Optimization of Surface Roughness and Wall Thickness in Dieless Incremental Forming Of Aluminum Sheet Using Taguchi

NASA Astrophysics Data System (ADS)

Hamedon, Zamzuri; Kuang, Shea Cheng; Jaafar, Hasnulhadi; Azhari, Azmir

2018-03-01

Incremental sheet forming is a versatile sheet metal forming process where a sheet metal is formed into its final shape by a series of localized deformation without a specialised die. However, it still has many shortcomings that need to be overcome such as geometric accuracy, surface roughness, formability, forming speed, and so on. This project focus on minimising the surface roughness of aluminium sheet and improving its thickness uniformity in incremental sheet forming via optimisation of wall angle, feed rate, and step size. Besides, the effect of wall angle, feed rate, and step size to the surface roughness and thickness uniformity of aluminium sheet was investigated in this project. From the results, it was observed that surface roughness and thickness uniformity were inversely varied due to the formation of surface waviness. Increase in feed rate and decrease in step size will produce a lower surface roughness, while uniform thickness reduction was obtained by reducing the wall angle and step size. By using Taguchi analysis, the optimum parameters for minimum surface roughness and uniform thickness reduction of aluminium sheet were determined. The finding of this project helps to reduce the time in optimising the surface roughness and thickness uniformity in incremental sheet forming.

Probabilistic Seismic Hazard Assessment for Iraq

DOE Office of Scientific and Technical Information (OSTI.GOV)

Onur, Tuna; Gok, Rengin; Abdulnaby, Wathiq

Probabilistic Seismic Hazard Assessments (PSHA) form the basis for most contemporary seismic provisions in building codes around the world. The current building code of Iraq was published in 1997. An update to this edition is in the process of being released. However, there are no national PSHA studies in Iraq for the new building code to refer to for seismic loading in terms of spectral accelerations. As an interim solution, the new draft building code was considering to refer to PSHA results produced in the late 1990s as part of the Global Seismic Hazard Assessment Program (GSHAP; Giardini et al.,more » 1999). However these results are: a) more than 15 years outdated, b) PGA-based only, necessitating rough conversion factors to calculate spectral accelerations at 0.3s and 1.0s for seismic design, and c) at a probability level of 10% chance of exceedance in 50 years, not the 2% that the building code requires. Hence there is a pressing need for a new, updated PSHA for Iraq.« less

Light Scattering from Rough Surfaces. Appendix. Angular Correlation of Speckle Patterns. Draft

DTIC Science & Technology

1994-06-01

For his demonstrations of the various experimental techniques, I owe thanks to Andrew Sant. Also, on behalf of all students writing (and written) up ...less controllable, radar set up . 1.1.1 Theoretical Models This section will present some of the theoretical models which exist for determining the...centre of a turntable set up to spin at :300 revolutions per minute. While the turntable is stationary, photoresist is applied to the centre of the

75 FR 6030 - EPA Science Advisory Board Staff Office Request for Nominations of Experts for the SAB Lead (Pb...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-05

... requesting public nominations of experts to form an SAB Ad Hoc Panel to review EPA's draft technical analyses... residential dust. OPPT is developing draft technical analyses that will be used to support: (a) Possible... that the SAB conduct a review of these draft technical analyses. The SAB was established by 42 U.S.C...

Draft reference grid cells for emergency response reconnaissance developed for use by the US Environmental Protection Agency [ER.QUADS6K_EPA

EPA Pesticide Factsheets

Draft reference grid cells for emergency response reconnaissance developed for use by the US Environmental Protection Agency. Grid cells are based on densification of the USGS Quarterquad (1:12,000 scale or 12K) grids for the continental United States, Alaska, Hawaii and Puerto Rico and are roughly equivalent to 1:6000 scale (6K) quadrangles approximately 2 miles long on each side. Note: This file is >80MB in size. Regional subsets have been created from this national file that include a 20 mile buffer of tiles around each EPA Region. To access the regional subsets, go to http://geodata.epa.gov/OSWER/6kquads_epa.zip and select the name of the file that corresponds to your region of interest (e.g. 6kquadr1.zip is the name of the file created for EPA Region 1).

Surface roughness formation during shot peen forming

NASA Astrophysics Data System (ADS)

Koltsov, V. P.; Vinh, Le Tri; Starodubtseva, D. A.

2018-03-01

Shot peen forming (SPF) is used for forming panels and skins, and for hardening. As a rule, shot peen forming is performed after milling. Surface roughness is a complex structure, a combination of an original microrelief and shot peen forming indentations of different depths and chaotic distribution along the surface. As far as shot peen forming is a random process, surface roughness resulted from milling and shot peen forming is random too. During roughness monitoring, it is difficult to determine the basic surface area which would ensure accurate results. It can be assumed that the basic area depends on the random roughness which is characterized by the degree of shot peen forming coverage. The analysis of depth and shot peen forming indentations distribution along the surface made it possible to identify the shift of an original center profile plane and create a mathematical model for the arithmetic mean deviation of the profile. Experimental testing proved model validity and determined an inversely proportional dependency of the basic area on the degree of coverage.

Draft Genome Sequences of 12 Dry-Heat-Resistant Bacillus Strains Isolated from the Cleanrooms Where the Viking Spacecraft Were Assembled

PubMed Central

Seuylemezian, Arman; Cooper, Kerry; Schubert, Wayne

2018-01-01

ABSTRACT Spore-forming microorganisms are of concern for forward contamination because they can survive harsh interplanetary travel. Here, we report the draft genome sequences of 12 spore-forming strains isolated from the Manned Spacecraft Operations Building (MSOB) and the Vehicle Assembly Building (VAB) in Cape Canaveral, FL, where the Viking spacecraft were assembled. PMID:29567731

76 FR 82306 - Draft Guidance for Industry on Use of Histology in Biomarker Qualification Studies; Availability

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-30

... evolution and reversibility of morphologic changes. Because of the many variations in the practice of..., and other forms of information technology. This draft guidance refers to previously approved...

Creative revision - From rough draft to published paper

NASA Technical Reports Server (NTRS)

Buehler, M. F.

1976-01-01

The process of revising a technical or scientific paper can be performed more efficiently by the people involved (author, co-author, supervisor, editor) when the revision is controlled by breaking it into a series of steps. The revision process recommended here is based on the levels-of-edit concept that resulted from a study of the technical editorial function at the Jet Propulsion Laboratory of the California Institute of Technology. Types of revision discussed are Substantive, Policy, Language, Mechanical Style, Format, Integrity, and Copy Clarification.

75 FR 69649 - Notice of Availability for the Draft Programmatic Environmental Assessment for the Development...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-15

... Draft PEA does not consider other forms of renewable energy. The purpose of the proposed action is to reduce dependency on fossil fuels and increase energy security and efficiency through development of...

Draft Genome Sequences of 12 Dry-Heat-Resistant Bacillus Strains Isolated from the Cleanrooms Where the Viking Spacecraft Were Assembled.

PubMed

Seuylemezian, Arman; Cooper, Kerry; Schubert, Wayne; Vaishampayan, Parag

2018-03-22

Spore-forming microorganisms are of concern for forward contamination because they can survive harsh interplanetary travel. Here, we report the draft genome sequences of 12 spore-forming strains isolated from the Manned Spacecraft Operations Building (MSOB) and the Vehicle Assembly Building (VAB) in Cape Canaveral, FL, where the Viking spacecraft were assembled. Copyright © 2018 Seuylemezian et al.

Analytical drafting curves provide exact equations for plotted data

NASA Technical Reports Server (NTRS)

Stewart, R. B.

1967-01-01

Analytical drafting curves provide explicit mathematical expressions for any numerical data that appears in the form of graphical plots. The curves each have a reference coordinate axis system indicated on the curve as well as the mathematical equation from which the curve was generated.

77 FR 3545 - Notice of Availability of the Draft Program Environmental Impact Report (PEIR): Southern...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-24

... transportation and urban form strategies that encourage compact growth, increased jobs/housing balance and... DEPARTMENT OF TRANSPORTATION Federal Highway Administration Notice of Availability of the Draft... California Environmental Quality Act for the 2012-2035 Regional Transportation Plan and Sustainable...

Collaboration between Writers and Graphic Designers in Documentation Projects.

ERIC Educational Resources Information Center

Mirel, Barbara; And Others

1995-01-01

Analyzes collaborations between software manual writers and graphic designers to discover how their processes of collaboration directly affect the form of a finished manual. Identifies three models of collaboration: assembly line (linear drafting), swap meet (iterative drafting and joint problem solving), and symphony (codevelopment in every…

Lead us not into tanktation: a simulation modelling approach to gain insights into incentives for sporting teams to tank.

PubMed

Tuck, Geoffrey N; Whitten, Athol R

2013-01-01

Annual draft systems are the principal method used by teams in major sporting leagues to recruit amateur players. These draft systems frequently take one of three forms: a lottery style draft, a weighted draft, or a reverse-order draft. Reverse-order drafts can create incentives for teams to deliberately under-perform, or tank, due to the perceived gain from obtaining quality players at higher draft picks. This paper uses a dynamic simulation model that captures the key components of a win-maximising sporting league, including the amateur player draft, draft choice error, player productivity, and between-team competition, to explore how competitive balance and incentives to under-perform vary according to league characteristics. We find reverse-order drafts can lead to some teams cycling between success and failure and to other teams being stuck in mid-ranking positions for extended periods of time. We also find that an incentive for teams to tank exists, but that this incentive decreases (i) as uncertainty in the ability to determine quality players in the draft increases, (ii) as the number of teams in the league reduces, (iii) as team size decreases, and (iv) as the number of teams adopting a tanking strategy increases. Simulation models can be used to explore complex stochastic dynamic systems such as sports leagues, where managers face difficult decisions regarding the structure of their league and the desire to maintain competitive balance.

Lead Us Not into Tanktation: A Simulation Modelling Approach to Gain Insights into Incentives for Sporting Teams to Tank

PubMed Central

Tuck, Geoffrey N.; Whitten, Athol R.

2013-01-01

Annual draft systems are the principal method used by teams in major sporting leagues to recruit amateur players. These draft systems frequently take one of three forms: a lottery style draft, a weighted draft, or a reverse-order draft. Reverse-order drafts can create incentives for teams to deliberately under-perform, or tank, due to the perceived gain from obtaining quality players at higher draft picks. This paper uses a dynamic simulation model that captures the key components of a win-maximising sporting league, including the amateur player draft, draft choice error, player productivity, and between-team competition, to explore how competitive balance and incentives to under-perform vary according to league characteristics. We find reverse-order drafts can lead to some teams cycling between success and failure and to other teams being stuck in mid-ranking positions for extended periods of time. We also find that an incentive for teams to tank exists, but that this incentive decreases (i) as uncertainty in the ability to determine quality players in the draft increases, (ii) as the number of teams in the league reduces, (iii) as team size decreases, and (iv) as the number of teams adopting a tanking strategy increases. Simulation models can be used to explore complex stochastic dynamic systems such as sports leagues, where managers face difficult decisions regarding the structure of their league and the desire to maintain competitive balance. PMID:24312243

75 FR 44790 - Second Draft Document Related to the Review of the National Ambient Air Quality Standards for...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-29

... characters, any form of encryption, and be free of any defects or viruses. Docket: All documents in the... EPA's TTN website at: http://www.epa.gov/ttn/naaqs/standards/pm/s_pm_2007_pa.html . The draft document...

78 FR 43225 - Utah Resource Advisory Council Meeting/Conference Call

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-19

... Utah RAC formed a subgroup to review BLM-Utah's draft three-year National Conservation Lands Strategy... draft strategy and this meeting will be held to discuss the changes. A public comment period will take place immediately following the presentation. The meeting is open to the public; however, transportation...

Regulatory Forum Opinion Piece: Review of FDA Draft Guidance Testicular Toxicity-Evaluation during Drug Development Guidance for Industry.

PubMed

Hukkanen, Renee R; Halpern, Wendy G; Vidal, Justin D

2016-10-01

In July 2015, the U.S. Food and Drug Administration (FDA) posted a new draft guidance entitled "Testicular Toxicity: Evaluation during Drug Development Guidance for Industry," with a 90-day public comment period. As the nonclinical assessment of testicular toxicity often relies on the expert interpretation of pathology affecting the male reproductive tract, this draft guidance is considered directly relevant to the toxicologic pathology community. Therefore, a working group was formed through the Scientific and Regulatory Policy Committee of the Society of Toxicologic Pathologists (STPs) to provide a detailed review of the draft guidance. Specific comments on the guidance were submitted to the FDA by the STP. The draft guidance and all comments received are currently under review with the FDA. This commentary provides a summary of the components of the draft guidance and the comments submitted by the STP with acknowledgment of different perspectives reflected in comments from other respondents. © The Author(s) 2016.

Spheres settling in an Oldroyd-B fluid

NASA Astrophysics Data System (ADS)

Pan, Tsorng-Whay; Glowinski, Roland

2017-11-01

In this talk we present a numerical study of the dynamics of balls settling in a vertical channel with a square cross-section filled with an Oldroyd-B fluid. For the case of two balls, two typical kinds of particle dynamics are obtained: (i) periodic interaction between two balls and (ii) the formation of a vertical chain of two balls. For the periodic interaction of two balls occurred at lower values of the elasticity number, two balls draft, kiss and break away periodically and the chain is not formed due to not strong enough elastic force. For slightly higher values of the elasticity number, two balls draft, kiss and break away a couple times first and then form a chain. Such chain finally becomes a vertical one after the oscillation damps out. For higher values of the elasticity number, two balls draft, kiss and form a vertical chain right away. The formation of three ball chain can be obtained at higher values of the elasticity number. This work was supported by NSF (Grant DMS-1418308).

Draft Genome Sequence of Bacillus coagulans GBI-30, 6086, a Widely Used Spore-Forming Probiotic Strain

PubMed Central

Orrù, Luigi; Salvetti, Elisa; Cattivelli, Luigi; Lamontanara, Antonella; Michelotti, Vania; Capozzi, Vittorio; Spano, Giuseppe; Keller, David; Cash, Howard; Martina, Alessia; Felis, Giovanna E.

2014-01-01

Bacillus coagulans GBI-30, 6086 is a safe strain, already available on the market, and characterized by certified beneficial effects. The draft genome sequence presented here constitutes the first pillar toward the identification of the molecular mechanisms responsible for its positive features and safety. PMID:25377698

Draft Genome sequence of Frankia sp. Strain QA3, a nitrogen-fixing actinobacterium isolated from the root nodule of Alnus nitida

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sen, Arnab; Beauchemin, Nicholas; Bruce, David

Members of actinomycete genus Frankia form a nitrogen-fixing symbiosis with 8 different families of actinorhizal plants. We report a high-quality draft genome sequence for Frankia sp. stain QA3, a nitrogen-fixing actinobacterium isolated from root nodules of Alnus nitida.

The dynamics of genetic draft in rapidly adapting populations.

PubMed

Kosheleva, Katya; Desai, Michael M

2013-11-01

The accumulation of beneficial mutations on competing genetic backgrounds in rapidly adapting populations has a striking impact on evolutionary dynamics. This effect, known as clonal interference, causes erratic fluctuations in the frequencies of observed mutations, randomizes the fixation times of successful mutations, and leaves distinct signatures on patterns of genetic variation. Here, we show how this form of "genetic draft" affects the forward-time dynamics of site frequencies in rapidly adapting asexual populations. We calculate the probability that mutations at individual sites shift in frequency over a characteristic timescale, extending Gillespie's original model of draft to the case where many strongly selected beneficial mutations segregate simultaneously. We then derive the sojourn time of mutant alleles, the expected fixation time of successful mutants, and the site frequency spectrum of beneficial and neutral mutations. Finally, we show how this form of draft affects inferences in the McDonald-Kreitman test and how it relates to recent observations that some aspects of genetic diversity are described by the Bolthausen-Sznitman coalescent in the limit of very rapid adaptation.

Tax-exempt hospitals and community benefits: a review of state reporting requirements.

PubMed

Hellinger, Fred Joseph

2009-02-01

In June 2007 the Internal Revenue Service proposed a major overhaul of its reporting requirements for tax-exempt hospitals and released draft Form 990 (the IRS form filed by tax-exempt organizations each year). In December 2007 the IRS promulgated the final Form 990 after incorporating some of the recommendations made in the almost seven hundred public comments on the discussion draft. One recommendation adopted in the final Form 990 is the postponement until tax year 2009 (returns filed in 2010) of the requirement for hospitals to submit detailed information on the percentage of total expenses attributable to charity care, unreimbursed Medicaid costs, and community-health improvement programs (the discussion draft required this information for tax year 2007). Although the IRS will not require tax-exempt hospitals to provide detailed information about community benefits until the 2009 tax year, sixteen states have laws requiring tax-exempt hospitals to enumerate the benefits that they provide to the community. Information about the impact of these laws on the provision of community benefits (e.g., charity and uncompensated care) is examined in this study whose primary purpose is to highlight information policy makers may glean from states that have adopted community-benefit reporting laws.

Crafting effective tobacco counteradvertisements: lessons from a failed campaign directed at teenagers.

PubMed Central

McKenna, J W; Williams, K N

1993-01-01

Focus group research conducted by the Centers for Disease Control and Prevention's Office on Smoking and Health suggested that the desire of teenagers to gain control over their lives would make them responsive to a counteradvertising strategy aimed at exposing the predatory marketing techniques of the tobacco industry. On the basis of this strategy, the office developed draft print advertisements and a rough TV commercial featuring such theme lines as "You get an image. They get an addict." In those ads, "they" referred to cigarette companies. Subsequent testing of the campaign materials, however, indicated that the subtle, sophisticated execution of this concept of manipulation by the industry did not communicate clearly and effectively to an audience of young teens. In fact, 38 percent of those who viewed the rough TV spot believed that the main message promoted smoking. These negative test findings underscore the critical need for ongoing audience research throughout the creative process to ensure that campaign planners stay "in tune" with their consumers. PMID:8210278

Secondary School Curriculum Guide. Music, Grades 7-9. Draft Copy.

ERIC Educational Resources Information Center

Rogers, Arnold R., Ed.; And Others

This draft curriculum guide is for use in grades 7-9 and covers six levels of musical competence. The levels included for study in this 3 year program are: 1) general music, in which the student learns about rythm, tempo, and beat patterns, note and rest values, time signatures, and some musical terms; 2) musical forms, elements of music, score…

The National Football League (NFL) combine: does normalized data better predict performance in the NFL draft?

PubMed

Robbins, Daniel W

2010-11-01

The objective of this study was to investigate the predictive ability of National Football League (NFL) combine physical test data to predict draft order over the years 2005-2009. The NFL combine provides a setting in which NFL personnel can evaluate top draft prospects. The predictive ability of combine data in its raw form and when normalized in both a ratio and allometric manner was examined for 17 positions. Data from 8 combine physical performance tests were correlated with draft order to determine the direction and strength of relationship between the various combine measures and draft order. Players invited to the combine and subsequently drafted in the same year (n = 1,155) were included in the study. The primary finding was that performance in the combine physical test battery, whether normalized or not, has little association with draft success. In terms of predicting draft order from outcomes of the 8 tests making up the combine battery, normalized data provided no advantage over raw data. Of the 8 performance measures investigated, straight sprint time and jumping ability seem to hold the most weight with NFL personnel responsible for draft decisions. The NFL should consider revising the combine test battery to reflect the physical characteristics it deems important. It may be that NFL teams are more interested in attributes other than the purely physical traits reflected in the combine test battery. Players with aspirations of entering the NFL may be well advised to develop mental and technical skills in addition to developing the physical characteristics necessary to optimize performance.

72. photographer unknown 22 November 1935 PLACING CONCRETE FORM FOR ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

72. photographer unknown 22 November 1935 PLACING CONCRETE FORM FOR STATION SERVICE DRAFT TUBES. - Bonneville Project, Powerhouse No.1, Spanning Bradford Slough, from Bradford Island, Bonneville, Multnomah County, OR

Draft Genome Sequence of an Anaerobic and Extremophilic Bacterium, Caldanaerobacter yonseiensis, Isolated from a Geothermal Hot Stream

PubMed Central

Lee, Sang-Jae; Lee, Yong-Jik; Park, Gun-Seok; Kim, Byoung-Chan; Lee, Sang Jun; Shin, Jae-Ho

2013-01-01

Caldanaerobacter yonseiensis is a strictly anaerobic, thermophilic, spore-forming bacterium, which was isolated from a geothermal hot stream in Indonesia. This bacterium utilizes xylose and produces a variety of proteases. Here, we report the draft genome sequence of C. yonseiensis, which reveals insights into the pentose phosphate pathway and protein degradation metabolism in thermophilic microorganisms. PMID:24201201

Fall Department Head Report--Reporting Booklet 2.0 to the Massachusetts Division of Occupational Education (Fiscal Year Ending June 30, 1975) for Drafting.

ERIC Educational Resources Information Center

Management and Information System for Occupational Education, Winchester, MA.

The reporting booklet is required for the Census Data System (CDS) of the Management Information System for Occupational Education (MISOE); it contains the reporting forms which collect data that describe program structure and job-entry skill outcomes expected of program completors in the individual occupational education area of drafting.…

Draft Genome Sequence of the Sulfate-Reducing Bacterium Desulfotomaculum copahuensis Strain CINDEFI1 Isolated from the Geothermal Copahue System, Neuquén, Argentina

PubMed Central

Yaakop, Amira Suriaty; Chan, Chia Sing; Urbieta, M. Sofía; Ee, Robson; Tan-Guan-Sheng, Adrian; Donati, Edgardo R.

2016-01-01

Desulfotomaculum copahuensis strain CINDEFI1 is a novel spore-forming sulfate-reducing bacterium isolated from the Copahue volcano area, Argentina. Here, we present its draft genome in which we found genes related with the anaerobic respiration of sulfur compounds similar to those present in the Copahue environment. PMID:27540078

62. photographer unknown undated ERECTING FORMS, PLACING REINFORCING STEEL, AND ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

62. photographer unknown undated ERECTING FORMS, PLACING REINFORCING STEEL, AND CONCRETING DRAFT PIER OF POWERHOUSE. - Bonneville Project, Powerhouse No.1, Spanning Bradford Slough, from Bradford Island, Bonneville, Multnomah County, OR

Combined thickness of the uterus and placenta and ultrasonographic examinations of uteroplacental tissues in normal pregnancy, placentitis, and abnormal parturitions in heavy draft horses.

PubMed

Kimura, Yuki; Haneda, Shingo; Aoki, Takahiro; Furuoka, Hidefumi; Miki, Wataru; Fukumoto, Natsuko; Matsui, Motozumi; Nambo, Yasuo

2018-01-01

The combined thickness of the uterus and placenta (CTUP) and ultrasonographic images of uteroplacental tissues were investigated in 35 pregnant heavy draft horses in Months 7-12 of pregnancy. The mares were divided into three groups: those pathologically diagnosed as placentitis (placentitis group, n=3); those who had abortion, premature birth, or fetal malformation (abnormal group, n=7); and those who had no abnormal findings (normal group, n=25). In the normal group, CTUP increased as pregnancy progressed from Months 7 (median, 7.08 mm; range, 5.68-11.27) to 12 (13.31 mm; 7.44-16.31 mm) (P<0.05) and was higher than those reported previously in Thoroughbred, quarter, and American paint horses. Values of CTUP greater than the 75th percentile of the normal group from Months 7 (7.54 mm) to 12 (15.19 mm) were detected in 100% of the placentitis group (3/3) and in 86% of the abnormal group (6/7). Ultrasonographic images showing placental separation were obtained in 67% of the placentitis group (2/3), 29% of the abnormal group (2/7), and 20% of the normal group (5/25). Pathological placental edema and ultrasonographic images showing uteroplacental roughness or distinguishability were observed even in the normal group. These findings suggest that increased CTUP and placental separation would reflect placentitis and abnormal pregnancies and may help to detect them in heavy draft horses.

Challenge To Apollo: The Soviet Union and The Space Race, 1945-1974

NASA Technical Reports Server (NTRS)

Siddiqi, Asif A.

2000-01-01

This book is, in essence, sixteen years in the making. First attempted to compile a history of the Soviet space program in 1982 author put together a rough chronology of the main events. A decade later, while living on a couch in a college friend's apartment, he began writing what would be a short history of the Soviet lunar landing program. The first draft was sixty-nine pages long. Late the following year, he decided to expand the topic to handle all early Soviet piloted exploration programs. That work eventually grew into what you are holding in your hand now.

Draft Genome Sequence of Brevibacillus laterosporus OSY-I1, a Strain That Produces Brevibacillin, Which Combats Drug-Resistant Gram-Positive Bacteria

PubMed Central

Yang, Xu; Yesil, Mustafa; Xiaoli, Lingzi; Dudley, Edward G.

2017-01-01

ABSTRACT Brevibacillus laterosporus OSY-I1 is a Gram-positive spore-forming bacterium isolated from soil. The bacterium produces brevibacillin, an antimicrobial lipopeptide effective against several drug-resistant Gram-positive bacteria. Here, we present the draft genome sequence of the strain OSY-I1 and the gene cluster responsible for the biosynthesis of brevibacillin. PMID:29025947

Draft Genome Sequence of the Sulfate-Reducing Bacterium Desulfotomaculum copahuensis Strain CINDEFI1 Isolated from the Geothermal Copahue System, Neuquén, Argentina.

PubMed

Willis Poratti, Graciana; Yaakop, Amira Suriaty; Chan, Chia Sing; Urbieta, M Sofía; Chan, Kok-Gan; Ee, Robson; Tan-Guan-Sheng, Adrian; Goh, Kian Mau; Donati, Edgardo R

2016-08-18

Desulfotomaculum copahuensis strain CINDEFI1 is a novel spore-forming sulfate-reducing bacterium isolated from the Copahue volcano area, Argentina. Here, we present its draft genome in which we found genes related with the anaerobic respiration of sulfur compounds similar to those present in the Copahue environment. Copyright © 2016 Willis Poratti et al.

18 CFR 35.13 - Filing of changes in rate schedules, tariffs or service agreements.

Code of Federal Regulations, 2014 CFR

2014-04-01

... be reconciled with the utility's most recent FERC Form 1. If the utility has not yet submitted Form 1 for the Test Period, the utility shall submit the relevant Form 1 pages in draft form. (D) The utility.... Balance sheets shall be constructed in accordance with the annual report form for electric utilities...

18 CFR 35.13 - Filing of changes in rate schedules, tariffs or service agreements.

Code of Federal Regulations, 2013 CFR

2013-04-01

... be reconciled with the utility's most recent FERC Form 1. If the utility has not yet submitted Form 1 for the Test Period, the utility shall submit the relevant Form 1 pages in draft form. (D) The utility.... Balance sheets shall be constructed in accordance with the annual report form for electric utilities...

18 CFR 35.13 - Filing of changes in rate schedules, tariffs or service agreements.

Code of Federal Regulations, 2010 CFR

2010-04-01

... be reconciled with the utility's most recent FERC Form 1. If the utility has not yet submitted Form 1 for the Test Period, the utility shall submit the relevant Form 1 pages in draft form. (D) The utility.... Balance sheets shall be constructed in accordance with the annual report form for electric utilities...

18 CFR 35.13 - Filing of changes in rate schedules, tariffs or service agreements.

Code of Federal Regulations, 2011 CFR

2011-04-01

... be reconciled with the utility's most recent FERC Form 1. If the utility has not yet submitted Form 1 for the Test Period, the utility shall submit the relevant Form 1 pages in draft form. (D) The utility.... Balance sheets shall be constructed in accordance with the annual report form for electric utilities...

18 CFR 35.13 - Filing of changes in rate schedules, tariffs or service agreements.

Code of Federal Regulations, 2012 CFR

2012-04-01

... be reconciled with the utility's most recent FERC Form 1. If the utility has not yet submitted Form 1 for the Test Period, the utility shall submit the relevant Form 1 pages in draft form. (D) The utility.... Balance sheets shall be constructed in accordance with the annual report form for electric utilities...

15 CFR 762.3 - Records exempt from recordkeeping requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

...; (2) Special export file list; (3) Vessel log from freight forwarder; (4) Inspection certificate; (5... form; (12) Financial hold form; (13) Export parts shipping problem form; (14) Draft number log; (15) Expense invoice mailing log; (16) Financial status report; (17) Bank release of guarantees; (18) Cash...

15 CFR 762.3 - Records exempt from recordkeeping requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

...; (2) Special export file list; (3) Vessel log from freight forwarder; (4) Inspection certificate; (5... form; (12) Financial hold form; (13) Export parts shipping problem form; (14) Draft number log; (15) Expense invoice mailing log; (16) Financial status report; (17) Bank release of guarantees; (18) Cash...

How supercontinents and superoceans affect seafloor roughness.

PubMed

Whittaker, Joanne M; Müller, R Dietmar; Roest, Walter R; Wessel, Paul; Smith, Walter H F

2008-12-18

Seafloor roughness varies considerably across the world's ocean basins and is fundamental to controlling the circulation and mixing of heat in the ocean and dissipating eddy kinetic energy. Models derived from analyses of active mid-ocean ridges suggest that ocean floor roughness depends on seafloor spreading rates, with rougher basement forming below a half-spreading rate threshold of 30-35 mm yr(-1) (refs 4, 5), as well as on the local interaction of mid-ocean ridges with mantle plumes or cold-spots. Here we present a global analysis of marine gravity-derived roughness, sediment thickness, seafloor isochrons and palaeo-spreading rates of Cretaceous to Cenozoic ridge flanks. Our analysis reveals that, after eliminating effects related to spreading rate and sediment thickness, residual roughness anomalies of 5-20 mGal remain over large swaths of ocean floor. We found that the roughness as a function of palaeo-spreading directions and isochron orientations indicates that most of the observed excess roughness is not related to spreading obliquity, as this effect is restricted to relatively rare occurrences of very high obliquity angles (>45 degrees ). Cretaceous Atlantic ocean floor, formed over mantle previously overlain by the Pangaea supercontinent, displays anomalously low roughness away from mantle plumes and is independent of spreading rates. We attribute this observation to a sub-Pangaean supercontinental mantle temperature anomaly leading to slightly thicker than normal Late Jurassic and Cretaceous Atlantic crust, reduced brittle fracturing and smoother basement relief. In contrast, ocean crust formed above Pacific superswells, probably reflecting metasomatized lithosphere underlain by mantle at only slightly elevated temperatures, is not associated with basement roughness anomalies. These results highlight a fundamental difference in the nature of large-scale mantle upwellings below supercontinents and superoceans, and their impact on oceanic crustal accretion.

Teacher-Board Relations in Connecticut: A Summary of the Law Regarding Scope of Negotiations, Good Faith Bargaining, and Unfair Labor Practices. Preliminary Draft.

ERIC Educational Resources Information Center

Zirkel, Perry A.

This document is a discussion draft intended to lead to the formulation of a set of guidelines by the state board of education concerning three areas of teacher negotiations: scope, good faith bargaining, and prohibited practices. It has been prepared in the form of an organized data base that focuses on summarizing the present state of the law…

Effects of Surface Roughness on Conical Squeeze Film Bearings with Micropolar fluid

NASA Astrophysics Data System (ADS)

Rajani, C. B.; Hanumagowda, B. N.; Shigehalli, Vijayalaxmi S.

2018-04-01

In the current paper, a hypothetical analysis of the impact of surface roughness on squeeze film lubrication of rough conical bearing using Micropolar fluid is examined using Eringen’sMicropolar fluid model. The generalized averaged Reynolds type equation for roughness has been determined analytically using the Christensen’s stochastic theory of roughness effects and the closed form expressions are obtained for the fluid film pressure, load carrying capacity and squeezing time. Further, the impacts of surface roughness using micropolar fluids on the squeeze film lubrication of rough conical bearings has been discussed and according to the outcomes arrived, pressure, load carrying capacity and squeezing time increases for azimuthal roughness pattern and decreases for radial roughness patterns comparatively to the smooth case.

a New Animation of Subduction Processes for Undergraduates

NASA Astrophysics Data System (ADS)

Stern, R. J.; Lieu, W. K.; Mantey, A.; Ward, A.; Todd, F.; Farrar, E.; Sean, M.; Windler, J.

2015-12-01

The subduction of oceanic lithosphere beneath convergent plate margins is a fundamental plate tectonic concept and an important Earth process. It is responsible for some of Earth's most dangerous natural hazards including earthquakes and volcanic eruptions but also produced the continental crust and important mineral deposits. A range of geoscientific efforts including NSF MARGINS and GeoPRISMS initiatives have advanced our understanding of subduction zone processes. In spite the importance of subduction zones and our advancing understanding of how these function, there are few animations that clearly explain the subduction process to non-expert audiences. This deficiency reflects the disparate expertises between geoscientists who know the science but have weak animation skills and digital artists and animators who have strong skills in showing objects in motion but are not experts in natural processes like plate tectonics. This transdisciplinary gap can and should be bridged. With a small grant from NSF (DUE-1444954) we set about to generate a realistic subduction zone animation aimed at the university undergraduate audience by first working within our university to rough out a draft animation and then contract a professional to use this to construct the final version. UTD Geosciences faculty (Stern) and graduate student (Lieu) teamed up with faculty from UTD School of Arts, Technology, and Emerging Communication (ATEC)(Farrar, Fechter, and McComber) to identify and recruit talented ATEC undergraduate students (Mantey, Ward) to work on the project. Geoscientists assembled a storyboard and met weekly with ATEC undergraduates to generate a first draft of the animation, which guided development of an accompanying narrative. The draft animation with voice-over was then handed off to professional animator Windler (Archistration CG) to generate the final animation. We plan to show both the student-generated draft version and the final animation during our presentation. The final animation will be freely available via the internet and will also be used as a supplement for McGraw-Hill textbooks in oceanography, physical geology, Earth science, geography, historical geology, natural hazards, and natural resources.

Machining process influence on the chip form and surface roughness by neuro-fuzzy technique

NASA Astrophysics Data System (ADS)

Anicic, Obrad; Jović, Srđan; Aksić, Danilo; Skulić, Aleksandar; Nedić, Bogdan

2017-04-01

The main aim of the study was to analyze the influence of six machining parameters on the chip shape formation and surface roughness as well during turning of Steel 30CrNiMo8. Three components of cutting forces were used as inputs together with cutting speed, feed rate, and depth of cut. It is crucial for the engineers to use optimal machining parameters to get the best results or to high control of the machining process. Therefore, there is need to find the machining parameters for the optimal procedure of the machining process. Adaptive neuro-fuzzy inference system (ANFIS) was used to estimate the inputs influence on the chip shape formation and surface roughness. According to the results, the cutting force in direction of the depth of cut has the highest influence on the chip form. The testing error for the cutting force in direction of the depth of cut has testing error 0.2562. This cutting force determines the depth of cut. According to the results, the depth of cut has the highest influence on the surface roughness. Also the depth of cut has the highest influence on the surface roughness. The testing error for the cutting force in direction of the depth of cut has testing error 5.2753. Generally the depth of cut and the cutting force which provides the depth of cut are the most dominant factors for chip forms and surface roughness. Any small changes in depth of cut or in cutting force which provide the depth of cut could drastically affect the chip form or surface roughness of the working material.

Refining scientific writing skills with feedback that works for students and instructors

NASA Astrophysics Data System (ADS)

Kiani, Leily S.; Menke, Carrie

2015-10-01

Evaluation of student learning through assessment of communication skills is a generally important component of undergraduate education and particularly so for promotion of interdisciplinary research conducted by future scientists. To better build these skills we aim to quantify the effectiveness of feedback on student writing of technical reports in an upper-division physics lab course. In one implementation, feedback utilization - in the form of observing commented technical reports, attending office hours or emailing rough drafts of their reports was monitored then correlated with improvement in student writing. The improvement in student writing is quantified as the single-student normalized gain. A slight positive relationship was found between the number of times a student utilized feedback and the improvement in student writing. A subsequent study involved correlation of two complimentary assessments of student work. In the first assessment students received consistent feedback throughout the semester on all sections of a technical report in the form of highlighted bullet points in a detailed rubric. In the second assessment method students received varying amounts of feedback for each section of the technical paper throughout the semester with a focus on one section each week and follow-up feedback on previously covered sections. This approach provides focused feedback that can be scalable to larger classes. The number of highlighted bullet points in the rubric clearly decreases as a function of the focused feedback implementation. From this we conclude that student writing improves with the focused feedback method.

Process Parameters Optimization in Single Point Incremental Forming

NASA Astrophysics Data System (ADS)

Gulati, Vishal; Aryal, Ashmin; Katyal, Puneet; Goswami, Amitesh

2016-04-01

This work aims to optimize the formability and surface roughness of parts formed by the single-point incremental forming process for an Aluminium-6063 alloy. The tests are based on Taguchi's L18 orthogonal array selected on the basis of DOF. The tests have been carried out on vertical machining center (DMC70V); using CAD/CAM software (SolidWorks V5/MasterCAM). Two levels of tool radius, three levels of sheet thickness, step size, tool rotational speed, feed rate and lubrication have been considered as the input process parameters. Wall angle and surface roughness have been considered process responses. The influential process parameters for the formability and surface roughness have been identified with the help of statistical tool (response table, main effect plot and ANOVA). The parameter that has the utmost influence on formability and surface roughness is lubrication. In the case of formability, lubrication followed by the tool rotational speed, feed rate, sheet thickness, step size and tool radius have the influence in descending order. Whereas in surface roughness, lubrication followed by feed rate, step size, tool radius, sheet thickness and tool rotational speed have the influence in descending order. The predicted optimal values for the wall angle and surface roughness are found to be 88.29° and 1.03225 µm. The confirmation experiments were conducted thrice and the value of wall angle and surface roughness were found to be 85.76° and 1.15 µm respectively.

Career Profiles- Drawing Controller Kelvin Siu- Operations Engineering Branch

NASA Image and Video Library

2016-06-23

The Drawing Control group provides project support in the form of drafting services, drawing version management, and drawing archival. The office provides drafting services through creation of new drawings and sketches, or integration of red-lines. They maintain physical and electronic storage of flight vehicle drawings, and archive all sketches for the AFRC community. This office is the controlling organization for all Armstrong drawing formats and maintains the drawing numbering system for flight vehicle projects.

High-quality permanent draft genome sequence of Bradyrhizobium sp. Th.b2, a microsymbiont of Amphicarpaea bracteata collected in Johnson City, New York

DOE PAGES

Tian, Rui; Parker, Matthew; Seshadri, Rekha; ...

2015-05-16

Bradyrhizobium sp. Th.b2 is an aerobic, motile, Gram-negative, non-spore-forming rod that was isolated from an effective nitrogen-fixing root nodule of Amphicarpaea bracteata collected in Johnson City, New York. Here we describe the features of Bradyrhizobium sp. Th.b2, together with high-quality permanent draft genome sequence information and annotation. The 10,118,060 high-quality draft genome is arranged in 266 scaffolds of 274 contigs, contains 9,809 protein-coding genes and 108 RNA-only encoding genes. In conclusion, this rhizobial genome was sequenced as part of the DOE Joint Genome Institute 2010 Genomic Encyclopedia for Bacteria and Archaea-Root Nodule Bacteria (GEBA-RNB) project.

High-quality permanent draft genome sequence of Bradyrhizobium sp. Th.b2, a microsymbiont of Amphicarpaea bracteata collected in Johnson City, New York

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tian, Rui; Parker, Matthew; Seshadri, Rekha

Bradyrhizobium sp. Th.b2 is an aerobic, motile, Gram-negative, non-spore-forming rod that was isolated from an effective nitrogen-fixing root nodule of Amphicarpaea bracteata collected in Johnson City, New York. Here we describe the features of Bradyrhizobium sp. Th.b2, together with high-quality permanent draft genome sequence information and annotation. The 10,118,060 high-quality draft genome is arranged in 266 scaffolds of 274 contigs, contains 9,809 protein-coding genes and 108 RNA-only encoding genes. In conclusion, this rhizobial genome was sequenced as part of the DOE Joint Genome Institute 2010 Genomic Encyclopedia for Bacteria and Archaea-Root Nodule Bacteria (GEBA-RNB) project.

Studies of SERS efficiency of gold coated porous silicon formed on rough silicon backside

NASA Astrophysics Data System (ADS)

Dridi, H.; Haji, L.; Moadhen, A.

2017-12-01

Starting from a rough backside of silicon wafer, we have formed a porous layer by electrochemical anodization and then coated by a thin film of gold. The morphological characteristics of the porous silicon and in turn the metal film are governed by the anodization process and also by the starting surface. So, in order to investigate the Plasmonic aspect of such rough surface which combines roughness inherent to the porous nature and that due to rough starting surface, we have used a dye target molecule to study its SERS signal using a porous silicon layer obtained on the rough backside surface. The use of unusual backside of silicon wafer could be, beside the others, an interesting way to made SERS effective substrate thanks to reproducible rough porous gold on porous layer from this starting face. The morphological results correspond to the silicon rough surface as a function of the crystallographic orientation showed the presence of two different substrate structure. The optical reflectivity results obtained of gold deposited on oxidized porous silicon showed a dependence of its Localized Surface Plasmon band frequency of the deposit time. SERS results, obtained for a dye target molecule (Rhodamine 6G), show a higher intensities in the case of the 〈110〉 orientation, which characterized by the higher roughness surface. Voici "the most relevant and important aspects of our work".

Form drag in rivers due to small-scale natural topographic features: 1. Regular sequences

USGS Publications Warehouse

Kean, J.W.; Smith, J.D.

2006-01-01

Small-scale topographic features are commonly found on the boundaries of natural rivers, streams, and floodplains. A simple method for determining the form drag on these features is presented, and the results of this model are compared to laboratory measurements. The roughness elements are modeled as Gaussian-shaped features defined in terms of three parameters: a protrusion height, H; a streamwise length scale, ??; and a spacing between crests, ??. This shape is shown to be a good approximation to a wide variety of natural topographic bank features. The form drag on an individual roughness element embedded in a series of identical elements is determined using the drag coefficient of the individual element and a reference velocity that includes the effects of roughness elements further upstream. In addition to calculating the drag on each element, the model determines the spatially averaged total stress, skin friction stress, and roughness height of the boundary. The effects of bank roughness on patterns of velocity and boundary shear stress are determined by combining the form drag model with a channel flow model. The combined model shows that drag on small-scale topographic features substantially alters the near-bank flow field. These methods can be used to improve predictions of flow resistance in rivers and to form the basis for fully predictive (no empirically adjusted parameters) channel flow models. They also provide a foundation for calculating the near-bank boundary shear stress fields necessary for determining rates of sediment transport and lateral erosion.

Flight Research: Problems Encountered and What They Should Teach Us

NASA Technical Reports Server (NTRS)

Thompson, Milton O.; Hunley, J. D.; Launius, Roger (Technical Monitor)

2000-01-01

The document by Milt Thompson that is reproduced here was an untitled rough draft found in Thompson's papers in the Dryden Historical Reference Collection. Internal evidence suggests that it was written around 1974. I have not attempted to second guess what Milt might have done in revising the paper, but I have made some minor stylistic changes to make it more readable without changing the sense of what Milt initially wrote. For the most part, I have not attempted to bring his comments up to date. For readers who may not be familiar with the history of what is today the NASA Dryden Flight Research Center and of its predecessor organizations, I have added a background section.

On Fuzzy Sets and Rough Sets from the Perspective of Indiscernibility

NASA Astrophysics Data System (ADS)

Chakraborty, Mihir K.

The category theoretic approach of Obtułowicz to Pawlak's rough sets has been reintroduced in a somewhat modified form. A generalization is rendered to this approach that has been motivated by the notion of rough membership function. Thus, a link is established between rough sets and L-fuzzy sets for some special lattices. It is shown that a notion of indistinguishability lies at the root of vagueness. This observation in turn gives a common ground to the theories of rough sets and fuzzy sets.

Molecular dynamics simulation of nanobubble nucleation on rough surfaces

NASA Astrophysics Data System (ADS)

Liu, Yawei; Zhang, Xianren

2017-04-01

Here, we study how nanobubbles nucleate on rough hydrophobic surfaces, using long-time standard simulations to directly observe the kinetic pathways and using constrained simulations combined with the thermodynamic integration approach to quantitatively evaluate the corresponding free energy changes. Both methods demonstrate that a two-step nucleation route involving the formation of an intermediate state is thermodynamically favorable: at first, the system transforms from the Wenzel state (liquid being in full contact with the solid surface) to the Cassie state (liquid being in contact with the peaks of the rough surface) after gas cavities occur in the grooves (i.e., the Wenzel-to-Cassie transition); then, the gas cavities coalesce and form a stable surface nanobubble with pinned contact lines (i.e., the Cassie-to-nanobubble transition). Additionally, the free energy barriers for the two transitions show opposing dependencies on the degree of surface roughness, indicating that the surfaces with moderate roughness are favorable for forming stable surface nanobubbles. Moreover, the simulation results also reveal the coexistence and transition between the Wenzel, Cassie, and nanobubble states on rough surfaces.

