Spot and Runway Departure Advisor (SARDA)

NASA Technical Reports Server (NTRS)

Jung, Yoon

2016-01-01

Spot and Runway Departure Advisor (SARDA) is a decision support tool to assist airline ramp controllers and ATC tower controllers to manage traffic on the airport surface to significantly improve efficiency and predictability in surface operations. The core function of the tool is the runway scheduler which generates an optimal solution for runway sequence and schedule of departure aircraft, which would minimize system delay and maximize runway throughput. The presentation also discusses the latest status of NASA's current surface research through a collaboration with an airline partner, where a tool is developed for airline ramp operators to assist departure pushback operations. The presentation describes the concept of the SARDA tool and results from human-in-the-loop simulations conducted in 2012 for Dallas-Ft. Worth International Airport and 2014 for Charlotte airport ramp tower.

Humanitarian Relief Capabilities in the Horn of Africa.

DTIC Science & Technology

2014-06-13

surface runways (Central Intelligence Agency 2014a). Camp Lemonnier, the only U.S. military base in Africa, is located in Djibouti. The camp is in close... Intelligence Agency 2014d). Somalia has sixty-one airports, of which six have permanent surface runways (Central 10 Intelligence Agency 2014e). Ethiopia...has fifty-seven airports, of which seventeen have permanent surface runways (Central Intelligence Agency 2014c). The country with the same number

Status of runway slipperiness research

NASA Technical Reports Server (NTRS)

Horne, W. B.

1976-01-01

Runway slipperiness research performed in the United States and Europe since 1968 is reviewed. Topics discussed include: (1) runway flooding during rainstorms; (2) hydroplaning; (3) identification of slippery runways including the results from ground vehicle friction measurements and attempts to correlate these measurements with aircraft stopping performance; (4) progress and problems associated with the development of antihydroplaning runway surface treatments such as pavement grooving and porous friction course (PFC); and (5) runway rubber deposits and their removal.

An overview of the joint FAA/NASA aircraft/ground runway friction program

NASA Technical Reports Server (NTRS)

Yager, Thomas J.

1989-01-01

There is a need for information on runways which may become slippery due to various forms and types of contaminants. Experience has shown that since the beginning of all weather aircraft operations, there have been landing and aborted takeoff incidents and/or accidents each year where aircraft have either run off the end or veered off the shoulder of low friction runways. NASA Langley's Landing and Impact Dynamics Branch is involved in several research programs directed towards obtaining a better understanding of how different tire properties interact with varying pavement surface characteristics to produce acceptable performance for aircraft ground handling requirements. One such effort, which was jointly supported by not only NASA and the FAA but by several aviation industry groups including the Flight Safety Foundation, is described.

14 CFR 25.1533 - Additional operating limitations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... and wet), and runway gradients) for smooth, hard-surfaced runways. Additionally, at the option of the... for variable factors (such as altitude, temperature, wind, and runway gradients) are those at which...

Behavior of aircraft antiskid braking systems on dry and wet runway surfaces - A velocity-rate-controlled, pressure-bias-modulated system

NASA Technical Reports Server (NTRS)

Stubbs, S. M.; Tanner, J. A.

1976-01-01

During maximum braking the average ratio of drag-force friction coefficient developed by the antiskid system to maximum drag-force friction coefficient available at the tire/runway interface was higher on dry surfaces than on wet surfaces. The gross stopping power generated by the brake system on the dry surface was more than twice that obtained on the wet surfaces. With maximum braking applied, the average ratio of side-force friction coefficient developed by the tire under antiskid control to maximum side-force friction available at the tire/runway interface of a free-rolling yawed tire was shown to decrease with increasing yaw angle. Braking reduced the side-force friction coefficient on a dry surface by 75 percent as the wheel slip ratio was increased to 0.3; on a flooded surface the coefficient dropped to near zero for the same slip ratio. Locked wheel skids were observed when the tire encountered a runway surface transition from dry to flooded, due in part to the response time required for the system to sense abrupt changes in the runway friction; however, the antiskid system quickly responded by reducing brake pressure and cycling normally during the remainder of the run on the flooded surface.

Optimization of Airport Surface Traffic: A Case-Study of Incheon International Airport

NASA Technical Reports Server (NTRS)

Eun, Yeonju; Jeon, Daekeun; Lee, Hanbong; Jung, Yoon C.; Zhu, Zhifan; Jeong, Myeongsook; Kim, Hyounkong; Oh, Eunmi; Hong, Sungkwon

2017-01-01

This study aims to develop a controllers decision support tool for departure and surface management of ICN. Airport surface traffic optimization for Incheon International Airport (ICN) in South Korea was studied based on the operational characteristics of ICN and airspace of Korea. For surface traffic optimization, a multiple runway scheduling problem and a taxi scheduling problem were formulated into two Mixed Integer Linear Programming (MILP) optimization models. The Miles-In-Trail (MIT) separation constraint at the departure fix shared by the departure flights from multiple runways and the runway crossing constraints due to the taxi route configuration specific to ICN were incorporated into the runway scheduling and taxiway scheduling problems, respectively. Since the MILP-based optimization model for the multiple runway scheduling problem may be computationally intensive, computation times and delay costs of different solving methods were compared for a practical implementation. This research was a collaboration between Korea Aerospace Research Institute (KARI) and National Aeronautics and Space Administration (NASA).

Optimization of Airport Surface Traffic: A Case-Study of Incheon International Airport

NASA Technical Reports Server (NTRS)

Eun, Yeonju; Jeon, Daekeun; Lee, Hanbong; Jung, Yoon Chul; Zhu, Zhifan; Jeong, Myeong-Sook; Kim, Hyoun Kyoung; Oh, Eunmi; Hong, Sungkwon

2017-01-01

This study aims to develop a controllers' decision support tool for departure and surface management of ICN. Airport surface traffic optimization for Incheon International Airport (ICN) in South Korea was studied based on the operational characteristics of ICN and airspace of Korea. For surface traffic optimization, a multiple runway scheduling problem and a taxi scheduling problem were formulated into two Mixed Integer Linear Programming (MILP) optimization models. The Miles-In-Trail (MIT) separation constraint at the departure fix shared by the departure flights from multiple runways and the runway crossing constraints due to the taxi route configuration specific to ICN were incorporated into the runway scheduling and taxiway scheduling problems, respectively. Since the MILP-based optimization model for the multiple runway scheduling problem may be computationally intensive, computation times and delay costs of different solving methods were compared for a practical implementation. This research was a collaboration between Korea Aerospace Research Institute (KARI) and National Aeronautics and Space Administration (NASA).

A Runway Surface Monitor using Internet of Things

NASA Astrophysics Data System (ADS)

Troiano, Amedeo; Pasero, Eros

2014-05-01

The monitoring of runway surfaces, for the detection of ice formation or presence of water, is an important issue for reducing maintenance costs and improving traffic safety. An innovative sensor was developed to detect the presence of ice or water on its surface, and its repeatability, stability and reliability were assessed in different simulations and experiments, performed both in laboratory and in the field. Three sensors were embedded in the runway of the Turin-Caselle airport, in the north-west of Italy, to check the state of its surface. Each sensor was connected to a GPRS modem to send the collected data to a common database. The entire system was installed about three years ago, and up to now it shows correct work and automatic reactivation after malfunctions without any external help. The state of the runway surface is virtual represented in an internet website, using the Internet of Things features and opening new scenarios.

System Oriented Runway Management: A Research Update

NASA Technical Reports Server (NTRS)

Lohr, Gary W.; Brown, Sherilyn A.; Stough, Harry P., III; Eisenhawer, Steve; Atkins, Stephen; Long, Dou

2011-01-01

The runway configuration used by an airport has significant implications with respect to its capacity and ability to effectively manage surface and airborne traffic. Aircraft operators rely on runway configuration information because it can significantly affect an airline's operations and planning of their resources. Current practices in runway management are limited by a relatively short time horizon for reliable weather information and little assistance from automation. Wind velocity is the primary consideration when selecting a runway configuration; however when winds are below a defined threshold, discretion may be used to determine the configuration. Other considerations relevant to runway configuration selection include airport operator constraints, weather conditions (other than winds) traffic demand, user preferences, surface congestion, and navigational system outages. The future offers an increasingly complex landscape for the runway management process. Concepts and technologies that hold the potential for capacity and efficiency increases for both operations on the airport surface and in terminal and enroute airspace are currently under investigation. Complementary advances in runway management are required if capacity and efficiency increases in those areas are to be realized. The System Oriented Runway Management (SORM) concept has been developed to address this critical part of the traffic flow process. The SORM concept was developed to address all aspects of runway management for airports of varying sizes and to accommodate a myriad of traffic mixes. SORM, to date, addresses the single airport environment; however, the longer term vision is to incorporate capabilities for multiple airport (Metroplex) operations as well as to accommodate advances in capabilities resulting from ongoing research. This paper provides an update of research supporting the SORM concept including the following: a concept of overview, results of a TRCM simulation, single airport and Metroplex modeling effort and a benefits assessment.

14 CFR 25.105 - Takeoff.

Code of Federal Regulations, 2014 CFR

2014-01-01

..., hard-surfaced runways; and (ii) At the option of the applicant, grooved or porous friction course wet, hard-surfaced runways. (2) Smooth water, in the case of seaplanes and amphibians; and (3) Smooth, dry...

14 CFR 25.105 - Takeoff.

Code of Federal Regulations, 2011 CFR

2011-01-01

..., hard-surfaced runways; and (ii) At the option of the applicant, grooved or porous friction course wet, hard-surfaced runways. (2) Smooth water, in the case of seaplanes and amphibians; and (3) Smooth, dry...

14 CFR 25.105 - Takeoff.

Code of Federal Regulations, 2012 CFR

2012-01-01

..., hard-surfaced runways; and (ii) At the option of the applicant, grooved or porous friction course wet, hard-surfaced runways. (2) Smooth water, in the case of seaplanes and amphibians; and (3) Smooth, dry...

14 CFR 25.105 - Takeoff.

Code of Federal Regulations, 2013 CFR

2013-01-01

..., hard-surfaced runways; and (ii) At the option of the applicant, grooved or porous friction course wet, hard-surfaced runways. (2) Smooth water, in the case of seaplanes and amphibians; and (3) Smooth, dry...

Friction evaluation of unpaved, gypsum-surface runways at Northrup Strip, White Sands Missile Range, in support of Space Shuttle Orbiter landing and retrieval operations

NASA Technical Reports Server (NTRS)

Yager, T. J.; Horne, W. B.

1980-01-01

Friction measurement results obtained on the gypsum surface runways at Northrup Strip, White Sands Missile Range, N. M., using an instrumented tire test vehicle and a diagonal braked vehicle, are presented. These runways were prepared to serve as backup landing and retrieval sites to the primary sites located at Dryden Flight Research Center for shuttle orbiter during initial test flights. Similar friction data obtained on paved and other unpaved surfaces was shown for comparison and to indicate that the friction capability measured on the dry gypsum surface runways is sufficient for operations with the shuttle orbiter and the Boeing 747 aircraft. Based on these ground vehicle friction measurements, estimates of shuttle orbiter and aircraft tire friction performance are presented and discussed. General observations concerning the gypsum surface characteristics are also included and several recommendations are made for improving and maintaining adequate surface friction capabilities prior to the first shuttle orbiter landing.

Runway Operations Planning: A Two-Stage Solution Methodology

NASA Technical Reports Server (NTRS)

Anagnostakis, Ioannis; Clarke, John-Paul

2003-01-01

The airport runway is a scarce resource that must be shared by different runway operations (arrivals, departures and runway crossings). Given the possible sequences of runway events, careful Runway Operations Planning (ROP) is required if runway utilization is to be maximized. Thus, Runway Operations Planning (ROP) is a critical component of airport operations planning in general and surface operations planning in particular. From the perspective of departures, ROP solutions are aircraft departure schedules developed by optimally allocating runway time for departures given the time required for arrivals and crossings. In addition to the obvious objective of maximizing throughput, other objectives, such as guaranteeing fairness and minimizing environmental impact, may be incorporated into the ROP solution subject to constraints introduced by Air Traffic Control (ATC) procedures. Generating optimal runway operations plans was approached in with a 'one-stage' optimization routine that considered all the desired objectives and constraints, and the characteristics of each aircraft (weight class, destination, Air Traffic Control (ATC) constraints) at the same time. Since, however, at any given point in time, there is less uncertainty in the predicted demand for departure resources in terms of weight class than in terms of specific aircraft, the ROP problem can be parsed into two stages. In the context of the Departure Planner (OP) research project, this paper introduces Runway Operations Planning (ROP) as part of the wider Surface Operations Optimization (SOO) and describes a proposed 'two stage' heuristic algorithm for solving the Runway Operations Planning (ROP) problem. Focus is specifically given on including runway crossings in the planning process of runway operations. In the first stage, sequences of departure class slots and runwy crossings slots are generated and ranked based on departure runway throughput under stochastic conditions. In the second stage, the departure class slots are populated with specific flights from the pool of available aircraft, by solving an integer program. Preliminary results from the algorithm implementation on real-world traffic data are included.

A Preliminary Evaluation of the Potential Utility of the Surface Condition Analyzer (SCAN) System for Monitoring Runway Water Depth as Relating to Runway Traction.

DTIC Science & Technology

1980-01-01

one year with the savings realized in reduced wear on arresting gear. 2.2 Evaluation of the Potential Utility of the SCAN System for Monitoring Runway...without loss of accuracy due to build-up of rubber and other contaminants on the sensor surface? 2. Can water depth be measured representatively on a...Hargett, E.R., 1974: Skid- Resistance Evaluation of Seven Antihydroplaning Surfaces, Air Force Weapons Laboratory, Kirtland AP. NM4 87117, 39 pp

Runway Incursion Prevention for General Aviation Operations

NASA Technical Reports Server (NTRS)

Jones, Denise R.; Prinzel, Lawrence J., III

2006-01-01

A Runway Incursion Prevention System (RIPS) and additional incursion detection algorithm were adapted for general aviation operations and evaluated in a simulation study at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) in the fall of 2005. RIPS has been designed to enhance surface situation awareness and provide cockpit alerts of potential runway conflicts in order to prevent runway incidents while also improving operational capability. The purpose of the study was to evaluate the airborne incursion detection algorithms and associated alerting and airport surface display concepts for general aviation operations. This paper gives an overview of the system, simulation study, and test results.

Runway Incursion Prevention System for General Aviation Operations

NASA Technical Reports Server (NTRS)

Jones, Denise R.; Prinzel III, Lawrence J.

2006-01-01

A Runway Incursion Prevention System (RIPS) and additional incursion detection algorithm were adapted for general aviation operations and evaluated in a simulation study at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) in the fall of 2005. RIPS has been designed to enhance surface situation awareness and provide cockpit alerts of potential runway conflicts in order to prevent runway incidents while also improving operational capability. The purpose of the study was to evaluate the airborne incursion detection algorithms and associated alerting and airport surface display concepts for general aviation operations. This paper gives an overview of the system, simulation study, and test results.

Considerations on the relationship between white and red centerline runway lights and RVR (Runway Visual Range).

DOT National Transportation Integrated Search

1972-01-01

The runway visual range (RVR) for a Type L-850 bidirectional centerline runway light has been calculated for the red and white output ports at three different current settings for both day and night illuminance thresholds. The calculations are based ...

How Surface Treatments Enhance Ground Handling

NASA Technical Reports Server (NTRS)

Yager, Thomas J.

2002-01-01

Several runway surface treatments developed in recent years are described in terms of how aircraft tire landing and takeoff friction requirements are met, particularly during adverse weather conditions. Changing the surface texture with grooving, grinding and shot peening, use of chemicals to remove or prevent accumulation of natural or man-made contaminants, and the use of new techniques and materials are discussed as means of improving surface friction performance. Test data are presented to illustrate the effects of runway conditions on aircraft ground performance. The severity of the problem of operating on runway surfaces which cannot provide sufficient aircraft tire friction capability is also illustrated from documented aircraft accident/incident reports. The paper concludes with recommendations for future pavement research activities.

Runway Incursion Prevention System Testing at the Wallops Flight Facility

NASA Technical Reports Server (NTRS)

Jones, Denise R.

2005-01-01

A Runway Incursion Prevention System (RIPS) integrated with a Synthetic Vision System concept (SVS) was tested at the Reno/Tahoe International Airport (RNO) and Wallops Flight Facility (WAL) in the summer of 2004. RIPS provides enhanced surface situational awareness and alerts of runway conflicts in order to prevent runway incidents while also improving operational capability. A series of test runs was conducted using a Gulfstream-V (G-V) aircraft as the test platform and a NASA test aircraft and a NASA test van as incurring traffic. The purpose of the study, from the RIPS perspective, was to evaluate the RIPS airborne incursion detection algorithms and associated alerting and airport surface display concepts, focusing on crossing runway incursion scenarios. This paper gives an overview of the RIPS, WAL flight test activities, and WAL test results.

Enhanced Airport Surface Detection Equipment Applications,

DTIC Science & Technology

1985-04-17

of runway capacity for the single mixed runway case . The ASDE display, however, provides independent position and timing information on runway...restored to within approximately 5 percent of the good visibility capacity for the single mixed runway case . The lack of identity informa- tion on the ASDE...D.C. 20591 ENGINEERING AND ECONOMICS RESEARCH, INC. Technical Support Staff Henry R. Schramm Mignonette E. Stephen A-2 I m i . . . -i , ’ ,.i

Simulator Evaluation of Runway Incursion Prevention Technology for General Aviation Operations

NASA Technical Reports Server (NTRS)

Jones, Denise R.; Prinzel, Lawrence J., III

2011-01-01

A Runway Incursion Prevention System (RIPS) has been designed under previous research to enhance airport surface operations situation awareness and provide cockpit alerts of potential runway conflict, during transport aircraft category operations, in order to prevent runway incidents while also improving operations capability. This study investigated an adaptation of RIPS for low-end general aviation operations using a fixed-based simulator at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC). The purpose of the study was to evaluate modified RIPS aircraft-based incursion detection algorithms and associated alerting and airport surface display concepts for low-end general aviation operations. This paper gives an overview of the system, simulation study, and test results.

Runway Incursion Prevention System Simulation Evaluation

NASA Technical Reports Server (NTRS)

Jones, Denise R.

2002-01-01

A Runway Incursion Prevention System (RIPS) was evaluated in a full mission simulation study at the NASA Langley Research center in March 2002. RIPS integrates airborne and ground-based technologies to provide (1) enhanced surface situational awareness to avoid blunders and (2) alerts of runway conflicts in order to prevent runway incidents while also improving operational capability. A series of test runs was conducted in a high fidelity simulator. The purpose of the study was to evaluate the RIPS airborne incursion detection algorithms and associated alerting and airport surface display concepts. Eight commercial airline crews participated as test subjects completing 467 test runs. This paper gives an overview of the RIPS, simulation study, and test results.

Mitigating runway incursions : a safety benefits assessment of airport surface moving map displays

DOT National Transportation Integrated Search

2010-01-01

Airport surface moving maps vary in the capabilities provided (e.g., the depiction of ownship position and/or traffic, the presentation of taxi route, and indicating or alerting the potential for runway incursions). The purpose of this effort was to ...

32 CFR 256.6 - Runway classification by aircraft type.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 2 2010-07-01 2010-07-01 false Runway classification by aircraft type. 256.6... type. Class A runways S-2, VC-6, C-1, C-2, TC-4C, U-10, U-11, LU-16, TU-16, HU-16, C-7, C-8, C-12, C-47...-130, A-7, A-38, AV-8, P-2, P-3, T-29, T-33, T-37, T-39, T-1, HC-130B, C-131, C-140, C-5A, KC-97, F-9...

32 CFR 256.6 - Runway classification by aircraft type.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 32 National Defense 2 2011-07-01 2011-07-01 false Runway classification by aircraft type. 256.6... type. Class A runways S-2, VC-6, C-1, C-2, TC-4C, U-10, U-11, LU-16, TU-16, HU-16, C-7, C-8, C-12, C-47...-130, A-7, A-38, AV-8, P-2, P-3, T-29, T-33, T-37, T-39, T-1, HC-130B, C-131, C-140, C-5A, KC-97, F-9...

Surface Management System Departure Event Data Analysis

NASA Technical Reports Server (NTRS)

Monroe, Gilena A.

2010-01-01

This paper presents a data analysis of the Surface Management System (SMS) performance of departure events, including push-back and runway departure events.The paper focuses on the detection performance, or the ability to detect departure events, as well as the prediction performance of SMS. The results detail a modest overall detection performance of push-back events and a significantly high overall detection performance of runway departure events. The overall detection performance of SMS for push-back events is approximately 55%.The overall detection performance of SMS for runway departure events nears 100%. This paper also presents the overall SMS prediction performance for runway departure events as well as the timeliness of the Aircraft Situation Display for Industry data source for SMS predictions.

Tire and runway surface research

NASA Technical Reports Server (NTRS)

Yager, Thomas J.

1986-01-01

The condition of aircraft tires and runway surfaces can be crucial in meeting the stringent demands of aircraft ground operations, particularly under adverse weather conditions. Gaining a better understanding of the factors influencing the tire/pavement interface is the aim of several ongoing NASA Langley research programs which are described in this paper. Results from several studies conducted at the Langley Aircraft Landing Dynamics Facility, tests with instrumented ground vehicles and aircraft, and some recent aircraft accident investigations are summarized to indicate effects of different tire and runway properties. The Joint FAA/NASA Runway Friction Program is described together with some preliminary test findings. The scope of future NASA Langley research directed towards solving aircraft ground operational problems related to the tire/pavement interface is given.

Texture Modification of the Shuttle Landing Facility Runway at Kennedy Space Center

NASA Technical Reports Server (NTRS)

Daugherty, Robert H.; Yager, Thomas J.

1997-01-01

This paper describes the test procedures and the criteria used in selecting an effective runway-surface-texture modification at the Kennedy Space Center (KSC) Shuttle Landing Facility (SLF) to reduce Orbiter tire wear. The new runway surface may ultimately result in an increase of allowable crosswinds for launch and landing operations. The modification allows launch and landing operations in 20-knot crosswinds, if desired. This 5-knot increase over the previous 15-knot limit drastically increases landing safety and the ability to make on-time launches to support missions in which Space Station rendezvous are planned. The paper presents the results of an initial (1988) texture modification to reduce tire spin-up wear and then describes a series of tests that use an instrumented ground-test vehicle to compare tire friction and wear characteristics, at small scale, of proposed texture modifications placed into the SLF runway surface itself. Based on these tests, three candidate surfaces were chosen to be tested at full-scale by using a highly modified and instrumented transport aircraft capable of duplicating full Orbiter landing profiles. The full-scale Orbiter tire testing revealed that tire wear could be reduced approximately by half with either of two candidates. The texture-modification technique using a Humble Equipment Company Skidabrader(trademark) shotpeening machine proved to be highly effective, and the entire SLF runway surface was modified in September 1994. The extensive testing and evaluation effort that preceded the selection of this particular surface-texture-modification technique is described herein.

Pegasus Airfield Repair and Protection: Laboratory Trials of White Ice Paint to Improve the Energy Reflectance Properties of the Glacial-Ice Runway Surface

DTIC Science & Technology

2015-01-01

1 Introduction The Pegasus White Ice Runway at McMurdo Station, Antarctica , has expe- rienced significant melting during the past two austral...Laboratory Trials of White Ice Paint to Improve the Energy Reflectance Properties of the Glacial- Ice Runway Surface Co ld R eg io ns R es ea rc h...ERDC/CRREL TN-15-1 January 2015 Pegasus Airfield Repair and Protection Laboratory Trials of White Ice Paint to Improve the Energy Reflectance

14 CFR 77.25 - Civil airport imaginary surfaces.

Code of Federal Regulations, 2010 CFR

2010-01-01

... (CONTINUED) AIRSPACE OBJECTS AFFECTING NAVIGABLE AIRSPACE Obstruction Standards § 77.25 Civil airport... the center of each end of the primary surface of each runway of each airport and connecting the... for either end of the runway. When a 5,000-foot arc is encompassed by tangents connecting two adjacent...

National blueprint for runway safety

DOT National Transportation Integrated Search

2000-10-01

The Blueprint describes the processes : employed to measurably reduce the risks : associated with runway incursions and surface : incidents. It sets expectations, establishes : accountability, communicates information, : and defines new and improved ...

Runway drainage characteristics related to tire friction performance

NASA Technical Reports Server (NTRS)

Yager, Thomas J.

1991-01-01

The capability of a runway pavement to rapidly drain water buildup during periods of precipitation is crucial to minimize tire hydroplaning potential and maintain adequate aircraft ground operational safety. Test results from instrumented aircraft, ground friction measuring vehicles, and NASA Langley's Aircraft Landing Dynamics Facility (ALDF) track have been summarized to indicate the adverse effects of pavement wetness conditions on tire friction performance. Water drainage measurements under a range of rainfall rates have been evaluated for several different runway surface treatments including the transversely grooved and longitudinally grinded concrete surfaces at the Space Shuttle Landing Facility (SLF) runway at NASA Kennedy Space Center in Florida. The major parameters influencing drainage rates and extent of flooding/drying conditions are identified. Existing drainage test data are compared to a previously derived empirical relationship and the need for some modification is indicated. The scope of future NASA Langley research directed toward improving empirical relationships to properly define runway drainage capability and consequently, enhance aircraft ground operational safety, is given.

Runway Safety Monitor Algorithm for Runway Incursion Detection and Alerting

NASA Technical Reports Server (NTRS)

Green, David F., Jr.; Jones, Denise R. (Technical Monitor)

2002-01-01

The Runway Safety Monitor (RSM) is an algorithm for runway incursion detection and alerting that was developed in support of NASA's Runway Incursion Prevention System (RIPS) research conducted under the NASA Aviation Safety Program's Synthetic Vision System element. The RSM algorithm provides pilots with enhanced situational awareness and warnings of runway incursions in sufficient time to take evasive action and avoid accidents during landings, takeoffs, or taxiing on the runway. The RSM currently runs as a component of the NASA Integrated Display System, an experimental avionics software system for terminal area and surface operations. However, the RSM algorithm can be implemented as a separate program to run on any aircraft with traffic data link capability. The report documents the RSM software and describes in detail how RSM performs runway incursion detection and alerting functions for NASA RIPS. The report also describes the RIPS flight tests conducted at the Dallas-Ft Worth International Airport (DFW) during September and October of 2000, and the RSM performance results and lessons learned from those flight tests.

Texture Modification of the Shuttle Landing Facility Runway at the NASA Kennedy Space Center

NASA Technical Reports Server (NTRS)

Daugherty, Robert H.; Yager, Thomas J.

1996-01-01

This paper describes the test procedures and the selection criteria used in selecting the best runway surface texture modification at the Kennedy Space Center (KSC) Shuttle Landing Facility (SLF) to reduce Orbiter tire wear. The new runway surface may ultimately result in an increase of allowable crosswinds for launch and landing operations. The modification allows launch and landing operations in 20-kt crosswinds if desired. This 5-kt increase over the previous 15-kt limit drastically increases landing safety and the ability to make on-time launches to support missions where space station rendezvous is planned.

Aluminum runway surface as possible aid to aircraft braking

NASA Technical Reports Server (NTRS)

Miller, C. D.; Pinkel, I. I.

1973-01-01

Several concepts are described for use singly or in combination to improve aircraft braking. All involve a thin layer of aluminum covering all or part of the runway. Advantage would derive from faster heat conduction from the tire-runway interface. Heating of tread surface with consequent softening and loss of friction coefficient should be reduced. Equations are developed indicating that at least 99 percent of friction heat should flow into the aluminum. Preliminary test results indicate a coefficient of sliding friction of 1.4, with predictably slight heating of tread. Elimination of conventional brakes is at least a remote possibility.

Performance of an aircraft tire under cyclic braking and of a currently operational antiskid braking system

NASA Technical Reports Server (NTRS)

Tanner, J. A.

1972-01-01

An experimental investigation was conducted to study the performance of an aircraft tire under cyclic braking conditions and to study the performance of a currently operational aircraft antiskid braking system. Dry, damp, and flooded runway surface conditions were used in the investigation. The results indicated that under cyclic braking conditions the braking and cornering-force friction coefficients may be influenced by fluctuations in the vertical load, flexibility in the wheel support, and the spring coupling between the wheel and the tire-pavement interface. The cornering capability was shown to be negligible at wheel slip ratios well below a locked-wheel skid under all test surface conditions. The maximum available brake-force friction coefficient was shown to be dependent upon the runway surface condition, upon velocity, and, for wet runways, upon tire differences. Moderate reductions in vertical load and brake system pressure did not significantly affect the overall wet-runway performance of the tire.

Functional Analysis for an Integrated Capability of Arrival/Departure/Surface Management with Tactical Runway Management

NASA Technical Reports Server (NTRS)

Phojanamongkolkij, Nipa; Okuniek, Nikolai; Lohr, Gary W.; Schaper, Meilin; Christoffels, Lothar; Latorella, Kara A.

2014-01-01

The runway is a critical resource of any air transport system. It is used for arrivals, departures, and for taxiing aircraft and is universally acknowledged as a constraining factor to capacity for both surface and airspace operations. It follows that investigation of the effective use of runways, both in terms of selection and assignment as well as the timing and sequencing of the traffic is paramount to the efficient traffic flows. Both the German Aerospace Center (DLR) and NASA have developed concepts and tools to improve atomic aspects of coordinated arrival/departure/surface management operations and runway configuration management. In December 2012, NASA entered into a Collaborative Agreement with DLR. Four collaborative work areas were identified, one of which is called "Runway Management." As part of collaborative research in the "Runway Management" area, which is conducted with the DLR Institute of Flight Guidance, located in Braunschweig, the goal is to develop an integrated system comprised of the three DLR tools - arrival, departure, and surface management (collectively referred to as A/D/S-MAN) - and NASA's tactical runway configuration management (TRCM) tool. To achieve this goal, it is critical to prepare a concept of operations (ConOps) detailing how the NASA runway management and DLR arrival, departure, and surface management tools will function together to the benefit of each. To assist with the preparation of the ConOps, the integrated NASA and DLR tools are assessed through a functional analysis method described in this report. The report first provides the highlevel operational environments for air traffic management (ATM) in Germany and in the U.S., and the descriptions of the DLR's A/D/S-MAN and NASA's TRCM tools at the level of details necessary to compliment the purpose of the study. Functional analyses of each tool and a completed functional analysis of an integrated system design are presented next in the report. Future efforts to fully develop the ConOps will include: developing scenarios to fully test environmental, procedural, and data availability assumptions; executing the analysis by a walk-through of the integrated system using these scenarios; defining the appropriate role of operators in terms of their monitoring requirements and decision authority; executing the analysis by a walk-through of the integrated system with operator involvement; characterizing the environmental, system data requirements, and operator role assumptions for the ConOps.

Development and Execution of the RUNSAFE Runway Safety Bayesian Belief Network Model

NASA Technical Reports Server (NTRS)

Green, Lawrence L.

2015-01-01

One focus area of the National Aeronautics and Space Administration (NASA) is to improve aviation safety. Runway safety is one such thrust of investigation and research. The two primary components of this runway safety research are in runway incursion (RI) and runway excursion (RE) events. These are adverse ground-based aviation incidents that endanger crew, passengers, aircraft and perhaps other nearby people or property. A runway incursion is the incorrect presence of an aircraft, vehicle or person on the protected area of a surface designated for the landing and take-off of aircraft; one class of RI events simultaneously involves two aircraft, such as one aircraft incorrectly landing on a runway while another aircraft is taking off from the same runway. A runway excursion is an incident involving only a single aircraft defined as a veer-off or overrun off the runway surface. Within the scope of this effort at NASA Langley Research Center (LaRC), generic RI, RE and combined (RI plus RE, or RUNSAFE) event models have each been developed and implemented as a Bayesian Belief Network (BBN). Descriptions of runway safety issues from the literature searches have been used to develop the BBN models. Numerous considerations surrounding the process of developing the event models have been documented in this report. The event models were then thoroughly reviewed by a Subject Matter Expert (SME) panel through multiple knowledge elicitation sessions. Numerous improvements to the model structure (definitions, node names, node states and the connecting link topology) were made by the SME panel. Sample executions of the final RUNSAFE model have been presented herein for baseline and worst-case scenarios. Finally, a parameter sensitivity analysis for a given scenario was performed to show the risk drivers. The NASA and LaRC research in runway safety event modeling through the use of BBN technology is important for several reasons. These include: 1) providing a means to clearly understand the cause and effect patterns leading to safety issues, incidents and accidents, 2) enabling the prioritization of specialty areas needing more attention to improve aviation safety, and 3) enabling the identification of gaps within NASA's Aviation Safety funding portfolio

Plastic (wire-combed) grooving of a slip-formed concrete runway overlay at Patrick Henry Airport: An initial evaluation

NASA Technical Reports Server (NTRS)

Marlin, E. C.; Horne, W. B.

1977-01-01

A wire-comb technique is described for transversely grooving the surface of a freshly laid (plastic state) slip-formed concrete overlay installed at Patrick Henry Airport. This method of surface texturing yields better water drainage and pavement skid resistance than that obtained with an older conventional burlap drag concrete surface treatment installed on an adjacent portion of the runway.

A fresh look at runway incursions: onboard surface movement awareness and alerting system based on SVS

NASA Astrophysics Data System (ADS)

Vernaleken, Christoph; Mihalic, Lamir; Güttler, Mathias; Klingauf, Uwe

2006-05-01

Increasing traffic density on the aerodrome surface due to the continuous worldwide growth in the number of flight operations does not only cause capacity and efficiency problems, but also increases the risk of serious incidents and accidents on the airport movement area. Of these, Runway Incursions are the by far most safety-critical. In fact, the worst-ever accident in civil aviation, the collision of two Boeing B747s on Tenerife in 1977 with 583 fatalities, was caused by a Runway Incursion. Therefore, various Runway Safety programs have recently been initiated around the globe, often focusing on ground-based measures such as improved surveillance. However, as a lack of flight crew situational awareness is a key causal factor in many Runway Incursion incidents and accidents, there is a strong need for an onboard solution, which should be capable of interacting cooperatively with ground-based ATM systems, such as A-SMGCS where available. This paper defines the concept of preventive and reactive Runway Incursion avoidance and describes a Surface Movement Awareness & Alerting System (SMAAS) designed to alert the flight crew if they are at risk of infringing a runway. Both the SVS flight deck displays and the corresponding alerting algorithms utilize an ED 99A/RTCA DO-272A compliant aerodrome database, as well as airport operational, traffic and clearance data received via ADS-B or other data links, respectively. The displays provide the crew with enhanced positional, operational, clearance and traffic awareness, and they are used to visualize alerts. A future enhancement of the system will provide intelligent alerting for conflicts caused by surrounding traffic.

Runway Status Lights Evaluation Report

DOT National Transportation Integrated Search

1998-09-01

The Federal Aviation Administration (FAA) conducted a proof-of-concept demonstration of the Runway Status Lights (RWSL) at Boston's Logan International Airport. The RWSL, employing a network of lights on the airport movement surface, conveys informat...

STS-29 Discovery, OV-103, lands on Edwards AFB concrete runway 22

NASA Technical Reports Server (NTRS)

1989-01-01

STS-29 Discovery, Orbiter Vehicle (OV) 103, main landing gear (MLG) touches down at a speed of approximately 205 knots (235 miles per hour) on concrete runway 22 at Edwards Air Force Base (AFB), California. Nose landing gear (NLG) is deployed and rides above runway surface prior touchdown. Mojave desert scrub brush appears in the foreground with mountain range appearing in the background.

A Concept and Implementation of Optimized Operations of Airport Surface Traffic

NASA Technical Reports Server (NTRS)

Jung, Yoon C.; Hoang, Ty; Montoya, Justin; Gupta, Gautam; Malik, Waqar; Tobias, Leonard

2010-01-01

This paper presents a new concept of optimized surface operations at busy airports to improve the efficiency of taxi operations, as well as reduce environmental impacts. The suggested system architecture consists of the integration of two decoupled optimization algorithms. The Spot Release Planner provides sequence and timing advisories to tower controllers for releasing departure aircraft into the movement area to reduce taxi delay while achieving maximum throughput. The Runway Scheduler provides take-off sequence and arrival runway crossing sequence to the controllers to maximize the runway usage. The description of a prototype implementation of this integrated decision support tool for the airport control tower controllers is also provided. The prototype decision support tool was evaluated through a human-in-the-loop experiment, where both the Spot Release Planner and Runway Scheduler provided advisories to the Ground and Local Controllers. Initial results indicate the average number of stops made by each departure aircraft in the departure runway queue was reduced by more than half when the controllers were using the advisories, which resulted in reduced taxi times in the departure queue.

Aircraft and Ground Vehicle Winter Runway Friction Assessment

NASA Technical Reports Server (NTRS)

Yager, Thomas J.

1999-01-01

Some background information is given together with the scope and objectives of a 5-year, Joint Winter Runway Friction Measurement Program between the National Aeronautics & Space Administration (NASA), Transport Canada (TC), and the Federal Aviation Administration (FAA). The primary objective of this effort is to perform instrumented aircraft and ground vehicle tests aimed at identifying a common number that all the different ground vehicle devices would report. This number, denoted the International Runway Friction Index (IRFI), will be related to all types of aircraft stopping performance. The range of test equipment, the test sites, test results and accomplishments, the extent of the substantial friction database compiled, and future test plans will be described. Several related studies have also been implemented including the effects of contaminant type on aircraft impingement drag, and the effectiveness of various runway and aircraft de-icing chemical types, and application rates.

Progress Toward Future Runway Management

NASA Technical Reports Server (NTRS)

Lohr, Gary W.; Brown, Sherilyn A.; Atkins, Stephen; Eisenhawer, Stephen W.; Bott, Terrance F.; Long, Dou; Hasan, Shahab

2011-01-01

The runway is universally acknowledged as a constraining factor to capacity in the National Airspace System (NAS). It follows that investigation of the effective use of runways, both in terms of selection and assignment, is paramount to the efficiency of future NAS operations. The need to address runway management is not a new idea; however, as the complexities of factors affecting runway selection and usage increase, the need for effective research in this area correspondingly increases. Under the National Aeronautics and Space Administration s Airspace Systems Program, runway management is a key research area. To address a future NAS which promises to be a complex landscape of factors and competing interests among users and operators, effective runway management strategies and capabilities are required. This effort has evolved from an assessment of current practices, an understanding of research activities addressing surface and airspace operations, traffic flow management enhancements, among others. This work has yielded significant progress. Systems analysis work indicates that the value of System Oriented Runway Management tools is significantly increased in the metroplex environment over that of the single airport case. Algorithms have been developed to provide runway configuration recommendations for a single airport with multiple runways. A benefits analysis has been conducted that indicates the SORM benefits include supporting traffic growth, cost reduction as a result of system efficiency, NAS optimization from metroplex operations, fairness in aircraft operations, and rational decision making.

Enhancing pilot situational awareness of the airport surface movement area

NASA Technical Reports Server (NTRS)

Jones, D. R.; Young, S. D.

1994-01-01

Two studies are being conducted to address airport surface movement area safety and capacity issues by providing enhanced situational awareness information to pilots. One study focuses on obtaining pilot opinion of the Runway Status Light System (RSLS). This system has been designed to reduce the likelihood of runway incursions by informing pilots when a runway is occupied. The second study is a flight demonstration of an rate integrated system consisting of an electronic moving map in the cockpit and display of the aircraft identification to the controller. Taxi route and hold warning information will be sent to the aircraft data link for display on the electronic moving map. This paper describes the plans for the two studies.

STS-38 Atlantis, Orbiter Vehicle (OV) 104, lands on runway 33 at KSC SLF

NASA Image and Video Library

1990-11-20

STS038-S-041 (20 Nov 1990) --- STS-38 Atlantis, Orbiter Vehicle (OV) 104, lands on runway 33 at Kennedy Space Center (KSC) Shuttle Landing Facility (SLF). The main landing gear (MLG) has just touched down on the runway surface as the nose landing gear (NLG) glides above it. The Department of Defense (DOD)-devoted mission came to an end (with complete wheel stop) at 4:43:37 pm (Eastern Standard Time (EST)).

Recent progress towards predicting aircraft ground handling performance

NASA Technical Reports Server (NTRS)

Yager, T. J.; White, E. J.

1981-01-01

Capability implemented in simulating aircraft ground handling performance is reviewed and areas for further expansion and improvement are identified. Problems associated with providing necessary simulator input data for adequate modeling of aircraft tire/runway friction behavior are discussed and efforts to improve tire/runway friction definition, and simulator fidelity are described. Aircraft braking performance data obtained on several wet runway surfaces are compared to ground vehicle friction measurements. Research to improve methods of predicting tire friction performance are discussed.

Evaluation of Winter Operational Runway Friction Measurement Equipment, Procedures, and Research

NASA Technical Reports Server (NTRS)

1995-01-01

This document produced by the FAA/Industry Winter Runway Friction Measurement and Reporting Working Group, is designed to provide an overview of current information on the present guidance, practices, and procedures for reporting runway pavement surface conditions during winter operations at airports. It contains recommendations on the desirability of providing the best procedural consistency and standardization and discusses the available means to implement the guidance that will result in improved aviation safety at airports during hazardous winter conditions.

Design and Implementation of a Consolidated Airfield at McMurdo, Antarctica

DTIC Science & Technology

2014-09-01

DESTROY THIS REPORT WHEN NO LONGER NEEDED. DO NOT RETURN IT TO THE ORIGINATOR . ERDC/CRREL TR-14-22 iii Contents Abstract...the current loca- tion of the white ice runway (the wheeled runway at Pegasus) is about 1/3 mile WSW of where it was when it was originally ...ft below the surface. This is not surprising; when the original runway was established in 1991–92, there were regions where the ice needed to be

Tomorrows' Air Transportation System Breakout Series Report

NASA Technical Reports Server (NTRS)

2001-01-01

The purpose of this presentation is to discuss tomorrow's air transportation system. Section of this presentation includes: chair comments; other general comments; surface congestion alleviation; runway productivity; enhanced arrival/departure tools; integrated airspace decision support tools; national traffic flow management, runway independent operations; ATM TFM weather; and terminal weather.

Aircraft radial-belted tire evaluation

NASA Technical Reports Server (NTRS)

Yager, Thomas J.; Stubbs, Sandy M.; Davis, Pamela A.

1990-01-01

An overview is given of the ongoing joint NASA/FAA/Industry Surface Traction And Radial Tire (START) Program being conducted at NASA Langley's Aircraft Landing Dynamics Facility (ALDF). The START Program involves tests using three different tire sizes to evaluate tire rolling resistance, braking, and cornering performance throughout the aircraft ground operational speed range for both dry and wet runway surfaces. Preliminary results from recent 40 x 14 size bias-ply, radial-belted, and H-type aircraft tire tests are discussed. The paper concludes with a summary of the current program status and planned ALDF test schedule.

Initial Concept for Terminal Area Conflict Detection, Alerting, and Resolution Capability on or Near the Airport Surface

NASA Technical Reports Server (NTRS)

Green, David F.; Otero, Sharon D.; Barker, Glover D.; Jones, Denise R.

2009-01-01

The Next Generation Air Transportation System (NextGen) concept for 2025 envisions the movement of large numbers of people and goods in a safe, efficient, and reliable manner. The NextGen will remove many of the constraints in the current air transportation system, support a wider range of operations, and deliver an overall system capacity up to 3 times that of current operating levels. In order to achieve the NextGen vision, research is necessary in the areas of surface traffic optimization, maximum runway capacity, reduced runway occupancy time, simultaneous single runway operations, and terminal area conflict prevention, among others. The National Aeronautics and Space Administration (NASA) is conducting Collision Avoidance for Airport Traffic (CAAT) research to develop technologies, data, and guidelines to enable Conflict Detection and Resolution (CD&R) in the Airport Terminal Maneuvering Area (ATMA) under current and emerging NextGen operating concepts. In this report, an initial concept for an aircraft-based method for CD&R in the ATMA is presented. This method is based upon previous NASA work in CD&R for runway incursion prevention, the Runway Incursion Prevention System (RIPS). CAAT research is conducted jointly under NASA's Airspace Systems Program, Airportal Project and the Aviation Safety Program, Integrated Intelligent Flight Deck Project.

