Frictional interactions in forming processes: New studies with transparent sapphire strip-drawing dies

NASA Astrophysics Data System (ADS)

Rao, R. S.; Lu, C. Y.; Wright, P. K.; Devenpeck, M. L.; Richmond, O.; Appleby, E. J.

1982-05-01

This research is concerned with the frictional interactions at the toolwork interfaces in the machining and strip-drawing processes. A novel feature is that transparent sapphire (single crystal Al2O3) is being used as the tool and die material. This allows the tribological features of the interface to be directly observed and recorded on movie-film. These qualitative studies provide information on the role of lubricants. In addition, techniques are being developed to quantify the velocity gradient along the interface. For example, in the drawing work it has been found that tracer markings (e.g. dye-spots), applied to the undrawn strip, remain intact during drawing and can be tracked along the sapphire/strip interface. Such data will be used as input to a finite-element, elasto-plastic-workhardening model of the deformation process. The latter can compute strip deformation characteristics, drawing forces and local coefficients of friction at the interface. Introductory results will be presented in this paper, obtained from drawing tin-plated mild steel with sapphire and cemented carbide dies. Drawing loads and die-separating forces will be presented and movie-films of the action of tracer markings at the interface shown. In order to demonstrate how this data can be used in an analysis of a large strain deformation process with friction, initial results from running the FIPDEF elasto-plastic code will be discussed. From a commercial viewpoint research on strip-drawing is of special interest to the can-making industry. From a physical viewpoint stripdrawing is of particular interest because it is a symmetrical, plane strain deformation and, in comparison with other metal processing operations, it is more readily modeled. However, until now the elasto-plastic codes that have been developed to predictively model drawing have had limitations: the most notable being that of quantifying the friction conditions at the die-work interface. Hence the specification of the

Modeling of microstructure evolution of magnesium alloy during the high pressure die casting process

NASA Astrophysics Data System (ADS)

Wu, Mengwu; Xiong, Shoumei

2012-07-01

Two important microstructure characteristics of high pressure die cast magnesium alloy are the externally solidified crystals (ESCs) and the fully divorced eutectic which form at the filling stage of the shot sleeve and at the last stage of solidification in the die cavity, respectively. Both of them have a significant influence on the mechanical properties and performance of magnesium alloy die castings. In the present paper, a numerical model based on the cellular automaton (CA) method was developed to simulate the microstructure evolution of magnesium alloy during cold-chamber high pressure die casting (HPDC) process. Modeling of dendritic growth of magnesium alloy with six-fold symmetry was achieved by defining a special neighbourhood configuration and calculating of the growth kinetics from complete solution of the transport equations. Special attention was paid to establish a nucleation model considering both of the nucleation of externally solidified crystals in the shot sleeve and the massive nucleation in the die cavity. Meanwhile, simulation of the formation of fully divorced eutectic was also taken into account in the present CA model. Validation was performed and the capability of the present model was addressed by comparing the simulated results with those obtained by experiments.

Die singulation method

DOEpatents

Swiler, Thomas P.; Garcia, Ernest J.; Francis, Kathryn M.

2013-06-11

A method is disclosed for singulating die from a semiconductor substrate (e.g. a semiconductor-on-insulator substrate or a bulk silicon substrate) containing an oxide layer (e.g. silicon dioxide or a silicate glass) and one or more semiconductor layers (e.g. monocrystalline or polycrystalline silicon) located above the oxide layer. The method etches trenches through the substrate and through each semiconductor layer about the die being singulated, with the trenches being offset from each other around at least a part of the die so that the oxide layer between the trenches holds the substrate and die together. The trenches can be anisotropically etched using a Deep Reactive Ion Etching (DRIE) process. After the trenches are etched, the oxide layer between the trenches can be etched away with an HF etchant to singulate the die. A release fixture can be located near one side of the substrate to receive the singulated die.

Die singulation method

DOEpatents

Swiler, Thomas P [Albuquerque, NM; Garcia, Ernest J [Albuquerque, NM; Francis, Kathryn M [Rio Rancho, NM

2014-01-07

A method is disclosed for singulating die from a semiconductor substrate (e.g. a semiconductor-on-insulator substrate or a bulk silicon substrate) containing an oxide layer (e.g. silicon dioxide or a silicate glass) and one or more semiconductor layers (e.g. monocrystalline or polycrystalline silicon) located above the oxide layer. The method etches trenches through the substrate and through each semiconductor layer about the die being singulated, with the trenches being offset from each other around at least a part of the die so that the oxide layer between the trenches holds the substrate and die together. The trenches can be anisotropically etched using a Deep Reactive Ion Etching (DRIE) process. After the trenches are etched, the oxide layer between the trenches can be etched away with a HF etchant to singulate the die. A release fixture can be located near one side of the substrate to receive the singulated die.

Optimization of process parameters in the RF-DC plasma N2-H2 for AISI420 molds and dies

NASA Astrophysics Data System (ADS)

Herdianto, Hengky; Djoko, D. J.; Santjojo, H.; Masruroh

2017-11-01

The RF-DC plasma N2-H2 was used to make precise AISI420 molds and dies have complex textured geometry. The quality of the molds and dies directly affect the quality of the produced parts. The excellent examples of molds were used for injection molding lenses and dies used for the precision forging of automotive drive train components. In this study, a temperature, DC bias, and duration as process parameters of the RF-DC plasma N2-H2 have been optimized for molds and dies fabrication. The mask-less micro-patterned method was utilized to draw the initial 2D micro patterns directly onto the AISI420 substrate surface. The unprinted substrate surfaces were selectively nitrided by the RF-DC plasma N2-H2 at 673 K for 5400 s by 70 Pa with hollow cathode device. Energy Dispersive X-ray was utilized to describe the nitrogen content distribution at the vicinity of the border between the unprinted surfaces. This exclusive nitrogen mapping proves that only the unprinted parts of the substrate have high content nitrogen solutes. XRD analysis was performed to investigate whether the iron nitrides were precipitated by RF-DC plasma N2-H2 in the AISI420.

Pultrusion Die Assembly

NASA Technical Reports Server (NTRS)

Wilson, Maywood L. (Inventor); Johnson, Gary S. (Inventor); Frye, Mark W. (Inventor); Stanfield, Clarence E. (Inventor)

1988-01-01

This invention relates generally to pultrusion die assemblies, and more particularly, to a pultrusion die assembly which incorporates a plurality of functions in order to produce a continuous, thin composite fiber reinforced thermoplastic material. The invention is useful for making high performance thermoplastic composite materials in sheets which can be coiled on a spool and stored for further processing.

The study of flow pattern and phase-change problem in die casting process

NASA Technical Reports Server (NTRS)

Wang, T. S.; Wei, H.; Chen, Y. S.; Shang, H. M.

1996-01-01

The flow pattern and solidification phenomena in die casting process have been investigated in the first phase study. The flow pattern in filling process is predicted by using a VOF (volume of fluid) method. A good agreement with experimental observation is obtained for filling the water into a die cavity with different gate geometry and with an obstacle in the cavity. An enthalpy method has been applied to solve the solidification problem. By treating the latent heat implicitly into the enthalpy instead of explicitly into the source term, the CPU time can be reduced at least 20 times. The effect of material properties on solidification fronts is tested. It concludes that the dependence of properties on temperature is significant. The influence of the natural convection over the diffusion has also been studied. The result shows that the liquid metal solidification phenomena is diffusion dominant, and the natural convection can affect the shape of the interface. In the second phase study, the filling and solidification processes will be considered simultaneously.

Process research into metallic pipe wear of hot chamber die casting machines and methods ofincreasing wear resistance

NASA Astrophysics Data System (ADS)

Mukhametzyanova, G. F.; Kolesnikov, MS; Mukhametzyanov, I. R.; Astatshenko, V. I.

2017-09-01

The kinetics and reasons for metallic pipe wear of hot chamberzinc alloy die casting machines are established.Increasing metallic pipe wear components wear resistance is being achieved by means of die steelДИ - 22 with electroslag remelting modification and electron-beamremelting modification and after the processes of nitriding and boriding besides.

Sputtered protective coatings for die casting dies

NASA Technical Reports Server (NTRS)

Mirtich, M. J.; Nieh, C.-Y.; Wallace, J. F.

1981-01-01

Three experimental research designs investigating candidate materials and processes involved in protective die surface coating procedures by sputter deposition, using ion beam technologies, are discussed. Various pre-test results show that none of the coatings remained completely intact for 15,000 test cycles. The longest lifetime was observed for coatings such as tungsten, platinum, and molybdenum which reduced thermal fatigue, but exhibited oxidation and suppressed crack initiation only as long as the coating did not fracture. Final test results confirmed earlier findings and coatings with Pt and W proved to be the candidate materials to be used on a die surface to increase die life. In the W-coated specimens, which remained intact on the surface after thermal fatigue testing, no oxidation was found under the coating, although a few cracks formed on the surface where the coating broke down. Further research is planned.

Nursing care of patients during the dying process: a painful professional and human function.

PubMed

Lopera Betancur, Martha Adiela

2015-01-01

This work sought to describe the care functions of nurses with patients during the dying process. This was a qualitative study with ethnographic approach stemming from the analysis of the culture of nurses; it was conducted in the city of Medellín, Colombia. Theoretical saturation was obtained with 23 interviews. Nurses feel the duty to care for patients throughout the vital cycle through functions defined as: serving, helping, accompanying, offering support, advocating, educating, and representing, which they identify as indispensable. They also perceive as their own the social responsibility for some issues related to death and due to this they get involved at the personal level, appropriate care and are affected as persons. Patient care during dying processes transcends the limits of the nurse' professional functions to become a human obligation.

Energy Saving Melting and Revert Reduction Technology (E-SMARRT): Development of Surface Engineered Coating Systems for Aluminum Pressure Die Casting Dies: Towards a 'Smart' Die Coating

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dr. John J. Moore; Dr. Jianliang Lin,

2012-07-31

The main objective of this research program was to design and develop an optimal coating system that extends die life by minimizing premature die failure. In high-pressure aluminum die-casting, the die, core pins and inserts must withstand severe processing conditions. Many of the dies and tools in the industry are being coated to improve wear-resistance and decrease down-time for maintenance. However, thermal fatigue in metal itself can still be a major problem, especially since it often leads to catastrophic failure (i.e. die breakage) as opposed to a wear-based failure (parts begin to go out of tolerance). Tooling costs remain themore » largest portion of production costs for many of these parts, so the ability prevent catastrophic failures would be transformative for the manufacturing industry.The technology offers energy savings through reduced energy use in the die casting process from several factors, including increased life of the tools and dies, reuse of the dies and die components, reduction/elimination of lubricants, and reduced machine down time, and reduction of Al solder sticking on the die. The use of the optimized die coating system will also reduce environmental wastes and scrap parts. Current (2012) annual energy saving estimates, based on initial dissemination to the casting industry in 2010 and market penetration of 80% by 2020, is 3.1 trillion BTU's/year. The average annual estimate of CO2 reduction per year through 2020 is 0.63 Million Metric Tons of Carbon Equivalent (MM TCE).« less

Being One with the Universe: Finding a Silver Lining in Dying.

PubMed

Caratao-Mojica, Rhea

2015-07-01

Woody Allen once quoted, "I don't mind dying so much, I just don't want to be there when it happens" (as cited in Ingram, 2002, p. 1). Oftentimes, death is not a happy subject, a reality that most of us fear, yet something we all must face. In this paper, three articles were reviewed that explored the living-dying (Phillips, 1992) process of the terminally ill and the material was conceptualized in light of Rogers (1994) science of unitary human beings. To further understand and explore the living-dying process, creative examples (movie screenplay, novel, song and others) were cited. During the living-dying process exploration, three common themes were expressed by the subjects (dying persons), namely: valuing own perspective of quality of life; choosing personal meanings with ways of moving beyond with the possibles (Lee & Pilkington, 1999), while focusing on life's meaning rather than life's details (Dobratz, 2002); and connecting to the world-as-unknown while self-separating to the world-as-known in actively seeking the union with death (Kubler-Ross, 1981; Callanan & Kelly, 1992; Dobratz, 2002). It is important for healthcare providers to recognize and acknowledge all three themes to be able to understand dying persons, to focus on their wholeness rather than their disease, and to help families discern symbolic messages conveyed by them. Moreover, knowing these themes also enables healthcare providers to help all parties to transition and be able to accept and embrace the most difficult process—the living-dying (Phillips, 1992) process. © The Author(s) 2015.

Telemedicine’s Potential to Support Good Dying in Nigeria: A Qualitative Study

PubMed Central

van Gurp, Jelle; Soyannwo, Olaitan; Odebunmi, Kehinde; Dania, Simpa; van Selm, Martine; van Leeuwen, Evert; Vissers, Kris; Hasselaar, Jeroen

2015-01-01

Objectives This qualitative study explores Nigerian health care professionals’ concepts of good dying/a good death and how telemedicine technologies and services would fit the current Nigerian palliative care practice. Materials and Methods Supported by the Centre for Palliative Care Nigeria (CPCN) and the University College Hospital (UCH) in Ibadan, Nigeria, the authors organized three focus groups with Nigerian health care professionals interested in palliative care, unstructured interviews with key role players for palliative care and representatives of telecom companies, and field visits to primary, secondary and tertiary healthcare clinics that provided palliative care. Data analysis consisted of open coding, constant comparison, diagramming of categorizations and relations, and extensive member checks. Results The focus group participants classified good dying into 2 domains: a feeling of completion of the individual life and dying within the community. Reported barriers to palliative care provision were socio-economic consequences of being seriously ill, taboos on dying and being ill, restricted access to adequate medical–technical care, equation of religion with medicine, and the faulty implementation of palliative care policy by government. The addition of telemedicine to Nigeria’s palliative care practice appears problematic, due to irregular bandwidth, poor network coverage, and unstable power supply obstructing interactivity and access to information. However, a tele-education ‘lite’ scenario seemed viable in Nigeria, wherein low-tech educational networks are central that build on non-synchronous online communication. Discussion Nigerian health care professionals’ concepts on good dying/a good death and barriers and opportunities for palliative care provision were, for the greater part, similar to prior findings from other studies in Africa. Information for and education of patient, family, and community are essential to further improve

Navigating "Assisted Dying".

PubMed

Schipper, Harvey

2016-02-01

Carter is a bellwether decision, an adjudication on a narrow point of law whose implications are vast across society, and whose impact may not be realized for years. Coupled with Quebec's Act Respecting End-of-life Care it has sharply changed the legal landscape with respect to actively ending a person's life. "Medically assisted dying" will be permitted under circumstances, and through processes, which have yet to be operationally defined. This decision carries with it moral assumptions, which mean that it will be difficult to reach a unifying consensus. For some, the decision and Act reflect a modern acknowledgement of individual autonomy. For others, allowing such acts is morally unspeakable. Having opened the Pandora's Box, the question becomes one of navigating a tolerable societal path. I believe it is possible to achieve a workable solution based on the core principle that "medically assisted dying" should be a very rarely employed last option, subject to transparent ongoing review, specifically as to why it was deemed necessary. My analysis is based on 1. The societal conditions in which have fostered demand for "assisted dying", 2. Actions in other jurisdictions, 3. Carter and Quebec Bill 52, 4. Political considerations, 5. Current medical practice. Leading to a series of recommendations regarding. 1. Legislation and regulation, 2. The role of professional regulatory agencies, 3. Medical professions education and practice, 4. Public education, 5. Health care delivery and palliative care. Given the burden of public opinion, and the legal steps already taken, a process for assisted-dying is required. However, those legal and regulatory steps should only be considered a necessary and defensive first step in a two stage process. The larger goal, the second step, is to drive the improvement of care, and thus minimize assisted-dying.

De-tabooing dying control - a grounded theory study

PubMed Central

2013-01-01

Background Dying is inescapable yet remains a neglected issue in modern health care. The research question in this study was “what is going on in the field of dying today?” What emerged was to eventually present a grounded theory of control of dying focusing specifically on how people react in relation to issues about euthanasia and physician-assisted suicide (PAS). Methods Classic grounded theory was used to analyze interviews with 55 laypersons and health care professionals in North America and Europe, surveys on attitudes to PAS among physicians and the Swedish general public, and scientific literature, North American discussion forum websites, and news sites. Results Open awareness of the nature and timing of a patient’s death became common in health care during the 1960s in the Western world. Open dying awareness contexts can be seen as the start of a weakening of a taboo towards controlled dying called de-tabooing. The growth of the hospice movement and palliative care, but also the legalization of euthanasia and PAS in the Benelux countries, and PAS in Montana, Oregon and Washington further represents de-tabooing dying control. An attitude positioning between the taboo of dying control and a growing taboo against questioning patient autonomy and self-determination called de-paternalizing is another aspect of de-tabooing. When confronted with a taboo, people first react emotionally based on “gut feelings” - emotional positioning. This is followed by reasoning and label wrestling using euphemisms and dysphemisms - reflective positioning. Rarely is de-tabooing unconditional but enabled by stipulated positioning as in soft laws (palliative care guidelines) and hard laws (euthanasia/PAS legislation). From a global perspective three shapes of dying control emerge. First, suboptimal palliative care in closed awareness contexts seen in Asian, Islamic and Latin cultures, called closed dying. Second, palliative care and sedation therapy, but not euthanasia

Agency behind bars: Advance care planning with aging and dying offenders.

PubMed

Sanders, Sara; Stensland, Meredith; Juraco, Kim

2018-01-01

Aging and terminally ill individuals in U.S. prisons are increasing, making critical the need for appropriate end-of-life (EOL) care and advance care planning (ACP). Applying Bandura's agentic perspective, the authors examined 20 aging/dying offenders' EOL preferences and ACP. Findings include 6 themes: decisions in the shadow of the past, what works best for me, feeling blessed, what is really going on, can anyone be trusted, and turning agency over to someone else. This study provides critical information that will assist professionals who work with dying offenders, as it presents a vivid illustration of their dying process.

Die singulation method and package formed thereby

DOEpatents

Anderson, Robert C [Tucson, AZ; Shul, Randy J [Albuquerque, NM; Clews, Peggy J [Tijeras, NM; Baker, Michael S [Albuquerque, NM; De Boer, Maarten P [Albuquerque, NM

2012-08-07

A method is disclosed for singulating die from a substrate having a sacrificial layer and one or more device layers, with a retainer being formed in the device layer(s) and anchored to the substrate. Deep Reactive Ion Etching (DRIE) etching of a trench through the substrate from the bottom side defines a shape for each die. A handle wafer is then attached to the bottom side of the substrate, and the sacrificial layer is etched to singulate the die and to form a frame from the retainer and the substrate. The frame and handle wafer, which retain the singulated die in place, can be attached together with a clamp or a clip and to form a package for the singulated die. One or more stops can be formed from the device layer(s) to limit a sliding motion of the singulated die.

Dying to remember, remembering to survive: mortality salience and survival processing.

PubMed

Burns, Daniel J; Hart, Joshua; Kramer, Melanie E; Burns, Amy D

2014-01-01

Processing items for their relevance to survival improves recall for those items relative to numerous other deep processing encoding techniques. Perhaps related, placing individuals in a mortality salient state has also been shown to enhance retention of items encoded after the morality salience manipulation (e.g., in a pleasantness rating task), a phenomenon we dubbed the "dying-to-remember" (DTR) effect. The experiments reported here further explored the effect and tested the possibility that the DTR effect is related to survival processing. Experiment 1 replicated the effect using different encoding tasks, demonstrating that the effect is not dependent on the pleasantness task. In Experiment 2 the DTR effect was associated with increases in item-specific processing, not relational processing, according to several indices. Experiment 3 replicated the main results of Experiment 2, and tested the effects of mortality salience and survival processing within the same experiment. The DTR effect and its associated difference in item-specific processing were completely eliminated when the encoding task required survival processing. These results are consistent with the interpretation that the mechanisms responsible for survival processing and DTR effects are overlapping.

Influences of die channel angles on microstructures and wear behaviors of AZ61 wrought magnesium alloy fabricated by extrusion-shear process

NASA Astrophysics Data System (ADS)

Hu, Hong-J.; Sun, Z.; Ou, Z.-W.

2016-12-01

Extrusion-shear (ES) process for magnesium alloy is a newly developed plastic deformation process, and ES process combines direct extrusion and two steps of ECAE (equal channel angular extrusion). To investigate the effects of the die channel angles on the microstructures and wear behaviors of AZ61 wrought magnesium alloy, the samples used in this study were fabricated by ES process with different die channel angles (120° and 135°). The microstructures of the samples were characterized by optical microscopy (OM), X-ray diffraction (XRD) and (SEM). The cumulative strains in the ES process were predicted by approaches of numerical simulation and theoretical calculation. To characterize the wear resistance of the samples, pin-on-disk tests under dry sliding conditions with various normal loads and reciprocating frequencies were conducted. To define the wear mechanisms of AZ61 magnesium alloy, the worn surfaces after wear tests were analyzed by SEM and energy-dispersive X-ray spectrometer (EDS). Based on the results obtained, die channel angles have significant influences on the grain refinements and wear behaviors of the samples. Decreasing channel angles of the ES die will not only refine the microstructures of magnesium alloys effectively and improve their harnesses, but also improve their wear resistance as decreasing channel angles results in higher friction coefficients and wear rates. With the increase in applied loads and frequencies, wear mechanisms change from mild wear (adhesion, abrasion and oxidation) to severe wear (delamination, plastic deformation and melting). In summary, the wear resistance of ES-processed AZ61 magnesium alloy could be improved by decreasing channel angles of ES dies.

Historical review of die drool phenomenon during plastics extrusion

NASA Astrophysics Data System (ADS)

Musil, Jan; Zatloukal, Martin

2013-04-01

Die drool phenomenon is defined as unwanted spontaneous accumulation of extruded polymer melt on open faces of extrusion die during extrusion process. Such accumulated material builds up on the die exit and frequently or continually sticks onto the extruded product and thus damages it. Since die drool appears, extrusion process must be shut down and die exit must be manually cleaned which is time and money consuming. Although die drool is complex phenomenon and its formation mechanism is not fully understood yet, variety of proposed explanations of its formation mechanism and also many ways to its elimination can be found in open literature. Our review presents in historical order breakthrough works in the field of die drool research, shows many ways to suppress it, introduces methods for its quantitative evaluation and composition analysis and summarizes theories of die drool formation mechanism which can be helpful for extrusion experts.

CAE Based Die Face Engineering Development to Contribute to the Revitalization of the Tool & Die Industry

NASA Astrophysics Data System (ADS)

Tang, Arthur; Lee, Wing C.; St. Pierre, Shawn; He, Jeanne; Liu, Kesu; Chen, Chin C.

2005-08-01

Over the past two decades, the Computer Aided Engineering (CAE) tools have emerged as one of the most important engineering tools in various industries, due to its flexibility and accuracy in prediction. Nowadays, CAE tools are widely used in the sheet metal forming industry to predict the forming feasibility of a wide variety of complex components, ranging from aerospace and automotive components to household products. As the demand of CAE based formability accelerates, the need for a robust and streamlined die face engineering tool becomes more crucial, especially in the early stage when the tooling layout is not available, but a product design decision must be made. Ability to generate blank, binder and addendum surfaces with an appropriate layout of Drawbead, Punch Opening Line, Trim Line are the primary features and functions of a CAE based die face engineering tool. Once the die face layout is ready, a formability study should be followed to verify the die face layout is adequate to produce a formable part. If successful, the established die face surface should be exported back to the CAD/CAM environment to speed up the tooling and manufacturing design process with confidence that this particular part is formable with this given die face. With a CAE tool as described above, the tool & die industry will be greatly impacted as the processes will enable the bypass of hardware try-out and shorten the overall vehicle production timing. The trend has shown that OEMs and first tiers will source to low cost producers in the world which will have a negative impact to the traditional tool & die makers in the developed countries. CAE based tool as described should be adopted, along with many other solutions, in order to maintain efficiency of producing high quality product and meeting time-to-market requirements. This paper will describe how a CAE based die face engineering (DFE) tool could be further developed to enable the traditional tool & die makers to meet the

L-connect routing of die surface pads to the die edge for stacking in a 3D array

DOEpatents

Petersen, Robert W.

2000-01-01

Integrated circuit chips and method of routing the interface pads from the face of the chip or die to one or more sidewall surfaces of the die. The interconnection is routed from the face of the die to one or more edges of the die, then routed over the edge of the die and onto the side surface. A new pad is then formed on the sidewall surface, which allows multiple die or chips to be stacked in a three-dimensional array, while enabling follow-on signal routing from the sidewall pads. The routing of the interconnects and formation of the sidewall pads can be carried out in an L-connect or L-shaped routing configuration, using a metalization process such as laser pantography.

Spanish Adaptation of the Frommelt Attitude Toward Care of the Dying Scale (FATCOD-S) in Nursing Undergraduates.

PubMed

Edo-Gual, Montserrat; Tomás-Sábado, Joaquín; Gómez-Benito, Juana; Monforte-Royo, Cristina; Aradilla-Herrero, Amor

2017-01-01

The Frommelt Attitude Toward Care of the Dying Scale (FATCOD) is designed to assess the attitudes of professionals and trainees toward caring for the dying patient and their family members. In this study the main aim is to adapt the FATCOD to a Spanish context (FATCOD-S). In addition, the relations between FATCOD-S, sociodemographic variables, emotional intelligence, and death attitudes have been analyzed. A sample of 669 Spanish nursing students from four Universities responded to a questionnaire. The exploratory factor analysis (EFA) concludes a structure composed of two significant factors. A confirmatory factor analysis (CFA) was carried out. The CFA supported a two-factor model. Students with past experience of death and those who had received training in palliative care scored significantly higher on both factors of the FATCOD-S ( p < 0.01). The FATCOD-S is an effective and valid tool for measuring the attitudes of Spanish nursing students toward caring for patients at the end of life.

Experimental and Numerical Studies on the Formability of Materials in Hot Stamping and Cold Die Quenching Processes

NASA Astrophysics Data System (ADS)

Li, N.; Mohamed, M. S.; Cai, J.; Lin, J.; Balint, D.; Dean, T. A.

2011-05-01

Formability of steel and aluminium alloys in hot stamping and cold die quenching processes is studied in this research. Viscoplastic-damage constitutive equations are developed and determined from experimental data for the prediction of viscoplastic flow and ductility of the materials. The determined unified constitutive equations are then implemented into the commercial Finite Element code Abaqus/Explicit via a user defined subroutine, VUMAT. An FE process simulation model and numerical procedures are established for the modeling of hot stamping processes for a spherical part with a central hole. Different failure modes (failure takes place either near the central hole or in the mid span of the part) are obtained. To validate the simulation results, a test programme is developed, a test die set has been designed and manufactured, and tests have been carried out for the materials with different forming rates. It has been found that very close agreements between experimental and numerical process simulation results are obtained for the ranges of temperatures and forming rates carried out.

[Significances of the life experience for the long-lived elderly person in the process of death/dying and mourning].

PubMed

Menezes, Tânia Maria de Oliva; Lopes, Regina Lúcia Mendonça

2014-08-01

This is a study using the Heideggerian theoretical-phenomenological approach, which sought to understand the significances of the life experience for the long-lived elderly person in the process of death/dying and mourning. It was conducted in 2009 with 16 long-lived senior citizens of both genders who were aged between 80 and 90, members of a community center for the elderly located in a suburban neighborhood of the city of Salvador in the state of Bahia, Brazil. The results showed that the long-lived elderly person experiences the mourning status process when relatives and friends become ill and die. Furthermore, they gave ambiguous reports with respect to the fear of death. With the attributed significances, it was possible to arrive at the unit of significance, namely the authenticity and lack of authenticity of the individual regarding imminent death. The conclusion reached is that long-lived elderly individuals faced with the process of death/dying and mourning is apparent or concealed in accordance with the moment they are experiencing and the opportunities that present themselves, in other words, it is greatly influenced by their past.

Numerical investigation of the effect of friction conditions to increase die life

NASA Astrophysics Data System (ADS)

Mutlu, M. O.; Guleryuz, C. G.; Parlar, Z.

2017-02-01

The standard die materials in aluminium extrusion offer good mechanical properties like high tempering resistance, high strength and ductility. On the other hand, they struggle with the problem of sliding wear. As a result, there is a growing interest in using surface treatment techniques to increase the wear resistance of extrusion dies. In this study, it is aimed to observe the effects of the different friction conditions on material flow and contact pressure in extrusion process. These friction conditions can be obtained with the application of a variety of surface treatment. In this way, it is expected to decrease the friction force on the die bearing area and to increase the homogeneity of the material flow which will result in the increase of the quality of the extrudate as well as the improvement of the process economically by extending die life. For this purpose, an extrusion process is simulated with a finite element software. A die made of 1.2344 hot work tool steel-commonly used die material for aluminium extrusion process- has been modelled and Al 1100 alloy used as billet material. Various friction factor values defined on the die surface under the same process parameters and effects of changing frictional conditions on the die and the extrusion process have been discussed.

Dying scenarios improve recall as much as survival scenarios.

PubMed

Burns, Daniel J; Hart, Joshua; Kramer, Melanie E

2014-01-01

Merely contemplating one's death improves retention for entirely unrelated material learned subsequently. This "dying to remember" effect seems conceptually related to the survival processing effect, whereby processing items for their relevance to being stranded in the grasslands leads to recall superior to that of other deep processing control conditions. The present experiments directly compared survival processing scenarios with "death processing" scenarios. Results showed that when the survival and dying scenarios are closely matched on key dimensions, and possible congruency effects are controlled, the dying and survival scenarios produced equivalently high recall levels. We conclude that the available evidence (cf. Bell, Roer, & Buchner, 2013; Klein, 2012), while not definitive, is consistent with the possibility of overlapping mechanisms.

Death and help expected from nurses when dying.

PubMed

Shih, Fu-Jin; Gau, Meei-Ling; Lin, Yaw-Sheng; Pong, Suang-Jing; Lin, Hung-Ru

2006-07-01

This project was undertaken to ascertain the perceptions of a group of Taiwan's fourth-year bachelor of science in nursing (BSN) students regarding death and help expected from nurses during the dying process. Within the Chinese culture, death is one of the most important life issues. However, in many Chinese societies it is difficult for people to reveal their deepest feelings to their significant others or loved ones. It was in this context that this project was developed because little is known about how Taiwan's nursing students perceive death and the dying process. Using an open-ended, self-report questionnaire, 110 senior BSN students recorded their thoughts on: (1) their fears before physical death; (2) afterlife destinations; and (3) the help they would expect from nurses when dying. The data were analyzed using a three-layer qualitative thematic analysis. The students' reported needs during the dying process were directed towards three main goals: (1) help in reaching the 'triple targets of individual life'; (2) help in facilitating in-depth support so that both the dying person and significant others can experience a blessed farewell; and (3) help in reaching a destination in the afterlife. The results support the belief of dying as a transition occurring when life weans itself from the mortal world and prepares for an afterlife.

Sheet metal stamping die design for warm forming

DOEpatents

Ghosh, Amit K.

2003-04-22

In metal stamping dies, by taking advantage of improved material flow by selectively warming the die, flat sections of the die can contribute to the flow of material throughout the workpiece. Local surface heating can be accomplished by placing a heating block in the die. Distribution of heating at the flat lower train central regions outside of the bend region allows a softer flow at a lower stress to enable material flow into the thinner, higher strain areas at the bend/s. The heating block is inserted into the die and is powered by a power supply.

Spatio-temporal development of vegetation die-off in a submerging coastal marsh

USGS Publications Warehouse

Schepers, Lennert; Kirwan, Matthew; Guntenspergen, Glenn R.; Temmerman, Stijn

2017-01-01

In several places around the world, coastal marsh vegetation is converting to open water through the formation of pools. This is concerning, as vegetation die-off is expected to reduce the marshes' capacity to adapt to sea level rise by vegetation-induced sediment accretion. Quantitative analyses of the spatial and temporal development of marsh vegetation die-off are scarce, although these are needed to understand the bio-geomorphic feedback effects of vegetation die-off on flow, erosion, and sedimentation. In this study, we quantified the spatial and temporal development of marsh vegetation die-off with aerial images from 1938 to 2010 in a submerging coastal marsh along the Blackwater River (Maryland, U.S.A). Our results indicate that die-off begins with conversion of marsh vegetation into bare open water pools that are relatively far (> 75 m) from tidal channels. As vegetation die-off continues, pools expand, and new pools emerge at shorter and shorter distances from channels. Consequently larger pools are found at larger distances from the channels. Our results suggest that the size of the pools and possibly the connection of pools with the tidal channel system have important bio-geomorphic implications and aggravate marsh deterioration. Moreover, we found that the temporal development of vegetation die-off in moderately degraded marshes is similar as the spatial die-off development along a present-day gradient, which indicates that the contemporary die-off gradient might be considered a chronosequence that offers a unique opportunity to study vegetation die-off processes.

Death and Dying: Issues for Educational Gerontologists.

ERIC Educational Resources Information Center

Wass, Hannelore, Myers, Jane E.

1984-01-01

Reviews research on death orientations, the dying process, and bereavement, with a major focus on the elderly. Suggests that relevant knowledge about death and dying are important for gerontological practitioners and proposes that death-related content be systematically integrated into academic curricula at the preservice and inservice levels.…

[Dying and death in societal transformation].

PubMed

Heller, Andreas; Wegleitner, Klaus

2017-01-01

Dying and death in modern societies are subject to profound social, professional and cultural-religious changes. Secularization and a stronger differentiation of societies have led to a change in the way humans handle the dying process. Normatively ritualized collective behaviour has been replaced by an individual, subjectivized approach. In late modern societies there are many different views of what "successful" or "good" dying means.In the article this change is described by the following seven theses: 1. We live longer and we die longer. 2. We no longer die suddenly and unexpectedly but slowly and foreseeably. 3. Even though our biological life on earth has become longer, our life has been shortened by the loss of eternity. 4. We no longer die on the stage of ritualized relationships with our family and neighbours but behind the curtains of organizations. 5. We live and die in a society of organizations and have to get organized for the final phase of our life. 6. Living and dying are no large, state-owned enterprises but small, private enterprises. 7. The hospice movement as well as palliative medicine have created public awareness, made dying a matter of discussion and offered a new set of options.In late modernism end-of-life care requires new approaches based on individual and shared responsibility as well as cooperation between professional institutions and community-based voluntary care.A change towards community care is visible. Thus "dying" is a topic in the discussion about the future of public health and societal solidarity.

Analysis and modeling of hot extrusion die for its service life enhancement

NASA Astrophysics Data System (ADS)

Akhtar, Syed Sohail

Aluminum extrusion finds extensive application in the construction, automobile and aerospace industries. High pressures, elevated temperatures, complex and intricate section geometries lead to repeated mechanical and thermal stresses in the die and affiliated tooling. Product rework and rejects can be traced back to various defects spread over the die life cycle: die design, die manufacture and heat treatment, process parameters, inprocess die maintenance/correction and, billet type and quality. Therefore, improved and efficient service life of die and related tooling used in the extrusion press is one the most important factors in maximizing productivity and minimizing cost for ensuring the economical efficiency of an aluminum extrusion plant. How often a die has to be scrapped and replaced with a new one directly contributes to the commercial viability of producing a certain profile. The focus of the current work is on three distinct yet inter-related studies pertaining to the improvement of aluminum extrusion die. Study-A (Die Failure Analysis) is an investigation of various modes and critical failure types based on industrial data (Chapter-2 ), examination of failed dies and finite element simulation for identification of critical process parameters and design features in die fatigue-life (Chapter-3). In Study-B (Die Surface Hardening Treatment), two-stage controlled gas nitriding process for H13 steel is evaluated, both experimentally and numerically, in terms of nitrided case morphology and properties (Chapter-4) followed by experimental and numerical investigation of the effects of repeated nitriding (Chapter-5), pre-nitriding surface preparation (Chapter-6) and die profile geometry (Chapter-7) on nitriding performance in regard to die service life. In Study-C (Effect of Billet Quality on Die Life), the effect of billet quality and related influencing extrusion parameters on the die service life is investigated based on industrial data and some regression

Packaged die heater

DOEpatents

Spielberger, Richard; Ohme, Bruce Walker; Jensen, Ronald J.

2011-06-21

A heater for heating packaged die for burn-in and heat testing is described. The heater may be a ceramic-type heater with a metal filament. The heater may be incorporated into the integrated circuit package as an additional ceramic layer of the package, or may be an external heater placed in contact with the package to heat the die. Many different types of integrated circuit packages may be accommodated. The method provides increased energy efficiency for heating the die while reducing temperature stresses on testing equipment. The method allows the use of multiple heaters to heat die to different temperatures. Faulty die may be heated to weaken die attach material to facilitate removal of the die. The heater filament or a separate temperature thermistor located in the package may be used to accurately measure die temperature.

Student Nurses' Perception of Death and Dying

ERIC Educational Resources Information Center

Niederriter, Joan E.

2009-01-01

Student nurses are involved in caring for patients who are actively dying or who have been told they have a terminal illness and are faced with the process of dying. Students encounter these patients in hospitals, nursing homes, at home or in hospice care settings. According to Robinson (2004), "nurses are the healthcare providers that are most…

Nursing students' experiences caring for dying patients.

PubMed

Beck, C T

1997-11-01

Since the 1960s nurse educators have been searching for the most effective approach to prepare nursing students for care of the dying. Studies investigating the effectiveness of death education programs for nursing students have reported inconsistent findings. A phenomenological study was conducted to explore the meaning of 26 undergraduate nursing students' experiences in caring for dying patients. The nursing students' written descriptions of their experiences were analyzed using Colaizzi's (1978) phenomenological method. Six themes emerged from this analysis. While caring for dying patients, nursing students experienced a gamut of emotions such as fear, sadness, frustration, and anxiety. Contemplation of the patient's life and death occurred as the students cared for their patients. In addition to providing physical, emotional, and spiritual support for dying patients, an integral part of nursing students' care involved supporting the patients' families. Helplessness was experienced by the students regarding their role as patient advocates. While caring for dying patients, nursing students' learning fluorished. Educational strategies for preparing nursing students to care for the dying are addressed based on the findings of this qualitative study.

Regional ontogeny of New England salt marsh die-off.

PubMed

Coverdale, Tyler C; Bertness, Mark D; Altieri, Andrew H

2013-10-01

Coastal areas are among the world's most productive and highly affected ecosystems. Centuries of human activity on coastlines have led to overexploitation of marine predators, which in turn has led to cascading ecosystem-level effects. Human effects and approaches to mediating them, however, differ regionally due to gradients in biotic and abiotic factors. Salt marsh die-off on Cape Cod, Massachusetts (U.S.A.), triggered by a recreational-fishing-induced trophic cascade that has released herbivorous crabs from predator control, has been ongoing since 1976. Similar salt marsh die-offs have been reported in Long Island Sound and Narragansett Bay (U.S.A.), but the driving mechanism of these die-offs has not been examined. We used field experiments to assess trophic interactions and historical reconstructions of 24 New England marshes to test the hypotheses that recreational fishing and predator depletion are a regional trigger of salt marsh die-off in New England and that die-offs in Long Island Sound and Narragansett Bay are more recent than those on Cape Cod. Predator depletion was the general trigger of marsh die-off and explained differences in herbivorous crab abundance and the severity of die-off across regions. Die-offs in Long Island Sound and Narragansett Bay are following a trajectory similar to die-off on Cape Cod, but are approximately 20 years behind those on Cape Cod. As a result, die-off currently affects 31.2% (SE 2.2) of low-marsh areas in Long Island Sound and Narragansett Bay, less than half the severity of die-off on Cape Cod. Our results contribute to the growing evidence that recreational fishing is an increasing threat to coastal ecosystems and that studying the effects of human activity at regional scales can provide insight into local effects and aid in early detection and potential remediation. © 2013 Society for Conservation Biology.

Analysis of Porosity Defects in Aluminum as Part Handle Motor Vehicle Lever Processed by High-pressure Die Casting

NASA Astrophysics Data System (ADS)

Anggraini, L.; Sugeng

2018-05-01

This research discusses the testing and analysis of cracking Aluminum (Al) material. Al as a handle lever was used for a braking device on a motor vehicle. Cracking of handle lever due to the part content of porosity from hydrogen gas. The existence of the H2 can be caused by the casting process and dies design that is less perfect, especially at the gate or brisket and overflow. This research is to optimize the process of making Al part handle lever, and the construction dies by following the standard. The results of these improvements were reevaluated through the chemical and mechanical testing properties stages, such as density test and tensile test on the workpiece as part handle lever. The loads on the tensile test are 25 kg and 35 kg, and the tensile test result has met the standard set by the motor vehicle company. The optimization result has the porosity defect can be reduced by 99 %. Therefore the best part handle lever can be produced.

SPHERICAL DIE

DOEpatents

Livingston, J.P.

1959-01-27

A die is presented for pressing powdered materials into a hemispherical shape of uniforin density and wall thickness comprising a fcmale and male die element held in a stationary spaced relation with the space being equivalent to the wall thickness and defining the hemispherical shape, a pressing ring linearly moveable along the male die element, an inlet to fill the space with powdered materials, a guiding system for moving the pressing ring along the male die element so as to press the powdered material and a heating system for heating the male element so that the powdered material is heated while being pressed.

Laser micromilling of convex microfluidic channels onto glassy carbon for glass molding dies

NASA Astrophysics Data System (ADS)

Tseng, Shih-Feng; Chen, Ming-Fei; Hsiao, Wen-Tse; Huang, Chien-Yao; Yang, Chung-Heng; Chen, Yu-Sheng

2014-06-01

This study reports the fabrication of convex microfluidic channels on glassy carbon using an ultraviolet laser processing system to produce glass molding dies. The laser processing parameters, including various laser fluences and scanning speeds of galvanometers, were adjusted to mill a convex microchannel on a glassy carbon substrate to identify the effects of material removal. The machined glassy carbon substrate was then applied as a glass molding die to fabricate a glass-based microfluidic biochip. The surface morphology, milled width and depth, and surface roughness of the microchannel die after laser micromilling were examined using a three-dimensional confocal laser scanning microscope. This study also investigates the transcription rate of microchannels after the glass molding process. To produce a 180 μm high microchannel on the GC substrate, the optimal number of milled cycles, laser fluence, and scanning speed were 25, 4.9 J/cm2, and 200 mm/s, respectively. The width, height, and surface roughness of milled convex microchannels were 119.6±0.217 μm, 180.26±0.01 μm, and 0.672±0.08 μm, respectively. These measured values were close to the predicted values and suitable for a glass molding die. After the glass molding process, a typical glass-based microchannel chip was formed at a molding temperature of 660 °C and the molding force of 0.45 kN. The transcription rates of the microchannel width and depth were 100% and 99.6%, respectively. Thus, the proposed approach is suitable for performing in chemical, biochemical, or medical reactions.

Die Starter: A New System to Manage Early Feasibility in Sheet Metal Forming

NASA Astrophysics Data System (ADS)

Narainen, Rodrigue; Porzner, Harald

2016-08-01

Die Starter, a new system developed by ESI Group, allows the user to drastically reduce the number of iterations during the early tool process feasibility. This innovative system automatically designs the first quick die face, generating binder and addendum surfaces (NURBS surfaces) by taking account the full die process. Die Starter also improves the initial die face based on feasibility criteria (avoiding splits, wrinkles) by automatically generating the geometrical modifications of the binder and addendum and the bead restraining forces with minimal material usage. This paper presents a description of the new system and the methodology of Die Starter. Some industrial examples are presented from the part geometry to final die face including automatic developed flanges, part on binder and inner binder.

Die Soldering in Aluminium Die Casting

DOE Office of Scientific and Technical Information (OSTI.GOV)

Han, Q.; Kenik, E.A.; Viswanathan, S.

2000-03-15

Two types of tests, dipping tests and dip-coating tests were carried out on small steel cylinders using pure aluminum and 380 alloy to investigate the mechanism of die soldering during aluminum die casting. Optical and scanning electron microscopy were used to study the morphology and composition of the phases formed during soldering. A soldering mechanism is postulated based on experimental observations. A soldering critical temperature is postulated at which iron begins to react with aluminum to form an aluminum-rich liquid phase and solid intermetallic compounds. When the temperature at the die surface is higher than this critical temperature, the aluminum-richmore » phase is liquid and joins the die with the casting during the subsequent solidification. The paper discusses the mechanism of soldering for the case of pure aluminum and 380 alloy casting in a steel mold, the factors that promote soldering, and the strength of the bond formed when soldering occurs. conditions, an aluminum-rich soldering layer may also form over the intermetallic layer. Although a significant amount of research has been conducted on the nature of these intermetallics, little is known about the conditions under which soldering occurs.« less

The Transformation Process in Nurses Caring for Dying Patients.

PubMed

Huang, Ching-Chi; Chen, Jih-Yuan; Chiang, Hsien-Hsien

2016-06-01

Despite the recent increase in attention to end-of-life hospice care, little empirical evidence regarding the process of emotional or mental transformation in caregivers is available. This study explores the transformative process that occurs in nurses because of the spiritual suffering and conflict associated with after caring for dying patients. A phenomenological approach was used to investigate eight nurses (27-40 years old) working in the hospice ward of a medical center in Taipei. Data were collected through open-ended questions using semistructured interviews and were analyzed reflectively. A three-stage transformation in the emotional processes of participants was observed. In the first stage, the participants experienced acute emotional suffering because of facing the death of their patients, potentially exacerbated by their own memories of losing family members. In the second stage, the participants adopted coping strategies to improve self-care. These strategies included attempting to soothe patients, helping patients face or deal with unfulfilled business, and participating in funeral or memorial services. In the third stage, the participants learned to provide better care through emancipatory reflection and a reassertion of responsibilities toward the self, patients, and patient families. After the third stage, the initial emotional impact morphed into a medium for self-strengthening, and participants became more adept at detecting patient needs and at providing care to complete the transformational process fully. Emotional suffering was the primary factor that induced participants to transform their personal and professional selves. Adequate emotional self-management, dialogue with other nurses, and personal reflection are crucial actions that nurses may use to cultivate personal growth, implement ethical practice, interact with other nurses, and engage in personal reflection. Strategies such as caring for patients, implementing reflective nursing

Development and Demonstration of Adanced Tooling Alloys for Molds and Dies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kevin M. McHugh; Enrique J. Lavernia

2006-01-01

This report summarizes research results in the project Development and Demonstration of Advanced Tooling Alloys for Molds and Dies. Molds, dies and related tooling are used to manufacture most of the plastic and metal products we use every day. Conventional fabrication of molds and dies involves a multiplicity of machining, benching and heat treatment unit operations. This approach is very expensive and time consuming. Rapid Solidifcation Process (RSP) Tooling is a spray-forming technology tailored for producing molds and dies. The appraoch combines rapid solidifcation processing and net-shape materials processing in a single step. An atomized spray of a tool-forming alloy,more » typically a tool steel, is deposited onto an easy-to-form tool pattern to replicate the pattern's shape and surface features. By so doing, the approach eliminates many machining operations in conventional mold making, significantly reducing cost, lead time and energy. Moreover, rapid solidification creates unique microstructural features by suppressing carbide precipitation and growth, and creating metastable phases. This can result in unique material properties following heat treatment. Spray-formed and aged tool steel dies have exhibited extended life compared to conventional dies in many forming operations such as forging, extrusion and die casting. RSP Tooling technolocy was commercialized with the formation of RSP Tooling, LLC in Solon, Oh.« less

Challenges Facing a Deaf Family Member Concerning a Loved One’s Dying

PubMed Central

Kehl, Karen A.; Gartner, Constance M.

2010-01-01

Individuals who are Deaf face challenges both similar and unique from those faced by hearing individuals when a family member is dying. This study was guided by the question “What are the challenges faced by a Deaf family member when a loved one is dying?” Methods - This qualitative study is guided by critical theory and an interpretive perspective. Robert, a college-educated older adult who has been Deaf from birth was interviewed in American Sign Language using a death history format. Results – There are challenges for Deaf family members that affect communication with both the dying person and health care professionals. Patient-family communication issues included physical challenges and financial challenges. Lack of cultural competence concerning the Deaf community created challenges communicating with professionals. Decision-making was also a challenge. Conclusions These findings provide a framework for future research concerning the needs of Deaf individuals facing the end of life and provide guidance for clinicians. PMID:19910395

When a Baby Dies.

ERIC Educational Resources Information Center

Church, Martha Jo; And Others

Written especially for grieving mothers whose babies have died, this booklet offers an overview of stages and experiences through which bereaved parents commonly pass. Specifically, the text is intended to give comfort to bereaved parents, offer insight into the grieving process, and provide thoughts on leave-taking ceremonies. The first section…

Looking Beyond Where Children Die: Determinants and Effects of Planning a Child’s Location of Death

PubMed Central

Dussel, Veronica; Kreicbergs, Ulrika; Hilden, Joanne M.; Watterson, Jan; Moore, Caron; Turner, Brian G.; Weeks, Jane C.; Wolfe, Joanne

2009-01-01

While dying at home may be the choice of many, where people die may be less important than argued. We examined factors associated with parental planning of a child’s location of death (LOD) and its effects on patterns of care and parent’s experience. In a cross-sectional study of 140 parents who lost a child to cancer at one of two tertiary level U.S. pediatric hospitals, 88 (63%) planned the child’s LOD and 97% accomplished their plan. After adjusting for disease and family characteristics, families whose primary oncologist clearly explained treatment options during the child’s end of life (EOL) and who had home care involved were more likely to plan LOD. Planning LOD was associated with more home deaths (72% versus 8% among those who did not plan, P<0.001) and fewer hospital admissions (54% versus 98%, P<0.001). Parents who planned were more likely to feel very prepared for the child’s EOL (33% versus 12%, P=0.007) and very comfortable with LOD (84% versus 40%, P<0.001), and less likely to have preferred a different LOD (2% versus 46%, P<0.001). Among the 73 non-home deaths, planning was associated with more deaths occurring in the ward than in the intensive care unit or other hospital (92% versus 33%, P<0.001), and fewer children being intubated (21% versus 48%, P=0.029). Comprehensive physician communication and home care involvement increase the likelihood of planning a child’s LOD. Opportunity to plan LOD is associated with outcomes consistent with high quality palliative care, even among non-home deaths, and thus may represent a more relevant outcome than actual LOD. PMID:18538973

HIGH PRESSURE DIES

DOEpatents

Wilson, W.B.

1960-05-31

A press was invented for subjecting specimens of bismuth, urania, yttria, or thoria to high pressures and temperatures. The press comprises die parts enclosing a space in which is placed an electric heater thermally insulated from the die parts so as not to damage them by heat. The die parts comprise two opposed inner frustoconical parts and an outer part having a double frustoconical recess receiving the inner parts. The die space decreases in size as the inner die parts move toward one another against the outer part and the inner parts, though very hard, do not fracture because of the mode of support provided by the outer part.

Influence of die geometry and material selection on the behavior of protective die covers in closed-die forging

NASA Astrophysics Data System (ADS)

Yu, Yingyan; Rosenstock, Dirk; Wolfgarten, Martin; Hirt, Gerhard

2016-10-01

Due to the fact that tooling costs make up to 30% of total costs of the final forged part, the tool life is always one main research topic in closed-die forging [1]. To improve the wear resistance of forging dies, many methods like nitriding and deposition of ceramic layers have been used. However, all these methods will lose its effect after a certain time, then tool repair or exchange is needed, which requires additional time and costs. A new method, which applies an inexpensive and changeable sheet metal on the forging die to protect it from abrasive wear, was firstly proposed in [2]. According to the first investigation, the die cover is effective for decreasing thermal and mechanical loads, but there are still several challenges to overcome in this concept, like wrinkling and thinning of the die cover. Therefore, an experimental study using different geometries and die cover materials is presented within this work. The results indicate the existence of feasible application cases of this concept, since conditions are found under which a die cover made of 22MnB5 still keeps its original shape even after 7 forging cycles.

Die Sonne.

NASA Astrophysics Data System (ADS)

der Time-Life Bücher, Redaktion

Contents: 1. Das Antlitz der Sonne. Ein kosmisches Kraftwerk. 2. Erforschung des Innern. Die Beobachtung des Zentralgestirns. 3. Der unstete Nachbar. Geschenke des Sonnenlichts. 4. Ein endloser Partikelstrom. Die Kraft eines solaren Sturms.

No Negative Impact of Palliative Sedation on Relatives’ Experience of the Dying Phase and Their Wellbeing after the Patient’s Death: An Observational Study

PubMed Central

van der Lee, M. L.; Vergouwe, Y.

2016-01-01

Background Palliative sedation is the widely-used intervention of administering sedating agents to induce a state of unconsciousness to take away a dying patient’s perception of otherwise irrelievable symptoms. However, it remains questionable whether this ethically complex intervention is beneficial for patients and whether the associated lack of communication in the last phase of life has a negative impact on relatives’ wellbeing. Methods An observational questionnaire study was conducted among relatives of a consecutive sample of patients who died a non-sudden death in the Erasmus MC Cancer Institute or in the hospice ‘Laurens Cadenza’ (both in Rotterdam) between 2010 and 2013. Results Relatives filled in questionnaires regarding 151 patients who had been sedated and 90 patients who had not been sedated. The median time since all patients had passed away was 21 (IQR 14–32) months. No significant differences were found in relatives´ assessments of the quality of end-of-life care, patients´ quality of life in the last week before death and their quality of dying, between patients who did and did not receive sedation, or in relatives’ satisfaction with their own life, their general health and their mental wellbeing after the patient’s death. Conclusions The use of sedation in these patients appears to have no negative effect on bereaved relatives’ evaluation of the patient’s dying phase, or on their own wellbeing after the patient’s death. PMID:26871717

[End-of-life-care and euthanasia: medical assistance in dying or help to die].

PubMed

Müller-Busch, H Christof

2008-01-01

The debate on euthanasia that has been started all over Europe, but especially in Germany has been particularly complicated by unclear and inconsistent definitions. Medical decisions in end-of-life care gain increasing importance not only for the time of death but also for the kind and quality of the dying process. Though legal regulations can help to diminish doubts about the permissibility of various measures in end-of-life care, teaching and knowledge of ethical principles, communication skills, respect, transparency and knowledge of palliative care options seem to be the most important factors in accompanying the dying professionally and with dignity and even in achieving a consented compromise when aid in hastening death is asked for.

Robert Merton Dies at 92

ERIC Educational Resources Information Center

Snell, Joel C.

