Sample records for sago pith residue

  1. Two-steps microwave-assisted treatment on acid hydrolysis of sago pith for bioethanol production

    NASA Astrophysics Data System (ADS)

    Sunarti, T. C.; Yanti, S. D.; Ruriani, E.

    2017-05-01

    Sago is a genus of palm that can be utilized to produce fermentable sugars as substrate for bioethanol. Sago pith is a heterogeneous substrate consists of starch and fiber. Acid hydrolysis by microwave heating radiation can break down starch and fibers together in a very short time, so it is considered to be very efficient process. The use of microwave energy (as power level) and variation of heating time can produce fermentable sugar with certain characteristics. This study included the preparation and analysis of sago pith flour; process of acid hydrolysis (0.3 M and 0.5 M H2SO4) using two steps microwave heating, first with power level 30% (1, 2 and 3 min) and second with power level 70% (3 min); and ethanol production. The conventional treatment (autoclaving at 121°C for 15 min) was carried for the comparison. The highest fermentable sugar (105.7 g/l) was resulted from microwave heating with power level 30% for 2 min followed by the power level 70% for 3 min. This hydrolyzate then used as substrate for bioethanol fermentation and partially neutralized (pH 3, 4, 5) by using yeast Issatchenkia orientalis, and the highest ethanol (2.8 g/l) was produced in pH 5.

  2. Sago pondweed (Potamogeton pectinatus L.): A literature review

    USGS Publications Warehouse

    Kantrud, Harold A.

    1990-01-01

    Sago pondweed (Potamogeton pectinatus L.) is a submersed macrophyte of nearly cosmopolitan distribution. The plant is of worldwide importance as a waterfowl food but also can be a nuisance in irrigation canals and recreational areas. The plant reproduces by many different means, depending on habitat and environmental stress. Several genetic ecotypes have evolved. Most important as waterfowl food are the turions (tubers), vegetative propagules rich in carbohydrates that are mostly buried in bottom sediments. In temperate wetlands, most turions sprout in spring, making sago behave as an annual. Drupelets (seeds) are the sexual propagules of sago and provide a mechanism for sago to survive periods of drought and excessive water salinity. Drupelets can be washed ashore or carried by birds for long distances. Sago decomposes rapidly at senescence, annually in temperate wetlands.Sago is mostly found in semipermanently or permanently flooded mixosaline lacustrine, palustrine, and riverine wetlands < 2.5 m deep, where fetches are not large or currents are < 1 m/s. Sago seems to prefer stable water levels but can tolerate significant water level fluctuations. Among the Potamogetons, only sago tolerates high salinity, pH, and alkalinity, but it fares poorly among specialist taxa in acidic or nutrient-poor waters. Sago is highly tolerant of eutrophic waters, and it can be the only species of submersed macrophyte present in heavily polluted sites. Sago grows in nearly all bottom substrates. Turbidity is the factor that most frequently limits sago growth.Sago often occurs in monotypic stands but can grow with many other submersed and emergent macrophytes. Dominance by sago in certain wetlands sometimes alternates with dominance by other submersed macrophytes when salinities or other environmental factors change. Sago also can be associated with a large variety of unattached filamentous, planktonic, or epiphytic algae. Increased turbidity caused by planktonic algae often is

  3. 21 CFR 133.186 - Sap sago cheese.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 2 2013-04-01 2013-04-01 false Sap sago cheese. 133.186 Section 133.186 Food and... Products § 133.186 Sap sago cheese. (a) Description. (1) Sap sago cheese is the food prepared by the... method described in § 133.5. Sap sago cheese is not less than 5 months old. (2) One or more of the dairy...

  4. 21 CFR 133.186 - Sap sago cheese.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Sap sago cheese. 133.186 Section 133.186 Food and... CONSUMPTION CHEESES AND RELATED CHEESE PRODUCTS Requirements for Specific Standardized Cheese and Related Products § 133.186 Sap sago cheese. (a) Description. (1) Sap sago cheese is the food prepared by the...

  5. 21 CFR 133.186 - Sap sago cheese.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 2 2011-04-01 2011-04-01 false Sap sago cheese. 133.186 Section 133.186 Food and... CONSUMPTION CHEESES AND RELATED CHEESE PRODUCTS Requirements for Specific Standardized Cheese and Related Products § 133.186 Sap sago cheese. (a) Description. (1) Sap sago cheese is the food prepared by the...

  6. Drying kinetics and mathematical modeling of hot air drying of coconut coir pith.

    PubMed

    Fernando, J A K M; Amarasinghe, A D U S

    2016-01-01

    Drying kinetics of coir pith was studied and the properties of compressed coir pith discs were analyzed. Coir pith particles were oven dried in the range of temperatures from 100 to 240 °C and the rehydration ability of compressed coir pith was evaluated by finding the volume expansion. The optimum drying temperature was found to be 140 °C. Hot air drying was carried out to examine the drying kinetics by allowing the coir pith particles to fluidize and circulate inside the drying chamber. Particle motion within the drying chamber closely resembled the particle motion in a flash dryer. The effective moisture diffusivity was found to increase from 1.18 × 10(-8) to 1.37 × 10(-8) m(2)/s with the increase of air velocity from 1.4 to 2.5 m/s respectively. Correlation analysis and residual plots were used to determine the adequacy of existing mathematical models for describing the drying behavior of coir pith. The empirical models, Wang and Singh model and Linear model, were found to be adequate for accurate prediction of drying behavior of coir pith. A new model was proposed by modifying the Wang and Singh model and considering the effect of air velocity. It gave the best correlation between observed and predicted moisture ratio with high value of coefficient of determination (R(2)) and lower values of root mean square error, reduced Chi square (χ(2)) and mean relative deviation (E%).

  7. The Utilization of Sago Waste as Cattle Feed

    NASA Astrophysics Data System (ADS)

    Tiro, B. M. W.; Beding, P. A.; Baliadi, Y.

    2018-02-01

    This study aimed was to evaluate nutrition value of sago waste and its effect on cattle performance.The collected data were analyzed using analysis of variance. The results of the study showed that of the utilization of sago waste had a positive effect on average daily gain (ADG), where with 2% sago waste of body weight (P2 treatment) gave the highest ADG 0.43 ± 0.02 kg/h/day and cattle which consumed only forage without sago waste (P0) gave the lowest ADG 0.26 ± 0.04 kg/h/day. Statistical analysis showed that the addition of sago waste significantly affected the ADG (P<0.05). The consumption of dry matter (DM) and crude protein (CP) also increased with the supplementation of the sago waste, where the highest consumption of DM was on the treatment P2 (5.09 ± 1.27 kg/day), and the lowest on the treatment P0 (4.25 ± 1.69 kg/day), while consumption of CP was highest at treatment P2 (0.37 ± 0.09 kg/day), and the lowest on the treatment P3 (0.34 ± 0.06 kg/day), while the feed conversionshowed the lowest level on the treatment P2 (12.01 ± 3.35) and highest on the treatment P0 (18.10 ± 7.39). However, supplementation of sago waste were not affect CP consumption (P>0.05), but significant affect(P<0.05) DM consumption and feed conversion. Based on the results of this study it can be concluded that the sago waste as local resources have the potential to be used as a source of energy of feed supplement to beef cattle.

  8. Chromium removal from electroplating wastewater by coir pith.

    PubMed

    Suksabye, Parinda; Thiravetyan, Paitip; Nakbanpote, Woranan; Chayabutra, Supanee

    2007-03-22

    Coir pith is a by-product from padding used in mattress factories. It contains a high amount of lignin. Therefore, this study investigated the use of coir pith in the removal of hexavalent chromium from electroplating wastewater by varying the parameters, such as the system pH, contact time, adsorbent dosage, and temperature. The maximum removal (99.99%) was obtained at 2% (w/v) dosage, particle size <75microm, at initial Cr(VI) 1647mgl(-1), system pH 2, and an equilibrium time of 18h. The adsorption isotherm of coir pith fitted reasonably well with the Langmuir model. The maximum Cr(VI) adsorption capacity of coir pith at 15, 30, 45 and 60 degrees C was 138.04, 197.23, 262.89 and 317.65mgCr(VI)g(-1) coir pith, respectively. Thermodynamic parameters indicated an endothermic process and the adsorption process was favored at high temperature. Desorption studies of Cr(VI) on coir pith and X-ray absorption near edge structure (XANES) suggested that most of the chromium bound on the coir pith was in Cr(III) form due to the fact that the toxic Cr(VI) adsorbed on the coir pith by electrostatic attraction was easily reduced to less toxic Cr(III). Fourier transform infrared (FT-IR) spectrometry analysis indicated that the carbonyl (CO) groups and methoxy (O-CH(3)) groups from the lignin structure in coir pith may be involved in the mechanism of chromium adsorption. The reduced Cr(III) on the coir pith surface may be bound with CO groups and O-CH(3) groups through coordinate covalent bonding in which a lone pair of electrons in the oxygen atoms of the methoxy and carbonyl groups can be donated to form a shared bond with Cr(III).

  9. Remediation of lead from lead electroplating industrial effluent using sago waste.

    PubMed

    Jeyanthi, G P; Shanthi, G

    2007-01-01

    Heavy metals are known toxicants, which inflict acute disorders to the living beings. Electroplating industries pose great threat to the environment through heavy load of metals in the wastewater discharged on land and water sources. In the present study, sago processing waste, which is both a waste and a pollutant, was used to adsorb lead ions from lead electroplating industrial effluent. Two types of sago wastes, namely, coarse sago waste and fine sago waste were used to study their adsorption capacity with the batch adsorption and Freundlich adsorption isotherm. The parameters that were considered for batch adsorption were pH (4, 5 and 6), time of contact (1, 2 and 3 hrs), temperature (30, 37 and 45 degrees C) and dosage of the adsorbent (2,4 and 6 g/L). The optimal condition for the effective removal of lead was found to be pH 5, time of contact 3 hrs, temperature 30 degrees C and dosage 4 g/L with coarse sago waste than fine sago waste.

  10. Acid Pretreatment of Sago Wastewater for Biohydrogen Production

    NASA Astrophysics Data System (ADS)

    Illi Mohamad Puad, Noor; Rahim, Nurainin Farhan Abd; Suhaida Azmi, Azlin

    2018-03-01

    Biohydrogen has been recognized to be one of the future renewable energy sources and has the potential in solving the greenhouse effects. In this study, Enterobacter aerogenes (E. aerogenes) was used as the biohydrogen producer via dark fermentation process using sago wastewater as the substrate. However, pretreatment of sago wastewater is required since it consists of complex sugars that cannot be utilized directly by the bacteria. This study aimed to use acid pretreatment method to produce high amount of glucose from sago wastewater. Three different types of acid: sulfuric acid (H2SO4); hydrochloric acid (HCl) and nitric acid (HNO3) were screened for the best acid in producing a maximum amount of glucose. H2SO4 gave the highest amount of glucose which was 9.406 g/L. Design of experiment was done using Face-centred Central Composite Design (FCCCD) tool under Response Surface Methodology (RSM) in Design Expert 9 software. The maximum glucose (9.138 g/L) was recorded using 1 M H2SO4 at 100 °C for 60 min. A batch dark fermentation using E. aerogenes was carried out and it was found that pretreated sago wastewater gave a higher hydrogen concentration (1700 ppm) compared to the raw wastewater (410 ppm).

  11. Use of coir pith particles in composites with Portland cement.

    PubMed

    Brasileiro, Gisela Azevedo Menezes; Vieira, Jhonatas Augusto Rocha; Barreto, Ledjane Silva

    2013-12-15

    Brazil is the fourth largest world's producer of coconut (Cocos nucifera L.). Coconut crops generate several wastes, including, coir pith. Coir pith and short fibers are the byproducts of extracting the long fibers and account for approximately 70% of the mature coconut husk. The main use of coir pith is as an agricultural substrate. Due to its shape and small size (0.075-1.2 mm), this material can be considered as a particulate material. The aim of this study was to evaluate the use of coir pith as an aggregate in cementitious composites and to evaluate the effect of the presence of sand in the performance of these composites. Some composites were produced exclusively with coir pith particles and other composites with coir pith partially substituting the natural sand. The cementitious composites developed were tested for their physical and mechanical properties and characterized by X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy and Fourier transform infrared spectroscopy to evaluate the effect of coir pith particles addition in cement paste and sand-cement-mortar. The statistical significance of the results was evaluated by one-way analysis of variance (ANOVA) test followed by multiple comparisons of the means by Tukey's test that showed that the composites with coir pith particles, with or without natural sand, had similar mechanical results, i.e., means were not statistically different at 5% significance level. There was a reduction in bulk density and an improved post-cracking behavior in the composites with coir pith particles compared to conventional mortar and to cement paste. These composites can be used for the production of lightweight, nonstructural building materials, according to the values of compressive strength (3.97-4.35 MPa) and low bulk density (0.99-1.26 g/cm(3)). Copyright © 2013 Elsevier Ltd. All rights reserved.

  12. Sago worms as a nutritious traditional and alternative food for rural children in Southeast Sulawesi, Indonesia.

    PubMed

    Nirmala, Intan R; Trees; Suwarni; Pramono, Mochammad S

    2017-06-01

    The sago worm Rhynchophorus ferrugineus is a nutritious food source found in the remaining parts of a sago palm trunk after the removal of sago starch by farmers. The effort to increase sago worm consumption is investigated in an intervention study among children aged <5 years. Children aged 1-5 years were allocated to a sago worm inclusive diet (n=10) and to a control group eating a usual diet, but without sago worms (n=13). Snacks were served once per day (100 g) for 45 days and designed to contain similar amounts of vegetables (carrots and long beans) and other ingredients including rice, sticky rice, cassava, sweet potato, banana, or tofu with or without sago worms. Food preference was ascertained by interview. Anthropometric measurements were taken at baseline and the endpoint. After mixing all food stuffs into one product for instance nasi gurih, protein and fat content in the intervention group was higher compared to control group (8.8 g and 7.3 g vs 4.7 g and 0.5 g respectively). In the intervention group receiving complementary feeding with sago worms, children's height changed minimally as did the control group (0.3 vs 0.2 cm); no difference was observed between the groups regarding weight or height. Sago worm consumption can diversify the diet through usage in various dishes, so improving its overall nutritional quality. Worm addition in an intervention program does not compromise, but maintains nutritional value. Local use adds affordability and sustainability to the food and health systems in a sago-consuming culture, so contributing to food security.

  13. Cr(VI) adsorption from electroplating plating wastewater by chemically modified coir pith.

    PubMed

    Suksabye, Parinda; Thiravetyan, Paitip

    2012-07-15

    Coir pith samples were chemically modified by grafting with acrylic acid for the removal of Cr(VI) from electroplating wastewater. The presence of acrylic acid on the coir pith surface was verified by a scanning electron microscope with an electron dispersive x-ray spectrometer (SEM/EDX), Fourier transform infrared spectroscopy (FTIR) and thermogravimetry (TG). The carbonyl groups (C==O) from the carboxylic acids (COOH) increased on the coir pith surface after grafting with acrylic acid. In addition, the thermal stability of the acrylic acid-grafted coir pith also improved. The optimum conditions for grafting the acrylic acid on the coir pith consisted of 2 M acrylic acid and 0.00125 M ceric ammonium nitrate (CAN, as an initiator). The maximum Cr(VI) removal (99.99 ± 0.07%) was obtained with the following conditions: a 1.3% (w/v) dosage of acrylic acid-grafted coir pith, a system pH of 2, a contact time of 22 h, a temperature of 30 °C, a particle size of <150 μm and an initial Cr(VI) of 1,171 mg l(-1). At system pH of 2, Cr(VI) in the HCrO(4)(-) form can be adsorbed with acrylic acid-grafted coir pith via an electrostatic attraction. The adsorption isotherm of 2 M acrylic acid-grafted coir pith exhibited a good fit with the Langmuir isotherm. The maximum Cr(VI) adsorption capacity of the 2 M acrylic acid-grafted coir pith was 196.00 mg Cr(VI) g(-1) adsorbent, whereas for coir pith without grafting, the maximum Cr(VI) removal was 165.00 mg Cr(VI) g(-1) adsorbent. The adsorption capacity of the acrylic acid-grafted coir pith for Cr(VI) was higher compared to the original coir pith. This result was due to the enhancement of the carbonyl groups on the coir pith surface that may have involved the mechanism of chromium adsorption. The X-ray absorption near edged structure (XANES) and desorption studies suggested that most of the Cr(III) that presented on the acrylic acid-grafted coir pith was due to the Cr(VI) being reduced to Cr(III) on the adsorbent surface. FTIR

  14. Transesterification of sago starch and waste palm cooking oil in densified CO2

    NASA Astrophysics Data System (ADS)

    Muljana, H.; Sugih, A. K.; Christina, N.; Fangdinata, K.; Renaldo, J.; Rudy; Heeres, H. J.; Picchioni, F.

    2017-07-01

    In this work, the synthesis of biodegradable and yet renewable thermoplastics materials through a transesterification reaction of sago starch and waste palm cooking oil (WPO) in densified CO2 as the solvent is reported. The aim of this research is to investigate the potential used of sago starch and WPO as raw materials in the thermoplastics starch synthesis. The starch esters was successfully synthesized using sago starch and WPO as reagent in densified CO2 as shown from the presence of carbonyl group (C=O, 1743 cm-1) in the FT-IR spectra coupled with the presence of the proton (1H-NMR) of the fatty acid in the starch backbone (0.8 - 2 ppm). The product crystallinity decreases as shown in XRD results and resulting with a change in the thermal properties (melting and crystalline temperature) of the products. In addition, the products show a different granular morphology and a higher hydrophobicity compared with native sago starch. This research shows the potential used of sago starch and WPO in the thermoplastics starch synthesis and opens a new perspective on the product application.

  15. The Effect of Sunlight in Parenchyma Pith Cells Diameter of Manihot esculenta

    NASA Astrophysics Data System (ADS)

    Susanti, D.; Aziz, D. N.; Astuti, W.; Nuraeni, E.

    2017-03-01

    Sunlight is one of the factors that effect on the grow of a plant. Manihot esculenta is one of the plants that easily found in Indonesia because its role as staple food. The aim of this research is to know the correlation between sunlight the grow of parenchyma pith cells diameter of Manihot esculenta. Independent variable in this research is sunlight, and dependent variable is the parenchyma pith cells diameter of Manihot esculenta. Data was collected is in qualitative and quantitative form. Qualitative data gotten gained by morphology observation. The parenchyma pith cells of Manihot esculenta that is affected by sunlight in 1310 x 10 Lux, morphologically has hexagon, cell walls thick, solid state, and regular composition. Meanwhile, the parenchyma pith cells that has less sunlight (363 x 10 Lux) has a hexagon shape, thin cell walls thin, soft state, and irregular composition. Qualitative data suported by quantitative data. The size of parenchyma pith cells diameter that is affected by sunlight in 1310 x 10 Lux 96,4 µm. While, the stem parenchyma pith cells diameter empulur that has less sunlight (363 x 10 Lux) is 129,8 µm.

  16. Esterified sago waste for engine oil removal in aqueous environment.

    PubMed

    Ngaini, Zainab; Noh, Farid; Wahi, Rafeah

    2014-01-01

    Agro-waste from the bark of Metroxylon sagu (sago) was studied as a low cost and effective oil sorbent in dry and aqueous environments. Sorption study was conducted using untreated sago bark (SB) and esterified sago bark (ESB) in used engine oil. Characterization study showed that esterification has successfully improved the hydrophobicity, buoyancy, surface roughness and oil sorption capacity of ESB. Sorption study revealed that water uptake of SB is higher (30 min static: 2.46 g/g, dynamic: 2.67 g/g) compared with ESB (30 min static: 0.18 g/g, dynamic: 0.14 g/g). ESB, however, showed higher oil sorption capacity in aqueous environment (30 min static: 2.30 g/g, dynamic: 2.14) compared with SB (30 min static: 0 g/g, dynamic: 0 g/g). ESB has shown great poTENTial as effective oil sorbent in aqueous environment due to its high oil sorption capacity, low water uptake and high buoyancy.

  17. Enzymatic production of maltodextrins derived from sago flour using heat-stable alpha-amylase and pullulanase

    NASA Astrophysics Data System (ADS)

    Laga, A.; Syarifuddin, A.; Dirpan, A.

    2018-05-01

    Maltodextrins are produced by starch modification in a partial hydrolysis thus altered physical sago properties. Sago as one of starch resources has characteristic with high amylopectin that influences high viscosity during cooking. Partial hydrolysis or liquefaction will influences starch hydrolysis and the size of maltodextrin produced. The aim of this study was to analyze the degree of sago starch hydrolysis during the enzymatic process using single α-amylase and combination with pullulanase The starting solids content was 20% (w/v), with adjusted pH to 6.5, and calcium (Ca2+ ions) addition as high as 50 ppm. The majority of starches used in the study contain 0.2 % (w/v), to combination of 0.2 % (w/w) and 0, 3 gram per kg of sago. The sago suspension temperatures were started from 105 °C lowered to 60 °C for 30 minutes, respectively. Optimum liquefied starch yields, which accounted for virtually all of the starch present, were obtained at temperatures of 80°C and above, for 120 minutes, with each sampling every 20 minutes. Observed parameters were levels of reducing sugars, degree of hydrolysis, and refined sago starch. The result showed that there was a significant increase in reducing sugars, degree of hydrolysis during 120 minutes until liquefaction process for both enzymatic treatments. The amount of reducing sugars was 95.76 g/L at 120 min for the single α-amylase and 98.84 g/L combination with pullulanase. The degree of hydrolysis was 37.93 % at 120 minutes for the single α-amylase and 37.32 % combination with pullulanase, whereas 0.035 % and 0.038 % for refined sago starch value respectively.

  18. Combination of near infrared spectroscopy and chemometrics for authentication of taro flour from wheat and sago flour

    NASA Astrophysics Data System (ADS)

    Rachmawati; Rohaeti, E.; Rafi, M.

    2017-05-01

    Taro flour on the market is usually sold at higher price than wheat and sago flour. This situation could be a cause for adulteration of taro flour from wheat and sago flour. For this reason, we will need an identification and authentication. Combination of near infrared (NIR) spectrum with multivariate analysis was used in this study to identify and authenticate taro flour from wheat and sago flour. The authentication model of taro flour was developed by using a mixture of 5%, 25%, and 50% of adulterated taro flour from wheat and sago flour. Before subjected to multivariate analysis, an initial preprocessing signal was used namely normalization and standard normal variate to the NIR spectrum. We used principal component analysis followed by discriminant analysis to make an identification and authentication model of taro flour. From the result obtained, about 90.48% of the taro flour mixed with wheat flour and 85% of taro flour mixed with sago flour were successfully classified into their groups. So the combination of NIR spectrum with chemometrics could be used for identification and authentication of taro flour from wheat and sago flour.

  19. An Environmental Impact Analysis of Semi-Mechanical Extraction Process of Sago Starch: Life Cycle Assessment (LCA) Perspective

    NASA Astrophysics Data System (ADS)

    Yusuf, M. A.; Romli, M.; Suprihatin; Wiloso, E. I.

    2018-05-01

    Industrial activities use material, energy and water resources and generate greenhouse gas (GHG). Currently, various regulations require industry to measure and quantify the emissions generated from its process activity. LCA is a method that can be used to analyze and report the environmental impact of an activity that uses resources and generates waste by an industrial activity. In this work, LCA is used to determine the environmental impact of a semi-mechanical extraction process of sago industry. The data was collected through the sago industry in Cimahpar, Bogor. The extraction of sago starch consists of stem cutting, rasping, mixing, filtration, starch sedimentation, washing, and drying. The scope of LCA study covers the harvesting of sago stem, transportation to extraction site, and the starch extraction process. With the assumption that the average transportation distance of sago stem to extraction site is 200 km, the GHG emission is estimated to be 325 kg CO2 eq / ton of sundried sago starch. This figure is lower than that reported for maize starch (1120 kg CO2 eq), potato starch (2232 kg CO2 eq) and cassava starch (4310 kg CO2 eq). This is most likely due to the uncounted impact from the use of electrical energy on the extraction process, which is currently being conducted. A follow-up study is also underway to formulate several process improvement scenarios to derive the design of sago starch processing that generates the minimum emissions.

  20. What happens in the pith stays in the pith: tissue-localized defense responses facilitate chemical niche differentiation between two spatially separated herbivores.

    PubMed

    Lee, Gisuk; Joo, Youngsung; Kim, Sang-Gyu; Baldwin, Ian T

    2017-11-01

    Herbivore attack is known to elicit systemic defense responses that spread throughout the host plant and influence the performance of other herbivores. While these plant-mediated indirect competitive interactions are well described, and the co-existence of herbivores from different feeding guilds is common, the mechanisms of co-existence are poorly understood. In both field and glasshouse experiments with a native tobacco, Nicotiana attenuata, we found no evidence of negative interactions when plants were simultaneously attacked by two spatially separated herbivores: a leaf chewer Manduca sexta and a stem borer Trichobaris mucorea. T. mucorea attack elicited jasmonic acid (JA) and jasmonoyl-l-isoleucine bursts in the pith of attacked stems similar to those that occur in leaves when M. sexta attacks N. attenuata leaves. Pith chlorogenic acid (CGA) levels increased 1000-fold to levels 6-fold higher than leaf levels after T. mucorea attack; these increases in pith CGA levels, which did not occur in M. sexta-attacked leaves, required JA signaling. With plants silenced in CGA biosynthesis (irHQT plants), CGA, as well as other caffeic acid conjugates, was demonstrated in both glasshouse and field experiments to function as a direct defense protecting piths against T. mucorea attack, but not against leaf chewers or sucking insects. T. mucorea attack does not systemically activate JA signaling in leaves, while M. sexta leaf-attack transiently induces detectable but minor pith JA levels that are dwarfed by local responses. We conclude that tissue-localized defense responses allow tissue-specialized herbivores to share the same host and occupy different chemical defense niches in the same hostplant. © 2017 The Authors The Plant Journal © 2017 John Wiley & Sons Ltd.

  1. Effect of incubation time of sago (metroxylon sago) waste by local microorganism ″ginta″ on ph, crude protein, and crude fiber content

    NASA Astrophysics Data System (ADS)

    Ginting, Nurzainah; Pase, E.

    2018-03-01

    This study aims to examine the effect of incubation times of sago waste by local microorganism (MOL) “Ginta” to the crude protein and crude fiber content in relation to finding a cheap and good quality ruminants feed alternative. Incubation times were 0 hours to 144 hours. The data obtained were analyzed using Completely Randomize Design consisting of seven treatments and three replications. The result showed that the duration of incubation of sago waste by local microorganism (MOL) “Ginta” caused pH reduction, improved crude protein and crude fiber content. pH reduction was from 7.03 at 0 hour to 4.05 at 144 hours incubation. The highest increased in crude protein was H6U3 (5.58%) : 144 hours incubation and the lowest was H0U2 (3.22%) : 0 hour incubation while the highest crude fiber was H0U1 (19.99%) : 0 hour incubation and the lowest was H6U3 (18.23%) : 144 hours incubation. It can be concluded that incubation of sago waste triggered lower pH, higher crude protein and lower crude fiber than uninoculated. A recommendation could be given on using MOL ‘Ginta” in order to produce a cheap and good quality ruminans feed alternative.

  2. Measurement and modeling of transfer functions for lightning coupling into the Sago mine.

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Morris, Marvin E.; Higgins, Matthew B.

    2007-04-01

    This report documents measurements and analytical modeling of electromagnetic transfer functions to quantify the ability of cloud-to-ground lightning strokes (including horizontal arc-channel components) to couple electromagnetic energy into the Sago mine located near Buckhannon, WV. Two coupling mechanisms were measured: direct and indirect drive. These transfer functions are then used to predict electric fields within the mine and induced voltages on conductors that were left abandoned in the sealed area of the Sago mine.

  3. Bio-cellulose Production by Beijerinckia fluminensis WAUPM53 and Gluconacetobacter xylinus 0416 in Sago By-product Medium.

    PubMed

    Voon, W W Y; Muhialdin, B J; Yusof, N L; Rukayadi, Y; Meor Hussin, A S

    2018-06-19

    Bio-cellulose is the microbial extracellular cellulose that is produced by growing several microorganisms on agriculture by-products, and it is used in several food applications. This study aims to utilize sago by-product, coconut water, and the standard medium Hestrin-Schramm as the carbon sources in the culture medium for bio-cellulose production. The bacteria Beijerinkia fluminensis WAUPM53 and Gluconacetobacter xylinus 0416 were selected based on their bio-cellulose production activity. The structure was determined by Fourier transform infrared spectroscopy and scanning electron microscopy, while the toxicity safety was evaluated by brine shrimp lethality test. The results of Fourier transform infrared spectroscopy showed that the bio-cellulose produced by B. fluminensis cultivated in sago by-products was of high quality. The bio-cellulose production by B. fluminensis in the sago by-product medium was slightly higher than that in the coconut water medium and was comparable with the production in the Hestrin-Schramm medium. Brine shrimp lethality test confirmed that the bio-cellulose produced by B. fluminensis in the sago by-product medium has no toxicity, which is safe for applications in the food industry. This is the first study to determine the high potential of sago by-product to be used as a new carbon source for the bio-cellulose production.

  4. Column study of chromium(VI) adsorption from electroplating industry by coconut coir pith.

    PubMed

    Suksabye, Parinda; Thiravetyan, Paitip; Nakbanpote, Woranan

    2008-12-15

    The removal of Cr(VI) from electroplating wastewater by coir pith was investigated in a fixed-bed column. The experiments were conducted to study the effect of important parameters such as bed depth (40-60cm) and flow rate (10-30ml min(-1)). At 0.05 C(t)/C(0), the breakthrough volume increased as flow rate decreased or a bed depth increased due to an increase in empty bed contact time (EBCT). The bed depth service time model (BDST) fit well with the experimental data in the initial region of the breakthrough curve, while the simulation of the whole curve using non-linear regression analysis was effective using the Thomas model. The adsorption capacity estimated from the BDST model was reduced with increasing flow rate, which was 16.40mg cm(-3) or 137.91mg Cr(VI)g(-1) coir pith for the flow rates of 10ml min(-1) and 14.05mg cm(-3) or 118.20mg Cr(VI)g(-1) coir pith for the flow rates of 30ml min(-1). At the highest bed depth (60cm) and the lowest flow rate (10mlmin(-1)), the maximum adsorption reached 201.47mg Cr(VI)g(-1) adsorbent according to the Thomas model. The column was regenerated by eluting chromium using 2M HNO(3) after adsorption studies. The desorption of Cr(III) in each of three cycles was about 67-70%. The desorption of Cr(III) in each cycle did not reach 100% due to the fact that Cr(V) was present through the reduction of Cr(VI), and was still in coir pith, possibly bound to glucose in the cellulose part of coir pith. Therefore, the Cr(V) complex cannot be desorbed in solution. The evidence of Cr(V) signal was observed in coir pith, alpha-cellulose and holocellulose extracted from coir pith using electron spin resonance (ESR).

  5. Characterization of Briquette from the Corncob Charcoal and Sago Stem Alloys

    NASA Astrophysics Data System (ADS)

    Lestari, Lina; Inda Variani, Viska; Nyoman Sudiana, I.; Purnama Sari, Dewi; Ode Sitti Ilmawati, Wa; Sahaluddin Hasan, Erzam

    2017-05-01

    The briquettes fabricated from charcoal of corncob (zea mays,L) and sago stem (metroxilon sago rottb) have been produced and characterized. The samples were prepared step by step carefully. The charcoal powder filtered by strainer with mesh size of 70-80 to get the homogeneous particle size. Briquettes are made by mixing corncob charcoal powder, sago stem charcoal and sago adhesive with a mass ratio of 4:5:1, 4.5: 4.5: 1, 5:4:1. The materials are mixed with hot water and stirred to get homogeneous blend. Then they are compacted by pressure of 34.66kg/cm2, 69.32kg/cm2, and 103.98kg/cm2 to form a cylindrical shape with diameter of 4 cm. The cylindrical briquettes then were dried at temperature of 60°C for 48 hours. After dried, the samples where then characterized their density and water, ash, volatile matter, fixed carbon contents. The burning rate, combustion temperature, and ignition time were also determined. The experimental results show that the briquettes have average densities from 0.602 to 0.717gr/cm3. The density increase with the increasing of forming pressure. The increasing of pressure also result in the decreasing of moisture content from 2.669% to 0.842%. The ash content is found from 3.459% to 8.766%. Volatile matter and fixed carbon are varies from 13.658% and 21.168% and 67.667% to 80.758% respectively. The lowest burning rate is 0.0898gr/s and the optimum burning temperature is 499.2°C with the lowest ignition time of 1.58 minutes. These briquette’s parameters agree wit the quality standard of industrial briquette.

  6. 6. WORKERS COLLECTING SAGO PONDWEED, RED TOP GRASS, LEAFY PONDWEED, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    6. WORKERS COLLECTING SAGO PONDWEED, RED TOP GRASS, LEAFY PONDWEED, WATER MILFOIL, AND OTHER AQUATIC PLANTS FOR TRANSPLANTING FROM A COULEE SIX MILES AWAY FROM THE REFUGE - Upper Souris National Wildlife Refuge Dams, Souris River Basin, Foxholm, Surrey (England), ND

  7. Physicochemical properties of soils in the sago palm (Metroxylon spp.) growing area of Surat Thani province Thailand

    NASA Astrophysics Data System (ADS)

    Ruairuen, W.; Sparrow, E. B.; Fochesatto, G. J.

    2016-12-01

    Sago palm is one of the most important plants for sustainable agriculture and rural development in tropical swampy and peaty soils. Where no major crops can grow without drainage or soil improvement. It stores large quantities of starch which can be further processed into various basic raw materials for food, animal feed, industrial uses and alternative energy. This study aims to investigate the physicochemical properties of soil across the sago palm growing areas at Surat Thani province Thailand, where major of sago palms growth naturally exists. The soil samples from three districts Khiri Rat Nikhom (KR; 9 sampling sites), Kanchanadit (KD; 5 sampling sites), and Khian Sa (KS; 2 sampling sites) were studied and compared at 0-15 cm depth during March to June 2016. Observations indicated that the physicochemical properties of soil varied in each growing area. Soil bulk densities averages were lower in KD (0.52 g cm-3) than those in KR (0.58 g cm-3) and KS (0.57 g cm-3). Soil texture around KD and KS were dominated by silty loam. While in KR soil texture was dominated by sandy loam. The average soil conductivity in KS (5.68 mS m-1) was higher than KR (2.62 mS m-1) and KD (1.65 mS m-1). Furthermore, we found the sago palms grow well in a range of soil pH from 5.52 to 7.15, average soil pH: KS (6.8) and KD (6.96), while acid in KR (5.84). We also discuss the conservation activities to adequately protect sago palm, most of which are significantly threatened by habitat destruction and unsustainable harvesting.

  8. The effect of different levels of sunflower head pith addition on the properties of model system emulsions prepared from fresh and frozen beef.

    PubMed

    Sariçoban, Cemalettin; Yilmaz, Mustafa Tahsin; Karakaya, Mustafa; Tiske, Sümeyra Sultan

    2010-01-01

    The effect of sunflower head pith on the functional properties of emulsions was studied by using a model system. Oil/water (O/W) model emulsion systems were prepared from fresh and frozen beef by the addition of the pith at five concentrations. Emulsion capacity (EC), stability (ES), viscosity (EV), colour and flow properties of the prepared model system emulsions were analyzed. The pith addition increased the EC and ES and the highest EC and ES values were reached when 5% of pith added; however, further increase in the pith concentration caused an inverse trend in these values. Fresh beef emulsions had higher EC and ES values than did frozen beef emulsions. One percent pith concentration was the critic level for the EV values of fresh beef emulsions. EV values of the emulsions reached a maximum level at 5% pith level, followed by a decrease at 7% pit level.

  9. Analysis of In-Situ Spectral Reflectance of Sago and Other Palms: Implications for Their Detection in Optical Satellite Images

    NASA Astrophysics Data System (ADS)

    Rendon Santillan, Jojene; Makinano-Santillan, Meriam

    2018-04-01

    We present a characterization, comparison and analysis of in-situ spectral reflectance of Sago and other palms (coconut, oil palm and nipa) to ascertain on which part of the electromagnetic spectrum these palms are distinguishable from each other. The analysis also aims to reveal information that will assist in selecting which band to use when mapping Sago palms using the images acquired by these sensors. The datasets used in the analysis consisted of averaged spectral reflectance curves of each palm species measured within the 345-1045 nm wavelength range using an Ocean Optics USB4000-VIS-NIR Miniature Fiber Optic Spectrometer. This in-situ reflectance data was also resampled to match the spectral response of the 4 bands of ALOS AVNIR-2, 3 bands of ASTER VNIR, 4 bands of Landsat 7 ETM+, 5 bands of Landsat 8, and 8 bands of Worldview-2 (WV2). Examination of the spectral reflectance curves showed that the near infra-red region, specifically at 770, 800 and 875 nm, provides the best wavelengths where Sago palms can be distinguished from other palms. The resampling of the in-situ reflectance spectra to match the spectral response of optical sensors made possible the analysis of the differences in reflectance values of Sago and other palms in different bands of the sensors. Overall, the knowledge learned from the analysis can be useful in the actual analysis of optical satellite images, specifically in determining which band to include or to exclude, or whether to use all bands of a sensor in discriminating and mapping Sago palms.

  10. Preparation of sago starch-based biocomposite reinforced microfibrillated cellulose of bamboo assisted by mechanical treatment

    NASA Astrophysics Data System (ADS)

    Silviana, S.; Hadiyanto, H.

    2017-06-01

    The utilization of green composites by using natural fibres is developed due to their availability, ecological benefits, and good properties in mechanical and thermal. One of the potential sources is bamboo that has relative high cellulose content. This paper was focused on the preparation of sago starch-based reinforced microfribrillated cellulose of bamboo that was assisted by mechanical treatment. Microfibrillated cellulose of bamboo was prepared by isolation of cellulose with chemical treatment. Preparation of bamboo microfibrillated cellulose was conducted by homogenizers for dispersing bamboo cellulose, i.e. high pressure homogenizer and ultrasonic homogenizer. Experiments were elaborated on several variables such as the concentration of bamboo microfibrillated cellulose dispersed in water (1-3 %w) and the volume of microfibrillated cellulose (37.5-75%v). Four %w of sago starch solution was mixed with bamboo microfibrillated cellulose and glycerol with plasticizer and citric acid as cross linker. This paper provided the analysis of tensile strength as well as SEM for mechanical and morphology properties of the biocomposite. The results showed that the preparation of sago starch-based biocomposite reinforced bamboo microfibrillated cellulose by using ultrasonic homogenizer yielded the highest tensile strength and well dispersed in the biocomposite.

  11. Experimental and kinetic studies on methylene blue adsorption by coir pith carbon.

    PubMed

    Kavitha, D; Namasivayam, C

    2007-01-01

    Varying the parameters such as agitation time, dye concentration, adsorbent dose, pH and temperature carried out the potential feasibility of thermally activated coir pith carbon prepared from coconut husk for removal of methylene blue. Greater percentage of dye was removed with decrease in the initial concentration of dye and increase in amount of adsorbent used. Kinetic study showed that the adsorption of dye on coir pith carbon was a gradual process. Lagergren first-order, second-order, intra particle diffusion model and Bangham were used to fit the experimental data. Equilibrium isotherms were analysed by Langmuir, Freundlich, Dubnin-Radushkevich, and Tempkin isotherm. The adsorption capacity was found to be 5.87 mg/g by Langmuir isotherm for the particle size 250-500 microm. The equilibrium time was found to be 30 and 60 min for 10 and 20 mg/L and 100 min for 30, 40 mg/L dye concentrations, respectively. A maximum removal of 97% was obtained at natural pH 6.9 for an adsorbent dose of 100 mg/50 mL and 100% removal was obtained for an adsorbent dose of 600 mg/50 mL of 10 mg/L dye concentration. The pH effect and desorption studies suggest that chemisorption might be the major mode of the adsorption process. The change in entropy (DeltaS0) and heat of adsorption (DeltaH0) of coir pith carbon was estimated as 117.20 J/mol/K and 30.88 kJ/mol, respectively. The high negative value of change in Gibbs free energy indicates the feasible and spontaneous adsorption of methylene blue on coir pith carbon.

  12. Uranium removal from aqueous solution by coir pith: equilibrium and kinetic studies.

    PubMed

    Parab, Harshala; Joshi, Shreeram; Shenoy, Niyoti; Verma, Rakesh; Lali, Arvind; Sudersanan, M

    2005-07-01

    Basic aspects of uranium adsorption by coir pith have been investigated by batch equilibration. The influence of different experimental parameters such as final solution pH, adsorbent dosage, sorption time, temperature and various concentrations of uranium on uptake were evaluated. Maximum uranium adsorption was observed in the pH range 4.0-6.0. The Freundlich and Langmuir adsorption models were used for the mathematical description of the adsorption equilibrium. The equilibrium data fitted well to both the equilibrium models in the studied concentration range of uranium (200-800 mg/l) and temperatures (305-336 K). The coir pith exhibited the highest uptake capacity for uranium at 317 K, at the final solution pH value of 4.3 and at the initial uranium concentration of 800 mg/l. The kinetics of the adsorption process followed a second-order adsorption. The adsorbent used proved to be suitable for removal of uranium from aqueous solutions. 0.2 N HCl was effective in uranium desorption. The results indicated that the naturally abundant coir pith of otherwise nuisance value exhibited considerable potential for application in removal of uranium from aqueous solution.

  13. Engineering a lignocellulosic biosorbent--coir pith for removal of cesium from aqueous solutions: equilibrium and kinetic studies.

    PubMed

    Parab, Harshala; Sudersanan, M

    2010-02-01

    A novel method of engineering lignocellulosic biosorbent- coir pith (CP) by incorporation of nickel hexacyanoferrate (NiHCF), also referred to as Prussian blue analogue (PBA) inside its porous matrix is reported. Structural characterization confirmed the successful synthesis of NiHCF in the coir pith matrix. Sorption capacity of coir pith (CP) before and after loading of NiHCF was investigated for cesium (Cs) in batch equilibrium studies. Kinetic studies showed that the sorption process was rapid and saturation was attained within 30 min. The applicability of non linear Langmuir, Freundlich and Redlich Peterson isotherms was examined for the experimental data. The present studies revealed that there was nearly 100% increase in the sorption capacity of CP after its surface modification with NiHCF. Owing to its low cost, fast sorption kinetics and high uptake capacity, coir pith loaded with NiHCF (CP-NiHCF) seems to be one of the most promising biosorbents for recovery of cesium from liquid nuclear wastes. (c) 2009 Elsevier Ltd. All rights reserved.

