Comparison of streamflow and water-quality data collection techniques for the Saginaw River, Michigan

USGS Publications Warehouse

Hoard, C.J.; Holtschlag, D.J.; Duris, J.W.; James, D.A.; Obenauer, D.J.

2012-01-01

In 2009, the Michigan Department of Environmental Quality and the U.S. Geological Survey developed a plan to compare the effect of various streamgaging and water-quality collection techniques on streamflow and stream water-quality data for the Saginaw River, Michigan. The Saginaw River is the primary contributor of surface runoff to Saginaw Bay, Lake Huron, draining approximately 70 percent of the Saginaw Bay watershed. The U.S. Environmental Protection Agency has listed the Saginaw Bay system as an "Area of Concern" due to many factors, including excessive sediment and nutrient concentrations in the water. Current efforts to estimate loading of sediment and nutrients to Saginaw Bay utilize water-quality samples collected using a surface-grab technique and flow data that are uncertain during specific conditions. Comparisons of current flow and water-quality sampling techniques to alternative techniques were assessed between April 2009 and September 2009 at two locations in the Saginaw River. Streamflow estimated using acoustic Doppler current profiling technology was compared to a traditional stage-discharge technique. Complex conditions resulting from the influence of Saginaw Bay on the Saginaw River were able to be captured using the acoustic technology, while the traditional stage-discharge technique failed to quantify these effects. Water-quality samples were collected at two locations and on eight different dates, utilizing both surface-grab and depth-integrating multiple-vertical techniques. Sixteen paired samples were collected and analyzed for suspended sediment, turbidity, total phosphorus, total nitrogen, orthophosphate, nitrite, nitrate, and ammonia. Results indicate that concentrations of constituents associated with suspended material, such as suspended sediment, turbidity, and total phosphorus, are underestimated when samples are collected using the surface-grab technique. The median magnitude of the relative percent difference in concentration based

Non-Invasive Pneumothorax Detector Final Report CRADA No. TC02110.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chang, J. T.; Purcell, R.

This was a collaborative effort between Lawrence Livermore National Security, LLC as manager and operator of Lawrence Livermore National Laboratory (LLNL) and ElectroSonics Medical Inc. (formerly known as BIOMEC, Inc.), to develop a non-invasive pneumothorax detector based upon the micropower impulse radar technology invented at LLNL. Under a Work for Others Subcontract (L-9248), LLNL and ElectroSonics successfully demonstrated the feasibility of a novel device for non-invasive detection of pneumothorax for emergency and long-term monitoring. The device is based on Micropower Impulse Radar (MIR) Ultra Wideband (UWB) technology. Phase I experimental results were promising, showing that a pneumothorax volume even asmore » small as 30 ml was clearly detectable from the MIR signals. Phase I results contributed to the award of a National Institute of Health (NIH) SBIR Phase II grant to support further research and development. The Phase II award led to the establishment of a LLNL/ElectroSonics CRADA related to Case No. TC02045.0. Under the subsequent CRADA, LLNL and ElectroSonics successfully demonstrated the feasibility of the pneumothorax detection in human subject research trials. Under this current CRADA TC02110.0, also referred to as Phase II Type II, the project scope consisted of seven tasks in Project Year 1; five tasks in Project Year 2; and four tasks in Project Year 3. Year 1 tasks were aimed toward the delivery of the pneumothorax detector design package for the pre-production of the miniaturized CompactFlash dockable version of the system. The tasks in Project Years 2 and 3 critically depended upon the accomplishments of Task 1. Since LLNL’s task was to provide subject matter expertise and performance verification, much of the timeline of engagement by the LLNL staff depended upon the overall project milestones as determined by the lead organization ElectroSonics. The scope of efforts were subsequently adjusted accordingly to commensurate with funding

Nano-Filament Field Emission Cathode Development Final Report CRADA No. TSB-0731-93

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bernhardt, Tony; Fahlen, Ted

At the time the CRADA was established, Silicon Video Corporation, of Cupertino, CA was a one-year-old rapidly growing start-up company. SVC was developing flat panel displays (FPDs) to replace Cathode Ray Terminals (CRTs) for personal computers, work stations and televisions. They planned to base their products on low cost and energy efficient field emission technology. It was universally recognized that the display was both the dominant cost item and differentiating feature of many products such as laptop computers and hand-held electronics and that control of the display technology through U.S. sources was essential to success in these markets. The purposemore » of this CRADA project was to determine if electrochemical planarization would be a viable, inexpensive alternative to current optical polishing techniques for planarizing the surface of a ceramic backplate of a thin film display.« less

H2@Scale Laboratory CRADA Call | Hydrogen and Fuel Cells | NREL

Science.gov Websites

research and development agreement (CRADA) projects with the Hydrogen at Scale (H2@Scale) national CRADA Call H2@Scale CRADA Agreement Template Responses to CRADA Call Questions: Part 1 (includes

Genetic contribution of hatchery fish to walleye stocks in Saginaw Bay, Michigan

USGS Publications Warehouse

Todd, Thomas N.; Haas, Robert C.; Schramm, Harold L.; Piper, Robert G.

1995-01-01

Stocks of walleye (Stizostedion vitreum) were severely depressed in Saginaw Bay in the 1970s. In 1979, the Michigan Department of Natural Resources began intensive stocking of walleye fingerlings to bolster fish populations. Subsequent to stocking, the walleye fishery has recovered. The study objective was to determine if recovery was due to the stocking program or natural reproduction. Inherent genetic differences between hatchery fish and endemic walleyes were used to determine the effect and contribution of hatchery fish to Saginaw Bay.

Pulsed Plasma Processing of Diesel Engine Exhaust Final Report CRADA No. TC-0336-92-1-C

DOE Office of Scientific and Technical Information (OSTI.GOV)

Merritt, Bernard T.; Broering, Louis

The goal was to develop an exhaust-gas treatment process for the reduction of NO x and hydrocarbon from diesel engines. The project began believing that direct chemical reduction on NO x was possible through the use of non-thermal plasmas. The original CRADA began in 1993 and was scheduled to finish in 1996. It had as its goals three metrics: 1) remove two grams/brake-horse-power-hour of NOx, 2) have no more than five percent energy penalty, and 3) cost no more than ten percent of the engine cost. These goals were all aimed at heavy-duty diesel trucks. This CRADA had its Defensemore » Program funding eliminated by DOE prior to completion in 1995. Prior to loss of funding from DOE, LLNL discovered that due to the large oxygen content in diesel exhaust, direct chemical reduction was not possible. In understanding why, a breakthrough was achieved that combined the use of a non-thermal plasma and a catalyst. This process was named Plasma Assisted Catalytic Reduction (P ACR). Because of this breakthrough, the CRADA became a funds-in only CRADA, once DOE DP funding ended. As a result, the funding decreased from about 1M dollars per year to about $400k per year. Subsequently, progress slowed as well. The CRADA was amended several times to reflect the funds-in nature. At each amendment, the deliverables were modified; the goals remained the same but the focus changed from heavy-duty to lightduty to SUVs. The diesel-engine NO x problem is similar to the furnace and boiler NO x emission problem with the added constraint that ammonia-like additives are impractical for a mobile source. Lean-burning gasoline engines are an additional area of application because the standard three-way catalyst is rendered ineffective by the presence of oxygen. In the P ACR process an electrical discharge is used to create a non-thermal plasma that contains oxidative radicals O and OH. These oxidative radicals convert NO to NO 2. Selective catalytic reduction using a readily available catalyst

Complex Multi-Chamber Airbag Performance Simulation Final Report CRADA No. TSB-961-94

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kay, Gregory; Kithil, Philip

The purpose of this small business CRADA was to evaluate the performance of new airbag concepts which were developed by the Advanced Safety Concepts, Inc. (ASCI). These new airbag concepts, if successful, could have major potential savings to society in terms of fewer injuries, lost time and lives.

Physical limnology of Saginaw Bay, Lake Huron

USGS Publications Warehouse

Beeton, Alfred M.; Smith, Stanford H.; Hooper, Frank F.

1967-01-01

The average flushing time was 186 days, but was 113 days during the period of peak river discharge. The lakeward transport of Saginaw River water ranged from 619 to 2,294 feet per day in the inner bay to 1,410 to 3,000 feet per day in the outer bay on June 7 and October 30, respectively.

Trinitromethyl Heterocyclic Oxidizers as a Solid Propellant Ingredient Final Report CRADA No TC02146.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pagoria, P.; Racoveanu, A.

This was a collaborative effort between Lawrence Livermore National Security, LLC as manager and operator of Lawrence Livermore National Laboratory (LLNL) and Physical Sciences, Inc. (PSI), to develop a synthesis of two novel energetic heterocyclic oxidizers as possible replacements for ammonium perchlorate (AP) in rocket propellant formulations. This CRADA resulted from the award of the Phase I Small Business Technology Transfer (STTR) from DOD. The CRADA consisted of two phases. The goal for Phase 1 was to produce a new oxidizer called TNMDNP. Phase 2 is optional (based on the success of Phase 1) and the goal of Phase 2more » (optional) was to produce a new oxidizer called TNMDNT. Phase 2 tasks would be performed based on the successful results of Phase 1.« less

Development of lifetime test procedure for powder evacuated panel insulation. CRADA final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilkes, K E; Graves, R S; Childs, K W

This CRADA is between Appliance Research Consortium (ARC) of the Association of Home Appliance Manufacturers (AHAM) and the Lockheed Martin Energy Research Corp. A Powder Evacuated Panel (PEP) is a "super" thermal insulation, having a thermal resistivity (R) substantially above that of existing insulation without the environmental problems of some insulations such as Chlorofluorocarbon (CFC) blown foam.

Mobile Ocean Test Berth Support: Cooperative Research and Development Final Report, CRADA Number CRD-10-413

DOE Office of Scientific and Technical Information (OSTI.GOV)

LiVecchi, Albert

The Northwest National Marine Renewable Energy Center (NNMREC), headquartered at the Oregon State University, is establishing the capabilities to test prototype wave energy conversion devices in the ocean. This CRADA will leverage the technical expertise and resources at NREL in the wind industry and in ocean engineering to support and enhance the development of the NNMREC Mobile Ocean Test Berth (MOTB). This CRADA will provide direct support to NNMREC by providing design evaluation and review of the MOTB, developing effective protocols for testing of the MOTB and wave energy conversion devices in the ocean, assisting in the specification of appropriatemore » instrumentation and data acquisition packages, and providing guidance on obtaining and maintaining A2LA (American Association for Laboratory Accreditation) accreditation.« less

Development of a Multi-Sensor Cancer Detection Probe Final Report CRADA No. TC-2026-01

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marion, J.; Hular, R.

This collaboration continued work started under a previous CRADA (TSB-2023-00) to take a detailed concept specification for a multi-sensor needle/probe suitable for breast cancer analysis and produce a prototype system suitable for human FDA trials.

FFP/NREL Collaboration on Hydrokinetic River Turbine Testing: Cooperative Research and Development Final Report, CRADA Number CRD-12-00473

DOE Office of Scientific and Technical Information (OSTI.GOV)

Driscoll, F.

2013-04-01

This shared resources CRADA defines collaborations between the National Renewable Energy Laboratory (NREL) and Free Flow Power (FFP) set forth in the following Joint Work Statement. Under the terms and conditions described in this CRADA, NREL and FFP will collaborate on the testing of FFP's hydrokinetic river turbine project on the Mississippi River (baseline location near Baton Rouge, LA; alternate location near Greenville, MS). NREL and FFP will work together to develop testing plans, instrumentation, and data acquisition systems; and perform field measurements.

Geomorphology of the Chippewa River delta of Glacial Lake Saginaw, central Lower Michigan, USA

NASA Astrophysics Data System (ADS)

Connallon, Christopher B.; Schaetzl, Randall J.

2017-08-01

We introduce, characterize, and interpret the geomorphic history of a relict, Pleistocene-aged delta of the Chippewa River in central Lower Michigan. The broad, sandy Chippewa delta developed into various stages of Glacial Lake Saginaw, between ca. ≈ 17 and 15 ka·BP (calibrated ages). Although the delta was first identified in 1955 on a statewide glacial geology map, neither its extent nor its Pleistocene history had been previously determined. The delta is typically forested, owing to its wet, sandy soils, which stand out against the agricultural fields of the surrounding, loamy lake plain sediments. The delta heads near the city of Mt Pleasant and extends eastward onto the Saginaw Lowlands, i.e., the plain of Glacial Lake Saginaw. Data from 3285 water well logs, 180 hand augered sites, and 185 points randomly located in a GIS on two-storied (sand over loam) soils were used to determine the extent, textural properties, and thickness of the delta. The delta is ≈ 18 km wide and ≈ 38 km long and is sandy throughout. Deltaic sediments from neighboring rivers that also drained into Glacial Lake Saginaw merge with the lower Chippewa delta, obscuring its boundary there. The delta is thickest near the delta's head and in the center, but thins to 1-2 m or less on its eastern margins. Mean thicknesses are 2.3-2.9 m, suggestive of a thin sediment body, frequently impacted by the waves and fluctuating waters of the lakes. Although beach ridges are only weakly expressed across the delta because of the sandy sediment, the coarsest parts of the delta are generally coincident with some of these inferred former shorezones and have a broad, incised channel that formed while lake levels were low. The thick upper delta generally lies above the relict shorelines of Glacial Lakes Saginaw and Arkona (≈ 17.1 to ≈ 16 ka·BP), whereas most of the thin, distal delta is associated with Glacial Lake Warren (≈ 15 ka·BP). Together, these data suggest that the Chippewa delta formed

A 200 year chronology of burrowing mayflies (Hexagenia spp.) in Saginaw Bay

USGS Publications Warehouse

Schloesser, Donald W.; Robbins, John A.; Matisoff, Gerald; Nalepa, Thomas F.; Morehead, Nancy R.

2014-01-01

After an absence of 50 years, burrowing mayflies (Hexagenia spp.) colonized western Lake Erie which led to interest in whether this fauna can be used to measure recovery in nearshore waters throughout the Great Lakes. However, in many areas we do not know if mayflies were native/endemic and thus, whether recovery is a logical measure to assess progress of recovery. In the present study, we construct a chronologic record of relative abundance of burrowing mayflies in Saginaw Bay by the use of mayfly tusks and radionuclides in sediments (i.e., a paleoecologic record) and historic records of mayfly nymphs in the bay. These records reveal that mayflies: (1) were few before 1799, which indicates that nymphs were probably native/endemic in the bay, (2) increased between 1799 and 1807 and remained at relatively high levels between 1807 and 1965, probably in response to increased nutrient run-off from the watershed, (3) declined dramatically between 1965 and 1973, probably as a result of excessive eutrophication in the mid-1950s; and, (4) were few and highly variable between 1973 and 2001, probably as a result of low and unstable abundances of mayfly nymphs. Historic records verify that nymphs disappeared in the bay in the late-1950s to early-1960s which is in agreement with the paleoecologic record. Reoccurrence of low abundances of nymphs in the bay between 1991 and 2008 and comparison of chronologic records of nymphs in Saginaw Bay and western Lake Erie suggest that mayflies may return to Saginaw Bay in the early-21st century. Undoubtedly, watershed conservation and three decades of pollution abatement have set the stage for a recovery of burrowing mayflies in Saginaw Bay, and possibly in other areas of the Great Lakes.

CRADA Final Report for CRADA Number ORNL00-0605: Advanced Engine/Aftertreatment System R&D

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pihl, Josh A; West, Brian H; Toops, Todd J

2011-10-01

Navistar and ORNL established this CRADA to develop diesel engine aftertreatment configurations and control strategies that could meet emissions regulations while maintaining or improving vehicle efficiency. The early years of the project focused on reducing the fuel penalty associated with lean NOx trap (LNT), also known as NOx adsorber catalyst regeneration and desulfation. While Navistar pursued engine-based (in-cylinder) approaches to LNT regeneration, complementary experiments at ORNL focused on in-exhaust fuel injection. ORNL developed a PC-based controller for transient electronic control of EGR valve position, intake throttle position, and actuation of fuel injectors in the exhaust system of a Navistar enginemore » installed at Oak Ridge. Aftertreatment systems consisting of different diesel oxidation catalysts (DOCs) in conjunction with a diesel particle filter and LNT were evaluated under quasi-steady-state conditions. Hydrocarbon (HC) species were measured at multiple locations in the exhaust system with Gas chromatograph mass spectrometry (GC-MS) and Fourier transform infrared (FTIR) spectroscopy. Under full-load, rated speed conditions, injection of fuel upstream of the DOC reduced the fuel penalty for a given level of NOx reduction by 10-20%. GC-MS showed that fuel compounds were 'cracked' into smaller hydrocarbon species over the DOC, particularly light alkenes. GC-MS analysis of HC species entering and exiting the LNT showed high utilization of light alkenes, followed by mono-aromatics; branched alkanes passed through the LNT largely unreacted. Follow-on experiments at a 'road load' condition were conducted, revealing that the NOx reduction was better without the DOC at lower temperatures. The improved performance was attributed to the large swings in the NOx adsorber core temperature. Split-injection experiments were conducted with ultra-low sulfur diesel fuel and three pure HC compounds: 1-pentene, toluene, and iso-octane. The pure compound

Simulation of ground-water flow in the Saginaw Aquifer, Clinton, Eaton, and Ingham counties, Michigan

USGS Publications Warehouse

Holtschlag, David J.; Luukkonen, Carol L.; Nicholas, J.R.

1996-01-01

A numerical model was developed to simulate ground-water flow in the Tri-County region, which consists of Clinton, Eaton, and Ingham Counties, Michigan. This region includes a nine-township area surrounding Lansing, Michigan. The model simulates the regional response of the Saginaw aquifer to major groundwater withdrawals associated with public-supply wells. The Saginaw aquifer, which is in the Grand River and Saginaw Formations of Pennsylvanian age, is the primary source of ground water for Tri-County residents. The Saginaw aquifer is overlain by glacial deposits, which also are important ground-water sources in some locations. Flow in the Saginaw aquifer and the glacial deposits is simulated by discretizing the flow system into model cells arranged in two layers. Each cell, which corresponds to a land area of 0.0625 square mile, represents the locally averaged properties of the system. The spatial variation of hydraulic properties controlling ground-water flow was estimated by geostatistical analysis of 4,947 well logs. Parameter estimation, a form of nonlinear regression, was used to calibrate the flow model. Results of steady-state ground-water-flow simulations show close agreement between water flowing into and out of the model area for 1992 pumping conditions; standard error of the difference between simulated and measured heads is 14.7 feet. Simulation results for three alternative pumping scenarios for the year 2020 show that the glacial aquifer could be dewatered in places if hypothetical increases in pumping are not distributed throughout the Tri-County region. Contributing areas to public-supply wells in the nine-township area were delineated by a particle-tracking analysis. These areas cover about 121 square miles. Contributing areas for particles having travel times of 40 years or less cover about 42 square miles. Results of tritium sampling support results of model simulations to delineate contributing areas.

Improved Advanced Actuated Hybrid Mirrors Final Report CRADA No. TC02130.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barbee, T. W.; Ealey, M. A.

2017-08-25

This was a collaborative effort to develop and demonstrate an improved Advanced Actuated Hybrid Mirrors (AAHM) for commercial or Government purposes. The AAHM consists of a nanolaminate film replicating a precision optical surface bonded to a Silicon Carbide (SiC) substrate with active figure control capability. The goal of this project was to further the development of specific AAHM technologies. The intent of the CRADA was to combine the expertise of LLNL and NG Xinetics in the manufacture and test of a very high quality AAHM, incorporating lessons learned from earlier joint efforts.

Development of Personal Decontamination System Final Report CRADA No. TC-02078-04

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, W. J.; O'Dell, P.

2017-09-27

This was a collaborative effort between The Regents of the University of California, Lawrence Livermore National Laboratory (LLNL) and O’Dell Engineering, Ltd. (O’Dell) to develop an improved low-cost personal decontamination system for Toxic Industrial Chemicals (TICs) and chemical agents. The significant change to the project was that COTS (Commercial Off-the Shelf Components) were identified that performed as well, or better than, the proprietary materials created and tested as part of this CRADA. These COTS components were combined to create a new LPDS (low-cost personal decontamination system) that met all specifications.

Development of a Laser for Landmine Destruction Final Report CRADA No. TC02126.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yamamoto, R.; Sheppard, C.

2017-08-31

This was one of two CRADAs between Lawrence Livermore National Security, LLC as manager and operator of Lawrence Livermore National Laboratory (LLNL) and First Alliance Technologies, LLC (First Alliance), to conduct research and development activity toward an integrated system for the detecting, locating, and destroying of landmines and unexploded ordinance using a laser to destroy landmines and unexploded ordinance and First Alliance’s Land Mine Locator (LML) system.

cCRADA | FNLCR Staging

Cancer.gov

A contractor Cooperative Research and Development Agreement(cCRADA) is a partnering mechanism that expands the opportunities for FNLCR’s researchers to work with external parties to conduct collaborative research activities and explore develo

Hyperspectral Sensors Final Report CRADA No. TC02173.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Priest, R. E.; Sauvageau, J. E.

This was a collaborative effort between Lawrence Livermore National Security, LLC as manager and operator of Lawrence Livermore National Laboratory (LLNL) and Science Applications International Corporation (SAIC), National Security Space Operations/SRBU, to develop longwave infrared (LWIR) hyperspectral imaging (HSI) sensors for airborne and potentially ground and space, platforms. LLNL has designed and developed LWIR HSI sensors since 1995. The current generation of these sensors has applications to users within the U.S. Department of Defense and the Intelligence Community. User needs are for multiple copies provided by commercial industry. To gain the most benefit from the U.S. Government’s prior investments inmore » LWIR HSI sensors developed at LLNL, transfer of technology and know-how from LLNL HSI experts to commercial industry was needed. The overarching purpose of the CRADA project was to facilitate the transfer of the necessary technology from LLNL to SAIC thereby allowing the U.S. Government to procure LWIR HSI sensors from this company.« less

Managing Vacant and Abandoned Property in the Green Zone of Saginaw, Michigan

EPA Pesticide Factsheets

Report from a technical assistance project with Saginaw, MI, gives the city options to consider to stabilize neighborhoods through sustainable reuse of abandoned properties, including redeveloping them as green infrastructure, and to create opportunities.

Renewable Energy Opportunities Saginaw Chippewa Indian Tribe

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saginaw Chippewa Indian Tribe Planning Department; Smiley, Steve; Bennett, Keith, DOE Project Officer

2008-10-22

The Saginaw Chippewa Indian Tribe has a vision to become self-sufficient in its energy needs and to maintain its culture and protect Mother Earth with respect and honor for the next seven generations. To achieve this vision, green energy sources such as solar, wind and biomass energy are the best energy paths to travel. In this feasibility study the Tribe has analyzed and provided data on the nature of the renewable resources available to the Tribe and the costs of implementing these technologies.

Exploring potential effects of cormorant predation on the fish community in Saginaw Bay, Lake Huron

USGS Publications Warehouse

DeBruyne, Robin L.; Fielder, David G.; Roseman, Edward; Butchko, Peter H.

2017-01-01

Stakeholders and fishery managers expressed concern that double-crested cormorant Phalacrocorax auritus predation may be a factor in the recent poor survival of yellow perch Perca flavescens in Saginaw Bay. We quantified cormorant diets from two nesting colonies in Saginaw Bay during April–September in 2013 and 2014, with special emphasis on impacts to yellow perch. Cormorants (n = 691) were collected when returning to colonies after foraging. Stomachs were removed and preserved in the field. Diet items were identified, enumerated, and measured (n = 23.373). Cormorant diets from Saginaw Bay indicate a heavy reliance on round goby and Notropis species as prey during the breeding season, consistent with other areas of the Great Lakes where round goby and cormorants coincide. Respectively, the three most common prey species observed by number (%) and biomass (%) pooled across years and sites were round goby Neogobius melanostomus (56.6%, 42.1%), emerald shiner Notropis antherinoides (25.2%, 12.5%), and yellow perch (8.0%, 14.1%). Diet composition was more variable at Spoils Island than at Little Charity Island. Overall cormorant consumption (estimated using cormorant consumption demand rates) of yellow perch was compared to walleye consumption. Cormorant consumption of age-1 yellow perch was 13–17% as much as mean walleye consumption of yellow perch in 2013 and 8–11% in 2014. The cumulative effects of walleye and spring cormorant predation likely represent a recruitment bottleneck for yellow perch in Saginaw Bay. Future studies determining age-specific abundance of yellow perch would facilitate better determination of cormorant predation significance.

CRADAs: They're Not Just for NCI Anymore | Poster

Cancer.gov

By Karen Surabian, Thomas Stackhouse, and Jeffrey Thomas, Contributing Writers, and Bruce Crise, Guest Writer Advancing scientific discovery is increasingly dependent on diverse and innovative partnerships, and the Cooperative Research and Development Agreement (CRADA) is an essential tool for establishing partnerships. CRADAs allow a federal laboratory to enter into

Development of YBCO Superconductor for Electric Systems: Cooperative Research and Development Final Report, CRADA Number CRD-04-150

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bhattacharya, R.

2013-03-01

The proposed project will be collaborative in exploration of high temperature superconductor oxide films between SuperPower, Inc. and the National Renewable Energy Laboratory. This CRADA will attempt to develop YBCO based high temperature oxide technology.

Ink Jet Printing for Silicon Photovoltaics: Cooperative Research and Development Final Report, CRADA Number CRD-04-00139

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ginley, D. S.

2010-08-01

The purpose of this CRADA was to combine the strengths of NREL and Evergreen Solar in the area of ink jet printing to develop a new manufacturing technology necessary to produce Si solar cells based on ribbon technology comparable to or exceeding current technologies.

Scale Up of Malonic Acid Fermentation Process: Cooperative Research and Development Final Report, CRADA Number CRD-16-612

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schell, Daniel J

The goal of this work is to use the large fermentation vessels in the National Renewable Energy Laboratory's (NREL) Integrated Biorefinery Research Facility (IBRF) to scale-up Lygos' biological-based process for producing malonic acid and to generate performance data. Initially, work at the 1 L scale validated successful transfer of Lygos' fermentation protocols to NREL using a glucose substrate. Outside of the scope of the CRADA with NREL, Lygos tested their process on lignocellulosic sugars produced by NREL at Lawrence Berkeley National Laboratory's (LBNL) Advanced Biofuels Process Development Unit (ABPDU). NREL produced these cellulosic sugar solutions from corn stover using amore » separate cellulose/hemicellulose process configuration. Finally, NREL performed fermentations using glucose in large fermentors (1,500- and 9,000-L vessels) to intermediate product and to demonstrate successful performance of Lygos' technology at larger scales.« less

Application of LANDSAT to the Surveillance and Control of Eutrophication in Saginaw Bay

NASA Technical Reports Server (NTRS)

Rogers, R. H. (Principal Investigator)

1975-01-01

The author has identified the following significant results. LANDSAT digital data and ground truth measurements for Saginaw Bay (Lake Huron), Michigan, for 3 June 1974 can be correlated by stepwise linear regression technique and the resulting equations used to estimate invisible water quality parameters in nonsampled areas. Correlation of these parameters with each other indicates that the transport of Saginaw River water can now be traced by a number of water quality features, one or more of which are directly detected by LANDSAT. Five of the 12 water quality parameters are best correlated with LANDSAT band 6 measurements alone. One parameter (temperature) relates to band 5 alone and the remaining six may be predicted with varying degrees of accuracy from a combination of two bands (first band 6 and generally band 4 second).

CRADAs: They're Not Just for NCI Anymore | Poster

Cancer.gov

By Karen Surabian, Thomas Stackhouse, and Jeffrey Thomas, Contributing Writers, and Bruce Crise, Guest Writer Advancing scientific discovery is increasingly dependent on diverse and innovative partnerships, and the Cooperative Research and Development Agreement (CRADA) is an essential tool for establishing partnerships. CRADAs allow a federal laboratory to enter into collaborative research and development (R&D) projects with outside parties (commercial or nonprofit).

Application of powder metallurgy techniques for the development of non-toxic ammunition. Final CRADA report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lowden, R.; Kelly, R.

1997-05-30

The purpose of the Cooperative Research and Development Agreement (CRADA) between Martin Marietta Energy Systems, Inc., and Delta Frangible Ammunition (DFA), was to identify and evaluate composite materials for the development of small arms ammunition. Currently available small arms ammunition utilizes lead as the major component of the projectile. The introduction of lead into the environment by these projectiles when they are expended is a rapidly increasing environmental problem. At certain levels, lead is a toxic metal to the environment and a continual health and safety concern for firearm users as well as those who must conduct lead recovery operationsmore » from the environment. DFA is a leading supplier of high-density mixtures, which will be used to replace lead-based ammunition in specific applications. Current non-lead ammunition has several limitations that prevent it from replacing lead-based ammunition in many applications (such as applications that require ballistics, weapon recoil, and weapon function identical to that of lead-based ammunition). The purpose of the CRADA was to perform the research and development to identify cost-effective materials to be used in small arms ammunition that eventually will be used in commercially viable, environmentally conscious, non-lead, frangible and/or non-frangible, ammunition.« less

Frito-Lay North America/NREL CRADA: Cooperative Research and Development Final Report, CRADA Number CRD-06-176

DOE Office of Scientific and Technical Information (OSTI.GOV)

Walker, A.

2013-06-01

Frito Lay North America (FLNA) requires technical assistance for the evaluation and implementation of renewable energy and energy efficiency projects in production facilities and distribution centers across North America. Services provided by NREL do not compete with those available in the private sector, but rather provide FLNA with expertise to create opportunities for the private sector renewable/efficiency industries and to inform FLNA decision making regarding cost-effective projects. Services include: identifying the most cost-effective project locations based on renewable energy resource data, utility data, incentives and other parameters affecting projects; assistance with feasibility studies; procurement specifications; design reviews; and other servicesmore » to support FNLA in improving resource efficiency at facilities. This Cooperative Research and Development Agreement (CRADA) establishes the terms and conditions under which FLNA may access capabilities unique to the laboratory and required by FLNA. Each subsequent task issued under this umbrella agreement would include a scope-of-work, budget, schedule, and provisions for intellectual property specific to that task.« less

TRANSCRIPTIONAL PROFILING USING THE FLOWTHROUGH GENOSENSOR FINAL CRADA REPORT C/ORNL97-00472

DOE Office of Scientific and Technical Information (OSTI.GOV)

Doktycz, M. J.; Yang, H.

1999-06-01

A Cooperative Research and Development Agreement (CRADA) between Lockheed Martin Energy Research Corporation (Contractor) and Gene Logic, Inc., (Participant) was carried out to evaluate the technical feasibility study of the application of the flowthrough genosensor for gene expression (transcriptional) profiling, over the current industry practice of using flat surface hybridization arrays to monitor the relative abundance of individual mRNA species in a cell. Various parameters, including substrate preparation, flow rates, hybridization conditions and sample concentrations, were evaluated on the flowthrough genosensor. The superiority of the flowthrough genosensor, in terms of hybridization rate and sensitivity were established.

Laser Materials Processing Final Report CRADA No. TC-1526-98

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crane, J.; Lehane, C. J.

2017-09-08

This CRADA project was a joint effort between Lawrence Livermore National Laboratory (LLNL) and United Technologies Corporation (UTC)/Pratt & Whitney (P&W) to demonstrate process capability for drilling holes in turbine airfoils using LLNL-developed femtosecond laser machining technology. The basis for this development was the ability of femtosecond lasers to drill precision holes in variety of materials with little or no collateral damage. The ultimate objective was to develop a laser machine tool consisting of an extremely advanced femtosecond laser subsystem to be developed by LLNL on a best-effort basis and a drilling station for turbine blades and vanes to bemore » developed by P&W. In addition, P&W was responsible for commercializing the system. The goal of the so called Advanced Laser Drilling (ALD) system was to drill specified complex hole-shapes in turbine blades and vanes with a high degree precision and repeatability and simultaneously capable of very high speed processing.« less

Manufacturing and Characterization of Ultra Pure Ferrous Alloys Final Report CRADA No. TC02069.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lesuer, D.; McGreevy, T. E.

This CRADA was a.collaborative effort between the Lawrence Livermore National Security LLC (formerly University of California)/Lawrence Livermore National Laboratory (LLNL),and Caterpillar Inc. (CaterpiHar), to further advance levitation casting techniques (developed at the Central Research Institute for Material (CRIM) in St. Petersburg, Russia) for use in manufacturing high purity metal alloys. This DOE Global Initiatives for Proliferation Prevention Program (IPP) project was to develop and demonstrate the levitation casting technology for producing ultra-pure alloys.

High Resolution Sub-MM Fiberoptic Endoscope Final Report CRADA No. TSB-1447-97

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stone, Gary F.; Smith, John

2018-01-22

At the time of the CRADA, LLNL needed to develop a sub-mm outer diameter fiberoptic endoscope with 25pm or better resolution at 3-lOmm working distance to support the Enhanced Surveillance Program (ESP) and the Core Surveillance Program for DOE. The commercially available systems did not meet the image resolution requirements and development work was needed to reach three goals. We also needed to perform preliminary investigations into the production of such an endoscope with a steerable-articulated distal end. The goal of such an endoscope was to allow for a 45 degree inspection cone including the lens field of view.

Fiber Based Optical Amplifier for High Energy Laser Pulses Final Report CRADA No. TC02100.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Messerly, M.; Cunningham, P.

This was a collaborative effort between Lawrence Livermore National Security, LLC (formerly The Regents of the University of California)/Lawrence Livermore National Laboratory (LLNL), and The Boeing Company to develop an optical fiber-based laser amplifier capable of producing and sustaining very high-energy, nanosecond-scale optical pulses. The overall technical objective of this CRADA was to research, design, and develop an optical fiber-based amplifier that would meet specific metrics.

High Performance Parallel Processing (HPPP) Finite Element Simulation of Fluid Structure Interactions Final Report CRADA No. TC-0824-94-A

DOE Office of Scientific and Technical Information (OSTI.GOV)

Couch, R.; Ziegler, D. P.

This project was a muki-partner CRADA. This was a partnership between Alcoa and LLNL. AIcoa developed a system of numerical simulation modules that provided accurate and efficient threedimensional modeling of combined fluid dynamics and structural response.

Characterization of the Tribological Behavior of Oxide-Based NanoMaterials: Final CRADA Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fenske, George

2017-01-04

Under the Argonne/Pixelligent cooperative research and development agreement (CRADA – C1200801), Argonne performed labscale tribological tests on proprietary nano-sized ZrO 2 material developed by Pixelligent. Pixelligent utilized their proprietary process to prepare variants with different surfactants at different loadings in different carrier fluids for testing and evaluation at Argonne. Argonne applied a range of benchtop tribological test rigs to evaluate friction and wear under a range of conditions (contact geometry, loads, speeds, and temperature) that simulated a broad range of conditions experienced in engines and driveline components. Post-test analysis of worn surfaces provided information on the structure and chemistry ofmore » the tribofilms produced during the tests.« less

Tire Development for Effective Transportation and Utilization of Used Tires, CRADA 01-N044, Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Susan M. Maley

Scrap tires represent a significant disposal and recycling challenge for the United States. Over 280 million tires are generated on an annual basis, and several states have large stockpiles or abandoned tire piles that are slated for remediation. While most states have programs to address the accumulation and generation of scrap tires, most of these states struggle with creating and sustaining recycling or beneficial end use markets. One of the major issues with market development has been the costs associated with transporting and processing the tires into material for recycling or disposal. According to a report by the Rubber Manufacturesmore » Association tire-derived fuel (TDF) represents the largest market for scrap tires, and approximately 115 million tires were consumed in 2001 as TDF (U.S. Scrap Tire Markets, 2001, December 2002, www.rma.org/scraptires). This market is supported primarily by cement kilns, followed by various industries including companies that operate utility and industrial boilers. However the use of TDF has not increased and the amount of TDF used by boiler operators has declined. The work completed through this cooperative research and development agreement (CRADA) has shown the potential of a mobile tire shredding unit to economically produce TDF and to provide an alterative low cost fuel to suitable coal-fired power systems. This novel system addresses the economic barriers by processing the tires at the retailer, thereby eliminating the costs associated with hauling whole tires. The equipment incorporated into the design allow for small 1-inch chunks of TDF to be produced in a timely fashion. The TDF can then be co-fired with coal in suitable combustion systems, such as a fluidized bed. Proper use of TDF has been shown to boost efficiency and reduce emissions from power generation systems, which is beneficial to coal utilization in existing power plants. Since the original scope of work outlined in the CRADA could not be completed

Improved Design/Reduction of Manufacturing Costs of Space-Traveling Wave Tiube Amplifiers Final Report CRADA No. TC-0461-93

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shang, C. C.; Drasco, M.

The purpose of the CRADA was to develop new microwave codes for analyzing both slow-,vave structures and beam-wave interactions of traveling wave tube amplifiers (TWTA), the microwave power source for satellite and radar communication systems. The scope of work also included testing and improving power modules through measurements and simulation.

Saginaw Drug and Alcohol Abuse Education and Training Program: Product Evaluation, 1990-1991.

ERIC Educational Resources Information Center

Saginaw Public Schools, MI. Dept. of Evaluation Services.

This report evaluates the Saginaw Drug and Alcohol Abuse Education Training Program conducted in 1990-1991, which provided in-depth training for 94 professionals including 63 teachers and 7 counselors through a workshop lasting 5 days and containing 6 hours of instruction per day. The workshops addressed the identification of both drug abuse…

Development of Abrasion-Resistant Coating for Solar Reflective Films. Cooperative Research and Development Final Report, CRADA Number CRD-07-247

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gray, Matthew

The purpose of this CRADA is to develop an abrasion-resistant coating, suitable for use on polymeric-based reflective films (e.g., the ReflecTech reflective film), that allows for improved scratch resistance and enables the use of aggressive cleaning techniques (e.g., direct contact methods like brushing) without damaging the specular reflectance properties of the reflective film.

cCRADA | Frederick National Laboratory for Cancer Research

Cancer.gov

A contractor Cooperative Research and Development Agreement(cCRADA) is a partnering mechanism that expands the opportunities for Frederick National Laboratoryresearchers to work with external parties to conduct collaborative research acti

Low Voltage Electron Beam Processing Final Report CRADA No. TC-645-93-A

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, H.; Wakalopulos, G.

This CRADA project was established to develop a small, inexpensive sealed-tube electron beam processing system having immediate applications in industrial, high speed manufacturing processes, and in the Department of Energy (DOE) waste treatment/cleanup operations. The technical work involved the development and demonstration of a compact, sealed, 50-75 kilovolt (kV) EB generator prototype, including controls and power supply. The specific goals of this project were to develop a low cost vacuum tube capable of shooting an electron beam several inches into the air, and to demonstrate that wide area materials processing is feasible by stacking the tubes to produce continuous beams.more » During the project, we successfully demonstrated the producibility of a low cost electron beam system and several material processing operations of interest to US industry, DOE and, since September 11, 2001, the Homeland Security.« less

CRADA opportunities in pressurized combustion research

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maloney, D J; Norton, T S; Casleton, K H

1995-06-01

The Morgantown Energy Technology Center recently began operation of a Low Emissions Combustor Test and Research (LECTR) Facility. This facility was built to support the development of Advanced Gas Turbine Systems (ATS) by providing test facilities and engineering support to METC customers through the ATS University-Industry Consortium and through CRADA participation with industrial partners.

CRADA Payment Options | NCI Technology Transfer Center | TTC

Cancer.gov

NCI TTC CRADA PAYMENT OPTIONS: Electronic Payments by Wire Transfer via Fedwire, Mail a check to the Institute or Center, or Automated Clearing House (ACH)/Electronic Funds Transfer (ETF) payments via Pay.gov (NCI ONLY).

Computer Mapping of Water Quality in Saginaw Bay with LANDSAT Digital Data

NASA Technical Reports Server (NTRS)

Rogers, R. H. (Principal Investigator); Shah, N. J.; Smith, V. E.; Mckeon, J. B.

1976-01-01

The author has identified the following significant results. LANDSAT digital data and ground truth measurements for Saginaw Bay (Lake Huron), Michigan, for 31 July 1975 were correlated by stepwise linear regression and the resulting equations used to estimate invisible water quality parameters in nonsampled areas. Chloride, conductivity, total Kjeldahl nitrogen, total phosphorus, and chlorophyll a were best correlated with the ratio of LANDSAT Band 4 to Band 5. Temperature and Secchi depth correlate best with Band 5.

Development of Isotropic, Micro-Toughened Titanium-Base Intermetallic Composites for High-Temperature Service Final Report CRADA No. TC-0497-93A

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nieh, T. G.; Waltz, Z. R.

The purpose of this Cooperative Research and Development Agreement (CRADA) between LLNL and P&W is to develop advanced composites and their processing technologies, resulting in major improviements in the ductility and toughnes of high-strength, high-stiffness TiAl-base composite materials for commercial jet engines and U.S. Department of Energy (DOE) Defense Program applications.

Commercialization of Ultra-Hard Ceramics for Cutting Tools Final Report CRADA No. TC0279.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Landingham, R.; Neumann, T.

This was a collaborative effort between Lawrence Livermore National Security, LLC as manager and operator of Lawrence Livermore National Laboratory (LLNL) and Greenleaf Corporation (Greenleaf) to develop the technology for forming unique precursor nano-powders process that can be consolidated into ceramic products for industry. LLNL researchers have developed a solgel process for forming nano-ceramic powders. The nano powders are highly tailorable, allowing the explicit design of desired properties that lead to ultra hard materials with fine grain size. The present CRADA would allow the two parties to continue the development of the sol-gel process and the consolidation process in ordermore » to develop an industrially sound process for the manufacture of these ultra-hard materials.« less

Telemedicine. Final report/project accomplishments summary CRADA number 95-KCP-1014

DOE Office of Scientific and Technical Information (OSTI.GOV)

VanDeusen, A.L.

1997-04-01

This project was initiated to fill existing voids in the telemedicine equipment market. Currently, when a medical facility adds telemedicine capability to their video conference system, they must purchase expensive and bulky encoders and decoders in order to send information over the available data channel. Even with this expensive equipment, only one data type (stethoscope or ECG) can be sent at a time. In addition, since existing encoders and decoders are not designed specifically for telemedicine, special cables must be built to connect with this equipment. This project resulted in the design and construction of an encoder/decoder system that resolvedmore » these issues. The unit (referred to as the Telecoder) is designed specifically for the telemedicine market. The Telecoder is compact, handles two types of data (stethoscope and ECG) simultaneously, integrates with existing medical equipment, and is less expensive. In addition to the Telecoder module, a prototype was built that adds all the necessary logic and interfaces necessary to integrate the basic encoder design into additional Cardionics products. Although a complete integration into other Cardionics products was not in the scope of this CRADA, all the basic design work has been done to allow Cardionics to complete the work.« less

Effects of long-term changes in the benthic community on yellow perch in Saginaw Bay, Lake Huron

USGS Publications Warehouse

Schaeffer, Jeffrey S.; Diana, James S.; Haas, Robert C.

2000-01-01

Abundance, mortality, age and growth, food habits, and energetics of a yellow perch Perca flavescens population were investigated in eutrophic Saginaw Bay, Lake Huron during May to October, 1986 to 1988, and compared population characteristics with historical data from times when eutrophic conditions were less severe. During 1986 to 1988, yellow perch were abundant, but grew slowly and experienced high natural mortality. A size threshold was present at 150 to 180 mm beyond which few individuals survived, and sex ratios became biased toward males. An energetic model suggested that yellow perch were food limited; as they increased in size they spent a greater proportion of the growing season near maintenance ration. Low feeding rates were a consequence of subsistence on small chironomid larvae. Piscivory provided little energetic relief. Historical data suggested that availability of large benthic prey such as nymphs of the burrowing mayfly Hexagenia was important to yellow perch. Yellow perch formerly consumed Hexagenia, but mayflies were extirpated from Saginaw Bay during 1953 to 1965, and never recovered. When Hexagenia was present, yellow perch growth was moderate to fast depending on population size, size thresholds were not present, and yellow perch reached large size and older age despite moderate to high fishing mortality. Decreases in yellow perch growth rates during 1952 to 1955 coincided with extirpation of Hexagenia. Fast growth of yellow perch did occur after Hexagenia became extirpated, but only when fishing mortality was high, population size was small, and some large benthic invertebrates remained. Eutrophication of Saginaw Bay appeared to affect yellow perch by changing species composition and reducing size structure of the benthic community.

Development of Operational Free-Space-Optical (FSO) Laser Communication Systems Final Report CRADA No. TC02093.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ruggiero, A.; Orgren, A.

This project was a collaborative effort between Lawrence Livermore National Security, LLC (formerly The Regents of the University of California)/Lawrence Livermore National Laboratory (LLNL) and LGS Innovations, LLC (formerly Lucent Technologies, Inc.), to develop long-range and mobile operational free-space optical (FSO) laser communication systems for specialized government applications. LLNL and LGS Innovations formerly Lucent Bell Laboratories Government Communications Systems performed this work for a United States Government (USG) Intelligence Work for Others (I-WFO) customer, also referred to as "Government Customer", or "Customer" and "Government Sponsor." The CRADA was a critical and required part of the LLNL technology transfer plan formore » the customer.« less

Development of HANAA to Achieve Commercialization Final Report CRADA No. TC-2025-01

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koopman, R. P.; Schmidt, J. C.

The objective of this project was to provide DOD and the intelligence agencies with highly portable, advanced, bio-detection instruments and to further the DOE objective of putting advanced instrumentation for the detection of biological terrorism agents into the hands of first responders. All sponsors of the HANAA development work at LLNL believed that the technology must be commercialized to fully contribute to their missions. Intelligence organizations, military teams, and first responders must be able to purchase the instruments for a reasonable price and obtain maintenance services and support equipment from a reliable supplier in order for the instrument to bemore » useful to them. The goal was to efficiently transfer HANAA technology from LLNL to ETG, a company that would manufacture the instrument and make it commercially available to the constituencies important to our sponsors. This was to include a current beta test instrument and all knowledge of problems with the instrument and recommendations for solving those problems in a commercial version. The following tasks were to be completed under this CRADA.« less

Commercialization Plan Support for Development of Low Cost Vacuum Insulating Glazing: Cooperative Research and Development Final Report, CRADA Number CRD-11-449

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dameron, Arrelaine

During the duration of this CRADA, V-Glass and NREL will partner in testing, analysis, performance forecasting, costing, and evaluation of V-Glass’s GRIPWELD™ process technology for creating a low cost hermetic seal for conventional and vacuum glazing. Upon successful evaluation of hermeticity, V-Glass’s GRIPWELD™ will be evaluated for its potential use in highly insulating window glazing.

Mink biomagnification factors for dioxin-like compounds fed Saginaw Bay carp

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kubiak, T.J.; Tillitt, D.E.; Heaton, S.N.