Draft Whole-Genome Sequences of Escherichia fergusonii Strains Isolated from Beef Trim (GTA-EF02), Ground Beef (GTA-EF03), and Chopped Kale (GTA-EF04).

PubMed

Manninger, Paul; Koziol, Adam; Carrillo, Catherine D

2016-04-14

Escherichia fergusoniiis a Gram-negative, rod-shaped, non-spore-forming member of theEnterobacteriaceaefamily and is a bacterium with both biotechnological applications and implication in human clinical disease. Here, we report the draft genome sequences of three isolates ofE. fergusoniifrom beef trim (GTA-EF02), ground beef (GTA-EF03), and chopped kale (GTA-EF04). Copyright © 2016 Manninger et al.

High-quality permanent draft genome sequence of Bradyrhizobium sp. Tv2a.2, a microsymbiont of Tachigali versicolor discovered in Barro Colorado Island of Panama

DOE PAGES

Tian, Rui; Parker, Matthew; Seshadri, Rekha; ...

2015-05-17

Bradyrhizobiumsp. Tv2a.2 is an aerobic, motile, Gram-negative, non-spore-forming rod that was isolated from an effective nitrogen-fixing root nodule of Tachigali versicolor collected in Barro Colorado Island of Panama. Here we describe the features of Bradyrhizobiumsp. Tv2a.2, together with high-quality permanent draft genome sequence information and annotation. The 8,496,279 bp high-quality draft genome is arranged in 87 scaffolds of 87 contigs, contains 8,109 protein-coding genes and 72 RNA-only encoding genes. In conclusion, this rhizobial genome was sequenced as part of the DOE Joint Genome Institute 2010 Genomic Encyclopedia for Bacteria and Archaea-Root Nodule Bacteria (GEBA-RNB) project.

Electronic Submissions of Pesticide Applications

EPA Pesticide Factsheets

Applications for pesticide registration can be submitted electronically, including forms, studies, and draft product labeling. Applicants need not submit multiple electronic copies of any pieces of their applications.

Mars Sample Handling Protocol Workshop Series: Workshop 4

NASA Technical Reports Server (NTRS)

Race Margaret S. (Editor); DeVincenzi, Donald L. (Editor); Rummel, John D. (Editor); Acevedo, Sara E. (Editor)

2001-01-01

In preparation for missions to Mars that will involve the return of samples to Earth, it will be necessary to prepare for the receiving, handling, testing, distributing, and archiving of martian materials here on Earth. Previous groups and committees have studied selected aspects of sample return activities, but specific detailed protocols for the handling and testing of returned samples must still be developed. To further refine the requirements for sample hazard testing and to develop the criteria for subsequent release of sample materials from quarantine, the NASA Planetary Protection Officer convened a series of workshops in 2000-2001. The overall objective of the Workshop Series was to produce a Draft Protocol by which returned martian sample materials can be assessed for biological hazards and examined for evidence of life (extant or extinct) while safeguarding the purity of the samples from possible terrestrial contamination. This report also provides a record of the proceedings of Workshop 4, the final Workshop of the Series, which was held in Arlington, Virginia, June 5-7, 2001. During Workshop 4, the sub-groups were provided with a draft of the protocol compiled in May 2001 from the work done at prior Workshops in the Series. Then eight sub-groups were formed to discuss the following assigned topics: Review and Assess the Draft Protocol for Physical/Chemical Testing Review and Assess the Draft Protocol for Life Detection Testing Review and Assess the Draft Protocol for Biohazard Testing Environmental and Health/Monitoring and Safety Issues Requirements of the Draft Protocol for Facilities and Equipment Contingency Planning for Different Outcomes of the Draft Protocol Personnel Management Considerations in Implementation of the Draft Protocol Draft Protocol Implementation Process and Update Concepts This report provides the first complete presentation of the Draft Protocol for Mars Sample Handling to meet planetary protection needs. This Draft Protocol, which was compiled from deliberations and recommendations from earlier Workshops in the Series, represents a consensus that emerged from the discussions of all the sub-groups assembled over the course of the five Workshops of the Series. These discussions converged on a conceptual approach to sample handling, as well as on specific analytical requirements. Discussions also identified important issues requiring attention, as well as research and development needed for protocol implementation.

Figure correction of a metallic ellipsoidal neutron focusing mirror

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guo, Jiang, E-mail: jiang.guo@riken.jp; Yamagata, Yutaka; Morita, Shin-ya

2015-06-15

An increasing number of neutron focusing mirrors is being adopted in neutron scattering experiments in order to provide high fluxes at sample positions, reduce measurement time, and/or increase statistical reliability. To realize a small focusing spot and high beam intensity, mirrors with both high form accuracy and low surface roughness are required. To achieve this, we propose a new figure correction technique to fabricate a two-dimensional neutron focusing mirror made with electroless nickel-phosphorus (NiP) by effectively combining ultraprecision shaper cutting and fine polishing. An arc envelope shaper cutting method is introduced to generate high form accuracy, while a fine polishingmore » method, in which the material is removed effectively without losing profile accuracy, is developed to reduce the surface roughness of the mirror. High form accuracy in the minor-axis and the major-axis is obtained through tool profile error compensation and corrective polishing, respectively, and low surface roughness is acquired under a low polishing load. As a result, an ellipsoidal neutron focusing mirror is successfully fabricated with high form accuracy of 0.5 μm peak-to-valley and low surface roughness of 0.2 nm root-mean-square.« less

A PARADOXICAL RELATION BETWEEN ZETA POTENTIAL AND SUSPENSION STABILITY IN S AND R VARIANTS OF INTESTINAL BACTERIA

PubMed Central

Joffe, Eleanore W.; Mudd, Stuart

1935-01-01

The relation between electrokinetic potential and suspension stability of four strains of non-flagellate intestinal bacteria has been studied. The smooth forms have ζ-potentials which approximate zero over a wide range of pH and salt concentration, yet nevertheless form stable suspensions. The rough variants have ζ-potentials which vary with pH and electrolyte concentration in the familiar way. The rough forms have values of ζ-potential critical for their suspension stability. PMID:19872869

Analysis of Cloud-resolving Simulations of a Tropical Mesoscale Convective System Observed during TWP-ICE: Vertical Fluxes and Draft Properties in Convective and Stratiform Regions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mrowiec, Agnieszka A.; Rio, Catherine; Fridlind, Ann

2012-10-02

We analyze three cloud-resolving model simulations of a strong convective event observed during the TWP-ICE campaign, differing in dynamical core, microphysical scheme or both. Based on simulated and observed radar reflectivity, simulations roughly reproduce observed convective and stratiform precipitating areas. To identify the characteristics of convective and stratiform drafts that are difficult to observe but relevant to climate model parameterization, independent vertical wind speed thresholds are calculated to capture 90% of total convective and stratiform updraft and downdraft mass fluxes. Convective updrafts are fairly consistent across simulations (likely owing to fixed large-scale forcings and surface conditions), except that hydrometeor loadingsmore » differ substantially. Convective downdraft and stratiform updraft and downdraft mass fluxes vary notably below the melting level, but share similar vertically uniform draft velocities despite differing hydrometeor loadings. All identified convective and stratiform downdrafts contain precipitation below ~10 km and nearly all updrafts are cloudy above the melting level. Cold pool properties diverge substantially in a manner that is consistent with convective downdraft mass flux differences below the melting level. Despite differences in hydrometeor loadings and cold pool properties, convective updraft and downdraft mass fluxes are linearly correlated with convective area, the ratio of ice in downdrafts to that in updrafts is ~0.5 independent of species, and the ratio of downdraft to updraft mass flux is ~0.5-0.6, which may represent a minimum evaporation efficiency under moist conditions. Hydrometeor loading in stratiform regions is found to be a fraction of hydrometeor loading in convective regions that ranges from ~10% (graupel) to ~90% (cloud ice). These findings may lead to improved convection parameterizations.« less

76 FR 43374 - Proposed Collection; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-20

...'s design and content, using an iterative process to improve the draft form to make it easier for... considered private. Type of Review: New Collection. Affected Public: Individuals and businesses or other for... other forms of information technology; and (e) estimates of capital or start-up costs and costs of...

78 FR 310 - Draft Revision of Guidance for Industry on Providing Regulatory Submissions in Electronic Format...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-03

...ApprovalProcess/FormsSubmissionRequirements/ElectronicSubmissions/ucm253101.htm , http://www.regulations.../Drugs/DevelopmentApprovalProcess/FormsSubmissionRequirements/ElectronicSubmissions/ucm253101.htm , http...), in a format that FDA can process, review, and archive. Currently, the Agency can process, review, and...

Physical Activity Play and Preschool Children's Peer Acceptance: Distinctions between Rough-and-Tumble and Exercise Play

ERIC Educational Resources Information Center

Lindsey, Eric W.

2014-01-01

Research Findings: Two forms of exercise play (toy mediated and non-mediated) and 2 forms of rough-and-tumble (R&T) play (chase and fighting) were examined in relation to preschoolers' peer competence. A total of 148 preschoolers (78 boys, 89 Euro-Americans) were observed during free play at their university-sponsored child care center. The…

Initial draft of CSE-UCLA evaluation model based on weighted product in order to optimize digital library services in computer college in Bali

NASA Astrophysics Data System (ADS)

Divayana, D. G. H.; Adiarta, A.; Abadi, I. B. G. S.

2018-01-01

The aim of this research was to create initial design of CSE-UCLA evaluation model modified with Weighted Product in evaluating digital library service at Computer College in Bali. The method used in this research was developmental research method and developed by Borg and Gall model design. The results obtained from the research that conducted earlier this month was a rough sketch of Weighted Product based CSE-UCLA evaluation model that the design had been able to provide a general overview of the stages of weighted product based CSE-UCLA evaluation model used in order to optimize the digital library services at the Computer Colleges in Bali.

Smart Cameras for Remote Science Survey

NASA Technical Reports Server (NTRS)

Thompson, David R.; Abbey, William; Allwood, Abigail; Bekker, Dmitriy; Bornstein, Benjamin; Cabrol, Nathalie A.; Castano, Rebecca; Estlin, Tara; Fuchs, Thomas; Wagstaff, Kiri L.

2012-01-01

Communication with remote exploration spacecraft is often intermittent and bandwidth is highly constrained. Future missions could use onboard science data understanding to prioritize downlink of critical features [1], draft summary maps of visited terrain [2], or identify targets of opportunity for followup measurements [3]. We describe a generic approach to classify geologic surfaces for autonomous science operations, suitable for parallelized implementations in FPGA hardware. We map these surfaces with texture channels - distinctive numerical signatures that differentiate properties such as roughness, pavement coatings, regolith characteristics, sedimentary fabrics and differential outcrop weathering. This work describes our basic image analysis approach and reports an initial performance evaluation using surface images from the Mars Exploration Rovers. Future work will incorporate these methods into camera hardware for real-time processing.

On the characteristics and scales of outer bank roughness on large meander bends: the influence of bank material properties, floodplain vegetation and flow inundation

USDA-ARS?s Scientific Manuscript database

This paper explores the scales and characteristics of form roughness along the outer banks of two bends on a large meandering river through investigation of irregularities in bank contours and local topographic variability on the bank face. The analysis also examines how roughness varies over the ve...

Influence of surface roughness on the oxidation behavior of a Ni-4.0Cr-5.7Al single crystal superalloy

NASA Astrophysics Data System (ADS)

Pei, Haiqing; Wen, Zhixun; Li, Zhenwei; Zhang, Yamin; Yue, Zhufeng

2018-05-01

The high-temperature oxidation dynamics and mechanisms of a Ni-based single crystal superalloy with four kinds of surface roughnesses were investigated by virtue of XRD, OM, SEM and EDS at 1000 °C. In the initial oxidation stage, outer (Ni, Co)O was mainly produced on the surfaces of the samples with Ra = 90 nm and 19 nm. Correspondingly, outer Cr2O3 and transient θ-Al2O3 were mainly formed on the surfaces with Ra = 509 nm and 182 nm. After 180 min oxidation, the values of instantaneous parabolic mass gain coefficients (kp) of the samples with all surface roughnesses were gradually consistent with the data of the growth parabolic coefficient of α-Al2O3. The oxidation mechanisms of Ni-based superalloy with different surface roughnesses were discussed by a model. The external diffusion flux of Al (DAl) increases with the increases of surface roughness. Thus, the required Al concentration decreases with the increases of surface roughness when the selective oxidation of Al occurrs to form a protective single α-Al2O3 film.

Panel 3: Genetics and Precision Medicine of Otitis Media.

PubMed

Lin, Jizhen; Hafrén, Hena; Kerschner, Joseph; Li, Jian-Dong; Brown, Steve; Zheng, Qing Y; Preciado, Diego; Nakamura, Yoshihisa; Huang, Qiuhong; Zhang, Yan

2017-04-01

Objective The objective is to perform a comprehensive review of the literature up to 2015 on the genetics and precision medicine relevant to otitis media. Data Sources PubMed database of the National Library of Medicine. Review Methods Two subpanels were formed comprising experts in the genetics and precision medicine of otitis media. Each of the panels reviewed the literature in their respective fields and wrote draft reviews. The reviews were shared with all panel members, and a merged draft was created. The entire panel met at the 18th International Symposium on Recent Advances in Otitis Media in June 2015 and discussed the review and refined the content. A final draft was made, circulated, and approved by the panel members. Conclusion Many genes relevant to otitis media have been identified in the last 4 years in advancing our knowledge regarding the predisposition of the middle ear mucosa to commensals and pathogens. Advances include mutant animal models and clinical studies. Many signaling pathways are involved in the predisposition of otitis media. Implications for Practice New knowledge on the genetic background relevant to otitis media forms a basis of novel potential interventions, including potential new ways to treat otitis media.

Evolution of modern approaches to express uncertainty in measurement

NASA Astrophysics Data System (ADS)

Kacker, Raghu; Sommer, Klaus-Dieter; Kessel, Rüdiger

2007-12-01

An object of this paper is to discuss the logical development of the concept of uncertainty in measurement and the methods for its quantification from the classical error analysis to the modern approaches based on the Guide to the Expression of Uncertainty in Measurement (GUM). We review authoritative literature on error analysis and then discuss its limitations which motivated the experts from the International Committee for Weights and Measures (CIPM), the International Bureau of Weights and Measures (BIPM) and various national metrology institutes to develop specific recommendations which form the basis of the GUM. We discuss the new concepts introduced by the GUM and their merits and limitations. The limitations of the GUM led the BIPM Joint Committee on Guides in Metrology to develop an alternative approach—the draft Supplement 1 to the GUM (draft GUM-S1). We discuss the draft GUM-S1 and its merits and limitations. We hope this discussion will lead to a more effective use of the GUM and the draft GUM-S1 and stimulate investigations leading to further improvements in the methods to quantify uncertainty in measurement.

Draft Genome Sequence of a "Candidatus Brocadia" Bacterium Enriched from Activated Sludge Collected in a Tropical Climate.

PubMed

Liu, Xianghui; Arumugam, Krithika; Natarajan, Gayathri; Seviour, Thomas W; Drautz-Moses, Daniela I; Wuertz, Stefan; Law, Yingyu; Williams, Rohan B H

2018-05-10

Here, we present the draft genome sequence of an anaerobic ammonium-oxidizing bacterium (AnAOB), " Candidatus Brocadia," which was enriched in an anammox reactor. A 3.2-Mb genome sequence comprising 168 contigs was assembled, in which 2,765 protein-coding genes, 47 tRNAs, and one each of 5S, 16S, and 23S rRNAs were annotated. No evidence for the presence of a nitric oxide-forming nitrite reductase was found. Copyright © 2018 Liu et al.

Quadrennial Review of Military Compensation (7TH). Global Subject Papers

DTIC Science & Technology

1992-08-01

the added result of reducing officers’ retired pay via a reduction in Basic Pay. The draft report recommends the continuous payment of BAS to all...being eligible for VHA is unfair. However, we also believe a minimum eligibility period is needed. The draft report recommends payment of full housing...93-12040 JOIN form Approved REPORT DOCUMENTATION PACE J No0 *flcrr t 0 datA .,-Vtr A’d :,r.¶tq. ~.-- r’ ~ (F. 0 ’ ~ ~ t’-e’,’ -o..t,7d’ A-t’trt I

Roughness Induced Transition in a Supersonic Boundary Layer

NASA Technical Reports Server (NTRS)

Balakumar, Ponnampalam; Kergerise, Michael A.

2013-01-01

Direct numerical simulation is used to investigate the transition induced by threedimensional isolated roughness elements in a supersonic boundary layer at a free stream Mach number of 3.5. Simulations are performed for two different configurations: one is a square planform roughness and the other is a diamond planform roughness. The mean-flow calculations show that the roughness induces counter rotating streamwise vortices downstream of the roughness. These vortices persist for a long distance downstream and lift the low momentum fluid from the near wall region and place it near the outer part of the boundary layer. This forms highly inflectional boundary layer profiles. These observations agree with recent experimental observations. The receptivity calculations showed that the amplitudes of the mass-flux fluctuations near the neutral point for the diamond shape roughness are the same as the amplitude of the acoustic disturbances. They are three times smaller for the square shape roughness.

Non-linear boundary-layer receptivity due to distributed surface roughness

NASA Technical Reports Server (NTRS)

Amer, Tahani Reffet

1995-01-01

The process by which a laminar boundary layer internalizes the external disturbances in the form of instability waves is known as boundary-layer receptivity. The objective of the present research was to determine the effect of acoustic excitation on boundary-layer receptivity for a flat plate with distributed variable-amplitude surface roughness through measurements with a hot-wire probe. Tollmien-Schlichting mode shapes due to surface roughness receptivity have also been determined, analyzed, and shown to be in agreement with theory and other experimental work. It has been shown that there is a linear relationship between the surface roughness and receptivity for certain roughness configurations with constant roughness wavelength. In addition, strong non-linear receptivity effects exist for certain surface roughness configurations over a band where the surface roughness and T-S wavelength are matched. The results from the present experiment follow the trends predicted by theory and other experimental work for linear receptivity. In addition, the results show the existence of non-linear receptivity effects for certain combinations of surface roughness elements.

Nanoscale investigation on Pseudomonas aeruginosa biofilm formed on porous silicon using atomic force microscopy.

PubMed

Kannan, Ashwin; Karumanchi, Subbalakshmi Latha; Krishna, Vinatha; Thiruvengadam, Kothai; Ramalingam, Subramaniam; Gautam, Pennathur

2014-01-01

Colonization of surfaces by bacterial cells results in the formation of biofilms. There is a need to study the factors that are important for formation of biofilms since biofilms have been implicated in the failure of semiconductor devices and implants. In the present study, the adhesion force of biofilms (formed by Pseudomonas aeruginosa) on porous silicon substrates of varying surface roughness was quantified using atomic force microscopy (AFM). The experiments were carried out to quantify the effect of surface roughness on the adhesion force of biofilm. The results show that the adhesion force increased from 1.5 ± 0.5 to 13.2 ± 0.9 nN with increase in the surface roughness of silicon substrate. The results suggest that the adhesion force of biofilm is affected by surface roughness of substrate. © 2014 Wiley Periodicals, Inc.

Quantitative three-dimensional ice roughness from scanning electron microscopy

NASA Astrophysics Data System (ADS)

Butterfield, Nicholas; Rowe, Penny M.; Stewart, Emily; Roesel, David; Neshyba, Steven

2017-03-01

We present a method for inferring surface morphology of ice from scanning electron microscope images. We first develop a novel functional form for the backscattered electron intensity as a function of ice facet orientation; this form is parameterized using smooth ice facets of known orientation. Three-dimensional representations of rough surfaces are retrieved at approximately micrometer resolution using Gauss-Newton inversion within a Bayesian framework. Statistical analysis of the resulting data sets permits characterization of ice surface roughness with a much higher statistical confidence than previously possible. A survey of results in the range -39°C to -29°C shows that characteristics of the roughness (e.g., Weibull parameters) are sensitive not only to the degree of roughening but also to the symmetry of the roughening. These results suggest that roughening characteristics obtained by remote sensing and in situ measurements of atmospheric ice clouds can potentially provide more facet-specific information than has previously been appreciated.

Development of channel organization and roughness following sediment pulses in single‐thread, gravel bed rivers

USGS Publications Warehouse

Madej, Mary Ann

2001-01-01

Large, episodic inputs of coarse sediment (sediment pulses) in forested, mountain streams may result in changes in the size and arrangement of bed forms and in channel roughness. A conceptual model of channel organization delineates trajectories of response to sediment pulses for many types of gravel bed channels. Channels exhibited self‐organizing behavior to various degrees based on channel gradient, presence of large in‐channel wood or other forcing elements, the size of the sediment pulse, and the number of bed‐mobilizing flows since disturbance. Typical channel changes following a sediment pulse were initial decreases in water depth, in variability of bed elevations, and in the regularity of bed form spacing. Trajectories of change subsequently showed increased average water depth, more variable and complex bed topography, and increased uniformity of bed form spacing. Bed form spacing in streams with abundant forcing elements developed at a shorter spatial scale (two to five channel widths) than in streams without such forcing mechanisms (five to 10 channel widths). Channel roughness increased as bed forms developed.

Effect of ship hull form on the resistance penalty from biofouling.

PubMed

Oliveira, Dinis; Larsson, Ann I; Granhag, Lena

2018-03-01

Hull biofouling is a well-known problem for the shipping industry, leading to increased resistance and fuel consumption. Considering that the effects of hull form on resistance are known to be higher for a less slender hull, it is hypothesised in this paper that the effect of biofouling roughness on resistance is also dependent on the hull form. To test this hypothesis, previously reported full-scale numerical results on a containership are re-analysed. Form effects on roughness penalties, corresponding to K ΔCT  = 0.058 ± 0.025, are observed at a low speed (19 knots, Re s  = 2.29 × 10 9 ), which are however cancelled out by traditionally neglected roughness effects on wave-making resistance at a higher speed (24 knots, Re s  = 2.89 × 10 9 ). It is concluded that hull form effects on biofouling penalties can be significant at low speeds, though not generalisable for higher speeds, namely when wave-making resistance corresponds to ≥ 29% of total resistance.

Purification and characterization of antifungal compounds from Lactobacillus plantarum HD1 isolated from kimchi.

PubMed

Ryu, Eun Hye; Yang, Eun Ju; Woo, Eun Rhan; Chang, Hae Choon

2014-08-01

Strain HD1 with antifungal activity was isolated from kimchi and identified as Lactobacillus plantarum. Antifungal compounds from Lb. plantarum HD1 were active against food- and feed-borne filamentous fungi and yeasts in a spot-on-the-lawn assay. Antifungal activity of Lb. plantarum HD1 was stronger against filamentous fungi than yeast. Antifungal compounds were purified using solid phase extraction (SPE) and recycling preparative-HPLC. Structures of the antifungal compounds were elucidated by electrospray ionization-mass spectrometry and nuclear magnetic resonance. Active compounds from Lb. plantarum HD1 were identified as 5-oxododecanoic acid (MW 214), 3-hydroxy decanoic acid (MW 188), and 3-hydroxy-5-dodecenoic acid (MW 214). To investigate the potential application of these antifungal compounds for reduction of fungal spoilage in foods, Korean draft rice wine was used as a food model. White film-forming yeasts were observed in control draft rice wine after 11 days of incubation. However, film-forming yeasts were not observed in draft rice wine treated with SPE-prepared culture supernatant of Lb. plantarum HD1 (equivalent to 2.5% addition of culture supernatant) until 27 days of incubation. The addition of antifungal compounds to Korean draft rice wine extended shelf-life up to 27 days at 10 °C without any sterilization process. Therefore, the antifungal activity of Lb. plantarum HD1 may lead to the development of powerful biopreservative systems capable of preventing food- and feed-borne fungal spoilage. Copyright © 2014 Elsevier Ltd. All rights reserved.

Electrochemical machining process for forming surface roughness elements on a gas turbine shroud

DOEpatents

Lee, Ching-Pang; Johnson, Robert Alan; Wei, Bin; Wang, Hsin-Pang

2002-01-01

The back side recessed cooling surface of a shroud defining in part the hot gas path of a turbine is electrochemically machined to provide surface roughness elements and spaces therebetween to increase the heat transfer coefficient. To accomplish this, an electrode with insulating dielectric portions and non-insulating portions is disposed in opposition to the cooling surface. By passing an electrolyte between the cooling surface and electrode and applying an electrical current between the electrode and a shroud, roughness elements and spaces therebetween are formed in the cooling surface in opposition to the insulating and non-insulating portions of the electrode, hence increasing the surface area and heat transfer coefficient of the shroud.

Skin friction measurements of systematically-varied roughness: Probing the role of roughness amplitude and skewness

NASA Astrophysics Data System (ADS)

Barros, Julio; Flack, Karen; Schultz, Michael

2017-11-01

Real-world engineering systems which feature either external or internal wall-bounded turbulent flow are routinely affected by surface roughness. This gives rise to performance degradation in the form of increased drag or head loss. However, at present there is no reliable means to predict these performance losses based upon the roughness topography alone. This work takes a systematic approach by generating random surface roughness in which the surface statistics are closely controlled. Skin friction and roughness function results will be presented for two groups of these rough surfaces. The first group is Gaussian (i.e. zero skewness) in which the root-mean-square roughness height (krms) is varied. The second group has a fixed krms, and the skewness is varied from approximately -1 to +1. The effect of the roughness amplitude and skewness on the skin friction will be discussed. Particular attention will be paid to the effect of these parameters on the roughness function in the transitionally-rough flow regime. For example, the role these parameters play in the monotonic or inflectional nature of the roughness function will be addressed. Future research into the details of the turbulence structure over these rough surfaces will also be outlined. Research funded by U.S. Office of Naval Research (ONR).

A new fiber optic sensor for inner surface roughness measurement

NASA Astrophysics Data System (ADS)

Xu, Xiaomei; Liu, Shoubin; Hu, Hong

2009-11-01

In order to measure inner surface roughness of small holes nondestructively, a new fiber optic sensor is researched and developed. Firstly, a new model for surface roughness measurement is proposed, which is based on intensity-modulated fiber optic sensors and scattering modeling of rough surfaces. Secondly, a fiber optical measurement system is designed and set up. Under the help of new techniques, the fiber optic sensor can be miniaturized. Furthermore, the use of micro prism makes the light turn 90 degree, so the inner side surface roughness of small holes can be measured. Thirdly, the fiber optic sensor is gauged by standard surface roughness specimens, and a series of measurement experiments have been done. The measurement results are compared with those obtained by TR220 Surface Roughness Instrument and Form Talysurf Laser 635, and validity of the developed fiber optic sensor is verified. Finally, precision and influence factors of the fiber optic sensor are analyzed.

Using Multi-Dimensional Microwave Remote Sensing Information for the Retrieval of Soil Surface Roughness

NASA Astrophysics Data System (ADS)

Marzahn, P.; Ludwig, R.

2016-06-01

In this Paper the potential of multi parametric polarimetric SAR (PolSAR) data for soil surface roughness estimation is investigated and its potential for hydrological modeling is evaluated. The study utilizes microwave backscatter collected from the Demmin testsite in the North-East Germany during AgriSAR 2006 campaign using fully polarimetric L-Band airborne SAR data. For ground truthing extensive soil surface roughness in addition to various other soil physical properties measurements were carried out using photogrammetric image matching techniques. The correlation between ground truth roughness indices and three well established polarimetric roughness estimators showed only good results for Re[ρRRLL] and the RMS Height s. Results in form of multitemporal roughness maps showed only satisfying results due to the fact that the presence and development of particular plants affected the derivation. However roughness derivation for bare soil surfaces showed promising results.

High-quality permanent draft genome sequence of the Parapiptadenia rigida-nodulating Cupriavidus sp. strain UYPR2.512

DOE Office of Scientific and Technical Information (OSTI.GOV)

De Meyer, Sofie E.; Fabiano, Elena; Tian, Rui

Cupriavidus sp. strain UYPR2.512 is an aerobic, motile, Gram-negative, non-spore-forming rod that was isolated from a root nodule of Parapiptadenia rigida grown in soils from a native forest of Uruguay. Here we describe the features of Cupriavidus sp. strain UYPR2.512, together with sequence and annotation. We find the 7,858,949 bp high-quality permanent draft genome is arranged in 365 scaffolds of 369 contigs, contains 7,411 protein-coding genes and 76 RNA-only encoding genes, and is part of the GEBA-RNB project proposal.

High-quality permanent draft genome sequence of the Parapiptadenia rigida-nodulating Cupriavidus sp. strain UYPR2.512

DOE PAGES

De Meyer, Sofie E.; Fabiano, Elena; Tian, Rui; ...

2015-04-11

Cupriavidus sp. strain UYPR2.512 is an aerobic, motile, Gram-negative, non-spore-forming rod that was isolated from a root nodule of Parapiptadenia rigida grown in soils from a native forest of Uruguay. Here we describe the features of Cupriavidus sp. strain UYPR2.512, together with sequence and annotation. We find the 7,858,949 bp high-quality permanent draft genome is arranged in 365 scaffolds of 369 contigs, contains 7,411 protein-coding genes and 76 RNA-only encoding genes, and is part of the GEBA-RNB project proposal.

Numerical investigation of hypersonic flat-plate boundary layer transition mechanism induced by different roughness shapes

NASA Astrophysics Data System (ADS)

Zhou, Yunlong; Zhao, Yunfei; Xu, Dan; Chai, Zhenxia; Liu, Wei

2016-10-01

The roughness-induced laminar-turbulent boundary layer transition is significant for high-speed aerospace applications. The transition mechanism is closely related to the roughness shape. In this paper, high-order numerical method is used to investigate the effect of roughness shape on the flat-plate laminar-to-turbulent boundary layer transition. Computations are performed in both the supersonic and hypersonic regimes (free-stream Mach number from 3.37 up to 6.63) for the square, cylinder, diamond and hemisphere roughness elements. It is observed that the square and diamond roughness elements are more effective in inducing transition compared with the cylinder and hemisphere ones. The square roughness element has the longest separated region in which strong unsteadiness exists and the absolute instability is formed, thus resulting in the earliest transition. The diamond roughness element has a maximum width of the separated region leading to the widest turbulent wake region far downstream. Furthermore, transition location moves backward as the Mach number increases, which indicates that the compressibility significantly suppresses the roughness-induced boundary layer transition.

75 FR 14206 - Agency Information Collection Activities: Proposed Collection; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-24

... commercial nuclear power plants (NPPs), electric power companies, and any person eligible under the Atomic... or other forms of information technology? A copy of the draft supporting statement may be viewed free...

76 FR 66311 - Draft Documents To Support Submission of an Electronic Common Technical Document; Availability

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-26

.../DevelopmentApprovalProcess/FormsSubmissionRequirements/ElectronicSubmissions/ucm253101.htm , http://www.fda.gov/BiologicsBloodVaccines/GuidanceComplianceRegulatoryInformation/Guidances/default.htm , or http...

Rural settlements dynamics and the prospects of densification strategy in rural Bangladesh.

PubMed

Alam, A F M Ashraful; Asad, Rumana; Enamul Kabir, Md

2016-01-01

Given the year on year decrease of rural farmland and various forms of land degradation through the intrusion of non-farm land uses, the government of Bangladesh has drafted the agrarian reform strategies, primarily to protect the agricultural land from encroachment, conversion, and indiscriminate use. The draft Agricultural Land Protection and Land Use Bill since its inception in 2011 is facing serious uncertainties of implementation due to its borrowed nature from the developed contexts and inadequacy to recognize the local complexities. With a particular focus on the densification component of the draft bill, a semester-long design studio was conducted in consultation with the existing villagers to explore the practicability of the draft bill in the villages of Tetultala and Chhoygharia in the south-western coastal Bangladesh. The findings from the two villages hint that in Bangladesh, the unique and evolving nature of rural settlements dynamics that are disintegrating the rural society from farming practices and the farmland, thereby, unsettling the traditional village-morphology. The settlements dynamics vary from those of the western context; hence, there is an emerging need to build locally situated knowledge towards a feasible rural land reform.

Panel 5: Microbiology and Immunology Panel

PubMed Central

Murphy, Timothy F.; Chonmaitree, Tasnee; Barenkamp, Stephen; Kyd, Jennelle; Nokso-Koivisto, Johanna; Patel, Janak A.; Heikkinen, Terho; Yamanaka, Noboru; Ogra, Pearay; Swords, W. Edward; Sih, Tania; Pettigrew, Melinda M.

2014-01-01

Objective The objective is to perform a comprehensive review of the literature from January 2007 through June 2011 on the virology, bacteriology, and immunology related to otitis media. Data Sources PubMed database of the National Library of Medicine. Review Methods Three subpanels with co-chairs comprising experts in the virology, bacteriology, and immunology of otitis media were formed. Each of the panels reviewed the literature in their respective fields and wrote draft reviews. The reviews were shared with all panel members, and a second draft was created. The entire panel met at the 10th International Symposium on Recent Advances in Otitis Media in June 2011 and discussed the review and refined the content further. A final draft was created, circulated, and approved by the panel. Conclusion Excellent progress has been made in the past 4 years in advancing an understanding of the microbiology and immunology of otitis media. Advances include laboratory-based basic studies, cell-based assays, work in animal models, and clinical studies. Implications for Practice The advances of the past 4 years formed the basis of a series of short-term and long-term research goals in an effort to guide the field. Accomplishing these goals will provide opportunities for the development of novel interventions, including new ways to better treat and prevent otitis media. PMID:23536533

Relationships between topographic roughness and aeolian processes

NASA Technical Reports Server (NTRS)

Greeley, Ronald; Lancaster, N.; Gaddis, L.; Rasmussen, K. R.; White, B. R.; Saunders, R. S.; Wall, S.; Dobrovolskis, Anthony R.; Iversen, J. D.

1991-01-01

The interaction between winds and desert surfaces has important implications for sediment transport on Earth, Mars, and Venus, and for understanding the relationships between radar backscatter and aerodynamic roughness as part of the NASA Shuttle Imaging radar (SIR-C) Mission. Here, researchers report results from measurements of boundary layer wind profiles and surface roughness at sites in Death Valley and discuss their implications. The sites included a flat to undulating gravel and sand reg, alluvial fans, and a playa. Estimates of average particle size composition of Death Valley sites and arithmetic mean values of aerodynamic roughness are given in tabular form.

Simulation of leakage through mechanical sealing device

NASA Astrophysics Data System (ADS)

Tikhomorov, V. P.; Gorlenko, O. A.; Izmerov, M. A.

2018-03-01

The procedure of mathematical modeling of leakage through the mechanical seal taking into account waviness and roughness is considered. The percolation process is represented as the sum of leakages through a gap between wavy surfaces and percolation through gaps formed by fractal roughness, i.e. the total leakage is determined by the slot model and filtration leakage. Dependences of leaks on the contact pressure of corrugated and rough surfaces of the mechanical seal elements are presented.

Forest research notes, Pacific Northwest Forest Experiment Station, No. 07, August 13, 1931.

Treesearch

1931-01-01

A recently completed study of the sawmill "waste" in the Douglas fir region of Oregon and Washington shows that in the production of 1929 cute of rough green, rough-sawn lumber (10,286,554,000 board feet), 1,552,865,251 cubic feet (solid measure) of sound wood in sawlog form were used. Of this 66.61 per cent (910,010,322 cu.ft.) was converted into rough-green...

CFD based draft tube hydraulic design optimization

NASA Astrophysics Data System (ADS)

McNabb, J.; Devals, C.; Kyriacou, S. A.; Murry, N.; Mullins, B. F.

2014-03-01

The draft tube design of a hydraulic turbine, particularly in low to medium head applications, plays an important role in determining the efficiency and power characteristics of the overall machine, since an important proportion of the available energy, being in kinetic form leaving the runner, needs to be recovered by the draft tube into static head. For large units, these efficiency and power characteristics can equate to large sums of money when considering the anticipated selling price of the energy produced over the machine's life-cycle. This same draft tube design is also a key factor in determining the overall civil costs of the powerhouse, primarily in excavation and concreting, which can amount to similar orders of magnitude as the price of the energy produced. Therefore, there is a need to find the optimum compromise between these two conflicting requirements. In this paper, an elaborate approach is described for dealing with this optimization problem. First, the draft tube's detailed geometry is defined as a function of a comprehensive set of design parameters (about 20 of which a subset is allowed to vary during the optimization process) and are then used in a non-uniform rational B-spline based geometric modeller to fully define the wetted surfaces geometry. Since the performance of the draft tube is largely governed by 3D viscous effects, such as boundary layer separation from the walls and swirling flow characteristics, which in turn governs the portion of the available kinetic energy which will be converted into pressure, a full 3D meshing and Navier-Stokes analysis is performed for each design. What makes this even more challenging is the fact that the inlet velocity distribution to the draft tube is governed by the runner at each of the various operating conditions that are of interest for the exploitation of the powerhouse. In order to determine these inlet conditions, a combined steady-state runner and an initial draft tube analysis, using a stage interface between them, must first be performed for each operating condition. Due to the computationally intensive nature of the evaluation process, the efficiency of the optimization algorithm becomes important. Therefore, a state-of-the-art hierarchical-metamodel-assisted evolutionary algorithm is used.

Three-dimensional structure of dominant instabilities in turbulent flow over smooth and rough boundaries

NASA Astrophysics Data System (ADS)

Grass, A. J.; Stuart, R. J.; Mansour-Tehrani, M.

1991-01-01

The current status of knowledge regarding coherent vortical structures in turbulent boundary layers and their role in turbulence generation are reviewed. The investigations reported in the study concentrate attention on rough-wall flows prevailing in the geophysical environment and include an experiment determining the three-dimensional form of the turbulence structures linked to the ejection and inrush events observed over rough walls and an experiment concerned with measuring the actual spanwise scale of the near-wall structures for boundary conditions ranging from hydrodynamically smooth to fully rough. It is demonstrated that horseshoe vortical structures are present and play an important role in rough-wall flows and they increase in scale with increasing wall distance, while a dominant spanwise wavelength occurs in the instantaneous cross-flow distribution of streamwise velocity close to the rough wall.

Reflected GPS Power for the Detection of Surface Roughness Patterns in Coastal Water

NASA Technical Reports Server (NTRS)

Oertel, George, F.; Allen, Thomas R.

2000-01-01

Coastal bays formed by the barrier islands of Delaware, Maryland and Virginia are parts of a coastal region known as a "Coastal Compartment". The coastal compartment between the Chesapeake and Delaware Bays is actually the mosaic of landscapes on the headland of the interfluve that separates these large drainage basins. The coastal compartments form a variety of different-shaped waterways landward of the coastline. Shape differences along the boundaries produce differences in exposure to wind and waves. Different shoreface topographies seaward of the coastline also influence surface roughness by changing wave-refraction patterns. Surface-water roughness (caused by waves) is controlled by a number of parameters, including fetch, shielding, exposure corridors, water-mass boundary conditions, wetland vegetation and water depth in coastal bays. In the coastal ocean, surface roughness patterns are controlled by shoreface shoaling and inlet refraction patterns in the coastal ocean. Knowledge of wave phenomena in the nearshore and backbarrier areas is needed to understand how wave climate influences important ecosystems in estuaries and bays.

Scoring Package

National Institute of Standards and Technology Data Gateway

NIST Scoring Package (PC database for purchase)   The NIST Scoring Package (Special Database 1) is a reference implementation of the draft Standard Method for Evaluating the Performance of Systems Intended to Recognize Hand-printed Characters from Image Data Scanned from Forms.

75 FR 29352 - Draft Guidance for Industry on Data Elements for Submission of Veterinary Adverse Event Reports...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-25

... filling out form FDA 1932, ``Veterinary Adverse Drug Reaction, Lack of Effectiveness, Product Defect... Drug Reaction, Lack of Effectiveness, Product Defect Report.'' II. Significance of Guidance This level...

Radar-aeolian roughness project

NASA Technical Reports Server (NTRS)

Greeley, Ronald; Dobrovolskis, A.; Gaddis, L.; Iversen, J. D.; Lancaster, N.; Leach, Rodman N.; Rasnussen, K.; Saunders, S.; Vanzyl, J.; Wall, S.

1991-01-01

The objective is to establish an empirical relationship between measurements of radar, aeolian, and surface roughness on a variety of natural surfaces and to understand the underlying physical causes. This relationship will form the basis for developing a predictive equation to derive aeolian roughness from radar backscatter. Results are given from investigations carried out in 1989 on the principal elements of the project, with separate sections on field studies, radar data analysis, laboratory simulations, and development of theory for planetary applications.

A possibility of avoiding surface roughness due to insects

NASA Technical Reports Server (NTRS)

Wortmann, F. X.

1984-01-01

Discussion of a method for eliminating turbulence caused by the formation of insect roughness upon the leading edges and fuselage, particularly in aircraft using BLC. The proposed technique foresees the use of elastic surfaces on which insect roughness cannot form. The operational characteristics of highly elastic rubber surface fastened to the wing leading edges and fuselage edges are examined. Some preliminary test results are presented. The technique is seen to be advantageous primarily for short-haul operations.

Surface roughness of denture bases after immersion in fishcake vinegar solution

NASA Astrophysics Data System (ADS)

Kodir, K.; Tanti, I.; Odang, R. W.

2017-08-01

Fishcake is a common food in Palembang city and is usually eaten with fishcake vinegar sauce. Fishcake vinegar solution contains acetic acid and chloride and fluoride ions, all of which cause surface roughness on the denture base material. The objective of this study was to analyze the effect of fishcake vinegar solution on the surface roughness of heat-cured acrylic resin, thermoplastic nylon, and cobalt-chromium alloy denture bases. This laboratory-based experimental study was performed on heat-cured acrylic resins, thermoplastic nylon specimen plates formed in 15 × 10 × 1 mm shapes, and cobalt-chromium alloy specimens in cylinder forms with a 7.7 mm diameter and 17.5-mm height. Each group consisted of 10 pieces. Each specimen was immersed in a fishcake vinegar solution at 37 °C for 4 days. The surface roughness was measured using a profilometer before and after immersion. Statistical analyses showed significant (p < 0.05) changes in heat-cured acrylic resin, thermoplastic nylon, and the cobalt chromium alloy plates after immersion in a fishcake vinegar solution for 4 days. Fishcake vinegar solution affects the surface roughness of heat-cured acrylic resin, thermoplastic nylon, and cobalt-chromium alloy plates after a 4-day immersion period. The greatest surface roughness change occurred in the thermoplastic nylon plate, while the lowest change occurred in the cobalt-chromium alloy.

CJ2 Icing Effects Simulator. Delivery Order 0019: Development of an Icing Effects Simulation for a Typical Business Jet Configuration

DTIC Science & Technology

2007-08-01

considered were: - Icing protection system failure ice - Inter-cycle (roughness) ice - Run-back ice. The study entailed wind tunnel tests of different...jet that incorporates the effects of various forms of ice. The ice conditions considered were:  Icing protection system failure ice  Inter-cycle...accretions. These were pre-activation roughness, runback shapes that form downstream of the thermal wing ice protection system , and a wing ice

Sabots, Obturator and Gas-In-Launch Tube Techniques for Heat Flux Models in Ballistic Ranges

NASA Technical Reports Server (NTRS)

Bogdanoff, David W.; Wilder, Michael C.

2013-01-01

For thermal protection system (heat shield) design for space vehicle entry into earth and other planetary atmospheres, it is essential to know the augmentation of the heat flux due to vehicle surface roughness. At the NASA Ames Hypervelocity Free Flight Aerodynamic Facility (HFFAF) ballistic range, a campaign of heat flux studies on rough models, using infrared camera techniques, has been initiated. Several phenomena can interfere with obtaining good heat flux data when using this measuring technique. These include leakage of the hot drive gas in the gun barrel through joints in the sabot (model carrier) to create spurious thermal imprints on the model forebody, deposition of sabot material on the model forebody, thereby changing the thermal properties of the model surface and unknown in-barrel heating of the model. This report presents developments in launch techniques to greatly reduce or eliminate these problems. The techniques include the use of obturator cups behind the launch package, enclosed versus open front sabot designs and the use of hydrogen gas in the launch tube. Attention also had to be paid to the problem of the obturator drafting behind the model and impacting the model. Of the techniques presented, the obturator cups and hydrogen in the launch tube were successful when properly implemented

Rough flows and homogenization in stochastic turbulence

NASA Astrophysics Data System (ADS)

Bailleul, I.; Catellier, R.

2017-10-01

We provide in this work a tool-kit for the study of homogenisation of random ordinary differential equations, under the form of a friendly-user black box based on the technology of rough flows. We illustrate the use of this setting on the example of stochastic turbulence.

