Science.gov

Sample records for safety plan hasp

  1. Tank farm health and safety plan. Revision 2

    SciTech Connect

    Mickle, G.D.

    1995-03-29

    This Tank Farm Health and Safety Plan (HASP) for the conduct of all operations and work activities at the Hanford Site 200 Area Tank Farms is provided in order to minimize health and safety risks to workers and other onsite personnel. The HASP accomplishes this objective by establishing requirements, providing general guidelines, and conveying farm and facility-specific hazard communication information. The HASP, in conjunction with the job-specific information required by the HASP, is provided also as a reference for use during the planning of work activities at the tank farms. This HASP applies to Westinghouse Hanford Company (WHC), other prime contractors to the U.S. Department of Energy (DOE), and subcontractors to WHC who may be involved in tank farm work activities. This plan is intended to be both a requirements document and a useful reference to aid tank farm workers in understanding the safety and health issues that are encountered in routine and nonroutine work activities. The HASP defines the health and safety responsibilities of personnel working at the tank farms. It has been prepared in recognition of and is consistent with National Institute of Safety and Health (NIOSH), and Occupational Safety and Health Administration (OSHA)/Unlimited State Coast Guard (USCG)/U.S. Environmental Protection Agency (EPA), Occupational Safety and Health Guidance Manual for Hazardous Waste Site Activities (NIOSH 1985); WHC-CM-4-3, Industrial Safety Manual, Volume 4, {open_quotes}Health and Safety Programs for Hazardous Waste Operations;{close_quotes} 29 CFR 1910.120, Hazardous Waste Operations and Emergency Response; WHC-CM-1-1, Management Policies; and WHC-CM-1-3, Management Requirements and Procedures. When differences in governing regulations or policies exist, the more stringent requirements shall apply until the discrepancy can be resolved.

  2. Developing a health and safety plan for hazardous field work in remote areas.

    PubMed

    Gochfeld, Michael; Volz, Conrad D; Burger, Joanna; Jewett, Stephen; Powers, Charles W; Friedlander, Barry

    2006-12-01

    Developing health and safety plans (HASPs) is a common feature of occupational safety and health for many workplaces. Formal HASPs are a requirement for hazardous waste work, requiring the anticipation and identification of hazards and embodying the training, equipping, and evaluation of workers. Aside from OSHA, there are relatively few manuals or examples and virtually no papers that provide practical guidance in what a HASP should cover or how to create and implement one. Moreover, existing guidance refers to spatially circumscribed worksites. This article details development of a HASP to cover field researchers and ship personnel conducting scientific research in a remote area of the world (Amchitka Island in the western Aleutians), hundreds of kilometers from the nearest emergency room. It required characterizing the kinds of work to be performed and anticipating the hazards that could be encountered. It illustrates the meshing of a general HASP with a ship safety plan, a dive safety plan, and specialized topics, including stop-work authority, rock climbing, firearms, vehicle safety, and communication strategy. Remote area operations are a growing challenge facing the profession. An expedition of this sort requires extensive planning and experienced safety personnel and cannot rely on luck to ensure the safe return of participants.

  3. Environmental Management Waste Management Facility (EMWMF) Site-Specific Health and Safety Plan, Oak Ridge, Tennessee

    SciTech Connect

    Flynn, N.C. Bechtel Jacobs

    2008-04-21

    The Bechtel Jacobs Company LLC (BJC) policy is to provide a safe and healthy workplace for all employees and subcontractors. The implementation of this policy requires that operations of the Environmental Management Waste Management Facility (EMWMF), located one-half mile west of the U.S. Department of Energy (DOE) Y-12 National Security Complex, be guided by an overall plan and consistent proactive approach to environment, safety and health (ES&H) issues. The BJC governing document for worker safety and health, BJC/OR-1745, 'Worker Safety and Health Program', describes the key elements of the BJC Safety and Industrial Hygiene (IH) programs, which includes the requirement for development and implementation of a site-specific Health and Safety Plan (HASP) where required by regulation (refer also to BJC-EH-1012, 'Development and Approval of Safety and Health Plans'). BJC/OR-1745, 'Worker Safety and Health Program', implements the requirements for worker protection contained in Title 10 Code of Federal Regulations (CFR) Part 851. The EMWMF site-specific HASP requirements identifies safe operating procedures, work controls, personal protective equipment, roles and responsibilities, potential site hazards and control measures, site access requirements, frequency and types of monitoring, site work areas, decontamination procedures, and outlines emergency response actions. This HASP will be available on site for use by all workers, management and supervisors, oversight personnel and visitors. All EMWMF assigned personnel will be briefed on the contents of this HASP and will be required to follow the procedures and protocols as specified. The policies and procedures referenced in this HASP apply to all EMWMF operations activities. In addition the HASP establishes ES&H criteria for the day-to-day activities to prevent or minimize any adverse effect on the environment and personnel safety and health and to meet standards that define acceptable waste management practices. The

  4. WAG 2 remedial investigation and site investigation site-specific work plan/health and safety checklist for the sediment transport modeling task

    SciTech Connect

    Holt, V.L.; Baron, L.A.

    1994-05-01

    This site-specific Work Plan/Health and Safety Checklist (WP/HSC) is a supplement to the general health and safety plan (HASP) for Waste Area Grouping (WAG) 2 remedial investigation and site investigation (WAG 2 RI&SI) activities [Health and Safety Plan for the Remedial Investigation and Site Investigation of Waste Area Grouping 2 at the Oak Ridge National Laboratory, Oak Ridge, Tennessee (ORNL/ER-169)] and provides specific details and requirements for the WAG 2 RI&SI Sediment Transport Modeling Task. This WP/HSC identifies specific site operations, site hazards, and any recommendations by Oak Ridge National Laboratory (ORNL) health and safety organizations [i.e., Industrial Hygiene (IH), Health Physics (HP), and/or Industrial Safety] that would contribute to the safe completion of the WAG 2 RI&SI. Together, the general HASP for the WAG 2 RI&SI (ORNL/ER-169) and the completed site-specific WP/HSC meet the health and safety planning requirements specified by 29 CFR 1910.120 and the ORNL Hazardous Waste Operations and Emergency Response (HAZWOPER) Program Manual. In addition to the health and safety information provided in the general HASP for the WAG 2 RI&SI, details concerning the site-specific task are elaborated in this site-specific WP/HSC, and both documents, as well as all pertinent procedures referenced therein, will be reviewed by all field personnel prior to beginning operations.

  5. Health and safety plan for phase II of the Bear Creek Valley treatability study Oak Ridge Y-12 plant, Oak Ridge, Tennessee

    SciTech Connect

    1997-05-01

    This Health and Safety Plan (HASP) addresses the health and safety (H&S) concerns and requirements for the Bear Creek Valley (BCV) Treatability Study at the Oak Ridge Y-12 Plant. Samples will be collected from effluent following treatment tests of extraction columns, algal mats, and mature wetlands supplied by surface water locations and existing groundwater monitoring well locations. The project Sampling and Analysis Plan addresses the project description, technical objectives, procedures, and planned work activities in greater detail. It is the responsibility of the project managers, field manager, and site health and safety officer (SHSO) to determine that the requirements of this HASP are sufficiently protective. If it is determined that the requirements of this HASP are not sufficiently protective, a field change order(s) (FCO) will be prepared. FCOs will include a completed job hazard analysis or similar worksheet to ensure complete hazard assessment. FCOs must be approved by the Environmental Management and Enrichment Facilities (EMEF) project manager, EMEF H&S manager, subcontractor project or field manager, and subcontractor H&S representative. As a minimum, FCOs will be prepared if additional tasks will be performed or if contaminant exposure is anticipated.

  6. TWRS safety program plan

    SciTech Connect

    Calderon, L.M., Westinghouse Hanford

    1996-08-01

    Management of Nuclear Safety, Industrial Safety, Industrial Hygiene, and Fire Protection programs, functions, and field support resources for Tank Waste Remediation Systems (TWRS) has, until recently, been centralized in TWRS Safety, under the Emergency, Safety, and Quality organization. Industrial hygiene technician services were also provided to support operational needs related to safety basis compliance. Due to WHC decentralization of safety and reengineering efforts in West Tank Farms, staffing and safety responsibilities have been transferred to the facilities. Under the new structure, safety personnel for TWRS are assigned directly to East Tank Farms, West Tank Farms, and a core Safety Group in TWRS Engineering. The Characterization Project Operations (CPO) safety organization will remain in tact as it currently exists. Personnel assigned to East Tank Farms, West Tank Farms, and CPO will perform facility-specific or project-specific duties and provide field implementation of programs. Those assigned to the core group will focus on activities having a TWRS-wide or programmatic focus. Hanford-wide activities will be the responsibility of the Safety Center of Expertise. In order to ensure an effective and consistent safety program for TWRS under the new organization program functions, goals, organizational structure, roles, responsibilities, and path forward must be clearly established. The purpose of the TWRS Safety Program Plan is to define the overall safety program, responsibilities, relationships, and communication linkages for safety personnel under the new structure. In addition, issues associated with reorganization transition are addressed, including training, project ownership, records management, and dissemination of equipment. For the purpose of this document ``TWRS Safety`` refers to all safety professionals and technicians (Industrial Safety, Industrial Hygiene, Fire Protection, and Nuclear Safety) within the TWRS organization, regardless of their

  7. Demonstration testing and evaluation of in situ soil heating. Health and safety plan (Revision 2)

    SciTech Connect

    Dev, H.

    1994-12-28

    This document is the Health and Safety Plan (HASP) for the demonstration of IITRI`s EM Treatment Technology. In this process, soil is heated in situ by means of electrical energy for the removal of hazardous organic contaminants. This process will be demonstrated on a small plot of contaminated soil located in the Pit Area of Classified Burial Ground K-1070-D, K-25 Site, Oak Ridge, TN. The purpose of the demonstration is to remove organic contaminants present in the soil by heating to a temperature range of 85{degrees} to 95{degrees}C. The soil will be heated in situ by applying 60-Hz AC power to an array of electrodes placed in boreholes drilled through the soil. In this section a brief description of the process is given along with a description of the site and a listing of the contaminants found in the area.

  8. Pupil Transportation Safety Program Plan.

    ERIC Educational Resources Information Center

    Delahanty, Joseph F.; And Others

    This study has been undertaken to assess the magnitude of the school bus safety problem and to develop a plan to improve pupil transportation safety. The resulting report provides estimates of school bus population and daily usage, gives an account of injuries and fatalities that occur annually, and compares the safety records of school buses to…

  9. Developing a patient safety plan.

    PubMed

    Zimmerman, Rosanne; Ip, Ivan; Christoffersen, Emily; Shaver, Jill

    2008-01-01

    Many healthcare organizations are focused on the development of a strategic plan to enhance patient safety. The challenge is creating a plan that focuses on patient safety outcomes, integrating the multitude of internal and external drivers of patient safety, aligning improvement initiatives to create synergy and providing a framework for meaningful measurement of intermediate and long-term results while remaining consistent with an organizational mission, vision and strategic goals. This strategy-focused approach recognizes that patient safety initiatives completed in isolation will not provide consistent progress toward a goal, and that a balanced approach is required that includes the development and systematic execution of bundles of related initiatives. This article outlines the process used by Hamilton Health Sciences in adopting Kaplan and Norton's strategy map methodology underpinned by their balanced scorecard framework to create a comprehensive multi-year plan for patient safety that integrates best practice literature from patient safety, quality and organizational development. PMID:18382157

  10. Health and safety plan for the Environmental Restoration Program at Oak Ridge National Laboratory

    SciTech Connect

    Clark, C. Jr.; Burman, S.N.; Cipriano, D.J. Jr.; Uziel, M.S.; Kleinhans, K.R.; Tiner, P.F.

    1994-08-01

    This Programmatic Health and Safety plan (PHASP) is prepared for the U.S. Department of Energy (DOE) Oak Ridge National Laboratory (ORNL) Environmental Restoration (ER) Program. This plan follows the format recommended by the U.S. Environmental Protection Agency (EPA) for remedial investigations and feasibility studies and that recommended by the EM40 Health and Safety Plan (HASP) Guidelines (DOE February 1994). This plan complies with the Occupational Safety and Health Administration (OSHA) requirements found in 29 CFR 1910.120 and EM-40 guidelines for any activities dealing with hazardous waste operations and emergency response efforts and with OSHA requirements found in 29 CFR 1926.65. The policies and procedures in this plan apply to all Environmental Restoration sites and activities including employees of Energy Systems, subcontractors, and prime contractors performing work for the DOE ORNL ER Program. The provisions of this plan are to be carried out whenever activities are initiated that could be a threat to human health or the environment. This plan implements a policy and establishes criteria for the development of procedures for day-to-day operations to prevent or minimize any adverse impact to the environment and personnel safety and health and to meet standards that define acceptable management of hazardous and radioactive materials and wastes. The plan is written to utilize past experience and best management practices to minimize hazards to human health and safety and to the environment from event such as fires, explosions, falls, mechanical hazards, or any unplanned release of hazardous or radioactive materials to air, soil, or surface water.

  11. Planning for Campus Safety

    ERIC Educational Resources Information Center

    Dessoff, Alan

    2009-01-01

    From natural disasters to criminal violence, facilities officers are often called on to address campus safety and security issues beyond their usual responsibilities. Their experiences in coping with unanticipated events have produced a catalogue of lessons learned that can help them and their peers at other institutions who might face the same…

  12. Magnesium and Silicon Isotopes in HASP Glasses from Apollo 16 Lunar Soil 61241

    NASA Technical Reports Server (NTRS)

    Herzog, G. F.; Delaney, J. S.; Lindsay, F.; Alexander, C. M. O'D; Chakrabarti, R.; Jacobsen, S. B.; Whattam, S.; Korotev, R.; Zeigler, R. A.

    2012-01-01

    The high-Al (>28 wt %), silica-poor (<45 wt %) (HASP) feldspathic glasses of Apollo 16 are widely regarded as the evaporative residues of impacts in the lunar regolith [1-3]. By virtue of their small size, apparent homogeneity, and high inferred formation temperatures, the HASP glasses appear to be good samples in which to study fractionation processes that may accompany open system evaporation. Calculations suggest that HASP glasses with present-day Al2O3 concentrations of up to 40 wt% may have lost 19 wt% of their original masses, calculated as the oxides of iron and silicon, via evaporation [4]. We report Mg and Si isotope abundances in 10 HASP glasses and 2 impact-glass spherules from a 64-105 m grain-size fraction taken from Apollo 16 soil sample 61241.

  13. Signal-to-symbol transformation: a summary of HASP/SIAP case study (sonar data)

    SciTech Connect

    Penny Nii, H.

    1983-01-01

    In the past fifteen years, ai scientists have built several signal interpretation, or understanding, programs. HASP/SIAP is one such program which tries to interest the meaning of sonar data in a particular context. An attempt is made to present a methodology for understanding signal data and to show that the traditional signal processing is but one part of the interpretation task. HASP/SIAP is also an expert system. 12 references.

  14. Chemical Hygiene and Safety Plan

    SciTech Connect

    Berkner, K.

    1992-08-01

    The objective of this Chemical Hygiene and Safety Plan (CHSP) is to provide specific guidance to all LBL employees and contractors who use hazardous chemicals. This Plan, when implemented, fulfills the requirements of both the Federal OSHA Laboratory Standard (29 CFR 1910.1450) for laboratory workers, and the Federal OSHA Hazard Communication Standard (29 CFR 1910.1200) for non-laboratory operations (e.g., shops). It sets forth safety procedures and describes how LBL employees are informed about the potential chemical hazards in their work areas so they can avoid harmful exposures and safeguard their health. Generally, communication of this Plan will occur through training and the Plan will serve as a the framework and reference guide for that training.

  15. Health and safety plan for the Isotopes Facilities Deactivation Project at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect

    1996-08-01

    This HASP describes the process for identifying the requirements, written safety documentation, and procedures for protecting personnel involved in the Isotopes Facilities Deactivation Project. Objective of this project is to place 19 former isotope production facilities at ORNL in a safe condition in anticipation of an extended period of minimum surveillance and maintenance.

  16. EM Health and Safety Plan Guidelines

    SciTech Connect

    Not Available

    1994-12-01

    This document contains information about the Health and Safety Plan Guidelines. Topics discussed include: Regulatory framework; key personnel; hazard assessment; training requirements; personal protective equipment; extreme temperature disorders or conditions; medical surveillance; exposure monitoring/air sampling; site control; decontamination; emergency response/contingency plan; emergency action plan; confined space entry; and spill containment.

  17. Safety Plan for Schools: No Guns

    ERIC Educational Resources Information Center

    Shah, Nirvi

    2013-01-01

    In a pre-emptive move against a school safety proposal from the National Rifle Association that is expected to include a call for more people trained and approved to carry guns at schools, a coalition of civil rights and education groups unveiled its own safety plan last week. It seeks the creation of positive school climates, thoughtful and…

  18. Health and safety plan for the Remedial Investigation and Site Investigation of Waste Area Grouping 2 at the Oak Ridge National Laboratory, Oak Ridge, Tennessee. Environmental Restoration Program

    SciTech Connect

    Cofer, G.H.; Holt, V.L.; Roupe, G.W.

    1993-11-01

    This health and safety plan (HASP) was developed by the members of the Measurement Applications and Development Group of the Health Science Research Division at the Oak Ridge National Laboratory (ORNL). This plan was prepared to ensure that health and safety related items for the Waste Area Grouping (WAG) 2 Remedial Investigation (RI)/Feasibility Study and Site Investigation projects conform with the requirements of 29 CFR 1910.120 (April 18, 1992). The RI Plan calls for the characterization, monitoring, risk assessment, and identification of remedial needs and alternatives that have been structured and staged with short-term and long-term objectives. In early FY 1992, the WAG 2 RI was integrated with the ORNL Environmental Restoration (ER) Site Investigations program in order to achieve the complimentary objectives of the projects more effectively by providing an integrated basis of support. The combined effort was named the WAG 2 Remedial Investigation and Site Investigations Program (WAG 2 RI&SI). The Site Investigation activities are a series of monitoring efforts and directed investigations that support other ER activities by providing information about (1) watershed hydrogeology; (2) contaminants, pathways, and fluxes for groundwater at ORNL; (3) shallow subsurface areas that can act as secondary sources of contaminants; and (4) biological populations and contaminants in biota, in addition to other support and coordination activities.

  19. The high altitude student platform (HASP) for student-built payloads

    NASA Astrophysics Data System (ADS)

    Guzik, T. Gregory; Wefel, John P.

    An outstanding issue with aerospace workforce development is what should be done at the university level to attract and prepare undergraduates for an aerospace career. One approach adopted by many institutions is to lead students through the design and development of small payloads (less than about 500 grams) that can be carried up to high altitude (around 30 km) by a latex sounding balloon. This approach has been very successful in helping students to integrate their content knowledge with practical skills and to understand the end-to-end process of aerospace project development. Sounding balloons, however, are usually constrained in flight duration (˜30 min above 24 km) and payload weight, limiting the kinds investigations that are possible. Student built picosatellites, such as CubeSats, can be placed in low Earth orbit removing the flight duration constraint, but the delays between satellite development and launch can be years. Here, we present the inexpensive high altitude student platform (HASP) that is designed to carry at least eight student payloads at a time to an altitude of about 36 km with flight durations of 15 20 h using a small zero-pressure polyethylene film balloon. This platform provides a flight capability greater than sounding balloons and can be used to flight-test compact satellites, prototypes and other small payloads designed and built by students. The HASP includes a standard mechanical, power and communication interface for the student payload to simplify integration and allows the payloads to be fully exercised. HASP is lightweight, has simple mission requirements providing flexibility in the launch schedule, will provide a flight test opportunity at the end of each academic year.

  20. 49 CFR 238.603 - Safety planning requirements.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Safety planning requirements. 238.603 Section 238... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PASSENGER EQUIPMENT SAFETY STANDARDS Specific Safety Planning Requirements for Tier II Passenger Equipment § 238.603 Safety planning requirements. (a) Prior to...

  1. 48 CFR 1852.223-73 - Safety and Health Plan.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 6 2011-10-01 2011-10-01 false Safety and Health Plan... 1852.223-73 Safety and Health Plan. As prescribed in 1823.7001(c), insert the following provision: Safety and Health Plan (NOV 2004) (a) The offeror shall submit a detailed safety and occupational...

  2. 48 CFR 1852.223-73 - Safety and Health Plan.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 48 Federal Acquisition Regulations System 6 2013-10-01 2013-10-01 false Safety and Health Plan... 1852.223-73 Safety and Health Plan. As prescribed in 1823.7001(c), insert the following provision: Safety and Health Plan (NOV 2004) (a) The offeror shall submit a detailed safety and occupational...

  3. 49 CFR 238.603 - Safety planning requirements.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 4 2011-10-01 2011-10-01 false Safety planning requirements. 238.603 Section 238... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PASSENGER EQUIPMENT SAFETY STANDARDS Specific Safety Planning Requirements for Tier II Passenger Equipment § 238.603 Safety planning requirements. (a) Prior to...

  4. Certification plan for safety and PRA codes

    SciTech Connect

    Toffer, H.; Crowe, R.D.; Ades, M.J.

    1990-05-01

    A certification plan for computer codes used in Safety Analyses and Probabilistic Risk Assessment (PRA) for the operation of the Savannah River Site (SRS) reactors has been prepared. An action matrix, checklists, and a time schedule have been included in the plan. These items identify what is required to achieve certification of the codes. A list of Safety Analysis and Probabilistic Risk Assessment (SA&PRA) computer codes covered by the certification plan has been assembled. A description of each of the codes was provided in Reference 4. The action matrix for the configuration control plan identifies code specific requirements that need to be met to achieve the certification plan`s objectives. The checklist covers the specific procedures that are required to support the configuration control effort and supplement the software life cycle procedures based on QAP 20-1 (Reference 7). A qualification checklist for users establishes the minimum prerequisites and training for achieving levels of proficiency in using configuration controlled codes for critical parameter calculations.

  5. Certification plan for safety and PRA codes

    SciTech Connect

    Toffer, H.; Crowe, R.D. ); Ades, M.J. )

    1990-05-01

    A certification plan for computer codes used in Safety Analyses and Probabilistic Risk Assessment (PRA) for the operation of the Savannah River Site (SRS) reactors has been prepared. An action matrix, checklists, and a time schedule have been included in the plan. These items identify what is required to achieve certification of the codes. A list of Safety Analysis and Probabilistic Risk Assessment (SA PRA) computer codes covered by the certification plan has been assembled. A description of each of the codes was provided in Reference 4. The action matrix for the configuration control plan identifies code specific requirements that need to be met to achieve the certification plan's objectives. The checklist covers the specific procedures that are required to support the configuration control effort and supplement the software life cycle procedures based on QAP 20-1 (Reference 7). A qualification checklist for users establishes the minimum prerequisites and training for achieving levels of proficiency in using configuration controlled codes for critical parameter calculations.

  6. Safety analysis report for packaging upgrade plan

    SciTech Connect

    KELLY, D.L.

    1998-11-18

    This Safety Analysis Report for Packaging (SARP) Upgrade Plan reflects a revised SARP upgrade schedule based on the most current program needs. A Project Hanford Management Contract (PHMC) Performance Expectation exists to update, revise, and/or cancel seven onsite SARPS during FY 1999. It is the U.S. Department of Energy's desire that 100% of the SARPs (which existed at the beginning of the PHMC Contract) be upgraded, revised, and/or canceled by the end of the five year contract. This plan is a ''living'' document and is used as a management tool.

  7. UMTRA Project: Environment, Safety, and Health Plan

    SciTech Connect

    Not Available

    1995-02-01

    The US Department of Energy has prepared this UMTRA Project Environment, Safety, and Health (ES and H) Plan to establish the policy, implementing requirements, and guidance for the UMTRA Project. The requirements and guidance identified in this plan are designed to provide technical direction to UMTRA Project contractors to assist in the development and implementation of their ES and H plans and programs for UMTRA Project work activities. Specific requirements set forth in this UMTRA Project ES and H Plan are intended to provide uniformity to the UMTRA Project`s ES and H programs for processing sites, disposal sites, and vicinity properties. In all cases, this UMTRA Project ES and H Plan is intended to be consistent with applicable standards and regulations and to provide guidance that is generic in nature and will allow for contractors` evaluation of site or contract-specific ES and H conditions. This plan specifies the basic ES and H requirements applicable to UMTRA Project ES and H programs and delineates responsibilities for carrying out this plan. DOE and contractor ES and H personnel are expected to exercise professional judgment and apply a graded approach when interpreting these guidelines, based on the risk of operations.

  8. Icelandic experience with water safety plans.

    PubMed

    Gunnarsdóttir, M J; Gardarsson, S M; Bartram, J

    2012-01-01

    The aim of this study was to investigate accumulated experience with water safety plans in one of the first countries to adopt systematic preventive management for drinking-water safety. Water utilities in Iceland have had a legal obligation since 1995 to implement a systematic preventive approach to secure safety of drinking water and protect public health. The water utilities responded by implementing either an adapted HACCP (Hazard Analysis Critical Control Points) model for larger water utilities or a simpler five step model for smaller water utilities. The research was carried out at 16 water utilities that serve about two-thirds of the population of Iceland. Both qualitative and quantitative methods were used with the aim of analysing if and what benefits water safety plans bring for water utilities and what is needed for successful implementation and operation of such systems. The results of the study show that numerous benefits and even the process of going through the implementing process were considered to be of advantage and change the attitude of the staff and the utility culture. Some obstacles and shortcomings came to light, such as lack of documentation and lack of regular internal and external audit. There was little communication with the public, although some mentioned that good public relations are important to succeed with water safety plans. Many important elements of success were revealed of which intensive training of staff and participation of staff in the whole process are deemed the most important. It is also important to have simple and well-structured guidelines, and good cooperation with the health authorities.

  9. Geochemistry of HASP, VLT, and other glasses from double drive tube 79001/2

    NASA Technical Reports Server (NTRS)

    Lindstrom, D. J.; Wentworth, S. J.; Martinez, R. R.; Mckay, D. S.

    1992-01-01

    The Apollo 17 double drive tube 79001/2 (station 9, Van Serg Crater) is distinctive because of its extreme maturity, abundance, and variety of glass clasts. It contains mare glasses of both high Ti and very low Ti (VLT) compositions, and highland glasses of all compositions common in lunar regolith samples: highland basalt (feldspathic; Al2O3 greater than 23 wt percent), KREEP (Al2O3 less than 23 wt percent, K2O greater than 0.25 wt percent), and low-K Fra Mauro (LKFM; Al2O3 less than 23 wt percent, K2O less than 0.25 wt percent). It also contains rare specimens of high-alumina, silica-poor (HASP), and ultra Mg glasses. HASP glasses contain insufficient SiO2 to permit the calculation of a standard norm, and are thought to be the product of volatilization during impact melting. They have been studied by electron microprobe major-element analysis techniques but have not previously been analyzed for trace elements. The samples analyzed for this study were polished grain mounts of the 90-160 micron fraction of four sieved samples from the 79001/2 core (depth range 2.3-11.5 cm). A total of 80 glasses were analyzed by SEM/EDS and electron microprobe, and a subset of 33 of the glasses, representing a wide range of compositional types, was chosen for high-sensitivity INAA. A microdrilling device removed disks (mostly 50-100 micron diameter, weighing approx. 0.1-0.5 micro-g) for INAA. Preliminary data reported here are based only on short counts done within two weeks of irradiation.

  10. Guideline for the preparation of a contractor safety plan

    SciTech Connect

    Stinnett, L

    1982-04-01

    This document is only a guideline for contractors to use in formalizing a safety program or preparing a safety plan. It contains a format of a suggested safety plan as well as pertinent safety elements which should be considered for inclusion. However, consideration of only those items listed may not be sufficient. Each contractor should include in the safety plan particular reference to those elements peculiar to the inherent hazards of the contractor's specific type of construction services, whether the hazard is shown in the list of safety elements or not. Each safety plan should be reviewed annually by the contractor's management. Reissue of the safety plan is mandatory if safety requirements have changed, or if the contractor's address or management (approval signature) has changed.

  11. 49 CFR 236.907 - Product Safety Plan (PSP).

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 4 2013-10-01 2013-10-01 false Product Safety Plan (PSP). 236.907 Section 236.907...-Based Signal and Train Control Systems § 236.907 Product Safety Plan (PSP). (a) What must a PSP contain... description of the product functionality and information flows; (4) A safety requirements document,...

  12. Highway Safety Program Manual: Volume O: Planning and Administration.

    ERIC Educational Resources Information Center

    National Highway Traffic Safety Administration (DOT), Washington, DC.

    As the introductory volume to the 19-volume Highway Safety Program Manual (which provides guidance to State and local governments on preferred highway safety practices), the document concentrates on aspects of planning and administration of a statewide highway safety program. Topics discussed are: the purpose of planning and administration,…

  13. 49 CFR 238.603 - Safety planning requirements.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 4 2013-10-01 2013-10-01 false Safety planning requirements. 238.603 Section 238.603 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PASSENGER EQUIPMENT SAFETY STANDARDS Specific Safety Planning Requirements for Tier II Passenger Equipment §...

  14. 49 CFR 238.603 - Safety planning requirements.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 4 2012-10-01 2012-10-01 false Safety planning requirements. 238.603 Section 238.603 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PASSENGER EQUIPMENT SAFETY STANDARDS Specific Safety Planning Requirements for Tier II Passenger Equipment §...

  15. 49 CFR 238.603 - Safety planning requirements.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 4 2014-10-01 2014-10-01 false Safety planning requirements. 238.603 Section 238.603 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PASSENGER EQUIPMENT SAFETY STANDARDS Specific Safety Planning Requirements for Tier II Passenger Equipment §...

  16. Urban planning and traffic safety at night

    NASA Astrophysics Data System (ADS)

    Ispas, N.; Trusca, D.

    2016-08-01

    Urban planning including traffic signs serve vital functions, providing road users with regulatory, warning and guidance information about the roadway and surrounding environment. There are a large number of signs and even more guidelines on how these signs should be designed, installed, and maintained in concordance with on road surface traffic signs. More requirements for signs are made for night urban traffic, including appearance (size, shape, colour), placement (height, lateral, and longitudinal), maintenance (visibility, position, damage) and signs light and retroreflective. In the night, traffic signs visibility can interact by on pedestrian visibility and diminish urban traffic safety. The main aim of this paper are the scientific determination of an urban specific zone visibility for evaluate at night real conditions in case of a traffic accident in the Braşov city area. The night visibility study was made using PC-Rect version 4.2. Other goal of the paper was to modify some urban planning solution in order to increase the urban safety in Brașov.

  17. 48 CFR 1852.223-73 - Safety and Health Plan.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ...: Safety and Health Plan (NOV 2004) (a) The offeror shall submit a detailed safety and occupational health... occupational health of Contractor employees and to ensure the safety of all working conditions throughout the... techniques that will be used to ensure the safety and occupational health of the public, astronauts...

  18. 48 CFR 1852.223-73 - Safety and Health Plan.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ...: Safety and Health Plan (NOV 2004) (a) The offeror shall submit a detailed safety and occupational health... occupational health of Contractor employees and to ensure the safety of all working conditions throughout the... techniques that will be used to ensure the safety and occupational health of the public, astronauts...

  19. 48 CFR 1852.223-73 - Safety and Health Plan.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ...: Safety and Health Plan (NOV 2004) (a) The offeror shall submit a detailed safety and occupational health... occupational health of Contractor employees and to ensure the safety of all working conditions throughout the... techniques that will be used to ensure the safety and occupational health of the public, astronauts...

  20. The High Altitude Student Platform Status and Future Plans

    NASA Astrophysics Data System (ADS)

    Guzik, T. Gregory; Ellison, Steven B.; Gould, Randy; Granger, Douglas; Smith, Douglas; Stewart, Michael; Wefel, John P.

    The High Altitude Student Platform (HASP) is designed to carry multiple student payloads to an altitude of about 36 kilometers with flight durations of 15 to 20 hours using a small volume, zero pressure balloon. To date HASP has had two successful flights (2006, 2007) and is anticipating a third flight this September (2008). Including the upcoming flight, HASP has supported 29 student payloads from 15 institutions across the United States involving about 110 undergraduate and graduate students. By participating in a HASP flight, students gain practical, real-world experience in the design, fabrication, system testing, operation, data analysis and management of an aerospace payload. Such experiences are very difficult to achieve in a normal classroom setting and play an important role in training new aerospace scientists and engineers. During the flights, the HASP control systems have functioned exceptionally well and the modular electronics design has enabled us to maintain flexibility, improve reliability and decrease flight-line support expenses. These capabilities, plus new advances in miniaturized balloon vehicle control systems, may enable the overall weight of HASP to be significantly reduced potentially reducing launch costs and/or improving the student payload to system mass ratio. During the presentation we will discuss the HASP program, previous flights, science results / lessons learned from the student payloads and plans for improving the efficiency of future flights.

  1. PLANNING FOR SAFETY ON THE JOBSITE. SAFETY IN INDUSTRY--CONSTRUCTION INDUSTRY SERIES.

    ERIC Educational Resources Information Center

    OTTO, FRANCIS L.; VAN ATTA, F.A.

    WORK INJURIES AND THEIR MONETARY LOSSES IN THE CONSTRUCTION INDUSTRY CAN BE EFFECTIVELY PREVENTED ONLY THROUGH AN AGGRESSIVE AND WELL-PLANNED SAFETY EFFORT. THIS BULLETIN DISCUSSES THE "HOW" OF PLANNING FOR SAFETY ON THE JOBSITE. IT WAS PREPARED IN THE DIVISION OF PROGRAMING AND RESEARCH, OFFICE OF OCCUPATIONAL SAFETY. CONTENTS INCLUDE (1) THE…

  2. 49 CFR 1106.4 - The Safety Integration Plan process.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 8 2010-10-01 2010-10-01 false The Safety Integration Plan process. 1106.4... OF CONTROL § 1106.4 The Safety Integration Plan process. (a) Each applicant in a transaction subject... ongoing environmental review process under 49 CFR part 1105. The procedures governing the process shall...

  3. School Bus Fleet Safety: Planning and Development.

    ERIC Educational Resources Information Center

    Bieber, Robert M.

    1984-01-01

    To ensure worker safety, fleet safety managers need professional staffs, good access to top management, and sufficient authority to discharge their duties. Safety programs should include careful driver hiring; training, including orientation, testing, and practice; comprehensive accident reporting; and cooperative compliance programs with…

  4. Reactor Safety Planning for Prometheus Project, for Naval Reactors Information

    SciTech Connect

    P. Delmolino

    2005-05-06

    The purpose of this letter is to submit to Naval Reactors the initial plan for the Prometheus project Reactor Safety work. The Prometheus project is currently developing plans for cold physics experiments and reactor prototype tests. These tests and facilities may require safety analysis and siting support. In addition to the ground facilities, the flight reactor units will require unique analyses to evaluate the risk to the public from normal operations and credible accident conditions. This letter outlines major safety documents that will be submitted with estimated deliverable dates. Included in this planning is the reactor servicing documentation and shipping analysis that will be submitted to Naval Reactors.

  5. Nuclear Powerplant Safety: Design and Planning.

    ERIC Educational Resources Information Center

    Department of Energy, Washington, DC. Nuclear Energy Office.

    The most important concern in the design, construction and operation of nuclear powerplants is safety. Nuclear power is one of the major contributors to the nation's supply of electricity; therefore, it is important to assure its safe use. Each different type of powerplant has special design features and systems to protect health and safety. One…

  6. Violence against Women: Safety Planning for Abusive Situations

    MedlinePlus

    ... Car title, registration, and insurance information Records of police reports you have filed or other evidence of ... Violence Prevention Fund) - If your safety is at risk, use this fact sheet to create a plan ...

  7. 9. BUILDING 65 ADDITION. LASER SAFETY TEAM. FLOOR PLAN, ELEVATIONS, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    9. BUILDING 65 ADDITION. LASER SAFETY TEAM. FLOOR PLAN, ELEVATIONS, ETC. March 21, 1973 - Frankford Arsenal, Building No. 65, South of Tacony Street between Bridge Street & tracks of former Pennsylvania Railroad, Philadelphia, Philadelphia County, PA

  8. 49 CFR 236.905 - Railroad Safety Program Plan (RSPP).

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... for Processor-Based Signal and Train Control Systems § 236.905 Railroad Safety Program Plan (RSPP). (a...; and (iv) The identification of the safety assessment process. (2) Design for verification and... RSPP must require that references to any non-published standards be included in the PSP. (3) Design...

  9. Make safety programs work efficiently with an effective management plan

    SciTech Connect

    Lyle, D.

    1995-07-01

    Like budgets or any other major projects, safety works better when everyone in the company commits to manage the program effectively. Let someone overspend a budget or miss a projected revenue plan and a company moves quickly to correct the problem. However, there is a tendency to ignore a manager whose department has a poor safety record, as though it`s bad luck.

  10. 29 CFR 1915.502 - Fire safety plan.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... December 14, 2004, for employees who are currently working; (2) Upon initial assignment for new employees... implement a written fire safety plan that covers all the actions that employers and employees must take to ensure employee safety in the event of a fire. (See Appendix A to this subpart for a Model Fire...

  11. 29 CFR 1915.502 - Fire safety plan.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... December 14, 2004, for employees who are currently working; (2) Upon initial assignment for new employees... implement a written fire safety plan that covers all the actions that employers and employees must take to ensure employee safety in the event of a fire. (See Appendix A to this subpart for a Model Fire...

  12. K basins interim remedial action health and safety plan

    SciTech Connect

    DAY, P.T.

    1999-09-14

    The K Basins Interim Remedial Action Health and Safety Plan addresses the requirements of the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA), as they apply to the CERCLA work that will take place at the K East and K West Basins. The provisions of this plan become effective on the date the US Environmental Protection Agency issues the Record of Decision for the K Basins Interim Remedial Action, currently planned in late August 1999.

  13. NIF conventional facilities construction health and safety plan

    SciTech Connect

    Benjamin, D W

    1998-05-14

    The purpose of this Plan is to outline the minimum health and safety requirements to which all participating Lawrence Livermore National Laboratory (LLNL) and non-LLNL employees (excluding National Ignition Facility [NIF] specific contractors and subcontractors covered under the construction subcontract packages (e.g., CSP-9)-see Construction Safety Program for the National Ignition Facility [CSP] Section I.B. ''NIF Construction Contractors and Subcontractors'' for specifics) shall adhere to for preventing job-related injuries and illnesses during Conventional Facilities construction activities at the NIF Project. For the purpose of this Plan, the term ''LLNL and non-LLNL employees'' includes LLNL employees, LLNL Plant Operations staff and their contractors, supplemental labor, contract labor, labor-only contractors, vendors, DOE representatives, personnel matrixed/assigned from other National Laboratories, participating guests, and others such as visitors, students, consultants etc., performing on-site work or services in support of the NIF Project. Based upon an activity level determination explained in Section 1.2.18, in this document, these organizations or individuals may be required by site management to prepare their own NIF site-specific safety plan. LLNL employees will normally not be expected to prepare a site-specific safety plan. This Plan also outlines job-specific exposures and construction site safety activities with which LLNL and non-LLNL employees shall comply.

  14. Space Station crew safety alternatives study. Volume 5: Space Station safety plan

    NASA Technical Reports Server (NTRS)

    Mead, G. H.; Peercy, R. L., Jr.; Raasch, R. F.

    1985-01-01

    The Space Station Safety Plan has been prepared as an adjunct to the subject contract final report, suggesting the tasks and implementation procedures to ensure that threats are addressed and resolution strategy options identified and incorporated into the space station program. The safety program's approach is to realize minimum risk exposure without levying undue design and operational constraints. Safety objectives and risk acceptances are discussed.

  15. Facility Safety Plan B360 Complex CMLS-411r0

    SciTech Connect

    Cooper, G

    2007-01-08

    Lawrence Livermore National Laboratory's (LLNL) Environmental, Safety and Health (ES&H) policy is that all operations must be planned and performed safely for the protection of workers, the public, the environment, and limit possible loss to property, facilities and equipment assigned to this directorate. In addition to observing LLNL policies contained in the ''Environment, Safety, and Health (ES&H) Manual'', LLNL workers will comply with applicable federal, state, and local regulations when conducting any activity that the Chemistry, Materials and Life Sciences (CMLS) Directorate has managerial control or oversight. Management has determined that the safety controls specified within this Facility Safety Plan (FSP) must also be followed to ensure that the operation is successfully performed efficiently and safely within this facility. Any operations conducted in this Complex that involve activities not commonly performed by the public require an Integration Work Sheet (IWS) or IWS/Safety Plan (IWS/SP) that specifically assesses the responsibilities, hazards and controls to conduct the operation safely. Everyone who enters this area (including students, workers, visitors, and consultants) must follow the applicable requirements in this FSP. Each person is expected to protect himself/herself and others from injury or illness. Regular facility occupants are expected to guide and govern visitors and assist new or temporary occupants in understanding and following this plan. When there are any doubts regarding the safety of any phase of work, workers and others will check with the facility manager. Changes to this FSP will be approved by the Facility Associate Director (AD). This will undergo triennial review to establish, at a minimum, that its contents are appropriate and adequate for current operations. The Hazards Control ES&H Team assists management in instituting and maintaining a minimum-risk and environmentally sound work environment. Any Laboratory worker has

  16. 77 FR 42462 - Hawaii State Plan for Occupational Safety and Health; Proposed Modification of 18(e) Plan Approval

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-07-19

    ... Safety and Health; Proposed Modification of 18(e) Plan Approval AGENCY: Occupational Safety and Health... federal OSHA plan approval on December 28, 1973 (39 FR 1010). The Hawaii Occupational Safety and Health... by the plan, 29 U.S.C. 667(e). Hawaii was granted final approval effective April 30, 1984 (49...

  17. Management implementation plan for a safety analysis and review system

    SciTech Connect

    Hulburt, D.A.; Berkey, B.D.

    1981-04-01

    The US Department of Energy has issued an Order, DOE 5481.1, which establishes uniform requirements for the preparation and review of Safety Analysis for DOE Operations. The Management Implementation Plan specified herein establishes the administrative procedures and technical requirements for implementing DOE 5481.1 to Operations under the cognizance of the Pittsburgh Energy Technology Center. This Implementation Plan is applicable to all present and future Operations under the cognizance of PETC. The Plan identifies those Operations for which DOE 5481.1 is applicable and those Operations for which no further analysis is required because the initial determination and review has concluded that DOE 5481.1 does not apply.

