banded microstructure. However, annealing the samples led to quick recovery in hardness as evidenced by a drop in Vickers hardness of 20%. Hot rolling was performed at 650 and 800°C. The hot-rolling mill loads (load separation force) were approximately 40 to 50% less than the cold-rolling for the same reduction and thickness. It was observed that hot rolling the samples with 50% or more reduction in thickness were responsible for dynamic recrystallization in the hot-rolled samples and led to grain refinement. Unlike the cold-rolled samples, the hot-rolled samples did not fracture the carbides and appeared to heal the casting defects. The recovery phenomenon was similar to the cold-rolled samples above the eutectoid temperatures, but owing to the refined grain size, the precipitation of the lamellar phase was far more rapid in these samples and the hardness increased more rapidly than in the cold rolled sample when heated below the eutectoid temperature. The data generated from these rolling efforts has been used to make the process modeling efforts more robust and applicable to all USHPRR partner rolling mills. The flow stress for cold rolling the samples was determined to be between 170-190 ksi, with frictional forces between 0.2 and 0.4 for the PNNL mill. The measured roll separation forces and those simulated using finite element methods for hot and cold rolling for the PNNL rolling mill were in good agreement.« less

Assessment of flat rolling theories for the use in a model-based controller for high-precision rolling applications

NASA Astrophysics Data System (ADS)

Stockert, Sven; Wehr, Matthias; Lohmar, Johannes; Abel, Dirk; Hirt, Gerhard

2017-10-01

In the electrical and medical industries the trend towards further miniaturization of devices is accompanied by the demand for smaller manufacturing tolerances. Such industries use a plentitude of small and narrow cold rolled metal strips with high thickness accuracy. Conventional rolling mills can hardly achieve further improvement of these tolerances. However, a model-based controller in combination with an additional piezoelectric actuator for high dynamic roll adjustment is expected to enable the production of the required metal strips with a thickness tolerance of +/-1 µm. The model-based controller has to be based on a rolling theory which can describe the rolling process very accurately. Additionally, the required computing time has to be low in order to predict the rolling process in real-time. In this work, four rolling theories from literature with different levels of complexity are tested for their suitability for the predictive controller. Rolling theories of von Kármán, Siebel, Bland & Ford and Alexander are implemented in Matlab and afterwards transferred to the real-time computer used for the controller. The prediction accuracy of these theories is validated using rolling trials with different thickness reduction and a comparison to the calculated results. Furthermore, the required computing time on the real-time computer is measured. Adequate results according the prediction accuracy can be achieved with the rolling theories developed by Bland & Ford and Alexander. A comparison of the computing time of those two theories reveals that Alexander's theory exceeds the sample rate of 1 kHz of the real-time computer.

Comparative study on the corrosion behavior of the cold rolled and hot rolled low-alloy steels containing copper and antimony in flue gas desulfurization environment

NASA Astrophysics Data System (ADS)

Park, S. A.; Kim, J. G.; He, Y. S.; Shin, K. S.; Yoon, J. B.

2014-12-01

The correlation between the corrosion and microstructual characteristics of cold rolled and hot rolled low-alloy steels containing copper and antimony was established. The corrosion behavior of the specimens used in flue gas desulfurization systems was examined by electrochemical and weight loss measurements in an aggressive solution of 16.9 vol % H2SO4 + 0.35 vol % HCl at 60°C, pH 0.3. It has been shown that the corrosion rate of hot rolled steel is lower than that of cold rolled steel. The corrosion rate of cold rolled steel was increased by grain refinement, inclusion formation, and preferred grain orientation.

Digitalization in roll forming manufacturing

NASA Astrophysics Data System (ADS)

Sedlmaier, A.; Dietl, T.; Ferreira, P.

2017-09-01

Roll formed profiles are used in automotive chassis production as building blocks for the body-in-white. The ability to produce profiles with discontinuous cross sections, both in width and in depth, allows weight savings in the final automotive chassis through the use of load optimized cross sections. This has been the target of the 3D Roll Forming process. A machine concept is presented where a new forming concept for roll formed parts in combination with advanced robotics allowing freely positioned roll forming tooling in 3D space enables the production of complex shapes by roll forming. This is a step forward into the digitalization of roll forming manufacturing by making the process flexible and capable of rapid prototyping and production of small series of parts. Moreover, data collection in a large scale through the control system and integrated sensors lead to an increased understanding of the process and provide the basis to develop self-optimizing roll forming machines, increasing the productivity, quality and predictability of the roll-forming process. The first parts successfully manufactured with this new forming concept are presented.

Inflation with a smooth constant-roll to constant-roll era transition

NASA Astrophysics Data System (ADS)

Odintsov, S. D.; Oikonomou, V. K.

2017-07-01

In this paper, we study canonical scalar field models, with a varying second slow-roll parameter, that allow transitions between constant-roll eras. In the models with two constant-roll eras, it is possible to avoid fine-tunings in the initial conditions of the scalar field. We mainly focus on the stability of the resulting solutions, and we also investigate if these solutions are attractors of the cosmological system. We shall calculate the resulting scalar potential and, by using a numerical approach, we examine the stability and attractor properties of the solutions. As we show, the first constant-roll era is dynamically unstable towards linear perturbations, and the cosmological system is driven by the attractor solution to the final constant-roll era. As we demonstrate, it is possible to have a nearly scale-invariant power spectrum of primordial curvature perturbations in some cases; however, this is strongly model dependent and depends on the rate of the final constant-roll era. Finally, we present, in brief, the essential features of a model that allows oscillations between constant-roll eras.

Nanostructured Mg 2Ni materials prepared by cold rolling and used as negative electrode for Ni-MH batteries

NASA Astrophysics Data System (ADS)

Pedneault, Sylvain; Huot, Jacques; Roué, Lionel

In the present work, cold rolling has been investigated as a new means of producing Mg-based metal hydrides for nickel-metal hydride (Ni-MH) batteries. Structure and electrochemical evolution of 2Mg-Ni cold-rolled samples were investigated as a function of the number of rolling passes as well as heat treatment. It was found that nanocrystalline Mg 2Ni alloy can be obtained by an appropriate three step process involving rolling, heat treatment and rolling again. It was shown that the number of primary and secondary rolling passes must be carefully optimized in order to favour the complete formation of Mg 2Ni alloy having a nanocrystalline structure (∼10 nm in crystallite size) without excessive sample oxidation. Actually, the best result was obtained by first rolling 90 times, followed by a heat treatment at 400 °C for 4 h and roll again 20 times. The resulting material displayed an initial discharge capacity of 205 mAh g -1, which is quite similar to that obtained with ball-milled Mg 2Ni alloy.

The bridge technique for pectus bar fixation: a method to make the bar un-rotatable.

PubMed

Park, Hyung Joo; Kim, Kyung Soo; Moon, Young Kyu; Lee, Sungsoo

2015-08-01

Pectus bar rotation is a major challenge in pectus repair. However, to date, no satisfactory technique to completely eliminate bar displacement has been introduced. Here, we propose a bar fixation technique using a bridge that makes the bar unmovable. The purpose of this study was to determine the efficacy of this bridge technique. A total of 80 patients underwent pectus bar repair of pectus excavatum with the bridge technique from July 2013 to July 2014. The technique involved connecting 2 parallel bars using plate-screws at the ends of the bars. To determine bar position change, the angles between the sternum and pectus bars were measured on postoperative day 5 (POD5) and 4 months (POM4) and compared. The mean patient age was 17.5 years (range, 6-38 years). The mean difference between POD5 and POM4 were 0.23° (P=.602) and 0.35° (P=.338) for the upper and lower bars, respectively. Bar position was virtually unchanged during the follow-up, and there was no bar dislocation or reoperation. A "bridge technique" designed to connect 2 parallel bars using plates and screws was demonstrated as a method to avoid pectus bar displacement. This approach was easy to implement without using sutures or invasive devices. Copyright © 2015 Elsevier Inc. All rights reserved.

Enabling Narrow(est) IWA Coronagraphy with STIS BAR5 and BAR10 Occulters

NASA Astrophysics Data System (ADS)

Schneider, Glenn; Gaspar, Andras; Debes, John; Gull, Theodore; Hines, Dean; Apai, Daniel; Rieke, George

2017-09-01

The Space Telescope Imaging Spectrograph's (STIS) BAR5 coronagraphic occulter was designed to provide high-contrast, visible-light, imaging in close (> 0.15") angular proximity to bright point-sources. We explored and verified the functionality and utility of the BAR5 occulter. We also investigated, and herein report on, the use of the BAR10 rounded corners as narrow-angle occulters and compare IWA vs. contrast performance for the BAR5, BAR10, and Wedge occulters. With that, we provide recommendations for the most efficacious BAR5 and BAR10 use on-orbit in support of GO science.

Measurement of Cosmic-Ray Antiproton Spectrum at Solar Minimum with a Long-Duration Balloon Flight in Antarctica

NASA Technical Reports Server (NTRS)

Abe, K.; Fuke, H.; Haino, S.; Hams, T.; Hasegawa, M.; Horikoshi, A.; Kim, K. C.; Kusumoto, A.; Lee, M. H.; Makida, Y.;

$X(3873$ and $Y(4140)$ using diquark-antidiquark operators with lattice QCD

DOE PAGES

Padmanath, M.; Lang, C.  B.; Prelovsek Komelj, Sasa

2015-08-01

We perform a lattice study of charmonium-like mesons withmore » $$J^{PC}=1^{++}$$ and three quark contents $$\\bar cc \\bar du$$, $$\\bar cc(\\bar uu+\\bar dd)$$ and $$\\bar cc \\bar ss$$, where the later two can mix with $$\\bar cc$$. This simulation with $$N_f=2$$ and $$m_\\pi=266$$ MeV aims at the possible signatures of four-quark exotic states. We utilize a large basis of $$\\bar cc$$, two-meson and diquark-antidiquark interpolating fields, with diquarks in both anti-triplet and sextet color representations. A lattice candidate for X(3872) with I=0 is observed very close to the experimental state only if both $$\\bar cc$$ and $$D\\bar D^*$$ interpolators are included; the candidate is not found if diquark-antidiquark and $$D\\bar D^*$$ are used in the absence of $$\\bar cc$$. No candidate for neutral or charged X(3872), or any other exotic candidates are found in the I=1 channel. We also do not find signatures of exotic $$\\bar cc\\bar ss$$ candidates below 4.3 GeV, such as Y(4140). Possible physics and methodology related reasons for that are discussed. Along the way, we present the diquark-antidiquark operators as linear combinations of the two-meson operators via the Fierz transformations.« less

Dynamics of 30 large channel bars in the Lower Mississippi River in response to river engineering from 1985 to 2015

NASA Astrophysics Data System (ADS)

Wang, Bo; Xu, Y. Jun

2018-01-01

Channel bars are a major depositional feature in alluvial rivers and their morphodynamics has been investigated intensively in the past several decades. However, relatively less is known about how channel bars in alluvial rivers respond to river engineering and regulations. In this study, we assessed 30-yr morphologic changes of 30 large emerged bars located in a 223 km reach of the highly regulated Lower Mississippi River from Vicksburg, Mississippi, to the Mississippi-Atchafalaya River diversion. Landsat imagery and river stage data between 1985 and 2015 were utilized to characterize bar morphologic features and quantify decadal changes. Based on bar surface areas estimated with the satellite images at different river stages, a rating curve was developed for each of the 30 bars to determine their volumes. Results from this study show that the highly regulated river reach favored the growth of mid-channel and attached bars, while more than half of the point bars showed degradation. Currently, the mid-channel and attached bars accounted for 38% and 34% of the total volume of the 30 bars. The average volume of a single mid-channel bar is over two times that of an attached bar and over four times that of a point bar. Overall, in the past three decades, the total volume of the studied 30 bars increased by 110,118,000 m3 (41%). Total dike length in a dike field was found mostly contributing to the bar volume increase. Currently, the emerged volume of the 30 bars was estimated approximately 378,183,000 m3. The total bar volume is equivalent to 530 million metric tons of coarse sand, based on an average measured bulk density of 1.4 t/m3 for the bar sediment. The findings show that these bars are large sediment reservoirs.

40 CFR 467.21 - Specialized definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... AND STANDARDS ALUMINUM FORMING POINT SOURCE CATEGORY Rolling With Emulsions Subcategory § 467.21 Specialized definitions. For the purpose of this subpart: (a) The “core” of the rolling with emulsions subcategory shall include rolling using emulsions, roll grinding, stationary casting, homogenizing, artificial...

75 FR 50877 - Airworthiness Directives; Rolls-Royce plc RB211-524C2 Series Turbofan Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-18

... Airworthiness Directives; Rolls-Royce plc RB211-524C2 Series Turbofan Engines AGENCY: Federal Aviation.... The FAA amends Sec. 39.13 by adding the following new AD: 2010-17-13 Rolls-Royce plc (Formerly Rolls...) None. Applicability (c) This AD applies to Rolls-Royce plc (RR) model RB211-524C2-19 and RB211-524C2-B...

Development of a Dirigible Bomb

DTIC Science & Technology

1943-04-15

X - ¥ control for all future high-angle dirigible bombs in spite of the instrumental complications involved. /. two gyro system consisting of t...ts found thet the bomb wos in roll equilibrium £.t aero roll orientetion . Moreover, these roll equilibrium positions ire stt-ble ss indicated by...tirflow giving rise to voll torques in the seme direction fcs roll dis- placements from the «ero orientetion , the roll equilibrium found for equel pitch

A Review of Texture Evolution Mechanisms During Deformation by Rolling in Aluminum Alloys

NASA Astrophysics Data System (ADS)

Li, Shasha; Zhao, Qi; Liu, Zhiyi; Li, Fudong

2018-06-01

The current understanding of texture evolution during deformation by rolling in aluminum alloys was summarized. This included understanding the evolution mechanisms and several key factors of initial texture, microstructure, alloy composition, deformation temperature, stress-strain condition, and rolling geometry. Related models on predicting texture evolution during rolling were also discussed. Finally, for this research field, the recommendations for controlling the formation of rolling textures were proposed.

Advances in roll to roll processing of optics

NASA Astrophysics Data System (ADS)

Watts, Michael P. C.

2008-02-01

Today, there are a number of successful commercial applications that utilize roll to roll processing and almost all involve optics; unpatterned film, patterned film, and devices on film. The largest applications today are in holograms, and brightness enhancement film (BEF) for LCD. Solar cells are rapidly growing. These are mostly made in large captive facilities with their own proprietary equipment, materials and pattern generation capability. World wide roll to roll volume is > 100M meters2 year -1, and generates sales of > $5B. The vast majority of the sales are in BEF film by 3M.

Constant-roll tachyon inflation and observational constraints

NASA Astrophysics Data System (ADS)

Gao, Qing; Gong, Yungui; Fei, Qin

2018-05-01

For the constant-roll tachyon inflation, we derive the analytical expressions for the scalar and tensor power spectra, the scalar and tensor spectral tilts and the tensor to scalar ratio to the first order of epsilon1 by using the method of Bessel function approximation. The derived ns-r results are compared with the observations, we find that only the constant-roll inflation with ηH being a constant is consistent with the observations and observations constrain the constant-roll inflation to be slow-roll inflation. The tachyon potential is also reconstructed for the constant-roll inflation which is consistent with the observations.

Control law parameterization for an aeroelastic wind-tunnel model equipped with an active roll control system and comparison with experiment

NASA Technical Reports Server (NTRS)

Perry, Boyd, III; Dunn, H. J.; Sandford, Maynard C.

1988-01-01

Nominal roll control laws were designed, implemented, and tested on an aeroelastically-scaled free-to-roll wind-tunnel model of an advanced fighter configuration. The tests were performed in the NASA Langley Transonic Dynamics Tunnel. A parametric study of the nominal roll control system was conducted. This parametric study determined possible control system gain variations which yielded identical closed-loop stability (roll mode pole location) and identical roll response but different maximum control-surface deflections. Comparison of analytical predictions with wind-tunnel results was generally very good.

An advanced dissymmetric rolling model for online regulation

NASA Astrophysics Data System (ADS)

Cao, Trong-Son

2017-10-01

Roll-bite model is employed to predict the rolling force, torque as well as to estimate the forward slip for preset or online regulation at industrial rolling mills. The rolling process is often dissymmetric in terms of work-rolls rotation speeds and diameters as well as the friction conditions at upper and lower contact surfaces between work-rolls and the strip. The roll-bite model thus must be able to account for these dissymmetries and in the same time has to be accurate and fast enough for online applications. In the present study, a new method, namely Adapted Discretization Slab Method (ADSM) is proposed to obtain a robust roll-bite model, which can take into account the aforementioned dissymmetries and has a very short response time, lower than one millisecond. This model is based on the slab method, with an adaptive discretization and a global Newton-Raphson procedure to improve the convergence speed. The model was validated by comparing with other dissymmetric models proposed in the literature, as well as Finite Element simulations and industrial pilot trials. Furthermore, back-calculation tool was also constructed for friction management for both offline and online applications. With very short CPU time, the ADSM-based model is thus attractive for all online applications, both for cold and hot rolling.

Roll compaction/dry granulation: comparison between roll mill and oscillating granulator in dry granulation.

PubMed

Sakwanichol, Jarunee; Puttipipatkhachorn, Satit; Ingenerf, Gernot; Kleinebudde, Peter

2012-01-01

Different experimental factorial designs were employed to evaluate granule properties obtained from oscillating granulator and roll mill. Four oscillating-granulator parameters were varied, i.e. rotor speed, oscillating angle, aperture of mesh screen and rotor type. Six roll-mill parameters that were throughput, speed ratio in both first and second stages, gap between roll pair in both stages and roll-surface texture were also investigated. Afterwards, the granule properties obtained from two milling types with similar median particle size were compared. All milling parameters in both milling types affected significantly the median particle size, size distribution and amount of fine particles (P < 0.05), except the rotor types of oscillating granulator on fines. Only three milling parameters influenced significantly the flowability (P < 0.05). These were the throughput and the gap size in the first stage of roll mill and the sieve size of oscillating granulator. In comparison between milling types, the differences of granule properties were not practically relevant. However, the roll mill had much higher capacity than the oscillating granulator about seven times, resulting in improving energy savings per unit of product. Consequently, the roll mill can be applied instead of oscillating granulator for roll compaction/dry granulation technique.

The Effects of Forming Parameters on Conical Ring Rolling Process

PubMed Central

Meng, Wen; Zhao, Guoqun; Guan, Yanjin

2014-01-01

The plastic penetration condition and biting-in condition of a radial conical ring rolling process with a closed die structure on the top and bottom of driven roll, simplified as RCRRCDS, were established. The reasonable value range of mandrel feed rate in rolling process was deduced. A coupled thermomechanical 3D FE model of RCRRCDS process was established. The changing laws of equivalent plastic strain (PEEQ) and temperature distributions with rolling time were investigated. The effects of ring's outer radius growth rate and rolls sizes on the uniformities of PEEQ and temperature distributions, average rolling force, and average rolling moment were studied. The results indicate that the PEEQ at the inner layer and outer layer of rolled ring are larger than that at the middle layer of ring; the temperatures at the “obtuse angle zone” of ring's cross-section are higher than those at “acute angle zone”; the temperature at the central part of ring is higher than that at the middle part of ring's outer surfaces. As the ring's outer radius growth rate increases at its reasonable value ranges, the uniformities of PEEQ and temperature distributions increase. Finally, the optimal values of the ring's outer radius growth rate and rolls sizes were obtained. PMID:25202716

Experimental determination of heat transfer coefficients in roll bite and air cooling for computer simulations of 1100 MPa carbon steel rolling

NASA Astrophysics Data System (ADS)

Leinonen, Olli; Ilmola, Joonas; Seppälä, Oskari; Pohjonen, Aarne; Paavola, Jussi; Koskenniska, Sami; Larkiola, Jari

2018-05-01

In modeling of hot rolling pass schedules the heat transfer phenomena have to be known. Radiation to ambient, between rolls and a steel slab as well as heat transfer in contacts must be considered to achieve accurate temperature distribution and thereby accurate material behavior in simulations. Additional heat is generated by friction between the slab and the work roll and by plastic deformation. These phenomena must be taken into account when the effective heat transfer coefficient is determined from experimental data. In this paper we determine the effective heat transfer coefficient at the contact interface and emissivity factor of slab surface for 1100MPa strength carbon steel for hot rolling simulations. Experimental pilot rolling test were carried out and slab temperatures gathered right below the interface and at the mid thickness of the slab. Emissivity factor tests were carried out in the same manner but without rolling. Experimental data is utilized to derive contact heat transfer coefficient at the interface and emissivity factor of slab surface. Pilot rolling test is reproduced in FE-analysis to further refine the heat transfer coefficient and emissivity factor. Material mechanical properties at rolling temperatures were determined by Gleeble™ thermo-mechanical simulator and IDS thermodynamic-kinetic-empirical software.

Measurement of the forward-backward asymmetry of $$\\Lambda$$ and $$\\bar{\\Lambda}$$ production in $$p \\bar{p}$$ collisions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abazov, Victor Mukhamedovich

Here, we studymore » $$\\Lambda$$ and $$\\bar{\\Lambda}$$ production asymmetries in $$p \\bar{p} \\rightarrow \\Lambda (\\bar{\\Lambda}) X$$, $$p \\bar{p} \\rightarrow J/\\psi \\Lambda (\\bar{\\Lambda}) X$$, and $$p \\bar{p} \\rightarrow \\mu^\\pm \\Lambda (\\bar{\\Lambda}) X$$ events recorded by the D0 detector at the Fermilab Tevatron collider at $$\\sqrt{s} = 1.96$$ TeV. We find an excess of $$\\Lambda$$'s ($$\\bar{\\Lambda}$$'s) produced in the proton (antiproton) direction. This forward-backward asymmetry is measured as a function of rapidity. We confirm that the $$\\bar{\\Lambda}/\\Lambda$$ production ratio, measured by several experiments with various targets and a wide range of energies, is a universal function of "rapidity loss", i.e., the rapidity difference of the beam proton and the lambda.« less

Measurement of the forward-backward asymmetry of $$\\Lambda$$ and $$\\bar{\\Lambda}$$ production in $$p \\bar{p}$$ collisions

DOE PAGES

Abazov, Victor Mukhamedovich

2016-02-09

Here, we studymore » $$\\Lambda$$ and $$\\bar{\\Lambda}$$ production asymmetries in $$p \\bar{p} \\rightarrow \\Lambda (\\bar{\\Lambda}) X$$, $$p \\bar{p} \\rightarrow J/\\psi \\Lambda (\\bar{\\Lambda}) X$$, and $$p \\bar{p} \\rightarrow \\mu^\\pm \\Lambda (\\bar{\\Lambda}) X$$ events recorded by the D0 detector at the Fermilab Tevatron collider at $$\\sqrt{s} = 1.96$$ TeV. We find an excess of $$\\Lambda$$'s ($$\\bar{\\Lambda}$$'s) produced in the proton (antiproton) direction. This forward-backward asymmetry is measured as a function of rapidity. We confirm that the $$\\bar{\\Lambda}/\\Lambda$$ production ratio, measured by several experiments with various targets and a wide range of energies, is a universal function of "rapidity loss", i.e., the rapidity difference of the beam proton and the lambda.« less

State-to-state rotationally inelastic scattering of ND[sub 3] on a graphite (0001) surface

DOE Office of Scientific and Technical Information (OSTI.GOV)

LaVilla, M.E.; Ionova, I.V.; Ionov, S.I.

1992-12-15

State-selected molecular beams of deuterated ammonia, [vert bar][ital JKM][epsilon][gt][vert bar]inversion[gt]=[vert bar]1111[gt][vert bar][minus][gt] or [vert bar]222[minus]1[gt][vert bar][minus][gt] and [vert bar]3331[gt][vert bar][minus][gt] states in the proportion 2.3:1, are produced via hexapole electrostatic focusing and then scattered at near-normal incidence on a graphite (0001) surface at [ital T][sub [ital s

Micro-mechanisms of Surface Defects Induced on Aluminum Alloys during Plastic Deformation at Elevated Temperatures

NASA Astrophysics Data System (ADS)

Gali, Olufisayo A.

Near-surface deformed layers developed on aluminum alloys significantly influence the corrosion and tribological behavior as well as reduce the surface quality of the rolled aluminum. The evolution of the near-surface microstructures induced on magnesium containing aluminum alloys during thermomechanical processing has been investigated with the aim generating an understanding of the influence of individual forming parameters on its evolution and examine the microstructure of the roll coating induced on the mating steel roll through material transfer during rolling. The micro-mechanisms related to the various features of near-surface microstructure developed during tribological conditions of the simulated hot rolling process were identified. Thermomechanical processing experiments were performed with the aid of hot rolling (operating temperature: 550 to 460 °C, 4, 10 and 20 rolling pass schedules) and hot forming (operating temperature: 350 to 545 °C, strain rate: 4 x 10-2 s-1) tribo-simulators. The surface, near-surface features and material transfer induced during the elevated temperature plastic deformation were examined and characterized employing optical interferometry, SEM/EDS, FIB and TEM. Near-surface features characterized on the rolled aluminum alloys included; cracks, fractured intermetallic particles, aluminum nano-particles, oxide decorated grain boundaries, rolled-in oxides, shingles and blisters. These features were related to various individual rolling parameters which included, the work roll roughness, which induced the formation of shingles, rolling marks and were responsible for the redistribution of surface oxide and the enhancements of the depth of the near-surface damage. The enhanced stresses and strains experienced during rolling were related to the formation and propagation of cracks, the nanocrystalline structure of the near-surface layers and aluminum nano-particles. The mechanism of the evolution of the near-surface microstructure were determined to include grain boundary sliding which induced the cracks at the surface and subsurface of the alloy, magnesium diffusion to free surfaces, crack propagation from shear stresses and the shear strains inducing the nanocrystalline grain structure, the formation of shingles by the shear deformation of micro-wedges induced by the work roll grooves, and the deformation of this oxide covered micro-wedges inducing the rolled-in oxides. Magnesium diffusion to free surfaces was identified as inducing crack healing due to the formation of MgO within cracks and was responsible for the oxide decorated grain boundaries. An examination of the roll coating revealed a complex layered microstructure that was induced through tribo-chemical and mechanical entrapment mechanisms. The microstructure of the roll coating suggested that the work roll material and the rolled aluminum alloy were essential in determining its composition and structure. Subsequent hot forming processes revealed the rich oxide-layer of the near-surface microstructure was beneficial for reducing the coefficient of friction during tribological contact with the steel die. Damage to the microstructure include cracks induced from grain boundary sliding of near-surface grains and the formation of oxide fibres within cracks of the near-surface deformed layers.

Membrane-sculpting BAR domains generate stable lipid microdomains.

PubMed

Zhao, Hongxia; Michelot, Alphée; Koskela, Essi V; Tkach, Vadym; Stamou, Dimitrios; Drubin, David G; Lappalainen, Pekka

2013-09-26

Bin-Amphiphysin-Rvs (BAR) domain proteins are central regulators of many cellular processes involving membrane dynamics. BAR domains sculpt phosphoinositide-rich membranes to generate membrane protrusions or invaginations. Here, we report that, in addition to regulating membrane geometry, BAR domains can generate extremely stable lipid microdomains by "freezing" phosphoinositide dynamics. This is a general feature of BAR domains, because the yeast endocytic BAR and Fes/CIP4 homology BAR (F-BAR) domains, the inverse BAR domain of Pinkbar, and the eisosomal BAR protein Lsp1 induced phosphoinositide clustering and halted lipid diffusion, despite differences in mechanisms of membrane interactions. Lsp1 displays comparable low diffusion rates in vitro and in vivo, suggesting that BAR domain proteins also generate stable phosphoinositide microdomains in cells. These results uncover a conserved role for BAR superfamily proteins in regulating lipid dynamics within membranes. Stable microdomains induced by BAR domain scaffolds and specific lipids can generate phase boundaries and diffusion barriers, which may have profound impacts on diverse cellular processes. Copyright © 2013 The Authors. Published by Elsevier Inc. All rights reserved.

Valuation of coefficient of rolling friction by the inclined plane method

NASA Astrophysics Data System (ADS)

Ciornei, F. C.; Alaci, S.; Ciogole, V. I.; Ciornei, M. C.

2017-05-01

A major objective of tribological researches is characterisation of rolling friction, due to various cases encountered in classical engineering applications, like gear transmissions and cam mechanisms or more recent examples met in bioengineering and biomedical devices. A characteristic of these examples consists in reduced dimensions of the contact zones, theoretically zero, the relative motion occurring between the contact points being either sliding or rolling. A characteristic parameter for the rolling motion is the coefficient of rolling friction. The paper proposes a method for estimation of coefficient of rolling friction by studying the motion of a body of revolution on an inclined plane. Assuming the hypothesis that moment of rolling friction is proportional to the normal reaction force, the law of motion for the body on the inclined plane is found under the premise of pure rolling. It is reached the conclusion that there is an uniformly accelerated motion, and thus for a known plane slope, it is sufficient to find the time during which the body runs a certain distance, starting from motionless situation. To obtain accurate results assumes finding precisely the time of motion. The coefficient of rolling friction was estimated for several slopes of the inclined plane and it is concluded that with increased slope, the values of coefficient of rolling friction increase, fact that suggest that the proportionality between the rolling torque and normal load is valid only for domains of limited variations of normal load.

40 CFR 426.30 - Applicability; description of the rolled glass manufacturing subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... rolled glass manufacturing subcategory. 426.30 Section 426.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GLASS MANUFACTURING POINT SOURCE CATEGORY Rolled Glass Manufacturing Subcategory § 426.30 Applicability; description of the rolled glass...

40 CFR 426.30 - Applicability; description of the rolled glass manufacturing subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... rolled glass manufacturing subcategory. 426.30 Section 426.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GLASS MANUFACTURING POINT SOURCE CATEGORY Rolled Glass Manufacturing Subcategory § 426.30 Applicability; description of the rolled glass...

Interaction of real and virtual p p bar pairs in J / ψ → p p bar γ (ρ , ω) decays

NASA Astrophysics Data System (ADS)

Milstein, A. I.; Salnikov, S. G.

2017-10-01

The p p bar invariant mass spectra of the processes J / ψ → p p bar ω, J / ψ → p p bar ρ, and J / ψ → p p bar γ close to the p p bar threshold are calculated by means of the N N bar optical potential. The potential model for N N bar interaction in the S10 state is proposed. The parameters of the model are obtained by fitting the cross section of N N bar scattering together with the p p bar invariant mass spectra of the J / ψ decays. Good agreement with the available experimental data is achieved. Using our potential and the Green's function approach we also describe the peak in the η‧π+π- invariant mass spectrum in the decay J / ψ → γη‧π+π- in the energy region near the N N bar threshold.

Genderedness of bar drinking culture and alcohol-related harms: A multi-country study

PubMed Central

Roberts, Sarah C. M.; Bond, Jason; Korcha, Rachael; Greenfield, Thomas K.

2012-01-01

This study explores whether associations between consuming alcohol in bars and alcohol-related harms are consistent across countries and whether country-level characteristics modify associations. We hypothesized that genderedness of bar drinking modifies associations, such that odds of harms associated with bar drinking increase more rapidly in predominantly male bar-drinking countries. Multilevel analysis was used to analyze survey data from 21 countries representing five continents from Gender, Alcohol, and Culture: An International Study (GENACIS). Bar frequency was positively associated with harms overall. Relationships between bar frequency and harms varied across country. Genderedness modified associations between bar frequency and odds of fights, marriage/relationship harms, and work harms. Findings were significant only for men. Contrary to our hypothesis, odds of harms associated with bar drinking increased less rapidly in countries where bar drinking is predominantly male. This suggests predominantly male bar drinking cultures may be protective for males who more frequently drink in bars. PMID:23710158

Spread prediction model of continuous steel tube based on BP neural network

NASA Astrophysics Data System (ADS)

Zhai, Jian-wei; Yu, Hui; Zou, Hai-bei; Wang, San-zhong; Liu, Li-gang

2017-07-01

According to the geometric pass of roll and technological parameters of three-roller continuous mandrel rolling mill in a factory, a finite element model is established to simulate the continuous rolling process of seamless steel tube, and the reliability of finite element model is verified by comparing with the simulation results and actual results of rolling force, wall thickness and outer diameter of the tube. The effect of roller reduction, roller rotation speed and blooming temperature on the spread rule is studied. Based on BP(Back Propagation) neural network technology, a spread prediction model of continuous rolling tube is established for training wall thickness coefficient and spread coefficient of the continuous rolling tube, and the rapid and accurate prediction of continuous rolling tube size is realized.

Effect of Cold-rolling on Mechanical Properties and Microstructure of an Al-12%Si-0.2%Mg Alloy

NASA Astrophysics Data System (ADS)

Liao, Hengcheng; Cai, Mingdong; Jing, Qiumin; Ding, Ke

2011-11-01

Effect of multi-pass cold-rolling on the mechanical properties and microstructure of a near-eutectic Al-12%Si-0.2%Mg casting alloy was investigated. Optical microscopy, SEM, and TEM were employed to resolve the as-rolled microstructure, and the microstructure of samples after aging treatment. It has been found that Brinell hardness increases considerably with rolling reduction ratio; and further annealing leads to a remarkable drop in hardness. Two mechanisms, namely precipitation hardening and recovery softening, were found to develop simultaneously in the subsequent aging treatment following cold rolling. In contrast, recovery softening dominated the aging of cold-rolled specimen with prior intermediate annealing. Tensile properties were also performed to measure the effect of cold rolling and subsequent aging treatment.

Research on the rolling moment in the symmetrical and asymmetrical rolling process

NASA Astrophysics Data System (ADS)

Alexa, V.; Raţiu, S. A.; Kiss, I.; Cioată, C. G.

2017-01-01

Research distribution the rolling moments symmetrical and asymmetrical report presents great importance both in theory and to introduce clarifications to the calculation of rolling resistance line assemblies. Clarifying individuals of metallic material deformation between the rolls single cylinder diameters act of any difference of work and analysis of advance and delay phenomena. Torque drive value for each of the rolling cylinders was done by reducing the thickness of the laminate samples, an experimental facility located in the laboratory of plastic deformation of the Faculty of Engineering Hunedoara. The analysis of research results show that in terms of power consumption for deformation and safety equipment in operation is rational for mills which require such a difference between the work rolls to execute about one cylinder operated.

The theory and technique of yamuna body rolling.