1994-12-31

Diets containing 0, 10, 20 and 40% Saginaw Bay carp were fed to ranch mink to assess reproductive effects. All carp diets adversely affected reproduction. The diets and livers of the adult mink at the end of the study were chemically analyzed for planar halogenated hydrocarbons (PHHS) that induce aryl hydrocarbon hydroxylase (AHH)/ethoxyresorufin o-deethylase (EROD). Biomagnification factors (BMFS) from diets to mink livers were calculated. AHH and EROD-active PCB congeners uniformly magnified across diets except for PCB 126, which had higher magnification at lowest carp and control diets. PCB and PCDF congener magnification ranged from incalculable to 60-fold higher andmore » individual PCDDs ranged from incalculable to 165 times the diet. As expected from previous mammalian studies, 2378-TCDD magnified over an order of magnitude more than 2378-TCDF but by 4 to 5-fold less than 23478-PCDF. Based on dioxin equivalents theory and TEFS, PCB 126 ranked first in the liver residues of 2378-TCDD equivalents followed by PCB 105, 23478-PCDF and 2378-TCDD. Magnification factors allow for interpretation of relative exposure risks from certain wild forage species if wild mink liver concentrations are known. Conversely, knowledge of wild mink forage item concentrations allows for calculation of an estimated wild mink liver residue, when the concentration and dietary forage percentage are multiplied by the BMF. Therefore, BMFs can assist in the elucidation of relative risk of a population to these contaminants without necessarily having large numbers of mink samples, especially in habitats such as the Saginaw Bay area where mink and otter populations are presumed to be affected by high PHH contamination.« less

Sugar beet activities of the USDA-ARS East Lansing conducted in cooperation with Saginaw Research & Extension Center during 2016

USDA-ARS?s Scientific Manuscript database

Evaluation and rating plots were planted at the Saginaw Valley Research & Extension Center (SVREC) in Frankenmuth, MI in 2016 that focused on Cercospora leaf spot (CLS) and Rhizoctonia crown and root rot (CRR) disease performance of a wide range of Beta vulgaris materials. CLS and CRR trials were co...

Advanced Borobond™ Shields for Nuclear Materials Containment and Borobond™ Immobilization of Volatile Fission Products - Final CRADA Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wagh, Arun S.

2016-05-19

Borobond is a company-proprietary material developed by the CRADA partner in collaboration with Argonne, and is based on Argonne's Ceramicrete technology. It is being used by DOE for nuclear materials safe storage, and Boron Products, LLC is the manufacturer and supplier of Borobond. The major objective of this project was to produce a more versatile composition of this material and find new applications. Major target applications were use for nuclear radiation shields, such as in dry storage casks; use in immobilization of most difficult waste streams, such as Hanford K-Basin waste; use for soluble and volatile fission products, such asmore » Cs, Tc, Sr, and I; and use for corrosion and fire protection applications in nuclear facilities.« less

Atrial Model Development and Prototype Simulations: CRADA Final Report on Tasks 3 and 4

DOE Office of Scientific and Technical Information (OSTI.GOV)

O'Hara, T.; Zhang, X.; Villongco, C.

2016-10-28

The goal of this CRADA was to develop essential tools needed to simulate human atrial electrophysiology in 3-dimensions using an anatomical image-based anatomy and physiologically detailed human cellular model. The atria were modeled as anisotropic, representing the preferentially longitudinal electrical coupling between myocytes. Across the entire anatomy, cellular electrophysiology was heterogeneous, with left and right atrial myocytes defined differently. Left and right cell types for the “control” case of sinus rhythm (SR) was compared with remodeled electrophysiology and calcium cycling characteristics of chronic atrial fibrillation (cAF). The effects of Isoproterenol (ISO), a beta-adrenergic agonist that represents the functional consequences ofmore » PKA phosphorylation of various ion channels and transporters, was also simulated in SR and cAF to represent atrial activity under physical or emotional stress. Results and findings from Tasks 3 & 4 are described. Tasks 3 and 4 are, respectively: Input parameters prepared for a Cardioid simulation; Report including recommendations for additional scenario development and post-processing analytic strategy.« less

Conversion of Indigenous Agricultural Waste Feedstocks to Fuel Ethanol. Cooperative Research and Development Final Report, CRADA Number CRD-13-504

DOE Office of Scientific and Technical Information (OSTI.GOV)

Elander, Richard

This Cooperative Research and Development Agreement (CRADA) is between the National Renewable Energy Laboratory (NREL), a world leader in biomass conversion research and Ecopetrol American Inc., Ecopetrol S.A.'s U.S. subsidiary. The research and development efforts described in the Joint Work Statement (JWS) will take advantage of the strengths of both parties. NREL will use its Integrated Biorefinery Facility and vast experience in the conversion of lignocellulosic feedstocks to fuel ethanol to develop processes for the conversion of Ecopetrol's feedstocks. Ecopetrol will establish the infrastructure in Columbia to commercialize the conversion process.

High Temperature Catalytic Combustion Suppports Final Report CRADA No. TSB-0841-94

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hair, Lucy; Magno, Scott

This Small Business CRADA between LLNL and Catalytica was executed on January 25, 1995. The total estimated cost of this project was 113K. LLNL's contribution was estimated at $50K funded under the DOE/Defense Program Small Business Initiative. Catalytica's in-kind contribution was estimated at 63K. Catalytic combusion catalyst systems operate at temperatures from 600°C to above 1300°C. Catalytica has developed technology that limits the catalyst temperature to below 1000°C. At temperatures in the range of 850 to 1000°C, the thermal stability of the catalyst is an important issue. Typical supports such as stabilized aluminas, hexaluminates, zirconia and stabilized zirconia supports aremore » typically used but lack either thermal stability or other desirable properties. Catalytica had developed a new concept for thermally stable mixed oxide supports but this concept required the preparation of molecularly uniform precursors; that is, prior to high temperature treatment of these materials, the elements that make up the mixed oxide must be as nearly uniform as possible on a molecular level. The technique of sol gel processing appeared to be the preferred technique to make these molecularly uniform precursors, and a cooperative program with LLNL was established to prepare and test the proposed compounds. Catalytica proposed the composition and concentration levels for the materials to be prepared.« less

Predictive Model and Methodology for Heat Treatment Distortion Final Report CRADA No. TC-298-92

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nikkel, D. J.; McCabe, J.

This project was a multi-lab, multi-partner CRADA involving LLNL, Los Alamos National Laboratory, Sandia National Laboratories, Oak Ridge National Laboratory, Martin Marietta Energy Systems and the industrial partner, The National Center of Manufacturing Sciences (NCMS). A number of member companies of NCMS participated including General Motors Corporation, Ford Motor Company, The Torrington Company, Gear Research, the Illinois Institute of Technology Research Institute, and Deformation Control Technology •. LLNL was the lead laboratory for metrology technology used for validation of the computational tool/methodology. LLNL was also the lead laboratory for the development of the software user interface , for the computationalmore » tool. This report focuses on the participation of LLNL and NCMS. The purpose of the project was to develop a computational tool/methodology that engineers would use to predict the effects of heat treatment on the _size and shape of industrial parts made of quench hardenable alloys. Initially, the target application of the tool was gears for automotive power trains.« less

Sugarbeet Activities of the USDA-ARS East Lansing Conducted in Cooperation with Saginaw Valley Bean and Beet Farm during 2008

USDA-ARS?s Scientific Manuscript database

Four evaluation plots were planted at the Michigan State University Saginaw Valley Bean and Beet Research Farm in 2008. Test 08BB01 was specifically designed to evaluate a number of non-traditional yield and physiological measures that had been suggested from earlier trials, in addition to the more ...

Computer mapping of turbidity and circulation patterns in Saginaw Bay, Michigan from LANDSAT data

NASA Technical Reports Server (NTRS)

Rogers, R. H. (Principal Investigator); Reed, L. E.; Smith, V. E.

1975-01-01

The author has identified the following significant results. LANDSAT was used as a basis for producing geometrically-corrected, color-coded imagery of turbidity and circulation patterns in Saginaw Bay, Michigan (Lake Huron). This imagery shows nine discrete categories of turbidity, as indicated by nine Secchi depths between 0.3 and 3.3 meters. The categorized imagery provided an economical basis for extrapolating water quality parameters from point samples to unsample areas. LANDSAT furnished a synoptic view of water mass boundaries that no amount of ground sampling or monitoring could provide.

Sugar Beet Activities of the USDA-ARS East Lansing Conducted in Cooperation with Saginaw Valley Bean and Beet Farm During 2009

USDA-ARS?s Scientific Manuscript database

Two evaluation plots were planted at the Saginaw Valley Research & Extension Center in Frankenmuth, MI in 2009; one agronomic trial and one combined Cercospora evaluation trial. All trials were planted, following normal fall and spring tillage operations, with a USDA-ARS modified John Deere/Almaco ...

Advanced High Power mm-Wave Microwave Devices Final Report CRADA No. TC-0287-92

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shang, C. C.; Tomlin, T.

The purpose of this CRADA was to improve existing high-average-power microwave devices and develop the next generation microwave devices for energy and defense applications. A Free Electron Maser was under test at the FOM Institute (Rijnhuizen) Netherlands with the goal of producing a lMW-long pulse to CW microwave output in the range 130GHz to 250GHz. The DC acceleration and beam transport system is eventually to be used in a depressed collector cotilguration requiring 99.8% beam transmission in order that the high voltage 2MV supply be required only to supply 20 milliamps of body current. A relativistic version of the Herrmannmore » optical theory originally developed for microwave tube beams was used to take into account thermal elections far out on the gaussian distribution tail that can translate into beam current well outside the ideal beam edge. This theory was applied to the FOM beamline design and predicts that the beam envelope containing 99.8% of the current can be successfully transported to the undulator for a wide range of assumed eminence values.« less

Development of a Delivery System for Treating Cerebrovascular Aneurysms Final Report CRADA No. TC-1440-97

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, A.; Derbin, J. T.

The objective of the project was to develop a system for delivering an implantable medical device used to treat cerebrovascular aneurysms, which can cause disability or hemorrhagic stroke (over 15,000 strokes in the U.S. each year are caused by ruptured aneurysms). Micrus has developed an implantable device with the potential to significantly improve the treatment of cerebrovascular aneurysms. This implantable device should significantly reduce the number of hemorrhagic strokes. LLNL has performed proof-of-concept experiments for a delivery system that could be modified to deploy the Micrus device into aneurysms. The purpose of this CRADA was to complete development of themore » LLNL delivery system and to integrate it with the Micrus device. The goal of the project was to develop an integrated minimally-invasive medical device for treating cerebrovascular aneurysms. The device was designed to access aneurysms through commercially-available catheters which are introduced into the patient through a small incision in the leg.« less

NREL/University of Delaware Offshore Wind R&D Collaboration: Cooperative Research and Development Final Report, CRADA Number CRD-10-393

DOE Office of Scientific and Technical Information (OSTI.GOV)

Musial, Walt

2015-11-12

Specifically, the work under this CRADA includes, but is not limited to, the development of test procedures for an offshore test site in Delaware waters; testing of installed offshore wind turbines; performance monitoring of those turbines; and a program of research and development on offshore wind turbine blades, components, coatings, foundations, installation and construction of bottom-fixed structures, environmental impacts, policies, and more generally on means to enhance the reliability, facilitate permitting, and reduce costs for offshore wind turbines. This work will be conducted both at NREL's National Wind Technology Center and participant facilities, as well as the established offshore windmore » test sites.« less

Sugar beet activities of the USDA-ARS East Lansing conducted in cooperation with Saginaw Research & Extension Center during 2013 (including Project 905)

USDA-ARS?s Scientific Manuscript database

Evaluation and rating plots were planted at the Saginaw Valley Research & Extension Center (SVREC) in Frankenmuth, MI in 2013 that focused on Cercospora leaf spot and Rhizoctonia seedling disease performance of a wide range of Beta vulgaris materials. Leaf spot trials were conducted in conjunction w...

Building Diagnostic Market Deployment - Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Katipamula, S.; Gayeski, N.

2012-04-30

also provided validation data sets and the WBE software tool to validate the KGS implementation. OAE diagnostician automatically detects and diagnoses problems with outdoor air ventilation and economizer operation for air handling units (AHUs) in commercial buildings using data available from building automation systems (BASs). As part of this CRADA, PNNL developed implementation documentation and provided technical support to KGS to implement the tool into their software suite. PNNL also provided validation data sets and the OAE software tool to validate the KGS implementation. Finally, as part of this CRADA project, PNNL developed new processes to automate parts of the re-tuning process and transfer those process to KGS for integration into their software product. The transfer of DOE-funded technologies will transform the commercial buildings sector by making buildings more energy efficient and also reducing the carbon footprint from the buildings. As part of the CRADA with PNNL, KGS implemented the whole building energy diagnostician, a portion of outdoor air economizer diagnostician and a number of measures that automate the identification of re-tuning measures.« less

An Investigation into Computer Aided Drafting and Design (CADD) in the Saginaw Area from the Viewpoint of Mechanical Drafting and Design Employers.

ERIC Educational Resources Information Center

Irwin, John L.

The extent to which computer-aided drafting and design (CADD) was being used in local businesses in Saginaw, Michigan, was investigated. Focuses of a literature review were types of CADD systems, categories of CADD users, and the symbiotic relationship between industry and education in providing CADD training. The survey questionnaire was…

Exploring synchrotron radiation capabilities: The ALS-Intel CRADA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gozzo, F.; Cossy-Favre, A; Trippleet, B.

1997-04-01

Synchrotron radiation spectroscopy and spectromicroscopy were applied, at the Advanced Light Source, to the analysis of materials and problems of interest to the commercial semiconductor industry. The authors discuss some of the results obtained at the ALS using existing capabilities, in particular the small spot ultra-ESCA instrument on beamline 7.0 and the AMS (Applied Material Science) endstation on beamline 9.3.2. The continuing trend towards smaller feature size and increased performance for semiconductor components has driven the semiconductor industry to invest in the development of sophisticated and complex instrumentation for the characterization of microstructures. Among the crucial milestones established by themore » Semiconductor Industry Association are the needs for high quality, defect free and extremely clean silicon wafers, very thin gate oxides, lithographies near 0.1 micron and advanced material interconnect structures. The requirements of future generations cannot be met with current industrial technologies. The purpose of the ALS-Intel CRADA (Cooperative Research And Development Agreement) is to explore, compare and improve the utility of synchrotron-based techniques for practical analysis of substrates of interest to semiconductor chip manufacturing. The first phase of the CRADA project consisted in exploring existing ALS capabilities and techniques on some problems of interest. Some of the preliminary results obtained on Intel samples are discussed here.« less

Analysis of recreational land using Skylab data. [Gratiot-Saginaw State Game Area, Michigan

NASA Technical Reports Server (NTRS)

Sattinger, I. J. (Principal Investigator); Sadowski, F. G.; Roller, N. E. G.

1976-01-01

The author has identified the following significant results. S192 data collected on 5 August 1973 were processed by computer to produce a classification map of a part of the Gratiot-Saginaw State Game Area in south central Michigan. A 10-category map was prepared of an area consisting of diverse terrain types, including forests, wetlands, brush, and herbaceous vegetation. An accuracy check indicated that 54% of the pixels were correctly recognized. When these ten scene classes were consolidated to a 5-category map, the accuracy increased to 72%. S190 A, S190 B, and S192 data can be used for regional surveys of existing and potential recreation sites, for delineation of open space, and for preliminary evaluation of geographically extensive sites.

Development of a laser Doppler displacement encoder system with ultra-low-noise-level for linear displacement measurement with subnanometer resolution - Final CRADA Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shu, Deming

An U.S. DOE Cooperative Research and Development Agreement (CRADA) between ANL and Optodyne, Inc. has been established to develop a prototype laser Doppler displacement encoder system with ultra-low noise level for linear measurements to sub-nanometer resolution for synchrotron radiation applications. We have improved the heterodyne efficiency and reduced the detector shot noises by proper shielding and adding a low-pass filter. The laser Doppler displacement encoder system prototype demonstrated a ~ 1 nm system output noise floor with single reflection optics. With multiple-pass optical arrangement, 0.1 nm scale closed-loop feedback control is achieved.

Equipment Only - Solar Resources Measurements at the University of Texas at Austin, TX: Cooperative Research and Development Final Report, CRADA Number CRD-07-222

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stoffel, T.

Faculty and staff at the University of Texas at Austin collected solar resource measurements at their campus using equipment on loan from the National Renewable Energy Laboratory. The equipment was used to train students on the operation and maintenance of solar radiometers and was returned to NREL's Solar Radiation Research Laboratory upon completion of the CRADA. The resulting data augment the solar resource climatology information required for solar resource characterizations in the U.S. The cooperative agreement was also consistent with NREL's goal of developing an educated workforce to advance renewable energy technologies.

National Security Science and Technology Initiative: Air Cargo Screening, Final Report for CRADA Number NFE-07-01081

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bingham, Philip; Bush, John; Bowerman, Biays

The non-intrusive inspection (NII) of consolidated air cargo carried on commercial passenger aircraft continues to be a technically challenging, high-priority requirement of the Department of Homeland Security’s Science and Technology Directorate (DHS S&T), the Transportation Security Agency and the Federal Aviation Administration. The goal of deploying a screening system that can reliably and cost-effectively detect explosive threats in consolidated cargo without adversely affecting the flow of commerce will require significant technical advances that will take years to develop. To address this critical National Security need, the Battelle Memorial Institute (Battelle), under a Cooperative Research and Development Agreement (CRADA) with fourmore » of its associated US Department of Energy (DOE) National Laboratories (Oak Ridge, Pacific Northwest, Idaho, and Brookhaven), conducted a research and development initiative focused on identifying, evaluating, and integrating technologies for screening consolidated air cargo for the presence of explosive threats. Battelle invested $8.5M of internal research and development funds during fiscal years 2007 through 2009.« less

Centralized Cryptographic Key Management and Critical Risk Assessment - CRADA Final Report For CRADA Number NFE-11-03562

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abercrombie, R. K.; Peters, Scott

The Department of Energy Office of Electricity Delivery and Energy Reliability (DOE-OE) Cyber Security for Energy Delivery Systems (CSEDS) industry led program (DE-FOA-0000359) entitled "Innovation for Increasing Cyber Security for Energy Delivery Systems (12CSEDS)," awarded a contract to Sypris Electronics LLC to develop a Cryptographic Key Management System for the smart grid (Scalable Key Management Solutions for Critical Infrastructure Protection). Oak Ridge National Laboratory (ORNL) and Sypris Electronics, LLC as a result of that award entered into a CRADA (NFE-11-03562) between ORNL and Sypris Electronics, LLC. ORNL provided its Cyber Security Econometrics System (CSES) as a tool to be modifiedmore » and used as a metric to address risks and vulnerabilities in the management of cryptographic keys within the Advanced Metering Infrastructure (AMI) domain of the electric sector. ORNL concentrated our analysis on the AMI domain of which the National Electric Sector Cyber security Organization Resource (NESCOR) Working Group 1 (WG1) has documented 29 failure scenarios. The computational infrastructure of this metric involves system stakeholders, security requirements, system components and security threats. To compute this metric, we estimated the stakes that each stakeholder associates with each security requirement, as well as stochastic matrices that represent the probability of a threat to cause a component failure and the probability of a component failure to cause a security requirement violation. We applied this model to estimate the security of the AMI, by leveraging the recently established National Institute of Standards and Technology Interagency Report (NISTIR) 7628 guidelines for smart grid security and the International Electrotechnical Commission (IEC) 63351, Part 9 to identify the life cycle for cryptographic key management, resulting in a vector that assigned to each stakeholder an estimate of their average loss in terms of dollars per day of

Dietary exposure of mink to carp from Saginaw Bay, Michigan: 2. Hematology and liver pathology

USGS Publications Warehouse

Heaton, S. N.; Bursian, S.J.; Giesy, J.P.; Tillitt, D. E.; Render, J. A.; Jones, P.D.; Verbrugge, D.A.; Kubiak, T.J.; Aulerich, R.J.

1995-01-01

The effects of consumption of environmental contaminants contained in carp (Cyprinus carpio)from Saginaw Bay, Michigan on various hematological parameters and liver integrity of adult female mink (Mustela vison) were determined. Mink were fed diets that contained 0 (control), 10, 20, or 40% carp prior to and throughout the reproductive period (182 days). The diets contained 0.015, 0.72, 1.53, and 2.56 mg polychlorinated biphenyls (PCBs)/kg diet and 1.0, 19, 40, and 81 pg 2,3,7,8-tetrachlorodibenzo-p-dioxin equivalents (TEQs)/g diet, respectively. Mink fed the diets containing carp showed a general dose-dependent occurrence of clinical signs commonly associated with chlorinated hydrocarbon toxicity, including listlessness, nervousness when approached, anorexia, and melena. Erythrocyte counts were less in mink exposed to Saginaw Bay carp than in controls, while the number of white blood cells was greater than in controls. Significant differences (p<0.05) in the concentrations of neutrophils, lymphocytes, monocytes, and eosinophils were also found between the control and carp-fed groups, but are considered to be of limited clinical or biological importance. Hematocrit values for the mink fed the 20 and 40% carp diets were significantly less than those of mink in the control and 10% carp groups. There were no significant differences in hemoglobin concentrations among the groups. Necropsies revealed enlarged yellowish livers in many of the carp-fed mink, especially those fed the 40% carp diet. Liver, spleen, and lung weights of carp-fed mink were significantly greater than those of control mink. Histopathologic examination of the livers revealed various degrees of congestion, hepatocellular fatty changes, and scattered portal lymphocytic infiltration which were most prevalent in mink fed the carp diets. These clinical signs, hematological effects, and histologic alterations are similar to those previously described for chlorinated hydrocarbon toxicoses in mink.

School-to-Work Opportunities Local Partnership Implementation Grant, 1994-96. Final Report. Evaluation Report.

ERIC Educational Resources Information Center

Claus, Richard N.; And Others

The 5-year School-to-Work (STW) Opportunities project of the School District of Saginaw, Michigan, was implemented through the Manufacturing, Engineering, Construction, and Automotive (MECA) partnership. Housed at the district's Saginaw Career Complex, it included collaboration among Career Complex staff and local business representatives in the…

78 FR 42532 - Cooperative Research and Development Agreement (CRADA) Opportunity With the Department of...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-16

... DEPARTMENT OF HOMELAND SECURITY Cooperative Research and Development Agreement (CRADA) Opportunity With the Department of Homeland Security for the Development of a Foot-and-Mouth Disease 3ABC ELISA... in developing and validating an ELISA diagnostic kit for detection of Foot and Mouth Disease Virus...

Development of a General-Purpose Analysis System Based on a Programmable Fluid Processor Final Report CRADA No. TC-2027-01

DOE Office of Scientific and Technical Information (OSTI.GOV)

McConaghy, C. F.; Gascoyne, P. R.

The purpose ofthis project was to develop a general-purpose analysis system based on a programmable fluid processor (PFP). The PFP is an array of electrodes surrounded by fluid reservoirs and injectors. Injected droplets of various reagents are manjpulated and combined on the array by Dielectrophoretic (DEP) forces. The goal was to create a small handheld device that could accomplish the tasks currently undertaken by much larger, time consuming, manual manipulation in the lab. The entire effo1t was funded by DARPA under the Bio-Flips program. MD Anderson Cancer Center was the PI for the DARPA effort. The Bio-Flips program was amore » 3- year program that ran from September 2000 to September 2003. The CRADA was somewhat behind the Bi-Flips program running from June 2001 to June 2004 with a no cost extension to September 2004.« less

Final Report of a CRADA Between Pacific Northwest National Laboratory and the Ford Motor Company (CRADA No. PNNL/265): “Deactivation Mechanisms of Base Metal/Zeolite Urea Selective Catalytic Reduction Materials, and Development of Zeolite-Based Hydrocarbon Adsorber Materials”

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gao, Feng; Kwak, Ja Hun; Lee, Jong H.

2013-02-14

found in the engine exhaust. For these reasons, automakers and engine manufacturers have difficulty improving their catalytic converters for meeting the stringent HC emission standards. In this collaborative program, scientists and engineers in the Institute for Integrated Catalysis at Pacific Northwest National Laboratory and at Ford Motor Company have investigated laboratory- and engine-aged SCR catalysts, containing mainly base metal zeolites. These studies are leading to a better understanding of various aging factors that impact the long-term performance of SCR catalysts and improve the correlation between laboratory and engine aging, saving experimental time and cost. We have also studied materials effective for the temporary storage of HC species during the cold-start period. In particular, we have examined the adsorption and desorption of various HC species produced during the combustion with different fuels (e.g., gasoline, E85, diesel) over potential HC adsorber materials, and measured the kinetic parameters to update Ford’s HC adsorption model. Since this CRADA has now been completed, in this final report we will provide brief summaries of most of the work carried out on this CRADA over the last several years.« less

Particulate Emissions Control using Advanced Filter Systems: Final Report for Argonne National Laboratory, Corning Inc. and Hyundai Motor Company CRADA Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seong, Hee Je; Choi, Seungmok

2015-10-09

This is a 3-way CRADA project working together with Corning, Inc. and Hyundai Motor Co. (HMC). The project is to understand particulate emissions from gasoline direct-injection engines (GDI) and their physico-chemical properties. In addition, this project focuses on providing fundamental information about filtration and regeneration mechanisms occurring in gasoline particulate filter (GPF) systems. For the work, Corning provides most advanced filter substrates for GPF applications and HMC provides three-way catalyst (TWC) coating services of these filter by way of a catalyst coating company. Then, Argonne National Laboratory characterizes fundamental behaviors of filtration and regeneration processes as well as evaluated TWCmore » functionality for the coated filters. To examine aging impacts on TWC and GPF performance, the research team evaluates gaseous and particulate emissions as well as back-pressure increase with ash loading by using an engine-oil injection system to accelerate ash loading in TWC-coated GPFs.« less

High Specific Stiffness Shafts and Advanced Bearing Coatings for Gas Turbine Engines Final Report CRADA No. TC-1089-95

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barbee, Troy; Chin, Herbert

At the time of the CRADA, the largest in-service gas-turbine aircraft engines strove for increased thrust and power density to meet the requirements for take-off thrust, given the increase in take-off gross weight (TOGW) associated with longer range transport requirements. The trend in modem turbo shaft engines was toward turbine shafts with higher and higher length-to-diameter ratios, which reduced the shaft critical speed. Using co nventional shaft materials, this lead to shafts that needed to operate near or above sensitive shaft bending critical speeds, therefore requiring multiple bearings and/ or multiple squeeze-film dampers to control the dynamic response. Using newmore » materials and d esign concepts this project demonstrated the use of new shaft materials which could provide increased shaft speed range above existing maximum engine speeds without encountering a critic al speed event and high vector deflections. This increased main shaft speed also resulted in decreased bearing life associated with lower heat dissipation and higher centrifugal forces. Thus, a limited effort was devoted to feasibility of higher performance bearing coatings to mitigate the speed effects.« less

Spatial variations in the incidence of breast cancer and potential risks associated with soil dioxin contamination in Midland, Saginaw, and Bay Counties, Michigan, USA

PubMed Central

Dai, Dajun; Oyana, Tonny J

2008-01-01

Background High levels of dioxins in soil and higher-than-average body burdens of dioxins in local residents have been found in the city of Midland and the Tittabawassee River floodplain in Michigan. The objective of this study is threefold: (1) to evaluate dioxin levels in soils; (2) to evaluate the spatial variations in breast cancer incidence in Midland, Saginaw, and Bay Counties in Michigan; (3) to evaluate whether breast cancer rates are spatially associated with the dioxin contamination areas. Methods We acquired 532 published soil dioxin data samples collected from 1995 to 2003 and data pertaining to female breast cancer cases (n = 4,604) at ZIP code level in Midland, Saginaw, and Bay Counties for years 1985 through 2002. Descriptive statistics and self-organizing map algorithm were used to evaluate dioxin levels in soils. Geographic information systems techniques, the Kulldorff's spatial and space-time scan statistics, and genetic algorithms were used to explore the variation in the incidence of breast cancer in space and space-time. Odds ratio and their corresponding 95% confidence intervals, with adjustment for age, were used to investigate a spatial association between breast cancer incidence and soil dioxin contamination. Results High levels of dioxin in soils were observed in the city of Midland and the Tittabawassee River 100-year floodplain. After adjusting for age, we observed high breast cancer incidence rates and detected the presence of spatial clusters in the city of Midland, the confluence area of the Tittabawassee, and Saginaw Rivers. After accounting for spatiotemporal variations, we observed a spatial cluster of breast cancer incidence in Midland between 1985 and 1993. The odds ratio further suggests a statistically significant (α = 0.05) increased breast cancer rate as women get older, and a higher disease burden in Midland and the surrounding areas in close proximity to the dioxin contaminated areas. Conclusion These findings suggest that

Plug-and -Play Model Architecture and Development Environment for Powertrain/Propulsion System - Final CRADA Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rousseau, Aymeric

2013-02-01

Several tools already exist to develop detailed plant model, including GT-Power, AMESim, CarSim, and SimScape. The objective of Autonomie is not to provide a language to develop detailed models; rather, Autonomie supports the assembly and use of models from design to simulation to analysis with complete plug-and-play capabilities. Autonomie provides a plug-and-play architecture to support this ideal use of modeling and simulation for math-based automotive control system design. Models in the standard format create building blocks, which are assembled at runtime into a simulation model of a vehicle, system, subsystem, or component to simulate. All parts of the graphical usermore » interface (GUI) are designed to be flexible to support architectures, systems, components, and processes not yet envisioned. This allows the software to be molded to individual uses, so it can grow as requirements and technical knowledge expands. This flexibility also allows for implementation of legacy code, including models, controller code, processes, drive cycles, and post-processing equations. A library of useful and tested models and processes is included as part of the software package to support a full range of simulation and analysis tasks, immediately. Autonomie also includes a configuration and database management front end to facilitate the storage, versioning, and maintenance of all required files, such as the models themselves, the model’s supporting files, test data, and reports. During the duration of the CRADA, Argonne has worked closely with GM to implement and demonstrate each one of their requirements. A use case was developed by GM for every requirement and demonstrated by Argonne. Each of the new features were verified by GM experts through a series of Gate. Once all the requirements were validated they were presented to the directors as part of GM Gate process.« less

Concepts for the Design of a Diagnostic Device to Detect Malignancies in Human Tissues Final Report CRADA No. TSB-2023-00

DOE Office of Scientific and Technical Information (OSTI.GOV)

DaSilva, L.; Marion, J.; Chase, C.

BioLuminate, Inc. planned to develop, produce and market a revolutionary diagnostic device for early breast cancer diagnosis. The device was originally invented by NASA; and exclusively licensed to BioLuminate for commercialization. At the time of the CRADA, eighty-five percent (85%) of all biopsies in the United States were found negative each year. The number of biopsies cost the health care system $23 billio n annually. A multi-sensor probe would allow surgeons to improve breast cancer scre ening and significantly reduce the number of biopsies. BioLuminate was developing an in-vivo system for the detection of cancer using a multi-sensor needle/probe. Themore » first system would be developed for the detection of breast cancer. LLNL, in collaboration with BioLuminate worked toward a detailed concept specification for the prototype multi-sensor needle/probe suitable for breast cancer analysis. BioLuminate in collaboration with LLNL, worked to develop a new version of the needle probe that would be the same size as needles commonly used to draw blood.« less

Reconciling Basin-Scale Top-Down and Bottom-Up Methane Emission Measurements for Onshore Oil and Gas Development: Cooperative Research and Development Final Report, CRADA Number CRD-14-572

DOE Office of Scientific and Technical Information (OSTI.GOV)

Heath, Garvin A.

The overall objective of the Research Partnership to Secure Energy for America (RPSEA)-funded research project is to develop independent estimates of methane emissions using top-down and bottom-up measurement approaches and then to compare the estimates, including consideration of uncertainty. Such approaches will be applied at two scales: basin and facility. At facility scale, multiple methods will be used to measure methane emissions of the whole facility (controlled dual tracer and single tracer releases, aircraft-based mass balance and Gaussian back-trajectory), which are considered top-down approaches. The bottom-up approach will sum emissions from identified point sources measured using appropriate source-level measurement techniquesmore » (e.g., high-flow meters). At basin scale, the top-down estimate will come from boundary layer airborne measurements upwind and downwind of the basin, using a regional mass balance model plus approaches to separate atmospheric methane emissions attributed to the oil and gas sector. The bottom-up estimate will result from statistical modeling (also known as scaling up) of measurements made at selected facilities, with gaps filled through measurements and other estimates based on other studies. The relative comparison of the bottom-up and top-down estimates made at both scales will help improve understanding of the accuracy of the tested measurement and modeling approaches. The subject of this CRADA is NREL's contribution to the overall project. This project resulted from winning a competitive solicitation no. RPSEA RFP2012UN001, proposal no. 12122-95, which is the basis for the overall project. This Joint Work Statement (JWS) details the contributions of NREL and Colorado School of Mines (CSM) in performance of the CRADA effort.« less

Improving Translation Models for Predicting the Energy Yield of Photovoltaic Power Systems. Cooperative Research and Development Final Report, CRADA Number CRD-13-526

DOE Office of Scientific and Technical Information (OSTI.GOV)

Emery, Keith

2015-08-04

The project under this CRADA will analyze field data of various flat-plate and concentrator module technologies and cell measurements at the laboratory level. The field data will consist of current versus voltage data collected over many years on a latitude tilt test bed for Si, CdTe, amorphous silicon, and CIGS technologies. The concentrator data will be for mirror- and lens-based module designs using multijunction cells. The laboratory data will come from new measurements of cell performance with systematic variation of irradiance, temperature and spectral composition. These measurements will be labor-intensive and the aim will be to cover the widest possiblemore » parameter space for as many different PV samples as possible. The data analysis will require software tools to be developed. These tools will be customized for use with the specific NREL datasets and will be unsuitable for commercial release. The tools will be used to evaluate different translation equations against NREL outdoor datasets.« less

Development of a High Volume Capable Process to Manufacture High Performance Photovoltaic Cells: Cooperative Research and Development Final Report, CRADA Number CRD-08-322

DOE Office of Scientific and Technical Information (OSTI.GOV)

Geisz, J. F.

2012-11-01

The intent of the work is for RFMD and NREL to cooperate in the development of a commercially viable and high volume capable process to manufacture high performance photovoltaic cells, based on inverted metamorphic (IMM) GaAs technology. The successful execution of the agreement will result in the production of a PV cell using technology that is capable of conversion efficiency at par with the market at the time of release (reference 2009: 37-38%), using RFMD's production facilities. The CRADA work has been divided into three phases: (1) a foundation phase where the teams will demonstrate the manufacturing of a basicmore » PV cell at RFMD's production facilities; (2) a technology demonstration phase where the teams will demonstrate the manufacturing of prototype PV cells using IMM technology at RFMD's production facilities, and; (3) a production readiness phase where the teams will demonstrate the capability to manufacture PV cells using IMM technology with high yields, high reliability, high reproducibility and low cost.« less

Advanced variable speed air source integrated heat pump (AS-IHP) development - CRADA final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baxter, Van D.; Rice, C. Keith; Munk, Jeffrey D.

2015-09-30

Between August 2011 and September 2015, Oak Ridge National Laboratory (ORNL) and Nordyne, LLC (now Nortek Global HVAC LLC, NGHVAC) engaged in a Cooperative Research and Development Agreement (CRADA) to develop an air-source integrated heat pump (AS-IHP) system for the US residential market. Two generations of laboratory prototype systems were designed, fabricated, and lab-tested during 2011-2013. Performance maps for the system were developed using the latest research version of the DOE/ORNL Heat Pump Design Model, or HPDM, (Rice 1991; Rice and Jackson 2005; Shen et al 2012) as calibrated against the lab test data. These maps were the input tomore » the TRNSYS (SOLAR Energy Laboratory, et al, 2010) system to predict annual performance relative to a baseline suite of equipment meeting minimum efficiency standards in effect in 2006 (combination of 13 SEER air-source heat pump (ASHP) and resistance water heater with Energy Factor (EF) of 0.9). Predicted total annual energy savings, while providing space conditioning and water heating for a tight, well insulated 2600 ft2 (242 m2) house at 5 U.S. locations, ranged from 46 to 61%, averaging 52%, relative to the baseline system (lowest savings at the cold-climate Chicago location). Predicted energy use for water heating was reduced 62 to 76% relative to resistance WH. Based on these lab prototype test and analyses results a field test prototype was designed and fabricated by NGHVAC. The unit was installed in a 2400 ft2 (223 m2) research house in Knoxville, TN and field tested from May 2014 to April 2015. Based on the demonstrated field performance of the AS-IHP prototype and estimated performance of a baseline system operating under the same loads and weather conditions, it was estimated that the prototype would achieve ~40% energy savings relative to the minimum efficiency suite. The estimated WH savings were >60% and SC mode savings were >50%. But estimated SH savings were only about 20%. It is believed that had the

Production of a water quality map of Saginaw Bay by computer processing of LANDSAT-2 data

NASA Technical Reports Server (NTRS)

Mckeon, J. B.; Rogers, R. H.; Smith, V. E.

1977-01-01

Surface truth and LANDSAT measurements collected July 31, 1975, for Saginaw Bay were used to demonstrate a technique for producing a color coded water quality map. On this map, color was used as a code to quantify five discrete ranges in the following water quality parameters: (1) temperature, (2) Secchi depth, (3) chloride, (4) conductivity, (5) total Kjeldahl nitrogen, (6) total phosphorous, (7)chlorophyll a, (8) total solids and (9) suspended solids. The LANDSAT and water quality relationship was established through the use of a set of linear regression equations where the water quality parameters are the dependent variables and LANDSAT measurements are the independent variables. Although the procedure is scene and surface truth dependent, it provides both a basis for extrapolating water quality parameters from point samples to unsampled areas and a synoptic view of water mass boundaries over the 3000 sq. km bay area made from one day's ship data that is superior, in many ways, to the traditional machine contoured maps made from three day's ship data.

Mink liver TEQs and reproductive NOAEL resulting from dietary exposure to fish from Saginaw Bay

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tillitt, D.E.; Gale, R.W.; Peterman, P.H.

1994-12-31

Mink are known to be very sensitive to the toxic effects of planar halogenated hydrocarbons (PHHs). Previously the authors reported the reproductive effects in mink fed a diet containing 10, 20, or 40% fish taken from Saginaw Bay, Lake Huron. In this presentation the authors report the complete chemical analyses of the diets and the adult mink livers, along with a comparison of an additive model of toxicity with the results of the H411E bioassay on these samples. The H411E bioassay consistently estimated greater dioxin toxic-equivalents (TEQS) as compared to an additive model of toxicity and chemical analyses. TEQs derivedmore » from chemical analyses accounted for approximately 60% of the TEQs observed with the H411E bioassay. The difference is likely due to the presence of compounds which were not quantitated as opposed to synergistic interactions of the mixtures. Significant reproductive effects were observed in the lowest treatment group (10% fish, or 19.4 pg TEQs/g). The implications of these chemical and bioassay analyses on the calculation of a NOAEL will be discussed.« less

Equipment Loan for Concentrated PV Cavity Converter (PVCC) Research: Cooperative Research and Development Final Report, CRADA Number CRD-08-285

DOE Office of Scientific and Technical Information (OSTI.GOV)

Netter, Judy

2015-07-28

Interest in High Concentration Photovoltaics (HCPV) for terrestrial applications has significantly grown in recent years. A major driver behind this growth trend is the availability of high efficiency multi-junction (MJ) cells that promise reliable operation under high concentrations (500 to 1000 suns). The primary impact of HCPV on the solar electricity cost is the dramatic reduction in cell cost. For terrestrial HCPV systems, operating at concentrations ≥ 500 suns, the expensive MJ cells are marginally affordable. Most recently, triple-junction test cells have achieved a conversion efficiency of over 40% under concentrated sunlight. Photovoltaic Cavity Converter (PVCC) is a multi-bandgap, highmore » concentration PV device developed by United Innovations, Inc., under subcontract to NREL. The lateral- (2- dimensional) structure of PVCC, as opposed to vertical multi-junction (MJ) structure, helps to circumvent most of the developmental challenges MJ technology has yet to overcome. This CRADA will allow the continued development of this technology by United Innovations. This project was funded by the California Energy Commission and is the second phase of a twopart demonstration program. The key advantage of the design was the use of a PVCC as the receiver. PVCCs efficiently process highly concentrated solar radiation into electricity by recycling photons that are reflected from the surface of the cells. Conventional flat, twodimensional receivers cannot recycle photons and the reflected photons are lost to the conversion process.« less

Plug and Play Solar Power: Simplifying the Integration of Solar Energy in Hybrid Applications; Cooperative Research and Development Final Report, CRADA Number CRD-13-523

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lundstrom, Blake R.

The Commonwealth Scientific and Industrial Research Organisation (CSIRO) is Australia's national science agency. CSIRO received funding from the Australian Solar Institute (ASI) for the United States-Australia Solar Energy Collaboration (USASEC) project 1-USO032 Plug and Play Solar Power: Simplifying the Integration of Solar Energy in Hybrid Applications (Broader Project). The Australian Solar Institute (ASI) operated from August 2009 to December 2012 before being merged into the Australian Renewable Energy Agency (ARENA). The Broader Project sought to simplify the integration, accelerate the deployment, and lower the cost of solar energy in hybrid distributed generation applications by creating plug and play solar technology.more » CSIRO worked with the National Renewable Energy Laboratory (NREL) as set out in a Joint Work Statement to review communications protocols relevant to plug-and-play technology and perform prototype testing in its Energy System Integration Facility (ESIF). For the avoidance of doubt, this CRADA did not cover the whole of the Broader Project and only related to the work described in the Joint Work Statement, which was carried out by NREL.« less

Comparing polychlorinated biphenyl concentrations and patterns in the Saginaw River using sediment, caged fish, and semipermeable membrane devices

USGS Publications Warehouse

Echols, K.R.; Gale, R.W.; Schwartz, T.R.; Huckins, J.N.; Williams, L.L.; Meadows, J.C.; Morse, D.; Petty, J.D.; Orazio, C.E.; Tillitt, D.E.

2000-01-01

Three techniques of assessing bioavailable polychlorinated biphenyls (PCBs) in the Saginaw River, MI, were compared: sediments, caged fish, and semipermeable membrane devices (SPMDs). SPMDs and caged fish were placed in the river for 28 days at five sites where sediments were also sampled. The samples were analyzed for PCB congeners to determine concentrations and patterns. Total PCB concentrations ranged from 33 to 280 ng/g (dry weight) in sediments, 46 to 290 ng/g (wet weight) in caged fish, and 77 to 790 ng/g in SPMDs. Previously reported rates of PCB accumulation by SPMDs were used to estimate aqueous concentrations from the PCB concentrations detected in the SPMDs. Sediment-water partition coefficients were used to estimate aqueous PCB concentrations from sediment. Steady-state bioconcentration factors and depuration rate constants were used to estimate dissolved PCB concentrations from caged channel catfish. Relative PCB patterns from the SPMDs, caged fish, and sediment were compared using principal components analysis. SPMD and sediment samples provide complementary information. Sediments reflect long-term accumulation and weathering, while SPMDs integrate water concentrations only during the sampling period. Because of higher water solubilities of lower-chlorinated PCBs these predominate in the SPMDs as compared to in the fish and sediments. Contaminant profile differences between caged fish and SPMDs are likely due to metabolism and depuration of certain PCB congeners by fish.Three techniques of assessing bioavailable polychlorinated biphenyls (PCBs) in the Saginaw River, Ml, were compared: sediments, caged fish, and semipermeable membrane devices (SPMDs). SPMDs and caged fish were placed in the river for 28 days at five sites where sediments were also sampled. The samples were analyzed for PCB congeners to determine concentrations and patterns. Total PCB concentrations ranged from 33 to 280 ng/g (dry weight) in sediments, 46 to 290 ng/g (wet weight) in

Application of LANDSAT to the surveillance and control of lake eutrophication in the Great Lakes basin. [Saginaw Bay, Michigan and Wisconsin

NASA Technical Reports Server (NTRS)

Rogers, R. H. (Principal Investigator)

1976-01-01

The author has identified the following significant results. Computer techniques were developed for mapping water quality parameters from LANDSAT data, using surface samples collected in an ongoing survey of water quality in Saginaw Bay. Chemical and biological parameters were measured on 31 July 1975 at 16 bay stations in concert with the LANDSAT overflight. Application of stepwise linear regression bands to nine of these parameters and corresponding LANDSAT measurements for bands 4 and 5 only resulted in regression correlation coefficients that varied from 0.94 for temperature to 0.73 for Secchi depth. Regression equations expressed with the pair of bands 4 and 5, rather than the ratio band 4/band 5, provided higher correlation coefficients for all the water quality parameters studied (temperature, Secchi depth, chloride, conductivity, total kjeldahl nitrogen, total phosphorus, chlorophyll a, total solids, and suspended solids).

NREL and DONG Energy Collaboration for Grid Simulator Controls and Testing: Cooperative Research and Development Final Report, CRADA Number CRD-13-527

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gevorgian, Vahan

The National Renewable Energy Laboratory (NREL) and DONG Energy are interested in collaborating for the development of control algorithms, modeling, and grid simulator testing of wind turbine generator systems involving NWTC's advanced Controllable Grid Interface (CGI). NREL and DONG Energy will work together to develop control algorithms, models, test methods, and protocols involving NREL's CGI, as well as appropriate data acquisition systems for grid simulation testing. The CRADA also includes work on joint publication of results achieved from modeling and testing efforts. Further, DONG Energy will send staff to NREL on a long-term basis for collaborative work including modeling andmore » testing. NREL will send staff to DONG Energy on a short-term basis to visit wind power sites and participate in meetings relevant to this collaborative effort. DOE has provided NREL with over 10 years of support in developing custom facilities and capabilities to enable testing of full-scale integrated wind turbine drivetrain systems in accordance with the needs of the US wind industry. NREL currently operates a 2.5MW dynamometer and is in the processes of commissioning a 5MW dynamometer and a grid simulator (referred to as a 'Controllable Grid Interface' or CGI). DONG Energy is the market leader in offshore wind power development, with currently over 1 GW of on- and offshore wind power in operation, and 1.3 GW under construction. DONG Energy has on-going R&D projects involving high voltage DC (HVDC) transmission.« less

CRADA Final Report: Application of Dual-Mode Inverter Control to Commercially Available Radial-Gap Mermanent Magnet Motors - Vol. I

DOE Office of Scientific and Technical Information (OSTI.GOV)

McKeever, John W; Lawler, Jack; Downing, Mark

2006-05-01

John Deere and Company (Deere), their partner, UQM Technologies, Inc. (UQM), and the Oak Ridge National Laboratory's (ORNL's) Power Electronics and Electric Machinery Research Center (PEEMRC) recently completed work on the cooperative research and development agreement (CRADA) Number ORNL 04-0691 outlined in this report. CRADA 04-0691 addresses two topical issues of interest to Deere: (1) Improved characterization of hydrogen storage and heat-transfer management; and (2) Potential benefits from advanced electric motor traction-drive technologies. This report presents the findings of the collaborative examination of potential operational and cost benefits from using ORNL/PEEMRC dual-mode inverter control (DMIC) to drive permanent magnet (PM)more » motors in applications of interest to Deere. DMIC was initially developed and patented by ORNL to enable PM motors to be driven to speeds far above base speed where the back-electromotive force (emf) equals the source voltage where it is increasingly difficult to inject current into the motor. DMIC is a modification of conventional phase advance (CPA). DMIC's dual-speed modes are below base speed, where traditional pulse-width modulation (PWM) achieves maximum torque per ampere (amp), and above base speed, where six-step operation achieves maximum power per amp. The modification that enables DMIC adds two anti-parallel thyristors in each of the three motor phases, which consequently adds the cost of six thyristors. Two features evaluated in this collaboration with potential to justify the additional thyristor cost were a possible reduction in motor cost and savings during operation because of higher efficiency, both permitted because of lower current. The collaborative analysis showed that the reduction of motor cost and base cost of the inverter was small, while the cost of adding six thyristors was greater than anticipated. Modeling the DMIC control displayed inverter efficiency gains due to reduced current, especially

Enhanced control & sensing for the REMOTEC ANDROS Mk VI robot. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spelt, P.F.; Harvey, H.W.