2006-01-01

This article features Robert Merton, who died recently at age 92. Merton came into this world as a Jewish baby named Meyer Schkolnick. He lived in South Philly where his parents wrenched a living as blue-collar workers. Merton chose an Anglicized name to move into the Yankee dominated America of the 20's and 30's. At Harvard, he studied under…

Nano Precipitation and Hardening of Die-Quenched 6061 Aluminum Alloy.

PubMed

Utsunomiya, Hiroshi; Tada, Koki; Matsumoto, Ryo; Watanabe, Katsumi; Matsuda, Kenji

2018-03-01

Die quenching is applied to an age-hardenable aluminium alloys to obtain super-saturated solid solution. The application is advantageous because it can reduce number of manufacturing processes, and may increase strength by strain aging. If die quenching is realized in forging as well as sheet forming, it may widen industrial applicability further. In this study, Al-Mg-Si alloy AA6061 8 mm-thick billets were reduced 50% in height without cracks by die-quench forging. Supersaturated solid solution was successfully obtained. The die-quenched specimen shows higher hardness with nano precipitates at shorter aging time than the conventional water-quenched specimen.

The thermal fatigue resistance of H-13 Die Steel for aluminum die casting dies

NASA Technical Reports Server (NTRS)

1982-01-01

The effects of welding, five selected surface coatings, and stress relieving on the thermal fatigue resistance of H-13 Die Steel for aluminum die casting dies were studied using eleven thermal fatigue specimens. Stress relieving was conducted after each 5,000 cycle interval at 1050 F for three hours. Four thermal fatigue specimens were welded with H-13 or maraging steel welding rods at ambient and elevated temperatures and subsequently, subjected to different post-weld heat treatments. Crack patterns were examined at 5,000, 10,000, and 15,000 cycles. The thermal fatigue resistance is expressed by two crack parameters which are the average maximum crack and the average cracked area. The results indicate that a significant improvement in thermal fatigue resistance over the control was obtained from the stress-relieving treatment. Small improvements were obtained from the H-13 welded specimens and from a salt bath nitrogen and carbon-surface treatment. The other surface treatments and welded specimens either did not affect or had a detrimental influence on the thermal fatigue properties of the H-13 die steel.

Care at the Very End-of-Life: Dying Cancer Patients and Their Chosen Family’s Needs

PubMed Central

Clark, Katherine

2017-01-01

The majority of cancer deaths in countries such as Australia are predictable and most likely to occur in hospital. Despite this, hospitals remain challenged by providing the best care for this fragile cohort, often believing that care with palliative intent at the very end-of-life is not the best approach to care. Given the importance that dying patients place on excellent symptom control, failing to provide good end-of-life care is likely to be contrary to the wishes of the imminently dying patient and their family. This becomes even more significant when the impact of care on the bereavement outcomes of families is considered. Given the rising numbers of predicable hospital deaths, an urgent need to address this exists, requiring health professionals to be cognisant of specific care domains already identified as significant for both patients and those closest to them in knowledge, care and affection. This non-systematic review’s aims are to summarise the symptoms most feared by people imminently facing death which is defined as the terminal phase of life, where death is imminent and likely to occur within hours to days, or very occasionally, weeks. Further, this paper will explore the incidence and management of problems that may affect the dying person which are most feared by their family. The final section of this work includes a brief discussion of the most significant issues that require attention. PMID:28125017

Identifying Regulators of the Immune Response to Dying Cells | Center for Cancer Research

Cancer.gov

Cytotoxic T cells are responsible for carrying out antigen-mediated immune responses against virally-infected and malignant cells. In both cases, cytotoxic T cells are stimulated by interacting with antigen presenting cells, such as dendritic cells (DCs). Infected cells produce virus-specific antigens and pathogen associated molecular patterns, which are recognized by DCs and lead to robust T cell activation. Dead or dying uninfected cells, on the other hand, release damage associated molecular patterns, but their release does not always appear to be sufficient to induce cytotoxic T cell activity. Tim Greten, M.D., of CCR’s Medical Oncology Branch, and a group of international collaborators set out to understand how immune responses against dying cancer cells are regulated. These processes are likely to be important for improving the efficacy of cancer treatment vaccines, which induce an immune reaction against a patient’s cancer cells.

Assisted Dying & Disability.

PubMed

Riddle, Christopher A

2017-07-01

This article explores at least two dominant critiques of assisted dying from a disability rights perspective. In spite of these critiques, I conclude that assisted dying ought to be permissible. I arrive at the conclusion that if we respect and value people with disabilities, we ought to permit assisted dying. I do so in the following manner. First, I examine recent changes in legislation that have occurred since the Royal Society of Canada Expert Panel on End-of-Life Decision-Making report, published in this journal. I suggest that these changes are likely to only strengthen opposition to assisted dying from disability rights activists and people with disabilities. Second, I focus on respect for people with disabilities and in particular, respect for their autonomy and decision-making abilities. Third, I explore the opposition to assisted dying that focuses on risk and the vulnerability of people with disabilities. Here I suggest that this risk ought not to be of special concern. Ultimately, I conclude that upholding respect for the disabled requires the legalization of assisted dying, rather than the denial of access in a misguided effort to protect people with disabilities. © 2017 John Wiley & Sons Ltd.

Micromechanical die attachment surcharge

DOEpatents

Filter, William F.; Hohimer, John P.

2002-01-01

An attachment structure is disclosed for attaching a die to a supporting substrate without the use of adhesives or solder. The attachment structure, which can be formed by micromachining, functions purely mechanically in utilizing a plurality of shaped pillars (e.g. round, square or polygonal and solid, hollow or slotted) that are formed on one of the die or supporting substrate and which can be urged into contact with various types of mating structures including other pillars, a deformable layer or a plurality of receptacles that are formed on the other of the die or supporting substrate, thereby forming a friction bond that holds the die to the supporting substrate. The attachment structure can further include an alignment structure for precise positioning of the die and supporting substrate to facilitate mounting the die to the supporting substrate. The attachment structure has applications for mounting semiconductor die containing a microelectromechanical (MEM) device, a microsensor or an integrated circuit (IC), and can be used to form a multichip module. The attachment structure is particularly useful for mounting die containing released MEM devices since these devices are fragile and can otherwise be damaged or degraded by adhesive or solder mounting.

Teaching about Dying and Death in a Multidisciplinary Student Group.

ERIC Educational Resources Information Center

Barton, David; And Others

1979-01-01

Discusses dimensions which emerged in a multidisciplinary class of medical, nursing, social work, and theology students about dying and death. Group process was the most important aspect. Students evaluated their roles and transactions in caring for the dying. The recognition of solidarity of purpose, shared feeling, and mutual support emerged.…

A process chain for integrating piezoelectric transducers into aluminum die castings to generate smart lightweight structures

NASA Astrophysics Data System (ADS)

Stein, Stefan; Wedler, Jonathan; Rhein, Sebastian; Schmidt, Michael; Körner, Carolin; Michaelis, Alexander; Gebhardt, Sylvia

The application of piezoelectric transducers to structural body parts of machines or vehicles enables the combination of passive mechanical components with sensor and actuator functions in one single structure. According to Herold et al. [1] and Staeves [2] this approach indicates significant potential regarding smart lightweight construction. To obtain the highest yield, the piezoelectric transducers need to be integrated into the flux of forces (load path) of load bearing structures. Application in a downstream process reduces yield and process efficiency during manufacturing and operation, due to the necessity of a subsequent process step of sensor/actuator application. The die casting process offers the possibility for integration of piezoelectric transducers into metal structures. Aluminum castings are particularly favorable due to their high quality and feasibility for high unit production at low cost (Brunhuber [3], Nogowizin [4]). Such molded aluminum parts with integrated piezoelectric transducers enable functions like active vibration damping, structural health monitoring or energy harvesting resulting in significant possibilities of weight reduction, which is an increasingly important driving force of automotive and aerospace industry (Klein [5], Siebenpfeiffer [6]) due to increasingly stringent environmental protection laws. In the scope of those developments, this paper focuses on the entire process chain enabling the generation of lightweight metal structures with sensor and actuator function, starting from the manufacturing of piezoelectric modules over electrical and mechanical bonding to the integration of such modules into aluminum (Al) matrices by die casting. To achieve this challenging goal, piezoceramic sensors/actuator modules, so-called LTCC/PZT modules (LPM) were developed, since ceramic based piezoelectric modules are more likely to withstand the thermal stress of about 700 °C introduced by the casting process (Flössel et al., [7]). The

THE EFFECT OF LASER SHOCK PEENING ON THE LIFE AND FAILURE MODE OF A COLD PILGER DIE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lavender, Curt A.; Hong, Sung-tae; Smith, Mark T.

2008-08-11

The laser shock peening process was used to increase fatigue life of pilger dies made of A2 tool steel by imparting compressive residual stresses to fatigue prone areas of the dies. The result of X-Ray diffraction analysis indicated that deep, high- magnitude compressive residual stresses were generated by the laser shock peening process, and the peened dies exhibited a significant increase of in-service life. Fractography of the failed dies indicates that the fracture mechanism was altered by the peening process.

Development of materials for the rapid manufacture of die cast tooling

NASA Astrophysics Data System (ADS)

Hardro, Peter Jason

The focus of this research is to develop a material composition that can be processed by rapid prototyping (RP) in order to produce tooling for the die casting process. Where these rapidly produced tools will be superior to traditional tooling production methods by offering one or more of the following advantages: reduced tooling cost, shortened tooling creation time, reduced man-hours for tool creation, increased tool life, and shortened die casting cycle time. By utilizing RP's additive build process and vast material selection, there was a prospect that die cast tooling may be produced quicker and with superior material properties. To this end, the material properties that influence die life and cycle time were determined, and a list of materials that fulfill these "optimal" properties were highlighted. Physical testing was conducted in order to grade the processability of each of the material systems and to optimize the manufacturing process for the downselected material system. Sample specimens were produced and microscopy techniques were utilized to determine a number of physical properties of the material system. Additionally, a benchmark geometry was selected and die casting dies were produced from traditional tool materials (H13 steel) and techniques (machining) and from the newly developed materials and RP techniques (selective laser sintering (SLS) and laser engineered net shaping (LENS)). Once the tools were created, a die cast alloy was selected and a preset number of parts were shot into each tool. During tool creation, the manufacturing time and cost was closely monitored and an economic model was developed to compare traditional tooling to RP tooling. This model allows one to determine, in the early design stages, when it is advantageous to implement RP tooling and when traditional tooling would be best. The results of the physical testing and economic analysis has shown that RP tooling is able to achieve a number of the research objectives, namely

How dying cells alert the immune system to danger

PubMed Central

Kono, Hajime; Rock, Kenneth L.

2009-01-01

When a cell dies in vivo the event does not go unnoticed. The host has evolved mechanisms to detect the death of cells and rapidly investigate the nature of their demise. If cell death is a result of natural causes, that is, it is part of normal physiological processes, then there is little threat to the organism. In this situation, little else is done other than removing the corpse. However, if cells have died as the consequence of some violence or disease, then both defence and repair mechanisms are mobilized. The importance of this process to host defence and disease pathogenesis has only been appreciated relatively recently. This article will review our current knowledge of these processes. PMID:18340345

Importance of the advance directive and the beginning of the dying process from the point of view of German doctors and judges dealing with guardianship matters: results of an empirical survey.

PubMed

van Oorschot, B; Simon, A

2006-11-01

To analyse and compare the surveys on German doctors and judges on end of life decision making regarding their attitudes on the advance directive and on the dying process. The respondents were to indicate their agreement or disagreement to eight statements on the advance directive and to specify their personal view on the beginning of the dying process. 727 doctors (anaesthetists or intensive-care physicians, internal specialists and general practitioners) in three federal states and 469 judges dealing with guardianship matters all over Germany. Comparisons of means, analyses of variance, pivot tables (chi(2) test) and factor analyses (varimax with Kaiser normalisation). Three attitude groups on advance directive were disclosed by the analysis: the decision model, which emphasises the binding character of a situational advance directive; the deliberation model, which puts more emphasis on the communicative aspect; and the delegation model, which regards the advance directive as a legal instrument. The answers regarding the beginning of the dying process were broadly distributed, but no marked difference was observed between the responding professions. The dying process was assumed by most participants to begin with a life expectancy of only a few days. A high degree of valuation for advance directive was seen in both German doctors and judges; most agreed to the binding character of the situational directive. Regarding the different individual concepts of the dying process, a cross-professional discourse on the contents of this term seems to be overdue.

Assisted dying in liberalised jurisdictions and the role of psychiatry: a clinician's view.

PubMed

Macleod, Sandy

2012-10-01

Assisted dying is a contentious and topical issue. Mental disorder is a relevant influence on requests of hastened death. The psychiatry of dying is not a prominent component in the assessment of euthanasia and physician-assisted suicide (PAS) in jurisdictions with liberalised assisted dying laws. The literature on the assessment processes, with particular reference to mental status, involved in euthanasia requests is considered. An experienced palliative medicine specialist and psychiatrist selectively reviewed the recent literature published about the mental health issues involved in euthanasia and PAS. Assessments of competency, sustained wish to die prematurely, depressive disorder, demoralisation and 'unbearable suffering' in the terminally ill are clinically uncertain and difficult tasks. There is a growing psychiatric and psychological literature on the mental status of the terminally ill. As yet psychiatry does not have the expertise to 'select' those whose wish for hastened death is rational, humane and 'healthy'. Rarely in those societies with liberalised assisted dying laws are psychiatrists involved in the decision-making for individuals requesting early death. This role is fulfilled by non-specialists. There remain significant concerns about the accuracy of psychiatric assessment in the terminally ill. Mental processes are more relevant influences on a hastened wish to die than are the physical symptoms of terminal malignant disease. Psychiatric review of persons requesting euthanasia is relevant. It is not obligatory or emphasised in those legislations allowing assisted dying. Psychiatry needs to play a greater role in the assessment processes of euthanasia and PAS.

Study the effect of elevated dies temperature on aluminium and steel round deep drawing

NASA Astrophysics Data System (ADS)

Lean, Yeong Wei; Azuddin, M.

2016-02-01

Round deep drawing operation can only be realized by expensive multi-step production processes. To reduce the cost of processes while expecting an acceptable result, round deep drawing can be done at elevated temperature. There are 3 common problems which are fracture, wrinkling and earing of deep drawing a round cup. The main objective is to investigate the effect of dies temperature on aluminium and steel round deep drawing; with a sub-objective of eliminate fracture and reducing wrinkling effect. Experimental method is conducted with 3 different techniques on heating the die. The techniques are heating both upper and lower dies, heating only the upper dies, and heating only the lower dies. 4 different temperatures has been chosen throughout the experiment. The experimental result then will be compared with finite element analysis software. There is a positive result from steel material on heating both upper and lower dies, where the simulation result shows comparable as experimental result. Heating both upper and lower dies will be the best among 3 types of heating techniques.

Herausforderungen durch die deutsche Wiedervereinigung

NASA Astrophysics Data System (ADS)

Stäglin, Reiner

Die Wiedervereinigung stellte auch die Statistik vor große Aufgaben. Die als Organ der staatlichen Planung staatsnah orientierte Statistik der DDR musste auf das zur Neutralität und wissenschaftlichen Unabhängigkeit verpflichtete System der Bundesrepublik umgestellt werden. Ebenso verlangten die Universitäten eine Neuorientierung. Die Deutsche Statistische Gesellschaft hat sich vor allem dreier Aufgaben mit großem Engagement, aber auch mit Bedachtsamkeit angenommen: Aufnahme und Integration der Statistiker aus den neuen Bundesländern in die Gesellschaft, Begleitung der Neuausrichtung des Faches Statistik an deren Hochschulen und Sicherung sowie Nutzung von Datenbeständen der ehemaligen DDR.

Small-Scale Die-Offs in Woodrats Support Long-Term Maintenance of Plague in the U.S. Southwest.

PubMed

Kosoy, Michael; Reynolds, Pamela; Bai, Ying; Sheff, Kelly; Enscore, Russell E; Montenieri, John; Ettestad, Paul; Gage, Kenneth

2017-09-01

Our longitudinal study of plague dynamics was conducted in north-central New Mexico to identify which species in the community were infected with plague, to determine the spatial and temporal patterns of the dynamics of plague epizootics, and to describe the dynamics of Yersinia pestis infection within individual hosts. A total of 3156 fleas collected from 535 small mammals of 8 species were tested for Y. pestis DNA. Nine fleas collected from six southern plains woodrats (Neotoma micropus) and from one rock squirrel (Otospermophilus variegatus) were positive for the pla gene of Y. pestis. None of 127 fleas collected from 17 woodrat nests was positive. Hemagglutinating antibodies to the Y. pestis-specific F1 antigen were detected in 11 rodents of 6 species. All parts of the investigated area were subjected to local disappearance of woodrats. Despite the active die-offs, some woodrats always were present within the relatively limited endemic territory and apparently were never exposed to plague. Our observations suggest that small-scale die-offs in woodrats can support maintenance of plague in the active U.S. Southwestern focus.

Displaced capillary dies

DOEpatents

Kalejs, Juris P.; Chalmers, Bruce; Surek, Thomas

1982-01-01

An asymmetrical shaped capillary die made exclusively of graphite is used to grow silicon ribbon which is capable of being made into solar cells that are more efficient than cells produced from ribbon made using a symmetrically shaped die.

Displaced capillary dies

DOEpatents

Kalejs, Juris P.; Chalmers, Bruce; Surek, Thomas

1984-01-01

An asymmetrical shaped capillary die made exclusively of graphite is used to grow silicon ribbon which is capable of being made into solar cells that are more efficient than cells produced from ribbon made using a symmetrically shaped die.

Mediation: a response to aid-in-dying and the Supreme Court decision.

PubMed

Saulo, M; Wagener, R J; Rothschild, I S

1998-01-01

The recent U.S. Supreme Court decision concerning aid-in-dying has drawn attention to the complexity of end-of-life care. The authors summarize the recent Supreme Court's decision and the problems surrounding this complex issue. A case study is provided to demonstrate how mediation facilitates collaborative problem solving. Finally, the authors demonstrate how nurse leaders can apply this three-stage process and its attendant principles to facilitate ethical decision making in end-of-life care.

Wissenschaft, die unsere Kultur verändert. Tiefenschichten des Streits um die Evolutionstheorie

NASA Astrophysics Data System (ADS)

Patzelt, Werner J.

Die Evolutionstheorie ist eine der erfolgreichsten wissenschaftlichen Theorien. Sie erlaubt es, unsere Herkunft zu verstehen und riskante Merkmale gerade der menschlichen Spezies zu begreifen. Zugleich ist die Evolutionstheorie eine der umstrittensten Theorien. Das liegt nicht an ihrer empirischen Tragfähigkeit, sondern an ihrem Gegenstand. Sie handelt nämlich nicht nur - wie Hunderte andere wissenschaftliche Theorien - von der "Welt da draußen“, sondern vor allem auch von uns selbst und von unserem Platz in dieser Welt. Den einen gilt sie obendrein als Überwinderin religiösen Aberglaubens, den anderen als neuer Zugang zu Gott und seinem Wirken in der Welt. Ferner sehen die einen in der Evolution eine unbezweifelbare Tatsache gleich der Schwerkraft oder dem Holocaust, die anderen aber eine - noch oder dauerhaft - unbewiesene Hypothese oder gar eine falsche Schöpfungslehre. Und während die meisten Streitfragen solcher Art nach wechselseitig akzeptierten Regeln ‚normaler Wissenschaft‘ geklärt werden, wird bei der Frage nach dem Woher unserer Spezies und Kultur die intellektuelle Zuständigkeit von Wissenschaft mitunter überhaupt bezweifelt. Anscheinend geht es schon um recht tiefe Schichten unserer Kultur und nicht nur der wissenschaftlichen, wenn - wie seit 150 Jahren - um die Evolutionstheorie gestritten wird. Wie sehen diese Schichten aus?

The Ambiguous Dying Syndrome

ERIC Educational Resources Information Center

Bern-Klug, Mercedes

2004-01-01

More than one-half of the 2.4 million deaths that will occur in the United States in 2004 will be immediately preceded by a time in which the likelihood of dying can best be described as "ambiguous." Many people die without ever being considered "dying" or "at the end of life." These people may miss out on the…

Fatigue of die cast zinc alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schrems, K.K.; Dogan, O.N.; Goodwin, F.E.

2006-04-01

The rotating bending fatigue limit of die cast zinc alloy 2, alloy 3, alloy 5, AcuZinc 5, and ZA-8 were determined as a part of an on-going program by ILZRO into the mechanical properties of die cast zinc. The stress-life (S-N) curves of alloys 3, 5, AcuZinc 5, and ZA-8 were determined previously. This presentation reports the results of the S-N curve for Alloy 2 and the calculated fatigue limits for all five alloys. During the previous stress-life testing, the samples were stopped at 10 million cycles and the fatigue limit for alloy 3, alloy 5, and AcuZinc 5 appearedmore » to be higher and the fatigue limit for ZA-8 appeared to be lower than the values reported in the literature. This was further investigated in alloy 5 and ZA-8 by testing continuous cast bulk alloy 5 and ZA-8.« less

Doing one's utmost: nurses' descriptions of caring for dying patients in an intensive care environment.

PubMed

Fridh, Isabell; Forsberg, Anna; Bergbom, Ingegerd

2009-10-01

The aim of this study was to explore nurses' experiences and perceptions of caring for dying patients in an intensive care unit (ICU) with focus on unaccompanied patients, the proximity of family members and environmental aspects. Interviews were conducted with nine experienced ICU nurses. A qualitative descriptive approach was employed. The analysis was performed by means of conventional content analysis [Hsieh HF, Shannon SE. Three approaches to qualitative content analysis. Qual Health Res 2005;15:1277-88] following the steps described by e.g. Elo and Kyngas [Elo S, Kyngas H. The qualitative content analysis process. J Adv Nurs 2008;62:107-15]. The analysis resulted in a main category; Doing one's utmost, described by four generic categories and 15 sub-categories, comprising a common vision of the patients' last hours and dying process. This description was dominated by the nurses' endeavour to provide dignified end-of-life care (EOLC) and, when relatives were present, to give them an enduring memory of their loved one's death as a calm and dignified event despite his/her previous suffering and death in a high-technological environment. This study contributes new knowledge about what ICU nurses focus on when providing EOLC to unaccompanied patients but also to those whose relatives were present. Nurses' EOLC was mainly described as their relationship and interaction with the dying patient's relatives, while patients who died alone were considered tragic but left a lesser impression in the nurses' memory.

Spray forming process for producing molds, dies and related tooling

DOEpatents

McHugh, Kevin M.; Key, James F.

1998-01-01

A method for spray forming manufacturing of near-net-shape molds, dies and related toolings, wherein liquid material such as molten metal, metallic alloys, or polymers are atomized into fine droplets by a high temperature, high velocity gas and deposited onto a pattern. Quenching of the atomized droplets provides a heat sink, thereby allowing undercooled and partially solidified droplets to be formed in-flight. Composites can be formed by combining the atomized droplets with solid particles such as whiskers or fibers.

A Covering Type Extrusion Die with Twin Cavities for Semi-Hollow Al-Profiles

NASA Astrophysics Data System (ADS)

Deng, Rurong; Huang, Xuemei

2018-03-01

A new structure named covering type with twin cavities in a die for the semi-hollow aluminum profiles was present. The determination of structure parameters was introduced in detail. Mainly including the selection of the machine, the arrangement of portholes, the structure design of chamber and the selection of bearing. The method of checking the die strength was introduced. According to the extrusion results, the structure of the traditional solid die, the porthole die with single cavity and the covering type structure with twin cavities were compared. The characteristics of the latter structure were simple and easy to process. The practical application shows that the new die structure can enhance the die life, improve the production efficiency and reduce the cost. The high precision and the surface brightness of the profiles were obtained. The structure is worth promoting. The aim is to provide reliable data and reference for the further research and development of this technology on the extrusion die with multi-cavities in a die.

Attitude of Palestinian Nursing Students Toward Caring for Dying Patients: A Call for Change in Health Education Policy.

PubMed

Abu-El-Noor, Nasser Ibrahim; Abu-El-Noor, Mysoon Khalikl

2016-06-01

Death is a natural process that occurs each day. Some nursing students may encounter the experience of taking care of a dying patient while others do not. Therefore, their attitude toward death and caring for dying patients may vary. The purpose of this study was to assess Palestinian student nurses' attitudes toward death and caring for dying patients and their families. In a cross-sectional, descriptive study, all fourth-year students at the College of Nursing, Islamic University of Gaza, Palestine, were invited to participate in this study. A total of 141 students completed the Frommelt Attitude Toward Care of the Dying Scale Form B (FATCOD-B). Results revealed that the mean score on the FATCOD-B was (96.96 ± 8.30). Overall, nursing students in the sample demonstrated a relatively low attitude toward caring for dying patients and their families. No statistically significant differences of students' attitudes toward caring for dying patients were found between male and female students nor between students who attended death cases and those who did not. The results suggest that theoretical nursing education should place more emphasis on palliative care to improve the quality of care at the end of life. © The Author(s) 2015.

Dying with dignity: the good patient versus the good death.

PubMed

Proulx, Kathryn; Jacelon, Cynthia

2004-01-01

Death is a unique experience for each human being, yet there is tremendous societal pressure on a dying person to be a "goodpatient " while trying to experience the "good death. " These pressures shape patient, caregiver, and family choices in end-of-life situations. The purpose of this literature review was twofold: first, to develop an understanding of "dying with dignity" to enhance the end-of-life care received by dying patients, and second, to contribute to a concept analysis of dignity to improve the clarity and consistency of future research related to dignity in aging individuals. Articles pertaining to dying with dignity from the disciplines of nursing, medicine, ethics, psychology, and sociology were reviewed using a matrix method. A dichotomy surrounding dying with dignity emerged from this review. The definition of dignity in dying identifies not only an intrinsic, unconditional quality of human worth, but also the external qualities of physical comfort, autonomy, meaningfulness, usefulness, preparedness, and interpersonal connection. For many elderly individuals, death is a process, rather than a moment in time, resting on a need for balance between the technology of science and the transcendence of spirituality.

Neighbour-die effect on the measurement of wafer-level flip-chip LED dies in production lines

NASA Astrophysics Data System (ADS)

Chen, Tengfei; Wan, Zirui; Li, Bin

2017-11-01

The light from the side surfaces of the test flip-chip light-emitting diode (FCLED) dies is reflected, refracted or absorbed by neighbour dies during the measurement of wafer-level FCLED dies in production lines. A notable measurement deviation is caused by the neighbour-die effect, which is not considered in current industry practice. In this paper, Monte Carlo ray-tracing simulations are used to study the measurement deviations caused by the neighbour-die effect and extension ratios of the film. The simulation results show that the maximal deviation of radiant flux impinging the photodiode can reach 5.5%, if the die is tested without any neighbour dies, or is surrounded by a set of neighbour dies at an extension ratio of 1.1. Moreover, the dependence between the measurement results and neighbour cases for different extension ratios is also investigated. Then, a modified calibration method is proposed and studied. The proposed technique can be used to improve the calibration and measurement accuracy of the test equipment used for measurement of wafer-level FCLED dies in production lines.

A study on die wear model of warm and hot forgings

NASA Astrophysics Data System (ADS)

Kang, J. H.; Park, I. W.; Jae, J. S.; Kang, S. S.

1998-05-01

Factors influencing service lives of tools in warm and hot forging processes are wear, mechanical fatigue, plastic deformation and thermal fatigue, etc. Wear is the predominant factor for tool failure among these. To predict tool life by wear, Archard's model where hardness is considered as constant or function of temperature is generally applied. Usually hardness of die is a function of not only temperature but operating time of die. To consider softening of die by repeated operation it is necessary to express hardness of die by a function of temperature and time. In this study wear coefficients were measured for various temperatures and heat treatment for H13 tool steel. Also by experiment of reheating of die, die softening curves were obtained. From experimental results, relationships between tempering parameters and hardness were established to investigate effects of hardness decrease by the effect of temperatures and time. Finally modified Archard's wear model in which hardness is considered to be a function of main tempering curve was proposed. And finite element analyses were conducted by adopting suggested wear model. By comparisons of simulations and real profiles of worn die, proposed wear model was verified.

[Legal issues of physician-assisted euthanasia. Part II--Help in the dying process, direct and indirect active euthanasia].

PubMed

Laux, Johannes; Röbel, Andreas; Parzeller, Markus

2013-01-01

In Germany, physician-assisted euthanasia involves numerous risks for the attending physician under criminal and professional law. In the absence of clear legal provisions, four different categories of euthanasia have been developed in legal practice and the relevant literature: help in the dying process, direct active euthanasia, indirect active euthanasia and passive euthanasia. The so-called "help during the dying process" by administering medically indicated analgesic drugs without a life-shortening effect is exempt from punishment if it corresponds to the will of the patient. If the physician omits to give such analgesic drugs although the patient demands them, this is deemed a punishable act of bodily injury. The same applies if the physician administers analgesics against the will of the patient. Medically indicated pain treatment which has a potential or certain life-shortening effect (indirect active euthanasia) is permitted under certain conditions: if there are no alternative and equally suitable treatment options without the risk of shortening the patient's life, if the patient has given his consent to the treatment and if the physician does not act with the intention to kill. The deliberate killing of a dying or terminally ill patient for the purpose of ending his suffering (direct active euthanasia) is prohibited. This includes both deliberately killing a patient against or without his will (by so-called "angels of death") and the killing of a patient who expressly and earnestly demands such an act from his physician (killing on request/on demand). Physician-assisted suicide is generally not liable to punishment in Germany. Nevertheless, the action may be subject to punishment if the physician omits to rescue the life of an unconscious suicide victim. "Palliative sedation" is regarded as a special case. It may become necessary if certain symptoms in the terminal stage of a fatal disease unbearable for the patient cannot be controlled by any other

Spray forming process for producing molds, dies and related tooling

DOEpatents

McHugh, K.M.; Key, J.F.

1998-02-17

A method is disclosed for spray forming manufacturing of near-net-shape molds, dies and related toolings, wherein liquid material such as molten metal, metallic alloys, or polymers are atomized into fine droplets by a high temperature, high velocity gas and deposited onto a pattern. Quenching of the atomized droplets provides a heat sink, thereby allowing undercooled and partially solidified droplets to be formed in-flight. Composites can be formed by combining the atomized droplets with solid particles such as whiskers or fibers. 17 figs.

The Lived Experiences of Nurses Caring For Dying Pediatric Patients.

PubMed

Curcio, Danna L

2017-01-01

Nurses and healthcare professionals may have difficulty adjusting to and comprehending their experiences when a patient’s life ends. This has the potential to interfere with patient care. Reflection on past events and actions enables critical discovery of strategies to benefit both nurses and patients. This qualitative phenomenological study explores the lived experiences of nurses caring for dying pediatric patients. The philosophical underpinning of Merleau-Ponty (2008), in combination with the research method of van Manen (1990), was used for this study. The Roy Adaptation Model (RAM) (Roy, 2009; Roy & Andrews, 1991) was the nursing model that guided the study to help understand that nurses are an adaptive system, using censoring as a compensatory adaptive process to help function for a purposeful cause. Nine female nurse participants with one to four years of experience were interviewed. The context of the experiences told by nurses caring for dying pediatric patents uncovered seven essential themes of empathy, feelings of ambivalence, inevitability, inspiration, relationship, self-preservation, and sorrow, and these themes demonstrated a connection formed between the nurse and the patient.

Extrusion die and method

DOEpatents

Lipp, G. Daniel

1994-04-26

A method and die apparatus for manufacturing a honeycomb body of rhombic cell cross-section by extrusion through an extrusion die of triangular cell discharge slot configuration, the die incorporating feedholes at selected slot intersections only, such that slot segments communicating directly with the feedholes discharge web material and slot segments not so connected do not discharge web material, whereby a rhombic cell cross-section in the extruded body is provided.

High moisture corn stover pelleting in a flat die pellet mill fitted with a 6 mm die: physical properties and specific energy consumption

DOE PAGES

Tumuluru, Jaya Shankar

2015-06-15

The quality and specific energy consumption (SEC) of the biomass pellets produced depend upon pelleting process conditions. The present study includes understanding the effect of feedstock moisture in the range of 28–38% (wet basis [w.b.]) and preheating in the range of 30–110°C at two die speeds of 40 and 60 Hz on the physical properties and SEC. A flat die pellet mill fitted with a 6 mm die was used in the present study. The physical properties of pellets such as moisture content, unit, bulk and tapped density, durability, and expansion ratio and SEC of the pelleting process are measured.more » The results indicate that the pellets produced have durability values in the range of 87–98%, and unit bulk and tapped density in the range of 670–1100, 375–575, and 420–620 kg/m³. Increasing the feedstock moisture content from 33% to 38% (w.b) decreased the unit, bulk and tapped density by about 30–40%. Increasing feedstock moisture content increased the expansion ratio and decreased the density values. A higher feedstock moisture content of 38% (w.b.) and higher preheating temperature of 110°C resulted in lower density and a higher expansion ratio, which can be attributed to flash off of moisture as the material extrudes out of the die. The SEC was in the range of 75–275 kWh/ton. Higher feedstock moisture content of 38% (w.b.) and a lower die speed of 40 Hz increased the SEC, whereas lower to medium preheating temperature (30–70°C), medium feedstock moisture content of 33% (w.b.), and a higher die speed of 60 Hz minimized the SEC to <100 kWh/ton.« less

Rheometry of polymer melts using processing machines

NASA Astrophysics Data System (ADS)

Friesenbichler, Walter; Neunhäuserer, Andreas; Duretek, Ivica

2016-08-01

The technology of slit-die rheometry came into practice in the early 1960s. This technique enables engineers to measure the pressure drop very precisely along the slit die. Furthermore, slit-die rheometry widens up the measurable shear rate range and it is possible to characterize rheological properties of complicated materials such as wall slipping PVCs and high-filled compounds like long fiber reinforced thermoplastics and PIM-Feedstocks. With the use of slit-die systems in polymer processing machines e.g., Rauwendaal extrusion rheometer, by-pass extrusion rheometer, injection molding machine rheometers, new possibilities regarding rheological characterization of thermoplastics and elastomers at processing conditions near to practice opened up. Special slit-die systems allow the examination of the pressure-dependent viscosity and the characterization of cross-linking elastomers because of melt preparation and reachable shear rates comparable to typical processing conditions. As a result of the viscous dissipation in shear and elongational flows, when performing rheological measurements for high-viscous elastomers, temperature-correction of the apparent values has to be made. This technique was refined over the last years at Montanuniversitaet. Nowadays it is possible to characterize all sorts of rheological complicated polymeric materials under process- relevant conditions with viscosity values fully temperature corrected.

Small-Scale Die-Offs in Woodrats Support Long-Term Maintenance of Plague in the U.S. Southwest

PubMed Central

Reynolds, Pamela; Bai, Ying; Sheff, Kelly; Enscore, Russell E.; Montenieri, John; Ettestad, Paul; Gage, Kenneth

2017-01-01

Abstract Our longitudinal study of plague dynamics was conducted in north-central New Mexico to identify which species in the community were infected with plague, to determine the spatial and temporal patterns of the dynamics of plague epizootics, and to describe the dynamics of Yersinia pestis infection within individual hosts. A total of 3156 fleas collected from 535 small mammals of 8 species were tested for Y. pestis DNA. Nine fleas collected from six southern plains woodrats (Neotoma micropus) and from one rock squirrel (Otospermophilus variegatus) were positive for the pla gene of Y. pestis. None of 127 fleas collected from 17 woodrat nests was positive. Hemagglutinating antibodies to the Y. pestis-specific F1 antigen were detected in 11 rodents of 6 species. All parts of the investigated area were subjected to local disappearance of woodrats. Despite the active die-offs, some woodrats always were present within the relatively limited endemic territory and apparently were never exposed to plague. Our observations suggest that small-scale die-offs in woodrats can support maintenance of plague in the active U.S. Southwestern focus. PMID:28792853

Self-Determination, the Right to Die, and Culture: A Literature Review

ERIC Educational Resources Information Center

McCormick, Andrew J.

2011-01-01

Self-determination is a primary ethical principle underlying social work practice in health care settings. Since the 1970s, a right-to-die movement that shares the social work commitment to self-determination has grown and influences end-of-life care decisions. However, the role of culture is notably absent in discussions of the right to die. A…

Psychotherapy with Older Dying Persons.

ERIC Educational Resources Information Center

Dye, Carol J.

Psychotherapy with older dying patients can lead to problems of countertransference for the clinician. Working with dying patients requires flexibility to adapt basic therapeutics to the institutional setting. Goals of psychotherapy must be reconceptualized for dying clients. The problems of countertransference arise because clinicians themselves…

3D FEM Geometry and Material Flow Optimization of Porthole-Die Extrusion

NASA Astrophysics Data System (ADS)

Ceretti, Elisabetta; Mazzoni, Luca; Giardini, Claudio

2007-05-01

The aim of this work is to design and to improve the geometry of a porthole-die for the production of aluminum components by means of 3D FEM simulations. In fact, the use of finite element models will allow to investigate the effects of the die geometry (webs, extrusion cavity) on the material flow and on the stresses acting on the die so to reduce the die wear and to improve the tool life. The software used to perform the simulations was a commercial FEM code, Deform 3D. The technological data introduced in the FE model have been furnished by METRA S.p.A. Company, partner in this research. The results obtained have been considered valid and helpful by the Company for building a new optimized extrusion porthole-die.

Nursing the dying: implications of Kübler-Ross' staging theory.

PubMed

Germain, C P

1980-01-01

Society's failure to value the work of nurses, the professionals most frequently involved in the care of the dying, is attributed to a cultural definition of nursing as a second-class occupation and the public's need to deny the realities of the suffering and indignities often associated with the process of dying. Efforts within the field of nursing to improve the care of the dying, by shifting emphasis from a narrow physical focus to a more holistic patient and family focus, preceded the past decade's contributions of Elisabeth Kübler-Ross. Although her staging theory has been cited as having limitations in development and in interpretation, Kübler-Ross' influence towards increasing awareness of the needs of the dying and others experiencing major losses has been substantial as evidenced by many references to staging theory in nursing literature, by a marked increase in attention to holistic care of the dying in the basic and continuing education programs of nursing, and by specialty role development in nursing care of the dying. This decade has also witnessed the major growth of professionalism in nursing, including strides towards professional autonomy. Conflict with the traditional pattern of medical dominance and bureacratic constraints in institutions is inevitable, especially when the medical goal of cure is not attainable. Change to an interdisciplinary model of care is viewed as essential for optimal care of the dying and their families.

Limitation of Shrinkage Porosity in Aluminum Rotor Die Casting

NASA Astrophysics Data System (ADS)

Kim, Young-Chan; Choi, Se-Weon; Kim, Cheol-Woo; Cho, Jae-Ik; Lee, Sung-Ho; Kang, Chang-Seog

Aluminum rotor prone to have many casting defects especially large amount of air and shrinkage porosity, which caused eccentricity, loss and noise during motor operation. Many attempts have been made to develop methods of shrinkage porosity control, but still there are some problems to solve. In this research, the process of vacuum squeeze die casting is proposed for limitation of defects. The 6 pin point gated dies which were in capable of local squeeze at the end ring were used. Influences of filling patterns on HPDC were evaluated and the important process control parameters were high injection speed, squeeze length, venting and process conditions. By using local squeeze and vacuum during filling and solidification, air and shrinkage porosity were significantly reduced and the feeding efficiency at the upper end ring was improved 10%. As a result of controlling the defects, the dynamometer test showed improved motor efficiency by more than 4%.

Manufacture of gradient micro-structures of magnesium alloys using two stage extrusion dies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hwang, Yeong-Maw; Huang, Tze-Hui; Alexandrov, Sergei

2013-12-16

This paper aims to manufacture magnesium alloy metals with gradient micro-structures using hot extrusion process. The extrusion die was designed to have a straight channel part combined with a conical part. Materials pushed through this specially-designed die generate a non-uniform velocity distribution at cross sections inside the die and result in different strain and strain rate distributions. Accordingly, a gradient microstructure product can be obtained. Using the finite element analysis, the forming temperature, effective strain, and effective strain rate distributions at the die exit were firstly discussed for various inclination angles in the conical die. Then, hot extrusion experiments withmore » a two stage die were conducted to obtain magnesium alloy products with gradient micro-structures. The effects of the inclination angle on the grain size distribution at cross sections of the products were also discussed. Using a die of an inclination angle of 15°, gradient micro-structures of the grain size decreasing gradually from 17 μm at the center to 4 μm at the edge of product were achieved.« less

Medizintechnik in der Tumororthopädie

NASA Astrophysics Data System (ADS)

Burgkart, Rainer; Gollwitzer, Hans; Holzapfel, Boris; Rudert, Maximilian; Rechl, Hans; Gradinger, Reiner

Die Behandlung der Knochentumoren unterlag in den letzten 20 Jahren einem raschen und stetigen Wandel, was zum einen auf die verbesserten Therapieerfolge durch den Einsatz von neoadjuvanten Therapieformen zurückzuführen ist, und andererseits von medizintechnischen Entwicklungen bezüglich moderner Schnittbilddiagnostik, neuer 3D Operationsplanungsverfahren wie das Rapid Prototyping und adaptiv modularer Tumorendoprothesensystemen u. a. begleitet wurde. Gerade die technischen Entwicklungen haben dazu geführt, daß im Bereich der Extremitäten und der Wirbelsäule radikalere Eingriffe durchgeführt werden können, was die lokale Tumorkontrolle wesentlich verbessert hat. In zunehmenden Maße werden deshalb nicht nur Kurzzeiterfolge sondern auch mittel- und langfristige Fortschritte bei der Behandlung der malignen Knochentumoren einschließlich der Metastasenbehandlung erreicht. Grundlage der Therapie ist dabei immer primär die Sicherung der Diagnose mittels Biopsie und die bildgebende sowie histologische Stadieneinteilung des malignen Tumors. Nach der Tumorresektion kann die Rekonstruktion biologisch oder mit Endoprothesensystemen erfolgen. Gerade die weiterentwickelten modularen Systeme führen zu guten funktionellen Ergebnissen mit langen Standzeiten und einer reduzierten Komplikationsrate. Individuell angefertigte Implantate sind vor allem im Bereich der Rekonstruktion komplexer Beckentumoren von großer klinischer Bedeutung.

Fundamental studies on a novel die concept for round-point shear-clinching

NASA Astrophysics Data System (ADS)

Hörhold, Réjane; Müller, Martin; Merklein, Marion; Meschut, Gerson

2016-10-01

A newly-developed round-point shear-clinching technology could increase the use of different materials like well formable aluminium and hardly formable ultra-high-strength steels (UHSS). This innovative technology joins in a single-stage process without any pilot-hole, surface pre-treatment or auxiliary joining part. The combination of an inner and outer punch realises an indirect cutting operation of the die-sided material, whereas the punch-sided material remains unharmed. The current die-sided tool set acts as a cutting die and enables a radial extrusion of the punch-sided material after being drawn though the created hole in the UHSS. The die has a fixed die depth. After ejecting the joined components, the slug has to be removed from the top of the spring-loaded anvil. The novel die concept investigated in this paper offers the possibility to push the slug continuously through the die in the joining direction. The removed slugs remain inside the die, so manual removal is unnecessary. The one-parted tool is supposed to be more robust than the multi-parted one that is currently used. This paper represents the task to evaluate the geometry of a useful shear-clinching die concept. To reduce the experimental effort, FEM should assist the development of the most promising approach. To quantify the success, conventional shear-clinching with opening die acts as a reference. The results show the high potential and the raison d'être of shear-clinching technologies as a mechanical joining technology for future multimaterial applications especially for UHSS.

Three-Dimensional Computed Tomography as a Method for Finding Die Attach Voids in Diodes

NASA Technical Reports Server (NTRS)

Brahm, E. N.; Rolin, T. D.

2010-01-01

NASA analyzes electrical, electronic, and electromechanical (EEE) parts used in space vehicles to understand failure modes of these components. The diode is an EEE part critical to NASA missions that can fail due to excessive voiding in the die attach. Metallography, one established method for studying the die attach, is a time-intensive, destructive, and equivocal process whereby mechanical grinding of the diodes is performed to reveal voiding in the die attach. Problems such as die attach pull-out tend to complicate results and can lead to erroneous conclusions. The objective of this study is to determine if three-dimensional computed tomography (3DCT), a nondestructive technique, is a viable alternative to metallography for detecting die attach voiding. The die attach voiding in two- dimensional planes created from 3DCT scans was compared to several physical cross sections of the same diode to determine if the 3DCT scan accurately recreates die attach volumetric variability

Vacuum die attach for integrated circuits

DOEpatents

Schmitt, Edward H.; Tuckerman, David B.

1991-01-01

A thin film eutectic bond for attaching an integrated circuit die to a circuit substrate is formed by coating at least one bonding surface on the die and substrate with an alloying metal, assembling the die and substrate under compression loading, and heating the assembly to an alloying temperature in a vacuum. A very thin bond, 10 microns or less, which is substantially void free, is produced. These bonds have high reliability, good heat and electrical conduction, and high temperature tolerance. The bonds are formed in a vacuum chamber, using a positioning and loading fixture to compression load the die, and an IR lamp or other heat source. For bonding a silicon die to a silicon substrate, a gold silicon alloy bond is used. Multiple dies can be bonded simultaneously. No scrubbing is required.

Investigating the Evolution of Progressive Die Wear on Uncoated Dp1180 Steel in Production Environment

NASA Astrophysics Data System (ADS)

Wu, W.; Zhou, D. J.; Adamski, D. J.; Young, D.; Wang, Y. W.

2017-09-01

A study of die wear was performed using an uncoated dual phase, 1,180 MPa ultimate tensile strength steel (DP1180) in a progressive die. The objectives of the current study are to evaluate the die durability of various tooling materials and coatings for forming operations on uncoated DP1180 steel and update OEM’s die standards based on the experimental results in the real production environment. In total, 100,800 hits were performed in manufacturing production conditions, where 33 die inserts with the combination of 10 die materials and 9 coatings were investigated. The die inserts were evaluated for surface wear using scanning electron microscopy and characterized in terms of die material and/or coating defects, failure mode, failure initiation and propagation. Surface roughness of the formed parts was characterized using a WYKO NT110 machine. The analytical analysis of the die inserts and formed parts, combined with the failure mode and service life, provide a basis for die material and coating selection for forming AHSS components. The conclusions of this study will guide the selection of die material and coatings for high-volume production of AHSS components.

Apparatus for restraining and transporting dies

DOEpatents

Allison, James W.; LaBarre, Timothy L.

1994-01-01

Apparatus for restraining and transporting dies in punch press operations is provided. A floatation platen for supporting a die on the platen's upper surface has a plurality of recessed gas exhaust ports on the platen's lower surface. A source of pressurized gas delivers gas to a platen manifold, for delivery to orifices located in the gas exhaust ports. The flow of gas is controlled by a first valve adjacent the gas source and a second valve adjacent the manifold, with the second valve being used to control the gas flow during movement of the die. In this fashion, a die may be moved on a cushion of air from one workstation to a selected second workstation. A moveable hydraulically operated restraining fixture is also provided, for clamping the die in position during the compacting phase, and for releasing the die after completion of the compacting phase by releasing the hydraulic pressure on the restraining fixture. When pressure in the hydraulic cylinders on the restraining fixture is reversed, the restraining fixture will retract so that there is no contact between the die and the restraining fixture, thereby allowing the die to be removed from a first workstation and moved to a second selected workstation.

Vacuum die attach for integrated circuits

DOEpatents

Schmitt, E.H.; Tuckerman, D.B.

1991-09-10

A thin film eutectic bond for attaching an integrated circuit die to a circuit substrate is formed by coating at least one bonding surface on the die and substrate with an alloying metal, assembling the die and substrate under compression loading, and heating the assembly to an alloying temperature in a vacuum. A very thin bond, 10 microns or less, which is substantially void free, is produced. These bonds have high reliability, good heat and electrical conduction, and high temperature tolerance. The bonds are formed in a vacuum chamber, using a positioning and loading fixture to compression load the die, and an IR lamp or other heat source. For bonding a silicon die to a silicon substrate, a gold silicon alloy bond is used. Multiple dies can be bonded simultaneously. No scrubbing is required. 1 figure.

Reinraumtechnik für die Medizintechnik

NASA Astrophysics Data System (ADS)

Petek, Max; Jungbluth, Martin; Krampe, Erhard

Die Reinraumtechnik ist heute ein unverzichtbarer Bestandteil bei der Fertigung von Produkten der Life Sciences, den Bereichen Pharma, Lebensmittel, Kosmetik und Medizintechnik. In Anbetracht der langen Historie der Medizintechnik ist sie jedoch eine sehr junge Disziplin. Die Bedeutung von Keimen und die richtige Einschätzung ihrer Größe wurden zwar sehr früh bereits durch Paracelsus erkannt, jedoch wurden daraus noch keine speziellen oder kontinuierlich umgesetzten Hygienevorschriften abgeleitet. Die erste bekannte technische Umsetzung von Hygieneempfehlungen geht auf den Franzosen François Nicolas Appert zurück, der eine aseptische Abfüllmethode für Lebensmittel entwickelte und diese 1810 veröffentlichte [1]. Die erste dokumentierte medizinische Umsetzung stellten Hygienevorschriften für Ärzte dar, die Ignaz Philipp Semmelweis nach 1847 in der Wiener Klinik für Geburtshilfe einführte [2].

Energy Saving Melting and Revert Reduction Technology (E-SMARRT): Mechanical Performance of Dies

DOE Office of Scientific and Technical Information (OSTI.GOV)

R. Allen Miller, Principal Investigator; Kabiri-Bamoradian, Contributors: Khalil; Delgado-Garza, Abelardo

2011-09-13

As a net shape process, die casting is intrinsically efficient and improvements in energy efficiency are strongly dependent on design and process improvements that reduce scrap rates so that more of the total consumed energy goes into acceptable, usable castings. A casting that is distorted and fails to meet specified dimensional requirements is typically remelted but this still results in a decrease in process yield, lost productivity, and increased energy consumption. This work focuses on developing, and expanding the use of, computer modeling methods that can be used to improve the dimensional accuracy of die castings and produce die designsmore » and machine/die setups that reduce rejection rates due to dimensional issues. A major factor contributing to the dimensional inaccuracy of the casting is the elastic deformations of the die cavity caused by the thermo mechanical loads the dies are subjected to during normal operation. Although thermal and die cavity filling simulation are widely used in the industry, structural modeling of the die, particularly for managing part distortion, is not yet widely practiced. This may be due in part to the need to have a thorough understanding of the physical phenomenon involved in die distortion and the mathematical theory employed in the numerical models to efficiently model the die distortion phenomenon. Therefore, two of the goals of this work are to assist in efforts to expand the use of structural modeling and related technologies in the die casting industry by 1) providing a detailed modeling guideline and tutorial for those interested in developing the necessary skills and capability and 2) by developing simple meta-models that capture the results and experience gained from several years of die distortion research and can be used to predict key distortion phenomena of relevance to a die caster with a minimum of background and without the need for simulations. These objectives were met. A detailed modeling tutorial

Rapid solidification processing system for producing molds, dies and related tooling

DOEpatents

McHugh, Kevin M.

2004-06-08

A system for the spray forming manufacturing of near-net-shape molds, dies and related toolings, wherein liquid material such as molten metal, metallic alloys, or polymers are atomized into fine droplets by a high temperature, high velocity gas and deposited onto a pattern. Quenching of the in-flight atomized droplets provides a heat sink, thereby allowing undercooled and partially solidified droplets to be formed in-flight. Composites can be formed by combining the atomized droplets with solid particles such as powders, whiskers or fibers.

Finite element design procedure for correcting the coining die profiles

NASA Astrophysics Data System (ADS)

Alexandrino, Paulo; Leitão, Paulo J.; Alves, Luis M.; Martins, Paulo A. F.

2018-05-01

This paper presents a new finite element based design procedure for correcting the coining die profiles in order to optimize the distribution of pressure and the alignment of the resultant vertical force at the end of the die stroke. The procedure avoids time consuming and costly try-outs, does not interfere with the creative process of the sculptors and extends the service life of the coining dies by significantly decreasing the applied pressure and bending moments. The numerical simulations were carried out in a computer program based on the finite element flow formulation that is currently being developed by the authors in collaboration with the Portuguese Mint. A new experimental procedure based on the stack compression test is also proposed for determining the stress-strain curve of the materials directly from the coin blanks.

Combined Therapy of Septicemia with Ofloxacin and/or Synthetic Trehalose Dicorynomycolate (S-TDCM) in Irradiated and Wounded Mice (Die Kombinierte Therapie der Septikaemie mit Ofloxacin und/oder Synthetischem Trehalose- Dicorynomycolat (S-TDCM) bei Bestrahlten und Verwundeten Maeusen)

DTIC Science & Technology

1989-01-01

COMBINED THERAPY OF SEPTICEMIA WITH OFLOXACIN AND/OR SYNTHETIC TREHALOSE DICORYNOMYCOLATE (S-TDCM)IN IRRADIATED AND WOUNDED MICE * DIE KOMBINIERTE THERAPIE...DER SEPTIKAMIE MIT OFLOXACIN UND ’ODER SYNTHETISCHEM TREHALOSE -DICORYNOMYCOLAT (S-TDCM) BEI BESTRAHLTEN UND VERWUNDETEN MAUSEN GARY S. M4ADONNA. MARY...ceptibility to bacterial infection from either endogenous or exogenous origin. Treatment with ofloxacin or synthetic trehalose dicorynemycolate (S

Effect of mold designs on molten metal behaviour in high-pressure die casting

NASA Astrophysics Data System (ADS)

Ibrahim, M. D.; Rahman, M. R. A.; Khan, A. A.; Mohamad, M. R.; Suffian, M. S. Z. M.; Yunos, Y. S.; Wong, L. K.; Mohtar, M. Z.

2017-04-01

This paper presents a research study conducted in a local automotive component manufacturer that produces aluminium alloy steering housing local and global markets. This study is to investigate the effect of design modification of mold in die casting as to improve the production rate. Design modification is carried out on the casting shot of the mold. Computer flow simulation was carried out to study the flow of molten metal in the mold with respect to the mold design modification. The design parameters of injection speed, die temperature and clamping force has been included in the study. The result of the simulation showed that modifications of casting shot give significant impact towards the molten flow behaviour in casting process. The capabilities and limitations of die casting process simulation to conduct defect analysis had been optimized. This research will enhance the efficiency of the mass production of the industry of die casting with the understanding of defect analysis, which lies on the modification of the mold design, a way early in its stages of production.