  18. Ready for "Code Red"? Pre-Plan for Safety

    ERIC Educational Resources Information Center

    Baker, Davis E.

    2006-01-01

    In this article, the author, a principal of Buckeye Valley High School, Delaware, Ohio, focuses on how to generate a building readiness plan. He suggests that school administrators should have a readily available notebook of emergency response procedures to ensure students' safety. Among other things, he recommends creation of a building…

  19. 49 CFR 236.907 - Product Safety Plan (PSP).

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 4 2014-10-01 2014-10-01 false Product Safety Plan (PSP). 236.907 Section 236.907 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RULES, STANDARDS, AND INSTRUCTIONS GOVERNING THE INSTALLATION, INSPECTION, MAINTENANCE, AND REPAIR OF SIGNAL...

  20. 49 CFR 236.905 - Railroad Safety Program Plan (RSPP).

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ..., INSPECTION, MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Standards for Processor-Based Signal and Train Control Systems § 236.905 Railroad Safety Program Plan (RSPP). (a..., including: (i) A complete description of methods used to evaluate a system's behavioral characteristics;...

  1. 49 CFR 236.905 - Railroad Safety Program Plan (RSPP).

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ..., INSPECTION, MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Standards for Processor-Based Signal and Train Control Systems § 236.905 Railroad Safety Program Plan (RSPP). (a..., including: (i) A complete description of methods used to evaluate a system's behavioral characteristics;...

  2. 49 CFR 236.905 - Railroad Safety Program Plan (RSPP).

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ..., INSPECTION, MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Standards for Processor-Based Signal and Train Control Systems § 236.905 Railroad Safety Program Plan (RSPP). (a..., including: (i) A complete description of methods used to evaluate a system's behavioral characteristics;...

  3. 49 CFR 236.905 - Railroad Safety Program Plan (RSPP).

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ..., INSPECTION, MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Standards for Processor-Based Signal and Train Control Systems § 236.905 Railroad Safety Program Plan (RSPP). (a..., including: (i) A complete description of methods used to evaluate a system's behavioral characteristics;...

  4. 75 FR 70670 - Final Vehicle Safety Rulemaking and Research Priority Plan 2010-2013

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-11-18

    ... National Highway Traffic Safety Administration 49 CFR Part 571 Final Vehicle Safety Rulemaking and Research... availability of the Final Vehicle Safety Rulemaking and Research Priority Plan 2010-2013 (Priority Plan) in Docket No. NHTSA-2009-0108. This Priority Plan is an update to the Final Vehicle Safety Rulemaking...

  5. 49 CFR 659.25 - Annual review of system safety program plan and system security plan.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... (Continued) FEDERAL TRANSIT ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAIL FIXED GUIDEWAY SYSTEMS; STATE... and system security plan. (a) The oversight agency shall require the rail transit agency to conduct an... transit agency's system safety program plan is modified, the rail transit agency must submit the...

  6. 49 CFR 659.25 - Annual review of system safety program plan and system security plan.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... (Continued) FEDERAL TRANSIT ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAIL FIXED GUIDEWAY SYSTEMS; STATE... and system security plan. (a) The oversight agency shall require the rail transit agency to conduct an... transit agency's system safety program plan is modified, the rail transit agency must submit the...

  7. 49 CFR 659.25 - Annual review of system safety program plan and system security plan.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... (Continued) FEDERAL TRANSIT ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAIL FIXED GUIDEWAY SYSTEMS; STATE... and system security plan. (a) The oversight agency shall require the rail transit agency to conduct an... transit agency's system safety program plan is modified, the rail transit agency must submit the...

  8. 49 CFR 659.25 - Annual review of system safety program plan and system security plan.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... (Continued) FEDERAL TRANSIT ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAIL FIXED GUIDEWAY SYSTEMS; STATE... and system security plan. (a) The oversight agency shall require the rail transit agency to conduct an... transit agency's system safety program plan is modified, the rail transit agency must submit the...

  9. 49 CFR 659.25 - Annual review of system safety program plan and system security plan.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... (Continued) FEDERAL TRANSIT ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAIL FIXED GUIDEWAY SYSTEMS; STATE... and system security plan. (a) The oversight agency shall require the rail transit agency to conduct an... transit agency's system safety program plan is modified, the rail transit agency must submit the...

  10. Site Safety Plan for Lawrence Livermore National Laboratory CERCLA investigations

    SciTech Connect

    Bainer, R.; Duarte, J.

    1993-07-01

    The safety policy of LLNL is to take every reasonable precaution in the performance of work to protect the environment and the health and safety of employees and the public, and to prevent property damage. With respect to hazardous agents, this protection is provided by limiting human exposures, releases to the environment, and contamination of property to levels that are as low as reasonably achievable (ALARA). It is the intent of this Plan to supply the broad outline for completing environmental investigations within ALARA guidelines. It may not be possible to determine actual working conditions in advance of the work; therefore, planning must allow the opportunity to provide a range of protection based upon actual working conditions. Requirements will be the least restrictive possible for a given set of circumstances, such that work can be completed in an efficient and timely fashion. Due to the relatively large size of the LLNL Site and the different types of activities underway, site-specific Operational Safety Procedures (OSPs) will be prepared to supplement activities not covered by this Plan. These site-specific OSPs provide the detailed information for each specific activity and act as an addendum to this Plan, which provides the general plan for LLNL Main Site operation.

  11. 78 FR 61251 - The National Public Transportation Safety Plan, the Public Transportation Agency Safety Plan, and...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-10-03

    ... April 11, 2000, at 65 FR 19477-8 or http://DocketsInfo.dot.gov . FOR FURTHER INFORMATION CONTACT: Safety... light of high profile rail transit accidents discussed in section IIIA, below. Modern safety management... red flag. Accordingly, any residual risk would be accepted and the agency would focus on those...

  12. Health and safety plan for operations performed for the Environmental Restoration Program

    SciTech Connect

    Trippet, W.A. II ); Reneau, M.; Morton, S.L. )

    1992-04-01

    This document constitutes the generic health and safety plan for the Environmental Restoration Program (ERP). It addresses the health and safety requirements of the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA); Occupational Safety and Health Administration (OSHA) 29 CFR 1910.120 standard; and EG G Idaho, Inc. This plan is a guide to individuals who must complete a health and safety plan for a task performed for the EPR. It contains a task specific addendum that, when completed, specifically addresses task specific health and safety issues. This health and safety plan reduces the time it takes to write a task specific health and safety plan by providing discussions of requirements, guidance on where specific information is located, and specific topics in the Addendum that must be discussed at a task level. This format encourages a complete task specific health and safety plan and a standard for all health and safety plans written for ERP.

  13. Product Safety, It's No Accident. A Consumer Product Safety Monthly Planning Guide for Community Organizations.

    ERIC Educational Resources Information Center

    Consumer Product Safety Commission, Washington, DC.

    A consumer product safety monthly planning guide for community organizations is provided. The material is organized into suggested monthly topics with seasonal emphasis. Each section highlights selected information about how to identify potential hazards associated with categories of products. Each section also includes recommendaitons of ways to…

  14. Planning for Safety on the Jobsite. Safety in Industry, Construction Industry Series.

    ERIC Educational Resources Information Center

    Occupational Safety and Health Administration, Washington, DC.

    Work injuries and their monetary losses in the construction industry can be effectively prevented only through an aggressive and well-planned safety effort. The purpose of this bulletin is to provide guidelines to aid the construction contractor in complying with legal requirements and in attaining the objective of keeping costly accidents and…

  15. Therapeutic risk management of the suicidal patient: safety planning.

    PubMed

    Matarazzo, Bridget B; Homaifar, Beeta Y; Wortzel, Hal S

    2014-05-01

    This column is the fourth in a series describing a model for therapeutic risk management of the suicidal patient. Previous columns presented an overview of the therapeutic risk management model, provided recommendations for how to augment risk assessment using structured assessments, and discussed the importance of risk stratification in terms of both severity and temporality. This final column in the series discusses the safety planning intervention as a critical component of therapeutic risk management of suicide risk. We first present concerns related to the relatively common practice of using no-suicide contracts to manage risk. We then present the safety planning intervention as an alternative approach and provide recommendations for how to use this innovative strategy to therapeutically mitigate risk in the suicidal patient.

  16. TWRS safety and technical integration risk management plan

    SciTech Connect

    Fordham, R.A.

    1996-03-12

    The objectives of the Tank Waste Remediation System (TWRS) Safety and Technical Integration (STI) programmatic risk management program are to assess, analyze, and handle risks associated with TWRS STI responsibilities and to communicate information about the actions being taken and the results to enable decision making. The objective of this TWRS STI Risk Management Plan is to communicate a consistent approach to risk management that will be used by the organization.

  17. 49 CFR 1106.3 - Actions for which Safety Integration Plan is required.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 8 2010-10-01 2010-10-01 false Actions for which Safety Integration Plan is... TRANSPORTATION BOARD CONSIDERATION OF SAFETY INTEGRATION PLANS IN CASES INVOLVING RAILROAD CONSOLIDATIONS, MERGERS, AND ACQUISITIONS OF CONTROL § 1106.3 Actions for which Safety Integration Plan is required. A...

  18. 49 CFR 244.11 - Contents of a Safety Integration Plan.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Contents of a Safety Integration Plan. 244.11... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION REGULATIONS ON SAFETY INTEGRATION PLANS GOVERNING RAILROAD CONSOLIDATIONS, MERGERS, AND ACQUISITIONS OF CONTROL Safety Integration Plans § 244.11 Contents of a...

  19. 49 CFR 244.11 - Contents of a Safety Integration Plan.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 4 2011-10-01 2011-10-01 false Contents of a Safety Integration Plan. 244.11... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION REGULATIONS ON SAFETY INTEGRATION PLANS GOVERNING RAILROAD CONSOLIDATIONS, MERGERS, AND ACQUISITIONS OF CONTROL Safety Integration Plans § 244.11 Contents of a...

  20. 49 CFR 244.11 - Contents of a Safety Integration Plan.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 4 2013-10-01 2013-10-01 false Contents of a Safety Integration Plan. 244.11... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION REGULATIONS ON SAFETY INTEGRATION PLANS GOVERNING RAILROAD CONSOLIDATIONS, MERGERS, AND ACQUISITIONS OF CONTROL Safety Integration Plans § 244.11 Contents of a...

  1. 49 CFR 1106.3 - Actions for which Safety Integration Plan is required.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 8 2013-10-01 2013-10-01 false Actions for which Safety Integration Plan is... TRANSPORTATION BOARD CONSIDERATION OF SAFETY INTEGRATION PLANS IN CASES INVOLVING RAILROAD CONSOLIDATIONS, MERGERS, AND ACQUISITIONS OF CONTROL § 1106.3 Actions for which Safety Integration Plan is required. A...

  2. 49 CFR 1106.3 - Actions for which Safety Integration Plan is required.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 8 2012-10-01 2012-10-01 false Actions for which Safety Integration Plan is... TRANSPORTATION BOARD CONSIDERATION OF SAFETY INTEGRATION PLANS IN CASES INVOLVING RAILROAD CONSOLIDATIONS, MERGERS, AND ACQUISITIONS OF CONTROL § 1106.3 Actions for which Safety Integration Plan is required. A...

  3. 49 CFR 1106.3 - Actions for which Safety Integration Plan is required.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 8 2011-10-01 2011-10-01 false Actions for which Safety Integration Plan is... TRANSPORTATION BOARD CONSIDERATION OF SAFETY INTEGRATION PLANS IN CASES INVOLVING RAILROAD CONSOLIDATIONS, MERGERS, AND ACQUISITIONS OF CONTROL § 1106.3 Actions for which Safety Integration Plan is required. A...

  4. 49 CFR 244.11 - Contents of a Safety Integration Plan.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 4 2014-10-01 2014-10-01 false Contents of a Safety Integration Plan. 244.11... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION REGULATIONS ON SAFETY INTEGRATION PLANS GOVERNING RAILROAD CONSOLIDATIONS, MERGERS, AND ACQUISITIONS OF CONTROL Safety Integration Plans § 244.11 Contents of a...

  5. 49 CFR 244.11 - Contents of a Safety Integration Plan.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 4 2012-10-01 2012-10-01 false Contents of a Safety Integration Plan. 244.11... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION REGULATIONS ON SAFETY INTEGRATION PLANS GOVERNING RAILROAD CONSOLIDATIONS, MERGERS, AND ACQUISITIONS OF CONTROL Safety Integration Plans § 244.11 Contents of a...

  6. 49 CFR 1106.3 - Actions for which Safety Integration Plan is required.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 8 2014-10-01 2014-10-01 false Actions for which Safety Integration Plan is... TRANSPORTATION BOARD CONSIDERATION OF SAFETY INTEGRATION PLANS IN CASES INVOLVING RAILROAD CONSOLIDATIONS, MERGERS, AND ACQUISITIONS OF CONTROL § 1106.3 Actions for which Safety Integration Plan is required. A...

  7. National plan to enhance aviation safety through human factors improvements

    NASA Technical Reports Server (NTRS)

    Foushee, Clay

    1990-01-01

    The purpose of this section of the plan is to establish a development and implementation strategy plan for improving safety and efficiency in the Air Traffic Control (ATC) system. These improvements will be achieved through the proper applications of human factors considerations to the present and future systems. The program will have four basic goals: (1) prepare for the future system through proper hiring and training; (2) develop a controller work station team concept (managing human errors); (3) understand and address the human factors implications of negative system results; and (4) define the proper division of responsibilities and interactions between the human and the machine in ATC systems. This plan addresses six program elements which together address the overall purpose. The six program elements are: (1) determine principles of human-centered automation that will enhance aviation safety and the efficiency of the air traffic controller; (2) provide new and/or enhanced methods and techniques to measure, assess, and improve human performance in the ATC environment; (3) determine system needs and methods for information transfer between and within controller teams and between controller teams and the cockpit; (4) determine how new controller work station technology can optimally be applied and integrated to enhance safety and efficiency; (5) assess training needs and develop improved techniques and strategies for selection, training, and evaluation of controllers; and (6) develop standards, methods, and procedures for the certification and validation of human engineering in the design, testing, and implementation of any hardware or software system element which affects information flow to or from the human.

  8. 76 FR 17808 - Final Vehicle Safety Rulemaking and Research Priority Plan 2011-2013

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-03-31

    ... INFORMATION: On November 9, 2009, NHTSA published a Final Notice in the Federal Register (74 FR 57623... NHTSA Vehicle Safety and Fuel Economy Rulemaking and Research Priority Plan 2011-2013 (Priority Plan) in... Final NHTSA Vehicle Safety and Fuel Economy Rulemaking and Research Priority Plan 2011-2013. This...

  9. 12 CFR 30.4 - Filing of safety and soundness compliance plan.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... is obligated to file, or is currently operating under, a capital restoration plan submitted pursuant... 12 Banks and Banking 1 2011-01-01 2011-01-01 false Filing of safety and soundness compliance plan... AND SOUNDNESS STANDARDS § 30.4 Filing of safety and soundness compliance plan. (a) Schedule for...

  10. 12 CFR 263.303 - Filing of safety and soundness compliance plan.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... obligated to file, or is currently operating under, a capital restoration plan submitted pursuant to section... 12 Banks and Banking 3 2011-01-01 2011-01-01 false Filing of safety and soundness compliance plan... safety and soundness compliance plan. (a) Schedule for filing compliance plan—(1) In general. A...

  11. 12 CFR 263.303 - Filing of safety and soundness compliance plan.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... State member bank is obligated to file, or is currently operating under, a capital restoration plan... 12 Banks and Banking 4 2012-01-01 2012-01-01 false Filing of safety and soundness compliance plan... Filing of safety and soundness compliance plan. (a) Schedule for filing compliance plan—(1) In general....

  12. 12 CFR 391.12 - Filing of safety and soundness compliance plan.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... file, or is currently operating under, a capital restoration plan submitted pursuant to section 38 of... 12 Banks and Banking 5 2013-01-01 2013-01-01 false Filing of safety and soundness compliance plan... and Compliance Procedures § 391.12 Filing of safety and soundness compliance plan. (a) Schedule...

  13. 12 CFR 30.4 - Filing of safety and soundness compliance plan.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... is obligated to file, or is currently operating under, a capital restoration plan submitted pursuant... 12 Banks and Banking 1 2013-01-01 2013-01-01 false Filing of safety and soundness compliance plan... AND SOUNDNESS STANDARDS § 30.4 Filing of safety and soundness compliance plan. (a) Schedule for...

  14. 12 CFR 391.12 - Filing of safety and soundness compliance plan.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... file, or is currently operating under, a capital restoration plan submitted pursuant to section 38 of... 12 Banks and Banking 5 2012-01-01 2012-01-01 false Filing of safety and soundness compliance plan... and Compliance Procedures § 391.12 Filing of safety and soundness compliance plan. (a) Schedule...

  15. [Post-marketing drug safety-risk management plan(RMP)].

    PubMed

    Ezaki, Asami; Hori, Akiko

    2013-03-01

    The Guidance for Risk Management Plan(RMP)was released by the Ministry of Health, Labour and Welfare in April 2012. The RMP consists of safety specifications, pharmacovigilance plans and risk minimization action plans. In this paper, we outline post-marketing drug safety operations in PMDA and the RMP, with examples of some anticancer drugs.

  16. National ignition facility environment, safety, and health management plan

    SciTech Connect

    1995-11-01

    The ES&H Management Plan describes all of the environmental, safety, and health evaluations and reviews that must be carried out in support of the implementation of the National Ignition Facility (NIF) Project. It describes the policy, organizational responsibilities and interfaces, activities, and ES&H documents that will be prepared by the Laboratory Project Office for the DOE. The only activity not described is the preparation of the NIF Project Specific Assessment (PSA), which is to be incorporated into the Programmatic Environmental Impact Statement for Stockpile Stewardship and Management (PEIS). This PSA is being prepared by Argonne National Laboratory (ANL) with input from the Laboratory participants. As the independent NEPA document preparers ANL is directly contracted by the DOE, and its deliverables and schedule are agreed to separately with DOE/OAK.

  17. Benefits of Water Safety Plans: microbiology, compliance, and public health.

    PubMed

    Gunnarsdottir, Maria J; Gardarsson, Sigurdur M; Elliott, Mark; Sigmundsdottir, Gudrun; Bartram, Jamie

    2012-07-17

    The Water Safety Plan (WSP) methodology, which aims to enhance safety of drinking water supplies, has been recommended by the World Health Organization since 2004. WSPs are now used worldwide and are legally required in several countries. However, there is limited systematic evidence available demonstrating the effectiveness of WSPs on water quality and health. Iceland was one of the first countries to legislate the use of WSPs, enabling the analysis of more than a decade of data on impact of WSP. The objective was to determine the impact of WSP implementation on regulatory compliance, microbiological water quality, and incidence of clinical cases of diarrhea. Surveillance data on water quality and diarrhea were collected and analyzed. The results show that HPC (heterotrophic plate counts), representing microbiological growth in the water supply system, decreased statistically significant with fewer incidents of HPC exceeding 10 cfu per mL in samples following WSP implementation and noncompliance was also significantly reduced (p < 0.001 in both cases). A significant decrease in incidence of diarrhea was detected where a WSP was implemented, and, furthermore, the results indicate that population where WSP has been implemented is 14% less likely to develop clinical cases of diarrhea.

  18. Sodium fast reactor safety and licensing research plan. Volume II.

    SciTech Connect

    Ludewig, H.; Powers, D. A.; Hewson, John C.; LaChance, Jeffrey L.; Wright, A.; Phillips, J.; Zeyen, R.; Clement, B.; Garner, Frank; Walters, Leon; Wright, Steve; Ott, Larry J.; Suo-Anttila, Ahti Jorma; Denning, Richard; Ohshima, Hiroyuki; Ohno, S.; Miyhara, S.; Yacout, Abdellatif; Farmer, M.; Wade, D.; Grandy, C.; Schmidt, R.; Cahalen, J.; Olivier, Tara Jean; Budnitz, R.; Tobita, Yoshiharu; Serre, Frederic; Natesan, Ken; Carbajo, Juan J.; Jeong, Hae-Yong; Wigeland, Roald; Corradini, Michael; Thomas, Justin; Wei, Tom; Sofu, Tanju; Flanagan, George F.; Bari, R.; Porter D.; Lambert, J.; Hayes, S.; Sackett, J.; Denman, Matthew R.

    2012-05-01

    Expert panels comprised of subject matter experts identified at the U.S. National Laboratories (SNL, ANL, INL, ORNL, LBL, and BNL), universities (University of Wisconsin and Ohio State University), international agencies (IRSN, CEA, JAEA, KAERI, and JRC-IE) and private consultation companies (Radiation Effects Consulting) were assembled to perform a gap analysis for sodium fast reactor licensing. Expert-opinion elicitation was performed to qualitatively assess the current state of sodium fast reactor technologies. Five independent gap analyses were performed resulting in the following topical reports: (1) Accident Initiators and Sequences (i.e., Initiators/Sequences Technology Gap Analysis), (2) Sodium Technology Phenomena (i.e., Advanced Burner Reactor Sodium Technology Gap Analysis), (3) Fuels and Materials (i.e., Sodium Fast Reactor Fuels and Materials: Research Needs), (4) Source Term Characterization (i.e., Advanced Sodium Fast Reactor Accident Source Terms: Research Needs), and (5) Computer Codes and Models (i.e., Sodium Fast Reactor Gaps Analysis of Computer Codes and Models for Accident Analysis and Reactor Safety). Volume II of the Sodium Research Plan consolidates the five gap analysis reports produced by each expert panel, wherein the importance of the identified phenomena and necessities of further experimental research and code development were addressed. The findings from these five reports comprised the basis for the analysis in Sodium Fast Reactor Research Plan Volume I.

  19. 3S (Safeguards, Security, Safety) based pyroprocessing facility safety evaluation plan

    SciTech Connect

    Ku, J.H.; Choung, W.M.; You, G.S.; Moon, S.I.; Park, S.H.; Kim, H.D.

    2013-07-01

    The big advantage of pyroprocessing for the management of spent fuels against the conventional reprocessing technologies lies in its proliferation resistance since the pure plutonium cannot be separated from the spent fuel. The extracted materials can be directly used as metal fuel in a fast reactor, and pyroprocessing reduces drastically the volume and heat load of the spent fuel. KAERI has implemented the SBD (Safeguards-By-Design) concept in nuclear fuel cycle facilities. The goal of SBD is to integrate international safeguards into the entire facility design process since the very beginning of the design phase. This paper presents a safety evaluation plan using a conceptual design of a reference pyroprocessing facility, in which 3S (Safeguards, Security, Safety)-By-Design (3SBD) concept is integrated from early conceptual design phase. The purpose of this paper is to establish an advanced pyroprocessing hot cell facility design concept based on 3SBD for the successful realization of pyroprocessing technology with enhanced safety and proliferation resistance.

  20. 49 CFR 659.19 - System safety program plan: contents.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... formal safety certification but which may have safety impacts. (h) A description of the safety certification process required by the rail transit agency to ensure that safety concerns and hazards are... identified problems into the hazard management process. (p) A description of the training and...

  1. 49 CFR 236.907 - Product Safety Plan (PSP).

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... safety; (5) A document describing the manner in which product architecture satisfies safety requirements... not compromised as a result of any such change. (Software changes involving safety functional... arrangements with hardware and software suppliers for immediate notification of any and all safety...

  2. Making Schools Safe for Students: Creating a Proactive School Safety Plan.

    ERIC Educational Resources Information Center

    Blauvelt, Peter D.

    This guide offers strategies for creating a proactive school safety plan that encourages parents, teachers, principals, and students to take the initiative and identify threats to school safety. It emphasizes that schools must have an active plan that addresses fights, name calling, bullying, changes in kid's behaviors, and staff who have run out…

  3. 77 FR 50727 - Configuration Management Plans for Digital Computer Software Used in Safety Systems of Nuclear...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-08-22

    ... COMMISSION Configuration Management Plans for Digital Computer Software Used in Safety Systems of Nuclear... draft regulatory guide (DG), DG-1206, ``Configuration Management Plan for Digital Computer Software Used... Digital Computer Software Used in Safety Systems of Nuclear Power Plants'' is temporarily identified...

  4. 78 FR 47014 - Configuration Management Plans for Digital Computer Software Used in Safety Systems of Nuclear...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-08-02

    ... 22, 2012 (77 FR 50727) for a 60-day public comment period. The public comment period closed on... COMMISSION Configuration Management Plans for Digital Computer Software Used in Safety Systems of Nuclear... 1 of RG 1.169, ``Configuration Management Plans for Digital Computer Software Used in Safety...

  5. 77 FR 58488 - Hawaii State Plan for Occupational Safety and Health

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-09-21

    ... federal OSHA plan approval on December 28, 1973 (39 FR 1010) and the Hawaii Occupational Safety and Health... Hawaii ``final approval'' effective April 30, 1984 (49 FR 19182). Final approval under Section 18(e... respect to occupational safety and health issues covered by the plan. 29 U.S.C. 667(e). During the...

  6. Planning Document for an NBSR Conversion Safety Analysis Report

    SciTech Connect

    Diamond D. J.; Baek J.; Hanson, A.L.; Cheng, L-Y.; Brown, N.; Cuadra, A.

    2013-09-25

    The NIST Center for Neutron Research (NCNR) is a reactor-laboratory complex providing the National Institute of Standards and Technology (NIST) and the nation with a world-class facility for the performance of neutron-based research. The heart of this facility is the National Bureau of Standards Reactor (NBSR). The NBSR is a heavy water moderated and cooled reactor operating at 20 MW. It is fueled with high-enriched uranium (HEU) fuel elements. A Global Threat Reduction Initiative (GTRI) program is underway to convert the reactor to low-enriched uranium (LEU) fuel. This program includes the qualification of the proposed fuel, uranium and molybdenum alloy foil clad in an aluminum alloy, and the development of the fabrication techniques. This report is a planning document for the conversion Safety Analysis Report (SAR) that would be submitted to, and approved by, the Nuclear Regulatory Commission (NRC) before the reactor could be converted.This report follows the recommended format and content from the NRC codified in NUREG-1537, “Guidelines for Preparing and Reviewing Applications for the Licensing of Non-power Reactors,” Chapter 18, “Highly Enriched to Low-Enriched Uranium Conversions.” The emphasis herein is on the SAR chapters that require significant changes as a result of conversion, primarily Chapter 4, Reactor Description, and Chapter 13, Safety Analysis. The document provides information on the proposed design for the LEU fuel elements and identifies what information is still missing. This document is intended to assist ongoing fuel development efforts, and to provide a platform for the development of the final conversion SAR. This report contributes directly to the reactor conversion pillar of the GTRI program, but also acts as a boundary condition for the fuel development and fuel fabrication pillars.

  7. 49 CFR 659.17 - System safety program plan: general requirements.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... TRANSIT ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAIL FIXED GUIDEWAY SYSTEMS; STATE SAFETY OVERSIGHT... oversight agency shall require the rail transit agency to develop and implement a written system safety...) The oversight agency shall review and approve the rail transit agency system safety program plan....

  8. 49 CFR 659.17 - System safety program plan: general requirements.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... TRANSIT ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAIL FIXED GUIDEWAY SYSTEMS; STATE SAFETY OVERSIGHT... oversight agency shall require the rail transit agency to develop and implement a written system safety...) The oversight agency shall review and approve the rail transit agency system safety program plan....

  9. 49 CFR 659.17 - System safety program plan: general requirements.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... TRANSIT ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAIL FIXED GUIDEWAY SYSTEMS; STATE SAFETY OVERSIGHT... oversight agency shall require the rail transit agency to develop and implement a written system safety...) The oversight agency shall review and approve the rail transit agency system safety program plan....

  10. 49 CFR 659.17 - System safety program plan: general requirements.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... TRANSIT ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAIL FIXED GUIDEWAY SYSTEMS; STATE SAFETY OVERSIGHT... oversight agency shall require the rail transit agency to develop and implement a written system safety...) The oversight agency shall review and approve the rail transit agency system safety program plan....

  11. 49 CFR 659.17 - System safety program plan: general requirements.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... TRANSIT ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAIL FIXED GUIDEWAY SYSTEMS; STATE SAFETY OVERSIGHT... oversight agency shall require the rail transit agency to develop and implement a written system safety...) The oversight agency shall review and approve the rail transit agency system safety program plan....

  12. Community Organizations' Involvement in School Safety Planning: Does It Make a Difference in School Violence?

    ERIC Educational Resources Information Center

    Patton, Joy D.

    2011-01-01

    This study examines the relationship between school violence and involvement of community organizations in school safety planning. The study is a secondary analysis of data from the School Survey on Crime and Safety 2003-2004 (U.S. Department of Education, Institute of Education Sciences, 2006). This survey collects data on crime and safety from…

  13. Safety plan for the cooperative telerobotic retrieval system equipment development area

    SciTech Connect

    Haney, T.J.; Jessmore, J.J.

    1995-07-01

    This plan establishes guidelines to minimize safety risks for the cooperative telerobotic retrieval project at the North Boulevard Annex (NBA). This plan has the dual purpose of minimizing safety risks to workers and visitors and of securing sensitive equipment from inadvertent damage by nonqualified personnel. This goal will be accomplished through physical control of work zones and through assigned responsibilities for project personnel. The scope of this plan is limited to establishing the working zone boundaries and entry requirements, and assigning responsibilities for project personnel. This plan does not supersede current safety organization responsibilities for the Landfill Stabilization Focus Area Transuranic (LSFA TRU) Arid outlined in the Environment, Safety, Health, and Quality Plan for the Buried Waste Integrated Demonstration Program; Tenant Manual; Idaho Falls Building Emergency Control Plan;; applicable Company Procedures; the attached Interface Agreement (Appendix A).

  14. Development of indicators for measuring outcomes of water safety plans

    PubMed Central

    Lockhart, Gabriella; Oswald, William E.; Hubbard, Brian; Medlin, Elizabeth; Gelting, Richard J.

    2015-01-01

    Water safety plans (WSPs) are endorsed by the World Health Organization as the most effective method of protecting a water supply. With the increase in WSPs worldwide, several valuable resources have been developed to assist practitioners in the implementation of WSPs, yet there is still a need for a practical and standardized method of evaluating WSP effectiveness. In 2012, the Centers for Disease Control and Prevention (CDC) published a conceptual framework for the evaluation of WSPs, presenting four key outcomes of the WSP process: institutional, operational, financial and policy change. In this paper, we seek to operationalize this conceptual framework by providing a set of simple and practical indicators for assessing WSP outcomes. Using CDC’s WSP framework as a foundation and incorporating various existing performance monitoring indicators for water utilities, we developed a set of approximately 25 indicators of institutional, operational, financial and policy change within the WSP context. These outcome indicators hold great potential for the continued implementation and expansion of WSPs worldwide. Having a defined framework for evaluating a WSP’s effectiveness, along with a set of measurable indicators by which to carry out that evaluation, will help implementers assess key WSP outcomes internally, as well as benchmark their progress against other WSPs in their region and globally. PMID:26361540

  15. A strategic approach for Water Safety Plans implementation in Portugal.

    PubMed

    Vieira, Jose M P

    2011-03-01

    Effective risk assessment and risk management approaches in public drinking water systems can benefit from a systematic process for hazards identification and effective management control based on the Water Safety Plan (WSP) concept. Good results from WSP development and implementation in a small number of Portuguese water utilities have shown that a more ambitious nationwide strategic approach to disseminate this methodology is needed. However, the establishment of strategic frameworks for systematic and organic scaling-up of WSP implementation at a national level requires major constraints to be overcome: lack of legislation and policies and the need for appropriate monitoring tools. This study presents a framework to inform future policy making by understanding the key constraints and needs related to institutional, organizational and research issues for WSP development and implementation in Portugal. This methodological contribution for WSP implementation can be replicated at a global scale. National health authorities and the Regulator may promote changes in legislation and policies. Independent global monitoring and benchmarking are adequate tools for measuring the progress over time and for comparing the performance of water utilities. Water utilities self-assessment must include performance improvement, operational monitoring and verification. Research and education and resources dissemination ensure knowledge acquisition and transfer.

  16. Oak Ridge National Laboratory Health and Safety Long-Range Plan: Fiscal years 1989--1995

    SciTech Connect

    Not Available

    1989-06-01

    The health and safety of its personnel is the first concern of ORNL and its management. The ORNL Health and Safety Program has the responsibility for ensuring the health and safety of all individuals assigned to ORNL activities. This document outlines the principal aspects of the ORNL Health and Safety Long-Range Plan and provides a framework for management use in the future development of the health and safety program. Each section of this document is dedicated to one of the health and safety functions (i.e., health physics, industrial hygiene, occupational medicine, industrial safety, nuclear criticality safety, nuclear facility safety, transportation safety, fire protection, and emergency preparedness). Each section includes functional mission and objectives, program requirements and status, a summary of program needs, and program data and funding summary. Highlights of FY 1988 are included.

  17. Water safety plans: planning for adverse events and communicating with consumers.

    PubMed

    Byleveld, Paul M; Deere, Daniel; Davison, Annette

    2008-01-01

    A wide range of microbial and chemical characteristics in drinking water have the potential to affect human health. However, it is not possible or practical to test drinking water for all potentially harmful characteristics. If drinking water is contaminated, people may already be exposed by the time test results are available. The 'boil water alert' issued in Sydney, Australia in 1998 following the detection of Cryptosporidium and Giardia in the finished water supply, highlighted the uncertainties associated with the public health response to test results. The Sydney experience supports the international consensus that a preventive risk-management approach to the supply of drinking water (manifesting as water safety plans (WSPs)) is the most reliable way to protect public health. A key component of a comprehensive WSP is that water suppliers and health authorities must have plans to respond in the case of water contamination and/or outbreaks. These plans must include clear guidance on when to issue warnings to consumers, and how these warnings are to be communicated. The pressure on health authorities to develop clear and systematic boil-water guidance will increase as utilities all over the world develop their WSPs.

  18. 78 FR 51754 - Request To Modify License by Replacing Security Plan With New Radiation Safety Plan; U.S...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-08-21

    ... From the Federal Register Online via the Government Publishing Office NUCLEAR REGULATORY COMMISSION Request To Modify License by Replacing Security Plan With New Radiation Safety Plan; U.S. Department of the Army, Jefferson Proving Ground, Madison, Indiana AGENCY: Nuclear Regulatory...

  19. 12 CFR 570.3 - Filing of safety and soundness compliance plan.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... to file, or is currently operating under, a capital restoration plan submitted pursuant to section 38... 12 Banks and Banking 6 2012-01-01 2012-01-01 false Filing of safety and soundness compliance plan... plan. (a) Schedule for filing compliance plan—(1) In general. A savings association shall file...

  20. 12 CFR 570.3 - Filing of safety and soundness compliance plan.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... to file, or is currently operating under, a capital restoration plan submitted pursuant to section 38... 12 Banks and Banking 5 2011-01-01 2011-01-01 false Filing of safety and soundness compliance plan... plan. (a) Schedule for filing compliance plan—(1) In general. A savings association shall file...

  1. 12 CFR 308.303 - Filing of safety and soundness compliance plan.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... operating under, a capital restoration plan submitted pursuant to section 38 of the FDI Act (12 U.S.C. 1831o... 12 Banks and Banking 4 2011-01-01 2011-01-01 false Filing of safety and soundness compliance plan... compliance plan. (a) Schedule for filing compliance plan—(1) In general. A bank shall file a written...

  2. 12 CFR 570.3 - Filing of safety and soundness compliance plan.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... to file, or is currently operating under, a capital restoration plan submitted pursuant to section 38... 12 Banks and Banking 6 2013-01-01 2012-01-01 true Filing of safety and soundness compliance plan... plan. (a) Schedule for filing compliance plan—(1) In general. A savings association shall file...

  3. 12 CFR 170.3 - Filing of safety and soundness compliance plan.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... is obligated to file, or is currently operating under, a capital restoration plan submitted pursuant... 12 Banks and Banking 1 2013-01-01 2013-01-01 false Filing of safety and soundness compliance plan... plan. (a) Schedule for filing compliance plan— (1) In general. A Federal savings association shall...

  4. 12 CFR 308.303 - Filing of safety and soundness compliance plan.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... operating under, a capital restoration plan submitted pursuant to section 38 of the FDI Act (12 U.S.C. 1831o... 12 Banks and Banking 5 2013-01-01 2013-01-01 false Filing of safety and soundness compliance plan... compliance plan. (a) Schedule for filing compliance plan—(1) In general. A bank shall file a written...

  5. 12 CFR 308.303 - Filing of safety and soundness compliance plan.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... operating under, a capital restoration plan submitted pursuant to section 38 of the FDI Act (12 U.S.C. 1831o... 12 Banks and Banking 5 2012-01-01 2012-01-01 false Filing of safety and soundness compliance plan... compliance plan. (a) Schedule for filing compliance plan—(1) In general. A bank shall file a written...

  6. Project plan for resolution of the organic waste tank safety issues at the Hanford Site

    SciTech Connect

    Meacham, J.E.

    1996-10-03

    A multi-year project plan for the Organic Safety Project has been developed with the objective of resolving the organic safety issues associated with the High Level Waste (HLW) in Hanford`s single-shell tanks (SSTS) and double-shell tanks (DSTs). The objective of the Organic Safety Project is to ensure safe interim storage until retrieval for pretreatment and disposal operations begins, and to resolve the organic safety issues by September 2001. Since the initial identification of organics as a tank waste safety issue, progress has been made in understanding the specific aspects of organic waste combustibility, and in developing and implementing activities to resolve the organic safety issues.

  7. Home-based telemental healthcare safety planning: what you need to know.

    PubMed

    Luxton, David D; O'Brien, Karen; McCann, Russell A; Mishkind, Matthew C

    2012-10-01

    Telemental health (TMH) care provided directly to the home is an emerging area of care delivery. TMH care involves awareness of safety issues and adequate safety planning, although detailed practical recommendations for home-based TMH safety planning are absent in the literature. With this article we aim to increase awareness of safety issues associated with home-based synchronous TMH treatment and to discuss recommendations for consistent safety planning that can inform the development of standard operating procedures, emergency protocols, and overall good TMH practice. Specific areas discussed include consideration of state and local requirements, appropriateness of TMH care, technology and infrastructure, and emergency management and monitoring procedures. The topic of safety, as it relates to TMH policy, as well as the need for additional TMH research are also discussed.

  8. Home-based telemental healthcare safety planning: what you need to know.

    PubMed

    Luxton, David D; O'Brien, Karen; McCann, Russell A; Mishkind, Matthew C

    2012-10-01

    Telemental health (TMH) care provided directly to the home is an emerging area of care delivery. TMH care involves awareness of safety issues and adequate safety planning, although detailed practical recommendations for home-based TMH safety planning are absent in the literature. With this article we aim to increase awareness of safety issues associated with home-based synchronous TMH treatment and to discuss recommendations for consistent safety planning that can inform the development of standard operating procedures, emergency protocols, and overall good TMH practice. Specific areas discussed include consideration of state and local requirements, appropriateness of TMH care, technology and infrastructure, and emergency management and monitoring procedures. The topic of safety, as it relates to TMH policy, as well as the need for additional TMH research are also discussed. PMID:23061644

  9. Site safety plan for Lawrence Livermore National Laboratory CERCLA investigations at site 300. Revision 2

    SciTech Connect

    Kilmer, J.

    1997-08-01

    Various Department of Energy Orders incorporate by reference, health and safety regulations promulgated by the Occupational Safety and Health Administration (OSHA). One of the OSHA regulations, 29 CFR 1910.120, Hazardous Waste Operations and Emergency Response, requires that site safety plans are written for activities such as those covered by work plans for Site 300 environmental investigations. Based upon available data, this Site Safety Plan (Plan) for environmental restoration has been prepared specifically for the Lawrence Livermore National Laboratory Site 300, located approximately 15 miles east of Livermore, California. As additional facts, monitoring data, or analytical data on hazards are provided, this Plan may need to be modified. It is the responsibility of the Environmental Restoration Program and Division (ERD) Site Safety Officer (SSO), with the assistance of Hazards Control, to evaluate data which may impact health and safety during these activities and to modify the Plan as appropriate. This Plan is not `cast-in-concrete.` The SSO shall have the authority, with the concurrence of Hazards Control, to institute any change to maintain health and safety protection for workers at Site 300.

  10. 49 CFR 244.15 - Subjects to be addressed in a Safety Integration Plan not involving an amalgamation of operations.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Subjects to be addressed in a Safety Integration... TRANSPORTATION REGULATIONS ON SAFETY INTEGRATION PLANS GOVERNING RAILROAD CONSOLIDATIONS, MERGERS, AND ACQUISITIONS OF CONTROL Safety Integration Plans § 244.15 Subjects to be addressed in a Safety Integration...

  11. 49 CFR 244.15 - Subjects to be addressed in a Safety Integration Plan not involving an amalgamation of operations.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 4 2011-10-01 2011-10-01 false Subjects to be addressed in a Safety Integration... TRANSPORTATION REGULATIONS ON SAFETY INTEGRATION PLANS GOVERNING RAILROAD CONSOLIDATIONS, MERGERS, AND ACQUISITIONS OF CONTROL Safety Integration Plans § 244.15 Subjects to be addressed in a Safety Integration...

  12. 49 CFR 244.15 - Subjects to be addressed in a Safety Integration Plan not involving an amalgamation of operations.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 4 2012-10-01 2012-10-01 false Subjects to be addressed in a Safety Integration... TRANSPORTATION REGULATIONS ON SAFETY INTEGRATION PLANS GOVERNING RAILROAD CONSOLIDATIONS, MERGERS, AND ACQUISITIONS OF CONTROL Safety Integration Plans § 244.15 Subjects to be addressed in a Safety Integration...

  13. 49 CFR 244.15 - Subjects to be addressed in a Safety Integration Plan not involving an amalgamation of operations.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 4 2014-10-01 2014-10-01 false Subjects to be addressed in a Safety Integration... TRANSPORTATION REGULATIONS ON SAFETY INTEGRATION PLANS GOVERNING RAILROAD CONSOLIDATIONS, MERGERS, AND ACQUISITIONS OF CONTROL Safety Integration Plans § 244.15 Subjects to be addressed in a Safety Integration...