1997-08-01

This Cooperative Research and Development Agreement (CRADA) between Lockheed Marietta Energy Systems, Inc., and REMOTEC, Inc., explored methods of providing operator feedback for various work actions of the ANDROS Mk VI teleoperated robot. In a hazardous environment, an extremely heavy workload seriously degrades the productivity of teleoperated robot operators. This CRADA involved the addition of computer power to the robot along with a variety of sensors and encoders to provide information about the robot`s performance in and relationship to its environment. Software was developed to integrate the sensor and encoder information and provide control input to the robot. ANDROS Mkmore » VI robots are presently used by numerous electric utilities to perform tasks in reactors where substantial exposure to radiation exists, as well as in a variety of other hazardous environments. Further, this platform has potential for use in a number of environmental restoration tasks, such as site survey and detection of hazardous waste materials. The addition of sensors and encoders serves to make the robot easier to manage and permits tasks to be done more safely and inexpensively (due to time saved in the completion of complex remote tasks). Prior research on the automation of mobile platforms with manipulators at Oak Ridge National Laboratory`s Center for Engineering Systems Advanced Research (CESAR, B&R code KC0401030) Laboratory, a BES-supported facility, indicated that this type of enhancement is effective. This CRADA provided such enhancements to a successful working teleoperated robot for the first time. Performance of this CRADA used the CESAR laboratory facilities and expertise developed under BES funding.« less

CRADA opportunities with METC`s gasification and hot gas cleanup facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Galloway, E N; Rockey, J M; Tucker, M S

1995-06-01

Opportunities exist for Cooperative Research and Development Agreements (CRADA) at the Morgantown Energy Technology Center (METC) to support commercialization of IGCC power systems. METC operates an integrated gasifier and hot gas cleanup facility for the development of gasification and hot gas cleanup technologies. The objective of our program is to gather performance data on gasifier operation, particulate removal, desulfurization and regeneration technologies. Additionally, slip streams are provided for developing various technologies such as; alkali monitoring, particulate measuring, chloride removal, and contaminate recovery processes. METC`s 10-inch diameter air blown Fluid Bed Gasifier (FBG) provides 300 lb/hr of coal gas at 1100{degrees}Fmore » and 425 psig. The particulate laden gas is transported to METC`s Modular Gas Cleanup Rig (MGCR). The gas pressure is reduced to 285 psig before being fed into a candle filter vessel. The candle filter vessel houses four candle filters and multiple test coupons. The particulate free gas is then desulfurized in a sorbent reactor. Starting in 1996 the MGCR system will be able to regenerate the sorbent in the same vessel.« less

Dietary exposure of mink to carp from Saginaw Bay, Michigan. 1. Effects on reproduction and survival, and the potential risks to wild mink populations

USGS Publications Warehouse

Heaton, S. N.; Bursian, S.J.; Giesy, J.P.; Tillitt, D. E.; Render, J. A.; Jones, P.D.; Verbrugge, D.A.; Kubiak, T.J.; Aulerich, R.J.

1995-01-01

Carp (Cyprinus carpio) collected from Saginaw Bay, Michigan, containing 8.4 mg total polychlorinated biphenyls (PCBs)/kg and 194 ng of 2,3,7,8-tetrachloro-dibenzo-p-dioxin equivalents (TEQs)/kg, were substituted for marine fish at levels of 0, 10, 20, or 40% in the diets of adult ranch mink (Mustela vison). The diets, containing 0.015, 0.72, 1.53, and 2.56 mg PCBs/kg diet, or 1.03, 19.41, 40.02, and 80.76 ng TEQs/kg diet, respectively, were fed to mink prior to and throughout the reproductive period to evaluate the effects of a naturally-contaminated prey species on their survival and reproductive performance. The total quantities of PCBs ingested by the mink fed 0, 10, 20, or 40% carp over the 85-day treatment period were 0.34, 13.2, 25.3, and 32.3 mg PCBs/mink, respectively. The corresponding quantities of TEQs ingested by the mink over the same treatment period were 23, 356, 661, and 1,019 ng TEQs/mink, respectively. Consumption of feed by mink was inversely proportional to the PCB and TEQ content of the diet. The diets containing Saginaw Bay carp caused impaired reproduction and/or reduced survival of the kits. Compared to controls, body weights of kits at birth were significantly reduced in the 20 and 40% carp groups, and kit body weights and survival in the 10 and 20% carp groups were significantly reduced at three and six weeks of age. The females fed 40% carp whelped the fewest number of kits, all of which were stillborn or died within 24 hours. Lowest observable adverse effect levels (LOAEL) of 0.134 mg PCBs/kg body weight/day or 3.6 ng TEQs/kg body weight/day for adult female mink were determined. The potential effects of exposure of wild mink to contaminated Great Lakes fish were assessed by calculating “maximum allowable daily intakes” and “hazard indices” based on total concentrations of PCB residues in several species of Great Lakes fish and mink toxicity data derived from the study.

Caspian tern reproduction in the Saginaw Bay ecosystem following a 100-year flood event

USGS Publications Warehouse

Ludwig, James P.; Auman, Heidi J.; Kurita, Hiroko; Ludwig, Matthew E.; Campbell, Loraine M.; Giesy, John P.; Tillitt, Donald E.; Jones, Paul; Yamashita, Nobu; Tanabe, Shinsuke; Tatsukawa, Ryo

1993-01-01

In the 2 years that followed the 100-year flood incident of September 1986 in the Saginaw River/Bay ecosystem, the reproduction of Caspian terns collapsed and then slowly recovered. Egg viability and fledging rates of hatched chicks were drastically depressed in 1987 and 1988. Eggs from clutches laid later in the year were less viable and chicks hatched from these eggs displayed wasting syndromes and deformities. The post-flood rate of deformities in hatched chicks in 1987–1989 was 163-fold greater than background rates for this population in 1962–1967. Embryonic abnormalities and deformities were found in many embryos recovered from dead eggs. Recently published data on planar toxic chemicals from samples of forage fish, tern eggs, and chicks from water birds nesting in the bay implicate planar dioxin-like PCBs 77 and 126 as the sources of these severe bioeffects. The planar PCB congeners accounted for >98% of TCDD-EQ toxicity in the tern eggs, and several were present at levels near or at the LD95 levels each for chicken eggs. Actual TCDD was about 1% of the TCDD-EQ toxicity. Very rapid buildup rates of PCBs were measured in tern eggs. The calculated toxic potency of PCB recovered from tern eggs was about 15-fold greater than parent aroclor 1242 PCB. Smaller tern species were projected to be much more at risk than the larger Caspian tern due to greater standard metabolic rates. The study supports the view that sediment disturbance and sediment banks of toxic chemicals are major threats to upper trophic level fish-eating species.

Predictive Engineering Tools for Injection-Molded Long-Carbon-Fiber Thermoplastic Composites - FY13 Fourth Quarterly Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nguyen, Ba Nghiep; Simmons, Kevin L.

2013-12-02

This quarterly report summarizes the status of the project planning to obtain all the approvals required for a Cooperative Research and Development Agreement (CRADA) with Autodesk, Inc., Toyota Motor Engineering and Manufacturing North America (Toyota), and Magna Exterior and Interiors Corporation (Magna). The final CRADA documents processed by PNNL’s Legal Services were submitted to all the parties for signatures.

New Materials for Electric Drive Vehicles - Final CRADA Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carter, J. David

This project was sponsored by the US DOE Global Initiatives for Proliferation Prevention. The object was for Ukrainian and US partners, including Argonne, AETC, and Dontech to develop special carbon materials and factory production equipment with the goal of making better car batteries to achieve DOE's goals for all-electric and plug-in hybrid electric vehicles. Carbon materials are used in designs for lithium-ion batteries and metal-air batteries, both leading contenders for future electric cars. Specifically, the collaborators planned to use the equipment derived from this project to develop a rechargeable battery system that will use the carbon materials produced by themore » innovative factory process equipment. The final outcome of the project was that the Ukrainian participants consisting of the Kharkov Institute of Physics and Technology (KIPT), the Institute of Gas of National Academy of Sciences of Ukraine and the Materials Research Center, Ltd. designed, built, tested and delivered 14 pieces of processing equipment for pilot scale carbon production lines at the AETC, Arlington Heights facilities. The pilot scale equipment will be used to process materials such as activated carbon, thermally expanded graphite and carbon coated nano-particles. The equipment was shipped from Ukraine to the United States and received by AETC on December 3, 2013. The equipment is on loan from Argonne, control # 6140. Plug-in hybrid electric vehicles (PHEV) and all-electric vehicles have already demostrated success in the U.S. as they begin to share the market with older hybrid electric designs. When the project was conceived, PHEV battery systems provided a ~40 mile driving range (2011 figures). DOE R&D targets increased this to >100 miles at reduced cost less than $250/kWh (2011 figures.) A 2016 Tesla model S has boasted 270 miles. The project object was to develop pilot-production line equipment for advanced hybrid battery system that achieves cycle life of 1000, an energy

Final Report on the Performance of the Eichrom Technologies Procept® Rapid Dioxin Assay for Soil and Sediment Samples

EPA Science Inventory

A demonstration of screening technologies for determining the presence of dioxin and dioxin-like compounds in soil and sediment was conducted under the U.S. Environmental Protection Agency’s (EPA’s) Superfund Innovative Technology Evaluation Program in Saginaw, Michigan in 2004. ...

Simulated effects of pumping irrigation wells on ground-water levels in western Saginaw County, Michigan

USGS Publications Warehouse

Hoard, Christopher J.; Westjohn, David B.

2001-01-01

Success of agriculture in many areas of Michigan relies on withdrawal of large quantities of ground water for irrigation. In some areas of the State, water-level declines associated with large ground-water withdrawals may adversely affect nearby residential wells. Residential wells in several areas of Saginaw County, in Michigan's east-central Lower Peninsula, recently went dry shortly after irrigation of crop lands commenced; many of these wells also went dry during last year's agricultural cycle (summer 2000). In September 2000, residential wells that had been dry returned to function after cessation of pumping from large-capacity irrigation wells. To evaluate possible effects of groundwater withdrawals from irrigation wells on residential wells, the U.S. Geological Survey used hydrogeologic data including aquifer tests, water-level records, geologic logs, and numerical models to determine whether water-level declines and the withdrawal of ground water for agricultural irrigation are related. Numerical simulations based on representative irrigation well pumping volumes and a 3-month irrigation period indicate water-level declines that range from 5.3 to 20 feet, 2.8 to 12 feet and 1.7 to 6.9 feet at distances of about 0.5, 1.5 and 3 miles from irrigation wells, respectively. Residential wells that are equipped with shallow jet pumps and that are within 0.5 miles of irrigation wells would likely experience reduced yield or loss of yield during peak periods of irrigation. The actual 1 extent that irrigation pumping cause reduced function of residential wells, however, cannot be fully predicted on the basis of the data analyzed because many _other factors may be adversely affecting the yield of residential wells.

Electrochemical oxygen pumps. Final CRADA report.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carter, J. D.

2009-10-01

All tasks of the Work Plan of ISTC Project 2277p have been completed, thus: (1) techniques of chemical synthesis were developed for more than ten recipes of electrolyte based on cerium oxide doped with 20 mole% of gadolinium (CeGd)O{sub 2}, doped by more than 10 oxide systems including 6 recipes in addition to the Work Plan; (2) electric conductivity and mechanical strength of CeGd specimens with additions of oxide systems were performed, two candidate materials for the electrolyte of electrochemical oxygen pump (pure CeGd and CeGd doped by 0.2 wt% of a transition metal) were chosen; (3) extended studies ofmore » mechanical strength of candidate material specimens were performed at room temperature and at 400, 600, 800 C; (4) fixtures for determination of mechanical strength of tubes by external pressure above 40 atmospheres at temperature up to 700 C were developed and fabricated; and (5) technology of slip casting of tubes from pure (Ce,Gd)O{sub 2} and of (Ce,Gd)O{sub 2} doped by 0.2 wt% of a transition metal, withstanding external pressure of minimum 40 atmospheres at temperature up to 700 C was developed, a batch of tubes was sent for testing to Argonne National Laboratory; (6) technology of making nanopowder from pure (Ce,Gd)O{sub 2} was developed based on chemical synthesis and laser ablation techniques, a batch of nanopowder with the weight 1 kg was sent for testing to Argonne National Laboratory; (7) a business plan for establishing a company for making powders of materials for electrochemical oxygen pump was developed; and (8) major results obtained within the Project were reported at international conferences and published in the Russian journal Electrochemistry. In accordance with the Work Plan a business trip of the following project participants was scheduled for April 22-29, 2006, to Tonawanda, NY, USA: Manager Victor Borisov; Leader of technology development Gennady Studenikin; Leader of business planning Elena Zadorozhnaya; Leader of production Vasily Lepalovsky; and Translator Vladimir Litvinov. During this trip project participants were to discuss with the project Technical Monitor J.D. Carter and representative of Praxair Inc. J. Chen the results of project activities (prospects of transition metal-doped material application in oxygen pumps), as well as the prospects of cooperation with Praxair at the meeting with the company management in the following fields: (1) Deposition of thin films of oxide materials of complex composition on support by magnetron and ion sputtering, research of coatings properties; (2) Development of block-type structure technology (made of porous and dense ceramics) for oxygen pump. The block-type structure is promising because when the size of electrolyte block is 2 x 2 inches and assembly height is 10 inches (5 blocks connected together) the area of active surface is ca. 290 square inches (in case of 8 slots), that roughly corresponds to one tube with diameter 1 inch and height 100 inches. So performance of the system made of such blocks may be by a factor of two or three higher than that of tube-based system. However one month before the visit, J. Chen notified us of internal changes at Praxair and the cancellation of the visit to Tonawanda, NY. During consultations with the project Technical Monitor J.D. Carter and Senior Project Manager A. Taylor a decision was made to extend the project term by 2 quarters to prepare proposals for follow-on activities during this extension (development of block-type structures made of dense and porous oxide ceramics for electrochemical oxygen pumps) using the funds that were not used for the trip to the US.« less

CRADA Final Report: Weld Predictor App

DOE Office of Scientific and Technical Information (OSTI.GOV)

Billings, Jay Jay

Welding is an important manufacturing process used in a broad range of industries and market sectors, including automotive, aerospace, heavy manufacturing, medical, and defense. During welded fabrication, high localized heat input and subsequent rapid cooling result in the creation of residual stresses and distortion. These residual stresses can significantly affect the fatigue resistance, cracking behavior, and load-carrying capacity of welded structures during service. Further, additional fitting and tacking time is often required to fit distorted subassemblies together, resulting in non-value added cost. Using trial-and-error methods to determine which welding parameters, welding sequences, and fixture designs will most effectively reduce distortionmore » is a time-consuming and expensive process. For complex structures with many welds, this approach can take several months. For this reason, efficient and accurate methods of mitigating distortion are in-demand across all industries where welding is used. Analytical and computational methods and commercial software tools have been developed to predict welding-induced residual stresses and distortion. Welding process parameters, fixtures, and tooling can be optimized to reduce the HAZ softening and minimize weld residual stress and distortion, improving performance and reducing design, fabrication and testing costs. However, weld modeling technology tools are currently accessible only to engineers and designers with a background in finite element analysis (FEA) who work with large manufacturers, research institutes, and universities with access to high-performance computing (HPC) resources. Small and medium enterprises (SMEs) in the US do not typically have the human and computational resources needed to adopt and utilize weld modeling technology. To allow an engineer with no background in FEA and SMEs to gain access to this important design tool, EWI and the Ohio Supercomputer Center (OSC) developed the online weld application software tool “WeldPredictor” ( https://eweldpredictor.ewi.org ). About 1400 users have tested this application. This project marked the beginning of development on the next version of WeldPredictor that addresses many outstanding features of the original, including 3D models, allow more material hardening laws, model material phase transformation, and uses open source finite element solvers to quickly solve problems (as opposed to expensive commercial tools).« less

TORO II simulations of induction heating in ferromagnetic materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adkins, D.R.; Gartling, D.K.; Kelley, J.B.

TORO II is a finite element computer program that is used in the simulation of electric and magnetic fields. This code, which was developed at Sandia National Laboratories, has been coupled with a finite element thermal code, COYOTE II, to predict temperature profiles in inductively heated parts. The development of an effective technique to account for the nonlinear behavior of the magnetic permeability in ferromagnetic parts is one of the more difficult aspects of solving induction heating problems. In the TORO II code, nonlinear, spatially varying magnetic permeability is approximated by an effective permeability on an element-by-element basis that effectivelymore » provides the same energy deposition that is produced when the true permeability is used. This approximation has been found to give an accurate estimate of the volumetric heating distribution in the part, and predicted temperature distributions have been experimentally verified using a medium carbon steel and a 10kW industrial induction heating unit. Work on the model was funded through a Cooperative Research and Development Agreement (CRADA) between the Department of Energy and General Motors` Delphi Saginaw Steering Systems.« less

Hydrogeologic framework of Pennsylvanian and Late Mississippian rocks in the central lower peninsula of Michigan

USGS Publications Warehouse

Westjohn, David B.; Weaver, Thomas L.

1996-01-01

Late Mississippian and Pennsylvanian sedimentary rocks form part of a regional system of aquifers and confining units in the central Lower Peninsula of Michigan. The upper part of the Pennsylvanian rock sequence constitutes the Saginaw aquifer, which consists primarily of sandstone. This sandstone aquifer overlies the Saginaw confining unit, which consists primarily of shale. The Saginaw confining unit separates the Saginaw aquifer from the Parma-Bayport aquifer, which consists primarily of permeable sandstones and carbonates; these permeable units are interpreted to be hydraulically connected and stratigraphically continuous at the scale of the regional aquifer system. The Saginaw aquifer ranges in thickness from 100 to 370 feet along a 30- to 45-milewide south-trending corridor through the approximate center of the aquifer system. The Saginaw aquifer typically contains freshwater along this corridor of thick sandstone. Most municipalities that use water from the Saginaw aquifer are located along this corridor. On either side of this corridor, the Saginaw aquifer generally is less than 100-feet thick, and typically contains saline water. Altitude of the surface of the Saginaw aquifer ranges from 800 to 900 feet in the northern part of the aquifer system, and from 500 to 600 feet in the southern part. Altitude of the top of the Saginaw aquifer is lower in the western and eastern parts of the aquifer system (typically 400 to 500 feet). The Saginaw confining unit is thickest in the northwestern part of the aquifer system (100 to 240 feet thick); however, thickness decreases to 50 feet in the southeast. Thickness of the Parma-Bayport aquifer generally ranges from 100 to 150 feet. The surface configuration of this aquifer is similar in shape to the Saginaw aquifer; altitudes are highest in the southern and northern parts of the aquifer system (900 and 500 feet, respectively). Lowest altitude (approximately -100 feet) of the Parma-Bayport aquifer is in the east

Comparison of the uptake of dioxin-like compounds by caged channel catfish and semipermeable membrane devices in the Saginaw River, Michigan

USGS Publications Warehouse

Gale, Robert W.; Huckins, James N.; Petty, Jimmie D.; Peterman, Paul H.; Williams, Lisa L.; Morse, Douglas; Schwartz, Ted R.; Tillitt, Donald E.

1996-01-01

Elevated concentrations of planar, halogenated hydrocarbons have been linked to reproductive problems in a variety of fish-eating birds and mammals in the Great Lakes and in particular Saginaw Bay. Currently, there are no accurate procedures to assess bioavailability of these contaminants. Polychlorinated dibenzo-p-dioxins and dibenzofurans and mono- and non-ortho-chloro-substituted biphenyls in water at the femtogram to picogram per liter range were passively concentrated in semipermeable membrane devices (SPMDs), and these data were compared to the bioconcentration in co-exposed (caged) channel catfish. Sediment-derived water concentration estimates, calculated from a steady-state partitioning model, did not correlate well to those derived from either fish or SPMDs. The use of SPMDs demonstrated the utility of in-situ passive sampling over inference of water concentrations from accumulation in biota or partitioning with sediment. Residues ac cumulated by SPMDs have been shown to be proportional to analyte water concentration, whereas this does not appear to be the case for fish tissues. The greater amounts of 3,3‘,4,4‘-tetrachlorobiphenyl and 2,3,7,8-tetrachlorodibenzofuran accumulated in SPMDs than in exposed channel catfish indicated those non-passive aspects of bioconcentration in organisms, such as biotransformation and elimination, introduced 50−500% error in the assumed degree of exposure.

Radiation Hardened Telerobotic Dismantling System Development Final Report CRADA No. TC-1340-96

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, C.; Lightman, A.

This project was a collaborative effort between the University of California, LLNL and RedZone Robotics, Inc. for the development of radiation-hardened telerobotic dismantling systems for use in applications such as nuclear facility remediation, nuclear accident response, and Chemobyltype remediation. The project supported the design, development, fabrication and testing of a Ukrainian robotic systems. The project was completed on time and within budget. All deliverables were completed. The final project deliverables were consistent with the plans developed in the original project with the exception that the fabricated systems remained in Ukraine.

University of Washington/ Northwest National Marine Renewable Energy Center Tidal Current Technology Test Protocol, Instrumentation, Design Code, and Oceanographic Modeling Collaboration: Cooperative Research and Development Final Report, CRADA Number CRD-11-452

DOE Office of Scientific and Technical Information (OSTI.GOV)

Driscoll, Frederick R.

The University of Washington (UW) - Northwest National Marine Renewable Energy Center (UW-NNMREC) and the National Renewable Energy Laboratory (NREL) will collaborate to advance research and development (R&D) of Marine Hydrokinetic (MHK) renewable energy technology, specifically renewable energy captured from ocean tidal currents. UW-NNMREC is endeavoring to establish infrastructure, capabilities and tools to support in-water testing of marine energy technology. NREL is leveraging its experience and capabilities in field testing of wind systems to develop protocols and instrumentation to advance field testing of MHK systems. Under this work, UW-NNMREC and NREL will work together to develop a common instrumentation systemmore » and testing methodologies, standards and protocols. UW-NNMREC is also establishing simulation capabilities for MHK turbine and turbine arrays. NREL has extensive experience in wind turbine array modeling and is developing several computer based numerical simulation capabilities for MHK systems. Under this CRADA, UW-NNMREC and NREL will work together to augment single device and array modeling codes. As part of this effort UW NNMREC will also work with NREL to run simulations on NREL's high performance computer system.« less

Sex difference in polybrominated diphenyl ether concentrations of walleyes

USGS Publications Warehouse

Madenjian, Charles P.; Trombka, Autumn W.; Rediske, Richard R.; Jude, David J.; O'Keefe, James P.

2012-01-01

Polybrominated diphenyl ether (PBDE) concentrations were determined for mature male and mature female walleyes (Sander vitreus) sampled from the Saginaw Bay population during 2007. PBDE concentrations in prey fish caught in the Saginaw River, the primary tributary to Saginaw Bay, and in Saginaw Bay during 2005 and 2007 also were determined. Mature male and mature female walleyes averaged 70.3 ng/g and 24.8 ng/g, respectively, in ΣPBDE, which was equal to the sum of concentrations of six PBDE congeners (BDE-28, BDE-47, BDE-99, BDE-100, BDE-153, and BDE-154). This sex difference was likely due to males spending more time in the Saginaw River system than females. Prey fish captured in the Saginaw River were roughly ten times higher in ΣPBDE than those caught in Saginaw Bay. BDE-47 was the predominant congener in both walleyes and prey fish, and this congener contributed about 50%, on average, to ΣPBDE. Congener profiles differed significantly between the two sexes of walleyes. In contrast, congener profiles of the prey fish did not differ significantly between the river-caught fish and the bay-caught fish. One plausible explanation for these congener profile results was that net trophic transfer efficiencies of PBDEs to walleyes from their prey were similar for all congeners except BDE-28, and that diet composition differed between the two sexes of walleyes.

Final Report of a CRADA Between Pacific Northwest National Laboratory and Cummins, Incorporated (CRADA No.PNNL/283): “Enhanced High and Low Temperature Performance of NO x Reduction Catalyst Materials”

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gao, Feng; Szanyi, Janos; Wang, Yilin

eliminate emissions at these quite low exhaust temperatures. This project has two clear focuses: (1) development of potassium-based high-temperature NSR materials, and studying their key causes of deactivation and methods of regeneration. By comparing results obtained on ‘Simple Model’ Pt-K/Al 2O 3 with ‘Enhanced Model’ Pt-K/ MgAlO x and Pt-K/TiO 2 materials, we have developed an understanding of the role of various additives on the deactivation and regeneration processes. Studies have also been performed on the real commercial samples being used in a Dodge Ram truck with a Cummins diesel emission control system. However, the results about these ‘commercial samples’ will not be covered in this report. Following a brief description of our experimental approach, we will present a few highlights from some of the work performed in this CRADA with more details about these results provided in publications/reports/presentations lists presented at the end of the report. (2) for the Cu and Fe/Chabazite SCR catalysts, since these are so newly developed and references from open literature and industry are nearly absent, our work started from zeolite synthesis and catalyst synthesis methodology development, before research on their low- and high-temperature performance, deactivation, regeneration, etc. was conducted. Again, most work reported here is based on our “model” catalysts synthesized in-house. Work done on the ‘commercial samples’ will not be covered in this report.« less

Cross-correlation map analyses show weather variation influences on mosquito abundance patterns in Saginaw County, Michigan, 1989-2005.

PubMed

Chuang, Ting-Wu; Ionides, Edward L; Knepper, Randall G; Stanuszek, William W; Walker, Edward D; Wilson, Mark L

2012-07-01

Weather is important determinant of mosquito abundance that, in turn, influences vectorborne disease dynamics. In temperate regions, transmission generally is seasonal as mosquito abundance and behavior varies with temperature, precipitation, and other meteorological factors. We investigated how such factors affected species-specific mosquito abundance patterns in Saginaw County, MI, during a 17-yr period. Systematic sampling was undertaken at 22 trapping sites from May to September, during 1989-2005, for 19,228 trap-nights and 300,770 mosquitoes in total. Aedes vexans (Meigen), Culex pipiens L. and Culex restuans Theobald, the most abundant species, were analyzed. Weather data included local daily maximum temperature, minimum temperature, total precipitation, and average relative humidity. In addition to standard statistical methods, cross-correlation mapping was used to evaluate temporal associations with various lag periods between weather variables and species-specific mosquito abundances. Overall, the average number of mosquitoes was 4.90 per trap-night for Ae. vexans, 2.12 for Cx. pipiens, and 1.23 for Cx. restuans. Statistical analysis of the considerable temporal variability in species-specific abundances indicated that precipitation and relative humidity 1 wk prior were significantly positively associated with Ae. vexans, whereas elevated maximum temperature had a negative effect during summer. Cx. pipiens abundance was positively influenced by the preceding minimum temperature in the early season but negatively associated with precipitation during summer and with maximum temperature in July and August. Cx. restuans showed the least weather association, with only relative humidity 2-24 d prior being linked positively during late spring-early summer. The recently developed analytical method applied in this study could enhance our understanding of the influences of weather variability on mosquito population dynamics.

Solutions for Digital Video Transmission Technology Final Report CRADA No. TC02068.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, A. T.; Rivers, W.

This Project aimed at development of software for seismic data processing based on the Geotool code developed by the American company Multimax., Inc. The Geotool code was written in early 90-es for the UNIX platform. Under Project# 2821, functions of the old Geotool code were transferred into a commercial version for the Microsoft XP and Vista platform with addition of new capabilities on visualization and data processing. The developed new version of the Geotool+ was implemented using the up-to-date tool Microsoft Visual Studio 2005 and uses capabilities of the .NET platform. C++ was selected as the main programming language formore » the Geotool+. The two-year Project was extended by six months and funding levels increased from 600,000 to $670,000. All tasks were successfully completed and all deliverables were met for the project even though both the industrial partner and LLNL principal investigator left the project before its final report.« less

Reconnaissance Study for the Western Lake Huron Basin, Watershed Study, Michigan, Section 905(b)

DTIC Science & Technology

2012-05-01

Isle, Alpena , Alcona, Iosco, Arenac, Bay, Tuscola, Huron, Sanilac, St. Clair, Midland, and Saginaw. With the exception of Midland and Saginaw Counties...Cheboygan, Presque Isle, Alpena , Alcona, Iosco, Arenac, Bay, Midland, Saginaw, Tuscola, Huron, Sanilac, and St. Clair. The study area includes the... Alpena Harbor. Alpena Harbor is at the mouth of the Thunder Bay River, which empties into Thunder Bay, Lake Huron. The harbor is 100 miles southeast of

CRADA Final Report for CRADA Number NFE-08-01671 Materials for Advanced Turbocharger Designs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maziasz, P. J.; Wilson, M.

2014-11-28

Results were obtained on residual stresses in the weld of the steel shaft to the Ni-based superalloy turbine wheel for turbochargers. Neutron diffraction studies at the HFIR Residual Stress Facility showed asymmetric tensile stresses after electron-beam welding of the wheel and shaft. A post-weld heat-treatment was found to relieve and reduce the residual stresses. Results were also obtained on cast CF8C-Plus steel as an upgrade alternative to cast irons (SiMo, Ni-resist) for higher temperature capability and performance for the turbocharger housing. CF8C-Plus steel has demonstrated creep-rupture resistance at 600-950oC, and is more creep-resistant than HK30Nb, but lacks oxidation-resistance at 800oCmore » and above in 10% water vapor. New modified CF8C-Plus Cu/W steels with Cr and Ni additions show better oxidation resistance at 800oC in 10% water vapor, and have capability to higher temperatures. For automotive gasoline engine turbocharger applications, higher temperatures are required, so at the end of this project, testing began at 1000oC and above.« less

Transactive Campus Energy Systems: Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Katipamula, Srinivas; Corbin, Charles D.; Haack, Jereme N.

Transactive energy refers to the combination of economic and control techniques to improve grid reliability and efficiency. The fundamental purpose of transactive energy management is to seamlessly coordinate the operation of large numbers of new intelligent assets—such as distributed solar, energy storage and responsive building loads—to provide the flexibility needed to operate the power grid reliably and at minimum cost, particularly one filled with intermittent renewable generation such as the Pacific Northwest. It addresses the key challenge of providing smooth, stable, and predictable “control” of these assets, despite the fact that most are neither owned nor directly controlled by themore » power grid. The Clean Energy and Transactive Campus (CETC) work described in this report was done as part of a Cooperative Research and Development Agreement (CRADA) between the U.S. Department of Energy’s Pacific Northwest National Laboratory (PNNL) and the Washington State Department of Commerce (Commerce) through the Clean Energy Fund (CEF). The project team consisted of PNNL, the University of Washington (UW) and Washington State University (WSU), to connect the PNNL, UW, and WSU campuses to form a multi-campus testbed for transaction-based energy management—transactive—solutions. Building on the foundational transactive system established by the Pacific Northwest Smart Grid Demonstration (PNWSGD), the purpose of the project was to construct the testbed as both a regional flexibility resource and as a platform for research and development (R&D) on buildings/grid integration and information-based energy efficiency. This report provides a summary of the various tasks performed under the CRADA.« less

Gender difference in walleye PCB concentrations persists following remedial dredging

USGS Publications Warehouse

Madenjian, Charles P.; Jude, David J.; Rediske, Richard R.; O'Keefe, James P.; Noguchi, George E.

2009-01-01

Eleven male walleyes (Sander vitreus) and 10 female walleyes from the Saginaw Bay (Lake Huron) population were caught during the spawning run at Dow Dam (Midland, Michigan) in the Tittabawassee River during April 1996, and individual whole-fish polychlorinated biphenyl (PCB) determinations were made. Total PCB concentrations averaged 7.95 and 3.17??mg/kg for males and females, respectively. As part of the Natural Resource Damage Assessment remediation process, contaminated sediments from the Saginaw River, the main tributary to Saginaw Bay, were removed during 2000 and 2001. Total PCB concentrations of 10 male and 10 female walleyes caught at Dow Dam during April 2007 averaged 1.58 and 0.55??mg/kg, respectively. Thus, dredging of the Saginaw River appeared to be effective in reducing PCB concentrations of Saginaw Bay adult walleyes, as both males and females decreased in PCB concentration by more than 80% between 1996 and 2007. However, the ratio of male PCB concentration to female PCB concentration did not decline between 1996 and 2007. This persistent gender difference in PCB concentrations was apparently due to a gender difference in habitat utilization coupled with a persistent spatial gradient in prey fish PCB concentrations from the Saginaw River to Lake Huron.

AN "ENVIRO-INFORMATIC" ASSESSMENT OF SAGINAW BAY (LAKE HURON, USA) PHYTOPLANKTON: DATA-DRIVEN CHARACTERIZATION AND MODELING OF MICROCYSTIS (CYANOPHYTA)(1).

PubMed

Millie, David F; Fahnenstiel, Gary L; Weckman, Gary R; Klarer, David M; Dyble, Julianne; Vanderploeg, Henry A; Fishman, Daniel B

2011-08-01

Phytoplankton and Microcystis aeruginosa (Kütz.) Kütz. biovolumes were characterized and modeled, respectively, with regard to hydrological and meteorological variables during zebra mussel invasion in Saginaw Bay (1990-1996). Total phytoplankton and Microcystis biomass within the inner bay were one and one-half and six times greater, respectively, than those of the outer bay. Following mussel invasion, mean total biomass in the inner bay decreased 84% but then returned to its approximate initial value. Microcystis was not present in the bay during 1990 and 1991 and thereafter occurred at/in 52% of sample sites/dates with the greatest biomass occurring in 1994-1996 and within months having water temperatures >19°C. With an overall relative biomass of 0.03 ± 0.01 (mean + SE), Microcystis had, at best, a marginal impact upon holistic compositional dynamics. Dynamics of the centric diatom Cyclotella ocellata Pant. and large pennate diatoms dominated compositional dissimilarities both inter- and intra-annually. The environmental variables that corresponded with phytoplankton distributions were similar for the inner and outer bays, and together identified physical forcing and biotic utilization of nutrients as determinants of system-level biomass patterns. Nonparametric models explained 70%-85% of the variability in Microcystis biovolumes and identified maximal biomass to occur at total phosphorus (TP) concentrations ranging from 40 to 45 μg · L(-1) . From isometric projections depicting modeled Microcystis/environmental interactions, a TP concentration of <30 μg · L(-1) was identified as a desirable contemporary "target" for management efforts to ameliorate bloom potentials throughout mussel-impacted bay waters. © 2011 Phycological Society of America.

CRADA Final Report, 2011S003, Faraday Technologies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Faraday Technologies

2012-12-12

This Phase I SBIR program addressed the need for an improved manufacturing process for electropolishing niobium RF superconducting cavities for the International Linear Collider (ILC). The ILC is a proposed particle accelerator that will be used to gain a deeper understanding of the forces of energy and matter by colliding beams of electrons and positrons at nearly the speed of light. The energy required for this to happen will be achieved through the use of advanced superconducting technology, specifically ~16,000 RF superconducting cavities operating at near absolute zero. The RF superconductor cavities will be fabricated from highly pure Nb, whichmore » has an extremely low surface resistance at 2 Kelvin when compared to other materials. To take full advantage of the superconducting properties of the Nb cavities, the inner surface must be a) polished to a microscale roughness < 0.1 µm with removal of at least 100 µm of material, and b) cleaned to be free of impurities that would degrade performance of the ILC. State-of-the-art polishing uses either chemical polishing or electropolishing, both of which require hydrofluoric acid to achieve breakdown of the strong passive film on the surface. In this Phase I program, Faraday worked with its collaborators at the Thomas Jefferson National Accelerator Facility (JLab) to demonstrate the feasibility of an electropolishing process for pure niobium, utilizing an environmentally benign alternative to chemical or electrochemical polishing electrolytes containing hydrofluoric acid. Faraday utilized a 31 wt% aqueous sulfuric acid solution (devoid of hydrofluoric acid) in conjunction with the FARADAYICSM Process, which uses pulse/pulse reverse fields for electropolishing, to demonstrate the ability to electropolish niobium to the desired surface finish. The anticipated benefits of the FARADAYICSM Electropolishing process will be a simpler, safer, and less expensive method capable of surface finishing high purity niobium cavities. Another potential benefit would be for the medical industry that uses hydrofluoric acid to electropolish niobium-alloy materials. The FARADAYICSM Electropolishing process will eliminate the environmental hazards posed by the use of hydrofluoric acid employed by chemical polishing and conventional electropolishing. Further, improved performance benefits may be possible. The overall objective of the Phase I program was to demonstrate that FARADAYIC Electropolishing of niobium cavities in electrolytes free of hydrofluoric acid can meet the RF superconducting performance criteria of those cavities. The FARADAYIC Electropolishing Process developed in the Phase I program was used to polish 50 mm Nb disks to a surface roughness (RA) of < 1 nm over a small area through process and post-processing optimization. An excellent level of surface cleanliness was achieved. While the desired 2K RF performance has not yet been achieved, Faraday believes that surface oxide state can be controlled through manipulation of the process parameters, to meet the 2K RF standard. Faraday is establishing apparatus and facilities infrastructure for single-cell SRF cavity electropolishing, through a synergistic effort with the Fermi National Accelerator Facility (Fermilab) to scale-up electropolishing of superconducting RF cavities. Faraday proposes to commercialize the subject technology via an IP based strategic relationship with a partner with established market channels within two primary commercialization avenues: 1) the superconducting particle accelerator community, 2) the medical device and implant market. Faraday will initially maintain Low Rate Initial Production capabilities for an application, but latterly seek a strategic partner who is solely dedicated to high rate production.« less

CRADA No. BNL-C-97-10 between BNL and Cotton, Inc. Final abstract and final report [Final Report of Research carried out under DOE CRADA No. BNL-C-97-10 - "Prediction of Yield in Cotton"

DOE Office of Scientific and Technical Information (OSTI.GOV)

None, None

The objectives of this work were to determine if the numbér of fiber cell initials varied genetically and to compare the number of initials with that of mature fibers obtained at harvest time. The method used to count the number of fiber cell initials is direct, simple, quick and done while the plant is growing. In contrast, the currently used commercial process is indirect and needs large amount mature fibers gathered at harvest time. However, all current work on cotton yield is based on fiber numbers obtained by the indirect commercial process. Consequently, it was necessary to compare results obtainedmore » from the two methods using the same plants as the source of material. The results show that the number of fiber initials per ovule differed significantly (P>0.05) for seven cultivars in 1995 and 1996. AIso, a 1997 study shows the number of fiber initials varied by 15% over boll positions and environments, with rankings among cultivars generally consistent across boll positions and sampling times. Finally, although there were differences among cultivars for initial fiber cell number, all cultivars had nearly the same number of mature lint fibers per seed. This last finding is significant. It indicates that the rate of fiber cell initiation varies among cultivars; the lower the rate, the greater the difference between the number of initials and the number of mature fiber cells. If the rate of fiber initiation is relatively high, the number of initials and mature fibers differs by about 11%; if it is low, the difference is as high as 31%. Cotton breeders may be able to use genetic differences for the number of fiber initials and/or the rate of fiber cell initiation in crop improvement programs.« less

Acoustic telemetry reveals large-scale migration patterns of walleye in Lake Huron

USGS Publications Warehouse

Hayden, Todd A.; Holbrook, Christopher; Fielder, David G.; Vandergoot, Christopher S.; Bergstedt, Roger A.; Dettmers, John M.; Krueger, Charles C.; Cooke, Steven J.

2014-01-01

Fish migration in large freshwater lacustrine systems such as the Laurentian Great Lakes is not well understood. The walleye (Sander vitreus) is an economically and ecologically important native fish species throughout the Great Lakes. In Lake Huron walleye has recently undergone a population expansion as a result of recovery of the primary stock, stemming from changing food web dynamics. During 2011 and 2012, we used acoustic telemetry to document the timing and spatial scale of walleye migration in Lake Huron and Saginaw Bay. Spawning walleye (n = 199) collected from a tributary of Saginaw Bay were implanted with acoustic tags and their migrations were documented using acoustic receivers (n = 140) deployed throughout U.S. nearshore waters of Lake Huron. Three migration pathways were described using multistate mark-recapture models. Models were evaluated using the Akaike Information Criterion. Fish sex did not influence migratory behavior but did affect migration rate and walleye were detected on all acoustic receiver lines. Most (95%) tagged fish migrated downstream from the riverine tagging and release location to Saginaw Bay, and 37% of these fish emigrated from Saginaw Bay into Lake Huron. Remarkably, 8% of walleye that emigrated from Saginaw Bay were detected at the acoustic receiver line located farthest from the release location more than 350 km away. Most (64%) walleye returned to the Saginaw River in 2012, presumably for spawning. Our findings reveal that fish from this stock use virtually the entirety of U.S. nearshore waters of Lake Huron.

Acoustic telemetry reveals large-scale migration patterns of walleye in Lake Huron.

PubMed

Hayden, Todd A; Holbrook, Christopher M; Fielder, David G; Vandergoot, Christopher S; Bergstedt, Roger A; Dettmers, John M; Krueger, Charles C; Cooke, Steven J

2014-01-01

Fish migration in large freshwater lacustrine systems such as the Laurentian Great Lakes is not well understood. The walleye (Sander vitreus) is an economically and ecologically important native fish species throughout the Great Lakes. In Lake Huron walleye has recently undergone a population expansion as a result of recovery of the primary stock, stemming from changing food web dynamics. During 2011 and 2012, we used acoustic telemetry to document the timing and spatial scale of walleye migration in Lake Huron and Saginaw Bay. Spawning walleye (n = 199) collected from a tributary of Saginaw Bay were implanted with acoustic tags and their migrations were documented using acoustic receivers (n = 140) deployed throughout U.S. nearshore waters of Lake Huron. Three migration pathways were described using multistate mark-recapture models. Models were evaluated using the Akaike Information Criterion. Fish sex did not influence migratory behavior but did affect migration rate and walleye were detected on all acoustic receiver lines. Most (95%) tagged fish migrated downstream from the riverine tagging and release location to Saginaw Bay, and 37% of these fish emigrated from Saginaw Bay into Lake Huron. Remarkably, 8% of walleye that emigrated from Saginaw Bay were detected at the acoustic receiver line located farthest from the release location more than 350 km away. Most (64%) walleye returned to the Saginaw River in 2012, presumably for spawning. Our findings reveal that fish from this stock use virtually the entirety of U.S. nearshore waters of Lake Huron.

Sexual difference in polychlorinated biphenyl accumulation rates of walleye (Stizostedion vitreum)

USGS Publications Warehouse

Madenjian, Charles P.; Noguchi, George E.; Haas, Robert C.; Schrouder, Kathrin S.

1998-01-01

Adult male walleye (Stizostedion vitreum) exhibited significantly higher polychlorinated biphenyl (PCB) concentrations than similarly aged female walleye from Saginaw Bay (Lake Huron). To explain this difference, we tested the following three hypotheses: (i) females showed a considerably greater reduction in PCB concentration immediately following spawning than males, (ii) females grew at a faster rate and therefore exhibited lower PCB concentrations than males, and (iii) males spent more time in the Saginaw River system than females, and therefore received a greater exposure to PCBs. The first hypothesis was tested by comparing PCB concentration in gonadal tissue with whole-body concentration, the second hypothesis was tested via bioenergetics modeling, and we used mark-recapture data from the Saginaw Bay walleye fishery to address the third hypothesis. The only plausible explanation for the observed difference in PCB accumulation rate was that males spent substantially more time in the highly contaminated Saginaw River system than females, and therefore were exposed to greater environmental concentrations of PCBs. Based on the results of our study, we strongly recommend a stratified random sampling design for monitoring PCB concentration in Saginaw Bay walleye, with fixed numbers of females and males sampled each year.

76 FR 14691 - Delphi Steering, Including On-Site Leased Workers From Acro Service Corporation, Aerotek, Inc...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-17

... Health Care and Advantage Technical Resourcing, Saginaw, MI; Amended Certification Regarding Eligibility... on-site leased workers from Advantage Technical Resourcing were employed on-site at the Saginaw... Department is amending this certification to include workers leased from Advantage Technical Resourcing...

Acoustic Telemetry Reveals Large-Scale Migration Patterns of Walleye in Lake Huron

PubMed Central

Hayden, Todd A.; Holbrook, Christopher M.; Fielder, David G.; Vandergoot, Christopher S.; Bergstedt, Roger A.; Dettmers, John M.; Krueger, Charles C.; Cooke, Steven J.

2014-01-01

Fish migration in large freshwater lacustrine systems such as the Laurentian Great Lakes is not well understood. The walleye (Sander vitreus) is an economically and ecologically important native fish species throughout the Great Lakes. In Lake Huron walleye has recently undergone a population expansion as a result of recovery of the primary stock, stemming from changing food web dynamics. During 2011 and 2012, we used acoustic telemetry to document the timing and spatial scale of walleye migration in Lake Huron and Saginaw Bay. Spawning walleye (n = 199) collected from a tributary of Saginaw Bay were implanted with acoustic tags and their migrations were documented using acoustic receivers (n = 140) deployed throughout U.S. nearshore waters of Lake Huron. Three migration pathways were described using multistate mark-recapture models. Models were evaluated using the Akaike Information Criterion. Fish sex did not influence migratory behavior but did affect migration rate and walleye were detected on all acoustic receiver lines. Most (95%) tagged fish migrated downstream from the riverine tagging and release location to Saginaw Bay, and 37% of these fish emigrated from Saginaw Bay into Lake Huron. Remarkably, 8% of walleye that emigrated from Saginaw Bay were detected at the acoustic receiver line located farthest from the release location more than 350 km away. Most (64%) walleye returned to the Saginaw River in 2012, presumably for spawning. Our findings reveal that fish from this stock use virtually the entirety of U.S. nearshore waters of Lake Huron. PMID:25506913

Polychlorinated dibenzo-p-dioxins, dibenzofurans, biphenyls and 2,3,7,8-tetrachlorodibenzo-p-dioxin equivalents in fishes from Saginaw Bay, Michigan

USGS Publications Warehouse

Giesy, John P.; Jude, David J.; Tillitt, Donald E.; Gale, Robert W.; Meadows, John C.; Zajieck, James L.; Peterman, Paul H.; Verbrugge, David A.; Sanderson, J. Thomas; Schwartz, Ted R.; Tuchman, Marc L.