Initial Data Analysis Results for ATD-2 ISAS HITL Simulation

NASA Technical Reports Server (NTRS)

Lee, Hanbong

2017-01-01

To evaluate the operational procedures and information requirements for the core functional capabilities of the ATD-2 project, such as tactical surface metering tool, APREQ-CFR procedure, and data element exchanges between ramp and tower, human-in-the-loop (HITL) simulations were performed in March, 2017. This presentation shows the initial data analysis results from the HITL simulations. With respect to the different runway configurations and metering values in tactical surface scheduler, various airport performance metrics were analyzed and compared. These metrics include gate holding time, taxi-out in time, runway throughput, queue size and wait time in queue, and TMI flight compliance. In addition to the metering value, other factors affecting the airport performance in the HITL simulation, including run duration, runway changes, and TMI constraints, are also discussed.

Behavior of aircraft antiskid braking systems on dry and wet runway surfaces. A slip-velocity-controlled, pressure-bias-modulated system

NASA Technical Reports Server (NTRS)

Stubbs, S. M.; Tanner, J. A.; Smith, E. G.

1979-01-01

The braking and cornering response of a slip velocity controlled, pressure bias modulated aircraft antiskid braking system is investigated. The investigation, conducted on dry and wet runway surfaces, utilized one main gear wheel, brake, and tire assembly of a McDonnell Douglas DC 9 series 10 airplane. The landing gear strut was replaced by a dynamometer. The parameters, which were varied, included the carriage speed, tire loading, yaw angle, tire tread condition, brake system operating pressure, and runway wetness conditions. The effects of each of these parameters on the behavior of the skid control system is presented. Comparisons between data obtained with the skid control system and data obtained from single cycle braking tests without antiskid protection are examined.

Wake vortex effects on parallel runway operations

DOT National Transportation Integrated Search

2003-01-06

Aircraft wake vortex behavior in ground effect between two parallel runways at Frankfurt/Main International Airport was studied. The distance and time of vortex demise were examined as a function of crosswind, aircraft type, and a measure of atmosphe...

STS-29 Discovery, OV-103, lands on Edwards AFB concrete runway 22

NASA Technical Reports Server (NTRS)

1989-01-01

STS-29 Discovery, Orbiter Vehicle (OV) 103, main landing gear (MLG) touches down at a speed of approximately 205 knots (235 miles per hour) on concrete runway 22 at Edwards Air Force Base (AFB), California. Nose landing gear (NLG) is deployed and rides above runway surface prior touchdown. Rear view captures OV-103 as it glides past photographer to wheel stop showing the tail section (speedbrake/rudder) and three space shuttle main engines (SSMEs). Mojave desert scrub brush appears in the foreground with aircraft hangar appearing in the background.

Design and Validation of an Instrumented Uneven Terrain Treadmill.

PubMed

Voloshina, Alexandra S; Ferris, Daniel P

2018-06-01

Studying human and animal locomotion on an uneven terrain can be beneficial to basic science and applied studies for clinical and robotic applications. Traditional biomechanical analysis of human locomotion has often been limited to laboratory environments with flat, smooth runways and treadmills. The authors modified a regular exercise treadmill by attaching wooden blocks to the treadmill belt to yield an uneven locomotion surface. To ensure that these treadmill modifications facilitated biomechanical measurements, the authors compared ground reaction force data collected while a subject ran on the modified instrumented treadmill with a smooth surface with data collected using a conventional instrumented treadmill. Comparisons showed only minor differences. These results suggest that adding an uneven surface to a modified treadmill is a viable option for studying human or animal locomotion on an uneven terrain. Other types of surfaces (eg, compliant blocks) could be affixed in a similar manner for studies on other types of locomotion surfaces.

Summit Station Skiway Review

DTIC Science & Technology

2013-03-01

behind a low ground pressure tractor, b) leveling with snow planes, and c) repeating the process in 0.3 m lifts. Cold sink times between each...Antarctica started in 1957 with Opera- tion Deep Freeze at Byrd and South Pole Stations and ran until 1962. (During this time McMurdo had a runway...independent turning tires with the ability to compact uniformly across a surface. This type of equipment was best suited for deep compaction because of

Abrasion behavior of aluminum and composite skin coupons, stiffened skins and stiffened panels representative of transport airplane structures

NASA Technical Reports Server (NTRS)

Jackson, K. E.

1985-01-01

A three-phase investigation was conducted to compare the friction and wear response of aluminum and graphite-epoxy composite materials when subjected to loading conditions similar to those experienced by the skin panels on the underside of a transport airplane during an emergency belly landing on a runway surface. The first phase involved a laboratory test which used a standard belt sander to provide the sliding abrasive surface. Small skin-coupon test specimens were abraded over a range of pressures and velocities to determine the effects of these variables on the coefficient of friction and wear rate. The second phase involved abrading I-beam stiffened skins on actual runway surface over the same range of pressures and velocities used in the first phase. In the third phase, large stiffened panels which most closely resembled transport fuelage skin construction were abraded on a runway surface. This report presents results from each phase of the investigation and shows comparisons between the friction and wear behavior of the aluminum and graphite-epoxy composite materials.

Field Evaluation of Ultra-High Pressure Water Systems for Runway Rubber Removal

DTIC Science & Technology

2014-04-01

ER D C/ G SL T R- 14 -1 1 Field Evaluation of Ultra-High Pressure Water Systems for Runway Rubber Removal G eo te ch ni ca l a nd S tr...Field Evaluation of Ultra-High Pressure Water Systems for Runway Rubber Removal Aaron B. Pullen Applied Research Associates, Inc. 421 Oak Avenue...collaboration with Applied Research Associates, Inc. (ARA). Several types of commercial UHPW water blasting systems were tested on an ungrooved portland cement

Initial Concept for Terminal Area Conflict Detection, Alerting, and Resolution Capability On or Near the Airport Surface, Version 2.0

NASA Technical Reports Server (NTRS)

Otero, Sharon D.; Barker, Glover D.; Jones, Denise R.

2013-01-01

The Next Generation Air Transportation System (NextGen) concept for 2025 envisions the movement of large numbers of people and goods in a safe, efficient, and reliable manner. The NextGen will remove many of the constraints in the current air transportation system, support a wider range of operations, and deliver an overall system capacity up to 3 times that of current operating levels. In order to achieve the NextGen vision, research is necessary in the areas of surface traffic optimization, maximum runway capacity, reduced runway occupancy time, simultaneous single runway operations, and terminal area conflict prevention, among others. The National Aeronautics and Space Administration (NASA) is conducting Collision Avoidance for Airport Traffic (CAAT) research to develop technologies, data, and guidelines to enable Conflict Detection and Resolution (CD&R) in the Airport Terminal Maneuvering Area (ATMA) under current and emerging NextGen operating concepts. The term ATMA was created to reflect the fact that the CD&R concept area of operation is focused near the airport within the terminal maneuvering area. In the following, an initial concept for an aircraft-based method for CD&R in the ATMA is presented. This method is based upon previous NASA work in CD&R for runway incursion prevention, the Runway Incursion Prevention System (RIPS).

Performance Evaluation of the Approaches and Algorithms Using Hamburg Airport Operations

NASA Technical Reports Server (NTRS)

Zhu, Zhifan; Okuniek, Nikolai; Gerdes, Ingrid; Schier, Sebastian; Lee, Hanbong; Jung, Yoon

2016-01-01

The German Aerospace Center (DLR) and the National Aeronautics and Space Administration (NASA) have been independently developing and testing their own concepts and tools for airport surface traffic management. Although these concepts and tools have been tested individually for European and US airports, they have never been compared or analyzed side-by-side. This paper presents the collaborative research devoted to the evaluation and analysis of two different surface management concepts. Hamburg Airport was used as a common test bed airport for the study. First, two independent simulations using the same traffic scenario were conducted; one by the DLR team using the Controller Assistance for Departure Optimization (CADEO) and the Taxi Routing for Aircraft: Creation and Controlling (TRACC) in a real-time simulation environment, and one by the NASA team based on the Spot and Runway Departure Advisor (SARDA) in a fast-time simulation environment. A set of common performance metrics was defined. The simulation results showed that both approaches produced operational benefits in efficiency, such as reducing taxi times, while maintaining runway throughput. Both approaches generated the gate pushback schedule to meet the runway schedule, such that the runway utilization was maximized. The conflict-free taxi guidance by TRACC helped avoid taxi conflicts and reduced taxiing stops, but the taxi benefit needed be assessed together with runway throughput to analyze the overall performance objective.

Performance Evaluation of the Approaches and Algorithms for Hamburg Airport Operations

NASA Technical Reports Server (NTRS)

Zhu, Zhifan; Okuniek, Nikolai; Gerdes, Ingrid; Schier, Sebastian; Lee, Hanbong; Jung, Yoon

2016-01-01

The German Aerospace Center (DLR) and the National Aeronautics and Space Administration (NASA) have been independently developing and testing their own concepts and tools for airport surface traffic management. Although these concepts and tools have been tested individually for European and US airports, they have never been compared or analyzed side-by-side. This paper presents the collaborative research devoted to the evaluation and analysis of two different surface management concepts. Hamburg Airport was used as a common test bed airport for the study. First, two independent simulations using the same traffic scenario were conducted: one by the DLR team using the Controller Assistance for Departure Optimization (CADEO) and the Taxi Routing for Aircraft: Creation and Controlling (TRACC) in a real-time simulation environment, and one by the NASA team based on the Spot and Runway Departure Advisor (SARDA) in a fast-time simulation environment. A set of common performance metrics was defined. The simulation results showed that both approaches produced operational benefits in efficiency, such as reducing taxi times, while maintaining runway throughput. Both approaches generated the gate pushback schedule to meet the runway schedule, such that the runway utilization was maximized. The conflict-free taxi guidance by TRACC helped avoid taxi conflicts and reduced taxiing stops, but the taxi benefit needed be assessed together with runway throughput to analyze the overall performance objective.

Performance Evaluation of the Approaches and Algorithms using Hamburg Airport Operations

NASA Technical Reports Server (NTRS)

Zhu, Zhifan; Lee, Hanbong; Jung, Yoon; Okuniek, Nikolai; Gerdes, Ingrid; Schier, Sebastian

2016-01-01

The German Aerospace Center (DLR) and the National Aeronautics and Space Administration (NASA) have been independently developing and testing their own concepts and tools for airport surface traffic management. Although these concepts and tools have been tested individually for European and US airports, they have never been compared or analyzed side-by-side. This paper presents the collaborative research devoted to the evaluation and analysis of two different surface management concepts. Hamburg Airport was used as a common test bed airport for the study. First, two independent simulations using the same traffic scenario were conducted: one by the DLR team using the Controller Assistance for Departure Optimization (CADEO) and the Taxi Routing for Aircraft58; Creation and Controlling (TRACC) in a real-time simulation environment, and one by the NASA team based on the Spot and Runway Departure Advisor (SARDA) in a fast-time simulation environment. A set of common performance metrics was defined. The simulation results showed that both approaches produced operational benefits in efficiency, such as reducing taxi times, while maintaining runway throughput. Both approaches generated the gate pushback schedule to meet the runway schedule, such that the runway utilization was maximized. The conflict-free taxi guidance by TRACC helped avoid taxi conflicts and reduced taxiing stops, but the taxi benefit needed be assessed together with runway throughput to analyze the overall performance objective.

NASA tire/runway friction projects

NASA Technical Reports Server (NTRS)

Yager, Thomas J.

1995-01-01

The paper reviews several aspects of NASA Langley Research Center's tire/runway friction evaluations directed towards improving the safety and economy of aircraft ground operations. The facilities and test equipment used in implementing different aircraft tire friction studies and other related aircraft ground performance investigations are described together with recent workshop activities at NASA Wallops Flight Facility. An overview of the pending Joint NASA/Transport Canada/FM Winter Runway Friction Program is given. Other NASA ongoing studies and on-site field tests are discussed including tire wear performance and new surface treatments. The paper concludes with a description of future research plans.

Increasing airport capacity with modified IFR approach procedures for close-spaced parallel runways

DOT National Transportation Integrated Search

2001-01-01

Because of wake turbulence considerations, current instrument approach : procedures treat close-spaced (i.e., less than 2,500 feet apart) parallel run : ways as a single runway. This restriction is designed to assure safety for all : aircraft types u...

Runway Incursion Prevention: A Technology Solution

NASA Technical Reports Server (NTRS)

Young, Steven D.; Jones, Denise R.

2001-01-01

A runway incursion occurs any time an airplane, vehicle, person or object on the ground creates a collision hazard with an airplane that is taking off or landing at an airport under the supervision of Air Traffic Control (ATC). Despite the best efforts of the Federal Aviation Administration (FAA), runway incursions continue to occur more frequently. The number of incursions reported in the U.S. rose from 186 in 1993 to 431 in 2000, an increase of 132 percent. Recently, the National Transportation Safety Board (NTSB) has made specific recommendations for reducing runway incursions including a recommendation that the FAA require, at all airports with scheduled passenger service, a ground movement safety system that will prevent runway incursions; the system should provide a direct warning capability to flight crews. To this end, NASA and its industry partners have developed an advanced surface movement guidance and control system (A-SMGCS) architecture and operational concept that are designed to prevent runway incursions while also improving operational capability. This operational concept and system design have been tested in both full-mission simulation and operational flight test experiments at major airport facilities. Anecdotal, qualitative, and specific quantitative results will be presented along with an assessment of technology readiness with respect to equipage.

Assessing Tactical Scheduler Options for Time-Based Surface Metering

NASA Technical Reports Server (NTRS)

Zelinski, Shannon; Windhorst, Robert

2017-01-01

NASA is committed to demonstrating a concept of integrated arrival, departure, and surface operations by 2020 under the Airspace Technology Demonstration 2 (ATD2) sub-project. This will be accomplished starting with a demonstration of flight specific time-based departure metering at Charlotte Douglass International Airport (CLT). ATD2 tactical metering capability is based on NASAs Spot And Runway Departure Advisor (SARDA) which has been tested successfully in human-in-the-loop simulations of CLT. SARDA makes use of surface surveillance data and surface modeling to estimate the earliest takeoff time for each flight active on the airport surface or ready for pushback from the gate. The system then schedules each flight to its assigned runway in order of earliest takeoff time and assigns a target pushback time, displayed to ramp controllers as an advisory gate hold time. The objective of this method of departure metering is to move as much delay as possible to the gate to minimize surface congestion and engine on-time, while keeping sufficient pressure on the runway to maintain throughput. This flight specific approached enables greater flight efficiency and predictability, facilitating trajectory-based operations and surface-airspace integration, which ATD2 aims to achieve.Throughout ATD2 project formulation and system development, researchers have continuously engaged with stakeholders and future users, uncovering key system requirements for tactical metering that SARDA did not address. The SARDA scheduler is updated every 10 seconds using real-time surface surveillance data to ensure the most up-to-date information is used to predict runway usage. However, rapid updates also open the potential for fluctuating advisories, which Ramp controllers at a busy airport like CLT find unacceptable. Therefore, ATD2 tactical metering requires that all advisories freeze once flights are ready so that Ramp controllers may communicate a single hold time when responding to pilot ready calls.

SARDA Surface Schedulers

NASA Technical Reports Server (NTRS)

Malik, Waqar

2016-01-01

Provide an overview of algorithms used in SARDA (Spot and Runway Departure Advisor) HITL (Human-in-the-Loop) simulation for Dallas Fort-Worth International Airport and Charlotte Douglas International airport. Outline a multi-objective dynamic programming (DP) based algorithm that finds the exact solution to the single runway scheduling (SRS) problem, and discuss heuristics to restrict the search space for the DP based algorithm and provide improvements.

Taxi Time Prediction at Charlotte Airport Using Fast-Time Simulation and Machine Learning Techniques

NASA Technical Reports Server (NTRS)

Lee, Hanbong

2016-01-01

Accurate taxi time prediction is required for enabling efficient runway scheduling that can increase runway throughput and reduce taxi times and fuel consumptions on the airport surface. Currently NASA and American Airlines are jointly developing a decision-support tool called Spot and Runway Departure Advisor (SARDA) that assists airport ramp controllers to make gate pushback decisions and improve the overall efficiency of airport surface traffic. In this presentation, we propose to use Linear Optimized Sequencing (LINOS), a discrete-event fast-time simulation tool, to predict taxi times and provide the estimates to the runway scheduler in real-time airport operations. To assess its prediction accuracy, we also introduce a data-driven analytical method using machine learning techniques. These two taxi time prediction methods are evaluated with actual taxi time data obtained from the SARDA human-in-the-loop (HITL) simulation for Charlotte Douglas International Airport (CLT) using various performance measurement metrics. Based on the taxi time prediction results, we also discuss how the prediction accuracy can be affected by the operational complexity at this airport and how we can improve the fast time simulation model before implementing it with an airport scheduling algorithm in a real-time environment.

Surface operations usability study utilizing Capstone phase I avionics : quick look report

DOT National Transportation Integrated Search

2000-10-07

Evaluate usability, suitability and acceptability of of the surface moving map implemented within Capstone Phase 1 Avionics for surface operations : Task 1: Airport Surface Situational Awareness (ASSA) : Task 2: Surface-Final Approach Runway Occupanc...

Probabilistic computer model of optimal runway turnoffs

NASA Technical Reports Server (NTRS)

Schoen, M. L.; Preston, O. W.; Summers, L. G.; Nelson, B. A.; Vanderlinden, L.; Mcreynolds, M. C.

1985-01-01

Landing delays are currently a problem at major air carrier airports and many forecasters agree that airport congestion will get worse by the end of the century. It is anticipated that some types of delays can be reduced by an efficient optimal runway exist system allowing increased approach volumes necessary at congested airports. A computerized Probabilistic Runway Turnoff Model which locates exits and defines path geometry for a selected maximum occupancy time appropriate for each TERPS aircraft category is defined. The model includes an algorithm for lateral ride comfort limits.

Surface properties-vehicle interaction

NASA Astrophysics Data System (ADS)

Huft, D. L.; Her, I.; Agrawal, S. K.; Zimmer, R. A.; Bester, C. J.

Several topics related to the surface properties of aircraft runways are discussed. The South Dakota profilometer; development of a data acquisition method for noncontact pavement macrotexture measurement; the traction of an aircraft tire on grooved and porous asphaltic concrete; holes in the pavements; the effect of pavement type and condition on the fuel consumption of vehicles; the traction loss of a suspended tire on a sinusoidal road; the effect of vehicle and driver characteristics on the psychological evaluation of road roughness; the correlation of subjective panel ratings of pavement ride quality with profilometer-derived measures of pavement roughness; a microprocessor-based noncontact distance measuring control system, and, the representation of pavement surface topography in predicting runoff depths and hydroplaning potential are discussed.

STS-53 Discovery, Orbiter Vehicle (OV) 103, lands on runway 22 at EAFB, Calif

NASA Image and Video Library

1992-12-09

STS-53 Discovery, Orbiter Vehicle (OV) 103, is slowed by a red, white, and blue drag chute during its landing on concrete runway 22 at Edwards Air Force Base (EAFB), California. Main landing gear (MLG) touchdown occurred at 12:43:17 pm (Pacific Standard Time (PST)). This aft view of OV-103 shows the drag chute deployed from its compartment at the base of the vertical tail, the speedbrake/rudder flaps open, and the space shuttle main engines (SSMEs). Both MLG and nose landing gear (NLG) ride along the runway surface. Desert scrub brush appears in the foreground and mountains are seen in the background.

Integrated Display System for Low Visibility Landing and Surface Operations

NASA Technical Reports Server (NTRS)

Beskenis, Sharon Otero; Green, David F., Jr.; Hyer, Paul V.; Johnson, Edward J., Jr.

1998-01-01

This report summarizes the software products and system architectures developed by Lockheed Martin in support of the Low Visibility Landing and Surface Operations (LVLASO) program at NASA Langley Research Center. It presents an overview of the technical aspects, capabilities, and system integration issues associated with an integrated display system (IDS) that collects, processes and presents information to an aircraft flight crew during all phases of landing, roll-out, turn-off, inbound taxi, outbound taxi and takeoff. Communications hardware, drivers, and software provide continuous real-time data at varying rates and from many different sources to the display programs for presentation on a head-down display (HDD) and/or a head-up display (HUD). An electronic moving map of the airport surface is implemented on the HDD which includes the taxi route assigned by air traffic control, a text messaging system, and surface traffic and runway status information. Typical HUD symbology for navigation and control of the aircraft is augmented to provide aircraft deceleration guidance after touchdown to a pilot selected exit and taxi guidance along the route assigned by ATC. HUD displays include scene-linked symbolic runways, runway exits and taxiways that are conformal with the actual locations on the airport surface. Display formats, system architectures, and the various IDS programs are discussed.

Economic utilization of general aviation airport runways

NASA Technical Reports Server (NTRS)

Piper, R. R.

1971-01-01

The urban general aviation airport economics is studied in detail. The demand for airport services is discussed, and the different types of users are identified. The direct cost characteristics of the airport are summarized; costs to the airport owner are largely fixed, and, except at certain large airports, weight is not a significant factor in airport costs. The efficient use of an existing airport facility is explored, with the focus on the social cost of runway congestion as traffic density at the airport build up and queues form. The tradeoff between aircraft operating costs and airport costs is analyzed in terms of runway length. The transition from theory to practice is treated, and the policy of charging prices only on aircraft storage and fuel is felt likely to continue. Implications of the study from the standpoint of public policy include pricing that spreads traffic peaks to improve runway utilization, and pricing that discriminates against aircraft requiring long runways and causes owners to adopt V/STOL equipment.

Model experiments to evaluate vortex dissipation devices proposed for installation on or near aircraft runways

NASA Technical Reports Server (NTRS)

Kohl, R. E.

1973-01-01

The effectiveness of various vortex dissipation devices proposed for installation on or near aircraft runways is evaluated on basis of results of experiments conducted with a 0.03-scale model of a Boeing 747 transport aircraft in conjunction with a simulated runway. The test variables included type of vortex dissipation device, mode of operation of the powered devices, and altitude, lift coefficient and speed of the generating aircraft. A total of fifteen devices was investigated. The evaluation is based on time sequence photographs taken in the vertical and horizontal planes during each run.

Cornering characteristics of a 40 by 14-16 type 7 aircraft tire and a comparison with characteristics of a C40 by 14-21 cantilever aircraft tire

NASA Technical Reports Server (NTRS)

Tanner, J. A.; Dreher, R. C.

1973-01-01

An investigation was conducted at the Langley aircraft landing loads and traction facility to determine the cornering characteristics of a 40 x 14-16 type VII aircraft tire. These characteristics, which include the cornering-force and drag-force friction coefficients and self-alining torque, were obtained for the tire operating on dry, damp and flooded runway surfaces over a range of yaw angles from 0 deg to 20 deg and at ground speeds from 5 to 100 knots, both with and without braking. The results of this investigation indicated that the cornering capability of the 40 x 14-16 type VII aircraft tire is degraded by high ground speeds, thin-film lubrication and tire hydroplaning effects on the wet surfaces, and brake torque. The cornering capability is greatly diminished when locked-wheel skids are encountered.

Performance Evaluation of Individual Aircraft Based Advisory Concept for Surface Management

NASA Technical Reports Server (NTRS)

Gupta, Gautam; Malik, Waqar; Tobias, Leonard; Jung, Yoon; Hong, Ty; Hayashi, Miwa

2013-01-01

Surface operations at airports in the US are based on tactical operations, where departure aircraft primarily queue up and wait at the departure runways. NASA's Spot And Runway Departure Advisor (SARDA) tool was developed to address these inefficiencies through Air Traffic Control Tower advisories. The SARDA system is being updated to include collaborative gate hold, either tactically or strategically. This paper presents the results of the human-in-the-loop evaluation of the tactical gate hold version of SARDA in a 360 degree simulated tower setting. The simulations were conducted for the east side of the Dallas/Fort Worth airport. The new system provides gate hold, ground controller and local controller advisories based on a single scheduler. Simulations were conducted with SARDA on and off, the off case reflecting current day operations with no gate hold. Scenarios based on medium (1.2x current levels) and heavy (1.5x current levels) traffic were explored. Data collected from the simulation was analyzed for runway usage, delay for departures and arrivals, and fuel consumption. Further, Traffic Management Initiatives were introduced for a subset of the aircraft. Results indicated that runway usage did not change with the use of SARDA, i.e., there was no loss in runway throughput as compared to baseline. Taxiing delay was significantly reduced with the use of advisory by 45% in medium scenarios and 60% in heavy. Arrival delay was unaffected by the use of advisory. Total fuel consumption was also reduced by 23% in medium traffic and 33% in heavy. TMI compliance appeared unaffected by the advisory

Performance Evaluation of SARDA: An Individual Aircraft-Based Advisory Concept for Surface Management

NASA Technical Reports Server (NTRS)

Jung, Yoon; Malik, Waqar; Tobias, Leonard; Gupta, Gautam; Hoang, Ty; Hayashi, Miwa

2015-01-01

Surface operations at airports in the US are based on tactical operations, where departure aircraft primarily queue up and wait at the departure runways. NASAs Spot And Runway Departure Advisor (SARDA) tool was developed to address these inefficiencies through Air Traffic Control Tower advisories. The SARDA system is being updated to include collaborative gate hold, either tactically or strategically. This paper presents the results of the human-in-the-loop evaluation of the tactical gate hold version of SARDA in a 360 degree simulated tower setting. The simulations were conducted for the east side of the Dallas-Fort Worth airport. The new system provides gate hold, ground controller and local controller advisories based on a single scheduler. Simulations were conducted with SARDA on and off, the off case reflecting current day operations with no gate hold. Scenarios based on medium (1.2x current levels) and heavy (1.5x current levels) traffic were explored. Data collected from the simulation was analyzed for runway usage, delay for departures and arrivals, and fuel consumption. Further, Traffic Management Initiatives were introduced for a subset of the aircraft. Results indicated that runway usage did not change with the use of SARDA, i.e., there was no loss in runway throughput as compared to baseline. Taxiing delay was significantly reduced with the use of advisory by 45 in medium scenarios and 60 in heavy. Arrival delay was unaffected by the use of advisory. Total fuel consumption was also reduced by 23 in medium traffic and 33 in heavy. TMI compliance appeared unaffected by the advisory.

Spot and Runway Departure Advisor

NASA Technical Reports Server (NTRS)

Jung, Yoon Chul

2013-01-01

The Spot and Runway Departure Advisor (SARDA) is a research prototype of a decision support tool for ATC tower controllers to assist in manging and controlling traffic on the surface of an airport. SARDA employs a scheduler to generate an optimal runway schedule and gate push-back - spot release sequence and schedule that improves efficiency of surface operations. The advisories for ATC tower controllers are displayed on an Electronic Flight Strip (EFS) system. The human-in-the-loop simulation of the SARDA tool was conducted for east operations of Dallas-Ft. Worth International Airport (DFW) to evaluate performance of the SARDA tool and human factors, such as situational awareness and workload. The results indicates noticeable taxi delay reduction and fuel savings by using the SARDA tool. Reduction in controller workload were also observed throughout the scenario runs. The future plan includes modeling and simulation of the ramp operations of the Charlotte International Airport, and develop a decision support tool for the ramp controllers.

A Model for Space Shuttle Orbiter Tire Side Forces Based on NASA Landing Systems Research Aircraft Test Results

NASA Technical Reports Server (NTRS)

Carter, John F.; Nagy, Christopher J.; Barnicki, Joseph S.

1997-01-01

Forces generated by the Space Shuttle orbiter tire under varying vertical load, slip angle, speed, and surface conditions were measured using the Landing System Research Aircraft (LSRA). Resulting data were used to calculate a mathematical model for predicting tire forces in orbiter simulations. Tire side and drag forces experienced by an orbiter tire are cataloged as a function of vertical load and slip angle. The mathematical model is compared to existing tire force models for the Space Shuttle orbiter. This report describes the LSRA and a typical test sequence. Testing methods, data reduction, and error analysis are presented. The LSRA testing was conducted on concrete and lakebed runways at the Edwards Air Force Flight Test Center and on concrete runways at the Kennedy Space Center (KSC). Wet runway tire force tests were performed on test strips made at the KSC using different surfacing techniques. Data were corrected for ply steer forces and conicity.

Attentional Capture by Superimposed Symbology: Boundary Conditions

NASA Technical Reports Server (NTRS)

McCann, Robert S.; Foyle, David C.; Johnston, James C.; Sridhar, Banavar (Technical Monitor)

1995-01-01

We report new results from an ongoing set of experiments in which subjects view a computer-generated display consisting of a set of stationary symbols (e.g., a "HUD") superimposed on a dynamic view of a runway as it appears to the pilot during final approach. Previous work (McCann, Foyle, & Johnston, 1993) has shown that when subjects process a cueing stimulus and then identify a geometric target, performance is slower when the cue appears on the HUD and the target appears on the runway surface, compared to a control condition where the cue and target are both on the runway surface. This "shift cost" was taken as evidence that the HUD captures attention, which then has to be shifted to the "out-the-world" scene before the target can be identified. New experiments show that the shift cost is eliminated when the cue occupies a known, fixed location on the HUD. Implications for the conditions that produce attentional tunneling are discussed.

Benefits Assessment for Tactical Runway Configuration Management Tool

NASA Technical Reports Server (NTRS)

Oseguera-Lohr, Rosa; Phojanamongkolkij, Nipa; Lohr, Gary; Fenbert, James W.

2013-01-01

The Tactical Runway Configuration Management (TRCM) software tool was developed to provide air traffic flow managers and supervisors with recommendations for airport configuration changes and runway usage. The objective for this study is to conduct a benefits assessment at Memphis (MEM), Dallas Fort-Worth (DFW) and New York's John F. Kennedy (JFK) airports using the TRCM tool. Results from simulations using the TRCM-generated runway configuration schedule are compared with results using historical schedules. For the 12 days of data used in this analysis, the transit time (arrival fix to spot on airport movement area for arrivals, or spot to departure fix for departures) for MEM departures is greater (7%) than for arrivals (3%); for JFK, there is a benefit for arrivals (9%) but not for departures (-2%); for DFW, arrivals show a slight benefit (1%), but this is offset by departures (-2%). Departure queue length benefits show fewer aircraft in queue for JFK (29%) and MEM (11%), but not for DFW (-13%). Fuel savings for surface operations at MEM are seen for both arrivals and departures. At JFK there are fuel savings for arrivals, but these are offset by increased fuel use for departures. In this study, no surface fuel benefits resulted for DFW. Results suggest that the TRCM algorithm requires modifications for complex surface traffic operations that can cause taxi delays. For all three airports, the average number of changes in flow direction (runway configuration) recommended by TRCM was many times greater than the historical data; TRCM would need to be adapted to a particular airport's needs, to limit the number of changes to acceptable levels. The results from this analysis indicate the TRCM tool can provide benefits at some high-capacity airports. The magnitude of these benefits depends on many airport-specific factors and would require adaptation of the TRCM tool; a detailed assessment is needed prior to determining suitability for a particular airport.

Guidance and Control Design for High-Speed Rollout and Turnoff (ROTO)

NASA Technical Reports Server (NTRS)

Goldthorpe, S. H.; Dangaran, R. D.; Dwyer, J. P.; McBee, L. S.; Norman, R. M.; Shannon, J. H.; Summers, L. G.

1996-01-01

A ROTO architecture, braking and steering control law and display designs for a research high speed Rollout and Turnoff (ROTO) system applicable to transport class aircraft are described herein. Minimum surface friction and FMS database requirements are also documented. The control law designs were developed with the aid of a non-real time simulation program incorporating airframe and gear dynamics as well as steering and braking guidance algorithms. An attainable objective of this ROTO system, as seen from the results of this study, is to assure that the studied aircraft can land with runway occupancy times less then 53 seconds. Runway occupancy time is measured from the time the aircraft crosses the runway threshold until its wing tip clears the near side of the runway. Turnoff ground speeds of 70 knots onto 30 degree exits are allowed with dry and wet surface conditions. Simulation time history and statistical data are documented herein. Parameters which were treated as variables in the simulation study include aircraft touchdown weight/speed/location, aircraft CG, runway friction, sensor noise and winds. After further design and development of the ROTO control system beyond the system developed earlier, aft CG MD-11 aircraft no longer require auto-asymmetric braking (steering) and fly-by-wire nose gear steering. However, the auto ROTO nose gear hysteresis must be less than 2 degrees. The 2 sigma dispersion certified for MD-11 CATIIIB is acceptable. Using this longitudinal dispersion, three ROTO exits are recommended at 3300, 4950 and 6750 feet past the runway threshold. The 3300 foot exit is required for MD-81 class aircraft. Designs documented in this report are valid for the assumptions/models used in this simulation. It is believed that the results will apply to the general class of transport aircraft; however further effort is required to validate this assumption for the general case.

Evaluation of Ultra High Molecular Weight (UHMW) Polyethylene Panels for Aircraft Arresting Systems

DTIC Science & Technology

2009-08-01

cables. When concrete or asphalt is used directly under the cables, the pavement surface becomes heavily damaged during a short period of time...the sealant and panels, and improving the performance of the asphalt and concrete mixtures adjacent to the panels. DISCLAIMER: The contents of...panels on Runway 34 at Elmendorf AFB.....................22 Figure 25. Some damage to the asphalt mixture adjacent to the concrete strip on Runway 34

Terminal Area Procedures for Paired Runways

NASA Technical Reports Server (NTRS)

Lozito, Sandra; Verma, Savita Arora

2011-01-01

Parallel runway operations have been found to increase capacity within the National Airspace but poor visibility conditions reduce the use of these operations. The NextGen and SESAR Programs have identified the capacity benefits from increased use of closely-space parallel runway. Previous research examined the concepts and procedures related to parallel runways however, there has been no investigation of the procedures associated with the strategic and tactical pairing of aircraft for these operations. This simulation study developed and examined the pilot and controller procedures and information requirements for creating aircraft pairs for parallel runway operations. The goal was to achieve aircraft pairing with a temporal separation of 15s (+/- 10s error) at a coupling point that was about 12 nmi from the runway threshold. Two variables were explored for the pilot participants: two levels of flight deck automation (current-day flight deck automation and auto speed control future automation) as well as two flight deck displays that assisted in pilot conformance monitoring. The controllers were also provided with automation to help create and maintain aircraft pairs. Results show the operations in this study were acceptable and safe. Subjective workload, when using the pairing procedures and tools, was generally low for both controllers and pilots, and situation awareness was typically moderate to high. Pilot workload was influenced by display type and automation condition. Further research on pairing and off-nominal conditions is required however, this investigation identified promising findings about the feasibility of closely-spaced parallel runway operations.

Non-airborne conflicts: The causes and effects of runway transgressions

NASA Technical Reports Server (NTRS)

Tarrel, Richard J.

1985-01-01

The 1210 ASRS runway transgression reports are studied and expanded to yield descriptive statistics. Additionally, a one of three subset was studied in detail for purposes of evaluating the causes, risks, and consequences behind trangression events. Occurrences are subdivided by enabling factor and flight phase designations. It is concluded that a larger risk of collision is associated with controller enabled departure transgressions over all other categories. The influence of this type is especially evident during the period following the air traffic controllers' strike of 1981. Causal analysis indicates that, coincidentally, controller enabled departure transgressions also, show the strongest correlations between causal factors. It shows that departure errors occur more often when visibility is reduced, and when multiple takeoff runways or intersection takeoffs are employed. In general, runway transgressions attributable to both pilot and controller errors arise from three problem areas: information transfer, awareness, and spatial judgement. Enhanced awareness by controllers will probably reduce controller enabled incidents.

Airport Traffic Conflict Detection and Resolution Algorithm Evaluation

NASA Technical Reports Server (NTRS)

Jones, Denise R.; Chartrand, Ryan C.; Wilson, Sara R.; Commo, Sean A.; Ballard, Kathryn M.; Otero, Sharon D.; Barker, Glover D.

2016-01-01

Two conflict detection and resolution (CD&R) algorithms for the terminal maneuvering area (TMA) were evaluated in a fast-time batch simulation study at the National Aeronautics and Space Administration (NASA) Langley Research Center. One CD&R algorithm, developed at NASA, was designed to enhance surface situation awareness and provide cockpit alerts of potential conflicts during runway, taxi, and low altitude air-to-air operations. The second algorithm, Enhanced Traffic Situation Awareness on the Airport Surface with Indications and Alerts (SURF IA), was designed to increase flight crew awareness of the runway environment and facilitate an appropriate and timely response to potential conflict situations. The purpose of the study was to evaluate the performance of the aircraft-based CD&R algorithms during various runway, taxiway, and low altitude scenarios, multiple levels of CD&R system equipage, and various levels of horizontal position accuracy. Algorithm performance was assessed through various metrics including the collision rate, nuisance and missed alert rate, and alert toggling rate. The data suggests that, in general, alert toggling, nuisance and missed alerts, and unnecessary maneuvering occurred more frequently as the position accuracy was reduced. Collision avoidance was more effective when all of the aircraft were equipped with CD&R and maneuvered to avoid a collision after an alert was issued. In order to reduce the number of unwanted (nuisance) alerts when taxiing across a runway, a buffer is needed between the hold line and the alerting zone so alerts are not generated when an aircraft is behind the hold line. All of the results support RTCA horizontal position accuracy requirements for performing a CD&R function to reduce the likelihood and severity of runway incursions and collisions.

KENNEDY SPACE CENTER, FLA. -- A new control tower is nearing completion at the KSC Shuttle Landing Facility. It will replace the old tower in use since 1987. The old tower stands only 20 feet above the runway surface, too low to see the launch pads to the east. During nighttime landing operations, those inside the tower have been hindered by the eight-billion candlepower xenon lights that illuminate the runway. The new control tower is built atop an existing mound, rising nearly 100 feet over the midpoint of the runway. The height gives controllers a spectacular 360-degree view of NASA-KSC and northern Brevard County. The new facility will also replace the SLF Operations Building. The operations building is home to the Military Radar Unit that monitors NASA-KSC airspace 24 hours a day, as well as runway light controls, navigational aids, weather and wind speed instrumentation, and gate controls. In the new tower, the computer displays will be fully modernized to Federal Aviation Administration standards with touch-screen technology. Construction on the new facility began in February 2003 and is nearly ready for occupancy. Only some final inspections and approvals remain. A support building and Public Affairs viewing deck, to be used for observing future landing operations, will be added and are already in work.

NASA Image and Video Library

2003-12-17

KENNEDY SPACE CENTER, FLA. -- A new control tower is nearing completion at the KSC Shuttle Landing Facility. It will replace the old tower in use since 1987. The old tower stands only 20 feet above the runway surface, too low to see the launch pads to the east. During nighttime landing operations, those inside the tower have been hindered by the eight-billion candlepower xenon lights that illuminate the runway. The new control tower is built atop an existing mound, rising nearly 100 feet over the midpoint of the runway. The height gives controllers a spectacular 360-degree view of NASA-KSC and northern Brevard County. The new facility will also replace the SLF Operations Building. The operations building is home to the Military Radar Unit that monitors NASA-KSC airspace 24 hours a day, as well as runway light controls, navigational aids, weather and wind speed instrumentation, and gate controls. In the new tower, the computer displays will be fully modernized to Federal Aviation Administration standards with touch-screen technology. Construction on the new facility began in February 2003 and is nearly ready for occupancy. Only some final inspections and approvals remain. A support building and Public Affairs viewing deck, to be used for observing future landing operations, will be added and are already in work.

KENNEDY SPACE CENTER, FLA. -- The existing control tower seen here at the edge of the KSC Shuttle Landing Facility is being replaced. In use since 1987, the old tower stands only 20 feet above the runway surface, too low to see the launch pads to the east. During nighttime landing operations, those inside the tower have been hindered by the eight-billion candlepower xenon lights that illuminate the runway. The new control tower is built atop an existing mound, rising nearly 100 feet over the midpoint of the runway. The height gives controllers a spectacular 360-degree view of NASA-KSC and northern Brevard County. The new facility will also replace the SLF Operations Building. The operations building is home to the Military Radar Unit that monitors NASA-KSC airspace 24 hours a day, as well as runway light controls, navigational aids, weather and wind speed instrumentation, and gate controls. In the new tower, the computer displays will be fully modernized to Federal Aviation Administration standards with touch-screen technology. Construction on the new facility began in February 2003 and is nearly ready for occupancy. Only some final inspections and approvals remain. A support building and Public Affairs viewing deck, to be used for observing future landing operations, will be added and are already in work.

NASA Image and Video Library

2003-12-17

KENNEDY SPACE CENTER, FLA. -- The existing control tower seen here at the edge of the KSC Shuttle Landing Facility is being replaced. In use since 1987, the old tower stands only 20 feet above the runway surface, too low to see the launch pads to the east. During nighttime landing operations, those inside the tower have been hindered by the eight-billion candlepower xenon lights that illuminate the runway. The new control tower is built atop an existing mound, rising nearly 100 feet over the midpoint of the runway. The height gives controllers a spectacular 360-degree view of NASA-KSC and northern Brevard County. The new facility will also replace the SLF Operations Building. The operations building is home to the Military Radar Unit that monitors NASA-KSC airspace 24 hours a day, as well as runway light controls, navigational aids, weather and wind speed instrumentation, and gate controls. In the new tower, the computer displays will be fully modernized to Federal Aviation Administration standards with touch-screen technology. Construction on the new facility began in February 2003 and is nearly ready for occupancy. Only some final inspections and approvals remain. A support building and Public Affairs viewing deck, to be used for observing future landing operations, will be added and are already in work.

Chevron cutting: Experiment with new runway mixtures

NASA Technical Reports Server (NTRS)

Tyran, K. (Compiler)

1978-01-01

Chevron cutting is shown to occur in different forms depending on the type of tire and the rubber on the running surface. Hardest wear is shown by the main tires of the B-747. Four defects occurred, in the form of two rip separation and two breakouts of the running surface. Tires capped by Thompson are more affected than any of the other rubber-capping fabrics. For Thompson tires, Chevron Cutting is greatly reduced with a fiberglass-rubber mixture. For Goodyear tires, it is eliminated with spiral wrap rubbercapping; resistance to damages through cuts seems to be more positive for Goodyear tires. For Mader tires, the extent of Chevron Cutting is generally smaller than for Thompson cappings.

Benefits Assessment for Single-Airport Tactical Runway Configuration Management Tool (TRCM)

NASA Technical Reports Server (NTRS)

Oseguera-Lohr, Rosa; Phojanamonogkolkij, Nipa; Lohr, Gary W.

2015-01-01

The System-Oriented Runway Management (SORM) concept was developed as part of the Airspace Systems Program (ASP) Concepts and Technology Development (CTD) Project, and is composed of two basic capabilities: Runway Configuration Management (RCM), and Combined Arrival/Departure Runway Scheduling (CADRS). RCM is the process of designating active runways, monitoring the active runway configuration for suitability given existing factors, and predicting future configuration changes; CADRS is the process of distributing arrivals and departures across active runways based on local airport and National Airspace System (NAS) goals. The central component in the SORM concept is a tool for taking into account all the various factors and producing a recommendation for what would be the optimal runway configuration, runway use strategy, and aircraft sequence, considering as many of the relevant factors required in making this type of decision, and user preferences, if feasible. Three separate tools were initially envisioned for this research area, corresponding to the time scale in which they would operate: Strategic RCM (SRCM), with a planning horizon on the order of several hours, Tactical RCM (TRCM), with a planning horizon on the order of 90 minutes, and CADRS, with a planning horizon on the order of 15-30 minutes[1]. Algorithm development was initiated in all three of these areas, but the most fully developed to date is the TRCM algorithm. Earlier studies took a high-level approach to benefits, estimating aggregate benefits across most of the major airports in the National Airspace Systems (NAS), for both RCM and CADRS [2]. Other studies estimated the benefit of RCM and CADRS using various methods of re-sequencing arrivals to reduce delays3,4, or better balancing of arrival fixes5,6. Additional studies looked at different methods for performing the optimization involved in selecting the best Runway Configuration Plan (RCP) to use7-10. Most of these previous studies were high-level or generic in nature (not focusing on specific airports), and benefits were aggregated for the entire NAS, with relatively low fidelity simulation of SORM functions and aircraft trajectories. For SORM research, a more detailed benefits assessment of RCM and CADRS for specific airports or metroplexes is needed.