  14. 49 CFR 244.15 - Subjects to be addressed in a Safety Integration Plan not involving an amalgamation of operations.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 4 2013-10-01 2013-10-01 false Subjects to be addressed in a Safety Integration... TRANSPORTATION REGULATIONS ON SAFETY INTEGRATION PLANS GOVERNING RAILROAD CONSOLIDATIONS, MERGERS, AND ACQUISITIONS OF CONTROL Safety Integration Plans § 244.15 Subjects to be addressed in a Safety Integration...

  15. 47 CFR 90.16 - Public Safety National Plan.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... National Plan is contained in the Report and Order in General Docket No. 87-112. The principal spectrum resource for the National Plan is the 806-809 MHz and the 851-854 MHz bands at locations farther then 110... (“border regions”). In the border regions, the principal spectrum for the National Plan may be...

  16. 47 CFR 90.16 - Public Safety National Plan.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... National Plan is contained in the Report and Order in General Docket No. 87-112. The principal spectrum resource for the National Plan is the 806-809 MHz and the 851-854 MHz bands at locations farther then 110... (“border regions”). In the border regions, the principal spectrum for the National Plan may be...

  17. 47 CFR 90.16 - Public Safety National Plan.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... National Plan is contained in the Report and Order in General Docket No. 87-112. The principal spectrum resource for the National Plan is the 806-809 MHz and the 851-854 MHz bands at locations farther then 110... (“border regions”). In the border regions, the principal spectrum for the National Plan may be...

  18. 47 CFR 90.16 - Public Safety National Plan.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... National Plan is contained in the Report and Order in General Docket No. 87-112. The principal spectrum resource for the National Plan is the 806-809 MHz and the 851-854 MHz bands at locations farther then 110... (“border regions”). In the border regions, the principal spectrum for the National Plan may be...

  19. The Influence of Laboratory Safety on Capital Planning.

    ERIC Educational Resources Information Center

    Francis, Robert A.

    1980-01-01

    Discusses state and federal legislation concerning the handling of dangerous materials and its impact on the design of college and university buildings. Lists federal legislation affecting laboratory safety, the objectives of each act, and the influence of each act on laboratory safety. (IRT)

  20. 49 CFR 236.907 - Product Safety Plan (PSP).

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... description of the product functionality and information flows; (4) A safety requirements document, including... product must demonstrate that operation of the product, as modified by any predefined change, satisfies... not compromised as a result of any such change. (Software changes involving safety...

  1. Savannah River Site management response plan for chemical safety vulnerability field assessment. Revision 1

    SciTech Connect

    Kahal, E.J.; Murphy, S.L.; Salaymeh, S.R.

    1994-09-01

    As part of the U.S. Department of Energy`s (DOE) initiative to identify potential chemical safety vulnerabilities in the DOE complex, the Chemical Safety Vulnerability Core Working Group issued a field verification assessment report. While the report concluded that Savannah River Site (SRS) is moving in a positive direction, the report also identified five chemical safety vulnerabilities with broad programmatic impact that are not easily nor quickly remedied. The May 1994 SRS Management Response Plan addressed the five SRS vulnerabilities identified in the field assessment report. The SRS response plan listed observations supporting the vulnerabilities and any actions taken or planned toward resolution. Many of the observations were resolved by simple explanations, such as the existence of implementation plans for Safety Analysis Report updates. Recognizing that correcting individual observations does not suffice in remedying the vulnerabilities, a task team was assembled to address the broader programmatic issues and to recommend corrective actions.

  2. Preparation, review, and approval of implementation plans for nuclear safety requirements

    SciTech Connect

    Not Available

    1994-10-01

    This standard describes an acceptable method to prepare, review, and approve implementation plans for DOE Nuclear Safety requirements. DOE requirements are identified in DOE Rules, Orders, Notices, Immediate Action Directives, and Manuals.

  3. Best management practices plan for Phase II of the Bear Creek Valley treatability study Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

    SciTech Connect

    1997-05-01

    The Oak Ridge Y-12 Plant site is currently under a Federal Facilities Agreement to define soil and groundwater contamination and develop remedies to protect human health and the environment. The western end of the site is known to have a former nitric acid disposal pit that has been remediated and capped. Remedial investigation data indicate this pit was a source of nitrate, uranium, technetium, and other metals contamination in groundwater. The downgradient receptor of this contamination includes Bear Creek and its tributaries. A feasibility study is underway to develop a remedy to prevent further contaminant migration to this receptor. To support the feasibility study, a treatability study is being completed to examine groundwater treatment at the S-3 site. This document serves as the top level command medium for Phase II and as such will be the primary resource for management and implementation of field activities. Many of the details and standard operating procedures referred within this document can be found in other Lockheed Martin Energy Systems (Energy Systems) documents. Several supporting documents specific to this project are also cited. These include the Sampling and Analysis Plan (SAP), the Health and Safety Plan (HASP), and the Waste Management Plan (WMP). Section 1 describes the results of Phase I efforts. Section 2 describes the objectives of Phase II. Section 3 provides details of field testing. Section 4 addresses the HASP. Section 5 describes the SAP. Section 6 introduces the WMP. Environmental compliance issues are discussed in Section 7, and sediment and erosion control is addressed in Section 8. Information about the project team is provided in Section 9.

  4. 29 CFR Appendix A to Subpart P to... - Model Fire Safety Plan (Non-Mandatory)

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 29 Labor 7 2012-07-01 2012-07-01 false Model Fire Safety Plan (Non-Mandatory) A Appendix A to Subpart P to Part 1915 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH... Fire Protection in Shipyard Employment Pt. 1915, Subpt. P, App. A Appendix A to Subpart P to Part...

  5. 29 CFR Appendix A to Subpart P of... - Model Fire Safety Plan (Non-Mandatory)

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 29 Labor 7 2014-07-01 2014-07-01 false Model Fire Safety Plan (Non-Mandatory) A Appendix A to Subpart P of Part 1915 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH... Fire Protection in Shipyard Employment Pt. 1915, Subpt. P, App. A Appendix A to Subpart P of Part...

  6. 29 CFR Appendix A to Subpart P to... - Model Fire Safety Plan (Non-Mandatory)

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 29 Labor 7 2011-07-01 2011-07-01 false Model Fire Safety Plan (Non-Mandatory) A Appendix A to Subpart P to Part 1915 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH... Fire Protection in Shipyard Employment Pt. 1915, Subpt. P, App. A Appendix A to Subpart P to Part...

  7. Integrated Environment and Safety and Health Management System (ISMS) Implementation Project Plan

    SciTech Connect

    MITCHELL, R.L.

    2000-01-10

    The Integrated Environment, Safety and Health Management System (ISMS) Implementation Project Plan serves as the project document to guide the Fluor Hanford, Inc (FHI) and Major Subcontractor (MSC) participants through the steps necessary to complete the integration of environment, safety, and health into management and work practices at all levels.

  8. The Use of Safety Plans with Children and Adolescents Living in Violent Families

    ERIC Educational Resources Information Center

    Kress, Victoria E.; Adamson, Nicole A.; Paylo, Matthew J.; DeMarco, Carrie; Bradley, Nicole

    2012-01-01

    Counselors are regularly confronted with children and adolescents who reside in violent or potentially violent living environments. In this article, safety plans are presented as a tool that counselors can use to promote the safety of children living in unsafe family situations. Ethics-related counseling issues that should be considered when…

  9. Health and safety plan for characterization sampling of ETR and MTR facilities

    SciTech Connect

    Baxter, D.E.

    1994-10-01

    This health and safety plan establishes the procedures and requirements that will be used to minimize health and safety risks to persons performing Engineering Test Reactor and Materials Test Reactor characterization sampling activities, as required by the Occupational Safety and Health Administration standard, 29 CFR 1910.120. It contains information about the hazards involved in performing the tasks, and the specific actions and equipment that will be used to protect persons working at the site.

  10. 47 CFR 90.16 - Public Safety National Plan.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... National Plan is contained in the Report and Order in General Docket No. 87-112. The principal spectrum... (“border regions”). In the border regions, the principal spectrum for the National Plan may be different..., and the U.S. Virgin Islands. No assignments will be made in the spectrum designated for the...

  11. Life safety in the perianesthesia care environment: planning for internal disasters.

    PubMed

    Sullivan, E

    2000-06-01

    Nurses in perianesthesia areas have a critical responsibility to provide a well thought-out safety plan in the event of internal disaster. Working together as a team, identifying key people, assigning responsibilities, and communicating the plan will prepare the staff to efficiently manage the unexpected event. PMID:11249340

  12. Final Action Plan to Tiger Team. Environmental, safety and health assessment

    SciTech Connect

    Not Available

    1992-02-28

    This document presents planned actions, and their associated costs, for addressing the findings in the Environmental, Safety and Health Tiger Team Assessment of the Sandia National Laboratories, Albuquerque, May 1991, hereafter called the Assessment. This Final Action Plan should be read in conjunction with the Assessment to ensure full understanding of the findings addressed herein. The Assessment presented 353 findings in four general categories: (1)Environmental (82 findings); (2) Safety and Health (243 findings); (3) Management and Organization (18 findings); and (4) Self-Assessment (10 findings). Additionally, 436 noncompliance items with Occupational Safety and Health Administration (OSHA) standards were addressed during and immediately after the Tiger Team visit.

  13. Haptics-assisted Virtual Planning of Bone, Soft Tissue, and Vessels in Fibula Osteocutaneous Free Flaps

    PubMed Central

    Nysjö, Fredrik; Rodríguez-Lorenzo, Andrés; Thor, Andreas; Hirsch, Jan-Michaél; Carlbom, Ingrid B.

    2015-01-01

    Background: Virtual surgery planning has proven useful for reconstructing head and neck defects by fibula osteocutaneous free flaps (FOFF). Benefits include improved healing, function, and aesthetics, as well as cost savings. But available virtual surgery planning systems incorporating fibula in craniomaxillofacial reconstruction simulate only bone reconstruction without considering vessels and soft tissue. Methods: The Haptics-Assisted Surgery Planning (HASP) system incorporates bone, vessels, and soft tissue of the FOFF in craniomaxillofacial defect reconstruction. Two surgeons tested HASP on 4 cases they had previously operated on: 3 with composite mandibular defects and 1 with a composite cervical spine defect. With the HASP stereographics and haptic feedback, using patient-specific computed tomography angiogram data, the surgeons planned the 4 cases, including bone resection, fibula design, recipient vessels selection, pedicle and perforator location selection, and skin paddle configuration. Results: Some problems encountered during the actual surgery could have been avoided as they became evident with HASP. In one case, the fibula reconstruction was incomplete because the fibula had to be reversed and thus did not reach the temporal fossa. In another case, the fibula had to be rotated 180 degrees to correct the plate and screw placement in relation to the perforator. In the spinal case, difficulty in finding the optimal fibula shape and position required extra ischemia time. Conclusions: The surgeons found HASP to be an efficient planning tool for FOFF reconstructions. The testing of alternative reconstructions to arrive at an optimal FOFF solution preoperatively potentially improves patient function and aesthetics and reduces operating room time. PMID:26495192

  14. Advanced spacecraft fire safety: Proposed projects and program plan

    NASA Technical Reports Server (NTRS)

    Youngblood, Wallace W.; Vedha-Nayagam, M.

    1989-01-01

    A detailed review identifies spacecraft fire safety issues and the efforts for their resolution, particularly for the threats posed by the increased on-orbit duration, size, and complexity of the Space Station Freedom. Suggestions provided by a survey of Wyle consultants and outside fire safety experts were combined into 30 research and engineering projects. The projects were then prioritized with respect to urgency to meet Freedom design goals, status of enabling technology, cost, and so on, to yield 14 highest priority projects, described in terms of background, work breakdown structure, and schedule. These highest priority projects can be grouped into the thematic areas of fire detection, fire extinguishment, risk assessment, toxicology and human effects, and ground based testing. Recommendations for overall program management stress the need for NASA Headquarters and field center coordination, with information exchange through spacecraft fire safety oversight committees.

  15. 49 CFR 659.19 - System safety program plan: contents.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... ensure they are achieved. (c) An overview of the management structure of the rail transit agency... rest of the rail transit organization; and (3) Clear identification of the lines of authority used by the rail transit agency to manage safety issues. (d) The process used to control changes to the...

  16. 49 CFR 659.19 - System safety program plan: contents.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... ensure they are achieved. (c) An overview of the management structure of the rail transit agency... rest of the rail transit organization; and (3) Clear identification of the lines of authority used by the rail transit agency to manage safety issues. (d) The process used to control changes to the...

  17. 49 CFR 659.19 - System safety program plan: contents.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... ensure they are achieved. (c) An overview of the management structure of the rail transit agency... rest of the rail transit organization; and (3) Clear identification of the lines of authority used by the rail transit agency to manage safety issues. (d) The process used to control changes to the...

  18. 49 CFR 659.19 - System safety program plan: contents.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... ensure they are achieved. (c) An overview of the management structure of the rail transit agency... rest of the rail transit organization; and (3) Clear identification of the lines of authority used by the rail transit agency to manage safety issues. (d) The process used to control changes to the...

  19. The Impact of Terrorism on School Safety Planning.

    ERIC Educational Resources Information Center

    Trump, Kenneth S.

    2002-01-01

    Discusses why history and "thinking outside of the box" should encourage schools to acknowledge that they are potentially vulnerable targets of terrorism. Presents new safety and security issues raised by the threat of terrorism, including anthrax scares, cell phone use, and field trips. Describes "heightened security" procedures and crisis…

  20. An Online Resource for Flight Test Safety Planning

    NASA Technical Reports Server (NTRS)

    Lewis, Greg

    2007-01-01

    A viewgraph presentation describing an online database for flight test safety techniques is shown. The topics include: 1) Goal; 2) Test Hazard Analyses; 3) Online Database Background; 4) Data Gathering; 5) NTPS Role; 6) Organizations; 7) Hazard Titles; 8) FAR Paragraphs; 9) Maneuver Name; 10) Identified Hazard; 11) Matured Hazard Titles; 12) Loss of Control Causes; 13) Mitigations; 14) Database Now Open to the Public; 15) FAR Reference Search; 16) Record Field Search; 17) Keyword Search; and 18) Results of FAR Reference Search.

  1. Draft safety review plan for accelerator production of tritium (APT) project

    SciTech Connect

    1997-07-01

    The purpose of this ``living`` Safety Review Plan (SRP) is to describe the products and processes that will be followed to conduct a systematic review of the Accelerator Production of Tritium (APT) Facility Preliminary Safety Analysis Report (PSAR), and subsequently to prepare a draft Safety Evaluation Report (SER) on the PSAR. This plan is prepared for and will be implemented by the APT Independent Safety Review Committee (ISRC) over the period July 1, 1997 through September 30, 1998, in accordance with provisions established in DOE-STD-1104-96. A core team of DOE, INEEL, and AMPARO Corporation engineers and scientists will prepare the initial draft SER with assistance from other ISRC team members on an as needed basis. Guidelines for preparing the draft SER are presented in Section 7 of this SRP. The PSAR reviews will focus exclusively on safety. The ever-present two-part question will be: Does the subject matter have safety significance? If so, does the APT structural, system, component, and/or process engineering design ensure an acceptable margin of safety? The APT mission, efficiency, and cost are not considerations of this plan. A more detailed discussion of the review philosophy is presented in Section 5 of this SRP.

  2. A hybrid simulation approach for integrating safety behavior into construction planning: An earthmoving case study.

    PubMed

    Goh, Yang Miang; Askar Ali, Mohamed Jawad

    2016-08-01

    One of the key challenges in improving construction safety and health is the management of safety behavior. From a system point of view, workers work unsafely due to system level issues such as poor safety culture, excessive production pressure, inadequate allocation of resources and time and lack of training. These systemic issues should be eradicated or minimized during planning. However, there is a lack of detailed planning tools to help managers assess the impact of their upstream decisions on worker safety behavior. Even though simulation had been used in construction planning, the review conducted in this study showed that construction safety management research had not been exploiting the potential of simulation techniques. Thus, a hybrid simulation framework is proposed to facilitate integration of safety management considerations into construction activity simulation. The hybrid framework consists of discrete event simulation (DES) as the core, but heterogeneous, interactive and intelligent (able to make decisions) agents replace traditional entities and resources. In addition, some of the cognitive processes and physiological aspects of agents are captured using system dynamics (SD) approach. The combination of DES, agent-based simulation (ABS) and SD allows a more "natural" representation of the complex dynamics in construction activities. The proposed hybrid framework was demonstrated using a hypothetical case study. In addition, due to the lack of application of factorial experiment approach in safety management simulation, the case study demonstrated sensitivity analysis and factorial experiment to guide future research.

  3. A hybrid simulation approach for integrating safety behavior into construction planning: An earthmoving case study.

    PubMed

    Goh, Yang Miang; Askar Ali, Mohamed Jawad

    2016-08-01

    One of the key challenges in improving construction safety and health is the management of safety behavior. From a system point of view, workers work unsafely due to system level issues such as poor safety culture, excessive production pressure, inadequate allocation of resources and time and lack of training. These systemic issues should be eradicated or minimized during planning. However, there is a lack of detailed planning tools to help managers assess the impact of their upstream decisions on worker safety behavior. Even though simulation had been used in construction planning, the review conducted in this study showed that construction safety management research had not been exploiting the potential of simulation techniques. Thus, a hybrid simulation framework is proposed to facilitate integration of safety management considerations into construction activity simulation. The hybrid framework consists of discrete event simulation (DES) as the core, but heterogeneous, interactive and intelligent (able to make decisions) agents replace traditional entities and resources. In addition, some of the cognitive processes and physiological aspects of agents are captured using system dynamics (SD) approach. The combination of DES, agent-based simulation (ABS) and SD allows a more "natural" representation of the complex dynamics in construction activities. The proposed hybrid framework was demonstrated using a hypothetical case study. In addition, due to the lack of application of factorial experiment approach in safety management simulation, the case study demonstrated sensitivity analysis and factorial experiment to guide future research. PMID:26456000

  4. Traffic Safety Planning on School Sites. A Technical Project.

    ERIC Educational Resources Information Center

    Institute of Transportation Engineers, Lansing, MI. Michigan Section.

    Control of traffic around school areas is one of the most important factors to be considered when selecting and designing a school site plan. To provide positive safeguards, it is necessary to establish and encourage school administrators to adopt a comprehensive set of guidelines. This booklet is directed to all personnel involved either in…

  5. Department of Energy Environment, Safety and Health Management Plan. Fiscal year 1996

    SciTech Connect

    1996-01-01

    This report describes efforts by the Department of Energy (DOE) to effectively plan for environment, safety and health activities that protect the environment, workers and the public from harm. This document, which covers fiscal year 1996, reflects planning by operating contractors and Program Offices in early 1994, updated to be consistent with the President`s FY 1996 budget submittal to Congress, and subsequent Department of Energy Program refinements. Prior to 1992, only a small number of facilities had a structured process for identifying environment, safety and health (ES and H) needs, reporting the costs (in both direct and indirect budgets) of ES and H requirements, prioritizing and allocating available resources, and efficiently communicating this information to DOE. Planned costs for ES and H activities were usually developed as an afterthought to program budgets. There was no visible, consistently applied mechanism for determining the appropriate amount of resources that should be allocated to ES and H, or for assuring that significant ES and H vulnerabilities were planned to be funded. To address this issue, the Secretary (in November 1991) directed DOE to develop a Safety and Health Five-Year Plan to serve as a line management tool to delineate DOE-wide programs to reduce and manage safety and health risks, and to establish a consistent framework for risk-based resource planning and allocation.

  6. 78 FR 59754 - Notice of Application for Approval of Railroad Safety Program Plan and Product Safety Plan

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-09-27

    ... railroad productivity and significantly improving the safety of train operations, roadway workers, and... individual submitting the comment (or signing the document, if submitted on behalf of an association... published on April 11, 2000 (65 FR 19477). Robert C. Lauby, Deputy Associate Administrator for...

  7. 76 FR 72980 - Occupational Safety and Health State Plans; Extension of the Office of Management and Budget's...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-11-28

    ... Occupational Safety and Health Administration Occupational Safety and Health State Plans; Extension of the Office of Management and Budget's (OMB) Approval of Information Collection (Paperwork) Requirements... and Budget's (OMB) approval of the information collection requirements associated with its...

  8. Facility Safety Plan B360 Complex Biohazardous Operations CMLS-412r0

    SciTech Connect

    Cooper, G

    2007-01-08

    This Addendum to the Facility Safety Plan (FSP) 360 Complex describes the safety requirements for the safe conduct of all biohazardous research operations in all buildings within the 360 complex program areas. These requirements include all the responsibilities and authorities of building personnel, operational hazards, and environmental concerns and their controls. In addition, this Addendum prescribes facility-specific training requirements and emergency controls, as well as maintenance and quality assurance requirements for ES&H-related building systems.

  9. Narrative Practice and the Signs of Safety Approach: Engaging Adolescents in Building Rigorous Safety Plans

    ERIC Educational Resources Information Center

    Gibson, Matthew

    2014-01-01

    The Signs of Safety approach to child protection has been gaining prominence around the world and this approach has developed through learning from good practice. Generally, examples of good practice are derived from adults who pose a risk to children, while this paper outlines an example of good practice that engages an adolescent in building a…

  10. Phase II -- Photovoltaics for Utility Scale Applications (PVUSA): Safety and health action plan

    SciTech Connect

    Berg, K.

    1994-09-01

    To establish guidelines for the implementation and administration of an injury and illness prevention program for PVUSA and to assign specific responsibilities for the execution of the program. To provide a basic Safety and Health Action Plan (hereinafter referred to as Plan) that assists management, supervision, and project personnel in the recognition, evaluation, and control of hazardous activities and/or conditions within their respective areas of responsibility.

  11. Breckinridge Project, initial effort. Report VII, Volume 4. Safety and health plan

    SciTech Connect

    1982-01-01

    The Safety and Health Plan recognizes the potential hazards associated with the Project and has been developed specifically to respond to these risks in a positive manner. Prevention, the primary objective of the Plan, starts with building safety controls into the process design and continues through engineering, construction, start-up, and operation of the Project facilities and equipment. Compliance with applicable federal, state, and local health and safety laws, regulations, and codes throughout all Project phases is required and assured. The Plan requires that each major Project phase be thoroughly reviewed and analyzed to determine that those provisions required to assure the safety and health of all employees and the public, and to prevent property and equipment losses, have been provided. The Plan requires followup on those items or situations where corrective action needs were identified to assure that the action was taken and is effective. Emphasis is placed on loss prevention. Exhibit 1 provides a breakdown of Ashland Synthetic Fuels, Inc.'s (ASFI's) Loss Prevention Program. The Plan recognizes that the varied nature of the work is such as to require the services of skilled, trained, and responsible personnel who are aware of the hazards and know that the work can be done safely, if done correctly. Good operating practice is likewise safe operating practice. Training is provided to familiarize personnel with good operational practice, the general sequence of activities, reporting requirements, and above all, the concept that each step in the operating procedures must be successfully concluded before the following step can be safely initiated. The Plan provides for periodic review and evaluation of all safety and loss prevention activities at the plant and departmental levels.

  12. Laser programs facility management plan for environment, safety, and health

    SciTech Connect

    Cruz, G.E.

    1996-01-01

    The Lawrence Livermore National Laboratory`s (LLNL) Laser Programs ES&H policy is established by the Associate Director for Laser Programs. This FMP is one component of that policy. Laser Programs personnel design, construct and operate research and development equipment located in various Livermore and Site 300 buildings. The Programs include a variety of activities, primarily laser research and development, inertial confinement fusion, isotope separation, and an increasing emphasis on materials processing, imaging systems, and signal analysis. This FMP is a formal statement of responsibilities and controls to assure operational activities are conducted without harm to employees, the general public, or the environment. This plan identifies the hazards associated with operating a large research and development facility and is a vehicle to control and mitigate those hazards. Hazards include, but are not limited to: laser beams, hazardous and radioactive materials, criticality, ionizing radiation or x rays, high-voltage electrical equipment, chemicals, and powered machinery.

  13. Sodium fast reactor safety and licensing research plan. Volume I.

    SciTech Connect

    Sofu, Tanju; LaChance, Jeffrey L.; Bari, R.; Wigeland, Roald; Denman, Matthew R.; Flanagan, George F.

    2012-05-01

    This report proposes potential research priorities for the Department of Energy (DOE) with the intent of improving the licensability of the Sodium Fast Reactor (SFR). In support of this project, five panels were tasked with identifying potential safety-related gaps in available information, data, and models needed to support the licensing of a SFR. The areas examined were sodium technology, accident sequences and initiators, source term characterization, codes and methods, and fuels and materials. It is the intent of this report to utilize a structured and transparent process that incorporates feedback from all interested stakeholders to suggest future funding priorities for the SFR research and development. While numerous gaps were identified, two cross-cutting gaps related to knowledge preservation were agreed upon by all panels and should be addressed in the near future. The first gap is a need to re-evaluate the current procedures for removing the Applied Technology designation from old documents. The second cross-cutting gap is the need for a robust Knowledge Management and Preservation system in all SFR research areas. Closure of these and the other identified gaps will require both a reprioritization of funding within DOE as well as a re-evaluation of existing bureaucratic procedures within the DOE associated with Applied Technology and Knowledge Management.

  14. SAFETY AND SECURITY BUILDING, TRA614. FLOOR, ROOF, AND FOUNDATION PLANS. ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    SAFETY AND SECURITY BUILDING, TRA-614. FLOOR, ROOF, AND FOUNDATION PLANS. ROOM FUNCTIONS. DOOR AND ROOM FINISH SCHEDULE. BLAW-KNOX 3150-814-1, 3/1950. INL INDEX NO. 531-0614-00-098-100702, REV. 6. - Idaho National Engineering Laboratory, Test Reactor Area, Materials & Engineering Test Reactors, Scoville, Butte County, ID

  15. The Tennis Ball Bomb Incident or the Safety Plan as "Shelf Document"

    ERIC Educational Resources Information Center

    Fast, Jonathan; Fanelli, Rossella

    2003-01-01

    This article presents a case study of a single incident involving a high school student who brought a "tennis ball" bomb to school. Although the district had recently created a safety plan, with a specific protocol for the discovery of a bomb in the building, the principal and the crises team ignored it. The principal did not refer to the safety…

  16. 76 FR 55056 - Toy Safety Standard: Strategic Outreach and Education Plan

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-09-06

    ...The Consumer Product Safety Commission (``CPSC,'' ``Commission,'' or ``we'') is announcing the development of a strategic outreach and education plan to help the business community and other stakeholders learn about testing and certification requirements for children's toys and toy chests and their compliance with ASTM International's (formerly the American Society for Testing and Materials)......

  17. K Basin sludge packaging design criteria (PDC) and safety analysis report for packaging (SARP) approval plan

    SciTech Connect

    Brisbin, S.A.

    1996-03-06

    This document delineates the plan for preparation, review, and approval of the Packaging Design Crieteria for the K Basin Sludge Transportation System and the Associated on-site Safety Analysis Report for Packaging. The transportation system addressed in the subject documents will be used to transport sludge from the K Basins using bulk packaging.

  18. 49 CFR 236.1015 - PTC Safety Plan content requirements and PTC System Certification.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... INSTRUCTIONS GOVERNING THE INSTALLATION, INSPECTION, MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Positive Train Control Systems § 236.1015 PTC Safety Plan content... established and can maintain a quality control system for PTC system design and manufacturing acceptable...

  19. 78 FR 979 - Petition for Positive Train Control Safety Plan Approval and System Certification of the...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-01-07

    ... Federal Railroad Administration Petition for Positive Train Control Safety Plan Approval and System Certification of the Electronic Train Management System In accordance with Part 211 of Title 49 Code of Federal... Railway (BNSF) has petitioned the Federal Railroad Administration (FRA) for Positive Train Control...

  20. Health and Safety Management Plan for the Plutonium Stabilization and Packaging System

    SciTech Connect

    1996-06-04

    This Health and Safety Management Plan (HSMP) presents safety and health policies and a project health and safety organizational structure designed to minimize potential risks of harm to personnel performing activities associated with Plutonium Stabilization and Packaging System (Pu SPS). The objectives of the Pu SPS are to design, fabricate, install, and startup of a glovebox system for the safe repackaging of plutonium oxides and metals, with a requirement of a 50-year storage period. This HSMP is intended as an initial project health and safety submittal as part of a three phase effort to address health and safety issues related to personnel working the Pu SPS project. Phase 1 includes this HSMP and sets up the basic approach to health and safety on the project and addresses health and safety issues related to the engineering and design effort. Phase 2 will include the Site Specific Construction health and Safety Plan (SSCHSP). Phase 3 will include an additional addendum to this HSMP and address health and safety issues associated with the start up and on-site test phase of the project. This initial submittal of the HSMP is intended to address those activities anticipated to be performed during phase 1 of the project. This HSMP is intended to be a living document which shall be modified as information regarding the individual tasks associated with the project becomes available. These modifications will be in the form of addenda to be submitted prior to the initiation of each phase of the project. For additional work authorized under this project this HSMP will be modified as described in section 1.4.

  1. RISMC Advanced Safety Analysis Project Plan – FY 2015 - FY 2019

    SciTech Connect

    Szilard, Ronaldo H.; Smith, Curtis L.; Youngblood, Robert

    2014-09-01

    In this report, a project plan is developed, focused on industry applications, using Risk-Informed Safety Margin Characterization (RISMC) tools and methods applied to realistic, relevant, and current interest issues to the operating nuclear fleet. RISMC focuses on modernization of nuclear power safety analysis (tools, methods and data); implementing state-of-the-art modeling techniques (which include, for example, enabling incorporation of more detailed physics as they become available); taking advantage of modern computing hardware; and combining probabilistic and mechanistic analyses to enable a risk informed safety analysis process. The modernized tools will maintain the current high level of safety in our nuclear power plant fleet, while providing an improved understanding of safety margins and the critical parameters that affect them. Thus, the set of tools will provide information to inform decisions on plant modifications, refurbishments, and surveillance programs, while improving economics. This set of tools will also benefit the design of new reactors, enhancing safety per unit cost of a nuclear plant. The proposed plan will focus on application of the RISMC toolkit, in particular, solving realistic problems of important current issues to the nuclear industry, in collaboration with plant owners and operators to demonstrate the usefulness of these tools in decision making.

  2. 48 CFR 970.5223-1 - Integration of environment, safety, and health into work planning and execution.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 48 Federal Acquisition Regulations System 5 2013-10-01 2013-10-01 false Integration of environment... Integration of environment, safety, and health into work planning and execution. As prescribed in 970.2303-3(b), insert the following clause: Integration of Environment, Safety, and Health Into Work Planning...

  3. 48 CFR 952.223-71 - Integration of environment, safety, and health into work planning and execution.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 48 Federal Acquisition Regulations System 5 2014-10-01 2014-10-01 false Integration of environment, safety, and health into work planning and execution. 952.223-71 Section 952.223-71 Federal Acquisition... Provisions and Clauses 952.223-71 Integration of environment, safety, and health into work planning...

  4. 48 CFR 952.223-71 - Integration of environment, safety, and health into work planning and execution.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 48 Federal Acquisition Regulations System 5 2013-10-01 2013-10-01 false Integration of environment, safety, and health into work planning and execution. 952.223-71 Section 952.223-71 Federal Acquisition... Provisions and Clauses 952.223-71 Integration of environment, safety, and health into work planning...

  5. 48 CFR 970.5223-1 - Integration of environment, safety, and health into work planning and execution.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 48 Federal Acquisition Regulations System 5 2014-10-01 2014-10-01 false Integration of environment... Integration of environment, safety, and health into work planning and execution. As prescribed in 970.2303-3(b), insert the following clause: Integration of Environment, Safety, and Health Into Work Planning...

  6. 48 CFR 952.223-71 - Integration of environment, safety, and health into work planning and execution.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 5 2012-10-01 2012-10-01 false Integration of environment, safety, and health into work planning and execution. 952.223-71 Section 952.223-71 Federal Acquisition... Provisions and Clauses 952.223-71 Integration of environment, safety, and health into work planning...

  7. 48 CFR 970.5223-1 - Integration of environment, safety, and health into work planning and execution.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 48 Federal Acquisition Regulations System 5 2012-10-01 2012-10-01 false Integration of environment... Integration of environment, safety, and health into work planning and execution. As prescribed in 970.2303-3(b), insert the following clause: Integration of Environment, Safety, and Health Into Work Planning...

  8. 48 CFR 970.5223-1 - Integration of environment, safety, and health into work planning and execution.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 5 2011-10-01 2011-10-01 false Integration of environment... Integration of environment, safety, and health into work planning and execution. As prescribed in 970.2303-3(b), insert the following clause: Integration of Environment, Safety, and Health Into Work Planning...

  9. 48 CFR 952.223-71 - Integration of environment, safety, and health into work planning and execution.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 5 2011-10-01 2011-10-01 false Integration of environment, safety, and health into work planning and execution. 952.223-71 Section 952.223-71 Federal Acquisition... Provisions and Clauses 952.223-71 Integration of environment, safety, and health into work planning...

  10. 48 CFR 952.223-71 - Integration of environment, safety, and health into work planning and execution.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Integration of environment, safety, and health into work planning and execution. 952.223-71 Section 952.223-71 Federal Acquisition... Provisions and Clauses 952.223-71 Integration of environment, safety, and health into work planning...

  11. 48 CFR 970.5223-1 - Integration of environment, safety, and health into work planning and execution.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Integration of environment... Integration of environment, safety, and health into work planning and execution. As prescribed in 970.2303-3(b), insert the following clause: Integration of Environment, Safety, and Health Into Work Planning...

  12. A Logical Approach to Designing Safety Test Plans for Space Nuclear Systems

    SciTech Connect

    Coleman, James R

    2004-02-04

    This paper presents a logical approach to designing a safety test plan for a space nuclear system. It is pointed out that two important facts need to underlie the development of a test plan: first, that sequential insults and the accumulation of damage are the rule; and second that the response of the nuclear system is stochastic (i.e., for any given set of conditions a probabilistic range of outcomes will occur regardless of the state of our knowledge). Because of these facts a deterministic approach can only be a starting point. The substance of the approach consists of undertaking and documenting three basic efforts: (1) a description of the analysts view of the problem and how it fits into the safety analysis, (2) a formal documentation of the purpose and requirements of the test plan (or test), and (3) an assessment of the use or usefulness of existing test data.

  13. Environmental restoration and waste management department independent safety review committee program management plan

    SciTech Connect

    Not Available

    1992-10-01

    This Program Management Plan (PMP) describes and governs the Independent Safety Review Committee (ISRC) established within the Environmental Restoration and Waste Management Department (ER WMD). The ISRC performs independent safety reviews for the ER WMD as required and specified by the governing documents mentioned above. This PMP defines the ISRC organization, work plan, and scope of work. The PMP is organized consistent with the requirements of DOE Order 4700.1, Project Management System. For the purpose of readability, this document shall use the term program'' to include not only the chartered activities of the ISRC, but also the related activities conducted by the chairman and staff. This PMP is subordinate to the ER WMD Implementing Program Management Plan, EGG-WM-10220.

  14. Environmental restoration and waste management department independent safety review committee program management plan

    SciTech Connect

    Not Available

    1992-10-01

    This Program Management Plan (PMP) describes and governs the Independent Safety Review Committee (ISRC) established within the Environmental Restoration and Waste Management Department (ER&WMD). The ISRC performs independent safety reviews for the ER&WMD as required and specified by the governing documents mentioned above. This PMP defines the ISRC organization, work plan, and scope of work. The PMP is organized consistent with the requirements of DOE Order 4700.1, Project Management System. For the purpose of readability, this document shall use the term ``program`` to include not only the chartered activities of the ISRC, but also the related activities conducted by the chairman and staff. This PMP is subordinate to the ER&WMD Implementing Program Management Plan, EGG-WM-10220.

  15. SARS and health worker safety: lessons for influenza pandemic planning and response.

    PubMed

    Possamai, Mario A

    2007-01-01

    The outbreak of severe acute respiratory syndrome (SARS) in 2003 provided valuable lessons for protecting health workers during an influenza pandemic or other public health crisis. In its final report, the SARS Commission concluded that a key lesson in worker safety was the precautionary principle. It stated that reasonable actions to reduce risk should not await scientific certainty. As recommended by the SARS Commission, this principle has now been enshrined in the Health Protection and Promotion Act (2007), Ontario's public health legislation and in Ontario's influenza pandemic plan. Another vital lesson for worker safety involves the occupational hygiene concept of a hierarchy of controls. It takes a holistic approach to worker safety, addressing each hazard through control at the source of the hazard, along the path between the worker and the hazard and, lastly, at the worker. Absent such an approach, the SARS Commission said worker safety may focus solely on a particular piece of personal protective equipment, such as an N95 respirator (important as it may be), or on specific policies and procedures, such as fit testing the N95 respirator to the wearer (significant as it may be). In worker safety, said the commission, the integrated whole is greater than the uncoordinated parts. The third and final worker safety lesson of SARS is the importance of having a robust safety culture in the workplace in which workers play an integral role in promoting a safe workplace. PMID:18030033

  16. National Ignition Facility start-up/operations engineering and special equipment construction health and safety plan

    SciTech Connect

    Huddleston, P C

    1998-05-08

    This document sets forth the responsibilities, interfaces, guidelines, rules, policy, and regulations for all workers involved in the S/O and SE construction, installation, and acceptance testing. This document is enforced from the first day that S/O and SE workers set foot on the NIF construction site until the end of the Project at Critical Decision 4. This document is applicable only to site activities, which are defined as those that occur within the perimeter of the fenced-off NIF construction zone and the Target Chamber Assembly Area (Helipad). The associated Special Equipment laydown and construction support areas listed in Appendix B are not under this plan; their safety provisions are discussed in the Appendix. Prototype and other support activities, such as the Amplifier Laboratory and Frame Assembly Unit assembly area, are not included in this plan. After completion of the Operational Readiness Review, the Facility Safety Procedure, Operational Safety Requirements, and Operational Safety Procedures are the governing safety documents for the operating facility. The S/O and SE project elements are required to implement measures that create a universal awareness of and promote safe job practices at the site. This includes all Lawrence Livermore National Laboratory (LLNL), Los Alamos National Laboratory, Sandia National Laboratories, University of Rochester, supplement labor organization, and subcontractor employees; visitors; and guests serving the S/O and SE effort.

  17. There is more to risk and safety planning than dramatic risks: Mental health nurses' risk assessment and safety-management practice.

    PubMed

    Higgins, Agnes; Doyle, Louise; Downes, Carmel; Morrissey, Jean; Costello, Paul; Brennan, Michael; Nash, Michael

    2016-04-01

    Risk assessment and safety planning are considered a cornerstone of mental health practice, yet limited research exists into how mental health nurses conceptualize 'risk' and how they engage with risk assessment and safety planning. The aim of the present study was to explore mental health nurses' practices and confidence in risk assessment and safety planning. A self-completed survey was administered to 381 mental health nurses in Ireland. The findings indicate that nurses focus on risk to self and risk to others, with the risk of suicide, self-harm, substance abuse, and violence being most frequently assessed. Risk from others and 'iatrogenic' risk were less frequently considered. Overall, there was limited evidence of recovery-oriented practice in relation to risk. The results demonstrate a lack of meaningful engagement with respect to collaborative safety planning, the identification and inclusion of protective factors, and the inclusion of positive risk-taking opportunities. In addition, respondents report a lack of confidence working with positive risk taking and involving family/carers in the risk-assessment and safety-planning process. Gaps in knowledge about risk-assessment and safety-planning practice, which could be addressed through education, are identified, as are the implications of the findings for practice and research.

  18. Work plan and health and safety plan for Building 3019B underground storage tank at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect

    Burman, S.N.; Brown, K.S.; Landguth, D.C.

    1992-08-01

    As part of the Underground Storage Tank Program at the Department of Energy`s Oak Ridge National Laboratory (ORNL) in Oak Ridge, Tennessee, this Health and Safety Plan has been developed for removal of the 110-gal leaded fuel underground storage tank (UST) located in the Building 3019B area at ORNL This Health and Safety Plan was developed by the Measurement Applications and Development Group of the Health and Safety Research Division at ORNL The major components of the plan follow: (1) A project description that gives the scope and objectives of the 110-gal tank removal project and assigns responsibilities, in addition to providing emergency information for situations occurring during field operations; (2) a health and safety plan in Sect. 15 for the Building 3019B UST activities, which describes general site hazards and particular hazards associated with specific tasks, personnel protection requirements and mandatory safety procedures; and (3) discussion of the proper form completion and reporting requirements during removal of the UST. This document addresses Occupational Safety and Health Administration (OSHA) requirements in 29 CFR 1910.120 with respect to all aspects of health and safety involved in a UST removal. In addition, the plan follows the Environmental Protection Agency (EPA) QAMS 005/80 (1980) format with the inclusion of the health and safety section (Sect. 15).

  19. Work plan and health and safety plan for Building 3019B underground storage tank at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect

    Burman, S.N.; Brown, K.S.; Landguth, D.C.

    1992-08-01

    As part of the Underground Storage Tank Program at the Department of Energy's Oak Ridge National Laboratory (ORNL) in Oak Ridge, Tennessee, this Health and Safety Plan has been developed for removal of the 110-gal leaded fuel underground storage tank (UST) located in the Building 3019B area at ORNL This Health and Safety Plan was developed by the Measurement Applications and Development Group of the Health and Safety Research Division at ORNL The major components of the plan follow: (1) A project description that gives the scope and objectives of the 110-gal tank removal project and assigns responsibilities, in addition to providing emergency information for situations occurring during field operations; (2) a health and safety plan in Sect. 15 for the Building 3019B UST activities, which describes general site hazards and particular hazards associated with specific tasks, personnel protection requirements and mandatory safety procedures; and (3) discussion of the proper form completion and reporting requirements during removal of the UST. This document addresses Occupational Safety and Health Administration (OSHA) requirements in 29 CFR 1910.120 with respect to all aspects of health and safety involved in a UST removal. In addition, the plan follows the Environmental Protection Agency (EPA) QAMS 005/80 (1980) format with the inclusion of the health and safety section (Sect. 15).

  20. Nuclear safety

    NASA Technical Reports Server (NTRS)

    Buden, D.

    1991-01-01

    Topics dealing with nuclear safety are addressed which include the following: general safety requirements; safety design requirements; terrestrial safety; SP-100 Flight System key safety requirements; potential mission accidents and hazards; key safety features; ground operations; launch operations; flight operations; disposal; safety concerns; licensing; the nuclear engine for rocket vehicle application (NERVA) design philosophy; the NERVA flight safety program; and the NERVA safety plan.