1997-01-01

Concentrations of polychlorinated biphenyls (PCBs), polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs), polychlorinated naphthalenes (PCNs), polychlorinated dibenzothiophenes (PCDTs), and 2,3,7,8-tetrachlo-rodibenzo-p-dioxin (2,3,7,8-TCDD) equivalents were measured in composite samples of forage fishes and several sizes of walleyes (Stizostedion vitreum) and common carp (Cyprinus carpio) collected from Saginaw Bay, Michigan, USA. The concentrations of 2,3,7,8-TCDD equivalents determined from the use of TCDD equivalency factors (TEFs) and instrumentally determined concentrations of individual congeners were designated TEq. The 2,3,7,8-TCDD equivalents determined on the same extracts with the H4IIE bioassay were defined as TCDD-EQ. Concentrations of TCDD-EQ and TEq were significantly, but poorly correlated (R2 = 0.44). Concentrations of TCDD-EQ and TEq ranged from 10.6 to 348 and 13.5 to 69.5 ng/kg, wet weight, respectively. The ratio of TCDD-EQ to TEq ranged from 0.5 to 5.0, with the greatest ratio observed in common carp but the average ratio between TEq and TCDD-EQ was approximately 1.0. In common carp, larger walleye, and medium-sized alewife (Alosa pseudoharengus) there were significant concentrations of TCDD-EQ that could not be accounted for by TEq calculated from an additive model of PCBs, PCDDs, or PCDFs. As much as 75% of the TCDD-EQ in some samples could not be accounted for by TEqs. It is unlikely that PCNs, PCDTs, or polychlorinated diphenyl ethers (PCDEs) occurred at concentrations that were, based on their relative potencies, great enough to contribute significant quantities of TCDD-EQ. The discrepency between TCDD-EQs and TEqs was not due to antagonisms among congeners or extraction efficiencies.

Inverter Load Rejection Over-Voltage Testing: SolarCity CRADA Task 1a Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nelson, A.; Hoke, A.; Chakraborty, S.

Various interconnection challenges exist when connecting distributed PV into the electrical distribution grid in terms of safety, reliability, and stability of electric power systems. One of the urgent areas for additional research - as identified by inverter manufacturers, installers, and utilities - is the potential for transient over-voltage from PV inverters. In one stage of a cooperative tests were repeated a total of seven times. The maximum over-voltage measured in any test did not exceed 200% of nominal, and typical over-voltage levels were significantly lower. The total voltage duration and the maximum continuous time above each threshold are presented here,more » as well as the time to disconnect for each test. Finally, we present a brief investigation into the effect of DC input voltage as well as a series of no-load tests. This report describes testing conducted at NREL to determine the duration and magnitude of transient over-voltages created by several commercial PV inverters during load-rejection conditions. For this work, a test plan that is currently under development by the Forum on Inverter Grid Integration Issues (FIGII) has been implemented in a custom test setup at NREL. Through a cooperative research and development agreement, NREL is working with SolarCity to address two specific types of transient overvoltage: load rejection overvoltage (LRO) and ground fault overvoltage (GFO). Additional partners in this effort include the Hawaiian Electric Companies, Northern Plains Power Technologies, and the Electric Power Research Institute.« less

19 CFR 24.24 - Harbor maintenance fee.

Code of Federal Regulations, 2010 CFR

2010-04-01

... are intraport. 0404—Gloucester 0407—Fall River Michigan 3843—Alpena Fee does not apply to Stoneport... intraport. Upper Lake Huron Ports3803—Sault Ste. Marie 3804—Saginaw-Flint-Bay City 3843—Alpena Includes all points on the St. Mary's River, the ports of Cheyboygan, Alpena, Bay City, and Saginaw River. Does not...

Energy Systems Integration News | Energy Systems Integration Facility |

Science.gov Websites

Aids Solar Power in Hawaii Inverter load rejection overvoltage tests completed by NREL with partner the report, Inverter Load Rejection Over-Voltage Testing: SolarCity CRADA Task 1a Final Report. Based % of minimum daytime load (MDL) to 250% of MDL. If those increases are implemented, they will represent

Value Proposition of Department of Defense Domestic Technology Transfer

DTIC Science & Technology

2010-01-15

Directorate NASA Langley Research Center and Boundary Layer Research, Inc., Everett, WA CRADA/PLA Complete Trivalent Chromium Pretreatment Naval Air...Dynamics Directorate NASA Langley Research Center and Boundary Layer Research, Inc., Everett, WA CRADA/PLA Trivalent Chromium Processes Naval Air...Warfare Systems Center, Pacific Various CRADA On-Hold Safety Welding Cart Air Force Training Device Design and Engineering Center Spika Welding

Information Summary, Area of Concern: Saginaw River and Saginaw Bay.

DTIC Science & Technology

1991-03-01

useful in predicting loadings in areas where no data currently exist. S~ ills MDNR maintains a Pollution Emergency Alerting System ( PEAS ) to receive...reports of accidental discharges and related problems. PEAS records from January 1984 to October 1986 show that 101 discharge incidents occurred in the...341 1.00 144.2 65.9 20.1 241.1 277.9 Kawkawlin River 234 0.73 105.5 46.0 11.3 170.5 201.7 Sebewaing River 325 0.96 138.6 62.6 18.7 230.7 266.7 Pigeon

Improved Fiber Optics Final Report CRADA No. TSB-957-94

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fox, Glenn; Wilford, Sandy

The existing chemistry of Lumenyte® (an illumination fiber optic developed by LIC) was such that the component monomers inherently polymerized to a very hard mass if exposed to environmental IR, UV, or a combination of these frequencies. Lumenyte optic also would cure to a hard mass by exposure to the UV & IR generated by the illuminating lamps-although this could occur at a much slower rate, and the hardening could occur even when the adverse frequencies were filtered. The resultant product did not have the flexibility for the required applications. LIC's objective was to include other monomeric components in themore » formulation to impart permanent flexibility. LIC sought the expertise and the use of the facilities in the Polymeric Materials Section at LLNL to achieve this objective.« less

HCCI Combustion Engines Final Report CRADA No. TC02032.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aceves, S.; Lyford-Pike, E.

This was a collaborative effort between Lawrence Livermore National Security, LLC (formerly The Regents of the University of California)/Lawrence Livermore National Laboratory (LLNL) and Cummins Engine Company (Cwnmins), to advance the state of the art on HomogeneousCharge Compression-Ignition (HCCI) engines, resulting in a clean, high-efficiency alternative to diesel engines.

Artificial Retina Project: Final Report for CRADA ORNL 01-0625

DOE Office of Scientific and Technical Information (OSTI.GOV)

Greenbaum, E; Little, J

The U.S. Department of Energy’s Artificial Retina Project is a collaborative, multi-institutional effort to develop an implantable microelectronic retinal prosthesis that restores useful vision to people blinded by retinal diseases. The ultimate goal of the project is to restore reading ability, facial recognition, and unaided mobility in people with retinitis pigmentosa and age-related macular degeneration. The project taps into the unique research technologies and resources developed at DOE national laboratories to surmount the many technical challenges involved with developing a safe, effective, and durable product. The research team includes six DOE national laboratories, four universities, and private industry.

Laser Shot Peening Final Report CRADA No. TC-02059-03

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stuart, B. C.; Hackel, L.

This was a collaborative effort between The Regents of the University of California, Lawrence Livermore National Laboratory (LLNL) and Metal Improvement Company, Inc. (MIC), to further develop the laser shot peening technology. This project had an emphasis on laser development and government and military applications including DOE’s natural gas and oil technology program (NGOTP), Yucca Mountain Project (YMP), F-22 Fighter, etc.

Infrared Imaging Camera Final Report CRADA No. TC02061.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roos, E. V.; Nebeker, S.

This was a collaborative effort between the University of California, Lawrence Livermore National Laboratory (LLNL) and Cordin Company (Cordin) to enhance the U.S. ability to develop a commercial infrared camera capable of capturing high-resolution images in a l 00 nanoseconds (ns) time frame. The Department of Energy (DOE), under an Initiative for Proliferation Prevention (IPP) project, funded the Russian Federation Nuclear Center All-Russian Scientific Institute of Experimental Physics (RFNC-VNIIEF) in Sarov. VNIIEF was funded to develop a prototype commercial infrared (IR) framing camera and to deliver a prototype IR camera to LLNL. LLNL and Cordin were partners with VNIIEF onmore » this project. A prototype IR camera was delivered by VNIIEF to LLNL in December 2006. In June of 2007, LLNL and Cordin evaluated the camera and the test results revealed that the camera exceeded presently available commercial IR cameras. Cordin believes that the camera can be sold on the international market. The camera is currently being used as a scientific tool within Russian nuclear centers. This project was originally designated as a two year project. The project was not started on time due to changes in the IPP project funding conditions; the project funding was re-directed through the International Science and Technology Center (ISTC), which delayed the project start by over one year. The project was not completed on schedule due to changes within the Russian government export regulations. These changes were directed by Export Control regulations on the export of high technology items that can be used to develop military weapons. The IR camera was on the list that export controls required. The ISTC and Russian government, after negotiations, allowed the delivery of the camera to LLNL. There were no significant technical or business changes to the original project.« less

Information integrity and privacy for computerized medical patient records

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gallegos, J.; Hamilton, V.; Gaylor, T.

Sandia National Laboratories and Oceania, Inc. entered into a Cooperative Research and Development Agreement (CRADA) in November 1993 to provide ``Information Integrity and Privacy for Computerized Medical Patient Records`` (CRADA No. SC93/01183). The main objective of the project was to develop information protection methods that are appropriate for databases of patient records in health information systems. This document describes the findings and alternative solutions that resulted from this CRADA.

CRADA with Beckman Instruments and Pacific Northwest National Laboratory (PNL-013): Development and commercialization of the Unsaturated Flow Apparatus (UFA) using characterization of aridisols

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wright, J.; Conca, J.

1996-10-01

The objective of this Cooperative Research and Development Agreement (CRADA) was to develop and commercialize a technology conceived by scientists at Pacific Northwest National Laboratory (PNNL) and manufactured by Beckman Instruments, Inc. (Beckman), and to apply this technology to the characterization of and soils. The technology is the Unsaturated Flow Apparatus (UFA). The UFA provides a highly efficient method of direct, rapid measurement of hydraulic conductivity and other flow properties according to Darcy-Buckingham principles because the operator controls both the fluid driving force, using an ultracentrifuge, and the flow into the sample while it is spinning, with a rotating sealmore » assembly. The concept of using centrifugation to significantly decrease the time needed, from years or months to days, for study of subsurface transport, particularly under unsaturated conditions, was conceived by James Conca, Ph.D., and Judith Wright, Ph.D., in 1986. The prototype UFA was developed in 1988 because there was a need to rapidly and accurately determine transport parameters in soils, sediments, and rocks for the Grout Waste Disposal Program. Transport parameters are critical to modeling outcomes for site-specific solutions to environmental remediation and waste disposal problems.« less

Oak Ridge National Laboratory Wireless Charging of Electric Vehicles - CRADA Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Onar, Omer C.; Campbell, Steven L.; Seiber, Larry Eugene

Wireless power transfer (WPT) is a paradigm shift in electric-vehicle (EV) charging that offers the consumer an autonomous, safe, and convenient option to conductive charging and its attendant need for cables. With WPT, charging process can be fully automated due to the vehicle and grid side radio communication systems, and is non-contacting; therefore issues with leakage currents, ground faults, and touch potentials do not exist. It also eliminates the need for touching the heavy, bulky, dirty cables and plugs. It eliminates the fear of forgetting to plug-in and running out of charge the following day and eliminates the tripping hazardsmore » in public parking lots and in highly populated areas such as shopping malls, recreational areas, parking buildings, etc. Furthermore, the high-frequency magnetic fields employed in power transfer across a large air gap are focused and shielded, so that fringe fields (i.e., magnetic leakage/stray fields) attenuate rapidly over a transition region to levels well below limits set by international standards for the public zone (which starts at the perimeter of the vehicle and includes the passenger cabin). Oak Ridge National Laboratory s approach to WPT charging places strong emphasis on radio communications in the power regulation feedback channel augmented with software control algorithms. The over-arching goal for WPT is minimization of vehicle on-board complexity by keeping the secondary side content confined to coil tuning, rectification, filtering, and interfacing to the regenerative energy-storage system (RESS). This report summarizes the CRADA work between the Oak Ridge National Laboratory and the Toyota Research Institute of North America, Toyota Motor Engineering and Manufacturing North America (TEMA) on the wireless charging of electric vehicles which was funded by Department of Energy under DE-FOA-000667. In this project, ORNL is the lead agency and Toyota TEMA is one of the major partners. Over the course of the

How You Can Partner with NIH | NCI Technology Transfer Center | TTC

Cancer.gov

NCI Technology Transfer Center (TTC) provides an array of agreements to support the National Cancer Institute's partnering. Deciding which type of agreement to use can be a challenge: CRADA, MTA, collaboration, agreement, CTA, Materials-CRADA

Airbags to Martian Landers: Analyses at Sandia National Laboratories

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gwinn, K.W.

1994-03-01

A new direction for the national laboratories is to assist US business with research and development, primarily through cooperative research and development agreements (CRADAs). Technology transfer to the private sector has been very successful as over 200 CRADAs are in place at Sandia. Because of these cooperative efforts, technology has evolved into some new areas not commonly associated with the former mission of the national laboratories. An example of this is the analysis of fabric structures. Explicit analyses and expertise in constructing parachutes led to the development of a next generation automobile airbag; which led to the construction, testing, andmore » analysis of the Jet Propulsion Laboratory Mars Environmental Survey Lander; and finally led to the development of CAD based custom garment designs using 3D scanned images of the human body. The structural analysis of these fabric structures is described as well as a more traditional example Sandia with the test/analysis correlation of the impact of a weapon container.« less

Clinical Trials Reference Materials and Related Links | Division of Cancer Prevention

Cancer.gov

Agreements Clinical Trials Agreement Confidential Disclosure Agreements Cooperative Research and Development Agreement (CRADA) - Research Plan Financial and Staffing Contribution of the Parties Exception or Modifications to the CRADA Human Subject Protection/Informed Consent Tutorials (or Education) |

Command History OPNAV 5750-1, Fiscal Year 2004

DTIC Science & Technology

2006-05-04

Equipment allocation and distribution finalized. • 6-week plan developed for material production and testing. This project will have two primary...which has proven to be successful in the Navy’s past efforts to apply the proprietary technology to such materials as silicon- and carbon-based rubbers...and gels, epoxy resins, polyurethanes, etc. We will evaluate and select candidate materials and enlist the cooperation of suppliers and CRADA

Laser Drilling Development Trial Final Report CRADA No. TSB-1538-98

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hermann, M. R.; Hebbar, R. R.

This project performed various laser drilling tests to demonstrate femtosecond laser drilling of fuel injector nozzles with minimal recast, minimal heat affected zone and no collateral damage. LLNL had extensive experience in ultra short-pulse laser systems and developed specialized hardware for these applications.

3D Stacked Memory Final Report CRADA No. TC-0494-93

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bernhardt, A.; Beene, G.

TI and LLNL demonstrated: (1) a process for the fabrication of 3-D memory using stacked DRAM chips, and (2) a fast prototyping process for 3-D stacks and MCMs. The metallization to route the chip pads to the sides of the die was carried out in a single high-speed masking step. The mask was not the usual physical one in glass and chrome, but was simply a computer file used to control the laser patterning process. Changes in either chip or customer circuit-board pad layout were easily and inexpensively accommodated, so that prototyping was a natural consequence of the laser patterningmore » process. As in the current TI process, a dielectric layer was added to the wafer, and vias to the chip I/0 pads were formed. All of the steps in Texas Instruments earlier process that were required to gold bump the pads were eliminated, significantly reducing fabrication cost and complexity. Pads were created on the sides of ·the die, which became pads on the side of the stack. In order to extend the process to accommodate non-memory devices with substantially greater I/0 than is required for DRAMs, pads were patterned on two sides of the memory stacks as a proof of principle. Stacking and bonding were done using modifications of the current TI process. After stacking and bonding, the pads on the sides of the dice were connected by application of a polyimide insulator film with laser ablation of the polyimide to form contacts to the pads. Then metallization was accomplished in the same manner as on the individual die.« less

Development of Rotational Accelerometers Final Report CRADA No. TSB-2008-99

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hunter, S.; Crosson, R.

One of the difficulties in fabricating an inexpensive angular rate or rotation sensor is producing a device that is insensitive to acceleration, including the constant acceleration of gravity. The majority of rate sensors are either tuning fork type devices sensing a relatively weak force (i.e., Coriolis effect) and thus not very sensitive, or gyroscopes (either rotating or fiber optic based) that are large, consume lots of power and are expensive. This project was a collaborative effort between LLNL and The Fredericks Company to develop a rotational sensor as a standardized, commercial product. The Fredericks Company possessed expertise and capabilities inmore » the technical aspects of manufacturing this type of sensor, and they were interested in collaborating with LLNL to manufacture the rotational rate sensors as a commercial product.« less

Automotive Airbag Safety Enhancement Final Report CRADA No. TSB-1165-95

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cutting, Jack; Durrell, Robert

The Vehicle Safety systems (VSS) Division of Quantic Industries, Inc. (QII) manufactured automotive airbag components. When both the driver and the passenger side airbags inflated in a tightly sealed passenger compartment, the compression of the surrounding air could and, in some instances, would cause damage to the eardrums of the occupants. The Aerospace and Division (ADD) of QII had partially developed the technology to fracture the canopy of a jet aircraft at the time of pilot ejection. The technical problem was how to adapt the canopy fracturing technology to the rear window of a motor vehicle in a safe andmore » cost effective manner. The existing approach was to replace the embedded rear window defroster with a series-parallel network of exploding bridge wires (EBWs). This would still provide the defrost function at low voltage/ current, but would cause fracturing of the window when a high current/voltage pulse was applied without pyrotechnics or explosives. The elements of this system were the embedded EBW network and a trunk-mounted fireset. The fireset would store the required energy to fire the network upon the receipt of a trigger signal from the existing air bag crash sensor.« less

Breast Cancer Diagnostic System Final Report CRADA No. TC02098.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rubenchik, A. M.; DaSilva, L. B.

This was a collaborative effort between Lawrence Livermore National Security, LLC (formerly The Regents of the University of California)/Lawrence Liver more National Laboratory (LLNL) and BioTelligent, Inc. together with a Russian Institution (BioFil, Ltd.), to develop a new system ( diagnostic device, operating procedures, algorithms and software) to accurately distinguish between benign and malignant breast tissue (Breast Cancer Diagnostic System, BCDS).

ALPHA SMP SYSTEM(S) Final Report CRADA No. TC-1404-97

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seager, M.; Beaudet, T.

Within the scope of this subcontract, Digital Equipment Corporation (DIGITAL) and the University, through the Lawrence Livermore National Laboratory (LLNL), engaged in joint research and development activities of mutual interest and benefit. The primary objectives of these activities were, for LLNL to improve its capability to perform its mission, and for DIGITAL to develop technical capability complimentary to this mission. The collaborative activities had direct manpower investments by DIGITAL and LLNL. The project was divided into four areas of concern, which were handled concurrently. These areas included Gang Scheduling, Numerical Methods, Applications Development and Code Development Tools.

Mosaic Transparent Armor System Final Report CRADA No. TC02162.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kuntz, J. D.; Breslin, M.

This was a collaborative effort between Lawrence Livermore National Security, LLC as manager and operator of Lawrence Livermore National Laboratory (LLNL) and The Protective Group, Inc. (TPG) to improve the performance of the mosaic transparent armor system (MTAS) for transparent armor applications, military and civilian. LLNL was to provide the unique MTAS technology and designs to TPG for innovative construction and ballistic testing of improvements needed for current and near future application of the armor windows on vehicles and aircraft. The goal of the project was to advance the technology of MTAS to the point that these mosaic transparent windowsmore » would be introduced and commercially manufactured for military vehicles and aircraft.« less

Data Intensive Scientific Workflows on a Federated Cloud: CRADA Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garzoglio, Gabriele

The Fermilab Scientific Computing Division and the KISTI Global Science Experimental Data Hub Center have built a prototypical large-scale infrastructure to handle scientific workflows of stakeholders to run on multiple cloud resources. The demonstrations have been in the areas of (a) Data-Intensive Scientific Workflows on Federated Clouds, (b) Interoperability and Federation of Cloud Resources, and (c) Virtual Infrastructure Automation to enable On-Demand Services.

Digital X-Ray Imager Final Report CRADA No. TSB-1161-95

DOE Office of Scientific and Technical Information (OSTI.GOV)

Logan, C.; Toker, E.

The global objective of this cooperation was to lower the cost and improve the quality of breast health care in the United States. We planned to achieve it by designing a very high performance digital radiography unit for breast surgical specimen radiography in the operating room. These technical goals needed to be achieved at reasonable manufacturing costs to enable MedOptics to achieve high market penetration at a profit.

Rapidly Deployable Security System Final Report CRADA No. TC-2030-01

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kohlhepp, V.; Whiteman, B.; McKibben, M. T.

The ultimate objective of the LEADER and LLNL strategic partnership was to develop and commercialize_a security-based system product and platform for the use in protecting the substantial physical and economic assets of the government and commerce of the United States. The primary goal of this project was to integrate video surveillance hardware developed by LLNL with a security software backbone developed by LEADER. Upon completion of the project, a prototype hardware/software security system that is highly scalable was to be demonstrated.

New Aqueous Binders for Lithium-ion Batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jansen, Andrew N.; Krumdick, Gregory K.; Trask, Stephen E.

2016-12-22

This final report summarizes the research effort of the CRADA between PPG Industries and Argonne National Laboratory (CRADA # C1400501 and Amendment 1 - ACK 85C11, Rev. 1), and completes the requirements of Task #5 in the CRADA. The results from Argonne represent a combined effort between the MERF and CAMP Facility (Materials Engineering Research Facility and the Cell Analysis, Modeling and Prototyping Facility). The key points of this report can be briefly summarized as: The multicomponent aqueous binder for NCM cathodes developed by PPG shows promising results when used on the CAMP Facility’s pilot-scale coater; NCM523 cathode electrodes exposedmore » to water exhibit a voltage anomaly in the first two formation cycles that appears to have little effect on the material capacity, but needs to be explored further; the experimental LFP electrode produced by PPG does cycle electrochemically, but with reduced capacity and an uncharacteristic voltage profile; there is no obvious correlation between the pH and zeta-potential of materials that are commonly used in the lithium-ion battery; lithium ions are more readily dissolved out of NCM523 by water than the transition metals (by two orders of magnitude), and suggests that the plating bath may need to be spiked with a lithium salt; the approach of creating sub-micron size NCM523 particles via ball milling results in a cathode material with poor electrochemical performance.« less

High Efficiency Water Heating Technology Development Final Report. Part I, Lab/Field Performance Evaluation and Accelerated Life Testing of a Hybrid Electric Heat Pump Water Heater (HPWH)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baxter, Van D.; Murphy, Richard W.; Rice, C. Keith

DOE has supported efforts for many years with the objective of getting a water heater that uses heat pump technology (aka a heat pump water heater or HPWH) successfully on the residential equipment market. The most recent previous effort (1999-2002) produced a product that performed very well in ORNL-led accelerated durability and field tests. The commercial partner for this effort, Enviromaster International (EMI), introduced the product to the market under the trade name Watter$aver in 2002 but ceased production in 2005 due to low sales. A combination of high sales price and lack of any significant infrastructure for service aftermore » the sale were the principal reasons for the failure of this effort. What was needed for market success was a commercial partner with the manufacturing and market distribution capability necessary to allow economies of scale to lead to a viable unit price together with a strong customer service infrastructure. General Electric certainly meets these requirements, and knowing of ORNL s expertise in this area, approached ORNL with the proposal to partner in a CRADA to produce a high efficiency electric water heater. A CRADA with GE was initiated early in Fiscal Year, 2008. GE initially named its product the Hybrid Electric Water Heater (HEWH).« less

78 FR 50424 - NIH Cooperative Research and Development Agreement Program: Invitation To Solicit Nonclinical and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-19

...) Program. This CRADA Program is an extension of collaboration opportunities solicited by NIH or developed... health mission of the NIH. These collaboration opportunities are structured under the authority of 15 U.S... use of such additional information. The collaboration will be governed by CRADA terms that address...

76 FR 25362 - Cooperative Research and Development Agreement: Butanol Fuel Blend Usage With Marine Outboard...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-04

... participants would identify and investigate the advantages, disadvantages, required technology enhancements... Development Agreements (CRADAs), are authorized by the Federal Technology Transfer Act of 1986 (Pub. L. 99- 502, codified at 15 U.S.C. 3710(a)). A CRADA promotes the transfer of technology to the private sector...

77 FR 1708 - Cooperative Research and Development Agreement: Technology To Provide Wireless Precise Time...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-11

... determine the viability of certain wireless alternative timing approaches by conducting live, on-air tests... conducted from other sites as deemed necessary during CRADA testing. Reception of these test broadcasts are..., Test Plan, and Project Report for each phase of the CRADA work. We anticipate that the non-Federal...

Low Temperature Metal Coating Method Final Report CRADA No. TSB-1155-95

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kang, Sang-Wook; Gabel, Howard

A new metal coating method, cidled KEM (kinetic energy metal.lization), demonstrated in the laboratory by lnovati, utilized fast-moving solid particIes entrained in a gas that are caused to fiow through a nozzIe to effect particle deposition on metal surfaces at room temperature conditions. This method (US Patent 5,795,626) was an attractive and viabIe alternative to the currentIy available high-temperature coating methods avaiIabIe. Since it differs significantly from existing metal coating technologies, a brief description of the method is incIuded here. The proposed method, KEM, achieves cohesive and adhesive metallurgical bonding through the high-speed coUision of powder with a substrate andmore » the subsequent discharge of electrical charge at the substrate. Such coating is effected by entraining metal powder in a gas and accelerating this mixture through a supersonic nozzle. The gas/powder is directed towards the substrate to be coated. Collisions occur, initiaIly between the powder and the substrate, and, as the first Iayer of the coating forms, between the powder and the coating. During these collisions the powder is rapidly deformed, causing the exposure of fresh (oxide free) active metal surface. When these’active surfaces contact one another, they agglomerate and form true metaIIurgicaI bonds. The resultant coating has Iow porosity and high adhesive and cohesive strength. The formation of metaIIurgicaI bonds is potentiated by the discharge of electrical energy. This electrical energy is the result of triboeIectric charging of the particIes during acceleration and transit to the nozzIe. An advantage of the method is that it does not raise the temperature of the powder being appLiedor that of the substrate. Consequently, materials sensitive to high temperature may be applied without changing Me properties of the materkd or substrate.« less

Rapid tooling for functional prototyping of metal mold processes. CRADA final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zacharia, T.; Ludtka, G.M.; Bjerke, M.A.

1997-12-01

The overall scope of this endeavor was to develop an integrated computer system, running on a network of heterogeneous computers, that would allow the rapid development of tool designs, and then use process models to determine whether the initial tooling would have characteristics which produce the prototype parts. The major thrust of this program for ORNL was the definition of the requirements for the development of the integrated die design system with the functional purpose to link part design, tool design, and component fabrication through a seamless software environment. The principal product would be a system control program that wouldmore » coordinate the various application programs and implement the data transfer so that any networked workstation would be useable. The overall system control architecture was to be required to easily facilitate any changes, upgrades, or replacements of the model from either the manufacturing end or the design criteria standpoint. The initial design of such a program is described in the section labeled ``Control Program Design``. A critical aspect of this research was the design of the system flow chart showing the exact system components and the data to be transferred. All of the major system components would have been configured to ensure data file compatibility and transferability across the Internet. The intent was to use commercially available packages to model the various manufacturing processes for creating the die and die inserts in addition to modeling the processes for which these parts were to be used. In order to meet all of these requirements, investigative research was conducted to determine the system flow features and software components within the various organizations contributing to this project. This research is summarized.« less

Intelligent Manufacturing of Commercial Optics Final Report CRADA No. TC-0313-92

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taylor, J. S.; Pollicove, H.

The project combined the research and development efforts of LLNL and the University of Rochester Center for Manufacturing Optics (COM), to develop a new generation of flexible computer controlled optics· grinding machines. COM's principal near term development effort is to commercialize the OPTICAM-SM, a new prototype spherical grinding machine. A crucial requirement for commercializing the OPTICAM-SM is the development of a predictable and repeatable material removal process ( deterministic micro-grinding) that yields high quality surfaces that minimize non-deterministic polishing. OPTICAM machine tools and the fabrication process development studies are part of COM' s response to the DOD (ARPA) request tomore » implement a modernization strategy for revitalizing the U.S. optics manufacturing base. This project was entered into in order to develop a new generation of :flexible, computer-controlled optics grinding machines.« less

Scaleable production and separation of fermentation-derived acetic acid. Final CRADA report.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Snyder, S. W.; Energy Systems

2010-02-08

Half of U.S. acetic acid production is used in manufacturing vinyl acetate monomer (VAM) and is economical only in very large production plants. Nearly 80% of the VAM is produced by methanol carbonylation, which requires high temperatures and exotic construction materials and is energy intensive. Fermentation-derived acetic acid production allows for small-scale production at low temperatures, significantly reducing the energy requirement of the process. The goal of the project is to develop a scaleable production and separation process for fermentation-derived acetic acid. Synthesis gas (syngas) will be fermented to acetic acid, and the fermentation broth will be continuously neutralized withmore » ammonia. The acetic acid product will be recovered from the ammonium acid broth using vapor-based membrane separation technology. The process is summarized in Figure 1. The two technical challenges to success are selecting and developing (1) microbial strains that efficiently ferment syngas to acetic acid in high salt environments and (2) membranes that efficiently separate ammonia from the acetic acid/water mixture and are stable at high enough temperature to facilitate high thermal cracking of the ammonium acetate salt. Fermentation - Microbial strains were procured from a variety of public culture collections (Table 1). Strains were incubated and grown in the presence of the ammonium acetate product and the fastest growing cultures were selected and incubated at higher product concentrations. An example of the performance of a selected culture is shown in Figure 2. Separations - Several membranes were considered. Testing was performed on a new product line produced by Sulzer Chemtech (Germany). These are tubular ceramic membranes with weak acid functionality (see Figure 3). The following results were observed: (1) The membranes were relatively fragile in a laboratory setting; (2) Thermally stable {at} 130 C in hot organic acids; (3) Acetic acid rejection > 99%; and (4) Moderate ammonia flux. The advantages of producing acetic acid by fermentation include its appropriateness for small-scale production, lower cost feedstocks, low energy membrane-based purification, and lower temperature and pressure requirements. Potential energy savings of using fermentation are estimated to be approximately 14 trillion Btu by 2020 from a reduction in natural gas use. Decreased transportation needs with regional plants will eliminate approximately 200 million gallons of diesel consumption, for combined savings of 45 trillion Btu. If the fermentation process captures new acetic acid production, savings could include an additional 5 trillion Btu from production and 7 trillion Btu from transportation energy.« less

Development of DNA Pillar Chip Final Report CRADA No. TSB-2035-01

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ness, K. D.; Long, G. W.

This was a collaborative effort between The Regents of the University of California, Lawrence Livermore National Laboratory (LLNL) and Tetracore, to demonstrate a proof of principal device for the capture and controlled release of DNA moving within a flow stream.

Solidification Technologies for Radioactive and Chemical Liquid Waste Treatment - Final CRADA Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Castiglioni, Andrew J.; Gelis, Artem V.

This project, organized under DOE/NNSA's Global Initiatives for Proliferation Prevention program, joined Russian and DOE scientists in developing more effective solidification and storage technologies for liquid radioactive waste. Several patent applications were filed by the Russian scientists (Russia only) and in 2012, the technology developed was approved by Russia's Federal State Unitary Enterprise RADON for application throughout Russia in cleaning up and disposing of radioactive waste.

Technology Assessment for Powertrain Components Final Report CRADA No. TC-1124-95

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tokarz, F.; Gough, C.

LLNL utilized its defense technology assessment methodologies in combination with its capabilities in the energy; manufacturing, and transportation technologies to demonstrate a methodology that synthesized available but incomplete information on advanced automotive technologies into a comprehensive framework.

Electromagnetic Simulations for Aerospace Application Final Report CRADA No. TC-0376-92

DOE Office of Scientific and Technical Information (OSTI.GOV)

Madsen, N.; Meredith, S.

Electromagnetic (EM) simulation tools play an important role in the design cycle, allowing optimization of a design before it is fabricated for testing. The purpose of this cooperative project was to provide Lockheed with state-of-the-art electromagnetic (EM) simulation software that will enable the optimal design of the next generation of low-observable (LO) military aircraft through the VHF regime. More particularly, the project was principally code development and validation, its goal to produce a 3-D, conforming grid,time-domain (TD) EM simulation tool, consisting of a mesh generator, a DS13D-based simulation kernel, and an RCS postprocessor, which was useful in the optimization ofmore » LO aircraft, both for full-aircraft simulations run on a massively parallel computer and for small scale problems run on a UNIX workstation.« less

LST CGM Generator and Viewer Final Report CRADA No. TSB-1558-98

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vickers, Don; Larson, Don

The purpose of this project was to jointly develop and test a software plug-in that would convert native Pro /ENGINEER digital engineering drawings to Computer Graphics Metafile (CGM) format. If it was not feasible to convert the Pro/ENGINEER files, we planned to develop and test a similar conversion of native AutoCAD engineering drawings to CGM. CGM viewer plug-ins were developed as needed. There were four main tasks in this project: 1. Requirements for CGM Plug-in 2. Product Evaluation 3. Product Development Feasibility Study 4. Developing a "Plug-In" Application.

Chemical and Mechanical Characterization of Diamond-Like Carbon Hard Coatings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Poker, D B; Doughty, C

1999-12-28

This CRADA was intended to investigate and optimize the process used by ASTEX-PlasmaQuest for deposition of diamond-like carbon films. Approval for funding was delayed, and an unexpected move of the PlasmaQuest headquarters and research facilities prevented appropriate samples from being prepared before the end of the CRADA. Therefore, No effort was expended under this program.

Control Strategies for HCCI Mixed-Mode Combustion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wagner, Robert M; Edwards, Kevin Dean

2010-03-01

Delphi Automotive Systems and ORNL established this CRADA to expand the operational range of Homogenous Charge Compression Ignition (HCCI) mixed-mode combustion for gasoline en-gines. ORNL has extensive experience in the analysis, interpretation, and control of dynamic engine phenomena, and Delphi has extensive knowledge and experience in powertrain compo-nents and subsystems. The partnership of these knowledge bases was important to address criti-cal barriers associated with the realistic implementation of HCCI and enabling clean, efficient operation for the next generation of transportation engines. The foundation of this CRADA was established through the analysis of spark-assisted HCCI data from a single-cylinder research engine.more » This data was used to (1) establish a conceptual kinetic model to better understand and predict the development of combustion instabilities, (2) develop a low-order model framework suitable for real-time controls, and (3) provide guidance in the initial definition of engine valve strategies for achieving HCCI operation. The next phase focused on the development of a new combustion metric for real-time characterization of the combustion process. Rapid feedback on the state of the combustion process is critical to high-speed decision making for predictive control. Simultaneous to the modeling/analysis studies, Delphi was focused on the development of engine hardware and the engine management system. This included custom Delphi hardware and control systems allowing for flexible control of the valvetrain sys-tem to enable HCCI operation. The final phase of this CRADA included the demonstration of conventional and spark assisted HCCI on the multi-cylinder engine as well as the characterization of combustion instabilities, which govern the operational boundaries of this mode of combustion. ORNL and Delphi maintained strong collaboration throughout this project. Meetings were held on a bi-weekly basis with additional reports

Epileptic Seizure Forewarning by Nonlinear Techniques

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hively, L.M.

2002-04-19

This report describes work that was performed under a Cooperative Research and Development Agreement (CRADA) between UT-Battelle, LLC (Contractor) and a commercial participant, VIASYS Healthcare Inc. (formerly Nicolet Biomedical, Inc.). The Contractor has patented technology that forewarns of impending epileptic events via scalp electroencephalograph (EEG) data and successfully demonstrated this technology on 20 datasets from the Participant under pre-CRADA effort. This CRADA sought to bridge the gap between the Contractor's existing research-class software and a prototype medical device for subsequent commercialization by the Participant. The objectives of this CRADA were (1) development of a combination of existing computer hardware andmore » Contractor-patented software into a clinical process for warning of impending epileptic events in human patients, and (2) validation of the epilepsy warning methodology. This work modified the ORNL research-class FORTRAN for forewarning to run under a graphical user interface (GUI). The GUI-FORTRAN software subsequently was installed on desktop computers at five epilepsy monitoring units. The forewarning prototypes have run for more than one year without any hardware or software failures. This work also reported extensive analysis of model and EEG datasets to demonstrate the usefulness of the methodology. However, the Participant recently chose to stop work on the CRADA, due to a change in business priorities. Much work remains to convert the technology into a commercial clinical or ambulatory device for patient use, as discussed in App. H.« less

Evaluating lake phytoplanton response to human disturbance and climate change using satellite imagery

NASA Astrophysics Data System (ADS)

Novitski, Linda Nicole

Accurate and cost-effective assessment of water quality is necessary for proper management and restoration of inland water bodies susceptible to algal bloom conditions. Landsat and MODIS satellite images were used to create chlorophyll and Secchi depth predictive models for algal assessment of Great Lakes and other lakes of the United States. Boosted regression tree (BRT) models using satellite imagery are both easy to use and can have high predictive performance. BRT models inferred chlorophyll and Secchi depth more accurately than linear regression models for all study locations. Inferred chlorophyll of inner Saginaw Bay was subsequently used in ecological models to help understand the ecological drivers of algal blooms in this ecosystem. For small lakes (non-Great Lakes), the best national Landsat model for ln-transformed chlorophyll was the BRT model and had a cross-validation R 2 of 0.44 and a 0.76 ln-transformed mug/L RMSE. The best national Landsat model for Secchi depth was also a BRT model that had an adjusted R 2 of 0.52 and a 0.80 m RMSE. We assessed the applicability of the national chlorophyll model for ecological analysis by comparing the total phosphorus- chlorophyll relationship with chlorophyll determined from sampling or remote sensing, which showed the total phosphorus- chlorophyll relationship had an adjusted R2 = 0.58 and 1.02 ln-transformed microg/L RMSE with sampled chlorophyll versus an adjusted R2 = 0.56 and 1.04 ln-transformed mug/L RMSE with chlorophyll determined by the boosted regression tree remote sensing model. For Great Lakes models, the MODIS BRT model predicted chlorophyll most accurately of the three BRT models and compared well to other models in the literature. BRT models for Landsat ETM+ and TM more accurately predicted chlorophyll than the MSS model and all Landsat models had favorable results when compared to the literature. BRT chlorophyll predictive models are useful in helping to understand historical, long

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tiegs, T.N.

The Cooperative Research and Development Agreement (CRADA) was to develop composites of TiC-Ni{sub 3}Al with refined grain microstructures for application in diesel engine fuel injection devices. Grain refinement is important for improved wear resistance and high strength for the applications of interest. Attrition milling effectively reduces the initial particle size and leads to a reduction of the final grain size. However, an increase in the oxygen content occurs concomitantly with the grinding operation and decreased densification of the compacts occurs during sintering.

Report to Congress on the Activities of the DoD Office of Technology Transition

DTIC Science & Technology

2006-08-01

a 4:1 return- on -investment (ROI) to DoD from licensing revenues, CRADAs, and other partnerships. In addition, the ...nutritional high energy bar for the troops. The result was the “HooAH!” bar. Based on an invention at Natick and through a CRADA with MGM Mars, inc...production capacities for high performance RH microprocessors with a progression from radiation tolerant to radiation

Airport Activity Statistics of Certified Route Air Carriers: Calendar Year 1991

DTIC Science & Technology

1991-12-31

M otitpeilier/Barre Battle Creek, Ml . ...... .... ...... .................... ... Kalamazoo/Battle Creek Bay City. M l...Saginaw,/ Bay City/M idland Beaufori. NC...Green Bay /Clintonville Cody, WY................................................ . .. . .. .. . .. . .. . Lovell/ Powell[/Codyv Coffeyville

Regional Anesthesia and Valproate Sodium for the Prevention of Chronic Post-Amputation Pain

DTIC Science & Technology

2014-10-01

and meetings with VAMC nursing and all study personnel while awaiting CRADA approval from VAMC NOVEMBER Duke/VA CRADA approved; start of enrollment at...Duke patient enrollment MAY Numerous meetings at Duke (Investigational Drug Service, Limb Loss Clinical Nurse Specialist, in-patient team) to discuss...Dionne Apedjihoun, CRC met with Nancy Payne, Duke Clinical Nurse /Limb Loss Specialist to trouble shoot potential patient recruitment for in and out

Predictive Engineering Tools for Injection-Molded Long-Carbon-Fiber Thermoplastic Composites - FY13 Third Quarterly Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nguyen, Ba Nghiep; Simmons, Kevin L.

2013-08-06

This quarterly report summarizes the status for the project planning to obtain all the approvals required for a Cooperative Research and Development Agreement (CRADA) with Autodesk, Inc., Toyota Motor Engineering and Manufacturing North America (Toyota), and Magna Exterior and Interiors Corporation (Magna). The CRADA documents have been processed by PNNL Legal Services that is also coordinating the revision effort with the industrial parties to address DOE’s comments.

Technology Transfer Opportunities: On-Demand Printing in Support of National Geospatial Data

USGS Publications Warehouse

,

1997-01-01

The U.S. Geological Survey (USGS) and the 3M Company of St. Paul, Minnesota, have entered into a cooperative research and development agreement (CRADA) to investigate maps-on-demand technology to support the production of USGS mapping products. The CRADA will potentially help the USGS to develop on-demand alternatives to lithographic maps and help 3M to develop a series of commercial instant map-printing systems.

Method for Processing Liver Spheroids Using an Automatic Tissue Processor

DTIC Science & Technology

2016-05-01

Harry; Kristovich, Robert L. (ECBC); and Valdes, Leah R. (ORISE) 5d. PROJECT NUMBER CRADA 1314C w/ Wake Forest University 5e. TASK NUMBER 5f. WORK...The work described in this report was authorized under project no. CRADA1314C with Wake Forest University Health Sciences. The work was started in... Wake Forest Institute for Regenerative Medicine Winston-Salem, NC iv Blank v CONTENTS 1. INTRODUCTION

Evaluation of Aerogel Clad Optical Fibers Final Report CRADA No. TSB-1448-97

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maitland, Duncan; Droege, M. W.

Fiber-optic based sensors will be needed for in situ monitoring of degradation products in various components of nuclear weapons. These sensors typically consist of a transducer located at the measurement site whose optical properties are modulated by interaction with the targeted degradation product. The interrogating light source and the detector for determining sensor response are located remotely. These two subsystems are connected by fiber optic cables. LLNL has developed a new technology, aerogel clad optical fibers, that have the advantage of accepting incident rays over a much wider angular range than normal glass clad fibers. These fibers are also capablemore » of transmitting light more efficiently. These advantages can lead to a factor of 2-4 improvement in sensitivity and detection limit.« less

Investigation of the fundamentals of low-energy nanosecond pulse ignition: Final CRADA Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wallner, Thomas; Scarcelli, Riccardo; Zhang, Anqi

A detailed investigation of the fundamentals of low-energy nanosecond pulse ignition was performed with the objective to overcome the barrier presented by limited knowledge and characterization of nonequilibrium plasma ignition for realistic internal combustion engine applications (be it in the automotive or power generation field) and shed light on the mechanisms which improve the performance of the advanced TPS ignition system compared to conventional state-of-the-art hardware. Three main tasks of the research included experimental evaluation on a single-cylinder automotive gasoline engine, experimental evaluation on a single-cylinder stationary natural gas engine and energy quantification using x-ray diagnostics.

Advanced Magnetic Head Development Revision 1 Final Report CRADA No. TC-0840-94

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cerjan, C.; Shi, S.

The specific go,il of this research was the development of a prototype read magnetic sensor head using the Current:Perpendicular-to-Plane (CPP) geometry with known GMR (Giant Magneto-Resistive) multilayered structures to achieve read densities greater than 10 Gbit/in2, field sensitivities greater than 1%/Oe, switching fields less than 20 Oe, and total MR response greater than 10%. The specific materials needed for this idcnl behavior had to be determined, as did the eventual design of the sensor (placement of contact leads, shields, and biasing magnets). Thus the thrust of the rescnrch required a search for the proper multilayer material combination und the developmentmore » of a simulation capability to guide sensor design. Issues i:elated to device integration, such as media noise and lead contact resistance, were also recognized as important technological hurdles but these items were deferred until the operating conditions of the-prototype GMR sensor were more precisely determined.« less

Brandon Research, Inc. Orthopedic Implant Cooperative Research and Development Agreement (CRADA) Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Freeman, W.R.

1999-04-22

The project was a joint research effort between the U. S. Department of Energy's (DOE) Kansas City Plant (KCP) and Brandon Research, Inc. to develop ways to improve implants used for orthopedic surgery for joint replacement. The primary product produced by this study is design information, which may be used to develop implants that will improve long-term fixation and durability in the host bone environment.

Development of an Opto-Acoustic Recanalization System Final Report CRADA No. 1314-96

DOE Office of Scientific and Technical Information (OSTI.GOV)

Silva, L. D.; Adam, H. R.

The objective of the project was to develop an ischemic stroke treatient system that restores blood flow to the brain by removing occlusions using acoustic energy created by fiber optic delivery of laser light, a process called Opto Acoustic Recanalization (OAR). The key tasks of the project were to select a laser system, quantify temperature, pressure and particle size distribution, and develop a prototype device incorporating a feedback mechanism. System parameters were developed to cause emulsification while attempting to minimize particle size and collateral damage. The prototype system was tested in animal models and resulted in no visible collateral damage.

Laser Texturing of Magnetic Recording Media Final Report CRADA No. TSV-1298-96

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hackel, L.; Marshall, A.

The Commercial Laser Systems Group at LLNL developed a concept for patterning of computer magnetic recording discs. Magnetic recording media require texturing over areas designated for contact in order to minimize friction with data transducing heads. In fabricating a hard disk, an aluminum nickel-phosphorous substrate was polished to a specular finish then a mechanical means was used to roughen an annular area intended to be the head contact band. In a previous patent (US Patent 5,062,021) it was proposed that the focused output of a low power laser with short pulse length could be used to generate the textured pattern.more » However, the patterned area typically required 75,000 textured spots that needed to be rapidly (less than 10 seconds) printed with good uniformity. A means to achieve the accurate placement and uniform profile, as well as a meaningfully rapid process time, was not discussed in the referenced patent. The LLNL team devised a system that could rapidly and inexpensively accomplish the texturing.« less

Image Matrix Processor for Volumetric Computations Final Report CRADA No. TSB-1148-95

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roberson, G. Patrick; Browne, Jolyon

The development of an Image Matrix Processor (IMP) was proposed that would provide an economical means to perform rapid ray-tracing processes on volume "Giga Voxel" data sets. This was a multi-phased project. The objective of the first phase of the IMP project was to evaluate the practicality of implementing a workstation-based Image Matrix Processor for use in volumetric reconstruction and rendering using hardware simulation techniques. Additionally, ARACOR and LLNL worked together to identify and pursue further funding sources to complete a second phase of this project.

