Prepare to protect: Operating and maintaining a tornado safe room.

PubMed

Herseth, Andrew; Goldsmith-Grinspoon, Jennifer; Scott, Pataya

2017-06-01

Operating and maintaining a tornado safe room can be critical to the effective continuity of business operations because a firm's most valuable asset is its people. This paper describes aspects of operations and maintenance (O&M) for existing tornado safe rooms as well as a few planning and design aspects that affect the ultimate operation of a safe room for situations where a safe room is planned, but not yet constructed. The information is based on several Federal Emergency Management Agency safe room publications that provide guidance on emergency management and operations, as well as the design and construction of tornado safe rooms.

Double-Glazing Interferometry

ERIC Educational Resources Information Center

Toal, Vincent; Mihaylova, Emilia M.

2009-01-01

This note describes how white light interference fringes can be seen by observing the Moon through a double-glazed window. White light interferometric fringes are normally observed only in a well-aligned interferometer whose optical path difference is less than the coherence length of the light source, which is approximately one micrometer for…

Influence of Laser Glazing on the Characterization of Plasma-Sprayed YSZ Coatings

NASA Astrophysics Data System (ADS)

Wang, Yan; Liu, Jiangwei; Liao, Hanlin; Darut, Geoffrey; Stella, Jorge; Poirier, Thierry; Planche, Marie-Pierre

2017-01-01

In this study, 8 wt.% yttria-stabilized zirconia powder was deposited on the substrates by atmospheric plasma spray. The coatings were post-treated by laser glazing under different parameters in order to densify them. The characterization of the laser molten pools under different laser treatment conditions was studied. Preheating processes were also employed. Scanning electron microscopy observations of the surface and cross section of as-sprayed and laser-glazed coatings were carried out to investigate the influence of laser glazing on the microstructure on laser-glazed coatings. The results show that preheating processes improve the coating in terms of deepening the laser-glazed layer, reducing the number of vertical cracks and surface density of cracks and widening the molten pool. Finally, the influences of linear energy density on the characterization of the glazed layer are discussed.

24 CFR 3280.113 - Glass and glazed openings.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 24 Housing and Urban Development 5 2011-04-01 2011-04-01 false Glass and glazed openings. 3280.113... Glass and glazed openings. (a) Windows and sliding glass doors. All windows and sliding glass doors shall meet the requirements of § 3280.403 the “Standard for Windows and Sliding Glass Doors Used in...

The risks associated with falling parts of glazed facades in case of fire

NASA Astrophysics Data System (ADS)

Sędłak, Bartłomiej; Kinowski, Jacek; Sulik, Paweł; Kimbar, Grzegorz

2018-05-01

Arguably, one of the most important requirement a building have to meet in case of fire is to ensure the safe evacuation of its users and the work of rescue teams. Consequently, issues related to the risks associated with falling parts of facades are fairly well known around Europe. Even though not equally well defined as other fire safety requirements concerning glazed facades, there is plenty of test methods for assessment of facades regarding falling parts, mostly based on an approach related to fire spread. In this paper selection of test method for assessment of facades regarding falling parts is briefly presented. However, focus of this work is on fire test of typical glazed segment of façade performed in ITB Laboratory. Results of the test positively verifies conjecture that solutions with glass units configured with thin, tempered glass panes on the outer side should pose no threat. However, the question has been raised whether the behaviour of other glass unit solutions (with additional coatings or laminated) would be similar.

Effect of Iron Oxide and Phase Separation on the Color of Blue Jun Ware Glaze.

PubMed

Wang, Fen; Yang, Changan; Zhu, Jianfeng; Lin, Ying

2015-09-01

Based on the traditional Jun ware glaze, the imitated Jun ware glazes were prepared by adding iron oxide and introducing phase separation agent apatite through four-angle-method. The effect of iron oxide contents, phase separation and the firing temperature on the color of Jun ware glazes were investigated by a neutral atmosphere experiment, optical microscope and scanning electronic microscope. The results showed that the colorant, mainly Fe2O3, contributed to the Jun ware glaze blue and cyan colors of Jun ware glaze. The light scatter caused by the small droplets in phase separation structure only influenced the shade of the glaze color, intensify or weaken the color, and thus made the glaze perfect and elegant opal visual effects, but was not the origin of general blue or cyan colors of Jun ware glaze. In addition, the firing temperature and the basic glaze composition affected the glaze colors to some extent.

Chemical durability of glaze on Zsolnay architectural ceramics (Budapest, Hungary) in acid solutions

NASA Astrophysics Data System (ADS)

Baricza, Ágnes; Bajnóczi, Bernadett; May, Zoltán; Tóth, Mária; Szabó, Csaba

2015-04-01

Zsolnay glazed architectural ceramics are among the most famous Hungarian ceramics, however, there is no profound knowledge about the deterioration of these building materials. The present study aims to reveal the influence of acidic solutions in the deterioration of Zsolnay ceramics. The studied ceramics are glazed roof tiles, which originate from two buildings in Budapest: one is located in the densely built-up city centre with high traffic rate and another one is in a city quarter with moderate traffic and more open space. The roof tiles represent the construction and the renovation periods of the buildings. The ceramics were mainly covered by lead glazes in the construction period and mainly alkali glazes in the renovation periods. The glaze of the tiles were coloured with iron (for yellow glaze) or chromium/copper/iron (for green glazes) in the case of the building located in the city centre, whereas cobalt was used as colorant and tin oxide as opacifier for the blue glaze of the ceramics of the other building. Six tiles were selected from each building. Sulphuric acid (H2SO4) solutions of pH2 and pH4 were used to measure the durability of the glazes up to 14 days at room temperature. The surfaces of the glazed ceramics after the treatment were measured by X-ray diffraction, Raman spectroscopy and SEM-EDS techniques to determine the precipitated phases on the surface of the glaze. Electron microprobe analysis was used to quantitatively characterise phases found and to determine the chemical composition of the treated glaze. The recovered sulphuric acid solutions were measured with ICP-OES technique in order to quantify the extent of the ion exchange between the glaze and the solutions. There is a significant difference in the dissolution rates in the treatments with sulphuric acid solutions of pH2 and pH4, respectively. The solution of pH2 induced greater ion exchange (approx. 7-10 times) from the glaze compared to the solution of pH4. Alkali and alkali earth

Characterization of Low Firing Temperature Ceramic Glaze Using Phuket MSW and Soda Lime Cullet

NASA Astrophysics Data System (ADS)

Ketboonruang, P.; Jinawat, S.; Kashima, D. P.; Wasanapiarnpong, T.; Sujaridworakun, P.; Buggakuptav, W.; Traipol, N.; Jiemsirilers, S.

2011-10-01

The normal firing temperature of ceramic products is around 1200 °C. In order to reduce firing temperature, industrial wastes were utilized in ceramic glaze. Phuket municipal solid waste (MSW), soda lime cullet, and borax were used as raw materials for low firing temperature glazes. The glaze compositions were designed using a triaxial diagram. Stoneware ceramic body was glazed then fired at 1000 and 1150 °C for 15 minutes. Morphology and phase composition of glazes were analyzed by Scanning electron microscopy (SEM-EDS) and X-ray diffraction (XRD). Thermal expansion compatibility of Stoneware body and glazes were investigated using a dilatometer. Melting behaviour of selected glaze was analyzed by heating stage microscopy. Phuket MSW and Soda lime glass cullet can be used in high percentage as major raw materials for low firing temperature ceramic glaze that show good texture and vitrified at lower firing temperature without using any commercial ceramic frits. The firing temperature can be reduced up to 150 °C in this study.

Chemical resistance and cleanability of glazed surfaces

NASA Astrophysics Data System (ADS)

Hupa, Leena; Bergman, Roger; Fröberg, Linda; Vane-Tempest, Stina; Hupa, Mikko; Kronberg, Thomas; Pesonen-Leinonen, Eija; Sjöberg, Anna-Maija

2005-06-01

Adhesion of soil on glazed surfaces and their cleanability depends on chemical composition, phase composition, and roughness of the surface. The surface can be glossy consisting mainly of a smooth glassy phase. A matt and rough surface consists of a glassy phase and one or more crystalline phases. The origin and composition of the crystalline phases affect the chemical resistance and the cleanability of the surface. Fifteen experimental glossy and matt glazes were soaked in a slightly alkaline cleaning agent solution. The surfaces were spin-coated with sebum, i.e. a soil component typical for sanitary facilities. After wiping out the soil film in a controlled manner, the surface conditions and the soil left were evaluated with colour measurements, SEM/EDXA and COM. The results show that wollastonite-type crystals in the glaze surfaces were attacked in aqueous solutions containing typical cleaning agents. This corrosion led to significant decrease in the cleanability of the surface. The other crystal types observed, i.e. diopside and quartz crystals were not corroded, and the cleanability of glazes containing only these crystals was not changed in the cleaning agent exposures. Also the glassy phase was found to be attacked in some formulations leading to a somewhat decreased cleanability. The repeated soiling and cleaning procedures indicated that soil is accumulated on rough surfaces and surfaces which were clearly corroded by the cleaning agent.

Chromogenic switchable glazing: Towards the development of the smart window

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lampert, C.M.

1995-06-01

The science and technology of chromogenic materials for switchable glazings in building applications is discussed. These glazings can be used for dynamic control of solar and visible energy. Currently many researchers and engineers are involved with the development of products in this field. A summary of activities in Japan, Europe, Australia, USA and Canada is made. The activities of the International Energy Agency are included. Both non-electrically activated and electrically activated glazings are discussed. Technologies covered in the first category are photochromics, and thermochromics and thermotropics. A discussion of electrically activated chromogenic glazings includes dispersed liquid crystals, dispersed particles andmore » electrochromics. A selection of device structures and performance characteristics are compared. A discussion of transparent conductors is presented. Technical issues concerning large-area development of smart windows are discussed.« less

44. GLAZE STORAGE AND MIXING AREA, GROUND FLOOR, EAST WING. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

44. GLAZE STORAGE AND MIXING AREA, GROUND FLOOR, EAST WING. TILES ARE DIPPED IN GLAZE AT THE COUNTER AGAINST THE FAR WALL. - Moravian Pottery & Tile Works, Southwest side of State Route 313 (Swamp Road), Northwest of East Court Street, Doylestown, Bucks County, PA

49 CFR 571.205 - Standard No. 205, Glazing materials.

Code of Federal Regulations, 2014 CFR

2014-10-01

... providing shelter for persons. Glass-plastic glazing material means a laminate of one or more layers of glass and one or more layers of plastic in which a plastic surface of the glazing faces inward when the... vehicle or camper; or (b) To be cut into components for use in motor vehicles or items of motor vehicle...

49 CFR 571.205 - Standard No. 205, Glazing materials.

Code of Federal Regulations, 2013 CFR

2013-10-01

... providing shelter for persons. Glass-plastic glazing material means a laminate of one or more layers of glass and one or more layers of plastic in which a plastic surface of the glazing faces inward when the... vehicle or camper; or (b) To be cut into components for use in motor vehicles or items of motor vehicle...

49 CFR 571.205 - Standard No. 205, Glazing materials.

Code of Federal Regulations, 2012 CFR

2012-10-01

... providing shelter for persons. Glass-plastic glazing material means a laminate of one or more layers of glass and one or more layers of plastic in which a plastic surface of the glazing faces inward when the... vehicle or camper; or (b) To be cut into components for use in motor vehicles or items of motor vehicle...

49 CFR 571.205 - Standard No. 205, Glazing materials.

Code of Federal Regulations, 2011 CFR

2011-10-01

... providing shelter for persons. Glass-plastic glazing material means a laminate of one or more layers of glass and one or more layers of plastic in which a plastic surface of the glazing faces inward when the... component of any specific motor vehicle or camper; or (b) To be cut into components for use in motor...

Investigation of surface water behavior during glaze ice accretion

NASA Technical Reports Server (NTRS)

Hansman, R. John, Jr.; Turnock, Stephen R.

1990-01-01

A series of experimental investigations that focused on isolating the primary factors that control the behavior of unfrozen surface water during glaze ice accretion were conducted. Detailed microvideo observations were made of glaze ice accretions on 2.54 cm diam cylinders in a closed-loop refrigerated wind tunnel. Distinct zones of surface water behavior were observed; a smooth wet zone in the stagnation region with a uniform water film, a rough zone where surface tension effects caused coalescence of surface water into stationary beads, and a zone where surface water ran back as rivulets. The location of the transition from the smooth to the rough zone was found to migrate towards the stagnation point with time. Comparative tests were conducted to study the effect of the substrate thermal and roughness properties on ice accretion. The importance of surface water behavior was evaluated by the addition of a surface tension reducing agent to the icing tunnel water supply, which significantly altered the accreted glaze ice shape. Measurements were made to determine the contact angle behavior of water droplets on ice. A simple multizone modification to current glaze ice accretion models was proposed to include the observed surface roughness behavior.

Cleanability evaluation of ceramic glazes with nanometer far-infrared materials using contact angle measurement.

PubMed

Wang, Lijuan; Liang, Jinsheng; Di, Xingfu; Tang, Qingguo

2014-05-01

The cleanability of easy-to-clean ceramic glazes doped with nanometer far-infrared materials was compared with that of some high-quality household ceramic glazes from the market. The cleanability was evaluated by the contact angle measurement using a sessile drop method with a Dataphysics OCA-30 contact angle analyzer. The results showed that the difference of contact angles of water on the glazes before soiling and after cleaning could be used as a parameter for evaluating the cleanability of the glazes. The relationship between cleanability and surface properties, such as surface free energy and surface topography, was investigated. The surface free energy of the samples and their components were calculated using van Oss acid-base approach. By measuring advancing and receding contact angles, the contact angle hysteresis of the ceramic glazes due to the surface topography was investigated. It was shown that the cleanability of ceramic glazes containing nanometer far-infrared materials (NFIM) is better than that of household ceramic glazes from market, due to a higher ratio of electron-acceptor parameter to electron-donor parameter, which led to the effect of water hydration as well as better hydrophilic property and increased smoothness. The contact angle measurement not only accurately evaluates the cleanability of the ceramic glazes, but also has a contribution to the study of cleanability theory. Moreover, this method is simple, convenient and less sample-consumption.

Characterization of the glaze and in-glaze pigments of the nineteenth-century relief tiles from the Pena National Palace, Sintra, Portugal

NASA Astrophysics Data System (ADS)

Coutinho, M. L.; Veiga, J. P.; Alves, L. C.; Mirão, J.; Dias, L.; Lima, A. M.; Muralha, V. S.; Macedo, M. F.

2016-07-01

The glaze and in-glaze pigments of the historical nineteenth-century glazed tiles from the Pena National Palace (Sintra, Portugal) were characterized using a multi-analytical approach. Chemical composition and microstructural characterization were ascertained by µ-PIXE, µ-Raman, optical microscopy and VP-SEM-EDS. The manufacturing technique and colour palette in these tiles were found to be close to the ceramic pigments used in traditional majolica. The blue and purple colours derive from cobalt oxide and manganese oxide, respectively. A mixture of Pb-Sn-Sb yellow with cobalt oxide and iron oxide was used for green and dark yellow, respectively, while grey tonalities consist of a complex mixture of cobalt oxide, manganese oxide and Pb-Sn-Sb yellow in different proportions. Results obtained allowed the determination of the oxides and elements used in pigments as well as production techniques, resorting to traditional majolica manufacture, although the tiles were produced by the end of the nineteenth century.

49 CFR 238.421 - Glazing.

Code of Federal Regulations, 2010 CFR

2010-10-01

... window on a passenger car and a power car cab shall comply with the requirements contained in part 223 of this chapter. (b) Particular end-facing exterior glazing requirements. Each end-facing exterior window... penetration or spall. An impact angle that is perpendicular (90 degrees) to the window's surface shall be...

Safely Enabling UAS Operations in Low-Altitude Airspace

NASA Technical Reports Server (NTRS)

Kopardekar, Parimal H.

2016-01-01

Flexibility where possible, and structure where necessary. Consider the needs of national security, safe airspace operations, economic opportunities, and emerging technologies. Risk-based approach based on population density, assets on the ground, density of operations, etc. Digital, virtual, dynamic, and as needed UTM services to manage operations.

Safely Enabling UAS Operations in Low-Altitude Airspace

NASA Technical Reports Server (NTRS)

Kopardekar, Parimal

2017-01-01

NASA is developing a system to safely enable low altitude unmanned aerial system (UAS) operations. The system is referred to as UAS Traffic Management (UTM). The UTM will safely enable a variety of business models and multiple operations in the same airspace. The UTM will provide services such as airspace configuration and geo-fencing, weather and wind integration, demand-capacity imbalance management, and separation management, and contingency management. The UTM research and development has been conducted in collaboration with many in industry, academia, and government. The UTM system will evolve through four builds. Each build will be collaboratively tested with partners. The final prototype will be available for persistent daily use of UAS operations beyond line of sight.

12 CFR 238.8 - Safe and sound operations.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 12 Banks and Banking 4 2013-01-01 2013-01-01 false Safe and sound operations. 238.8 Section 238.8... (CONTINUED) SAVINGS AND LOAN HOLDING COMPANIES (REGULATION LL) General Provisions § 238.8 Safe and sound... inconsistent with sound banking principles or the purposes of HOLA or the Financial Institutions Supervisory...

12 CFR 238.8 - Safe and sound operations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 12 Banks and Banking 4 2014-01-01 2014-01-01 false Safe and sound operations. 238.8 Section 238.8... (CONTINUED) SAVINGS AND LOAN HOLDING COMPANIES (REGULATION LL) General Provisions § 238.8 Safe and sound... inconsistent with sound banking principles or the purposes of HOLA or the Financial Institutions Supervisory...

12 CFR 238.8 - Safe and sound operations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 12 Banks and Banking 4 2012-01-01 2012-01-01 false Safe and sound operations. 238.8 Section 238.8... (CONTINUED) SAVINGS AND LOAN HOLDING COMPANIES (REGULATION LL) General Provisions § 238.8 Safe and sound... inconsistent with sound banking principles or the purposes of HOLA or the Financial Institutions Supervisory...

49 CFR 571.205(a) - Glazing equipment manufactured before September 1, 2006 and glazing materials used in vehicles...

Code of Federal Regulations, 2014 CFR

2014-10-01

... injuries resulting from impact to glazing surfaces, to ensure a necessary degree of transparency in motor... transverse plane that passes through the shoulder reference point (as described in Figure 1 of Section 571...

49 CFR 571.205(a) - Glazing equipment manufactured before September 1, 2006 and glazing materials used in vehicles...

Code of Federal Regulations, 2012 CFR

2012-10-01

... injuries resulting from impact to glazing surfaces, to ensure a necessary degree of transparency in motor... transverse plane that passes through the shoulder reference point (as described in Figure 1 of Section 571...

49 CFR 571.205(a) - Glazing equipment manufactured before September 1, 2006 and glazing materials used in vehicles...

Code of Federal Regulations, 2011 CFR

2011-10-01

... injuries resulting from impact to glazing surfaces, to ensure a necessary degree of transparency in motor... through the shoulder reference point (as described in Figure 1 of Section 571.210 Seat belt assembly...

49 CFR 571.205(a) - Glazing equipment manufactured before September 1, 2006 and glazing materials used in vehicles...

Code of Federal Regulations, 2013 CFR

2013-10-01

... injuries resulting from impact to glazing surfaces, to ensure a necessary degree of transparency in motor... transverse plane that passes through the shoulder reference point (as described in Figure 1 of Section 571...

Energy Efficient Glazing for Adaptive Solar Control Fabricated with Photothermotropic Hydrogels Containing Graphene Oxide

PubMed Central

Kim, Dowan; Lee, Eunsu; Lee, Heon Sang; Yoon, Jinhwan

2015-01-01

Glazing for adaptive solar control is the most promising for energy efficient development, because the use of this technology in buildings can be expected to significantly impact energy use and efficiency by screening sunlight that enters a building in summer. To achieve autonomous adjustable transparency, we have developed photothermotropic material system by combining photothermal materials with thermotropic hydrogels. We found that graphene oxide dispersed within a hydrogel matrix effectively converts the photo energy of sunlight into thermal energy, providing the efficient means to trigger transparency of thermotropic hydrogels. Therefore, we could develop switchable glazing of novel photothermotropic mechanism that screen strong sunlight and heat radiation in response to the sunlight intensity, as well as the temperature. Furthermore, in this study, a prototype device was manufactured with developed materials and successfully operated in outdoor testing. PMID:25561372

Embracing Safe Ground Test Facility Operations and Maintenance

NASA Technical Reports Server (NTRS)

Dunn, Steven C.; Green, Donald R.

2010-01-01

Conducting integrated operations and maintenance in wind tunnel ground test facilities requires a balance of meeting due dates, efficient operation, responsiveness to the test customer, data quality, effective maintenance (relating to readiness and reliability), and personnel and facility safety. Safety is non-negotiable, so the balance must be an "and" with other requirements and needs. Pressure to deliver services faster at increasing levels of quality in under-maintained facilities is typical. A challenge for management is to balance the "need for speed" with safety and quality. It s especially important to communicate this balance across the organization - workers, with a desire to perform, can be tempted to cut corners on defined processes to increase speed. Having a lean staff can extend the time required for pre-test preparations, so providing a safe work environment for facility personnel and providing good stewardship for expensive National capabilities can be put at risk by one well-intending person using at-risk behavior. This paper documents a specific, though typical, operational environment and cites management and worker safety initiatives and tools used to provide a safe work environment. Results are presented and clearly show that the work environment is a relatively safe one, though still not good enough to keep from preventing injury. So, the journey to a zero injury work environment - both in measured reality and in the minds of each employee - continues. The intent of this paper is to provide a benchmark for others with operational environments and stimulate additional sharing and discussion on having and keeping a safe work environment.

Floor tile glass-ceramic glaze for improvement of the resistance to surface abrasion

NASA Astrophysics Data System (ADS)

Gajek, M.; Lis, J.; Partyka, J.; Wójczyk, M.

2011-10-01

The results of research aimed at the study on frits and glass-ceramic glazes for floor tiles, based on compositions located in the primary field of cordierite crystallization within the system MgO-Al2O3-SiO2, have been presented. The results comprise investigations on the frits crystallization abilities, stability of the crystallizing phase under conditions of single-stage a fast firing cycle (time below 60 minutes) depending on their chemical composition and the influence of the nucleation agents. The influence of the nucleating agents namely TiO2, ZrO2, V2O5 on phase composition of obtained crystalline glazes, mechanical parameters and microstructure, has been examined. The strength tests proved increased mechanical resistance of crystalline glazes. Obtained glazes are characterized by high microhardness in range 6~8 GPa, as well as the increased wear resistance measured by the loss of weight below 100 mg / 55 cm2 (PN-EN ISO 10545-7). Significant increase of these parameters as compared with non-crystalline glazes, where micro-hardness values range between 5~6 GPa and the wear resistance values range from 120 to 200 mg, has been proved. Starting glasses (frits) and glazes of the ternary system MgO-SiO2-Al2O3, were examined with use of DTA, XRD and SEM methods.

Safely Enabling UAS Operations in Low-Altitude Airspace

NASA Technical Reports Server (NTRS)

Kopardekar, Parimal

2017-01-01

NASA is developing a system to safely enable low altitude unmanned aerial system (UAS) operations. The system is referred to as UAS Traffic Management (UTM). The UTM will safely enable a variety of business models and multiple operations in the same airspace. The UTM will provide services such as airspace configuration and geo-fencing, weather and wind integration, demand-capacity imbalance management, and separation management, and contingency management. The UTM research and development has been conducted in collaboration with many in industry, academia, and government. The UTM system will evolve through four builds. Each build will be collaboratively tested with partners. The final prototype will be available for persistent daily use of UAS operations beyond visual line of sight (BVLOS).

A safe operating space for humanity

Treesearch

Johan Rockström; Will Steffen; Kevin Noone; Asa Persson; F. Stuart Chapin; Eric F. Lambin; Timothy M. Lenton; Marten Scheffer; Carl Folke; Hans Joachim Schellnhuber; Björn Nykvist; Cynthia A. de Wit; Terry Hughes; Sander van der Leeuw; Henning Rodhe; Sverker Sörlin; Peter K. Snyder; Robert Costanza; Uno Svedin; Malin Falkenmark; Louise Karlberg; Robert W. Corell; Victoria J. Fabry; James Hansen; Brian Walker; Diana Liverman; Katherine Richardson; Paul Crutzen; Jonathan A. Foley

2009-01-01

To meet the challenge of maintaining the Holocene state, we propose a framework based on 'planetary boundaries'. These boundaries define the safe operating space for humanity with respect to the Earth system and are associated with the planet's biophysical subsystems or processes. Although Earth's complex systems sometimes respond smoothly to...

Modeling of surface roughness effects on glaze ice accretion

NASA Technical Reports Server (NTRS)

Hansman, R. John, Jr.; Yamaguchi, Keiko; Berkowitz, Brian M.; Potapczuk, Mark

1990-01-01

A series of experimental investigations focused on studying the cause and effect of roughness on accreting glaze ice surfaces were conducted. Detailed microvideo observations were made of glaze ice accretions on 1 to 4 inch diameter cylinders in three icing wind tunnels (the Data Products of New England six inch test facility, the NASA Lewis Icing Research Tunnel, and the B. F. Goodrich Ice Protection Research Facility). Infrared thermal video recordings were made of accreting ice surfaces in the Goodrich facility. Distinct zones of surface water behavior were observed; a smooth wet zone in the stagnation region with a uniform water film; a rough zone where surface tension effects caused coalescence of surface water into stationary beads; a horn zone where roughness elements grow into horn shapes; a runback zone where surface water ran back as rivulets; and a dry zone where rime feathers formed. The location of the transition from the smooth to the rough zone was found to migrate with time towards the stagnation point. The behavior of the transition appeared to be controlled by boundary layer transition and bead formation mechanisms at the interface between the smooth and rough zones. Regions of wet ice growth and enhanced heat transfer were clearly visible in the infrared video recordings of glaze ice surfaces. A simple multi-zone modification to the current glaze ice accretion model was proposed to include spatial variability in surface roughness.

Thermal Simulation of a Zero Energy Glazed Pavilion in Sofia, Bulgaria. New Strategies for Energy Management by Means of Water Flow Glazing

NASA Astrophysics Data System (ADS)

del Ama Gonzalo, Fernando; Hernandez Ramos, Juan A.; Moreno, Belen

2017-10-01

The building sector is primarily responsible for a major part of total energy consumption. The European Energy Performance of Buildings Directives (EPBD) emphasized the need to reduce the energy consumption in buildings, and put forward the rationale for developing Near to Zero Energy Buildings (NZEB). Passive and active strategies help architects to minimize the use of active HVAC systems, taking advantage of the available natural resources such as solar radiation, thermal variability and daylight. The building envelope plays a decisive role in passive and active design strategies. The ideal transparent façade would be one with optical properties, such as Solar Heat Gain Coefficient (SHGC) and Visible Transmittance (VT), that could readily adapt in response to changing climatic conditions or occupant preferences. The aim of this article consists of describing the system to maintain a small glazed pavilion located in Sofia (Bulgaria) at the desired interior temperature over a whole year. The system comprises i) the use of Water Flow Glazing facades (WFG) and Radiant Interior Walls (RIW), ii) the use of free cooling devices along with traditional heat pump connected to photo-voltaic panels and iii) the use of a new Energy Management System that collects data and acts accordingly by controlling all components. The effect of these strategies and the use of active systems, like Water Flow Glazing, are analysed by means of simulating the prototype over one year. Summer and Winter energy management strategies are discussed in order to change the SHGC value of the Water Flow Glazing and thus, reduce the required energy to maintain comfort conditions.

49 CFR 393.62 - Emergency exits for buses.

Code of Federal Regulations, 2010 CFR

2010-10-01

... NECESSARY FOR SAFE OPERATION Glazing and Window Construction § 393.62 Emergency exits for buses. (a) Buses... glazing if such glazing is not contained in a push-out window; or, at least 432 cm2 (67 square inches) of free opening resulting from opening of a push-out type window. No area shall be included in this...

[Adhesion of oral microorganisms on dental porcelain polished and glazed].

PubMed

Wang, Yi-ning; Wen, Guo-jiang; Shi, Bin; Pan, Xin-hua

2003-09-01

This study compared the roughness of porcelain polished or glazed surfaces and the adhesion of oral streptococcus mutans to them in vitro. 30 porcelain samples were made. Porcelain samples in group A were polished with diamond paste. Porcelain samples were glazed in group B and were polished with Al2O3 (240#) bur in group C. Their roughness values were measured by profilometer. Standardized cell suspensions were incubated with test samples for one hour at 37 degrees C, then retained cells were counted by image analysis (percentage area of a microscopic field covered by cells). Roughness values of group A, B, C were respectively (0.1987 +/- 0.057) microm, (0.1990 +/- 0.091) microm, (0.4260 +/- 0.174) microm. There was no significantly difference between group A and group B. The roughness samples in group C were significantly rougher than that in the other groups. The amount of retained cells in group A, group B, group C was respectively (15.92 +/- 4.37)%, (16.39 +/- 6.31)% and (41.48 +/- 12.1)%. There was no significant difference between the cell adhesion on porcelain surface glazed and polished, but more bacteria adhered on the porcelain surface in group C. Porcelain surface polished treatment was clinically acceptable compared with its glazed. They all exhibited the least amount of bacteria adhesion. The more porcelain surface was rough, the more bacteria adhered on it.

The effect of photo-activated glazes on the microhardness of acrylic baseplate resins.

PubMed

Emmanouil, J K; Kavouras, P; Kehagias, Th

2002-01-01

A comparative investigation of acrylic denture base surface microhardness, induced through glazing with different photo-activated liquids. Thermopolymerized acrylic resin Paladon 65 (Kulzer) was used for this study. The samples were mechanically thinned by silicon carbide grinding papers and finally, mechanically polished by alumina pastes. The samples were then glazed with Palaseal, Plaquit and Lightplast-Lack photo-activated liquids. Microhardness tests were carried out via a Zeiss optical microscope equipped with an Anton Paar microhardness tester fitted with a Knoop indenter. Microhardness testing performed on surfaces glazed by Plaquit, Lightplast-Lack, and Palaseal photo-activated liquids showed enhanced microhardness values compared to the mechanically polished acrylic resin denture base material. Comparative microhardness tests performed on acrylic base resin treated with photo-activated acrylic glazes showed that all increases the surface microhardness. The enhancement of surface microhardness of acrylic denture bases suggests that they are likely to resist wear during service.

Soft tissue adhesion of polished versus glazed lithium disilicate ceramic for dental applications.

PubMed

Brunot-Gohin, C; Duval, J-L; Azogui, E-E; Jannetta, R; Pezron, I; Laurent-Maquin, D; Gangloff, S C; Egles, C

2013-09-01

Ceramics are widely used materials for prosthesis, especially in dental fields. Despite multiple biomedical applications, little is known about ceramic surface modifications and the resulting cell behavior at its contact. The aim of this study is to evaluate the biological response of polished versus glazed surface treatments on lithium disilicate dental ceramic. We studied a lithium disilicate ceramic (IPS e.max(®) Press, Ivoclar Vivadent) with 3 different surface treatments: raw surface treatment, hand polished surface treatment, and glazed surface treatment (control samples are Thermanox(®), Nunc). In order to evaluate the possible modulation of cell response at the surface of ceramic, we compared polished versus glazed ceramics using an organotypic culture model of chicken epithelium. Our results show that the surface roughness is not modified as demonstrated by equivalent Ra measurements. On the contrary, the contact angle θ in water is very different between polished (84°) and glazed (33°) samples. The culture of epithelial tissues allowed a very precise assessment of histocompatibility of these interfaces and showed that polished samples increased cell adhesion and proliferation as compared to glazed samples. Lithium disilicate polished ceramic provided better adhesion and proliferation than lithium disilicate glazed ceramic. Taken together, our results demonstrate for the first time, how it is possible to use simple surface modifications to finely modulate the adhesion of tissues. Our results will help dental surgeons to choose the most appropriate surface treatment for a specific clinical application, in particular for the ceramic implant collar. Copyright © 2013 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Finite element analysis as a design tool for thermoplastic vulcanizate glazing seals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gase, K.M.; Hudacek, L.L.; Pesevski, G.T.

1998-12-31

There are three materials that are commonly used in commercial glazing seals: EPDM, silicone and thermoplastic vulcanizates (TPVs). TPVs are a high performance class of thermoplastic elastomers (TPEs), where TPEs have elastomeric properties with thermoplastic processability. TPVs have emerged as materials well suited for use in glazing seals due to ease of processing, economics and part design flexibility. The part design and development process is critical to ensure that the chosen TPV provides economics, quality and function in demanding environments. In the design and development process, there is great value in utilizing dual durometer systems to capitalize on the benefitsmore » of soft and rigid materials. Computer-aided design tools, such as Finite Element Analysis (FEA), are effective in minimizing development time and predicting system performance. Examples of TPV glazing seals will illustrate the benefits of utilizing FEA to take full advantage of the material characteristics, which results in functional performance and quality while reducing development iterations. FEA will be performed on two glazing seal profiles to confirm optimum geometry.« less

49 CFR 392.62 - Safe operation, buses.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Transportation Other Regulations Relating to Transportation (Continued) FEDERAL MOTOR CARRIER SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION FEDERAL MOTOR CARRIER SAFETY REGULATIONS DRIVING OF COMMERCIAL MOTOR VEHICLES Prohibited Practices § 392.62 Safe operation, buses. No person shall drive a bus and a motor...

Analysis of the Microstructure and Thermal Shock Resistance of Laser Glazed Nanostructured Zirconia TBCs

NASA Astrophysics Data System (ADS)

Chen, Hui; Hao, Yunfei; Wang, Hongying; Tang, Weijie

2010-03-01

Nanostructured zirconia thermal barrier coatings (TBCs) have been prepared by atmospheric plasma spraying using the reconstituted nanosized yttria partially stabilized zirconia powder. Field emission scanning electron microscope was applied to examine the microstructure of the resulting TBCs. The results showed that the TBCs exhibited a unique, complex structure including nonmelted or partially melted nanosized particles and columnar grains. A CO2 continuous wave laser beam has been applied to laser glaze the nanostructured zirconia TBCs. The effect of laser energy density on the microstructure and thermal shock resistance of the as-glazed coatings has been systematically investigated. SEM observation indicated that the microstructure of the as-glazed coatings was very different from the microstructure of the as-sprayed nanostructured TBCs. It changed from single columnar grain to a combination of columnar grains in the fracture surface and equiaxed grains on the surface with increasing laser energy density. Thermal shock resistance tests have showed that laser glazing can double the lifetime of TBCs. The failure of the as-glazed coatings was mainly due to the thermal stress caused by the thermal expansion coefficient mismatch between the ceramic coat and metallic substrate.

49 CFR 571.205(a) - Glazing equipment manufactured before September 1, 2006 and glazing materials used in vehicles...

Code of Federal Regulations, 2010 CFR

2010-10-01

... vehicle windows for driver visibility, and to minimize the possibility of occupants being thrown through the vehicle windows in collisions. S3. Application. This standard applies to glazing equipment...) [Reserved] (j) Windows and doors in motor homes, except for the windshield and windows to the immediate...

Chemical Composition of Ceramic Tile Glazes

NASA Astrophysics Data System (ADS)

Anufrik, S. S.; Kurian, N. N.; Zhukova, I. I.; Znosko, K. F.; Belkov, M. V.

2016-11-01

We have carried out laser emission and x-ray fluorescence spectral analysis of glaze before and after its application to ceramic tile produced by Keramin JSC (Belarus). We have studied the internal microstructure of the ceramic samples. It was established that on the surface and within the bulk interior of all the samples, there are micropores of sizes ranging from a few micrometers to tens of micrometers and microcracks as long as several hundred micrometers. The presence of micropores on the surface of the ceramic tile leads to an increase in the water absorption level and a decrease in frost resistance. It was found that a decrease in the surface tension of ceramic tile coatings is promoted by substitution of sodium by potassium, silica by boric anhydride, magnesium and barium by calcium, CaO by sodium oxide, and SiO2 by chromium oxide. We carried out a comparative analysis of the chemical composition of glaze samples using S4 Pioneer and ElvaX x-ray fluorescence spectrometers and also an LIBS laser emission analyzer.

24 CFR 3280.113 - Glass and glazed openings.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Glass and glazed openings. (a) Windows and sliding glass doors. All windows and sliding glass doors shall meet the requirements of § 3280.403 the “Standard for Windows and Sliding Glass Doors Used in...

Characterization of Ice Roughness Variations in Scaled Glaze Icing Conditions

NASA Technical Reports Server (NTRS)

McClain, Stephen T.; Vargas, Mario; Tsao, Jen-Ching

2016-01-01

Because of the significant influence of surface tension in governing the stability and breakdown of the liquid film in flooded stagnation regions of airfoils exposed to glaze icing conditions, the Weber number is expected to be a significant parameter governing the formation and evolution of ice roughness. To investigate the influence of the Weber number on roughness formation, 53.3-cm (21-in.) and 182.9-cm (72-in.) NACA 0012 airfoils were exposed to flow conditions with essentially the same Weber number and varying stagnation collection efficiency to illuminate similarities of the ice roughness created on the different airfoils. The airfoils were exposed to icing conditions in the Icing Research Tunnel (IRT) at the NASA Glenn Research Center. Following exposure to the icing event, the airfoils were then scanned using a ROMER Absolute Arm scanning system. The resulting point clouds were then analyzed using the self-organizing map approach of McClain and Kreeger (2013) to determine the spatial roughness variations along the surfaces of the iced airfoils. The roughness characteristics on each airfoil were then compared using the relative geometries of the airfoil. The results indicate that features of the ice shape and roughness such as glaze-ice plateau limits and maximum airfoil roughness were captured well by Weber number and collection efficiency scaling of glaze icing conditions. However, secondary ice roughness features relating the instability and waviness of the liquid film on the glaze-ice plateau surface are scaled based on physics that were not captured by the local collection efficiency variations.

Determination of Thermal Transmittance of Insulated Double Low-E Glazing Panel Using Portable Uglass Measuring Technique

NASA Astrophysics Data System (ADS)

Kim, Inkoo; Frenzl, Alexander; Kim, Taehan; Min, Steven; Blumm, Jürgen

2018-01-01

Windows are regarded as the primary object of energy efficiency in buildings because window is one of the major energy loss areas in building construction. Existing methods were not field measurements and were not enough to get the correct thermal transmittance. We used portable Ug measuring device on field and measured the thermal transmittance with low-E coated and uncoated double glazing panels in existing houses, apartments and buildings. In addition, we prepared four test benches and compared the insulation performance according to the construction conditions. In results, the insulation performance of double glazing panel with low-E coating is up to about 41 % higher than uncoated panel due to low-E coating inside and the glazing panel filled with about 90 % of argon gas decrease about 0.15 W \\cdot m^{-2} \\cdot K^{-1} than glazing panel filled with air gas. The measured results were compared with the theoretically calculated results according to DIN EN 673 to confirm the reliability of the analytical results. In this study, portable NETZSCH Uglass is used to increase the accuracy of calculation of thermal transmittance with various double and triple glazing panels. The paper analyzes the insulation performance of the double glazing panels in accordance with the construction conditions.

Evaluation of green tea extract as a glazing material for shrimp frozen by cryogenic freezing.

PubMed

Sundararajan, Srijanani; Prudente, Alfredo; Bankston, J David; King, Joan M; Wilson, Paul; Sathivel, Subramaniam

2011-09-01

Solutions of green tea (Camellia sinensis) extract (GTE) in distilled water were evaluated as a glazing material for shrimp frozen by cryogenic freezing. Total of 2%, 3%, and/or 5% GTE solutions (2GTE, 3GTE, 5GTE) were used for glazing. Distilled water glazed (GDW) and nonglazed shrimp (NG) served as controls. The GTE was characterized by measuring color, pH, (o) Brix, total phenols, and % antiradical activity. Individual catechins were identified by HPLC. The freezing time, freezing rate, and energy removal rate for freezing shrimp by cryogenic freezing process were estimated. The frozen shrimp samples were stored in a freezer at -21 °C for 180 d. Samples were analyzed for pH, moisture content, glazing yield, thaw yield, color, cutting force, and thiobarbituric acid reactive substances (TBARS) after 1, 30, 90, and 180 d. The HPLC analysis of GTE revealed the presence of catechins and their isomers and the total polyphenol content was 148.10 ± 2.49 g/L. The freezing time (min) and energy removal rate (J/s) were 48.67 ± 2.3 and 836.67 ± 78.95, respectively. Glazed samples had higher moisture content compared to NG shrimp after 180 d storage. GTE was effective in controlling the lipid oxidation in shrimp. Glazing with GTE affected a* and b* color values, but had no significant effect on the L* values of shrimp. © 2011 Institute of Food Technologists®

Window Glazing Types | Efficient Windows Collaborative

Science.gov Websites

of glass. Single Clear Single Tint Double Glazing The following sections on high-performance double fills. Double Clear Double Tint Double High-Solar-Gain Low-E Double Medium-Solar-Gain Low-E Double Low -Solar-Gain Low-E Double High-Solar-Gain Low-E with Roomside (4th surface) Low-E Double Medium-Solar-Gain

Fabricate-On-Demand Vacuum Insulating Glazings

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCamy, James W.

PPG proposed to design a fabricate-on-demand manufacturing process to overcome the cost and supply chain issues preventing widespread adoption of vacuum insulated glazing (VIG) units. To do so, we focused on improving three areas of VIG manufacturing that drive high costs and limit the ability for smaller manufacturers to enter the market: edge sealing, pillar design/placement, and evacuating the VIG.

Extent of Low-accumulation 'Wind Glaze' Areas on the East Antarctic Plateau: Implications for Continental Ice Mass Balance

NASA Technical Reports Server (NTRS)

Scambos, Theodore A.; Frezzotti, Massimo; Haran, T.; Bohlander, J.; Lenaerts, J. T. M.; Van Den Broeke, M. R.; Jezek, K.; Long, D.; Urbini, S.; Farness, K.;

End-to-End Demonstrator of the Safe Affordable Fission Engine (SAFE) 30: Power Conversion and Ion Engine Operation

NASA Technical Reports Server (NTRS)

Hrbud, Ivana; VanDyke, Melissa; Houts, Mike; Goodfellow, Keith; Schafer, Charles (Technical Monitor)

2001-01-01

The Safe Affordable Fission Engine (SAFE) test series addresses Phase 1 Space Fission Systems issues in particular non-nuclear testing and system integration issues leading to the testing and non-nuclear demonstration of a 400-kW fully integrated flight unit. The first part of the SAFE 30 test series demonstrated operation of the simulated nuclear core and heat pipe system. Experimental data acquired in a number of different test scenarios will validate existing computational models, demonstrated system flexibility (fast start-ups, multiple start-ups/shut downs), simulate predictable failure modes and operating environments. The objective of the second part is to demonstrate an integrated propulsion system consisting of a core, conversion system and a thruster where the system converts thermal heat into jet power. This end-to-end system demonstration sets a precedent for ground testing of nuclear electric propulsion systems. The paper describes the SAFE 30 end-to-end system demonstration and its subsystems.

New milarite/osumilite-type phase formed during ancient glazing of an Egyptian scarab

NASA Astrophysics Data System (ADS)

Artioli, G.; Angelini, I.; Nestola, F.

2013-02-01

A scarab found in grave 25 of the Monte Prama necropolis, near Cabras, Oristano, Sardinia, is of special importance for the archaeological interpretation and dating of this important archaeological site. The object has been misinterpreted in the past as composed by bone: recent archaeometric analyses showed that it is a glazed steatite of Egyptian origin and that the altered surface contains interesting phases crystallized during the high-temperature interaction of the Mg-rich talc core with the alkali-rich glass used for glazing. A novel single crystal X-ray diffraction analysis of one of the phases indicates that it is a new compound having the milarite-osumilite structure type, with a peculiar composition close to (Na1.52K0.12□0.36)(Mg3)(Mg1.72Cu0.16Fe0.12)(Si11.4Al0.6)O30, not reported for naturally occurring minerals. The structural and crystal chemical features of the compound, together with the known high-temperature stability of the series, allow a complete interpretation of the glazing process and conditions, based on direct application of the glaze on the steatite core with subsequent treatment at temperatures above 1000 °C.

The effect of glazing and aging on the surface properties of CAD/CAM resin blocks

PubMed Central

Tuncer, Safa; Kara, Dilan; Demirci, Mustafa

2018-01-01

PURPOSE To investigate the effect of accelerated aging on surface properties of glazed CAD/CAM resin blocks using a 2D surface profilometer and a 3D non-contact optical profilometer. MATERIALS AND METHODS Three types of CAD/CAM resin restorative materials, LAVA Ultimate (3M ESPE, St Paul, MN, USA), VITA Enamic (Vita Zahnfabrik H. Rauter, Bad Säckingen, Germany), and Cerasmart (GC Corparation, Tokyo, Japan) were used for this study. CAD/CAM blocks were cut in 3-mm thickness slabs and divided into three groups; Group 1: control group (specimens polished with 600 grit SCI paper); Group 2: specimens sandblasted, silanized, and glazed with Optiglaze Color (GC); Group 3: glazed specimens subjected to 5000 thermocycles (n=15). The surface roughness (Ra and Rz) was evaluated using a profilometer and a 3D scanning instrument. Data were analyzed using two-way ANOVA and Tukey's post-hoc test (P<.05). RESULTS LAVA, VITA, and Cerasmart exhibited statistically similar Ra and Rz values for each group (P>.05). For VITA and Cerasmart, the specimens in Group 1 exhibited significantly higher Ra values than Group 2 (P<.05). Group 1 (0.502 Ra), Group 2 (0.384 Ra), and Group 3 (0.431 Ra) exhibited statistically similar Ra values for LAVA (P=.062). After 5000 thermocycles, surface roughness values did not change significantly for glazed LAVA, VITA, and Cerasmart (P>.05). CONCLUSION Glaze material Optiglaze Color makes CAD/CAM resin surfaces smooth and glazed CAD/CAM surfaces seem resistant to deterioration under 5000 thermocycles. PMID:29503714

The effect of glazing and aging on the surface properties of CAD/CAM resin blocks.

PubMed

Tekçe, Neslihan; Fidan, Sinan; Tuncer, Safa; Kara, Dilan; Demirci, Mustafa

2018-02-01

To investigate the effect of accelerated aging on surface properties of glazed CAD/CAM resin blocks using a 2D surface profilometer and a 3D non-contact optical profilometer. Three types of CAD/CAM resin restorative materials, LAVA Ultimate (3M ESPE, St Paul, MN, USA), VITA Enamic (Vita Zahnfabrik H. Rauter, Bad Säckingen, Germany), and Cerasmart (GC Corparation, Tokyo, Japan) were used for this study. CAD/CAM blocks were cut in 3-mm thickness slabs and divided into three groups; Group 1: control group (specimens polished with 600 grit SCI paper); Group 2: specimens sandblasted, silanized, and glazed with Optiglaze Color (GC); Group 3: glazed specimens subjected to 5000 thermocycles (n=15). The surface roughness (R a and R z ) was evaluated using a profilometer and a 3D scanning instrument. Data were analyzed using two-way ANOVA and Tukey's post-hoc test ( P <.05). LAVA, VITA, and Cerasmart exhibited statistically similar R a and R z values for each group ( P >.05). For VITA and Cerasmart, the specimens in Group 1 exhibited significantly higher R a values than Group 2 ( P <.05). Group 1 (0.502 R a ), Group 2 (0.384 R a ), and Group 3 (0.431 R a ) exhibited statistically similar R a values for LAVA ( P =.062). After 5000 thermocycles, surface roughness values did not change significantly for glazed LAVA, VITA, and Cerasmart ( P >.05). Glaze material Optiglaze Color makes CAD/CAM resin surfaces smooth and glazed CAD/CAM surfaces seem resistant to deterioration under 5000 thermocycles.

Transient Approximation of SAFE-100 Heat Pipe Operation

NASA Technical Reports Server (NTRS)

Bragg-Sitton, Shannon M.; Reid, Robert S.

2005-01-01

Engineers at Los Alamos National Laboratory (LANL) have designed several heat pipe cooled reactor concepts, ranging in power from 15 kWt to 800 kWt, for both surface power systems and nuclear electric propulsion systems. The Safe, Affordable Fission Engine (SAFE) is now being developed in a collaborative effort between LANL and NASA Marshall Space Flight Center (NASA/MSFC). NASA is responsible for fabrication and testing of non-nuclear, electrically heated modules in the Early Flight Fission Test Facility (EFF-TF) at MSFC. In-core heat pipes must be properly thawed as the reactor power starts. Computational models have been developed to assess the expected operation of a specific heat pipe design during start-up, steady state operation, and shutdown. While computationally intensive codes provide complete, detailed analyses of heat pipe thaw, a relatively simple. concise routine can also be applied to approximate the response of a heat pipe to changes in the evaporator heat transfer rate during start-up and power transients (e.g., modification of reactor power level) with reasonably accurate results. This paper describes a simplified model of heat pipe start-up that extends previous work and compares the results to experimental measurements for a SAFE-100 type heat pipe design.

Potential flow analysis of glaze ice accretions on an airfoil

NASA Technical Reports Server (NTRS)

Zaguli, R. J.

1984-01-01

The results of an analytical/experimental study of the flow fields about an airfoil with leading edge glaze ice accretion shapes are presented. Tests were conducted in the Icing Research Tunnel to measure surface pressure distributions and boundary layer separation reattachment characteristics on a general aviation wing section to which was affixed wooden ice shapes which approximated typical glaze ice accretions. Comparisons were made with predicted pressure distributions using current airfoil analysis codes as well as the Bristow mixed analysis/design airfoil panel code. The Bristow code was also used to predict the separation reattachment dividing streamline by inputting the appropriate experimental surface pressure distribution.

Permanent transparent color-warming glazes for dimmable and non-dimmable LED bulbs

NASA Astrophysics Data System (ADS)

Spanard, Jan-Marie A.

2014-02-01

Illuminant metameric failure is frequently experienced when viewing material samples under LED generated light vs. traditional incandescent light. LED light temperatures can be improved with phosphor coatings, but long-wave red light is still generally absent in LED "warm-white" light, resulting in metameric failure of orange-to-red objects. Drawing on techniques developed for the architectural restoration of stained glass, we find that transparent, heat-resistant, permanent, pigmented coatings can be applied to any glass, aluminum or plastic surface of an LED bulb, including the phosphor plate, dome or envelope, to produce warmer visible light than in current warm-light LED bulbs. These glazes can be applied in combination with existing technologies to better tune the LED emitted light or they may be used alone. These pigmented coatings include, but are not limited to, those made by suspending inorganic materials in potassium silicates or durable transparent pigmented resins. The pigmented resin glazes may be produced in either a clear gloss vehicle or an iridescent, light diffusing transparent base. Further, a graduated density of the tinted glazes on dimmable bulbs allow the light to change color as wattage is diminished. The glazes may be applied in the manufacturing of the bulb or marketed to current bulb owners as an after-market product to better tune the thousands of LED light bulbs currently in use.

[Tuna (Thunnus thynnus) glazed with hydrocolloids as alternative of edible coatings and storaged at -10 degrees C].