  1. Management response plan for the Chemical Safety Vulnerability Working Group report. Volume 2

    SciTech Connect

    Not Available

    1994-09-01

    The Chemical Safety Vulnerability (CSV) Working Group was established to identify adverse conditions involving hazardous chemicals at DOE facilities that might result in fires or explosions, release of hazardous chemicals to the environment, or exposure of workers or the public to chemicals. A CSV Review was conducted in 146 facilities at 29 sites. Eight generic vulnerabilities were documented related to: abandoned chemicals and chemical residuals; past chemical spills and ground releases; characterization of legacy chemicals and wastes; disposition of legacy chemicals; storage facilities and conditions; condition of facilities and support systems; unanalyzed and unaddressed hazards; and inventory control and tracking. Weaknesses in five programmatic areas were also identified related to: management commitment and planning; chemical safety management programs; aging facilities that continue to operate; nonoperating facilities awaiting deactivation; and resource allocations. To address the facility-specific and site-specific vulnerabilities, responsible DOE and site-contractor line organizations have developed initial site response plans. These plans, presented as Volume 2 of this Management Response Plan, describe the actions needed to mitigate or eliminate the facility- and site-specific vulnerabilities identified by the CSV Working Group field verification teams. Initial site response plans are described for: Brookhaven National Lab., Hanford Site, Idaho National Engineering Lab., Lawrence Livermore National Lab., Los Alamos National Lab., Oak Ridge Reservation, Rocky Flats Plant, Sandia National Laboratories, and Savannah River Site.

  2. Health and safety plan for operations performed for the Environmental Restoration Program. Task, OU 1-03 and OU 4-10 Track 2 investigations

    SciTech Connect

    Trippet, W.A. II; Reneau, M.; Morton, S.L.

    1992-04-01

    This document constitutes the generic health and safety plan for the Environmental Restoration Program (ERP). It addresses the health and safety requirements of the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA); Occupational Safety and Health Administration (OSHA) 29 CFR 1910.120 standard; and EG&G Idaho, Inc. This plan is a guide to individuals who must complete a health and safety plan for a task performed for the EPR. It contains a task specific addendum that, when completed, specifically addresses task specific health and safety issues. This health and safety plan reduces the time it takes to write a task specific health and safety plan by providing discussions of requirements, guidance on where specific information is located, and specific topics in the Addendum that must be discussed at a task level. This format encourages a complete task specific health and safety plan and a standard for all health and safety plans written for ERP.

  3. Industrial Fuel Gas Demonstration Plant Program. Task III, Demonstration plant safety, industrial hygiene, and major disaster plan (Deliverable No. 35)

    SciTech Connect

    1980-03-01

    This Health and Safety Plan has been adopted by the IFG Demonstration Plant managed by Memphis Light, Gas and Water at Memphis, Tennessee. The plan encompasses the following areas of concern: Safety Plan Administration, Industrial Health, Industrial Safety, First Aid, Fire Protection (including fire prevention and control), and Control of Safety Related Losses. The primary objective of this plan is to achieve adequate control of all potentially hazardous activities to assure the health and safety of all employees and eliminate lost work time to both the employees and the company. The second objective is to achieve compliance with all Federal, state and local laws, regulations and codes. Some thirty specific safe practice instruction items are included.

  4. River Protection Project Integrated safety management system phase II verification review plan - 7/29/99

    SciTech Connect

    SHOOP, D.S.

    1999-09-10

    The purpose of this review is to verify the implementation status of the Integrated Safety Management System (ISMS) for the River Protection Project (RPP) facilities managed by Fluor Daniel Hanford, Inc. (FDH) and operated by Lockheed Martin Hanford Company (LMHC). This review will also ascertain whether within RPP facilities and operations the work planning and execution processes are in place and functioning to effectively protect the health and safety of the workers, public, environment, and federal property over the RPP life cycle. The RPP ISMS should support the Hanford Strategic Plan (DOERL-96-92) to safely clean up and manage the site's legacy waste and deploy science and technology while incorporating the ISMS central theme to ''Do work safely'' and protect human health and the environment.

  5. HACCP and water safety plans in Icelandic water supply: preliminary evaluation of experience.

    PubMed

    Gunnarsdóttir, María J; Gissurarson, Loftur R

    2008-09-01

    Icelandic waterworks first began implementing hazard analysis and critical control points (HACCP) as a preventive approach for water safety management in 1997. Since then implementation has been ongoing and currently about 68% of the Icelandic population enjoy drinking water from waterworks with a water safety plan based on HACCP. Preliminary evaluation of the success of HACCP implementation was undertaken in association with some of the waterworks that had implemented HACCP. The evaluation revealed that compliance with drinking water quality standards improved considerably following the implementation of HACCP. In response to their findings, waterworks implemented a large number of corrective actions to improve water safety. The study revealed some limitations for some, but not all, waterworks in relation to inadequate external and internal auditing and a lack of oversight by health authorities. Future studies should entail a more comprehensive study of the experience with the use of HACCP with the purpose of developing tools to promote continuing success.

  6. Work plan, health and safety plan, and quality assurance project plan for hazardous waste removal at the CTF K-1654B underground collection tank

    SciTech Connect

    Panter, M.S.; Burman, S.N.; Landguth, D.C.; Uziel, M.S.

    1991-10-01

    The Central Training Facility (CTF), located on Bear Creek Road approximately two miles south of the K-25 Site, is utilized for training security personnel at Martin Marietta Energy Systems, Inc., Oak Ridge, Tennessee. At the request of the CTF staff, this plan has been developed for the removal of the waste contents in the facility's 500-gal septic tank and associated distribution box. The septic tank and distribution box were historically located beneath the K-1654B trailer and adjacent to the K-1654A Indoor Firing Range. Recently, however, the K-1654B trailer was removed to accommodate the objectives of this work plan as well as future construction activities planned at CTF. The purpose of this plan is to develop and assign responsibilities, establish personnel protection requirements and mandatory safety procedures, and provide for contingencies that may arise while operations are being conducted by ORNL/MAD at the CTF K-1654B underground collection tank site. This document addresses requirements of 29 CFR 1910.120, Final Rule, with respect to aspects of health and safety applicable to an underground collection tank waste removal.

  7. Work plan, health and safety plan, and quality assurance project plan for hazardous waste removal at the CTF K-1654B underground collection tank

    SciTech Connect

    Panter, M.S.; Burman, S.N.; Landguth, D.C.; Uziel, M.S.

    1991-10-01

    The Central Training Facility (CTF), located on Bear Creek Road approximately two miles south of the K-25 Site, is utilized for training security personnel at Martin Marietta Energy Systems, Inc., Oak Ridge, Tennessee. At the request of the CTF staff, this plan has been developed for the removal of the waste contents in the facility`s 500-gal septic tank and associated distribution box. The septic tank and distribution box were historically located beneath the K-1654B trailer and adjacent to the K-1654A Indoor Firing Range. Recently, however, the K-1654B trailer was removed to accommodate the objectives of this work plan as well as future construction activities planned at CTF. The purpose of this plan is to develop and assign responsibilities, establish personnel protection requirements and mandatory safety procedures, and provide for contingencies that may arise while operations are being conducted by ORNL/MAD at the CTF K-1654B underground collection tank site. This document addresses requirements of 29 CFR 1910.120, Final Rule, with respect to aspects of health and safety applicable to an underground collection tank waste removal.

  8. Safety planning in focus groups of Malawian women living with HIV: helping each other deal with violence and abuse.

    PubMed

    Mkandawire-Valhmu, Lucy; Stevens, Patricia E; Kako, Peninnah M; Dressel, Anne

    2013-11-01

    In this critical ethnography, 72 HIV-infected women in Southern Malawi participated in 12 focus groups discussing the impact of HIV and violence. Our analysis, informed by a postcolonial feminist perspective, revealed women's capacity to collectively engage in safety planning. We present our findings about women's experiences based on narratives detailing how women collectively strategized safety planning efforts to mitigate the impact of violence. This study helps to fill a gap in the literature on the intersection between HIV and violence in women's lives. Strategies discussed by the women could form a basis for safety planning interventions for women in similar circumstances.

  9. Provincial drug plan officials' views of the Canadian drug safety system.

    PubMed

    Lexchin, Joel; Wiktorowicz, Mary; Moscou, Kathy; Eggertson, Laura

    2013-06-01

    The Canadian constitution divides the responsibility for pharmaceuticals between the federal and provincial governments. While the provincial governments are responsible for establishing public formularies, the majority of the safety and efficacy information that the provinces use comes from the federal government. We interviewed drug plan officials from eight of the ten provinces and two of three territories regarding their views on the Canadian drug safety system. Here we report on the following categories: the federal drug approval system; the strengths and weaknesses of the federal system of postmarket pharmaceutical safety (i.e., pharmacosurveillance); resources available to support provincial formulary decision making; provincial roles in pharmacosurveillance; how the drug safety system could be improved; and the role of the Drug Safety and Effectiveness Network, a recently established virtual network designed to connect researchers throughout Canada who conduct postmarket drug research. Next, we place the Canadian system within an international context by comparing informational asymmetry between government institutions in the United States and the European Union and by looking at how institutions support each other's roles in sharing information and in jointly developing policy through the International Conference on Harmonization. Finally, we draw on international experiences and suggest potential solutions to the concerns that our key informants have identified. PMID:23418364

  10. Planning the Unplanned Experiment: Towards Assessing the Efficacy of Standards for Safety-Critical Software

    NASA Technical Reports Server (NTRS)

    Graydon, Patrick J.; Holloway, C. M.

    2015-01-01

    Safe use of software in safety-critical applications requires well-founded means of determining whether software is fit for such use. While software in industries such as aviation has a good safety record, little is known about whether standards for software in safety-critical applications 'work' (or even what that means). It is often (implicitly) argued that software is fit for safety-critical use because it conforms to an appropriate standard. Without knowing whether a standard works, such reliance is an experiment; without carefully collecting assessment data, that experiment is unplanned. To help plan the experiment, we organized a workshop to develop practical ideas for assessing software safety standards. In this paper, we relate and elaborate on the workshop discussion, which revealed subtle but important study design considerations and practical barriers to collecting appropriate historical data and recruiting appropriate experimental subjects. We discuss assessing standards as written and as applied, several candidate definitions for what it means for a standard to 'work,' and key assessment strategies and study techniques and the pros and cons of each. Finally, we conclude with thoughts about the kinds of research that will be required and how academia, industry, and regulators might collaborate to overcome the noted barriers.

  11. Planning the Unplanned Experiment: Assessing the Efficacy of Standards for Safety Critical Software

    NASA Technical Reports Server (NTRS)

    Graydon, Patrick J.; Holloway, C. Michael

    2015-01-01

    We need well-founded means of determining whether software is t for use in safety-critical applications. While software in industries such as aviation has an excellent safety record, the fact that software aws have contributed to deaths illustrates the need for justi ably high con dence in software. It is often argued that software is t for safety-critical use because it conforms to a standard for software in safety-critical systems. But little is known about whether such standards `work.' Reliance upon a standard without knowing whether it works is an experiment; without collecting data to assess the standard, this experiment is unplanned. This paper reports on a workshop intended to explore how standards could practicably be assessed. Planning the Unplanned Experiment: Assessing the Ecacy of Standards for Safety Critical Software (AESSCS) was held on 13 May 2014 in conjunction with the European Dependable Computing Conference (EDCC). We summarize and elaborate on the workshop's discussion of the topic, including both the presented positions and the dialogue that ensued.

  12. Site plan safety submission for sampling, monitoring, decontamination of GB agent - north plant Rocky Mountain Arsenal. Volume 1

    SciTech Connect

    Not Available

    1988-10-01

    The scope of this site plan safety submission (SPSS), includes: sampling plan to determine if GB is a contaminant in equipment and piping used in the production and demil processes; monitoring plan for personnel involved in the sampling effort; decon plan for personnel, equipment, and piping should contamination be identified. Additional sections and appendices include: historical use of bldg 1501, 1503, 1504, 1506, 1601, 1602, 1603, 1606; chemical information on GB; safety requirements; medical requirements and first aid procedures; piping drawings; rma sop's for sampling, monitoring, and decon.

  13. Site plan safety submission for sampling, monitoring and decontamination of mustard agent, South Plant, Rocky Mountain Arsenal. Volume 1

    SciTech Connect

    Not Available

    1988-10-01

    The scope of this site plan safety submission (SPSS) includes: (1) Sampling plan to determine if H is a contaminant in Equipment and piping used in the 1970's for the H DEMIL program; (2) Monitoring plan for personnel involved in the sampling effort; and (3) Decon plan for personnel, equipment, and piping should contamination be identified. Additional sections and appendices include: (1) Historical use of Bld 637 and Bld 538; (2) Chemical information on H, HD, and HT; (3) Safety requirements; (4) Medical requirements and first aid procedures; (5) Piping drawings; and (6) RMA SOP's for sampling, monitoring, and decon.

  14. Management response plan for the Chemical Safety Vulnerability Working Group report. Volume 1

    SciTech Connect

    Not Available

    1994-09-01

    The Chemical Safety Vulnerability (CSV) Working Group was established to identify adverse conditions involving hazardous chemicals at DOE facilities that might result in fires or explosions, release of hazardous chemicals to the environment, or exposure of workers or the public to chemicals. A CSV Review was conducted in 146 facilities at 29 sites. Eight generic vulnerabilities were documented related to: abandoned chemicals and chemical residuals; past chemical spills and ground releases; characterization of legacy chemicals and wastes; disposition of legacy chemicals; storage facilities and conditions; condition of facilities and support systems; unanalyzed and unaddressed hazards; and inventory control and tracking. Weaknesses in five programmatic areas were also identified related to: management commitment and planning; chemical safety management programs; aging facilities that continue to operate; nonoperating facilities awaiting deactivation; and resource allocations. Volume 1 contains a discussion of the chemical safety improvements planned or already underway at DOE sites to correct facility or site-specific vulnerabilities. The main part of the report is a discussion of each of the programmatic deficiencies; a description of the tasks to be accomplished; the specific actions to be taken; and the organizational responsibilities for implementation.

  15. Health and Safety Plan for Waste Area Grouping 6 at Oak Ridge National Laboratory, Oak Ridge, Tennessee. Environmental Restoration Program

    SciTech Connect

    Van Hoesen, S.D.; Clark, C. Jr.; Burman, S.N.; Manis, L.W.; Barre, W.L.

    1993-12-01

    The Martin Marietta Energy Systems, Inc. (Energy Systems), policy is to provide a safe and healthful workplace for all employees and subcontractors. The accomplishment of this policy requires that operations at Waste Area Grouping (WAG) 6 at the Department of Energy (DOE) Oak Ridge National Laboratory are guided by an overall plan and consistent proactive approach to safety and health (S&H) issues. The plan is written to utilize past experience and best management practices to minimize hazards to human health or the environment from events such as fires, explosions, falls, mechanical hazards, or any unplanned release of hazardous or radioactive materials to air, soil, or surface water This plan explains additional site-specific health and safety requirements such as Site Specific Hazards Evaluation Addendums (SSHEAs) to the Site Safety and Health Plan which should be used in concert with this plan and existing established procedures.

  16. The World Health Organization's water safety plan is much more than just an integrated drinking water quality management plan.

    PubMed

    Viljoen, F C

    2010-01-01

    South Africa is a country of contrasts with far ranging variations in climate, precipitation rates, cultures, demographics, housing levels, education, wealth and skills levels. These differences have an impact on water services delivery as do expectations, affordability and available resources. Although South Africa has made much progress in supplying drinking water, the same cannot be said regarding water quality throughout the country. A concerted effort is currently underway to correct this situation and as part of this drive, water safety plans (WSP) are promoted. Rand Water, the largest water services provider in South Africa, used the World Health Organization (WHO) WSP framework as a guide for the development of its own WSP which was implemented in 2003. Through the process of implementation, Rand Water found the WHO WSP to be much more than just another integrated quality system.

  17. Understanding safety and production risks in rail engineering planning and protection.

    PubMed

    Wilson, John R; Ryan, Brendan; Schock, Alex; Ferreira, Pedro; Smith, Stuart; Pitsopoulos, Julia

    2009-07-01

    Much of the published human factors work on risk is to do with safety and within this is concerned with prediction and analysis of human error and with human reliability assessment. Less has been published on human factors contributions to understanding and managing project, business, engineering and other forms of risk and still less jointly assessing risk to do with broad issues of 'safety' and broad issues of 'production' or 'performance'. This paper contains a general commentary on human factors and assessment of risk of various kinds, in the context of the aims of ergonomics and concerns about being too risk averse. The paper then describes a specific project, in rail engineering, where the notion of a human factors case has been employed to analyse engineering functions and related human factors issues. A human factors issues register for potential system disturbances has been developed, prior to a human factors risk assessment, which jointly covers safety and production (engineering delivery) concerns. The paper concludes with a commentary on the potential relevance of a resilience engineering perspective to understanding rail engineering systems risk. Design, planning and management of complex systems will increasingly have to address the issue of making trade-offs between safety and production, and ergonomics should be central to this. The paper addresses the relevant issues and does so in an under-published domain - rail systems engineering work.

  18. [Patient safety culture in hospitals: experiences in planning, organising and conducting a survey among hospital staff].

    PubMed

    van Vegten, Amanda; Pfeiffer, Yvonne; Giuliani, Francesca; Manser, Tanja

    2011-01-01

    This article presents the first hospital-wide survey on patient safety climate, involving all staff (medical and non-medical), in the German-speaking area. Its aim is to share our experiences with planning, organising and conducting this survey. The study was performed at the university hospital in Zurich and had a response rate of 46.8% (2,897 valid questionnaires). The survey instrument ("Patientensicherheitsklimainventar") was based on the Hospital Survey on Patient Safety Culture (AHRQ). Primarily it allowed for assessing the current patient safety climate as well as identifying specific areas for improvement and creating a hospital-wide awareness and acceptance for patient safety issues and interventions (e.g., the introduction of a Critical Incident Reporting System [CIRS]). We discuss the basic principles and the feedback concept guiding the organisation of the overall project. Critical to the success of this project were the guaranteed anonymity of the respondents, adequate communication through well-established channels within the organisation and the commitment of the management across all project phases.

  19. Standard review plan for reviewing safety analysis reports for dry metallic spent fuel storage casks

    SciTech Connect

    Not Available

    1988-01-01

    The Cask Standard Review Plan (CSRP) has been prepared as guidance to be used in the review of Cask Safety Analysis Reports (CSARs) for storage packages. The principal purpose of the CSRP is to assure the quality and uniformity of storage cask reviews and to present a well-defined base from which to evaluate proposed changes in the scope and requirements of reviews. The CSRP also sets forth solutions and approaches determined to be acceptable in the past by the NRC staff in dealing with a specific safety issue or safety-related design area. These solutions and approaches are presented in this form so that reviewers can take consistent and well-understood positions as the same safety issues arise in future cases. An applicant submitting a CSAR does not have to follow the solutions or approaches presented in the CSRP. However, applicants should recognize that the NRC staff has spent substantial time and effort in reviewing and developing their positions for the issues. A corresponding amount of time and effort will probably be required to review and accept new or different solutions and approaches.

  20. Risk assessment and water safety plan: case study in Beijing, China.

    PubMed

    Ye, Bixiong; Chen, Yuansheng; Li, Yonghua; Li, Hairong; Yang, Linsheng; Wang, Wuyi

    2015-06-01

    Two typical rural water utilities in Beijing, China were chosen to describe the principles and applications of water safety plans (WSP), to provide a methodological guide for the actual application and improve the quality of rural drinking water quality, and to establish an appropriate method for WSP applied in rural water supply. Hazards and hazardous events were identified and risk assessment was conducted for rural water supply systems. A total of 13 and 12 operational limits were defined for two utilities, respectively. The main risk factors that affect the water safety were identified in water sources, water processes, water disinfection systems and water utility management. The main control measures were strengthening the water source protection, monitoring the water treatment processes, establishing emergency mechanisms, improving chemical input and operating system management. WSP can be feasibly applied to the management of a rural water supply.

  1. 75 FR 35315 - Improving Public Safety Communications in the 800 MHz Band; New 800 MHz Band Plan for Puerto Rico...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-06-22

    ... public safety and other land mobile communication systems operating in the band, 69 FR 67823, November 22... Puerto Rico market compared to other markets, 72 FR 39756, July 20, 2007. Rather than specify a band plan... 800 MHz band reconfiguration in Puerto Rico as well as alternative band plans, 73 FR 40274, July...

  2. HAZWOPER work plan and site safety and health plan for the Alpha characterization project at the solid waste storage area 4 bathtubbing trench at Oak Ridge National Laboratory

    SciTech Connect

    Not Available

    1994-07-01

    This work plan/site safety and health plan is for the alpha sampling project at the Solid Waste Storage Area 4 bathtubbing trench. The work will be conducted by the Oak Ridge National Laboratory (ORNL) Environmental Sciences Division and associated ORNL environmental, safety, and health support groups. This activity will fall under the scope of 29 CFR 1910.120, Hazardous Waste Operations and Emergency Response (HAZWOPER). The purpose of this document is to establish health and safety guidelines to be followed by all personnel involved in conducting work for this project. Work will be conducted in accordance with requirements as stipulated in the ORNL HAZWOPER Program Manual and applicable ORNL; Martin Marietta Energy Systems, Inc.; and U.S. Department of Energy policies and procedures. The levels of protection and the procedures specified in this plan are based on the best information available from historical data and preliminary evaluations of the area. Therefore, these recommendations represent the minimum health and safety requirements to be observed by all personnel engaged in this project. Unforeseeable site conditions or changes in scope of work may warrant a reassessment of the stated protection levels and controls. All adjustments to the plan must have prior approval by the safety and health disciplines signing the original plan.

  3. Planning a collaborative conference to provide interdisciplinary education with a focus on patient safety in obstetrics.

    PubMed

    Doyle, Jennifer; Newhouse, Linda; Flora, Robert; Burkett, Amy

    2014-01-01

    Collaboration is an important component of evidence-based practice in modern health care. A number of publications have touted the benefits of "team training" to improve obstetric outcomes during emergent situations. In August 2011, the Ohio sections of the Association of Women's Health, Obstetric and Neonatal Nurses (AWHONN) and the American Congress of Obstetricians and Gynecologists (ACOG) held a joint conference that focused on interdisciplinary education to promote patient safety. This joint venture drew more than 120 attendees, 12 exhibitors and 17 poster displays. Evaluations were positive and attendees cited planned practice changes for themselves as well as for their respective institutions.

  4. CONTEXTUALIZED ASSESSMENT WITH BATTERED WOMEN: STRATEGIC SAFETY PLANNING TO COPE WITH MULTIPLE HARMS

    PubMed Central

    Lindhorst, Taryn; Nurius, Paula; Macy, Rebecca J.

    2007-01-01

    Given the prevalence of domestic violence and the likelihood that many victims will not receive services from specialized domestic violence providers, this article provides a framework for contextualized assessment that can be used by generalist practitioners. Drawing from stress and coping theory, the authors discuss the relevance of assessing appraisals and emotional responses within the context of environmental and individual risk and protective factors. Through an illustrative case assessment, the authors describe the contextualized assessment process and its ramifications for strategic safety planning. PMID:18167523

  5. Best management practices plan for Phase II of the Bear Creek Valley treatability study, Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

    SciTech Connect

    1997-09-01

    The Oak Ridge Y-12 Plant is currently under a Federal Agreement to define soil and groundwater contamination and develop remedies to protect human health and the environment. The western end of the site is known to have a former nitric acid disposal pit that has been remediated and capped. Remedial investigation data indicate this pit was a source of nitrate, uranium, technetium, and other metals contamination in groundwater. The downgradient receptor of this contamination includes Bear Creek and its tributaries. A feasibility study is under way to develop a remedy to prevent further contaminant migration to this receptor. To support the feasibility study, the treatability study is being completed to examine groundwater treatment at the S-3 site. This document serves as the top-level command medium for Phase II of the Bear Creek Valley (BCV) Treatability Study and, as such, will be the primary resource for management and implementation of field activities. Many of the details and standard operating procedures referred to herein can be found in other Lockheed Martin Energy Systems, Inc. (Energy Systems), documents. Several supporting documents specific to this project are also cited. These include the Sampling and Analysis Plan (SAP), the Health and Safety Plan (HASP), and the Waste Management Plan (WMP).

  6. Project health and safety plan for the Gunite and Associated Tanks at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect

    Abston, J.P.

    1997-04-01

    The Lockheed Martin Energy Systems, Inc. (Energy Systems) policy is to provide a safe and healthful workplace for all employees and subcontractors. The accomplishment of this policy requires that operations at the Gunite and Associated Tanks (GAAT) in the North and South Tank Farms (NTF and STF) at the Department of Energy (DOE) Oak Ridge National Laboratory are guided by an overall plan and consistent proactive approach to health and safety (H and S) issues. The policy and procedures in this plan apply to all GAAT operations in the NTF and STF. The provisions of this plan are to be carried out whenever activities identifies s part of the GAAT are initiated that could be a threat to human health or the environment. This plan implements a policy and establishes criteria for the development of procedures for day-to-day operations to prevent or minimize any adverse impact to the environment and personnel safety and health and to meet standards that define acceptable management of hazardous and radioactive materials and wastes. The plan is written to utilize past experience and best management practices in order to minimize hazards to human health or the environment from events such as fires, explosions, falls, mechanical hazards, or any unplanned release of hazardous or radioactive materials to the air. This plan explains additional task-specific health and safety requirements such as the Site Safety and health Addendum and Activity Hazard Analysis, which should be used in concert with this plan and existing established procedures.

  7. Implementation of School Districts' Food Safety Plans and Perceptions of Support for Food Safety and Training in Child Nutrition Programs in One USDA Region

    ERIC Educational Resources Information Center

    Dawso Van Druff, Cynthia A.

    2012-01-01

    School foodservice directors (FSDs) and school business officials (SBOs) in public school districts with enrollments between 2,500 and 25,000 in the USDA Mid-Atlantic geographic region provided responses to a paper-and-pencil survey. The FSDs assessed the level of implementation of a mandated school food safety plan in their districts and…

  8. Site health and safety plan/work plan for further characterization of waste drums at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect

    Abston, J.P.; Burman, S.N.; Jones, D.L.

    1995-10-01

    The health and safety plan/work plan describes a strategy for characterizing the contents of 172 liquid waste and 33 solid waste drums. It also addresses the control measures that will be taken to (1) prevent or minimize any adverse impact on the environment or personnel safety and health and (2) meet standards that define acceptable management of hazardous and radioactive materials and wastes. When writing this document, the authors considered past experiences, recommendations, and best management practices to minimize possible hazards to human health or the environment from events such as fires, explosions, falls, mechanical hazards, or unplanned releases of hazardous or radioactive materials to air, soil, or surface water.

  9. 78 FR 23855 - Improving Public Safety Communications in the 800 MHz Band; New 800 MHz Band Plan for U.S.-Mexico...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-04-23

    ... for the National Public Safety Planning Advisory Committee (NPCPAC) Regions bordering Mexico, 77 FR...: This document establishes a reconfigured 800 MHz band plan for the National Public Safety Planning Advisory Committee Regions bordering Mexico. This action is necessary to meet the Commission's goals...

  10. Guidance for implementing an environmental, safety, and health-assurance program. Volume 15. A model plan for line organization environmental, safety, and health-assurance programs

    SciTech Connect

    Ellingson, A.C.; Trauth, C.A. Jr.

    1982-01-01

    This is 1 of 15 documents designed to illustrate how an Environmental, Safety and Health (ES and H) Assurance Program may be implemented. The generic definition of ES and H Assurance Programs is given in a companion document entitled An Environmental, Safety and Health Assurance Program Standard. This particular document presents a model operational-level ES and H Assurance Program that may be used as a guide by an operational-level organization in developing its own plan. The model presented here reflects the guidance given in the total series of 15 documents.

  11. 76 FR 38267 - The Federal Motor Carrier Safety Administration's 2011-2016 Strategic Plan: Raising the Safety Bar

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-06-29

    ... overall CMV transportation life-cycle. The CMV transportation life-cycle concept encompasses the whole CMV... are part of the CMV transportation life-cycle need to be aware of their impact on CMV safety and take... transportation life-cycle. Recognize that, while safety is FMCSA's highest priority, the Agency must also...

  12. Exploration of Tunnel Alignment using Geophysical Methods to Increase Safety for Planning and Minimizing Risk

    NASA Astrophysics Data System (ADS)

    Lehmann, Bodo; Orlowsky, Dirk; Misiek, Rüdiger

    2010-02-01

    Engineering geophysics provides valuable and continuous information for the planning and execution of tunnel construction projects. For geotechnical purposes special high-resolution geophysical methods have been developed during the last decades. The importance of applying geophysical methods in addition to usually used geological and geotechnical exploration techniques is increasing. The main goal is to achieve an accurate and continuous model of the subsurface in a relative short period of operation time. The routine application of engineering geophysical methods will increase in the coming years. Due to the high acceptance of engineering geophysics at construction sites, much wider application of geophysical investigations is expected. The combination of different methods—geophysics, geology, and geotechnics as well as the so-called joint interpretation techniques—will be of essential importance. Engineering geophysics will play an important role during the three phases: geological investigation, tunnel planning, and execution of tunnel construction. If hazards are well known in advance of a tunnel project the safety of workers will essentially be increased and geological risks will be minimized by means of successful and interdisciplinary cooperation.

  13. Quadrivalent HPV vaccine safety review and safety monitoring plans for nine-valent HPV vaccine in the United States.

    PubMed

    Gee, Julianne; Weinbaum, Cindy; Sukumaran, Lakshmi; Markowitz, Lauri E

    2016-06-01

    Quadrivalent human papillomavirus (4vHPV) vaccine was licensed for use in the United States in 2006 and through 2015 was the predominate HPV vaccine used. With the exception of syncope, a known preventable adverse event after any injected vaccination, both pre-licensure and post-licensure 4vHPV safety data have been reassuring with no confirmed safety signals identified. Nine-valent HPV vaccine (9vHPV) was licensed in 2014. This review includes post-licensure 4vHPV safety findings published to date that have informed the US vaccination program; these data will inform US safety monitoring and evaluation for 9vHPV. PMID:27029786

  14. [ILO plan of action (2010-2016) on occupational safety and health and new list of occupational diseases].

    PubMed

    Denisov, É I; Mazitova, N N; Shemetova, M V; Chelishcheva, M Iu; Chesalin, P V

    2011-01-01

    ILO plan of action (2010-2016) to achieve widespread ratification and effective implementation of the occupational safety and health instruments (Convention No. 155, its 2002 Protocol and Convention No. 187) is discussed. ILO documents on recording and notification as well as new list of occupational diseases (revised 2010) are considered.

  15. [ILO plan of action (2010-2016) on occupational safety and health and new list of occupational diseases].

    PubMed

    Denisov, É I; Mazitova, N N; Shemetova, M V; Chelishcheva, M Iu; Chesalin, P V

    2011-01-01

    ILO plan of action (2010-2016) to achieve widespread ratification and effective implementation of the occupational safety and health instruments (Convention No. 155, its 2002 Protocol and Convention No. 187) is discussed. ILO documents on recording and notification as well as new list of occupational diseases (revised 2010) are considered. PMID:21614798

  16. Organizational Development and Strategic Planning for the Millennium: A Blueprint toward Effective School Discipline, Safety, and Crisis Prevention.

    ERIC Educational Resources Information Center

    Knoff, Howard M.

    2000-01-01

    Presents a blueprint from Project ACHIEVE toward effective school discipline, safety, and crisis prevention that provides an example of how school psychologists can expand their role using organizational and strategic planning principles and activities as well as to alert school psychologists as to a field-tested process that addresses the…

  17. Comprehensive work plan and health and safety plan for the 7500 Area Contamination Site sampling at Oak Ridge National Laboratory, Oak Ridge, Tennessee. Environmental Restoration Program

    SciTech Connect

    Burman, S.N.; Landguth, D.C.; Uziel, M.S.; Hatmaker, T.L.; Tiner, P.F.

    1992-05-01

    As part of the Environmental Restoration Program sponsored by the US Department of Energy`s Office of Environmental Restoration and Waste Management, this plan has been developed for the environmental sampling efforts at the 7500 Area Contamination Site, Oak Ridge National Laboratory (ORNL), Oak Ridge, Tennessee. This plan was developed by the Measurement Applications and Development Group (MAD) of the Health and Safety Research Division of ORNL and will be implemented by ORNL/MAD. Major components of the plan include (1) a quality assurance project plan that describes the scope and objectives of ORNL/MAD activities at the 7500 Area Contamination Site, assigns responsibilities, and provides emergency information for contingencies that may arise during field operations; (2) sampling and analysis sections; (3) a site-specific health and safety section that describes general site hazards, hazards associated with specific tasks, personnel protection requirements, and mandatory safety procedures; (4) procedures and requirements for equipment decontamination and responsibilities for generated wastes, waste management, and contamination control; and (5) a discussion of form completion and reporting required to document activities at the 7500 Area Contamination Site.

  18. Comprehensive work plan and health and safety plan for the 7500 Area Contamination Site sampling at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect

    Burman, S.N.; Landguth, D.C.; Uziel, M.S.; Hatmaker, T.L.; Tiner, P.F.

    1992-05-01

    As part of the Environmental Restoration Program sponsored by the US Department of Energy's Office of Environmental Restoration and Waste Management, this plan has been developed for the environmental sampling efforts at the 7500 Area Contamination Site, Oak Ridge National Laboratory (ORNL), Oak Ridge, Tennessee. This plan was developed by the Measurement Applications and Development Group (MAD) of the Health and Safety Research Division of ORNL and will be implemented by ORNL/MAD. Major components of the plan include (1) a quality assurance project plan that describes the scope and objectives of ORNL/MAD activities at the 7500 Area Contamination Site, assigns responsibilities, and provides emergency information for contingencies that may arise during field operations; (2) sampling and analysis sections; (3) a site-specific health and safety section that describes general site hazards, hazards associated with specific tasks, personnel protection requirements, and mandatory safety procedures; (4) procedures and requirements for equipment decontamination and responsibilities for generated wastes, waste management, and contamination control; and (5) a discussion of form completion and reporting required to document activities at the 7500 Area Contamination Site.

  19. Safety.

    ERIC Educational Resources Information Center

    Education in Science, 1996

    1996-01-01

    Discusses safety issues in science, including: allergic reactions to peanuts used in experiments; explosions in lead/acid batteries; and inspection of pressure vessels, such as pressure cookers or model steam engines. (MKR)

  20. Environmental health and safety independent investigation of the in situ vitrification melt expulsion at the Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect

    1996-07-01

    At about 6:12 pm, EDT on April 21, 1996, steam and molten material were expelled from Pit 1 in situ vitrification (ISV) project at the Oak Ridge National Laboratory (ORNL). At the request of the director of the Environmental Restoration (ER) Division, Department of Energy Oak Ridge Operations (DOE ORO), an independent investigation team was established on April 26, 1996. This team was tasked to determine the facts related to the ORNL Pit 1 melt expulsion event (MEE) in the areas of environment safety and health concerns such as the adequacy of the ISV safety systems; operational control restrictions; emergency response planning/execution; and readiness review, and report the investigation team findings within 45 days from the date of incident. These requirements were stated in the letter of appointment presented in Appendix A of this report. This investigation did not address the physical causes of the MEE. A separate investigation was conducted by ISV project personnel to determine the causes of the melt expulsion and the extent of the effects of this phenomenon. In response to this event, occurrence report ORO-LMES-X10ENVRES-1996-0006 (Appendix B) was filed. The investigation team did not address the occurrence reporting or event notification process. The project personnel (project team) examined the physical evidence at Pit 1 ISV site (e.g., the ejected melt material and the ISV hood), reviewed documents such as the site- specific health and safety plan (HASP), and interviewed personnel involved in the event and/or the project. A listing of the personnel interviewed and evidence reviewed is provided in Appendix C.

  1. Development of a strategic plan for food security and safety in the Inuvialuit Settlement Region, Canada

    PubMed Central

    Fillion, Myriam; Laird, Brian; Douglas, Vasiliki; Van Pelt, Linda; Archie, Diane; Chan, Hing Man

    2014-01-01

    Background Current social and environmental changes in the Arctic challenge the health and well-being of its residents. Developing evidence-informed adaptive measures in response to these changes is a priority for communities, governments and researchers. Objectives To develop strategic planning to promote food security and food safety in the Inuvialuit Settlement Region (ISR), Northwest Territories (NWT), Canada. Design A qualitative study using group discussions during a workshop. Methods A regional workshop gathered Inuit organizations and community representatives, university-based researchers from the Inuit Health Survey (IHS) and NWT governmental organizations. Discussions were structured around the findings from the IHS. For each key area, programs and activities were identified and prioritized by group discussion and voting. Results The working group developed a vision for future research and intervention, which is to empower communities to promote health, well-being and environmental sustainability in the ISR. The group elaborated missions for the region that address the following issues: (a) capacity building within communities; (b) promotion of the use of traditional foods to address food security; (c) research to better understand the linkages between diseases and contaminants in traditional foods, market foods and lifestyle choices; (d) and promotion of affordable housing. Five programs to address each key area were developed as follows: harvest support and traditional food sharing; education and promotion; governance and policy; research; and housing. Concrete activities were identified to guide future research and intervention projects. Conclusions The results of the planning workshop provide a blueprint for future research and intervention projects. PMID:25147772

  2. Waste management plan for phase II of the Bear Creek Valley Treatability study Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

    SciTech Connect

    1997-09-01

    This Waste Management Plan (WMP) for the Bear Creek Valley Treatability Study addresses waste management requirements for the Oak Ridge Y-12 Plant. The study is intended to produce treatment performance data required to design a treatment system for contaminated groundwater. The treatability study will consist of an evaluation of various treatment media including continuous column tests, with up to six columns being employed to evaluate the performance of different media in the treatment of groundwater; an evaluation of the dentrifying capacity and metal uptake capacity of a wetland system; and the long-term dentrifying capacity and metal uptake capacity of algal mats. Additionally, the treatability study involves installation of a trench and incline well to evaluate and assess hydraulic impacts of pumping groundwater. The Sampling and Analysis Plan (SAP) covers the project description, technical objectives, procedures, and planned work activities in greater detail. The Health and Safety Plan (HASP) addresses the health and safety concerns and requirements for the proposed sampling activities. This WMP identifies the types and estimates the volumes of various wastes that may be generated during the proposed treatability studies. The approach to managing waste outlined in this WMP emphasizes the following points: (1) management of the waste generated in a manner that is protective of human health and the environment; (2) minimization of waste generation, thereby reducing unnecessary costs and usage of limited permitted storage and disposal capacities; and (3) compliance with federal, state, and site requirements. Prior sampling at the site has detected organic, radioactive, and metals contamination in groundwater and surface water. Proposed field operations are not expected to result in worker exposures greater than applicable exposure or action limits.

  3. Site specific health and safety plan, 233-S decontamination and decommissioning

    SciTech Connect

    J. E. Fasso

    1997-12-31

    The deactivated 233-S Plutonium Concentration Facility, located in the 200 Area at the Hanford Site, is the subject of this Health and Safety Plan.The 233-S Facility operated from January 1952 until July 1967 at which time the building entered the U.S. Department of Energy`s Surplus Facility Management Program as a retired facility. The facility has since undergone severe degradation due to exposure to extreme weather conditions. Additionally, the weather caused existing cracks in concrete structures of the building to lengthen, thereby increasing the potential for failed confinement of the radioactive material in the building. Differential settlement has also occurred causing portions of the facility to separate from the main building structure, increasing the potential for release of radioactive material to the environment. An expedited response is proposed to remove this threat and ensure protection of human health and the environment. On this premise it is intended that the 233-S Facility removal action be performed as a Comprehensive Environmental Response, Compensation, and Liability Act of 1980 Time-Critical Project being conducted under the Pilot Hanford Environmental Restoration (ER) Initiative

  4. Spent Nuclear Fuel (SNF) project Integrated Safety Management System phase I and II Verification Review Plan

    SciTech Connect

    CARTER, R.P.

    1999-11-19

    The U.S. Department of Energy (DOE) commits to accomplishing its mission safely. To ensure this objective is met, DOE issued DOE P 450.4, Safety Management System Policy, and incorporated safety management into the DOE Acquisition Regulations ([DEAR] 48 CFR 970.5204-2 and 90.5204-78). Integrated Safety Management (ISM) requires contractors to integrate safety into management and work practices at all levels so that missions are achieved while protecting the public, the worker, and the environment. The contractor is required to describe the Integrated Safety Management System (ISMS) to be used to implement the safety performance objective.

  5. Safety Planning for Military (SAFE MIL): rationale, design, and safety considerations of a randomized controlled trial to reduce suicide risk among psychiatric inpatients.

    PubMed

    Ghahramanlou-Holloway, Marjan; Brown, Gregory K; Currier, Glenn W; Brenner, Lisa; Knox, Kerry L; Grammer, Geoffrey; Carreno-Ponce, Jaime T; Stanley, Barbara

    2014-09-01

    Mental health related hospitalizations and suicide are both significant public health problems within the United States Department of Defense (DoD). To date, few evidence-based suicide prevention programs have been developed for delivery to military personnel and family members admitted for psychiatric inpatient care due to suicidal self-directed violence. This paper describes the rationale and detailed methodology for a study called Safety Planning for Military (SAFE MIL) which involves a randomized controlled trial (RCT) at the largest military treatment facility in the United States. The purpose of this study is to test the efficacy of a brief, readily accessible, and personalized treatment called the Safety Planning Intervention (Stanley and Brown, 2012). Primary outcomes, measured by blinded assessors at one and six months following psychiatric discharge, include suicide ideation, suicide-related coping, and attitudes toward help seeking. Additionally, given the study's focus on a highly vulnerable patient population, a description of safety considerations for human subjects' participation is provided. Based on this research team's experience, the implementation of an infrastructure in support of RCT research within DoD settings and the processing of regulatory approvals for a clinical trial with high risk suicidal patients are expected to take up to 18-24 months. Recommendations for expediting the advancement of clinical trials research within the DoD are provided in order to maximize cost efficacy and minimize the research to practice gap.

  6. Program plan for evaluation of the Ferrocyanide Waste Tank safety issue at the Hanford Site

    SciTech Connect

    Borsheim, G.L.; Meacham, J.E.; Cash, R.J.; Dukelow, G.T.

    1994-03-01

    This document describes the background, priorities, strategy and logic, and task descriptions for the Ferrocyanide Waste Tank Safety Program. The Ferrocyanide Safety Program was established in 1990 to provide resolution of a major safety issue identified for 24 high-level radioactive waste tanks at the Hanford Site.