Airplane takeoff and landing performance monitoring system

NASA Technical Reports Server (NTRS)

Middleton, David B. (Inventor); Srivatsan, Raghavachari (Inventor); Person, Jr., Lee H. (Inventor)

1991-01-01

The invention is a real-time takeoff and landing performance monitoring system for an aircraft which provides a pilot with graphic and metric information to assist in decisions related to achieving rotation speed (V.sub.R) within the safe zone of a runway, or stopping the aircraft on the runway after landing or take-off abort. The system processes information in two segments: a pretakeoff segment and a real-time segment. One-time inputs of ambient conditions and airplane configuration information are used in the pretakeoff segment to generate scheduled performance data. The real-time segment uses the scheduled performance data, runway length data and transducer measured parameters to monitor the performance of the airplane throughout the takeoff roll. Airplane and engine performance deficiencies are detected and annunciated. A novel and important feature of this segment is that it updates the estimated runway rolling friction coefficient. Airplane performance predictions also reflect changes in head wind occurring as the takeoff roll progresses. The system provides a head-down display and a head-up display. The head-up display is projected onto a partially reflective transparent surface through which the pilot views the runway. By comparing the present performance of the airplane with a predicted nominal performance based upon given conditions, performance deficiencies are detected by the system.

The effect of windshear during takeoff roll on aircraft stopping distance

NASA Technical Reports Server (NTRS)

Zweifel, Terry

1990-01-01

A simulation of a Boeing 727 aircraft during acceleration on the runway is used to determine the effect of windshear on stopping distance. Windshears of various magnitudes, durations, and onset times are simulated to assess the aircraft performance during an aborted takeoff on five different runway surfaces. A windshear detection system, active during the takeoff roll and similar to the Honeywell Windshear Detection System is simulated to provide a discrete system to activate aircraft braking upon shear detection. The results of the simulation indicate that several factors effect the distance required to stop the aircraft. Notable among these are gross weight, takeoff flap position, runway characteristics, and pilot reaction time. Of the windshear parameters of duration, onset and magnitude, magnitude appears to have the most significant effect.

Aviation System Capacity Program Terminal Area Productivity Project: Ground and Airborne Technologies

NASA Technical Reports Server (NTRS)

Giulianetti, Demo J.

2001-01-01

Ground and airborne technologies were developed in the Terminal Area Productivity (TAP) project for increasing throughput at major airports by safely maintaining good-weather operating capacity during bad weather. Methods were demonstrated for accurately predicting vortices to prevent wake-turbulence encounters and to reduce in-trail separation requirements for aircraft approaching the same runway for landing. Technology was demonstrated that safely enabled independent simultaneous approaches in poor weather conditions to parallel runways spaced less than 3,400 ft apart. Guidance, control, and situation-awareness systems were developed to reduce congestion in airport surface operations resulting from the increased throughput, particularly during night and instrument meteorological conditions (IMC). These systems decreased runway occupancy time by safely and smoothly decelerating the aircraft, increasing taxi speed, and safely steering the aircraft off the runway. Simulations were performed in which optimal trajectories were determined by air traffic control (ATC) and communicated to flight crews by means of Center TRACON Automation System/Flight Management System (CTASFMS) automation to reduce flight delays, increase throughput, and ensure flight safety.

SURF IA Conflict Detection and Resolution Algorithm Evaluation

NASA Technical Reports Server (NTRS)

Jones, Denise R.; Chartrand, Ryan C.; Wilson, Sara R.; Commo, Sean A.; Barker, Glover D.

2012-01-01

The Enhanced Traffic Situational Awareness on the Airport Surface with Indications and Alerts (SURF IA) algorithm was evaluated in a fast-time batch simulation study at the National Aeronautics and Space Administration (NASA) Langley Research Center. SURF IA is designed to increase flight crew situation awareness of the runway environment and facilitate an appropriate and timely response to potential conflict situations. The purpose of the study was to evaluate the performance of the SURF IA algorithm under various runway scenarios, multiple levels of conflict detection and resolution (CD&R) system equipage, and various levels of horizontal position accuracy. This paper gives an overview of the SURF IA concept, simulation study, and results. Runway incursions are a serious aviation safety hazard. As such, the FAA is committed to reducing the severity, number, and rate of runway incursions by implementing a combination of guidance, education, outreach, training, technology, infrastructure, and risk identification and mitigation initiatives [1]. Progress has been made in reducing the number of serious incursions - from a high of 67 in Fiscal Year (FY) 2000 to 6 in FY2010. However, the rate of all incursions has risen steadily over recent years - from a rate of 12.3 incursions per million operations in FY2005 to a rate of 18.9 incursions per million operations in FY2010 [1, 2]. The National Transportation Safety Board (NTSB) also considers runway incursions to be a serious aviation safety hazard, listing runway incursion prevention as one of their most wanted transportation safety improvements [3]. The NTSB recommends that immediate warning of probable collisions/incursions be given directly to flight crews in the cockpit [4].

KENNEDY SPACE CENTER, FLA. -- Two control towers are seen at the edge of the KSC Shuttle Landing Facility, the old one in front and the nearly completed new tower in back. The old tower stands only 20 feet above the runway surface, too low to see the launch pads to the east. During nighttime landing operations, those inside the tower have been hindered by the eight-billion candlepower xenon lights that illuminate the runway. The new control tower is built atop an existing mound, rising nearly 100 feet over the midpoint of the runway. The height gives controllers a spectacular 360-degree view of NASA-KSC and northern Brevard County. The new facility will also replace the SLF Operations Building. The operations building is home to the Military Radar Unit that monitors NASA-KSC airspace 24 hours a day, as well as runway light controls, navigational aids, weather and wind speed instrumentation, and gate controls. In the new tower, the computer displays will be fully modernized to Federal Aviation Administration standards with touch-screen technology. Construction on the new facility began in February 2003 and is nearly ready for occupancy. Only some final inspections and approvals remain. A support building and Public Affairs viewing deck, to be used for observing future landing operations, will be added and are already in work.

NASA Image and Video Library

2003-12-17

KENNEDY SPACE CENTER, FLA. -- Two control towers are seen at the edge of the KSC Shuttle Landing Facility, the old one in front and the nearly completed new tower in back. The old tower stands only 20 feet above the runway surface, too low to see the launch pads to the east. During nighttime landing operations, those inside the tower have been hindered by the eight-billion candlepower xenon lights that illuminate the runway. The new control tower is built atop an existing mound, rising nearly 100 feet over the midpoint of the runway. The height gives controllers a spectacular 360-degree view of NASA-KSC and northern Brevard County. The new facility will also replace the SLF Operations Building. The operations building is home to the Military Radar Unit that monitors NASA-KSC airspace 24 hours a day, as well as runway light controls, navigational aids, weather and wind speed instrumentation, and gate controls. In the new tower, the computer displays will be fully modernized to Federal Aviation Administration standards with touch-screen technology. Construction on the new facility began in February 2003 and is nearly ready for occupancy. Only some final inspections and approvals remain. A support building and Public Affairs viewing deck, to be used for observing future landing operations, will be added and are already in work.

14 CFR 151.79 - Runway paving: Second runway; wind conditions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Runway paving: Second runway; wind...: Second runway; wind conditions. (a) All airports. Paving a second runway on the basis of wind conditions... second runway is oriented with the existing paved runway to achieve the maximum wind coverage, with due...

14 CFR 151.79 - Runway paving: Second runway; wind conditions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Runway paving: Second runway; wind...: Second runway; wind conditions. (a) All airports. Paving a second runway on the basis of wind conditions... second runway is oriented with the existing paved runway to achieve the maximum wind coverage, with due...

14 CFR 151.79 - Runway paving: Second runway; wind conditions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Runway paving: Second runway; wind...: Second runway; wind conditions. (a) All airports. Paving a second runway on the basis of wind conditions... second runway is oriented with the existing paved runway to achieve the maximum wind coverage, with due...

14 CFR 151.79 - Runway paving: Second runway; wind conditions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Runway paving: Second runway; wind...: Second runway; wind conditions. (a) All airports. Paving a second runway on the basis of wind conditions... second runway is oriented with the existing paved runway to achieve the maximum wind coverage, with due...

Airplane takeoff and landing performance monitoring system

NASA Technical Reports Server (NTRS)

Middleton, David B. (Inventor); Srivatsan, Raghavachari (Inventor); Person, Lee H., Jr. (Inventor)

1994-01-01

The invention is a real-time takeoff and landing performance monitoring system for an aircraft which provides a pilot with graphic and metric information to assist in decisions related to achieving rotation speed (VR) within the safe zone of a runway, or stopping the aircraft on the runway after landing or take-off abort. The system processes information in two segments: a pretakeoff segment and a real-time segment. One-time inputs of ambient conditions and airplane configuration information are used in the pretakeoff segment to generate scheduled performance data. The real-time segment uses the scheduled performance data, runway length data and transducer measured parameters to monitor the performance of the airplane throughout the takeoff roll. Airplane acceleration and engine-performance anomalies are detected and annunciated. A novel and important feature of this segment is that it updates the estimated runway rolling friction coefficient. Airplane performance predictions also reflect changes in head wind occurring as the takeoff roll progresses. The system provides a head-down display and a head-up display. The head-up display is projected onto a partially reflective transparent surface through which the pilot views the runway. By comparing the present performance of the airplane with a continually predicted nominal performance based upon given conditions, performance deficiencies are detected by the system and conveyed to pilot in form of both elemental information and integrated information.

Airplane takeoff and landing performance monitoring system

NASA Technical Reports Server (NTRS)

Middleton, David B. (Inventor); Srivatsan, Raghavachari (Inventor); Person, Jr., Lee H. (Inventor)

1996-01-01

The invention is a real-time takeoff and landing performance monitoring system for an aircraft which provides a pilot with graphic and metric information to assist in decisions related to achieving rotation speed (V.sub.R) within the safe zone of a runway, or stopping the aircraft on the runway after landing or take-off abort. The system processes information in two segments: a pretakeoff segment and a real-time segment. One-time inputs of ambient conditions and airplane configuration information are used in the pretakeoff segment to generate scheduled performance data. The real-time segment uses the scheduled performance data, runway length data and transducer measured parameters to monitor the performance of the airplane throughout the takeoff roll. Airplane acceleration and engine-performance anomalies are detected and annunciated. A novel and important feature of this segment is that it updates the estimated runway rolling friction coefficient. Airplane performance predictions also reflect changes in head wind occurring as the takeoff roll progresses. The system provides a head-down display and a head-up display. The head-up display is projected onto a partially reflective transparent surface through which the pilot views the runway. By comparing the present performance of the airplane with a continually predicted nominal performance based upon given conditions, performance deficiencies are detected by the system and conveyed to pilot in form of both elemental information and integrated information.

Surface Traffic Management Research

NASA Technical Reports Server (NTRS)

Jung, Yoo Chul

2012-01-01

This presentation discusses an overview of the surface traffic management research conducted by NASA Ames. The concept and human-in-the-loop simulation of the Spot and Runway Departure Advisor (SARDA), an integrated decision support tool for the tower controllers and airline ramp operators, is also discussed.

Index of National Aviation Facilities Experimental Center Technical Reports 1972-1977.

DTIC Science & Technology

1981-05-01

EVALUATION OF DIGITAL ALTIMETER SETTING INDICATORS Robert Frack , Ernest E. Sch’atter and Jack Bernstein Final, August 1975 55 P. (RD-75-81) (AD A013 994...runway would change the surface friction of that runway. The method consisted of jetting water at high velocity to hydraulically remove the rubber from...77-49 Erikson, Robert H. 74-17 Feher, Ray E. 76-53; 77-22 Fisher, Donald A. 74-24; 75-48; 76-15 Fisher, John J. 73-41 Frack , Robert 74-46 Gallagher

76 FR 5510 - Safety Enhancements Part 139, Certification of Airports

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-01

... prevent accidents and incidents in that area. A certificate holder would be required to conduct pavement... Pavement Surface Evaluation Braking performance is critical for all aircraft especially on wet runway surfaces. Under certain conditions, hydroplaning or unacceptable loss of traction (tire/pavement contact...

78 FR 3311 - Safety Enhancements, Certification of Airports

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-16

... the airport non-movement area, and (5) Requiring certificate holders to conduct pavement surface... (SMGCS). Non-Movement Area Safety Training... YES NO. Runway Pavement Surface Evaluation.. YES NO. In... 139 to host scheduled passenger carrying operations of an air carrier operating aircraft designed for...

Terminal area automatic navigation, guidance, and control 1: Automatic rollout, turnoff, and taxis

NASA Technical Reports Server (NTRS)

Pines, S.

1981-01-01

A study developed for the TCV B-737, designed to apply existing navigation aids plus magnetic leader cable signals and develop breaking and reverse thrust guidance laws to provide for rapid automated rollout, turnoff, and taxi to reduce runway occupation time for a wide variety of landing conditions for conventional commercial-type aircraft, is described. Closed loop guidance laws for braking and reverse thrust are derived for rollout, turnoff, and taxi, as functions of the landing speed, the desired taxi speed and the distance to go. Brake limitations for wet runway conditions and reverse thrust limitations are taken into account to provide decision rules to avoid tire skid and to choose an alternate turnoff point, farther down the runway, to accommodate extreme landing conditions.

Modelling runway incursion severity.

PubMed

Wilke, Sabine; Majumdar, Arnab; Ochieng, Washington Y

2015-06-01

Analysis of the causes underlying runway incursions is fundamental for the development of effective mitigation measures. However, there are significant weaknesses in the current methods to model these factors. This paper proposes a structured framework for modelling causal factors and their relationship to severity, which includes a description of the airport surface system architecture, establishment of terminological definitions, the determination and collection of appropriate data, the analysis of occurrences for severity and causes, and the execution of a statistical analysis framework. It is implemented in the context of U.S. airports, enabling the identification of a number of priority interventions, including the need for better investigation and causal factor capture, recommendations for airfield design, operating scenarios and technologies, and better training for human operators in the system. The framework is recommended for the analysis of runway incursions to support safety improvements and the methodology is transferable to other areas of aviation safety risk analysis. Copyright © 2015 Elsevier Ltd. All rights reserved.

Characterizing a Wake-Free Safe Zone for the Simplified Aircraft-Based Paired Approach Concept

NASA Technical Reports Server (NTRS)

Guerreiro, Nelson M.; Neitzke, Kurt W.; Johnson, Sally C.; Stough, H. Paul, III; McKissick, Burnell T.; Syed, Hazari I.

2010-01-01

The Federal Aviation Administration (FAA) has proposed a concept of operations geared towards achieving increased arrival throughput at U.S. Airports, known as the Simplified Aircraft-based Paired Approach (SAPA) concept. In this study, a preliminary characterization of a wake-free safe zone (WFSZ) for the SAPA concept has been performed. The experiment employed Monte-Carlo simulations of varying approach profiles by aircraft pairs to closely-spaced parallel runways. Three different runway lateral spacings were investigated (750 ft, 1000 ft and 1400 ft), along with no stagger and 1500 ft stagger between runway thresholds. The paired aircraft were flown in a leader/trailer configuration with potential wake encounters detected using a wake detection surface translating with the trailing aircraft. The WFSZ is characterized in terms of the smallest observed initial in-trail distance leading to a wake encounter anywhere along the approach path of the aircraft. The results suggest that the WFSZ can be characterized in terms of two primary altitude regions, in ground-effect (IGE) and out of ground-effect (OGE), with the IGE region being the limiting case with a significantly smaller WFSZ. Runway stagger was observed to only modestly reduce the WFSZ size, predominantly in the OGE region.

Human factors considerations for the integration of traffic information and alerts on an airport surface map

DOT National Transportation Integrated Search

2010-12-01

The purpose of this document is to provide human factors considerations in the integration of traffic information and indications and alerts for runway status on an airport surface moving map. The US DOT Volpe Center, in support of the Federal Aviati...

An Overview of the Annual NASA Tire/Runway Friction Workshop and Lessons Learned

NASA Technical Reports Server (NTRS)

Yager, Thomas J.

2005-01-01

This paper summarizes the organization efforts, objectives, scope, agenda, test procedures and results from eleven years of conducting the NASA Tire/Runway Friction Workshop. The paper will also summarize the lessons learned between 1994 and 2004. A description of the various friction, texture and roughness equipment used during these workshops at NASA Wallops Flight Facility on the eastern shore of Virginia will be provided together with the range of test surfaces available for evaluation. The need for friction measuring equipment calibration centers is discussed and plans for future workshops are identified.

System-Oriented Runway Management Concept of Operations

NASA Technical Reports Server (NTRS)

Lohr, Gary W.; Atkins, Stephen

2015-01-01

This document describes a concept for runway management that maximizes the overall efficiency of arrival and departure operations at an airport or group of airports. Specifically, by planning airport runway configurations/usage, it focuses on the efficiency with which arrival flights reach their parking gates from their arrival fixes and departure flights exit the terminal airspace from their parking gates. In the future, the concept could be expanded to include the management of other limited airport resources. While most easily described in the context of a single airport, the concept applies equally well to a group of airports that comprise a metroplex (i.e., airports in close proximity that share resources such that operations at the airports are at least partially dependent) by including the coordination of runway usage decisions between the airports. In fact, the potential benefit of the concept is expected to be larger in future metroplex environments due to the increasing need to coordinate the operations at proximate airports to more efficiently share limited airspace resources. This concept, called System-Oriented Runway Management (SORM), is further broken down into a set of airport traffic management functions that share the principle that operational performance must be measured over the complete surface and airborne trajectories of the airport's arrivals and departures. The "system-oriented" term derives from the belief that the traffic management objective must consider the efficiency of operations over a wide range of aircraft movements and National Airspace System (NAS) dynamics. The SORM concept is comprised of three primary elements: strategic airport capacity planning, airport configuration management, and combined arrival/departure runway planning. Some aspects of the SORM concept, such as using airport configuration management1 as a mechanism for improving aircraft efficiency, are novel. Other elements (e.g., runway scheduling, which is a part of combined arrival/departure runway scheduling) have been well studied, but are included in the concept for completeness and to allow the concept to define the necessary relationship among the elements. The goal of this document is to describe the overall SORM concept and how it would apply both within the NAS and potential future Next Generation Air Traffic System (NextGen) environments, including research conducted to date. Note that the concept is based on the belief that runways are the primary constraint and the decision point for controlling efficiency, but the efficiency of runway management must be measured over a wide range of space and time. Implementation of the SORM concept is envisioned through a collection of complementary, necessary capabilities collectively focused on ensuring efficient arrival and departure traffic management, where that efficiency is measured not only in terms of runway efficiency but in terms of the overall trajectories between parking gates and transition fixes. For the more original elements of the concept-airport configuration management-this document proposes specific air traffic management (ATM) decision-support automation for realizing the concept.

SARDA - Technologies for NextGen

NASA Image and Video Library

2015-04-22

The Spot and Runway Departure Advisor, or SARDA, is NASA's contribution to improving the efficiency of airport surface operations. SARDA is comprised of software-based decision support tools for controllers in the FAA tower and in the airline ramp towers. It uses intelligent schedulers to provide surface management capabilities, including departure metering and advisories for individual aircraft movement at various locations on the airport surface.

Friction characteristics of three 30 by 11.5-14.5, type 8, aircraft tires with various tread groove patterns and rubber compounds

NASA Technical Reports Server (NTRS)

Yager, T. J.; Mccarty, J. L.

1977-01-01

A test program was conducted to evaluate friction performance and wear characteristics on wet runways of three 30 x 11.5-14.5, type, aircraft tires having two different tread patterns and natural rubber contents. All test tires had the standard three circumferential groove tread, but two had molded transverse grooves which extended from shoulder to shoulder. The tread rubber content of the two tires with transverse grooves differed in that one had a 100 percent natural rubber tread and the other had a rubber tread composition that was 30 percent synthetic and 70 percent natural. The third test tire had the conventional 100 percent natural rubber tread. Results indicate that the differences in tire tread design and rubber composition do not significantly affect braking and cornering friction capability on wet or dry surfaces. Braking performance of the tires decreases with increased speed, with increased yaw angle and, at higher speeds, with increased wetness of the surface.

14 CFR 23.235 - Operation on unpaved surfaces.

Code of Federal Regulations, 2011 CFR

2011-01-01

... structure of the airplane when the airplane is taxied on the roughest ground that may reasonably be expected in normal operation and when takeoffs and landings are performed on unpaved runways having the...

14 CFR 23.235 - Operation on unpaved surfaces.

Code of Federal Regulations, 2010 CFR

2010-01-01

... structure of the airplane when the airplane is taxied on the roughest ground that may reasonably be expected in normal operation and when takeoffs and landings are performed on unpaved runways having the...

Ultrasonic simulation of MSBLS multipath fading for orbiter landing configuration

NASA Technical Reports Server (NTRS)

Hayre, H. S.

1978-01-01

The on-shuttle antenna pattern of the MSBLS receiver, and the azimuth and elevation beamwidths were simulated by their corresponding ultrasonic transducer beams. The scanning rate for the azimuth and elevation beams was 1.75 degrees/second. The results were adjusted for full-scale maximum sinusoidal scan rates of 691 and 377 deg/sec for AZ and EL respectively. The rain drops were simulated by air bubbles, with a similar size distribution, in water. The rain volume was created along a part of the propagation path, and not on the runway, because it was found difficult to avoid an accumulation of bubbles on the runway surface and surroundings simulated by the model surface. Multipath fading from the ground, and its possible degrading effect on the orbiter received beam shape and the associated landing guidance parameters is discussed.

The NASA landing gear test airplane

NASA Technical Reports Server (NTRS)

Carter, John F.; Nagy, Christopher J.

1995-01-01

A tire and landing gear test facility has been developed and incorporated into a Convair 990 aircraft. The system can simulate tire vertical load profiles to 250,000 lb, sideslip angles to 15 degrees, and wheel braking on actual runways. Onboard computers control the preprogrammed test profiles through a feedback loop and also record three axis loads, tire slip angle, and tire condition. The aircraft to date has provided tire force and wear data for the Shuttle Orbiter tire on three different runways and at east and west coast landing sites. This report discusses the role of this facility in complementing existing ground tire and landing gear test facilities, and how this facility can simultaneously simulate the vertical load, tire slip, velocity, and surface for an entire aircraft landing. A description is given of the aircraft as well as the test system. An example of a typical test sequence is presented. Data collection and reduction from this facility are discussed, as well as accuracies of calculated parameters. Validation of the facility through ground and flight tests is presented. Tests to date have shown that this facility can operate at remote sites and gather complete data sets of load, slip, and velocity on actual runway surfaces. The ground and flight tests have led to a successful validation of this test facility.

Climate change and the impact of extreme temperatures on aviation

NASA Astrophysics Data System (ADS)

Coffel, E.; Horton, R.

2014-12-01

Weather is the most significant factor affecting aircraft operations, accounting for 70-80% of passenger delays and costing airlines hundreds of millions of dollars per year in lost revenue. Temperature and airport elevation significantly influence the maximum allowable takeoff weight of an aircraft by changing the surface air density and thus the lift produced at a given speed. For a given runway length, airport elevation, and aircraft type there is a temperature threshold above which the airplane cannot take off at its maximum weight and thus must be weight restricted. The number of summer days necessitating weight restriction has increased since 1980 along with the observed increase in surface temperature. Climate change is projected to increase mean temperatures at all airports and significantly increase the frequency and severity of extreme heat events at some. These changes will negatively affect aircraft performance, leading to increased weight restrictions especially at airports with short runways and little room to expand. For a Boeing 737-800 aircraft, we find that the number of weight restriction days between May and September will increase by 50-100% at four major airports in the United States by 2050-2070 under the RCP8.5 high emissions scenario. These performance reductions may have a significant economic effect on the airline industry, leading to lower profits and higher passenger fares. Increased weight restrictions have previously been identified as potential impacts of climate change, but this study is the first to quantify the effect of higher temperatures on commercial aviation.

Vertical and horizontal distributions of microbial abundances and enzymatic activities in propylene-glycol-affected soils.

PubMed

Biró, Borbála; Toscano, Giuseppe; Horváth, Nikoletta; Matics, Heléna; Domonkos, Mónika; Scotti, Riccardo; Rao, Maria A; Wejden, Bente; French, Helen K

2014-01-01

The natural microbial activity in the unsaturated soil is vital for protecting groundwater in areas where high loads of biodegradable contaminants are supplied to the surface, which usually is the case for airports using aircraft de-icing fluids (ADF) in the cold season. Horizontal and vertical distributions of microbial abundance were assessed along the western runway of Oslo Airport (Gardermoen, Norway) to monitor the effect of ADF dispersion with special reference to the component with the highest chemical oxygen demand (COD), propylene glycol (PG). Microbial abundance was evaluated by several biondicators: colony-forming units (CFU) of some physiological groups (aerobic and anaerobic heterotrophs and microscopic fungi), most probable numbers (MPN) of PG degraders, selected catabolic enzymatic activities (fluorescein diacetate (FDA) hydrolase, dehydrogenase, and β-glucosidase). High correlations were found between the enzymatic activities and microbial counts in vertical soil profiles. All microbial abundance indicators showed a steep drop in the first meter of soil depth. The vertical distribution of microbial abundance can be correlated by a decreasing exponential function of depth. The horizontal trend of microbial abundance (evaluated as total aerobic CFU, MPN of PG-degraders, and FDA hydrolase activity) assessed in the surface soil at an increasing distance from the runway is correlated negatively with the PG and COD loads, suggesting the relevance of other chemicals in the modulation of microbial growth. The possible role of potassium formate, component of runway de-icers, has been tested in the laboratory by using mixed cultures of Pseudomonas spp., obtained by enrichment with a selective PG medium from soil samples taken at the most contaminated area near the runway. The inhibitory effect of formate on the growth of PG degraders is proven by the reduction of biomass yield on PG in the presence of formate.

Positioning System Accuracy Assessment for the Runway Incursion Prevention System Flight Test at the Dallas/Ft. Worth International Airport

NASA Technical Reports Server (NTRS)

Quach, Cuong C.

2004-01-01

NASA/Langley Research Center collaborated with the Federal Aviation Administration (FAA) to test a Runway Incursion Prevention System (RIPS) at the Dallas Fort Worth International Airport (DFW) in October 2000. The RIPS combines airborne and ground sensor data with various cockpit displays to improve pilots' awareness of traffic conditions on the airport surface. The systems tested at DFW involved surface radar and data systems that gather and send surface traffic information to a research aircraft outfitted with the RIPS software, cockpit displays, and data link transceivers. The data sent to the airborne systems contained identification and GPS location of traffic. This information was compared with the own-ship location from airborne GPS receivers to generate incursion alerts. A total of 93 test tracks were flown while operating RIPS. This report compares the accuracy of the airborne GPS systems that gave the own-ship position of the research aircraft for the 93 test tracks.

14 CFR 77.19 - Civil airport imaginary surfaces.

Code of Federal Regulations, 2012 CFR

2012-01-01

..., having visibility minimums greater that three-fourths of a statute mile; (v) 4,000 feet for that end of a... visibility minimums as low as three-fourths statute mile; and (vi) 16,000 feet for precision instrument... existing or planned for that runway end. (a) Horizontal surface. A horizontal plane 150 feet above the...

14 CFR 77.19 - Civil airport imaginary surfaces.

Code of Federal Regulations, 2013 CFR

2013-01-01

..., having visibility minimums greater that three-fourths of a statute mile; (v) 4,000 feet for that end of a... visibility minimums as low as three-fourths statute mile; and (vi) 16,000 feet for precision instrument... existing or planned for that runway end. (a) Horizontal surface. A horizontal plane 150 feet above the...

14 CFR 77.19 - Civil airport imaginary surfaces.

Code of Federal Regulations, 2014 CFR

2014-01-01

..., having visibility minimums greater that three-fourths of a statute mile; (v) 4,000 feet for that end of a... visibility minimums as low as three-fourths statute mile; and (vi) 16,000 feet for precision instrument... existing or planned for that runway end. (a) Horizontal surface. A horizontal plane 150 feet above the...

Low-Cost ASDE Evaluation Report: Raytheon Marine (Phase I) Radar at MKE (ARPA M345O/18CPX-19), Volume I.

DOT National Transportation Integrated Search

1996-07-31

The FAA has identified the Airport Surface Detection Equipment as a radar system that aids air traffic controllers in low visibility conditions to detect surface radar targets and sequence aircraft movement on active runways. Though 35 major U.S. air...

Baseline monitoring using aircraft laser ranging. [spaceborne laser simulation and aircraft laser tracking

NASA Technical Reports Server (NTRS)

Krabill, W. B.; Hoge, F. E.; Martin, C. F.

1982-01-01

The use of aircraft laser ranging for the determination of baselines between ground based retroreflectors was investigated via simulations and with tests at Wallops Flight Center using the Airborne Oceanographic Lidar (AOL) on the Wallops C-54 aircraft ranging to a reflector array deployed around one of the Wallops runways. The aircraft altitude and reflector spacing were chosen on the basis of scaled down modeling of spacecraft tracking from 1000 km of reflectors separated by some 52 km, or of high altitude (10 km) aircraft tracking of reflectors separated by some 500 m. Aircraft altitudes flown for different passes across the runway reflector array varied from 800 m to 1350 m, with 32 reflectors deployed over an approximtely 300 m x 500 m ground pattern. The AOL transmitted 400 pulses/sec with a scan rate of 5/sec in a near circular pattern, so that the majority of the pulses were reflected by the runway surface or its environs rather than by retroreflectors. The return pulse characteristics clearly showed the high reflectivity of portions of the runway, with several returns indistinguishable in amplitude from reflector returns. For each pass across the reflector field, typically six to ten reflector hits were identified, consistent with that predicted by simulations and the observed transmitted elliptical pulse size.

Runway Exit Designs for Capacity Improvement Demonstrations. Phase 1: Algorithm Development

NASA Technical Reports Server (NTRS)

Trani, A. A.; Hobeika, A. G.; Sherali, H.; Kim, B. J.; Sadam, C. K.

1990-01-01

A description and results are presented of a study to locate and design rapid runway exits under realistic airport conditions. The study developed a PC-based computer simulation-optimization program called REDIM (runway exit design interactive model) to help future airport designers and planners to locate optimal exits under various airport conditions. The model addresses three sets of problems typically arising during runway exit design evaluations. These are the evaluations of existing runway configurations, addition of new rapid runway turnoffs, and the design of new runway facilities. The model is highly interactive and allows a quick estimation of the expected value of runway occupancy time. Aircraft populations and airport environmental conditions are among the multiple inputs to the model to execute a viable runway location and geometric design solution. The results presented suggest that possible reductions on runway occupancy time (ROT) can be achieved with the use of optimally tailored rapid runway designs for a given aircraft population. Reductions of up to 9 to 6 seconds are possible with the implementation of 30 m/sec variable geometry exits.

Factors influencing aircraft ground handling performance

NASA Technical Reports Server (NTRS)

Yager, T. J.

1983-01-01

Problems associated with aircraft ground handling operations on wet runways are discussed and major factors which influence tire/runway braking and cornering traction capability are identified including runway characteristics, tire hydroplaning, brake system anomalies, and pilot inputs. Research results from tests with instrumented ground vehicles and aircraft, and aircraft wet runway accident investigation are summarized to indicate the effects of different aircraft, tire, and runway parameters. Several promising means are described for improving tire/runway water drainage capability, brake system efficiency, and pilot training to help optimize aircraft traction performance on wet runways.

Models for estimating runway landing capacity with Microwave Landing System (MLS)

NASA Technical Reports Server (NTRS)

Tosic, V.; Horonjeff, R.

1975-01-01

A model is developed which is capable of computing the ultimate landing runway capacity, under ILS and MLS conditions, when aircraft population characteristics and air traffic control separation rules are given. This model can be applied in situations when only a horizontal separation between aircraft approaching a runway is allowed, as well as when both vertical and horizontal separations are possible. It is assumed that the system is free of errors, that is that aircraft arrive at specified points along the prescribed flight path precisely when the controllers intend for them to arrive at these points. Although in the real world there is no such thing as an error-free system, the assumption is adequate for a qualitative comparison of MLS with ILS. Results suggest that an increase in runway landing capacity, caused by introducing the MLS multiple approach paths, is to be expected only when an aircraft population consists of aircraft with significantly differing approach speeds and particularly in situations when vertical separation can be applied. Vertical separation can only be applied if one of the types of aircraft in the mix has a very steep descent angle.

Evaluation of ILS Localizer Signal Specification During Ground Rollout.

DOT National Transportation Integrated Search

1973-08-01

The International Civil Aviation Organization (ICAO) has developed a specification for localizer information on the runway surface appropriate for rollout guidance during Category III B operations. The suitability of this specification was evaluated ...

14 CFR 23.1091 - Air induction system.

Code of Federal Regulations, 2013 CFR

2013-01-01

... indicate to the flight crew when it is not closed. (c) For turbine engine powered airplanes— (1) There must... designed to prevent water or slush on the runway, taxiway, or other airport operating surfaces from being...

14 CFR 23.1091 - Air induction system.

Code of Federal Regulations, 2012 CFR

2012-01-01

... indicate to the flight crew when it is not closed. (c) For turbine engine powered airplanes— (1) There must... designed to prevent water or slush on the runway, taxiway, or other airport operating surfaces from being...

14 CFR 23.1091 - Air induction system.

Code of Federal Regulations, 2014 CFR

2014-01-01

... indicate to the flight crew when it is not closed. (c) For turbine engine powered airplanes— (1) There must... designed to prevent water or slush on the runway, taxiway, or other airport operating surfaces from being...

14 CFR 23.1091 - Air induction system.

Code of Federal Regulations, 2011 CFR

2011-01-01

... indicate to the flight crew when it is not closed. (c) For turbine engine powered airplanes— (1) There must... designed to prevent water or slush on the runway, taxiway, or other airport operating surfaces from being...

Aircraft and runway deicers at General Mitchell International Airport, Milwaukee, Wisconsin, USA. 2. Toxicity of aircraft and runway deicers.

PubMed

Corsi, S R; Hall, D W; Geis, S W

2001-07-01

Streams receiving runoff from General Mitchell International Airport (GMIA), Milwaukee, Wisconsin, USA, were studied to assess toxic impacts of aircraft and runway deicers. Elevated levels of constituents related to deicing (propylene glycol, ethylene glycol, and ammonia) were observed in stream samples. The LC50s of type I deicer for Ceriodaphnia dubia, Pimephelas promelas, Hyalela azteca, and Chironimus tentans and the EC50 for Microtox were less than 5,000 mg/L of propylene glycol. Concentrations up to 39,000 mg/L were observed at airport outfall sites in samples collected during deicing events. The IC25s of type I deicer for C. dubia and P. promelas were less than 1,500 mg/L of propylene glycol. Concentrations up to 960 mg/L were observed in low-flow samples at an airport outfall site. Measured toxicity of stream water was greatest during winter storms when deicers were applied. Chronic toxicity was observed at airport outfall samples from low-flow periods in the winter and the summer, with the greater toxic impacts from the winter sample. All forms of toxicity in stream-water samples decreased as downstream flows increased.

Aircraft and runway deicers at General Mitchell International Airport, Milwaukee, Wisconsin, USA. 2. Toxicity of aircraft and runway deicer

USGS Publications Warehouse

Corsi, Steven; Hall, David W.; Geis, Steven W.

2001-01-01

Streams receiving runoff from General Mitchell International Airport (GMIA), Milwaukee, Wisconsin, USA, were studied to assess toxic impacts of aircraft and runway deicers. Elevated levels of constituents related to deicing (propylene glycol, ethylene glycol, and ammonia) were observed in stream samples. The LC50s of type I deicer for Ceriodaphnia dubia, Pimephelas promelas, Hyalela azteca, and Chironimus tentans and the EC50 for Microtox® were less than 5,000 mg/L of propylene glycol. Concentrations up to 39,000 mg/L were observed at airport outfall sites in samples collected during deicing events. The IC25s of type I deicer for C. dubia and P. promelas were less than 1,500 mg/L of propylene glycol. Concentrations up to 960 mg/L were observed in low-flow samples at an airport outfall site. Measured toxicity of stream water was greatest during winter storms when deicers were applied. Chronic toxicity was observed at airport outfall samples from low-flow periods in the winter and the summer, with the greater toxic impacts from the winter sample. All forms of toxicity in stream-water samples decreased as downstream flows increased.

Airport Characterization for the Adaptation of Surface Congestion Management Approaches

DTIC Science & Technology

2013-02-01

Surface Congestion Management Program at New York JFK airport [6,7], the human-in-the-loop simulations of the Spot and Runway Departure Advisor...a surface congestion management technique at New York JFK airport ,” AIAA Aviation Technology, Integration and Operations (ATIO) Conference...Virginia Beach, VA, September 2011. [7] S. Stroiney, H. Khadilkar and H. Balakrishnan, “Ground Management Program at JFK Airport : Implementation and

Flight simulator with spaced visuals

NASA Technical Reports Server (NTRS)

Gilson, Richard D. (Inventor); Thurston, Marlin O. (Inventor); Olson, Karl W. (Inventor); Ventola, Ronald W. (Inventor)

1980-01-01

A flight simulator arrangement wherein a conventional, movable base flight trainer is combined with a visual cue display surface spaced a predetermined distance from an eye position within the trainer. Thus, three degrees of motive freedom (roll, pitch and crab) are provided for a visual proprioceptive, and vestibular cue system by the trainer while the remaining geometric visual cue image alterations are developed by a video system. A geometric approach to computing runway image eliminates a need to electronically compute trigonometric functions, while utilization of a line generator and designated vanishing point at the video system raster permits facile development of the images of the longitudinal edges of the runway.

75 FR 13337 - Notice of Passenger Facility Charge (PFC) Approvals and Disapprovals

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-19

....00 PFC Level: North terminal complex conceptual design. Cargo service road. Decision Date: December 1... and II). Aircraft rescue and firefighting building (design). Runway 24 runway safety area improvements (design). Runway 24 runway safety area improvements (grading/drainage). Runway 6 localizer (design...

Surface Movement Incidents Reported to the NASA Aviation Safety Reporting System

NASA Technical Reports Server (NTRS)

Connell, Linda J.; Hubener, Simone

1997-01-01

Increasing numbers of aircraft are operating on the surface of airports throughout the world. Airport operations are forecast to grow by more that 50%, by the year 2005. Airport surface movement traffic would therefore be expected to become increasingly congested. Safety of these surface operations will become a focus as airport capacity planning efforts proceed toward the future. Several past events highlight the prevailing risks experienced while moving aircraft during ground operations on runways, taxiways, and other areas at terminal, gates, and ramps. The 1994 St. Louis accident between a taxiing Cessna crossing an active runway and colliding with a landing MD-80 emphasizes the importance of a fail-safe system for airport operations. The following study explores reports of incidents occurring on an airport surface that did not escalate to an accident event. The Aviation Safety Reporting System has collected data on surface movement incidents since 1976. This study sampled the reporting data from June, 1993 through June, 1994. The coding of the data was accomplished in several categories. The categories include location of airport, phase of ground operation, weather /lighting conditions, ground conflicts, flight crew characteristics, human factor considerations, and airport environment. These comparisons and distributions of variables contributing to surface movement incidents can be invaluable to future airport planning, accident prevention efforts, and system-wide improvements.

14 CFR 151.80 - Runway paving: Additional runway; other conditions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Runway paving: Additional runway; other conditions. 151.80 Section 151.80 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AIRPORTS FEDERAL AID TO AIRPORTS Project Programming Standards § 151.80 Runway paving...

14 CFR 151.80 - Runway paving: Additional runway; other conditions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Runway paving: Additional runway; other conditions. 151.80 Section 151.80 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AIRPORTS FEDERAL AID TO AIRPORTS Project Programming Standards § 151.80 Runway paving...

14 CFR 151.80 - Runway paving: Additional runway; other conditions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Runway paving: Additional runway; other conditions. 151.80 Section 151.80 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AIRPORTS FEDERAL AID TO AIRPORTS Project Programming Standards § 151.80 Runway paving...

14 CFR 151.79 - Runway paving: Second runway; wind conditions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Runway paving: Second runway; wind conditions. 151.79 Section 151.79 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AIRPORTS FEDERAL AID TO AIRPORTS Project Programming Standards § 151.79 Runway paving...

14 CFR 151.80 - Runway paving: Additional runway; other conditions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Runway paving: Additional runway; other conditions. 151.80 Section 151.80 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AIRPORTS FEDERAL AID TO AIRPORTS Project Programming Standards § 151.80 Runway paving...

14 CFR 151.80 - Runway paving: Additional runway; other conditions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Runway paving: Additional runway; other conditions. 151.80 Section 151.80 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AIRPORTS FEDERAL AID TO AIRPORTS Project Programming Standards § 151.80 Runway paving...

Review of factors affecting aircraft wet runway performance

NASA Technical Reports Server (NTRS)

Yager, T. J.

1983-01-01

Problems associated with aircraft operations on wet runways are discussed and major factors which influence tire/runway braking and cornering traction capability are identified including runway characteristics, tire hydroplaning, brake system anomalies, and pilot inputs. Research results from investigations conducted at the Langley Aircraft Landing Loads and Traction Facility and from tests with instrumented ground vehicles and aircraft are summarized to indicate the effects of different aircraft, tire, and runway parameters. Several promising means are described for improving tire/runway water drainage capability, brake system efficiency, and pilot training to help optimize aircraft traction performance on wet runways.

Runway Operations Planning: A Two-Stage Heuristic Algorithm

NASA Technical Reports Server (NTRS)

Anagnostakis, Ioannis; Clarke, John-Paul

2003-01-01

The airport runway is a scarce resource that must be shared by different runway operations (arrivals, departures and runway crossings). Given the possible sequences of runway events, careful Runway Operations Planning (ROP) is required if runway utilization is to be maximized. From the perspective of departures, ROP solutions are aircraft departure schedules developed by optimally allocating runway time for departures given the time required for arrivals and crossings. In addition to the obvious objective of maximizing throughput, other objectives, such as guaranteeing fairness and minimizing environmental impact, can also be incorporated into the ROP solution subject to constraints introduced by Air Traffic Control (ATC) procedures. This paper introduces a two stage heuristic algorithm for solving the Runway Operations Planning (ROP) problem. In the first stage, sequences of departure class slots and runway crossings slots are generated and ranked based on departure runway throughput under stochastic conditions. In the second stage, the departure class slots are populated with specific flights from the pool of available aircraft, by solving an integer program with a Branch & Bound algorithm implementation. Preliminary results from this implementation of the two-stage algorithm on real-world traffic data are presented.

Friction and wear behavior of aluminum and composite I-beam stiffened airplane skins

NASA Technical Reports Server (NTRS)

Jackson, K. E.

1985-01-01

Friction and wear behavior was determined for I-beam stiffened skins constructed of aluminum, graphite-epoxy composite, and glass hybrid composite under abrasive loading conditions typical of those occurring on the underside of a transport airplane during an emergency belly landing. A test apparatus was developed to abrade the test specimens on actual runway surface under a range of pressures (2-5 psi) and velocities (16-50 mph). These parameters were chosen to fall within the range of conditions typical of an airframe sliding on a runway surface. The effects of the test variables on the wear rate and the coefficient of friction are discussed and comparisons are made between the composite materials and aluminum. In addition, the test apparatus was equipped to monitor the temperature variations on the backside of the skins during abrasion and these results are presented.

Recent Progress Towards Predicting Aircraft Ground Handling Performance

NASA Technical Reports Server (NTRS)

Yager, T. J.; White, E. J.