PubMed

Mena, Sarahi; Rodriguez, Leonardo; Barrero, Marinela

2010-09-01

Numerous studies have been focused to natural ingredients to maintain the quality and shell life of foods. Edibles coating, biodegradable ingredients, such as hydrocolloids and proteins can be used for coating fish with the purpose to suppress changes of quality during frozen storage. At the present time several developing of edibles packing, like glaze using hydrocolloids, (gelatin, carrageen, starch), that besides acts as protective film for food, they are economic, can be ingested by the consumer without toxicity risk, help to preserve organoleptics and nutritional characteristics of the product and, being biodegradable they contribute to the conservation of the atmosphere. The objective of the present study was to evaluate the incorporation ofhydrocolloids in the glazing tuna process as alternative of packing, to enhance its physical and chemical characteristics. Samples of tuna was glazed incorporating to its solutions of carrageen at 0.05, 0,1 and 0.15%, and gelatin at 0.5, 1%. The samples were shaped as square (15 cm3), frozen al -30 degrees C and glazed incorporating hydrocolloids submerging the sample its solutions at 0 degrees C by 30 seconds and storage at -10 degrees C by 0, 15 and 30 days. Proximal analysis results, soluble proteins, TBA, and color showed that all the samples glazed with hydrocolloids decrease deterioration of the tuna products respect to samples glazed without hydrocolloids; concluding that glazing adding hydrocolloids protects tuna for loss humidity and delays degradation of proteins. Moreover, carrageen shows to a better performance at the concentrations of 0.05% compared with the gelatin and the starch.

Deformed Shape Analysis of Coupled Glazing Systems

DTIC Science & Technology

2013-09-01

Tyndall Air Force Base, Florida, USA ABSTRACT Glazing in storefront and curtain wall configurations is increasingly used in areas subjected to... AIR FORCE CIVIL ENGINEER CENTER READINESS DIRECTORATE  Requirements & Acquisition Division  United States Air Force  Tyndall Air Force...Antonio, Texas; %Omaha, Nebraska #Jacobs Technology, Fort Walton Beach, Florida Air Force Civil Engineer Center Readiness Directorate Requirements

The Influence of Glazing Systems on the Energy Performance of Low-Rise Commercial Buildings.

DTIC Science & Technology

1985-05-01

calculating the solar flux through the glazing system, the overall transmittance and absorptance of each layer as a function of the angle of...SYSTEM CHARACTERISTICS ...... ............... 16 3.1 Solar Optical Properties .... ............. 16 3.2 Heat Transfer_.. ...... ............... 18 3.3...building types, carries through to the occupancy characteristics and internal loading assignments. Solar glazing film has been studied (Treado,et al.,1983b

Wear characteristics of polished and glazed lithium disilicate ceramics opposed to three ceramic materials.

PubMed

Saiki, Osamu; Koizumi, Hiroyasu; Akazawa, Nobutaka; Kodaira, Akihisa; Okamura, Kentaro; Matsumura, Hideo

2016-01-01

This study compared the wear characteristics of a heat-pressed lithium disilicate ceramic material opposed to feldspathic porcelain, a lithium disilicate glass ceramic, and zirconia materials. Ceramic plate specimens were prepared from feldspathic porcelain (EX-3 nA1B), lithium disilicate glass ceramics (e.max CAD MO1/C14), and zirconia (Katana KT 10) and then ground or polished. Rounded rod specimens were fabricated from heat-pressed lithium disilicate glass ceramic (e.max press LT A3) and then glazed or polished. A sliding wear testing apparatus was used for wear testing. Wear of glazed rods was greater than that of polished rods when they were abraded with ground zirconia, ground porcelain, polished porcelain, or polished lithium disilicate ceramics. For both glazed and polished rods, wear was greater when the rods were abraded with ground plates. The findings indicate that application of a polished surface rather than a glazed surface is recommended for single restorations made of heat-pressed lithium disilicate material. In addition, care must be taken when polishing opposing materials, especially those used in occlusal contact areas. (J Oral Sci 58, 117-123, 2016).

Safe operating conditions for NSLS-II Storage Ring Frontends commissioning

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seletskiy, S.; Amundsen, C.; Ha, K.

2015-04-02

The NSLS-II Storage Ring Frontends are designed to safely accept the synchrotron radiation fan produced by respective insertion device when the electron beam orbit through the ID is locked inside the predefined Active Interlock Envelope. The Active Interlock is getting enabled at a particular beam current known as AI safe current limit. Below such current the beam orbit can be anywhere within the limits of the SR beam acceptance. During the FE commissioning the beam orbit is getting intentionally disturbed in the particular ID. In this paper we explore safe operating conditions for the Frontends commissioning.

Operationalizing safe operating space for regional social-ecological systems.

PubMed

Hossain, Md Sarwar; Dearing, John A; Eigenbrod, Felix; Johnson, Fiifi Amoako

2017-04-15

This study makes a first attempt to operationalize the safe operating space concept at a regional scale by considering the complex dynamics (e.g. non-linearity, feedbacks, and interactions) within a systems dynamic model (SD). We employ the model to explore eight 'what if' scenarios based on well-known challenges (e.g. climate change) and current policy debates (e.g. subsidy withdrawal). The findings show that the social-ecological system in the Bangladesh delta may move beyond a safe operating space when a withdrawal of a 50% subsidy for agriculture is combined with the effects of a 2°C temperature increase and sea level rise. Further reductions in upstream river discharge in the Ganges would push the system towards a dangerous zone once a 3.5°C temperature increase was reached. The social-ecological system in Bangladesh delta may be operated within a safe space by: 1) managing feedback (e.g. by reducing production costs) and the slow biophysical variables (e.g. temperature, rainfall) to increase the long-term resilience, 2) negotiating for transboundary water resources, and 3) revising global policies (e.g. withdrawal of subsidy) that negatively impact at regional scales. This study demonstrates how the concepts of tipping points, limits to adaptations, and boundaries for sustainable development may be defined in real world social-ecological systems. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

Illustration of compositional variations over time of Chinese porcelain glazes combining micro-X-ray Fluorescence spectrometry, multivariate data analysis and Seger formulas

NASA Astrophysics Data System (ADS)

Van Pevenage, J.; Verhaeven, E.; Vekemans, B.; Lauwers, D.; Herremans, D.; De Clercq, W.; Vincze, L.; Moens, L.; Vandenabeele, P.

2015-01-01

In this research, the transparent glaze layers of Chinese porcelain samples were investigated. Depending on the production period, these samples can be divided into two groups: the samples of group A dating from the Kangxi period (1661-1722), and the samples of group B produced under emperor Qianlong (1735-1795). Due to the specific sample preparation method and the small spot size of the X-ray beam, investigation of the transparent glaze layers is enabled. Despite the many existing research papers about glaze investigations of ceramics and/or porcelain ware, this research reveals new insights into the glaze composition and structure of Chinese porcelain samples. In this paper it is demonstrated, using micro-X-ray Fluorescence (μ-XRF) spectrometry, multivariate data analysis and statistical analysis (Hotelling's T-Square test) that the transparent glaze layers of the samples of groups A and B are significantly different (95% confidence level). Calculation of the Seger formulas, enabled classification of the glazes. Combining all the information, the difference in composition of the Chinese porcelain glazes of the Kangxi period and the Qianlong period can be demonstrated.

Fourier analysis of conductive heat transfer for glazed roofing materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roslan, Nurhana Lyana; Bahaman, Nurfaradila; Almanan, Raja Noorliyana Raja

For low-rise buildings, roof is the most exposed surface to solar radiation. The main mode of heat transfer from outdoor via the roof is conduction. The rate of heat transfer and the thermal impact is dependent on the thermophysical properties of roofing materials. Thus, it is important to analyze the heat distribution for the various types of roofing materials. The objectives of this paper are to obtain the Fourier series for the conductive heat transfer for two types of glazed roofing materials, namely polycarbonate and polyfilled, and also to determine the relationship between the ambient temperature and the conductive heatmore » transfer for these materials. Ambient and surface temperature data were collected from an empirical field investigation in the campus of Universiti Teknologi MARA Shah Alam. The roofing materials were installed on free-standing structures in natural ventilation. Since the temperature data are generally periodic, Fourier series and numerical harmonic analysis are applied. Based on the 24-point harmonic analysis, the eleventh order harmonics is found to generate an adequate Fourier series expansion for both glazed roofing materials. In addition, there exists a linear relationship between the ambient temperature and the conductive heat transfer for both glazed roofing materials. Based on the gradient of the graphs, lower heat transfer is indicated through polyfilled. Thus polyfilled would have a lower thermal impact compared to polycarbonate.« less

Estimating the Injury-Reducing Benefits of Ejection-Mitigating Glazing

DOT National Transportation Integrated Search

1996-02-01

The Advanced Glazing Project of NHTSA is an initiative aimed at reducing the : number of fatalities and serious injuries in motor vehicle crashes due to : ejection. As part of the project, it was necessary to estimate the numbers of : lives saved and...

32 CFR 700.857 - Safe navigation and regulations governing operation of ships and aircraft.

Code of Federal Regulations, 2013 CFR

2013-07-01

... OFFICIAL RECORDS The Commanding Officer Commanding Officers Afloat § 700.857 Safe navigation and regulations governing operation of ships and aircraft. (a) The commanding officer is responsible for the safe... Operations or the Commandant of the Marine Corps, as appropriate. (d) The Commanding Officer is responsible...

32 CFR 700.857 - Safe navigation and regulations governing operation of ships and aircraft.

Code of Federal Regulations, 2010 CFR

2010-07-01

... OFFICIAL RECORDS The Commanding Officer Commanding Officers Afloat § 700.857 Safe navigation and regulations governing operation of ships and aircraft. (a) The commanding officer is responsible for the safe... Operations or the Commandant of the Marine Corps, as appropriate. (d) The Commanding Officer is responsible...

32 CFR 700.857 - Safe navigation and regulations governing operation of ships and aircraft.

Code of Federal Regulations, 2011 CFR

2011-07-01

... OFFICIAL RECORDS The Commanding Officer Commanding Officers Afloat § 700.857 Safe navigation and regulations governing operation of ships and aircraft. (a) The commanding officer is responsible for the safe... Operations or the Commandant of the Marine Corps, as appropriate. (d) The Commanding Officer is responsible...

32 CFR 700.857 - Safe navigation and regulations governing operation of ships and aircraft.

Code of Federal Regulations, 2014 CFR

2014-07-01

... OFFICIAL RECORDS The Commanding Officer Commanding Officers Afloat § 700.857 Safe navigation and regulations governing operation of ships and aircraft. (a) The commanding officer is responsible for the safe... Operations or the Commandant of the Marine Corps, as appropriate. (d) The Commanding Officer is responsible...

32 CFR 700.857 - Safe navigation and regulations governing operation of ships and aircraft.

Code of Federal Regulations, 2012 CFR

2012-07-01

... OFFICIAL RECORDS The Commanding Officer Commanding Officers Afloat § 700.857 Safe navigation and regulations governing operation of ships and aircraft. (a) The commanding officer is responsible for the safe... Operations or the Commandant of the Marine Corps, as appropriate. (d) The Commanding Officer is responsible...

Mineralogical Characterization of Hispano-Moresque Glazes: A µ-Raman and Scanning Electron Microscopy with X-Ray Energy Dispersive Spectrometry (SEM-EDS) Study.

PubMed

Coentro, Susana; da Silva, Rui C; Relvas, Cátia; Ferreira, Teresa; Mirão, José; Pleguezuelo, Alfonso; Trindade, Rui; Muralha, Vânia S F

2018-06-05

This work explores the combination of µ-Raman spectroscopy and scanning electron microscopy with X-ray energy dispersive spectrometry (SEM-EDS) for the study of the glazes in 15th-16th century Hispano-Moresque architectural tiles. These are high lead glazes that can be tin-opacified or transparent, and present five colors: tin-white, cobalt-blue, copper-green, iron-amber, and manganese-brown. They are generally homogenous and mineral inclusions are mostly concentrated in the glaze-ceramic interface. Through SEM-EDS, these inclusions were observed and chemically analyzed, whereas µ-Raman allowed their identification on a molecular level. K-feldspars, wollastonite and diopside were the most common compounds, as well as cassiterite agglomerates that render the glaze opaque. Malayaite was identified in green glazes, and andradite and magnesioferrite in amber glazes. Co-Ni-ferrites were identified in blue glazes, as well as Ni-Fe-olivines. Manganese-brown is the color where most compounds were identified: bustamite, jacobsite, hausmannite, braunite, and kentrolite. Through the µ-Raman analysis of different areas in large inclusions previously observed by SEM, it was possible to identify intermediate phases that illustrate the reaction process that occurs between the color-conferring compounds and the surrounding lead glaze. Furthermore, the obtained results allowed inference of the raw materials and firing temperatures used on the manufacture of these tiles.

Analysis of elemental maps from glaze to body of ancient Chinese Jun and Ru porcelain by micro-X-ray fluorescence

NASA Astrophysics Data System (ADS)

Cheng, Lin; Li, Rongwu; Pan, Qiuli; Li, Guoxia; Zhao, Weijuan; Liu, Zhiguo

2009-01-01

The reasons how the middle layer of Ru and Jun porcelain between the glaze and body came into being are still not completely understood. Here, elemental maps from the glaze to the body of pieces of ancient Chinese Ru and Jun porcelain were analyzed by micro-X-ray fluorescence. The results show the middle layer was probably formed by the chemical composition of the glaze turning into glassy states and undergoing complex physical-chemical reactions with the body. However, the middle layer of Jun porcelain was formed by the chemical composition of the glaze turning into glassy states and then infiltrating the body at high temperatures during the firing process.

Extended glaze firing on ceramics for hard machining: Crack healing, residual stresses, optical and microstructural aspects.

PubMed

Aurélio, Iana L; Dorneles, Lucio S; May, Liliana G

2017-02-01

To evaluate the effect of extended and conventional (manufacturer-recommended) glaze firings on crack healing, residual stresses, optical characteristics and crystalline structure of four ceramics for hard machining. Rectangular specimens were obtained by sectioning densely sintered feldspathic (FEL), leucite- (LEU), lithium disilicate- (DIS), and zirconia-reinforced lithium silicate-based (ZLS) prefabricated ceramic blocks and divided into groups according to the applied glaze firing (n=5): conventional glaze/manufacturer-recommended (G), extended glaze (EG) and control/no heat treatment (C). Defects generated by indentation were analyzed by scanning electron microscopy before and after firing (n=1) to evaluate crack healing. Residual stresses were determined by the indentation technique. Color differences (ΔE) after firing were measured by CIEDE2000 formula, and translucency variations were quantified by contrast ratio. Stability of crystalline microstructure was analyzed by X-ray diffraction. Regardless of the material, EG had greater ability than G to heal defects, and produced compressive residual stresses, while G generated tensile stresses. Color differences produced by EG were: imperceptible for FEL and LEU ceramics; perceptible, but still clinically acceptable for DIS; clinically unacceptable for ZLS. G produced no perceptible color change. The DIS and ZLS ceramics became ≈1% more opaque after G, ≈4% and ≈15%, respectively, after EG. The crystalline phase of all the ceramics remained stable after G and EG. Extended glaze firing could be an alternative to finish feldspathic, leucite-, and lithium disilicate-based ceramic restorations, since it provides greater crack healing than the conventional glaze firing. It develops tolerable residual stresses, and produces clinically acceptable color alterations, without altering the microstructure of these materials. Copyright © 2016 The Academy of Dental Materials. Published by Elsevier Ltd. All rights

Simple Automatic File Exchange (SAFE) to Support Low-Cost Spacecraft Operation via the Internet

NASA Technical Reports Server (NTRS)

Baker, Paul; Repaci, Max; Sames, David

1998-01-01

Various issues associated with Simple Automatic File Exchange (SAFE) are presented in viewgraph form. Specific topics include: 1) Packet telemetry, Internet IP networks and cost reduction; 2) Basic functions and technical features of SAFE; 3) Project goals, including low-cost satellite transmission to data centers to be distributed via an Internet; 4) Operations with a replicated file protocol; 5) File exchange operation; 6) Ground stations as gateways; 7) Lessons learned from demonstrations and tests with SAFE; and 8) Feedback and future initiatives.

The art of Bernard Palissy (1510-1590): influence of firing conditions on the microstructure of iron-coloured high-lead glazes

NASA Astrophysics Data System (ADS)

Roisine, Gauthier; Capobianco, Natan; Caurant, Daniel; Wallez, Gilles; Bouquillon, Anne; Majérus, Odile; Cormier, Laurent; Gilette, Solène; Gerbier, Aurélie

2017-08-01

During the French Renaissance, a well-known ceramist, Bernard Palissy (1510-1590), succeeded to create amazing lead-glazed ceramics, the recipe of which he kept totally secret. The present study is a first step to try to understand the process of manufacture of Palissy's honey iron-coloured high-lead aluminosilicate glazes through examination of both ancient glazes—discovered in Palissy's workshop (Paris, garden of Tuileries), during archaeological excavations—and replicate glazes of similar composition prepared in the laboratory from raw materials mixtures under controlled conditions (different firing temperatures T_p and cooling rates). These replicate glazes were characterised by X-ray diffraction (XRD) and scanning electron microscopy coupled with energy-dispersive spectroscopy (SEM-EDS). According to laboratory experimentations, three iron-rich crystalline phases are likely to be formed in the glaze after firing (hematite {Fe2O3}, melanotekite {Pb2Fe2Si2O9} and magnetoplumbite PbFe_{12}O_{19}) and their nature, abundance and microstructure strongly depend on both temperature T_p and cooling rate. Comparing the microstructures of replicate glazes and authentic Palissy's glazes allowed to better understand the artist technique in terms of firing process: he would have probably fired most of his production around 1000°C, above liquidus temperature, and would have used a reasonably fast cooling rate (faster than 5° C/h), which enables both to melt all raw materials and to prevent crystallisation during cooling.

Operation Safe Border: The Ecuador-Peru Crisis

DTIC Science & Technology

1996-01-01

52 JFQ / Spring 1996 In January 1995, the hemisphere was shocked by an outbreak of fighting between Ecuador and Peru over a long-festering border...Weidner, USA, is commander of the U.S. Military Group-Honduras and served as commander of the U.S. Contingent, Military Observer Mission, Ecuador ...Peru. Operation Safe Border: The Ecuador -Peru Crisis By G L E N N R. W E I D N E R Santiago River (fore- ground) and Yaupi River on Ecuador -Peru

Changes to Glazed Dental Ceramic Shade, Roughness, and Microhardness after Bleaching and Simulated Brushing.

PubMed

Rodrigues, Carlos Roberto Teixeira; Turssi, Cecilia Pedroso; Amaral, Flávia Lucisano Botelho; Basting, Roberta Tarkany; França, Fabiana Mantovani Gomes

2017-09-05

To evaluate shade stability, surface roughness, microhardness, and compressive strength of a glazed feldspathic ceramic subjected to bleaching and simulated brushing. Eighty-eight glazed feldspathic ceramic specimens were made from microparticulate leucite and divided into eight groups (n = 10). The whitening products used were: Opalescence Trèswhite Supreme (Ultradent), Opalescence®\\ PF 15% (Ultradent), and Oral-B 3D White Whitestrips. All substances for whitening were used for 4 hours/day for a period of 14 days; the control group was not bleached. Next, half of the specimens were individually brushed. Microhardness and surface roughness data were subjected to three-way ANOVA and Tukey test. The diametrical tensile strength data were subjected to two-way ANOVA. The shade change data were analyzed using Kruskal-Wallis, Mann-Whitney, and the Student-Newman-Keuls test. The significance level was set at 5%. Glazed feldspathic ceramic surface microhardness was significantly affected by bleaching agents (p = 0.007). Initially, glazed ceramic microhardness was significantly higher than that observed after contact with the bleaching agents, whether or not brushing was performed. The specimens submitted to bleaching in preloaded trays presented lower surface roughness values after brushing (p = 0.037). The surface roughness was significantly lower in the brushed specimens (p = 0.044). The diametrical tensile strength was not significantly affected by the application of bleaching agents (p = 0.563) or by brushing (p = 0.477). When the specimens were brushed, however, shade change was significantly influenced by the bleaching agent used (p = 0.041). Bleaching agents associated with brushing cycles can alter surface properties and shade stability of glazed feldspathic ceramics, though such findings may not reflect the performance of unglazed feldspathic ceramics. © 2017 by the American College of Prosthodontists.

49 CFR 571.205 - Standard No. 205, Glazing materials.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Motor Vehicle Safety Standards § 571.205 Standard No. 205, Glazing materials. S1. Scope. This standard...↓S1”, “A↓S14” and “A↑S2”. Note that the arrow indicating the portion of the material that complies... on GPO Access. ...

25. INTERIOR OF GLAZE KILN NO. 2, SHOWING HOW SAGGERS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

25. INTERIOR OF GLAZE KILN NO. 2, SHOWING HOW SAGGERS AND LOOSE QUARRY TILES WERE STACKED. - Moravian Pottery & Tile Works, Southwest side of State Route 313 (Swamp Road), Northwest of East Court Street, Doylestown, Bucks County, PA

Determination of levels of polychlorinated biphenyls (PCBs) present in caulk and window glazing material samples from older buildings

EPA Science Inventory

Levels of polychlorinated biphenyls (PCBs) in caulk and window glazing material samples from older buildings were determined, using a method developed for this purpose. This method was evaluated by analyzing a combination of 47 samples of caulk, glazing materials, including quali...

Mössbauer analysis of the firing process of the sky-green glaze of the imitative ancient Chinese Ru porcelain

NASA Astrophysics Data System (ADS)

Songhua, Chen; Zhengyao, Gao; Guoju, Hu; Xiande, Chen

1994-12-01

The variation of the Mössbauer parameters of the imitative ancient Ru porcelain skygreen glaze with the firing conditions is studied in detail in the present paper. The Mössbauer spectra show that the sky-green glaze contains three kinds of iron minerals, i.e. the structural iron (Fe2+ and Fe3+); Fe2O3 and Fe3O4. The relative intensity of the paramagnetic peak Fe2+ increases and the magnetic ratio of the magnetic peak decreases with increasing temperature. Based on the variation of the quadrupole splitting ( QS) of the paramagnetic peak Fe2+, the phase transformation characteristics of the sky-green glaze in the firing process is discussed. The coloring mechanism of the sky-green glaze and the variation of its magnetism in the firing process are also investigated in the present paper.

45. PRODUCTION AREA, GROUND FLOOR, EAST WING. GLAZE MIXING AREA ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

45. PRODUCTION AREA, GROUND FLOOR, EAST WING. GLAZE MIXING AREA IN THE RIGHT BACKGROUND, COURTYARD THROUGH THE DOORWAY TO THE LEFT. - Moravian Pottery & Tile Works, Southwest side of State Route 313 (Swamp Road), Northwest of East Court Street, Doylestown, Bucks County, PA

Rime-, mixed- and glaze-ice evaluations of three scaling laws

NASA Technical Reports Server (NTRS)

Anderson, David N.

1994-01-01

This report presents the results of tests at NASA Lewis to evaluate three icing scaling relationships or 'laws' for an unheated model. The laws were LWC x time = constant, one proposed by a Swedish-Russian group and one used at ONERA in France. Icing tests were performed in the NASA Lewis Icing Research Tunnel (IRT) with cylinders ranging from 2.5- to 15.2-cm diameter. Reference conditions were chosen to provide rime, mixed and glaze ice. Scaled conditions were tested for several scenarios of size and velocity scaling, and the resulting ice shapes compared. For rime-ice conditions, all three of the scaling laws provided scaled ice shapes which closely matched reference ice shapes. For mixed ice and for glaze ice none of the scaling laws produced consistently good simulation of the reference ice shapes. Explanations for the observed results are proposed, and scaling issues requiring further study are identified.

Planetary boundaries: exploring the safe operating space for humanity

Treesearch

Johan Rockström; Will Steffen; Kevin Noone; Asa Persson; F. Stuart Chapin; Eric Lambin; Timothy M. Lenton; Marten Scheffer; Carl Folke; Hans Joachim Schellnhuber; Björn Nykvist; Cynthia A. de Wit; Terry Hughes; Sander van der Leeuw; Henning Rodhe; Sverker Sörlin; Peter K. Snyder; Robert Costanza; Uno Svedin; Malin Falkenmark; Louise Karlberg; Robert W. Corell; Victoria J. Fabry; James Hansen; Brian Walker; Diana Liverman; Katherine Richardson; Paul Crutzen; Jonathan Foley

2009-01-01

Anthropogenic pressures on the Earth System have reached a scale where abrupt global environmental change can no longer be excluded. We propose a new approach to global sustainability in which we define planetary boundaries within which we expect that humanity can operate safely. Transgressing one or more planetary boundaries may be deleterious or even catastrophic due...

Interior view, detail to show the gold painted and glazed ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Interior view, detail to show the gold painted and glazed ceiling of the main entry lobby on Fourteenth Street; bronze chandeliers hang from this ceiling - United States Department of Commerce, Bounded by Fourteenth, Fifteenth, and E streets and Constitution Avenue, Washington, District of Columbia, DC

10. INTERIOR KITCHEN UTILITY AREA SHOWING PARTITION, PANELED AND GLAZED ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. INTERIOR KITCHEN UTILITY AREA SHOWING PARTITION, PANELED AND GLAZED REAR DOOR, AND ROW OF 6-LIGHT OVER 1-LIGHT, DOUBLE-HUNG, WOOD-FRAMED WINDOWS AROUND EAST CORNER OF HOUSE. VIEW TO EAST. - Bishop Creek Hydroelectric System, Plant 4, Worker Cottage, Bishop Creek, Bishop, Inyo County, CA

Design for Assured Safe Jettison Operations

NASA Astrophysics Data System (ADS)

Herd, Andrew; Shea, Matt

2010-09-01

The International Space Station is coming toward the end of the assembly process and will enter "steady state" operations. During this time and also in the future, there arises the need for removing items from station, and in some instances this is achieved through jettison, either robotic or crew initiated. To control this practice at the ISS Partner level, a policy document has been developed. The policy states: "While there are risks inherent in jettisoning objects, the ISS Program recognizes that there may be significant benefits in terms of operational flexibility, crew safety, etc. A thorough assessment of the risks vs. the benefits will be conducted whenever a proposal to jettison an object is made. It is the intent of the ISS Program to limit the number of objects that are jettisoned from the ISS ...". The policy addresses hardware that: "may fall into one or more of the following categories: 1. Items that pose a safety issue for the ISS or for return onboard a visiting vehicle(contamination, materials degradation, etc.) 2. Items that negatively impact ISS utilization, return or on-orbit stowage manifests 3. Items that represent an Extravehicular Activity(EVA) timeline savings large enough to reduce the sum of the risks of EVA exposure time and the orbital environment’s hazardous debris population, compared to the sum of such risks without a jettison. 4. Items that are designed for jettison ". [1] Through the use of jettison to date, as a disposal means, operational experiences have been gained during and as a result of post-disposal event analysis. The data collected has allowed a generic assessment of issues(and best practices) and the proposal of ways in which process corrective action can be taken to assure future safe jettison operations. The improvements proposed emphasize the ways in which design can offer key interface and hardware response characteristics to the jettison event and the subsequent orbital and re-entry profile. There exist simple

Energy Conservation Strategies for Windows and Glazed Surfaces

DTIC Science & Technology

1998-07-01

When activated, photochromies reduce only the visual transmittance, not the infrared, so much of the solar heat gain is unaffected. • Thermochromic ...Strategies Windows and Glazed Surfaces by Brian M. Deal, Robert J. Nemeth, and Lee P. DeBaille for Solar Radiation Reflected Transmitted Absorbed...10 Fenestration Design 12 3 Heat Transfer Fundamentals 14 Mechanisms of Heat Transfer 14 Heat Transfer Process Through Glass 16 Solar Heat Gain

[Environmental lead poisoning from lead-glazed earthenware used for storing drinks].

PubMed

Sabouraud, S; Coppéré, B; Rousseau, C; Testud, F; Pulce, C; Tholly, F; Blanc, M; Culoma, F; Facchin, A; Ninet, J; Chambon, P; Medina, B; Descotes, J

2009-12-01

Current unusual environmental sources of lead exposure mainly include traditional medicines, either ayurvedic remedies or others, traditional cosmetics (kohl, surma), and the use of traditional earthenware, for storage or cooking. We report two cases of lead poisoning in adults initially identified by paroxysmal abdominal pain or anemia. In both cases, the environmental investigation evidenced one main source of lead exposure, namely a lead-glazed earthenware jug in which a drink was stored, "kefir" in the first case, and "kombucha" tea in the second one. It is recommended to search for lead intoxication in patients with unexplained anemia. Environmental sources of lead can be multiple. Their relative importance has to be ranked during the environmental investigation and among these, lead-glazed earthenware must be considered as a source of high lead exposure when drinks are stored inside and thus can soak.

Water Droplet Impingement on Simulated Glaze, Mixed, and Rime Ice Accretions

NASA Technical Reports Server (NTRS)

Papadakis, Michael; Rachman, Arief; Wong, See-Cheuk; Yeong, Hsiung-Wei; Hung, Kuohsing E.; Vu, Giao T.; Bidwell, Colin S.

2007-01-01

Water droplet impingement data were obtained at the NASA Glenn Icing Research Tunnel (IRT) for a 36-in. chord NACA 23012 airfoil with and without simulated ice using a dye-tracer method. The simulated ice shapes were defined with the NASA Glenn LEWICE 2.2 ice accretion program and including one rime, four mixed and five glaze ice shapes. The impingement experiments were performed with spray clouds having median volumetric diameters of 20, 52, 111, 154, and 236 micron. Comparisons to the experimental data were generated which showed good agreement for the rime and mixed shapes at lower drop sizes. For larger drops sizes LEWICE 2.2 over predicted the collection efficiencies due to droplet splashing effects which were not modeled in the program. Also for the more complex glaze ice shapes interpolation errors resulted in the over prediction of collection efficiencies in cove or shadow regions of ice shapes.

Cost-efficient manufacturing process of switchable glazing based on twisted nematic LC cells

NASA Astrophysics Data System (ADS)

Kurz, Eberhard; Rau, Lothar; Frühauf, Norbert; Haase, Walter; Prskalo, Marijo; Sobek, Werner

2011-10-01

Large-area glass facades are widely spread in contemporary architecture. They meet demands for natural light illumination of rooms and satisfy esthetic requirements of modern architecture. However, larger glass facades increase transfer of energy into the building. Since this has to be compensated by the intense use of air conditioning, modulation of the energy passing through the glazing is essential. The authors have been developing a corresponding system. It consists of a modified twisted nematic (TN) liquid crystal (LC) cell which is embedded in a double glazing. Since a conventional outside film polarizer is susceptible to heat, the authors substituted this component for an inside coatable polarizer. Long term outdoor weathering tests demonstrated that the concept is viable. Part of the current research is the integration of the TN LC cell into double-glazing. A further demand for such a system is a cost-efficient manufacturing process. It has been investigated to use the coatable polarizer at the same time as an alignment layer for the liquid crystal. Aluminum zinc oxide (AZO) is to be used for the electrode material substituting conventionally used indium tin oxide (ITO) which is expensive. Currently the authors are looking into the coating process for the inside polarizer.

Recommended Practices for the Safe Design and Operation of Flywheels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bender, Donald Arthur

2015-12-01

Flywheel energy storage systems are in use globally in increasing numbers . No codes pertaining specifically to flywheel energy storage exist. A number of industrial incidents have occurred. This protocol recommends a technical basis for safe flywheel de sign and operation for consideration by flywheel developers, users of flywheel systems and standards setting organizations.

The effect of single-horn glaze ice on the vortex structures in the wake of a horizontal axis wind turbine

NASA Astrophysics Data System (ADS)

Jin, Zhe-Yan; Dong, Qiao-Tian; Yang, Zhi-Gang

2015-02-01

The present study experimentally investigated the effect of a simulated single-horn glaze ice accreted on rotor blades on the vortex structures in the wake of a horizontal axis wind turbine by using the stereoscopic particle image velocimetry (Stereo-PIV) technique. During the experiments, four horizontal axis wind turbine models were tested, and both "free-run" and "phase-locked" Stereo-PIV measurements were carried out. Based on the "free-run" measurements, it was found that because of the simulated single-horn glaze ice, the shape, vorticity, and trajectory of tip vortices were changed significantly, and less kinetic energy of the airflow could be harvested by the wind turbine. In addition, the "phase-locked" results indicated that the presence of simulated single-horn glaze ice resulted in a dramatic reduction of the vorticity peak of the tip vortices. Moreover, as the length of the glaze ice increased, both root and tip vortex gaps were found to increase accordingly.

Electron Beam/Laser Glazing of Iron-Base Materials.

DTIC Science & Technology

1981-07-01

alloy (-l. 5wt %Cr) steels after laser and electron beam glazing. In this work it is shown that the dramatic difference in microstructure and hardness...highly alloyed tool steels can be critical in determining the complexity of the solidification route. The analyses of M2, M42 and M7 are given in...the type described in Fe- Ni alloys (1). This con- clusion is based on optical and scanning electron microscope observation unambig- uously showing

Gas impermeable glaze for sealing a porous ceramic surface

DOEpatents

Reed, Scott T.; Stone, Ronald G.; Nenoff, Tina M.; Trudell, Daniel E.; Thoma, Steven G.

2004-04-06

A process for fabricating a gas impermeable seal on a porous ceramic surface using a thin, glass-based, pinhole free glaze. The process can be used to fabricate gas impermeable end seals on porous alumina tubes used as filter media. The porous alumina tubes can have an inorganic microporous thin film separation membrane on the inner surface, which can be used for high temperature gas separation processes.

Influence of Spacer Systems on Heat Transfer in Evacuated Glazing

NASA Astrophysics Data System (ADS)

Swimm, K.; Weinläder, H.; Ebert, H.-P.

2009-06-01

One attractive possibility to essentially improve the insulation properties of glazing is to evacuate the space between the glass panes. This eliminates heat transport due to convection between the glass panes and suppresses the thermal conductivity of the remaining low pressure filling gas atmosphere. The glass panes can be prevented from collapsing by using a matrix of spacers. These spacers, however, increase heat transfer between the glass panes. To quantify this effect, heat transfer through samples of evacuated glazing was experimentally determined. The samples were prepared with different kinds of spacer materials and spacer distances. The measurements were performed with a guarded hot-plate apparatus under steady-state conditions and at room temperature. The measuring chamber of the guarded hot plate was evacuated to < 10-2 Pa. An external pressure load of 0.1 MPa was applied on the samples to ensure realistic system conditions. Radiative heat transfer was significantly reduced by preparing the samples with a low- ɛ coating on one of the glass panes. In a first step, measurements without any spacers allowed quantification of the amount of radiative heat transfer. With these data, the measurements with spacers could be corrected to separate the effect of the spacers on thermal heat transfer. The influence of the thermal conductivity of the spacer material, as well as the distance between the spacers and the spacer geometry, was experimentally investigated and showed good agreement with simulation results. For mechanically stable matrices with cylindrical spacers, experimental thermal conductance values ≤0.44W·m-2 ·K-1 were found. This shows that U g -values of about 0.5W · m-2 · K-1 are achievable in evacuated glazing, if highly efficient low-emissivity coatings are used.

Physical Mechanisms of Glaze Ice Scallop Formations on Swept Wings

NASA Technical Reports Server (NTRS)

Vargas, Mario; Reshotko, Eli

1998-01-01

An experiment was conducted to understand the physical mechanisms that lead to the formation of scallops on swept wings. Icing runs were performed on a NACA 0012 swept wing tip at 45 deg, 30 deg, and 15 deg sweep angles. A baseline case was chosen and direct measurements of scallop height and spacing, castings, video data and close-up photographic data were obtained. The results showed the scallops are made of glaze ice feathers that grow from roughness elements that have reached a minimum height and are located beyond a given distance from the attachment line. This distance depends on tunnel conditions and sweep angle, and is the critical parameter in the formation of scallops. It determines if complete scallops, incomplete scallops or no scallops are going to be formed. The mechanisms of growth for complete and incomplete scallops were identified. The effect of velocity, temperature and LWC on scallop formation was studied. The possibility that cross flow instability may be the physical mechanism that triggers the growth of roughness elements into glaze ice feathers is examined.

Data in support of energy performance of double-glazed windows.

PubMed

Shakouri, Mahmoud; Banihashemi, Saeed

2016-06-01

This paper provides the data used in a research project to propose a new simplified windows rating system based on saved annual energy ("Developing an empirical predictive energy-rating model for windows by using Artificial Neural Network" (Shakouri Hassanabadi and Banihashemi Namini, 2012) [1], "Climatic, parametric and non-parametric analysis of energy performance of double-glazed windows in different climates" (Banihashemi et al., 2015) [2]). A full factorial simulation study was conducted to evaluate the performance of 26 different types of windows in a four-story residential building. In order to generalize the results, the selected windows were tested in four climates of cold, tropical, temperate, and hot and arid; and four different main orientations of North, West, South and East. The accompanied datasets include the annual saved cooling and heating energy in different climates and orientations by using the selected windows. Moreover, a complete dataset is provided that includes the specifications of 26 windows, climate data, month, and orientation of the window. This dataset can be used to make predictive models for energy efficiency assessment of double glazed windows.

46 CFR 177.1030 - Operating station visibility.

Code of Federal Regulations, 2010 CFR

2010-10-01

... TONS) CONSTRUCTION AND ARRANGEMENT Window Construction and Visibility § 177.1030 Operating station visibility. (a) Windows and other openings at the operating station must be of sufficient size and properly... glazing material used in windows at the operating station must have a light transmission of not less than...

Unmanned Aerial Systems Traffic Management (UTM): Safely Enabling UAS Operations in Low-Altitude Airspace

NASA Technical Reports Server (NTRS)

Jung, Jaewoo; Kopardekar, Parimal H.

2016-01-01

Flexibility where possible, and structure where necessary. Consider the needs of national security, safe airspace operations, economic opportunities, and emerging technologies. Risk-based approach based on population density, assets on the ground, density of operations, etc. Digital, virtual, dynamic, and as needed UTM services to manage operations.

Unmanned Aerial Systems Traffic Management (UTM): Safely Enabling UAS Operations in Low-Altitude Airspace

NASA Technical Reports Server (NTRS)

Kopardekar, Parimal H.; Cavolowsky, John

2015-01-01

Flexibility where possible, and structure where necessary. Consider the needs of national security, safe airspace operations, economic opportunities, and emerging technologies. Risk-based approach based on population density, assets on the ground, density of operations, etc. Digital, virtual, dynamic, and as needed UTM services to manage operations.

Flexible edge seal for vacuum insulating glazing units

DOEpatents

Bettger, Kenneth J.; Stark, David H.

2012-12-11

A flexible edge seal is provided for a vacuum insulating glazing unit having a first glass pane and a second glass pane spaced-apart from the first. The edge seal comprises a seal member formed of a hermetically bondable material and having a first end, a second end and a center section disposed therebetween. The first end is hermetically bondable to a first glass pane. The second end is hermetically bondable to a second glass pane. The center section comprises a plurality of convolutes.

Cross Flow Effects on Glaze Ice Roughness Formation

NASA Technical Reports Server (NTRS)

Tsao, Jen-Ching

2004-01-01

The present study examines the impact of large-scale cross flow on the creation of ice roughness elements on the leading edge of a swept wing under glaze icing conditions. A three-dimensional triple-deck structure is developed to describe the local interaction of a 3 D air boundary layer with ice sheets and liquid films. A linear stability analysis is presented here. It is found that, as the sweep angle increases, the local icing instabilities enhance and the most linearly unstable modes are strictly three dimensional.

Microstructural stability of wrought, laser and electron beam glazed NARloy-Z alloy at elevated temperatures

NASA Technical Reports Server (NTRS)

Singh, J.; Jerman, G.; Bhat, B.; Poorman, R.

1993-01-01

Microstructure of wrought, laser, and electron-beam glazed NARloy-Z(Cu-3 wt.% Ag-0.5 wt.% Zr) was investigated for thermal stability at elevated temperatures (539 to 760 C (1,100 to 1,400 F)) up to 94 h. Optical and scanning electron microscopy and electron probe microanalysis were employed for studying microstructural evolution and kinetics of precipitation. Grain boundary precipitation and precipitate free zones (PFZ's) were observed in the wrought alloy after exposing to temperatures above 605 C (1,120 F). The fine-grained microstructure observed in the laser and electron-beam glazed NARloy-Z was much more stable at elevated temperatures. Microstructural changes correlated well with hardness measurements.

Safe Autonomous Flight Environment (SAFE50) for the Notional Last 50 ft of Operation of 55 lb Class of UAS

NASA Technical Reports Server (NTRS)

Krishnakumar, Kalmanje; Kopardekar, Parimal; Ippolito, Corey; Melton, John E.; Stepanyan, Vahram; Sankararaman, Shankar; Nikaido, Ben

2017-01-01

The most difficult phase of small Unmanned Aerial System (sUAS) deployment is autonomous operations below the notional 50 ft in urban landscapes. Understanding the feasibility of safely flying sUAS autonomously below 50 ft is a game changer for many civilian applications. This paper outlines three areas of research currently underway which address key challenges for flight in the urban landscape. These are: (1) Off-line and On-board wind estimation and accommodation; (2) Real-time trajectory planning via characterization of obstacles using a LIDAR; (3) On-board information fusion for real-time decision-making and safe trajectory generation.

Optimum Design Parameters of Box Window DSF Office at Different Glazing Types under Sub Interval of Intermediate Sky Conditions (20-40 klux)

NASA Astrophysics Data System (ADS)

Elayeb, O. K.; Alghoul, M. A.; Sopian, K.; Khrita, N. G.

2017-11-01

Despite Double skin façade (DSF) buildings are widely deployed worldwide, daylighting strategy is not commonly incorporated in these buildings compare to other strategies. Therefore, further theoretical and experimental studies would lead to adopting daylighting strategy in DSF office buildings. The aim of this study is to investigate the daylighting performance of office building at different design parameters of box window DSF using different glazing types under sub interval of intermediate sky conditions (20-40) klux using the (IES VE) simulation tool from Integrated Environmental Solutions - Virtual Environment. The implemented design parameters are window wall ratio (WWR) of internal façade (10-100) %, cavity depth (CD) of DSF (1-2.5) m and different glazing types. The glazing types were selected from the list available in the (IES VE) simulation tool. After series of evaluations, bronze tinted coating (STOPSOL) is implemented for the exterior façade while clear float, clear reflective coating (STOPSOL), grey and brown tinted coating (Anti-sun float) and blue coating tinted (SUNCOOL float) are implemented for the interior façade. In this paper, several evaluation parameters are used to quantify the optimum design parameters that would balance the daylighting requirements of a box window DSF office versus sky conditions range (20-40) klux. The optimum design parameters of DSF office building obtained under different glazing types are highlighted as follows. When using bronze tinted coating (STOPSOL) for the exterior façade, the glazing types of interior façade that showed superior daylighting performance of DSF office at (CD of 1.0m with WWR of 70%), (CD of 1.5m with WWR of 70%), (CD of 2.0m with WWR of 70%) and (CD of 2.0m with WWR of 70%) are grey tinted coating (Anti-sun float), clear reflective coating (STOPSOL), brown tinted coating (Anti-sun float), and clear float glazing respectively. Blue Coating tinted (SUNCOOL float) of interior façade glazing

49 CFR 393.62 - Emergency exits for buses.

Code of Federal Regulations, 2011 CFR

2011-10-01

... (including a school bus used in interstate commerce for non-school bus operations) with a GVWR of more than 4... manufacture. (2) Each bus (including a school bus used in interstate commerce for non-school bus operations... NECESSARY FOR SAFE OPERATION Glazing and Window Construction § 393.62 Emergency exits for buses. (a) Buses...

49 CFR 393.62 - Emergency exits for buses.

Code of Federal Regulations, 2013 CFR

2013-10-01

... (including a school bus used in interstate commerce for non-school bus operations) with a GVWR of more than 4... manufacture. (2) Each bus (including a school bus used in interstate commerce for non-school bus operations... NECESSARY FOR SAFE OPERATION Glazing and Window Construction § 393.62 Emergency exits for buses. (a) Buses...

49 CFR 393.62 - Emergency exits for buses.

Code of Federal Regulations, 2014 CFR

2014-10-01

... (including a school bus used in interstate commerce for non-school bus operations) with a GVWR of more than 4... manufacture. (2) Each bus (including a school bus used in interstate commerce for non-school bus operations... NECESSARY FOR SAFE OPERATION Glazing and Window Construction § 393.62 Emergency exits for buses. (a) Buses...

49 CFR 393.62 - Emergency exits for buses.

Code of Federal Regulations, 2012 CFR

2012-10-01

... (including a school bus used in interstate commerce for non-school bus operations) with a GVWR of more than 4... manufacture. (2) Each bus (including a school bus used in interstate commerce for non-school bus operations... NECESSARY FOR SAFE OPERATION Glazing and Window Construction § 393.62 Emergency exits for buses. (a) Buses...

Beyond climate-smart agriculture: toward safe operating spaces for global food systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gulledge, Jay; Neufeldt, Heinrich; Jahn, Margaret M

Agriculture is considered to be climate-smart when it contributes to increasing food security, adaptation and mitigation in a sustainable way. This new concept now dominates current discussions in agricultural development because of its capacity to unite the agendas of the agriculture, development and climate change communities under one brand. In this opinion piece authored by scientists from a variety of international agricultural and climate research communities, we argue that the concept needs to be evaluated critically because the relationship between the three dimensions is poorly understood, such that practically any improved agricultural practice can be considered climate-smart. This lack ofmore » clarity may have contributed to the broad appeal of the concept. From the understanding that we must hold ourselves accountable to demonstrably better meet human needs in the short and long term within foreseeable local and planetary limits, we develop a conceptualization of climate-smart agriculture as agriculture that can be shown to bring us closer to safe operating spaces for agricultural and food systems across spatial and temporal scales. Improvements in the management of agricultural systems that bring us significantly closer to safe operating spaces will require transformations in governance and use of our natural resources, underpinned by enabling political, social and economic conditions beyond incremental changes. Establishing scientifically credible indicators and metrics of long-term safe operating spaces in the context of a changing climate and growing social-ecological challenges is critical to creating the societal demand and political will required to motivate deep transformations. Answering questions on how the needed transformational change can be achieved will require actively setting and testing hypotheses to refine and characterize our concepts of safer spaces for social-ecological systems across scales. This effort will demand prioritizing

Partial Rarefaction as Way to Reduce Distortion Curve of double-glazed unit

NASA Astrophysics Data System (ADS)

Plotnikov, Alexander

2017-10-01

Use of Insulated Glass Units (IGU) as glazing on building façades causes optical distortions of mirrored images of neighboring buildings in glazed surfaces. Optical distortions are caused by varying distances between glass panes in IGUs as a result of climate factors. This paper examines available engineering solutions that reduce such distortions: use of more rigid outer glasses, encasing the building in a shell of single glass panes, known as the ‘double façade’, and use of vacuum IGUs. A new way is proposed to reduce optical distortions by installing additional pointed or linear supports and creating pre-stress with partial rarefaction inside the IGU. Overpressure that can cause IGU expansion and glass deformation was calculated. In the urban environment of Moscow, reduction of air pressure with simultaneous increase of air pressure inside the IGU during summer heat waves can be as high as 5%, and this figure determines the level of rarefaction.

Effects of small-grit grinding and glazing on mechanical behaviors and ageing resistance of a super-translucent dental zirconia.

PubMed

Lai, Xuan; Si, Wenjie; Jiang, Danyu; Sun, Ting; Shao, Longquan; Deng, Bin

2017-11-01

The purpose of this study is to elucidate the effects of small-grit grinding on the mechanical behaviors and ageing resistance of a super-translucent dental zirconia and to investigate the necessity of glazing for the small-grit ground zirconia. Small-grit grinding was performed using two kinds of silicon carbide abrasive papers. The control group received no grinding. The unground surfaces and the ground surfaces were glazed by an experienced dental technician. Finally, the zirconia materials were thermally aged in water at 134°C for 5h. After aforementioned treatments, we observed the surface topography and the microstructures, and measured the extent of monoclinic phase, the nano-hardness and nano-modulus of the possible transformed zone and the flexural strength. Small-grit grinding changed the surface topography. The zirconia microstructure did not change obviously after surface treatments and thermal ageing; however, the glaze in contact with zirconia showed cracks after thermal ageing. Small-grit grinding did not induce a phase transformation but improved the flexural strength and ageing resistance. Glazing prevented zirconia from thermal ageing but severely diminished the flexural strength. The nano-hardness and nano-modulus of the surface layer were increased by ultrafine grinding. The results suggest that small-grit grinding is beneficial to the strength and ageing resistance of the super-translucent dental zirconia; however, glazing is not necessary and even impairs the strength for the super-translucent dental zirconia. This study is helpful to the researches about dental grinding tools and maybe useful for dentists to choose reasonable zirconia surface treatments. Copyright © 2017 Elsevier Ltd. All rights reserved.

Safely Conducting Airport Surface Trajectory-Based Operations

NASA Technical Reports Server (NTRS)

Jones, Denise R.; Prinzel, Lawrence J., III; Bailey, Randall E.; Arthur, Jarvis J., III; Barnes, James R.

2014-01-01

A piloted simulation study was conducted at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) to evaluate the ability to safely conduct surface trajectory-based operations (STBO) by assessing the impact of providing traffic intent information, conflict detection and resolution (CD&R) system capability, and the display of STBO guidance to the flight crew on both head-down and head-up displays (HUD). Nominal and off-nominal conflict scenarios were conducted using 12 airline crews operating in a simulated Memphis International Airport terminal environment. The flight crews met their required time-of-arrival at route end within 10 seconds on 98 percent of the trials, well within the acceptable performance bounds of 15 seconds. Traffic intent information was found to be useful in determining the intent of conflict traffic, with graphical presentation preferred. The CD&R system was only minimally effective during STBO because the prevailing visibility was sufficient for visual detection of incurring traffic. Overall, the pilots indicated STBO increased general situation awareness but also negatively impacted workload, reduced the ability to watch for other traffic, and increased head-down time.

XAFS study of copper and silver nanoparticles in glazes of medieval middle-east lustreware (10th-13th century)

NASA Astrophysics Data System (ADS)

Padovani, S.; Puzzovio, D.; Sada, C.; Mazzoldi, P.; Borgia, I.; Sgamellotti, A.; Brunetti, B. G.; Cartechini, L.; D'Acapito, F.; Maurizio, C.; Shokoui, F.; Oliaiy, P.; Rahighi, J.; Lamehi-Rachti, M.; Pantos, E.

2006-06-01

It has recently been shown that lustre decoration of medieval and Renaissance pottery consists of silver and copper nanoparticles dispersed in the glassy matrix of the ceramic glaze. Here the findings of an X-ray absorption fine structure (XAFS) study on lustred glazes of shards belonging to 10th and 13rd century pottery from the National Museum of Iran are reported. Absorption spectra in the visible range have been also measured in order to investigate the relations between colour and glaze composition. Gold colour is mainly due to Ag nanoparticles, though Ag+, Cu+ and Cu2+ ions can be also dispersed within the glassy matrix, with different ratios. Red colour is mainly due to Cu nanoparticles, although some Ag nanoparticles, Ag+ and Cu+ ions can be present. The achievement of metallic Cu and the absence of Cu2+ indicate a higher reduction of copper in red lustre. These findings are in substantial agreement with previous results on Italian Renaissance pottery. In spite of the large heterogeneity of cases, the presence of copper and silver ions in the glaze confirms that lustre formation is mediated by a copper- and silver-alkali ion exchange, followed by nucleation and growth of metal nanoparticles.