  7. Health and safety plan for the Molten Salt Reactor Experiment remediation project at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect

    Burman, S.N.; Uziel, M.S.

    1995-12-01

    The Lockheed Martin Energy Systems, Inc., (Energy Systems) policy is to provide a safe and healthful workplace for all employees and subcontractors. The accomplishment of the policy requires that operations at the Molten Salt Reactor Experiment (MSRE) facility at the Department of Energy (DOE) Oak Ridge National Laboratory (ORNL) are guided by an overall plan and consistent proactive approach to safety and health (S and H) issues. The policy and procedures in this plan apply to all MSRE operations. The provisions of this plan are to be carried out whenever activities are initiated at the MSRE that could be a threat to human health or the environment. This plan implements a policy and establishes criteria for the development of procedures for day-to-day operations to prevent or minimize any adverse impact to the environment and personnel safety and health and to meet standards that define acceptable management of hazardous and radioactive materials and wastes. The plan is written to utilize past experience and the best management practices to minimize hazards to human health or the environment from events such as fires, explosions, falls, mechanical hazards, or any unplanned release of hazardous or radioactive materials to the air.

  8. Health and Safety Plan for Operations Performed for the Environmental Restoration Program: Task, Characterization of Potential Waste Sources at Auxiliary Reactor Area-1 Operable Unit 5--07 site ARA-02

    SciTech Connect

    Pickett, S.L.; Morton, S.L.

    1992-06-01

    This document constitutes the generic health and safety plan for the Environmental Restoration Program (ERP). It addresses the health and safety requirements of the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA); Occupational Safety and Health Administration (OSHA) 29 CFR 1910.120 standard; and EG&G Idaho, Inc. This plan is a guide to individuals who must complete a health and safety plan for a task performed for the ERP. It contains a task specific addendum that, when completed, specifically addresses task specific health and safety issues. This health and safety plan reduces the time it takes to write a task specific health and safety plan by providing discussions of requirements, guidance on where specific information is located, and specific topics in the Addendum that must be discussed at a task level. This format encourages a complete task specific health and safety plan and a standard for all health and safety plans written for ERP.

  9. Health and Safety Plan for Operations Performed for the Environmental Restoration Program: Task, Characterization of Potential Waste Sources at Auxiliary Reactor Area-1 Operable Unit 5--07 site ARA-02

    SciTech Connect

    Pickett, S.L.; Morton, S.L.

    1992-06-01

    This document constitutes the generic health and safety plan for the Environmental Restoration Program (ERP). It addresses the health and safety requirements of the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA); Occupational Safety and Health Administration (OSHA) 29 CFR 1910.120 standard; and EG G Idaho, Inc. This plan is a guide to individuals who must complete a health and safety plan for a task performed for the ERP. It contains a task specific addendum that, when completed, specifically addresses task specific health and safety issues. This health and safety plan reduces the time it takes to write a task specific health and safety plan by providing discussions of requirements, guidance on where specific information is located, and specific topics in the Addendum that must be discussed at a task level. This format encourages a complete task specific health and safety plan and a standard for all health and safety plans written for ERP.

  10. Test plan and report for Space Shuttle launch environment testing of Bergen cable technology safety cable

    NASA Technical Reports Server (NTRS)

    Ralph, John

    1992-01-01

    Bergen Cable Technology (BCT) has introduced a new product they refer to as 'safety cable'. This product is intended as a replacement for lockwire when installed per Aerospace Standard (AS) 4536 (included in Appendix D of this document). Installation of safety cable is reportedly faster and more uniform than lockwire. NASA/GSFC proposes to use this safety cable in Shuttle Small Payloads Project (SSPP) applications on upcoming Shuttle missions. To assure that BCT safety cable will provide positive locking of fasteners equivalent to lockwire, the SSPP will conduct vibration and pull tests of the safety cable.

  11. 49 CFR 236.1015 - PTC Safety Plan content requirements and PTC System Certification.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... § 236.1005; (19) An emergency and planned maintenance temporary rerouting plan indicating how operations... supplied from other business systems needed to execute the braking algorithm, survey data needed...

  12. WAG 2 remedial investigation and site investigation site-specific work plan/health and safety checklist for the soil and sediment task. Environmental Restoration Program

    SciTech Connect

    Holt, V.L.; Burgoa, B.B.

    1993-12-01

    This document is a site-specific work plan/health and safety checklist (WP/HSC) for a task of the Waste Area Grouping 2 Remedial Investigation and Site Investigation (WAG 2 RI&SI). Title 29 CFR Part 1910.120 requires that a health and safety program plan that includes site- and task-specific information be completed to ensure conformance with health- and safety-related requirements. To meet this requirement, the health and safety program plan for each WAG 2 RI&SI field task must include (1) the general health and safety program plan for all WAG 2 RI&SI field activities and (2) a WP/HSC for that particular field task. These two components, along with all applicable referenced procedures, must be kept together at the work site and distributed to field personnel as required. The general health and safety program plan is the Health and Safety Plan for the Remedial Investigation and Site Investigation of Waste Area Grouping 2 at the Oak Ridge National Laboratory, Oak Ridge, Tennessee (ORNL/ER-169). The WP/HSCs are being issued as supplements to ORNL/ER-169.

  13. 78 FR 69745 - Safety and Security Plans for Class 3 Hazardous Materials Transported by Rail

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-11-20

    ... rail transportation of Class 3 hazardous materials, including FRA's Emergency Order No. 28 (78 FR 48218 (EO 28)); the agencies' Joint Safety Advisory published on August 7, 2013 (78 FR 48224) (First Joint... of hazardous materials by rail (78 FR 42998); the referral of safety issues related to EO 28 and...

  14. 29 CFR Appendix A to Subpart P to... - Model Fire Safety Plan (Non-Mandatory)

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Subpart P to Part 1915 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) OCCUPATIONAL SAFETY AND HEALTH STANDARDS FOR SHIPYARD EMPLOYMENT... of Contents I. Purpose. II. Work site fire hazards and how to properly control them. III....

  15. 29 CFR Appendix A to Subpart P of... - Model Fire Safety Plan (Non-Mandatory)

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Subpart P of Part 1915 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) OCCUPATIONAL SAFETY AND HEALTH STANDARDS FOR SHIPYARD EMPLOYMENT... of Contents I. Purpose. II. Work site fire hazards and how to properly control them. III....

  16. Health and Safety Work Plan for Sampling Colloids in Waste Area Grouping 5 at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect

    Marsh, J.D.; McCarthy, J.F.

    1994-01-01

    This Work Plan/Site Safety and Health Plan (SSHP) and the attached work plan are for the performance of the colloid project at WAG 5. The work will be conducted by the Oak Ridge National Laboratory (ORNL) Environmental Sciences Division (ESD) and associated ORNL environmental, safety, and health support groups. The purpose of this document is to establish health and safety guidelines to be followed by all personnel involved in conducting work for this project. The levels of protection and the procedures specified in this plan are based on the best information available from historical data and preliminary evaluations of the area. Therefore, these recommendations represent the minimum health and safety requirements to be observed by all personnel engaged in this project.

  17. An examination of the potential added value of water safety plans to the United States national drinking water legislation.

    PubMed

    Baum, Rachel; Amjad, Urooj; Luh, Jeanne; Bartram, Jamie

    2015-11-01

    National and sub-national governments develop and enforce regulations to ensure the delivery of safe drinking water in the United States (US) and countries worldwide. However, periodic contamination events, waterborne endemic illness and outbreaks of waterborne disease still occur, illustrating that delivery of safe drinking water is not guaranteed. In this study, we examined the potential added value of a preventive risk management approach, specifically, water safety plans (WSPs), in the US in order to improve drinking water quality. We undertook a comparative analysis between US drinking water regulations and WSP steps to analyze the similarities and differences between them, and identify how WSPs might complement drinking water regulations in the US. Findings show that US drinking water regulations and WSP steps were aligned in the areas of describing the water supply system and defining monitoring and controls. However, gaps exist between US drinking water regulations and WSPs in the areas of team procedures and training, internal risk assessment and prioritization, and management procedures and plans. The study contributes to understanding both required and voluntary drinking water management practices in the US and how implementing water safety plans could benefit water systems to improve drinking water quality and human health.

  18. An examination of the potential added value of water safety plans to the United States national drinking water legislation.

    PubMed

    Baum, Rachel; Amjad, Urooj; Luh, Jeanne; Bartram, Jamie

    2015-11-01

    National and sub-national governments develop and enforce regulations to ensure the delivery of safe drinking water in the United States (US) and countries worldwide. However, periodic contamination events, waterborne endemic illness and outbreaks of waterborne disease still occur, illustrating that delivery of safe drinking water is not guaranteed. In this study, we examined the potential added value of a preventive risk management approach, specifically, water safety plans (WSPs), in the US in order to improve drinking water quality. We undertook a comparative analysis between US drinking water regulations and WSP steps to analyze the similarities and differences between them, and identify how WSPs might complement drinking water regulations in the US. Findings show that US drinking water regulations and WSP steps were aligned in the areas of describing the water supply system and defining monitoring and controls. However, gaps exist between US drinking water regulations and WSPs in the areas of team procedures and training, internal risk assessment and prioritization, and management procedures and plans. The study contributes to understanding both required and voluntary drinking water management practices in the US and how implementing water safety plans could benefit water systems to improve drinking water quality and human health. PMID:25618192

  19. Systems Engineering Management Plan for Tank Farm Restoration and Safety Operations Project W-314

    SciTech Connect

    MCGREW, D.L.

    2000-04-19

    The Systems Engineering Management Plan for Project W-314 has been prepared within the guidelines of HNF-SD-WM-SEMP-002, TWRS Systems Engineering Management Plan. The activities within this SEMP have been tailored, in accordance with the TWRS SEMP and DOE Order 430.1, Life Cycle Asset Management, to meet the needs of the project.

  20. Research Needs in Fire Safety for the Human Exploration and Utilization of Space: Proceedings and Research Plan

    NASA Technical Reports Server (NTRS)

    Ruff, Gary A.

    2003-01-01

    The purpose of the workshop documented in this publication was to bring together personnel responsible for the design and operations of the International Space Station (ISS) and the fire protection research community to review the current knowledge in fire safety relative to spacecraft. From this review, research needs were identified that were then used to formulate a research plan with specific objectives. In this document, I have attempted to capture the very informative and lively discussions that occurred in the plenary sessions and the working groups. I hope that it will be useful to readers and serve as a significant step in assuring fire protection for the crews of current and future spacecraft.

  1. 49 CFR 236.1015 - PTC Safety Plan content requirements and PTC System Certification.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... additional requirements apply to: (1) Non-vital overlay. A PTC system proposed as an overlay on the existing... greater than the level of safety for the previous PTC systems. (2) Vital overlay. A PTC system proposed on a newly constructed track or as an overlay on the existing method of operation and built...

  2. Safety Barrier Guidelines for Home Pools [and] How To Plan for the Unexpected.

    ERIC Educational Resources Information Center

    Consumer Product Safety Commission, Washington, DC.

    Each year, hundreds of young children die and thousands come close to death due to submersion in residential swimming pools. The United States Consumer Products Safety Commission studied data on drownings and child behavior, as well as information on pool and pool barrier construction, and concluded that the best way to reduce child drownings in…

  3. 49 CFR 236.1015 - PTC Safety Plan content requirements and PTC System Certification.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... method of operation and not built in accordance with the safety assurance principles set forth in... a newly constructed track or as an overlay on the existing method of operation and built in... signal or train control system, or otherwise to replace or materially modify the existing method...

  4. Hazard and risk assessment for indirect potable reuse schemes: An approach for use in developing Water Safety Plans.

    PubMed

    Dominguez-Chicas, Angelina; Scrimshaw, Mark D

    2010-12-01

    This paper describes research undertaken to develop an approach for facilitating an initial hazard assessment and risk characterisation for a proposed indirect potable reuse scheme, as part of the water safety plan recommended by the World Health Organization. The process involved a description and evaluation of the catchment, which was the sewerage system supplying the sewage treatment works that would provide the effluent to supply the pilot scale indirect potable reuse water treatment plant. Hazards, sources and barriers throughout the proposed system were identified and evaluated. An initial assessment of the possible hazards, highlighted chemical hazards as predominating, and assessment of risks, using a heat map as output, categorised most hazards as medium or high risk. However, this outcome has been influenced by a precautionary approach which assigned a high likelihood to the occurrence of hazards where no data was available on their occurrence in the system. As more data becomes available, and the waster safety plan develops, it is anticipated that the risk heat map will become more specific. Additionally, high quality targets, to drinking water standards, have been set, although water from the potable reuse plant will be discharged to receiving waters where it will undergo natural attenuation prior to further treatment to potable standards before distribution. The assessment has demonstrated the usefulness of the approach where data is initially limited, in generating a heat map allowing for prioritisation of hazards to a practical level.

  5. Documentary analysis of risk-assessment and safety-planning policies and tools in a mental health context.

    PubMed

    Higgins, Agnes; Doyle, Louise; Morrissey, Jean; Downes, Carmel; Gill, Ailish; Bailey, Sive

    2016-08-01

    Despite the articulated need for policies and processes to guide risk assessment and safety planning, limited guidance exists on the processes or procedures to be used to develop such policies, and there is no body of research that examines the quality or content of the risk-management policies developed. The aim of the present study was to analyse the policies of risk and safety management used to guide mental health nursing practice in Ireland. A documentary analysis was performed on 123 documents received from 22 of the 23 directors of nursing contacted. Findings from the analysis revealed a wide variation in how risk, risk assessment, and risk management were defined. Emphasis within the risk documentation submitted was on risk related to self and others, with minimal attention paid to other types of risks. In addition, there was limited evidence of recovery-focused approaches to positive risk taking that involved service users and their families within the risk-related documentation. Many of the risk-assessment tools had not been validated, and lacked consistency or guidance in relation to how they were to be used or applied. The tick-box approach and absence of space for commentary within documentation have the potential to impact severely on the quality of information collected and documented, and subsequent clinical decision-making. Managers, and those tasked with ensuring safety and quality, need to ensure that policies and processes are, where possible, informed by best evidence and are in line with national mental health policy on recovery.

  6. Development and implementation of water safety plans for small water supplies in Bangladesh: benefits and lessons learned.

    PubMed

    Mahmud, S G; Shamsuddin, Sk Abu Jafar; Ahmed, M Feroze; Davison, Annette; Deere, Dan; Howard, Guy

    2007-12-01

    Water safety plans (WSPs) are promoted by the WHO as the most effective means of securing drinking water safety. To date most experience with WSPs has been within utility supplies, primarily in developed countries. There has been little documented experience of applying WSPs to small community-managed systems, particularly in developing countries. This paper presents a case study from Bangladesh describing how WSPs can be developed and implemented for small systems. Model WSPs were developed through consultation with key water sector practitioners in the country. Simplified tools were developed to translate the formal WSPs into a format that was meaningful and accessible for communities to use. A series of pilot projects were implemented by Non-Governmental Organisations (NGOs) across the country covering all major water supplies. The results show that WSPs can be developed and implemented for small community managed water supplies and improve the sanitary condition and water quality of water sources. Hygiene behaviour improved and household water quality showed a significant reduction in contamination. Chlorination was found to be important for some technologies, thus increasing the costs of water supply and raising important problems with respect to transfer to the communities. Simple tools for community monitoring were found to be effective in supporting better water safety management. PMID:17878569

  7. Lunar mission safety and rescue: Escape/rescue analysis and plan

    NASA Technical Reports Server (NTRS)

    1971-01-01

    The results are presented of the technical analysis of escape/rescue/survival situations, crew survival techniques, alternate escape/rescue approaches and vehicles, and the advantages and disadvantages of each for advanced lunar exploration. Candidate escape/rescue guidelines are proposed and elements of a rescue plan developed. The areas of discussions include the following: lunar arrival/departure operations, lunar orbiter operations, lunar surface operations, lunar surface base escape/rescue analysis, lander tug location operations, portable airlock, emergency pressure suit, and the effects of no orbiting lunar station, no lunar surface base, and no foreign lunar orbit/surface operations on the escape/rescue plan.

  8. Light Water Reactor Sustainability Program: Reactor Safety Technologies Pathway Technical Program Plan

    SciTech Connect

    Corradini, M. L.

    2015-06-01

    In the aftermath of the March 2011 multi-unit accident at the Fukushima Daiichi nuclear power plant (Fukushima), the nuclear community has been reassessing certain safety assumptions about nuclear reactor plant design, operations and emergency actions, particularly with respect to extreme events that might occur and that are beyond each plant’s current design basis. Because of our significant domestic investment in nuclear reactor technology (99 operating reactors in the fleet of commercial LWRs with five under construction), the United States has been a major leader internationally in these activities. The U.S. nuclear industry is voluntarily pursuing a number of additional safety initiatives. The NRC continues to evaluate and, where deemed appropriate, establish new requirements for ensuring adequate protection of public health and safety in the occurrence of low probability events at nuclear plants; (e.g., mitigation strategies for beyond design basis events initiated by external events like seismic or flooding initiators). The DOE has also played a major role in the U.S. response to the Fukushima accident. Initially, DOE worked with the Japanese and the international community to help develop a more complete understanding of the Fukushima accident progression and its consequences, and to respond to various safety concerns emerging from uncertainties about the nature of and the effects from the accident. DOE R&D activities are focused on providing scientific and technical insights, data, analyses methods that ultimately support industry efforts to enhance safety. These activities are expected to further enhance the safety performance of currently operating U.S. nuclear power plants as well as better characterize the safety performance of future U.S. plants. In pursuing this area of R&D, DOE recognizes that the commercial nuclear industry is ultimately responsible for the safe operation of licensed nuclear facilities. As such, industry is considered the primary

  9. 12 CFR 308.303 - Filing of safety and soundness compliance plan.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... operating under, a capital restoration plan submitted pursuant to section 38 of the FDI Act (12 U.S.C. 1831o), a cease-and-desist order entered into pursuant to section 8 of the FDI Act, a formal or informal..., by a bank that is not well capitalized for purposes of section 38 of the FDI Act. For purposes...

  10. Office of River Protection Integrated Safety Management System Phase 1 Verification Corrective Action Plan

    SciTech Connect

    CLARK, D.L.

    1999-08-09

    The purpose of this Corrective Action Plan is to demonstrate the OW planned and/or completed actions to implement ISMS as well as prepare for the RPP ISMS Phase II Verification scheduled for August, 1999. This Plan collates implied or explicit ORP actions identified in several key ISMS documents and aligns those actions and responsibilities perceived necessary to appropriately disposition all ISM Phase II preparation activities specific to the ORP. The objective will be to complete or disposition the corrective actions prior to the commencement of the ISMS Phase II Verification. Improvement products/tasks not slated for completion prior to the RPP Phase II verification will be incorporated as corrective actions into the Strategic System Execution Plan (SSEP) Gap Analysis. Many of the business and management systems that were reviewed in the ISMS Phase I verification are being modified to support the ORP transition and are being assessed through the SSEP. The actions and processes identified in the SSEP will support the development of the ORP and continued ISMS implementation as committed to be complete by end of FY-2000.

  11. High-Poverty Urban High School Students' Plans for Higher Education: Weaving Their Own Safety Nets

    ERIC Educational Resources Information Center

    Cilesiz, Sebnem; Drotos, Stephanie M.

    2016-01-01

    This qualitative study investigates high-poverty urban high school students' views of and plans regarding higher education, using Bourdieu's theory of reproduction in education as theoretical framework. Interview data from 76 students from six high-poverty urban schools in a metropolitan area in the Midwestern United States were analyzed using…

  12. Development of a consortium for water security and safety: Planning for an early warning system

    USGS Publications Warehouse

    Clark, R.M.; Adam, N.R.; Atluri, V.; Halem, M.; Vowinkel, E.F.; ,

    2004-01-01

    The events of September 11, 2001 have raised concerns over the safety and security of the Nation's critical infrastructure including water and waste water systems. In June 2002, the U.S. EPA's Region II Office (New York City), in response to concerns over water security, in collaboration with Rutgers University agreed to establish a Regional Drinking Water Security and Safety Consortium (RDWSSC). Members of the consortium include: Rutgers University's Center for Information Management, Integration and Connectivity (CIMIC), American Water (AW), the Passaic Valley Water Commission (PVWC), the North Jersey District Water Supply Commission (NJDWSC), the N.J. Department of Environmental Protection, the U.S. Geological Survey (USGS), and the U.S. Environmental Protection Agencies, Region II Office. In December of 2002 the consortium members signed a memorandum of understanding (MOU) to pursue activities to enhance regional water security. Development of an early warning system for source and distributed water was identified as being of primary importance by the consortium. In this context, an early warning system (EWS) is an integrated system of monitoring stations located at strategic points in a water utilities source waters or in its distribution system, designed to warn against contaminants that might threaten the health and welfare of drinking water consumers. This paper will discuss the consortium's progress in achieving these important objectives.

  13. Identification, assessment, and control of hazards in water supply: experiences from Water Safety Plan implementations in Germany.

    PubMed

    Mälzer, H-J; Staben, N; Hein, A; Merkel, W

    2010-01-01

    According to the recommendations of the World Health Organization (WHO) for Water Safety Plans (WSP), a Technical Risk Management was developed, which considers standard demands in drinking water treatment in Germany. It was already implemented at several drinking water treatment plants of different size and treatment processes in Germany. Hazards affecting water quality, continuity, and the reliability of supply from catchment to treatment and distribution could be identified by a systematic approach, and suitable control measures were defined. Experiences are presented by detailed examples covering methods, practical consequences, and further outcomes. The method and the benefits for the water suppliers are discussed and an outlook on the future role of WSPs in German water supply is given.

  14. Diabetes Health Information Technology Innovation to Improve Quality of Life for Health Plan Members in Urban Safety Net

    PubMed Central

    Ratanawongsa, Neda; Handley, Margaret A.; Sarkar, Urmimala; Quan, Judy; Pfeifer, Kelly; Soria, Catalina; Schillinger, Dean

    2014-01-01

    Safety net systems need innovative diabetes self-management programs for linguistically diverse patients. A low-income government-sponsored managed care plan implemented a 27-week automated telephone self-management support (ATSM) / health coaching intervention for English, Spanish-, and Cantonese-speaking members from four publicly-funded clinics in a practice-based research network. Compared to waitlist, immediate intervention participants had greater 6-month improvements in overall diabetes self-care behaviors (standardized effect size [ES] 0.29, p<0.01) and SF-12 physical scores (ES 0.25, p=0.03); changes in patient-centered processes of care and cardiometabolic outcomes did not differ. ATSM is a strategy for improving patient-reported self-management and may also improve some outcomes. PMID:24594561

  15. Environmental, Safety, and Health Plan for the remedial investigation of the liquid low-level waste tanks at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect

    DeFalco, S.; Kaiser, L. L.; May, L. E.

    1991-09-01

    The Environmental, Safety, and Health (ES H) Plan presents the concepts and methodologies to be used during the Oak Ridge National Laboratory (ORNL) RI/FS project to protect the health and safety of employees, the public, and the environment. The ES H Plan acts as a management extension for ORNL and Energy Systems to direct and control implementation of the project ES H program. This report describes the program philosophy, requirements, quality assurance measures, and methods for applying the ES H program to individual task remedial investigations, project facilities, and other major tasks assigned to the project.

  16. Environmental, Safety, and Health Plan for the remedial investigation of the liquid low-level waste tanks at Oak Ridge National Laboratory, Oak Ridge, Tennessee. Environmental Restoration Program

    SciTech Connect

    Not Available

    1991-09-01

    The Environmental, Safety, and Health (ES&H) Plan presents the concepts and methodologies to be used during the Oak Ridge National Laboratory (ORNL) RI/FS project to protect the health and safety of employees, the public, and the environment. The ES&H Plan acts as a management extension for ORNL and Energy Systems to direct and control implementation of the project ES&H program. This report describes the program philosophy, requirements, quality assurance measures, and methods for applying the ES&H program to individual task remedial investigations, project facilities, and other major tasks assigned to the project.

  17. Space capsule recovery—Evaluation of risk factors, safety plans and procedures and design of experiments for systems qualification

    NASA Astrophysics Data System (ADS)

    Narasaiah, N.; Varaprasad, R.; Seshagiri Rao, V.; Krishnamurty, V.; Sanyal, M. K.

    2009-11-01

    The Indian Space capsule (SRE-1) launched aboard PSLV-C7 rocket, was recovered successfully in the Bay of Bengal on January 22, 2007 after its orbital sojourn of 12 days. Apart from serving as a platform for micro-gravity experiments, SRE-1 demonstrated ISRO's capability in the field of orbital reentry and recovery technologies. Satish Dhawan Space Centre (SDSC SHAR), the Spaceport of India was given the prime responsibility of assessment of mission risk, formulation and execution of safety plans and procedures, design and conduct of trials for validating the mission-critical sub-systems as well as the physical recovery of the capsule. To achieve these objectives, a number of drop tests were designed and conducted by SDSC SHAR involving real time computer network, ground-based tracking and telemetry stations, communication systems, safety and material handling systems, target identification and recovery systems. Dissemination of relevant information and coordination with multiple external organizations such as Indian Coast Guard, Indian Air Force and Indian Navy is an important aspect of these experiments. This paper delineates the methodologies designed and implemented at SDSC SHAR for validating those critical systems whose functionality finally culminated in the success of the mission, enabling India to join the elite group of nations with reentry module recovery capability.

  18. Faster-than-real-time robot simulation for plan development and robot safety

    SciTech Connect

    Crane, C.D. III; Dalton, R.; Ogles, J.; Tulenko, J.S.; Zhou, X. )

    1990-06-01

    The University of Florida, in cooperation with the Universities of Texas, Tennessee, and Michigan and Oak Ridge National Laboratory (ORNL), is developing an advanced robotic system for the US Department of Energy under the University Program for Robotics for Advanced Reactors. As part of this program, the University of Florida has been pursuing the development of a faster-than-real-time robotic simulation program for planning and control of mobile robotic operations to ensure the efficient and safe operation of mobile robots in nuclear power plants and other hazardous environments.

  19. Documentary analysis of risk-assessment and safety-planning policies and tools in a mental health context.

    PubMed

    Higgins, Agnes; Doyle, Louise; Morrissey, Jean; Downes, Carmel; Gill, Ailish; Bailey, Sive

    2016-08-01

    Despite the articulated need for policies and processes to guide risk assessment and safety planning, limited guidance exists on the processes or procedures to be used to develop such policies, and there is no body of research that examines the quality or content of the risk-management policies developed. The aim of the present study was to analyse the policies of risk and safety management used to guide mental health nursing practice in Ireland. A documentary analysis was performed on 123 documents received from 22 of the 23 directors of nursing contacted. Findings from the analysis revealed a wide variation in how risk, risk assessment, and risk management were defined. Emphasis within the risk documentation submitted was on risk related to self and others, with minimal attention paid to other types of risks. In addition, there was limited evidence of recovery-focused approaches to positive risk taking that involved service users and their families within the risk-related documentation. Many of the risk-assessment tools had not been validated, and lacked consistency or guidance in relation to how they were to be used or applied. The tick-box approach and absence of space for commentary within documentation have the potential to impact severely on the quality of information collected and documented, and subsequent clinical decision-making. Managers, and those tasked with ensuring safety and quality, need to ensure that policies and processes are, where possible, informed by best evidence and are in line with national mental health policy on recovery. PMID:26889653

  20. Planning and Building Qualifiable Embedded Systems: Safety and Risk Properties Assessment for a Large and Complex System with Embedded Subsystems

    NASA Astrophysics Data System (ADS)

    Silva, N.; Lopes, R.; Barbosa, R.

    2012-01-01

    Systems based on embedded components and applications are today used in all markets. They are planned and developed by all types of institutions with different types of background experience, multidisciplinary teams and all types of capability and maturity levels. Organisational/engineering maturity has an impact on all aspects of the engineering of large and complex systems. An embedded system is a specific computer system designed to perform one or more dedicated functions, usually with real-time constraints. It is generally integrated as part of a more complex device typically composed of specific hardware such as sensors and actuators. This article presents an experimented technique to evaluate the organisation, processes, system and software engineering practices, methods, tools and the planned/produced artefacts themselves, leading towards certification/qualification. The safety and risk assessment of such core and complex systems is explained, described on a step-by- step manner, while presenting the main results and conclusions of the application of the technique to a real case study.

  1. Implication of spot position error on plan quality and patient safety in pencil-beam-scanning proton therapy

    SciTech Connect

    Yu, Juan; Beltran, Chris J. Herman, Michael G.

    2014-08-15

    Purpose: To quantitatively and systematically assess dosimetric effects induced by spot positioning error as a function of spot spacing (SS) on intensity-modulated proton therapy (IMPT) plan quality and to facilitate evaluation of safety tolerance limits on spot position. Methods: Spot position errors (PE) ranging from 1 to 2 mm were simulated. Simple plans were created on a water phantom, and IMPT plans were calculated on two pediatric patients with a brain tumor of 28 and 3 cc, respectively, using a commercial planning system. For the phantom, a uniform dose was delivered to targets located at different depths from 10 to 20 cm with various field sizes from 2{sup 2} to 15{sup 2} cm{sup 2}. Two nominal spot sizes, 4.0 and 6.6 mm of 1 σ in water at isocenter, were used for treatment planning. The SS ranged from 0.5 σ to 1.5 σ, which is 2–6 mm for the small spot size and 3.3–9.9 mm for the large spot size. Various perturbation scenarios of a single spot error and systematic and random multiple spot errors were studied. To quantify the dosimetric effects, percent dose error (PDE) depth profiles and the value of percent dose error at the maximum dose difference (PDE [ΔDmax]) were used for evaluation. Results: A pair of hot and cold spots was created per spot shift. PDE[ΔDmax] is found to be a complex function of PE, SS, spot size, depth, and global spot distribution that can be well defined in simple models. For volumetric targets, the PDE [ΔDmax] is not noticeably affected by the change of field size or target volume within the studied ranges. In general, reducing SS decreased the dose error. For the facility studied, given a single spot error with a PE of 1.2 mm and for both spot sizes, a SS of 1σ resulted in a 2% maximum dose error; a SS larger than 1.25 σ substantially increased the dose error and its sensitivity to PE. A similar trend was observed in multiple spot errors (both systematic and random errors). Systematic PE can lead to noticeable hot

  2. Objective 1: Extend Life, Improve Performance, and Maintain Safety of the Current Fleet Implementation Plan

    SciTech Connect

    Robert Youngblood

    2011-02-01

    Nuclear power has reliably and economically contributed almost 20% of electrical generation in the United States over the past two decades. It remains the single largest contributor (more than 70%) of non-greenhouse-gas-emitting electric power generation in the United States. By the year 2030, domestic demand for electrical energy is expected to grow to levels of 16 to 36% higher than 2007 levels. At the same time, most currently operating nuclear power plants will begin reaching the end of their 60 year operating licenses. Figure E 1 shows projected nuclear energy contribution to the domestic generating capacity. If current operating nuclear power plants do not operate beyond 60 years, the total fraction of generated electrical energy from nuclear power will begin to decline—even with the expected addition of new nuclear generating capacity. The oldest commercial plants in the United States reached their 40th anniversary in 2009. The U.S. Department of Energy Office of Nuclear Energy’s Research and Development (R&D) Roadmap has organized its activities in accordance with four objectives that ensure nuclear energy remains a compelling and viable energy option for the United States. The objectives are as follows: (1) develop technologies and other solutions that can improve the reliability, sustain the safety, and extend the life of the current reactors; (2) develop improvements in the affordability of new reactors to enable nuclear energy to help meet the Administration’s energy security and climate change goals; (3) develop sustainable nuclear fuel cycles; and (4) understand and minimize risks of nuclear proliferation and terrorism. The Light Water Reactor Sustainability (LWRS) Program is the primary programmatic activity that addresses Objective 1. This document describes how Objective 1 and the LWRS Program will be implemented. The existing U.S. nuclear fleet has a remarkable safety and performance record and today accounts for 70% of the low greenhouse

  3. Objective 1: Extend Life, Improve Performance, and Maintain Safety of the Current Fleet Implementation Plan

    SciTech Connect

    Robert Youngblood

    2011-01-01

    Nuclear power has reliably and economically contributed almost 20% of electrical generation in the United States over the past two decades. It remains the single largest contributor (more than 70%) of non-greenhouse-gas-emitting electric power generation in the United States. By the year 2030, domestic demand for electrical energy is expected to grow to levels of 16 to 36% higher than 2007 levels. At the same time, most currently operating nuclear power plants will begin reaching the end of their 60 year operating licenses. Figure E 1 shows projected nuclear energy contribution to the domestic generating capacity. If current operating nuclear power plants do not operate beyond 60 years, the total fraction of generated electrical energy from nuclear power will begin to decline—even with the expected addition of new nuclear generating capacity. The oldest commercial plants in the United States reached their 40th anniversary in 2009. The U.S. Department of Energy Office of Nuclear Energy’s Research and Development (R&D) Roadmap has organized its activities in accordance with four objectives that ensure nuclear energy remains a compelling and viable energy option for the United States. The objectives are as follows: (1) develop technologies and other solutions that can improve the reliability, sustain the safety, and extend the life of the current reactors; (2) develop improvements in the affordability of new reactors to enable nuclear energy to help meet the Administration’s energy security and climate change goals; (3) develop sustainable nuclear fuel cycles; and (4) understand and minimize risks of nuclear proliferation and terrorism. The Light Water Reactor Sustainability (LWRS) Program is the primary programmatic activity that addresses Objective 1. This document describes how Objective 1 and the LWRS Program will be implemented. The existing U.S. nuclear fleet has a remarkable safety and performance record and today accounts for 70% of the low greenhouse

  4. Urban temperatures in Hong Kong: thermal environmental safety and implications for city planning.

    PubMed

    Chiu, Tor; Wong, Pauline; Lam, Stephanie; Burd, Andrew; Nichol, Janet

    2009-01-01

    Cutaneous thermal injury caused by direct contact with objects heated solely by sun exposure is rare. We undertook to investigate factors that may influence the temperature of sun-exposed objects at the ground level. Two clinical cases of burns caused by contact with sun-exposed objects are described. Surface temperatures on a citywide scale were determined from satellite thermal images. Ground level surface temperatures of a variety of objects were measured using an infrared thermometer. The satellite thermal image demonstrated local surface temperature differences (of more than 10.6 degrees C variation) and the temperature at the places of study (8.5-9.5 degrees C above background). Infrared thermometer readings demonstrated that the surface temperature of a sun-exposed black car could be as high as 75.0 degrees C (range, 71-78 degrees C) compared with 44.6 degrees C (42.2-47.3 degrees C) for a white car, and shading significantly reduced the surface temperatures of exposed objects (10.4-48.1%). The risk of injury is related to the effects of city planning on urban temperatures, of material color, composition, and shade on the ground level temperatures, and to the rise in global temperatures because of greenhouse-induced warming. The combined effect means that in a modern subtropical city such as Hong Kong, a substantial percentage of the urban area may have summertime surface temperatures that are high enough to constitute a health hazard. We recommend that this potential cause of harm to health be taken into account during urban planning.

  5. A model plan for the uninsured: delivering quality and affordability in a limited benefit managed care safety net program in Flint, Michigan.

    PubMed

    Creech, Constance J; Kornblau, Barbara; Strugar-Fritsch, Donna

    2012-02-01

    This paper presents the background and multiyear outcome data for a limited benefit safety-net care program in Michigan. It is a possible solution for policymakers and hospital/clinic administrators to consider when evaluating plans to provide primary care for the 30 million uninsured Americans who will be affected by the Affordable Care Act.

  6. Environmental, Safety, and Health Plan for the remedial investigation/feasibility study at Oak Ridge National Laboratory, Oak Ridge, Tennessee. Revision 1, Environmental Restoration Program

    SciTech Connect

    Davis, C. M.; El-Messidi, O. E.; Cowser, D. K.; Kannard, J. R.; Carvin, R. T.; Will, III, A. S.; Clark, Jr., C.; Garland, S. B.

    1993-05-01

    This Environmental, Safety, and Health (ES&H) Plan presents the concepts and methodologies to be followed during the remedial investigation/feasibility study (RI/FS) for Oak Ridge National Laboratory (ORNL) to protect the health and safety of employees, the public, and the environment. This ES&H Plan acts as a management extension for ORNL and Martin Marietta Energy Systems, Inc. (Energy Systems) to direct and control implementation of the project ES&H program. The subsections that follow describe the program philosophy, requirements, quality assurance measures, and methods for applying the ES&H program to individual waste area grouping (WAG) remedial investigations. Hazardous work permits (HWPs) will be used to provide task-specific health and safety requirements.

  7. Methods of Assessing the Risks Associated with Lack of Water Supplies, Water Safety Plan for National Conditions

    NASA Astrophysics Data System (ADS)

    Rybka, Sławomir

    2012-06-01

    Article shows the desire to obtain risk-control options, and bringing it to a tolerable level. Subjects were ways of managing and dealing with risk. Methods of dealing with aspects of the protection of industrial buildings and high-risk critical infrastructure vulnerability analysis methodology to the loss of integrity. Also a set method to deal with aspects of the protection of industrial buildings and high-risk critical infrastructure that is the analysis of susceptibility to loss of integrity. The article also presents the basic principles of water safety plan based on national and foreign research publications. In the next part of article WSP methodology was concluded, outlining the actions which use significantly reduces the risk of threats that could lead to supply of contaminated tap water or total interruption of its supply. In further considerations the most important steps in creating WSP were presented. In the final section the principle of modular computer system operation that is used for network management for urban water supply in Rzeszow was presented.

  8. Environmental health and safety plan for the Molten Salt Reactor Experiment Remediation Project at Oak Ridge National Laboratory, Oak Ridge, Tennessee

    SciTech Connect

    Burman, S.N.; Tiner, P.F.; Gosslee, R.C.

    1998-01-01

    The Lockheed Martin Energy Systems, Inc. (Energy Systems) policy is to provide a safe and healthful workplace for all employees and subcontractors. The accomplishment of this policy requires that operations at the Molten Salt Reactor Experiment (MSRE) facility at the Department of Energy (DOE) Oak Ridge National Laboratory (ORNL) are guided by an overall plan and consistent proactive approach to environmental protection and safety and health (S and H) issues. The policy and procedures in this plan apply to all MSRE operations. The provisions of this plan are to be carried out whenever activities are initiated at the MSRE that could be a threat to human health or the environment. This plan implements a policy and establishes criteria for the development of procedures for day-to-day operations to prevent or minimize any adverse impact to the environment and personnel safety and health and to meet standards that define acceptable management of hazardous and radioactive materials and wastes. The plan is written to utilize past experience and the best management practices to minimize hazards to human health or the environment from events such as fires, explosions, falls, mechanical hazards, or any unplanned release of hazardous or radioactive materials to the air.

  9. Light Water Reactor Sustainability Program Risk-Informed Safety Margins Characterization (RISMC) PathwayTechnical Program Plan

    SciTech Connect

    Curtis Smith; Cristian Rabiti; Richard Martineau

    2012-11-01

    Safety is central to the design, licensing, operation, and economics of Nuclear Power Plants (NPPs). As the current Light Water Reactor (LWR) NPPs age beyond 60 years, there are possibilities for increased frequency of Systems, Structures, and Components (SSCs) degradations or failures that initiate safety-significant events, reduce existing accident mitigation capabilities, or create new failure modes. Plant designers commonly “over-design” portions of NPPs and provide robustness in the form of redundant and diverse engineered safety features to ensure that, even in the case of well-beyond design basis scenarios, public health and safety will be protected with a very high degree of assurance. This form of defense-in-depth is a reasoned response to uncertainties and is often referred to generically as “safety margin.” Historically, specific safety margin provisions have been formulated, primarily based on “engineering judgment.”

  10. Measuring the impact of an interprofessional multimedia learning resource on Japanese nurses and nursing students using the Theory of Planned Behavior Medication Safety Questionnaire.

    PubMed

    Omura, Mieko; Levett-Jones, Tracy; Stone, Teresa Elizabeth; Maguire, Jane; Lapkin, Samuel

    2015-12-01

    Interprofessional communication and teamwork are essential for medication safety; however, limited educational opportunities for health professionals and students to develop these skills exist in Japan. This study evaluated the impact of an interprofessional multimedia learning resource on registered nurses' and nursing students' intention to practice in a manner promoting medication safety. Using a quasi-experimental design, Japanese registered nurses and nursing students (n = 203) were allocated to an experimental (n = 109) or control group (n = 94). Behavioral intentions of medication safety and the predictor variables of attitudes, perceived behavioral control, and subjective norms were measured using a Japanese version of the Theory of Planned Behavior Medication Safety Questionnaire. Registered nurses in the experimental group demonstrated a greater intention to collaborate and practice in a manner that enhanced medication safety, evidenced by higher scores than the control group on all predictor variables. The results demonstrate the potential for interprofessional multimedia learning resources to positively impact the behaviors of Japanese registered nurses in relation to safe medication practices. Further research in other contexts and with other cohorts is warranted. PMID:26138636

  11. Measuring the impact of an interprofessional multimedia learning resource on Japanese nurses and nursing students using the Theory of Planned Behavior Medication Safety Questionnaire.

    PubMed

    Omura, Mieko; Levett-Jones, Tracy; Stone, Teresa Elizabeth; Maguire, Jane; Lapkin, Samuel

    2015-12-01

    Interprofessional communication and teamwork are essential for medication safety; however, limited educational opportunities for health professionals and students to develop these skills exist in Japan. This study evaluated the impact of an interprofessional multimedia learning resource on registered nurses' and nursing students' intention to practice in a manner promoting medication safety. Using a quasi-experimental design, Japanese registered nurses and nursing students (n = 203) were allocated to an experimental (n = 109) or control group (n = 94). Behavioral intentions of medication safety and the predictor variables of attitudes, perceived behavioral control, and subjective norms were measured using a Japanese version of the Theory of Planned Behavior Medication Safety Questionnaire. Registered nurses in the experimental group demonstrated a greater intention to collaborate and practice in a manner that enhanced medication safety, evidenced by higher scores than the control group on all predictor variables. The results demonstrate the potential for interprofessional multimedia learning resources to positively impact the behaviors of Japanese registered nurses in relation to safe medication practices. Further research in other contexts and with other cohorts is warranted.