Illustration of cross flow of polystyrene melts through a coathanger die

NASA Astrophysics Data System (ADS)

Schöppner, V.; Henke, B.

2015-05-01

To design an optimal coathanger die with a uniform flow rate distribution and low pressure drop, it is essential to understand the flow conditions in the die. This is important because the quality of the product is influenced by the flow velocity and the flow rate distribution. In extrusion dies, cross flows also occur in addition to the main flow, which flow perpendicular to the main flow. This results in pressure gradients in the extrusion direction, which have an influence on flow distribution and pressure drop in the die. In recent decades, quantitative representation and analysis of physical flow processes have made considerable progress in predicting the weather, developing drive technologies and designing aircraft using simulation methods and lab trials. Using the flow-line method, the flow is analyzed in flat film extrusion dies with a rectangular cross-section, in particular cross flows. The simplest method to visualize the flow is based on the measurement of obstacle orientation in the flow field by adding individual particles. A near-surface flow field can be visualized by using wool or textile yarns. By sticking thin, frayed at the ends of strands of wool surface that is to be examined cross flows, near-wall profiles of the flow and vortex and separation regions can be visualized. A further possibility is to add glass fibers and analyze the fiber orientation by microscopy and x-ray analysis. In this paper the influence of process parameters (e.g. melt temperatures and throughput) on cross flow and fiber orientation is described.

Contoured Orifice for Silicon-Ribbon Die

NASA Technical Reports Server (NTRS)

Mackintosh, B. H.

1985-01-01

Die configuration encourages purity and stable growth. Contour of die orifice changes near ribbon edges. As result, silicon ribbon has nearly constant width and little carbon contamination. Die part of furnace being developed to produce high-quality, low-cost material for solar cells.

Dying with motor neurone disease, what can we learn from family caregivers?

PubMed Central

Ray, Robin A.; Brown, Janice; Street, Annette F.

2012-01-01

Abstract Background  Increasingly, people with neurodegenerative illness are cared for at home until close to death. Yet, discussing the reality of dying remains a social taboo. Objective  To examine the ways, family caregivers of people living with motor neurone disease (MND) experienced the dying of their relative and to identify how health practitioners can better prepare families for end‐of‐life care. Design  Secondary analysis was undertaken on data sets generated from two longitudinal qualitative studies employing similar data collection and analysis methods. Combining data sets increased participant numbers in a low incidence disease group. Setting and participants  Primary studies were undertaken with family caregivers in England and Australia. Interview and observational data were collected mostly in home. Participants who discussed dying and death formed the sample for secondary analysis. Results  Combined data revealed four major themes: planning for end of life, unexpected dying, dignity in the dying body and positive end to MND. Despite short survival predictions, discussions among family members about dying were often sporadic and linked to loss of hope. Effective planning for death assisted caregivers to manage the final degenerative processes of dying. When plans were not effectively communicated or enacted, capacity to preserve personhood was reduced. Discussion and Conclusion  Returning death and dying to social discourse will raise the level of community awareness and normalize conversations about end‐of‐life care. Strategies for on‐going, effective communication that facilitates advance care planning among patients, their families and practitioners are essential to improve dying and death for people with MND and their family caregivers. PMID:22512686

Production of High Quality Die Steels from Large ESR Slab Ingots

NASA Astrophysics Data System (ADS)

Geng, Xin; Jiang, Zhou-hua; Li, Hua-bing; Liu, Fu-bin; Li, Xing

With the rapid development of manufacture industry in China, die steels are in great need of large slab ingot of high quality and large tonnage, such as P20, WSM718R and so on. Solidification structure and size of large slab ingots produced with conventional methods are not satisfied. However, large slab ingots manufactured by ESR process have a good solidification structure and enough section size. In the present research, the new slab ESR process was used to produce the die steels large slab ingots with the maximum size of 980×2000×3200mm. The compact and sound ingot can be manufactured by the slab ESR process. The ultra-heavy plates with the maximum thickness of 410 mm can be obtained after rolling the 49 tons ingots. Due to reducing the cogging and forging process, the ESR for large slab ingots process can increase greatly the yield and production efficiency, and evidently cut off product costs.

Strong resilience of soil respiration components to drought-induced die-off resulting in forest secondary succession.

PubMed

Barba, Josep; Curiel Yuste, Jorge; Poyatos, Rafael; Janssens, Ivan A; Lloret, Francisco

2016-09-01

How forests cope with drought-induced perturbations and how the dependence of soil respiration on environmental and biological drivers is affected in a warming and drying context are becoming key questions. The aims of this study were to determine whether drought-induced die-off and forest succession were reflected in soil respiration and its components and to determine the influence of climate on the soil respiration components. We used the mesh exclusion method to study seasonal variations in soil respiration (R S) and its components: heterotrophic (R H) and autotrophic (R A) [further split into fine root (R R) and mycorrhizal respiration (R M)] in a mixed Mediterranean forest where Scots pine (Pinus sylvestris L.) is undergoing a drought-induced die-off and is being replaced by holm oak (Quercus ilex L.). Drought-induced pine die-off was not reflected in R S nor in its components, which denotes a high functional resilience of the plant and soil system to pine die-off. However, the succession from Scots pine to holm oak resulted in a reduction of R H and thus in an important decrease of total respiration (R S was 36 % lower in holm oaks than in non-defoliated pines). Furthermore, R S and all its components were strongly regulated by soil water content-and-temperature interaction. Since Scots pine die-off and Quercus species colonization seems to be widely occurring at the driest limit of the Scots pine distribution, the functional resilience of the soil system over die-off and the decrease of R S from Scots pine to holm oak could have direct consequences for the C balance of these ecosystems.

Dying with Dementia in Long-Term Care

ERIC Educational Resources Information Center

Sloane, Philip D.; Zimmerman, Sheryl; Williams, Christianna S.; Hanson, Laura C.

2008-01-01

Purpose: To better understand the experiences and potential unmet need of persons who die in long-term care. Design and Methods: We conducted after-death interviews with staff who had cared for 422 decedents with dementia and 159 who were cognitively intact and received terminal care in U.S. nursing homes (NHs) or residential care-assisted living…

Regional vegetation die-off in response to global-change-type drought

USGS Publications Warehouse

Breshears, D.D.; Cobb, N.S.; Rich, P.M.; Price, K.P.; Allen, Craig D.; Balice, R.G.; Romme, W.H.; Kastens, J.H.; Floyd, M. Lisa; Belnap, J.; Anderson, J.J.; Myers, O.B.; Meyer, Clifton W.

2005-01-01

Future drought is projected to occur under warmer temperature conditions as climate change progresses, referred to here as global-change-type drought, yet quantitative assessments of the triggers and potential extent of drought-induced vegetation die-off remain pivotal uncertainties in assessing climate-change impacts. Of particular concern is regional-scale mortality of overstory trees, which rapidly alters ecosystem type, associated ecosystem properties, and land surface conditions for decades. Here, we quantify regional-scale vegetation die-off across southwestern North American woodlands in 2002-2003 in response to drought and associated bark beetle infestations. At an intensively studied site within the region, we quantified that after 15 months of depleted soil water content, >90% of the dominant, overstory tree species (Pinus edulis, a piñon) died. The die-off was reflected in changes in a remotely sensed index of vegetation greenness (Normalized Difference Vegetation Index), not only at the intensively studied site but also across the region, extending over 12,000 km2 or more; aerial and field surveys confirmed the general extent of the die-off. Notably, the recent drought was warmer than the previous subcontinental drought of the 1950s. The limited, available observations suggest that die-off from the recent drought was more extensive than that from the previous drought, extending into wetter sites within the tree species' distribution. Our results quantify a trigger leading to rapid, drought-induced die-off of overstory woody plants at subcontinental scale and highlight the potential for such die-off to be more severe and extensive for future global-change-type drought under warmer conditions.

Regional vegetation die-off in response to global-change-type drought

PubMed Central

Breshears, David D.; Cobb, Neil S.; Rich, Paul M.; Price, Kevin P.; Allen, Craig D.; Balice, Randy G.; Romme, William H.; Kastens, Jude H.; Floyd, M. Lisa; Belnap, Jayne; Anderson, Jesse J.; Myers, Orrin B.; Meyer, Clifton W.

2005-01-01

Future drought is projected to occur under warmer temperature conditions as climate change progresses, referred to here as global-change-type drought, yet quantitative assessments of the triggers and potential extent of drought-induced vegetation die-off remain pivotal uncertainties in assessing climate-change impacts. Of particular concern is regional-scale mortality of overstory trees, which rapidly alters ecosystem type, associated ecosystem properties, and land surface conditions for decades. Here, we quantify regional-scale vegetation die-off across southwestern North American woodlands in 2002-2003 in response to drought and associated bark beetle infestations. At an intensively studied site within the region, we quantified that after 15 months of depleted soil water content, >90% of the dominant, overstory tree species (Pinus edulis, a piñon) died. The die-off was reflected in changes in a remotely sensed index of vegetation greenness (Normalized Difference Vegetation Index), not only at the intensively studied site but also across the region, extending over 12,000 km2 or more; aerial and field surveys confirmed the general extent of the die-off. Notably, the recent drought was warmer than the previous subcontinental drought of the 1950s. The limited, available observations suggest that die-off from the recent drought was more extensive than that from the previous drought, extending into wetter sites within the tree species' distribution. Our results quantify a trigger leading to rapid, drought-induced die-off of overstory woody plants at subcontinental scale and highlight the potential for such die-off to be more severe and extensive for future global-change-type drought under warmer conditions. PMID:16217022

Extrusion die and method

DOEpatents

Lipp, G. Daniel

1994-05-03

A method and die apparatus for manufacturing a honeycomb body of triangular cell cross-section and high cell density, the die having a combination of (i) feedholes feeding slot intersections and (ii) feedholes feeding slot segments not supplied from slot intersections, whereby a reduction in feedhole count is achieved while still retaining good extrusion efficiency and extrudate uniformity.

Imagining the alternatives to life prolonging treatments: elders' beliefs about the dying experience.

PubMed

Winter, Laraine; Parker, Barbara; Schneider, Melissa

2007-08-01

Deciding for or against a life-prolonging treatment represents a choice between prolonged life and death. When the death alternative is not described, individuals must supply their own assumptions. How do people imagine the experience of dying? We asked 40 elderly people open-ended questions about dying without 4 common life-prolonging treatments, eliciting beliefs about pain, length of time, loneliness, and palliative care. Beliefs were diverse, loneliness was commonly assumed, and palliation was rarely mentioned spontaneously. Results underscore needs for improved understanding of the dying process and palliative care and for fuller communication between patients and healthcare providers.

WAMA: a method of optimizing reticle/die placement to increase litho cell productivity

NASA Astrophysics Data System (ADS)

Dor, Amos; Schwarz, Yoram

2005-05-01

This paper focuses on reticle/field placement methodology issues, the disadvantages of typical methods used in the industry, and the innovative way that the WAMA software solution achieves optimized placement. Typical wafer placement methodologies used in the semiconductor industry considers a very limited number of parameters, like placing the maximum amount of die on the wafer circle and manually modifying die placement to minimize edge yield degradation. This paper describes how WAMA software takes into account process characteristics, manufacturing constraints and business objectives to optimize placement for maximum stepper productivity and maximum good die (yield) on the wafer.

Differentiating suicide decedents who died using firearms from those who died using other methods.

PubMed

Anestis, Michael D; Khazem, Lauren R; Anestis, Joye C

2017-06-01

Studies have documented a link between gun ownership and suicide, but little is known about characteristics of those most likely to use a gun in a suicide attempt rather than alternative methods. We examined which factors differentiate suicide decedents who died using a gun from those who died by other methods. We further examined whether such findings are consistent within the subcomponent of our larger sample comprised entirely of gun owning suicide decedents. Data reflect 267 suicide decedents, with data provided by individuals who identified as having lost someone to suicide (loss survivors). Within the full sample, a higher proportion of gun-owning and male suicide decedents died by firearm. Further, individuals who had previously discussed suicide or engaged in one or more non-lethal suicide attempts were less likely to die by suicide using a gun. Within the subsample of gun owning suicide decedents, a greater proportion of decedents who stored guns at home and in unsecure locations died from self-inflected gunshot wounds. These findings add clarity to the relationship between firearm ownership and death by suicide at the individual level. Furthermore, these findings are consistent with the notion that means safety implementation may represent a vital suicide prevention tool. Copyright © 2017. Published by Elsevier B.V.

Mis-specified cells die by an active gene-directed process, and inhibition of this death results in cell fate transformation in Drosophila

PubMed Central

Werz, Christian; Lee, Tom V.; Lee, Peter L.; Lackey, Melinda; Bolduc, Clare; Stein, David S.; Bergmann, Andreas

2009-01-01

Summary Incorrectly specified or mis-specified cells often undergo cell death or are transformed to adopt a different cell fate during development. The underlying cause for this distinction is largely unknown. In many developmental mutants in Drosophila, large numbers of mis-specified cells die synchronously, providing a convenient model for analysis of this phenomenon. The maternal mutant bicoid is particularly useful model with which to address this issue because its mutant phenotype is a combination of both transformation of tissue (acron to telson) and cell death in the presumptive head and thorax regions. We show that a subset of these mis-specified cells die through an active gene-directed process involving transcriptional upregulation of the cell death inducer hid. Upregulation of hid also occurs in oskar mutants and other segmentation mutants. In hid bicoid double mutants, mis-specified cells in the presumptive head and thorax survive and continue to develop, but they are transformed to adopt a different cell fate. We provide evidence that the terminal torso signaling pathway protects the mis-specified telson tissue in bicoid mutants from hid-induced cell death, whereas mis-specified cells in the head and thorax die, presumably because equivalent survival signals are lacking. These data support a model whereby mis-specification can be tolerated if a survival pathway is provided, resulting in cellular transformation. PMID:16280349

Declarations on euthanasia and assisted dying.

PubMed

Inbadas, Hamilton; Zaman, Shahaduz; Whitelaw, Sandy; Clark, David

2017-10-01

Declarations on end-of-life issues are advocacy interventions that seek to influence policy, raise awareness and call others to action. Despite increasing prominence, they have attracted little attention from researchers. This study tracks the emergence, content, and purpose of declarations concerned with assisted dying and euthanasia, in the global context. The authors identified 62 assisted dying/euthanasia declarations covering 1974-2016 and analyzed them for originating organization, geographic scope, format, and stated viewpoint on assisted dying/euthanasia. The declarations emerged from diverse organizational settings and became more frequent over time. Most opposed assisted dying/euthanasia.

Declarations on euthanasia and assisted dying

PubMed Central

Inbadas, Hamilton; Zaman, Shahaduz; Whitelaw, Sandy; Clark, David

2017-01-01

ABSTRACT Declarations on end-of-life issues are advocacy interventions that seek to influence policy, raise awareness and call others to action. Despite increasing prominence, they have attracted little attention from researchers. This study tracks the emergence, content, and purpose of declarations concerned with assisted dying and euthanasia, in the global context. The authors identified 62 assisted dying/euthanasia declarations covering 1974–2016 and analyzed them for originating organization, geographic scope, format, and stated viewpoint on assisted dying/euthanasia. The declarations emerged from diverse organizational settings and became more frequent over time. Most opposed assisted dying/euthanasia. PMID:28398131

Coping with Dying: Lessons That We Should and Should Not Learn from the Work of Elisabeth Kubler-Ross.

ERIC Educational Resources Information Center

Corr, Charles A.

1993-01-01

Appraises work of Elisabeth Kubler-Ross in area of coping with dying. Suggests lessons from that work. Draws broad conclusions about processes involved in coping with dying, argues on behalf of need to develop better theoretical models to explicate what is involved in coping with dying, and suggests requirements for model. (Author/NB)

Microstructure and Properties of Cobalt-and Zinc-Containing Magnetic Magnesium Alloys Processed by High-Pressure Die Casting

NASA Astrophysics Data System (ADS)

Klose, Christian; Demminger, Christian; Maier, Hans Jürgen

The inherent magnetic properties of lightweight alloys based on magnesium and cobalt offer a novel way in order to measure mechanical loads throughout the entire structural component using the magnetoelastic effect. Because the solubility of cobalt in the magnesium matrix is negligible, the magnetic properties mainly originate from Co-rich precipitates. Thus, the size and distribution of Co-containing phases within the alloy's microstructure wields a major influence on the amplitude of the load-sensitive properties which can be measured by employing the harmonic analysis of eddy-current signals. In this study, Mg-Co-based alloys are produced by several casting methods which allow the application of different cooling rates, e.g. gravity die casting and high-pressure die casting. The differences between the manufactured alloys' micro- and phase structures are compared depending on the applied cooling rate and the superior magnetic and mechanical properties of the high-pressure die cast material are demonstrated.

Dying, mourning, and spirituality: a psychological perspective.

PubMed

Marrone, R

1999-09-01

Based in an unfortunate tradition that stretches back in time to Watson's behaviorism and Freud's psychoanalysis, psychology has tended to reject and to pathologize matters of the spirit. In the past 30 years, however, with the advent of what has been termed the cognitive revolution, psychology has greatly expanded the scope of its subject matter. Psychologists and thanatologists have begun to unravel the cognitive underpinnings of our assumptive world and the transformation of those underpinnings in times of crisis and stress. This article examines the cognitive basis of the spiritual experience and the use of cognitive assimilation, accommodation strategies during the process of mourning the death of a loved one, as well as during the process of living our own dying. Of special importance to mental health professionals and clergy, new research on dying, mourning, and spirituality suggests that the specific ways in which people rediscover meaning--such as belief in traditional religious doctrine, the afterlife, reincarnation, philanthropy, or a spiritual order to the universe--may be less important than the process itself. In other words, in the midst of dealing with profound loss in our lives, the ability to reascribe meaning to a changed world through spiritual transformation, religious conversion, or existential change may be more significant than the specific content by which that need is filled.

[The meaning of dying with dignity from caregivers perspective: a phenomenological study].

PubMed

Ibáñez-Masero, Olivia; Ortega-Galán, Ángela M; Carmona-Rega, M Inés; Ruiz-Fernández, M Dolores; Cabrera-Troya, José; García-Cisneros, Rogelio; Medina, Fernando Relinque

To explore the meaning of dying with dignity from the perspective of the direct witnesses who have accompanied this process in dying people from Andalusia. Phenomenological study conducted in different centres, which including analysing the transcriptions of the dialogues from discussion groups with 40 participants in five provinces in Southern Spain. The data was analysed using the Van Manen proposal and Atlas Ti 7.0 program was applied as a software tool. Being in the company of loved ones is noted as a key element in the perception of a dignified death. The following elements, according to a priority order, were also pointed out: relief of suffering, a good professional care, decision making ability, and the opportunity to consider their spiritual dimension. Achievement of their Living Wills is hardly mentioned. The essential elements defined in the Death with Dignity Law, 2/2010 are confirmed as being true (without suffering, with company, respecting living wills, having possibilities of the farewell, and the transcendental meaning of the death process). Caregivers, at the end of life, give priority to psychological aspects, underlying the need of company, a farewell of the loved ones, and a good professional care on the physical aspects. The promotion of the dignified Death Law and Living Wills are still being developed. Copyright © 2016 Elsevier España, S.L.U. All rights reserved.

Recognizing dying in terminal illness.

PubMed

Taylor, Paul M; Johnson, Miriam

2011-08-01

Recognizing dying in terminally ill patients is a complex clinical skill. This article outlines the approach to the decision, common difficulties encountered in patients with both malignant and non-malignant disease, and a simple approach to considering the question 'Is this patient dying?'

Dying: A universal human experience?

PubMed

Bregman, L

1989-03-01

This paper explores the question, "Is there a universal psychological experience suffered by all dying persons?" a question to which the popular theory of Kübler-Ross presupposes an affirmative answer. Our answer takes three steps: first, a comparison between the Kübler-Ross model of dying and that of the late medievalBook of the Craft of Dying centered upon the five Kübler-Ross "stages"; second, a philosophical critique of the terms of this comparison; and third, a revised look at the alleged similarities between the two models, providing a deeper look at the moral and spiritual assumptions behind each.

ELID grinding characteristics of large stamping die for Wolter mirror.

PubMed

Yin, Shaohui; Ohmori, Hitoshi; Liu, Qing; Morita, Shinnya; Chen, Fengjun; Asami, Muneaki; Fan, Yufeng

2009-01-01

An ultra-precision ELID grinding of large stamping dies of Wolter mirror for X-ray telescope was presented in this paper. The large stamping dies (S55C) with confocal paraboloid and hyperboloid was ground by ELID arc-enveloped grinding. In this ELID grinding system, cast iron fiber bonded (CIFB) diamond wheels were controlled by 3-dimentional ways to scan the work-piece and generate required surfaces. Its grinding characteristics such as attainable form accuracy, surface roughness were investigated. Furthermore, some measures to improve form accuracy were discussed and verified such as truing, compensating, and on-machine measuring.

Design and Analysis of a Forging Die for Manufacturing of Multiple Connecting Rods

NASA Astrophysics Data System (ADS)

Megharaj, C. E.; Nagaraj, P. M.; Jeelan Pasha, K.

2016-09-01

This paper demonstrates to utilize the hammer capacity by modifying the die design such that forging hammer can manufacture more than one connecting rod in a given forging cycle time. To modify the die design study is carried out to understand the parameters that are required for forging die design. By considering these parameters, forging die is designed using design modelling tool solid edge. This new design now can produce two connecting rods in same capacity hammer. The new design is required to validate by verifying complete filing of metal in die cavities without any defects in it. To verify this, analysis tool DEFORM 3D is used in this project. Before start of validation process it is require to convert 3D generated models in to. STL file format to import the models into the analysis tool DEFORM 3D. After importing these designs they are analysed for material flow into the cavities and energy required to produce two connecting rods in new forging die design. It is found that the forging die design is proper without any defects and also energy graph shows that the forging energy required to produce two connecting rods is within the limit of that hammer capacity. Implementation of this project increases the production of connecting rods by 200% in less than previous cycle time.

["Good dying"--definition and current state of research].

PubMed

Hutter, Nico; Stößel, Ulrich; Meffert, Cornelia; Körner, Mirjam; Bozzaro, Claudia; Becker, Gerhild; Baumeister, Harald

2015-08-01

The advances of modern medicine did not only result in prolongation of life expectancy, but also led to a shift from dying at home to dying in public institutions. In western countries most people die at advanced age in medical facilities. Hence, the question regarding the conditions, which should be provided by society and especially medicine, to allow terminally ill people to experience "good dying" is substantial. For this purpose, an examination of patients', family members' and health care providers' understanding of the term " good dying" is required. The present paper aims at shedding light on the term "good dying" and to summarize the current state of research. Therefore, the attributes of "good dying" will be described from the perspectives of patients, family members and health care providers, which are discussed and examined in current medical-sociological research. These attributes can be illustrated on three dimensions: Quality of life at the end of life (e. g. pain relief, mental well-being), quality of dying (e. g. avoiding prolonged dying, autonomy, presence of relatives) and quality of health care at the end of life (e. g. patient-oriented health care, positive communication between health care providers and patients, availability of guidelines). Although the attributes of "good dying" are described in detail in the existing literature, further studies have to clarify the relevance and impact of these attributes as predictors of "good dying". © Georg Thieme Verlag KG Stuttgart · New York.

Bereits nach Ablauf der Halbwertszeit droht der vollständige Zerfall Die britische Atomic Scientists’ Association, die Ideologie der „objektiven” Wissenschaft und die H-Bombe

NASA Astrophysics Data System (ADS)

Laucht, Christoph

Präsident Harry Trumans Verlautbarung vom 31.1.1950, seine Regierung wolle die Entwicklung der Wasserstoffbombe vorantreiben, fand große Beachtung in den britischen Medien. Die illustrierte Zeitschrift Picture Post widmete der HBombe einen Artikel, der unter anderem kurze Stellungnahmen der britischen Atomwissenschaftler Eric Burhop, Kathleen Lonsdale, Harrie Massey, Rudolf Peierls und Maurice Pryce enthielt, die alle Mitglieder der Atomic Scientists' Association (ASA) waren.

Die Deformation Measurement System during Sheet Metal Forming

NASA Astrophysics Data System (ADS)

Funada, J.; Takahashi, S.; Fukiharu, H.

2011-08-01

In order to reduce affection to the earth environment, it is necessary to lighten the vehicles. For this purpose, high tensile steels are applied. Because of high strength, high forming force is required for producing automotive sheet metal parts. In this situation, since the dies are elastic, they are deformed during forming parts. For reducing die developing period, sheet metal forming simulation is widely applied. In the numerical simulation, rigid dies are usually used for shortening computing time. It means that the forming conditions in the actual forming and the simulation are different. It will make large errors in the results between actual forming and simulation. It can be said that if contact pressure between dies and a sheet metal in the simulation can be reproduced in the actual forming, the differences of forming results between them can also been reduced. The basic idea is to estimate die shape which can produce the same distribution as computed from simulation with rigid dies. In this study, die deformation analyses with Finite Element Method as basic technologies are evaluated. For example, simple shape and actual dies elastic contact problems were investigated. The contact width between simple shape dies was investigated. The computed solutions were in good agreement with experimental results. The one case of the actual dies in two cases was also investigated. Bending force was applied to the blank holder with a mechanical press machine. The methodology shown with applying inductive displacement sensor for measuring die deformation during applying force was also proposed.

Robot-based additive manufacturing for flexible die-modelling in incremental sheet forming

NASA Astrophysics Data System (ADS)

Rieger, Michael; Störkle, Denis Daniel; Thyssen, Lars; Kuhlenkötter, Bernd

2017-10-01

The paper describes the application concept of additive manufactured dies to support the robot-based incremental sheet metal forming process (`Roboforming') for the production of sheet metal components in small batch sizes. Compared to the dieless kinematic-based generation of a shape by means of two cooperating industrial robots, the supporting robot models a die on the back of the metal sheet by using the robot-based fused layer manufacturing process (FLM). This tool chain is software-defined and preserves the high geometrical form flexibility of Roboforming while flexibly generating support structures adapted to the final part's geometry. Test series serve to confirm the feasibility of the concept by investigating the process challenges of the adhesion to the sheet surface and the general stability as well as the influence on the geometric accuracy compared to the well-known forming strategies.

Einführung in die Technische Chemie

NASA Astrophysics Data System (ADS)

Behr, Arno; Agar, David W.; Jörissen, Jakob

Die "Technische Chemie" ist ein Lehrfach an Universitäten und Hochschulen. Nach dem die Studierenden der Chemie in den ersten Semestern ihres Studiums ausrei chen de theoretische Kenntnisse in Allgemeiner, Anorganischer, Organischer und Physikalischer Chemie erlangt haben, soll die Technische Chemie einen Blick auf die praktische Anwendung dieser Naturwissenschaft in unserer Wirtschaft lenken. Es gibt keine "biologische Industrie", "physikalische Industrie" oder "mathematische Industrie", wohl aber seit über 150 Jahren eine "chemische Industrie", die in dieser lan gen Zeit zahlreiche chemische Prozesse entwickelt und dazu vielfältige Methoden erarbeitet hat. Das Lehrfach Technische Chemie gibt einen Überblick über diese Pro zesse und Methoden und erleichtert dadurch den Schritt von der Universität zur be ruflichen Praxis.

Communication About Dying, Death, and Bereavement: A Systematic Review of Children's Literature

PubMed Central

Arruda-Colli, Marina N. F.; Weaver, Meaghann S.

2017-01-01

Abstract Background: Children's books have the potential to facilitate communication about death for children living with a serious illness and for children coping with the death of a loved one. Objectives: This study examines the content of children's literature relevant to the topic of dying and death and identifies books providers can share with children and their families. Design: A search of children's literature was conducted using four electronic databases and one additional search engine using the word “Death” or “Dying.” Storybooks about dying, death, and bereavement published in English, French, or Spanish between 1995 and 2015 were included. Measurements: Each book underwent content analysis by at least two independent reviewers. Strict PRISMA standard was followed. Full protocol is available as PROSPERO #CRD42016042129. Results: Two hundred ten books met inclusion criteria. The dying subject was primarily a grandparent (n = 78) or pet (n = 44). Books on the experience of a child dying were scarce (n = 5). The word death or dying was used in 75% of the books (n = 158), while others utilized euphemisms. The majority of books featured animals (n = 40) or Caucasian subjects (n = 122) and included spiritual elements such as heaven (n = 122). Less than one-quarter of the books included tools for readers to address the topic of death. Conclusions: Storybooks can be a helpful tool to introduce communication about dying and death with children. Gaps exist in current children's literature to effectively enable children to reflect on their own dying process. A general summary of available books is provided to assist those caring for children and families facing end-of-life issues. PMID:28346862

Rapid Prototyping of Slot Die Devices for Roll to Roll Production of EL Fibers

PubMed Central

Bellingham, Alyssa; Bromhead, Nicholas; Fontecchio, Adam

2017-01-01

There is a growing interest in fibers supporting optoelectrical properties for textile and wearable display applications. Solution-processed electroluminescent (EL) material systems can be continuously deposited onto fiber or yarn substrates in a roll-to-roll process, making it easy to scale manufacturing. It is important to have precise control over layer deposition to achieve uniform and reliable light emission from these EL fibers. Slot-die coating offers this control and increases the rate of EL fiber production. Here, we report a highly adaptable, cost-effective 3D printing model for developing slot dies used in automatic coating systems. The resulting slot-die coating system enables rapid, reliable production of alternating current powder-based EL (ACPEL) fibers and can be adapted for many material systems. The benefits of this system over dip-coating for roll-to-roll production of EL fibers are demonstrated in this work. PMID:28772954

Rapid Prototyping of Slot Die Devices for Roll to Roll Production of EL Fibers.

PubMed

Bellingham, Alyssa; Bromhead, Nicholas; Fontecchio, Adam

2017-05-29

There is a growing interest in fibers supporting optoelectrical properties for textile and wearable display applications. Solution-processed electroluminescent (EL) material systems can be continuously deposited onto fiber or yarn substrates in a roll-to-roll process, making it easy to scale manufacturing. It is important to have precise control over layer deposition to achieve uniform and reliable light emission from these EL fibers. Slot-die coating offers this control and increases the rate of EL fiber production. Here, we report a highly adaptable, cost-effective 3D printing model for developing slot dies used in automatic coating systems. The resulting slot-die coating system enables rapid, reliable production of alternating current powder-based EL (ACPEL) fibers and can be adapted for many material systems. The benefits of this system over dip-coating for roll-to-roll production of EL fibers are demonstrated in this work.

Clinical decision making in the recognition of dying: a qualitative interview study.

PubMed

Taylor, Paul; Dowding, Dawn; Johnson, Miriam

2017-01-25

Recognising dying is an essential clinical skill for general and palliative care professionals alike. Despite the high importance, both identification and good clinical care of the dying patient remains extremely difficult and often controversial in clinical practice. This study aimed to answer the question: "What factors influence medical and nursing staff when recognising dying in end-stage cancer and heart failure patients?" This study used a descriptive approach to decision-making theory. Participants were purposively sampled for profession (doctor or nurse), specialty (cardiology or oncology) and grade (senior vs junior). Recruitment continued until data saturation was reached. Semi-structured interviews were conducted with NHS medical and nursing staff in an NHS Trust which contained cancer and cardiology tertiary referral centres. An interview schedule was designed, based on decision-making literature. Interviews were audio-recorded and transcribed and analysed using thematic framework. Data were managed with Atlas.ti. Saturation was achieved with 19 participants (7 seniors; 8 intermediate level staff; 4 juniors). There were 11 oncologists (6 doctors, 5 nurses) and 8 cardiologists (3 doctors, 5 nurses). Six themes were generated: information used; decision processes; modifying factors; implementation; reflecting on decisions and related decisions. The decision process described was time-dependent, ongoing and iterative, and relies heavily on intuition. This study supports the need to recognise the strengths and weaknesses of expertise and intuition as part of the decision process, and of placing the recognition of dying in a time-dependent context. Clinicians should also be prepared to accept and convey the uncertainty surrounding these decisions, both in practice and in communication with patients and carers.

Deburring die-castings by wet vibratory plant

NASA Astrophysics Data System (ADS)

Loeschbart, H. M.

1980-02-01

A wet vibratory procedure for the removal of burrs from die castings is described. In this process synthetic abrasive chips and detergent solutions are agitated with the work in such a way as to produce a spiral circulatory movement. Details of various forms of vibrator basin and shapes of abrasive are illustrated. The automation of deburring is illustrated through the application of vibrators of spiral design in combination with transport and drying devices.

Deburring die-castings by wet vibratory plant

NASA Technical Reports Server (NTRS)

Loeschbart, H. M.

1980-01-01

A wet vibratory procedure for the removal of burrs from die castings is described. In this process synthetic abrasive chips and detergent solutions are agitated with the work in such a way as to produce a spiral circulatory movement. Details of various forms of vibrator basin and shapes of abrasive are illustrated. The automation of deburring is illustrated through the application of vibrators of spiral design in combination with transport and drying devices.

Removing function model and experiments on ultrasonic polishing molding die

NASA Astrophysics Data System (ADS)

Huang, Qitai; Ni, Ying; Yu, Jingchi

2010-10-01

Low temperature glass molding technology is the main method on volume-producing high precision middle and small diameter optical cells in the future. While the accuracy of the molding die will effect the cell precision, so the high precision molding die development is one of the most important part of the low temperature glass molding technology. The molding die is manufactured from high rigid and crisp metal alloy, with the ultrasonic vibration character of high vibration frequency and concentrative energy distribution; abrasive particles will impact the rigid metal alloy surface with very high speed that will remove the material from the work piece. Ultrasonic can make the rigid metal alloy molding die controllable polishing and reduce the roughness and surface error. Different from other ultrasonic fabrication method, untouched ultrasonic polishing is applied on polish the molding die, that means the tool does not touch the work piece in the process of polishing. The abrasive particles vibrate around the balance position with high speed and frequency under the drive of ultrasonic vibration in the liquid medium and impact the workspace surface, the energy of abrasive particles come from ultrasonic vibration, while not from the direct hammer blow of the tool. So a nummular vibrator simple harmonic vibrates on an infinity plane surface is considered as a model of ultrasonic polishing working condition. According to Huygens theory the sound field distribution on a plane surface is analyzed and calculated, the tool removing function is also deduced from this distribution. Then the simple point ultrasonic polishing experiment is proceeded to certificate the theory validity.

Acceptance of dying: a discourse analysis of palliative care literature.

PubMed

Zimmermann, Camilla

2012-07-01

The subject of death denial in the West has been examined extensively in the sociological literature. However, there has not been a similar examination of its "opposite", the acceptance of death. In this study, I use the qualitative method of discourse analysis to examine the use of the term "acceptance" of dying in the palliative care literature from 1970 to 2001. A Medline search was performed by combining the text words "accept or acceptance" with the subject headings "terminal care or palliative care or hospice care", and restricting the search to English language articles in clinical journals discussing acceptance of death in adults. The 40 articles were coded and analysed using a critical discourse analysis method. This paper focuses on the theme of acceptance as integral to palliative care, which had subthemes of acceptance as a goal of care, personal acceptance of healthcare workers, and acceptance as a facilitator of care. For patients and families, death acceptance is a goal that they can be helped to attain; for palliative care staff, acceptance of dying is a personal quality that is a precondition for effective practice. Acceptance not only facilitates the dying process for the patient and family, but also renders care easier. The analysis investigates the intertextuality of these themes with each other and with previous texts. From a Foucauldian perspective, I suggest that the discourse on acceptance of dying represents a productive power, which disciplines patients through apparent psychological and spiritual gratification, and encourages participation in a certain way to die. Copyright © 2012 Elsevier Ltd. All rights reserved.

25 CFR 301.4 - Application of dies.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 2 2010-04-01 2010-04-01 false Application of dies. 301.4 Section 301.4 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR NAVAJO, PUEBLO, AND HOPI SILVER AND TURQUOISE PRODUCTS; STANDARDS § 301.4 Application of dies. Dies are to be applied to the object with the aid of...

Der Einfluss der Digitalisierung auf die Organisation eines Unternehmens

NASA Astrophysics Data System (ADS)

Walter, Wolfram M.

Die Digitalisierung schreitet mit großen Schritten voran. Dies wirkt sich nicht nur auf die Gesellschaft im Grundsatz, sondern auch auf das Verhalten der Kunden aus. Neue Kommunikationswege beschleunigen die Interaktion zwischen Unternehmen und Verbraucher. Im Vergleich mit großen Internetfirmen werden etablierte Dienstleistungsunternehmen - vom Energieversorger bis zu Versicherungen - stark unter Druck gesetzt, sich noch intensiver mit dem Kundenservice auseinanderzusetzen. Dies wird nur möglich sein, wenn sich die Organisationen entsprechend positionieren und sich frühzeitig auf die Veränderungen einstellen. Hieraus ergeben sich mehr Chancen als Risiken, zumal es nicht nur neue Prozesse, sondern auch neue Berufsbilder geben wird.

Perovskite solar cells in N-I-P structure with four slot-die-coated layers

PubMed Central

Burkitt, Daniel; Searle, Justin

2018-01-01

The fabrication of perovskite solar cells in an N-I-P structure with compact titanium dioxide blocking, mesoporous titanium dioxide scaffold, single-step perovskite and hole-transport layers deposited using the slot-die coating technique is reported. Devices on fluorine-doped tin oxide-coated glass substrates with evaporated gold top contacts and four slot-die-coated layers are demonstrated, and best cells reach stabilized power conversion efficiencies of 7%. This work demonstrates the suitability of slot-die coating for the production of layers within this perovskite solar cell stack and the potential to transfer to large area and roll-to-roll manufacturing processes. PMID:29892402

Numerical simulation and experiment on multilayer stagger-split die.

PubMed

Liu, Zhiwei; Li, Mingzhe; Han, Qigang; Yang, Yunfei; Wang, Bolong; Sui, Zhou

2013-05-01

A novel ultra-high pressure device, multilayer stagger-split die, has been constructed based on the principle of "dividing dies before cracking." Multilayer stagger-split die includes an encircling ring and multilayer assemblages, and the mating surfaces of the multilayer assemblages are mutually staggered between adjacent layers. In this paper, we investigated the stressing features of this structure through finite element techniques, and the results were compared with those of the belt type die and single split die. The contrast experiments were also carried out to test the bearing pressure performance of multilayer stagger-split die. It is concluded that the stress distributions are reasonable and the materials are utilized effectively for multilayer stagger-split die. And experiments indicate that the multilayer stagger-split die can bear the greatest pressure.

Modeling and Analysis of Deformation for Spiral Bevel Gear in Die Quenching Based on the Hardenability Variation

NASA Astrophysics Data System (ADS)

Zhang, Yingtao; Wang, Gang; Shi, Wankai; Yang, Lin; Li, Zhichao

2017-07-01

Spiral bevel gears are widely used to transmit energy between intersecting axes. The strength and fatigue life of the gears are improved by carburizing and quenching. A die quenching process is used to control the deformation of the gear. The deformation is determined by the variations in the hardenability for a certain die quenching process. The relationship between hardenability, phase transformation and deformation needs to be studied to minimize deformation during the adjustment of the die quenching process parameters. In this paper, material properties for 22CrMoH steel are determined by the results of Jominy tests, dilatometry experiments and static mechanical property tests. The material models were built based on testing results under the consideration of hardenability variation. An finite element analysis model was developed to couple the phase transformation and deformation history of the complete carburizing and die quenching process for the spiral bevel gears. The final microstructures in the gear were bainite for low hardenability steel and a mixture of bainite and ferrite for high hardenability steel. The largest buckling deformation at the gear bottom surface is 0.375 mm at the outer circle for the low hardenability gear and 0.091 mm at the inner circle for the high hardenability gear.

Euthanasia, assisted dying and the right to die in Ghana: a socio-legal analysis.

PubMed

Owusu-Dapaa, Ernest

2013-12-01

There is unanimity among states to protect the continuation of life of the individual as a safeguard against their collective extinction. The right to life is accordingly guaranteed but its antithesis, the right to die is the subject of an unending debate. The controversy over the right to die is deepened by rapid advances in medicine, creating the capability for prolongation of life beyond the span which one's natural strength can endure. Ghana's supreme law explicitly guarantees the right to life but remains ambiguous on right to die, particularly euthanasia and assisted dying. Thus, some of the other rights, such as the right to dignity and not to be tortured, can creatively be exploited to justify some instances of euthanasia. Ghana's criminal code largely proscribes euthanasia. Notwithstanding, proscription of euthanasia and assisted dying by the law, in Ghana's empirical work undertaken in some of the communities in Ghana, suggests that euthanasia is quietly practisedin health facilities and private homes, especially in the rural areas. Contrary to the popular reasons assigned in the literature of the Western world, with respect to the practice or quest for legalization of euthanasia as being a necessity for providing relief from pain or hopeless quality of life, empirical data from social and anthropological studies conducted in Ghana reveal that poverty is the motivation for informal euthanasia practice in Ghana rather than genuine desire on part of patients to die or their relatives to see to their accelerated death. Apart from poverty, traditional cultural values of African societies consider non-natural death as a taboo and ignominy to the victim and his family. Thus, any move by the government to legalize euthanasia will need to be informed by widely held consultations and a possible referendum; otherwise the law may be just a mere transplant of Western models of legislation on euthanasia without reflecting the ethos of the African people.

Klamath River Basin Hydrologic Conditions Prior to the September 2002 Die-Off of Salmon and Steelhead

USGS Publications Warehouse

Lynch, Dennis D.; Risley, John C.

2003-05-27

This report characterizes streamflow and water temperature conditions during the period leading up to the die-off and compares them to historical conditions in the Klamath River. This report is not an exploration of the causative mechanism of the die-off; rather, it is intended to provide detailed documentation of these conditions to be used by those examining the cause(s) of the die-off and to provide information that can contribute to decisions about future water management in the Klamath Basin.

Roll-to-roll Slot-die Printed Polymer Solar Cell by Self-Assembly.

PubMed

Yang, Junyu; Lin, Yuanbao; Zheng, Wenhao; Liu, Alei; Cai, Wanzhu; Yu, Xiaomin; Zhang, Fengling; Liang, Quanbin; Wu, Hongbin; Qin, Donghuan; Hou, Lintao

2018-06-12

Extremely simplified one-step roll-to-roll slot-die printed flexible ITO-free polymer solar cells (PSCs) are demonstrated based on ternary blends of electron-donor polymer thieno [3,4-b]thiophene/benzodithiophene (PTB7), electron-acceptor fullerene [6,6]-phenyl-C71-butyric acid methyl ester (PC71BM) and electron extracting polymer poly [(9,9-bis(3'-(N,N-dimethylamino)propyl)-2,7-fluorene)-alt-2,7-(9,9-dioctylfluorene)] (PFN) at room temperature (RT) in ambient air. The flexible ITO-free PSC exhibits a comparable power conversion efficiency (PCE) with the device employing complicated two-step slot-die printing (5.29% vs 5.41%), which indicates that PFN molecules can migrate from the ternary nanocomposite towards Ag cathode via vertical self-assembly during the one-step slot-die printing process in air. To confirm the migration of PFN, the morphology and elemental analysis as well as charge transport of different active layers are investigated with in-situ transient film drying process, transmission electron microscopy, atomic force microscopy, contact angle and surface energy, X-ray photoelectron spectroscopy, scanning electron microscope, impedance spectroscopy, transient photovoltage and transient photocurrent as well as laser beam induced current. Moreover, the good air and mechanical stability of the flexible device with a decent PCE achieved in 1 cm2 PSCs at RT in air suggests the feasibility of energy-saving and time-saving one-step slot-die printing to large-scale roll-to-roll manufacture in the future.

Prolonging dying is the same as prolonging living--one more response to Long.

PubMed Central

Kuhse, H; Singer, P

1991-01-01

In earlier publications, we had argued that Paul Ramsey is inconsistent because he simultaneously asserts that (i) 'all our days and years are of equal worth' and (ii) 'that it is permissible to refrain from prolonging the lives of some dying patients'. Thomas Long has suggested that we have not shown that Paul Ramsey is inconsistent. Ramsey and we, he holds, start from incommensurable metaphysical views: for Ramsey, the dying process has religious significance--God is calling his servant home. While it is normally a good thing to keep a patient alive, it would, for Ramsey, show deafness to God's call to keep a dying patient alive. It is true we do not share Paul Ramsey's religious views. It is, however, not necessary to rely on any particular metaphysical views to refute Ramsey's position. For Ramsey's view to be internally consistent, Ramsey would have to be able to distinguish between dying and non-dying patients. We examine some of Ramsey's examples and show that his practical judgements do not allow us to draw this distinction. This means that, contra Long, we hold fast to our charge that Ramsey's view is inconsistent. PMID:1787522

Defining a Good Death (Successful Dying): Literature Review and a Call for Research and Public Dialogue

PubMed Central

Meier, Emily A.; Gallegos, Jarred V.; Montross-Thomas, Lori P.; Depp, Colin A.; Irwin, Scott A.; Jeste, Dilip V.

2016-01-01

There is little agreement about what constitutes good death or successful dying. The authors conducted a literature search for published, English-language, peer-reviewed reports of qualitative and quantitative studies that provided a definition of a good death. Stakeholders in these articles included patients, prebereaved and bereaved family members, and healthcare providers (HCPs). Definitions found were categorized into core themes and subthemes, and the frequency of each theme was determined by stakeholder (patients, family, HCPs) perspectives. Thirty-six studies met eligibility criteria, with 50% of patient perspective articles including individuals over age 60 years. We identified 11 core themes of good death: preferences for a specific dying process, pain-free status, religiosity/spiritualty, emotional well-being, life completion, treatment preferences, dignity, family, quality of life, relationship with HCP, and other. The top three themes across all stakeholder groups were preferences for dying process (94% of reports), pain-free status (81%), and emotional well-being (64%). However, some discrepancies among the respondent groups were noted in the core themes: Family perspectives included life completion (80%), quality of life (70%), dignity (70%), and presence of family (70%) more frequently than did patient perspectives regarding those items (35%–55% each). In contrast, religiosity/spirituality was reported somewhat more often in patient perspectives (65%) than in family perspectives (50%). Taking into account the limitations of the literature, further research is needed on the impact of divergent perspectives on end-of-life care. Dialogues among the stakeholders for each individual must occur to ensure a good death from the most critical viewpoint—the patient’s. PMID:26976293

Fast lichtschnell durch die Stadt: Visualisierung relativistischer Effekte

NASA Astrophysics Data System (ADS)

Kraus, Ute; Borchers, Marc P.

2005-03-01

Eine Computersimulation ermöglicht es uns, mit annähernd Lichtgeschwindigkeit durch die Tübinger Fußgängerzone zu fahren. Was wir dabei sehen, ist verblüffend: Die Häuser vor uns rücken umso weiter in die Ferne, je mehr wir beschleunigen; gleichzeitig erscheinen die Hauskanten in unserer Nähe immer stärker gekrümmt. Der Grund für diese merkwürdigen Bilder ist die so genannte Aberration: Ein und derselbe Lichtstrahl hat für den fahrenden Beobachter eine andere Richtung als für denjenigen, der am Straßenrand steht. Dieser Effekt ist im Alltag klein. Wenn wir aber in der Simulation fast lichtschnell durch die Tübinger Altstadt rasen, ist er dramatisch groß.

Assisted Dying in Canada.

PubMed

Schuklenk, Udo

This paper makes an affirmative ethical case in favour of the decriminalization of assisted dying in Canada. It then proceeds to defending the affirmative case against various slippery-slope arguments that are typically deployed by opponents of assisted dying. Finally, a recent case of questionable professional conduct by anti-euthanasia campaigners cum academics is flagged as a warning to all of us not to permit the quality of the professional debate to deteriorate unacceptably, despite the personal emotional investments involved on all sides of the debate.

Thermal Stress Analysis for Ceramics Stalk in the Low Pressure Die Casting Machine

NASA Astrophysics Data System (ADS)

Noda, Nao-Aki; Hendra, Nao-Aki; Takase, Yasushi; Li, Wenbin

Low pressure die casting (LPDC) is defined as a net shape casting technology in which the molten metal is injected at high speeds and pressure into a metallic die. The LPDC process is playing an increasingly important role in the foundry industry as a low-cost and high-efficiency precision forming technique. The LPDC process is that the permanent die and filling systems are placed over the furnace containing the molten alloy. The filling of the cavity is obtained by forcing the molten metal by means of a pressurized gas in order to rise into a ceramic tube, which connects the die to the furnace. The ceramics tube called stalk has high temperature resistance and high corrosion resistance. However, attention should be paid to the thermal stress when the stalk is dipped into the molten aluminum. It is important to develop the design of the stalk to reduce the risk of fracture because of low fracture toughness of ceramics. In this paper, therefore, the finite element method is applied to calculate the thermal stresses when the stalk is dipped into the crucible by varying the dipping speeds and dipping directions. It is found that the thermal stress can be reduced by dipping slowly if the stalk is dipped into the crucible vertically, while the thermal stress can be reduced by dipping fast if it is dipped horizontally.

Optimization of porthole die geometrical variables by Taguchi method

NASA Astrophysics Data System (ADS)

Gagliardi, F.; Ciancio, C.; Ambrogio, G.; Filice, L.

2017-10-01

Porthole die extrusion is commonly used to manufacture hollow profiles made of lightweight alloys for numerous industrial applications. The reliability of extruded parts is affected strongly by the quality of the longitudinal and transversal seam welds. According to that, the die geometry must be designed correctly and the process parameters must be selected properly to achieve the desired product quality. In this study, numerical 3D simulations have been created and run to investigate the role of various geometrical variables on punch load and maximum pressure inside the welding chamber. These are important outputs to take into account affecting, respectively, the necessary capacity of the extrusion press and the quality of the welding lines. The Taguchi technique has been used to reduce the number of the required numerical simulations necessary for considering the influence of twelve different geometric variables. Moreover, the Analysis of variance (ANOVA) has been implemented to individually analyze the effect of each input parameter on the two responses. Then, the methodology has been utilized to determine the optimal process configuration individually optimizing the two investigated process outputs. Finally, the responses of the optimized parameters have been verified through finite element simulations approximating the predicted value closely. This study shows the feasibility of the Taguchi technique for predicting performance, optimization and therefore for improving the design of a porthole extrusion process.

A clinical perspective on dying

PubMed Central

Janes, Robert G.

1972-01-01

There is continuing need for dissemination of already available, clinically useful knowledge concerning the psychological needs of the seriously ill and dying. Against the changing social context of dying, some of our erroneous assumptions about these patients are explored and the genuine fears and personal needs are discussed. The implications of this knowledge for medical education are recognized. PMID:5074753

A framework for development of an intelligent system for design and manufacturing of stamping dies

NASA Astrophysics Data System (ADS)

Hussein, H. M. A.; Kumar, S.

2014-07-01

An integration of computer aided design (CAD), computer aided process planning (CAPP) and computer aided manufacturing (CAM) is required for development of an intelligent system to design and manufacture stamping dies in sheet metal industries. In this paper, a framework for development of an intelligent system for design and manufacturing of stamping dies is proposed. In the proposed framework, the intelligent system is structured in form of various expert system modules for different activities of design and manufacturing of dies. All system modules are integrated with each other. The proposed system takes its input in form of a CAD file of sheet metal part, and then system modules automate all tasks related to design and manufacturing of stamping dies. Modules are coded using Visual Basic (VB) and developed on the platform of AutoCAD software.

Impact of Simulation Technology on Die and Stamping Business

NASA Astrophysics Data System (ADS)

Stevens, Mark W.

2005-08-01

Over the last ten years, we have seen an explosion in the use of simulation-based techniques to improve the engineering, construction, and operation of GM production tools. The impact has been as profound as the overall switch to CAD/CAM from the old manual design and construction methods. The changeover to N/C machining from duplicating milling machines brought advances in accuracy and speed to our construction activity. It also brought significant reductions in fitting sculptured surfaces. Changing over to CAD design brought similar advances in accuracy, and today's use of solid modeling has enhanced that accuracy gain while finally leading to the reduction in lead time and cost through the development of parametric techniques. Elimination of paper drawings for die design, along with the process of blueprinting and distribution, provided the savings required to install high capacity computer servers, high-speed data transmission lines and integrated networks. These historic changes in the application of CAE technology in manufacturing engineering paved the way for the implementation of simulation to all aspects of our business. The benefits are being realized now, and the future holds even greater promise as the simulation techniques mature and expand. Every new line of dies is verified prior to casting for interference free operation. Sheet metal forming simulation validates the material flow, eliminating the high costs of physical experimentation dependent on trial and error methods of the past. Integrated forming simulation and die structural analysis and optimization has led to a reduction in die size and weight on the order of 30% or more. The latest techniques in factory simulation enable analysis of automated press lines, including all stamping operations with corresponding automation. This leads to manufacturing lines capable of running at higher levels of throughput, with actual results providing the capability of two or more additional strokes per

The Dying Role: Its Relevance to Improved Patient Care.

PubMed

Noyes, Russell; Clancy, John

2016-01-01

SOCIETY is failing to meet the obligation it has to its dying members. Persons with terminal illnesses suffer isolation and neglect in hospitals, receive overzealous treatment by physicians, and are kept in ignorance of their situation by families and medical personnel. Evidence for these statements has come from observers of the medical care system and from dying patients themselves (Kübler-Ross, 1969; Reynolds and Kalish, 1974; Sudnow, 1967). In the nineteenth century it was common for persons to die in the familiar environs of their homes, surrounded by grieving families from whom they parted in a meaningful manner (Blauner, 1966). Dying persons of today no longer fill a well-defined social role. Instead, the distinction between the roles of sick and dying persons has been lost and, in the resulting confusion, the care of dying people has suffered. The purpose of this article is to clarify the distinction between the dying and sick roles, identify the signs of existing role confusion, suggest ways in which this confusion may be corrected, and show how reestablishment of the dying role can result in improved care of dying people. The important part physicians play in defining sick and dying roles will be emphasized.

'Bridging worlds': meeting the emotional needs of dying patients.