Maintenance Dredging of the Federal Navigation Channels in the Saginaw River and Saginaw Bay, Michigan.

DTIC Science & Technology

1975-12-01

contact is Dr. Martha Bigelow, Director, Michigan History Division, Depar=int of State, Lansing, Michigan 48918. Te National Recister shoeuld also be...other low growth. Methylation - Change from an inorganic to an organic form usually as a result of bacterial action. For * example, the metal mercury

Visual observations of historical lake trout spawning grounds in western Lake Huron

USGS Publications Warehouse

Nester, Robert T.; Poe, Thomas P.

1987-01-01

Direct underwater video observations were made of the bottom substrates at 12 spawning grounds formerly used by lake trout Salvelinus namaycush in western Lake Huron to evaluate their present suitability for successful reproduction by lake trout. Nine locations examined north of Saginaw Bay in the northwestern end of the lake are thought to provide the best spawning habitat. The substrate at these sites consisted of angular rough cobble and rubble with relatively deep interstitial spaces (a?Y 0.5 m), small amounts of fine sediments, and little or no periphytic growth. Conditions at the three other sampling locations south of Saginaw Bay seemed much less suitable for successful reproduction based on the reduced area of high-quality substrate, shallow interstitial spaces, high infiltration of fine sediments, and greater periphytic growth.

Ground-water levels in Huron County, Michigan, 2002-03

USGS Publications Warehouse

Weaver, T.L.; Blumer, S.P.; Crowley, S.L.

2008-01-01

Lake Huron (National Oceanic and Atmospheric Administration, 2003; 2004). The net decline in the water level of Lake Huron from January 1, 2002 to December 31, 2003 was about 0.3 ft. Annual precipitation in 2002 was about 0.3 inches above normal, with much of it occurring during summer months. The provisional precipitation total for 2003 is about an inch below normal (NOAA, 2003, 2004; Danny Costello, NOAA hydrologist, written commun., 2003, 2004).Four wells equipped with continuous-data recorders are completed in the glacial, Saginaw, and Marshall aquifers. Water levels in three of the four wells equipped with continuous-data recorders experienced a net decline over the period from January 2002 to December 2003, while the level in well H9r, completed in the Saginaw aquifer in Fairhaven Township adjacent to Saginaw Bay (Lake Huron), rose about 1.3 ft over the same period. Interestingly, the water level in Saginaw Bay declined about 0.3 ft over the same period. A period-ofrecord maximum depth to water was recorded in September 2003 in well H25Ar, completed in the Marshall aquifer in Lake Township. Hydrographs showing altitude of the water surface are presented for each of four wells equipped with continuous-data recorders.Twenty three wells were measured on a quarterly basis in 2002-03. These wells are completed in the Saginaw and Marshall aquifers, and Coldwater confining unit. Although each quarterly measurement only provides a “snapshot” water level, the data adequately define the “generalized” water-level trend in the aquifer near the well. The water level in one quarterly-measured well completed in the Saginaw aquifer near Saginaw Bay, had a net rise for the period from January 2002 to December 2003, while levels in the other 22 quarterly-measured wells declined about 0.5 to 2.0 ft during the same period. A period-of-record minimum depth to water (high) was measured in 2002 in two quarterly-measured wells completed in the Saginaw aquifer, although the level

Seasonal thermal ecology of adult walleye (Sander vitreus) in Lake Huron and Lake Erie.

PubMed

Peat, Tyler B; Hayden, Todd A; Gutowsky, Lee F G; Vandergoot, Christopher S; Fielder, David G; Madenjian, Charles P; Murchie, Karen J; Dettmers, John M; Krueger, Charles C; Cooke, Steven J

2015-10-01

The purpose of this study was to characterize thermal patterns and generate occupancy models for adult walleye from lakes Erie and Huron with internally implanted biologgers coupled with a telemetry study to assess the effects of sex, fish size, diel periods, and lake. Sex, size, and diel periods had no effect on thermal occupancy of adult walleye in either lake. Thermal occupancy differed between lakes and seasons. Walleye from Lake Erie generally experienced higher temperatures throughout the spring and summer months than did walleye in Lake Huron, due to limnological differences between the lakes. Tagged walleye that remained in Saginaw Bay, Lake Huron (i.e., adjacent to the release location), as opposed to those migrating to the main basin of Lake Huron, experienced higher temperatures, and thus accumulated more thermal units (the amount of temperature units amassed over time) throughout the year. Walleye that migrated toward the southern end of Lake Huron occupied higher temperatures than those that moved toward the north. Consequently, walleye that emigrated from Saginaw Bay experienced thermal environments that were more favorable for growth as they spent more time within their thermal optimas than those that remained in Saginaw Bay. Results presented in this paper provide information on the thermal experience of wild fish in a large lake, and could be used to refine sex- and lake-specific bioenergetics models of walleye in the Great Lakes to enable the testing of ecological hypotheses. Copyright © 2015 Elsevier Ltd. All rights reserved.

Seasonal thermal ecology of adult walleye (Sander vitreus) in Lake Huron and Lake Erie

USGS Publications Warehouse

Peat, Tyler B; Hayden, Todd A.; Gutowsky, Lee F G; Vandergoot, Christopher S.; Fielder, David G.; Madenjian, Charles P.; Murchie, Karen J; Dettmers, John M.; Krueger, Charles C.; Cooke, Steven J.

2015-01-01

The purpose of this study was to characterize thermal patterns and generate occupancy models for adult walleye from lakes Erie and Huron with internally implanted biologgers coupled with a telemetry study to assess the effects of sex, fish size, diel periods, and lake. Sex, size, and diel periods had no effect on thermal occupancy of adult walleye in either lake. Thermal occupancy differed between lakes and seasons. Walleye from Lake Erie generally experienced higher temperatures throughout the spring and summer months than did walleye in Lake Huron, due to limnological differences between the lakes. Tagged walleye that remained in Saginaw Bay, Lake Huron (i.e., adjacent to the release location), as opposed to those migrating to the main basin of Lake Huron, experienced higher temperatures, and thus accumulated more thermal units (the amount of temperature units amassed over time) throughout the year. Walleye that migrated toward the southern end of Lake Huron occupied higher temperatures than those that moved toward the north. Consequently, walleye that emigrated from Saginaw Bay experienced thermal environments that were more favorable for growth as they spent more time within their thermal optimas than those that remained in Saginaw Bay. Results presented in this paper provide information on the thermal experience of wild fish in a large lake, and could be used to refine sex- and lake-specific bioenergetics models of walleye in the Great Lakes to enable the testing of ecological hypotheses.

TECHNOLOGIES FOR MONITORING AND MEASUREMENT OF DIOXIN AND DIOXIN-LIKE COMPOUNDS IN SOIL AND SEDIMENT. HYBRIZYME CORPORATION AHRC PCR KIT

EPA Science Inventory

A demonstration of technologies for determining the presence of dioxin and dioxin-like compounds in soil and sediment was conducted under EPA's Superfund Innovative Technology Evaluation Program in Saginaw, Michigan in April 2004. This report describes the performance evaluation ...

DEMONSTRATION AND QUALITY ASSURANCE PROJECT PLAN TECHNOLOGIES FOR THE MONITORING AND MEASUREMENT OF DIOXIN AND DIOXIN-LIKE COMPOUNDS IN SOIL AND SEDIMENT

EPA Science Inventory

The demonstration of technologies for determining the presence of dioxin in soil and sediment is being conducted under the U.S. Environmental Protection Agency Superfund Innovative Technology Evaluation Program in Saginaw, Michigan, at Green Point Environmental Learning Center fr...

TECHNOLOGIES FOR MONITORING AND MEASUREMENT OF DIUOXIN AND DIOXIN-LIKE COMPOUNDS IN SOIL AND SEDIMENT. ABRAXIS LLC COPLANAR PCB ELISA KIT

EPA Science Inventory

A demonstration of technologies for determining the presence of dioxin and dioxin-like compounds in soil and sediment was conducted under EPA's Superfund Innovative Technology Evaluation Program in Saginaw, Michigan in April 2004. This report describes the performance evaluation ...

INTERIM REPORT ON THE EVOLUTION AND PERFORMANCE OF THE EICHROM TECHNOLOGIES PROCEPT RAPID DIOXIN ASSAY FOR SOIL AND SEDIMENT SAMPLES

EPA Science Inventory

A demonstration of screening technologies for determining the presence of dioxin and dioxin-like compounds in soil and sediment was conducted under the U.S. Environmental Protection Agency's(EPA's) Superfund Innovative Technology Evaluation Program in Saginaw, Michigan in 2004. T...

Beta PIs from the USDA-ARS NPGS evaluated for resistance to Cercospora beticola, 2013

USDA-ARS?s Scientific Manuscript database

Thirty-one Plant Introductions (PIs) from the USDA-ARS National Plant Germplasm System were evaluated for resistance to Cercospora beticola in an artificially produced epiphytotic at the Saginaw Valley Research and Extension Center near Frankenmuth, Michigan. Internal controls included a susceptibl...

Beta PIs from the USDA-ARS NPGS evaluated for resistance to Cercospora beticola, 2014

USDA-ARS?s Scientific Manuscript database

Thirty Plant Introductions (PIs) from the USDA-ARS National Plant Germplasm System were evaluated for resistance to Cercospora beticola in an artificially produced epiphytotic at the Saginaw Valley Research and Extension Center near Frankenmuth, Michigan. Internal controls included a susceptible, '...

Beta PIs from the USDA-ARS NPGS evaluated for resistance to Cercospora beticola, 2011

USDA-ARS?s Scientific Manuscript database

Thirty Plant Introductions (PIs) from the USDA-ARS National Plant Germplasm System were evaluated for resistance to Cercospora beticola in an artificially produced epiphytotic at the Saginaw Valley Research and Extension Center near Frankenmuth, MI. Internal controls included a susceptible commercia...

Beta PIs From the USDA-ARS NPGS Evaluated for Resistance to Cercospora beticola, 2009

USDA-ARS?s Scientific Manuscript database

Thirty Plant Introductions (PIs) from the USDA-ARS National Plant Germplasm System were evaluated for resistance to Cercospora beticola in an artificially produced epiphytotic at the Saginaw Valley Research Farm near Frankenmuth, MI. Internal controls included a susceptible commercial variety, CE, ...

Beta PIs from the USDA-ARS NPGS evaluated for resistance to Cercospora beticola, 2012

USDA-ARS?s Scientific Manuscript database

Thirty Plant Introductions (PIs) from the USDA-ARS National Plant Germplasm System were evaluated for resistance to Cercospora beticola in an artificially produced epiphytotic at the Saginaw Valley Research and Extension Center near Frankenmuth, MI. Internal controls included a susceptible germplas...

Beta PIs from the USDA-ARS NPGS evaluated for resistance to Cercospora beticola, 2010

USDA-ARS?s Scientific Manuscript database

Thirty Plant Introductions (PIs) from the USDA-ARS National Plant Germplasm System were evaluated for resistance to Cercospora beticola in an artificially produced epiphytotic at the Saginaw Valley Research and Extension Center near Frankenmuth, MI. Internal controls included a susceptible commercia...

PERFORMANCE OF THE CAPE TECHNOLOGIES DF1 DIOXIN/FURAN IMMUNOASSAY KIT FOR SOIL AND SEDIMENT SAMPLES

EPA Science Inventory

A demonstration of screening technologies for determining the presence of dioxin and dioxin-like compounds in soil and sediment was conducted under the U.S. Environmental Protection Agency’s (EPA’s) Superfund Innovative Technology Evaluation Program in Saginaw, Michigan in 2004. ...

Development of CVD Diamond for Industrial Applications Final Report CRADA No. TC-2047-02

DOE Office of Scientific and Technical Information (OSTI.GOV)

Caplan, M.; Olstad, R.; Jory, H.

2017-09-08

This project was a collaborative effort to develop and demonstrate a new millimeter microwave assisted chemical vapor deposition(CVD) process for manufacturing large diamond disks with greatly reduced processing times and costs from those now available. In the CVD process, carbon based gases (methane) and hydrogen are dissociated into plasma using microwave discharge and then deposited layer by layer as polycrystalline diamond onto a substrate. The available low frequency (2.45GHz) microwave sources used elsewhere (De Beers) result in low density plasmas and low deposition rates: 4 inch diamond disks take 6-8 weeks to process. The new system developed in this projectmore » uses a high frequency 30GHz Gyrotron as the microwave source and a quasi-optical CVD chamber resulting in a much higher density plasma which greatly reduced the diamond processing times (1-2 weeks)« less

Numerical Simulations of 3D Seismic Data Final Report CRADA No. TC02095.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Friedmann, S. J.; Kostov, C.

This was a collaborative effort between Lawrence Livermore National Security, LLC (formerly The Regents of the University of Califomia)/Lawrence-Livermore National Laboratory (LLNL) and Schlumberger Cambridge Research (SCR), to develop synthetic seismic data sets and supporting codes.

Ceramic High Efficiency Particulate Air (HEPA) Filter Final Report CRADA No. TC02160.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mitchell, M.; Bergman, W.

2017-08-25

The technical objective of this project was to develop a ceramic HEPA filter technology, by initially producing and testing coupon ceramics, small scale prototypes, and full scale prototype HEPA filters, and to address relevant manufacturing and commercialization technical issues.

Winnebago Resource Study. Cooperative Research and Development Final Report, CRADA Number CRD-09-329

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jimenez, A.; Robichaud, R.

2015-03-01

Since 2005 the NREL Native American Tall Tower Loan program has assisted Native American tribes to assess their wind resource by lending tall (30m - 50m) anemometer. This program has allowed tribes a lower risk way to gather financeable wind data for potential utility scale wind energy projects. These projects offer Tribes a significant economic development opportunity.

Monolithic circuits for barium fluoride detectors used in nuclear physics experiments. CRADA final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Varner, R.L.; Blankenship, J.L.; Beene, J.R.

1998-02-01

Custom monolithic electronic circuits have been developed recently for large detector applications in high energy physics where subsystems require tens of thousands of channels of signal processing and data acquisition. In the design and construction of these enormous detectors, it has been found that monolithic circuits offer significant advantages over discrete implementations through increased performance, flexible packaging, lower power and reduced cost per channel. Much of the integrated circuit design for the high energy physics community is directly applicable to intermediate energy heavy-ion and electron physics. This STTR project conducted in collaboration with researchers at the Holifield Radioactive Ion Beammore » Facility (HRIBF) at Oak Ridge National Laboratory, sought to develop a new integrated circuit chip set for barium fluoride (BaF{sub 2}) detector arrays based upon existing CMOS monolithic circuit designs created for the high energy physics experiments. The work under the STTR Phase 1 demonstrated through the design, simulation, and testing of several prototype chips the feasibility of using custom CMOS integrated circuits for processing signals from BaF{sub 2} detectors. Function blocks including charge-sensitive amplifiers, comparators, one shots, time-to-amplitude converters, analog memory circuits and buffer amplifiers were implemented during Phase 1 effort. Experimental results from bench testing and laboratory testing with sources were documented.« less

Ceramic High Efficiency Particulate Air (HEPA) Filter Final Report CRADA No. TC02102.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mitchell, M.; Morse, T.

This was a collaborative effort between Lawrence Livermore National Security, LLC (formerly The Regents of the University of California)/Lawrence Livermor e National Laboratory (LLNL) and Flanders-Precisionaire (Flanders), to develop ceramic HEP A filters under a Thrust II Initiative for Proliferation Prevention (IPP) project. The research was conducted via the IPP Program at Commonwe alth of Independent States (CIS) Institutes, which are handled under a separate agreement. The institutes (collectively referred to as "CIS Institutes") involved with this project were: Bochvar: Federal State Unitarian Enterprise All-Russia Scientific and Research Institute of Inorganic Materials (FSUE VNIINM); Radium Khlopin: Federal State Unitarian Enterprisemore » NPO Radium Institute named (FSUE NPO Radium Institute); and Bakor: Science and Technology Center Bakor (STC Bakor).« less

Algorithms and Architectures for Elastic-Wave Inversion Final Report CRADA No. TC02144.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Larsen, S.; Lindtjorn, O.

2017-08-15

This was a collaborative effort between Lawrence Livermore National Security, LLC as manager and operator of Lawrence Livermore National Laboratory (LLNL) and Schlumberger Technology Corporation (STC), to perform a computational feasibility study that investigates hardware platforms and software algorithms applicable to STC for Reverse Time Migration (RTM) / Reverse Time Inversion (RTI) of 3-D seismic data.

Interventional Application of Shape Memory Polymer Foam Final Report CRADA No. TC-02067-03

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maitland, D.; Metzger, M. F.

This was a collaborative effort between The Regents of the University of California, Lawrence Livermore National Laboratory (LLNL) and Sierra Interventions, LLC, to develop shape memory polymer foam devices for treating hemorrhagic stroke.

Electron-Beam Vapor Deposition of Mold Inserts Final Report CRADA No. TSB-777-94

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shepp, T.; Feeley, T.

Lawrence Livermore National Laboratory and H.G.G. Laser Fare, Inc. studied the application of electron-beam vapor deposition technology to the production of mold inserts for use in an injection molding machine by Laser Fare. Laser Fare provided LLNL with the requirements of the mold inserts as well as sample inserts. LLNL replicated the mold insert(s) to Laser Fare for testing by Laser Fare.

Optical Encoding Technology for Viral Screening Panels Final Report CRADA No TC02132.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lenhoff, R.; Haushalter, R.

This was a collaborative effort between Lawrence Livermore National Security, LLC, Lawrence Livermore National Laboratory (LLNL) and Parallel Synthesis Technologies, Inc. (PSTI), to develop Optical Encoding Technology for Viral Screening Panels. The goal for this effort was to prepare a portable bead reader system that would enable the development of viral and bacterial screening panels which could be used for the detection of any desired set of bacteria or viruses in any location. The main objective was to determine if the combination of a bead-based, PCR suspension array technology, formulated from Parallume encoded beads and PSTI’s multiplex assay reader systemmore » (MARS), could provide advantages in terms of the number of simultaneously measured samples, portability, ruggedness, ease of use, accuracy, precision or cost as compared to the Luminexbased system developed at LLNL. The project underwent several no cost extensions however the overall goal of demonstrating the utility of this new system was achieved. As a result of the project a significant change to the type of bead PSTI used for the suspension system was implemented allowing better performance than the commercial Luminex system.« less

Water Treatment Using Advanced Ultraviolet Light Sources Final Report CRADA No. TC02089.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoppes, W.; Oster, S.

This was a collaborative effort between Lawrence Livermore National Security, LLC as manager and operator of Lawrence Livermore National Laboratory (LLNL) and Teknichal Services, LLC (TkS), to develop water treatment systems using advanced ultraviolet light sources. The Russian institutes involved with this project were The High Current Electronics Institute (HCEI) and Russian Institute of Technical Physics-Institute of Experimental Physics (VNIIEF). HCEI and VNIIEF developed and demonstrated the potential commercial viability of short-wavelength ultraviolet excimer lamps under a Thrust 1 Initiatives for Proliferation Prevention (IPP) Program. The goals of this collaboration were to demonstrate both the commercial viability of excilampbased watermore » disinfection and achieve further substantial operational improvement in the lamps themselves; particularly in the area of energy efficiency.« less

High-speed microprocessor characterization. Final report/project accomplishments summary, CRADA Number KCP-94-1004

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, L.W.

The objective of the project was to characterize and document the critical operating parameters of an 0.8-micron, 350-MHz, 32-bit microprocessor prototype. The roles of FM and T and the participant company were: FM and T -- evaluation performance of the prototype 32-bit microprocessor using the IDS5000 and Tektronix S3260 Integrated Circuit Test System; Corda -- design and build the prototype microprocessor. This project was terminated with nearly all of the planned activities unaddressed.

Rapid Assessment of Individual Soldier Operational Readiness Final Report CRADA No. TC02104.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Turteltaub, K.; Mapes, J.

This was a collaborative effort between Lawrence Livermore National Security (LLNS) (formerly The Regents of the University of California), Lawrence Livermore National Laboratory (LLNL) and Rules Based Medicine, Inc. {RBM), to identify markers in blood that would be candidates for determining the combat readiness of troops.

Automated feature extraction and classification from image sources

USGS Publications Warehouse

,

1995-01-01

The U.S. Department of the Interior, U.S. Geological Survey (USGS), and Unisys Corporation have completed a cooperative research and development agreement (CRADA) to explore automated feature extraction and classification from image sources. The CRADA helped the USGS define the spectral and spatial resolution characteristics of airborne and satellite imaging sensors necessary to meet base cartographic and land use and land cover feature classification requirements and help develop future automated geographic and cartographic data production capabilities. The USGS is seeking a new commercial partner to continue automated feature extraction and classification research and development.

Feeding ecology of the walleye (Percidae, Sander vitreus), a resurgent piscivore in Lake Huron (Laurentian Great Lakes) after shifts in the prey community

USGS Publications Warehouse

Pothoven, Steven A.; Madenjian, Charles P.; Höök, Tomas O.

2017-01-01

Recovering populations of piscivores can challenge understanding of ecosystem function due to impacts on prey and to potentially altered food webs supporting their production. Stocks of walleye (Percidae, Sander vitreus), an apex predator in the Laurentian Great Lakes, crashed in the mid‐1900s. Management efforts led to recovery by 2009, but recovery coincided with environmental and fish community changes that also had implications for the feeding ecology of walleye. To evaluate potential changes in feeding ecology for this apex predator, we assessed diets in the main basin of Lake Huron and in Saginaw Bay, a large embayment of Lake Huron, during 2009–2011. Walleye switched their diets differently in the main basin and Saginaw Bay, with non‐native round goby (Gobiidae, Neogobius melanostomus) and rainbow smelt (Osmeridae, Osmerus mordax) more prevalent in diets in the main basin, and invertebrates, yellow perch (Percidae,Perca flavescens) and gizzard shad (Clupeidae, Dorosoma cepedianum) more prevalent in diets in the bay. Feeding strategy plots indicated that there was a high degree of individual specialisation by walleye in the bay and the main basin. Bioenergetic simulations indicated that walleye in Saginaw Bay need to consume 10%–18% more food than a walleye that spends part or all of the year in the main basin, respectively, in order to achieve the same growth rate. The differences in diets between the bay and main basin highlight the flexibility of this apex predator in the face of environmental changes, but changes in diet can alter energy pathways supporting piscivore production.

Materials-Enabled High-Efficiency (MEHE) Heavy-Duty Diesel Engines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kass, M.; Veliz, M.

2011-09-30

The purpose of this Cooperative Research and Development Agreement (CRADA) between UTBattelle, Inc. and Caterpillar, Inc. was to improve diesel engine efficiency by incorporating advanced materials to enable higher combustion pressures and temperatures necessary for improved combustion. The project scope also included novel materials for use in advanced components and designs associated with waste-heat recovery and other concepts for improved thermal efficiency. Caterpillar initially provided ORNL with a 2004 Tier 2 C15 ACERT diesel engine (designed for on-highway use) and two 600 hp motoring dynamometers. The first year of the CRADA effort was focused on establishing a heavy-duty experimental enginemore » research cell. First year activities included procuring, installing and commissioning the cell infrastructure. Infrastructure components consisted of intake air handling system, water tower, exhaust handling system, and cell air conditioning. Other necessary infrastructure items included the fuel delivery system and bottled gas handling to support the analytical instrumentation. The second year of the CRADA focused on commissioning the dynamometer system to enable engine experimentation. In addition to the requirements associated with the dynamometer controller, the electrical system needed a power factor correction system to maintain continuity with the electrical grid. During the second year the engine was instrumented and baseline operated to confirm performance and commission the dynamometer. The engine performance was mapped and modeled according to requirements provided by Caterpillar. This activity was further supported by a Work-for-Others project from Caterpillar to evaluate a proprietary modeling system. A second Work-for-Others activity was performed to evaluate a novel turbocharger design. This project was highly successful and may lead to new turbocharger designs for Caterpillar heavy-duty diesel engines. During the third (and final) year of the

Electron Beam Cured Epoxy Resin Composites for High Temperature Applications

NASA Technical Reports Server (NTRS)

Janke, Christopher J.; Dorsey, George F.; Havens, Stephen J.; Lopata, Vincent J.; Meador, Michael A.

1997-01-01

Electron beam curing of Polymer Matrix Composites (PMC's) is a nonthermal, nonautoclave curing process that has been demonstrated to be a cost effective and advantageous alternative to conventional thermal curing. Advantages of electron beam curing include: reduced manufacturing costs; significantly reduced curing times; improvements in part quality and performance; reduced environmental and health concerns; and improvement in material handling. In 1994 a Cooperative Research and Development Agreement (CRADA), sponsored by the Department of Energy Defense Programs and 10 industrial partners, was established to advance the electron beam curing of PMC technology. Over the last several years a significant amount of effort within the CRADA has been devoted to the development and optimization of resin systems and PMCs that match the performance of thermal cured composites. This highly successful materials development effort has resulted in a board family of high performance, electron beam curable cationic epoxy resin systems possessing a wide range of excellent processing and property profiles. Hundreds of resin systems, both toughened and untoughened, offering unlimited formulation and processing flexibility have been developed and evaluated in the CRADA program.

33 CFR 117.647 - Saginaw River.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Lake State Railway Bridge, mile 3.10, and the Canadian National Railway Bridge, mile 4.94, both in Bay... if at least 12 hours advance notice is provided. (b) The draws of the Independence Bridge, mile 3.88, Liberty Street Bridge, mile 4.99, Veterans Memorial Bridge, mile 5.60, and Lafayette Street Bridge, mile 6...

33 CFR 117.647 - Saginaw River.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Lake State Railway Bridge, mile 3.10, and the Canadian National Railway Bridge, mile 4.94, both in Bay... if at least 12 hours advance notice is provided. (b) The draws of the Independence Bridge, mile 3.88, Liberty Street Bridge, mile 4.99, Veterans Memorial Bridge, mile 5.60, and Lafayette Street Bridge, mile 6...

33 CFR 117.647 - Saginaw River.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Lake State Railway Bridge, mile 3.10, and the Canadian National Railway Bridge, mile 4.94, both in Bay... if at least 12 hours advance notice is provided. (b) The draws of the Independence Bridge, mile 3.88, Liberty Street Bridge, mile 4.99, Veterans Memorial Bridge, mile 5.60, and Lafayette Street Bridge, mile 6...

33 CFR 117.647 - Saginaw River.

Code of Federal Regulations, 2011 CFR

2011-07-01

... as follows: (1) From 6:30 a.m. to 8:30 a.m. and 3:30 p.m. to 5:30 p.m. except Saturdays, Sundays, and... gross tons. (2) From 7:30 a.m. to 8:30 a.m. and 4:30 p.m. to 5:30 p.m. except on Sundays and Federal... bridge, mile 3.88, Liberty Street bridge, mile 4.99, Veterans Memorial bridge, mile 5.60, and Lafayette...

Evaluation of the Quantum Opportunities Program (QOP). Did the Program Work? A Report on the Post Secondary Outcomes and Cost-Effectiveness of the QOP Program (1989-1993).

ERIC Educational Resources Information Center

Hahn, Andrew; And Others

The Quantum Opportunities Project (QOP) was a multisite youth development demonstration project funded by the Ford Foundation in San Antonio (Texas), Philadelphia (Pennsylvania), Milwaukee (Wisconsin), Saginaw (Michigan), and Oklahoma City (Oklahoma). The programs, organized around educational activities, guaranteed up to 250 hours of education,…

Lack of interaction between glyphosate and fungicide treatments on Rhizoctonia crown and root rot in glyphosate-resistant sugarbeet

USDA-ARS?s Scientific Manuscript database

A field experiment was conducted in 2008 and 2009 in the Saginaw Valley region of Michigan to determine if there were potential interactions between applications of glyphosate and the fungicide azoxystrobin and to determine the effectiveness of foliar and in-furrow azoxystrobin applications when Rhi...

Community Defined Health: Thinking from the Inside Out.

ERIC Educational Resources Information Center

Blecke, Janalou; Hadden, Lisa

2000-01-01

Describes the "Community Defined Health" (trademark) process developed by the Center for Health Professions, Saginaw, Michigan, to capture caring, citizen engagement, and the quality of relationships and assure that these intangible assets become as valuable as institutionally defined health indicators in curricula for the health…

Cast CF8C-Plus Stainless Steel for Turbocharger Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maziasz, P.J.; Shyam, A.; Evans, N.D.

2010-06-30

The purpose of this Cooperative Research and Development Agreement (CRADA) project is to provide the critical test data needed to qualify CF8C-Plus cast stainless steel for commercial production and use for turbocharger housings with upgraded performance and durability relative to standard commercial cast irons or stainless steels. The turbocharger technologies include, but are not limited to, heavy-duty highway diesel engines, and passenger vehicle diesel and gasoline engines. This CRADA provides additional critical high-temperature mechanical properties testing and data analysis needed to quality the new CF8C-Plus steels for turbocharger housing applications.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davison, B. H.; Kuritz, T.

This CRADA was a collaborative effort between the Oak Ridge National Laboratory (ORNL) and Sass & Sass, Inc. It also had involvement with the University of Tennessee Knoxville (UTK) The CRADA focused on the development and commercialization in the U.S. of the substance developed in Russia with potential veterinary applications. The project addressed validation and further characterization of the lead substance necessary for its commercialization in the U.S. market as a veterinarian biologic and at the commercialization of the product for the Russian market, by the Russian group establishing of sustainability of the Russian research groups.

78 FR 72706 - Notice of Inventory Completion: Michigan State Police, Houghton Lake Post, Houghton Lake, MI

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-03

... remains were collected during road construction in Saginaw County by a private citizen and stored in a... City Road, Houghton Lake, MI 48629, telephone (989) 422-6923, email [email protected] Road, Houghton Lake, MI 48629, telephone (989) 422-6923, email [email protected] , by January 2...

Beta PIs from the USDA-ARS NPGS evaluated for resistance to Cercospora beticola, 2008

USDA-ARS?s Scientific Manuscript database

Sixty-two Plant Introductions (PIs) from the USDA-ARS National Plant Germplasm System were evaluated in an artificially produced epiphytotic for resistance to Cercospora beticola at the Saginaw Valley Bean and Beet Research Farm in MI. Internal controls included a susceptible check, USH20, and a res...

76 FR 19468 - Amended Certification Regarding Eligibility To Apply for Worker Adjustment Assistance

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-07

... Known As ATW Automation, Inc., Livonia Michigan TA-W-72,075A Assembly & Test Worldwide, Inc., Currently... Saginaw, Michigan locations of Assembly & Test Worldwide, Inc., are currently known as ATW Automation, Inc... Automation, Inc., Livonia, Michigan (TA-W-72,075); Assembly & Test Worldwide, Inc., currently known as ATW...

Rhizoctonia crown and root rot disease nursery

USDA-ARS?s Scientific Manuscript database

The BSDF cooperative CRR Eastern Evaluation Nursery Rhizoctonia crown and root rot Evaluation Nursery in 2016 was a randomized complete-block design with five replications in 15 feet long, one-row plots (20 in row spacing), at the Saginaw Valley Research and Education Center near Frankenmuth, MI. F...

33 CFR 151.66 - Operating requirements: Discharge of garbage in the Great Lakes and other navigable waters.

Code of Federal Regulations, 2012 CFR

2012-07-01

...; Thunder Bay National Marine Sanctuary means the site on or near Lake Huron designated by the National..., and potable water intakes; prohibited in the Thunder Bay National Marine Sanctuary. Iron ore Prohibited within 6 miles from shore and in Saginaw Bay; prohibited in the Thunder Bay National Marine...

33 CFR 151.66 - Operating requirements: Discharge of garbage in the Great Lakes and other navigable waters.

Code of Federal Regulations, 2011 CFR

2011-07-01

...; Thunder Bay National Marine Sanctuary means the site on or near Lake Huron designated by the National..., and potable water intakes; prohibited in the Thunder Bay National Marine Sanctuary. Iron ore Prohibited within 6 miles from shore and in Saginaw Bay; prohibited in the Thunder Bay National Marine...

76 FR 9599 - Notice of Inventory Completion: Denver Museum of Nature & Science, Denver, CO

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-18

... Sioux Tribe of the Rosebud Indian Reservation, South Dakota; Sac & Fox Nation of Missouri in Kansas and Nebraska; Sac & Fox Nation, Oklahoma; Sac & Fox Tribe of the Mississippi in Iowa; Saginaw Chippewa Indian... of Indians, Oklahoma; Rosebud Sioux Tribe of the Rosebud Indian Reservation, South Dakota; Sac & Fox...

Community Travel for Physically Impaired Students.

ERIC Educational Resources Information Center

Millet Learning Center, Saginaw, MI.

The community travel program for physically impaired children at the Millet Learning Center (Saginaw, Michigan) blends skills from two professions: orientation and mobility, and physical therapy. Program goals include enabling students to overcome travel fears, to learn travel skills, to learn to make adaptations necessary for successful travel,…

Public Key-Based Need-to-Know Authorization Engine Final Report CRADA No. TSB-1553-98

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mark, R.; Williams, R.

The goals of this project were to develop a public key-based authentication service plug-in based on LLNL's requirements, integrate the public key-based authentication with the Intra Verse authorization service adn the LLNL NTK server by developing a full-featured version of the prototyped Intra Verse need-to-know plug in; and to test the authorization and need-to-know plug-in in a secured extranet prototype among selected national Labs.

Development of Weldable Superplastic Forming Aluminum Alloy Sheet Final Report CRADA No. TC-1086-95

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lesuer, D.; Sun, T. C.

Numerous applications could exist for superplastic formable, weldable aluminum alloys in the automotive, aerospace, architectural, and construction industries. In this project, LLNL and Kaiser worked with the Institute for Metals Superplasticity Problems to develop and evaluate weldable superplastic alloys.

Fixed-Abrasive Grinding of Thin-Film Recording Heads Final Report CRADA No. TC-0498-93

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blaedel, K. L.; Newman, C.

The goals of this project were (1) to significantly reduce the cost of manufacturing thin-film recording heads for magnetic storage media and (2) to meet the stringent dimensional tolerances required for heads in the next generation high-density disc drives.

Fuel Testing for Sylvatex: Cooperative Research and Development Final Report, CRADA Number CRD-16-636

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burton, Jonathan L.

Sylvatex is a green nano-chemistry company that has developed a platform technology utilizing renewable, non-toxic inputs to create a stable nanoparticle that can be used in multiple applications. Their mission is to increase the use of renewables globally, to empower a cleaner and healthier future. The main application is a fuel technology product - MicroX - that utilizes proprietary knowledge to scale low-cost, cleaner-burning renewable diesel fuel and additives by using a co-location commercial model. The aspects of this project will include testing of two Sylvatex MicroX fuels on an engine dynamometer platform. Industry standard ultra-low sulfur diesel (ULSD) B3more » fuel and a ULSD B20 will both be used for comparison of the Sylvatex fuels (U.S. standard diesel fuel at the pump contains an average of approximately 3% biodiesel; this is why B3 would be used as a baseline comparison). Sylvatex is currently using a prototype formulation (MicroX 1) that applies a high cost surfactant. An experimental formulation (MicroX 2) that uses lower cost materials is under development. The MicroX 1 will be blended at a 10% level into the B3 ULSD fuel and the MicroX 2 will be blended at a 10% level into both the B3 and the B20 ULSD fuels for study on the engine dynamometer test platform. All fuel blends will be tested over the FTP transient engine test cycle and a steady state ramped modal engine test cycle. Each test cycle will be performed a minimum of 3 times for each fuel. Tailpipe and/or engine out gaseous exhaust emissions (CO2, CO, NOx, THC, O2,), engine out PM emissions, and brake-specific fuel consumption rates will be evaluated for all test cycles.« less

Microwave Sintering of Ceramic Materials for Industrial Application Final Report CRADA No. TC-1116-95

DOE Office of Scientific and Technical Information (OSTI.GOV)

Caplan, M.; Tandon, R.; Callis, R.

The goal of this project was to develop the commercial capability in the US to sinter alumina oxide ceramic parts for the semiconductor manufacturing equipment industry. We planned to use the millimeter microwave (30 GHz) sintering system first developed by IAP in Russia.

Development of Advanced Materials for Electro-Ceramic Application Final Report CRADA No. TC-1331-96

DOE Office of Scientific and Technical Information (OSTI.GOV)

Caplan, M.; Olstad, R.; McMillan, L.

The goal of this project was to further develop and characterize the electrochemical methods originating in Russia for producing ultra high purity organometallic compounds utilized as precursors in the production of high quality electro-ceramic materials. Symetrix planned to use electro-ceramic materials with high dielectric constant for microelectronic memory circuit applications. General Atomics planned to use the barium titanate type ceramics with low loss tangent for producing a high power ferroelectric tuner used to match radio frequency power into their Dill-D fusion machine. Phase I of the project was scheduled to have a large number of organometallic (alkoxides) chemical samples producedmore » using various methods. These would be analyzed by LLNL, Soliton and Symetrix independently to determine the level of chemical impurities thus verifying each other's analysis. The goal was to demonstrate a cost-effective production method, which could be implemented in a large commercial facility to produce high purity organometallic compounds. In addition, various compositions of barium-strontium-titanate ceramics were to be produced and analyzed in order to develop an electroceramic capacitor material having the desired characteristics with respect to dielectric constant, loss tangent, temperature characteristics and non-linear behavior under applied voltage. Upon optimizing the barium titanate material, 50 capacitor preforms would be produced from this material demonstrating the ability to produce, in quantity, the pills ultimately required for the ferroelectric tuner (approx 2000-3000 ceramic pills).« less

Shallow Water Imaging Sonar System for Environmental Surveying Final Report CRADA No. TC-1130-95

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ng, L. C.; Rosenbaum, H.

The scope of this research is to develop a shallow water sonar system designed to detect and map the location of objects such as hazardous wastes or discarded ordnance in coastal waters. The system will use high frequency wide-bandwidth imaging sonar, mounted on a moving platform towed behind a boat, to detect and identify objects on the sea bottom. Resolved images can be obtained even if the targets are buried in an overlayer of silt. Reference 1 ( also attached) summarized the statement of work and the scope of collaboration.

Tracking of Polycarbonate Films using Low-energy Ions Final Report CRADA No. TC-774-94

DOE Office of Scientific and Technical Information (OSTI.GOV)

Musket, R. G.

2018-01-24

Ion tracking is performed almost exclusively using ions with energies near or above the maximum in electronic stopping. For the present study, we have examined the results of etching ion tracks created by ions bombarding polycarbonate films with energies corresponding to stopping well below the maximum and just above the anticipated threshold for creating etchable latent tracks. Low-energy neon and argon ions with 18-60 keV /amu and fluences of about 10 8/cm 2 were used to examine the limits for producing etchable tracks in polycarbonate films. By concentrating on the early stages of etching (i.e., -20 nm < SEM holemore » diameter < -100 nm), we can directly relate the energy deposition calculated for the incident ion to the creation of etchable tracks. The experimental results will be discussed with regard to the energy losses of the ions in the polycarbonate films and to the formation of continuous latent tracks through the entire thickness the films. These results have significant implications with respect to the threshold for formation of etchable tracks and to the use of low-energy ions for lithographic applications.« less

LiverTox: Advanced QSAR and Toxicogeomic Software for Hepatotoxicity Prediction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lu, P-Y.; Yuracko, K.

2011-02-25

YAHSGS LLC and Oak Ridge National Laboratory (ORNL) established a CRADA in an attempt to develop a predictive system using a pre-existing ORNL computational neural network and wavelets format. This was in the interest of addressing national needs for toxicity prediction system to help overcome the significant drain of resources (money and time) being directed toward developing chemical agents for commerce. The research project has been supported through an STTR mechanism and funded by the National Institute of Environmental Health Sciences beginning Phase I in 2004 (CRADA No. ORNL-04-0688) and extending Phase II through 2007 (ORNL NFE-06-00020). To attempt themore » research objectives and aims outlined under this CRADA, state-of-the-art computational neural network and wavelet methods were used in an effort to design a predictive toxicity system that used two independent areas on which to base the system’s predictions. These two areas were quantitative structure-activity relationships and gene-expression data obtained from microarrays. A third area, using the new Massively Parallel Signature Sequencing (MPSS) technology to assess gene expression, also was attempted but had to be dropped because the company holding the rights to this promising MPSS technology went out of business. A research-scale predictive toxicity database system called Multi-Intelligent System for Toxicogenomic Applications (MISTA) was developed and its feasibility for use as a predictor of toxicological activity was tested. The fundamental focus of the CRADA was an attempt and effort to operate the MISTA database using the ORNL neural network. This effort indicated the potential that such a fully developed system might be used to assist in predicting such biological endpoints as hepatotoxcity and neurotoxicity. The MISTA/LiverTox approach if eventually fully developed might also be useful for automatic processing of microarray data to predict modes of action. A technical paper describing

Higher Education In Michigan: Overcoming Challenges to Expand Access

ERIC Educational Resources Information Center

Cunningham, Alisa F.; Erisman, Wendy; Looney, Shannon E.

2008-01-01

This report examines access to higher education in underserved regions of Michigan. This study focuses on specific concerns about postsecondary education access in three geographically diverse areas of the state: suburban Macomb County; the city of Saginaw; and six rural counties in the northeastern Lower Peninsula. The report provides a summary…

School Safety Project: Product Evaluation, 1990-1991.

ERIC Educational Resources Information Center

Saginaw Public Schools, MI. Dept. of Evaluation Services.

A districtwide school safety project implemented in Saginaw, Michigan, in 1990-91, the third year of its operation, is evaluated in this report. The project is evaluated on the basis of the following objectives: employment and training of home-school liaison officers; establishment of an advisory council; development and implementation of…

DOE Office of Scientific and Technical Information (OSTI.GOV)

Balachandran, U.

The purpose of this CRADA is to develop a fabrication process to reduce the manufacturing cost for a very compact, high temperature, film-on-foil high energy-density PLZT (Pb-La-Zr- Ti-O) capacitor. Motivation for this CRADA is derived from the DOE’s Office of Vehicle Technologies (OVT) program, which seeks to advance technologies to improve vehicle fuel efficiency in the mid-term and facilitate the transition to electric drive vehicles over the longterm. The objective of Argonne’s work is to develop and characterize high-performance capacitors on base-metal foils. The PLZT film-on-foil prepared using a spin-coating technique

Wireless Sensor for Measuring Pump Efficiency: Small Business Voucher Project with KCF Technologies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fugate, David L.; Liu, Xiaobing; Gehl, Anthony C.

This document is to fulfill the final report requirements for the Small Business Voucher (SBV) CRADA project with ORNL and KCF Technologies (CRADA/NFE-16-06133). Pumping systems account for nearly 20% of the world’s electrical energy demand and range from 25-50% of the energy usage in many industrial and building power plants. The energy cost is the largest element in the total cost of owning a pump (~40%). In response to a recent DOE mandate for improved pump efficiency pump manufacturers are preparing for the changes that the impending regulations will bring, including design improvements. This mandate also establishes a need formore » new low cost pump efficiency measurement systems. The standard industry definition of pump efficiency is the mechanical water horsepower delivered divided by the electrical horsepower input to the motor. KCF Technologies has developed a new sensor measurement technique to estimate fluid pump efficiency using a thermodynamic approach. KCF Technologies applied for a SBV grant with ORNL as the research partner. KCF needed a research partner with the proper facilities to demonstrate the efficacy of its wireless sensor unit for measuring pump efficiency. The ORNL Building Technologies Research and Integration Center (BTRIC) test resources were used to test and demonstrate the successful measurement of pump efficiency with the KCF sensor technology. KCF is now working on next steps to commercialize this sensing technology.« less

District-Wide Comprehensive Needs Assessment Study. Summary of System Totals, Part I, 1984-85.

ERIC Educational Resources Information Center

Saginaw Public Schools, MI. Dept. of Evaluation Services.

System totals from the needs assessment study conducted for planning purposes by the Saginaw, Michigan, Public Schools in the spring of 1985 are summarized. The data are based on 2,100 questionnaire responses from parents, community members, students, administrators, and teachers. Results of the School-Community Survey and the Priority Needs Index…

75 FR 28648 - Notice of Inventory Completion: Peabody Museum of Archaeology and Ethnology, Harvard University...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-21

... Douglass Houghton, the first Geologist for the State of Michigan, indicates that there was a village near the mouth of the Tawas River in 1838. He describes the village as that of Outawanse. Consultation with... across the water from Tawas Point, where these remains were recovered. Given the presence of the Saginaw...

Compensatory Education Product Evaluation: Elementary and Secondary Programs 1991-1992.

ERIC Educational Resources Information Center

Saginaw Public Schools, MI. Dept. of Evaluation Services.

An evaluation was done of compensatory educational programs in reading and mathematics in the Saginaw (Michigan) School District. The elementary Compensatory Education (CE) program is both a push-in format (grades 1 and 2) and a pull-out format (periodically taking students out of regular classrooms) that serves 2,045 students in grades 1 through…

Balsa Tower Walls Brave "Big Buster"

ERIC Educational Resources Information Center

Granlund, George

2008-01-01

Like many technology teachers, the author, a technology education teacher at Arthur Hill High School in Saginaw, Michigan, tries to stretch his budget by "milking" each student activity for maximum benefit. In the technology department, they use balsa wood towers to teach the basics of structural engineering. To get the most from their materials,…

Supporting the Development of Intrinsic Motivation in the Middle School Classroom.

ERIC Educational Resources Information Center

Oginsky, Terri

This study took place in a sixth grade math class at Webber Middle School in Saginaw, Michigan. A literature review indicated that a classroom that students perceive as safe, supportive of their autonomy, and of their learning increases intrinsic motivation. With this in mind, the author created a study, which would look for connections between…

Potential effects of climate change on ground water in Lansing, Michigan

USGS Publications Warehouse

Croley, T.E.; Luukkonen, C.L.

2003-01-01

Computer simulations involving general circulation models, a hydrologic modeling system, and a ground water flow model indicate potential impacts of selected climate change projections on ground water levels in the Lansing, Michigan, area. General circulation models developed by the Canadian Climate Centre and the Hadley Centre generated meteorology estimates for 1961 through 1990 (as a reference condition) and for the 20 years centered on 2030 (as a changed climate condition). Using these meteorology estimates, the Great Lakes Environmental Research Laboratory's hydrologic modeling system produced corresponding period streamflow simulations. Ground water recharge was estimated from the streamflow simulations and from variables derived from the general circulation models. The U.S. Geological Survey developed a numerical ground water flow model of the Saginaw and glacial aquifers in the Tri-County region surrounding Lansing, Michigan. Model simulations, using the ground water recharge estimates, indicate changes in ground water levels. Within the Lansing area, simulated ground water levels in the Saginaw aquifer declined under the Canadian predictions and increased under the Hadley.