Surface treatment of dental porcelain: CO2 laser as an alternative to oven glaze.

PubMed

Sgura, Ricardo; Reis, Mariana Cavalcante; Hernandes, Antonio Carlos; de Abreu Fantini, Márcia Carvalho; Andreeta, Marcello Rubens Barsi; Medeiros, Igor Studart

2015-02-01

This work tested continuous CO2 laser as a surface treatment to dental porcelain and compared it to oven glaze (auto-glaze) by means of roughness and color parameters. Three commercial veneering porcelains with different crystalline content were tested: VM7, VM9, and VM13. Porcelain discs (3.5 × 2.0 mm, diameter × height) were sintered and had one side ground by a diamond bur (45 μm) simulating a chairside adjustment in a clinical office. Specimens (n = 7) were divided into the following groups: C--control (no treatment), G--auto-glaze (oven), and L--surface continuous irradiation with CO2 laser (Gem Laser, Coherent; λ = 10.6 μm). Laser was tested in three exposure times (3, 4, or 5 min) and two irradiances (45 and 50 W/cm(2)). Roughness parameters (Ra, Rz, and Rpm/Rz) were measured using a rugosimeter (Surftest 301, Mitutoyo). Color differences (ΔE) between the G and L groups were calculated (VITA Easyshade); ΔE values up to 3.3 were considered as not perceivable. A surface analysis was conducted by stereomicroscopy (Olympus SZ61) and SEM (Stereoscan 440, LEO). Crystalline content of specimens from groups C and L (50 W/cm(2), 5 min) was assessed by X-ray diffraction and then compared. Surface roughness (Ra and Rz) observed for laser-irradiated groups was similar to G for all studied porcelains. Rpm/Rz ratios were near 1.0 for all groups that indicated a sharp ridge profile for all specimens. Only one laser condition studied (50 W/cm(2), 3 min) from VM7 porcelain resulted in color difference (ΔE = 3.5) to G. Specimens irradiated with 50 W/cm(2) for 5 min presented the smoother surface observed by SEM, comparable to G. X-ray diffraction data revealed an increase in leucite crystallite size for VM9 and VM13 porcelains after laser treatment. Regarding roughness, continuous CO2 laser applied on porcelain surface was as effective as conventional oven auto-glaze.

Scanning electron microscope comparative surface evaluation of glazed-lithium disilicate ceramics under different irradiation settings of Nd:YAG and Er:YAG lasers.

PubMed

Viskic, Josko; Jokic, Drazen; Jakovljevic, Suzana; Bergman, Lana; Ortolan, Sladana Milardovic; Mestrovic, Senka; Mehulic, Ketij

2018-01-01

To evaluate the surface of glazed lithium disilicate dental ceramics after irradiation under different irradiation settings of Nd:YAG and Er:YAG lasers using a scanning electron microscope (SEM). Three glazed-press lithium disilicate ceramic discs were treated with HF, Er:YAG, and Nd:YAG, respectively. The laser-setting variables tested were laser mode, repetition rate (Hz), power (W), time of exposure (seconds), and laser energy (mJ). Sixteen different variable settings were tested for each laser type, and all the samples were analyzed by SEM at 500× and 1000× magnification. Surface analysis of the HF-treated sample showed a typical surface texture with a homogenously rough pattern and exposed ceramic crystals. Er:YAG showed no effect on the surface under any irradiation setting. The surface of Nd:YAG-irradiated samples showed cracking, melting, and resolidifying of the ceramic glaze. These changes became more pronounced as the power increased. At the highest power setting (2.25 W), craters on the surface with large areas of melted or resolidified glaze surrounded by globules were visible. However, there was little to no exposure of ceramic crystals or visible regular surface roughening. Neither Er:YAG nor Nd:YAG dental lasers exhibited adequate surface modification for bonding of orthodontic brackets on glazed lithium disilicate ceramics compared with the control treated with 9.5% HF.

Safe Reentry for False Aneurysm Operations in High-Risk Patients.

PubMed

Martinelli, Gian Luca; Cotroneo, Attilio; Caimmi, Philippe Primo; Musica, Gabriele; Barillà, David; Stelian, Edmond; Romano, Angelo; Novelli, Eugenio; Renzi, Luca; Diena, Marco

2017-06-01

In the absence of a standardized safe surgical reentry strategy for high-risk patients with large or anterior postoperative aortic false aneurysm (PAFA), we aimed to describe an effective and safe approach for such patients. We prospectively analyzed patients treated for PAFA between 2006 and 2015. According to the preoperative computed tomography scan examination, patients were divided into two groups according to the anatomy and extension of PAFA: in group A, high-risk PAFA (diameter ≥3 cm) developed in the anterior mediastinum; in group B, low-risk PAFA (diameter <3 cm) was situated posteriorly. For group A, a safe surgical strategy, including continuous cerebral, visceral, and coronary perfusion was adopted before resternotomy; group B patients underwent conventional surgery. We treated 27 patients (safe reentry, n = 13; standard approach, n = 14). Mean age was 60 years (range, 29 to 80); 17 patients were male. Mean interval between the first operation and the last procedure was 4.3 years. Overall 30-day mortality rate was 7.4% (1 patient in each group). No aorta-related mortality was observed at 1 and 5 years in either group. The Kaplan-Meier overall survival estimates at 1 and 5 years were, respectively, 92.3% ± 7.4% and 73.4% ± 13.4% in group A, and 92.9% ± 6.9% and 72.2% ± 13.9% in group B (log rank test, p = 0.830). Freedom from reoperation for recurrent aortic disease was 100% at 1 year and 88% at 5 years. The safe reentry technique with continuous cerebral, visceral, and coronary perfusion for high-risk patients resulted in early and midterm outcomes similar to those observed for low-risk patients undergoing conventional surgery. Copyright © 2017 The Society of Thoracic Surgeons. Published by Elsevier Inc. All rights reserved.

Applications of a synergic analytical strategy to figure out technologies in medieval glazed pottery with "negative decoration" from Italy

NASA Astrophysics Data System (ADS)

Giannossa, Lorena Carla; Acquaviva, Marianna; Laganara, Caterina; Laviano, Rocco; Mangone, Annarosa

2014-09-01

Glazed pottery with "negative decoration" samples, dating back to the twelfth to thirteenth century ad and coming from three sites along the Adriatic coast, Siponto, Egnatia and Trani (Southern Italy) were characterized from physical-chemical, mineralogical and morphological points of view. Optical microscopy, scanning electron microscopy with energy dispersive X-ray spectroscopy, inductively coupled plasma-mass spectroscopy, X-ray diffraction and micro-Raman spectroscopy investigations were carried out on ceramic bodies, pigments and glazes of the fragments. We aimed to outline the technological features, define the nature of decorations and coatings—glazes and engobes—and look for clues to hypothesize provenance. Results obtained show clear differences in raw materials and production technology between the impressed ceramic of Islamic tradition and the incised one of Byzantine tradition. Regarding the latter, evidences of a non-local origin can be found in the compositional diversity of raw materials used for the ceramic bodies of fragments decorated with spiral and pseudo-kufic motifs, which stressed the use of clays so far not recorded in Apulia. At the same time, at least in the case of Siponto, the compositional similarity of both ceramic bodies and materials used under the glaze for impressed ceramic and painted polychrome ceramics (RMR and protomaiolica), more likely local production, could suggest that both were produced in the same workshops.

Microstructure characteristics of vacuum glazing brazing joints using laser sealing technique

NASA Astrophysics Data System (ADS)

Liu, Sixing; Yang, Zheng; Zhang, Jianfeng; Zhang, Shanwen; Miao, Hong; Zhang, Yanjun; Zhang, Qi

2018-05-01

Two pieces of plate glass were brazed into a composite of glazing with a vacuum chamber using PbO-TiO2-SiO2-RxOy powder filler alloys to develop a new type of vacuum glazing. The brazing process was carried out by laser technology. The interface characteristics of laser brazed joints formed between plate glass and solder were investigated using optical microscope, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD) techniques. The results show that the inter-diffusion of Pb/Ti/Si/O elements from the sealing solder toward the glass and O/Al/Si elements from the glass toward the solder, resulting in a reaction layer in the brazed joints. The microstructure phases of PbTiO3, AlSiO, SiO2 and PbO in the glass/solder interface were confirmed by XRD analysis. The joining of the sealing solder to the glass was realized by the reaction products like fibrous structures on interface, where the wetting layer can help improve the bonding performance and strength between the sealing solder and the plate glass during the laser brazing process.

Unmanned Aerial Systems Traffic Management (UTM): Safely Enabling UAS Operations in Low-Altitude Airspace

NASA Technical Reports Server (NTRS)

Rios, Joseph

2016-01-01

Currently, there is no established infrastructure to enable and safely manage the widespread use of low-altitude airspace and UAS flight operations. Given this, and understanding that the FAA faces a mandate to modernize the present air traffic management system through computer automation and significantly reduce the number of air traffic controllers by FY 2020, the FAA maintains that a comprehensive, yet fully automated UAS traffic management (UTM) system for low-altitude airspace is needed. The concept of UTM is to begin by leveraging concepts from the system of roads, lanes, stop signs, rules and lights that govern vehicles on the ground today. Building on its legacy of work in air traffic management (ATM), NASA is working with industry to develop prototype technologies for a UAS Traffic Management (UTM) system that would evolve airspace integration procedures for enabling safe, efficient low-altitude flight operations that autonomously manage UAS operating in an approved low-altitude airspace environment. UTM is a cloud-based system that will autonomously manage all traffic at low altitudes to include UASs being operated beyond visual line of sight of an operator. UTM would thus enable safe and efficient flight operations by providing fully integrated traffic management services such as airspace design, corridors, dynamic geofencing, severe weather and wind avoidance, congestion management, terrain avoidance, route planning re-routing, separation management, sequencing spacing, and contingency management. UTM removes the need for human operators to continuously monitor aircraft operating in approved areas. NASA envisions concepts for two types of UTM systems. The first would be a small portable system, which could be moved between geographical areas in support of operations such as precision agriculture and public safety. The second would be a Persistent system, which would support low-altitude operations in an approved area by providing continuous automated

Critical issues in assuring long lifetime and fail-safe operation of optical communications network

NASA Astrophysics Data System (ADS)

Paul, Dilip K.

1993-09-01

Major factors in assuring long lifetime and fail-safe operation in optical communications networks are reviewed in this paper. Reliable functionality to design specifications, complexity of implementation, and cost are the most critical issues. As economics is the driving force to set the goals as well as priorities for the design, development, safe operation, and maintenance schedules of reliable networks, a balance is sought between the degree of reliability enhancement, cost, and acceptable outage of services. Protecting both the link and the network with high reliability components, hardware duplication, and diversity routing can ensure the best network availability. Case examples include both fiber optic and lasercom systems. Also, the state-of-the-art reliability of photonics in space environment is presented.

Method and apparatus for an insulating glazing unit and compliant seal for an insulating glazing unit

DOEpatents

Francis, IV, William H.; Freebury, Gregg E.; Beidleman, Neal J.; Hulse, Michael

2016-05-03

A Vacuum Insulating Glazing Unit (VIGU) comprises two or more glass lites (panes) spaced apart from one another and hermetically bonded to an edge seal assembly therebetween. The resulting cavity between the lites is evacuated to create at least one insulating vacuum cavity within which are disposed a plurality of stand-off members to maintain separation between the lites. The edge seal assembly is preferably compliant in the longitudinal (i.e., edgewise) direction to allow longitudinal relative motion between the two lites (e.g., from thermal expansion). The longitudinal compliance may be obtained by imprinting a three-dimensional pattern into the edge seal material. The edge seal assembly is preferably bonded to the lites with a first bond portion that is hermetic and a second bond portion that is load-resistant. Methods for producing VIGUs and/or compliant edge seal assemblies and VIGU and edge seal apparatus are disclosed.

Commercialization Plan Support for Development of Low Cost Vacuum Insulating Glazing: Cooperative Research and Development Final Report, CRADA Number CRD-11-449

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dameron, Arrelaine

During the duration of this CRADA, V-Glass and NREL will partner in testing, analysis, performance forecasting, costing, and evaluation of V-Glass’s GRIPWELD™ process technology for creating a low cost hermetic seal for conventional and vacuum glazing. Upon successful evaluation of hermeticity, V-Glass’s GRIPWELD™ will be evaluated for its potential use in highly insulating window glazing.

Seasonal control skylight glazing panel with passive solar energy switching

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, J.V.

1983-10-25

A substantially transparent one-piece glazing panel is provided for generally horizontal mounting in a skylight. The panel is comprised of an repeated pattern of two alternating and contiguous linear optical elements; a first optical element being an upstanding generally right-triangular linear prism, and the second optical element being an upward-facing plano-cylindrical lens in which the planar surface is reflectively opaque and is generally in the same plane as the base of the triangular prism.

Exploring the safe and just operating space in an inhomogeneous world

NASA Astrophysics Data System (ADS)

Barfuss, Wolfram; Beronov, Boyan; Wiedermann, Marc; Donges, Jonathan

2015-04-01

The Anthropocene has become reality during the 20th century, implying that our species is pressuring the Earth's ecosystems on a global scale. In the meantime, the challenge of eradicating poverty has not yet ceased to exist. Effectively dealing with these issues requires us to better understand the driving forces, feedback loops and tipping elements in the whole Earth system, constituted by natural and social components. To take a step forward in this direction, we refine an existing conceptual coevolutionary model of social and ecological domains (COPAN:EXPLOIT) by introducing inhomogeneities in the properties of local renewable resource stocks that are abstracted from real-world data. We then propose an analytical framework, 'the safe and just space'- plot, which aligns with the current debate on how to simultaneously stay within planetary boundaries (Rockström et al., 2009) and at the same time ensure that social foundations are met (Raworth, 2012). This plot presents a practical tool for jointly studying global socio-ecological models as well as real-world observations. First results from comparing the model outputs with real-world data indicate that the current state of the world is neither particularly safe nor particularly just. References: Rockström, Johan, et al. "A safe operating space for humanity." Nature 461.7263 (2009): 472-475. Raworth, Kate. "A safe and just space for humanity: can we live within the doughnut?" Oxfam Discussion Papers (2012): 1-26.

STS-38 Atlantis, OV-104, during safing operations after KSC SLF landing

NASA Image and Video Library

1990-11-20

Spotlights illuminate Atlantis, Orbiter Vehicle (OV) 104, during safing operations at the Kennedy Space Center's (KSC's) Shuttle Landing Facility (SLF). OV-104 parked on runway 33 is serviced by KSC ground crews. STS-38, a Department of Defense (DOD)-devoted mission, came to an end (with complete wheel stop) at 4:43:37 pm (Eastern Standard Time (EST)).

Use of lead-glazed ceramic ware and lead-based folk remedies in a rural community of Baja California, Mexico.

PubMed

Welton, Michael; Rodriguez-Lainz, Alfonso; Loza, Oralia; Brodine, Stephanie; Fraga, Miguel

2018-03-01

Lead exposure from lead-glazed ceramics (LGCs) and traditional folk remedies have been identified as significant sources of elevated blood lead levels in Mexico and the United States. This study took place from 2005 to 2012 in a rural community in Baja California, Mexico. 1) Investigate the knowledge, attitudes, and practices related to lead and lead exposures from LGCs and two lead-based folk remedies ( azarcon and greta); and 2) evaluate a pilot intervention to provide alternative lead-safe cookware. A baseline household survey was conducted in 2005, followed by the pilot intervention in 2006, and follow-up surveys in 2007 and 2012. For the pilot intervention, families who reported using LGCs were given lead-safe alternative cookware to try and its acceptance was evaluated in the following year. The community was mostly of indigenous background from Oaxaca and a high proportion of households had young children. In 2006, all participants using traditional ceramic ware at the time ( n = 48) accepted lead-safe alternative cookware to try, and 97% reported that they were willing to exchange traditional ceramic ware for lead-safe alternatives. The use of ceramic cookware decreased from over 90% during respondents' childhood household use in Oaxaca to 47% in 2006 among households in Baja California, and further reduced to 16.8% in 2012. While empacho, a folk illness, was widely recognized as an intestinal disorder, there was almost universal unfamiliarity with the use and knowledge of azarcon and greta for its treatment. This pilot evaluation provides evidence 1) for an effective and innovative strategy to reduce lead exposure from LGCs and 2) of the feasibility of substituting lead-free alternative cookware for traditional ceramic ware in a rural indigenous community, when delivered in a culturally appropriate manner with health education. This strategy could complement other approaches to reduce exposure to lead from LGCs.

Unmanned Aircraft Systems Traffic Management (UTM) Safely Enabling UAS Operations in Low-Altitude Airspace

NASA Technical Reports Server (NTRS)

Kopardekar, Parimal H.

2016-01-01

Unmanned Aircraft System (UAS) Traffic Management (UTM) Enabling Civilian Low-Altitude Airspace and Unmanned Aircraft System Operations What is the problem? Many beneficial civilian applications of UAS have been proposed, from goods delivery and infrastructure surveillance, to search and rescue, and agricultural monitoring. Currently, there is no established infrastructure to enable and safely manage the widespread use of low-altitude airspace and UAS operations, regardless of the type of UAS. A UAS traffic management (UTM) system for low-altitude airspace may be needed, perhaps leveraging concepts from the system of roads, lanes, stop signs, rules and lights that govern vehicles on the ground today, whether the vehicles are driven by humans or are automated. What system technologies is NASA exploring? Building on its legacy of work in air traffic management for crewed aircraft, NASA is researching prototype technologies for a UAS Traffic Management (UTM) system that could develop airspace integration requirements for enabling safe, efficient low-altitude operations. While incorporating lessons learned from the today's well-established air traffic management system, which was a response that grew out of a mid-air collision over the Grand Canyon in the early days of commercial aviation, the UTM system would enable safe and efficient low-altitude airspace operations by providing services such as airspace design, corridors, dynamic geofencing, severe weather and wind avoidance, congestion management, terrain avoidance, route planning and re-routing, separation management, sequencing and spacing, and contingency management. One of the attributes of the UTM system is that it would not require human operators to monitor every vehicle continuously. The system could provide to human managers the data to make strategic decisions related to initiation, continuation, and termination of airspace operations. This approach would ensure that only authenticated UAS could operate

Tensile bond strength of metal bracket bonding to glazed ceramic surfaces with different surface conditionings.

PubMed

Akhoundi, Ms Ahmad; Kamel, M Rahmati; Hashemi, Sh Mahmood; Imani, M

2011-01-01

The objective of this study was to compare the tensile bond strength of metal brackets bonding to glazed ceramic surfaces using three various surface treatments. Forty two glazed ceramic disks were assigned to three groups. In the first and second groups the specimens were etched with 9.5% hydrofluoric acid (HFA). Subsequently in first group, ceramic primer and adhesive were applied, but in second group a bonding agent alone was used. In third group, specimens were treated with 35% phosphoric acid followed by ceramic primer and adhesive application. Brackets were bonded with light cure composites. The specimens were stored in distilled water in the room temperature for 24 hours and thermocycled 500 times between 5°C and 55°C. The universal testing machine was used to test the tensile bond strength and the adhesive remenant index scores between three groups was evaluated. The data were subjected to one-way ANOVA, Tukey and Kruskal-Wallis tests respectively. The tensile bond strength was 3.69±0.52 MPa forfirst group, 2.69±0.91 MPa for second group and 3.60±0.41 MPa for third group. Group II specimens showed tensile strength values significantly different from other groups (P<0.01). In spite of limitations in laboratory studies it may be concluded that in application of Scotch bond multipurpose plus adhesive, phosphoric acid can be used instead of HFA for bonding brackets to the glazed ceramic restorations with enough tensile bond strength.

Recommendations For The Safe Design, Operation And Use Of Commercial Sun Tanning Equipment

NASA Astrophysics Data System (ADS)

Cox, E. A.

1982-02-01

HSE Guidance Notes are being prepared to give recommendations to the designers, manufacturers, operators and users of commercial sun tanning equipment on the various health and safety aspects associated with the safe construction, siting and use of such equipment. Medically prescribed ultraviolet treatments are excluded from the guidance.

Parametric Experimental Study of the Formation of Glaze Ice Shapes on Swept Wings

NASA Technical Reports Server (NTRS)

Vargas, Mario; Reshotko, Eli

1999-01-01

An experiment was conducted to study the effect of velocity and sweep angle on the critical distance in ice accretion formation on swept wings at glaze ice conditions. The critical distance is defined as the distance from the attachment line to the beginning of the zone where roughness elements develop into glaze ice feathers. Icing runs were performed on a NACA 00 1 2 swept wing tip at velocities of 75, 100, 150, and 200 miles per hour. At each velocity and tunnel condition, the sweep angle was changed from 0 deg to 45 deg at 5 deg increments. Casting data, ice shape tracings, and close-up photographic data were obtained. The results showed that at given velocity and tunnel conditions, as the sweep angle is increased from 0 deg to 25 deg the critical distance slowly decreases. As the sweep angle is increased past 25 deg, the critical distance starts decreasing more rapidly. For 75 and 100 mph it reaches a value of 0 millimeters at 35 deg. For 150 and 200 mph it reaches a value of 0 millimeters at 40 deg. On the ice accretion, as the sweep angle is increased from 0 deg to 25 deg, the extent of the attachment line zone slowly decreases. In the glaze ice feathers zone, the angle that the preferred direction of growth of the feathers makes with respect to the attachment line direction increases. But overall, the ice accretions remain similar to the 0 deg sweep angle case. As the sweep angle is increased above 25 deg, the extent of the attachment line zone decreases rapidly and complete scallops form at 35 deg sweep angle for 75 and 100 mph, and at 40 deg for 150 and 200 mph.

Extended Aging Theories for Predictions of Safe Operational Life of Critical Airborne Structural Components

NASA Technical Reports Server (NTRS)

Ko, William L.; Chen, Tony

2006-01-01

The previously developed Ko closed-form aging theory has been reformulated into a more compact mathematical form for easier application. A new equivalent loading theory and empirical loading theories have also been developed and incorporated into the revised Ko aging theory for the prediction of a safe operational life of airborne failure-critical structural components. The new set of aging and loading theories were applied to predict the safe number of flights for the B-52B aircraft to carry a launch vehicle, the structural life of critical components consumed by load excursion to proof load value, and the ground-sitting life of B-52B pylon failure-critical structural components. A special life prediction method was developed for the preflight predictions of operational life of failure-critical structural components of the B-52H pylon system, for which no flight data are available.

49 CFR 393.61 - Truck and truck tractor window construction.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 5 2010-10-01 2010-10-01 false Truck and truck tractor window construction. 393... REGULATIONS PARTS AND ACCESSORIES NECESSARY FOR SAFE OPERATION Glazing and Window Construction § 393.61 Truck and truck tractor window construction. Each truck and truck tractor (except trucks engaged in armored...

Non-destructive identification of green and yellow pigments: the case of some Sicilian Renaissance glazed pottery

NASA Astrophysics Data System (ADS)

Crupi, V.; Majolino, D.; Venuti, V.; Barone, G.; Mazzoleni, P.; Pezzino, A.; La Russa, M. F.; Ruffolo, S. A.; Bardelli, F.

2010-09-01

Selected decorated Renaissance ceramic fragments, found during the excavation of a Sicilian archaeological site (Caltagirone, Sicily, South Italy), have been studied by combining scanning electron microscopy (SEM), energy-dispersive X-ray spectrometry (EDS), and X-ray absorbance spectroscopy (XAS). The study was aimed at providing microchemical and microstructural characterization of the colored glazed coatings in order to elucidate the nature of the pigments in the decorative layers, and in the glaze itself. From the obtained results, the general perspective has been the identification of information to be used for a reliable recognition of the production techniques. In particular, XAS measurements, performed using synchrotron radiation (SR) as the source at the Cu K-edge, in the case of green decorations, provided structural information of the oxidation states and the local chemical environment of copper (neighboring atoms and bond distances).

Practical significance and calculation of surface tension of glass, enamels and glazes

NASA Technical Reports Server (NTRS)

Dietzel, A.

1987-01-01

Surface tension is important in the formation of streaks in the whole procedure of enameling and glazing., in the action of TiO2 as opacifier, in the addition of borax to enamels, or metals to glasses, and in the corrosion of refractories by molten charges. By the use of known methods for measuring surface tension additive constants are found which give correct results within 1% with no discrepancy due to B2O3.

Guidance regarding voluntary compliance with international management code for the safe operation of ships and for pollution prevention

DOT National Transportation Integrated Search

1994-03-15

The purpose of this Circular is to advise owners and operators of U.S. flag merchant vessels regarding voluntary compliance with the International Management Code for the Safe Operation of Ships and for Pollution Prevention.

Safely Enabling Civilian Unmanned Aerial System (UAS) Operations In Low-Altitude Airspace By Unmanned Aerial System Traffic Management (UTM)

NASA Technical Reports Server (NTRS)

Kopardekar, Parimal H.

2015-01-01

Many UAS will operate at lower altitude (Class G, below 2000 feet)There is urgent need for a system for civilian low-altitude airspace and UAS operations. Stakeholders want to work with NASA to enable safe operations.

77 FR 52625 - Petition Requesting Rulemaking To Revise Test Procedures for Glazing Materials in Architectural...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-30

... contains notices to the public of #0;the proposed issuance of rules and regulations. The purpose of these... architectural products set forth in our regulations, with those testing procedures contained in ANSI Z97.1, ``American National Standard for Safety Glazing Materials Used in Building--Safety Performance Specifications...

76 FR 9853 - Parts and Accessories Necessary for Safe Operation; Brakes; Application for Exemption From...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-22

... Innovative Electronics; Correction AGENCY: Federal Motor Carrier Safety Administration (FMCSA), DOT. ACTION... Accessories Necessary for Safe Operation; Brakes; Application for Exemption From Innovative Electronics... Innovative Electronics; Notice of application for exemption; request for comments (76 FR 7623, February 10...

Safely Enabling Civilian Unmanned Aerial System (UAS) Operations in Low-Altitude Airspace by Unmanned Aerial System Traffic Management (UTM)

NASA Technical Reports Server (NTRS)

Kopardekar, Parimal Hemchandra

2015-01-01

Many UAS will operate at lower altitude (Class G, below 2000 feet). There is an urgent need for a system for civilian low-altitude airspace and UAS operations. Stakeholders want to work with NASA to enable safe operations.

[Influence of different designs and porcelain/glaze firing on the marginal and internal fit of implant-supported zirconia crowns].

PubMed

Cuiling, Liu; Xu, Gao; Yuping, Qi; Liyuan, Yang

2016-02-01

This study investigated the influence of different designs and porcelain/glaze firing on the marginal and internal fit of three kinds of computer aided design/computer aided manufacturing (CAD/CAM) zirconia ceramic implant-supported crowns. Three groups of zirconia ceramic implant-supported crowns with different designs were produced from copings by using a Cercon CAD/CAM system (n = 8). The first two groups comprised double-layer crowns (zirconia coping + veneer) with regular (Group A) and full circumferential zirconia-collar marginal designs (Group B). The third group was composed of anatomic single-layer zirconia crowns without cores (Group C). Initially, the marginal and internal gaps of the copings and crowns were individually replicated by light-body silicon and then measured by micro-computed tomography scanning before and after porcelain/glaze firing. Five measurements were employed: vertical marginal gap (MG); horizontal marginal discrepancy (HMD); chamfer area (CA); axial wall (AW); and axial-occlusal transition area (AOT). Statistical analyses were performed by SPSS 17.0. HMD measurements in Group A were statistically higher than those in Groups B and C (P < 0.05), regardless of whether the values were obtained before or after porcelain/glaze firing. By contrast, the HIMD measurements in Groups B and C showed no significant difference (P > 0.05). Moreover, no differences were noted in MG, CA, AW, and AOT among the three groups (P > 0.05). All the measurements in the three groups showed no significant change after porcelain/glaze firing (P > 0.05), except for MG in Group A, which significantly decreased (P < 0.05). The marginal fits of the double-layer crowns with full circumferential zirconia-collar and the anatomic single-layer zirconia crowns were superior to that of the double-layer crowns with regular margins. The MG of the crowns with regular margins was obviously influenced by porcelain firing.

Additional Results of Glaze Icing Scaling in SLD Conditions

NASA Technical Reports Server (NTRS)

Tsao, Jen-Ching

2016-01-01

New guidance of acceptable means of compliance with the super-cooled large drops (SLD) conditions has been issued by the U.S. Department of Transportation's Federal Aviation Administration (FAA) in its Advisory Circular AC 25-28 in November 2014. The Part 25, Appendix O is developed to define a representative icing environment for super-cooled large drops. Super-cooled large drops, which include freezing drizzle and freezing rain conditions, are not included in Appendix C. This paper reports results from recent glaze icing scaling tests conducted in NASA Glenn Icing Research Tunnel (IRT) to evaluate how well the scaling methods recommended for Appendix C conditions might apply to SLD conditions. The models were straight NACA 0012 wing sections. The reference model had a chord of 72 inches and the scale model had a chord of 21 inches. Reference tests were run with airspeeds of 100 and 130.3 knots and with MVD's of 85 and 170 microns. Two scaling methods were considered. One was based on the modified Ruff method with scale velocity found by matching the Weber number W (sub eL). The other was proposed and developed by Feo specifically for strong glaze icing conditions, in which the scale liquid water content and velocity were found by matching reference and scale values of the non-dimensional water-film thickness expression and the film Weber number W (sub ef). All tests were conducted at 0 degrees angle of arrival. Results will be presented for stagnation freezing fractions of 0.2 and 0.3. For non-dimensional reference and scale ice shape comparison, a new post-scanning ice shape digitization procedure was developed for extracting 2-dimensional ice shape profiles at any selected span-wise location from the high fidelity 3-dimensional scanned ice shapes obtained in the IRT.

Additional Results of Glaze Icing Scaling in SLD Conditions

NASA Technical Reports Server (NTRS)

Tsao, Jen-Ching

2016-01-01

New guidance of acceptable means of compliance with the super-cooled large drops (SLD) conditions has been issued by the U.S. Department of Transportation's Federal Aviation Administration (FAA) in its Advisory Circular AC 25-28 in November 2014. The Part 25, Appendix O is developed to define a representative icing environment for super-cooled large drops. Super-cooled large drops, which include freezing drizzle and freezing rain conditions, are not included in Appendix C. This paper reports results from recent glaze icing scaling tests conducted in NASA Glenn Icing Research Tunnel (IRT) to evaluate how well the scaling methods recommended for Appendix C conditions might apply to SLD conditions. The models were straight NACA 0012 wing sections. The reference model had a chord of 72 in. and the scale model had a chord of 21 in. Reference tests were run with airspeeds of 100 and 130.3 kn and with MVD's of 85 and 170 micron. Two scaling methods were considered. One was based on the modified Ruff method with scale velocity found by matching the Weber number WeL. The other was proposed and developed by Feo specifically for strong glaze icing conditions, in which the scale liquid water content and velocity were found by matching reference and scale values of the nondimensional water-film thickness expression and the film Weber number Wef. All tests were conducted at 0 deg AOA. Results will be presented for stagnation freezing fractions of 0.2 and 0.3. For nondimensional reference and scale ice shape comparison, a new post-scanning ice shape digitization procedure was developed for extracting 2-D ice shape profiles at any selected span-wise location from the high fidelity 3-D scanned ice shapes obtained in the IRT.

The effect of repeated firings on the color change of dental ceramics using different glazing methods

PubMed Central

Yılmaz, Kerem; Ozturk, Caner

2014-01-01

PURPOSE Surface color is one of the main criteria to obtain an ideal esthetic. Many factors such as the type of the material, surface specifications, number of firings, firing temperature and thickness of the porcelain are all important to provide an unchanged surface color in dental ceramics. The aim of this study was to evaluate the color changes in dental ceramics according to the material type and glazing methods, during the multiple firings. MATERIALS AND METHODS Three different types of dental ceramics (IPS Classical metal ceramic, Empress Esthetic and Empress 2 ceramics) were used in the study. Porcelains were evaluated under five main groups according to glaze and natural glaze methods. Color changes (ΔE) and changes in color parameters (ΔL, Δa, Δb) were determined using colorimeter during the control, the first, third, fifth, and seventh firings. The statistical analysis of the results was performed using ANOVA and Tukey test. RESULTS The color changes which occurred upon material-method-firing interaction were statistically significant (P<.05). ΔE, ΔL, Δa and Δb values also demonstrated a negative trend. The MC-G group was less affected in terms of color changes compared to other groups. In all-ceramic specimens, the surface color was significantly affected by multiple firings. CONCLUSION Firing detrimentally affected the structure of the porcelain surface and hence caused fading of the color and prominence of yellow and red characters. Compressible all-ceramics were remarkably affected by repeated firings due to their crystalline structure. PMID:25551001

Who's Got the Bridge? - Towards Safe, Robust Autonomous Operations at NASA Langley's Autonomy Incubator

NASA Technical Reports Server (NTRS)

Allen, B. Danette; Cross, Charles D.; Motter, Mark A.; Neilan, James H.; Qualls, Garry D.; Rothhaar, Paul M.; Tran, Loc; Trujillo, Anna C.; Crisp, Vicki K.

2015-01-01

NASA aeronautics research has made decades of contributions to aviation. Both aircraft and air traffic management (ATM) systems in use today contain NASA-developed and NASA sponsored technologies that improve safety and efficiency. Recent innovations in robotics and autonomy for automobiles and unmanned systems point to a future with increased personal mobility and access to transportation, including aviation. Automation and autonomous operations will transform the way we move people and goods. Achieving this mobility will require safe, robust, reliable operations for both the vehicle and the airspace and challenges to this inevitable future are being addressed now in government labs, universities, and industry. These challenges are the focus of NASA Langley Research Center's Autonomy Incubator whose R&D portfolio includes mission planning, trajectory and path planning, object detection and avoidance, object classification, sensor fusion, controls, machine learning, computer vision, human-machine teaming, geo-containment, open architecture design and development, as well as the test and evaluation environment that will be critical to prove system reliability and support certification. Safe autonomous operations will be enabled via onboard sensing and perception systems in both data-rich and data-deprived environments. Applied autonomy will enable safety, efficiency and unprecedented mobility as people and goods take to the skies tomorrow just as we do on the road today.

Imaging Flash Lidar for Autonomous Safe Landing and Spacecraft Proximity Operation

NASA Technical Reports Server (NTRS)

Amzajerdian, Farzin; Roback, Vincent E.; Brewster, Paul F.; Hines, Glenn D.; Bulyshev, Alexander E.

2016-01-01

3-D Imaging flash lidar is recognized as a primary candidate sensor for safe precision landing on solar system bodies (Moon, Mars, Jupiter and Saturn moons, etc.), and autonomous rendezvous proximity operations and docking/capture necessary for asteroid sample return and redirect missions, spacecraft docking, satellite servicing, and space debris removal. During the final stages of landing, from about 1 km to 500 m above the ground, the flash lidar can generate 3-Dimensional images of the terrain to identify hazardous features such as craters, rocks, and steep slopes. The onboard fli1ght computer can then use the 3-D map of terrain to guide the vehicle to a safe location. As an automated rendezvous and docking sensor, the flash lidar can provide relative range, velocity, and bearing from an approaching spacecraft to another spacecraft or a space station from several kilometers distance. NASA Langley Research Center has developed and demonstrated a flash lidar sensor system capable of generating 16k pixels range images with 7 cm precision, at a 20 Hz frame rate, from a maximum slant range of 1800 m from the target area. This paper describes the lidar instrument design and capabilities as demonstrated by the closed-loop flight tests onboard a rocket-propelled free-flyer vehicle (Morpheus). Then a plan for continued advancement of the flash lidar technology will be explained. This proposed plan is aimed at the development of a common sensor that with a modest design adjustment can meet the needs of both landing and proximity operation and docking applications.

Finite wing aerodynamics with simulated glaze ice

NASA Technical Reports Server (NTRS)

Khodadoust, A.; Bragg, M. B.; Kerho, M.; Wells, S.; Soltani, M. R.

1992-01-01

The effect of a simulated glaze ice accretion on the aerodynamic performance of a three-dimensional wing is studied experimentally. The model used for these tests was a semi-span wing of effective aspect ratio five, mounted from the sidewall of the UIUC subsonic wind tunnel. The model has an NACA 0012 airfoil section on a rectangular, untwisted planform with interchangeable leading edges to allow for testing both the baseline and the iced wing geometry. A three-component sidewall balance was used to measure lift, drag and pitching moment on the clean and iced model. A four-beam two-color fiberoptic laser Doppler velocimeter (LDV) was used to map the flowfield along several spanwise cuts on the model. Preliminary results from LDV scans, which will be the bulk of this paper, are presented following the force balance measurement results. Initial comparison of LDV surveys compare favorably with inviscid theory results and 2D split hot-film measurements near the model surface.

Strategies for Countering Terrorist Safe Havens

DTIC Science & Technology

2014-02-20

within safe havens, tactical containment, pseudo operations, and surrogate security forces. The thesis draws from four historical case studies to...leadership targeting within safe havens, tactical containment, pseudo operations, and surrogate security forces. The thesis draws from four historical case ...surrogate forces and pseudo operations—provide viable potential options for USSOF to counter the complex problem of safe havens. Overall, the case

What influences youth to operate all-terrain vehicles safely?

PubMed Central

Grummon, A. H.; Heaney, C. A.; Dellinger, W. A.; Wilkins, J. R.

2014-01-01

The operation of all-terrain vehicles (ATVs) by youth has contributed to the incidence of serious and fatal injuries among children. This study explored factors related to the frequency with which youth wore a helmet and refrained from engaging in three risky driving behaviors (driving at risky speeds, on paved roads and on unfamiliar terrain) while operating an ATV. Youth (n = 248) aged 9–14 from central Ohio and one of their parents completed self-report measures of ATV safety behaviors, youth general propensity for risk taking, protection motivation and parental behaviors to facilitate youth safety. Data from two focus groups provided insight on quantitative results. Analyses revealed considerable variation in the frequency with which youth performed the safety behaviors, with 13- and 14-year-olds reporting less frequent safe behavior than 9- to 12-year-olds. Multiple regression analyses suggested that parental behaviors, such as providing reminders to wear a helmet, were associated with more frequent helmet use but were not associated with risky driving behaviors. Youth’s general propensity toward risk taking was not associated with helmet use and only associated with riskydriving behaviors among the 13- and 14-year-olds. Self-efficacy was an important predictor across both age groups and behaviors. Implications for injury prevention are discussed. PMID:24740837

An experimental study of the aerodynamics of a NACA 0012 airfoil with a simulated glaze ice accretion

NASA Technical Reports Server (NTRS)

Bragg, M. B.

1986-01-01

An experimental study was conducted in the Ohio State University subsonic wind tunnel to measure the detailed aerodynamic characteristics of an airfoil with a simulated glaze ice accretion. A NACA 0012 model with interchangeable leading edges and pressure taps every one percent chord was used. Surface pressure and wake data were taken on the airfoil clean, with forced transition and with a simulated glaze ice shape. Lift and drag penalties due to the ice shape were found and the surface pressure clearly showed that large separation bubbles were present. Both total pressure and split-film probes were used to measure velocity profiles, both for the clean model and for the model with a simulated ice accretion. A large region of flow separation was seen in the velocity profiles and was correlated to the pressure measurements. Clean airfoil data were found to compare well to existing airfoil analysis methods.

Conducting Safe and Efficient Airport Surface Operations in a NextGen Environment

NASA Technical Reports Server (NTRS)

Jones, Denise R.; Prinzel, Lawrence J., III; Bailey, Randall E.; Arthur, Jarvis J., III; Barnes, James R.

2016-01-01

The Next Generation Air Transportation System (NextGen) vision proposes many revolutionary operational concepts, such as surface trajectory-based operations (STBO) and technologies, including display of traffic information and movements, airport moving maps (AMM), and proactive alerts of runway incursions and surface traffic conflicts, to deliver an overall increase in system capacity and safety. A piloted simulation study was conducted at the National Aeronautics and Space Administration (NASA) Langley Research Center to evaluate the ability of a flight crew to conduct safe and efficient airport surface operations while utilizing an AMM. Position accuracy of traffic was varied, and the effect of traffic position accuracy on airport conflict detection and resolution (CD&R) capability was measured. Another goal was to evaluate the crew's ability to safely conduct STBO by assessing the impact of providing traffic intent information, CD&R system capability, and the display of STBO guidance to the flight crew on both head-down and head-up displays (HUD). Nominal scenarios and off-nominal conflict scenarios were conducted using 12 airline crews operating in a simulated Memphis International Airport terminal environment. The data suggest that all traffic should be shown on the airport moving map, whether qualified or unqualified, and conflict detection and resolution technologies provide significant safety benefits. Despite the presence of traffic information on the map, collisions or near-collisions still occurred; when indications or alerts were generated in these same scenarios, the incidents were averted. During the STBO testing, the flight crews met their required time-of-arrival at route end within 10 seconds on 98 percent of the trials, well within the acceptable performance bounds of 15 seconds. Traffic intent information was found to be useful in determining the intent of conflicting traffic, with graphical presentation preferred. The CD&R system was only

Estimation of safe exposure time from an ophthalmic operating microscope with regard to ultraviolet radiation and blue-light hazards to the eye

NASA Astrophysics Data System (ADS)

Michael, Ralph; Wegener, Alfred

2004-08-01

Hazards from the optical radiation of an operating microscope that cause damage at the corneal, lenticular, and retinal levels were investigated; we considered, in particular, ultraviolet radiation (UVR) and blue light. The spectral irradiance from a Zeiss operation microscope OPMI VISU 200 was measured in the corneal plane between 300 and 1100 nm. Effective irradiance and radiance were calculated with relative spectral effectiveness data from the American Conference for Governmental and Industrial Hygienists. Safe exposure time to avoid UVR injury to the lens and cornea was found to be 2 h without a filter, 4 h with a UVR filter, 200 h with a yellow filter, and 400 h with a filter combination. Safe exposure time to avoid retinal photochemical injury was found to be 3 min without a filter and with a UVR filter, 10 min with a yellow filter, and 49 min with a filter combination. The effective radiance limit for retinal thermal injury was not exceeded. The hazard due to the UVR component from the operating microscope is not critical, and operation time can be safely prolonged with the use of appropriate filters. The retinal photochemical hazard appears critical without appropriate filters, permitting only some minutes of safe exposure time. The calculated safe exposure times are for worst-case conditions and maximal light output and include a safety factor.

Estimation of safe exposure time from an ophthalmic operating microscope with regard to ultraviolet radiation and blue-light hazards to the eye.

PubMed

Michael, Ralph; Wegener, Alfred

2004-08-01

Hazards from the optical radiation of an operating microscope that cause damage at the corneal, lenticular, and retinal levels were investigated; we considered, in particular, ultraviolet radiation (UVR) and blue light. The spectral irradiance from a Zeiss operation microscope OPMI VISU 200 was measured in the corneal plane between 300 and 1100 nm. Effective irradiance and radiance were calculated with relative spectral effectiveness data from the American Conference for Governmental and Industrial Hygienists. Safe exposure time to avoid UVR injury to the lens and cornea was found to be 2 h without a filter, 4 h with a UVR filter, 200 a yellow filter, and 400 h with a filter combination. Safe exposure time to avoid retinal photochemical injury was found to be 3 min without a filter and with a UVR filter, 10 min with a yellow filter, and 49 min with a filter combination. The effective radiance limit for retinal thermal injury was not exceeded. The hazard due to the UVR component from the operating microscope is not critical, and operation time can be safely prolonged with the use of appropriate filters. The retinal photochemical hazard appears critical without appropriate filters, permitting only some minutes of safe exposure time. The calculated safe exposure times are for worst-case conditions and maximal light output and include a safety factor.

Effect of Traffic Position Accuracy for Conducting Safe Airport Surface Operations

NASA Technical Reports Server (NTRS)

Jones, Denise R.; Prinzel, Lawrence J., III; Bailey, Randall E.; Arthur, Jarvis J., III; Barnes, James R.

2014-01-01

The Next Generation Air Transportation System (NextGen) concept proposes many revolutionary operational concepts and technologies, such as display of traffic information and movements, airport moving maps (AMM), and proactive alerts of runway incursions and surface traffic conflicts, to deliver an overall increase in system capacity and safety. A piloted simulation study was conducted at the National Aeronautics and Space Administration (NASA) Langley Research Center to evaluate the ability to conduct safe and efficient airport surface operations while utilizing an AMM displaying traffic of various position accuracies as well as the effect of traffic position accuracy on airport conflict detection and resolution (CD&R) capability. Nominal scenarios and off-nominal conflict scenarios were conducted using 12 airline crews operating in a simulated Memphis International Airport terminal environment. The data suggest that all traffic should be shown on the airport moving map, whether qualified or unqualified, and conflict detection and resolution technologies provide significant safety benefits. Despite the presence of traffic information on the map, collisions or near collisions still occurred; when indications or alerts were generated in these same scenarios, the incidences were averted.

Eye Safe, Visible Wavelength Lidar Systems: Design and Operational Advances, Results and Potential

NASA Technical Reports Server (NTRS)

Spinhirne, James; Welton, Ellsworth J.; Berkoff, Timothy; Campbell, James

2007-01-01

In the early nineties the first of the eye safe visible wavelength lidar systems known now as Micro Pulse Lidar (MPL) became operational. The important advance of the design was a system that, unlike most existing lidar, operated at eye safe energy densities and could thus operate unattended for full time monitoring. Since that time there have been many dozens of these systems produced and applied for full time profiling of atmospheric cloud and aerosol structure. There is currently an observational network of MPL sites to support global climate research. In thc course of application of these instruments there have been significant improvements in the, design and performance of the systems. In the last half decade particularly there has been significant application and technical development of MPL systems. In this paper we review progress. The current MPL systems in use are all single wavelength systems designed for cloud and aerosol applications. For the cloud and aerosol applications, both lidar depolarization and multi wavelength measurements have significant applications. These can be accomplished with the MPL, approach. The main current challenge for the lidar network activity are in the area of the reliability, repeatability and efficiency of data processing. The network makes use of internet data downloads and automated processing. The heights of all cloud and aerosol layers are needed. The recent emphasis has been in operationally deriving aerosol extinction cross section. Future emphasis will include adding cirrus optical parameters. For operational effectiveness, improvements to simplify routine data signal calibration are being researched. Overall the MPL systems have proven very effective. A large data base of results from globally distributed sites can be easily accessed through the internet. Applications have included atmospheric model development. Validation of current global satellite observations of aerosol and clouds, including now orbital lidar

The Role of Well Control Training in Developing Safe Onshore and Offshore Oil Drilling Operations

ERIC Educational Resources Information Center

Abulhassn, Aber

2016-01-01

This research investigates the role of the International Well Control Forum (IWCF) Rotary Drilling Well Control Training Program in developing safe oil drilling operations from the perspective of onshore and offshore drilling crews. The research methodology is a qualitative case study. A total of 40 IWCF candidates were interviewed, with 10 from…

A multiproxy approach to evaluate biocidal treatments on biodeteriorated majolica glazed tiles.

PubMed

Coutinho, M L; Miller, A Z; Martin-Sanchez, P M; Mirão, J; Gomez-Bolea, A; Machado-Moreira, B; Cerqueira-Alves, L; Jurado, V; Saiz-Jimenez, C; Lima, A; Phillips, A J L; Pina, F; Macedo, M F

2016-12-01

The Fishing House located on the grounds of the Marquis of Pombal Palace, Oeiras, Portugal, was built in the 18th century. During this epoch, Portuguese gardens, such as the one surrounding the Fishing House, were commonly ornamented with glazed wall tile claddings. Currently, some of these outdoor tile panels are covered with dark colored biofilms, contributing to undesirable aesthetic changes and eventually inducing chemical and physical damage to the tile surfaces. Phylogenetic analyses revealed that the investigated biofilms are mainly composed of green algae, cyanobacteria and dematiaceous fungi. With the aim of mitigating biodeterioration, four different biocides (TiO 2 nanoparticles, Biotin ® T, Preventol ® RI 80 and Albilex Biostat ® ) were applied in situ to the glazed wall tiles. Their efficacy was monitored by visual examination, epifluorescence microscopy and DNA-based analysis. Significant changes in the microbial community composition were observed 4 months after treatment with Preventol ® RI 80 and Biotin ® T. Although the original community was inactivated after these treatments, an early stage of re-colonization was detected 6 months after the biocide application. TiO 2 nanoparticles showed promising results due to their self-cleaning effect, causing the detachment of the biofilm from the tile surface, which remained clean 6 and even 24 months after biocide application. © 2013 Society for Applied Microbiology and John Wiley & Sons Ltd. © 2016 Society for Applied Microbiology and John Wiley & Sons Ltd.

Surface Formation and Preservation of Very-Low-Porosity Thin Crusts ( "Glazes") at the WAIS Divide Site, West Antarctica

NASA Astrophysics Data System (ADS)

Fegyveresi, J. M.; Alley, R. B.; Muto, A.; Spencer, M. K.; Orsi, A. J.

2014-12-01

Observations at the WAIS Divide site show that near-surface snow is strongly altered by weather-related processes, producing features that are recognizable in the ice core. Prominent reflective "glazed" surface crusts develop frequently during the summer. Observations during austral summers 2008-09 through 2012-13, supplemented by Automated Weather Station data with insolation sensors, documented formation of such crusts during relatively low-wind, low-humidity, clear-sky periods with intense daytime sunshine. After formation, such glazed surfaces typically developed cracks in a polygonal pattern with few-meter spacing, likely from thermal contraction at night. Cracking was commonest when several clear days occurred in succession, and was generally followed by surface hoar growth. Temperature and radiation observations showed that solar heating often warmed the near-surface snow above the air temperature, contributing to mass transfer favoring crust formation. Subsequent investigation of the WDC06A deep ice core revealed that preserved surface crusts were seen in the core at an average rate of ~4.3 ± 2 yr-1 over the past 5500 years. They are about 40% more common in layers deposited during summers than during winters. The total summertime crust frequency also covaried with site temperature, with more present during warmer periods. We hypothesize that the mechanism for glaze formation producing single-grain-thick very-low-porosity thin crusts (i.e. "glazes") involves additional in-filling of open pores. The thermal conductivity of ice greatly exceeds that of air, so heat transport in firn is primarily conductive. Because heat flow is primarily through the grain structure, for a temperature inversion (colder upper surface) beneath a growing thin crust at the upper surface, pores will be colder than interconnected grains, favoring mass transport into those pores. Transport may occur by vapor, surface, or volume diffusion, although vapor diffusion and surface

Safe Energy Source in Battery-operated Toys for Children.

PubMed

Rossi, Alfredo; Vignola, Silvia; Nason, Francesca; Boschetti, Federica; Bramerio, Manuela; Bailini, Alessandro; Pinarello, Giordano

2017-11-01

Serious and even fatal consequences of disk batteries ingestion in children are well known. Among other applications, disk batteries are used to power small toys, from which they can be unexpectedly extracted and swallowed. We tested a new cell intended for little toys (green cell [GC]), after 6 and 12 hours of in vitro close contact with esophageal swine mucosa. The GC was compared with lithium and silver button batteries under the same experimental conditions. Tissues in contact with the GC did not show pH variations nor histological alterations after 6 and 12 hours. In such conditions, statistically significant differences were found between the GC and the lithium and silver batteries. So far, multidisciplinary medical effort has been driven to both emergency approach and subsequent operative strategies in children with ingested batteries. Our trial demonstrates the possibility to primarily prevent battery-induced damages by designing new-generation safe cells with no tissue toxicity to power little toys intended for children.