  14. PtrWRKY19, a novel WRKY transcription factor, contributes to the regulation of pith secondary wall formation in Populus trichocarpa.

    PubMed

    Yang, Li; Zhao, Xin; Yang, Fan; Fan, Di; Jiang, Yuanzhong; Luo, Keming

    2016-01-28

    WRKY proteins are one of the largest transcription factor families in higher plants and play diverse roles in various biological processes. Previous studies have shown that some WRKY members act as negative regulators of secondary cell wall formation in pith parenchyma cells. However, the regulatory mechanism of pith secondary wall formation in tree species remains largely unknown. In this study, PtrWRKY19 encoding a homolog of Arabidopsis WRKY12 was isolated from Populus trichocarpa. PtrWRKY19 was expressed in all tissues tested, with highest expression in stems, especially in pith. PtrWRKY19 was located in the nucleus and functioned as a transcriptional repressor. Ectopic expression of PtrWRKY19 in an atwrky12 mutant successfully rescued the phenotype in pith cell walls caused by the defect of AtWRKY12, suggesting that PtrWRKY19 had conserved functions for homologous AtWRKY12. Overexpression of PtrWRKY19 in poplar plants led to a significant increase in the number of pith parenchyma cells. qRT-PCR analysis showed that lignin biosynthesis-related genes were repressed in transgenic plants. In transcient reporter assays, PtrWRKY19 was identified to repress transcription from the PtoC4H2 promoter containing the conserved W-box elements. These results indicated that PtrWRKY19 may function as a negative regulator of pith secondary wall formation in poplar.

  15. Ash content of loblolly pine wood as related to specific gravity, growth rate, and distance from pith

    Treesearch

    Charles W. McMillin

    1968-01-01

    In earlywood of Pinus taeda L. grown in central Louisiana, ash content generally decreased with increasing distance from the pith and icnreased with increases in rate of tree growth (as measured in rings per inch). Latewood ash content was unrelated to the gross wood factors of distance, from the pith, specific gravity, and growth rate. The ash...

  16. Removal of phosphate from aqueous solutions and sewage using natural and surface modified coir pith.

    PubMed

    Krishnan, K Anoop; Haridas, Ajit

    2008-04-01

    Iron impregnated coir pith (CP-Fe-I) can be effectively used for the removal of phosphate from aqueous streams and sewage. Iron impregnation on natural coir pith was carried out by drop by drop addition method. The effect of various factors such as pH, initial concentration of phosphate, contact time and adsorbent dose on phosphate adsorption was studied by batch technique. The pH at 3.0 favored the maximum adsorption of phosphate from aqueous solutions. The effect of pH on phosphate adsorption was explained by pH(zpc), phosphate speciation in solution and affinity of anions towards the adsorbent sites. A comparative study of the adsorption of phosphate using CP-Fe-I and CP (coir pith) was made and results show that the former one is five to six times more effective than the latter. Kinetic studies revealed that the adsorption process followed a pseudo-second order kinetic model. Adsorption followed Langmuir isotherm model. Column studies were conducted to examine the utility of the investigated adsorbent for the removal of phosphate from continuously flowing aqueous solutions.

  17. Subcritical carbon dioxide-water hydrolysis of sugarcane bagasse pith for reducing sugars production.

    PubMed

    Liang, Jiezhen; Chen, Xiaopeng; Wang, Linlin; Wei, Xiaojie; Wang, Huasheng; Lu, Songzhou; Li, Yunhua

    2017-03-01

    The aim of present study was to obtain total reducing sugars (TRS) by hydrolysis in subcritical CO 2 -water from sugarcane bagasse pith (SCBP), the fibrous residue remaining after papermaking from sugarcane bagasse. The optimum hydrolysis conditions were evaluated by L 16 (4 5 ) orthogonal experiments. The TRS yield achieved 45.8% at the optimal conditions: 200°C, 40min, 500rmin -1 , CO 2 initial pressure of 1MPa and liquid-to-solid ratio of 50:1. Fourier transform infrared spectrometry and two-dimensional heteronuclear single quantum coherence nuclear magnetic resonance were used to characterize hydrolysis liquor, treated and untreated SCBP, resulting in the removal of hemicelluloses to mainly produce xylose, glucose and arabinose during hydrolysis. The severity factors had no correlation to TRS yield, indicating that the simple kinetic processes of biomass solubilisation cannot perfectly describe the SCBP hydrolysis. The first-order kinetic model based on consecutive reaction was used to obtain rate constants, activation energies and pre-exponential factors. Copyright © 2016 Elsevier Ltd. All rights reserved.

  18. Effects of point massage of liver and stomach channel combined with pith and trotter soup on postpartum lactation start time.

    PubMed

    Luo, Qiong; Hu, Yin; Zhang, Hui

    2017-10-01

    Delay in lactation initiation causes maternal anxiety and subsequent adverse impact on maternal exclusive breast feeding. It is important to explore a safe and convenient way to promote lactation initiation. The feasibility of point massage of liver and stomach channel combined with pith and trotter soup on prevention of delayed lactation initiation was investigated in the present study. 320 women were enrolled and randomly divided into four groups, control group (80 women), point massage group (80 women), pith and trotter soup group (80 women), and massage + soup group (80 women) to compare the lactation initiation time. We found that women in point massage group, pith and trotter soup group and massage + soup group had earlier initiation of lactation compared with control group. Women in massage + soup group had the earliest initiation time of lactation. There were significant differences between massage + soup group and pith and trotter soup group. But, there were no significant differences between massage + soup group and massage group. We conclude that point massage of the liver and stomach channel is easy to operate and has the preventive effect on delayed lactation initiation. Impact statement What is already known on this subject: Initiation of lactation is a critical period in postpartum milk secretion. Delays in lactation initiation lead to maternal anxiety and have an adverse impact on maternal exclusive breastfeeding. Sucking frequently by babies and mammary massage might be effective but insufficient for delayed lactation initiation. What the results of this study add: We found in the present study that lactation initiation is significantly earlier in women receiving routine nursing combined with point massage of liver and stomach channel, or pith trotters soup, or massage of liver and stomach channel with pith and trotters soup than in a control group receiving routine nursing. These three methods are all effective, while the most

  19. Evaluating sago as a functional ingredient in dietetic mango ice cream.

    PubMed

    Patel, Ashish S; Jana, Atanu H; Aparnathi, Kishore D; Pinto, Suneeta V

    2010-10-01

    A low fat mango ice cream (2.4% milk fat) was prepared in a mechanized 'ice and salt' type freezer using powdered sago at 2.5% as a natural bulking agent along with sodium alginate at 0.025% as adjunct. The low fat mango ice cream was compared with control mango ice cream having 10% milk fat and 0.15% sodium alginate as stabilizer. Both control as well as experimental ice creams contained 20% mango pulp solids. To impart richness to low fat mango ice cream, flavour enhancers like Cream Plus and Butter Buds were used at levels of 0.2% and 0.05%, respectively. The dietetic low fat ice creams compared well in sensory colour and appearance, flavour, body and texture, and melting quality to that of control ice cream. Incorporation of 2.5% powdered sago and 0.2% Cream Plus as flavour adjunct is recommended in the manufacture of 'low-fat' mango ice cream. The energy values for control and dietetic mango ice cream was 202.8 and 142.9 kcal/100 g, respectively, which represents about 30% reduction in calorie. The cost of ice cream per liter was Rs 39.9, Rs 37.6 and Rs 49.7 for experimental ice creams containing Cream Plus and Butter Bud, and control, respectively.

  20. Effect of Agitation in Alkalization Process on the Characteristics of Sodium Carboxymethyl Sago and Cassava Starches

    NASA Astrophysics Data System (ADS)

    Titi, C. S.; Fachrudin, R.; Ruriani, E.; Yuliasih, I.

    2018-05-01

    Sodium carboxymethyl starch (Sodium CMS) is a modified starch prepared by two successive processes, alkalization and etherification. Alkalization will change the activated hydroxyl group of starch to more reactive alkoxide (St-O-), and then carboxymethyl group will substitute the hydroxyl group into sodium CMS. This research investigated the effect of agitation (1000 rpm of stirring and 4000 rpm of homogenization) in alkalization process to the modification of native starch into sodium CMS. Cassava and sago starches were mixed with sodium hydroxide (1.8 and 1.9 moles per mole anhydrous glucose units). The combination of NaOH and homogenizing gave the highest degrees of substitution for cassava (DS 0.73) and sago (DS 0.55) starches. The sodium CMS characteristics (paste clarity, water and oil absorption capacities, solubility, swelling power) were a function of mixing method but not on the amount of NaOH used.

  1. Utilization of α-amylase enzyme from Bacillus stearothermophilus RSAII1B for maltodextrin production from sago starch

    NASA Astrophysics Data System (ADS)

    Arfah, R. A.; Ahmad, A.; Dali, S.; Djide, M. N.; Mahdalia; Arif, A. R.

    2018-03-01

    The dried sago flour derived from Palopo contains 28.80% amylose and 91.23% total carbohydrate. Based on the data, sago starch has the potential to become an alternative raw material for themaltodextrin production. Maltodextrin is one of the starch derivative products produced by hydrolysis process using the α-amylase enzyme with amaximum DE (dextrose equivalent) value of 20. The use of maltodextrin for food and pharmaceutical industries is increasing because of maltodextrin is widely used as thickener filler, surfactant and sugar substitute in milk powder. The aims of this study are to optimize the addition of enzyme concentration and hydrolysis time of α -amylase enzyme to obtain high quality ofmaltodextrin This study also aimed to characterization the obtained maltodextrin. The first step was isolation and purification α-amylase from the isolate of Bacillus stearothermophilus RSAII1B, followed by determination of the α-amylase concentration (0.05%, 0.07% and 0.09%) in 2.0% starch substrate, and the hydrolysis time ofα-amilase (60, 90, 120, 240 minutes). Maltodextrin characters observed were dextrose equivalent (DE), reducing sugar, moisture content, pH changes, color, solubility, viscosity, and total plate count (TPC). The results showed that the value of DE was 12.31, reducing sugar was 11.4%; water content was 10.92%; pH was 4.85; The color of maltodextrin powder was white bone color; solubility was 153.2 g/L; Viscositywas 210-240 cps, TPCwas 380 cfu/g. Maltodextrins produced from sago starch using the α-amylase enzyme from B.stearothermophillus RSAIIm met the quality requirements of SNI 7599: 2010.

  2. Coconut coir pith lignin: A physicochemical and thermal characterization.

    PubMed

    Asoka Panamgama, L; Peramune, P R U S K

    2018-07-01

    The structural and thermal features of coconut coir pith lignin, isolated by three different extraction protocols incorporating two different energy supply sources, were characterized by different analytical tools. The three different chemical extraction protocols were alkaline - 7.5% (w/v) NaOH, organosolv - 85% (v/v) formic and acetic acids at 7:3 (v/v) ratio and polyethylene glycol (PEG): water ratio at 80:20wt%. The two sources of energy were thermal or microwave. Raw lignins were modified by epichlorohydrin to enhance reactivity, and the characteristics of raw and modified lignins were comparatively analysed. Using the thermal energy source, the alkaline and organosolv processes obtained the highest and lowest lignin yields of 26.4±1.5wt% and 3.4±0.2wt%, respectively, as shown by wet chemical analysis. Specific functional group analysis by Fourier transform infrared spectra (FTIR) revealed that significantly different amounts of hydroxyl and carbonyl groups exist in alkaline, organosolv and PEG lignins. Thermogravimetric analysis (TGA) illustrated that the lowest degradation onset temperature was recorded for organosolv lignin, and the overall order was organosolvpith can be performed efficiently with several protocols and that those methods offer practical value to industry. Copyright © 2018 Elsevier B.V. All rights reserved.

  3. Sago-Type Palms Were an Important Plant Food Prior to Rice in Southern Subtropical China

    PubMed Central

    Yang, Xiaoyan; Barton, Huw J.; Wan, Zhiwei; Li, Quan; Ma, Zhikun; Li, Mingqi; Zhang, Dan; Wei, Jun

    2013-01-01

    Poor preservation of plant macroremains in the acid soils of southern subtropical China has hampered understanding of prehistoric diets in the region and of the spread of domesticated rice southwards from the Yangtze River region. According to records in ancient books and archaeological discoveries from historical sites, it is presumed that roots and tubers were the staple plant foods in this region before rice agriculture was widely practiced. But no direct evidences provided to test the hypothesis. Here we present evidence from starch and phytolith analyses of samples obtained during systematic excavations at the site of Xincun on the southern coast of China, demonstrating that during 3,350–2,470 aBC humans exploited sago palms, bananas, freshwater roots and tubers, fern roots, acorns, Job's-tears as well as wild rice. A dominance of starches and phytoliths from palms suggest that the sago-type palms were an important plant food prior to the rice in south subtropical China. We also believe that because of their reliance on a wide range of starch-rich plant foods, the transition towards labour intensive rice agriculture was a slow process. PMID:23667584

  4. Hanging angles of two electrostatically repelling pith balls of different masses

    NASA Astrophysics Data System (ADS)

    Tran, Phuc G.; Mungan, Carl E.

    2011-09-01

    An analytic solution can be derived for the angles of two mutually repelling charged pith balls of unequal mass hanging from strings from a common point of attachment. Just as in the equal-mass case, a cubic equation is found for the square of the sine of either angle, and an approximation can be used to avoid Cardano's formula for small angles. These results extend a standard problem treated in introductory undergraduate courses in electricity and magnetism.

  5. Graphene-Like 2D Porous Carbon Nanosheets Derived from Cornstalk Pith for Energy Storage Materials

    NASA Astrophysics Data System (ADS)

    Gao, Kezheng; Niu, Qingyuan; Tang, Qiheng; Guo, Yaqing; Wang, Lizhen

    2018-01-01

    Biomass materials from different organisms or different parts (even different periods) of the same organism have different microscopic morphologies, hierarchical pore structures and even elemental compositions. Therefore, carbon materials inheriting the unique hierarchical microstructure of different biomass materials may exhibit significantly different electrochemical properties. Cornstalk pith and cornstalk skin (dried by freeze-drying) exhibit significantly different microstructures due to their different biological functions. The cornstalk skin-based carbon (S-carbon) exhibits a thick planar morphology, and the Barrett-Emmett-Teller (BET) surface area is only about 332.07 m2 g-1. However, cornstalk pith-based carbon (P-carbon) exhibits a graphene-like 2D porous nanosheet structure with a rough, wrinkled morphology, and the BET surface area is about 805.17 m2 g-1. In addition, a P-carbon supercapacitor exhibits much higher specific capacitance and much better rate capability than an S-carbon supercapacitor in 6 M potassium hydroxide (KOH) electrolyte.

  6. Adsorptive removal of 2-chlorophenol by low-cost coir pith carbon.

    PubMed

    Namasivayam, C; Kavitha, D

    2003-03-17

    Adsorption of 2-chlorophenol (2-CP) by coir pith carbon was carried out by varying the parameters such as agitation time, 2-CP concentration, adsorbent dose, pH and temperature. Adsorption equilibrium reached at 40, 60, 80 and 100 min for 2-CP concentration of 10, 20, 30 and 40 mg/l, respectively. Adsorption followed second-order kinetics. The adsorption equilibrium data obeyed Freundlich isotherm. Acidic pH was favorable for the adsorption of 2-CP. Desorption studies showed that chemisorption plays a major role in the adsorption process. Copyright 2003 Elsevier Science B.V.

  7. Paired dating of pith and outer edge (terminus) samples from prehispanic Caribbean wooden sculptures

    Treesearch

    Fiona Brock; Joanna Ostapkowicz; Christopher Bronk Ramsey; Alex Wiedenhoeft; Caroline Cartwright

    2012-01-01

    Radiocarbon dating of historical and archaeological wood can be complicated, sometimes involving issues of “inbuilt” age in slow-growing woods, and/or the possibility of reuse or long delays between felling and use of the wood. Terminus dates can be provided by dating the sapwood, or the outermost edge of heartwood, while a date from the pith can give an indication of...

  8. Morphological characteristics of loblolly pine wood as related to specific gravity, growth rate and distance from pith

    Treesearch

    Charles W. McMillin

    1968-01-01

    Earlywood and latewood tracheid length and transverse cellular dimensions of wood removed from stems of loblolly pine (Pinus taeda L.) and factorially aegregated by specific gravity, rings from the pith, and growth rate were determined from sample chips. The independent relationships of each factor with fiber morphology are described.

  9. Optimization of Ozonation Process for the Reduction of Excess Sludge Production from Activated Sludge Process of Sago Industry Wastewater Using Central Composite Design

    PubMed Central

    Subha, B.; Muthukumar, M.

    2012-01-01

    Sago industries effluent containing large amounts of organic content produced excess sludge which is a serious problem in wastewater treatment. In this study ozonation has been employed for the reduction of excess sludge production in activated sludge process. Central composite design is used to study the effect of ozone treatment for the reduction of excess sludge production in sago effluent and to optimise the variables such as pH, ozonation time, and retention time. ANOVA showed that the coefficient determination value (R 2) of VSS and COD reduction were 0.9689 and 0.8838, respectively. VSS reduction (81%) was achieved at acidic pH 6.9, 12 minutes ozonation, and retention time of 10 days. COD reduction (87%) was achieved at acidic pH 6.7, 8 minutes of ozonation time, and retention time of 6 days. Low ozonation time and high retention time influence maximum sludge reduction, whereas low ozonation time with low retention time was effective for COD reduction. PMID:22593666

  10. Draft genome of a Xanthomonas perforans strain associated with pith necrosis.

    PubMed

    Torelli, Emanuela; Aiello, Dalia; Polizzi, Giancarlo; Firrao, Giuseppe; Cirvilleri, Gabriella

    2015-02-01

    Xanthomonas perforans causes bacterial spot of tomato and pepper. A genome draft of an unusual isolate (strain 4P1S2), differing in that it was associated with stem pith necrosis, was assembled from Illumina MiSeq sequencing data using the draft of X. perforans strain 91-118 as a reference. The resulting draft (accession number JRWW00000000) largely overlapped with the reference draft. In addition, the reads not mapping on the reference assembly were selected and used for a further assembly, that revealed a large putative plasmid. The analysis of the predicted proteins showed only few gene features that could be potentially implicated in the switch of a phytopathological behavior. © FEMS 2015. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  11. Evaluation of the alpha-1 and alpha-2 adrenoceptor-mediated effects of a series of dimethoxy-substituted tolazoline derivatives in the cardiovascular system of the pithed rat.

    PubMed

    Ruffolo, R R; Messick, K

    1985-01-01

    The alpha-1 and alpha-2 adrenoceptor-mediated effects of a series of dimethoxy-substituted tolazoline derivatives were investigated in the cardiovascular system of the pithed rat. The 2,5- and 3,5-dimethoxy-substituted tolazoline derivatives produced vasopressor responses that were inhibited by the alpha-1 adrenoceptor antagonist, prazosin (0.1 mg/kg i.v.), and were not affected by the alpha-2 adrenoceptor antagonist, yohimbine (1 mg/kg i.v.), suggesting that these derivatives selectively activate postsynaptic vascular alpha-1 adrenoceptors. The 2,5- and 3,5-dimethoxy-substituted derivatives of tolazoline did not produce an alpha-2 adrenoceptor-mediated inhibition of neurogenic tachycardia in cord-stimulated pithed rats and were therefore presumed to be devoid of alpha-2 adrenoceptor agonist activity. In contrast, 2,3-dimethoxytolazoline produced a vasopressor effect that was inhibited by yohimbine but not by prazosin, suggesting selective activation of postsynaptic vascular alpha-2 adrenoceptors. Consistent with this observation is the fact that 2,3-dimethoxytolazoline elicited a dose-dependent, alpha-2 adrenoceptor-mediated inhibition of neurogenic tachycardia in cord-stimulated pithed rat. 3,4-Dimethoxytolazoline was a weak alpha-1 adrenoceptor agonist in the vasculature of the pithed rat and was devoid of agonist activity at alpha-2 adrenoceptors. However, 3,4-dimethoxytolazoline was found to be an alpha-2 adrenoceptor antagonist of similar potency as yohimbine. The results of the present study indicate that dimethoxy-substituted derivatives of tolazoline possess different activities and selectivities at alpha-1 and alpha-2 adrenoceptors depending upon the positions of substitution.(ABSTRACT TRUNCATED AT 250 WORDS)

  12. Coating hydroxiapatite on stainless steel 316 L by using sago starch as binder with dip-coating method

    NASA Astrophysics Data System (ADS)

    Fadli, A.; Akbar, F.; Prabowo, A.; Hidayah, P. H.

    2018-04-01

    Hydroxyapatite (HA) is a mineral form of naturally occurring apatite calcium with Ca10(PO4)6(OH)2 formula. One of the major innovations in the field of bone reconstruction is to apply HA as a surface coating on a mechanically strong implant metal and to improve the stability of bone implants thereby increasing the lifetime of the metal implants. Pure hydroxyapatite has poor mechanical properties so it is necessary to add sago starch as a binder to combine the strength and hardness of metal surfaces with bioactive properties of hydroxyapatite by Dip Coating method. Stainless steel 316L is the most commonly used alloy as an implant for bones and teeth due to its excellent corrosion and oxidation resistance and is easily formed. In this study, hydroxyapatite coatings used fixed variables as hydroxyapatite mass (10 grams), aquades mass (20 grams), dipping time (20 seconds), and calcination conditions (800°C, 1 hour). The variables are sago starch mass (1, 1.25, 1.5 gram) and stirring time (16, 20, 24 hours). The shear strength value is higher in the addition of 1.25, 10, 20, and again in the binder ratio of 1.5; 10; 20. The addition of stirring time causes a decrease in shear strength. The highest shear strength value obtained was 3.07 MPa. The layer attached to the substrate is a hydroxyapatite with a composition of 99.4% as evidenced by the results of XRD analysis.

  13. Uptake of dyes by a promising locally available agricultural solid waste: coir pith.

    PubMed

    Namasivayam, C; Radhika, R; Suba, S

    2001-01-01

    The adsorption of rhodamine-B and acid violet by coir pith carbon was carried out by varying the parameters such as agitation time, dye concentration, adsorbent dose and pH. The adsorption followed both Langmuir and Freundlich isotherms. The adsorption capacity was found to be 2.56 mg and 8.06 mg dye per g of the adsorbent for rhodamine-B and acid violet, respectively. Adsorption of dyes followed first order rate kinetics. Acidic pH was favorable for the adsorption of acid violet and alkaline pH was favorable to rhodamine-B. Desorption studies showed that alkaline pH was favorable for the desorption of acid violet and acidic pH was favorable for the desorption of rhodamine-B.

  14. Adsorption characteristics of cadmium(II) onto functionalized poly(hydroxyethylmethacrylate)-grafted coconut coir pith.

    PubMed

    Anirudhan, Thayyath Sreenivasan; Divya, Lekshmi; Rijith, Sreenivasan

    2010-07-01

    This study explored the feasibility of utilizing a novel adsorbent, poly(hydroxyethylmethacrylate)-grafted coconut coir pith with carboxyl functionality (PGCP-COOH) for the removal of cadmium(II) from water and wastewater. Maximum removal of 99.9% was observed for an initial concentration of 25 mg/L at pH 6.0 and adsorbent dose of 2.0 g/L. The first-order reversible kinetic model and Langmuir isotherm model were resulted in high correlation coefficients and described well the adsorption of Cd(II) onto PGCP-COOH. The complete removal of 22.4 mg/L Cd(II) from fertilizer industry wastewater was achieved by 2.0 g/L PGCP-COOH. The reusability of the PGCP-COOH for several cycles was demonstrated using 0.1 M HCl solution.

  15. Hypothermia augments non-cholinergic neuronal bronchoconstriction in pithed guinea-pigs.

    PubMed

    Rechtman, M P; King, R G; Boura, A L

    1991-08-16

    Electrical stimulation at C4-C7 in the spinal canal of pithed guinea-pigs injected with atropine, d-tubocurarine and pentolinium caused frequency-dependent bronchoconstriction. Such non-cholinergic responses to electrical stimulation, unlike responses to substance P, were abolished by pretreatment with capsaicin but not by mepyramine or propranolol. Bronchoconstrictor responses to electrical stimulation were inversely related to rectal temperature (between 30-40 degrees C) whereas responses to substance P increased with increasing temperature over the same range. Ouabain (i.v.) augmented responses to electrical stimulation at 35-37 degrees C but depressed those at 30-32 degrees C. Both morphine and the alpha 2-adrenoceptor agonist B-HT920 (i.v.) inhibited non-cholinergic-mediated bronchoconstrictor responses at 30-32 degrees C. These results stress the importance of adequate control of body temperature in this preparation. Lowered body temperature may increase neuronal output of neuropeptides whilst depressing bronchial smooth muscle sensitivity. The data support previous conclusions regarding the role of Na+/K+ activated ATPase in temperature-induced changes in sensitivity to bronchoconstrictor stimuli.

  16. Antibacterial, mechanical, and barrier properties of sago starch film incorporated with Betel leaves extract.

    PubMed

    Nouri, Leila; Mohammadi Nafchi, Abdorreza

    2014-05-01

    The antimicrobial, mechanical and barrier properties and light transmission of sago starch film incorporated with different percentage of Betel leaf extract (5%, 10%, 20%, and 30%) were evaluated. With regard to mechanical properties, tensile strength decreased when the percentage of extract increased. Elongation at break (%) and seal strength (N/m) increased with increasing percentage of extract from 5% to 20%, while decreased for films containing 30% extract due to heterogeneity of films in this percentage. With regard to barrier properties, water vapour and oxygen barrier properties decreased in all samples when percentage of the extract increased. Antimicrobial activity of all the films increased against both Gram positive and Gram negative bacteria as percentage of Betel leaf extract increased, except for Psuedomonas aeruginosa, which was not susceptible at any percentage of the extract. Copyright © 2014 Elsevier B.V. All rights reserved.

  17. Role of 5-HT7 receptors in the inhibition of the vasodepressor sensory CGRPergic outflow in pithed rats.

    PubMed

    Cuesta, Cristina; García-Pedraza, José Ángel; García, Mónica; Villalón, Carlos M; Morán, Asunción

    2014-10-01

    The role of calcitonin gene-related peptide (CGRP) in the modulation of vascular tone has been widely documented. Indeed, electrical stimulation of the perivascular sensory outflow in pithed rats induces vasodepressor responses by activation of CGRP receptors. This study investigated the role of 5-HT7 receptors in the inhibition of the rat vasodepressor sensory outflow. Male Wistar pithed rats were pretreated with i.v. continuous infusions of hexamethonium and methoxamine, followed by physiological saline or AS-19 (a 5-HT7 receptor agonist). Then, electrical stimulation of the spinal cord resulted in frequency-dependent decreases in DBP. The infusions of AS-19, as compared to those of saline, inhibited the vasodepressor responses induced by electrical stimulation without affecting those to i.v. bolus injections of exogenous α-CGRP. This inhibition by AS-19 was abolished by the antagonists pimozide (5-HT7) or sulfisoxazole (ETA), but not by indomethacin (COX1/2) or losartan (AT1), at doses that did not affect per se the electrically-induced vasodepressor responses. Interestingly, glibenclamide (an ATP-dependent K(+) channel blocker) attenuated these vasodepressor responses. The present results suggest that AS-19-induced inhibition of the rat vasodepressor sensory CGRPergic outflow is mainly mediated by 5-HT7 receptors via endothelin release, with the possible involvement of ATP-dependent K(+) channels. Copyright © 2014 Elsevier Inc. All rights reserved.

  18. Mercury(II) removal from aqueous solutions and wastewaters using a novel cation exchanger derived from coconut coir pith and its recovery.

    PubMed

    Anirudhan, T S; Divya, L; Ramachandran, M

    2008-09-15

    A new adsorbent (PGCP-COOH) having carboxylate functional group at the chain end was synthesized by grafting poly(hydroxyethylmethacrylate) onto coconut coir pith, CP (a coir industry-based lignocellulosic residue), using potassium peroxydisulphate as an initiator and in the presence of N,N'-methylenebisacrylamide as a cross-linking agent. The adsorbent was characterized with the help of infrared spectroscopy, powder X-ray diffraction, scanning electron microscopy, and potentiometric titrations. The ability of PGCP-COOH to remove Hg(II) from aqueous solutions was assessed using batch adsorption technique under kinetic and equilibrium conditions. Adsorbent exhibits very high adsorption potential for Hg(II) and more than 99.0% removal was achieved in the pH range 5.5-8.0. Adsorption process was found to follow first-order-reversible kinetics. An increase of ionic strength of the medium caused a decrease in metal removal, indicating the occurrence of outer-sphere surface complex mechanism. The equilibrium data were fitted well by the Freundlich isotherm model (R(2)=0.99; chi(2)=1.81). The removal efficiency was tested using chlor-alkali industry wastewater. Adsorption isotherm experiments were also conducted for comparison using a commercial carboxylate-functionalized ion exchanger, Ceralite IRC-50. Regeneration experiments were tried for four cycles and results indicate a capacity loss of <9.0%.

  19. Net photosynthesis and respiration of sago pondweed (Potamogeton pectinatus) exposed to herbicides

    USGS Publications Warehouse

    Fleming, W.J.; Ailstock, M.S.; Momot, J.J.; Hughes, Jane S.; Biddinger, Gregory R.; Mones, Eugene

    1995-01-01

    We determined net photosynthesis and respiration rates for sago pondweed (potamogeton pectinatus) exposed to various concentrations of 11 herbicides widely used in Maryland during the past decade. Net photosynthesis and respiration were determined by measuring changes in the. oxygen content of solutions containing dilutions of technical grade herbicides. At 20-22? C and 58 umol/m2/sec of photosynthetically active radiation (PAR), oxygen production of undosed plants averaged 0.72-2.03 mg/g fresh wt/h. Respiration rates of undosed plants averaged 0.46-0.60 mg O2/g fresh wt/h. Nominal herbicide concentrations (ng/L) that reduced net photosynthesis by 5O percent (IC5O) were: metribuzin, 8; atrazine, 29; cyanazine, 32; linuron, 70; simazine, 164; and paraquat, 240. IC5O values for 2,4-D, acifluorfen, glyphosate and metolachlor exceeded the maximum test concentration of 10,000 ng/L. The IC5O value for alachlor was estimated to be between 1,000 and 10,000 ng/L. None of the herbicides tested had a significant effect on dark respiration.

  20. Removal of phenanthrene from soil by co-cultures of bacteria and fungi pregrown on sugarcane bagasse pith.

    PubMed

    Chávez-Gómez, B; Quintero, R; Esparza-García, F; Mesta-Howard, A M; Zavala Díaz de la Serna, F J; Hernández-Rodríguez, C H; Gillén, T; Poggi-Varaldo, H M; Barrera-Cortés, J; Rodríguez-Vázquez, R

    2003-09-01

    Sixteen co-cultures composed of four bacteria and four fungi grown on sugarcane bagasse pith were tested for phenanthrene degradation in soil. The four bacteria were identified as Pseudomonas aeruginose, Ralstonia pickettii, Pseudomonas sp. and Pseudomonas cepacea. The four fungi were identified as: Penicillium sp., Trichoderma viride, Alternaria tenuis and Aspergillus terrus that were previously isolated from different hydrocarbon-contaminated soils. Fungi had a statistically significant positive (0.0001

  1. Response of sago pondweed, a submerged aquatic macrophyte, to herbicides in three laboratory culture systems

    USGS Publications Warehouse

    Fleming, W.J.; Ailstock, M.S.; Momot, J.J.; Norman, C.M.; Gorsuch, Joseph W.; Lower, William R.; Wang, Wun-cheng; Lewis, M.A.

    1991-01-01

    The phytotoxicity of atrazine, paraquat, glyphosate, and alachlor to sago pondweed (Potamogeton pectinatus), a submerged aquatic macrophyte, was tested under three types of laboratory culture conditions. In each case, tests were conducted in static systems, the test period was four weeks, and herbicide exposure was chronic, resulting from a single addition of herbicide to the test vessels at the beginning of the test period. The three sets of test conditions employed were(1) axenic cultures in 125-mL flasks containing a nutrient media and sucrose; (2) a microcosm system employing 18.9-L buckets containing a sand, shell, and peat substrate; and (3) an algae-free system employing O.95-L jars containing reconstituted freshwater and a nutrient agar substrate. The primary variable measured was biomass production. Plants grew well in all three test systems, with biomass of untreated plants increasing by a factor of about 5 to 6.5 during the four-week test period. Biomass production in response to herbicide exposure differed significantly among culture systems, which demonstrates the need for a standardized testing protocol for evaluating the effects of toxics on submerged aquatic plants.

  2. Pharmacological analysis of the inhibition produced by moxonidine and agmatine on the vasodepressor sensory CGRPergic outflow in pithed rats.

    PubMed

    Rubio-Beltrán, Eloísa; Labastida-Ramírez, Alejandro; Hernández-Abreu, Oswaldo; MaassenVanDenBrink, Antoinette; Villalón, Carlos M

    2017-10-05

    Calcitonin gene-related peptide (CGRP) plays a role in several (patho)physiological functions, and modulation of its release is considered a therapeutic target. In this respect, electrical spinal (T 9 --T 12 ) stimulation of the perivascular sensory outflow in pithed rats produces vasodepressor responses mediated by CGRP release. This study investigated the role of imidazoline I 1 and I 2 receptors in the inhibition by moxonidine and agmatine of these vasodepressor responses. Male Wistar pithed rats (pretreated i.v. with 25mg/kg gallamine and 2mg/kg⋅min hexamethonium) received i.v. continuous infusions of methoxamine (20μg/kg⋅min) followed by physiological saline (0.02ml/min), moxonidine (1, 3, 10 or 30μg/kg⋅min) or agmatine (1000 or 3000μg/kg⋅min). Under these conditions, electrical stimulation (0.56-5.6Hz; 50V; 2ms) of the spinal cord (T 9 -T 12 ) produced frequency-dependent vasodepressor responses which were: (i) unchanged during saline infusion; and (ii) inhibited during the above infusions of moxonidine or agmatine. Moreover, using i.v. administrations, the inhibition by 3μg/kg⋅min moxonidine or 3000μg/kg⋅min agmatine (which failed to inhibit the vasodepressor responses by α-CGRP; 0.1-1µg/kg) was: (i) unaltered after saline (1ml/kg), rauwolscine (300μg/kg; α 2 -adrenoceptor antagonist) or BU224 (300μg/kg; imidazoline I 2 receptor antagonist); and (ii) reversed after AGN 192403 (3000μg/kg; imidazoline I 1 receptor antagonist). This reversion was relatively more pronounced after AGN 192403 plus rauwolscine. These blocking doses of antagonists lacked any effects on the electrically-induced vasodepressor responses. Therefore, the inhibition of the vasodepressor sensory CGRPergic outflow by moxonidine and agmatine is mainly mediated by prejunctional imidazoline I 1 receptors on perivascular sensory nerves. Copyright © 2017 Elsevier B.V. All rights reserved.

  3. Conservation and Management of the Endangered Fiji Sago Palm, Metroxylon vitiense, in Fiji

    NASA Astrophysics Data System (ADS)

    Morrison, Clare; Rounds, Isaac; Watling, Dick

    2012-05-01

    Recovery planning is a key component of many threatened species conservation initiatives and can be a powerful awareness raising tool. One of the largest impediments to conservation efforts in the Pacific region however, is the lack of ecological data and its subsequent effects on the development of feasible and useful recovery plans for threatened species. Without these plans, the understaffed, underfunded and often technically ill-equipped conservation agencies face huge difficulties in planning, prioritizing and conducting conservation activities to adequately protect biodiversity. The Fiji sago palm, Metroxylon vitiense, is an endemic endangered palm species whose survival is heavily dependent on a feasible species recovery plan. It is geographically restricted and threatened by habitat destruction and overexploitation for thatch for the tourism industry and palm heart consumption by local consumers. Despite its threatened status, M. vitiense is not currently protected by national or international legislation. Recent field surveys and extensive stakeholder consultation have resulted in the production of a species recovery plan highlighting the importance of the species and advocating sustainable harvesting rather than complete bans to promote conservation. This article summarizes the recovery plan and its current effects on the status of M. vitiense in Fiji. We also discuss the role of different stakeholders in the conservation of M. vitiense, including the absence of significant behavioral changes by the largest consumer - the tourism industry, and the importance of recovery plans for biodiversity conservation in the Pacific.

  4. Removal of chromium(VI) from water and wastewater using surfactant modified coconut coir pith as a biosorbent.

    PubMed

    Namasivayam, C; Sureshkumar, M V

    2008-05-01

    Coconut coir pith, an agricultural solid waste was used as biosorbent for the removal of chromium(VI) after modification with a cationic surfactant, hexadecyltrimethylammonium bromide. Optimum pH for Cr(VI) adsorption was found to be 2.0. Reduction of Cr(VI) to Cr(III) occurred to a slight extent during the removal. Langmuir, Freundlich and Dubinin Radushkevich (D-R) isotherms were used to model the adsorption equilibrium data and the system followed all the three isotherms. The adsorption capacity of the biosorbent was found to be 76.3 mg g(-1), which is higher or comparable to the adsorption capacity of various adsorbents reported in literature. Kinetic studies showed that the adsorption obeyed second order and Elovich model. Thermodynamic parameters such as delta G0, delta H0 and delta S0 were evaluated, indicating that the overall adsorption process was endothermic and spontaneous. Effects of foreign anions were also examined. The adsorbent was also tested for the removal of Cr(VI) from electroplating effluent.

  5. Antibacterial activity and mechanical properties of partially hydrolyzed sago starch-alginate edible film containing lemongrass oil.

    PubMed

    Maizura, M; Fazilah, A; Norziah, M H; Karim, A A

    2007-08-01

    Edible films were prepared from a mixture of partially hydrolyzed sago starch and alginate (SA). Lemongrass oil (0.1% to 0.4%, v/w) and glycerol (0% and 20%, w/w) were incorporated in the films to act as natural antimicrobial agent and plasticizer, respectively. The films were characterized for antimicrobial activity, water vapor permeability (WVP), tensile strength (TS), percent elongation at break (%E), and water solubility (WS). Fourier transform infrared (FTIR) spectroscopy was conducted to determine functional group interactions between the matrix and lemongrass oil. The zone of inhibition was increased significantly (P < 0.05) by addition of lemongrass oil at all levels in the presence and the absence of glycerol. This indicates that the film containing lemongrass oil was effective against Escherichia coli O157:H7 at all levels. In the absence of glycerol, the tensile strength of film decreased as the oil content increased, but there was no significant (P > 0.05) difference in percent elongation. The percent elongation at break and WVP values for film with 20% glycerol was found to be increased significantly (P < 0.05) with an increase in lemongrass oil content. Addition of lemongrass oil did not have any interaction with the functional groups of films as measured by FTIR.

  6. Characteristics of Metroxylon sagu resistant starch type III as prebiotic substance.

    PubMed

    Zi-Ni, Tan; Rosma, Ahmad; Napisah, Hussin; Karim, Alias A; Liong, Min-Tze

    2015-04-01

    Resistant starch type III (RS3 ) was produced from sago (Metroxylon sagu) and evaluated for its characteristics as a prebiotic. Two RS3 samples designated sago RS and HCl-sago RS contained 35.71% and 68.30% RS, respectively, were subjected to hydrolyses by gastric juice and digestive enzymes and to absorption. Both sago RS and HCl-sago RS were resistant to 180 min hydrolysis by gastric acidity at pH 1 to 4 with less than 0.85% hydrolyzed. Both samples were also resistant toward hydrolysis by gastrointestinal tract enzymes and intestinal absorption with 96.75% and 98.69% of RS3 were recovered respectively after 3.5 h digestion and overnight dialysis at 37 °C. Sago RS3 supported the growth of both beneficial (lactobacilli and Bifidobacteria) and pathogenic microbes (Escherichia coli, Campylobacter coli, and Clostridium perfringens) in the range of 2.60 to 3.91 log10 CFU/mL. Hence, prebiotic activity score was applied to describe the extent to which sago RS3 supports selective growth of the lactobacilli and bifidobacteria strains over pathogenic bacteria. The highest scores were obtained from Bifidobacterium sp. FTDC8943 grown on sago RS (+0.26) and HCl-sago RS (+0.24) followed by L. bulgaricus FTDC1511 grown on sago RS (+0.21). The findings had suggested that sago RS3 has the prebiotic partial characteristics and it is suggested to further assess the suitability of sago RS3 as a prebiotic material. © 2015 Institute of Food Technologists®

  7. Comparison of stem morphology and anatomy of two alfalfa clonal lines exhibiting divergent cell wall composition.

    PubMed

    Gronwald, John W; Bucciarelli, Bruna

    2013-08-30

    In previous research, two alfalfa clonal lines (252 and 1283) were identified that exhibited environmentally stable differences in stem cell walls. Compared with stems of 1283, stems of 252 have a higher cell wall concentration and greater amounts of lignin and cellulose but reduced levels of pectic sugar residues. These results suggest greater deposition of secondary xylem and a reduction in pith in stems of 252 compared with 1283. The stem morphology and anatomy of first-cut and second-cut harvests of field-grown 1283 and 252 were examined. For both harvests, stems of 1283 were thicker and had a higher leaf/stem ratio compared with stems of 252. Stem cross-sections of both genotypes were stained for lignin, and the proportions of stem area that were pith and secondary xylem were measured using ImageJ. Stems of 252 exhibited greater deposition of secondary xylem and a reduction in pith proportion compared with stems of 1283 for the first-cut harvest, but this difference was not statistically significant for the second-cut harvest. The results indicate that the proportions of secondary xylem and pith are not environmentally stable in these two genotypes and hence cannot be the sole basis for the differences in cell wall concentration/composition. © 2012 Society of Chemical Industry.

  8. Kinetic studies of adsorption of thiocyanate onto ZnCl2 activated carbon from coir pith, an agricultural solid waste.

    PubMed

    Namasivayam, C; Sangeetha, D

    2005-09-01

    The adsorption of thiocyanate onto ZnCl2 activated carbon developed from coir pith was investigated to assess the possible use of this adsorbent. The influence of various parameters such as agitation time, thiocyanate concentration, adsorbent dose, pH and temperature has been studied. Adsorption followed second-order rate kinetics. Two theoretical adsorption isotherms, namely, Langmuir and Freundlich were used to describe the experimental results. The Langmuir adsorption capacity (Q0) was found to be 16.2 mg g(-1) of the adsorbent. The per cent adsorption was maximum in the pH range 3.0-7.0. pH effect and desorption studies showed that ion exchange and chemisorption mechanism are involved in the adsorption process. Thermodynamic parameters such as DeltaG0, DeltaH0 and DeltaS0 for the adsorption were evaluated. The negative values of DeltaH0 confirm the exothermic nature of adsorption. Effects of foreign ions on the adsorption of thiocyanate have been investigated. Removal of thiocyanate from ground water was also tested.