1981-01-01

The significant progress which has been achieved in development of aircraft ground handling simulation capability is reviewed and additional improvements in software modeling identified. The problem associated with providing necessary simulator input data for adequate modeling of aircraft tire/runway friction behavior is discussed and efforts to improve this complex model, and hence simulator fidelity, are described. Aircraft braking performance data obtained on several wet runway surfaces is compared to ground vehicle friction measurements and, by use of empirically derived methods, good agreement between actual and estimated aircraft braking friction from ground vehilce data is shown. The performance of a relatively new friction measuring device, the friction tester, showed great promise in providing data applicable to aircraft friction performance. Additional research efforts to improve methods of predicting tire friction performance are discussed including use of an instrumented tire test vehicle to expand the tire friction data bank and a study of surface texture measurement techniques.

14 CFR 77.25 - Civil airport imaginary surfaces.

Code of Federal Regulations, 2011 CFR

2011-01-01

... relation to the airport and to each runway. The size of each such imaginary surface is based on the... feet above the established airport elevation, the perimeter of which is constructed by swinging arcs of... connecting the adjacent arcs by lines tangent to those arcs. The radius of each arc is: (1) 5,000 feet for...

Aircraft Jet Engine Exhaust Blast Effects on Par-56 Runway Threshold Lamp Fixtures

DTIC Science & Technology

1989-06-01

Engine Type(s): SPEY 511-14 British Aerospace, BAe-125-700/ -700 Engine Type(s): Garret TFE731 -3 British Aerospace, Concorde Engine Type(s): Not Given... TFE731 -3B Falcon Jet, Falcon 50 Engine Type(s): Garrett TFE-731-3C (See data for Citation) Gates Learjet, Models 23/24, 35/36, 35A/36A, 55/55B Engine Type

Current Practices in Runway Configuration Management (RCM) and Arrival/Departure Runway Balancing (ADRB)

NASA Technical Reports Server (NTRS)

Lohr, Gary W.; Williams, Daniel M.

2008-01-01

Significant air traffic increases are anticipated for the future of the National Airspace System (NAS). To cope with future traffic increases, fundamental changes are required in many aspects of the air traffic management process including the planning and use of NAS resources. Two critical elements of this process are the selection of airport runway configurations, and the effective management of active runways. Two specific research areas in NASA's Airspace Systems Program (ASP) have been identified to address efficient runway management: Runway Configuration Management (RCM) and Arrival/Departure Runway Balancing (ADRB). This report documents efforts in assessing past as well as current work in these two areas.

Runway Safety Monitor Algorithm for Single and Crossing Runway Incursion Detection and Alerting

NASA Technical Reports Server (NTRS)

Green, David F., Jr.

2006-01-01

The Runway Safety Monitor (RSM) is an aircraft based algorithm for runway incursion detection and alerting that was developed in support of NASA's Runway Incursion Prevention System (RIPS) research conducted under the NASA Aviation Safety and Security Program's Synthetic Vision System project. The RSM algorithm provides warnings of runway incursions in sufficient time for pilots to take evasive action and avoid accidents during landings, takeoffs or when taxiing on the runway. The report documents the RSM software and describes in detail how RSM performs runway incursion detection and alerting functions for NASA RIPS. The report also describes the RIPS flight tests conducted at the Reno/Tahoe International Airport (RNO) and the Wallops Flight Facility (WAL) during July and August of 2004, and the RSM performance results and lessons learned from those flight tests.

LSRA STS Tire Test - on rim

NASA Technical Reports Server (NTRS)

1995-01-01

From 1993 to 1995, in conjunction with other NASA centers, NASA Dryden Flight Research Center, Edwards, California, used a Convair CV-990 airplane as a Landing Systems Research Aircraft (LSRA) to perform Space Shuttle tire tests. The results provided the Space Shuttle Program with data to support its flight rules and enabled it to resurface a grooved runway at Kennedy Space Center that had added unnecessary wear to the Space Shuttle tires. Tests were done using a unique fixture mounted in the center of the CV-990 fuselage, between the main landing gear. Landing gear systems from other aircraft could be attached to the test fixture, which lowered them to the runway surface during actual landings. The LSRA had the ability to reproduce the loads and speeds of the other aircraft, as well as simulate crosswind landing conditions in a safe, controlled environment. The video clip shows a landing on the concrete runway at Edwards, California on August 11, 1995, which concluded the Space Shuttle gear research program. As the Space Shuttle tire was lowered onto the surface, it was destroyed almost instantly. The rim scraped on the concrete, and stopped rolling as it became flat. It heated up and left a flaming trail of hot rubber and aluminum alloy particles. Notice how the fire quickly went out as the test gear was raised, indicating a safer condition than prevailed in a lakebed landing.

Aerial view of Runway 33 at SLF

NASA Technical Reports Server (NTRS)

2000-01-01

This aerial view shows the approach on Runway 33 at the KSC Shuttle Landing Facility. The runway is 15,000 feet long, with 1,000-foot paved overruns at each end; 300 feet wide (about length of football field), with 50-foot asphalt shoulders each side; 16 inches thick in the center, and 15 inches thick on sides. It has a slope of 24 inches from the center line to the edge for drainage. The single landing strip is considered two runways, depending on approach -- Runway 15 from northwest, Runway 33 from southeast.

Optimizing integrated airport surface and terminal airspace operations under uncertainty

NASA Astrophysics Data System (ADS)

Bosson, Christabelle S.

In airports and surrounding terminal airspaces, the integration of surface, arrival and departure scheduling and routing have the potential to improve the operations efficiency. Moreover, because both the airport surface and the terminal airspace are often altered by random perturbations, the consideration of uncertainty in flight schedules is crucial to improve the design of robust flight schedules. Previous research mainly focused on independently solving arrival scheduling problems, departure scheduling problems and surface management scheduling problems and most of the developed models are deterministic. This dissertation presents an alternate method to model the integrated operations by using a machine job-shop scheduling formulation. A multistage stochastic programming approach is chosen to formulate the problem in the presence of uncertainty and candidate solutions are obtained by solving sample average approximation problems with finite sample size. The developed mixed-integer-linear-programming algorithm-based scheduler is capable of computing optimal aircraft schedules and routings that reflect the integration of air and ground operations. The assembled methodology is applied to a Los Angeles case study. To show the benefits of integrated operations over First-Come-First-Served, a preliminary proof-of-concept is conducted for a set of fourteen aircraft evolving under deterministic conditions in a model of the Los Angeles International Airport surface and surrounding terminal areas. Using historical data, a representative 30-minute traffic schedule and aircraft mix scenario is constructed. The results of the Los Angeles application show that the integration of air and ground operations and the use of a time-based separation strategy enable both significant surface and air time savings. The solution computed by the optimization provides a more efficient routing and scheduling than the First-Come-First-Served solution. Additionally, a data driven analysis is performed for the Los Angeles environment and probabilistic distributions of pertinent uncertainty sources are obtained. A sensitivity analysis is then carried out to assess the methodology performance and find optimal sampling parameters. Finally, simulations of increasing traffic density in the presence of uncertainty are conducted first for integrated arrivals and departures, then for integrated surface and air operations. To compare the optimization results and show the benefits of integrated operations, two aircraft separation methods are implemented that offer different routing options. The simulations of integrated air operations and the simulations of integrated air and surface operations demonstrate that significant traveling time savings, both total and individual surface and air times, can be obtained when more direct routes are allowed to be traveled even in the presence of uncertainty. The resulting routings induce however extra take off delay for departing flights. As a consequence, some flights cannot meet their initial assigned runway slot which engenders runway position shifting when comparing resulting runway sequences computed under both deterministic and stochastic conditions. The optimization is able to compute an optimal runway schedule that represents an optimal balance between total schedule delays and total travel times.

Ground Taxi Navigation Problems and Training Solutions

NASA Technical Reports Server (NTRS)

Quinn, Cheryl; Walter, Kim E.; Rosekind, Mark (Technical Monitor)

1997-01-01

Adverse weather conditions can put considerable strain on the National Airspace System. Even small decreases in visibility on the airport surface can create delays, hinder safe movement and lead to errors. Studies of Aviation Safety Reporting System (ASRS) surface movement incidents support the need for technologies and procedures to improve ground operations in low-visibility conditions. This study examined 139 ASRS reports of low-visibility surface movement incidents at 10 major U.S. airports. Errors were characterized in terms of incident type, contributing factors and consequences. The incidents in the present sample were comprised of runway transgressions, taxiway excursions and ground conflicts. The primary contributing factors were Airport Layout and Markings, Communication and Distraction. In half the incidents the controller issued a new clearance or the flight crew took an evasive action and in the remaining half, no recovery attempt was made because the error was detected after the fact. By gaining a better understanding the factors that affect crew navigation in low visibility and the types of errors that are likely to occur, it will be possible to develop more robust technologies to aid pilots in the ground taxi task. Implications for crew training and procedure development for low-visibility ground taxi are also discussed.

Differences in Characteristics of Aviation Accidents During 1993-2012 Based on Aircraft Type

NASA Technical Reports Server (NTRS)

Evans, Joni K.

2015-01-01

Civilian aircraft are available in a variety of sizes, engine types, construction materials and instrumentation complexity. For the analysis reported here, eleven aircraft categories were developed based mostly on aircraft size and engine type, and these categories were applied to twenty consecutive years of civil aviation accidents. Differences in various factors were examined among these aircraft types, including accident severity, pilot characteristics and accident occurrence categories. In general, regional jets and very light sport aircraft had the lowest rates of adverse outcomes (injuries, fatal accidents, aircraft destruction, major accidents), while aircraft with twin (piston) engines or with a single (piston) engine and retractable landing gear carried the highest incidence of adverse outcomes. The accident categories of abnormal runway contact, runway excursions and non-powerplant system/component failures occur frequently within all but two or three aircraft types. In contrast, ground collisions, loss of control - on ground/water and powerplant system/component failure occur frequently within only one or two aircraft types. Although accidents in larger aircraft tend to have less severe outcomes, adverse outcome rates also differ among accident categories. It may be that the type of accident has as much or more influence on the outcome as the type of aircraft.

Runway incursion severity risk analysis.

DOT National Transportation Integrated Search

2012-09-14

Runway incursions are defined as the unauthorized presence of a vehicle, pedestrian, or aircraft on a runway. Identifying situations or conditions in which runway incursions are more likely to be severe can suggest policy implications and areas for f...

Characterization of the Shuttle Landing Facility as a laser range for testing and evaluation of EO systems

NASA Astrophysics Data System (ADS)

Stromqvist Vetelino, Frida; Borbath, Michael R.; Andrews, Larry C.; Phillips, Ronald L.; Burdge, Geoffrey L.; Chin, Peter G.; Galus, Darren J.; Wayne, David; Pescatore, Robert; Cowan, Doris; Thomas, Frederick

2005-08-01

The Shuttle Landing Facility runway at the Kennedy Space Center in Cape Canaveral, Florida is almost 5 km long and 100 m wide. Its homogeneous environment makes it a unique and ideal place for testing and evaluating EO systems. An experiment, with the goal of characterizing atmospheric parameters on the runway, was conducted in June 2005. Weather data was collected and the refractive index structure parameter was measured with a commercial scintillometer. The inner scale of turbulence was inferred from wind speed measurements and surface roughness. Values of the crosswind speed obtained from the scintillometer were compared with wind measurements taken by a weather station.

Human factors considerations for integrating traffic information on airport moving maps.

DOT National Transportation Integrated Search

2011-05-01

The purpose of this research effort was to identify human factors considerations in the integration of traffic information and surface indications and alerts for runway status on airport moving maps for flight deck displays. The information is primar...

Behavior of aircraft antiskid breaking systems on dry and wet runway surfaces: A slip-ratio-controlled system with ground speed reference from unbraked nose wheel

NASA Technical Reports Server (NTRS)

Tanner, J. A.; Stubbs, S. M.

1977-01-01

An experimental investigation was conducted at the Langley aircraft landing loads and traction facility to study the braking and cornering response of a slip ratio controlled aircraft antiskid braking system with ground speed reference derived from an unbraked nose wheel. The investigation, conducted on dry and wet runway surfaces, utilized one main gear wheel, brake, and tire assembly of a DC-9 series 10 airplane. During maximum braking, the average ratio of the drag force friction coefficient developed by the antiskid system to the maximum drag force friction coefficient available was higher on the dry surface than on damp and flooded surfaces, and was reduced with lighter vertical loads, higher yaw angles, and when new tire treads were replaced by worn treads. Similarly, the average ratio of side force friction coefficient developed by the tire under antiskid control to the maximum side force friction coefficient available to a freely rolling yawed tire decreased with increasing yaw angle, generally increased with ground speed, and decreased when tires with new treads were replaced by those with worn treads.

An analysis of runway incursion "Hot Spots" incidents : with deidentified reports excerpts : volume 2

DOT National Transportation Integrated Search

2002-10-24

The analysis set was limited to runway incursion incidents that occurred : between January 1, 2000 and June 30,2002. : The runway incursion incidents included incidents involving eitherhold : line transgressions or actual runway penetrations. : ...

An analysis of runway incursion "Hot Spots" incidents : with deidentified reports excerpts : volume 1

DOT National Transportation Integrated Search

2002-10-24

The analysis set was limited to runway incursion incidents that occurred : between January 1, 2000 and June 30,2002. : The runway incursion incidents included incidents involving eitherhold : line transgressions or actual runway penetrations. : ...

Aircraft and ground vehicle friction correlation test results obtained under winter runway conditions during joint FAA/NASA Runway Friction Program

NASA Technical Reports Server (NTRS)

Yager, Thomas J.; Vogler, William A.; Baldasare, Paul

1988-01-01

Aircraft and ground vehicle friction data collected during the Joint FAA/NASA Runway Friction Program under winter runway conditions are discussed and test results are summarized. The relationship between the different ground vehicle friction measurements obtained on compacted snow- and ice-covered conditions is defined together with the correlation to aircraft tire friction performance under similar runway conditions.

Benefit Assessment for Metroplex Tactical Runway Configuration Management (mTRCM) in a Simulated Environment

NASA Technical Reports Server (NTRS)

Phojanamongkolkij, Nipa; Oseguera-Lohr, Rosa M.; Lohr, Gary W.; Robbins, Steven W.; Fenbert, James W.; Hartman, Christopher L.

2015-01-01

The System-Oriented Runway Management (SORM) concept is a collection of capabilities focused on a more efficient use of runways while considering all of the factors that affect runway use. Tactical Runway Configuration Management (TRCM), one of the SORM capabilities, provides runway configuration and runway usage recommendations, and monitoring the active runway configuration for suitability given existing factors. This report focuses on the metroplex environment, with two or more proximate airports having arrival and departure operations that are highly interdependent. The myriad of factors that affect metroplex opeations require consideration in arriving at runway configurations that collectively best serve the system as a whole. To assess the metroplex TRCM (mTRCM) benefit, the performance metrics must be compared with the actual historical operations. The historical configuration schedules can be viewed as the schedules produced by subject matter experts (SMEs), and therefore are referred to as the SMEs' schedules. These schedules were obtained from the FAA's Aviation System Performance Metrics (ASPM) database; this is the most representative information regarding runway configuration selection by SMEs. This report focused on a benefit assessment of total delay, transit time, and throughput efficiency (TE) benefits using the mTRCM algorithm at representative volumes for today's traffic at the New York metroplex (N90).

Tire-to-Surface Friction-Coefficient Measurements with a C-123B Airplane on Various Runway Surfaces

NASA Technical Reports Server (NTRS)

Sawyer, Richard H.; Kolnick, Joseph J.

1959-01-01

An investigation was conducted to obtain information on the tire-to-surface friction coefficients available in aircraft braking during the landing run. The tests were made with a C-123B airplane on both wet and dry concrete and bituminous pavements and on snow-covered and ice surfaces at speeds from 12 to 115 knots. Measurements were made of the maximum (incipient skidding) friction coefficient, the full-skidding (locked wheel) friction coefficient, and the wheel slip ratio during braking.

Cockpit Technology for Prevention of General Aviation Runway Incursions

NASA Technical Reports Server (NTRS)

Prinzel, Lawrence J., III; Jones, Denise R.

2007-01-01

General aviation accounted for 74 percent of runway incursions but only 57 percent of the operations during the four-year period from fiscal year (FY) 2001 through FY2004. Elements of the NASA Runway Incursion Prevention System were adapted and tested for general aviation aircraft. Sixteen General Aviation pilots, of varying levels of certification and amount of experience, participated in a piloted simulation study to evaluate the system for prevention of general aviation runway incursions compared to existing moving map displays. Pilots flew numerous complex, high workload approaches under varying weather and visibility conditions. A rare-event runway incursion scenario was presented, unbeknownst to the pilots, which represented a typical runway incursion situation. The results validated the efficacy and safety need for a runway incursion prevention system for general aviation aircraft.

Airport surface traffic control TAGS planning alternatives and cost/benefit

DOT National Transportation Integrated Search

1977-01-01

The findings of a cost/benefit analysis of the deployment of a new airport ground surveillance system TAGS (Tower Automated Ground Surveillance) are presented. TAGS will provide a plain view display of aircraft on the airports taxiways and runways li...

Determination of optimal trajectories for an aircraft returning to the runway following a complete loss of thrust after takeoff

NASA Astrophysics Data System (ADS)

Gordon, Craig A.

This thesis examines the ability of a small, single-engine airplane to return to the runway following an engine failure shortly after takeoff. Two sets of trajectories are examined. One set of trajectories has the airplane fly a straight climb on the runway heading until engine failure. The other set of trajectories has the airplane perform a 90° turn at an altitude of 500 feet and continue until engine failure. Various combinations of wind speed, wind direction, and engine failure times are examined. The runway length required to complete the entire flight from the beginning of the takeoff roll to wheels stop following the return to the runway after engine failure is calculated for each case. The optimal trajectories following engine failure consist of three distinct segments: a turn back toward the runway using a large bank angle and angle of attack; a straight glide; and a reversal turn to align the airplane with the runway. The 90° turn results in much shorter required runway lengths at lower headwind speeds. At higher headwind speeds, both sets of trajectories are limited by the length of runway required for the landing rollout, but the straight climb cases generally require a lower angle of attack to complete the flight. The glide back to the runway is performed at an airspeed below the best glide speed of the airplane due to the need to conserve potential energy after the completion of the turn back toward the runway. The results are highly dependent on the rate of climb of the airplane during powered flight. The results of this study can aid the pilot in determining whether or not a return to the runway could be performed in the event of an engine failure given the specific wind conditions and runway length at the time of takeoff. The results can also guide the pilot in determining the takeoff profile that would offer the greatest advantage in returning to the runway.

75 FR 13336 - Notice of Passenger Facility Charge (PFC) Approvals and Disapprovals

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-19

... Approved for Collection at Key West International Airport (EYW) and Use at EYW: Runway safety area design. Runway safety area construction. Approach clearing--design. Runway obstruction clearing--design. Runway obstruction clearing, phase II--construction. Noise implementation plan, phase 6--design. Noise implementation...

76 FR 77887 - Notice of Passenger Facility Charge (PFC) Approvals and Disapprovals

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-14

... Runway 4/22 extension, environmental assessment Runway 4/22 design--phase 3 Extend runway 4/22...: Snow removal equipment acquisition Airport pavement rehabilitation Master plan update Brief Description of Projects Approved For Collection: Design and permitting for runway 13/31 Easement acquisition...

76 FR 67018 - Notice to Manufacturers of Airport In-Pavement Stationary Runway Weather Information Systems

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-28

...-Pavement Stationary Runway Weather Information Systems AGENCY: Federal Aviation Administration (FAA), U.S. DOT. ACTION: Notice to Manufacturers of In-Pavement Stationary Runway Weather Information Systems... waivers to foreign manufacturers of Active or Passive In- Pavement Stationary Runway Weather Information...

Cognitive issues in head-up displays

NASA Technical Reports Server (NTRS)

Fischer, E.; Haines, R. F.

1980-01-01

The ability of pilots to recognize and act upon unexpected information, presented in either the outside world or in a head-up display (HUD), was evaluated. Eight commercial airline pilots flew 18 approaches with a flightpath-type HUD and 13 approaches with conventional instruments in a fixed-base 727 simulator. The approaches were flown under conditions of low visibility, turbulence, and wind shear. Vertical and lateral flight performance was measured for five cognitive variables: an unexpected obstacle on runway; vertical and lateral boresight-type offset of the HUD; lateral ILS beam bend-type offset; and no anomaly. Mean response time to the runway obstacle was longer with HUD than without it (4.13 vs 1.75 sec.), and two of the pilots did not see the obstacle at all with the HUD. None of the offsets caused any deterioration in lateral flight performance, but all caused some change in vertical tracking; all offsets seemed to magnify the environmental effects. In all conditions, both vertical and lateral tracking was better with the HUD than with the conventional instruments.

NORTHWEST FRONT AND SOUTHWEST SIDE, BUILDING 1933 Edwards Air ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

NORTHWEST FRONT AND SOUTHWEST SIDE, BUILDING 1933 - Edwards Air Force Base, X-15 Engine Test Complex, Observation Bunker Types, Rogers Dry Lake, east of runway between North Base & South Base, Boron, Kern County, CA

14 CFR Appendix E to Part 121 - Flight Training Requirements

Code of Federal Regulations, 2014 CFR

2014-01-01

... takeoff run after reaching a reasonable speed determined by giving due consideration to aircraft characteristics, runway length, surface conditions, wind direction and velocity, brake heat energy, and any other... appropriate speed for nontransport category airplanes For transition training in an airplane group with...

14 CFR 23.925 - Propeller clearance.

Code of Federal Regulations, 2010 CFR

2010-01-01

... deflected and in the level, normal takeoff, or taxing attitude, whichever is most critical. In addition, for... attitude with the critical tire completely deflated and the corresponding landing gear strut bottomed... the runway surface when the airplane is in the maximum pitch attitude attainable during normal...

Greater effort increases perceived value in an invertebrate.

PubMed

Czaczkes, Tomer J; Brandstetter, Birgit; di Stefano, Isabella; Heinze, Jürgen

2018-05-01

Expending effort is generally considered to be undesirable. However, both humans and vertebrates will work for a reward they could also get for free. Moreover, cues associated with high-effort rewards are preferred to low-effort associated cues. Many explanations for these counterintuitive findings have been suggested, including cognitive dissonance (self-justification) or a greater contrast in state (e.g., energy or frustration level) before and after an effort-linked reward. Here, we test whether effort expenditure also increases perceived value in ants, using both classical cue-association methods and pheromone deposition, which correlates with perceived value. In 2 separate experimental setups, we show that pheromone deposition is higher toward the reward that requires more effort: 47% more pheromone deposition was performed for rewards reached via a vertical runway (high effort) compared with ones reached via a horizontal runway (low effort), and deposition rates were 28% higher on rough (high effort) versus smooth (low effort) runways. Using traditional cue-association methods, 63% of ants trained on different surface roughness, and 70% of ants trained on different runway elevations, preferred the high-effort related cues on a Y maze. Finally, pheromone deposition to feeders requiring memorization of one path bifurcation was up to 29% higher than to an identical feeder requiring no learning. Our results suggest that effort affects value perception in ants. This effect may stem from a cognitive process, which monitors the change in a generalized hedonic state before and after reward. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

Development of a Laboratory for Improving Communication between Air Traffic Controllers and Pilots

NASA Technical Reports Server (NTRS)

Brammer, Anthony

2003-01-01

Runway incursions and other surface incidents are known to be significant threats to aviation safety and efficiency. Though the number of near mid-air collisions in U.S. air space has remained unchanged during the last five years, the number of runway incursions has increased and they are almost all due to human error. The three most common factors contributing to air traffic controller and pilot error in airport operations include two that involve failed auditory communication. This project addressed the problems of auditory communication in air traffic control from an acoustical standpoint, by establishing an acoustics laboratory designed for this purpose and initiating research into selected topics that show promise for improving voice communications between air traffic controllers and pilots.

Exploration of the Theoretical Physical Capacity of the John F. Kennedy International Airport Runway System

NASA Technical Reports Server (NTRS)

Neitzke, Kurt W.; Guerreiro, Nelson M.

2014-01-01

A design study was completed to explore the theoretical physical capacity (TPC) of the John F. Kennedy International Airport (KJFK) runway system for a northflow configuration assuming impedance-free (to throughput) air traffic control functionality. Individual runways were modeled using an agent-based, airspace simulation tool, the Airspace Concept Evaluation System (ACES), with all runways conducting both departures and arrivals on a first-come first-served (FCFS) scheduling basis. A realistic future flight schedule was expanded to 3.5 times the traffic level of a selected baseline day, September 26, 2006, to provide a steady overdemand state for KJFK runways. Rules constraining departure and arrival operations were defined to reflect physical limits beyond which safe operations could no longer be assumed. Safety buffers to account for all sources of operational variability were not included in the TPC estimate. Visual approaches were assumed for all arrivals to minimize inter-arrival spacing. Parallel runway operations were assumed to be independent based on lateral spacing distances. Resulting time intervals between successive airport operations were primarily constrained by same-runway and then by intersecting-runway spacing requirements. The resulting physical runway capacity approximates a theoretical limit that cannot be exceeded without modifying runway interaction assumptions. Comparison with current KJFK operational limits for a north-flow runway configuration indicates a substantial throughput gap of approximately 48%. This gap may be further analyzed to determine which part may be feasibly bridged through the deployment of advanced systems and procedures, and which part cannot, because it is either impossible or not cost-effective to control. Advanced systems for bridging the throughput gap may be conceptualized and simulated using this same experimental setup to estimate the level of gap closure achieved.

14 CFR 77.21 - Scope.

Code of Federal Regulations, 2010 CFR

2010-01-01

... airports having defined strips or pathways that are used regularly for the taking off and landing of... takeoff area with no defined pathways for the landing and taking off of aircraft, a determination shall be... pathways. Those pathways so determined shall be considered runways and an appropriate primary surface as...

Measures to increase airfield capacity by changing aircraft runway occupancy characteristics

NASA Technical Reports Server (NTRS)

Gosling, G. D.; Kanafani, A.; Rockaday, S. L. M.

1981-01-01

Airfield capacity and aircraft runway occupancy characteristics were studied. Factors that caused runway congestion and airfield crowding were identified. Several innovations designed to alleviate the congestion are discussed. Integrated landing management, the concept that the operation of the final approach and runway should be considered in concert, was identified as underlying all of the innovations.

KSC-00pp1436

NASA Image and Video Library

2000-09-12

KENNEDY SPACE CENTER, FLA. -- This aerial view shows the approach on Runway 33 at the KSC Shuttle Landing Facility. The runway is 15,000 feet long, with 1,000-foot paved overruns at each end; 300 feet wide (about length of football field), with 50-foot asphalt shoulders each side; 16 inches thick in the center, and 15 inches thick on sides. It has a slope of 24 inches from the center line to the edge for drainage. The single landing strip is considered two runways, depending on approach Runway 15 from northwest, Runway 33 from southeast

KSC00pp1436

NASA Image and Video Library

2000-09-12

KENNEDY SPACE CENTER, FLA. -- This aerial view shows the approach on Runway 33 at the KSC Shuttle Landing Facility. The runway is 15,000 feet long, with 1,000-foot paved overruns at each end; 300 feet wide (about length of football field), with 50-foot asphalt shoulders each side; 16 inches thick in the center, and 15 inches thick on sides. It has a slope of 24 inches from the center line to the edge for drainage. The single landing strip is considered two runways, depending on approach Runway 15 from northwest, Runway 33 from southeast

NASA Research on an Integrated Concept for Airport Surface Operations Management

NASA Technical Reports Server (NTRS)

Gupta, Gautam

2012-01-01

Surface operations at airports in the US are based on tactical operations, where departure aircraft primarily queue up and wait at the departure runways. There have been attempts to address the resulting inefficiencies with both strategic and tactical tools for metering departure aircraft. This presentation gives an overview of Spot And Runway Departure Advisor with Collaborative Decision Making (SARDA-CDM): an integrated strategic and tactical system for improving surface operations by metering departure aircraft. SARDA-CDM is the augmentation of ground and local controller advisories through sharing of flight movement and related operations information between airport operators, flight operators and air traffic control at the airport. The goal is to enhance the efficiency of airport surface operations by exchanging information between air traffic control and airline operators, while minimizing adverse effects on stakeholders and passengers. The presentation motivates the need for departure metering, and provides a brief background on the previous work on SARDA. Then, the concept of operations for SARDA-CDM is described. Then the preliminary results from testing the concept in a real-time automated simulation environment are described. Results indicate benefits such as reduction in taxiing delay and fuel consumption. Further, the preliminary implementation of SARDA-CDM seems robust for two minutes delay in gate push-back times.

Shuttle Challenger landing on Runway 17 at Edwards at end of 51-B mission

NASA Technical Reports Server (NTRS)

1985-01-01

Shuttle Challenger lands on Runway 17 at Edwards at end of 51-B mission. The photo is a rear view of the shuttle landing gear touching the runway, with clouds of dirt trailing behind it. The nose gear is still in the air (071); Side view of the Challenger landing gear touching the runway (072).

SOUTHWEST REAR, SHOWING CLOSED ENTRY HATCH, BUILDING 1934. Looking north ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

SOUTHWEST REAR, SHOWING CLOSED ENTRY HATCH, BUILDING 1934. Looking north - Edwards Air Force Base, X-15 Engine Test Complex, Observation Bunker Types, Rogers Dry Lake, east of runway between North Base & South Base, Boron, Kern County, CA

An assessment of predominant causal factors of pilot deviations that contribute to runway incursions

NASA Astrophysics Data System (ADS)

Campbell, Denado M.

The aim of this study was to identify predominant causal factors of pilot deviations in runway incursions over a two-year period. Runway incursion reports were obtained from NASA's Aviation Safety Reporting System (ASRS), and a qualitative method was used by classifying and coding each report to a specific causal factor(s). The causal factors that were used were substantiated by research from the Aircraft Owner's and Pilot's Association that found that these causal factors were the most common in runway incursion incidents and accidents. An additional causal factor was also utilized to determine the significance of pilot training in relation to runway incursions. From the reports examined, it was found that miscommunication and situational awareness have the greatest impact on pilots and are most often the major causes of runway incursions. This data can be used to assist airports, airlines, and the FAA to understand trends in pilot deviations, and to find solutions for specific problem areas in runway incursion incidents.

14 CFR 139.323 - Traffic and wind direction indicators.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Traffic and wind direction indicators. 139... CERTIFICATION OF AIRPORTS Operations § 139.323 Traffic and wind direction indicators. In a manner authorized by...) A wind cone that visually provides surface wind direction information to pilots. For each runway...

14 CFR 139.323 - Traffic and wind direction indicators.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Traffic and wind direction indicators. 139... CERTIFICATION OF AIRPORTS Operations § 139.323 Traffic and wind direction indicators. In a manner authorized by...) A wind cone that visually provides surface wind direction information to pilots. For each runway...

14 CFR 139.323 - Traffic and wind direction indicators.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Traffic and wind direction indicators. 139... CERTIFICATION OF AIRPORTS Operations § 139.323 Traffic and wind direction indicators. In a manner authorized by...) A wind cone that visually provides surface wind direction information to pilots. For each runway...

Preliminary human factors findings from the FAA Capstone 3 electronic flight bag : airport surface moving map operational evaluation.

DOT National Transportation Integrated Search

2011-05-02

The Federal Aviation Administration (FAA) Office of Runway Safety is interested in understanding the impact of an airport moving map with ownship position on operational usability and safety. To gather data on the use of this technology, the FAA is s...

78 FR 41822 - Public Notice for Waiver of Aeronautical Land-Use Assurance

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-11

...: Notice of intent of waiver with respect to land; Bismarck Municipal Airport, Bismarck, North Dakota... non-aeronautical use and to authorize the sale of airport property located at Bismarck Municipal... outside the approach and departure surfaces of Runway 21 at the Bismarck Municipal Airport, Bismarck, ND...

14 CFR 139.323 - Traffic and wind direction indicators.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Traffic and wind direction indicators. 139... CERTIFICATION OF AIRPORTS Operations § 139.323 Traffic and wind direction indicators. In a manner authorized by...) A wind cone that visually provides surface wind direction information to pilots. For each runway...

14 CFR 139.323 - Traffic and wind direction indicators.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Traffic and wind direction indicators. 139... CERTIFICATION OF AIRPORTS Operations § 139.323 Traffic and wind direction indicators. In a manner authorized by...) A wind cone that visually provides surface wind direction information to pilots. For each runway...

Guidance and control requirements for high-speed Rollout and Turnoff (ROTO)

NASA Technical Reports Server (NTRS)

Goldthorpe, Steve H.; Kernik, Alan C.; Mcbee, Larry S.; Preston, Orv W.

1995-01-01

This report defines the initial requirements for designing a research high-speed rollout and turnoff (ROTO) guidance and control system applicable to transport class aircraft whose purpose is to reduce the average runway occupancy time (ROT) for aircraft operations. The requirements will be used to develop a ROTO system for both automatic and manual piloted operation under normal and reduced visibility conditions. Requirements were determined for nose wheel/rudder steering, braking/reverse thrust, and the navigation system with the aid of a non-real time, three degree-of-freedom MD-11 simulation program incorporating airframe and gear dynamics. The requirements were developed for speeds up to 70 knots using 30 ft exit geometries under dry and wet surface conditions. The requirements were generated under the assumptions that the aircraft landing system meets the current Category III touchdown dispersion requirements and that aircraft interarrival spacing is 2 nautical miles. This effort determined that auto-asymmetric braking is needed to assist steering for aft center-of-gravity aircraft. This report shows various time-history plots of the aircraft performance for the ROTO operation. This effort also investigated the state-of-the-art in the measurement of the runway coefficient of friction for various runway conditions.

Operational Characteristics Identification and Simulation Model Verification for Incheon International Airport

NASA Technical Reports Server (NTRS)

Eun, Yeonju; Jeon, Daekeun; Lee, Hanbong; Zhu, Zhifan; Jung, Yoon C.; Jeong, Myeongsook; Kim, Hyounkyong; Oh, Eunmi; Hong, Sungkwon; Lee, Junwon

2016-01-01

Incheon International Airport (ICN) is one of the hub airports in East Asia. Airport operations at ICN have been growing more than 5% per year in the past five years. According to the current airport expansion plan, a new passenger terminal will be added and the current cargo ramp will be expanded in 2018. This expansion project will bring 77 new stands without adding a new runway to the airport. Due to such continuous growth in airport operations and future expansion of the ramps, it will be highly likely that airport surface traffic will experience more congestion, and therefore, suffer from efficiency degradation. There is a growing awareness in aviation research community of need for strategic and tactical surface scheduling capabilities for efficient airport surface operations. Specific to ICN airport operations, a need for A-CDM (Airport - Collaborative Decision Making) or S-CDM(Surface - Collaborative Decision Making), and controller decision support tools for efficient air traffic management has arisen since several years ago. In the United States, there has been independent research efforts made by academia, industry, and government research organizations to enhance efficiency and predictability of surface operations at busy airports. Among these research activities, the Spot and Runway Departure Advisor (SARDA) developed and tested by National Aeronautics and Space Administration (NASA) is a decision support tool to provide tactical advisories to the controllers for efficient surface operations. The effectiveness of SARDA concept, was successfully verified through the human-in-the-loop (HITL) simulations for both spot release and runway operations advisories for ATC Tower controllers of Dallas/Fort Worth International Airport (DFW) in 2010 and 2012, and gate pushback advisories for the ramp controller of Charlotte/Douglas International Airport (CLT) in 2014. The SARDA concept for tactical surface scheduling is further enhanced and is being integrated into NASA's Airspace Technology Demonstration - 2 (ATD-2) project for technology demonstration of Integrated Arrival/Departure/Surface (ADS) operations at CLT. This study is a part of the international research collaboration between KAIA (Korea Agency for Infrastructure Technology Advancement)/KARI (Korea Aerospace Research Institute) and NASA, which is being conducted to validate the effectiveness of SARDA concept as a controller decision support tool for departure and surface management of ICN. This paper presents the preliminary results of the collaboration effort. It includes investigation of the operational environment of ICN, data analysis for identification of the operational characteristics of the airport, construction and verification of airport simulation model using Surface Operations Simulator and Scheduler (SOSS), NASA's fast-time simulation tool.

Operational Characteristics Identification and Simulation Model Verification for Incheon International Airport

NASA Technical Reports Server (NTRS)

Eun, Yeonju; Jeon, Daekeun; Lee, Hanbong; Zhu, Zhifan; Jung, Yoon C.; Jeong, Myeongsook; Kim, Hyounkyong; Oh, Eunmi; Hong, Sungkwon; Lee, Junwon

2016-01-01

Incheon International Airport (ICN) is one of the hub airports in East Asia. Airport operations at ICN have been growing more than 5 percent per year in the past five years. According to the current airport expansion plan, a new passenger terminal will be added and the current cargo ramp will be expanded in 2018. This expansion project will bring 77 new stands without adding a new runway to the airport. Due to such continuous growth in airport operations and future expansion of the ramps, it will be highly likely that airport surface traffic will experience more congestion, and therefore, suffer from efficiency degradation. There is a growing awareness in aviation research community of need for strategic and tactical surface scheduling capabilities for efficient airport surface operations. Specific to ICN airport operations, a need for A-CDM (Airport - Collaborative Decision Making) or S-CDM (Surface - Collaborative Decision Making), and controller decision support tools for efficient air traffic management has arisen since several years ago. In the United States, there has been independent research efforts made by academia, industry, and government research organizations to enhance efficiency and predictability of surface operations at busy airports. Among these research activities, the Spot and Runway Departure Advisor (SARDA) developed and tested by National Aeronautics and Space Administration (NASA) is a decision support tool to provide tactical advisories to the controllers for efficient surface operations. The effectiveness of SARDA concept, was successfully verified through the human-in-the-loop (HITL) simulations for both spot release and runway operations advisories for ATC Tower controllers of Dallas-Fort Worth International Airport (DFW) in 2010 and 2012, and gate pushback advisories for the ramp controller of Charlotte-Douglas International Airport (CLT) in 2014. The SARDA concept for tactical surface scheduling is further enhanced and is being integrated into NASA's Airspace Technology Demonstration-2 (ATD-2) project for technology demonstration of Integrated Arrival-Departure-Surface (IADS) operations at CLT. This study is a part of the international research collaboration between KAIA (Korea Agency for Infrastructure Technology Advancement), KARI (Korea Aerospace Research Institute) and NASA, which is being conducted to validate the effectiveness of SARDA concept as a controller decision support tool for departure and surface management of ICN. This paper presents the preliminary results of the collaboration effort. It includes investigation of the operational environment of ICN, data analysis for identification of the operational characteristics of the airport, construction and verification of airport simulation model using Surface Operations Simulator and Scheduler (SOSS), NASA's fast-time simulation tool.

76 FR 12404 - Noise Exposure Map Notice; Jackson-Evers International Airport, Jackson, MS

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-07

...-2, Runways 16L/16R Radar and Modeled Flight Tracks for Departures and Arrivals; Figure 5-3, Runways 34L/34R Radar and Modeled Flight Tracks for Departures and Arrivals; Figure 5-4, Runways 16L/16R Radar and Modeled Flight Tracks for Flight Patterns; Figure 5-5, Runways 34L/34R Radar and Modeled Flight...

77 FR 64580 - Noise Exposure Map Notice for Van Nuys Airport, Van Nuys, California

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-22

... for VNY; Figure 10, Modeled Flight Tracks for Runway 16R and 34L Jet Arrivals; Figure 11, Modeled Flight Tracks for Runway 16R and 34L Jet Departures; Figure 12, Modeled Flight Tracks for Runway 16R and 34L Propeller Arrivals; Figure 13, Modeled Flight Tracks for Runway 16L and 34R Propeller Arrivals...

View of Facility No. S359 (Seaplane Ramp 3), with Koolau ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View of Facility No. S359 (Seaplane Ramp 3), with Koolau Mountain Range in background - U.S. Naval Base, Pearl Harbor, Seaplane Runways-1933 Type, South shore of Ford Island, near Lexington Boulevard, Pearl City, Honolulu County, HI

Surface Effect Takeoff and Landing System (SETOLS)

DTIC Science & Technology

1974-04-01

State-of-the-Art 33 4. Program Tranisfer ~34 5. Future Research 34 6. Current Organizational Contacts and Identification 36 I REFE~RENCES 37 DEFENSE...ability to taxi over water, mud, low tree stumps, and empty and water-filled ditches. The flight tests indicated no significant changes in the...flight Lested from hard--surface runways, turf, water, snow, and fine sand. The aircraft also demonstrated the ability to taxi across mud, low tree

Rollout and Turnoff (ROTO) Guidance and Information Displays: Effect on Runway Occupancy Time in Simulated Low-Visibility Landings

NASA Technical Reports Server (NTRS)

Hueschen, Richard M.; Hankins, Walter W., III; Barker, L. Keith

2001-01-01

This report examines a rollout and turnoff (ROTO) system for reducing the runway occupancy time for transport aircraft in low-visibility weather. Simulator runs were made to evaluate the system that includes a head-up display (HUD) to show the pilot a graphical overlay of the runway along with guidance and steering information to a chosen exit. Fourteen pilots (airline, corporate jet, and research pilots) collectively flew a total of 560 rollout and turnoff runs using all eight runways at Hartsfield Atlanta International Airport. The runs consisted of 280 runs for each of two runway visual ranges (RVRs) (300 and 1200 ft). For each visual range, half the runs were conducted with the HUD information and half without. For the runs conducted with the HUD information, the runway occupancy times were lower and more consistent. The effect was more pronounced as visibility decreased. For the 1200-ft visibility, the runway occupancy times were 13% lower with HUD information (46.1 versus 52.8 sec). Similarly, for the 300-ft visibility, the times were 28% lower (45.4 versus 63.0 sec). Also, for the runs with HUD information, 78% (RVR 1200) and 75% (RVR 300) had runway occupancy times less than 50 sec, versus 41 and 20%, respectively, without HUD information.

Federal Aviation Administration's Runway Incursion Program

DOT National Transportation Integrated Search

1997-12-08

To reverse the upward trend in runway incursions, FAA must have a strong : Runway Incursion Program to solve systemwide problems and expedite : solutions. The Office of Inspector General report recommends that FAA (1) assign specific responsibility f...

Aviation infrastructure : challenges associated with building and maintaining runways

DOT National Transportation Integrated Search

2000-10-05

This testimony focuses on challenges associated with building new runways and with ensuring that existing runways are properly maintained. Recent flight delays and cancellations as well as significant media attention to them have heightened public co...

Comparison of Procedures for Dual and Triple Closely Spaced Parallel Runways

NASA Technical Reports Server (NTRS)

Verma, Savita; Ballinger, Deborah; Subramanian Shobana; Kozon, Thomas

2012-01-01

A human-in-the-loop high fidelity flight simulation experiment was conducted, which investigated and compared breakout procedures for Very Closely Spaced Parallel Approaches (VCSPA) with two and three runways. To understand the feasibility, usability and human factors of two and three runway VCSPA, data were collected and analyzed on the dependent variables of breakout cross track error and pilot workload. Independent variables included number of runways, cause of breakout and location of breakout. Results indicated larger cross track error and higher workload using three runways as compared to 2-runway operations. Significant interaction effects involving breakout cause and breakout location were also observed. Across all conditions, cross track error values showed high levels of breakout trajectory accuracy and pilot workload remained manageable. Results suggest possible avenues of future adaptation for adopting these procedures (e.g., pilot training), while also showing potential promise of the concept.

The Effects of Weather on Rapid Runway Repair. Volume 1

DTIC Science & Technology

1983-05-01

stress include chronic heat exhaustion, forms of tropical dermatosis , and renal stones. Interestingly, no chronic physiological failures resulting from...kcal/m2 /hr as described by Lowry), or 90 kcal/hr or 105 watts for the average adult male (with 1.8 m2 of body surface area). Normal work is expected

Managing Earthworm Castings (Oligochaeta: Lumbricidae) in Turfgrass using a Natural By-Product of Tea Oil (Camellia sp.) Manufacture

USDA-ARS?s Scientific Manuscript database

Earthworm casts are a problem on golf courses and sport fields when they disrupt the playability, aesthetics, and maintenance of playing surfaces. Abundant earthworms alongside airport runways can increase bird strike risk. Currently no pesticides are labeled for earthworms in the United States. W...