Two dimensional finite element thermal model of laser surface glazing for H13 tool steel

NASA Astrophysics Data System (ADS)

Kabir, I. R.; Yin, D.; Naher, S.

2016-10-01

A two dimensional (2D) transient thermal model with line-heat-source was developed by Finite Element Method (FEM) for laser surface glazing of H13 tool steel using commercial software-ANSYS 15. The geometry of the model was taken as a transverse circular cross-section of cylindrical specimen. Two different power levels (300W, 200W) were used with 0.2mm width of laser beam and 0.15ms exposure time. Temperature distribution, heating and cooling rates, and the dimensions of modified surface were analysed. The maximum temperatures achieved were 2532K (2259°C) and 1592K (1319°C) for laser power 300W and 200W respectively. The maximum cooling rates were 4.2×107 K/s for 300W and 2×107 K/s for 200W. Depths of modified zone increased with increasing laser power. From this analysis, it can be predicted that for 0.2mm beam width and 0.15ms time exposer melting temperature of H13 tool steel is achieved within 200-300W power range of laser beam in laser surface glazing.

Growth ring response in shortleaf pine following glaze icing conditions in western Arkansas and eastern Oklahoma

Treesearch

Douglas J. Stevenson; Thomas B. Lynch; James M. Guldin

2013-01-01

Width reduction in growth rings in shortleaf pine (Pinus echinata Mill.) following glaze ice conditions produces a characteristic pattern dependent on live-crown ratio and extent of crown loss. Ring widths of 133 trees for 3 years preceding and 7 years following the December 2000 ice storm (Bragg and others 2002) in western Arkansas and eastern...

Study on the glaze ice accretion of wind turbine with various chord lengths

NASA Astrophysics Data System (ADS)

Liang, Jian; Liu, Maolian; Wang, Ruiqi; Wang, Yuhang

2018-02-01

Wind turbine icing often occurs in winter, which changes the aerodynamic characteristics of the blades and reduces the work efficiency of the wind turbine. In this paper, the glaze ice model is established for horizontal-axis wind turbine in 3-D. The model contains the grid generation, two-phase simulation, heat and mass transfer. Results show that smaller wind turbine suffers from more serious icing problem, which reflects on a larger ice thickness. Both the collision efficiency and heat transfer coefficient increase under smaller size condition.

Modern problems concerned with ensuring safe operation of heat-generating and mechanical equipment in extending its lifetime

NASA Astrophysics Data System (ADS)

Rezinskikh, V. F.; Grin', E. A.

2013-01-01

The problem concerned with safe and reliable operation of ageing heat-generating and mechanical equipment of thermal power stations is discussed. It is pointed out that the set of relevant regulatory documents serves as the basis for establishing an efficient equipment diagnostic system. In this connection, updating the existing regulatory documents with imparting the required status to them is one of top-priority tasks. Carrying out goal-oriented scientific research works is a necessary condition for solving this problem as well as other questions considered in the paper that are important for ensuring reliable performance of equipment operating for a long period of time. In recent years, the amount of such works has dropped dramatically, although the need for them is steadily growing. Unbiased assessment of the technical state of equipment that has been in operation for a long period of time is an important aspect in solving the problem of ensuring reliable and safe operation of thermal power stations. Here, along with the quality of diagnostic activities, monitoring of technical state performed on the basis of an analysis of statistical field data and results of operational checks plays an important role. The need to concentrate efforts taken in the mentioned problem areas is pointed out, and it is indicated that successful implementation of the outlined measures requires proper organization and efficient operation of a system for managing safety in the electric power industry.

Strategies for Countering Terrorist Safe Havens

DTIC Science & Technology

2013-12-01

tactical containment, pseudo operations, and surrogate security forces. The thesis draws from four historical case studies to examine these strategies...safe havens, tactical containment, pseudo operations, and surrogate security forces. The thesis draws from four historical case studies to examine...pseudo operations—provide viable potential options for USSOF to counter the complex problem of safe havens. Overall, the case studies will demonstrate

PIXE and /μ-PIXE analysis of glazes from terracotta sculptures of the della Robbia workshop

NASA Astrophysics Data System (ADS)

Zucchiatti, Alessandro; Bouquillon, Anne; Giancarlo Lanterna; Lucarelli, Franco; Mandò, Pier Andrea; Prati, Paolo; Salomon, Joseph; Vaccari, Maria Grazia

2002-04-01

A series of PIXE analyses has been performed on glazes from terracotta sculptures of the Italian Renaissance and on reference standards. The problems related to the investigation of such heterogeneous materials are discussed and the experimental uncertainties are evaluated, for each element, from the PIXE analysis of standard glasses. Some examples from artefacts coming from Italian collections are given. This research has been conducted in the framework of the COST-G1 European action.

[Prevention of adverse effects in latex allergic patients: organizing a latex safe operating theatre].

PubMed

Bonalumi, Sabrina; Barbonaglia, Patrizia; Bertocchi, Carmen

2006-01-01

In 2001 the General Health Direction of Region Lombardia approved (decree n. 22303) a guideline for the prevention of latex allergic reactions in patients and health care workers. This document provides general recommendations in order to standardize behaviors in regional health care facilities. The reason is due to a rise in the incident of reactions to latex products in the last 20 years. Nowadays the prevalence is higher in certain risk groups (subjected to frequent and repeated exposures) rather than the general population. The aim of the project was to organize a latex safe operating theatre in the Ospedale Maggiore Policlinico, Mangiagalli e Regina Elena of Milan (Fondazione) and to standardize behaviors in order to prevent adverse effects in latex allergic patients. Thanks to the literature review and the creation of a multidisciplinar team, we produced a protocol. Therefore, we requested manufacturers the certification of the latex content of their products. Results and conclusion. When latex allergic patients need to undergone surgery in our hospital, a latex safe operating theatre is organized by personnel following a multidisciplinar protocol. No allergic reactions were experienced during surgical procedures after the creation of an environment as free as possible from latex contamination. The project will involve an emergency room, one room or more of a ward and of the outpatients department.

Learning from the past: Rare ε-Fe2O3 in the ancient black-glazed Jian (Tenmoku) wares

PubMed Central

Dejoie, Catherine; Sciau, Philippe; Li, Weidong; Noé, Laure; Mehta, Apurva; Chen, Kai; Luo, Hongjie; Kunz, Martin; Tamura, Nobumichi; Liu, Zhi

2014-01-01

Ancient Jian wares are famous for their lustrous black glaze that exhibits unique colored patterns. Some striking examples include the brownish colored “Hare's Fur” (HF) strips and the silvery “Oil Spot” (OS) patterns. Herein, we investigated the glaze surface of HF and OS samples using a variety of characterization methods. Contrary to the commonly accepted theory, we identified the presence of ε-Fe2O3, a rare metastable polymorph of Fe2O3 with unique magnetic properties, in both HF and OS samples. We found that surface crystals of OS samples are up to several micrometers in size and exclusively made of ε-Fe2O3. Interestingly, these ε-Fe2O3 crystals on the OS sample surface are organized in a periodic two dimensional fashion. These results shed new lights on the actual mechanisms and kinetics of polymorphous transitions of Fe2O3. Deciphering technologies behind the fabrication of ancient Jian wares can thus potentially help researchers improve the ε-Fe2O3 synthesis. PMID:24820819

Defining a Safe Operating Space for inland recreational fisheries

USGS Publications Warehouse

Carpenter, Stephen R.; Brock, William A.; Hansen, Gretchen J. A.; Hansen, Jonathan F.; Hennessy, Joseph M.; Isermann, Daniel A.; Pedersen, Eric J.; Perales, K. Martin; Rypel, Andrew L.; Sass, Greg G.; Tunney, Tyler D.; Vander Zanden, M. Jake

2017-01-01

The Safe Operating Space (SOS) of a recreational fishery is the multidimensional region defined by levels of harvest, angler effort, habitat, predation and other factors in which the fishery is sustainable into the future. SOS boundaries exhibit trade-offs such that decreases in harvest can compensate to some degree for losses of habitat, increases in predation and increasing value of fishing time to anglers. Conversely, high levels of harvest can be sustained if habitat is intact, predation is low, and value of fishing effort is moderate. The SOS approach recognizes limits in several dimensions: at overly high levels of harvest, habitat loss, predation, or value of fishing effort, the stock falls to a low equilibrium biomass. Recreational fisheries managers can influence harvest and perhaps predation, but they must cope with trends that are beyond their control such as changes in climate, loss of aquatic habitat or social factors that affect the value of fishing effort for anglers. The SOS illustrates opportunities to manage harvest or predation to maintain quality fisheries in the presence of trends in climate, social preferences or other factors that are not manageable.

Glaze Damage In 13- To 18-Year-Old, Natural, Even-Aged Stands of Loblolly Pines in Southeastern Arkansas

Treesearch

Michael D. Cain; Michael G. Shelton

2002-01-01

In late December 1998, a severe winter storm deposited 2.1 inches of precipitation on the Crossett Experimental Forest in southeastern Arkansas. Ice, in the form of glaze, accumulated on needles and branches of trees, and resulted in visual damage to sapling and pulpwood-sized pines. Within 60 days after the storm, damage was assessed within naturally regenerated,...

VISIR: technological infrastructure of an operational service for safe and efficient navigation in the Mediterranean Sea

NASA Astrophysics Data System (ADS)

Mannarini, Gianandrea; Turrisi, Giuseppe; D'Anca, Alessandro; Scalas, Mario; Pinardi, Nadia; Coppini, Giovanni; Palermo, Francesco; Carluccio, Ivano; Scuro, Matteo; Cretì, Sergio; Lecci, Rita; Nassisi, Paola; Tedesco, Luca

2016-08-01

VISIR (discoVerIng Safe and effIcient Routes) is an operational decision support system (DSS) for optimal ship routing designed and implemented in the frame of the TESSA (TEchnology for Situational Sea Awareness) project. The system is aimed to increase safety and efficiency of navigation through the use of forecast environmental fields and route optimization. VISIR can be accessed through a web interface (www.visir-nav.com) and mobile applications for both iOS and Android devices. This paper focuses on the technological infrastructure developed for operating VISIR as a DSS. Its main components are described, the performance of the operational system is assessed through experimental measurements, and a few case studies are presented.

Managing Cassini Safe Mode Attitude at Saturn

NASA Technical Reports Server (NTRS)

Burk, Thomas A.

2010-01-01

The Cassini spacecraft was launched on October 15, 1997 and arrived at Saturn on June 30, 2004. It has performed detailed observations and remote sensing of Saturn, its rings, and its satellites since that time. In the event safe mode interrupts normal orbital operations, Cassini has flight software fault protection algorithms to detect, isolate, and recover to a thermally safe and commandable attitude and then wait for further instructions from the ground. But the Saturn environment is complex, and safety hazards change depending on where Cassini is in its orbital trajectory around Saturn. Selecting an appropriate safe mode attitude that insures safe operation in the Saturn environment, including keeping the star tracker field of view clear of bright bodies, while maintaining a quiescent, commandable attitude, is a significant challenge. This paper discusses the Cassini safe table management strategy and the key criteria that must be considered, especially during low altitude flybys of Titan, in deciding what spacecraft attitude should be used in the event of safe mode.

From Planetary Boundaries to national fair shares of the global safe operating space - How can the scales be bridged?

NASA Astrophysics Data System (ADS)

Häyhä, Tiina; Cornell, Sarah; Lucas, Paul; van Vuuren, Detlef; Hoff, Holger

2016-04-01

The planetary boundaries framework proposes precautionary quantitative global limits to the anthropogenic perturbation of crucial Earth system processes. In this way, it marks out a planetary 'safe operating space' for human activities. However, decisions regarding resource use and emissions are mostly made at much smaller scales, mostly by (sub-)national and regional governments, businesses, and other local actors. To operationalize the planetary boundaries, they need to be translated into and aligned with targets that are relevant at these smaller scales. In this paper, we develop a framework that addresses the three dimension of bridging across scales: biophysical, socio-economic and ethical, to provide a consistent universally applicable approach for translating the planetary boundaries into national level context-specific and fair shares of the safe operating space. We discuss our findings in the context of previous studies and their implications for future analyses and policymaking. In this way, we help link the planetary boundaries framework to widely- applied operational and policy concepts for more robust strong sustainability decision-making.

Development of Craze and Impact Resistance in Glazing Plastics by Multiaxial Stretching

NASA Technical Reports Server (NTRS)

Kline, G M; Wolock, I; Axilrod, B M; Sherman, M A; George, D A; Cohen, V

1956-01-01

The loss of strength of cast polymethyl methacrylate plastic as a result of crazing is of considerable importance to the aircraft industry. Because of the critical need for basic information on the nature of crazing and the effects of various treatments and environmental conditions on its incidence and magnitude, an investigation of this phenomenon was undertaken. The following factors were examined: (1) the effect of stress-solvent crazing on tensile strength of polymethyl methacrylate; (2) the critical stress and strain for onset of crazing at various temperatures; (3) the effect of molecular weight on crazing; and (4) the effect of multiaxial stretching on crazing of polymethyl methacrylate and other acrylic glazing materials.

Review of Issues Associated with Safe Operation and Management of the Space Shuttle Program

NASA Technical Reports Server (NTRS)

Johnstone, Paul M.; Blomberg, Richard D.; Gleghorn, George J.; Krone, Norris J.; Voltz, Richard A.; Dunn, Robert F.; Donlan, Charles J.; Kauderer, Bernard M.; Brill, Yvonne C.; Englar, Kenneth G.;

The study of chemical composition and elemental mappings of colored over-glaze porcelain fired in Qing Dynasty by micro-X-ray fluorescence

NASA Astrophysics Data System (ADS)

Lin, Cheng; Meitian, Li; Youshi, Kim; Changsheng, Fan; Shanghai, Wang; Qiuli, Pan; Zhiguo, Liu; Rongwu, Li

2011-02-01

It is very difficult to measure the chemical composition of colored pigments of over-glaze porcelain by X-ray fluorescence because it contains high concentration of Pb. One of the disadvantages of our polycapillary optics is that it has low transmission efficiency to the high energy X-ray. However, it is beneficial to measure the chemical compositions of rich Pb sample. In this paper, we reported the performances of a tabletop setup of micro-X-ray fluorescence system base on slightly focusing polycapillary and its applications for analysis of rich Pb sample. A piece of Chinese ancient over-glaze porcelain was analyzed by micro-X-ray fluorescence. The experimental results showed that the Cu, Fe and Mn are the major color elements. The possibilities of the process of decorative technology were discussed in this paper, also.

Evaluation of the Water Film Weber Number in Glaze Icing Scaling

NASA Technical Reports Server (NTRS)

Tsao, Jen-Ching; Kreeger, Richard E.; Feo, Alejandro

2010-01-01

Icing scaling tests were performed in the NASA Glenn Icing Research Tunnel to evaluate a new scaling method, developed and proposed by Feo for glaze icing, in which the scale liquid water content and velocity were found by matching reference and scale values of the nondimensional water-film thickness expression and the film Weber number. For comparison purpose, tests were also conducted using the constant We(sub L) method for velocity scaling. The reference tests used a full-span, fiberglass, 91.4-cm-chord NACA 0012 model with velocities of 76 and 100 knot and MVD sizes of 150 and 195 microns. Scale-to-reference model size ratio was 1:2.6. All tests were made at 0deg AOA. Results will be presented for stagnation point freezing fractions of 0.3 and 0.5.

Application of large-area chromogenics to architectural glazings

NASA Astrophysics Data System (ADS)

Selkowitz, Stephen E.

1990-03-01

Glass plays a significant role in the design of building envelopes today. Since its emergence during the last century as a major building material, glass has evolved into an ubiquitous and versatile building design element, performing functions today that would have been unimaginable a few years ago. The optical clarity and transparency of glass that we take for granted is one of its most unique features. Glass windows keep out the cold wind and rain without blocking the view, but also perform many more complex functions which require variable properties and tradeoffs between conflicting conditions. The glazing that provides view must also provide visual privacy at other times and must sometimes become totally opaque (for audiovisual shows, for example). Transparent glass admits daylight, providing good color rendition and offsetting electric lighting energy needs, but it can also create discomfort and disability glare conditions. The sun provides desirable warmth in winter but its heat is unwelcome in summer when it contributes to thermal discomfort and cooling energy requirements. And glass is an important element in the appearance and aesthetics of a building, both interior and exterior.

Evolution of the Hubble Space Telescope Safing Systems

NASA Technical Reports Server (NTRS)

Pepe, Joyce; Myslinski, Michael

2006-01-01

The Hubble Space Telescope (HST) was launched on April 24 1990, with an expected lifespan of 15 years. Central to the spacecraft design was the concept of a series of on-orbit shuttle servicing missions permitting astronauts to replace failed equipment, update the scientific instruments and keep the HST at the forefront of astronomical discoveries. One key to the success of the Hubble mission has been the robust Safing systems designed to monitor the performance of the observatory and to react to keep the spacecraft safe in the event of equipment anomaly. The spacecraft Safing System consists of a range of software tests in the primary flight computer that evaluate the performance of mission critical hardware, safe modes that are activated when the primary control mode is deemed inadequate for protecting the vehicle, and special actions that the computer can take to autonomously reconfigure critical hardware. The HST Safing System was structured to autonomously detect electrical power system, data management system, and pointing control system malfunctions and to configure the vehicle to ensure safe operation without ground intervention for up to 72 hours. There is also a dedicated safe mode computer that constantly monitors a keep-alive signal from the primary computer. If this signal stops, the safe mode computer shuts down the primary computer and takes over control of the vehicle, putting it into a safe, low-power configuration. The HST Safing system has continued to evolve as equipment has aged, as new hardware has been installed on the vehicle, and as the operation modes have matured during the mission. Along with the continual refinement of the limits used in the safing tests, several new tests have been added to the monitoring system, and new safe modes have been added to the flight software. This paper will focus on the evolution of the HST Safing System and Safing tests, and the importance of this evolution to prolonging the science operations of the

Micro-XRF for characterization of Moroccan glazed ceramics and Portuguese tiles

NASA Astrophysics Data System (ADS)

Guilherme, A.; Manso, M.; Pessanha, S.; Zegzouti, A.; Elaatmani, M.; Bendaoud, R.; Coroado, J.; dos Santos, J. M. F.; Carvalho, M. L.

2013-02-01

A set of enamelled terracotta samples (Zellij) collected from five different monuments in Morocco were object of study. With the aim of characterizing these typically Moroccan artistic objects, X-ray spectroscopic techniques were used as analytical tool to provide elemental and compound information. A lack of information about these types of artistic ceramics is found by the research through international scientific journals, so this investigation is an opportunity to fulfill this gap. For this purpose, micro-Energy Dispersive X-ray Fluorescence (μ-EDXRF), and wavelength dispersive X-ray Fluorescence (WDXRF) and X-ray Diffraction (XRD) were the chosen methods. As complementary information, a comparison with other sort of artistic pottery objects is given, more precisely with Portuguese glazed wall tiles (Azulejos), based in the Islamic pottery traditions. Differences between these two types of decorative pottery were found and presented in this manuscript.

Operational and Medical Procedures for a Declared Contingency Shuttle (CSCS) Shuttle Mission Due to a Failure that Precludes a Safe Return

NASA Technical Reports Server (NTRS)

Adams, Adrien; Patlach, Bob; Duchense, Ted; Chandler, Mike; Stepaniak, Philip C.

2011-01-01

This poster paper outlines the operational and medical procedures for a shuttle mission that has a failure that precludes a safe return to Earth. Information about the assumptions, procedures and limiting consumables is included.

Microelectromechanical safe arm device

DOEpatents

Roesler, Alexander W [Tijeras, NM

2012-06-05

Microelectromechanical (MEM) apparatus and methods for operating, for preventing unintentional detonation of energetic components comprising pyrotechnic and explosive materials, such as air bag deployment systems, munitions and pyrotechnics. The MEM apparatus comprises an interrupting member that can be moved to block (interrupt) or complete (uninterrupt) an explosive train that is part of an energetic component. One or more latching members are provided that engage and prevent the movement of the interrupting member, until the one or more latching members are disengaged from the interrupting member. The MEM apparatus can be utilized as a safe and arm device (SAD) and electronic safe and arm device (ESAD) in preventing unintentional detonations. Methods for operating the MEM apparatus include independently applying drive signals to the actuators coupled to the latching members, and an actuator coupled to the interrupting member.

Curiosity's Autonomous Surface Safing Behavior Design

NASA Technical Reports Server (NTRS)

Neilson, Tracy A.; Manning, Robert M.

2013-01-01

The safing routines on all robotic deep-space vehicles are designed to put the vehicle in a power and thermally safe configuration, enabling communication with the mission operators on Earth. Achieving this goal is made a little more difficult on Curiosity because the power requirements for the core avionics and the telecommunication equipment exceed the capability of the single power source, the Multi-Mission Radioisotope Thermoelectric Generator. This drove the system design to create an operational mode, called "sleep mode", where the vehicle turns off most of the loads in order to charge the two Li-ion batteries. The system must keep the vehicle safe from over-heat and under-heat conditions, battery cell failures, under-voltage conditions, and clock failures, both while the computer is running and while the system is sleeping. The other goal of a safing routine is to communicate. On most spacecraft, this simply involves turning on the receiver and transmitter continuously. For Curiosity, Earth is above the horizon only a part of the day for direct communication to the Earth, and the orbiter overpass opportunities only occur a few times a day. The design must robustly place the Rover in a communicable condition at the correct time. This paper discusses Curiosity's autonomous safing behavior and describes how the vehicle remains power and thermally safe while sleeping, as well as a description of how the Rover communicates with the orbiters and Earth at specific times.

Allowing variance may enlarge the safe operating space for exploited ecosystems.

PubMed

Carpenter, Stephen R; Brock, William A; Folke, Carl; van Nes, Egbert H; Scheffer, Marten

2015-11-17

Variable flows of food, water, or other ecosystem services complicate planning. Management strategies that decrease variability and increase predictability may therefore be preferred. However, actions to decrease variance over short timescales (2-4 y), when applied continuously, may lead to long-term ecosystem changes with adverse consequences. We investigated the effects of managing short-term variance in three well-understood models of ecosystem services: lake eutrophication, harvest of a wild population, and yield of domestic herbivores on a rangeland. In all cases, actions to decrease variance can increase the risk of crossing critical ecosystem thresholds, resulting in less desirable ecosystem states. Managing to decrease short-term variance creates ecosystem fragility by changing the boundaries of safe operating spaces, suppressing information needed for adaptive management, cancelling signals of declining resilience, and removing pressures that may build tolerance of stress. Thus, the management of variance interacts strongly and inseparably with the management of resilience. By allowing for variation, learning, and flexibility while observing change, managers can detect opportunities and problems as they develop while sustaining the capacity to deal with them.

Allowing variance may enlarge the safe operating space for exploited ecosystems

PubMed Central

Carpenter, Stephen R.; Brock, William A.; Folke, Carl; van Nes, Egbert H.; Scheffer, Marten

2015-01-01

Variable flows of food, water, or other ecosystem services complicate planning. Management strategies that decrease variability and increase predictability may therefore be preferred. However, actions to decrease variance over short timescales (2–4 y), when applied continuously, may lead to long-term ecosystem changes with adverse consequences. We investigated the effects of managing short-term variance in three well-understood models of ecosystem services: lake eutrophication, harvest of a wild population, and yield of domestic herbivores on a rangeland. In all cases, actions to decrease variance can increase the risk of crossing critical ecosystem thresholds, resulting in less desirable ecosystem states. Managing to decrease short-term variance creates ecosystem fragility by changing the boundaries of safe operating spaces, suppressing information needed for adaptive management, cancelling signals of declining resilience, and removing pressures that may build tolerance of stress. Thus, the management of variance interacts strongly and inseparably with the management of resilience. By allowing for variation, learning, and flexibility while observing change, managers can detect opportunities and problems as they develop while sustaining the capacity to deal with them. PMID:26438857

Compliant Task Execution and Learning for Safe Mixed-Initiative Human-Robot Operations

NASA Technical Reports Server (NTRS)

Dong, Shuonan; Conrad, Patrick R.; Shah, Julie A.; Williams, Brian C.; Mittman, David S.; Ingham, Michel D.; Verma, Vandana

2011-01-01

We introduce a novel task execution capability that enhances the ability of in-situ crew members to function independently from Earth by enabling safe and efficient interaction with automated systems. This task execution capability provides the ability to (1) map goal-directed commands from humans into safe, compliant, automated actions, (2) quickly and safely respond to human commands and actions during task execution, and (3) specify complex motions through teaching by demonstration. Our results are applicable to future surface robotic systems, and we have demonstrated these capabilities on JPL's All-Terrain Hex-Limbed Extra-Terrestrial Explorer (ATHLETE) robot.

Safely Enabling Low-Altitude Airspace Operations

NASA Technical Reports Server (NTRS)

Kopardekar, Parimal

2015-01-01

Near-term Goal: Enable initial low-altitude airspace and UAS operations with demonstrated safety as early as possible, within 5 years. Long-term Goal: Accommodate increased UAS operations with highest safety, efficiency, and capacity as much autonomously as possible (10-15 years).

The National Aeronautics and Space Administration Nondestructive Evaluation Program for Safe and Reliable Operations

NASA Technical Reports Server (NTRS)

Generazio, Ed

2005-01-01

The National Aeronautics and Space Administration (NASA) Nondestructive Evaluation (NDE) Program is presented. As a result of the loss of seven astronauts and the Space Shuttle Columbia on February 1, 2003, NASA has undergone many changes in its organization. NDE is one of the key areas that are recognized by the Columbia Accident Investigation Board (CAIB) that needed to be strengthened by warranting NDE as a discipline with Independent Technical Authority (iTA). The current NASA NDE system and activities are presented including the latest developments in inspection technologies being applied to the Space Transportation System (STS). The unfolding trends and directions in NDE for the future are discussed as they apply to assuring safe and reliable operations.

Reactive, Safe Navigation for Lunar and Planetary Robots

NASA Technical Reports Server (NTRS)

Utz, Hans; Ruland, Thomas

2008-01-01

When humans return to the moon, Astronauts will be accompanied by robotic helpers. Enabling robots to safely operate near astronauts on the lunar surface has the potential to significantly improve the efficiency of crew surface operations. Safely operating robots in close proximity to astronauts on the lunar surface requires reactive obstacle avoidance capabilities not available on existing planetary robots. In this paper we present work on safe, reactive navigation using a stereo based high-speed terrain analysis and obstacle avoidance system. Advances in the design of the algorithms allow it to run terrain analysis and obstacle avoidance algorithms at full frame rate (30Hz) on off the shelf hardware. The results of this analysis are fed into a fast, reactive path selection module, enforcing the safety of the chosen actions. The key components of the system are discussed and test results are presented.

The South Australian Safe Drinking Water Act: summary of the first year of operation.

PubMed

Froscio, Suzanne M; Bolton, Natalie; Cooke, Renay; Wittholz, Michelle; Cunliffe, David

2016-06-01

The Safe Drinking Water Act 2011 was introduced in South Australia to provide clear direction to drinking water providers on how to achieve water safety. The Act requires drinking water providers to register with SA Health and develop a risk management plan (RMP) for their water supply that includes operational and verification monitoring plans and an incident notification and communication protocol. During the first year of operation, 212 drinking water providers registered under the Act, including one major water utility and a range of small to medium sized providers in regional and remote areas of the State. Information was captured on water source(s) used and water treatment. Rainwater was the most frequently reported drinking water source (66%), followed by bore water (13%), on-supply or carting of mains water (13%), mixed source (rainwater with bore water backup) (6%) and surface water (3%). The majority of providers (91%) treated the water supply, 87% used disinfection. During the first year of operation, 16 water quality incidents were formally reported to SA Health. These included both microbial and chemical incidents. Case studies presented highlight how the RMPs are assisting drinking water providers to identify incidents of potential health concern and implement corrective actions.

Development and testing of a photometric method to identify non-operating solar hot water systems in field settings.

DOE Office of Scientific and Technical Information (OSTI.GOV)

He, Hongbo; Vorobieff, Peter V.; Menicucci, David

2012-06-01

This report presents the results of experimental tests of a concept for using infrared (IR) photos to identify non-operational systems based on their glazing temperatures; operating systems have lower glazing temperatures than those in stagnation. In recent years thousands of new solar hot water (SHW) systems have been installed in some utility districts. As these numbers increase, concern is growing about the systems dependability because installation rebates are often based on the assumption that all of the SHW systems will perform flawlessly for a 20-year period. If SHW systems routinely fail prematurely, then the utilities will have overpaid for grid-energymore » reduction performance that is unrealized. Moreover, utilities are responsible for replacing energy for loads that failed SHW system were supplying. Thus, utilities are seeking data to quantify the reliability of SHW systems. The work described herein is intended to help meet this need. The details of the experiment are presented, including a description of the SHW collectors that were examined, the testbed that was used to control the system and record data, the IR camera that was employed, and the conditions in which testing was completed. The details of the associated analysis are presented, including direct examination of the video records of operational and stagnant collectors, as well as the development of a model to predict glazing temperatures and an analysis of temporal intermittency of the images, both of which are critical to properly adjusting the IR camera for optimal performance. Many IR images and a video are presented to show the contrast between operating and stagnant collectors. The major conclusion is that the technique has potential to be applied by using an aircraft fitted with an IR camera that can fly over an area with installed SHW systems, thus recording the images. Subsequent analysis of the images can determine the operational condition of the fielded collectors. Specific

Modeling Relevant to Safe Operations of U.S. Navy Vessels in Arctic Conditions: Physical Modeling of Ice Loads

DTIC Science & Technology

2016-06-01

zones with ice concentrations up to 40%. To achieve this goal, the Navy must determine safe operational speeds as a function of ice concen- tration...and full-scale experience with ice-capable hull forms that have shallow entry angles to promote flexural ice failure preferentially over crushing...plan view) of the proposed large-scale ice–hull impact experiment to be conducted in CRREL’s refrigerated towing basin. Shown here is a side-panel

Light scattering properties of new materials for glazing applications

NASA Astrophysics Data System (ADS)

Bergkvist, Mikael; Roos, Arne

1991-12-01

Several new materials are available for glazing applications, many of which require careful optical characterization, especially with regards to light scattering. Measuring scattering requires special equipment and is inherently difficult. An integrating sphere can be used for the total and diffuse components but great care must be taken in interpreting the instrument readings. Angular resolved scattering measurements are necessary for a complete characterization, and this is difficult for low levels of scattering. In this paper, measurements on electrically switchable NCAP materials and thick panes of aerogel are reported. The NCAP films switch reversibly from a translucent, scattering state to a transparent, clear state with the application of an ac-voltage. Airglass has a porous SiO2 structure with a refractive index n equals 1.04 and a very low heat transfer coefficient. Integrated scattering measurements were performed in the wavelength range 300 to 2500 nm on a Beckman 5240 spectrophotometer equipped with a 198851 integrating sphere. In this instrument we can measure the total and diffuse components of the reflectance or transmittance separately. The angular distribution of the scattered light was measured in a scatterometer, which can perform scattering measurements in the wavelength range 400-1100 nm in both transmittance and reflectance mode with variable angle of incidence.

Improvement of sound insulation performance of double-glazed windows by using viscoelastic connectors

NASA Astrophysics Data System (ADS)

Takahashi, D.; Sawaki, S.; Mu, R.-L.

2016-06-01

A new method for improving the sound insulation performance of double-glazed windows is proposed. This technique uses viscoelastic materials as connectors between the two glass panels to ensure that the appropriate spacing is maintained. An analytical model that makes it possible to discuss the effects of spacing, contact area, and viscoelastic properties of the connectors on the performance in terms of sound insulation is developed. The validity of the model is verified by comparing its results with measured data. The numerical experiments using this analytical model showed the importance of the ability of the connectors to achieve the appropriate spacing and their viscoelastic properties, both of which are necessary for improving the sound insulation performance. In addition, it was shown that the most effective factor is damping: the stronger the damping, the more the insulation performance increases.

A guide to safe field operations

USGS Publications Warehouse

Yobbi, D.K.; Yorke, T.H.; Mycyk, R.T.

1996-01-01

Most functions of the U.S. Geological Survey (USGS), Water Resources Division (WRD) require employees to participate in numerous field activities ranging from routine meetings with cooperators, other federal and public officials, and private citizens to potentially hazardous assignments, such as making flood measurements and scuba diving to service underwater instruments. It is paramount that each employee be aware of safety procedures and operational policies of the WRD to ensure that (1) their activities avoid or minimize personal injury to the employee, coworkers, or anyone in the vicinity of the field activity, and (2) their conduct does not infringe on the personal or property rights of any individual or organization. The purpose of the guide is to familiarize employees with the operational and safety procedures expected to be followed by each employee as a representative of the WRD. It is also intended as a training tool for all new employees and a document to be reviewed by each employee before undertaking a field assignment. It includes general procedures that are standard and applicable to all field operations, such as communication, vehicle operation, and adequate preparation for anticipated weather conditions. It also includes a discussion of specific procedures and safety considerations for most of the routine field assignments undertaken by hydrologists and hydrologic technicians of the WRD. The guide is not intended to be a technical handbook outlining step-by-step procedures for performing specific tasks or a comprehensive discussion of every possible activity that may be undertaken by a USGS employee. Employees are referred to the Techniques for Water-Resources Investigations (TWRI) series for specific technical procedures and to the U.S. Geological Survey Safety and Environmental Health Handbook 445-1-H (USGS, August 1989), USGS Occupational Hazards and Safety Procedures Handbook 445-2-H (December 1993), the WRD notebook on Safety Policy and

Glazed clay pottery and lead exposure in Mexico: Current experimental evidence.

PubMed

Diaz-Ruiz, Araceli; Tristán-López, Luis Antonio; Medrano-Gómez, Karen Itzel; Torres-Domínguez, Juan Alejandro; Ríos, Camilo; Montes, Sergio

2017-11-01

Lead exposure remains a significant environmental problem; lead is neurotoxic, especially in developing humans. In Mexico, lead in human blood is still a concern. Historically, much of the lead exposure is attributed to the use of handcrafted clay pottery for cooking, storing and serving food. However, experimental cause-and-effect demonstration is lacking. The present study explores this issue with a prospective experimental approach. We used handcrafted clay containers to prepare and store lemonade, which was supplied as drinking water to pregnant rats throughout the gestational period. We found that clay pots, jars, and mugs leached on average 200 µg/l lead, and exposure to the lemonade resulted in 2.5 µg/dl of lead in the pregnant rats' blood. Neonates also showed increased lead content in the hippocampus and cerebellum. Caspase-3 activity was found to be statistically increased in the hippocampus in prenatally exposed neonates, suggesting increased apoptosis in that brain region. Glazed ceramics are still an important source of lead exposure in Mexico, and our results confirm that pregnancy is a vulnerable period for brain development.

78 FR 57319 - Children's Online Privacy Protection Rule Safe Harbor Proposed Self-Regulatory Guidelines...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-18

...-AB20 Children's Online Privacy Protection Rule Safe Harbor Proposed Self-Regulatory Guidelines; kidSAFE... proposed self-regulatory guidelines submitted by the kidSAFE Seal Program (``kidSAFE''), owned and operated... part of the SUPPLEMENTARY INFORMATION section below. Write ``kidSAFE Application for Safe Harbor...

Art Safety.

ERIC Educational Resources Information Center

BCATA Journal for Art Teachers, 1991

1991-01-01

Advocating that Canadian art programs should use and model environmentally safe practices, the articles in this journal focus on issues of safe practices in art education. Articles are: (1) "What is WHMIS?"; (2) "Safety Precautions for Specific Art Processes"; (3) "Toxic Substances"; (4) "Using Clay, Glazes, and…

Fail-safe bidirectional valve driver

NASA Technical Reports Server (NTRS)

Fujimoto, H.

1974-01-01

Cross-coupled diodes are added to commonly used bidirectional valve driver circuit to protect circuit and power supply. Circuit may be used in systems requiring fail-safe bidirectional valve operation, particularly in chemical- and petroleum-processing control systems and computer-controlled hydraulic or pneumatic systems.

Operation safe crossing: using science within a community intervention.

PubMed

Voas, Robert B; Tippetts, A Scott; Johnson, Mark B; Lange, James E; Baker, James

2002-09-01

To evaluate a large drunk-driving enforcement program at the US/Mexican border to reduce the number of youths crossing the border to drink in Tijuana. This paper also describes the research data used to develop and manage the program. Data from a border breath-test survey were used to dramatize the problem and gain public support for action. The data were also used to help design the enforcement effort and measure progress in reducing the cross-border drinking problem. The number of news events generated around the occurrence of special enforcement efforts were used to measure project activity and to predict changes in the numbers of youths crossing into Mexico, their returning BACs and reductions in alcohol-related crashes during a 3-year period. An urban county on the Mexican border. Underage youths aged 18-20 years and young adults aged 21-30 years residing in San Diego County. Immigration and Naturalization Services provided population counts of the number of individuals crossing each weekend night from Tijuana into the United States through the San Ysidro border facility. Breath-test surveys of a random sample of these returning crossers provided data on the number of US residents visiting bars and nightclubs in Tijuana and on alcohol consumption at Tijuana bars and nightclubs. Night-time had-been-drinking crash data involving young drivers in several California counties served as an outcome measure of public health and safety. Analysis of data involving more than 2 million pedestrians returning from Tijuana indicated that the Operation Safe Crossing program reduced the number of late-night crossers by 31.6%. Effective use of data through media advocacy programs to support an enforcement effort can reduce alcohol-related crashes.

InaSAFE applications in disaster preparedness

NASA Astrophysics Data System (ADS)

Pranantyo, Ignatius Ryan; Fadmastuti, Mahardika; Chandra, Fredy

2015-04-01

Disaster preparedness activities aim to reduce the impact of disasters by being better prepared to respond when a disaster occurs. In order to better anticipate requirements during a disaster, contingency planning activities can be undertaken prior to a disaster based on a realistic disaster scenario. InaSAFE is a tool that can inform this process. InaSAFE is a free and open source software that estimates the impact to people and infrastructure from potential hazard scenarios. By using InaSAFE, disaster managers can develop scenarios of disaster impacts (people and infrastructures affected) to inform their contingency plan and emergency response operation plan. While InaSAFE provides the software framework exposure data and hazard data are needed as inputs to run this software. Then InaSAFE can be used to forecast the impact of the hazard scenario to the exposure data. InaSAFE outputs include estimates of the number of people, buildings and roads are affected, list of minimum needs (rice and clean water), and response checklist. InaSAFE is developed by Indonesia's National Disaster Management Agency (BNPB) and the Australian Government, through the Australia-Indonesia Facility for Disaster Reduction (AIFDR), in partnership with the World Bank - Global Facility for Disaster Reduction and Recovery (GFDRR). This software has been used in many parts of Indonesia, including Padang, Maumere, Jakarta, and Slamet Mountain for emergency response and contingency planning.

Safe Use of Hydrogen and Hydrogen Systems

NASA Technical Reports Server (NTRS)

Maes, Miguel

2006-01-01

This is a viewgraph presentation that is a course for teaching the safe use of hydrogen. The objectives of the course are 1. To familiarize the student with H2 safety properties 2. To enable the identification, evaluations and addressing of H2 system hazards 3. To teach: a. Safe practices for, b. Design, c. Materials selection, d. H2 system operation, e. Physical principles and empirical observations on which these safe practices are based, f. How to respond to emergency situations involving H2, g How to visualize safety concepts through in-class exercises, h. Identify numerous parameters important to H2 safety.

Safe sex

MedlinePlus

... sex; Sexually transmitted - safe sex; GC - safe sex; Gonorrhea - safe sex; Herpes - safe sex; HIV - safe sex; ... contact. STIs include: Chlamydia Genital herpes Genital warts Gonorrhea Hepatitis HIV HPV Syphilis STIs are also called ...

Safe Schools for LGBTQI Students: How Do Teachers View Their Role in Promoting Safe Schools?

ERIC Educational Resources Information Center

Vega, Stephanie; Crawford, Heather Glynn; Van Pelt, J-Lynn

2012-01-01

This literature review presents insights from existing research on how teachers view their role in creating safe schools for lesbian, gay, bisexual, transgender, queer/questioning, and intersex (LGBTQI) students. Analysis of the literature shows that there are concerns for LGBTQI students' safety in schools, that educational settings operate from…

Combination of glazing, nisin treatment and radiation processing for shelf-life extension of seer fish (Scomberomorous guttatus) steaks

NASA Astrophysics Data System (ADS)

Kakatkar, Aarti S.; Gautam, Raj Kamal; Shashidhar, Ravindranath

2017-01-01

Fish and fishery products are most perishable. Combination of chilling with gamma irradiation, edible coatings, addition of antimicrobials etc has been applied to extend the shelf life. In the present study, a process to enhance the shelf life of seer fish (Scomberomorus guttatus) steaks using combination of coating prepared from gel dispersion of same fish; incorporated with nisin and gamma irradiation is described. A combination of glazing incorporated with nisin and irradiation at 2 kGy and 5 kGy increased the shelf life of the steaks from 7 days up to 34 and 42 days respectively on chilled storage.

LWC and Temperature Effects on Ice Accretion Formation on Swept Wings at Glaze Ice Conditions

NASA Technical Reports Server (NTRS)

Vargas, Mario; Reshotko, Eli

2000-01-01

An experiment was conducted to study the effect of liquid water content and temperature on the critical distance in ice accretion formation on swept wings at glaze ice conditions. The critical distance is defined as the distance from the attachment line to tile beginning of the zone where roughness elements develop into glaze ice feathers. A baseline case of 150 mph, 25 F, 0.75 g/cu m. Cloud Liquid Water Content (LWC) and 20 micrometers in Water Droplet Median Volume Diameter (MVD) was chosen. Icing runs were performed on a NACA 0012 swept wing tip at 150 mph and MVD of 20 micrometers for liquid water contents of 0.5 g/cu m, 0.75 g/cu m, and 1.0 g/cu m, and for total temperatures of 20 F, 25 F and 30 F. At each tunnel condition, the sweep angle was changed from 0 deg to 45 deg in 5 deg increments. Casting data, ice shape tracings, and close-up photographic data were obtained. The results showed that decreasing the LWC to 0.5 g/cu m decreases the value of the critical distance at a given sweep angle compared to the baseline case, and starts the formation of complete scallops at 30 sweep angle. Increasing the LWC to 1.0 g/cu m increases the value of the critical distance compared to the baseline case, the critical distance remains always above 0 millimeters and complete scallops are not formed. Decreasing the total temperature to 20 F decreases the critical distance with respect to the baseline case and formation of complete scallops begins at 25 deg sweep angle. When the total temperature is increased to 30 F, bumps covered with roughness elements appear on the ice accretion at 25 deg and 30 deg sweep angles, large ice structures appear at 35 deg and 40 deg sweep angles, and complete scallops are formed at 45 deg sweep angle.

Iterative co-creation for improved hand hygiene and aseptic techniques in the operating room: experiences from the safe hands study.

PubMed

Erichsen Andersson, Annette; Frödin, Maria; Dellenborg, Lisen; Wallin, Lars; Hök, Jesper; Gillespie, Brigid M; Wikström, Ewa

2018-01-04

Hand hygiene and aseptic techniques are essential preventives in combating hospital-acquired infections. However, implementation of these strategies in the operating room remains suboptimal. There is a paucity of intervention studies providing detailed information on effective methods for change. This study aimed to evaluate the process of implementing a theory-driven knowledge translation program for improved use of hand hygiene and aseptic techniques in the operating room. The study was set in an operating department of a university hospital. The intervention was underpinned by theories on organizational learning, culture and person centeredness. Qualitative process data were collected via participant observations and analyzed using a thematic approach. Doubts that hand-hygiene practices are effective in preventing hospital acquired infections, strong boundaries and distrust between professional groups and a lack of psychological safety were identified as barriers towards change. Facilitated interprofessional dialogue and learning in "safe spaces" worked as mechanisms for motivation and engagement. Allowing for the free expression of different opinions, doubts and viewing resistance as a natural part of any change was effective in engaging all professional categories in co-creation of clinical relevant solutions to improve hand hygiene. Enabling nurses and physicians to think and talk differently about hospital acquired infections and hand hygiene requires a shift from the concept of one-way directed compliance towards change and learning as the result of a participatory and meaning-making process. The present study is a part of the Safe Hands project, and is registered with ClinicalTrials.gov (ID: NCT02983136 ). Date of registration 2016/11/28, retrospectively registered.

30 CFR 250.456 - What safe practices must the drilling fluid program follow?

Code of Federal Regulations, 2010 CFR

2010-07-01

... INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Drilling Fluid Requirements § 250.456 What safe practices must the drilling fluid program follow... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What safe practices must the drilling fluid...

Inertial sensing microelectromechanical (MEM) safe-arm device

DOEpatents

Roesler, Alexander W [Tijeras, NM; Wooden, Susan M [Sandia Park, NM

2009-05-12

Microelectromechanical (MEM) safe-arm devices comprise a substrate upon which a sense mass, that can contain an energetic material, is constrained to move along a pathway defined by a track disposed on the surface of the substrate. The pathway has a first end comprising a "safe" position and a second end comprising an "armed" position, whereat the second end the sense mass can be aligned proximal to energetic materials comprising the explosive train, within an explosive component. The sense mass can be confined in the safe position by a first latch, operable to release the sense mass by an acceleration acting in a direction substantially normal to the surface of the substrate. A second acceleration, acting in a direction substantially parallel to the surface of the substrate, can cause the sense mass to traverse the pathway from the safe position to the armed position.

Digital computer operation of a nuclear reactor

DOEpatents

Colley, R.W.

1982-06-29

A method is described for the safe operation of a complex system such as a nuclear reactor using a digital computer. The computer is supplied with a data base containing a list of the safe state of the reactor and a list of operating instructions for achieving a safe state when the actual state of the reactor does not correspond to a listed safe state, the computer selects operating instructions to return the reactor to a safe state.

Digital computer operation of a nuclear reactor

DOEpatents

Colley, Robert W.

1984-01-01

A method is described for the safe operation of a complex system such as a nuclear reactor using a digital computer. The computer is supplied with a data base containing a list of the safe state of the reactor and a list of operating instructions for achieving a safe state when the actual state of the reactor does not correspond to a listed safe state, the computer selects operating instructions to return the reactor to a safe state.

UAV Research at NASA Langley: Towards Safe, Reliable, and Autonomous Operations

NASA Technical Reports Server (NTRS)

Davila, Carlos G.

2016-01-01

Unmanned Aerial Vehicles (UAV) are fundamental components in several aspects of research at NASA Langley, such as flight dynamics, mission-driven airframe design, airspace integration demonstrations, atmospheric science projects, and more. In particular, NASA Langley Research Center (Langley) is using UAVs to develop and demonstrate innovative capabilities that meet the autonomy and robotics challenges that are anticipated in science, space exploration, and aeronautics. These capabilities will enable new NASA missions such as asteroid rendezvous and retrieval (ARRM), Mars exploration, in-situ resource utilization (ISRU), pollution measurements in historically inaccessible areas, and the integration of UAVs into our everyday lives all missions of increasing complexity, distance, pace, and/or accessibility. Building on decades of NASA experience and success in the design, fabrication, and integration of robust and reliable automated systems for space and aeronautics, Langley Autonomy Incubator seeks to bridge the gap between automation and autonomy by enabling safe autonomous operations via onboard sensing and perception systems in both data-rich and data-deprived environments. The Autonomy Incubator is focused on the challenge of mobility and manipulation in dynamic and unstructured environments by integrating technologies such as computer vision, visual odometry, real-time mapping, path planning, object detection and avoidance, object classification, adaptive control, sensor fusion, machine learning, and natural human-machine teaming. These technologies are implemented in an architectural framework developed in-house for easy integration and interoperability of cutting-edge hardware and software.

49 CFR 230.70 - Safe condition.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., DEPARTMENT OF TRANSPORTATION STEAM LOCOMOTIVE INSPECTION AND MAINTENANCE STANDARDS Steam Locomotives and... of each day the locomotive is used, the steam locomotive operator shall ensure that: (1) The brakes on the steam locomotive and tender are in safe and suitable condition for service; (2) The air...

The Resident-Run Minor Surgery Clinic: A Pilot Study to Safely Increase Operative Autonomy.

PubMed

Wojcik, Brandon M; Fong, Zhi Ven; Patel, Madhukar S; Chang, David C; Petrusa, Emil; Mullen, John T; Phitayakorn, Roy

increased operative autonomy as the greatest strength. Implementation of a resident-run minor surgery clinic is a safe and effective method to increase trainee operative autonomy. The rotation is well suited for mid-level residents, as it provides an opportunity for realistic self-evaluation and focused learning that may enhance their operative experience during senior level rotations. Copyright © 2016 Association of Program Directors in Surgery. Published by Elsevier Inc. All rights reserved.

The voltammetric behaviour of lead at a microband screen-printed carbon electrode and its determination in acetate leachates from glazed ceramic plates.

PubMed

Honeychurch, Kevin C; Al-Berezanchi, Saman; Hart, John P

2011-05-15

Microband screen-printed carbon electrodes (μBSPCEs) without further modification have been investigated as disposable sensors for the measurement of lead in acetate leachates from ceramic glazed plates. Cyclic voltammetry was employed to elucidate the electrochemical behaviour of Pb(2+) at these electrodes in a variety of supporting electrolytes. The anodic peaks obtained on the reverse scans, showed that Pb had been deposited as a thin layer on the surface of the μBSPCE. The anodic peak of greatest magnitude was obtained in 0.1M pH 4.1 acetate buffer containing 13 mM Cl(-). The effect of chromium, copper, phosphate, sulphate and tin was examined and under the conditions employed, no significant change in current was found. The μBSPCEs were evaluated by carrying out lead determinations for acetate leachates from glazed ceramic plates. A highly decorated ornamental plate was found to leach 400 μg Pb(2+) (%CV=1.91%). A second plate, designed for dinnerware was found not to leach any detectable levels of Pb(2+). However, once fortified with 2.10 μg of Pb (equivalent to 100 ng/ml in the leachate), a mean recovery of 82.08% (%CV=4.07%) was obtained. The performance characteristics indicate that reliable data has been obtained for this application which could identify potentially toxic sources of lead. Copyright © 2011 Elsevier B.V. All rights reserved.

Thermomechanical modelling of laser surface glazing for H13 tool steel

NASA Astrophysics Data System (ADS)

Kabir, I. R.; Yin, D.; Tamanna, N.; Naher, S.

2018-03-01

A two-dimensional thermomechanical finite element (FE) model of laser surface glazing (LSG) has been developed for H13 tool steel. The direct coupling technique of ANSYS 17.2 (APDL) has been utilised to solve the transient thermomechanical process. A H13 tool steel cylindrical cross-section has been modelled for laser power 200 W and 300 W at constant 0.2 mm beam width and 0.15 ms residence time. The model can predict temperature distribution, stress-strain increments in elastic and plastic region with time and space. The crack formation tendency also can be assumed by analysing the von Mises stress in the heat-concentrated zone. Isotropic and kinematic hardening models have been applied separately to predict the after-yield phenomena. At 200 W laser power, the peak surface temperature achieved is 1520 K which is below the melting point (1727 K) of H13 tool steel. For laser power 300 W, the peak surface temperature is 2523 K. Tensile residual stresses on surface have been found after cooling, which are in agreement with literature. Isotropic model shows higher residual stress that increases with laser power. Conversely, kinematic model gives lower residual stress which decreases with laser power. Therefore, both plasticity models could work in LSG for H13 tool steel.