U.S. Geological Survey and Microsoft Cooperative Research and Development Agreement: Geospatial Data Browsing and Retrieval Site on the World Wide Web

USGS Publications Warehouse

,

1999-01-01

In May 1997, the U.S. Geological Survey (USGS) and the Microsoft Corporation of Redmond, Wash., entered into a cooperative research and development agreement (CRADA) to make vast amounts of geospatial data available to the general public through the Internet. The CRADA is a 36-month joint effort to develop a general, public-oriented browsing and retrieval site for geospatial data on the Internet. Specifically, Microsoft plans to (1) modify a large volume of USGS geospatial data so the images can be displayed quickly and easily over the Internet, (2) implement an easy-to-use interface for low-speed connections, and (3) develop an Internet Web site capable of servicing millions of users per day.

U.S. Geological Survey and Microsoft Cooperative Research and Development Agreement: Geospatial Data Browsing and Retrieval Site on the World Wide Web

USGS Publications Warehouse

,

1998-01-01

In May 1997, the U.S. Geological Survey (USGS) and the Microsoft Corporation of Redmond, Wash., entered into a cooperative research and development agreement (CRADA) to make vast amounts of geospatial data available to the general public through the Internet. The CRADA is a 36-month joint effort to develop a general, public-oriented browsing and retrieval site for geospatial data on the Internet. Specifically, Microsoft plans to (1) modify a large volume of USGS geospatial data so the images can be displayed quickly and easily over the Internet, (2) implement an easy-to-use interface for low-speed connections, and (3) develop an Internet Web site capable of servicing millions of users per day.

US Army Order of Battle 1919-1941. Volume 2. The Arms: Calvary, Field Artillery, and Coast Artillery, 1919-41

DTIC Science & Technology

2010-01-01

Artillery Regiment (75-mm G-P) (GHQR) Organized Reserve Michigan HQ— Alpena , MI, 1921–25; Flint, MI, 1925–29; Inactive, 1929–41 Constituted in the O.R. on... Alpena , MI. Subordinate battalion HQ concurrently organized as follows: 1st Bn. at Saginaw, MI,and 2d Bn. at Owosso, MI. Regimental HQ relocated on 2

77 FR 12594 - Agency Forms Undergoing Paperwork Reduction Act Review

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-01

... study. In Michigan, people fishing along the shores of the Detroit River and Saginaw River and Bay will be asked a few questions to see if they are willing to take part in the study. In Minnesota, American Indians will be randomly chosen from a list of people who get local tribal health clinic and social...

33 CFR 151.66 - Operating requirements: Discharge of garbage in the Great Lakes and other navigable waters of the...

Code of Federal Regulations, 2013 CFR

2013-07-01

... from the center of Superior Shoal, at 48°03.2′ N 87°06.3′ W; Thunder Bay National Marine Sanctuary... Thunder Bay National Marine Sanctuary. Iron ore Prohibited within 6 miles from shore and in Saginaw Bay; prohibited in the Thunder Bay National Marine Sanctuary; prohibited for vessels up bound along the Michigan...

33 CFR 151.66 - Operating requirements: Discharge of garbage in the Great Lakes and other navigable waters.

Code of Federal Regulations, 2014 CFR

2014-07-01

... of Superior Shoal, at 48°03.2′ N 087°06.3′ W. Thunder Bay National Marine Sanctuary means the site on... stone Prohibited within 3 miles from shore; prohibited in the Thunder Bay National Marine Sanctuary. Iron ore Prohibited within 6 miles from shore and in Saginaw Bay; prohibited in the Thunder Bay...

Development of a Dynamic Time Sharing Scheduled Environment Final Report CRADA No. TC-824-94E

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jette, M.; Caliga, D.

Massively parallel computers, such as the Cray T3D, have historically supported resource sharing solely with space sharing. In that method, multiple problems are solved by executing them on distinct processors. This project developed a dynamic time- and space-sharing scheduler to achieve greater interactivity and throughput than could be achieved with space-sharing alone. CRI and LLNL worked together on the design, testing, and review aspects of this project. There were separate software deliverables. CFU implemented a general purpose scheduling system as per the design specifications. LLNL ported the local gang scheduler software to the LLNL Cray T3D. In this approach, processorsmore » are allocated simultaneously to aU components of a parallel program (in a “gang”). Program execution is preempted as needed to provide for interactivity. Programs are also reIocated to different processors as needed to efficiently pack the computer’s torus of processors. In phase one, CRI developed an interface specification after discussions with LLNL for systemlevel software supporting a time- and space-sharing environment on the LLNL T3D. The two parties also discussed interface specifications for external control tools (such as scheduling policy tools, system administration tools) and applications programs. CRI assumed responsibility for the writing and implementation of all the necessary system software in this phase. In phase two, CRI implemented job-rolling on the Cray T3D, a mechanism for preempting a program, saving its state to disk, and later restoring its state to memory for continued execution. LLNL ported its gang scheduler to the LLNL T3D utilizing the CRI interface implemented in phases one and two. During phase three, the functionality and effectiveness of the LLNL gang scheduler was assessed to provide input to CRI time- and space-sharing, efforts. CRI will utilize this information in the development of general schedulers suitable for other sites and future architectures.« less

Rapid Tooling for Functional Prototype of Metal Mold Processes Final Report CRADA No. TC-1032-98

DOE Office of Scientific and Technical Information (OSTI.GOV)

Heestand, G.; Jaskolski, T.

Production inserts for die-casting were generally fabricated from materials with sufficient strength and· good wear properties at casting temperatures for long life. Frequently tool steels were used and machining was done with a combination of. conventional and Electric Discharge Machining (EDM) with some handwork, an expensive and time consuming process, partilly for prototype work. We proposed electron beam physical vapor deposition (EBPVD) as a process for rapid fabrication of dies. Metals, ranging from low melting point to refractory metals (Ta, Mo, etc.), would be evaporated and deposited at high rates (-2mm/hr.). Alloys could be easily evaporated and deposited if theirmore » constituent vapor pressures were similar and with more difficulty if they were not. Of course, layering of different materials was possible if required for a specific application. For example, a hard surface layer followed by a tough steel and backed by a high thermal conductivity (possibly cooled) copper layer could be fabricated. Electron-beam deposits exhibited 100% density and lull strength when deposited at a substrate (mandrel) temperature that was a substantial fraction of the deposited material's melting point. There were several materials that could have the required high temperature properties and ease of fabrication required for such a mandrel. We had successfully used graphite, machined from free formed objects with a replicator, to produce aluminum-bronze test molds. There were several parting layer materials of interest, but the ideal material depended upon the specific application.« less

Accelerator-Detector Complex for Photonuclear Detection of Hidden Explosives Final Report CRADA No. TC2065.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lowdermilk, W. H.; Brothers, L. J.

This was a collaborative effort by Lawrence Livermore National Security (formerly the University of California)/Lawrence Livermore National Laboratory (LLNL), Valley Forge Composite Technologies, Inc., and the following Russian Institutes: P. N. Lebedev Physical Institute (LPI), Innovative Technologies Center.(AUO CIT), Central Design Bureau-Almas (CDB Almaz), Moscow Instrument Automation Research Institute, and Institute for High Energy Physics (IBEP) to develop equipment and procedures for detecting explosive materials concealed in airline checked baggage and cargo.

Flow Visualization Studies in the Novacor Left Ventricular Assist System CRADA PC91-002, Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Borovetz, H.S.; Shaffer, F.; Schaub, R.

This paper discusses a series of experiments to visualize and measure flow fields in the Novacor left ventricular assist system (LVAS). The experiments utilize a multiple exposure, optical imaging technique called fluorescent image tracking velocimetry (FITV) to hack the motion of small, neutrally-buoyant particles in a flowing fluid.

Phase II: Automated System for Aneuploidy Detection in Sperm Final Report CRADA No. TC-1554-98

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wyrobek, W. J.; Dunlay, R. T.

This was a collaborative effort between the University of California, Lawrence Livermore National Laboratory (LLNL) and Cellomics, Inc. (formerly BioDx and Biological Detection, Inc.) to develop an automated system for detecting human sperm aneuploidy. Aneuploidy (an abnormal number of chromosomes) is one of the major categories of chromosomally abnormal sperm, which results in chromosomally defective pregnancies and babies. An automated system would be used for testing the effects of toxic agents and for other research and clinical applications. This collaborated effort was funded by a National Institutes of Environmental Health Services, Phase II, Small Business Innovation Research Program (SBIR) grantmore » to Cellornics (Contract No. N44-ES-82004).« less

Hazardous and Medical Waste Destruction Using the AC Plasmatron Final Report CRADA No. TC-1560-98

DOE Office of Scientific and Technical Information (OSTI.GOV)

Caplan, M.; Bucher, K.; Tulupov, A.

The goal of this project was to develop a prototype medical waste destruction facility based on the AC plasma torch capable of processing 150 kg of waste per hour while satisfying US EPA emission standards. The project was to provide the first opportunity for a joint U.S.-Russian project using an AC Plasma Torch in a hazardous waste destruction system to be assembled and operated in the U.S. thus promoting the commercialization in the U.S. of this joint U.S.-Russian developed technology. This project was a collaboration between the Russian Institute Soliton- NTT, the U.S industrial partner Scientific Utilization Inc. (SUI) andmore » Lawrence Livermore National Laboratory ( LLNL). The project was funded by DOE for a total of $1.2 million with $600K for allocated for Phase I and $600K for Phase II. The Russian team received about $800K over the two (2) year period while LLNL received $400K. SUI was to provide in kind matching funds totaling $1.2 million.« less

Evaluation of SAGE Electrochromic Devices: Cooperative Research and Development Final Report, CRADA Number CRD-15-579

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tenent, Robert C.

2017-12-06

NREL will conduct durability testing of Sage Electrochromics dynamic windows products using American Society for Testing and Materials (ASTM) standard methods and drive parameters as defined by Sage. Window units will be tested and standard analysis performed. Data will be summarized and reported back to Sage at the end of the testing period.

Biodiesel Performance with Modern Engines. Cooperative Research and Development Final Report, CRADA Number CRD-05-153

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCormick, Robert

NREL and the National Biodiesel Board (NBB) will work cooperatively to assess the effects of biodiesel blends on the performance of modern diesel engines and emissions control systems meeting increasingly strict emissions standards. This work will include research to understand the impact of biodiesel blends on the operation and durability of particle filters and NOx control sorbents/catalysts, to quantify the effect on emission control systems performance, and to understand effects on engine component durability. Work to assess the impact of biodiesel blends on real world fleet operations will be performed. Also, research to develop appropriate ASTM standards for biodiesel qualitymore » and stability will be conducted. The cooperative project will involve engine testing and fleet evaluation studies at NREL using biodiesel from a variety of sources. In addition, NREL will work with NBB to set up an Industrial Steering Committee to design the scope for the various projects and to provide technical oversight to these projects. NREL and NBB will cooperatively communicate the study results to as broad an audience as possible.« less

Renewable Energy Institute International (REII): Cooperative Research and Development Final Report, CRADA Number CRD-10-387

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carpenter, D.

2014-11-01

NREL will provide the Renewable Energy Institute with detailed on-site biomass gasifier syngas monitoring, using the NREL transportable Molecular Beam Mass Spectrometer. This information will be used to optimize the parameters of the gasifier operation, insuring the quality of the syngas made in the Red Lion Bioenergy gasifier and its compatibility with catalytic conversion to fuels.

Manufacturing Steps for Commercial Production of Nano-Structure Capacitors Final Report CRADA No. TC02159.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barbee, T. W.; Schena, D.

This was a collaborative effort between Lawrence Livermore National Security, LLC as manager and operator of Lawrence Livermore National Laboratory (LLNL) and TroyCap LLC, to develop manufacturing steps for commercial production of nano-structure capacitors. The technical objective of this project was to demonstrate high deposition rates of selected dielectric materials which are 2 to 5 times larger than typical using current technology.

A Portable Cell Maintenance System for Rapid Toxicity Monitoring Final Report CRADA No. TC-02081-04

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kane, S.; Zhou, P.

The Phase I STTR research project was targeted at meeting the objectives and requirements stated in STTR solicitation A04-T028 for a Portable Cell Maintenance System for Rapid Toxicity Monitoring. In accordance with the requirements for STTR programs, collaboration was formed between a small business, Kionix, Inc., and The Regents of the University of California, Lawrence Livermore National Laboratory (LLNL). The collaboration included CytoDiscovery, Inc. (CDI) which, in collaboration with Kionix, provided access to membrane chip technology and provided program support and coordination. The objective of the overall program (excerpted from the original solicitation) was: “To develop a small, portable cellmore » maintenance system for the transport, storage, and monitoring of viable vertebrate cells and tissues.” The goal of the Phase I project was to demonstrate the feasibility of achieving the program objectives utilizing a system comprised of a small-size, microfluidic chip-based cell maintenance cartridge (CMC) and a portable cell maintenance system (CMS) capable of housing a minimum of four CMCs. The system was designed to be capable of optimally maintaining multiple vertebrate cell types while supporting a wide variety of cellular assays.« less

Compiling for Application Specific Computational Acceleration in Reconfigurable Architectures Final Report CRADA No. TSB-2033-01

DOE Office of Scientific and Technical Information (OSTI.GOV)

De Supinski, B.; Caliga, D.

2017-09-28

The primary objective of this project was to develop memory optimization technology to efficiently deliver data to, and distribute data within, the SRC-6's Field Programmable Gate Array- ("FPGA") based Multi-Adaptive Processors (MAPs). The hardware/software approach was to explore efficient MAP configurations and generate the compiler technology to exploit those configurations. This memory accessing technology represents an important step towards making reconfigurable symmetric multi-processor (SMP) architectures that will be a costeffective solution for large-scale scientific computing.

Process Parameter Evaluation and Optimization for Advanced Material Development Final Report CRADA No. TC-1234-96

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hrubesh, L.; McGann, T. W.

This project was established as a three-year collaboration to produce and characterize · silica aerogels prepared by a Rapid Supercritical Extraction (RSCE) process to meet . BNA, Inc. application requirements. The objectives of this project were to study the parameters necessary to produce optimized aerogel parts with narrowly specified properties and establish the range and limits of the process for producing such aerogels. The project also included development of new aerogel materials useful for high temperature applications. The results of the project were expected to set the conditions necessary to produce quantities of aerogels having particular specifications such as size,more » shape, density, and mechanical strength. BNA, Inc. terminated the project on April 7, 1999, 10-months prior to the anticipated completion date, due to termination of corporate funding for the project. The technical accomplishments achieved are outlined in Paragraph C below.« less

Phase II, Compact AMS System for Biological Tracer Detection Final Report CRADA No. TSV-1533-96

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, T. A.; Hamm, R. W.

2017-11-01

The objective of this collaboration between LLNL and AccSys Technology, Inc. of Pleasanton, California was to build and demonstrate a low cost, compact tritium (3H) Accelerator Mass Spectrometer (AMS) system matched to the requirements of biomedical research.

CRADA Final Report For CRADA NO. CR-12-006 [Operation and Testing of an SO 2-depolarized Electrolyzer (SDE) for the Purpose of Hydrogen and Sulfuric Acid Production

DOE Office of Scientific and Technical Information (OSTI.GOV)

Summers, W. A.; Colon-Mercado, H. R.; Steimke, J. L.

2014-02-24

Over the past several years, Savannah River National Laboratory (SRNL) has led a team of collaborators under the Department of Energy’s (DOE) nuclear hydrogen production program to develop the Hybrid Sulfur (HyS) Process. HyS is a 2-step water-splitting process consisting of high temperature decomposition of sulfuric acid to generate SO 2, followed by the electrolysis of aqueous SO 2 to generate hydrogen and sulfuric acid. The latter is fed back into the high temperature reactor. SRNL designed and built an SO 2-depolarized electrolyzer (SDE) and a test facility. Over 40 SDE’s were tested using different catalysts, membranes and other components.more » SRNL demonstrated that an SDE could be operated continuously for approximately 200 hours under certain conditions without buildup of sulfur at the SDE’s cathode, thus solving a key technical problem with SDE technology. Air Products and Chemicals, Inc. (APCI) is a major supplier of hydrogen production systems, and they have proprietary technology that could benefit from the SDE developed by SRNS, or some improved version thereof. However, to demonstrate that SRNL’s SDE is a truly viable approach to the electrolyzer design, continuous operation for far greater periods of time than 200 hours must be demonstrated, and the electrolyzer must be scaled up to greater hydrogen production capacities. SRNL and Air Products entered into a Cooperative Research and Development Agreement with the objective of demonstrating the effectiveness of the SDE for hydrogen and sulfuric acid production and to demonstrate long-term continuous operation so as to dramatically increase the confidence in the SDE design for commercial operation. SRNL prepared a detailed technical report documenting previous SDE development, including the current SDE design and operating conditions that led to the 200-hour sulfurfree testing. SRNL refurbished its single cell SDE test facility and qualified the equipment for continuous operation. A new membrane electrode assembly (MEA) was fabricated and installed in the single cell electrolyzer (60 cm 2 active cell area). Shakedown testing was conducted, and several modifications were made to the test facility equipment. Seven different MEAs were used during testing. Beginning on May 20, 2013, SRNL was able to test the SDE continuously for 1200 hours, including 1000 hours under power to generate hydrogen at an average rate of 10.8 liters per hour. The SDE was not removed or repaired during the 50-day test and was successfully restarted after each shutdown. The test was intentionally stopped after 1200 hours (1000 hours of hydrogen production) due to funding constraints. Post-test examination of the MEA using Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Microanalysis (EDAX) showed no elemental sulfur deposits or sulfur layer inside the cell, thus successfully achieving the test goals. The results demonstrated that the SDE could be operated for extended periods without major performance degradation or the buildup of sulfur inside the MEA. Air Products conducted an assessment of the economic viability of the SDE based on the “as tested” design. The results indicated that the SDE faces significant economic obstacles in its current state. Further development and scale-up are necessary before the SDE is ready for commercialization.« less

Image analysis of hardened concrete : performance enhancement of the Automated Concrete Evaluation System (ACES).

DOT National Transportation Integrated Search

2006-01-01

Since 2001, the Missouri Department of Transportation and National Nuclear Security Administrations Kansas City Plant, : operated by Honeywell Federal Manufacturing & Technologies, have collaborated on three CRADAs (Cooperative : Research and D...

10 CFR 950.37 - Final agreement or final decision.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 4 2011-01-01 2011-01-01 false Final agreement or final decision. 950.37 Section 950.37 Energy DEPARTMENT OF ENERGY STANDBY SUPPORT FOR CERTAIN NUCLEAR PLANT DELAYS Dispute Resolution Process § 950.37 Final agreement or final decision. (a) If the parties reach a Final Agreement on a contract...

Halaven® - eribulin mesylate (analog of halichondrin B) | NCI Technology Transfer Center | TTC

Cancer.gov

Under a CRADA with NCI, Eisai Co. provided eribulin for NCI's preclinical development activities and to support NCI's Phase I clinical trials. Eisai ultimately took the product, Halaven®, to licensure.

48 CFR 970.5227-2 - Rights in data-technology transfer.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Research and Development Agreement (CRADA) information in accordance with Technology Transfer actions under... descriptive of the data and is suitable for dissemination purposes, (B) The program under which it was funded...

48 CFR 970.5227-2 - Rights in data-technology transfer.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Research and Development Agreement (CRADA) information in accordance with Technology Transfer actions under... descriptive of the data and is suitable for dissemination purposes, (B) The program under which it was funded...

48 CFR 970.5227-2 - Rights in data-technology transfer.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Research and Development Agreement (CRADA) information in accordance with Technology Transfer actions under... descriptive of the data and is suitable for dissemination purposes, (B) The program under which it was funded...

48 CFR 970.5227-2 - Rights in data-technology transfer.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Research and Development Agreement (CRADA) information in accordance with Technology Transfer actions under... descriptive of the data and is suitable for dissemination purposes, (B) The program under which it was funded...

U.S. Civil Airmen Statistics Calendar Year 1992

DTIC Science & Technology

1993-06-01

580 99 0 315 103 57 6 66 PRESQUE ISLE ............... 16 4 0 8 2 2 0 1 ROSCOMMON ............ 62 12 0 36 12 1 1 3 SAGINAW...1,595 New York ..... ............................... 21,917 4,573 9,637 4,277 2,427 1,003 2,423 Pennsylvania ...1,348 497 523 181 73 74 123 Pennsylvania .............................................. 1,324 486 553

A Rain Garden for Our School: Becoming Environmental Stewards

ERIC Educational Resources Information Center

McFadyen, Joy

2012-01-01

In this article, the author talks about a rain garden project at Hampton Elementary School in Bay City, Michigan. The goal of the project was to slow and filter silt-laden runoff (from parking lots, sidewalks, and playground) on its path to Saginaw Bay in Lake Huron. In addition, doing so, the rain gardens would demonstrate to the township, city,…

Can't Blame Anyone Else for My Problems

ERIC Educational Resources Information Center

Pego, David

2003-01-01

The author is a full-blood Saginaw Chippewa Indian tribal member who is trying to enter the world of academia late in life. He relates he has never been subjected to unfair treatment or criticism from others because of the color of his skin. He has taught part-time at the University of Texas College of Communications and last year at South Dakota…

NREL Helps Industry Partner Commercialize Promising Technology For Forest

Science.gov Websites

development agreement (CRADA) with Minerals Technologies, Inc. of Bethlehem, Penn. to conduct research to -shared research agreement is designed to provide Minerals Technologies, Inc. access to NREL's research

Cost Effective Bioethanol via Acid Pretreatment of Corn Stover, Saccharification, and Conversion via a Novel Fermentation Organism: Cooperative Research and Development Final Report, CRADA Number: CRD-12-485

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dowe, N.

2014-05-01

This research program will convert acid pretreated corn stover to sugars at the National Renewable Energy Laboratory (NREL) and then transfer these sugars to Honda R&D and its partner the Green Earth Institute (GEI) for conversion to ethanol via a novel fermentation organism. In phase one, NREL will adapt its pretreatment and saccharification process to the unique attributes of this organism, and Honda R&D/GEI will increase the sugar conversion rate as well as the yield and titer of the resulting ethanol. In later phases, NREL, Honda R&D, and GEI will work together at NREL to optimize and scale-up to pilot-scalemore » the Honda R&D/GEI bioethanol production process. The final stage will be to undertake a pilot-scale test at NREL of the optimized bioethanol conversion process.« less

Predictive Engineering Tools for Injection-Molded Long-Carbon-Fiber Thermoplastic Composites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nguyen, Ba Nghiep; Simmons, Kevin L.

This quarterly report summarizes the status for the project planning to complete all the legal and contract documents required for establishing the subcontracts needed and a Cooperative Research and Development Agreement (CRADA) with Autodesk, Inc., Toyota Motor Engineering and Manufacturing North America (Toyota), and Magna Exterior and Interiors Corporation (Magna). During the second quarter (1/1/2013 to 3/31/2013), all the technical and legal documents for the subcontracts to Purdue University, University of Illinois, and PlastiComp, Inc. were completed. The revised CRADA documents were sent to DOE, Autodesk, Toyota, and Magna for technical and legal reviews. PNNL Legal Services contacted project partners’more » Legal counterparts for completing legal documents for the project. A non-disclosure agreement was revised and sent to all the parties for reviews.« less

Predictive Engineering Tools for Injection-Molded Long-Carbon-Fiber Thermoplastic Composites - Quarterly Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nguyen, Ba Nghiep; Simmons, Kevin L.

This quarterly report summarizes the status for the project planning to initiate all the legal and contract documents required for establishing the subcontracts needed and a Cooperative Research and Development Agreement (CRADA) with Autodesk, Inc., Toyota Motor Engineering and Manufacturing North America (Toyota), and Magna Exterior and Interiors Corporation (Magna). During the first quarter (10/1/2012 to 12/31/2012), the statements of work (SOW) for the subcontracts to Purdue University, University of Illinois, and PlastiComp, Inc. were completed. A draft of the CRADA SOW was sent to Autodesk, Toyota, and Magna for technical and legal reviews. PNNL Legal Services contacted project partners’more » Legal counterparts for preparing legal documents for the project. A non-disclosure agreement was drafted and sent to all the parties for reviews.« less

Dinutuximab (Unituxin™) | NCI Technology Transfer Center | TTC

Cancer.gov

In 2010, NCI entered into a Cooperative Research and Development Agreement (CRADA) with United Therapeutics Corp., under which the company assumed responsibility for manufacturing dinutuximab and moving it through the steps required for regulatory approval.

St. Lawrence Seaway N.Y. Feasibility Study for Additional Locks and Other Navigation Improvements: Plan of Study. Revision.

DTIC Science & Technology

1979-11-01

Ashland, WI Lake Huron Lake Michigan Ontonagon, MI Presque Isle, MI : Alpena , MI Oak Creek, WI Marquette, MI Cheboygan, MI Buffington, IN Keweenaw Waterway...State of Michigan include Calcite, Stoneport, Alpena , Alabasier, Bay City, Saginaw, and Port Huron. Other large harbors on Lake Michigan are Port...Joseph Alpena : Auglaize Tompkins Steuben : Arenac Crawford Wayne Bay Cayuga Wyoming Cheboygan Defiance Yates Clare Erie Crawford : Fulton Source

78 FR 44592 - Final General Management Plan, Final Wilderness Study, and Final Environmental Impact Statement...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-24

... General Management Plan and Wilderness Study (Final EIS/GMP/WS) for Fort Pulaski National Monument... national monument, the Final EIS/GMP/WS will guide the management of the national monument over the next 20... publication of the Environmental Protection Agency's Notice of Availability of the Final EIS/GMP/WS in the...

GREEN REACTION CHEMISTRIES PERFORMED IN THE SPINNING TUBE-IN-TUBE (STT) REACTOR

EPA Science Inventory

The U. S. Environmental Protection Agency (USEPA) and Kreido Laboratories have established a Cooperative Research and Development Agreement (CRADA) collaboration, to develop and commercialize green and sustainable chemistries in the area of industrial chemical synthesis. Utilizi...

PROCESS INTENSIFIED GREEN REACTION CHEMISTRIES PERFORMED IN THE SPINNING TUBE-IN-TUBE (STT®) REACTOR

EPA Science Inventory

The U. S. Environmental Protection Agency (USEPA) and Kreido Laboratories have established a Cooperative Research and Development Agreement (CRADA) collaboration, to develop and commercialize green and sustainable chemistries in the area of industrial chemical synthesis. Utilizi...

GREEN REACTION CHEMISTRIES PERFORMED IN THE SST REACTOR

EPA Science Inventory

The U. S. Environmental Protection Agency (USEPA) and Kreido Laboratories have established a Cooperative Research and Development Agreement (CRADA) collaboration, to develop and commercialize green and sustainable chemistries in the area of industrial chemical synthesis. Uti...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Edwin S.

Under the CRADA, NREL will provide assistance to NRGsim to debug and convert the EnergyPlus Hysteresis Phase Change Material ('PCM') model to C++ for adoption into the main code package of the EnergyPlus simulation engine.

Hydrogen Compressor Reliability Investigation and Improvement. Cooperative Research and Development Final Report, CRADA Number CRD-13-514

DOE Office of Scientific and Technical Information (OSTI.GOV)

Terlip, Danny

2016-03-28

Diaphragm compressors have become the primary source of on-site hydrogen compression for hydrogen fueling stations around the world. NREL and PDC have undertaken two studies aimed at improving hydrogen compressor operation and reducing the cost contribution to dispensed fuel. The first study identified the failure mechanisms associated with mechanical compression to reduce the maintenance and down-time. The second study will investigate novel station configurations to maximize hydrogen usage and compressor lifetime. This partnership will allow for the simulation of operations in the field and a thorough analysis of the component failure to improve the reliability of diaphragm compression.

Southern California Edison Grid Integration Evaluation: Cooperative Research and Development Final Report, CRADA Number CRD-10-376

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mather, Barry

2015-07-09

The objective of this project is to use field verification to improve DOE’s ability to model and understand the impacts of, as well as develop solutions for, high penetration PV deployments in electrical utility distribution systems. The Participant will work with NREL to assess the existing distribution system at SCE facilities and assess adding additional PV systems into the electric power system.

Array Effects in Large Wind Farms. Cooperative Research and Development Final Report, CRADA Number CRD-09-343

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moriarty, Patrick

2016-02-23

The effects of wind turbine wakes within operating wind farms have a substantial impact on the overall energy production from the farm. The current generation of models drastically underpredicts the impact of these wakes leading to non-conservative estimates of energy capture and financial losses to wind farm operators and developers. To improve these models, detailed research of operating wind farms is necessary. Rebecca Barthelmie of Indiana University is a world leader of wind farm wakes effects and would like to partner with NREL to help improve wind farm modeling by gathering additional wind farm data, develop better models and increasemore » collaboration with European researchers working in the same area. This is currently an active area of research at NREL and the capabilities of both parties should mesh nicely.« less

Automated System for Aneuploidy Detection in Sperm Final Report CRADA No. TC-1364-96: Phase I SBIR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wyrobek, A. J.; Dunlay, R. T.

This project was a relationship between Lawrence Livermore National Laboratory (LLNL) and Biological Detection, Inc. (now known as Cellomics, Inc.) It was funded as a Phase I SBIR from the National Institutes of Health (NIH) awarded to Cellomics, Inc. with a subcontract to LLNL.

Sperm Scoring Using Multi-Spectral Flow Imaging and FISH-IS Final Report CRADA No. TC02088.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marchetti, F.; Morrissey, P. J.

This was to be a collaborative effort between The Regents of the University of California, Lawrence Livermore National Laboratory (LLNL) and Amnis Corporation, to develop an automated system for scoring sperm interphase cells for the presence of chromosomal abnormalities using fluorescence in situ hybridization and the Amnis ImageStream technology platform.

Medical Isotope Program: O-18, C-13, and Xe-129 Final Report CRADA No. TC-2043-02

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scheibner, K. F.; Fought, J.

This was a collaborative effort between the University of California, Lawrence Livermore National Laboratory (LLNL) and Spectra Gases, Inc., to develop new and cheaper sources of Oxgyen-18 (O-18), Carbon-13 (C-13), and Xenon-129 (Xe-129), and to develop new applications of these stable medical isotopes in medicine resulting in a substantial increase in stable isotopes that are important to human health sciences.

Development of Electrodeposited CIGS Solar Cells: Cooperative Research and Development Final Report, CRADA Number CRD-09-357

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neale, Nathan

2016-09-01

At present, most PV materials are fabricated by vacuum technologies. Some of the many disadvantages of vacuum technology are complicated instrumentation, material waste, high cost of deposition per surface area, and instability of some compounds at the deposition temperature. Solution-based approaches for thin-film deposition on large areas are particularly desirable because of the low capital cost of the deposition equipment, relative simplicity of the processes, ease of doping, uniform deposition on a variety of substrates (including interior and exterior of tubes and various nonplanar devices), and potential compatibility with high-throughput (e.g., roll-to-roll) processing. Of the nonsilicon solar photovoltaic device modulesmore » that have been deployed to date, those based on the n-CdS/p-CdTe is a leading candidate. Two features in the optical characteristics of CdTe absorber are particularly attractive for photovoltaic conversion of sunlight; (a) its energy bandgap of 1.5 eV, which provides an optimal match with the solar spectrum and thus facilitates its efficient utilization and (b) the direct mode of the main optical transition which results in a large absorption coefficient and turn permits the use of thin layer (1-2 um) of active material. Thin films of CdTe required for these devices have been fabricated by a variety of methods (e.g., vapor transport deposition, vacuum deposition, screen printing and close-spaced sublimation). Electrodeposition is another candidate deserves more attention. This project will focus on delivering low-cost, high efficiency electrodeposited CdTe-based device.« less

Optimization of Diode Laser System to Treat Benign Prostate Hyperplasia Final Report CRADA No. TSB-1154-95

DOE Office of Scientific and Technical Information (OSTI.GOV)

London, Richard A; Byrne, Mark

Benign prostate hyperplasia (BPH) is a pervasive condition of enlargement of the male prostate gland which leads to several urinary difficulties ranging from hesitancy to incontinence to kidney dysfunction in severe cases. Currently the most common therapy is transurethral resection of the prostate (TURP) utilizing an electrosurgical device. Although TURP is largely successful, new BPH therapy methods are desired to reduce the cost and recovery time, improve the success rate, and reduce side effects. Recently, lasers have been introduced for this purpose. Indigo Medical Inc. is currently engaged in the development, testing, and preparation for sales of a new diodemore » laser based BPH therapy system. The development is based on laboratory experiments, animal studies, and a limited FDA-approved clinical trial in the US and in other countries. The addition of sophisticated numerical modeling, of the sort that has been highly developed at Lawrence Livermore National Laboratory, can greatly aid in the design of the system and treatment protocol. The benefits to DOE include the maintenance and advancement of numerical modeling expertise in radiation-matter interactions of the sort essential for the stockpile stewardship, inertial confinement fusion, and advanced manufacturing, and the push on advanced scientific computational methods, ultimately in areas such as 3-D transport.« less

Reliability Evaluation of Next Generation Inverter: Cooperative Research and Development Final Report, CRADA Number CRD-12-478

DOE Office of Scientific and Technical Information (OSTI.GOV)

Paret, Paul

The National Renewable Energy Laboratory (NREL) will conduct thermal and reliability modeling on three sets of power modules for the development of a next generation inverter for electric traction drive vehicles. These modules will be chosen by General Motors (GM) to represent three distinct technological approaches to inverter power module packaging. Likely failure mechanisms will be identified in each package and a physics-of-failure-based reliability assessment will be conducted.

Modeling Parasitic Energy Losses and the Impact of Advanced Tribological Concepts on Fuel Efficiency - Final CRADA Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fenske, George

2016-11-28

Our primary task for this project was to perform FMEP calculations for a broad range of parameters including engine type [spark ignition (SI) or compression ignition (CI)], engine size, engine mode (speed and load), lubricant viscosity, asperity friction, surface finish, oil type (mineral or synthetic), and additive (friction modifier), as discussed previously [1–3]. The actual analysis was limited to a large diesel engine and it included both load and speed dependencies as well as lubricant viscosity and speed.

Graded Reflectivity Mirror for the Solid State Heat Capacity Laser Final Report CRADA No. TC-2085-04

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yamamoto, R.; Davis, J. A.

This was a collaborative effort between The Regents of the University of California, Lawrence Livermore National Laboratory (LLNL) and the Boeing Company, to develop a Graded Reflectivity Mirror (GRM) to achieve improved near field fill and higher brightness in the far field output of LLNL’s Solid State Heat Capacity Laser (SSHCL).

Rarefaction Shock Wave Cutter for Offshore Oil-Gas Platform Removal Final Report CRADA No. TC02009.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Glenn, L. A.; Barker, J.

This was a collaborative effort between Lawrence Livermore National Security, LLC/Lawrence Livermore National Laboratory (LLNL) (formerly the University of California) and Jet Research Center, a wholly owned division of Halliburton Energy Services, Inc. to design and prototype an improved explosive cutter for cutting the support legs of offshore oil and gas platforms.

The Use of Adjuvant Nutrition to Preserve and Increase Lean Body Mass in AIDS Patients with Muscle Wasting.

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2000-01-03

The studies conducted under this CRADA were aimed at determining if nutritional supplementation with HMb, in combination with glutamine and arginine can ameliorate the AIDS-associated wasting syndrome and in turn improve the clinical course of the disease.

Climbing The Knowledge Mountain - The New Solids Processing Design And Management Manual (Presentation)

EPA Science Inventory

The USEPA, Water Environment Federation (WEF) and Water Environment Research Foundation (WERF), under a Cooperative Research and Development Agreement (CRADA), are undertaking a massive effort to produce a Solids Processing Design and Management Manual (Manual). The Manual, repr...

Climbing The Knowledge Mountain - The New Solids Processing Design And Management Manual

EPA Science Inventory

The USEPA, Water Environment Federation (WEF) and Water Environment Research Foundation (WERF), under a Cooperative Research and Development Agreement (CRADA), are undertaking a massive effort to produce a Solids Processing Design and Management Manual (Manual). The Manual, repr...

Sandia National Laboratories:

Science.gov Websites

Technology Partnerships Business, Industry, & Non-Profits Government Universities Center for Development Agreement (CRADA) Strategic Partnership Projects, Non-Federal Entity (SPP/NFE) Agreements New Browse Technology Portfolios Technology Partnerships Business, Industry, & Non-Profits Government

LANDFILLS AS BIOREACTORS: RESEARH AT THE OUTER LOOP LANDFILL, LOUISVILLE, KENTUCKY; FIRST INTERIM REPORT

EPA Science Inventory

Interim report resulting from a cooperative research and development agreement (CRADA) between US EP A's Officeof Research and Development - National Risk Management Research Laboratory and a n ongoing field demonstration
of municipal waste landfills being operated as bioreact...

10 CFR 784.2 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... contracts, grants, agreements, understandings and other arrangements (including Cooperative Research and Development Agreements [CRADAs], Work for Others and User Facility agreements, which includes research, development, or demonstration work, and includes any assignment or substitution of the parties, entered into...

Verb-Final Typology

ERIC Educational Resources Information Center

Ogihara, Saeko

2010-01-01

This dissertation is a typological study of verb-final languages, the purpose of which is to examine various grammatical phenomena in verb-final languages to discover whether there are correlations between the final position of the verb and other aspects of grammar. It examines how finality of the verb interacts with argument coding in simple…

Sandia National Laboratories: Sandia National Laboratories: Missions:

Science.gov Websites

Transfer Browse Technology Portfolios Technology Partnerships Business, Industry, & Non-Profits Agreements Cooperative Research and Development Agreement (CRADA) Strategic Partnership Projects, Non-Federal atmospheric flight with emphasis on aerodynamics; navigation, guidance and control; and thermal protection

OUTER LOOP LANDFILL CASE STUDY

EPA Science Inventory

This presentation will describe the interim data reaulting from a CRADA between USEPA and Waste Management, Inc. at the outer Loop Landfill Bioreactor research project located in Louisville, KY. Recently updated data will be presented covering landfill solids, gas being collecte...

IN SITU BIOREMEDIATION IN A LANDFILL: LEACHATE CHEMICAL AND MICROBIAL PARAMETERS

EPA Science Inventory

In recent years the conversion of landfills to landfill bioreactors has received increased attention owing to potential economic and waste treatment benefits. The U.S. EPA has entered into a Cooperative Research and Development Agreement (CRADA), with Waste Management Inc., testi...

LEACHATE NITROGEN CONCENTRATIONS AND BACTERIAL NUMBERS FROM TWO BIOREACTOR LANDFILLS

EPA Science Inventory

The U.S. EPA and Waste Management Inc. have entered into a cooperative research and development agreement (CRADA) to study landfills operated as bioreactors. Two different landfill bioreactor configurations are currently being tested at the Outer Loop landfill in Louisville, KY...

Sandia National Laboratories: Research: Materials Science

Science.gov Websites

Technology Partnerships Business, Industry, & Non-Profits Government Universities Center for Development Agreement (CRADA) Strategic Partnership Projects, Non-Federal Entity (SPP/NFE) Agreements New research. Research Our research uses Sandia's experimental, theoretical, and computational capabilities to

Sandia National Laboratories: Research: Research Foundations: Engineering

Science.gov Websites

Technology Partnerships Business, Industry, & Non-Profits Government Universities Center for Development Agreement (CRADA) Strategic Partnership Projects, Non-Federal Entity (SPP/NFE) Agreements New engineering transitions in advanced, highly critical systems by integrating theory development, experimental

Nondestructive x-ray Scattering Characterization of High Temperature Superconducting Wires

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thurston, T R

The purpose of this CRADA was to characterize the structural properties of the superconductor material within the wires in order to determine which processing procedures produce the best superconductor texture and phase development, and hence the best ultimate current carrying capacity.

Glycobiology in yeast: production of bio-ative biopolymers and small molecules

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scheller, Henrik

The accomplished goals of the CRADA were the establishment of a yeast strain capable of producing levels of vanillin suitable for commercial production and the identification of novel glycosyltransferases to construct the biosynthetic pathway of a gum Arabic-variant in yeast.

COOPERATIVE RESEARCH AND DEVELOPMENT FOR APPLICATION OF CFD TO ESTIMATING HUMAN EXPOSURES TO ENVIRONMENTAL POLLUTANTS

EPA Science Inventory

Under a Cooperative Research and Development Agreement (CRADA), Fluent, Inc. and the US EPA National Exposure Research Laboratory (NERL) propose to improve the ability of environmental scientists to use computer modeling for environmental exposure to air pollutants in human exp...

Transport of pollutants in plumes and PEPES: a study of transport of pollutants in power plant plumes, urban and industrial plumes, and persistent elevated pollution episodes. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vaughan, W.M.

Because of the increased concern for the regional nature of secondary air pollutants (e.g., sulfates and oxidants) the U.S. Environmental Protection Agency (EPA) sponsored a major field program in the northeastern United States during the summer of 1980. Two EPA field programs were actually carried out simultaneously. One addressed persistent elevated pollution episodes, and the other continued the 1979 northeast regional oxidant study in developing part of the data base for the regional oxidant model. Field activities were based in Columbus, OH. Ten research aircraft and several mobile and stationary surface-monitoring platforms from three EPA contractors, seven Federal Agencies, andmore » four Universities participated in the intensive measurement program between 16 July and 15 August 1980. Pollutants measured included SO/sub 2/, NO, NOx, O/sub 3/, sulfate, nitrate, and aerosols. This report describes the contractors activities. Their aircraft logged over 350 flight hours in 100 missions ranging as far east as Laconia, NH, as far south as Montgomery, AL, as far west as Texarkana, AR, and as far north as Saginaw, MI. Descriptive analyses are summarized for urban plume missions and regional missions. The quality assurance program is described, showing the efforts made to develop a well coordinated data base. Sources for reports and data are provided.« less

Chemiresistor microsensors for in-situ monitoring of volatile organic compounds : final LDRD report.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas, Michael Loren; Hughes, Robert Clark; Kooser, Ara S.

2003-09-01

This report provides a summary of the three-year LDRD (Laboratory Directed Research and Development) project aimed at developing microchemical sensors for continuous, in-situ monitoring of volatile organic compounds. A chemiresistor sensor array was integrated with a unique, waterproof housing that allows the sensors to be operated in a variety of media including air, soil, and water. Numerous tests were performed to evaluate and improve the sensitivity, stability, and discriminatory capabilities of the chemiresistors. Field tests were conducted in California, Nevada, and New Mexico to further test and develop the sensors in actual environments within integrated monitoring systems. The field testsmore » addressed issues regarding data acquisition, telemetry, power requirements, data processing, and other engineering requirements. Significant advances were made in the areas of polymer optimization, packaging, data analysis, discrimination, design, and information dissemination (e.g., real-time web posting of data; see www.sandia.gov/sensor). This project has stimulated significant interest among commercial and academic institutions. A CRADA (Cooperative Research and Development Agreement) was initiated in FY03 to investigate manufacturing methods, and a Work for Others contract was established between Sandia and Edwards Air Force Base for FY02-FY04. Funding was also obtained from DOE as part of their Advanced Monitoring Systems Initiative program from FY01 to FY03, and a DOE EMSP contract was awarded jointly to Sandia and INEEL for FY04-FY06. Contracts were also established for collaborative research with Brigham Young University to further evaluate, understand, and improve the performance of the chemiresistor sensors.« less

Sandia National Laboratories: Strategic Partnership Projects, Non-Federal

Science.gov Websites

Technology Partnerships Business, Industry, & Non-Profits Government Universities Center for Development Agreement (CRADA) Strategic Partnership Projects, Non-Federal Entity (SPP/NFE) Agreements New Sandia Strategic Partnership Projects, Non-Federal Entity (SPP/NFE) Agreements Alt text Potential

21 CFR 516.141 - Qualified expert panels.

Code of Federal Regulations, 2012 CFR

2012-04-01

... funding from the requestor through a contract or research grant (either directly or indirectly through...), including for each the following: Name of the firm, topic/issue, amount received, date initiated. (iv) Contracts, grants, Cooperation Research and Development Agreement (CRADAs) (current or under negotiation...

21 CFR 516.141 - Qualified expert panels.

Code of Federal Regulations, 2013 CFR

2013-04-01

... funding from the requestor through a contract or research grant (either directly or indirectly through...), including for each the following: Name of the firm, topic/issue, amount received, date initiated. (iv) Contracts, grants, Cooperation Research and Development Agreement (CRADAs) (current or under negotiation...

21 CFR 516.141 - Qualified expert panels.

Code of Federal Regulations, 2014 CFR

2014-04-01

... funding from the requestor through a contract or research grant (either directly or indirectly through...), including for each the following: Name of the firm, topic/issue, amount received, date initiated. (iv) Contracts, grants, Cooperation Research and Development Agreement (CRADAs) (current or under negotiation...

Sandia National Laboratories: National Security Missions: Defense Systems

Science.gov Websites

Technology Partnerships Business, Industry, & Non-Profits Government Universities Center for Development Agreement (CRADA) Strategic Partnership Projects, Non-Federal Entity (SPP/NFE) Agreements New leadership for the national security community by delivering cutting-edge experimental and operational sensor

Sandia National Laboratories: Predicting Performance Margins

Science.gov Websites

Technology Partnerships Business, Industry, & Non-Profits Government Universities Center for Development Agreement (CRADA) Strategic Partnership Projects, Non-Federal Entity (SPP/NFE) Agreements New areas of Materials Sciences, leveraging both experimental and modeling expertise at Sandia. The PPM

Sandia National Laboratories: Careers: Materials Science

Science.gov Websites

Technology Partnerships Business, Industry, & Non-Profits Government Universities Center for Development Agreement (CRADA) Strategic Partnership Projects, Non-Federal Entity (SPP/NFE) Agreements New Sandia's experimental, theoretical, and computational capabilities to establish the state of the art in

Sandia National Laboratories: National Security Missions: Nuclear Weapons

Science.gov Websites

Technology Partnerships Business, Industry, & Non-Profits Government Universities Center for Development Agreement (CRADA) Strategic Partnership Projects, Non-Federal Entity (SPP/NFE) Agreements New , in which fundamental science, computer models, and unique experimental facilities come together so

Utility of Big Area Additive Manufacturing (BAAM) For The Rapid Manufacture of Customized Electric Vehicles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Love, Lonnie J.