PubMed

Suzuki, Satoshi

2013-09-01

[Purpose] This paper provides information about the theory and technique of Yamuna Body Rolling. In order to treat physical problems, using the specialized Yamuna Body Rolling balls, people can target superficial skin, fasciae, muscle fibers, tendons, ligaments, bones, internal organs, and the nervous system by themselves. The extraordinary effect of Yamuna Body Rolling is its multidimensional elongation of muscle fibers. In addition to the regular longitudinal elongation by the conventional stretch method, Yamuna Body Rolling enables the transversal and diagonal expansion of muscle fibers in order to move the body more dynamically. Hamstring, abdominal, and sideline routines are presented as examples for techniques of Yamuna Body Rolling. Yamuna Body Rolling can be applied to functional evaluation and therapeutic uses; therefore, it could provide many benefits in the treatment of different conditions in the medical field.

Slow-roll approximation in loop quantum cosmology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Luc, Joanna; Mielczarek, Jakub, E-mail: joanna.luc@uj.edu.pl, E-mail: jakub.mielczarek@uj.edu.pl

The slow-roll approximation is an analytical approach to study dynamical properties of the inflationary universe. In this article, systematic construction of the slow-roll expansion for effective loop quantum cosmology is presented. The analysis is performed up to the fourth order in both slow-roll parameters and the parameter controlling the strength of deviation from the classical case. The expansion is performed for three types of the slow-roll parameters: Hubble slow-roll parameters, Hubble flow parameters and potential slow-roll parameters. An accuracy of the approximation is verified by comparison with the numerical phase space trajectories for the case with a massive potential term.more » The results obtained in this article may be helpful in the search for the subtle quantum gravitational effects with use of the cosmological data.« less

SEMI-ROLLED LEAF1 Encodes a Putative Glycosylphosphatidylinositol-Anchored Protein and Modulates Rice Leaf Rolling by Regulating the Formation of Bulliform Cells1[W][OA

PubMed Central

Xiang, Jing-Jing; Zhang, Guang-Heng; Qian, Qian; Xue, Hong-Wei

2012-01-01

Leaf rolling is an important agronomic trait in rice (Oryza sativa) breeding and moderate leaf rolling maintains the erectness of leaves and minimizes shadowing between leaves, leading to improved photosynthetic efficiency and grain yields. Although a few rolled-leaf mutants have been identified and some genes controlling leaf rolling have been isolated, the molecular mechanisms of leaf rolling still need to be elucidated. Here we report the isolation and characterization of SEMI-ROLLED LEAF1 (SRL1), a gene involved in the regulation of leaf rolling. Mutants srl1-1 (point mutation) and srl1-2 (transferred DNA insertion) exhibit adaxially rolled leaves due to the increased numbers of bulliform cells at the adaxial cell layers, which could be rescued by complementary expression of SRL1. SRL1 is expressed in various tissues and is expressed at low levels in bulliform cells. SRL1 protein is located at the plasma membrane and predicted to be a putative glycosylphosphatidylinositol-anchored protein. Moreover, analysis of the gene expression profile of cells that will become epidermal cells in wild type but probably bulliform cells in srl1-1 by laser-captured microdissection revealed that the expression of genes encoding vacuolar H+-ATPase (subunits A, B, C, and D) and H+-pyrophosphatase, which are increased during the formation of bulliform cells, were up-regulated in srl1-1. These results provide the transcript profile of rice leaf cells that will become bulliform cells and demonstrate that SRL1 regulates leaf rolling through inhibiting the formation of bulliform cells by negatively regulating the expression of genes encoding vacuolar H+-ATPase subunits and H+-pyrophosphatase, which will help to understand the mechanism regulating leaf rolling. PMID:22715111

Microstructure and texture evolution in cold-rolled and annealed alloy MA-956

NASA Astrophysics Data System (ADS)

Hosoda, Takashi

The microstructural and texture development with thermomechanical processing, performed through a combination of cold-rolling and annealing, in MA-956 plate consisting of a layered and inhomogeneous microstructure was systematically assessed. The alloy contained in mass percent, 20 Cr, 4.8 Al, 0.4 Ti, 0.4 Y2O3, and the balance iron. The starting material was as-hot-rolled plate, 9.7 mm thick. The as-hot-rolled plate was subjected to 40%, 60%, and 80% cold-rolling reduction and subsequently annealed at 1000, 1200, or 1380. Assessment of microstructural and texture developments before and after cold-rolling and annealing was performed using light optical microscopy (LOM), Vickers hardness testing, and electron backscatter diffraction (EBSD). Locally introduced misorientations by cold-rolling in each region were evaluated by Kernel Average Misorientation (KAM) maps. The as-hot-rolled condition contained a layered and inhomogeneous microstructure consisting of thin and coarse elongated grains, and aggregated regions which consisted of fine grains and sub-grains with {100} texture parallel to the longitudinal direction. The microstructure of the 40% cold-rolled condition contained deformation bands, and the 60% and 80% cold-rolled conditions also contained highly deformed regions where the deformation bands were intricately tangled. A predominant orientation of (001) parallel to the rolling direction was developed during cold-rolling, becoming more prominent with increasing reduction. The magnitudes of KAM angles varied through the thickness depending on the initial microstructures. Recrystallization occurred in regions where high KAM angles were dense after annealing and nucleation sites were the aggregation regions, deformation bands, and highly deformed regions. The shape and size of the recrystallized grains varied depending on the nucleation sites.

Different functional modes of BAR domain proteins in formation and plasticity of mammalian postsynapses.

PubMed

Kessels, Michael M; Qualmann, Britta

2015-09-01

A plethora of cell biological processes involve modulations of cellular membranes. By using extended lipid-binding interfaces, some proteins have the power to shape membranes by attaching to them. Among such membrane shapers, the superfamily of Bin-Amphiphysin-Rvs (BAR) domain proteins has recently taken center stage. Extensive structural work on BAR domains has revealed a common curved fold that can serve as an extended membrane-binding interface to modulate membrane topologies and has allowed the grouping of the BAR domain superfamily into subfamilies with structurally slightly distinct BAR domain subtypes (N-BAR, BAR, F-BAR and I-BAR). Most BAR superfamily members are expressed in the mammalian nervous system. Neurons are elaborately shaped and highly compartmentalized cells. Therefore, analyses of synapse formation and of postsynaptic reorganization processes (synaptic plasticity) - a basis for learning and memory formation - has unveiled important physiological functions of BAR domain superfamily members. These recent advances, furthermore, have revealed that the functions of BAR domain proteins include different aspects. These functions are influenced by the often complex domain organization of BAR domain proteins. In this Commentary, we review these recent insights and propose to classify BAR domain protein functions into (1) membrane shaping, (2) physical integration, (3) action through signaling components, and (4) suppression of other BAR domain functions. © 2015. Published by The Company of Biologists Ltd.

Deposition model of a Miocene barred wave- and storm-dominated shoreface and shelf, southeastern Malay basin, offshore west Malaysia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ramli, N.

1986-01-01

The J sandstone is an important hydrocarbon-bearing reservoir in the southeastern part of the Malay basin. The lower and upper members of the J sandstone are composed of shoreface and offshore sediments. The shoreface sequence contains depositional structures characteristic of a barred wave- and storm-dominated shoreface. Each shoreface sequence is laterally associated with a series of stacked offshore bars. Offshore bars can be subdivided into proximal and distal types. Two types of proximal offshore bars have been identified: (1) proximal bars formed largely above fair-weather wave base (inner proximal bars), and (2) proximal bars formed below fair-weather wave base (outermore » proximal bars). The inner proximal bars are closely associated with the shoreface sequence and are similar to the middle and lower shoreface. The presence of poorly sorted, polymodal, very fine to very coarse-grained sandstone beneath well-sorted crestal sandstones of inner proximal bars suggests that these offshore bars may have been deposited rapidly by storms. The crests of the inner proximal offshore bars were subsequently reworked by fair-weather processes, and the crests of the outer proximal and distal offshore bars were reworked by waning storm currents and oscillatory waves. Thick marine shales overlying offshore bars contain isolated sheet sandstones. Each sheet sandstone exhibits features that may be characteristic of distal storm shelf deposits. 15 figures, 2 tables.« less

Effect of roll-compaction and milling conditions on granules and tablet properties.

PubMed

Perez-Gandarillas, Lucia; Perez-Gago, Ana; Mazor, Alon; Kleinebudde, Peter; Lecoq, Olivier; Michrafy, Abderrahim

2016-09-01

Dry granulation is an agglomeration process used to produce size-enlarged particles (granules), improving the handling properties of powders such as flowability. In this process, powders are compacted using a roll press to produce ribbons, which are milled in granules used further in the tableting process. The granule and tablet properties are influenced by the existence of different designs of the roll compactors, milling systems and the interaction between process parameters and raw material properties. The main objective of this work was to investigate how different roll-compaction conditions and milling process parameters impact on ribbons, granules and tablet properties, highlighting the role of the sealing system (cheek plates and rimmed roll). In this context, two common excipients differing in their mechanical behaviour (MCC and mannitol) are used. The study is based on the analysis of granule size distribution together with the characterization of loss of compactability during die compaction. Results show that the tensile strength of tablets is lower when using granules than when the raw materials are compressed. Moreover, the plastic material (MCC) is more sensitive than the brittle one (mannitol). Regarding the roll-force, it is observed that the higher the roll force, the lower the tensile strength of tablets from granulated material is. These findings are in agreement with the literature. The comparison of sealing systems shows that the rimmed-roll system leads to slightly stronger tablets than the use of cheek plates. In addition, the use of the rimmed-roll system reduces the amount of fines, in particular when high roll force is applied. Overall, it can be concluded that roll-compaction effect is predominant over the milling effect on the production of fines but less significant on the tablet properties. This study points out that the balance between a good flowability by reducing the amount of fines and appropriate tablet strength is achieved with rimmed-roll and the highest roll-force used. Copyright © 2016 Elsevier B.V. All rights reserved.

Phase transformation kinetics in rolled U-10 wt. % Mo foil: Effect of post-rolling heat treatment and prior γ-UMo grain size

DOE PAGES

Jana, Saumyadeep; Overman, Nicole; Varga, Tamas; ...

2017-09-25

Here, the effect of sub-eutectoid heat treatment on the phase transformation behavior in rolled U-10 wt.% Mo (U10Mo) foils was systematically investigated. The as-cast 5 mm thick foils were initially homogenized at 900 °C for 48 h and were hot rolled to 2 mm and later cold rolled down to 0.2 mm. Three starting microstructures were evaluated: (i) hot + cold-rolled to 0.2 mm (as-rolled condition), (ii) hot + cold-rolled to 0.2 mm + annealed at 700 °C for 1 h, and (iii) hot + cold-rolled to 0.2 mm + annealed at 1000 °C for 60 h. Annealing of as-rolledmore » materials at 700 °C resulted in small grain size (15 ± 9 μm average grain size), while annealing at 1000 °C led to very large grains (156 ± 118 μm average grain size) in rolled U10Mo foils. Later the samples were subjected to sub-eutectoid heat-treatment temperatures of 550 °C, 500 °C, and 400 °C for different durations of time starting from 1 h up to 100 h. U10Mo rolled foils went through various degrees of decomposition when subjected to the sub-eutectoid heat-treatment step and formed a lamellar microstructure through a cellular reaction mostly along the previous γ-UMo grain boundaries. The least amount of cellular reaction was observed in the large-grain microstructure at all temperatures. Conversely, a substantial amount of cellular reaction was observed in both the as-rolled and the small-grain microstructure. After 100 h of heat treatment at 500 °C, the volume fraction of the lamellar phase was found to be 4%, 22%, and 82% in large-grain, as-rolled, and small-grain samples, respectively.« less

Phase transformation kinetics in rolled U-10 wt. % Mo foil: Effect of post-rolling heat treatment and prior γ-UMo grain size

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jana, Saumyadeep; Overman, Nicole; Varga, Tamas

Here, the effect of sub-eutectoid heat treatment on the phase transformation behavior in rolled U-10 wt.% Mo (U10Mo) foils was systematically investigated. The as-cast 5 mm thick foils were initially homogenized at 900 °C for 48 h and were hot rolled to 2 mm and later cold rolled down to 0.2 mm. Three starting microstructures were evaluated: (i) hot + cold-rolled to 0.2 mm (as-rolled condition), (ii) hot + cold-rolled to 0.2 mm + annealed at 700 °C for 1 h, and (iii) hot + cold-rolled to 0.2 mm + annealed at 1000 °C for 60 h. Annealing of as-rolledmore » materials at 700 °C resulted in small grain size (15 ± 9 μm average grain size), while annealing at 1000 °C led to very large grains (156 ± 118 μm average grain size) in rolled U10Mo foils. Later the samples were subjected to sub-eutectoid heat-treatment temperatures of 550 °C, 500 °C, and 400 °C for different durations of time starting from 1 h up to 100 h. U10Mo rolled foils went through various degrees of decomposition when subjected to the sub-eutectoid heat-treatment step and formed a lamellar microstructure through a cellular reaction mostly along the previous γ-UMo grain boundaries. The least amount of cellular reaction was observed in the large-grain microstructure at all temperatures. Conversely, a substantial amount of cellular reaction was observed in both the as-rolled and the small-grain microstructure. After 100 h of heat treatment at 500 °C, the volume fraction of the lamellar phase was found to be 4%, 22%, and 82% in large-grain, as-rolled, and small-grain samples, respectively.« less

Comparison of vertical hydraulic conductivity in a streambed-point bar system of a gaining stream

NASA Astrophysics Data System (ADS)

Dong, Weihong; Chen, Xunhong; Wang, Zhaowei; Ou, Gengxin; Liu, Can

2012-07-01

SummaryVertical hydraulic conductivities (Kv) of both streambed and point bars can influence water and solute exchange between streams and surrounding groundwater systems. The sediments in point bars are relatively young compared to the older sediments in the adjacent aquifers but slightly older compared to submerged streambeds. Thus, the permeability in point bar sediments can be different not only from regional aquifer but also from modern streambed. However, there is a lack of detailed studies that document spatial variability of vertical hydraulic conductivity in point bars of meandering streams. In this study, the authors proposed an in situ permeameter test method to measure vertical hydraulic conductivity of the two point bars in Clear Creek, Nebraska, USA. We compared the Kv values in streambed and adjacent point bars through 45 test locations in the two point bars and 51 test locations in the streambed. The Kv values in the point bars were lower than those in the streambed. Kruskal-Wallis test confirmed that the Kv values from the point bars and from the channel came from two statistically different populations. Within a point bar, the Kv values were higher along the point bar edges than those from inner point bars. Grain size analysis indicated that slightly more silt and clay particles existed in sediments from inner point bars, compared to that from streambed and from locations near the point bar edges. While point bars are the deposits of the adjacent channel, the comparison of two groups of Kv values suggests that post-depositional processes had an effect on the evolution of Kv from channel to point bars in fluvial deposits. We believed that the transport of fine particles and the gas ebullition in this gaining stream had significant effects on the distribution of Kv values in a streambed-point bar system. With the ageing of deposition in a floodplain, the permeability of point bar sediments can likely decrease due to reduced effects of the upward flow and gas ebullition.

Observation and Study of the Baryonic B-meson Decays B to D(*) p pbar (pi) (pi)

DOE Office of Scientific and Technical Information (OSTI.GOV)

del Amo Sanchez, P.; Lees, J.P.; Poireau, V.

We present results for B-meson decay modes involving a charm meson, protons, and pions using 455 x 10{sup 6} B{bar B} pairs recorded by the BABAR detector at the SLAC PEP-II asymmetric-energy e{sup +}e{sup -} collider. The branching fractions are measured for the following ten decays: {bar B}{sup 0} {yields} D{sup 0}p{bar p}, {bar B}{sup 0} {yields} D*{sup 0}p{bar p}, {bar B}{sup 0} {yields} D{sup +}p{bar p}{pi}{sup -}, {bar B}{sup 0} {yields} D*{sup +}p{bar p}{pi}{sup -}, B{sup -} {yields} D{sup 0}p{bar p}{pi}{sup -}, B{sup -} {yields} D*{sup 0}pp{pi}{sup -}, {bar B}{sup 0} {yields} D{sup 0}p{bar p}{pi}{sup -}{pi}{sup +}, {bar B}{supmore » 0} {yields} D*{sup 0}p{bar p}{pi}{sup -}{pi}{sup +}, B{sup -} {yields} D{sup +}p{bar p}{pi}{sup -}{pi}{sup -}, and B{sup -} {yields} D*{sup +}p{bar p}{pi}{sup -}{pi}{sup -}. The four B{sup -} and the two five-body B{sup 0} modes are observed for the first time. The four-body modes are enhanced compared to the three- and the five-body modes. In the three-body modes, the M(p{bar p}) and M(D{sup (*)0}p) invariant mass distributions show enhancements near threshold values. In the four-body mode {bar B}{sup 0} {yields} D{sup +}p{bar p}{pi}{sup -}, the M(p{pi}{sup -}) distribution shows a narrow structure of unknown origin near 1.5GeV/c{sup 2}. The distributions for the five-body modes, in contrast to the others, are similar to the expectations from uniform phase-space predictions.« less

Roll paper pilot. [mathematical model for predicting pilot rating of aircraft in roll task

NASA Technical Reports Server (NTRS)

Naylor, F. R.; Dillow, J. D.; Hannen, R. A.

1973-01-01

A mathematical model for predicting the pilot rating of an aircraft in a roll task is described. The model includes: (1) the lateral-directional aircraft equations of motion; (2) a stochastic gust model; (3) a pilot model with two free parameters; and (4) a pilot rating expression that is a function of rms roll angle and the pilot lead time constant. The pilot gain and lead time constant are selected to minimize the pilot rating expression. The pilot parameters are then adjusted to provide a 20% stability margin and the adjusted pilot parameters are used to compute a roll paper pilot rating of the aircraft/gust configuration. The roll paper pilot rating was computed for 25 aircraft/gust configurations. A range of actual ratings from 2 to 9 were encountered and the roll paper pilot ratings agree quite well with the actual ratings. In addition there is good correlation between predicted and measured rms roll angle.

Inflation with a constant rate of roll

NASA Astrophysics Data System (ADS)

Motohashi, Hayato; Starobinsky, Alexei A.; Yokoyama, Jun'ichi

2015-09-01

We consider an inflationary scenario where the rate of inflaton roll defined by ̈phi/H dot phi remains constant. The rate of roll is small for slow-roll inflation, while a generic rate of roll leads to the interesting case of 'constant-roll' inflation. We find a general exact solution for the inflaton potential required for such inflaton behaviour. In this model, due to non-slow evolution of background, the would-be decaying mode of linear scalar (curvature) perturbations may not be neglected. It can even grow for some values of the model parameter, while the other mode always remains constant. However, this always occurs for unstable solutions which are not attractors for the given potential. The most interesting particular cases of constant-roll inflation remaining viable with the most recent observational data are quadratic hilltop inflation (with cutoff) and natural inflation (with an additional negative cosmological constant). In these cases even-order slow-roll parameters approach non-negligible constants while the odd ones are asymptotically vanishing in the quasi-de Sitter regime.

Effect of differential speed rolling on the texture evolution of Mg-4Zn-1Gd alloy

NASA Astrophysics Data System (ADS)

Shim, Myeong-Shik; Suh, Byeong-Chan; Kim, Jae H.; Kim, Nack J.

2015-05-01

The microstructural and texture evolution during differential speed rolling process of Mg 4Zn-1Gd (wt%) alloy have been investigated by means of electron backscatter diffraction observation and texture analysis. The angular distribution of basal poles are inclined about 10° from the normal direction towards the rolling direction and the maximum intensities of basal poles are decreased, compared to the conventional rolling process. Such an inclination of angular distribution of basal poles can be induced by the operation of shear stress along the rolling direction, as much as one quarter of tensile stress along the RD and one quarter of compressive stress along the ND. When the reduction ratios in differential speed rolling increase, there is no difference in texture evolution although there is a significant change in activated twinning systems. In addition, the engineering stresses after differential speed rolling are also similar to that after conventional rolling process, while ductility and stretch formability in the former are worse than those in the latter.

Shearlet transform in aliased ground roll attenuation and its comparison with f-k filtering and curvelet transform

NASA Astrophysics Data System (ADS)

Abolfazl Hosseini, Seyed; Javaherian, Abdolrahim; Hassani, Hossien; Torabi, Siyavash; Sadri, Maryam

2015-06-01

Ground roll, which is a Rayleigh surface wave that exists in land seismic data, may mask reflections. Sometimes ground roll is spatially aliased. Attenuation of aliased ground roll is of importance in seismic data processing. Different methods have been developed to attenuate ground roll. The shearlet transform is a directional and multidimensional transform that generates subimages of an input image in different directions and scales. Events with different dips are separated in these subimages. In this study, the shearlet transform is used to attenuate the aliased ground roll. To do this, a shot record is divided into several segments, and the appropriate mute zone is defined for all segments. The shearlet transform is applied to each segment. The subimages related to the non-aliased and aliased ground roll are identified by plotting the energy distributions of subimages with visual checking. Then, muting filters are used on selected subimages. The inverse shearlet transform is applied to the filtered segment. This procedure is repeated for all segments. Finally, all filtered segments are merged using the Hanning window. This method of aliased ground roll attenuation was tested on a synthetic dataset and a field shot record from the west of Iran. The synthetic shot record included strong aliased ground roll, whereas the field shot record did not. To produce the strong aliased ground roll on the field shot record, the data were resampled in the offset direction from 30 to 60 m. To show the performance of the shearlet transform in attenuating the aliased ground roll, we compared the shearlet transform with the f-k filtering and curvelet transform. We showed that the performance of the shearlet transform in the aliased ground roll attenuation is better than that of the f-k filtering and curvelet transform in both the synthetic and field shot records. However, when the dip and frequency content of the aliased ground roll are the same as the reflections, ability of the shearlet transform is limited in attenuating the aliased ground roll.

Bar-spheroid interaction in galaxies

NASA Technical Reports Server (NTRS)

Hernquist, Lars; Weinberg, Martin D.

1992-01-01

N-body simulation and linear analysis is employed to investigate the secular evolution of barred galaxies, with emphasis on the interaction between bars and spheroidal components of galaxies. This interaction is argued to drive secular transfer of angular momentum from bars to spheroids, primarily through resonant coupling. A moderately strong bar, having mass within corotation about 0.3 times the enclosed spheroid mass, is predicted to shed all its angular momentum typically in less than about 10 exp 9 yr. Even shorter depletion time scales are found for relatively more massive bars. It is suggested either that spheroids around barred galaxies are structured so as to inhibit strong coupling with bars, or that bars can form by unknown processes long after disks are established. The present models reinforce the notion that bars can drive secular evolution in galaxies.

Dynamic analysis of four bar planar mechanism extended to six-bar planar mechanism with variable topology

NASA Astrophysics Data System (ADS)

Belleri, Basayya K.; Kerur, Shravankumar B.

2018-04-01

A computer-oriented procedure for solving the dynamic force analysis problem for general planar mechanisms is presented. This paper provides position analysis, velocity analysis, acceleration analysis and force analysis of six bar mechanism with variable topology approach. Six bar mechanism is constructed by joining two simple four bar mechanisms. Initially the position, velocity and acceleration analysis of first four bar mechanism are determined by using the input parameters. The outputs (angular displacement, velocity and acceleration of rocker)of first four bar mechanism are used as input parameter for the second four bar mechanism and the position, velocity, acceleration and forces are analyzed. With out-put parameters of second four-bar mechanism the force analysis of first four-bar mechanism is carried out.

A New Method for Interfacing Unsuited Subjects to Overhead Suspension Partial Gravity Simulators

NASA Technical Reports Server (NTRS)

Norcross, Jason R.; Chappell, Steve; Cowley, Matthew S.; Harvill, Lauren; Gernhardt, Michael L.

2010-01-01

The purpose of performing unsuited testing as part of a reduced gravity extravehicular (EVA) suited human performance research program is to define baseline performance. These results are then coupled with suited test results to evaluate how the suit system affects human performance at reduced gravity. The primary drawback to this approach is that previous studies used notably different systems to interface suited and unsuited subjects to overhead-suspension, partial-gravity simulators. A spreader bar (SB) assembly previously used for unsuited tests allowed limited pitch and roll of the subject, whereas the gimbal for suited tests allowed more pitch and roll, although the mass distribution led to large moments of inertia in the yaw axis. It is hypothesized that use of the same methods for offload of both unsuited and suited subjects is needed to make meaningful comparisons. A new gimbal (GIM) was designed with the idea that it could function with both suited and unsuited subjects. GIM was designed to minimize mass and moments of inertia and to be adjustable to co-locate the 3 axes of rotation with the subject s center of gravity. OBJECTIVE: To evaluate human performance differences between SB and GIM. METHODS: Ten unsuited subjects were off-loaded to 1/6-g using both interfaces. Subjects completed tasks including overground and treadmill ambulation, picking up objects, shoveling, postural stability, range of motion testing, and recovery from the kneeling and prone positions. Metabolic, biomechanical, and/or subjective data were collected based on task. RESULTS: Initial analyses suggest that subjects completed all tasks with lower levels of compensation and a more terrestrial approach to movement when suspended via GIM. With SB, subjects were not able to fall or get into a prone position and had increased difficulty both retrieving objects off the floor and with overground ambulation, especially at gait initiation, because they were unable to bend their torso. GIM shows promise as a new method.

Alternate tube plugging criteria for steam generator tubes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cueto-Felgueroso, C.; Aparicio, C.B.

1997-02-01

The tubing of the Steam Generators constitutes more than half of the reactor coolant pressure boundary. Specific requirements governing the maintenance of steam generator tubes integrity are set in Plant Technical Specifications and in Section XI of the ASME Boiler and Pressure Vessel Code. The operating experience of Steam Generator tubes of PWR plants has shown the existence of some types of degradatory processes. Every one of these has an specific cause and affects one or more zones of the tubes. In the case of Spanish Power Plants, and depending on the particular Plant considered, they should be mentioned themore » Primary Water Stress Corrosion Cracking (PWSCC) at the roll transition zone (RTZ), the Outside Diameter Stress Corrosion Cracking (ODSCC) at the Tube Support Plate (TSP) intersections and the fretting with the Anti-Vibration Bars (AVBs) or with the Support Plates in the preheater zone. The In-Service Inspections by Eddy Currents constitutes the standard method for assuring the SG tubes integrity and they permit the monitoring of the defects during the service life of the plant. When the degradation reaches a determined limit, called the plugging limit, the SG tube must be either repaired or retired from service by plugging. Customarily, the plugging limit is related to the depth of the defect. Such depth is typically 40% of the wall thickness of the tube and is applicable to any type of defect in the tube. In its origin, that limit was established for tubes thinned by wastage, which was the predominant degradation in the seventies. The application of this criterion for axial crack-like defects, as, for instance, those due to PWSCC in the roll transition zone, has lead to an excessive and unnecessary number of tubes being plugged. This has lead to the development of defect specific plugging criteria. Examples of the application of such criteria are discussed in the article.« less

A New Method for Interfacing Unsuited Subjects to Overhead Suspension Partial Gravity Simulators

NASA Technical Reports Server (NTRS)

Norcross, Jason; Gernhardt, Michael; Chappell, Steve; Cowley, Matt

2011-01-01

The purpose of performing unsuited testing as part of a reduced gravity extravehicular (EVA) suited human performance research program is to define baseline performance. These results are then coupled with suited test results to evaluate how the suit system affects human performance at reduced gravity. The primary drawback to this approach is that previous studies used notably different systems to interface suited and unsuited subjects to overhead-suspension, partial-gravity simulators. A spreader bar (SB) assembly previously used for unsuited tests allowed limited pitch and roll of the subject, whereas the gimbal for suited tests allowed more pitch and roll, although the mass distribution led to large moments of inertia in the yaw axis. It is hypothesized that use of the same methods for offload of both unsuited and suited subjects is needed to make meaningful comparisons. A new gimbal (GIM) was designed with the idea that it could function with both suited and unsuited subjects. GIM was designed to minimize mass and moments of inertia and to be adjustable to co-locate the 3 axes of rotation with the subject s center of gravity. OBJECTIVE: To evaluate human performance differences between SB and GIM. METHODS: Ten unsuited subjects were offloaded to 1/6-g using both interfaces. Subjects completed tasks including overground and treadmill ambulation, picking up objects, shoveling, postural stability, range of motion testing, and recovery from the kneeling and prone positions. Metabolic, biomechanical, and/or subjective data were collected based on task. RESULTS: Initial analyses suggest that subjects completed all tasks with lower levels of compensation and a more terrestrial approach to movement when suspended via GIM. With SB, subjects were not able to fall or get into a prone position and had increased difficulty both retrieving objects off the floor and with overground ambulation, especially at gait initiation, because they were unable to bend their torso. GIM shows promise as a new method.

A method to design blended rolled edges for compact range reflectors

NASA Technical Reports Server (NTRS)

Gupta, Inder J.; Burnside, Walter D.

1989-01-01

A method to design blended rolled edges for arbitrary rim shape compact range reflectors is presented. The reflectors may be center-fed or offset-fed. The method leads to rolled edges with minimal surface discontinuities. It is shown that the reflectors designed using the prescribed method can be defined analytically using simple expressions. A procedure to obtain optimum rolled edges parameter is also presented. The procedure leads to blended rolled edges that minimize the diffracted fields emanating from the junction between the paraboloid and the rolled edge surface while satisfying certain constraints regarding the reflector size and the minimum operating frequency of the system.

Working Performance Analysis of Rolling Bearings Used in Mining Electric Excavator Crowd Reducer

NASA Astrophysics Data System (ADS)

Zhang, Y. H.; Hou, G.; Chen, G.; Liang, J. F.; Zheng, Y. M.

2017-12-01

Refer to the statistical load data of digging process, on the basis of simulation analysis of crowd reducer system dynamics, the working performance simulation analysis of rolling bearings used in crowd reducer of large mining electric excavator is completed. The contents of simulation analysis include analysis of internal load distribution, rolling elements contact stresses and rolling bearing fatigue life. The internal load characteristics of rolling elements in cylindrical roller bearings are obtained. The results of this study identified that all rolling bearings satisfy the requirements of contact strength and fatigue life. The rationality of bearings selection and arrangement is also verified.

A method to design blended rolled edges for compact range reflectors

NASA Technical Reports Server (NTRS)

Gupta, Inder J.; Ericksen, Kurt P.; Burnside, Walter D.

1990-01-01

A method to design blended rolled edges for arbitrary rim shape compact range reflectors is presented. The reflectors may be center-fed or offset-fed. The method leads to rolled edges with minimal surface discontinuities. It is shown that the reflectors designed using the prescribed method can be defined analytically using simple expressions. A procedure to obtain optimum rolled edges parameters is also presented. The procedure leads to blended rolled edges that minimize the diffracted fields emanating from the junction between the paraboloid and the rolled edge surface while satisfying certain constraints regarding the reflector size and the minimum operating frequency of the system.

Recycling strategy of the end-of-life rolling stock in China

NASA Astrophysics Data System (ADS)

Guo, L.; Wang, X. W.; Lin, Y.; Shen, X. F.; Liu, Y. Q.

2018-03-01

China's high-speed railway industry is growing fast, the side effect is that plenty of rolling stock come to the end of life each year. However, there are not relevant standards nor regulations for the recycling of rolling stock in China, which causes pollution and a waste of resources. In this paper, the basic meaning and characteristics of the circular economy is reviewed and applied to the rolling stock industry. The recycling steps are elaborated in detail according to the characteristics of rolling stock. The result proves that circular economy has both the theoretical and practical meaning in the rolling stock recycling industry in China.

E-selectin ligand-1 controls circulating prostate cancer cell rolling/adhesion and metastasis

PubMed Central

Yasmin-Karim, Sayeda; King, Michael R.; Messing, Edward M.; Lee, Yi-Fen

2014-01-01

Circulating prostate cancer (PCa) cells preferentially roll and adhere on bone marrow vascular endothelial cells, where abundant E-selectin and stromal cell-derived factor 1 (SDF-1) are expressed, subsequently initiating a cascade of activation events that eventually lead to the development of metastases. To elucidate the roles of circulating PCa cells' rolling and adhesion behaviors in cancer metastases, we applied a dynamic cylindrical flow-based microchannel device that is coated with E-selectin and SDF-1, mimicking capillary endothelium. Using this device we captured a small fraction of rolling PCa cells. These rolling cells display higher static adhesion ability, more aggressive cancer phenotypes and stem-like properties. Importantly, mice received rolling PCa cells, but not floating PCa cells, developed cancer metastases. Genes coding for E-selectin ligands and genes associated with cancer stem cells and metastasis were elevated in rolling PCa cells. Knock down of E-selectin ligand 1(ESL-1), significantly impaired PCa cells' rolling capacity and reduced cancer aggressiveness. Moreover, ESL-1 activates RAS and MAP kinase signal cascade, consequently inducing the downstream targets. In summary, circulating PCa cells' rolling capacity contributes to PCa metastasis, and that is in part controlled by ESL-1. PMID:25301730

Influence of 10 % Cold Rolling Reduction on Ageing Behaviour of Hot Rolled Al-Cu-Si-Mn-Mg Alloy

NASA Astrophysics Data System (ADS)

Ghosh, S. K.

2014-10-01

In the current study, the effect of 10 % cold rolling on the different ageing phenomena of Al-Cu-Si-Mn-Mg alloy was investigated. Both hot rolled and cold rolled alloys were subjected to both natural and artificial ageing processes. Hardness was measured to understand the change in the mechanical property of the alloy before and after rolling and also during ageing processes. From microscopy, it was evident that the cold rolling and subsequent ageing provided the alloy with a structure in which CuAl2 precipitates were uniformly distributed. The alloy exhibited the peak hardness value of 92 VHN after 2 days of natural ageing, whereas the cold deformed (10 %) alloy exhibited the higher peak hardness value of 139 VHN after 3 days of natural ageing. Peak hardness of the alloy reached 94 VHN, when hot rolled alloy was subjected to ageing at 250 °C for 1 h, whereas 10 % cold rolling followed by ageing (100 °C, 15 min) demonstrated accelerated and elevated hardening. The ageing behaviours thus obtained permit the alloy to provide a range of desirable combinations of strength and ductility for high strength weight saving applications.

Roll forming of eco-friendly stud

NASA Astrophysics Data System (ADS)

Keum, Y. T.; Lee, S. Y.; Lee, T. H.; Sim, J. K.