29 CFR 1926.1080 - Safe practices manual.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Diving General Operations Procedures § 1926.1080 Safe practices manual. Note: The requirements applicable to construction work under this section are...

Evaluation of the safety benefits of legacy safe routes to school programs

DOT National Transportation Integrated Search

2008-08-01

This study first examined the feasibility of conducting a crash-based assessment of the safety effects of legacy Safe Routes to School : (SRTS) programs. These were SRTS programs operating before the passage of the Safe, Accountable, Flexible, Effici...

A Guide to Safe Field Operations

DTIC Science & Technology

1996-01-01

be dangerous depending on the type of insect and your reaction to their sting or bite. Stinging insects, which include honey bees , killer bees ...and operational policies of the WRD to ensure that (1) their activities avoid or minimize personal injury to the employee, coworkers, or anyone in...assignments with minimal chance of personal injury or infringement on the rights of others. However, once you have received training and have been

Microchemical and microstructural characterisation of medieval and post-medieval ceramic glaze coatings

NASA Astrophysics Data System (ADS)

Alaimo, R.; Bultrini, G.; Fragalà, I.; Giarrusso, R.; Montana, G.

A large number of ceramic samples (from the 10th to the 19th century), found during the excavation of Sicilian archaeological sites (Syracuse, Caltagirone, Sciacca and Piazza Armerina), have been studied by combining scanning electron microscopy, energy-dispersive X-ray spectrometry and optical microscopy. Attention has been focused on the microchemical and microstructural properties of the painted surfaces to investigate the nature of the enamels and pigments in the decorative layers. The general perspective has been the identification of consistent archeometric criteria, other than the standard stylistic considerations, which can be used for a reliable recognition of the production sites. The results collected for each ceramic typology were used to cluster the different ceramic reference groups in a wide database suitable for a reliable discrimination of the provenance of artefacts. Moreover, the same compositional and microstructural data allow the identification of the raw materials used for pigments. There is evidence of some differences with existing information found in the literature concerning the formulas used in ancient times. Finally, attention has also been devoted to identify the technological aspects of the manufacturing techniques and firing conditions adopted for each typology of glaze coating depending on different ceramic materials .

Automatic protective vent has fail-safe feature

NASA Technical Reports Server (NTRS)

Dameron, C. E.

1966-01-01

Delayed vent valve system in a mechanical backing pump in a vacuum system allows the pneumatic foreline valve to seal before the pump vent opens. The system is designed to be fail-safe and operate even though there is loss of electrical power.

Performance of laser glazed Zr02 TBCs in cyclic oxidation and corrosion burner test rigs

NASA Technical Reports Server (NTRS)

Zaplatynsky, I.

1982-01-01

The performance of laser glazed zirconia thermal barrier coatings (TBCs) was evaluated in cyclic oxidation and cyclic corrosion tests. Plasma sprayed zirconia coatings of two thicknesses were partially melted with a CO2 laser. The power density of the focused laser beam was varied from 35 to 75 W/sq mm, while the scanning speed was about 80 cm per minute. In cyclic oxidation tests, the specimens were heated in a burner rig for 6 minutes and cooled for 3 minutes. It is indicated that the laser treated samples have the same life as the untreated ones. However, in corrosion tests, in which the burner rig flame contained 100 PPM sodium fuel equivalent, the laser treated samples exhibit nearly a fourfold life improvement over that of the reference samples vary. In both tests, the lives of the samples inversely with the thickness of the laser melted layer of zirconia.

Safe-haven locking device

DOEpatents

Williams, J.V.

1984-04-26

Disclosed is a locking device for eliminating external control of a secured space formed by fixed and movable barriers. The locking device uses externally and internally controlled locksets and a movable strike, operable from the secured side of the movable barrier, to selectively engage either lockset. A disengagement device, for preventing forces from being applied to the lock bolts is also disclosed. In this manner, a secured space can be controlled from the secured side as a safe-haven. 4 figures.

Effect of incorporation of natural chemicals in water ice-glazing on freshness and shelf-life of Pacific saury (Cololabis saira) during -18 °C frozen storage.

PubMed

Luo, Haibo; Wang, Weihua; Chen, Wei; Tang, Haiqing; Jiang, Li; Yu, Zhifang

2018-07-01

Microbial spoilage and lipid oxidation are two major factors causing freshness deterioration of Pacific saury (Cololabis saira) during frozen storage. To provide a remedy, the effects of several natural chemicals incorporated alone or in combination in traditional water ice-glazing on the freshness and shelf-life of Pacific saury during frozen storage at -18 °C were investigated. Pacific sauries were subjected to individual quick freezing followed immediately by dipping into cold tap water (control) or solutions containing nisin, chitosan, phytic acid (single-factor experiment) or their combinations ((L 9 (3 4 ) orthogonal experiment) for 10 s at 1 °C and then packaged in polypropylene bags before frozen storage at -18 °C. The storage duration tested was up to 12 months. All ice-glazing treatments with individual chemicals could significantly (P < 0.05) inhibit the accumulation of thiobarbituric acid-reactive substances (TBARS), total volatile basic nitrogen (TVB-N) and histamine as well as the increase in bacterial total viable count (TVC) compared with controls, while the combination treatments gave even better effects. The L 9 (3 4 ) orthogonal experiment showed that the optimal combination was A 2 B 1 C 2 (i.e. 0.5 g L -1 nisin, 5 g L -1 chitosan and 0.2 g L -1 phytic acid). The TBARS, TVB-N, histamine and TVC values in A 2 B 1 C 2 -treated samples remained far below the maximum acceptable limit for good-freshness fish after 12 months of frozen storage at -18 °C. The incorporation of natural chemicals tested herein in ice-glazing could inhibit microbial spoilage and lipid oxidation and therefore maintain the freshness of Pacific saury during frozen storage. Under the optimal conditions, the shelf-life of Pacific saury could be extended up to 12 months at -18 °C. The study indicated that the combination treatment with natural chemicals could be commercially utilized to maintain the freshness and prolong the shelf-life of Pacific saury. © 2017 Society of

Selective non-operative management of stab wounds to the posterior abdomen is safe: the Pietermaritzburg experience.

PubMed

Kong, Victor; Oosthuizen, George; Sartorius, Benn; Clarke, Damian

2015-09-01

The selective non-operative management (SNOM) of stab injuries of the anterior abdomen is well established, but its application to the posterior abdomen remains controversial. A retrospective review of 1013 patients was undertaken at a major trauma service in South Africa over a five-year period. Ninety per cent of patients were males, and the mean age was 25 years. The mean time from injury to presentation was 4h and 73% of all injuries were inflicted by knives. A total of 9% (93) of patients required a laparotomy [Group A] and 82% (833) were successfully observed without the need for operative intervention [Group B]. CT imaging was performed on 52 patients (5%) who had haematuria [Group C], 25 (3%) who had neurological deficits [Group D], and 10 (1%) with retained weapon injuries [Group E]. The accuracy of physical examination for identifying the presence of organ injury was 88%. All observed patients who required laparotomy declared themselves within 24h. There were no mortalities as direct result of our current management protocol. Selective management based on active clinical observation and serial physical examination is safe, and when coupled with the judicious use of advanced imaging, is a prudent and reliable approach in a resource constrained environment. Copyright © 2015 Elsevier Ltd. All rights reserved.

Ensuring a Safe Technological Revolution

DTIC Science & Technology

2016-12-01

Defense AT&L: November-December 2016 14 Ensuring a Safe Technological Revolution William E. Frazier, Ph.D. n Elizabeth L. McMichael n Jennifer...for 5 years, working on nonferrous welding and AM and has an M.S. in Mechanical Engineering from the University of Maryland, Baltimore County. I n...has acceptable proper- ties. A “certified” part can perform properly in its operating environment . The conventional qualification/certification

UTM Safely Enabling UAS Operations in Low-Altitude Airspace

NASA Technical Reports Server (NTRS)

Kopardekar, Parimal

2017-01-01

Conduct research, development and testing to identify airspace operations requirements to enable large-scale visual and beyond visual line of sight UAS operations in the low-altitude airspace. Use build-a-little-test-a-little strategy remote areas to urban areas Low density: No traffic management required but understanding of airspace constraints. Cooperative traffic management: Understanding of airspace constraints and other operations. Manned and unmanned traffic management: Scalable and heterogeneous operations. UTM construct consistent with FAAs risk-based strategy. UTM research platform is used for simulations and tests. UTM offers path towards scalability.

UTM Safely Enabling UAS Operations in Low-Altitude Airspace

NASA Technical Reports Server (NTRS)

Kopardekar, Parimal H.

2016-01-01

Conduct research, development and testing to identify airspace operations requirements to enable large-scale visual and beyond visual line of sight UAS operations in the low-altitude airspace. Use build-a-little-test-a-little strategy remote areas to urban areas Low density: No traffic management required but understanding of airspace constraints. Cooperative traffic management: Understanding of airspace constraints and other operations. Manned and unmanned traffic management: Scalable and heterogeneous operations. UTM construct consistent with FAAs risk-based strategy. UTM research platform is used for simulations and tests. UTM offers path towards scalability.

Fracture resistance of glazed, full-contour ZLS incisor crowns.

PubMed

Schwindling, Franz Sebastian; Rues, Stefan; Schmitter, Marc

2017-07-01

To compare the failure behaviour of zirconia-reinforced lithium silicate (Celtra Duo, DeguDent) with that of lithium disilicate (IPS e.max CAD, Ivoclar Vivadent) and feldspar (Mark II, VITA) ceramics. Three groups of sixteen glazed maxillary incisor crowns were produced. The inner surfaces of the crowns were etched, then luted to metal dies with self-adhesive cement. Single load-to-failure tests were performed before and after thermo-mechanical ageing. To simulate clinical conditions, the specimens were thermocycled (10,000 cycles between 6.5°C and 60°C) and underwent chewing simulation (1,200,000 cycles, F max =86N). Statistical analyses were performed by use of non-parametric Kruskal-Wallis and Mann-Whitney U-tests. Before ageing, all the monolithic incisor crowns fractured at test forces >285N. Mean fracture loads were highest for zirconia-reinforced lithium silicate (725N, SD 162N), slightly lower for lithium disilicate (701N, SD 276N), and lowest for feldspar (554N, SD 190N). The differences between the results were not statistically significant. After ageing, fracture resistance decreased for all materials except zirconia-reinforced lithium silicate. Mean fracture loads were highest for zirconia-reinforced lithium silicate (766N, SD 98N) and significantly lower for both lithium disilicate (485N, SD 64N) and feldspar (372N, SD 116N). Monolithic restorations fabricated from zirconia-reinforced lithium silicate retain high fracture resistance after extensive thermo-mechanical ageing. This preclinical study suggests that cohesive failures of monolithic anterior crowns produced of these ceramics will not be a major problem in dental practice. Copyright © 2017 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

Inherently safe in situ uranium recovery

DOEpatents

Krumhansl, James L; Brady, Patrick V

2014-04-29

An in situ recovery of uranium operation involves circulating reactive fluids through an underground uranium deposit. These fluids contain chemicals that dissolve the uranium ore. Uranium is recovered from the fluids after they are pumped back to the surface. Chemicals used to accomplish this include complexing agents that are organic, readily degradable, and/or have a predictable lifetime in an aquifer. Efficiency is increased through development of organic agents targeted to complexing tetravalent uranium rather than hexavalent uranium. The operation provides for in situ immobilization of some oxy-anion pollutants under oxidizing conditions as well as reducing conditions. The operation also artificially reestablishes reducing conditions on the aquifer after uranium recovery is completed. With the ability to have the impacted aquifer reliably remediated, the uranium recovery operation can be considered inherently safe.

The Safe Zone Range for Cup Anteversion Is Narrower Than for Inclination in THA.

PubMed

Murphy, William S; Yun, Ho Hyun; Hayden, Brett; Kowal, Jens H; Murphy, Stephen B

2018-02-01

Cup malposition is a common cause of impingement, limitation of ROM, acceleration of bearing wear, liner fracture, and instability in THA. Previous studies of the safe zone based on plain radiographs have limitations inherent to measuring angles from two-dimensional projections. The current study uses CT to measure component position in stable and unstable hips to assess the presence of a safe zone for cup position in THA. (1) Does acetabular component orientation, when measured on CT, differ in stable components and those revised for recurrent instability? (2) Do CT data support historic safe zone definitions for component orientation in THA? We identified 34 hips that had undergone revision of the acetabulum for recurrent instability that also had a CT scan of the pelvis between August 2003 and February 2017. We also identified 175 patients with stable hip replacements who also had a CT study for preoperative planning and intraoperative navigation of the contralateral side. For each CT study, one observer analyzed major factors including acetabular orientation, femoral anteversion, combined anteversion (the sum of femoral and anatomic anteversion), pelvic tilt, total offset difference, head diameter, age, sex, and body mass index. These measures were then compared among stable hips, hips with cup revision for anterior instability, and hips with cup revision for posterior instability. We used a clinically relevant measurement of operative anteversion and inclination as opposed to the historic use of radiographic anteversion and inclination. The percentage of unstable hips in the historic Lewinnek safe zone was calculated, and a new safe zone was proposed based on an area with no unstable hips. Anteriorly unstable hips compared with stable hips had higher operative anteversion of the cup (44° ± 12° versus 31° ± 11°, respectively; mean difference, 13°; 95% confidence interval [CI], 5°-21°; p = 0.003), tilt-adjusted operative anteversion of the cup (40° �

Environmentally safe fluids for hydraulics used in civil engineering

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wirzberger, E.; Rexroth, M.

1995-12-31

The majority of hydraulic units used in civil engineering are operated with pressure fluids based on mineral oil. Most civil engineering projects are installed near or immediately next to bodies of water, therefore, any leakage signifies danger for the environment. We try to avert this danger with increasingly safe hydraulic drives. However, growing environmental awareness and stricter laws are demanding more and more environmentally safe hydraulic fluids. Today, the manufacturers of fluids and hydraulic drives have to accept this challenge. What exactly is an environmentally safe hydraulic fluid? The major objectives are: (1) they have to be biodegradable, (2) nomore » fish toxicity, (3) no water pollution, and (4) food compatibility.« less

The End-To-End Safety Verification Process Implemented to Ensure Safe Operations of the Columbus Research Module

NASA Astrophysics Data System (ADS)

Arndt, J.; Kreimer, J.

2010-09-01

The European Space Laboratory COLUMBUS was launched in February 2008 with NASA Space Shuttle Atlantis. Since successful docking and activation this manned laboratory forms part of the International Space Station(ISS). Depending on the objectives of the Mission Increments the on-orbit configuration of the COLUMBUS Module varies with each increment. This paper describes the end-to-end verification which has been implemented to ensure safe operations under the condition of a changing on-orbit configuration. That verification process has to cover not only the configuration changes as foreseen by the Mission Increment planning but also those configuration changes on short notice which become necessary due to near real-time requests initiated by crew or Flight Control, and changes - most challenging since unpredictable - due to on-orbit anomalies. Subject of the safety verification is on one hand the on orbit configuration itself including the hardware and software products, on the other hand the related Ground facilities needed for commanding of and communication to the on-orbit System. But also the operational products, e.g. the procedures prepared for crew and ground control in accordance to increment planning, are subject of the overall safety verification. In order to analyse the on-orbit configuration for potential hazards and to verify the implementation of the related Safety required hazard controls, a hierarchical approach is applied. The key element of the analytical safety integration of the whole COLUMBUS Payload Complement including hardware owned by International Partners is the Integrated Experiment Hazard Assessment(IEHA). The IEHA especially identifies those hazardous scenarios which could potentially arise through physical and operational interaction of experiments. A major challenge is the implementation of a Safety process which owns quite some rigidity in order to provide reliable verification of on-board Safety and which likewise provides enough

Cool and Safe: Multiplicity in Safe Innovation at Unilever

ERIC Educational Resources Information Center

Penders, Bart

2011-01-01

This article presents the making of a safe innovation: the application of ice structuring protein (ISP) in edible ices. It argues that safety is not the absence of risk but is an active accomplishment; innovations are not "made safe afterward" but "safe innovations are made". Furthermore, there are multiple safeties to be accomplished in the…

[Safe school].

PubMed

Liberal, Edson Ferreira; Aires, Roberto Tschoepke; Aires, Mariana Tschoepke; Osório, Ana Carla de Albuquerque

2005-11-01

To review the strategies to make school a safe environment. The paper first addresses the social context of accidents and violence in the school environment, and makes recommendations, based on the literature data, for the implementation of safe schools. Articles published between 1993 and 2005 in the MEDLINE database. Brazilian epidemiological and literature data have also been searched. There is growing evidence that intervention has multiple components, focusing on health education practices, with the participation of the whole community. The aim of those interventions is to help students and community members to adopt healthy and safe behaviors. Schools are taking on an increasing role in health promotion, disease prevention, and injury prevention. In the context of prevention of external causes of morbidity and mortality, it is important to recognize a risky environment, places, and risk behaviors as favorable to injury and violence, as well as the concept of accident as something one can avoid. Implementation of safe schools represents a promising new direction for school-based preventive work. It is important to note that a safe school should intervene not only in its physical structure, but it should also make it as safe as possible by gathering the school community through health education, and mainly encouraging healthy behavior.

An Experimental Study of the Aerodynamics of a Swept and Unswept Semispan Wing with a Simulated Glaze Ice Accretion

NASA Technical Reports Server (NTRS)

Bragg, Michael B.

1994-01-01

Two semispan wings, one with a rectangular planform and one with 30 degrees of leading edge sweep were tested. Both had a NACA 0012 airfoil section, and both were tested clean and with simulated glaze ice shapes on their leading edges. Several surface roughness were tested. Each model geometry is documented and each surface roughness is explained. Aerodynamic performance of the wing in the form of sectional lift and integrated three-dimensional lift is documented through pressure measurements obtained from rows of surface pressure taps placed at five span locations on the wing. For the rectangular wing, sectional drag near the midspan is obtained from wake total pressure profiles. The data is presented in tabular and graphical form and is also available on computer disk.

A Safe Cooperative Framework for Atmospheric Science Missions with Multiple Heterogeneous UAS using Piecewise Bezier Curves

NASA Technical Reports Server (NTRS)

Mehdi, S. Bilal; Puig-Navarro, Javier; Choe, Ronald; Cichella, Venanzio; Hovakimyan, Naira; Chandarana, Meghan; Trujillo, Anna; Rothhaar, Paul M.; Tran, Loc; Neilan, James H.;

Investigation of safe-life fail-safe criteria for the space shuttle

NASA Technical Reports Server (NTRS)

1972-01-01

An investigation was made to determine the effects of a safe-life design approach and a fail-safe design approach on the space shuttle booster vehicle structure, and to recommend any changes to the structural design criteria. Two configurations of the booster vehicle were considered, one incorporating a delta wing (B-9U configuration) and the other a swept wing (B-16B configuration). Several major structural components of the booster were studied to determine the fatigue life, safe-life, and fail-safe capabilities of the baseline design. Each component was investigated to determine the practicability of applying a safe-life or fail-safe design philosophy, the changes such design approaches might require, and the impact of these changes on weight, cost, development plans, and performance.

The Safe Yield and Climatic Variability: Implications for Groundwater Management.

PubMed

Loáiciga, Hugo A

2017-05-01

Methods for calculating the safe yield are evaluated in this paper using a high-quality and long historical data set of groundwater recharge, discharge, extraction, and precipitation in a karst aquifer. Consideration is given to the role that climatic variability has on the determination of a climatically representative period with which to evaluate the safe yield. The methods employed to estimate the safe yield are consistent with its definition as a long-term average extraction rate that avoids adverse impacts on groundwater. The safe yield is a useful baseline for groundwater planning; yet, it is herein shown that it is not an operational rule that works well under all climatic conditions. This paper shows that due to the nature of dynamic groundwater processes it may be most appropriate to use an adaptive groundwater management strategy that links groundwater extraction rates to groundwater discharge rates, thus achieving a safe yield that represents an estimated long-term sustainable yield. An example of the calculation of the safe yield of the Edwards Aquifer (Texas) demonstrates that it is about one-half of the average annual recharge. © 2016, National Ground Water Association.

Safe Zones: Creating LGBT Safe Space Ally Programs

ERIC Educational Resources Information Center

Poynter, Kerry John; Tubbs, Nancy Jean

2008-01-01

This article discusses model LGBT Safe Space Ally programs. These programs, often called "Safe Zones," include self selected students, faculty, and employees who publicly show support by displaying stickers, signs, and other identifiable items. Issues covered in the article include history, development, training, membership, assessment, and…

Exploring varieties of knowledge in safe work practices - an ethnographic study of surgical teams

PubMed Central

2011-01-01

Background Within existing research in health and medicine, the nature of knowledge on how teams conduct safe work practices has yet to be properly explored. Methods We address this concern by exploring the varieties in which knowledge is expressed during interdisciplinary surgical operations. Specifically, the study was conducted in a surgical section of a Norwegian regional general hospital, between January and April of 2010, by means of an ethnographic design combining detailed non-participant observations, conversations and semi-structured interviews. Results Based on an analysis of the gathered data, we identify three particular themes in how knowledge is expressed by operating room personnel: (i) the ability and variety individuals demonstrate in handling multiple sources of information, before reaching a particular decision, (ii) the variety of ways awareness or anticipation of future events is expressed, and (iii) the different ways sudden and unexpected situations are handled by the individual team members. Conclusions We conclude that these facets of knowledge bring different insights into how safe work practices are achieved at an individual and team level in surgical operations, thus adding to the existing understanding of the nature of knowledge in safe work practices in surgical operations. Future research should focus on exploring and documenting the relationships between various elements of knowledge and safe work practices, in different surgical settings and countries. PMID:21914183

40 CFR 63.11435 - Am I subject to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

...) National Emission Standards for Hazardous Air Pollutants for Clay Ceramics Manufacturing Area Sources... if you own or operate a clay ceramics manufacturing facility (as defined in § 63.11444), with an atomized glaze spray booth or kiln that fires glazed ceramic ware, that processes more than 45 megagrams...

Filament-strung stand-off elements for maintaining pane separation in vacuum insulating glazing units

DOEpatents

Bettger, Kenneth J; Stark, David H

2013-08-20

A vacuum insulating glazing unit (VIGU) comprises first and second panes of transparent material, first and second anchors, a plurality of filaments, a plurality of stand-off elements, and seals. The first and second panes of transparent material have edges and inner and outer faces, are disposed with their inner faces substantially opposing one another, and are separated by a gap having a predetermined height. The first and second anchors are disposed at opposite edges of one pane of the VIGU. Each filament is attached at one end to the first anchor and at the other end to the second anchor, and the filaments are collectively disposed between the panes substantially parallel to one another. The stand-off elements are affixed to each filament at predetermined positions along the filament, and have a height substantially equal to the predetermined height of the gap such that the each stand-off element touches the inner surfaces of both panes. The seals are disposed about the edges of the panes, enclosing the stand-off elements within a volume between the panes from which the atmosphere may be evacuated to form a partial vacuum.

29 CFR 1918.86 - Roll-on roll-off (Ro-Ro) operations (see also § 1918.2, Ro-Ro operations, and § 1918.25).

Code of Federal Regulations, 2011 CFR

2011-07-01

... simultaneous use of the ramp by vehicles and pedestrians. (d) Ramp maintenance. Ramps shall be properly... ramp inclines safely. (j) Safe speeds. Power driven vehicles used in Ro-Ro operations shall be operated at speeds that are safe for prevailing conditions. (k) Ventilation. Internal combustion engine-driven...

Safe pill-dispensing.

PubMed

Testa, Massimiliano; Pollard, John

2007-01-01

Each patient is supplied with a smart-card containing a Radio Frequency IDentification (RFID) chip storing a unique identification code. The patient places the Smart-card on a pill-dispenser unit containing an RFID reader. The RFID chip is read and the code sent to a Base-station via a wireless Bluetooth link. A database containing both patient details and treatment information is queried at the Base-station using the RFID as the search key. The patient's treatment data (i.e., drug names, quantities, time, etc.) are retrieved and sent back to the pill-dispenser unit via Bluetooth. Appropriate quantities of the required medications are automatically dispensed, unless the patient has already taken his/her daily dose. Safe, confidential communication and operation is ensured.

Improved Quick Disconnect (QD) Interface Through Fail Safe Parts Identification

NASA Technical Reports Server (NTRS)

Blanch-Payne, Evelyn

2001-01-01

An extensive review of existing Quick Disconnects (QDs) mating and demating operations was performed to determine which shuttle part interface identifications and procedures contribute to human factor errors. The research methods used consisted of interviews with engineers and technicians, examination of incident reports, critiques of video and audio tapes of QD operations, and attendance of a Hyper QD operational course. The data strongly suggests that there are inherit human factor errors involved in QD operations. To promote fail-safe operations, QD interface problem areas and recommendations were outlined and reviewed. It is suggested that dialogue, investigations and recommendations continue.

A discussion on turbine design for safe operation

NASA Astrophysics Data System (ADS)

Brekke, H.

2012-11-01

The paper gives a brief description of the hydraulic design of Francis and Pelton runners. The dynamic behaviour at part load has been a major problem for low head and medium head Francis turbines. The main reason for this has been inter blade separation and unstable swirl flow in the draft tube. A description is given on the hydraulic design of X-BLADE runners to obtain stable operation on the whole range of operation by reducing the cross flow. A classical theoretical analysis is also given on the dynamic hydraulic load on Pelton buckets. Several CFD analyses of this non stationary flow have been presented during the last decade, but the velocity distribution in the jets have not been correct. Experimental research work is presented on the complexity of this problem.

Laparoscopic appendicectomy: safe and useful for training.

PubMed Central

Duff, S. E.; Dixon, A. R.

2000-01-01

Debate exists about the benefits of laparoscopic appendicectomy when compared to a conventional open procedure. The majority of appendices are removed by the open route in the UK. We report a series of 132 cases of suspected appendicitis managed laparoscopically: 112 (85%) of the patients had acute appendicitis, the remaining 20 (15%) had non-appendiceal pathology. The median operative time was 30 min and there were no conversions to an open operative procedure. The median postoperative stay was two days. Complications were seen in two patients. The published evidence comparing laparoscopic and open appendicectomy is contradictory. Our series shows that laparoscopic appendicectomy is a safe procedure with low morbidity; it is also an excellent training tool in laparoscopic technique and, with sufficient experience, takes no longer than an open procedure. Negative appendicocecotomies are most common in women of fertile age and can be associated with significant morbidity; therefore, laparoscopy should be used to make the diagnosis and, if appendicitis is the cause, the appendix could safely be removed laparoscopically. However, the choice between open and laparoscopic procedure is a subjective decision for the patient and their surgeon. Laparoscopic appendicectomy cannot be regarded as the gold standard. PMID:11103154

46 CFR 114.600 - Incorporation by reference.

Code of Federal Regulations, 2011 CFR

2011-10-01

... supplement—Safety Glazing Materials For Glazing Motor Vehicles Operating on Land Highways 116.1030 American... Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position... Burning Characteristics of Building Materials 116.405; 116.422; 116.423 ASTM E 648-97, Standard Test...

78 FR 41991 - Petition for Waiver of Compliance

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-12

... not have window glazing meeting the requirements of 49 CFR 223.15. This car is interchanged with... environment of the cars. Operation of this private passenger car has been injury-free as related to window... Adams & Westlake 64 sash, double-glazed, 30'' x 42'' side windows with a mixture of unmarked...

[Use of lead-glazed ceramic as a source of exposure in children of marginalized indigenous zones of Oaxaca, Mexico].

PubMed

Terrazas-Meraz, María Alejandra; Hernández-Cadena, Leticia; Rueda-Hernández, Gabriela E; Romano-Riquer, Sonia Patricia; Shamah-Levy, Teresa; Villalpando-Hernández, Salvador; Téllez-Rojo Solís, Martha Ma; Hernández-Ávila, Mauricio

2015-01-01

To find out whether the use of lead-glazed ceramic (LGC) is associated with blood lead levels in indigenous schoolchildren from Oaxaca, México. We evaluated LGC use at home as a primary source of lead exposure in 387 indigenous schoolchildren in Oaxaca in May 2001. We found an adjusted difference of 3.9μg/dl (p<0.01) in blood lead levels (BLL) among children reporting to use (82%) LGC at home vs those who didn't. BL levels greater or equal than 10 and 20 μg/dl were observed in 60 and 27% of children, respectively. Lead poisoning from LGC use could remain a concern for public health in Mexico, where there is a need to provide care and further study to verify its effect on BLL.

Dispersion stability of a ceramic glaze achieved through ionic surfactant adsorption.

PubMed

Panya, Preecha; Arquero, Orn-anong; Franks, George V; Wanless, Erica J

2004-11-01

The adsorption of cetylpyridinium chloride (CPC) and sodium dodecylbenzenesulfonate (SDBS) onto a ceramic glaze mixture composed of limestone, feldspar, quartz, and kaolin has been investigated. Both adsorption isotherms and the average particle zeta potential have been studied in order to understand the suspension stability as a function of pH, ionic strength, and surfactant concentration. The adsorption of small amounts of cationic CPC onto the primarily negatively charged surfaces of the particles at pH 7 and 9 results in strong attraction and flocculation due to hydrophobic interactions. At higher surfactant concentrations a zeta potential of more than +60 mV results from the bilayered adsorbed surfactant, providing stability at salt concentrations < or = 0.01 M. At 0.1 M salt poor stability results despite substantial zeta potential values. Three mechanisms for SDBS adsorption have been identified. When anionic SDBS monomers either adsorb by electrostatic interactions with the few positive surface sites at high pH or adsorb onto like charged negative surface sites due to dispersion or hydrophobic interactions, the magnitude of the negative zeta potential increases slightly. At pH 9 this increase is enough to promote stability with an average zeta potential of more than -55 mV, whereas at pH 7 the zeta potential is lower at about -45 mV. The stability of suspensions at pH 7 is additionally due to steric repulsion caused by the adsorption of thick layers of neutrally charged Ca(DBS)2 complexes created when the surfactant interacts with dissolved calcium ions from the calcium carbonate component.

Safe Schools, Safe Communities.

ERIC Educational Resources Information Center

Lewis, Julie E.; Pickett, Dean; Pulliam, Janet L.; Schwartz, Richard A.; St. Germaine, Anne-Marie; Underwood, Julie; Worona, Jay

Schools must work together with agencies, groups, and individuals to eliminate the forces leading children to violence. Chapter 1, "School Safety: Working Together to Keep Schools Safe," stresses the importance of community collaboration in violence prevention. Effective prevention requires sharing information about students, consistent…

Unsupervised laparoscopic appendicectomy by surgical trainees is safe and time-effective.

PubMed

Wong, Kenneth; Duncan, Tristram; Pearson, Andrew

2007-07-01

Open appendicectomy is the traditional standard treatment for appendicitis. Laparoscopic appendicectomy is perceived as a procedure with greater potential for complications and longer operative times. This paper examines the hypothesis that unsupervised laparoscopic appendicectomy by surgical trainees is a safe and time-effective valid alternative. Medical records, operating theatre records and histopathology reports of all patients undergoing laparoscopic and open appendicectomy over a 15-month period in two hospitals within an area health service were retrospectively reviewed. Data were analysed to compare patient features, pathology findings, operative times, complications, readmissions and mortality between laparoscopic and open groups and between unsupervised surgical trainee operators versus consultant surgeon operators. A total of 143 laparoscopic and 222 open appendicectomies were reviewed. Unsupervised trainees performed 64% of the laparoscopic appendicectomies and 55% of the open appendicectomies. There were no significant differences in complication rates, readmissions, mortality and length of stay between laparoscopic and open appendicectomy groups or between trainee and consultant surgeon operators. Conversion rates (laparoscopic to open approach) were similar for trainees and consultants. Unsupervised senior surgical trainees did not take significantly longer to perform laparoscopic appendicectomy when compared to unsupervised trainee-performed open appendicectomy. Unsupervised laparoscopic appendicectomy by surgical trainees is safe and time-effective.

Safe start up of a green field ethylene plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stark, C.L.; Moore, J.R.

1994-12-31

In 1988, Westlake Petrochemicals Corporation elected to construct and operate a facility for producing 1 billion pounds per year of ethylene. The project was to be accomplished where there was no established corporate environment for ethylene production and the facility was to be located at a green field site. The establishment and empowerment of the personnel organization would therefore, also be green field in nature. With the meager beginnings of but one employee, the project team was assembled; chartered to accomplish their assignment safely and proficiently. Thirty-three months later, the unit was safely put on line and has been operatingmore » without injury for over 2-1/2 years. The facility accomplished design level operations within four months of start-up and successfully completed its performance test run the following month. A real credit to the personnel. How has this been accomplished? A collective and individual, intense focus on safety. The paper describes how this was accomplished.« less

14 CFR 121.553 - Restriction or suspension of operation: Supplemental operations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Restriction or suspension of operation: Supplemental operations. 121.553 Section 121.553 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... conditions, that are a hazard to safe operations, the certificate holder or pilot in command, as the case may...

Safe corridors for K-wiring in phalangeal fractures.

PubMed

Rex, C; Vignesh, R; Javed, M; Balaji, Subba Chandra; Premanand, C; Zakki, Syed Ashfaque

2015-01-01

Unstable phalangeal fractures are commonly treated with K-wire fixation. Operative fixation must be used judiciously and with the expectation that the ultimate outcome should be better than the outcome after nonoperative management. It is necessary to achieve a stable fracture fixation and early mobilization. In order to achieve this goal, one should closely understand the safe portals/corridors in hand for K-wire entry for fractures of the phalanges. Safe corridors were defined and tested using a pilot cadaveric and a clinical case study by assessing the outcome. In our prospective case series, 50 patients with 64 phalangeal fractures were treated with closed reduction and K-wires were inserted through safe portals identified by a pilot cadaveric study. On table active finger movement test was done and the results were analyed using radiology, disabilities of the arm, shoulder, and hand (DASH) score and total active motion (TAM). In our study, little finger (n = 28) was the most commonly involved digit. In fracture pattern, transverse (n = 20) and spiral (n = 20) types were common. Proximal phalanx (n = 38) was commonly involved and the common site being the base of the phalanx (n = 28). 47 (95%) patients had excellent TAM and the mean postoperative DASH score was 58.05. All patients achieved excellent and good scores proving the importance of the safe corridor concept. K-wiring through the safe corridor has proved to yield the best clinical results because of least tethering of soft tissues as evidenced by performing "on-table active finger movement test" at the time of surgery. We strongly recommend K-wiring through safe portals in all phalangeal fractures.

14 CFR 121.551 - Restriction or suspension of operation: Domestic and flag operations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Restriction or suspension of operation: Domestic and flag operations. 121.551 Section 121.551 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... conditions, that are a hazard to safe operations, it shall restrict or suspend operations until those...

14 CFR 121.551 - Restriction or suspension of operation: Domestic and flag operations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Restriction or suspension of operation: Domestic and flag operations. 121.551 Section 121.551 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... conditions, that are a hazard to safe operations, it shall restrict or suspend operations until those...

Safe sex self-efficacy and safe sex practice in a Southern United States College

PubMed Central

Addoh, Ovuokerie; Sng, Eveleen; Loprinzi, Paul D.

2017-01-01

Background: The purpose of this study was to assess the association between safe sex self-efficacy and safe-sex practice in a Southern college setting. Methods: Multivariable logistic regression models were used to examine the association between safe sex self-efficacy in four domains (mechanics, partner disapproval, assertiveness, intoxicants) and safe sex practice (outcome variable). Results: For every 1-unit increase in the composite condom use self-efficacy score, there was an 8% increase in the odds of being beyond the median safe-sex practice score (odds ration [OR]: 1.08, 95% CI: 1.02-1.15). Additionally, for every 1-unit increase in intoxicants self-efficacy score, there was a 31% increase in the odds of being beyond the median safe-sex practice score (OR: 1.31, 95% CI: 1.08-1.58). Conclusion: A greater degree of safe-sex self-efficacy is associated with increased odds of safe-sex practice. These findings are informative for the development of targeted approaches to foster safe-sex behavior in Southern US colleges. PMID:28326287

Inherently Safe and Long-Life Fission Power System for Lunar Outposts

NASA Astrophysics Data System (ADS)

Schriener, T. M.; El-Genk, Mohamed S.

Power requirements for future lunar outposts, of 10's to 100's kWe, can be fulfilled using nuclear reactor power systems. In addition to the long life and operation reliability, safety is paramount in all phases, including fabrication and assembly, launch, emplacement below grade on the lunar surface, operation, post-operation decay heat removal and long-term storage and eventual retrieval. This paper introduces the Solid Core-Sectored Compact Reactor (SC-SCoRe) and power system with static components and no single point failures. They ensure reliable continuous operation for ~21 years and fulfill the safety requirements. The SC-SCoRe nominally generates 1.0 MWth at liquid NaK-56 coolant inlet and exit temperatures of 850 K and 900 K and the power system provides 38 kWe at high DC voltage using SiGe thermoelectric (TE) conversion assemblies. In case of a loss of coolant or cooling in a reactor core sector, the power system continues to operate; generating ~4 kWe to the outpost for emergency life support needs. The post-operation storage of the reactor below grade on the lunar surface is a safe and practical choice. The total radioactivity in the reactor drops from ~1 million Ci, immediately at shutdown, to below 164 Ci after 300 years of storage. At such time, the reactor is retrieved safely with no contamination or environmental concerns.

DroidSafe

DTIC Science & Technology

2016-12-01

branches of our work . 3.1 Understanding Sensitive API Call and API Information Usage Android applications are written in a type- safe language (Java...directly invoke resolved targets. Because DroidSafe works with a comprehensive model of the Android environment , it supports precise resolution of...STATEMENT. FOR THE CHIEF ENGINEER: / S / / S / MARK K. WILLIAMS WARREN H. DEBANY, JR. Work Unit Manager

A Safe Ride to School; A Safe Ride Home.

ERIC Educational Resources Information Center

Illinois State Board of Education, Springfield.

Text and illustrations are used to teach safe school bus riding practices. The guide begins with instructions to parents or guardians to set a good example of safe behavior, and to help children learn safety rules and be on time. Instructions to children concern obeying the bus driver, boarding the bus, riding the bus, crossing the road, and using…

Safe Haven Configurations for Deep Space Transit Habitats

NASA Technical Reports Server (NTRS)

Smitherman, David; Polsgrove, Tara; Rowe, Justin; Simon, Matthew

2017-01-01

Throughout the human space flight program there have been instances where smoke, fire, and pressure loss have occurred onboard space vehicles, putting crews at risk for loss of mission and loss of life. In every instance the mission has been in Low-Earth-Orbit (LEO) with access to multiple volumes that could be used to quickly seal off the damaged module or escape vehicles for a quick return to Earth. For long duration space missions beyond LEO, including Mars transit missions of about 1000 days, the mass penalty for multiple volumes has been a concern as has operating in an environment where a quick return will not be possible. In 2016 a study was done to investigate a variety of dual pressure vessel configurations for habitats that could protect the crew from these hazards. It was found that for a modest increase in total mass it should be possible to provide significant protection for the crew. Several configurations were developed that either had a small safe haven to provide 30-days to recover, or a full duration safe haven using two equal size pressure vessel volumes. The 30-day safe haven was found to be the simplest, yielding the least total mass impact but still with some risk if recovery is not possible during that timeframe. The full duration safe haven was the most massive option but provided the most robust solution. This paper provides information on the various layouts considered in the study and provides a discussion of the findings for implementing a safe haven in future habitat designs.

Payload Instrument Design Rules for Safe and Efficient Flight Operations

NASA Astrophysics Data System (ADS)

Montagnon, E.; Ferri, P.

2004-04-01

Payload operations are often being neglected in favour of optimisation of scientific performance of the instrument design. This has major drawbacks in terms of cost, safety, efficiency of operations and finally science return. By taking operational aspects into account in the early phases of the instrument design, with a minimum more cultural than financial or technological additional effort, many problems can be avoided or minimized, with significant benefits to be gained in the mission execution phases. This paper presents possible improvements based on the use of the telemetry and telecommand packet standard, proper sharing of autonomy functions between instrument and platform, and enhanced interface documents.

Use Medicines Safely

MedlinePlus

... Medicines Safely Print This Topic En español Use Medicines Safely Browse Sections The Basics Overview Prescription Medicines ... Medicines 1 of 7 sections The Basics: Prescription Medicines There are different types of medicine. The 2 ...

Picture Me Safe

ERIC Educational Resources Information Center

Irvin, Daniel W.

1977-01-01

The validity of well-written articles can be destroyed by poor illustration, especially when the pictures show unsafe practices. The responsibility lies with the author to provide clear printable pictures showing safe working environments and safe practices. (Editor)

Advanced Technologies in Safe and Efficient Operating Rooms

DTIC Science & Technology

2007-02-01

facilities that deal with trauma. The resulting chaos can be overwhelming, even with some form of electronic health record ( EHR ) system (currently...computers which process this data to deliver more efficient health -related services. The EMR is an essential part of systems like the Traumapod [24...perioperative situational awareness system that captures and records data from various medical devices and provides an integrated display to allow the operating

Target Trailing With Safe Navigation With Colregs for Maritime Autonomous Surface Vehicles

NASA Technical Reports Server (NTRS)

Kuwata, Yoshiaki (Inventor); Aghazarian, Hrand (Inventor); Huntsberger, Terrance L. (Inventor); Howard, Andrew B. (Inventor); Wolf, Michael T. (Inventor); Zarzhitsky, Dimitri V. (Inventor)

2014-01-01

Systems and methods for operating autonomous waterborne vessels in a safe manner. The systems include hardware for identifying the locations and motions of other vessels, as well as the locations of stationary objects that represent navigation hazards. By applying a computational method that uses a maritime navigation algorithm for avoiding hazards and obeying COLREGS using Velocity Obstacles to the data obtained, the autonomous vessel computes a safe and effective path to be followed in order to accomplish a desired navigational end result, while operating in a manner so as to avoid hazards and to maintain compliance with standard navigational procedures defined by international agreement. The systems and methods have been successfully demonstrated on water with radar and stereo cameras as the perception sensors, and integrated with a higher level planner for trailing a maneuvering target.

Safe Haven Configurations for Deep Space Transit Habitats

NASA Technical Reports Server (NTRS)

Smitherman, David; Polsgrove, Tara; Rowe, Justin; Simon, Matthew

2017-01-01

Throughout the human space flight program there have been instances where systems failures resulting in smoke, fire, and pressure loss have occurred onboard space vehicles, putting crews at risk for loss of mission and loss of life. In most instances the missions have been in Low-Earth-Orbit (LEO) or Earth-Moon vicinity, with access to multiple volumes that could be used to quickly seal off the damaged module or access escape vehicles for return to Earth. For long duration missions beyond LEO, including Mars transit missions of about 1100 days, the mass penalty for multiple volumes and operating in an environment where a quick return will not be possible have been concerns. In 2016, a study was done to investigate a variety of dual pressure vessel configurations for habitats that could protect the crew from these hazards. It was found that with a modest increase in total mass it should be possible to provide significant protection for the crew. Several configurations were considered that either had a small safe haven to provide 30-days to recover, or a full duration safe haven using two equal size pressure vessel volumes. The 30-day safe haven was found to be the simplest, yielding the least total mass impact but still with some risk if recovery is not possible during that timeframe. The full duration safe haven was the most massive option but provided the most robust solution. This paper provides information on the various layouts developed during the study and provides a discussion of the findings for implementing a safe haven in future habitat designs.

Safe Schools/Safe Communities: A Directory of Resources for Pennsylvania.

ERIC Educational Resources Information Center

Pennsylvania State Dept. of Education, Harrisburg.

This document contains a directory of resources available in Pennsylvania to help achieve the goal of safe schools. Following a copy of the Safe Schools Act of 1993, nine sections list agencies that provide services and products under the headings of: conflict resolution/mediation, gangs, suicide, crisis response, family violence, diversity,…

Lessons Learned from Safe Kids/Safe Streets. Juvenile Justice Bulletin

ERIC Educational Resources Information Center

Cronin, Roberta; Gragg, Frances; Schultz, Dana; Eisen, Karla

2006-01-01

This bulletin reports results from an evaluation of six sites of the Safe Kids/Safe Streets (SK/SS) program, which applies a comprehensive, collaborative approach to the child maltreatment field. The bulletin provides insights into collaboration building, systems reform, service options, and other strategies. Among the findings were that the SK/SS…

76 FR 12719 - Safe Schools/Healthy Students Program; Office of Safe and Drug-Free Schools; Safe Schools/Healthy...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-08

... official version of this document is the document published in the Federal Register. Free Internet access... DEPARTMENT OF EDUCATION Safe Schools/Healthy Students Program; Office of Safe and Drug- Free... telecommunications device for the deaf (TDD), call the Federal Relay Service (FRS), toll free, at 1-800-877-8339...

A comparison between the shear bond strength of brackets bonded to glazed and deglazed porcelain surfaces with resin-reinforced glass-ionomer cement and a bis-GMA resin adhesive.

PubMed

Lifshitz, Abraham B; Cárdenas, Marianela

2006-01-01

This study compared the shear bond strength of a light-cure resin-reinforced glass-ionomer cement with a bis-GMA light-cure resin system in the bonding of stainless steel brackets to glazed and deglazed porcelain surfaces. Porcelain surfaces were divided into 4 groups: group 1, deglazed porcelain surfaces with Transbond XT, group 2, glazed porcelain surfaces with Transbond XT; group 3, deglazed porcelain surfaces with Fuji Ortho LC; and group 4, porcelain surfaces with Fuji Ortho LC. Microetching with 50-microm aluminum oxide for 2 seconds at a distance of 5 mm deglazed the porcelain surfaces in groups 1 and 3. All brackets were bonded to the porcelain surfaces using the same procedure and light-cured for 40 seconds with a visible light. All samples were thermocycled between 5 degrees C and 55 degrees C for 300 cycles before testing for shear bond strength with a universal testing machine. The analysis of variance showed no significant difference (P < .05) among the 4 groups; ie, group 1, 10.12 MPa; group 2, 7.00 MPa; group 3, 6.78 MPa; and group 4, 11.15 MPa. The F test also failed to demonstrate any statistical difference among the groups. Conditioning the porcelain surfaces with 37% phosphoric acid immediately followed by a nonhydrolyzed silane coupling agent resulted in clinically adequate bond strength when using either a composite resin or a resin-reinforced glass-ionomer cement. Microetching of these porcelain surfaces apparently offers no bonding advantage.

Safe syringe disposal is related to safe syringe access among HIV-positive injection drug users.

PubMed

Coffin, Phillip O; Latka, Mary H; Latkin, Carl; Wu, Yingfeng; Purcell, David W; Metsch, Lisa; Gomez, Cynthia; Gourevitch, Marc N

2007-09-01

We evaluated the effect of syringe acquisition on syringe disposal among HIV-positive injection drug users (IDUs) in Baltimore, New York City, and San Francisco (N = 680; mean age 42 years, 62% male, 59% African-American, 21% Hispanic, 12% White). Independent predictors of safe disposal were acquiring syringes through a safe source and ever visiting a syringe exchange program. Weaker predictors included living in San Francisco, living in the area longer, less frequent binge drinking, injecting with an HIV+ partner, peer norms supporting safe injection, and self-empowerment. Independent predictors of safe "handling"-both acquiring and disposing of syringes safely-also included being from New York and being older. HIV-positive IDUs who obtain syringes from a safe source are more likely to safely dispose; peer norms contribute to both acquisition and disposal. Interventions to improve disposal should include expanding sites of safe syringe acquisition while enhancing disposal messages, alternatives, and convenience.

Prioritizing essential surgery and safe anesthesia for the Post-2015 Development Agenda: operative capacities of 78 district hospitals in 7 low- and middle-income countries.

PubMed

LeBrun, Drake G; Chackungal, Smita; Chao, Tiffany E; Knowlton, Lisa M; Linden, Allison F; Notrica, Michelle R; Solis, Carolina V; McQueen, K A Kelly

2014-03-01

Surgery has been neglected in low- and middle-income countries for decades. It is vital that the Post-2015 Development Agenda reflect that surgery is an important part of a comprehensive global health care delivery model. We compare the operative capacities of multiple low- and middle-income countries and identify critical gaps in surgical infrastructure. The Harvard Humanitarian Initiative survey tool was used to assess the operative capacities of 78 government district hospitals in Bangladesh (n = 7), Bolivia (n = 11), Ethiopia (n = 6), Liberia (n = 11), Nicaragua (n = 10), Rwanda (n = 21), and Uganda (n = 12) from 2011 to 2012. Key outcome measures included infrastructure, equipment availability, physician and nonphysician surgical providers, operative volume, and pharmaceutical capacity. Seventy of 78 district hospitals performed operations. There was fewer than one surgeon or anesthesiologist per 100,000 catchment population in all countries except Bolivia. There were no physician anesthesiologists in any surveyed hospitals in Rwanda, Liberia, Uganda, or in the majority of hospitals in Ethiopia. Mean annual operations per hospital ranged from 374 in Nicaragua to 3,215 in Bangladesh. Emergency operations and obstetric operations constituted 57.5% and 40% of all operations performed, respectively. Availability of pulse oximetry, essential medicines, and key infrastructure (water, electricity, oxygen) varied widely between and within countries. The need for operative procedures is not being met by the limited operative capacity in numerous low- and middle-income countries. It is of paramount importance that this gap be addressed by prioritizing essential surgery and safe anesthesia in the Post-2015 Development Agenda. Copyright © 2014 Mosby, Inc. All rights reserved.

Advanced Technologies in Safe and Efficient Operating Rooms

DTIC Science & Technology

2006-02-01

in this report are those of the author( s ) and should not be construed as an official Department of the Army position, policy or decision unless so...information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THE ABOVE ADDRESS. 1. REPORT DATE 01-02...and Efficient Operating Rooms 5b. GRANT NUMBER DAMD17-03-2-0001 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR( S ) 5d. PROJECT NUMBER Adrian E. Park

Transmission electron microscopy for archaeo-materials research: Nanoparticles in glazes and red/yellow glass and inorganic pigments in painted context

NASA Astrophysics Data System (ADS)

Fredrickx, Peggy

2004-10-01

This dissertation addresses the application of Transmission Electron Microscopy (TEM) to historic objects, concentrating on colour-causing nanoparticles in vitreous materials and pigments with the focus on substrates in lake pigments used in thin glaze layers, and on manuscript illustrations. TEM is well suited for archaeometry: it gives chemical elemental information, imaging and diffraction information and the amount of material needed is minimal. Sample preparation techniques suitable for historic materials are discussed. Nanoparticles can be incorporated in glass through staining. Yellow coloured glass plates contain Ag particles. Baking temperatures and different Ag-salts determine the density of the nanoparticles. Dense layers cause more saturated colours. Red glass plates can be obtained by staining with Cu-salts. Metallic Cu particles have a diameter of about 24 nm. Comparison with XRF results suggests that often a combination of Cu and Ag was used for warmer colours. Red glass can be "flashed" to the substrate glass. Then, the colour is also caused by metallic Cu particles. The red layer often displays a band structure of stacked red and transparent bands. In the transparent bands, no nanoparticles have been found. In lustre-ware, Ag and metallic Cu occur. Their distribution throughout the material determines the colour of the fragment. In both there is a dense top layer with particles of sizes smaller than 15 nm. If this top layer consists of Ag particles, the resulting colour is golden. In one sample, under this top layer the amount of Cu particles increases. This underlying layer causes the colour to redden. Particles are mainly between 5 and 15 nm in diameter. Using reconstructions, it has been demonstrated that TEM can detect and identify a stacking of thin layers in parchment decorations. A pink powder sample from Pompeii consists of a basis of allophane type clay. The lake substrates consist of Al, O, S and their amorphous structure does not seem to

A Personnel Launch System for safe and efficient manned operations

NASA Astrophysics Data System (ADS)

Petro, Andrew J.; Andrews, Dana G.; Wetzel, Eric D.