PubMed

Law, Rollanda

2009-12-01

This paper is a report of a study to develop a grounded theory to explain how district nurses meet the emotional needs of dying patients in the community. There has been a policy commitment internationally to improve community services and enable people with terminal illnesses to die in their own homes. This increasing trend towards home deaths in the United Kingdom (UK) makes more demand on district nurses to provide emotional support for dying patients. A 'classic' grounded theory study was conducted in the UK between 2002 and 2005. Unstructured observations and semi-structured interviews were conducted with a purposive sample of nine district nurses, nine patients and four family carers. A further theoretical sample of five books of authors' accounts of their dying experiences and three district nurses who were advanced practitioners were selected. Five categories were identified in the data: 'outside world', 'dying world', 'entering dying world', 'maintaining connections' and the core category 'bridging worlds'. The theory of 'bridging worlds' indicated that dying patients experienced 'dying world' and 'outside world'. District nurses met dying patients' emotional needs by acting as a bridge between their two worlds, encouraging them to maintain connections with the outside world so that they did not become isolated in their dying world. District nurses should ensure that they meet both the physical and emotional needs of dying patients. Nursing education and literature need to concentrate on raising awareness of nurses' role in providing emotional support.

Modelling the Cast Component Weight in Hot Chamber Die Casting using Combined Taguchi and Buckingham's π Approach

NASA Astrophysics Data System (ADS)

Singh, Rupinder

2018-02-01

Hot chamber (HC) die casting process is one of the most widely used commercial processes for the casting of low temperature metals and alloys. This process gives near-net shape product with high dimensional accuracy. However in actual field environment the best settings of input parameters is often conflicting as the shape and size of the casting changes and one have to trade off among various output parameters like hardness, dimensional accuracy, casting defects, microstructure etc. So for online inspection of the cast components properties (without affecting the production line) the weight measurement has been established as one of the cost effective method (as the difference in weight of sound and unsound casting reflects the possible casting defects) in field environment. In the present work at first stage the effect of three input process parameters (namely: pressure at 2nd phase in HC die casting; metal pouring temperature and die opening time) has been studied for optimizing the cast component weight `W' as output parameter in form of macro model based upon Taguchi L9 OA. After this Buckingham's π approach has been applied on Taguchi based macro model for the development of micro model. This study highlights the Taguchi-Buckingham based combined approach as a case study (for conversion of macro model into micro model) by identification of optimum levels of input parameters (based on Taguchi approach) and development of mathematical model (based on Buckingham's π approach). Finally developed mathematical model can be used for predicting W in HC die casting process with more flexibility. The results of study highlights second degree polynomial equation for predicting cast component weight in HC die casting and suggest that pressure at 2nd stage is one of the most contributing factors for controlling the casting defect/weight of casting.

Acting to let someone die.

PubMed

McGee, Andrew

2015-02-01

This paper examines the recent prominent view in medical ethics that withdrawing life-sustaining treatment (LST) is an act of killing. I trace this view to the rejection of the traditional claim that withdrawing LST is an omission rather than an act. Although that traditional claim is not as problematic as this recent prominent view suggests, my main claim is that even if we accepted that withdrawing LST should be classified as an act rather than as an omission, it could still be classified as letting die rather than killing. Even though omissions are contrasted with acts, letting die need not be, for one can let die by means of acts. The remainder of the paper is devoted to establishing this claim and addresses certain objections to it. © 2013 John Wiley & Sons Ltd.

Computer aided system for parametric design of combination die

NASA Astrophysics Data System (ADS)

Naranje, Vishal G.; Hussein, H. M. A.; Kumar, S.

2017-09-01

In this paper, a computer aided system for parametric design of combination dies is presented. The system is developed using knowledge based system technique of artificial intelligence. The system is capable to design combination dies for production of sheet metal parts having punching and cupping operations. The system is coded in Visual Basic and interfaced with AutoCAD software. The low cost of the proposed system will help die designers of small and medium scale sheet metal industries for design of combination dies for similar type of products. The proposed system is capable to reduce design time and efforts of die designers for design of combination dies.

Finite element modelling of chain-die forming for ultra-high strength steel

NASA Astrophysics Data System (ADS)

Majji, Raju; Xiang, Yang; Ding, Scott; Yang, Chunhui

2017-10-01

There has been a high demand for weight reduction in automotive vehicles while maintaining passenger safety. A potential steel material to achieve this is Ultra High Strength Steel (UHSS). As a high strength material, it is difficult to be formed with desired profiles using traditional sheet metal forming processes such as Cold Roll Forming. To overcome this problem, a potentially alternative solution is Chain-die Forming (CDF), recently developed. The basic principal of the CDF is to fully combine roll forming and bending processes. The main advantage of this process is the elongated deformation length that significantly increases effective roll radius. This study focuses on identifying issues with the CDF by using CAD modelling, Motion Analysis and Finite Element Analysis (FEA) to devise solutions and construct a more reliable process in an optimal design sense. Some attempts on finite element modelling and simulation of the CDF were conducted using relatively simple models in literature and the research was still not sufficient enough for optimal design of a typical CDF for UHSS. Therefore two numerical models of Chain-die Forming process are developed in this study, including a) one having a set of rolls similar to roll forming but with a large radius, i.e., 20 meters; and b) the other one with dies and punch segments similar to a typical CDF machine. As a case study, to form a 60° channel with single pass was conducted using these two devised models for a comparison. The obtained numerical results clearly show the CDF could generate less residual stress, low strain and small springback of a single pass for the 60° UHSS channel. The design analysis procedure proposed in this study could greatly help the mechanical designers to devise a cost-effective and reliable CDF process for forming UHSS.

End-of-life care policy: An integrated care plan for the dying

PubMed Central

Myatra, Sheila Nainan; Salins, Naveen; Iyer, Shivakumar; Macaden, Stanley C.; Divatia, Jigeeshu V.; Muckaden, Maryann; Kulkarni, Priyadarshini; Simha, Srinagesh; Mani, Raj Kumar

2014-01-01

Purpose: The purpose was to develop an end-of-life care (EOLC) policy for patients who are dying with an advanced life limiting illness and to develop practical procedural guidelines for limiting inappropriate therapeutic medical interventions and improve the quality of care of the dying within an ethical framework and through a professional and family/patient consensus process. Evidence: The Indian Society of Critical Care Medicine (ISCCM) published its first guidelines on EOLC in 2005 [1] which was later revised in 2012.[2] Since these publications, there has been an exponential increase in empirical information and discussion on the subject. The literature reviewed observational studies, surveys, randomized controlled studies, as well as guidelines and recommendations, for education and quality improvement published across the world. The search terms were: EOLC; do not resuscitate directives; withdrawal and withholding; intensive care; terminal care; medical futility; ethical issues; palliative care; EOLC in India; cultural variations. Indian Association of Palliative Care (IAPC) also recently published its consensus position statement on EOLC policy for the dying.[3] Method: An expert committee of members of the ISCCM and IAPC was formed to make a joint EOLC policy for the dying patients. Proposals from the chair were discussed, debated, and recommendations were formulated through a consensus process. The members extensively reviewed national and international established ethical principles and current procedural practices. This joint EOLC policy has incorporated the sociocultural, ethical, and legal perspectives, while taking into account the needs and situation unique to India. PMID:25249748

REFRACTORY DIE FOR EXTRUDING URANIUM

DOEpatents

Creutz, E.C.

1959-08-11

A die is presented for the extrusion of metals, said die being formed of a refractory complex oxide having the composition M/sub n/O/sub m/R/sub x/O/sub y/ where M is magnesium, zinc, manganese, or iron, R is aluminum, chromic chromium, ferric iron, or manganic manganese, and m, n, x, and y are whole numbers. Specific examples are spinel, magnesium aluminate, magnetite, magnesioferrite, chromite, and franklinite.

Care of the dying: how do we replace the Liverpool Care Pathway?

PubMed

Davis, Charles; Tomas, Jon

2014-12-01

Death is an inescapable certainty of life. Variability in care for dying persons, however, is present. The Liverpool Care Pathway (LCP) sought to guide care for the last days of life but was phased out after intense scrutiny. A governmental report and rapid review of evidence were considered alongside mass and social media reporting. An evidence review of end-of-life care was undertaken. Any person's death is inherently challenging. Much consideration must be given to holistic needs when approaching death. Communication skills may be lacking for professional and patient alike. The LCP became flawed in use rather than intention or principle. Seeming financial gains from death were concerning to all. We have responsibility for making choices prospectively in order for them to influence our care when we are dying. Normalization of death is key on both micro- and macro communication levels. Perceptions of relevant terminology; review of the definition of dying; improved recognition of the dying process and measuring the impact of communication skills training. © The Author 2014. Published by Oxford University Press. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Development and evaluation of die materials for use in the growth of silicon ribbons by the inverted ribbon growth process, task 2. LSSA project

NASA Technical Reports Server (NTRS)

Duffy, M. T.; Berkman, S.; Moss, H. S.; Cullen, G. W.

1978-01-01

The results of emission spectroscopic analysis indicate that molten silicon can remain in contact with hot-pressed Si3N4 (99.2 percent theoretical density) for prolonged periods without attaining the impurity content level of the nitride. Although MgO was used as binder, Mg was not found present in the silicon sessile drop in quantities much above the level initially present in the silicon source material. Preliminary experiments with EFG-type dies coated with CVD Si3N4 or CVD SiOxNy indicate that capillary rise does not occur readily in these dies. The same was found to be true of hot-pressed and reaction-sintered Si3N4 obtained commercially. However, when dies were formed by depositing CVD layers on shaped silicon slabs, a column of molten silicon was maintained in each CVD die while being heated in contact with a crucible of molten silicon. Preliminary wetting of dies appears necessary for EFG growth. Several ribbon growth experiments were performed from V-shaped dies.

[Reasons for deciding to die in hospital or at home. The vision of professionals].

PubMed

Lima-Rodríguez, Joaquín Salvador; Asensio-Pérez, Mª de Los Reyes; Palomo-Lara, Juan Carlos; Ramírez-López, Encarnación Bella; Lima-Serrano, Marta

2018-05-21

To discover the reasons for deciding to die in hospital or at home, from the perspective of professionals involved. Qualitative phenomenological study. Intentional sample. Four multidisciplinary focus groups were held, two in hospitals and two in primary care centres in Seville (Spain). Twenty-nine professionals with at least two years experience in the care of people with a terminal disease participated, following the theoretical saturation of information criterion. Responses from the first script were gathered in three core categories: patient and the family, professionals and care process. Patients are generally not asked about their preferences as to where they wish to die, and if their family is not aware of their preference, it is not possible to carry out advanced planning of care. Families tend to choose the hospital because of the possibility of monitoring and resources in primary care. Professionals are trained in how to approach death, but they do not feel sufficiently prepared and focus on the clinical and administrative issues. The care process favours oncology patients because it is easier to identify their illness as terminal. Resources are not equal and interlevel communication needs to be improved. The family's involvement in the process is not facilitated, which impedes their decision-making. Advance care planning and use of the advance directive should be promoted, as well as, interlevel communication and coordination, supply resources, especially in primary care, and professionals should receive training on how to approach death.. The patient's family should be involved in the care process and provided the necessary support. Copyright © 2018 SESPAS. Publicado por Elsevier España, S.L.U. All rights reserved.

A Contingency Framework for Listening to the Dying

ERIC Educational Resources Information Center

Vora, Erika; Vora, Ariana

2008-01-01

Listening to the dying poses special challenges. This paper proposes a contingency framework for describing and assessing various circumstances when listening to the dying. It identifies current approaches to listening, applies the contingency framework toward effectively listening to the dying, and proposes a new type of listening called…

Self-determination, the right to die, and culture: a literature review.

PubMed

McCormick, Andrew J

2011-04-01

Self-determination is a primary ethical principle underlying social work practice in health care settings. Since the 1970s, a right-to-die movement that shares the social work commitment to self-determination has grown and influences end-of-life care decisions. However, the role of culture is notably absent in discussions of the right to die. A literature review was conducted to explore self-determination and the role of culture in the context of the history of the right-to-die movement. A total of 54 articles met the criteria for inclusion in the review. Of the total, 21 related to self-determination, and 12 related to ethnicity and culture at the end of life. A history based on the review of the right-to-die movement is presented. The review found that social workers support passively hastening death and that views of self-determination are affected by both law and culture. In response, social workers will face three tasks: (1) becoming more public in their support for client self-determination as an important standard in end-of-life care, (2) being more explicit in support of diverse cultural traditions in end-of-life decision making, and (3) expanding their traditional educational and bridging roles between families and medical personnel.

The Simulation of Magnesium Wheel Low Pressure Die Casting Based on PAM-CAST™

NASA Astrophysics Data System (ADS)

Peng, Yinghong; Wang, Yingchun; Li, Dayong; Zeng, Xiaoqin

2004-06-01

Magnesium is the lightest metal commonly used in engineering, with various excellent characteristics such as high strength and electromagnetic interference shielding capability. Particularly, the usage of magnesium in automotive industry can meet better the need to reduce fuel consumption and CO2 emissions. Nowadays, most current magnesium components in automobiles are made by die casting. In this paper, commercial software for die casting, PAM-CAST™, was utilized to simulate the low pressure die casting process of magnesium wheel. Through calculating temperature field and velocity field during filling and solidification stages, the evolution of temperature distribution and liquid fraction was analyzed. Then, the potential defects including the gas entrapments in the middle of the spokes, shrinkages between the rim and the spokes were forecasted. The analytical results revealed that the mold geometry and die casting parameters should be improved in order to get the sound magnesium wheel. The reasons leading to these defects were also analyzed and the solutions to eliminate them were put forward. Furthermore, through reducing the pouring velocity, the air gas entrapments and partial shrinkages were eliminated effectively.

Ageless Aluminum-Cerium-Based Alloys in High-Volume Die Casting for Improved Energy Efficiency

NASA Astrophysics Data System (ADS)

Stromme, Eric T.; Henderson, Hunter B.; Sims, Zachary C.; Kesler, Michael S.; Weiss, David; Ott, Ryan T.; Meng, Fanqiang; Kassoumeh, Sam; Evangelista, James; Begley, Gerald; Rios, Orlando

2018-06-01

Strong chemical reactions between Al and Ce lead to the formation of intermetallics with exceptional thermal stability. The rapid formation of intermetallics directly from the liquid phase during solidification of Al-Ce alloys leads to an ultrafine microconstituent structure that effectively strengthens as-cast alloys without further microstructural optimization via thermal processing. Die casting is a high-volume manufacturing technology that accounts for greater than 40% of all cast Al products, whereas Ce is highly overproduced as a waste product of other rare earth element (REE) mining. Reducing heat treatments would stimulate significant improvements in manufacturing energy efficiency, exceeding (megatonnes/year) per large-scale heat-treatment line. In this study, multiple compositions were evaluated with wedge mold castings to test the sensitivity of alloys to the variable solidification rate inherent in high-pressure die casting. Once a suitable composition was determined, it was successfully demonstrated at 800 lbs/h in a 600-ton die caster, after which the as-die cast parts performed similarly to ubiquitous A380 in the same geometry without requiring heat treatment. This work demonstrates the compatibility of Al REE alloys with high-volume die-casting applications with minimal heat treatments.

Ageless Aluminum-Cerium-Based Alloys in High-Volume Die Casting for Improved Energy Efficiency

NASA Astrophysics Data System (ADS)

Stromme, Eric T.; Henderson, Hunter B.; Sims, Zachary C.; Kesler, Michael S.; Weiss, David; Ott, Ryan T.; Meng, Fanqiang; Kassoumeh, Sam; Evangelista, James; Begley, Gerald; Rios, Orlando

2018-04-01

Strong chemical reactions between Al and Ce lead to the formation of intermetallics with exceptional thermal stability. The rapid formation of intermetallics directly from the liquid phase during solidification of Al-Ce alloys leads to an ultrafine microconstituent structure that effectively strengthens as-cast alloys without further microstructural optimization via thermal processing. Die casting is a high-volume manufacturing technology that accounts for greater than 40% of all cast Al products, whereas Ce is highly overproduced as a waste product of other rare earth element (REE) mining. Reducing heat treatments would stimulate significant improvements in manufacturing energy efficiency, exceeding (megatonnes/year) per large-scale heat-treatment line. In this study, multiple compositions were evaluated with wedge mold castings to test the sensitivity of alloys to the variable solidification rate inherent in high-pressure die casting. Once a suitable composition was determined, it was successfully demonstrated at 800 lbs/h in a 600-ton die caster, after which the as-die cast parts performed similarly to ubiquitous A380 in the same geometry without requiring heat treatment. This work demonstrates the compatibility of Al REE alloys with high-volume die-casting applications with minimal heat treatments.

Quality of Dying in Nursing Home Residents Dying with Dementia: Does Advanced Care Planning Matter? A Nationwide Postmortem Study

PubMed Central

Vandervoort, An; Houttekier, Dirk; Vander Stichele, Robert; van der Steen, Jenny T.; Van den Block, Lieve

2014-01-01

Background Advance care planning is considered a central component of good quality palliative care and especially relevant for people who lose the capacity to make decisions at the end of life, which is the case for many nursing home residents with dementia. We set out to investigate to what extent (1) advance care planning in the form of written advance patient directives and verbal communication with patient and/or relatives about future care and (2) the existence of written advance general practitioner orders are related to the quality of dying of nursing home residents with dementia. Methods Cross-sectional study of deaths (2010) using random cluster-sampling. Representative sample of nursing homes in Flanders, Belgium. Deaths of residents with dementia in a three-month period were reported; for each the nurse most involved in care, GP and closest relative completed structured questionnaires. Findings We identified 101 deaths of residents with dementia in 69 nursing homes (58% response rate). A written advance patient directive was present for 17.5%, GP-orders for 56.7%. Controlling for socio-demographic/clinical characteristics in multivariate regression analyses, chances of having a higher mean rating of emotional well-being (less fear and anxiety) on the Comfort Assessment in Dying with Dementia scale were three times higher with a written advance patient directive and more specifically when having a do-not-resuscitate order (AOR 3.45; CI,1.1–11) than for those without either (AOR 2.99; CI,1.1–8.3). We found no association between verbal communication or having a GP order and quality of dying. Conclusion For nursing home residents with dementia there is a strong association between having a written advance directive and quality of dying. Where wishes are written, relatives report lower levels of emotional distress at the end of life. These results underpin the importance of advance care planning for people with dementia and beginning this process as

Development of a 3D Filling Model of Low-Pressure Die-Cast Aluminum Alloy Wheels

NASA Astrophysics Data System (ADS)

Duan, Jianglan; Maijer, Daan; Cockcroft, Steve; Reilly, Carl

2013-12-01

A two-phase computational fluid dynamics model of the low-pressure die-cast process for the production of A356 aluminum alloy wheels has been developed to predict the flow conditions during die filling. The filling model represents a 36-deg section of a production wheel, and was developed within the commercial finite-volume package, ANSYS CFX, assuming isothermal conditions. To fully understand the behavior of the free surface, a novel technique was developed to approximate the vent resistances as they impact on the development of a backpressure within the die cavity. The filling model was first validated against experimental data, and then was used to investigate the effects of venting conditions and pressure curves during die filling. It was found that vent resistance and vent location strongly affected die filling time, free surface topography, and air entrainment for a given pressure fill-curve. With regard to the pressure curve, the model revealed a strong relation between the pressure curve and the flow behavior in the hub, which is an area prone to defect formation.

Numerical simulation on chain-die forming of an AHSS top-hat section

NASA Astrophysics Data System (ADS)

Majji, Raju; Xiang, Yang; Ding, Scott; Yang, Chunhui

2018-05-01

The applications of Advanced High-Strength Steels (AHSS) in the automotive industry are rapidly increasing due to a demand for a lightweight material that significantly reduces fuel consumption without compromising passenger safety. Automotive industries and material suppliers are expected by consumers to deliver reliable and affordable products, thus stimulating these manufacturers to research solutions to meet these customer requirements. The primary advantage of AHSS is its extremely high strength to weight ratio, an ideal material for the automotive industry. However, its low ductility is a major disadvantage, in particular, when using traditional cold forming processes such as roll forming and deep drawing process to form profiles. Consequently, AHSS parts frequently fail to form. Thereby, in order to improve quality and reliability on manufacturing AHSS products, a recently-developed incremental cold sheet metal forming technology called Chain-die Forming (CDF) is recognised as a potential solution to the forming process of AHSS. The typical CDF process is a combination of bending and roll forming processes which is equivalent to a roll with a large deforming radius, and incrementally forms the desired shape with split die and segments. This study focuses on manufacturing an AHSS top-hat section with minimum passes without geometrical or surface defects by using finite element modelling and simulations. The developed numerical simulation is employed to investigate the influences on the main control parameter of the CDF process while forming AHSS products and further develop new die-punch sets of compensation design via a numerical optimal process. In addition, the study focuses on the tool design to compensate spring-back and reduce friction between tooling and sheet-metal. This reduces the number of passes, thereby improving productivity and reducing energy consumption and material waste. This numerical study reveals that CDF forms AHSS products of complex

Die nuklearen Anlagen von Hanford (1943-1987) Eine Fallstudie über die Schnittstellen von Physik, Biologie und die US-amerikanische Gesellschaft zur Zeit des Kalten Krieges

NASA Astrophysics Data System (ADS)

Macuglia, Daniele

Die Geschichte des Kalten Krieges eröffnet viele Möglichkeiten, sich näher mit den Schnittstellen von Physik und Biologie während des 20. Jahrhunderts zu befassen. Nicht nur das Unglück in Tschernobyl aus dem Jahr 1986, auch das Beispiel der nuklearen Anlagen in Hanford in den Vereinigten Staaten zeigt die biologischen Folgen von nuklearer Physik.

Chip-to-chip interconnects based on 3D stacking of optoelectrical dies on Si

NASA Astrophysics Data System (ADS)

Duan, P.; Raz, O.; Smalbrugge, B. E.; Duis, J.; Dorren, H. J. S.

2012-01-01

We demonstrate a new approach to increase the optical interconnection bandwidth density by stacking the opto-electrical dies directly on the CMOS driver. The suggested implementation is aiming to provide a wafer scale process which will make the use of wire bonding redundant and will allow for impedance matched metallic wiring between the electronic driving circuit and its opto-electronic counter part. We suggest the use of a thick photoresist ramp between CMOS driver and opto-electrical dies surface as the bridge for supporting co-plannar waveguides (CPW) electrically plated with lithographic accuracy. In this way all three dimensions of the interconnecting metal layer, width, length and thickness can be completely controlled. In this 1st demonstration all processing is done on commercially available devices and products, and is compatible with CMOS processing technology. To test the applicability of CPW instead of wire bonds for interconnecting the CMOS circuit and opto-electronic chips, we have made test samples and tested their performance at speeds up to 10 Gbps. In this demonstration, a silicon substrate was used on which we evaporated gold co-planar waveguides (CPW) to mimic a wire on the driver. An optical link consisting of a VCSEL chip and a photodiode chip has been assembled and fully characterized using optical coupling into and out of a multimode fiber (MMF). A 10 Gb/s 27-1 NRZ PRBS signal transmitted from one chip to another chip was detected error free. A 4 dB receiver sensitivity penalty is measured for the integrated device compared to a commercial link.

Case study of lean manufacturing application in a die casting manufacturing company

NASA Astrophysics Data System (ADS)

Ching, Ng Tan; Hoe, Clarence Chan Kok; Hong, Tang Sai; Ghobakhloo, Morteza; Pin, Chen Kah

2015-05-01

The case study of lean manufacturing aims to study the application of lean manufacturing in a die casting manufacturing company located in Pulau Penang, Malaysia. This case study describes mainly about the important concepts and applications of lean manufacturing which could gradually help the company in increasing the profit by studying and analyzing their current manufacturing process and company culture. Many approaches of lean manufacturing are studied in this project which includes: 5S housekeeping, Kaizen, and Takt Time. Besides, the lean tools mentioned, quality tool such as the House of Quality is being used as an analysis tool to continuously improve the product quality. In short, the existing lean culture in the company is studied and analyzed, with recommendations written at the end of this paper.

Dying Star Shrouded by a Blanket of Hailstones Forms the Bug Nebula

NASA Image and Video Library

2017-12-08

Release Date: May 3, 2004 A Dying Star Shrouded by a Blanket of Hailstones Forms the Bug Nebula (NGC 6302) The Bug Nebula, NGC 6302, is one of the brightest and most extreme planetary nebulae known. The fiery, dying star at its center is shrouded by a blanket of icy hailstones. This NASA Hubble Wide Field Plantery Camera 2 image shows impressive walls of compressed gas, laced with trailing strands and bubbling outflows. Object Names: NGC 6302, Bug Nebula Image Type: Astronomical Credit: NASA, ESA and A.Zijlstra (UMIST, Manchester, UK) To learn more about this image go to: hubblesite.org/gallery/album/nebula/pr2004046a/ NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

A simplified simulation model for a HPDC die with conformal cooling channels

NASA Astrophysics Data System (ADS)

Frings, Markus; Behr, Marek; Elgeti, Stefanie

2017-10-01

In general, the cooling phase of the high-pressure die casting process is based on complex physical phenomena: so-lidification of molten material; heat exchange between cast part, die and cooling fluid; turbulent flow inside the cooling channels that needs to be considered when computing the heat flux; interdependency of properties and temperature of the cooling liquid. Intuitively understanding and analyzing all of these effects when designing HPDC dies is not feasible. A remedy that has become available is numerical design, based for example on shape optimization methods. However, current computing power is not sufficient to perform optimization while at the same time fully resolving all physical phenomena. But since in HPDC suitable objective functions very often lead to integral values, e.g., average die temperature, this paper identifies possible simplifications in the modeling of the cooling phase. As a consequence, the computational effort is reduced to an acceptable level. A further aspect that arises in the context of shape optimization is the evaluation of shape gradients. The challenge here is to allow for large shape deformations without remeshing. In our approach, the cooling channels are described by their center lines. The flow profile of the cooling fluid is then estimated based on experimental data found in literature for turbulent pipe flows. In combination, the heat flux throughout cavity, die, and cooling channel can be described by one single advection-diffusion equation on a fixed mesh. The parameters in the equation are adjusted based on the position of cavity and cooling channel. Both results contribute towards a computationally efficient, yet accurate method, which can be employed within the frame of shape optimization of cooling channels in HPDC dies.

Optimization of Processing Parameters in ECM of Die Tool Steel Using Nanofluid by Multiobjective Genetic Algorithm.

PubMed

Sathiyamoorthy, V; Sekar, T; Elango, N

2015-01-01

Formation of spikes prevents achievement of the better material removal rate (MRR) and surface finish while using plain NaNO3 aqueous electrolyte in electrochemical machining (ECM) of die tool steel. Hence this research work attempts to minimize the formation of spikes in the selected workpiece of high carbon high chromium die tool steel using copper nanoparticles suspended in NaNO3 aqueous electrolyte, that is, nanofluid. The selected influencing parameters are applied voltage and electrolyte discharge rate with three levels and tool feed rate with four levels. Thirty-six experiments were designed using Design Expert 7.0 software and optimization was done using multiobjective genetic algorithm (MOGA). This tool identified the best possible combination for achieving the better MRR and surface roughness. The results reveal that voltage of 18 V, tool feed rate of 0.54 mm/min, and nanofluid discharge rate of 12 lit/min would be the optimum values in ECM of HCHCr die tool steel. For checking the optimality obtained from the MOGA in MATLAB software, the maximum MRR of 375.78277 mm(3)/min and respective surface roughness Ra of 2.339779 μm were predicted at applied voltage of 17.688986 V, tool feed rate of 0.5399705 mm/min, and nanofluid discharge rate of 11.998816 lit/min. Confirmatory tests showed that the actual performance at the optimum conditions was 361.214 mm(3)/min and 2.41 μm; the deviation from the predicted performance is less than 4% which proves the composite desirability of the developed models.

Diagnostic histological findings in Yosemite toads (Bufo canorus) from die-off in the 1970s

USGS Publications Warehouse

Green, D.E.; Sherman, C.K.

2001-01-01

Twelve adult and 25 larval Yosemite toad (Bufo canorus) specimens from the eastern Sierra Nevada of California were examined histologically for evidence of infectious, toxicological, and degenerative diseases. The preserved toads were selected from 21 that had been salvaged or collected during a die-off in 1976-1979 that immediately preceded a population decline. Causes of death of four toads were determined histologically; clinical signs and field observations suggested causes of death of three more. Four toads died of infectious diseases, including chytridiomycosis of the skin (N = 1), bacillary septicemia (N = 2), and combined chytridiomycosis and bacterial septicemia (N = 1). Infections by a funguslike organism (Dermosporidium penneri), renal myxozoa (Leptotheca ohlmacheri), larval Rhabdias, various gastrointestinal nematodes, urinary bladder flukes, and lung flukes were detected in five specimens. No evidence of degenerative diseases, virus infections, or intoxications was found. The variety of lethal diseases and our inability to determine the causes of death of five specimens suggests that one or more histologically undetectable diseases or intoxications may have also contributed to the deaths and population decline.

Shifting hospital-hospice boundaries: historical perspectives on the institutional care of the dying.

PubMed

Risse, Guenter B; Balboni, Michael J

2013-06-01

Social forces have continually framed how hospitals perceive their role in care of the dying. Hospitals were originally conceived as places of hospitality and spiritual care, but by the 18th century illness was an opponent, conquered through science. Medicalization transformed hospitals to places of physical cure and scientific prowess. Death was an institutional liability. Equipped with new technologies, increased public demand, and the establishment of Medicare in 1965, modern hospitals became the most likely place for Americans to die--increasing after the 1940s and spiking in the 1990s. Medicare's 1983 hospice benefit began to reverse this trend. Palliative care has more recently proliferated, suggesting an institutional shift of alignment with traditional functions of care toward those facing death.

Ars Moriendi; the art of dying well - new insights into the molecular pathways of necroptotic cell death.

PubMed

Murphy, James M; Silke, John

2014-02-01

When our time comes to die most people would probably opt for a quick, peaceful and painless exit. But the manner and timing are rarely under our direct control. Hence the Ars moriendi, literally, "The Art of Dying", two texts written in Latin around the 15th century that offered advice on how to die well according to the Christian ideals of the time. In contrast, for individual cells, the death process is frequently under their control and several signaling pathways that cause cell death, including apoptosis, pyroptosis and necroptosis, have been described. Furthermore the manner in which cells die can have good or bad consequences for the organism. In this review we will discuss how cells die via the necroptotic signaling pathway, with emphasis on recent structural work and place this work in a biological context by discussing relevant studies with knock-out animals.

25 CFR 304.5 - Dies to identify tribe.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 25 Indians 2 2014-04-01 2014-04-01 false Dies to identify tribe. 304.5 Section 304.5 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR NAVAJO, PUEBLO, AND HOPI SILVER, USE OF GOVERNMENT MARK § 304.5 Dies to identify tribe. Dies are marked with name of tribe. A Navajo stamp will be...

25 CFR 304.5 - Dies to identify tribe.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 25 Indians 2 2011-04-01 2011-04-01 false Dies to identify tribe. 304.5 Section 304.5 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR NAVAJO, PUEBLO, AND HOPI SILVER, USE OF GOVERNMENT MARK § 304.5 Dies to identify tribe. Dies are marked with name of tribe. A Navajo stamp will be...

25 CFR 304.5 - Dies to identify tribe.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 25 Indians 2 2012-04-01 2012-04-01 false Dies to identify tribe. 304.5 Section 304.5 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR NAVAJO, PUEBLO, AND HOPI SILVER, USE OF GOVERNMENT MARK § 304.5 Dies to identify tribe. Dies are marked with name of tribe. A Navajo stamp will be...

25 CFR 304.5 - Dies to identify tribe.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 25 Indians 2 2013-04-01 2013-04-01 false Dies to identify tribe. 304.5 Section 304.5 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR NAVAJO, PUEBLO, AND HOPI SILVER, USE OF GOVERNMENT MARK § 304.5 Dies to identify tribe. Dies are marked with name of tribe. A Navajo stamp will be...

Negotiated dying: a grounded theory of how nurses shape withdrawal of treatment in hospital critical care units.

PubMed

Long-Sutehall, Tracy; Willis, Helen; Palmer, Rachel; Ugboma, Debra; Addington-Hall, Julia; Coombs, Maureen

2011-12-01

The process of withdrawal of treatment in critical care environments has created ethical and moral dilemmas in relation to end of life care in the UK and elsewhere. Common within this discourse is the differing demands made on health professionals as they strive to provide care for the dying patient and family members. Despite reports that withdrawal of treatment is a source of tension between those nurses and doctors involved in the process, the role of the nurse in facilitating withdrawal of treatment has received relatively little attention. To illustrate how differing dying trajectories impact on decision-making underpinning withdrawal of treatment processes, and what nurses do to shape withdrawal of treatment. Qualitative methods of enquiry using clinical vignettes and applying Charmaz's grounded theory method. Single audio-recorded qualitative interviews with thirteen critical care nurses from four intensive care specialities: cardiac; general; neurological and renal were carried out. Interviews were facilitated by an end-of-life vignette developed with clinical collaborators. Across critical care areas four key dying trajectories were identified. These trajectories were shaped by contested boundaries associated with delayed or stalled decision-making around how withdrawal of treatment should proceed. Nurses provided end of life care (including collaborative and action-oriented skills) to shape the dying trajectory of patients so as to satisfy the wishes of the patient and family, and their own professional aims. Differing views as to when withdrawal of treatment should commence and how it should be operationalised appeared to be underpinned by the requirements of the role that health professionals fulfil, with doctors focusing on making withdrawal of treatment decisions, and nurse's being tasked with operationalising the processes that constitute it. Multidisciplinary teams need a 'shared' understanding of each other's roles, responsibilities, aims, and

Assisted dying - should the UK change its stance?

PubMed

Gordon, Daniel; Raphael, Claire E; Vassiliou, Vassilios

2015-04-01

Along with an increasing interest in assisted dying by many European and North American countries, some of which have already modified their existing laws to accommodate this, the interest in assisted dying in the UK has increased once again following Lord Falconer's Assisted Dying for the Terminally Ill Bill. Drawing on examples from countries where similar assisted dying laws are already in place, this article analyses and contextualises the proposed bill and discusses its potential pitfalls and benefits for the UK. © The European Society of Cardiology 2015 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

Meditations on the unitary rhythm of dying-grieving.

PubMed

Malinski, Violet M

2012-07-01

When someone faces loss of a loved one, that person simultaneously grieves and dies a little, just as the one dying also grieves. The author's personal conceptualization of dying and grieving as a unitary rhythm is explored based primarily on her interpretation of Rogers' science of unitary human beings, along with selected examples from related nursing literature and from the emerging focus on continuing bonds in other disciplines. Examples from contemporary songwriters that depict such a unitary conceptualization are given along with personal examples. The author concludes with her description of the unitary rhythm of dying-grieving.

Will the UK Supreme Court allow assisted dying?

PubMed

Griffith, Richard

MPs overwhelmingly voted against passing the Assisted Dying Bill into law in September 2015. The Bill was defeated by a majority of 212, despite the heartfelt pleas of many MPs to pass it into law. The size of the defeat means that it is unlikely that Parliament will consider a similar law for many years. Yet many considered the Bill their last opportunity to make assisted dying lawful. There is, however, one further possible way assisted dying could become lawful in the UK--and that would be where the Supreme Court allowed it. In this article, the author reviews the Supreme Court's decision in R (on the application of Nicklinson v Ministry of Justice [2014] and considers how likely it is that the Supreme Court will now sanction assisted dying following Parliament's refusal to enact an assisted dying law.

Exploring the concept of quality care for the person who is dying.

PubMed

Stefanou, Nichola; Faircloth, Sandra

2010-12-01

The concept of good quality care for the patient who is dying is diverse and complex. Many of the actions that are being taken to increase the quality of care of the dying patient are based around outcome, uniformity of service and standardization of process. There are two main areas that are referred to when dealing with care of the dying patient; end-of-life care and palliative care. High quality end-of-life care is increasingly recognized as an ethical obligation of health-care providers, clinicians and organizations, and yet there appears little evidence from the patients' perspective. There are many national and local initiatives taking place to improve the quality of care people receive towards the end of their life. This being said initiatives alone will not achieve good quality care and deliver good patient experiences. Only clinicians working at the front line can truly influence the way in which quality is improved and good experiences delivered.

Death and Dying--A Living Study. Profiles of Promise 35.

ERIC Educational Resources Information Center

Hawke, Sharryl

Realizing that all students have to deal with death at some time, yet receive no formal education in the subject, Alex Kramer, a high school teacher at Moon High School, Corapolis, Pennsylvania, decided to create a program which would give students an opportunity to study death and the process of dying as integral parts of life. Kramer's goals,…

Effect of triangular texture on the tribological performance of die steel with TiN coatings under lubricated sliding condition

NASA Astrophysics Data System (ADS)

Chen, Ping; Xiang, Xin; Shao, Tianmin; La, Yingqian; Li, Junling

2016-12-01

The friction and wear of stamping die surface can affect the service life of stamping die and the quality of stamping products. Surface texturing and surface coating have been widely used to improve the tribological performance of mechanical components. This study experimentally investigated the effect of triangular surface texture on the friction and wear properties of the die steel substrate with TiN coatings under oil lubrication. TiN coatings were deposited on a die steel (50Cr) substrate through a multi-arc ion deposition system, and then triangular surface texturing was fabricated by a laser surface texturing. The friction and wear test was conducted by a UMT-3 pin-on-disk tribometer under different sliding speeds and different applied loads, respectively. The adhesion test was performed to evaluate the effectiveness of triangular texturing on the interfacial bonding strength between the TiN coating and the die steel substrate. Results show that the combination method of surface texturing process and surface coating process has excellent tribological properties (the lowest frictional coefficient and wear volume), compared with the single texturing process or the single coating process. The tribological performance is improved resulting from the high hardness and low elastic modulus of TiN coatings, and the generation of hydrodynamic pressure, function of micro-trap for wear debris and micro-reservoirs for lubricating oil of the triangular surface texture. In addition, the coating bonding strength of the texturing sample is 3.63 MPa, higher than that of the single coating sample (3.48 MPa), but the mechanisms remain to be further researched.

Technische Systeme für den Herzersatz und die Herzunterstützung

NASA Astrophysics Data System (ADS)

Schöb, Reto; Loree, Howard M.

Herzkrankheiten verursachen allein in den Vereinigten Staaten jährlich mehr als 700’000 Todesfälle. Ungefähr 3 Millionen Patienten in den U.S.A. leiden gemäss der American Heart Association (AHA) und dem National Heart, Lung and Blood Institute (NHLBI) an kongestivem Herzversagen (Congestive Heart Failure, CHF), welches eine chronische, sehr entkräftende und degenerative Krankheit ist: Das Herz ist dabei unfähig, hinreichend Blut zu den Organen des Körpers zu pumpen. Über 400’000 Fälle von CHF werden jedes Jahr diagnostiziert. Ähnliche Zahlen werden für Europa und Japan zusammen geschätzt. Basierend auf Daten vom AHA und NHLBI beträgt die fünfjährige Überlebensrate für CHF-Patienten lediglich etwa 50% [1]. 70’000-120’000 dieser Patienten könnten von einer Herzverpflanzung profitieren. 1999 wurden in den USA aber nur 2185 Herztransplantationen durchgeführt während die Warteliste über 4000 Patienten beträgt [2]. Ein akuter Mangel an Spenderherzen und die enormen Kosten (250’000-400’000 USD pro Patient) sind die begrenzenden Faktoren für Herztransplantationen [3]. Dies bedeutet, dass eine riesige Anzahl von Patienten durch ein zuverlässiges und verschleissfreies, nichtthrombotisches, total implantierbares, künstliches Herz gerettet werden könnten. Bis heute jedoch kein derartiges Implantat kommerziell verfügbar.

Effects of climate-change induced vegetation die-off on soil biodiversity and functioning

NASA Astrophysics Data System (ADS)

Curiel Yuste, Jorge; Garcia Angulo, Daniel; Barba, Josep; Poyatos, Rafael

2017-04-01

Climate change-induced vegetation die-off is nowadays a widespread phenomenon responsible for limiting the capacity of terrestrial ecosystems to provide essential services worldwide. Less is known, however, about how vegetation die-off relates with changes in the biodiversity and ecology of the soil compartment, which accounts for many of the vital ecosystem functions such as providing essential nutrients for plant growth (nitrogen, N; or phosphorous, P), or long-term carbon (C) sequestration. The death of the vegetation alters soil abiotic (microclimate) conditions and limits the supply of the energy (carbohydrates specially) demanded by the soil biological communities. These abiotic and biotic changes triggers a cascade of causal-effect processes that may result in irreversible losses in soil biodiversity and in the stability of the trophic webs that sustain soil functions such as N fixation, mineralization of essential nutrients or C stabilization. However, to date, information on the potential impacts of climate-change induced vegetation die-off over soil biodiversity and functioning is fragmented (e.g. case-studies) and not very conclusive. We here want to summarize the state of the knowledge on all potential effects of climate-change induced vegetation die-off over soil biodiversity and soil functioning. Additionally, we also discuss the functional resilience of soils to climate-change vegetation die-off and how management practices could improve the resilience and the sustainability of the soil functioning.

Portable punch and die jig

DOEpatents

Lewandowski, Edward F.; Anderson, Petrus A.

1978-01-01

A portable punch and die jig includes a U-shaped jig of predetermined width having a slot of predetermined width in the base thereof extending completely across the width of the jig adapted to fit over the walls of rectangular tubes and a punch and die assembly disposed in a hole extending through the base of the jig communicating with the slot in the base of the jig for punching a hole in the walls of the rectangular tubes at precisely determined locations.

Harold S. Johnston (1920-2012)

NASA Astrophysics Data System (ADS)

Wuebbles, Donald

2013-02-01

One of the most exceptional atmospheric chemists of the twentieth century, Harold "Hal" S. Johnston died on 20 October 2012 at the age of 92. Hal's pioneering work on atmospheric kinetics, both in laboratory and theoretical studies, greatly advanced understanding of the processes affecting ozone in the troposphere and stratosphere, especially related to the chemistry and impacts resulting from nitrogen oxides (NOx ).

Improvement of Die Corner Filling in Box-shape Stepped Tubes Hydroforming

NASA Astrophysics Data System (ADS)

Hosseini-Farrash, S. H.; Elyasi, M.; Bakhshi-Jooybari, M.; Gorji, A.

2011-01-01

A new die design to improve the die corner filling in the hydroforming of square-sectional stepped tubes is presented. The proposed die-set contains two additional bushes, compared to the common tube hydroforming dies. First, the tube is placed into the die, filled with liquid, and sealed with the punches. Then, by increasing the internal pressure, the tube is bulged and contacts the die walls (bulging stage). By maintaining the internal pressure, the two upper and lower bushes move until the die cavity is filled completely (calibration stage). The proposed die was simulated and the results show that sharp corners of the part and relatively complete filling of the die cavity can be obtained by using this die set. In order to verify the results, some experiments have been carried out. The experimental results verified the results obtained from the simulations. The thickness distribution of the part is also investigated and it is shown that fairly uniform thickness distribution can be obtained by using the proposed die set.

Years after Inventors Die, Royalties Are Pennies from Heaven

ERIC Educational Resources Information Center

Blumenstyk, Goldie

2009-01-01

Sarah L. Kieweg had her own nice surprise when the University of Central Florida contacted her. She understood quite a bit about her father's pioneering work on artificial intelligence in the 1990s. Still, in 2006, eight years after he died of a heart attack, at age 50, the call from the university came out of the blue: some of James R. Driscoll's…

A Study on Segmented Multiple-Step Forming of Doubly Curved Thick Plate by Reconfigurable Multi-Punch Dies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ko, Young Ho; Han, Myoung Soo; Han, Jong Man

2007-05-17

Doubly curved thick plate forming in shipbuilding industries is currently performed by a thermal forming process, called as Line Heating by using gas flame torches. Due to the empirical manual work of it, the industries are eager for an alternative way to manufacture curved thick plates for ships. It was envisaged in this study to manufacture doubly curved thick plates by the multi-punch die forming. Experiments and finite element analyses were conducted to evaluate the feasibility of the reconfigurable discrete die forming to the thick plates. Single and segmented multiple step forming procedures were considered from both forming efficiency andmore » accuracy. Configuration of the multi-punch dies suitable for the segmented multiple step forming was also explored. As a result, Segmented multiple step forming with matched dies had a limited formability when the objective shapes become complicate, while a unmatched die configuration provided better possibility to manufacture large curved plates for ships.« less

Ageless Aluminum-Cerium-Based Alloys in High-Volume Die Casting for Improved Energy Efficiency

DOE PAGES

Stromme, Eric T.; Henderson, Hunter B.; Sims, Zachary C.; ...

2018-04-25

Strong chemical reactions between Al and Ce lead to the formation of intermetallics with exceptional thermal stability. The rapid formation of intermetallics directly from the liquid phase during solidification of Al-Ce alloys leads to an ultrafine microconstituent structure that effectively strengthens as-cast alloys without further microstructural optimization via thermal processing. Die casting is a high-volume manufacturing technology that accounts for greater than 40% of all cast Al products, whereas Ce is highly overproduced as a waste product of other rare earth element (REE) mining. Reducing heat treatments would stimulate significant improvements in manufacturing energy efficiency, exceeding (megatonnes/year) per large-scale heat-treatmentmore » line. In this study, multiple compositions were evaluated with wedge mold castings to test the sensitivity of alloys to the variable solidification rate inherent in high-pressure die casting. Once a suitable composition was determined, it was successfully demonstrated at 800 lbs/h in a 600-ton die caster, after which the as-die cast parts performed similarly to ubiquitous A380 in the same geometry without requiring heat treatment. Furthermore, this work demonstrates the compatibility of Al REE alloys with high-volume die-casting applications with minimal heat treatments.« less

Ageless Aluminum-Cerium-Based Alloys in High-Volume Die Casting for Improved Energy Efficiency

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stromme, Eric T.; Henderson, Hunter B.; Sims, Zachary C.

Strong chemical reactions between Al and Ce lead to the formation of intermetallics with exceptional thermal stability. The rapid formation of intermetallics directly from the liquid phase during solidification of Al-Ce alloys leads to an ultrafine microconstituent structure that effectively strengthens as-cast alloys without further microstructural optimization via thermal processing. Die casting is a high-volume manufacturing technology that accounts for greater than 40% of all cast Al products, whereas Ce is highly overproduced as a waste product of other rare earth element (REE) mining. Reducing heat treatments would stimulate significant improvements in manufacturing energy efficiency, exceeding (megatonnes/year) per large-scale heat-treatmentmore » line. In this study, multiple compositions were evaluated with wedge mold castings to test the sensitivity of alloys to the variable solidification rate inherent in high-pressure die casting. Once a suitable composition was determined, it was successfully demonstrated at 800 lbs/h in a 600-ton die caster, after which the as-die cast parts performed similarly to ubiquitous A380 in the same geometry without requiring heat treatment. Furthermore, this work demonstrates the compatibility of Al REE alloys with high-volume die-casting applications with minimal heat treatments.« less

Optimization of Composition and Heat Treating of Die Steels for Extended Lifetime

DOE Office of Scientific and Technical Information (OSTI.GOV)

David Schwam; John F. Wallace; Quanyou Zhou

2002-01-30

An ''average'' die casting die costs fifty thousand dollars. A die used in making die cast aluminum engine blocks can cost well over one million dollars. These costs provide a strong incentive for extension of die life. While vacuum quenched Premium Grade H13 dies have become the most widely used in the United States, tool makers and die casters are constantly searching for new steels and heat treating procedures to extend die life. This project was undertaken to investigate the effects of composition and heat treating on die life and optimize these parameters.

Energy-Saving Sintering of Electrically Conductive Powders by Modified Pulsed Electric Current Heating Using an Electrically Nonconductive Die

NASA Astrophysics Data System (ADS)

Ito, Mikio; Kawahara, Kenta; Araki, Keita

2014-04-01

Sintering of Cu and thermoelectric Ca3Co4O9 was tried using a modified pulsed electric current sintering (PECS) process, where an electrically nonconductive die was used instead of a conventional graphite die. The pulsed electric current flowed through graphite punches and sample powder, which caused the Joule heating of the powder compact itself, resulting in sintering under smaller power consumption. Especially for the Ca3Co4O9 powder, densification during sintering was also accelerated by this modified PECS process.

Dying in the age of choice.

PubMed

Black, Kathy; Csikai, Ellen L

2015-01-01

Due to the unprecedented increase in the United States aging demographics, many more people are living longer and reaching older ages than ever before. However, a longer life is not necessarily a better life, as the vast majority will face a period of prolonged deteriorating health prior to death. Although notable efforts have been underway that are designed to improve the end-of-life experience, increasing numbers of individuals express a desire and/or act upon an intent to end their lives precipitously. Though still limited, the options to actively participate in their own deaths are growing. Requests for a hastened death can occur among people of all ages and includes those with advanced illness as well as others wanting to die due to unbearable suffering. This article provides an overview of the ongoing discourse about the experience of dying faced by many older adults, including aspects frequently associated with "a good death." The limitations of established practices which seek to provide a "better" dying experience are identified followed by discussion of the growing availability of alternative options. Reflective considerations are presented to guide practice vis-à-vis the changing landscape surrounding options in dying.

[Dying well seen in the light of self-transcendence and transition : two theories of care helpful to nurses].

PubMed

Laporte, Pauline; Vonarx, Nicolas

2016-06-01

Accompanying a dying person up to and at the actual moment of death is a duty that often leaves carers at a loss. We shall show how far theoretical nursing knowledge can help practitioners who accompany the end of life by applying two theories of care : Reed’s theory of self-transcendence and Meleis’s theory of transition. Our interpretation of the theory of self-transcendence designates three points of reference in the concept of dying well. The first relates to the overtures prompted by the vulnerability that the context of dying inspires. The second concerns the capacity of the patient to summon up intrapersonal, interpersonal and transpersonal strategies, and the third considers the benefits when self-transcendence is achieved. The theory of transition similarly presents three points of reference. The first is based on informing the patient about palliative care and telling him or her the truth about the prognosis. The second relates to coordinating the interprofessional team that is looking after the dying person. The last criterion is that the palliative care should be started at a suitable moment. This makes it possible to educate a patient who wishes to die at home and thus create an environment favourable to the transition.

Feasibility of conducting prospective observational research on critically ill, dying patients in the intensive care unit.

PubMed

van Beinum, Amanda; Hornby, Laura; Dhanani, Sonny; Ward, Roxanne; Chambers-Evans, Jane; Menon, Kusum

2017-01-01

Studying patients during the end of life is important, as it has the potential to lead to improvements in care for the dying. For patients who die after a controlled withdrawal of life-sustaining therapies in the intensive care unit, information about the natural history of death and the process of removing life support has additionally led to advances in practice for deceased organ donation. However, this unique population of severely critically ill and imminently dying patients has been difficult to study, largely due to assumptions made by research teams and ethics boards alike about the logistical difficulties of obtaining consent and completing research procedures before or during the process of withdrawal of life-sustaining therapies. In this paper, we describe the ethics substudy of the first prospective observational research study in Canada to obtain consent and collect clinical data on patients during the process of withdrawal of life-sustaining therapies in the intensive care unit. We describe in detail the process of protocol development, review by five institutional research ethics boards and bedside staff satisfaction with the study. We conclude that prospective research on a critically ill and imminently dying population is feasible and can be conducted in an ethical manner. Further information is needed about the experiences and motivations of families and substitute decision makers who provide consent for research on critically ill intensive care unit patients at the end of life. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

An investigation on die crack detection using Temperature Sensitive Parameter for high speed LED mass production

NASA Astrophysics Data System (ADS)

Annaniah, Luruthudass; Devarajan, Mutharasu; San, Teoh Kok

To ensure the highest quality & long-term reliability of LED components it is necessary to examine LED dice that have sustained mechanical damage during the manufacturing process. This paper has demonstrated that detection of die crack in mass manufactured LEDs can be achieved by measuring Temperature Sensitive Parameters (TSPs) during final testing. A newly-designed apparatus and microcontroller was used for this investigation in order to achieve the millisecond switching time needed for detecting thermal transient effects and at the same time meet the expected speed for mass manufacturing. Evaluations conducted at lab scale shows that thermal transient behaviour of cracked die is significantly different than that of an undamaged die. Having an established test limits to differentiate cracked dice, large volume tests in a production environment were used to confirm the effectiveness of this test method. Failure Bin Analysis (FBA) of this high volume experiment confirmed that all the cracked die LEDs were detected and the undamaged LEDs passed this test without over-rejection. The work verifies that tests based on TSP are effective in identifying die cracks and it is believed that the method could be extended to other types of rejects that have thermal transient signatures such as die delamination.

Darwin als Sehhilfe für die Psychologie - Evolutionspsychologie

NASA Astrophysics Data System (ADS)

Schwab, Frank

Im Folgenden geht es um Einäugige, stereoskopisches Sehen, weite und enge Horizonte, Monokel und Sonnenbrillen. Der Beitrag versucht die Metapher des Sehens und der Sehhilfen anzuwenden, um so zu verdeutlichen, welchen Gewinn die herkömmliche Psychologie durch die Verwendung einer Darwin'schen Brille erlangen kann.

Low Temperature Consolidation of Micro/Nanosilver Die-Attach Preforms

NASA Astrophysics Data System (ADS)

McCoppin, Jared; Reitz, Thomas L.; Miller, Ryan; Vijwani, Hema; Mukhopadhyay, Sharmila; Young, Daniel

2014-09-01

Organically passivated silver nanopowder paste-based sintering is considered a promising solution for die-attach in high temperature power and sensing electronic devices. However, oxygen requirements during burnout and inherently high shrinkage rates limit their use to small die sizes. This work reports an alternative fabrication method that resolves decomposition and shrinkage issues of the die-attach by utilizing a prestressed optimized tape cast mixture of micro- and nanosilver particles with a polypropylene carbonate binder. The effects of prestressing, micro/nanosilver bimodal distribution, and polymer content on resulting microstructure and shear strength were investigated. Prior to application as a die-attach, uniaxial compression of the tape was found to significantly decrease shrinkage and improve green strength. This pre-stressing strategy allows for a decoupling of the resulting die-attach materials properties from the pressure applied during assembly. Bimodal mixtures consisting of 1-3 μm spherical powders with nanosilver resulted in shear strengths comparable to those of pure nanosilver. Shear strength decreased as bimodal particle size increased above 5 μm. A polymer content of ˜10 wt.% polypropylene carbonate combined with prestressing was identified as optimal for maximizing die-attach shear strength while still maintaining pliability and formability. Tape casts that were prestressed to 212 MPa by uniaxially compression and formulated with 10 wt.% of polypropylene carbonate resulted in a die-attach material with a shear strength of 54 MPa when sintered. These materials were used to demonstrate void-free 25-mm2 die-attach assemblies, suggesting that tape cast micro/nanosilver materials may be a promising die-attach method for high temperature and large-area electronics devices.