2013-12-01

In order to manufacture an eco-friendly stud, the sheared pattern is designed by the Taguchi method and expanded by the side rolls. The seven geometrical shape of sheared pattern are considered in the structural and thermal analyses to select the best functional one in terms of the durability and fire resistance of dry wall. For optimizing the size of the sheared pattern chosen, the L9 orthogonal array and smaller-the-better characteristics of the Taguchi method are used. As the roll gap causes forming defects when the upper-and-lower roll type is adopted for expanding the sheared pattern, the side roll type is introduced. The stress and strain distributions obtained by the FEM simulation of roll-forming processes are utilized for the design of expanding process. The expanding process by side rolls shortens the length of expanding process and minimizes the cost of dies. Furthermore, the stud manufactured by expanding the sheared pattern of the web is an eco-friend because of the scrapless roll-forming process. In addition, compared to the conventionally roll-formed stud, the material cost is lessened about 13.6% and the weight is lightened about 15.5%.

Effect of cold rolling on microstructure and mechanical property of extruded Mg–4Sm alloy during aging

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Rongguang, E-mail: lirongguang1980@126.com; Xin, Renlong; Chapuis, Adrien

Microstructure and mechanical properties of the Mg–4Sm (wt.%) alloy, prepared via combined processes of extrusion, cold rolling and aging, have been investigated. The hot extruded alloy exhibits a weak rare earth magnesium alloy texture with < 11 − 21 >//ED, while the cold-rolled alloy shows a stronger basal texture with < 0001 >//ND. Many tensile twins and double twins are observed in grains after rolling. The cold-rolled alloy shows a weak age-hardening response compared with the extruded alloy, which is the result of more precipitation in the twin boundary during aging. The rolled alloy exhibits almost no precipitate free zonemore » during aging compared with the extruded alloy. The higher proof stress of the rolled alloy in peak-aged condition is attributed to the presence of twin boundaries, stronger basal texture, higher dislocation density, and the suppression of precipitate free zone compared with the extruded alloy. - Highlights: • No precipitate free zone appears in cold-rolled alloy after aging. • Segregation and precipitates are observed in twin boundaries and grain boundaries. • Cold-rolled alloy shows a weak age-hardening response.« less

An approach to develop an algorithm to detect the climbing height in radial-axial ring rolling

NASA Astrophysics Data System (ADS)

Husmann, Simon; Hohmann, Magnus; Kuhlenkötter, Bernd

2017-10-01

Radial-axial ring rolling is the mainly used forming process to produce seamless rings, which are applied in miscellaneous industries like the energy sector, the aerospace technology or in the automotive industry. Due to the simultaneously forming in two opposite rolling gaps and the fact that ring rolling is a mass forming process, different errors could occur during the rolling process. Ring climbing is one of the most occurring process errors leading to a distortion of the ring's cross section and a deformation of the rings geometry. The conventional sensors of a radial-axial rolling machine could not detect this error. Therefore, it is a common strategy to roll a slightly bigger ring, so that random occurring process errors could be reduce afterwards by removing the additional material. The LPS installed an image processing system to the radial rolling gap of their ring rolling machine to enable the recognition and measurement of climbing rings and by this, to reduce the additional material. This paper presents the algorithm which enables the image processing system to detect the error of a climbing ring and ensures comparable reliable results for the measurement of the climbing height of the rings.

Dynamics of colloidal particles in electrohydrodynamic convection of nematic liquid crystal.

PubMed

Takahashi, Kentaro; Kimura, Yasuyuki

2014-07-01

We have studied the dynamics of micrometer-sized colloidal particles in electrohydrodynamic convection of nematic liquid crystal. Above the onset voltage of electroconvection, the parallel array of convection rolls appears to be perpendicular to the nematic field at first. The particles are forced to rotate by convection flow and are trapped within a single roll in this voltage regime. A slow glide motion along the roll axis is also observed. The frequency of rotational motion and the glide velocity increase with the applied voltage. Under a much larger voltage where the roll axis temporally fluctuates, the particles occasionally hop to the neighbor rolls. In this voltage regime, the motion of the particles becomes two-dimensional. The motion perpendicular to the roll axis exhibits diffusion behavior at a long time period. The effective diffusion constant is 10(3)-10(4) times larger than the molecular one. The observed behavior is compared with the result obtained by a simple stochastic model for the transport of the particles in convection. The enhancement of diffusion can be quantitatively described well by the rotation frequency in a roll, the width of the roll, and the hopping probability to the neighbor rolls.

Effects of False Tilt Cues on the Training of Manual Roll Control Skills

NASA Technical Reports Server (NTRS)

Zaal, Peter M. T.; Popovici, Alexandru; Zavala, Melinda A.

2015-01-01

This paper describes a transfer-of-training study performed in the NASA Ames Vertica lMotion Simulator. The purpose of the study was to investigate the effect of false tilt cues on training and transfer of training of manual roll control skills. Of specific interest were the skills needed to control unstable roll dynamics of a mid-size transport aircraft close to the stall point. Nineteen general aviation pilots trained on a roll control task with one of three motion conditions: no motion, roll motion only, or reduced coordinated roll motion. All pilots transferred to full coordinated roll motion in the transfer session. A novel multimodal pilot model identification technique was successfully applied to characterize how pilots' use of visual and motion cues changed over the course of training and after transfer. Pilots who trained with uncoordinated roll motion had significantly higher performance during training and after transfer, even though they experienced the false tilt cues. Furthermore, pilot control behavior significantly changed during the two sessions, as indicated by increasing visual and motion gains, and decreasing lead time constants. Pilots training without motion showed higher learning rates after transfer to the full coordinated roll motion case.

40 CFR 467.20 - Applicability; description of the rolling with emulsions subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... rolling with emulsions subcategory. 467.20 Section 467.20 Protection of Environment ENVIRONMENTAL... CATEGORY Rolling With Emulsions Subcategory § 467.20 Applicability; description of the rolling with emulsions subcategory. This subpart applies to dischargers of pollutants to waters of the United States and...

40 CFR 467.20 - Applicability; description of the rolling with emulsions subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... rolling with emulsions subcategory. 467.20 Section 467.20 Protection of Environment ENVIRONMENTAL... CATEGORY Rolling With Emulsions Subcategory § 467.20 Applicability; description of the rolling with emulsions subcategory. This subpart applies to dischargers of pollutants to waters of the United States and...

40 CFR 467.20 - Applicability; description of the rolling with emulsions subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... rolling with emulsions subcategory. 467.20 Section 467.20 Protection of Environment ENVIRONMENTAL... CATEGORY Rolling With Emulsions Subcategory § 467.20 Applicability; description of the rolling with emulsions subcategory. This subpart applies to dischargers of pollutants to waters of the United States and...

49 CFR 393.122 - What are the rules for securing paper rolls?

Code of Federal Regulations, 2011 CFR

2011-10-01

.... (3) The blocking roll must be at least 38 mm (1.5 in) taller than other rolls, or must be raised at... is at least 1.5 times taller than the diameter of the roll being blocked, or (iii) Placing it in a...

Effect of Hot Rolling on the Microstructure and Mechanical Properties of Nitrogen Alloyed Austenitic Stainless Steel

NASA Astrophysics Data System (ADS)

Chenna Krishna, S.; Karthick, N. K.; Jha, Abhay K.; Pant, Bhanu; Cherian, Roy M.

2018-05-01

In the present investigation, the effect of multi-pass hot rolling in the temperature range of 700-1000 °C on the microstructure and mechanical properties of nitrogen alloyed austenitic stainless steel was studied with the aid of optical microscopy, tensile testing and x-ray diffraction measurements. The microstructural changes that occurred in the hot rolled specimens were elongation of grains in rolling direction, nucleation of new grains at the grain boundaries of elongated grains and growth of nucleated grains to form fully recrystallized grains. Elongated grains formed at lower rolling temperature (700-800 °C) due to inadequate strain/temperature for the initiation of dynamic recrystallization. At higher rolling temperature (900-1000 °C), fine grains formed due to dynamic recrystallization. Tensile properties showed strong dependency on the rolling temperature. Tensile strength increased with the decrease in the rolling temperature at the cost of ductility. Maximum strength was observed in samples hot rolled at 700 °C with yield strength of 917 MPa and ductility of 25%. This variation in the tensile properties with the rolling temperature is attributed to changes in the dislocation density and grain structure. The estimated yield strength from the dislocation density, solid solution and grain boundary strengthening closely matched with experimentally determined yield strength confirming the role of dislocation density and grain size in the strengthening.

A Pilot Opinion Study of Lateral Control Requirements for Fighter-Type Aircraft

NASA Technical Reports Server (NTRS)

Creer, Brent Y.; Stewart, John D.; Merrick, Robert B.; Drinkwater, Fred J., III

1959-01-01

As part of a continuing NASA program of research on airplane handling qualities, a pilot opinion investigation has been made on the lateral control requirements of fighter aircraft flying in their combat speed range. The investigation was carried out using a stationary flight simulator and a moving flight simulator, and the flight simulator results were supplemented by research tests in actual flight. The flight simulator study was based on the presumption that the pilot rates the roll control of an airplane primarily on a single-degree-of-freedom basis; that is, control of angle of roll about the aircraft body axis being of first importance. From the assumption of a single degree of freedom system it follows that there are two fundamental parameters which govern the airplane roll response, namely the roll damping expressed as a time constant and roll control power in terms of roll acceleration. The simulator study resulted in a criterion in terms of these two parameters which defines satisfactory, unsatisfactory, and unacceptable roll performance from a pilot opinion standpoint. The moving simulator results were substantiated by the in-flight investigation. The derived criterion was compared with the roll performance criterion based upon wing tip helix angle and also with other roll performance concepts which currently influence the roll performance design of military fighter aircraft flying in their combat speed range.

Effect of Hot Rolling on the Microstructure and Mechanical Properties of Nitrogen Alloyed Austenitic Stainless Steel

NASA Astrophysics Data System (ADS)

Chenna Krishna, S.; Karthick, N. K.; Jha, Abhay K.; Pant, Bhanu; Cherian, Roy M.

2018-04-01

In the present investigation, the effect of multi-pass hot rolling in the temperature range of 700-1000 °C on the microstructure and mechanical properties of nitrogen alloyed austenitic stainless steel was studied with the aid of optical microscopy, tensile testing and x-ray diffraction measurements. The microstructural changes that occurred in the hot rolled specimens were elongation of grains in rolling direction, nucleation of new grains at the grain boundaries of elongated grains and growth of nucleated grains to form fully recrystallized grains. Elongated grains formed at lower rolling temperature (700-800 °C) due to inadequate strain/temperature for the initiation of dynamic recrystallization. At higher rolling temperature (900-1000 °C), fine grains formed due to dynamic recrystallization. Tensile properties showed strong dependency on the rolling temperature. Tensile strength increased with the decrease in the rolling temperature at the cost of ductility. Maximum strength was observed in samples hot rolled at 700 °C with yield strength of 917 MPa and ductility of 25%. This variation in the tensile properties with the rolling temperature is attributed to changes in the dislocation density and grain structure. The estimated yield strength from the dislocation density, solid solution and grain boundary strengthening closely matched with experimentally determined yield strength confirming the role of dislocation density and grain size in the strengthening.

The Carnegie-Irvine Galaxy Survey. V. Statistical Study of Bars and Buckled Bars

NASA Astrophysics Data System (ADS)

Li, Zhao-Yu; Ho, Luis C.; Barth, Aaron J.

2017-08-01

Simulations have shown that bars are subject to a vertical buckling instability that transforms thin bars into boxy or peanut-shaped structures, but the physical conditions necessary for buckling to occur are not fully understood. We use the large sample of local disk galaxies in the Carnegie-Irvine Galaxy Survey to examine the incidence of bars and buckled bars across the Hubble sequence. Depending on the disk inclination angle (I), a buckled bar reveals itself as either a boxy/peanut-shaped bulge (at high I) or as a barlens structure (at low I). We visually identify bars, boxy/peanut-shaped bulges, and barlenses, and examine the dependence of bar and buckled bar fractions on host galaxy properties, including Hubble type, stellar mass, color, and gas mass fraction. We find that the barred and unbarred disks show similar distributions in these physical parameters. The bar fraction is higher (70%-80%) in late-type disks with low stellar mass (M * < 1010.5 M ⊙) and high gas mass ratio. In contrast, the buckled bar fraction increases to 80% toward massive and early-type disks (M * > 1010.5 M ⊙), and decreases with higher gas mass ratio. These results suggest that bars are more difficult to grow in massive disks that are dynamically hotter than low-mass disks. However, once a bar forms, it can easily buckle in the massive disks, where a deeper potential can sustain the vertical resonant orbits. We also find a probable buckling bar candidate (ESO 506-G004) that could provide further clues to understand the timescale of the buckling process.

Galaxy Zoo: Observing secular evolution through bars

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cheung, Edmond; Faber, S. M.; Koo, David C.

In this paper, we use the Galaxy Zoo 2 data set to study the behavior of bars in disk galaxies as a function of specific star formation rate (SSFR) and bulge prominence. Our sample consists of 13,295 disk galaxies, with an overall (strong) bar fraction of 23.6% ± 0.4%, of which 1154 barred galaxies also have bar length (BL) measurements. These samples are the largest ever used to study the role of bars in galaxy evolution. We find that the likelihood of a galaxy hosting a bar is anticorrelated with SSFR, regardless of stellar mass or bulge prominence. We findmore » that the trends of bar likelihood and BL with bulge prominence are bimodal with SSFR. We interpret these observations using state-of-the-art simulations of bar evolution that include live halos and the effects of gas and star formation. We suggest our observed trends of bar likelihood with SSFR are driven by the gas fraction of the disks, a factor demonstrated to significantly retard both bar formation and evolution in models. We interpret the bimodal relationship between bulge prominence and bar properties as being due to the complicated effects of classical bulges and central mass concentrations on bar evolution and also to the growth of disky pseudobulges by bar evolution. These results represent empirical evidence for secular evolution driven by bars in disk galaxies. This work suggests that bars are not stagnant structures within disk galaxies but are a critical evolutionary driver of their host galaxies in the local universe (z < 1).« less

Strip casting with fluxing agent applied to casting roll

DOEpatents

Williams, R.S.; O`Malley, R.J.; Sussman, R.C.

1997-07-29

A strip caster for producing a continuous strip includes a tundish for containing a melt, a pair of horizontally disposed water cooled casting rolls and devices for electrostatically coating the outer peripheral chill surfaces of the casting rolls with a powder flux material. The casting rolls are juxtaposed relative to one another for forming a pouting basin for receiving the melt through a teeming tube thereby establishing a meniscus between the rolls for forming the strip. The melt is protected from the outside air by a non-oxidizing gas passed through a supply line to a sealing chamber. A preferred flux is boron oxide having a melting point of about 550 C. The flux coating enhances wetting of the steel melt to the casting roll and dissolves any metal oxide formed on the roll. 3 figs.

Application of Roll-Isolated Inertial Measurement Units to the Instrumentation of Spinning Vehicles

DOE Office of Scientific and Technical Information (OSTI.GOV)

BEADER,MARK E.

Roll-isolated inertial measurement units are developed at Sandia for use in the instrumentation, guidance, and control of rapidly spinning vehicles. Roll-isolation is accomplished by supporting the inertial instrument cluster (gyros and accelerometers) on a single gimbal, the axis of which is parallel to the vehicle's spin axis. A rotary motor on the gimbal is driven by a servo loop to null the roll gyro output, thus inertially stabilizing the gimbal and instrument cluster while the vehicle spins around it. Roll-isolation prevents saturation of the roll gyro by the high vehicle spin rate, and vastly reduces measurement errors arising from gyromore » scale factor and alignment uncertainties. Nine versions of Sandia-developed roll-isolated inertial measurement units have been flown on a total of 27 flight tests since 1972.« less

In-Roll Stress Analysis Considering Air-Entrainment at the Roll-Inlet with the Effect of Grooves on Nip Roll Surface

NASA Astrophysics Data System (ADS)

Sasaki, Masashi; Tanimoto, Koshi; Kohno, Kazukiyo; Takahashi, Sadamu; Kometani, Hideo; Hashimoto, Hiromu

High-speed winding of paper web sometimes leads the winding system into unstable states, interlayer slippage of wound roll, paper breakage and so on, due to the excessive air-entrainment at the roll-inlet of nip contact region. These phenomena are more frequently observed on coated paper or plastic film comparing with newspaper, because the former allows little permeation of air and their surface roughness is small. Therefore, it is of vital importance to clarify the in-roll stress of wound roll considering the effect of air-entrainment. Generally, it is known that the amount of air-entrainment is affected by grooving shape of nip roll surface. In this paper, we focused on the grooving shape and investigated the relationship with the air-entrainment into two rolls being pressed each other and the grooving shape in order to achieve stable winding at high speed. We conducted experiments using small sized test machine. Entrained air-film thickness was evaluated applying the solution of the elasto-hydrodynamic lubrication for foil bearing with the consideration of nip profile at the grooved area. Air film thickness was measured to ensure the applicability of the above theory. Consequently, we found that the air film thickness can be estimated considering the effect of grooves on the nip roll surface, and that the validity of the above estimations was ensured from experimental investigations. Furthermore, it became to be able to propose the optimal shape of grooves on nip roll surface to maintain the stable winding at high speed and at large-diameter in reel.

Effect of deformation path on microstructure, microhardness and texture evolution of interstitial free steel fabricated by differential speed rolling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hamad, Kotiba; Chung, Bong Kwon; Ko, Young Gun, E-mail: younggun@ynu.ac.kr

2014-08-15

This paper reports the effect of the deformation path on the microstructure, microhardness, and texture evolution of interstitial free (IF) steel processed by differential speed rolling (DSR) method. For this purpose, total height reductions of 50% and 75% were imposed on the samples by a series of differential speed rolling operations with various height reductions per pass (deformation levels) ranging from 10 to 50% under a fixed roll speed ratio of 1:4 for the upper and lower rolls, respectively. Microstructural observations using transmission electron microscopy and electron backscattered diffraction measurements showed that the samples rolled at deformation level of 50%more » had the finest mean grain size (∼ 0.5 μm) compared to the other counterparts; also the samples rolled at deformation level of 50% showed a more uniform microstructure. Based on the microhardness measurements along the thickness direction of the deformed samples, gradual evolution of the microhardness value and its homogeneity was observed with the increase of the deformation level per pass. Texture analysis showed that, as the deformation level per pass increased, the fraction of alpha fiber and gamma fiber in the deformed samples increased. The textures obtained by the differential speed rolling process under the lubricated condition would be equivalent to those obtained by the conventional rolling. - Highlights: • Effect of DSR deformation path on microstructure of IF steel is significant. • IF steel rolled at deformation level of 50% has the ultrafine grains of ∼ 0.5 μm. • Rolling texture components are pronounced with increasing deformation level.« less

Oligomerization but Not Membrane Bending Underlies the Function of Certain F-BAR Proteins in Cell Motility and Cytokinesis.

PubMed

McDonald, Nathan A; Vander Kooi, Craig W; Ohi, Melanie D; Gould, Kathleen L

2015-12-21

F-BAR proteins function in diverse cellular processes by linking membranes to the actin cytoskeleton. Through oligomerization, multiple F-BAR domains can bend membranes into tubules, though the physiological importance of F-BAR-to-F-BAR assemblies is not yet known. Here, we investigate the F-BAR domain of the essential cytokinetic scaffold, Schizosaccharomyces pombe Cdc15, during cytokinesis. Challenging a widely held view that membrane deformation is a fundamental property of F-BARs, we report that the Cdc15 F-BAR binds, but does not deform, membranes in vivo or in vitro, and six human F-BAR domains-including those from Fer and RhoGAP4-share this property. Nevertheless, tip-to-tip interactions between F-BAR dimers are critical for Cdc15 oligomerization and high-avidity membrane binding, stabilization of contractile ring components at the medial cortex, and the fidelity of cytokinesis. F-BAR oligomerization is also critical for Fer and RhoGAP4 physiological function, demonstrating its broad importance to F-BAR proteins that function without membrane bending. Copyright © 2015 Elsevier Inc. All rights reserved.

78 FR 34550 - Airworthiness Directives; Rolls-Royce plc Turbojet Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-10

... Airworthiness Directives; Rolls-Royce plc Turbojet Engines AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Final rule. SUMMARY: We are adopting a new airworthiness directive (AD) for all Rolls-Royce plc..., contact Defence Aerospace Communications at Rolls-Royce plc, P.O. Box 3, Gypsy Patch Lane, Filton, Bristol...

76 FR 4100 - Combined Notice of Filings #1

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-24

..., Rolling Thunder I Power Partners, LLC, Goshen Phase II LLC, Cedar Creek II, LLC. Description: Supplemental Information of Rolling Thunder I Power Partners, LLC. Filed Date: 01/12/2011. Accession Number: 20110112-5154...: Rolling Thunder I Power Partners, LLC. Description: Rolling Thunder I Power Partners, LLC submits tariff...

78 FR 50378 - Diffusion-Annealed, Nickel-Plated Flat-Rolled Steel Products From Japan: Postponement of...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-19

...-Plated Flat-Rolled Steel Products From Japan: Postponement of Preliminary Determination of Antidumping... investigation of diffusion-annealed, nickel-plated flat-rolled steel products from Japan. See Diffusion- Annealed, Nickel-Plated Flat-Rolled Steel Products From Japan: Initiation of Antidumping Duty Investigation...

78 FR 31577 - Diffusion-Annealed, Nickel-Plated Flat-Rolled Steel Products From Japan

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-24

..., Nickel-Plated Flat-Rolled Steel Products From Japan Determination On the basis of the record \\1... imports from Japan of diffusion-annealed, nickel-plated flat-rolled steel products, provided for primarily... flat-rolled steel products from Japan. Accordingly, effective March 27, 2013, the Commission instituted...

Performance simulation of BaBar DIRC bar boxes in TORCH

NASA Astrophysics Data System (ADS)

Föhl, K.; Brook, N.; Castillo García, L.; Cussans, D.; Forty, R.; Frei, C.; Gao, R.; Gys, T.; Harnew, N.; Piedigrossi, D.; Rademacker, J.; Ros García, A.; van Dijk, M.

2017-12-01

TORCH is a large-area precision time-of-flight detector based on the DIRC principle. The DIRC bar boxes of the BaBar experiment at SLAC could possibly be reused to form a part of the TORCH detector time-of-flight wall area, proposed to provide positive particle identification of low momentum kaons in the LHCb experiment at CERN. For a potential integration of BaBar bar boxes into TORCH, new imaging readout optics are required. From the several designs of readout optics that have been considered, two are used in this paper to study the effect of BaBar bar optical imperfections on the detector reconstruction performance. The kaon-pion separation powers obtained from analysing simulated photon hit patterns show the performance reduction for a BaBar bar of non-square geometry compared to a perfectly rectangular cross section.

PREDICTIONS FOR $B \\to \\tau \\bar{\\mu} + \\mu \\bar{\\tau}$

NASA Astrophysics Data System (ADS)

Boubaa, Dris; Datta, Alakabha; Duraisamy, Murugeswaran; Khalil, Shaaban

2013-12-01

The observation of B -> τ \\bar {μ } + μ \\bar {τ } at present experiments would be a clear sign of new physics. In this paper, we calculate this process in an extended Higgs sector framework where the decay is mediated by the exchange of spin zero particle with flavor changing neutral current couplings. If we identify the scalar with the newly discovered state at LHC with a mass 125 GeV then we find that, after imposing all experimental constraints, the BR(Bs -> τ \\bar {μ } + μ \\bar {τ }) can be as high as 10-6 and BR (Bd -> τ \\bar {μ } + μ \\bar {τ }) can be as high as 10-7. We also calculate this process in the minimal supersymmetric standard model and find the BR(Bs ->τ \\bar {μ } + μ \\bar {τ }) is typically of the order 10-8.

The intrinsic three-dimensional shape of galactic bars

NASA Astrophysics Data System (ADS)

Méndez-Abreu, J.; Costantin, L.; Aguerri, J. A. L.; de Lorenzo-Cáceres, A.; Corsini, E. M.

2018-06-01

We present the first statistical study on the intrinsic three-dimensional (3D) shape of a sample of 83 galactic bars extracted from the CALIFA survey. We use the galaXYZ code to derive the bar intrinsic shape with a statistical approach. The method uses only the geometric information (ellipticities and position angles) of bars and discs obtained from a multi-component photometric decomposition of the galaxy surface-brightness distributions. We find that bars are predominantly prolate-triaxial ellipsoids (68%), with a small fraction of oblate-triaxial ellipsoids (32%). The typical flattening (intrinsic C/A semiaxis ratio) of the bars in our sample is 0.34, which matches well the typical intrinsic flattening of stellar discs at these galaxy masses. We demonstrate that, for prolate-triaxial bars, the intrinsic shape of bars depends on the galaxy Hubble type and stellar mass (bars in massive S0 galaxies are thicker and more circular than those in less massive spirals). The bar intrinsic shape correlates with bulge, disc, and bar parameters. In particular with the bulge-to-total (B/T) luminosity ratio, disc g - r color, and central surface brightness of the bar, confirming the tight link between bars and their host galaxies. Combining the probability distributions of the intrinsic shape of bulges and bars in our sample we show that 52% (16%) of bulges are thicker (flatter) than the surrounding bar at 1σ level. We suggest that these percentages might be representative of the fraction of classical and disc-like bulges in our sample, respectively.

How Gaussian can our Universe be?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cabass, G.; Pajer, E.; Schmidt, F., E-mail: giovanni.cabass@roma1.infn.it, E-mail: e.pajer@uu.nl, E-mail: fabians@mpa-garching.mpg.de

Gravity is a non-linear theory, and hence, barring cancellations, the initial super-horizon perturbations produced by inflation must contain some minimum amount of mode coupling, or primordial non-Gaussianity. In single-field slow-roll models, where this lower bound is saturated, non-Gaussianity is controlled by two observables: the tensor-to-scalar ratio, which is uncertain by more than fifty orders of magnitude; and the scalar spectral index, or tilt, which is relatively well measured. It is well known that to leading and next-to-leading order in derivatives, the contributions proportional to the tilt disappear from any local observable, and suspicion has been raised that this might happenmore » to all orders, allowing for an arbitrarily low amount of primordial non-Gaussianity. Employing Conformal Fermi Coordinates, we show explicitly that this is not the case. Instead, a contribution of order the tilt appears in local observables. In summary, the floor of physical primordial non-Gaussianity in our Universe has a squeezed-limit scaling of k {sub ℓ}{sup 2}/ k {sub s} {sup 2}, similar to equilateral and orthogonal shapes, and a dimensionless amplitude of order 0.1 × ( n {sub s}−1).« less

Design and control of compliant tensegrity robots through simulation and hardware validation

PubMed Central

Caluwaerts, Ken; Despraz, Jérémie; Işçen, Atıl; Sabelhaus, Andrew P.; Bruce, Jonathan; Schrauwen, Benjamin; SunSpiral, Vytas

2014-01-01

To better understand the role of tensegrity structures in biological systems and their application to robotics, the Dynamic Tensegrity Robotics Lab at NASA Ames Research Center, Moffett Field, CA, USA, has developed and validated two software environments for the analysis, simulation and design of tensegrity robots. These tools, along with new control methodologies and the modular hardware components developed to validate them, are presented as a system for the design of actuated tensegrity structures. As evidenced from their appearance in many biological systems, tensegrity (‘tensile–integrity’) structures have unique physical properties that make them ideal for interaction with uncertain environments. Yet, these characteristics make design and control of bioinspired tensegrity robots extremely challenging. This work presents the progress our tools have made in tackling the design and control challenges of spherical tensegrity structures. We focus on this shape since it lends itself to rolling locomotion. The results of our analyses include multiple novel control approaches for mobility and terrain interaction of spherical tensegrity structures that have been tested in simulation. A hardware prototype of a spherical six-bar tensegrity, the Reservoir Compliant Tensegrity Robot, is used to empirically validate the accuracy of simulation. PMID:24990292

A new chaotic multi-verse optimization algorithm for solving engineering optimization problems

NASA Astrophysics Data System (ADS)

Sayed, Gehad Ismail; Darwish, Ashraf; Hassanien, Aboul Ella

2018-03-01

Multi-verse optimization algorithm (MVO) is one of the recent meta-heuristic optimization algorithms. The main inspiration of this algorithm came from multi-verse theory in physics. However, MVO like most optimization algorithms suffers from low convergence rate and entrapment in local optima. In this paper, a new chaotic multi-verse optimization algorithm (CMVO) is proposed to overcome these problems. The proposed CMVO is applied on 13 benchmark functions and 7 well-known design problems in the engineering and mechanical field; namely, three-bar trust, speed reduce design, pressure vessel problem, spring design, welded beam, rolling element-bearing and multiple disc clutch brake. In the current study, a modified feasible-based mechanism is employed to handle constraints. In this mechanism, four rules were used to handle the specific constraint problem through maintaining a balance between feasible and infeasible solutions. Moreover, 10 well-known chaotic maps are used to improve the performance of MVO. The experimental results showed that CMVO outperforms other meta-heuristic optimization algorithms on most of the optimization problems. Also, the results reveal that sine chaotic map is the most appropriate map to significantly boost MVO's performance.

An investigation of the tri-bar gripping system on isometric muscular endurance.

PubMed

Drury, Daniel G; Faggiono, Heath; Stuempfle, Kristin J

2004-11-01

Recently, a new product called the Tri-Bar has been introduced as an alternative to the standard round weightlifting bar. The Tri-Bar has the same weight, length, and circumference as a standard weightlifting bar and differs only in that the shape of the bar is formed like a triangle with rounded edges. Theoretically, the shape of the bar will enhance gripping comfort and increase muscular endurance. We studied 32 moderately trained males who were free from upper-body injury or limitation. Each participant completed 4 visits to the lab as part of 2 separate investigations. The first investigation was a comparison of straight-arm hang times while grasping a standard Olympic bar or a Tri-Bar attached to the top of a power rack. The second investigation involved grasping a standard revolving cable handle or a Tri-Bar revolving handle attached to a weight equal to half the subject's body weight. In both investigations, time was used as a measure of isometric muscular endurance. Differences were determined using a dependent t-test, and a level of significance was set at p < 0.05. Mean hang times were significantly longer when the men hung from the Tri-Bar (107.6 seconds) versus the standard bar (95.4 seconds) (p = 0.015). Conversely, in the investigation using the revolving handles, the round bar produced longer grasping times (71.5 seconds) than the Tri-Bar (62.6 seconds) (p = 0.000). The results of this investigation indicate that a fixed and stable Tri-Bar may help to increase hang time, but a Tri-Bar free to rotate within the grasp may decrease grasping time in comparison to a standard round handle. With regard to exercises that require isometric grasping, the Tri-Bar may be an effective alternative to the standard bar for increasing isometric grasping endurance.

Interference of Nonstandard Interactions with Standard Model in {B^0} \\to {π ^0}\\bar vv, B_c^ - \\to {D^ - }\\bar vv and \\bar B_s^0 \\to {K^0}\\bar vv Decays

NASA Astrophysics Data System (ADS)

Mahmood, Shakeel; Tahir, Farida; Mir, Azeem

2018-05-01

We study the contributions of nonstandard neutrino interactions (NSI) to the rare decays of pseudoscalar mesons involving neutrinos in the final state {B^0} \\to {π ^0}\\bar vv, B_c^ - \\to {D^ - }\\bar vv and \\bar B_s^0 \\to {\\bar K^0}\\bar vv, It is pointed that dominant contribution comes from the interference between standard model and nonstandard interaction We predict limits on NSIs free parameter ɛ uL ττ and compare them with experimental data. We further compare our results with perturbative QCD (pQCD) and QCD results for these reactions.

Secular Evolution in Barred Galaxies: Observations

NASA Astrophysics Data System (ADS)

Merrifield, M.

2002-12-01

This paper describes a framework for studying galaxy morphology, particularly bar strength, in a quantitative manner, and presents applications of this approach that reveal observational evidence for secular evolution in bar morphology. The distribution of bar strength in galaxies is quite strongly bimodal, suggesting that barred and unbarred systems are distinct entities, and that any evolution between these two states must occur on a relatively rapid timescale. Bars' strengths appear to be correlated with their pattern speeds, implying that these structures weaken as they start to slow, and disappear entirely before the bars have slowed significantly. There is also tantalizing evidence that bars are rare beyond a redshift of z ~ 0.7, indicating that galaxies have only recently evolved to a point where bars can readily form.

In-line metrology for roll-to-roll UV assisted nanoimprint lithography using diffractometry

NASA Astrophysics Data System (ADS)

Kreuzer, Martin; Whitworth, Guy L.; Francone, Achille; Gomis-Bresco, Jordi; Kehagias, Nikolaos; Sotomayor-Torres, Clivia M.

2018-05-01

We describe and discuss the optical design of a diffractometer to carry out in-line quality control during roll-to-roll nanoimprinting. The tool measures diffractograms in reflection geometry, through an aspheric lens to gain fast, non-invasive information of any changes to the critical dimensions of target grating structures. A stepwise tapered linear grating with constant period was fabricated in order to detect the variation in grating linewidth through diffractometry. The minimum feature change detected was ˜40 nm to a precision of 10 nm. The diffractometer was then integrated with a roll-to-roll UV assisted nanoimprint lithography machine to gain dynamic measurements in situ.

Rolled-up inductor structure for a radiofrequency integrated circuit (RFIC)

DOEpatents

Li, Xiuling; Huang, Wen; Ferreira, Placid M.; Yu, Xin

2015-12-29

A rolled-up inductor structure for a radiofrequency integrated circuit (RFIC) comprises a multilayer sheet in a rolled configuration comprising multiple turns about a longitudinal axis. The multilayer sheet comprises a conductive pattern layer on a strain-relieved layer, and the conductive pattern layer comprises at least one conductive strip having a length extending in a rolling direction. The at least one conductive strip thereby wraps around the longitudinal axis in the rolled configuration. The conductive pattern layer may also comprise two conductive feed lines connected to the conductive strip for passage of electrical current therethrough. The conductive strip serves as an inductor cell of the rolled-up inductor structure.

Rolled-up transmission line structure for a radiofrequency integrated circuit (RFIC)

DOEpatents

Li, Xiuling; Huang, Wen

2015-04-28

A rolled-up transmission line structure for a radiofrequency integrated circuit (RFIC) comprises a multilayer sheet in a rolled configuration comprising multiple turns about a longitudinal axis, where the multilayer sheet comprises a conductive pattern layer on a strain-relieved layer. The conductive pattern layer comprises a first conductive film and a second conductive film separated from the first conductive film in a rolling direction. In the rolled configuration, the first conductive film surrounds the longitudinal axis, and the second conductive film surrounds the first conductive film. The first conductive film serves as a signal line and the second conductive film serves as a conductive shield for the rolled-up transmission line structure.