1990-10-01

Several Conceptual designs for a simple, rugged Personnel Launch System (PLS) are presented. This system could transport people to and from Low Earth Orbit (LEO) starting in the late 1990's using a new modular Advanced Launch System (ALS) developed for the Space Exploration Initiative (SEI). The PLS is designed to be one element of a new space transportation architecture including heavy-lift cargo vehicles, lunar transfer vehicles, and multiple-role spcecraft such as the current Space Shuttle. The primary role of the PLS would be to deliver crews embarking on lunar or planetary missions to the Space Station, but it would also be used for earth-orbit sortie missions, space rescue missions, and some satellite servicing missions. The PLS design takes advantage of emerging electronic and structures technologies to offer a robust vehicle with autonomous operating and quick turnaround capabilities. Key features include an intact abort capability anywhere in the operating envelope, and elimination of all toxic propellants to streamline ground operations.

Critically safe volume vacuum pickup for use in wet or dry cleanup of radioactive enclosures

DOEpatents

Zeren, J.D.

1993-12-28

A physical compact vacuum pickup device of critically safe volume and geometric shape is provided for use in radioactive enclosures, such as a small glove box, to facilitate manual cleanup of either wet or dry radioactive material. The device is constructed and arranged so as to remain safe when filled to capacity with plutonium-239 oxide. Two fine mesh filter bags are supported on the exterior of a rigid fine mesh stainless steel cup. This assembly is sealed within, and spaced from, the interior walls of a stainless steel canister. An air inlet communicates with the interior of the canister. A modified conventional vacuum head is physically connected to, and associated with, the interior of the mesh cup. The volume of the canister, as defined by the space between the mesh cup and the interior walls of the canister, forms a critically safe volume and geometric shape for dry radioactive particles that are gathered within the canister. A critically safe liquid volume is maintained by operation of a suction terminating float valve, and/or by operation of redundant vacuum check/liquid drain valves and placement of the air inlet. 5 figures.

Critically safe volume vacuum pickup for use in wet or dry cleanup of radioactive enclosures

DOEpatents

Zeren, Joseph D.

1993-12-28

A physical compact vacuum pickup device of critically safe volume and geometric shape is provided for use in radioactive enclosures, such as a small glove box, to facilitate manual cleanup of either wet or dry radioactive material. The device is constructed and arranged so as to remain safe when filled to capacity with plutonium-239 oxide. Two fine mesh filter bags are supported on the exterior of a rigid fine mesh stainless steel cup. This assembly is sealed within, and spaced from, the interior walls of a stainless steel canister. An air inlet communicates with the interior of the canister. A modified conventional vacuum head is physically connected to, and associated with, the interior of the mesh cup. The volume of the canister, as defined by the space between the mesh cup and the interior walls of the canister, forms a critically safe volume and geometric shape for dry radioactive particles that are gathered within the canister. A critically safe liquid volume is maintained by operation of a suction terminating float valve, and/or by operation of redundant vacuum check/liquid drain valves and placement of the air inlet.

Safe Grid

NASA Technical Reports Server (NTRS)

Chow, Edward T.; Stewart, Helen; Korsmeyer, David (Technical Monitor)

2003-01-01

The biggest users of GRID technologies came from the science and technology communities. These consist of government, industry and academia (national and international). The NASA GRID is moving into a higher technology readiness level (TRL) today; and as a joint effort among these leaders within government, academia, and industry, the NASA GRID plans to extend availability to enable scientists and engineers across these geographical boundaries collaborate to solve important problems facing the world in the 21 st century. In order to enable NASA programs and missions to use IPG resources for program and mission design, the IPG capabilities needs to be accessible from inside the NASA center networks. However, because different NASA centers maintain different security domains, the GRID penetration across different firewalls is a concern for center security people. This is the reason why some IPG resources are been separated from the NASA center network. Also, because of the center network security and ITAR concerns, the NASA IPG resource owner may not have full control over who can access remotely from outside the NASA center. In order to obtain organizational approval for secured remote access, the IPG infrastructure needs to be adapted to work with the NASA business process. Improvements need to be made before the IPG can be used for NASA program and mission development. The Secured Advanced Federated Environment (SAFE) technology is designed to provide federated security across NASA center and NASA partner's security domains. Instead of one giant center firewall which can be difficult to modify for different GRID applications, the SAFE "micro security domain" provide large number of professionally managed "micro firewalls" that can allow NASA centers to accept remote IPG access without the worry of damaging other center resources. The SAFE policy-driven capability-based federated security mechanism can enable joint organizational and resource owner approved remote

Flywheel Rotor Safe-Life Technology

NASA Technical Reports Server (NTRS)

Ratner, J. K. H.; Chang, J. B.; Christopher, D. A.; McLallin, Kerry L. (Technical Monitor)

2002-01-01

Since the 1960s, research has been conducted into the use of flywheels as energy storage systems. The-proposed applications include energy storage for hybrid and electric automobiles, attitude control and energy storage for satellites, and uninterruptible power supplies for hospitals and computer centers. For many years, however, the use of flywheels for space applications was restricted by the total weight of a system employing a metal rotor. With recent technological advances in the manufacturing of composite materials, however, lightweight composite rotors have begun to be proposed for such applications. Flywheels with composite rotors provide much higher power and energy storage capabilities than conventional chemical batteries. However, the failure of a high speed flywheel rotor could be a catastrophic event. For this reason, flywheel rotors are classified by the NASA Fracture Control Requirements Standard as fracture critical parts. Currently, there is no industry standard to certify a composite rotor for safe and reliable operation forth( required lifetime of the flywheel. Technical problems hindering the development of this standard include composite manufacturing inconsistencies, insufficient nondestructive evaluation (NDE) techniques for detecting defects and/or impact damage, lack of standard material test methods for characterizing composite rotor design allowables, and no unified proof (over-spin) test for flight rotors. As part of a flywheel rotor safe-life certification pro-ram funded b the government, a review of the state of the art in composite rotors is in progress. The goal of the review is to provide a clear picture of composite flywheel rotor technologies. The literature review has concentrated on the following topics concerning composites and composite rotors: durability (fatigue) and damage tolerance (safe-life) analysis/test methods, in-service NDE and health monitoring techniques, spin test methods/ procedures, and containment options

Agricultural Safety. FMO: Fundamentals of Machine Operation. Second Edition.

ERIC Educational Resources Information Center

John Deere Co., Moline, IL.

This manual is intended to provide students with basic information on the safe operation of farm machinery. The following topics are covered in the individual chapters: safe farm machinery operation (the importance of safety, the role of communication in safety, and types of farm accidents); human factors (human limitations and capabilities;…

Safe Manual Jettison

NASA Technical Reports Server (NTRS)

Barton, Jay

2008-01-01

In space, the controlled release of certain cargoes is no less useful than the maritime jettisons from which they take their name but is also much more dangerous. Experience has shown that jettisons can be performed safely, but the process is complicated with the path to performing a jettison taking months or even years. In the background, time is also required to write procedures, train the crew, configure the vehicle, and many other activities. This paper outlines the current process used by the National Aeronautics and Space Administration (NASA) for manual jettisons, detailing the methods used to assure that the jettisons and the jettisoned objects are as safe as achievable and that the crew is adequately trained to be able to affect the safe jettison. The goal of this paper is not only to capture what it takes to perform safe jettisons in the near Earth environment but to extrapolate this knowledge to future space exploration scenarios that will likely have Extravehicular Activity (EVA) and International Partner (IP) interfaces.

A Framework for Safe Integration of Small UAS Into the NAS

NASA Technical Reports Server (NTRS)

Logan, Michael J.; Bland, Geoffrey; Murray, Jennifer

2011-01-01

This paper discusses a proposed framework for the safe integration of small unmanned aerial systems (sUAS) into the National Airspace System (NAS). The paper examines the potential uses of sUAS to build an understanding of the location and frequency of potential future flight operations based on the future applications of the sUAS systems. The paper then examines the types of systems that would be required to meet the application-level demand to determine classes of platforms and operations. Finally, a framework is proposed for both airworthiness and operations that attempts to balance safety with utility for these important systems.

Experience with fluorine and its safe use as a propellant

NASA Technical Reports Server (NTRS)

Bond, D. L.; Guenther, M. E.; Stimpson, L. D.; Toth, L. R.; Young, D. L.

1979-01-01

The industrial and the propulsion experience with fluorine and its derivatives is surveyed. The hazardous qualities of fluorine and safe handling procedures for the substance are emphasized. Procedures which fulfill the safety requirements during ground operations for handling fluorinated propulsion systems are discussed. Procedures to be implemented for use onboard the Space Transportation System are included.

3D thermal model of laser surface glazing for H13 tool steel

NASA Astrophysics Data System (ADS)

Kabir, I. R.; Yin, D.; Naher, S.

2017-10-01

In this work a three dimensional (3D) finite element model of laser surface glazing (LSG) process has been developed. The purpose of the 3D thermal model of LSG was to achieve maximum accuracy towards the predicted outcome for optimizing the process. A cylindrical geometry of 10mm diameter and 1mm length was used in ANSYS 15 software. Temperature distribution, depth of modified zone and cooling rates were analysed from the thermal model. Parametric study was carried out varying the laser power from 200W-300W with constant beam diameter and residence time which were 0.2mm and 0.15ms respectively. The maximum surface temperature 2554°K was obtained for power 300W and minimum surface temperature 1668°K for power 200W. Heating and cooling rates increased with increasing laser power. The depth of the laser modified zone attained for 300W power was 37.5µm and for 200W power was 30µm. No molten zone was observed at 200W power. Maximum surface temperatures obtained from 3D model increased 4% than 2D model presented in author's previous work. In order to verify simulation results an analytical solution of temperature distribution for laser surface modification was used. The surface temperature after heating was calculated for similar laser parameters which is 1689°K. The difference in maximum surface temperature is around 20.7°K between analytical and numerical analysis of LSG for power 200W.

Study on safety operation for large hydroelectric generator unit

NASA Astrophysics Data System (ADS)

Yan, Z. G.; Cui, T.; Zhou, L. J.; Zhi, F. L.; Wang, Z. W.

2012-11-01

Hydroelectric generator unit is a complex mechanical system which is composed of hydraulic turbine and electric generator. Rotary system is supported by the bearing bracket and the reinforced concrete structures, and vibration problem can't be avoided in the process of operating. Many large-scale hydroelectric units have been damaged because of the vibration problem in recent years. As the increase of the hydraulic turbine unit capacity and water head, the safe operation of hydraulic turbine has become a focus research in many countries. The operating characteristics of the hydraulic turbine have obvious differences at different working conditions. Based on the combination of field measurement and theoretical calculation, this paper shows a deep research on the safe operation of a large-scale Francis turbine unit. Firstly, the measurements of vibration, swing, pressure fluctuation and noise were carried out at 4 different heads. And also the relationships between vibrations and pressure fluctuations at different heads and working conditions were analysed deeply. Then the scientific prediction of safe operation for the unit at high head were done based on the CFD numerical calculation. Finally, this paper shows the division of the operating zone for the hydroelectric unit. According to the experimental results (vibrations, swings, pressure fluctuations and noise) as well as the theoretical results, the operating zone of the unit has been divided into three sections: prohibited operating zone, transition operating zone and safe operating zone. After this research was applied in the hydropower station, the security and economic efficiency of unit increased greatly, and enormous economic benefits and social benefits have been obtained.

An Information Framework for Facility Operators

DTIC Science & Technology

1991-01-01

and replacement products. Type: Type is used to decompose the building into smaller categories called arrangements, assemblies, parts, joints , and forro...are organized into crews and shops consisting of tradepersons responsible for building materials (concrete, masonry, metals, drywall , paint, etc...Comp Type (pre-cast, CIP) AS I Curing compound , sealant tyDe A S 04--- Masonry Comp Type (CMU, stone, glazed) A S I Manufacturer, style no., color no

Microanalysis of organic pigments and glazes in polychrome works of art by surface-enhanced resonance Raman scattering

PubMed Central

Leona, Marco

2009-01-01

Scientific studies of works of art are usually limited by severe sampling restrictions. The identification of organic colorants, a class of compounds relevant for attribution and provenance studies, is further complicated by the low concentrations at which these compounds are used and by the interference of the protein-, gum-, or oil-binding media present in pigment and glaze samples. Surface-enhanced resonance Raman scattering (SERRS) was successfully used to identify natural organic colorants in archaeological objects, polychrome sculptures, and paintings from samples smaller than 25 μm in diameter. The key factors in achieving the necessary sensitivity were a highly active stabilized silver colloid, obtained by the reproducible microwave-supported reduction of silver sulfate with glucose and sodium citrate, and a non-extractive hydrolysis sample treatment procedure that maximizes dye adsorption on the colloid. Among the examples presented are the earliest so far found occurrence of madder lake (in a 4,000 years old Egyptian object dating to the Middle Kingdom period), and the earliest known occurrence in Europe of the South Asian dyestuff lac (in the Morgan Madonna, a 12th century polychrome sculpture from Auvergne, France). PMID:19667181

Microanalysis of organic pigments and glazes in polychrome works of art by surface-enhanced resonance Raman scattering.

PubMed

Leona, Marco

2009-09-01

Scientific studies of works of art are usually limited by severe sampling restrictions. The identification of organic colorants, a class of compounds relevant for attribution and provenance studies, is further complicated by the low concentrations at which these compounds are used and by the interference of the protein-, gum-, or oil-binding media present in pigment and glaze samples. Surface-enhanced resonance Raman scattering (SERRS) was successfully used to identify natural organic colorants in archaeological objects, polychrome sculptures, and paintings from samples smaller than 25 microm in diameter. The key factors in achieving the necessary sensitivity were a highly active stabilized silver colloid, obtained by the reproducible microwave-supported reduction of silver sulfate with glucose and sodium citrate, and a non-extractive hydrolysis sample treatment procedure that maximizes dye adsorption on the colloid. Among the examples presented are the earliest so far found occurrence of madder lake (in a 4,000 years old Egyptian object dating to the Middle Kingdom period), and the earliest known occurrence in Europe of the South Asian dyestuff lac (in the Morgan Madonna, a 12th century polychrome sculpture from Auvergne, France).

What Influences Youth to Operate All-Terrain Vehicles Safely?

ERIC Educational Resources Information Center

Grummon, A. H.; Heaney, C. A.; Dellinger, W. A.; Wilkins, J. R., III

2014-01-01

The operation of all-terrain vehicles (ATVs) by youth has contributed to the incidence of serious and fatal injuries among children. This study explored factors related to the frequency with which youth wore a helmet and refrained from engaging in three risky driving behaviors (driving at risky speeds, on paved roads and on unfamiliar terrain)…

Emergency Response Virtual Environment for Safe Schools

NASA Technical Reports Server (NTRS)

Wasfy, Ayman; Walker, Teresa

2008-01-01

An intelligent emergency response virtual environment (ERVE) that provides emergency first responders, response planners, and managers with situational awareness as well as training and support for safe schools is presented. ERVE incorporates an intelligent agent facility for guiding and assisting the user in the context of the emergency response operations. Response information folders capture key information about the school. The system enables interactive 3D visualization of schools and academic campuses, including the terrain and the buildings' exteriors and interiors in an easy to use Web..based interface. ERVE incorporates live camera and sensors feeds and can be integrated with other simulations such as chemical plume simulation. The system is integrated with a Geographical Information System (GIS) to enable situational awareness of emergency events and assessment of their effect on schools in a geographic area. ERVE can also be integrated with emergency text messaging notification systems. Using ERVE, it is now possible to address safe schools' emergency management needs with a scaleable, seamlessly integrated and fully interactive intelligent and visually compelling solution.

Buying & Using Medicine Safely

MedlinePlus

... Generic Drugs - Patient Education Resources Patient and Prescriber materials: Videos, PSAs, factsheets and more. Spotlight Drugs@FDA Index to Drug-Specific Information Protecting Yourself Safe Disposal of Medicines Generic Medicines – safe, effective and ...

Adoption of the B2SAFE EUDAT replication service by the EPOS community

NASA Astrophysics Data System (ADS)

Cacciari, Claudio; Fares, Massimo; Fiameni, Giuseppe; Michelini, Alberto; Danecek, Peter; Wittenburg, Peter

2014-05-01

B2SAFE is the EUDAT service for moving and replicating data between sites and storage systems for different purposes. The goal of B2SAFE is to keep the data from a repository safe by replicating it across different geographical and administrative zones according to a set of well-defined policies. It is also a way to store large volumes of data permanently at those sites which are providing powerful on-demand data analysis facilities. In particular, B2SAFE operates on the domain of registered data where data objects are referable via persistent identifiers (PIDs). B2SAFE is more than just copying data because the PIDs must be carefully managed when data objects are moved or replicated. The EUDAT B2SAFE Service offers functionality to replicate datasets across different data centres in a safe and efficient way while maintaining all information required to easily find and query information about the replica locations. The information about the replica locations and other important information is stored in PID records, each managed in separate administrative domains. The B2SAFE Service is implemented as an iRODS module providing a set of iRODS rules or policies to interface with the EPIC handle API and uses the iRODS middleware to replicate datasets from a source data (or community) centre to a destination data centre. The definition of the dataset(s) to replicate is flexible and up to the communities using the B2SAFE service. While the B2SAFE is internally using the EPIC handle API, communities have the choice to use any PID system they prefer to assign PIDs to their digital objects. A reference to one or more EUDAT B2SAFE PIDs is returned by the B2SAFE service when a dataset is replicated. The presentation will introduce the problem space of B2SAFE, presents the achievements that have been made during the last year for enabling communities to make use of the B2SAFE service, demonstrates a EPOS use cases, outlines the commonalities and differences between the policies

A National Evaluation of Safe Schools/Healthy Students: Outcomes and Influences

ERIC Educational Resources Information Center

Derzon, James H.; Yu, Ping; Ellis, Bruce; Xiong, Sharon; Arroyo, Carmen; Mannix, Danyelle; Wells, Michael E.; Hill, Gary; Rollison, Julia

2012-01-01

The Safe Schools/Healthy Students (SS/HS) Initiative has awarded over $2 billion in grants to more than 350 school districts in partnership with local mental health, law enforcement, and juvenile justice agencies. To estimate the impact of grantee characteristics, grant operations, and near-term outcomes in reducing violence and substance use,…

Correction of small imperfections on white glazed china surfaces by laser radiation

NASA Astrophysics Data System (ADS)

Képíró, I.; Osvay, K.; Divall, M.

2007-07-01

A laser-assisted technique has been developed for correction of small diameter (1 mm) and shallow (0.5 mm) imperfections on the surface of gloss fired porcelain. To study the physics and establish the important parameters, artificially made holes in a porcelain sample have been first filled with correction material, then covered with raw glaze and treated by a pulsed, 7 kHz repetition rate CO 2 laser at 10.6 μm. The modification of the surface and the surrounding area have been quantified and studied with a large range of parameters of incident laser power (1-10 W), width of the laser pulses (10-125 μs) and duration of laser heating (60-480 s). Although the shine of the treated area, defined as the distribution of micro-droplets on the surface, is very similar to the untreated surfaces, the surroundings of the treated area usually show cracks. The measurement of both the spatial temperature distribution and the temporal cooling rate of the treated surface has revealed that a simple melting process always results in high gradient temperature distribution within the irradiated zone. Its inhomogeneous and fast cooling always generate at least micro-cracks on the surface within a few seconds after the laser was turned off. The duration and intensity of the laser irradiation have been then optimized in order to achieve the fastest possible melting of the surface, but without producing such high temperature gradients. To eliminate the cracks, more elaborated pre-heating and slowed-cooling-rate processes have been tried with prosperous results. These achievements complete our previous study, making possible to repair the most common surface imperfections and holes of gloss fired china samples.

36 CFR 9.41 - Operating standards.

Code of Federal Regulations, 2011 CFR

2011-07-01

... MINERALS MANAGEMENT Non-Federal Oil and Gas Rights § 9.41 Operating standards. The following standards... destroyed, obliterated, or damaged by such operations. (c) Whenever drilling or producing operations are... in a safe and workmanlike manner, having due regard for the preservation of the environment of the...

36 CFR 9.41 - Operating standards.

Code of Federal Regulations, 2013 CFR

2013-07-01

... MINERALS MANAGEMENT Non-Federal Oil and Gas Rights § 9.41 Operating standards. The following standards... destroyed, obliterated, or damaged by such operations. (c) Whenever drilling or producing operations are... in a safe and workmanlike manner, having due regard for the preservation of the environment of the...

49 CFR 179.400-23 - Operating instructions.

Code of Federal Regulations, 2011 CFR

2011-10-01

...-23 Operating instructions. All valves and gages must be clearly identified with corrosion-resistant nameplates. A plate of corrosion-resistant material bearing precautionary instructions for the safe operation...

49 CFR 179.400-23 - Operating instructions.

Code of Federal Regulations, 2012 CFR

2012-10-01

...-23 Operating instructions. All valves and gages must be clearly identified with corrosion-resistant nameplates. A plate of corrosion-resistant material bearing precautionary instructions for the safe operation...

49 CFR 179.400-23 - Operating instructions.

Code of Federal Regulations, 2013 CFR

2013-10-01

...-23 Operating instructions. All valves and gages must be clearly identified with corrosion-resistant nameplates. A plate of corrosion-resistant material bearing precautionary instructions for the safe operation...

49 CFR 179.400-23 - Operating instructions.

Code of Federal Regulations, 2014 CFR

2014-10-01

...-23 Operating instructions. All valves and gages must be clearly identified with corrosion-resistant nameplates. A plate of corrosion-resistant material bearing precautionary instructions for the safe operation...

ALMA Array Operations Group process overview

NASA Astrophysics Data System (ADS)

Barrios, Emilio; Alarcon, Hector

2016-07-01

ALMA Science operations activities in Chile are responsibility of the Department of Science Operations, which consists of three groups, the Array Operations Group (AOG), the Program Management Group (PMG) and the Data Management Group (DMG). The AOG includes the Array Operators and have the mission to provide support for science observations, operating safely and efficiently the array. The poster describes the AOG process, management and operational tools.

Air Quality Inside Police Drug Safes and Drug Storage Areas.

PubMed

Doran, Gregory S; Deans, Ralph; De Filippis, Carlo; Kostakis, Chris; Howitt, Julia A

2018-06-01

Storage of drug-based evidence inside sealed safes may allow chemical vapors to accumulate, creating concerns of drug exposure by inhalation, or the possibility of cross-contamination of drug evidence. Air samples were taken from inside eight drug safes and one small storage room at nine city and country police stations, as well as a large centralized drug evidence storage vault, in New South Wales (NSW), Australia. Sorbent tubes containing charcoal were used to determine whether any drug residues could be detected in the air, and to identify the types of chemicals present. Carbon traps were extracted and analyzed by LC-MS-MS for a suite of 22 licit and illicit drug residues and 2 metabolites. Carbon traps and SPME fibers were also analyzed by GC-MS for general volatile organic compound (VOC) residues. No detectable drug residues, either as airborne dust or vapor, were found in the safes, the storage room or the large central repository vault. No drugs were detected in any of the 34 urine samples collected at 8 of the 10 sampling locations, while only one of the five hair samples was positive for cocaine (9 pg/mg) provided by police exhibit officers at 3 of the 10 sampling locations. VOC analysis identified a variety of solvents associated with drug manufacture, plasticisers, personal care products and volatiles associated with plants such as cannabis. The results indicate that strong chemical odours emanating from drug safes are unlikely to be drug residues due to low volatility of drugs, and are more likely VOCs associated with their manufacture or from plant growing operations. Consideration should be given to the quality of air flow in rooms in which safes are housed and the use of air filtering inside safes to reduce the likelihood of VOC accumulation, and therefore the risk of human exposure.

Safe Operation of Mobile Unmanned Ground Vehicle (UGV) Systems

DTIC Science & Technology

2010-07-13

vehicle could go during uncommanded movement and full throttle acceleration. 4. TEST PROCEDURES. 4.1 Vehicle Subsystem Tests. These tests identify...time required to go from straight ahead to full deflection in one direction. (sec) i. Observations on ability of the remote operator to maintain...were well below the lateral acceleration limits of the vehicle resulting in very predictable handling traits. The primary concern , albeit subjective

B cells in operational tolerance.

PubMed

Chesneau, M; Danger, R; Soulillou, J-P; Brouard, S

2018-05-01

Transplantation is currently the therapy of choice for endstage organ failure even though it requires long-term immunosuppresive therapy, with its numerous side effects, for acceptance of the transplanted organ. In rare cases however, patients develop operational tolerance, that is, graft survival without immunosuppression. Studies conducted on these patients reveal genetic, phenotypic, and functional signatures. They provide a better understanding of the immunological mechanisms involved in operational tolerance and define biomarkers that could be used to adapt immunosuppressive treatment to the individual, safely reduce immunosuppression doses, and ideally and safely guide immunosuppression withdrawal. This review summarizes studies that suggest a role for B cells as biomarkers of operational tolerance and discusses the use of B cells as a predictive tool for immunologic risk. Copyright © 2018. Published by Elsevier Inc.

Global opportunities in land and water use while staying within the safe (and just) operating space: quantifications of interactions and tradeoffs

NASA Astrophysics Data System (ADS)

Gerten, Dieter; Jägermeyr, Jonas; Heck, Vera

2016-04-01

Staying within the safe and just operating space as defined by multiple planetary boundaries will be a major challenge especially in view of anticipated future increases in food demand, the potential need for balancing climate change (e.g. through terrestrial carbon dioxide removal) and its impacts, and the water and land demand associated with these goals and measures. This presentation will show simulation results from a comprehensive model-based study on the global potentials of diverse crop management options considered as opportunities to stay within the planetary boundaries for human freshwater use and land-system change. The quantified on-farm options include rainwater harvesting, soil conservation and more efficient irrigation, all of which are designed to use neither more water nor more land for agriculture than is presently the case. Results show that irrigation efficiency improvements could save substantial amounts of water in many river basins (globally 48% of non-productive water consumption in an ambitious scenario), and if rerouted to irrigate neighbouring rainfed systems, could at the same time boost kilocalorie production by 26% globally. Low-tech solutions for small-scale farmers on water-limited croplands show the potential to increase rainfed yields to a similar extent. In combination, such ambitious yet achievable integrated water management strategies could increase global kcal production by 41% and close the water-related yield gap by 62%. Global climate change would have adverse effects on crop yields in many regions, but the improvements in water management quantified here could buffer such effects to a significant degree. Thus, a substantial amount of anticipated future needs for food production could be fulfilled without further approaching / transgressing planetary boundaries. In addition, it will be shown how large-scale biomass plantations for the purpose of terrestrial CO2 removal (climate engineering, potentially implemented should

Cultivating the Art of Safe Space

ERIC Educational Resources Information Center

Hunter, Mary Ann

2008-01-01

Performance-making and peace-building are processes predicated on the production of safe space. But what is "safe space"? In performance-making, what is it that makes space safe without losing the creative potential of tension? What role is there for risk? And, once achieved, how does safe space become meaningful beyond its immediate…

Safe Affordable Fission Engine-(SAFE-) 100a Heat Exchanger Thermal and Structural Analysis

NASA Technical Reports Server (NTRS)

Steeve, B. E.

2005-01-01

A potential fission power system for in-space missions is a heat pipe-cooled reactor coupled to a Brayton cycle. In this system, a heat exchanger (HX) transfers the heat of the reactor core to the Brayton gas. The Safe Affordable Fission Engine- (SAFE-) 100a is a test program designed to thermally and hydraulically simulate a 95 Btu/s prototypic heat pipe-cooled reactor using electrical resistance heaters on the ground. This Technical Memorandum documents the thermal and structural assessment of the HX used in the SAFE-100a program.

Apollo Operations Handbook Lunar Module (LM 11 and Subsequent) Vol. 2 Operational Procedures

NASA Technical Reports Server (NTRS)

1971-01-01

The Apollo Operations Handbook (AOH) is the primary means of documenting LM descriptions and procedures. The AOH is published in two separately bound volumes. This information is useful in support of program management, engineering, test, flight simulation, and real time flight support efforts. This volume contains crew operational procedures: normal, backup, abort, malfunction, and emergency. These procedures define the sequence of actions necessary for safe and efficient subsystem operation.

Breastfeeding FAQs: Safely Storing Breast Milk

MedlinePlus

... Staying Safe Videos for Educators Search English Español Breastfeeding FAQs: Safely Storing Breast Milk KidsHealth / For Parents / Breastfeeding FAQs: Safely Storing Breast Milk What's in this ...

The safe home project.

PubMed

Arphorn, Sara; Jiraniratisai, Sopaphan; Rungtakul, Rungsri; Phutta, Nikom

2011-12-01

The Thai Health Promotion Foundation supported the Improvement of Quality of Life of Informal Workers project in Ban Luang District, Amphur Photaram, Ratchaburi Province. There were many informal workers in Ban Luang District. Sweet-crispy fish producers in Ban Luang were the largest group among the sweet-crispy fish producers in Thailand. This project was aimed at improving living and working conditions of informal workers, with a focus on the sweet-crispy fish group. Good practices of improved living and working conditions were used to help informal workers build safe, healthy and productive work environments. These informal workers often worked in substandard conditions and were exposed to various hazards in the working area. These hazards included risk of exposure to hot work environment, ergonomics-related injuries, chemical hazards, electrical hazards etc. Ergonomics problems were commonly in the sweet-crispy fish group. Unnatural postures such as prolonged sitting were performed dominantly. One hundred and fifty informal workers participated in this project. Occupational health volunteers were selected to encourage occupational health and safety in four groups of informal workers in 2009. The occupational health volunteers trained in 2008 were farmers, beauty salon workers and doll makers. The occupational health and safety knowledge is extended to a new informal worker group: sweet-crispy fish producer, in 2009. The occupational health and safety training for sweet-crispy fish group is conducted by occupational health volunteers. The occupational health volunteers increased their skills and knowledge assist in to make safe home and safe community through participatory oriented training. The improvement of living and working condition is conducted by using a modified WISH, Work Improvement for Safe Home, checklist. The plans of improvement were recorded. The informal workers showed improvement mostly on material handling and storage. The safe uses and safe

40 CFR 68.52 - Operating procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) CHEMICAL ACCIDENT PREVENTION PROVISIONS Program 2 Prevention Program § 68.52 Operating procedures. (a) The... for safely conducting activities associated with each covered process consistent with the safety information for that process. Operating procedures or instructions provided by equipment manufacturers or...

Designing a 'safe and just operating space' for the Chilika lagoon fishery of the Mahanadi delta, India

NASA Astrophysics Data System (ADS)

Cooper, Gregory; Dearing, John

2017-04-01

Annual fish production from the Chilika lagoon is worth US25-million/year, underpinning the livelihoods of 35,000 fishers and 200,000 secondary dependants. The system has a legacy of collapse, transitioning from annual production rates of 9000 tonnes to 1300 tonnes during the late-1980s, with resulting livelihood losses triggering the first recorded instances of economic migration from Chilika. Despite engineered recovery since 2000, the future persistence of Chilika's resource stock is uncertain. Climate change may strengthen freshwater and sediment delivery, promoting ecohydrological degradation through tidal outlet sedimentation, reduced salinity and freshwater weed growth. Simultaneously, human population growth, fleet motorisation and consumption demands threaten overexploitation driven collapse. These critical social-ecological drivers and feedbacks are projected into future by integrating system dynamics modelling with Monte Carlo inputs. Sustainable pathways are identified from outputs producing social-ecologically desirable futures, such as mid-century catch equalling maximum sustainable yield. The 'safe and just operating space' metaphor is regionalised by the limits of sustainable trajectories, such as the permissible number of active fishers, motorised boats and juvenile catch under alternative governance scenarios. These critical thresholds suggest policy-relevant guardrails for the sustainable governance of Chilika, in order to avoid regional productivity collapse, ecological degradation and livelihood losses. Benefits and trade-offs of alternative governance approaches are also discussed, aiding the optimisation of future regulatory decision-making.

14 CFR 91.1011 - Operational control responsibilities and delegation.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 2 2010-01-01 2010-01-01 false Operational control responsibilities and... Ownership Operations Operational Control § 91.1011 Operational control responsibilities and delegation. (a) Each owner in operational control of a program flight is ultimately responsible for safe operations and...

Ultra Safe And Secure Blasting System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hart, M M

2009-07-27

The Ultra is a blasting system that is designed for special applications where the risk and consequences of unauthorized demolition or blasting are so great that the use of an extraordinarily safe and secure blasting system is justified. Such a blasting system would be connected and logically welded together through digital code-linking as part of the blasting system set-up and initialization process. The Ultra's security is so robust that it will defeat the people who designed and built the components in any attempt at unauthorized detonation. Anyone attempting to gain unauthorized control of the system by substituting components or tappingmore » into communications lines will be thwarted in their inability to provide encrypted authentication. Authentication occurs through the use of codes that are generated by the system during initialization code-linking and the codes remain unknown to anyone, including the authorized operator. Once code-linked, a closed system has been created. The system requires all components connected as they were during initialization as well as a unique code entered by the operator for function and blasting.« less

How Safe Are Kid-Safe Search Engines?

ERIC Educational Resources Information Center

Masterson-Krum, Hope

2001-01-01

Examines search tools available to elementary and secondary school students, both human-compiled and crawler-based, to help direct them to age-appropriate Web sites; analyzes the procedures of search engines labeled family-friendly or kid safe that use filters; and tests the effectiveness of these services to students in school libraries. (LRW)

Safely Enabling Low-Altitude Airspace Operations: Unmanned Aerial System Traffic Management (UTM)

NASA Technical Reports Server (NTRS)

Kopardekar, Parimal

2015-01-01

Near-term Goal Enable initial low-altitude airspace and UAS operations with demonstrated safety as early as possible, within 5 years Long-term Goal Accommodate increased UAS operations with highest safety, efficiency, and capacity as much autonomously as possible (10-15 years).

SOME PROBLEMS OF "SAFE DOSE" ESTIMATION

EPA Science Inventory

In environmental carcinogenic risk assessment, the usually defined "safe doses" appear subjective in some sense. n this paper a method of standardizing "safe doses" based on some objective parameters is introduced and a procedure of estimating safe doses under the competing risks...

Void Fraction Instrument operation and maintenance manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

Borgonovi, G.; Stokes, T.I.; Pearce, K.L.

This Operations and Maintenance Manual (O&MM) addresses riser installation, equipment and personnel hazards, operating instructions, calibration, maintenance, removal, and other pertinent information necessary to safely operate and store the Void Fraction Instrument. Final decontamination and decommissioning of the Void Fraction Instrument are not covered in this document.

Hypergol Systems: Design, Buildup, and Operation

NASA Technical Reports Server (NTRS)

Baker, David; Rathgeber, Kurt

2006-01-01

This course was developed by personnel at the NASA JSC White Sands Test Facility in conjunction with the NASA Safety Training Center (NSTC). The NSTC was established in May 1991 by the NASA Headquarters Safety Directorate to provide up-to-date, high-quality, NASA specific safety training on location at NASA centers, or simultaneously to multiple centers over the Video Teleconferencing System (ViTS). Our desire is to establish and maintain a strong, long-lasting relationship with all NASA centers in order to fulfill your safety training needs on a cost-effective basis. Our ultimate goal is to provide a positive contribution to safe operations at NASA. NSTC Course 055 is a 2-day course discussing the safe usage of hypergols (hydrazine fuels and nitrogen tetroxide). During the course we will identify the hazards associated with hypergols including toxicity, reactivity, fire, and explosion. Management of risk is discussed in terms of the primary engineering controls design, buildup, and operation; and secondary controls personal protective equipment and detectors/monitors. The emphasis is on the design and buildup of compatible systems and the safe operation of these systems by technicians and engineers.

CALIPSO Instrument Operational

Atmospheric Science Data Center

2014-09-18

... been generated to current.   Due to elevated solar activity, CALIPSO payload was commanded to SAFE mode during the 10:45 UTC pass ... 11, 2014.  The CALIPSO Mission Operations Team is monitoring the space weather environment and is working with CNES to return to ...

CALIPSO Instrument Operational

Atmospheric Science Data Center

2014-03-05

... being briefly in data acquisition mode, the CALIPSO payload computer (PLC) was commanded OFF due to another solar event earlier this ... remain above the 10MeV threshold for laser operations. Science data is not acquired while the payload is in SAFE mode.   ...

Space station operations task force. Panel 2 report: Ground operations and support systems

NASA Technical Reports Server (NTRS)

1987-01-01

The Ground Operations Concept embodied in this report provides for safe multi-user utilization of the Space Station, eases user integration, and gives users autonomy and flexibility. It provides for meaningful multi-national participation while protecting U.S. interests. The concept also supports continued space operations technology development by maintaining NASA expertise and enabling technology evolution. Given attention here are pre/post flight operations, logistics, sustaining engineering/configuration management, transportation services/rescue, and information systems and communication.

Using Opioids Safely After Surgery

MedlinePlus

... Adult , Geriatric Using Opioids Safely After Surgery Using Opioids Safely After Surgery Stick to the lowest dose ... need opioid pain medicine. If your doctor says opioids aren’t necessary. If your doctor thinks you ...

How Safe Is Safe Enough for Self-Driving Vehicles?

PubMed

Liu, Peng; Yang, Run; Xu, Zhigang

2018-05-21

Self-driving vehicles (SDVs) promise to considerably reduce traffic crashes. One pressing concern facing the public, automakers, and governments is "How safe is safe enough for SDVs?" To answer this question, a new expressed-preference approach was proposed for the first time to determine the socially acceptable risk of SDVs. In our between-subject survey (N = 499), we determined the respondents' risk-acceptance rate of scenarios with varying traffic-risk frequencies to examine the logarithmic relationships between the traffic-risk frequency and risk-acceptance rate. Logarithmic regression models of SDVs were compared to those of human-driven vehicles (HDVs); the results showed that SDVs were required to be safer than HDVs. Given the same traffic-risk-acceptance rates for SDVs and HDVs, their associated acceptable risk frequencies of SDVs and HDVs were predicted and compared. Two risk-acceptance criteria emerged: the tolerable risk criterion, which indicates that SDVs should be four to five times as safe as HDVs, and the broadly acceptable risk criterion, which suggests that half of the respondents hoped that the traffic risk of SDVs would be two orders of magnitude lower than the current estimated traffic risk. The approach and these results could provide insights for government regulatory authorities for establishing clear safety requirements for SDVs. © 2018 Society for Risk Analysis.

Uranium Mill Tailings Remedial Action Project Safety Advancement Field Effort (SAFE) Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1994-02-01

In 1992, the Uranium Mill Tailings Remedial Action (UMTRA) Project experienced several health and safety related incidents at active remediation project sites. As a result, the U.S. Department of Energy (DOE) directed the Technical Assistance Contractor (TAC) to establish a program increasing the DOE`s overall presence at operational remediation sites to identify and minimize risks in operations to the fullest extent possible (Attachments A and B). In response, the TAC, in cooperation with the DOE and the Remedial Action Contractor (RAC), developed the Safety Advancement Field Effort (SAFE) Program.

14 CFR 23.237 - Operation on water.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Operation on water. 23.237 Section 23.237... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Flight Ground and Water Handling Characteristics § 23.237 Operation on water. A wave height, demonstrated to be safe for operation, and any...

14 CFR 23.237 - Operation on water.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Operation on water. 23.237 Section 23.237... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Flight Ground and Water Handling Characteristics § 23.237 Operation on water. A wave height, demonstrated to be safe for operation, and any...

14 CFR 23.237 - Operation on water.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Operation on water. 23.237 Section 23.237... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Flight Ground and Water Handling Characteristics § 23.237 Operation on water. A wave height, demonstrated to be safe for operation, and any...

14 CFR 23.237 - Operation on water.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Operation on water. 23.237 Section 23.237... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Flight Ground and Water Handling Characteristics § 23.237 Operation on water. A wave height, demonstrated to be safe for operation, and any...

Potential operating orbits for fission electric propulsion systems driven by the SAFE-400

NASA Astrophysics Data System (ADS)

Houts, Mike; Kos, Larry; Poston, David

2002-01-01

Safety must be ensured during all phases of space fission system design, development, fabrication, launch, operation, and shutdown. One potential space fission system application is fission electric propulsion (FEP), in which fission energy is converted into electricity and used to power high efficiency (Isp>3000s) electric thrusters. For these types of systems it is important to determine which operational scenarios ensure safety while allowing maximum mission performance and flexibility. Space fission systems are essentially non-radioactive at launch, prior to extended operation at high power. Once high power operation begins, system radiological inventory steadily increases as fission products build up. For a given fission product isotope, the maximum radiological inventory is typically achieved once the system has operated for a length of time equivalent to several half-lives. After that time, the isotope decays at the same rate it is produced, and no further inventory builds in. For an FEP mission beginning in Earth orbit, altitude and orbital lifetime increase as the propulsion system operates. Two simultaneous effects of fission propulsion system operation are thus (1) increasing fission product inventory and (2) increasing orbital lifetime. Phrased differently, as fission products build up, more time is required for the fission products to naturally convert back into non-radioactive isotopes. Simultaneously, as fission products build up, orbital lifetime increases, providing more time for the fission products to naturally convert back into non-radioactive isotopes. Operational constraints required to ensure safety can thus be quantified. .

Potential Operating Orbits for Fission Electric Propulsion Systems Driven by the SAFE-400

NASA Technical Reports Server (NTRS)

Houts, Mike; Kos, Larry; Poston, David; Rodgers, Stephen L. (Technical Monitor)

2002-01-01

Safety must be ensured during all phases of space fission system design, development, fabrication, launch, operation, and shutdown. One potential space fission system application is fission electric propulsion (FEP), in which fission energy is converted into electricity and used to power high efficiency (Isp greater than 3000s) electric thrusters. For these types of systems it is important to determine which operational scenarios ensure safety while allowing maximum mission performance and flexibility. Space fission systems are essentially nonradioactive at launch, prior to extended operation at high power. Once high power operation begins, system radiological inventory steadily increases as fission products build up. For a given fission product isotope, the maximum radiological inventory is typically achieved once the system has operated for a length of time equivalent to several half-lives. After that time, the isotope decays at the same rate it is produced, and no further inventory builds in. For an FEP mission beginning in Earth orbit, altitude and orbital lifetime increase as the propulsion system operates. Two simultaneous effects of fission propulsion system operation are thus (1) increasing fission product inventory and (2) increasing orbital lifetime. Phrased differently, as fission products build up, more time is required for the fission products to naturally convert back into non-radioactive isotopes. Simultaneously, as fission products build up, orbital lifetime increases, providing more time for the fission products to naturally convert back into non-radioactive isotopes. Operational constraints required to ensure safety can thus be quantified.

Smart aircraft fastener evaluation (SAFE) system: a condition-based corrosion detection system for aging aircraft

NASA Astrophysics Data System (ADS)

Schoess, Jeffrey N.; Seifert, Greg; Paul, Clare A.

1996-05-01

The smart aircraft fastener evaluation (SAFE) system is an advanced structural health monitoring effort to detect and characterize corrosion in hidden and inaccessible locations of aircraft structures. Hidden corrosion is the number one logistics problem for the U.S. Air Force, with an estimated maintenance cost of $700M per year in 1990 dollars. The SAFE system incorporates a solid-state electrochemical microsensor and smart sensor electronics in the body of a Hi-Lok aircraft fastener to process and autonomously report corrosion status to aircraft maintenance personnel. The long-term payoff for using SAFE technology will be in predictive maintenance for aging aircraft and rotorcraft systems, fugitive emissions applications such as control valves, chemical pipeline vessels, and industrial boilers. Predictive maintenance capability, service, and repair will replace the current practice of scheduled maintenance to substantially reduce operational costs. A summary of the SAFE concept, laboratory test results, and future field test plans is presented.

The United States Naval Nuclear Propulsion Program - Over 151 Million Miles Safely Steamed on Nuclear Power

DOE Office of Scientific and Technical Information (OSTI.GOV)

None, None

NNSA’s third mission pillar is supporting the U.S. Navy’s ability to protect and defend American interests across the globe. The Naval Reactors Program remains at the forefront of technological developments in naval nuclear propulsion and ensures a commanding edge in warfighting capabilities by advancing new technologies and improvements in naval reactor performance and reliability. In 2015, the Naval Nuclear Propulsion Program pioneered advances in nuclear reactor and warship design – such as increasing reactor lifetimes, improving submarine operational effectiveness, and reducing propulsion plant crewing. The Naval Reactors Program continued its record of operational excellence by providing the technical expertise requiredmore » to resolve emergent issues in the Nation’s nuclear-powered fleet, enabling the Fleet to safely steam more than two million miles. Naval Reactors safely maintains, operates, and oversees the reactors on the Navy’s 82 nuclear-powered warships, constituting more than 45 percent of the Navy’s major combatants.« less

Separation, Aspiration, and Fat Equalization: SAFE Liposuction Concepts for Comprehensive Body Contouring.

PubMed

Wall, Simeon H; Lee, Michael R

2016-12-01

Separation, aspiration, and fatty equilibration (SAFE) liposuction uses a process approach to body contouring and minimizes injury to surrounding structures. The multistep process allows for (1) fat separation, (2) lipoaspiration, and (3) fat equalization. The purpose of this study was to review both outcomes and complications of primary SAFE liposuction. Retrospective chart review was completed of patients undergoing SAFE liposuction from January of 2006 to January of 2011. Patient selection was limited to those undergoing liposuction alone with no adjuvant excisional procedures. Data were collected regarding demographics, body mass index, operative details, and outcomes. Seven hundred thirty-four patients were identified as having undergone SAFE liposuction. One hundred twenty-nine patients were found to have been treated with liposuction alone. Patient age ranged from 18 to 42 years and body mass index ranged from 18 to 42 kg/m (mean, 26.3 kg/m). Seven patients (5.4 percent) underwent treatment of the face and neck, six patients (4.7 percent) underwent treatment of upper extremities, 13 patients (10.1 percent) underwent treatment of the chest, 20 patients (15.5 percent) underwent treatment of lower extremities, 32 patients (24.8 percent) underwent treatment of the circumferential trunk, and 51 patients (39.5 percent) underwent treatment of circumferential trunk and additional area(s). No major complications occurred. Five of the 129 patients (3.87 percent) developed the minor complication of seroma formation. SAFE liposuction is a multistep process approach to body contouring consisting of (1) fat separation, (2) lipoaspiration, and (3) fat equalization. The results of this study show such technique to be safe and effective. Therapeutic, IV.

How to Safely Give Acetaminophen

MedlinePlus

... Educators Search English Español How to Safely Give Acetaminophen KidsHealth / For Parents / How to Safely Give Acetaminophen ... without getting a doctor's OK first. What Is Acetaminophen Also Called? Acetaminophen is the generic name of ...

Advanced laparoscopic bariatric surgery Is safe in general surgery training.

PubMed

Kuckelman, John; Bingham, Jason; Barron, Morgan; Lallemand, Michael; Martin, Matthew; Sohn, Vance

2017-05-01

Bariatric surgery makes up an increasing percentage of general surgery training. The safety of resident involvement in these complex cases has been questioned. We evaluated patient outcomes in resident performed laparoscopic bariatric procedures. Retrospective review of patients undergoing a laparoscopic bariatric procedure over seven years at a tertiary care single center. Procedures were primarily performed by a general surgery resident and proctored by an attending surgeon. Primary outcomes included operative volume, operative time and leak rate with perioperative outcomes evaluated as secondary outcomes. A total of 1649 bariatric procedures were evaluated. Operations included laparoscopic bypass (690) and laparoscopic sleeve gastrectomy (959). Average operating time was 136 min. Eighteen leaks (0.67%) were identified. Graduating residents performed an average of 89 laparoscopic bariatric cases during their training. There were no significant differences between resident levels with concern to operative time or leak rate (p 0.97 and p = 0.54). General surgery residents can safely perform laparoscopic bariatric surgery. When proctored by a staff surgeon, a resident's level of training does not significantly impact leak rate. Published by Elsevier Inc.

SONARC: A Sea Ice Monitoring and Forecasting System to Support Safe Operations and Navigation in Arctic Seas

NASA Astrophysics Data System (ADS)

Stephenson, S. R.; Babiker, M.; Sandven, S.; Muckenhuber, S.; Korosov, A.; Bobylev, L.; Vesman, A.; Mushta, A.; Demchev, D.; Volkov, V.; Smirnov, K.; Hamre, T.

2015-12-01

Sea ice monitoring and forecasting systems are important tools for minimizing accident risk and environmental impacts of Arctic maritime operations. Satellite data such as synthetic aperture radar (SAR), combined with atmosphere-ice-ocean forecasting models, navigation models and automatic identification system (AIS) transponder data from ships are essential components of such systems. Here we present first results from the SONARC project (project term: 2015-2017), an international multidisciplinary effort to develop novel and complementary ice monitoring and forecasting systems for vessels and offshore platforms in the Arctic. Automated classification methods (Zakhvatkina et al., 2012) are applied to Sentinel-1 dual-polarization SAR images from the Barents and Kara Sea region to identify ice types (e.g. multi-year ice, level first-year ice, deformed first-year ice, new/young ice, open water) and ridges. Short-term (1-3 days) ice drift forecasts are computed from SAR images using feature tracking and pattern tracking methods (Berg & Eriksson, 2014). Ice classification and drift forecast products are combined with ship positions based on AIS data from a selected period of 3-4 weeks to determine optimal vessel speed and routing in ice. Results illustrate the potential of high-resolution SAR data for near-real-time monitoring and forecasting of Arctic ice conditions. Over the next 3 years, SONARC findings will contribute new knowledge about sea ice in the Arctic while promoting safe and cost-effective shipping, domain awareness, resource management, and environmental protection.

A Human Proximity Operations System test case validation approach

NASA Astrophysics Data System (ADS)

Huber, Justin; Straub, Jeremy

A Human Proximity Operations System (HPOS) poses numerous risks in a real world environment. These risks range from mundane tasks such as avoiding walls and fixed obstacles to the critical need to keep people and processes safe in the context of the HPOS's situation-specific decision making. Validating the performance of an HPOS, which must operate in a real-world environment, is an ill posed problem due to the complexity that is introduced by erratic (non-computer) actors. In order to prove the HPOS's usefulness, test cases must be generated to simulate possible actions of these actors, so the HPOS can be shown to be able perform safely in environments where it will be operated. The HPOS must demonstrate its ability to be as safe as a human, across a wide range of foreseeable circumstances. This paper evaluates the use of test cases to validate HPOS performance and utility. It considers an HPOS's safe performance in the context of a common human activity, moving through a crowded corridor, and extrapolates (based on this) to the suitability of using test cases for AI validation in other areas of prospective application.