Digitalisierung und Energie 4.0 - Wie schaffen wir die digitale Energiewende?

NASA Astrophysics Data System (ADS)

Irlbeck, Maximilian

Die digitale Energiewende verändert nachhaltig die Systeme der "alten" Energiewelt. Ein Zusammenwachsen verschiedener Domänen im Energiesystem, die durch digitale Technologie möglich wird, birgt enorme Herausforderungen, ist aber notwendig, um die Energiewende und ihre Ziele zu meistern. Dieser Beitrag beschreibt die Wirkung der Digitalisierung auf das Energiesystem, listet Charakteristika der digitalen Energiewende auf und schildert für verschiedene Domänen mögliche Zielvorstellungen, die durch digitale Technologie umsetzbar sind. Am Ende erläutert der Beitrag Handlungsschritte, die auf dem Weg zu einem erneuerbaren Energiesystem gegangen werden sollten und zeigt Probleme und Risiken einer Fehlentwicklung auf.

Language used by health care professionals to describe dying at an acute care hospital.

PubMed

Wentlandt, Kirsten; Toupin, Philippe; Novosedlik, Natalia; Le, Lisa W; Zimmermann, Camilla; Kaya, Ebru

2018-05-21

To understand the language used to describe the deterioration and death of patients in an acute academic tertiary care centre, and to identify whether patient diagnoses or palliative care(PC) involvement was associated with clearer descriptions of this process. We conducted a retrospective chart review of the final admission of 150 patients who died on an inpatient internal medicine unit. Conventional and summative content analysis was performed of the language used to describe, either directly or indirectly, that the patient's death was imminent. Of the 150 deaths, the median age was 79.5(range22-101), 58% were male, and 69% spoke English. A total of 45% of deaths were from cancer, and 66% occurred with prior PC team involvement. There was no documentation of the dying process in 18(12%) of charts. In the remainder, clinicians' documentation of imminent death fell into three categories: 1 identification of the current state using specific labels, e.g. 'dying'(24.7%), or 'end of life'(15.3%), or less specific language, 'unwell' or 'doing poorly'(6.0%); 2 predicting the future state using specific or more vague predictions: e.g.'hours to days'(7.3%) or 'poor or guarded prognosis'(26.0%); 3 using care provided to the patient to imply patient status: e.g. palliative care(49.3%) or comfort care(28.7%). PC involvement, but not a malignant diagnosis, was associated with more frequent use of specific language to describe the current(p=0.004) or future state(p=0.02). Death and dying in hospital is inadequately documented and is often described using unclear and vague language. PC involvement is associated with clearer language to describe this process. Copyright © 2018. Published by Elsevier Inc.

Threatened with death but growing: changes in and determinants of posttraumatic growth over the dying process for Taiwanese terminally ill cancer patients.

PubMed

Tang, Siew Tzuh; Lin, Kuan-Chia; Chen, Jen-Shi; Chang, Wen-Cheng; Hsieh, Chia-Hsun; Chou, Wen-Chi

2015-02-01

Posttraumatic growth at end of life, a positive psychological consequence of dealing with a life crisis, may be catalyzed by the trauma of facing mortality. Studies on cancer patients' posttraumatic growth have overwhelmingly examined early-stage survivors. Of the few studies on advanced cancer patients, none anchored posttraumatic growth with the patient's death. Therefore, the purposes of this study were to describe longitudinal changes in and to identify determinants of posttraumatic growth over the dying process. A convenience sample of 313 cancer patients was recruited and followed until death. Posttraumatic growth was measured by the Posttraumatic Growth Inventory. Determinants were evaluated from sociodemographics, cancer characteristics, social context variables, and coping strategies using a multiple linear regression model. The dying process may be too threatening and stressful for cancer patients to experience profound posttraumatic growth as manifested by low Posttraumatic Growth Inventory scores (26.13 ± 21.59 to 40.33 ± 27.71 on a 0-105 scale) without significant changes as death approached. However, terminally ill cancer patients who were not defeated by the initial threat of death experienced posttraumatic growth. Patients were at risk for low-level posttraumatic growth if they were male, were non-middle aged, had low educational attainment, had a non-metastatic disease, recently recognized terminally ill status, had severe symptom distress, had high functional dependence and weak social support, and were unaware or had low acceptance of their prognosis. Interventions are needed to appropriately relieve symptom distress, facilitate functional independence, enhance social support, and improve prognostic awareness and acceptance to inspire positive changes for cancer patients at end of life. Copyright © 2014 John Wiley & Sons, Ltd.

Killing, letting die and euthanasia.

PubMed Central

Husak, D N

1979-01-01

Medical ethicists debate whether or not the moral assessment of cases of euthanasia should depend on whether the patient is 'killed' or 'allowed to die'. The usual presupposition is that a clear distinction between killing and letting die can be drawn so that this substantive question is not begged. I contend that the categorisation of cases of instances of killing rather than as instances of letting die depends in part on a prior moral assessment of the case. Hence is it trivially rather than substantively true that the distinction has moral significance. But even if a morally neutral (ie non-question begging) distinction could be drawn, its application to the euthanasia controversy is problematic. I illustrate the difficulties of employing this distinction to reach moral conclusions by critically discussing Philippa Foot's recent treatment of euthanasia. I conclude that even if an act of euthanasia is an instance of killing, and there exists a prima facie moral duty not to kill, and no more stringent duty overrides this duty, one still cannot determine such an act to be morally impermissible. PMID:541821

Killing, letting die and euthanasia.

PubMed

Husak, D N

1979-12-01

Medical ethicists debate whether or not the moral assessment of cases of euthanasia should depend on whether the patient is 'killed' or 'allowed to die'. The usual presupposition is that a clear distinction between killing and letting die can be drawn so that this substantive question is not begged. I contend that the categorisation of cases of instances of killing rather than as instances of letting die depends in part on a prior moral assessment of the case. Hence is it trivially rather than substantively true that the distinction has moral significance. But even if a morally neutral (ie non-question begging) distinction could be drawn, its application to the euthanasia controversy is problematic. I illustrate the difficulties of employing this distinction to reach moral conclusions by critically discussing Philippa Foot's recent treatment of euthanasia. I conclude that even if an act of euthanasia is an instance of killing, and there exists a prima facie moral duty not to kill, and no more stringent duty overrides this duty, one still cannot determine such an act to be morally impermissible.

Kundenfokus: Startpunkt für die digitale Transformation bei Stadtwerken

NASA Astrophysics Data System (ADS)

Fett, Perry; Küller, Philipp

Big Data, Internet der Dinge, Mobile Computing und soziale Medien - die modernen Informationstechnologien durchdringen den Alltag der meisten Menschen und lösen hierdurch eine digitale Transformation aus. Im Unternehmenskontext manifestiert sich die Digitalisierung durch eine neue Qualität der wissensbasierten Entscheidungsunterstützung und der Automatisierung bzw. Autonomisierung der Geschäftsprozesse. Für Stadtwerke gilt es nun, die Chancen der Digitalisierung zu ihren Gunsten zu nutzen. Ein Startpunkt könnte hierbei sein, wie Stadtwerke zukünftig mit ihren Kunden interagieren. Ausgelöst durch die Liberalisierung der Märkte rückt der Kunde heute stärker in den Mittelpunkt - die Energiewirtschaft steht nun vor der Herausforderung, dem Wettbewerb einen Schritt voraus zu sein und dem Kunden ein absolut positives Kundenerlebnis (Customer Experience) sowohl als Maßnahme zur Kundenbindung als auch zum Kundenaufbau zu bieten. Das vorliegende Kapitel zeigt hierfür die Erfolgskriterien für die gelungene Etablierung des Kundenfokus im eigenen Unternehmen auf. Mit dem Customer-Focus-Cycle-Modell von Fujitsu, angelehnt an den Deming-Kreislauf, wird ein allgemeingültiger Ansatz für ein mögliches Vorgehen beim Aufbau des Kundenfokus vorgestellt. Die sechs Phasen werden dabei anhand praktischer Beispiele erläutert und geben zudem Hinweise zu Methoden und Tools. Aus dem vorgestellten "Werkzeugkasten" wird ferner die Customer-Journey-Methode im Detail erläutert. Weiter soll das präsentierte Reifegradmodell Unternehmen dabei unterstützen, den eigenen Status quo festzustellen und die persönlichen Ziele auf dem Weg zur kundenzentrierten Organisation festzulegen.

[Heatwaves and population die off in the Voronezh city].

PubMed

Mekhant'ev, I I; Pichuzhkina, N M; Masaĭlova, L A

2013-01-01

Climatic factor is most important condition for the formation of public health. Attention to it has increased recently against the background of global and regional climate change. The aim of the study was to investigate the effect of air temperature on population die off in the Voronezh city in the period of fire-related emergencies. Assessment of cause-and-effect relationships between the air temperature and daily death cases s was performed with the help of the method of time series. Correlation analysis showed a statistically significant positive relationship between air temperature and population die off from all causes and from diseases of the circulatory system with a lag of 0, 1, 2, 3 days; respiratory diseases - with a lag of 3 days. With the gain in air temperature by one degree the number of deaths increases by 3%. The results were used in adopt management decisions on minimization risks and potential negative effects on human health.

Why do older people oppose physician-assisted dying? A qualitative study.

PubMed

Malpas, Phillipa J; Wilson, Maria K R; Rae, Nicola; Johnson, Malcolm

2014-04-01

Physician-assisted dying at the end of life has become a significant issue of public discussion. While legally available in a number of countries and jurisdictions, it remains controversial and illegal in New Zealand. The study aimed to explore the reasons some healthy older New Zealanders oppose physician-assisted dying in order to inform current debate. Recorded interviews were transcribed and analysed by the authors after some edits had been made by respondents. In all, 11 older participants (over 65 years) who responded to advertisements placed in Grey Power magazines and a University of Auckland email list were interviewed for around 1 h and asked a number of open-ended questions. Four central themes opposing physician-assisted dying were identified from the interviews: one's personal experience with health care and dying and death, religious reasoning and beliefs, slippery slope worries and concern about potential abuses if physician-assisted dying were legalised. An important finding of the study suggests that how some older individuals think about physician-assisted dying is strongly influenced by their past experiences of dying and death. While some participants had witnessed good, well-managed dying and death experiences which confirmed for them the view that physician-assisted dying was unnecessary, those who had witnessed poor dying and death experiences opposed physician-assisted dying on the grounds that such practices could come to be abused by others.

Microstructure development and texture evolution of aluminum multi-port extrusion tube during the porthole die extrusion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fan, X.H.

Aluminum multi-port extrusion tube is processed by the porthole die extrusion and the internal tube walls are welded through the solid state metallurgical bonding. In order to observe the development of grains and their orientations under severe plastic deformation and solid state welding, the extrusion butt together with the die is quenched immediately after extrusion to preserve the grain structure in the processing. The forming histories of selected material points are obtained by analyzing the optical microscopy graph. The evolution of the microstructure along the forming path is characterized by electro backscattered diffraction. It is found that geometrical dynamic recrystallizationmore » happens in the process. Grains are elongated, scattered at the transition zone and shear intensive zone, and then pinched off when they are pushed out from the die orifice. The shear-type orientations are predominant at the surface layer on the longitudinal section of the tube web and have penetrated into the intermediate layer. The rolling-type orientations are formed at the central layer. Texture gradient through the thickness of the tube web is observed. And cube orientated grains are found at the seam weld region. - Highlights: •Microstructure of extrusion butt is preserved after the micro scale porthole die extrusion. •Grain morphology history along forming path is investigated. •Texture evolutions on three material flows are present. •Texture gradient exists on the longitudinal section of the internal wall of profile. •Rolling-type and cube textures are found at the solid state welding region.« less

Simulation of 7050 Wrought Aluminum Alloy Wheel Die Forging and its Defects Analysis based on DEFORM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang Shiquan; Yi Youping; Zhang Yuxun

2010-06-15

Defects such as folding, intercrystalline cracking and flow lines outcrop are very likely to occur in the forging of aluminum alloy. Moreover, it is difficult to achieve the optimal set of process parameters just by trial and error within an industrial environment. In producing 7050 wrought aluminum alloy wheel, a rigid-plastic finite element method (FEM) analysis has been performed to optimize die forging process. Processing parameters were analyzed, focusing on the effects of punch speed, friction factor and temperature. Meanwhile, mechanism as well as the evolution with respect to the defects of the wrought wheel was studied in details. Frommore » an analysis of the results, isothermal die forging was proposed for producing 7050 aluminum alloy wheel with good mechanical properties. Finally, verification experiment was carried out on hydropress.« less

Cascaded die mountings with spring-loaded contact-bond options

DOEpatents

Hsu, John S.; Adams, Donald J.; Su, Gui-Jia; Marlino, Laura D.; Ayers, Curtis W.; Coomer, Chester

2005-08-16

A cascaded die mounting device and method using spring contacts for die attachment, with or without metallic bonds between the contacts and the dies, is disclosed. One embodiment is for the direct refrigerant cooling of an inverter/converter carrying higher power levels than most of the low power circuits previously taught, and does not require using a heat sink.

Machining of Silicon-Ribbon-Forming Dies

NASA Technical Reports Server (NTRS)

Menna, A. A.

1985-01-01

Carbon extension for dies used in forming silicon ribbon crystals machined precisely with help of special tool. Die extension has edges beveled toward narrow flats at top, with slot precisely oriented and centered between flats and bevels. Cutting tool assembled from standard angle cutter and circular saw or saws. Angle cutters cuts bevels while slot saw cuts slot between them. In alternative version, custom-ground edges or additional circular saws also cut flats simultaneously.

25 CFR 301.3 - Specifications of dies.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 2 2010-04-01 2010-04-01 false Specifications of dies. 301.3 Section 301.3 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR NAVAJO, PUEBLO, AND HOPI SILVER AND TURQUOISE... more mechanical than hand tools and vise. Dies shall contain only a single element of the design. ...

Physical and Psychological Distress Are Related to Dying Peacefully in Residents With Dementia in Long-Term Care Facilities.

PubMed

De Roo, Maaike L; Albers, Gwenda; Deliens, Luc; de Vet, Henrica C W; Francke, Anneke L; Van Den Noortgate, Nele; Van den Block, Lieve

2015-07-01

Although dying peacefully is considered an important outcome of high-quality palliative care, large-scale quantitative research on dying peacefully and the factors associated with a peaceful death is lacking. To gain insight into how many residents with dementia in long-term care facilities die peacefully, according to their relatives, and whether that assessment is correlated with observed physical and psychological distress. This was a retrospective cross-sectional study of deceased nursing home residents in a representative sample of long-term care facilities in Flanders, Belgium (2010). Structured post-mortem questionnaires were completed by relatives of the resident, who were asked to what extent they agreed that the resident "appeared to be at peace" during the dying process. Spearman correlation coefficients gave the correlations between physical and psychological distress (as measured using the Symptom Management at the End of Life with Dementia and Comfort Assessment in Dying at the End of Life with Dementia scales) and dying peacefully (as measured using the Quality of Dying in Long Term Care instrument). The sample comprised 92 relatives of deceased residents with dementia. In 54% of cases, relatives indicated that the resident died peacefully. Weak-to-moderate correlations (0.2-0.57) were found between dying peacefully and physical distress in the last week of life. Regarding psychological distress, weak-to-moderate correlations were found for both the last week (0.33-0.44) and last month of life (0.28-0.47). Only half of the residents with dementia died peacefully as perceived by their relatives. Relatives' assessment of whether death was peaceful is related to both physical and psychological distress. Further qualitative research is recommended to gain more in-depth insights into the aspects on which relatives base their judgment of dying peacefully. Copyright © 2015 American Academy of Hospice and Palliative Medicine. Published by Elsevier Inc. All

A Hollow Extrusion Die for Big Square Tube Profiles of Al-alloy

NASA Astrophysics Data System (ADS)

Huang, Xuemei; Deng, Rurong

2018-03-01

The factors on premature failure of the traditional extrusion die for the big square tube profiles were introduced. And the characteristics of the conventional structure were analyzed. A new type of hollow die structure for these profiles was presented. And the composition elements of the new die structure were described, including its advantages. According to the comparison conventional with new die structure in use, it was shown that the new die structure has obvious advantages, it could greatly improve the die life. This is a type of die structure which is worth promoting.

Survey on death and dying in Hong Kong: attitudes, beliefs, and preferred end-of-life care.

PubMed

Mjelde-Mossey, Lee Ann; Chan, Cecilia L W

2007-01-01

Social Workers in end-of-life and palliative care have a particular opportunity to ease the dying process by providing culturally appropriate services to the dying and their families. In today's multicultural social environment, with an ever-increasing immigrant population, social workers are challenged to be knowledgeable about diverse cultures. Recently, a forum of health care professionals and social workers in Hong Kong conducted a survey of the general population to assess death and dying attitudes, beliefs, and preferences for end-of-life care. Four-hundred-thirty Hong Kong Chinese participated in a telephone interview. Responses were compared by gender. The survey results not only contribute to an understanding of Hong Kong Chinese, but can inform social workers who practice with Chinese immigrants to the United States.

A sheet metal forming simulation of automotive outer panels considering the behavior of air in die cavity

NASA Astrophysics Data System (ADS)

Choi, Kwang Yong; Kim, Yun Chang; Choi, Hee Kwan; Kang, Chul Ho; Kim, Heon Young

2013-12-01

During a sheet metal forming process of automotive outer panels, the air trapped between a blank sheet and a die tool can become highly compressed, ultimately influencing the blank deformation and the press force. To prevent this problem, vent holes are drilled into die tools and needs several tens to hundreds according to the model size. The design and the drilling of vent holes are based on expert's experience and try-out result and thus the process can be one of reasons increasing development cycle. Therefore the study on the size, the number, and the position of vent holes is demanded for reducing development cycle, but there is no simulation technology for analyzing forming defects, making numerical sheet metal forming process simulations that incorporate the fluid dynamics of air. This study presents a sheet metal forming simulation of automotive outer panels (a roof and a body side outer) that simultaneously simulates the behavior of air in a die cavity. Through CAE results, the effect of air behavior and vent holes to blank deformation was analyzed. For this study, the commercial software PAM-STAMP{trade mark, serif} and PAM-SAFE{trade mark, serif} was used.

Plastohydrodynamic drawing and coating of stainless steel wire using a tapered bore die of no metal to metal contact

NASA Astrophysics Data System (ADS)

Hasan, S.; Basmage, O.; Stokes, J. T.; Hashmi, M. S. J.

2018-05-01

A review of wire coating studies using plasto-hydrodynamic pressure shows that most of the works were carried out by conducting experiments simultaneously with simulation analysis based upon Bernoulli's principle and Euler and Navier-Stokes (N-S) equations. These characteristics relate to the domain of Computational Fluid Dynamics (CFD) which is an interdisciplinary topic (Fluid Mechanics, Numerical Analysis of Fluid flow and Computer Science). This research investigates two aspects: (i) simulation work and (ii) experimentation. A mathematical model was developed to investigate the flow pattern of the molten polymer and pressure distribution within the wire-drawing dies, assessment of polymer coating thickness on the coated wires and speed of coating on the wires at the outlet of the drawing dies, without deploying any pressurizing pump. In addition to a physical model which was developed within ANSYS™ environment through the simulation design of ANSYS™ Workbench. The design was customized to simulate the process of wire-coating on the fine stainless-steel wires using drawing dies having different bore geometries such as: stepped parallel bore, tapered bore and combined parallel and tapered bore. The convergence of the designed CFD model and numerical and physical solution parameters for simulation were dynamically monitored for the viscous flow of the polypropylene (PP) polymer. Simulation results were validated against experimental results and used to predict the ideal bore shape to produce a thin coating on stainless wires with different diameter. Simulation studies confirmed that a specific speed should be attained by the stainless-steel wires while passing through the drawing dies. It has been observed that all the speed values within specific speed range did not produce a coating thickness having the desired coating characteristic features. Therefore, some optimization of the experimental set up through design of experiments (Stat-Ease) was applied to

Development and Evaluation of Die Materials for Use in the Growth of Silicon Ribbons by the Inverted Ribbon Growth Process. Task 2: LSSA Project

NASA Technical Reports Server (NTRS)

Duffy, M. T.; Berkman, S.; Moss, H. I.; Cullen, G. W.

1978-01-01

Several ribbon growth experiments were performed from V-shaped dies coated with CVD Si3N4. The most significant result was the ability to perform five consecutive growth runs from the same die without mechanical degradation of the die through temperature cycling. The die was made from vitreous carbon coated with CVD Si3N4. Silicon oxynitride, Si2N2O, was examined with respect to thermal stability in contact with molten silicon. The results of X-ray analysis indicate that this material is converted to both alpha - and beta-Si3N4 in the presence of molten silicon. Experiments on the stability of CVD SiOxNy shoe that this material can be maintained in contact with molten silicon (sessile drop test) for greater than 30 h at 1450 C without total decompositon. These layers are converted mainly to beta-Si3N4.

Margin adaptation of indirect composite inlays fabricated on flexible dies.

PubMed

Price, R B; Gerrow, J D

2000-03-01

Indirect composite restorations can be made in 1 appointment using a flexible die. Interactions between different impression materials and flexible die materials may affect the accuracy of fit and margin adaptation of the restoration. This study compared the margin adaptation of composite inlays made using the following 5 impression/flexible die material combinations; condensation silicone/polyvinyl siloxane (CS/PVS), wash viscosity polyvinyl siloxane/medium or heavy viscosity polyvinyl siloxane (PVS/PVS), irreversible hydrocolloid impression/medium viscosity polyvinyl siloxane (IH/PVS), wash viscosity polyvinyl siloxane impression/polyether (PVS/PE), with composite inlays made using a control system of a wash viscosity polyvinyl siloxane impression and a type IV stone die. For each test and control system, 10 impressions were made of a class II composite inlay preparation in a metal master die. One die was made from each impression and one composite inlay was made and finished on each die (a total of 60 inlays). Inlays were placed on the master die and the margin opening at the buccal, distal, and gingival sites was recorded with a measuring microscope (x40 magnification). The overall mean +/- SD margin openings of inlays made from the systems were as follows: PVS wash/PVS heavy viscosity 149.5 +/- 107. 4 microm; PVS wash/PVS medium viscosity 87.4 +/- 63.0 microm; IH/PVS medium viscosity 76.7 +/- 48.9 microm; CS/PVS 73.3 +/- 48.7 microm, PVS wash viscosity/PE 64.0 +/- 44.3 microm, PVS wash viscosity/stone 53.9 +/- 48.3 microm. Composite inlays made using the PVS wash viscosity/PVS heavy viscosity system had significantly larger distal, gingival, and overall mean margin openings than all other inlays (ANOVA and Fisher PLSD test; P =.05). The separating medium required between some impression and die materials did not work consistently. Composite inlays fabricated on dies made of material different than the impression material had mean buccal, distal, gingival, and

The Right To Die. Public Talk Series.

ERIC Educational Resources Information Center

Pasquerella, Lynn

This program guide on the right to die provides policy issue information where ethical concerns have a prominent place. Three positions about the right to die are presented: (1) mercy killing and assisted suicide should be legally permitted in certain cases; (2) legal status should be given to living wills and other advance directives that would…

Digitalisierung als Inkubator für die Energieversorgung von morgen

NASA Astrophysics Data System (ADS)

Arnold, Christian; Postina, Matthias

Neue Treiber der Digitalisierung bestimmen die Geschicke der etablierten Unternehmen im Energiebereich, dabei haben diese in vielen Fällen noch nicht einmal adäquat auf die altbekannten Treiber der Energiewende reagiert. Eine ganze Branche ist im Umbruch, alte Erlösmodelle brechen ein und Einigkeit scheint bei den Verantwortlichen nur in der Frage zu herrschen, wie in Zukunft noch Geld verdient werden kann. Dieser Beitrag erklärt die prägenden Treiber der Veränderung, analysiert die Ausgangslage und nennt Herausforderungen der Branche. Darüber hinaus legt er den Fokus auf die Betrachtung der neuen digitalen Wertschöpfung. Dazu wird ein Modell eingeführt, welches von der klassischen Wertschöpfungskette über datenbasierte Geschäftsmodelle im Energiesystem bis hin zum Internet of Smart Services reicht. Mit dem Modell geben die Autoren gleichsam Einblick in das geplante Energiewendeprojekt enera.

[Dying with cancer: Hollywood lessons].

PubMed

Niemeyer, Fernanda; Kruse, Maria Henriqueta Luce

2013-12-01

The study attempts to understand how dying from cancer is portrayed by five movies produced in Hollywood between 1993 and 2006. Based on the cultural studies and their post-structuralism version and supported by the notions of discourse and subjectivity, as proposed by philosopher Michel Foucault, we suggest one of the possible readings of the movie picture corpus. We assess how the movie picture discourse acts as a cultural pedagogy that produces ways of seeing dying with cancer: immortalizing the healthy body image, silencing death, taking care of the dead body and, finally, accepting death. Our proposal is intended to stimulate reflections that may contribute to care and education in nursing.

Live to die another way: modes of programmed cell death and the signals emanating from dying cells

PubMed Central

Fuchs, Yaron; Steller, Hermann

2015-01-01

Preface All life ends in death, but perhaps one of life’s grander ironies is that it also depends on death. Cell-intrinsic suicide pathways, termed programmed cell death (PCD), are crucial for animal development, tissue homeostasis and pathogenesis. Originally, PCD was virtually synonymous with apoptosis, but recently, alternative PCD mechanisms have been reported. Here, we provide an overview of several distinct PCD mechanisms, namely apoptosis, autophagy and necroptosis. In addition, we discuss the complex signals emanating from dying cells, which can either fuel regeneration or instruct additional killing. Further advances in understanding the physiological role of multiple cell death mechanisms and associated signals will be important to selectively manipulate PCD for therapeutic purposes. PMID:25991373

Faster, Less Expensive Dies Using RSP Tooling

NASA Astrophysics Data System (ADS)

Knirsch, James R.

2007-08-01

RSP Tooling is an indirect spray form additive process that can produce production tooling for virtually any forming process and from virtually any metal. In the past 24 months a significant amount of research and development has been performed. This resulted in an increase in the basic metallurgical understanding of what transpires during the rapid solidification of the metal, significant improvements in the production machine up time, ceramic developments that have improved finish, process changes that have resulted in a shorter lead time for tool delivery, and the testing of many new alloys. RSP stands for Rapid Solidification Process and is the key to the superior metallurgical properties that result from the technology. Most metals that are sprayed in the process leave the machine with the same physical properties as the same metal normally achieves through heat treatment and in some cases the properties are superior. Many new applications are being pursued including INVAR tools for aerospace composite materials, and bimetallic tools made from tool steel and beryllium copper for die casting and plastic injection molding. Recent feasibility studies have been performed with tremendous success.

Tool & Die Technician.

ERIC Educational Resources Information Center

Ohio State Univ., Columbus. Center on Education and Training for Employment.

This document contains 23 units to consider for use in a tech prep competency profile for the occupation of tool and die technician. All the units listed will not necessarily apply to every situation or tech prep consortium, nor will all the competencies within each unit be appropriate. Several units appear within each specific occupation and…

Dying to Play.

ERIC Educational Resources Information Center

Miller, John K.

1998-01-01

In August 1995, a young football player died as a result of heat exhaustion suffered on the first day of football practice in Arkansas. Spurred by this tragedy, the district made some changes that every school district with an athletic program should consider. These include using a heat-stress monitor; abandoning the practice of group physical…

Mu opioid receptor availability in people with psychiatric disorders who died by suicide: a case control study

PubMed Central

2012-01-01

Background Mu opioid receptors have previously been shown to be altered in people with affective disorders who died as a result of suicide. We wished to determine whether these changes were more widespread and independent of psychiatric diagnoses. Methods Mu receptor levels were determined using [3 H]DAMGO binding in BA24 from 51 control subjects; 38 people with schizophrenia (12 suicides); 20 people with major depressive disorder (15 suicides); 13 people with bipolar disorder (5 suicides) and 9 people who had no history of psychiatric disorders but who died as a result of suicide. Mu receptor levels were further determined in BA9 and caudate-putamen from 38 people with schizophrenia and 20 control subjects using [3 H]DAMGO binding and, in all three regions, using Western blots. Data was analysed using one-way ANOVAs with Bonferroni’s Multiple Comparison Test or, where data either didn’t approximate to a binomial distribution or the sample size was too small to determine distribution, a Kruskal-Wallis test with Dunn’s Multiple Comparison Test. Results [3 H]DAMGO binding density was lower in people who had died as a result of suicide (p<0.01). People with schizophrenia who had died as a result of suicide had lower binding than control subjects (p<0.001), whilst people with bipolar disorder (non- suicide) had higher levels of binding (p<0.05). [3 H]DAMGO binding densities, but not mu protein levels, were significantly decreased in BA9 from people with schizophrenia who died as a result of suicide (p<0.01). Conclusions Overall these data suggest that mu opioid receptor availability is decreased in the brains of people with schizophrenia who died as a result of suicide, which would be consistent with increased levels of endogenous ligands occupying these receptors. PMID:22925223

Dying star creates sculpture of gas and dust

NASA Astrophysics Data System (ADS)

2004-09-01

Sculpture of gas and dust hi-res Size hi-res: 125 Kb Credits: ESA, NASA, HEIC and The Hubble Heritage Team (STScI/AURA) Dying star creates sculpture of gas and dust The so-called Cat's Eye Nebula, formally catalogued NGC 6543 and seen here in this detailed view from the NASA/ESA Hubble Space Telescope, is one of the most complex planetary nebulae ever seen in space. A planetary nebula forms when Sun-like stars gently eject their outer gaseous layers to form bright nebulae with amazing twisted shapes. Hubble first revealed NGC 6543's surprisingly intricate structures including concentric gas shells, jets of high-speed gas and unusual shock-induced knots of gas in 1994. This new image, taken with Hubble's Advanced Camera for Surveys (ACS), reveals the full beauty of a bull's-eye pattern of eleven or more concentric rings, or shells, around the Cat’s Eye. Each ‘ring’ is actually the edge of a spherical bubble seen projected onto the sky - which is why it appears bright along its outer edge. High resolution version (JPG format) 125 Kb High resolution version (TIFF format) 2569 Kb Acknowledgment: R. Corradi (Isaac Newton Group of Telescopes, Spain) and Z. Tsvetanov (NASA). Sculpture of gas and dust hi-res Size hi-res: 287 Kb Credits: Nordic Optical Telescope and Romano Corradi (Isaac Newton Group of Telescopes, Spain) Dying star creates sculpture of gas and dust An enormous but extremely faint halo of gaseous material surrounds the Cat’s Eye Nebula and is over three light-years across. Some planetary nebulae been found to have halos like this one, likely formed of material ejected during earlier active episodes in the star's evolution - most likely some 50 000 to 90 000 years ago. This image was taken by Romano Corradi with the Nordic Optical Telescope on La Palma in the Canary Islands. The image is constructed from two narrow-band exposures showing oxygen atoms (1800 seconds, in blue) and nitrogen atoms (1800 seconds, in red). High resolution version (JPG

Modellierung des Einflusses der Landnutzung auf die Hochwasserentstehung in der Mesoskala

NASA Astrophysics Data System (ADS)

Niehoff, Daniel

2001-10-01

Landnutzung dementsprechend größer als in großen Flussgebieten wie dem Rheingebiet, wo vor allem langanhaltende advektive Ereignisse (unter Umständen verbunden mit Schneeschmelze) relevant sind. (3) In Gebieten mit guten Speichereigenschaften wie mächtigen, gut durchlässigen Böden und gut durchlässigem Gesteinsuntergrund ist der Einfluss der Landnutzung größer als in Gebieten mit geringmächtigen Böden und geringdurchlässigem Festgestein. Dies ist darin begründet, dass in Gebieten mit guten Speichereigenschaften bei einer Verschlechterung der Infiltrationsbedingungen mehr Speicherraum für Niederschlag verloren geht als in anderen Gebieten. Since 1990, several of the large European river basins were affected repeatedly by extreme floods. As both the landscape and the river systems in large parts of Central Europe have undergone major changes in the past, during the search for the causes of this accumulation of extreme events also the impact of human activities on flooding has been discussed. River training, surface sealing, intensive agricultural land-use, consolidation of farmland, and damages to forests are only some examples and consequences of the anthropogenic interferences with the landscape. But due to the diversity of the processes and factors involved, by now it can only be estimated how far the flood situation has changed by these interferences. Therefore, the main target of this thesis is to describe systematically in which way, to what extent and under which circumstances the land-use exerts an influence on storm-runoff generation and subsequently the discharge of rivers. This is investigated by means of exemplary model applications at the hydrological meso-scale. For this task, the deterministic and distributed hydrological model wasim-eth was chosen due to its well-balanced mixture of physically-based and conceptual approaches. In the framework of this thesis, the model has been extended in order to cope with several phenomena which are important

Dying Is Unexpectedly Positive.

PubMed

Goranson, Amelia; Ritter, Ryan S; Waytz, Adam; Norton, Michael I; Gray, Kurt

2017-07-01

In people's imagination, dying seems dreadful; however, these perceptions may not reflect reality. In two studies, we compared the affective experience of people facing imminent death with that of people imagining imminent death. Study 1 revealed that blog posts of near-death patients with cancer and amyotrophic lateral sclerosis were more positive and less negative than the simulated blog posts of nonpatients-and also that the patients' blog posts became more positive as death neared. Study 2 revealed that the last words of death-row inmates were more positive and less negative than the simulated last words of noninmates-and also that these last words were less negative than poetry written by death-row inmates. Together, these results suggest that the experience of dying-even because of terminal illness or execution-may be more pleasant than one imagines.

The Unexplored Domains of the s-Process

NASA Astrophysics Data System (ADS)

Roederer, Ian

2016-10-01

Understanding the origin of the elements is one of the major challenges of modern astrophysics. Abundance measurements in late-type stars are used to test nucleosynthesis models, and the models in turn reveal the nature of the progenitor star(s) that produced the metals observed today. Elements listed along the bottom two-thirds of the periodic table are produced by neutron-capture reactions, such as the r-process or s-process. Previous studies have expanded the chemical inventory of individual r-process-enhanced stars to >50 elements per star. Here, we propose to do the same for an s-process-enhanced star.We propose new high-resolution STIS/E230H observations (2024-2301 Angstroms) of the star HD 196944, the UV-brightest s-process-enhanced metal-poor star in the sky. Lines of Se I, Mo II, Cd I, Cd II, Sn I, Sb I, Te I, Yb II, W II, Re II, Os II, Pt I, Pb II, and Bi I should be detectable in these observations because of the high spectral resolution and S/N. No star offers the opportunity to simultaneously detect all of these elements, and several of them could be detected for the first time. We will combine these NUV detections with optical detections to test many specific predictions of the s-process nucleosynthesis models in a way that has not been possible until now. This is particularly timely, for example, because s-process models have recently been shown to be uncertain at the termination point around Pb-Bi.

Cost analysis of medical assistance in dying in Canada.

PubMed

Trachtenberg, Aaron J; Manns, Braden

2017-01-23

The legalization of medical assistance in dying will affect health care spending in Canada. Our aim was to determine the potential costs and savings associated with the implementation of medical assistance in dying. Using published data from the Netherlands and Belgium, where medically assisted death is legal, we estimated that medical assistance in dying will account for 1%-4% of all deaths; 80% of patients will have cancer; 50% of patients will be aged 60-80 years; 55% will be men; 60% of patients will have their lives shortened by 1 month; and 40% of patients will have their lives shortened by 1 week. We combined current mortality data for the Canadian population with recent end-of-life cost data to calculate a predicted range of savings associated with the implementation of medical assistance in dying. We also estimated the direct costs associated with offering medically assisted death, including physician consultations and drug costs. Medical assistance in dying could reduce annual health care spending across Canada by between $34.7 million and $138.8 million, exceeding the $1.5-$14.8 million in direct costs associated with its implementation. In sensitivity analyses, we noted that even if the potential savings are overestimated and costs underestimated, the implementation of mdedical assistance in dying will likely remain at least cost neutral. Providing medical assistance in dying in Canada should not result in any excess financial burden to the health care system, and could result in substantial savings. Additional data on patients who choose medical assistance in dying in Canada should be collected to enable more precise estimates of the impact of medically assisted death on health care spending and to enable further economic evaluation. © 2017 Canadian Medical Association or its licensors.

A Contextualist Thanatology: A Pragmatic Approach to Death and Dying

ERIC Educational Resources Information Center

Reck, Andrew J.

1977-01-01

Denying the value of death but accepting its reality, the author points to dying, not death, as the problematic phenomenon with which a pragmatist thanatology must deal. It is suggested that dying contains opportunities for growth--for the dying as well as for their surviving friends and relatives. (Author)

Herbivory Drives the Spread of Salt Marsh Die-Off

PubMed Central

Bertness, Mark D.; Brisson, Caitlin P.; Bevil, Matthew C.; Crotty, Sinead M.

2014-01-01

Salt marsh die-off is a Western Atlantic conservation problem that has recently spread into Narragansett Bay, Rhode Island, USA. It has been hypothesized to be driven by: 1) eutrophication decreasing plant investment into belowground biomass causing plant collapse, 2) boat wakes eroding creek banks, 3) pollution or disease affecting plant health, 4) substrate hardness controlling herbivorous crab distributions and 5) trophic dysfunction releasing herbivorous crabs from predator control. To distinguish between these hypotheses we quantified these variables at 14 Narragansett Bay salt marshes where die-off intensity ranged from <5% to nearly 98%. Nitrogen availability, wave intensity and plant growth did not explain any variation in die-off. Herbivory explained 73% of inter-site variation in die-off and predator control of herbivores and substrate hardness also varied significantly with die-off. This suggests that salt marsh die-off is being largely driven by intense herbivory via the release of herbivorous crabs from predator control. Our results and those from other marsh systems suggest that consumer control may not simply be a factor to consider in marsh conservation, but with widespread predator depletion impacting near shore habitats globally, trophic dysfunction and runaway consumption may be the largest and most urgent management challenge for salt marsh conservation. PMID:24651837

XML-basierte Produkt- und Prozessdaten für die Leittechnik-Projektierung

NASA Astrophysics Data System (ADS)

Schleipen, Miriam

Für die Überwachung und Steuerung hochkomplexer Produktionsprozesse werden Prozessleitsysteme eingesetzt. Ständige Veränderungen zwingen Produktionsbetriebe wandlungsfähig zu sein. Entsprechend muss auch die Technik diese Flexibilität unterstützen. Jede Veränderung des Produktionsprozesses muss eingeplant, die Anlagen neu konfiguriert und projektiert werden. Dabei müssen auch neue Prozessbilder für die Bedien- und Steuerungssysteme erstellt werden. Am Fraunhofer IITB wurde ein Engineering-Framework entwickelt, das das Leitsystem automatisch projektiert und die zugehörige Prozessvisualisierung generiert. In diesem Beitrag wird das Modul vorgestellt, dass die Prozessabbilder erstellt. Neben der Visualisierung von Anlagen werden auch laufende Prozesse und bearbeitete Produkte dargestellt. So können beispielsweise Identsysteme mit der Leittechnik gekoppelt werden.

Solid state recycling of aluminium alloys via a porthole die hot extrusion process: Scaling up to production

NASA Astrophysics Data System (ADS)

Paraskevas, Dimos; Kellens, Karel; Deng, Yelin; Dewulf, Wim; Kampen, Carlos; Duflou, Joost R.

2017-10-01

Whereas industrial symbiosis has led to increased energy and resource efficiency in process industries, this concept has not yet been applied in discrete product manufacturing. Metal scrap is first conventionally recycled, for which substantial energy and resource efficiency losses have been reported. Recent research has however proven the feasibility of `meltless' recycling of light metal scrap, yielding a first glimpse of potential industrial symbiosis. Various solid state recycling techniques (such as recycling via hot extrusion or Spark Plasma Sintering) have been proposed for scrap consolidation directly into bulk products or semis by physical disruption and dispersion of the oxide surface film by imposing significant plastic and shear strain. Solid State Recycling (SSR) methods can omit substantial material losses as they bypass the metallurgical recycling step. In this context the case of direct production of bulk aluminium profiles via hot extrusion at industrial scale is demonstrated within this paper. The extrusion tests were performed directly into the production line, highlighting the scaling up potentials and the industrial relevance of this research. A significant amount of machining chips were collected, chemically cleaned and cold compacted into chip based billets with ˜80% relative density. Afterwards the scrap consolidation was achieved by imposing significant plastic and shear deformation into the material during hot extrusion through a modified 2-porthole extrusion die-set. The production process sequence along with microstructural investigations and mechanical properties comparison of the cast based profile used as reference versus the chip based profile are presented.

The Conjugation-Specific Die5 Protein Is Required for Development of the Somatic Nucleus in both Paramecium and Tetrahymena▿

PubMed Central

Matsuda, Atsushi; Shieh, Annie Wan-Yi; Chalker, Douglas L.; Forney, James D.

2010-01-01

Development in ciliated protozoa involves extensive genome reorganization within differentiating macronuclei, which shapes the somatic genome of the next vegetative generation. Major events of macronuclear differentiation include excision of internal eliminated sequences (IESs), chromosome fragmentation, and genome amplification. Proteins required for these events include those with homology throughout eukaryotes as well as proteins apparently unique to ciliates. In this study, we identified the ciliate-specific Defective in IES Excision 5 (DIE5) genes of Paramecium tetraurelia (PtDIE5) and Tetrahymena thermophila (TtDIE5) as orthologs that encode nuclear proteins expressed exclusively during development. Abrogation of PtDie5 protein (PtDie5p) function by RNA interference (RNAi)-mediated silencing or TtDie5p by gene disruption resulted in the failure of developing macronuclei to differentiate into new somatic nuclei. Tetrahymena ΔDIE5 cells arrested late in development and failed to complete genome amplification, whereas RNAi-treated Paramecium cells highly amplified new macronuclear DNA before the failure in differentiation, findings that highlight clear differences in the biology of these distantly related species. Nevertheless, IES excision and chromosome fragmentation failed to occur in either ciliate, which strongly supports that Die5p is a critical player in these processes. In Tetrahymena, loss of zygotic expression during development was sufficient to block nuclear differentiation. This observation, together with the finding that knockdown of Die5p in Paramecium still allows genome amplification, indicates that this protein acts late in macronuclear development. Even though DNA rearrangements in these two ciliates look to be quite distinct, analysis of DIE5 establishes the action of a conserved mechanism within the genome reorganization pathway. PMID:20495055

The conjugation-specific Die5 protein is required for development of the somatic nucleus in both Paramecium and Tetrahymena.

PubMed

Matsuda, Atsushi; Shieh, Annie Wan-Yi; Chalker, Douglas L; Forney, James D

2010-07-01

Development in ciliated protozoa involves extensive genome reorganization within differentiating macronuclei, which shapes the somatic genome of the next vegetative generation. Major events of macronuclear differentiation include excision of internal eliminated sequences (IESs), chromosome fragmentation, and genome amplification. Proteins required for these events include those with homology throughout eukaryotes as well as proteins apparently unique to ciliates. In this study, we identified the ciliate-specific Defective in IES Excision 5 (DIE5) genes of Paramecium tetraurelia (PtDIE5) and Tetrahymena thermophila (TtDIE5) as orthologs that encode nuclear proteins expressed exclusively during development. Abrogation of PtDie5 protein (PtDie5p) function by RNA interference (RNAi)-mediated silencing or TtDie5p by gene disruption resulted in the failure of developing macronuclei to differentiate into new somatic nuclei. Tetrahymena DeltaDIE5 cells arrested late in development and failed to complete genome amplification, whereas RNAi-treated Paramecium cells highly amplified new macronuclear DNA before the failure in differentiation, findings that highlight clear differences in the biology of these distantly related species. Nevertheless, IES excision and chromosome fragmentation failed to occur in either ciliate, which strongly supports that Die5p is a critical player in these processes. In Tetrahymena, loss of zygotic expression during development was sufficient to block nuclear differentiation. This observation, together with the finding that knockdown of Die5p in Paramecium still allows genome amplification, indicates that this protein acts late in macronuclear development. Even though DNA rearrangements in these two ciliates look to be quite distinct, analysis of DIE5 establishes the action of a conserved mechanism within the genome reorganization pathway.

Aruna Shanbaug and the right to die with dignity: the battle continues.

PubMed

Kishore, R R

2016-01-01

Aruna Shanbaug's protracted continuance in a persistent vegetative state (PVS) for nearly 42 years needs to be viewed seriously by all those who believe in a person's inalienable right to dignity in dying. A terminally ill and/or incapacitated individual is a helpless person confronted with perpetual risk of intrusion in to his autonomy by the moral paternalists, owing to false notion of human virtues. Legislative inadequacy coupled with judicial heterogeneity has exposed the decision making process to unwarranted ambiguity. Misapplication of moral and juristic principles is a global challenge. 29-year-old Brittany Maynard's recent act of ending her life by migrating from California to Oregon has ignited a fierce debate and nearly half of the states in the USA are contemplating enactment of death with dignity legislation. Across the Atlantic, the European Court of Human Rights judgment on June 5, 2015, endorsing Vincent Lambert's right to end medical support, is a resounding affirmation of an individual's right to die with dignity. This article is an attempt to explore various dimensions of one's right to dignity in dying, in the global as well as the Indian context.

Fatigue properties of die cast zinc alloys for automotive lock applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schrems, Karol K.; Dogan, Omer N.; Goodwin, F.E.

2004-06-01

During the 1970’s many automotive lock systems were converted from zinc die casting alloys to engineering plastics for reasons of weight and cost. Recent increases in requirements for precision and security have caused automotive and other lock designers to reconsider zinc alloy die-castings for these applications. To enable this, there is a need for mechanical property data comparable to that of the plastics materials used in these applications. In this work, rotary bending fatigue tests were performed on Alloys 3, 5, ZA-8 and AcuZinc 5 using an R.R. Moore fatigue machine. Testing was performed at 30 Hz and was stoppedmore » at 1x107 cycles. The fatigue limit results were compared to data reported in the literature for higher number of cycles and faster rotations.« less

Architecture for on-die interconnect

DOEpatents

Khare, Surhud; More, Ankit; Somasekhar, Dinesh; Dunning, David S.

2016-03-15

In an embodiment, an apparatus includes: a plurality of islands configured on a semiconductor die, each of the plurality of islands having a plurality of cores; and a plurality of network switches configured on the semiconductor die and each associated with one of the plurality of islands, where each network switch includes a plurality of output ports, a first set of the output ports are each to couple to the associated network switch of an island via a point-to-point interconnect and a second set of the output ports are each to couple to the associated network switches of a plurality of islands via a point-to-multipoint interconnect. Other embodiments are described and claimed.

Energy-Saving Melting and Revert Reduction Technology (E-SMARRT): Use of Laser Engineered Net Shaping for Rapid Manufacturing of Dies with Protective Coatings and Improved Thermal Management

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brevick, Jerald R.

2014-06-13

In the high pressure die casting process, molten metal is introduced into a die cavity at high pressure and velocity, enabling castings of thin wall section and complex geometry to be obtained. Traditional die materials have been hot work die steels, commonly H13. Manufacture of the dies involves machining the desired geometry from monolithic blocks of annealed tool steel, heat treating to desired hardness and toughness, and final machining, grinding and polishing. The die is fabricated with internal water cooling passages created by drilling. These materials and fabrication methods have been used for many years, however, there are limitations. Toolmore » steels have relatively low thermal conductivity, and as a result, it takes time to remove the heat from the tool steel via the drilled internal water cooling passages. Furthermore, the low thermal conductivity generates large thermal gradients at the die cavity surfaces, which ultimately leads to thermal fatigue cracking on the surfaces of the die steel. The high die surface temperatures also promote the metallurgical bonding of the aluminum casting alloy to the surface of the die steel (soldering). In terms of process efficiency, these tooling limitations reduce the number of die castings that can be made per unit time by increasing cycle time required for cooling, and increasing downtime and cost to replace tooling which has failed either by soldering or by thermal fatigue cracking (heat checking). The objective of this research was to evaluate the feasibility of designing, fabricating, and testing high pressure die casting tooling having properties equivalent to H13 on the surface in contact with molten casting alloy - for high temperature and high velocity molten metal erosion resistance – but with the ability to conduct heat rapidly to interior water cooling passages. A layered bimetallic tool design was selected, and the design evaluated for thermal and mechanical performance via finite element analysis

Thermal Hotspots in CPU Die and It's Future Architecture

NASA Astrophysics Data System (ADS)

Wang, Jian; Hu, Fu-Yuan

Owing to the increasing core frequency and chip integration and the limited die dimension, the power densities in CPU chip have been increasing fastly. The high temperature on chip resulted by power densities threats the processor's performance and chip's reliability. This paper analyzed the thermal hotspots in die and their properties. A new architecture of function units in die - - hot units distributed architecture is suggested to cope with the problems of high power densities for future processor chip.

Thermal Neutron Die-Way-Time Studies for P and DGNAA of Radioactive Waste Drums at the MEDINA Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mildenberger, Frank; Mauerhofer, Eric

2015-07-01

In Germany, radioactive waste with negligible heat production has to pass through a process of quality checking in order to check its conformance with national regulations prior to its transport, intermediate storage and final disposal. Additionally to its radioactive components, the waste may contain non-radioactive chemically toxic substances that can adversely affect human health and pollute the environment, especially the ground water. After an adequate decay time, the waste radioactivity will become harmless but the non-radioactive substances will persist over time. In principle, these hazardous substances may be quantified from traceability and quality controls performed during the production of themore » waste packages. As a consequence, a research and development program was initiated in 2007 with the aim to develop a nondestructive analytical technique for radioactive waste packages based on prompt and delayed gamma neutron activation analysis (P and DGNAA) employing a DT-neutron generator in pulsed mode. In a preliminary study it was experimentally demonstrated that P and DGNAA is suitable to determine the chemical composition of large samples. In 2010 a facility called MEDINA (Multi Element Detection based on Instrumental Neutron Activation) was developed for the qualitative and quantitative determination of nonradioactive, toxic elements and substances in 200-l steel drums. The determination of hazardous substances and elements is generally achieved measuring the prompt gamma-rays induced by thermal neutrons. Additional information about the composition of the waste matrix could be derived measuring the delayed gamma-rays from short life activation products. However a sensitive detection of these delayed gamma-rays requires that thermal neutrons have almost vanished. Therefore, the thermal neutron die-away-time has to be known in order to achieve an optimal discrimination between prompt and delayed gamma-ray spectra acquisition. Measurements Thermal

[Does the right to die with dignity exist?].

PubMed

Toro Flores, Rafael

2008-12-01

Death is one of the few certainties in human beings. This reality generates uneasiness regarding how death will occur especially in circumstances of loneliness or suffering which can become agony. In this report, the author first analyzes the existence of the right to die with dignity as a human right which takes on the nature of being a subjective right. In continuation, the author describes the existing problematic in the application of this right to die in relationship to the so-called double effect mechanism and euthanasia. The author concludes this article by proposing previous instructions or anticipated desires as ideal measures to make the right to die with dignity valid.

Wie die Sonne ins Kraftwerk kommt: Solarthermische Kraftwerke

NASA Astrophysics Data System (ADS)

Pitz-Paal, Robert

2004-01-01

Solarthermische Kraftwerke sammeln wie riesige Brenngläser die Sonnenstrahlung und treiben damit eine Wärmekraftmaschine an. Drei Konstruktionsprinzipien haben sich heute durchgesetzt. Bereits im kommerziellen Einsatz sind Systeme mit schwenkbaren, verspiegelten Parabolrinnen, die das Sonnenlicht auf ein zentrales Absorberrohr konzentrieren. Durch dieses fließt ein Wärmetransportmedium. Beim Zentral-Receiver-System fokussiert ein Feld verstellbarer Spiegel das Sonnenlicht auf die Spitze eines Turms. Dort sitzt ein Receiver, den ein Wärmetransportmedium durchströmt. Für kleine, dezentrale Anlagen eignen sich Dish-Stirling-Systeme. Das sind schwenkbare, paraboloide Spiegelschüsseln mit einem Stirling-Motor im Brennpunkt. Zentral-Receiver- und Dish-Stirling-Systeme sind noch im Entwicklungsstadium.

Die Interhalogenkationen [Br2F5]+ und [Br3F8].

PubMed

Ivlev, Sergei; Karttunen, Antti; Buchner, Magnus; Conrad, Matthias; Kraus, Florian

2018-05-02

Wir berichten über die Synthese und Charakterisierung der bislang einzigen Polyhalogenkationen, in denen verbrückende Fluoratome vorliegen. Das [Br2F5]+-Kation enthält eine symmetrische [F2Br-µ-F-BrF2]-Brücke, das [Br3F8]+-Kation enthält unsymmetrische µ-F-Brücken. Die Fluoronium-Ionen wurden in Form ihrer [SbF6]--Salze erhalten und Raman-, und 19F-NMR-spektroskopisch, sowie durch Röntgenbeugung am Einkristall untersucht. Quantenchemische Rechnungen, sowohl für die isolierten Kationen in der Gasphase, als auch für die Festkörper selbst, wurden durchgeführt. Populationsanalysen zeigen, dass die µ-F-Atome die am stärksten negativ partialgeladenen Atome der Kationen sind. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Epiphytic lichen diversity on dead and dying conifers under different levels of atmospheric pollution.

PubMed

Hauck, Markus

2005-05-01

Based on literature data, epiphytic lichen abundance was comparably studied in montane woodlands on healthy versus dead or dying conifers of Europe and North America in areas with different levels of atmospheric pollution. Study sites comprised Picea abies forests in the Harz Mountains and in the northern Alps, Germany, Picea rubens-Abies balsamea forests on Whiteface Mountain, Adirondacks, New York, U.S.A. and Picea engelmannii-Abies lasiocarpa forests in the Salish Mountains, Montana, U.S.A. Detrended correspondence analysis showed that epiphytic lichen vegetation differed more between healthy and dead or dying trees at high- versus low-polluted sites. This is attributed to greater differences in chemical habitat conditions between trees of different vitality in highly polluted areas. Based on these results, a hypothetical model of relative importance of site factors for small-scale variation of epiphytic lichen abundance versus atmospheric pollutant load is discussed.