  9. Effects of progesterone on cardiovascular responses to amines and to sympathetic stimulation in the pithed rat

    PubMed Central

    Fozard, J. R.

    1971-01-01

    1. Blood pressure and heart rate responses to adrenaline, noradrenaline, tyramine, 5-hydroxytryptamine and stimulation of the spinal sympathetic outflow were measured in pithed rats pretreated either with progesterone (20 mg/kg daily for 14 days) or the vehicle solution of ethyl oleate. 2. Pretreatment with progesterone increased the durations but not the magnitudes of the blood pressure and heart rate responses to adrenaline and that phase of the response to sympathetic stimulation attributable to amine release from the adrenal medulla. 3. Responses to noradrenaline, tyramine, 5-hydroxytryptamine and that phase of the response to sympathetic stimulation associated with amine release from the sympathetic nerves were not significantly different in the two groups. 4. Pyrogallol (5 mg/kg) increased the duration but not the magnitude of responses to adrenaline, noradrenaline and sympathetic stimulation in both experimental groups. The increases in duration were consistently less in animals pretreated with progesterone than in controls. 5. Pretreatment with progesterone did not affect the total amount of radioactivity nor the proportion of catechol to non-catechol metabolites excreted in the urine during a period of 7·25 h following an intraperitoneal injection of (±) isoprenaline-7-3H. 6. It is concluded that the effects of progesterone may result from a localized decrease in catechol O-methyl transferase activity within the cardiovascular system. PMID:5280141

  10. Composition, Taste, Aroma, and Antioxidant Activity of Solidified Noncentrifugal Brown Sugars Prepared from Whole Stalk and Separated Pith of Sugarcane (Saccharum officinarum L.).

    PubMed

    Takahashi, Makoto; Ishmael, Mutanda; Asikin, Yonathan; Hirose, Naoto; Mizu, Masami; Shikanai, Takesi; Tamaki, Hajime; Wada, Koji

    2016-10-25

    In this study, 2 types of solidified noncentrifugal brown sugars (W-NCS and P-NCS) were prepared from the whole stalk and separated pith, respectively, of raw sugarcane (Saccharum officinarum L.). These products were discriminated in terms of their quality attributes, including color, sugars and minerals composition, taste, aroma, and antioxidant activity. The brown color of P-NCS was clearly different compared with that of W-NCS with a color difference value (ΔE * ) of 9.36. There was no difference in the sugars and minerals composition between the 2 types of sugar, which led to very similar taste profiles. However, P-NCS had a weaker aroma intensity than W-NCS did. Moreover, P-NCS retained more than 60% of the antioxidant activity of W-NCS. The information gleaned from this study might be used to select appropriate end-uses for these 2 types of sugars. © 2016 Institute of Food Technologists®.

  11. Arsenic(V) removal from aqueous solutions using an anion exchanger derived from coconut coir pith and its recovery.

    PubMed

    Anirudhan, T S; Unnithan, Maya R

    2007-01-01

    The performance of a new anion exchanger (AE) prepared from coconut coir pith (CP), for the removal of arsenic(V) [As(V)] from aqueous solutions was evaluated in this study. The adsorbent (CP-AE) carrying dimethylaminohydroxypropyl weak base functional group was synthesized by the reaction of CP with epichlorohydrin and dimethylamine followed by treatment of hydrochloric acid. IR spectroscopy results confirm the presence of -NH(+)(CH(3))(2)Cl(-) group in the adsorbent. XRD studies confirm the decrease of crystallinity in CP-AE compared to CP, and it favours the protrusion of the functional group into the aqueous medium. Batch experiments were conducted to examine the efficiency of the adsorbent on As(V) removal. Maximum removal of 99.2% was obtained for an initial concentration of 1 mgl(-1) As(V) at pH 7.0 and an adsorbent dose of 2 gl(-1). The kinetics of sorption of As(V) onto CP-AE was described using the pseudo-second-order model. The equilibrium isotherms were determined for different temperatures and the results were analysed using the Langmuir equation. The temperature dependence indicates an exothermic process. Utility of the adsorbent was tested by removing As(V) from simulated groundwater. Regeneration studies were performed using 0.1N HCl. Batch adsorption-desorption studies illustrate that CP-AE could be used to remove As(V) from ground water and other industrial effluents.

  12. Effect of cellulose nanocrystals (CNC) addition and citric acid as co-plasticizer on physical properties of sago starch biocomposite

    NASA Astrophysics Data System (ADS)

    Nasution, Halimatuddahliana; Afandy, Yayang; Al-fath, M. Thoriq

    2018-04-01

    Cellulose has potential applications in new high-performance materials with low environmental impact. Rattan biomass is a fiber waste from processing industry of rattan which contains 37,6% cellulose. The high cellulose contents of rattan biomass make it a source of cellulose nanocrystals as a filler in biocomposite. Isolation of alpha cellulose from biomass rattan was prepared by using three stages: delignification, alkalization, and bleaching. It was delignificated with 3,5% HNO3 and NaNO2, precipitated with 17,5% NaOH, bleaching process with 10% H2O2. Nanocrystals obtained through the hydrolysis of alpha cellulose using 45% H2SO4 and followed by mechanical processes of ultrasonication, centrifugation, and filtration with a dialysis membrane. Sago starch biocomposites were prepared using a solution casting method, which includes 1-4 wt % cellulose nanocrystals rattan biomass as fillers, 10-40 wt% citric acid as co-plasticizer and 30 wt% glycerol as plasticizer. The results of TEM and FTIR characteristic of cellulose nanocrystals show spherical like shape FTIR and chemical composition analysis demonstrated that lignin and hemicellulose structures were successfully removed. Biocomposite characteristic consists of density and water absorption. The results showed the highest density values were 0,266 gram/cm3 obtained at an additional of 3% cellulose nanocrystals rattan biomass and 30% citric acid. The lowest water absorption was 7,893% obtained at an additional of 4% cellulose nanocrystals rattan biomass and 10% citric acid.

  13. Tundra swan habitat preferences during migration in North Dakota

    USGS Publications Warehouse

    Earnst, Susan L.

    1994-01-01

    I studied tundra swan (Cygnus columbianus columbianus) habitat preference in North Dakota during autumn migration, 1988-89. Many thousand tundra swans stop in the Prairie Pothole region during autumn migration, but swan resource use has not been quantified. I examined habitat preference in relation to an index of sago pondweed (Potamogeton pectinatus) presence, extent of open water, and wetland size. I compared habitat preference derived from counts of all swans to those derived from foraging swans only and cygnets only. Foraging swans preferred wetlands with sago pondweed (P = 0.03); the number of foraging swans per wetland was >4 times higher on wetlands with sago pondweed than on wetlands without sago. In contrast, nonforaging swans did not prefer wetlands with sago pondweed (P = 0.85) but preferred large wetlands (P = 0.02) and those with a high proportion of contiguous open water (P < 0.01). Thus, conclusions about habitat preference derived from counts of all swans, most of which were nonforaging, would not have revealed the importance of sago pondweed. Cygnets were more likely to be feeding than adults (P = 0.03) and occurred proportionately more often in smaller flocks (P = 0.04), but cygnets and adults had similar habitat preferences.

  14. Genetic Transformation of Metroxylon sagu (Rottb.) Cultures via Agrobacterium-Mediated and Particle Bombardment

    PubMed Central

    Ibrahim, Evra Raunie

    2014-01-01

    Sago palm (Metroxylon sagu) is a perennial plant native to Southeast Asia and exploited mainly for the starch content in its trunk. Genetic improvement of sago palm is extremely slow when compared to other annual starch crops. Urgent attention is needed to improve the sago palm planting material and can be achieved through nonconventional methods. We have previously developed a tissue culture method for sago palm, which is used to provide the planting materials and to develop a genetic transformation procedure. Here, we report the genetic transformation of sago embryonic callus derived from suspension culture using Agrobacterium tumefaciens and gene gun systems. The transformed embryoids cells were selected against Basta (concentration 10 to 30 mg/L). Evidence of foreign genes integration and function of the bar and gus genes were verified via gene specific PCR amplification, gus staining, and dot blot analysis. This study showed that the embryogenic callus was the most suitable material for transformation as compared to the fine callus, embryoid stage, and initiated shoots. The gene gun transformation showed higher transformation efficiency than the ones transformed using Agrobacterium when targets were bombarded once or twice using 280 psi of helium pressure at 6 to 8 cm distance. PMID:25295258

  15. Expansive soil stabilization with coir waste and lime for flexible pavement subgrade

    NASA Astrophysics Data System (ADS)

    Narendra Goud, G.; Hyma, A.; Shiva Chandra, V.; Sandhya Rani, R.

    2018-03-01

    Expansive soil properties can be improved by various methods to make it suitable for construction of flexible pavement. The coir pith is the by-product (bio-waste) generated from coir industry during extraction of coir fiber from coconut husk. Openly disposed coir pith can make the surrounding areas unhygienic. This bio-waste can be one of the potential materials to stabilize the expansive soils. In the present study coir pith and lime are used as stabilizers. Different combinations of coir pith contents (1%, 2% and 3%) and lime contents (2%, 3% and 4%)are used to study the behavior of expansive soil. Unconfined compressive strength (UCS) of unstabilized and stabilized soils was determined. Optimum content of coir pith and lime are determined based on UCS of the soil. California bearing ratio of soil determined at optimum contents of coir pith and lime. Flexible pavement layer compositions for two levels of traffic using stabilized soil subgrade.

  16. On tide-induced Lagrangian residual current and residual transport: 1. Lagrangian residual current

    USGS Publications Warehouse

    Feng, Shizuo; Cheng, Ralph T.; Pangen, Xi

    1986-01-01

    Residual currents in tidal estuaries and coastal embayments have been recognized as fundamental factors which affect the long-term transport processes. It has been pointed out by previous studies that it is more relevant to use a Lagrangian mean velocity than an Eulerian mean velocity to determine the movements of water masses. Under weakly nonlinear approximation, the parameter k, which is the ratio of the net displacement of a labeled water mass in one tidal cycle to the tidal excursion, is assumed to be small. Solutions for tides, tidal current, and residual current have been considered for two-dimensional, barotropic estuaries and coastal seas. Particular attention has been paid to the distinction between the Lagrangian and Eulerian residual currents. When k is small, the first-order Lagrangian residual is shown to be the sum of the Eulerian residual current and the Stokes drift. The Lagrangian residual drift velocity or the second-order Lagrangian residual current has been shown to be dependent on the phase of tidal current. The Lagrangian drift velocity is induced by nonlinear interactions between tides, tidal currents, and the first-order residual currents, and it takes the form of an ellipse on a hodograph plane. Several examples are given to further demonstrate the unique properties of the Lagrangian residual current.

  17. Quantifying seasonal fallback on invertebrates, pith, and bromeliad leaves by white-faced capuchin monkeys (Cebus capucinus) in a tropical dry forest.

    PubMed

    Mosdossy, Krisztina N; Melin, Amanda D; Fedigan, Linda M

    2015-09-01

    Fallback foods (FBFs) are hypothesized to shape the ecology, morphology, and behavior of primates, including hominins. Identifying FBFs is therefore critical for revealing past and present foraging adaptations. Recent research suggests invertebrates act as seasonal FBFs for many primate species and human populations. Yet, studies measuring the consumption of invertebrates relative to ecological variation are widely lacking. We address this gap by examining food abundance and entomophagy by primates in a seasonal forest. We study foraging behavior of white-faced capuchins (Cebus capucinus)-a species renowned for its intelligence and propensity for extractive foraging-along with the abundance of invertebrates, dietary ripe fruits, pith, and bromeliads. Consumption events and processing time are recorded during focal animal samples. We determine abundance of vegetative foods through phenological and density records. Invertebrates are collected in malaise, pan, and terrestrial traps; caterpillar abundance is inferred from frass traps. Invertebrates are abundant throughout the year and capuchins consume invertebrates-including caterpillars-frequently when fruit is abundant. However, capuchins spend significantly more time processing protected invertebrates when fruit and caterpillars are low in abundance. Invertebrate foraging patterns are not uniform. Caterpillar consumption is consistent with a preferred strategy, whereas capuchins appear to fallback on invertebrates requiring high handling time. Capuchins are convergent with hominins in possessing large brains and high levels of sensorimotor intelligence, thus our research has broad implications for primate evolution, including factors shaping cognitive innovations, brain size, and the role of entomophagy in the human diet. © 2015 Wiley Periodicals, Inc.

  18. Effect of factory effluents on physiological and biochemical contents of Gossypium hirsutum l.

    PubMed

    Muthusamy, A; Jayabalan, N

    2001-10-01

    The effect of sago and sugar factory effluents was studied on Gossypium hirsutum L. var. MCU 5 and MCU 11. Plants were irrigated with 0, 25, 50, 75 and 100% of effluents of both factories. At lower concentration (25%) of sugar factory effluents had stimulatory effect on all biochemical contents observed. Moreover, all concentration of sago factory effluents were found to have inhibitory effect on all biochemical contents except proline content which increased with increasing concentration of both the effluents. Plants growing on adjacent to sago and sugar factories or they irrigated with such type of polluted water, may accumulate the heavy metals found in both the effluents, at higher levels in plant products and if consumed may have similar effect on living organisms.

  19. Analysis and optimization of coagulation and flocculation process

    NASA Astrophysics Data System (ADS)

    Saritha, V.; Srinivas, N.; Srikanth Vuppala, N. V.

    2017-03-01

    Natural coagulants have been the focus of research of many investigators through the last decade owing to the problems caused by the chemical coagulants. Optimization of process parameters is vital for the effectiveness of coagulation process. In the present study optimization of parameters like pH, dose of coagulant and mixing speed were studied using natural coagulants sago and chitin in comparison with alum. Jar test apparatus was used to perform the coagulation. The results showed that the removal of turbidity was up to 99 % by both alum and chitin at lower doses of coagulant, i.e., 0.1-0.3 g/L, whereas sago has shown a reduction of 70-100 % at doses of 0.1 and 0.2 g/L. The optimum conditions observed for sago were 6 and 7 whereas chitin was stable at all pH ranges, lower coagulant doses, i.e., 0.1-0.3 g/L and mixing speed—rapid mixing at 100 rpm for 10 min and slow mixing 20 rpm for 20 min. Hence, it can be concluded that sago and chitin can be used for treating water even with large seasonal variation in turbidity.

  20. Additional Amphivasal Bundles in Pedicel Pith Exacerbate Central Fruit Dominance and Induce Self-Thinning of Lateral Fruitlets in Apple1[C][W

    PubMed Central

    Celton, Jean-Marc; Dheilly, Emmanuelle; Guillou, Marie-Charlotte; Simonneau, Fabienne; Juchaux, Marjorie; Costes, Evelyne; Laurens, François; Renou, Jean-Pierre

    2014-01-01

    Apple (Malus × domestica) trees naturally produce an excess of fruitlets that negatively affect the commercial value of fruits brought to maturity and impact their capacity to develop flower buds the following season. Therefore, chemical thinning has become an important cultural practice, allowing the selective removal of unwanted fruitlets. As the public pressure to limit the use of chemical agents increases, the control of thinning becomes a major issue. Here, we characterized the self-thinning capacity of an apple hybrid genotype from the tree scale to the molecular level. Additional amphivasal vascular bundles were identified in the pith of pedicels supporting the fruitlets with the lowest abscission potential (central fruitlet), indicating that these bundles might have a role in the acquisition of dominance over lateral fruitlets. Sugar content analysis revealed that central fruitlets were better supplied in sorbitol than lateral fruitlets. Transcriptomic profiles allowed us to identify genes potentially involved in the overproduction of vascular tissues in central pedicels. In addition, histological and transcriptomic data permitted a detailed characterization of abscission zone development and the identification of key genes involved in this process. Our data confirm the major role of ethylene, auxin, and cell wall-remodeling enzymes in abscission zone formation. The shedding process in this hybrid appears to be triggered by a naturally exacerbated dominance of central fruitlets over lateral ones, brought about by an increased supply of sugars, possibly through additional amphivasal vascular bundles. The characterization of this genotype opens new perspectives for the selection of elite apple cultivars. PMID:24550240

  1. Partitioning Residue-derived and Residue-induced Emissions of N2O Using 15N-labelled Crop Residues

    NASA Astrophysics Data System (ADS)

    Farrell, R. E.; Carverhill, J.; Lemke, R.; Knight, J. D.

    2014-12-01

    Estimates of N2O emissions in Canada indicate that 17% of all agriculture-based emissions are associated with the decomposition of crop residues. However, research specific to the western Canadian prairies (including Saskatchewan) has shown that the N2O emission factor for N sources in this region typically ranges between 0.2 and 0.6%, which is well below the current IPCC default emission factor of 1.0%. Thus, it stands to reason that emissions from crop residues should also be lower than those calculated using the current IPCC emission factor. Current data indicates that residue decomposition, N mineralization and N2O production are affected by a number of factors such as C:N ratio and chemical composition of the residue, soil type, and soil water content; thus, a bench-scale incubation study was conducted to examine the effects of soil type and water content on N2O emissions associated with the decomposition of different crop residues. The study was carried out using soils from the Black, Dark Brown, Brown, and Gray soil zones and was conducted at both 50% and 70% water-filled pore space (WFPS); the soils were amended with 15N-labeled residues of wheat, pea, canola, and flax, or with an equivalent amount of 15N-labeled urea; 15N2O production was monitored using a Picarro G5101-i isotopic N2O analyzer. Crop residue additions to the soils resulted in both direct and indirect emissions of N2O, with residue derived emissions (RDE; measured as 15N2O) generally exceeding residue-induced emissions (RIE) at 50% WFPS—with RDEs ranging from 42% to 88% (mean = 58%) of the total N2O. Conversely, at 70% WFPS, RDEs were generally lower than RIEs—ranging from 21% to 83% (mean = 48%). Whereas both water content and soil type had an impact on N2O production, there was a clear and consistent trend in the emission factors for the residues; i.e., emissions were always greatest for the canola residue and lowest for the wheat residue and urea fertilizer; and intermediate for pea

  2. 40 CFR 180.519 - Bromide ion and residual bromine; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Bromide ion and residual bromine... Tolerances § 180.519 Bromide ion and residual bromine; tolerances for residues. (a) General. The food additives, bromide ion and residual bromine, may be present in water, potable in accordance with the...

  3. 40 CFR 180.519 - Bromide ion and residual bromine; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 24 2011-07-01 2011-07-01 false Bromide ion and residual bromine... Tolerances § 180.519 Bromide ion and residual bromine; tolerances for residues. (a) General. The food additives, bromide ion and residual bromine, may be present in water, potable in accordance with the...

  4. Characterization of prejunctional 5-HT receptors mediating inhibition of sympathetic vasopressor responses in the pithed rat.

    PubMed Central

    Villalón, C. M.; Contreras, J.; Ramírez-San Juan, E.; Castillo, C.; Perusquía, M.; Terrón, J. A.

    1995-01-01

    1. It has recently been shown that continuous infusions of 5-hydroxytryptamine (5-HT) are able to inhibit, in a dose-dependent manner, the pressor responses induced by preganglionic (T7-T9) sympathetic stimulation in pithed rats pretreated with desipramine (50 micrograms kg-1, i.v.). This inhibitory effect, besides being significantly more pronounced at lower frequencies of stimulation (0.03-I Hz) and devoid of tachyphylaxis, is reversible after interrupting the infusions of 5-HT (up to 5.6 micrograms kg-1 min-1). In the present study we have characterized the pharmacological profile of the receptors mediating the above inhibitory effect of 5-HT. 2. The inhibition induced by 5.6 micrograms kg-1 min-1 of 5-HT on sympathetically-induced pressor responses was not blocked after i.v. treatment with physiological saline (1 ml kg-1), ritanserin (0.1 mg kg-1), MDL 72222 (0.15 mg kg-1) or tropisetron (3 mg kg-1), which did not modify the sympathetically-induced pressor responses per se, but was significantly antagonized by the 5-HT1-like and 5-HT2 receptor antagonist, methysergide (0.3 mg kg-1), which also produced a slight attenuation of the pressor responses to 0.03 and 0.1 Hz per se. 3. Unexpectedly and contrasting with methysergide, the 5-HT1-like and 5-HT2 receptor antagonists, methiothepin (0.01, 0.03 and 0.1 mg kg-1) and metergoline (1 and 3 mg kg-1), apparently failed to block the above 5-HT-induced inhibition. Nevertheless, it is noteworthy that these antagonists also blocked the electrically-induced pressor responses per se, presumably by blockade of vascular alpha 1-adrenoceptors and, indeed, this property might have masked their potential antagonism at the inhibitory 5-HT1-like receptors. 4. Consistent with the above findings, 5-carboxamidotryptamine (5-CT, a potent 5-HT1-like receptor agonist), metergoline and methysergide mimicked the inhibitory action of 5-HT with the following rank order of agonist potency: 5CT > > 5-HT > metergoline > or = methysergide. 5

  5. Rigid Residue Scan Simulations Systematically Reveal Residue Entropic Roles in Protein Allostery

    PubMed Central

    Liu, Jin

    2016-01-01

    Intra-protein information is transmitted over distances via allosteric processes. This ubiquitous protein process allows for protein function changes due to ligand binding events. Understanding protein allostery is essential to understanding protein functions. In this study, allostery in the second PDZ domain (PDZ2) in the human PTP1E protein is examined as model system to advance a recently developed rigid residue scan method combining with configurational entropy calculation and principal component analysis. The contributions from individual residues to whole-protein dynamics and allostery were systematically assessed via rigid body simulations of both unbound and ligand-bound states of the protein. The entropic contributions of individual residues to whole-protein dynamics were evaluated based on covariance-based correlation analysis of all simulations. The changes of overall protein entropy when individual residues being held rigid support that the rigidity/flexibility equilibrium in protein structure is governed by the La Châtelier’s principle of chemical equilibrium. Key residues of PDZ2 allostery were identified with good agreement with NMR studies of the same protein bound to the same peptide. On the other hand, the change of entropic contribution from each residue upon perturbation revealed intrinsic differences among all the residues. The quasi-harmonic and principal component analyses of simulations without rigid residue perturbation showed a coherent allosteric mode from unbound and bound states, respectively. The projection of simulations with rigid residue perturbation onto coherent allosteric modes demonstrated the intrinsic shifting of ensemble distributions supporting the population-shift theory of protein allostery. Overall, the study presented here provides a robust and systematic approach to estimate the contribution of individual residue internal motion to overall protein dynamics and allostery. PMID:27115535

  6. RRCRank: a fusion method using rank strategy for residue-residue contact prediction.

    PubMed

    Jing, Xiaoyang; Dong, Qiwen; Lu, Ruqian

    2017-09-02

    In structural biology area, protein residue-residue contacts play a crucial role in protein structure prediction. Some researchers have found that the predicted residue-residue contacts could effectively constrain the conformational search space, which is significant for de novo protein structure prediction. In the last few decades, related researchers have developed various methods to predict residue-residue contacts, especially, significant performance has been achieved by using fusion methods in recent years. In this work, a novel fusion method based on rank strategy has been proposed to predict contacts. Unlike the traditional regression or classification strategies, the contact prediction task is regarded as a ranking task. First, two kinds of features are extracted from correlated mutations methods and ensemble machine-learning classifiers, and then the proposed method uses the learning-to-rank algorithm to predict contact probability of each residue pair. First, we perform two benchmark tests for the proposed fusion method (RRCRank) on CASP11 dataset and CASP12 dataset respectively. The test results show that the RRCRank method outperforms other well-developed methods, especially for medium and short range contacts. Second, in order to verify the superiority of ranking strategy, we predict contacts by using the traditional regression and classification strategies based on the same features as ranking strategy. Compared with these two traditional strategies, the proposed ranking strategy shows better performance for three contact types, in particular for long range contacts. Third, the proposed RRCRank has been compared with several state-of-the-art methods in CASP11 and CASP12. The results show that the RRCRank could achieve comparable prediction precisions and is better than three methods in most assessment metrics. The learning-to-rank algorithm is introduced to develop a novel rank-based method for the residue-residue contact prediction of proteins, which

  7. Rethinking Residue: Determining the Perceptual Continuum of Residue on FEES to Enable Better Measurement.

    PubMed

    Pisegna, Jessica M; Kaneoka, Asako; Leonard, Rebecca; Langmore, Susan E

    2018-02-01

    The goal of this work was to better understand perceptual judgments of pharyngeal residue on flexible endoscopic evaluation of swallowing (FEES) and the influence of a visual analog scale (VAS) versus an ordinal scale on clinician ratings. The intent was to determine if perceptual judgments of residue were more accurately described by equal or unequal intervals. Thirty-three speech language pathologists rated pharyngeal residue from 75 FEES videos representing a wide range of residue severities for thin liquid, applesauce, and cracker boluses. Clinicians rated their impression of the overall residue amount in each video on a VAS and, in a different session, on a five-point ordinal scale. Residue ratings were made in two separate sessions separated by several weeks. Statistical correlations of the two rating methods were carried out and best-fit models were determined for each bolus type. A total of 2475 VAS ratings and 2473 ordinal ratings were collected. Residue ratings from both methods (VAS and ordinal) were strongly correlated for all bolus types. The best fit for the data was a quadratic model representing unequal intervals, which significantly improved the r 2 values for each bolus type (cracker r 2  = 0.98, applesauce r 2  = 0.99, thin liquid r 2  = 0.98, all p < 0.0001). Perceptual ratings of pharyngeal residue demonstrated a statistical relationship consistent with unequal intervals. The present findings support the use of a VAS to rate residue on FEES, allowing for greater precision as compared to traditional ordinal rating scales. Perceptual judgments of pharyngeal residue reflected unequal intervals, an important concept that should be considered in future rating scales.

  8. Modeling the Residual Strength of a Fibrous Composite Using the Residual Daniels Function

    NASA Astrophysics Data System (ADS)

    Paramonov, Yu.; Cimanis, V.; Varickis, S.; Kleinhofs, M.

    2016-09-01

    The concept of a residual Daniels function (RDF) is introduced. Together with the concept of Daniels sequence, the RDF is used for estimating the residual (after some preliminary fatigue loading) static strength of a unidirectional fibrous composite (UFC) and its S-N curve on the bases of test data. Usually, the residual strength is analyzed on the basis of a known S-N curve. In our work, an inverse approach is used: the S-N curve is derived from an analysis of the residual strength. This approach gives a good qualitive description of the process of decreasing residual strength and explanes the existence of the fatigue limit. The estimates of parameters of the corresponding regression model can be interpreted as estimates of parameters of the local strength of components of the UFC. In order to approach the quantitative experimental estimates of the fatigue life, some ideas based on the mathematics of the semiMarkovian process are employed. Satisfactory results in processing experimental data on the fatigue life and residual strength of glass/epoxy laminates are obtained.

  9. 40 CFR 721.4500 - Isopropylamine distillation residues and ethylamine distillation residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Isopropylamine distillation residues and ethylamine distillation residues. 721.4500 Section 721.4500 Protection of Environment... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.4500 Isopropylamine distillation...

  10. 40 CFR 721.4500 - Isopropylamine distillation residues and ethylamine distillation residues.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Isopropylamine distillation residues and ethylamine distillation residues. 721.4500 Section 721.4500 Protection of Environment... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.4500 Isopropylamine distillation...

  11. 40 CFR 721.4500 - Isopropylamine distillation residues and ethylamine distillation residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Isopropylamine distillation residues and ethylamine distillation residues. 721.4500 Section 721.4500 Protection of Environment... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.4500 Isopropylamine distillation...

  12. 40 CFR 721.4500 - Isopropylamine distillation residues and ethylamine distillation residues.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Isopropylamine distillation residues and ethylamine distillation residues. 721.4500 Section 721.4500 Protection of Environment... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.4500 Isopropylamine distillation...

  13. 40 CFR 721.4500 - Isopropylamine distillation residues and ethylamine distillation residues.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Isopropylamine distillation residues and ethylamine distillation residues. 721.4500 Section 721.4500 Protection of Environment... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.4500 Isopropylamine distillation...

  14. Cell division and endoreduplication play important roles in stem swelling of tuber mustard (Brassica juncea Coss. var. tumida Tsen et Lee).

    PubMed

    Shi, H; Wang, L L; Sun, L T; Dong, L L; Liu, B; Chen, L P

    2012-11-01

    We investigated spatio-temporal variations in cell division and the occurrence of endoreduplication in cells of tuber mustard stems during development. Cells in the stem had 8C nuclei (C represents DNA content of a two haploid genome), since it is an allotetraploid species derived from diploid Brassica rapa (AA) and B. nigra (BB), thus indicating the occurrence of endoreduplication. Additionally, we observed a dynamic change of cell ploidy in different regions of the swollen stems, with a decrease in 4C proportion in P4-1 and a sharp increase in 8C cells that became the dominant cell type (86.33% at most) in the inner pith cells. Furthermore, cDNAs of 14 cell cycle genes and four cell expansion genes were cloned and their spatial transcripts analysed in order to understand their roles in stem development. The expression of most cell cycle genes peaked in regions of the outer pith (P2 or P3), some genes regulating S/G2 and G2/M (BjCDKB1;2, BjCYCB1;1 and BjCYCB1;2) significantly decrease in P5 and P6, while G1/S regulators (BjE2Fa, BjE2Fb and BjE2Fc) showed a relative high expression level in the inner pith (P5) where cells were undergoing endoreduplication. Coincidentally, BjXTH1and BjXTH2 were exclusively expressed in the endoreduplicated cells. Our results suggest that cells of outer pith regions (P2 and P3) mainly divide for cell proliferation, while cells of the inner pith expand through endoreduplication. Endoreduplication could trigger expression of BjXTH1 and BjXTH2 and thus function in cell expansion of the pith tissue. © 2012 German Botanical Society and The Royal Botanical Society of the Netherlands.

  15. Effects of shoot inversion on stem structure in Pharbitis nil

    NASA Technical Reports Server (NTRS)

    Prasad, T. K.; Sack, F. D.; Cline, M. G.

    1988-01-01

    The effects of shoot inversion on stem structure over 72 hr were investigated in Pharbitis nil by analyzing cell number, cell length, and the cross sectional areas of cells, tissues, and regions. An increase in stem diameter can be attributed to an increase in both cell number and cross sectional area of pith (primarily) and vascular tissue (secondarily). Qualitative observations of cell wall thickness in the light microscope did not reveal any significant effects of shoot inversion on this parameter. The inhibition of shoot elongation was accompanied by a significant decrease in cell length in the pith. The results are generally consistent with an ethylene effect on cell dimensions, especially in the pith.

  16. On tide-induced Lagrangian residual current and residual transport: 2. Residual transport with application in south San Francisco Bay, California

    USGS Publications Warehouse

    Feng, Shizuo; Cheng, Ralph T.; Pangen, Xi

    1986-01-01

    The transports of solutes and other tracers are fundamental to estuarine processes. The apparent transport mechanisms are convection by tidal current and current-induced shear effect dispersion for processes which take place in a time period of the order of a tidal cycle. However, as emphasis is shifted toward the effects of intertidal processes, the net transport is mainly determined by tide-induced residual circulation and by residual circulation due to other processes. The commonly used intertidal conservation equation takes the form of a convection-dispersion equation in which the convective velocity is the Eulerian residual current, and the dispersion terms are often referred to as the phase effect dispersion or, sometimes, as the “tidal dispersion.” The presence of these dispersion terms is merely the result of a Fickian type hypothesis. Since the actual processes are not Fickian, thus a Fickian hypothesis obscures the physical significance of this equation. Recent research results on residual circulation have suggested that long-term transport phenomena are closely related to the Lagrangian residual current or the Lagrangian residual transport. In this paper a new formulation of an intertidal conservation equation is presented and examined in detail. In a weakly nonlinear tidal estuary the resultant intertidal transport equation also takes the form of a convection-dispersion equation without the ad hoc introduction of phase effect dispersion in a form of dispersion tensor. The convective velocity in the resultant equation is the first-order Lagrangian residual current (the sum of the Eulerian residual current and the Stokes drift). The remaining dispersion terms are important only in higher-order solutions; they are due to shear effect dispersion and turbulent mixing. There exists a dispersion boundary layer adjacent to shoreline boundaries. An order of magnitude estimate of the properties in the dispersion boundary layer is given. The present treatment

  17. DOE Office of Scientific and Technical Information (OSTI.GOV)

    Tatsumi, Y.; Chachin, K.; Ogata, K.

    The purpose of the experiment was to determine the changes of o- diphenol, ascorbic acid, and activities of polyphenol oxidase and peroxidase, accompanied with the browning by the low dose of gamma ray, in three parts of tuber tissue (cortex, vascular bundle, and pith), and to observe the relation between the browning and the changes of ihose compounds and enzyme activities. The odiphenol content increased in irradiated tabers and the increasing rate was greater in cortex and vascular bundle than in pith. The ascorbic acid content decreased with higher doses, and the decreasing rate was greater in cortex and vascularmore » bundle than in pith. The activities of polyphenol oxidase and peroxidase also increased in irradiated tubers. The activity of polyphenol oxidase increased more in cortex than in vascular bundle and pith and the activity of peroxidase increased more in vascular bundle than in cortex and pith. ln the potato tubers in which irradiation was conducted immediately after harvest, the browning was induced within several days after irradiation. However, in the potato tubers in which irradiation was conducted about 3 months, the browning did not occur after irradiation. The former showed the increase of o-diphenol content and the activities of these enzymes, and the decrease of ascorbic acid content, the latter did not show the changes of o-diphenol and ascorbic acid and activities of the enzymes. (auth)« less

  18. Flexibility of active-site gorge aromatic residues and non-gorge aromatic residues in acetylcholinesterase

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Ghattyvenkatakrishna, Pavan K; Uberbacher, Edward C

    2013-01-01

    The presence of an unusually large number of aromatic residues in the active site gorge of acetylcholinesterase has been a topic of great interest. Flexibility of these residues has been suspected to be a key player in controlling ligand traversal in the gorge. This raises the question of whether the over representation of aromatic residues in the gorge implies higher than normal flexibility of those residues. The current study suggests that it does not. Large changes in the hydrophobic cross sectional area due to dihedral oscillations are probably the reason behind their presence in the gorge.

  19. Material Utilization of Organic Residues.

    PubMed

    Peinemann, Jan Christoph; Pleissner, Daniel

    2018-02-01

    Each year, 1.3 billion tons of food waste is generated globally. This waste traces back to industrial and agricultural producers, bakeries, restaurants, and households. Furthermore, lignocellulosic materials, including grass clippings, leaves, bushes, shrubs, and woods, appear in large amounts. Depending on the region, organic waste is either composted, burned directly, or converted into biogas. All of the options set aside the fact that organic residues are valuable resources containing carbohydrates, lipids, proteins, and phosphorus. Firstly, it is clear that avoidance of organic residues is imperative. However, the residues that accumulate nonetheless should be utilized by material means before energy production is targeted. This review presents different processes for the microbial utilization of organic residues towards compounds that are of great importance for the bioeconomy. The focus thereby is on the challenges coming along with downstream processing when the utilization of organic residues is carried out decentralized. Furthermore, a future process for producing lactic acid from organic residues is sketched.

  20. Identification of residue pairing in interacting β-strands from a predicted residue contact map.

    PubMed

    Mao, Wenzhi; Wang, Tong; Zhang, Wenxuan; Gong, Haipeng

    2018-04-19

    Despite the rapid progress of protein residue contact prediction, predicted residue contact maps frequently contain many errors. However, information of residue pairing in β strands could be extracted from a noisy contact map, due to the presence of characteristic contact patterns in β-β interactions. This information may benefit the tertiary structure prediction of mainly β proteins. In this work, we propose a novel ridge-detection-based β-β contact predictor to identify residue pairing in β strands from any predicted residue contact map. Our algorithm RDb 2 C adopts ridge detection, a well-developed technique in computer image processing, to capture consecutive residue contacts, and then utilizes a novel multi-stage random forest framework to integrate the ridge information and additional features for prediction. Starting from the predicted contact map of CCMpred, RDb 2 C remarkably outperforms all state-of-the-art methods on two conventional test sets of β proteins (BetaSheet916 and BetaSheet1452), and achieves F1-scores of ~ 62% and ~ 76% at the residue level and strand level, respectively. Taking the prediction of the more advanced RaptorX-Contact as input, RDb 2 C achieves impressively higher performance, with F1-scores reaching ~ 76% and ~ 86% at the residue level and strand level, respectively. In a test of structural modeling using the top 1 L predicted contacts as constraints, for 61 mainly β proteins, the average TM-score achieves 0.442 when using the raw RaptorX-Contact prediction, but increases to 0.506 when using the improved prediction by RDb 2 C. Our method can significantly improve the prediction of β-β contacts from any predicted residue contact maps. Prediction results of our algorithm could be directly applied to effectively facilitate the practical structure prediction of mainly β proteins. All source data and codes are available at http://166.111.152.91/Downloads.html or the GitHub address of https://github.com/wzmao/RDb2C .

  1. Residuals and the Residual-Based Statistic for Testing Goodness of Fit of Structural Equation Models

    ERIC Educational Resources Information Center

    Foldnes, Njal; Foss, Tron; Olsson, Ulf Henning

    2012-01-01

    The residuals obtained from fitting a structural equation model are crucial ingredients in obtaining chi-square goodness-of-fit statistics for the model. The authors present a didactic discussion of the residuals, obtaining a geometrical interpretation by recognizing the residuals as the result of oblique projections. This sheds light on the…

  2. Residue-residue contacts: application to analysis of secondary structure interactions.

    PubMed

    Potapov, Vladimir; Edelman, Marvin; Sobolev, Vladimir

    2013-01-01

    Protein structures and their complexes are formed and stabilized by interactions, both inside and outside of the protein. Analysis of such interactions helps in understanding different levels of structures (secondary, super-secondary, and oligomeric states). It can also assist molecular biologists in understanding structural consequences of modifying proteins and/or ligands. In this chapter, our definition of atom-atom and residue-residue contacts is described and applied to analysis of protein-protein interactions in dimeric β-sandwich proteins.

  3. Wood Residue Distribution Simulator (WORDS)

    Treesearch

    Douglas A. Eza; James W. McMinn; Peter E. Dress

    1984-01-01

    Successful development of woody biomass for energy will depend on the distribution of local supply and demand within subregions, rather than on the total inventory of residues. The Wood Residue Distribution Simulator (WORDS) attempts to find a least-cost allocation of residues from local sources of supply to local sources of demand, given the cost of the materials,...

  4. Microwave emission and crop residues

    NASA Technical Reports Server (NTRS)

    Jackson, Thomas J.; O'Neill, Peggy E.

    1991-01-01

    A series of controlled experiments were conducted to determine the significance of crop residues or stubble in estimating the emission of the underlying soil. Observations using truck-mounted L and C band passive microwave radiometers showed that for dry wheat and soybeans the dry residue caused negligible attenuation of the background emission. Green residues, with water contents typical of standing crops, did have a significant effect on the background emission. Results for these green residues also indicated that extremes in plant structure, as created using parallel and perpendicular stalk orientations, can cause very large differences in the degree of attenuation.

  5. Applications of bauxite residue: A mini-review.

    PubMed

    Verma, Ajay S; Suri, Narendra M; Kant, Suman

    2017-10-01

    Bauxite residue is the waste generated during alumina production by Bayer's process. The amount of bauxite residue (40-50 wt%) generated depends on the quality of bauxite ore used for the processing. High alkalinity and high caustic content in bauxite residue causes environmental risk for fertile soil and ground water contamination. The caustic (NaOH) content in bauxite residue leads to human health risks, like dermal problems and irritation to eyes. Moreover, disposal of bauxite residue requires a large area; such problems can only be minimised by utilising bauxite residue effectively. For two decades, bauxite residue has been used as a binder in cement industries and filler/reinforcement for composite materials in the automobile industry. Valuable metals and oxides, like alumina (Al 2 O 3 ), titanium oxide (TiO 2 ) and iron oxide Fe 2 O 3 , were extracted from bauxite residue to reduce waste. Bauxite residue was utilised in construction and structure industries to make geopolymers. It was also used in the making of glass-ceramics and a coating material. Recently bauxite residue has been utilised to extract rare earth elements like scandium (Sc), yttrium (Y), lanthanum (La), cerium (Ce), neodymium (Nd) and dysprosium (Dy). In this review article, the mineralogical characteristics of bauxite residue are summarised and current progresses on utilisation of bauxite residue in different fields of science and engineering are presented in detail.

  6. 40 CFR 180.123 - Inorganic bromide residues resulting from fumigation with methyl bromide; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... from fumigation with methyl bromide; tolerances for residues. 180.123 Section 180.123 Protection of... fumigation with methyl bromide; tolerances for residues. (a) General. (1) Tolerances are established for... on dog food, resulting from fumigation with methyl bromide. (ii) 125 parts per million for residues...

  7. Evaluation of sanitizers for inactivating Salmonella on in-shell pecans and pecan nutmeats.

    PubMed

    Beuchat, Larry R; Mann, David A; Alali, Walid Q

    2012-11-01

    Chlorine, organic acids, and water extracts of inedible pecan components were tested for effectiveness in killing Salmonella on pecans. In-shell pecans and nutmeats (U.S. Department of Agriculture medium pieces) were immersion inoculated with a mixture of five Salmonella serotypes, dried to 3.7% moisture, and stored at 4°C for 3 to 6 weeks. In-shell nuts were immersed in chlorinated water (200, 400, and 1,000 μg/ml), lactic acid (0.5, 1, and 2%), and levulinic acid (0.5, 1, and 2%) with and without 0.05% sodium dodecyl sulfate (SDS), and a mixed peroxyacid sanitizer (Tsunami 200, 40 μg/ml) for up to 20 min at 21°C. The rate of reduction of free chlorine in conditioning water decreased as the ratio of in-shell nuts/water was increased. The rate of reduction was more rapid when nuts were not precleaned before treatment. The initial population of Salmonella on in-shell nuts (5.9 to 6.3 log CFU/g) was reduced by 2.8 log CFU/g after treating with chlorinated water (1,000 μg/ml). Treatment with 2% lactic acid plus SDS or 2% levulinic acid plus SDS reduced the pathogen by 3.7 and 3.4 log CFU/g, respectively. Lactic and levulinic acids (2%) without SDS were less effective (3.3- and 2.1-log CFU/g reductions, respectively) than acids with SDS. Treatment with Tsunami 200 resulted in a 2.4-log CFU/g reduction. In-shell nuts and nutmeats were immersed in water extracts of ground pecan shucks (hulls), shells, a mixture of shells and pith, and pith. The general order of lethality of extracts to Salmonella was shuck < shell-pith ≤ shell ≤ pith < chlorine (400 μg/ml) and shuck < shell ≤ pith = shell-pith < chlorine (400 μg/ml). Results emphasize the importance of removing soil and dust on in-shell pecans before conditioning in chlorinated water and the need for sanitizers with increased effectiveness in killing Salmonella on pecans.