Effect of microrelief on water erosion and their changes during rainfall

USDA-ARS?s Scientific Manuscript database

Soil surface roughness contains two elementary forms, i.e., depressions and mounds, which affect water flow on the surface differently. While depressions serve as temporary water storage, mounds diverge water away from their local summits. Although roughness effects on runoff and sediment production...

Rough SERS substrate based on gold coated porous silicon layer prepared on the silicon backside surface

NASA Astrophysics Data System (ADS)

Dridi, H.; Haji, L.; Moadhen, A.

2017-04-01

We report in this paper a novel method to elaborate rough Surface Enhanced Raman Scattering (SERS) substrate. A single layer of porous silicon was formed on the silicon backside surface. Morphological characteristics of the porous silicon layer before and after gold deposition were influenced by the rough character (gold size). The reflectance measurements showed a dependence of the gold nano-grains size on the surface nature, through the Localized Surface Plasmon (LSP) band properties. SERS signal of Rhodamine 6G used as a model analyte, adsorbed on the rough porous silicon layer revealed a marked enhancement of its vibrational modes intensities.

Stability of micro-Cassie states on rough substrates

NASA Astrophysics Data System (ADS)

Guo, Zhenjiang; Liu, Yawei; Lohse, Detlef; Zhang, Xuehua; Zhang, Xianren

2015-06-01

We numerically study different forms of nanoscale gaseous domains on a model for rough surfaces. Our calculations based on the constrained lattice density functional theory show that the inter-connectivity of pores surrounded by neighboring nanoposts, which model the surface roughness, leads to the formation of stable microscopic Cassie states. We investigate the dependence of the stability of the micro-Cassie states on substrate roughness, fluid-solid interaction, and chemical potential and then address the differences between the origin of the micro-Cassie states and that of surface nanobubbles within similar models. Finally, we show that the micro-Cassie states share some features with experimentally observed micropancakes at solid-water interfaces.

76 FR 5566 - Notice of Availability for the Draft Programmatic Environmental Assessment for the Development...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-01

... consider other forms of renewable energy. The purpose of the proposed action is to reduce dependency on fossil fuels and increase energy security and efficiency through development of small-scale wind energy...

Effects of roughness and permeability on solute transfer at the sediment water interface.

PubMed

Han, Xu; Fang, Hongwei; He, Guojian; Reible, Danny

2018-02-01

Understanding the mechanisms of solute transfer across the sediment-water interface plays a crucial role in water quality prediction and management. In this study, different arranged particles are used to form typical rough and permeable beds. Large Eddy Simulation (LES) is used to model the solute transfer from the overlying water to sediment beds. Three rough wall turbulence regimes, i.e., smooth, transitional and rough regime, are separately considered and the effects of bed roughness on solute transfer are quantitatively analyzed. Results show that the classic laws related to Schmidt numbers can well reflect the solute transfer under the smooth regime with small roughness Reynolds numbers. Under the transitional regime, the solute transfer coefficient (K L + ) is enhanced and the effect of Schmidt number is weakened by increasing roughness Reynolds number. Under the rough regime, the solute transfer is suppressed by the transition layer (Brinkman layer) and controlled by the bed permeability. Moreover, it is found that water depth, friction velocity and bed permeability can be used to estimate the solute transfer velocity (K L ) under the completely rough regime. Copyright © 2017 Elsevier Ltd. All rights reserved.

Influence of the three-dimensional heterogeneous roughness on electrokinetic transport in microchannels.

PubMed

Hu, Yandong; Werner, Carsten; Li, Dongqing

2004-12-15

Surface roughness has been considered as a passive means of enhancing species mixing in electroosmotic flow through microfluidic systems. It is highly desirable to understand the synergetic effect of three-dimensional (3D) roughness and surface heterogeneity on the electrokinetic flow through microchannels. In this study, we developed a three-dimensional finite-volume-based numerical model to simulate electroosmotic transport in a slit microchannel (formed between two parallel plates) with numerous heterogeneous prismatic roughness elements arranged symmetrically and asymmetrically on the microchannel walls. We consider that all 3D prismatic rough elements have the same surface charge or zeta potential, the substrate (the microchannel wall) surface has a different zeta potential. The results showed that the rough channel's geometry and the electroosmotic mobility ratio of the roughness elements' surface to that of the substrate, epsilon(mu), have a dramatic influence on the induced-pressure field, the electroosmotic flow patterns, and the electroosmotic flow rate in the heterogeneous rough microchannels. The associated sample-species transport presents a tidal-wave-like concentration field at the intersection between four neighboring rough elements under low epsilon(mu) values and has a concentration field similar to that of the smooth channels under high epsilon(mu) values.

Prediction of an internal boundary layer on a flat plate after a step change in roughness using a near-wall RANS model

NASA Astrophysics Data System (ADS)

Chu, Minghan; Meng, Fanxiao; Bergstrom, Donald J.

2017-11-01

An in-house computational fluid dynamics code was used to simulate turbulent flow over a flat plate with a step change in roughness, exhibiting a smooth-rough-smooth configuration. An internal boundary layer (IBL) is formed at the transition from the smooth to rough (SR) and then the rough to smooth (RS) surfaces. For an IBL the flow far above the surface has experienced a wall shear stress that is different from the local value. Within a Reynolds-Averaged-Navier-Stokes (RANS) formulation, the two-layer k- ɛ model of Durbin et al. (2001) was implemented to analyze the response of the flow to the change in surface condition. The numerical results are compared to experimental data, including some in-house measurements and the seminal work of Antonia and Luxton (1971,72). This problem captures some aspects of roughness in industrial and environmental applications, such as corrosion and the earth's surface heterogeneity, where the roughness is often encountered as discrete distributions. It illustrates the challenge of incorporating roughness models in RANS that are capable of responding to complex surface roughness profiles.

Feather roughness reduces flow separation during low Reynolds number glides of swifts.

PubMed

van Bokhorst, Evelien; de Kat, Roeland; Elsinga, Gerrit E; Lentink, David

2015-10-01

Swifts are aerodynamically sophisticated birds with a small arm and large hand wing that provides them with exquisite control over their glide performance. However, their hand wings have a seemingly unsophisticated surface roughness that is poised to disturb flow. This roughness of about 2% chord length is formed by the valleys and ridges of overlapping primary feathers with thick protruding rachides, which make the wing stiffer. An earlier flow study of laminar-turbulent boundary layer transition over prepared swift wings suggested that swifts can attain laminar flow at a low angle of attack. In contrast, aerodynamic design theory suggests that airfoils must be extremely smooth to attain such laminar flow. In hummingbirds, which have similarly rough wings, flow measurements on a 3D printed model suggest that the flow separates at the leading edge and becomes turbulent well above the rachis bumps in a detached shear layer. The aerodynamic function of wing roughness in small birds is, therefore, not fully understood. Here, we performed particle image velocimetry and force measurements to compare smooth versus rough 3D-printed models of the swift hand wing. The high-resolution boundary layer measurements show that the flow over rough wings is indeed laminar at a low angle of attack and a low Reynolds number, but becomes turbulent at higher values. In contrast, the boundary layer over the smooth wing forms open laminar separation bubbles that extend beyond the trailing edge. The boundary layer dynamics of the smooth surface varies non-linearly as a function of angle of attack and Reynolds number, whereas the rough surface boasts more consistent turbulent boundary layer dynamics. Comparison of the corresponding drag values, lift values and glide ratios suggests, however, that glide performance is equivalent. The increased structural performance, boundary layer robustness and equivalent aerodynamic performance of rough wings might have provided small (proto) birds with an evolutionary window to high glide performance. © 2015. Published by The Company of Biologists Ltd.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tian, Rui; Parker, Matthew; Seshadri, Rekha

Bradyrhizobiumsp. Tv2a.2 is an aerobic, motile, Gram-negative, non-spore-forming rod that was isolated from an effective nitrogen-fixing root nodule of Tachigali versicolor collected in Barro Colorado Island of Panama. Here we describe the features of Bradyrhizobiumsp. Tv2a.2, together with high-quality permanent draft genome sequence information and annotation. The 8,496,279 bp high-quality draft genome is arranged in 87 scaffolds of 87 contigs, contains 8,109 protein-coding genes and 72 RNA-only encoding genes. In conclusion, this rhizobial genome was sequenced as part of the DOE Joint Genome Institute 2010 Genomic Encyclopedia for Bacteria and Archaea-Root Nodule Bacteria (GEBA-RNB) project.

High-quality draft genome sequence of Effusibacillus lacus strain skLN1T, facultative anaerobic spore-former isolated from freshwater lake sediment.

PubMed

Watanabe, Miho; Tokizawa, Riho; Kojima, Hisaya; Fukui, Manabu

2017-01-01

10.1601/nm.25721 strain skLN1 T is the type strain of the type species in the genus 10.1601/nm.25720 which is the one of the genera in the family 10.1601/nm.5070 within the phylum 10.1601/nm.3874. 10.1601/nm.25721 strain skLN1 T is a Gram-positive, spore-forming thermophilic neutrophile isolated from freshwater lake sediment. Here, we present the draft genome sequence of strain skLN1 T , which consists of 3,902,380 bp with a G + C content of 50.38%.

Studies of the Combined Effects of Roughness and Reynolds Number in Turbulent Boundary Layers

NASA Astrophysics Data System (ADS)

Mehdi, Faraz; Klewicki, Joseph

2010-11-01

Mehdi, Klewicki & White [Physica D 239(2010)] provide evidence from existing studies that the prevalent scheme for classifying roughness regimes is likely to be incomplete. To further pursue these findings, more data are required, and for this purpose, additional rough-wall experiments are being performed. We report on our studies of the combined roughness-Reynolds number problem conducted in a 8m long wind-tunnel. The roughness considered is the randomly distributed type and introduced in the form of 24-grit sandpaper and pea gravel. The primary measurement tool is two-component LDV. The basis of the analysis is the mean equation of dynamics. In this regard, the length scale defining where the mean dynamics become dominated by inertia is of central importance.

Characteristics of secondary flows in rough-wall turbulent boundary layers

NASA Astrophysics Data System (ADS)

Vanderwel, Christina; Ganapathisubramani, Bharathram

2015-11-01

Large-scale secondary motions consisting of counter-rotating vortices and low- and high-momentum pathways can form in boundary layers that develop over rough surfaces. We experimentally investigated the sensitivity of these secondary motions to spanwise arrangement of the roughness by studying the flow over streamwise-aligned rows of elevated roughness with systematically-varied spacing. The roughness is created with LEGO blocks mounted along the floor of the wind tunnel and Stereo-PIV is used to measure the velocity field in a cross-plane. Results show that the secondary flows are strongest when the spanwise spacing of the surface topology is comparable with the boundary layer thickness. We discuss how these results are relevant to flows over arbitrary topologies and how these secondary motions influence the Reynolds stress distribution in the boundary layer.

Shear Stress Partitioning in Large Patches of Roughness in the Atmospheric Inertial Sublayer

NASA Technical Reports Server (NTRS)

Gillies, John A.; Nickling, William G.; King, James

2007-01-01

Drag partition measurements were made in the atmospheric inertial sublayer for six roughness configurations made up of solid elements in staggered arrays of different roughness densities. The roughness was in the form of a patch within a large open area and in the shape of an equilateral triangle with 60 m long sides. Measurements were obtained of the total shear stress (tau) acting on the surfaces, the surface shear stress on the ground between the elements (tau(sub S)) and the drag force on the elements for each roughness array. The measurements indicated that tau(sub S) quickly reduced near the leading edge of the roughness compared with tau, and a tau(sub S) minimum occurs at a normalized distance (x/h, where h is element height) of approx. -42 (downwind of the roughness leading edge is negative), then recovers to a relatively stable value. The location of the minimum appears to scale with element height and not roughness density. The force on the elements decreases exponentially with normalized downwind distance and this rate of change scales with the roughness density, with the rate of change increasing as roughness density increases. Average tau(sub S): tau values for the six roughness surfaces scale predictably as a function of roughness density and in accordance with a shear stress partitioning model. The shear stress partitioning model performed very well in predicting the amount of surface shear stress, given knowledge of the stated input parameters for these patches of roughness. As the shear stress partitioning relationship within the roughness appears to come into equilibrium faster for smaller roughness element sizes it would also appear the shear stress partitioning model can be applied with confidence for smaller patches of smaller roughness elements than those used in this experiment.

Formulation of Policy for Cyber Crime in Criminal Law Revision Concept of Bill Book of Criminal Law (A New Penal Code)

NASA Astrophysics Data System (ADS)

Soponyono, Eko; Deva Bernadhi, Brav

2017-04-01

Development of national legal systems is aimed to establish the public welfare and the protection of the public. Many attempts has been carried out to renew material criminal law and those efforts results in the formulation of the concept of the draft Law Book of the Law of Criminal Law in the form of concept criminal code draft. The basic ideas in drafting rules and regulation based on the values inside the idology of Pancasila are balance among various norm and rules in society. The design concept of the New Criminal Code Act is anticipatory and proactive to formulate provisions on Crime in Cyberspace and Crime on Information and Electronic Transactions. Several issues compiled in this paper are whether the policy in formulation of cyber crime is embodied in the provisions of the current legislation and what the policies formulation of cyber crime is in the concept of the bill book of law - criminal law recently?.

Development and characterization of a layer by layer ultrasound assisted spray deposition process for thin polymer films

NASA Astrophysics Data System (ADS)

Balakrishnan, Anandh

An Ultrasound assisted Atomization (UA) system has been developed and investigated to synthesize ˜20microm polyurethane thin films with uniform, repeatable thickness and microstructure. The UA system comprised a 20 kHz atomizer probe mounted on 750 W/cm2 transducer, a heated glass chamber and a rotating substrate. The rationale for the work has been built through a careful Design of Experiments (DoE) that sought to answer questions regarding the process-microstructure relationships from both the spray and material points of view. The independent variables chosen were the polymer solution weight percentage (0.2%, 2%, and 4%), power amplitude (energy) percentage supplied to the nozzle (23%, 29%, 37%, and 46%),the temperature of deposition (45°C, 80°C) and flow rate (50microL/min, 150microL/min). The research questions focused on influence of the process parameters on the microstructure and properties of the film. One of the problems involved fixing the trajectory of the spray and also making use of the droplet surfaces created by the spray. To achieve this, a simple air-draft attachment was devised and the influence of the same was evaluated through process and film characterization experiments. A mechanism for the draft has been schematically provided. The use of such a draft to fabricate thin polymer films via ultrasound atomization has not been achieved before and represents a 'first step' in advancing this ultrasound technology. The primary findings of the work were that the film microstructure and properties were heavily influenced by the flow rate, energy of atomization, and test temperature. In addition, the droplet diameters seemed to be readily amenable to change for the 0.2 and 2% solutions and the use of the air-draft made the process feasible, repeatable and accurate. For the 4% solutions, viscosity seemed to stabilize the liquid solution film at the tip requiring larger energies of atomization. In all, relative to the 0.2% films the fracture strengths, strains and toughness values had improved vastly for 4% and 2%. Calorimetric, Small Angle X-ray scattering and Atomic Force Microscopy (AFM) measurements showed a largely phase mixed hard segment-soft segment morphology. Calorimetry showed that the 0.2% specimens showed higher melting points (between 110--130°C) indicative of greater hard domain ordering in these samples. This is not evident in the 2% and 4% samples. This trend is supported by the Small Angle X-ray scattering and AFM data. The X-ray data show larger domain sizes and greater invariants for the 0.2% samples relative to the 2% and 4% samples. The AFM phase image measurements provided hard domain widths in the same range as the X-ray measurements (10--11 nm). All of the topographical trends from AFM showed that surface morphology was affected by i) increasing atomization energies from 29%--46% of energy (decreased surface roughness from 3 nm to 2 nm for 2% films and 1 nm to 0.5 nm for 4% films); ii) increasing film fabrication temperature from 45°C--80°C (increased roughness from 3nm to 4--5nm in local spots for 2% films and from 0.5nm to 0.6 nm for 4% films), iii) decreasing flow rate of the pump from 150microL/min to 50microL/min (comparable roughness for the case of the 2% films from 3nm to 2nm). These could explain the trends in mechanical responses as a f( energy of atomization and temperature). In order to examine sample crystallinity, we performed Wide Angle X-ray Scattering which showed a fully amorphous polymer structure. The lack of any reflections indicated that the melting points observed from calorimetry were not due to long range order in the material but due to pseudo crystalline behavior. This behavior could be ascribed to the formation of urethane-urethane ordering with hydrogen bonds between them. In general, ultrasonic energy of the capillary wave causes phase mixing and the extent of phase mixing was dependent on the weight percentage of polymer solution and the type of solvent. It was highest for the 4% samples and lowest for the 0.2% samples.

39 CFR 775.11 - Environmental impact statements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... approaches or generally accepted research methods. For purposes of this subsection, “reasonably foreseeable...)), the environmental impacts and the alternatives are presented in comparative form, thus sharply... comparative merits. (iii) Identify the preferred alternative or alternatives in the draft and final statements...

39 CFR 775.11 - Environmental impact statements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... approaches or generally accepted research methods. For purposes of this subsection, “reasonably foreseeable...)), the environmental impacts and the alternatives are presented in comparative form, thus sharply... comparative merits. (iii) Identify the preferred alternative or alternatives in the draft and final statements...

39 CFR 775.11 - Environmental impact statements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... approaches or generally accepted research methods. For purposes of this subsection, “reasonably foreseeable...)), the environmental impacts and the alternatives are presented in comparative form, thus sharply... comparative merits. (iii) Identify the preferred alternative or alternatives in the draft and final statements...

39 CFR 775.11 - Environmental impact statements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... approaches or generally accepted research methods. For purposes of this subsection, “reasonably foreseeable...)), the environmental impacts and the alternatives are presented in comparative form, thus sharply... comparative merits. (iii) Identify the preferred alternative or alternatives in the draft and final statements...

39 CFR 775.11 - Environmental impact statements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... approaches or generally accepted research methods. For purposes of this subsection, “reasonably foreseeable...)), the environmental impacts and the alternatives are presented in comparative form, thus sharply... comparative merits. (iii) Identify the preferred alternative or alternatives in the draft and final statements...

The Role of Law-of-the-Wall and Roughness Scale in the Surface Stress Model for LES of the Rough-wall Boundary Layer

NASA Astrophysics Data System (ADS)

Brasseur, James; Paes, Paulo; Chamecki, Marcelo

2017-11-01

Large-eddy simulation (LES) of the high Reynolds number rough-wall boundary layer requires both a subfilter-scale model for the unresolved inertial term and a ``surface stress model'' (SSM) for space-time local surface momentum flux. Standard SSMs assume proportionality between the local surface shear stress vector and the local resolved-scale velocity vector at the first grid level. Because the proportionality coefficient incorporates a surface roughness scale z0 within a functional form taken from law-of-the-wall (LOTW), it is commonly stated that LOTW is ``assumed,'' and therefore ``forced'' on the LES. We show that this is not the case; the LOTW form is the ``drag law'' used to relate friction velocity to mean resolved velocity at the first grid level consistent with z0 as the height where mean velocity vanishes. Whereas standard SSMs do not force LOTW on the prediction, we show that parameterized roughness does not match ``true'' z0 when LOTW is not predicted, or does not exist. By extrapolating mean velocity, we show a serious mismatch between true z0 and parameterized z0 in the presence of a spurious ``overshoot'' in normalized mean velocity gradient. We shall discuss the source of the problem and its potential resolution.

Roughness Based Crossflow Transition Control for a Swept Airfoil Design Relevant to Subsonic Transports

NASA Technical Reports Server (NTRS)

Li, Fei; Choudhari, Meelan M.; Carpenter, Mark H.; Malik, Mujeeb R.; Eppink, Jenna; Chang, Chau-Lyan; Streett, Craig L.

2010-01-01

A high fidelity transition prediction methodology has been applied to a swept airfoil design at a Mach number of 0.75 and chord Reynolds number of approximately 17 million, with the dual goal of an assessment of the design for the implementation and testing of roughness based crossflow transition control and continued maturation of such methodology in the context of realistic aerodynamic configurations. Roughness based transition control involves controlled seeding of suitable, subdominant crossflow modes in order to weaken the growth of naturally occurring, linearly more unstable instability modes via a nonlinear modification of the mean boundary layer profiles. Therefore, a synthesis of receptivity, linear and nonlinear growth of crossflow disturbances, and high-frequency secondary instabilities becomes desirable to model this form of control. Because experimental data is currently unavailable for passive crossflow transition control for such high Reynolds number configurations, a holistic computational approach is used to assess the feasibility of roughness based control methodology. Potential challenges inherent to this control application as well as associated difficulties in modeling this form of control in a computational setting are highlighted. At high Reynolds numbers, a broad spectrum of stationary crossflow disturbances amplify and, while it may be possible to control a specific target mode using Discrete Roughness Elements (DREs), nonlinear interaction between the control and target modes may yield strong amplification of the difference mode that could have an adverse impact on the transition delay using spanwise periodic roughness elements.

Can high resolution topographic surveys provide reliable grain size estimates?

NASA Astrophysics Data System (ADS)

Pearson, Eleanor; Smith, Mark; Klaar, Megan; Brown, Lee

2017-04-01

High resolution topographic surveys contain a wealth of information that is not always exploited in the generation of Digital Elevation Models (DEMs). In particular, several authors have related sub-grid scale topographic variability (or 'surface roughness') to particle grain size by deriving empirical relationships between the two. Such relationships would permit rapid analysis of the spatial distribution of grain size over entire river reaches, providing data to drive distributed hydraulic models and revolutionising monitoring of river restoration projects. However, comparison of previous roughness-grain-size relationships shows substantial variability between field sites and do not take into account differences in patch-scale facies. This study explains this variability by identifying the factors that influence roughness-grain-size relationships. Using 275 laboratory and field-based Structure-from-Motion (SfM) surveys, we investigate the influence of: inherent survey error; irregularity of natural gravels; particle shape; grain packing structure; sorting; and form roughness on roughness-grain-size relationships. A suite of empirical relationships is presented in the form of a decision tree which improves estimations of grain size. Results indicate that the survey technique itself is capable of providing accurate grain size estimates. By accounting for differences in patch facies, R2 was seen to improve from 0.769 to R2 > 0.9 for certain facies. However, at present, the method is unsuitable for poorly sorted gravel patches. In future, a combination of a surface roughness proxy with photosieving techniques using SfM-derived orthophotos may offer improvements on using either technique individually.

Specimen preparation for x-ray fluorescence analysis of solutions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eksperiandova, L.P.; Spolnik, Z.M.; Blank, A.B.

1995-12-31

Specimens for x-ray fluorescence analysis (XRFA) were prepared by adding dry gelatine (10%) to the analysis solution, homogenizing the mixture and cooling for 20 minutes. Thus, a compact resilient mass could be formed with the required shape and size; the roughness of the surface was determined by the roughness of the surface on which the specimen was formed, much the same as highly polished. Various calibration methods can be applied in the XRFA of a variety of materials if such specimens are used. 12 refs., 1 fig., 2 tabs.

Roughness topographical effects on mean momentum and stress budgets in developed turbulent channel flows

NASA Astrophysics Data System (ADS)

Aghaei Jouybari, Mostafa; Yuan, Junlin

2017-11-01

Direct numerical simulations of turbulent channel flows are carried out over two surfaces: a synthesized sand-grain surface and a realistic turbine roughness that is characterized by more prominent large-scale surface features. To separate the effects of wall-normal variation of the roughness area fraction from the (true) variation of flow statistics, the governing equations are area-averaged using intrinsic averaging, contrary to the usually practice based on the total area (i.e., superficial averaging). Additional terms appear in the mean-momentum equation resulted from the wall-normal variation of the solid fraction and play a role in the near-wall balance. Results from surfaces with a step solidity function (e.g., cubes) will also be discussed. Compared to the sand grains, the turbine surface generates stronger form-induced fluctuations, despite weaker dispersive shear stress. This is associated with more significant form-induced productions (comparable to shear production) in Reynolds stress budgets, weaker pressure work, and, consequently, more anisotropic redistribution of turbulent kinetic energy in the roughness sublayer, which potentially leads to different turbulent responses between the two surfaces in non-equilibrium flows.

Research on the Additional Secondary Phase Factor for Automatic Identification System Signals Transmitted over a Rough Sea Surface

PubMed Central

Zhang, Shufang; Sun, Xiaowen

2018-01-01

This paper investigates the Additional Secondary Phase Factor (ASF) characteristics of Automatic Identification System (AIS) signals spreading over a rough sea surface. According to the change of the ASFs for AIS signals in different signal form, the influences of the different propagation conditions on the ASFs are analyzed. The expression, numerical calculation, and simulation analysis of the ASFs of AIS signal are performed in the rough sea surface. The results contribute to the high-accuracy propagation delay measurement of AIS signals spreading over the rough sea surface as, well as providing a reference for reliable communication link design in marine engineering for Very High Frequency (VHF) signals. PMID:29462995

Optimizing surface characteristics for cell adhesion and proliferation on titanium plasma spray coatings on polyetheretherketone.

PubMed

Yoon, Byung Jo Victor; Xavier, Fred; Walker, Brendon R; Grinberg, Samuel; Cammisa, Frank P; Abjornson, Celeste

2016-10-01

Titanium plasma spray coating on polyetheretherketone (PEEK) is a recent innovation to interbody spacer technology. The inherent hydrophobic properties of standard, uncoated PEEK implants can hamper cell attachment and bone healing during fusion. The addition of titanium coating not only offers initial stability due to increased surface roughness but also long-term stability due to bony ongrowth created from osteoconductive microenvironment on the device surface. The previously established hydrophilic and osteophilic properties of commercially pure titanium (CPTi) can potentially provide an ideal environment promoting cell attachment and bony ongrowth when applied at the end plate level of the fusion site. Because the surface material composition and topography is what seems to directly affect cell adhesion, it is important to determine the ideal titanium coating for the highest effectiveness. The purpose of the study is to determine whether there is an optimal surface roughness for the titanium coatings and whether different polishing methods have a greater effect than roughness or topography in mediating cell adhesion to the surface. The study was divided into two phases. In Phase 1, the effects of varying surface roughnesses on identical polishing method were compared. In Phase 2, the effect of varying polishing methods was compared on identical surface roughnesses. Coating thickness, porosity, and surface roughness were characterized using an optical microscope as per ASTM F 1854 standards. For both phases, PEEK coupons with plasma-sprayed CPTi were used, and human mesenchymal stem cells (hMSCs) at an initial density of 25,000 cells/cm 2 were seeded and cultured for 24 hours before fixation in 10% formalin. The cultured hMSCs were visualized by 4',6-diamidino-2-phenylindole (DAPI) staining, a fluorescent stain that binds to the DNA of living cells. Samples were imaged using an environmental scanning electron microscope (eSEM) (Carl Zeiss Microscopy, Thornwood, NY, USA) using a backscattered detector. Image analysis of the CPTi coatings showed uniform and rough surfaces. For Phase 1, roughness was evaluated as fine, medium, and coarse. The eSEM image analysis and cell counting by DAPI demonstrated that hMSCs have a tendency to form stronger adhesion and greater pseudopodia extensions on fine roughness surfaces. Individual hMSCs were seen forming cytoplasmic processes extending across the width of a pore. There was a 4- and 20-fold reduction in adhered hMSCs with an increase to medium and coarse roughnesses, respectively. For Phase 2, studied groups are (1) medium CPTi coating with zirconia polishing, (2) medium CPTi coating with CPTi polishing, and (3) fine CPTi coating with CPTi polishing. The eSEM image analysis and cell counting by DAPI demonstrated that hMSCs have a tendency to form stronger adhesion and greater pseudopodia extensions on Group 3 over the other two groups. There was a twofold reduction in adhered hMSCs on medium roughness relative to fine. No difference in cell adhesion was found between Groups 1 and 2. Individual hMSCs were seen forming cytoplasmic processes extending across the width of a pore. Previously, it was accepted without much scrutiny that surface coatings were beneficial. This study begins to discover that surface topography directly affects the potential for cells to adhere and proliferate and lead to greater surgical efficacy. Copyright © 2016 Elsevier Inc. All rights reserved.

10 CFR 2.1006 - Privilege.

Code of Federal Regulations, 2013 CFR

2013-01-01

... Licenses for the Receipt of High-Level Radioactive Waste at a Geologic Repository § 2.1006 Privilege. (a... Presiding Officer, must be provided in electronic form by the party, interested governmental participant, or... this section, circulated drafts not otherwise privileged shall be provided for electronic access...

10 CFR 2.1006 - Privilege.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Licenses for the Receipt of High-Level Radioactive Waste at a Geologic Repository § 2.1006 Privilege. (a... Presiding Officer, must be provided in electronic form by the party, interested governmental participant, or... this section, circulated drafts not otherwise privileged shall be provided for electronic access...

Best Practice Guidelines for Computer Technology in the Montessori Early Childhood Classroom.

ERIC Educational Resources Information Center

Montminy, Peter

1999-01-01

Presents a draft for a principle-centered position statement of a Montessori early childhood program in central Pennsylvania, on the pros and cons of computer use in a Montessori 3-6 classroom. Includes computer software rating form. (Author/KB)

Finite Element Analysis of Deep Wide-Flanged Pre-stressed Girders : Draft Final Report

DOT National Transportation Integrated Search

2011-06-01

Hundreds of prestressed concrete girders are used each year for building bridges in Wisconsin. : The prestress transfer from the prestressing strands to concrete takes place at the girder ends. : Characteristic cracks form in this end region during o...

Spatial characteristics of secondary flow in a turbulent boundary layer over longitudinal surface roughness

NASA Astrophysics Data System (ADS)

Hwang, Hyeon Gyu; Lee, Jae Hwa

2017-11-01

Direct numerical simulations of turbulent boundary layers (TBLs) over spanwise heterogeneous surface roughness are performed to investigate the characteristics of secondary flow. The longitudinal surface roughness, which features lateral change in bed elevation, is described by immersed boundary method. The Reynolds number based on the momentum thickness is varied in the range of Reθ = 300-900. As the TBLs over the roughness elements spatially develop in the streamwise direction, a secondary flow emerges in a form of counter-rotating vortex pair. As the spanwise spacing between the roughness elements and roughness width vary, it is shown that the size of the secondary flow is determined by the valley width between the roughness elements. In addition, the strength of the secondary flow is mostly affected by the spanwise distance between the cores of the secondary flow. Analysis of the Reynolds-averaged turbulent kinetic energy transport equation reveals that the energy redistribution terms in the TBLs over-the ridge type roughness play an important role to derive low-momentum pathways with upward motion over the roughness crest, contrary to the previous observation with the strip-type roughness. This research was supported by the National Research Foundation of Korea (NRF) funded by the Ministry of Education (NRF-2017R1D1A1A09000537) and the Ministry of Science, ICT & Future Planning (NRF-2017R1A5A1015311).

The role of connectedness in haptic object perception.

PubMed

Plaisier, Myrthe A; van Polanen, Vonne; Kappers, Astrid M L

2017-03-02

We can efficiently detect whether there is a rough object among a set of smooth objects using our sense of touch. We can also quickly determine the number of rough objects in our hand. In this study, we investigated whether the perceptual processing of rough and smooth objects is influenced if these objects are connected. In Experiment 1, participants were asked to identify whether there were exactly two rough target spheres among smooth distractor spheres, while we recorded their response times. The spheres were connected to form pairs: rough spheres were paired together and smooth spheres were paired together ('within pairs arrangement'), or a rough and a smooth sphere were connected ('between pairs arrangement'). Participants responded faster when the spheres in a pair were identical. In Experiment 2, we found that the advantage for within pairs arrangements was not driven by feature saliency. Overall our results show that haptic information is processed faster when targets were connected together compared to when targets were connected to distractors.

Super Water-Repellent Fractal Surfaces of a Photochromic Diarylethene Induced by UV Light

NASA Astrophysics Data System (ADS)

Izumi, Norikazu; Minami, Takayuki; Mayama, Hiroyuki; Takata, Atsushi; Nakamura, Shinichiro; Yokojima, Satoshi; Tsujii, Kaoru; Uchida, Kingo

2008-09-01

Photochromic diarylethene forms super water-repellent surfaces upon irradiation with UV light. Microfibril-like crystals grow on the solid diarylethene surface after UV irradiation, and the contact angle of water on the surface becomes larger with increasing surface roughness with time. The fractal analysis was made by the box-counting method for the rough surfaces. There are three regions in the roughness size having the fractal dimension of ca. 2.4 (size of roughness smaller than 5 µm), of ca. 2.2 (size of roughness between 5-40 µm), and of ca. 2.0 (size of roughness larger than 40 µm). The fractal dimension of ca. 2.4 was due to the fibril-like structures generated gradually by UV irradiation on diarylethene surfaces accompanied with an increase in the contact angle. The surface structure with larger fractal dimension mainly contributes to realizing the super water-repellency of the diarylethene surfaces. This mechanism of spontaneous formation of fractal surfaces is similar to that for triglyceride and alkylketene dimer waxes.

High quality draft genome sequence of the moderately halophilic bacterium Pontibacillus yanchengensis Y32(T) and comparison among Pontibacillus genomes.

PubMed

Huang, Jing; Qiao, Zi Xu; Tang, Jing Wei; Wang, Gejiao

2015-01-01

Pontibacillus yanchengensis Y32(T) is an aerobic, motile, Gram-positive, endospore-forming, and moderately halophilic bacterium isolated from a salt field. In this study, we describe the features of P. yanchengensis strain Y32(T) together with a comparison with other four Pontibacillus genomes. The 4,281,464 bp high-quality-draft genome of strain Y32(T) is arranged into 153 contigs containing 3,965 protein-coding genes and 77 RNA encoding genes. The genome of strain Y32(T) possesses many genes related to its halophilic character, flagellar assembly and chemotaxis to support its survival in a salt-rich environment.

LDV survey of cavitation and resonance effect on the precessing vortex rope dynamics in the draft tube of Francis turbines

NASA Astrophysics Data System (ADS)

Favrel, A.; Müller, A.; Landry, C.; Yamamoto, K.; Avellan, F.

2016-11-01

The large-scale penetration of the electrical grid by intermittent renewable energy sources requires a continuous operating range extension of hydropower plants. This causes the formation of unfavourable flow patterns in the draft tube of turbines and pump-turbines. At partial load operation, a precessing cavitation vortex rope is formed at the Francis turbine runner outlet, acting as an excitation source for the hydraulic system. In case of resonance, the resulting high-amplitude pressure pulsations can put at risk the stability of the machine and of the electrical grid to which it is connected. It is therefore crucial to understand and accurately simulate the underlying physical mechanisms in such conditions. However, the exact impact of cavitation and hydro-acoustic resonance on the flow velocity fluctuations in the draft tube remains to be established. The flow discharge pulsations expected to occur in the draft tube in resonance conditions have for instance never been verified experimentally. In this study, two-component Laser Doppler Velocimetry is used to investigate the axial and tangential velocity fluctuations at the runner outlet of a reduced scale physical model of a Francis turbine. The investigation is performed for a discharge equal to 64 % of the nominal value and three different pressure levels in the draft tube, including resonance and cavitation-free conditions. Based on the convective pressure fluctuations induced by the vortex precession, the periodical velocity fluctuations over one typical precession period are recovered by phase averaging. The impact of cavitation and hydro-acoustic resonance on both axial and tangential velocity fluctuations in terms of amplitude and phase shift is highlighted for the first time. It is shown that the occurrence of resonance does not have significant effects on the draft tube velocity fields, suggesting that the synchronous axial velocity fluctuations are surprisingly negligible compared to the velocity fluctuations induced by the vortex precession.

Rabies

Science.gov Websites

State Agencies | Online Services Forms Rules Ohio Public Health Advisory Board (OPHAB) Draft Pending Final Referenced Material Local Health Depts Find My Local Health Department What Do LHDs Do ? About Us About ODH ODH Locations News Reports Online Services What is Public Health? Employment

An Exposure Assessment of Polybrominated Diphenyl Ethers (External Review Draft)

EPA Science Inventory

The United States Environmental Protection Agency (U.S. EPA) has formed a working group comprised of individuals from several program offices including the Offices of Pesticides, Prevention, and Toxic Substances, the Office of Water, and the Office of Research and Development, Of...

Rayleigh's hypothesis and the geometrical optics limit.

PubMed

Elfouhaily, Tanos; Hahn, Thomas

2006-09-22

The Rayleigh hypothesis (RH) is often invoked in the theoretical and numerical treatment of rough surface scattering in order to decouple the analytical form of the scattered field. The hypothesis stipulates that the scattered field away from the surface can be extended down onto the rough surface even though it is formed by solely up-going waves. Traditionally this hypothesis is systematically used to derive the Volterra series under the small perturbation method which is equivalent to the low-frequency limit. In this Letter we demonstrate that the RH also carries the high-frequency or the geometrical optics limit, at least to first order. This finding has never been explicitly derived in the literature. Our result comforts the idea that the RH might be an exact solution under some constraints in the general case of random rough surfaces and not only in the case of small-slope deterministic periodic gratings.

Surface roughness and packaging tightness affect calcium lactate crystallization on Cheddar cheese.

PubMed

Rajbhandari, P; Kindstedt, P S

2014-01-01

Calcium lactate crystals that sometimes form on Cheddar cheese surfaces are a significant expense to manufacturers. Researchers have identified several postmanufacture conditions such as storage temperature and packaging tightness that contribute to crystal formation. Anecdotal reports suggest that physical characteristics at the cheese surface, such as roughness, cracks, and irregularities, may also affect crystallization. The aim of this study was to evaluate the combined effects of surface roughness and packaging tightness on crystal formation in smoked Cheddar cheese. Four 20-mm-thick cross-section slices were cut perpendicular to the long axis of a retail block (~300g) of smoked Cheddar cheese using a wire cutting device. One cut surface of each slice was lightly etched with a cheese grater to create a rough, grooved surface; the opposite cut surface was left undisturbed (smooth). The 4 slices were vacuum packaged at 1, 10, 50, and 90kPa (very tight, moderately tight, loose, very loose, respectively) and stored at 1°C. Digital images were taken at 1, 4, and 8 wk following the first appearance of crystals. The area occupied by crystals and number of discrete crystal regions (DCR) were quantified by image analysis. The experiment was conducted in triplicate. Effects of storage time, packaging tightness, surface roughness, and their interactions were evaluated by repeated-measures ANOVA. Surface roughness, packaging tightness, storage time, and their 2-way interactions significantly affected crystal area and DCR number. Extremely heavy crystallization occurred on both rough and smooth surfaces when slices were packaged loosely or very loosely and on rough surfaces with moderately tight packaging. In contrast, the combination of rough surface plus very tight packaging resulted in dramatic decreases in crystal area and DCR number. The combination of smooth surface plus very tight packaging virtually eliminated crystal formation, presumably by eliminating available sites for nucleation. Cut-and-wrap operations may significantly influence the crystallization behavior of Cheddar cheeses that are saturated with respect to calcium lactate and thus predisposed to form crystals. Copyright © 2014 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Movements of a Sphere Moving Over Smooth and Rough Inclines

NASA Astrophysics Data System (ADS)

Jan, Chyan-Deng

1992-01-01

The steady movements of a sphere over a rough incline in air, and over smooth and rough inclines in a liquid were studied theoretically and experimentally. The principle of energy conservation was used to analyze the translation velocities, rolling resistances, and drag coefficients of a sphere moving over the inclines. The rolling resistance to the movement of a sphere from the rough incline was presumed to be caused by collisions and frictional slidings. A varnished wooden board was placed on the bottom of an experimental tilting flume to form a smooth incline and a layer of spheres identical to the sphere moving over them was placed on the smooth wooden board to form a rough incline. Spheres used in the experiments were glass spheres, steel spheres, and golf balls. Experiments show that a sphere moving over a rough incline with negligible fluid drag in air can reach a constant translation velocity. This constant velocity was found to be proportional to the bed inclination (between 11 ^circ and 21^circ) and the square root of the sphere's diameter, but seemingly independent of the sphere's specific gravity. Two empirical coefficients in the theoretical expression of the sphere's translation velocity were determined by experiments. The collision and friction parts of the shear stress exerted on the interface between the moving sphere and rough incline were determined. The ratio of collision to friction parts appears to increase with increase in the bed inclination. These two parts seem to be of the same order of magnitude. The rolling resistances and the relations between the drag coefficient and Reynolds number for a sphere moving over smooth and rough inclines in a liquid, such as water or salad oil, were determined by a regression analysis based on experimental data. It was found that the drag coefficient for a sphere over the rough incline is larger than that for a sphere over the smooth incline, and both of which are much larger than that for a sphere in free fall. The relative magnitudes of the shear stresses due to drag, collision, and friction were also determined in terms of the Reynolds number.

Flow transition with 2-D roughness elements in a 3-D channel

NASA Technical Reports Server (NTRS)

Liu, Zhining; Liu, Chaoquin; Mccormick, Stephen F.

1993-01-01

We develop a new numerical approach to study the spatially evolving instability of the streamwise dominant flow in the presence of roughness elements. The difficulty in handling the flow over the boundary surface with general geometry is removed by using a new conservative form of the governing equations and an analytical mapping. The numerical scheme uses second-order backward Euler in time, fourth-order central differences in all three spatial directions, and boundary-fitted staggered grids. A three-dimensional channel with multiple two-dimensional-type roughness elements is employed as the test case. Fourier analysis is used to decompose different Fourier modes of the disturbance. The results show that surface roughness leads to transition at lower Reynolds number than for smooth channels.

Evaluation of surface roughness and polishing techniques for new ceramic materials.

PubMed

Campbell, S D

1989-05-01

The surface roughness of crown and bridge materials should be minimized to obtain optimal biocompatability. This study used scanning electron microscopy to evaluate the effect of polishing procedures on two all-ceramic crown materials (Dicor and Cerestore). The "as formed," unpolished specimens of both Dicor and Cerestore materials presented a rough surface. It was found that any attempt to polish the Cerestore coping material resulted in an extremely rough surface. Finishing of the Dicor ceramic resulted in a smoother but pitted surface. Polishing of both ceramic materials resulted in a surface that was rougher than the glazed metal ceramic controls. The smoothest finish was obtained when the glazed veneer (Cerestore) and shading porcelain (Dicor) were applied to the all-ceramic materials.

Pressure Distribution in a Squeeze Film Spherical Bearing with Rough Surfaces Lubricated by an Ellis Fluid

NASA Astrophysics Data System (ADS)

Jurczak, P.; Falicki, J.

2016-08-01

In this paper, the solution to a problem of pressure distribution in a curvilinear squeeze film spherical bearing is considered. The equations of motion of an Ellis pseudo-plastic fluid are presented. Using Christensen's stochastic model of rough surfaces, different forms of Reynolds equation for various types of surface roughness pattern are obtained. The analytical solutions of these equations for the cases of externally pressurized bearing and squeeze film bearing are presented. Analytical solutions for the film pressure are found for the longitudinal and circumferential roughness patterns. As a result the formulae expressing pressure distribution in the clearance of bearing lubricated by an Ellis fluid was obtained. The numerical considerations for a spherical bearing are given in detail.

Effects of surface roughness, MHD and couple stress on squeeze film characteristics between curved circular plates

NASA Astrophysics Data System (ADS)

Hanumagowda, B. N.; Salma, A.; Nagarajappa, C. S.

2018-04-01

The theoretical discussion is carried out for understanding the combined study of MHD, rough surface and couple-stress in the presence of applied magnetic field between two curved circular plates is present analysis. Modified Reynolds Equations accounting for rough surface using stochastic model of Christensen are mathematically formulated. The close form derivations for pressure, load-supporting capacity and response-film time are obtained. Our results shows that, there is an significant increase (decrease) for pressure, load-supporting capacity and squeeze film time due to the effect of azimuthal (radial) roughness parameter when compared to the Hanumagowda.et.al [14] and numerical data of load supporting capacity and response time are given in Table for engineering applications.

REVIEW OF THE NEGOTIATION OF THE MODEL PROTOCOL ADDITIONAL TO THE AGREEMENT(S) BETWEEN STATE(S) AND THE INTERNATIONAL ATOMIC ENERGY AGENCY FOR THE APPLICATION OF SAFEGUARDS, INFCIRC/540 (Corrected) VOLUME II/III IAEA COMMITTEE 24, Major Issues Underlying the Model Additional Protocol (1996-1997).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rosenthal, M.D.; Saum-Manning, L.; Houck, F.