Continental-scale consequences of tree die-offs in North America: identifying where forest loss matters most

NASA Astrophysics Data System (ADS)

Swann, Abigail L. S.; Laguë, Marysa M.; Garcia, Elizabeth S.; Field, Jason P.; Breshears, David D.; Moore, David J. P.; Saleska, Scott R.; Stark, Scott C.; Villegas, Juan Camilo; Law, Darin J.; Minor, David M.

2018-05-01

Regional-scale tree die-off events driven by drought and warming and associated pests and pathogens have occurred recently on all forested continents and are projected to increase in frequency and extent with future warming. Within areas where tree mortality has occurred, ecological, hydrological and meteorological consequences are increasingly being documented. However, the potential for tree die-off to impact vegetation processes and related carbon dynamics in areas remote to where die-off occurs has rarely been systematically evaluated, particularly for multiple distinct regions within a given continent. Such remote impacts can occur when climate effects of local vegetation change are propagated by atmospheric circulation—the phenomena of ‘ecoclimate teleconnections’. We simulated tree die-off events in the 13 most densely forested US regions (selected from the 20 US National Ecological Observatory Network [NEON] domains) and found that tree die-off even for smaller regions has potential to affect climate and hence Gross Primary Productivity (GPP) in disparate regions (NEON domains), either positively or negatively. Some regions exhibited strong teleconnections to several others, and some regions were relatively sensitive to tree loss regardless of what other region the tree loss occurred in. For the US as a whole, loss of trees in the Pacific Southwest—an area undergoing rapid tree die-off—had the largest negative impact on remote US GPP whereas loss of trees in the Mid-Atlantic had the largest positive impact. This research lays a foundation for hypotheses that identify how the effects of tree die-off (or other types of tree loss such as deforestation) can ricochet across regions by revealing hot-spots of forcing and response. Such modes of connectivity have direct applicability for improving models of climate change impacts and for developing more informed and coordinated carbon accounting across regions.

Cause and place of death in patients dying with colorectal cancer.

PubMed

Jones, O M; John, S K P; Horseman, N; Lawrance, R J; Fozard, J B J

2007-03-01

Few studies on colorectal cancer look at the one-third of patients for whom treatment fails and who need a management strategy for death. This paper has examined the mode and place of death in patients with colorectal cancer. This study was a review of 209 deaths, analysed between January 2001 and September 2004 by retrospective review of a prospectively collected database. A total of 118 patients (group 1) had undergone resection of their primary colorectal cancer, 20 (group 2) had had a defunctioning stoma or bypass surgery and the remaining 71 patients (group 3) had either had no surgery, an open and close laparotomy or had a colonic stent. One hundred and fifty-six (75%) patients died of colorectal cancer with the remainder dying of other causes. The number of admissions to hospital and the number of days spent in hospital from diagnosis to death were greatest in group 1. Overall, only 34 patients (22%) dying from colorectal cancer died at home. Forty (26%) died in hospital and 70 (45%) died in a palliative care unit. Patients dying from colorectal cancer who undergo surgical resection of their primary tumour spend more time between diagnosis and death in hospital. They are also more likely to die in hospital than patients treated by surgical palliation or nonsurgically. Patients who are treated palliatively from the outset (group 3) are most likely to die at home. If hospital is accepted as an appropriate place for death from colorectal cancer, then greater provision for this should be made.

The narrative labyrinth of violent dying.

PubMed

Rynearson, E K

2005-05-01

This essay outlines the dynamics of retelling the violent death of a loved one and the narrative "dilemma" of vulnerable family members fixated on retelling. To counter this fixation, the author presents a mythic retelling of violent death (the Myth of Theseus) as narrative basis for developing a restorative retelling. The essay begins by exploring the deformed and deforming structure of the violent dying story, then details the dynamics of its retelling and concludes by presenting a restorative retelling model for family members who cannot release themselves from the story for months or years after the violent dying.

Uncovering the decision-making work of transferring dying patients home from critical care units: An integrative review.

PubMed

Lin, Yanxia; Myall, Michelle; Jarrett, Nikki

2017-12-01

To understand how decisions are made to transfer dying patients home from critical care units. Many people prefer a home death, but a high proportion die in critical care units. Transferring dying patients home is recognized to be complex but transfer decision-making itself remains unclear. Integrative review. Seven bibliographic databases (origin-2015), grey literature and reference lists were searched. An integrative review method was used to synthesize data from diverse sources. Papers were selected through title and abstract screening and full-text reviewing, using inclusion and exclusion criteria derived from review questions. Following quality appraisal, data were extracted and synthesized using normalization process theory as a framework. The number of patients transferred home ranged from 1-346, with most papers reporting on the transfer of one or two patients. Four themes regarding transfer decision-making work were generated: divergent views and practice, multiple stakeholders' involvement in decision-making, collective work and limited understanding of individuals' experiences. The practice of transferring patients home to die and its decision-making varies internationally and is usually influenced by the care system, culture or religion. It is less common to transfer patients home to die from critical care units in western societies. A better understanding of the decision-making work was obtained but mainly from the perspective of hospital-based healthcare professionals. Further research is needed to develop decision-making practice guidance to facilitate patients' wishes to die at home. © 2017 John Wiley & Sons Ltd.

Die Grundlagen der Fernsehtechnik: Systemtheorie und Technik der Bildübertragung

NASA Astrophysics Data System (ADS)

Mahler, Gerhard

Umfassende Einführung in die Grundlagen der Bewegtbild-Übertragung von den Anfängen bis zum heutigen Stand des digitalen Fernsehens mit einer aus der Praxis entstandenen systemtheoretischen Analyse. Die kompakte und anschaulich bebilderte Darstellung mit elementaren mathematischen Beschreibungen macht es dem Leser leicht, sich in die Bildübertragungstechnik einzuarbeiten. Thematische Einheiten erweitern den Wissensstoff - u.a. zu den Themen visuelle Wahrnehmung, mehrdimensionale Signaldarstellung, Farbmetrik, Digitalisierung, Elektronenoptik - und zeigen deren Anwendung auf die elektronische Bildübertragung.

Milling strategies evaluation when simulating the forming dies' functional surfaces production

NASA Astrophysics Data System (ADS)

Ižol, Peter; Tomáš, Miroslav; Beňo, Jozef

2016-05-01

The paper deals with selection and evaluation of milling strategies, available in CAM systems and applicable when complicated shape parts are produced, such as forming dies. A method to obtain samples is proposed and this stems from real forming die surface machined by proper strategies. The strategy applicability for the whole part - forming die - is reviewed by the particular specimen evaluation. The presented methodology has been verified by machining model die and comparing it to the production procedure proposed in other CAM systems.

The right to be allowed to die.

PubMed Central

Campbell, A G

1983-01-01

The unbridled use of modern medical skills and technology in preserving life at all costs has stimulated interest in expressing a 'right to die' by the legally competent patient who is anxious to protect his autonomy. Some recent decisions by American courts are seen to threaten this 'right to die' of competent patients and imply that legally incompetent patients including children should not have this right under any circumstances, even when expressed on their behalf by guardians, nearest relatives or parents. It is argued that this is contrary to 'natural justice' as viewed by most people. It should be possible to develop procedures which are protective of the basic 'right to life' of the incompetent yet will recognise circumstances where they could be allowed to die. This paper was presented at the 1983 annual conference of the London Medical Group, 'Human Rights in Medicine'. PMID:6620316

Water-quality impacts from climate-induced forest die-off

NASA Astrophysics Data System (ADS)

Mikkelson, Kristin M.; Dickenson, Eric R. V.; Maxwell, Reed M.; McCray, John E.; Sharp, Jonathan O.

2013-03-01

Increased ecosystem susceptibility to pests and other stressors has been attributed to climate change, resulting in unprecedented tree mortality from insect infestations. In turn, large-scale tree die-off alters physical and biogeochemical processes, such as organic matter decay and hydrologic flow paths, that could enhance leaching of natural organic matter to soil and surface waters and increase potential formation of harmful drinking water disinfection by-products (DBPs). Whereas previous studies have investigated water-quantity alterations due to climate-induced, forest die-off, impacts on water quality are unclear. Here, water-quality data sets from water-treatment facilities in Colorado were analysed to determine whether the municipal water supply has been perturbed by tree mortality. Results demonstrate higher total organic carbon concentrations along with significantly more DBPs at water-treatment facilities using mountain-pine-beetle-infested source waters when contrasted with those using water from control watersheds. In addition to this differentiation between watersheds, DBP concentrations demonstrated an increase within mountain pine beetle watersheds related to the degree of infestation. Disproportionate DBP increases and seasonal decoupling of peak DBP and total organic carbon concentrations further suggest that the total organic carbon composition is being altered in these systems.

Measuring death-related anxiety in advanced cancer: preliminary psychometrics of the Death and Dying Distress Scale.

PubMed

Lo, Christopher; Hales, Sarah; Zimmermann, Camilla; Gagliese, Lucia; Rydall, Anne; Rodin, Gary

2011-10-01

The alleviation of distress associated with death and dying is a central goal of palliative care, despite the lack of routine measurement of this outcome. In this study, we introduce the Death and Dying Distress Scale (DADDS), a new, brief measure we have developed to assess death-related anxiety in advanced cancer and other palliative populations. We describe its preliminary psychometrics based on a sample of 33 patients with advanced or metastatic cancer. The DADDS broadly captures distress about the loss of time and opportunity, the process of death and dying, and its impact on others. The initial version of the scale has a one-factor structure and good internal reliability. Dying and death-related distress was positively associated with depression and negatively associated with spiritual, emotional, physical, and functional well-being, providing early evidence of construct validity. This distress was relatively common, with 45% of the sample scoring in the upper reaches of the scale, suggesting that the DADDS may be a relevant outcome for palliative intervention. We conclude by presenting a revised 15-item version of the scale for further study in advanced cancer and other palliative populations.

Dying in hospital: socioeconomic inequality trends in England

PubMed Central

Asaria, Miqdad; Sheringham, Jessica; Stone, Patrick; Raine, Rosalind; Cookson, Richard

2017-01-01

Objective To describe trends in socioeconomic inequality in the proportion of deaths occurring in hospital, during a period of sustained effort by the NHS in England to improve end of life care. Methods Whole-population, small area longitudinal study involving 5,260,871 patients of all ages who died in England from 2001/2002 to 2011/2012. Our primary measure of inequality was the slope index of inequality. This represents the estimated gap between the most and least deprived neighbourhood in England, allowing for the gradient in between. Neighbourhoods were geographic Lower Layer Super Output Areas containing about 1500 people each. Results The overall proportion of patients dying in hospital decreased from 49.5% to 43.6% during the study period, after initially increasing to 52.0% in 2004/2005. There was substantial ‘pro-rich’ inequality, with an estimated difference of 5.95 percentage points in the proportion of people dying in hospital (confidence interval 5.26 to 6.63), comparing the most and least deprived neighbourhoods in 2011/2012. There was no significant reduction in this gap over time, either in absolute terms or relative to the mean, despite the overall reduction in the proportion of patients dying in hospital. Conclusions Efforts to reduce the proportion of patients dying in hospital in England have been successful overall but did not reduce inequality. Greater understanding of the reasons for such inequality is required before policy changes can be determined. PMID:28429981

The Relationship between Dendrite Arm Spacing and Cooling Rate of Al-Si Casting Alloys in High Pressure Die Casting

NASA Astrophysics Data System (ADS)

Cho, Jae-Ik; Kim, Cheol-Woo; Kim, Young-Chan; Choi, Se-Weon; Kang, Chang-Seog

The effects of cooling rate on the solidification behavior of Al-8.5%Si-3%Cu and Al-11%Si-3%Cu alloys were studied during high pressure die casting (HPDC). The HPDC experiment was conducted by using the dies with 3 steps for 3 different cooling rates. Because of the high in both melt temperature and pressure, it was difficult to obtain the temperature profile directly from HPDC specimen. Therefore, in this study, cylindrical bar castings with different diameter were poured to acquire the cooling curves at the solidification range of 15°C/s up to 100°C/s and then the microstructures were compared to estimate the cooling rate in HPDC. The solidification characteristics including liquidus/solidus temperature and dendrite arm spacing of each alloy and each cooling rate was analyzed and the results showed strong proportional relationship between dendrite arm spacing and cooling rate in HPDC. The results were also compared with the actual die casting specimens and MAGMA simulation.

Christopher Hitchens' Public Dying: Toward a Secular-Humanist Ars Moriendi?

PubMed

Brennan, Michael

2018-06-01

This article explores the public dying of journalist, writer, provocateur, public intellectual, and renowned atheist, Christopher Hitchens. It does so primarily through an analysis of television interviews given by Hitchens following his diagnosis with esophageal cancer in June 2010. Four key themes are identified as emerging from analysis of the interviews: (a) Hitchens' explicit sense of mission in challenging myths and superstitions surrounding cancer, dying, and death; (b) the personal experience of terminal illness and dying and the particular way (or style of dying) by which it is approached; (c) issues of regret and a life well lived; and (d) questions surrounding religion, the afterlife, and possibility of deathbed conversion. In light of the claim that ours is a culture in search of an ars moriendi, the article examines what we can learn from Hitchens' auto/pathographic interviews (and writings) and the extent to which this rational-humanist, atheistic, and stoical style of dying provides a useable "template" for others nearing the end of life.

Oncology Nursing Education: Nursing Students' Commitment of "Presence" with the Dying Patient and the Family.

ERIC Educational Resources Information Center

Walsh, Sandra M.; Hogan, Nancy S.

2003-01-01

Following a chaplain's lecture on the end of life, nursing students wrote reaction papers on appropriate ways to support dying patients and their families. Six processes emerged, including the core concept of the nurse's presence at the bedside. (Contains 23 references.) (SK)

Auditory spatial processing in Alzheimer’s disease

PubMed Central

Golden, Hannah L.; Nicholas, Jennifer M.; Yong, Keir X. X.; Downey, Laura E.; Schott, Jonathan M.; Mummery, Catherine J.; Crutch, Sebastian J.

2015-01-01

The location and motion of sounds in space are important cues for encoding the auditory world. Spatial processing is a core component of auditory scene analysis, a cognitively demanding function that is vulnerable in Alzheimer’s disease. Here we designed a novel neuropsychological battery based on a virtual space paradigm to assess auditory spatial processing in patient cohorts with clinically typical Alzheimer’s disease (n = 20) and its major variant syndrome, posterior cortical atrophy (n = 12) in relation to healthy older controls (n = 26). We assessed three dimensions of auditory spatial function: externalized versus non-externalized sound discrimination, moving versus stationary sound discrimination and stationary auditory spatial position discrimination, together with non-spatial auditory and visual spatial control tasks. Neuroanatomical correlates of auditory spatial processing were assessed using voxel-based morphometry. Relative to healthy older controls, both patient groups exhibited impairments in detection of auditory motion, and stationary sound position discrimination. The posterior cortical atrophy group showed greater impairment for auditory motion processing and the processing of a non-spatial control complex auditory property (timbre) than the typical Alzheimer’s disease group. Voxel-based morphometry in the patient cohort revealed grey matter correlates of auditory motion detection and spatial position discrimination in right inferior parietal cortex and precuneus, respectively. These findings delineate auditory spatial processing deficits in typical and posterior Alzheimer’s disease phenotypes that are related to posterior cortical regions involved in both syndromic variants and modulated by the syndromic profile of brain degeneration. Auditory spatial deficits contribute to impaired spatial awareness in Alzheimer’s disease and may constitute a novel perceptual model for probing brain network disintegration across the Alzheimer’s

[Right to die with dignity?].

PubMed

Ruiz, Alvaro

2008-06-01

The right to die with dignity is an ill-defined concept, with multiple, often inappropriate, interpretations. The current proposition is that the physician take full responsibility for protecting the patients rights, for ensuring a rational use of resources and for overseeing the decision-making process such that the information is adequate and the steps proportioned. This responsibility extends not only to the health status of the patient situation, to the patients prognosis, and to his/her expectations and wishes, but also to the benefits foreseen and to the cost-benefit ratio. Emphasis is placed on two aspects of this relationship. First, dignity can be interpreted in many ways and sometimes, in the name of dignity, the patient is exposed (or exposes him/herself) to suffering, pain and complications that can be avoided. Second, when no reasonable probability of survival is present and a better quality of life is impossible, efforts are better redirected to offering a better quality of death.

Tribological and Wear Performance of Nanocomposite PVD Hard Coatings Deposited on Aluminum Die Casting Tool

PubMed Central

Fox-Rabinovich, German; Locks Junior, Edinei; Stolf, Pietro; Matos Martins, Marcelo

2018-01-01

In the aluminum die casting process, erosion, corrosion, soldering, and die sticking have a significant influence on tool life and product quality. A number of coatings such as TiN, CrN, and (Cr,Al)N deposited by physical vapor deposition (PVD) have been employed to act as protective coatings due to their high hardness and chemical stability. In this study, the wear performance of two nanocomposite AlTiN and AlCrN coatings with different structures were evaluated. These coatings were deposited on aluminum die casting mold tool substrates (AISI H13 hot work steel) by PVD using pulsed cathodic arc evaporation, equipped with three lateral arc-rotating cathodes (LARC) and one central rotating cathode (CERC). The research was performed in two stages: in the first stage, the outlined coatings were characterized regarding their chemical composition, morphology, and structure using glow discharge optical emission spectroscopy (GDOES), scanning electron microscopy (SEM), and X-ray diffraction (XRD), respectively. Surface morphology and mechanical properties were evaluated by atomic force microscopy (AFM) and nanoindentation. The coating adhesion was studied using Mersedes test and scratch testing. During the second stage, industrial tests were carried out for coated die casting molds. In parallel, tribological tests were also performed in order to determine if a correlation between laboratory and industrial tests can be drawn. All of the results were compared with a benchmark monolayer AlCrN coating. The data obtained show that the best performance was achieved for the AlCrN/Si3N4 nanocomposite coating that displays an optimum combination of hardness, adhesion, soldering behavior, oxidation resistance, and stress state. These characteristics are essential for improving the die mold service life. Therefore, this coating emerges as a novelty to be used to protect aluminum die casting molds. PMID:29495620

Tribological and Wear Performance of Nanocomposite PVD Hard Coatings Deposited on Aluminum Die Casting Tool.

PubMed

Paiva, Jose Mario; Fox-Rabinovich, German; Locks Junior, Edinei; Stolf, Pietro; Seid Ahmed, Yassmin; Matos Martins, Marcelo; Bork, Carlos; Veldhuis, Stephen

2018-02-28

In the aluminum die casting process, erosion, corrosion, soldering, and die sticking have a significant influence on tool life and product quality. A number of coatings such as TiN, CrN, and (Cr,Al)N deposited by physical vapor deposition (PVD) have been employed to act as protective coatings due to their high hardness and chemical stability. In this study, the wear performance of two nanocomposite AlTiN and AlCrN coatings with different structures were evaluated. These coatings were deposited on aluminum die casting mold tool substrates (AISI H13 hot work steel) by PVD using pulsed cathodic arc evaporation, equipped with three lateral arc-rotating cathodes (LARC) and one central rotating cathode (CERC). The research was performed in two stages: in the first stage, the outlined coatings were characterized regarding their chemical composition, morphology, and structure using glow discharge optical emission spectroscopy (GDOES), scanning electron microscopy (SEM), and X-ray diffraction (XRD), respectively. Surface morphology and mechanical properties were evaluated by atomic force microscopy (AFM) and nanoindentation. The coating adhesion was studied using Mersedes test and scratch testing. During the second stage, industrial tests were carried out for coated die casting molds. In parallel, tribological tests were also performed in order to determine if a correlation between laboratory and industrial tests can be drawn. All of the results were compared with a benchmark monolayer AlCrN coating. The data obtained show that the best performance was achieved for the AlCrN/Si₃N₄ nanocomposite coating that displays an optimum combination of hardness, adhesion, soldering behavior, oxidation resistance, and stress state. These characteristics are essential for improving the die mold service life. Therefore, this coating emerges as a novelty to be used to protect aluminum die casting molds.

Breaking bad news about transitions to dying: a qualitative exploration of the role of the District Nurse.

PubMed

Griffiths, Jane; Ewing, Gail; Wilson, Charlotte; Connolly, Michael; Grande, Gunn

2015-02-01

UK District Nurses have an important role in enabling a good death. Patients and families need to know the patient is approaching the dying phase, yet evidence suggests breaking bad news about the patient's transition to dying rarely happens. District Nurses spend a lot of time with patients and families during the dying phase and are ideally placed to recognise and discuss the transition to dying. To explore the role of District Nurses in breaking bad news of transition to dying. Qualitative focus groups. Primary care (District Nurse service); Four National Health Service Trusts, North West England. A total of 40 District Nurses across the Trusts, all Registered General Nurse qualified. Median number of years as a District Nurse was 12.5. All had palliative cancer patients on their caseloads. District Nurses' role in breaking bad news of transition to dying was challenging, but the conversation was described as essential preparation for a good death. Four main challenges with the conversations were patients' responses to the prognosis (unawareness, denial and anger), timing the conversation, complexities of the home environment and limited preparation in this aspect of their work. District Nurses are with patients during their last weeks of life. While other colleagues can avoid breaking bad news of transition to dying, District Nurses have no choice if they are to provide optimal end of life care. While ideally placed to carry out this work, it is complex and they are unprepared for it. They urgently need carefully tailored training in this aspect of their work, to enable them to provide optimal end of life care. © The Author(s) 2014.

Killing and letting die: hidden value assumptions.

PubMed

Atkinson, G

1983-01-01

In this paper I argue for several related theses: first, that the distinction between killing and letting die, as it is drawn by ordinary persons in ordinary contexts, is more complex than is generally understood; second, that the key feature of this complexity lies in the presence of a hidden normative component in what appears to be a straightforwardly descriptive distinction; and, third, that this complexity renders the killing/letting die distinction an inadequate and hazardous guide for moral reasoning.

The Dying Child: The Management of the Child or Adolescent Who is Dying.

ERIC Educational Resources Information Center

Easson, William M.

Primarily describing the child who must endure a lengthy terminal illness and prolonged period of dying, the text presents the developmental stages of the child's understanding of his own death. Characteristics of the child at various ages (preschool, elementary school, and adolescent) are examined in areas such as hospitalization effects,…

Characterization by X-ray tomography of granulated alumina powder during in situ die compaction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cottrino, Sandrine; Jorand, Yves, E-mail: yves.jorand@insa-lyon.fr; Maire, Eric

2013-07-15

Compaction process, the aim of which being to obtain green bodies with low porosity and small size, is often used before sintering treatment. Prior to die filling, the ceramic powder is generally granulated to improve flowability. However during compaction, density heterogeneity and critical size defects may appear due to intergranule and granule-die wall frictions. In this work, the influence of granule formulation on the compact morphology has been studied. To do so, a compaction setup was installed inside an X-ray tomography equipment so that the evolution of the compact morphology could be analysed during the whole compaction process. We havemore » demonstrated that high humidity rate and the addition of binder in the granule formulation increase density heterogeneity and generate larger defects. - Highlights: • An original compaction set up was installed inside an X-Ray tomography equipment. • The compaction process of granulated ceramic powder is imaged. • The compact green microstructure is quantified and related to the compaction stages. • The most detrimental defects of dry-pressed parts are caused by hollow granules. • Formulations without binder allow a reduction of the number of large defects.« less

Strippable grid facilitates removal of grid-surfaced conical workpiece from die

NASA Technical Reports Server (NTRS)

Ruppe, E. P.

1966-01-01

Female die facilitates the removal of a sheet metal structure from a die used for explosive forming of the metal. The female die consists of a smooth conical frustum made of fiber glass with a cured epoxy-resin surface on which a molded grid pattern made of a polyurethane resin is overlaid.

Setup of a Parameterized FE Model for the Die Roll Prediction in Fine Blanking using Artificial Neural Networks

NASA Astrophysics Data System (ADS)

Stanke, J.; Trauth, D.; Feuerhack, A.; Klocke, F.

2017-09-01

Die roll is a morphological feature of fine blanked sheared edges. The die roll reduces the functional part of the sheared edge. To compensate for the die roll thicker sheet metal strips and secondary machining must be used. However, in order to avoid this, the influence of various fine blanking process parameters on the die roll has been experimentally and numerically studied, but there is still a lack of knowledge on the effects of some factors and especially factor interactions on the die roll. Recent changes in the field of artificial intelligence motivate the hybrid use of the finite element method and artificial neural networks to account for these non-considered parameters. Therefore, a set of simulations using a validated finite element model of fine blanking is firstly used to train an artificial neural network. Then the artificial neural network is trained with thousands of experimental trials. Thus, the objective of this contribution is to develop an artificial neural network that reliably predicts the die roll. Therefore, in this contribution, the setup of a fully parameterized 2D FE model is presented that will be used for batch training of an artificial neural network. The FE model enables an automatic variation of the edge radii of blank punch and die plate, the counter and blank holder force, the sheet metal thickness and part diameter, V-ring height and position, cutting velocity as well as material parameters covered by the Hensel-Spittel model for 16MnCr5 (1.7131, AISI/SAE 5115). The FE model is validated using experimental trails. The results of this contribution is a FE model suitable to perform 9.623 simulations and to pass the simulated die roll width and height automatically to an artificial neural network.

Process for preparing tapes from thermoplastic polymers and carbon fibers

NASA Technical Reports Server (NTRS)

Chung, Tai-Shung (Inventor); Furst, Howard (Inventor); Gurion, Zev (Inventor); McMahon, Paul E. (Inventor); Orwoll, Richard D. (Inventor); Palangio, Daniel (Inventor)

1986-01-01

The instant invention involves a process for use in preparing tapes or rovings, which are formed from a thermoplastic material used to impregnate longitudinally extended bundles of carbon fibers. The process involves the steps of (a) gas spreading a tow of carbon fibers; (b) feeding the spread tow into a crosshead die; (c) impregnating the tow in the die with a thermoplastic polymer; (d) withdrawing the impregnated tow from the die; and (e) gas cooling the impregnated tow with a jet of air. The crosshead die useful in the instant invention includes a horizontally extended, carbon fiber bundle inlet channel, means for providing melted polymer under pressure to the die, means for dividing the polymeric material flowing into the die into an upper flow channel and a lower flow channel disposed above and below the moving carbon fiber bundle, means for applying the thermoplastic material from both the upper and lower channels to the fiber bundle, and means for withdrawing the resulting tape from the die.

Death and Dying Course Offerings in Psychology: A Survey of Nine Midwestern States

ERIC Educational Resources Information Center

Eckerd, Lizabeth M.

2009-01-01

The certainty of facing death and bereavement and the complex personal and societal issues involved argue for the importance of death education. The current study addresses a gap in knowledge by beginning to assess the extent of dying, death, and bereavement (DD&B) course offerings by U.S. psychology departments. This article reports on data…

Home to die from the intensive care unit: A qualitative descriptive study of the family's experience.

PubMed

Hutchinson, Amy L; Van Wissen, Kim A

2017-12-01

Many people would choose to die at home, and this can be an option for intensive care patients. However, there is limited exploration of the impact on the family. To gain insight into family members' experiences when an adult intensive care unit patient is taken home to die. Methodology is qualitative description, utilising purposeful sampling, unstructured interviews and thematic analysis. Four participants, from two different families were interviewed. The setting was a tertiary level Intensive Care Unit in New Zealand. The experience was described as a kaleidoscope of events with two main themes: 'value' family member's found in the patient going home, and their experience of the 'process'. 'Value' subthemes: going home being the patient's own decision, home as an end-of-life environment, and the patient's positive response to being at home. 'Process' subthemes: care and support received, stress of a family member being in intensive care, feeling that everything happened quickly, and concerns and uncertainties. Going home to die from the intensive care unit can be a positive but challenging experience for the family. Full collaboration between the patient, family and staff is essential, to ensure the family are appropriately supported. Copyright © 2017 Elsevier Ltd. All rights reserved.

The fuzzy algorithm in the die casting mould for the application of multi-channel temperature control

NASA Astrophysics Data System (ADS)

Sun, Jin-gen; Chen, Yi; Zhang, Jia-nan

2017-01-01

Mould manufacturing is one of the most basic elements in the production chain of China. The mould manufacturing technology has become an important symbol to measure the level of a country's manufacturing industry. The die-casting mould multichannel intelligent temperature control method is studied by cooling water circulation, which uses fuzzy control to realize, aiming at solving the shortcomings of slow speed and big energy consumption during the cooling process of current die-casting mould. At present, the traditional PID control method is used to control the temperature, but it is difficult to ensure the control precision. While , the fuzzy algorithm is used to realize precise control of mould temperature in cooling process. The design is simple, fast response, strong anti-interference ability and good robustness. Simulation results show that the control method is completely feasible, which has higher control precision.

Assisted suicide by oxygen deprivation with helium at a Swiss right-to-die organisation.

PubMed

Ogden, Russel D; Hamilton, William K; Whitcher, Charles

2010-03-01

In Switzerland, right-to-die organisations assist their members with suicide by lethal drugs, usually barbiturates. One organisation, Dignitas, has experimented with oxygen deprivation as an alternative to sodium pentobarbital. To analyse the process of assisted suicide by oxygen deprivation with helium and a common face mask and reservoir bag. This study examined four cases of assisted suicide by oxygen deprivation using helium delivered via a face mask. Videos of the deaths were provided by the Zurich police. Dignitas provided protocol and consent information. One man and three women were assisted to death by oxygen deprivation. There was wide variation in the time to unconsciousness and the time to death, probably due to the poor mask fit. Swiss law prevented attendants from effectively managing the face mask apparatus. Purposeless movements of the extremities were disconcerting for Dignitas attendants, who are accustomed to assisting suicide with barbiturates. None of the dying individuals attempted self-rescue. The dying process of oxygen deprivation with helium is potentially quick and appears painless. It also bypasses the prescribing role of physicians, effectively demedicalising assisted suicide. Oxygen deprivation with a face mask is not acceptable because leaks are difficult to control and it may not eliminate rebreathing. These factors will extend time to unconsciousness and time to death. A hood method could reduce the problem of mask fit. With a hood, a flow rate of helium sufficient to provide continuous washout of expired gases would remedy problems observed with the mask.

Knowing Kids Dying of HIV: A Traumatic Event for AIDS Orphans

PubMed Central

Zhao, Qun; Li, Xiaoming; Lin, Xiuyun; Fang, Xiaoyi; Zhao, Guoxiang; Zhao, Junfeng

2009-01-01

Data from 755 AIDS orphans living in a rural area of China with high rates of HIV infection were used to examine the association between a child’s trauma symptoms and knowing a peer with HIV infection or one who had died of HIV. Trauma symptoms were measured by the Traumatic Symptoms Checklist for Children-Chinese Version (TSCC-CV). About 47% of participants reported they knew a child with HIV or one who had died of HIV. More orphans living in family-based care reported such knowledge, and trauma symptoms were significantly higher in children who reported such knowledge. Multivariate analysis revealed that such knowledge was significantly associated with traumatic symptoms, controlling for gender, age, family socioeconomic status, orphan status (double vs. single), and care arrangement (family-based vs. institutional care). The findings underscored the importance of psychosocial support and counseling to orphans in communities with high levels of HIV-related mortality. PMID:19576544

Motivations, Satisfaction, and Fears of Death and Dying in Residential Hospice Volunteers: A Prospective Longitudinal Study.

PubMed

Nissim, Rinat; Emmerson, Debbie; O'Neill, Bill; Marchington, Katie; Draper, Haley; Rodin, Gary

2016-05-01

Studies conducted on hospice volunteers' characteristics and experiences have been cross-sectional. We conducted a prospective study to examine changes in the volunteer experience over time in a cohort of volunteers during the first year of a new residential hospice. Eighty-two active volunteers completed an online baseline survey, and of these, 39 completed a follow-up survey at 6 months. The survey included measures of motivations to volunteer, satisfaction with role and with the organization, and fear of death and dying. Repeated measures analyses indicated that motivations to volunteer remained stable over time while volunteer satisfaction increased with time. Baseline level of fears of death and dying varied by age, volunteer role, and motivations to volunteer and decreased at 6 months. Volunteering in a residential hospice tends to be a satisfying experience that helps to allay fears about death and dying. © The Author(s) 2014.

Recent tree die-off has little effect on streamflow in contrast to expected increases from historical studies

NASA Astrophysics Data System (ADS)

Biederman, Joel A.; Somor, Andrew J.; Harpold, Adrian A.; Gutmann, Ethan D.; Breshears, David D.; Troch, Peter A.; Gochis, David J.; Scott, Russell L.; Meddens, Arjan J. H.; Brooks, Paul D.

2015-12-01

Recent bark beetle epidemics have caused regional-scale tree mortality in many snowmelt-dominated headwater catchments of western North America. Initial expectations of increased streamflow have not been supported by observations, and the basin-scale response of annual streamflow is largely unknown. Here we quantified annual streamflow responses during the decade following tree die-off in eight infested catchments in the Colorado River headwaters and one nearby control catchment. We employed three alternative empirical methods: (i) double-mass comparison between impacted and control catchments, (ii) runoff ratio comparison before and after die-off, and (iii) time-trend analysis using climate-driven linear models. In contrast to streamflow increases predicted by historical paired catchment studies and recent modeling, we did not detect streamflow changes in most basins following die-off, while one basin consistently showed decreased streamflow. The three analysis methods produced generally consistent results, with time-trend analysis showing precipitation was the strongest predictor of streamflow variability (R2 = 74-96%). Time-trend analysis revealed post-die-off streamflow decreased in three catchments by 11-29%, with no change in the other five catchments. Although counter to initial expectations, these results are consistent with increased transpiration by surviving vegetation and the growing body of literature documenting increased snow sublimation and evaporation from the subcanopy following die-off in water-limited, snow-dominated forests. The observations presented here challenge the widespread expectation that streamflow will increase following beetle-induced forest die-off and highlight the need to better understand the processes driving hydrologic response to forest disturbance.

Microstructures and properties of aluminum die casting alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

M. M. Makhlouf; D. Apelian; L. Wang

1998-10-01

This document provides descriptions of the microstructure of different aluminum die casting alloys and to relate the various microstructures to the alloy chemistry. It relates the microstructures of the alloys to their main engineering properties such as ultimate tensile strength, yield strength, elongation, fatigue life, impact resistance, wear resistance, hardness, thermal conductivity and electrical conductivity. Finally, it serves as a reference source for aluminum die casting alloys.

Courts to look again at assisted dying law.

PubMed

Griffith, Richard

2017-05-02

A man with motor neurone disease has been granted permission by the Court of Appeal to seek judicial review the criminalisation of assisted dying under the Suicide Act 1961, section 2(1). In this article, Richard Griffith reviews the Court of Appeal's decision in R (on the application of Conway) v Secretary of State for Justice [2017] and considers arguments for and against decriminalising assisted dying.

Morphology and Performance of 5Cr5MoV Casting Die Steel in the Process of Surfacing

NASA Astrophysics Data System (ADS)

Song, Yulai; Kong, Xiangrui; Yang, Pengcong; Fu, Hongde; Wang, Xuezhu

2017-12-01

To investigate the microstructures and mechanical properties of the deposited metal on surface of die steel, two layer of weld-seam were prepared on the surface of 5Cr5MoV die steel by arc surfacing. The surface microstructures and microhardness were characterized by scanning electron microscopy, energy dispersive spectrometer and Vickers microhardness tester, respectively. The effect of load on the abrasion resistance and wear mechanism of the base metal and surfacing metal was studied by pin-on-disk tribometer. The results showed that martensite and retained austenite exist in weld-seam, both of them grow up in the form of dendrites and equiaxed grains and microhardness reach 774.2HV. The microstructures of the quenching zone mainly consist of martensite and retained austenite, while tempered martensite is the dominant phase in partial quenching zone. The abrasion resistance of the surfacing metal is superior to the base metal based on the results of wear test. The wear rates of surfacing metal and base metal raise with the increase of load. The wear rates of base metal raise extremely when the load reach 210N. Both of two kinds of materials have the similar wear mechanism, namely, abrasive wear at low load, oxidative wear and adhesive wear at high load.

High electrical resistivity Nd-Fe-B die-upset magnet doped with eutectic DyF3-LiF salt mixture

NASA Astrophysics Data System (ADS)

Kim, K. M.; Kim, J. Y.; Kwon, H. W.; Kim, D. H.; Lee, J. G.; Yu, J. H.

2017-05-01

Nd-Fe-B-type die-upset magnet with high electrical resistivity was prepared by doping of eutectic DyF3-LiF salt mixture. Mixture of melt-spun Nd-Fe-B flakes (MQU-F: Nd13.6Fe73.6Co6.6Ga0.6B5.6) and eutectic binary (DyF3-LiF) salt (25 mol% DyF3 - 75 mol% LiF) was hot-pressed and then die-upset. By adding the eutectic salt mixture (> 4 wt%), electrical resistivity of the die-upset magnet was enhanced to over 400 μ Ω .cm compared to 190 μ Ω .cm of the un-doped magnet. Remarkable enhancement of the electrical resistivity was attributed to homogeneous and continuous coverage of the interface between flakes by the easily melted eutectic salt dielectric mixture. It was revealed that active substitution of the Nd atoms in neighboring flakes by the Dy atoms from the added (DyF3-LiF) salt mixture had occurred during such a quick thermal processing of hot-pressing and die-upsetting. This Dy substitution led to coercivity enhancement in the die-upset magnet doped with the eutectic (DyF3-LiF) salt mixture. Coercivity and remanence of the die-upset magnet doped with (DyF3-LiF) salt mixture was as good as those of the DyF3-doped magnet.

Von Start-ups lernen - Methoden und Entwicklungsprozesse, die Jungunternehmen erfolgreich machen

NASA Astrophysics Data System (ADS)

Böhme, Eckhart

Die Start-up-Bewegung bringt beständig sog. Disruptoren hervor, die jede Branche betreffen und so gut wie keinen Lebensbereich auslassen. Diese Jungunternehmen, insbesondere aus der Softwarebranche, verfügen zwar nicht über Ressourcen wie etablierte Unternehmen, sie sind jedoch agil, "hungrig", können frei von "Ballast" agieren und treiben die Digitalisierung aller Branchen voran. Aber auch Start-ups können nicht einfach ungetestete Ideen in erfolgreiche Produkte oder Dienstleistungen umwandeln und ihren Erfolg dem Zufall überlassen. Erfolgreiche Jungunternehmen folgen vielmehr einem strukturierten Prozess, um marktgetestete Nutzenversprechen und Geschäftsmodelle zu entwickeln. Zunehmend adaptieren etablierte Unternehmen innovative Entwicklungsprozesse und Methoden. Die Fragestellung für Energieversorgungsunternehmen (EVUs) lautet, welche Methoden, Werkzeuge und Entwicklungsprozesse, die heute bei vielen Start-ups eingesetzt werden, sie aufgreifen können, um das Unternehmen gegenüber Disruptoren robust zu machen?

Quality of dying and death with cancer in Israel.

PubMed

Braun, Michal; Hasson-Ohayon, Ilanit; Hales, Sarah; Zimmermann, Camilla; Rydall, Anne; Peretz, Tamar; Rodin, Gary

2014-07-01

The quality of dying and death refers to the evaluation of the final days of life and the moment of death with respect to how it is prepared for, faced and experienced by those with a terminal illness. It includes experience in multiple domains: physical, psychological, social, spiritual or existential, the nature of health care, life closure and death preparation, and the circumstances of death. To explore the quality of dying and death in cancer patients in Israel and its relationship to place of death and socio-demographic characteristics of the primary caregivers and the deceased. Retrospective assessment of the quality of dying and death, based on caregiver responses to the Quality of Dying and Death (QODD) questionnaire (overall score ranges from 0 to 100; higher scores reflect better dying and death experiences) 8 to 10 months after the death. Ninety-five caregivers of Jewish cancer patients, most of whom were female spouses or children of the deceased. Mean QODD score was 57.2 (standard deviation [SD]=15), which is in the low-moderate range. Place of death, gender and age of the caregiver, and age of the deceased, were associated with QODD score. This retrospective study in Israel demonstrated that the overall quality of dying and death was regarded as poor by almost half of the caregivers. These findings may reflect the relative lack of specialized palliative care and advance care planning in Israel at the time of this study, which took place between 2006 and 2009. Further research and enhancement of palliative care resources may be needed in Israel and several encouraging recent developments (e.g. staff training and legislation) suggest that such changes are now underway.

Compaction die for forming a solid annulus on a right circular cylinder. [Patent application

DOEpatents

Harlow, J.L.

1981-09-14

A compacting die is disclosed wherein the improvement comprises providing a screen in the die cavity, the screen being positioned parallel to the side walls of said die and dividing the die cavity into center and annular compartments. In addition, the use of this die in a method for producing an annular clad ceramic fuel material is disclosed.

The Effects of Die Relief Agent on the Retention of Full Coverage Castings,

DTIC Science & Technology

1981-02-19

autopolymerizing resin. A diamond rotary instrument and a high speed dental handpiece using air- water coolant were employed to prepare the crown of each tooth...777 109 502 ARMY INST OF DENTAL RESEARCH WASHINGTON DC F/6 6/5 THE EFFECTS OF DIE RELIEF AGENT ON THE RETENTION OF FULL COYERA--ETC(U) FES 81 S 6...Kuffler" 4W Eugene F.Huget, COL, (Ret.) .9. PERFORMING ORGANIZATION NAME AND ADDRESS 10. PROGRAM ELEMENT. PROJECT, TASK U.S. Army Institute of Dental

Living and Dying: A Window on (Christian) Children's Spirituality

ERIC Educational Resources Information Center

Champagne, Elaine

2008-01-01

Faith and beliefs about living and dying are fundamental constituents of spiritual development. However, children are seldom asked to talk about their experiences of life and death. This article has a twofold purpose. It first describes children's expressions on living and dying, as heard during a newly developed programme which encourages…

Clinical nurses' attitudes towards death and caring for dying patients in China.

PubMed

Wang, Liping; Li, Chaxiang; Zhang, Qiongling; Li, YaJie

2018-01-02

To examine Chinese clinical nurses' attitudes towards death and caring for dying patients, and to examine the relationships between clinical nurses' attitudes towards death and caring for dying patients. A convenience sample of 770 clinical nurses from 15 hospitals in China. All participants completed the Chinese version of the Frommelt Attitude Toward Care of the Dying Scale, Form B (FATCOD-B-C), the Chinese version of the Death Attitude Profile-Revised (DAP-R-C), and a demographic questionnaire. The mean score of the FATCOD-B-C items was 95.62 (SD = 7.45). The majority of Chinese clinical nurses were likely to provide care for the dying person's family (mean = 3.77), but did not have a positive attitude towards communication with the dying person(mean = 2.62). The majority of Chinese clinical nurses showed low scores on death avoidance (mean=1.96) and natural acceptance (mean = 1.61), and most of them viewed death as a passageway to a happy afterlife (mean = 4.33). Attitudes towards caring for dying patients were significantly negatively correlated with fear of death (r = -0.120) and positively correlated with approach acceptance (r = 0.127) and natural acceptance (r = 0.117). Factors that predicted clinical nurses' attitudes towards the care of dying patients included education level, fear of death, approach acceptance, religious beliefs, previous education on death and dying, natural acceptance, professional title, and experience with death or dying patients, which accounted for 18.7% of the variance. Nurses' personal attitudes towards death were associated with their attitudes towards the care of dying patients. Training and educational programmes for clinical nurses should take into consideration nurses' personal attitudes towards death as well as their cultural backgrounds and religious beliefs.

Existential concerns about death: a qualitative study of dying patients in a Danish hospice.

PubMed

Moestrup, Lene; Hansen, Helle Ploug

2015-06-01

Research suggests that addressing dying patients' existential concerns can improve their quality of life. We aimed to illuminate dying patients' existential concerns about the impending death through a descriptive analysis of semistructured interviews with 17 patients in Danish hospices. The main findings demonstrated how the patients faced the imminent death without being anxious of death but sorrowful about leaving life. Some patients expressed that they avoided thinking about death. They wished to focus on positive aspects in their daily life. We argue that the patients' existential concerns could not be fully captured by Yalom's existential psychology or by Kübler-Ross's theory about death stages. Patients' complex concerns could be more fully explained taking an outset in Heidegger's phenomenological thinking. © The Author(s) 2014.

Do not let death do us part: 'find-me' signals in communication between dying cells and the phagocytes.

PubMed

Medina, C B; Ravichandran, K S

2016-06-01

The turnover and clearance of cells is an essential process that is part of many physiological and pathological processes. Improper or deficient clearance of apoptotic cells can lead to excessive inflammation and autoimmune disease. The steps involved in cell clearance include: migration of the phagocyte toward the proximity of the dying cells, specific recognition and internalization of the dying cell, and degradation of the corpse. The ability of phagocytes to recognize and react to dying cells to perform efficient and immunologically silent engulfment has been well-characterized in vitro and in vivo. However, how apoptotic cells themselves initiate the corpse removal and also influence the cells within the neighboring environment during clearance was less understood. Recent exciting observations suggest that apoptotic cells can attract phagocytes through the regulated release of 'find-me' signals. More recent studies also suggest that these find-me signals can have additional roles outside of phagocyte attraction to help orchestrate engulfment. This review will discuss our current understanding of the different find-me signals released by apoptotic cells, how they may be relevant in vivo, and their additional roles in facilitating engulfment.

Hubble Sees a Dying Star's Final Moments

NASA Image and Video Library

2015-07-31

A dying star’s final moments are captured in this image from the NASA/ESA Hubble Space Telescope. The death throes of this star may only last mere moments on a cosmological timescale, but this star’s demise is still quite lengthy by our standards, lasting tens of thousands of years! The star’s agony has culminated in a wonderful planetary nebula known as NGC 6565, a cloud of gas that was ejected from the star after strong stellar winds pushed the star’s outer layers away into space. Once enough material was ejected, the star’s luminous core was exposed, enabling its ultraviolet radiation to excite the surrounding gas to varying degrees and causing it to radiate in an attractive array of colors. These same colors can be seen in the famous and impressive Ring Nebula (heic1310), a prominent example of a nebula like this one. Planetary nebulae are illuminated for around 10,000 years before the central star begins to cool and shrink to become a white dwarf. When this happens, the star’s light drastically diminishes and ceases to excite the surrounding gas, so the nebula fades from view. Credit: ESA/Hubble & NASA, Acknowledgement: Matej Novak NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

Key factors affecting dying children and their families.

PubMed

Hinds, Pamela S; Schum, Lisa; Baker, Justin N; Wolfe, Joanne

2005-01-01

The death of a child alters the life and health of others immediately and for the rest of their lives. How a child dies influences parents' abilities to continue their role functions as well as siblings' abilities to make and maintain friendships, and may be the basis for health care providers' decisions to exit direct care roles. Thus, facilitating a "good death"-an obvious care priority for all involved with the dying child-ought also to be a priority for the health of bereaved families and affected health care providers. Making this a care priority is complicated by a serious lack of data, as details of the last hours or weeks of a dying child or adolescent's life are largely unknown. The purpose of this paper is to identify key factors that affect the course of dying children and adolescents and that of their bereaved survivors, and to link those key factors to needed research that could produce clinically relevant findings to improve the care of these patients. Key factors described here include suffering (physical, psychological, and spiritual), communication, decision making, prognostic ambiguities, ability of the seriously ill child to give assent to research participation, and educational preparation of health care providers to give competent end-of-life care.

Interlocking multi-material components made of structured steel sheets and high-pressure die cast aluminium

NASA Astrophysics Data System (ADS)

Senge, S.; Brachmann, J.; Hirt, G.; Bührig-Polaczek, A.

2017-10-01

Lightweight design is a major driving force of innovation, especially in the automotive industry. Using hybrid components made of two or more different materials is one approach to reduce the vehicles weight and decrease fuel consumption. As a possible way to increase the stiffness of multi-material components, this paper presents a process chain to produce such components made of steel sheets and high-pressure die cast aluminium. Prior to the casting sequence the steel sheets are structured in a modified rolling process which enables continuous interlocking with the aluminium. Two structures manufactured by this rolling process are tested. The first one is a channel like structure and the second one is a channel like structure with undercuts. These undercuts enable the formation of small anchors when the molten aluminium fills them. The correlation between thickness reduction during rolling and the shape of the resulting structure was evaluated for both structures. It can be stated that channels with a depth of up to 0.5 mm and a width of 1 mm could be created. Undercuts with different size depending on the thickness reduction could be realised. Subsequent aluminium high-pressure die casting experiments were performed to determine if the surface structure can be filled gap-free with molten aluminium during the casting sequence and if a gap-free connection can be achieved after contraction of the aluminium. The casting experiments showed that both structures could be filled during the high-pressure die casting. The channel like structure results in a gap between steel and aluminium after contraction of the cast metal whereas the structure with undercuts leads to a good interlocking resulting in a gap-free connection.

S-process studies using single and pulsed neutron exposures

NASA Astrophysics Data System (ADS)

Beer, H.

The formation of heavy elements by slow neutron capture (s-process) is investigated. A pulsed neutron irradiation leading to an exponential exposure distribution is dominant for nuclei from A = 90 to 200. For the isotopes from iron to zirconium an additional 'weak' s-process component must be superimposed. Calculations using a single or another pulsed neutron exposure for this component have been carried out in order to reproduce the abundance pattern of the s-only and s-process dominant isotopes. For the adjustment of these calculations to the empirical values, the inclusion of new capture cross section data on Se76 and Y89 and the consideration of the branchings at Ni63, Se79, and Kr85 was important. The combination of an s-process with a single and a pulsed neutron exposure yielded a better representation of empirical abundances than a two component pulsed s-process.

Exposure of trees to drought-induced die-off is defined by a common climatic threshold across different vegetation types

PubMed Central

Mitchell, Patrick J; O'Grady, Anthony P; Hayes, Keith R; Pinkard, Elizabeth A

2014-01-01

Increases in drought and temperature stress in forest and woodland ecosystems are thought to be responsible for the rise in episodic mortality events observed globally. However, key climatic drivers common to mortality events and the impacts of future extreme droughts on tree survival have not been evaluated. Here, we characterize climatic drivers associated with documented tree die-off events across Australia using standardized climatic indices to represent the key dimensions of drought stress for a range of vegetation types. We identify a common probabilistic threshold associated with an increased risk of die-off across all the sites that we examined. We show that observed die-off events occur when water deficits and maximum temperatures are high and exist outside 98% of the observed range in drought intensity; this threshold was evident at all sites regardless of vegetation type and climate. The observed die-off events also coincided with at least one heat wave (three consecutive days above the 90th percentile for maximum temperature), emphasizing a pivotal role of heat stress in amplifying tree die-off and mortality processes. The joint drought intensity and maximum temperature distributions were modeled for each site to describe the co-occurrence of both hot and dry conditions and evaluate future shifts in climatic thresholds associated with the die-off events. Under a relatively dry and moderate warming scenario, the frequency of droughts capable of inducing significant tree die-off across Australia could increase from 1 in 24 years to 1 in 15 years by 2050, accompanied by a doubling in the occurrence of associated heat waves. By defining commonalities in drought conditions capable of inducing tree die-off, we show a strong interactive effect of water and high temperature stress and provide a consistent approach for assessing changes in the exposure of ecosystems to extreme drought events. PMID:24772285

Developing a Blended Course on Dying, Loss, and Grief

PubMed Central

Kavanaugh, Karen; Andreoni, V. Ann; Wilkie, Diana J.; Burgener, Sandra; Buschmann, MaryBeth Tank; Henderson, Gloria; Hsiung, Yi-Fang Yvonne; Zhao, Zhongsheng

2010-01-01

An important component of end-of-life education is to provide health professionals with content related to dying, loss, and grief. The authors describe the strategies used to develop and offer a blended course (integration of classroom face-to-face learning with online learning) that addressed the sensitive and often emotional content associated with grieving and bereavement. Using Kolb’s experiential learning theory, a set of 4 online learning modules, with engaging, interactive elements, was created. Course evaluations demonstrated the success of the blended course in comparison to the traditional, exclusive face-to-face approach. PMID:19412055

Aerial image based die-to-model inspections of advanced technology masks

NASA Astrophysics Data System (ADS)

Kim, Jun; Lei, Wei-Guo; McCall, Joan; Zaatri, Suheil; Penn, Michael; Nagpal, Rajesh; Faivishevsky, Lev; Ben-Yishai, Michael; Danino, Udy; Tam, Aviram; Dassa, Oded; Balasubramanian, Vivek; Shah, Tejas H.; Wagner, Mark; Mangan, Shmoolik

2009-10-01

Die-to-Model (D2M) inspection is an innovative approach to running inspection based on a mask design layout data. The D2M concept takes inspection from the traditional domain of mask pattern to the preferred domain of the wafer aerial image. To achieve this, D2M transforms the mask layout database into a resist plane aerial image, which in turn is compared to the aerial image of the mask, captured by the inspection optics. D2M detection algorithms work similarly to an Aerial D2D (die-to-die) inspection, but instead of comparing a die to another die it is compared to the aerial image model. D2M is used whenever D2D inspection is not practical (e.g., single die) or when a validation of mask conformity to design is needed, i.e., for printed pattern fidelity. D2M is of particular importance for inspection of logic single die masks, where no simplifying assumption of pattern periodicity may be done. The application can tailor the sensitivity to meet the needs at different locations, such as device area, scribe lines and periphery. In this paper we present first test results of the D2M mask inspection application at a mask shop. We describe the methodology of using D2M, and review the practical aspects of the D2M mask inspection.

Proper care for the dying: a critical public issue.

PubMed Central

Crispell, K R; Gomez, C F

1987-01-01

The ability of the medical profession to sustain life, or more appropriately, to prolong dying, in patients with terminal illness, creates a most complex and controversial situation for all involved: the patient, if mentally alert; the patient's family; and the medical care team including physicians, nurses and attendants. This situation is especially complex in large acute care hospitals where medical and nursing students, residents and house officers receive advanced medical training. A major problem, prolonging the dying of the terminally ill, with its medical, legal, ethical and economic complexities now confronts American society. The problem is particularly acute in teaching hospitals, in which one finds a disproportionate number of terminally ill patients. The ability to work at these questions as a community rather than as adversaries will determine much about the ability of the health care system to respect the dignity and autonomy of those who seek aid and comfort when faced with serious illness and impending death. Better communication between the physicians, health care providers, the lawyers and ethicists must be developed in order to solve these problems. Over the next ten years society and our elected representatives will be making very demanding decisions about the use of the health dollar. One possible way to prevent increasing costs is to reach significant agreement on the proper care of the dying. Proper care for the dying is being considered, discussed, and evaluated by very thoughtful people. It is not governments which should decide who is to live or who is to die. There is the serious problem of the 'slippery slope' to euthanasia by omission if cost containment becomes the major force in formulating policy on the proper care of the dying. PMID:3612698

The dying neonate: family-centered end-of-life care.