Making Human Spaceflight as Safe as Possible

NASA Technical Reports Server (NTRS)

Gregory, Frederick D.

2005-01-01

We articulated the safety hierarchy a little over two years ago, as part of our quest to be the nation s leader in safety and occupational health, and in the safety of the products and services we provide. The safety hierarchy stresses that we are all accountable for assuring that our programs, projects, and operations do not impact safety or health for the public, astronauts and pilots, employees on the ground, and high-value equipment and property. When people are thinking about doing things safely, they re also thinking about doing things right. And for the past couple of years, we ve had some pretty good results. In the time since the failures of the Mars 98 missions that occurred in late 1999, every NASA spacecraft launch has met the success objectives, and every Space Shuttle mission has safely and successfully met all mission objectives. Now I can t say that NASA s safety program is solely responsible for these achievements, but, as we like to say, "mission success starts with safety." In the future, looking forward, we will continue to make spaceflight even safer. That is NASA s vision. That is NASA s duty to both those who will travel into space and the American people who will make the journey possible.

78 FR 7477 - Multistate Corridor Operations and Management Program

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-01

... in the Multistate Corridor Operations and Management Program authorized by the Safe, Accountable... projects to improve multimodal transportation system management and operations. This notice seeks... Multistate Corridor Operations and Management (MCOM) programs and projects. The purpose of these investments...

Organising a safe space for navigating social-ecological transformations to sustainability.

PubMed

Pereira, Laura; Karpouzoglou, Timothy; Doshi, Samir; Frantzeskaki, Niki

2015-05-28

The need for developing socially just living conditions for the world's growing population whilst keeping human societies within a 'safe operating space' has become a modern imperative. This requires transformative changes in the dominant social norms, behaviours, governance and management regimes that guide human responses in areas such as urban ecology, public health, resource security (e.g., food, water, energy access), economic development and biodiversity conservation. However, such systemic transformations necessitate experimentation in public arenas of exchange and a deepening of processes that can widen multi-stakeholder learning. We argue that there is an emergent potential in bridging the sustainability transitions and resilience approaches to create new scientific capacity that can support large-scale social-ecological transformations (SETs) to sustainability globally, not just in the West. In this article, we elucidate a set of guiding principles for the design of a 'safe space' to encourage stronger interactions between these research areas and others that are relevant to the challenges faced. We envisage new opportunities for transdisciplinary collaboration that will develop an adaptive and evolving community of practice. In particular, we emphasise the great opportunity for engaging with the role of emerging economies in facilitating safe space experimentation.

Hydrophilicity, photocatalytic activity and stability of tetraethyl orthosilicate modified TiO2 film on glazed ceramic surface

NASA Astrophysics Data System (ADS)

Zhang, Peng; Tian, Jie; Xu, Ruifen; Ma, Guojun

2013-02-01

A new, simple, and low-cost method has been developed to enhance the surface properties of TiO2 film. Degussa P25-TiO2 nanoparticles were modified by tetraethyl orthosilicate (TEOS) on glazed ceramic tiles. Effects of tetraethyl orthosilicate modification on microstructure, crystal structure, hydrophilicity, photocatalytic activity and stability of the film were investigated. The obtained results showed that P25-TiO2/TEOS particles exhibited better dispersion, higher surface area, bigger surface roughness and smaller particle size comparing to pure P25-TiO2 particles, which resulted in better hydrophilicity after 10 days in a dark place and higher photocatalytic activity under visible light irradiation. 68% of Rhodamine B was degraded by P25-TiO2/TEOS film in 25 h with the light intensity of 5000 ± 500 lx, and degradation rate reached to 82% with the light intensity of 10,000 ± 1000 lx. Furthermore, two fundamentally different systems, in which the films recycle for repetitive degradation after soaked in dye solution and for discoloration after depositing dye on the surfaces, respectively, were measured to confirm that P25-TiO2/TEOS film showed excellently stable performances. Therefore the P25-TiO2/TEOS film we obtained has good washing resistance and would be a promising candidate for practical applications.

Safe Schools, Safe Students. Proceedings of the National Education Goals Panel/National Alliance of Pupil Services Organizations Conference on "Safe Schools, Safe Students: A Collaborative Approach to Achieving Safe, Disciplined, and Drug-free Schools Conducive to Learning" (Washington, D.C., October 28-29, 1994).

ERIC Educational Resources Information Center

Talley, Ronda C., Ed.; Walz, Garry R., Ed.

The "Safe Schools, Safe Students" conference brought together leading researchers and practitioners in order to share knowledge about innovative safety strategies being used in America's schools. The papers here represent the thinking of scientific experts and school-based pupil service providers who are implementing programs to prevent…

10 CFR 55.45 - Operating tests.

Code of Federal Regulations, 2010 CFR

2010-01-01

... significance of facility instrument readings. (5) Observe and safely control the operating behavior... equipment that could affect reactivity or the release of radioactive materials to the environment. (9...

76 FR 65561 - Multistate Corridor Operations and Management Program

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-21

... participation in the Multistate Corridor Operations and Management (MCOM) Program authorized by the Safe... transportation system management and operations. This notice seeks applications for available fiscal year (FY... system management and operations. Since the MCOM program is funded by the DOT Intelligent Transportation...

Steering teens safe: a randomized trial of a parent-based intervention to improve safe teen driving.

PubMed

Peek-Asa, Corinne; Cavanaugh, Joseph E; Yang, Jingzhen; Chande, Vidya; Young, Tracy; Ramirez, Marizen

2014-07-31

Crashes are the leading cause of death for teens, and parent-based interventions are a promising approach. We assess the effectiveness of Steering Teens Safe, a parent-focused program to increase safe teen driving. Steering Teens Safe aimed to improve parental communication with teens about safe driving using motivational interviewing techniques in conjunction with 19 safe driving lessons. A randomized controlled trial involved 145 parent-teen dyads (70 intervention and 75 control). Intervention parents received a 45-minute session to learn the program with four follow-up phone sessions, a DVD, and a workbook. Control parents received a standard brochure about safe driving. Scores were developed to measure teen-reported quantity and quality of parental communication about safe driving. The main outcome measure was a previously validated Risky Driving Score reported by teens. Because the Score was highly skewed, a generalized linear model based on a gamma distribution was used for analysis. Intervention teens ranked their parent's success in talking about driving safety higher than control teens (p = 0.035) and reported that their parents talked about more topics (non-significant difference). The Risky Driving Score was 21% lower in intervention compared to control teens (85% CI = 0.60, 1.00). Interaction between communication quantity and the intervention was examined. Intervention teens who reported more successful communication had a 42% lower Risky Driving Score (95% CI = 0.37, 0.94) than control parents with less successful communication. This program had a positive although not strong effect, and it may hold the most promise in partnership with other programs, such as Driver's Education or Graduated Driver's License policies. ClinicalTrials.gov NCT01014923. Registered Nov. 16, 2009.

Non-operative management of abdominal gunshot injuries: Is it safe in all cases?

PubMed

İflazoğlu, Nidal; Üreyen, Orhan; Öner, Osman Zekai; Meral, Ulvi Mehmet; Yülüklü, Murat

2018-01-01

In line with advances in diagnostic methods and expectation of a decrease in the number of negative laparotomies, selective non-operative management of abdominal gunshot wounds has been increasingly used over the last three decades. We aim to detect the possibility of treatment without surgery and present our experience in selected cases referred from Syria to a hospital at the Turkish-Syrian border. Between February 2012 and June 2014, patients admitted with abdominal gunshot wounds were analyzed. Computed tomography was performed for all patients on admission. Patients who were hemodynamically stable and did not have symptoms of peritonitis at the time of presentation were included in the study. The primary outcome parameters were mortality and morbidity. Successful selective non-operative management (Group 1) and unsuccessful selective non-operative management (Group 2) groups were compared in terms of complications, blood transfusion, injury site, injury severity score (ISS), and hospital stay. Of 158 truncal injury patients, 18 were considered feasible for selective non-operative management. Of these, 14 (78%) patients were treated without surgery. Other Four patients were operated upon progressively increasing abdominal pain and tenderness during follow-up. On diagnostic exploration, all of these cases had intestinal perforations. No mortality was observed in selective non-operative management. There was no statistically significant difference between Group 1 and Group 2, in terms of length of hospital stay (96 and 127 h, respectively). Also, there was no difference between groups in terms of blood transfusion necessity, injury site, complication rate, and injury severity score (p>0.05). Decision making on patient selection for selective non-operative management is critical to ensure favorable outcomes. It is not possible to predict the success of selective non-operative management in advance. Cautious clinical examination and close monitoring of these

Safe biodegradable fluorescent particles

DOEpatents

Martin, Sue I [Berkeley, CA; Fergenson, David P [Alamo, CA; Srivastava, Abneesh [Santa Clara, CA; Bogan, Michael J [Dublin, CA; Riot, Vincent J [Oakland, CA; Frank, Matthias [Oakland, CA

2010-08-24

A human-safe fluorescence particle that can be used for fluorescence detection instruments or act as a safe simulant for mimicking the fluorescence properties of microorganisms. The particle comprises a non-biological carrier and natural fluorophores encapsulated in the non-biological carrier. By doping biodegradable-polymer drug delivery microspheres with natural or synthetic fluorophores, the desired fluorescence can be attained or biological organisms can be simulated without the associated risks and logistical difficulties of live microorganisms.

Safe Haven.

ERIC Educational Resources Information Center

Bush, Gail

2003-01-01

Discusses school libraries as safe havens for teenagers and considers elements that foster that atmosphere, including the physical environment, lack of judgments, familiarity, leisure, and a welcoming nature. Focuses on the importance of relationships, and taking the time to listen to teens and encourage them. (LRW)

Establishment of design criteria for acceptable failure modes and fail safe considerations for the space shuttle structural system

NASA Technical Reports Server (NTRS)

Westrup, R. W.

1972-01-01

Investigations of fatigue life, and safe-life and fail-safe design concepts as applied to space shuttle structure are summarized. The results are evaluated to select recommended structural design criteria to provide assurance that premature failure due to propagation of undetected crack-like defects will not occur during shuttle operational service. The space shuttle booster, GDC configuration B-9U, is selected as the reference vehicle. Structural elements used as basis of detail analyses include wing spar caps, vertical stabilizer skins, crew compartment skin, orbiter support frame, and propellant tank shell structure. Fatigue life analyses of structural elements are performed to define potential problem areas and establish upper limits of operating stresses. Flaw growth analyses are summarized in parametric form over a range of initial flaw types and sizes, operating stresses and service life requirements. Service life of 100 to 500 missions is considered.

More than a Safe Space

ERIC Educational Resources Information Center

Sadowski, Michael

2016-01-01

Over the past three decades, much of the conversation about LGBTQ students in schools has centered on safety--anti-bullying policies, the "safe space" of gay-straight alliances, and "safe zones" marked by rainbow-colored stickers on classroom doors. In this article, Michael Sadowski argues that it's time to move beyond safety…

Development of safe infrared gas lasers

NASA Astrophysics Data System (ADS)

Mainuddin; Singhal, Gaurav; Tyagi, R. K.; Maini, A. K.

2013-04-01

Infrared gas lasers find application in numerous civil and military areas. Such lasers are therefore being developed at different institutions around the world. However, the development of chemical infrared gas lasers such as chemical oxygen iodine lasers (COIL) involves the use of several hazardous chemicals. In order to exploit full potential of these lasers, one must take diligent care of the safety issues associated with the handling of these chemicals and the involved processes. The present paper discusses the safety aspects to be taken into account in the development of these infrared gas lasers including various detection sensors working in conjunction with a customized data acquisition system loaded with safety interlocks for safe operation. The developed safety schemes may also be implemented for CO2 gas dynamic laser (GDL) and hydrogen fluoride-deuterium fluoride (HF-DF) Laser.

"Safe Schools within Safe Communities: A Regional Summit in the Heartland." Policy Briefs Special Report.

ERIC Educational Resources Information Center

Huertas, Aurelio, Jr.; Sullivan, Carol

This report documents the proceedings of a regional policy seminar hosted by the Iowa Department of Education with support from the North Central Regional Educational Laboratory (NCREL) and the Midwest Regional Center for Drug-Free Schools and Communities (MRC). The seminar, "Safe Schools Within Safe Communities," was held on September 19-20,…

How safe are HEMS-programmes in Germany? A retrospective analysis.

PubMed

Thies, Karl-Christian; Sep, Daan; Derksen, Remon

2006-03-01

Recent accidents with helicopter emergency medical service (HEMS) aircraft raise the question how safe HEMS in Germany is and how accidents could be prevented. We surveyed all German HEMS-programmes and reviewed the data of the German Aviation Authority regarding accidents with HEMS. An average German HEMS-programme encounters one accident leading to at least severe damage or loss of the helicopter in 26 operating years, one accident resulting in casualties in 65 operating years and one fatal accident in 111 operating years. The major causes of accidents were obstacle strikes during landing at the scene. Flying in bad weather conditions and lack of discipline were other factors contributing to HEMS-accidents. HEMS-safety could be improved by special training programmes for pilots and HEMS-crewmembers to address the factors listed above. Safety training for doctors is recommended but we did not find support for the notion of changing the doctor's legal position of a passenger to a HEMS-crewmember.

Nonspecific abdominal pain is a safe diagnosis.

PubMed

Pennel, David John Laurie; Goergen, Nina; Driver, Chris P

2014-11-01

The aim of this study is to assess if a clinical diagnosis of nonspecific abdominal pain (NSAP) is safe and if patients with this initial diagnosis are likely to require further investigation or surgical intervention. 3323 patients admitted with NSAP from July 1990 to September 2012 utilizing a prospective database of all surgical admissions were included. Readmission over the period of the study and specifically within 30 days of their initial presentation was identified together with any invasive investigation or surgical intervention. 319 children (9.6%) were subsequently readmitted with abdominal pain at some point during the study period. Of these, 78 (2.3%) were readmitted within 30 days. 118 (3.5%) children subsequently had an operation or invasive investigation some point following their initial admission. Of these 33 (0.6%) had the procedure within 3 months of the initial admission. 13 patients had an appendicectomy within 3 months of the initial presentation. Of these histology confirmed appendicitis in 8 patients. This gives an overall incidence of "missed" appendicitis of 0.2 % (8/3323). This study confirms that a clinical diagnosis of nonspecific abdominal pain (NSAP) is safe in a pediatric population and the risk of "missing" appendicitis is only 0.2%. Patients and/or parents can be confidently reassured that the risk of missing organic pathology is very low. Copyright © 2014 Elsevier Inc. All rights reserved.

Safe Use Practices for Pesticides

Science.gov Websites

; Environment Human Health Animal Health Safe Use Practices Food Safety Environment Air Water Soil Wildlife Ingredients Low-Risk Pesticides Organic Pesticide Ingredients Pesticide Incidents Human Exposure Pet Exposure Home Page Pesticide Health and Safety Information Safe Use Practices for Pesticides Related Topics

Is Prevent a Safe Space?

ERIC Educational Resources Information Center

Ramsay, Peter

2017-01-01

In this article, I test the claims of the UK government and universities that the Prevent programme aims to create a safe space for the discussion of "extremist" ideas in universities. I do this by comparing the main elements of the Prevent duty that has been imposed on universities with those of safe spaces as imagined by student…

75 FR 29391 - National Safe Boating Week, 2010

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-26

... Safe Boating Week, 2010 By the President of the United States of America A Proclamation Our Nation's... National Safe Boating Week to practicing safe techniques so boaters of all ages can enjoy this pastime... annually the 7-day period prior to Memorial Day weekend as ``National Safe Boating Week.'' NOW, THEREFORE...

Organising a Safe Space for Navigating Social-Ecological Transformations to Sustainability

PubMed Central

Pereira, Laura; Karpouzoglou, Timothy; Doshi, Samir; Frantzeskaki, Niki

2015-01-01

The need for developing socially just living conditions for the world’s growing population whilst keeping human societies within a ‘safe operating space’ has become a modern imperative. This requires transformative changes in the dominant social norms, behaviours, governance and management regimes that guide human responses in areas such as urban ecology, public health, resource security (e.g., food, water, energy access), economic development and biodiversity conservation. However, such systemic transformations necessitate experimentation in public arenas of exchange and a deepening of processes that can widen multi-stakeholder learning. We argue that there is an emergent potential in bridging the sustainability transitions and resilience approaches to create new scientific capacity that can support large-scale social-ecological transformations (SETs) to sustainability globally, not just in the West. In this article, we elucidate a set of guiding principles for the design of a ‘safe space’ to encourage stronger interactions between these research areas and others that are relevant to the challenges faced. We envisage new opportunities for transdisciplinary collaboration that will develop an adaptive and evolving community of practice. In particular, we emphasise the great opportunity for engaging with the role of emerging economies in facilitating safe space experimentation. PMID:26030471

30 CFR 77.312 - Fail safe monitoring systems.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Fail safe monitoring systems. 77.312 Section 77... Thermal Dryers § 77.312 Fail safe monitoring systems. Thermal dryer systems and controls shall be protected by a fail safe monitoring system which will safely shut down the system and any related equipment...

30 CFR 77.312 - Fail safe monitoring systems.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Fail safe monitoring systems. 77.312 Section 77... Thermal Dryers § 77.312 Fail safe monitoring systems. Thermal dryer systems and controls shall be protected by a fail safe monitoring system which will safely shut down the system and any related equipment...

30 CFR 77.312 - Fail safe monitoring systems.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Fail safe monitoring systems. 77.312 Section 77... Thermal Dryers § 77.312 Fail safe monitoring systems. Thermal dryer systems and controls shall be protected by a fail safe monitoring system which will safely shut down the system and any related equipment...

30 CFR 77.312 - Fail safe monitoring systems.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Fail safe monitoring systems. 77.312 Section 77... Thermal Dryers § 77.312 Fail safe monitoring systems. Thermal dryer systems and controls shall be protected by a fail safe monitoring system which will safely shut down the system and any related equipment...

30 CFR 77.312 - Fail safe monitoring systems.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Fail safe monitoring systems. 77.312 Section 77... Thermal Dryers § 77.312 Fail safe monitoring systems. Thermal dryer systems and controls shall be protected by a fail safe monitoring system which will safely shut down the system and any related equipment...

29 CFR 1915.15 - Maintenance of safe conditions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Enclosed Spaces and Other Dangerous Atmospheres in Shipyard Employment § 1915.15 Maintenance of safe... into spaces that have been certified “Safe for Workers” or “Safe for Hot Work” shall be disconnected... certificates. A competent person shall visually inspect and test each space certified as “Safe for Workers” or...

29 CFR 1915.15 - Maintenance of safe conditions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Enclosed Spaces and Other Dangerous Atmospheres in Shipyard Employment § 1915.15 Maintenance of safe... into spaces that have been certified “Safe for Workers” or “Safe for Hot Work” shall be disconnected... certificates. A competent person shall visually inspect and test each space certified as “Safe for Workers” or...

Staying Healthy and Safe at Work

MedlinePlus

... The Prematurity Campaign About us Annual report Our work Community impact Global programs Research Need help? Frequently ... safe at work Staying healthy and safe at work E-mail to a friend Please fill in ...

33 CFR 83.06 - Safe speed (Rule 6).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Safe speed (Rule 6). 83.06... Safe speed (Rule 6). Every vessel shall at all times proceed at a safe speed so that she can take... prevailing circumstances and conditions. In determining a safe speed the following factors shall be among...

33 CFR 83.06 - Safe speed (Rule 6).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 1 2011-07-01 2011-07-01 false Safe speed (Rule 6). 83.06... Safe speed (Rule 6). Every vessel shall at all times proceed at a safe speed so that she can take... prevailing circumstances and conditions. In determining a safe speed the following factors shall be among...

Unmanned Aircraft Systems Traffic Management (UTM) Safely Enabling UAS Operations in Low-Altitude Airspace

NASA Technical Reports Server (NTRS)

Kopardekar, Parimal H.

2017-01-01

Conduct research, development and testing to identify airspace operations requirements to enable large-scale visual and beyond visual line of sight UAS operations in the low-altitude airspace. Use build-a-little-test-a-little strategy remote areas to urban areas Low density: No traffic management required but understanding of airspace constraints. Cooperative traffic management: Understanding of airspace constraints and other operations. Manned and unmanned traffic management: Scalable and heterogeneous operations. UTM construct consistent with FAAs risk-based strategy. UTM research platform is used for simulations and tests. UTM offers path towards scalability

High Pulse Repetition Rate, Eye Safe, Visible Wavelength Lidar Systems: Design, Results and Potential

NASA Technical Reports Server (NTRS)

Spinhirne, James; Berkoff, Timothy; Welton, Elsworth; Campbell, James; OCStarr, David (Technical Monitor)

2002-01-01

In 1993 the first of the eye safe visible wavelength lidar systems known now as Micro Pulse Lidar (MPL) became operational. Since that time there have been several dozen of these systems produced and applied for full time profiling of atmospheric cloud and aerosol structure. There is currently an observational network of MPL sites to support global climate research. In the course of application of these instruments there have been significant improvements in understanding, design and performance of the systems. There are addition potential and applications beyond current practice for the high repetition rate, eye safe designs. The MPL network and the current capability, design and future potential of MPL systems are described.

Realistic Testing of the Safe Affordable Fission Engine (SAFE-100) Thermal Simulator Using Fiber Bragg Gratings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stinson-Bagby, Kelly L.; Fielder, Robert S.; Van Dyke, Melissa K.

2004-02-04

The motivation for the reported research was to support NASA space nuclear power initiatives through the development of advanced fiber optic sensors for space-based nuclear power applications. Distributed high temperature measurements were made with 20 FBG temperature sensors installed in the SAFE-100 thermal simulator at the NASA Marshal Space Flight Center. Experiments were performed at temperatures approaching 800 deg. C and 1150 deg. C for characterization studies of the SAFE-100 core. Temperature profiles were successfully generated for the core during temperature increases and decreases. Related tests in the SAFE-100 successfully provided strain measurement data.

49 CFR 398.5 - Parts and accessories necessary for safe operation.

Code of Federal Regulations, 2010 CFR

2010-10-01

... inches of space between the backrests or between the edges of the opposite seats when face to face.... 398.5 Section 398.5 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL... vehicle, or cause or permit it to be operated, unless it is equipped in accordance with said requirements...

33 CFR 62.27 - Safe water marks.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Safe water marks. 62.27 Section 62.27 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY AIDS TO NAVIGATION UNITED STATES AIDS TO NAVIGATION SYSTEM The U.S. Aids to Navigation System § 62.27 Safe water marks. Safe...

75 FR 1734 - Children’s Online Privacy Protection Rule Safe Harbor Proposed Self-Regulatory Guidelines; i-SAFE...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-13

...The Federal Trade Commission publishes this notice and request for public comment concerning proposed self-regulatory guidelines submitted by i-SAFE, Inc. under the safe harbor provision of the Children's Online Privacy Protection Rule.

40 CFR 243.201-2 - Recommended procedures: Operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... waste handling techniques, and in the proper operation of collection equipment, such as those presented in Operation Responsible: Safe Refuse Collection. (b) Personal protective equipment such as gloves... Standards for Subpart I—Personal Protective Equipment (29 CFR 1910.132 through 1910.137). (c) Scavenging...

40 CFR 243.201-2 - Recommended procedures: Operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... waste handling techniques, and in the proper operation of collection equipment, such as those presented in Operation Responsible: Safe Refuse Collection. (b) Personal protective equipment such as gloves... Standards for Subpart I—Personal Protective Equipment (29 CFR 1910.132 through 1910.137). (c) Scavenging...

33 CFR 62.27 - Safe water marks.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 1 2011-07-01 2011-07-01 false Safe water marks. 62.27 Section... UNITED STATES AIDS TO NAVIGATION SYSTEM The U.S. Aids to Navigation System § 62.27 Safe water marks. Safe water marks indicate that there is navigable water all around the mark. They are often used to indicate...

33 CFR 62.27 - Safe water marks.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 1 2014-07-01 2014-07-01 false Safe water marks. 62.27 Section... UNITED STATES AIDS TO NAVIGATION SYSTEM The U.S. Aids to Navigation System § 62.27 Safe water marks. Safe water marks indicate that there is navigable water all around the mark. They are often used to indicate...

33 CFR 62.27 - Safe water marks.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 1 2013-07-01 2013-07-01 false Safe water marks. 62.27 Section... UNITED STATES AIDS TO NAVIGATION SYSTEM The U.S. Aids to Navigation System § 62.27 Safe water marks. Safe water marks indicate that there is navigable water all around the mark. They are often used to indicate...

Removing Hair Safely

MedlinePlus

... For Consumers Home For Consumers Consumer Updates Removing Hair Safely Share Tweet Linkedin Pin it More sharing ... related to common methods of hair removal. Laser Hair Removal In this method, a laser destroys hair ...

A fail-safe CMOS logic gate

NASA Technical Reports Server (NTRS)

Bobin, V.; Whitaker, S.

1990-01-01

This paper reports a design technique to make Complex CMOS Gates fail-safe for a class of faults. Two classes of faults are defined. The fail-safe design presented has limited fault-tolerance capability. Multiple faults are also covered.

Safe mobility for older people notebook

DOT National Transportation Integrated Search

1999-04-01

The Safe Mobility for Older People Notebook is a research product of the "Model Driver Screening and Evaluation Program" project sponsored by NHTSA, and is intended as a resource to support program initiatives promoting the safe mobility of older per...

Safe Zone of Posterior Screw Insertion for Talar Neck Fractures on 3-Dimensional Reconstruction Model.

PubMed

Wu, Jian-Qun; Ma, Sheng-Hui; Liu, Song; Qin, Cheng-He; Jin, Dan; Yu, Bin

2017-02-01

To investigate the optimal posterior screw placement and the geometry of safe zones for screw insertion in the talar neck. Computed tomography data for 15 normal feet were imported into Mimics 10.01 software for 3-dimensional reconstruction; 4.0-mm-diameter screws were simulated from the lateral tubercle of the posterior process of the talus to the talar head. The range of screw paths trajectories and screw lengths at nine locations that did not breach the cortex of the talus were evaluated. In addition, the farthest (point a) and nearest point (point b) of the safe zone to the subtalar joint at each location, the anteversion angle (angle A), which is parallel to the sagittal plane, and the horizontal angle (angle B), which is perpendicular to the sagittal plane, were measured. The safe zone was mainly between the 30% location and the 60% location; the width of each safe zone was 13.6° ± 1.4°; the maximum height of each safe zone was 7.8° ± 1.2°. The height of the safe zone was lowest at the 30% location (4.5°) and highest at the 50% location (7.3°). The mixed safe zone of all tali was between the 50% location and the 60% location. When a screw was inserted at point a, the safe entry distance (screw length) ranged from 48.8 to 49.5 mm, and when inserted to point b, the distance ranged from 48.2 to 48.9 mm. And inserting a 48.7 mm screw, 5.6° laterally and 7.4° superiorly, from the lateral tubercle of the posterior process of the talus towards the talar head is safest. The safe zone of posterior screw fixation have been defined applying to most talus, assuming the fractures are well reduced, this may strengthen the stability, shorten the operation time and reduce the incidence of surgical complications. © 2017 Chinese Orthopaedic Association and John Wiley & Sons Australia, Ltd.

33 CFR 62.27 - Safe water marks.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 1 2012-07-01 2012-07-01 false Safe water marks. 62.27 Section 62.27 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY AIDS TO NAVIGATION UNITED STATES AIDS TO NAVIGATION SYSTEM The U.S. Aids to Navigation System § 62.27 Safe water marks. Safe water marks indicate that there is...

Developing Safe Schools Partnerships with Law Enforcement

ERIC Educational Resources Information Center

Rosiak, John

2009-01-01

Safe schools are the concern of communities throughout the world. If a school is safe, and if children feel safe, students "are better able to learn. But what are the steps to make" this happen? First, it is important to understand the problem: What are the threats to school safety? These include crime-related behaviors that find their way to…

Highway Maintenance Equipment Operator. Miscellaneous Equipment. Training Materials.

ERIC Educational Resources Information Center

Perky, Sandra Dutreau; And Others

This curriculum guide provides instructional materials to assist in training equipment operators in the safe and effective use of highway maintenance equipment. It includes six units of instruction covering the small, specialized equipment used in maintenance operations. Each unit of instruction consists of eight basic components: performance…

Combating Terrorism: U.S. Government Strategies and Efforts to Deny Terrorists Safe Haven

DTIC Science & Technology

2011-06-03

havens—such as activities funded through State’s Peacekeeping Operations and State-funded DHS training to combat money laundering and bulk cash...Management, Committee on Homeland Security House of Representatives COMBATING TERRORISM U.S. Government Strategies and Efforts to Deny Terrorists... Combating Terrorism: U.S. Government Strategies and Efforts to Deny Terrorists Safe Haven 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT

Safe haven laws as crime control theater.

PubMed

Hammond, Michelle; Miller, Monica K; Griffin, Timothy

2010-07-01

This article examines safe haven laws, which allow parents to legally abandon their infants. The main objective is to determine whether safe haven laws fit the criteria of crime control theater, a term used to describe public policies that produce the appearance, but not the effect, of crime control, and as such are essentially socially constructed "solutions" to socially constructed crime "problems." The analysis will apply the principles of crime control theater to safe haven laws. Specifically, the term crime control theater applies to laws that are reactionary responses to perceived criminal threats and are often widely supported as a way to address the crime in question. Such laws are attractive because they appeal to mythic narratives (i.e., saving an innocent child from a predator); however they are likely ineffective due to the complexity of the crime. These laws can have deleterious effects when policymakers make false claims of success and stunt public discourse (e.g., drawing attention away from more frequent and preventable crimes). This analysis applies these criteria to safe haven laws to determine whether such laws can be classified as crime control theater. Many qualities inherent to crime control theater are present in safe haven laws. For example, the laws are highly publicized, their intentions lack moral ambiguity, rare cases of success legitimize law enforcement and other agencies, and they appeal to the public sense of responsibility in preventing crime. Yet the goal of saving infant lives may be unattainable. These qualities make the effectiveness of the laws questionable and suggest they may be counterproductive. This analysis determined that safe haven laws are socially constructed solutions to the socially constructed problem of child abandonment. Safe haven laws are appropriately classified as crime control theater. It is imperative that further research be conducted to examine the effectiveness and collateral effects of safe haven laws

Safe Sleep Practices of Kansas Birthing Hospitals

PubMed Central

Ahlers-Schmidt, Carolyn R.; Schunn, Christy; Sage, Cherie; Engel, Matthew; Benton, Mary

2018-01-01

Background Sleep-related death is tied with congenital anomalies as the leading cause of infant mortality in Kansas, and external risk factors are present in 83% of these deaths. Hospitals can impact caregiver intentions to follow risk-reduction strategies. This project assessed the current practices and policies of Kansas hospitals with regard to safe sleep. Methods A cross-sectional survey of existing safe sleep practices and policies in Kansas hospitals was performed. Hospitals were categorized based on reported delivery volume and data were compared across hospital sizes. Results Thirty-one of 73 (42%) contacted hospitals responded. Individual survey respondents represented various hospital departments including newborn/well-baby (68%), neonatal intensive care unit (3%) and other non-nursery departments or administration (29%). Fifty-eight percent of respondents reported staff were trained on infant safe sleep; 44% of these held trainings annually. High volume hospitals tended to have more annual training than low or mid volume birth hospitals. Thirty-nine percent reported a safe sleep policy, though most of these (67%) reported never auditing compliance. The top barrier to safe sleep education, regardless of delivery volume, was conflicting patient and family member beliefs. Conclusions Hospital promotion of infant safe sleep is being conducted in Kansas to varying degrees. High and mid volume birth hospitals may need to work more on formal auditing of safe sleep practices, while low volume hospitals may need more staff training. Low volume hospitals also may benefit from access to additional caregiver education materials. Finally, it is important to note hospitals should not be solely responsible for safe sleep education. PMID:29844848

Nothing Virtual About it: An Emerging Safe Haven for an Adaptive Enemy

DTIC Science & Technology

2010-12-02

TERRORISTS May Allah bless you lions of the front, for by Allah, the fruits of your combined efforts-- sound, video, and text—are more severe for the...insurgencies, as demonstrated in the Soviet-Afghan War and many other conflicts exists and for many insurgencies perhaps is its operational center of...who have limited geographical safe havens, the Internet is becoming of equal or greater importance if not their center of gravity. The Birth of Al

Towards apparent convergence in asymptotically safe quantum gravity

NASA Astrophysics Data System (ADS)

Denz, T.; Pawlowski, J. M.; Reichert, M.

2018-04-01

The asymptotic safety scenario in gravity is accessed within the systematic vertex expansion scheme for functional renormalisation group flows put forward in Christiansen et al. (Phys Lett B 728:114, 2014), Christiansen et al. (Phy Rev D 93:044036, 2016), and implemented in Christiansen et al. (Phys Rev D 92:121501, 2015) for propagators and three-point functions. In the present work this expansion scheme is extended to the dynamical graviton four-point function. For the first time, this provides us with a closed flow equation for the graviton propagator: all vertices and propagators involved are computed from their own flows. In terms of a covariant operator expansion the current approximation gives access to Λ , R, R^2 as well as R_{μ ν }^2 and higher derivative operators. We find a UV fixed point with three attractive and two repulsive directions, thus confirming previous studies on the relevance of the first three operators. In the infrared we find trajectories that correspond to classical general relativity and further show non-classical behaviour in some fluctuation couplings. We also find signatures for the apparent convergence of the systematic vertex expansion. This opens a promising path towards establishing asymptotically safe gravity in terms of apparent convergence.

Using Medications Safely

MedlinePlus

... health systems play an important role in preventing medication errors. To make sure you use medicines safely and effectively, ASHP recommends that you: Keep a list of all medications that you take (prescribed drugs, nonprescription medicines, herbal ...

Integral Battery Power Limiting Circuit for Intrinsically Safe Applications

NASA Technical Reports Server (NTRS)

Burns, Bradley M.; Blalock, Norman N.

2010-01-01

A circuit topology has been designed to guarantee the output of intrinsically safe power for the operation of electrical devices in a hazardous environment. This design uses a MOSFET (metal oxide semiconductor field-effect transistor) as a switch to connect and disconnect power to a load. A test current is provided through a separate path to the load for monitoring by a comparator against a preset threshold level. The circuit is configured so that the test current will detect a fault in the load and open the switch before the main current can respond. The main current passes through the switch and then an inductor. When a fault occurs in the load, the current through the inductor cannot change immediately, but the voltage drops immediately to safe levels. The comparator detects this drop and opens the switch before the current in the inductor has a chance to respond. This circuit protects both the current and voltage from exceeding safe levels. Typically, this type of protection is accomplished by a fuse or a circuit breaker, but in order for a fuse or a circuit breaker to blow or trip, the current must exceed the safe levels momentarily, which may be just enough time to ignite anything in a hazardous environment. To prevent this from happening, a fuse is typically current-limited by the addition of the resistor to keep the current within safe levels while the fuse reacts. The use of a resistor is acceptable for non-battery applications where the wasted energy and voltage drop across the resistor can be tolerated. The use of the switch and inductor minimizes the wasted energy. For example, a circuit runs from a 3.6-V battery that must be current-limited to 200 mA. If the circuit normally draws 10 mA, then an 18-ohm resistor would drop 180 mV during normal operation, while a typical switch (0.02 ohm) and inductor (0.97 ohm) would only drop 9.9 mV. From a power standpoint, the current-limiting resistor protection circuit wastes about 18 times more power than the

Unmanned Aerial System (UAS) Traffic Management (UTM): Enabling Low-Altitude Airspace and UAS Operations

NASA Technical Reports Server (NTRS)

Kopardekar, Parimal H.

2014-01-01

Many civilian applications of Unmanned Aerial Systems (UAS) have been imagined ranging from remote to congested urban areas, including goods delivery, infrastructure surveillance, agricultural support, and medical services delivery. Further, these UAS will have different equipage and capabilities based on considerations such as affordability, and mission needs applications. Such heterogeneous UAS mix, along with operations such as general aviation, helicopters, gliders must be safely accommodated at lower altitudes. However, key infrastructure to enable and safely manage widespread use of low-altitude airspace and UAS operations therein does not exist. Therefore, NASA is exploring functional design, concept and technology development, and a prototype UAS Traffic Management (UTM) system. UTM will support safe and efficient UAS operations for the delivery of goods and services

Highway Maintenance Equipment Operator. Specialized Equipment. Training Materials.

ERIC Educational Resources Information Center

Perky, Sandra Dutreau; And Others

This curriculum guide provides instructional materials to assist in training equipment operators in the safe and effective use of highway maintenance equipment. It includes 18 units of instruction covering the large equipment used in maintenance operations. Each unit of instruction consists of eight basic components: performance objectives,…

Managing drugs safely.

PubMed

van den Anker, John N

2005-02-01

There is hard data to show that newborn infants are more likely than adults to experience adverse reactions to drugs. Paradoxically, drug-related legislation to ensure safe and effective drug use in humans neglected neonates until 2002, when the Best Pharmaceuticals Act for Children was signed into law in the USA. The situation for neonates should now catch up with that for adults and neonates will be prescribed more licensed drugs in the near future. If we are to be able to analyze the underlying system errors to improve the safe use of drugs in the studied patient population, reporting of adverse drug events and reactions needs to happen in a blame free environment. In addition, computerized physician order entry will certainly further improve the current situation by preventing errors in ordering, transcribing, verifying, and transmitting medication orders.

Inherently Safe Fission Power System for Lunar Outposts

NASA Astrophysics Data System (ADS)

Schriener, Timothy M.; El-Genk, Mohamed S.

2013-09-01

This paper presents the Solid Core-Sectored Compact Reactor (SC-SCoRe) and power system for future lunar outposts. The power system nominally provides 38 kWe continuously for 21 years, employs static components and has no single point failures in reactor cooling or power generation. The reactor core has six sectors, each has a separate pair of primary and secondary loops with liquid NaK-56 working fluid, thermoelectric (TE) power conversion and heat-pipes radiator panels. The electromagnetic (EM) pumps in the primary and secondary loops, powered with separate TE power units, ensure operation reliability and passive decay heat removal from the reactor after shutdown. The reactor poses no radiological concerns during launch, and remains sufficiently subcritical, with the radial reflector dissembled, when submerged in wet sand and the core flooded with seawater, following a launch abort accident. After 300 years of storage below grade on the Moon, the total radioactivity in the post-operation reactor drops below 164 Ci, a low enough radioactivity for a recovery and safe handling of the reactor.

Implicitly Coordinated Detect and Avoid Capability for Safe Autonomous Operation of Small UAS

NASA Technical Reports Server (NTRS)

Balachandran, Swee; Munoz, Cesar A.; Consiglio, Maria C.

2017-01-01

As the airspace becomes increasingly shared by autonomous small Unmanned Aerial Systems (UAS), there would be a pressing need for coordination strategies so that aircraft can safely and independently maneuver around obstacles, geofences, and traffic aircraft. Explicitly coordinating resolution strategies for small UAS would require additional components such as a reliable vehicle-to-vehicle communication infrastructure and standardized protocols for information exchange that could significantly increase the cost of deploying small UAS in a shared airspace. This paper explores a novel approach that enables multiple aircraft to implicitly coordinate their resolution maneuvers. By requiring all aircraft to execute the proposed approach deterministically, it is possible for all of them to implicitly agree on the region of airspace each will be occupying in a given time interval. The proposed approach lends itself to the construction of a suitable feedback mechanism that enables the real-time execution of an implicitly conflict-free path in a closed-loop manner dealing with uncertainties in aircraft speed. If a network infrastructure is available, the proposed approach can also exploit the benefits of explicit information.

An Automated Safe-to-Mate (ASTM) Tester

NASA Technical Reports Server (NTRS)

Nguyen, Phuc; Scott, Michelle; Leung, Alan; Lin, Michael; Johnson, Thomas

2013-01-01

Safe-to-mate testing is a common hardware safety practice where impedance measurements are made on unpowered hardware to verify isolation, continuity, or impedance between pins of an interface connector. A computer-based instrumentation solution has been developed to resolve issues. The ASTM is connected to the circuit under test, and can then quickly, safely, and reliably safe-to-mate the entire connector, or even multiple connectors, at the same time.

Studies on Various Functional Properties of Titania Thin Film Developed on Glazed Ceramic Wall Tiles

NASA Astrophysics Data System (ADS)

Anil, Asha; Darshana R, Bangoria; Misra, S. N.

A sol-gel based TiO2 thin film was applied on glazed wall tiles for studying its various functional properties. Thin film was deposited by spin coating on the substrate and subjected to curing at different temperatures such as 600°C, 650, 700°C, 750°C and 800°C with 10 minutes soaking. The gel powder was characterized by FTIR, DTA/TG and XRD. Microstructure of thin film was analyzed by FESEM and EDX. Surface properties of the coatings such as gloss, colour difference, stain resistance, mineral hardness and wettability were extensively studied. The antibacterial activity of the surface of coated substrate against E. coli was also examined. The durability of the coated substrate in comparison to the uncoated was tested against alkali in accordance with ISO: 10545 (Part 13):1995 standard. FESEM images showed that thin films are dense and homogeneous. Coated substrates after firing results in lustre with high gloss, which increased from 330 to 420 GU as the curing temperature increases compared to that of uncoated one (72 GU). Coated substrate cured at 800°C shows higher mineral hardness (5 Mohs’) compared to uncoated one (4 Mohs’) and films cured at all temperatures showed stain resistance. The experimental results showed that the resistance towards alkali attack increase with increase in curing temperature and alkali resistance of sample cured at 800 °C was found to be superior compared to uncoated substrate. Contact angle of water on coated surface of substrates decreased with increase in temperature. Bacterial reduction percentages of the coated surface was 97% for sample cured at 700°C and it decreased from 97% to 87% as the curing temperature increased to 800 °C when treated with E. coli bacteria.

Engineering approach for cost effective operation of industrial pump systems

NASA Astrophysics Data System (ADS)

Krickis, O.; Oleksijs, R.

2017-10-01

Power plants operators are persuaded to operate the main equipment such as centrifugal pumps in economically effective way. The operation of pump sets of district heating network at power plants should be done according to prescriptions of the original equipment manufacturer with further implementation of these requirements to distributed control system of the plant. In order to operate industrial pump sets with a small number of malfunctions is necessary to control the duty point of pump sets in H-Q coordinates, which could be complex task in some installations. Alternatively, pump operation control could be organized in H-n (head vs rpm) coordinates, utilizing pressure transmitters in pressure pipeline and value of rpm from variable speed driver. Safe operation range of the pump has to be limited with system parabolas, which prevents the duty point location outside of the predefined operation area. The particular study demonstrates the engineering approach for pump’s safe operation control development in MATLAB/Simulink environment, which allows to simulate the operation of the pump at different capacities in hydraulic system with variable characteristic and to predefine the conditions for efficient simultaneous pump operation in parallel connection.

Strategies for safe injections.

PubMed Central

Battersby, A.; Feilden, R.; Stoeckel, P.; Da Silva, A.; Nelson, C.; Bass, A.

1999-01-01

In 1998, faced with growing international concern, WHO set out an approach for achieving injection safety that encompassed all elements from patients' expectations and doctors' prescribing habits to waste disposal. This article follows that lead and describes the implications of the approach for two injection technologies: sterilizable and disposable. It argues that focusing on any single technology diverts attention from the more fundamental need for health services to develop their own comprehensive strategies for safe injections. National health authorities will only be able to ensure that injections are administered safely if they take an approach that encompasses the whole system, and choose injection technologies that fit their circumstances. PMID:10680247

So What's an RTG and Are They Safe?

NASA Technical Reports Server (NTRS)

Barret, Chris; Hughes, R. W. (Technical Monitor)

2001-01-01

When one considers space missions to the outer edges of our solar system and far beyond, our sun cannot be relied on to produce the required spacecraft (s/c) power. Solar energy diminishes as the square of the distance from the Sun. At Mars it is only 43% of that at earth. At Jupiter, it falls off to only 3.6% of Earth's. By the time we get out to Pluto, solar energy is only .066% what it is on Earth. Beyond the orbit of Mars, it is not practical to depend on solar power for a s/c. However, the farther out we go the more power we need to heat the s/c and to transmit data back to Earth over the long distances. On Earth, knowledge is power. In the outer solar system, power is knowledge. Solar arrays only operate at 19% efficiency, are very vulnerable to damage from radiation and temperature extremes, and cannot be used for even nearby missions that operate in extended darkness, or under the surface of a planet or moon. Twenty-six U.S. space missions, from the Transit to Cassini, have used radioisotope power systems and heater units to take s/c to the far reaches of our solar system and have demonstrated an outstanding record of safety and reliability. Radioisotope thermoelectric generators (RTG's) have proven to be safe, reliable, maintenance-free, and capable of providing both thermal and electrical power for decades under the harsh environments of deep space. RTG's have no problem operating in the high radiation belts of space, the extreme temperatures, or the severe dust storms of Mars, and they have proven to be the most reliable power source ever flown on U.S. s/c. For example, the two Pioneer s/c operated for more than two decades and the Voyager s/c may last for 40 years. RTG's are not nuclear reactors, they serve only as power generators and are not involved in the propulsion of the s/c. They operate on the principle of thermoelectric generation that converts heat directly into electricity, they have no moving parts, are extremely reliable, and have met or

Feeling safe during an inpatient hospitalization: a concept analysis.

PubMed

Mollon, Deene

2014-08-01

This paper aims to explore the critical attributes of the concept feeling safe. The safe delivery of care is a high priority; however; it is not really known what it means to the patient to 'feel safe' during an inpatient hospitalization. This analysis explores the topic of safety from the patient's perspective. Concept analysis. The data bases of CINAHL, Medline, PsychInfo and Google Scholar for the years 1995-2012 were searched using the terms safe and feeling safe. The eight-step concept analysis method of Walker and Avant was used to analyse the concept of feeling safe. Uses and defining attributes, as well as identified antecedents, consequences and empirical referents, are presented. Case examples are provided to assist in the understanding of defining attributes. Feeling safe is defined as an emotional state where perceptions of care contribute to a sense of security and freedom from harm. Four attributes were identified: trust, cared for, presence and knowledge. Relationship, environment and suffering are the antecedents of feeling safe, while control, hope and relaxed or calm are the consequences. Empirical referents and early development of a theory of feeling safe are explored. This analysis begins the work of synthesizing qualitative research already completed around the concept of feeling safe by defining the key attributes of the concept. Support for the importance of developing patient-centred models of care and creating positive environments where patients receive high-quality care and feel safe is provided. © 2014 John Wiley & Sons Ltd.

Tangential gunshot wound with MagSafe ammunition.

PubMed

Rapkiewicz, Amy V; Tamburri, Robert; Basoa, Mark E; Catanese, Charles A

2005-09-01

MagSafe ammunition is a type of unconventional prefragmented ammunition. A fatal tangential gunshot wound involving MagSafe ammunition is presented. The ammunition and wound characteristics are discussed.

Creating Safe Spaces for Music Learning

ERIC Educational Resources Information Center

Hendricks, Karin S.; Smith, Tawnya D.; Stanuch, Jennifer

2014-01-01

This article offers a practical model for fostering emotionally safe learning environments that instill in music students a positive sense of self-belief, freedom, and purpose. The authors examine the implications for music educators of creating effective learning environments and present recommendations for creating a safe space for learning,…

Asymptotically safe standard model extensions?

NASA Astrophysics Data System (ADS)

Pelaggi, Giulio Maria; Plascencia, Alexis D.; Salvio, Alberto; Sannino, Francesco; Smirnov, Juri; Strumia, Alessandro

2018-05-01

We consider theories with a large number NF of charged fermions and compute the renormalization group equations for the gauge, Yukawa and quartic couplings resummed at leading order in 1 /NF. We construct extensions of the standard model where SU(2) and/or SU(3) are asymptotically safe. When the same procedure is applied to the Abelian U(1) factor, we find that the Higgs quartic can not be made asymptotically safe and stay perturbative at the same time.

A Preliminary Review of English Proficiency and Safe Commercial Motor Vehicle Operation.

DOT National Transportation Integrated Search

2008-07-01

Under sponsorship from the U.S. Department of Transportation Federal Motor Carrier Safety Administration, Office of Bus and Truck Standards and Operations, the John A. Volpe National Transportation Systems Center performed a preliminary research stud...

Determination of influence factors and accident rates for the Armored Tractor/Safe Secure Trailer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Phillips, J.S.; Clauss, D.B.; Blower, D.F.

1994-04-01

Operating environments, such as road type, road location, and time of day, play an important role in the observed accident rates of heavy trucks used in general commerce. These same factors influence the accident rate of the Armored Tractor/Safe Secure Trailer (AT/SST) used by the Department of Energy to transport hazardous cargos within the continental United States. This report discusses the development of accident rate influence factors. These factors, based on heavy trucks used in general commerce, are used to modify the observed overall AT/SST accident rate to account for the different operating environments.

Are bariatric operations performed by residents safe and efficient?

PubMed

Major, Piotr; Wysocki, Michał; Dworak, Jadwiga; Pędziwiatr, Michał; Małczak, Piotr; Budzyński, Andrzej

2017-04-01

The growing need for surgeons who are educated and trained in bariatric surgery has raised many issues related to training in this field. This study was performed to evaluate the safety and efficacy of laparoscopic sleeve gastrectomy (SG) and laparoscopic Roux-en-Y gastric bypass (LRYGB) performed by doctors-in-training during their residency in general surgery. Tertiary referral university teaching hospital, Poland. We retrospectively analyzed the data of patients who underwent bariatric surgery. One group underwent surgery performed by at least third-year residents learning particular types of surgeries (trainee group), and the second group underwent surgeries performed by experienced bariatric surgeons (mentor group). The primary endpoint was the safety of the procedures. We analyzed factors related to the intraoperative and postoperative course. The secondary endpoint was long-term weight reduction. A lower body mass index (BMI), fewer co-morbidities, and preferably female sex were the selection criteria for patients in the trainee group. We enrolled 408 patients who met all inclusion criteria. Among them, 233 underwent SG and 175 underwent LRYGB. For both SG and LRYGB, the median maximum preoperative weight was significantly lower in the trainee than mentor group. We found no statistically significant differences in the demographic factors or co-morbidities between the 2 groups. The median duration of SG and LRYGB surgery was significantly longer in the trainee than mentor group. The median number of stapler firings during SG was significantly lower in the trainee than mentor group. The number of stapler firings during LRYGB did not differ between the 2 groups. The incidence of intraoperative difficulties, which were based on the operator's subjective opinion, was higher in the trainee than mentor group for both SG and LRYGB. However, intraoperative difficulties had no significant impact on the intraoperative complication rate or risk of perioperative

76 FR 30495 - National Safe Boating Week, 2011

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-25

... Safe Boating Week, 2011 By the President of the United States of America A Proclamation As Americans... to watergoers. National Safe Boating Week is an opportunity to highlight the importance of safety... can save lives. Each year for National Safe Boating Week, the United States Coast Guard partners with...