  12. Health and safety plan: Soil vapor-extraction treatability investigation, Site S within Operable Unit D, McClellan Air Force Base. Draft final report

    SciTech Connect

    Not Available

    1991-07-01

    The health and safety program for personnel working at McClellan Air Force Base (McAFB), California, consists of a base site safety plan (SSP) and task specific amendments. The base SSP contains general information that applies to all or most areas of the site. The base SSP contains; the project description, personnel responsibilities, site hazards, personal protective equipment (PPE), air monitoring guidelines, site control, decontamination procedures, and an emergency response plan. Predominant functions at McAFB have been to manage, maintain, and repair aircrafts, missiles, space vehicles, electronics, and communication equipment. These operations have required the use of toxic and hazardous materials. Some of the hazardous materials that have been used or generated on the base include: industrial solvents and caustic cleaners, electroplating waste, heavy metals, oils contaminated with polychlorinated biphenyls, contaminated jet fuels, low-level radioactive wastes, unused chemicals, oils and lubricants. Characterization recovery and remediation of areas affected by waste disposal practices are ongoing. Contaminated drill cuttings and purge water will be generated during field activities. Purge water will be disposed of at the industrial waste water treatment plant (IWTP) or ground water treatment plant. Drill cuttings and contaminated soils will be handled in accordance with the McAFB Soils Management Plan.

  13. Nuclear Powerplant Safety: Operations.

    ERIC Educational Resources Information Center

    Department of Energy, Washington, DC. Nuclear Energy Office.

    Powerplant systems and procedures that ensure the day-to-day health and safety of people in and around the plant is referred to as operational safety. This safety is the result of careful planning, good engineering and design, strict licensing and regulation, and environmental monitoring. Procedures that assure operational safety at nuclear…

  14. Health and safety plan for the removal action at the former YS-860 Firing Ranges, Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

    SciTech Connect

    1998-03-24

    This health and safety plan sets forth the requirements and procedures to protect the personnel involved in the removal action project at the former YS-860 Firing Ranges. This project will be conducted in a manner that ensures the protection of the safety and health of workers, the public, and the environment. The purpose of this removal action is to address lead-contaminated soil and reduce a potential risk to human health and the environment. This site is an operable unit within the Upper East Fork Poplar Creek watershed. The removal action will contribute to early source actions within the watershed. The project will accomplish this through the removal of lead-contaminated soil in the target areas of the two small arms firing ranges. The primary hazards include temperature extremes, equipment operation, noise, potential lead exposure, uneven and slippery working surfaces, and insects.

  15. [Environmental investigation of ground water contamination at Wright- Patterson Air Force Base, Ohio]. Volume 4, Health and Safety Plan (HSP); Phase 1, Task 4 Field Investigation report: Draft

    SciTech Connect

    Not Available

    1991-10-01

    This Health and Safety Plan (HSP) was developed for the Environmental Investigation of Ground-water Contamination Investigation at Wright-Patterson Air Force Base near Dayton, Ohio, based on the projected scope of work for the Phase 1, Task 4 Field Investigation. The HSP describes hazards that may be encountered during the investigation, assesses the hazards, and indicates what type of personal protective equipment is to be used for each task performed. The HSP also addresses the medical monitoring program, decontamination procedures, air monitoring, training, site control, accident prevention, and emergency response.

  16. Integration of Nevada Test Site (NTS) Work Control Programs and Incorporating Integrated Safety Management (ISM) into Activity Level Work Planning and Control

    SciTech Connect

    Mike Kinney and Kevin Breen

    2008-08-30

    This session will examine a method developed by Federal and Contractor personnel at the Nevada Site Office (NSO) to improve the planning and execution of work activities utilizing an Activity Level Work Control process in response to Defense Nuclear Facilities Safety Board (DNFSB) Recommendation 2004-1, Oversight of Complex, High-Hazard Nuclear Operations. The process was initially developed during Fiscal Year (FY) 2007, and implementation is commencing during the fourth quarter of FY 2008. This process will significantly enhance the flexibility and the appropriate rigor in the performance of work activities.

  17. An international review of the challenges associated with securing 'buy-in' for water safety plans within providers of drinking water supplies.

    PubMed

    Summerill, Corinna; Smith, Jen; Webster, James; Pollard, Simon

    2010-06-01

    Since publication of the 3rd Edition of the World Health Organisation (WHO) Drinking Water Quality guidelines, global adoption of water safety plans (WSPs) has been gathering momentum. Most guidance lists managerial commitment and 'buy-in' as critical to the success of WSP implementation; yet the detail on how to generate it is lacking. This commentary discusses aspects of managerial commitment to WSPs. We argue that the public health motivator should be clearer and a paramount objective and not lost among other, albeit legitimate, drivers such as political or regulatory pressures and financial efficiency.

  18. 49 CFR 244.13 - Subjects to be addressed in a Safety Integration Plan involving an amalgamation of operations.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... transaction: (a) Corporate culture. Each applicant shall: (1) Identify and describe differences for each safety-related area between the corporate cultures of the railroads involved in the transaction; (2... step-by-step measures, the integration of these corporate cultures and the manner in which it...

  19. 76 FR 11681 - Improving Public Safety Communications in the 800 MHz Band; New 800 MHz Band Plan for Puerto Rico...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-03-03

    ... systems operating in the band, 69 FR 67823, November 22, 2004. In a Third Report and Order and Third..., USVI incumbents in the 806-809/851-854 MHz band segment will be relocated to comparable spectrum in the... COMMISSION 47 CFR Part 90 Improving Public Safety Communications in the 800 MHz Band; New 800 MHz Band...

  20. Driver and Traffic Safety Education: A Lesson Plan for the Residents of Gracewood State School and Hospital.

    ERIC Educational Resources Information Center

    Latimer, Jonathan L.

    Outlined is a course of driver education and traffic safety taught to retarded residents of a state institution. Stressed is the importance of driver education for residents able to leave the institution. The philosophy of the program is given to emphasize individualizing instruction, instructing students who possess the potential for driving,…

  1. 75 FR 36773 - Pipeline Safety: Updating Facility Response Plans in Light of the Deepwater Horizon Oil Spill

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-06-28

    ... discharging oil into or on any navigable waters of the United States or adjoining shorelines must prepare and... substantial harm to the environment by discharging oil into or on any navigable waters of the United States or... Light of the Deepwater Horizon Oil Spill AGENCY: Pipeline and Hazardous Materials Safety...

  2. New directions in office planning: The influence of the fire properties of materials and components on fire safety

    NASA Astrophysics Data System (ADS)

    Basson, G. R.

    The fire properties of some materials and building components used in modern office buildings are described. Recommendations are made on the selection and use of materials and components to ensure a reasonable degree of passive (built-in) free-safety without detracting from the functionality and flexibility of buildings.

  3. Health and safety plan for the removal action at the former YS-860 Firing Ranges, Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

    SciTech Connect

    1998-04-28

    This health and safety plan sets forth the requirements and procedures to protect the personnel involved in the Lead Source Removal Project at the Former YS-86O Firing Ranges. This project will be conducted in a manner that ensures the protection of the safety and health of workers, the public, and the environment. The purpose of this removal action is to address lead contaminated soil and reduce a potential risk to human health and the environment. This site is an operable unit within the Upper East Fork Poplar Creek watershed. The removal action will contribute to early source actions within the watershed. The project will accomplish this through the removal of lead-contaminated soil in the target areas of the two small arms firing ranges. This plan covers the removal actions at the Former YS-86O Firing Ranges. These actions involve the excavation of lead-contaminated soils, the removal of the concrete trench and macadam (asphalt) paths, verification/confirmation sampling, grading and revegetation. The primary hazards include temperature extremes, equipment operation, noise, potential lead exposure, uneven and slippery working surfaces, and insects.

  4. Guidance for the design and management of a maintenance plan to assure safety and improve the predictability of a DOE nuclear irradiation facility. Final report

    SciTech Connect

    Booth, R.S.; Kryter, R.C.; Shepard, R.L.; Smith, O.L.; Upadhyaya, B.R.; Rowan, W.J.

    1994-10-01

    A program is recommended for planning the maintenance of DOE nuclear facilities that will help safety and enhance availability throughout a facility`s life cycle. While investigating the requirements for maintenance activities, a major difference was identified between the strategy suitable for a conventional power reactor and one for a research reactor facility: the latter should provide a high degree of predicted availability (referred to hereafter as ``predictability``) to its users, whereas the former should maximize total energy production. These differing operating goals necessitate different maintenance strategies. A strategy for scheduling research reactor facility operation and shutdown for maintenance must balance safety, reliability,and predicted availability. The approach developed here is based on three major elements: (1) a probabilistic risk analysis of the balance between assured reliability and predictability (presented in Appendix C), (2) an assessment of the safety and operational impact of maintenance activities applied to various components of the facility, and (3) a data base of historical and operational information on the performance and requirements for maintenance of various components. These factors are integrated into a set of guidelines for designing a new highly maintainable facility, for preparing flexible schedules for improved maintenance of existing facilities, and for anticipating the maintenance required to extend the life of an aging facility. Although tailored to research reactor facilities, the methodology has broader applicability and may therefore be used to improved the maintenance of power reactors, particularly in anticipation of peak load demands.

  5. Cost-effective facility disposition planning with safety and health lessons learned and good practices from the Oak Ridge Decontamination and Decommissioning Program

    SciTech Connect

    1998-05-01

    An emphasis on transition and safe disposition of DOE excess facilities has brought about significant challenges to managing worker, public, and environmental risks. The transition and disposition activities involve a diverse range of hazardous facilities that are old, poorly maintained, and contain radioactive and hazardous substances, the extent of which may be unknown. In addition, many excess facilities do not have historical facility documents such as operating records, plant and instrumentation diagrams, and incident records. The purpose of this report is to present an overview of the Oak Ridge Decontamination and Decommissioning (D and D) Program, its safety performance, and associated safety and health lessons learned and good practices. Illustrative examples of these lessons learned and good practices are also provided. The primary focus of this report is on the safety and health activities and implications associated with the planning phase of Oak Ridge facility disposition projects. Section 1.0 of this report provides the background and purpose of the report. Section 2.0 presents an overview of the facility disposition activities from which the lessons learned and good practices discussed in Section 3.0 were derived.

  6. Reach and Validity of An Objective Medication Adherence Measure among Safety Net Health Plan Members with Diabetes: A Cross-Sectional Study

    PubMed Central

    Ratanawongsa, Neda; Karter, Andrew J.; Quan, Judy; Parker, Melissa M.; Handley, Margaret; Sarkar, Urmimala; Schmittdiel, Julie A.; Schillinger, Dean

    2015-01-01

    Background With the expansion of Medicaid and low-cost health insurance plans among diverse patient populations, objective measures of medication adherence using pharmacy claims could advance clinical care and translational research for safety net care. However, safety net patients may experience fluctuating prescription drug coverage, affecting the performance of adherence measures. Objective To evaluate the performance of continuous medication gap (CMG) for diverse, low-income managed care members with diabetes. Methods We conducted this cross-sectional analysis using administrative and clinical data for 680 members eligible for a self-management support trial at a non-profit, government-sponsored managed care plan. We applied CMG methodology to cardiometabolic medication claims for English-, Cantonese-, or Spanish-speaking members with diabetes. We examined inclusiveness (the proportion with calculable CMG) and selectivity (sociodemographic and medical differences from members without CMG). To examine validity, we examined unadjusted associations of suboptimal adherence (CMG>20%) with suboptimal cardiometabolic control. Results 429 members (63%) had calculable CMG. Compared to members without CMG, members with CMG were younger; more likely employed; and had poorer glycemic control, but better blood pressure and lipid control. Suboptimal adherence occurred more frequently among members with poor cardiometabolic control than among members with optimal control (28% vs. 12%, p=0.02). Conclusions CMG demonstrated acceptable inclusiveness and validity in a diverse, low-income safety net population, comparable to its performance in studies among other insured populations. CMG may provide a useful tool to measure adherence among increasingly diverse Medicaid populations, complemented by other strategies to reach those not captured by CMG. Trial Registration NCT00683020 PMID:26233541

  7. Oxygen safety

    MedlinePlus

    COPD - oxygen safety; Chronic obstructive pulmonary disease - oxygen safety; Chronic obstructive airways disease - oxygen safety; Emphysema - oxygen safety; Heart failure - oxygen-safety; Palliative care - oxygen safety; ...

  8. Site Safety and Health Plan (Phase 3) for the treatability study for in situ vitrification at Seepage Pit 1 in Waste Area Grouping 7, Oak Ridge National Laboratory, Oak Ridge, TN

    SciTech Connect

    Spalding, B.P.; Naney, M.T.

    1995-06-01

    This plan is to be implemented for Phase III ISV operations and post operations sampling. Two previous project phases involving site characterization have been completed and required their own site specific health and safety plans. Project activities will take place at Seepage Pit 1 in Waste Area Grouping 7 at ORNL, Oak Ridge, Tennessee. Purpose of this document is to establish standard health and safety procedures for ORNL project personnel and contractor employees in performance of this work. Site activities shall be performed in accordance with Energy Systems safety and health policies and procedures, DOE orders, Occupational Safety and Health Administration Standards 29 CFR Part 1910 and 1926; applicable United States Environmental Protection Agency requirements; and consensus standards. Where the word ``shall`` is used, the provisions of this plan are mandatory. Specific requirements of regulations and orders have been incorporated into this plan in accordance with applicability. Included from 29 CFR are 1910.120 Hazardous Waste Operations and Emergency Response; 1910.146, Permit Required - Confined Space; 1910.1200, Hazard Communication; DOE Orders requirements of 5480.4, Environmental Protection, Safety and Health Protection Standards; 5480.11, Radiation Protection; and N5480.6, Radiological Control Manual. In addition, guidance and policy will be followed as described in the Environmental Restoration Program Health and Safety Plan. The levels of personal protection and the procedures specified in this plan are based on the best information available from reference documents and site characterization data. Therefore, these recommendations represent the minimum health and safety requirements to be observed by all personnel engaged in this project.

  9. Planning of a Community-Based Approach to Injury Control and Safety Promotion in a Rural Community.

    ERIC Educational Resources Information Center

    Loos, Colleen; Oldenburg, Brian; O'Hara, Lily

    2001-01-01

    The planning of a community-based accident prevention program in a rural Queensland (Australia) community is described. The process involved the establishment of a local steering committee, data collection, presentation of findings, determination of priorities, review of the evidence, description of target group, exploration of problem and…

  10. 75 FR 35363 - Improving Public Safety Communications in the 800 MHz Band; New 800 MHz Band Plan for Puerto Rico...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-06-22

    ... Filing of Documents in Rulemaking Proceedings, 63 FR 24121 (1998). Electronic Filers: Comments may be..., 69 FR 67823, November 22, 2004. In a Second Memorandum Opinion and Order, adopted in May 2007, the... markets, 72 FR 39756, July 20, 2007. Rather than specify a band plan for Puerto Rico, the...

  11. Hand Safety

    MedlinePlus

    ... en gatillo See More... Hand Anatomy Hand Safety Fireworks Safety Lawnmower Safety Snowblower safety Pumpkin Carving Gardening ... en gatillo See More... Hand Anatomy Hand Safety Fireworks Safety Lawnmower Safety Snowblower safety Pumpkin Carving Gardening ...

  12. Hand Safety

    MedlinePlus

    ... Fireworks Safety Lawnmower Safety Snowblower safety Pumpkin Carving Gardening Safety Turkey Carving Removing a Ring Español Artritis ... Fireworks Safety Lawnmower Safety Snowblower safety Pumpkin Carving Gardening Safety Turkey Carving Removing a Ring Español Artritis ...

  13. Serving Up Safety.

    ERIC Educational Resources Information Center

    Fitzgerald, Patricia L.

    2002-01-01

    Describes what principals can do to protect children from food-related illness in school: Forming of food-safe school teams, developing food-safety procedures, including food safety in crises-management plans, educating staff on plans and procedures, encouraging hand washing, making sure the cafeteria works properly, and encouraging the hiring of…

  14. Environmental, safety, and health plan for the remedial investigation of Waste Area Grouping 10, Operable Unit 3, at Oak Ridge National Laboratory, Oak Ridge, Tennessee. Environmental Restoration Program

    SciTech Connect

    Not Available

    1993-10-01

    This document outlines the environmental, safety, and health (ES&H) approach to be followed for the remedial investigation of Waste Area Grouping (WAG) 10 at Oak at Ridge National Laboratory. This ES&H Plan addresses hazards associated with upcoming Operable Unit 3 field work activities and provides the program elements required to maintain minimal personnel exposures and to reduce the potential for environmental impacts during field operations. The hazards evaluation for WAG 10 is presented in Sect. 3. This section includes the potential radiological, chemical, and physical hazards that may be encountered. Previous sampling results suggest that the primary contaminants of concern will be radiological (cobalt-60, europium-154, americium-241, strontium-90, plutonium-238, plutonium-239, cesium-134, cesium-137, and curium-244). External and internal exposures to radioactive materials will be minimized through engineering controls (e.g., ventilation, containment, isolation) and administrative controls (e.g., procedures, training, postings, protective clothing).

  15. Test plan :

    SciTech Connect

    Dwyer, Stephen F.

    2013-05-01

    This test plan is a document that provides a systematic approach to the planned testing of rooftop structures to determine their actual load carrying capacity. This document identifies typical tests to be performed, the responsible parties for testing, the general feature of the tests, the testing approach, test deliverables, testing schedule, monitoring requirements, and environmental and safety compliance.

  16. Advanced Planning.

    ERIC Educational Resources Information Center

    Lupinacci, Jeffrey A.

    2000-01-01

    Explains the importance of developing a comprehensive security plan prior to purchasing more equipment and resources to bolster school safety. Decision making following the plan's development is addressed including equipment choices, ID cards, access control, exit alarms, and video monitors. (GR)

  17. Nuclear Energy Advanced Modeling and Simulation Waste Integrated Performance and Safety Codes (NEAMS Waste IPSC) verification and validation plan. version 1.

    SciTech Connect

    Bartlett, Roscoe Ainsworth; Arguello, Jose Guadalupe, Jr.; Urbina, Angel; Bouchard, Julie F.; Edwards, Harold Carter; Freeze, Geoffrey A.; Knupp, Patrick Michael; Wang, Yifeng; Schultz, Peter Andrew; Howard, Robert; McCornack, Marjorie Turner

    2011-01-01

    The objective of the U.S. Department of Energy Office of Nuclear Energy Advanced Modeling and Simulation Waste Integrated Performance and Safety Codes (NEAMS Waste IPSC) is to provide an integrated suite of computational modeling and simulation (M&S) capabilities to quantitatively assess the long-term performance of waste forms in the engineered and geologic environments of a radioactive-waste storage facility or disposal repository. To meet this objective, NEAMS Waste IPSC M&S capabilities will be applied to challenging spatial domains, temporal domains, multiphysics couplings, and multiscale couplings. A strategic verification and validation (V&V) goal is to establish evidence-based metrics for the level of confidence in M&S codes and capabilities. Because it is economically impractical to apply the maximum V&V rigor to each and every M&S capability, M&S capabilities will be ranked for their impact on the performance assessments of various components of the repository systems. Those M&S capabilities with greater impact will require a greater level of confidence and a correspondingly greater investment in V&V. This report includes five major components: (1) a background summary of the NEAMS Waste IPSC to emphasize M&S challenges; (2) the conceptual foundation for verification, validation, and confidence assessment of NEAMS Waste IPSC M&S capabilities; (3) specifications for the planned verification, validation, and confidence-assessment practices; (4) specifications for the planned evidence information management system; and (5) a path forward for the incremental implementation of this V&V plan.

  18. Aviation Safety Issues Database

    NASA Technical Reports Server (NTRS)

    Morello, Samuel A.; Ricks, Wendell R.

    2009-01-01

    The aviation safety issues database was instrumental in the refinement and substantiation of the National Aviation Safety Strategic Plan (NASSP). The issues database is a comprehensive set of issues from an extremely broad base of aviation functions, personnel, and vehicle categories, both nationally and internationally. Several aviation safety stakeholders such as the Commercial Aviation Safety Team (CAST) have already used the database. This broader interest was the genesis to making the database publically accessible and writing this report.

  19. Experimental based experiences with the introduction of a water safety plan for a multi-located university clinic and its efficacy according to WHO recommendations

    PubMed Central

    Dyck, Alexander; Exner, Martin; Kramer, Axel

    2007-01-01

    Background Due to the high number of immunosuppressed and other predisposed patients hospitals have to control and ensure the microbiological water quality. The origin for the occurrence of pathogenic microorganisms in water pipes is the formation of biofilm. Methods For the permanent control of water safety a water safety plan (WSP) was realized as recommended by the WHO following the principle "search and destroy". The WSP is based on an established HACCP concept due to the special focus. The most important measures include the concept for sample taking depending on patient risk. 3 different categories) are distinguished: risk area1 (high infection risk), risk 2 (moderate infection risk), and risk area 3 (not increased infection risk). Additionally to the threshold value of the German law for the quality of drinking water (TrinkwV) three more limiting values were defined (warning, alert, and worst case) for immediate risk adapted reaction. Additional attention has to be focussed on lavatory sinks, which are an open bacterial reservoir. Therefore continuous disinfecting siphons were installed as part of the WSP in high risk areas. If extended technical equipment is not available, especially for immunocompromised patients the following measures are easy to realize: boiled (or sun exposed) water for nursing procedures as well alimentary use, no showering. Results Comparing data over 3 years the microbial water quality was significantly improved resulting in no new case of nosocomial Legionella pneumoniae and decrease in neonatal sepsis. Conclusion According to average situations with highly contaminated water system the management must be defined with implementation of water task force, immediate providing of special equipment, information of patients and staff and control of the water quality, an example for successful decontamination of the hospital within 24 hours is given. PMID:17355621

  20. Structured nursing communication on interdisciplinary acute care teams improves perceptions of safety, efficiency, understanding of care plan and teamwork as well as job satisfaction.

    PubMed

    Gausvik, Christian; Lautar, Ashley; Miller, Lisa; Pallerla, Harini; Schlaudecker, Jeffrey

    2015-01-01

    Efficient, accurate, and timely communication is required for quality health care and is strongly linked to health care staff job satisfaction. Developing ways to improve communication is key to increasing quality of care, and interdisciplinary care teams allow for improved communication among health care professionals. This study examines the patient- and family-centered use of structured interdisciplinary bedside rounds (SIBR) on an acute care for the elderly (ACE) unit in a 555-bed metropolitan community hospital. This mixed methods study surveyed 24 nurses, therapists, patient care assistants, and social workers to measure perceptions of teamwork, communication, understanding of the plan for the day, safety, efficiency, and job satisfaction. A similar survey was administered to a control group of 38 of the same staff categories on different units in the same hospital. The control group units utilized traditional physician-centric rounding. Significant differences were found in each category between the SIBR staff on the ACE unit and the control staff. Nurse job satisfaction is an important marker of retention and recruitment, and improved communication may be an important aspect of increasing this satisfaction. Furthermore, improved communication is key to maintaining a safe hospital environment with quality patient care. Interdisciplinary team rounds that take place at the bedside improve both nursing satisfaction and related communication markers of quality and safety, and may help to achieve higher nurse retention and safer patient care. These results point to the interconnectedness and dual benefit to both job satisfaction and patient quality of care that can come from enhancements to team communication.

  1. Seismotectonic characteristics of the Krško Basin with relation to seismic safety of existing and planned nuclear infrastructure

    NASA Astrophysics Data System (ADS)

    Bavec, Miloš; Atanackov, Jure; Jamšek Rupnik, Petra

    2015-04-01

    The Kr\\vsko Basin hosts complex infrastructure and is being investigated as a potential site for several future projects including a new NPP and a low and intermediate level radioactive waste repository. A large database of geological, geophysical and geotechnical data has been accumulated, producing increasingly detailed tectonic and seismotectonic models of the Kr\\vsko Basin. The first tectonic and seismotectonic investigation campaign was undertaken in the 1970s for the first Kr\\vsko NPP (Arsovski et al., 1973). The next study (Fajfar et al., 1994) was followed by an extensive geophysical survey in in which basin axis-trending syncline was reevaluated (Persoglia, ed., 2000). In 2004 the geological, tectonic and seismotectonic characteristics of the Kr\\vsko Basin were readdressed by performing a periodic seismic hazard assessment for the NPP (Swan et al., 2004). After which, a series of field investigations were conducted for the potential radwaste repository site evaluation (Brenčič, ed., 2006; Petkovšek, ed., 2009). In 2008-2013 a set of geological, geotechnical and seismological investigations were performed for the proposed new NPP unit (Bazargan-Sabet et al., 2010). As part of this project the seismotectonic model and the seismic source model were updated (Bavec et al., 2010a,b). Particular attention was given to the Libna fault (Bavec et al., 2013), which was also the subject of a follow up study to further evaluate the age of deformed sediments in the basin (Cline et al., 2013). A new phase of geological, geophysical and geomorphic investigations is being undertaken in the Kr\\vsko basin by the team of Rizzo Associates and Geological Survey of Slovenia to refine on the geological and seismological inputs to the planned PSHA. The Basin has experienced moderate and dispersed seismic activity. The catalogue of known earthquakes in the region (ARSO, 2011) extends back to the early 17th century. The strongest earthquake in the Kr\\vsko basin was the

  2. Safety for Older Consumers. Home Safety Checklist.

    ERIC Educational Resources Information Center

    Consumer Product Safety Commission, Washington, DC.

    A home safety checklist geared to the needs of older adults is presented in this document. The beginning of the checklist highlights potential hazards which may need to be checked in more than one area of the home, such as electric cords, smoke detectors, rugs, telephone areas, and emergency exit plans. The rest of the checklist is organized…

  3. Staying Secure for School Safety

    ERIC Educational Resources Information Center

    Youngkin, Minu

    2012-01-01

    Proper planning and preventive maintenance can increase school security and return on investment. Preventive maintenance begins with planning. Through careful planning, education institutions can determine what is working and if any equipment, hardware or software needs to be replaced or upgraded. When reviewing a school's safety and security…

  4. Essentials for starting a pediatric clinical study (4): Clinical pediatric safety planning based on preclinical toxicity studies and pediatric pharmacovigilance guidance.

    PubMed

    Sheth, Neha

    2009-01-01

    Juvenile toxicology studies in animals provide useful information to guide monitoring of potential adverse effects in children especially on growth and development. In order to continue to gain knowledge and build upon these preclinical studies, recent experience has suggested that additional approaches for monitoring of safety concerns in the pediatric population may be required. Recently, pediatric guidance has become available from the health authorities which provide pharmacovigilance concepts as they specifically relate to drugs being developed for pediatric indications. Clinical trials are typically not robust enough to detect rare or delayed safety effects as the pediatric trials are relatively short-term. Furthermore, such long term or rare effects may not be detected via standard voluntary postmarketing surveillance. Safety monitoring of children with Juvenile Inflammatory Arthritis (JIA) taking nonsteroid anti-inflammatory drug (NSAID)s will be used as an example to describe a post-marketing risk management and pharmacovigilance program that serves to better evaluate safety data from various sources. The intent of this program is to identify adverse events (AE), including events with longer latency, which may be associated with NSAID use in a pediatric population. In this presentation, the 4 major components of the program are to be addressed. Such a program may serve as a model to proactively generate and monitor safety data in order to identify AEs that may be associated with new therapeutics for a pediatric population. PMID:19571487

  5. Seismic Safety Guide

    SciTech Connect

    Eagling, D.G.

    1983-09-01

    This guide provides managers with practical guidelines for administering a comprehensive earthquake safety program. The Guide is comprehensive with respect to earthquakes in that it covers the most important aspects of natural hazards, site planning, evaluation and rehabilitation of existing buildings, design of new facilities, operational safety, emergency planning, special considerations related to shielding blocks, non-structural elements, lifelines, fire protection and emergency facilities. Management of risk and liabilities is also covered. Nuclear facilities per se are not dealt with specifically. The principles covered also apply generally to nuclear facilities but the design and construction of such structures are subject to special regulations and legal controls.

  6. 23 CFR 1335.6 - Strategic plan.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 23 Highways 1 2011-04-01 2011-04-01 false Strategic plan. 1335.6 Section 1335.6 Highways NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION STATE HIGHWAY SAFETY DATA IMPROVEMENTS § 1335.6 Strategic plan. A strategic plan shall— (a) Be a multi-year plan that identifies and...

  7. 23 CFR 1335.6 - Strategic plan.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 23 Highways 1 2010-04-01 2010-04-01 false Strategic plan. 1335.6 Section 1335.6 Highways NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION STATE HIGHWAY SAFETY DATA IMPROVEMENTS § 1335.6 Strategic plan. A strategic plan shall— (a) Be a multi-year plan that identifies and...

  8. 23 CFR 1335.6 - Strategic plan.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 23 Highways 1 2012-04-01 2012-04-01 false Strategic plan. 1335.6 Section 1335.6 Highways NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION STATE HIGHWAY SAFETY DATA IMPROVEMENTS § 1335.6 Strategic plan. A strategic plan shall— (a) Be a multi-year plan that identifies and...

  9. Drug Safety

    MedlinePlus

    ... over-the-counter drug. The FDA evaluates the safety of a drug by looking at Side effects ... clinical trials The FDA also monitors a drug's safety after approval. For you, drug safety means buying ...

  10. Nuclear regulation and safety

    SciTech Connect

    Hendrie, J.M.

    1982-01-01

    Nuclear regulation and safety are discussed from the standpoint of a hypothetical country that is in the process of introducing a nuclear power industry and setting up a regulatory system. The national policy is assumed to be in favor of nuclear power. The regulators will have responsibility for economic, reliable electric production as well as for safety. Reactor safety is divided into three parts: shut it down, keep it covered, take out the afterheat. Emergency plans also have to be provided. Ways of keeping the core covered with water are discussed. (DLC)

  11. Emergency preparedness and planning

    NASA Technical Reports Server (NTRS)

    Bouvier, Kenneth

    1993-01-01

    Monsanto's emergency response plan in dealing with hazardous materials at their facilities is presented. Topics discussed include the following: CPR training; emergency medial training; incident reports; contractor injuries; hazardous materials transport; evacuation; and other industrial safety concerns.

  12. 11. Strategic planning.

    PubMed

    2014-05-01

    There are several types of planning processes and plans, including strategic, operational, tactical, and contingency. For this document, operational planning includes tactical planning. This chapter examines the strategic planning process and includes an introduction into disaster response plans. "A strategic plan is an outline of steps designed with the goals of the entire organisation as a whole in mind, rather than with the goals of specific divisions or departments". Strategic planning includes all measures taken to provide a broad picture of what must be achieved and in which order, including how to organise a system capable of achieving the overall goals. Strategic planning often is done pre-event, based on previous experience and expertise. The strategic planning for disasters converts needs into a strategic plan of action. Strategic plans detail the goals that must be achieved. The process of converting needs into plans has been deconstructed into its components and includes consideration of: (1) disaster response plans; (2) interventions underway or planned; (3) available resources; (4) current status vs. pre-event status; (5) history and experience of the planners; and (6) access to the affected population. These factors are tempered by the local: (a) geography; (b) climate; (c) culture; (d) safety; and (e) practicality. The planning process consumes resources (costs). All plans must be adapted to the actual conditions--things never happen exactly as planned.

  13. An initial radiation safety needs assessment of Costa Rica: the South Texas Chapter of the Health Physics Society's strategic planning appraisal for participation in the "Radiation Safety Without Borders" initiative.

    PubMed

    Emery, Robert J; Felknor, S A

    2002-05-01

    In response to the Health Physics Society's recent 'radiation safety without borders" initiative, the South Texas Chapter of the Health Physics Society selected Costa Rica as its partner country of choice. To develop an understanding of the radiation safety needs of this country, the fall 2001 University of Texas Health Science Center at Houston School of Public Health Environmental Radiation and Radioactivity class was tasked with the assignment of assessing the possible radiation safety needs and concerns for this country. The assignment culminated in a class presentation to the membership of the South Texas Chapter during its annual fall meeting. Using library and web based resources, tile students reviewed a number of public health and radiation-related topics. Life expectancies were found to be equivalent to the United States, even though significant differences in per capita health expenditures were noted. Costa Rica exhibited lower population mortality rates from major causes such as cardiovascular diseases, neoplasms, and external sources. Maternal and infant mortality rates were found to be much higher in Costa Rica than in the United States. Naturally occurring radiation sources such as uranium deposits were not identified as apparent major radiation issues of concern, although ultraviolet radiation exposures are consistently high. Several recent events in the country and the region involving patient overexposures suggest that concerns are likely focused on ensuring the proper use and maintenance of healing arts radiation equipment. The lack of available information on radioactive waste disposal suggests that waste handling also may be an issue warranting attention. The exercise proved to be very educational for the students, and the information gathered will serve to focus the Chapter's efforts when technical exchanges are initiated. The importance of linking this initiative to other existing programs within the country is also discussed.

  14. Shuttle Upgrade Plan

    NASA Technical Reports Server (NTRS)

    2000-01-01

    This viewgraph presentation gives an overview of the Space Shuttle upgrade plan, including details on safety enhancements, reliability and maintainability improvements, investment protection (mission life remaining), Next Generation Reusable Launch Vehicle technologies, HEDS exploration strategic goals, and upgrades for safety and supportability.

  15. School Fire Safety Manual.

    ERIC Educational Resources Information Center

    Arkansas State Dept. of Education, Little Rock. General Education Div.

    This manual provides the background information necessary for the planning of school fire safety programs by local school officials, particularly in Arkansas. The manual first discusses the need for such programs and cites the Arkansas state law regarding them. Policies established by the Arkansas State Board of Education to implement the legal…

  16. Safety Awareness & Communications Internship

    NASA Technical Reports Server (NTRS)

    Jefferson, Zanani

    2015-01-01

    The projects that I have worked on during my internships were updating the JSC Safety & Health Action Team JSAT Employee Guidebook, conducting a JSC mishap case study, preparing for JSC Today Close Call success stories, and assisting with event planning and awareness.

  17. School Safety Review Checklist

    ERIC Educational Resources Information Center

    Vermont Department of Education, 2005

    2005-01-01

    The School Safety Review Checklist is an important component of the broader school crisis resources that have been developed by the Vermont School Crisis Planning Team. The Team is comprised of members from the law enforcement, emergency management, health, and education organizations who have worked throughout the year to update school and…

  18. Safety System Design for Technology Education. A Safety Guide for Technology Education Courses K-12.

    ERIC Educational Resources Information Center

    North Carolina State Dept. of Public Instruction, Raleigh. Div. of Vocational Education.

    This manual is designed to involve both teachers and students in planning and controlling a safety system for technology education classrooms. The safety program involves students in the design and maintenance of the system by including them in the analysis of the classroom environment, job safety analysis, safety inspection, and machine safety…

  19. Safety in the Science Classroom

    ERIC Educational Resources Information Center

    Online Submission, 2006

    2006-01-01

    The goal of this K-12 science safety resource is to bring together information needed by administrators, planners, teachers and support staff to help them make sound decisions regarding science safety. The document identifies areas for decision making and action at a variety of levels. It supports planning and action by providing information on…

  20. Railroad safety program, task 2

    NASA Technical Reports Server (NTRS)

    1983-01-01

    Aspects of railroad safety and the preparation of a National Inspection Plan (NIP) for rail safety improvement are examined. Methodology for the allocation of inspection resources, preparation of a NIP instruction manual, and recommendations for future NIP, are described. A statistical analysis of regional rail accidents is presented with causes and suggested preventive measures included.

  1. New Applications of Gamma Spectroscopy: Characterization Tools for D&D Process Development, Inventory Reduction Planning & Shipping, Safety Analysis & Facility Management During the Heavy Element Facility Risk Reduction Program

    SciTech Connect

    Mitchell, M; Anderson, B; Gray, L; Vellinger, R; West, M; Gaylord, R; Larson, J; Jones, G; Shingleton, J; Harris, L; Harward, N

    2006-01-23

    Novel applications of gamma ray spectroscopy for D&D process development, inventory reduction, safety analysis and facility management are discussed in this paper. These applications of gamma spectroscopy were developed and implemented during the Risk Reduction Program (RPP) to successfully downgrade the Heavy Element Facility (B251) at Lawrence Livermore National Laboratory (LLNL) from a Category II Nuclear Facility to a Radiological Facility. Non-destructive assay in general, gamma spectroscopy in particular, were found to be important tools in project management, work planning, and work control (''Expect the unexpected and confirm the expected''), minimizing worker dose, and resulted in significant safety improvements and operational efficiencies. Inventory reduction activities utilized gamma spectroscopy to identify and confirm isotopics of legacy inventory, ingrowth of daughter products and the presence of process impurities; quantify inventory; prioritize work activities for project management; and to supply information to satisfy shipper/receiver documentation requirements. D&D activities utilize in-situ gamma spectroscopy to identify and confirm isotopics of legacy contamination; quantify contamination levels and monitor the progress of decontamination efforts; and determine the point of diminishing returns in decontaminating enclosures and glove boxes containing high specific activity isotopes such as {sup 244}Cm and {sup 238}Pu. In-situ gamma spectroscopy provided quantitative comparisons of several decontamination techniques (e.g. TLC-free Stripcoat{trademark}, Radiac{trademark} wash, acid wash, scrubbing) and was used as a part of an iterative process to determine the appropriate level of decontamination and optimal cost to benefit ratio. Facility management followed a formal, rigorous process utilizing an independent, state certified, peer-reviewed gamma spectroscopy program, in conjunction with other characterization techniques, process knowledge, and

  2. Safety Evaluation Report for the Tennessee Valley Authority's Plan to Decommission its Low-Level Radioactive Waste Burial Site at Muscle Shoals, Alabama

    SciTech Connect

    Gant, K.S.; Kettelle, R.H.

    1998-11-01

    From 1966 to 1981, the Tennessee Valley Authority (TVA) operated a burial site, licensed under the former 10 CFR 20.304, for low-level radioactive waste on its Muscle Shoals, Alabama, reservation. TVA submitted a decommissioning plan for the burial site and requested approval for unrestricted use of the site. The Nuclear Regulatory Commission requested Oak Ridge National Laboratory (ORNL) to evaluate this plan to determine if the site meets the radiological requirements for unrestricted use as specified in 10 CFR 20.1402; that is, an average member of the critical group would not receive more than 25 mrem/y from residual radioactivity at the TVA Low-Level Radioactive Waste Burial Site and the radioactivity has been reduced to levels as low as reasonably achievable (ALARA).

  3. An Exploratory Study of a Computer-Assisted Abuse Awareness and Safety Planning Program for Men With Disabilities: The Men's Safer and Stronger Program.

    PubMed

    Oschwald, Mary; Lund, Emily M; Latorre, Allyn; Shelton, Rollin; Hughes, Rosemary B; Liston, Bob; Flaherty, Michael C; Powers, Laurie E

    2015-01-01

    Interpersonal violence (IPV) is a serious and often unrecognized problem for men with disabilities (MWD). However, abuse awareness programs and outcome measures have not been systematically evaluated in MWD. This article reports findings from an exploratory study (n = 31) of the Safer and Stronger Program for Men with Disabilities (Men's SSP), an audio computer-assisted self-interview (ACASI) abuse awareness program. Preliminary findings suggest it is sensitive toward detecting abuse and it allows MWD to privately and independently self-identify IPV experiences. Preliminary psychometric data on a battery of abuse and safety awareness outcome measures suggest that they are reliable in this population. PMID:25671458

  4. An Exploratory Study of a Computer-Assisted Abuse Awareness and Safety Planning Program for Men With Disabilities: The Men's Safer and Stronger Program.

    PubMed

    Oschwald, Mary; Lund, Emily M; Latorre, Allyn; Shelton, Rollin; Hughes, Rosemary B; Liston, Bob; Flaherty, Michael C; Powers, Laurie E

    2015-01-01

    Interpersonal violence (IPV) is a serious and often unrecognized problem for men with disabilities (MWD). However, abuse awareness programs and outcome measures have not been systematically evaluated in MWD. This article reports findings from an exploratory study (n = 31) of the Safer and Stronger Program for Men with Disabilities (Men's SSP), an audio computer-assisted self-interview (ACASI) abuse awareness program. Preliminary findings suggest it is sensitive toward detecting abuse and it allows MWD to privately and independently self-identify IPV experiences. Preliminary psychometric data on a battery of abuse and safety awareness outcome measures suggest that they are reliable in this population.

  5. [Supervising road safety in Peru].

    PubMed

    Sagástegui, Freddy

    2010-06-01

    In this article some problems in road safety are described, which have been detected by the Ombudsman of Peru, as part of its role of public administration supervisor, amongst these problems we mention: lack of and inadequate elaboration of the statistics on road traffic accidents, the inconsistency of the National Council for Road Security and the lack of responsibility of the local and regional governments reflected by the lack of application of the National Plan of Road Safety. Facing this, the Ombudsman suggests that the State develops a rigorous statistical system, strengthens the National Council of Road Safety and that the different sectors of the government develop the mentioned National Plan.

  6. Vaccine Safety

    MedlinePlus

    ... During Pregnancy Frequently Asked Questions about Vaccine Recalls Historical Vaccine Safety Concerns FAQs about GBS and Menactra ... CISA Resources for Healthcare Professionals Evaluation Current Studies Historical Background 2001-12 Publications Technical Reports Vaccine Safety ...

  7. 7 CFR 25.202 - Strategic plan.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 1 2014-01-01 2014-01-01 false Strategic plan. 25.202 Section 25.202 Agriculture... Procedure § 25.202 Strategic plan. (a) Principles of strategic plan. The strategic plan included in the... transportation, education, and public safety. (b) Minimum requirements. The strategic plan must: (1) Describe...

  8. 7 CFR 25.202 - Strategic plan.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 1 2012-01-01 2012-01-01 false Strategic plan. 25.202 Section 25.202 Agriculture... Procedure § 25.202 Strategic plan. (a) Principles of strategic plan. The strategic plan included in the... transportation, education, and public safety. (b) Minimum requirements. The strategic plan must: (1) Describe...

  9. 7 CFR 25.202 - Strategic plan.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 1 2013-01-01 2013-01-01 false Strategic plan. 25.202 Section 25.202 Agriculture... Procedure § 25.202 Strategic plan. (a) Principles of strategic plan. The strategic plan included in the... transportation, education, and public safety. (b) Minimum requirements. The strategic plan must: (1) Describe...