Volume I of this Review traces the origins of the Model Additional Protocol. It covers the period from 1991, when events in Iraq triggered an intensive review of the safeguards system, until 1996, when the IAEA Board of Governors established Committee 24 to negotiate a new protocol to safeguards agreement. The period from 1991-1996 set the stage for this negotiation and shaped its outcome in important ways. During this 5-year period, many proposals for strengthening safeguards were suggested and reviewed. Some proposals were dropped, for example, the suggestion by the IAEA Secretariat to verify certain imports, and others were refined.more » A rough consensus was established about the directions in which the international community wanted to go, and this was reflected in the draft of an additional protocol that was submitted to the IAEA Board of Governors on May 6, 1996 in document GOV/2863, Strengthening the Effectiveness and Improving the Efficiency of the Safeguards System - Proposals For Implementation Under Complementary Legal Authority, A Report by the Director General. This document ended with a recommendation that, 'the Board, through an appropriate mechanism, finalize the required legal instrument taking as a basis the draft protocol proposed by the Secretariat and the explanation of the measures contained in this document.'« less

Beach Monitoring

Science.gov Websites

State Agencies | Online Services Forms Rules Ohio Public Health Advisory Board (OPHAB) Draft Pending Final Referenced Material Local Health Depts Find My Local Health Department What Do LHDs Do ? About Us About ODH ODH Locations News Reports Online Services What is Public Health? Employment

Public Swimming Pools

Science.gov Websites

State Agencies | Online Services Forms Rules Ohio Public Health Advisory Board (OPHAB) Draft Pending Final Referenced Material Local Health Depts Find My Local Health Department What Do LHDs Do ? About Us About ODH ODH Locations News Reports Online Services What is Public Health? Employment

76 FR 61092 - Notice of Intent To Prepare a Supplement to the Draft Environmental Impact Statement for the...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-03

... (SEL) re: 1[micro]Pa\\2\\-sec. The USFWS and the DoN collaborated to form the Marbled Murrelet Science... Administrative/Construction Field Office, an Inert Storage building, a Rigging Shop, and a Refit Support Facility...

Estimation of surface soil moisture and roughness from multi-angular ASAR imagery in the Watershed Allied Telemetry Experimental Research (WATER)

NASA Astrophysics Data System (ADS)

Wang, S. G.; Li, X.; Han, X. J.; Jin, R.

2010-06-01

Radar remote sensing has demonstrated its applicability to the retrieval of basin-scale soil moisture. The mechanism of radar backscattering from soils is complicated and strongly influenced by surface roughness. Furthermore, retrieval of soil moisture using AIEM-like models is a classic example of the underdetermined problem due to a lack of credible known soil roughness distributions at a regional scale. Characterization of this roughness is therefore crucial for an accurate derivation of soil moisture based on backscattering models. This study aims to directly obtain surface roughness information along with soil moisture from multi-angular ASAR images. The method first used a semi-empirical relationship that connects the roughness slope (Zs) and the difference in backscattering coefficient (Δσ) from ASAR data in different incidence angles, in combination with an optimal calibration form consisting of two roughness parameters (the standard deviation of surface height and the correlation length), to estimate the roughness parameters. The deduced surface roughness was then used in the AIEM model for the retrieval of soil moisture. An evaluation of the proposed method was performed in a grassland site in the middle stream of the Heihe River Basin, where the Watershed Allied Telemetry Experimental Research (WATER) was taken place. It has demonstrated that the method is feasible to achieve reliable estimation of soil water content. The key challenge to surface soil moisture retrieval is the presence of vegetation cover, which significantly impacts the estimates of surface roughness and soil moisture.

Refining a taxonomy for guideline implementation: results of an exercise in abstract classification

PubMed Central

2013-01-01

Background To better understand the efficacy of various implementation strategies, improved methods for describing and classifying the nature of these strategies are urgently required. The aim of this study was to develop and pilot the feasibility of a taxonomy to classify the nature and content of implementation strategies. Methods A draft implementation taxonomy was developed based on the Cochrane Effective Practice and Organisation of Care (EPOC) data collection checklist. The draft taxonomy had four domains (professional, financial, organisational and regulatory) covering 49 distinct strategies. We piloted the draft taxonomy by using it to classify the implementation strategies described in the conference abstracts of the implementation stream of the 2010 Guideline International Network Conference. Five authors classified the strategies in each abstract individually. Final categorisation was then carried out in a face-to-face consensus meeting involving three authors. Results The implementation strategies described in 71 conference abstracts were classified. Approximately 15.5% of abstracts utilised strategies that could not be categorised using the draft taxonomy. Of those strategies that could be categorised, the majority were professionally focused (57%). A total of 41% of projects used only one implementation strategy, with 29% using two and 31% three or more. The three most commonly used strategies were changes in quality assurance, quality improvement and/or performance measurement systems, changes in information and communication technology, and distribution of guideline materials (via hard-copy, audio-visual and/or electronic means). Conclusions Further refinement of the draft taxonomy is required to provide hierarchical dimensions and granularity, particularly in the areas of patient-focused interventions, those concerned with audit and feedback and quality improvement, and electronic forms of implementation, including electronic decision support. PMID:23497520

Refining a taxonomy for guideline implementation: results of an exercise in abstract classification.

PubMed

Mazza, Danielle; Bairstow, Phillip; Buchan, Heather; Chakraborty, Samantha Paubrey; Van Hecke, Oliver; Grech, Cathy; Kunnamo, Ilkka

2013-03-15

To better understand the efficacy of various implementation strategies, improved methods for describing and classifying the nature of these strategies are urgently required. The aim of this study was to develop and pilot the feasibility of a taxonomy to classify the nature and content of implementation strategies. A draft implementation taxonomy was developed based on the Cochrane Effective Practice and Organisation of Care (EPOC) data collection checklist. The draft taxonomy had four domains (professional, financial, organisational and regulatory) covering 49 distinct strategies. We piloted the draft taxonomy by using it to classify the implementation strategies described in the conference abstracts of the implementation stream of the 2010 Guideline International Network Conference. Five authors classified the strategies in each abstract individually. Final categorisation was then carried out in a face-to-face consensus meeting involving three authors. The implementation strategies described in 71 conference abstracts were classified. Approximately 15.5% of abstracts utilised strategies that could not be categorised using the draft taxonomy. Of those strategies that could be categorised, the majority were professionally focused (57%). A total of 41% of projects used only one implementation strategy, with 29% using two and 31% three or more. The three most commonly used strategies were changes in quality assurance, quality improvement and/or performance measurement systems, changes in information and communication technology, and distribution of guideline materials (via hard-copy, audio-visual and/or electronic means). Further refinement of the draft taxonomy is required to provide hierarchical dimensions and granularity, particularly in the areas of patient-focused interventions, those concerned with audit and feedback and quality improvement, and electronic forms of implementation, including electronic decision support.

46 CFR 97.40-10 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Draft marks and draft indicating systems. 97.40-10... VESSELS OPERATIONS Markings on Vessels § 97.40-10 Draft marks and draft indicating systems. (a) All vessels must have draft marks plainly and legibly visible upon the stem and upon the sternpost or...

46 CFR 196.40-10 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 7 2012-10-01 2012-10-01 false Draft marks and draft indicating systems. 196.40-10... VESSELS OPERATIONS Markings on Vessels § 196.40-10 Draft marks and draft indicating systems. (a) All vessels must have draft marks plainly and legibly visible upon the stem and upon the sternpost or...

46 CFR 78.50-10 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 3 2013-10-01 2013-10-01 false Draft marks and draft indicating systems. 78.50-10... OPERATIONS Markings on Vessels § 78.50-10 Draft marks and draft indicating systems. (a) All vessels must have draft marks plainly and legibly visible upon the stem and upon the sternpost or rudderpost or any place...

46 CFR 97.40-10 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Draft marks and draft indicating systems. 97.40-10... VESSELS OPERATIONS Markings on Vessels § 97.40-10 Draft marks and draft indicating systems. (a) All vessels must have draft marks plainly and legibly visible upon the stem and upon the sternpost or...

46 CFR 97.40-10 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Draft marks and draft indicating systems. 97.40-10... VESSELS OPERATIONS Markings on Vessels § 97.40-10 Draft marks and draft indicating systems. (a) All vessels must have draft marks plainly and legibly visible upon the stem and upon the sternpost or...

46 CFR 196.40-10 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 7 2013-10-01 2013-10-01 false Draft marks and draft indicating systems. 196.40-10... VESSELS OPERATIONS Markings on Vessels § 196.40-10 Draft marks and draft indicating systems. (a) All vessels must have draft marks plainly and legibly visible upon the stem and upon the sternpost or...

46 CFR 97.40-10 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Draft marks and draft indicating systems. 97.40-10... VESSELS OPERATIONS Markings on Vessels § 97.40-10 Draft marks and draft indicating systems. (a) All vessels must have draft marks plainly and legibly visible upon the stem and upon the sternpost or...

46 CFR 196.40-10 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 7 2011-10-01 2011-10-01 false Draft marks and draft indicating systems. 196.40-10... VESSELS OPERATIONS Markings on Vessels § 196.40-10 Draft marks and draft indicating systems. (a) All vessels must have draft marks plainly and legibly visible upon the stem and upon the sternpost or...

46 CFR 78.50-10 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 3 2010-10-01 2010-10-01 false Draft marks and draft indicating systems. 78.50-10... OPERATIONS Markings on Vessels § 78.50-10 Draft marks and draft indicating systems. (a) All vessels must have draft marks plainly and legibly visible upon the stem and upon the sternpost or rudderpost or any place...

46 CFR 78.50-10 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 3 2014-10-01 2014-10-01 false Draft marks and draft indicating systems. 78.50-10... OPERATIONS Markings on Vessels § 78.50-10 Draft marks and draft indicating systems. (a) All vessels must have draft marks plainly and legibly visible upon the stem and upon the sternpost or rudderpost or any place...

46 CFR 78.50-10 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 3 2012-10-01 2012-10-01 false Draft marks and draft indicating systems. 78.50-10... OPERATIONS Markings on Vessels § 78.50-10 Draft marks and draft indicating systems. (a) All vessels must have draft marks plainly and legibly visible upon the stem and upon the sternpost or rudderpost or any place...

46 CFR 97.40-10 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Draft marks and draft indicating systems. 97.40-10... VESSELS OPERATIONS Markings on Vessels § 97.40-10 Draft marks and draft indicating systems. (a) All vessels must have draft marks plainly and legibly visible upon the stem and upon the sternpost or...

46 CFR 196.40-10 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Draft marks and draft indicating systems. 196.40-10... VESSELS OPERATIONS Markings on Vessels § 196.40-10 Draft marks and draft indicating systems. (a) All vessels must have draft marks plainly and legibly visible upon the stem and upon the sternpost or...

46 CFR 78.50-10 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 3 2011-10-01 2011-10-01 false Draft marks and draft indicating systems. 78.50-10... OPERATIONS Markings on Vessels § 78.50-10 Draft marks and draft indicating systems. (a) All vessels must have draft marks plainly and legibly visible upon the stem and upon the sternpost or rudderpost or any place...

46 CFR 196.40-10 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 7 2014-10-01 2014-10-01 false Draft marks and draft indicating systems. 196.40-10... VESSELS OPERATIONS Markings on Vessels § 196.40-10 Draft marks and draft indicating systems. (a) All vessels must have draft marks plainly and legibly visible upon the stem and upon the sternpost or...

The Improvement of the Closed Bounded Volume (CBV) Evaluation Methods to Compute a Feasible Rough Machining Area Based on Faceted Models

NASA Astrophysics Data System (ADS)

Hadi Sutrisno, Himawan; Kiswanto, Gandjar; Istiyanto, Jos

2017-06-01

The rough machining is aimed at shaping a workpiece towards to its final form. This process takes up a big proportion of the machining time due to the removal of the bulk material which may affect the total machining time. In certain models, the rough machining has limitations especially on certain surfaces such as turbine blade and impeller. CBV evaluation is one of the concepts which is used to detect of areas admissible in the process of machining. While in the previous research, CBV area detection used a pair of normal vectors, in this research, the writer simplified the process to detect CBV area with a slicing line for each point cloud formed. The simulation resulted in three steps used for this method and they are: 1. Triangulation from CAD design models, 2. Development of CC point from the point cloud, 3. The slicing line method which is used to evaluate each point cloud position (under CBV and outer CBV). The result of this evaluation method can be used as a tool for orientation set-up on each CC point position of feasible areas in rough machining.

Symmetric and asymmetric capillary bridges between a rough surface and a parallel surface.

PubMed

Wang, Yongxin; Michielsen, Stephen; Lee, Hoon Joo

2013-09-03

Although the formation of a capillary bridge between two parallel surfaces has been extensively studied, the majority of research has described only symmetric capillary bridges between two smooth surfaces. In this work, an instrument was built to form a capillary bridge by squeezing a liquid drop on one surface with another surface. An analytical solution that describes the shape of symmetric capillary bridges joining two smooth surfaces has been extended to bridges that are asymmetric about the midplane and to rough surfaces. The solution, given by elliptical integrals of the first and second kind, is consistent with a constant Laplace pressure over the entire surface and has been verified for water, Kaydol, and dodecane drops forming symmetric and asymmetric bridges between parallel smooth surfaces. This solution has been applied to asymmetric capillary bridges between a smooth surface and a rough fabric surface as well as symmetric bridges between two rough surfaces. These solutions have been experimentally verified, and good agreement has been found between predicted and experimental profiles for small drops where the effect of gravity is negligible. Finally, a protocol for determining the profile from the volume and height of the capillary bridge has been developed and experimentally verified.

46 CFR 32.05-1 - Draft marks and draft indicating systems-TB/ALL.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 1 2014-10-01 2014-10-01 false Draft marks and draft indicating systems-TB/ALL. 32.05-1..., MACHINERY, AND HULL REQUIREMENTS Markings § 32.05-1 Draft marks and draft indicating systems—TB/ALL. (a) All vessels must have draft marks plainly and legibly visible upon the stem and upon the sternpost or...

46 CFR 32.05-1 - Draft marks and draft indicating systems-TB/ALL.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 1 2011-10-01 2011-10-01 false Draft marks and draft indicating systems-TB/ALL. 32.05-1..., MACHINERY, AND HULL REQUIREMENTS Markings § 32.05-1 Draft marks and draft indicating systems—TB/ALL. (a) All vessels must have draft marks plainly and legibly visible upon the stem and upon the sternpost or...

46 CFR 32.05-1 - Draft marks and draft indicating systems-TB/ALL.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 1 2010-10-01 2010-10-01 false Draft marks and draft indicating systems-TB/ALL. 32.05-1..., MACHINERY, AND HULL REQUIREMENTS Markings § 32.05-1 Draft marks and draft indicating systems—TB/ALL. (a) All vessels must have draft marks plainly and legibly visible upon the stem and upon the sternpost or...

46 CFR 32.05-1 - Draft marks and draft indicating systems-TB/ALL.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 1 2013-10-01 2013-10-01 false Draft marks and draft indicating systems-TB/ALL. 32.05-1..., MACHINERY, AND HULL REQUIREMENTS Markings § 32.05-1 Draft marks and draft indicating systems—TB/ALL. (a) All vessels must have draft marks plainly and legibly visible upon the stem and upon the sternpost or...

46 CFR 32.05-1 - Draft marks and draft indicating systems-TB/ALL.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 1 2012-10-01 2012-10-01 false Draft marks and draft indicating systems-TB/ALL. 32.05-1..., MACHINERY, AND HULL REQUIREMENTS Markings § 32.05-1 Draft marks and draft indicating systems—TB/ALL. (a) All vessels must have draft marks plainly and legibly visible upon the stem and upon the sternpost or...

Dependence of toxicity of silver nanoparticles on Pseudomonas putida biofilm structure.

PubMed

Thuptimdang, Pumis; Limpiyakorn, Tawan; Khan, Eakalak

2017-12-01

Susceptibility of biofilms with different physical structures to silver nanoparticles (AgNPs) was studied. Biofilms of Pseudomonas putida KT2440 were formed in batch conditions under different carbon sources (glucose, glutamic acid, and citrate), glucose concentrations (5 and 50 mM), and incubation temperatures (25 and 30 °C). The biofilms were observed using confocal laser scanning microscopy for their physical characteristics (biomass amount, thickness, biomass volume, surface to volume ratio, and roughness coefficient). The biofilms forming under different growth conditions exhibited different physical structures. The biofilm thickness and the roughness coefficient were found negatively and positively correlated with the biofilm susceptibility to AgNPs, respectively. The effect of AgNPs on biofilms was low (1-log reduction of cell number) when the biofilms had high biomass amount, high thickness, high biomass volume, low surface to volume ratio, and low roughness coefficient. Furthermore, the extracellular polymeric substance (EPS) stripping process was applied to confirm the dependence of susceptibility to AgNPs on the structure of biofilm. After the EPS stripping process, the biofilms forming under different conditions showed reduction in thickness and biomass volume, and increases in surface to volume ratio and roughness coefficient, which led to more biofilm susceptibility to AgNPs. The results of this study suggest that controlling the growth conditions to alter the biofilm physical structure is a possible approach to reduce the impact of AgNPs on biofilms in engineered and natural systems. Copyright © 2017 Elsevier Ltd. All rights reserved.

Ohio Department of Health Home

Science.gov Websites

State Agencies | Online Services Forms Rules Ohio Public Health Advisory Board (OPHAB) Draft Pending Final Referenced Material Local Health Depts Find My Local Health Department What Do LHDs Do ? About Us About ODH ODH Locations News Reports Online Services What is Public Health? Employment

32 CFR 291.9 - For official use only (FOUO).

Code of Federal Regulations, 2011 CFR

2011-07-01

...) FREEDOM OF INFORMATION ACT PROGRAM DEFENSE NUCLEAR AGENCY (DNA) FREEDOM OF INFORMATION ACT PROGRAM § 291.9... authorized as an anemic form of classification to protect national security interests. See DNA Instruction... papers. Records, such as notes, working papers, and drafts retained as historical evidence of DNA actions...

32 CFR 291.9 - For official use only (FOUO).

Code of Federal Regulations, 2013 CFR

2013-07-01

...) FREEDOM OF INFORMATION ACT PROGRAM DEFENSE NUCLEAR AGENCY (DNA) FREEDOM OF INFORMATION ACT PROGRAM § 291.9... authorized as an anemic form of classification to protect national security interests. See DNA Instruction... papers. Records, such as notes, working papers, and drafts retained as historical evidence of DNA actions...

A PROGRAM FOR ARCHITECTURAL TECHNICIAN'S TRAINING.

ERIC Educational Resources Information Center

TERNSTROM, CLINTON C.; AND OTHERS

ARCHITECTURAL TECHNICIANS TRANSLATE DESIGN AND SYSTEMS SOLUTIONS INTO GRAPHIC AND WRITTEN FORM AND ASSIST IN RENDERING ARCHITECTURAL SERVICES. IN 1966, A STUDY GROUP FROM THE AMERICAN INSTITUTE OF ARCHITECTS FOUND THAT EXISTING 2-YEAR PROGRAMS WERE INADEQUATE, FALLING INTO ONE OF TWO CATEGORIES--(1) DRAFTING COURSES WHICH LACKED BREADTH AND FAILED…

48 CFR 1852.217-72 - Phased acquisition using progressive competition down-selection procedures.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Regulations System NATIONAL AERONAUTICS AND SPACE ADMINISTRATION CLAUSES AND FORMS SOLICITATION PROVISIONS AND... Phase 2 proposals, including the final evaluation criteria and factors, will be provided at that time... award. (g) The following draft Phase 2 evaluation factors are provided for your information. Please note...

76 FR 24924 - Agency Information Collection Activities: Proposed Collection; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-03

... use of automated collection techniques or other forms of information technology? The public may examine and have copied for a fee publicly available documents, including the draft supporting statement, at the NRC's Public Document Room, O1-F21, One White Flint North, 11555 Rockville Pike, Rockville...

Literacy and Community Pariticpation. Prepublication Draft.

ERIC Educational Resources Information Center

Peschke, Edith

Literacy experts in composition have examined the exclusionary forces of academic discourse, and have identified various forms of classroom power that result from the system of academic literacy. Little is understood about the power relations that function to relate and regulate the classroom. Largely a humanistic notion, literacy has been defined…

16 CFR 1500.43 - Method of test for flashpoint of volatile flammable materials by Tagliabue open-cup apparatus.

Code of Federal Regulations, 2012 CFR

2012-01-01

... inches in length, with a right-angle bend 1/2-inch from each end. This wire is placed snugly in holes... form a top when shield is open). The interior of the draft shield shall be painted a flat black...

16 CFR 1500.43 - Method of test for flashpoint of volatile flammable materials by Tagliabue open-cup apparatus.

Code of Federal Regulations, 2014 CFR

2014-01-01

... inches in length, with a right-angle bend 1/2-inch from each end. This wire is placed snugly in holes... form a top when shield is open). The interior of the draft shield shall be painted a flat black...

78 FR 51733 - Draft Report on Carcinogens Monographs for ortho-Toluidine and Pentachlorophenol and By-Products...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-21

... Monographs for ortho-Toluidine and Pentachlorophenol and By-Products of Its Synthesis; Availability of... candidate substance is defined as ``pentachlorophenol and by-products of its synthesis.'' During synthesis of pentachlorophenol, several additional chlorinated molecules are formed as by-products. In addition...

78 FR 27391 - Agency Forms Undergoing Paperwork Reduction Act Review

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-10

... Materials for the Division of Blood Disorders (0920-0915, Expired 01/31/2013)--Reinstatement--National... messages and materials, CDC will conduct formative focus groups with people with SCD across the country... the formative focus groups, CDC will develop and test draft messages. A total of 10 focus groups will...

Scale growth of structures in the turbulent boundary layer with a rod-roughened wall

NASA Astrophysics Data System (ADS)

Lee, Jin; Kim, Jung Hoon; Lee, Jae Hwa

2016-01-01

Direct numerical simulation of a turbulent boundary layer over a rod-roughened wall is performed with a long streamwise domain to examine the streamwise-scale growth mechanism of streamwise velocity fluctuating structures in the presence of two-dimensional (2-D) surface roughness. An instantaneous analysis shows that there is a slightly larger population of long structures with a small helix angle (spanwise inclinations relative to streamwise) and a large spanwise width over the rough-wall compared to that over a smooth-wall. Further inspection of time-evolving instantaneous fields clearly exhibits that adjacent long structures combine to form a longer structure through a spanwise merging process over the rough-wall; moreover, spanwise merging for streamwise scale growth is expected to occur frequently over the rough-wall due to the large spanwise scales generated by the 2-D roughness. Finally, we examine the influence of a large width and a small helix angle of the structures over the rough-wall with regard to spatial two-point correlation. The results show that these factors can increase the streamwise coherence of the structures in a statistical sense.

Addressing scale dependence in roughness and morphometric statistics derived from point cloud data.

NASA Astrophysics Data System (ADS)

Buscombe, D.; Wheaton, J. M.; Hensleigh, J.; Grams, P. E.; Welcker, C. W.; Anderson, K.; Kaplinski, M. A.

2015-12-01

The heights of natural surfaces can be measured with such spatial density that almost the entire spectrum of physical roughness scales can be characterized, down to the morphological form and grain scales. With an ability to measure 'microtopography' comes a demand for analytical/computational tools for spatially explicit statistical characterization of surface roughness. Detrended standard deviation of surface heights is a popular means to create continuous maps of roughness from point cloud data, using moving windows and reporting window-centered statistics of variations from a trend surface. If 'roughness' is the statistical variation in the distribution of relief of a surface, then 'texture' is the frequency of change and spatial arrangement of roughness. The variance in surface height as a function of frequency obeys a power law. In consequence, roughness is dependent on the window size through which it is examined, which has a number of potential disadvantages: 1) the choice of window size becomes crucial, and obstructs comparisons between data; 2) if windows are large relative to multiple roughness scales, it is harder to discriminate between those scales; 3) if roughness is not scaled by the texture length scale, information on the spacing and clustering of roughness `elements' can be lost; and 4) such practice is not amenable to models describing the scattering of light and sound from rough natural surfaces. We discuss the relationship between roughness and texture. Some useful parameters which scale vertical roughness to characteristic horizontal length scales are suggested, with examples of bathymetric point clouds obtained using multibeam from two contrasting riverbeds, namely those of the Colorado River in Grand Canyon, and the Snake River in Hells Canyon. Such work, aside from automated texture characterization and texture segmentation, roughness and grain size calculation, might also be useful for feature detection and classification from point clouds.

The effects of fine-scale substratum roughness on diatom community structure in estuarine biofilms.

PubMed

Sweat, L Holly; Johnson, Kevin B

2013-09-01

Benthic diatoms are a major component of biofilms that form on surfaces submerged in marine environments. Roughness of the underlying substratum affects the settlement of both diatoms and subsequent macrofouling colonizers. This study reports the effects of roughness on estuarine diatom communities established in situ in the Indian River Lagoon, FL, USA. Natural communities were established on acrylic panels with a range of surface roughnesses. Smoother substrata exhibited higher cell density, species richness, and diversity. Twenty-three of 58 species were found either exclusively or more abundantly on the smooth surfaces compared to one or both roughened treatments. The results suggest a greater ability of benthic diatoms to recruit and colonize smooth surfaces, which is probably explained by a higher degree of contact between the cells and the surface.

Drafting Fundamentals. Drafting Module 1. Instructor's Guide.

ERIC Educational Resources Information Center

Missouri Univ., Columbia. Instructional Materials Lab.

This Missouri Vocational Instruction Management System instructor's drafting guide has been keyed to the drafting competency profile developed by state industry and education professionals. The guide contains a cross-reference table of instructional materials. Ten units cover drafting fundamentals: (1) introduction to drafting; (2) general safety;…

Functional Drafting, Drafting--Intermediate: 9255.02.

ERIC Educational Resources Information Center

Dade County Public Schools, Miami, FL.

The course consists of six instructional blocks totaling 135 clock hours: (1) functional drafting, (2) threads and fasteners, (3) pictorial drawings, (4) introduction to electronic drafting, (5) introduction to piping drafting, and (6) Quinmester posttest. Mastery of skills indicated in Drafting-Basic--9255.01 is a prerequisite. In the functional…

76 FR 41808 - Draft Environmental Impact Statement and Draft Habitat Conservation Plan for Oncor Electric...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-15

...] Draft Environmental Impact Statement and Draft Habitat Conservation Plan for Oncor Electric Delivery..., announce the availability of the draft environmental impact statement and the draft Oncor Electric Delivery... Oncor Electric Delivery Company, LLC (Applicant; Oncor), and (2) That the Applicant has developed a...

A mixed-methods research approach to the review of competency standards for orthotist/prosthetists in Australia.

PubMed

Ash, Susan; O'Connor, Jackie; Anderson, Sarah; Ridgewell, Emily; Clarke, Leigh

2015-06-01

The requirement for an allied health workforce is expanding as the global burden of disease increases internationally. To safely meet the demand for an expanded workforce of orthotist/prosthetists in Australia, competency based standards, which are up-to-date and evidence-based, are required. The aims of this study were to determine the minimum level for entry into the orthotic/prosthetic profession; to develop entry level competency standards for the profession; and to validate the developed entry-level competency standards within the profession nationally, using an evidence-based approach. A mixed-methods research design was applied, using a three-step sequential exploratory design, where step 1 involved collecting and analyzing qualitative data from two focus groups; step 2 involved exploratory instrument development and testing, developing the draft competency standards; and step 3 involved quantitative data collection and analysis - a Delphi survey. In stage 1 (steps 1 and 2), the two focus groups - an expert and a recent graduate group of Australian orthotist/prosthetists - were led by an experienced facilitator, to identify gaps in the current competency standards and then to outline a key purpose, and work roles and tasks for the profession. The resulting domains and activities of the first draft of the competency standards were synthesized using thematic analysis. In stage 2 (step 3), the draft-competency standards were circulated to a purposive sample of the membership of the Australian Orthotic Prosthetic Association, using three rounds of Delphi survey. A project reference group of orthotist/prosthetists reviewed the results of both stages. In stage 1, the expert (n = 10) and the new graduate (n = 8) groups separately identified work roles and tasks, which formed the initial draft of the competency standards. Further drafts were refined and performance criteria added by the project reference group, resulting in the final draft-competency standards. In stage 2, the final draft-competency standards were circulated to 56 members (n = 44 final round) of the Association, who agreed on the key purpose, 6 domains, 18 activities, and 68 performance criteria of the final competency standards. This study outlines a rigorous and evidence-based mixed-methods approach for developing and endorsing professional competency standards, which is representative of the views of the profession of orthotist/prosthetists.

Wettability of Thin Silicate-Containing Hydroxyapatite Films Formed by RF-Magnetron Sputtering

NASA Astrophysics Data System (ADS)

Gorodzha, S. N.; Surmeneva, M. A.; Surmenev, R. A.; Gribennikov, M. V.; Pichugin, V. F.; Sharonova, A. A.; Pustovalova, A. A.; Prymack, O.; Epple, M.; Wittmar, A.; Ulbricht, M.; Gogolinskii, K. V.; Kravchuk, K. S.

2014-02-01

Using the methods of electron and atomic force microscopy, X-ray structural analysis and measurements of the wetting angle, the features of morphology, structure, contact angle and free surface energy of silicon-containing calcium-phosphate coatings formed on the substrates made from titanium VT1-0 and stainless steel 12Cr18Ni10Ti are investigated. It is shown that the coating - substrate system possesses bimodal roughness formed by the substrate microrelief and coating nanostructure, whose principal crystalline phase is represented by silicon-substituted hydroxiapatite with the size of the coherent scattering region (CSR) 18-26 nm. It is found out that the formation of a nanostructured coating on the surface of rough substrates makes them hydrophilic. The limiting angle of water wetting for the coatings formed on titanium and steel acquires the values in the following ranges: 90-92 and 101-104°, respectively, and decreases with time.

A Computer Model of Drafting Effects on Collective Behavior in Elite 10,000-m Runners.

PubMed

Trenchard, Hugh; Renfree, Andrew; Peters, Derek M

2017-03-01

Drafting in cycling influences collective behavior of pelotons. Although evidence for collective behavior in competitive running events exists, it is not clear if this results from energetic savings conferred by drafting. This study modeled the effects of drafting on behavior in elite 10,000-m runners. Using performance data from a men's elite 10,000-m track running event, computer simulations were constructed using Netlogo 5.1 to test the effects of 3 different drafting quantities on collective behavior: no drafting, drafting to 3 m behind with up to ~8% energy savings (a realistic running draft), and drafting up to 3 m behind with up to 38% energy savings (a realistic cycling draft). Three measures of collective behavior were analyzed in each condition: mean speed, mean group stretch (distance between first- and last-placed runner), and runner-convergence ratio (RCR), which represents the degree of drafting benefit obtained by the follower in a pair of coupled runners. Mean speeds were 6.32 ± 0.28, 5.57 ± 0.18, and 5.51 ± 0.13 m/s in the cycling-draft, runner-draft, and no-draft conditions, respectively (all P < .001). RCR was lower in the cycling-draft condition but did not differ between the other 2. Mean stretch did not differ between conditions. Collective behaviors observed in running events cannot be fully explained through energetic savings conferred by realistic drafting benefits. They may therefore result from other, possibly psychological, processes. The benefits or otherwise of engaging in such behavior are as yet unclear.

46 CFR 131.220 - Drafts.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Drafts. 131.220 Section 131.220 Shipping COAST GUARD... Drafts. (a) Each vessel must have the drafts of the vessel plainly and legibly marked upon the stem and... easy observance. The bottom of each mark must indicate the draft. (b) Each draft must be taken from the...

46 CFR 131.220 - Drafts.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Drafts. 131.220 Section 131.220 Shipping COAST GUARD... Drafts. (a) Each vessel must have the drafts of the vessel plainly and legibly marked upon the stem and... easy observance. The bottom of each mark must indicate the draft. (b) Each draft must be taken from the...

33 CFR 401.29 - Maximum draft.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 3 2012-07-01 2012-07-01 false Maximum draft. 401.29 Section 401... TRANSPORTATION SEAWAY REGULATIONS AND RULES Regulations Seaway Navigation § 401.29 Maximum draft. (a) The draft...) The draft of a vessel shall not, in any case, exceed 79.2 dm or the maximum permissible draft...

46 CFR 131.220 - Drafts.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Drafts. 131.220 Section 131.220 Shipping COAST GUARD... Drafts. (a) Each vessel must have the drafts of the vessel plainly and legibly marked upon the stem and... easy observance. The bottom of each mark must indicate the draft. (b) Each draft must be taken from the...

46 CFR 131.220 - Drafts.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Drafts. 131.220 Section 131.220 Shipping COAST GUARD... Drafts. (a) Each vessel must have the drafts of the vessel plainly and legibly marked upon the stem and... easy observance. The bottom of each mark must indicate the draft. (b) Each draft must be taken from the...

33 CFR 401.29 - Maximum draft.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 3 2011-07-01 2011-07-01 false Maximum draft. 401.29 Section 401... TRANSPORTATION SEAWAY REGULATIONS AND RULES Regulations Seaway Navigation § 401.29 Maximum draft. (a) The draft...) The draft of a vessel shall not, in any case, exceed 79.2 dm or the maximum permissible draft...

46 CFR 131.220 - Drafts.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Drafts. 131.220 Section 131.220 Shipping COAST GUARD... Drafts. (a) Each vessel must have the drafts of the vessel plainly and legibly marked upon the stem and... easy observance. The bottom of each mark must indicate the draft. (b) Each draft must be taken from the...

76 FR 57760 - Notice of Availability of Draft Resource Management Plan and Draft Environmental Impact Statement...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-16

... Availability of Draft Resource Management Plan and Draft Environmental Impact Statement for the Colorado River... prepared a Draft Resource Management Plan (RMP) and Draft Environmental Impact Statement (EIS) for the... alternative) seeks to allocate limited resources among competing human interests, land uses, and conservation...

33 CFR 401.29 - Maximum draft.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Maximum draft. 401.29 Section 401... TRANSPORTATION SEAWAY REGULATIONS AND RULES Regulations Seaway Navigation § 401.29 Maximum draft. (a) The draft...) The draft of a vessel shall not, in any case, exceed 79.2 dm or the maximum permissible draft...

76 FR 59732 - Draft Environmental Impact Statement and Draft Habitat Conservation Plan for Oncor Electric...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-27

...] Draft Environmental Impact Statement and Draft Habitat Conservation Plan for Oncor Electric Delivery... availability of the draft environmental impact statement (DEIS) and the draft Oncor Electric Delivery Company... announced that Oncor Electric Delivery Company, LLC, has applied under section 10(a)(1)(B) of the Endangered...

Sediment transport in the presence of large reef bottom roughness

USGS Publications Warehouse

Pomeroy, Andrew; Lowe, Ryan J.; Ghisalberti, Marco; Storlazzi, Curt; Symonds, Graham; Roelvink, Dano

2017-01-01

The presence of large bottom roughness, such as that formed by benthic organisms on coral reef flats, has important implications for the size, concentration, and transport of suspended sediment in coastal environments. A 3 week field study was conducted in approximately 1.5 m water depth on the reef flat at Ningaloo Reef, Western Australia, to quantify the cross-reef hydrodynamics and suspended sediment dynamics over the large bottom roughness (∼20–40 cm) at the site. A logarithmic mean current profile consistently developed above the height of the roughness; however, the flow was substantially reduced below the height of the roughness (canopy region). Shear velocities inferred from the logarithmic profile and Reynolds stresses measured at the top of the roughness, which are traditionally used in predictive sediment transport formulations, were similar but much larger than that required to suspend the relatively coarse sediment present at the bed. Importantly, these stresses did not represent the stresses imparted on the sediment measured in suspension and are therefore not relevant to the description of suspended sediment transport in systems with large bottom roughness. Estimates of the bed shear stresses that accounted for the reduced near-bed flow in the presence of large roughness vastly improved the relationship between the predicted and observed grain sizes that were in suspension. Thus, the impact of roughness, not only on the overlying flow but also on bed stresses, must be accounted for to accurately estimate suspended sediment transport in regions with large bottom roughness, a common feature of many shallow coastal ecosystems.

The evolution of fracture surface roughness and its dependence on slip

NASA Astrophysics Data System (ADS)

Wells, Olivia L.

Under effective compression, impingement of opposing rough surfaces of a fracture can force the walls of the fracture apart during slip. Therefore, a fracture's surface roughness exerts a primary control on the amount of dilation that can be sustained on a fracture since the opposing surfaces need to remain in contact. Previous work has attempted to characterize fracture surface roughness through topographic profiles and power spectral density analysis, but these metrics describing the geometry of a fracture's surface are often non-unique when used independently. However, when combined these metrics are affective at characterizing fracture surface roughness, as well as the mechanisms affecting changes in roughness with increasing slip, and therefore changes in dilation. These mechanisms include the influence of primary grains and pores on initial fracture roughness, the effect of linkage on locally increasing roughness, and asperity destruction that limits the heights of asperities and forms gouge. This analysis reveals four essential stages of dilation during the lifecycle of a natural fracture, whereas previous slip-dilation models do not adequately address the evolution of fracture surface roughness: (1) initial slip companied by small dilation is mediated by roughness controlled by the primary grain and pore dimensions; (2) rapid dilation during and immediately following fracture growth by linkage of formerly isolated fractures; (3) wear of the fracture surface and gouge formation that minimizes dilation; and (4) between slip events cementation that modifies the mineral constituents in the fracture. By identifying these fundamental mechanisms that influence fracture surface roughness, this new conceptual model relating dilation to slip has specific applications to Enhanced Geothermal Systems (EGS), which attempt to produce long-lived dilation in natural fractures by inducing slip.

Effect of laser absorption on picosecond laser ablation of Cr12MoV mold steel, 9Cr18 stainless steel and H13A cemented carbide

NASA Astrophysics Data System (ADS)

Wu, Baoye; Liu, Peng; Wang, Xizhao; Zhang, Fei; Deng, Leimin; Duan, Jun; Zeng, Xiaoyan

2018-05-01

Due to excellent properties, Cr12MoV mold steel, 9Cr18 stainless steel and H13A cemented carbide are widely used in industry. In this paper, the effect of absorption of laser light on ablation efficiency and roughness have been studied using a picosecond pulse Nd:YVO4 laser. The experimental results reveal that laser wavelength, original surface roughness and chemical composition play an important role in controlling ablation efficiency and roughness. Firstly, higher ablation efficiency with lower surface roughness is achieved on the ablation of 9Cr18 at 532, comparing with 1064 nm. Secondly, the ablation efficiency increases while the Ra of the ablated region decreases with the decrease of original surface roughness on ablation of Cr12MoV mold steel at 532 nm. Thirdly, the ablation efficiency of H13A cemented carbide is much higher than 9Cr18 stainless steel and Cr12MoV mold steel at 1064 nm. Scanning electron microscopy images reveals the formation of pores on the surface of 9Cr18 stainless steel and Cr12MoV mold steel at 532 nm while no pores are formed at 1064 nm. As to H13A cemented carbide, worm-like structure is formed at 1064 nm. The synergetic effects of the heat accumulation, plasma shielding and ablation threshold on laser ablation efficiency and machining quality were analyzed and discussed systematically in this paper.

Wetting properties of molecularly rough surfaces

DOE Office of Scientific and Technical Information (OSTI.GOV)

Svoboda, Martin; Lísal, Martin, E-mail: lisal@icpf.cas.cz; Department of Physics, Institute of Science, J. E. Purkinje University, 400 96 Ústí n. Lab.

2015-09-14

We employ molecular dynamics simulations to study the wettability of nanoscale rough surfaces in systems governed by Lennard-Jones (LJ) interactions. We consider both smooth and molecularly rough planar surfaces. Solid substrates are modeled as a static collection of LJ particles arranged in a face-centered cubic lattice with the (100) surface exposed to the LJ fluid. Molecularly rough solid surfaces are prepared by removing several strips of LJ atoms from the external layers of the substrate, i.e., forming parallel nanogrooves on the surface. We vary the solid-fluid interactions to investigate strongly and weakly wettable surfaces. We determine the wetting properties bymore » measuring the equilibrium droplet profiles that are in turn used to evaluate the contact angles. Macroscopic arguments, such as those leading to Wenzel’s law, suggest that surface roughness always amplifies the wetting properties of a lyophilic surface. However, our results indicate the opposite effect from roughness for microscopically corrugated surfaces, i.e., surface roughness deteriorates the substrate wettability. Adding the roughness to a strongly wettable surface shrinks the surface area wet with the liquid, and it either increases or only marginally affects the contact angle, depending on the degree of liquid adsorption into the nanogrooves. For a weakly wettable surface, the roughness changes the surface character from lyophilic to lyophobic due to a weakening of the solid-fluid interactions by the presence of the nanogrooves and the weaker adsorption of the liquid into the nanogrooves.« less

Effects of surface roughness on an adverse-pressure-gradient separating turbulent boundary layer

NASA Astrophysics Data System (ADS)

Wu, Wen; Piomelli, Ugo; Turbulence Simulation; Modelling Laboratory Team

2017-11-01

Separating turbulent boundary layers over smooth and rough flat plates are investigated by large-eddy simulations. A suction-blowing velocity distribution is imposed at the top boundary to produce an adverse-to-favourable pressure gradient and a closed separation bubble. Sandgrain roughness in the fully-rough regime is modelled by an immersed boundary method. In the rough-wall case, streamline detachment occurs earlier and the separation region is substantially larger due to the momentum deficit caused by the roughness. The adverse pressure gradient decreases the form drag and causes a thin reversed-flow region below the roughness crest, so that Cf = 0 does not coincide with the detachment of the flow from the surface. The wake regions behind roughness elements affect the intermittency of the near-wall flow, so that upstream of the detachment point the flow can be reversed half of the time, but its average is positive. The separated shear layer exhibits higher turbulent kinetic energy (TKE); the growth of the TKE there begins earlier relative to the separation point, and the peak TKE occurs close to the separation point. The momentum deficit caused by the roughness, again, plays a critical role in these changes. The authors acknowledge the support from Hydro-Québec and the NSERC Collaborative Research & Development program (CRDPJ 418786-11). The simulations were performed at CAC Queen't site. UP also thanks the support of Canada Research Chair Program.

Modeling interface shear behavior of granular materials using micro-polar continuum approach

NASA Astrophysics Data System (ADS)

Ebrahimian, Babak; Noorzad, Ali; Alsaleh, Mustafa I.

2018-01-01

Recently, the authors have focused on the shear behavior of interface between granular soil body and very rough surface of moving bounding structure. For this purpose, they have used finite element method and a micro-polar elasto-plastic continuum model. They have shown that the boundary conditions assumed along the interface have strong influences on the soil behavior. While in the previous studies, only very rough bounding interfaces have been taken into account, the present investigation focuses on the rough, medium rough and relatively smooth interfaces. In this regard, plane monotonic shearing of an infinite extended narrow granular soil layer is simulated under constant vertical pressure and free dilatancy. The soil layer is located between two parallel rigid boundaries of different surface roughness values. Particular attention is paid to the effect of surface roughness of top and bottom boundaries on the shear behavior of granular soil layer. It is shown that the interaction between roughness of bounding structure surface and the rotation resistance of bounding grains can be modeled in a reasonable manner through considered Cosserat boundary conditions. The influence of surface roughness is investigated on the soil shear strength mobilized along the interface as well as on the location and evolution of shear localization formed within the layer. The obtained numerical results have been qualitatively compared with experimental observations as well as DEM simulations, and acceptable agreement is shown.

Bacterial attachment on titanium surfaces is dependent on topography and chemical changes induced by nonthermal atmospheric pressure plasma.

PubMed

Jeong, Won-Seok; Kwon, Jae-Sung; Lee, Jung-Hwan; Uhm, Soo-Hyuk; Ha Choi, Eun; Kim, Kwang-Mahn

2017-07-26

Here, we investigated the antibacterial effects of chemical changes induced by nonthermal atmospheric pressure plasma (NTAPP) on smooth and rough Ti. The morphologies of smooth and rough surfaces of Ti were examined using scanning electron microscopy (SEM). Both Ti specimens were then treated for 10 min by NTAPP with nitrogen gas. The surface roughness, chemistry, and wettability were examined by optical profilometry, x-ray photoelectron spectroscopy, and water contact angle analysis, respectively. Bacterial attachment was measured by determining the number of colony forming units and by SEM analysis. The rough Ti showed irregular micropits, whereas smooth Ti had a relatively regular pattern on the surface. There were no differences in morphology between samples before and after NTAPP treatment. NTAPP treatment resulted in changes from hydrophobic to hydrophilic properties on rough and smooth Ti; rough Ti showed relatively higher hydrophilicity. Before NTAPP treatment, Streptococcus sanguinis (S. sanguinis) showed greater attachment on rough Ti, and after NTAPP treatment, there was a significant reduction in bacterial attachment. Moreover, the bacterial attachment rate was significantly lower on rough Ti, and the structure of S. sanguinis colonies were significantly changed on NTAPP-treated Ti. NTAPP treatment inhibited bacterial attachment surrounding titanium implants, regardless of surface topography. Therefore, NTAPP treatment on Ti is a next-generation tool for antibacterial applications in the orthopaedic and dental fields.