Non-destructive characterization of oriental porcelain glazes and blue underglaze pigments using μ-EDXRF, μ-Raman and VP-SEM

NASA Astrophysics Data System (ADS)

Coutinho, M. L.; Muralha, V. S. F.; Mirão, J.; Veiga, J. P.

2014-03-01

The study of ancient materials with recognized cultural and economic value is a challenge to scientists and conservators, since it is usually necessary an approach through non-destructive techniques. Difficulties in establishing a correct analytical strategy are often significantly increased by the lack of knowledge on manufacture technologies and raw materials employed combined with the diversity of decay processes that may have acted during the lifetime of the cultural artefacts. A non-destructive characterization was performed on the glaze and underglaze pigments from a group of Chinese porcelain shards dated from the late Ming Dynasty (1368-1644) excavated at the Monastery of Santa Clara- a- Velha in Coimbra (Portugal). Chemical analysis was performed using micro-energy dispersive X-ray fluorescence spectrometry (μ-EDXRF). Mineralogical characterization was achieved by Raman microscopy (μ-Raman) and observation of small-surface crystallization dark spots with a metallic lustre in areas with high pigment concentration was done by variable pressure scanning electron microscopy (VP-SEM). Cobalt aluminate was identified as the blue underglaze pigment and a comparison of blue and dark blue pigments was performed by the ratio of Co, Mn, and Fe oxides, indicating a compositional difference between the two blue tonalities. Manganese oxide compounds were also identified as colouring agents in dark blue areas and surface migration of manganese compounds was verified.

Remotely operated high pressure valve protects test personnel

NASA Technical Reports Server (NTRS)

Howland, B. T.

1967-01-01

High pressure valve used in testing certain spacecraft systems is safely opened and closed by a remotely stationed operator. The valve is self-regulating in that if the incoming pressure drops below a desired value the valve will automatically close, warning the operator that the testing pressure has dropped to an undesired level.

HiCAT Software Infrastructure: Safe hardware control with object oriented Python

NASA Astrophysics Data System (ADS)

Moriarty, Christopher; Brooks, Keira; Soummer, Remi

2018-01-01

High contrast imaging for Complex Aperture Telescopes (HiCAT) is a testbed designed to demonstrate coronagraphy and wavefront control for segmented on-axis space telescopes such as envisioned for LUVOIR. To limit the air movements in the testbed room, software interfaces for several different hardware components were developed to completely automate operations. When developing software interfaces for many different pieces of hardware, unhandled errors are commonplace and can prevent the software from properly closing a hardware resource. Some fragile components (e.g. deformable mirrors) can be permanently damaged because of this. We present an object oriented Python-based infrastructure to safely automate hardware control and optical experiments. Specifically, conducting high-contrast imaging experiments while monitoring humidity and power status along with graceful shutdown processes even for unexpected errors. Python contains a construct called a “context manager” that allows you define code to run when a resource is opened or closed. Context managers ensure that a resource is properly closed, even when unhandled errors occur. Harnessing the context manager design, we also use Python’s multiprocessing library to monitor humidity and power status without interrupting the experiment. Upon detecting a safety problem, the master process sends an event to the child process that triggers the context managers to gracefully close any open resources. This infrastructure allows us to queue up several experiments and safely operate the testbed without a human in the loop.

Safe injection practice among health care workers, Gharbiya, Egypt.

PubMed

Ismail, Nanees A; Aboul Ftouh, Aisha M; El Shoubary, Waleed H

2005-01-01

A cross-sectional study was conducted in 25 health care facilities in Gharbiya governorate to assess safe injection practices among health care workers (HCWs). Two questionnaires, one to collect information about administrative issues related to safe injection and the other to collect data about giving injections, exposure to needle stick injuries, hepatitis B vaccination status and safe injection training. Practices of injections were observed using a standardized checklist. The study revealed that there was lack of both national and local infection control policies and lack of most of the supplies needed for safe injection practices. Many safe practices were infrequent as proper needle manipulation before disposal (41%), safe needle disposal (47.5%), reuse of used syringe & needle (13.2%) and safe syringe disposal (0%). Exposure to needle stick injuries were common among the interviewed HCWs (66.2%) and hand washing was the common post exposure prophylaxis measure (63.4%). Only 11.3% of HCWs had full course hepatitis B vaccination. Infection control -including safe injections- training programs should be afforded to all HCWs.

Safe handling of antineoplastic drugs.

PubMed

Harrison, B R

1994-07-01

Managers should be aware of the hazardous properties of antineoplastic drugs and of the procedures and equipment commonly recommended to provide a safe working environment for employees, patients, and visitors. Compliance with the many published guidelines should help ensure passage of the inevitable Occupational Safety and Health Administration (OSHA) or Joint Commission inspection. Acute and chronic toxicities of the antineoplastic drugs, the potential for exposure in the workplace, and the basic guidelines for safe handling of these agents are reviewed.

SafeNet: a methodology for integrating general-purpose unsafe devices in safe-robot rehabilitation systems.

PubMed

Vicentini, Federico; Pedrocchi, Nicola; Malosio, Matteo; Molinari Tosatti, Lorenzo

2014-09-01

Robot-assisted neurorehabilitation often involves networked systems of sensors ("sensory rooms") and powerful devices in physical interaction with weak users. Safety is unquestionably a primary concern. Some lightweight robot platforms and devices designed on purpose include safety properties using redundant sensors or intrinsic safety design (e.g. compliance and backdrivability, limited exchange of energy). Nonetheless, the entire "sensory room" shall be required to be fail-safe and safely monitored as a system at large. Yet, sensor capabilities and control algorithms used in functional therapies require, in general, frequent updates or re-configurations, making a safety-grade release of such devices hardly sustainable in cost-effectiveness and development time. As such, promising integrated platforms for human-in-the-loop therapies could not find clinical application and manufacturing support because of lacking in the maintenance of global fail-safe properties. Under the general context of cross-machinery safety standards, the paper presents a methodology called SafeNet for helping in extending the safety rate of Human Robot Interaction (HRI) systems using unsafe components, including sensors and controllers. SafeNet considers, in fact, the robotic system as a device at large and applies the principles of functional safety (as in ISO 13489-1) through a set of architectural procedures and implementation rules. The enabled capability of monitoring a network of unsafe devices through redundant computational nodes, allows the usage of any custom sensors and algorithms, usually planned and assembled at therapy planning-time rather than at platform design-time. A case study is presented with an actual implementation of the proposed methodology. A specific architectural solution is applied to an example of robot-assisted upper-limb rehabilitation with online motion tracking. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

77 FR 31147 - National Safe Boating Week, 2012

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-24

... Safe Boating Week, 2012 By the President of the United States of America A Proclamation For generations... friends and family a well- loved tradition. During National Safe Boating Week, we renew our commitment to... mark National Safe Boating Week, let us reflect on that important mission and resolve to do our part to...

Petroleum Jelly: Safe for a Dry Nose?

MedlinePlus

... dryness. Is this safe? Answers from Lawrence E. Gibson, M.D. Petroleum jelly is generally safe to ... several hours of lying down. With Lawrence E. Gibson, M.D. Marchiori E, et al. Exogenous lipoid ...

Taking Medicines Safely: At Your Doctor's Office

MedlinePlus

... on. Feature: Taking Medicines Safely At Your Doctor's Office Past Issues / Summer 2013 Table of Contents Download ... Articles Medicines: Use Them Safely / At Your Doctor's Office / Ask Your Pharmacist / Now, It's Your Turn: How ...

Emergency end of life operations for CNES remote sensing satellites—Management and operational process

NASA Astrophysics Data System (ADS)

Bertrand, Régis; Alby, Fernand; Costes, Thierry; Dejoie, Joël; Delmas, Dominique-Roland; Delobette, Damien; Gibek, Isabelle; Gleyzes, Alain; Masson, Françoise; Meyer, Jean-Renaud; Moreau, Agathe; Perret, Lionel; Riclet, François; Ruiz, Hélène; Schiavon, Françoise; Spizzi, Pierre; Viallefont, Pierre; Villaret, Colette

2012-10-01

The French Space Agency (CNES) is currently operating thirteen satellites among which five remote sensing satellites. This fleet is composed of two civilian (SPOT) and three military (HELIOS) satellites and it has been recently completed by the first PLEIADES satellite which is devoted to both civil and military purposes. The CNES operation board decided to appoint a Working Group (WG) in order to anticipate and tackle issues related to the emergency End Of Life (EOL) operations due to unexpected on-board events affecting the satellite. This is of particular interest in the context of the French Law on Space Operations (LSO), entered in force on Dec. 2010, which states that any satellite operator must demonstrate its capability to control the space vehicle whatever the mission phase from the launch up to the EOL. Indeed, after several years in orbit the satellites may be affected by on-board anomalies which could damage the implementation of EOL operations, i.e. orbital manoeuvres or platform disposal. Even if automatic recovery actions ensure autonomous reconfigurations on redundant equipment, i.e. setting for instance the satellite into a safe mode, it is crucial to anticipate the consequences of failures of every equipment and functions necessary for the EOL operations. For this purpose, the WG has focused on each potential anomaly by analysing: its emergency level, as well as the EOL operations potentially inhibited by the failure and the needs of on-board software workarounds… The main contribution of the WG consisted in identifying a particular satellite configuration called "minimal Withdrawal From Service (WFS) configuration". This configuration corresponds to an operational status which involves a redundancy necessary for the EOL operations. Therefore as soon as a satellite reaches this state, a dedicated steering committee is activated and decides of the future of the satellite with respect to three options: a/. the satellite is considered safe and can

Implementation of Safe-by-Design for Nanomaterial Development and Safe Innovation: Why We Need a Comprehensive Approach

PubMed Central

Kraegeloh, Annette; Suarez-Merino, Blanca; Sluijters, Teun; Micheletti, Christian

2018-01-01

Manufactured nanomaterials (MNMs) are regarded as key components of innovations in various fields with high potential impact (e.g., energy generation and storage, electronics, photonics, diagnostics, theranostics, or drug delivery agents). Widespread use of MNMs raises concerns about their safety for humans and the environment, possibly limiting the impact of the nanotechnology-based innovation. The development of safe MNMs and nanoproducts has to result in a safe as well as functional material or product. Its safe use, and disposal at the end of its life cycle must be taken into account too. However, not all MNMs are similarly useful for all applications, some might bear a higher hazard potential than others, and use scenarios could lead to different exposure probabilities. To improve both safety and efficacy of nanotechnology, we think that a new proactive approach is necessary, based on pre-regulatory safety assessment and dialogue between stakeholders. On the basis of the work carried out in different European Union (EU) initiatives, developing and integrating MNMs Safe-by-Design and Trusted Environments (NANoREG, ProSafe, and NanoReg2), we present our point of view here. This concept, when fully developed, will allow for cost effective industrial innovation, and an exchange of key information between regulators and innovators. Regulators are thus informed about incoming innovations in good time, supporting a proactive regulatory action. The final goal is to contribute to the nanotechnology governance, having faster, cheaper, effective, and safer nano-products on the market. PMID:29661997

Implementation of Safe-by-Design for Nanomaterial Development and Safe Innovation: Why We Need a Comprehensive Approach.

PubMed

Kraegeloh, Annette; Suarez-Merino, Blanca; Sluijters, Teun; Micheletti, Christian

2018-04-14

Manufactured nanomaterials (MNMs) are regarded as key components of innovations in various fields with high potential impact (e.g., energy generation and storage, electronics, photonics, diagnostics, theranostics, or drug delivery agents). Widespread use of MNMs raises concerns about their safety for humans and the environment, possibly limiting the impact of the nanotechnology-based innovation. The development of safe MNMs and nanoproducts has to result in a safe as well as functional material or product. Its safe use, and disposal at the end of its life cycle must be taken into account too. However, not all MNMs are similarly useful for all applications, some might bear a higher hazard potential than others, and use scenarios could lead to different exposure probabilities. To improve both safety and efficacy of nanotechnology, we think that a new proactive approach is necessary, based on pre-regulatory safety assessment and dialogue between stakeholders. On the basis of the work carried out in different European Union (EU) initiatives, developing and integrating MNMs Safe-by-Design and Trusted Environments (NANoREG, ProSafe, and NanoReg2), we present our point of view here. This concept, when fully developed, will allow for cost effective industrial innovation, and an exchange of key information between regulators and innovators. Regulators are thus informed about incoming innovations in good time, supporting a proactive regulatory action. The final goal is to contribute to the nanotechnology governance, having faster, cheaper, effective, and safer nano-products on the market.

Environmentally safe fluid extractor

DOEpatents

Sungaila, Zenon F.

1993-01-01

An environmentally safe fluid extraction device for use in mobile laboratory and industrial settings comprising a pump, compressor, valving system, waste recovery tank, fluid tank, and a exhaust filtering system.

Environmentally safe fluid extractor

DOEpatents

Sungaila, Zenon F.

1993-07-06

An environmentally safe fluid extraction device for use in mobile laboratory and industrial settings comprising a pump, compressor, valving system, waste recovery tank, fluid tank, and a exhaust filtering system.

Results of 30 kWt Safe Affordable Fission Engine (SAFE-30) primary heat transport testing

NASA Astrophysics Data System (ADS)

Pedersen, Kevin; van Dyke, Melissa; Houts, Mike; Godfroy, Tom; Martin, James; Dickens, Ricky; Williams, Eric; Harper, Roger; Salvil, Pat; Reid, Bob

2001-02-01

The use of resistance heaters to simulate heat from fission allows extensive development of fission systems to be performed in non-nuclear test facilities, saving time and money. Resistance heated tests on the Safe Affordable Fission Engine-30 kilowatt (SAFE30) test article are being performed at the Marshall Space Flight Center. This paper discusses the results of these experiments to date, and describes the additional testing that will be performed. Recommendations related to the design of testable space fission power and propulsion systems are made. .

Examination of Frameworks for Safe Integration of Intelligent Small UAS into the NAS

NASA Technical Reports Server (NTRS)

Logan, Michael J.

2012-01-01

This paper discusses a proposed framework for the safe integration of small unmanned aerial systems (sUAS) into the National Airspace System (NAS). The paper briefly examines the potential uses of sUAS to build an understanding of the location and frequency of potential future flight operations based on the future applications of the sUAS systems. The paper then examines the types of systems that would be required to meet the application-level demand to determine "classes" of platforms and operations. A framework for categorization of the "intelligence" level of the UAS is postulated for purposes of NAS integration. Finally, constraints on the intelligent systems are postulated to ensure their ease of integration into the NAS.

Keeping Campuses Safe.

ERIC Educational Resources Information Center

Kennedy, Mike

1999-01-01

Describes how colleges and universities are using technology, as well as traditional methods, to keep campuses safe and reduce crime. Topics include using free pizza in a successful contest to teach students about campus safety, installing security cameras, using access-control cards, providing adequate lighting, and creating a bicycle patrol…

Safe Hazmat Storage Tips.

ERIC Educational Resources Information Center

Neville, Angela

1996-01-01

Provides a list of recommendations for safely managing hazardous waste containers. Encourages training of employees on the hazards of the wastes they handle and the correct procedures for managing containers. (DDR)

What Safe Zone? The Vast Majority of Dislocated THAs Are Within the Lewinnek Safe Zone for Acetabular Component Position.

PubMed

Abdel, Matthew P; von Roth, Philipp; Jennings, Matthew T; Hanssen, Arlen D; Pagnano, Mark W

2016-02-01

Numerous factors influence total hip arthroplasty (THA) stability including surgical approach and soft tissue tension, patient compliance, and component position. One long-held tenet regarding component position is that cup inclination and anteversion of 40° ± 10° and 15° ± 10°, respectively, represent a "safe zone" as defined by Lewinnek that minimizes dislocation after primary THA; however, it is clear that components positioned in this zone can and do dislocate. We sought to determine if these classic radiographic targets for cup inclination and anteversion accurately predicted a safe zone limiting dislocation in a contemporary THA practice. From a cohort of 9784 primary THAs performed between 2003 and 2012 at one institution, we retrospectively identified 206 THAs (2%) that subsequently dislocated. Radiographic parameters including inclination, anteversion, center of rotation, and limb length discrepancy were analyzed. Mean followup was 27 months (range, 0-133 months). The majority (58% [120 of 206]) of dislocated THAs had a socket within the Lewinnek safe zone. Mean cup inclination was 44° ± 8° with 84% within the safe zone for inclination. Mean anteversion was 15° ± 9° with 69% within the safe zone for anteversion. Sixty-five percent of dislocated THAs that were performed through a posterior approach had an acetabular component within the combined acetabular safe zones, whereas this was true for only 33% performed through an anterolateral approach. An acetabular component performed through a posterior approach was three times as likely to be within the combined acetabular safe zones (odds ratio [OR], 1.3; 95% confidence interval [CI], 1.1-1.6) than after an anterolateral approach (OR, 0.4; 95% CI, 0.2-0.7; p < 0.0001). In contrast, acetabular components performed through a posterior approach (OR, 1.6; 95% CI, 1.2-1.9) had an increased risk of dislocation compared with those performed through an anterolateral approach (OR, 0.8; 95% CI, 0.7-0.9; p

Airport surface operations requirements analysis

NASA Technical Reports Server (NTRS)

Groce, John L.; Vonbokern, Greg J.; Wray, Rick L.

1993-01-01

This report documents the results of the Airport Surface Operations Requirements Analysis (ASORA) study. This study was conducted in response to task 24 of NASA Contract NAS1-18027. This study is part of NASA LaRC's Low Visibility Surface Operations program, which is designed to eliminate the constraints on all-weather arrival/departure operations due to the airport/aircraft ground system. The goal of this program is to provide the capability for safe and efficient aircraft operations on the airport surface during low visibility conditions down to zero. The ASORA study objectives were to (1) develop requirements for operation on the airport surface in visibilities down to zero; (2) survey and evaluate likely technologies; (3) develop candidate concepts to meet the requirements; and (4) select the most suitable concept based on cost/benefit factors.

Contextual Challenges to Safe Surgery in a Resource-limited Setting: A Multicenter, Multiprofessional Qualitative Study.

PubMed

Scott, John W; Lin, Yihan; Ntakiyiruta, Georges; Mutabazi, Zeta A; Davis, William Austin; Morris, Megan A; Smink, Douglas S; Riviello, Robert; Yule, Steven

2018-03-01

Safe surgery should be available to all patients, no matter the setting. The purpose of this study was to explore the contextual-specific challenges to safe surgical care encountered by surgeons and surgical teams in many in low- and middle-income countries (LMICs), and to understand the ways in which surgical teams overcome them. Optimal surgical performance is highly complex and requires providers to integrate and communicate information regarding the patient, task, team, and environment to coordinate team-based care that is timely, effective, and safe. Resource limitations common to many LMICs present unique challenges to surgeons operating in these environments, but have never been formally described. Using a grounded theory approach, we interviewed 34 experienced providers (surgeons, anesthetists, and nurses) at the 4 tertiary referral centers in Rwanda, to understand the challenges to safe surgical care and strategies to overcome them. Interview transcripts were coded line-by-line and iteratively analyzed for emerging themes until thematic saturation was reached. Rwandan-described challenges related to 4 domains: physical resources, human resources, overall systems support, and communication/language. The majority of these challenges arose from significant variability in either the quantity or quality of these domains. Surgical providers exhibited examples of resilient strategies to anticipate, monitor, respond to, and learn from these challenges. Resource variability rather than lack of resources underlies many contextual challenges to safe surgical care in a LMIC setting. Understanding these challenges and resilient strategies to overcome them is critical for both LMIC surgical providers and surgeons from HICs working in similar settings.

Functional Requirements Document for HALE UAS Operations in the NAS: Step 1. Version 3

NASA Technical Reports Server (NTRS)

2006-01-01

The purpose of this Functional Requirements Document (FRD) is to compile the functional requirements needed to achieve the Access 5 Vision of "operating High Altitude, Long Endurance (HALE) Unmanned Aircraft Systems (UAS) routinely, safely, and reliably in the national airspace system (NAS)" for Step 1. These functional requirements could support the development of a minimum set of policies, procedures and standards by the Federal Aviation Administration (FAA) and various standards organizations. It is envisioned that this comprehensive body of work will enable the FAA to establish and approve regulations to govern safe operation of UAS in the NAS on a routine or daily "file and fly" basis. The approach used to derive the functional requirements found within this FRD was to decompose the operational requirements and objectives identified within the Access 5 Concept of Operations (CONOPS) into the functions needed to routinely and safely operate a HALE UAS in the NAS. As a result, four major functional areas evolved to enable routine and safe UAS operations for an on-demand basis in the NAS. These four major functions are: Aviate, Navigate, Communicate, and Avoid Hazards. All of the functional requirements within this document can be directly traceable to one of these four major functions. Some functions, however, are traceable to several, or even all, of these four major functions. These cross-cutting functional requirements support the "Command / Control: function as well as the "Manage Contingencies" function. The requirements associated to these high-level functions and all of their supporting low-level functions are addressed in subsequent sections of this document.

Safety considerations in the design and operation of large wind turbines

NASA Technical Reports Server (NTRS)

Reilly, D. H.

1979-01-01

The engineering and safety techniques used to assure the reliable and safe operation of large wind turbine generators utilizing the Mod 2 Wind Turbine System Program as an example is described. The techniques involve a careful definition of the wind turbine's natural and operating environments, use of proven structural design criteria and analysis techniques, an evaluation of potential failure modes and hazards, and use of a fail safe and redundant component engineering philosophy. The role of an effective quality assurance program, tailored to specific hardware criticality, and the checkout and validation program developed to assure system integrity are described.

Karate: Keep It Safe.

ERIC Educational Resources Information Center

Jordan, David

1981-01-01

Safety guidelines for each phase of a karate practice session are presented to provide an accident-free and safe environment for teaching karate in a physical education or traditional karate training program. (JMF)

Treatment of toe nail fungus infection using an AO Q-switched eye-safe erbium glass laser at 1534nm

NASA Astrophysics Data System (ADS)

Myers, Michael J.; Myers, Jeffrey A.; Roth, Franziska; Guo, Baoping; Hardy, Christopher R.; Myers, Sean; Carrabba, Angelo; Trywick, Carmen; Bryant, Stewart; Griswold, John Robert; Mazzochi, Aggie

2013-03-01

We report on "eye-safe" erbium glass laser operating at Short-Wave Infra-Red (SWIR) region at 1534nm, to treat Onychomycosis or toenail fungus. Infected toenails of 12 patients were treated over a 3 month period using both long pulse and Q-switched laser output pulses. Our results compared favorably to Neodymium Yittrium Aluminum Garnet (Nd:YAG) laser fungus treatment studies as reported in literature. Nd:YAG laser devices, operating in the Near Infra- Red, (NIR) region at 1064nm, have recently become an effective alternative treatment to traditional oral medications used to treat nail fungal infections. Conventional nail infection treatments employ medications such as allylamines, azoles and other classes of antifungal drugs that are unpopular due to numerous side-affects and drug interactions. Side effects of these drugs include headache, itching, loss of sense of taste, nausea, diarrhea, heart failure and even potential death from liver failure [1,2,3]. The effectiveness of conventional oral antifungal medications varies. In addition, antifungal prescription drugs are administered for long periods ranging from 6 weeks to 18 months. Nd:YAG antifungal laser treatment reports claim high success rates (65-95%) in eradicating toenail fungus and without adverse side-affects. Multiple laser treatments are administered over a 3 to 6 month period [4,5,6,7]. Our initial treatments performed with the Er:glass laser on toenail fungus patients required only 1 to 2 treatments for cure. This same SWIR laser was used in experiments to treat Athlete's Foot fungal infections. The 1534nm Er:glass laser emission has been found to be well optimized for dermatological treatments due high transmission properties of human skin in the SWIR region. Increased depth of tissue penetration is well

Review of "Successful, Safe, and Healthy Students"

ERIC Educational Resources Information Center

Glass, Gene V.; Barnett, Steven; Welner, Kevin G.

2010-01-01

The research summary "Successful, Safe, and Healthy Students" presents the research background for the Obama administration's proposals for comprehensive, community-wide services in high-poverty neighborhoods, extended learning time, family engagement and safe schools. While these policies have broad and common-sense appeal, the research…

Research on station management in subway operation safety

NASA Astrophysics Data System (ADS)

Li, Yiman

2017-10-01

The management of subway station is an important part of the safe operation of urban subway. In order to ensure the safety of subway operation, it is necessary to study the relevant factors that affect station management. In the protection of subway safety operations on the basis of improving the quality of service, to promote the sustained and healthy development of subway stations. This paper discusses the influencing factors of subway operation accident and station management, and analyzes the specific contents of station management security for subway operation, and develops effective suppression measures. It is desirable to improve the operational quality and safety factor for subway operations.

Cost effective launch operations of the SSME

NASA Technical Reports Server (NTRS)

Klatt, F. P.

1985-01-01

The Space Shuttle Main Engine (SSME) represents the beginning of reusable rocket engine operations in the space transportation system (STS). Steps taken to reduce the overall cost of flight operations of the SSME by improving turnaround operations, extending the life of the engine, and improving the cost effectiveness of overhaul operations at the Canoga Park home plant are described. Ground certification testing to ensure safe launch operations is described, as well as certification extension testing that leads to a service life equivalent to 40 flights. The proven flight record of the SSME, which has demonstrated the utility of the SSME as a key component of America's space transportation system, is discussed.

Taking multiple medicines safely

MedlinePlus

... medlineplus.gov/ency/patientinstructions/000883.htm Taking multiple medicines safely To use the sharing features on this ... directed. Why You May Need More Than One Medicine You may take more than one medicine to ...

Monitoring Moving Queries inside a Safe Region

PubMed Central

Al-Khalidi, Haidar; Taniar, David; Alamri, Sultan

2014-01-01

With mobile moving range queries, there is a need to recalculate the relevant surrounding objects of interest whenever the query moves. Therefore, monitoring the moving query is very costly. The safe region is one method that has been proposed to minimise the communication and computation cost of continuously monitoring a moving range query. Inside the safe region the set of objects of interest to the query do not change; thus there is no need to update the query while it is inside its safe region. However, when the query leaves its safe region the mobile device has to reevaluate the query, necessitating communication with the server. Knowing when and where the mobile device will leave a safe region is widely known as a difficult problem. To solve this problem, we propose a novel method to monitor the position of the query over time using a linear function based on the direction of the query obtained by periodic monitoring of its position. Periodic monitoring ensures that the query is aware of its location all the time. This method reduces the costs associated with communications in client-server architecture. Computational results show that our method is successful in handling moving query patterns. PMID:24696652

Safe speed limits for a safe system: The relationship between speed limit and fatal crash rate for different crash types.

PubMed

Doecke, Sam D; Kloeden, Craig N; Dutschke, Jeffrey K; Baldock, Matthew R J

2018-05-19

The objective of this article is to provide empirical evidence for safe speed limits that will meet the objectives of the Safe System by examining the relationship between speed limit and injury severity for different crash types, using police-reported crash data. Police-reported crashes from 2 Australian jurisdictions were used to calculate a fatal crash rate by speed limit and crash type. Example safe speed limits were defined using threshold risk levels. A positive exponential relationship between speed limit and fatality rate was found. For an example fatality rate threshold of 1 in 100 crashes it was found that safe speed limits are 40 km/h for pedestrian crashes; 50 km/h for head-on crashes; 60 km/h for hit fixed object crashes; 80 km/h for right angle, right turn, and left road/rollover crashes; and 110 km/h or more for rear-end crashes. The positive exponential relationship between speed limit and fatal crash rate is consistent with prior research into speed and crash risk. The results indicate that speed zones of 100 km/h or more only meet the objectives of the Safe System, with regard to fatal crashes, where all crash types except rear-end crashes are exceedingly rare, such as on a high standard restricted access highway with a safe roadside design.

Orbital operations study. Appendix A: Interactivity analysis

NASA Technical Reports Server (NTRS)

1972-01-01

Supplemental analyses conducted to verify that safe, feasible, design concepts exist for accomplishing the attendant interface activities of the orbital operations mission are presented. The data are primarily concerned with functions and concepts common to more than one of the interfacing activities or elements. Specific consideration is given to state vector update, payload deployment, communications links, jet plume impingement, attached element operations, docking and structural interface assessment, and propellant transfer.

Beth Reis and the Safe Schools Coalition

ERIC Educational Resources Information Center

Vaught, Sabina E.

2007-01-01

This article chronicles the formation and organization of the Safe Schools Coalition (SCC) through the experiences of Beth Reis, co-founder and co-Chair. The article suggests ways in which the SCC can serve as a model for both collective and individual work in promoting safe schools.

Criticality Safety Evaluation of the LLNL Inherently Safe Subcritical Assembly (ISSA)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Percher, Catherine

2012-06-19

The LLNL Nuclear Criticality Safety Division has developed a training center to illustrate criticality safety and reactor physics concepts through hands-on experimental training. The experimental assembly, the Inherently Safe Subcritical Assembly (ISSA), uses surplus highly enriched research reactor fuel configured in a water tank. The training activities will be conducted by LLNL following the requirements of an Integration Work Sheet (IWS) and associated Safety Plan. Students will be allowed to handle the fissile material under the supervision of LLNL instructors. This report provides the technical criticality safety basis for instructional operations with the ISSA experimental assembly.

OR.NET: a service-oriented architecture for safe and dynamic medical device interoperability.

PubMed

Kasparick, Martin; Schmitz, Malte; Andersen, Björn; Rockstroh, Max; Franke, Stefan; Schlichting, Stefan; Golatowski, Frank; Timmermann, Dirk

2018-02-23

Modern surgical departments are characterized by a high degree of automation supporting complex procedures. It recently became apparent that integrated operating rooms can improve the quality of care, simplify clinical workflows, and mitigate equipment-related incidents and human errors. Particularly using computer assistance based on data from integrated surgical devices is a promising opportunity. However, the lack of manufacturer-independent interoperability often prevents the deployment of collaborative assistive systems. The German flagship project OR.NET has therefore developed, implemented, validated, and standardized concepts for open medical device interoperability. This paper describes the universal OR.NET interoperability concept enabling a safe and dynamic manufacturer-independent interconnection of point-of-care (PoC) medical devices in the operating room and the whole clinic. It is based on a protocol specifically addressing the requirements of device-to-device communication, yet also provides solutions for connecting the clinical information technology (IT) infrastructure. We present the concept of a service-oriented medical device architecture (SOMDA) as well as an introduction to the technical specification implementing the SOMDA paradigm, currently being standardized within the IEEE 11073 service-oriented device connectivity (SDC) series. In addition, the Session concept is introduced as a key enabler for safe device interconnection in highly dynamic ensembles of networked medical devices; and finally, some security aspects of a SOMDA are discussed.

Supporting safe driving with arthritis: developing a driving toolkit for clinical practice and consumer use.

PubMed

Vrkljan, Brenda H; Cranney, Ann; Worswick, Julia; O'Donnell, Siobhan; Li, Linda C; Gélinas, Isabelle; Byszewski, Anna; Man-Son-Hing, Malcolm; Marshall, Shawn

2010-01-01

We conducted a series of focus groups to explore the information needs of clinicians and consumers related to arthritis and driving. An open coding analysis identified common themes across both consumer and clinician-based focus groups that underscored the importance of addressing driving-related concerns and the challenges associated with assessing safety. The results revealed that although driving is critical for maintaining independence and community mobility, drivers with arthritis experience several problems that can affect safe operation of a motor vehicle. Findings from this study are part of a broader research initiative that will inform the development of the Arthritis and Driving toolkit. This toolkit outlines strategies to support safe mobility for people with arthritis and will be an important resource in the coming years given the aging population.

Surgical management of early pregnancy failure: history, politics, and safe, cost-effective care.

PubMed

Harris, Lisa H; Dalton, Vanessa K; Johnson, Timothy R B

2007-05-01

Early pregnancy failure and induced abortion are often managed differently, even though safe uterine evacuation is the goal in both. Early pregnancy failure is commonly treated by curettage in operating room settings in anesthetized patients. Induced abortion is most commonly managed by office vacuum aspiration in awake or sedated patients. Medical evidence does not support routine operating room management of early pregnancy failure. This commentary reviews historical origins of these different care standards, explores political factors responsible for their perpetuation, and uses experience at University of Michigan to dramatize the ways in which history, politics, and biomedicine intersect to produce patient care. The University of Michigan initiated office uterine evacuations for early pregnancy failure treatment. Patients previously went to the operating room. These changes required faculty, staff, and resident education. Our efforts blurred the lines between spontaneous and induced abortion management, improved patient care and better utilized hospital resources.

Virus Alert: Ten Steps to Safe Computing.

ERIC Educational Resources Information Center

Gunter, Glenda A.

1997-01-01

Discusses computer viruses and explains how to detect them; discusses virus protection and the need to update antivirus software; and offers 10 safe computing tips, including scanning floppy disks and commercial software, how to safely download files from the Internet, avoiding pirated software copies, and backing up files. (LRW)

16 CFR 312.11 - Safe harbor programs.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 16 Commercial Practices 1 2014-01-01 2014-01-01 false Safe harbor programs. 312.11 Section 312.11 Commercial Practices FEDERAL TRADE COMMISSION REGULATIONS UNDER SPECIFIC ACTS OF CONGRESS CHILDREN'S ONLINE PRIVACY PROTECTION RULE § 312.11 Safe harbor programs. (a) In general. Industry groups or other persons...

Safe Sleep for Babies

MedlinePlus

... Every year, there are thousands of sleep-related deaths among babies. View large image and text description ... 2AZh9Bn Supporting research to better understand sleep-related deaths and strategies to improve safe sleep practices. Healthcare ...

Design and installation package for the Sunmat Flat Plate solar collector

NASA Technical Reports Server (NTRS)

1978-01-01

The information used in evaluating the design of a liquid flat plate solar collector is reported. Included in this package are subsystem performance specification, installation, operation and maintenance manuals, collector sizing guides, and detailed drawings of the single-glazed collector.

Solar collector apparatus having increased energy rejection during stagnation

DOEpatents

Moore, S.W.

1981-01-16

An active solar collector having increased energy rejection during stagnation is disclosed. The collector's glazing is brought into substantial contact with absorber during stagnation to increase re-emittance and thereby to maintan lower temperatures when the collector is not in operation.

Infrastructure-Based Sensors Augmenting Efficient Autonomous Vehicle Operations: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jun, Myungsoo; Markel, Anthony J

Autonomous vehicle technology development relies on an on-board network of fused sensor inputs for safe and efficient operation. The fused sensors offer multiple perspectives of similar information aiding in system decision robustness. The high cost of full systems on individual vehicles is seen as a potential barrier to broad adoption and achieving system energy efficiency gains. Since traffic in autonomous vehicle technology development relies on an on-board network of fused sensor inputs for safe and efficient operation. The fused sensors offer multiple perspectives of similar information aiding in system decision robustness. The high cost of full systems on individual vehiclesmore » is seen as a potential barrier to broad adoption and achieving system energy efficiency gains.« less

Vapor-Compression Heat Pumps for Operation Aboard Spacecraft

NASA Technical Reports Server (NTRS)

Ruemmele, Warren; Ungar, Eugene; Cornwell, John

2006-01-01

Vapor-compression heat pumps (including both refrigerators and heat pumps) of a proposed type would be capable of operating in microgravity and would be safe to use in enclosed environments like those of spacecraft. The designs of these pumps would incorporate modifications of, and additions to, vapor-compression cycles of heat pumps now used in normal Earth gravitation, in order to ensure efficiency and reliability during all phases of operation, including startup, shutdown, nominal continuous operation, and peak operation. Features of such a design might include any or all of the following: (1) Configuring the compressor, condenser, evaporator, valves, capillary tubes (if any), and controls to function in microgravitation; (2) Selection of a working fluid that satisfies thermodynamic requirements and is safe to use in a closed crew compartment; (3) Incorporation of a solenoid valve and/or a check valve to prevent influx of liquid to the compressor upon startup (such influx could damage the compressor); (4) Use of a diode heat pipe between the cold volume and the evaporator to limit the influx of liquid to the compressor upon startup; and (5) Use of a heated block to vaporize any liquid that arrives at the compressor inlet.

12 CFR 350.11 - Safe harbor provision.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 12 Banks and Banking 4 2010-01-01 2010-01-01 false Safe harbor provision. 350.11 Section 350.11 Banks and Banking FEDERAL DEPOSIT INSURANCE CORPORATION REGULATIONS AND STATEMENTS OF GENERAL POLICY DISCLOSURE OF FINANCIAL AND OTHER INFORMATION BY FDIC-INSURED STATE NONMEMBER BANKS § 350.11 Safe harbor...

Prospective study of glove perforation in obstetrical and gynecological operations: are we safe enough?

PubMed

Malhotra, Monika; Sharma, Jai Bhagwan; Wadhwa, Leena; Arora, Raksha

2004-08-01

To assess the glove perforation rate, efficacy of double gloving, effect of duration of surgery, expertise of surgeon and operative urgency on the glove perforation rate in obstetrical and gynecologic operations. From February to September 2002, double glove protocol was made necessary for all major obstetrical and gynecologic procedures. The operating surgeon, first and second assistant were included in the study. Gloves damage was noted (overt by inspection, occult by hydroinsufflation technique). Of the 156 procedures included in study, 32 procedures were performed (all emergency operations) single-gloved because surgeons found double gloving clumsy (56%), made it difficult to tie knots due to lack of dexterity (24%), or were too tight (20%). One thousand one hundred and twenty single gloves were examined after each procedure by hydroinsufflation. The overall perforation rate was 13.6% (single versus double outer gloves, 13.8% versus l3.2%, P > 0.05). Matching perforations were found in six cases (4.6%). Thus, the protection offered by double gloves was 95.4% even if the outer gloves were perforated. Four inner gloves had preexisting perforations. Sixty unused gloves checked similarly revealed a perforation rate of 1.6%. Emergency cases had higher perforation rate compared to elective surgeries (16.6% versus 10.8%, P < 0.00 1). Surgeries lasting for more than 40 min had a higher perforation rate compared to those finished in less than or equal to 40 min (18.6% versus 7.6%, P < 0.001). The middle finger of the left hand was the most commonly involved. The surgeon, first assistant and second assistant were involved in 73.6, 23.3 and 3.2% cases, respectively. Double gloving offers considerable protection against exposure to contaminants in the blood and body fluids of the patient and should be made routine, especially in developing countries where HIV, hepatitis B and C are widely prevalent. Double gloving should be made mandatory in emergency procedures, which

Approaching Suspicious Substances Safely

NASA Technical Reports Server (NTRS)

2004-01-01

A mineral identification tool that was developed for NASA's Mars Rover Technology Development program is now serving as a powerful tool for U.S. law enforcement agencies and military personnel to identify suspicious liquid and solid substances. The tool can measure unknown substances through glass and plastic packaging materials with the RamanProbe(TradeMark) focused fiber-optic probe. The probe length can be extended up to 200 meters to enable users to analyze potentially dangerous substances at a safe distance. In many cases, the spectrometer and personnel are kept in a safe zone while the probe is positioned next to the sample being analyzed. Being able to identify chemicals in remote locations also saves users time and labor, since otherwise the samples would need to be collected, transported, and prepared prior to measurement in the laboratory.

Design and performance evaluation of collision protection-based safety operation for a haptic robot-assisted catheter operating system.

PubMed

Zhang, Linshuai; Guo, Shuxiang; Yu, Huadong; Song, Yu; Tamiya, Takashi; Hirata, Hideyuki; Ishihara, Hidenori

2018-02-23

The robot-assisted catheter system can increase operating distance thus preventing the exposure radiation of the surgeon to X-ray for endovascular catheterization. However, few designs have considered the collision protection between the catheter tip and the vessel wall. This paper presents a novel catheter operating system based on tissue protection to prevent vessel puncture caused by collision. The integrated haptic interface not only allows the operator to feel the real force feedback, but also combines with the newly proposed collision protection mechanism (CPM) to mitigate the collision trauma. The CPM can release the catheter quickly when the measured force exceeds a certain threshold, so as to avoid the vessel puncture. A significant advantage is that the proposed mechanism can adjust the protection threshold in real time by the current according to the actual characteristics of the blood vessel. To verify the effectiveness of the tissue protection by the system, the evaluation experiments in vitro were carried out. The results show that the further collision damage can be effectively prevented by the CPM, which implies the realization of relative safe catheterization. This research provides some insights into the functional improvements of safe and reliable robot-assisted catheter systems.

Recent Enhancements to the National Transonic Facility (Mixed Mode Operations)

NASA Technical Reports Server (NTRS)

Kilgore, W. Allen; Chan, David; Balakrishna, S.; Wahls, Richard A.

2006-01-01

The U.S. National Transonic Facility continues to make enhancements to provide quality data in a safe, efficient and cost effective method for aerodynamic ground testing. Recent enhancements discussed in this paper include the development of a Mixed-mode of operations that combine Air-mode operations with Nitrogen-mode operations. This implementation and operational results of this new Mixed-mode expands the ambient temperature transonic region of testing beyond the Air-mode limitations at a significantly reduced cost over Nitrogen Mode operation.

Safe Surgery for All: Early Lessons from Implementing a National Government-Driven Surgical Plan in Ethiopia.

PubMed

Burssa, Daniel; Teshome, Atlibachew; Iverson, Katherine; Ahearn, Olivia; Ashengo, Tigistu; Barash, David; Barringer, Erin; Citron, Isabelle; Garringer, Kaya; McKitrick, Victoria; Meara, John; Mengistu, Abraham; Mukhopadhyay, Swagoto; Reynolds, Cheri; Shrime, Mark; Varghese, Asha; Esseye, Samson; Bekele, Abebe

2017-12-01

Recognizing the unmet need for surgical care in Ethiopia, the Federal Ministry of Health (FMOH) has pioneered innovative methodologies for surgical system development with Saving Lives through Safe Surgery (SaLTS). SaLTS is a national flagship initiative designed to improve access to safe, essential and emergency surgical and anaesthesia care across all levels of the healthcare system. Sustained commitment from the FMOH and their recruitment of implementing partners has led to notable accomplishments across the breadth of the surgical system, including but not limited to: (1) Leadership, management and governance-a nationally scaled surgical leadership and mentorship programme, (2) Infrastructure-operating room construction and oxygen delivery plan, (3) Supplies and logistics-a national essential surgical procedure and equipment list, (4) Human resource development-a Surgical Workforce Expansion Plan and Anaesthesia National Roadmap, (5) Advocacy and partnership-strong FMOH partnership with international organizations, including GE Foundation's SafeSurgery2020 initiative, (6) Innovation-facility-driven identification of problems and solutions, (7) Quality of surgical and anaesthesia care service delivery-a national peri-operative guideline and WHO Surgical Safety Checklist implementation, and (8) Monitoring and evaluation-a comprehensive plan for short-term and long-term assessment of surgical quality and capacity. As Ethiopia progresses with its commitment to prioritize surgery within its Health Sector Transformation Plan, disseminating the process and outcomes of the SaLTS initiative will inform other countries on successful national implementation strategies. The following article describes the process by which the Ethiopian FMOH established surgical system reform and the preliminary results of implementation across these eight pillars.

Somatotype, the risk of hydroxychloroquine retinopathy, and safe daily dosing guidelines.

PubMed

Browning, David J; Lee, Chong

2018-01-01

The aim of this study was to determine whether somatotype influences the risk of hydroxychloroquine (HC) retinopathy (HCR) and whether dosing by real body weight (RBW), ideal body weight (IBW), or the lesser of these better predicts the risk of HCR. A total of 565 patients taking HC for whom height and weight were recorded and a sensitive ancillary testing modality was used including 10-2 visual fields, spectral domain optical coherence tomography, fundus autofluorescence imaging, and multifocal electroretinography were enrolled. Body mass index (BMI) was compared for patients without and with HCR. Logistic regression models of age, cumulative dose, and daily dosing based on RBW, IBW, or lesser of these were compared. Area under the curve (AUC) of receiver operating characteristic plots was used to assess the diagnostic accuracy of RBW, IBW, and lesser of these guidelines for safe dosing. Probability plots for the risk of retinopathy versus BMI were compared for the different recommended guidelines on safe dosing. A total of 41 patients had HCR. The median BMI was 27.6 (interquartile range [IQR] 24.3, 32.6) and 24.0 (IQR 21.0, 31.6) for patients without and with HCR ( P =0.0102), respectively. AUC for univariate receiver operating characteristic plots of retinopathy versus dosing by RBW, IBW, and lesser of these was 0.71, 0.72, and 0.76, respectively. AUC for multivariate receiver operating characteristic plots of retinopathy versus models incorporating gender, age, cumulative dose, and BMI and differing by including dosing by RBW, IBW, and lesser of these was 0.82, 0.82, and 0.83, respectively. For all of the multivariate logistic models, the risk of retinopathy was higher for lower BMIs. Short, asthenic women are at higher risk for HCR. The 2011 American Academy of Ophthalmology (AAO) guidelines are safer for short, obese women. The 2016 AAO guidelines are safer for short, asthenic patients. Choosing daily dosing based on the lesser of the RBW and IBW guidelines

Investigation into legislative action needed to accommodate the future safe operation of autonomous vehicles in the state of Louisiana [tech summary].

DOT National Transportation Integrated Search

2016-10-01

The objective of this study is to review the status quo in the development of autonomous vehicles and determine : what regulatory action needs to be taken that will permit their safe introduction in : Louisiana while not stifling innovation and devel...

Safe Haven Laws as "Crime Control Theater"

ERIC Educational Resources Information Center

Hammond, Michelle; Miller, Monica K.; Griffin, Timothy

2010-01-01

Objectives: This article examines safe haven laws, which allow parents to legally abandon their infants. The main objective is to determine whether safe haven laws fit the criteria of "crime control theater", a term used to describe public policies that produce the appearance, but not the effect, of crime control, and as such are essentially…

Sun Safe Mode Controller Design for LADEE

NASA Technical Reports Server (NTRS)

Fusco, Jesse C.; Swei, Sean S. M.; Nakamura, Robert H.

2015-01-01

This paper presents the development of sun safe controllers which are designed to keep the spacecraft power positive and thermally balanced in the event an anomaly is detected. Employed by NASA's Lunar Atmosphere and Dust Environment Explorer (LADEE), the controllers utilize the measured sun vector and the spacecraft body rates for feedback control. To improve the accuracy of sun vector estimation, the least square minimization approach is applied to process the sensor data, which is proven to be effective and accurate. To validate the controllers, the LADEE spacecraft model engaging the sun safe mode was first simulated and then compared with the actual LADEE orbital fight data. The results demonstrated the applicability of the proposed sun safe controllers.

NHQ_2017_0086_Expedition 50 Crew Lands Safely in Kazakhstan to Complete Six-Month Mission

NASA Image and Video Library

2017-04-10

Expedition 50 Commander Shane Kimbrough of NASA and Soyuz Commander Sergey Ryzhikov and Flight Engineer Andrey Borisenko of Roscosmos landed safely near the town of Dzhezkazgan, Kazakhstan April 10 after bidding farewell to their colleagues on the complex and undocking their Soyuz MS-02 spacecraft from the Poisk Module on the International Space Station. The trio spent 173 days in space conducting research and operational work in support of the station.

Safe Maritime Autonomous Path Planning in a High Sea State

NASA Technical Reports Server (NTRS)

Ono, Masahiro; Quadrelli, Marco; Huntsberger, Terrance L.

2014-01-01

This paper presents a path planning method for sea surface vehicles that prevents capsizing and bow-diving in a high sea-state. A key idea is to use response amplitude operators (RAOs) or, in control terminology, the transfer functions from a sea state to a vessel's motion, in order to find a set of speeds and headings that results in excessive pitch and roll oscillations. This information is translated to arithmetic constraints on the ship's velocity, which are passed to a model predictive control (MPC)-based path planner to find a safe and optimal path that achieves specified goals. An obstacle avoidance capability is also added to the path planner. The proposed method is demonstrated by simulations.

Working with Self-Injurious Adolescents Using the Safe Kit

ERIC Educational Resources Information Center

Moyer, Michael

2008-01-01

This article offers a guide for using the Safe Kit when working with clients who self-injure. The Safe Kit can be used as a supplement to more traditional approaches to counseling and offers clients alternatives to self-injury when they need alternatives the most. The Safe Kit works under the assumption that individuals differ in the meaning they…

National CPS Certification | A Program of Safe Kids Worldwide

Science.gov Websites

the Tech! ABOUT THE PROGRAM National CPS Certification Training is a program of Safe Kids Worldwide ; E-Vouchers FAQS/HELP FAQs Fees Forms Policies & Procedures Who We Are NHTSA Safe Kids CPS-board State Farm Follow us on Facebook Copyright © 2017 by Safe Kids Worldwide - Child Passenger Safety

The Challenge of Providing Safe Water with an Intermittently Supplied Piped Water Distribution System

NASA Astrophysics Data System (ADS)

Kumpel, E.; Nelson, K. L.

2012-12-01

An increasing number of urban residents in low- and middle-income countries have access to piped water; however, this water is often not available continuously. 84% of reporting utilities in low-income countries provide piped water for fewer than 24 hours per day (van den Berg and Danilenko, 2010), while no major city in India has continuous piped water supply. Intermittent water supply leaves pipes vulnerable to contamination and forces households to store water or rely on alternative unsafe sources, posing a health threat to consumers. In these systems, pipes are empty for long periods of time and experience low or negative pressure even when water is being supplied, leaving them susceptible to intrusion from sewage, soil, or groundwater. Households with a non-continuous supply must collect and store water, presenting more opportunities for recontamination. Upgrading to a continuous water supply, while an obvious solution to these challenges, is currently out of reach for many resource-constrained utilities. Despite its widespread prevalence, there are few data on the mechanisms causing contamination in an intermittent supply and the frequency with which it occurs. Understanding the impact of intermittent operation on water quality can lead to strategies to improve access to safe piped water for the millions of people currently served by these systems. We collected over 100 hours of continuous measurements of pressure and physico-chemical water quality indicators and tested over 1,000 grab samples for indicator bacteria over 14 months throughout the distribution system in Hubli-Dharwad, India. This data set is used to explore and explain the mechanisms influencing water quality when piped water is provided for a few hours every 3-5 days. These data indicate that contamination occurs along the distribution system as water travels from the treatment plant to reservoirs and through intermittently supplied pipes to household storage containers, while real

Safe Haven Laws and School Social Work

ERIC Educational Resources Information Center

Kopels, Sandra

2012-01-01

"Safe haven" laws are designed to protect infants from being killed or otherwise harmed. This article examines the safe haven laws from the states that comprise the Midwest School Social Work Council and the variations between these laws regarding the age of the infant, where the infant can be left, who is allowed to leave the infant, whether…

Ethylene oxide sterilisation--is it safe?

PubMed Central

Gillespie, E H; Jackson, J M; Owen, G R

1979-01-01

Tests show that ethylene oxide penetrates and can sterilise long narrow tubes in a hospital ethylene oxide steriliser. Residual ethylene oxide levels in plastic tubing after sterilisation have been estimated. Although initially the levels were very high, storage for four days at room temperature reduced them to a safe level. If adequate controls of the sterilising process and storage are carried out, sterilisation by ethylene oxide is considered to be safe for new plastics and clean equipment. Images Figure PMID:512032

49 CFR 232.107 - Air source requirements and cold weather operations.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 4 2011-10-01 2011-10-01 false Air source requirements and cold weather... source requirements and cold weather operations. (a) Monitoring plans for yard air sources. (1) A... to the equipment and territory of that railroad to cover safe train operations during cold weather...