PubMed

De Lisle-Porter, Martine; Podruchny, Ann Marie

2009-01-01

There is a need in the NICU for an end-of-life care guideline that nurses can follow when working with dying infants and their families. Maintaining intravenous access to relieve the infant's pain, communicating sensitively to the family, and creating precious, everlasting memories are goals that should be part of every dying infant's care. The nurse's ability to partner with the family in caring for the infant is integral to helping the family take the first steps in their grief journey. Evidence-based literature provides NICU nurses with the knowledge that they are the facilitators of end-of-life care for dying infants. New mothers and fathers are not aware of the caring parental tasks they can perform for their dying baby. They look to and depend on their infant's nurses to encourage them. The guideline included here provides nurses with a tool for ensuring that families have the opportunity to create memories that will not only help them with their immediate pain, but also comfort them for a lifetime.

Solid explosive plane-wave lenses pressed-to-shape with dies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Olinger, B.

2007-11-01

Solid-explosive plane-wave lenses 1", 2" and 4¼" in diameter have been mass-produced from components pressed-to-shape with aluminum dies. The method used to calculate the contour between the solid plane-wave lens components pressed-to-shape with the dies is explained. The steps taken to press, machine, and assemble the lenses are described. The method of testing the lenses, the results of those tests, and the corrections to the dies are reviewed. The work on the ½", 8", and 12" diameter lenses is also discussed.

Die Energiebranche am Beginn der digitalen Transformation: aus Versorgern werden Utilities 4.0

NASA Astrophysics Data System (ADS)

Doleski, Oliver D.

Die traditionelle Energieversorgung befindet sich in einer Zäsur. Das seit Jahrzehnten bewährte und stabile Geschäftsmodell einer zuverlässig planbaren, zentralen Energieerzeugung mit anschließender unidirektionaler Verteilung geriet spätestens seit der Energiewende des Jahres 2011 immer mehr unter Druck. Angesichts fortschreitender Digitalisierung und Dezentralisierung einerseits und gestiegener Erwartungshaltung der Kunden gegenüber "ihrem" Versorger andererseits sieht sich die Energiebranche heute einem epochalen Transformationsprozess gegenübergestellt. Bei diesem entwickeln sich aus den monopolistischen Versorgern des 19. und 20. Jahrhunderts (Utility 1.0), über die liberalisierten Energieversorgungsunternehmen (Utility 2.0) und Energiedienstleistungsunternehmen (Utility 3.0) heutiger Prägung, die digitalen Energiedienstleistungsunternehmen (Utility 4.0) von morgen. Oliver D. Doleski beschränkt sich in seinem Beitrag nicht auf die reine Beschreibung dieses Veränderungsprozesses an sich. Vielmehr werden darüber hinaus sowohl die mit dieser Entwicklung verbundenen übergeordneten Ziele als auch die wesentlichen Anforderungen an erfolgreiche Utilities 4.0 skizziert. Das Kapitel endet mit einem prägnanten Überblick profitabler Betätigungsfelder, die zur Sicherung der ökonomischen Zukunft von Energiekonzernen, Regionalversorgern und Stadtwerken beitragen können.

Clinical Criteria for Physician Aid in Dying.

PubMed

Orentlicher, David; Pope, Thaddeus Mason; Rich, Ben A

2016-03-01

More than 20 years ago, even before voters in Oregon had enacted the first aid in dying (AID) statute in the United States, Timothy Quill and colleagues proposed clinical criteria AID. Their proposal was carefully considered and temperate, but there were little data on the practice of AID at the time. (With AID, a physician writes a prescription for life-ending medication for a terminally ill, mentally capacitated adult.) With the passage of time, a substantial body of data on AID has developed from the states of Oregon and Washington. For more than 17 years, physicians in Oregon have been authorized to provide a prescription for AID. Accordingly, we have updated the clinical criteria of Quill, et al., based on the many years of experience with AID. With more jurisdictions authorizing AID, it is critical that physicians can turn to reliable clinical criteria. As with any medical practice, AID must be provided in a safe and effective manner. Physicians need to know (1) how to respond to a patient's inquiry about AID, (2) how to assess patient decision making capacity, and (3) how to address a range of other issues that may arise. To ensure that physicians have the guidance they need, Compassion & Choices convened the Physician Aid-in-Dying Clinical Criteria Committee, in July 2012, to create clinical criteria for physicians who are willing to provide AID to patients who request it. The committee includes experts in medicine, law, bioethics, hospice, nursing, social work, and pharmacy. Using an iterative consensus process, the Committee drafted the criteria over a one-year period.

New Lubricant for Pressure Die Casting,

DTIC Science & Technology

synthetic acids, finely dispersed graphite preparations, etc. The new lubricants are not inferior in their properties to the well known foreign lubricants antilov, olea , and emtek used in pressure die casting.

On-Die Sensors for Transient Events

NASA Astrophysics Data System (ADS)

Suchak, Mihir Vimal

Failures caused by transient electromagnetic events like Electrostatic Discharge (ESD) are a major concern for embedded systems. The component often failing is an integrated circuit (IC). Determining which IC is affected in a multi-device system is a challenging task. Debugging errors often requires sophisticated lab setups which require intentionally disturbing and probing various parts of the system which might not be easily accessible. Opening the system and adding probes may change its response to the transient event, which further compounds the problem. On-die transient event sensors were developed that require relatively little area on die, making them inexpensive, they consume negligible static current, and do not interfere with normal operation of the IC. These circuits can be used to determine the pin involved and the level of the event in the event of a transient event affecting the IC, thus allowing the user to debug system-level transient events without modifying the system. The circuit and detection scheme design has been completed and verified in simulations with Cadence Virtuoso environment. Simulations accounted for the impact of the ESD protection circuits, parasitics from the I/O pin, package and I/O ring, and included a model of an ESD gun to test the circuit's response to an ESD pulse as specified in IEC 61000-4-2. Multiple detection schemes are proposed. The final detection scheme consists of an event detector and a level sensor. The event detector latches on the presence of an event at a pad, to determine on which pin an event occurred. The level sensor generates current proportional to the level of the event. This current is converted to a voltage and digitized at the A/D converter to be read by the microprocessor. Detection scheme shows good performance in simulations when checked against process variations and different kind of events.

Early and late signs that precede dying among older persons in nursing homes: the multidisciplinary team's perspective.

PubMed

Åvik Persson, Helene; Sandgren, Anna; Fürst, Carl-Johan; Ahlström, Gerd; Behm, Lina

2018-06-04

Nursing home residents in Sweden are old, frail and usually have multiple morbidities which often make dying a prolonged suffering. It has been found that older persons at nursing homes receive far less palliative care than younger persons, partly because it is difficult to identify when the final stage of life begins. The identification may help the staff to enable the older person and their families to participate in planning the care in accordance with their own preferences and values. With this in mind the aim was to explore the experiences of early and late signs preceding dying in older persons in nursing homes from the multidisciplinary team's perspective. The focus group method was used to interview 20 health-care professionals on the basis of semi-structured questions. Four focus groups were conducted at four nursing homes in two counties in southern Sweden. The groups included different professionals such as assistant nurses, registered nurses, occupational therapists, physiotherapists, social workers and unit managers. The analysis was conducted according to the focus group method developed by Kruger and Casey. The analysis revealed one major theme, from unawareness to obviousness, which illustrates that the participants experienced dying as a happening, not a process, and found it difficult to identify early signs. Even though it was a new way of thinking, several suggestions of early signs were presented. The main category "Going into a bubble" illustrates early signs, which meant that the older person showed signs of wanting to withdraw from the outside world. The main category "The body begins to shut down" illustrates late signs, which meant that the older person showed signs that indicate that the body starts to prepare for death. This study conveys new knowledge concerning the multidisciplinary team's collective experience of early and late signs that precede dying. This knowledge can increase the understanding of when a palliative care approach

9 CFR 309.3 - Dead, dying, disabled, or diseased and similar livestock.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Dead, dying, disabled, or diseased and... AND VOLUNTARY INSPECTION AND CERTIFICATION ANTE-MORTEM INSPECTION § 309.3 Dead, dying, disabled, or diseased and similar livestock. (a) Livestock found to be dead or in a dying condition on the premises of...

9 CFR 309.3 - Dead, dying, disabled, or diseased and similar livestock.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 9 Animals and Animal Products 2 2011-01-01 2011-01-01 false Dead, dying, disabled, or diseased and... AND VOLUNTARY INSPECTION AND CERTIFICATION ANTE-MORTEM INSPECTION § 309.3 Dead, dying, disabled, or diseased and similar livestock. (a) Livestock found to be dead or in a dying condition on the premises of...

9 CFR 309.3 - Dead, dying, disabled, or diseased and similar livestock.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 9 Animals and Animal Products 2 2013-01-01 2013-01-01 false Dead, dying, disabled, or diseased and... AND VOLUNTARY INSPECTION AND CERTIFICATION ANTE-MORTEM INSPECTION § 309.3 Dead, dying, disabled, or diseased and similar livestock. (a) Livestock found to be dead or in a dying condition on the premises of...

9 CFR 309.3 - Dead, dying, disabled, or diseased and similar livestock.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 9 Animals and Animal Products 2 2014-01-01 2014-01-01 false Dead, dying, disabled, or diseased and... AND VOLUNTARY INSPECTION AND CERTIFICATION ANTE-MORTEM INSPECTION § 309.3 Dead, dying, disabled, or diseased and similar livestock. (a) Livestock found to be dead or in a dying condition on the premises of...

9 CFR 309.3 - Dead, dying, disabled, or diseased and similar livestock.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 9 Animals and Animal Products 2 2012-01-01 2012-01-01 false Dead, dying, disabled, or diseased and... AND VOLUNTARY INSPECTION AND CERTIFICATION ANTE-MORTEM INSPECTION § 309.3 Dead, dying, disabled, or diseased and similar livestock. (a) Livestock found to be dead or in a dying condition on the premises of...

Unfertilized frog eggs die by apoptosis following meiotic exit

PubMed Central

2011-01-01

Background A characteristic feature of frog reproduction is external fertilization accomplished outside the female's body. Mature fertilization-competent frog eggs are arrested at the meiotic metaphase II with high activity of the key meiotic regulators, maturation promoting factor (MPF) and cytostatic factor (CSF), awaiting fertilization. If the eggs are not fertilized within several hours of ovulation, they deteriorate and ultimately die by as yet unknown mechanism. Results Here, we report that the vast majority of naturally laid unfertilized eggs of the African clawed frog Xenopus laevis spontaneously exit metaphase arrest under various environmental conditions and degrade by a well-defined apoptotic process within 48 hours after ovulation. The main features of this process include cytochrome c release, caspase activation, ATP depletion, increase of ADP/ATP ratio, apoptotic nuclear morphology, progressive intracellular acidification, and egg swelling. Meiotic exit seems to be a prerequisite for execution of the apoptotic program, since (i) it precedes apoptosis, (ii) apoptotic events cannot be observed in the eggs maintaining high activity of MPF and CSF, and (iii) apoptosis in unfertilized frog eggs is accelerated upon early meiotic exit. The apoptotic features cannot be observed in the immature prophase-arrested oocytes, however, the maturation-inducing hormone progesterone renders oocytes susceptible to apoptosis. Conclusions The study reveals that naturally laid intact frog eggs die by apoptosis if they are not fertilized. A maternal apoptotic program is evoked in frog oocytes upon maturation and executed after meiotic exit in unfertilized eggs. The meiotic exit is required for execution of the apoptotic program in eggs. The emerging anti-apoptotic role of meiotic metaphase arrest needs further investigation. PMID:22195698

Discussion of death and dying in surgical textbooks.

PubMed

Easson, A M; Crosby, J A; Librach, S L

2001-07-01

Quality end-of-life care is an increasing concern for the public and the medical profession. Surgical textbooks could serve as an important educational and reference resource to improve this care. Four general surgical textbooks were scored for helpful information on death and dying for eight surgical diseases. For each disease, nine content domains related to care of the dying patient were evaluated. Three texts included a chapter on cancer that was evaluated separately. Disease epidemiology, prognosis/prevention, progression, and medical interventions were generally well discussed in all textbooks. However, little helpful information was provided with regards to breaking bad news/advanced care planning, mode of death, treatment decision-making, effect on family/surgeon, and symptom management. Cancer chapters also addressed only a few of these concerns. Death and the dying patient are sufficiently frequent in surgical practice that it would be appropriate to increase the amount of information provided.

Cheatgrass die-offs as an opportunity for restoration in the Great Basin, USA: Will local or commercial native plants succeed where exotic invaders fail?

Treesearch

Owen W. Baughman; Susan E. Meyer; Zachary T. Aanderud; Elizabeth A. Leger

2016-01-01

Bromus tectorum (cheatgrass) has widely invaded the Great Basin, U.S.A. The sporadic natural phenomenon of complete stand failure ('die-off'') of this invader may present opportunities to restore native plants. A recent die-off in Nevada was precision-planted with seeds of the native grasses Poa secunda (Sandberg bluegrass) and Elymus elymoides (...

Results from a new die-to-database reticle inspection platform

NASA Astrophysics Data System (ADS)

Broadbent, William; Xiong, Yalin; Giusti, Michael; Walsh, Robert; Dayal, Aditya

2007-03-01

A new die-to-database high-resolution reticle defect inspection system has been developed for the 45nm logic node and extendable to the 32nm node (also the comparable memory nodes). These nodes will use predominantly 193nm immersion lithography although EUV may also be used. According to recent surveys, the predominant reticle types for the 45nm node are 6% simple tri-tone and COG. Other advanced reticle types may also be used for these nodes including: dark field alternating, Mask Enhancer, complex tri-tone, high transmission, CPL, EUV, etc. Finally, aggressive model based OPC will typically be used which will include many small structures such as jogs, serifs, and SRAF (sub-resolution assist features) with accompanying very small gaps between adjacent structures. The current generation of inspection systems is inadequate to meet these requirements. The architecture and performance of a new die-to-database inspection system is described. This new system is designed to inspect the aforementioned reticle types in die-to-database and die-to-die modes. Recent results from internal testing of the prototype systems are shown. The results include standard programmed defect test reticles and advanced 45nm and 32nm node reticles from industry sources. The results show high sensitivity and low false detections being achieved.

Method of making cascaded die mountings with springs-loaded contact-bond options

DOEpatents

Hsu, John S [Oak Ridge, TN; Adams, Donald J [Knoxville, TN; Su, Gui-Jia [Knoxville, TN; Marlino, Laura D [Oak Ridge, TN; Ayers, Curtis W [Kingston, TN; Coomer, Chester [Knoxville, TN

2007-06-19

A cascaded die mounting device and method using spring contacts for die attachment, with or without metallic bonds between the contacts and the dies, is disclosed. One embodiment is for the direct refrigerant cooling of an inverter/converter carrying higher power levels than most of the low power circuits previously taught, and does not require using a heat sink.

Numerical simulation on semi-solid die-casting of magnesium matrix composite based on orthogonal experiment

NASA Astrophysics Data System (ADS)

Liu, Huihui; He, Xiongwei; Guo, Peng

2017-04-01

Three factors (pouring temperature, injection speed and mold temperature) were selected to do three levels L9 (33)orthogonal experiment, then simulate processing of semi-solid die-casting of magnesium matrix composite by Flow-3D software. The stress distribution, temperature field and defect distribution of filling process were analyzed to find the optimized processing parameter with the help of orthogonal experiment. The results showed that semi-solid has some advantages of well-proportioned stress and temperature field, less defect concentrated in the surface. The results of simulation were the same as the experimental results.

Do not let death do us part: ‘find-me' signals in communication between dying cells and the phagocytes

PubMed Central

Medina, C B; Ravichandran, K S

2016-01-01

The turnover and clearance of cells is an essential process that is part of many physiological and pathological processes. Improper or deficient clearance of apoptotic cells can lead to excessive inflammation and autoimmune disease. The steps involved in cell clearance include: migration of the phagocyte toward the proximity of the dying cells, specific recognition and internalization of the dying cell, and degradation of the corpse. The ability of phagocytes to recognize and react to dying cells to perform efficient and immunologically silent engulfment has been well-characterized in vitro and in vivo. However, how apoptotic cells themselves initiate the corpse removal and also influence the cells within the neighboring environment during clearance was less understood. Recent exciting observations suggest that apoptotic cells can attract phagocytes through the regulated release of ‘find-me' signals. More recent studies also suggest that these find-me signals can have additional roles outside of phagocyte attraction to help orchestrate engulfment. This review will discuss our current understanding of the different find-me signals released by apoptotic cells, how they may be relevant in vivo, and their additional roles in facilitating engulfment. PMID:26891690

Prior suicide attempts are less common in suicide decedents who died by firearms relative to those who died by other means.

PubMed

Anestis, Michael D

2016-01-01

Suicide prevention efforts often center on the identification of risk factors (e.g., prior suicide attempts); however, lists of risk factors without consideration of context may prove incapable of impacting suicide rates. One contextual variable worth considering is attempt method. Utilizing data from the National Violent Death Reporting System (2005-2012), I examined suicide deaths (n=71,775) by firearms and other means to determine whether prior suicide attempts were more common in one group versus the other. Significantly fewer suicide decedents who died by firearms reported a prior history of suicide attempts (12.10%) than did decedents who died by other means (28.66%). This result was further replicated within each state that contributed data to the NVDRS. Only 17 states have contributed to the NVDRS thus far and, within those states, not all suicide deaths were reported. Due to the nature of the data, I was unable to test proposed mediators within our model. Suicide decedents who die by firearms may die on their first attempt more often than other decedents due to a capability and willingness to utilize a highly lethal means. Current risk assessment protocols may be ill equipped to identify such individuals prospectively on their own. Broader methods of implementing means restriction (e.g., legislation) may thus be pivotal in suicide prevention efforts. Copyright © 2015 Elsevier B.V. All rights reserved.

The power of consoling presence - hospice nurses’ lived experience with spiritual and existential care for the dying

PubMed Central

2014-01-01

Background Being with dying people is an integral part of nursing, yet many nurses feel unprepared to accompany people through the process of dying, reporting a lack of skills in psychosocial and spiritual care, resulting in high levels of moral distress, grief and burnout. The aim of this study is to describe the meaning of hospice nurses’ lived experience with alleviating dying patients’ spiritual and existential suffering. Methods This is a qualitative study. Hospice nurses were interviewed individually and asked to narrate about their experiences with giving spiritual and existential care to terminally ill hospice patients. Data analysis was conducted using phenomenological hermeneutical method. Results The key spiritual and existential care themes identified, were sensing existential and spiritual distress, tuning inn and opening up, sensing the atmosphere in the room, being moved and touched, and consoling through silence, conversation and religious consolation. Conclusions Consoling existential and spiritual distress is a deeply personal and relational practice. Nurses have a potential to alleviate existential and spiritual suffering through consoling presence. By connecting deeply with patients and their families, nurses have the possibility to affirm the patients’ strength and facilitate their courage to live a meaningful life and die a dignified death. PMID:25214816

Nurses' views on legalising assisted dying in New Zealand: A cross-sectional study.

PubMed

Wilson, Michael; Oliver, Pam; Malpas, Phillipa

2018-04-15

This study investigated New Zealand nurses' views on legalising assisted dying across a range of clinical conditions, nurses' willingness to engage in legal assisted dying, potential deterrents and enablers to such engagement, and nurses' perceptions of the proper role of their professional bodies in relation to legalising assisted dying. A Bill for legalising assisted dying is currently before the New Zealand parliament. Of the 16 jurisdictions where assisted dying has been specifically legislated, only the Canadian federal statute provides nurses with explicit legal protection for their performance of assisted dying-related tasks. An absence of policy development and planning for safe nursing practice prior to legalisation of assisted dying results in a gap in professional support and guidance. Exploratory cross-sectional survey. A self-selected sample of 475 New Zealand nurses responded to an anonymous online survey disseminated through the newsletters and websites of relevant medical and nursing professional bodies. A sub-sample of nurses who expressed support for or ambivalence about legalisation (n = 356): rated their level of support for legalising assisted dying in New Zealand across a range of medical conditions, and their willingness to participate in a range of assisted dying tasks; identified barriers and facilitators to potential participation; and assessed the responsibility of the professional bodies to provide practice supports. Mixed-method approach using descriptive analysis of quantitative data; qualitative data were analysed thematically. Nurses supported legalisation at a rate (67%) significantly greater than that of doctors (37%) and for a diverse range of medical conditions. Most supporting nurses were willing to engage in the full range of relevant assisted dying roles. They identified several practical and ethical supports as essential to safe engagement, in particular practice guidelines, specific training, legal protections, clinical

Characterization of the interfacial heat transfer coefficient for hot stamping processes

NASA Astrophysics Data System (ADS)

Luan, Xi; Liu, Xiaochuan; Fang, Haomiao; Ji, Kang; El Fakir, Omer; Wang, LiLiang

2016-08-01

In hot stamping processes, the interfacial heat transfer coefficient (IHTC) between the forming tools and hot blank is an essential parameter which determines the quenching rate of the process and hence the resulting material microstructure. The present work focuses on the characterization of the IHTC between an aluminium alloy 7075-T6 blank and two different die materials, cast iron (G3500) and H13 die steel, at various contact pressures. It was found that the IHTC between AA7075 and cast iron had values 78.6% higher than that obtained between AA7075 and H13 die steel. Die materials and contact pressures had pronounced effects on the IHTC, suggesting that the IHTC can be used to guide the selection of stamping tool materials and the precise control of processing parameters.

Dying in the Hospital: Perspectives of family members.

PubMed

Dose, Ann Marie; Carey, Elise C; Rhudy, Lori M; Chiu, Yichen; Frimannsdottir, Katrin; Ottenberg, Abigale L; Koenig, Barbara A

2015-01-01

Although most patients express a preference to die at home, many (over 30 percent) still die in hospital. This study's purpose was to explore the experience of hospital death from the perspective of patients' family members. interviews were conducted with family members of patients who had died at hospitals affiliated with a large tertiary referral centre in the United States. Content analysis was used to analyze findings. We interviewed 30 family members by phone. Themes were arranged by time frame: before death, time of death, and after death. Families do not interpret clinical cues leading up to death in the same way healthcare providers do; families need clear and direct explanations from providers. Clinicians should assess patient and family understandings of prognosis and communicate clearly and directly. Family members value being with their loved one at the time of death, and they value spending time with the body after death; this should be facilitated in clinical practice.

Study of radial die-wall pressure changes during pharmaceutical powder compaction.

PubMed

Abdel-Hamid, Sameh; Betz, Gabriele

2011-04-01

In tablet manufacturing, less attention is paid to the measurement of die-wall pressure than to force-displacement diagrams. Therefore, the aim of this study was to investigate radial stress change during pharmaceutical compaction. The Presster(TM), a tablet-press replicator, was used to characterize compaction behavior of microcrystalline cellulose (viscoelastic), calcium hydrogen phosphate dihydrate (brittle), direct compressible mannitol (plastic), pre-gelatinized starch (plastic/elastic), and spray dried lactose monohydrate (plastic/brittle) by measuring radial die-wall pressure; therefore powders were compacted at different (pre) compaction pressures as well as different speeds. Residual die-wall pressure (RDP) and maximum die-wall pressure (MDP) were measured. Various tablet physical properties were correlated to radial die-wall pressure. With increasing compaction pressure, RDP and MDP (P < 0.0001) increased for all materials, with increasing precompaction RDP decreased for plastic materials (P < 0.05), whereas with increasing speed MDP decreased for all materials (P < 0.05). During decompression, microcrystalline cellulose and pre-gelatinized starch showed higher axial relaxation, whereas mannitol and lactose showed higher radial relaxation, calcium hydrogen phosphate showed high axial and radial relaxations. Plastic and brittle materials showed increased tendencies for friction because of high radial relaxation. Die-wall monitoring is suggested as a valuable tool for characterizing compaction behavior of materials and detecting friction phenomena in the early stage of development.

Nurses attitudes towards death, dying patients and euthanasia: A descriptive study.

PubMed

Ay, Melike Ayça; Öz, Fatma

2018-01-01

Attitudes of nurses towards death and related concepts influence end-of-life care. Determining nurses' views and attitudes towards these concepts and the factors that affect them are necessary to ensure quality end-of-life care. The purpose of this study was to determine nurses' views and attitudes about death, dying patient, euthanasia and the relationships between nurses' characteristics. Participants consist of the nurses who volunteered to take part in this descriptive study from 25 hospitals (n = 340) which has a paediatric or adult intensive care unit and located within the boundaries of Ankara, Turkey. 'Nurse Information Form' and 'Attitude Scale about Euthanasia, Death and Dying Patients (DAS)' were used as data collection tool. Ethical consideration: Written permissions were received from the 'Noninterventional Clinical Researches Ethics Board' of authors' university and education councils of each hospital. Informed consent was obtained from participants. It is found that there are statistically significant difference among the factors of marital status, having a child, years of experience, bereavement experience, affected by working with dying patient, definition of euthanasia, views about patients who are appropriate for euthanasia, views about patients who desire to die and feeling need for counselling on these concepts according to the mean total score of nurses' attitudes about euthanasia, death and dying patient (p < 0.05). The results indicate that nurses are negatively affected to face the concepts of death, euthanasia and work with dying patient. This is reflected in their attitude. In order to gain positive attitude towards death, dying patient and euthanasia, the implementation of training and consulting services to nurses at appropriate intervals during both education and professional life are required.

Effect of young’s modulus on springback for low, medium and high carbon steels during cold drawing of seamless tubes

NASA Astrophysics Data System (ADS)

Karanjule, D. B.; Bhamare, S. S.; Rao, T. H.

2018-04-01

Cold drawing is widely used deformation process for seamless tube manufacturing. Springback is one of the major problem faced in tube drawing. Springback is due to the elastic energy stored in the tubes during forming process. It is found that this springback depends upon Young’s modulus of the material. This paper reports mechanical testing of three grades of steels viz. low carbon steel, medium carbon steel and high carbon steel to measure their Young’s modulus and corresponding springback. The results shows that there is 10-20 % variation in the Young’s modulus and inverse proportion between the springback and Young’s modulus. More the percentage of carbon, more the strength, less the value of Young’s modulus and more will springback. The study further leads to identify optimum die semi angle of 15 degree, land width of 10 mm and drawing speed of 8, 6 and 4 m/min for least springback in all the three grades respectively and die semi angle as a most dominant factor causing springback.

Facilitating Attachment between School-Aged Children and a Dying Parent

ERIC Educational Resources Information Center

Saldinger, Amy; Cain, Albert C.; Porterfield, Katherine; Lohnes, Kelly

2004-01-01

A qualitative, community study of 58 parentally bereaved children and their 35 surviving parents illustrates how families take advantage of forewarning of death to foster connections between children and dying parents and prepare for youngsters' continued attachment to dying parents after the death. Children and parents displayed strong yearnings…

Method of forming through substrate vias (TSVs) and singulating and releasing die having the TSVs from a mechanical support substrate

DOEpatents

Okandan, Murat; Nielson, Gregory N

2014-12-09

Accessing a workpiece object in semiconductor processing is disclosed. The workpiece object includes a mechanical support substrate, a release layer over the mechanical support substrate, and an integrated circuit substrate coupled over the release layer. The integrated circuit substrate includes a device layer having semiconductor devices. The method also includes etching through-substrate via (TSV) openings through the integrated circuit substrate that have buried ends at or within the release layer including using the release layer as an etch stop. TSVs are formed by introducing one or more conductive materials into the TSV openings. A die singulation trench is etched at least substantially through the integrated circuit substrate around a perimeter of an integrated circuit die. The integrated circuit die is at least substantially released from the mechanical support substrate.

Understandings of death and dying for people of Chinese origin.

PubMed

Hsu, Chiung-yin; O'Connor, Margaret; Lee, Susan

2009-02-01

This article introduces the primary beliefs about ancestor worship, Taoism, Confucianism, Buddhism and traditional Chinese medicine that have influenced Chinese people for thousands of years, particularly in relation to death and dying. These cultures and traditions remain important for Chinese people wherever they live. Over a long period, Chinese people have integrated these philosophies and religions to form the basis of their culture and traditions. Although they agree that death is a natural part of the life span, a unique belief about death and dying has emerged among the Chinese from this integration. From this, the people find a significant definition of death and dying.

Processing effects in production of composite prepreg by hot melt impregnation

NASA Astrophysics Data System (ADS)

Chmielewski, C.; Jayaraman, K.; Petty, C. A.

1993-06-01

The hot melt impregnation process for producing composite prepreg has been studied. The role of the exit die is highlighted by operating without impregnation bars. Experimental results show that when a fiber tow is pulled through a resin bath and then through a wedge shaped die, the total resin mass fraction and the extent of resin impregnation in the tow increase with the processing viscosity. The penetration of resin into a fiber bundle is greater when the resin viscosity is higher. This trend is unchanged over a range of tow speeds up to the breaking point. A theoretical model is developed to describe the effect of processing conditions and die geometry on the degree of impregnation. Calculations with this model indicate that for a given die geometry, the degree of impregnation increases from 58 percent to 90 percent as the ratio of the clearance between the tow and the die wall, to the total die gap is decreased from 0.15 to 0.05. Physical arguments related to the effective viscosity of the prepreg show that the clearance ratio is independent of the tow speed, but decreases as the ratio of the effective shear viscosity of the prepreg to the resin viscosity increases. This provides a connection between the experimental results obtained with varying resin viscosity and the computational results obtained with varying clearance values at the die inlet.

Death and Dying Anxiety among Bereaved and Nonbereaved Elderly Parents

ERIC Educational Resources Information Center

Azaiza, Faisal; Ron, Pnina; Shoham, Meyrav; Tinsky-Roimi, Tal

2011-01-01

This study examines differences in death and dying anxiety between bereaved and nonbereaved elderly Israeli parents, as well as correlates of these factors among bereaved parents. A total of 97 parents (49 bereaved, 48 nonbereaved) completed measures of death and dying anxiety and religiosity. Bereaved parents reported significantly higher dying…

Formation Mechanism of Discoloration on Die-Cast AZ91D Components Surface After Chemical Conversion

NASA Astrophysics Data System (ADS)

Liu, Bao-sheng; Wei, Ying-hui; Hou, Li-feng

2013-01-01

A notebook (NB) computer component was manufactured from AZ91D Mg alloy by a die-casting process. After chemical conversion treatment, a discoloration was noted on the component surface. The source of this discoloration has been studied in detail by scanning electron microscopy, energy dispersive spectroscopy, and spark atomic absorption spectroscopy. The corrosion resistance was also measured by potentiodynamic polarization, hydrogen evolution and salt spray testing. The formation mechanism for the discoloration which was caused by the residue left behind by excess mold release agent sprayed during the die-casting was discussed in detail. After chemical conversion treatment, the residual-baked mold release agent was apparent on the component surface as "white ash." Consequently, it degraded seriously both the appearance and the corrosion resistance of the manufactured component.

9 CFR 381.194 - Transportation and other transactions concerning dead, dying, disabled, or diseased poultry, and...

Code of Federal Regulations, 2010 CFR

2010-01-01

... concerning dead, dying, disabled, or diseased poultry, and parts of carcasses of poultry that died otherwise... transactions concerning dead, dying, disabled, or diseased poultry, and parts of carcasses of poultry that died... commerce, or importing any dead, dying, disabled, or diseased poultry or parts of the carcasses of any...

9 CFR 381.194 - Transportation and other transactions concerning dead, dying, disabled, or diseased poultry, and...

Code of Federal Regulations, 2012 CFR

2012-01-01

... concerning dead, dying, disabled, or diseased poultry, and parts of carcasses of poultry that died otherwise... transactions concerning dead, dying, disabled, or diseased poultry, and parts of carcasses of poultry that died... commerce, or importing any dead, dying, disabled, or diseased poultry or parts of the carcasses of any...

9 CFR 381.194 - Transportation and other transactions concerning dead, dying, disabled, or diseased poultry, and...

Code of Federal Regulations, 2014 CFR

2014-01-01

... concerning dead, dying, disabled, or diseased poultry, and parts of carcasses of poultry that died otherwise... transactions concerning dead, dying, disabled, or diseased poultry, and parts of carcasses of poultry that died... commerce, or importing any dead, dying, disabled, or diseased poultry or parts of the carcasses of any...

9 CFR 381.194 - Transportation and other transactions concerning dead, dying, disabled, or diseased poultry, and...

Code of Federal Regulations, 2013 CFR

2013-01-01

... concerning dead, dying, disabled, or diseased poultry, and parts of carcasses of poultry that died otherwise... transactions concerning dead, dying, disabled, or diseased poultry, and parts of carcasses of poultry that died... commerce, or importing any dead, dying, disabled, or diseased poultry or parts of the carcasses of any...

9 CFR 381.194 - Transportation and other transactions concerning dead, dying, disabled, or diseased poultry, and...

Code of Federal Regulations, 2011 CFR

2011-01-01

... concerning dead, dying, disabled, or diseased poultry, and parts of carcasses of poultry that died otherwise... transactions concerning dead, dying, disabled, or diseased poultry, and parts of carcasses of poultry that died... commerce, or importing any dead, dying, disabled, or diseased poultry or parts of the carcasses of any...

The quality of dying and death measurement instruments: A systematic psychometric review.

PubMed

Gutiérrez Sánchez, Daniel; Pérez Cruzado, David; Cuesta-Vargas, Antonio I

2018-04-19

To identify instruments that could assess the quality of dying and death and their psychometric properties. To assess the methodological quality of studies on measurement properties. A high quality of death is regarded as a goal at the end of life and, therefore, an assessment of the end of life experience is essential. Many instruments have been developed to evaluate the quality of dying and death. The selection of the most appropriate measure to be used in clinical and research settings is crucial. Psychometric systematic review. We systematically searched ProQuest Medline, SciELO and ProQuest PsycINFO from 1970 - May 2016. Identification and evaluation of instruments that assessed quality of dying and death. Papers were evaluated by two independent reviewers according to the COSMIN checklist with a 4-point scale. A total of 19 studies were included in this review. Seven instruments were found that were specifically designed for assessing quality of dying and death. A retrospective carer proxy report to evaluate this construct was used in most of the papers. The methodological quality of the studies was fair for most of the psychometric characteristics analyzed. Many instruments have been developed to assess the quality of dying and death. The Quality of Dying and Death Questionnaire is the best available measure of the quality of dying and death. It is the only questionnaire identified in this review where all psychometric properties according to the COSMIN checklist have been evaluated. © 2018 John Wiley & Sons Ltd.

Dying to Live: Mourning, Melancholia and the Adolescent Process

ERIC Educational Resources Information Center

Polmear, Caroline

2004-01-01

The author reviews the main points in Freud's 1917 paper "Mourning and Melancholia" and relates them to the process of both normal and troubled adolescent development. Using clinical examples she illustrates the ways in which the processes Freud describes in melancholia operate in some disturbed adolescents such that instead of mourning the lost…

Hubble View of a Dying Star

NASA Image and Video Library

2003-05-21

This image of a dying star, protoplanetary nebula IRAS22036+5306, containing strange, complex structures may help explain the death throes of stars and defy our current understanding of physics. Taken by NASA Wide Field and Planetary Camera 2.

9 CFR 325.20 - Transportation and other transactions concerning dead, dying, disabled, or diseased livestock...

Code of Federal Regulations, 2014 CFR

2014-01-01

... concerning dead, dying, disabled, or diseased livestock, and parts of carcasses of livestock that died... other transactions concerning dead, dying, disabled, or diseased livestock, and parts of carcasses of... transporting in commerce, or importing any dead, dying, disabled or diseased animals or parts of the carcasses...

9 CFR 325.20 - Transportation and other transactions concerning dead, dying, disabled, or diseased livestock...

Code of Federal Regulations, 2012 CFR

2012-01-01

... concerning dead, dying, disabled, or diseased livestock, and parts of carcasses of livestock that died... other transactions concerning dead, dying, disabled, or diseased livestock, and parts of carcasses of... transporting in commerce, or importing any dead, dying, disabled or diseased animals or parts of the carcasses...

9 CFR 325.20 - Transportation and other transactions concerning dead, dying, disabled, or diseased livestock...

Code of Federal Regulations, 2010 CFR

2010-01-01

... concerning dead, dying, disabled, or diseased livestock, and parts of carcasses of livestock that died... other transactions concerning dead, dying, disabled, or diseased livestock, and parts of carcasses of... transporting in commerce, or importing any dead, dying, disabled or diseased animals or parts of the carcasses...

9 CFR 325.20 - Transportation and other transactions concerning dead, dying, disabled, or diseased livestock...

Code of Federal Regulations, 2011 CFR

2011-01-01

... concerning dead, dying, disabled, or diseased livestock, and parts of carcasses of livestock that died... other transactions concerning dead, dying, disabled, or diseased livestock, and parts of carcasses of... transporting in commerce, or importing any dead, dying, disabled or diseased animals or parts of the carcasses...

9 CFR 325.20 - Transportation and other transactions concerning dead, dying, disabled, or diseased livestock...

Code of Federal Regulations, 2013 CFR

2013-01-01

... concerning dead, dying, disabled, or diseased livestock, and parts of carcasses of livestock that died... other transactions concerning dead, dying, disabled, or diseased livestock, and parts of carcasses of... transporting in commerce, or importing any dead, dying, disabled or diseased animals or parts of the carcasses...

Matched metal die compression molded structural random fiber sheet molding compound flywheel

DOEpatents

Kulkarni, Satish V.; Christensen, Richard M.; Toland, Richard H.

1985-01-01

A flywheel (10) is described that is useful for energy storage in a hybrid vehicle automotive power system or in some stationary applications. The flywheel (10) has a body of essentially planar isotropic high strength structural random fiber sheet molding compound (SMC-R). The flywheel (10) may be economically produced by a matched metal die compression molding process. The flywheel (10) makes energy intensive efficient use of a fiber/resin composite while having a shape designed by theory assuming planar isotropy.

Living through the end: The phenomenon of dying at home.

PubMed

Solomon, Diane N; Hansen, Lissi

2015-04-01

To explore the unique lived experiences of one patient who died at home and her family members, and to interpret how dying at home influenced patterns of bereavement for this patient's family. Benner's (1985) interpretive phenomenological approach was employed to get at the embedded nature of the social phenomenon of dying at home, uncovering what may be taken for granted by participants - in this case, during and after the patient's home hospice course. The participants were a 78-year-old female diagnosed with amyotrophic lateral sclerosis six months prior to death, her husband, and three of her four children. In line with the patient's wish to die at home, she voluntarily forewent food and drink when she no longer wished to watch her body deteriorate and felt that her life had run its course. She informed her family of this plan, and all were supportive. For data collection, separate single in-depth interviews were conducted with the deceased three months prior to death, and after death with three of her four children and her spouse of 60 years. For data analysis, the interview transcripts were coded for paradigm cases, exemplars, and themes. The paradigm case, "The Meaning of Being at Home," revealed that for study participants, remaining home with hospice provided a richly familiar, quiet, and safe environment for being together over time and focusing on relationships. Exemplars included "Driving Her Own Course" and "Not Being a Burden." Salient themes encompassed patient and family characteristics, support, emotions, the value of time, and aspects of the healthcare team. End-of-life care providers need to hold a patient-centered, family-focused view to facilitate patient and family wishes to remain home to die. Investigation into family relationships, from the perspectives of both patient and family members, longitudinally, may enrich understanding and ability and help patients to die at home.

Death and Dying Anxiety among Elderly Arab Muslims in Israel

ERIC Educational Resources Information Center

Azaiza, Faisal; Ron, Pnina; Shoham, Meyrav; Gigini, Ibrahim

2010-01-01

Death and dying anxiety were examined among elderly Arab Muslims in Israel. A total of 145 people aged 60 and over were interviewed using a standardized questionnaire. Nursing home residents reported higher death anxiety than others; women and uneducated participants reported greater levels of fear of death and dying than others. There were no…

Smartes System für die Energiewende - der Übertragungsnetzbetreiber in der digitalen Zukunft

NASA Astrophysics Data System (ADS)

Pflaum, Rainer; Egeler, Tobias

Die Übertragungsnetze stellen eine zuverlässige Versorgung von Haushalt, Gewerbe und Industrie mit elektrischer Energie sicher und sind damit Grundlage einer modernen Wirtschaft und Gesellschaft. Die mittlerweile unumkehrbaren Entwicklungen der nationalen und europäischen Energiewende stellen den Übertragungsnetzbetreiber in seinen Kernaufgaben, dem Bau und Betrieb von Netzen, dem Markt- und Netzzugang und der Integration der erneuerbaren Energien vor neue und große Herausforderungen. Verbrauchsnahe dezentrale Erzeugung wie verbrauchsferne zentrale Erzeugung muss im Sinne der Gewährleistung der Systemstabilität gemanagt und in Einklang mit dem Verbrauch gebracht werden. Erneuerbare Energien müssen zudem in einem solchen System ihren Beitrag zur System- und Marktintegration leisten. All das erfordert mehr Daten, um in einem Gesamtsystem dynamische Reaktionsmöglichkeiten gewährleisten zu können. Erst die "Digitalisierung" schafft dabei die notwendigen Voraussetzungen die Komplexität zu stemmen. Die Digitalisierung stellt daher ein Kernelement dieses Wandels des Übertragungsnetzbetreibers dar, die einerseits mit zum Entstehen der neuen Herausforderungen beiträgt, andererseits aber auch hilft Werkzeuge bereitzustellen, diesen Herausforderungen zu begegnen. Im folgenden Beitrag wird aufgezeigt, wie die Digitalisierung die Aufgaben und Instrumente des Übertragungsnetzbetreibers verändern. Ausgehend von den heutigen Aufgaben eines Übertragungsnetzbetreibers und dem gültigen Rechtsrahmen werden unter dem Begriff "Notwendiges Set für morgen" smarte Elemente und Werkzeuge beschrieben, die bereits heute im Einsatz sind oder in den nächsten Jahren notwendig werden. Im Anschluss erfolgt anhand einiger Beispiele aus unterschiedlichen Bereichen eine Konkretisierung der Einsatzzwecke der Digitalisierung beim Übertragungsnetzbetreiber. Ein kurzer Ausblick mit Fokus auf den weiteren Veränderungsprozess rundet den Beitrag ab.

Die Deutsche Statistische Gesellschaft in der Weimarer Republik und während der Nazidiktatur

NASA Astrophysics Data System (ADS)

Wilke, Jürgen

Nach anfänglichen Schwierigkeiten durch den 1. Weltkrieg erlangte die Deutsche Statistische Gesellschaft (DStatG) unter dem renommierten Statistiker und Vorsitzenden der DStatG, Friedrich Zahn, durch eine Vielzahl von Aktivitäten hohes Ansehen. Es gab Bestrebungen, Statistiker aus allen Arbeitsfeldern der Statistik in die DStatG zu integrieren, wobei die "Mathematische Statistik" nur zögerlich akzeptiert wurde (Konjunkturforschung, Zeitreihenanalyse). Nach der Machtübernahme 1933 durch Adolf Hitler geriet die DStatG in das Fahrwasser nationalsozialistischer Ideologie und Politik (Führerprinzip, Gleichschaltung des Vereinswesens). Damit war eine personelle Umstrukturierung in der DStatG verbunden. Politisch Missliebige und rassisch Verfolgte mussten die DStatG verlassen (Bernstein, Freudenberg, Gumbel u.a.). Unter den Statistikern gab es alle Abstufungen im Verhalten zum Regime von Ablehnung und zwangsweiser Anpassung über bereitwilliges Mitläufertum bis zu bewusster Täterschaft. Besonders die Bevölkerungsstatistik wurde durch die NS- Rassenpolitik auf lange Sicht diskreditiert. Im Rahmen von Wirtschaftsplanung und Aufrüstung wurden neue zukunftsträchtige statistische Modelle (Grünig, Bramstedt, Leisse) entwickelt.

Enhancing Impact Speed with Shock Interactions in a Restricting Die

NASA Astrophysics Data System (ADS)

Anderson, William; Jensen, Brian; Cherne, Frank; Owens, Charles; Ramos, Kyle; Lieber, Mark

2013-06-01

There is a need to increase the impact velocities that can be achieved with gun systems used for impact and shock compression studies. Two-stage guns normally required for high-velocity studies are expensive and relatively rare, while most single-stage guns have modest performance (0.2-2 km/s) that limits their utility for high-pressure and high-velocity studies. In this work, we are developing a technique that uses a low-strength sabot, coupled with a restricting die, to increase the impact velocity without modifying the gun itself. Impact of the projectile with the die, which is typically attached to the muzzle of the gun, generates shock waves in the sabot that interact to accelerate the front of the projectile, while decelerating the rear portion. The performance achieved by this technique is greater than would be expected from a simple nozzle working on a fluid with the properties of the sabot. Preliminary experiments using this technique have observed a velocity enhancement of close to a factor of two. The performance that can be achieved is critically dependent on the stress field geometry and we are currently developing a set of models and calculations to optimize this system. Work performed under DOE Contract DE-AC52-06NA25396.

The Onion and "When Legends Die."

ERIC Educational Resources Information Center

Bell, Loren C.

1984-01-01

Describes the eight layers in Thomas Black Bull's ("When the Legends Die") journey to spiritual rebirth and stresses that students can easily identify these layers and can thereby achieve a clearer understanding of the relationship between structure and meaning in fiction. (CRH)

Living with Dying in the Pediatric Intensive Care Unit: A Nursing Perspective.

PubMed

Stayer, Debbie; Lockhart, Joan Such

2016-07-01

Despite reported challenges encountered by nurses who provide palliative care to children, few researchers have examined this phenomenon from the perspective of nurses who care for children with life-threatening illnesses in pediatric intensive care units. To describe and interpret the essence of the experiences of nurses in pediatric intensive care units who provide palliative care to children with life-threatening illnesses and the children's families. A hermeneutic phenomenological study was conducted with 12 pediatric intensive care unit nurses in the northeastern United States. Face-to-face interviews and field notes were used to illuminate the experiences. Five major themes were detected: journey to death; a lifelong burden; and challenges delivering care, maintaining self, and crossing boundaries. These themes were illuminated by 12 subthemes: the emotional impact of the dying child, the emotional impact of the child's death, concurrent grieving, creating a peaceful ending, parental burden of care, maintaining hope for the family, pain, unclear communication by physicians, need to hear the voice of the child, remaining respectful of parental wishes, collegial camaraderie and support, and personal support. Providing palliative care to children with life-threatening illnesses was complex for the nurses. Findings revealed sometimes challenging intricacies involved in caring for dying children and the children's families. However, the nurses voiced professional satisfaction in providing palliative care and in support from colleagues. Although the nurses reported collegial camaraderie, future research is needed to identify additional supportive resources that may help staff process and cope with death and dying. ©2016 American Association of Critical-Care Nurses.

Archaeometric study on minting dies produced under papal rule in Ferrara

NASA Astrophysics Data System (ADS)

Monticelli, Cecilia; Balbo, Andrea; Vaccaro, Carmela; Gulinelli, Maria Teresa; Garagnani, Gian Luca

2013-12-01

In the Civic Museum of Palazzo Schifanoia in Ferrara, a collection of 1104 coin striking tools is stored. Among these, eight steel dies produced from the 2nd decade of the seventeenth to the half of the eighteenth century, representative of the whole period of activity of the papal mint in Ferrara, have been chosen and studied. In that period, while important innovations in the coin minting technique were introduced in Europe, Ferrara declined from the rank of ducal mint to that of peripheral minting center of the highly centralized Papal States. The dies have been characterized by metallographic, chemical, and microhardness investigations. The results suggest that the dies were obtained by a manual smithing technique consisting in hammer hot forging. The die quality improved with time. In fact, in the period 1619-1622, a hardening treatment for the engraved die end consisting in a simple local carburization coexisted with a more efficient production method, based on the application of a proper final heat treatment. This treatment induced a graded microstructure from the engraved end, with a hard martensitic or bainitic structure, to the opposite end, with a tough ferritic/pearlitic structure. From 1675 onward, the latter production method was applied on all the studied dies. The chemical analysis of the alloys suggest that they were likely obtained from iron ores with a common provenance, while the analysis of the slag inclusions suggests the adoption of a direct method of ironmaking throughout the activity period of the mint.

In the business of dying: questioning the commercialization of hospice.

PubMed

Perry, Joshua E; Stone, Robert C

2011-01-01

This article critically questions the commercialization of hospice care and the ethical concerns associated with the industry's movement toward "market-driven medicine" at the end of life. For example, the article examines issues raised by an influx of for-profit hospice providers whose business model appears at its core to have an ethical conflict of interest between shareholders doing well and terminal patients dying well. Yet, empirical data analyzing the experience of patients across the hospice industry are limited, and general claims that end-of-life patient care is inferior among for-profit providers or even that their business practices are somehow unseemly when compared to nonprofit providers cannot be substantiated. In fact, non-profit providers are not immune to potentially conflicting concerns regarding financial viability (i.e., "no margin, no mission"). Given the limitations of existing empirical data and contrasting ideological commitments of for-profit versus non-profit providers, the questions raised by this article highlight important areas for reflection and further study. Policymakers and regulators are cautioned to keep ethical concerns in the fore as an increasingly commercialized hospice industry continues to emerge as a dominant component of the U.S. health care system. Both practitioners and researchers are encouraged to expand their efforts to better understand how business practices and commercial interests may compromise the death process of the patient and patient's family--a process premised upon a philosophy and ethical tradition that earlier generations of hospice providers and proponents established as a trusted, end-of-life alternative. © 2011 American Society of Law, Medicine & Ethics, Inc.

U.S. Fruit and Vegetable Processing Industries.

ERIC Educational Resources Information Center

Buckley, Katharine C.; And Others

Because of shifts in consumer tastes and preferences, demographics, technology, government regulation, and the expanding interdependence of world markets, the United States fruit and vegetable processing industries must operate in a constantly changing and uncertain economic environment. U.S. per capita use of processed fruits and vegetables is…

Dying cancer patients talk about euthanasia.

PubMed

Eliott, Jaklin A; Olver, Ian N

2008-08-01

Within developed nations, there is increasing public debate about and apparent endorsement of the appropriateness of euthanasia as an autonomous choice to die in the face of intolerable suffering. Surveys report socio-demographic differences in rates of acceptance of euthanasia, but there is little in-depth analysis of how euthanasia is understood and positioned within the social and moral lives of individuals, particularly those who might be considered suitable candidates-for example, terminally-ill cancer patients. During discussions with 28 such patients in Australia regarding medical decisions at the end of life, euthanasia was raised by 13 patients, with the others specifically asked about it. Twenty-four patients spoke positively of euthanasia, 19 of these voicing some concerns. None identified euthanasia as a currently favoured option. Four were completely against it. Endorsement for euthanasia was in the context of a hypothetical future or for a hypothetical other person, or temporally associated with acute pain. Arguments supporting euthanasia framed the issue as a matter of freedom of choice, as preserving dignity in death, and as curbing intolerable pain and suffering, both of the patient and of those around them. A common analogy featured was that of euthanising a dog. These arguments were typically presented as self-evident justification for euthanasia, construed as an appropriate choice to die, with opposers positioned as morally inferior or ignorant. The difficulties of ensuring 'choice' and the moral connotations of 'choosing to die,' however, worked to problematise the appropriateness of euthanising specific individuals. We recommend further empirical investigation of the moral and social meanings associated with euthanasia.

Resilience and vulnerability: prolonged grief in the bereaved spouses of marital partners who died of AIDS.

PubMed

Yu, Nancy Xiaonan; Chan, Cecilia L W; Zhang, Jianxin; Stewart, Sunita M

2016-01-01

Spousal bereavement is closely linked to prolonged grief, that is, significant adjustment symptoms that last for more than six months after the loss. This article focused on potential risk and protective factors that may influence bereavement outcomes. Participants in this study were surviving spouses of individuals who died of acquired immune deficiency syndrome (AIDS). These participants were themselves living with human immunodeficiency syndrome. In this cross-sectional study, 120 bereaved participants completed measures of grief, quality of dying and death of the deceased, negative conceptions of death resulting from AIDS, death attitudes, and personal resilience. The results showed that one-third (35.0%) of the bereaved participants reported grief levels above the prolonged grief cut-off scores, and can be categorized as the "prolonged grief" group. Although quality of dying and death was not associated with the intensity of grief, negative conceptions of death from AIDS, fear of death and resilience independently predicted grief symptoms in the regression models. Our findings provide insight into the grief process for the surviving spouse of AIDS victims in rural China. Since resilience is malleable, developing resilience interventions to enhance adjustment to bereavement may be a promising direction in grief counselling and therapies.

Dying and the Conspiracy of Denial

ERIC Educational Resources Information Center

Doherty, Gillian; Doherty, Joseph

1976-01-01

The first author presents her reviews on death based on her experiences as a nurse and a wife whose husband had a terminal illness. The second author presents a poem expressing his views on death while he was dying of a terminal illness. (HLM)

Characteristics of Chinese Rural Young Suicides Who Did Not Have a Strong Intention to Die1

PubMed Central

Sun, Long; Zhang, Jie

2014-01-01

Background In exploration of the risk factors of the Chinese rural young suicide, previous researchers found low prevalence of mental problems, high degree of impulsivity, and great proportion of lethal pesticide consumption. It noticed that some of the young suicides in rural China did not intend to die from the suicidal behavior which was only instrumentally used for certain gains. Aims This study aims to look into the characteristics of those young suicides who did not really intend to die and compare them with those young suicides who had a strong intent to die. Methods Subjects were 386 suicides aged 15-34 years in the rural areas of three provinces in China. The data were obtained by psychological autopsy method. The degree of suicidal intent of the subjects was evaluated by the first 8 items of Beck’s Suicide Intent Scale (SIS). Results It was found that those suicides who had a strong intent of death were more likely to have higher age, more years of education, live alone, and suffer mental disease. On the other hand, the low intent suicides were more likely to have pesticides at home and to be impulsive. In other words, pesticides and impulsivity killed some Chinese rural young men and women who did not really want to die by suicide. Conclusion Findings of the study may be translated into practical measures in suicide prevention in China as well as elsewhere in the world. PMID:25497170

Noncanonical autophagy inhibits the auto-inflammatory, lupus-like response to dying cells

PubMed Central

Martinez, Jennifer; Cunha, Larissa D.; Park, Sunmin; Yang, Mao; Lu, Qun; Orchard, Robert; Li, Quan-Zhen; Yan, Mei; Janke, Laura; Guy, Cliff; Linkermann, Andreas; Virgin, Herbert W.; Green, Douglas R.