Effect of blade-surface-roughness on the pumping performance of a turbomolecular pump

NASA Astrophysics Data System (ADS)

Sawada, T.; Yabuki, M.; Sugiyama, W.; Watanabe, M.

2005-11-01

Turbomolecular pumps (TMPs) are widely used in the semiconductor and other thin film industries. Some semiconductor processes form corrosive gases such as HCl or HF as byproducts. The elements of a TMP are sometimes coated with ceramic (SiO2) film for the purpose of preventing corrosion of the TMP. The blades coated with SiO2 have relatively rough surfaces. The effect of the surface roughness of the blades on the pumping performance has been studied experimentally and theoretically. Experimental results for TMPs with two rotor disks and one stator disk show that the TMP coated with SiO2 film gives about 11% to 13% higher maximum-compression ratio than the noncoated TMP when the blade speed ratio is 0.47. The theory based on the conic peak/dimple-surface-roughness model that has been proposed by the authors explains the change in the compression ratio with the surface roughness shown in the experiment.

Influence of cutting data on surface quality when machining 17-4 PH stainless steel

NASA Astrophysics Data System (ADS)

Popovici, T. D.; Dijmărescu, M. R.

2017-08-01

The aim of the research presented in this paper is to analyse the cutting data influence upon surface quality for 17-4 PH stainless steel milling machining. The cutting regime parameters considered for the experiments were established using cutting regimes from experimental researches or from industrial conditions as basis, within the recommended ranges. The experimental program structure was determined by taking into account compatibility and orthogonality conditions, minimal use of material and labour. The machined surface roughness was determined by measuring the Ra roughness parameter, followed by surface profile registration in the form of graphics which were saved on a computer with MarSurf PS1Explorer software. Based on Ra roughness parameter, maximum values were extracted from these graphics and the influence charts of the cutting regime parameters upon surface roughness were traced using Microsoft Excel software. After a thorough analysis of the resulting data, relevant conclusions were drawn, presenting the interdependence between the surface roughness of the machined 17-4 PH samples and the cutting data variation.

Application of Box-Behnken Design and Response Surface Methodology for Surface Roughness Prediction Model of CP-Ti Powder Metallurgy Components Through WEDM

NASA Astrophysics Data System (ADS)

Das, Arunangsu; Sarkar, Susenjit; Karanjai, Malobika; Sutradhar, Goutam

2018-04-01

The present work was undertaken to investigate and characterize the machining parameters (such as surface roughness, etc.) of uni-axially pressed commercially pure titanium sintered powder metallurgy components. Powder was uni-axially pressed at designated pressure of 840 MPa to form cylindrical samples and the green compacts were sintered at 0.001 mbar for about 4 h with sintering temperature varying from 1350 to 1450 °C. The influence of the sintering temperature, pulse-on and pulse-off time at wire-EDM on the surface roughness of the preforms has been investigated thoroughly. Experiments were conducted under different machining parameters in a CNC operated wire-cut EDM. The surface roughness of the machined surface was measured and critically analysed. The optimum surface roughness was achieved under the conditions of 6 μs pulse-on time, 9 μs pulse-off time and at sintering temperature of 1450 °C.

Automatic draft reading based on image processing

NASA Astrophysics Data System (ADS)

Tsujii, Takahiro; Yoshida, Hiromi; Iiguni, Youji

2016-10-01

In marine transportation, a draft survey is a means to determine the quantity of bulk cargo. Automatic draft reading based on computer image processing has been proposed. However, the conventional draft mark segmentation may fail when the video sequence has many other regions than draft marks and a hull, and the estimated waterline is inherently higher than the true one. To solve these problems, we propose an automatic draft reading method that uses morphological operations to detect draft marks and estimate the waterline for every frame with Canny edge detection and a robust estimation. Moreover, we emulate surveyors' draft reading process for getting the understanding of a shipper and a receiver. In an experiment in a towing tank, the draft reading error of the proposed method was <1 cm, showing the advantage of the proposed method. It is also shown that accurate draft reading has been achieved in a real-world scene.

Bathymetric and oceanic controls on Abbot Ice Shelf thickness and stability

NASA Astrophysics Data System (ADS)

Cochran, J. R.; Jacobs, S. S.; Tinto, K. J.; Bell, R. E.

2014-05-01

Ice shelves play key roles in stabilizing Antarctica's ice sheets, maintaining its high albedo and returning freshwater to the Southern Ocean. Improved data sets of ice shelf draft and underlying bathymetry are important for assessing ocean-ice interactions and modeling ice response to climate change. The long, narrow Abbot Ice Shelf south of Thurston Island produces a large volume of meltwater, but is close to being in overall mass balance. Here we invert NASA Operation IceBridge (OIB) airborne gravity data over the Abbot region to obtain sub-ice bathymetry, and combine OIB elevation and ice thickness measurements to estimate ice draft. A series of asymmetric fault-bounded basins formed during rifting of Zealandia from Antarctica underlie the Abbot Ice Shelf west of 94° W and the Cosgrove Ice Shelf to the south. Sub-ice water column depths along OIB flight lines are sufficiently deep to allow warm deep and thermocline waters observed near the western Abbot ice front to circulate through much of the ice shelf cavity. An average ice shelf draft of ~200 m, 15% less than the Bedmap2 compilation, coincides with the summer transition between the ocean surface mixed layer and upper thermocline. Thick ice streams feeding the Abbot cross relatively stable grounding lines and are rapidly thinned by the warmest inflow. While the ice shelf is presently in equilibrium, the overall correspondence between draft distribution and thermocline depth indicates sensitivity to changes in characteristics of the ocean surface and deep waters.

The Brief Pain Inventory and its "pain at its worst in the last 24 hours" item: clinical trial endpoint considerations.

PubMed

Atkinson, Thomas M; Mendoza, Tito R; Sit, Laura; Passik, Steven; Scher, Howard I; Cleeland, Charles; Basch, Ethan

2010-03-01

In 2006, the United States Food and Drug Administration (FDA) released a draft Guidance for Industry on the use of patient-reported outcomes (PRO) Measures in Medical Product Development to Support Labeling Claims. This draft guidance outlines psychometric aspects that should be considered when designing a PRO measure, including conceptual framework, content validity, construct validity, reliability, and the ability to detect clinically meaningful score changes. When finalized, it may provide a blueprint for evaluations of PRO measures that can be considered by sponsors and investigators involved in PRO research and drug registration trials. In this review we examine the short form of the Brief Pain Inventory (BPI) and particularly the "pain at its worst in the last 24 hours" item in the context of the FDA draft guidance, to assess its utility in clinical trials that include pain as a PRO endpoint. After a systematic evaluation of the psychometric aspects of the BPI, we conclude that the BPI and its "pain at its worst in the last 24 hours" item generically satisfy most key recommendations outlined in the draft guidance for assessing a pain-reduction treatment effect. Nonetheless, when the BPI is being considered for assessment of pain endpoints in a registration trial, sponsors and investigators should consult with the appropriate FDA division early during research design to discuss whether there is sufficient precedent to use the instrument in the population of interest or whether additional evaluations of measurement properties are advisable.

Electronic hand-drafting and picture management system.

PubMed

Yang, Tsung-Han; Ku, Cheng-Yuan; Yen, David C; Hsieh, Wen-Huai

2012-08-01

The Department of Health of Executive Yuan in Taiwan (R.O.C.) is implementing a five-stage project entitled Electronic Medical Record (EMR) converting all health records from written to electronic form. Traditionally, physicians record patients' symptoms, related examinations, and suggested treatments on paper medical records. Currently when implementing the EMR, all text files and image files in the Hospital Information System (HIS) and Picture Archiving and Communication Systems (PACS) are kept separate. The current medical system environment is unable to combine text files, hand-drafted files, and photographs in the same system, so it is difficult to support physicians with the recording of medical data. Furthermore, in surgical and other related departments, physicians need immediate access to medical records in order to understand the details of a patient's condition. In order to address these problems, the Department of Health has implemented an EMR project, with the primary goal of building an electronic hand-drafting and picture management system (HDP system) that can be used by medical personnel to record medical information in a convenient way. This system can simultaneously edit text files, hand-drafted files, and image files and then integrate these data into Portable Document Format (PDF) files. In addition, the output is designed to fit a variety of formats in order to meet various laws and regulations. By combining the HDP system with HIS and PACS, the applicability can be enhanced to fit various scenarios and can assist the medical industry in moving into the final phase of EMR.

Characterization on White Etching Layer Formed During Ceramic Milling of Inconel 718

NASA Astrophysics Data System (ADS)

Kruk, A.; Wusatowska-Sarnek, A. M.; Ziętara, M.; Jemielniak, K.; Siemiątkowski, Z.; Czyrska-Filemonowicz, A.

2018-03-01

A comprehensive characterization of the near surface formed during the interrupted high-speed dry ceramic milling of IN718 was performed using light imaging, SEM/EDX, TEM and nano-hardness methods. It was found out that even an initial cut by a fresh tool creates a sub-surface alteration roughly 20 µm deep. The depth of altered sub-surface progressively changed to a roughly 40 µm when the tool reached an approximately half of its life, and almost 60 µm at the tool's end of the life. In the last two cases, the visible WEL (utilizing a light microscope) of the thickness roughly 6 and 15 µm was created, respectively. The outermost layer of the deformed subsurface was found to be for all three cases approximately 1.5 µm thick and composed of dynamically recrystallized γ phase grains with the average diameter of approximately 150 nm. This layer was free of δ phase and γ' or γ″ precipitates. It was followed by a plastically deformed zone.

Structural properties 3,16-bis triisopropylsilylethynyl (pentacene) (TIPS-pentacene) thin films onto organic dielectric layer using slide coating method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rusnan, Fara Naila; Mohamad, Khairul Anuar; Seria, Dzul Fahmi Mohd Husin

3,16-bis triisopropylsilylethynyl (Pentacene) (TIPS-Pentacene) compactable interface property is important in order to have a good arrangement of molecular structure. Comparison for TIPS-Pentacene deposited between two different surface layers conducted. 0.1wt% TIPS-Pentacene diluted in chloroform were deposited onto poly(methylmeaclyrate) (PMMA) layered transparent substrates using slide coating method. X-ray diffraction (XRD) used to determine crystallinity of thin films. Series of (00l) diffraction peaks obtained with sharp first peaks (001) for TIPS-Pentacene deposited onto PMMA layer at 5.35° and separation of 16.3 Å. Morphology and surface roughness were carried out using scanning electron microscope (SEM) and surface profilemeter LS500, respectively.TIPS-Pentacene deposited onto PMMAmore » layer formed needled-like-shape grains with 10.26 nm surface roughness. These properties were related as thin film formed and its surface roughness plays important role towards good mobility devices.« less

Analytical skin friction and heat transfer formula for compressible internal flows

NASA Technical Reports Server (NTRS)

Dechant, Lawrence J.; Tattar, Marc J.

1994-01-01

An analytic, closed-form friction formula for turbulent, internal, compressible, fully developed flow was derived by extending the incompressible law-of-the-wall relation to compressible cases. The model is capable of analyzing heat transfer as a function of constant surface temperatures and surface roughness as well as analyzing adiabatic conditions. The formula reduces to Prandtl's law of friction for adiabatic, smooth, axisymmetric flow. In addition, the formula reduces to the Colebrook equation for incompressible, adiabatic, axisymmetric flow with various roughnesses. Comparisons with available experiments show that the model averages roughly 12.5 percent error for adiabatic flow and 18.5 percent error for flow involving heat transfer.

Drafting: Current Trends and Future Practices

ERIC Educational Resources Information Center

Jensen, C.

1976-01-01

Various research findings are reported on drafting trends which the author feels should be incorporated into teaching drafting: (1) true position and geometric tolerancing, (2) decimal and metric dimensioning, (3) functional drafting, (4) automated drafting, and (5) drawing reproductions. (BP)

Mississippi Curriculum Framework for Drafting and Design Technology (Program CIP: 48.0102--Architectural Drafting Technology) (Program CIP: 48.0101--General Drafting). Postsecondary Programs.

ERIC Educational Resources Information Center

Mississippi Research and Curriculum Unit for Vocational and Technical Education, State College.

This document, which is intended for use by community and junior colleges throughout Mississippi, contains curriculum frameworks for the two course sequences of the state's postsecondary-level drafting and design technology program: architectural drafting technology and drafting and design technology. Presented first are a program description and…

8 CFR 103.7 - Fees.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., remittance may be made by bank international money order or foreign draft drawn on a financial institution in... petition for school certification—$1,700, plus a site visit fee of $655 for each location listed on the..., mutilated, or destroyed, or for a change in name—$290. Form I-94.For issuance of Arrival/Departure Record at...

The Purpose, Structure and Limitations of the Electoral College

ERIC Educational Resources Information Center

Webster, Gerald R.

2016-01-01

The U.S. Constitution was drafted in Philadelphia from late May to mid-September 1787. The fifty-five delegates to the Constitutional Convention gathered to revise the Articles of Confederation but soon decided to write an entirely new document. These "Framers" were committed to forming a representative democracy, but their largely…

Work-Based Learning: A Resource Guide for Change. Test Draft.

ERIC Educational Resources Information Center

Hudson River Center for Program Development, Glenmont, NY.

This resource guide is intended to provide New York schools, business/industry, and others with resources to develop work-based learning strategies and components. Section 1 examines the scope, foundation, categories, and operation of work-based learning. Section 2 presents detailed information about the following forms of work-based learning:…

78 FR 14587 - Kelley-McDonough Low-Effect Habitat Conservation Plan for the Morro Shoulderband Snail, Community...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-06

...] Kelley-McDonough Low-Effect Habitat Conservation Plan for the Morro Shoulderband Snail, Community of Los... that includes the Kelley-McDonough Low-Effect Habitat Conservation Plan for the Morro Shoulderband... plan, draft environmental action statement and low-effect screening form, and related documents on the...

West Virginia Department of Transportation (WVDOT) hosted a peer exchange from October 19 \\0x2010 October 22, 2010.

DOT National Transportation Integrated Search

2010-10-01

The expressed objectives of the Peer Exchange were to discuss : 1) A draft revised policy manual for the RSS Section that in its final form is clear, concise, : and a standalone document. : 2) Strengths and weaknesses of the outlined policies. : 3...

75 FR 37483 - Request for Comments on the Draft Policy Statement on the Protection of Cesium-137 Chloride...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-29

... instruments for end users. This network of facilities ensures that every radiation detection instrument that... associated test-and-evaluation protocols for radiation detection, instrumentation, and personal dosimetry... intrusion. The NRC supports efforts to develop alternate forms of Cs-137 that would reduce the security...

77 FR 20030 - Draft Guidance for Industry: Reporting Harmful and Potentially Harmful Constituents in Tobacco...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-03

... products for consumer use--cigarettes, smokeless tobacco, and roll-your-own tobacco--and not with respect...: Cigarette smoke, smokeless tobacco products, and roll-your- own tobacco and cigarette filler. To facilitate... for cigarette smoke and filler, smokeless tobacco, and roll-your-own tobacco. FDA has created forms to...

75 FR 71789 - Reports, Forms, and Record keeping Requirements

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-24

...\\ NHTSA is proposing a multi-phased consumer research project and is currently requesting comment on the first phase of that research, which will consist of qualitative focus group market research and tire... already been sought on and a public meeting has already been held on a draft research plan for the...

Asian American Middleman Minority Theory. The Constructional Framework of an American Myth. Draft.

ERIC Educational Resources Information Center

Wong, Eugene Franklin

This paper questions the applicability of middleman minority theory to Chinese and Japanese Americans. The constructional elements of the theory, in its American form, are analyzed in the context of Chinese and Japanese American economic, social, and political conditions. The ethnic group triad (elite-middleman minority-masses) is identified and…

75 FR 39535 - Agency Information Collection Activities: Proposed Collection: Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-09

... opportunity for public comment on proposed data collection projects (section 3506(c)(2)(A) of Title 44, United... more information on the proposed project or to obtain a copy of the data collection plans and draft... forms of information technology. Proposed Project: Bureau of Primary Health Care (BPHC) Uniform Data...

Learning and Individual Differences: Process, Trait, and Content Determinants.

ERIC Educational Resources Information Center

Ackerman, Phillip L.; Kyllonen, Patrick C.; Roberts, Richard D.

In preparation for a conference on learning and individual differences, the invited authors prepared chapters, which were distributed in draft form. Presentations were followed by discussions, which were recorded, and then edited for this volume, so that the discussion transcript follows each paper. The chapters in part 1, General Background and…

High-quality permanent draft genome sequence of Rhizobium sullae strain WSM1592; a Hedysarum coronarium microsymbiont from Sassari, Italy

DOE PAGES

Yates, Ron; Howieson, John; De Meyer, Sofie E.; ...

2015-07-24

Rhizobium sullae strain WSM1592 is an aerobic, Gram-negative, non-spore-forming rod that was isolated from an effective nitrogen (N2) fixing root nodule formed on the short-lived perennial legume Hedysarum coronarium (also known as Sulla coronaria or Sulla). WSM1592 was isolated from a nodule recovered from H. coronarium roots located in Ottava, bordering Sassari, Sardinia in 1995. WSM1592 is highly effective at fixing nitrogen with H. coronarium, and is currently the commercial Sulla inoculant strain in Australia. Here we describe the features of R. sullae strain WSM1592, together with genome sequence information and its annotation. The 7,530,820 bp high-quality permanent draft genomemore » is arranged into 118 scaffolds of 118 contigs containing 7.453 protein-coding genes and 73 RNA-only encoding genes. In conclusion, this rhizobial genome is sequenced as part of the DOE Joint Genome Institute 2010 Genomic Encyclopedia for Bacteria and Archaea-Root Nodule Bacteria (GEBA-RNB) project.« less

Observations on the Growth of Roughness Elements Into Icing Feathers

NASA Technical Reports Server (NTRS)

Vargas, Mario; Tsao, Jen, Ching

2007-01-01

This work presents the results of an experiment conducted in the Icing Research Tunnel at NASA Glenn Research Center to understand the process by which icing feathers are formed in the initial stages of ice accretion formation on swept wings. Close-up photographic data were taken on an aluminum NACA 0012 swept wing tip airfoil. Two types of photographic data were obtained: time sequence close-up photographic data during the run and close-up photographic data of the ice accretion at the end of each run. Icing runs were conducted for short ice accretion times from 10 to 180 sec. The time sequence close-up photographic data was used to study the process frame by frame and to create movies of how the process developed. The movies confirmed that at glaze icing conditions in the attachment line area icing feathers develop from roughness elements. The close-up photographic data at the end of each run showed that roughness elements change into a pointed shape with an upstream facet and join on the side with other elements having the same change to form ridges with pointed shape and upstream facet. The ridges develop into feathers when the upstream facet grows away to form the stem of the feather. The ridges and their growth into feathers were observed to form the initial scallop tips present in complete scallops.

Three diameter-limit cuttings in West Virginia hardwoods a 5-year report

Treesearch

Russell J. Hutnik

1958-01-01

Mine timbers are a basic need of West Virginia's giant coal industry. The annual requirement of sawed mine timbers is roughly 250 million board feet. The mines also use a large volume of wood in rough form for props and lagging. Yet, compared to sawlogs and veneer logs, these mine timbers are low-value products. This means that they must be produced at low cost....

Automated Defect and Correlation Length Analysis of Block Copolymer Thin Film Nanopatterns

PubMed Central

Murphy, Jeffrey N.; Harris, Kenneth D.; Buriak, Jillian M.

2015-01-01

Line patterns produced by lamellae- and cylinder-forming block copolymer (BCP) thin films are of widespread interest for their potential to enable nanoscale patterning over large areas. In order for such patterning methods to effectively integrate with current technologies, the resulting patterns need to have low defect densities, and be produced in a short timescale. To understand whether a given polymer or annealing method might potentially meet such challenges, it is necessary to examine the evolution of defects. Unfortunately, few tools are readily available to researchers, particularly those engaged in the synthesis and design of new polymeric systems with the potential for patterning, to measure defects in such line patterns. To this end, we present an image analysis tool, which we have developed and made available, to measure the characteristics of such patterns in an automated fashion. Additionally we apply the tool to six cylinder-forming polystyrene-block-poly(2-vinylpyridine) polymers thermally annealed to explore the relationship between the size of each polymer and measured characteristics including line period, line-width, defect density, line-edge roughness (LER), line-width roughness (LWR), and correlation length. Finally, we explore the line-edge roughness, line-width roughness, defect density, and correlation length as a function of the image area sampled to determine each in a more rigorous fashion. PMID:26207990

Slip and accommodation coefficients from rarefaction and roughness in rotating microscale disk flows

NASA Astrophysics Data System (ADS)

Blanchard, Danny; Ligrani, Phil

2007-06-01

Accommodation coefficients are determined from experimental results and analysis based on the Navier-Stokes equations for rotation-induced flows in C-shaped fluid chamber passages formed between a rotating disk and a stationary surface. A first-order boundary condition is used to model the slip flow. The fluid chamber passage height ranges from 6.85to29.2μm to give Knudsen numbers from 0.0025 to 0.031 for air and helium. In all cases, roughness size is large compared to molecular mean free path. The unique method presented for deducing tangential momentum accommodation coefficients gives values with less uncertainty compared to procedures that rely on flows in stationary tubes and channels. When channel height is defined at the tops of the roughness elements, slip velocity magnitudes and associated accommodation coefficients are a result of rarefaction at solid-gas interfaces and shear at the gas-gas interfaces. With this arrangement, tangential accommodation coefficients obtained with this approach decrease, and slip velocity magnitudes increase, at a particular value of Knudsen number, as the level of surface roughness increases. At values of the mean roughness height greater than 500nm, accommodation coefficients then appear to be lower in air flows than in helium flows, when compared for a particular roughness configuration. When channel height is defined midway between the crests and troughs of the roughness elements, nondimensional pressure rise data show little or no dependence on the level of disk surface roughness and working fluid. With this arrangement, slip is largely independent of surface roughness magnitude and mostly due to rarefaction, provided the appropriate channel height is chosen to define the roughness height.

The use of player physical and technical skill match activity profiles to predict position in the Australian Football League draft.

PubMed

Woods, Carl T; Veale, James P; Collier, Neil; Robertson, Sam

2017-02-01

This study investigated the extent to which position in the Australian Football League (AFL) national draft is associated with individual game performance metrics. Physical/technical skill performance metrics were collated from all participants in the 2014 national under 18 (U18) championships (18 games) drafted into the AFL (n = 65; 17.8 ± 0.5 y); 232 observations. Players were subdivided into draft position (ranked 1-65) and then draft round (1-4). Here, earlier draft selection (i.e., closer to 1) reflects a more desirable player. Microtechnology and a commercial provider facilitated the quantification of individual game performance metrics (n = 16). Linear mixed models were fitted to data, modelling the extent to which draft position was associated with these metrics. Draft position in the first/second round was negatively associated with "contested possessions" and "contested marks", respectively. Physical performance metrics were positively associated with draft position in these rounds. Correlations weakened for the third/fourth rounds. Contested possessions/marks were associated with an earlier draft selection. Physical performance metrics were associated with a later draft selection. Recruiters change the type of U18 player they draft as the selection pool reduces. juniors with contested skill appear prioritised.

Comments from the Developmental Neurotoxicology Committee of the Japanese Teratology Society on the OECD Guideline for the Testing of Chemicals, Proposal for a New Guideline 426, Developmental Neurotoxicity Study, Draft Document (October 2006 version), and on the Draft Document of the Retrospective Performance Assessment of the Draft Test Guideline 426 on Developmental Neurotoxicity.

PubMed

Ema, Makoto; Fukui, Yoshihiro; Aoyama, Hiroaki; Fujiwara, Michio; Fuji, Junichiro; Inouye, Minoru; Iwase, Takayuki; Kihara, Takahide; Oi, Akihide; Otani, Hiroki; Shinomiya, Mitsuhiro; Sugioka, Kozo; Yamano, Tsunekazu; Yamashita, Keisuke H; Tanimura, Takashi

2007-06-01

In October 2006, a new revision of the draft guideline (OECD Guideline for the Testing of Chemicals, Proposal for a New Guideline 426. Developmental Neurotoxicity Study) and Draft Document of the Retrospective Performance Assessment (RPA) of the Draft Test Guideline 426 on Developmental Neurotoxicity were distributed following incorporation of the results of the Expert Consultation Meeting in Tokyo on May 24-26, 2005. The draft guideline consists of 50 paragraphs and an appendix with 102 references; and the draft RPA consists of 37 paragraphs with 109 references. National coordinators were requested to arrange for national expert reviews of these draft documents in their member countries. Members of the Developmental Neurotoxicology (DNT) Committee of the Japanese Teratology Society (JTS) reviewed, discussed, and commented on the draft Test Guideline Proposal. The DNT Committee of the JTS also commented on the draft document of the RPA. These comments were sent to the OECD Secretariat. The DNT Committee of the JTS expects the comments to be useful for the finalization of these draft documents.

Light emitting diode with high aspect ratio submicron roughness for light extraction and methods of forming

DOEpatents

Li, Ting [Ventura, CA

2011-04-26

The surface morphology of an LED light emitting surface is changed by applying a reactive ion etch (RIE) process to the light emitting surface. High aspect ratio, submicron roughness is formed on the light emitting surface by transferring a thin film metal hard-mask having submicron patterns to the surface prior to applying a reactive ion etch process. The submicron patterns in the metal hard-mask can be formed using a low cost, commercially available nano-patterned template which is transferred to the surface with the mask. After subsequently binding the mask to the surface, the template is removed and the RIE process is applied for time duration sufficient to change the morphology of the surface. The modified surface contains non-symmetric, submicron structures having high aspect ratio which increase the efficiency of the device.

Interpretation of aged sorption studies for pesticides and their use in European Union regulatory leaching assessments.

PubMed

Beulke, Sabine; van Beinum, Wendy; Suddaby, Laura

2015-04-01

First-tier regulatory exposure assessments for pesticides assume that pesticide sorption is instantaneous and fully reversible. In European Union (EU) regulatory guidance, an increase in sorption over time ("aged sorption") can be considered at the higher tier to refine predicted environmental concentrations in groundwater. Research commissioned by the UK Chemicals Regulation Directorate (CRD), funded by the Department for Environment Food & Rural Affairs (Defra), formed the basis of a draft regulatory guidance document proposing 1) a protocol on how to measure aged sorption of parent compounds in laboratory studies, 2) procedures to fit kinetic models to the experimental data, 3) criteria to test the reliability of the parameters, and 4) procedures for use of the parameters in the groundwater exposure assessment. The draft guidance was revised after feedback from stakeholders and testing of the guidance was performed against real data sets by an independent consultancy. The Chemicals Regulation Directorate submitted the revised document to the European Food Safety Authority (EFSA) for scrutiny. This article gives an overview of the draft guidance and explains the reasoning behind the recommendations made. 2015 Crown Copyright; Published 2015 SETAC.

Performance Evaluation of a Mechanical Draft Cross Flow Cooling Towers Employed in a Subtropical Region

NASA Astrophysics Data System (ADS)

Muthukumar, Palanisamy; Naik, Bukke Kiran; Goswami, Amarendra

2018-02-01

Mechanical draft cross flow cooling towers are generally used in a large-scale water cooled condenser based air-conditioning plants for removing heat from warm water which comes out from the condensing unit. During this process considerable amount of water in the form of drift (droplets) and evaporation is carried away along with the circulated air. In this paper, the performance evaluation of a standard cross flow induced draft cooling tower in terms of water loss, range, approach and cooling tower efficiency are presented. Extensive experimental studies have been carried out in three cooling towers employed in a water cooled condenser based 1200 TR A/C plant over a period of time. Daily variation of average water loss and cooling tower performance parameters have been reported for some selected days. The reported average water loss from three cooling towers is 4080 l/h and the estimated average water loss per TR per h is about 3.1 l at an average relative humidity (RH) of 83%. The water loss during peak hours (2 pm) is about 3.4 l/h-TR corresponding to 88% of RH and the corresponding efficiency of cooling towers varied between 25% and 45%.

Effect of practice and training in spatial skills on embedded figures scores of males and females.

PubMed

Johnson, S; Flinn, J M; Tyer, Z E

1979-06-01

The effect of practice and training in spatial skills on scores obtained by male and female students on the Embedded Figures Test was examined. Forms A and B were administered 6 wk. apart to three groups of subjects (ns = 28, 27, 27) enrolled in drafting, mathematics, and liberal arts courses. During the pretest-posttest period the drafting students received training while the other two groups served as controls. Analysis indicated (1) no initial sex difference in test scores; (2) liberal arts students differed significantly from drafting and mathematics students, but there was no significant difference between the last two groups; (3) all groups improved with practice; (4) women receiving training improved more than women who did not; (5) there was a trend toward women receiving spatial training scoring more poorly than males receiving training on the pretest, but there was no significant difference on the posttest. These results suggest that sex differences in embedded-figures scores found by many previous experimenters may have been associated with differences in prior experience in spatial skills and by a confounding of sex with area of academic study.

Technical Letter Report Development of Flaw Size Distribution Tables Including Effects of Flaw Depth Sizing Errors for Draft 10CFR 50.61a (Alternate PTS Rule) JCN-N6398, Task 4

DOE Office of Scientific and Technical Information (OSTI.GOV)

Simonen, Fredric A.; Gosselin, Stephen R.; Doctor, Steven R.

2013-04-22

This document describes a new method to determine whether the flaws in a particular reactor pressure vessel are consistent with the assumptions regarding the number and sizes of flaws used in the analyses that formed the technical justification basis for the new voluntary alternative Pressurized Thermal Shock (PTS) rule (Draft 10 CFR 50.61a). The new methodology addresses concerns regarding prior methodology because ASME Code Section XI examinations do not detect all fabrication flaws, they have higher detection performance for some flaw types, and there are flaw sizing errors always present (e.g., significant oversizing of small flaws and systematic under sizingmore » of larger flaws). The new methodology allows direct comparison of ASME Code Section XI examination results with values in the PTS draft rule Tables 2 and 3 in order to determine if the number and sizes of flaws detected by an ASME Code Section XI examination are consistent with those assumed in the probabilistic fracture mechanics calculations performed in support of the development of 10 CFR 50.61a.« less

The draft genome of blunt snout bream (Megalobrama amblycephala) reveals the development of intermuscular bone and adaptation to herbivorous diet

PubMed Central

Liu, Han; Chen, Chunhai; Gao, Zexia; Min, Jiumeng; Gu, Yongming; Jian, Jianbo; Jiang, Xiewu; Cai, Huimin; Ebersberger, Ingo; Xu, Meng; Zhang, Xinhui; Chen, Jianwei; Luo, Wei; Chen, Boxiang; Chen, Junhui; Liu, Hong; Li, Jiang; Lai, Ruifang; Bai, Mingzhou; Wei, Jin; Yi, Shaokui; Wang, Huanling; Cao, Xiaojuan; Zhou, Xiaoyun; Zhao, Yuhua; Wei, Kaijian; Yang, Ruibin; Liu, Bingnan; Zhao, Shancen; Fang, Xiaodong

2017-01-01

Abstract The blunt snout bream Megalobrama amblycephala is the economically most important cyprinid fish species. As an herbivore, it can be grown by eco-friendly and resource-conserving aquaculture. However, the large number of intermuscular bones in the trunk musculature is adverse to fish meat processing and consumption. As a first towards optimizing this aquatic livestock, we present a 1.116-Gb draft genome of M. amblycephala, with 779.54 Mb anchored on 24 linkage groups. Integrating spatiotemporal transcriptome analyses, we show that intermuscular bone is formed in the more basal teleosts by intramembranous ossification and may be involved in muscle contractibility and coordinating cellular events. Comparative analysis revealed that olfactory receptor genes, especially of the beta type, underwent an extensive expansion in herbivorous cyprinids, whereas the gene for the umami receptor T1R1 was specifically lost in M. amblycephala. The composition of gut microflora, which contributes to the herbivorous adaptation of M. amblycephala, was found to be similar to that of other herbivores. As a valuable resource for the improvement of M. amblycephala livestock, the draft genome sequence offers new insights into the development of intermuscular bone and herbivorous adaptation. PMID:28535200

10 CFR 51.86 - Distribution of draft environmental impact statement.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 2 2013-01-01 2013-01-01 false Distribution of draft environmental impact statement. 51...-Regulations Implementing Section 102(2) Draft Environmental Impact Statements-Rulemaking § 51.86 Distribution of draft environmental impact statement. Copies of the draft environmental impact statement and any...

10 CFR 51.86 - Distribution of draft environmental impact statement.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 2 2012-01-01 2012-01-01 false Distribution of draft environmental impact statement. 51...-Regulations Implementing Section 102(2) Draft Environmental Impact Statements-Rulemaking § 51.86 Distribution of draft environmental impact statement. Copies of the draft environmental impact statement and any...

10 CFR 51.81 - Distribution of draft environmental impact statement.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 2 2011-01-01 2011-01-01 false Distribution of draft environmental impact statement. 51...-Regulations Implementing Section 102(2) Draft Environmental Impact Statements-Materials Licenses § 51.81 Distribution of draft environmental impact statement. Copies of the draft environmental impact statement and...

10 CFR 51.81 - Distribution of draft environmental impact statement.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 2 2014-01-01 2014-01-01 false Distribution of draft environmental impact statement. 51...-Regulations Implementing Section 102(2) Draft Environmental Impact Statements-Materials Licenses § 51.81 Distribution of draft environmental impact statement. Copies of the draft environmental impact statement and...

10 CFR 51.81 - Distribution of draft environmental impact statement.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 2 2013-01-01 2013-01-01 false Distribution of draft environmental impact statement. 51...-Regulations Implementing Section 102(2) Draft Environmental Impact Statements-Materials Licenses § 51.81 Distribution of draft environmental impact statement. Copies of the draft environmental impact statement and...

10 CFR 51.81 - Distribution of draft environmental impact statement.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 2 2012-01-01 2012-01-01 false Distribution of draft environmental impact statement. 51...-Regulations Implementing Section 102(2) Draft Environmental Impact Statements-Materials Licenses § 51.81 Distribution of draft environmental impact statement. Copies of the draft environmental impact statement and...

10 CFR 51.86 - Distribution of draft environmental impact statement.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 2 2014-01-01 2014-01-01 false Distribution of draft environmental impact statement. 51...-Regulations Implementing Section 102(2) Draft Environmental Impact Statements-Rulemaking § 51.86 Distribution of draft environmental impact statement. Copies of the draft environmental impact statement and any...

10 CFR 51.86 - Distribution of draft environmental impact statement.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 2 2011-01-01 2011-01-01 false Distribution of draft environmental impact statement. 51...-Regulations Implementing Section 102(2) Draft Environmental Impact Statements-Rulemaking § 51.86 Distribution of draft environmental impact statement. Copies of the draft environmental impact statement and any...

10 CFR 51.86 - Distribution of draft environmental impact statement.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Distribution of draft environmental impact statement. 51...-Regulations Implementing Section 102(2) Draft Environmental Impact Statements-Rulemaking § 51.86 Distribution of draft environmental impact statement. Copies of the draft environmental impact statement and any...

10 CFR 51.81 - Distribution of draft environmental impact statement.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Distribution of draft environmental impact statement. 51...-Regulations Implementing Section 102(2) Draft Environmental Impact Statements-Materials Licenses § 51.81 Distribution of draft environmental impact statement. Copies of the draft environmental impact statement and...

76 FR 57759 - Notice of Availability of Draft Resource Management Plan and Draft Environmental Impact Statement...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-16

... Availability of Draft Resource Management Plan and Draft Environmental Impact Statement for the Kremmling Field... Management Act of 1976 (FLPMA), as amended, the Bureau of Land Management (BLM) has prepared a Draft Resource... alternatives for future [[Page 57760

Preparation and wettability examinations of transparent SiO2 binder-added MgF2 nanoparticle coatings covered with fluoro-alkyl silane self-assembled monolayer.

PubMed

Murata, Tsuyoshi; Hieda, Junko; Saito, Nagahiro; Takai, Osamu

2012-05-01

SiO2-added MgF2 nanoparticle coatings with various surface roughness properties were formed on fused silica-glass substrates from autoclaved sols prepared at 100-180 °C. To give it hydrophobicity, we treated the samples with fluoro-alkyl silane (FAS) vapor to form self-assembled monolayers on the nanoparticle coating and we examined the wettability of the samples. The samples preserved good transparency even after the FAS treatment. The wettability examination revealed that higher autoclave temperatures produced a larger average MgF2 nanoparticle particle size, a larger surface roughness, and a higher contact angle and the roll-off angle.

The Effect of Volumetric Porosity on Roughness Element Drag

NASA Astrophysics Data System (ADS)

Gillies, John; Nickling, William; Nikolich, George; Etyemezian, Vicken

2016-04-01

Much attention has been given to understanding how the porosity of two dimensional structures affects the drag force exerted by boundary-layer flow on these flow obstructions. Porous structures such as wind breaks and fences are typically used to control the sedimentation of sand and snow particles or create micro-habitats in their lee. Vegetation in drylands also exerts control on sediment transport by wind due to aerodynamic effects and interaction with particles in transport. Recent research has also demonstrated that large spatial arrays of solid three dimensional roughness elements can be used to reduce sand transport to specified targets for control of wind erosion through the effect of drag partitioning and interaction of the moving sand with the large (>0.3 m high) roughness elements, but porous elements may improve the effectiveness of this approach. A thorough understanding of the role porosity plays in affecting the drag force on three-dimensional forms is lacking. To provide basic understanding of the relationship between the porosity of roughness elements and the force of drag exerted on them by fluid flow, we undertook a wind tunnel study that systematically altered the porosity of roughness elements of defined geometry (cubes, rectangular cylinders, and round cylinders) and measured the associated change in the drag force on the elements under similar Reynolds number conditions. The elements tested were of four basic forms: 1) same sized cubes with tubes of known diameter milled through them creating three volumetric porosity values and increasing connectivity between the tubes, 2) cubes and rectangular cylinders constructed of brass screen that nested within each other, and 3) round cylinders constructed of brass screen that nested within each other. The two-dimensional porosity, defined as the ratio of total surface area of the empty space to the solid surface area of the side of the element presented to the fluid flow was conserved at 0.519 for the cubes and 0.525 for the mesh forms. Results from the study indicate that as volumetric porosity increases, the force of drag on an element increases although the 2-dimensional porosity remains unchanged for the case of the cube forms. The mesh forms show a similar result that with increasing number of internal forms present, drag increases, but the drag curves are different, suggesting the kind of porosity has an effect on drag. An important scaling parameter that controls drag on the cubes is the permeability (K) of the element, which is a function of the diameter of the tubes and the porosity. K seems to be of lesser importance for controlling drag on the mesh forms. We hypothesize that the drag force data do not universally collapse as a function of permeability due to Reynolds number dependency on flow conditions within the elements that can be laminar, transitional, or turbulent even though flow exterior to the forms is fully turbulent. For the mesh forms, the greatest effect on drag occurs with the addition of the first internal form with subsequent additions showing very little additional effect.

Computer Assisted Drafting (CNC) Drawings. Drafting Module 6. Instructor's Guide.

ERIC Educational Resources Information Center

Missouri Univ., Columbia. Instructional Materials Lab.

This Missouri Vocational Instruction Management System instructor's drafting guide has been keyed to the drafting competency profile developed by state industry and education professionals. This unit contains information on computer-assisted drafting drawings. The guide contains a cross-reference table of instructional materials and 20 worksheets.…

49 CFR 229.61 - Draft system.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 4 2014-10-01 2014-10-01 false Draft system. 229.61 Section 229.61 Transportation... TRANSPORTATION RAILROAD LOCOMOTIVE SAFETY STANDARDS Safety Requirements Draft System § 229.61 Draft system. (a) A... absorbed by friction devices or draft gears that exceeds one-half inches. (5) A broken or cracked coupler...

10 CFR 51.80 - Draft environmental impact statement-materials license.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 2 2013-01-01 2013-01-01 false Draft environmental impact statement-materials license. 51...-Regulations Implementing Section 102(2) Draft Environmental Impact Statements-Materials Licenses § 51.80 Draft environmental impact statement—materials license. (a) The NRC staff will either prepare a draft environmental...

49 CFR 230.92 - Draw gear and draft systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Draw gear and draft systems. 230.92 Section 230.92 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION... Tenders Draw Gear and Draft Systems § 230.92 Draw gear and draft systems. Couplers, draft gear and...

49 CFR 230.92 - Draw gear and draft systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 4 2014-10-01 2014-10-01 false Draw gear and draft systems. 230.92 Section 230.92 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION... Tenders Draw Gear and Draft Systems § 230.92 Draw gear and draft systems. Couplers, draft gear and...

10 CFR 51.80 - Draft environmental impact statement-materials license.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 2 2012-01-01 2012-01-01 false Draft environmental impact statement-materials license. 51...-Regulations Implementing Section 102(2) Draft Environmental Impact Statements-Materials Licenses § 51.80 Draft environmental impact statement—materials license. (a) The NRC staff will either prepare a draft environmental...

10 CFR 51.80 - Draft environmental impact statement-materials license.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 2 2011-01-01 2011-01-01 false Draft environmental impact statement-materials license. 51...-Regulations Implementing Section 102(2) Draft Environmental Impact Statements-Materials Licenses § 51.80 Draft environmental impact statement—materials license. (a) The NRC staff will either prepare a draft environmental...

49 CFR 229.61 - Draft system.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 4 2012-10-01 2012-10-01 false Draft system. 229.61 Section 229.61 Transportation... TRANSPORTATION RAILROAD LOCOMOTIVE SAFETY STANDARDS Safety Requirements Draft System § 229.61 Draft system. (a) A... absorbed by friction devices or draft gears that exceeds one-half inches. (5) A broken or cracked coupler...

49 CFR 230.92 - Draw gear and draft systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 4 2011-10-01 2011-10-01 false Draw gear and draft systems. 230.92 Section 230.92 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION... Tenders Draw Gear and Draft Systems § 230.92 Draw gear and draft systems. Couplers, draft gear and...

10 CFR 51.80 - Draft environmental impact statement-materials license.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 2 2014-01-01 2014-01-01 false Draft environmental impact statement-materials license. 51...-Regulations Implementing Section 102(2) Draft Environmental Impact Statements-Materials Licenses § 51.80 Draft environmental impact statement—materials license. (a) The NRC staff will either prepare a draft environmental...

49 CFR 230.92 - Draw gear and draft systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 4 2013-10-01 2013-10-01 false Draw gear and draft systems. 230.92 Section 230.92 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION... Tenders Draw Gear and Draft Systems § 230.92 Draw gear and draft systems. Couplers, draft gear and...

49 CFR 230.92 - Draw gear and draft systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 4 2012-10-01 2012-10-01 false Draw gear and draft systems. 230.92 Section 230.92 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION... Tenders Draw Gear and Draft Systems § 230.92 Draw gear and draft systems. Couplers, draft gear and...

49 CFR 229.61 - Draft system.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 4 2013-10-01 2013-10-01 false Draft system. 229.61 Section 229.61 Transportation... TRANSPORTATION RAILROAD LOCOMOTIVE SAFETY STANDARDS Safety Requirements Draft System § 229.61 Draft system. (a) A... absorbed by friction devices or draft gears that exceeds one-half inches. (5) A broken or cracked coupler...

77 FR 46518 - Draft Resource Management Plan/General Plan Draft Environmental Impact Statement/Revised Draft...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-03

... DEPARTMENT OF THE INTERIOR Bureau of Reclamation Draft Resource Management Plan/General Plan Draft... Recreation Area, Merced County, California AGENCY: Bureau of Reclamation, Interior. ACTION: Notice of... California Department of Parks and Recreation was given the responsibility to plan, design, construct...

IRIS Toxicological Review of Ammonia (Revised External Review Draft)

EPA Science Inventory

In August 2013, EPA submitted a revised draft IRIS assessment of ammonia to the agency's Science Advisory Board (SAB) and posted this draft on the IRIS website. EPA had previously released a draft of the assessment for public comment, held a public meeting about the draft, and ...

CURRENT PRACTICES OBSERVED IN DESIGN AND DRAFTING OCCUPATIONS.

ERIC Educational Resources Information Center

SQUIRES, CARL E.

DATA WHICH HAD SIGNIFICANCE FOR DESIGN AND DRAFTING CURRICULUMS WERE COLLECTED BY DIRECT OBSERVATION OF 21 DESIGN AND DRAFTING FACTORS WITHIN 16 SELECTED INDUSTRIAL COMPANIES EMPLOYING 869 DESIGNERS AND DRAFTSMEN. OBSERVATIONS COVERED (1) THE NUMBER OF DESIGN AND DRAFTING EMPLOYEES, (2) THE SYSTEM OF DRAFTING ROOM ORGANIZATION, (3) JOB…

10 CFR 51.80 - Draft environmental impact statement-materials license.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Draft environmental impact statement-materials license. 51...-Regulations Implementing Section 102(2) Draft Environmental Impact Statements-Materials Licenses § 51.80 Draft environmental impact statement—materials license. (a) The NRC staff will either prepare a draft environmental...