The surprising rolling spool: librational motion and failure of the pure rolling condition

NASA Astrophysics Data System (ADS)

Onorato, P.; Malgieri, M.; Mascheretti, P.; De Ambrosis, A.

2015-05-01

In a previous work (Onorato P, Malgieri M, Mascheretti P and De Ambrosis A 2014 The surprising rolling spool: experiments and theory from mechanics to phase transitions Eur. J. Phys. 35 055011) an asymmetric rolling spool (ARS) was investigated as a simple model for a second-order phase transition. Here, we deepen the study of this system to address critical aspects related both to the characteristic of the oscillatory anharmonic motion and to the role of friction forces in determining it. The experimental data show that for largely asymmetric bodies the rolling condition is not reliably fulfilled because the intensity of the friction force goes below the needed value to ensure rolling without slipping.

State dynamics of a double sandbar system

NASA Astrophysics Data System (ADS)

Price, T. D.; Ruessink, B. G.

2011-04-01

A 9.3-year dataset of low-tide time-exposure images from Surfers Paradise, Northern Gold Coast, Australia was used to characterise the state dynamics of a double sandbar system. The morphology of the nearshore sandbars was described by means of the sequential bar state classification scheme of Wright and Short [1984. Morphodynamic variability of surf zones and beaches: a synthesis. Marine Geology 56, 93-118]. Besides the two end members (the dissipative (D) and the reflective (R) states) and the four intermediate states (longshore bar and trough (LBT), rhythmic bar and beach (RBB), transverse bar and rip (TBR) and low tide terrace (LTT)), we identified two additional intermediate bar states. The erosive transverse bar and rip (eTBR) state related to the dominant oblique angle of wave incidence at the study site and the rhythmic low tide terrace (rLTT) related to the multiple bar setting. Using the alongshore barline variability and alongshore trough continuity as morphological indicators enabled the objective classification of the inner and outer bar states from the images. The outer bar was mostly in the TBR state and generally advanced sequentially through the states LBT-RBB-TBR-eTBR-LBT, with occasional transitions to the D state. Wave events led to abrupt state transitions of the outer bar, but, in contrast to expectations, did not necessarily correspond to upstate transitions. Instead, upstate (downstate) transitions coincided with angles of wave incidence θ larger (smaller) than 30°. The upstate TBR-eTBR-LBT sequence during high-angle events highlights the role of alongshore currents in bar straightening. The outer bar was found to govern the state of the inner bar to a large extent. Two types of inner bar behaviour were distinguished, based on the outer bar state. For intermediate outer bar states, the alongshore variability of the dominant inner rLTT state (52% in time) mainly related to that of the outer bar, implying some sort of morphological coupling. For dissipative outer bar states, however, the more upstate inner bar frequently separated from the shoreline and persistently developed rip channels as TBR became the most frequent state (60% in time).

The F-BAR domains from srGAP1, srGAP2 and srGAP3 regulate membrane deformation differently

PubMed Central

Coutinho-Budd, Jaeda; Ghukasyan, Vladimir; Zylka, Mark J.; Polleux, Franck

2012-01-01

Summary Coordination of membrane deformation and cytoskeletal dynamics lies at the heart of many biological processes critical for cell polarity, motility and morphogenesis. We have recently shown that Slit-Robo GTPase-activating protein 2 (srGAP2) regulates neuronal morphogenesis through the ability of its F-BAR domain to regulate membrane deformation and induce filopodia formation. Here, we demonstrate that the F-BAR domains of two closely related family members, srGAP1 and srGAP3 [designated F-BAR(1) and F-BAR(3), respectively] display significantly different membrane deformation properties in non-neuronal COS7 cells and in cortical neurons. F-BAR(3) induces filopodia in both cell types, though less potently than F-BAR(2), whereas F-BAR(1) prevents filopodia formation in cortical neurons and reduces plasma membrane dynamics. These three F-BAR domains can heterodimerize, and they act synergistically towards filopodia induction in COS7 cells. As measured by fluorescence recovery after photobleaching, F-BAR(2) displays faster molecular dynamics than F-BAR(3) and F-BAR(1) at the plasma membrane, which correlates well with its increased potency to induce filopodia. We also show that the molecular dynamic properties of F-BAR(2) at the membrane are partially dependent on F-Actin. Interestingly, acute phosphatidylinositol 4,5-bisphosphate [PtdIns(4,5)P2] depletion in cells does not interfere with plasma membrane localization of F-BAR(2), which is compatible with our result showing that F-BAR(2) binds to a broad range of negatively-charged phospholipids present at the plasma membrane, including phosphatidylserine (PtdSer). Overall, our results provide novel insights into the functional diversity of the membrane deformation properties of this subclass of F-BAR-domains required for cell morphogenesis. PMID:22467852

The Carnegie-Irvine Galaxy Survey. V. Statistical Study of Bars and Buckled Bars

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Zhao-Yu; Ho, Luis C.; Barth, Aaron J., E-mail: lizy@shao.ac.cn

Simulations have shown that bars are subject to a vertical buckling instability that transforms thin bars into boxy or peanut-shaped structures, but the physical conditions necessary for buckling to occur are not fully understood. We use the large sample of local disk galaxies in the Carnegie-Irvine Galaxy Survey to examine the incidence of bars and buckled bars across the Hubble sequence. Depending on the disk inclination angle ( i ), a buckled bar reveals itself as either a boxy/peanut-shaped bulge (at high i ) or as a barlens structure (at low i ). We visually identify bars, boxy/peanut-shaped bulges, andmore » barlenses, and examine the dependence of bar and buckled bar fractions on host galaxy properties, including Hubble type, stellar mass, color, and gas mass fraction. We find that the barred and unbarred disks show similar distributions in these physical parameters. The bar fraction is higher (70%–80%) in late-type disks with low stellar mass ( M {sub *} < 10{sup 10.5} M {sub ⊙}) and high gas mass ratio. In contrast, the buckled bar fraction increases to 80% toward massive and early-type disks ( M {sub *} > 10{sup 10.5} M {sub ⊙}), and decreases with higher gas mass ratio. These results suggest that bars are more difficult to grow in massive disks that are dynamically hotter than low-mass disks. However, once a bar forms, it can easily buckle in the massive disks, where a deeper potential can sustain the vertical resonant orbits. We also find a probable buckling bar candidate (ESO 506−G004) that could provide further clues to understand the timescale of the buckling process.« less

A comparison of two soldering techniques on the misfit of bar-retained implant-supported overdentures.

PubMed

Alvarez, Angel; Lafita, Pedro; de Llanos, Hector; Gago, Angel; Brizuela, Aritza; Ellacuria, Joseba J

2014-02-01

This study was conducted to measure and compare the effect of the soldering method (torch soldering or ceramic furnace soldering) used for soldering bars to bar-retained, implant-supported overdentures on the fit between the bar gold cylinder and implant transgingival abutment. Thirty-two overdenture implant bars were manufactured and screw retained into two Bränemark implants, which were attached to a cow rib. The bars were randomly distributed in two groups: a torch-soldering group and a porcelain-furnace soldering group. Then all bars were cut and soldered using a torch and a ceramic furnace. The fit between the bar gold cylinders and implant transgingival abutments was measured with a light microscope on the opposite side to the screw tightening side before and after the bar soldering procedure. The data obtained were statistically processed for paired and independent data. The average misfit for all bars before soldering was 33.83 to 54.04 μm. After cutting and soldering the bars, the misfit increased up to a range of 71.74 to 78.79 μm. Both before and after the soldering procedure, the bars soldered using a torch showed a higher misfit when compared to the bars soldered using a porcelain furnace. After the soldering procedure, the misfit was slightly lower on the left side of the bars, which had been soldered using a ceramic furnace. According to our data, the soldering of bars using the torch or furnace oven soldering techniques does not improve the misfit of one-piece cast bars on two implants. The lower misfit was obtained using the porcelain furnace soldering technique. © 2013 by the American College of Prosthodontists.

Accuracy of System Step Response Roll Magnitude Estimation from Central and Peripheral Visual Displays and Simulator Cockpit Motion

NASA Technical Reports Server (NTRS)

Hosman, R. J. A. W.; Vandervaart, J. C.

1984-01-01

An experiment to investigate visual roll attitude and roll rate perception is described. The experiment was also designed to assess the improvements of perception due to cockpit motion. After the onset of the motion, subjects were to make accurate and quick estimates of the final magnitude of the roll angle step response by pressing the appropriate button of a keyboard device. The differing time-histories of roll angle, roll rate and roll acceleration caused by a step response stimulate the different perception processes related the central visual field, peripheral visual field and vestibular organs in different, yet exactly known ways. Experiments with either of the visual displays or cockpit motion and some combinations of these were run to asses the roles of the different perception processes. Results show that the differences in response time are much more pronounced than the differences in perception accuracy.

Supersonic aerodynamic characteristics of a maneuvering canard-controlled missile with fixed and free-rolling tail fins

NASA Technical Reports Server (NTRS)

Blair, A. B., Jr.

1990-01-01

Wind tunnel investigations were conducted on a generic cruciform canard-controlled missile configuration. The model featured fixed or free-rolling tail-fin afterbodies to provide an expanded aerodynamic data base with particular emphasis on alleviating large induced rolling moments and/or for providing canard roll control throughout the entire test angle-of-attack range. The tests were conducted in the NASA Langley Unitary Plan Wind Tunnel at Mach numbers from 2.50 to 3.50 at a constant Reynolds number per foot of 2.00 x 10 to the 6th. Selected test results are presented to show the effects of a fixed or free-rolling tail-fin afterbody on the static longitudinal and lateral-directional aerodynamic characteristics of a canard-controlled missile with pitch, yaw, and roll control at model roll angles of 0 deg and 45 deg.

Strip casting with fluxing agent applied to casting roll

DOEpatents

Williams, Robert S.; O'Malley, Ronald J.; Sussman, Richard C.

1997-01-01

A strip caster (10) for producing a continuous strip (24) includes a tundish (12) for containing a melt (14), a pair of horizontally disposed water cooled casting rolls (22) and devices (29) for electrostatically coating the outer peripheral chill surfaces (44) of the casting rolls with a powder flux material (56). The casting rolls are juxtaposed relative to one another for forming a pouting basin (18) for receiving the melt through a teeming tube (16) thereby establishing a meniscus (20) between the rolls for forming the strip. The melt is protected from the outside air by a non-oxidizing gas passed through a supply line (28) to a sealing chamber (26). A preferred flux is boron oxide having a melting point of about 550.degree. C. The flux coating enhances wetting of the steel melt to the casting roll and dissolves any metal oxide formed on the roll.

Method of texturing a superconductive oxide precursor

DOEpatents

DeMoranville, Kenneth L.; Li, Qi; Antaya, Peter D.; Christopherson, Craig J.; Riley, Jr., Gilbert N.; Seuntjens, Jeffrey M.

1999-01-01

A method of forming a textured superconductor wire includes constraining an elongated superconductor precursor between two constraining elongated members placed in contact therewith on opposite sides of the superconductor precursor, and passing the superconductor precursor with the two constraining members through flat rolls to form the textured superconductor wire. The method includes selecting desired cross-sectional shape and size constraining members to control the width of the formed superconductor wire. A textured superconductor wire formed by the method of the invention has regular-shaped, curved sides and is free of flashing. A rolling assembly for single-pass rolling of the elongated precursor superconductor includes two rolls, two constraining members, and a fixture for feeding the precursor superconductor and the constraining members between the rolls. In alternate embodiments of the invention, the rolls can have machined regions which will contact only the elongated constraining members and affect the lateral deformation and movement of those members during the rolling process.

Hot-rolling of reduced activation 8CrODS ferritic steel

NASA Astrophysics Data System (ADS)

Wu, Xiaochao; Ukai, Shigeharu; Leng, Bin; Oono, Naoko; Hayashi, Shigenari; Sakasegawa, Hideo; Tanigawa, Hiroyasu

2013-11-01

The 8CrODS ferritic steel is based on J1-lot developed for the advanced fusion blanket material to increase the coolant outlet temperature. A hot-rolling was conducted at the temperature above Ar3 of 716 °C, and its effect on the microstructure and tensile strength in 8CrODS ferritic steel was evaluated, comparing together with normalized and tempered specimen. It was confirmed that hot-rolling leads to slightly increased fraction of the ferrite and highly improved tensile strength. This ferrite was formed by transformation from the hot-rolled austenite during cooling due to fine austenite grains induced by hot-rolling. The coarsening of the transformed ferrite in hot-rolled specimen can be attributed to the crystalline rotation and coalescence of the similar oriented grains. The improved strength of hot-rolled specimen was ascribed to the high dislocation density and replacement of easily deformed martensite with the transformed coarse ferrite.

Rolled-up transformer structure for a radiofrequency integrated circuit (RFIC)

DOEpatents

Li, Xiuling; Huang, Wen

2016-05-03

A rolled-up transformer structure comprises a multilayer sheet having a rolled configuration comprising multiple turns about a longitudinal axis. The multilayer sheet comprises more than one conductive pattern layer on a strain-relieved layer, including a first conductive film and a second conductive film separated from the first conductive film in a thickness direction. The first conductive film comprises an even number of primary conductive strips, where each primary conductive strip has a length extending in the rolling direction, and the second conductive film comprises an even number of secondary conductive strips, where each secondary conductive strip has a length extending in the rolling direction. In the rolled configuration, turns of the primary conductive strips and turns of the secondary conductive strips wrap around the longitudinal axis. The primary conductive strips serve as a primary winding and the secondary conductive strips serve as a secondary winding of the rolled-up transformer structure.

Application of double laser interferometer in the measurement of translational stages' roll characteristics

NASA Astrophysics Data System (ADS)

Jin, Tao; Shen, Lu; Ke, Youlong; Hou, Wenmei; Ju, Aisong; Yang, Wei; Luo, Jialin

2016-10-01

In order to achieve rapid measurement of larger travel translation stages' roll-angle error in industry and to study the roll characteristics, this paper designs a small roll-angle measurement system based on laser heterodyne interferometry technology, test and researched on the roll characteristics of ball screw linear translation stage to fill the blank of the market. The results show that: during the operation of the ball screw linear translation stage, the workbench's roll angle changes complexly, its value is not only changing with different positions, but also shows different levels of volatility, what's more, the volatility varies with the workbench's work speed . Because of the non uniform stiffness of ball screw, at the end of each movement, the elastic potential energy being stored from the working process should release slowly, and the workbench will cost a certain time to roll fluctuate before it achieves a stable tumbling again.

Rolling-Element Fatigue Testing and Data Analysis - A Tutorial

NASA Technical Reports Server (NTRS)

Vlcek, Brian L.; Zaretsky, Erwin V.

2011-01-01

In order to rank bearing materials, lubricants and other design variables using rolling-element bench type fatigue testing of bearing components and full-scale rolling-element bearing tests, the investigator needs to be cognizant of the variables that affect rolling-element fatigue life and be able to maintain and control them within an acceptable experimental tolerance. Once these variables are controlled, the number of tests and the test conditions must be specified to assure reasonable statistical certainty of the final results. There is a reasonable correlation between the results from elemental test rigs with those results obtained with full-scale bearings. Using the statistical methods of W. Weibull and L. Johnson, the minimum number of tests required can be determined. This paper brings together and discusses the technical aspects of rolling-element fatigue testing and data analysis as well as making recommendations to assure quality and reliable testing of rolling-element specimens and full-scale rolling-element bearings.

Influences of rolling method on deformation force in cold roll-beating forming process

NASA Astrophysics Data System (ADS)

Su, Yongxiang; Cui, Fengkui; Liang, Xiaoming; Li, Yan

2018-03-01

In process, the research object, the gear rack was selected to study the influence law of rolling method on the deformation force. By the mean of the cold roll forming finite element simulation, the variation regularity of radial and tangential deformation was analysed under different rolling methods. The variation of deformation force of the complete forming racks and the single roll during the steady state under different rolling modes was analyzed. The results show: when upbeating and down beating, radial single point average force is similar, the tangential single point average force gap is bigger, the gap of tangential single point average force is relatively large. Add itionally, the tangential force at the time of direct beating is large, and the dire ction is opposite with down beating. With directly beating, deformation force loading fast and uninstall slow. Correspondingly, with down beating, deformat ion force loading slow and uninstall fast.

77 FR 13483 - Airworthiness Directives; Rolls-Royce plc (RR) Turbofan Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-07

... Directives; Rolls-Royce plc (RR) Turbofan Engines AGENCY: Federal Aviation Administration (FAA), DOT. ACTION... service information identified in this AD, contact Rolls-Royce plc, Corporate Communications, P.O. Box 31...), or, have Rolls-Royce plc revise Alert Service Bulletin (ASB) No. RB.211-72-AF964 to remove the...

76 FR 65136 - Airworthiness Directives; Rolls-Royce plc (RR) Turbofan Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-20

... Airworthiness Directives; Rolls-Royce plc (RR) Turbofan Engines AGENCY: Federal Aviation Administration (FAA... information identified in this AD, contact Rolls-Royce plc, Corporate Communications, P.O. Box 31, Derby...-166679 (76 FR 24793, May 3, 2011), and adding the following new AD: Rolls-Royce plc: Docket No. FAA-2010...

75 FR 77828 - Certain Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil: Extension of Time Limit...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-14

... DEPARTMENT OF COMMERCE International Trade Administration [C-351-829] Certain Hot-Rolled Flat-Rolled Carbon-Quality Steel Products From Brazil: Extension of Time Limit for Final Results of Countervailing Duty Administrative Review AGENCY: Import Administration, International Trade Administration, Department of Commerce DATES: Effective Date:...

14. VIEW OF METAL ROLLING OPERATION. THE METALS ARE BEING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

14. VIEW OF METAL ROLLING OPERATION. THE METALS ARE BEING PREPARED TO BE ROLLED INTO SHEETS OF SPECIFIC THICKNESS. COMPONENT PARTS WERE FABRICATED FROM THE METAL SHEETS. (11/82) - Rocky Flats Plant, Uranium Rolling & Forming Operations, Southeast section of plant, southeast quadrant of intersection of Central Avenue & Eighth Street, Golden, Jefferson County, CO

77 FR 6668 - Airworthiness Directives; Rolls-Royce plc Turbofan Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-09

... Airworthiness Directives; Rolls-Royce plc Turbofan Engines AGENCY: Federal Aviation Administration (FAA), DOT... all Rolls-Royce plc RB211-Trent 500 series turbofan engines. This AD requires a one-time inspection of... RB211- Trent 560A2-61 turbofan engines that have not complied with Rolls- Royce plc Service Bulletin No...

76 FR 35400 - Continuation of Suspended Antidumping Duty Investigation on Certain Hot-Rolled Flat-Rolled Carbon...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-17

... Russian Federation (``Russia'') would likely lead to continuation or recurrence of dumping, and material... duty investigation on hot- rolled steel from Russia (``the Agreement''), pursuant to section 751(c) of... the suspended antidumping duty investigation on hot- rolled steel from Russia would likely lead to a...

76 FR 7546 - Certain Hot-Rolled Carbon Steel Flat Products From Brazil: Rescission of Countervailing Duty...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-10

... Steel Flat Products From Brazil: Rescission of Countervailing Duty Administrative Review AGENCY: Import... hot- rolled carbon steel flat products (hot-rolled steel) from Brazil for the period January 1, 2009... countervailing duty order on hot-rolled steel from Brazil. See Agreement Suspending the Countervailing Duty...

Alternative Fuels Data Center: Michigan School Buses Get Rolling on Propane

Science.gov Websites

Michigan School Buses Get Rolling on Propane to someone by E-mail Share Alternative Fuels Data Center: Michigan School Buses Get Rolling on Propane on Facebook Tweet about Alternative Fuels Data Center: Michigan School Buses Get Rolling on Propane on Twitter Bookmark Alternative Fuels Data Center

76 FR 8319 - Special Conditions: Gulfstream Model GVI Airplane; Design Roll Maneuver Requirement for...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-14

... design features include an electronic flight control system that provides roll control of the airplane... Design Features The GVI is equipped with an electronic flight control system that provides roll control... condition at design maneuvering speed (V A ), in which the cockpit roll control is returned to neutral...

76 FR 65497 - Certain Hot-Rolled Carbon Steel Flat Products From India: Amended Final Results of Countervailing...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-21

... DEPARTMENT OF COMMERCE International Trade Administration [C-533-821] Certain Hot-Rolled Carbon...-rolled carbon steel flat products (HRCS) from India covering the January 1, 2006, through December 31... Certain Hot-Rolled Carbon Steel Flat Products from India: Final Results of Countervailing Duty...

78 FR 75371 - Diffusion-Annealed, Nickel-Plated Flat-Rolled Steel Products From Japan; Scheduling of the Final...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-11

...-Plated Flat-Rolled Steel Products From Japan; Scheduling of the Final Phase of an Antidumping... imports from Japan of diffusion-annealed, nickel- plated flat-rolled steel products, provided for... diffusion-annealed, nickel- plated flat-rolled steel products from Japan are being sold in the United States...

78 FR 23905 - Diffusion-Annealed, Nickel-Plated Flat-Rolled Steel Products From Japan: Initiation of...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-23

...-Plated Flat-Rolled Steel Products From Japan: Initiation of Antidumping Duty Investigation AGENCY: Import... products from Japan (``certain nickel-plated, flat-rolled steel''), filed in proper form by Thomas Steel... Antidumping Duty Petition on Diffusion-Annealed, Nickel- Plated Steel Flat-Rolled Products from Japan, dated...

76 FR 48143 - Certain Hot-Rolled Carbon Steel Flat Products From the People's Republic of China: Preliminary...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-08

... DEPARTMENT OF COMMERCE International Trade Administration [A-570-865] Certain Hot-Rolled Carbon... on certain hot- rolled carbon steel flat products (``hot-rolled'') from the People's Republic of... INFORMATION: Background On November 29, 2001, the Department published the antidumping duty order on hot...

76 FR 62039 - Certain Hot-Rolled Carbon Steel Flat Products From India: Final Results of 2009-2010 Antidumping...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-06

... DEPARTMENT OF COMMERCE International Trade Administration [A-533-820] Certain Hot-Rolled Carbon... administrative review of the antidumping duty order on certain hot-rolled carbon steel flat products from India (``hot-rolled steel'') manufactured by Ispat Industries Limited (``Ispat''), JSW Steel Limited (``JSW...

76 FR 2344 - Certain Hot-Rolled Carbon Steel Flat Products From India: Notice of Preliminary Results of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-13

... DEPARTMENT OF COMMERCE International Trade Administration [A-533-820] Certain Hot-Rolled Carbon... administrative review of the antidumping duty order on certain hot-rolled carbon steel flat products from India (``Indian Hot-Rolled'') manufactured by Essar Steel Limited (``Essar''), Ispat Industries Limited (``Ispat...

76 FR 42679 - Certain Hot-Rolled Carbon Steel Flat Products From India: Final Results of Antidumping Duty...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-19

... DEPARTMENT OF COMMERCE International Trade Administration [A-533-820] Certain Hot-Rolled Carbon... review of the antidumping duty order on certain hot- rolled carbon steel flat products from India... Preliminary Results \\2\\ of this review. \\2\\ See Certain Hot-Rolled Carbon Steel Flat Products From India...

76 FR 66901 - Certain Hot-Rolled Carbon Steel Flat Products From the People's Republic of China: Final...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-28

... DEPARTMENT OF COMMERCE International Trade Administration [A-570-865] Certain Hot-Rolled Carbon... of the administrative review of the antidumping duty order on certain hot-rolled carbon steel flat products (``hot-rolled'') from the People's Republic of China (``PRC'').\\1\\ This administrative review...

76 FR 31938 - Certain Hot-Rolled Carbon Steel Flat Products From India: Notice of Preliminary Results of 2009...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-02

... DEPARTMENT OF COMMERCE International Trade Administration [A-533-820] Certain Hot-Rolled Carbon... conducting an administrative review of the antidumping duty order on certain hot-rolled carbon steel flat products from India (``hot-rolled steel'') manufactured by Ispat Industries Limited (``Ispat''), JSW Steel...

77 FR 45576 - Certain Hot-Rolled Carbon Steel Flat Products From the People's Republic of China: Preliminary...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-01

... DEPARTMENT OF COMMERCE International Trade Administration [A-570-865] Certain Hot-Rolled Carbon...'') is conducting an administrative review of the antidumping duty order on certain hot- rolled carbon steel flat products (``hot-rolled steel'') from the People's Republic of China (``PRC''), covering the...

9 CFR 381.168 - Maximum percent of skin in certain poultry products.

Code of Federal Regulations, 2014 CFR

2014-01-01

..., when raw and when cooked. Table V Product name Percent skin Raw Cooked Boneless Turkey Breast or Boneless Turkey Breast Roll 14 Boneless Turkey Thigh or Boneless Turkey Thigh Roll 8 Boneless Turkey or Turkey Roll 15 Boneless Chicken Breast or Boneless Chicken Breast Roll 18 20 Boneless Chicken or Chicken...

9 CFR 381.168 - Maximum percent of skin in certain poultry products.

Code of Federal Regulations, 2012 CFR

2012-01-01

..., when raw and when cooked. Table V Product name Percent skin Raw Cooked Boneless Turkey Breast or Boneless Turkey Breast Roll 14 Boneless Turkey Thigh or Boneless Turkey Thigh Roll 8 Boneless Turkey or Turkey Roll 15 Boneless Chicken Breast or Boneless Chicken Breast Roll 18 20 Boneless Chicken or Chicken...

9 CFR 381.168 - Maximum percent of skin in certain poultry products.

Code of Federal Regulations, 2013 CFR

2013-01-01

..., when raw and when cooked. Table V Product name Percent skin Raw Cooked Boneless Turkey Breast or Boneless Turkey Breast Roll 14 Boneless Turkey Thigh or Boneless Turkey Thigh Roll 8 Boneless Turkey or Turkey Roll 15 Boneless Chicken Breast or Boneless Chicken Breast Roll 18 20 Boneless Chicken or Chicken...

49 CFR 661.12 - Certification requirement for procurement of buses, other rolling stock and associated equipment.

Code of Federal Regulations, 2014 CFR

2014-10-01

... AMERICA REQUIREMENTS § 661.12 Certification requirement for procurement of buses, other rolling stock and.... Certificate of Compliance with Buy America Rolling Stock Requirements The bidder or offeror hereby certifies... CFR 661.11. Date Signature Company Name Title Certificate of Non-Compliance with Buy America Rolling...

49 CFR 661.12 - Certification requirement for procurement of buses, other rolling stock and associated equipment.

Code of Federal Regulations, 2012 CFR

2012-10-01

... AMERICA REQUIREMENTS § 661.12 Certification requirement for procurement of buses, other rolling stock and.... Certificate of Compliance with Buy America Rolling Stock Requirements The bidder or offeror hereby certifies... CFR 661.11. Date Signature Company Name Title Certificate of Non-Compliance with Buy America Rolling...

49 CFR 661.12 - Certification requirement for procurement of buses, other rolling stock and associated equipment.

Code of Federal Regulations, 2011 CFR

2011-10-01

... AMERICA REQUIREMENTS § 661.12 Certification requirement for procurement of buses, other rolling stock and.... Certificate of Compliance with Buy America Rolling Stock Requirements The bidder or offeror hereby certifies... CFR 661.11. Date Signature Company Name Title Certificate of Non-Compliance with Buy America Rolling...

49 CFR 661.12 - Certification requirement for procurement of buses, other rolling stock and associated equipment.

Code of Federal Regulations, 2013 CFR

2013-10-01

... AMERICA REQUIREMENTS § 661.12 Certification requirement for procurement of buses, other rolling stock and.... Certificate of Compliance with Buy America Rolling Stock Requirements The bidder or offeror hereby certifies... CFR 661.11. Date Signature Company Name Title Certificate of Non-Compliance with Buy America Rolling...

Transient thermal stresses of work roll by coupled thermoelasticity

NASA Astrophysics Data System (ADS)

Lai, W. B.; Chen, T. C.; Weng, C. I.

1991-01-01

A numerical method, based on a two-dimensional plane strain model, is developed to predict the transient responses (that include distributions of temperature, thermal deformation, and thermal stress) of work roll during strip rolling by coupled thermoelasticity. The method consists of discretizing the space domain of the problem by finite element method first, and then treating the time domain by implicit time integration techniques. In order to avoid the difficulty in analysis due to relative movement between work roll and its thermal boundary, the energy equation is formulated with respect to a fixed Eulerian reference frame. The effect of thermoelastic coupling term, that is generally disregarded in strip rolling, can be considered and assessed. The influences of some important process parameters, such as rotational speed of the roll and intensity of heat flux, on transient solutions are also included and discussed. Furthermore, since the stress history at any point of the roll in both transient and steady state could be accurately evaluated, it is available to perform the analysis of thermal fatigue for the roll by means of previous data.

Research of thread rolling on difficult-to-cut material workpieces

NASA Astrophysics Data System (ADS)

Popov, A. Yu; Bugay, I. A.; Nazarov, P. V.; Evdokimova, O. P.; Popov, P. E.; Vasilyev, E. V.

2018-01-01

In medicine production Ti-6Al-4V Grade 5 alloys are used. One of the most important tasks is to increase the strength of the products and decrease in value. The possibility to roll special thread on Ti-6Al-4V Grade 5 alloy workpiece on 2-roller thread rolling machine has been studied. This is wrought alloy, treatment of which in cold condition causes difficulties due to low plasticity. To obtain Ti-6Al-4V Grade 5 alloy product with thread by rolling is rather difficult. This is due to large axial workpiece displacements resulting from large alloy resistance to cold plastic deformation. The provision of adequate kinematics requires experimental researches and the selection of modes - speed of rolling and pressure on the movable roller. The purpose of the work is to determine the optimal modes for rolling thread on titanium alloy workpiece. It has been stated that, after rolling, the product strength has increased up to 30%. As a result of the work, the unit has been made and recommendations to choose the optimal rolling process modes have been offered.

Ground roll attenuation by synchrosqueezed curvelet transform

NASA Astrophysics Data System (ADS)

Liu, Zhao; Chen, Yangkang; Ma, Jianwei

2018-04-01

Ground roll is a type of coherent noise in land seismic data that has low frequency, low velocity and high amplitude. It damages reflection events that contain important information about subsurface structures, hence the removal of ground roll is a crucial step in seismic data processing. A suitable transform is needed for removal of ground roll. Curvelet transform is an effective sparse transform that optimally represents seismic events. In addition, the curvelets can provide a multiscale and multidirectional decomposition of the input data in time-frequency and angular domain, which can help distinguish between ground roll and useful signals. In this paper, we apply synchrosqueezed curvelet transform (SSCT) for ground roll attenuation. The synchrosqueezing technique in SSCT is used to precisely reallocate the energy of local wave vectors in order to separate ground roll from the original data with higher resolution and higher fidelity. Examples of synthetic and field seismic data reveal that SSCT performs well in the suppression of aliased and non-aliased ground roll while preserving reflection waves, in comparison with high-pass filtering, wavelet and curvelet methods.

Inflation with a constant rate of roll

DOE Office of Scientific and Technical Information (OSTI.GOV)

Motohashi, Hayato; Starobinsky, Alexei A.; Yokoyama, Jun'ichi, E-mail: motohashi@kicp.uchicago.edu, E-mail: alstar@landau.ac.ru, E-mail: yokoyama@resceu.s.u-tokyo.ac.jp

2015-09-01

We consider an inflationary scenario where the rate of inflaton roll defined by {sup ··}φ/H φ-dot remains constant. The rate of roll is small for slow-roll inflation, while a generic rate of roll leads to the interesting case of 'constant-roll' inflation. We find a general exact solution for the inflaton potential required for such inflaton behaviour. In this model, due to non-slow evolution of background, the would-be decaying mode of linear scalar (curvature) perturbations may not be neglected. It can even grow for some values of the model parameter, while the other mode always remains constant. However, this always occurs formore » unstable solutions which are not attractors for the given potential. The most interesting particular cases of constant-roll inflation remaining viable with the most recent observational data are quadratic hilltop inflation (with cutoff) and natural inflation (with an additional negative cosmological constant). In these cases even-order slow-roll parameters approach non-negligible constants while the odd ones are asymptotically vanishing in the quasi-de Sitter regime.« less

Large Area 2D and 3D Colloidal Photonic Crystals Fabricated by a Roll-to-Roll Langmuir-Blodgett Method.

PubMed

Parchine, Mikhail; McGrath, Joe; Bardosova, Maria; Pemble, Martyn E

2016-06-14

We present our results on the fabrication of large area colloidal photonic crystals on flexible poly(ethylene terephthalate) (PET) film using a roll-to-roll Langmuir-Blodgett technique. Two-dimensional (2D) and three-dimensional (3D) colloidal photonic crystals from silica nanospheres (250 and 550 nm diameter) with a total area of up to 340 cm(2) have been fabricated in a continuous manner compatible with high volume manufacturing. In addition, the antireflective properties and structural integrity of the films have been enhanced via the use of a second roll-to-roll process, employing a slot-die coating of an optical adhesive over the photonic crystal films. Scanning electron microscopy images, atomic force microscopy images, and UV-vis optical transmission and reflection spectra of the fabricated photonic crystals are analyzed. This analysis confirms the high quality of the 2D and 3D photonic crystals fabricated by the roll-to-roll LB technique. Potential device applications of the large area 2D and 3D colloidal photonic crystals on flexible PET film are briefly reviewed.

Experimental research on micro-pit defects of SUS 430 stainless steel strip in cold rolling process

NASA Astrophysics Data System (ADS)

Li, Changsheng; Li, Miao; Zhu, Tao; Huo, Gang

2013-05-01

In order to improve surface glossiness of stainless steel strip in tandem cold rolling, experimental research on micro-pit defects of SUS 430 ferrite stainless steel was investigated in laboratory. The surface morphology of micro-pit defects was observed by SEM. The effects of micro-pit defects on rolling reduction, roll surface roughness and emulsion parameters were analyzed. With the pass number increasing, the quantity and surface of micro-pit defects were reduced, uneven peak was decreased and gently along rolling direction, micro-pit defects had equally distributed tendency along tranverse direction. The micro-pit defects were increased with the roll surface roughness increase. The defects ratio was declined with larger gradient at pass number 1 to 3, but gentle slope at pass number 4 to 5. The effects of temperature 55° and 63°, concentration 3% and 6% of emulsion on micro-pit effects had not obvious difference. Maintain of micro-pit was effected by rolling oil or air in the micro-pit, the quality of oil was much more than the air in the micro-pit in lubrication rolling.