  10. 7 CFR 25.202 - Strategic plan.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 1 2011-01-01 2011-01-01 false Strategic plan. 25.202 Section 25.202 Agriculture... Procedure § 25.202 Strategic plan. (a) Principles of strategic plan. The strategic plan included in the... transportation, education, and public safety. (b) Minimum requirements. The strategic plan must: (1) Describe...

  11. Did you have an impact? A theory-based method for planning and evaluating knowledge-transfer and exchange activities in occupational health and safety.

    PubMed

    Kramer, Desré M; Wells, Richard P; Carlan, Nicolette; Aversa, Theresa; Bigelow, Philip P; Dixon, Shane M; McMillan, Keith

    2013-01-01

    Few evaluation tools are available to assess knowledge-transfer and exchange interventions. The objective of this paper is to develop and demonstrate a theory-based knowledge-transfer and exchange method of evaluation (KEME) that synthesizes 3 theoretical frameworks: the promoting action on research implementation of health services (PARiHS) model, the transtheoretical model of change, and a model of knowledge use. It proposes a new term, keme, to mean a unit of evidence-based transferable knowledge. The usefulness of the evaluation method is demonstrated with 4 occupational health and safety knowledge transfer and exchange (KTE) implementation case studies that are based upon the analysis of over 50 pre-existing interviews. The usefulness of the evaluation model has enabled us to better understand stakeholder feedback, frame our interpretation, and perform a more comprehensive evaluation of the knowledge use outcomes of our KTE efforts. PMID:23498710

  12. Safety Handbook.

    ERIC Educational Resources Information Center

    Montgomery County Public Schools, Rockville, MD.

    Safety policies, procedures, and related information are presented in this manual to assist school personnel in a continuing program of accident prevention. Chapter 1 discusses safety education and accident prevention in general. Chapter 2 covers traffic regulations relating to school safety patrols, school bus transportation, bicycles, and…

  13. An Operational Safety and Health Program.

    ERIC Educational Resources Information Center

    Uhorchak, Robert E.

    1983-01-01

    Describes safety/health program activities at Research Triangle Institute (North Carolina). These include: radioisotope/radiation and hazardous chemical/carcinogen use, training, monitoring, disposal; chemical waste management; air monitoring and analysis; medical program; fire safety/training, including emergency planning; Occupational Safety and…

  14. Aerospace Safety Advisory Panel

    NASA Technical Reports Server (NTRS)

    1999-01-01

    This report covers the activities of the Aerospace Safety Advisory Panel (ASAP) for calendar year 1998-a year of sharp contrasts and significant successes at NASA. The year opened with the announcement of large workforce cutbacks. The slip in the schedule for launching the International Space Station (ISS) created a 5-month hiatus in Space Shuttle launches. This slack period ended with the successful and highly publicized launch of the STS-95 mission. As the year closed, ISS assembly began with the successful orbiting and joining of the Functional Cargo Block (FGB), Zarya, from Russia and the Unity Node from the United States. Throughout the year, the Panel maintained its scrutiny of NASAs safety processes. Of particular interest were the potential effects on safety of workforce reductions and the continued transition of functions to the Space Flight Operations Contractor. Attention was also given to the risk management plans of the Aero-Space Technology programs, including the X-33, X-34, and X-38. Overall, the Panel concluded that safety is well served for the present. The picture is not as clear for the future. Cutbacks have limited the depth of talent available. In many cases, technical specialties are "one deep." The extended hiring freeze has resulted in an older workforce that will inevitably suffer significant departures from retirements in the near future. The resulting "brain drain" could represent a future safety risk unless appropriate succession planning is started expeditiously. This and other topics are covered in the section addressing workforce. In the case of the Space Shuttle, beneficial and mandatory safety and operational upgrades are being delayed because of a lack of sufficient present funding. Likewise, the ISS has little flexibility to begin long lead-time items for upgrades or contingency planning.

  15. Aerospace Safety Advisory Panel

    NASA Technical Reports Server (NTRS)

    2002-01-01

    This Annual Report of the Aerospace Safety Advisory Panel (ASAP) presents results of activities during calendar year 2001. The year was marked by significant achievements in the Space Shuttle and International Space Station (ISS) programs and encouraging accomplishments by the Aerospace Technology Enterprise. Unfortunately, there were also disquieting mishaps with the X-43, a LearJet, and a wind tunnel. Each mishap was analyzed in an orderly process to ascertain causes and derive lessons learned. Both these accomplishments and the responses to the mishaps led the Panel to conclude that safety and risk management is currently being well served within NASA. NASA's operations evidence high levels of safety consciousness and sincere efforts to place safety foremost. Nevertheless, the Panel's safety concerns have never been greater. This dichotomy has arisen because the focus of most NASA programs has been directed toward program survival rather than effective life cycle planning. Last year's Annual Report focused on the need for NASA to adopt a realistically long planning horizon for the aging Space Shuttle so that safety would not erode. NASA's response to the report concurred with this finding. Nevertheless, there has been a greater emphasis on current operations to the apparent detriment of long-term planning. Budget cutbacks and shifts in priorities have severely limited the resources available to the Space Shuttle and ISS for application to risk-reduction and life-extension efforts. As a result, funds originally intended for long-term safety-related activities have been used for operations. Thus, while safety continues to be well served at present, the basis for future safety has eroded. Section II of this report develops this theme in more detail and presents several important, overarching findings and recommendations that apply to many if not all of NASA's programs. Section III of the report presents other significant findings, recommendations and supporting

  16. National Safety Council

    MedlinePlus

    ... Introduction Safety Management Systems Workplace Safety Consulting Employee Perception Surveys Research Journey to Safety Excellence Join the ... Safety Safety Management Systems Workplace Safety Consulting Employee Perception Surveys Research Journey to Safety Excellence Join the ...

  17. Patient safety: the doctor's perspective.

    PubMed

    Shemesh, David; Olsha, Oded; Goldin, Ilya; Danin, Sigalit

    2015-01-01

    Medical errors can be defined as the failure of a planned action to be completed as intended or the use of a wrong plan to achieve an aim. Beyond their economic cost and their cost in human lives, errors cause loss of trust in the healthcare system by patients and diminished satisfaction by both patients and health professionals. There are many evidence-based safety-oriented behaviours and interventions that are easily implemented, such as ultrasound-guided central venous catheter insertion, prevention of catheter-related bloodstream infection and more. In vascular access, the development of research in patient safety has raised a variety of issues requiring study in order to provide the optimal patient safety approach. Patients are major contributors to their own safety, and as such, physicians should develop a new approach to involve them in the cycle of decision making through every step of their treatment. There are many opportunities along this path for the patient to be engaged in safety behaviours and for the access team to ensure such behaviours by employing simple strategies. The advent of the access centre, based on multidisciplinary teamwork, has enhanced the potential to improve patient safety by prevention of errors in planning and performing access surgery, avoiding delay in treatment of access malfunction and improving communication between the team members. However, a significant effort in research is still needed in order to implement intervention by evidence-based data focused on patient safety. PMID:25751565

  18. Patient safety: the doctor's perspective.

    PubMed

    Shemesh, David; Olsha, Oded; Goldin, Ilya; Danin, Sigalit

    2015-01-01

    Medical errors can be defined as the failure of a planned action to be completed as intended or the use of a wrong plan to achieve an aim. Beyond their economic cost and their cost in human lives, errors cause loss of trust in the healthcare system by patients and diminished satisfaction by both patients and health professionals. There are many evidence-based safety-oriented behaviours and interventions that are easily implemented, such as ultrasound-guided central venous catheter insertion, prevention of catheter-related bloodstream infection and more. In vascular access, the development of research in patient safety has raised a variety of issues requiring study in order to provide the optimal patient safety approach. Patients are major contributors to their own safety, and as such, physicians should develop a new approach to involve them in the cycle of decision making through every step of their treatment. There are many opportunities along this path for the patient to be engaged in safety behaviours and for the access team to ensure such behaviours by employing simple strategies. The advent of the access centre, based on multidisciplinary teamwork, has enhanced the potential to improve patient safety by prevention of errors in planning and performing access surgery, avoiding delay in treatment of access malfunction and improving communication between the team members. However, a significant effort in research is still needed in order to implement intervention by evidence-based data focused on patient safety.

  19. Strategic implementation plan

    NASA Technical Reports Server (NTRS)

    1989-01-01

    The Life Science Division of the NASA Office of Space Science and Applications (OSSA) describes its plans for assuring the health, safety, and productivity of astronauts in space, and its plans for acquiring further fundamental scientific knowledge concerning space life sciences. This strategic implementation plan details OSSA's goals, objectives, and planned initiatives. The following areas of interest are identified: operational medicine; biomedical research; space biology; exobiology; biospheric research; controlled ecological life support; flight programs and advance technology development; the life sciences educational program; and earth benefits from space life sciences.

  20. Development of the High Altitude Student Platform

    NASA Astrophysics Data System (ADS)

    Guzik, T. G.; Besse, S.; Calongne, A.; Dominique, A.; Ellison, S. B.; Gould, R.; Granger, D.; Olano, D.; Smith, D.; Stewart, M.; Wefel, J. P.

    2008-11-01

    The High Altitude Student Platform (HASP) was originally conceived to provide student groups with access to the near-space environment for flight durations and experiment capabilities intermediate between what is possible with small sounding balloons and low Earth orbit rocket launches. HASP is designed to carry up to twelve student payloads to an altitude of about 36 km with flight durations of 15 20 h using a small zero-pressure polyethylene film balloon. This provides a flight capability that can be used to flight-test compact satellites, prototypes and other small payloads designed and built by students. HASP includes a standard mechanical, power and communication interface for the student payload to simplify integration and allows the payloads to be fully exercised. Over the last two years a partnership between the NASA Balloon Program Office (BPO), Columbia Scientific Balloon Facility (CSBF), Louisiana State University (LSU), the Louisiana Board of Regents (BoR), and the Louisiana Space Consortium (LaSPACE) has led to the development, construction and, finally, the first flight of HASP with a complement of eight student payloads on September 4, 2006. Here we discuss the primary as-built HASP systems and features, the student payload interface, HASP performance during the first flight and plans for continuing HASP flights. The HASP project maintains a website at http://laspace.lsu.edu/hasp/ where flight application, interface documentation and status information can be obtained.

  1. Skateboard Safety.

    ERIC Educational Resources Information Center

    Della-Giustina, Daniel

    1979-01-01

    The growing number of skateboard injuries clearly indicates a need for both recreational facilities designed exclusively for skateboarders, and for accident- prevention-oriented safety education programs. (LH)

  2. Medication safety.

    PubMed

    Keohane, Carol A; Bates, David W

    2008-03-01

    Patient safety is a state of mind, not a technology. The technologies used in the medical setting represent tools that must be properly designed, used well, and assessed on an on-going basis. Moreover, in all settings, building a culture of safety is pivotal for improving safety, and many nontechnologic approaches, such as medication reconciliation and teaching patients about their medications, are also essential. This article addresses the topic of medication safety and examines specific strategies being used to decrease the incidence of medication errors across various clinical settings.

  3. Another look at safety climate and safety behavior: deepening the cognitive and social mediator mechanisms.

    PubMed

    Fugas, Carla S; Silva, Sílvia A; Meliá, José L

    2012-03-01

    In this study, safety climate literature and the theory of planned behavior were combined to explore the cognitive and social mechanisms that mediate the relationship between organizational safety climate and compliance and proactive safety behaviors. The sample consisted of 356 workers from a transportation organization. Using a multiple mediation design, the results revealed that proactive and compliance safety behaviors are explained by different patterns of combinations of individual and situational factors related to safety. On the one hand, the relationship between organizational safety climate and proactive safety behaviors was mediated by coworkers' descriptive norms and attitudes toward safety. On the other hand, supervisors' injunctive safety norms and perceived behavioral control were the mediator variables between organizational safety climate and compliance safety behaviors. Theoretical and practical implications of the findings are discussed.

  4. Another look at safety climate and safety behavior: deepening the cognitive and social mediator mechanisms.

    PubMed

    Fugas, Carla S; Silva, Sílvia A; Meliá, José L

    2012-03-01

    In this study, safety climate literature and the theory of planned behavior were combined to explore the cognitive and social mechanisms that mediate the relationship between organizational safety climate and compliance and proactive safety behaviors. The sample consisted of 356 workers from a transportation organization. Using a multiple mediation design, the results revealed that proactive and compliance safety behaviors are explained by different patterns of combinations of individual and situational factors related to safety. On the one hand, the relationship between organizational safety climate and proactive safety behaviors was mediated by coworkers' descriptive norms and attitudes toward safety. On the other hand, supervisors' injunctive safety norms and perceived behavioral control were the mediator variables between organizational safety climate and compliance safety behaviors. Theoretical and practical implications of the findings are discussed. PMID:22269531

  5. System Safety Analysis Application Guide. Safety Analysis Report Update Program

    SciTech Connect

    Not Available

    1993-05-01

    Martin Marietta Energy Systems, Inc., (Energy Systems) is committed to performing and documenting safety analyses for facilities it manages for the Department of Energy (DOE). Safety analyses are performed to identify hazards and potential accidents; to analyze the adequacy of measures taken to eliminate, control, or mitigate hazards; and to evaluate potential accidents and determine associated risks. Safety Analysis Reports (SARs) are prepared to document the safety analysis to ensure facilities can be operated safely and in accordance with regulations. SARs include Technical Safety Requirements (TSRs), which are specific technical and administrative requirements that prescribe limits and controls to ensure safe operation of DOE facilities. These documented descriptions and analyses contribute to the authorization basis for facility operation. Energy Systems has established a process to perform Unreviewed Safety Question Determinations (USQDs) for planned changes and as-found conditions that are not described and analyzed in existing safety analyses. The process evaluates changes and as-found conditions to determine whether revisions to the authorization basis must be reviewed and approved by DOE. There is an Unreviewed Safety Question (USQ) if a change introduces conditions not bounded by the facility authorization basis. When it is necessary to request DOE approval to revise the authorization basis, preparation of a System Safety Analysis (SSA) is recommended. This application guide describes the process of preparing an SSA and the desired contents of an SSA. Guidance is provided on how to identify items and practices which are important to safety; how to determine the credibility and significance of consequences of proposed accident scenarios; how to evaluate accident prevention and mitigation features of the planned change; and how to establish special requirements to ensure that a change can be implemented with adequate safety.

  6. Lab Safety.

    ERIC Educational Resources Information Center

    West, Sandra S.

    1991-01-01

    In response to the Texas Hazardous Communication Act (THCA) of 1986 which raised many new health and liability issues regarding students in science laboratories, a laboratory safety survey was generated for use in evaluating laboratory safety. This article contains the easy-to-use survey. (ZWH)

  7. Safety Systems

    ERIC Educational Resources Information Center

    Halligan, Tom

    2009-01-01

    Colleges across the country are rising to the task by implementing safety programs, response strategies, and technologies intended to create a secure environment for teachers and students. Whether it is preparing and responding to a natural disaster, health emergency, or act of violence, more schools are making campus safety a top priority. At…

  8. Safety First

    ERIC Educational Resources Information Center

    Taft, Darryl

    2011-01-01

    Ned Miller does not take security lightly. As director of campus safety and emergency management at the Des Moines Area Community College (DMACC), any threat requires serious consideration. As community college administrators adopt a more proactive approach to campus safety, many institutions are experimenting with emerging technologies, including…

  9. A Geospatial Mixed Methods Approach to Assessing Campus Safety

    ERIC Educational Resources Information Center

    Hites, Lisle S.; Fifolt, Matthew; Beck, Heidi; Su, Wei; Kerbawy, Shatomi; Wakelee, Jessica; Nassel, Ariann

    2013-01-01

    Background: While there is no panacea for alleviating campus safety concerns, safety experts agree that one of the key components to an effective campus security plan is monitoring the environment. Despite previous attempts to measure campus safety, quantifying perceptions of fear, safety, and risk remains a challenging issue. Since perceptions of…

  10. Reactor operation safety information document

    SciTech Connect

    Not Available

    1990-01-01

    The report contains a reactor facility description which includes K, P, and L reactor sites, structures, operating systems, engineered safety systems, support systems, and process and effluent monitoring systems; an accident analysis section which includes cooling system anomalies, radioactive materials releases, and anticipated transients without scram; a summary of onsite doses from design basis accidents; severe accident analysis (reactor core disruption); a description of operating contractor organization and emergency planning; and a summary of reactor safety evolution. (MB)

  11. LNG Safety Assessment Evaluation Methods

    SciTech Connect

    Muna, Alice Baca; LaFleur, Angela Christine

    2015-05-01

    Sandia National Laboratories evaluated published safety assessment methods across a variety of industries including Liquefied Natural Gas (LNG), hydrogen, land and marine transportation, as well as the US Department of Defense (DOD). All the methods were evaluated for their potential applicability for use in the LNG railroad application. After reviewing the documents included in this report, as well as others not included because of repetition, the Department of Energy (DOE) Hydrogen Safety Plan Checklist is most suitable to be adapted to the LNG railroad application. This report was developed to survey industries related to rail transportation for methodologies and tools that can be used by the FRA to review and evaluate safety assessments submitted by the railroad industry as a part of their implementation plans for liquefied or compressed natural gas storage ( on-board or tender) and engine fueling delivery systems. The main sections of this report provide an overview of various methods found during this survey. In most cases, the reference document is quoted directly. The final section provides discussion and a recommendation for the most appropriate methodology that will allow efficient and consistent evaluations to be made. The DOE Hydrogen Safety Plan Checklist was then revised to adapt it as a methodology for the Federal Railroad Administration’s use in evaluating safety plans submitted by the railroad industry.

  12. 76 FR 18669 - Safety Zone, Newport River; Morehead City, NC

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-04-05

    ... Federal Register (73 FR 3316). Public Meeting We do not now plan to hold a public meeting. But you may... River high rise bridge in Carteret County, NC. This safety zone is necessary to provide for safety...

  13. Assuring the quality of safety analyses and safety analysis documentation

    SciTech Connect

    J. E. Johnson

    2000-05-03

    Planning, preparation, and submittal of safety analysis reports might be pursued in a manner similar to a quality-related procurement, where customer needs, expectations and acceptance criteria are established in advance. Then the product/service provider, the contractor, should apply various quality control processes to assure the desired characteristics of the product safety analysis documents. Improving the quality and acceptability to DOE of safety documents at first submittal should result in a more expeditious DOE review and approval process, thereby reducing costs of network and recycle through reviews.

  14. Assuring the Quality of Safety Analyses and Safety Analysis Documentation

    SciTech Connect

    Johnson, John Edwin

    2000-05-01

    Planning, preparation, and submittal of safety analysis reports might be pursued in a manner similar to a quality-related procurement, where customer needs, expectations and acceptance criteria are established in advance. Then the product/service provider, the contractor, should apply various quality control processes to assure the desired characteristics of the product safety analysis documents. Improving the quality and acceptability to DOE of safety documents at first submittal should result in a more expeditious DOE review and approval process, thereby reducing costs of network and recycle through reviews.

  15. Aerospace Safety Advisory Panel

    NASA Technical Reports Server (NTRS)

    1999-01-01

    This report covers the activities of the Aerospace Safety Advisory Panel (ASAP) for calendar year 1998-a year of sharp contrasts and significant successes at NASA. The year opened with the announcement of large workforce cutbacks. The slip in the schedule for launching the International Space Station (ISS) created a five-month hiatus in Space Shuttle launches. This slack period ended with the successful and highly publicized launch of the STS-95 mission. As the year closed, ISS assembly began with the successful orbiting and joining of the Functional Cargo Block (FGB), Zarya, from Russia and the Unity Node from the United States. Throughout the year, the Panel maintained its scrutiny of NASA's safety processes. Of particular interest were the potential effects on safety of workforce reductions and the continued transition of functions to the Space Flight Operations Contractor. Attention was also given to the risk management plans of the Aero-Space Technology programs, including the X-33, X-34, and X-38. Overall, the Panel concluded that safety is well served for the present. The picture is not as clear for the future. Cutbacks have limited the depth of talent available. In many cases, technical specialties are 'one deep.' The extended hiring freeze has resulted in an older workforce that will inevitably suffer significant departures from retirements in the near future. The resulting 'brain drain' could represent a future safety risk unless appropriate succession planning is started expeditiously. This and other topics are covered in the section addressing workforce. The major NASA programs are also limited in their ability to plan property for the future. This is of particular concern for the Space Shuttle and ISS because these programs are scheduled to operate well into the next century. In the case of the Space Shuttle, beneficial and mandatory safety and operational upgrades are being delayed because of a lack of sufficient present funding. Likewise, the ISS has

  16. 23 CFR 1200.25 - Improvement plan.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 23 Highways 1 2012-04-01 2012-04-01 false Improvement plan. 1200.25 Section 1200.25 Highways... Implementation and Management of the Highway Safety Program § 1200.25 Improvement plan. If a review of the Annual... improvement plan. This plan will detail strategies, program activities, and funding targets to meet...

  17. Implementation of the INEEL Safety Analyst Training Standard

    SciTech Connect

    Hochhalter, E Eugene

    2000-05-01

    The Idaho Nuclear Technology and Engineering Center (INTEC) safety analysis units at the Idaho National Engineering and Environmental Laboratory (INEEL) are in the process of implementing the recently issued INEEL Safety Analyst Training Standard (STD-1107). Safety analyst training and qualifications are integral to the development and maintenance of core safety analysis capabilities. The INEEL Safety Analyst Training Standard (STD-1107) was developed directly from EFCOG Training Subgroup draft safety analyst training plan template, but has been adapted to the needs and requirements of the INEEL safety analysis community. The implementation of this Safety Analyst Training Standard is part of the Integrated Safety Management System (ISMS) Phase II Implementation currently underway at the INEEL. The objective of this paper is to discuss (1) the INEEL Safety Analyst Training Standard, (2) the development of the safety analyst individual training plans, (3) the implementation issues encountered during this initial phase of implementation, (4) the solutions developed, and (5) the implementation activities remaining to be completed.

  18. Implementation of the INEEL safety analyst training standard

    SciTech Connect

    E. E. Hochhalter

    2000-04-28

    The Idaho Nuclear Technology and Engineering Center (INTEC) safety analysis units at the Idaho National Engineering and Environmental Laboratory (INEEL) are in the process of implementing the recently issued INEEL Safety Analyst Training Standard (STD-1107). Safety analyst training and qualifications are integral to the development and maintenance of core safety analysis capabilities. The INEEL Safety Analyst Training Standard (STD-1107) was developed directly from EFCOG Training Subgroup draft safety analyst training plan template, but has been adapted to the needs and requirements of the INEEL safety analysis community. The implementation of this Safety Analyst Training Standard is part of the Integrated Safety Management System (ISMS) Phase II Implementation currently underway at the INEEL. The objective of this paper is to discuss (1) the INEEL Safety Analyst Training Standard, (2) the development of the safety analyst individual training plans, (3) the implementation issues encountered during this initial phase of implementation, (4) the solutions developed, and (5) the implementation activities remaining to be completed.

  19. NASA's Software Safety Standard

    NASA Technical Reports Server (NTRS)

    Ramsay, Christopher M.

    2007-01-01

    NASA relies more and more on software to control, monitor, and verify its safety critical systems, facilities and operations. Since the 1960's there has hardly been a spacecraft launched that does not have a computer on board that will provide command and control services. There have been recent incidents where software has played a role in high-profile mission failures and hazardous incidents. For example, the Mars Orbiter, Mars Polar Lander, the DART (Demonstration of Autonomous Rendezvous Technology), and MER (Mars Exploration Rover) Spirit anomalies were all caused or contributed to by software. The Mission Control Centers for the Shuttle, ISS, and unmanned programs are highly dependant on software for data displays, analysis, and mission planning. Despite this growing dependence on software control and monitoring, there has been little to no consistent application of software safety practices and methodology to NASA's projects with safety critical software. Meanwhile, academia and private industry have been stepping forward with procedures and standards for safety critical systems and software, for example Dr. Nancy Leveson's book Safeware: System Safety and Computers. The NASA Software Safety Standard, originally published in 1997, was widely ignored due to its complexity and poor organization. It also focused on concepts rather than definite procedural requirements organized around a software project lifecycle. Led by NASA Headquarters Office of Safety and Mission Assurance, the NASA Software Safety Standard has recently undergone a significant update. This new standard provides the procedures and guidelines for evaluating a project for safety criticality and then lays out the minimum project lifecycle requirements to assure the software is created, operated, and maintained in the safest possible manner. This update of the standard clearly delineates the minimum set of software safety requirements for a project without detailing the implementation for those

  20. Software safety

    NASA Technical Reports Server (NTRS)

    Leveson, Nancy

    1987-01-01

    Software safety and its relationship to other qualities are discussed. It is shown that standard reliability and fault tolerance techniques will not solve the safety problem for the present. A new attitude requires: looking at what you do NOT want software to do along with what you want it to do; and assuming things will go wrong. New procedures and changes to entire software development process are necessary: special software safety analysis techniques are needed; and design techniques, especially eliminating complexity, can be very helpful.

  1. Safety Tips.

    ERIC Educational Resources Information Center

    Nagel, Miriam C., Ed.

    1984-01-01

    Outlines a cooperative effort in Iowa to eliminate dangerous or unwanted chemicals from school science storerooms. Also reviews the Council of State Science Supervisor's safety program and discusses how to prevent cuts and punctures from jagged glass tubing. (JN)

  2. Hitting the Highway? Keep Safety in Mind

    MedlinePlus

    ... medlineplus.gov/news/fullstory_160238.html Hitting the Highway? Keep Safety in Mind Planning ahead is essential ... U.S. Department of Health and Human Services, or federal policy. More Health News on: Traveler's Health Recent ...

  3. NASA ELV Payload Safety Program Information Exchange

    NASA Technical Reports Server (NTRS)

    Staubus, Cal; Palo, Tom; Dook, Mike; Donovan, Shawn

    2007-01-01

    This presentation details the Expendable Launch Vehicle (ELV) Payload Safety Program in its development and plan for implementation. It is an overview of the program's policies, process and requirements.

  4. Disaster Planning Guide for School Administrators.

    ERIC Educational Resources Information Center

    Kansas State Dept. of Education, Topeka.

    This guide for Kansas school administrators will provide a method by which positive safety and emergency planning can be effected. Safety and emergency planning are those efforts by school administrators, teachers, and other staff personnel to provide for a total environment of protection. State, county, and local governmental agencies should…

  5. 14 CFR 415.119 - Launch plans.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... TRANSPORTATION LICENSING LAUNCH LICENSE Safety Review and Approval for Launch of an Expendable Launch Vehicle From a Non-Federal Launch Site § 415.119 Launch plans. An applicant's safety review document must... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Launch plans. 415.119 Section...

  6. 14 CFR 415.119 - Launch plans.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... TRANSPORTATION LICENSING LAUNCH LICENSE Safety Review and Approval for Launch of an Expendable Launch Vehicle From a Non-Federal Launch Site § 415.119 Launch plans. An applicant's safety review document must... 14 Aeronautics and Space 4 2011-01-01 2011-01-01 false Launch plans. 415.119 Section...

  7. 14 CFR 415.119 - Launch plans.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... TRANSPORTATION LICENSING LAUNCH LICENSE Safety Review and Approval for Launch of an Expendable Launch Vehicle From a Non-Federal Launch Site § 415.119 Launch plans. An applicant's safety review document must... 14 Aeronautics and Space 4 2012-01-01 2012-01-01 false Launch plans. 415.119 Section...

  8. 14 CFR 431.41 - Communications plan.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... TRANSPORTATION LICENSING LAUNCH AND REENTRY OF A REUSABLE LAUNCH VEHICLE (RLV) Safety Review and Approval for Launch and Reentry of a Reusable Launch Vehicle § 431.41 Communications plan. (a) An applicant shall submit a plan providing vehicle safety operations personnel communications procedures during the...

  9. 14 CFR 431.41 - Communications plan.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... TRANSPORTATION LICENSING LAUNCH AND REENTRY OF A REUSABLE LAUNCH VEHICLE (RLV) Safety Review and Approval for Launch and Reentry of a Reusable Launch Vehicle § 431.41 Communications plan. (a) An applicant shall submit a plan providing vehicle safety operations personnel communications procedures during the...

  10. 14 CFR 415.119 - Launch plans.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... TRANSPORTATION LICENSING LAUNCH LICENSE Safety Review and Approval for Launch of an Expendable Launch Vehicle From a Non-Federal Launch Site § 415.119 Launch plans. An applicant's safety review document must... 14 Aeronautics and Space 4 2013-01-01 2013-01-01 false Launch plans. 415.119 Section...

  11. Chemical hygiene plan

    SciTech Connect

    Not Available

    1994-09-01

    This plan was written to administer and monitor safety measures and chemical hygiene principles in the TAC Uranium Mill Tailing Remedial Action Project sample preparation facility in Albuquerque, New Mexico. It applies to toxic and/or hazardous materials to radioactive materials.

  12. School Planning Safe Transporting.

    ERIC Educational Resources Information Center

    New Jersey State Dept. of Education, Trenton. Bureau of Pupil Transportation.

    Prepared for boards of education and municipal planning authorities, school site selection is related to school bus safety. Consideration of direction and density of traffic flow, street crossings, curbing, drainage, road width, parking areas, number of pupils and personnel, number of buses, method of transportation, schedules and extra-curricular…

  13. Threat Assessment Plans

    ERIC Educational Resources Information Center

    Pascopella, Angela

    2008-01-01

    With every new case of school violence, district leaders are urged to be proactive in hopes of averting potential violence. Experts say part of that proactive work comes from a threat assessment plan that every district should have. While every district that receives funds from the U.S. Department of Education for school safety is required to have…

  14. Monitoring product safety in the postmarketing environment.

    PubMed

    Sharrar, Robert G; Dieck, Gretchen S

    2013-10-01

    The safety profile of a medicinal product may change in the postmarketing environment. Safety issues not identified in clinical development may be seen and need to be evaluated. Methods of evaluating spontaneous adverse experience reports and identifying new safety risks include a review of individual reports, a review of a frequency distribution of a list of the adverse experiences, the development and analysis of a case series, and various ways of examining the database for signals of disproportionality, which may suggest a possible association. Regulatory agencies monitor product safety through a variety of mechanisms including signal detection of the adverse experience safety reports in databases and by requiring and monitoring risk management plans, periodic safety update reports and postauthorization safety studies. The United States Food and Drug Administration is working with public, academic and private entities to develop methods for using large electronic databases to actively monitor product safety. Important identified risks will have to be evaluated through observational studies and registries.

  15. System safety education focused on flight safety

    NASA Technical Reports Server (NTRS)

    Holt, E.

    1971-01-01

    The measures necessary for achieving higher levels of system safety are analyzed with an eye toward maintaining the combat capability of the Air Force. Several education courses were provided for personnel involved in safety management. Data include: (1) Flight Safety Officer Course, (2) Advanced Safety Program Management, (3) Fundamentals of System Safety, and (4) Quantitative Methods of Safety Analysis.

  16. Aerospace safety advisory panel

    NASA Technical Reports Server (NTRS)

    1995-01-01

    The Aerospace Safety Advisory Panel (ASAP) monitored NASA's activities and provided feedback to the NASA Administrator, other NASA officials and Congress throughout the year. Particular attention was paid to the Space Shuttle, its launch processing and planned and potential safety improvements. The Panel monitored Space Shuttle processing at the Kennedy Space Center (KSC) and will continue to follow it as personnel reductions are implemented. There is particular concern that upgrades in hardware, software, and operations with the potential for significant risk reduction not be overlooked due to the extraordinary budget pressures facing the agency. The authorization of all of the Space Shuttle Main Engine (SSME) Block II components portends future Space Shuttle operations at lower risk levels and with greater margins for handling unplanned ascent events. Throughout the year, the Panel attempted to monitor the safety activities related to the Russian involvement in both space and aeronautics programs. This proved difficult as the working relationships between NASA and the Russians were still being defined as the year unfolded. NASA's concern for the unique safety problems inherent in a multi-national endeavor appears appropriate. Actions are underway or contemplated which should be capable of identifying and rectifying problem areas. The balance of this report presents 'Findings and Recommendations' (Section 2), 'Information in Support of Findings and Recommendations' (Section 3) and Appendices describing Panel membership, the NASA response to the March 1994 ASAP report, and a chronology of the panel's activities during the reporting period (Section 4).

  17. Safety First: Preventing Allergic Reactions

    ERIC Educational Resources Information Center

    Roy, Ken

    2015-01-01

    All elementary teachers should be aware of their students' allergies especially when they are planning to use plants or animals in the classroom or interacting with them in the field. This knowledge is essential because allergy symptoms can range from an itchy rash to anaphylactic shock. This column shares safety information for the science…

  18. Selected Problems in Sports Safety.

    ERIC Educational Resources Information Center

    American Alliance for Health, Physical Education, and Recreation, Washington, DC.

    This publication, covering a broad spectrum of sports safety problems, is designed as a source of information for those who plan, organize, administer, or evaluate various physical education and recreational activities, athletics, or sports. In the first section, the prevention of sports injury is stressed with attention to different age groups…

  19. Nation, Districts Step up Safety

    ERIC Educational Resources Information Center

    Shah, Nirvi

    2013-01-01

    President Barack Obama's announcement last week of a wide-ranging anti-violence plan in response to the Newtown, Connecticut, school shootings comes as many districts are adopting new and sometimes dramatic measures--including arming teachers and volunteers--intended to prevent similar tragedies in their own schools. School safety experts warn…

  20. Annual Safety Education Review 1972.

    ERIC Educational Resources Information Center

    American Association for Health, Physical Education, and Recreation, Washington, DC.

    This booklet presents articles completed in 1972 by the Division of Safety Education of the American Association for Health, Physical Education, and Recreation. The introductory article contains the accomplishments of the division in 1971-72. The major points covered are planning conferences, conventions and meetings; revising the operating code…

  1. Earthquake Safety: Activities for Children.

    ERIC Educational Resources Information Center

    Federal Emergency Management Agency, Washington, DC.

    Lessons on earthquake safety involving planning, preparation, and practice are presented in this booklet for teachers. Included are classroom activities designed for K-6 students, teaching notes, "Learning Links" that summarize interdisciplinary connections, a set of 15 masters for reproducing transparencies, handouts, and worksheets. Part 1 shows…

  2. Glue Guns: Aiming for Safety

    ERIC Educational Resources Information Center

    Roy, Ken

    2010-01-01

    While glue guns are very useful, there are safety issues. Regardless of the temperature setting, glue guns can burn skin. The teacher should demonstrate and supervise the use of glue guns and have a plan should a student get burned. There should be an initial first aid protocol in place, followed by a visit to the school nurse. An accident report…

  3. Schoolyard Ponds: Safety and Liability.

    ERIC Educational Resources Information Center

    Danks, Sharon Gamson

    2001-01-01

    Engaging, attractive schoolyard ponds provide habitat for wildlife and hold great educational promise. Reviews water safety and liability issues including mud, stagnant pond water that serves as mosquito breeding grounds, and drowning. Offers ideas for creatively addressing those issues through site planning, shallow water depth, signage and…

  4. Bloodborne Pathogens Exposure Control Plan.

    ERIC Educational Resources Information Center

    National Child Care Association, Atlanta, GA.

    This sample exposure control plan is a guide to assist child care providers in complying with the blood-borne pathogens standard issued by the Occupational Safety and Health Administration (OSHA). The standard requires employers to establish a written exposure control plan by May 5, 1992 (for exposure to microorganisms in human blood that cause…

  5. IMPORTANCE OF SAFETY CULTURE ASSESSMENT

    SciTech Connect

    Spitalnik, J.

    2004-10-06

    Safety Management has lately been considered by some Nuclear Regulatory agencies as the tool on which to concentrate their efforts to implement modern regulation structures, because Safety Culture was said to be difficult to monitor. However, Safety Culture can be assessed and monitored even if it is problematical to make Safety Culture the object of regulation. This paper stresses the feasibility and importance of Safety Culture Assessment based on self-assessment applications performed in several nuclear organizations in Latin America. Reasons and ownership for assessing Safety Culture are discussed, and relevant aspects considered for setting up and programming such an assessment are shown. Basic principles that were taken into account, as well as financial and human resources used in actual self-assessments are reviewed, including the importance of adequate statistical analyses and the necessity of proper feed-back of results. The setting up of action plans to enhance Safety Culture is the final step of the assessment program that once implemented will enable to establish a Safety Culture monitoring process within the organization.

  6. New Jersey Industrial Arts Education Safety Guide.

    ERIC Educational Resources Information Center

    Kobylarz, Joseph D.; Olender, Francis B.

    This guide was developed to assist the teacher in planning, implementing, revising, or improving safety instruction in industrial arts classes in New Jersey, and has as its theme, "Safety Is Everyone's Responsibility." The guide is organized in seven major sections. The first section explains the purpose of the guide, outlines the contents of a…

  7. Good Practices Guide for Bicycle Safety Education.

    ERIC Educational Resources Information Center

    Department of Transportation, Washington, DC.

    The purpose of this guide is to serve as an informational resource for educators and other interested professionals in planning and developing bicycle safety education programs. The guide examines 15 existing bicycle safety education programs in the United States and one from Canada. (Author)

  8. Private Schools Put Spotlight on Safety

    ERIC Educational Resources Information Center

    Zehr, Mary Ann

    2005-01-01

    Administrators and students at private schools tend to see their schools as safer than public schools. Spurred in part by the terrorist attacks of Sept. 11, 2001, many private schools have joined the national push to revamp campus safety plans. Kenneth S. Trump, the president of the Cleveland-based National School Safety and Security Services,…

  9. Some views on nuclear reactor safety

    SciTech Connect

    Tanguy, P.Y.

    1995-04-01

    This document is the text of a speech given by Pierre Y. Tanguy (Electricite de France) at the 22nd Water Reactor Safety Meeting held in Bethesda, MD in 1994. He describes the EDF nuclear program in broad terms and proceeds to discuss operational safety results with EDF plants. The speaker also outlines actions to enhance safety planned for the future, and he briefly mentions French cooperation with the Chinese on the Daya Bay project.

  10. First Aid and Safety

    MedlinePlus

    ... First-Aid Kit Food Safety for Your Family Gun Safety Halloween Candy Hints Household Safety Checklists Household ... Climbing, and Grabbing Household Safety: Preventing Injuries From Firearms Household Safety: Preventing Injuries in the Crib Household ...

  11. Nuclear safety policy working group recommendations on nuclear propulsion safety for the space exploration initiative

    NASA Technical Reports Server (NTRS)

    Marshall, Albert C.; Lee, James H.; Mcculloch, William H.; Sawyer, J. Charles, Jr.; Bari, Robert A.; Cullingford, Hatice S.; Hardy, Alva C.; Niederauer, George F.; Remp, Kerry; Rice, John W.

    1993-01-01

    An interagency Nuclear Safety Working Group (NSPWG) was chartered to recommend nuclear safety policy, requirements, and guidelines for the Space Exploration Initiative (SEI) nuclear propulsion program. These recommendations, which are contained in this report, should facilitate the implementation of mission planning and conceptual design studies. The NSPWG has recommended a top-level policy to provide the guiding principles for the development and implementation of the SEI nuclear propulsion safety program. In addition, the NSPWG has reviewed safety issues for nuclear propulsion and recommended top-level safety requirements and guidelines to address these issues. These recommendations should be useful for the development of the program's top-level requirements for safety functions (referred to as Safety Functional Requirements). The safety requirements and guidelines address the following topics: reactor start-up, inadvertent criticality, radiological release and exposure, disposal, entry, safeguards, risk/reliability, operational safety, ground testing, and other considerations.

  12. 30 CFR 75.161 - Plans for training programs.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Plans for training programs. 75.161 Section 75.161 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Qualified and Certified Persons § 75.161 Plans for training programs. Each operator...

  13. 30 CFR 75.161 - Plans for training programs.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Plans for training programs. 75.161 Section 75.161 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Qualified and Certified Persons § 75.161 Plans for training programs. Each operator...

  14. 30 CFR 75.161 - Plans for training programs.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Plans for training programs. 75.161 Section 75.161 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Qualified and Certified Persons § 75.161 Plans for training programs. Each operator...

  15. Online Safety.

    ERIC Educational Resources Information Center

    Levine, Elliott

    2001-01-01

    Describes provisions of Children's Internet Protection Act, which school districts are required to implement on or before October 31, 2001, involving the development and public dissemination of federally mandated Internet-safety policy to prevent minors from accessing inappropriate and harmful material. Provides suggestions to protect children…

  16. Playground Safety.

    ERIC Educational Resources Information Center

    Sipes, James L.

    2000-01-01

    Discusses the issues of risk, liability, and fun when landscaping playgrounds with safety in mind. The importance of playground surfaces and several preventive measures landscapers can use to reduce the risk of injury are discussed. Concluding comments address playground design features and liability. (GR)

  17. School Safety.

    ERIC Educational Resources Information Center

    The Newsletter of the Comprehensive Center-Region VI, 1999

    1999-01-01

    The articles in this issue dealing with school safety discusses what rural and small urban settings are doing to prevent violence and to educate young people about prosocial alternatives to violence. The research is quite clear that female, minority, and gay students are the targets of a disproportionate amount of harassment and violence, both in…

  18. Safety First!

    ERIC Educational Resources Information Center

    Longfield, Judith

    2006-01-01

    In this article, the author relates how a hands-on chemistry investigation provided her the inspiration to develop an effective safety lesson for her third grade chemistry class. She began the lesson by demonstrating the use of pH indicator paper to show that ordinary household (white) vinegar was an acid. With the students, she wondered aloud…

  19. Art Safety.

    ERIC Educational Resources Information Center

    BCATA Journal for Art Teachers, 1991

    1991-01-01

    Advocating that Canadian art programs should use and model environmentally safe practices, the articles in this journal focus on issues of safe practices in art education. Articles are: (1) "What is WHMIS?"; (2) "Safety Precautions for Specific Art Processes"; (3) "Toxic Substances"; (4) "Using Clay, Glazes, and Kilns Safely in the Classroom"…

  20. Safer Systems: A NextGen Aviation Safety Strategic Goal

    NASA Technical Reports Server (NTRS)

    Darr, Stephen T.; Ricks, Wendell R.; Lemos, Katherine A.