  8. Residual stress characterization of steel TIG welds by neutron diffraction and by residual magnetic stray field mappings

    NASA Astrophysics Data System (ADS)

    Stegemann, Robert; Cabeza, Sandra; Lyamkin, Viktor; Bruno, Giovanni; Pittner, Andreas; Wimpory, Robert; Boin, Mirko; Kreutzbruck, Marc

    2017-03-01

    The residual stress distribution of tungsten inert gas welded S235JRC+C plates was determined by means of neutron diffraction (ND). Large longitudinal residual stresses with maxima around 600 MPa were found. With these results as reference, the evaluation of residual stress with high spatial resolution GMR (giant magneto resistance) sensors was discussed. The experiments performed indicate a correlation between changes in residual stresses (ND) and the normal component of local residual magnetic stray fields (GMR). Spatial variations in the magnetic field strength perpendicular to the welds are in the order of the magnetic field of the earth.

  9. Improved crop residue cover estimates by coupling spectral indices for residue and moisture

    USDA-ARS?s Scientific Manuscript database

    Remote sensing assessment of soil residue cover (fR) and tillage intensity will improve our predictions of the impact of agricultural practices and promote sustainable management. Spectral indices for estimating fR are sensitive to soil and residue water content, therefore, the uncertainty of estima...

  10. Heavy metal bioaccumulation in Great Basin submersed aquatic macrophytes

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Lytle, C.M.

    1994-01-01

    Seasonal element cycling and nutritional quality were determined in sago pondweed plant tissue. Leaf protein was 27% in July and 15% in December. Sago drupelet protein content was 9% in July and 6.5% in October. Sago plant tissue mineral, trace metal and non-structural carbohydrate content were high in the Fall. Submersed aquatic plant species from the Provo River drainage, Bear River MBR and Utah Lake - Provo Bay were significantly higher in heavy metals than aquatic species from remote wetlands. Extreme sodium concentrations were found in water, sediment and plant tissue in Ibis and Harrison pools (Fish Springs NWR). Boron,more » arsenic and selenium concentrations in plant tissue were much lower than those at Kesterson Reservoir, California. Submersed aquatic plants may act as channels that expedite the trophic movement of metal ions. The chemical structure of accumulated manganese and iron in sago pondweed plant tissue differed with time of year. June plant tissue manganese was fully hydrated. Accumulated manganese in October plant tissue was a Mn(II)Mn(III) mineral oxide. Accumulated iron was Fe(III) in both leaf and root tissue. Methylmercury was toxic to Lesser duckweed at very low doses (>0.1 [mu]g ml[sup [minus]1]). Increased pH improved frond survival in organic and inorganic mercury solutions. Duckweed should be considered as a sensitive phytoassay of methylmercury toxicity. Soil manganese and lead concentrations are correlated with distance from the roadway and traffic volume. Soil lead concentrations have moved deeper into the profile. Roadside aquatic plants were higher in manganese than herbaceous plants and grasses. Roadside snow and water were low in manganese and lead. Roadside soil and plants were apparently contaminated by Mn oxides from motor vehicle exhaust.« less

  11. Residual Structures in Latent Growth Curve Modeling

    ERIC Educational Resources Information Center

    Grimm, Kevin J.; Widaman, Keith F.

    2010-01-01

    Several alternatives are available for specifying the residual structure in latent growth curve modeling. Two specifications involve uncorrelated residuals and represent the most commonly used residual structures. The first, building on repeated measures analysis of variance and common specifications in multilevel models, forces residual variances…

  12. 40 CFR 158.2290 - Residue chemistry.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 24 2014-07-01 2014-07-01 false Residue chemistry. 158.2290 Section... REQUIREMENTS FOR PESTICIDES Antimicrobial Pesticide Data Requirements § 158.2290 Residue chemistry. (a) General... determine the residue chemistry data requirements for antimicrobial pesticide products. Notes that apply to...

  13. 40 CFR 158.2290 - Residue chemistry.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 25 2013-07-01 2013-07-01 false Residue chemistry. 158.2290 Section... REQUIREMENTS FOR PESTICIDES Antimicrobial Pesticide Data Requirements § 158.2290 Residue chemistry. (a) General... determine the residue chemistry data requirements for antimicrobial pesticide products. Notes that apply to...

  14. Characterisation and management of concrete grinding residuals.

    PubMed

    Kluge, Matt; Gupta, Nautasha; Watts, Ben; Chadik, Paul A; Ferraro, Christopher; Townsend, Timothy G

    2018-02-01

    Concrete grinding residue is the waste product resulting from the grinding, cutting, and resurfacing of concrete pavement. Potential beneficial applications for concrete grinding residue include use as a soil amendment and as a construction material, including as an additive to Portland cement concrete. Concrete grinding residue exhibits a high pH, and though not hazardous, it is sufficiently elevated that precautions need to be taken around aquatic ecosystems. Best management practices and state regulations focus on reducing the impact on such aquatic environment. Heavy metals are present in concrete grinding residue, but concentrations are of the same magnitude as typically recycled concrete residuals. The chemical composition of concrete grinding residue makes it a useful product for some soil amendment purposes at appropriate land application rates. The presence of unreacted concrete in concrete grinding residue was examined for potential use as partial replacement of cement in new concrete. Testing of Florida concrete grinding residue revealed no dramatic reactivity or improvement in mortar strength.

  15. 48 CFR 50.104 - Residual powers.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Residual powers. 50.104... EXTRAORDINARY CONTRACTUAL ACTIONS AND THE SAFETY ACT Extraordinary Contractual Actions 50.104 Residual powers. This section prescribes standards and procedures for exercising residual powers under Pub. L. 85-804...

  16. 48 CFR 50.104 - Residual powers.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 1 2011-10-01 2011-10-01 false Residual powers. 50.104... EXTRAORDINARY CONTRACTUAL ACTIONS AND THE SAFETY ACT Extraordinary Contractual Actions 50.104 Residual powers. This section prescribes standards and procedures for exercising residual powers under Pub. L. 85-804...

  17. Residual stresses in welded plates

    NASA Technical Reports Server (NTRS)

    Bernstein, Edward L.

    1994-01-01

    The purpose of this project was to develop a simple model which could be used to study residual stress. The mechanism that results in residual stresses in the welding process starts with the deposition of molten weld metal which heats the immediately adjacent material. After solidification of weld material, normal thermal shrinkage is resisted by the adjacent, cooler material. When the thermal strain exceeds the elastic strain corresponding to the yield point stress, the stress level is limited by this value, which decreases with increasing temperature. Cooling then causes elastic unloading which is restrained by the adjoining material. Permanent plastic strain occurs, and tension is caused in the region immediately adjacent to the weld material. Compression arises in the metal farther from the weld in order to maintain overall static equilibrium. Subsequent repair welds may add to the level of residual stresses. The level of residual stress is related to the onset of fracture during welding. Thus, it is of great importance to be able to predict the level of residual stresses remaining after a weld procedure, and to determine the factors, such as weld speed, temperature, direction, and number of passes, which may affect the magnitude of remaining residual stress. It was hoped to use traditional analytical modeling techniques so that it would be easier to comprehend the effect of these variables on the resulting stress. This approach was chosen in place of finite element methods so as to facilitate the understanding of the physical processes. The accuracy of the results was checked with some existing experimental studies giving residual stress levels found from x-ray diffraction measurements.

  18. Residual stress at fluid interfaces

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Murray, P.E.

    We extend the Navier-Stokes equations to allow for residual stress in Newtonian fluids. A fluid, which undergoes a constrained volume change, will have residual stress. Corresponding to every constrained volume change is an eigenstrain. We present a method to include in the equations of fluid motion the eigenstrain that is a result of the presence in a fluid of a soluble chemical species. This method is used to calculate the residual stress associated with a chemical transformation. 9 refs., 1 fig.

  19. Particulate residue separators for harvesting devices

    DOEpatents

    Hoskinson, Reed L.; Kenney, Kevin L.; Wright, Christopher T.; Hess, John R.

    2010-06-29

    A particulate residue separator and a method for separating a particulate residue stream may include a plenum borne by a harvesting device, and have a first, intake end and a second, exhaust end; first and second particulate residue air streams which are formed by the harvesting device and which travel, at least in part, along the plenum and in a direction of the second, exhaust end; and a baffle assembly which is located in partially occluding relation relative to the plenum, and which substantially separates the first and second particulate residue air streams.

  20. Identification of kinetically hot residues in proteins.

    PubMed Central

    Demirel, M. C.; Atilgan, A. R.; Jernigan, R. L.; Erman, B.; Bahar, I.

    1998-01-01

    A number of recent studies called attention to the presence of kinetically important residues underlying the formation and stabilization of folding nuclei in proteins, and to the possible existence of a correlation between conserved residues and those participating in the folding nuclei. Here, we use the Gaussian network model (GNM), which recently proved useful in describing the dynamic characteristics of proteins for identifying the kinetically hot residues in folded structures. These are the residues involved in the highest frequency fluctuations near the native state coordinates. Their high frequency is a manifestation of the steepness of the energy landscape near their native state positions. The theory is applied to a series of proteins whose kinetically important residues have been extensively explored: chymotrypsin inhibitor 2, cytochrome c, and related C2 proteins. Most of the residues previously pointed out to underlie the folding process of these proteins, and to be critically important for the stabilization of the tertiary fold, are correctly identified, indicating a correlation between the kinetic hot spots and the early forming structural elements in proteins. Additionally, a strong correlation between kinetically hot residues and loci of conserved residues is observed. Finally, residues that may be important for the stability of the tertiary structure of CheY are proposed. PMID:9865946

  1. Disposal of bridge paint residue.

    DOT National Transportation Integrated Search

    2005-12-01

    Paint residue generated by bridge maintenance painting commonly contains lead requiring the residue to be disposed of as a hazardous waste. Several alternatives are being investigated in this study, chemical stabilization and recycling as options for...

  2. Utilization of oak residues

    Treesearch

    Richard C. Allison

    1971-01-01

    Residues should be thought of as a raw material for specific uses rather than as a waste. Fines and solid wood residues are usually kept separated in waste-collection system, but species are rarely kept separated. The properties of each species dictate what uses can be made of them. Quantity, location, cost, moisture content, physical size, and presence of foreign...

  3. Axial residual stresses in boron fibers

    NASA Technical Reports Server (NTRS)

    Behrendt, D. R.

    1978-01-01

    The axial residual stress distribution as a function of radius was determined from the fiber surface to the core including the average residual stress in the core. Such measurements on boron on tungsten (B/W) fibers show that the residual stresses for 102, 142, 203, and 366 micron diameter fibers were similar, being compressive at the surface and changing monotonically to a region of tensile within the boron. At approximately 25 percent of the original radius, the stress reaches a maximum tensile stress of about 860 mn/sq.m and then decreases to a compressive stress near the tungsten boride core. Data were presented for 203 micron diameter B/W fibers that show annealing above 900 C reduces the residual stresses. A comparison between 102 micron diameter B/W and boron on carbon (b/C) shows that the residual stresses were similar in the outer regions of the fibers, but that large differences near and in the core were observed. The effects of these residual stresses on the fracture of boron fibers were discussed.

  4. Determination of Pesticides Residues in Cucumbers Grown in Greenhouse and the Effect of Some Procedures on Their Residues.

    PubMed

    Leili, Mostafa; Pirmoghani, Amin; Samadi, Mohammad Taghi; Shokoohi, Reza; Roshanaei, Ghodratollah; Poormohammadi, Ali

    2016-11-01

    The objective of this study was to determine the residual concentrations of ethion and imidacloprid in cucumbers grown in greenhouse. The effect of some simple processing procedures on both ethion and imidacloprid residues were also studied. Ten active greenhouses that produce cucumber were randomly selected. Ethion and imidacloprid as the most widely used pesticides were measured in cucumber samples of studied greenhouses. Moreover, the effect of storing, washing, and peeling as simple processing procedures on both ethion and imidacloprid residues were investigated. One hour after pesticide application; the maximum residue levels (MRLs) of ethion and imidacloprid were higher than that of Codex standard level. One day after pesticide application, the levels of pesticides were decreased about 35 and 31% for ethion and imidacloprid, respectively, which still were higher than the MRL. Washing procedure led to about 51 and 42.5% loss in ethion and imidacloprid residues, respectively. Peeling procedure also led to highest loss of 93.4 and 63.7% in ethion and imidacloprid residues, respectively. The recovery for both target analytes was in the range between 88 and 102%. The residue values in collected samples one hour after pesticides application were higher than standard value. The storing, washing, and peeling procedures lead to the decrease of pesticide residues in greenhouse cucumbers. Among them, the peeling procedure has the greatest impact on residual reduction. Therefore, these procedures can be used as simple and effective processing techniques for reducing and removing pesticides from greenhouse products before their consumption.

  5. Managing residual limb hyperhidrosis in wounded warriors.

    PubMed

    Pace, Sarah; Kentosh, Joshua

    2016-06-01

    Residual limb dermatologic problems are a common concern among young active traumatic amputee patients who strive to maintain an active lifestyle. Hyperhidrosis of residual limbs is a recognized inciting factor that often contributes to residual limb dermatoses and is driven by the design of the prosthetic liner covering the residual limb. Treatment of hyperhidrosis in this population presents a unique challenge. Several accepted treatments of hyperhidrosis can offer some relief but have been limited by lack of results or side-effect profiles. Microwave thermal ablation has presented an enticing potential for residual limb hyperhidrosis.

  6. Residues of azoxystrobin from grapes to raisins.

    PubMed

    Lentza-Rizos, Chaido; Avramides, Elizabeth J; Kokkinaki, Kalliopi

    2006-01-11

    Azoxystrobin, a fungicide of the strobilurin group, has an European Union maximum residue level (MRL) of 2 mg/kg for grapes. This work aimed to assess residues on fresh and washed grapes and on raisins following processing with (i) alkali treatment and sun drying and (ii) sun drying only. QUADRIS 25% SC was applied according to good agricultural practice for two consecutive years on a typical cv. Thomson seedless and a seed-producing clone. Samples were collected 0, 15, and 21 days postapplication and analyzed using gas chromatography/electron capture detection; recoveries were 86 +/- 12% for grapes and 99 +/- 15% for raisins. Residues on grapes were 0.49-1.84 mg/kg, and washing removed 75% of the residue. Residues in raisins produced from seedless grapes were 0.51-1.49 (treatment 1) and 1.42-2.08 mg/kg (treatment 2), with residue transfer factors sometimes >1, even following alkali treatment, which reduced residues considerably. To avoid trade problems, a higher MRL for raisins is necessary.

  7. Agricultural residue availability in the United States.

    PubMed

    Haq, Zia; Easterly, James L

    2006-01-01

    The National Energy Modeling System (NEMS) is used by the Energy Information Administration (EIA) to forecast US energy production, consumption, and price trends for a 25-yr-time horizon. Biomass is one of the technologies within NEMS, which plays a key role in several scenarios. An endogenously determined biomass supply schedule is used to derive the price-quantity relationship of biomass. There are four components to the NEMS biomass supply schedule including: agricultural residues, energy crops, forestry residues, and urban wood waste/mill residues. The EIA's Annual Energy Outlook 2005 includes updated estimates of the agricultural residue portion of the biomass supply schedule. The changes from previous agricultural residue supply estimates include: revised assumptions concerning corn stover and wheat straw residue availabilities, inclusion of non-corn and non-wheat agricultural residues (such as barley, rice straw, and sugarcane bagasse), and the implementation of assumptions concerning increases in no-till farming. This article will discuss the impact of these changes on the supply schedule.

  8. Methods of separating particulate residue streams

    DOEpatents

    Hoskinson, Reed L [Rigby, ID; Kenney, Kevin L [Idaho Falls, ID; Wright, Christopher T [Idaho Falls, ID; Hess, J Richard [Idaho Falls, ID

    2011-04-05

    A particulate residue separator and a method for separating a particulate residue stream may include an air plenum borne by a harvesting device, and have a first, intake end and a second, exhaust end; first and second particulate residue air streams that are formed by the harvesting device and that travel, at least in part, along the air plenum and in a direction of the second, exhaust end; and a baffle assembly that is located in partially occluding relation relative to the air plenum and that substantially separates the first and second particulate residue air streams.

  9. Residual Cap

    NASA Image and Video Library

    2006-05-10

    This MOC image shows a summertime view of the south polar residual cap of Mars. In this image, mesas composed largely of solid carbon dioxide are separated from one another by irregularly-shaped depressions

  10. Lamination residual stresses in hybrid composites, part 1

    NASA Technical Reports Server (NTRS)

    Daniel, I. M.; Liber, T.

    1976-01-01

    An experimental investigation was conducted to study lamination residual stresses for various material and loading parameters. The effects of hybridization on residual stresses and residual properties after thermal cycling under load were determined in angle-ply graphite/Kevlar/epoxy and graphite/S-glass/epoxy laminates. Residual strains in the graphite plies are not appreciably affected by the type and number of hybridizing plies. Computed residual stresses at room temperature in the S-glass plies reach values up to seventy-five percent of the transverse strength of the material. Computed residual stresses in the graphite plies exceed the static strength by approximately ten percent. In the case of Kevlar plies, computed residual stresses far exceed the static strength indicating possible early failure of these plies. Static testing of the hybrids above indicates that failure is governed by the ultimate strain of the graphite plies. In thermally cycled hybrids, in general, residual moduli were somewhat lower and residual strengths were higher than initial values.

  11. Distribution of Penicillin G Residues in Culled Dairy Cow Muscles: Implications for Residue Monitoring

    USDA-ARS?s Scientific Manuscript database

    The U.S. Food and Drug Administration sets tolerances for veterinary drug residues in muscle, but does not specify which type of muscle should be analyzed. In order to determine if antibiotic residue levels are dependent on muscle type, 7 culled dairy cows were dosed with Penicillin G (Pen G) from ...

  12. Environmental dredging residual generation and management.

    PubMed

    Patmont, Clay; LaRosa, Paul; Narayanan, Raghav; Forrest, Casey

    2018-05-01

    The presence and magnitude of sediment contamination remaining in a completed dredge area can often dictate the success of an environmental dredging project. The need to better understand and manage this remaining contamination, referred to as "postdredging residuals," has increasingly been recognized by practitioners and investigators. Based on recent dredging projects with robust characterization programs, it is now understood that the residual contamination layer in the postdredging sediment comprises a mixture of contaminated sediments that originate from throughout the dredge cut. This mixture of contaminated sediments initially exhibits fluid mud properties that can contribute to sediment transport and contamination risk outside of the dredge area. This article reviews robust dredging residual evaluations recently performed in the United States and Canada, including the Hudson River, Lower Fox River, Ashtabula River, and Esquimalt Harbour, along with other projects. These data better inform the understanding of residuals generation, leading to improved models of dredging residual formation to inform remedy evaluation, selection, design, and implementation. Data from these projects confirm that the magnitude of dredging residuals is largely determined by site conditions, primarily in situ sediment fluidity or liquidity as measured by dry bulk density. While the generation of dredging residuals cannot be avoided, residuals can be successfully and efficiently managed through careful development and implementation of site-specific management plans. Integr Environ Assess Manag 2018;14:335-343. © 2018 The Authors. Integrated Environmental Assessment and Management Published by Wiley Periodicals, Inc. on behalf of Society of Environmental Toxicology & Chemistry (SETAC). © 2018 The Authors. Integrated Environmental Assessment and Management Published by Wiley Periodicals, Inc. on behalf of Society of Environmental Toxicology & Chemistry (SETAC).

  13. 40 CFR 240.208 - Residue.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Residue. 240.208 Section 240.208 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES GUIDELINES FOR THE THERMAL PROCESSING OF SOLID WASTES Requirements and Recommended Procedures § 240.208 Residue. ...

  14. Prediction of interface residue based on the features of residue interaction network.

    PubMed

    Jiao, Xiong; Ranganathan, Shoba

    2017-11-07

    Protein-protein interaction plays a crucial role in the cellular biological processes. Interface prediction can improve our understanding of the molecular mechanisms of the related processes and functions. In this work, we propose a classification method to recognize the interface residue based on the features of a weighted residue interaction network. The random forest algorithm is used for the prediction and 16 network parameters and the B-factor are acting as the element of the input feature vector. Compared with other similar work, the method is feasible and effective. The relative importance of these features also be analyzed to identify the key feature for the prediction. Some biological meaning of the important feature is explained. The results of this work can be used for the related work about the structure-function relationship analysis via a residue interaction network model. Copyright © 2017 Elsevier Ltd. All rights reserved.

  15. Computational Prediction of Hot Spot Residues

    PubMed Central

    Morrow, John Kenneth; Zhang, Shuxing

    2013-01-01

    Most biological processes involve multiple proteins interacting with each other. It has been recently discovered that certain residues in these protein-protein interactions, which are called hot spots, contribute more significantly to binding affinity than others. Hot spot residues have unique and diverse energetic properties that make them challenging yet important targets in the modulation of protein-protein complexes. Design of therapeutic agents that interact with hot spot residues has proven to be a valid methodology in disrupting unwanted protein-protein interactions. Using biological methods to determine which residues are hot spots can be costly and time consuming. Recent advances in computational approaches to predict hot spots have incorporated a myriad of features, and have shown increasing predictive successes. Here we review the state of knowledge around protein-protein interactions, hot spots, and give an overview of multiple in silico prediction techniques of hot spot residues. PMID:22316154

  16. Dissipation and residue of myclobutanil in lychee.

    PubMed

    Liu, Yanping; Sun, Haibin; Liu, Fengmao; Wang, Siwei

    2012-06-01

    The dissipation and residue of myclobutanil in lychee under field conditions were studied. To determine myclobutanil residue in samples, an analytical method with a florisil column clean-up and detected by gas chromatography-electron capture detector (GC-ECD) was developed. Recoveries were found in the range of 83.24 %-89.00 % with relative standard deviations of 2.67 %-9.88 %. This method was successfully applied to analyze the dissipation and residue of myclobutanil in lychee in Guangdong and Guangxi Province, China. The half lives in lychee were from 2.2 to 3.4 days. The residues of myclobutanil in lychee flesh were all below the limit of quantification (LOQ) value (0.01 mg/kg), and most of the residues were concentrated in the peel. The terminal residues of myclobutanil were all bellow the maximum residue limit (MRL) value set by European Union (EU) (0.02 mg/kg). Hence it was safe for the use of this pesticide and the results also could give a reference for MRL setting of myclobutanil in lychee in China.

  17. Frequency behavior of the residual current devices

    NASA Astrophysics Data System (ADS)

    Erdei, Z.; Horgos, M.; Lung, C.; Pop-Vadean, A.; Muresan, R.

    2017-01-01

    This paper presents an experimental investigation into the operating characteristic of residual current devices when in presence of a residual current at a frequency of 60Hz. In order to protect persons and equipment effectively the residual current devices are made to be very sensitive to the ground fault current or the touch current. Because of their high sensitivity the residual current circuit breakers are prone to tripping under no-fault conditions.

  18. Prediction of residue-residue contact matrix for protein-protein interaction with Fisher score features and deep learning.

    PubMed

    Du, Tianchuan; Liao, Li; Wu, Cathy H; Sun, Bilin

    2016-11-01

    Protein-protein interactions play essential roles in many biological processes. Acquiring knowledge of the residue-residue contact information of two interacting proteins is not only helpful in annotating functions for proteins, but also critical for structure-based drug design. The prediction of the protein residue-residue contact matrix of the interfacial regions is challenging. In this work, we introduced deep learning techniques (specifically, stacked autoencoders) to build deep neural network models to tackled the residue-residue contact prediction problem. In tandem with interaction profile Hidden Markov Models, which was used first to extract Fisher score features from protein sequences, stacked autoencoders were deployed to extract and learn hidden abstract features. The deep learning model showed significant improvement over the traditional machine learning model, Support Vector Machines (SVM), with the overall accuracy increased by 15% from 65.40% to 80.82%. We showed that the stacked autoencoders could extract novel features, which can be utilized by deep neural networks and other classifiers to enhance learning, out of the Fisher score features. It is further shown that deep neural networks have significant advantages over SVM in making use of the newly extracted features. Copyright © 2016. Published by Elsevier Inc.

  19. 40 CFR 180.637 - Mandipropamid; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 24 2011-07-01 2011-07-01 false Mandipropamid; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.637 Mandipropamid; tolerances for residues. (a) General. Tolerances are established for residues...

  20. Radiocarbon Dating of an Olive Tree Cross-Section: New Insights on Growth Patterns and Implications for Age Estimation of Olive Trees.

    PubMed

    Ehrlich, Yael; Regev, Lior; Kerem, Zohar; Boaretto, Elisabetta

    2017-01-01

    The age of living massive olive trees is often assumed to be between hundreds and even thousands of years. These estimations are usually based on the girth of the trunk and an extrapolation based on a theoretical annual growth rate. It is difficult to objectively verify these claims, as a monumental tree may not be cut down for analysis of its cross-section. In addition, the inner and oldest part of the trunk in olive trees usually rots, precluding the possibility of carting out radiocarbon analysis of material from the first years of life of the tree. In this work we present a cross-section of an olive tree, previously estimated to be hundreds of years old, which was cut down post-mortem in 2013. The cross-section was radiocarbon dated at numerous points following the natural growth pattern, which was made possible to observe by viewing the entire cross-section. Annual growth rate values were calculated and compared between different radii. The cross-section also revealed a nearly independent segment of growth, which would clearly offset any estimations based solely on girth calculations. Multiple piths were identified, indicating the beginning of branching within the trunk. Different radii were found to have comparable growth rates, resulting in similar estimates dating the piths to the 19th century. The estimated age of the piths represent a terminus ante quem for the age of the tree, as these are piths of separate branches. However, the tree is likely not many years older than the dated piths, and certainly not centuries older. The oldest radiocarbon-datable material in this cross-section was less than 200 years old, which is in agreement with most other radiocarbon dates of internal wood from living olive trees, rarely older than 300 years.

  1. 40 CFR 180.315 - Methamidophos; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Methamidophos; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.315 Methamidophos; tolerances for residues. (a) Tolerances are established for residues of the...

  2. 40 CFR 180.425 - Clomazone; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 24 2011-07-01 2011-07-01 false Clomazone; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.425 Clomazone; tolerances for residues. (a) General. Tolerances are established for residues of...

  3. 40 CFR 180.601 - Cyazofamid; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 24 2011-07-01 2011-07-01 false Cyazofamid; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.601 Cyazofamid; tolerances for residues. (a) General. Tolerances are established for residues of...

  4. 40 CFR 180.478 - Rimsulfuron; tolerances for residues

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 24 2011-07-01 2011-07-01 false Rimsulfuron; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.478 Rimsulfuron; tolerances for residues (a) General. Tolerances are established for residues of...

  5. 40 CFR 180.433 - Fomesafen; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 24 2011-07-01 2011-07-01 false Fomesafen; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.433 Fomesafen; tolerances for residues. (a) General. Tolerances are established for residues of...

  6. 40 CFR 180.627 - Fluopicolide; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 24 2011-07-01 2011-07-01 false Fluopicolide; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.627 Fluopicolide; tolerances for residues. (a) General. Tolerances are established for residues of...

  7. 40 CFR 180.603 - Dinotefuran; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 24 2011-07-01 2011-07-01 false Dinotefuran; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.603 Dinotefuran; tolerances for residues. (a) General. (1) Tolerances are established for residues...

  8. 40 CFR 180.517 - Fipronil; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 24 2011-07-01 2011-07-01 false Fipronil; tolerances for residues. 180... PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.517 Fipronil; tolerances for residues. (a) General. Therefore, tolerances are established for combined residues...

  9. 40 CFR 180.261 - Phosmet; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 24 2011-07-01 2011-07-01 false Phosmet; tolerances for residues. 180... PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.261 Phosmet; tolerances for residues. (a) General. Tolerances are established for residues of the insecticide...

  10. 40 CFR 180.503 - Cymoxanil, tolerance for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 24 2011-07-01 2011-07-01 false Cymoxanil, tolerance for residues. 180... PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.503 Cymoxanil, tolerance for residues. (a) General. Tolerances are established for residues of the fungicide...

  11. 40 CFR 180.567 - Zoxamide; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 24 2011-07-01 2011-07-01 false Zoxamide; tolerances for residues. 180... PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.567 Zoxamide; tolerances for residues. (a) General. (1) Tolerances are established for residues of zoxamide (3...

  12. 40 CFR 180.567 - Zoxamide; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Zoxamide; tolerances for residues. 180... PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.567 Zoxamide; tolerances for residues. (a) General. (1) Tolerances are established for residues of zoxamide (3...

  13. 40 CFR 180.413 - Imazalil; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.413 Imazalil; tolerances for residues. (a) General. (1) Tolerances are established for the combined residues of..., hay 0.5 Wheat, straw 0.5 (2) Tolerances are established for the combined residues of the fungicide...

  14. DOE Office of Scientific and Technical Information (OSTI.GOV)

    Lagrimini, L.M.

    Tobacco (Nicotiana tabacum) plants transformed with a chimeric tobacco anionic peroxidase gene have previously been shown to synthesize high levels of peroxidase in all tissues throughout the plant. One of several distinguishable phenotypes of transformed plants is the rapid browning of pith tissue upon wounding. Pith tissue from plants expressing high levels of peroxidase browned within 24 hours of wounding, while tissue from control plants did not brown as late as 7 days after wounding. A correlation between peroxidase activity and wound-induced browning was observed, whereas no relationship between polyphenol oxidase activity and browning was found. The purified tobacco anionicmore » peroxidase was subjected to kinetic analysis with substrates which resemble the precursors of lignin or polyphenolic acid. The purified enzyme was found to readily polymerize phenolic acids in the presence of H{sub 2}O{sub 2} via a modified ping-pong mechanism. The percentage of lignin and lignin-related polymers in cell walls was nearly twofold greater in pith tissue isolated from peroxidase-overproducer plants compared to control plants. Lignin deposition in wounded pith tissue from control plants closely followed the induction of peroxidase activity. However, wound-induced lignification occurred 24 to 48 hours sooner in plants overexpressing the anionic peroxidase. This suggests that the availability of peroxidase rather than substrate may delay polyphenol deposition in wounded tissue.« less

  15. Wound-Induced Deposition of Polyphenols in Transgenic Plants Overexpressing Peroxidase 1

    PubMed Central

    Lagrimini, L. Mark

    1991-01-01

    Tobacco (Nicotiana tabacum) plants transformed with a chimeric tobacco anionic peroxidase gene have previously been shown to synthesize high levels of peroxidase in all tissues throughout the plant. One of several distinguishable phenotypes of transformed plants is the rapid browning of pith tissue upon wounding. Pith tissue from plants expressing high levels of peroxidase browned within 24 hours of wounding, while tissue from control plants did not brown as late as 7 days after wounding. A correlation between peroxidase activity and wound-induced browning was observed, whereas no relationship between polyphenol oxidase activity and browning was found. The purified tobacco anionic peroxidase was subjected to kinetic analysis with substrates which resemble the precursors of lignin or polyphenolic acid. The purified enzyme was found to readily polymerize phenolic acids in the presence of H2O2 via a modified ping-pong mechanism. The percentage of lignin and lignin-related polymers in cell walls was nearly twofold greater in pith tissue isolated from peroxidase-overproducer plants compared to control plants. Lignin deposition in wounded pith tissue from control plants closely followed the induction of peroxidase activity. However, wound-induced lignification occurred 24 to 48 hours sooner in plants overexpressing the anionic peroxidase. This suggests that the availability of peroxidase rather than substrate may delay polyphenol deposition in wounded tissue. ImagesFigure 1Figure 2Figure 3 PMID:16668224

  16. RESIDUAL RISK ASSESSMENT: ETHYLENE OXIDE ...

    EPA Pesticide Factsheets

    This document describes the residual risk assessment for the Ethylene Oxide Commercial Sterilization source category. For stationary sources, section 112 (f) of the Clean Air Act requires EPA to assess risks to human health and the environment following implementation of technology-based control standards. If these technology-based control standards do not provide an ample margin of safety, then EPA is required to promulgate addtional standards. This document describes the methodology and results of the residual risk assessment performed for the Ethylene Oxide Commercial Sterilization source category. The results of this analyiss will assist EPA in determining whether a residual risk rule for this source category is appropriate.

  17. RESIDUAL RISK ASSESSMENT: MAGNETIC TAPE ...

    EPA Pesticide Factsheets

    This document describes the residual risk assessment for the Magnetic Tape Manufacturing source category. For stationary sources, section 112 (f) of the Clean Air Act requires EPA to assess risks to human health and the environment following implementation of technology-based control standards. If these technology-based control standards do not provide an ample margin of safety, then EPA is required to promulgate addtional standards. This document describes the methodology and results of the residual risk assessment performed for the Magnetic Tape Manufacturing source category. The results of this analyiss will assist EPA in determining whether a residual risk rule for this source category is appropriate.

  18. 7 CFR 29.427 - Pesticide residue standards.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 2 2011-01-01 2011-01-01 false Pesticide residue standards. 29.427 Section 29.427... REGULATIONS TOBACCO INSPECTION Regulations Miscellaneous § 29.427 Pesticide residue standards. The maximum concentration of residues of the following pesticides allowed in flue-cured or burley tobacco, expressed as...

  19. 7 CFR 29.427 - Pesticide residue standards.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 2 2013-01-01 2013-01-01 false Pesticide residue standards. 29.427 Section 29.427... REGULATIONS TOBACCO INSPECTION Regulations Miscellaneous § 29.427 Pesticide residue standards. The maximum concentration of residues of the following pesticides allowed in flue-cured or burley tobacco, expressed as...

  20. 7 CFR 29.427 - Pesticide residue standards.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 2 2014-01-01 2014-01-01 false Pesticide residue standards. 29.427 Section 29.427... REGULATIONS TOBACCO INSPECTION Regulations Miscellaneous § 29.427 Pesticide residue standards. The maximum concentration of residues of the following pesticides allowed in flue-cured or burley tobacco, expressed as...

  1. 7 CFR 29.427 - Pesticide residue standards.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 2 2012-01-01 2012-01-01 false Pesticide residue standards. 29.427 Section 29.427... REGULATIONS TOBACCO INSPECTION Regulations Miscellaneous § 29.427 Pesticide residue standards. The maximum concentration of residues of the following pesticides allowed in flue-cured or burley tobacco, expressed as...

  2. 7 CFR 29.427 - Pesticide residue standards.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Pesticide residue standards. 29.427 Section 29.427... REGULATIONS TOBACCO INSPECTION Regulations Miscellaneous § 29.427 Pesticide residue standards. The maximum concentration of residues of the following pesticides allowed in flue-cured or burley tobacco, expressed as...

  3. Fluorescence imaging to quantify crop residue cover

    NASA Technical Reports Server (NTRS)

    Daughtry, C. S. T.; Mcmurtrey, J. E., III; Chappelle, E. W.

    1994-01-01

    Crop residues, the portion of the crop left in the field after harvest, can be an important management factor in controlling soil erosion. Methods to quantify residue cover are needed that are rapid, accurate, and objective. Scenes with known amounts of crop residue were illuminated with long wave ultraviolet (UV) radiation and fluorescence images were recorded with an intensified video camera fitted with a 453 to 488 nm band pass filter. A light colored soil and a dark colored soil were used as background for the weathered soybean stems. Residue cover was determined by counting the proportion of the pixels in the image with fluorescence values greater than a threshold. Soil pixels had the lowest gray levels in the images. The values of the soybean residue pixels spanned nearly the full range of the 8-bit video data. Classification accuracies typically were within 3(absolute units) of measured cover values. Video imaging can provide an intuitive understanding of the fraction of the soil covered by residue.

  4. Analysis of the Angle of Maximal Stability and Flow Regime Transitions in Different Proportions of Bi-phasic Granular Matter Mixtures

    NASA Astrophysics Data System (ADS)

    Maquiling, Joel Tiu; Visaga, Shane Marie

    This study investigates the dependence of the critical angle θc of stability on different mass ratios γ of layered bi-phasic granular matter mixtures and on the critical angle of its mono-disperse individual components. It also aims to investigate and explain regime transitions of granular matter flowing down a tilted rough inclined plane. Critical angles and flow regimes for a bi-phasic mixture of sago spheres and bi-phasic pepper mixture of fine powder and rough spheres were observed and measured using video analysis. The critical angles θc MD of mono-disperse granular matter and θc BP of biphasic granular matter mixtures were observed and compared. All types of flow regimes and a supramaximal critical angle of stability exist at mass ratio γ = 0.5 for all biphasic granular matter mixtures. The θc BP of sago spheres was higher than the θc MD of sago spheres. Moreover, the θc BP of the pepper mixture was in between the θc MD of fine pepper and θc MD of rough pepper spheres. Comparison of different granular material shows that θc MD is not simply a function of particle diameter but of particle roughness as well. Results point to a superposition mechanism of the critical angles of biphasic sphere mixtures.

  5. 40 CFR 721.5650 - Pentanediol light residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Pentanediol light residues. 721.5650... Substances § 721.5650 Pentanediol light residues. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as pentanediol light residues (PMN P-95-1750...

  6. 40 CFR 721.5650 - Pentanediol light residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Pentanediol light residues. 721.5650... Substances § 721.5650 Pentanediol light residues. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as pentanediol light residues (PMN P-95-1750...

  7. 40 CFR 721.5650 - Pentanediol light residues.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Pentanediol light residues. 721.5650... Substances § 721.5650 Pentanediol light residues. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as pentanediol light residues (PMN P-95-1750...

  8. 40 CFR 721.5650 - Pentanediol light residues.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Pentanediol light residues. 721.5650... Substances § 721.5650 Pentanediol light residues. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as pentanediol light residues (PMN P-95-1750...

  9. 40 CFR 721.5650 - Pentanediol light residues.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Pentanediol light residues. 721.5650... Substances § 721.5650 Pentanediol light residues. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as pentanediol light residues (PMN P-95-1750...

  10. Predicting logging residue volumes in the Pacific Northwest

    Treesearch

    Erik C. Berg; Todd A. Morgan; Eric A. Simmons; Stan Zarnoch; Micah G. Scudder

    2016-01-01

    Pacific Northwest forest managers seek estimates of post-timber-harvest woody residue volumes and biomass that can be related to readily available site- and tree-level attributes. To better predict residue production, researchers investigated variability in residue ratios, growing-stock residue volume per mill-delivered volume, across Idaho, Montana, Oregon, and...

  11. Managing logging residue under the timber sale contract.

    Treesearch

    Thomas C. Adams

    1980-01-01

    Management of logging residue is becoming an important part of timber sale planning. This involves controlling the amount of residue remaining on the ground and its distribution by diameter size class. Some residue is beneficial.An interdisciplinary team specified a desired residue level for one clearcutting unit of this trial. For comparison another cutting...

  12. Transcription factors for modification of lignin content in plants

    DOEpatents

    Wang, Huanzhong; Chen, Fang; Dixon, Richard A.

    2015-06-02

    The invention provides methods for modifying lignin, cellulose, xylan, and hemicellulose content in plants, and for achieving ectopic lignification and, for instance, secondary cell wall synthesis in pith cells, by altered regulation of a WRKY transcription factor. Nucleic acid constructs for altered WRKY-TF expression are described. Transgenic plants are provided that comprise modified pith cell walls, and lignin, cellulose, and hemicellulose content. Plants described herein may be used, for example, as improved biofuel feedstock and as highly digestible forage crops.

  13. 48 CFR 970.5001 - Residual powers.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Residual powers. 970.5001 Section 970.5001 Federal Acquisition Regulations System DEPARTMENT OF ENERGY AGENCY SUPPLEMENTARY....5001 Residual powers. ...

  14. 48 CFR 970.5001 - Residual powers.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 5 2011-10-01 2011-10-01 false Residual powers. 970.5001 Section 970.5001 Federal Acquisition Regulations System DEPARTMENT OF ENERGY AGENCY SUPPLEMENTARY....5001 Residual powers. ...

  15. Pesticide residues in birds and mammals

    USGS Publications Warehouse

    Stickel, L.F.; Edwards, C.A.

    1973-01-01

    SUMMARY: Residues of organochlorine pesticides and their breakdown products are present in the tissues of essentially all wild birds throughout the world. These chemicals accumulate in fat from a relatively small environmental exposure. DDE and dieldrin are most prevalent. Others, such as heptachlor epoxide, chlordane, endrin, and benzene hexachloride also occur, the quantities and kinds generally reflecting local or regional use. Accumulation may be sufficient to kill animals following applications for pest control. This has occurred in several large-scale programmes in the United States. Mortality has also resulted from unintentional leakage of chemical from commercial establishments. Residues may persist in the environment for many years, exposing successive generations of animals. In general, birds that eat other birds, or fish, have higher residues than those that eat seeds and vegetation. The kinetic processes of absorption, metabolism, storage, and output differ according to both kind of chemical and species of animal. When exposure is low and continuous, a balance between intake and excretion may be achieved. Residues reach a balance at an approximate animal body equilibrium or plateau; the storage is generally proportional to dose. Experiments with chickens show that dieldrin and heptachlor epoxide have the greatest propensity for storage, endrin next, then DDT, then lindane. The storage of DDT was complicated by its metabolism to DDE and DDD, but other studies show that DDE has a much greater propensity for storage than either DDD or DDT. Methoxychlor has little cumulative capacity in birds. Residues in eggs reflect and parallel those in the parent bird during accumulation, equilibrium, and decline when dosage is discontinued. Residues with the greatest propensity for storage are also lost most slowly. Rate of loss of residues can be modified by dietary components and is speeded by weight loss of the animal. Under sublethal conditions of continuous

  16. 40 CFR 180.496 - Thiazopyr; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.496 Thiazopyr; tolerances for residues. Tolerances are established for combined residues of the...

  17. 40 CFR 180.496 - Thiazopyr; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.496 Thiazopyr; tolerances for residues. Tolerances are established for combined residues of the...

  18. C-terminal amino acid residue loss for deprotonated peptide ions containing glutamic acid, aspartic acid, or serine residues at the C-terminus.