Closure behavior of spherical void in slab during hot rolling process

NASA Astrophysics Data System (ADS)

Cheng, Rong; Zhang, Jiongming; Wang, Bo

2018-04-01

The mechanical properties of steels are heavily deteriorated by voids. The influence of voids on the product quality should be eliminated through rolling processes. The study on the void closure during hot rolling processes is necessary. In present work, the closure behavior of voids at the center of a slab at 800 °C during hot rolling processes has been simulated with a 3D finite element model. The shape of the void and the plastic strain distribution of the slab are obtained by this model. The void decreases along the slab thickness direction and spreads along the rolling direction but hardly changes along the strip width direction. The relationship between closure behavior of voids and the plastic strain at the center of the slab is analyzed. The effects of rolling reduction, slab thickness and roller diameter on the closure behavior of voids are discussed. The larger reduction, thinner slab and larger roller diameter all improve the closure of voids during hot rolling processes. Experimental results of the closure behavior of a void in the slab during hot rolling process mostly agree with the simulation results..

Finite element simulation and comparison of a shear strain and equivalent strain during ECAP and asymmetric rolling

NASA Astrophysics Data System (ADS)

Pesin, A.; Pustovoytov, D.; Shveyova, T.; Vafin, R.

2017-12-01

The level of a shear strain and equivalent strain plays a key role in terms of the possibility of using the asymmetric rolling process as a method of severe plastic deformation. Strain mode (pure shear or simple shear) can affect very strongly on the equivalent strain and the grain refinement of the material. This paper presents the results of FEM simulations and comparison of the equivalent strain in the aluminium alloy 5083 processed by a single-pass equal channel angular pressing (simple shear), symmetric rolling (pure shear) and asymmetric rolling (simultaneous pure and simple shear). The nonlinear effect of rolls speed ratio on the deformation characteristics during asymmetric rolling was found. Extremely high equivalent strain up to e=4.2 was reached during a single-pass asymmetric rolling. The influence of the shear strain on the level of equivalent strain is discussed. Finite element analysis of the deformation characteristics, presented in this study, can be used for optimization of the asymmetric rolling process as a method of severe plastic deformation.

PSL Icing Facility Upgrade Overview

NASA Technical Reports Server (NTRS)

Griffin, Thomas A.; Dicki, Dennis J.; Lizanich, Paul J.

2014-01-01

The NASA Glenn Research Center Propulsion Systems Lab (PSL) was recently upgraded to perform engine inlet ice crystal testing in an altitude environment. The system installed 10 spray bars in the inlet plenum for ice crystal generation using 222 spray nozzles. As an altitude test chamber, the PSL is capable of simulating icing events at altitude in a groundtest facility. The system was designed to operate at altitudes from 4,000 to 40,000 ft at Mach numbers up to 0.8M and inlet total temperatures from -60 to +15 degF. This paper and presentation will be part of a series of presentations on PSL Icing and will cover the development of the icing capability through design, developmental testing, installation, initial calibration, and validation engine testing. Information will be presented on the design criteria and process, spray bar developmental testing at Cox and Co., system capabilities, and initial calibration and engine validation test. The PSL icing system was designed to provide NASA and the icing community with a facility that could be used for research studies of engine icing by duplicating in-flight events in a controlled ground-test facility. With the system and the altitude chamber we can produce flight conditions and cloud environments to simulate those encountered in flight. The icing system can be controlled to set various cloud uniformities, droplet median volumetric diameter (MVD), and icing water content (IWC) through a wide variety of conditions. The PSL chamber can set altitudes, Mach numbers, and temperatures of interest to the icing community and also has the instrumentation capability of measuring engine performance during icing testing. PSL last year completed the calibration and initial engine validation of the facility utilizing a Honeywell ALF502-R5 engine and has duplicated in-flight roll back conditions experienced during flight testing. This paper will summarize the modifications and buildup of the facility to accomplish these tests.

Letter Report Documenting Progress of Second Generation ATF FeCrAl Alloy Fabrication

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yamamoto, Y.; Yang, Y.; Field, K. G.

2014-06-10

Development of the 2nd generation ATF FeCrAl alloy has been initiated, and a candidate alloy was selected for trial tube fabrication through hot-extrusion and gun-drilling processes. Four alloys based on Fe-13Cr-4.5Al-0.15Y in weight percent were newly cast with minor alloying additions of Mo, Si, Nb, and C to promote solid-solution and second-phase precipitate strengthening. The alloy compositions were selected with guidance from computational thermodynamic tools. The lab-scale heats of ~ 600g were arc-melted and drop-cast, homogenized, hot-forged and -rolled, and then annealed producing plate shape samples. An alloy with Mo and Nb additions (C35MN) processed at 800°C exhibits very finemore » sub-grain structure with the sub-grain size of 1-3μm which exhibited more than 25% better yield and tensile strengths together with decent ductility compared to the other FeCrAl alloys at room temperature. It was found that the Nb addition was key to improving thermal stability of the fine sub-grain structure. Optimally, grains of less than 30 microns are desired, with grains up to and order of magnitude in desired produced through Nb addition. Scale-up effort of the C35MN alloy was made in collaboration with a commercial cast company who has a capability of vacuum induction melting. A 39lb columnar ingot with ~81mm diameter and ~305mm height (with hot-top) was commercially cast, homogenized, hot-extruded, and annealed providing 10mm-diameter bar-shape samples with the fine sub-grain structure. This commercial heat proved consistent with materials produced at ORNL at the lab-scale. Tubes and end caps were machined from the bar sample and provided to another work package for the ATF-1 irradiation campaign in the milestone M3FT-14OR0202251.« less

Numerical analysis of the flexible roll forming of an automotive component from high strength steel

NASA Astrophysics Data System (ADS)

Abeyrathna, B.; Abvabi, A.; Rolfe, B.; Taube, R.; Weiss, M.

2016-11-01

Conventional roll forming is limited to components with uniform cross-section; the recently developed flexible roll forming (FRF) process can be used to form components which vary in both width and depth. It has been suggested that this process can be used to manufacture automotive components from Ultra High Strength Steel (UHSS) which has limited tensile elongation. In the flexible roll forming process, the pre-cut blank is fed through a set of rolls; some rolls are computer-numerically controlled (CNC) to follow the 3D contours of the part and hence parts with a variable cross-section can be produced. This paper introduces a new flexible roll forming technique which can be used to form a complex shape with the minimum tooling requirements. In this method, the pre-cut blank is held between two dies and the whole system moves back and forth past CNC forming rolls. The forming roll changes its angle and position in each pass to incrementally form the part. In this work, the process is simulated using the commercial software package Copra FEA. The distribution of total strain and final part quality are investigated as well as related shape defects observed in the process. Different tooling concepts are used to improve the strain distribution and hence the part quality.

Rolling Process Modeling Report. Finite-Element Model Validation and Parametric Study on various Rolling Process parameters

DOE Office of Scientific and Technical Information (OSTI.GOV)

Soulami, Ayoub; Lavender, Curt A.; Paxton, Dean M.

2015-06-15

Pacific Northwest National Laboratory (PNNL) has been investigating manufacturing processes for the uranium-10% molybdenum alloy plate-type fuel for high-performance research reactors in the United States. This work supports the U.S. Department of Energy National Nuclear Security Administration’s Office of Material Management and Minimization Reactor Conversion Program. This report documents modeling results of PNNL’s efforts to perform finite-element simulations to predict roll-separating forces for various rolling mill geometries for PNNL, Babcock & Wilcox Co., Y-12 National Security Complex, Los Alamos National Laboratory, and Idaho National Laboratory. The model developed and presented in a previous report has been subjected to further validationmore » study using new sets of experimental data generated from a rolling mill at PNNL. Simulation results of both hot rolling and cold rolling of uranium-10% molybdenum coupons have been compared with experimental results. The model was used to predict roll-separating forces at different temperatures and reductions for five rolling mills within the National Nuclear Security Administration Fuel Fabrication Capability project. This report also presents initial results of a finite-element model microstructure-based approach to study the surface roughness at the interface between zirconium and uranium-10% molybdenum.« less

Rolling Maneuver Load Alleviation using active controls

NASA Technical Reports Server (NTRS)

Woods-Vedeler, Jessica A.; Pototzky, Anthony S.

1992-01-01

Rolling Maneuver Load Alleviation (RMLA) has been demonstrated on the Active Flexible Wing (AFW) wind tunnel model in the NASA Langley Transonic Dynamics Tunnel. The design objective was to develop a systematic approach for developing active control laws to alleviate wing incremental loads during roll maneuvers. Using linear load models for the AFW wind-tunnel model which were based on experimental measurements, two RMLA control laws were developed based on a single-degree-of-freedom roll model. The RMLA control laws utilized actuation of outboard control surface pairs to counteract incremental loads generated during rolling maneuvers and actuation of the trailing edge inboard control surface pairs to maintain roll performance. To evaluate the RMLA control laws, roll maneuvers were performed in the wind tunnel at dynamic pressures of 150, 200, and 250 psf and Mach numbers of 0.33, .38 and .44, respectively. Loads obtained during these maneuvers were compared to baseline maneuver loads. For both RMLA controllers, the incremental torsion moments were reduced by up to 60 percent at all dynamic pressures and performance times. Results for bending moment load reductions during roll maneuvers varied. In addition, in a multiple function test, RMLA and flutter suppression system control laws were operated simultaneously during roll maneuvers at dynamic pressures 11 percent above the open-loop flutter dynamic pressure.

Abrasive rolling effects on material removal and surface finish in chemical mechanical polishing analyzed by molecular dynamics simulation

NASA Astrophysics Data System (ADS)

Si, Lina; Guo, Dan; Luo, Jianbin; Lu, Xinchun; Xie, Guoxin

2011-04-01

In an abrasive chemical mechanical polishing (CMP) process, materials were considered to be removed by abrasive sliding and rolling. Abrasive sliding has been investigated by many molecular dynamics (MD) studies; while abrasive rolling was usually considered to be negligible and therefore was rarely investigated. In this paper, an MD simulation was used to study the effects of abrasive rolling on material removal and surface finish in the CMP process. As the silica particle rolled across the silicon substrate, some atoms of the substrate were dragged out from their original positions and adhered to the silica particle, leaving some atomic vacancies on the substrate surface. Meanwhile, a high quality surface could be obtained. During the abrasive rolling process, the influencing factors of material removal, e.g., external down force and driving force, were also discussed. Finally, MD simulations were carried out to examine the effects of abrasive sliding on material removal under the same external down force as abrasive rolling. The results showed that the ability of abrasive rolling to remove material on the atomic scale was not notably inferior to that of abrasive sliding. Therefore, it can be proposed that both abrasive sliding and rolling play important roles in material removal in the abrasive CMP of the silicon substrate.

Some Effects of Roll Rate on the Longitudinal Stability Characteristics of a Cruciform Missile Configuration as Determined from Flight Test for a Mach Number Range of 1.1 to 1.8

NASA Technical Reports Server (NTRS)

Barber, H. T., Jr.; Lundstrom, R. R.

1956-01-01

A model of a cruciform missile configuration having a low-aspectratio wing equipped with flap-type controls was flight tested in order to determine stability and control characteristics while rolling at about 5 radians per second. Comparison is made with results from a similar model which rolled at a much lower rate. Results showed that, if the ratio of roll rate to natural circular frequency in pitch is not greater than about 0.3, the motion following a step disturbance in pitch essentially remains in a plane in space. The slope of normal-force coefficient against angle of attack C(sub N(sub A)) was the same as for the slowly rolling model at O deg control deflection but C(sub N(sub A)) was much higher for the faster rolling model at about 5 deg control deflection. The slope of pitching-moment coefficient against angle of attack & same for both models at 0 deg control deflection but was lower for the faster rolling model at about 5 deg control deflection. Damping data for the faster rolling model showed considerably more scatter than for the slowly rolling model.

A method for the determination of the coefficient of rolling friction using cycloidal pendulum

NASA Astrophysics Data System (ADS)

Ciornei, M. C.; Alaci, S.; Ciornei, F. C.; Romanu, I. C.

2017-08-01

The paper presents a method for experimental finding of coefficient of rolling friction appropriate for biomedical applications based on the theory of cycloidal pendulum. When a mobile circle rolls over a fixed straight line, the points from the circle describe trajectories called normal cycloids. To materialize this model, it is sufficient that a small region from boundary surfaces of a moving rigid body is spherical. Assuming pure rolling motion, the equation of motion of the cycloidal pendulum is obtained - an ordinary nonlinear differential equation. The experimental device is composed by two interconnected balls rolling over the material to be studied. The inertial characteristics of the pendulum can be adjusted via weights placed on a rod. A laser spot oscillates together to the pendulum and provides the amplitude of oscillations. After finding the experimental parameters necessary in differential equation of motion, it can be integrated using the Runge-Kutta of fourth order method. The equation was integrated for several materials and found values of rolling friction coefficients. Two main conclusions are drawn: the coefficient of rolling friction influenced significantly the amplitude of oscillation but the effect upon the period of oscillation is practically imperceptible. A methodology is proposed for finding the rolling friction coefficient and the pure rolling condition is verified.

Efficacy of the “pick and roll” offense in top level European basketball teams

PubMed Central

Marmarinos, Christos; Kostopoulos, Nikolaos; Apostolidis, Alexandros

2016-01-01

Abstract Team offense in basketball games consists of a set of offensive actions carried out with the cooperation of two or more players. Of these actions, the most commonly used in the last decade is the on-ball screen called the “pick and roll.” The aim of this study was to analyze all of the pick and rolls conducted in the Euroleague championship from all of the 24 participating teams and to investigate the possible relationships between success in the pick and roll and overall success of the teams. For this purpose, 12,376 pick and rolls from 502 matches were analyzed and classified in categories according to the end result of the offensive possession. The results showed that the most effective type of pick and roll offense was when a shot was attempted after 2 passes from the pick and roll occurrence, followed by the screener’s shot when he rolled to the basket. Additionally, linear regression analysis confirmed that pick and roll effectiveness could predict the final classification of the teams. Conclusively, coaches of the high level European clubs should focus on training the players to the most efficient phases of the pick and roll offense, so that the chances of winning the championship to be maximized. PMID:28149375

Multilength Scale Patterning of Functional Layers by Roll-to-Roll Ultraviolet-Light-Assisted Nanoimprint Lithography.

PubMed

Leitgeb, Markus; Nees, Dieter; Ruttloff, Stephan; Palfinger, Ursula; Götz, Johannes; Liska, Robert; Belegratis, Maria R; Stadlober, Barbara

2016-05-24

Top-down fabrication of nanostructures with high throughput is still a challenge. We demonstrate the fast (>10 m/min) and continuous fabrication of multilength scale structures by roll-to-roll UV-nanoimprint lithography on a 250 mm wide web. The large-area nanopatterning is enabled by a multicomponent UV-curable resist system (JRcure) with viscous, mechanical, and surface properties that are tunable over a wide range to either allow for usage as polymer stamp material or as imprint resist. The adjustable elasticity and surface chemistry of the resist system enable multistep self-replication of structured resist layers. Decisive for defect-free UV-nanoimprinting in roll-to-roll is the minimization of the surface energies of stamp and resist, and the stepwise reduction of the stiffness from one layer to the next is essential for optimizing the reproduction fidelity especially for nanoscale features. Accordingly, we demonstrate the continuous replication of 3D nanostructures and the high-throughput fabrication of multilength scale resist structures resulting in flexible polyethylenetherephtalate film rolls with superhydrophobic properties. Moreover, a water-soluble UV-imprint resist (JRlift) is introduced that enables residue-free nanoimprinting in roll-to-roll. Thereby we could demonstrate high-throughput fabrication of metallic patterns with only 200 nm line width.

Tropical Cyclone Boundary Layer Rolls in Synthetic Aperture Radar Imagery

NASA Astrophysics Data System (ADS)

Huang, Lanqing; Li, Xiaofeng; Liu, Bin; Zhang, Jun A.; Shen, Dongliang; Zhang, Zenghui; Yu, Wenxian

2018-04-01

Marine atmospheric boundary layer (MABL) roll plays an important role in the turbulent exchange of momentum, sensible heat, and moisture throughout MABL of tropical cyclone (TC). Hence, rolls are believed to be closely related to TC's development, intensification, and decay processes. Spaceborne synthetic aperture radar (SAR) provides a unique capability to image the sea surface imprints of quasi-linear streaks induced by the MABL rolls within a TC. In this study, sixteen SAR images, including three images acquired during three major hurricanes: Irma, Jose, and Maria in the 2017 Atlantic hurricane season, were utilized to systematically map the distribution and wavelength of MABL rolls under the wide range of TC intensities. The images were acquired by SAR onboard RADARSAT-1/2, ENVISAT, and SENTINEL-1 satellites. Our findings are in agreement with the previous one case study of Hurricane Katrina (2005), showing the roll wavelengths are between 600 and 1,600 m. We also find that there exist roll imprints in eyewall and rainbands, although the boundary layer heights are shallower there. Besides, the spatial distribution of roll wavelengths is asymmetrical. The roll wavelengths are found to be the shortest around the storm center, increase and then decrease with distance from storm center, reaching the peak values in the range of d∗-2d∗, where d∗ is defined as the physical location to TC centers normalized by the radius of maximum wind. These MABL roll characteristics cannot be derived using conventional aircraft and land-based Doppler radar observations.

Effects of alignment on the roll-over shapes of prosthetic feet.

PubMed

Hansen, Andrew

2008-12-01

Recent work suggests that a prosthetic ankle-foot component's roll-over shape - the effective rocker it conforms to between initial contact and opposite initial contact (the 'roll-over' interval of walking) - is closely linked to its final alignment in the prosthesis (as determined by a skilled prosthetist using heuristic techniques). If true, this information may help to determine the appropriate alignment for a lower limb prosthesis before it is built, or a priori. Knowledge is needed for future models that will incorporate the roll-over shape including the relative effect of alignment on the roll-over shape's radius of curvature and arc length. The purpose of this study was to evaluate the hypotheses that: (i) Changes in prosthesis alignment alter the position and orientation of a foot's roll-over shape in prosthesis-based coordinates, and (ii) these changes occur without changing the radius of curvature or arc length of the roll-over shape. To examine the hypotheses, this study examined the effects of nine alignment settings on the roll-over shapes of two prosthetic feet. The idea that alignment changes move and rotate roll-over shapes of prosthetic feet in prosthesis coordinates is supported by this work, but the hypothesis that the radius of curvature and arc length do not change for different alignments is not strongly supported by the data. A revised approach is presented that explains some of the changes to the roll-over shape parameters due to changes in rotational alignment.

Using Rolling to Develop Neuromuscular Control and Coordination of the Core and Extremities of Athletes

PubMed Central

Voight, Michael L.; Cook, Gray; Gill, Lance

2009-01-01

Rolling is a movement pattern seldom used by physical therapists for assessment and intervention with adult clientele with normal neurologic function. Rolling, as an adult motor skill, combines the use of the upper extremities, core, and lower extremities in a coordinated manner to move from one posture to another. Rolling is accomplished from prone to supine and supine to prone, although the method by which it is performed varies among adults. Assessment of rolling for both the ability to complete the task and bilateral symmetry may be beneficial for use with athletes who perform rotationally-biased sports such as golf, throwing, tennis, and twisting sports such as dance, gymnastics, and figure skating. Additionally, when used as intervention techniques, the rolling patterns have the ability to affect dysfunction of the upper quarter, core, and lower quarter. By applying proprioceptive neuromuscular facilitation (PNF) principles, the therapist may assist patients and clients who are unable to complete a rolling pattern. Examples given in the article include distraction/elongation, compression, and manual contacts to facilitate proper rolling. The combined experience of the four authors is used to describe techniques for testing, assessment, and treatment of dysfunction, using case examples that incorporate rolling. The authors assert that therapeutic use of the developmental pattern of rolling with techniques derived from PNF is a hallmark in rehabilitation of patients with neurologic dysfunction, but can be creatively and effectively utilized in musculoskeletal rehabilitation. PMID:21509112

Social Organization in Bars: Implications for Tobacco Control Policy

PubMed Central

Lee, Juliet P.; Antin, Tamar M.J.; Moore, Roland S.

2011-01-01

This paper considers social roles and relationships of the patrons, staff and owners of bars as critical factors determining adherence to public health policies, and specifically California’s smokefree workplace law. Specific elements of social organization in bars affecting health policy include the community within which the bar is set, the unique identity the bar creates, the bar staff and patrons who enact this identity, and their bar society. These elements were found to contribute to the development of power relations within the bar and solidarity against the outside world, resulting in either resistance to or compliance with smokefree workplace policy. PMID:22522904

Stability of Heavy Tetraquarks

NASA Astrophysics Data System (ADS)

Valcarce, A.; Vijande, J.; Richard, J.-M.; Garcilazo, H.

2018-03-01

We discuss the stability of tetraquark systems with two different masses. After some reminders about the stability of very asymmetric QQ{\\bar{q}} {\\bar{q}} tetraquarks, we demonstrate that in the all-heavy limit q → Q, the system becomes unstable for standard color-additive models. We also analyze the consequences of symmetry breaking for Qq{\\bar{Q}}{\\bar{q}} configurations: we find a kind of metastability between the lowest threshold Q{\\bar{Q}} + q{\\bar{q}} and the highest one, Q{\\bar{q}}+{\\bar{Q}} q, and we calculate the width of the resonance. Our results are consistent with the experimental observation of narrow hadrons lying well above their lowest decay threshold.

Closed membrane shapes with attached BAR domains subject to external force of actin filaments.

PubMed

Mesarec, Luka; Góźdź, Wojciech; Iglič, Veronika Kralj; Kralj, Samo; Iglič, Aleš

2016-05-01

Membrane deformations induced by attached BAR superfamily domains could trigger or facilitate the growth of plasma membrane protrusions. The BAR domain family consists of BAR, F-BAR and I-BAR domains, each enforcing a different local curvature when attached to the membrane surface. Our theoretical study mainly focuses on the role of I-BAR in the membrane tubular deformations generated or stabilised by actin filaments. The influence of the area density of membrane attached BAR domains and their intrinsic curvature on the closed membrane shapes (vesicles) was investigated numerically. We derived an analytical approximative expression for the critical relative area density of BARs at which the membrane tubular protrusions on vesicles are most prominent. We have shown that the BARs with a higher intrinsic curvature induce thinner and longer cylindrical protrusions. The average orientation of the membrane attached BARs is altered when the vesicle shape is subjected to external force of growing actin rod-like structure inside a vesicle. The average orientation angle of membrane attached BARs may indicate whether the actin filaments are just stabilising the protrusion or generating it by stretching the vesicle. Copyright © 2016 Elsevier B.V. All rights reserved.

Improved Kolsky tension bar for high-rate tensile characterization of materials

NASA Astrophysics Data System (ADS)

Song, Bo; Antoun, Bonnie R.; Connelly, Kevin; Korellis, John; Lu, Wei-Yang

2011-04-01

A new Kolsky tension bar has been re-designed and developed at Sandia National Laboratories, CA. The new design uses the concept that a solid striker is fired to impact an end cap attached to the open end of the gun barrel to generate dynamic tensile loading. The gun barrel here serves as part of the loading device. The incident bar that is connected to the gun barrel and the transmission bar follow the design similar to the Kolsky compression bar. The bar supporting and aligning systems are the same as those in the Kolsky compression bar design described by Song et al (2009 Meas. Sci. Technol. 20 115701). Due to the connection complication among the gun barrel, bars and specimen, stress-wave propagation in the new Kolsky tension bar system is comprehensively analyzed. Based on the stress-wave analysis, the strain gage location on the incident bar needs to be carefully determined. A highly precise laser-beam measurement system is recommended to directly measure the displacement of the incident bar end. Dynamic tensile characterization of a 4330-V steel using this new Kolsky tension bar is presented as an example.

Photosystem II functionality and antioxidant system changes during leaf rolling in post-stress emerging Ctenanthe setosa exposed to drought.

PubMed

Terzi, Rabiye; Saruhan, Neslihan; Sağlam, A; Nar, Hatice; Kadioğlu, A

2009-12-01

We studied the changes in antioxidant system and chlorophyll fluorescence parameters in post-stress emerging Ctenanthe setosa (Rosc.) Eichler (Marantaceae) plants (PSE plants) having reduced leaf area under drought stress causing leaf rolling and re-watering. PSE plants were compared to primary stressed plants (PS) in previous studies. The parameters were measured at different visual leaf rolling scores from 1 to 4 (1 is unrolled, 4 is tightly rolled and the others is intermediate form). Water potentials and stomatal conductance of leaves were gradually decreased during leaf rolling. Similarly, maximum quantum efficiency of open PS II center and quantum yield of PS II decreased during the rolling period. Non-photochemical quenching of chlorophyll fluorescence decreased at score 2 then increased while photochemical quenching did not change during leaf rolling. Electron transport rate decreased only at score 4 but approximately reached to score 1 level after re-watering. Superoxide dismutase activity was not constant at all leaf rolling scores. Ascorbate peroxidase, catalase and glutathione reductase activities generally tended to increase during leaf rolling. Lipid peroxidation and H 2 O 2 content increased at score 2 but decreased at the later scores. On the other hand, O 2 .- production increased during the rolling period. After re-watering of the plants having score 4 of leaf rolling, antioxidant enzyme activities were lower than those of score 1. Other physiological parameters also tended to reach the value of score 1. The results indicated that PSE plants gained drought tolerance by reducing leaf area effectively induced their antioxidant systems and protected the photosynthesis under drought stress similar to PS plants.

Texture evolution and mechanical anisotropy of biomedical hot-rolled Co-Cr-Mo alloy.

PubMed

Mori, Manami; Yamanaka, Kenta; Sato, Shigeo; Chiba, Akihiko

2015-11-01

Crystallographic textures and their effect on the mechanical anisotropy of a hot-rolled biomedical Co-Cr-Mo alloy were investigated. The hot-rolled Co-28Cr-6Mo-0.13N (mass%) alloy examined here exhibited a monotonic strength increment following hot-rolling reduction, eventually reaching a 0.2% proof stress of 1400 MPa while maintaining acceptable ductility (>10%). The dominant hot-rolling texture was a brass-type component, which is characterized by the alloy's peculiarly low stacking fault energy (SFE) even at hot rolling temperatures, although the minor peaks of the near copper component were also identified. However, because of the onset of dynamic recrystallization (DRX) during the hot rolling process, the texture intensity was relatively weak even after 90% hot rolling, although the grain refinement originating from the DRX was not significant (the "less active DRX" condition increased the strain accumulation during the process, resulting in high-strength samples). The weakened texture development resulted in negligible in-plane anisotropy for the hot-rolled specimen strength, when the specimens were tensile strained in the rolling direction (RD) and transverse direction (TD). The elongation-to-failure, however, exhibited a difference with respect to the tensile loading axis. It is suggested that the ductility anisotropy is closely related to a strain-induced γ (fcc) → ε (hcp) martensitic transformation during tensile loading, resulting in a difference in the proportion of quasi-cleavage fracture surfaces. The obtained results will be helpful in the development of high-strength Co-Cr-Mo alloy plates and sheets, and have implications regarding plastic deformation and texture evolution during the hot rolling of non-conventional metallic materials with low SFE at elevated temperatures, where planar dislocation slips of Shockley partial dislocations and thermally activated process interplay. Copyright © 2015 Elsevier Ltd. All rights reserved.

The relation between cigarette price and hand-rolling tobacco consumption in the UK: an ecological study.

PubMed

Rothwell, Lucas; Britton, John; Bogdanovica, Ilze

2015-06-15

Cigarette price increases reduce smoking prevalence but as a tobacco control policy are undermined by the availability of lower cost alternatives such as hand-rolling tobacco. The aim of this descriptive study is to explore time trends in the price of manufactured cigarettes and hand-rolling tobacco, and in the numbers of people who smoke these products, over recent years in the UK. UK. Trends in the most popular price category (MPPC) data for cigarettes and hand-rolling tobacco from 1983 to 2012 adjusted for inflation using the Retail Price Index, and trends in smoking prevalence and the proportion of smokers using hand-rolling tobacco from 1974 to 2010. After adjustment for inflation, there was an increase in prices of manufactured cigarettes and hand-rolling tobacco between 1983 and 2012. Between 1974 and 2010, the prevalence of smoking fell from 45% to 20%, and the estimated total number of smokers from 25.3 to 12.4 million. However the number of people smoking hand-rolling tobacco increased from 1.4 to 3.2 million, and MPPC cigarette price was strongly correlated with number of people smoking hand-rolling tobacco. Although the ecological study design precludes conclusions on causality, the association between increases in manufactured cigarette price and the number of people smoking hand-rolling tobacco suggests that the lower cost of smoking hand-rolling tobacco encourages downtrading when cigarette prices rise. The magnitude of this association indicates that the lower cost of hand-rolling tobacco seriously undermines the use of price as a tobacco control measure. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Conical Euler simulation and active suppression of delta wing rocking motion

NASA Technical Reports Server (NTRS)

Lee, Elizabeth M.; Batina, John T.

1990-01-01

A conical Euler code was developed to study unsteady vortex-dominated flows about rolling highly-swept delta wings, undergoing either forced or free-to-roll motions including active roll suppression. The flow solver of the code involves a multistage Runge-Kutta time-stepping scheme which uses a finite volume spatial discretization of the Euler equations on an unstructured grid of triangles. The code allows for the additional analysis of the free-to-roll case, by including the rigid-body equation of motion for its simultaneous time integration with the governing flow equations. Results are presented for a 75 deg swept sharp leading edge delta wing at a freestream Mach number of 1.2 and at alpha equal to 10 and 30 deg angle of attack. A forced harmonic analysis indicates that the rolling moment coefficient provides: (1) a positive damping at the lower angle of attack equal to 10 deg, which is verified in a free-to-roll calculation; (2) a negative damping at the higher angle of attack equal to 30 deg at the small roll amplitudes. A free-to-roll calculation for the latter case produces an initially divergent response, but as the amplitude of motion grows with time, the response transitions to a wing-rock type of limit cycle oscillation. The wing rocking motion may be actively suppressed, however, through the use of a rate-feedback control law and antisymmetrically deflected leading edge flaps. The descriptions of the conical Euler flow solver and the free-to-roll analysis are presented. Results are also presented which give insight into the flow physics associated with unsteady vortical flows about forced and free-to-roll delta wings, including the active roll suppression of this wing-rock phenomenon.

40 CFR 467.21 - Specialized definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... AND STANDARDS (CONTINUED) ALUMINUM FORMING POINT SOURCE CATEGORY Rolling With Emulsions Subcategory... emulsions subcategory shall include rolling using emulsions, roll grinding, stationary casting, homogenizing...

40 CFR 467.21 - Specialized definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... AND STANDARDS (CONTINUED) ALUMINUM FORMING POINT SOURCE CATEGORY Rolling With Emulsions Subcategory... emulsions subcategory shall include rolling using emulsions, roll grinding, stationary casting, homogenizing...

40 CFR 467.21 - Specialized definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... AND STANDARDS (CONTINUED) ALUMINUM FORMING POINT SOURCE CATEGORY Rolling With Emulsions Subcategory... emulsions subcategory shall include rolling using emulsions, roll grinding, stationary casting, homogenizing...

iROLL: does 3-D radioguided occult lesion localization improve surgical management in early-stage breast cancer?

PubMed

Bluemel, Christina; Cramer, Andreas; Grossmann, Christoph; Kajdi, Georg W; Malzahn, Uwe; Lamp, Nora; Langen, Heinz-Jakob; Schmid, Jan; Buck, Andreas K; Grimminger, Hanns-Jörg; Herrmann, Ken

2015-10-01

To prospectively evaluate the feasibility of 3-D radioguided occult lesion localization (iROLL) and to compare iROLL with wire-guided localization (WGL) in patients with early-stage breast cancer undergoing breast-conserving surgery and sentinel lymph node biopsy (SLNB). WGL (standard procedure) and iROLL in combination with SLNB were performed in 31 women (mean age 65.1 ± 11.2 years) with early-stage breast cancer and clinically negative axillae. Patient comfort in respect of both methods was assessed using a ten point scale. SLNB and iROLL were guided by freehand SPECT (fhSPECT). The results of the novel 3-D image-based method were compared with those of WGL, ultrasound-based lesion localization, and histopathology. iROLL successfully detected the malignant primary and at least one sentinel lymph node in 97% of patients. In a single patient (3%), only iROLL, and not WGL, enabled lesion localization. The variability between fhSPECT and ultrasound-based depth localization of breast lesions was low (1.2 ± 1.4 mm). Clear margins were achieved in 81% of the patients; however, precise prediction of clear histopathological surgical margins was not feasible using iROLL. Patients rated iROLL as less painful than WGL with a pain score 0.8 ± 1.2 points (p < 0.01) lower than the score for iROLL. iROLL is a well-tolerated and feasible technique for localizing early-stage breast cancer in the course of breast-conserving surgery, and is a suitable replacement for WGL. As a single image-based procedure for localization of breast lesions and sentinel nodes, iROLL may improve the entire surgical procedure. However, no advantages of the image-guided procedure were found with regard to prediction of complete tumour resection.