14 CFR Appendix E to Part 121 - Flight Training Requirements

Code of Federal Regulations, 2013 CFR

2013-01-01

... reasonable speed determined by giving due consideration to aircraft characteristics, runway length, surface conditions, wind direction and velocity, brake heat energy, and any other pertinent factors that may... 1 when V 1 and V 2 or V 1 and V R are identical; or (3) At the appropriate speed for nontransport...

14 CFR Appendix E to Part 121 - Flight Training Requirements

Code of Federal Regulations, 2012 CFR

2012-01-01

... reasonable speed determined by giving due consideration to aircraft characteristics, runway length, surface conditions, wind direction and velocity, brake heat energy, and any other pertinent factors that may... 1 when V 1 and V 2 or V 1 and V R are identical; or (3) At the appropriate speed for nontransport...

NASA Langley's Aircraft Landing Dynamics Facility

NASA Technical Reports Server (NTRS)

Davis, Pamela A.

1993-01-01

The Aircraft Landing Dynamics Facility (ALDF) is a unique facility with the ability to test aircraft landing gear systems on actual runway surfaces at operational ground speeds and loading conditions. A brief historical overview of the original Landing Loads Track (LLT) is given, followed by a detailed description of the new ALDF systems and operational capabilities.

A transformation method for deriving from a photograph, position and heading of a vehicle in a plane

NASA Technical Reports Server (NTRS)

Sleeper, R. K.; Smith, E. G.

1976-01-01

Equations have been derived that transform perspectively viewed planar surface coordinates, as seen in a photograph, into coordinates of the original plane surface. These transformation equations are developed in terms of nine geometric variables that define the photographic setup and are redefined in terms of eight parameters. The parameters are then treated as independent quantities that fully characterize the transformation and are expressed directly in terms of the four corner coordinates of a reference rectangle in the object plane and their coordinates as seen in a photograph. Vehicle position is determined by transforming the perspectively viewed coordinate position of a representative vehicle target into runway coordinates. Vehicle heading is determined from the runway coordinates of two vehicle target points. When the targets are elevated above the plane of the reference grid, the computation of the heading angle is unaffected; however, the computation of the target position may require adjustment of two parameters. Methods are given for adjusting the parameters for elevation and an example is included for both nonelevated and elevated target conditions.

European Action Plan for the Prevention of Runway Incursions

DOT National Transportation Integrated Search

2017-11-20

This version of European Action Plan for the Prevention of Runway Incursions (EAPPRI) recognises the emergence of EU provisions intended to improve runway safety in Europe. However, like its predecessors, this third version of EAPPRI continues to rec...

Runway Scheduling for Charlotte Douglas International Airport

NASA Technical Reports Server (NTRS)

Malik, Waqar A.; Lee, Hanbong; Jung, Yoon C.

2016-01-01

This paper describes the runway scheduler that was used in the 2014 SARDA human-in-the-loop simulations for CLT. The algorithm considers multiple runways and computes optimal runway times for departures and arrivals. In this paper, we plan to run additional simulation on the standalone MRS algorithm and compare the performance of the algorithm against a FCFS heuristic where aircraft avail of runway slots based on a priority given by their positions in the FCFS sequence. Several traffic scenarios corresponding to current day traffic level and demand profile will be generated. We also plan to examine the effect of increase in traffic level (1.2x and 1.5x) and observe trends in algorithm performance.

KSC-04PD-0937

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. This aerial photo of the runway at the KSC Shuttle Landing Facility looks northeast. Longer and wider than most commercial runways, it is 15,000 feet long, with 1,000- foot paved overruns on each end, and 300 feet wide, with 50-foot asphalt shoulders. The runway is used by military and civilian cargo carriers, astronauts T-38 trainers, Shuttle Training Aircraft and helicopters, as well as the Space Shuttle. At center right is the parking apron with the orbiter mate/demate tower. The tow-way stretches from the runway to the right, passing the hangar and storage facilities. A grassy area next to the mid- point of the runway is where the new control tower is located.

KSC-04PD-0938

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. This aerial photo of the runway at the KSC Shuttle Landing Facility looks northeast. Longer and wider than most commercial runways, it is 15,000 feet long, with 1,000- foot paved overruns on each end, and 300 feet wide, with 50-foot asphalt shoulders. The runway is used by military and civilian cargo carriers, astronauts T-38 trainers, Shuttle Training Aircraft and helicopters, as well as the Space Shuttle. At center right is the parking apron with the orbiter mate/demate tower. The tow-way stretches from the runway to the right, passing the hangar and storage facilities. A grassy area next to the mid- point of the runway is where the new control tower is located.

KSC-04pd0938

NASA Image and Video Library

2004-03-31

KENNEDY SPACE CENTER, FLA. - This aerial photo of the runway at the KSC Shuttle Landing Facility looks northeast. Longer and wider than most commercial runways, it is 15,000 feet long, with 1,000-foot paved overruns on each end, and 300 feet wide, with 50-foot asphalt shoulders. The runway is used by military and civilian cargo carriers, astronauts’ T-38 trainers, Shuttle Training Aircraft and helicopters, as well as the Space Shuttle. At center right is the parking apron with the orbiter mate/demate tower. The tow-way stretches from the runway to the right, passing the hangar and storage facilities. A grassy area next to the mid-point of the runway is where the new control tower is located.

KSC-04pd0937

NASA Image and Video Library

2004-03-31

KENNEDY SPACE CENTER, FLA. - This aerial photo of the runway at the KSC Shuttle Landing Facility looks northeast. Longer and wider than most commercial runways, it is 15,000 feet long, with 1,000-foot paved overruns on each end, and 300 feet wide, with 50-foot asphalt shoulders. The runway is used by military and civilian cargo carriers, astronauts’ T-38 trainers, Shuttle Training Aircraft and helicopters, as well as the Space Shuttle. At center right is the parking apron with the orbiter mate/demate tower. The tow-way stretches from the runway to the right, passing the hangar and storage facilities. A grassy area next to the mid-point of the runway is where the new control tower is located.

Electronic System for Preventing Airport Runway Incursions

NASA Technical Reports Server (NTRS)

Dabney, Richard; Elrod, Susan

2009-01-01

A proposed system of portable illuminated signs, electronic monitoring equipment, and radio-communication equipment for preventing (or taking corrective action in response to) improper entry of aircraft, pedestrians, or ground vehicles onto active airport runways is described. The main overall functions of the proposed system would be to automatically monitor aircraft ground traffic on or approaching runways and to generate visible and/or audible warnings to affected pilots, ground-vehicle drivers, and control-tower personnel when runway incursions take place.

Throughput Benefit Assessment for Tactical Runway Configuration Management (TRCM)

NASA Technical Reports Server (NTRS)

Phojanamongkolkij, Nipa; Oseguera-Lohr, Rosa M.; Lohr, Gary W.; Fenbert, James W.

2014-01-01

The System-Oriented Runway Management (SORM) concept is a collection of needed capabilities focused on a more efficient use of runways while considering all of the factors that affect runway use. Tactical Runway Configuration Management (TRCM), one of the SORM capabilities, provides runway configuration and runway usage recommendations, monitoring the active runway configuration for suitability given existing factors, based on a 90 minute planning horizon. This study evaluates the throughput benefits using a representative sample of today's traffic volumes at three airports: Memphis International Airport (MEM), Dallas-Fort Worth International Airport (DFW), and John F. Kennedy International Airport (JFK). Based on this initial assessment, there are statistical throughput benefits for both arrivals and departures at MEM with an average of 4% for arrivals, and 6% for departures. For DFW, there is a statistical benefit for arrivals with an average of 3%. Although there is an average of 1% benefit observed for departures, it is not statistically significant. For JFK, there is a 12% benefit for arrivals, but a 2% penalty for departures. The results obtained are for current traffic volumes and should show greater benefit for increased future demand. This paper also proposes some potential TRCM algorithm improvements for future research. A continued research plan is being worked to implement these improvements and to re-assess the throughput benefit for today and future projected traffic volumes.

AERIAL OF SHUTTLE LANDING FACILITY [SLF] POURING CONCRETE ON RUNWAY

NASA Technical Reports Server (NTRS)

1975-01-01

AERIAL OF SHUTTLE LANDING FACILITY [SLF] POURING CONCRETE ON RUNWAY KSC-375C-10036.32 108-KSC-375C-10036.32, P-21425, ARCHIVE-04501 Aerial oblique of Shuttle Landing Facility. Pouring concrete on runway. Direction North - Altitude 100'.

47 CFR 87.213 - Scope of service.

Code of Federal Regulations, 2011 CFR

2011-10-01

... control (ATC) purposes other than to relay ATC information between the pilot and air traffic controller... runways, types of fuel available, wind conditions, weather information, dispatching, or other necessary information. At any airport at which a control tower, control tower remote communications outlet station (RCO...

47 CFR 87.213 - Scope of service.

Code of Federal Regulations, 2010 CFR

2010-10-01

... control (ATC) purposes other than to relay ATC information between the pilot and air traffic controller... runways, types of fuel available, wind conditions, weather information, dispatching, or other necessary information. At any airport at which a control tower, control tower remote communications outlet station (RCO...

Runway Scheduling Using Generalized Dynamic Programming

NASA Technical Reports Server (NTRS)

Montoya, Justin; Wood, Zachary; Rathinam, Sivakumar

2011-01-01

A generalized dynamic programming method for finding a set of pareto optimal solutions for a runway scheduling problem is introduced. The algorithm generates a set of runway fight sequences that are optimal for both runway throughput and delay. Realistic time-based operational constraints are considered, including miles-in-trail separation, runway crossings, and wake vortex separation. The authors also model divergent runway takeoff operations to allow for reduced wake vortex separation. A modeled Dallas/Fort Worth International airport and three baseline heuristics are used to illustrate preliminary benefits of using the generalized dynamic programming method. Simulated traffic levels ranged from 10 aircraft to 30 aircraft with each test case spanning 15 minutes. The optimal solution shows a 40-70 percent decrease in the expected delay per aircraft over the baseline schedulers. Computational results suggest that the algorithm is promising for real-time application with an average computation time of 4.5 seconds. For even faster computation times, two heuristics are developed. As compared to the optimal, the heuristics are within 5% of the expected delay per aircraft and 1% of the expected number of runway operations per hour ad can be 100x faster.

AERIAL OF SHUTTLE LANDING FACILITY [SLF] RUNWAY CONSTRUCTION

NASA Technical Reports Server (NTRS)

1974-01-01

AERIAL OF SHUTTLE LANDING FACILITY [SLF] RUNWAY CONSTRUCTION KSC-374C-10236.33 108-KSC-374C-10236.33, P-15911, ARCHIVE-04477 Shuttle runway facility construction progress - oblique vertical, altitude 3,000 ft. time 1030 - direction south - south half from center.

14 CFR 77.2 - Definition of terms.

Code of Federal Regulations, 2010 CFR

2010-01-01

... planning document or military service military airport planning document. Precision instrument runway means... military airport layout plan; any other FAA planning document, or military service military airport planning document. Utility runway means a runway that is constructed for and intended to be used by...

Pilot Evaluations of Runway Status Light System

NASA Technical Reports Server (NTRS)

Young, Steven D.; Wills, Robert W.; Smith, R. Marshall

1996-01-01

This study focuses on use of the Transport Systems Research Vehicle (TSRV) Simulator at the Langley Research Center to obtain pilot opinion and input on the Federal Aviation Administration's Runway Status Light System (RWSL) prior to installation in an operational airport environment. The RWSL has been designed to reduce the likelihood of runway incursions by visually alerting pilots when a runway is occupied. Demonstrations of the RWSL in the TSRV Simulator allowed pilots to evaluate the system in a realistic cockpit environment.

Use of Very Weak Radiation Sources to Determine Aircraft Runway Position

NASA Technical Reports Server (NTRS)

Drinkwater, Fred J., III; Kibort, Bernard R.

1965-01-01

Various methods of providing runway information in the cockpit during the take-off and landing roll have been proposed. The most reliable method has been to use runway distance markers when visible. Flight tests were used to evaluate the feasibility of using weak radio-active sources to trigger a runway distance counter in the cockpit. The results of these tests indicate that a weak radioactive source would provide a reliable signal by which this indicator could be operated.

Precision Positional Data of General Aviation Air Traffic in Terminal Air Space

NASA Technical Reports Server (NTRS)

Melson, W. E., Jr.; Parker, L. C.; Northam, A. M.; Singh, R. P.

1978-01-01

Three dimensional radar tracks of general aviation air traffic at three uncontrolled airports are considered. Contained are data which describe the position-time histories, other derived parameters, and reference data for the approximately 1200 tracks. All information was correlated such that the date, time, flight number, and runway number match the pattern type, aircraft type, wind, visibility, and cloud conditions.

Evaluation of Alternate Concepts for Synthetic Vision Flight Displays With Weather-Penetrating Sensor Image Inserts During Simulated Landing Approaches

NASA Technical Reports Server (NTRS)

Parrish, Russell V.; Busquets, Anthony M.; Williams, Steven P.; Nold, Dean E.

2003-01-01

A simulation study was conducted in 1994 at Langley Research Center that used 12 commercial airline pilots repeatedly flying complex Microwave Landing System (MLS)-type approaches to parallel runways under Category IIIc weather conditions. Two sensor insert concepts of 'Synthetic Vision Systems' (SVS) were used in the simulated flights, with a more conventional electro-optical display (similar to a Head-Up Display with raster capability for sensor imagery), flown under less restrictive visibility conditions, used as a control condition. The SVS concepts combined the sensor imagery with a computer-generated image (CGI) of an out-the-window scene based on an onboard airport database. Various scenarios involving runway traffic incursions (taxiing aircraft and parked fuel trucks) and navigational system position errors (both static and dynamic) were used to assess the pilots' ability to manage the approach task with the display concepts. The two SVS sensor insert concepts contrasted the simple overlay of sensor imagery on the CGI scene without additional image processing (the SV display) to the complex integration (the AV display) of the CGI scene with pilot-decision aiding using both object and edge detection techniques for detection of obstacle conflicts and runway alignment errors.

Flight test of takeoff performance monitoring system

NASA Technical Reports Server (NTRS)

Middleton, David B.; Srivatsan, Raghavachari; Person, Lee H., Jr.

1994-01-01

The Takeoff Performance Monitoring System (TOPMS) is a computer software and hardware graphics system that visually displays current runway position, acceleration performance, engine status, and other situation advisory information to aid pilots in their decision to continue or to abort a takeoff. The system was developed at the Langley Research Center using the fixed-base Transport Systems Research Vehicle (TSRV) simulator. (The TSRV is a highly modified Boeing 737-100 research airplane.) Several versions of the TOPMS displays were evaluated on the TSRV B-737 simulator by more than 40 research, United States Air Force, airline and industry and pilots who rated the system satisfactory and recommended further development and testing. In this study, the TOPMS was flight tested on the TSRV. A total of 55 takeoff and 30 abort situations were investigated at 5 airfields. TOPMS displays were observed on the navigation display screen in the TSRV research flight deck during various nominal and off-nominal situations, including normal takeoffs; reduced-throttle takeoffs; induced-acceleration deficiencies; simulated-engine failures; and several gross-weight, runway-geometry, runway-surface, and ambient conditions. All tests were performed on dry runways. The TOPMS software executed accurately during the flight tests and the displays correctly depicted the various test conditions. Evaluation pilots found the displays easy to monitor and understand. The algorithm provides pretakeoff predictions of the nominal distances that are needed to accelerate the airplane to takeoff speed and to brake it to a stop; these predictions agreed reasonably well with corresponding values measured during several fully executed and aborted takeoffs. The TOPMS is operational and has been retained on the TSRV for general use and demonstration.

The application of magnetic measurements for the characterization of atmospheric particulate pollution within the airport environment.

PubMed

Jones, S; Richardson, N; Bennett, M; Hoon, S R

2015-01-01

The significant increase in global air travel which has occurred during the last fifty years has generated growing concern regarding the potential impacts associated with increasing emissions of atmospheric particulate matter (PM) on health and the environment. PM within the airport environment may be derived from a range of sources. To date, however, the identification of individual sources of airport derived PM has remained elusive but constitutes a research priority for the aviation industry.The aim of this research was to identify distinctive and characteristic fingerprints of atmospheric PM derived from various sources in an airport environment through the use of environmental magnetic measurements. PM samples from aircraft engine emissions, brake wear and tire wear residues have been obtained from a range of different aircraft and engine types. Samples have been analyzed utilizing a range of magnetic mineral properties indicative of magnetic mineralogy and grain size. Results indicate that the dusts from the three 'aircraft' sources, (i.e. engines, brakes and tires) display distinctive magnetic mineral characteristics which may serve as 'magnetic fingerprints' for these sources. Magnetic measurements of runway dusts collected at different locations on the runway surface also show contrasting magnetic characteristics which, when compared with those of the aircraft-derived samples, suggest that they may relate to different sources characteristic of aircraft emissions at various stages of the take-off/landing cycle. The findings suggest that magnetic measurements could have wider applicability for the differentiation and identification of PM within the airport environment.

AERIAL OF SHUTTLE LANDING FACILITY [SLF] RUNWAY AND PARKING APRON

NASA Technical Reports Server (NTRS)

1974-01-01

AERIAL OF SHUTTLE LANDING FACILITY [SLF] RUNWAY AND PARKING APRON KSC-374C-10236.23 108-KSC-374C-10236.23, P-15909, ARCHIVE-04476 Shuttle runway facility construction progress - oblique vertical, altitude 1,000 ft. Time 1100 - direction E - Shuttle Park area.

76 FR 12405 - Notice of Passenger Facility Charge (PFC) Approvals and Disapprovals

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-07

.... Mandatory pavement markings. Airport signage. Runway guard lights. Wildlife study. PFC application.... Runway 18/36 pavement maintenance. Runway 13/31 pavement maintenance. PFC administration fees. Brief... Use: Tractor with snow blower and snow plow. Airport security and access control upgrades--design...

Human risk factors associated with pilots in runway excursions.

PubMed

Chang, Yu-Hern; Yang, Hui-Hua; Hsiao, Yu-Jung

2016-09-01

A breakdown analysis of civil aviation accidents worldwide indicates that the occurrence of runway excursions represents the largest portion among all aviation occurrence categories. This study examines the human risk factors associated with pilots in runway excursions, by applying a SHELLO model to categorize the human risk factors and to evaluate the importance based on the opinions of 145 airline pilots. This study integrates aviation management level expert opinions on relative weighting and improvement-achievability in order to develop four kinds of priority risk management strategies for airline pilots to reduce runway excursions. The empirical study based on experts' evaluation suggests that the most important dimension is the liveware/pilot's core ability. From the perspective of front-line pilots, the most important risk factors are the environment, wet/containment runways, and weather issues like rain/thunderstorms. Finally, this study develops practical strategies for helping management authorities to improve major operational and managerial weaknesses so as to reduce the human risks related to runway excursions. Copyright © 2016 Elsevier Ltd. All rights reserved.

Operational Concept for Flight Crews to Participate in Merging and Spacing of Aircraft

NASA Technical Reports Server (NTRS)

Baxley, Brian T.; Barmore, Bryan E.; Abbott, Terence S.; Capron, William R.

2006-01-01

The predicted tripling of air traffic within the next 15 years is expected to cause significant aircraft delays and create a major financial burden for the airline industry unless the capacity of the National Airspace System can be increased. One approach to improve throughput and reduce delay is to develop new ground tools, airborne tools, and procedures to reduce the variance of aircraft delivery to the airport, thereby providing an increase in runway throughput capacity and a reduction in arrival aircraft delay. The first phase of the Merging and Spacing Concept employs a ground based tool used by Air Traffic Control that creates an arrival time to the runway threshold based on the aircraft s current position and speed, then makes minor adjustments to that schedule to accommodate runway throughput constraints such as weather and wake vortex separation criteria. The Merging and Spacing Concept also employs arrival routing that begins at an en route metering fix at altitude and continues to the runway threshold with defined lateral, vertical, and velocity criteria. This allows the desired spacing interval between aircraft at the runway to be translated back in time and space to the metering fix. The tool then calculates a specific speed for each aircraft to fly while enroute to the metering fix based on the adjusted land timing for that aircraft. This speed is data-linked to the crew who fly this speed, causing the aircraft to arrive at the metering fix with the assigned spacing interval behind the previous aircraft in the landing sequence. The second phase of the Merging and Spacing Concept increases the timing precision of the aircraft delivery to the runway threshold by having flight crews using an airborne system make minor speed changes during enroute, descent, and arrival phases of flight. These speed changes are based on broadcast aircraft state data to determine the difference between the actual and assigned time interval between the aircraft pair. The airborne software then calculates a speed adjustment to null that difference over the remaining flight trajectory. Follow-on phases still under development will expand the concept to all types of aircraft, arriving from any direction, merging at different fixes and altitudes, and to any airport. This paper describes the implementation phases of the Merging and Spacing Concept, and provides high-level results of research conducted to date.

Parallel runway requirement analysis study. Volume 1: The analysis

NASA Technical Reports Server (NTRS)

Ebrahimi, Yaghoob S.

1993-01-01

The correlation of increased flight delays with the level of aviation activity is well recognized. A main contributor to these flight delays has been the capacity of airports. Though new airport and runway construction would significantly increase airport capacity, few programs of this type are currently underway, let alone planned, because of the high cost associated with such endeavors. Therefore, it is necessary to achieve the most efficient and cost effective use of existing fixed airport resources through better planning and control of traffic flows. In fact, during the past few years the FAA has initiated such an airport capacity program designed to provide additional capacity at existing airports. Some of the improvements that that program has generated thus far have been based on new Air Traffic Control procedures, terminal automation, additional Instrument Landing Systems, improved controller display aids, and improved utilization of multiple runways/Instrument Meteorological Conditions (IMC) approach procedures. A useful element to understanding potential operational capacity enhancements at high demand airports has been the development and use of an analysis tool called The PLAND_BLUNDER (PLB) Simulation Model. The objective for building this simulation was to develop a parametric model that could be used for analysis in determining the minimum safety level of parallel runway operations for various parameters representing the airplane, navigation, surveillance, and ATC system performance. This simulation is useful as: a quick and economical evaluation of existing environments that are experiencing IMC delays, an efficient way to study and validate proposed procedure modifications, an aid in evaluating requirements for new airports or new runways in old airports, a simple, parametric investigation of a wide range of issues and approaches, an ability to tradeoff air and ground technology and procedures contributions, and a way of considering probable blunder mechanisms and range of blunder scenarios. This study describes the steps of building the simulation and considers the input parameters, assumptions and limitations, and available outputs. Validation results and sensitivity analysis are addressed as well as outlining some IMC and Visual Meteorological Conditions (VMC) approaches to parallel runways. Also, present and future applicable technologies (e.g., Digital Autoland Systems, Traffic Collision and Avoidance System II, Enhanced Situational Awareness System, Global Positioning Systems for Landing, etc.) are assessed and recommendations made.

Airplane takeoff and landing performance monitoring system

NASA Technical Reports Server (NTRS)

Middleton, David B. (Inventor); Srivatsan, Raghavachari (Inventor); Person, Lee H. (Inventor)

1989-01-01

The invention is a real-time takeoff and landing performance monitoring system which provides the pilot with graphic and metric information to assist in decisions related to achieving rotation speed (V sub R) within the safe zone of the runway or stopping the aircraft on the runway after landing or take off abort. The system processes information in two segments: a pretakeoff segment and a real-time segment. One-time inputs of ambient conditions and airplane configuration information are used in the pretakeoff segment to generate scheduled performance data. The real-time segment uses the scheduled performance data, runway length data and transducer measured parameters to monitor the performance of the airplane throughout the takeoff roll. An important feature of this segment is that it updates the estimated runway rolling friction coefficient. Airplane performance predictions also reflect changes in headwind occurring as the takeoff roll progresses. The system displays the position of the airplane on the runway, indicating runway used and runway available, summarizes the critical information into a situation advisory flag, flags engine failures and off-nominal acceleration performance, and indicates where on the runway particular events such as decision speed (V sub 1), rotation speed (V sub R) and expected stop points will occur based on actual or predicted performance. The display also indicates airspeed, wind vector, engine pressure ratios, second segment climb speed, and balanced field length (BFL). The system detects performance deficiencies by comparing the airplane's present performance with a predicted nominal performance based upon the given conditions.

14 CFR 61.67 - Category II pilot authorization requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... and runway lighting system; (ix) Characteristics and limitations of the flight director system, auto approach coupler (including split axis type if equipped), auto throttle system (if equipped), and other... be made with the use of an approved flight control guidance system, except if an approved auto...

29 CFR 1910.68 - Manlifts.

Code of Federal Regulations, 2013 CFR

2013-07-01

... circuit directly they shall be of the multipole type. (b) Where electronic devices are used they shall be... will be forced straight, tripping the switch and opening the electrical circuit. (8) Step (platform). A... at landings.) (ii) Control of illumination. Lighting of manlift runways shall be by means of circuits...

Elements affecting runway traction

NASA Technical Reports Server (NTRS)

Horne, W. B.

1974-01-01

The five basic elements affecting runway traction for jet transport aircraft operation are identified and described in terms of pilot, aircraft system, atmospheric, tire, and pavement performance factors or parameters. Where possible, research results are summarized, and means for restoring or improving runway traction for these different conditions are discussed.

Measurement of Vehicle Tire-to-Road Coefficient of Friction with a Portable Microcomputerized Transducer.

DTIC Science & Technology

1982-08-01

Sliding Rubber and the Load Dependance of Road Tyre Friction," The Physics of Tire Tractio,’. Theory, and Experiment (Hays, D. F., and Brown, A. L...Saturation of Sliding Rubber and the Load Dependance of Road Tyre Friction," The Physics of Tire Traction, Theory, and Expe-iment (Hays, D. F., and...surfaces could be identified and evaluated before accidents happen or runway surfaces could be evaluated to determine if rubber or other contaminant

Runway Rubber Removal Specification Development: Field Evaluation Procedures Development.

DTIC Science & Technology

1984-07-01

removal was sufficient enough to restore full pave- ment skid resistance (based on tests with a DBV). With regard to high-pressure water rubber ...over a test surface, the rubber slider resists motion-. The force, parallel to the test surface, which acts on the slider registers an output on a dial...PROCEDURE 1. Check rubber shoe for wear . Replace when the edge is worn by more than 3/16 in as measured with a rule laid flat across the slider width. 2

14 CFR 151.9 - Runway clear zones: General.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Runway clear zones: General. 151.9 Section 151.9 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED... above the elevation of the runway or 50 feet above the terrain at the outer extremity of the clear zone...

14 CFR 151.9 - Runway clear zones: General.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Runway clear zones: General. 151.9 Section 151.9 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED... above the elevation of the runway or 50 feet above the terrain at the outer extremity of the clear zone...

14 CFR 151.9 - Runway clear zones: General.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Runway clear zones: General. 151.9 Section 151.9 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED... above the elevation of the runway or 50 feet above the terrain at the outer extremity of the clear zone...

14 CFR 151.9 - Runway clear zones: General.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Runway clear zones: General. 151.9 Section 151.9 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED... above the elevation of the runway or 50 feet above the terrain at the outer extremity of the clear zone...

14 CFR 151.9 - Runway clear zones: General.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Runway clear zones: General. 151.9 Section 151.9 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED... above the elevation of the runway or 50 feet above the terrain at the outer extremity of the clear zone...

14 CFR 121.171 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-01-01

... point at which the obstruction clearance plane associated with the approach end of the runway intersects... clearance plane means a plane sloping upward from the runway at a slope of 1:20 to the horizontal, and... centerline of the runway, beginning at the point where the obstruction clearance plane intersects the...

Runway image shape as a cue for judgment of approach angle.

DOT National Transportation Integrated Search

1979-11-01

One cue for visual judgment of glidepath angle has been referred to as form ratio. Form ratio is defined as the ratio of vertical height of the runway to width of the far end in the runway retinal image. The ability of pilots to judge form ratios was...

Distribution of Monochrome Screen Luminance in the CTOL Visual Technology Research Simulator.

DTIC Science & Technology

1980-11-01

runway lines 3.8 4.2 8. Carrier runway 2.5 3.5 9. FLOLS* Meatball ** 2.0 2.4 10. FLOLS Background 0.68 1.3 *Fresnal Lens Optical Landing System...Standard U.S. Navy carrier optical landing device). ** Meatball is the light source of the FLOLS which the pilot uses for glideslope information in a carrier...LANDING DISPLAY FOV (Foot Lamberts) 1. Carrier Deck Runway Lighting 1.5 2. Carrier Runway Area 0.048 3. FLOLS Meatball 0.6 Figure 5 also shows the

Effect of Uncertainty on Deterministic Runway Scheduling

NASA Technical Reports Server (NTRS)

Gupta, Gautam; Malik, Waqar; Jung, Yoon C.

2012-01-01

Active runway scheduling involves scheduling departures for takeoffs and arrivals for runway crossing subject to numerous constraints. This paper evaluates the effect of uncertainty on a deterministic runway scheduler. The evaluation is done against a first-come- first-serve scheme. In particular, the sequence from a deterministic scheduler is frozen and the times adjusted to satisfy all separation criteria; this approach is tested against FCFS. The comparison is done for both system performance (throughput and system delay) and predictability, and varying levels of congestion are considered. The modeling of uncertainty is done in two ways: as equal uncertainty in availability at the runway as for all aircraft, and as increasing uncertainty for later aircraft. Results indicate that the deterministic approach consistently performs better than first-come-first-serve in both system performance and predictability.

The runway model of drug self-administration

PubMed Central

Ettenberg, Aaron

2009-01-01

Behavioral scientists have employed operant runways as a means of investigating the motivational impact of incentive stimuli for the better part of the past 100 years. In this task, the speed with which a trained animal traverses a long straight alley for positive incentive stimuli, like food or water, provides a reliable index of the subject’s motivation to seek those stimuli. The runway is therefore a particularly appropriate tool for investigating the drug-seeking behavior of animals working for drugs of abuse. The current review describes our laboratory’s work over the past twenty years developing and implementing an operant runway model of drug self-administration. Procedures are described that methodologically dissociate the antecedent motivational processes that induce an animal to seek a drug, from the positive reinforcing consequences of actually earning the drug. Additional work is reviewed on the use of the runway method as a means of modeling the factors that often result in a “relapse” of drug self-administration after a period of abstinence (i.e., a response reinstatement test), as are runway studies that revealed the presence of opposing positive and negative consequences of self-administered cocaine. This body of work suggests that the runway method has served as a powerful behavioral tool for the study of the behavioral and neurobiological basis of drug self-administration. PMID:19032964

SOUTHWEST SIDE AND SOUTHEAST FRONT, BUILDING 1932. OBSERVATION WINDOWS ARE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

SOUTHWEST SIDE AND SOUTHEAST FRONT, BUILDING 1932. OBSERVATION WINDOWS ARE BEHIND THE METAL GRATING. ENTRY HATCH IS ON NORTHWEST FACADE - Edwards Air Force Base, X-15 Engine Test Complex, Observation Bunker Types, Rogers Dry Lake, east of runway between North Base & South Base, Boron, Kern County, CA

SARDA: An Integrated Concept for Airport Surface Operations Management

NASA Technical Reports Server (NTRS)

Gupta, Gautam; Hoang, Ty; Jung, Yoon Chul

2013-01-01

The Spot and Runway Departure Advisor (SARDA) is an integrated decision support tool for airlines and air traffic control tower enabling surface collaborative decision making (CDM) and departure metering in order to enhance efficiency of surface operations at congested airports. The presentation describes the concept and architecture of the SARDA as a CDM tool, and the results from a human-in-the-loop simulation of the tool conducted in 2012 at the FutureFlight Central, the tower simulation facility. Also, presented is the current activities and future plan for SARDA development. The presentation was given at the meeting with the FAA senior advisor of the Surface Operations Office.

Cornering and wear characteristics of the Space Shuttle Orbiter nose-gear tire

NASA Technical Reports Server (NTRS)

Davis, Pamela A.; Stubbs, Sandy M.; Vogler, William A.

1989-01-01

Tests of the Space Shuttle Orbiter nose-gear tire have been completed at NASA Langley's Aircraft Landing Dynamics Facility. The purpose of these tests was to determine the cornering and wear characteristics of the Space Shuttle Orbiter nose-gear tire under realistic operating conditions. The tire was tested on a simulated Kennedy Space Center runway surface at speeds from 100 to 180 kts. The results of these tests defined the cornering characteristics which included side forces and associated side force friction coefficient over a range of yaw angles from 0 deg to 12 deg. Wear characteristics were defined by tire tread and cord wear over a yaw angle range of 0 deg to 4 deg under dry and wet runway conditions. Wear characteristics were also defined for a 15 kt crosswind landing with two blown right main-gear tires and nose-gear steering engaged.

Cornering and wear behavior of the Space Shuttle Orbiter main gear tire

NASA Technical Reports Server (NTRS)

Daugherty, Robert H.; Stubbs, Sandy M.

1987-01-01

One of the factors needed to describe the handling characteristics of the Space Shuttle Orbiter during the landing rollout is the response of the vehicle's tires to variations in load and yaw angle. An experimental investigation of the cornering characteristics of the Orbiter main gear tires was conducted at the NASA Langley Research Center Aircraft Landing Dynamics Facility. This investigation compliments earlier work done to define the Orbiter nose tire cornering characteristics. In the investigation, the effects of load and yaw angle were evaluated by measuring parameters such as side load and drag load, and obtaining measurements of aligning torque. Because the tire must operate on an extremely rough runway at the Shuttle Landing Facility at Kennedy Space Center (KSC), tests were also conducted to describe the wear behavior of the tire under various conditions on a simulated KSC runway surface. Mathematical models for both the cornering and the wear behavior are discussed.

The ASLOTS concept: An interactive, adaptive decision support concept for Final Approach Spacing of Aircraft (FASA). FAA-NASA Joint University Program

NASA Technical Reports Server (NTRS)

Simpson, Robert W.

1993-01-01

This presentation outlines a concept for an adaptive, interactive decision support system to assist controllers at a busy airport in achieving efficient use of multiple runways. The concept is being implemented as a computer code called FASA (Final Approach Spacing for Aircraft), and will be tested and demonstrated in ATCSIM, a high fidelity simulation of terminal area airspace and airport surface operations. Objectives are: (1) to provide automated cues to assist controllers in the sequencing and spacing of landing and takeoff aircraft; (2) to provide the controller with a limited ability to modify the sequence and spacings between aircraft, and to insert takeoffs and missed approach aircraft in the landing flows; (3) to increase spacing accuracy using more complex and precise separation criteria while reducing controller workload; and (4) achieve higher operational takeoff and landing rates on multiple runways in poor visibility.

Scheduler Design Criteria: Requirements and Considerations

NASA Technical Reports Server (NTRS)

Lee, Hanbong

2016-01-01

This presentation covers fundamental requirements and considerations for developing schedulers in airport operations. We first introduce performance and functional requirements for airport surface schedulers. Among various optimization problems in airport operations, we focus on airport surface scheduling problem, including runway and taxiway operations. We then describe a basic methodology for airport surface scheduling such as node-link network model and scheduling algorithms previously developed. Next, we explain how to design a mathematical formulation in more details, which consists of objectives, decision variables, and constraints. Lastly, we review other considerations, including optimization tools, computational performance, and performance metrics for evaluation.

14 CFR 151.87 - Lighting and electrical work: Standards.

Code of Federal Regulations, 2014 CFR

2014-01-01

... participate in the costs of runway lighting is eligible for the installing of an airport beacon, lighted wind... percent U.S. participation in the costs of high intensity runway edge lighting (or the allowable.... share of the cost of runway edge lighting is 50 percent of the cost of the lighting installed but not...

14 CFR 151.87 - Lighting and electrical work: Standards.

Code of Federal Regulations, 2012 CFR

2012-01-01

... participate in the costs of runway lighting is eligible for the installing of an airport beacon, lighted wind... percent U.S. participation in the costs of high intensity runway edge lighting (or the allowable.... share of the cost of runway edge lighting is 50 percent of the cost of the lighting installed but not...

14 CFR 151.87 - Lighting and electrical work: Standards.

Code of Federal Regulations, 2013 CFR

2013-01-01

... participate in the costs of runway lighting is eligible for the installing of an airport beacon, lighted wind... percent U.S. participation in the costs of high intensity runway edge lighting (or the allowable.... share of the cost of runway edge lighting is 50 percent of the cost of the lighting installed but not...

STS-33 Discovery, OV-103, MLG touches down on concrete runway 04 at EAFB

NASA Technical Reports Server (NTRS)

1989-01-01

STS-33 Discovery, Orbiter Vehicle (OV) 103, main landing gear (MLG) touches down on concrete runway 04 at Edwards Air Force Base (EAFB), California, at 16:31:02 pm Pacific Standard Time (PST). This view captures OV-103's profile (port side) as it glides down the runway.

Aircraft performance in slippery runway conditions : a simulation study of the accuracy and limitations of real-time runway friction estimation based on airplane onboard data.

DOT National Transportation Integrated Search

2015-04-01

Runway overrun accidents occurring during landings in slippery conditions continue to occur frequently worldwide. After a : number of specific landing overrun accidents in the U.S., the National Transportation Safety Board (NTSB) issued a safety : re...

77 FR 22378 - Noise Exposure Map Notice; Lafayette Regional Airport, Lafayette, LA

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-13

..., Existing and Future Condition Flight Tracks, Arrival and Departure--Runway 04L/R; Exhibit 4.3, Existing and Future Condition Flight Tracks, Arrival and Departure--Runway 11; Exhibit 4.4, Existing and Future Condition Flight Tracks, Arrival and Departure--Runway 22L/R; Exhibit 4.5, Existing and Future Condition...

14 CFR 151.87 - Lighting and electrical work: Standards.

Code of Federal Regulations, 2011 CFR

2011-01-01

... participate in the costs of runway lighting is eligible for the installing of an airport beacon, lighted wind... percent U.S. participation in the costs of high intensity runway edge lighting (or the allowable.... share of the cost of runway edge lighting is 50 percent of the cost of the lighting installed but not...

14 CFR 151.87 - Lighting and electrical work: Standards.

Code of Federal Regulations, 2010 CFR

2010-01-01

... participate in the costs of runway lighting is eligible for the installing of an airport beacon, lighted wind... percent U.S. participation in the costs of high intensity runway edge lighting (or the allowable.... share of the cost of runway edge lighting is 50 percent of the cost of the lighting installed but not...

A Simulation Study of Instrument Meteorological Condition Approaches to Dual Parallel Runways Spaced 3400 and 2500 Feet Apart Using Flight-Deck-Centered Technology

NASA Technical Reports Server (NTRS)

Waller, Marvin C.; Scanlon, Charles H.

1999-01-01

A number of our nations airports depend on closely spaced parallel runway operations to handle their normal traffic throughput when weather conditions are favorable. For safety these operations are curtailed in Instrument Meteorological Conditions (IMC) when the ceiling or visibility deteriorates and operations in many cases are limited to the equivalent of a single runway. Where parallel runway spacing is less than 2500 feet, capacity loss in IMC is on the order of 50 percent for these runways. Clearly, these capacity losses result in landing delays, inconveniences to the public, increased operational cost to the airlines, and general interruption of commerce. This document presents a description and the results of a fixed-base simulation study to evaluate an initial concept that includes a set of procedures for conducting safe flight in closely spaced parallel runway operations in IMC. Consideration of flight-deck information technology and displays to support the procedures is also included in the discussions. The procedures and supporting technology rely heavily on airborne capabilities operating in conjunction with the air traffic control system.

Speed Profiles for Deceleration Guidance During Rollout and Turnoff (ROTO)

NASA Technical Reports Server (NTRS)

Barker, L. Keith; Hankins, Walter W., III; Hueschen, Richard M.

1999-01-01

Two NASA goals are to enhance airport safety and to improve capacity in all weather conditions. This paper contributes to these goals by examining speed guidance profiles to aid a pilot in decelerating along the runway to an exit. A speed profile essentially tells the pilot what the airplane's speed should be as a function of where the airplane is on the runway. While it is important to get off the runway as soon as possible (when striving to minimize runway occupancy time), the deceleration along a speed profile should be constrained by passenger comfort. Several speed profiles are examined with respect to their maximum decelerations and times to reach exit speed. One profile varies speed linearly with distance; another has constant deceleration; and two related nonlinear profiles delay maximum deceleration (braking) to reduce time spent on the runway.

The effect of runway surface and braking on Shuttle Orbiter main gear tire wear

NASA Technical Reports Server (NTRS)

Daugherty, Robert H.; Stubbs, Sandy M.

1992-01-01

In 1988, a 1067 m long touchdown zone on each end of the Kennedy Space Center (KSC) Shuttle Landing Facility (SLF) was modified from its original heavy-broom finish with transverse grooves configuration to a longitudinal corduroy surface texture with no transverse grooves. The intent of this modification was to reduce the spin-up wear on the Orbiter main gear tires and provide for somewhat higher crosswind capabilities at that site. The modification worked well, so it was proposed that the remainder of the runway be modified as well to permit even higher crosswind landing capability. Tests were conducted at the NASA Langley Aircraft Landing Dynamics Facility (ALDF) to evaluate the merit of such a modification. This paper discusses the results of these tests, and explains why the proposed modification did not provide the expected improvement and thus was not implemented. Also, in an ongoing program to evaluate the origin of various tire wear phenomenon, a series of tests was conducted to evaluate the effect of braking on tire wear. Finally, a modified tire is discussed in terms of its wear performance under rollout and braking operations.

14 CFR 151.13 - Federal-aid Airport Program: Policy affecting landing aid requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

... (ALS). (2) In-runway lighting. (3) High intensity runway lighting. (4) Runway distance markers. For the purposes of this section “approach lighting system (ALS)” is a standard configuration of aeronautical... ALS and ILS, has been programmed by the FAA with funds then available therefor; (b) An extension of 3...

14 CFR 151.13 - Federal-aid Airport Program: Policy affecting landing aid requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... (ALS). (2) In-runway lighting. (3) High intensity runway lighting. (4) Runway distance markers. For the purposes of this section “approach lighting system (ALS)” is a standard configuration of aeronautical... ALS and ILS, has been programmed by the FAA with funds then available therefor; (b) An extension of 3...

14 CFR 151.13 - Federal-aid Airport Program: Policy affecting landing aid requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

... (ALS). (2) In-runway lighting. (3) High intensity runway lighting. (4) Runway distance markers. For the purposes of this section “approach lighting system (ALS)” is a standard configuration of aeronautical... ALS and ILS, has been programmed by the FAA with funds then available therefor; (b) An extension of 3...

14 CFR 151.13 - Federal-aid Airport Program: Policy affecting landing aid requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

... (ALS). (2) In-runway lighting. (3) High intensity runway lighting. (4) Runway distance markers. For the purposes of this section “approach lighting system (ALS)” is a standard configuration of aeronautical... ALS and ILS, has been programmed by the FAA with funds then available therefor; (b) An extension of 3...

14 CFR 151.13 - Federal-aid Airport Program: Policy affecting landing aid requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... (ALS). (2) In-runway lighting. (3) High intensity runway lighting. (4) Runway distance markers. For the purposes of this section “approach lighting system (ALS)” is a standard configuration of aeronautical... ALS and ILS, has been programmed by the FAA with funds then available therefor; (b) An extension of 3...

White Sands Space Harbor Area 1, Microwave Scanning Beam Landing ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

White Sands Space Harbor Area 1, Microwave Scanning Beam Landing Ground Stations, 1,500' to the south of the north end of Runway 17/35; 1,500' to the west of the east end of Runway 23/05; and 1,500' southwest of the northeast end of Runway 20/02., White Sands, Dona Ana County, NM

Wet runways. [aircraft landing and directional control

NASA Technical Reports Server (NTRS)

Horne, W. B.

1975-01-01

Aircraft stopping and directional control performance on wet runways is discussed. The major elements affecting tire/ground traction developed by jet transport aircraft are identified and described in terms of atmospheric, pavement, tire, aircraft system and pilot performance factors or parameters. Research results are summarized, and means for improving or restoring tire traction/aircraft performance on wet runways are discussed.

TRIZ Tool for Optimization of Airport Runway

NASA Astrophysics Data System (ADS)

Rao, K. Venkata; Selladurai, V.; Saravanan, R.