    PubMed

    Li, Zhong; Yalcin, Talat; Cassady, Carolyn J

    2006-07-01

    Deprotonated peptides containing C-terminal glutamic acid, aspartic acid, or serine residues were studied by sustained off-resonance irradiation collision-induced dissociation (SORI-CID) in a Fourier transform ion cyclotron resonance (FT-ICR) mass spectrometer with ion production by electrospray ionization (ESI). Additional studies were performed by post source decay (PSD) in a matrix-assisted laser desorption ionization/time-of-flight (MALDI/TOF) mass spectrometer. This work included both model peptides synthesized in our laboratory and bioactive peptides with more complex sequences. During SORI-CID and PSD, [M - H]- and [M - 2H]2- underwent an unusual cleavage corresponding to the elimination of the C-terminal residue. Two mechanisms are proposed to occur. They involve nucleophilic attack on the carbonyl carbon of the adjacent residue by either the carboxylate group of the C-terminus or the side chain carboxylate group of C-terminal glutamic acid and aspartic acid residues. To confirm the proposed mechanisms, AAAAAD was labelled by 18O specifically on the side chain of the aspartic acid residue. For peptides that contain multiple C-terminal glutamic acid residues, each of these residues can be sequentially eliminated from the deprotonated ions; a driving force may be the formation of a very stable pyroglutamatic acid neutral. For peptides with multiple aspartic acid residues at the C-terminus, aspartic acid residue loss is not sequential. For peptides with multiple serine residues at the C-terminus, C-terminal residue loss is sequential; however, abundant loss of other neutral molecules also occurs. In addition, the presence of basic residues (arginine or lysine) in the sequence has no effect on C-terminal residue elimination in the negative ion mode.

  19. Evaluation of heavy metals in hazardous automobile shredder residue thermal residue and immobilization with novel nano-size calcium dispersed reagent.

    PubMed

    Lee, Chi-Hyeon; Truc, Nguyen Thi Thanh; Lee, Byeong-Kyu; Mitoma, Yoshiharu; Mallampati, Srinivasa Reddy

    2015-10-15

    This study was conducted to synthesize and apply a nano-size calcium dispersed reagent as an immobilization material for heavy metal-contaminated automobile shredder residues (ASR) dust/thermal residues in dry condition. Simple mixing with a nanometallic Ca/CaO/PO4 dispersion mixture immobilized 95-100% of heavy metals in ASR dust/thermal residues (including bottom ash, cavity ash, boiler and bag filter ash). The quantity of heavy metals leached from thermal residues after treatment by nanometallic Ca/CaO/PO4 was lower than the Korean standard regulatory limit for hazardous waste landfills. The morphology and elemental composition of the nanometallic Ca/CaO-treated ASR residue were characterized by field emission scanning election microscopy combined with electron dispersive spectroscopy (FE-SEM/EDS). The results indicated that the amounts of heavy metals detectable on the ASR thermal residue surface decreased and the Ca/PO4 mass percent increased. X-ray diffraction (XRD) pattern analysis indicated that the main fraction of enclosed/bound materials on ASR residue included Ca/PO4- associated crystalline complexes, and that immobile Ca/PO4 salts remarkably inhibited the desorption of heavy metals from ASR residues. These results support the potential use of nanometallic Ca/CaO/PO4 as a simple, suitable and highly efficient material for the gentle immobilization of heavy metals in hazardous ASR thermal residue in dry condition. Copyright © 2015 Elsevier B.V. All rights reserved.

  20. 40 CFR 180.274 - Propanil; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.274 Propanil; tolerances for residues. (a) General. Tolerances are established for the combined residues of the...

  1. Variability in pesticides residues--the US experience.

    PubMed

    Suhre, F B

    2000-07-01

    The evolution of US Environmental Protection Agency's (EPA) process for estimating potential health risks from pesticide residues in or on food is examined in light of changes in US Legislation and the variability of residue data and assumptions used to estimate dietary exposure. In the 86 years since enactment of the Insecticide Act, pesticide laws have become progressively more health-based. Passage of the 1996 Food Quality Protection Act (FQPA) requires EPA to place particular emphasis on assessing potential risk from pesticides to infants and children. Primary factors affecting the actual pesticide residues in food include frequency of application, percentage of crop treated, and the interval from treatment to harvest. Primary factors affecting the estimated pesticide residues in food include the source of the residue data, calculation techniques for non-detected residues, and the availability of data reflecting post-harvest treatments. Risk assessors must thoroughly consider these factors when assessing dietary risk to pesticides. Risk managers will need to consider these factors as a means of mitigating dietary risk from pesticides.

  2. 48 CFR 250.104 - Residual powers.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Residual powers. 250.104 Section 250.104 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT... Contractual Actions 250.104 Residual powers. ...

  3. 48 CFR 250.104 - Residual powers.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 3 2011-10-01 2011-10-01 false Residual powers. 250.104 Section 250.104 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT... Contractual Actions 250.104 Residual powers. ...

  4. 40 CFR 180.432 - Lactofen; tolerances for residues.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Lactofen; tolerances for residues. (a) General. Tolerances are established for residues of the herbicide... defined in § 180.1(l), are established for residues of the herbicide lactofen, including its metabolites...

  5. 40 CFR 180.432 - Lactofen; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Lactofen; tolerances for residues. (a) General. Tolerances are established for residues of the herbicide... defined in § 180.1(l), are established for residues of the herbicide lactofen, including its metabolites...

  6. 40 CFR 180.432 - Lactofen; tolerances for residues.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Lactofen; tolerances for residues. (a) General. Tolerances are established for residues of the herbicide... defined in § 180.1(l), are established for residues of the herbicide lactofen, including its metabolites...

  7. 40 CFR 180.432 - Lactofen; tolerances for residues.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Lactofen; tolerances for residues. (a) General. Tolerances are established for residues of the herbicide... defined in § 180.1(l), are established for residues of the herbicide lactofen, including its metabolites...

  8. Influence of organic waste and residue mud additions on chemical, physical and microbial properties of bauxite residue sand.

    PubMed

    Jones, Benjamin E H; Haynes, Richard J; Phillips, Ian R

    2011-02-01

    In an alumina refinery, bauxite ore is treated with sodium hydroxide at high temperatures and pressures and for every tone of alumina produced, about 2 tones of alkaline, saline bauxite processing waste is also produced. At Alcoa, a dry stacking system of disposal is used, and it is the sand fraction of the processing waste that is rehabilitated. There is little information available regarding the most appropriate amendments to add to the processing sand to aid in revegetation. The purpose of this study was to investigate how the addition of organic wastes (biosolids and poultry manure), in the presence or absence of added residue mud, would affect the properties of the residue sand and its suitability for revegetation. Samples of freshly deposited residue sand were collected from Alcoa's Kwinana refinery. Samples were treated with phosphogypsum (2% v/v), incubated, and leached. A laboratory experiment was then set up in which the two organic wastes were applied at 0 or the equivalent to 60 tones ha(-1) in combination with residue mud added at rates of 0%, 10% and 20% v/v. Samples were incubated for 8 weeks, after which, key chemical, physical and microbial properties of the residue sand were measured along with seed germination. Additions of residue mud increased exchangeable Na(+), ESP and the pH, and HCO (3) (-) and Na(+) concentrations in saturation paste extracts. Additions of biosolids and poultry manure increased concentrations of extractable P, NH (4) (+) , K, Mg, Cu, Zn, Mn and Fe. Addition of residue mud, in combination with organic wastes, caused a marked decrease in macroporosity and a concomitant increase in mesoporosity, available water holding capacity and the quantity of water held at field capacity. With increasing residue mud additions, the percentage of sample present as sand particles (<1 mm diameter) decreased, and the percentage present in aggregated form (>2 mm diameter) increased; greatest aggregation occurred where a combination of residue

  9. 12 CFR 23.21 - Estimated residual value.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 12 Banks and Banking 1 2010-01-01 2010-01-01 false Estimated residual value. 23.21 Section 23.21...) Leases § 23.21 Estimated residual value. (a) Recovery of investment and costs. A national bank's estimate of the residual value of the property that the bank relies upon to satisfy the requirements of a full...

  10. 40 CFR 180.339 - MCPA; tolerances for residues.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ...; tolerances for residues. (a) General. (1) Tolerances are established for residues of the herbicide MCPA ((4... for residues of the herbicide MCPA ((4-chloro-2-methylphenoxy)acetic acid) resulting from the direct...

  11. 40 CFR 180.339 - MCPA; tolerances for residues.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ...; tolerances for residues. (a) General. (1) Tolerances are established for residues of the herbicide MCPA ((4... for residues of the herbicide MCPA ((4-chloro-2-methylphenoxy)acetic acid) resulting from the direct...

  12. 40 CFR 180.339 - MCPA; tolerances for residues.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ...; tolerances for residues. (a) General. (1) Tolerances are established for residues of the herbicide MCPA ((4... for residues of the herbicide MCPA ((4-chloro-2-methylphenoxy)acetic acid) resulting from the direct...

  13. 40 CFR 180.417 - Triclopyr; tolerances for residues.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... § 180.417 Triclopyr; tolerances for residues. (a) General. (1) Tolerances for residues of the herbicide...) Tolerances for the combined residues of the herbicide triclopyr ((3,5,6-trichloro-2-pyridinyl)oxy) acetic...

  14. 40 CFR 180.417 - Triclopyr; tolerances for residues.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... § 180.417 Triclopyr; tolerances for residues. (a) General. (1) Tolerances for residues of the herbicide...) Tolerances for the combined residues of the herbicide triclopyr ((3,5,6-trichloro-2-pyridinyl)oxy) acetic...

  15. 40 CFR 180.417 - Triclopyr; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... § 180.417 Triclopyr; tolerances for residues. (a) General. (1) Tolerances for residues of the herbicide...) Tolerances for the combined residues of the herbicide triclopyr ((3,5,6-trichloro-2-pyridinyl)oxy) acetic...

  16. 40 CFR 180.417 - Triclopyr; tolerances for residues.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... § 180.417 Triclopyr; tolerances for residues. (a) General. (1) Tolerances for residues of the herbicide...) Tolerances for the combined residues of the herbicide triclopyr ((3,5,6-trichloro-2-pyridinyl)oxy) acetic...

  17. 40 CFR 180.432 - Lactofen; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Lactofen; tolerances for residues. (a) Tolerances are established for residues of the herbicide lactofen, 1... defined in 180.1(n) are established for residues of the herbicide, lactofen, 1-(carboethoxy)ethyl 5-[2...

  18. 40 CFR 180.417 - Triclopyr; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... § 180.417 Triclopyr; tolerances for residues. (a) General. (1) Tolerances for residues of the herbicide...) Tolerances for the combined residues of the herbicide triclopyr ((3,5,6-trichloro-2-pyridinyl)oxy) acetic...

  19. PESTICIDE RESIDUE RECOVERIES FROM SURFACE WIPES

    EPA Science Inventory

    Human exposure is a consequence of pesticide use indoors with a primary source resulting from residue deposition on household surfaces. Accurate measurements of surface residues is essential for estimating exposure from different routes. Various procedures have been developed ...

  20. Logging residue in southeast Alaska.

    Treesearch

    James O. Howard; Theodore S. Setzer

    1989-01-01

    Detailed information on logging residues in southeast Alaska is provided as input to economic and technical assessments of its use for products or site amenities. Two types of information are presented. Ratios are presented that can be used to generate an estimate, based on volume or acres harvested, of the cubic-foot volume of residue for any particular area of...

  1. Taking inventory of woody residuals

    Treesearch

    David McKeever

    2003-01-01

    USDA Forest Service analysis finds 104 million tons of woody residuals available for recovery in the U.S., with wood in MSW and C&D debris streams comprising 28 million tons. The U.S. Department of Agriculture Forest Service conducts a variety of analyses to estimate the quantity of woody residuals in the United States. Its Forest Products Laboratory in Madison,...

  2. 40 CFR 180.123 - Inorganic bromide residues resulting from fumigation with methyl bromide; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... from fumigation with methyl bromide; tolerances for residues. 180.123 Section 180.123 Protection of... fumigation with methyl bromide; tolerances for residues. (a) General. (1) Tolerances are established for... result of fumigation of the processed food with methyl bromide or from such fumigation in addition to the...

  3. CO2CRC's Otway Residual Saturation and Dissolution Test: Using Reactive Ester Tracers to Determine Residual CO2 Saturation

    NASA Astrophysics Data System (ADS)

    Myers, M.; Stalker, L.; LaForce, T.; Pejcic, B.; Dyt, C.; Ho, K.; Ennis-King, J.

    2013-12-01

    Residual trapping, that is CO2 held in the rock pore space due to capillarity, is an important storage mechanism in geo-sequestration of over the short to medium term (up to 1000 years). As such residual CO2 saturation is a critical reservoir parameter for assessing the storage capacity and security of carbon capture and storage (CCS). As a component of the CO2CRC's Residual Gas Saturation and Dissolution Test at the CO2CRC Otway Project site in Victoria (Australia), we have recently tested a suite of reactive esters (triacetin, tripropionin and propylene glycol diacetate) in a single well chemical tracer test to determine residual CO2 saturation. The goal of this project was to assess and validate a suite of possible tests that could be implemented to determine residual CO2 saturation. For this test, the chemical tracers were injected with a saturated CO2/water mixture into the formation (that is already at residual CO2 saturation) where they were allowed to 'soak' for approximately 10 days allowing for the partial hydrolysis of the esters to their corresponding carboxylic acids and alcohols. Water containing the tracers was then produced from the well resulting in over 600 tracer samples over a period of 12 hours. A selection of these samples were analysed for tracer content and to establish tracer breakthrough curves. To understand the behaviour of these chemical tracers in the downhole environment containing residually trapped supercritical CO2 and formation water, it is necessary to determine the supercritical CO2/water partition coefficients. We have previously determined these in the laboratory (Myers et al., 2012) and they are used here to model the tracer behaviour and provide an estimate of the residual CO2 saturation. Two different computational simulators were used to analyse the tracer breakthrough profiles. The first is based on simple chromatographic retardation and has been used extensively in single well chemical tracer tests to determine residual

  4. Comparing corn types for differences in cell wall characteristics and p-coumaroylation of lignin.

    PubMed

    Hatfield, Ronald D; Chaptman, Ann K

    2009-05-27

    This study was undertaken to compare cell wall characteristics including levels of p-coumarate (pCA) and lignin in corn (Zea mays L.) types. Five different types of corn, four commercial and Teosinte, were grown in the greenhouse in individual pots. For each corn type replicate stems were harvested at tassel emergence. Tissues for cell wall analysis were harvested from stems (separated into rind and pith tissues) and roots. Stem cell wall characteristics across the different corn types were similar for total neutral sugars, total uronosyls, lignin, and phenolic acids. However, the neutral sugar composition of root cell walls was markedly different, with high levels of galactose and arabinose. Levels of pCA in the different tissues ranged from 13.8 to 33.1 mg g(-1) of CW depending upon the type of tissue. There was no evidence that pCA was incorporated into cell walls attached to arabinoxylans. Lignin levels were similar within a given tissue, with pith ranging from 86.1 to 132.0 mg g(-1) of CW, rind from 178.4 to 236.6 mg g(-1) of CW, and roots from 216.5 to 242.6 mg g(-1) of CW. The higher values for lignins in root tissue may be due to suberin remaining in the acid-insoluble residue, forming Klason lignins. With the exception of root tissues, higher pCA levels accompanied higher lignin levels. This may indicate a potential role of pCA aiding lignin formation in corn cell walls during the lignification process.

  5. Residual stresses of thin, short rectangular plates

    NASA Technical Reports Server (NTRS)

    Andonian, A. T.; Danyluk, S.

    1985-01-01

    The analysis of the residual stresses in thin, short rectangular plates is presented. The analysis is used in conjunction with a shadow moire interferometry technique by which residual stresses are obtained over a large spatial area from a strain measurement. The technique and analysis are applied to a residual stress measurement of polycrystalline silicon sheet grown by the edge-defined film growth technique.

  6. Logging Residue Available for Mine-Timber Production

    Treesearch

    Floyd G. Timson

    1978-01-01

    Hardwood logging residue was examined as a source of raw material in the manufacture of sawn, split, and round timbers for use in underground coal mines. Forty-four percent of the total logging residue (residue !U 4 inches in diameter outside bark (dob), small end, and 4 feet long) from sawlog-only harvests was suitable for mine-timber production. Only 26 percent of...

  7. BOOSTER CHLORINATION FOR MANAGING DISINFECTANT RESIDUALS

    EPA Science Inventory

    Booster chlorination is an approach to residual maintenance in which chlorine is applied at strategic locations within the distribution system. Situations in which booster chlorination may be most effective for maintaining a residual are explained informally in the context of a ...

  8. Residual Energy Spectrum of Solar Wind Turbulence

    NASA Astrophysics Data System (ADS)

    Chen, C. H. K.; Bale, S. D.; Salem, C. S.; Maruca, B. A.

    2013-06-01

    It has long been known that the energy in velocity and magnetic field fluctuations in the solar wind is not in equipartition. In this paper, we present an analysis of 5 yr of Wind data at 1 AU to investigate the reason for this. The residual energy (difference between energy in velocity and magnetic field fluctuations) was calculated using both the standard magnetohydrodynamic (MHD) normalization for the magnetic field and a kinetic version, which includes temperature anisotropies and drifts between particle species. It was found that with the kinetic normalization, the fluctuations are closer to equipartition, with a mean normalized residual energy of σr = -0.19 and mean Alfvén ratio of r A = 0.71. The spectrum of residual energy, in the kinetic normalization, was found to be steeper than both the velocity and magnetic field spectra, consistent with some recent MHD turbulence predictions and numerical simulations, having a spectral index close to -1.9. The local properties of residual energy and cross helicity were also investigated, showing that globally balanced intervals with small residual energy contain local patches of larger imbalance and larger residual energy at all scales, as expected for nonlinear turbulent interactions.

  9. Computational prediction of protein hot spot residues.

    PubMed

    Morrow, John Kenneth; Zhang, Shuxing

    2012-01-01

    Most biological processes involve multiple proteins interacting with each other. It has been recently discovered that certain residues in these protein-protein interactions, which are called hot spots, contribute more significantly to binding affinity than others. Hot spot residues have unique and diverse energetic properties that make them challenging yet important targets in the modulation of protein-protein complexes. Design of therapeutic agents that interact with hot spot residues has proven to be a valid methodology in disrupting unwanted protein-protein interactions. Using biological methods to determine which residues are hot spots can be costly and time consuming. Recent advances in computational approaches to predict hot spots have incorporated a myriad of features, and have shown increasing predictive successes. Here we review the state of knowledge around protein-protein interactions, hot spots, and give an overview of multiple in silico prediction techniques of hot spot residues.

  10. Americium recovery from reduction residues

    DOEpatents

    Conner, W.V.; Proctor, S.G.

    1973-12-25

    A process for separation and recovery of americium values from container or bomb'' reduction residues comprising dissolving the residues in a suitable acid, adjusting the hydrogen ion concentration to a desired level by adding a base, precipitating the americium as americium oxalate by adding oxalic acid, digesting the solution, separating the precipitate, and thereafter calcining the americium oxalate precipitate to form americium oxide. (Official Gazette)

  11. 40 CFR 158.1410 - Residue chemistry data requirements table.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Residue chemistry data requirements...) PESTICIDE PROGRAMS DATA REQUIREMENTS FOR PESTICIDES Residue Chemistry § 158.1410 Residue chemistry data... the residue chemistry data requirements for a particular pesticide product. Notes that apply to an...

  12. 40 CFR 158.1410 - Residue chemistry data requirements table.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 25 2012-07-01 2012-07-01 false Residue chemistry data requirements...) PESTICIDE PROGRAMS DATA REQUIREMENTS FOR PESTICIDES Residue Chemistry § 158.1410 Residue chemistry data... the residue chemistry data requirements for a particular pesticide product. Notes that apply to an...

  13. 40 CFR 158.1410 - Residue chemistry data requirements table.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 25 2013-07-01 2013-07-01 false Residue chemistry data requirements...) PESTICIDE PROGRAMS DATA REQUIREMENTS FOR PESTICIDES Residue Chemistry § 158.1410 Residue chemistry data... the residue chemistry data requirements for a particular pesticide product. Notes that apply to an...

  14. 40 CFR 158.1410 - Residue chemistry data requirements table.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 24 2011-07-01 2011-07-01 false Residue chemistry data requirements...) PESTICIDE PROGRAMS DATA REQUIREMENTS FOR PESTICIDES Residue Chemistry § 158.1410 Residue chemistry data... the residue chemistry data requirements for a particular pesticide product. Notes that apply to an...

  15. 40 CFR 158.1410 - Residue chemistry data requirements table.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 24 2014-07-01 2014-07-01 false Residue chemistry data requirements...) PESTICIDE PROGRAMS DATA REQUIREMENTS FOR PESTICIDES Residue Chemistry § 158.1410 Residue chemistry data... the residue chemistry data requirements for a particular pesticide product. Notes that apply to an...

  16. Residues of lambda-cyhalothrin in tea.

    PubMed

    Seenivasan, Subbiah; Muraleedharan, Narayanan Nair

    2009-02-01

    Field experiments were conducted at two places in Tamil Nadu (India) during dry season of 2006 to determine the residues of lambda-cyhalothrin in fresh green tea leaves and black tea. Residues were quantified at different harvest intervals of '0' (3h), 1st, 3rd, 5th, 7th, 10th and 14th day after insecticide application. Persistence, dissipation pattern, half-life value and safe harvest interval of the insecticide in tea were calculated. Residues of lambda-cyhalothrin dissipated exponentially after application at both the locations and reached below the European Union maximum residue limit (MRL) of 1mg/kg on the 5th day. Lambda-cyhalothrin showed that like other insecticides it followed the first order dissipation kinetics. Half-life values varied from 2.8 to 3.5 days for lambda-cyhalothrin and a safety harvest interval of 5 days is suggested for tea at the recommended dosage.

  17. RESIDUAL RISK ASSESSMENTS - RESIDUAL RISK ...

    EPA Pesticide Factsheets

    This source category previously subjected to a technology-based standard will be examined to determine if health or ecological risks are significant enough to warrant further regulation for Coke Ovens. These assesments utilize existing models and data bases to examine the multi-media and multi-pollutant impacts of air toxics emissions on human health and the environment. Details on the assessment process and methodologies can be found in EPA's Residual Risk Report to Congress issued in March of 1999 (see web site). To assess the health risks imposed by air toxics emissions from Coke Ovens to determine if control technology standards previously established are adequately protecting public health.

  18. Genomic Prediction Accounting for Residual Heteroskedasticity.

    PubMed

    Ou, Zhining; Tempelman, Robert J; Steibel, Juan P; Ernst, Catherine W; Bates, Ronald O; Bello, Nora M

    2015-11-12

    Whole-genome prediction (WGP) models that use single-nucleotide polymorphism marker information to predict genetic merit of animals and plants typically assume homogeneous residual variance. However, variability is often heterogeneous across agricultural production systems and may subsequently bias WGP-based inferences. This study extends classical WGP models based on normality, heavy-tailed specifications and variable selection to explicitly account for environmentally-driven residual heteroskedasticity under a hierarchical Bayesian mixed-models framework. WGP models assuming homogeneous or heterogeneous residual variances were fitted to training data generated under simulation scenarios reflecting a gradient of increasing heteroskedasticity. Model fit was based on pseudo-Bayes factors and also on prediction accuracy of genomic breeding values computed on a validation data subset one generation removed from the simulated training dataset. Homogeneous vs. heterogeneous residual variance WGP models were also fitted to two quantitative traits, namely 45-min postmortem carcass temperature and loin muscle pH, recorded in a swine resource population dataset prescreened for high and mild residual heteroskedasticity, respectively. Fit of competing WGP models was compared using pseudo-Bayes factors. Predictive ability, defined as the correlation between predicted and observed phenotypes in validation sets of a five-fold cross-validation was also computed. Heteroskedastic error WGP models showed improved model fit and enhanced prediction accuracy compared to homoskedastic error WGP models although the magnitude of the improvement was small (less than two percentage points net gain in prediction accuracy). Nevertheless, accounting for residual heteroskedasticity did improve accuracy of selection, especially on individuals of extreme genetic merit. Copyright © 2016 Ou et al.

  19. Genomic Prediction Accounting for Residual Heteroskedasticity

    PubMed Central

    Ou, Zhining; Tempelman, Robert J.; Steibel, Juan P.; Ernst, Catherine W.; Bates, Ronald O.; Bello, Nora M.

    2015-01-01

    Whole-genome prediction (WGP) models that use single-nucleotide polymorphism marker information to predict genetic merit of animals and plants typically assume homogeneous residual variance. However, variability is often heterogeneous across agricultural production systems and may subsequently bias WGP-based inferences. This study extends classical WGP models based on normality, heavy-tailed specifications and variable selection to explicitly account for environmentally-driven residual heteroskedasticity under a hierarchical Bayesian mixed-models framework. WGP models assuming homogeneous or heterogeneous residual variances were fitted to training data generated under simulation scenarios reflecting a gradient of increasing heteroskedasticity. Model fit was based on pseudo-Bayes factors and also on prediction accuracy of genomic breeding values computed on a validation data subset one generation removed from the simulated training dataset. Homogeneous vs. heterogeneous residual variance WGP models were also fitted to two quantitative traits, namely 45-min postmortem carcass temperature and loin muscle pH, recorded in a swine resource population dataset prescreened for high and mild residual heteroskedasticity, respectively. Fit of competing WGP models was compared using pseudo-Bayes factors. Predictive ability, defined as the correlation between predicted and observed phenotypes in validation sets of a five-fold cross-validation was also computed. Heteroskedastic error WGP models showed improved model fit and enhanced prediction accuracy compared to homoskedastic error WGP models although the magnitude of the improvement was small (less than two percentage points net gain in prediction accuracy). Nevertheless, accounting for residual heteroskedasticity did improve accuracy of selection, especially on individuals of extreme genetic merit. PMID:26564950

  20. Imaging residue transfer into egg yolks.

    PubMed

    Donoghue, D J; Myers, K

    2000-12-01

    Prediction models for residue transfer into eggs are being developed. Recent results indicate that the developing egg yolk serves as an important storage depot for chemical residues. The current study was conducted to visualize incorporation and potential compartmentalization of drug residues in developing egg yolks. To this end, the drug magnevist was injected into hens to evaluate drug transfer into either early- or late-developing yolks. High-resolution magnetic resonance images (MRI) of drug residues in eggs were acquired using a 1.5 T Siemens Magnetom clinical scanner. A 10-cm circular surface coil was used for receiving the magnetic resonance signal. The eggs were positioned inside the coil cavity for an improved signal to noise ratio (SNR). Gradient-echo images were used to locate the centers of the eggs and to prescribe the position of the high-resolution image slab. The images were recorded using an inversion time (T1) weighted magnetization-prepared, rapid acquisition, gradient-recalled-echo (MPRAGE) pulse sequence. The sequence parameters used were as follows: repetition time (TR) equals 12 ms, echo time (TE) equals 5 ms, field of view (FOV) equals 200, TI = 10 ms, 1.25-mm slice thickness, and a matrix of 200 x 256. Following dosing, images of drug residues in eggs indicate that drugs can be incorporated and compartmentalized into ring structures within individual developing egg yolks. These results have significant human food safety implications because even after only a single dose, sequestered drug residues may be stored and later released to contaminate eggs for days to weeks after dosing.

  1. 40 CFR 180.245 - Streptomycin; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Streptomycin; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.245 Streptomycin; tolerances for residues. (a) General. (1) Tolerances are established for...

  2. 40 CFR 180.245 - Streptomycin; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 24 2011-07-01 2011-07-01 false Streptomycin; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.245 Streptomycin; tolerances for residues. (a) General. (1) Tolerances are established for...

  3. Residue decomposition of submodel of WEPS

    USDA-ARS?s Scientific Manuscript database

    The Residue Decomposition submodel of the Wind Erosion Prediction System (WEPS) simulates the decrease in crop residue biomass due to microbial activity. The decomposition process is modeled as a first-order reaction with temperature and moisture as driving variables. Decomposition is a function of ...

  4. 48 CFR 1450.104 - Residual powers.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Residual powers. 1450.104 Section 1450.104 Federal Acquisition Regulations System DEPARTMENT OF THE INTERIOR CONTRACT MANAGEMENT EXTRAORDINARY CONTRACTUAL ACTIONS AND THE SAFETY ACT Extraordinary Contractual Actions 1450.104 Residual powers. ...

  5. 48 CFR 1450.104 - Residual powers.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 5 2011-10-01 2011-10-01 false Residual powers. 1450.104 Section 1450.104 Federal Acquisition Regulations System DEPARTMENT OF THE INTERIOR CONTRACT MANAGEMENT EXTRAORDINARY CONTRACTUAL ACTIONS AND THE SAFETY ACT Extraordinary Contractual Actions 1450.104 Residual powers. ...

  6. [Migrants from disposable gloves and residual acrylonitrile].

    PubMed

    Wakui, C; Kawamura, Y; Maitani, T

    2001-10-01

    Disposable gloves made from polyvinyl chloride with and without di(2-ethylhexyl) phthalate (PVC-DEHP, PVC-NP), polyethylene (PE), natural rubber (NR) and nitrile-butadiene rubber (NBR) were investigated with respect to evaporation residue, migrated metals, migrants and residual acrylonitrile. The evaporation residue found in n-heptane was 870-1,300 ppm from PVC-DEHP and PVC-NP, which was due to the plasticizers. Most of the PE gloves had low evaporation residue levels and migrants, except for the glove designated as antibacterial, which released copper and zinc into 4% acetic acid. For the NR and NBR gloves, the evaporation residue found in 4% acetic acid was 29-180 ppm. They also released over 10 ppm of calcium and 6 ppm of zinc into 4% acetic acid, and 1.68-8.37 ppm of zinc di-ethyldithiocarbamate and zinc di-n-butyldithiocarbamate used as vulcanization accelerators into n-heptane. The acrylonitrile content was 0.40-0.94 ppm in NBR gloves.

  7. Protein structure based prediction of catalytic residues.

    PubMed

    Fajardo, J Eduardo; Fiser, Andras

    2013-02-22

    Worldwide structural genomics projects continue to release new protein structures at an unprecedented pace, so far nearly 6000, but only about 60% of these proteins have any sort of functional annotation. We explored a range of features that can be used for the prediction of functional residues given a known three-dimensional structure. These features include various centrality measures of nodes in graphs of interacting residues: closeness, betweenness and page-rank centrality. We also analyzed the distance of functional amino acids to the general center of mass (GCM) of the structure, relative solvent accessibility (RSA), and the use of relative entropy as a measure of sequence conservation. From the selected features, neural networks were trained to identify catalytic residues. We found that using distance to the GCM together with amino acid type provide a good discriminant function, when combined independently with sequence conservation. Using an independent test set of 29 annotated protein structures, the method returned 411 of the initial 9262 residues as the most likely to be involved in function. The output 411 residues contain 70 of the annotated 111 catalytic residues. This represents an approximately 14-fold enrichment of catalytic residues on the entire input set (corresponding to a sensitivity of 63% and a precision of 17%), a performance competitive with that of other state-of-the-art methods. We found that several of the graph based measures utilize the same underlying feature of protein structures, which can be simply and more effectively captured with the distance to GCM definition. This also has the added the advantage of simplicity and easy implementation. Meanwhile sequence conservation remains by far the most influential feature in identifying functional residues. We also found that due the rapid changes in size and composition of sequence databases, conservation calculations must be recalibrated for specific reference databases.

  8. Protein structure based prediction of catalytic residues

    PubMed Central

    2013-01-01

    Background Worldwide structural genomics projects continue to release new protein structures at an unprecedented pace, so far nearly 6000, but only about 60% of these proteins have any sort of functional annotation. Results We explored a range of features that can be used for the prediction of functional residues given a known three-dimensional structure. These features include various centrality measures of nodes in graphs of interacting residues: closeness, betweenness and page-rank centrality. We also analyzed the distance of functional amino acids to the general center of mass (GCM) of the structure, relative solvent accessibility (RSA), and the use of relative entropy as a measure of sequence conservation. From the selected features, neural networks were trained to identify catalytic residues. We found that using distance to the GCM together with amino acid type provide a good discriminant function, when combined independently with sequence conservation. Using an independent test set of 29 annotated protein structures, the method returned 411 of the initial 9262 residues as the most likely to be involved in function. The output 411 residues contain 70 of the annotated 111 catalytic residues. This represents an approximately 14-fold enrichment of catalytic residues on the entire input set (corresponding to a sensitivity of 63% and a precision of 17%), a performance competitive with that of other state-of-the-art methods. Conclusions We found that several of the graph based measures utilize the same underlying feature of protein structures, which can be simply and more effectively captured with the distance to GCM definition. This also has the added the advantage of simplicity and easy implementation. Meanwhile sequence conservation remains by far the most influential feature in identifying functional residues. We also found that due the rapid changes in size and composition of sequence databases, conservation calculations must be recalibrated for specific

  9. Residue frequencies and pairing preferences at protein-protein interfaces.

    PubMed

    Glaser, F; Steinberg, D M; Vakser, I A; Ben-Tal, N

    2001-05-01

    We used a nonredundant set of 621 protein-protein interfaces of known high-resolution structure to derive residue composition and residue-residue contact preferences. The residue composition at the interfaces, in entire proteins and in whole genomes correlates well, indicating the statistical strength of the data set. Differences between amino acid distributions were observed for interfaces with buried surface area of less than 1,000 A(2) versus interfaces with area of more than 5,000 A(2). Hydrophobic residues were abundant in large interfaces while polar residues were more abundant in small interfaces. The largest residue-residue preferences at the interface were recorded for interactions between pairs of large hydrophobic residues, such as Trp and Leu, and the smallest preferences for pairs of small residues, such as Gly and Ala. On average, contacts between pairs of hydrophobic and polar residues were unfavorable, and the charged residues tended to pair subject to charge complementarity, in agreement with previous reports. A bootstrap procedure, lacking from previous studies, was used for error estimation. It showed that the statistical errors in the set of pairing preferences are generally small; the average standard error is approximately 0.2, i.e., about 8% of the average value of the pairwise index (2.9). However, for a few pairs (e.g., Ser-Ser and Glu-Asp) the standard error is larger in magnitude than the pairing index, which makes it impossible to tell whether contact formation is favorable or unfavorable. The results are interpreted using physicochemical factors and their implications for the energetics of complex formation and for protein docking are discussed. Proteins 2001;43:89-102. Copyright 2001 Wiley-Liss, Inc.

  10. CAB-Align: A Flexible Protein Structure Alignment Method Based on the Residue-Residue Contact Area.

    PubMed

    Terashi, Genki; Takeda-Shitaka, Mayuko

    2015-01-01

    Proteins are flexible, and this flexibility has an essential functional role. Flexibility can be observed in loop regions, rearrangements between secondary structure elements, and conformational changes between entire domains. However, most protein structure alignment methods treat protein structures as rigid bodies. Thus, these methods fail to identify the equivalences of residue pairs in regions with flexibility. In this study, we considered that the evolutionary relationship between proteins corresponds directly to the residue-residue physical contacts rather than the three-dimensional (3D) coordinates of proteins. Thus, we developed a new protein structure alignment method, contact area-based alignment (CAB-align), which uses the residue-residue contact area to identify regions of similarity. The main purpose of CAB-align is to identify homologous relationships at the residue level between related protein structures. The CAB-align procedure comprises two main steps: First, a rigid-body alignment method based on local and global 3D structure superposition is employed to generate a sufficient number of initial alignments. Then, iterative dynamic programming is executed to find the optimal alignment. We evaluated the performance and advantages of CAB-align based on four main points: (1) agreement with the gold standard alignment, (2) alignment quality based on an evolutionary relationship without 3D coordinate superposition, (3) consistency of the multiple alignments, and (4) classification agreement with the gold standard classification. Comparisons of CAB-align with other state-of-the-art protein structure alignment methods (TM-align, FATCAT, and DaliLite) using our benchmark dataset showed that CAB-align performed robustly in obtaining high-quality alignments and generating consistent multiple alignments with high coverage and accuracy rates, and it performed extremely well when discriminating between homologous and nonhomologous pairs of proteins in both

  11. 40 CFR 180.659 - Pyroxasulfone; tolerances for residues.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... residues of the herbicide pyroxasulfone, including its metabolites and degradates, in or on the commodities... Wheat, grain 0.03 (2) Tolerances are established for residues of the herbicide pyroxasulfone, including..., straw 0.60 (3) Tolerances are established for residues of the herbicide pyroxasulfone, including its...

  12. 40 CFR 180.184 - Linuron; tolerances for residues.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Linuron; tolerances for residues. (a) General. Tolerances are established for residues of the herbicide.... Time-limited tolerances are established for residues of the herbicide linuron [3-(3,4-dichlorophenyl)-1... herbicide linuron (3-(3,4-dichlorophenyl)-1-methoxy-1-methylurea), including its metabolites and degradates...

  13. 40 CFR 180.507 - Azoxystrobin; tolerances for residues.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 25 2012-07-01 2012-07-01 false Azoxystrobin; tolerances for residues... § 180.507 Azoxystrobin; tolerances for residues. (a) General. (1) Tolerances are established for residues of the fungicide, azoxystrobin, including its metabolites and degradates, in or on the commodities...

  14. Optical computation using residue arithmetic.

    PubMed

    Huang, A; Tsunoda, Y; Goodman, J W; Ishihara, S

    1979-01-15

    Using residue arithmetic it is possible to perform additions, subtractions, multiplications, and polynomial evaluation without the necessity for carry operations. Calculations can, therefore, be performed in a fully parallel manner. Several different optical methods for performing residue arithmetic operations are described. A possible combination of such methods to form a matrix vector multiplier is considered. The potential advantages of optics in performing these kinds of operations are discussed.

  15. Processing hardwood bark residues by screening

    Treesearch

    David M. Emanuel

    1978-01-01

    Most of the hardwood bark residues removed by floating-cutterhead or rosserhead debarkers can be processed into acceptable bark products by screening alone. And by prescreening bark residues, operators of bark processing plants can use smaller hammermills than otherwise are required, thus lowering investment and energy costs.

  16. Lamination residual stresses in fiber composites

    NASA Technical Reports Server (NTRS)

    Daniel, I. M.; Liber, T.

    1975-01-01

    An experimental investigation was conducted to determine the magnitude of lamination residual stresses in angle-ply composites and to evaluate their effects on composite structural integrity. The materials investigated were boron/epoxy, boron/polyimide, graphite/low modulus epoxy, graphite/high modulus epoxy, graphite/polyimide and s-glass/epoxy. These materials were fully characterized. Static properties of laminates were also determined. Experimental techniques using embedded strain gages were developed and used to measure residual strains during curing. The extent of relaxation of lamination residual stresses was investigated. It was concluded that the degree of such relaxation is low. The behavior of angle-ply laminates subjected to thermal cycling, tensile load cycling, and combined thermal cycling with tensile load was investigated. In most cases these cycling programs did not have any measurable influence on residual strength and stiffness of the laminates. In the tensile load cycling tests, the graphite/polyimide shows the highest endurance with 10 million cycle runouts at loads up to 90 percent of the static strength.

  17. [Development of residual voltage testing equipment].

    PubMed

    Zeng, Xiaohui; Wu, Mingjun; Cao, Li; He, Jinyi; Deng, Zhensheng

    2014-07-01

    For the existing measurement methods of residual voltage which can't turn the power off at peak voltage exactly and simultaneously display waveforms, a new residual voltage detection method is put forward in this paper. First, the zero point of the power supply is detected with zero cross detection circuit and is inputted to a single-chip microcomputer in the form of pulse signal. Secend, when the zero point delays to the peak voltage, the single-chip microcomputer sends control signal to power off the relay. At last, the waveform of the residual voltage is displayed on a principal computer or oscilloscope. The experimental results show that the device designed in this paper can turn the power off at peak voltage and is able to accurately display the voltage waveform immediately after power off and the standard deviation of the residual voltage is less than 0.2 V at exactly one second and later.

  18. Bayesian nonparametric regression with varying residual density

    PubMed Central

    Pati, Debdeep; Dunson, David B.

    2013-01-01

    We consider the problem of robust Bayesian inference on the mean regression function allowing the residual density to change flexibly with predictors. The proposed class of models is based on a Gaussian process prior for the mean regression function and mixtures of Gaussians for the collection of residual densities indexed by predictors. Initially considering the homoscedastic case, we propose priors for the residual density based on probit stick-breaking (PSB) scale mixtures and symmetrized PSB (sPSB) location-scale mixtures. Both priors restrict the residual density to be symmetric about zero, with the sPSB prior more flexible in allowing multimodal densities. We provide sufficient conditions to ensure strong posterior consistency in estimating the regression function under the sPSB prior, generalizing existing theory focused on parametric residual distributions. The PSB and sPSB priors are generalized to allow residual densities to change nonparametrically with predictors through incorporating Gaussian processes in the stick-breaking components. This leads to a robust Bayesian regression procedure that automatically down-weights outliers and influential observations in a locally-adaptive manner. Posterior computation relies on an efficient data augmentation exact block Gibbs sampler. The methods are illustrated using simulated and real data applications. PMID:24465053

  19. Model-checking techniques based on cumulative residuals.

    PubMed

    Lin, D Y; Wei, L J; Ying, Z

    2002-03-01

    Residuals have long been used for graphical and numerical examinations of the adequacy of regression models. Conventional residual analysis based on the plots of raw residuals or their smoothed curves is highly subjective, whereas most numerical goodness-of-fit tests provide little information about the nature of model misspecification. In this paper, we develop objective and informative model-checking techniques by taking the cumulative sums of residuals over certain coordinates (e.g., covariates or fitted values) or by considering some related aggregates of residuals, such as moving sums and moving averages. For a variety of statistical models and data structures, including generalized linear models with independent or dependent observations, the distributions of these stochastic processes tinder the assumed model can be approximated by the distributions of certain zero-mean Gaussian processes whose realizations can be easily generated by computer simulation. Each observed process can then be compared, both graphically and numerically, with a number of realizations from the Gaussian process. Such comparisons enable one to assess objectively whether a trend seen in a residual plot reflects model misspecification or natural variation. The proposed techniques are particularly useful in checking the functional form of a covariate and the link function. Illustrations with several medical studies are provided.

  20. Bioinformatic prediction and in vivo validation of residue-residue interactions in human proteins

    NASA Astrophysics Data System (ADS)

    Jordan, Daniel; Davis, Erica; Katsanis, Nicholas; Sunyaev, Shamil

    2014-03-01

    Identifying residue-residue interactions in protein molecules is important for understanding both protein structure and function in the context of evolutionary dynamics and medical genetics. Such interactions can be difficult to predict using existing empirical or physical potentials, especially when residues are far from each other in sequence space. Using a multiple sequence alignment of 46 diverse vertebrate species we explore the space of allowed sequences for orthologous protein families. Amino acid changes that are known to damage protein function allow us to identify specific changes that are likely to have interacting partners. We fit the parameters of the continuous-time Markov process used in the alignment to conclude that these interactions are primarily pairwise, rather than higher order. Candidates for sites under pairwise epistasis are predicted, which can then be tested by experiment. We report the results of an initial round of in vivo experiments in a zebrafish model that verify the presence of multiple pairwise interactions predicted by our model. These experimentally validated interactions are novel, distant in sequence, and are not readily explained by known biochemical or biophysical features.