This Oak Ridge National Laboratory (ORNL) Manufacturing Development Facility (MDF) technical collaboration project was conducted in two phases as a CRADA with Local Motors Inc. Phase 1 was previously reported as Advanced Manufacturing of Complex Cyber Mechanical Devices through Community Engagement and Micro-manufacturing and demonstrated the integration of components onto a prototype body part for a vehicle. Phase 2 was reported as Utility of Big Area Additive Manufacturing (BAAM) for the Rapid Manufacture of Customized Electric Vehicles and demonstrated the high profile live printing of an all-electric vehicle using ONRL s Big Area Additive Manufacturing (BAAM) technology. This demonstration generatedmore » considerable national attention and successfully demonstrated the capabilities of the BAAM system as developed by ORNL and Cincinnati, Inc. and the feasibility of additive manufacturing of a full scale electric vehicle as envisioned by the CRADA partner Local Motors, Inc.« less

Biodiesel/Cummins CRADA Report

DTIC Science & Technology

2014-07-01

sediment on the Racor turbine , coalescing centrifuge, check ball, and rubber seal pieces. The fuel flow sensor was opened, and a small obstruction was...is a wireless router that connects the computer (via BlueTooth) with a remote site (via the cellular network). This setup allowed the test team to...2 ¾” shaft on the BUSL. The data appeared to be accurate for short periods, and then appeared to lose calibration due to sensor misalignment

Butanol / Honda CRADA Report

DTIC Science & Technology

2015-02-01

study developed a test plan to test BU16 in CG boats, assessing boat performance, and the modifications required to use the fuel. The third study (and...current project) executed this test plan to quantify implementation issues, benefits and impacts of using the alternative fuel in CG boats under...4  2.2  Project 2: Test Plan Development

Sandia National Laboratories: Contact Us

Science.gov Websites

Technology Partnerships Business, Industry, & Non-Profits Government Universities Center for Development Agreement (CRADA) Strategic Partnership Projects, Non-Federal Entity (SPP/NFE) Agreements New )* Non-mail deliveries: 1515 Eubank SE Albuquerque, NM 87123 Sandia National Laboratories, California P.O

IN SITU BIOREMEDIATION IN A LANDFILL: HOLDING TIME STUDY OF LEACHATE CHEMICAL AND MICROBIAL PARAMETERS

EPA Science Inventory

Processing and analyzing solid waste samples from large and costly sampling events in a timely manner is often difficult. As part of a Cooperative Research and Development Agreement (CRADA), the U.S. EPA and Waste Management Inc. (WMI) are investigating the conversion of landfill...

Sandia National Laboratories: Pulsed-Power Science and Technology

Science.gov Websites

Technology Partnerships Business, Industry, & Non-Profits Government Universities Center for Development Agreement (CRADA) Strategic Partnership Projects, Non-Federal Entity (SPP/NFE) Agreements New and diagnostic tools to analyze results from Z and other experimental platforms. The results also

77 FR 19678 - Cooperative Research and Development Agreement: Asset Tracking and Reporting Technology

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-02

... Cooperative Research and Development Agreement (CRADA) with General Dynamics C4 Systems, Inc. (General Dynamics), to test, evaluate, and document the strengths and weaknesses of at least one technical approach... Guard is currently considering partnering with General Dynamics, we are soliciting public comment on the...

77 FR 25488 - Cooperative Research and Development Agreement: Federally Integrated Communications System

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-30

... Cooperative Research and Development Agreement (CRADA) with General Dynamics C4 Systems, Inc. to lab... operations of the Coast Guard's Rescue 21 system; (2) General Dynamics' capability to provide the significant... Development Agreement: Federally Integrated Communications System AGENCY: Coast Guard, DHS. ACTION: Notice of...

Predictive Engineering Tools for Injection-Molded Long-Carbon-Fiber Thermoplastic Composites - FY 2014 First Quarterly Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nguyen, Ba Nghiep; Sanborn, Scott E.; Simmons, Kevin L.

2014-02-19

The CRADA between PNNL, Autodesk, Toyota and Magna has been effective since October 28th, 2013. The whole team including CRADA and subcontract partners kicked off the project technically on November 1st, 2013. This report describes work performed during the first quarter of FY 2014. The following technical progresses have been made toward project milestones: 1) The project kickoff meeting was organized at PlastiComp, Inc. in Winona on November 13th, 2013 involving all the project partners. During this meeting the research plan and Gantt chart were discussed and refined. The coordination of the research activities among the partners was also discussedmore » to ensure that the deliverables and timeline will be met. 2) Autodesk delivered a research version of ASMI to PNNL for process modeling using this tool under the project. PNNL installed this research version on a PNNL computer and tested it. Currently, PNNL is using ASMI to prepare the models for PlastiComp plaques. 3) PlastiComp has compounded long carbon-fiber reinforced polypropylene and polyamide 6,6 compounds for rheological and thermal characterization tests by the Autodesk laboratories in Melbourne, Australia. 4) Initial mold flow analysis was carried out by PlastiComp to confirm that the 3D complex part selected by Toyota as a representative automotive part is moldable. 5) Toyota, Magna, PlastiComp and PNNL finalized the planning for molding the Toyota 3D complex part. 6) Purdue University worked with PNNL to update and specify the test matrix for characterization of fiber length/orientation. 7) Purdue University developed tools to automate the data collection and analysis of fiber length and orientation measurements. 8) Purdue University designed and specified equipment to replace the need for equipment using the technology established by the University of Leeds at General Motors.« less

Development of Plastic Substrate Technology for Active Matrix Liquid Crystal Displays Final Report CRADA No. TC-761-93

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carey, P.; Kamath, H.

Raychem Corporation (RYC) and the Lawrence Livermore National Laboratory (LLNL) conducted a development program with the goal to make rugged, low-cost., high-resolution flat panel displays based on RYC's proprietary Nematic Curvilinear Aligned Phase (NCAP) liquid crystal and LLNL's patented processes for the formation and doping of polycrystalline silicon on low-temperature, flexible, plastic substrates.

Development of Chemically Amplified Optical Sensors for Continuous Blood Glucose Monitoring Final Report CRADA No. TSB-1162-95

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lane, Stephen M.; Mastrototaro, John J.

Diabetes is a chronic disease that affects 14 million people in the U.S. and more than 110 million people worldwide. Each year in this country 27,000 diabetic patients become blind, 15,000 have kidney failure, and over 54,000 have peripheral limb amputations. In 1992, total healthcare costs in the U.S. for diabetes were more than $105 billion, approximately 15% of our healthcare budget. Conventional therapy for the most severe form of diabetes, insulin-dependent diabetes mellitus (IDDM) or Type I diabetes, is to administer one or two injections per day of various forms of insulin while monitoring blood glucose levels twice ormore » three times daily with commercial glucometers that require blood samples. Near normal blood sugar levels (glycemic control) is difficult to achieve with conventional therapy. In the fall of 1993, the results of the 10-year $165 million Diabetes Control and Complications Trial (DCCT) were published which showed that intensive insulin management would lead to dramatically fewer cases of retinopathy (which leads to blindness), nephropathy (which leads to kidney failure), and neuropathy (which can lead to limb amputations) [New England Journal of Medicine, Vo1239, No.14 977-986 (1993)]. If existing commercial insulin pumps could be combined with a continuous glucose sensor, a more physiological and fine-tuned therapy could be provided - in effect, an artificial biomechanical pancreas would be available. Existing research suggested that such a development would dramatically improve glucose control, thus greatly reducing morbidity and mortality from this disease. MiniMed Technologies in Sylmar, CA, identified a number of optically based sensor strategies as well as candidate chemical reactions that could be used to implement a minimally invasive opto-chemical glucose sensor. LLNL evaluated these sensor strategies and chemical reactions. These evaluations were the first steps leading to development of a sensor of considerable importance that could maintain near normal physiological glycemic levels, thus dramatically reducing the risk of the microvascular complications mentioned above.« less

Community Energy Storage Thermal Analysis and Management: Cooperative Research and Development Final Report, CRADA Number CRD-11-445

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, Kandler A.

The goal of this project is to create thermal solutions and models for community energy storage devices using both purpose-designed batteries and EV or PHEV batteries. Modeling will be employed to identify major factors of a device's lifetime and performance. Simultaneously, several devices will be characterized to determine their electrical and thermal performance under controlled conditions. After the factors are identified, a variety of thermal design approaches will be evaluated to improve the performance of energy storage devices. Upon completion of this project, recommendations for community energy storage device enclosures, thermal management systems, and/or battery sourcing will be made. NREL'smore » interest is in both new and aged batteries.« less

Development, Manufacturing, and Preparation for Serial Production of Low Noise Seismometers Final Report CRADA No. TC02096.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vergino, E. S.; Passmore, P. R.

2012-01-23

This was a collaborative effort between Lawrence Livermore National Security, LLC as manager and operator of Lawrence Livermore National Laboratory (LLNL) and Refraction Technology, Inc. (REF TEK), to collaborate on the development of a broadband, competitive low-noise seismometer, rugged and easy to use for field deployments. The work involved collaborative work between LLNL, REF TEK and a group led by Federal State Unitary Enterprise, Research Institute of Pulse Technique (RIPT), Moscow, Russia. The proposed work focused on bringing an improved version of the Russian SDSE seismometer from development phase to production in two versions. The first was a very lowmore » cost, rugged, broadband seismometer for field deployment that would achieve noise levels comparable to the standard earth low noise model (LNM) of the USGS. All three components were integrated into one case, and have sensitivity near 2000 v/m/s, and analog output with bandwidth of .01 to 40 Hz with high coherence.« less

Research and Development of Zinc Air Fuel Cell To Achieve Commercialization Final Report CRADA No. TC-1544-98

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cooper, J. F.; Haley, H. D.

The specific goal of this project was to advance the development of the zinc air fuel cell (ZAFC) towards commercial readiness in different mobile applications, including motor bikes, passenger cars, vans, buses and off-road vehicles (golf carts, factory equipment), and different stationary applications including generator sets, uninterruptible power systems and electric utility loading leveling and distributive power.

Mobile Building Energy Audit and Modeling Tools: Cooperative Research and Development Final Report, CRADA Number CRD-11-00441

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brackney, L.

Broadly accessible, low cost, accurate, and easy-to-use energy auditing tools remain out of reach for managers of the aging U.S. building population (over 80% of U.S. commercial buildings are more than 10 years old*). concept3D and NREL's commercial buildings group will work to translate and extend NREL's existing spreadsheet-based energy auditing tool for a browser-friendly and mobile-computing platform. NREL will also work with concept3D to further develop a prototype geometry capture and materials inference tool operable on a smart phone/pad platform. These tools will be developed to interoperate with NREL's Building Component Library and OpenStudio energy modeling platforms, and willmore » be marketed by concept3D to commercial developers, academic institutions and governmental agencies. concept3D is NREL's lead developer and subcontractor of the Building Component Library.« less

Demonstration of Laser Plasma X-Ray Source with X-Ray Collimator Final Report CRADA No. TC-1564-99

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lane, S. M.; Forber, R. A.

2017-09-28

This collaborative effort between the University of California, Lawrence Livermore National Laboratory (LLNL) and JMAR Research, Inc. (JRI), was to demonstrate that LLNL x-ray collimators can effectively increase the wafer throughput of JRI's laser based x-ray lithography systems. The technical objectives were expected to be achieved by completion of the following tasks, which are separated into two task lists by funding source. The organization (LLNL or JMAR) having primary responsibility is given parenthetically for each task.

Hyperspectral Geobotanical Remote Sensing for Monitoring and Verifying CO 2 Containment Final Report CRADA No. TC-2036-02

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pickles, W. L.; Ebrom, D. A.

This collaborative effort was in support of the CO 2 Capture Project (CCP), to develop techniques that integrate overhead images of plant species, plant health, geological formations, soil types, aquatic, and human use spatial patterns for detection and discrimination of any CO 2 releases from underground storage formations. The goal of this work was to demonstrate advanced hyperspectral geobotanical remote sensing methods to assess potential leakage of CO 2 from underground storage. The timeframes and scales relevant to the long-term storage of CO 2 in the subsurface make remote sensing methods attractive. Moreover, it has been shown that individual fieldmore » measurements of gas composition are subject to variability on extremely small temporal and spatial scales. The ability to verify ultimate reservoir integrity and to place individual surface measurements into context will be crucial to successful long-term monitoring and verification activities. The desired results were to produce a defined and tested procedure that could be easily used for long-term monitoring of possible CO 2 leakage from underground CO 2 sequestration sites. This testing standard will be utilized on behalf of the oil industry.« less

Design of 3x3 Focusing Array for Heavy Ion Driver Final Report on CRADA TC-02082-04

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martovetsky, N.

This memo presents a design of a 3x3 quadrupole array for HIF. It contains 3 D magnetic field computations of the array build with racetrack coils with and without different shields. It is shown that it is possible to have a low error magnetic field in the cells and shield the stray fields to acceptable levels. The array design seems to be a practical solution to any size array for future multi-beam heavy ion fusion drivers.

Solar Technology Validation Project - RES Americas: Cooperative Research and Development Final Report, CRADA Number CRD-09-367-11

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilcox, S.

Under this Agreement, NREL will work with Participant to improve concentrating solar power system performance characterizations. This work includes, but is not limited to, research and development of methods for acquiring renewable resource characterization information using site-specific measurements of solar radiation and meteorological conditions; collecting system performance data; and developing tools for improving the design, installation, operation, and maintenance of solar energy conversion systems. This work will be conducted at NREL and Participant facilities.

Extraction of Iodine from Source Rock and Oil for Radioiodine Dating Final Report CRADA No. TC-1550-98

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moran, J. E.; Summa, L.

This was a collaborative effort between the University of California, Lawrence Livermore National Laboratory (LLNL) and Exxon Production Research Company (EPR) to develop improved techniques for extracting, concentrating, and measuring iodine from large volumes of source rock and oil. The purpose of this project was to develop a technique for measuring total iodine extracted from rock, obtain isotopic ratios, and develop age models for samples provided by EPR.

Analysis and Design of a Fiber-optic Probe for DNA Sensors Final Report CRADA No. TSB-1147-95

DOE Office of Scientific and Technical Information (OSTI.GOV)

Molau, Nicole; Vail, Curtis

In 1995, a challenge in the field of genetics dealt with the acquisition of efficient DNA sequencing techniques for reading the 3 billion base-pairs that comprised the human genome. AccuPhotonics, Inc. proposed to develop and manufacture a state-of-the-art near-field scanning optical microscopy (NSOM) fiber-optic probe that was expected to increase probe efficiency by two orders of magnitude over the existing state-of-the-art and to improve resolution to 10Å. The detailed design calculation and optimization of electrical properties of the fiber-optic probe tip geometry would be performed at LLNL, using existing finite-difference time-domain (FDTD) electromagnetic (EM) codes.

Great Lakes/St. Lawrence Seaway Regional Transportation Study for U.S. Army Corps of Engineers.

DTIC Science & Technology

1982-04-01

LAKE HURON Two Harbors, MN Saginaw, MI Duluth-Superior, MN-WI St. Clair River, MI, St. Clair Presque Isle , MI Port of Detroit, MI Marquette, MI Detroit...Port Dolomite, MI Green Bay, WI LAKE ERIE Milwaukee, WI Chicago, IL Toledo, OH Calumet Harbor, IN-IL Sandusky, OH Lake Calumet Huron, OH Indiana Harbor...IN Lorain, OH Burns Waterway, IN Cleveland, OH Muskegon, MI Ashtabula, OH Gary, IN Conneaut, OH Escanaba, MI Erie , PA Grand Haven, MI Port of Buffalo

Forest Species Identification with High Spectral Resolution Data

NASA Technical Reports Server (NTRS)

Olson, C. E., Jr.; Zhu, Z.

1985-01-01

Data collected over the Sleeping Bear Sand Dunes Test Site and the Saginaw Forest Test Site (Michigan) with the JPL Airborne Imaging Spectrometer and the Collins' Airborne Spectroradiometer are being used for forest species identification. The linear discriminant function has provided higher identification accuracies than have principal components analyses. Highest identification accuracies are obtained in the 450 to 520 nm spectral region. Spectral bands near 1,300, 1,685 and 2,220 nm appear to be important, also.

Sandia National Laboratories: Employee & Retiree Resources

Science.gov Websites

, visit hbe.sandia.gov. Click on the group that applies to you - active represented, active non Technology Partnerships Business, Industry, & Non-Profits Government Universities Center for Development Agreement (CRADA) Strategic Partnership Projects, Non-Federal Entity (SPP/NFE) Agreements New

Frankenmuth Dam Fish Passage, Cass River, Saginaw County, Michigan

DTIC Science & Technology

2012-11-01

2009letter, our office and the Alpena Fish and Wildlife Conservation Office have been worldng with you to develop monitoring programs to assess changes...Sargent. MDNR. Wildlife Division. Lansing, MI Andrea Ania, USFWS, Alpena , M1 EA - C-7 ZIIBIWING CENTER ot A~t.:..~ c •. lt • .,..~ 1’¥- ,..1

Wave Data Acquisition and Hindcast for Saginaw Bay, Michigan.

DTIC Science & Technology

1983-06-01

Bretschneider (1952) and Mitsuyasu and Kimura (1965) for f the peak fre- %m quency (where fm = f g/U) while the total energy decay rate follows that mm...Spectra of Wind-Generated Gravity Waves," Journal of Physical Oceanography, Vol 5, pp 410-420. Mitsuyasu, Hisashi . 1968. "On the Growth of the...8217 . , / . - . ’ -’ -. .. ’ . .. _..- -’ - Mitsuyasu, Hisashi , and Kirmura, Hisao. 1965. "Wind Wave in Decay Area," Coastal Engineering in Japan, Vol 8, pp 221-35. Ou, Shan-Hwei. 1980 (Sep

Sandia National Laboratories: Agreements

Science.gov Websites

Technology Partnerships Business, Industry, & Non-Profits Government Universities Center for Development Agreement (CRADA) Strategic Partnership Projects, Non-Federal Entity (SPP/NFE) Agreements New Projects, Non-Federal Entity (SPP/NFE) Agreements Sandia performs work on a reimbursable basis for a non

76 FR 78290 - Cooperative Research and Development Agreement: Usage of Biodiesel Fuel Blends Within Marine...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-16

... Development Agreement: Usage of Biodiesel Fuel Blends Within Marine Inboard Engines AGENCY: Coast Guard, DHS... issues associated with using biodiesel fuel blends in marine inboard engines, with the overarching goal... participant in a CRADA similar to the one described in this notice (investigating the use of biodiesel fuel...

Gated Field-Emission Cathode Radio-Frequency (RF) Gun

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fermi Research Alliance, Fermi Alliance

The goal of this CRADA was to procure the carbon nanotube cathode from Radiabeam, install it in HBESL and make current measurements as a function of the gun gradient. The gun was operated at 1.3 GHz. After testing, send the cathode back to RadiaBeam for surface analysis.

Distribution and abundance of larval fish in the nearshore waters of western Lake Huron

USGS Publications Warehouse

O'Gorman, Robert

1983-01-01

Ichthyoplankton was collected at 17 nearshore (bottom depth ≥5 m but ≤10 m) sites in western Lake Huron during 1973–75 with a 0.5-m net of 351-micron mesh towed at 99 m/min. Larvae of rainbow smelt (Osmerus mordax) dominated late spring and early summer catches and larvae of alewives (Alosa pseudoharengus) the midsummer catches. Larval yellow perch (Perca flavescens) were caught in early summer but were rarely the dominant species. The time of spawning and hatching, and thus occurrence of larvae, differed between areas but was less variable for alewives than for yellow perch. The appearance of larvae in Saginaw Bay was followed successively by their appearance in southern, central, and northern Lake Huron. Rainbow smelt were most abundant in northern Lake Huron and yellow perch and alewives in inner Saginaw Bay. Densities of either rainbow smelt or alewives occasionally exceeded 1/m3, whereas those of yellow perch never exceeded 0.1/m3. Abundance of alewives was usually highest 1 to 3 m beneath the surface and that of rainbow smelt 2 to at least 6 m beneath the surface. Important nursery areas of rainbow smelt were in bays and off irregular coastlines and those of yellow perch were in bays. All nearshore waters seemed equally important as nursery areas of alewives.

Age and growth of round gobies in Lake Huron: Implications for food web dynamics

USGS Publications Warehouse

Duan, You J.; Madenjian, Charles P.; Xie, Cong X.; Diana, James S.; O'Brien, Timothy P.; Zhao, Ying M.; He, Ji X.; Farha, Steve A.; Huo, Bin

2016-01-01

Although the round goby (Neogobius melanostomus) has become established throughout the Laurentian Great Lakes, information is scarce on spatial variation in round goby growth between and within lakes. Based on a sample of 754 specimens captured in 2014, age, growth, and mortality of round gobies at four locations in Lake Huron were assessed via otolith analysis. Total length (TL) of round gobies ranged from 44 to 111 mm for Saginaw Bay, from 45 to 115 mm for Rockport, from 50 to 123 mm for Hammond Bay, and from 51 to 118 mm for Thunder Bay. Estimated ages of round gobies ranged from 2 to 5 years for Saginaw Bay, from 2 to 6 years for Rockport, and from 2 to 7 years for Hammond Bay and Thunder Bay. Sex-specific, body–otolith relationships were used to back-calculate total lengths at age, which were then fitted to von Bertalanffy growth models. For each sex, round goby growth showed significant spatial variation among the four locations within Lake Huron. At all four locations in Lake Huron, males grew significantly faster than females and attained a larger asymptotic length than females. Annual mortality rate estimates were high (62 to 85%), based on catch-curve analysis, suggesting that round gobies may be under predatory control in Lake Huron.

Evaluation of Subsurface Flow and Free-water Surface Wetlands Treating NPR-3 Produced Water - Year No. 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Myers, J. E.; Jackson, L. M.

2001-10-13

This paper is a summary of some of the activities conducted during the first year of a three-year cooperative research and development agreement (CRADA) between the Department of Energy (DOE) Rocky Mountain Oilfield Testing Center (RMOTC) and Texaco relating to the treatment of produced water by constructed wetlands. The first year of the CRADA is for design, construction and acclimation of the wetland pilot units. The second and third years of the CRADA are for tracking performance of pilot wetlands as the plant and microbial communities mature. A treatment wetland is a proven technology for the secondary and tertiary treatmentmore » of produced water, storm water and other wastewaters. Treatment wetlands are typically classified as either free-water surface (FWS) or subsurface flow (SSF). Both FWS and SSF wetlands work well when properly designed and operated. This paper presents a collection of kinetic data gathered from pilot units fed a slipstream of Wyoming (NPR-3) produced water. The pilot units are set up outdoors to test climatic influences on treatment. Monitoring parameters include evapotranspiration, plant growth, temperature, and NPDES discharge limits. The pilot wetlands (FWS and SSF) consist of a series of 100-gal plastic tubs filled with local soils, gravel, sharp sand and native wetland plants (cattail (Typha spp.), bulrush (Scirpus spp.), dwarf spikerush (Eleocharis)). Feed pumps control hydraulic retention time (HRT) and simple water control structures control the depth of water. The treated water is returned to the existing produced water treatment system. All NPDES discharge limits are met. Observations are included on training RMOTC summer students to do environmental work.« less

Sandia National Laboratories: Facts & Figures

Science.gov Websites

Technology Partnerships Business, Industry, & Non-Profits Government Universities Center for Development Agreement (CRADA) Strategic Partnership Projects, Non-Federal Entity (SPP/NFE) Agreements New 1,615.2 Defense Nuclear Nonproliferation 204.2 Other NNSA 1.2 NON-NNSA DOE 2,061.1M Energy & Threat

Work with Us | Hydrogen and Fuel Cells | NREL

Science.gov Websites

agreements. Use our cutting-edge research facilities to develop, test, and evaluate hydrogen and fuel cell science behind emerging hydrogen and fuel cell technologies and develop, test, and validate new for qualified partners to participate in cooperative research and development agreement (CRADA

Final Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Glasser, Alan H.

Final technical report on DE-SC0016106. This is the final technical report for a portion of the multi-institutional CEMM project. This report is centered around 3 publications and a seminar presentation, which have been submitted to E-Link.

Ionic Liquids as Multi-Functional Lubricant Additives to Enhance Engine Efficiency (final report NFE-12-03876)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Qu, Jun; Luo, Huimin; Toops, Todd J.

This ORNL-Shell CRADA developed and investigated ionic liquids (ILs) as multifunctional additives for next-generation low-viscosity engine oils. Several groups of oil-miscible ILs were successfully designed and synthesized with high thermal stability, non-corrosiveness, excellent wettability, and most importantly effective anti-scuffing/anti-wear and friction reduction characteristics. Synergistic effects between the common anti-wear additive zinc dialkyldithiophosphate (ZDDP) and a particular group of ILs were discovered with > 30% friction reduction and 70% wear reduction compared with using ZDDP or IL alone. The IL+ZDDP tribofilm distinguishes itself from the IL or ZDDP tribofilms with substantially higher contents of metal phosphates but less metal oxides andmore » sulfur compounds. Notably, it was revealed that the actual concentrations of functional elements on the droplet surface of the oil containing IL+ZDDP are one order magnitude higher than their nominal values. Such significantly increased concentrations of anti-wear agents are presumably expected for the oilsolid interface and believed to be responsible for the superior lubricating performance. A prototype SAE 0W-16 engine oil using a synergistic IL+ZDDP pair as the anti-wear additive has been formulated based on the compatibility between the IL and other additives. Sequence VIE full-scale engine dynamometer tests demonstrated fuel economy improvement (FEI) for this prototype oil and revealed the individual contributions from the lower oil viscosity and reduced boundary friction. The impact of IL and IL+ZDDP on exhaust emission catalyst was investigated using an accelerated small engine aging test and results were benchmarked against ZDDP.« less

Antiperspirant drug products for over-the-counter human use; final monograph. Final rule.

PubMed

2003-06-09

The Food and Drug Administration (FDA) is issuing a final rule in the form of a final monograph establishing conditions under which over-the-counter (OTC) antiperspirant drug products are generally recognized as safe and effective and not misbranded as part of FDA's ongoing review of OTC drug products. FDA is issuing this final rule after considering public comments on its proposed regulation, issued as a tentative final monograph (TFM), and all new data and information on antiperspirant drug products that have come to the agency's attention.

Treatment of Produced Water From Coal-Bed Methane Production Using Capacitive Deionization Final Report CRADA No. TSV-1380-97

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tran, T. D.; Patton, C. C.

The production af Coal-Bed Methane (CBM) is always accompanied by the production of large amounts of water. The produced water is typically too high in dissolved solids and salinity to be suitable for surface disposal.

A Compact, Portable, Reduced-Cost, Gamma Ray Spectroscopic System for Nuclear Verification Final Report CRADA No. TSB-1551-98

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lavietes, A.; Kalkhoran, N.

The overall goal of this project was to demonstrate a compact gamma-ray spectroscopic system with better energy resolution and lower costs than scintillator-based detector systems for uranium enrichment analysis applications.

Solar Technology Validation Project - USS Data, LLC: Cooperative Research and Development Final Report, CRADA Number CRD-09-367-04

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilcox, S.

2013-08-01

Under this Agreement, NREL will work with Participant to improve concentrating solar power system performance characterizations. This work includes, but is not limited to, research and development of methods for acquiring renewable resource characterization information using site-specific measurements of solar radiation and meteorological conditions; collecting system performance data; and developing tools for improving the design, installation, operation, and maintenance of solar energy conversion systems. This work will be conducted at NREL and Participant facilities.

Operations under the Airport and Airway Development Act of 1970 as Amended by the Airport and Airway Development Act Amendments of 1976.

DTIC Science & Technology

1979-01-01

runway (3,000’ x Presque Isle County 60’); construct and mark taxiway and apron; relocate or raise runway lights. Saginaw 01 793,600 Land reimbursement...selected were Arizona, Michigan, Pennsylvania , and South Dakota. Actual grant activity began for these four states in FY 1977 with the issuance of grant...2,029,071 $3,659,971 Pennsylvania $2,482,430 $1,586,807 $4,069,237 South Dakota $ 687,862 $ 678,838 $1,366,700 An evaluation report on the results of the

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gatchett, A.M.; Fradkin, L.; Moore, M.

In 1986, the Federal Technology Transfer Act (FTTA) was established to promote a closer, collaborative relationship between federal government agencies and the private sector. With the increasing need for new cost-effective technologies to prevent and control pollution, both the US Environmental Protection Agency (EPA) and private industry are encouraged to facilitate the transfer of knowledge and technology under this Act. The FTTA removed several of the legal and institutional barriers to cooperative research that existed before the Act`s passage. Through the FTTA, the government strives to promote the movement of its products, processes, skills, and knowledge into the private sectormore » for further development and commercialization by encouraging the exchange of technical personnel and the sharing of facilities and other resources. Collaborative efforts between industry, federal agencies, and academia are made possible through cooperative research and development agreements (CRADAs). Forty-two CRADAs and five licensing agreements have been initiated with EPA under this program. This paper provides an overview of this new and innovative program within the EPA. 1 fig., 2 tabs.« less

Characterization of three-way automotive catalysts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kenik, E.A.; More, K.L.; LaBarge, W.

1997-04-01

The CRADA between Delphi Automotive Systems (Delphi; formerly General Motors - AC Delco, Systems) and Lockheed Martin Energy Research (LMER) on automotive catalysts was completed at the end of FY96, after a ten month, no-cost extension. The CRADA was aimed at improved performance and lifetime of noble metal based three-way-catalysts (TWC), which are the primary catalytic system for automotive emission control systems. While these TWC can meet the currently required emission standards, higher than optimum noble metal loadings are often required to meet lifetime requirements. In addition, more stringent emission standards will be imposed in the near future, demanding improvedmore » performance and service life from these catalysts. Understanding the changes of TWC conversion efficiency with ageing is a critical need in improving these catalysts. Initially in a fresh catalyst, the active material is often distributed on a very fine scale, approaching single atoms or small atomic clusters. As such, a wide range of analytical techniques have been employed to provide high spatial resolution characterization of the evolving state of the catalytic material.« less

Finite element analysis of constrained total Condylar Knee Prosthesis

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1998-07-13

could be selected for production. Because of unanticipated delays in the CRADA funding, the knee design had to be finalized before the analysis could be accomplished. Thus, the scope of work was modified by the industrial partner. It was decided that it would be most beneficial to perform FEA that would closely replicate the lab tests that had been done as the basis of the design. Exactech was responsible for transmitting the component geometries to Livermore, as well as providing complete data from the quasi-static laboratory loading tests that were performed on various designs. LLNL was responsible for defining the basic finite element mesh and carrying out the analysis. We performed the initial computer simulation and verified model integrity, using the laboratory data. After performing the parametric studies, the results were reviewed with Exactech. Also, the results were presented at the Orthopedic Research Society meeting in a poster session.« less

Butanol / Gasoline Mercury CRADA Report

DTIC Science & Technology

2015-03-01

oxygenated fuel, which increases in-cylinder temperatures and thus generates higher NOx emissions. 3.2 Modifications to the SPC-TB 3.2.1 Data Collection...emissions.  Emissions of oxides of Nitrogen (NOx) are higher with oxygenated fuel. NOx generation is a function of the time spent at high temperature ...pressure in the combustion chamber. The engines run leaner and hotter with oxygenated fuel, which increases in-cylinder temperatures and thus

Connecting Tech to Market in New Ways - Continuum Magazine | NREL

Science.gov Websites

as they run a test at the Energy Systems Integration Facility. Photo by Dennis Schroeder, NREL working together in a CRADA. Photo by Dennis Schroeder, NREL "It was hugely successful. We were able . Photo by Dennis Schroeder, NREL Sometimes the path to partnership gets a push from chance that adds

U. S. Pacific Fleet. Central Pacific Force. Operation Plan Number Cen 1-43

DTIC Science & Technology

1943-10-25

50.2 TG 50.2 CTG 50.3 TG 50.3 CTG 50.4 TG 50.4 CTG 50.5 TG 50.5 CTG 50.6 TG 50.6 Coronet Caucus Anz&e Mqrocco Rugby Tomahawk Anzac • Bluejacket...Ginger snap Maxwell Anzac Rugby Molly Potluck Garfield Rustic 1 Rustic 2 Rustic 3 Rustic 4 Rustic 5 Trigger 1 Trigger 2 Trigger 3 Trigger 4 Trigger 5...Yonkers Scranton LaCrosce Journal De Soto Hardtack I-iiiriot Tripod Stockade Einstein SAGINAW Chicago Glencoe Romeo Morocco GeroniiAo San Jiateo Rugby

20 CFR 636.11 - Final action.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Final action. 636.11 Section 636.11 Employees... HEARINGS § 636.11 Final action. The final decision of the Secretary pursuant to section 166(b) of the Act... Officer's final determination where there has been no such hearing, constitutes final agency action within...

20 CFR 636.11 - Final action.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 20 Employees' Benefits 3 2011-04-01 2011-04-01 false Final action. 636.11 Section 636.11 Employees... HEARINGS § 636.11 Final action. The final decision of the Secretary pursuant to section 166(b) of the Act... Officer's final determination where there has been no such hearing, constitutes final agency action within...

10 CFR 51.93 - Distribution of final environmental impact statement and supplement to final environmental impact...

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Distribution of final environmental impact statement and supplement to final environmental impact statement; news releases. 51.93 Section 51.93 Energy NUCLEAR... statement and supplement to final environmental impact statement; news releases. (a) A copy of the final...

10 CFR 51.93 - Distribution of final environmental impact statement and supplement to final environmental impact...

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 2 2013-01-01 2013-01-01 false Distribution of final environmental impact statement and supplement to final environmental impact statement; news releases. 51.93 Section 51.93 Energy NUCLEAR... statement and supplement to final environmental impact statement; news releases. (a) A copy of the final...

10 CFR 51.93 - Distribution of final environmental impact statement and supplement to final environmental impact...

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 2 2011-01-01 2011-01-01 false Distribution of final environmental impact statement and supplement to final environmental impact statement; news releases. 51.93 Section 51.93 Energy NUCLEAR... statement and supplement to final environmental impact statement; news releases. (a) A copy of the final...

10 CFR 51.93 - Distribution of final environmental impact statement and supplement to final environmental impact...

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 2 2012-01-01 2012-01-01 false Distribution of final environmental impact statement and supplement to final environmental impact statement; news releases. 51.93 Section 51.93 Energy NUCLEAR... statement and supplement to final environmental impact statement; news releases. (a) A copy of the final...

10 CFR 51.93 - Distribution of final environmental impact statement and supplement to final environmental impact...

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 2 2014-01-01 2014-01-01 false Distribution of final environmental impact statement and supplement to final environmental impact statement; news releases. 51.93 Section 51.93 Energy NUCLEAR... statement and supplement to final environmental impact statement; news releases. (a) A copy of the final...

Food of the American smelt in Saginaw Bay, Lake Huron

USGS Publications Warehouse

Gordon, William G.

1961-01-01

In order to determine possible sources of vitamin A for quail, 37 species of insects and other invertebrates were analyzed for vitamin A and for carotene, and 26 species of seeds and fruits were assayed for carotene. The invertebrates showed no trace of vitamin A; but 8 herbivorous invertebrates and the praying mantis contained carotene. Most of the plants contained carotene--some of them a lot (dotted smartweed, some legumes, sumac, roses, bittersweet, etc.). The amount of carotene varied among plants of the same species and even among fruits on the same plant.

Performance and economic evaluation of the seahorse natural gas hot water heater conversion at Fort Stewart. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Winiarski, D.W.

1995-12-01

The Federal government is the largest single energy consumer in the United States with consumption of nearly 1.5 quads/year of energy (10{sup 15} quad = 1015 Btu) and cost valued at nearly $10 billion annually. The US Department of Energy`s (DOE) Federal Energy Management Program (FEMP) supports efforts to reduce energy use and associated expenses in the Federal sector. One such effort, the New Technology Demonstration Program (NTDP) seeks to evaluate new energy -- saving US technologies and secure their more timely adoption by the US government. Pacific Northwest Laboratory (PNL) is one of four DOE laboratories that participate inmore » the New Technologies Demonstration Program, providing technical expertise and equipment to evaluate new, energy-saving technologies being studied under that program. This report provides the results of a field evaluation that PNL conducted for DOE/FEMP with funding support from the US Department of Defense (DoD) Strategic Environmental Research and Development Program (SERDP) to examine the performance of 4 candidate energy-saving technology-a water heater conversion system to convert electrically powered water heaters to natural gas fuel. The unit was installed at a single residence at Fort Stewart, a US Army base in Georgia, and the performance was monitored under the NTDP. Participating in this effort under a Cooperative Research and Development Agreement (CRADA) were Gas Fired Products, developers of the technology; the Public Service Company of North Carolina; Atlanta Gas Light Company; the Army Corps of Engineers; Fort Stewart; and Pacific Northwest Laboratory.« less

Novel Biocatalytic Platform for Ethanol Production from Lignocellulosic Feedstock

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Chyi-Shin; Tachea, Firehiwot; Brown, Sarah

2017-01-23

The goals of the CRADA were achieved by illustrating the scalability of immobilized yeast technology, demonstrating lignocellulosic feedstock consumption by the immobilized cells, and confirming Microvi’s proprietary polymer matrix ethanol toxicity tolerance. We conducted fermentations at 2L and 300L scales. For carbon source, we performed pretreatment and saccharification at 100L scale to produce lignocellulosic sugars with glucose and xylose.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Verce, M. F.; Schwartz, L. I.

This was a collaborative effort between LLNL and STE to investigate the use of vaporized hydrogen peroxide (VHP®) to decontaminate spore-contaminated heating, ventilation, and cooling (HV AC) systems in a trailer sized room. LLNL's effort under this CRADA was funded by DOE's Chemical and Biological National Security Program (CBNP), which later became part of Department of Homeland Security in 2004.

Supply Chain Resilience: Assessing Resilience over the Life Cycle of Capital Equipment

DTIC Science & Technology

2014-07-09

Purposes): [] CRADA (Cooperative Research and Development Agreement) exists [] Photo/ Video Opportunities [] STEM -outreach Related [] New Invention...Recovery C9 10.6 / 0.7 9.8 / -1.1 Dispersion ClO 8.4 13.4 15.3 /11.0 Collaboration Cll -0.1 I -10.5 3.6 / -9.0 Organization Cl2 6.3 / -3.2 Security C l3

Synthesis of a Novel Energetic Heterocyclic Oxidizer with Higher Energy and Lower Sensitivity Final Report CRADA No. TC02099.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pagoria, P.; Racoveanu, A.

2017-09-08

The project involved the synthesis of 5g of a target energetic compound, 3,4-bis(5-nitro-1,2,5- oxadiazol-4-yl)-1,2,5-oxadiazole-1-oxide (DNTF. The deliverables were the synthesis of 5g of DNTF along with quantities of the precursor compounds. In addition, small-scale safety tests on DNTF were performed, which to confirmed that DNTF has no undesirable safety properties before scaling up the synthesis in Phase II of this project.

Investigations into Performance and Lifetime Enhancements of OPV Devices: Cooperative Research and Development Final Report, CRADA Number CRD-08-263

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ginley, D.

2014-06-01

To evaluate Plextronics new additives and derivatives in lithium-ion Battery Applications, Plextronics will provide to NREL, a starting point, including materials and initial data for proof of concept. The central focus of this project is to acertain the nature of the efficacy of the Plextronics additives through physical and electrical characterization, including evaluations of new derivatives, system evaluations on batteries made with Plexcore and to study long term cycling performance differences. The initial focus is to establish Plexcore mode of action to support the commercialization of the first commercial evaluations of Plexcore in Sept. 2013.

Development of an Ultra-Low-Cost Solar Water Heater: Cooperative Research and Development Final Report, CRADA Number CRD-12-487

DOE Office of Scientific and Technical Information (OSTI.GOV)

Merrigan, Tim

2016-02-17

NREL and RhoTech will collaborate to bring long-lived, ultra-low-cost, high-performance solar water heaters (SWH) to market readiness. An existing RhoTech design uses seam-welded polymer thin films to make an unglazed thermosiphon, and this design will be modified to improve durability through ultraviolet and overheat protection, and to improve performance by adding a glazing to the collector. Two generations of the new glazed systems will be tested in the field, resulting in a robust market-ready SWH design that can be installed for under $1,000 without rebates.

Xylo-Oligosaccharide Process Development, Composition, and Techno-Economic Analysis. Cooperative Research and Development Final Report, CRADA Number CRD-12-483

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shekiro, Joe; Elander, Richard

2015-12-01

The purpose of this cooperative work agreement between General Mills Inc. (GMI) and NREL is to determine the feasibility of producing a valuable food ingredient (xylo-oligosaccharides or XOS), a highly soluble fiber material, from agricultural waste streams, at an advantaged cost level relative to similar existing ingredients. The scope of the project includes pilot-scale process development (Task 1), compositional analysis (Task 2), and techno-economic analysis (Task 3).

40 CFR 66.81 - Final action.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 15 2010-07-01 2010-07-01 false Final action. 66.81 Section 66.81... COLLECTION OF NONCOMPLIANCE PENALTIES BY EPA Final Action § 66.81 Final action. (a) A final Agency action... State action pursuant to part 67. (b) The actions listed in paragraph (a) of this section constitute...

40 CFR 61.134 - Standard: Naphthalene processing, final coolers, and final-cooler cooling towers.

Code of Federal Regulations, 2012 CFR

2012-07-01

... POLLUTANTS National Emission Standard for Benzene Emissions from Coke By-Product Recovery Plants § 61.134... are allowed from naphthalene processing, final coolers and final-cooler cooling towers at coke by...

40 CFR 61.134 - Standard: Naphthalene processing, final coolers, and final-cooler cooling towers.

Code of Federal Regulations, 2014 CFR

2014-07-01

... POLLUTANTS National Emission Standard for Benzene Emissions from Coke By-Product Recovery Plants § 61.134... are allowed from naphthalene processing, final coolers and final-cooler cooling towers at coke by...

40 CFR 61.134 - Standard: Naphthalene processing, final coolers, and final-cooler cooling towers.

Code of Federal Regulations, 2013 CFR

2013-07-01

... POLLUTANTS National Emission Standard for Benzene Emissions from Coke By-Product Recovery Plants § 61.134... are allowed from naphthalene processing, final coolers and final-cooler cooling towers at coke by...

40 CFR 61.134 - Standard: Naphthalene processing, final coolers, and final-cooler cooling towers.

Code of Federal Regulations, 2011 CFR

2011-07-01

... POLLUTANTS National Emission Standard for Benzene Emissions from Coke By-Product Recovery Plants § 61.134... are allowed from naphthalene processing, final coolers and final-cooler cooling towers at coke by...

NREL Quickens its Tech Transfer Efforts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lammers, H.

2012-02-01

patent portfolio, often companies are looking to do more than just license a technology. These relationships are invaluable in successfully moving technologies from NREL to the marketplace. 'We may generate new and potentially valuable innovations, but our commercialization partners do the heavy work of building a successful business around our technology,' Farris said. Tools such as CRADAs (Cooperative Research and Development Agreements) allow NREL to continue working with companies to refine and develop technologies. And, working with businesses is an area where NREL excels. NREL is responsible for one quarter of the CRADAs in the DOE system. 'When you look at the results of our CRADA program, you can demonstrate that we are actively engaged with companies in collaborating on research and moving technologies to market,' Farris said. NREL is first among DOE labs with 186 active CRADAs. And last year, NREL also was first with the number of new CRADAs signed. 'Part of the success in our working with industry goes back to NREL's mission to grow and support new industries,' Farris added. 'NREL has basic research capabilities, but we are never going to be the ultimate producer of a commercial product. That is the role of the private sector.' Farris also credits the advocacy and support that the Office of Energy Efficiency and Renewable Energy at DOE provides for these technology transfer activities. 'EERE's support is critical to our success,' Farris said. To assist the private sector in moving a technology from the lab to the manufacturing line, NREL has a number of programs in place to give that first, or even final, nudge toward commercialization. For instance, the Commercialization Assistance Program helps startups overcome technical barriers by granting free access to 40 hours of work at the lab. Through the Innovation and Entrepreneurship Center, NREL also helps clean energy businesses develop strong links with the financial community, as well as other key

40 CFR 61.134 - Standard: Naphthalene processing, final coolers, and final-cooler cooling towers.

Code of Federal Regulations, 2010 CFR

2010-07-01

... POLLUTANTS National Emission Standard for Benzene Emissions from Coke By-Product Recovery Plants § 61.134... are allowed from naphthalene processing, final coolers and final-cooler cooling towers at coke by-product recovery plants. ...

Active matrix organic light emitting diode (AMOLED) performance and life test results

NASA Astrophysics Data System (ADS)

Fellowes, David A.; Wood, Michael V.; Hastings, Arthur R., Jr.; Draper, Russell S.; Lum, Alden K.; Ghosh, Amalkumar P.; Prache, Olivier; Wacyk, Ihor

2010-04-01

The US Army and eMagin Corporation established a Cooperative Research and Development Agreement (CRADA) to characterize the ongoing improvements in the lifetime of OLED displays. This CRADA also called for the evaluation of OLED performance as the need arises, especially when new products are developed or when a previously untested parameter needs to be understood. In 2006, eMagin Corporation developed long-life OLED-XLTM devices for use in their AMOLED microdisplays for head-worn applications. Through Research and Development programs from 2007 to 2009 with the US Government, eMagin made additional improvements in OLED life and developed the first SXGA (1280 × 1024 triad pixels) OLED microdisplay. US Army RDECOM CERDEC NVESD conducted life and performance tests on these displays, publishing results at the 2007, 2008, and 2009 SPIE Defense and Security Symposia1,2,3. Life and performance tests have continued through 2009, and this data will be presented along with a recap of previous data. This should result in a better understanding of the applicability of AMOLEDs in military and commercial head mounted systems: where good fits are made, and where further development might be desirable.

Active matrix organic light emitting diode (AMOLED)-XL performance and life test results

NASA Astrophysics Data System (ADS)

Fellowes, David A.; Wood, Michael V.; Hastings, Arthur R., Jr.; Draper, Russell S.; Lum, Alden K.; Ghosh, Amalkumar P.; Prache, Olivier; Wacyk, Ihor

2009-05-01

The US Army and eMagin Corporation established a Cooperative Research and Development Agreement (CRADA) to characterize the ongoing improvements in the lifetime of OLED displays. This CRADA also called for the evaluation of OLED performance as the need arises, especially when new products are developed or when a previously untested parameter needs to be understood. In 2006, eMagin Corporation developed long-life OLED-XL devices for use in their AMOLED microdisplays for head-worn applications. RDECOM CERDEC NVESD conducted life tests on these displays, finding over 200% lifetime improvement for the OLED-XL devices over the standard OLED displays, publishing results at the 2007 and 2008 SPIE Defense and Security Symposia1,2. In 2008, eMagin Corporation made additional improvements on the lifetime of their displays and developed the first SXGA (1280 × 1024 triad pixels) OLED microdisplay. A summary of the life and performance tests run at CERDEC NVESD will be presented along with a recap of previous data. This should result in a better understanding of the applicability of AMOLEDs in military and commercial head mounted systems: where good fits are made, and where further development might be desirable.

The NOAA Big Data Project

NASA Astrophysics Data System (ADS)

de la Beaujardiere, J.