Toward large-area roll-to-roll printed nanophotonic sensors

NASA Astrophysics Data System (ADS)

Karioja, Pentti; Hiltunen, Jussi; Aikio, Sanna M.; Alajoki, Teemu; Tuominen, Jarkko; Hiltunen, Marianne; Siitonen, Samuli; Kontturi, Ville; Böhlen, Karl; Hauser, Rene; Charlton, Martin; Boersma, Arjen; Lieberzeit, Peter; Felder, Thorsten; Eustace, David; Haskal, Eliav

2014-05-01

Polymers have become an important material group in fabricating discrete photonic components and integrated optical devices. This is due to their good properties: high optical transmittance, versatile processability at relative low temperatures and potential for low-cost production. Recently, nanoimprinting or nanoimprint lithography (NIL) has obtained a plenty of research interest. In NIL, a mould is pressed against a substrate coated with a moldable material. After deformation of the material, the mold is separated and a replica of the mold is formed. Compared with conventional lithographic methods, imprinting is simple to carry out, requires less-complicated equipment and can provide high-resolution with high throughput. Nanoimprint lithography has shown potential to become a method for low-cost and high-throughput fabrication of nanostructures. We show the development process of nano-structured, large-area multi-parameter sensors using Photonic Crystal (PC) and Surface Enhanced Raman Scattering (SERS) methodologies for environmental and pharmaceutical applications. We address these challenges by developing roll-to-roll (R2R) UV-nanoimprint fabrication methods. Our development steps are the following: Firstly, the proof of concept structures are fabricated by the use of wafer-level processes in Si-based materials. Secondly, the master molds of successful designs are fabricated, and they are used to transfer the nanophotonic structures into polymer materials using sheet-level UV-nanoimprinting. Thirdly, the sheet-level nanoimprinting processes are transferred to roll-to-roll fabrication. In order to enhance roll-to-roll manufacturing capabilities, silicone-based polymer material development was carried out. In the different development phases, Photonic Crystal and SERS sensor structures with increasing complexities were fabricated using polymer materials in order to enhance sheet-level and roll-to-roll manufacturing processes. In addition, chemical and molecular imprint (MIP) functionalization methods were applied in the sensor demonstrators. In this paper, the process flow in fabricating large-area nanophotonic structures by the use of sheet-level and roll-to-roll UV- nanoimprinting is reported.

Leaf-rolling in maize crops: from leaf scoring to canopy-level measurements for phenotyping

PubMed Central

Madec, Simon; Irfan, Kamran; Lopez, Jeremy; Comar, Alexis; Hemmerlé, Matthieu; Dutartre, Dan; Praud, Sebastien; Tixier, Marie Helene

2018-01-01

Abstract Leaf rolling in maize crops is one of the main plant reactions to water stress that can be visually scored in the field. However, leaf-scoring techniques do not meet the high-throughput requirements needed by breeders for efficient phenotyping. Consequently, this study investigated the relationship between leaf-rolling scores and changes in canopy structure that can be determined by high-throughput remote-sensing techniques. Experiments were conducted in 2015 and 2016 on maize genotypes subjected to water stress. Leaf-rolling was scored visually over the whole day around the flowering stage. Concurrent digital hemispherical photographs were taken to evaluate the impact of leaf-rolling on canopy structure using the computed fraction of intercepted diffuse photosynthetically active radiation, FIPARdif. The results showed that leaves started to roll due to water stress around 09:00 h and leaf-rolling reached its maximum around 15:00 h (the photoperiod was about 05:00–20:00 h). In contrast, plants maintained under well-watered conditions did not show any significant rolling during the same day. A canopy-level index of rolling (CLIR) is proposed to quantify the diurnal changes in canopy structure induced by leaf-rolling. It normalizes for the differences in FIPARdif between genotypes observed in the early morning when leaves are unrolled, as well as for yearly effects linked to environmental conditions. Leaf-level rolling score was very strongly correlated with changes in canopy structure as described by the CLIR (r2=0.86, n=370). The daily time course of rolling was characterized using the amplitude of variation, and the rate and the timing of development computed at both the leaf and canopy levels. Results obtained from eight genotypes common between the two years of experiments showed that the amplitude of variation of the CLIR was the more repeatable trait (Spearman coefficient ρ=0.62) as compared to the rate (ρ=0.29) and the timing of development (ρ=0.33). The potential of these findings for the development of a high-throughput method for determining leaf-rolling based on aerial drone observations are considered. PMID:29617837

Modulation of Internal Estimates of Gravity during and after Prolonged Roll-Tilts

PubMed Central

Tarnutzer, Alexander A.; Bertolini, Giovanni; Bockisch, Christopher J.; Straumann, Dominik; Marti, Sarah

2013-01-01

Perceived direction of gravity, as assessed by the subjective visual vertical (SVV), shows roll-angle dependent errors that drift over time and a bias upon return to upright. According to Bayesian observer theory, the estimated direction of gravity is derived from the posterior probability distribution by combining sensory input and prior knowledge about earth-vertical in a statistically optimal fashion. Here we aimed to further characterize the stability of SVV during and after prolonged roll-tilts. Specifically we asked whether the post-tilt bias is related to the drift pattern while roll-tilted. Twenty-nine healthy human subjects (23-56yo) repetitively adjusted a luminous arrow to the SVV over periods of 5min while upright, roll-tilted (±45°, ±90°), and immediately after returning to upright. Significant (p<0.05) drifts (median absolute drift-amplitude: 10°/5min) were found in 71% (±45°) and 78% (±90°) of runs. At ±90° roll-tilt significant increases in absolute adjustment errors were more likely (76%), whereas significant increases (56%) and decreases (44%) were about equally frequent at ±45°. When returning to upright, an initial bias towards the previous roll-position followed by significant exponential decay (median time-constant: 71sec) was noted in 47% of all runs (all subjects pooled). No significant correlations were found between the drift pattern during and immediately after prolonged roll-tilt. We conclude that the SVV is not stable during and after prolonged roll-tilt and that the direction and magnitude of drift are individually distinct and roll-angle-dependent. Likely sensory and central adaptation and random-walk processes contribute to drift while roll-tilted. Lack of correlation between the drift and the post-tilt bias suggests that it is not the inaccuracy of the SVV estimate while tilted that determines post-tilt bias, but rather the previous head-roll orientation relative to gravity. We therefore favor central adaptation, most likely a shift in prior knowledge towards the previous roll orientation, to explain the post-tilt bias. PMID:24205099

Modulation of internal estimates of gravity during and after prolonged roll-tilts.

PubMed

Tarnutzer, Alexander A; Bertolini, Giovanni; Bockisch, Christopher J; Straumann, Dominik; Marti, Sarah

2013-01-01

Perceived direction of gravity, as assessed by the subjective visual vertical (SVV), shows roll-angle dependent errors that drift over time and a bias upon return to upright. According to Bayesian observer theory, the estimated direction of gravity is derived from the posterior probability distribution by combining sensory input and prior knowledge about earth-vertical in a statistically optimal fashion. Here we aimed to further characterize the stability of SVV during and after prolonged roll-tilts. Specifically we asked whether the post-tilt bias is related to the drift pattern while roll-tilted. Twenty-nine healthy human subjects (23-56 yo) repetitively adjusted a luminous arrow to the SVV over periods of 5 min while upright, roll-tilted (± 45°, ± 90°), and immediately after returning to upright. Significant (p<0.05) drifts (median absolute drift-amplitude: 10°/5 min) were found in 71% (± 45°) and 78% (± 90°) of runs. At ± 90° roll-tilt significant increases in absolute adjustment errors were more likely (76%), whereas significant increases (56%) and decreases (44%) were about equally frequent at ± 45°. When returning to upright, an initial bias towards the previous roll-position followed by significant exponential decay (median time-constant: 71 sec) was noted in 47% of all runs (all subjects pooled). No significant correlations were found between the drift pattern during and immediately after prolonged roll-tilt. We conclude that the SVV is not stable during and after prolonged roll-tilt and that the direction and magnitude of drift are individually distinct and roll-angle-dependent. Likely sensory and central adaptation and random-walk processes contribute to drift while roll-tilted. Lack of correlation between the drift and the post-tilt bias suggests that it is not the inaccuracy of the SVV estimate while tilted that determines post-tilt bias, but rather the previous head-roll orientation relative to gravity. We therefore favor central adaptation, most likely a shift in prior knowledge towards the previous roll orientation, to explain the post-tilt bias.

Conical Euler analysis and active roll suppression for unsteady vortical flows about rolling delta wings

NASA Technical Reports Server (NTRS)

Lee-Rausch, Elizabeth M.; Batina, John T.

1993-01-01

A conical Euler code was developed to study unsteady vortex-dominated flows about rolling, highly swept delta wings undergoing either forced motions or free-to-roll motions that include active roll suppression. The flow solver of the code involves a multistage, Runge-Kutta time-stepping scheme that uses a cell-centered, finite-volume, spatial discretization of the Euler equations on an unstructured grid of triangles. The code allows for the additional analysis of the free to-roll case by simultaneously integrating in time the rigid-body equation of motion with the governing flow equations. Results are presented for a delta wing with a 75 deg swept, sharp leading edge at a free-stream Mach number of 1.2 and at 10 deg, 20 deg, and 30 deg angle of attack alpha. At the lower angles of attack (10 and 20 deg), forced-harmonic analyses indicate that the rolling-moment coefficients provide a positive damping, which is verified by free-to-roll calculations. In contrast, at the higher angle of attack (30 deg), a forced-harmonic analysis indicates that the rolling-moment coefficient provides negative damping at the small roll amplitudes. A free-to-roll calculation for this case produces an initially divergent response, but as the amplitude of motion grows with time, the response transitions to a wing-rock type of limit cycle oscillation, which is characteristic of highly swept delta wings. This limit cycle oscillation may be actively suppressed through the use of a rate-feedback control law and antisymmetrically deflected leading-edge flaps. Descriptions of the conical Euler flow solver and the free-to roll analysis are included in this report. Results are presented that demonstrate how the systematic analysis of the forced response of the delta wing can be used to predict the stable, neutrally stable, and unstable free response of the delta wing. These results also give insight into the flow physics associated with unsteady vortical flows about delta wings undergoing forced motions and free-to-roll motions, including the active suppression of the wing-rock type phenomenon. The conical Euler methodology developed is directly extend able to three-dimensional calculations.

Laboratory and Workplace Assessments of Rivet Bucking Bar Vibration Emissions

PubMed Central

McDowell, Thomas W.; Warren, Christopher; Xu, Xueyan S.; Welcome, Daniel E.; Dong, Ren G.

2016-01-01

Sheet metal workers operating rivet bucking bars are at risk of developing hand and wrist musculoskeletal disorders associated with exposures to hand-transmitted vibrations and forceful exertions required to operate these hand tools. New bucking bar technologies have been introduced in efforts to reduce workplace vibration exposures to these workers. However, the efficacy of these new bucking bar designs has not been well documented. While there are standardized laboratory-based methodologies for assessing the vibration emissions of many types of powered hand tools, no such standard exists for rivet bucking bars. Therefore, this study included the development of a laboratory-based method for assessing bucking bar vibrations which utilizes a simulated riveting task. With this method, this study evaluated three traditional steel bucking bars, three similarly shaped tungsten alloy bars, and three bars featuring spring-dampeners. For comparison the bucking bar vibrations were also assessed during three typical riveting tasks at a large aircraft maintenance facility. The bucking bars were rank-ordered in terms of unweighted and frequency-weighted acceleration measured at the hand-tool interface. The results suggest that the developed laboratory method is a reasonable technique for ranking bucking bar vibration emissions; the lab-based riveting simulations produced similar rankings to the workplace rankings. However, the laboratory-based acceleration averages were considerably lower than the workplace measurements. These observations suggest that the laboratory test results are acceptable for comparing and screening bucking bars, but the laboratory measurements should not be directly used for assessing the risk of workplace bucking bar vibration exposures. The newer bucking bar technologies exhibited significantly reduced vibrations compared to the traditional steel bars. The results of this study, together with other information such as rivet quality, productivity, tool weight, comfort, worker acceptance, and initial cost can be used to make informed bucking bar selections. PMID:25381185

Laboratory and workplace assessments of rivet bucking bar vibration emissions.

PubMed

McDowell, Thomas W; Warren, Christopher; Xu, Xueyan S; Welcome, Daniel E; Dong, Ren G

2015-04-01

Sheet metal workers operating rivet bucking bars are at risk of developing hand and wrist musculoskeletal disorders associated with exposures to hand-transmitted vibrations and forceful exertions required to operate these hand tools. New bucking bar technologies have been introduced in efforts to reduce workplace vibration exposures to these workers. However, the efficacy of these new bucking bar designs has not been well documented. While there are standardized laboratory-based methodologies for assessing the vibration emissions of many types of powered hand tools, no such standard exists for rivet bucking bars. Therefore, this study included the development of a laboratory-based method for assessing bucking bar vibrations which utilizes a simulated riveting task. With this method, this study evaluated three traditional steel bucking bars, three similarly shaped tungsten alloy bars, and three bars featuring spring-dampeners. For comparison the bucking bar vibrations were also assessed during three typical riveting tasks at a large aircraft maintenance facility. The bucking bars were rank-ordered in terms of unweighted and frequency-weighted acceleration measured at the hand-tool interface. The results suggest that the developed laboratory method is a reasonable technique for ranking bucking bar vibration emissions; the lab-based riveting simulations produced similar rankings to the workplace rankings. However, the laboratory-based acceleration averages were considerably lower than the workplace measurements. These observations suggest that the laboratory test results are acceptable for comparing and screening bucking bars, but the laboratory measurements should not be directly used for assessing the risk of workplace bucking bar vibration exposures. The newer bucking bar technologies exhibited significantly reduced vibrations compared to the traditional steel bars. The results of this study, together with other information such as rivet quality, productivity, tool weight, comfort, worker acceptance, and initial cost can be used to make informed bucking bar selections. Published by Oxford University Press on behalf of the British Occupational Hygiene Society 2014.

The company they keep: drinking group attitudes and male bar aggression.

PubMed

Dumas, Tara M; Graham, Kathryn; Wells, Samantha

2015-05-01

The purpose of this study was to assess (a) similarities in self-reported bar-aggression-related attitudes and behaviors among members of young male groups recruited on their way to bars and (b) group-level variables associated with individual members' self-reported likelihood of perpetrating physical bar aggression in the past year, controlling for individual attitudes. Young, male, natural drinking groups recruited on their way to a bar district Thursday, Friday, and Saturday nights (n = 167, 53 groups) completed an online survey that measured whether they had perpetrated physical aggression at a bar in the past year and constructs associated with bar aggression, including attitudes toward male bar aggression and frequency of heavy episodic drinking in the past year. Intraclass correlations and chi-square tests demonstrated significant within-group similarity on bar-aggression-related attitudes and behaviors (ps < .01). Hierarchical linear modeling revealed that group attitudes toward bar aggression were significantly associated with individuals' likelihood of perpetrating physical bar aggression, controlling for individual attitudes (p < .01); however, the link between group heavy episodic drinking and self-reported bar aggression was nonsignificant in the full model. This study suggests that the most important group influence on young men's bar aggression is the attitudes of other group members. These attitudes were associated with group members' likelihood of engaging in bar aggression over and above individuals' own attitudes. A better understanding of how group attitudes and behavior affect the behavior of individual group members is needed to inform aggression-prevention programming.

Influence of the weighing bar size to determine optimal time of biodiesel-glycerol separation by using the buoyancy weighing-bar method

NASA Astrophysics Data System (ADS)

Tambun, R.; Sibagariang, Y.; Manurung, J.

2018-02-01

The buoyancy weighing-bar method is a novel method in the particle size distribution measurement. This method can measure particle size distributions of the settling particles and floating particles. In this study, the buoyancy weighing-bar method is applied to determine optimal time of biodiesel-glycerol separation. The buoyancy weighing-bar method can be applied to determine the separation time because biodiesel and glycerol have the different densities. The influences of diameter of weighing-bar by using the buoyancy weighing-bar method would be experimentally investigated. The diameters of weighing-bar in this experiment are 8 mm, 10 mm, 15 mm and 20 mm, while the graduated cylinder (diameter : 65 mm) is used as vessel. The samples used in this experiment are the mixture of 95 % of biodiesel and 5 % of glycerol. The data obtained by the buoyancy weighing-bar method are analized by using the gas chromatography to determine the purity of biodiesel. Based on the data obtained, the buoyancy weighing-bar method can be used to detect the separation time of biodiesel-glycerol by using the weighing-bar diameter of 8 mm, 10 mm, 15 mm and 20 mm, but the most accuracy in determination the biodiesel-glycerol separation time is obtained by using the weighing-bar diameter of 20 mm. The biodiesel purity of 97.97 % could be detected at 64 minutes by using the buoyancy weighing-bar method when the weighing-bar diameter of 20 mm is used.

Influence of the weighing bar position in vessel on measurement of cement’s particle size distribution by using the buoyancy weighing-bar method

NASA Astrophysics Data System (ADS)

Tambun, R.; Sihombing, R. O.; Simanjuntak, A.; Hanum, F.

2018-02-01

The buoyancy weighing-bar method is a new simple and cost-effective method to determine the particle size distribution both settling and floating particle. In this method, the density change in a suspension due to particle migration is measured by weighing buoyancy against a weighing-bar hung in the suspension, and then the particle size distribution is calculated using the length of the bar and the time-course change in the mass of the bar. The apparatus of this method consists of a weighing-bar and an analytical balance with a hook for under-floor weighing. The weighing bar is used to detect the density change in suspension. In this study we investigate the influences of position of weighing bar in vessel on settling particle size distribution measurements of cement by using the buoyancy weighing-bar method. The vessel used in this experiment is graduated cylinder with the diameter of 65 mm and the position of weighing bar is in center and off center of vessel. The diameter of weighing bar in this experiment is 10 mm, and the kerosene is used as a dispersion liquids. The results obtained show that the positions of weighing bar in vessel have no significant effect on determination the cement’s particle size distribution by using buoyancy weighing-bar method, and the results obtained are comparable to those measured by using settling balance method.

Glass Fiber Reinforced Polymer Dowel Bar Evaluation

DOT National Transportation Integrated Search

2012-09-01

Glass Fiber Reinforced Polymer (GFRP) dowel bars were installed on one new construction project and two dowel bar : retrofit projects to evaluate the performance of this type of dowel bar in comparison to steel dowel bars installed on the same : cont...

Comparison of S. cerevisiae F-BAR domain structures reveals a conserved inositol phosphate binding site

PubMed Central

Moravcevic, Katarina; Alvarado, Diego; Schmitz, Karl R.; Kenniston, Jon A.; Mendrola, Jeannine M.; Ferguson, Kathryn M.; Lemmon, Mark A.

2015-01-01

SUMMARY F-BAR domains control membrane interactions in endocytosis, cytokinesis, and cell signaling. Although generally thought to bind curved membranes containing negatively charged phospholipids, numerous functional studies argue that differences in lipid-binding selectivities of F-BAR domains are functionally important. Here, we compare membrane-binding properties of the S. cerevisiae F-BAR domains in vitro and in vivo. Whereas some F-BAR domains (such as Bzz1p and Hof1p F-BARs) bind equally well to all phospholipids, the F-BAR domain from the RhoGAP Rgd1p preferentially binds phosphoinositides. We determined X-ray crystal structures of F-BAR domains from Hof1p and Rgd1p, the latter bound to an inositol phosphate. The structures explain phospholipid-binding selectivity differences, and reveal an F-BAR phosphoinositide binding site that is fully conserved in a mammalian RhoGAP called Gmip, and is partly retained in certain other F-BAR domains. Our findings reveal previously unappreciated determinants of F-BAR domain lipid-binding specificity, and provide a basis for its prediction from sequence. PMID:25620000

Comparing Monofractal and Multifractal Analysis of Corrosion Damage Evolution in Reinforcing Bars

PubMed Central

Xu, Yidong; Qian, Chunxiang; Pan, Lei; Wang, Bingbing; Lou, Chi

2012-01-01

Based on fractal theory and damage mechanics, the aim of this paper is to describe the monofractal and multifractal characteristics of corrosion morphology and develop a new approach to characterize the nonuniform corrosion degree of reinforcing bars. The relationship between fractal parameters and tensile strength of reinforcing bars are discussed. The results showed that corrosion mass loss ratio of a bar cannot accurately reflect the damage degree of the bar. The corrosion morphology of reinforcing bars exhibits both monofractal and multifractal features. The fractal dimension and the tensile strength of corroded steel bars exhibit a power function relationship, while the width of multifractal spectrum and tensile strength of corroded steel bars exhibit a linear relationship. By comparison, using width of multifractal spectrum as multifractal damage variable not only reflects the distribution of corrosion damage in reinforcing bars, but also reveals the influence of nonuniform corrosion on the mechanical properties of reinforcing bars. The present research provides a new approach for the establishment of corrosion damage constitutive models of reinforcing bars. PMID:22238682

Tree-level contributions to the rare decays B+→π+νν¯, B+→K+νν¯, and B+→K*νν¯ in the Standard Model

NASA Astrophysics Data System (ADS)

Kamenik, Jernej F.; Smith, Christopher

2009-10-01

The tree-level contributions to the rare decays B+ →π+ ννbar, B+ →K+ ννbar, and B+ →K*+ ννbar are analyzed and compared to those occurring in K+ →π+ ννbar, D+ →π+ ννbar, and Ds+ →π+ ννbar. It is shown that these purely long-distance contributions, arising from the exchange of a charged lepton, can be significant in B+ decays for an intermediate τ, potentially blurring the distinction between the modes used to extract B+ →τ+ντ and those used to probe the genuine short-distance b → dννbar and b → sννbar FCNC transitions. Numerically, the tree-level contributions are found to account for 98%, 12% and 14% of the total B+ →π+ ννbar, B+ →K+ ννbar, and B+ →K*+ ννbar rates, respectively.

Dynamic tensile characterization of a 4330 steel with kolsky bar techniques.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, Bo; Antoun, Bonnie R.; Connelly, Kevin

2010-08-01

There has been increasing demand to understand the stress-strain response as well as damage and failure mechanisms of materials under impact loading condition. Dynamic tensile characterization has been an efficient approach to acquire satisfactory information of mechanical properties including damage and failure of the materials under investigation. However, in order to obtain valid experimental data, reliable tensile experimental techniques at high strain rates are required. This includes not only precise experimental apparatus but also reliable experimental procedures and comprehensive data interpretation. Kolsky bar, originally developed by Kolsky in 1949 [1] for high-rate compressive characterization of materials, has been extended formore » dynamic tensile testing since 1960 [2]. In comparison to Kolsky compression bar, the experimental design of Kolsky tension bar has been much more diversified, particularly in producing high speed tensile pulses in the bars. Moreover, instead of directly sandwiching the cylindrical specimen between the bars in Kolsky bar compression bar experiments, the specimen must be firmly attached to the bar ends in Kolsky tensile bar experiments. A common method is to thread a dumbbell specimen into the ends of the incident and transmission bars. The relatively complicated striking and specimen gripping systems in Kolsky tension bar techniques often lead to disturbance in stress wave propagation in the bars, requiring appropriate interpretation of experimental data. In this study, we employed a modified Kolsky tension bar, newly developed at Sandia National Laboratories, Livermore, CA, to explore the dynamic tensile response of a 4330-V steel. The design of the new Kolsky tension bar has been presented at 2010 SEM Annual Conference [3]. Figures 1 and 2 show the actual photograph and schematic of the Kolsky tension bar, respectively. As shown in Fig. 2, the gun barrel is directly connected to the incident bar with a coupler. The cylindrical striker set inside the gun barrel is launched to impact on the end cap that is threaded into the open end of the gun barrel, producing a tension on the gun barrel and the incident bar.« less

Dynamic tensile characterization of a 4330-V steel with kolsky bar techniques.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, Bo; Antoun, Bonnie R.; Connelly, Kevin

2010-09-01

There has been increasing demand to understand the stress-strain response as well as damage and failure mechanisms of materials under impact loading condition. Dynamic tensile characterization has been an efficient approach to acquire satisfactory information of mechanical properties including damage and failure of the materials under investigation. However, in order to obtain valid experimental data, reliable tensile experimental techniques at high strain rates are required. This includes not only precise experimental apparatus but also reliable experimental procedures and comprehensive data interpretation. Kolsky bar, originally developed by Kolsky in 1949 [1] for high-rate compressive characterization of materials, has been extended formore » dynamic tensile testing since 1960 [2]. In comparison to Kolsky compression bar, the experimental design of Kolsky tension bar has been much more diversified, particularly in producing high speed tensile pulses in the bars. Moreover, instead of directly sandwiching the cylindrical specimen between the bars in Kolsky bar compression bar experiments, the specimen must be firmly attached to the bar ends in Kolsky tensile bar experiments. A common method is to thread a dumbbell specimen into the ends of the incident and transmission bars. The relatively complicated striking and specimen gripping systems in Kolsky tension bar techniques often lead to disturbance in stress wave propagation in the bars, requiring appropriate interpretation of experimental data. In this study, we employed a modified Kolsky tension bar, newly developed at Sandia National Laboratories, Livermore, CA, to explore the dynamic tensile response of a 4330-V steel. The design of the new Kolsky tension bar has been presented at 2010 SEM Annual Conference [3]. Figures 1 and 2 show the actual photograph and schematic of the Kolsky tension bar, respectively. As shown in Fig. 2, the gun barrel is directly connected to the incident bar with a coupler. The cylindrical striker set inside the gun barrel is launched to impact on the end cap that is threaded into the open end of the gun barrel, producing a tension on the gun barrel and the incident bar.« less

76 FR 30529 - Airworthiness Directives; Rolls-Royce plc (RR) RB211-535 Series Turbofan Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-26

... Airworthiness Directives; Rolls-Royce plc (RR) RB211-535 Series Turbofan Engines AGENCY: Federal Aviation... To Change Related Information Paragraph One commenter, Rolls-Royce plc asked us to use a different... Airlines, and Rolls-Royce plc asked us to change the definition of a shop visit to the definition in the...

77 FR 10355 - Airworthiness Directives; Rolls-Royce plc (RR) RB211-Trent 800 Series Turbofan Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-22

... Airworthiness Directives; Rolls-Royce plc (RR) RB211-Trent 800 Series Turbofan Engines AGENCY: Federal Aviation... effective March 28, 2012. ADDRESSES: For service information identified in this AD, contact Rolls-Royce plc... Rolls-Royce plc: Amendment 39-16956; Docket No. FAA-2010- 0755; Directorate Identifier 2010-NE-12-AD. (a...

Raising the Reliability of Forming Rolls by Alloying Their Core with Copper

NASA Astrophysics Data System (ADS)

Zhizhkina, N. A.

2016-11-01

The mechanical properties and the structure of forming rolls from cast irons of different compositions are studied. A novel iron including a copper additive that lowers its chilling and raises the homogeneity of the structure is suggested for the roll cores. The use of such iron should raise the reliability of the rolls in operation.

77 FR 14341 - Certain Hot-Rolled Carbon Steel Flat Products From Taiwan: Notice of Rescission of Antidumping...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-09

... DEPARTMENT OF COMMERCE International Trade Administration [A-583-835] Certain Hot-Rolled Carbon... order on certain hot-rolled carbon steel flat products from Taiwan. The period of review is November 1... antidumping duty order on certain hot- rolled carbon steel flat products from Taiwan covering the period...

78 FR 16500 - Rolling Bay, LLC and Indus; Transfer of Data

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-15

... contract to perform work for OPP, and access to this information will enable Rolling Bay, LLC and its subcontractor, Indus, to fulfill the obligations of the contract. DATES: Rolling Bay, LLC and its subcontractor... Under Contract No. GS-35F-0072Y, Rolling Bay, LLC and its subcontractor, Indus, will: Capture data that...

78 FR 17080 - Airworthiness Directives; Rolls-Royce Deutschland Ltd & Co KG Turbofan Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-20

... Airworthiness Directives; Rolls-Royce Deutschland Ltd & Co KG Turbofan Engines AGENCY: Federal Aviation... certain Rolls-Royce Deutschland Ltd & Co KG (RRD) BR700-710 series turbofan engines. This AD requires... applies to Rolls-Royce Deutschland Ltd & Co KG (RRD) BR700-710A1-10 and BR700-710A2-20 turbofan engines...

76 FR 41045 - Special Conditions; Gulfstream Aerospace LP (GALP) Model G250 Airplane, Design Roll-Maneuver...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-13

... with electronic flight controls as they relate to design roll-maneuver requirements. The applicable... load condition at design maneuvering speed V A , in which the cockpit roll control is returned to... neutral position. 3. At design cruising speed V C , the cockpit roll control must be moved suddenly and...

77 FR 70384 - Special Conditions: Embraer S.A., Model EMB-550 Airplane; Design Roll Maneuver for Electronic...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-26

... design roll maneuver for electronic flight controls, specifically an electronic flight control system... load condition at design maneuvering speed (V A ), in which the cockpit roll control is returned to...-550 airplanes. 1. Design Roll Maneuver for Electronic Flight Controls. In lieu of compliance to 14 CFR...

75 FR 59689 - Certain Hot-Rolled Carbon Steel Flat Products From India: Notice of Court Decision Not in Harmony...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-28

... DEPARTMENT OF COMMERCE International Trade Administration [C-533-821] Certain Hot-Rolled Carbon... certain hot-rolled carbon steel flat products (HRCS) from India covering the period of review (POR) of January 1, 2006, through December 31, 2006. See Certain Hot-Rolled Carbon Steel Flat Products from India...

Airborne Optical Systems Test Bed (AOSTB)

DTIC Science & Technology

2016-07-01

resident laser radar platform with roll -on/ roll -off sensor capability. The new platform provides The Laboratory with an added capability of leveraging...29 Figure 11 – Finite Element Analysis of Loads on Isolators (9G Forward...This project created a resident sensor suite with roll -on/ roll -off capability, coupled to a resident platform (Twin Otter Aircraft). This facility

78 FR 16252 - Certain Hot-Rolled Carbon Steel Flat Products From India, Indonesia, and Thailand: Final Results...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-14

...] Certain Hot-Rolled Carbon Steel Flat Products From India, Indonesia, and Thailand: Final Results of... second sunset reviews of the countervailing duty (``CVD'') orders on certain hot-rolled carbon steel flat...). Scope of the Orders The merchandise subject to these orders is hot-rolled steel of a rectangular shape...

Investigation at Low Speeds of the Effect of Aspect Ratio and Sweep on Rolling Stability Derivatives of Untapered Wings

NASA Technical Reports Server (NTRS)

Goodman, Alex; Fisher, Lewis R

1950-01-01

A low-scale wind-tunnel investigation was conducted in rolling flow to determine the effects of aspect ratio and sweep (when varied independently) on the rolling stability derivatives for a series of untapered wings. The rolling-flow equipment of the Langley stability tunnel was used for the tests. The data of the investigation have been used to develop a method of accounting for the effects of the drag on the yawing moment due to rolling throughout the lift range.

Fluidic emergency roll control system. [for emergency aircraft control following failure of primary roll control system

NASA Technical Reports Server (NTRS)

Haefner, K. B.; Honda, T. S.

1973-01-01

A fluidic emergency roll control system for aircraft stabilization in the event of primary flight control failure was evaluated. The fluidic roll control units were designed to provide roll torque proportional to an electrical command as operated by two diametrically opposed thrust nozzles located in the wing tips. The control package consists of a solid propellant gas generator, two diametrically opposed vortex valve modulated thrust nozzles, and an electromagnetic torque motor. The procedures for the design, development, and performance testing of the system are described.

Process optimization of rolling for zincked sheet technology using response surface methodology and genetic algorithm

NASA Astrophysics Data System (ADS)

Ji, Liang-Bo; Chen, Fang

2017-07-01

Numerical simulation and intelligent optimization technology were adopted for rolling and extrusion of zincked sheet. By response surface methodology (RSM), genetic algorithm (GA) and data processing technology, an efficient optimization of process parameters for rolling of zincked sheet was investigated. The influence trend of roller gap, rolling speed and friction factor effects on reduction rate and plate shortening rate were analyzed firstly. Then a predictive response surface model for comprehensive quality index of part was created using RSM. Simulated and predicted values were compared. Through genetic algorithm method, the optimal process parameters for the forming of rolling were solved. They were verified and the optimum process parameters of rolling were obtained. It is feasible and effective.

Development of a Rolling Process Design Tool for Use in Improving Hot Roll Slab Recovery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Couch, R; Becker, R; Rhee, M

2004-09-24

Lawrence Livermore National Laboratory participated in a U. S. Department of Energy/Office of Industrial Technology sponsored research project 'Development of a Rolling Process Design Tool for Use in Improving Hot Roll Slab Recovery', as a Cooperative Agreement TC-02028 with the Alcoa Technical Center (ATC). The objective of the joint project with Alcoa is to develop a numerical modeling capability to optimize the hot rolling process used to produce aluminum plate. Product lost in the rolling process and subsequent recycling, wastes resources consumed in the energy-intensive steps of remelting and reprocessing the ingot. The modeling capability developed by project partners willmore » be used to produce plate more efficiently and with reduced product loss.« less

New perspectives on constant-roll inflation

NASA Astrophysics Data System (ADS)

Cicciarella, Francesco; Mabillard, Joel; Pieroni, Mauro

2018-01-01

We study constant-roll inflation using the β-function formalism. We show that the constant rate of the inflaton roll is translated into a first order differential equation for the β-function which can be solved easily. The solutions to this equation correspond to the usual constant-roll models. We then construct, by perturbing these exact solutions, more general classes of models that satisfy the constant-roll equation asymptotically. In the case of an asymptotic power law solution, these corrections naturally provide an end to the inflationary phase. Interestingly, while from a theoretical point of view (in particular in terms of the holographic interpretation) these models are intrinsically different from standard slow-roll inflation, they may have phenomenological predictions in good agreement with present cosmological data.

Influence of Accumulative Roll Bonding on the Texture and Tensile Properties of an AZ31 Magnesium Alloy Sheets

PubMed Central

Džugan, Ján; Németh, Gergely; Lukáč, Pavel; Bohlen, Jan

2018-01-01

Deformation behaviour of rolled AZ31 sheets that were subjected to the accumulative roll bonding was investigated. Substantially refined microstructure of samples was achieved after the first and second pass through the rolling mill. Sheets texture was investigated using an X-ray diffractometer. Samples for tensile tests were cut either parallel or perpendicular to the rolling direction. Tensile tests were performed at temperatures ranging from room temperature up to 300 °C. Tensile plastic anisotropy, different from the anisotropy observed in AZ31 sheets by other authors, was observed. This anisotropy decreases with an increasing number of rolling passes and increasing deformation temperature. Grain refinement and texture are the crucial factors influencing the deformation behaviour. PMID:29303975

Unintended Consequences of Smoke-Free Bar Policies for Low-SES Women in Three California Counties

PubMed Central

Moore, Roland S.; Annechino, Rachelle M.; Lee, Juliet P.