  1. 40 CFR 180.229 - Fluometuron; tolerances for residues.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... combined residues of the herbicide fluometuron, N, N-dimethyl-N'-[3-(trifluoromethyl)phenyl]urea, and its... established for the combined residues of the herbicide fluometuron, N,N-dimethyl-N'-[3-(trifluoromethyl)phenyl... established for the combined residues of the herbicide fluometuron, N, N-dimethyl-N'-[3-(trifluoromethyl...

  2. 40 CFR 180.229 - Fluometuron; tolerances for residues.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... combined residues of the herbicide fluometuron, N, N-dimethyl-N'-[3-(trifluoromethyl)phenyl]urea, and its... established for the combined residues of the herbicide fluometuron, N,N-dimethyl-N'-[3-(trifluoromethyl)phenyl... established for the combined residues of the herbicide fluometuron, N, N-dimethyl-N'-[3-(trifluoromethyl...

  3. 40 CFR 180.659 - Pyroxasulfone; tolerances for residues.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... residues of the herbicide pyroxasulfone, including its metabolites and degradates, in or on the commodities... established for residues of the herbicide pyroxasulfone, including its metabolites and degradates, in or on... Soybean, hay 2.0 (3) Tolerances are established for residues of the herbicide pyroxasulfone, including its...

  4. 40 CFR 180.317 - Propyzamide; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... residues of the herbicide propyzamide and its metabolites (containing the 3,5-dichlorobenzoyl moiety... tolerances are established for the combined residues of the herbicide propyzamide and its metabolites..., as defined in § 180.1(m) are established for the combined residues of the herbicide propyzamide and...

  5. 40 CFR 180.229 - Fluometuron; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... combined residues of the herbicide fluometuron, N, N-dimethyl-N'-[3-(trifluoromethyl)phenyl]urea, and its... established for the combined residues of the herbicide fluometuron, N,N-dimethyl-N'-[3-(trifluoromethyl)phenyl... established for the combined residues of the herbicide fluometuron, N, N-dimethyl-N'-[3-(trifluoromethyl...

  6. 40 CFR 180.229 - Fluometuron; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... combined residues of the herbicide fluometuron, N, N-dimethyl-N'-[3-(trifluoromethyl)phenyl]urea, and its... established for the combined residues of the herbicide fluometuron, N,N-dimethyl-N'-[3-(trifluoromethyl)phenyl... established for the combined residues of the herbicide fluometuron, N, N-dimethyl-N'-[3-(trifluoromethyl...

  7. 40 CFR 180.229 - Fluometuron; tolerances for residues.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... combined residues of the herbicide fluometuron, N, N-dimethyl-N'-[3-(trifluoromethyl)phenyl]urea, and its... established for the combined residues of the herbicide fluometuron, N,N-dimethyl-N'-[3-(trifluoromethyl)phenyl... established for the combined residues of the herbicide fluometuron, N, N-dimethyl-N'-[3-(trifluoromethyl...

  8. Detecting Multidimensionality: Which Residual Data-Type Works Best?

    ERIC Educational Resources Information Center

    Linacre, John Michael

    1998-01-01

    Simulation studies indicate that, for responses to complete tests, construction of Rasch measures from observational data, followed by principal components factor analysis of Rasch residuals, provides an effective means of identifying multidimensionality. The most diagnostically useful residual form was found to be the standardized residual. (SLD)

  9. 40 CFR 180.574 - Fluazinam; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 24 2011-07-01 2011-07-01 false Fluazinam; tolerances for residues... § 180.574 Fluazinam; tolerances for residues. (a) General. (1) Tolerances are established for residues of fluazinam (3-chloro-N-[3-chloro-2,6-dinitro-4-(trifluoromethyl)phenyl]-5-(trifluoromethyl)-2...

  10. Managing woodwaste: Yield from residue

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Nielson, E.; Rayner, S.

    1993-12-31

    Historically, the majority of sawmill waste has been burned or buried for the sole purpose of disposal. In most jurisdictions, environmental legislation will prohibit, or render uneconomic, these practices. Many reports have been prepared to describe the forest industry`s residue and its environmental effect; although these help those looking for industry-wide or regional solutions, such as electricity generation, they have limited value for the mill manager, who has the on-hands responsibility for generation and disposal of the waste. If the mill manager can evaluate waste streams and break them down into their usable components, he can find niche market solutionsmore » for portions of the plant residue and redirect waste to poor/no-return, rather than disposal-cost, end uses. In the modern mill, residue is collected at the individual machine centre by waste conveyors that combine and mix sawdust, shavings, bark, etc. and send the result to the hog-fuel pile. The mill waste system should be analyzed to determine the measures that can improve the quality of residues and determine the volumes of any particular category before the mixing, mentioned above, occurs. After this analysis, the mill may find a niche market for a portion of its woodwaste.« less

  11. Bio-knowledge based filters improve residue-residue contact prediction accuracy.

    PubMed

    Wozniak, P P; Pelc, J; Skrzypecki, M; Vriend, G; Kotulska, M

    2018-05-29

    Residue-residue contact prediction through direct coupling analysis has reached impressive accuracy, but yet higher accuracy will be needed to allow for routine modelling of protein structures. One way to improve the prediction accuracy is to filter predicted contacts using knowledge about the particular protein of interest or knowledge about protein structures in general. We focus on the latter and discuss a set of filters that can be used to remove false positive contact predictions. Each filter depends on one or a few cut-off parameters for which the filter performance was investigated. Combining all filters while using default parameters resulted for a test-set of 851 protein domains in the removal of 29% of the predictions of which 92% were indeed false positives. All data and scripts are available from http://comprec-lin.iiar.pwr.edu.pl/FPfilter/. malgorzata.kotulska@pwr.edu.pl. Supplementary data are available at Bioinformatics online.

  12. RECOVERY OF URANIUM VALUES FROM RESIDUES

    DOEpatents

    Schaap, W.B.

    1959-08-18

    A process is described for the recovery of uranium from insoluble oxide residues resistant to repeated leaching with mineral acids. The residue is treated with gaseous hydrogen fluoride, then with hydrogen and again with hydrogen fluoride, preferably at 500 to 700 deg C, prior to the mineral acid leaching.

  13. 40 CFR 180.501 - Hydroprene; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Hydroprene; tolerances for residues. 180.501 Section 180.501 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.501 Hydroprene; tolerances for residues. (a)...

  14. 40 CFR 161.240 - Residue chemistry data requirements.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Residue chemistry data requirements... § 161.240 Residue chemistry data requirements. (a) Table. Sections 161.100 through 161.102 describe how to use this table to determine the residue chemistry data requirements and the substances to be...

  15. 20 CFR 225.26 - Residual Lump-Sum PIA.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ..., except that social security earnings are not used to compute the RLS PIA. ... INSURANCE AMOUNT DETERMINATIONS PIA's Used in Computing Survivor Annuities and the Amount of the Residual Lump-Sum Payable § 225.26 Residual Lump-Sum PIA. The Residual Lump-Sum PIA (RLS PIA) is used to compute...

  16. 40 CFR 161.240 - Residue chemistry data requirements.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 25 2013-07-01 2013-07-01 false Residue chemistry data requirements... § 161.240 Residue chemistry data requirements. (a) Table. Sections 161.100 through 161.102 describe how to use this table to determine the residue chemistry data requirements and the substances to be...

  17. 40 CFR 161.240 - Residue chemistry data requirements.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 24 2011-07-01 2011-07-01 false Residue chemistry data requirements... § 161.240 Residue chemistry data requirements. (a) Table. Sections 161.100 through 161.102 describe how to use this table to determine the residue chemistry data requirements and the substances to be...

  18. 40 CFR 161.240 - Residue chemistry data requirements.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 25 2012-07-01 2012-07-01 false Residue chemistry data requirements... § 161.240 Residue chemistry data requirements. (a) Table. Sections 161.100 through 161.102 describe how to use this table to determine the residue chemistry data requirements and the substances to be...

  19. Residual stresses in cross-ply composite tubes

    NASA Technical Reports Server (NTRS)

    Cohen, D.; Hyer, M. W.

    1984-01-01

    The residual thermal stresses in 4-layer cross-ply tubes are studied. The tubes considered has a small radius to wall-thickness ratios and so elasticity solutions were used. The residual thermal stress problem was considered to be axisymmetric and three elasticity solutions were derived and the results compared with the results using classical lamination theory. The comparison illustrates the limitations of classical lamination theory. The three elasticity solutions derived were: plane stress, plane strain, and generalized plane strain, the latter being the most realistic. Residual stresses in both the hoop and axial direction is significant. Stacking arrangement effects the residual stress to some extent, as do the material properties of the individual lamina. The benefits of hybrid construction are briefly discussed.

  20. The Residual Risk Reduction Initiative: a call to action to reduce residual vascular risk in patients with dyslipidemia.

    PubMed

    Fruchart, Jean-Charles; Sacks, Frank; Hermans, Michel P; Assmann, Gerd; Brown, W Virgil; Ceska, Richard; Chapman, M John; Dodson, Paul M; Fioretto, Paola; Ginsberg, Henry N; Kadowaki, Takashi; Lablanche, Jean-Marc; Marx, Nikolaus; Plutzky, Jorge; Reiner, Zeljko; Rosenson, Robert S; Staels, Bart; Stock, Jane K; Sy, Rody; Wanner, Christoph; Zambon, Alberto; Zimmet, Paul

    2008-11-17

    Despite achieving targets for low-density lipoprotein (LDL) cholesterol, blood pressure, and glycemia in accordance with current standards of care, patients with dyslipidemia remain at high residual risk of vascular events. Atherogenic dyslipidemia, characterized by elevated triglycerides and low levels of high-density lipoprotein (HDL) cholesterol, often with elevated apolipoprotein B and non-HDL cholesterol, is common in patients with established cardiovascular disease (CVD), type 2 diabetes mellitus, or metabolic syndrome and contributes to both macrovascular and microvascular residual risk. However, atherogenic dyslipidemia is largely underdiagnosed and undertreated in clinical practice. The Residual Risk Reduction Initiative (R3i) was established to address this highly relevant clinical issue. The aims of this position paper are (1) to highlight evidence that atherogenic dyslipidemia is associated with residual macrovascular and microvascular risk in patients at high risk for CVD, despite current standards of care for dyslipidemia and diabetes; and (2) to recommend therapeutic intervention for reducing this residual vascular risk supported by evidence and expert consensus. Lifestyle modification with nutrition and exercise is an important, effective, and underutilized first step in reducing residual vascular risk. Therapeutic intervention aimed at achievement of all lipid targets is also often required. Combination lipid-modifying therapy, with the addition of niacin, a fibrate, or omega-3 fatty acids to statin therapy, increases the probability of achieving all lipid goals. Outcomes studies are in progress to evaluate whether these combination treatment strategies translate to a clinical benefit greater than that achieved with statins alone. The R3i highlights the need to address with lifestyle and/or pharmacotherapy the high level of residual risk of CVD events and microvascular complications among patients with dyslipidemia receiving therapy for high levels

  1. Optical systolic array processor using residue arithmetic

    NASA Technical Reports Server (NTRS)

    Jackson, J.; Casasent, D.

    1983-01-01

    The use of residue arithmetic to increase the accuracy and reduce the dynamic range requirements of optical matrix-vector processors is evaluated. It is determined that matrix-vector operations and iterative algorithms can be performed totally in residue notation. A new parallel residue quantizer circuit is developed which significantly improves the performance of the systolic array feedback processor. Results are presented of a computer simulation of this system used to solve a set of three simultaneous equations.

  2. Endosulfan in China 2-emissions and residues.

    PubMed

    Jia, Hongliang; Sun, Yeqing; Li, Yi-Fan; Tian, Chongguo; Wang, Degao; Yang, Meng; Ding, Yongshen; Ma, Jianmin

    2009-05-01

    Endosulfan is one of the organochlorine pesticides (OCPs) and also a candidate to be included in a group of new persistent organic pollutants (UNEP 2007). The first national endosulfan usage inventories in China with 1/4 degrees longitude by 1/6 degrees latitude resolution has been reported in an accompanying paper. In the second part of the paper, we compiled the gridded historical emissions and soil residues of endosulfan in China from the usage inventories. Based on the residue/emission data, gridded concentrations of endosulfan in Chinese soil and air have been calculated. These inventories will provide valuable data for the further study of endosulfan. Emission and residue of endosulfan were calculated from endosulfan usage by using a simplified gridded pesticide emission and residue model-SGPERM, which is an integrated modeling system combining mathematical model, database management system, and geographic information system. By using the emission and residue inventories, annual air and soil concentrations of endosulfan in each cell were determined. Historical gridded emission and residue inventories of alpha- and beta-endosulfan in agricultural soil in China with 1/4 degrees longitude by 1/6 degrees latitude resolution have been created. Total emissions were around 10,800 t, with alpha-endosulfan at 7,400 t and beta-endosulfan at 3,400 t from 1994 to 2004. The highest residues were 140 t for alpha-endosulfan and 390 t for beta-endosulfan, and the lowest residues were 0.7 t for alpha-endosulfan and 170 t for beta-endosulfan in 2004 in Chinese agricultural soil where endosulfan was applied. Based on the emission and residue inventories, concentrations of alpha- and beta-endosulfan in Chinese air and agricultural surface soil were also calculated for each grid cell. We have estimated annual averaged air concentrations and the annual minimum and maximum soil concentrations across China. The real concentrations will be different from season to season. Although

  3. Residue depletion of tilmicosin in chicken tissues.

    PubMed

    Zhang, Yue; Jiang, Haiyang; Jin, Xingjun; Shen, Zhangqi; Shen, Jianzhong; Fu, Caixia; Guo, Junlin

    2004-05-05

    A high-performance liquid chromatography (HPLC) method with detection at 290 nm was modified and validated for the determination of tilmicosin residues in broiler chicken tissues. The limits of detection (LOD) of the method were 0.01 microg/g for muscle and 0.025 microg/g for liver and kidney. Average recoveries ranged from 80.4 to 88.3%. Relative standard deviation values ranged from 5.2 to 12.1%. Residue depletion of tilmicosin in broiler chickens was examined after dosing over a 5-day period by incorporation of the drug into drinking water at 37.5 and 75.0 mg/L. Tilmicosin concentrations in liver and kidney were highest on day 3 of medication and on day 5 in muscle, in both low- and high-dose groups. The residue levels in both groups were significantly higher in liver than in kidney or muscle. A minimum withdrawal time of 9 days was indicated for residue levels in muscle, liver, and kidney tissues below the maximum residue level (MRL).

  4. 40 CFR 180.505 - Emamectin; tolerances for residues.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 25 2012-07-01 2012-07-01 false Emamectin; tolerances for residues... § 180.505 Emamectin; tolerances for residues. (a) General. (1) Tolerances are established for combined residues of emamectin (a mixture of a minimum of 90% 4′-epi-methylamino-4′-deoxyavermectin B1a and maximum...

  5. Selecting forest residue treatment alternatives using goal programming.

    Treesearch

    Bruce B. Bare; Brian F. Anholt

    1976-01-01

    The use of goal programing for selecting forest residue treatment alternatives within a multiple goal framework is described. The basic features of goal programing are reviewed and illustrated with a hypothetical problem involving the selection of residue treatments for 10 cutting units. Twelve residue-regeneration treatment combinations are evaluated by using physical...

  6. Dry fermentation of agricultural residues

    NASA Astrophysics Data System (ADS)

    Jewell, W. J.; Chandler, J. A.; Dellorto, S.; Fanfoni, K. J.; Fast, S.; Jackson, D.; Kabrick, R. M.

    1981-09-01

    A dry fermentation process is discussed which converts agricultural residues to methane, using the residues in their as produced state. The process appears to simplify and enhance the possibilities for using crop residues as an energy source. The major process variables investigated include temperature, the amount and type of inoculum, buffer requirements, compaction, and pretreatment to control the initial available organic components that create pH problems. A pilot-scale reactor operation on corn stover at a temperature of 550 C, with 25 percent initial total solids, a seed-to-feed ratio of 2.5 percent, and a buffer-to-feed ratio of 8 percent achieved 33 percent total volatile solids destruction in 60 days. Volumetric biogas yields from this unit were greater than 1 vol/vol day for 12 days, and greater than 0.5 vol/vol day for 32 days, at a substrate density of 169 kg/m (3).

  7. Adsorption Property and Mechanism of Oxytetracycline onto Willow Residues

    PubMed Central

    Wang, Di; Xu, Haiyang; Yang, Shengke; Wang, Wenke; Wang, Yanhua

    2017-01-01

    To elucidate the adsorption property and the mechanism of plant residues to reduce oxytetracycline (OTC), the adsorption of OTC onto raw willow roots (WR-R), stems (WS-R), leaves (WL-R), and adsorption onto desugared willow roots (WR-D), stems (WS-D), and leaves (WL-D) were investigated. The structural characterization was analyzed by scanning electron microscopy, Fourier-transform infrared spectra, and an elemental analyzer. OTC adsorption onto the different tissues of willow residues was compared and correlated with their structures. The adsorption kinetics of OTC onto willow residues was found to follow the pseudo-first-order model. The isothermal adsorption process of OTC onto the different tissues of willow residues followed the Langmuir and Freundlich model and the process was also a spontaneous endothermic reaction, which was mainly physical adsorption. After the willow residues were desugared, the polarity decreased and the aromaticity increased, which explained why the adsorption amounts of the desugared willow residues were higher than those of the unmodified residues. These observations suggest that the raw and modified willow residues have great potential as adsorbents to remove organic pollutants. PMID:29271892

  8. Glyphosate fate in soils when arriving in plant residues.

    PubMed

    Mamy, Laure; Barriuso, Enrique; Gabrielle, Benoît

    2016-07-01

    A significant fraction of pesticides sprayed on crops may be returned to soils via plant residues, but its fate has been little documented. The objective of this work was to study the fate of glyphosate associated to plants residues. Oilseed rape was used as model plant using two lines: a glyphosate-tolerant (GT) line and a non-GT one, considered as a crucifer weed. The effects of different fragmentation degrees and placements in soil of plant residues were tested. A control was set up by spraying glyphosate directly on the soil. The mineralization of glyphosate in soil was slower when incorporated into plant residues, and the amounts of extractable and non-extractable glyphosate residues increased. Glyphosate availability for mineralization increased when the size of plant residues decreased, and as the distribution of plant residues in soil was more homogeneous. After 80 days of soil incubation, extractable (14)C-residues mostly involved one metabolite of glyphosate (AMPA) but up to 2.6% of initial (14)C was still extracted from undecayed leaves as glyphosate. Thus, the trapping of herbicides in plant materials provided a protection against degradation, and crops residues returns may increase the persistence of glyphosate in soils. This pattern appeared more pronounced for GT crops, which accumulated more non-degraded glyphosate in their tissues. Copyright © 2016 Elsevier Ltd. All rights reserved.

  9. Interpretation on Recycling Plastics from Shredder Residue

    EPA Pesticide Factsheets

    EPA is considering an interpretation of its regulations that would generally allow for recycling of plastic separated from shredder residue under the conditions described in the Voluntary Procedures for Recycling Plastics from Shredder Residue.

  10. Soil water evaporation and crop residues

    USDA-ARS?s Scientific Manuscript database

    Crop residues have value when left in the field and also when removed from the field and sold as a commodity. Reducing soil water evaporation (E) is one of the benefits of leaving crop residues in place. E was measured beneath a corn canopy at the soil suface with nearly full coverage by corn stover...

  11. CSmetaPred: a consensus method for prediction of catalytic residues.

    PubMed

    Choudhary, Preeti; Kumar, Shailesh; Bachhawat, Anand Kumar; Pandit, Shashi Bhushan

    2017-12-22

    Knowledge of catalytic residues can play an essential role in elucidating mechanistic details of an enzyme. However, experimental identification of catalytic residues is a tedious and time-consuming task, which can be expedited by computational predictions. Despite significant development in active-site prediction methods, one of the remaining issues is ranked positions of putative catalytic residues among all ranked residues. In order to improve ranking of catalytic residues and their prediction accuracy, we have developed a meta-approach based method CSmetaPred. In this approach, residues are ranked based on the mean of normalized residue scores derived from four well-known catalytic residue predictors. The mean residue score of CSmetaPred is combined with predicted pocket information to improve prediction performance in meta-predictor, CSmetaPred_poc. Both meta-predictors are evaluated on two comprehensive benchmark datasets and three legacy datasets using Receiver Operating Characteristic (ROC) and Precision Recall (PR) curves. The visual and quantitative analysis of ROC and PR curves shows that meta-predictors outperform their constituent methods and CSmetaPred_poc is the best of evaluated methods. For instance, on CSAMAC dataset CSmetaPred_poc (CSmetaPred) achieves highest Mean Average Specificity (MAS), a scalar measure for ROC curve, of 0.97 (0.96). Importantly, median predicted rank of catalytic residues is the lowest (best) for CSmetaPred_poc. Considering residues ranked ≤20 classified as true positive in binary classification, CSmetaPred_poc achieves prediction accuracy of 0.94 on CSAMAC dataset. Moreover, on the same dataset CSmetaPred_poc predicts all catalytic residues within top 20 ranks for ~73% of enzymes. Furthermore, benchmarking of prediction on comparative modelled structures showed that models result in better prediction than only sequence based predictions. These analyses suggest that CSmetaPred_poc is able to rank putative catalytic

  12. Sedentary behavior and residual-specific mortality

    PubMed Central

    Loprinzi, Paul D.; Edwards, Meghan K.; Sng, Eveleen; Addoh, Ovuokerie

    2016-01-01

    Background: The purpose of this study was to examine the association of accelerometer-assessed sedentary behavior and residual-specific mortality. Methods: Data from the 2003-2006 National Health and Nutrition Examination Survey (NHANES) were used (N = 5536), with follow-up through 2011. Sedentary behavior was objectively measured over 7 days via accelerometry. Results: When expressing sedentary behavior as a 60 min/day increase, the hazard ratio across the models ranged from 1.07-1.40 (P < 0.05). There was evidence of an interaction effect between sedentary behavior and total physical activity on residual-specific mortality (Hazard ratiointeraction [HR] = 0.9989; 95% CI: 0.9982-0.9997; P = 0.008). Conclusion: Sedentary behavior was independently associated with residual-specific mortality. However, there was evidence to suggest that residual-specific mortality risk was a function of sedentary behavior and total physical activity. These findings highlight the need for future work to not only examine the association between sedentary behavior and health independent of total physical activity, but evaluate whether there is a joint effect of these two parameters on health. PMID:27766237

  13. 40 CFR 180.573 - Tepraloxydim; tolerances for residues.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... combined residues of tepraloxydim, (2-[1-[[[(2E)-3-chloro-2-propen-1-yl]oxy]imino]propyl]-3-hydroxy-5... combined residues of tepraloxydim (2-[1-[[[(2E)-3-chloro-2-propen-1-yl]oxy]imino]propyl]-3-hydroxy-5... is to be determined by measuring only the combined residues of tepraloxydim (2-[1-[[[(2E)-3-chloro-2...

  14. 40 CFR 180.573 - Tepraloxydim; tolerances for residues.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... combined residues of tepraloxydim, (2-[1-[[[(2E)-3-chloro-2-propen-1-yl]oxy]imino]propyl]-3-hydroxy-5... combined residues of tepraloxydim (2-[1-[[[(2E)-3-chloro-2-propen-1-yl]oxy]imino]propyl]-3-hydroxy-5... is to be determined by measuring only the combined residues of tepraloxydim (2-[1-[[[(2E)-3-chloro-2...

  15. 40 CFR 180.573 - Tepraloxydim; tolerances for residues.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... combined residues of tepraloxydim, (2-[1-[[[(2E)-3-chloro-2-propen-1-yl]oxy]imino]propyl]-3-hydroxy-5... combined residues of tepraloxydim (2-[1-[[[(2E)-3-chloro-2-propen-1-yl]oxy]imino]propyl]-3-hydroxy-5... is to be determined by measuring only the combined residues of tepraloxydim (2-[1-[[[(2E)-3-chloro-2...

  16. Estimators and characteristics of logging residue in Montana.

    Treesearch

    James. O Howard; Carl E. Fiedler

    1984-01-01

    Ratios are presented for estimating volume and characteristics of logging residue in Montana. They relate cubic-foot volume of residue to thousand board feet of timber harvested and to acres harvested. Tables show gross and net volume of residue, with and without bark, by diameter and length classes; by number of pieces per acre; by percent soundness; by product...

  17. 40 CFR 180.390 - Tebuthiuron; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... combined residues of the herbicide tebuthiuron (N-(5-(1,1-dimethylethyl)-1,3,4-thiadiazol-2-yl)-N,N... residues of the herbicide tebuthiuron (N-(5-(1,1-dimethylethyl)-1,3,4-thiadiazol-2-yl)-N,N'-dimethylurea... combined residues of the herbicide tebuthiuron (N-(5-(1,1-dimethylethyl)-1,3,4-thiadiazol-2-yl)-N,N...

  18. 40 CFR 180.458 - Clethodim; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... combined residues of the herbicide clethodim ((E)-(±)-2-[1-[[(3-chloro-2-propenyl)oxy]imino]propyl]-5-[2...) Tolerances are established for the combined residues of the herbicide clethodim [(E)-(±)-2-[1-[[(3-chloro-2... residues of the herbicide clethodim ((E)-(±)-2-[1-[[(3-chloro-2-propenyl)oxy]imino]propyl]-5-[2-(ethylthio...

  19. 40 CFR 180.390 - Tebuthiuron; tolerances for residues.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... combined residues of the herbicide tebuthiuron (N-(5-(1,1-dimethylethyl)-1,3,4-thiadiazol-2-yl)-N,N... residues of the herbicide tebuthiuron (N-(5-(1,1-dimethylethyl)-1,3,4-thiadiazol-2-yl)-N,N'-dimethylurea... combined residues of the herbicide tebuthiuron (N-(5-(1,1-dimethylethyl)-1,3,4-thiadiazol-2-yl)-N,N...

  20. 40 CFR 180.390 - Tebuthiuron; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... combined residues of the herbicide tebuthiuron (N-(5-(1,1-dimethylethyl)-1,3,4-thiadiazol-2-yl)-N,N... residues of the herbicide tebuthiuron (N-(5-(1,1-dimethylethyl)-1,3,4-thiadiazol-2-yl)-N,N'-dimethylurea... combined residues of the herbicide tebuthiuron (N-(5-(1,1-dimethylethyl)-1,3,4-thiadiazol-2-yl)-N,N...

  1. 40 CFR 180.390 - Tebuthiuron; tolerances for residues.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... combined residues of the herbicide tebuthiuron (N-(5-(1,1-dimethylethyl)-1,3,4-thiadiazol-2-yl)-N,N... residues of the herbicide tebuthiuron (N-(5-(1,1-dimethylethyl)-1,3,4-thiadiazol-2-yl)-N,N'-dimethylurea... combined residues of the herbicide tebuthiuron (N-(5-(1,1-dimethylethyl)-1,3,4-thiadiazol-2-yl)-N,N...

  2. 40 CFR 180.390 - Tebuthiuron; tolerances for residues.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... combined residues of the herbicide tebuthiuron (N-(5-(1,1-dimethylethyl)-1,3,4-thiadiazol-2-yl)-N,N... residues of the herbicide tebuthiuron (N-(5-(1,1-dimethylethyl)-1,3,4-thiadiazol-2-yl)-N,N'-dimethylurea... combined residues of the herbicide tebuthiuron (N-(5-(1,1-dimethylethyl)-1,3,4-thiadiazol-2-yl)-N,N...

  3. On the structural context and identification of enzyme catalytic residues.

    PubMed

    Chien, Yu-Tung; Huang, Shao-Wei

    2013-01-01

    Enzymes play important roles in most of the biological processes. Although only a small fraction of residues are directly involved in catalytic reactions, these catalytic residues are the most crucial parts in enzymes. The study of the fundamental and unique features of catalytic residues benefits the understanding of enzyme functions and catalytic mechanisms. In this work, we analyze the structural context of catalytic residues based on theoretical and experimental structure flexibility. The results show that catalytic residues have distinct structural features and context. Their neighboring residues, whether sequence or structure neighbors within specific range, are usually structurally more rigid than those of noncatalytic residues. The structural context feature is combined with support vector machine to identify catalytic residues from enzyme structure. The prediction results are better or comparable to those of recent structure-based prediction methods.

  4. [Study on the histological anatomy on medicinal parts of Semiaquilegia adoxoides in different developmental stages].

    PubMed

    Yang, Jun; Peng, Hua-Sheng; Wang, De-Qun; Sun, Jing

    2012-08-01

    To study the structural characteristics of medicinal parts at different developmental stages of Semiaquilegia adoxoides. Observed on sections of medicinal parts of Semiaquilegia adoxoides at various developmental stages during growth periods. There was a great difference between the upper and bottom of the medicinal parts of Semiaquilegia adoxoides: rhizome at the top of root had the structure of rhizome with pith; The upper one third of enlarged root was root-stem transition zone, also with pith; And the other two thirds of enlarged root had the structure of root without pith. The microscopic structures of the medicinal parts of Semiaquilegia adoxoides at various developmental stages presented great disparities, the structures regularly increased as the size of plant increased. It was the first time to find that there were structure of growth rings in xylem of the root and rhizome of Semiaquilegia adoxoides. The method of identification of characteristics and histology of medicinal parts of Semiaquilegia adoxoides at different developmental stages is established, and the results provide a basis for identification of Semiaquilegia adoxoides medicinal materials.

  5. In-situ method for treating residual sodium

    DOEpatents

    Sherman, Steven R.; Henslee, S. Paul

    2005-07-19

    A unique process for deactivating residual sodium in Liquid Metal Fast Breeder Reactor (LMFBR) systems which uses humidified (but not saturated) carbon dioxide at ambient temperature and pressure to convert residual sodium into solid sodium bicarbonate.

  6. In-Situ Method for Treating Residual Sodium

    DOEpatents

    Sherman, Steven R.; Henslee, S. Paul

    2005-07-19

    A unique process for deactivating residual sodium in Liquid Metal Fast Breeder Reactor (LMFBR) systems which uses humidified (but not saturated) carbon dioxide at ambient temperature and pressure to convert residual sodium into solid sodium bicarbonate.

  7. Estimators and characteristics of logging residue in California.

    Treesearch

    James O. Howard; Julianne K. Bulgrin

    1986-01-01

    Ratios are presented for estimating volume and characteristics of logging residue in California. The ratios relate cubic-foot volume of residue to thousand board feet of timber harvested and to acres harvested. Tables show gross and net volume of residue, with and without bark, by diameter and length classes, by number of pieces per acre, by softwoods and hardwoods, by...

  8. Residual gravimetric method to measure nebulizer output.

    PubMed

    Vecellio None, Laurent; Grimbert, Daniel; Bordenave, Joelle; Benoit, Guy; Furet, Yves; Fauroux, Brigitte; Boissinot, Eric; De Monte, Michele; Lemarié, Etienne; Diot, Patrice

    2004-01-01

    The aim of this study was to assess a residual gravimetric method based on weighing dry filters to measure the aerosol output of nebulizers. This residual gravimetric method was compared to assay methods based on spectrophotometric measurement of terbutaline (Bricanyl, Astra Zeneca, France), high-performance liquid chromatography (HPLC) measurement of tobramycin (Tobi, Chiron, U.S.A.), and electrochemical measurements of NaF (as defined by the European standard). Two breath-enhanced jet nebulizers, one standard jet nebulizer, and one ultrasonic nebulizer were tested. Output produced by the residual gravimetric method was calculated by weighing the filters both before and after aerosol collection and by filter drying corrected by the proportion of drug contained in total solute mass. Output produced by the electrochemical, spectrophotometric, and HPLC methods was determined after assaying the drug extraction filter. The results demonstrated a strong correlation between the residual gravimetric method (x axis) and assay methods (y axis) in terms of drug mass output (y = 1.00 x -0.02, r(2) = 0.99, n = 27). We conclude that a residual gravimetric method based on dry filters, when validated for a particular agent, is an accurate way of measuring aerosol output.

  9. Quantile based Tsallis entropy in residual lifetime

    NASA Astrophysics Data System (ADS)

    Khammar, A. H.; Jahanshahi, S. M. A.

    2018-02-01

    Tsallis entropy is a generalization of type α of the Shannon entropy, that is a nonadditive entropy unlike the Shannon entropy. Shannon entropy may be negative for some distributions, but Tsallis entropy can always be made nonnegative by choosing appropriate value of α. In this paper, we derive the quantile form of this nonadditive's entropy function in the residual lifetime, namely the residual quantile Tsallis entropy (RQTE) and get the bounds for it, depending on the Renyi's residual quantile entropy. Also, we obtain relationship between RQTE and concept of proportional hazards model in the quantile setup. Based on the new measure, we propose a stochastic order and aging classes, and study its properties. Finally, we prove characterizations theorems for some well known lifetime distributions. It is shown that RQTE uniquely determines the parent distribution unlike the residual Tsallis entropy.

  10. Residual Stresses in 21-6-9 Stainless Steel Warm Forgings

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Everhart, Wesley A.; Lee, Jordan D.; Broecker, Daniel J.

    Forging residual stresses are detrimental to the production and performance of derived machined parts due to machining distortions, corrosion drivers and fatigue crack drivers. Residual strains in a 21-6-9 stainless steel warm High Energy Rate Forging (HERF) were measured via neutron diffraction. The finite element analysis (FEA) method was used to predict the residual stresses that occur during forging and water quenching. The experimentally measured residual strains were used to calibrate simulations of the three-dimensional residual stress state of the forging. ABAQUS simulation tools predicted residual strains that tend to match with experimental results when varying yield strength is considered.

  11. 40 CFR 180.499 - Propamocarb hydrochloride, tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... for residues. 180.499 Section 180.499 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.499 Propamocarb hydrochloride, tolerances for residues. (a) General. Tolerances are...

  12. 40 CFR 180.499 - Propamocarb hydrochloride, tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... for residues. 180.499 Section 180.499 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.499 Propamocarb hydrochloride, tolerances for residues. (a) General. Tolerances are...

  13. Uptake and distribution of chlordecone in radish: different contamination routes in edible roots.

    PubMed

    Létondor, Clarisse; Pascal-Lorber, Sophie; Laurent, François

    2015-01-01

    Chlordecone (CLD) was an organochlorine insecticide mainly used to struggle against banana weevils in the French West Indies. Forbidden since 1993, it has been a long-term contaminant of soils and aquatic environments. Crops growing in contaminated soils lead to human exposure by food consumption. We used radiolabeled [(14)C]-CLD to investigate the contamination ways into radish, a model of edible roots. Radish plants were able to accumulate CLD in both roots (RCF35d 647) and tubers (edible parts, CF35d 6.3). CLD was also translocated to leaves (CF35d 1.7). The contamination of tuber was mainly due to peridermic adsorption or CLD systemic translocation to the pith. TSCF was 3.44×10(-)(3). CLD diffused across periderm to internal tissues. We calculated a mean flux of diffusion J through periderm about 5.71×10(-)(14)gcm(-)(2)s(-)(1). We highlighted different contamination routes of the tuber, (i) adsorption on periderm followed by diffusion of CLD towards underlying tissues, cortex, xylem, and pith (ii) adsorption by roots and translocation by the transpiration stream followed by diffusion from xylem vessels towards inner tissues, pith, and peripheral tissues, cortex and periderm. Concerning chemical risk assessment for other tubers, contamination would depend on various parameters, the thickness of periderm and CLD periderm permeance, the origin of secondary tissues - from cortex and/or pith - , the importance of xylem flow in tuber, and the lipid amount within tuber. Copyright © 2014 Elsevier Ltd. All rights reserved.

  14. XTH20 and XTH19 regulated by ANAC071 under auxin flow are involved in cell proliferation in incised Arabidopsis inflorescence stems.

    PubMed

    Pitaksaringkarn, Weerasak; Matsuoka, Keita; Asahina, Masashi; Miura, Kenji; Sage-Ono, Kimiyo; Ono, Michiyuki; Yokoyama, Ryusuke; Nishitani, Kazuhiko; Ishii, Tadashi; Iwai, Hiroaki; Satoh, Shinobu

    2014-11-01

    One week after partial incision of Arabidopsis inflorescence stems, the repair process in damaged tissue includes pith cell proliferation. Auxin is a key factor driving this process, and ANAC071, a transcription factor gene, is upregulated in the distal region of the incised stem. Here we show that XTH20 and the closely related XTH19, members of xyloglucan endotransglucosylase/hydrolases family catalyzing molecular grafting and/or hydrolysis of cell wall xyloglucans, were also upregulated in the distal part of the incised stem, similar to ANAC071. XTH19 was expressed in the proximal incision region after 3 days or after auxin application to the decapitated stem. Horizontal positioning of the plant with the incised side up resulted in decreased ProDR 5 :GUS, ANAC071, XTH20, and XTH19 expression and reduced pith cell proliferation. In incised stems of Pro35S :ANAC071-SRDX plants, expression of XTH20 and XTH19 was substantially and moderately decreased, respectively. XTH20 and XTH19 expression and pith cell proliferation were suppressed in anac071 plants and were increased in Pro35S :ANAC071 plants. Pith cell proliferation was also inhibited in the xth20xth19 double mutant. Furthermore, ANAC071 bound to the XTH20 and XTH19 promoters to induce their expression. This study revealed XTH20 and XTH19 induction by auxin via ANAC071 in the distal part of an incised stem and their involvement in cell proliferation in the tissue reunion process. © 2014 The Authors The Plant Journal © 2014 John Wiley & Sons Ltd.

  15. Residue-Specific α-Helix Propensities from Molecular Simulation

    PubMed Central

    Best, Robert B.; de Sancho, David; Mittal, Jeetain

    2012-01-01

    Formation of α-helices is a fundamental process in protein folding and assembly. By studying helix formation in molecular simulations of a series of alanine-based peptides, we obtain the temperature-dependent α-helix propensities of all 20 naturally occurring residues with two recent additive force fields, Amber ff03w and Amber ff99SB∗. Encouragingly, we find that the overall helix propensity of many residues is captured well by both energy functions, with Amber ff99SB∗ being more accurate. Nonetheless, there are some residues that deviate considerably from experiment, which can be attributed to two aspects of the energy function: i), variations of the charge model used to determine the atomic partial charges, with residues whose backbone charges differ most from alanine tending to have the largest error; ii), side-chain torsion potentials, as illustrated by the effect of modifications to the torsion angles of I, L, D, N. We find that constrained refitting of residue charges for charged residues in Amber ff99SB∗ significantly improves their helix propensity. The resulting parameters should more faithfully reproduce helix propensities in simulations of protein folding and disordered proteins. PMID:22455930

  16. Lifetime impact on residual stress of EUV pellicle

    NASA Astrophysics Data System (ADS)

    Kim, Min-Woo; Lee, Sung-Gyu; Park, Eun-Sang; Oh, Hye-Keun

    2017-10-01

    Since EUV pellicle is very thin, It can be affected easily on its manufacturing process or the exposure process. The Pellicle has several types of stress, above all the pellicle has a residual stress from its manufacturing process. To determine the effect of residual stress on the pellicle, we calculated residual stress of several types of multi-layer pellicle by using formula. We could confirm that the residual stress has non-negligible values through the calculation results, and we obtained the thermal stress of each pellicle by using finite element method (FEM). we optimized the pellicle through comparison of total stress by plus the calculated residual stress and the thermal stress. As a result, since the p-Si core pellicle with B4C capping satisfies both high transparent and low total stress, we chose p-Si core pellicle with B4C capping as a suitable pellicle.

  17. [Residual pleural thickening in tuberculous pleuritis. Associated factors

    PubMed

    Ruiz, E; Alegre, J; Alemán, C; Vizcaya, S; Armadans, L; Segura, R M; Andreu, J; Iglesias, D; Fernández de Sevilla, T

    2000-10-01

    To study the factors related to the development of residual pleural thickening in pleural tuberculosis. We studied 39 patients with tuberculous pleural effusion. A chest X-ray was taken of each patient at the end of treatment. The patients' medical histories, pleural fluid findings and diagnostic chest films were evaluated. Residual pleural thickening was defined as thickening that was visibly greater than 2 mm in the lower side portion of the chest film. Residual pleural thickening developed in 26% of patients and was found mainly in men (RR = 3.86). In no patients with Löwenstein-Jensen cultures positive for Mycobacterium tuberculosis did pleural complications develop. Residual pleural thickening is a common complication of tuberculous pleural effusion. Residual pleural thickening in tuberculous pleurisy occurs more often in men and older patients, and in cases in which pleural liquid culture is negative for M. tuberculosis.

  18. 40 CFR 180.371 - Thiophanate-methyl; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... residues. 180.371 Section 180.371 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.371 Thiophanate-methyl; tolerances for residues. (a) General. Tolerances are established for...

  19. Nanohardness and Residual Stress in TiN Coatings.

    PubMed

    Hernández, Luis Carlos; Ponce, Luis; Fundora, Abel; López, Enrique; Pérez, Eduardo

    2011-05-17

    TiN films were prepared by the Cathodic arc evaporation deposition method under different negative substrate bias. AFM image analyses show that the growth mode of biased coatings changes from 3D island to lateral when the negative bias potential is increased. Nanohardness of the thin films was measured by nanoindentation, and residual stress was determined using Grazing incidence X ray diffraction. The maximum value of residual stress is reached at -100 V substrate bias coinciding with the biggest values of adhesion and nanohardness. Nanoindentation measurement proves that the force-depth curve shifts due to residual stress. The experimental results demonstrate that nanohardness is seriously affected by the residual stress.

  20. Hair combing to collect organic gunshot residues (OGSR).

    PubMed

    MacCrehan, William A; Layman, Malinda J; Secl, Janelle D

    2003-08-12

    A protocol is presented for the collection and analysis of gunshot residues (GSR) from hair. A fine-toothed comb is used for collection of the residues. A small zip-closure bag serves as a container for both sample storage and extraction of the characteristic organic powder additives. The success of this residue recovery approach was tested on simulated shooters and victims using mannequin-supported human wig hair as well as on human shooters. Residues were collected from four weapons: a revolver and semi-automatic pistol, rifle and shotgun. One characteristic additive, nitroglycerin, was detected by capillary electrophoresis (CE) in the majority of the collection experiments.