TRIZ tool is used for conceptual design and layout of the novel ascending and descending runway model for the effective utilization of short length airports. Handling bigger aircrafts at smaller airports become the necessity for economic consideration and for the benefit of vast airliners and the aspiring air travelers of the region. The authors’ proposal of ascending and descending runway would enable the operational need of wide body aircrafts such as Boeing 747 and Airbus A380-800. Negotiating take-off and landing of bigger aircrafts at less than 10000 feet runway is an optimization solution. This conceptual model and the theoretical design with its layout is dealt in this paper as Part - I. The computer-aided design and analysis using MATLAB with Simulink tool box to confirm the adequacy of the runway length for the bigger aircrafts at smaller airports is however dealt in subsequent papers.

Evaluation of Airborne Precision Spacing in a Human-in-the-Loop Experiment

NASA Technical Reports Server (NTRS)

Barmore, Bryan E.; Abbott, Terence S.; Capron, William R.

2005-01-01

A significant bottleneck in the current air traffic system occurs at the runway. Expanding airports and adding new runways will help solve this problem; however, this comes with significant costs: financially, politically and environmentally. A complementary solution is to safely increase the capacity of current runways. This can be achieved by precisely spacing aircraft at the runway threshold, with a resulting reduction in the spacing bu er required under today s operations. At NASA's Langley Research Center, the Airspace Systems program has been investigating airborne technologies and procedures that will assist the flight crew in achieving precise spacing behind another aircraft. A new spacing clearance allows the pilot to follow speed cues from a new on-board guidance system called Airborne Merging and Spacing for Terminal Arrivals (AMSTAR). AMSTAR receives Automatic Dependent Surveillance-Broadcast (ADS-B) reports from an assigned, leading aircraft and calculates the appropriate speed for the ownship to fly to achieve the desired spacing interval, time- or distance-based, at the runway threshold. Since the goal is overall system capacity, the speed guidance algorithm is designed to provide system-wide benefits and stability to a string of arriving aircraft. An experiment was recently performed at the NASA Langley Air Traffic Operations Laboratory (ATOL) to test the flexibility of Airborne Precision Spacing operations under a variety of operational conditions. These included several types of merge and approach geometries along with the complementary merging and in-trail operations. Twelve airline pilots and four controllers participated in this simulation. Performance and questionnaire data were collected from a total of eighty-four individual arrivals. The pilots were able to achieve precise spacing with a mean error of 0.5 seconds and a standard deviation of 4.7 seconds. No statistically significant di erences in spacing performance were found between in-trail and merging operations or among the three modeled airspaces. Questionnaire data showed general acceptance for both pilots and controllers. These results reinforce previous findings from full-mission simulation and flight evaluation of the in-trail operations. This paper reviews the results of this simulation in detail.

Polarimetric passive millimeter-wave sensing

NASA Astrophysics Data System (ADS)

Wikner, David A.; Samples, Greg

2001-08-01

The US Army Research Laboratory has developed a 93-Ghz Stokes radiometer that is currently being used to quantify the polarimetric signature of various objects and materials. Preliminary measurement using the radiometer have been made of various terrain types and objects, which have included an asphalt aircraft runway, a gravel road, water, grass a tank, and a truck. A description of the development of the radiometer, its performance, and some initial results are presented. These results are the first step in assessing the utility of polarimetric radiometry and specifically how missions can be enhanced using this information. The results show that polarimetric radiometry may be useful for eliminating water as a false target in the imagery. It is also shown that asphalt aircraft runways do have a polarimetric signature that is different than short dormant grass at a 3-deg glide slope angle.

78 FR 57674 - Order Limiting Operations at Newark Liberty International Airport

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-19

... season. This waiver applies only to EWR slots for the following days and local times: (1) March 30... runway 4L/22R. Runway 4L/22R will be open during that period with reduced runway length. Night and... five or more consecutive days. However, the FAA does not routinely grant general waivers to the usage...

STS-33 Discovery, OV-103, MLG touches down on EAFB concrete runway 04

NASA Technical Reports Server (NTRS)

1989-01-01

STS-33 Discovery, Orbiter Vehicle (OV) 103, main landing gear (MLG) touchdown is documented at Edwards Air Force Base (EAFB), California, on concrete runway 04. Views look forward from the space shuttle main engines (SSMEs) to the crew compartment as OV-103 glides down the runway. The landing occurred at 16:31:02 pm Pacific Standard Time (PST).

14 CFR Appendix A to Part 151 - Appendix A to Part 151

Code of Federal Regulations, 2011 CFR

2011-01-01

... zones at ends of eligible runways. (d) Approach lights (land for ALS eligible for 75 percent participation will be limited to an area 3200′ × 400′ for a Standard ALS and to an area 1700′ × 400′ for a short ALS located symmetrically about the runway centerline extended, beginning at the end of the runway...

14 CFR Appendix A to Part 151 - Appendix A to Part 151

Code of Federal Regulations, 2010 CFR

2010-01-01

... zones at ends of eligible runways. (d) Approach lights (land for ALS eligible for 75 percent participation will be limited to an area 3200′ × 400′ for a Standard ALS and to an area 1700′ × 400′ for a short ALS located symmetrically about the runway centerline extended, beginning at the end of the runway...

14 CFR Appendix A to Part 151 - Appendix A to Part 151

Code of Federal Regulations, 2014 CFR

2014-01-01

... zones at ends of eligible runways. (d) Approach lights (land for ALS eligible for 75 percent participation will be limited to an area 3200′ × 400′ for a Standard ALS and to an area 1700′ × 400′ for a short ALS located symmetrically about the runway centerline extended, beginning at the end of the runway...

14 CFR Appendix A to Part 151 - Appendix A to Part 151

Code of Federal Regulations, 2013 CFR

2013-01-01

... zones at ends of eligible runways. (d) Approach lights (land for ALS eligible for 75 percent participation will be limited to an area 3200′ × 400′ for a Standard ALS and to an area 1700′ × 400′ for a short ALS located symmetrically about the runway centerline extended, beginning at the end of the runway...

14 CFR Appendix A to Part 151 - Appendix A to Part 151

Code of Federal Regulations, 2012 CFR

2012-01-01

... zones at ends of eligible runways. (d) Approach lights (land for ALS eligible for 75 percent participation will be limited to an area 3200′ × 400′ for a Standard ALS and to an area 1700′ × 400′ for a short ALS located symmetrically about the runway centerline extended, beginning at the end of the runway...

KSC-04PD-0934

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. This aerial photo of the runway at the KSC Shuttle Landing Facility looks north. Longer and wider than most commercial runways, it is 15,000 feet long, with 1,000-foot paved overruns on each end, and 300 feet wide, with 50-foot asphalt shoulders. The runway is used by military and civilian cargo carriers, astronauts T-38 trainers, Shuttle Training Aircraft and helicopters, as well as the Space Shuttle. On the lower right is the parking apron with the orbiter mate/demate tower and the tow-way stretching from the runway to the lower right. Farther north is a grassy area where the new control tower is located.

KSC-04pd0934

NASA Image and Video Library

2004-03-31

KENNEDY SPACE CENTER, FLA. - This aerial photo of the runway at the KSC Shuttle Landing Facility looks north. Longer and wider than most commercial runways, it is 15,000 feet long, with 1,000-foot paved overruns on each end, and 300 feet wide, with 50-foot asphalt shoulders. The runway is used by military and civilian cargo carriers, astronauts’ T-38 trainers, Shuttle Training Aircraft and helicopters, as well as the Space Shuttle. On the lower right is the parking apron with the orbiter mate/demate tower and the tow-way stretching from the runway to the lower right. Farther north is a grassy area where the new control tower is located.

NASA Runway Incursion Prevention System (RIPS) Dallas-Fort Worth Demonstration Performance Analysis

NASA Technical Reports Server (NTRS)

Cassell, Rick; Evers, Carl; Esche, Jeff; Sleep, Benjamin; Jones, Denise R. (Technical Monitor)

2002-01-01

NASA's Aviation Safety Program Synthetic Vision System project conducted a Runway Incursion Prevention System (RIPS) flight test at the Dallas-Fort Worth International Airport in October 2000. The RIPS research system includes advanced displays, airport surveillance system, data links, positioning system, and alerting algorithms to provide pilots with enhanced situational awareness, supplemental guidance cues, a real-time display of traffic information, and warnings of runway incursions. This report describes the aircraft and ground based runway incursion alerting systems and traffic positioning systems (Automatic Dependent Surveillance - Broadcast (ADS-B) and Traffic Information Service - Broadcast (TIS-B)). A performance analysis of these systems is also presented.

Wake Encounter Analysis for a Closely Spaced Parallel Runway Paired Approach Simulation

NASA Technical Reports Server (NTRS)

Mckissick,Burnell T.; Rico-Cusi, Fernando J.; Murdoch, Jennifer; Oseguera-Lohr, Rosa M.; Stough, Harry P, III; O'Connor, Cornelius J.; Syed, Hazari I.

2009-01-01

A Monte Carlo simulation of simultaneous approaches performed by two transport category aircraft from the final approach fix to a pair of closely spaced parallel runways was conducted to explore the aft boundary of the safe zone in which separation assurance and wake avoidance are provided. The simulation included variations in runway centerline separation, initial longitudinal spacing of the aircraft, crosswind speed, and aircraft speed during the approach. The data from the simulation showed that the majority of the wake encounters occurred near or over the runway and the aft boundaries of the safe zones were identified for all simulation conditions.

Low-velocity impact tests on fibrous composite sandwich structures

NASA Technical Reports Server (NTRS)

Sharma, A. V.

1981-01-01

The effect of low-velocity projectile impact on the load-carrying ability of the composite sandwich structural components is investigated experimentally, the impact simulating the damage caused by runway debris and the accidental dropping of hand tools during servicing on secondary aircraft structures made with composites. The sandwich-type beam specimens were fabricated with graphite/epoxy face sheets, aluminum honeycomb core, and a steel (back) plate. A four-point beam-loading apparatus was used, and the ultimate strength, ultimate strain, and residual strength of the composites were determined. A faired curve is presented indicating the lower bound of the failure threshold for each of the laminate configurations tested in compression and tension as a function of the projectile impact energy. It is shown that strength degradation due to impact is dependent on the laminate configuration and the fiber/matrix combination. The laminates having more angle plies near the impact surface and unidirectional plies elsewhere seem to show extensive interply and intraply fiber delaminations at failure relative to the laminates with a cross-ply on the impact surface.

Influence of Surface Properties and Impact Conditions on Insect Residue Adhesion

NASA Technical Reports Server (NTRS)

Wohl, Christopher J.; Doss, Jereme R.; Shanahan, Michelle H.; Smith, Joseph G., Jr.; Penner, Ronald K.; Connell, John W.; Siochi, Emilie J.

2015-01-01

Airflow over airfoils used on current commercial aircraft transitions from laminar to turbulent at relatively low chord positions. As a result, drag increases, requiring more thrust to maintain flight. An airfoil with increased laminar flow would experience reduced drag and a lower fuel burn rate. One of the objectives of NASA's Environmentally Responsible Aviation project is to identify and demonstrate technologies that will enable more environmentally friendly commercial aircraft. While more aerodynamically efficient airfoil shapes can be designed, surface contamination from ice, dirt, pollen, runway debris, and insect residue can degrade performance.

Thermal conductance of and heat generation in tire-pavement interface and effect on aircraft braking

NASA Technical Reports Server (NTRS)

Miller, C. D.

1976-01-01

A finite-difference analysis was performed on temperature records obtained from a free rolling automotive tire and from pavement surface. A high thermal contact conductance between tire and asphalt was found on a statistical basis. Average slip due to squirming between tire and asphalt was about 1.5 mm. Consequent friction heat was estimated as 64 percent of total power absorbed by bias-ply, belted tire. Extrapolation of results to aircraft tire indicates potential braking improvement by even moderate increase of heat absorbing capacity of runway surface.

Fuel Consumption and Emissions from Airport Taxi Operations

NASA Technical Reports Server (NTRS)

Jung, Yoon

2010-01-01

Developed a method to calculate fuel consumption and emissions of phases of taxi operations. Results at DFW showed that up to 18% of fuel can be saved by eliminating stop-and-go situations. Developed an energy efficient and environmentally friendly surface concept: Spot and Runway Departure Advisory (SARDA) tool. The SARDA tool has been identified as a potential candidate for a technology transfer to the FAA.

Graphical User Interface Development and Design to Support Airport Runway Configuration Management

NASA Technical Reports Server (NTRS)

Jones, Debra G.; Lenox, Michelle; Onal, Emrah; Latorella, Kara A.; Lohr, Gary W.; Le Vie, Lisa

2015-01-01

The objective of this effort was to develop a graphical user interface (GUI) for the National Aeronautics and Space Administration's (NASA) System Oriented Runway Management (SORM) decision support tool to support runway management. This tool is expected to be used by traffic flow managers and supervisors in the Airport Traffic Control Tower (ATCT) and Terminal Radar Approach Control (TRACON) facilities.

STS-40 Columbia, OV-102, lands on concrete runway 22 at EAFB, California

NASA Technical Reports Server (NTRS)

1991-01-01

STS-40 Columbia's, Orbiter Vehicle (OV) 102's, main landing gear (MLG) touches down on concrete runway 22 at Edwards Air Force Base (EAFB), California at 8:29:11 am (Pacific Daylight Time (PDT)). OV-102's port side is captured in this profile view as its nose landing gear (NLG) glides above the runway before touch down and wheel stop.

STS-40 Columbia, OV-102, lands on concrete runway 22 at EAFB, California

NASA Technical Reports Server (NTRS)

1991-01-01

STS-40 Columbia's, Orbiter Vehicle (OV) 102's, main landing gear (MLG) touches down on concrete runway 22 at Edwards Air Force Base (EAFB), California at 8:29:11 am (Pacific Daylight Time (PDT)). OV-102's starboard side is captured in this profile view as its nose landing gear (NLG) glides above the runway before touch down and wheel stop.

Effect of Surface Traffic Count on Taxi Time at Dallas-Fort Worth (DFW) International Airport

NASA Technical Reports Server (NTRS)

Kistler, Matthew Stephen; Gupta, Gautam

2008-01-01

As the amount of air traffic increases over the years, most airports simply do not have the means of expanding to handle the intensified traffic on the surface that will ensue. Precise surveillance equipment and automation concepts, as well as advanced surface traffic algorithms are being developed to improve airport efficiency. These surface algorithms require inputs unique to each airport to ensure maximum efficiency, and minimal taxi delay. This study analyzes surface traffic at Dallas-Fort Worth International Airport (DFW) to determine the effect of the number of aircraft on the surface and the amount of stop and go situations they experience to the amount of additional taxi time encountered. If the surface capacity of an airport is known, minimal delay can be accomplished by limiting the number of taxiing aircraft to that capacity. This concept is related to highways, where traffic flow drastically decreases as more cars occupy the road. An attempt to minimize this effect on highways is seen with the use of metering lights at freeway on-ramps. Since the surface traffic at airports is highly regulated, and aircraft are less mobile on the ground, limiting the surface count to a certain number can greatly reduce the amount of additional taxi time encountered, as well as reduce hazardous emissions. This study will also find the regions of an airport that encounter the most additional taxi time when the number of aircraft in that area is increased. This could help surface traffic algorithms avoid congesting that area, or re-route aircraft to different runways when that area reaches its capacity. The relationship between the amount of stop and go situations an aircraft encounters and their effect on the taxi time of that aircraft will also be investigated. This will help to determine the effect of holding an aircraft on the taxiway as opposed to re-routing it. The lesser of the two should be used when developing surface traffic algorithms to further minimize the delay encountered. The fields investigated in this study include taxi time, the number of aircraft on the surface, the number of stop and go situations, and the time stopped for each aircraft. Taxi time is defined as spot to runway for departures, and runway to spot for arrivals. It does not include ramp area taxi time because the ramp area is controlled differently, and surface traffic schedulers do not currently incorporate them. Taxi time is found by finding the difference between take-off time (OFF) and spot crossing time for departures, and spot crossing time and landing time (ON) for arrivals. All surface data was either found directly using the Surface Operations Data Analysis and Adaptation (SODAA), a tool to analyze the Surface Management System (SMS) generated log files, or indirectly from SODAA using Matlab to derive values from SODAA data. The number of aircraft on the surface is found by looping through the ON times, OFF times, and spot times for each aircraft during a particular day. For each departure aircraft, surface counts are taken at its spot crossing and OFF time. The average of these two is used as the surface count for that aircraft. For arrivals, surface counts are taken at its ON time and its spot crossing time. The average of these two is used.

KSC-04PD-0935

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. This aerial photo shows the runway at the KSC Shuttle Landing Facility at left. Longer and wider than most commercial runways, it is 15,000 feet long, with 1,000-foot paved overruns on each end, and 300 feet wide, with 50-foot asphalt shoulders. The runway is used by military and civilian cargo carriers, astronauts T-38 trainers, Shuttle Training Aircraft and helicopters, as well as the Space Shuttle. In the foreground is the parking apron with the orbiter mate/demate tower, the hangar and other storage facilities, and the tow-way stretching from the runway to the lower right. Farther north is a grassy area where the new control tower is located.

KSC-04PD-0936

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. This aerial photo shows the runway at the KSC Shuttle Landing Facility extending left to upper right. Longer and wider than most commercial runways, it is 15,000 feet long, with 1,000-foot paved overruns on each end, and 300 feet wide, with 50-foot asphalt shoulders. The runway is used by military and civilian cargo carriers, astronauts T-38 trainers, Shuttle Training Aircraft and helicopters, as well as the Space Shuttle. In the foreground is the parking apron with the orbiter mate/demate tower, the hangar and other storage facilities, and the tow-way stretching from the runway to the lower center. In the upper right is a grassy area where the new control tower is located.

KSC-04pd0935

NASA Image and Video Library

2004-03-31

KENNEDY SPACE CENTER, FLA. - This aerial photo shows the runway at the KSC Shuttle Landing Facility at left. Longer and wider than most commercial runways, it is 15,000 feet long, with 1,000-foot paved overruns on each end, and 300 feet wide, with 50-foot asphalt shoulders. The runway is used by military and civilian cargo carriers, astronauts’ T-38 trainers, Shuttle Training Aircraft and helicopters, as well as the Space Shuttle. In the foreground is the parking apron with the orbiter mate/demate tower, the hangar and other storage facilities, and the tow-way stretching from the runway to the lower right. Farther north is a grassy area where the new control tower is located.

KSC-04pd0936

NASA Image and Video Library

2004-03-31

KENNEDY SPACE CENTER, FLA. - This aerial photo shows the runway at the KSC Shuttle Landing Facility extending left to upper right. Longer and wider than most commercial runways, it is 15,000 feet long, with 1,000-foot paved overruns on each end, and 300 feet wide, with 50-foot asphalt shoulders. The runway is used by military and civilian cargo carriers, astronauts’ T-38 trainers, Shuttle Training Aircraft and helicopters, as well as the Space Shuttle. In the foreground is the parking apron with the orbiter mate/demate tower, the hangar and other storage facilities, and the tow-way stretching from the runway to the lower center. In the upper right is a grassy area where the new control tower is located.

Human Factors Lessons Learned from Flight Testing Wingless Lifting Body Vehicles

NASA Technical Reports Server (NTRS)

Merlin, Peter William

2014-01-01

Since the 1960s, NASA, the Air Force, and now private industry have attempted to develop an operational human crewed reusable spacecraft with a wingless, lifting body configuration. This type of vehicle offers increased mission flexibility and greater reentry cross range than capsule type craft, and is particularly attractive due to the capability to land on a runway. That capability, however, adds complexity to the human factors engineering requirements of developing such aircraft.

Wind Advisory System

NASA Technical Reports Server (NTRS)

Curto, Paul A. (Inventor); Brown, Gerald E. (Inventor); Zysko, Jan A. (Inventor)

2001-01-01

The present invention is a two-part wind advisory system comprising a ground station at an airfield and an airborne unit placed inside an aircraft. The ground station monitors wind conditions (wind speed, wind direction, and wind gust) at the airfield and transmits the wind conditions and an airfield ID to the airborne unit. The airborne unit identifies the airfield by comparing the received airfield ID with airfield IDs stored in a database. The airborne unit also calculates the headwind and crosswind for each runway in both directions at the airfield using the received wind conditions and runway information stored in the database. The airborne unit then determines a recommended runway for takeoff and landing operations of the aircraft based on th runway having the greatest headwind value and displays the airfield ID, wind conditions, and recommended runway to the pilot. Another embodiment of the present invention includes a wireless internet based airborne unit in which the airborne unit can receive the wind conditions from the ground station over the internet.

Evaluation of Scheduling Methods for Multiple Runways

NASA Technical Reports Server (NTRS)

Bolender, Michael A.; Slater, G. L.

1996-01-01

Several scheduling strategies are analyzed in order to determine the most efficient means of scheduling aircraft when multiple runways are operational and the airport is operating at different utilization rates. The study compares simulation data for two and three runway scenarios to results from queuing theory for an M/D/n queue. The direction taken, however, is not to do a steady-state, or equilibrium, analysis since this is not the case during a rush period at a typical airport. Instead, a transient analysis of the delay per aircraft is performed. It is shown that the scheduling strategy that reduces the delay depends upon the density of the arrival traffic. For light traffic, scheduling aircraft to their preferred runways is sufficient; however, as the arrival rate increases, it becomes more important to separate traffic by weight class. Significant delay reduction is realized when aircraft that belong to the heavy and small weight classes are sent to separate runways with large aircraft put into the 'best' landing slot.

The Fight Deck Perspective of the NASA Langley AILS Concept

NASA Technical Reports Server (NTRS)

Rine, Laura L.; Abbott, Terence S.; Lohr, Gary W.; Elliott, Dawn M.; Waller, Marvin C.; Perry, R. Brad

2000-01-01

Many US airports depend on parallel runway operations to meet the growing demand for day to day operations. In the current airspace system, Instrument Meteorological Conditions (IMC) reduce the capacity of close parallel runway operations; that is, runways spaced closer than 4300 ft. These capacity losses can result in landing delays causing inconveniences to the traveling public, interruptions in commerce, and increased operating costs to the airlines. This document presents the flight deck perspective component of the Airborne Information for Lateral Spacing (AILS) approaches to close parallel runways in IMC. It represents the ideas the NASA Langley Research Center (LaRC) AILS Development Team envisions to integrate a number of components and procedures into a workable system for conducting close parallel runway approaches. An initial documentation of the aspects of this concept was sponsored by LaRC and completed in 1996. Since that time a number of the aspects have evolved to a more mature state. This paper is an update of the earlier documentation.

Effects of various runway lighting parameters upon the relation between runway visual range and visual range of centerline and edge lights in fog

NASA Technical Reports Server (NTRS)

Haines, R. F.

1973-01-01

Thirty six students and 54 commercial airline pilots were tested in the fog chamber to determine the effect of runway edge and centerline light intensity and spacing, fog density, ambient luminance level, and lateral and vertical offset distance of the subject from the runway's centerline upon horizontal visual range. These data were obtained to evaluate the adequacy of a balanced lighting system to provide maximum visual range in fog viewing both centerline and runway edge lights. The daytime system was compared against two other candidate lighting systems; the nighttime system was compared against other candidate lighting systems. The second objective was to determine if visual range is affected by lights between the subject and the farthestmost light visible through the fog. The third objective was to determine if college student subjects differ from commercial airline pilots in their horizontal visual range through fog. Two studies were conducted.

Near-field commercial aircraft contribution to nitrogen oxides by engine, aircraft type, and airline by individual plume sampling.

PubMed

Carslaw, David C; Ropkins, Karl; Laxen, Duncan; Moorcroft, Stephen; Marner, Ben; Williams, Martin L

2008-03-15

Nitrogen oxides (NOx) concentrations were measured in individual plumes from aircraft departing on the northern runway at Heathrow Airport in west London. Over a period of four weeks 5618 individual plumes were sampled by a chemiluminescence monitor located 180 m from the runway. Results were processed and matched with detailed aircraft movement and aircraft engine data using chromatographic techniques. Peak concentrations associated with 29 commonly used engines were calculated and found to have a good relationship with N0x emissions taken from the International Civil Aviation Organization (ICAO) databank. However, it is found that engines with higher reported NOx emissions result in proportionately lower NOx concentrations than engines with lower emissions. We show that it is likely that aircraft operational factors such as takeoff weight and aircraftthrust setting have a measurable and important effect on concentrations of N0x. For example, NOx concentrations can differ by up to 41% for aircraft using the same airframe and engine type, while those due to the same engine type in different airframes can differ by 28%. These differences are as great as, if not greater than, the reported differences in NOx emissions between different engine manufacturers for engines used on the same airframe.

KSC-04PD-0933

NASA Technical Reports Server (NTRS)

2004-01-01

KENNEDY SPACE CENTER, FLA. This aerial photo of the runway at the KSC Shuttle Landing Facility looks north. Longer and wider than most commercial runways, it is 15,000 feet long, with 1,000-foot paved overruns on each end, and 300 feet wide, with 50-foot asphalt shoulders. The runway is used by military and civilian cargo carriers, astronauts T-38 trainers, Shuttle Training Aircraft and helicopters, as well as the Space Shuttle.

KSC-04pd0933

NASA Image and Video Library

2004-03-31

KENNEDY SPACE CENTER, FLA. - This aerial photo of the runway at the KSC Shuttle Landing Facility looks north. Longer and wider than most commercial runways, it is 15,000 feet long, with 1,000-foot paved overruns on each end, and 300 feet wide, with 50-foot asphalt shoulders. The runway is used by military and civilian cargo carriers, astronauts’ T-38 trainers, Shuttle Training Aircraft and helicopters, as well as the Space Shuttle.

STS-26 Discovery, OV-103, touches down on dry lakebed runway 17 at EAFB

NASA Technical Reports Server (NTRS)

1988-01-01

STS-26 Discovery, Orbiter Vehicle (OV) 103, main landing gear (MLG) touches down on dry lakebed runway 17 at Edwards Air Force Base (EAFB), California. A small cloud of dust forms behind MLG as OV-103 begins to slow down as it passes a series of runway lights. EAFB and Dryden Flight Research Facility (DFRF) buildings and hangars appear in the background.

Landing Characteristics of a Lenticular-Shaped Reentry Vehicle

NASA Technical Reports Server (NTRS)

Blanchard, Ulysse J.

1961-01-01

An experimental investigation was made of the landing characteristics of a 1/9-scale dynamic model of a lenticular-shaped reentry vehicle having extendible tail panels for control after reentry and for landing control (flare-out). The landing tests were made by catapulting a free model onto a hard-surface runway and onto water. A "belly-landing" technique in which the vehicle was caused to skid and rock on its curved undersurface (heat shield), converting sinking speed into angular energy, was investigated on a hard-surface runway. Landings were made in calm water and in waves both with and without auxiliary landing devices. Landing motions and acceleration data were obtained over a range of landing attitudes and initial sinking speeds during hard-surface landings and for several wave conditions during water landings. A few vertical landings (parachute letdown) were made in calm water. The hard-surface landing characteristics were good. Maximum landing accelerations on a hard surface were 5g and 18 radians per sq second over a range of landing conditions. Horizontal landings on water resulted in large violent rebounds and some diving in waves. Extreme attitude changes during rebound at initial impact made the attitude of subsequent impact random. Maximum accelerations for water landings were approximately 21g and 145 radians per sq second in waves 7 feet high. Various auxiliary water-landing devices produced no practical improvement in behavior. Reduction of horizontal speed and positive control of impact attitude did improve performance in calm water. During vertical landings in calm water maximum accelerations of 15g and 110 radians per sq second were measured for a contact attitude of -45 deg and a vertical velocity of 70 feet per second.

Design Considerations for a New Terminal Area Arrival Scheduler

NASA Technical Reports Server (NTRS)

Thipphavong, Jane; Mulfinger, Daniel

2010-01-01

Design of a terminal area arrival scheduler depends on the interrelationship between throughput, delay and controller intervention. The main contribution of this paper is an analysis of the above interdependence for several stochastic behaviors of expected system performance distributions in the aircraft s time of arrival at the meter fix and runway. Results of this analysis serve to guide the scheduler design choices for key control variables. Two types of variables are analyzed, separation buffers and terminal delay margins. The choice for these decision variables was tested using sensitivity analysis. Analysis suggests that it is best to set the separation buffer at the meter fix to its minimum and adjust the runway buffer to attain the desired system performance. Delay margin was found to have the least effect. These results help characterize the variables most influential in the scheduling operations of terminal area arrivals.

STS-34 Atlantis, OV-104, touches down on runway 23 at EAFB, California

NASA Technical Reports Server (NTRS)

1989-01-01

STS-34 Atlantis, Orbiter Vehicle (OV) 104, main landing gear (MLG) touches down on Runway 23 dry lake bed at Edwards Air Force Base (EAFB), California. The nose landing gear rides above runway before touchdown as the MLG wheels produce a cloud of dust. OV-104's port side profile is captured as it glides by at a speed of approximately 195 knots (224 miles per hour).

STS-26 Discovery, OV-103, touches down on dry lakebed runway 17 at EAFB

NASA Technical Reports Server (NTRS)

1988-01-01

STS-26 Discovery, Orbiter Vehicle (OV) 103, main landing gear (MLG) touches down on dry lakebed runway 17 at Edwards Air Force Base (EAFB), California. A cloud of dust forms behind MLG as OV-103 begins to slow down as it passes portable runway lights. Taken from the rear of the orbiter, view shows the space shuttle main engines (SSMEs) and the speedbrake/rudder deployed on tail section.

Joint Winter Runway Friction Program Accomplishments

NASA Technical Reports Server (NTRS)

Yager, Thomas J.; Wambold, James C.; Henry, John J.; Andresen, Arild; Bastian, Matthew

2002-01-01

The major program objectives are: (1) harmonize ground vehicle friction measurements to report consistent friction value or index for similar contaminated runway conditions, for example, compacted snow, and (2) establish reliable correlation between ground vehicle friction measurements and aircraft braking performance. Accomplishing these objectives would give airport operators better procedures for evaluating runway friction and maintaining acceptable operating conditions, providing pilots information to base go/no go decisions, and would contribute to reducing traction-related aircraft accidents.

Runway Incursion Prevention System: Demonstration and Testing at the Dallas/Fort Worth International Airport

NASA Technical Reports Server (NTRS)

Jones, Denise R.; Quach, Cuong C.; Young, Steven D.

2007-01-01

A Runway Incursion Prevention System (RIPS) was tested at the Dallas-Ft. Worth International Airport (DFW) in October 2000. The system integrated airborne and ground components to provide both pilots and controllers with enhanced situational awareness, supplemental guidance cues, a real-time display of traffic information, and warning of runway incursions in order to prevent runway incidents while also improving operational capability. A series of test runs was conducted using NASA s Boeing 757 research aircraft and a test van equipped to emulate an incurring aircraft. The system was also demonstrated to over 100 visitors from the aviation community. This paper gives an overview of the RIPS, DFW flight test activities, and quantitative and qualitative results of the testing.

Monitoring Aircraft Motion at Airports by LIDAR

NASA Astrophysics Data System (ADS)

Toth, C.; Jozkow, G.; Koppanyi, Z.; Young, S.; Grejner-Brzezinska, D.

2016-06-01

Improving sensor performance, combined with better affordability, provides better object space observability, resulting in new applications. Remote sensing systems are primarily concerned with acquiring data of the static components of our environment, such as the topographic surface of the earth, transportation infrastructure, city models, etc. Observing the dynamic component of the object space is still rather rare in the geospatial application field; vehicle extraction and traffic flow monitoring are a few examples of using remote sensing to detect and model moving objects. Deploying a network of inexpensive LiDAR sensors along taxiways and runways can provide both geometrically and temporally rich geospatial data that aircraft body can be extracted from the point cloud, and then, based on consecutive point clouds motion parameters can be estimated. Acquiring accurate aircraft trajectory data is essential to improve aviation safety at airports. This paper reports about the initial experiences obtained by using a network of four Velodyne VLP- 16 sensors to acquire data along a runway segment.

Development and Evaluation of New Calibration Site, Tyndall AFB, for Continuous Friction Measurement Equipment

DTIC Science & Technology

2016-02-01

color images. The Air Force Civil Engineering Center (AFCEC) has been measuring military runway pavement friction and texture conditions around the...world for many years. In recent years, the friction measurements have been collected using seven GripTester (GT) trailers, and pavement texture...with several conclusions and recommendations are given as well as a list of appropriate references. pavement friction, calibration, pavement surface U U

Input-Output Modeling and Control of the Departure Process of Congested Airports

NASA Technical Reports Server (NTRS)

Pujet, Nicolas; Delcaire, Bertrand; Feron, Eric

2003-01-01

A simple queueing model of busy airport departure operations is proposed. This model is calibrated and validated using available runway configuration and traffic data. The model is then used to evaluate preliminary control schemes aimed at alleviating departure traffic congestion on the airport surface. The potential impact of these control strategies on direct operating costs, environmental costs and overall delay is quantified and discussed.

26 x 6.6 radial-belted aircraft tire performance

NASA Technical Reports Server (NTRS)

Davis, Pamela A.; Martinson, Veloria J.; Yager, Thomas J.; Stubbs, Sandy M.

1991-01-01

Preliminary results from testing of 26 x 6.6 radial-belted and bias-ply aircraft tires at NASA Langley's Aircraft Landing Dynamics Facility (ALDF) are reviewed. The 26 x 6.6 tire size evaluation includes cornering performance tests throughout the aircraft ground operational speed range for both dry and wet runway surfaces. Static test results to define 26 x 6.6 tire vertical stiffness properties are also presented and discussed.

A LiDAR application for the study of taxiway surface evenness and slope

NASA Astrophysics Data System (ADS)

Barbarella, M.; De Blasiis, M. R.; Fiani, M.; Santoni, M.

2014-05-01

Pavement roughness evaluation of airport runways/taxiways and scheduling of maintenance operations should be done according to well-defined procedures. Survey of geometric features of airport pavements is performed to verify the flow of water from the surface and to assure a level of roughness that allows the airplane to maneuver in the safest and most comfortable conditions. In particular the evaluation of longitudinal and transversal evenness of the runway and taxiway is carried out through topographic survey. The tachymetric survey has been carried out according to traditional topographic technique, which allows the evaluation of geometric position of isolated points with very high accuracy, but it is not very productive. Moreover it returns the pavement surface model through only few measured points. An alternative survey method, characterized by a good accuracy, high speed of acquisition and very high surveyed point density, is Terrestrial Laser Scanning (TLS), in static mode. In this paper we describe our experience aimed to validate the use of time-of-flight (TOF) TLS, based on a survey on a 200 m length segment of an international airport taxiway. From the acquired data we extracted the parameters of interest, especially the slope, and compared them with the values obtained from the traditional topographic survey. We also developed a proprietary software package to evaluate the slope and to analyze the statistical data. The software allows users to manage the flow of a semi-automatic calculation.

Interval Management with Spacing to Parallel Dependent Runways (IMSPIDR) Experiment and Results

NASA Technical Reports Server (NTRS)

Baxley, Brian T.; Swieringa, Kurt A.; Capron, William R.

2012-01-01

An area in aviation operations that may offer an increase in efficiency is the use of continuous descent arrivals (CDA), especially during dependent parallel runway operations. However, variations in aircraft descent angle and speed can cause inaccuracies in estimated time of arrival calculations, requiring an increase in the size of the buffer between aircraft. This in turn reduces airport throughput and limits the use of CDAs during high-density operations, particularly to dependent parallel runways. The Interval Management with Spacing to Parallel Dependent Runways (IMSPiDR) concept uses a trajectory-based spacing tool onboard the aircraft to achieve by the runway an air traffic control assigned spacing interval behind the previous aircraft. This paper describes the first ever experiment and results of this concept at NASA Langley. Pilots flew CDAs to the Dallas Fort-Worth airport using airspeed calculations from the spacing tool to achieve either a Required Time of Arrival (RTA) or Interval Management (IM) spacing interval at the runway threshold. Results indicate flight crews were able to land aircraft on the runway with a mean of 2 seconds and less than 4 seconds standard deviation of the air traffic control assigned time, even in the presence of forecast wind error and large time delay. Statistically significant differences in delivery precision and number of speed changes as a function of stream position were observed, however, there was no trend to the difference and the error did not increase during the operation. Two areas the flight crew indicated as not acceptable included the additional number of speed changes required during the wind shear event, and issuing an IM clearance via data link while at low altitude. A number of refinements and future spacing algorithm capabilities were also identified.

Attentional limitations with Head-Up Displays

NASA Technical Reports Server (NTRS)

Mccann, Robert S.; Foyle, David C.; Johnston, James C.

1993-01-01

Recent models of visual information processing suggest that visual attention can be focussed on either Head-Up Displays (HUD) or on the world beyond them, but not on both simultaneously. This hypothesis was tested in a part-task simulation in which subjects viewed a simulated approach to a runway with a HUD superimposed. An alphanumeric cue ('IFR' or 'VFR') appeared on either the HUD or the runway and was followed by two sets of three geometric forms; one set on the HUD and one set on the runway. Each set contained one potential target, either a stop sign or a diamond. If the cue spelled 'IFR', subjects made a speeded response based on the identity of the HUD target; if the cue spelled 'VFR', subjects made a speeded response based on the identity of the runway target. Regardless of cue location (HUD or Runway), responses were faster when the cue and the relevant target were part of the same perceptual group (i.e., both on the HUD or both on the runway) than when they were part of different perceptual groups. These results, as well as others, suggest that attentional constraints place severe limits on the ability of pilots to process HUD-referenced information and world-referenced information simultaneously. In addition, they provide direct evidence that transitioning from processing HUD information to processing world information requires an attention shift. Implications for HUD design are considered.

Terminal Area Procedures for Paired Runways

NASA Technical Reports Server (NTRS)

Lozito, Sandy

2011-01-01

Parallel Runway operations have been found to increase capacity within the National Airspace (NAS) however, poor visibility conditions reduce this capacity [1]. Much research has been conducted to examine the concepts and procedures related to parallel runways however, there has been no investigation of the procedures associated with the strategic and tactical pairing of aircraft for these operations. This study developed and examined the pilot and controller procedures and information requirements for creating aircraft pairs for parallel runway operations. The goal was to achieve aircraft pairing with a temporal separation of 15s(+/- 10s error) at a coupling point that is about 12 nmi from the runway threshold. Two variables were explored for the pilot participants: Two levels of flight deck automation (current-day flight deck automation, and a prototype future automation) as well as two flight deck displays that assisted in pilot conformance monitoring. The controllers were also provided with automation to help create and maintain aircraft pairs. Data showed that the operations in this study were found to be acceptable and safe. Workload when using the pairing procedures and tools was generally low for both controllers and pilots, and situation awareness (SA) was typically moderate to high. There were some differences based upon the display and automation conditions for the pilots. Future research should consider the refinement of the concepts and tools for pilot and controller displays and automation for parallel runway concepts.

Friction and wear characteristics of wire-brush skids

NASA Technical Reports Server (NTRS)

Dreher, R. C.

1979-01-01

The testing technique consisted of towing the skids with a ground test vehicle over asphalt and concrete surfaces at ground speeds up to 80 km/hr (50 mph) and bearing pressures up to 689 kPa (100 psi) over sliding distances up to 1585 m (5200 ft). Results indicate that the friction coefficient developed by wire brush skids is essentially independent of ground speed, is slightly increased with increasing bearing pressure, is noticeably affected by surface texture, and is not degraded by surface wetness. Skid wear is shown to increase with increasing bearing pressure and with increasing ground speed and is dependent on the nature of the surface. Runway surface damage caused by the skids was in the form of an abrasive scrubbing action rather than physical damage.

Emergency Flight Control Using Computer-Controlled Thrust

NASA Technical Reports Server (NTRS)

Burcham, Frank W., Jr.; Fullerton, C. Gordon; Stewart, James F.; Gilyard, Glenn B.; Conley, Joseph A.

1995-01-01

Propulsion Controlled Aircraft (PCA) systems are digital electronic control systems undergoing development to provide limited maneuvering ability through variations of individual engine thrusts in multiple-engine airplanes. Provide landing capability when control surfaces inoperable. Incorporated on existing and future airplanes that include digital engine controls, digital flight controls, and digital data buses, adding no weight for additional hardware to airplane. Possible to handle total failure of hydraulic system, depending on how surfaces respond to loss of hydraulic pressure, and broken control cables or linkages. Future airplanes incorporate data from Global Positioning System for guidance to any suitable emergency runway in world.

Evaluation of g seat augmentation of fixed-base/moving base simulation for transport landings under two visually imposed runway width conditions

NASA Technical Reports Server (NTRS)

Parrish, R. V.; Steinmetz, G. G.

1983-01-01

Vertical-motion cues supplied by a g-seat to augment platform motion cues in the other five degrees of freedom were evaluated in terms of their effect on objective performance measures obtained during simulated transport landings under visual conditions. In addition to evaluating the effects of the vertical cueing, runway width and magnification effects were investigated. The g-seat was evaluated during fixed base and moving-base operations. Although performance with the g-seat only improved slightly over that with fixed-base operation, combined g-seat platform operation showed no improvement over improvement over platform-only operation. When one runway width at one magnification factor was compared with another width at a different factor, the visual results indicated that the runway width probably had no effect on pilot-vehicle performance. The new performance differences that were detected may be more readily attributed to the extant (existing throughout) increase in vertical velocity induced by the magnification factor used to change the runway width, rather than to the width itself.

Preliminary Human-in-the-Loop Assessment of Procedures for Very-Closely-Spaced Parallel Runways

NASA Technical Reports Server (NTRS)

Verma, Savita; Lozito, Sandra C.; Ballinger, Deborah S.; Trot, Greg; Hardy, Gordon H.; Panda, Ramesh C.; Lehmer, Ronald D.; Kozon, Thomas E.

2010-01-01

Demand in the future air transportation system concept is expected to double or triple by 2025 [1]. Increasing airport arrival rates will help meet the growing demand that could be met with additional runways but the expansion airports is met with environmental challenges for the surrounding communities when using current standards and procedures. Therefore, changes to airport operations can improve airport capacity without adding runways. Building additional runways between current ones, or moving them closer, is a potential solution to meeting the increasing demand, as addressed by the Terminal Area Capacity Enhancing Concept (TACEC). TACEC requires robust technologies and procedures that need to be tested such that operations are not compromised under instrument meteorological conditions. The reduction of runway spacing for independent simultaneous operations dramatically exacerbates the criticality of wake vortex incursion and the calculation of a safe and proper breakout maneuver. The study presented here developed guidelines for such operations by performing a real-time, human-in-the-loop simulation using precision navigation, autopilot-flown approaches, with the pilot monitoring aircraft spacing and the wake vortex safe zone during the approach.

14 CFR Appendix F to Part 60 - Definitions and Abbreviations for Flight Simulation Training Devices

Code of Federal Regulations, 2014 CFR

2014-01-01

... of the various types of data used to design, program, manufacture, modify, and test the FSTD... approaches to Runway 22L and 22R”), those features that may be incomplete or inaccurate may not be able to be... visual model of an airport that is a collection of “non-real world” terrain, instrument approach...

14 CFR Appendix F to Part 60 - Definitions and Abbreviations for Flight Simulation Training Devices

Code of Federal Regulations, 2012 CFR

2012-01-01

... of the various types of data used to design, program, manufacture, modify, and test the FSTD... approaches to Runway 22L and 22R”), those features that may be incomplete or inaccurate may not be able to be... visual model of an airport that is a collection of “non-real world” terrain, instrument approach...

14 CFR Appendix F to Part 60 - Definitions and Abbreviations for Flight Simulation Training Devices

Code of Federal Regulations, 2010 CFR

2010-01-01

... of the various types of data used to design, program, manufacture, modify, and test the FSTD... approaches to Runway 22L and 22R”), those features that may be incomplete or inaccurate may not be able to be... visual model of an airport that is a collection of “non-real world” terrain, instrument approach...