Rough-to-smooth transition of an equilibrium neutral constant stress layer

NASA Technical Reports Server (NTRS)

Logan, E., Jr.; Fichtl, G. H.

1975-01-01

Purpose of research on rough-to-smooth transition of an equilibrium neutral constant stress layer is to develop a model for low-level atmospheric flow over terrains of abruptly changing roughness, such as those occurring near the windward end of a landing strip, and to use the model to derive functions which define the extent of the region affected by the roughness change and allow adequate prediction of wind and shear stress profiles at all points within the region. A model consisting of two bounding logarithmic layers and an intermediate velocity defect layer is assumed, and dimensionless velocity and stress distribution functions which meet all boundary and matching conditions are hypothesized. The functions are used in an asymptotic form of the equation of motion to derive a relation which governs the growth of the internal boundary layer. The growth relation is used to predict variation of surface shear stress.

Determination and interpretation of the optical constants for solar cell materials

NASA Astrophysics Data System (ADS)

Fujiwara, Hiroyuki; Fujimoto, Shohei; Tamakoshi, Masato; Kato, Masato; Kadowaki, Hideyuki; Miyadera, Tetsuhiko; Tampo, Hitoshi; Chikamatsu, Masayuki; Shibata, Hajime

2017-11-01

Solar cell materials in thin film form often exhibit quite rough surface, which makes the accurate determination of the optical constants using spectroscopic ellipsometry (SE) quite difficult. In this study, we investigate the effect of the rough surface on the SE analysis and establish an analysis procedure, which is quite helpful for the correction of the underestimated roughness contribution. As examples, the roughness analyses for CuInSe2 and CH3NH3PbI3 hybrid-perovskite thin films are presented. Moreover, to interpret the dielectric functions of emerging solar cell materials, such as CH3NH3PbI3 and Cu2ZnSnSe4, the optical transition analyses are performed based on density functional theory (DFT). The excellent agreement observed between the experimental and DFT results allows the detailed assignment of the transition peaks, confirming the importance of DFT for revealing fundamental optical characteristics.

Cleaning of optical surfaces by capacitively coupled RF discharge plasma

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yadav, P. K., E-mail: praveenyadav@rrcat.gov.in; Rai, S. K.; Nayak, M.

2014-04-24

In this paper, we report cleaning of carbon capped molybdenum (Mo) thin film by in-house developed radio frequency (RF) plasma reactor, at different powers and exposure time. Carbon capped Mo films were exposed to oxygen plasma for different durations at three different power settings, at a constant pressure. After each exposure, the thickness of the carbon layer and the roughness of the film were determined by hard x-ray reflectivity measurements. It was observed that most of the carbon film got removed in first 15 minutes exposure. A high density layer formed on top of the Mo film was also observedmore » and it was noted that this layer cannot be removed by successive exposures at different powers. A significant improvement in interface roughness with a slight improvement in top film roughness was observed. The surface roughness of the exposed and unexposed samples was also confirmed by atomic force microscopy measurements.« less

Nanoscale roughness contact in a slider-disk interface.

PubMed

Hua, Wei; Liu, Bo; Yu, Shengkai; Zhou, Weidong

2009-07-15

The nanoscale roughness contact between molecularly smooth surfaces of a slider-disk interface in a hard disk drive is analyzed, and the lubricant behavior at very high shear rate is presented. A new contact model is developed to study the nanoscale roughness contact behavior by classifying various forms of contact into slider-lubricant contact, slider-disk elastic contact and plastic contact. The contact pressure and the contact probabilities of the three types of contact are investigated. The new contact model is employed to explain and provide insight to an interesting experimental result found in a thermal protrusion slider. The protrusion budget for head surfing in the lubricant, which is the ideal state for contact recording, is also discussed.

Fractional-dimensional Child-Langmuir law for a rough cathode

NASA Astrophysics Data System (ADS)

Zubair, M.; Ang, L. K.

2016-07-01

This work presents a self-consistent model of space charge limited current transport in a gap combined of free-space and fractional-dimensional space (Fα), where α is the fractional dimension in the range 0 < α ≤ 1. In this approach, a closed-form fractional-dimensional generalization of Child-Langmuir (CL) law is derived in classical regime which is then used to model the effect of cathode surface roughness in a vacuum diode by replacing the rough cathode with a smooth cathode placed in a layer of effective fractional-dimensional space. Smooth transition of CL law from the fractional-dimensional to integer-dimensional space is also demonstrated. The model has been validated by comparing results with an experiment.

Innovative potential of plasma technology

NASA Astrophysics Data System (ADS)

Budaev, V. P.

2017-11-01

The review summarizes recent experimental observations of materials exposed to extreme hot plasma loads in fusion devices and plasma facilities with high-temperature plasma. Plasma load on the material in such devices lead to the stochastic clustering and fractal growth of the surface on scales from tens of nanometers to hundreds of micrometers forming statistical self-similarity of the surface roughness with extremely high specific area. Statistical characteristics of hierarchical granularity and scale invariance of such materials surface qualitatively differ from the properties of the roughness of the ordinary Brownian surface which provides a potential of innovative plasma technologies for synthesis of new nanostructured materials with programmed roughness properties, for hypersonic technologies, for biotechnology and biomedical applications.

Managing the Drafting Process: Creating a New Model for the Workplace.

ERIC Educational Resources Information Center

Shwom, Barbara L.; Hirsch, Penny L.

1994-01-01

Discusses the development of a pragmatic model of the writing process in the workplace, focusing on the importance of "drafting" as part of that process. Discusses writers' attitudes about drafting and the structures of the workplace that drafting has to accommodate. Introduces a drafting model and discusses results of using this model…

76 FR 65722 - Notification of Two Public Teleconferences; Clean Air Scientific Advisory Committee

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-24

... EPA's Integrated Science Assessment for Lead (First External Review Draft, May 2011) and EPA's draft... Science Assessment for Lead (First External Review Draft, May 2011) should be directed to Dr. Ellen... Integrated Science Assessment for Lead (First External Review Draft, May 2011) and EPA's draft Near-Road NO 2...

46 CFR 151.03-35 - Limiting draft.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Limiting draft. 151.03-35 Section 151.03-35 Shipping... BULK LIQUID HAZARDOUS MATERIAL CARGOES Definitions § 151.03-35 Limiting draft. Maximum allowable draft to which a barge may be loaded. Limiting draft is a function of hull type and cargo specific gravity...

32 CFR 989.19 - Draft EIS.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 32 National Defense 6 2014-07-01 2014-07-01 false Draft EIS. 989.19 Section 989.19 National... ENVIRONMENTAL IMPACT ANALYSIS PROCESS (EIAP) § 989.19 Draft EIS. (a) Preliminary draft. The EPF supports the proponent in preparation of a preliminary draft EIS (PDEIS) (40 CFR 1502.9) based on the scope of issues...

18 CFR 281.212 - Draft tariff and index of entitlements.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 18 Conservation of Power and Water Resources 1 2012-04-01 2012-04-01 false Draft tariff and index... Rule § 281.212 Draft tariff and index of entitlements. (a) Each interstate pipeline shall prepare draft tariff sheets or sections and a draft index of entitlements in accordance with this subpart. (b) The...

18 CFR 281.212 - Draft tariff and index of entitlements.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 18 Conservation of Power and Water Resources 1 2013-04-01 2013-04-01 false Draft tariff and index... Rule § 281.212 Draft tariff and index of entitlements. (a) Each interstate pipeline shall prepare draft tariff sheets or sections and a draft index of entitlements in accordance with this subpart. (b) The...

46 CFR 151.03-35 - Limiting draft.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 5 2012-10-01 2012-10-01 false Limiting draft. 151.03-35 Section 151.03-35 Shipping... BULK LIQUID HAZARDOUS MATERIAL CARGOES Definitions § 151.03-35 Limiting draft. Maximum allowable draft to which a barge may be loaded. Limiting draft is a function of hull type and cargo specific gravity...

18 CFR 281.212 - Draft tariff and index of entitlements.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 18 Conservation of Power and Water Resources 1 2010-04-01 2010-04-01 false Draft tariff and index... Rule § 281.212 Draft tariff and index of entitlements. (a) Each interstate pipeline shall prepare draft tariff sheets or sections and a draft index of entitlements in accordance with this subpart. (b) The...

18 CFR 281.212 - Draft tariff and index of entitlements.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 18 Conservation of Power and Water Resources 1 2011-04-01 2011-04-01 false Draft tariff and index... Rule § 281.212 Draft tariff and index of entitlements. (a) Each interstate pipeline shall prepare draft tariff sheets or sections and a draft index of entitlements in accordance with this subpart. (b) The...

32 CFR 989.19 - Draft EIS.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 32 National Defense 6 2012-07-01 2012-07-01 false Draft EIS. 989.19 Section 989.19 National... ENVIRONMENTAL IMPACT ANALYSIS PROCESS (EIAP) § 989.19 Draft EIS. (a) Preliminary draft. The EPF supports the proponent in preparation of a preliminary draft EIS (PDEIS) (40 CFR 1502.9) based on the scope of issues...

46 CFR 151.03-35 - Limiting draft.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 5 2013-10-01 2013-10-01 false Limiting draft. 151.03-35 Section 151.03-35 Shipping... BULK LIQUID HAZARDOUS MATERIAL CARGOES Definitions § 151.03-35 Limiting draft. Maximum allowable draft to which a barge may be loaded. Limiting draft is a function of hull type and cargo specific gravity...

46 CFR 151.03-35 - Limiting draft.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 5 2011-10-01 2011-10-01 false Limiting draft. 151.03-35 Section 151.03-35 Shipping... BULK LIQUID HAZARDOUS MATERIAL CARGOES Definitions § 151.03-35 Limiting draft. Maximum allowable draft to which a barge may be loaded. Limiting draft is a function of hull type and cargo specific gravity...

18 CFR 281.212 - Draft tariff and index of entitlements.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 18 Conservation of Power and Water Resources 1 2014-04-01 2014-04-01 false Draft tariff and index... Rule § 281.212 Draft tariff and index of entitlements. (a) Each interstate pipeline shall prepare draft tariff sheets or sections and a draft index of entitlements in accordance with this subpart. (b) The...

46 CFR 151.03-35 - Limiting draft.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 5 2014-10-01 2014-10-01 false Limiting draft. 151.03-35 Section 151.03-35 Shipping... BULK LIQUID HAZARDOUS MATERIAL CARGOES Definitions § 151.03-35 Limiting draft. Maximum allowable draft to which a barge may be loaded. Limiting draft is a function of hull type and cargo specific gravity...

32 CFR 989.19 - Draft EIS.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 32 National Defense 6 2013-07-01 2013-07-01 false Draft EIS. 989.19 Section 989.19 National... ENVIRONMENTAL IMPACT ANALYSIS PROCESS (EIAP) § 989.19 Draft EIS. (a) Preliminary draft. The EPF supports the proponent in preparation of a preliminary draft EIS (PDEIS) (40 CFR 1502.9) based on the scope of issues...

46 CFR 167.55-1 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Section 167.55-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS PUBLIC NAUTICAL SCHOOL SHIPS Special Markings Required § 167.55-1 Draft marks and draft indicating systems. (a... are of uniform height equal to the vertical spacing between consecutive marks. (f) Draft marks must be...

46 CFR 167.55-1 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Section 167.55-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS PUBLIC NAUTICAL SCHOOL SHIPS Special Markings Required § 167.55-1 Draft marks and draft indicating systems. (a... are of uniform height equal to the vertical spacing between consecutive marks. (f) Draft marks must be...

46 CFR 167.55-1 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Section 167.55-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS PUBLIC NAUTICAL SCHOOL SHIPS Special Markings Required § 167.55-1 Draft marks and draft indicating systems. (a... are of uniform height equal to the vertical spacing between consecutive marks. (f) Draft marks must be...

46 CFR 167.55-1 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Section 167.55-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS PUBLIC NAUTICAL SCHOOL SHIPS Special Markings Required § 167.55-1 Draft marks and draft indicating systems. (a... are of uniform height equal to the vertical spacing between consecutive marks. (f) Draft marks must be...

46 CFR 167.55-1 - Draft marks and draft indicating systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Section 167.55-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS PUBLIC NAUTICAL SCHOOL SHIPS Special Markings Required § 167.55-1 Draft marks and draft indicating systems. (a... are of uniform height equal to the vertical spacing between consecutive marks. (f) Draft marks must be...

77 FR 21772 - Notification of Two Public Teleconferences of the Science Advisory Board Biogenic Carbon...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-11

... the Panel's draft report on EPA's draft Accounting Framework for Biogenic CO2 Emissions from...'s draft report on EPA's draft Accounting Framework for Biogenic CO2 Emissions from Stationary... Radiation requested SAB review of EPA's draft accounting framework. As noticed in 76 FR 61100-61101, the SAB...

Correspondence standards

NASA Technical Reports Server (NTRS)

1992-01-01

This revised handbook covers the drafting, preparation, and review of NASA letters, memorandums, informal communications, electronic communications, envelopes and mailing, and classified correspondence. The appendices address specific guidelines for administrator's correspondence, White House and Congressional correspondance, Privacy Act correspondence, and foreign correspondence. Also incorporated as appendices are quick references for forms of address, compound words, and capitalization of words frequently used at NASA.

Racial Differences in Why Women Work. Revised Draft.

ERIC Educational Resources Information Center

Beckett, Joyce O.

A study was conducted to examine the contemporary differences in the response of black and white wives to factors that play a determining role in the decision of a wife to seek paid employment. Data, in the form of husbands' responses to interviews, were collected from a national sample of husband-wife families who resided in the continental…

Beyond Reason: The Media, Politics, and Public Discourse. Draft.

ERIC Educational Resources Information Center

Dorman, William A.

The media have a lot to do with how people think and what people think about. The line between popular culture and news has virtually disappeared, giving rise to what some have labeled "infotainment." At the same time, "fake news" in the form of publicity that promoters provide to media outlets under the guise of legitimate…

76 FR 22926 - Notice of Availability of Draft Environmental Assessment and Finding of No Significant Impact for...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-25

... the following methods: Federal Rulemaking Web site: Go to http://www.regulations.gov and search for... writing or in electronic form will be posted on the NRC Web site and on the Federal rulemaking Web site... electronically under ADAMS Accession Number ML110870992. Federal Rulemaking Web site: Public comments and...

75 FR 13600 - Nine Mile Point Nuclear Station, LLC, Nine Mile Point Nuclear Station, Unit No. 2; Draft...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-22

... shielding design and the ALARA program would continue in its current form. Offsite Doses at EPU Conditions..., such as fossil fuel or alternative fuel power generation, to provide electric generation capacity to offset future demand. Construction and operation of such a fossil-fueled or alternative-fueled plant may...

76 FR 39890 - St. Johns National Wildlife Refuge, FL; Draft Comprehensive Conservation Plan and Environmental...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-07

... would determine the size, seasonality, and frequency of prescribed fires to benefit rail species. We... response. We would work to restore the hydrologic setting to benefit marsh birds and determine the role of..., cattle grazing, and/ or other forms of vegetation maintenance to benefit this species on the Bee Line...

How to Plan an Ordinance: An Outline and Some Examples.

ERIC Educational Resources Information Center

Cable Television Information Center, Washington, DC.

Designed for public officials who must make policy decisions concerning cable television, this booklet forms a checklist to ensure that all basic questions have been considered in drafting an ordinance. The purpose of a cable television ordinance is to develop a law listing the specifications and obligations that will govern the franchising of a…

Transforming Glycoscience: A Roadmap for the Future

Treesearch

Robert Moon

2012-01-01

This report has been reviewed in draft form by persons chosen for their diverse perspectives and technical expertise in accordance with procedures approved by the National Research Council’s Report Review Committee. The purpose of this independent review is to provide candid and critical comments that will assist the institution in making the published report as sound...

77 FR 57084 - National Pollutant Discharge Elimination System (NPDES): Draft General Permit for Point Source...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-17

..., including to conveyances to Waters of the United States, including interstate waters that flow across or... Treatment Systems to Waters of the United States, Including to Conveyances to Waters of the United States, Including Interstate Waters That Flow Across or Form Part of the Boundary of Illinois and in All Areas of...

Validation of an In Vitro Bioaccessability Test Method for the Estimation of the Bioavailability of Arsenic from Soil and Sediment

DTIC Science & Technology

2012-12-01

evaluate predictive performance following methods described in Malinowski et al. (1997). Acceptance criteria and control limits will be based on...69: 69–78. Malinowski , H., P. Marroum, V.R. Uppoor, et al. 1997. Draft guidance for industry extended release solid oral dosage forms. In: Young D

Flow characteristics and spillage mechanisms of wall-mounted and jet-isolated range hoods subject to influence from cross draft.

PubMed

Chen, Jia-Kun; Huang, Rong Fung; Peng, Kuan-Lin

2012-01-01

The effects of draft on the flow and spillage characteristics of wall-mounted and jet-isolated range hoods were investigated. A specially designed draft generator that could supply low-swirl air current was used to provide "cross draft" from three directions, lateral (θ = 0(o)), oblique (θ = 45(o)), and front (θ = 90(o)), with respect to the center point of the range hoods. Flow characteristics of oil mist were inspected through visualization of smoke flows with light scattering (laser light sheet-assisted visualization of smoke flow). The leakage mechanisms, which were closely related to the flow features, were studied by examining both movies and still pictures showing smoke-flow evolution. The sulfur hexafluoride tracer gas concentration detection method was employed to measure the capture indices. The results showed that the lateral draft pushed the pollutants generated under the hood in the opposite direction and induced serious spillage. The oblique draft pushed the pollutants toward both the rear wall and opposite side and induced more serious spillage than did the lateral draft. The frontal draft forced the pollutants to bifurcate into streams moving toward the left and the right, and induced the most serious pollutant spillage among the three tested drafts. Pollutant spillage became critically significant as the cross draft velocity was increased to greater than 0.2 m/sec. Spillage of pollutants increased as the velocity of the cross draft was increased. Increasing the suction flow rate of the range hood may increase resistance to the draft, but the benefits were limited at draft velocities greater than 0.2 m/sec. Both range hoods had a similarly low capture index under the influence of the lateral draft. For the oblique and frontal drafts, the jet-isolated range hood demonstrated a higher capture index than did the wall-mounted range hood.

Ice Roughness and Thickness Evolution on a Swept NACA 0012 Airfoil

NASA Technical Reports Server (NTRS)

McClain, Stephen T.; Vargas, Mario; Tsao, Jen-Ching

2017-01-01

Several recent studies have been performed in the Icing Research Tunnel (IRT) at NASA Glenn Research Center focusing on the evolution, spatial variations, and proper scaling of ice roughness on airfoils without sweep exposed to icing conditions employed in classical roughness studies. For this study, experiments were performed in the IRT to investigate the ice roughness and thickness evolution on a 91.44-cm (36-in.) chord NACA 0012 airfoil, swept at 30-deg with 0deg angle of attack, and exposed to both Appendix C and Appendix O (SLD) icing conditions. The ice accretion event times used in the study were less than the time required to form substantially three-dimensional structures, such as scallops, on the airfoil surface. Following each ice accretion event, the iced airfoils were scanned using a ROMER Absolute Arm laser-scanning system. The resulting point clouds were then analyzed using the self-organizing map approach of McClain and Kreeger to determine the spatial roughness variations along the surfaces of the iced airfoils. The resulting measurements demonstrate linearly increasing roughness and thickness parameters with ice accretion time. Further, when compared to dimensionless or scaled results from unswept airfoil investigations, the results of this investigation indicate that the mechanisms for early stage roughness and thickness formation on swept wings are similar to those for unswept wings.

Modeling of surface roughness effects on glaze ice accretion

NASA Technical Reports Server (NTRS)

Hansman, R. John, Jr.; Yamaguchi, Keiko; Berkowitz, Brian M.; Potapczuk, Mark

1990-01-01

A series of experimental investigations focused on studying the cause and effect of roughness on accreting glaze ice surfaces were conducted. Detailed microvideo observations were made of glaze ice accretions on 1 to 4 inch diameter cylinders in three icing wind tunnels (the Data Products of New England six inch test facility, the NASA Lewis Icing Research Tunnel, and the B. F. Goodrich Ice Protection Research Facility). Infrared thermal video recordings were made of accreting ice surfaces in the Goodrich facility. Distinct zones of surface water behavior were observed; a smooth wet zone in the stagnation region with a uniform water film; a rough zone where surface tension effects caused coalescence of surface water into stationary beads; a horn zone where roughness elements grow into horn shapes; a runback zone where surface water ran back as rivulets; and a dry zone where rime feathers formed. The location of the transition from the smooth to the rough zone was found to migrate with time towards the stagnation point. The behavior of the transition appeared to be controlled by boundary layer transition and bead formation mechanisms at the interface between the smooth and rough zones. Regions of wet ice growth and enhanced heat transfer were clearly visible in the infrared video recordings of glaze ice surfaces. A simple multi-zone modification to the current glaze ice accretion model was proposed to include spatial variability in surface roughness.

Experimental and simulation study of growth of TiO2 films on different substrates and its applications

NASA Astrophysics Data System (ADS)

Ghogare, Trupti T.; Kartha, Moses J.; Kendre, Subhash D.; Pathan, Habib M.

2018-04-01

Monte-Carlo Ballistic Deposition simulations have done on substrates with different initial roughness. The grown films were observed to be porous. The initial growths of the films with seed like initiations are observed for substrate with high initial roughness. In order to confirm this effect TiO2 films were deposited on different substrates using chemical bath deposition. The surface morphological and optical properties were measured using scanning electron microscopy and a UV-Vis spectrophotometer. Flower like porous structure are obtained on glass substrate and continuous porous morphology is formed on ITO substrate. The morphology of the surfaces was successfully reconstructed and the surface porosity was calculated after digitalising images and reconstructed the surfaces. The TiO2 film formed on ITO is observed to be 10% more porous than on the film formed on glass substrate. Diffusion Limited Aggregation simulations with multiple seeds confirms that the observed flower like structure formed are due to the screening effects of the diffusing ion by already deposited particles.

Wall fluidization in two acts: from stiff to soft roughness.

PubMed

Derzsi, Ladislav; Filippi, Daniele; Lulli, Matteo; Mistura, Giampaolo; Bernaschi, Massimo; Garstecki, Piotr; Sbragaglia, Mauro; Pierno, Matteo

2018-02-14

Fluidization of soft glassy materials (SGMs) in microfluidic channels is affected by the wall roughness in the form of microtexturing. When SGMs flow across microgrooves, their constituents are likely trapped within the grooves' gap, and the way they are released locally modifies the fluidization close to the walls. By leveraging a suitable combination of experiments and numerical simulations on concentrated emulsions (a model SGM), we quantitatively report the existence of two physically different scenarios. When the gap is large compared to the droplets in the emulsion, the droplets hit the solid obstacles and easily escape scrambling with their neighbors. Conversely, as the gap spacing is reduced, droplets get trapped inside, creating a "soft roughness" layer, i.e. a complementary series of deformable posts from which overlying droplets are in turn released. In both cases, the induced fluidization scales with the grooves' density, although with a reduced prefactor for narrow gaps, accounting for the softness of the roughness. Both scenarios are also well distinguished via the statistics of the droplets displacement field close to the walls, with large deviations induced by the surface roughness, depending on its stiffness.

76 FR 50729 - Science Advisory Board Staff Office; Notification of a Public Teleconference of the Chartered...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-16

... SAB report, Peer Review of EPA's Draft National-Scale Mercury Risk Assessment (08/04/11) Draft. DATES... SAB draft report entitled Peer Review of EPA's Draft National-Scale Mercury Risk Assessment (08/04/1...)(1)(A) of the Clean Air Act (CAA). EPA developed a draft risk assessment for mercury, entitled...

12 CFR 516.20 - What information must I include in my draft business plan?

Code of Federal Regulations, 2013 CFR

2013-01-01

... 12 Banks and Banking 6 2013-01-01 2012-01-01 true What information must I include in my draft... What information must I include in my draft business plan? If you must submit a draft business plan... described in the savings association's draft business plan; and (d) Demonstrate how applicable requirements...

12 CFR 516.20 - What information must I include in my draft business plan?

Code of Federal Regulations, 2012 CFR

2012-01-01

... 12 Banks and Banking 6 2012-01-01 2012-01-01 false What information must I include in my draft... What information must I include in my draft business plan? If you must submit a draft business plan... described in the savings association's draft business plan; and (d) Demonstrate how applicable requirements...

12 CFR 116.20 - What information must I include in my draft business plan?

Code of Federal Regulations, 2014 CFR

2014-01-01

... 12 Banks and Banking 1 2014-01-01 2014-01-01 false What information must I include in my draft... What information must I include in my draft business plan? If you must submit a draft business plan... described in the savings association's draft business plan; and (d) Demonstrate how applicable requirements...

12 CFR 116.20 - What information must I include in my draft business plan?

Code of Federal Regulations, 2012 CFR

2012-01-01

... 12 Banks and Banking 1 2012-01-01 2012-01-01 false What information must I include in my draft... What information must I include in my draft business plan? If you must submit a draft business plan... described in the savings association's draft business plan; and (d) Demonstrate how applicable requirements...

12 CFR 116.20 - What information must I include in my draft business plan?

Code of Federal Regulations, 2013 CFR

2013-01-01

... 12 Banks and Banking 1 2013-01-01 2013-01-01 false What information must I include in my draft... What information must I include in my draft business plan? If you must submit a draft business plan... described in the savings association's draft business plan; and (d) Demonstrate how applicable requirements...

12 CFR 516.20 - What information must I include in my draft business plan?

Code of Federal Regulations, 2014 CFR

2014-01-01

... 12 Banks and Banking 6 2014-01-01 2012-01-01 true What information must I include in my draft... What information must I include in my draft business plan? If you must submit a draft business plan... described in the savings association's draft business plan; and (d) Demonstrate how applicable requirements...

12 CFR 516.20 - What information must I include in my draft business plan?

Code of Federal Regulations, 2011 CFR

2011-01-01

... 12 Banks and Banking 5 2011-01-01 2011-01-01 false What information must I include in my draft... What information must I include in my draft business plan? If you must submit a draft business plan... described in the savings association's draft business plan; and (d) Demonstrate how applicable requirements...

Comparison of Conventional and Computer-Aided Drafting Methods from the View of Time and Drafting Quality

ERIC Educational Resources Information Center

Ozkan, Aysen; Yildirim, Kemal

2016-01-01

Problem Statement: Drafting course is essential for students in the design disciplines for becoming more organized and for complying with standards in the educational system. Drafting knowledge is crucial, both for comprehension of the issues and for the implementation phase. In any design project, drafting performance and success are as important…

10 CFR 51.74 - Distribution of draft environmental impact statement and supplement to draft environmental impact...

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 2 2011-01-01 2011-01-01 false Distribution of draft environmental impact statement and supplement to draft environmental impact statement; news releases. 51.74 Section 51.74 Energy NUCLEAR... environmental impact statement; news releases. (a) A copy of the draft environmental impact statement will be...

10 CFR 51.74 - Distribution of draft environmental impact statement and supplement to draft environmental impact...

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 2 2012-01-01 2012-01-01 false Distribution of draft environmental impact statement and supplement to draft environmental impact statement; news releases. 51.74 Section 51.74 Energy NUCLEAR... environmental impact statement; news releases. (a) A copy of the draft environmental impact statement will be...

10 CFR 51.74 - Distribution of draft environmental impact statement and supplement to draft environmental impact...

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 2 2014-01-01 2014-01-01 false Distribution of draft environmental impact statement and supplement to draft environmental impact statement; news releases. 51.74 Section 51.74 Energy NUCLEAR... environmental impact statement; news releases. (a) A copy of the draft environmental impact statement will be...

10 CFR 51.74 - Distribution of draft environmental impact statement and supplement to draft environmental impact...

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 2 2013-01-01 2013-01-01 false Distribution of draft environmental impact statement and supplement to draft environmental impact statement; news releases. 51.74 Section 51.74 Energy NUCLEAR... environmental impact statement; news releases. (a) A copy of the draft environmental impact statement will be...

10 CFR 51.74 - Distribution of draft environmental impact statement and supplement to draft environmental impact...

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Distribution of draft environmental impact statement and supplement to draft environmental impact statement; news releases. 51.74 Section 51.74 Energy NUCLEAR... environmental impact statement; news releases. (a) A copy of the draft environmental impact statement will be...

78 FR 19733 - Draft General Management Plan and Draft Environmental Impact Statement, Fort Raleigh National...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-02

... Management Plan (EIS/GMP) for Fort Raleigh National Historic Site, North Carolina. The draft describes and... announce the dates, times, and locations of public meetings on the draft EIS/GMP through the NPS Planning... delivery to the above address. Electronic copies of the Draft EIS/GMP will be available online at http...

76 FR 72718 - Notice of Availability of the Draft Baker Resource Management Plan and Environmental Impact...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-25

....HAG11-0127] Notice of Availability of the Draft Baker Resource Management Plan and Environmental Impact... Draft Resource Management Plan (RMP) and Draft Environmental Impact Statement (EIS) for the Baker... conditions, and changes in resource management practices since the Baker RMP of 1989. The Draft RMP/EIS was...

46 CFR 174.040 - Stability requirements: general.

Code of Federal Regulations, 2011 CFR

2011-10-01

... metacentric height in the upright equilibrium position for the full range of drafts, whether at the operating draft for navigation, towing, or drilling afloat, or at a temporary draft when changing drafts. ...

46 CFR 174.040 - Stability requirements: general.

Code of Federal Regulations, 2014 CFR

2014-10-01

... metacentric height in the upright equilibrium position for the full range of drafts, whether at the operating draft for navigation, towing, or drilling afloat, or at a temporary draft when changing drafts. ...

Development of a Draft Core Set of Domains for Measuring Shared Decision Making in Osteoarthritis: An OMERACT Working Group on Shared Decision Making.

PubMed

Toupin-April, Karine; Barton, Jennifer; Fraenkel, Liana; Li, Linda; Grandpierre, Viviane; Guillemin, Francis; Rader, Tamara; Stacey, Dawn; Légaré, France; Jull, Janet; Petkovic, Jennifer; Scholte-Voshaar, Marieke; Welch, Vivian; Lyddiatt, Anne; Hofstetter, Cathie; De Wit, Maarten; March, Lyn; Meade, Tanya; Christensen, Robin; Gaujoux-Viala, Cécile; Suarez-Almazor, Maria E; Boonen, Annelies; Pohl, Christoph; Martin, Richard; Tugwell, Peter S

2015-12-01

Despite the importance of shared decision making for delivering patient-centered care in rheumatology, there is no consensus on how to measure its process and outcomes. The aim of this Outcome Measures in Rheumatology (OMERACT) working group is to determine the core set of domains for measuring shared decision making in intervention studies in adults with osteoarthritis (OA), from the perspectives of patients, health professionals, and researchers. We followed the OMERACT Filter 2.0 method to develop a draft core domain set by (1) forming an OMERACT working group; (2) conducting a review of domains of shared decision making; and (3) obtaining opinions of all those involved using a modified nominal group process held at a session activity at the OMERACT 12 meeting. In all, 26 people from Europe, North America, and Australia, including 5 patient research partners, participated in the session activity. Participants identified the following domains for measuring shared decision making to be included as part of the draft core set: (1) identifying the decision, (2) exchanging information, (3) clarifying views, (4) deliberating, (5) making the decision, (6) putting the decision into practice, and (7) assessing the effect of the decision. Contextual factors were also suggested. We proposed a draft core set of shared decision-making domains for OA intervention research studies. Next steps include a workshop at OMERACT 13 to reach consensus on these proposed domains in the wider OMERACT group, as well as to detail subdomains and assess instruments to develop a core outcome measurement set.

Smoking prevention and cessation in the Africa and Middle East region: a consensus draft guideline for healthcare providers--executive summary.

PubMed

Ali, Ahmed Yousif M; Safwat, Tarek; Onyemelukwe, Geoffrey; Otaibi, Moh'd Amin Al; Amir, Ashraf A; Nawas, Yousef N; Aouina, Hichem; Afif, Moulay Hicham; Bolliger, Chris T

2012-01-01

Despite the abundance of scientific evidence confirming the health consequences of smoking and other forms of tobacco use, the tobacco epidemic remains an important public health problem and by 2030 it is predicted that more than 80% of tobacco deaths will be in developing countries. In Africa and the Middle East, many local factors contribute to the initiation and maintenance of tobacco use. Although efforts to reduce the mortality and morbidity associated with smoking and tobacco dependence are underway, there is a need for guidance on how to utilize appropriate tobacco control policies and psychology- and pharmacology-based therapies to counter tobacco dependence as recommended by the Framework Convention on Tobacco Control (FCTC). A group of tobacco cessation experts from public health services and/or academic institutions in Africa and the Middle East participated in a series of four meetings held in Cairo, Cape Town, and Dubai between May 2008 and February 2011 to develop a draft guideline tailored to their region. This article provides the background to the development of this draft smoking cessation guideline and discusses how the recommendations can be implemented and progress monitored to promote both primary prevention and cessation of tobacco use within our countries. The draft guideline for Africa and the Middle East provides an important resource in combating the devastating effects of tobacco use in these regions which can be further localized through engagement with local stakeholders in the countries of the region. Copyright © 2012 S. Karger AG, Basel.

Development of a Draft Core Set of Domains for Measuring Shared Decision Making in Osteoarthritis: An OMERACT Working Group on Shared Decision Making

PubMed Central

Toupin April, Karine; Barton, Jennifer; Fraenkel, Liana; Li, Linda; Grandpierre, Viviane; Guillemin, Francis; Rader, Tamara; Stacey, Dawn; Légaré, France; Jull, Janet; Petkovic, Jennifer; Scholte Voshaar, Marieke; Welch, Vivian; Lyddiatt, Anne; Hofstetter, Cathie; De Wit, Maarten; March, Lyn; Meade, Tanya; Christensen, Robin; Gaujoux-Viala, Cécile; Suarez-Almazor, Maria E.; Boonen, Annelies; Pohl, Christoph; Martin, Richard; Tugwell, Peter

2015-01-01

Objective Despite the importance of shared decision making for delivering patient-centred care in rheumatology, there is no consensus on how to measure its process and outcomes. The aim of this OMERACT working group is to determine the core set of domains for measuring shared decision making in intervention studies in adults with osteoarthritis (OA), from the perspective of patients, health professionals and researchers. Methods We followed the OMERACT Filter 2.0 to develop a draft core domain set, which consisted of: (i) forming an OMERACT working group; (ii) conducting a review of domains of shared decision making; and (iii) obtaining the opinions of stakeholders using a modified nominal group process held at a session activity at the OMERACT 2014 meeting. Results 26 stakeholders from Europe, North America and Australia, including 5 patient research partners, participated in the session activity. Participants identified the following domains for measuring shared decision making to be included as part of the Draft Core Set: 1) Identifying the decision; 2) Exchanging Information; 3) Clarifying views; 4) Deliberating; 5) Making the decision; 6) Putting the decision into practice; and 7) Assessing the impact of the decision. Contextual factors were also suggested. Conclusion We propose a Draft Core Set of shared decision making domains for OA intervention research studies. Next steps include a workshop at OMERACT 2016 to reach consensus on these proposed domains in the wider OMERACT group, as well as detail sub-domains and assess instruments to develop a Core Outcome Measurement Set. PMID:25877502

A study of flow in alluvial channels: the effect of large concentrations of fine sediment on the mechanics of flow in a small flume

USGS Publications Warehouse

Haushild, William Leland; Simons, Daryl Baldwin; Richadrson, Everett V.

1961-01-01

concentration with the dune bed form and was increased by as much as 550 percent for the transition, standing wave, and antidune forms of bed roughness. Resistance to flow was less (C/√ g increased by 45 percent) with fine sediment-laden flow than with clear-water flow for the dune, and transition bed forms; and was greater (C/√ g   reduced by 25 percent) for the standing waves and the antidunes. A narrow range of bentonite concentration for each form of bed roughness was established as a limit below which only minor changes in bed form, bed material transport, and resistance to flow occurred. The variation of the liquid properties, specific weight and viscosity, for water-bentonite dispersions were studied and their effect on the properties of the bed material particles measured. The fall velocity of the particles in a dispersion of 100, 000 parts per million fine sediment in water was reduced to about one-half their fall velocity in clear water.

A mutation in the LAMC2 gene causes the Herlitz junctional epidermolysis bullosa (H-JEB) in two French draft horse breeds.

PubMed

Milenkovic, Dragan; Chaffaux, Stéphane; Taourit, Sead; Guérin, Gérard

2003-01-01

Epidermolysis bullosa (EB) is a heterogeneous group of inherited diseases characterised by skin blistering and fragility. In humans, one of the most severe forms of EB known as Herlitz-junctional EB (H-JEB), is caused by mutations in the laminin 5 genes. EB has been described in several species, like cattle, sheep, dogs, cats and horses where the mutation, a cytosine insertion in exon 10 of the LAMC2 gene, was very recently identified in Belgian horses as the mutation responsible for JEB. In this study, the same mutation was found to be totally associated with the JEB phenotype in two French draft horse breeds, Trait Breton and Trait Comtois. This result provides breeders a molecular test to better manage their breeding strategies by genetic counselling.

Light emitting diode with high aspect ratio submicron roughness for light extraction and methods of forming

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Ting

The surface morphology of an LED light emitting surface is changed by applying a reactive ion etch (RIE) process to the light emitting surface. High aspect ratio, submicron roughness is formed on the light emitting surface by transferring a thin film metal hard-mask having submicron patterns to the surface prior to applying a reactive ion etch process. The submicron patterns in the metal hard-mask can be formed using a low cost, commercially available nano-patterned template which is transferred to the surface with the mask. After subsequently binding the mask to the surface, the template is removed and the RIE processmore » is applied for time duration sufficient to change the morphology of the surface. The modified surface contains non-symmetric, submicron structures having high aspect ratio which increase the efficiency of the device.« less

New fabrication method for an ellipsoidal neutron focusing mirror with a metal substrate.

PubMed

Guo, Jiang; Takeda, Shin; Morita, Shin-ya; Hino, Masahiro; Oda, Tatsuro; Kato, Jun-ichi; Yamagata, Yutaka; Furusaka, Michihiro

2014-10-06

We propose an ellipsoidal neutron focusing mirror using a metal substrate made with electroless nickel-phosphorus (NiP) plated material for the first time. Electroless NiP has great advantages for realizing an ellipsoidal neutron mirror because of its amorphous structure, good machinability and relatively large critical angle of total reflection for neutrons. We manufactured the mirror by combining ultrahigh precision cutting and fine polishing to generate high form accuracy and low surface roughness. The form accuracy of the mirror was estimated to be 5.3 μm P-V and 0.8 μm P-V for the minor-axis and major-axis direction respectively, while the surface roughness was reduced to 0.2 nm rms. The effect of form error on focusing spot size was evaluated by using a laser beam and the focusing performance of the mirror was verified by neutron experiments.

Relation between skin micro-topography, roughness, and skin age.

PubMed

Trojahn, C; Dobos, G; Schario, M; Ludriksone, L; Blume-Peytavi, U; Kottner, J

2015-02-01

The topography of the skin surface consists of lines, wrinkles, and scales. Primary and secondary lines form a network like structure that may be identified as polygons. Skin surface roughness measurements are widely applied in dermatological research and practice but the relation between roughness parameters and their anatomical equivalents are unclear. This study aimed to investigate whether the number of closed polygons (NCP) per measurement field can be used as a reliable parameter to measure skin surface topography. For this purpose, we analysed the relation between skin surface roughness parameters and NCP in different age groups. Images of the volar forearm skin of 38 subjects (14 children, 12 younger, and 12 older adults) were obtained with the VisioScan VC98. The NCP was counted by three independent researchers and selected roughness parameters were measured. Interrater reliability of counting the number of closed polygons and correlations between NCP, roughness parameters, and age were calculated. The mean NCP/mm² in children was 3.1 (SD 1.1), in younger adults 1.0 (SD 0.7), and in older adults 1.0 (SD 0.9). The interrater reliability was 0.9. A negative correlation of NCP/mm² with age was observed, whereas measured roughness parameters were positively associated with age. NCP/mm² was weakly related to skin roughness. The NCP/mm² is a reproducible parameter for characterizing the skin surface topography. It is proposed as an additional parameter in dermatological research and practice because it represents distinct aspects of the cutaneous profile not covered by established roughness parameters. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Pore-wall roughness as a fractal surface and theoretical simulation of mercury intrusion/retraction in porous media

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tsakiroglou, C.D.; Payatakes, A.C.

The mercury intrusion/retraction curves of many types of porous materials (e.g., sandstones) have sections of finite slope in the region of high and very high pressure. This feature is attributed to the existence of microroughness on the pore walls. In the present work pore-wall roughness features are added to a three-dimensional primary network of chambers-and-throats using ideas of fractal geometry. The roughness of the throats is modeled with a finite number of self-similar triangular prisms of progressively smaller sizes. The roughness of the chambers is modeled in a similar way using right circular cones instead of prisms. Three parameters sufficemore » for the complete characterization of the model of fractal roughness, namely, the number of features per unit length, the common angle of sharpness, and the number of layers (which is taken to be the same for throats and chambers). Analytical relations that give the surface area, pore volume, and mercury saturation of the pore network as functions of the fractal roughness parameters are developed for monolayer and multilayer arrangements. The chamber-and-throat network with fractal pore-wall roughness is used to develop an extended version of the computer-aided simulator of mercury porosimetry that has been reported in previous publications. This new simulator is used to investigate the effects of the roughness features on the form of mercury intrusion/retraction curves. It turns out that the fractal model of the porewall roughness gives an adequate representation of real porous media, and capillary pressure curves which are similar to the experimental ones for many typical porous materials such as sandstones. The method is demonstrated with the analysis of a Greek sandstone.« less

Turbulent Flow Over Large Roughness Elements: Effect of Frontal and Plan Solidity on Turbulence Statistics and Structure

NASA Astrophysics Data System (ADS)

Placidi, M.; Ganapathisubramani, B.

2018-04-01

Wind-tunnel experiments were carried out on fully-rough boundary layers with large roughness (δ /h ≈ 10, where h is the height of the roughness elements and δ is the boundary-layer thickness). Twelve different surface conditions were created by using LEGO™ bricks of uniform height. Six cases are tested for a fixed plan solidity (λ _P) with variations in frontal density (λ _F), while the other six cases have varying λ _P for fixed λ _F. Particle image velocimetry and floating-element drag-balance measurements were performed. The current results complement those contained in Placidi and Ganapathisubramani (J Fluid Mech 782:541-566, 2015), extending the previous analysis to the turbulence statistics and spatial structure. Results indicate that mean velocity profiles in defect form agree with Townsend's similarity hypothesis with varying λ _F, however, the agreement is worse for cases with varying λ _P. The streamwise and wall-normal turbulent stresses, as well as the Reynolds shear stresses, show a lack of similarity across most examined cases. This suggests that the critical height of the roughness for which outer-layer similarity holds depends not only on the height of the roughness, but also on the local wall morphology. A new criterion based on shelter solidity, defined as the sheltered plan area per unit wall-parallel area, which is similar to the `effective shelter area' in Raupach and Shaw (Boundary-Layer Meteorol 22:79-90, 1982), is found to capture the departure of the turbulence statistics from outer-layer similarity. Despite this lack of similarity reported in the turbulence statistics, proper orthogonal decomposition analysis, as well as two-point spatial correlations, show that some form of universal flow structure is present, as all cases exhibit virtually identical proper orthogonal decomposition mode shapes and correlation fields. Finally, reduced models based on proper orthogonal decomposition reveal that the small scales of the turbulence play a significant role in assessing outer-layer similarity.

Pathogenicity of Peptostreptococcus micros morphotypes and Prevotella species in pure and mixed culture.