2009-01-01

Background To amplify earlier studies of unintended consequences of public policies, this article illustrates both negative and positive unanticipated consequences of smoke-free workplace policies in California bars for women of low SES. Methods The article relies on thematic analysis in 2008 of qualitative data gathered between 2001 and 2007 from three mixed-method studies of tobacco use in and around bars where indoor smoking is prohibited. Results Unanticipated consequences primarily occurred when bars did comply with the law and smokers went outside the bar to smoke, particularly when smokers stood on the street outside the bar. Key negative consequences for women who smoked outside of bars included threats to their physical safety and their public image. For women living near bars, increased smoking on the street may have increased their exposure to secondhand smoke and disruptive noise. For some women, however, unanticipated negative consequences were identified with noncompliant bars. Smokers were conjectured to congregate in the smaller number of bars where smoking was still allowed, resulting in increased exposure to secondhand smoke for low-SES women working in these bars. A common positive unintended consequence of the tobacco control ordinance was increased social circulation and solidarity, as smokers gathered outside bars to smoke. Conclusions Smoke-free workplace laws in bars can have both negative and positive consequences for workers and smokers, and low-income women in particular. PMID:19591753

First observation of γγ-> p$$\\bar{p}$$K +K - and search for exotic baryons in pK systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shen, C. P.; Yuan, C. Z.; Adachi, I.

The process γγ→pmore » $$\\bar{p}$$K +K - and its intermediate processes are measured for the first time using a 980 fb -1 data sample collected with the Belle detector at the KEKB asymmetric-energy e +e - collider. The production of p$$\\bar{p}$$K +K - and a Λ(1520) 0 ($$\\bar{Λ}$$(1520) 0) signal in the pK - ($$\\bar{p}$$K +) invariant mass spectrum are clearly observed. However, no evidence for an exotic baryon near 1540 MeV/c 2, denoted as Θ(1540) 0 ($$\\bar{Θ}$$(1540) 0) or Θ(1540) ++ (Θ(1540) --), is seen in the pK - ($$\\bar{p}$$K+) or pK+ ($$\\bar{p}$$K -) invariant mass spectra. Cross sections for γγ→p$$\\bar{p}$$K +K -, Λ(1520) 0$$\\bar{p}$$K ++c.c. and the products σ(γγ→Θ(1540)0$$\\bar{p}$$K ++c.c.)B(Θ(1540) 0→pK -) and σ(γγ→Θ(1540) ++$$\\bar{p}$$K -+c.c.)B(Θ(1540) ++→pK +) are measured. We also determine upper limits on the products of the χ c0 and χ c2 two-photon decay widths and their branching fractions to p$$\\bar{p}$$K +K - at the 90% credibility level.« less

Unintended consequences of smoke-free bar policies for low-SES women in three California counties.

PubMed

Moore, Roland S; Annechino, Rachelle M; Lee, Juliet P

2009-08-01

To amplify earlier studies of unintended consequences of public policies, this article illustrates both negative and positive unanticipated consequences of smoke-free workplace policies in California bars for women of low SES. The article relies on thematic analysis in 2008 of qualitative data gathered between 2001 and 2007 from three mixed-method studies of tobacco use in and around bars where indoor smoking is prohibited. Unanticipated consequences primarily occurred when bars did comply with the law and smokers went outside the bar to smoke, particularly when smokers stood on the street outside the bar. Key negative consequences for women who smoked outside of bars included threats to their physical safety and their public image. For women living near bars, increased smoking on the street may have increased their exposure to secondhand smoke and disruptive noise. For some women, however, unanticipated negative consequences were identified with noncompliant bars. Smokers were conjectured to congregate in the smaller number of bars where smoking was still allowed, resulting in increased exposure to secondhand smoke for low-SES women working in these bars. A common positive unintended consequence of the tobacco control ordinance was increased social circulation and solidarity, as smokers gathered outside bars to smoke. Smoke-free workplace laws in bars can have both negative and positive consequences for workers and smokers, and low-income women in particular.

What makes the family of barred disc galaxies so rich: damping stellar bars in spinning haloes

NASA Astrophysics Data System (ADS)

Collier, Angela; Shlosman, Isaac; Heller, Clayton

2018-05-01

We model and analyse the secular evolution of stellar bars in spinning dark matter (DM) haloes with the cosmological spin λ ˜ 0-0.09. Using high-resolution stellar and DM numerical simulations, we focus on angular momentum exchange between stellar discs and DM haloes of various axisymmetric shapes - spherical, oblate, and prolate. We find that stellar bars experience a diverse evolution that is guided by the ability of parent haloes to absorb angular momentum, J, lost by the disc through the action of gravitational torques, resonant and non-resonant. We confirm that dynamical bar instability is accelerated via resonant J-transfer to the halo. Our main findings relate to the long-term secular evolution of disc-halo systems: with an increasing λ, bars experience less growth and basically dissolve after they pass through vertical buckling instability. Specifically, with increasing λ, (1) the vertical buckling instability in stellar bars colludes with inability of the inner halo to absorb J - this emerges as the main factor weakening or destroying bars in spinning haloes; (2) bars lose progressively less J, and their pattern speeds level off; (3) bars are smaller, and for λ ≳ 0.06 cease their growth completely following buckling; (4) bars in λ > 0.03 haloes have ratio of corotation-to-bar radii, RCR/Rb > 2, and represent so-called slow bars without offset dust lanes. We provide a quantitative analysis of J-transfer in disc-halo systems, and explain the reasons for absence of growth in fast spinning haloes and its observational corollaries. We conclude that stellar bar evolution is substantially more complex than anticipated, and bars are not as resilient as has been considered so far.

Practical guide to bar coding for patient medication safety.

PubMed

Neuenschwander, Mark; Cohen, Michael R; Vaida, Allen J; Patchett, Jeffrey A; Kelly, Jamie; Trohimovich, Barbara

2003-04-15

Bar coding for the medication administration step of the drug-use process is discussed. FDA will propose a rule in 2003 that would require bar-code labels on all human drugs and biologicals. Even with an FDA mandate, manufacturer procrastination and possible shifts in product availability are likely to slow progress. Such delays should not preclude health systems from adopting bar-code-enabled point-of-care (BPOC) systems to achieve gains in patient safety. Bar-code technology is a replacement for traditional keyboard data entry. The elements of bar coding are content, which determines the meaning; data format, which refers to the embedded data and symbology, which describes the "font" in which the machine-readable code is written. For a BPOC system to deliver an acceptable level of patient protection, the hospital must first establish reliable processes for a patient identification band, caregiver badge, and medication bar coding. Medications can have either drug-specific or patient-specific bar codes. Both varieties result in the desired code that supports patient's five rights of drug administration. When medications are not available from the manufacturer in immediate-container bar-coded packaging, other means of applying the bar code must be devised, including the use of repackaging equipment, overwrapping, manual bar coding, and outsourcing. Virtually all medications should be bar coded, the bar code on the label should be easily readable, and appropriate policies, procedures, and checks should be in place. Bar coding has the potential to be not only cost-effective but to produce a return on investment. By bar coding patient identification tags, caregiver badges, and immediate-container medications, health systems can substantially increase patient safety during medication administration.

Galaxy Zoo: secular evolution of barred galaxies from structural decomposition of multiband images

NASA Astrophysics Data System (ADS)

Kruk, Sandor J.; Lintott, Chris J.; Bamford, Steven P.; Masters, Karen L.; Simmons, Brooke D.; Häußler, Boris; Cardamone, Carolin N.; Hart, Ross E.; Kelvin, Lee; Schawinski, Kevin; Smethurst, Rebecca J.; Vika, Marina

2018-02-01

We present the results of two-component (disc+bar) and three-component (disc+bar+bulge) multiwavelength 2D photometric decompositions of barred galaxies in five Sloan Digital Sky Survey (SDSS) bands (ugriz). This sample of ∼3500 nearby (z < 0.06) galaxies with strong bars selected from the Galaxy Zoo citizen science project is the largest sample of barred galaxies to be studied using photometric decompositions that include a bar component. With detailed structural analysis, we obtain physical quantities such as the bar- and bulge-to-total luminosity ratios, effective radii, Sérsic indices and colours of the individual components. We observe a clear difference in the colours of the components, the discs being bluer than the bars and bulges. An overwhelming fraction of bulge components have Sérsic indices consistent with being pseudo-bulges. By comparing the barred galaxies with a mass-matched and volume-limited sample of unbarred galaxies, we examine the connection between the presence of a large-scale galactic bar and the properties of discs and bulges. We find that the discs of unbarred galaxies are significantly bluer compared to the discs of barred galaxies, while there is no significant difference in the colours of the bulges. We find possible evidence of secular evolution via bars that leads to the build-up of pseudo-bulges and to the quenching of star formation in the discs. We identify a subsample of unbarred galaxies with an inner lens/oval and find that their properties are similar to barred galaxies, consistent with an evolutionary scenario in which bars dissolve into lenses. This scenario deserves further investigation through both theoretical and observational work.

Experimental Study on Basic Mechanical Properties of BFRP Bars

NASA Astrophysics Data System (ADS)

Fan, Xiaochun; Xu, Ting; Zhou, Zhengrong; Zhou, Xun

2017-10-01

Basalt Fiber Reinforced Polymer (BFRP) bars have the advantages of corrosion resistance, high strength, light weight, good dielectric properties, and they are new type of green reinforced alternative material. In order to determine the mechanical properties of BFRP bars, the tensile strength of basalt fiber bars was necessary to be studied. The diameters of the basalt fiber bars were compared by means of uniaxial tensile test in this article. Then the stress-strain curve can be drawn out. The results show that the stress - strain curve of BFRP bars present straight line relation, and there is no sign before failure; there is no yield platform on the stress-strain curve of BFRP bars, which are typical brittle material;the tensile strength of BFRP bars is about 3 times higher than that of ordinary steel bars. and the elastic modulus is about 1/5 of that of ordinary steel; the ultimate tensile strength of BFRP bars varies little with the increase of diameter, but there exist some differences in modulus values.

Relationships between drinking onset, alcohol use intensity, and nighttime risk behaviors in a college bar district.

PubMed

Thombs, Dennis L; O'Mara, Ryan; Tobler, Amy L; Wagenaar, Alexander C; Clapp, John D

2009-01-01

To identify antecedents of risk behavior events in college bar patrons. In this nighttime field study, self-report data and alcohol intoxication readings were collected from patrons immediately upon exiting bars (n = 618). Multilevel structural equation modeling revealed positive associations between age of drinking onset and both alcohol use intensity in the past year and recent bar-going frequency. In turn, alcohol use intensity in the past year was positively associated with bar-going frequency and intoxication at bar exit. An association between drinking onset and bar-going frequency was mediated by alcohol use intensity in the past year. Discernable paths from age of drinking onset to monthly bar-going frequency and intoxication level after leaving a bar can be identified. The results highlight the critical role of drinking onset in development of college student alcohol abuse. Research is needed to determine whether college bars are environmental pathogens mediating between genetic risk factors and patron risk behavior.

Implant-retained mandibular bar-supported overlay dentures: a finite element stress analysis of four different bar heights.

PubMed

Rismanchian, Mansoor; Dakhilalian, Mansour; Bajoghli, Farshad; Ghasemi, Ehsan; Sadr-Eshkevari, Pooyan

2012-04-01

Proper stress distribution on dental implants is necessary in bar-retained implant overlay dentures. We aimed to comparatively assess this stress distribution according to different bar heights using finite element models. A three-dimensional (3D) computer model of mandible with 2 implants (ITI, 4.1 mm diameter and 12 mm length) in canine areas and an overlying implant-supported bar-retained overlay denture were simulated with 0-, 1-, 2-, and 3-mm bar heights using ABAQUS software. A vertical force was applied to the left first molar and gradually increased from 0 to 50 N. The resultant stress distribution was evaluated. Bars of 1 and 2 mm in height transferred the least stress to the implants (3.882 and 3.896 MPa, respectively). The 0-mm height of the bar connection transferred the highest stress value (4.277 MPa). The amount of stress transferred by 3-mm heights of the bar connection was greater than that of 1- and 2-mm bar connections and smaller than that of 0-mm bar connection (4.165 kgN). This 3D finite element analysis study suggested that the use of Dolder bar attachment with 1- and 2-mm heights could be associated with appropriate stress distribution for implant-retained overlay dentures.

Why Buckling Stellar Bars Weaken in Disk Galaxies

NASA Astrophysics Data System (ADS)

Martinez-Valpuesta, Inma; Shlosman, Isaac

2004-09-01

Young stellar bars in disk galaxies experience a vertical buckling instability that terminates their growth and thickens them, resulting in a characteristic peanut/boxy shape when viewed edge-on. Using N-body simulations of galactic disks embedded in live halos, we have analyzed the bar structure throughout this instability and found that the outer (approximately) third of the bar dissolves completely while the inner part (within the vertical inner Lindblad resonance) becomes less oval. The bar acquires the frequently observed peanut/boxy-shaped isophotes. We also find that the bar buckling is responsible for a mass injection above the plane, which is subsequently trapped by specific three-dimensional families of periodic orbits of particular shapes explaining the observed isophotes, in line with previous work. Using a three-dimensional orbit analysis and surfaces of sections, we infer that the outer part of the bar is dissolved by a rapidly widening stochastic region around its corotation radius-a process related to the bar growth. This leads to a dramatic decrease in the bar size, decrease in the overall bar strength, and a mild increase in its pattern speed but is not expected to lead to a complete bar dissolution. The buckling instability appears primarily responsible for shortening the secular diffusion timescale to a dynamical one when building the boxy isophotes. The sufficiently long timescale of the described evolution, ~1 Gyr, can affect the observed bar fraction in the local universe and at higher redshifts, both through reduced bar strength and the absence of dust offset lanes in the bar.

Effects of the Bar Strength of Gaseous Features in Barred Galaxies

NASA Astrophysics Data System (ADS)

Kim, Woong-Tae; Seo, W.; Kim, Y.

2013-01-01

Barred galaxies commonly possess gaseous structures such as a pair of dust lanes, a nuclear ring, and nuclear spirals at their centers. We use hydrodynamic simulations to study the physical properties of the gaseous structures in barred galaxies and their relationships with the bar strength. We vary the bar mass fbar relative to the spheroidal component as well as its aspect ratio. We derive expressions for the bar strength Qb and the radius where the maximum bar torque occurs. When applied to observations, these expressions suggest that bars in real galaxies are most likely to have fbar = 0.25-0.5. Dust lanes approximately follow one of x1-orbits and tend to be more straight under a stronger and more elongated bar. A nuclear ring of a conventional x2 type forms only when the bar is not so massive or elongated. The radius of an x2-type ring is generally smaller than the inner Lindblad resonance, decreases systematically with increasing Qb, evidencing that the ring position is not determined by the resonance but by the bar strength. Nuclear spirals exist only when the ring is of the x2-type and sufficiently large in size. Unlike the other features, nuclear spirals are transient in that they start out as being tightly-wound and weak, and then due to the nonlinear effect unwind and become stronger until turning into shocks, with an unwinding rate higher for larger Qb. These results suggest that the bar strength is the primary factor that determine the properties of gaseous structures in barred galaxies.

How High Do Sandbars Grow?

NASA Astrophysics Data System (ADS)

Alexander, J. S.; McElroy, B. J.

2015-12-01

Bar forms in wide sandy rivers store sediment, control channel hydraulics, and are fundamental units of riverine ecosystems. Bar form height is often used as a measure of channel depth in ancient fluvial deposits and is also a crucially important measure of habitat quality in modern rivers. In the Great Plains of North America, priority bird species use emergent bars to nest, and sandbar heights are a direct predictor of flood hazard for bird nests. Our current understanding of controls on bar height are limited to few datasets and ad hoc observations from specific settings. We here examine a new dataset of bar heights and explore models of bar growth. We present bar a height dataset from the Platte and Niobrara Rivers in Nebraska, and an unchannelized reach of the Missouri River along the Nebraska-South Dakota border. Bar height data are normalized by flow frequency, and we examine parsimonious statistical models between expected controls (depth, stage, discharge, flow duration, work etc.) and maximum bar heights. From this we generate empirical-statistical models of maximum bar height for wide, sand-bedded rivers in the Great Plains of the United States and rivers of similar morphology elsewhere. Migration of bar forms is driven by downstream slip-face additions of sediment sourced from their stoss sides, but bars also sequester sediment and grow vertically and longitudinally. We explore our empirical data with a geometric-kinematic model of bar growth driven by sediment transport from smaller-scale bedforms. Our goal is to understand physical limitations on bar growth and geometry, with implications for interpreting the rock record and predicting physically-driven riverine habitat variables.

Predictions for the $$\\bar{B}^{0}\\rightarrow \\bar{K}^{\\ast 0}$$ X(YZ) and $$\\bar{B}^{0}_{s}\\rightarrow\\phi$$ X(YZ) with X(4160), Y(3940), Z(3930)

DOE PAGES

Liang, Wei -Hong; Molina, R.; Xie, Ju -Jun; ...

2015-05-22

We investigate the decay ofmore » $$\\bar B^0 \\to \\bar K^{*0} R$$ and $$\\bar B^0_s \\to \\phi R$$ with $R$ being the $X(4160)$, $Y(3940)$, $Z(3930)$ resonances. Under the assumption that these states are dynamically generated from the vector-vector interaction, as has been concluded from several theoretical studies, we use a reaction mechanism of quark production at the elementary level, followed by hadronization of one final $$q \\bar q$$ pair into two vectors and posterior final state interaction of this pair of vector mesons to produce the resonances. With this procedure we are able to predict five ratios for these decays, which are closely linked to the dynamical nature of these states, and also predict the order of magnitude of the branching ratios which we find of the order of $$10^{-4}$$, well within the present measurable range. In order to further test the dynamical nature of these resonances we study the $$\\bar B^0_s \\to \\phi D^* \\bar D^*$$ and $$\\bar B^0_s \\to \\phi D_s^* \\bar D_s^*$$ decays close to the $$D^* \\bar D^*$$ and $$D_s^* \\bar D_s^*$$ thresholds and make predictions for the ratio of the mass distributions in these decays and the $$\\bar B^0_s \\to \\phi R$$ decay widths. In conclusion, the measurement of these decays rates can help unravel the nature of these resonances.« less

Deciphering the Possible Role of Strain Path on the Evolution of Microstructure, Texture, and Magnetic Properties in a Fe-Cr-Ni Alloy

NASA Astrophysics Data System (ADS)

Kumar, Amit; Khatirkar, Rajesh Kisni; Gupta, Aman; Shekhawat, Satish K.; Suwas, Satyam

2018-06-01

In the present work, the influence of strain path on the evolution of microstructure, crystallographic texture, and magnetic properties of a two-phase Fe-Cr-Ni alloy was investigated. The Fe-Cr-Ni alloy had nearly equal proportion of austenite and ferrite and was cold rolled up to a true strain of 1.6 (thickness reduction) using two different strain paths—unidirectional rolling and multi-step cross rolling. The microstructures were characterized by scanning electron microscopy (SEM) and electron backscattered diffraction (EBSD), while crystallographic textures were determined using X-ray diffraction. For magnetic characterization, B-H loops and M-H curves were measured and magnetic force microscopy was performed. After unidirectional rolling, ferrite showed the presence of strong α-fiber (rolling direction, RD//<110>) and austenite showed strong brass type texture (consisting of Brass (Bs) ({110}<112>), Goss ({110}<001>), and S ({123}<634>)). After multi-step cross rolling, strong rotated cube ({100}<110>) was developed in ferrite, while austenite showed ND (normal direction) rotated brass ( 10 deg) texture. The strain-induced martensite (SIM) was found to be higher in unidirectionally rolled samples than multi-step cross-rolled samples. The coherently diffracting domain size, micro-strain, coercivity, and core loss also showed a strong correlation with strain and strain path. More strain was partitioned into austenite than ferrite during deformation (unidirectional as well as cross rolling). Further, the strain partitioning (in both austenite and ferrite) was found to be higher in unidirectionally rolled samples.

On the role of impermeable groins on barred beach morphodynamics: Example of Matalascañas beach, Spain

NASA Astrophysics Data System (ADS)

Sedrati, Mouncef; Morales González, Juan Antonio

2017-04-01

Several studies on barred beaches in settings with mesotidal to macrotidal regimes have focused on cross-shore and alongshore bar mobility. Whereas the general link between hydrodynamics, sediment transport and the response of the intertidal bars and shoreline evolution has been recognized in the literature, the role of coastal defense structures (Breakwaters, groins, seawalls) on bar-trough systems morphodynamics have received more much less attention and the field-based experimental studies of these environments are rare. The main aim of this paper is to highlight the contrasting behavior of a natural and protected barred beach under several hydrodynamics conditions. This paper presents detailed hydrodynamic and morphological data from a field experiment spanning 10 days undertaken in Matalascañas beach, a mesotidal protected vs natural barred beach in the Southern Spanish coast. This mesotidal beach experienced intense erosion in the recent past and therefore it has been partially protected by groins (protection of sea-front touristic residences). During the fieldwork, an intertidal bars in the protected and non-protected areas highlighted contrasting morphological behaviour. The non-protected barred beach shows a less pronounced bar-trough system than the protected zone. Under low energy conditions (significant wave height < 0,6m), onshore bar migration rate in the protected area was more important than the non-protected area. This migration was associated with an onshore sediment transport, resulting from the erosion of the bar's seaward slope. In the same moment, a clear longshore bar migration was observed in the non-protected zone with the absence of this process in the protected zone. During few energetic tides (Significant wave height > 1m), the protected and non-protected zones show a flattening bars processes. The findings of the present study suggest that cross-shore vs longshore bar mobility may even be mitigated by the presence of the groins, which favour onshore than longshore bar migration.

Some Effects of Roll Rate on the Longitudinal Stability Characteristics of a Cruciform Missile Configuration as Determined from Flight Test for a Mach Number Range of 1.1. to 1.8

NASA Technical Reports Server (NTRS)

Lundstrom, Reginald R; Baber, Hal T , Jr

1956-01-01

A model of a cruciform missile configuration having a low-aspect-ratio wing equipped with flap-type controls was flight tested in order to determine stability and control characteristics while rolling at about 5 radians per second. Comparison is made with results from a similar model which rolled at a much lower rate. Results showed that, if the ratio of roll rate to natural circular frequency in pitch is not greater than about 0.3, the motion following a step disturbance in pitch essentially remains in a plane in space. The slope of normal- force coefficient against angle of attack C(sub N(sub alpha)) was the same as for the slowly rolling model at 0 degrees control deflection but C(sub N(sub alpha)) was much higher for the faster rolling model at about 5 degrees control deflection. The slope of pitching-moment coefficient against angle of attack C(sub m(sub alpha)) as determined from the model period of oscillation was the same for both models at 0 degrees control deflection but was lower for the faster rolling model at about 5 degrees control deflection. Damping data for the faster rolling model showed considerably more scatter than for the slowly rolling model.

An Automatic Braking System That Stabilizes Leukocyte Rolling by an Increase in Selectin Bond Number with Shear

PubMed Central

Chen, Shuqi; Springer, Timothy A.

1999-01-01

Wall shear stress in postcapillary venules varies widely within and between tissues and in response to inflammation and exercise. However, the speed at which leukocytes roll in vivo has been shown to be almost constant within a wide range of wall shear stress, i.e., force on the cell. Similarly, rolling velocities on purified selectins and their ligands in vitro tend to plateau. This may be important to enable rolling leukocytes to be exposed uniformly to activating stimuli on endothelium, independent of local hemodynamic conditions. Wall shear stress increases the rate of dissociation of individual selectin–ligand tether bonds exponentially (1, 4) thereby destabilizing rolling. We find that this is compensated by a shear-dependent increase in the number of bonds per rolling step. We also find an increase in the number of microvillous tethers to the substrate. This explains (a) the lack of firm adhesion through selectins at low shear stress or high ligand density, and (b) the stability of rolling on selectins to wide variation in wall shear stress and ligand density, in contrast to rolling on antibodies (14). Furthermore, our data successfully predict the threshold wall shear stress below which rolling does not occur. This is a special case of the more general regulation by shear of the number of bonds, in which the number of bonds falls below one. PMID:9885254

Separable requirements for cytoplasmic domain of PSGL-1 in leukocyte rolling and signaling under flow

PubMed Central

Miner, Jonathan J.; Xia, Lijun; Yago, Tadayuki; Kappelmayer, János; Liu, Zhenghui; Klopocki, Arkadiusz G.; Shao, Bojing; McDaniel, J. Michael; Setiadi, Hendra; Schmidtke, David W.

2008-01-01

In inflamed venules, leukocytes use P-selectin glycoprotein ligand-1 (PSGL-1) to roll on P-selectin and E-selectin and to activate integrin αLβ2 (lymphocyte function-associated antigen-1, LFA-1) to slow rolling on intercellular adhesion molecule-1 (ICAM-1). Studies in cell lines have suggested that PSGL-1 requires its cytoplasmic domain to localize in membrane domains, to support rolling on P-selectin, and to signal through spleen tyrosine kinase (Syk). We generated “ΔCD” mice that express PSGL-1 without the cytoplasmic domain. Unexpectedly, neutrophils from these mice localized PSGL-1 normally in microvilli, uropods, and lipid rafts. ΔCD neutrophils expressed less PSGL-1 on their surfaces because of inefficient export from the endoplasmic reticulum. Limited digestion of wild-type neutrophils with O-sialoglycoprotein endopeptidase was used to reduce the PSGL-1 density to that on ΔCD neutrophils. At matched PSGL-1 densities, both ΔCD and wild-type neutrophils rolled similarly on P-selectin. However, ΔCD neutrophils rolling on P-selectin did not trigger Syk-dependent activation of LFA-1 to slow rolling on ICAM-1. These data demonstrate that the PSGL-1 cytoplasmic domain is dispensable for leukocyte rolling on P-selectin but is essential to activate β2 integrins to slow rolling on ICAM-1. PMID:18550846

E-selectin engages PSGL-1 and CD44 through a common signaling pathway to induce integrin alphaLbeta2-mediated slow leukocyte rolling.

PubMed

Yago, Tadayuki; Shao, Bojing; Miner, Jonathan J; Yao, Longbiao; Klopocki, Arkadiusz G; Maeda, Kenichiro; Coggeshall, K Mark; McEver, Rodger P

2010-07-22

In inflamed venules, neutrophils rolling on E-selectin induce integrin alpha(L)beta(2)-dependent slow rolling on intercellular adhesion molecule-1 by activating Src family kinases (SFKs), DAP12 and Fc receptor-gamma (FcRgamma), spleen tyrosine kinase (Syk), and p38. E-selectin signaling cooperates with chemokine signaling to recruit neutrophils into tissues. Previous studies identified P-selectin glycoprotein ligand-1 (PSGL-1) as the essential E-selectin ligand and Fgr as the only SFK that initiate signaling to slow rolling. In contrast, we found that E-selectin engagement of PSGL-1 or CD44 triggered slow rolling through a common, lipid raft-dependent pathway that used the SFKs Hck and Lyn as well as Fgr. We identified the Tec kinase Bruton tyrosine kinase as a key signaling intermediate between Syk and p38. E-selectin engagement of PSGL-1 was dependent on its cytoplasmic domain to activate SFKs and slow rolling. Although recruiting phosphoinositide-3-kinase to the PSGL-1 cytoplasmic domain was reported to activate integrins, E-selectin-mediated slow rolling did not require phosphoinositide-3-kinase. Studies in mice confirmed the physiologic significance of these events for neutrophil slow rolling and recruitment during inflammation. Thus, E-selectin triggers common signals through distinct neutrophil glycoproteins to induce alpha(L)beta(2)-dependent slow rolling.

An automatic braking system that stabilizes leukocyte rolling by an increase in selectin bond number with shear.

PubMed

Chen, S; Springer, T A

1999-01-11

Wall shear stress in postcapillary venules varies widely within and between tissues and in response to inflammation and exercise. However, the speed at which leukocytes roll in vivo has been shown to be almost constant within a wide range of wall shear stress, i.e., force on the cell. Similarly, rolling velocities on purified selectins and their ligands in vitro tend to plateau. This may be important to enable rolling leukocytes to be exposed uniformly to activating stimuli on endothelium, independent of local hemodynamic conditions. Wall shear stress increases the rate of dissociation of individual selectin-ligand tether bonds exponentially (, ) thereby destabilizing rolling. We find that this is compensated by a shear-dependent increase in the number of bonds per rolling step. We also find an increase in the number of microvillous tethers to the substrate. This explains (a) the lack of firm adhesion through selectins at low shear stress or high ligand density, and (b) the stability of rolling on selectins to wide variation in wall shear stress and ligand density, in contrast to rolling on antibodies (). Furthermore, our data successfully predict the threshold wall shear stress below which rolling does not occur. This is a special case of the more general regulation by shear of the number of bonds, in which the number of bonds falls below one.

75 FR 801 - Airworthiness Directives; Rolls-Royce plc RB211-Trent 500, 700, and 800 Series Turbofan Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-06

...-0674; Directorate Identifier 2009-NE-25-AD] RIN 2120-AA64 Airworthiness Directives; Rolls-Royce plc... airworthiness directive (AD) for Rolls-Royce plc RB211-Trent 800 series turbofan engines. That AD currently... through Friday, except Federal holidays. Fax: (202) 493-2251. Contact Rolls-Royce plc, P.O. Box 31, DERBY...

75 FR 264 - Airworthiness Directives; Rolls-Royce plc RB211-Trent 800 Series Turbofan Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-05

...-1004; Directorate Identifier 2009-NE-36-AD] RIN 2120-AA64 Airworthiness Directives; Rolls-Royce plc.... Contact Rolls-Royce plc, P.O. Box 31, Derby, England; telephone: 011-44-1332-249428; fax: 011-44-1332... condition may exist on Rolls-Royce plc RB211 Trent 800 series turbofan engines. The MCAI states: During 2004...

75 FR 17630 - Airworthiness Directives; Rolls-Royce plc RB211 Trent 700 and Trent 800 Series Turbofan Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-07

...-0364; Directorate Identifier 2009-NE-27-AD] RIN 2120-AA64 Airworthiness Directives; Rolls-Royce plc... Service Information Rolls-Royce plc has issued Alert Service Bulletin RB.211-72-AG086, dated December 4... adding the following new AD: Rolls-Royce plc: Docket No. FAA-2010-0364; Directorate Identifier 2009-NE-27...

75 FR 61114 - Airworthiness Directives; Rolls-Royce plc RB211-Trent 800 Series Turbofan Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-04

... Airworthiness Directives; Rolls-Royce plc RB211-Trent 800 Series Turbofan Engines AGENCY: Federal Aviation.... Fax: (202) 493-2251. Contact Rolls-Royce plc, P.O. Box 31, Derby, England, DE248BJ; telephone: 011-44... proposed AD, for Rolls- Royce plc RB211-Trent 800 series turbofan engines. That proposed AD would have...

76 FR 72650 - Airworthiness Directives; Rolls-Royce plc (RR) RB211 Trent 800 Series Turbofan Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-25

...-0959; Directorate Identifier 2011-NE-25-AD] RIN 2120-AA64 Airworthiness Directives; Rolls-Royce plc (RR... holidays. Fax: (202) 493-2251. Contact Rolls-Royce plc, P.O. Box 31, Derby, DE24 8BJ, United Kingdom; phone... airplane. Relevant Service Information Rolls-Royce plc has issued Alert Service Bulletin RB.211-72-AG456...

75 FR 15321 - Airworthiness Directives; Rolls-Royce plc RB211-Trent 800 Series Turbofan Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-29

... Directives; Rolls-Royce plc RB211-Trent 800 Series Turbofan Engines AGENCY: Federal Aviation Administration... Rolls-Royce plc: Amendment 39-16239. Docket No. FAA-2009- 1004; Directorate Identifier 2009-NE-36-AD.... Applicability (c) This AD applies to Rolls-Royce plc models RB211-Trent 875- 17, Trent 877-17, Trent 884-17...

Analysis of rolling fracture of the conticasted and tandem rolled blanks of low alloyed aluminum

NASA Astrophysics Data System (ADS)

Li, Yong; Zeng, Lingping; Jiao Xie, Xian

2018-01-01

Optical microscopy, electron microscopy and energy spectrum were used to test the morphology of grains, as-cast microstructure and secondary phases in confiscated and tandem rolled planks of 8011 low alloying aluminum alloy. It can be concluded that the existence of inhomogeneous secondary FeSiAl phases lead to the fracture of planks during rolling.

Simple Model of a Rolling Water-Filled Bottle on an Inclined Ramp

ERIC Educational Resources Information Center

Lin, Shihao; Hu, Naiwen; Yao, Tianchen; Chu, Charles; Babb, Simona; Cohen, Jenna; Sangiovanni, Giana; Watt, Summer; Weisman, Danielle; Klep, James; Walecki, Wojciech J.; Walecki, Eve S.; Walecki, Peter S.

2015-01-01

We investigate a water-filled bottle rolling down an incline and ask the following question: is a rolling bottle better described by a model ignoring all internal motion where the bottle is approximated by a material point sliding down an incline, or is it better described by a rigid solid cylinder rolling down the incline without skidding? The…

49 CFR 393.122 - What are the rules for securing paper rolls?

Code of Federal Regulations, 2010 CFR

2010-10-01

... be loaded on a layer of paper rolls beneath unless the lower layer extends to the front of the vehicle. (2) Paper rolls in the second and subsequent layers must be prevented from forward, rearward or lateral movement by means as allowed for the bottom layer, or by use of a blocking roll from a lower layer...

77 FR 41374 - Certain Hot-Rolled Carbon Steel Flat Products From India: Notice of Court Decision Not in Harmony...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-13

... 14, 2011) (opinion on final results) (U.S. Steel Corp. I); Certain Hot- Rolled Carbon Steel Flat... DEPARTMENT OF COMMERCE International Trade Administration [A-533-820] Certain Hot-Rolled Carbon...-rolled carbon steel flat products from India. See U.S. Steel Corp. v. United States, No. 08-00216, 2012...

Material-Process-Performance Relationships for Roll-to-Roll Coated PEM Electrodes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mauger, Scott; Neyerlin, K.C.; Stickel, Jonathan

2017-04-26

Roll-to-roll (R2R) coating is the most economical and highest throughput method for producing fuel cell electrodes. R2R coating encompasses many different methodologies to create uniform films on a moving web substrate. Here we explore two coating methods, gravure and slot die, to understand the impacts of each on film uniformity and performance.

78 FR 67320 - Special Conditions: Airbus, Model A350-900 series Airplane; Pitch and Roll Limiting by Electronic...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-12

...) associated with the Electronic Flight Control System that limits pitch and roll attitude functions. The... substantiate the pitch and roll attitude limiting functions and the appropriateness of the chosen limits. Type... attitudes greater than +30 degrees and less than -15 degrees, and roll angles greater than plus or minus 67...

Bearing selection in ball-rolling dung beetles: is it constant?