14 CFR Appendix F to Part 60 - Definitions and Abbreviations for Flight Simulation Training Devices

Code of Federal Regulations, 2011 CFR

2011-01-01

... of the various types of data used to design, program, manufacture, modify, and test the FSTD... approaches to Runway 22L and 22R”), those features that may be incomplete or inaccurate may not be able to be... visual model of an airport that is a collection of “non-real world” terrain, instrument approach...

14 CFR Appendix F to Part 60 - Definitions and Abbreviations for Flight Simulation Training Devices

Code of Federal Regulations, 2013 CFR

2013-01-01

... of the various types of data used to design, program, manufacture, modify, and test the FSTD... approaches to Runway 22L and 22R”), those features that may be incomplete or inaccurate may not be able to be... visual model of an airport that is a collection of “non-real world” terrain, instrument approach...

Runway exit designs for capacity improvement demonstrations. Phase 2: Computer model development

NASA Technical Reports Server (NTRS)

Trani, A. A.; Hobeika, A. G.; Kim, B. J.; Nunna, V.; Zhong, C.

1992-01-01

The development is described of a computer simulation/optimization model to: (1) estimate the optimal locations of existing and proposed runway turnoffs; and (2) estimate the geometric design requirements associated with newly developed high speed turnoffs. The model described, named REDIM 2.0, represents a stand alone application to be used by airport planners, designers, and researchers alike to estimate optimal turnoff locations. The main procedures are described in detail which are implemented in the software package and possible applications are illustrated when using 6 major runway scenarios. The main output of the computer program is the estimation of the weighted average runway occupancy time for a user defined aircraft population. Also, the location and geometric characteristics of each turnoff are provided to the user.

Application of Artificial Neural Network to Predict the use of Runway at Juanda International Airport

NASA Astrophysics Data System (ADS)

Putra, J. C. P.; Safrilah

2017-06-01

Artificial neural network approaches are useful to solve many complicated problems. It solves a number of problems in various areas such as engineering, medicine, business, manufacturing, etc. This paper presents an application of artificial neural network to predict a runway capacity at Juanda International Airport. An artificial neural network model of backpropagation and multi-layer perceptron is adopted to this research to learning process of runway capacity at Juanda International Airport. The results indicate that the training data is successfully recognizing the certain pattern of runway use at Juanda International Airport. Whereas, testing data indicate vice versa. Finally, it can be concluded that the approach of uniformity data and network architecture is the critical part to determine the accuracy of prediction results.

Runway safety

DOT National Transportation Integrated Search

2010-02-12

Information provided through analysis of runway incursions is useful in many ways. Analysis of the errors made by pilots, controllers, and vehicle drivers is the first step toward developing error mitigation strategies. Furthermore, successful design...

14 CFR 93.153 - Communications.

Code of Federal Regulations, 2011 CFR

2011-01-01

... operate an aircraft within the airspace specified in § 93.151, or taxi onto the runway at Ketchikan..., or taxi onto the runway at Ketchikan International Airport, unless that person continuously monitors...

STS-31 Discovery, Orbiter Vehicle (OV) 103, lands on EAFB concrete runway 22

NASA Technical Reports Server (NTRS)

1990-01-01

The main landing gear (MLG) of Discovery, Orbiter Vehicle (OV) 103, rides along concrete runway 22 at Edwards Air Force Base (EAFB), California, bringing mission STS-31 to an end. The nose landing gear (NLG) is suspended above the runway prior to touchdown and wheel stop which occurred at 6:51:00 am (Pacific Daylight Time (PDT)). View shows OV-103's starboard side and deployed rudder/speedbrake. EAFB facilities are seen in the distance.

STS-34 Atlantis, OV-104, touches down on runway 23 at EAFB, California

NASA Technical Reports Server (NTRS)

1989-01-01

STS-34 Atlantis, Orbiter Vehicle (OV) 104, main landing gear (MLG) touches down on Runway 23 dry lake bed at Edwards Air Force Base (EAFB), California. The nose landing gear rides above runway before touchdown as the MLG wheels produce a cloud of dust. OV-104's port side profile is captured as it glides by at a speed of approximately 195 knots (224 miles per hour). The tail section with deployed speedbrake/rudder and space shuttle main engines (SSMEs) are visible.

Determining change of bathymetry with GPR method in Ordu-Giresun, a sea-filled airport in the Black Sea, Turkey

NASA Astrophysics Data System (ADS)

Kadioglu, Selma; Kagan Kadioglu, Yusuf

2016-04-01

Ordu-Giresun (OGU) is a newly-constructed airport, the first sea-filled airport in Turkey and in Europe, and the second airport in the world after Osaca-Japan. The airport is between Gulyalı district in Ordu city and Piraziz district in Giresun city in Black Sea -Turkey. A protection breakwater has been constructed by filling a rock approximately 7.435-m long and with an average height of 5.5 m. Then, the Black Sea has been filled until 1 m over the sea level, approximately the area is 1.770.000 m2 wide and includes a runway, aprons and taxiway covered by breakwater. The runway has a 1-m thickness, 3-km length and 45-m width, PCN84 strength, and stone mastic asphalt surface. The aprons has a 240 x 110 m length and PCN110 strength, the taxiway is 250 x 24 m wide. The airport was started to be constructed in July 2011 and it began to serve on 22th May 2015. The aim of this study was to determine the depth of the rock-filled layer and the amount of sinking of the bathymetry which has been determined before filling processing. In addition, before bathymetry determination, unconsolidated sediments had been removed from the bottom of the sea. There were four drilling points to control the sinking of the bathymetry. Therefore, six suitable Ground Penetrating Radar (GPR) profiles were measured, crossing these points with runway and aprons, using 250-MHz and 100-MHz shielded antennas. Starting points of the profiles were in the middle of the runway to merge between depth and thickness changing of the filled layer and bathymetry along the profiles. Surface topography changing was measured spaced 1 m apart with 1 cm sensitivity on each profile. At the same time, similarly the topography changing, bathymetry coordinates was re-arranged along the each profile. Topography corrections were applied to the processed radargrams and then the bottom boundary lines of the rock-filled layer were determined. The maximum height was 3.5 m according to the sea level, which was on the middle point of the runway, representing zero depth of the radargrams of the profiles. To determine the amount of the sinking of the rock filled layer, the first sea level were lined at 3.5 m in depth on the right side depth axes of the radargrams. The second, bathymetry changing lines were placed on the interested radargrams. Finally, differences between the bottom boundary lines of the filled layer and bathymetry lines were compared. The results showed that GPR method could be applied successfully to determine the depth of the rock filled layer in Black Sea and the small amount of the sinking of the bathymetry. Acknowledgement This project has been supported by Cengiz - Içtaş Joint Venture-Turkey. This study is a contribution to the EU funded COST action TU1208 "Civil Engineering Applications of Ground Penetrating Radar" (www.GPRadar.eu, www.cost.eu).

Development of a Bayesian Belief Network Runway Incursion and Excursion Model

NASA Technical Reports Server (NTRS)

Green, Lawrence L.

2014-01-01

In a previous work, a statistical analysis of runway incursion (RI) event data was conducted to ascertain the relevance of this data to the top ten Technical Challenges (TC) of the National Aeronautics and Space Administration (NASA) Aviation Safety Program (AvSP). The study revealed connections to several of the AvSP top ten TC and identified numerous primary causes and contributing factors of RI events. The statistical analysis served as the basis for developing a system-level Bayesian Belief Network (BBN) model for RI events, also previously reported. Through literature searches and data analysis, this RI event network has now been extended to also model runway excursion (RE) events. These RI and RE event networks have been further modified and vetted by a Subject Matter Expert (SME) panel. The combined system-level BBN model will allow NASA to generically model the causes of RI and RE events and to assess the effectiveness of technology products being developed under NASA funding. These products are intended to reduce the frequency of runway safety incidents/accidents, and to improve runway safety in general. The development and structure of the BBN for both RI and RE events are documented in this paper.

Environmental assessment of airport pavement design and construction alternatives : final report.

DOT National Transportation Integrated Search

2016-02-01

The objective of this study is to quantify energy and environmental sustainability of asphalt and concrete : runway pavements using Life-Cycle Assessment (LCA). The design alternatives include runway rehabilitation/reconstruction : designs considered...

Flight Demonstration of Integrated Airport Surface Movement Technologies

NASA Technical Reports Server (NTRS)

Young, Steven D.; Jones, Denise R.

1998-01-01

This document describes operations associated with a set of flight experiments and demonstrations using a Boeing-757-200 research aircraft as part of low visibility landing and surface operations (LVLASO) research activities. To support this experiment, the B-757 performed flight and taxi operations at the Atlanta Hartsfield International Airport in Atlanta, GA. The test aircraft was equipped with experimental displays that were designed to provide flight crews with sufficient information to enable safe, expedient surface operations in any weather condition down to a runway visual range of 300 feet. In addition to flight deck displays and supporting equipment onboard the B-757, there was also a ground-based component of the system that provided for ground controller inputs and surveillance of airport surface movements. Qualitative and quantitative results are discussed.

High Speed Prototype Car Test

NASA Image and Video Library

2014-01-10

CAPE CANAVERAL, Fla. - A Hennessey Venom GT stands on the 3.5-mile long runway between test runs at the Shuttle Landing Facility at NASA's Kennedy Space Center in Florida. The flat concrete runway is one of the few places in the world where high performance automobiles can be tested for aerodynamic and safety designs. Hennessey Performance of Sealy, Texas, worked with Performance Power Racing in West Palm Beach to arrange use of the NASA facility. Performance Power Racing has conducted numerous engineering tests on the runway with a variety of vehicles. Photo credit: NASA/Kim Shiflett

Air Traffic and Operational Data on Selected US Airports with Parallel Runways

NASA Technical Reports Server (NTRS)

Doyle, Thomas M.; McGee, Frank G.

1998-01-01

This report presents information on a number of airports in the country with parallel runways and focuses on those that have at least one pair of parallel runways closer than 4300 ft. Information contained in the report describes the airport's current operational activity as obtained through contact with the facility and from FAA air traffic tower activity data for FY 1997. The primary reason for this document is to provide a single source of information for research to determine airports where Airborne Information for Lateral Spacing (AILS) technology may be applicable.

Expansion of flight simulator capability for study and solution of aircraft directional control problems on runways, phase 1

NASA Technical Reports Server (NTRS)

1975-01-01

The MCAIR five-degree-of-freedom motion-base simulator (MBS) was used in combination with a six-degree-of-freedom aircraft mathematical model to demonstrate the simulation adequacy on uncrowned runways, under various conditions. Known aircraft parameters were used where possible to increase program credibility. Tire-runway friction models were coordinated with personnel of NASA, Langley Research Center. The F-4 experienced pilots representing NASA, FAA, and USAF participated in the 130 approach-touchdown-rollout demonstration and verified the simulation adequacy.

Reliability Modeling Methodology for Independent Approaches on Parallel Runways Safety Analysis

NASA Technical Reports Server (NTRS)

Babcock, P.; Schor, A.; Rosch, G.

1998-01-01

This document is an adjunct to the final report An Integrated Safety Analysis Methodology for Emerging Air Transport Technologies. That report presents the results of our analysis of the problem of simultaneous but independent, approaches of two aircraft on parallel runways (independent approaches on parallel runways, or IAPR). This introductory chapter presents a brief overview and perspective of approaches and methodologies for performing safety analyses for complex systems. Ensuing chapter provide the technical details that underlie the approach that we have taken in performing the safety analysis for the IAPR concept.

14 CFR 91.605 - Transport category civil airplane weight limitations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... grooved or porous friction course runways, if provided in the Airplane Flight Manual, may be used only for runways that are grooved or treated with a porous friction course (PFC) overlay, and that the operator...

Three-track runway and taxiway profiles measured at international airports I and J

NASA Technical Reports Server (NTRS)

Hall, A. W.

1972-01-01

Three-track runway and taxiway profiles are presented for use in studies of airplane response to ground roughness. Tabulated and plotted data for two international airports, (designated I and J), are included.

14 CFR 151.85 - Special treatment areas.

Code of Federal Regulations, 2013 CFR

2013-01-01

... adjacent to runway ends, holding aprons, and taxiways to prevent erosion from the blast effects of the... end of the runway. (b) Holding aprons—a stabilized area up to 50 feet from the edge of the pavement...

14 CFR 151.85 - Special treatment areas.

Code of Federal Regulations, 2014 CFR

2014-01-01

... adjacent to runway ends, holding aprons, and taxiways to prevent erosion from the blast effects of the... end of the runway. (b) Holding aprons—a stabilized area up to 50 feet from the edge of the pavement...

14 CFR 151.85 - Special treatment areas.

Code of Federal Regulations, 2012 CFR

2012-01-01

... adjacent to runway ends, holding aprons, and taxiways to prevent erosion from the blast effects of the... end of the runway. (b) Holding aprons—a stabilized area up to 50 feet from the edge of the pavement...

Analysis of MLS Based Surveillance System (MLSS) Concepts

DOT National Transportation Integrated Search

1989-04-01

This report examines a number of surveillance system concepts to support safe independent runway approaches and converging runways under weather conditons. All surveillance conepts are based on the use of MLS signals. The resultin surveillance is ava...

Action-specific effects in aviation: what determines judged runway size?

PubMed

Gray, Rob; Navia, José Antonio; Allsop, Jonathan

2014-01-01

Several recent studies have shown that the performance of a skill that involves acting on a goal object can influence one's judgment of the size of that object. The present study investigated this effect in an aviation context. Novice pilots were asked to perform a series of visual approach and landing manoeuvres in a flight simulator. After each landing, participants next performed a task in which runway size was judged for different simulated altitudes. Gaze behaviour and control stick kinematics were also analyzed. There were significant relationships between judged runway size and multiple action-related variables including touchdown velocity, time fixating the runway, and the magnitude and frequency of control inputs. These findings suggest that relationship between the perception of a target object and action is not solely determined by performance success or failure but rather involves a relationship between multiple variables that reflect the actor's ability.

Runways at small airports are deteriorating because of deferred maintenance: Action needed by FAA and the Congress

NASA Astrophysics Data System (ADS)

1982-09-01

Runways at many small airports are deteriorating faster than necessary because airport owners--usually local governments--have deferred critical maintenance. The result is damage to the runways' basic structure and a shortened useful life if they are not repaired. Based on GAO's review of 46 airports, studies by others, and the views of FAA officials, deferred maintenance is apparently a longstanding nationwide problem. Lack of funds is cited by airport owners as the primary reason for not performing needed maintenance; however, the Federal Aviation Administration's apathy to bring about satisfactory maintenance is a contributing cause. GAO is recommending actions that FAA can take to help ensure that runways at small airports are properly maintained. The Congress should recognize the airport owners' lack of resources to properly maintain airports when considering future revisions to the Airport Improvement Program.

A Concept for Airborne Precision Spacing for Dependent Parallel Approaches

NASA Technical Reports Server (NTRS)

Barmore, Bryan E.; Baxley, Brian T.; Abbott, Terence S.; Capron, William R.; Smith, Colin L.; Shay, Richard F.; Hubbs, Clay

2012-01-01

The Airborne Precision Spacing concept of operations has been previously developed to support the precise delivery of aircraft landing successively on the same runway. The high-precision and consistent delivery of inter-aircraft spacing allows for increased runway throughput and the use of energy-efficient arrivals routes such as Continuous Descent Arrivals and Optimized Profile Descents. This paper describes an extension to the Airborne Precision Spacing concept to enable dependent parallel approach operations where the spacing aircraft must manage their in-trail spacing from a leading aircraft on approach to the same runway and spacing from an aircraft on approach to a parallel runway. Functionality for supporting automation is discussed as well as procedures for pilots and controllers. An analysis is performed to identify the required information and a new ADS-B report is proposed to support these information needs. Finally, several scenarios are described in detail.

Method and device for landing aircraft dependent on runway occupancy time

NASA Technical Reports Server (NTRS)

Ghalebsaz Jeddi, Babak (Inventor)

2012-01-01

A technique for landing aircraft using an aircraft landing accident avoidance device is disclosed. The technique includes determining at least two probability distribution functions; determining a safe lower limit on a separation between a lead aircraft and a trail aircraft on a glide slope to the runway; determining a maximum sustainable safe attempt-to-land rate on the runway based on the safe lower limit and the probability distribution functions; directing the trail aircraft to enter the glide slope with a target separation from the lead aircraft corresponding to the maximum sustainable safe attempt-to-land rate; while the trail aircraft is in the glide slope, determining an actual separation between the lead aircraft and the trail aircraft; and directing the trail aircraft to execute a go-around maneuver if the actual separation approaches the safe lower limit. Probability distribution functions include runway occupancy time, and landing time interval and/or inter-arrival distance.

Langley Aircraft Landing Dynamics Facility

NASA Technical Reports Server (NTRS)

Davis, Pamela A.; Stubbs, Sandy M.; Tanner, John A.

1987-01-01

The Langley Research Center has recently upgraded the Landing Loads Track (LLT) to improve the capability of low-cost testing of conventional and advanced landing gear systems. The unique feature of the Langley Aircraft Landing Dynamics Facility (ALDF) is the ability to test aircraft landing gear systems on actual runway surfaces at operational ground speeds and loading conditions. A historical overview of the original LLT is given, followed by a detailed description of the new ALDF systems and operational capabilities.

NCEL (Naval Civil Engineering Laboratory) Quarterly Abstracts of Technical Documents, 1 January 1986 to 31 December 1986.

DTIC Science & Technology

1986-12-31

underwater use and evaluated in laboratory and field tests. One of the three instruments was a magnetic rebar locator that locates rebar in concrete ...structures and measures the amount of concrete cover over the rebar . Another instrument was a Schmidt hammer that evaluates the surface hardness of the...Used as Boiler Fuel ..... .................. 3 N-1744 Blistering of Asphalt Pavement Overlay on Runway 14-32 at MCAS Bea, fort, South Carolina

Wear, friction, and temperature characteristics of an aircraft tire undergoing braking and cornering

NASA Technical Reports Server (NTRS)

Mccarty, J. L.; Yager, T. J.; Riccitiello, S. R.

1979-01-01

An investigation to evaluate the wear, friction, and temperature characteristics of aircraft tire treads fabricated from different elastomers is presented. The braking and cornering tests performed on aircraft tires retreaded with currently employed and experimental elastomers are described. The tread wear rate is discussed in relation to the slip ratio during braking and yaw angle during cornering. The extent of wear in either operational mode is examined in relation to the runway surface.

Effect of temperature on composite sandwich structures subjected to low velocity impact. [aircraft construction materials

NASA Technical Reports Server (NTRS)

Sharma, A. V.

1980-01-01

The effect of low velocity projectile impact on sandwich-type structural components was investigated. The materials used in the fabrication of the impact surface were graphite-, Kevlar-, and boron-fibers with appropriate epoxy matrices. The testing of the specimens was performed at moderately low- and high-temperatures as well as at room temperature to assess the impact-initiated strength degradation of the laminates. Eleven laminates with different stacking sequences, orientations, and thicknesses were tested. The low energy projectile impact is considered to simulate the damage caused by runway debris, the dropping of the hand tools during servicing, etc., on the secondary aircraft structures fabricated with the composite materials. The results show the preload and the impact energy combinations necessary to cause catastrophic failure in the laminates tested. A set of faired curves indicating the failure thresholds is shown separately for the tension-and compression-loaded laminates. The specific-strengths and -modulii for the various laminates tested are also given.

Impact-initiated damage thresholds in composites

NASA Technical Reports Server (NTRS)

Sharma, A. V.

1980-01-01

An experimental investigation was conducted to study the effect of low velocity projectile impact on the sandwich-type structural components. The materials used in the fabrication of the impact surface were graphite-, Kevlar-, and boron-fibers with appropriate epoxy matrices. The testing of the specimens was performed at moderately low- and high-temperatures as well as at room temperature to assess the impact-initiated strength degradation of the laminates. Eleven laminates with different stacking sequences, orientations, and thicknesses were tested. The low energy projectile impact is considered to simulate the damage caused by runway debris, dropping of the hand tools during servicing, etc., on the secondary aircraft structures fabricated with the composite materials. The results show the preload and the impact energy combinations necessary to cause catastrophic failures in the laminates tested. A set of faired curves indicating the failure thresholds is shown separately for the tension- and compression-loaded laminates. The specific-strengths and -moduli for the various laminates tested are also given.

Evaluation of a driving simulator for ground-vehicle operator training

DOT National Transportation Integrated Search

2006-01-31

Improving runway safety is part of the Federal Aviation Administration (FAA) Flight Plan (FAA, 2005) with annual goals established for the reduction of runway incursions, including vehicle pedestrian deviations (VPDs). Reducing VPDs is a difficult ta...

An evaluation of winter operational runway friction measurement equipment, procedures and research

DOT National Transportation Integrated Search

1995-01-25

For many years, the aviation community has struggled with runway friction reporting practices. Airport operations personnel, in taking on the responsibility for conducting friction measurements during winter storms, work diligently to keep up with ra...

Airport pavement marking evaluation for reducing runway incursion

DOT National Transportation Integrated Search

2001-02-01

This study was undertaken to evaluate the widening of airport pavement marking in order to enhance their recognition. Results of this evaluation are aimed at reducing the potential of runway incursions and incidents by making airports pavement markin...

White Sands Space Harbor Area 1, Crash/Rescue Standby Support GPS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

White Sands Space Harbor Area 1, Crash/Rescue Standby Support GPS Buildings, East side of Runway 17/35, approximately 2,650 feet north of intersection with Runway 23/05, White Sands, Dona Ana County, NM

AERIAL OF SHUTTLE LANDING FACILITY [SLF] POURING OF CONCRETE

NASA Technical Reports Server (NTRS)

1975-01-01

AERIAL OF SHUTTLE LANDING FACILITY [SLF] POURING OF CONCRETE KSC-375C-10036.31 108-KSC-375C-10036.31, P-21426, ARCHIVE-04502 Aerial oblique of Shuttle runway facilities. Pouring concrete on runway. Direction north - altitude 100'.

STS-41 Discovery, OV-103, glides over concrete runway 22 at EAFB, California

NASA Technical Reports Server (NTRS)

1990-01-01

STS-41 Discovery, Orbiter Vehicle (OV) 103, with nose landing gear (NLG) and main landing gear (MLG) deployed, glides over concrete runway 22 at Edwards Air Force Base (EAFB), California, prior to touchdown.

14 CFR Appendix I to Part 151 - Appendix I to Part 151

Code of Federal Regulations, 2013 CFR

2013-01-01

.... AC 150/5325-4 Runway Length Requirements for Airport Design. AC 150/5330-2 Runway/Taxiway Widths and... Lighting Circuits To Be Installed in Airport Pavements. AC 150/5345-31 Specification for L-833 Individual...

14 CFR Appendix I to Part 151 - Appendix I to Part 151

Code of Federal Regulations, 2010 CFR

2010-01-01

.... AC 150/5325-4 Runway Length Requirements for Airport Design. AC 150/5330-2 Runway/Taxiway Widths and... Lighting Circuits To Be Installed in Airport Pavements. AC 150/5345-31 Specification for L-833 Individual...

14 CFR Appendix I to Part 151 - Appendix I to Part 151

Code of Federal Regulations, 2011 CFR

2011-01-01

.... AC 150/5325-4 Runway Length Requirements for Airport Design. AC 150/5330-2 Runway/Taxiway Widths and... Lighting Circuits To Be Installed in Airport Pavements. AC 150/5345-31 Specification for L-833 Individual...

14 CFR Appendix I to Part 151 - Appendix I to Part 151

Code of Federal Regulations, 2014 CFR

2014-01-01

.... AC 150/5325-4 Runway Length Requirements for Airport Design. AC 150/5330-2 Runway/Taxiway Widths and... Lighting Circuits To Be Installed in Airport Pavements. AC 150/5345-31 Specification for L-833 Individual...

14 CFR Appendix I to Part 151 - Appendix I to Part 151

Code of Federal Regulations, 2012 CFR

2012-01-01

.... AC 150/5325-4 Runway Length Requirements for Airport Design. AC 150/5330-2 Runway/Taxiway Widths and... Lighting Circuits To Be Installed in Airport Pavements. AC 150/5345-31 Specification for L-833 Individual...

Runway safety : it's everybody's business

DOT National Transportation Integrated Search

2001-07-01

This booklet tells pilots and controllers what they can do to help prevent runway incursions by helping them to avoid situations that reduce errors and alerting them to situations as extra vigilance is required. It also provides information on how co...

Ground-vehicle operator training using a low-cost simulator

DOT National Transportation Integrated Search

2006-05-01

Pilots, controllers, and ground-vehicle operators all have an important role in runway safety. Their actions, either individually or collectively can cause or avert a runway incursion. The roles and responsibilities of pilots and controllers in this ...

Wake turbulence limits on paired approaches to parallel runways

DOT National Transportation Integrated Search

2002-07-01

Wake turbulence considerations currently restrict the use of parallel runways less than 2500 ft (762 m) apart. : However, wake turbulence is not a factor if there are appropriate limits on allowed longitudinal pair spacings : and/or allowed crosswind...

Exact and Heuristic Algorithms for Runway Scheduling

NASA Technical Reports Server (NTRS)

Malik, Waqar A.; Jung, Yoon C.

2016-01-01

This paper explores the Single Runway Scheduling (SRS) problem with arrivals, departures, and crossing aircraft on the airport surface. Constraints for wake vortex separations, departure area navigation separations and departure time window restrictions are explicitly considered. The main objective of this research is to develop exact and heuristic based algorithms that can be used in real-time decision support tools for Air Traffic Control Tower (ATCT) controllers. The paper provides a multi-objective dynamic programming (DP) based algorithm that finds the exact solution to the SRS problem, but may prove unusable for application in real-time environment due to large computation times for moderate sized problems. We next propose a second algorithm that uses heuristics to restrict the search space for the DP based algorithm. A third algorithm based on a combination of insertion and local search (ILS) heuristics is then presented. Simulation conducted for the east side of Dallas/Fort Worth International Airport allows comparison of the three proposed algorithms and indicates that the ILS algorithm performs favorably in its ability to find efficient solutions and its computation times.

Final Environmental Assessment for Munitions Storage Area at Langley Air Force Base, Virginia

DTIC Science & Technology

2004-08-01

Existing Conditions LAND USE Land uses on Langley AFB are grouped by function in distinct geographic areas. For example, aircraft operations and...1998a) is used to coordinate natural resource management. Langley’s Urban Forest Inventory Review and Management Plan (Davey Resource Group 1997...following data to develop noise contours: aircraft types, runway utilization patterns, engine power settings, airspeeds, altitude profiles , flight track

Comparison of Pilots' Situational Awareness While Monitoring Autoland Approaches Using Conventional and Advanced Flight Display Formats

NASA Technical Reports Server (NTRS)

Kramer, Lynda J.; Busquets, Anthony M.

2000-01-01

A simulation experiment was performed to assess situation awareness (SA) and workload of pilots while monitoring simulated autoland operations in Instrument Meteorological Conditions with three advanced display concepts: two enhanced electronic flight information system (EFIS)-type display concepts and one totally synthetic, integrated pictorial display concept. Each concept incorporated sensor-derived wireframe runway and iconic depictions of sensor-detected traffic in different locations on the display media. Various scenarios, involving conflicting traffic situation assessments, main display failures, and navigation/autopilot system errors, were used to assess the pilots' SA and workload during autoland approaches with the display concepts. From the results, for each scenario, the integrated pictorial display concept provided the pilots with statistically equivalent or substantially improved SA over the other display concepts. In addition to increased SA, subjective rankings indicated that the pictorial concept offered reductions in overall pilot workload (in both mean ranking and spread) over the two enhanced EFIS-type display concepts. Out of the display concepts flown, the pilots ranked the pictorial concept as the display that was easiest to use to maintain situational awareness, to monitor an autoland approach, to interpret information from the runway and obstacle detecting sensor systems, and to make the decision to go around.

White Sands Space Harbor Area 1, Runway 17/35, Extending 35,000 ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

White Sands Space Harbor Area 1, Runway 17/35, Extending 35,000 feet north from Range Road 10, beginning approximately 4.2 miles northeast of intersection with Range Road 7, White Sands, Dona Ana County, NM

Three-track runway and taxiway profiles measured at International Airports E and F

NASA Technical Reports Server (NTRS)

Hall, A. W.

1971-01-01

Three-track runway and taxiway profiles are presented for use in studies of airplane response to ground roughness. This report presents the tabulated and plotted data for two international airports (designed airports E and F).

An analysis of runway-taxiway transgressions at controlled airports

DOT National Transportation Integrated Search

1981-04-01

The purpose of this study was to determine the cause of aircraft making inadvertent or unauthorized takeoffs and transgressions onto active runways during takeoff and landing operations. The study was conducted in four phases: (1) Prior studies by FA...

77 FR 49852 - Notice of Passenger Facility Charge (PFC) Approvals and Disapprovals

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-17

... of Projects Approved for Collection and Use: Runway 11/29 pavement rehabilitation. Taxiway B pavement rehabilitation. Runway 15/33 pavement rehabilitation. Aircraft rescue and firefighting equipment acquisition. Security enhancements. Rehabilitate concrete commercial apron. General aviation apron pavement...

Three-track runway and taxiway profiles measured at international airports G and H

NASA Technical Reports Server (NTRS)

Hall, A. W.

1972-01-01

Three-track runway and taxiway profiles are presented for use in studies of airplane response to ground roughness. This report presents the tabulated and plotted data for two international airports (designated airports G and H).

Ground winds for Kennedy Space Center, Florida, 1979 revision

NASA Technical Reports Server (NTRS)

Johnson, D. L.; Brown, S. C.

1979-01-01

Revised ground-level runway wind statistics for the Kennedy Space Center, Florida area are presented. Crosswind, headwind, tailwind, and headwind reversal percentage frequencies are given with respect to month and hour for the Kennedy Space Center Space Shuttle runway.

Calibration validation for the new generation runway visual range system

DOT National Transportation Integrated Search

2000-07-01

A forward scattermeter, consisting of transmitter and receiver heads mounted on a fork, is used in the New Genreration Runway Visual Range (NGRVR) System to assess the clarity of the atmosphere. The scattermeter is calibrated by comparison with refer...

High Speed Prototype Car Test

NASA Image and Video Library

2014-01-10

CAPE CANAVERAL, Fla. - An engineer readies a Hennessey Venom GT for test runs on the 3.5-mile long runway at the Shuttle Landing Facility at NASA's Kennedy Space Center in Florida. The flat concrete runway is one of the few places in the world where high performance automobiles can be tested for aerodynamic and safety designs. Hennessey Performance of Sealy, Texas, worked with Performance Power Racing in West Palm Beach to arrange use of the NASA facility. Performance Power Racing has conducted numerous engineering tests on the runway with a variety of vehicles. Photo credit: NASA/Kim Shiflett

High Speed Prototype Car Test

NASA Image and Video Library

2014-01-10

CAPE CANAVERAL, Fla. - Mechanics, engineers and Driver Brian Smith, in jumpsuit, ready a Hennessey Venom GT for test runs on the 3.5-mile long runway at the Shuttle Landing Facility at NASA's Kennedy Space Center in Florida. The flat concrete runway is one of the few places in the world where high performance automobiles can be tested for aerodynamic and safety designs. Hennessey Performance of Sealy, Texas, worked with Performance Power Racing in West Palm Beach to arrange use of the NASA facility. Performance Power Racing has conducted numerous engineering tests on the runway with a variety of vehicles. Photo credit: NASA/Kim Shiflett

High Speed Prototype Car Test

NASA Image and Video Library

2014-01-10

CAPE CANAVERAL, Fla. - Mechanics and engineers ready a Hennessey Venom GT for test runs on the 3.5-mile long runway at the Shuttle Landing Facility at NASA's Kennedy Space Center in Florida. The flat concrete runway is one of the few places in the world where high performance automobiles can be tested for aerodynamic and safety designs. Hennessey Performance of Sealy, Texas, worked with Performance Power Racing in West Palm Beach to arrange use of the NASA facility. Performance Power Racing has conducted numerous engineering tests on the runway with a variety of vehicles. Photo credit: NASA/Kim Shiflett

A new FOD recognition algorithm based on multi-source information fusion and experiment analysis

NASA Astrophysics Data System (ADS)

Li, Yu; Xiao, Gang

2011-08-01

Foreign Object Debris (FOD) is a kind of substance, debris or article alien to an aircraft or system, which would potentially cause huge damage when it appears on the airport runway. Due to the airport's complex circumstance, quick and precise detection of FOD target on the runway is one of the important protections for airplane's safety. A multi-sensor system including millimeter-wave radar and Infrared image sensors is introduced and a developed new FOD detection and recognition algorithm based on inherent feature of FOD is proposed in this paper. Firstly, the FOD's location and coordinate can be accurately obtained by millimeter-wave radar, and then according to the coordinate IR camera will take target images and background images. Secondly, in IR image the runway's edges which are straight lines can be extracted by using Hough transformation method. The potential target region, that is, runway region, can be segmented from the whole image. Thirdly, background subtraction is utilized to localize the FOD target in runway region. Finally, in the detailed small images of FOD target, a new characteristic is discussed and used in target classification. The experiment results show that this algorithm can effectively reduce the computational complexity, satisfy the real-time requirement and possess of high detection and recognition probability.

Experiment Description and Results for Arrival Operations Using Interval Management with Spacing to Parallel Dependent Runways (IMSPiDR)

NASA Technical Reports Server (NTRS)

Baxley, Brian T.; Murdoch, Jennifer L.; Swieringa, Kurt A.; Barmore, Bryan E.; Capron, William R.; Hubbs, Clay E.; Shay, Richard F.; Abbott, Terence S.

2013-01-01

The predicted increase in the number of commercial aircraft operations creates a need for improved operational efficiency. Two areas believed to offer increases in aircraft efficiency are optimized profile descents and dependent parallel runway operations. Using Flight deck Interval Management (FIM) software and procedures during these operations, flight crews can achieve by the runway threshold an interval assigned by air traffic control (ATC) behind the preceding aircraft that maximizes runway throughput while minimizing additional fuel consumption and pilot workload. This document describes an experiment where 24 pilots flew arrivals into the Dallas Fort-Worth terminal environment using one of three simulators at NASA?s Langley Research Center. Results indicate that pilots delivered their aircraft to the runway threshold within +/- 3.5 seconds of their assigned time interval, and reported low workload levels. In general, pilots found the FIM concept, procedures, speeds, and interface acceptable. Analysis of the time error and FIM speed changes as a function of arrival stream position suggest the spacing algorithm generates stable behavior while in the presence of continuous (wind) or impulse (offset) error. Concerns reported included multiple speed changes within a short time period, and an airspeed increase followed shortly by an airspeed decrease.

Performance Predictions for Proposed ILS Facilities at St. Louis Municipal Airport

DOT National Transportation Integrated Search

1978-01-01

The results of computer simulations of performance of proposed ILS facilities on Runway 12L/30R at St. Louis Municipal Airport (Lambert Field) are reported. These simulations indicate that an existing industrial complex located near the runway is com...

X-48C Flies Over Intersecting Runways

NASA Image and Video Library

2013-02-28

The X-48C Hybrid Wing Body research aircraft flew over the intersection of several runways adjacent to the compass rose on Rogers Dry Lake at Edwards Air Force Base during one of the sub-scale aircraft's final test flights on Feb. 28, 2013.

Evaluation of a Tactical Surface Metering Tool for Charlotte Douglas International Airport via Human-in-the-Loop Simulation

NASA Technical Reports Server (NTRS)

Verma, Savita; Lee, Hanbong; Dulchinos, Victoria L.; Martin, Lynne; Stevens, Lindsay; Jung, Yoon; Chevalley, Eric; Jobe, Kim; Parke, Bonny

2017-01-01

NASA has been working with the FAA and aviation industry partners to develop and demonstrate new concepts and technologies that integrate arrival, departure, and surface traffic management capabilities. In March 2017, NASA conducted a human-in-the-loop (HITL) simulation for integrated surface and airspace operations, modeling Charlotte Douglas International Airport, to evaluate the operational procedures and information requirements for the tactical surface metering tool, and data exchange elements between the airline controlled ramp and ATC Tower. In this paper, we focus on the calibration of the tactical surface metering tool using various metrics measured from the HITL simulation results. Key performance metrics include gate hold times from pushback advisories, taxi-in-out times, runway throughput, and departure queue size. Subjective metrics presented in this paper include workload, situational awareness, and acceptability of the metering tool and its calibration.

Evaluation of a Tactical Surface Metering Tool for Charlotte Douglas International Airport Via Human-in-the-Loop Simulation

NASA Technical Reports Server (NTRS)

Verma, Savita; Lee, Hanbong; Martin, Lynne; Stevens, Lindsay; Jung, Yoon; Dulchinos, Victoria; Chevalley, Eric; Jobe, Kim; Parke, Bonny

2017-01-01

NASA has been working with the FAA and aviation industry partners to develop and demonstrate new concepts and technologies that integrate arrival, departure, and surface traffic management capabilities. In March 2017, NASA conducted a human-in-the-loop (HITL) simulation for integrated surface and airspace operations, modeling Charlotte Douglas International Airport, to evaluate the operational procedures and information requirements for the tactical surface metering tool, and data exchange elements between the airline controlled ramp and ATC Tower. In this paper, we focus on the calibration of the tactical surface metering tool using various metrics measured from the HITL simulation results. Key performance metrics include gate hold times from pushback advisories, taxi-in/out times, runway throughput, and departure queue size. Subjective metrics presented in this paper include workload, situational awareness, and acceptability of the metering tool and its calibration

Project CHECO Southeast Asia Report. Forward Airfields for Tactical Airlift in SEA

DTIC Science & Technology

1970-06-15

publications, this is an authen- tic s-sment of the effectiveness of USAF airpower in PACOM. ef /o a , Major General, USAF I/ m i ii l UNCLASSIFIED...Australian Air Force (RAAF) crews were airborne 35,569 times in 1969, with cargo that ranged from troops to chickens, cement , rice, ammunition, cattle...Runway surfaces--clay, laterite , limestone, light steel matting (M8Al), or sod, depending on the aircraft involved-- were expected to sustain 700 traffic

Safety Grooving

NASA Technical Reports Server (NTRS)

1985-01-01

Safety grooving, the cutting of grooves in concrete to increase traction and prevent injury, was first developed to reduce aircraft accidents on wet runways. Represented by the International Grooving and Grinding Association (IG&GA), the industry expanded into highway and pedestrian applications. The technique originated at Langley, which assisted in testing the grooving at airports and on highways. Skidding was reduced, stopping distance decreased, and a vehicle's cornering ability on curves was increased. The process has been extended to animal holding pens, steps, parking lots and other potentially slippery surfaces.

77 FR 14584 - Notice of Passenger Facility Charge (PFC) Approvals and Disapprovals

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-12

... square yards). Modify supplemental wind cones. Runway 8/26 pavement rejuvenation. Purchase snow removal equipment--high-speed snow plow. Master plan/land use. Design passenger terminal remodel. Install runway... lighting and cable rehabilitation. Construct improvements of terminal building. Design reconstruction of...

Development of a computer program data base of a navigation aid environment for simulated IFR flight and landing studies

NASA Technical Reports Server (NTRS)

Bergeron, H. P.; Haynie, A. T.; Mcdede, J. B.

1980-01-01

A general aviation single pilot instrument flight rule simulation capability was developed. Problems experienced by single pilots flying in IFR conditions were investigated. The simulation required a three dimensional spatial navaid environment of a flight navigational area. A computer simulation of all the navigational aids plus 12 selected airports located in the Washington/Norfolk area was developed. All programmed locations in the list were referenced to a Cartesian coordinate system with the origin located at a specified airport's reference point. All navigational aids with their associated frequencies, call letters, locations, and orientations plus runways and true headings are included in the data base. The simulation included a TV displayed out-the-window visual scene of country and suburban terrain and a scaled model runway complex. Any of the programmed runways, with all its associated navaids, can be referenced to a runway on the airport in this visual scene. This allows a simulation of a full mission scenario including breakout and landing.

Formal Verification of the Runway Safety Monitor

NASA Technical Reports Server (NTRS)

Siminiceanu, Radu; Ciardo, Gianfranco

2006-01-01

The Runway Safety Monitor (RSM) designed by Lockheed Martin is part of NASA's effort to reduce runway accidents. We developed a Petri net model of the RSM protocol and used the model checking functions of our tool SMART to investigate a number of safety properties in RSM. To mitigate the impact of state-space explosion, we built a highly discretized model of the system, obtained by partitioning the monitored runway zone into a grid of smaller volumes and by considering scenarios involving only two aircraft. The model also assumes that there are no communication failures, such as bad input from radar or lack of incoming data, thus it relies on a consistent view of reality by all participants. In spite of these simplifications, we were able to expose potential problems in the RSM conceptual design. Our findings were forwarded to the design engineers, who undertook corrective action. Additionally, the results stress the efficiency attained by the new model checking algorithms implemented in SMART, and demonstrate their applicability to real-world systems.

Runway Incursion Prevention System ADS-B and DGPS Data Link Analysis Dallas-Fort Worth International Airport

NASA Technical Reports Server (NTRS)

Timmerman, J.; Jones, Denise R. (Technical Monitor)

2001-01-01

A Runway Incursion Prevention System (RIPS) was tested at the Dallas - Ft. Worth International Airport in October 2000. The system integrated airborne and ground components to provide both pilots and controllers with enhanced situational awareness, supplemental guidance cues, a real-time display of traffic information, and warning of runway incursions in order to prevent runway incidents while also improving operational capability. Rockwell Collins provided and supported a prototype Automatic Dependent Surveillance - Broadcast (ADS-B) system using 1090 MHz and a prototype Differential GPS (DGPS) system onboard the NASA Boeing 757 research aircraft. This report describes the Rockwell Collins contributions to the RIPS flight test, summarizes the development process, and analyzes both ADS-B and DGPS data collected during the flight test. In addition, results are report on interoperability tests conducted between the NASA Advanced General Aviation Transport Experiments (AGATE) ADS-B flight test system and the NASA Boeing 757 ADS-B system.

Expansion of flight simulator capability for study and solution of aircraft directional control problems on runways

NASA Technical Reports Server (NTRS)

Kibbee, G. W.

1978-01-01

The development, evaluation, and evaluation results of a DC-9-10 runway directional control simulator are described. An existing wide bodied flight simulator was modified to this aircraft configuration. The simulator was structured to use either two of antiskid simulations; (1) an analog mechanization that used aircraft hardware; or (2) a digital software simulation. After the simulation was developed it was evaluated by 14 pilots who made 818 simulated flights. These evaluations involved landings, rejected takeoffs, and various ground maneuvers. Qualitatively most pilots evaluated the simulator as realistic with good potential especially for pilot training for adverse runway conditions.

Estimating the Effects of the Terminal Area Productivity Program

NASA Technical Reports Server (NTRS)

Lee, David A.; Kostiuk, Peter F.; Hemm, Robert V., Jr.; Wingrove, Earl R., III; Shapiro, Gerald

1997-01-01

The report describes methods and results of an analysis of the technical and economic benefits of the systems to be developed in the NASA Terminal Area Productivity (TAP) program. A runway capacity model using parameters that reflect the potential impact of the TAP technologies is described. The runway capacity model feeds airport specific models which are also described. The capacity estimates are used with a queuing model to calculate aircraft delays, and TAP benefits are determined by calculating the savings due to reduced delays. The report includes benefit estimates for Boston Logan and Detroit Wayne County airports. An appendix includes a description and listing of the runway capacity model.