  1. Hydrostatic weighing at residual volume and functional residual capacity.

    PubMed

    Thomas, T R; Etheridge, G L

    1980-07-01

    Hydrostatic weighing (HW) was performed at both residual volume (RV) and functional residual capacity (FRC) to determine if underwater weighing at different lung volumes affected the measurement of body density. Subjects were 43 males, 18-25 yr. Subjects were submerged in the prone position, and the lung volume was measured by helium dilution at the time of the underwater weighing. Underwater weight was first assessed at FRC followed by assessment at RV. Changes in lung volume were accurately reflected in the underwater weight. Body density (D) was not different with the use of the FRC (mean D = 1.0778) or RV (mean D = 1.0781) data. Percent fat values for the FRC and RV data were 9.3 +/- 5.4 and 9.2 +/- 5.1%, respectively, and were not statistically different. The results indicate that the difference between percent fat determinations by HW in the prone position at FRC and RV is negligible. Because measurement of underwater weight at FRC is more comfortable for the subject, this may be the method of choice when the lung volume can be measured during the underwater weighing.

  2. Organophosphorous residue in Liza aurata and Cyprinus carpio

    PubMed Central

    Shayeghi, Mansoreh; Khoobdel, Mehdi; Bagheri, Fatemeh; Abtahi, Mohammad; Zeraati, Hojjatollah

    2012-01-01

    Objective To determine the amount of azinphos methyl and diazinon residues in two river fishes, Liza aurata and Cyprinus carpio, in the north of Iran. Methods This study was done during 2006-2007. In this survey, 152 water and fish samples from Gorgan and Qarasu rivers, north of Iran, were investigated. Sampling was done in three predetermined stations along each river. Organophosphorus compounds (OPs) were extracted from the fishes and the water of rivers. After extraction, purification and concentration processes, the amount and type of insecticides in water and fish samples were determined by high performance thin layer chromatography (HPTLC). Results There was a significant difference in the residue of the insecticides in the water and fish samples between summer and other seasons in the two rivers. The highest amount of insecticides residue was seen during summer. In both rivers, the amount of diazinon and azinphos methyl residues in the two fishes was more than 2 000 mg/L in summer. There was no significant difference in insecticides residue between the fishes in two rivers. The diazinon residue was higher than the standard limits in both rivers during the spring and the summer, but the residual amount of azinphos methyl was higher than the standard limits only during the summer and only in Qarasu River. Conclusions It can be concluded that the amount of OPs in the water and the two fishes, Liza aurata and Cyprinus carpio, is higher than the permitted levels. PMID:23569972

  3. Residual Stress Analysis in Welded Component.

    NASA Astrophysics Data System (ADS)

    Rouhi, Shahab; Yoshida, Sanichiro; Miura, Fumiya; Sasaki, Tomohiro

    Due to local heating, thermal stresses occur during welding; and residual stress and distortion result remain welding. Welding distortion has negative effects on the accuracy of assembly, exterior appearance, and various strengths of the welded structures. Up to date, a lot of experiments and numerical analysis have been developed to assess residual stress. However, quantitative estimation of residual stress based on experiment may involve massive uncertainties and complexity of the measurement process. To comprehensively understand this phenomena, it is necessary to do further researches by means of both experiment and numerical simulation. In this research, we conduct Finite Element Analysis (FEA) for a simple butt-welded metal plate specimen. Thermal input and resultant expansion are modeled with a thermal expansion FEA module and the resultant constitutive response of the material is modeled with a continuous mechanic FEA module. The residual stress is modeled based on permanent deformation occurring during the heating phase of the material. Experiments have also been carried out to compare with the FEA results. Numerical and experimental results show qualitative agreement. The present work was supported by the Louisiana Board of Regents (LEQSF(2016-17)-RD-C-13).

  4. On the residual properties of damaged FRC

    NASA Astrophysics Data System (ADS)

    Zerbino, R.; Torrijos, M. C.; Giaccio, G.

    2017-09-01

    A discussion on the residual behaviour of Fibre Reinforced Concrete (FRC) is performed based on two selected cases of concrete degradation: the exposure at High Temperatures and the development of Alkali Silica Reactions. In addition, and taking in mind that the failure mechanism in FRC is strongly related with the fibre pull-out strength, the bond strength in damaged matrices was shown concluding that the residual bond strength is less affected than the matrix strength. As the damage increases, the compressive strength and the modulus of elasticity decrease, being the modulus of elasticity the most affected. There were no significant changes produced by the incorporation of fibres on the residual behaviour when compared with previous experience on plain damage concrete. Regarding the tensile behaviour although the first peak decreases as the damage increases, even for a severely damage FRC the residual stresses remain almost unaffected.

  5. Buried polar residues in coiled-coil interfaces.

    PubMed

    Akey, D L; Malashkevich, V N; Kim, P S

    2001-05-29

    Coiled coils, estimated to constitute 3-5% of the encoded residues in most genomes, are characterized by a heptad repeat, (abcdefg)(n), where the buried a and d positions form the interface between multiple alpha-helices. Although generally hydrophobic, a substantial fraction ( approximately 20%) of these a- and d-position residues are polar or charged. We constructed variants of the well-characterized coiled coil GCN4-p1 with a single polar residue (Asn, Gln, Ser, or Thr) at either an a or a d position. The stability and oligomeric specificity of each variant were measured, and crystal structures of coiled-coil trimers with threonine or serine at either an a or a d position were determined. The structures show how single polar residues in the interface affect not only local packing, but also overall coiled-coil geometry as seen by changes in the Crick supercoil parameters and core cavity volumes.

  6. 20 CFR 220.120 - The claimant's residual functional capacity.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 20 Employees' Benefits 1 2010-04-01 2010-04-01 false The claimant's residual functional capacity... RETIREMENT ACT DETERMINING DISABILITY Residual Functional Capacity § 220.120 The claimant's residual functional capacity. (a) General. The claimant's impairment(s), and any related symptoms, such as pain, may...

  7. Focus on agricultural residues: Microstructure of almond hull (abstract)

    USDA-ARS?s Scientific Manuscript database

    Agricultural residues have historically been used as animal feed or burned for disposal. These residues, therefore, have little economic value and may end up becoming disposal problems because tighter air quality control measures may limit burning of the residues. Therefore, value-added products mad...

  8. Residual Stress Analysis Based on Acoustic and Optical Methods.

    PubMed

    Yoshida, Sanichiro; Sasaki, Tomohiro; Usui, Masaru; Sakamoto, Shuichi; Gurney, David; Park, Ik-Keun

    2016-02-16

    Co-application of acoustoelasticity and optical interferometry to residual stress analysis is discussed. The underlying idea is to combine the advantages of both methods. Acoustoelasticity is capable of evaluating a residual stress absolutely but it is a single point measurement. Optical interferometry is able to measure deformation yielding two-dimensional, full-field data, but it is not suitable for absolute evaluation of residual stresses. By theoretically relating the deformation data to residual stresses, and calibrating it with absolute residual stress evaluated at a reference point, it is possible to measure residual stresses quantitatively, nondestructively and two-dimensionally. The feasibility of the idea has been tested with a butt-jointed dissimilar plate specimen. A steel plate 18.5 mm wide, 50 mm long and 3.37 mm thick is braze-jointed to a cemented carbide plate of the same dimension along the 18.5 mm-side. Acoustoelasticity evaluates the elastic modulus at reference points via acoustic velocity measurement. A tensile load is applied to the specimen at a constant pulling rate in a stress range substantially lower than the yield stress. Optical interferometry measures the resulting acceleration field. Based on the theory of harmonic oscillation, the acceleration field is correlated to compressive and tensile residual stresses qualitatively. The acoustic and optical results show reasonable agreement in the compressive and tensile residual stresses, indicating the feasibility of the idea.

  9. [Cognitive performance in schizophrenia (paranoid vs residual subtype)].

    PubMed

    Dillon, Carol; Taragano, Fernando; Sarasola, Diego; Iturry, Mónica; Serrano, Cecilia; Raczkowski, Amalia; Allegri, Ricardo

    2007-01-01

    Several studies refer to the relationship between schizophrenia and cognitive dysfunctions. The most frequent disturbances accepted are the deficits in the executive, memory and verbal tests. However, there are few comparative data about the cognitive functioning of the different subtypes of schizophrenia. Analyze and compare the neuropsychological disturbances present in patients with paranoid and residual schizophrenia. Eleven patients with paranoid schizophrenia, eleven patients with residual schizophrenia (DSM-IV criteria), and thirty one normal subjects matched by age, educational level, and general cognitive level (Mini Mental State Examination (Folstein, 1975), were assessed with a semistructured psychiatric examination and an extensive neuropsychological battery. Significant differences were found in memory, language, and executive functions when schizophrenics were compared with normal subjects. Differences in similarities were found between paranoid and residual schizophrenics. Residual schizophrenics had more disturbances in neuropsychological tests in comparison with paranoid schizophrenics. Schizophrenics demonstrated disturbances in memory, language, executive functions and attention. Residual schizophrenics had more impairment in neuropsychological tests than paranoid schizophrenics.

  10. Retrieving residue after overstory removal in true fir, northeastern California

    Treesearch

    Gary O. Fiddler; C. Phillip Weatherspoon

    1986-01-01

    Overstory removal cutting, the most common means of converting old-growth stands to young growth stands in California, can produce excessive residues that pose management problems. Utilization is an attractive option for managing residues. However, the cost of residue retrieval and utilization is often prohibitive. Residue retrieval by a private contractor was studied...

  11. [Drug residues in untreated swine].

    PubMed

    Kietzmann, M; Markus, W; Chavez, J; Bollwahn, W

    1995-11-01

    The concentration of sulfadimidine was measured in the urine of pigs which were housed (over five days) in boxes where other pigs have been treated orally with sulfadimidine before. Sulfadimidine was measured in the urine of the unmedicated pigs in a concentration of up to 4 micrograms/ml. Considering these urine concentrations, violative sulfadimidine tissue residues would be expectable in the carcass after slaughter. The practice of fixing withdrawal times must be considered again to ensure that drug residues in tissues are below the MRL before slaughter also in unmedicated animals.

  12. Low-residue and low-fiber diets in gastrointestinal disease management.

    PubMed

    Vanhauwaert, Erika; Matthys, Christophe; Verdonck, Lies; De Preter, Vicky

    2015-11-01

    Recently, low-residue diets were removed from the American Academy of Nutrition and Dietetics' Nutrition Care Manual due to the lack of a scientifically accepted quantitative definition and the unavailability of a method to estimate the amount of food residue produced. This narrative review focuses on defining the similarities and/or discrepancies between low-residue and low-fiber diets and on the diagnostic and therapeutic values of these diets in gastrointestinal disease management. Diagnostically, a low-fiber/low-residue diet is used in bowel preparation. A bowel preparation is a cleansing of the intestines of fecal matter and secretions conducted before a diagnostic procedure. Therapeutically, a low-fiber/low-residue diet is part of the treatment of acute relapses in different bowel diseases. The available evidence on low-residue and low-fiber diets is summarized. The main findings showed that within human disease research, the terms "low residue" and "low fiber" are used interchangeably, and information related to the quantity of residue in the diet usually refers to the amount of fiber. Low-fiber/low-residue diets are further explored in both diagnostic and therapeutic situations. On the basis of this literature review, the authors suggest redefining a low-residue diet as a low-fiber diet and to quantitatively define a low-fiber diet as a diet with a maximum of 10 g fiber/d. A low-fiber diet instead of a low-residue diet is recommended as a diagnostic value or as specific therapy for gastrointestinal conditions. © 2015 American Society for Nutrition.

  13. 40 CFR 180.644 - Cyprosulfamide; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... residues of the herbicide safener cyprosulfamide, N-[[4-[(cyclopropylamino)carbonyl] phenyl]sulfonyl]-2... (2) Tolerances are established for residues of the herbicide safener cyprosulfamide, N-[[4...

  14. 40 CFR 180.644 - Cyprosulfamide; tolerances for residues.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... residues of the herbicide safener cyprosulfamide, N-[[4-[(cyclopropylamino)carbonyl] phenyl]sulfonyl]-2... (2) Tolerances are established for residues of the herbicide safener cyprosulfamide, N-[[4...

  15. 40 CFR 180.644 - Cyprosulfamide; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... residues of the herbicide safener cyprosulfamide, N-[[4-[(cyclopropylamino)carbonyl] phenyl]sulfonyl]-2... (2) Tolerances are established for residues of the herbicide safener cyprosulfamide, N-[[4...

  16. 40 CFR 180.644 - Cyprosulfamide; tolerances for residues.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... residues of the herbicide safener cyprosulfamide, N-[[4-[(cyclopropylamino)carbonyl] phenyl]sulfonyl]-2... (2) Tolerances are established for residues of the herbicide safener cyprosulfamide, N-[[4...

  17. 40 CFR 180.644 - Cyprosulfamide; tolerances for residues.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... residues of the herbicide safener cyprosulfamide, N-[[4-[(cyclopropylamino)carbonyl] phenyl]sulfonyl]-2... (2) Tolerances are established for residues of the herbicide safener cyprosulfamide, N-[[4...

  18. 40 CFR 180.278 - Phenmedipham; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances... combined residues of the herbicide phenmedipham (3-methoxycarbonylaminophenyl-3′-methylcarbanilate) in or...

  19. 40 CFR 180.537 - Isoxaflutole; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances... combined residues of isoxaflutole 5-cyclopropyl-4-(2-methylsulfonyl-4-trifluoromethylbenzoyl) isoxazole and...

  20. 40 CFR 180.537 - Isoxaflutole; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances... combined residues of isoxaflutole 5-cyclopropyl-4-(2-methylsulfonyl-4-trifluoromethylbenzoyl) isoxazole and...

  1. 40 CFR 180.278 - Phenmedipham; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances... combined residues of the herbicide phenmedipham (3-methoxycarbonylaminophenyl-3′-methylcarbanilate) in or...

  2. 40 CFR 180.144 - Cyhexatin; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.144 Cyhexatin; tolerances for residues. (a) General. Tolerances are established for combined...

  3. 40 CFR 180.144 - Cyhexatin; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.144 Cyhexatin; tolerances for residues. (a) General. Tolerances are established for combined...

  4. Forest residues in hemlock-spruce forests of the Pacific Northwest and Alaska: a state-of-knowledge review with recommendations for residue management.

    Treesearch

    Robert H. Ruth; A.S. Harris

    1975-01-01

    The forest manager must balance all the interacting and often conflicting factors influencing residue management and decide on the best course of action. He needs to determine optimum volume, size, and arrangement of residues to leave on an area after logging, then to select the harvesting methods and residue management alternatives that best provide these conditions....

  5. Utilizing hardwood logging residue: a case study in the Appalachians

    Treesearch

    E. Paul Craft

    1976-01-01

    An Appalachian hardwood timber stand that contained 6,700 board feet per acre of sawtimber was harvested by clearcutting. After the merchantable sawlogs were removed, this stand contained 69.3 tons per acre of green wood residue. Thirty-three and one-third tons of residue were from tops of merchantable sawtimber; 36 tons were from residual trees. Treetop residue...

  6. RESIDUAL LIMB VOLUME CHANGE: SYSTEMATIC REVIEW OF MEASUREMENT AND MANAGEMENT

    PubMed Central

    Sanders, JE; Fatone, S

    2014-01-01

    Management of residual limb volume affects decisions regarding timing of fit of the first prosthesis, when a new prosthetic socket is needed, design of a prosthetic socket, and prescription of accommodation strategies for daily volume fluctuations. The purpose of this systematic review was to assess what is known about measurement and management of residual limb volume change in persons with lower-limb amputation. Publications that met inclusion criteria were grouped into three categories: (I) descriptions of residual limb volume measurement techniques; (II) studies on people with lower-limb amputation investigating the effect of residual limb volume change on clinical care; and (III) studies of residual limb volume management techniques or descriptions of techniques for accommodating or controlling residual limb volume. The review showed that many techniques for the measurement of residual limb volume have been described but clinical use is limited largely because current techniques lack adequate resolution and in-socket measurement capability. Overall, there is limited evidence regarding the management of residual limb volume, and the evidence available focuses primarily on adults with trans-tibial amputation in the early post-operative phase. While we can draw some insights from the available research about residual limb volume measurement and management, further research is required. PMID:22068373

  7. 40 CFR 180.441 - Quizalofop ethyl; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... combined residues of the herbicide quizalofop (2-[4-(6-chloroquinoxalin-2-yl oxy)phenoxy]propanoic acid... combined residues of the herbicide quizalofop (2-[4-(6-chloroquinoxalin-2-yl oxy)phenoxy]propanoic acid... byproducts 0.05 (3) Tolerances are established for the combined residues of the herbicide quizalofop-p ethyl...

  8. 40 CFR 180.430 - Fenoxaprop-ethyl; tolerances for residues.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... residues of the herbicide fenoxaprop-ethyl, including its metabolites and degradates, in or on the... for residues of the herbicide fenoxaprop-ethyl, including its metabolites and degradates, in or on the... registration, as defined in § 180.1(l), are established for residues of the herbicide fenoxaprop-ethyl...

  9. 40 CFR 180.441 - Quizalofop ethyl; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... combined residues of the herbicide quizalofop (2-[4-(6-chloroquinoxalin-2-yl oxy)phenoxy]propanoic acid... combined residues of the herbicide quizalofop (2-[4-(6-chloroquinoxalin-2-yl oxy)phenoxy]propanoic acid... byproducts 0.05 (3) Tolerances are established for the combined residues of the herbicide quizalofop-p ethyl...

  10. 40 CFR 180.231 - Dichlobenil; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.231 Dichlobenil; tolerances for residues. (a) General. Tolerances are established for the combined...

  11. 40 CFR 180.602 - Spiroxamine; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.602 Spiroxamine; tolerances for residues. (a) General. Tolerances are established for the combined...

  12. 40 CFR 180.407 - Thiodicarb; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.407 Thiodicarb; tolerances for residues. (a) General. Tolerances are established for the combined...

  13. 40 CFR 180.410 - Triadimefon; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.410 Triadimefon; tolerances for residues. (a) General. Tolerances are established for the combined...

  14. 40 CFR 180.604 - Mepanipyrim; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances...) Import tolerances. Tolerances are established for the combined residues of mepanipyrim, 4-methyl-N-phenyl...

  15. 40 CFR 180.231 - Dichlobenil; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.231 Dichlobenil; tolerances for residues. (a) General. Tolerances are established for the combined...

  16. 40 CFR 180.596 - Fosthiazate; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.596 Fosthiazate; tolerances for residues. (a) General. Tolerances are established for the combined...

  17. 40 CFR 180.604 - Mepanipyrim; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances...) Import tolerances. Tolerances are established for the combined residues of mepanipyrim, 4-methyl-N-phenyl...

  18. Quantification of residual EDU (N-ethyl-N'-(dimethylaminopropyl) carbodiimide (EDC) hydrolyzed urea derivative) and other residual by LC-MS/MS.

    PubMed

    Lei, Q Paula; Lamb, David H; Shannon, Anthony G; Cai, Xinxing; Heller, Ronald K; Huang, Michael; Zablackis, Earl; Ryall, Robert; Cash, Patricia

    2004-12-25

    An LC-MS/MS method for determination of the break down product of N-ethyl-N'-(3-dimethylaminopropyl) carbodiimide (EDC) urea derivative, EDU, has been developed and validated for monitoring the residual coupling reagents. Results indicate that the method exhibits suitable specificity, sensitivity, precision, linearity and accuracy for quantification of residual EDU in the presence of meningococcal polysaccharide-diphtheria toxoid conjugate vaccine and other vaccine matrix compounds. The assay has been validated for a detection range of 10-100 ng/mL and then successfully transferred to quality control (QC) lab. This same method has also been applied to the determination of residual diaminohexane (DAH) in the presence of EDU. LC-MS/MS has proven to be useful as a quick and sensitive approach for simultaneous determination of multiple residual compounds in glycoconjugate vaccine samples.

  19. Conversion of direct process high-boiling residue to monosilanes

    DOEpatents

    Brinson, Jonathan Ashley; Crum, Bruce Robert; Jarvis, Jr., Robert Frank

    2000-01-01

    A process for the production of monosilanes from the high-boiling residue resulting from the reaction of hydrogen chloride with silicon metalloid in a process typically referred to as the "direct process." The process comprises contacting a high-boiling residue resulting from the reaction of hydrogen chloride and silicon metalloid, with hydrogen gas in the presence of a catalytic amount of aluminum trichloride effective in promoting conversion of the high-boiling residue to monosilanes. The present process results in conversion of the high-boiling residue to monosilanes. At least a portion of the aluminum trichloride catalyst required for conduct of the process may be formed in situ during conduct of the direct process and isolation of the high-boiling residue.

  20. Sequence composition and environment effects on residue fluctuations in protein structures

    NASA Astrophysics Data System (ADS)

    Ruvinsky, Anatoly M.; Vakser, Ilya A.

    2010-10-01

    Structure fluctuations in proteins affect a broad range of cell phenomena, including stability of proteins and their fragments, allosteric transitions, and energy transfer. This study presents a statistical-thermodynamic analysis of relationship between the sequence composition and the distribution of residue fluctuations in protein-protein complexes. A one-node-per-residue elastic network model accounting for the nonhomogeneous protein mass distribution and the interatomic interactions through the renormalized inter-residue potential is developed. Two factors, a protein mass distribution and a residue environment, were found to determine the scale of residue fluctuations. Surface residues undergo larger fluctuations than core residues in agreement with experimental observations. Ranking residues over the normalized scale of fluctuations yields a distinct classification of amino acids into three groups: (i) highly fluctuating-Gly, Ala, Ser, Pro, and Asp, (ii) moderately fluctuating-Thr, Asn, Gln, Lys, Glu, Arg, Val, and Cys, and (iii) weakly fluctuating-Ile, Leu, Met, Phe, Tyr, Trp, and His. The structural instability in proteins possibly relates to the high content of the highly fluctuating residues and a deficiency of the weakly fluctuating residues in irregular secondary structure elements (loops), chameleon sequences, and disordered proteins. Strong correlation between residue fluctuations and the sequence composition of protein loops supports this hypothesis. Comparing fluctuations of binding site residues (interface residues) with other surface residues shows that, on average, the interface is more rigid than the rest of the protein surface and Gly, Ala, Ser, Cys, Leu, and Trp have a propensity to form more stable docking patches on the interface. The findings have broad implications for understanding mechanisms of protein association and stability of protein structures.

  1. 40 CFR 180.181 - Chlorpropham; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... residues of the plant regulator and herbicide chlorpropham (isopropyl m-chlorocarbanilate (CIPC) in or on...) Tolerances are established for the combined residues of the plant regulator and herbicide chlorpropham...

  2. 40 CFR 180.181 - Chlorpropham; tolerances for residues.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... residues of the plant regulator and herbicide chlorpropham (isopropyl m-chlorocarbanilate (CIPC) in or on...) Tolerances are established for the combined residues of the plant regulator and herbicide chlorpropham...

  3. 40 CFR 180.181 - Chlorpropham; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... residues of the plant regulator and herbicide chlorpropham (isopropyl m-chlorocarbanilate (CIPC) in or on...) Tolerances are established for the combined residues of the plant regulator and herbicide chlorpropham...

  4. 40 CFR 180.181 - Chlorpropham; tolerances for residues.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... residues of the plant regulator and herbicide chlorpropham (isopropyl m-chlorocarbanilate (CIPC) in or on...) Tolerances are established for the combined residues of the plant regulator and herbicide chlorpropham...

  5. 40 CFR 180.181 - Chlorpropham; tolerances for residues.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... residues of the plant regulator and herbicide chlorpropham (isopropyl m-chlorocarbanilate (CIPC) in or on...) Tolerances are established for the combined residues of the plant regulator and herbicide chlorpropham...

  6. Fluorescence of crop residue: postmortem analysis of crop conditions

    NASA Astrophysics Data System (ADS)

    McMurtrey, James E., III; Kim, Moon S.; Daughtry, Craig S. T.; Corp, Lawrence A.; Chappelle, Emmett W.

    1997-07-01

    Fluorescence of crop residues at the end of the growing season may provide an indicator of the past crop's vegetative condition. Different levels of nitrogen (N) fertilization were applied to field grown corn and wheat at Beltsville, Maryland. The N fertilizer treatments produce a range of physiological conditions, pigment concentrations, biomass levels, and grain yields that resulted in varying growth and stress conditions in the living crops. After normal harvesting procedures the crop residues remained. The fluorescence spectral characteristics of the plant residues from crops grown under different levels of N nutrition were analyzed. The blue-green fluorescence response of in-vitro residue biomass of the N treated field corn had different magnitudes. A blue-green- yellow algorithm, (460/525)*600 nm, gave the best separations between prior corn growth conditions at different N fertilization levels. Relationships between total dry biomass, the grain yield, and fluorescence properties in the 400 - 670 nm region of the spectrum were found in both corn and wheat residues. The wheat residue was analyzed to evaluate the constituents responsible for fluorescence. A ratio of the blue-green, 450/550 nm, images gave the best separation among wheat residues at different N fertilization levels. Fluorescence of extracts from wheat residues showed inverse fluorescence intensities as a function of N treatments compared to that of the intact wheat residue or ground residue samples. The extracts also had an additional fluorescence emission peak in the red, 670 nm. Single band fluorescence intensity in corn and wheat residues is due mostly to the quantity of the material on the soil surface. Ratios of fluorescence bands varied as a result of the growth conditions created by the N treatments and are thought to be indicative of the varying concentrations of the plant residues fluorescing constituents. Estimates of the amount and cost effectiveness of N fertilizers to satisfy

  7. Residuals Management and Water Pollution Control Planning.

    ERIC Educational Resources Information Center

    Environmental Protection Agency, Washington, DC. Office of Public Affairs.

    This pamphlet addresses the problems associated with residuals and water quality especially as it relates to the National Water Pollution Control Program. The types of residuals and appropriate management systems are discussed. Additionally, one section is devoted to the role of citizen participation in developing management programs. (CS)

  8. Objective identification of residue ranges for the superposition of protein structures

    PubMed Central

    2011-01-01

    Background The automation of objectively selecting amino acid residue ranges for structure superpositions is important for meaningful and consistent protein structure analyses. So far there is no widely-used standard for choosing these residue ranges for experimentally determined protein structures, where the manual selection of residue ranges or the use of suboptimal criteria remain commonplace. Results We present an automated and objective method for finding amino acid residue ranges for the superposition and analysis of protein structures, in particular for structure bundles resulting from NMR structure calculations. The method is implemented in an algorithm, CYRANGE, that yields, without protein-specific parameter adjustment, appropriate residue ranges in most commonly occurring situations, including low-precision structure bundles, multi-domain proteins, symmetric multimers, and protein complexes. Residue ranges are chosen to comprise as many residues of a protein domain that increasing their number would lead to a steep rise in the RMSD value. Residue ranges are determined by first clustering residues into domains based on the distance variance matrix, and then refining for each domain the initial choice of residues by excluding residues one by one until the relative decrease of the RMSD value becomes insignificant. A penalty for the opening of gaps favours contiguous residue ranges in order to obtain a result that is as simple as possible, but not simpler. Results are given for a set of 37 proteins and compared with those of commonly used protein structure validation packages. We also provide residue ranges for 6351 NMR structures in the Protein Data Bank. Conclusions The CYRANGE method is capable of automatically determining residue ranges for the superposition of protein structure bundles for a large variety of protein structures. The method correctly identifies ordered regions. Global structure superpositions based on the CYRANGE residue ranges allow a

  9. 40 CFR 180.659 - Pyroxasulfone; tolerances for residues.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... residues of the herbicide pyroxasulfone, including its metabolites and degradates, in or on the commodities... established for residues of the herbicide pyroxasulfone, including its metabolites and degradates, in or on...

  10. 40 CFR 180.648 - Meptyldinocap; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances... combined residues of the fungicide meptyldinocap, 2-(1-methylheptyl)-4,6-dinitrophenyl (2E)-2-butenoate and...

  11. 40 CFR 180.648 - Meptyldinocap; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances... combined residues of the fungicide meptyldinocap, 2-(1-methylheptyl)-4,6-dinitrophenyl (2E)-2-butenoate and...

  12. Microtox(TM) characterization of foundry sand residuals

    USGS Publications Warehouse

    Bastian, K.C.; Alleman, J.E.

    1998-01-01

    Although foundry residuals, consisting mostly of waste Sands, represent a potentially attractive, high-volume resource for beneficial reuse applications (e.g. highway embankment construction), prospective end users are understandably concerned about unforeseen liabilities stemming from the use of these residuals. This paper, therefore, focuses on the innovative use of a microbial bioassay as a means of developing a characterization of environmental suitability extending beyond the analytical coverage already provided by mandated chemical-specific tests (i.e., TCLP, etc.). Microtox(TM) bioassays were conducted on leachates derived from residuals obtained at a wide range of facilities, including: 11 gray and ductile iron foundries plus one each steel and aluminum foundries. In addition, virgin sand samples were used to establish a relative 'natural' benchmark against which the waste foundry sands could then be compared in terms of their apparent quality. These bioassay tests were able to effectively 'fingerprint' those residuals whose bioassay behavior was comparable to that of virgin materials. In fact, the majority of gray and ductile iron foundry residuals tested during this reported study elicited Microtox(TM) response levels which fell within or below the virgin sand response range, consequently providing another quantifiable layer of Support for this industry's claim that their sands are 'cleaner than dirt.' However, negative Microtox(TM) responses beyond that of the virgin sands were observed with a number of foundry samples (i.e. four of the 11 gray or ductile iron sands plus both non-iron sands). Therefore, the latter results would suggest that these latter residuals be excluded from beneficial reuse for the immediate future, at least until the cause and nature of this negative response has been further identified.

  13. Logging residue in Washington, Oregon, California: volume and characteristics.

    Treesearch

    James O. Howard

    1973-01-01

    This report makes available data on the volume and characteristics of logging residue resulting from 1969 logging operations in Oregon, Washington, and California. The results indicate highest volumes of logging residue are found in the Douglas-fir region of western Oregon and western Washington. Average gross volume of residue in this region ranged...

  14. Characterization of liquefied wood residues from different liquefaction conditions

    Treesearch

    Hui Pan; Todd f. Shupe; Chung-Yun Hse

    2007-01-01

    The amount of wood residue is used as a measurement of the extent of wood liquefaction. Characterization of the residue from wood liquefaction provides a new approach to understand some fundamental aspects of the liquefaction reaction. Residues were characterized by wet chemical analyses, Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), and...

  15. Bacterial amelioration of bauxite residue waste of industrial alumina plants.

    PubMed

    Hamdy, M K; Williams, F S

    2001-10-01

    The high alkali content of bauxite residue deposits from alumina production plants in industrial nations poses a challenge to reestablish flora and fauna at the deposit sites. The present study demonstrated that low levels of injured bacterial cells in the bauxite residue actively grew using various added nutrients and/or hay. The organisms grew from less than 10 to more than 10(9) cells g(-1) bauxite residue and formed organic acids that lowered the pH from 13 to about 7.0. A total of 150 cultures was isolated from treated bauxite residue and included species of Bacillus, Lactobacillus, Leuconostoc, Micrococcus, Staphylococcus, Pseudomonas, Flavobacterium and Enterobacter. Scanning electron micrographs demonstrated that untreated particles (control) of the bauxite residue were clumped together, and in treated bauxite residue these particles were highly dispersed with microcolonial structures. Furthermore, the treated bauxite residue supported growth of several plants and earthworms that survived for over 300 days. In a test plot bioremediation on a residue deposit at Alcoa Point Comfort, TX, the Bermuda grass hay used was effective mulch material and encouraged water filtration, leading to establishment and growth of salt-tolerant vegetative species.

  16. Tweaked residual convolutional network for face alignment

    NASA Astrophysics Data System (ADS)

    Du, Wenchao; Li, Ke; Zhao, Qijun; Zhang, Yi; Chen, Hu

    2017-08-01

    We propose a novel Tweaked Residual Convolutional Network approach for face alignment with two-level convolutional networks architecture. Specifically, the first-level Tweaked Convolutional Network (TCN) module predicts the landmark quickly but accurately enough as a preliminary, by taking low-resolution version of the detected face holistically as the input. The following Residual Convolutional Networks (RCN) module progressively refines the landmark by taking as input the local patch extracted around the predicted landmark, particularly, which allows the Convolutional Neural Network (CNN) to extract local shape-indexed features to fine tune landmark position. Extensive evaluations show that the proposed Tweaked Residual Convolutional Network approach outperforms existing methods.

  17. Longitudinal residual stresses in boron fibers

    NASA Technical Reports Server (NTRS)

    Behrendt, D. R.

    1976-01-01

    A method of measuring the longitudinal residual stress distribution in boron fibers is presented. The residual stresses in commercial CVD boron on tungsten fibers of 102, 142, and 203 microns (4, 5.6, and 8 mil) diameters were determined. Results for the three sizes show a compressive stress at the surface 800 to -1400 MN/sq m 120 to -200 ksi), changing monotonically to a region of tensile stress within the boron. At approximately 25 percent of the original radius, the stress reaches a maximum tensile 600 to 1000 MN/sq m(90 to 150 ksi) and then decreases to compressive near the tungsten boride core. The core itself is under a compressive stress of approximately -1300 MN/sq m (-190 ksi). The effects of surface removal on core residual stress and core-initiated fracture are discussed.

  18. Peptides containing internal residues of pyroglutamic acid: proton NMR characteristics

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Khan, S.A.

    1986-05-01

    The proton NMR characteristics of internal pyroglutamic acid (Glp; 5-oxoproline) residues in seven tripeptides of the general structure Boc-Xxx-Glp-Yyy-NH/sub 2/ were studied. In general, the chemical shifts of several diagnostic protons moved downfield on going from the Glu-containing peptides (Boc-Xxx-Glu-Yyy-NH/sub 2/) to the corresponding Glp-containing peptides. The C-2 proton of the Xxx residue was shifted by about 1.1 ppm. The N-2 proton of the Yyy residue was shifted by about 0.5 ppm. The C-2 proton of the Glx residue itself was shifted by about 0.5 ppm. One of the Glx C-3 protons was also shifted by about 0.5 ppm, butmore » the other remained essentially unchanged. Finally, the Glx C-4 protons were shifted by about 0.3 ppm. Internal Glu residues are readily converted chemically into internal Glp residues. This conversion also occurs as a side reaction during HP cleavage of the protecting group from Glu(OBzl) residues. The spontaneous fragmentation of serum proteins C3, C4 and lambda/sub 2/-macroglobulin under denaturing conditions is probably due to regioselective hydrolysis of an internal Glp residue formed in each of these proteins upon denaturation. These proton NMR characteristics may be useful in establishing the presence of internal Glp residues in synthetic and natural peptides.« less

  19. Developing with Residual Practice in EFL Classrooms

    ERIC Educational Resources Information Center

    Kivanç Çaganaga, Çagda; Kaymakamoglu, Sibel

    2015-01-01

    This article explores the concept of residual practice as a means of understanding the importance of daily experience on classroom management. The suggested theory can adequately illuminate the nature and process of learning while teaching in classrooms. This article aims to provide residual practice as a comprehensive framework for evaluating the…

  20. 9 CFR 381.80 - General; biological residues.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false General; biological residues. 381.80 Section 381.80 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE... Carcasses and Parts § 381.80 General; biological residues. (a) The carcasses or parts of carcasses of all...

  1. Distribution of veterinary drug residues among muscles

    USDA-ARS?s Scientific Manuscript database

    The U.S. Food and Drug Administration sets tolerances for veterinary drug residues in muscle, but does not specify which muscle should be sampled for analysis. The goal of this research was to determine if antibiotic residue levels are dependent on muscle type. In this study, penicillin G (Pen G) d...

  2. 40 CFR 180.610 - Aminopyralid; tolerances for residues.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... residues of the herbicide aminopyralid, 4-amino-3,6-dichloro-2-pyridinecarboxylic acid, including its... 4.0 Wheat, straw 0.25 (2) Tolerances are established for residues of the herbicide aminopyralid, 4...

  3. 40 CFR 180.610 - Aminopyralid; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... residues of the herbicide aminopyralid, 4-amino-3,6-dichloro-2-pyridinecarboxylic acid, including its... 4.0 Wheat, straw 0.25 (2) Tolerances are established for residues of the herbicide aminopyralid, 4...

  4. 40 CFR 180.610 - Aminopyralid; tolerances for residues.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... residues of the herbicide aminopyralid, 4-amino-3,6-dichloro-2-pyridinecarboxylic acid, including its... 4.0 Wheat, straw 0.25 (2) Tolerances are established for residues of the herbicide aminopyralid, 4...

  5. 40 CFR 180.610 - Aminopyralid; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... residues of the herbicide aminopyralid, 4-amino-3,6-dichloro-2-pyridinecarboxylic acid, including its... 4.0 Wheat, straw 0.25 (2) Tolerances are established for residues of the herbicide aminopyralid, 4...

  6. 40 CFR 180.610 - Aminopyralid; tolerances for residues.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... residues of the herbicide aminopyralid, 4-amino-3,6-dichloro-2-pyridinecarboxylic acid, including its... 4.0 Wheat, straw 0.25 (2) Tolerances are established for residues of the herbicide aminopyralid, 4...

  7. 40 CFR 180.536 - Triazamate; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances... the combined residues of triazamate (RH-7988) ethyl(3-tert-butyl-1-dimethylcarbamoyl-1H-1,2,4-triazol...

  8. 40 CFR 180.536 - Triazamate; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances... the combined residues of triazamate (RH-7988) ethyl(3-tert-butyl-1-dimethylcarbamoyl-1H-1,2,4-triazol...

  9. Roles of histidine residues in plant vacuolar H(+)-pyrophosphatase.

    PubMed

    Hsiao, Yi Y; Van, Ru C; Hung, Shu H; Lin, Hsin H; Pan, Rong L

    2004-02-15

    Vacuolar proton pumping pyrophosphatase (H(+)-PPase; EC 3.6.1.1) plays a pivotal role in electrogenic translocation of protons from cytosol to the vacuolar lumen at the expense of PP(i) hydrolysis. Alignment analysis on amino acid sequence demonstrates that vacuolar H(+)-PPase of mung bean contains six highly conserved histidine residues. Previous evidence indicated possible involvement of histidine residue(s) in enzymatic activity and H(+)-translocation of vacuolar H(+)-PPase as determined by using histidine specific modifier, diethylpyrocarbonate [J. Protein Chem. 21 (2002) 51]. In this study, we further attempted to identify the roles of histidine residues in mung bean vacuolar H(+)-PPase by site-directed mutagenesis. A line of mutants with histidine residues singly replaced by alanine was constructed, over-expressed in Saccharomyces cerevisiae, and then used to determine their enzymatic activities and proton translocations. Among the mutants scrutinized, only the mutation of H716 significantly decreased the enzymatic activity, the proton transport, and the coupling ratio of vacuolar H(+)-PPase. The enzymatic activity of H716A is relatively resistant to inhibition by diethylpyrocarbonate as compared to wild-type and other mutants, indicating that H716 is probably the target residue for the attack by this modifier. The mutation at H716 of V-PPase shifted the optimum pH value but not the T(1/2) (pretreatment temperature at which half enzymatic activity is observed) for PP(i) hydrolytic activity. Mutation of histidine residues obviously induced conformational changes of vacuolar H(+)-PPase as determined by immunoblotting analysis after limited trypsin digestion. Furthermore, mutation of these histidine residues modified the inhibitory effects of F(-) and Na(+), but not that of Ca(2+). Single substitution of H704, H716 and H758 by alanine partially released the effect of K(+) stimulation, indicating possible location of K(+) binding in the vicinity of domains

  10. 21 CFR 500.86 - Marker residue and target tissue.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Marker residue and target tissue. 500.86 Section...-Producing Animals § 500.86 Marker residue and target tissue. (a) For each edible tissue, the sponsor shall...) From these data, FDA will select a target tissue and a marker residue and designate the concentration...

  11. 21 CFR 500.86 - Marker residue and target tissue.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 6 2011-04-01 2011-04-01 false Marker residue and target tissue. 500.86 Section...-Producing Animals § 500.86 Marker residue and target tissue. (a) For each edible tissue, the sponsor shall...) From these data, FDA will select a target tissue and a marker residue and designate the concentration...

  12. Statistical Techniques to Analyze Pesticide Data Program Food Residue Observations.

    PubMed

    Szarka, Arpad Z; Hayworth, Carol G; Ramanarayanan, Tharacad S; Joseph, Robert S I

    2018-06-26

    The U.S. EPA conducts dietary-risk assessments to ensure that levels of pesticides on food in the U.S. food supply are safe. Often these assessments utilize conservative residue estimates, maximum residue levels (MRLs), and a high-end estimate derived from registrant-generated field-trial data sets. A more realistic estimate of consumers' pesticide exposure from food may be obtained by utilizing residues from food-monitoring programs, such as the Pesticide Data Program (PDP) of the U.S. Department of Agriculture. A substantial portion of food-residue concentrations in PDP monitoring programs are below the limits of detection (left-censored), which makes the comparison of regulatory-field-trial and PDP residue levels difficult. In this paper, we present a novel adaption of established statistical techniques, the Kaplan-Meier estimator (K-M), the robust regression on ordered statistic (ROS), and the maximum-likelihood estimator (MLE), to quantify the pesticide-residue concentrations in the presence of heavily censored data sets. The examined statistical approaches include the most commonly used parametric and nonparametric methods for handling left-censored data that have been used in the fields of medical and environmental sciences. This work presents a case study in which data of thiamethoxam residue on bell pepper generated from registrant field trials were compared with PDP-monitoring residue values. The results from the statistical techniques were evaluated and compared with commonly used simple substitution methods for the determination of summary statistics. It was found that the maximum-likelihood estimator (MLE) is the most appropriate statistical method to analyze this residue data set. Using the MLE technique, the data analyses showed that the median and mean PDP bell pepper residue levels were approximately 19 and 7 times lower, respectively, than the corresponding statistics of the field-trial residues.