PubMed

Baird, Emily; Byrne, Marcus J; Scholtz, Clarke H; Warrant, Eric J; Dacke, Marie

2010-11-01

Ball rolling in dung beetles is thought to have evolved as a means to escape intense inter- and intra-specific competition at the dung pile. Accordingly, dung beetles typically roll along a straight-line path away from the pile, this being the most effective escape strategy for transporting dung to a suitable burial site. In this study, we investigate how individual diurnal dung beetles, Scarabaeus (Kheper) nigroaeneus, select the compass bearing of their straight-line rolls. In particular, we examine whether roll bearings are constant with respect to geographic cues, celestial cues, or other environmental cues (such as wind direction). Our results reveal that the roll bearings taken by individual beetles are not constant with respect to geographic or celestial references. Environmental cues appear to have some influence over bearing selection, although the relationship is not strong. Furthermore, the variance in roll bearing that we observe is not affected by the presence or absence of other beetles. Thus, rather than being constant for individual beetles, bearing selection varies each time a beetle makes a ball and rolls it away from the dung pile. This strategy allows beetles to make an efficient escape from the dung pile while minimizing the chance of encountering competition.

Judging rolling wheels: Dynamic and kinematic aspects of rotation-translation coupling

NASA Technical Reports Server (NTRS)

Hecht, Heiko

1993-01-01

Four experiments were carried out to investigate observers' abilities to judge rolling motions. The experiments were designed to assess whether two important aspects of such motions are appreciated: the kinematic coupling of rotation and translation, and the dynamic effects of gravity. Different motion contexts of rolling wheels were created using computer-generated displays. The first experiment involved wheels rolling down an inclined plane. Observers spontaneously appreciated the anomaly of wheels that failed to accelerate, but they were not able to differentiate between different acceleration functions. Moreover, their judgements were almost exclusively based on the translation component of the rolling motion, neglecting the rotation component. In a second experiment it was found that observers could accurately estimate the perimeter of various objects. Thus, their inability to consider rotation information is not attributable to misperceptions of the geometry of wheels. In a third experiment the finding that rolling wheels appear to overrotate was replicated; however, findings from this experiment also showed, together with those from a fourth experiment, that observers are able to make very accurate judgments about translation-rotation coupling in rolling wheels when information is provided about the orientation of the wheel and the texture of the surface on which it rolls.

Judging rolling wheels: dynamic and kinematic aspects of rotation-translation coupling.

PubMed

Hecht, H

1993-01-01

Four experiments were carried out to investigate observers' abilities to judge rolling motions. The experiments were designed to assess whether two important aspects of such motions are appreciated: the kinematic coupling of rotation and translation, and the dynamic effects of gravity. Different motion contexts of rolling wheels were created using computer-generated displays. The first experiment involved wheels rolling down an inclined plane. Observers spontaneously appreciated the anomaly of wheels that failed to accelerate, but they were not able to differentiate between different acceleration functions. Moreover, their judgments were almost exclusively based on the translation component of the rolling motion, neglecting the rotation component. In a second experiment it was found that observers could accurately estimate the perimeter of various objects. Thus, their inability to consider rotation information is not attributable to misperceptions of the geometry of wheels. In a third experiment the finding that rolling wheels appear to overrotate was replicated; however, findings from this experiment also showed, together with those from a fourth experiment, that observers are able to make very accurate judgments about translation-rotation coupling in rolling wheels when information is provided about the orientation of the wheel and the texture of the surface on which it rolls.

Hot forging of roll-cast high aluminum content magnesium alloys

NASA Astrophysics Data System (ADS)

Kishi, Tomohiro; Watari, Hisaki; Suzuki, Mayumi; Haga, Toshio

2017-10-01

This paper reports on hot forging of high aluminum content magnesium alloy sheets manufactured using horizontal twin-roll casting. AZ111 and AZ131 were applied for twin-roll casting, and a hot-forging test was performed to manufacture high-strength magnesium alloy components economically. For twin-roll casting, the casting conditions of a thick sheet for hot forging were investigated. It was found that twin-roll casting of a 10mm-thick magnesium alloy sheet was possible at a roll speed of 2.5m/min. The grain size of the cast strip was 50 to 70µm. In the hot-forging test, blank material was obtained from as-cast strip. A servo press machine with a servo die cushion was used to investigate appropriate forging conditions (e.g., temperature, forging load, and back pressure) for twin-roll casts (TRCs) AZ111 and AZ131. It was determined that high aluminum content magnesium alloy sheets manufactured using twin-roll casting could be forged with a forging load of 150t and a back pressure of 3t at 420 to 430°C. Applying back pressure during hot forging effectively forged a pin-shaped product.

Rolled-up transformer structure for a radiofrequency integrated circuit (RFIC)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Xiuling; Huang, Wen

A rolled-up transformer structure comprises a multilayer sheet having a rolled configuration comprising multiple turns about a longitudinal axis. The multilayer sheet comprises more than one conductive pattern layer on a strain-relieved layer, including a first conductive film and a second conductive film separated from the first conductive film in a thickness direction. The first conductive film comprises an even number of primary conductive strips, where each primary conductive strip has a length extending in the rolling direction, and the second conductive film comprises an even number of secondary conductive strips, where each secondary conductive strip has a length extendingmore » in the rolling direction. In the rolled configuration, turns of the primary conductive strips and turns of the secondary conductive strips wrap around the longitudinal axis. The primary conductive strips serve as a primary winding and the secondary conductive strips serve as a secondary winding of the rolled-up transformer structure.« less

Adaptive wing static aeroelastic roll control

NASA Astrophysics Data System (ADS)

Ehlers, Steven M.; Weisshaar, Terrence A.

1993-09-01

Control of the static aeroelastic characteristics of a swept uniform wing in roll using an adaptive structure is examined. The wing structure is modeled as a uniform beam with bending and torsional deformation freedom. Aerodynamic loads are obtained from strip theory. The structure model includes coefficients representing torsional and bending actuation provided by embedded piezoelectric material layers. The wing is made adaptive by requiring the electric field applied to the piezoelectric material layers to be proportional to the wing root loads. The proportionality factor, or feedback gain, is used to control static aeroelastic rolling properties. Example wing configurations are used to illustrate the capabilities of the adaptive structure. The results show that rolling power, damping-in-roll and aileron effectiveness can be controlled by adjusting the feedback gain. And that dynamic pressure affects the gain required. Gain scheduling can be used to set and maintain rolling properties over a range of dynamic pressures. An adaptive wing provides a method for active aeroelastic tailoring of structural response to meet changing structural performance requirements during a roll maneuver.

Roll Casting of Aluminum Alloy Clad Strip

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nakamura, R.; Tsuge, H.; Haga, T.

2011-01-17

Casting of aluminum alloy three layers of clad strip was tried using the two sets of twin roll casters, and effects of the casting parameters on the cladding conditions were investigated. One twin roll caster was mounted on the other twin roll caster. Base strip was 8079 aluminum alloy and overlay strips were 6022 aluminum alloy. Effects of roll-load of upper and lower casters and melt temperature of the lower caster were investigated. When the roll-load of the upper and lower caster was large enough, the overlay strip could be solidified and be connected. The overlay strip could be connectedmore » when the melt of the overlay strip cast by the lower caster was low enough. Sound three layers of clad strip could be cast by proper conditions.« less

The effect of thermomechanical processing on second phase particle redistribution in U-10 wt%Mo

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hu, Xiaohua; Wang, Xiaowo; Joshi, Vineet V.

2018-03-01

The multi-pass hot-rolling process of an annealed uranium-10 wt% molybdenum coupon was studied by plane-strain compression finite element modeling. Two point correlation function (2PCF) was used to analyze the carbide particle distribution after each rolling reduction. The hot rolling simulation results show that the alignment of UC particles along grain boundaries will rotate during rolling until it is parallel to the rolling direction, to form stringer-like distributions which are typically observed in rolled products that contain inclusions. 2PCF analysis of simulation shows that the interparticle spacing shrinks along the normal direction. The number of major peaks of 2PCF along NDmore » decreases after large reduction. The locations of major peaks indicate the inter-stringer distances.« less

Rolled-out collectors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shurcliff, W.A.

1979-04-01

SolaRoll is a solar collector material composed of extruded strips of black ethylene propylene diene monomer (EPDM) that is suitable for water or air type collectors. SolaRoll is provided in rolls and consists of an absorber mat with tubes and fins and a framing strip comprising all the parts of the collector frame. The rolls are bent in a counterflow pattern to cover the entire collector area and the mat is fastened with a thermosetting mastic adhesive. The heat transfer fluid is plain water as freezing does not injure the EPDM. Installation of the glazing in the framing strip ismore » described. EPDM has the disadvantage of low thermal conductivity but its use does not require antifreeze or a heat exchanger. Design options and suitable applications of SolaRoll systems are discussed.« less

32 CFR 776.66 - Bar admission and disciplinary matters.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 5 2010-07-01 2010-07-01 false Bar admission and disciplinary matters. 776.66... ADVOCATE GENERAL Rules of Professional Conduct § 776.66 Bar admission and disciplinary matters. (a) Bar admission and disciplinary matters. A covered attorney, in connection with any application for bar admission...

Searches for Higgs boson(s) at the upgraded Tevatron

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bernardi, Gregorio; /Paris U., VI-VII /Fermilab

2005-07-01

We summarize the status of Higgs boson searches at the upgraded Fermilab Tevatron performed by the D0 and CDF collaborations. We report on three categories of searches, namely the search for the Standard Model Higgs boson (p{bar p} {yields} H, WH or ZH, with H {yields} WW* and/or H {yields} b{bar b}), the search for the minimal supersymmetric Higgs boson using p{bar p} {yields} hb{bar b} {yields} b{bar b}b{bar b} and p{bar p} {yields} hX {yields} {tau}{tau}X, and the search for doubly charged Higgs boson.

Polymorphic transformation of dense ZnO nanoparticles: Implications for chair/boat-type Peierls distortions of AB semiconductor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, S.-Y.; Shen Pouyan; Jiang Jianzhong

2004-12-08

Peierls distortion path was proved experimentally for dense ZnO nanoparticles prepared by static compression. Electron irradiation caused rock salt (R) to wurtzite (W) transition, following preferential (11-bar1){sub R}//(01-bar11){sub W}; [011]{sub R}//[1-bar21-bar3]{sub W} and then transformation strain induced (111-bar){sub R}//(1-bar011){sub W}; [011]{sub R}//[011-bar1]{sub W}. The two relationships can be rationalized by specified extent of chair- and boat-type Peierls distortions accompanied with band gap opening and intermediate {l_brace}111{r_brace}{sub R} slip for energetically favorable {l_brace}111{r_brace}{sub R}/(01-bar11){sub W} match.

Salt Bridge Formation between the I-BAR Domain and Lipids Increases Lipid Density and Membrane Curvature.

PubMed

Takemura, Kazuhiro; Hanawa-Suetsugu, Kyoko; Suetsugu, Shiro; Kitao, Akio

2017-07-28

The BAR domain superfamily proteins sense or induce curvature in membranes. The inverse-BAR domain (I-BAR) is a BAR domain that forms a straight "zeppelin-shaped" dimer. The mechanisms by which IRSp53 I-BAR binds to and deforms a lipid membrane are investigated here by all-atom molecular dynamics simulation (MD), binding energy analysis, and the effects of mutation experiments on filopodia on HeLa cells. I-BAR adopts a curved structure when crystallized, but adopts a flatter shape in MD. The binding of I-BAR to membrane was stabilized by ~30 salt bridges, consistent with experiments showing that point mutations of the interface residues have little effect on the binding affinity whereas multiple mutations have considerable effect. Salt bridge formation increases the local density of lipids and deforms the membrane into a concave shape. In addition, the point mutations that break key intra-molecular salt bridges within I-BAR reduce the binding affinity; this was confirmed by expressing these mutants in HeLa cells and observing their effects. The results indicate that the stiffness of I-BAR is important for membrane deformation, although I-BAR does not act as a completely rigid template.

Comparison of Saccharomyces cerevisiae F-BAR domain structures reveals a conserved inositol phosphate binding site.

PubMed

Moravcevic, Katarina; Alvarado, Diego; Schmitz, Karl R; Kenniston, Jon A; Mendrola, Jeannine M; Ferguson, Kathryn M; Lemmon, Mark A

2015-02-03

F-BAR domains control membrane interactions in endocytosis, cytokinesis, and cell signaling. Although they are generally thought to bind curved membranes containing negatively charged phospholipids, numerous functional studies argue that differences in lipid-binding selectivities of F-BAR domains are functionally important. Here, we compare membrane-binding properties of the Saccharomyces cerevisiae F-BAR domains in vitro and in vivo. Whereas some F-BAR domains (such as Bzz1p and Hof1p F-BARs) bind equally well to all phospholipids, the F-BAR domain from the RhoGAP Rgd1p preferentially binds phosphoinositides. We determined X-ray crystal structures of F-BAR domains from Hof1p and Rgd1p, the latter bound to an inositol phosphate. The structures explain phospholipid-binding selectivity differences and reveal an F-BAR phosphoinositide binding site that is fully conserved in a mammalian RhoGAP called Gmip and is partly retained in certain other F-BAR domains. Our findings reveal previously unappreciated determinants of F-BAR domain lipid-binding specificity and provide a basis for its prediction from sequence. Copyright © 2015 Elsevier Ltd. All rights reserved.

Comparison of Saccharomyces cerevisiae F-BAR Domain Structures Reveals a Conserved Inositol Phosphate Binding Site

DOE PAGES

Moravcevic, Katarina; Alvarado, Diego; Schmitz, Karl R.; ...

2015-01-22

F-BAR domains control membrane interactions in endocytosis, cytokinesis, and cell signaling. Although they are generally thought to bind curved membranes containing negatively charged phospholipids, numerous functional studies argue that differences in lipid-binding selectivities of F-BAR domains are functionally important. Here in this paper, we compare membrane-binding properties of the Saccharomyces cerevisiae F-BAR domains in vitro and in vivo. Whereas some F-BAR domains (such as Bzz1p and Hof1p F-BARs) bind equally well to all phospholipids, the F-BAR domain from the RhoGAP Rgd1p preferentially binds phosphoinositides. We determined X-ray crystal structures of F-BAR domains from Hof1p and Rgd1p, the latter bound tomore » an inositol phosphate. The structures explain phospholipid-binding selectivity differences and reveal an F-BAR phosphoinositide binding site that is fully conserved in a mammalian RhoGAP called Gmip and is partly retained in certain other F-BAR domains. In conclusion, our findings reveal previously unappreciated determinants of F-BAR domain lipid-binding specificity and provide a basis for its prediction from sequence.« less

Changes in smoking-related norms in bars resulting from California's Smoke-Free Workplace Act.

PubMed

Satterlund, Travis D; Lee, Juliet P; Moore, Roland S

2012-01-01

California's Smoke-Free Workplace Act--CA Labor Code Sec. 6404.5(a)--was extended to bars in 1998. This article analyzes changes in normative beliefs and behaviors related to bar smoking in the decade following the adoption of the Act. In a series of studies evaluating the smoke-free workplace law in bars, researchers conducted extensive observations and interviews with bar staff and patrons, health officials, and law enforcement personnel in three California counties. Smoking outside became a normal pause in the social environment and created a new type of bar socializing for outside smokers. Although some bar owners and staff reported initially resenting the responsibility to uphold the law, once norms regarding cigarettes and smoking began changing, bar workers experienced less conflict in upholding the law. Non-smoking behavior within bars also became the normative behavior for bar patrons. California's Smoke-Free Workplace Act has both reflected and encouraged normative beliefs and behaviors related to smoking in bars. The findings indicate that such shifts are possible even in contexts where smoking behaviors and attitudes supporting smoking were deeply entrenched. Recommendations include attending to the synergistic effect of education and policy in effective tobacco control programs.

Bar Evolution and Bar Properties from Disc Galaxies in the Early Universe

NASA Astrophysics Data System (ADS)

Hutchinson-Smith, Tenley; Simmons, Brooke

2017-01-01

Bars in disc galaxies indicate a large collection of stars in a specific configuration of orbits that give the galaxy center a rectangular looking feature. Astronomers have discovered that these bars affect the distribution of matter in galaxies, and are also related to galaxy stellar mass and star formation history. Little is known about the specifics of how bars evolve and drive the evolution of their host galaxies because only a handful of bars have been studied in detail so far. I have examined a sample of 8,221 barred galaxies from the early universe to identify and examine correlations with galaxy properties. The data comes from Galaxy Zoo, an online citizen science project that allows anyone to classify and measure detailed properties of galaxies. I present results including the fraction of galaxies in the sample that have bars, and the variation of galaxy properties with bar length, including galaxy color and stellar mass. I also compare these results to barred galaxies in the local universe. I will discuss the implications of these results in the context of galaxy evolution overall, including the effect of dark matter on bars and galaxy evolution.

Snack bar compositions and their acute glycaemic and satiety effects.

PubMed

Yan, Mary R; Parsons, Andrew; Whalley, Gillian A; Kelleher, John; Rush, Elaine C

Maintaining blood glucose within homeostatic limits and eating foods that sup-press hunger and promote satiety have beneficial impacts for health. This study investigated the glycaemic re-sponse and satiety effects of a serving size of a healthier snack bar, branded Nothing Else, that met the required nutrient profiling score criteria for a health claim, in comparison to two top-selling commercial snack bars. In an experimental study, 24 participants aged >=50 years were recruited. On three different days blood glucose concentration was measured twice at baseline and 15, 30, 45, 60, 90 and 120 minutes after consumption of a serving size of each bar. Satiety effects were self-reported hunger, fullness, desire to eat, and amount could eat ratings on visual analogue scales. The incremental area under the blood glucose response curve (iAUC) over two hours for the Nothing Else bar was 30% lower than commercial Bar 2 (p<0.001). At 45 minutes after eating, the Nothing Else bar induced the highest fullness rating and lowest hunger rating among the three snack bars. At two hours, fullness induced by the Nothing Else bar was twice that of Bar 2 (p=0.019), but not different to Bar 1 (p=0.212). The Nothing Else snack bar developed using the nutrient profiling scheme as a guideline, with its high protein and dietary fibre contents, had a lower glycaemic impact and induced a higher subjective satiety than the two commercial snack bars of equal weight.

Reformulating cereal bars: high resistant starch reduces in vitro digestibility but not in vivo glucose or insulin response; whey protein reduces glucose but disproportionately increases insulin.

PubMed

Wolever, Thomas Ms; van Klinken, B Jan-Willem; Bordenave, Nicolas; Kaczmarczyk, Melissa; Jenkins, Alexandra L; Chu, YiFang; Harkness, Laura

2016-10-01

Resistant starch (RS) and whey protein are thought to be effective nutrients for reducing glycemic responses. We aimed to determine the effect of varying the sucrose, RS, and whey protein content of cereal bars on glucose and insulin responses. Twelve healthy subjects [mean ± SD age: 36 ± 12 y; mean ± SD body mass index (in kg/m 2 ): 24.9 ± 2.7] consumed 40 g available-carbohydrate (avCHO) portions of 5 whole-grain cereal bars that contained varying amounts of RS and whey protein concentrate [WPC; 70% protein; RS:WPC, %wt:wt: 15:0 (Bar15/0); 15:0, low in sucrose (Bar15/0LS); 15:5 (Bar15/5); 10:5 (Bar10/5); and 10:10 (Bar10/10)] and 2 portion sizes of a control bar low in whole grains, protein, and RS [control 1 contained 40 g avCHO (Control1); control 2 contained total carbohydrate equal to Bar15/0LS (Control2)] on separate days by using a randomized crossover design. Glucose and insulin responses in vivo and carbohydrate digestibility in vitro were measured over 3 h. Incremental area under the curve (iAUC) over 0-3 h for glucose (min × mmol/L) differed significantly between treatments (P < 0.001) [Bar15/0LS (mean ± SEM), 169 ± 14; Control2, 164 ± 20; Bar15/0, 144 ± 15; Control1, 140 ± 17; Bar10/5, 117 ± 12; Bar15/5, 116 ± 9; and Bar10/10, 100 ± 9; Tukey's least significant difference = 42, P < 0.05], but insulin iAUC did not differ significantly. Higher protein content was associated with a lower glucose iAUC (P = 0.028) and a higher insulin-to-glucose iAUC ratio (P = 0.002) All 5 RS-containing bars were digested in vitro ∼30% more slowly than the control bars (P < 0.05); however, in vivo responses were not related to digestibility in vitro. Glucose and insulin responses elicited by high-RS, whey protein-free bars were similar to those elicited from control bars. The inclusion of RS in cereal bar formulations did not reduce glycemic responses despite slower starch digestion in vitro. Thus, caution is required when extrapolating in vitro starch digestibility to in vivo glycemic response. The inclusion of whey protein in cereal bar formulations to reduce glycemic response requires caution because this may be associated with a disproportionate increase in insulin as judged by an increased insulin-to-glucose iAUC ratio. This trial was registered at clinicaltrials.gov as NCT02537587. © 2016 American Society for Nutrition.

35. RW Meyer Sugar Mill: 18761889. Threeroll sugar mill, oneton ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

35. RW Meyer Sugar Mill: 1876-1889. Three-roll sugar mill, one-ton daily processing capacity. Manufactured by Edwin Maw, Liverpool, England, ca. 1855-1870. View: Bevel gear at lower end of vertical drive shaft in foreground turned bevel gear of top roll when the vertical drive shaft was in place in the brass-bearing socket in the middle ground of the photograph. The bolts above the top roll and at the side of the two bottom rolls adjusted the pressure and position of the rolls' brass bearings. - R. W. Meyer Sugar Mill, State Route 47, Kualapuu, Maui County, HI

Fabrication of thin bulk ceramics for microwave circulator applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ings, J.B.; Simmins, J.J.; May, J.L.

1995-09-01

Planer MMIC circulator applications require the production of thin, flat garnet, spinel, and hexagonal ferrite circulator elements. Fabrication of cira 250 {mu}m circulator elements was done by tape casting and roll compaction. For the garnet, tape cast gave equivalent results to roll compaction. For the spinel and hexaferrite materials, which undergo magnetic flocculation, roll compaction was found to be the preferred fabrication method. Roll compacted lithium ferrite resulted in higher densities and lower {triangle}H and tan{delta} than did the tape case material. Roll compacted barium hexaferrite resulted in higher densities and remanent magnetization than did the tape cast material.

Remote control canard missile with a free-rolling tail brake torque system

NASA Technical Reports Server (NTRS)

Blair, A. B., Jr.

1981-01-01

An experimental wind-tunnel investigation has been conducted at supersonic Mach numbers to determine the static aerodynamic characteristics of a cruciform canard-controlled missile with fixed and free-rolling tail-fin afterbodies. Mechanical coupling effects of the free-rolling tail afterbody were investigated using an electronic/electromagnetic brake system that provides arbitrary tail-fin brake torques with continuous measurements of tail-to-mainframe torque and tail-roll rate. Results are summarized to show the effects of fixed and free-rolling tail-fin afterbodies that include simulated measured bearing friction torques on the longitudinal and lateral-directional aerodynamic characteristics.

Biomechanical Factors and Injury Risk in High-Severity Rollovers

PubMed Central

Moore, Tara L. A.; Vijayakumar, Vinod; Steffey, Duane L.; Ramachandran, Karuna; Corrigan, Catherine Ford

2005-01-01

The number of rolls, as well as other factors, has been associated with increased injury risk in rollovers. Data from NASS-CDS from 1995–2003 were used to evaluate the biomechanical implications of vehicle kinematics during multiple rolls and to evaluate the risk of injuries to different body regions during rollovers. The data showed that the risk of injury increased with increasing number of rolls. The rate of increase in risk varied by the region of the body affected and injury severity. The increased risk was particularly great when a vehicle rolled more than two complete rolls. PMID:16179145

CMB quadrupole depression produced by early fast-roll inflation: Monte Carlo Markov chains analysis of WMAP and SDSS data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Destri, C.; Vega, H. J. de; Observatoire de Paris, LERMA, Laboratoire Associe au CNRS UMR 8112, 61, Avenue de l'Observatoire, 75014 Paris

Generically, the classical evolution of the inflaton has a brief fast-roll stage that precedes the slow-roll regime. The fast-roll stage leads to a purely attractive potential in the wave equations of curvature and tensor perturbations (while the potential is purely repulsive in the slow-roll stage). This attractive potential leads to a depression of the CMB quadrupole moment for the curvature and B-mode angular power spectra. A single new parameter emerges in this way in the early universe model: the comoving wave number k{sub 1} characteristic scale of this attractive potential. This mode k{sub 1} happens to exit the horizon preciselymore » at the transition from the fast-roll to the slow-roll stage. The fast-roll stage dynamically modifies the initial power spectrum by a transfer function D(k). We compute D(k) by solving the inflaton evolution equations. D(k) effectively suppresses the primordial power for k

One year of smokefree bars and restaurants in New Zealand: impacts and responses.

PubMed

Thomson, George; Wilson, Nick

2006-03-14

New Zealand introduced a smokefree bars and restaurants policy in December 2004. We reviewed the data available at December 2005 on the main public health, societal and political impacts and responses within New Zealand to the new law. Data were collected from publicly available survey reports, and from government departments and interviews. This included data on smoking in bars, attitudes to smokefree bars, bar patronage, socially cued smoking, and perceived rights to smokefree workplaces. The proportion of surveyed bars with smoking occurring decreased from 95% to 3% during July 2004-April 2005. Between 2004 and 2005, public support for smokefree bars rose from 56% to 69%. In the same period, support for the rights of bar workers to have smokefree workplaces rose from 81% to 91%. During the first ten months of the smokefree bars policy, there were only 196 complaints to officials about smoking in the over 9900 licensed premises. The proportion of smokers who reported that they smoked more than normal at bars, nightclubs, casinos and cafés halved between 2004 and 2005 (from 58% to 29%). Seasonally adjusted sales in bars and clubs changed little (0.6% increase) between the first three quarters of 2004 and of 2005, while café and restaurant sales increased by 9.3% in the same period. Both changes continued existing trends. Compared to the same period in 2004, average employment during the first three quarters of 2005 was up 24% for 'pubs, taverns and bars', up 9% for cafés/restaurants, and down 8% for clubs (though employment in 'pubs, taverns and bars' may have been affected by unusually high patronage around a major sports-series). The proportion of bar managers who approved of smokefree bars increased from 44% to 60% between November 2004 and May 2005. Bar managers also reported increased agreement with the rights of bar workers and patrons to smokefree environments. The main reported concerns of the national and regional Hospitality Associations, in 2005, were the perceived negative effects on rural and traditional pubs. As in other jurisdictions, the introduction of smokefree bars in New Zealand has had positive overall health protection, economic and social effects; in contrast to the predictions of opponents.

One year of smokefree bars and restaurants in New Zealand: Impacts and responses

PubMed Central

Thomson, George; Wilson, Nick

2006-01-01

Background New Zealand introduced a smokefree bars and restaurants policy in December 2004. We reviewed the data available at December 2005 on the main public health, societal and political impacts and responses within New Zealand to the new law. Methods Data were collected from publicly available survey reports, and from government departments and interviews. This included data on smoking in bars, attitudes to smokefree bars, bar patronage, socially cued smoking, and perceived rights to smokefree workplaces. Results The proportion of surveyed bars with smoking occurring decreased from 95% to 3% during July 2004 – April 2005. Between 2004 and 2005, public support for smokefree bars rose from 56% to 69%. In the same period, support for the rights of bar workers to have smokefree workplaces rose from 81% to 91%. During the first ten months of the smokefree bars policy, there were only 196 complaints to officials about smoking in the over 9900 licensed premises. The proportion of smokers who reported that they smoked more than normal at bars, nightclubs, casinos and cafés halved between 2004 and 2005 (from 58% to 29%). Seasonally adjusted sales in bars and clubs changed little (0.6% increase) between the first three quarters of 2004 and of 2005, while café and restaurant sales increased by 9.3% in the same period. Both changes continued existing trends. Compared to the same period in 2004, average employment during the first three quarters of 2005 was up 24% for 'pubs, taverns and bars', up 9% for cafés/restaurants, and down 8% for clubs (though employment in 'pubs, taverns and bars' may have been affected by unusually high patronage around a major sports-series). The proportion of bar managers who approved of smokefree bars increased from 44% to 60% between November 2004 and May 2005. Bar managers also reported increased agreement with the rights of bar workers and patrons to smokefree environments. The main reported concerns of the national and regional Hospitality Associations, in 2005, were the perceived negative effects on rural and traditional pubs. Conclusion As in other jurisdictions, the introduction of smokefree bars in New Zealand has had positive overall health protection, economic and social effects; in contrast to the predictions of opponents. PMID:16533408

F-BAR family proteins, emerging regulators for cell membrane dynamic changes-from structure to human diseases.

PubMed

Liu, Suxuan; Xiong, Xinyu; Zhao, Xianxian; Yang, Xiaofeng; Wang, Hong

2015-05-09

Eukaryotic cell membrane dynamics change in curvature during physiological and pathological processes. In the past ten years, a novel protein family, Fes/CIP4 homology-Bin/Amphiphysin/Rvs (F-BAR) domain proteins, has been identified to be the most important coordinators in membrane curvature regulation. The F-BAR domain family is a member of the Bin/Amphiphysin/Rvs (BAR) domain superfamily that is associated with dynamic changes in cell membrane. However, the molecular basis in membrane structure regulation and the biological functions of F-BAR protein are unclear. The pathophysiological role of F-BAR protein is unknown. This review summarizes the current understanding of structure and function in the BAR domain superfamily, classifies F-BAR family proteins into nine subfamilies based on domain structure, and characterizes F-BAR protein structure, domain interaction, and functional relevance. In general, F-BAR protein binds to cell membrane via F-BAR domain association with membrane phospholipids and initiates membrane curvature and scission via Src homology-3 (SH3) domain interaction with its partner proteins. This process causes membrane dynamic changes and leads to seven important cellular biological functions, which include endocytosis, phagocytosis, filopodium, lamellipodium, cytokinesis, adhesion, and podosome formation, via distinct signaling pathways determined by specific domain-binding partners. These cellular functions play important roles in many physiological and pathophysiological processes. We further summarize F-BAR protein expression and mutation changes observed in various diseases and developmental disorders. Considering the structure feature and functional implication of F-BAR proteins, we anticipate that F-BAR proteins modulate physiological and pathophysiological processes via transferring extracellular materials, regulating cell trafficking and mobility, presenting antigens, mediating extracellular matrix degradation, and transmitting signaling for cell proliferation.

75 FR 27964 - Airworthiness Directives; Rolls-Royce plc (RR) RB211-22B and RB211-524 Series Turbofan Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-19

...-1157; Directorate Identifier 2009-NE-26-AD] RIN 2120-AA64 Airworthiness Directives; Rolls-Royce plc (RR... p.m., Monday through Friday, except Federal holidays. Fax: (202) 493-2251. Contact Rolls-Royce plc... Information Rolls-Royce plc has issued Alert Service Bulletin RB.211-72-AF336, dated October 24, 2007. The...

75 FR 61363 - Airworthiness Directives; Rolls-Royce plc RB211-524 Series, -535 Series, RB211 Trent 700 Series...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-05

...-0993; Directorate Identifier 2010-NE-08-AD] RIN 2120-AA64 Airworthiness Directives; Rolls-Royce plc... Federal holidays. Fax: (202) 493-2251. Contact Rolls-Royce plc, P.O. Box 31, Derby, DE24 8BJ, United... examining the MCAI in the AD docket. Relevant Service Information Rolls-Royce plc has issued Alert Service...

76 FR 12277 - Airworthiness Directives; Rolls-Royce plc RB211-Trent 768, 772, and 772B Turbofan Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-07

... Airworthiness Directives; Rolls-Royce plc RB211-Trent 768, 772, and 772B Turbofan Engines AGENCY: Federal...). Those ADs both require the same initial and repetitive visual inspections of Rolls-Royce plc RB211-Trent... FR 24911, May 6, 1998): 98-09-27R1 Rolls-Royce plc: Amendment 39-16620. Docket No. FAA-2010- 0960...

75 FR 69611 - Airworthiness Directives; Rolls-Royce plc RB211-Trent 768, 772, and 772B Turbofan Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-15

...-0960; Directorate Identifier 98-ANE-09-AD] RIN 2120-AA64 Airworthiness Directives; Rolls-Royce plc... repetitive visual inspections of Rolls-Royce plc RB211-Trent 768 and 772 series turbofan engine thrust... directive (AD) 98-09-27, Amendment 39-10508 (63 FR 24911, May 6, 1998): Rolls-Royce plc: Docket No. FAA-2010...

75 FR 58290 - Airworthiness Directives; Rolls-Royce plc RB211 Trent 700 and Trent 800 Series Turbofan Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-24

... Airworthiness Directives; Rolls-Royce plc RB211 Trent 700 and Trent 800 Series Turbofan Engines AGENCY: Federal...-20-11 Rolls-Royce plc: Amendment 39-16446. Docket No. FAA- 2010-0364; Directorate Identifier 2009-NE.... Affected ADs (b) None. Applicability (c) This AD applies to Rolls-Royce plc model (RR) RB211 Trent 768-60...

Establishing Linux Clusters for High-Performance Computing (HPC) at NPS

DTIC Science & Technology

2004-09-01

52 e. Intel Roll..................................................................................53 f. Area51 Roll...results of generating md5summ for Area51 roll. All the file information is available. This number can be used to be checked against the number that the...vendor provides fro the particular piece of software. ......51 Figure 22 The given md5summ for Area51 roll form the download site. This number can

Theoretical and Experimental Methods in the Solution of Missile Nonlinear Roll Problems

DTIC Science & Technology

1978-03-01

OF ILLUSTRATIONS (Continued) 34 Typical Effect of Slot on Induced Rolling Moment .............. 35 35 Effect of Slot on Amplitude of Induced Rolling...Characteristics of Slotted Fill Vehicle .............. 40 41 Effects of Fin Configuration on Stability ..................... 41 42 Release Envelope...missiles depended strongly upon roll rate. The concept of Magnus instability had been developed earlier from the linear theory of missile dynamics, and

Swiss roll nanomembranes with controlled proton diffusion as redox micro-supercapacitors.

PubMed

Ji, Hengxing; Mei, Yongfeng; Schmidt, Oliver G

2010-06-14

We demonstrate a redox Swiss roll micro-supercapacitor by rolling up a multilayered nanomembrane with an electrochemical active layer at either the outer or inner surface for different proton diffusion behaviors. The Swiss roll micro-supercapacitor could achieve high performance (e.g. capacity and life time) in a microscale power source and is helpful for studying charge transfer at the electrolyte/electrode interface.