KSC-07pd0889

NASA Image and Video Library

2007-04-16

KENNEDY SPACE CENTER, FLA. -- Pilot Rick Svetkoff taxis a Starfighter F-104 down the runway on the Shuttle Landing Facility at Kennedy Space Center. The aircraft will take part in a series of pathfinder test missions from the space shuttle runway. Two flights will generate test data to validate sonic boom assumptions about the potential impacts of suborbital and orbital commercial spaceflight from the facility. NASA is assessing the environmental impact of such flights. Starfighters Inc. of Clearwater, Fla., will perform the flights to help in assessing suborbital space launch trajectories from the runway and paving the way for future commercial space tourism and research flights from the facility. Photo credit: NASA/Kim Shiflett

KSC-07pd0913

NASA Image and Video Library

2007-04-17

KENNEDY SPACE CENTER, FLA. -- The Starfighter F-104 approaches the runway at the KSC Shuttle Landing Facility for a landing after its test flight. The aircraft is taking part in a series of pathfinder test missions from the space shuttle runway. Two flights will generate test data to validate sonic boom assumptions about the potential impacts of suborbital and orbital commercial spaceflight from the facility. NASA is assessing the environmental impact of such flights. Starfighters Inc. of Clearwater, Fla., will perform the flights to help in assessing suborbital space launch trajectories from the runway and paving the way for future commercial space tourism and research flights from the facility. Photo credit: NASA/Kim Shiflett

KSC-07pd0914

NASA Image and Video Library

2007-04-17

KENNEDY SPACE CENTER, FLA. -- The Starfighter F-104 lands on the runway at the KSC Shuttle Landing Facility after its test flight. The aircraft is taking part in a series of pathfinder test missions from the space shuttle runway. Two flights will generate test data to validate sonic boom assumptions about the potential impacts of suborbital and orbital commercial spaceflight from the facility. NASA is assessing the environmental impact of such flights. Starfighters Inc. of Clearwater, Fla., will perform the flights to help in assessing suborbital space launch trajectories from the runway and paving the way for future commercial space tourism and research flights from the facility. Photo credit: NASA/Kim Shiflett

Black Box Testing: Experiments with Runway Incursion Advisory Alerting System

NASA Technical Reports Server (NTRS)

Mukkamala, Ravi

2005-01-01

This report summarizes our research findings on the Black box testing of Runway Incursion Advisory Alerting System (RIAAS) and Runway Safety Monitor (RSM) system. Developing automated testing software for such systems has been a problem because of the extensive information that has to be processed. Customized software solutions have been proposed. However, they are time consuming to develop. Here, we present a less expensive, and a more general test platform that is capable of performing complete black box testing. The technique is based on the classification of the anomalies that arise during Monte Carlo simulations. In addition, we also discuss a generalized testing tool (prototype) that we have developed.

Precision Departure Release Capability (PDRC) Overview and Results: NASA to FAA Research Transition

NASA Technical Reports Server (NTRS)

Engelland, Shawn; Davis, Tom.

2013-01-01

NASA researchers developed the Precision Departure Release Capability (PDRC) concept to improve the tactical departure scheduling process. The PDRC system is comprised of: 1) a surface automation system that computes ready time predictions and departure runway assignments, 2) an en route scheduling automation tool that uses this information to estimate ascent trajectories to the merge point and computes release times and, 3) an interface that provides two-way communication between the two systems. To minimize technology transfer issues and facilitate its adoption by TMCs and Frontline Managers (FLM), NASA developed the PDRC prototype using the Surface Decision Support System (SDSS) for the Tower surface automation tool, a research version of the FAA TMA (RTMA) for en route automation tool and a digital interface between the two DSTs to facilitate coordination.

Evaluation of an Airborne Spacing Concept, On-Board Spacing Tool, and Pilot Interface

NASA Technical Reports Server (NTRS)

Swieringa, Kurt; Murdoch, Jennifer L.; Baxley, Brian; Hubbs, Clay

2011-01-01

The number of commercial aircraft operations is predicted to increase in the next ten years, creating a need for improved operational efficiency. Two areas believed to offer significant increases in efficiency are optimized profile descents and dependent parallel runway operations. It is envisioned that during both of these types of operations, flight crews will precisely space their aircraft behind preceding aircraft at air traffic control assigned intervals to increase runway throughput and maximize the use of existing infrastructure. This paper describes a human-in-the-loop experiment designed to study the performance of an onboard spacing algorithm and pilots ratings of the usability and acceptability of an airborne spacing concept that supports dependent parallel arrivals. Pilot participants flew arrivals into the Dallas Fort-Worth terminal environment using one of three different simulators located at the National Aeronautics and Space Administration s (NASA) Langley Research Center. Scenarios were flown using Interval Management with Spacing (IM-S) and Required Time of Arrival (RTA) control methods during conditions of no error, error in the forecast wind, and offset (disturbance) to the arrival flow. Results indicate that pilots delivered their aircraft to the runway threshold within +/- 3.5 seconds of their assigned arrival time and reported that both the IM-S and RTA procedures were associated with low workload levels. In general, pilots found the IM-S concept, procedures, speeds, and interface acceptable; with 92% of pilots rating the procedures as complete and logical, 218 out of 240 responses agreeing that the IM-S speeds were acceptable, and 63% of pilots reporting that the displays were easy to understand and displayed in appropriate locations. The 22 (out of 240) responses, indicating that the commanded speeds were not acceptable and appropriate occurred during scenarios containing wind error and offset error. Concerns cited included the occurrence of multiple speed changes within a short time period, speed changes required within twenty miles of the runway, and an increase in airspeed followed shortly by a decrease in airspeed. Within this paper, appropriate design recommendations are provided, and the need for continued, iterative human-centered design is discussed.

14 CFR 91.605 - Transport category civil airplane weight limitations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... than a turbine-engine-powered airplane certificated after September 30, 1958) unless— (1) The takeoff.... (b) No person may operate a turbine-engine-powered transport category airplane certificated after... airport, the runway to be used, the effective runway gradient, the ambient temperature and wind component...

14 CFR 77.21 - Scope.

Code of Federal Regulations, 2011 CFR

2011-01-01

... of the runway. At those airports having defined strips or pathways that are used regularly for the... defined landing and takeoff area with no defined pathways for the landing and taking off of aircraft, a... and takeoff pathways. Those pathways so determined shall be considered runways and an appropriate...

75 FR 53351 - Notice of Permit Application Received Under the Antarctic Conservation Act of 1978

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-31

... adjacent to a 100m x 2000m blue-ice runway. The blue-ice runway is a natural feature that requires limited..., Suite 2, Salt Lake City, Utah 84107. Permit application No. 2011 WM-002. Nadene G. Kennedy, Permit...

Course structure-runway 28R San Francisco Airport.

DOT National Transportation Integrated Search

1973-09-01

The TSC electromagnetic scattering model is used to dtermine the expected ILS localizer performance for the planned 28R runway at San Francisco airport. It is found that the V-Ring and the 14/6 Alford array as well as the larger 22/8 Alford array ope...

F-15 ACTIVE touches down on Edwards AFB runway

NASA Image and Video Library

1998-04-14

The F-15 ACTIVE touches down on the Edwards runway following its April 14, 1998 flight. The nose is high while the canards have their rear edge raised. the aircraft's speed brake, located on the top of the aircraft behind the canopy, is also raised.

5. VIEW OF AIRFIELD LOOKING EAST FROM BUILDING 8200 (CONTROL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. VIEW OF AIRFIELD LOOKING EAST FROM BUILDING 8200 (CONTROL TOWER) SHOWING TAXIWAY B CROSSING ALPHA TAXIWAY IN FOREGROUND, ALERNATE RUNWAY (TAXIWAY J) IN MIDDLE GROUND, AND NORTH-SOUTH RUNWAY IN BACKGROUND. - Loring Air Force Base, Airfield, Central portion of base, Limestone, Aroostook County, ME

Microwave Landing System. Phase II. Tracker Error Study.

DTIC Science & Technology

1974-12-01

the runways and environs. The geographical locations of the four phototheodolite towers are indicated on Figure 1-1. A Contraves Model C phototheodolite...temperature 400 K above 500 elevation (dark sky) Side lobe location 1.720 (Ist) Type of scan Monopulse R-f transmission line Rectangular waveguide Line loss ...receiving 1.3 db Line loss transmitting 2.3 db System Facts Azimuth coverage 3600 Elevation coverage -10* to 190* (tracking -10* to 85*) Range accuracy

Comprehensive and Highly Accurate Measurements of Crane Runways, Profiles and Fastenings

PubMed Central

Dennig, Dirk; Bureick, Johannes; Link, Johannes; Diener, Dmitri; Hesse, Christian; Neumann, Ingo

2017-01-01

The process of surveying crane runways has been continually refined due to the competitive situation, modern surveying instruments, additional sensors, accessories and evaluation procedures. Guidelines, such as the International Organization for Standardization (ISO) 12488-1, define target values that must be determined by survey. For a crane runway these are for example the span, the position and height of the rails. The process has to be objective and reproducible. However, common processes of surveying crane runways do not meet these requirements sufficiently. The evaluation of the protocols, ideally by an expert, requires many years of experience. Additionally, the recording of crucial parameters, e.g., the wear of the rail, or the condition of the rail fastening and rail joints, is not regulated and for that reason are often not considered during the measurement. To solve this deficit the Advanced Rail Track Inspection System (ARTIS) was developed. ARTIS is used to measure the 3D position of crane rails, the cross-section of the crane rails, joints and, for the first time, the (crane-rail) fastenings. The system consists of a monitoring vehicle and an external tracking sensor. It makes kinematic observations with the tracking sensor from outside the rail run, e.g., the floor of an overhead crane runway, possible. In this paper we present stages of the development process of ARTIS, new target values, calibration of sensors and results of a test measurement. PMID:28505076

Earth observations taken during STS-83 mission

NASA Image and Video Library

2016-08-12

STS083-747-026 (4-8 April 1997) --- Aswan Dam and Lake Nasser along the Nile River, Egypt. The Aswan Dam controls the flow of the Nile River forming Lake Nasser. Lake Nasser is reaching relatively high water levels due to the plentiful rains since December 1996 in Kenya, near the headwaters of the Nile river. The light colored areas in the Lake are where the sun is reflecting off the surface of the water. These areas are fairly calm and not disturbed by wind gusts enabling the sunglint to show water current patterns on the surface. The Aswan runway is seen as a dark set of lines west of the Aswan Dam.

Terminal Information Processing System (TIPS) Consolidated CAB Display (CCD) Comparative Analysis.

DTIC Science & Technology

1982-04-01

Barometric pressure 3. Center field wind speed, direction and gusts 4. Runway visual range 5. Low-level wind shear 6. Vortex advisory 7. Runway equipment...PASSWORD Command (standard user) u. PAUSE Command (standard user) v. PMSG Command (standard user) w. PPD Command (standard user) x. PURGE Command (standard

78 FR 48540 - Agency Information Collection Activities: Requests for Comments; Clearance of Renewed Approval of...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-08

... collection. Background: Information to be collected will focus on pilot, controller, or vehicle driver practices and/or feedback on specific runway safety initiatives, such as training programs, Runway Safety... incursions. Respondents: An estimated 8,900 pilots, aircraft support vehicle drivers, airport/airfield...

76 FR 50809 - Notice of Availability of a Draft Environmental Assessment for a Proposed Airport Traffic Control...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-16

...) antenna and shelter with a Mark 20 or Mark 20A LOC antenna and shelter, and relocation of the Runway 25 LOC antenna array to a location 1,070 feet outward from the Runway 07 threshold, relocation of the...

Performance predictions for a parabolic localizer antenna on Runway 28R - San Francisco Airport.

DOT National Transportation Integrated Search

1973-06-01

The TSC ILS localizer model is used to predict the performance of the Texas Instruments "wide aperture" parabolic antenna as a localizer system for runway 28R at San Francisco Airport. Course derogation caused by the new American Airlines hangar is c...

78 FR 57208 - Notice of Passenger Facility Charge (PFC) Approvals and Disapprovals

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-17

... LEVEL: End of runway deicing program--phase 1, runway 34R. Taxiway S pavement reconstruction. Replace carousel 9 and oversized bag belt TU3. Terminal redevelopment program--design and associated technical... APPROVED FOR COLLECTION AND USE: PFC program administration. Design taxiways A, L and B. BRIEF DESCRIPTION...

76 FR 28123 - Notice of Passenger Facility Charge (PFC) Approvals and Disapprovals

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-13

... for Collection and Use: Design/construct passenger terminal and land/airside. PFC application... Level: Runway 16L/34R pavement rehabilitation. Concourse B--additional boarding bridges. North cargo... 16R134L. Joint seal runway 16R/34L--taxiways A and B. [[Page 28124

Improve the quality and service life of water-based pavement marking paints on pavements with high-iron aggregates.

DOT National Transportation Integrated Search

2015-08-01

White pavement paint marking on airport runways was being discolored by rust-like staining. Discoloration is a critical safety : problem because white paint indicates runways and yellow paint is used for taxiways and aircraft parking. When the white ...

6. VIEW OF AIRFIELD LOOKING SOUTHEAST FROM BUILDING 8200 (CONTROL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. VIEW OF AIRFIELD LOOKING SOUTHEAST FROM BUILDING 8200 (CONTROL TOWER SHOWING ALPHA TAXIWAY AND ALTERNATE RUNWAY (TAXIWAY J) IN FOREGROUND, NORTH-SIDE RUNWAY IN MIDDLE GROUND, AND ALERT AREA WITH ITS TAXIWAY IN BACKGROUND. - Loring Air Force Base, Airfield, Central portion of base, Limestone, Aroostook County, ME

14 CFR 151.15 - Federal-aid Airport Program: Policy affecting runway or taxiway remarking.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Federal-aid Airport Program: Policy... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AIRPORTS FEDERAL AID TO AIRPORTS General Requirements § 151.15 Federal-aid Airport Program: Policy affecting runway or taxiway remarking. No project for...

14 CFR 151.15 - Federal-aid Airport Program: Policy affecting runway or taxiway remarking.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Federal-aid Airport Program: Policy... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AIRPORTS FEDERAL AID TO AIRPORTS General Requirements § 151.15 Federal-aid Airport Program: Policy affecting runway or taxiway remarking. No project for...

14 CFR 151.15 - Federal-aid Airport Program: Policy affecting runway or taxiway remarking.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Federal-aid Airport Program: Policy... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AIRPORTS FEDERAL AID TO AIRPORTS General Requirements § 151.15 Federal-aid Airport Program: Policy affecting runway or taxiway remarking. No project for...

14 CFR 135.361 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-01-01

... distance from the point at which the obstruction clearance plane associated with the approach end of the... subpart, obstruction clearance plane means a plane sloping upward from the runway at a slope of 1:20 to... coincides with the centerline of the runway, beginning at the point where the obstruction clearance plane...

Effect of different runway size on pilot performance during simulated night landing approaches.

DOT National Transportation Integrated Search

1981-02-01

In Experiment I, three pilots flew simulated approaches and landings in a fixed-base simulator with a computer-generated-image visual display. Practice approaches were flown with an 8,000-ft-long runway that was either 75, 150, or 300 ft wide; test a...

Effects of approach lighting and variation in visible runway length on perception of approach angle simulated night landings.

DOT National Transportation Integrated Search

1982-02-01

Previous experiments have demonstrated illusions due to variations in both length and width of runways in nighttime 'black hole' approaches. Even though approach lighting is not designed to provide vertical guidance, it is possible that cues from app...

Calibration and Validation of Airborne LiDAR at McMurdo Station, Antarctica for Operation IceBridge

NASA Astrophysics Data System (ADS)

Sonntag, J. G.

2014-12-01

Airborne LiDAR flight operations based at McMurdo Station, Antarctica, present unusual challenges for calibrating and validating the sensor measurements at the level of a few centimeters. NASA's Airborne Topographic Mapper (ATM) team prefers to perform regular, near-daily calibrations of range and angular biases of our sensor for the lengthy field deployments typical for Operation IceBridge (OIB). For the fall 2013 OIB deployment to McMurdo, we had to adapt our usual technique of regular overflights of an independently-surveyed airport parking ramp to deal with the fact that the McMurdo airfield was located on tidally-influenced sea ice, and that very few nearby durable surfaces were free of variable-depth snow during the OIB deployment. We detail our approach for dealing with these challenges, which included multiple GPS/vehicle surveys of the sea ice runway to quantify surface changes due to grooming operations, combined with GPS tide-gauge measurements of the runway's tidal motion. We also conducted a remote GPS/vehicle survey of a mostly snow-free road on Black Island, and included both sites during near-daily overflights with the ATM. We discuss the quantitative results of these surveys and the associated ATM overflights, and present conclusions for future deployments. Finally we discuss a related validation effort in which we compare ATM results from overflights of snow-free areas in the Dry Valleys with ATM surveys of the same area from a 2001 effort there.

The impact of airport characteristics on airport surface accidents and incidents.

PubMed

Wilke, Sabine; Majumdar, Arnab; Ochieng, Washington Y

2015-06-01

Airport surface safety and in particular runway and taxiway safety is acknowledged globally as one of aviation's greatest challenges. To improve this key area of aviation safety, it is necessary to identify and understand the causal and contributing factors on safety occurrences. While the contribution of human factors, operations, and procedures has been researched extensively, the impact of the airport and its associated characteristics itself has received little or no attention. This paper introduces a novel methodology for risk and hazard assessment of airport surface operations, and models the relationships between airport characteristics, and (a) the rate of occurrences, (b) the severity of occurrences, and (c) the causal factors underlying occurrences. The results show for the first time how the characteristics of airports, and in particular its infrastructure and operations, influence the safety of surface operations. Copyright © 2015 Elsevier Ltd. and National Safety Council. Published by Elsevier Ltd. All rights reserved.

KSC-2013-1788

NASA Image and Video Library

2013-03-08

CAPE CANAVERAL, Fla. – At Kennedy Space Center's Shuttle Landing Facility, a granite plaque marks the spot where space shuttle Atlantis' nose gear came to a stop at the conclusion of STS-135, the final flight of the Space Shuttle Program. Permanent reminders indicate where on the runway the orbiters Discovery, Endeavour and Atlantis stopped rolling as each finished its last mission in 2011. In addition to the granite markers, which are installed alongside the runway, there are etchings in the grooved concrete along the runway's centerline to mark each wheelstop. The etchings and markers were created and installed by local artist Chad Stout of C Spray Glass Blasting in Cocoa, Fla. Photo credit: NASA/Tim Jacobs

KSC-2013-1790

NASA Image and Video Library

2013-03-08

CAPE CANAVERAL, Fla. – At Kennedy Space Center's Shuttle Landing Facility, a granite plaque marks the spot where space shuttle Discovery's nose gear came to a stop at the conclusion of STS-133, the final flight of the Space Shuttle Program. Permanent reminders indicate where on the runway the orbiters Discovery, Endeavour and Atlantis stopped rolling as each finished its last mission in 2011. In addition to the granite markers, which are installed alongside the runway, there are etchings in the grooved concrete along the runway's centerline to mark each wheelstop. The etchings and markers were created and installed by local artist Chad Stout of C Spray Glass Blasting in Cocoa, Fla. Photo credit: NASA/Tim Jacobs

KSC-2013-1789

NASA Image and Video Library

2013-03-08

CAPE CANAVERAL, Fla. – At Kennedy Space Center's Shuttle Landing Facility, a granite plaque marks the spot where space shuttle Endeavour's nose gear came to a stop at the conclusion of STS-134, the final flight of the Space Shuttle Program. Permanent reminders indicate where on the runway the orbiters Discovery, Endeavour and Atlantis stopped rolling as each finished its last mission in 2011. In addition to the granite markers, which are installed alongside the runway, there are etchings in the grooved concrete along the runway's centerline to mark each wheelstop. The etchings and markers were created and installed by local artist Chad Stout of C Spray Glass Blasting in Cocoa, Fla. Photo credit: NASA/Tim Jacobs

High Speed Prototype Car Test

NASA Image and Video Library

2014-01-10

CAPE CANAVERAL, Fla. - The Performance Power Racing and Hennessey Performance teams pose with a Hennessey Venom GT at the 3.5-mile long runway at the Shuttle Landing Facility at NASA's Kennedy Space Center in Florida. The teams are, from left, Hennessey's John Heinricy, John Hennessey, Brian Smith, Performance Power Racing's Johnny Bohmer, Matt Lundy and Jeff McEachran. The flat concrete runway is one of the few places in the world where high performance automobiles can be tested for aerodynamic and safety designs. Hennessey Performance of Sealy, Texas, worked with Performance Power Racing in West Palm Beach to arrange use of the NASA facility. Performance Power Racing has conducted numerous engineering tests on the runway with a variety of vehicles.

3. Credit USAF, ca. 1945. Original housed in the Records ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. Credit USAF, ca. 1945. Original housed in the Records of the Defense Intelligence Agency. Record Group 373. National Archives. Cartographic and Architectural Branch. Washington, D.C. Aerial orthophoto map 16PS5M79-IV23 of Muroc Flight Test Base (North Base), north faces up with runway at the top and Rogers Dry Lake at the lower right. Ammunition huts (not extant in 1995) appear in a cluster just south of the west end of the runway. Note runway markings on lakebed. Linear feature at very top of image is rocket sled test track designed and built 1944-1945. - Edwards Air Force Base, North Base, North Base Road, Boron, Kern County, CA

NASA Research For Instrument Approaches To Closely Spaced Parallel Runways

NASA Technical Reports Server (NTRS)

Elliott, Dawn M.; Perry, R. Brad

2000-01-01

Within the NASA Aviation Systems Capacity Program, the Terminal Area Productivity (TAP) Project is addressing airport capacity enhancements during instrument meteorological condition (IMC). The Airborne Information for Lateral Spacing (AILS) research within TAP has focused on an airborne centered approach for independent instrument approaches to closely spaced parallel runways using Differential Global Positioning System (DGPS) and Automatic Dependent Surveillance-Broadcast (ADS-B) technologies. NASA Langley Research Center (LaRC), working in partnership with Honeywell, Inc., completed in AILS simulation study, flight test, and demonstration in 1999 examining normal approaches and potential collision scenarios to runways with separation distances of 3,400 and 2,500 feet. The results of the flight test and demonstration validate the simulation study.

KSC-07pd0909

NASA Image and Video Library

2007-04-17

KENNEDY SPACE CENTER, FLA. -- On the KSC Shuttle Landing Facility, the Starfighter F-104 starts to taxi to the runway. The pilot is Rick Svetkoff; the co-pilot is Dave Waldrop. The aircraft is taking part in a series of pathfinder test missions from the space shuttle runway. Two flights will generate test data to validate sonic boom assumptions about the potential impacts of suborbital and orbital commercial spaceflight from the facility. NASA is assessing the environmental impact of such flights. Starfighters Inc. of Clearwater, Fla., will perform the flights to help in assessing suborbital space launch trajectories from the runway and paving the way for future commercial space tourism and research flights from the facility. Photo credit: NASA/Kim Shiflett

KSC-07pd0910

NASA Image and Video Library

2007-04-17

KENNEDY SPACE CENTER, FLA. -- From the KSC Shuttle Landing Facility, the Starfighter F-104 picks up speed on the runway for takeoff. The pilot is Rick Svetkoff; the co-pilot is Dave Waldrop. The aircraft is taking part in a series of pathfinder test missions from the space shuttle runway. Two flights will generate test data to validate sonic boom assumptions about the potential impacts of suborbital and orbital commercial spaceflight from the facility. NASA is assessing the environmental impact of such flights. Starfighters Inc. of Clearwater, Fla., will perform the flights to help in assessing suborbital space launch trajectories from the runway and paving the way for future commercial space tourism and research flights from the facility. Photo credit: NASA/Kim Shiflett

Behavior of aircraft antiskid braking systems on dry and wet runway surfaces: Hydromechanically controlled system

NASA Technical Reports Server (NTRS)

Tanner, J. A.; Stubbs, S. M.; Smith, E. G.

1981-01-01

The investigation utilized one main gear wheel, brake, and tire assembly of a McDonnell Douglas DC-9 series 10 airplane. The landing-gear strut was replaced by a dynamometer. During maximum braking, average braking behavior indexes based upon brake pressure, brake torque, and drag-force friction coefficient developed by the antiskid system were generally higher on dry surfaces than on wet surfaces. The three braking behavior indexes gave similar results but should not be used interchangeably as a measure of the braking of this antiskid sytem. During the transition from a dry to a flooded surface under heavy braking, the wheel entered into a deep skid but the antiskid system reacted quickly by reducing brake pressure and performed normally during the remainder of the run on the flooded surface. The brake-pressure recovery following transition from a flooded to a dry surface was shown to be a function of the antiskid modulating orifice.

Development of the Runway Incursion Advisory and Alerting System (RIAAS): Research Summary

NASA Technical Reports Server (NTRS)

Jones, Denise R. (Technical Monitor); Cassell, Rick

2005-01-01

This report summarizes research conducted on an aircraft based Runway Incursion Advisory and Alerting System (RIAAS) developed under a cooperative agreement between Rannoch Corporation and the NASA Langley Research Center. A summary of RIAAS is presented along with results from simulation and flight testing, safety benefits, and key technical issues.

Visibility Variability at Seattle, WA and Portland, OR : Insights into the Impacts of Runway Visual Range (RVR) Measurements on Aviation Operations.

DOT National Transportation Integrated Search

2001-01-14

The FAA's new generation Runway Visual Range (RVR) : system was first placed into service in 1994 at several : key airports in the United States. During the last three : years, the Volpe National Transportation Systems Center : has monitored RVR data...

Construction, maintenance, and operation of a glacial runway : McMurdo Station, Antarctica

DOT National Transportation Integrated Search

1998-03-01

On February 7, 1994, a C-141 departed Christchurch, New Zealand, and landed on the 3050-m (10,000-ft) Pegasus glacial ice runway, located on the Ross Ice Shelf 13 km (8 mi) south of McMurdo, Antarctica. This event marked the final test for a five-yea...

STS-49 Endeavour, OV-105, landing on concrete runway 22 at EAFB, California

NASA Technical Reports Server (NTRS)

1992-01-01

STS-49 Endeavour, Orbiter Vehicle (OV) 105, glides above concrete runway 22 at Edwards Air Force Base (EAFB), California, just before main landing gear (MLG) touchdown. Nose landing gear (NLG) is also deployed during the landing sequence. Landing occurred at 1:36:38 pm (Pacific Daylight Time (PDT)).

STS-33 Discovery, OV-103, approaches concrete runway 04 at EAFB, California

NASA Technical Reports Server (NTRS)

1989-01-01

STS-33 Discovery, Orbiter Vehicle (OV) 103, approaches runway 04 at Edwards Air Force Base (EAFB), California. OV-103 with landing gear deployed is silhouetted against the orange sky of a sunset as it glides over the mountains. The landing occurred at 16:31:02 pm Pacific Standard Time (PST).

Aircraft and avionic related research required to develop an effective high-speed runway exit system

NASA Technical Reports Server (NTRS)

Schoen, M. L.; Hosford, J. E.; Graham, J. M., Jr.; Preston, O. W.; Frankel, R. S.; Erickson, J. B.

1979-01-01

Research was conducted to increase airport capacity by studying the feasibility of the longitudinal separation between aircraft sequences on final approach. The multidisciplinary factors which include the utility of high speed exits for efficient runway operations were described along with recommendations and highlights of these studies.

77 FR 64836 - Notice of Availability of Draft Environmental Impact Statement (DEIS), Draft Section 4(f...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-23

... DEIS for Proposed Runway Safety Area Improvements at the Kodiak Airport, Kodiak, AK AGENCY: Federal... advise the public that a Draft Environmental Impact Statement (DEIS) for proposed Runway Safety Area... the DEIS can be submitted to the individual listed in the section, FOR FURTHER INFORMATION CONTACT. A...

78 FR 76383 - Notice of Passenger Facility Charge (PFC) Approvals and Disapprovals

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-17

...: LGA runways 4 and 31 runway safety area planning, environmental, and engineering. Brief Description of... Collection at EWR and Use at JFK at a $3.00 PFC Level: JFK taxiway P rehabilitation planning and engineering... delay reduction phase II--planning and engineering. Brief Description of Project Approved for Collection...

Ground winds for Kennedy Space Center, Florida (1978 version)

NASA Technical Reports Server (NTRS)

Johnson, D. L.; Brown, S. C.

1978-01-01

Ground level runway wind statistics are presented for the Kennedy Space Center, Florida area. Crosswind, headwind, tailwind, and headwind reversal percentage frequencies are given with respect to month and hour for the Kennedy Space Center Space Shuttle runway. This document supersedes NASA CR-128995 and should be used in place of it.

Upgraded FAA Airfield Capacity Model. Volume 2. Technical Description of Revisions

DTIC Science & Technology

1981-02-01

the threshold t k a the time at which departure k is released FIGURE 3-1 TIME AXIS DIAGRAM OF SINGLE RUNWAY OPERATIONS 3-2 J"- SIGMAR the standard...standard deviation of the interarrival time. SIGMAR - the standard deviation of the arrival runway occupancy time. A-5 SINGLE - program subroutine for

STS-111 commander, Ken Cockrell, greets dignitaries and recovery technicians on the runway at Edward

NASA Technical Reports Server (NTRS)

2002-01-01

STS-111 commander Ken Cockrell greets dignitaries and recovery technicians on the runway at Edwards Air Force Base following the landing of the space shuttle Endeavour on June 19, 2002. Behind Cockrell are (from left) mission specialists Philippe Perrin and Franklin Chang-Diaz and Shuttle pilot Paul Lockhart.

Fast-Time Evaluations of Airborne Merging and Spacing in Terminal Arrival Operations

NASA Technical Reports Server (NTRS)

Krishnamurthy, Karthik; Barmore, Bryan; Bussink, Frank; Weitz, Lesley; Dahlene, Laura

2005-01-01

NASA researchers are developing new airborne technologies and procedures to increase runway throughput at capacity-constrained airports by improving the precision of inter-arrival spacing at the runway threshold. In this new operational concept, pilots of equipped aircraft are cleared to adjust aircraft speed to achieve a designated spacing interval at the runway threshold, relative to a designated lead aircraft. A new airborne toolset, prototypes of which are being developed at the NASA Langley Research Center, assists pilots in achieving this objective. The current prototype allows precision spacing operations to commence even when the aircraft and its lead are not yet in-trail, but are on merging arrival routes to the runway. A series of fast-time evaluations of the new toolset were conducted at the Langley Research Center during the summer of 2004. The study assessed toolset performance in a mixed fleet of aircraft on three merging arrival streams under a range of operating conditions. The results of the study indicate that the prototype possesses a high degree of robustness to moderate variations in operating conditions.

Design of AC - 25 asphalt mixture proportioning on the taxiway of Shenzhen Baoan International Airport

NASA Astrophysics Data System (ADS)

Tian, Shuaituan; Ye, Song; Luo, Min

2017-12-01

According to the growing demand for air transport industry, an extension of the associated taxiway is required, so the Shenzhen Airport runway west of the taxiway expansion is imperative. Combined with the taxiway of Shenzhen Baoan International Airport, we design the lower layer type of AC-25 modified asphalt mixture ratio. We analysis from raw material selection, mixture gradation design and admixture added, and finally choose the excellent performance of asphalt mixture.

Water-Compatible Polymer Concrete Materials for use in Rapid Repair Systems for Airport Runways

DTIC Science & Technology

1981-03-01

resin systems, resorcinol phenol- formaldehyde (RPF), urea - formaldehyde (UF), melamine - formaldehyde (MF), and furfuryl alcohol (FA), were selected for...type polymer systems. Phenol- formaldehyde (PF), melamine - formaldehyde (MF), urea -formalde- hyde (UF), and furfuryl alcohol (FA) monomers contain OH and...1-1.5) (1-2) Urea - formaldehyde NH2 CONH2 - HCHO Liquid 7150 (1.0) (1.5-2.5) Melamine - formaldehyde NH2 C:NC(NH2 ):NC(N’H2

Motivational effects of methamphetamine as measured by the runway method using priming stimulation of intracranial self-stimulation behavior.

PubMed

Sagara, Hidenori; Kitamura, Yoshihisa; Sendo, Toshiaki; Araki, Hiroaki; Gomita, Yutaka

2008-04-01

Priming stimulation is known to promote the motivational effects of intracranial self-stimulation (ICSS) behavior. The runway method using priming stimulation can experimentally distinguish the reward and motivational effects of ICSS behavior. In this study, we examined the motivational effect of a drug as determined by the runway method using priming stimulation of ICSS behavior. Electrodes were implanted chronically into the medial forebrain bundle (MFB) of the rats. A lever for stimulation of the MFB was set on the opposite side of the start box in the apparatus. The rats were trained to obtain a reward stimulation (50-200 muA, 0.2 ms, 60 Hz) of the MFB by pressing the goal lever, and then priming stimulation of the MFB was applied. After priming stimulation, rats were placed in the start box of the runway apparatus and the time taken by the rat to press the lever was recorded. Priming stimulation frequency was significantly correlated with running speed (r=0.897, p<0.05). Methamphetamine (1, 3 mg/kg) induced an increase in running speed (F(3, 20)=16.257, p<0.01), and was further increased with increase in priming stimulation frequency. In addition, methamphetamine significantly enhanced the motivational effect. These results suggest that the runway method using priming stimulation of ICSS behavior may be an effective way to evaluate the enhancing effect of a drug on motivation.

Comparison of Different Control Schemes for Strategic Departure Metering

NASA Technical Reports Server (NTRS)

Idris, Husni; Shen, Ni; Saraf, Aditya; Bertino, Jason; Zelinski, Shannon

2016-01-01

Airports and their terminal airspaces are key choke points in the air transportation system causing major delays and adding to pollution. A solution aimed at mitigating these chokepoints integrates the scheduling of runway operations, flight release from the gates and ramp into the airport movement area, and merging with other traffic competing for downstream airspace points. Within this integrated concept, we present a simulation-based analysis of the departure metering process, which delays the release of flights into the airport movement area while balancing two competing objectives: (1) maintaining large enough queues at the airport resources to maximize throughput and (2) absorbing excess delays at the gates or in ramp areas to save on fuel consumption, emissions, noise, and passenger discomfort. Three metering strategies are compared which respectively attempt to control the number of flights that (1) left the gate but did not take off, (2) left the ramp but did not take off, and (3) spent their unimpeded transit time to the runway but did not take off. It was observed that under deterministic and demand uncertainty conditions, the first strategy performed better than the other two strategies in terms of maintaining the runway throughput while transferring a significant average delay of two minutes to the gate. On the other hand, under uncertainties of flight transit time and runway service rate, all the strategies struggled to delay flights at the gate without a significant impact on the runway throughput.

Information Requirements for Supervisory Air Traffic Controllers in Support of a Wake Vortex Departure System

NASA Technical Reports Server (NTRS)

Lohr, Gary W.; Williams, Daniel M.; Trujillo, Anna C.

2008-01-01

Closely Space Parallel Runway (CSPR) configurations are capacity limited for departures due to the requirement to apply wake vortex separation standards from traffic departing on the adjacent parallel runway. To mitigate the effects of this constraint, a concept focusing on wind dependent departure operations has been developed, known as the Wake Turbulence Mitigation for Departures (WTMD). This concept takes advantage of the fact that crosswinds of sufficient velocity blow wakes generated by aircraft departing from the downwind runway away from the upwind runway. Consequently, under certain conditions, wake separations on the upwind runway would not be required based on wakes generated by aircraft on the downwind runway, as is currently the case. It follows that information requirements, and sources for this information, would need to be determined for airport traffic control tower (ATCT) supervisory personnel who would be charged with decisions regarding use of the procedure. To determine the information requirements, data were collected from ATCT supervisors and controller-in-charge qualified individuals at Lambert-St. Louis International Airport (STL) and George Bush Houston Intercontinental Airport (IAH). STL and IAH were chosen as data collection sites based on the implementation of a WTMD prototype system, operating in shadow mode, at these locations. The 17 total subjects (STL: 5, IAH: 12) represented a broad-base of air traffic experience. Results indicated that the following information was required to support the conduct of WTMD operations: current and forecast weather information, current and forecast traffic demand and traffic flow restrictions, and WTMD System status information and alerting. Subjects further indicated that the requisite information is currently available in the tower cab with the exception of the WTMD status and alerting. Subjects were given a demonstration of a display supporting the prototype systems and unanimously stated that the WTMD status information they felt important was represented. Overwhelmingly, subjects felt that approving, monitoring and terminating the WTMD procedure could be integrated into their supervisory workload.

Calculation of Flight Deck Interval Management Assigned Spacing Goals Subject to Multiple Scheduling Constraints

NASA Technical Reports Server (NTRS)

Robinson, John E.

2014-01-01

The Federal Aviation Administration's Next Generation Air Transportation System will combine advanced air traffic management technologies, performance-based procedures, and state-of-the-art avionics to maintain efficient operations throughout the entire arrival phase of flight. Flight deck Interval Management (FIM) operations are expected to use sophisticated airborne spacing capabilities to meet precise in-trail spacing from top-of-descent to touchdown. Recent human-in-the-loop simulations by the National Aeronautics and Space Administration have found that selection of the assigned spacing goal using the runway schedule can lead to premature interruptions of the FIM operation during periods of high traffic demand. This study compares three methods for calculating the assigned spacing goal for a FIM operation that is also subject to time-based metering constraints. The particular paradigms investigated include: one based upon the desired runway spacing interval, one based upon the desired meter fix spacing interval, and a composite method that combines both intervals. These three paradigms are evaluated for the primary arrival procedures to Phoenix Sky Harbor International Airport using the entire set of Rapid Update Cycle wind forecasts from 2011. For typical meter fix and runway spacing intervals, the runway- and meter fix-based paradigms exhibit moderate FIM interruption rates due to their inability to consider multiple metering constraints. The addition of larger separation buffers decreases the FIM interruption rate but also significantly reduces the achievable runway throughput. The composite paradigm causes no FIM interruptions, and maintains higher runway throughput more often than the other paradigms. A key implication of the results with respect to time-based metering is that FIM operations using a single assigned spacing goal will not allow reduction of the arrival schedule's excess spacing buffer. Alternative solutions for conducting the FIM operation in a manner more compatible with the arrival schedule are discussed in detail.

NextGen Operations in a Simulated NY Area Airspace

NASA Technical Reports Server (NTRS)

Smith, Nancy M.; Parke, Bonny; Lee, Paul; Homola, Jeff; Brasil, Connie; Buckley, Nathan; Cabrall, Chris; Chevalley, Eric; Lin, Cindy; Morey, Susan;

Review of NASA antiskid braking research

NASA Technical Reports Server (NTRS)

Tanner, J. A.

1982-01-01

NASA antiskid braking system research programs are reviewed. These programs include experimental studies of four antiskid systems on the Langley Landing Loads Track, flights tests with a DC-9 airplane, and computer simulation studies. Results from these research efforts include identification of factors contributing to degraded antiskid performance under adverse weather conditions, tire tread temperature measurements during antiskid braking on dry runway surfaces, and an assessment of the accuracy of various brake pressure-torque computer models. This information should lead to the development of better antiskid systems in the future.

Modifying and Testing ATC Controller Interface (CI) for Data Link Clearances

NASA Technical Reports Server (NTRS)

2001-01-01

The Controller-Pilot Data Link Communications (CPDLC) and Air Traffic Control workstation research was conducted as part of the 1997 NASA Low Visibility Landing and Surface Operations (LVLASO) demonstration program at Atlanta Hartsfield airport. Research activity under this grant increased the sophistication of the Controllers' Communication and Situational Awareness Terminal (C-CAST) and developed a VHF Data Link -Mode 2 communications platform. The research culminated with participation in the 2000 NASA Aviation Safety Program's Synthetic Vision System (SVS) / Runway Incursion Prevention System (RIPS) flight demonstration at Dallas-Fort Worth Airport.

Surveillance of ground vehicles for airport security

NASA Astrophysics Data System (ADS)

Blasch, Erik; Wang, Zhonghai; Shen, Dan; Ling, Haibin; Chen, Genshe

2014-06-01

Future surveillance systems will work in complex and cluttered environments which require systems engineering solutions for such applications such as airport ground surface management. In this paper, we highlight the use of a L1 video tracker for monitoring activities at an airport. We present methods of information fusion, entity detection, and activity analysis using airport videos for runway detection and airport terminal events. For coordinated airport security, automated ground surveillance enhances efficient and safe maneuvers for aircraft, unmanned air vehicles (UAVs) and unmanned ground vehicles (UGVs) operating within airport environments.

Crew emergency return vehicle autoland feasibility study

NASA Technical Reports Server (NTRS)

Bossi, J. A.; Langehough, M. A.; Lee, K. L.

1989-01-01

The crew emergency return vehicle (CERV) autoland feasibility study focused on determining the controllability of the NASA Langley high lift over drag CERV for performing an automatic landing at a prescribed runway. An autoland system was developed using integral linear quadratic Gaussian (LQG) design techniques. The design was verified using a nonlinear 6 DOF simulation. Simulation results demonstrate that the CERV configuration is a very flyable configuration for performing an autoland mission. Adequate stability and control was demonstrated for wind turbulence and wind shear. Control surface actuator requirements were developed.

Blood lead level and types of aviation fuel in aircraft maintenance crew.

PubMed

Park, Won-Ju; Gu, Hye-Min; Lee, Suk-Ho

2013-10-01

This study inquired into any significant difference in blood lead levels (BLLs) among aircraft maintenance crews at the air-bases, each with a different aviation fuel in use, and confirmed an environmental impact of leaded aviation gasoline (AVGAS). This study included a total of 256 male aircraft maintenance personnel, among whom 105 used only AVGAS as their aviation fuel, while 151 used only jet propellant 8 (JP-8), a kerosene variety. BLLs were measured and the data on related factors were obtained. The arithmetic and geometric means of BLLs of the personnel at the airbases that used only AVGAS were 4.20 microg x dl(-1) and 4.01 microg x dl(-1) and that used only JP-8 were 3.79 microg x dl(-1) and 3.57 microg x dl(-1), respectively. The BLLs of the maintenance crew of the main workspace that was located within a 200-m distance from the runway were higher than those of the main workspace that was located 200 m or farther from the runway. The longer the work hours in the runway or the longer the work duration, the higher the BLLs of the maintenance crew. This investigation exposed the fact that a body's BLL could be increased by AVGAS emissions through the examination of aircraft maintenance crew. This result is in agreement with results of previous studies that suggest proximity to an airport may be associated with elevated BLLs for adults and children. Collectively, the results of the current study and previous research suggest that long-duration inhabitation and/or activities in close proximity to an air facility should be limited given that lead poses known health risks.

Effects of Scenery, Lighting, Glideslope, and Experience on Timing the Landing Flare

ERIC Educational Resources Information Center

Palmisano, Stephen; Favelle, Simone; Sachtler, W. L.

2008-01-01

This study examined three visual strategies for timing the initiation of the landing flare based on perceptions of either: (a) a critical height above ground level; (b) a critical runway width angle ([psi]); or (c) a critical time-to-contact (TTC) with the runway. Visual displays simulated landing approaches with trial-to-trial variations in…

Aircraft accident report : runway overrun during landing American Airlines Flight 1420, McDonnell Douglas MD-82, N215AA, Little Rock, Arkansas, June 1, 1999

DOT National Transportation Integrated Search

2001-10-23

This report explains the accident involving American Airlines flight 1420, a McDonnell : Douglas MD-82, which crashed after it overran the end of runway 4R during landing at Little Rock : National Airport in Little Rock, Arkansas. Safety issues discu...

Upgraded FAA Airfield Capacity Model. Volume 1. Supplemental User’s Guide

DTIC Science & Technology

1981-02-01

SIGMAR (P4.0) cc 1-4 -standard deviation, in seconds, of arrival runway occupancy time (R.O.T.). SIGMAA (F4.0) cc 5-8 -standard deviation, in seconds...iI SI GMAC - The standard deviation of the time from departure clearance to start of roll. SIGMAR - The standard deviation of the arrival runway

Preliminary test results of the joint FAA-USAF-NASA runway research program. Part 1: Traction measurements of several runways under wet and dry conditions with a Boeing 727, a diagonal-braked vehicle, and a mu-meter

NASA Technical Reports Server (NTRS)

Horne, W. B.; Yager, T. J.; Sleeper, R. K.; Merritt, L. R.

1977-01-01

The stopping distance, brake application velocity, and time of brake application were measured for two modern jet transports, along with the NASA diagonal-braked vehicle and the British Mu-Meter on several runways, which when wetted, cover the range of slipperiness likely to be encountered in the United States. Tests were designed to determine if correlation between the aircraft and friction measuring vehicles exists. The test procedure, data reduction techniques, and preliminary test results obtained with the Boeing 727, the Douglas DC-9, and the ground vehicles are given. Time histories of the aircraft test run parameters are included.