2015-12-01

The US National Oceanic and Atmospheric Administration (NOAA) is a Big Data producer, generating tens of terabytes per day from hundreds of sensors on satellites, radars, aircraft, ships, and buoys, and from numerical models. These data are of critical importance and value for NOAA's mission to understand and predict changes in climate, weather, oceans, and coasts. In order to facilitate extracting additional value from this information, NOAA has established Cooperative Research and Development Agreements (CRADAs) with five Infrastructure-as-a-Service (IaaS) providers — Amazon, Google, IBM, Microsoft, Open Cloud Consortium — to determine whether hosting NOAA data in publicly-accessible Clouds alongside on-demand computational capability stimulates the creation of new value-added products and services and lines of business based on the data, and if the revenue generated by these new applications can support the costs of data transmission and hosting. Each IaaS provider is the anchor of a "Data Alliance" which organizations or entrepreneurs can join to develop and test new business or research avenues. This presentation will report on progress and lessons learned during the first 6 months of the 3-year CRADAs.

Active matrix organic light-emitting diode (AMOLED) performance and life test results

NASA Astrophysics Data System (ADS)

Fellowes, David A.; Wood, Michael V.; Hastings, Arthur R., Jr.; Draper, Russell S.; Ghosh, Amalkumar; Prache, Olivier; Wacyk, Ihor; Ali, Tariq; Khayrullin, Ilyas

2011-06-01

The US Army and eMagin Corporation established a Cooperative Research and Development Agreement (CRADA) to characterize the ongoing improvements in the lifetime of OLED displays. This CRADA also called for the evaluation of OLED performance as the need arises, especially when new products are developed or when a previously untested parameter needs to be understood. In 2006, eMagin Corporation developed long-life OLED-XL devices for use in their AMOLED microdisplays for head-worn applications. Through research and development programs from 2007 to 2010 with the US Government, eMagin made additional improvements in OLED life and developed the first SXGA (1280 X 1024 triad pixels) OLED microdisplay. US Army RDECOM CERDEC NVESD conducted life and performance tests on these displays, publishing results at the 2007, 2008, 2009, and 2010 SPIE Defense and Security Symposia1,2,3,4. Life and performance tests have continued through 2010, and this data will be presented along with a recap of previous data. This should result in a better understanding of the applicability of AMOLEDs in military and commercial head mounted systems: where good fits are made, and where further development might be desirable.

Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

DeTar, Carleton

This document constitutes the Final Report for award DE-FC02-06ER41446 as required by the Office of Science. It summarizes accomplishments and provides copies of scientific publications with significant contribution from this award.

Remote sensing estimation of colored dissolved organic matter (CDOM) in optically shallow waters

NASA Astrophysics Data System (ADS)

Li, Jiwei; Yu, Qian; Tian, Yong Q.; Becker, Brian L.

2017-06-01

It is not well understood how bottom reflectance of optically shallow waters affects the algorithm performance of colored dissolved organic matters (CDOM) retrieval. This study proposes a new algorithm that considers bottom reflectance in estimating CDOM absorption from optically shallow inland or coastal waters. The field sampling was conducted during four research cruises within the Saginaw River, Kawkawlin River and Saginaw Bay of Lake Huron. A stratified field sampling campaign collected water samples, determined the depth at each sampling location and measured optical properties. The sampled CDOM absorption at 440 nm broadly ranged from 0.12 to 8.46 m-1. Field sample analysis revealed that bottom reflectance does significantly change water apparent optical properties. We developed a CDOM retrieval algorithm (Shallow water Bio-Optical Properties algorithm, SBOP) that effectively reduces uncertainty by considering bottom reflectance in shallow waters. By incorporating the bottom contribution in upwelling radiances, the SBOP algorithm was able to explain 74% of the variance of CDOM values (RMSE = 0.22 and R2 = 0.74). The bottom effect index (BEI) was introduced to efficiently separate optically shallow and optically deep waters. Based on the BEI, an adaptive approach was proposed that references the amount of bottom effect in order to identify the most suitable algorithm (optically shallow water algorithm [SBOP] or optically deep water algorithm [QAA-CDOM]) to improve CDOM estimation (RMSE = 0.22 and R2 = 0.81). Our results potentially help to advance the capability of remote sensing in monitoring carbon pools at the land-water interface.

NRL Fact Book

DTIC Science & Technology

2002-11-01

CRADAs) under which NRL scientists and engineers work together with industry , academia, state or local governments, or other Federal agencies to... industrial hygiene, and environ- mental safety. The Division provides engineering and technical assistance to research divisions in the installation...The NRL Women in Science and Engineer - ing (WISE) Network is an open-membership network group of scientists and engineers who meet periodically to

A Comparison of Approaches for Solving Hard Graph-Theoretic Problems

DTIC Science & Technology

2015-05-01

collaborative effort “ Adiabatic Quantum Computing Applications Research” (14-RI-CRADA-02) between the Information Directorate and Lock- 3 Algorithm 3...using Matlab, a quantum annealing approach using the D-Wave computer , and lastly using satisfiability modulo theory (SMT) and corresponding SMT...methods are explored and consist of a parallel computing approach using Matlab, a quantum annealing approach using the D-Wave computer , and lastly using

Survey of Laboratories and Implementation of the Federal Defense Laboratory Diversification Program. Annex B. Department of the Navy Domestic Technology Transfer

DTIC Science & Technology

1993-10-01

received on a periodic basis that is the equivalent of a royalty. By that CRADA, a hybridoma producing an antibody useful in analytic...played an active role are: ( a ) The Annual High Tech Conference for Small Business sponsored by the New Jersey Commission on Science and Technology. 39...legally required. The new administration has made DTT a high priority, resulting in an increase in DTT

Penetrating Neurotrauma: What the Radiologists Needs to Know

DTIC Science & Technology

2017-04-22

Education (GHSE) (SG5 O&M): SG5 R&D: Tri-Service Nursing Research Program (TSNRP): Defense Medical Research & Development Program (DMRDP): NIH...RESTRICTIONS FOR PUBLICATION OR PRESENTATION THROUGH A COLLABORATIVE RESEARCH AND DEVELOPMENT AGREEMENT (CRADA), MATERIAL TRANSFER AGREEMENT (MTA...INTELLECTUAL PROPERTY RIGHTS AGREEMENT ETC.? O YES t8J NO NOTE: If the answer is YES then attach a copy of the Agreement lo the Publications

Evaluation of Anti-fouling Materials for Optical Sensors

DTIC Science & Technology

1997-09-30

were made using environmental scanning electron microscopy (ESEM). WORK COMPLETED A Cooperative Research and Development Agreement (CRADA) was...established between NRL and Magellan Co., Inc. (1051 Planter Place, Mt. Pleasant, SC) including a no-cost procurement of test coupons coated with chemical...acid-producing (103–104), facultative (102–103) and aerobic bacteria (>104) per ml sample, in addition to a heavy diatom population. Glass slides

76 FR 54525 - Notice of Availability of a Final Environmental Assessment (Final EA) and a Finding of No...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-01

... Environmental Assessment (Final EA) and a Finding of No Significant Impact (FONSI)/Record of Decision (ROD) for... Environmental Assessment (Final EA) and Finding of No Significant Impact (FONSI)/Record of Decision (ROD) for a...)/Record of Decision (ROD) based on the Final Environmental Assessment (Final EA) for a Proposed Airport...

FAA (Federal Aviation Administration) Air Traffic Activity FY 1985.

DTIC Science & Technology

1985-09-30

1009C4 7538 ’ TEXARKANA (TXK) N ., ITINERANT OPERATIO.S 34754 14 6886 25979 1915 LUCAL OPLRATIONS 16612 14739 1873 TOTAL OPLRATIONS 513b6 14 686...S 365 51622 TEXARKANA AN N 366 51366 SAGINAW TRI CITY MI 5 367 51248 TUSCA.UISA KIt. LV GVAF AL ’ 368 50924 IDANl FALLS rAI. NS FIELD IL N 369 50469 C...POCATELLO IL N 362 35079 ELMIRA NY N 363 34938 MOSLS LAKE GRANT WA N 364 34B50 * TEXARKANA AP N 365 34754 , DUBUQJE IA N 366 34488 TUSCALOOSA VAN GE GRAAF

Final Checks of Aquarius Instrument

NASA Image and Video Library

2011-04-29

Less than two months before launch, team members conduct their final checks of NASA Aquarius instrument at Vandenberg Air Force Base, Calif. Subsequent final instrument tests will be conducted on the launch pad.

Topical antifungal drug products for over-the-counter human use; amendment of final monograph. Final rule.

PubMed

2002-02-08

The Food and Drug Administration (FDA) is issuing a final rule amending the final monograph for over-the-counter (OTC) topical antifungal drug products to add the ingredient clotrimazole as generally recognized as safe and effective for the treatment of athlete's foot, jock itch, and ringworm. This final rule is part of FDA's ongoing review of OTC drug products.

29 CFR 1955.44 - Final decision.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 9 2010-07-01 2010-07-01 false Final decision. 1955.44 Section 1955.44 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED..., the Secretary shall issue a final decision ruling upon each exception and objection filed. The final...

Transition of NOAA's GPS-Met Data Acquisition and Processing System to the Commercial Sector: Inital Results

NASA Astrophysics Data System (ADS)

Jackson, Michael; Blatt, Stephan; Holub, Kirk

2015-04-01

In April of 2014, NOAA/OAR/ESRL Global Systems Division (GSD) and Trimble, in collaboration with Earth Networks, Inc. (ENI) signed a Cooperative Research and Development Agreement (CRADA) to transfer the existing NOAA GPS-Met Data Acquisition and Processing System (GPS-Met DAPS) technology to a commercial Trimble/ENI partnership. NOAA's GPS-Met DAPS is currently operated in a pseudo-operational mode but has proven highly reliable and running at over 95% uptime. The DAPS uses the GAMIT software to ingest dual frequency carrier phase GPS/GNSS observations and ancillary information such as real-time satellite orbits to estimate the zenith-scaled tropospheric (ZTD) signal delays and, where surface MET data are available, retrieve integrated precipitable water vapor (PWV). The NOAA data and products are made available to end users in near real-time. The Trimble/ENI partnership will use the Trimble Pivot™ software with the Atmosphere App to calculate zenith tropospheric (ZTD), tropospheric slant delay, and integrated precipitable water vapor (PWV). Evaluation of the Trimble software is underway starting with a comparison of ZTD and PWV values determined from four sub networks of GPS stations located 1. near NOAA Radiosonde Observation (Upper-Air Observation) launch sites; 2. Stations with low terrain/high moisture variability (Gulf Coast); 3. Stations with high terrain/low moisture variability (Southern California); and 4. Stations with high terrain/high moisture variability (high terrain variability elev. > 1000m). For each network GSD and T/ENI run the same stations for 30 days, compare results, and perform an evaluation of the long-term solution accuracy, precision and reliability. Metrics for success include T/ENI PWV estimates within 1.5 mm of ESRL/GSD's estimates 95% of the time (ZTD uncertainty of less than 10 mm 95% of the time). The threshold for allowable variations in ZTD between NOAA GPS-Met and T/ENI processing are 10mm. The CRADA 1&2 Trimble processing

48 CFR 32.605 - Final decisions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... REQUIREMENTS CONTRACT FINANCING Contract Debts 32.605 Final decisions. (a) The contracting officer shall issue a final decision as required by 33.211 if— (1) The contracting officer and the contractor are unable... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Final decisions. 32.605...

14 CFR 1214.1105 - Final ranking.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 5 2011-01-01 2010-01-01 true Final ranking. 1214.1105 Section 1214.1105 Aeronautics and Space NATIONAL AERONAUTICS AND SPACE ADMINISTRATION SPACE FLIGHT NASA Astronaut Candidate Recruitment and Selection Program § 1214.1105 Final ranking. Final rankings will be based on a combination of...

27 CFR 72.39 - Final action.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 2 2010-04-01 2010-04-01 false Final action. 72.39... Remission or Mitigation of Forfeitures § 72.39 Final action. (a) Petitions for remission or mitigation of forfeiture. (1) The Director shall take final action on any petition filed pursuant to these regulations...

27 CFR 72.39 - Final action.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 27 Alcohol, Tobacco Products and Firearms 2 2011-04-01 2011-04-01 false Final action. 72.39... Remission or Mitigation of Forfeitures § 72.39 Final action. (a) Petitions for remission or mitigation of forfeiture. (1) The Director shall take final action on any petition filed pursuant to these regulations...

Data breaches. Final rule.

PubMed

2008-04-11

This document adopts, without change, the interim final rule that was published in the Federal Register on June 22, 2007, addressing data breaches of sensitive personal information that is processed or maintained by the Department of Veterans Affairs (VA). This final rule implements certain provisions of the Veterans Benefits, Health Care, and Information Technology Act of 2006. The regulations prescribe the mechanisms for taking action in response to a data breach of sensitive personal information.

Cassini's Grand Finale Overview

NASA Astrophysics Data System (ADS)

Spilker, L. J.

2017-12-01

After 13 years in orbit, the Cassini-Huygens Mission to Saturn ended in a science-rich blaze of glory. Cassini sent back its final bits of unique science data on September 15, 2017, as it plunged into Saturn's atmosphere, vaporizing and satisfying planetary protection requirements. Cassini's final phase covered roughly ten months and ended with the first time exploration of the region between the rings and planet. In late 2016 Cassini transitioned to a series of 20 Ring Grazing orbits with peripases just outside Saturn's F ring, providing close flybys of tiny ring moons, including Pan, Daphnis and Atlas, and high-resolution views of Saturn's A and F rings. A final Titan flyby in late April 2017 propelled Cassini across Saturn's main rings and into its Grand Finale orbits. Comprised of 22 orbits, Cassini repeatedly dove between Saturn's innermost rings and upper atmosphere to answer fundamental questions unattainable earlier in the mission. The last orbit turned the spacecraft into the first Saturn atmosphere probe. The Grand Finale orbits provided highest resolution observations of both the rings and Saturn, and in-situ sampling of the ring particle composition, Saturn's atmosphere, plasma, and innermost radiation belts. The gravitational field was measured to unprecedented accuracy, providing information on the interior structure of the planet, winds in the deeper atmosphere, and mass of the rings. The magnetic field provided insight into the physical nature of the magnetic dynamo and structure of the internal magnetic field. The ion and neutral mass spectrometer sampled the upper atmosphere for molecules that escape the atmosphere in addition to molecules originating from the rings. The cosmic dust analyzer directly sampled the composition from different parts of the main rings for the first time. Fields and particles instruments directly measured the plasma environment between the rings and planet. Science highlights and new mysteries collected in the Grand

Public-Private Cooperation in the Department of Defense: A Framework for Analysis and Recommendations for Action (Defense Horizons, October 2012)

DTIC Science & Technology

2012-10-01

requirements de - fined by the public sector. CRADAs leverage private sector resources and knowledge to meet the needs of government agencies at no financial...situations helps resolve barriers to cooperation. The evolution of CRA- DAs offers insight into how DOD can interact with multiple partners in a mutually...actions among multiple private power companies, the public sector (at Federal, state, local, and tribal levels), and third parties (hos- pitals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daily, William; Mondt, William

The purpose of this CRADA was to develop a useful and commercially viable version of ERT technology for use in the oil, mining, engineering, and geotechnical industries. The goals required to accomplish these tasks included (1) developing commercial-grade data-acquisition systems and data analysis software, and (2) completing transfer of the state-of-the-art know-how, held by LLNL scientists and engineers, to personnel at RIMtech, Inc.

76 FR 76637 - Drawbridge Operation Regulation; Saginaw River, Bay City, MI

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-08

... April 15 and November 1, and generally increases on the weekends. Vehicular traffic has been reduced in..., including reduced vehicular traffic on weekends when recreational vessel traffic increases. Under the... drawbridge regulation was developed to reflect the current conditions and needs of both vessel and vehicular...

M-DAS: System for multispectral data analysis. [in Saginaw Bay, Michigan

NASA Technical Reports Server (NTRS)

Johnson, R. H.

1975-01-01

M-DAS is a ground data processing system designed for analysis of multispectral data. M-DAS operates on multispectral data from LANDSAT, S-192, M2S and other sources in CCT form. Interactive training by operator-investigators using a variable cursor on a color display was used to derive optimum processing coefficients and data on cluster separability. An advanced multivariate normal-maximum likelihood processing algorithm was used to produce output in various formats: color-coded film images, geometrically corrected map overlays, moving displays of scene sections, coverage tabulations and categorized CCTs. The analysis procedure for M-DAS involves three phases: (1) screening and training, (2) analysis of training data to compute performance predictions and processing coefficients, and (3) processing of multichannel input data into categorized results. Typical M-DAS applications involve iteration between each of these phases. A series of photographs of the M-DAS display are used to illustrate M-DAS operation.

Development of Carbon-14 Waste Destruction and Recovery System Using AC Plasma Torch Technology Final Report CRADA No. TC02108.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Althouse, P.; McKannay, R. H.

This was a collaborative effort between Lawrence Livermore National Security, LLC as manager and operator of Lawrence Livermore National Laboratory (LLNL) and ISOFLEX USA (ISOFLEX), to 1) develop and test a prototype waste destruction system ("System") using AC plasma torch technology to break down and drastically reduce the volume of Carbon-14 (C-14) contaminated medical laboratory wastes while satisfying all environmental regulations, and 2) develop and demonstrate methods for recovering 99%+ of the carbon including the C-14 allowing for possible re-use as a tagging and labeling tool in the biomedical industry.

Biomass Pyrolysis to Hydrocarbon Fuels in the Petroleum Refining Context: Cooperative Research and Development Final Report, CRADA Number CRD-12-500

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chum, Helena L.

This work focuses on developing a thermochemical route to produce biofuels from agricultural wastes such as sugar cane bagasse, wood chips or corn stover; more specifically it intends to develop the biomass pyrolysis route, which produces bio-oils. Production of bio-oils by pyrolysis is a commercial technology. However, bio-oils are currently not being used for liquid fuels production. Although bio-oils can be produced by high-pressure liquefaction, pyrolysis is a less expensive technology. Nevertheless, bio-oils cannot be used directly as a transportation fuel without upgrading, since they are generally unstable, viscous, and acidic. Thus NREL and Petrobras intend to use their combinedmore » expertise to develop a two-step route to biofuels production: in the first step, a stable bio-oil is produced by NREL biomass pyrolysis technology, while in the second step it is upgraded by using two distinct catalytic processes under development by Petrobras. The first process converts bio-oil into gasoline, LPG, and fuel oil using the catalytic cracking process, while the second one, converts bio-oil into synthesis gas. Syngas gasification catalysts provided by both NREL and Petrobras will be tested. The work includes experiments at both sites to produce bio-oil and then biofuels, life-cycle analysis of each route, personnel training and development of analytical methods with a duration time of two years.« less

Development of an Industry Dynamometer/Spin Test Facility--Equipment Only: Cooperative Research and Development Final Report, CRADA Number CRD-05-164

DOE Office of Scientific and Technical Information (OSTI.GOV)

McDade, Mark

2016-12-01

The Department of Energy/National Renewable Energy Laboratory (DOE/NREL) owns and operates a megawatt-scale dynamometer used for testing wind turbine drive trains up to 1.5 megawatt (MW) in rated capacity. At this time, this unit is the only unit of its type in the United States, available for use by the American Wind Industry. Currently this dynamometer is heavily backlogged and unavailable to provide testing needed by various wind industry members. DOE/NREL is in possession of two critical pieces of equipment that may be used to develop an alternative Dynamometer facility, but does not have the funds or other resources necessarymore » to develop such a facility. The Participant possesses complimentary facilities and infrastructure that when combined with the NREL equipment can create such a test facility. The Participant is also committed to expending funds to develop and operate such a facility to the subsequent benefit of the Wind Industry and DOE Wind Energy program. In exchange for DOE/NREL providing the critical equipment, the Participant will grant DOE/NREL a minimum of 90 days of testing time per year in the new facility while incurring no facilities fees.« less

Solar Resource Measurements in 1400 JR Lynch Street, Jackson, Mississippi: Cooperative Research and Development Final Report, CRADA Number CRD-07-254

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stoffel, Tom

Site-specific, long-term, continuous, and high-resolution measurements of solar irradiance are important for developing renewable resource data. These data are used for several research and development activities consistent with the NREL mission: Equipment will be used by Jackson State University for solar radiation data monitoring. This is a continuing effort of the Historically Black Colleges and Universities Solar Measurement Network; Provide high quality ground-truth data for satellite remote sensing validation; Support development of radiative transfer models for estimating solar irradiance from available meteorological observations; Provide solar resource information needed for technology deployment and operations. Data acquired under this agreement will bemore » available to the public through NREL's Measurement & Instrumentation Data Center (MIDC) (www.nrel.gov/midc) or the Renewable Resource Data Center (RReDC ) (http://rredc.nrel.gov). The MIDC offers a variety of standard data display, access, and analysis tools designed to address the needs of a wide user audience (e.g., industry, academia, and government interests.« less

Portfolio-Scale Optimization of Customer Energy Efficiency Incentive and Marketing: Cooperative Research and Development Final Report, CRADA Number CRD-13-535

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brackney, Larry J.

North East utility National Grid (NGrid) is developing a portfolio-scale application of OpenStudio designed to optimize incentive and marketing expenditures for their energy efficiency (EE) programs. NGrid wishes to leverage a combination of geographic information systems (GIS), public records, customer data, and content from the Building Component Library (BCL) to form a JavaScript Object Notation (JSON) input file that is consumed by an OpenStudio-based expert system for automated model generation. A baseline model for each customer building will be automatically tuned using electricity and gas consumption data, and a set of energy conservation measures (ECMs) associated with each NGrid incentivemore » program will be applied to the model. The simulated energy performance and return on investment (ROI) will be compared with customer hurdle rates and available incentives to A) optimize the incentive required to overcome the customer hurdle rate and B) determine if marketing activity associated with the specific ECM is warranted for that particular customer. Repeated across their portfolio, this process will enable NGrid to substantially optimize their marketing and incentive expenditures, targeting those customers that will likely adopt and benefit from specific EE programs.« less

Geysers advanced direct contact condenser research

DOE Office of Scientific and Technical Information (OSTI.GOV)

Henderson, J.; Bahning, T.; Bharathan, D.

1997-12-31

The first geothermal application of the Advanced Direct Contact Condenser (ADCC) technology developed by the National Renewable Energy Laboratory (NREL) is now operational and is being tested at The Geysers Power Plant Unit 11. This major research effort is being supported through the combined efforts of NREL, The Department of Energy (DOE), and Pacific Gas and Electric (PG&E). NREL and PG&E have entered into a Cooperative Research And Development Agreement (CRADA) for a project to improve the direct-contact condenser performance at The Geysers Power Plant. This project is the first geothermal adaptation of an advanced condenser design developed for themore » Ocean Thermal Energy Conversion (OTEC) systems. PG&E expects this technology to improve power plant performance and to help extend the life of the steam field by using steam more efficiently. In accordance with the CRADA, no money is transferred between the contracting parties. In this case the Department of Energy is funding NREL for their efforts in this project and PG&E is contributing funds in kind. Successful application of this technology at The Geysers will provide a basis for NREL to continue to develop this technology for other geothermal and fossil power plant systems.« less

Active matrix organic light emitting diode (AMOLED) performance and life test results

NASA Astrophysics Data System (ADS)

Fellowes, David A.; Botkin, Michael E.; Draper, Russell S.; Coletta, Jason

2013-05-01

The U.S. Army and eMagin Corporation established a Cooperative Research and Development Agreement (CRADA) to characterize the ongoing improvements in the lifetime of OLED displays. This CRADA also called for the evaluation of OLED performance as the need arises, especially when new products are developed or when a previously untested parameter needs to be understood. In 2006, eMagin Corporation developed long-life OLED-XL devices for use in their AMOLED microdisplays for head-worn applications. Through Research and Development programs from 2007 to 2012 with the U.S. Government, eMagin made additional improvements in OLED life and developed the first SXGA (1280 X 1024 with triad pixels) and WUXGA (1920 X 1200 with triad pixels) OLED microdisplays. US Army RDECOM CERDEC NVESD conducted life and performance tests on these displays, publishing results at the 2012, 2011, 2010, 2009, 2008, and 2007 SPIE Defense, Security and Sensing Symposia. Life and performance tests have continued through 2013, and this data will be presented along with a comparison to previous data. This should result in a better understanding of the applicability of AMOLEDs in military and commercial head mounted systems, where good fits are made, and where further development might be desirable.

Active matrix organic light emitting diode (AMOLED) performance and life test results

NASA Astrophysics Data System (ADS)

Fellowes, David A.; Wood, Michael V.; Hastings, Arthur R., Jr.; Draper, Russell S.; Ghosh, Amalkumar; Prache, Olivier; Wacyk, Ihor

2012-06-01

The US Army and eMagin Corporation established a Cooperative Research and Development Agreement (CRADA) to characterize the ongoing improvements in the lifetime of OLED displays. This CRADA also called for the evaluation of OLED performance as the need arises, especially when new products are developed or when a previously untested parameter needs to be understood. In 2006, eMagin Corporation developed long-life OLED-XL devices for use in their AMOLED microdisplays for head-worn applications. Through Research and Development programs from 2007 to 2011 with the US Government, eMagin made additional improvements in OLED life and developed the first SXGA (1280 X 1024 triad pixels) and WUXGA (1920 X 1200) OLED microdisplays. US Army RDECOM CERDEC NVESD conducted life and performance tests on these displays, publishing results at the 2011, 2010, 2009, 2008, and 2007 SPIE Defense, Security and Sensing Symposia1,2,3,4,5. Life and performance tests have continued through 2012, and this data will be presented along with a recap of previous data. This should result in a better understanding of the applicability of AMOLEDs in military and commercial head mounted systems by determining where good fits are made and where further development might be desirable.

76 FR 65746 - Notice of Availability of Joint Final Environmental Impact Statement/Final Environmental Impact...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-24

... Boulevard. The project will consist of up to 128 wind turbines (1.5 to 3.0 MW each) with a generating... Statement/Final Environmental Impact Report for the Tule Wind Project, California, and Notice of Intent To... Final Environmental Impact Report (EIR) as a joint environmental analysis document for Tule Wind, LLC's...

14 CFR 1214.1105 - Final ranking.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Recruitment and Selection Program § 1214.1105 Final ranking. Final rankings will be based on a combination of the selection board's initial evaluations and the results of the interview process. Veteran's...

49 CFR 98.11 - Final administrative decision.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 1 2010-10-01 2010-10-01 false Final administrative decision. 98.11 Section 98.11 Transportation Office of the Secretary of Transportation ENFORCEMENT OF RESTRICTIONS ON POST-EMPLOYMENT ACTIVITIES Administration of Enforcement Proceedings § 98.11 Final administrative decision. The final...

Use of remote sensing for land use policy formulation

NASA Technical Reports Server (NTRS)

1982-01-01

Research projects described include: (1) identifying coniferous forest types in Michigan using LANDSAT imagery; (2) investigating synoptic temperature patterns in Michigan as determined via GOES and HCMM thermal imagery; (3) land surface change detection using satellite data and a geographic data base; (4) determining soil map unit composition by electronic scanning densitometry; and (5) delimiting areas of virus infection in vineyards and blueberry fields in southwestern and western Michigan. Contractual activities involve important farmlands inventory, changes in aquatic vegetation in Saginaw Bay, digitized soil association map of Michigan, and aerial photography for hybrid-poplar research. On-going projects are also being conducted in Jamaica, Honduras, the Dominican Republic and Kenya.

Department of Defense Base Structure Report (A Summary of DoD’s Real Property Inventory) Fiscal Year 2006 Baseline

DTIC Science & Technology

2006-01-01

438 1,964,339 7,6767,117 762.7 28 0 0Navy Active NMCRC Miami Miami 2 62,752 2017 10.7 1,215 2 0Navy Reserve NS Mayport FL Mayport 646 3,822,934 16...3,746 724403 17.8AF Active Lone Star AAP Texarkana 876 3,264,503 15,69915,699 841.3 1 18 0Army Active C Lonestar Pecos Electronic Scoring Site Pecos 2...1,183.5 3,201 5,355 0AF Active R Red River Army Depot Texarkana 1,125 7,555,228 18 173,594 18,31618,316 1,558.5 144 1,894 1,838Army Active R Saginaw

OPALS Final Testing

NASA Image and Video Library

2014-07-24

Optical PAyload for Lasercomm Science OPALS flight terminal undergoes final testing at NASA Jet Propulsion Laboratory. OPALS was launched to the International Space Station from Cape Canaveral Air Force Station in Florida on April 18, 2014.

10 CFR 603.890 - Final performance report.

Code of Federal Regulations, 2010 CFR

2010-01-01

... to Other Administrative Matters Financial and Programmatic Reporting § 603.890 Final performance report. A TIA must require a final performance report that addresses all major accomplishments under the... 10 Energy 4 2010-01-01 2010-01-01 false Final performance report. 603.890 Section 603.890 Energy...

44 CFR 9.12 - Final public notice.

Code of Federal Regulations, 2013 CFR

2013-10-01

... public with a statement of its final decision and shall explain the relevant factors considered by the... provided the final notice. (b) For actions for which an environmental impact statement is being prepared... environmental assessment was prepared, the Notice of No Significant Impact is adequate to constitute final...

44 CFR 9.12 - Final public notice.

Code of Federal Regulations, 2012 CFR

2012-10-01

... public with a statement of its final decision and shall explain the relevant factors considered by the... provided the final notice. (b) For actions for which an environmental impact statement is being prepared... environmental assessment was prepared, the Notice of No Significant Impact is adequate to constitute final...

Natick Soldier Systems Center Science and Technology Board (9th)

DTIC Science & Technology

2012-05-29

NSRDEC overarching CRADA’s with all five UMass campuses (in routing) • Patent License Agreement with Niche, Inc , New Bedford, MA (Ground impact...84.2 1 201 1 2014 GEAR4 UNITY REMOTE (Ben created.’deveil)j)ild~icensed) 2017 :>O?O SUM DEVICES QUANTIFIED SELF JAWBONE UP ATBIT ULTRA NIKE FUEL...Rudolph gained system development experience in multiple IT companies. In March 1994, he co-founded Paradigm Technologies, Inc ., an industry partner

CERDEC Fuel Cell Team: Military Transitions for Soldier Fuel Cells

DTIC Science & Technology

2008-10-27

Fuel Cell (DMFC) (PEO Soldier) Samsung: 20W DMFC (CRADA) General Atomics & Jadoo: 50W Ammonia Borane Fueled PEMFC Current Fuel Cell Team Efforts...Continued Ardica: 20W Wearable PEMFC operating on Chemical Hydrides Spectrum Brands w/ Rayovac: Hydrogen Generators and Alkaline Fuel Cells for AA...100W Ammonia Borane fueled PEMFC Ultralife: 150W sodium borohydride fueled PEMFC Protonex: 250W RMFC and Power Manager (ARO) NanoDynamics: 250W SOFC

Develop Roll-to-Roll Manufacturing Process of ZrO 2 Nanocrystals/Acrylic Nanocomposites for High Refractive Index Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Joshi, Pooran C.; Compton, Brett G.; Li, Jianlin

2015-04-01

The purpose of this Cooperative Research and Development Agreement (CRADA) was to develop and evaluate ZrO 2/acrylic nanocomposite coatings for integrated optoelectronic applications. The formulations engineered to be compatible with roll-to-roll process were evaluated in terms of optical and dielectric properties. The uniform distribution of the ZrO 2 nanocrystals in the polymer matrix resulted in highly tunable refractive index and dielectric response suitable for advanced photonic and electronic device applications.

OPALS Final Inspection

NASA Image and Video Library

2014-07-24

The Optical PAyload for Lasercomm Science OPALS undergoes final inspection prior to shipment to NASA Kennedy Space Center. OPALS was launched to the International Space Station from Cape Canaveral Air Force Station in Florida on April 18, 2014.

48 CFR 1552.211-77 - Final reports.

Code of Federal Regulations, 2013 CFR

2013-10-01

... reports. As prescribed in 1511.011-77, insert this contract clause when a contract requires both a draft and a final report. FINAL REPORTS (SEP 2013) (a) “Draft Report”__The Contractor shall submit to the Contracting Officer's Representative __ copies of the draft final report on or before ___ (date) __ The...

10 CFR 950.34 - Final claim determination.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Final claim determination. 950.34 Section 950.34 Energy DEPARTMENT OF ENERGY STANDBY SUPPORT FOR CERTAIN NUCLEAR PLANT DELAYS Dispute Resolution Process § 950.34 Final claim determination. (a) If the parties reach a Final Claim Determination through mediation, or...

10 CFR 950.34 - Final claim determination.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 4 2011-01-01 2011-01-01 false Final claim determination. 950.34 Section 950.34 Energy DEPARTMENT OF ENERGY STANDBY SUPPORT FOR CERTAIN NUCLEAR PLANT DELAYS Dispute Resolution Process § 950.34 Final claim determination. (a) If the parties reach a Final Claim Determination through mediation, or...

Cassini's Grand Finale Science Highlights

NASA Astrophysics Data System (ADS)

Spilker, Linda

2017-10-01

After 13 years in orbit, the Cassini-Huygens Mission to Saturn ended in a science-rich blaze of glory. Cassini returned its final bits of unique science data on September 15, 2017, as it plunged into Saturn's atmosphere satisfying planetary protection requirements. Cassini's Grand Finale covered a period of roughly five months and ended with the first time exploration of the region between the rings and planet.The final close flyby of Titan in late April 2017 propelled Cassini across Saturn’s main rings and into its Grand Finale orbits; 22 orbits that repeatedly dove between Saturn’s innermost rings and upper atmosphere making Cassini the first spacecraft to explore this region. The last orbit turned the spacecraft into the first Saturn upper atmospheric probe.The Grand Finale orbits provided highest resolution observations of both the rings and Saturn, and in-situ sampling of the ring particle composition, Saturn's atmosphere, plasma, and innermost radiation belts. The gravitational field was measured to unprecedented accuracy, providing information on the interior structure of the planet, winds in the deeper atmosphere, and mass of the rings. The magnetic field provided insight into the physical nature of the magnetic dynamo and structure of the internal magnetic field. The ion and neutral mass spectrometer sampled the upper atmosphere for molecules that escape the atmosphere in addition to molecules originating from the rings. The cosmic dust analyzer directly sampled the composition from different parts of the main rings for the first time. Fields and particles instruments directly measured the plasma environment between the rings and planet.Science highlights and new mysteries gleaned to date from the Grand Finale orbits will be discussed.The research described in this paper was carried out in part at the Jet Propulsion Laboratory, California Institute of Technology, under a contract with the National Aeronautics and Space Administration. Copyright 2017

Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stinis, Panos

2016-08-07

This is the final report for the work conducted at the University of Minnesota (during the period 12/01/12-09/18/14) by PI Panos Stinis as part of the "Collaboratory on Mathematics for Mesoscopic Modeling of Materials" (CM4). CM4 is a multi-institution DOE-funded project whose aim is to conduct basic and applied research in the emerging field of mesoscopic modeling of materials.

Probability of acoustic transmitter detections by receiver lines in Lake Huron: results of multi-year field tests and simulations

USGS Publications Warehouse

Hayden, Todd A.; Holbrook, Christopher M.; Binder, Thomas; Dettmers, John M.; Cooke, Steven J.; Vandergoot, Christopher S.; Krueger, Charles C.

2016-01-01

BackgroundAdvances in acoustic telemetry technology have led to an improved understanding of the spatial ecology of many freshwater and marine fish species. Understanding the performance of acoustic receivers is necessary to distinguish between tagged fish that may have been present but not detected and from those fish that were absent from the area. In this study, two stationary acoustic transmitters were deployed 250 m apart within each of four acoustic receiver lines each containing at least 10 receivers (i.e., eight acoustic transmitters) located in Saginaw Bay and central Lake Huron for nearly 2 years to determine whether the probability of detecting an acoustic transmission varied as a function of time (i.e., season), location, and distance between acoustic transmitter and receiver. Distances between acoustic transmitters and receivers ranged from 200 m to >10 km in each line. The daily observed probability of detecting an acoustic transmission was used in simulation models to estimate the probability of detecting a moving acoustic transmitter on a line of receivers.ResultsThe probability of detecting an acoustic transmitter on a receiver 1000 m away differed by month for different receiver lines in Lake Huron and Saginaw Bay but was similar for paired acoustic transmitters deployed 250 m apart within the same line. Mean probability of detecting an acoustic transmitter at 1000 m calculated over the study period varied among acoustic transmitters 250 m apart within a line and differed among receiver lines in Lake Huron and Saginaw Bay. The simulated probability of detecting a moving acoustic transmitter on a receiver line was characterized by short periods of time with decreased detection. Although increased receiver spacing and higher fish movement rates decreased simulated detection probability, the location of the simulated receiver line in Lake Huron had the strongest effect on simulated detection probability.ConclusionsPerformance of receiver

Relation between organic-wastewater compounds, groundwater geochemistry, and well characteristics for selected wells in Lansing, Michigan

USGS Publications Warehouse

Haack, Sheridan K.; Luukkonen, Carol L.

2013-01-01

In 2010, groundwater from 20 Lansing Board of Water and Light (BWL) production wells was tested for 69 organic-wastewater compounds (OWCs). The OWCs detected in one-half of the sampled wells are widely used in industrial and environmental applications and commonly occur in many wastes and stormwater. To identify factors that contribute to the occurrence of these constituents in BWL wells, the U.S. Geological Survey (USGS) interpreted the results of these analyses and related detections of OWCs to local characteristics and groundwater geochemistry. Analysis of groundwater-chemistry data collected by the BWL during routine monitoring from 1969 to 2011 indicates that the geochemistry of the BWL wells has changed over time, with the major difference being an increase in sodium and chloride. The concentrations of sodium and chloride were positively correlated to frequency of OWC detections. The BWL wells studied are all completed in the Saginaw aquifer, which consists of water-bearing sandstones of Pennsylvanian age. The Saginaw aquifer is underlain by the Parma-Bayport aquifer, and overlain by the Glacial aquifer. Two possible sources of sodium and chloride were evaluated: basin brines by way of the Parma-Bayport aquifer, and surficial sources by way of the Glacial aquifer. To determine if water from the underlying aquifer had influenced well-water geochemistry over time, the total dissolved solids concentration and changes in major ion concentrations were examined with respect to well depth, age, and pumping rate. To address a possible surficial source of sodium and chloride, 25 well, aquifer, or hydrologic characteristics, and 2 groundwater geochemistry variables that might influence whether, or the rate at which, water from the land surface could reach each well were compared to OWC detections and well chemistry. The statistical tests performed during this study, using available variables, indicated that reduced time of travel of water from the land surface to the

X-43A Final Flight Observations

NASA Technical Reports Server (NTRS)

Grindle, Laurie

2011-01-01

The presentation will provide an overview of the final flight of the NASA X-43A project. The project consisted of three flights, two planned for Mach 7 and one for Mach 10. The first flight, conducted on June 2, 2001, was unsuccessful and resulted in a nine-month mishap investigation. A two-year return to flight effort ensued and concluded when the second Mach 7 flight was successfully conducted on March 27, 2004. The third and final flight, which occurred on November 16, 2004, was the first Mach 10 flight demonstration of an airframe-integrated, scramjet-powered, hypersonic vehicle. As such, the final flight presented first time technical challenges in addition to final flight project closeout concerns. The goals and objectives for the third flight as well as those for the project will be presented. The configuration of the Hyper-X stack including the X-43A, Hyper-X launch vehicle, and Hyper-X research vehicle adapter wil also be presented. Mission differences, vehicle modifications and lessons learned from the first and second flights as they applied to the third flight will also be discussed. Although X-43A flight 3 was always planned to be the final flight of the X-43A project, the X-43 program had two other vehicles and corresponding flight phases in X-43C and X-43B. Those other projects never manifested under the X-43 banner and X-43A flight 3 also became the final flight of X-43 program.

17 CFR 8.20 - Final decision.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 17 Commodity and Securities Exchanges 1 2010-04-01 2010-04-01 false Final decision. 8.20 Section 8.20 Commodity and Securities Exchanges COMMODITY FUTURES TRADING COMMISSION EXCHANGE PROCEDURES FOR DISCIPLINARY, SUMMARY, AND MEMBERSHIP DENIAL ACTIONS Disciplinary Procedure § 8.20 Final decision. Each...

21 CFR 1315.62 - Final order.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 9 2011-04-01 2011-04-01 false Final order. 1315.62 Section 1315.62 Food and Drugs DRUG ENFORCEMENT ADMINISTRATION, DEPARTMENT OF JUSTICE IMPORTATION AND PRODUCTION QUOTAS FOR EPHEDRINE, PSEUDOEPHEDRINE, AND PHENYLPROPANOLAMINE Hearings § 1315.62 Final order. As soon as practicable...

21 CFR 1315.62 - Final order.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 9 2014-04-01 2014-04-01 false Final order. 1315.62 Section 1315.62 Food and Drugs DRUG ENFORCEMENT ADMINISTRATION, DEPARTMENT OF JUSTICE IMPORTATION AND PRODUCTION QUOTAS FOR EPHEDRINE, PSEUDOEPHEDRINE, AND PHENYLPROPANOLAMINE Hearings § 1315.62 Final order. As soon as practicable...

21 CFR 1315.62 - Final order.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 9 2012-04-01 2012-04-01 false Final order. 1315.62 Section 1315.62 Food and Drugs DRUG ENFORCEMENT ADMINISTRATION, DEPARTMENT OF JUSTICE IMPORTATION AND PRODUCTION QUOTAS FOR EPHEDRINE, PSEUDOEPHEDRINE, AND PHENYLPROPANOLAMINE Hearings § 1315.62 Final order. As soon as practicable...

21 CFR 1315.62 - Final order.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 9 2010-04-01 2010-04-01 false Final order. 1315.62 Section 1315.62 Food and Drugs DRUG ENFORCEMENT ADMINISTRATION, DEPARTMENT OF JUSTICE IMPORTATION AND PRODUCTION QUOTAS FOR EPHEDRINE, PSEUDOEPHEDRINE, AND PHENYLPROPANOLAMINE Hearings § 1315.62 Final order. As soon as practicable...

21 CFR 1315.62 - Final order.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 9 2013-04-01 2013-04-01 false Final order. 1315.62 Section 1315.62 Food and Drugs DRUG ENFORCEMENT ADMINISTRATION, DEPARTMENT OF JUSTICE IMPORTATION AND PRODUCTION QUOTAS FOR EPHEDRINE, PSEUDOEPHEDRINE, AND PHENYLPROPANOLAMINE Hearings § 1315.62 Final order. As soon as practicable...

17 CFR 8.28 - Final decision.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 17 Commodity and Securities Exchanges 1 2010-04-01 2010-04-01 false Final decision. 8.28 Section 8.28 Commodity and Securities Exchanges COMMODITY FUTURES TRADING COMMISSION EXCHANGE PROCEDURES FOR DISCIPLINARY, SUMMARY, AND MEMBERSHIP DENIAL ACTIONS Summary Actions § 8.28 Final decision. Each exchange shall...

50 CFR 296.11 - Final determination.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 50 Wildlife and Fisheries 7 2010-10-01 2010-10-01 false Final determination. 296.11 Section 296.11 Wildlife and Fisheries NATIONAL MARINE FISHERIES SERVICE, NATIONAL OCEANIC AND ATMOSPHERIC ADMINISTRATION, DEPARTMENT OF COMMERCE CONTINENTAL SHELF FISHERMEN'S CONTINGENCY FUND § 296.11 Final determination. (a) If a...

Aftertreatment Technologies for Off-Highway Heavy-Duty Diesel Engines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kass, M.D.

2008-07-15

The objective of this program was to explore a combination of advanced injection control and urea-selective catalytic reduction (SCR) to reduce the emissions of oxides of nitrogen (NOx) and particulate matter (PM) from a Tier 2 off-highway diesel engine to Tier 3 emission targets while maintaining fuel efficiency. The engine used in this investigation was a 2004 4.5L John Deere PowerTechTM; this engine was not equipped with exhaust gas recirculation (EGR). Under the original CRADA, the principal objective was to assess whether Tier 3 PM emission targets could be met solely by increasing the rail pressure. Although high rail pressuremore » will lower the total PM emissions, it has a contrary effect to raise NOx emissions. To address this effect, a urea-SCR system was used to determine whether the enhanced NOx levels, associated with high rail pressure, could be reduced to Tier 3 levels. A key attraction for this approach is that it eliminates the need for a Diesel particulate filter (DPF) to remove PM emissions. The original CRADA effort was also performed using No.2 Diesel fuel having a maximum sulfur level of 500 ppm. After a few years, the CRADA scope was expanded to include exploration of advanced injection strategies to improve catalyst regeneration and to explore the influence of urea-SCR on PM formation. During this period the emission targets also shifted to meeting more stringent Tier 4 emissions for NOx and PM, and the fuel type was changed to ultra-low sulfur Diesel (ULSD) having a maximum sulfur concentration of 15 ppm. New discoveries were made regarding PM formation at high rail pressures and the influences of oxidation catalysts and urea-SCR catalysts. These results are expected to provide a pathway for lower PM and NOx emissions for both off- and on-highway applications. Industrial in-kind support was available throughout the project period. Review of the research results were carried out on a regular basis (annual reports and meetings) followed by

Final June Revisions Rule Significant Contribution Assessment TSD

EPA Pesticide Factsheets

This Technical Support Document (TSD) presents quantitative assessments of the relationship between the final February revisions to the Transport Rule, the final June revisions rule, and the original analysis conducted for the final Transport Rule.

21 CFR 1316.67 - Final order.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 9 2010-04-01 2010-04-01 false Final order. 1316.67 Section 1316.67 Food and Drugs DRUG ENFORCEMENT ADMINISTRATION, DEPARTMENT OF JUSTICE ADMINISTRATIVE FUNCTIONS, PRACTICES, AND PROCEDURES Administrative Hearings § 1316.67 Final order. As soon as practicable after the presiding officer...

10 CFR 1707.206 - Final determination.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Final determination. 1707.206 Section 1707.206 Energy DEFENSE NUCLEAR FACILITIES SAFETY BOARD TESTIMONY BY DNFSB EMPLOYEES AND PRODUCTION OF OFFICIAL RECORDS IN LEGAL PROCEEDINGS Requests for Testimony and Production of Documents § 1707.206 Final determination. The...

10 CFR 1707.206 - Final determination.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 4 2012-01-01 2012-01-01 false Final determination. 1707.206 Section 1707.206 Energy DEFENSE NUCLEAR FACILITIES SAFETY BOARD TESTIMONY BY DNFSB EMPLOYEES AND PRODUCTION OF OFFICIAL RECORDS IN LEGAL PROCEEDINGS Requests for Testimony and Production of Documents § 1707.206 Final determination. The...

10 CFR 1707.206 - Final determination.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 4 2014-01-01 2014-01-01 false Final determination. 1707.206 Section 1707.206 Energy DEFENSE NUCLEAR FACILITIES SAFETY BOARD TESTIMONY BY DNFSB EMPLOYEES AND PRODUCTION OF OFFICIAL RECORDS IN LEGAL PROCEEDINGS Requests for Testimony and Production of Documents § 1707.206 Final determination. The...