2016-01-01

Defects in dying cell clearance are postulated to underlie the pathogenesis of systemic lupus erythematosus (SLE)1. Mice lacking molecules associated with dying cell clearance develop SLE-like disease2, and phagocytes from SLE patients often display defective clearance and increased inflammatory cytokine production when exposed to dying cells in vitro. Previously, we3–6 and others7 described a form of noncanonical autophagy called “LC3-associated phagocytosis” (LAP), wherein phagosomes containing engulfed particles, including dying cells3,4,7, recruit elements of the autophagy pathway to facilitate phagosome maturation and digestion of cargo. Genome-wide association studies have identified polymorphisms in atg58 and possibly atg79, involved in both canonical autophagy and LAP3–7, as predisposition markers for SLE. Here, we describe the consequences of defective LAP in vivo. Mice lacking any of several components of the LAP pathway display elevated serum inflammatory cytokines, autoantibodies, glomerular immune complex deposition, and evidence of kidney damage. Dying cells, injected into LAP-deficient animals, are engulfed but not efficiently degraded, and trigger acute elevation of pro-inflammatory cytokines but not the anti-inflammatory interleukin (IL)-10. Repeated injection of dying cells into LAP-deficient, but not LAP-sufficient animals accelerated SLE-like disease, including increased serum levels of autoantibodies. In contrast, animals deficient for genes required for canonical autophagy but not LAP do not display defective dead cell clearance, inflammatory cytokine production, or SLE-like disease, and like wild-type animals, produce IL-10 in response to dying cells. Therefore, defects in LAP, rather than canonical autophagy, can cause SLE-like phenomena, and may contribute to the pathogenesis of SLE. PMID:27096368

Health Care Providers and Dying Patients: Critical Issues in Terminal Care.

ERIC Educational Resources Information Center

Benoliel, Jeanne Quint

1988-01-01

Identifies three major areas of concern in relationship between health care providers and dying patients: (1) nature of difficulties and stresses associated with terminal care; (2) education of providers for work; and (3) influence of organizational structure and institutionalized values on services for dying patients and families. Reviews…

Die-target for dynamic powder consolidation

DOEpatents

Flinn, John E.; Korth, Gary E.

1986-01-01

A die/target is disclosed for consolidation of a powder, especially an atomized rapidly solidified metal powder, to produce monoliths by the dynamic action of a shock wave, especially a shock wave produced by the detonation of an explosive charge. The die/target comprises a rectangular metal block having a square primary surface with four rectangular mold cavities formed therein to receive the powder. The cavities are located away from the geometrical center of the primary surface and are distributed around such center while also being located away from the geometrical diagonals of the primary surface to reduce the action of reflected waves so as to avoid tensile cracking of the monoliths. The primary surface is covered by a powder retention plate which is engaged by a flyer plate to transmit the shock wave to the primary surface and the powder. Spawl plates are adhesively mounted on other surfaces of the block to act as momentum traps so as to reduce reflected waves in the block.

The s-process in massive stars: the Shell C-burning contribution

NASA Astrophysics Data System (ADS)

Pignatari, Marco; Gallino, R.; Baldovin, C.; Wiescher, M.; Herwig, F.; Heger, A.; Heil, M.; Käppeler, F.

In massive stars the s¡ process (slow neutron capture process) is activated at different tempera- tures, during He¡ burning and during convective shell C¡ burning. At solar metallicity, the neu- tron capture process in the convective C¡ shell adds a substantial contribution to the s¡ process yields made by the previous core He¡ burning, and the final results carry the signature of both processes. With decreasing metallicity, the contribution of the C¡ burning shell to the weak s¡ process rapidly decreases, because of the effect of the primary neutron poisons. On the other hand, also the s¡ process efficiency in the He core decreases with metallicity.

Why do we want the right to die? A systematic review of the international literature on the views of patients, carers and the public on assisted dying.

PubMed

Hendry, Maggie; Pasterfield, Diana; Lewis, Ruth; Carter, Ben; Hodgson, Daniel; Wilkinson, Clare

2013-01-01

Assisted dying is legal in four European countries and three American states. Elsewhere, particularly in more affluent or mainly Protestant countries, it remains controversial. Dominant headlines feature professional (medical, legal, religious) arguments versus celebrity campaigners; ordinary people are less clearly represented. To synthesise the international evidence of people's views and attitudes towards assisted dying in order to inform current debate about this controversial issue. Systematic review and mixed method synthesis of qualitative and survey data. Eleven electronic databases from inception to October 2011; bibliographies of included studies. Two reviewers independently screened papers and appraised quality. Qualitative results were extracted verbatim; survey results were summarised in a table. Qualitative data were synthesised using framework methods and survey results integrated where they supported, contrasted or added to the themes identified. Sixteen qualitative studies and 94 surveys were included; many participants considered the immediate relevance of assisted dying for them. Themes related to poor quality of life, a good quality of death, potential abuse of assisted dying and the importance of individual stance. People valued autonomy in death as much as in life. Attitudes were diverse, complex and related to definitions of unbearable suffering including physical, psycho-social and existential factors and were consistent regardless of social, economic, legal and health-care contexts. Our review sheds light on ordinary people's perspectives about assisted dying, when they are ill or disabled. Unbearable suffering is a key construct, and common factors are revealed that lead people to ask for help to die. The consistency of international views indicates a mandate for legislative and medical systems worldwide to listen and understand this.

Death and Dying in Modern America

ERIC Educational Resources Information Center

Feifel, Herman

1977-01-01

Appreciation of finiteness, of our temporal character, can serve not only to enrich self-knowledge but also to provide the momentum to propel us forward toward productivity, achievement, and creativity. Presented at the Conference on Death and Dying: Education, Counseling, and Care, December 1-3, 1976, Orlando, Florida. (Author)

Is the patient's right to die evolving into a duty to die?: Medical decision making and ethical evaluations in health care.

PubMed

Sprung, C L; Eidelman, L A; Steinberg, A

1997-02-01

When patient or family requests for continued life-sustaining treatments conflict with doctor recommendations, different conclusions as to what is beneficial for the patient may arise. Past practices usually accepted patient or family requests based on the principle of autonomy or that the doctor's primary responsibility is to the individual patient. Many patients die in intensive care units after doctors forego life-prolonging interventions. Health care changes and cost containment have led to a change in the classical ethical model of the patient-doctor relationship such that concerns for societal requirements increasingly overrule those for individual patient needs. The ability to keep patients alive with little likelihood of recovery and the recognition of escalating health costs have led to calls for the needs of society and distributive justice to be taken into account. A tendency to justify a duty to die for these patients has arisen. Recent legal decisions in cases with conflicts between families and health care providers and institutions over foregoing life-sustaining therapies have decided for the families against doctors and hospitals, compelling institutions and their staff to act contrary to their ethical views. Value judgments of doctors are sometimes confused with medical indications for therapy. Doctors have defined therapies as futile or non-beneficial based on their own values and even withdrawn life-sustaining treatments without patient or family input. In some cases, the right to die is leading to the duty to die even against patient or surrogate wishes. Such observations indicate the need for rigorous analyses of medical decision making in this context and for ethical evaluations in health care in general.

Understanding the Problems of Death and Dying: A Health Professionals' Attitude Survey.

ERIC Educational Resources Information Center

Green, Joseph S.; And Others

1978-01-01

Attitudes of health practitioners and others toward death and dying and their emotional reactions to dying patients were surveyed both before and after a Veterans Administration workshop. Some attitude changes were noted, with implications for future workshops. (MF)

Shear zone formation within the billet and metal flow through the die orifice in unlubricated axisymmetric forward and backward extrusion

NASA Astrophysics Data System (ADS)

Valberg, Henry; Costa, Andrè L. M.

2017-10-01

Metal flow inside the billet is known to be completely different in forward (FWE) and backward (BWE) Al-extrusion. A practical implication of this is that contamination near to the surface of the extrusion billet, or on the peripheral surface skin, tends to flow out of the die more readily in BWE than in FWE. It is therefore common in BWE to use a scalping operation on the billet to remove eventual sub-surface contamination that may be present. This additional working operation may be required in order to avoid surface quality problems on BWE profiles. In spite of the importance of metal flow in metals extrusion, there are still lack of knowledge about the topic. With recent progress in FEM-analysis for modelling deformation processing, however, it is now possible to perform accurate studies on metal flow phenomena by simulation on the computer. In our study, we are using the 3D FEM-program DEFORM® to model axisymmetric FWE and BWE in case of non-lubricated extrusion through a flat-faced die. Our primary focus is to consider the difference in appearance of shear zones present inside the extrusion billet for the two processes, including metal flow in the die mouth.

A fast discrete S-transform for biomedical signal processing.

PubMed

Brown, Robert A; Frayne, Richard

2008-01-01

Determining the frequency content of a signal is a basic operation in signal and image processing. The S-transform provides both the true frequency and globally referenced phase measurements characteristic of the Fourier transform and also generates local spectra, as does the wavelet transform. Due to this combination, the S-transform has been successfully demonstrated in a variety of biomedical signal and image processing tasks. However, the computational demands of the S-transform have limited its application in medicine to this point in time. This abstract introduces the fast S-transform, a more efficient discrete implementation of the classic S-transform with dramatically reduced computational requirements.

Membrane-bound heat shock proteins facilitate the uptake of dying cells and cross-presentation of cellular antigen.

PubMed

Zhu, Haiyan; Fang, Xiaoyun; Zhang, Dongmei; Wu, Weicheng; Shao, Miaomiao; Wang, Lan; Gu, Jianxin

2016-01-01

Heat shock proteins (HSPs) were originally identified as stress-responsive proteins and serve as molecular chaperones in different intracellular compartments. Translocation of HSPs to the cell surface and release of HSPs into the extracellular space have been observed during the apoptotic process and in response to a variety of cellular stress. Here, we report that UV irradiation and cisplatin treatment rapidly induce the expression of membrane-bound Hsp60, Hsp70, and Hsp90 upstream the phosphatidylserine exposure. Membrane-bound Hsp60, Hsp70 and Hsp90 could promote the release of IL-6 and IL-1β as well as DC maturation by the evaluation of CD80 and CD86 expression. On the other hand, Hsp60, Hsp70 and Hsp90 on cells could facilitate the uptake of dying cells by bone marrow-derived dendritic cells. Lectin-like oxidized LDL receptor-1 (LOX-1), as a common receptor for Hsp60, Hsp70, and Hsp90, is response for their recognition and mediates the uptake of dying cells. Furthermore, membrane-bound Hsp60, Hsp70 and Hsp90 could promote the cross-presentation of OVA antigen from E.G7 cells and inhibition of the uptake of dying cells by LOX-1 decreases the cross-presentation of cellular antigen. Therefore, the rapid exposure of HSPs on dying cells at the early stage allows for the recognition by and confers an activation signal to the immune system.

Evolve or Die: The U.S. Army’s Darwinian Challenge

DTIC Science & Technology

2013-05-23

5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Lieutenant Colonel Todd A. Schmidt 5d...class of SAMS students, Major General Edward Cardon , Commanding General of the 2nd Infantry Division in South Korea, stated that the expectations of...uncertainty, capable of developing and leading concepts for change. “Transitions are the most important events you will have to manage,” Cardon stated

U.S. coral reefs; imperiled national treasures

USGS Publications Warehouse

Field, M.E.; Cochran, S.A.; Evans, K.R.

2002-01-01

Coral reefs are home to 25% of all marine species. However, the tiny colonial animals that build these intricate limestone masses are dying at alarming rates. If this trend continues, in 20 years the living corals on many of the world's reefs will be dead and the ecosystems that depend on them severely damaged. As part of the effort to protect our Nation's extensive reefs, U.S. Geological Survey (USGS) scientists are working to better understand the processes that affect the health of these ecologically and economically important ecosystems.

To Die, To Sleep: A Contrastive Study of Metaphors for Death and Dying in English and Spanish.

ERIC Educational Resources Information Center

Marin-Arrese, Juana I.

1996-01-01

Contrasts the use of metaphors for death and dying in English and Spanish and makes some observations concerning universal and culture-specific conceptualizations. The article points out that the human capacity to conceptualize and reason derives from experience (perceptions, cultural practices, motor activity) and imagination (metaphor, metonymy,…

Counseling Older Persons: Careers, Retirement, Dying.

ERIC Educational Resources Information Center

Sinick, Daniel

The focus of this monograph is on three areas of counseling with older clients: career counseling, retirement counseling, and counseling regarding death and dying. The portion on career counseling includes reasons older persons change careers, obstacles they are likely to face when seeking employment, myths surrounding the employability of older…

Characterization of 16S rRNA Processing with Pre-30S Subunit Assembly Intermediates from E. coli.

PubMed

Smith, Brian A; Gupta, Neha; Denny, Kevin; Culver, Gloria M

2018-06-08

Ribosomal RNA (rRNA) is a major component of ribosomes and is fundamental to the process of translation. In bacteria, 16S rRNA is a component of the small ribosomal subunit and plays a critical role in mRNA decoding. rRNA maturation entails the removal of intervening spacer sequences contained within the pre-rRNA transcript by nucleolytic enzymes. Enzymatic activities involved in maturation of the 5'-end of 16S rRNA have been identified, but those involved in 3'-end maturation of 16S rRNA are more enigmatic. Here, we investigate molecular details of 16S rRNA maturation using purified in vivo-formed small subunit (SSU) assembly intermediates (pre-SSUs) from wild-type Escherichia coli that contain precursor 16S rRNA (17S rRNA). Upon incubation of pre-SSUs with E. coli S100 cell extracts or purified enzymes implicated in 16S rRNA processing, the 17S rRNA is processed into additional intermediates and mature 16S rRNA. These results illustrate that exonucleases RNase R, RNase II, PNPase, and RNase PH can process the 3'-end of pre-SSUs in vitro. However, the endonuclease YbeY did not exhibit nucleolytic activity with pre-SSUs under these conditions. Furthermore, these data demonstrate that multiple pathways facilitate 16S rRNA maturation with pre-SSUs in vitro, with the dominant pathways entailing complete processing of the 5'-end of 17S rRNA prior to 3'-end maturation or partial processing of the 5'-end with concomitant processing of the 3'-end. These results reveal the multifaceted nature of SSU biogenesis and suggest that E. coli may be able to escape inactivation of any one enzyme by using an existing complementary pathway. Copyright © 2018 Elsevier Ltd. All rights reserved.

Are religiousness and death attitudes associated with the wish to die in older people?

PubMed

Bonnewyn, Anke; Shah, Ajit; Bruffaerts, Ronny; Demyttenaere, Koen

2016-03-01

A wish to die is common in older persons and is associated with increased mortality. Several risk factors have been identified, but the association between religiousness and a wish to die in older adults has been underexplored, and the association between death attitudes and the presence of a wish to die has not been investigated yet. The aim of this study is to explore the relationship between religiousness and death attitudes on the one hand and wish to die on the other hand, adjusting for clinical factors such as the presence of depression or somatic disorder. The sample comprised 113 older inpatients (from a psychiatric and somatic ward) with a mean age of 74 years. Psychiatric diagnoses were assessed by the Structured Clinical Interview for DSM-IV Disorders, and logistic regression analyses estimated the unique contribution of religiousness and death attitudes to the wish to die, controlling for socio-demographic variables, depressive disorder, and somatic symptoms. Both religiousness and death attitudes were associated with a wish to die in univariate models. Adding these variables in a multivariate logistic hierarchical model, death attitudes remained significant predictors but religiousness did not; 55% of the pseudovariance of the wish to die was explained by these variables, with an effective size of 0.89. Major depressive episode, somatic symptoms, Fear of Death, and Escape Acceptance were the most important predictors of the wish to die. This study suggests that how older adults perceive death partly determines whether they have a wish to die. There may be a clinical, patient-oriented benefit in discussing with older patients about how they perceive death, as this can play a role in the early detection (and prevention) of death or suicide ideation and associated behaviors in older adults.

ATM experiment S-056 image processing requirements definition

NASA Technical Reports Server (NTRS)

1972-01-01

A plan is presented for satisfying the image data processing needs of the S-056 Apollo Telescope Mount experiment. The report is based on information gathered from related technical publications, consultation with numerous image processing experts, and on the experience that was in working on related image processing tasks over a two-year period.

Attitudes and experiences of nurses toward death and caring for dying patients in Turkey.

PubMed

Cevik, Banu; Kav, Sultan

2013-01-01

Caring of the dying patients and facing the death can be a stressful and difficult experience for nurses. Besides personal and professional experiences, nurses' own attitudes toward death may affect the care given to dying individuals. The aim of this study was to examine Turkish nurses' attitudes toward and experiences with death and caring for dying patients. A descriptive, cross-sectional study was conducted at 2 university hospitals and 1 state hospital located in Ankara, Turkey. Data were collected via sociodemographics form, the Death Attitude Profile-Revised, and Frommelt's Attitude Toward Caring for Dying Patients. The attitudes of Turkish nurses toward death and caring for dying patients are less positive than the reported attitudes of nurses in other studies. Significant relationships were found among level of education, willingness to care for dying patients, and scores on Frommelt's Attitude Toward Caring for Dying Patients and on Death Attitude Profile-Revised subscales (P < .05). Although the majority of nurses (85%) stated that they had received education on end of life, most of them (82%) were not comfortable talking about death. A lack of education and experience may contribute to the negative attitudes. Providing a reflective narrative environment in which nurses can express their personal feelings about death and dying could be a potentially effective approach. This study highlights the need for further educational research and development of better educational programs to help nurses to explore and understand their attitudes toward death, overcome fears, increase communication skills, and enhance coping strategies.

Influence of the supporting die structures on the fracture strength of all-ceramic materials.

PubMed

Yucel, Munir Tolga; Yondem, Isa; Aykent, Filiz; Eraslan, Oğuz

2012-08-01

This study investigated the influence of the elastic modulus of supporting dies on the fracture strengths of all-ceramic materials used in dental crowns. Four different types of supporting die materials (dentin, epoxy resin, brass, and stainless steel) (24 per group) were prepared using a milling machine to simulate a mandibular molar all-ceramic core preparation. A total number of 96 zirconia cores were fabricated using a CAD/CAM system. The specimens were divided into two groups. In the first group, cores were cemented to substructures using a dual-cure resin cement. In the second group, cores were not cemented to the supporting dies. The specimens were loaded using a universal testing machine at a crosshead speed of 0.5 mm/min until fracture occurred. Data were statistically analyzed using two-way analysis of variance and Tukey HSD tests (α = 0.05). The geometric models of cores and supporting die materials were developed using finite element method to obtain the stress distribution of the forces. Cemented groups showed statistically higher fracture strength values than non-cemented groups. While ceramic cores on stainless steel dies showed the highest fracture strength values, ceramic cores on dentin dies showed the lowest fracture strength values among the groups. The elastic modulus of the supporting die structure is a significant factor in determining the fracture resistance of all-ceramic crowns. Using supporting die structures that have a low elastic modulus may be suitable for fracture strength tests, in order to accurately reflect clinical conditions.

The contribution of a MOOC to community discussions around death and dying.

PubMed

Tieman, Jennifer; Miller-Lewis, Lauren; Rawlings, Deb; Parker, Deborah; Sanderson, Christine

2018-02-20

Advances in medicine have helped many to live longer lives and to be able to meet health challenges. However death rates are anticipated to increase given the ageing population and chronic disease progression. Being able to talk about death is seen to be important in normalising death as part of life and supporting preparedness for death. Massive Open Online Courses (MOOCs) provide opportunities for the community to engage in collaborative learning. A 5 week MOOC was developed covering four main topics (language and humour, representations of death, medicalisation of dying, and digital dying) aiming: To enable participants to openly and supportively discuss and learn about issues around living, death and dying, To explore the normally unheard opinions and views of Australians around death and dying, and To determine what effect online learning and discussions offered through the MOOC had on participants' feelings and attitudes towards death and dying. Data was captured on engagement rates in the various MOOC activities. Death Attitudes were measured by five items representing the MOOC's learning objectives and completed at enrolment and conclusion. MOOC Satisfaction was measured with six items at the end of the MOOC. Descriptive statistics were produced for each variable and Chi-Square Tests of Independence assessed the extent of the relationship between categorical variables. Socio-demographic variables were examined as predictors of the outcome variables of MOOC engagement, MOOC satisfaction, and death attitudes. Ethical approval was received from Flinders University Social and Behavioural Research Ethics Committee (Project No. 7247). One thousand one hundred fifty six people enrolled in the Dying2Learn MOOC with 895 participating in some way. Enrolees were primarily female (92.1%). Age ranged from 16 to 84 (mean = 49.5, SD = 12.3). MOOC satisfaction scores were high. Responses to the experience of participating in the MOOC were very positive, with mean

Wirkungen biogener Amine auf die Erregungs-Sekretions-Kopplung in der Speicheldrüse von Periplaneta americana (L.)

NASA Astrophysics Data System (ADS)

Rietdorf, Katja

2003-07-01

AMP und / oder cGMP erhöht und anschließend den Proteingehalt im Endspeichel gemessen. Ein Anstieg der intrazellulären Ca2+-Konzentration aktiviert nur eine geringe Rate der Proteinsekretion. Dagegen kann die Steigerung der intrazellulären cAMP-Konzentration eine stärkere Proteinsekretion aktivieren, die sich nicht signifikant von der nach 5-HT-Stimulierung unterscheidet. Die cAMP-stimulierte Proteinsekretion kann durch gleichzeitige Erhöhung der intrazellulären Ca2+-Konzentration weiter gesteigert werden. Dagegen aktivierte eine Erhöhung der intrazellulären cGMP-Konzentration die Proteinsekretion nicht. Aufgrund dieser Ergebnisse postuliere ich die Existenz eines die Adenylatcyclase aktivierenden 5-HT-Rezeptors in der Basolateralmembran der C-Zellen. The aim of this PhD-work was to investigate major mechanisms of excitation-secretion coupling in the salivary gland of the cockroach Periplaneta americana (L.). This salivary gland is innervated by dopaminergic and serotonergic fibres (Baumann et al., 2002). The two transmitters stimulate different processes in the gland: Dopamine (DA) stimulates the p-cells of the acini and the salivary duct cells, whereas 5-HT (serotonin) activates the p- and the c-cells of the acini, but not the salivary duct cells. Final saliva is completely protein-free after dopamine stimulation. It contains proteins, which are secreted by the c-cells of the acini, after a 5-HT-stimulation (Just & Walz, 1996). In the first part of my work I measured the electrolytic composition of the final saliva by capillary electrophoretic analysis and measured the rates of fluid secretion, in order to answer the following questions: 1.) Which transporters affect the production of primary saliva and its modification? 2.) What is the function of the transport-active salivary duct cells for the modification of the primary saliva? Electrolytic composition of the DA- and 5-HT-stimulated final saliva is not significantly different from each other, and is

Stamping Die Making. 439-318/320.

ERIC Educational Resources Information Center

Yunke, P.; And Others

Each unit in this curriculum guide on stamping die making contains an introduction, objectives, materials required, lessons, space for notes, figures, and diagrams. There are 29 units in this guide, dealing with the following topics: EZ-MILL programming; EZ-MILL BATT; print of punch and EZ-MILL part programming; download to Computer Numerical…

Constructing Death: Three Pathographies about Dying.

ERIC Educational Resources Information Center

Hawkins, Anne Hunsaker

1991-01-01

Discusses three pathographies as models for the "good death." In each, the author organizes the phenomena associated with the illness and death of a spouse from cancer into a coherent pattern. The result is three different paradigms of the experience of dying: "ritual death,""victorious death," and "one's own death." (Author/LLL)

Exploring the Contemporary Stage and Scripts for the Enactment of Dying Roles: A Narrative Review of the Literature.

PubMed

Lowrie, Daniel; Ray, Robin; Plummer, David; Yau, Matthew

2018-03-01

This narrative review explores the literature regarding the drama of dying from several academic perspectives. Three key themes were identified including "The impact of blurred boundaries on roles and transitions," "The orchestration of death and dying through time," and "Contemporary dying and new machinery of control." This review reveals the manner in which tightly scripted dying roles serve the needs of the living to a greater extent than those of the dying, by ensuring the depiction of both dying and death as phenomena which have been brought under the control of the living, thereby countering death anxiety. An incongruence between the actual experience of dying and contemporary dying scripts is also highlighted. The authors argue that this incongruence is hidden from the broader societal audience through the maintenance of a dying role that demands serenity and acceptance, thus downplaying or even hiding the actual end-of-life experiences of the dying themselves.

Living and dying: responsibility for end-of-life care in care homes without on-site nursing provision - a prospective study.

PubMed

Handley, Melanie; Goodman, Claire; Froggatt, Katherine; Mathie, Elspeth; Gage, Heather; Manthorpe, Jill; Barclay, Stephen; Crang, Clare; Iliffe, Steve

2014-01-01

The aim of the study was to describe the expectations and experiences of end-of-life care of older people resident in care homes, and how care home staff and the healthcare practitioners who visited the care home interpreted their role. A mixed-method design was used. The everyday experience of 121 residents from six care homes in the East of England were tracked; 63 residents, 30 care home staff with assorted roles and 19 National Health Service staff from different disciplines were interviewed. The review of care home notes demonstrated that residents had a wide range of healthcare problems. Length of time in the care homes, functional ability or episodes of ill-health were not necessarily meaningful indicators to staff that a resident was about to die. General Practitioner and district nursing services provided a frequent but episodic service to individual residents. There were two recurring themes that affected how staff engaged with the process of advance care planning with residents; 'talking about dying' and 'integrating living and dying'. All participants stated that they were committed to providing end-of-life care and supporting residents to die in the care home, if wanted. However, the process was complicated by an ongoing lack of clarity about roles and responsibilities in providing end-of-life care, doubts from care home and primary healthcare staff about their capacity to work together when residents' trajectories to death were unclear. The findings suggest that to support this population, there is a need for a pattern of working between health and care staff that can encourage review and discussion between multiple participants over sustained periods of time. © 2013 John Wiley & Sons Ltd.

Marginal adaptation of four inlay casting waxes on stone, titanium, and zirconia dies.

PubMed

Michalakis, Konstantinos X; Kapsampeli, Vassiliki; Kitsou, Aikaterini; Kirmanidou, Yvone; Fotiou, Anna; Pissiotis, Argirios L; Calvani, Pasquale Lino; Hirayama, Hiroshi; Kudara, Yukio

2014-07-01

Different inlay casting waxes do not produce copings with satisfactory marginal accuracy when used on different die materials. The purpose of this study was to evaluate the marginal accuracy of 4 inlay casting waxes on stone dies and titanium and zirconia abutments and to correlate the findings with the degree of wetting between the die specimens and the inlay casting waxes. The inlay casting waxes tested were Starwax (Dentaurum), Unterziehwachs (Bredent), SU Esthetic wax (Schuler), and Sculpturing wax (Renfert). The marginal opening of the waxes was measured with a stereomicroscope on high-strength stone dies and on titanium and zirconia abutments. Photographic images were obtained, and the mean marginal opening for each specimen was calculated. A total of 1440 measurements were made. Wetting between die materials and waxes was determined after fabricating stone, titanium, and zirconia rectangular specimens. A calibrated pipette was used to place a drop of molten wax onto each specimen. The contact angle was calculated with software after an image of each specimen had been made with a digital camera. Collected data were subjected to a 2-way analysis of variance (α=.05). Any association between marginal accuracy and wetting of different materials was found by using the Pearson correlation. The wax factor had a statistically significant effect both on the marginal discrepancy (F=158.31, P<.001) and contact angle values (F=68.09, P<.001). A statistically significant effect of the die material factor both on the marginal adaptation (F=503.47, P<.001) and contact angle values (F=585.02, P<.001) was detected. A significant correlation between the marginal accuracy and the contact angle values (Pearson=0.881, P=.01) was also found. Stone dies provided wax copings with the best marginal integrity, followed by titanium and zirconia abutments. Unterziehwachs (Bredent), wax produced the best marginal adaptation on different die materials. A significant correlation was found

Multicenter Retrospective Cohort Study of "Talk and Die" After Traumatic Brain Injury.

PubMed

Shibahashi, Keita; Sugiyama, Kazuhiro; Okura, Yoshihiro; Hoda, Hidenori; Hamabe, Yuichi

2017-11-01

Patients who "talk and die" after traumatic brain injury (TBI) are potentially salvageable. The reported incidences and risk factors for the "talk and die" phenomenon are conflicting and do not take into account recent improvements in trauma care. The aim of this study was to determine the incidences of "talk and die" after TBI in a modern trauma care system, as well as associated risk factors. We identified patients who experienced TBI (abbreviated injury scale 3-5) between 2004 and 2015 who talked on admission (i.e., their verbal component on the Glasgow Coma Scale was ≥3 on admission) using a nationwide trauma registry (the Japan Trauma Data Bank). The end point was in-hospital mortality. We compared patients who talked and died with those who talked and survived. During the study period, 236,698 patients were registered in the database. Of the 24,833 patients who were eligible for analysis, 956 (4.0%) patients subsequently died in the hospital. The in-hospital mortality rate significantly decreased over the past 12 years. Older age; male sex; a higher injury severity score; a lower Glasgow Coma Scale score; comorbidities (congestive heart failure, chronic kidney disease, liver cirrhosis, and hematologic disorders); hypotension on arrival; subdural hemorrhage; contusion; and vault fracture were independently associated with higher in-hospital mortality. Even in modern trauma care systems, some patients still talk and die after TBI. We identified certain risk factors in patients with TBI that elicit the requirement for close observation, even if these patients talk after TBI. Copyright © 2017 Elsevier Inc. All rights reserved.

MTMC’s Approach to Reengineering DoD’s Personal Property Business Process.

DTIC Science & Technology

1996-01-01

Logistics Management Institute MTMG’s Approach to Reengineering DoD’s Personal Property Business Process MT502MR2 Alfred H.. Beyer James E...concerns, as expressed by business owners, senior executives, and managers during meetings, telephone conversations, and in correspondence, regarding... Business Process MT502MR2 Alfred H. Beyer James E. Cotterman Prepared pursuant to Department of Defense Contract DASW01-95-C-0019. The views

Gesellschaft, Lebensgemeinschaft, Ökosystem - Über die Kongruenz von politischen und ökologischen Theorien der Entwicklung

NASA Astrophysics Data System (ADS)

Voigt, Annette

Im Jahr 1859 veröffentlichte Charles Darwin "On the Origin of Species“. Seine Evolutionstheorie ist das wohl spektakulärste Beispiel einer naturwissenschaftlichen Theorie großer gesellschaftlicher Relevanz. Ihre verschiedenen Facetten wurden in der Öffentlichkeit kontrovers diskutiert, unter anderem auch ihre Anwendung zur Erklärung von Zuständen und Prozessen menschlicher Gesellschaften. Zum Teil wurde die Seiensweise der Natur - scheinbar unabhängig von gesellschaftlichen Interessen - für die Erklärung und Legitimation gesellschaftlicher Zustände oder die Legitimation von politischen Ideologien herangezogen (Sozialdarwinismus). Denn Gesellschaft funktioniere ja so, wie Darwin die Natur erklärt habe: es herrsche z. B. Konkurrenzkampf, Auslese und Arbeitsteilung, Erfolg hätten diejenigen, die sich an die Bedingungen am Besten anpassten.

Defining a Good Death (Successful Dying): Literature Review and a Call for Research and Public Dialogue.

PubMed

Meier, Emily A; Gallegos, Jarred V; Thomas, Lori P Montross; Depp, Colin A; Irwin, Scott A; Jeste, Dilip V

2016-04-01

There is little agreement about what constitutes good death or successful dying. The authors conducted a literature search for published, English-language, peer-reviewed reports of qualitative and quantitative studies that provided a definition of a good death. Stakeholders in these articles included patients, prebereaved and bereaved family members, and healthcare providers (HCPs). Definitions found were categorized into core themes and subthemes, and the frequency of each theme was determined by stakeholder (patients, family, HCPs) perspectives. Thirty-six studies met eligibility criteria, with 50% of patient perspective articles including individuals over age 60 years. We identified 11 core themes of good death: preferences for a specific dying process, pain-free status, religiosity/spirituality, emotional well-being, life completion, treatment preferences, dignity, family, quality of life, relationship with HCP, and other. The top three themes across all stakeholder groups were preferences for dying process (94% of reports), pain-free status (81%), and emotional well-being (64%). However, some discrepancies among the respondent groups were noted in the core themes: Family perspectives included life completion (80%), quality of life (70%), dignity (70%), and presence of family (70%) more frequently than did patient perspectives regarding those items (35%-55% each). In contrast, religiosity/spirituality was reported somewhat more often in patient perspectives (65%) than in family perspectives (50%). Taking into account the limitations of the literature, further research is needed on the impact of divergent perspectives on end-of-life care. Dialogues among the stakeholders for each individual must occur to ensure a good death from the most critical viewpoint-the patient's. Copyright © 2016 American Association for Geriatric Psychiatry. Published by Elsevier Inc. All rights reserved.

Matched metal die compression molded structural random fiber sheet molding compound flywheel. [Patent application

DOEpatents

Kulkarni, S.V.; Christensen, R.M.; Toland, R.H.

1980-09-24

A flywheel is described that is useful for energy storage in a hybrid vehicle automotive power system or in some stationary applications. The flywheel has a body of essentially planar isotropic high strength structural random fiber sheet molding compound (SMC-R). The flywheel may be economically produced by a matched metal die compression molding process. The flywheel makes energy intensive efficient use of a fiber/resin composite while having a shape designed by theory assuming planar isotropy.

Dying with dignity: a concept analysis.

PubMed

Hemati, Zeinab; Ashouri, Elaheh; AllahBakhshian, Maryam; Pourfarzad, Zahra; Shirani, Farimah; Safazadeh, Shima; Ziyaei, Marziyeh; Varzeshnejad, Maryam; Hashemi, Maryam; Taleghani, Fariba

2016-05-01

This article is a report of an analysis of the concept of dying with dignity. Dignity is an important component of providing care for dying patients and their families. Nevertheless, given that this concept is poorly defined, concept analysis is one of the best ways to define and clarify the concept of death with dignity with the aim to enhance its application in clinical practice, research and education. A search of multiple nursing and social sciences databases was undertaken, including Academic Search Complete, Science Direct, ProQuest, Scopus, Medline, PubMed, EBSCO, Ovid, Noormage, Cinahl, Magiran, PsycINFO and SID. After an extensive review of the literature from 1998-2014, about 14 related articles were included in the study. Based on these articles, the applications, attributes and experimental results of and references to death with dignity were recorded. Based on this analysis, the most important attributes of this concept included respect for privacy, respect, spiritual peace and hope. The antecedents of this concept included consideration of moral values during caregiving, preservation of human dignity as a patient right and professional ethics, and belief in the dignity of self and others, consideration of culture in providing end-of-life care. The consequences of this concept included a sense of peace in the patient and their family, peaceful death and provision of patient privacy and comfort. The concept of patient dignity has been referred to in many contexts. However, considering the dignity of dying patients commensurate with their culture is the most important component of care provided by nurses to facilitate a peaceful death. Respecting the dignity of the patient results in the reduction of her/his suffering and prepares her/him for a comfortable death. © 2016 John Wiley & Sons Ltd.

Saving Material with Systematic Process Designs

NASA Astrophysics Data System (ADS)

Kerausch, M.

2011-08-01

Global competition is forcing the stamping industry to further increase quality, to shorten time-to-market and to reduce total cost. Continuous balancing between these classical time-cost-quality targets throughout the product development cycle is required to ensure future economical success. In today's industrial practice, die layout standards are typically assumed to implicitly ensure the balancing of company specific time-cost-quality targets. Although die layout standards are a very successful approach, there are two methodical disadvantages. First, the capabilities for tool design have to be continuously adapted to technological innovations; e.g. to take advantage of the full forming capability of new materials. Secondly, the great variety of die design aspects have to be reduced to a generic rule or guideline; e.g. binder shape, draw-in conditions or the use of drawbeads. Therefore, it is important to not overlook cost or quality opportunities when applying die design standards. This paper describes a systematic workflow with focus on minimizing material consumption. The starting point of the investigation is a full process plan for a typical structural part. All requirements are definedaccording to a predefined set of die design standards with industrial relevance are fulfilled. In a first step binder and addendum geometry is systematically checked for material saving potentials. In a second step, blank shape and draw-in are adjusted to meet thinning, wrinkling and springback targets for a minimum blank solution. Finally the identified die layout is validated with respect to production robustness versus splits, wrinkles and springback. For all three steps the applied methodology is based on finite element simulation combined with a stochastical variation of input variables. With the proposed workflow a well-balanced (time-cost-quality) production process assuring minimal material consumption can be achieved.

Finite Element Analysis of ECAP, TCAP, RUE and CGP Processes

NASA Astrophysics Data System (ADS)

Patil, Deepak C.; Kallannavar, Vinayak; Bhovi, Prabhakar M.; Kori, S. A.; Venkateswarlu, K.

2016-02-01

A finite element method was applied to study the various severe plastic deformation processes like, Equal Channel Angular Pressing (ECAP), Tubular Channel Angular Pressing (TCAP), Repetitive Upsetting and Extrusion (RUE) and Constrained Groove Pressing (CGP), considering aluminum AA-390 alloy as specimen material for all these processes. FEA simulation was carried out using AFDEX simulation tool. Effect of the various ECAP process parameters like, die corner angle, channel angle, and the coefficient of friction were analyzed. The die corner angles were divided into 2 equal parts for increasing the effectiveness of ECAP process, thereby increasing the channel number from 2 to 3 and further, their influence on ECAP process was investigated. A 3D simulation of TCAP was carried out for die shapes like triangular and trapezoidal, and variation of the generated stress and strain was plotted. In CGP, four cycle operation was carried out; wherein each cycle is composed of corrugating the specimen and subsequent straightening to original dimension. During RUE process, a maximum effective stress of 683.1 MPa was induced in the specimen after processing it for four complete cycles of RUE process; whereas the maximum strain induced during the same condition was 3.715.

Die-target for dynamic powder consolidation

DOEpatents

Flinn, J.E.; Korth, G.E.

1985-06-27

A die/target is disclosed for consolidation of a powder, especially an atomized rapidly solidified metal powder, to produce monoliths by the dynamic action of a shock wave, especially a shock wave produced by the detonation of an explosive charge. The die/target comprises a rectangular metal block having a square primary surface with four rectangular mold cavities formed therein to receive the powder. The cavities are located away from the geometrical center of the primary surface and are distributed around such center while also being located away from the geometrical diagonals of the primary surface to reduce the action of reflected waves so as to avoid tensile cracking of the monoliths. The primary surface is covered by a powder retention plate which is engaged by a flyer plate to transmit the shock wave to the primary surface and the powder. Spawl plates are adhesively mounted on other surfaces of the block to act as momentum traps so as to reduce reflected waves in the block. 4 figs.

Die another way – non-apoptotic mechanisms of cell death

PubMed Central

Tait, Stephen W. G.; Ichim, Gabriel; Green, Douglas R.

2014-01-01

ABSTRACT Regulated, programmed cell death is crucial for all multicellular organisms. Cell death is essential in many processes, including tissue sculpting during embryogenesis, development of the immune system and destruction of damaged cells. The best-studied form of programmed cell death is apoptosis, a process that requires activation of caspase proteases. Recently it has been appreciated that various non-apoptotic forms of cell death also exist, such as necroptosis and pyroptosis. These non-apoptotic cell death modalities can be either triggered independently of apoptosis or are engaged should apoptosis fail to execute. In this Commentary, we discuss several regulated non-apoptotic forms of cell death including necroptosis, autophagic cell death, pyroptosis and caspase-independent cell death. We outline what we know about their mechanism, potential roles in vivo and define outstanding questions. Finally, we review data arguing that the means by which a cell dies actually matters, focusing our discussion on inflammatory aspects of cell death. PMID:24833670

s-Process in low metallicity Pb stars.

NASA Astrophysics Data System (ADS)

Bisterzo, S.; Gallino, R.; Straniero, O.; Ivans, I. I.; Käppeler, F.; Aoki, W.

We consider a sample of very metal-poor, C-rich, s-rich and lead-rich stars observed at high-resolution spectroscopy, and some recent spectroscopic data of C+s-rich stars obtained at moderate resolution. The spectroscopic data of these stars are interpreted with AGB theoretical models of different 13C-pocket efficiencies, initial mass and initial r-enrichment. When lead is not measured we give our theoretical prediction. The observed stars are not on the AGB phase, but are main sequence or giant stars. They acquired the C and s enrichments by mass transfer in a close binary system from the more massive companion while on the AGB (now a white dwarf). A considerable fraction of the stars show both high s and r enrichments. To explain the s+r enriched stars we assume a parental cloud already enriched in r-elements. The measurement of Nb is an indicator of an extrinsic AGB in a binary system. The intrinsic indicator [hs/ls] constrains the initial mass, while [Pb/hs] and [Pb/ls] are a measure of the s-process efficiency. The apparent discrepancies of C and N abundances may be reconciled by assuming a strong cool bottom process occurring during the AGB. An important primary production of light elements, from Ne to Si, increasing with the star mass, is predicted for AGB models at very low metallicity, induced by n capture on primary 22Ne and its progenies.

Increasing of the lifetime of large forging dies by repairwelding

NASA Astrophysics Data System (ADS)

Duchek, M.; Koukolikova, M.; Kotous, J.; Majer, M.

2018-02-01

Repair welding is often used for rebuilding discarded or failed forging dies. It saves the cost of new tools. Increased useful life of repaired dies is another motivation for repair welding. This article focuses on the development of new filler materials for this purpose. The main goal was to prolong the life of tools of DIN 1.2714 material. Filler wires of two chemistries were made and several samples were experimentally welded. Metallographic and tribological analyses were carried out.

Ways to Improve the Quality of Die Steel 5KhNM

NASA Astrophysics Data System (ADS)

Efimov, S. V.; Malykhina, O. Yu; Pavlova, A. G.; Milyuts, V. G.; Tsukanov, V. V.; Vikharev, V. V.

2017-12-01

There was performed an analysis of influence of the deoxidation technology, hydrogen content and high concentration of titanium in steel 5KhNM (Rus. “5XHM”) on quality of die blanks, evaluated based on the results of the ultrasonic test. The fractographic examinations of fractures and the X-ray microprobe analysis of chemical composition of non-metallic inclusions were conducted, the evaluation of macro- and micro-structure of a die blank with high titanium content was performed. It is demonstrated that defects of dies from steel 5KhNM (Rus. “5XHM”) are cracks from merged flakes and micro-flakes; in most cases large concentrations of sulphides appeared to be hydrogen collectors for formation of flakes and micro-flakes.

Communicating With Dying Patients and Their Families: Multimedia Training in End-of-Life Care.

PubMed

Chappell, Phylliss M; Healy, Jennifer; Lee, Shuko; Medellin, Glen; Sanchez-Reilly, Sandra

2017-08-01

The need for end-of-life (EOL), high-impact education initiatives to prepare medical students to communicate with dying patients and their families and to cope with issues of death and dying, is well recognized. Third-year medical students (n = 224), during their ambulatory rotation, completed a multimedia EOL curriculum, which included pre-/posttests, an online case-based module, didactic presentation, and a tablet computer application designed to demonstrate the signs and symptoms seen in the last hours of life for families of dying patients. Pre- and posttests were compared using Pearson χ 2 or Fisher exact test, and improvement was measured by weighted κ coefficient. On preintervention surveys, the majority of students demonstrated positive attitudes toward the care of dying patients and their families. Despite this high pretest positive attitude, there was a statistically significant overall positive attitude change after the intervention. The lowest pretest positive attitudes and lowest posttest positive attitude shifts, although all statistically improved, involved addressing the thoughts and feelings of dying patients and in coping with their own emotional response. Medical students exposure to this multimedia EOL curriculum increases positive attitudes in caring for dying patients and their families.

Dying neurons in thalamus of asphyxiated term newborns and rats are autophagic.

PubMed

Ginet, Vanessa; Pittet, Marie P; Rummel, Coralie; Osterheld, Maria Chiara; Meuli, Reto; Clarke, Peter G H; Puyal, Julien; Truttmann, Anita C

2014-11-01

Neonatal hypoxic-ischemic encephalopathy (HIE) still carries a high burden by its mortality and long-term neurological morbidity in survivors. Apart from hypothermia, there is no acknowledged therapy for HIE, reflecting the lack of mechanistic understanding of its pathophysiology. (Macro)autophagy, a physiological intracellular process of lysosomal degradation, has been proposed to be excessively activated in excitotoxic conditions such as HIE. The present study examines whether neuronal autophagy in the thalamus of asphyxiated human newborns or P7 rats is enhanced and related to neuronal death processes. Neuronal autophagy and cell death were evaluated in the thalamus (frequently injured in severe HIE) of both human newborns who died after severe HIE (n = 5) and P7 hypoxic-ischemic rats (Rice-Vannuci model). Autophagic (LC3, p62), lysosomal (LAMP1, cathepsins), and cell death (TUNEL, caspase-3) markers were studied by immunohistochemistry in human and rat brain sections, and by additional methods in rats (immunoblotting, histochemistry, and electron microscopy). Following severe perinatal asphyxia in both humans and rats, thalamic neurons displayed up to 10-fold (p < 0.001) higher numbers of autophagosomes and lysosomes, implying an enhanced autophagic flux. The highly autophagic neurons presented strong features of apoptosis. These findings were confirmed and elucidated in more detail in rats. These results show for the first time that autophagy is enhanced in severe HIE in dying thalamic neurons of human newborns, as in rats. Experimental neuroprotective strategies targeting autophagy could thus be a promising lead to follow for the development of future therapeutic approaches. © 2014 American Neurological Association.

Precision technique for trimming dies using a magnification device.

PubMed

Beck, D B

1980-05-01

This article described a technique for trimming a die under magnification. However, the microscope is also useful for checking (1) margins of wax patterns for completeness, (2) the internal surfaces of castings for imperfections, bubbles, or retained investment particles which could prevent proper seating of the castings on the dies, (3) for cracks or contamination in dental porcelain as well as porcelain flash on margins; and (4) precision attachment operation after casting or soldering procedures. Attention to detail in these laboratory procedures greatly improves the final fit of dental castings and saves subsequent chairside adjustments and remakes.

Asymmetric Die Grows Purer Silicon Ribbon

NASA Technical Reports Server (NTRS)

Kalejs, J. P.; Chalmers, B.; Surek, T.

1983-01-01

Concentration of carbide impurities in silicon ribbon is reduced by growing crystalline ribbon with die one wall higher than other. Height difference controls shape of meniscus at liquid/crystal interface and concentrates silicon carbide impurity near one of broad faces. Opposite face is left with above-average purity. Significantly improves efficiency of solar cells made from ribbon.

The Hospice: Advocate for the Dying.

ERIC Educational Resources Information Center

Anspaugh, David J.

1978-01-01

The hospice philosophy seeks to meet the needs of dying patients and their families. These needs include: effective control of pain; to be loved and to alleviate loneliness; to retain dignity and maintain control of as many aspects of life as possible; and to help the family be supportive and adapt to their inevitable loss. (JMF)

Mexican Educational Ethnography and the Work of the DIE: Crossing the Border and Finding the Historical Everyday [book review].

ERIC Educational Resources Information Center

Levinson, Bradley A.

1998-01-01

The theoretical insight and ethnographic rigor of this collection of essays from participants at Departamento de Investigaciones Educativas (DIE) of the National Polytechnic Institute about the role of the public school in Mexican social and political life promote understanding of educational processes in different contexts, including rural and…

Improving the automated optimization of profile extrusion dies by applying appropriate optimization areas and strategies

NASA Astrophysics Data System (ADS)

Hopmann, Ch.; Windeck, C.; Kurth, K.; Behr, M.; Siegbert, R.; Elgeti, S.

2014-05-01

The rheological design of profile extrusion dies is one of the most challenging tasks in die design. As no analytical solution is available, the quality and the development time for a new design highly depend on the empirical knowledge of the die manufacturer. Usually, prior to start production several time-consuming, iterative running-in trials need to be performed to check the profile accuracy and the die geometry is reworked. An alternative are numerical flow simulations. These simulations enable to calculate the melt flow through a die so that the quality of the flow distribution can be analyzed. The objective of a current research project is to improve the automated optimization of profile extrusion dies. Special emphasis is put on choosing a convenient starting geometry and parameterization, which enable for possible deformations. In this work, three commonly used design features are examined with regard to their influence on the optimization results. Based on the results, a strategy is derived to select the most relevant areas of the flow channels for the optimization. For these characteristic areas recommendations are given concerning an efficient parameterization setup that still enables adequate deformations of the flow channel geometry. Exemplarily, this approach is applied to a L-shaped profile with different wall thicknesses. The die is optimized automatically and simulation results are qualitatively compared with experimental results. Furthermore, the strategy is applied to a complex extrusion die of a floor skirting profile to prove the universal adaptability.

Natural law and the "right to die".

PubMed

Whiting, R A

Over the last two decades social concerns with the "right to die" have grown beyond the ability of our governmental and judicial institutions to consistently deal with them. One reason for this difficulty has been the unavailability of any legal or judicial standard that is consistent with American conceptions of liberty, morality, and justice. This article attempts to examine the theory of natural law to determine whether it may provide a consistent standard for resolving these difficult questions. As natural law theories are traced through history, they lead directly to the United States where a uniquely American interpretation became one of the foundational principles for our constitution. By applying these theories to the contemporary question of the "right to die," natural law can again provide the foundational principles needed to develop standards for dealing with such questions that are consistent with our historical, philosophical, and political traditions.

GPU-basierte Smart Visibility Techniken für die Planung von Tumor-Operationen

NASA Astrophysics Data System (ADS)

Tietjen, Christian; Kubisch, Christoph; Hiller, Stefan; Preim, Bernhard

Bei der Planung von Tumoroperationen ist die Einschätzung von Abständen und Infiltrationen zu vitalen Strukturen wichtig. Im Bereich der medizinischen Visualisierung wurden hierfür bereits zahlreiche Techniken entwickelt, die unter dem Begriff Smart Visibility zusammengefasst werden. Zu diesen zählen Ghost Views und Section Views. In diesem Beitrag wird eine GPU-basierte Realisierung dieser Techniken für polygonale Daten vorgestellt. Die Parametrisierung der Techniken erfolgt automatisch, um einen klinischen Einsatz ermöglichen zu können.

Multi-compartmental modeling of SORLA’s influence on amyloidogenic processing in Alzheimer’s disease

PubMed Central

2012-01-01

Background Proteolytic breakdown of the amyloid precursor protein (APP) by secretases is a complex cellular process that results in formation of neurotoxic Aβ peptides, causative of neurodegeneration in Alzheimer’s disease (AD). Processing involves monomeric and dimeric forms of APP that traffic through distinct cellular compartments where the various secretases reside. Amyloidogenic processing is also influenced by modifiers such as sorting receptor-related protein (SORLA), an inhibitor of APP breakdown and major AD risk factor. Results In this study, we developed a multi-compartment model to simulate the complexity of APP processing in neurons and to accurately describe the effects of SORLA on these processes. Based on dose–response data, our study concludes that SORLA specifically impairs processing of APP dimers, the preferred secretase substrate. In addition, SORLA alters the dynamic behavior of β-secretase, the enzyme responsible for the initial step in the amyloidogenic processing cascade. Conclusions Our multi-compartment model represents a major conceptual advance over single-compartment models previously used to simulate APP processing; and it identified APP dimers and β-secretase as the two distinct targets of the inhibitory action of SORLA in Alzheimer’s disease. PMID:22727043

Magnetisches Tracking für die Navigation mit dem da Vinci® Surgical System

NASA Astrophysics Data System (ADS)

Nickel, Felix; Wegner, Ingmar; Kenngott, Hannes; Neuhaus, Jochen; Müller-Stich, Beat P.; Meinzer, Hans-Peter; Gutt, Carsten N.

In dieser Studie wurde untersucht ob in einem typischen OP-Aufbau mit dem da Vinci® Telemanipulator elektromagnetisches Tracking für die Realisation eines Navigationssystems eingesetzt werden kann. Hierfür wurde in einem realen OP-Aufbau untersucht, wie stark metallische und ferromagnetisch wirksame Objekte wie Operationstisch und Telemanipulator das elektromagnetische Feld des Trackingsystems beeinflussen. Die Ergebnisse zeigen, dass der Telemanipulator nur unwesentlich die Störung des Magnetfeldes durch den OP-Tisch verstärkt. Insbesondere die Bewegung der Instrumente im Trackingvolumen verursachte keine zusätzliche relevante Störung des Magnetfeldes. Bei Begrenzung des Trackingvolumens auf eine Länge von 190 mm, Höhe von 200mm und Breite von 400 mm war der maximale Fehler in diesem Bereich an allen Messpunkten kleiner 10 mm. Der Einsatz von elektromagnetischem Tracking für die Navigation mit dem da Vinci® Surgical System ist somit in einem begrenzten Arbeitsvolumen mit hinreichender Genauigkeit möglich.

Hospice nurses’ emotional challenges in their encounters with the dying

PubMed Central

Ingebretsen, Lina Paola; Sagbakken, Mette

2016-01-01

The purpose of this study was to explore nurses’ emotional challenges when caring for the dying in hospices. The study has a qualitative design, and knowledge was developed through a dialectical exchange between theory and data. Ten individual in-depth interviews were conducted with nurses recruited from two hospices in Denmark. Although all of the nurses said that they experienced emotional challenges or felt emotionally touched during their work, the study found a variety of opinions related to the extent to which their emotional reactions should be revealed in their role as a hospice professional. The participants described their emotional challenges as being simultaneously draining and enriching experiences leading to personal and professional growth and development. The study may contribute to increased awareness of emotional challenges for hospice nurses, which involve continuous reflection and balancing between meeting the dying as a human being and meeting the dying as a hospice professional. PMID:27258584

A Dying Star in a Different Light