PubMed

van Dalen, P J; van Deutekom-Mulder, E C; de Graaff, J; van Steenbergen, T J

1998-02-01

Recently, an atypical rough colony morphotype of Peptostreptococcus micros, a species which is found in ulcerating infections, including periodontitis, was isolated. The virulence of morphotypes alone and in combination with Prevotella intermedia and P. nigrescens was investigated both in vivo and in vitro. All strains tested induced abscesses containing fluid pus in a mouse skin model, and lesions caused by monocultures of the rough morphotype strains of P. micros were statistically significantly larger than those induced by the smooth morphotype strains. Inocula containing both morphotypes produced similar sized abscesses compared to mono-inocula containing the same bacterial load. Both Prevotella species induced small abscesses when inoculated alone, and when Pr. nigrescens was inoculated with one of the other strains, the abscesses were not significantly different from the abscesses induced by the mono-infections of this strain. Synergy, in terms of higher numbers of colony forming units (cfu) in the mixed inocula, was found for all combinations of the rough morphotypes of P. micros and both Prevotella spp. Pus from abscesses caused by combinations of Peptostreptococcus and Prevotella spp. transmitted the infection to other mice, but no abscesses were formed in mice inoculated with pus induced by mono-inocula. These results demonstrated synergic activity between both rough and smooth P. micros strains and oral Prevotella strains. The in-vitro co-culture experiments produced no evidence of growth stimulation. The effect of P. micros strains on the immune system was investigated by testing their ability to initiate luminol-dependent chemiluminescence of polymorphonuclear leucocytes in the presence and absence of human serum. In the latter, the rough morphotype strains initiated higher counts than the smooth morphotype strains. Further work is needed to elucidate the difference in virulence between the smooth and the rough morphotype cells of P. micros and the nature of the interaction with the Prevotella spp.

Guided self-assembly of nanostructured titanium oxide

NASA Astrophysics Data System (ADS)

Wang, Baoxiang; Rozynek, Zbigniew; Fossum, Jon Otto; Knudsen, Kenneth D.; Yu, Yingda

2012-02-01

A series of nanostructured titanium oxide particles were synthesized by a simple wet chemical method and characterized by means of small-angle x-ray scattering (SAXS)/wide-angle x-ray scattering (WAXS), atomic force microscope (AFM), scanning electron microscope (SEM), transmission electron microscope (TEM), thermal analysis, and rheometry. Tetrabutyl titanate (TBT) and ethylene glycol (EG) can be combined to form either TiOx nanowires or smooth nanorods, and the molar ratio of TBT:EG determines which of these is obtained. Therefore, TiOx nanorods with a highly rough surface can be obtained by hydrolysis of TBT with the addition of cetyl-trimethyl-ammonium bromide (CTAB) as surfactant in an EG solution. Furthermore, TiOx nanorods with two sharp ends can be obtained by hydrolysis of TBT with the addition of salt (LiCl) in an EG solution. The AFM results show that the TiOx nanorods with rough surfaces are formed by the self-assembly of TiOx nanospheres. The electrorheological (ER) effect was investigated using a suspension of titanium oxide nanowires or nanorods dispersed in silicone oil. Oil suspensions of titanium oxide nanowires or nanorods exhibit a dramatic reorganization when submitted to a strong DC electric field and the particles aggregate to form chain-like structures along the direction of applied electric field. Two-dimensional SAXS images from chains of anisotropically shaped particles exhibit a marked asymmetry in the SAXS patterns, reflecting the preferential self-assembly of the particles in the field. The suspension of rough TiOx nanorods shows stronger ER properties than that of the other nanostructured TiOx particles. We find that the particle surface roughness plays an important role in modification of the dielectric properties and in the enhancement of the ER effect.

Guided self-assembly of nanostructured titanium oxide.

PubMed

Wang, Baoxiang; Rozynek, Zbigniew; Fossum, Jon Otto; Knudsen, Kenneth D; Yu, Yingda

2012-02-24

A series of nanostructured titanium oxide particles were synthesized by a simple wet chemical method and characterized by means of small-angle x-ray scattering (SAXS)/wide-angle x-ray scattering (WAXS), atomic force microscope (AFM), scanning electron microscope (SEM), transmission electron microscope (TEM), thermal analysis, and rheometry. Tetrabutyl titanate (TBT) and ethylene glycol (EG) can be combined to form either TiO(x) nanowires or smooth nanorods, and the molar ratio of TBT:EG determines which of these is obtained. Therefore, TiO(x) nanorods with a highly rough surface can be obtained by hydrolysis of TBT with the addition of cetyl-trimethyl-ammonium bromide (CTAB) as surfactant in an EG solution. Furthermore, TiO(x) nanorods with two sharp ends can be obtained by hydrolysis of TBT with the addition of salt (LiCl) in an EG solution. The AFM results show that the TiO(x) nanorods with rough surfaces are formed by the self-assembly of TiO(x) nanospheres. The electrorheological (ER) effect was investigated using a suspension of titanium oxide nanowires or nanorods dispersed in silicone oil. Oil suspensions of titanium oxide nanowires or nanorods exhibit a dramatic reorganization when submitted to a strong DC electric field and the particles aggregate to form chain-like structures along the direction of applied electric field. Two-dimensional SAXS images from chains of anisotropically shaped particles exhibit a marked asymmetry in the SAXS patterns, reflecting the preferential self-assembly of the particles in the field. The suspension of rough TiO(x) nanorods shows stronger ER properties than that of the other nanostructured TiO(x) particles. We find that the particle surface roughness plays an important role in modification of the dielectric properties and in the enhancement of the ER effect.

The evolution of a colluvial hollow to a fluvial channel with periodic steps following two transformational disturbances: A wildfire and a historic flood

NASA Astrophysics Data System (ADS)

Rengers, F. K.; McGuire, L. A.; Ebel, B. A.; Tucker, G. E.

2018-05-01

The transition of a colluvial hollow to a fluvial channel with discrete steps was observed after two landscape-scale disturbances. The first disturbance, a high-severity wildfire, changed the catchment hydrology to favor overland flow, which incised a colluvial hollow, creating a channel in the same location. This incised channel became armored with cobbles and boulders following repeated post-wildfire overland flow events. Three years after the fire, a record rainstorm produced regional flooding and generated sufficient fluvial erosion and sorting to produce a fluvial channel with periodically spaced steps. An analysis of the step spacing shows that after the flood, newly formed steps retained a similar spacing to the topographic roughness spacing in the original colluvial hollow (prior to channelization). This suggests that despite a distinct change in channel form roughness and bedform morphology, the endogenous roughness periodicity was conserved. Variations in sediment erodibility helped to create the emergent steps as the largest particles (>D84) remained immobile, becoming step features, and downstream soil was easily winnowed away.

The evolution of a colluvial hollow to a fluvial channel with periodic steps following two transformational disturbances: A wildfire and a historic flood

USGS Publications Warehouse

Rengers, Francis K.; McGuire, Luke; Ebel, Brian A.; Tucker, G. E.

2018-01-01

The transition of a colluvial hollow to a fluvial channel with discrete steps was observed after two landscape-scale disturbances. The first disturbance, a high-severity wildfire, changed the catchment hydrology to favor overland flow, which incised a colluvial hollow, creating a channel in the same location. This incised channel became armored with cobbles and boulders following repeated post-wildfire overland flow events. Three years after the fire, a record rainstorm produced regional flooding and generated sufficient fluvial erosion and sorting to produce a fluvial channel with periodically spaced steps. An analysis of the step spacing shows that after the flood, newly formed steps retained a similar spacing to the topographic roughness spacing in the original colluvial hollow (prior to channelization). This suggests that despite a distinct change in channel form roughness and bedform morphology, the endogenous roughness periodicity was conserved. Variations in sediment erodibility helped to create the emergent steps as the largest particles ( >D84) remained immobile, becoming step features, and downstream soil was easily winnowed away.

Superhydrophobic perfluoropolymer/polystyrene blend films induced by nonsolvent

NASA Astrophysics Data System (ADS)

Gengec, Nevin Atalay; Cengiz, Ugur; Erbil, H. Yildirim

2016-10-01

Statistical copolymers of perfluoroalkyl ethyl acrylate (Zonyl-TAN) and methyl methacrylate (MMA) were synthesized in a CO2 polymerization system where a CO2-expanded monomer mixture was formed at 13 MPa, and 80 °C by using AIBN as initiator. Flat and superhydrophobic surfaces were subsequently prepared on glass slides by applying a phase separation process where the synthesized p(TAN-co-MMA) copolymer and polystyrene (PS) were dissolved in THF solvent. Ethanol was added as the non-solvent to introduce superhydrophobicity during film formation. Water contact angle on the flat p(TAN-co-MMA) copolymer was 118° and increased up to 170° with the formation of surface roughness. The ratio of the ethanol non-solvent in the blend solution has an important effect on the magnitude of surface roughness during the phase separation process. Both pits and protrusions of 1-10 μm in size were formed on the surface when non-solvent was used. Surface roughness increased with the increase in the ethanol ratio and the PS content of the blend solution.

Nanocomposite films

DOEpatents

Mitlin, David; , Ophus, Colin; Evoy, Stephane; Radmilovic, Velimir; Mohammadi, Reza; Westra, Ken; Nelson-Fitzpatrick, Nathaniel; Lee, Zonghoon

2010-07-20

A thin-film composition of nanocrystal molybdenum in an amorphous metallic matrix may be formed by co-sputtering Mo with aluminum or nickel. NEMS cantilevers may be formed from the film. The films exhibit high nanoindentation hardness and a reduction in roughness and intrinsic stress, while maintaining resistivity in the metallic range.

On the role of acoustic feedback in boundary-layer instability.

PubMed

Wu, Xuesong

2014-07-28

In this paper, the classical triple-deck formalism is employed to investigate two instability problems in which an acoustic feedback loop plays an essential role. The first concerns a subsonic boundary layer over a flat plate on which two well-separated roughness elements are present. A spatially amplifying Tollmien-Schlichting (T-S) wave between the roughness elements is scattered by the downstream roughness to emit a sound wave that propagates upstream and impinges on the upstream roughness to regenerate the T-S wave, thereby forming a closed feedback loop in the streamwise direction. Numerical calculations suggest that, at high Reynolds numbers and for moderate roughness heights, the long-range acoustic coupling may lead to absolute instability, which is characterized by self-sustained oscillations at discrete frequencies. The dominant peak frequency may jump from one value to another as the Reynolds number, or the distance between the roughness elements, is varied gradually. The second problem concerns the supersonic 'twin boundary layers' that develop along two well-separated parallel flat plates. The two boundary layers are in mutual interaction through the impinging and reflected acoustic waves. It is found that the interaction leads to a new instability that is absent in the unconfined boundary layer. © 2014 The Author(s) Published by the Royal Society. All rights reserved.

Scaling law governing the roughness of the swash edge line

NASA Astrophysics Data System (ADS)

Bormashenko, E.; Musin, A.; Grynyov, R.

2014-09-01

The paper is devoted to the analysis of the shape of the swash edge line. Formation of the swash boundary is treated as an interfacial phenomenon. The simplest quantitative characteristic of the roughness of interface is its width w, defined as the root-mean-square fluctuation around the average position. For rough interfaces, the scaling with size of the system L is observed in the form w(L)~Lζ. The concept of scaling supplies a simple framework for classifying interfaces. It is suggested that the fine structure of the swash boundary results from the combined action of the pinning force applied by random defects of the beach and elasticity of distorted swash boundary. The roughness of the swash front was studied at the Mediterranean Sea coast for uprush and backwash flows. Value of exponent ζ for receding swash front line was 0.64 +/- 0.02, when in the case of advancing swash the value 0.73 +/- 0.03 was calculated. The scaling exponent established for the receding phase of the swash is very close to the values of the exponent established for the roughness of the triple line for water droplets deposited on rough surfaces, crack propagation front in Plexiglas, and for the motion of a magnetic domain walls.

Modelling NDE pulse-echo inspection of misorientated planar rough defects using an elastic finite element method

NASA Astrophysics Data System (ADS)

Pettit, J. R.; Walker, A. E.; Lowe, M. J. S.

2015-03-01

Pulse-echo ultrasonic NDE examination of large pressure vessel forgings is a design and construction code requirement in the power generation industry. Such inspections aim to size and characterise potential defects that may have formed during the forging process. Typically these defects have a range of orientations and surface roughnesses which can greatly affect ultrasonic wave scattering behaviour. Ultrasonic modelling techniques can provide insight into defect response and therefore aid in characterisation. However, analytical approaches to solving these scattering problems can become inaccurate, especially when applied to increasingly complex defect geometries. To overcome these limitations a elastic Finite Element (FE) method has been developed to simulate pulse-echo inspections of embedded planar defects. The FE model comprises a significantly reduced spatial domain allowing for a Monte-Carlo based approach to consider multiple realisations of defect orientation and surface roughness. The results confirm that defects aligned perpendicular to the path of beam propagation attenuate ultrasonic signals according to the level of surface roughness. However, for defects orientated away from this plane, surface roughness can increase the magnitude of the scattered component propagating back along the path of the incident beam. This study therefore highlights instances where defect roughness increases the magnitude of ultrasonic scattered signals, as opposed to attenuation which is more often assumed.

Investigation of roughing machining simulation by using visual basic programming in NX CAM system

NASA Astrophysics Data System (ADS)

Hafiz Mohamad, Mohamad; Nafis Osman Zahid, Muhammed

2018-03-01

This paper outlines a simulation study to investigate the characteristic of roughing machining simulation in 4th axis milling processes by utilizing visual basic programming in NX CAM systems. The selection and optimization of cutting orientation in rough milling operation is critical in 4th axis machining. The main purpose of roughing operation is to approximately shape the machined parts into finished form by removing the bulk of material from workpieces. In this paper, the simulations are executed by manipulating a set of different cutting orientation to generate estimated volume removed from the machine parts. The cutting orientation with high volume removal is denoted as an optimum value and chosen to execute a roughing operation. In order to run the simulation, customized software is developed to assist the routines. Operations build-up instructions in NX CAM interface are translated into programming codes via advanced tool available in the Visual Basic Studio. The codes is customized and equipped with decision making tools to run and control the simulations. It permits the integration with any independent program files to execute specific operations. This paper aims to discuss about the simulation program and identifies optimum cutting orientations for roughing processes. The output of this study will broaden up the simulation routines performed in NX CAM systems.

Granularity refined by knowledge: contingency tables and rough sets as tools of discovery

NASA Astrophysics Data System (ADS)

Zytkow, Jan M.

2000-04-01

Contingency tables represent data in a granular way and are a well-established tool for inductive generalization of knowledge from data. We show that the basic concepts of rough sets, such as concept approximation, indiscernibility, and reduct can be expressed in the language of contingency tables. We further demonstrate the relevance to rough sets theory of additional probabilistic information available in contingency tables and in particular of statistical tests of significance and predictive strength applied to contingency tables. Tests of both type can help the evaluation mechanisms used in inductive generalization based on rough sets. Granularity of attributes can be improved in feedback with knowledge discovered in data. We demonstrate how 49er's facilities for (1) contingency table refinement, for (2) column and row grouping based on correspondence analysis, and (3) the search for equivalence relations between attributes improve both granularization of attributes and the quality of knowledge. Finally we demonstrate the limitations of knowledge viewed as concept approximation, which is the focus of rough sets. Transcending that focus and reorienting towards the predictive knowledge and towards the related distinction between possible and impossible (or statistically improbable) situations will be very useful in expanding the rough sets approach to more expressive forms of knowledge.

Flow characteristics of an inclined air-curtain range hood in a draft

PubMed Central

CHEN, Jia-Kun

2015-01-01

The inclined air-curtain technology was applied to build an inclined air-curtain range hood. A draft generator was applied to affect the inclined air-curtain range hood in three directions: lateral (θ=0°), oblique (θ=45°), and front (θ=90°). The three suction flow rates provided by the inclined air-curtain range hood were 10.1, 10.9, and 12.6 m3/min. The laser-assisted flow visualization technique and the tracer-gas test method were used to investigate the performance of the range hood under the influence of a draft. The results show that the inclined air-curtain range hood has a strong ability to resist the negative effect of a front draft until the draft velocity is greater than 0.5 m/s. The oblique draft affected the containment ability of the inclined air-curtain range hood when the draft velocity was larger than 0.3 m/s. When the lateral draft effect was applied, the capture efficiency of the inclined air-curtain range hood decreased quickly in the draft velocity from 0.2 m/s to 0.3 m/s. However, the capture efficiencies of the inclined air-curtain range hood under the influence of the front draft were higher than those under the influence of the oblique draft from 0.3 m/s to 0.5 m/s. PMID:25810445

Flow characteristics of an inclined air-curtain range hood in a draft.

PubMed

Chen, Jia-Kun

2015-01-01

The inclined air-curtain technology was applied to build an inclined air-curtain range hood. A draft generator was applied to affect the inclined air-curtain range hood in three directions: lateral (θ=0°), oblique (θ=45°), and front (θ=90°). The three suction flow rates provided by the inclined air-curtain range hood were 10.1, 10.9, and 12.6 m(3)/min. The laser-assisted flow visualization technique and the tracer-gas test method were used to investigate the performance of the range hood under the influence of a draft. The results show that the inclined air-curtain range hood has a strong ability to resist the negative effect of a front draft until the draft velocity is greater than 0.5 m/s. The oblique draft affected the containment ability of the inclined air-curtain range hood when the draft velocity was larger than 0.3 m/s. When the lateral draft effect was applied, the capture efficiency of the inclined air-curtain range hood decreased quickly in the draft velocity from 0.2 m/s to 0.3 m/s. However, the capture efficiencies of the inclined air-curtain range hood under the influence of the front draft were higher than those under the influence of the oblique draft from 0.3 m/s to 0.5 m/s.

The influence of interfacial slip on two-phase flow in rough pores

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kucala, Alec; Martinez, Mario J.; Wang, Yifeng

The migration and trapping of supercritical CO 2 (scCO 2) in geologic carbon storage is strongly dependent on the geometry and wettability of the pore network in the reservoir rock. During displacement, resident fluids may become trapped in the pits of a rough pore surface forming an immiscible two-phase fluid interface with the invading fluid, allowing apparent slip flow at this interface. We present a two-phase fluid dynamics model, including interfacial tension, to characterize the impact of mineral surface roughness on this slip flow. We show that the slip flow can be cast in more familiar terms as a contact-anglemore » (wettability)-dependent effective permeability to the invading fluid, a nondimensional measurement which relates the interfacial slip to the pore geometry. The analysis shows the surface roughness-induced slip flow can effectively increase or decrease this effective permeability, depending on the wettability and roughness of the mineral surfaces. Configurations of the pore geometry where interfacial slip has a tangible influence on permeability have been identified. The results suggest that for large roughness features, permeability to CO 2 may be enhanced by approximately 30% during drainage, while the permeability to brine during reimbibition may be enhanced or diminished by 60%, depending on the contact angle with the mineral surfaces and degrees of roughness. For smaller roughness features, the changes in permeability through interfacial slip are small. As a result, a much larger range of effective permeabilities are suggested for general fluid pairs and contact angles, including occlusion of the pore by the trapped phase.« less

The influence of interfacial slip on two-phase flow in rough pores

DOE PAGES

Kucala, Alec; Martinez, Mario J.; Wang, Yifeng; ...

2017-08-01

The migration and trapping of supercritical CO 2 (scCO 2) in geologic carbon storage is strongly dependent on the geometry and wettability of the pore network in the reservoir rock. During displacement, resident fluids may become trapped in the pits of a rough pore surface forming an immiscible two-phase fluid interface with the invading fluid, allowing apparent slip flow at this interface. We present a two-phase fluid dynamics model, including interfacial tension, to characterize the impact of mineral surface roughness on this slip flow. We show that the slip flow can be cast in more familiar terms as a contact-anglemore » (wettability)-dependent effective permeability to the invading fluid, a nondimensional measurement which relates the interfacial slip to the pore geometry. The analysis shows the surface roughness-induced slip flow can effectively increase or decrease this effective permeability, depending on the wettability and roughness of the mineral surfaces. Configurations of the pore geometry where interfacial slip has a tangible influence on permeability have been identified. The results suggest that for large roughness features, permeability to CO 2 may be enhanced by approximately 30% during drainage, while the permeability to brine during reimbibition may be enhanced or diminished by 60%, depending on the contact angle with the mineral surfaces and degrees of roughness. For smaller roughness features, the changes in permeability through interfacial slip are small. As a result, a much larger range of effective permeabilities are suggested for general fluid pairs and contact angles, including occlusion of the pore by the trapped phase.« less

The influence of interfacial slip on two-phase flow in rough pores

NASA Astrophysics Data System (ADS)

Kucala, Alec; Martinez, Mario J.; Wang, Yifeng; Noble, David R.

2017-08-01

The migration and trapping of supercritical CO2 (scCO2) in geologic carbon storage is strongly dependent on the geometry and wettability of the pore network in the reservoir rock. During displacement, resident fluids may become trapped in the pits of a rough pore surface forming an immiscible two-phase fluid interface with the invading fluid, allowing apparent slip flow at this interface. We present a two-phase fluid dynamics model, including interfacial tension, to characterize the impact of mineral surface roughness on this slip flow. We show that the slip flow can be cast in more familiar terms as a contact-angle (wettability)-dependent effective permeability to the invading fluid, a nondimensional measurement which relates the interfacial slip to the pore geometry. The analysis shows the surface roughness-induced slip flow can effectively increase or decrease this effective permeability, depending on the wettability and roughness of the mineral surfaces. Configurations of the pore geometry where interfacial slip has a tangible influence on permeability have been identified. The results suggest that for large roughness features, permeability to CO2 may be enhanced by approximately 30% during drainage, while the permeability to brine during reimbibition may be enhanced or diminished by 60%, depending on the contact angle with the mineral surfaces and degrees of roughness. For smaller roughness features, the changes in permeability through interfacial slip are small. A much larger range of effective permeabilities are suggested for general fluid pairs and contact angles, including occlusion of the pore by the trapped phase.

SPH modelling of depth-limited turbulent open channel flows over rough boundaries.

PubMed

Kazemi, Ehsan; Nichols, Andrew; Tait, Simon; Shao, Songdong

2017-01-10

A numerical model based on the smoothed particle hydrodynamics method is developed to simulate depth-limited turbulent open channel flows over hydraulically rough beds. The 2D Lagrangian form of the Navier-Stokes equations is solved, in which a drag-based formulation is used based on an effective roughness zone near the bed to account for the roughness effect of bed spheres and an improved sub-particle-scale model is applied to account for the effect of turbulence. The sub-particle-scale model is constructed based on the mixing-length assumption rather than the standard Smagorinsky approach to compute the eddy-viscosity. A robust in/out-flow boundary technique is also proposed to achieve stable uniform flow conditions at the inlet and outlet boundaries where the flow characteristics are unknown. The model is applied to simulate uniform open channel flows over a rough bed composed of regular spheres and validated by experimental velocity data. To investigate the influence of the bed roughness on different flow conditions, data from 12 experimental tests with different bed slopes and uniform water depths are simulated, and a good agreement has been observed between the model and experimental results of the streamwise velocity and turbulent shear stress. This shows that both the roughness effect and flow turbulence should be addressed in order to simulate the correct mechanisms of turbulent flow over a rough bed boundary and that the presented smoothed particle hydrodynamics model accomplishes this successfully. © 2016 The Authors International Journal for Numerical Methods in Fluids Published by John Wiley & Sons Ltd.

75 FR 21145 - Availability of the Draft Environmental Impact Statement

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-22

... DEPARTMENT OF TRANSPORTATION Federal Highway Administration Availability of the Draft... availability of the Draft Environmental Impact Statement. SUMMARY: The FHWA, on behalf of the California Department of Transportation (Caltrans), announces the availability of the Draft Environmental Impact...

Evaluation of scintillometery measurements of fluxes of momentum and sensible heat in the roughness sublayer

NASA Astrophysics Data System (ADS)

Sugawara, Hirofumi; Inagaki, Atsushi; Roth, Matthias; Kanda, Manabu

2016-11-01

Scintillometer measurements of turbulent fluxes of momentum and sensible heat in the roughness sublayer over a regular array of cubes in an outdoor environment were tested with direct measurement from sonic anemometers. The dissipation rate, ɛ, and temperature structure parameter, C T 2 , obtained from the scintillometer agreed well with those from four sonic anemometers located along the scintillometer path. The fluxes measured by the scintillometer also corresponded well to those from the line-averaged eddy covariance approach, although this agreement was greatly influenced by the choice of the zero-plane displacement length and the form of the similarity function used in the scintillometer software. A guide for choosing the appropriate similarity function for the urban roughness sublayer is proposed.

First-Year Student Experiences in Community College: Making Transitions, Forming Connections, and Developing Perceptions of Student Learning. Draft.

ERIC Educational Resources Information Center

Jalomo, Romero Espinoza, Jr.

This paper provides theoretical background and methodology for a focus group study of influences on first-time Latino community college students. The first chapter identifies the need for research on Latino students, citing high attrition rates and focusing on three critical dynamics: making the transition to college, making connections on campus…

76 FR 10072 - Proposed Generic Communications; Draft NRC Regulatory Issue Summary 2011-XX, Adequacy of Station...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-23

... electronic form will be posted on the NRC Web site and on the Federal Rulemaking Web site Regulations.gov... that they do not want publicly disclosed. Federal rulemaking Web site: Go to http://www.regulations.gov... through this Web site. Address questions about NRC dockets to Carol Gallagher, telephone: 301-492-3668, e...

22 CFR 22.3 - Remittances in the United States.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Remittances in the United States. 22.3 Section...-DEPARTMENT OF STATE AND FOREIGN SERVICE § 22.3 Remittances in the United States. (a) Type of remittance. Remittances shall be in the form of: (1) Check or bank draft drawn on a bank in the United States; (2) money...

22 CFR 22.3 - Remittances in the United States.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 22 Foreign Relations 1 2013-04-01 2013-04-01 false Remittances in the United States. 22.3 Section...-DEPARTMENT OF STATE AND FOREIGN SERVICE § 22.3 Remittances in the United States. (a) Type of remittance. Remittances shall be in the form of: (1) Check or bank draft drawn on a bank in the United States; (2) money...

A comprehensive draft genome sequence for lupin (Lupinus angustifolius), an emerging health food: Insights into plant-microbe interactions and legume evolution

USDA-ARS?s Scientific Manuscript database

Lupins are important grain legume crops that form a critical part of sustainable farming systems, by reducing the need for fertilizer and providing disease breaks. Narrow-leafed lupin (Lupinus angustifolius L.) is gaining popularity as a human health food, as a non-GM alternative to soybean with the...

76 FR 54195 - 2010 Resources Planning Act (RPA) Assessment Draft

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-31

... Resources Planning Act (RPA) Assessment is available for review and comment at http://www.fs.fed.us/research... facsimile to 703-605-5131 or by email using the comment form on the Web site http://www.fs.fed.us/research... . Additional information about the RPA Assessment can be obtained on the Internet at http://www.fs.fed.us...

75 FR 39852 - Emergency Planning and Community Right-to-Know Act; Guidance on Reporting Options for Sections...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-13

... hazardous substances (EHSs) and to provide the public, local agencies, fire departments, and other emergency... submitted to the SERC, LEPC and the local fire department. The implementing regulations for sections 311 and... burden for SERCs, LEPCs and fire departments in the form of draft guidance in the preamble to the June 8...

High-quality permanent draft genome sequence of the Bradyrhizobium elkanii type strain USDA 76T, isolated from Glycine max (L.) Merr

USDA-ARS?s Scientific Manuscript database

Bradyrhizobium elkanii USDA 76T (INSCD = ARAG00000000), the type strain for Bradyrhizobium elkanii, is an aerobic, motile, Gram-negative, non-spore-forming rod that was isolated from an effective nitrogen-fixing root nodule of Glycine max (L. Merr) grown in the USA. Because of its significance as a ...

Developing a Peace and Conflict Resolution Curriculum for Quaker Secondary Schools in Kenya

ERIC Educational Resources Information Center

Hockett, Eloise

2012-01-01

In 2008-2009, a team of educators from George Fox University, in collaboration with a committee of teachers and administrators from selected Quaker secondary schools in western Kenya, developed the first draft of a peace and conflict resolution curriculum for Kenyan form one (ninth grade) students. This case study offers a model for developing a…

Meeting Materials for the 4th NRC Meeting on the Guidance for and the Review of EPA's Toxicological Assessment of Inorganic Arsenic

EPA Science Inventory

On December 2-3, 2015, the National Research Council (NRC) hosted the 4th meeting of the committee formed to peer review the draft IRIS assessment of inorganic arsenic. EPA presented background and overview materials during the public session on December 2nd. This information co...

Working with WebQuests: Making the Web Accessible to Students with Disabilities.

ERIC Educational Resources Information Center

Kelly, Rebecca

2000-01-01

This article describes how students with disabilities in regular classes are using the WebQuest lesson format to access the Internet. It explains essential WebQuest principles, creating a draft Web page, and WebQuest components. It offers an example of a WebQuest about salvaging the sunken ships, Titanic and Lusitania. A WebQuest planning form is…

High-quality permanent draft genome sequence of Ensifer sp. PC2, isolated from a nitrogen-fixing root nodule of the legume tree (Khejri) native to the Thar Desert of India

DOE PAGES

Gehlot, Hukam Singh; Ardley, Julie; Tak, Nisha; ...

2016-06-23

Ensifer sp. PC2 is an aerobic, motile, Gram-negative, non-spore-forming rod that was isolated from a nitrogen-fixing nodule of the tree legume P. cineraria (L.) Druce (Khejri), which is a keystone species that grows in arid and semi-arid regions of the Indian Thar desert. Strain PC2 exists as a dominant saprophyte in alkaline soils of Western Rajasthan. It is fast growing, well-adapted to arid conditions and is able to form an effective symbiosis with several annual crop legumes as well as species of mimosoid trees and shrubs. Here we describe the features of Ensifer sp. PC2, together with genome sequence informationmore » and its annotation. The 8,458,965 bp high-quality permanent draft genome is arranged into 171 scaffolds of 171 contigs containing 8,344 protein-coding genes and 139 RNA-only encoding genes, and is one of the rhizobial genomes sequenced as part of the DOE Joint Genome Institute 2010 Genomic Encyclopedia for Bacteria and Archaea-Root Nodule Bacteria (GEBA-RNB) project proposal.« less

High-quality permanent draft genome sequence of Ensifer sp. PC2, isolated from a nitrogen-fixing root nodule of the legume tree (Khejri) native to the Thar Desert of India

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gehlot, Hukam Singh; Ardley, Julie; Tak, Nisha

Ensifer sp. PC2 is an aerobic, motile, Gram-negative, non-spore-forming rod that was isolated from a nitrogen-fixing nodule of the tree legume P. cineraria (L.) Druce (Khejri), which is a keystone species that grows in arid and semi-arid regions of the Indian Thar desert. Strain PC2 exists as a dominant saprophyte in alkaline soils of Western Rajasthan. It is fast growing, well-adapted to arid conditions and is able to form an effective symbiosis with several annual crop legumes as well as species of mimosoid trees and shrubs. Here we describe the features of Ensifer sp. PC2, together with genome sequence informationmore » and its annotation. The 8,458,965 bp high-quality permanent draft genome is arranged into 171 scaffolds of 171 contigs containing 8,344 protein-coding genes and 139 RNA-only encoding genes, and is one of the rhizobial genomes sequenced as part of the DOE Joint Genome Institute 2010 Genomic Encyclopedia for Bacteria and Archaea-Root Nodule Bacteria (GEBA-RNB) project proposal.« less

75 FR 3760 - Draft Regulatory Guide: Issuance, Availability

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-22

... NUCLEAR REGULATORY COMMISSION [NRC-2010-0018] Draft Regulatory Guide: Issuance, Availability AGENCY: Nuclear Regulatory Commission. ACTION: Notice of Issuance and Availability of Draft Regulatory...) is issuing for public comment a draft guide in the agency's ``Regulatory Guide'' series. This series...

75 FR 20645 - Draft Regulatory Guide: Issuance, Availability

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-20

... NUCLEAR REGULATORY COMMISSION [NRC-2010-0158] Draft Regulatory Guide: Issuance, Availability AGENCY: Nuclear Regulatory Commission. ACTION: Notice of Issuance and Availability of Draft Regulatory... draft guide in the agency's ``Regulatory Guide'' series. This series was developed to describe and make...

77 FR 33489 - Draft Offender Tracking System Standard

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-06

... Tracking System Standard AGENCY: National Institute of Justice. ACTION: Notice of Draft Offender Tracking System Standard, Selection and Application Guide, and Certification Program Requirements. SUMMARY: In an...) A draft standard entitled, ``Offender Tracking System Standard'' (2) a draft companion document...

Rough and smooth morphotypes isolated from Lactobacillus farciminis CNCM I-3699 are two closely-related variants.

PubMed

Tareb, Raouf; Bernardeau, Marion; Horvath, Philippe; Vernoux, Jean-Paul

2015-01-16

This study focused on a pleomorphic strain Lactobacillus farciminis CNCM I-3699 known as probiotic for animal applications. On plating, this strain was characterized by the presence of rough and smooth morphotypes depending on experimental conditions. Dominant smooth (S) form, bright white, having smooth edges with moist, ropy, and creamy along with rough (R) form, pale white, having irregular edges and a dry and granular aspect were always obtained from the parent strain under aerobic culture conditions. In anaerobic conditions, only S form growth was observed. Biochemical dosage of capsular exopolysaccharides showed a significant difference between S and R forms (p<0.01), in agreement with a ropy or non ropy phenotype for the S or R form, respectively. These differences were confirmed by transmission electronic microscopy. The auto-aggregation profile revealed major differences in cultural behaviors. The R morphotype presented a highly auto-aggregative ability contrary to the S morphotype. However, biochemical and molecular analyses revealed that R and S morphotypes: 1) shared the same sugar fermentation pattern; 2) belonged to L. farciminis species using 16S rDNA sequencing; 3) had identical PFGE patterns using NotI and ApaI endonucleases; and 4) had identical CRISPR loci but different from those of other L. farciminis strains. Furthermore, the novelty and uniqueness of CRISPR spacer sequences in CNCM I-3699 provides a genetic support for the development of a molecular tracking tool for CNCM I-3699 and its variants. In conclusion, L. farciminis CNCM I-3699 is a pleomorphic strain giving reproducibly rise to two phenotypically distinct morphotypes R and S. This phenomenon may explain survival and growth abilities in in vitro fluctuating aerobic-anaerobic conditions along with modulation of exopolysaccharide synthesis and autoaggregation profile. Copyright © 2014 Elsevier B.V. All rights reserved.

Characterization of the coating and tablet core roughness by means of 3D optical coherence tomography.

PubMed

Markl, Daniel; Wahl, Patrick; Pichler, Heinz; Sacher, Stephan; Khinast, Johannes G

2018-01-30

This study demonstrates the use of optical coherence tomography (OCT) to simultaneously characterize the roughness of the tablet core and coating of pharmaceutical tablets. OCT is a high resolution non-destructive and contactless imaging methodology to characterize structural properties of solid dosage forms. Besides measuring the coating thickness, it also facilitates the analysis of the tablet core and coating roughness. An automated data evaluation algorithm extracts information about coating thickness, as well as tablet core and coating roughness. Samples removed periodically from a pan coating process were investigated, on the basis of thickness and profile maps of the tablet core and coating computed from about 480,000 depth measurements (i.e., 3D data) per sample. This data enables the calculation of the root mean square deviation, the skewness and the kurtosis of the assessed profiles. Analyzing these roughness parameters revealed that, for the given coating formulation, small valleys in the tablet core are filled with coating, whereas coarse features of the tablet core are still visible on the final film-coated tablet. Moreover, the impact of the tablet core roughness on the coating thickness is analyzed by correlating the tablet core profile and the coating thickness map. The presented measurement method and processing could be in the future transferred to in-line OCT measurements, to investigate core and coating roughness during the production of film-coated tablets. Copyright © 2017. Published by Elsevier B.V.

Study of the velocity distribution influence upon the pressure pulsations in draft tube model of hydro-turbine

NASA Astrophysics Data System (ADS)

Sonin, V.; Ustimenko, A.; Kuibin, P.; Litvinov, I.; Shtork, S.

2016-11-01

One of the mechanisms of generation of powerful pressure pulsations in the circuit of the turbine is a precessing vortex core, formed behind the runner at the operation points with partial or forced loads, when the flow has significant residual swirl. To study periodic pressure pulsations behind the runner the authors of this paper use approaches of experimental modeling and methods of computational fluid dynamics. The influence of velocity distributions at the output of the hydro turbine runner on pressure pulsations was studied based on analysis of the existing and possible velocity distributions in hydraulic turbines and selection of the distribution in the extended range. Preliminary numerical calculations have showed that the velocity distribution can be modeled without reproduction of the entire geometry of the circuit, using a combination of two blade cascades of the rotor and stator. Experimental verification of numerical results was carried out in an air bench, using the method of 3D-printing for fabrication of the blade cascades and the geometry of the draft tube of hydraulic turbine. Measurements of the velocity field at the input to a draft tube cone and registration of pressure pulsations due to precessing vortex core have allowed building correlations between the velocity distribution character and the amplitude-frequency characteristics of the pulsations.

IRIS Toxicological Review of Methanol (Noncancer) (Interagency Science Discussion Draft)

EPA Science Inventory

On May 3, 2013, the Toxicological Review of Methanol (noncancer) (Revised External Review Draft) was posted for public review and comment. Subsequently, the draft Toxicological Review, Appendices, and draft IRIS Summary were reviewed internally by EPA and by other federal agenci...

75 FR 48973 - Draft Guidance for Industry: Prevention of Salmonella

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-12

...] Draft Guidance for Industry: Prevention of Salmonella Enteritidis in Shell Eggs During Production... entitled ``Prevention of Salmonella Enteritidis in Shell Eggs During Production, Storage, and Transportation'' (the draft guidance). The draft guidance, when finalized, will provide guidance to egg producers...

Competency Reference for Computer Assisted Drafting.

ERIC Educational Resources Information Center

Oregon State Dept. of Education, Salem. Div. of Vocational Technical Education.

This guide, developed in Oregon, lists competencies essential for students in computer-assisted drafting (CAD). Competencies are organized in eight categories: computer hardware, file usage and manipulation, basic drafting techniques, mechanical drafting, specialty disciplines, three dimensional drawing/design, plotting/printing, and advanced CAD.…

31 CFR 515.405 - Exportation of securities, currency, checks, drafts and promissory notes.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., checks, drafts and promissory notes. 515.405 Section 515.405 Money and Finance: Treasury Regulations..., drafts and promissory notes. Section 515.201 prohibits the exportation of securities, currency, checks, drafts and promissory notes to a designated foreign country. ...

31 CFR 515.405 - Exportation of securities, currency, checks, drafts and promissory notes.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., checks, drafts and promissory notes. 515.405 Section 515.405 Money and Finance: Treasury Regulations..., drafts and promissory notes. Section 515.201 prohibits the exportation of securities, currency, checks, drafts and promissory notes to a designated foreign country. ...

75 FR 18241 - Draft Regulatory Guide: Issuance, Availability

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-09

... NUCLEAR REGULATORY COMMISSION [NRC-2010-0148] Draft Regulatory Guide: Issuance, Availability AGENCY: Nuclear Regulatory Commission. ACTION: Notice of Issuance and Availability of Draft Regulatory.... Introduction The U.S. Nuclear Regulatory Commission (NRC) is issuing for public comment a draft guide in the...

31 CFR 515.405 - Exportation of securities, currency, checks, drafts and promissory notes.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., checks, drafts and promissory notes. 515.405 Section 515.405 Money and Finance: Treasury Regulations..., drafts and promissory notes. Section 515.201 prohibits the exportation of securities, currency, checks, drafts and promissory notes to a designated foreign country. ...

31 CFR 515.405 - Exportation of securities, currency, checks, drafts and promissory notes.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., checks, drafts and promissory notes. 515.405 Section 515.405 Money and Finance: Treasury Regulations..., drafts and promissory notes. Section 515.201 prohibits the exportation of securities, currency, checks, drafts and promissory notes to a designated foreign country. ...

31 CFR 515.405 - Exportation of securities, currency, checks, drafts and promissory notes.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., checks, drafts and promissory notes. 515.405 Section 515.405 Money and Finance: Treasury Regulations..., drafts and promissory notes. Section 515.201 prohibits the exportation of securities, currency, checks, drafts and promissory notes to a designated foreign country. ...

75 FR 45166 - Draft Regulatory Guide: Issuance, Availability

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-02

... NUCLEAR REGULATORY COMMISSION [NRC-2010-0265] Draft Regulatory Guide: Issuance, Availability AGENCY: Nuclear Regulatory Commission. ACTION: Notice of Issuance and Availability of Draft Regulatory.... Introduction The U.S. Nuclear Regulatory Commission (NRC) is issuing for public comment a draft guide in the...

76 FR 6086 - Draft Regulatory Guide: Issuance, Availability

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-03

... NUCLEAR REGULATORY COMMISSION 10 CFR Part 73 [NRC-2011-0015] RIN 3150-AI49 Draft Regulatory Guide: Issuance, Availability AGENCY: Nuclear Regulatory Commission. ACTION: Notice of Availability of Draft... comment Draft Regulatory Guide, DG-5020, ``Applying for Enhanced Weapons Authority, Applying for...

76 FR 13436 - NIJ Request for Comments on Draft Vehicular Digital Multimedia Evidence Recording System...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-11

... Comments on Draft Vehicular Digital Multimedia Evidence Recording System Certification Program Requirements for Law Enforcement and Draft Law Enforcement Vehicular Digital Multimedia Evidence Recording System... two draft documents: ``Vehicular Digital Multimedia Evidence Recording System Certification Program...

78 FR 77027 - Overhead Clearance (Air-Draft) Accidents

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-20

... No. USCG-2013-0466] Overhead Clearance (Air-Draft) Accidents AGENCY: Coast Guard, DHS. ACTION... clearance (air-draft) accidents. In its petition, which calls for vessel masters to be provided with accurate vertical air draft information, a maritime organization has described 16 overhead clearance...

75 FR 63188 - Draft Guidance for Industry: Early Clinical Trials With Live Biotherapeutic Products: Chemistry...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-14

...] Draft Guidance for Industry: Early Clinical Trials With Live Biotherapeutic Products: Chemistry...: Chemistry, Manufacturing, and Control Information'' dated September 2010. The draft guidance provides... Products: Chemistry, Manufacturing, and Control Information'' dated September 2010. The draft guidance...

10 CFR 51.85 - Draft environmental impact statement-rulemaking.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Draft environmental impact statement-rulemaking. 51.85... Implementing Section 102(2) Draft Environmental Impact Statements-Rulemaking § 51.85 Draft environmental impact... Commission has determined to prepare an environmental impact statement. ...

Effects of Fault Segmentation, Mechanical Interaction, and Structural Complexity on Earthquake-Generated Deformation

NASA Astrophysics Data System (ADS)

Haddad, David Elias

Earth's topographic surface forms an interface across which the geodynamic and geomorphic engines interact. This interaction is best observed along crustal margins where topography is created by active faulting and sculpted by geomorphic processes. Crustal deformation manifests as earthquakes at centennial to millennial timescales. Given that nearly half of Earth's human population lives along active fault zones, a quantitative understanding of the mechanics of earthquakes and faulting is necessary to build accurate earthquake forecasts. My research relies on the quantitative documentation of the geomorphic expression of large earthquakes and the physical processes that control their spatiotemporal distributions. The first part of my research uses high-resolution topographic lidar data to quantitatively document the geomorphic expression of historic and prehistoric large earthquakes. Lidar data allow for enhanced visualization and reconstruction of structures and stratigraphy exposed by paleoseismic trenches. Lidar surveys of fault scarps formed by the 1992 Landers earthquake document the centimeter-scale erosional landforms developed by repeated winter storm-driven erosion. The second part of my research employs a quasi-static numerical earthquake simulator to explore the effects of fault roughness, friction, and structural complexities on earthquake-generated deformation. My experiments show that fault roughness plays a critical role in determining fault-to-fault rupture jumping probabilities. These results corroborate the accepted 3-5 km rupture jumping distance for smooth faults. However, my simulations show that the rupture jumping threshold distance is highly variable for rough faults due to heterogeneous elastic strain energies. Furthermore, fault roughness controls spatiotemporal variations in slip rates such that rough faults exhibit lower slip rates relative to their smooth counterparts. The central implication of these results lies in guiding the interpretation of paleoseismically derived slip rates that are used to form earthquake forecasts. The final part of my research evaluates a set of Earth science-themed lesson plans that I designed for elementary-level learning-disabled students. My findings show that a combination of concept delivery techniques is most effective for learning-disabled students and should incorporate interactive slide presentations, tactile manipulatives, teacher-assisted concept sketches, and student-led teaching to help learning-disabled students grasp Earth science concepts.

A State Articulated Instructional Objectives Guide for Occupational Education Programs. State Pilot Model for Drafting (Graphic Communications). Part I--Basic. Part II--Specialty Programs. Section A (Mechanical Drafting and Design). Section B (Architectural Drafting and Design).

ERIC Educational Resources Information Center

North Carolina State Dept. of Community Colleges, Raleigh.

A two-part articulation instructional objective guide for drafting (graphic communications) is provided. Part I contains summary information on seven blocks (courses) of instruction. They are as follow: introduction; basic technical drafting; problem solving in graphics; reproduction processes; freehand drawing and sketching; graphics composition;…

A genome sequence resource for the aye-aye (Daubentonia madagascariensis), a nocturnal lemur from Madagascar.