    2008-01-01

    The Joint Planning and Development Office (JPDO), is charged by Congress with developing the concepts and plans for the Next Generation Air Transportation System (NextGen). The National Aviation Safety Strategic Plan (NASSP), developed by the Safety Working Group of the JPDO, focuses on establishing the goals, objectives, and strategies needed to realize the safety objectives of the NextGen Integrated Plan. The three goal areas of the NASSP are Safer Practices, Safer Systems, and Safer Worldwide. Safer Practices emphasizes an integrated, systematic approach to safety risk management through implementation of formalized Safety Management Systems (SMS) that incorporate safety data analysis processes, and the enhancement of methods for ensuring safety is an inherent characteristic of NextGen. Safer Systems emphasizes implementation of safety-enhancing technologies, which will improve safety for human-centered interfaces and enhance the safety of airborne and ground-based systems. Safer Worldwide encourages coordinating the adoption of the safer practices and safer systems technologies, policies and procedures worldwide, such that the maximum level of safety is achieved across air transportation system boundaries. This paper introduces the NASSP and its development, and focuses on the Safer Systems elements of the NASSP, which incorporates three objectives for NextGen systems: 1) provide risk reducing system interfaces, 2) provide safety enhancements for airborne systems, and 3) provide safety enhancements for ground-based systems. The goal of this paper is to expose avionics and air traffic management system developers to NASSP objectives and Safer Systems strategies.

  1. [Remote radiation planning support system].

    PubMed

    Atsumi, Kazushige; Nakamura, Katsumasa; Yoshidome, Satoshi; Shioyama, Yoshiyuki; Sasaki, Tomonari; Ohga, Saiji; Yoshitake, Tadamasa; Shinoto, Makoto; Asai, Kaori; Sakamoto, Katsumi; Hirakawa, Masakazu; Honda, Hiroshi

    2012-08-01

    We constructed a remote radiation planning support system between Kyushu University Hospital (KUH) in Fukuoka and Kyushu University Beppu Hospital (KBH) in Oita. Between two institutions, radiology information system for radiotherapy division (RT-RIS) and radiation planning system (RTPS) were connected by virtual private network (VPN). This system enables the radiation oncologists at KUH to perform radiotherapy planning for the patients at KBH. The detail of the remote radiation planning support system in our institutions is as follows: The radiation oncologist at KBH performs radiotherapy planning and the data of the patients are sent anonymously to the radiation oncologists at KUH. The radiation oncologists at KUH receive the patient's data, access to RTPS at KBH, verify or change the radiation planning at KBH: Radiation therapy is performed at KBH according to the confirmed plan by the radiation oncologists at KUH. Our remote radiation planning system is useful for providing radiation therapy with safety and accuracy.

  2. 49 CFR 194.101 - Operators required to submit plans.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... Section 194.101 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY RESPONSE PLANS FOR ONSHORE OIL PIPELINES Response Plans § 194.101 Operators required to submit plans. (a)...

  3. 49 CFR 194.101 - Operators required to submit plans.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Section 194.101 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY RESPONSE PLANS FOR ONSHORE OIL PIPELINES Response Plans § 194.101 Operators required to submit plans. (a)...

  4. 49 CFR 194.101 - Operators required to submit plans.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... Section 194.101 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY RESPONSE PLANS FOR ONSHORE OIL PIPELINES Response Plans § 194.101 Operators required to submit plans. (a)...

  5. 49 CFR 194.101 - Operators required to submit plans.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... Section 194.101 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY RESPONSE PLANS FOR ONSHORE OIL PIPELINES Response Plans § 194.101 Operators required to submit plans. (a)...

  6. 49 CFR 194.109 - Submission of state response plans.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... Section 194.109 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY RESPONSE PLANS FOR ONSHORE OIL PIPELINES Response Plans § 194.109 Submission of state response plans. (a) In...

  7. 49 CFR 194.109 - Submission of state response plans.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... Section 194.109 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY RESPONSE PLANS FOR ONSHORE OIL PIPELINES Response Plans § 194.109 Submission of state response plans. (a) In...

  8. 49 CFR 194.109 - Submission of state response plans.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... Section 194.109 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY RESPONSE PLANS FOR ONSHORE OIL PIPELINES Response Plans § 194.109 Submission of state response plans. (a) In...

  9. 49 CFR 194.109 - Submission of state response plans.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... Section 194.109 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY RESPONSE PLANS FOR ONSHORE OIL PIPELINES Response Plans § 194.109 Submission of state response plans. (a) In...

  10. 49 CFR 194.109 - Submission of state response plans.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Section 194.109 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY RESPONSE PLANS FOR ONSHORE OIL PIPELINES Response Plans § 194.109 Submission of state response plans. (a) In...

  11. 10 CFR 76.91 - Emergency planning.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 10 Energy 2 2012-01-01 2012-01-01 false Emergency planning. 76.91 Section 76.91 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.91 Emergency planning. The Corporation shall establish, maintain, and be prepared to follow a written emergency plan....

  12. 10 CFR 76.91 - Emergency planning.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 10 Energy 2 2013-01-01 2013-01-01 false Emergency planning. 76.91 Section 76.91 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.91 Emergency planning. The Corporation shall establish, maintain, and be prepared to follow a written emergency plan....

  13. 10 CFR 76.91 - Emergency planning.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 10 Energy 2 2011-01-01 2011-01-01 false Emergency planning. 76.91 Section 76.91 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.91 Emergency planning. The Corporation shall establish, maintain, and be prepared to follow a written emergency plan....

  14. 10 CFR 76.91 - Emergency planning.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Emergency planning. 76.91 Section 76.91 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.91 Emergency planning. The Corporation shall establish, maintain, and be prepared to follow a written emergency plan....

  15. 10 CFR 76.91 - Emergency planning.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 10 Energy 2 2014-01-01 2014-01-01 false Emergency planning. 76.91 Section 76.91 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.91 Emergency planning. The Corporation shall establish, maintain, and be prepared to follow a written emergency plan....

  16. 10 CFR 820.65 - Implementation plan.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 4 2010-01-01 2010-01-01 false Implementation plan. 820.65 Section 820.65 Energy... plan. With respect to a DOE Nuclear Safety Requirement for which there is no regulatory provision for an implementation plan or schedule, an exemption may be granted to establish an implementation...

  17. 10 CFR 820.65 - Implementation plan.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 10 Energy 4 2011-01-01 2011-01-01 false Implementation plan. 820.65 Section 820.65 Energy DEPARTMENT OF ENERGY PROCEDURAL RULES FOR DOE NUCLEAR ACTIVITIES Exemption Relief § 820.65 Implementation plan. With respect to a DOE Nuclear Safety Requirement for which there is no regulatory provision for an implementation plan or schedule, an...

  18. 10 CFR 820.65 - Implementation plan.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 10 Energy 4 2014-01-01 2014-01-01 false Implementation plan. 820.65 Section 820.65 Energy... plan. With respect to a DOE Nuclear Safety Requirement for which there is no regulatory provision for an implementation plan or schedule, an exemption may be granted to establish an implementation...

  19. 49 CFR 192.615 - Emergency plans.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Emergency plans. 192.615 Section 192.615... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Operations § 192.615 Emergency plans. (a) Each operator... notifies the officials; and (4) Plan how the operator and officials can engage in mutual assistance...

  20. 14 CFR 431.41 - Communications plan.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 4 2011-01-01 2011-01-01 false Communications plan. 431.41 Section 431.41... Launch and Reentry of a Reusable Launch Vehicle § 431.41 Communications plan. (a) An applicant shall submit a plan providing vehicle safety operations personnel communications procedures during the...

  1. 14 CFR 431.41 - Communications plan.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Communications plan. 431.41 Section 431.41... Launch and Reentry of a Reusable Launch Vehicle § 431.41 Communications plan. (a) An applicant shall submit a plan providing vehicle safety operations personnel communications procedures during the...

  2. 10 CFR 820.65 - Implementation plan.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 10 Energy 4 2012-01-01 2012-01-01 false Implementation plan. 820.65 Section 820.65 Energy... plan. With respect to a DOE Nuclear Safety Requirement for which there is no regulatory provision for an implementation plan or schedule, an exemption may be granted to establish an implementation...

  3. Safety harness

    DOEpatents

    Gunter, Larry W.

    1993-01-01

    A safety harness to be worn by a worker, especially a worker wearing a plastic suit thereunder for protection in a radioactive or chemically hostile environment, which safety harness comprises a torso surrounding portion with at least one horizontal strap for adjustably securing the harness about the torso, two vertical shoulder straps with rings just forward of the of the peak of the shoulders for attaching a life-line and a pair of adjustable leg supporting straps releasibly attachable to the torso surrounding portion. In the event of a fall, the weight of the worker, when his fall is broken and he is suspended from the rings with his body angled slightly back and chest up, will be borne by the portion of the leg straps behind his buttocks rather than between his legs. Furthermore, the supporting straps do not restrict the air supplied through hoses into his suit when so suspended.

  4. Ferrocyanide Safety Program rationale for removing six tanks from the safety watch list

    SciTech Connect

    Borsheim, G.L.

    1993-09-01

    This report documents an in-depth study of single-shell tanks containing ferrocyanide wastes. Topics include: safety assessments, tank histories, supportive documentation about interim stabilization and planned remedial activities.

  5. Safety valve

    DOEpatents

    Bergman, Ulf C.

    1984-01-01

    The safety valve contains a resilient gland to be held between a valve seat and a valve member and is secured to the valve member by a sleeve surrounding the end of the valve member adjacent to the valve seat. The sleeve is movable relative to the valve member through a limited axial distance and a gap exists between said valve member and said sleeve.

  6. 2006 NASA Range Safety Annual Report

    NASA Technical Reports Server (NTRS)

    TenHaken, Ron; Daniels, B.; Becker, M.; Barnes, Zack; Donovan, Shawn; Manley, Brenda

    2007-01-01

    Throughout 2006, Range Safety was involved in a number of exciting and challenging activities and events, from developing, implementing, and supporting Range Safety policies and procedures-such as the Space Shuttle Launch and Landing Plans, the Range Safety Variance Process, and the Expendable Launch Vehicle Safety Program procedures-to evaluating new technologies. Range Safety training development is almost complete with the last course scheduled to go on line in mid-2007. Range Safety representatives took part in a number of panels and councils, including the newly formed Launch Constellation Range Safety Panel, the Range Commanders Council and its subgroups, the Space Shuttle Range Safety Panel, and the unmanned aircraft systems working group. Space based range safety demonstration and certification (formerly STARS) and the autonomous flight safety system were successfully tested. The enhanced flight termination system will be tested in early 2007 and the joint advanced range safety system mission analysis software tool is nearing operational status. New technologies being evaluated included a processor for real-time compensation in long range imaging, automated range surveillance using radio interferometry, and a space based range command and telemetry processor. Next year holds great promise as we continue ensuring safety while pursuing our quest beyond the Moon to Mars.

  7. CONVEYOR SYSTEM SAFETY ANALYSIS

    SciTech Connect

    M. Salem

    1995-06-23

    The purpose and objective of this analysis is to systematically identify and evaluate hazards related to the Yucca Mountain Project Exploratory Studies Facility (ESF) surface and subsurface conveyor system (for a list of conveyor subsystems see section 3). This process is an integral part of the systems engineering process; whereby safety is considered during planning, design, testing, and construction. A largely qualitative approach was used since a radiological System Safety Analysis is not required. The risk assessment in this analysis characterizes the accident scenarios associated with the conveyor structures/systems/components in terms of relative risk and includes recommendations for mitigating all identified risks. The priority for recommending and implementing mitigation control features is: (1) Incorporate measures to reduce risks and hazards into the structure/system/component (S/S/C) design, (2) add safety devices and capabilities to the designs that reduce risk, (3) provide devices that detect and warn personnel of hazardous conditions, and (4) develop procedures and conduct training to increase worker awareness of potential hazards, on methods to reduce exposure to hazards, and on the actions required to avoid accidents or correct hazardous conditions. The scope of this analysis is limited to the hazards related to the design of conveyor structures/systems/components (S/S/Cs) that occur during normal operation. Hazards occurring during assembly, test and maintenance or ''off normal'' operations have not been included in this analysis. Construction related work activities are specifically excluded per DOE Order 5481.1B section 4. c.

  8. Spill Safety

    ERIC Educational Resources Information Center

    Roy, Ken

    2005-01-01

    This article describes OSHA procedures for handling Occupational Exposure to Hazardous Chemicals in Laboratories. The Laboratory Standard requires a Chemical Hygiene Plan to address all aspects of working with hazardous chemicals. This includes dealing with chemical spills. Chemical spill kits or "spill crash carts" need to be available in case…

  9. 47 CFR 80.1135 - Transmission of maritime safety information.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 47 Telecommunication 5 2011-10-01 2011-10-01 false Transmission of maritime safety information. 80...) Operating Procedures for Distress and Safety Communications § 80.1135 Transmission of maritime safety... and the IMO Master Plan of Shore-Based Facilities. (b) The mode and format of the...

  10. 47 CFR 80.1135 - Transmission of maritime safety information.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 47 Telecommunication 5 2013-10-01 2013-10-01 false Transmission of maritime safety information. 80...) Operating Procedures for Distress and Safety Communications § 80.1135 Transmission of maritime safety... and the IMO Master Plan of Shore-Based Facilities. (b) The mode and format of the...

  11. 47 CFR 80.1135 - Transmission of maritime safety information.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 47 Telecommunication 5 2014-10-01 2014-10-01 false Transmission of maritime safety information. 80...) Operating Procedures for Distress and Safety Communications § 80.1135 Transmission of maritime safety... and the IMO Master Plan of Shore-Based Facilities. (b) The mode and format of the...

  12. 47 CFR 80.1135 - Transmission of maritime safety information.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 47 Telecommunication 5 2010-10-01 2010-10-01 false Transmission of maritime safety information. 80...) Operating Procedures for Distress and Safety Communications § 80.1135 Transmission of maritime safety... and the IMO Master Plan of Shore-Based Facilities. (b) The mode and format of the...

  13. A matrix safety frame approach to robot safety for space applications. Thesis

    NASA Technical Reports Server (NTRS)

    Montgomery, T. D.; Lauderbaugh, L. Ken

    1988-01-01

    The planned use of autonomous robots in space applications has generated many new safety problems. This thesis assesses safety of autonomous robot systems through the structure of a proposed three-dimensional matrix safety frame. By identifying the common points of accidents and fatalities involving terrestrial robots, reviewing terrestrial robot safety standards, and modifying and extending these results to space applications, hazards are identified and their associated risks assessed. Three components of the safeguarding dimension of the matrix safety frame, safeguarding through design and operation for intrinsic safety, and incorporation of add-on safety systems are explained through examples for both terrestrial and space robots. A space robot hazard identification checklist, a qualitative tool for robot systems designers, is developed using the structure imparted by the matrix safety frame. The development of an expert system from the contents of the checklist is discussed.

  14. 49 CFR 194.111 - Response plan retention.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY RESPONSE PLANS FOR ONSHORE OIL PIPELINES... conducted, for example, in field offices, supervisors' vehicles, or spill response trailers. (b)...

  15. 49 CFR 194.111 - Response plan retention.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY RESPONSE PLANS FOR ONSHORE OIL PIPELINES... conducted, for example, in field offices, supervisors' vehicles, or spill response trailers. (b)...

  16. 49 CFR 194.111 - Response plan retention.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY RESPONSE PLANS FOR ONSHORE OIL PIPELINES... conducted, for example, in field offices, supervisors' vehicles, or spill response trailers. (b)...

  17. 49 CFR 194.111 - Response plan retention.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY RESPONSE PLANS FOR ONSHORE OIL PIPELINES... conducted, for example, in field offices, supervisors' vehicles, or spill response trailers. (b)...

  18. 49 CFR 194.111 - Response plan retention.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY RESPONSE PLANS FOR ONSHORE OIL PIPELINES... conducted, for example, in field offices, supervisors' vehicles, or spill response trailers. (b)...

  19. Language Planning: Corpus Planning.

    ERIC Educational Resources Information Center

    Baldauf, Richard B., Jr.

    1989-01-01

    Focuses on the historical and sociolinguistic studies that illuminate corpus planning processes. These processes are broken down and discussed under two categories: those related to the establishment of norms, referred to as codification, and those related to the extension of the linguistic functions of language, referred to as elaboration. (60…

  20. 77 FR 55224 - Notice of Availability of the Proposed Imperial Sand Dunes Recreation Area Management Plan and...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-09-07

    ... soils; mineral resources; socioeconomics; public health and safety; and visual resources. The Proposed... Management Plan and California Desert Conservation Area Plan Amendment/Final Environmental Impact Statement... Management Plan (RAMP) and California Desert Conservation Area (CDCA) Plan Amendment/Final...

  1. 78 FR 5717 - Safety Zone; Military Ocean Terminal Concord Safety Zone, Suisun Bay, Military Ocean Terminal...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-01-28

    ... DHS Department of Homeland Security FR Federal Register MOTCO Military Ocean Terminal Concord NPRM..., 2008, issue of the Federal Register (73 FR 3316). 4. Public Meeting We do not now plan to hold a public... SECURITY Coast Guard 33 CFR Part 165 RIN 1625-AA00 Safety Zone; Military Ocean Terminal Concord Safety...

  2. Safety and Liability.

    ERIC Educational Resources Information Center

    Berthelot, Ronald J.; And Others

    1982-01-01

    This series of five articles highlights Pensacola Junior College's occupational safety course, involving simulated emergencies, Florida's standards for teacher liability, electrical safety in the classroom and laboratory, color coding for machine safety, and Florida industrial arts safety instructional materials. (SK)

  3. A Product Safety Primer

    ERIC Educational Resources Information Center

    Brown, Mary Anne Symons

    1975-01-01

    The article offers an overview of the product safety issue and offers ideas for helping students develop product safety awareness. The role of the Consumer Product Safety Commission and safety legislation are discussed. (MW)

  4. NIF Title III engineering plan

    SciTech Connect

    Deis, G

    1998-06-01

    The purpose of this document is to define the work that must be accomplished by the NIF Project during Title III Engineering. This definition is intended to be sufficiently detailed to provide a framework for yearly planning, to clearly identify the specific deliverables so that the Project teams can focus on them, and to provide a common set of objectives and processes across the Project. This plan has been preceded by similar documents for Title I and Title II design and complements the Site Management Plan, the Project Control Manual, the Quality Assurance Program Plan, the RM Parsons NIF Title III Configuration Control Plan, the Integrated Project Schedule, the Preliminary Safety Analysis Report, the Configuration Management Plan, and the Transition Plan.

  5. Plutonium Vulnerability Management Plan

    SciTech Connect

    1995-03-01

    This Plutonium Vulnerability Management Plan describes the Department of Energy`s response to the vulnerabilities identified in the Plutonium Working Group Report which are a result of the cessation of nuclear weapons production. The responses contained in this document are only part of an overall, coordinated approach designed to enable the Department to accelerate conversion of all nuclear materials, including plutonium, to forms suitable for safe, interim storage. The overall actions being taken are discussed in detail in the Department`s Implementation Plan in response to the Defense Nuclear Facilities Safety Board (DNFSB) Recommendation 94-1. This is included as Attachment B.

  6. Safety Grooving

    NASA Technical Reports Server (NTRS)

    1985-01-01

    Safety grooving, the cutting of grooves in concrete to increase traction and prevent injury, was first developed to reduce aircraft accidents on wet runways. Represented by the International Grooving and Grinding Association (IG&GA), the industry expanded into highway and pedestrian applications. The technique originated at Langley, which assisted in testing the grooving at airports and on highways. Skidding was reduced, stopping distance decreased, and a vehicle's cornering ability on curves was increased. The process has been extended to animal holding pens, steps, parking lots and other potentially slippery surfaces.

  7. ES H action plan

    SciTech Connect

    Not Available

    1991-01-01

    This document contains planned actions to correct the deficiencies identified in the Pre-Tiger Team Self-Assessment (PTTSA), January 1991, of Sandia National Laboratories (SNL -- Albuquerque, New Mexico; Tonopah, Nevada; and Kauai, Hawaii). The Self-Assessment was conducted by a Self-Assessment Working Group consisting of 19 department managers, with support from Environment, Safety, and Health (ES H) professionals, from October through December 1990. Findings from other past audits, dating back to 1985, were reviewed and compared with the PTTSA findings to determine if additional findings, key findings, or root causes were warranted. The resulting ES H Action Plan and individual planned actions were prepared by the ES H Action Plan Project Group with assistance from the Program owners/authors during February and March 1991. The plan was reviewed by SNL Management in April 1991. This document serves as a planning instrument for the Laboratories to aid in the scoping and sizing of activities related to ES H compliance for the coming five years. It will be modified as required to ensure a workload/funding balance and to address the findings resulting from the Tiger Team assessment at SNL, Albuquerque. The process of producing this document has served well to prepare SNL, Albuquerque, for the coming task of producing the required post-Tiger Team action plan document. 8 tabs.

  8. 78 FR 4477 - Review of Safety Analysis Reports for Nuclear Power Plants, Introduction

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-01-22

    ... COMMISSION Review of Safety Analysis Reports for Nuclear Power Plants, Introduction AGENCY: Nuclear... subsection to NUREG-0800, ``Standard Review Plan for the Review of Safety Analysis Reports for Nuclear Power..., Standard Review Plan for the Review of Safety Analysis Reports for Nuclear Power Plants:...

  9. 14 CFR 437.41 - Mishap response plan.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... TRANSPORTATION LICENSING EXPERIMENTAL PERMITS Requirements to Obtain an Experimental Permit Operational Safety Documentation § 437.41 Mishap response plan. An applicant must provide a mishap response plan that meets...

  10. 14 CFR 437.41 - Mishap response plan.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... TRANSPORTATION LICENSING EXPERIMENTAL PERMITS Requirements to Obtain an Experimental Permit Operational Safety Documentation § 437.41 Mishap response plan. An applicant must provide a mishap response plan that meets...

  11. 49 CFR 234.201 - Location of plans.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ..., DEPARTMENT OF TRANSPORTATION GRADE CROSSING SIGNAL SYSTEM SAFETY AND STATE ACTION PLANS Maintenance... maintenance and testing shall be kept at each highway-rail grade crossing warning system location. Plans...

  12. 49 CFR 234.201 - Location of plans.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ..., DEPARTMENT OF TRANSPORTATION GRADE CROSSING SIGNAL SYSTEM SAFETY AND STATE ACTION PLANS Maintenance... maintenance and testing shall be kept at each highway-rail grade crossing warning system location. Plans...

  13. The Importance of Having an Effective School Crisis Response Plan.

    ERIC Educational Resources Information Center

    Watson, James A.

    2000-01-01

    Details the components of a public school safety plan and how to develop a crisis response plan with emergency responders. The importance of crisis response team members knowing their roles and being held accountable are stressed. (GR)

  14. A system safety model for developmental aircraft programs

    NASA Technical Reports Server (NTRS)

    Amberboy, E. J.; Stokeld, R. L.

    1982-01-01

    Basic tenets of safety as applied to developmental aircraft programs are presented. The integration of safety into the project management aspects of planning, organizing, directing and controlling is illustrated by examples. The basis for project management use of safety and the relationship of these management functions to 'real-world' situations is presented. The rationale which led to the safety-related project decision and the lessons learned as they may apply to future projects are presented.

  15. Super Safety and Health Day at KSC

    NASA Technical Reports Server (NTRS)

    2000-01-01

    Employees gather around a demonstration by Florida Power and Light during Super Safety and Health Day at KSC. Safety Day is a full day of NASA-sponsored, KSC and 45th Space Wing events involving a number of health- and safety-related activities: Displays, vendors, technical paper sessions, panel discussions, a keynote speaker, etc. The entire Center and Wing stand down to participate in the planned events. Safety Day is held annually to proactively increase awareness in safety and health among the government and contractor workforce population. The first guiding principle at KSC is '''Safety and Health First.''' KSC's number one goal is to '''Assure sound, safe and efficient practices and processes are in place for privatized/commercialized launch site processing.'''

  16. Microbiological Food Safety Surveillance in China.

    PubMed

    Pei, Xiaoyan; Li, Ning; Guo, Yunchang; Liu, Xiumei; Yan, Lin; Li, Ying; Yang, Shuran; Hu, Jing; Zhu, Jianghui; Yang, Dajin

    2015-09-01

    Microbiological food safety surveillance is a system that collects data regarding food contamination by foodborne pathogens, parasites, viruses, and other harmful microbiological factors. It helps to understand the spectrum of food safety, timely detect food safety hazards, and provide relevant data for food safety supervision, risk assessment, and standards-setting. The study discusses the microbiological surveillance of food safety in China, and introduces the policies and history of the national microbiological surveillance system. In addition, the function and duties of different organizations and institutions are provided in this work, as well as the generation and content of the surveillance plan, quality control, database, and achievement of the microbiological surveillance of food safety in China.

  17. Super Safety and Health Day at KSC

    NASA Technical Reports Server (NTRS)

    2000-01-01

    -- In the Training Auditorium at KSC, Center Director Roy Bridges addresses attendees at a presentation for Super Safety and Health Day. Safety Day is a full day of NASA-sponsored, KSC and 45th Space Wing events involving a number of health and safety related activities: Displays, vendors, technical paper sessions, panel discussions, a keynote speaker, etc. The entire Center and Wing stand down to participate in the planned events. Safety Day is held annually to proactively increase awareness in safety and health among the government and contractor workforce population. The first guiding principle at KSC is '''Safety and Health First.''' KSC's number one goal is to '''Assure sound, safe and efficient practices and processes are in place for privatized/commercialized launch site processing.'''

  18. Super Safety and Health Day at KSC

    NASA Technical Reports Server (NTRS)

    2000-01-01

    During Super Safety and Health Day at KSC, keynote speaker Dr. Beck Weathers is given a memento of his visit by Center Director Roy Bridges. Weathers spoke about his ordeal of surviving the 1996 Mt. Everest disaster and the lessons learned from the experience. Safety Day is a full day of NASA-sponsored, KSC and 45th Space Wing events involving a number of health and safety related activities: Displays, vendors, technical paper sessions, panel discussions, a keynote speaker, etc. The entire Center and Wing stand down to participate in the planned events. Safety Day is held annually to proactively increase awareness in safety and health among the government and contractor workforce population. The first guiding principle at KSC is '''Safety and Health First.''' KSC's number one goal is to '''Assure sound, safe and efficient practices and processes are in place for privatized/commercialized launch site processing.'''

  19. Super Safety and Health Day at KSC

    NASA Technical Reports Server (NTRS)

    2000-01-01

    During Super Safety and Health Day at KSC, keynote speaker Dr. Beck Weathers grimaces over the satellite photo of Mt. Everest being presented by Center Director Roy Bridges. Weathers spoke about his ordeal of surviving the 1996 Mt. Everest disaster and the lessons learned from the experience. Safety Day is a full day of NASA-sponsored, KSC and 45th Space Wing events involving a number of health and safety related activities: Displays, vendors, technical paper sessions, panel discussions, a keynote speaker, etc. The entire Center and Wing stand down to participate in the planned events. Safety Day is held annually to proactively increase awareness in safety and health among the government and contractor workforce population. The first guiding principle at KSC is '''Safety and Health First.''' KSC's number one goal is to '''Assure sound, safe and efficient practices and processes are in place for privatized/commercialized launch site processing.'''

  20. Super Safety and Health Day at KSC

    NASA Technical Reports Server (NTRS)

    2000-01-01

    Center Director Roy Bridges talks to workers outside the Hazardous Maintenance Facility during Super Safety and Health Day at KSC. Safety Day is a full day of NASA-sponsored, KSC and 45th Space Wing events involving a number of health and safety related activities: Displays, vendors, technical paper sessions, panel discussions, a keynote speaker, etc. The entire Center and Wing stand down to participate in the planned events. Safety Day is held annually to proactively increase awareness in safety and health among the government and contractor workforce population. The first guiding principle at KSC is '''Safety and Health First.''' KSC's number one goal is to '''Assure sound, safe and efficient practices and processes are in place for privatized/commercialized launch site processing.'''

  1. Microbiological Food Safety Surveillance in China

    PubMed Central

    Pei, Xiaoyan; Li, Ning; Guo, Yunchang; Liu, Xiumei; Yan, Lin; Li, Ying; Yang, Shuran; Hu, Jing; Zhu, Jianghui; Yang, Dajin

    2015-01-01

    Microbiological food safety surveillance is a system that collects data regarding food contamination by foodborne pathogens, parasites, viruses, and other harmful microbiological factors. It helps to understand the spectrum of food safety, timely detect food safety hazards, and provide relevant data for food safety supervision, risk assessment, and standards-setting. The study discusses the microbiological surveillance of food safety in China, and introduces the policies and history of the national microbiological surveillance system. In addition, the function and duties of different organizations and institutions are provided in this work, as well as the generation and content of the surveillance plan, quality control, database, and achievement of the microbiological surveillance of food safety in China. PMID:26343705

  2. Super Safety and Health Day at KSC

    NASA Technical Reports Server (NTRS)

    2000-01-01

    In an exhibit tent during Super Safety and Health Day at KSC, employees sample iced tea from a vendor. Safety Day is a full day of NASA-sponsored, KSC and 45th Space Wing events involving a number of health- and safety-related activities: Displays, vendors, technical paper sessions, panel discussions, a keynote speaker, etc. The entire Center and Wing stand down to participate in the planned events. Safety Day is held annually to proactively increase awareness in safety and health among the government and contractor workforce population. The first guiding principle at KSC is '''Safety and Health First.''' KSC's number one goal is to '''Assure sound, safe and efficient practices and processes are in place for privatized/commercialized launch site processing.'''

  3. Super Safety and Health Day at KSC

    NASA Technical Reports Server (NTRS)

    2000-01-01

    Vendor tents and displays filled the grounds in the Industrial Area as well as LC 39 Area during Super Safety and Health Day at KSC. Safety Day is a full day of NASA-sponsored, KSC and 45th Space Wing events involving a number of health and safety related activities: Displays, vendors, technical paper sessions, panel discussions, a keynote speaker, etc. The entire Center and Wing stand down to participate in the planned events. Safety Day is held annually to proactively increase awareness in safety and health among the government and contractor workforce population. The first guiding principle at KSC is '''Safety and Health First.''' KSC's number one goal is to '''Assure sound, safe and efficient practices and processes are in place for privatized/commercialized launch site processing.'''

  4. Radiation Safety among Workers in Health Services.

    PubMed

    Jones, Eric; Mathieson, Kathleen

    2016-05-01

    The purpose of this study was to survey health service workers regarding their radiation safety knowledge and practice. Participants were health service workers (n = 721) who received an anonymous online survey by email to test their radiation safety knowledge. A knowledge test of 15 questions was completed by 412 respondents. The overall average percent correct was 77.9%. Health physicists/medical physicists had the highest average percent score (93.5%), while physician assistants scored the lowest (60.0%). Of all the respondents, only 64.0% reported they participated in periodic radiation safety training at their place of employment. The most common topic selected where participants wanted additional training was in biological effects of radiation (41.0%). In conclusion, radiation safety training and education needs to be developed and planned effectively. Areas or specialties with poor radiation safety knowledge need to be addressed with corresponding safety measures. PMID:27023151

  5. Are your employees sick of hearing about safety? Ways to improve how safety is communicated at your company

    SciTech Connect

    Pollari, Roger A.

    2008-06-02

    Companies that care about their employees care about their employees’ safety and will go to great lengths to communicate the importance of working safely. Monthly safety meetings, creative safety contests, safety websites, sharing lessons learned—safety communicators tend to use a variety of methods to distribute procedures and critical safety information to help employees plan and perform work. However, the safety message falls on deaf ears in some cases, especially when employees feel they’re being overloaded with safety information to the point where they are sick of hearing about it. This poses a conundrum for safety communicators: Should they keep pouring on the safety, or should they lighten up? How much is the right amount?

  6. Can we improve patient safety?

    PubMed

    Corbally, Martin Thomas

    2014-01-01

    Despite greater awareness of patient safety issues especially in the operating room and the widespread implementation of surgical time out World Health Organization (WHO), errors, especially wrong site surgery, continue. Most such errors are due to lapses in communication where decision makers fail to consult or confirm operative findings but worryingly where parental concerns over the planned procedure are ignored or not followed through. The WHO Surgical Pause/Time Out aims to capture these errors and prevent them, but the combination of human error and complex hospital environments can overwhelm even robust safety structures and simple common sense. Parents are the ultimate repository of information on their child's condition and planned surgery but are traditionally excluded from the process of Surgical Pause and Time Out, perhaps to avoid additional stress. In addition, surgeons, like pilots, are subject to the phenomenon of "plan-continue-fail" with potentially disastrous outcomes. If we wish to improve patient safety during surgery and avoid wrong site errors then we must include parents in the Surgical Pause/Time Out. A recent pilot study has shown that neither staff nor parents found it added to their stress, but, moreover, 100% of parents considered that it should be a mandatory component of the Surgical Pause nor does it add to the stress of surgery. Surgeons should be required to confirm that the planned procedure is in keeping with the operative findings especially in extirpative surgery and this "step back" should be incorporated into the standard Surgical Pause. It is clear that we must improve patient safety further and these simple measures should add to that potential. PMID:25279366

  7. 75 FR 4794 - Draft Revised Strategic Plan for FY 2010-2015

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-01-29

    ... SAFETY BOARD Draft Revised Strategic Plan for FY 2010-2015 AGENCY: Defense Nuclear Facilities Safety... revised strategic plan. The Board will consider all comments received as a result of this outreach effort... plan will replace the Board's FY 2003-2009 Strategic Plan, dated November 17, 2003. Dated: January...

  8. NASA aviation safety reporting system

    NASA Technical Reports Server (NTRS)

    Billings, C. E.; Lauber, J. K.; Funkhouser, H.; Lyman, E. G.; Huff, E. M.

    1976-01-01

    The origins and development of the NASA Aviation Safety Reporting System (ASRS) are briefly reviewed. The results of the first quarter's activity are summarized and discussed. Examples are given of bulletins describing potential air safety hazards, and the disposition of these bulletins. During the first quarter of operation, the ASRS received 1464 reports; 1407 provided data relevant to air safety. All reports are being processed for entry into the ASRS data base. During the reporting period, 130 alert bulletins describing possible problems in the aviation system were generated and disseminated. Responses were received from FAA and others regarding 108 of the alert bulletins. Action was being taken with respect to 70 of the 108 responses received. Further studies are planned of a number of areas, including human factors problems related to automation of the ground and airborne portions of the national aviation system.

  9. A culture of safety: a business strategy for medical practices.

    PubMed

    Saxton, James W; Finkelstein, Maggie M; Marles, Adam F

    2012-01-01

    Physician practices can enhance their economics by taking patient safety to a new level within their practices. Patient safety has a lot to do with systems and processes that occur not only at the hospital but also within a physician's practice. Historically, patient safety measures have been hospital-focused and -driven, largely due to available resources; however, physician practices can impact patient safety, efficiently and effectively, with a methodical plan involving assessment, prioritization, and compliance. With the ever-increasing focus of reimbursement on quality and patient safety, physician practices that implement a true culture of safety now could see future economic benefits using this business strategy.

  10. A culture of safety: a business strategy for medical practices.

    PubMed

    Saxton, James W; Finkelstein, Maggie M; Marles, Adam F

    2012-01-01

    Physician practices can enhance their economics by taking patient safety to a new level within their practices. Patient safety has a lot to do with systems and processes that occur not only at the hospital but also within a physician's practice. Historically, patient safety measures have been hospital-focused and -driven, largely due to available resources; however, physician practices can impact patient safety, efficiently and effectively, with a methodical plan involving assessment, prioritization, and compliance. With the ever-increasing focus of reimbursement on quality and patient safety, physician practices that implement a true culture of safety now could see future economic benefits using this business strategy. PMID:22413601

  11. Managing safety in a research and development environment

    SciTech Connect

    Cummings, G.E.

    1995-12-22

    A method for managing safety in a research and development environment is described which involves both the subject matter experts and the researchers in development of safety policy and implementation planning. This method has been used effectively at LLNL to maximize safety benefits while minimizing the costs of the safety program and aggravation to the researcher. A product of this effort is the establishment of an effective safety culture as the line organizations work with the subject matter experts to develop and implement the safety program.

  12. Safety on Earth From MARSS

    NASA Technical Reports Server (NTRS)

    2002-01-01

    ENSCO, Inc., developed the Meteorological and Atmospheric Real-time Safety Support (MARSS) system for real-time assessment of meteorological data displays and toxic material spills. MARSS also provides mock scenarios to guide preparations for emergencies involving meteorological hazards and toxic substances. Developed under a Small Business Innovation Research (SBIR) contract with Kennedy Space Center, MARSS was designed to measure how safe NASA and Air Force range safety personnel are while performing weather sensitive operations around launch pads. The system augments a ground operations safety plan that limits certain work operations to very specific weather conditions. It also provides toxic hazard prediction models to assist safety managers in planning for and reacting to releases of hazardous materials. MARSS can be used in agricultural, industrial, and scientific applications that require weather forecasts and predictions of toxic smoke movement. MARSS is also designed to protect urban areas, seaports, rail facilities, and airports from airborne releases of hazardous chemical substances. The system can integrate with local facility protection units and provide instant threat detection and assessment data that is reportable for local and national distribution.

  13. [Safety in brachytherapy].

    PubMed

    Marcié, S; Marinello, G; Peiffert, D; Lartigau, É

    2013-04-01

    No technique can now be used without previously considering the safety of patients, staff and public and risk management. This is the case for brachytherapy. The various aspects of brachytherapy are discussed for both the patient and the staff. For all, the risks must be minimized while achieving a treatment of quality. It is therefore necessary to establish a list as comprehensive as possible regardless of the type of brachytherapy (low, high, pulsed dose-rate). Then, their importance must be assessed with the help of their criticality. Radiation protection of personnel and public must take into account the many existing regulation texts. Four axes have been defined for the risk management for patients: organization, preparation, planning and implementation of treatment. For each axis, a review of risks is presented, as well as administrative, technical and medical dispositions for staff and the public. PMID:23465784

  14. 23 CFR 450.214 - Development and content of the long-range statewide transportation plan.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... shall reference, summarize, or contain any applicable short-range planning studies; strategic planning... TRANSPORTATION PLANNING AND RESEARCH PLANNING ASSISTANCE AND STANDARDS Statewide Transportation Planning and..., countermeasures, or projects contained in the Strategic Highway Safety Plan required by 23 U.S.C. 148. (e)...

  15. 29 CFR 1952.120 - Description of the plan.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 29 Labor 9 2011-07-01 2011-07-01 false Description of the plan. 1952.120 Section 1952.120 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) APPROVED STATE PLANS FOR ENFORCEMENT OF STATE STANDARDS Washington § 1952.120 Description of the plan. (a)(1) The plan...

  16. Compliance plan for PG and E geysers unit 16

    SciTech Connect

    Not Available

    1981-03-01

    A plan is described to establish a monitoring system to assure that the geothermal power plant is constructed and operated in compliance with air and water quality, public health and safety, and other applicable regulations, guidelines, and conditions of the California Energy Commission. The plan is divided into: a Power Plant Compliance Plan and a Transmission Line Compliance Plan. (MHR)

  17. Elementary Physical Education Weekly Lesson Plan. Kindergarten.

    ERIC Educational Resources Information Center

    Anchorage Borough School District, AK.

    This curriculum guide is for the teaching of physical education to kindergarten students. Teaching procedures, warm-up activities, safety procedures, modifications, and athletic equipment needed are described for each of the specific activities in the weekly lesson plans. (CJ)

  18. Transportation Safety Excellence in Operations Through Improved Transportation Safety Document

    SciTech Connect

    Dr. Michael A. Lehto; MAL

    2007-05-01

    requirements with waste requirements. MFC’s efforts illustrate that utilizing the requirements of other disciplines, beyond nuclear safety, can provide an efficient process. Analyzing current processes to find better ways of meeting the requirements of multiple disciplines within a safety basis can lead to a more cost-effective, streamlined process. 2) Incorporating the DOT Type A drums into the MFC TSD was efficient because safety analysts utilized a transportation plan that provided analysis that could also be used for the change to the TSD addendum. In addition, because the plan they used had already been approved and was in use by the Idaho Cleanup Project (ICP) at the INL, justification for the change to the TSD was more compelling. MFC safety analysts proved that streamlining a process can be made more feasible by drawing from analysis that has already been completed.

  19. National Ignition Facility Project Site Safety Program

    SciTech Connect

    Moses, E

    2001-09-30

    This Safety Program for the National Ignition Facility (NIF) presents safety protocols and requirements that management and workers shall follow to assure a safe and healthful work environment during the construction, equipment installation, and commissioning activities. As the NIF Project transitions from a conventional facility construction activity to one of equipment installation, commissioning, initial laser operations, and other more routine-like operations, new safety requirements are needed. The NIF Project Site Safety Program (NPSSP) requires that all activities at the NIF Project site be performed in accordance with the ''LLNL ES&H Manual'', and the augmented set of controls and processes described in this NIF Project Site Safety Program. More specific requirements for construction activities under the Integration Management and Installation (IMI) contract are provided in the ''NIF Infrastructure Health and Safety Plan'', subtier to this program. Specifically this document: Defines the fundamental NIF site safety philosophy, Defines the areas covered by this safety program (see Appendix B), Identifies management roles and responsibilities, Defines core safety management processes, and Identifies NIF site-specific safety requirements.

  20. Aerospace Safety Advisory Panel

    NASA Technical Reports Server (NTRS)

    2001-01-01

    This annual report is based on the activities of the Aerospace Safety Advisory Panel in calendar year 2000. During this year, the construction of the International Space Station (ISS) moved into high gear. The launch of the Russian Service Module was followed by three Space Shuttle construction and logistics flights and the deployment of the Expedition One crew. Continuous habitation of the ISS has begun. To date, both the ISS and Space Shuttle programs have met or exceeded most of their flight objectives. In spite of the intensity of these efforts, it is clear that safety was always placed ahead of cost and schedule. This safety consciousness permitted the Panel to devote more of its efforts to examining the long-term picture. With ISS construction accelerating, demands on the Space Shuttle will increase. While Russian Soyuz and Progress spacecraft will make some flights, the Space Shuttle remains the primary vehicle to sustain the ISS and all other U.S. activities that require humans in space. Development of a next generation, human-rated vehicle has slowed due to a variety of technological problems and the absence of an approach that can accomplish the task significantly better than the Space Shuttle. Moreover, even if a viable design were currently available, the realities of funding and development cycles suggest that it would take many years to bring it to fruition. Thus, it is inescapable that for the foreseeable future the Space Shuttle will be the only human-rated vehicle available to the U.S. space program for support of the ISS and other missions requiring humans. Use of the Space Shuttle will extend well beyond current planning, and is likely to continue for the life of the ISS.