PubMed

Perry, George H; Reeves, Darryl; Melsted, Páll; Ratan, Aakrosh; Miller, Webb; Michelini, Katelyn; Louis, Edward E; Pritchard, Jonathan K; Mason, Christopher E; Gilad, Yoav

2012-01-01

We present a high-coverage draft genome assembly of the aye-aye (Daubentonia madagascariensis), a highly unusual nocturnal primate from Madagascar. Our assembly totals ~3.0 billion bp (3.0 Gb), roughly the size of the human genome, comprised of ~2.6 million scaffolds (N50 scaffold size = 13,597 bp) based on short paired-end sequencing reads. We compared the aye-aye genome sequence data with four other published primate genomes (human, chimpanzee, orangutan, and rhesus macaque) as well as with the mouse and dog genomes as nonprimate outgroups. Unexpectedly, we observed strong evidence for a relatively slow substitution rate in the aye-aye lineage compared with these and other primates. In fact, the aye-aye branch length is estimated to be ~10% shorter than that of the human lineage, which is known for its low substitution rate. This finding may be explained, in part, by the protracted aye-aye life-history pattern, including late weaning and age of first reproduction relative to other lemurs. Additionally, the availability of this draft lemur genome sequence allowed us to polarize nucleotide and protein sequence changes to the ancestral primate lineage-a critical period in primate evolution, for which the relevant fossil record is sparse. Finally, we identified 293,800 high-confidence single nucleotide polymorphisms in the donor individual for our aye-aye genome sequence, a captive-born individual from two wild-born parents. The resulting heterozygosity estimate of 0.051% is the lowest of any primate studied to date, which is understandable considering the aye-aye's extensive home-range size and relatively low population densities. Yet this level of genetic diversity also suggests that conservation efforts benefiting this unusual species should be prioritized, especially in the face of the accelerating degradation and fragmentation of Madagascar's forests.

78 FR 56718 - Draft Guidance for Industry on Bioanalytical Method Validation; Availability

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-13

...] Draft Guidance for Industry on Bioanalytical Method Validation; Availability AGENCY: Food and Drug... availability of a draft guidance for industry entitled ``Bioanalytical Method Validation.'' The draft guidance is intended to provide recommendations regarding analytical method development and validation for the...

General Drafting. Technical Manual.

ERIC Educational Resources Information Center

Department of the Army, Washington, DC.

The manual provides instructional guidance and reference material in the principles and procedures of general drafting and constitutes the primary study text for personnel in drafting as a military occupational specialty. Included is information on drafting equipment and its use; line weights, conventions and formats; lettering; engineering charts…

Basic Drafting. Revised.

ERIC Educational Resources Information Center

Schertz, Karen

This introductory module on drafting includes the technical content and tasks necessary for a student to be employed in an entry-level drafting occupation. The module contains 18 instructional units that cover the following topics: introduction to drafting; tools and equipment; supplies and materials; sketching; scales; drawing format; lettering;…

10 CFR 51.85 - Draft environmental impact statement-rulemaking.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 2 2013-01-01 2013-01-01 false Draft environmental impact statement-rulemaking. 51.85 Section 51.85 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) ENVIRONMENTAL PROTECTION REGULATIONS FOR... Implementing Section 102(2) Draft Environmental Impact Statements-Rulemaking § 51.85 Draft environmental impact...

10 CFR 51.85 - Draft environmental impact statement-rulemaking.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 2 2011-01-01 2011-01-01 false Draft environmental impact statement-rulemaking. 51.85 Section 51.85 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) ENVIRONMENTAL PROTECTION REGULATIONS FOR... Implementing Section 102(2) Draft Environmental Impact Statements-Rulemaking § 51.85 Draft environmental impact...

10 CFR 51.85 - Draft environmental impact statement-rulemaking.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 2 2014-01-01 2014-01-01 false Draft environmental impact statement-rulemaking. 51.85 Section 51.85 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) ENVIRONMENTAL PROTECTION REGULATIONS FOR... Implementing Section 102(2) Draft Environmental Impact Statements-Rulemaking § 51.85 Draft environmental impact...

10 CFR 51.85 - Draft environmental impact statement-rulemaking.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 2 2012-01-01 2012-01-01 false Draft environmental impact statement-rulemaking. 51.85 Section 51.85 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) ENVIRONMENTAL PROTECTION REGULATIONS FOR... Implementing Section 102(2) Draft Environmental Impact Statements-Rulemaking § 51.85 Draft environmental impact...

76 FR 6085 - Draft Regulatory Guide: Issuance, Availability

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-03

...-2011-0014] RIN 3150-AI49 Draft Regulatory Guide: Issuance, Availability AGENCY: Nuclear Regulatory Commission. ACTION: Notice Availability of Draft Regulatory Guide. SUMMARY: The U.S. Nuclear Regulatory Commission (Commission or NRC) is issuing for public comment Draft Regulatory Guide, DG-5019, ``Reporting and...

78 FR 17653 - Upper Great Plains Wind Energy Draft Programmatic Environmental Impact Statement (DOE/EIS-0408)

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-22

... infrastructure development, including siting wind turbines, access roads, underground collector lines, overhead... Wildlife Service Upper Great Plains Wind Energy Draft Programmatic Environmental Impact Statement (DOE/EIS... Plains Wind Energy Draft Programmatic Environmental Impact Statement (Draft [[Page 17654

Controls on the extent of sediment cover in bedrock-alluvial channels

NASA Astrophysics Data System (ADS)

Hodge, Rebecca; Johnson, Joel; Tranmer, Andy; Yager, Elowyn

2017-04-01

The amount and location of sediment cover in a bedrock-alluvial channel is a key factor that controls the morphological evolution of the channel, sediment transport pathways and channel roughness. The amount of sediment cover is often predicted as a function of relative sediment supply (sediment supply over transport capacity). However, several different forms of this relationship have been produced using a range of different approaches, and there is not yet agreement as to the controlling factors that need to be included. Part of this lack of agreement is because of the need for a more processed-based understanding of the way in which sediment cover is formed and eroded in bedrock-alluvial channels. We start to address this knowledge gap by assessing the factors that control the location of sediment cover in a field setting. We present field data from two channels in the Henry Mountains, USA. The field data includes measurement of channel geometry, slope, sediment cover location, bedrock roughness, grain size and boulder occurrence. Relative sediment supply is estimated by assuming that downstream changes are primarily accounted for by changes in transport capacity, rather than sediment supply. Preliminary results suggest that there is a relationship between local sediment cover extent and relative sediment supply, but that this relationship is altered as a function of local bedrock roughness. We consider the implications of our findings for the form of sediment cover relationships.

Experimental investigation on densification behavior and surface roughness of AlSi10Mg powders produced by selective laser melting

NASA Astrophysics Data System (ADS)

Wang, Lin-zhi; Wang, Sen; Wu, Jiao-jiao

2017-11-01

Effects of laser energy density (LED) on densities and surface roughness of AlSi10Mg samples processed by selective laser melting were studied. The densification behaviors of the SLM manufactured AlSi10Mg samples at different LEDs were characterized by a solid densitometer, an industrial X-ray and CT detection system. A field emission scanning electron microscope, an automatic optical measuring system, and a surface profiler were used for measurements of surface roughness. The results show that relatively high density can be obtained with the point distance of 80-105 μm and the exposure time of 140-160 μs. The LED has an important influence on the surface morphology of the forming part, too high LED may lead to balling effect, while too low LED tends to produce defects, such as porosity and microcrack, and then affect surface roughness and porosities of the parts finally.

Incorporation of a high-roughness lower boundary into a mesoscale model for studies of dry deposition over complex terrain

NASA Astrophysics Data System (ADS)

Physick, W. L.; Garratt, J. R.

1995-04-01

For flow over natural surfaces, there exists a roughness sublayer within the atmospheric surface layer near the boundary. In this sublayer (typically 50 z 0 deep in unstable conditions), the Monin-Obukhov (M-O) flux profile relations for homogeneous surfaces cannot be applied. We have incorporated a modified form of the M-O stability functions (Garratt, 1978, 1980, 1983) in a mesoscale model to take account of this roughness sublayer and examined the diurnal variation of the boundary-layer wind and temperature profiles with and without these modifications. We have also investigated the effect of the modified M-O functions on the aerodynamic and laminar-sublayer resistances associated with the transfer of trace gases to vegetation. Our results show that when an observation height or the lowest level in a model is within the roughness sublayer, neglect of the flux-profile modifications leads to an underestimate of resistances by 7% at the most.

Subgap in the Surface Bound States Spectrum of Superfluid (3) 3 He-B with Rough Surface

NASA Astrophysics Data System (ADS)

Nagato, Y.; Higashitani, S.; Nagai, K.

2018-03-01

The subgap structure in the surface bound states spectrum of superfluid ^3He-B with rough surface is discussed. The subgap is formed by the level repulsion between the surface bound state and the continuum states in the course of multiple scattering by the surface roughness. We show that the level repulsion is originated from the nature of the wave function of the surface bound state that is now recognized as Majorana fermion. We study the superfluid ^3He-B with a rough surface and in a magnetic field perpendicular to the surface using the quasi-classical Green function together with a random S-matrix model. We calculate the self-consistent order parameters, the spin polarization density and the surface density of states. It is shown that the subgap is found also in a magnetic field perpendicular to the surface. The magnetic field dependence of the transverse acoustic impedance is also discussed.

Drop impact upon micro- and nanostructured superhydrophobic surfaces.

PubMed

Tsai, Peichun; Pacheco, Sergio; Pirat, Christophe; Lefferts, Leon; Lohse, Detlef

2009-10-20

We experimentally investigate drop impact dynamics onto different superhydrophobic surfaces, consisting of regular polymeric micropatterns and rough carbon nanofibers, with similar static contact angles. The main control parameters are the Weber number We and the roughness of the surface. At small We, i.e., small impact velocity, the impact evolutions are similar for both types of substrates, exhibiting Fakir state, complete bouncing, partial rebouncing, trapping of an air bubble, jetting, and sticky vibrating water balls. At large We, splashing impacts emerge forming several satellite droplets, which are more pronounced for the multiscale rough carbon nanofiber jungles. The results imply that the multiscale surface roughness at nanoscale plays a minor role in the impact events for small We less than or approximately equal 120 but an important one for large We greater than or approximately equal 120. Finally, we find the effect of ambient air pressure to be negligible in the explored parameter regime We less than or approximately equal 150.

EPA scientific integrity policy draft

NASA Astrophysics Data System (ADS)

Showstack, Randy

2011-08-01

The U.S. Environmental Protection Agency (EPA) issued its draft scientific integrity policy on 5 August. The draft policy addresses scientific ethical standards, communications with the public, the use of advisory committees and peer review, and professional development. The draft policy was developed by an ad hoc group of EPA senior staff and scientists in response to a December 2010 memorandum on scientific integrity from the White House Office of Science and Technology Policy. The agency is accepting public comments on the draft through 6 September; comments should be sent to osa.staff@epa.gov. For more information, see http://www.epa.gov/stpc/pdfs/draft-scientific-integrity-policy-aug2011.pdf.

IRIS Toxicological Review of Dichloromethane (Methylene Chloride) (Interagency Science Consultation Draft)

EPA Science Inventory

On March 31, 2010, the draft IRIS Toxicological Review of Dichloromethane (Methylene Chloride) external review draft document and the charge to external peer reviewers were released for public review and comment. The draft document and the charge to external peer reviewers were r...

Drafting--Basic, Drafting--Intermediate: 9255.01.

ERIC Educational Resources Information Center

Dade County Public Schools, Miami, FL.

The course has no prerequisites, offers instruction in basic drafting room techniques and procedures, and also covers job opportunities and industrial methods in engineering. The student is introduced to and asked to perform fundamental drafting problems with working drawings, using multiview and auxiliary views and sections. The course also…

IRIS Toxicological Review of Trimethylbenzenes (Revised External Review Draft)

EPA Science Inventory

In August 2013, EPA submitted a revised draft IRIS assessment of trimethylbenzenes to the agency's Science Advisory Board (SAB) and posted this draft on the IRIS website. EPA had previously released a draft of the assessment for public comment, held a public meeting about the dr...

Mechnical Drawing/Drafting Curriculum Guide.

ERIC Educational Resources Information Center

Gregory, Margaret R.; Benson, Robert T.

This curriculum guide consists of materials for teaching a course in mechanical drawing and drafting. Addressed in the individual units of the guide are the following topics: the nature and scope of drawing and drafting, visualization and spatial relationships, drafting tools and materials, linework, freehand lettering, geometric construction,…

75 FR 51838 - Public Review of Draft Coastal and Marine Ecological Classification Standard

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-23

... DEPARTMENT OF THE INTERIOR Geological Survey Public Review of Draft Coastal and Marine Ecological... comments on draft Coastal and Marine Ecological Classification Standard. SUMMARY: The Federal Geographic Data Committee (FGDC) is conducting a public review of the draft Coastal and Marine Ecological...

10 CFR 51.76 - Draft environmental impact statement-limited work authorization.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 2 2013-01-01 2013-01-01 false Draft environmental impact statement-limited work...-Regulations Implementing Section 102(2) Draft Environmental Impact Statements-Production and Utilization Facilities § 51.76 Draft environmental impact statement—limited work authorization. The NRC will prepare a...

10 CFR 51.77 - Distribution of draft environmental impact statement.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 2 2013-01-01 2013-01-01 false Distribution of draft environmental impact statement. 51...-Regulations Implementing Section 102(2) Draft Environmental Impact Statements-Production and Utilization Facilities § 51.77 Distribution of draft environmental impact statement. (a) In addition to the distribution...

10 CFR 51.77 - Distribution of draft environmental impact statement.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 2 2011-01-01 2011-01-01 false Distribution of draft environmental impact statement. 51...-Regulations Implementing Section 102(2) Draft Environmental Impact Statements-Production and Utilization Facilities § 51.77 Distribution of draft environmental impact statement. (a) In addition to the distribution...

10 CFR 51.76 - Draft environmental impact statement-limited work authorization.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 2 2011-01-01 2011-01-01 false Draft environmental impact statement-limited work...-Regulations Implementing Section 102(2) Draft Environmental Impact Statements-Production and Utilization Facilities § 51.76 Draft environmental impact statement—limited work authorization. The NRC will prepare a...

77 FR 44610 - Notice of Availability of Draft Environmental Assessment

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-30

.... 12968-001-CT] Notice of Availability of Draft Environmental Assessment FirstLight Hydro Generating...). Staff prepared a draft environmental assessment (EA), which analyzes the potential environmental effects... human environment. A copy of the draft EA is available for review at the Commission in the Public...

40 CFR 1502.9 - Draft, final, and supplemental statements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 34 2012-07-01 2012-07-01 false Draft, final, and supplemental... IMPACT STATEMENT § 1502.9 Draft, final, and supplemental statements. Except for proposals for legislation... supplemented. (a) Draft environmental impact statements shall be prepared in accordance with the scope decided...

10 CFR 51.76 - Draft environmental impact statement-limited work authorization.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 2 2014-01-01 2014-01-01 false Draft environmental impact statement-limited work...-Regulations Implementing Section 102(2) Draft Environmental Impact Statements-Production and Utilization Facilities § 51.76 Draft environmental impact statement—limited work authorization. The NRC will prepare a...

40 CFR 1502.9 - Draft, final, and supplemental statements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 33 2011-07-01 2011-07-01 false Draft, final, and supplemental... IMPACT STATEMENT § 1502.9 Draft, final, and supplemental statements. Except for proposals for legislation... supplemented. (a) Draft environmental impact statements shall be prepared in accordance with the scope decided...

10 CFR 51.77 - Distribution of draft environmental impact statement.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 2 2012-01-01 2012-01-01 false Distribution of draft environmental impact statement. 51...-Regulations Implementing Section 102(2) Draft Environmental Impact Statements-Production and Utilization Facilities § 51.77 Distribution of draft environmental impact statement. (a) In addition to the distribution...

29 CFR 1918.82 - Building drafts.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 29 Labor 7 2011-07-01 2011-07-01 false Building drafts. 1918.82 Section 1918.82 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR LONGSHORING Handling Cargo § 1918.82 Building drafts. (a) Drafts shall...

10 CFR 51.76 - Draft environmental impact statement-limited work authorization.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 2 2012-01-01 2012-01-01 false Draft environmental impact statement-limited work...-Regulations Implementing Section 102(2) Draft Environmental Impact Statements-Production and Utilization Facilities § 51.76 Draft environmental impact statement—limited work authorization. The NRC will prepare a...

40 CFR 1502.9 - Draft, final, and supplemental statements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Draft, final, and supplemental... IMPACT STATEMENT § 1502.9 Draft, final, and supplemental statements. Except for proposals for legislation... supplemented. (a) Draft environmental impact statements shall be prepared in accordance with the scope decided...

29 CFR 1918.82 - Building drafts.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 29 Labor 7 2014-07-01 2014-07-01 false Building drafts. 1918.82 Section 1918.82 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR LONGSHORING Handling Cargo § 1918.82 Building drafts. (a) Drafts shall...

29 CFR 1918.82 - Building drafts.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 29 Labor 7 2012-07-01 2012-07-01 false Building drafts. 1918.82 Section 1918.82 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR LONGSHORING Handling Cargo § 1918.82 Building drafts. (a) Drafts shall...

40 CFR 1502.9 - Draft, final, and supplemental statements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 33 2014-07-01 2014-07-01 false Draft, final, and supplemental... IMPACT STATEMENT § 1502.9 Draft, final, and supplemental statements. Except for proposals for legislation... supplemented. (a) Draft environmental impact statements shall be prepared in accordance with the scope decided...

10 CFR 51.77 - Distribution of draft environmental impact statement.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 2 2014-01-01 2014-01-01 false Distribution of draft environmental impact statement. 51...-Regulations Implementing Section 102(2) Draft Environmental Impact Statements-Production and Utilization Facilities § 51.77 Distribution of draft environmental impact statement. (a) In addition to the distribution...

40 CFR 1502.9 - Draft, final, and supplemental statements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 34 2013-07-01 2013-07-01 false Draft, final, and supplemental... IMPACT STATEMENT § 1502.9 Draft, final, and supplemental statements. Except for proposals for legislation... supplemented. (a) Draft environmental impact statements shall be prepared in accordance with the scope decided...

29 CFR 1918.82 - Building drafts.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 29 Labor 7 2013-07-01 2013-07-01 false Building drafts. 1918.82 Section 1918.82 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR LONGSHORING Handling Cargo § 1918.82 Building drafts. (a) Drafts shall...

78 FR 54906 - Draft Supplemental Environmental Impact Report/Environmental Impact Statement for a Proposed...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-06

...-FF08ECAR00] Draft Supplemental Environmental Impact Report/Environmental Impact Statement for a Proposed... Conservation Commission (CVCC), has prepared a joint draft Supplemental Environmental Impact Report/Environmental Impact Statement (draft Supplemental EIR/EIS) under the National Environmental Policy Act (NEPA...

77 FR 69632 - Draft Guidance for Industry on Electronic Source Data in Clinical Investigations; Availability

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-20

...] Draft Guidance for Industry on Electronic Source Data in Clinical Investigations; Availability AGENCY... announcing the availability of a draft guidance for industry entitled ``Electronic Source Data in Clinical... in Clinical Investigations.'' This revised draft document provides guidance to sponsors, contract...

75 FR 22400 - Draft Test Guidelines; Reopening of Comment Period

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-28

... ENVIRONMENTAL PROTECTION AGENCY [EPA-HQ-OPP-2009-0681; FRL-8822-3] Draft Test Guidelines... draft test guidelines for product performance of public health uses of antimicrobial agents. EPA...-8437-2). In that document, EPA announced the availability of four draft test guidelines for product...

IRIS Toxicological Review of Inorganic Arsenic (Cancer) (Interagency Science Consultation Draft)

EPA Science Inventory

On February 19, 2010, the draft IRIS Toxicological Review of Inorganic Arsenic (Cancer) external review draft document and the charge to external peer reviewers were released for public review and comment. The draft document and the charge to external peer reviewers were reviewed...

76 FR 9345 - Soule Hydro, LLC; Notice of Draft License Application and Preliminary Draft Environmental...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-17

...] Soule Hydro, LLC; Notice of Draft License Application and Preliminary Draft Environmental Assessment (PDEA) and Request for Preliminary Terms and Conditions Take notice that the following hydroelectric... Project: With this notice the Commission is soliciting (1) preliminary terms, conditions, and...

76 FR 10908 - Draft Guidance for Industry on Medication Guides-Distribution Requirements and Inclusion of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-28

...] Draft Guidance for Industry on Medication Guides--Distribution Requirements and Inclusion of Medication... a draft guidance for industry entitled ``Medication Guides--Distribution Requirements and Inclusion... Inclusion of Medication Guides in Risk Evaluation and Mitigation Strategies (REMS).'' This draft guidance is...

10 CFR 51.76 - Draft environmental impact statement-limited work authorization.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Draft environmental impact statement-limited work...-Regulations Implementing Section 102(2) Draft Environmental Impact Statements-Production and Utilization Facilities § 51.76 Draft environmental impact statement—limited work authorization. The NRC will prepare a...

10 CFR 51.77 - Distribution of draft environmental impact statement.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Distribution of draft environmental impact statement. 51...-Regulations Implementing Section 102(2) Draft Environmental Impact Statements-Production and Utilization Facilities § 51.77 Distribution of draft environmental impact statement. (a) In addition to the distribution...

Effects of bio-inspired microscale roughness on macroscale flow structures

NASA Astrophysics Data System (ADS)

Bocanegra Evans, Humberto; Hamed, Ali M.; Gorumlu, Serdar; Doosttalab, Ali; Aksak, Burak; Chamorro, Leonardo P.; Castillo, Luciano

2016-11-01

The interaction between rough surfaces and flows is a complex physical situation that produces rich flow phenomena. While random roughness typically increases drag, properly engineered roughness patterns may produce positive results, e.g. dimples in a golf ball. Here we present a set of PIV measurements in an index matched facility of the effect of a bio-inspired surface that consists of an array of mushroom-shaped micro-pillars. The experiments are carried out-under fully wetted conditions-in a flow with adverse pressure gradient, triggering flow separation. The introduction of the micro-pillars dramatically decreases the size of the recirculation bubble; the area with backflow is reduced by approximately 60%. This suggests a positive impact on the form drag generated by the fluid. Furthermore, a negligible effect is seen on the turbulence production terms. The micro-pillars affect the flow by generating low and high pressure perturbations at the interface between the bulk and roughness layer, in a fashion comparable to that of synthetic jets. The passive approach, however, facilitates the implementation of this coating. As the mechanism does not rely on surface hydrophobicity, it is well suited for underwater applications and its functionality should not degrade over time.

Effect of substrate roughness on the corrosion behaviour of the Al2O3/MA 956 system.

PubMed

García-Alonso, M C; Escudero, M L; González-Carrasco, J L; Chao, J

2000-01-01

This paper presents the influence of substrate roughness on the corrosion behaviour of the Al2O3/MA 956 system. An alumina layer of thickness 1-5 microm was generated of the MA956 alloy by thermal oxidation at 1100 degrees C using different exposure times. This Al2O3/MA 956 system with a polished substrate has shown excellent corrosion behaviour in a physiological fluid, due to the fact that the alpha-Al2O3 layer formed is dense, continuous and firmly adhered to the substrate, irrespective of the scale thickness. This good adherence allows it to withstand potentials above 1.7 V. Specimens with rough finish substrate and treatment times above 10 h present spallation of the alumina layer at the crests of the roughness profile. In this case a mixed corrosion behaviour between an alumina coated material and one with a passive layer is observed. In both types of specimens, rough and smooth, once the passivation layer is broken the repassivation capacity of the substrate is ensured due to the high chromium content of the alloy, under oxygenation conditions.

Growth of rough-surface p-GaN layers on InGaN/GaN multiple-quantum-well structures by metalorganic chemical vapor deposition and their application to GaN-based solar cells

NASA Astrophysics Data System (ADS)

Mori, Takuma; Egawa, Takashi; Miyoshi, Makoto

2017-08-01

We conducted the study on the growth of rough-surface p-GaN layers on InGaN/GaN multiple-quantum-well (MQW) structures by metalorganic chemical vapor deposition (MOCVD). It was found that the sum of InGaN well thickness t well_total was a predominant factor to form the rough surface, in addition to the growth temperature as low as 800 °C for the p-GaN layers. Microstructure analyses revealed that the rough surfaces consisted of a certain number of hexagonal V-shaped pits starting from dislocations propagated through an under layer and they increased with the increased t well_total. It was confirmed that the light absorption was enlarged for MQW structure samples with rough-surface p-GaN layers on the top, owing to not only the thickness effect in MQWs but also their reduced light reflection on the surfaces. It was also confirmed that these optical properties contributed to the performance improvement in InGaN/GaN MQW solar cells.

High-quality permanent draft genome sequence of the Lebeckia - nodulating Burkholderia dilworthii strain WSM3556T

DOE Office of Scientific and Technical Information (OSTI.GOV)

De Meyer, Sofie E.; Tian, Rui; Seshadri, Rekha

Burkholderia dilworthii strain WSM3556T is an aerobic, motile, Gram-negative, non-spore-forming rod that was isolated from an effective N2-fixing root nodule of Lebeckia ambigua collected near Grotto Bay Nature Reserve, in the Western Cape of South Africa, in October 2004. This plant persists in infertile and deep sandy soils with acidic pH, and is therefore an ideal candidate for a perennial based agriculture system in Western Australia. WSM3556T thus represents a potential inoculant quality strain for L. ambigua for which we describe the general features, together with genome sequence and annotation. Lastly, the 7,679,067 bp high-quality permanent draft genome is arrangedmore » in 140 scaffolds of 141 contigs, contains 7,059 protein-coding genes and 64 RNA-only encoding genes, and is part of the GEBA-RNB project proposal.« less

High-quality permanent draft genome sequence of the Lebeckia ambigua-nodulating Burkholderia sp. strain WSM4176

DOE Office of Scientific and Technical Information (OSTI.GOV)

De Meyer, Sofie E.; Tian, Rui; Seshadri, Rekha

We report that Burkholderia sp. strain WSM4176 is an aerobic, motile, Gram-negative, non-spore-forming rod that was isolated from an effective N2-fixing root nodule of Lebeckia ambigua collected in Nieuwoudtville, Western Cape of South Africa, in October 2007. This plant persists in infertile, acidic and deep sandy soils, and is therefore an ideal candidate for a perennial based agriculture system in Western Australia. Here we describe the features of Burkholderia sp. strain WSM4176, which represents a potential inoculant quality strain for L. ambigua, together with sequence and annotation. The 9,065,247 bp high-quality-draft genome is arranged in 13 scaffolds of 65 contigs,more » contains 8369 protein-coding genes and 128 RNA-only encoding genes, and is part of the GEBA-RNB project proposal (Project ID 882).« less

The draft genome of Ciona intestinalis: insights into chordate and vertebrate origins.

PubMed

Dehal, Paramvir; Satou, Yutaka; Campbell, Robert K; Chapman, Jarrod; Degnan, Bernard; De Tomaso, Anthony; Davidson, Brad; Di Gregorio, Anna; Gelpke, Maarten; Goodstein, David M; Harafuji, Naoe; Hastings, Kenneth E M; Ho, Isaac; Hotta, Kohji; Huang, Wayne; Kawashima, Takeshi; Lemaire, Patrick; Martinez, Diego; Meinertzhagen, Ian A; Necula, Simona; Nonaka, Masaru; Putnam, Nik; Rash, Sam; Saiga, Hidetoshi; Satake, Masanobu; Terry, Astrid; Yamada, Lixy; Wang, Hong-Gang; Awazu, Satoko; Azumi, Kaoru; Boore, Jeffrey; Branno, Margherita; Chin-Bow, Stephen; DeSantis, Rosaria; Doyle, Sharon; Francino, Pilar; Keys, David N; Haga, Shinobu; Hayashi, Hiroko; Hino, Kyosuke; Imai, Kaoru S; Inaba, Kazuo; Kano, Shungo; Kobayashi, Kenji; Kobayashi, Mari; Lee, Byung-In; Makabe, Kazuhiro W; Manohar, Chitra; Matassi, Giorgio; Medina, Monica; Mochizuki, Yasuaki; Mount, Steve; Morishita, Tomomi; Miura, Sachiko; Nakayama, Akie; Nishizaka, Satoko; Nomoto, Hisayo; Ohta, Fumiko; Oishi, Kazuko; Rigoutsos, Isidore; Sano, Masako; Sasaki, Akane; Sasakura, Yasunori; Shoguchi, Eiichi; Shin-i, Tadasu; Spagnuolo, Antoinetta; Stainier, Didier; Suzuki, Miho M; Tassy, Olivier; Takatori, Naohito; Tokuoka, Miki; Yagi, Kasumi; Yoshizaki, Fumiko; Wada, Shuichi; Zhang, Cindy; Hyatt, P Douglas; Larimer, Frank; Detter, Chris; Doggett, Norman; Glavina, Tijana; Hawkins, Trevor; Richardson, Paul; Lucas, Susan; Kohara, Yuji; Levine, Michael; Satoh, Nori; Rokhsar, Daniel S

2002-12-13

The first chordates appear in the fossil record at the time of the Cambrian explosion, nearly 550 million years ago. The modern ascidian tadpole represents a plausible approximation to these ancestral chordates. To illuminate the origins of chordate and vertebrates, we generated a draft of the protein-coding portion of the genome of the most studied ascidian, Ciona intestinalis. The Ciona genome contains approximately 16,000 protein-coding genes, similar to the number in other invertebrates, but only half that found in vertebrates. Vertebrate gene families are typically found in simplified form in Ciona, suggesting that ascidians contain the basic ancestral complement of genes involved in cell signaling and development. The ascidian genome has also acquired a number of lineage-specific innovations, including a group of genes engaged in cellulose metabolism that are related to those in bacteria and fungi.

High-quality permanent draft genome sequence of the Lebeckia - nodulating Burkholderia dilworthii strain WSM3556T

DOE PAGES

De Meyer, Sofie E.; Tian, Rui; Seshadri, Rekha; ...

2015-09-19

Burkholderia dilworthii strain WSM3556T is an aerobic, motile, Gram-negative, non-spore-forming rod that was isolated from an effective N2-fixing root nodule of Lebeckia ambigua collected near Grotto Bay Nature Reserve, in the Western Cape of South Africa, in October 2004. This plant persists in infertile and deep sandy soils with acidic pH, and is therefore an ideal candidate for a perennial based agriculture system in Western Australia. WSM3556T thus represents a potential inoculant quality strain for L. ambigua for which we describe the general features, together with genome sequence and annotation. Lastly, the 7,679,067 bp high-quality permanent draft genome is arrangedmore » in 140 scaffolds of 141 contigs, contains 7,059 protein-coding genes and 64 RNA-only encoding genes, and is part of the GEBA-RNB project proposal.« less

High-quality permanent draft genome sequence of the Lebeckia ambigua-nodulating Burkholderia sp. strain WSM4176

DOE PAGES

De Meyer, Sofie E.; Tian, Rui; Seshadri, Rekha; ...

2015-10-16

We report that Burkholderia sp. strain WSM4176 is an aerobic, motile, Gram-negative, non-spore-forming rod that was isolated from an effective N2-fixing root nodule of Lebeckia ambigua collected in Nieuwoudtville, Western Cape of South Africa, in October 2007. This plant persists in infertile, acidic and deep sandy soils, and is therefore an ideal candidate for a perennial based agriculture system in Western Australia. Here we describe the features of Burkholderia sp. strain WSM4176, which represents a potential inoculant quality strain for L. ambigua, together with sequence and annotation. The 9,065,247 bp high-quality-draft genome is arranged in 13 scaffolds of 65 contigs,more » contains 8369 protein-coding genes and 128 RNA-only encoding genes, and is part of the GEBA-RNB project proposal (Project ID 882).« less

Minimum Information about a Cardiac Electrophysiology Experiment (MICEE): Standardised Reporting for Model Reproducibility, Interoperability, and Data Sharing

PubMed Central

Quinn, TA; Granite, S; Allessie, MA; Antzelevitch, C; Bollensdorff, C; Bub, G; Burton, RAB; Cerbai, E; Chen, PS; Delmar, M; DiFrancesco, D; Earm, YE; Efimov, IR; Egger, M; Entcheva, E; Fink, M; Fischmeister, R; Franz, MR; Garny, A; Giles, WR; Hannes, T; Harding, SE; Hunter, PJ; Iribe, G; Jalife, J; Johnson, CR; Kass, RS; Kodama, I; Koren, G; Lord, P; Markhasin, VS; Matsuoka, S; McCulloch, AD; Mirams, GR; Morley, GE; Nattel, S; Noble, D; Olesen, SP; Panfilov, AV; Trayanova, NA; Ravens, U; Richard, S; Rosenbaum, DS; Rudy, Y; Sachs, F; Sachse, FB; Saint, DA; Schotten, U; Solovyova, O; Taggart, P; Tung, L; Varró, A; Volders, PG; Wang, K; Weiss, JN; Wettwer, E; White, E; Wilders, R; Winslow, RL; Kohl, P

2011-01-01

Cardiac experimental electrophysiology is in need of a well-defined Minimum Information Standard for recording, annotating, and reporting experimental data. As a step toward establishing this, we present a draft standard, called Minimum Information about a Cardiac Electrophysiology Experiment (MICEE). The ultimate goal is to develop a useful tool for cardiac electrophysiologists which facilitates and improves dissemination of the minimum information necessary for reproduction of cardiac electrophysiology research, allowing for easier comparison and utilisation of findings by others. It is hoped that this will enhance the integration of individual results into experimental, computational, and conceptual models. In its present form, this draft is intended for assessment and development by the research community. We invite the reader to join this effort, and, if deemed productive, implement the Minimum Information about a Cardiac Electrophysiology Experiment standard in their own work. PMID:21745496

High-quality permanent draft genome sequence of Rhizobium leguminosarum bv. viciae strain GB30; an effective microsymbiont of Pisum sativum growing in Poland

DOE PAGES

Mazur, Andrzej; De Meyer, Sofie E.; Tian, Rui; ...

2015-07-16

We report that Rhizobium leguminosarum bv. viciae GB30 is an aerobic, motile, Gram-negative, non-spore-forming rod that can exist as a soil saprophyte or as a legume microsymbiont of Pisum sativum. GB30 was isolated in Poland from a nodule recovered from the roots of Pisum sativum growing at Janow. GB30 is also an effective microsymbiont of the annual forage legumes vetch and pea. Here we describe the features of R. leguminosarum bv. viciae strain GB30, together with sequence and annotation. The 7,468,464 bp high-quality permanent draft genome is arranged in 78 scaffolds of 78 contigs containing 7,227 protein-coding genes and 75more » RNA-only encoding genes, and is part of the GEBA-RNB project proposal.« less

High-Quality draft genome sequence of the Lotus spp. microsymbiont Mesorhizobium loti strain CJ3Sym

DOE PAGES

Reeve, Wayne; Sullivan, John; Ronson, Clive; ...

2015-08-14

Mesorhizobium loti strain CJ3Sym was isolated in 1998 following transfer of the integrative and conjugative element ICE Ml Sym R7A , also known as the R7A symbiosis island, in a laboratory mating from the donor M. loti strain R7A to a nonsymbiotic recipient Mesorhizobium strain CJ3. Strain CJ3 was originally isolated from a field site in the Rocklands range in New Zealand in 1994. CJ3Sym is an aerobic, Gram-negative, non-spore-forming rod. This report reveals the genome of M. loti strain CJ3Sym currently comprises 70 scaffolds totaling 7,563,725 bp. In conclusion, the high-quality draft genome is arranged in 70 scaffolds ofmore » 71 contigs, contains 7,331 protein-coding genes and 70 RNA-only encoding genes, and is part of the GEBA-RNB project proposal.« less

Technology of Producing the Contact Connections of Superconductor Metal-Sheathed Cable

NASA Astrophysics Data System (ADS)

Jakubowski, Andrzej

2017-06-01

The technology of producing the current contact connections on the superconductor cable edges is presented. This lead cable is used as one of the major elements of the magnetic system in thermonuclear reactor construction, actuality for modern world energy. The technology is realized by the radial draft of metal thin-walled tube on the conductor's package. The filling of various profiles by round section wire is optimized. Geometrical characteristics of the dangerous crosssection (as a broken ring) of thin-walled tube injured by the sector cut-out are accounted. The comparative strength calculation of the solid and injured tubes at a longitudinal compression and lateral bending is acted. The radial draft mechanism of cylindrical thin-walled sheath with the wire packing is designed. The necessity to use the nonlinear theory for the sheaths calculate is set. The resilient co-operation of wires as the parallel located cylinders with the contact stripes of rectangular form is considered.

High-Quality draft genome sequence of the Lotus spp. microsymbiont Mesorhizobium loti strain CJ3Sym

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reeve, Wayne; Sullivan, John; Ronson, Clive

Mesorhizobium loti strain CJ3Sym was isolated in 1998 following transfer of the integrative and conjugative element ICE Ml Sym R7A , also known as the R7A symbiosis island, in a laboratory mating from the donor M. loti strain R7A to a nonsymbiotic recipient Mesorhizobium strain CJ3. Strain CJ3 was originally isolated from a field site in the Rocklands range in New Zealand in 1994. CJ3Sym is an aerobic, Gram-negative, non-spore-forming rod. This report reveals the genome of M. loti strain CJ3Sym currently comprises 70 scaffolds totaling 7,563,725 bp. In conclusion, the high-quality draft genome is arranged in 70 scaffolds ofmore » 71 contigs, contains 7,331 protein-coding genes and 70 RNA-only encoding genes, and is part of the GEBA-RNB project proposal.« less

Spiral optical designs for nonimaging applications

NASA Astrophysics Data System (ADS)

Zamora, Pablo; Benítez, Pablo; Miñano, Juan C.; Vilaplana, Juan; Buljan, Marina

2011-10-01

Manufacturing technologies as injection molding or embossing specify their production limits for minimum radii of the vertices or draft angle for demolding, for instance. In some demanding nonimaging applications, these restrictions may limit the system optical efficiency or affect the generation of undesired artifacts on the illumination pattern. A novel manufacturing concept is presented here, in which the optical surfaces are not obtained from the usual revolution symmetry with respect to a central axis (z axis), but they are calculated as free-form surfaces describing a spiral trajectory around z axis. The main advantage of this new concept lies in the manufacturing process: a molded piece can be easily separated from its mold just by applying a combination of rotational movement around axis z and linear movement along axis z, even for negative draft angles. Some of these spiral symmetry examples will be shown here, as well as their simulated results.

Spiral nonimaging optical designs

NASA Astrophysics Data System (ADS)

Zamora, Pablo; Benítez, Pablo; Miñano, Juan C.; Vilaplana, Juan

2011-10-01

Manufacturing technologies as injection molding or embossing specify their production limits for minimum radii of the vertices or draft angle for demolding, for instance. In some demanding nonimaging applications, these restrictions may limit the system optical efficiency or affect the generation of undesired artifacts on the illumination pattern. A novel manufacturing concept is presented here, in which the optical surfaces are not obtained from the usual revolution symmetry with respect to a central axis (z axis), but they are calculated as free-form surfaces describing a spiral trajectory around z axis. The main advantage of this new concept lies in the manufacturing process: a molded piece can be easily separated from its mold just by applying a combination of rotational movement around axis z and linear movement along axis z, even for negative draft angles. Some of these spiral symmetry examples will be shown here, as well as their simulated results.

Novel freeform optical surface design with spiral symmetry

NASA Astrophysics Data System (ADS)

Zamora, Pablo; Benítez, Pablo; Miñano, Juan C.; Vilaplana, Juan

2011-10-01

Manufacturing technologies as injection molding or embossing specify their production limits for minimum radii of the vertices or draft angle for demolding, for instance. These restrictions may limit the system optical efficiency or affect the generation of undesired artifacts on the illumination pattern when dealing with optical design. A novel manufacturing concept is presented here, in which the optical surfaces are not obtained from the usual revolution symmetry with respect to a central axis (z axis), but they are calculated as free-form surfaces describing a spiral trajectory around z axis. The main advantage of this new concept lies in the manufacturing process: a molded piece can be easily separated from its mold just by applying a combination of rotational movement around axis z and linear movement along axis z, even for negative draft angles. The general designing procedure will be described in detail.

Global Insurgency Strategy and the Salafi Jihad Movement

DTIC Science & Technology

2008-04-01

Coll and Glasser,  is through public e­mail services such as  Hotmail . Here is how it  works: An operative opens an account on Hotmail , “writes a...secretly, reported by Coll and Glasser,  is through public e­mail services such as  Hotmail . Here is how it  works: An operative opens an account on... Hotmail , “writes a message  in draft form, saves it as a draft, and then transmits the e­mail account  name and password during chatter on a relatively

Draft Genome Sequence of Bacillus cereus CITVM-11.1, a Strain Exhibiting Interesting Antifungal Activities.

PubMed

Caballero, Javier; Peralta, Cecilia; Molla, Antonella; Del Valle, Eleodoro E; Caballero, Primitivo; Berry, Colin; Felipe, Verónica; Yaryura, Pablo; Palma, Leopoldo

2018-01-01

Bacillus cereus is a gram-positive, spore-forming bacterium possessing an important and historical record as a human-pathogenic bacterium. However, several strains of this species exhibit interesting potential to be used as plant growth-promoting rhizobacteria. Here, we report the draft genome sequence of B. cereus strain CITVM-11.1, which consists of 37 contig sequences, accounting for 5,746,486 bp (with a GC content of 34.8%) and 5,752 predicted protein-coding sequences. Several of them could potentially be involved in plant-bacterium interactions and may contribute to the strong antagonistic activity shown by this strain against the charcoal root rot fungus, Macrophomina phaseolina. This genomic sequence also showed a number of genes that may confer this strain resistance against several polluting heavy metals and for the bioconversion of mycotoxins. © 2018 S. Karger AG, Basel.

Mercury study report to Congress. Volume 4. Health effects of mercury and mercury compounds. Sab review draft

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schoeny, R.

1996-06-01

This volume of the draft Mercury Study Report to Congress summarizes the available information on human health effects and animal data for hazard identification and dose-response assessment for three forms of mercury: elemental mercury, mercury chloride (inorganic mercury), and methylmercury (organic mercury). Effects are summarized by endpoint. The risk assessment evaluates carcinogenicity, mutagenicity, developmental toxicity and general systemic toxicity of these chemical species of mercury. Toxicokinetics (absorption, distribution, metabolism and excretion) are described for each of the three mercury species. PBPK models are described, but not applied in risk assessment. Reference doses are calculated for inorganic and methylmercury; a referencemore » concentration for inhaled elemental mercury is provided. A quantitiative analysis of factors contributing to variability and uncertainty in the methylmercury RfD is provided in an appendix. Interations and sensitive populations are described.« less

High-quality permanent draft genome sequence of Rhizobium leguminosarum bv. viciae strain GB30; an effective microsymbiont of Pisum sativum growing in Poland

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mazur, Andrzej; De Meyer, Sofie E.; Tian, Rui

We report that Rhizobium leguminosarum bv. viciae GB30 is an aerobic, motile, Gram-negative, non-spore-forming rod that can exist as a soil saprophyte or as a legume microsymbiont of Pisum sativum. GB30 was isolated in Poland from a nodule recovered from the roots of Pisum sativum growing at Janow. GB30 is also an effective microsymbiont of the annual forage legumes vetch and pea. Here we describe the features of R. leguminosarum bv. viciae strain GB30, together with sequence and annotation. The 7,468,464 bp high-quality permanent draft genome is arranged in 78 scaffolds of 78 contigs containing 7,227 protein-coding genes and 75more » RNA-only encoding genes, and is part of the GEBA-RNB project proposal.« less

Genome sequence of the dark pink pigmented Listia bainesii microsymbiont Methylobacterium sp. WSM2598

PubMed Central

2014-01-01

Strains of a pink-pigmented Methylobacterium sp. are effective nitrogen- (N2) fixing microsymbionts of species of the African crotalarioid genus Listia. Strain WSM2598 is an aerobic, motile, Gram-negative, non-spore-forming rod isolated in 2002 from a Listia bainesii root nodule collected at Estcourt Research Station in South Africa. Here we describe the features of Methylobacterium sp. WSM2598, together with information and annotation of a high-quality draft genome sequence. The 7,669,765 bp draft genome is arranged in 5 scaffolds of 83 contigs, contains 7,236 protein-coding genes and 18 RNA-only encoding genes. This rhizobial genome is one of 100 sequenced as part of the DOE Joint Genome Institute 2010 G enomic E ncyclopedia for B acteria and A rchaea- R oot N odule B acteria (GEBA-RNB) project. PMID:25780498