  13. DNA quantification of basidiomycetous fungi during storage of logging residues

    PubMed Central

    Alfredsen, Gry; Filbakk, Tore; Fossdal, Carl Gunnar

    2015-01-01

    The demand for bioenergy caused an increased use of logging residues, branches and treetops that were previously left on the ground after harvesting. Residues are stored outdoors in piles and it is unclear to what extent fungi transform this material. Our objective was to quantify the amount of wood degrading fungi during storage using quantitative real-time PCR (qPCR) to detect basidiomycetous DNA in logging residues, a novel approach in this field. We found that the qPCR method was accurate in quantifying the fungal DNA during storage. As the moisture content of the piled logging residues decreased during the storage period, the fungal DNA content also decreased. Scots pine residues contained more fungal DNA than residues from Norway spruce. Loose piles had generally more fungal DNA than bundled ones. PMID:25870777

  14. Residual stress in glass: indentation crack and fractography approaches.

    PubMed

    Anunmana, Chuchai; Anusavice, Kenneth J; Mecholsky, John J

    2009-11-01

    To test the hypothesis that the indentation crack technique can determine surface residual stresses that are not statistically significantly different from those determined from the analytical procedure using surface cracks, the four-point flexure test, and fracture surface analysis. Soda-lime-silica glass bar specimens (4 mm x 2.3 mm x 28 mm) were prepared and annealed at 650 degrees C for 30 min before testing. The fracture toughness values of the glass bars were determined from 12 specimens based on induced surface cracks, four-point flexure, and fractographic analysis. To determine the residual stress from the indentation technique, 18 specimens were indented under 19.6N load using a Vickers microhardness indenter. Crack lengths were measured within 1 min and 24h after indentation, and the measured crack lengths were compared with the mean crack lengths of annealed specimens. Residual stress was calculated from an equation developed for the indentation technique. All specimens were fractured in a four-point flexure fixture and the residual stress was calculated from the strength and measured crack sizes on the fracture surfaces. The results show that there was no significant difference between the residual stresses calculated from the two techniques. However, the differences in mean residual stresses calculated within 1 min compared with those calculated after 24h were statistically significant (p=0.003). This study compared the indentation technique with the fractographic analysis method for determining the residual stress in the surface of soda-lime-silica glass. The indentation method may be useful for estimating residual stress in glass.

  15. THE IMMIGRANT POOR AND THE RESIDUAL POOR.

    ERIC Educational Resources Information Center

    SEGALMAN, RALPH

    AN ANALYSIS OF THE LIVES OF THE POOR IN AMERICA WILL SHOW DIFFERENCES BETWEEN THE IMMIGRANT (AND REFUGEE) POOR AND THE RESIDUAL POOR (NEGROES, PUERTO RICANS, LATIN AMERICANS, INDIANS, AND OTHERS). THE IMMIGRANT POOR WERE ACCULTURATED AND ABSORBED INTO THE MAINSTREAM OF AMERICAN LIFE WITHIN THREE GENERATIONS, WHEREAS THE RESIDUAL POOR HAVE BEEN…

  16. Investigating Resulting Residual Stresses during Mechanical Forming Process

    NASA Astrophysics Data System (ADS)

    Akinlabi, Stephen A.; Fatoba, Olawale S.; Mashinini, Peter M.; Akinlabi, Esther T.

    2018-03-01

    Most manufacturing processes such as machining, welding, heat treatment, laser forming, laser cladding and, laser metal deposition, etc. are subjected to a form of heat or energy to change the geometrical shape thus changing the inherent engineering and structural properties of the material. These changes often cause the development of locked up stresses referred to as residual stresses as a result of these activities. This study reports on the residual stresses developed due to the mechanical forming process to maintain a suitable structural integrity for the formed components. The result of the analysis through the X-ray diffraction confirmed that residual stresses were induced in the manufactured parts and further revealed that residual stresses were compressive in nature as found in the parent material but with values less than the parent material.

  17. Minimized-Laplacian residual interpolation for color image demosaicking

    NASA Astrophysics Data System (ADS)

    Kiku, Daisuke; Monno, Yusuke; Tanaka, Masayuki; Okutomi, Masatoshi

    2014-03-01

    A color difference interpolation technique is widely used for color image demosaicking. In this paper, we propose a minimized-laplacian residual interpolation (MLRI) as an alternative to the color difference interpolation, where the residuals are differences between observed and tentatively estimated pixel values. In the MLRI, we estimate the tentative pixel values by minimizing the Laplacian energies of the residuals. This residual image transfor- mation allows us to interpolate more easily than the standard color difference transformation. We incorporate the proposed MLRI into the gradient based threshold free (GBTF) algorithm, which is one of current state-of- the-art demosaicking algorithms. Experimental results demonstrate that our proposed demosaicking algorithm can outperform the state-of-the-art algorithms for the 30 images of the IMAX and the Kodak datasets.

  18. Acephate and buprofezin residues in olives and olive oil.

    PubMed

    Cabras, P; Angioni, A; Garau, V L; Pirisi, F M; Cabitza, F; Pala, M

    2000-10-01

    Field trials were carried out to study the persistence of acephate and buprofezin on olives. Two cultivars, pizz'e carroga and pendolino, with very large and small fruits respectively were used. After treatment, no difference was found between the two pesticide deposits on the olives. The disappearance rates, calculated as pseudo first order kinetics, were similar for both pesticides (on average 12 days). Methamidophos, the acephate metabolite, was always present on all olives, and in some pendolino samples it showed higher residues than the maximum residue limit (MRL). During washing, the first step of olive processing, the residue level of both pesticides on the olives did not decrease. After processing of the olives into oil, no residues of acephate or methamidophos were found in the olive oil, while the residues of buprofezin were on average four times higher than on olives.

  19. 40 CFR 180.569 - Forchlorfenuron; tolerances for residues.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... residues of the plant growth regulator forchlorfenuron; N-(2-chloro-4-pyridinyl)-N′phenyl urea in or on the....06 Kiwifruit 0.04 (2) Time-limited tolerances are established for residues of the plant growth...

  20. 40 CFR 180.569 - Forchlorfenuron; tolerances for residues.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... residues of the plant growth regulator forchlorfenuron; N-(2-chloro-4-pyridinyl)-N′phenyl urea in or on the....06 Kiwifruit 0.04 (2) Time-limited tolerances are established for residues of the plant growth...

  1. 40 CFR 180.569 - Forchlorfenuron; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... residues of the plant growth regulator forchlorfenuron; N-(2-chloro-4-pyridinyl)-N′phenyl urea in or on the....06 Kiwifruit 0.04 (2) Time-limited tolerances are established for residues of the plant growth...

  2. 40 CFR 180.569 - Forchlorfenuron; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... residues of the plant growth regulator forchlorfenuron; N-(2-chloro-4-pyridinyl)-N′phenyl urea in or on the....06 Kiwifruit 0.04 (2) Time-limited tolerances are established for residues of the plant growth...

  3. Helicoverpa zea (Lepidoptera: Noctuidae) and Spodoptera frugiperda (Lepidoptera: Noctuidae) Responses to Sorghum bicolor (Poales: Poaceae) Tissues From Lowered Lignin Lines

    PubMed Central

    Dowd, Patrick F.; Sattler, Scott E.

    2015-01-01

    The presence of lignin within biomass impedes the production of liquid fuels. Plants with altered lignin content and composition are more amenable to lignocellulosic conversion to ethanol and other biofuels but may be more susceptible to insect damage where lignin is an important resistance factor. However, reduced lignin lines of switchgrasses still retained insect resistance in prior studies. Therefore, we hypothesized that sorghum lines with lowered lignin content will also retain insect resistance. Sorghum excised leaves and stalk pith Sorghum bicolor (L.) Moench (Poales: Poaceae) from near isogenic brown midrib (bmr) 6 and 12 mutants lines, which have lowered lignin content and increased lignocellulosic ethanol conversion efficiency, were examined for insect resistance relative to wild-type (normal BTx623). Greenhouse and growth chamber grown plant tissues were fed to first-instar larvae of corn earworms, Helicoverpa zea (Boddie) and fall armyworms Spodoptera frugiperda (J.E. Smith) (Lepidoptera: Noctuidae), two sorghum major pests. Younger bmr leaves had significantly greater feeding damage in some assays than wild-type leaves, but older bmr6 leaves generally had significantly less damage than wild-type leaves. Caterpillars feeding on the bmr6 leaves often weighed significantly less than those feeding on wild-type leaves, especially in the S. frugiperda assays. Larvae fed the pith from bmr stalks had significantly higher mortality compared with those larvae fed on wild-type pith, which suggested that bmr pith was more toxic. Thus, reducing lignin content or changing subunit composition of bioenergy grasses does not necessarily increase their susceptibility to insects and may result in increased resistance, which would contribute to sustainable production. PMID:25601946

  4. Importance of residual primary cancer after induction therapy for esophageal adenocarcinoma.

    PubMed

    Raja, Siva; Rice, Thomas W; Ehrlinger, John; Goldblum, John R; Rybicki, Lisa A; Murthy, Sudish C; Adelstein, David; Videtic, Gregory; McNamara, Michael P; Blackstone, Eugene H

    2016-09-01

    To (1) assess the continuous distribution of the percentage of residual primary cancer in resection specimens after induction therapy for locally advanced esophageal adenocarcinoma, (2) determine the effects of residual primary cancer on survival after esophagectomy, (3) ascertain interplay between residual primary cancer and classical classifications of response to induction therapy (ypTNM), and (4) identify predictors of residual primary cancer. From January 2006 to November 2012, 188 patients (78%) underwent accelerated chemoradiotherapy, and 52 patients (22%) underwent chemotherapy alone followed by esophagectomy for adenocarcinoma. Mean age was 61 ± 9.2 years, and 89% were male. Residual primary cancer, assessed as the percentage of residual primary cancer cells in resection specimens, was quantified histologically by a gastrointestinal pathologist. Random Forest technology was used for data analysis. Twenty-five specimens (10%) had no residual primary cancer (ypT0), 79 (33%) had 1% to 25% residual cancer, 91 (38%) had 26% to 75%, and 45 (19%) had >75%. Survival was worse with increasing residual primary cancer, plateauing at 75%. Greater residual primary cancer was associated with worse survival across the spectrum of higher ypTN. Higher ypT, larger number of positive nodes, and use of induction chemotherapy rather than induction chemoradiotherapy were associated with greater residual primary cancer. Less residual primary cancer in response to preoperative therapy is associated with a linear increase in survival after esophagectomy for locally advanced esophageal adenocarcinoma; however, survival is poorer than for resected early-stage cancers. Therefore, for patients with poor prognostic indicators, including higher percentage of residual primary cancer, the role of adjuvant therapy needs to be further examined in an attempt to improve survival. Copyright © 2016. Published by Elsevier Inc.

  5. Residual entanglement and sudden death: A direct connection

    NASA Astrophysics Data System (ADS)

    de Oliveira, J. G. G.; Peixoto de Faria, J. G.; Nemes, M. C.

    2011-11-01

    We explore the results of [V. Coffman, et al., Phys. Rev. A 61 (2000) 052306] derived for general tripartite states in a dynamical context. We study a class of physically motivated tripartite systems. We show that whenever entanglement sudden death occurs in one of the partitions residual entanglement will appear. For fourpartite systems however, the appearance of residual entanglement is not conditioned by sudden death of entanglement. We can only say that if sudden death of entanglement occurs in some partition there will certainly be residual entanglement.

  6. Residual Defect Density in Random Disks Deposits.

    PubMed

    Topic, Nikola; Pöschel, Thorsten; Gallas, Jason A C

    2015-08-03

    We investigate the residual distribution of structural defects in very tall packings of disks deposited randomly in large channels. By performing simulations involving the sedimentation of up to 50 × 10(9) particles we find all deposits to consistently show a non-zero residual density of defects obeying a characteristic power-law as a function of the channel width. This remarkable finding corrects the widespread belief that the density of defects should vanish algebraically with growing height. A non-zero residual density of defects implies a type of long-range spatial order in the packing, as opposed to only local ordering. In addition, we find deposits of particles to involve considerably less randomness than generally presumed.

  7. Urban tree and woody yard residues : another wood resource

    Treesearch

    David B. McKeever; Kenneth E. Skog

    2003-01-01

    Urban tree and woody yard residues are an important component of the municipal solid waste (MSW) stream in the United States. In 2000, approximately 14.5 million tons of urban tree and woody yard residues was generated, nearly 7% of total MSW. Some woody residues are being recovered for recycling, composting, or other uses, but a large proportion is simply discarded....

  8. Nitrogen dynamics post-harvest: the role of woody residues

    Treesearch

    Kathryn Piatek

    2007-01-01

    The role of woody residues in N dynamics in harvested forests has not been fully elucidated. Woody residues have been found to be an N sink, N source, and N neutral in different studies. To understand the implications of each of these scenarios, post-harvest N dynamics in high- and no- woody residue treatments were modeled for a Douglas-fir ecosystem. Nitrogen...

  9. The Importance of Residual Kidney Function in Haemodialysis Patients.

    PubMed

    Kong, Jessica; Davies, Matthew; Mount, Peter

    2018-06-19

    In contrast to peritoneal dialysis, residual kidney function is commonly disregarded for haemodialysis patients, and not regularly monitored or taken into account in routine clinical care. This is despite evidence that higher levels of residual kidney function in haemodialysis patients associate with better outcomes including survival, total solute clearance, nutrition, inflammation, and fluid balance. This review aims to summarise the clinical effects of residual kidney function specifically in haemodialysis patients. Some level of residual kidney function is present in over 80% of patients at the time of dialysis initiation, and while this declines over time, up to 30% of patients on haemodialysis for 5 years still have a measurable level of native kidney function. There is little evidence on how best to preserve residual kidney function in haemodialysis patients, although it has been observed that intensive haemodialysis regimens in incident haemodialysis patients appear to accelerate residual kidney function decline. Residual kidney function is not commonly factored in to haemodialysis prescription and measures of adequacy, despite the fact that some guidelines such as KDOQI and European Best Practice Guidelines suggest that it is reasonable to do. This likely relates, at least in part, to perceived concerns regarding the inconvenience of timed urine collections, and to the complexity and lack of consensus regarding the methods for integrating the intermittent clearance of haemodialysis with the continuous clearance of native renal function. Further research is required into how best to maintain and maximise the benefits of residual kidney function in haemodialysis patients. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

  10. Residual stress in glass: indentation crack and fractography approaches

    PubMed Central

    Anunmana, Chuchai; Anusavice, Kenneth J.; Mecholsky, John J.

    2009-01-01

    Objective To test the hypothesis that the indentation crack technique can determine surface residual stresses that are not statistically significantly different from those determined from the analytical procedure using surface cracks, the four-point flexure test, and fracture surface analysis. Methods Soda-lime-silica glass bar specimens (4 mm × 2.3 mm × 28 mm) were prepared and annealed at 650 °C for 30 min before testing. The fracture toughness values of the glass bars were determined from 12 specimens based on induced surface cracks, four-point flexure, and fractographic analysis. To determine the residual stress from the indentation technique, 18 specimens were indented under 19.6 N load using a Vickers microhardness indenter. Crack lengths were measured within 1 min and 24 h after indentation, and the measured crack lengths were compared with the mean crack lengths of annealed specimens. Residual stress was calculated from an equation developed for the indentation technique. All specimens were fractured in a four-point flexure fixture and the residual stress was calculated from the strength and measured crack sizes on the fracture surfaces. Results The results show that there was no significant difference between the residual stresses calculated from the two techniques. However, the differences in mean residual stresses calculated within 1 min compared with those calculated after 24 h were statistically significant (p=0.003). Significance This study compared the indentation technique with the fractographic analysis method for determining the residual stress in the surface of soda-lime silica glass. The indentation method may be useful for estimating residual stress in glass. PMID:19671475

  11. Persistence and bioaccumulation of oxyfluorfen residues in onion.

    PubMed

    Sondhia, Shobha

    2010-03-01

    A field study was conducted to determine persistence and bioaccumulation of oxyflorfen residues in onion crop at two growth stages. Oxyfluorfen (23.5% EC) was sprayed at 250 and 500 g ai/ha on the crop (variety, N53). Mature onion and soil samples were collected at harvest. Green onion were collected at 55 days from each treated and control plot and analyzed for oxyfluorfen residues by a validated high-performance liquid chromatography method with an accepted recovery of 78-92% at the minimum detectable concentration of 0.003 microg g(-1). Analysis showed 0.015 and 0.005 microg g(-1) residues of oxyfluorfen at 250 g a.i. ha(-1) rate in green and mature onion samples, respectively; however, at 500 g a.i.ha(-1) rates, 0.025 and 0.011 microg g(-1) of oxyfluorfen residues were detected in green and mature onion samples, respectively. Soil samples collected at harvest showed 0.003 and 0.003 microg g(-1) of oxyfluorfen residues at the doses 250 and 500 g a.i. ha(-1), respectively. From the study, a pre-harvest interval of 118 days for onion crop after the herbicide application is suggested.

  12. Prediction of distal residue participation in enzyme catalysis

    PubMed Central

    Brodkin, Heather R; DeLateur, Nicholas A; Somarowthu, Srinivas; Mills, Caitlyn L; Novak, Walter R; Beuning, Penny J; Ringe, Dagmar; Ondrechen, Mary Jo

    2015-01-01

    A scoring method for the prediction of catalytically important residues in enzyme structures is presented and used to examine the participation of distal residues in enzyme catalysis. Scores are based on the Partial Order Optimum Likelihood (POOL) machine learning method, using computed electrostatic properties, surface geometric features, and information obtained from the phylogenetic tree as input features. Predictions of distal residue participation in catalysis are compared with experimental kinetics data from the literature on variants of the featured enzymes; some additional kinetics measurements are reported for variants of Pseudomonas putida nitrile hydratase (ppNH) and for Escherichia coli alkaline phosphatase (AP). The multilayer active sites of P. putida nitrile hydratase and of human phosphoglucose isomerase are predicted by the POOL log ZP scores, as is the single-layer active site of P. putida ketosteroid isomerase. The log ZP score cutoff utilized here results in over-prediction of distal residue involvement in E. coli alkaline phosphatase. While fewer experimental data points are available for P. putida mandelate racemase and for human carbonic anhydrase II, the POOL log ZP scores properly predict the previously reported participation of distal residues. PMID:25627867

  13. Pesticide residue quantification analysis by hyperspectral imaging sensors

    NASA Astrophysics Data System (ADS)

    Liao, Yuan-Hsun; Lo, Wei-Sheng; Guo, Horng-Yuh; Kao, Ching-Hua; Chou, Tau-Meu; Chen, Junne-Jih; Wen, Chia-Hsien; Lin, Chinsu; Chen, Hsian-Min; Ouyang, Yen-Chieh; Wu, Chao-Cheng; Chen, Shih-Yu; Chang, Chein-I.

    2015-05-01

    Pesticide residue detection in agriculture crops is a challenging issue and is even more difficult to quantify pesticide residue resident in agriculture produces and fruits. This paper conducts a series of base-line experiments which are particularly designed for three specific pesticides commonly used in Taiwan. The materials used for experiments are single leaves of vegetable produces which are being contaminated by various amount of concentration of pesticides. Two sensors are used to collected data. One is Fourier Transform Infrared (FTIR) spectroscopy. The other is a hyperspectral sensor, called Geophysical and Environmental Research (GER) 2600 spectroradiometer which is a batteryoperated field portable spectroradiometer with full real-time data acquisition from 350 nm to 2500 nm. In order to quantify data with different levels of pesticide residue concentration, several measures for spectral discrimination are developed. Mores specifically, new measures for calculating relative power between two sensors are particularly designed to be able to evaluate effectiveness of each of sensors in quantifying the used pesticide residues. The experimental results show that the GER is a better sensor than FTIR in the sense of pesticide residue quantification.

  14. TENORM: Wastewater Treatment Residuals

    EPA Pesticide Factsheets

    Water and wastes which have been discharged into municipal sewers are treated at wastewater treatment plants. These may contain trace amounts of both man-made and naturally occurring radionuclides which can accumulate in the treatment plant and residuals.

  15. HLA amino acid residue matching in 2575 kidney transplants.

    PubMed

    Tan, J; Qiu, J; Tang, X

    2007-06-01

    Donor-recipient HLA matching was retrospectively evaluated in 2575 renal transplants by comparing amino acid residue matches (Res M) with conventional six-antigen matches (Ag M). Only 6% of donor-recipient combinations had 0 to 1 mismatches using Ag M, whereas 42.8% of the recipients had no mismatch by Res M. Compared with the first year results of residue mismatched recipients, the 1102 patients with 0 residue mismatching displayed a low incidence of rejection (12.07% vs 5.37%) and less anti-HLA antibody production (class I 13.76 vs 38.12%; class II 7.66% vs 31.11%). The 1-to 10-year graft survival of the residue-matched group was similar to that of the Ag-matched group, and significantly better than the residue-mismatched recipients. In summary, Res M could be a good matching system for renal transplantation in the Han population.

  16. Drug and chemical residues in domestic animals.

    PubMed

    Mussman, H C

    1975-02-01

    Given the large number of chemical substances that may find their way into the food supply, a system is needed to monitor their presence. The U. S. Department of Agriculture's Meat and Poultry Inspection Program routinely tests for chemical residues in animals coming to slaughter. Pesticides, heavy metals, growth promotants (hormones and hormonelike agents), and antibiotics are included. Samples are taken statistically so that inferences as to national incidence of residues can be drawn. When a problem is identified, a more selective sampling is designed to help follow up on the initial regulatory action. In testing for pesticides, only DDT and dieldrin are found with any frequency and their levels are decreasing; violative residues of any chlorinated hydrocarbon are generally a result of an industrial accident rather than agricultural usage. Analyses for heavy metals have revealed detectable levels of mercury, lead, and others, but none at levels that are considered a health hazard. Of the hormone or hormonelike substances, only diethylstilbestrol has been a residue problem and its future is uncertain. The most extensive monitoring for veterinary drugs is on the antimicrobials, including sulfonamides, streptomycin, and the tetracycline group of antibiotics that constitute the bulk of the violations; their simultaneous use prophylactically and therapeutically has contributed to the problem in certain cases. A strong, well-designed user education program on proper application of pesticides, chemicals, and veterinary drugs appears to be one method of reducing the incidence of unwanted residues.

  17. Pyrolysis of Woody Residues: Impact of Mineral Content

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Iisa, Kristiina; Zacher, Alan; Sykes, Robert

    2014-11-21

    Woody residues represent a lower cost option for feedstocks for the production of biofuels. In this study, the pyrolysis of woody residues was investigated as part of Clean Energy Dialogue between the U.S. and Canada. Three pine-based hog fuels from saw mills and wood from pine beetle killed trees were chosen as the woody residue feedstocks and pine and birch as the reference clean feedstocks. The yields and quality of the oil were evaluated in a bubbling fluidized bed reactor and a laboratory-scale pyrolyzer connected to a molecular beam mass spectrometer.

  18. Measurement of residual stresses by the moire method

    NASA Astrophysics Data System (ADS)

    Sciammarella, C. A.; Albertazzi, A., Jr.

    Three different applications of the moire method to the determination of residual stresses and strains are presented. The three applications take advantage of the property of ratings to record the changes of the surface they are printed on. One of the applications deals with thermal residual stresses, another with contact residual stress and the third one is a generalization of the blind hole technique. This last application is based on a computer assisted moire technique and on the generalization of the quasi-heterodyne techniques of fringe pattern analysis.

  19. 40 CFR 180.176 - Mancozeb; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Asparagus (negligible residue) 0.1 Banana 4.0 Banana, pulp 0.5 Barley, bran 20 Barley, flour 20 Barley..., straw 25 Onion, bulb 0.5 Papaya (whole fruit with no residue present in the edible pulp after the peel...

  20. Ratios for estimating logging residue in the Pacific Northwest.

    Treesearch

    James O. Howard

    1981-01-01

    Ratios are presented for estimating the volume of logging residue for any location in Idaho, Washington, and Oregon. They show cubic-foot volume of logging residue per 1,000 board feet of timber harvested and per acre harvested. Tables show gross and net volumes, with and without bark. The volumes of live and dead and cull residue at the time of harvest are also given...

  1. Cation and anion leaching and growth of Acacia saligna in bauxite residue sand amended with residue mud, poultry manure and phosphogypsum.

    PubMed

    Jones, B E H; Haynes, R J; Phillips, I R

    2012-03-01

    To examine (1) the effect of organic (poultry manure) and inorganic (residue mud and phosphogypsum) amendments on nutrient leaching losses from residue sand and (2) whether amendments improve the growth of plants in residue sand. Leaching columns were established using residue sand. The phosphogypsum-treated surface layer (0-15 cm) was amended with poultry manure and/or bauxite residue mud and the subsurface layer (15-45 cm) was either left untreated or amended with phosphogypsum. Much of the Na⁺, K⁺, Cl⁻ and SO₄²⁻ was lost during the first four leachings. Additions of phosphogypsum to both surface and subsurface layers resulted in partial neutralization of soluble alkalinity. Mean pH of leachates ranged from 8.0 to 8.4, the major cation leached was Na⁺ and the major balancing anion was SO₄²⁻ . Where gypsum was not applied to the subsurface, mean pH of leachates was 10.0-10.9, the main cation leached was still Na⁺ and the main balancing anions were a combination of SO₄²⁻ and HCO₃⁻/CO₃²⁻. At the end of the experiment, concentrations of exchangeable Na⁺ in the subsurface layers were similar regardless of whether gypsum had been applied to that layer or not. Yields of Acacia saligna were promoted by additions of poultry manure to the surface layer but unaffected by gypsum incorporation into the subsurface layer. Lack of reaction of phosphogypsum with the subsurface layer is unlikely to be a major factor limiting revegetation of residue sand since in the absence of phosphogypsum the excess Na⁺ leaches with the residual alkalinity (HCO₃⁻/CO₃²⁻) rather than SO₄²⁻.

  2. Distribution of pesticide residues in soil and uncertainty of sampling.

    PubMed

    Suszter, Gabriela K; Ambrus, Árpád

    2017-08-03

    Pesticide residues were determined in about 120 soil cores taken randomly from the top 15 cm layer of two sunflower fields about 30 days after preemergence herbicide treatments. Samples were extracted with acetone-ethyl acetate mixture and the residues were determined with GC-TSD. Residues of dimethenamid, pendimethalin, and prometryn ranged from 0.005 to 2.97 mg/kg. Their relative standard deviations (CV) were between 0.66 and 1.13. The relative frequency distributions of residues in soil cores were very similar to those observed in root and tuber vegetables grown in pesticide treated soils. Based on all available information, a typical CV of 1.00 was estimated for pesticide residues in primary soil samples (soil cores). The corresponding expectable relative uncertainty of sampling is 20% when composite samples of size 25 are taken. To obtain a reliable estimate of the average residues in the top 15 cm layer of soil of a field up to 8 independent replicate random samples should be taken. To obtain better estimate of the actual residue level of the sampled filed would be marginal if larger number of samples were taken.

  3. Mineralogy of chondritic interplanetary dust particle impact residues from LDEF

    NASA Technical Reports Server (NTRS)

    Barrett, R. A.; Zolensky, M. E.; Bernhard, R.

    1993-01-01

    A detailed structural and compositional analysis of several impactor residues was performed utilizing transmission electron microscopy, energy dispersive spectroscopy, and electron diffraction. Residues from the interior of several craters in gold surfaces were removed with a tungsten needle, mounted in EMBED-812 epoxy, and ultramicrotomed. The presence in these residues of equilibrated ferromagnesian minerals, recrystallization textures, glass, and melted metal and sulfide bodies decorating grain boundaries is indicative of varying degrees of shock metamorphism in all impact residues we have characterized.

  4. Plasma treatment of air pollution control residues.

    PubMed

    Amutha Rani, D; Gomez, E; Boccaccini, A R; Hao, L; Deegan, D; Cheeseman, C R

    2008-01-01

    Air pollution control (APC) residues from waste incineration have been blended with silica and alumina and the mix melted using DC plasma arc technology. The chemical composition of the fully amorphous homogeneous glass formed has been determined. Waste acceptance criteria compliance leach testing demonstrates that the APC residue derived glass releases only trace levels of heavy metals (Pb (<0.007mg/kg) and Zn (0.02mg/kg)) and Cl(-) (0.2mg/kg). These are significantly below the limit values for disposal to inert landfill. It is concluded that plasma treatment of APC residues can produce an inert glass that may have potential to be used either in bulk civil engineering applications or in the production of higher value glass-ceramic products.

  5. Study on leaching of pollutants from vegetable tanning residue.

    PubMed

    Mazumder, Debabrata; Biswas, Santosh; Bandyopadhyay, Pratip

    2006-07-01

    The processing of heavy leather employs the vegetable tanning method involving use of tan liquor. The solid residue of this vegetable tanning process aggravates the water pollution by means of leaching of tannin and other associatedpollutants. Tannin is a biologically resistant compound causing several problems in animal body. The present study dealt with the pollution hazard arising out of leaching of pollutants from the open dumped vegetable tanning residue by rainfall washing. The concerned pollutants were pH, Chemical Oxygen Demand (COD), tannin,sulfate and chloride concentration. To explore the possible extent of contamination of these pollutants in the leached water, two different masses (2 kg and 3 kg) of tanning residue were employed. The results of the study showed that there was a continuous release of pollutants from the vegetable tanning residue. Moreover, there was no regular variation in various pollutant concentrations in both the cases solely due to non-homogeneity of the residue.

  6. MODELING DISINFECTANT RESIDUALS IN DRINKING-WATER STORAGE TANKS

    EPA Science Inventory

    The factors leading to the loss of disinfectant residual in well-mixed drinking-water storage tanks are studied. Equations relating disinfectant residual to the disinfectant's reation rate, the tank volume, and the fill and drain rates are presented. An analytical solution for ...

  7. Dimensional Characteristics of Hardwood Top and Limb Residue

    Treesearch

    Nels S. Christopherson

    1983-01-01

    Sawtimber harvesting in northern hardwood stands leaves behind a large amount of residue in the form of tops and limbs. This paper presents typical dimensional characteristics of residue for northern hardwood tops incluting data on lengths, widths, diameters, and complete branch details.

  8. 40 CFR 180.350 - Nitrapyrin; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Nitrapyrin; tolerances for residues. 180.350 Section 180.350 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... residues of the soil microbiocide nitrapyrin [2-chloro-6-(trichloromethyl) pyridine] and its metabolite, 6...

  9. 40 CFR 180.337 - Oxytetracycline; tolerance for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Oxytetracycline; tolerance for... § 180.337 Oxytetracycline; tolerance for residues. Tolerances are established for residues of the pesticide oxytetracycline in or on the following raw agricultural commodities: Commodity Parts per million...

  10. Hazardous properties of paint residues from the furniture industry.

    PubMed

    Vaajasaari, Kati; Kulovaara, Maaret; Joutti, Anneli; Schultz, Eija; Soljamo, Kari

    2004-01-30

    The objective of this study was to screen nine excess paint residues for environmental hazard and to evaluate their disposability in a non-hazardous or hazardous-waste landfill. These residues were produced in the process of spray-painting furniture. Residues were classified according to their leaching and ecotoxicological properties. Leaching properties were determined with the European standard SFS-EN 12457-2 leaching-test. The toxicity of the leaching-test eluates was measured with plant-, bacteria- and enzyme-inhibition bioassays. Total organic carbon, formaldehyde and solvent concentrations in the solid wastes and in the leaching-test eluates were analysed. It seemed likely that leached formaldehyde caused very high acute toxicity in leaching-test eluates of the dry-booth residues. This hypothesis was based on the fact that the formaldehyde concentrations in the leaching-test eluates of the dry-booth residues were 62-75 times higher than the EC50 value reported in the literature for formaldehyde. The results of the water-curtain booth residues showed that the samples with the highest TOC and aromatic solvent concentrations were also the most toxic. The studied excess paint residues were complex organic mixtures and contained large amounts of compounds not identifiable from chemical data. Therefore, the evaluation of the hazard based solely on available chemical data is unlikely to be sufficient, as evidenced by our study. Our results show that harmful compounds remain in the solid waste and the toxicity results of their leaching-test eluates show that toxicity may leach from residues in contact with water at landfill sites. They also confirm the benefit of combining chemical and ecotoxicological assays in assessing the potential environmental hazard of complex organic mixtures found in wastes. Copyright 2003 Elsevier B.V.

  11. Detecting Signatures of GRACE Sensor Errors in Range-Rate Residuals

    NASA Astrophysics Data System (ADS)

    Goswami, S.; Flury, J.

    2016-12-01

    In order to reach the accuracy of the GRACE baseline, predicted earlier from the design simulations, efforts are ongoing since a decade. GRACE error budget is highly dominated by noise from sensors, dealiasing models and modeling errors. GRACE range-rate residuals contain these errors. Thus, their analysis provides an insight to understand the individual contribution to the error budget. Hence, we analyze the range-rate residuals with focus on contribution of sensor errors due to mis-pointing and bad ranging performance in GRACE solutions. For the analysis of pointing errors, we consider two different reprocessed attitude datasets with differences in pointing performance. Then range-rate residuals are computed from these two datasetsrespectively and analysed. We further compare the system noise of four K-and Ka- band frequencies of the two spacecrafts, with range-rate residuals. Strong signatures of mis-pointing errors can be seen in the range-rate residuals. Also, correlation between range frequency noise and range-rate residuals are seen.

  12. Residual strength of GFR/POM as a function of damage

    NASA Astrophysics Data System (ADS)

    Zachariev, G.; Rudolph, H.-V.; Ivers, H.

    2010-07-01

    A relation between the residual strength and the dispersed damage accumulated in a short fiber reinforced polyoximethylene (GFR/POM) samples under tension is found. For that purpose dependencies of damage and residual strength on loading percentage are used. Damage as a function of loading percentage is known for the material under study. To find the dependency of residual strength on loading percentage a subsidiary function is introduced and a method is proposed for determination of the parameters in the dependency on the basis of the experimental data. Both damage and residual strength are measured after unloading samples that have been loaded applying different loading percentages. Damage is the accumulation of new internal surfaces that arise under mechanical loading in the whole volume of the material. They are registered by a new original method of X-ray refraction. The analytical relation between the residual strength and damage accumulated is compared to the experimental results found for the residual strength under different damage degrees.

  13. Organochlorine insecticide residues in ducklings and their dilution by growth.

    PubMed

    Charnetski, W A

    1976-08-01

    Residues of DDT, DDD, DDE, and dieldrin in 7 species of ducklings from Alberta, Canada, were measured. Levels of DDT and metabolites ranged from 0 to 36.48 ppm in fat of 96% of the birds and from 0 to 0.97 ppm im muscle from 67% of the birds. Residue levels of dieldrin ranged from 0 to 2.62 ppm in fat and from 0 to 0.11 ppm in muscle of 43 and 19% of the birds, respectively. Growth dilution was considered to be the most significant factor in reducing the insecticide residue levels in the ducklings. DDT (total DDT, DDE, and DDD) residue levels were decreased with increased weight of pintail (A. acuta), baldpate (Mareca americana), and gadwall (A. strepera) ducklings. Dieldrin used in grasshopper control did not contribute to residue levels in the ducklings. Contamination by DDT was considered to have originated from outside the habitat. No dieldrin or DDT residues were found in ducklings' food sources analysed.

  14. Aqueous Electrochemical Mechanisms in Actinide Residue Processing

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Morris, David E.; Burns, Carol J.; Smith, Wayne H.

    2000-12-31

    Plutonium and uranium residues (e.g., incinerator ash, combustibles, and sand/slag/crucibles) resulting from the purification and processing of nuclear materials constitute an enormous volume of ''lean'' processing waste and represent a significant fraction of the U. S. Department of Energy's (DOE) legacy waste from fifty years of nuclear weapons production activities. Much of this material is presently in storage at sites throughout the DOE weapons production complex (most notably Rocky Flats, Savannah River and Hanford) awaiting further processing and/or final disposition. The chemical and physical stability of much of this material has been called into question recently by the Defense Nuclearmore » Facility Safety Board (DNFSB) and resulted in the issuance of a mandate by the DNFSB to undertake a program to stabilize these materials [1]. The ultimate disposition for much of these materials is anticipated to be geologic repositories such as the proposed Waste Isolation Pilot Plant in New Mexico. However, in light of the mandate to stabilize existing residues and the probable concomitant increase in the volume of material to be disposed as a result of stabilization (e.g., from repackaging at lower residue densities), the projected storage volume for these wastes within anticipated geologic repositories will likely be exceeded simply to handle existing wastes. Additional processing of some of these residue waste streams to reduce radionuclide activity levels, matrix volume, or both is a potentially important strategy to achieve both stabilization and volume reduction so that the anticipated geologic repositories will provide adequate storage volume. In general, the plutonium and uranium that remains in solid residue materials exists in a very stable chemical form (e.g., as binary oxides), and the options available to remove the actinides are limited. However, there have been some demonstrated successes in this vain using aqueous phase electrochemical methods such

  15. Residual stresses and their effects in composite laminates

    NASA Technical Reports Server (NTRS)

    Hahn, H. T.; Hwang, D. G.

    1983-01-01

    Residual stresses in composite laminates are caused by the anisotropy in expansional properties of constituent unidirectional plies. The effect of these residual stresses on dimensional stability is studied through the warping of unsymmetric (0 sub 4/90 sub 4)sub T graphite/epoxy laminates while their effect on ply failure is analyzed for (0/90)sub 2s Kevlar 49/epoxy laminate. The classical laminated plate theory is used to predict the warping of small and large panels. The change of warping does not indicate a noticeable stress relaxation at 75 C while it is very sensitive to moisture content and hence to environment. A prolonged gellation at the initial cure temperature reduces residual stresses while postcure does not. The matrix/interface cracking in dry (0/90)sub 2s Kevlar 49/epoxy laminate is shown to be the result of the residual stress exceeding the transverse strength.

  16. Continuous Removal of Coal-Gasification Residue

    NASA Technical Reports Server (NTRS)

    Collins, Earl R., Jr.; Suitor, J.; Dubis, D.

    1986-01-01

    Continuous-flow hopper processes solid residue from coal gasification, converting it from ashes, cinders, and clinkers to particles size of sand granules. Unit does not require repeated depressurization of lockhopper to admit and release materials. Therefore consumes less energy. Because unit has no airlock valves opened and closed repeatedly on hot, abrasive particles, subjected to lesser wear. Coal-gasification residue flows slowly through pressure-letdown device. Material enters and leaves continuously. Cleanout door on each pressure-letdown chamber allows access for maintenance and emergencies.

  17. A Residual Mass Ballistic Testing Method to Compare Armor Materials or Components (Residual Mass Ballistic Testing Method)

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Benjamin Langhorst; Thomas M Lillo; Henry S Chu

    2014-05-01

    A statistics based ballistic test method is presented for use when comparing multiple groups of test articles of unknown relative ballistic perforation resistance. The method is intended to be more efficient than many traditional methods for research and development testing. To establish the validity of the method, it is employed in this study to compare test groups of known relative ballistic performance. Multiple groups of test articles were perforated using consistent projectiles and impact conditions. Test groups were made of rolled homogeneous armor (RHA) plates and differed in thickness. After perforation, each residual projectile was captured behind the target andmore » its mass was measured. The residual masses measured for each test group were analyzed to provide ballistic performance rankings with associated confidence levels. When compared to traditional V50 methods, the residual mass (RM) method was found to require fewer test events and be more tolerant of variations in impact conditions.« less

  18. On Lagrangian residual currents with applications in south San Francisco Bay, California

    USGS Publications Warehouse

    Cheng, Ralph T.; Casulli, Vincenzo

    1982-01-01

    The Lagrangian residual circulation has often been introduced as the sum of the Eulerian residual circulation and the Stokes' drift. Unfortunately, this definition of the Lagrangian residual circulation is conceptually incorrect because both the Eulerian residual circulation and the Stokes' drift are Eulerian variables. In this paper a classification of various residual variables are reviewed and properly defined. The Lagrangian residual circulation is then studied by means of a two-stage formulation of a computer model. The tidal circulation is first computed in a conventional Eulerian way, and then the Lagrangian residual circulation is determined by a method patterned after the method of markers and cells. To demonstrate properties of the Lagrangian residual circulation, application of this approach in South San Francisco Bay, California, is considered. With the aid of the model results, properties of the Eulerian and Lagrangian residual circulation are examined. It can be concluded that estimation of the Lagrangian residual circulation from Eulerian data may lead to unacceptable error, particularly in a tidal estuary where the tidal excursion is of the same order of magnitude as the length scale of the basin. A direction calculation of the Lagrangian residual circulation must be made and has been shown to be feasible.

  19. The Study of Residual Voltage of Induction Motor and the Influence of Various Parameters on the Residual Voltage

    NASA Astrophysics Data System (ADS)

    Zhang, Shuping; Zhao, Chen; Tan, Weipu

    2017-05-01

    The majority important load of industrial area is mainly composed of induction motor, it is more common that induction motor becomes sluggishness and even tripping due to the lose of power supply or other malfunction in the practical work. In this paper, space vector method is used to establish a reduced order model of induction motor, and then study the changes of motor electromagnetic after losing electricity. Based on motion equations of the rotor and magnetic flux conservation principle, it uses mathematical methods to deduce the expression of rotor current, rotor flux, the stator flux and the residual voltage of stator side. In addition, relying on thermal power plants, it uses the actual data of power plants, takes DIgsilent software to simulate the residual voltage of motor after losing electricity. analyses the influence on the residual voltage with the changes of the moment of inertia, load ratio, initial size of slip and the load characteristic of induction motor. By analysis of these, it has a more detailed understanding about the changes of residual voltage in practical application, in additional, it is more beneficial to put into standby power supply safely and effectively, moreover, reduce the influence of the input process to the whole system.

  20. Evaluation of pesticide residues in fruits and vegetables from Algeria.

    PubMed

    Mebdoua, Samira; Lazali, Mohamed; Ounane, Sidi Mohamed; Tellah, Sihem; Nabi, Fahima; Ounane, Ghania

    2017-06-01

    A total of 160 samples of 13 types of fresh fruits and vegetables from domestic production and import were analysed to detect the presence of pesticide residues. Analysis was performed by multi-residual extraction followed by gas chromatography-mass spectrometry. In 42.5% of the tested samples, no residues were found and 12.5% of samples contained pesticide residues above maximum residue limits. Risk assessment for long-term exposure was done for all pesticides detected in this study. Except chlorpyrifos and lambda-cyhalothrin, exposure to pesticides from vegetables and fruits was below 1% of the acceptable daily intake. Short-term exposure assessment revealed that in seven pesticide/commodity combinations, including three pesticides (chlorpyrifos, deltamethrin and lambda-cyhalothrin), the acute reference dose had been exceeded.

  1. Blast furnace residues for arsenic removal from mining-contaminated groundwater.

    PubMed

    Carrillo-Pedroza, Fco Raúl; Soria-Aguilar, Ma de Jesús; Martínez-Luevanos, Antonia; Narvaez-García, Víctor

    2014-01-01

    In this work, blast furnace (BF) residues were well characterized and then evaluated as an adsorbent material for arsenic removal from a mining-contaminated groundwater. The adsorption process was analysed using the theories of Freundlich and Langmuir. BF residues were found to be an effective sorbent for As (V) ions. The modelling of adsorption isotherms by empirical models shows that arsenate adsorption is fitted by the Langmuir model, suggesting a monolayer adsorption of arsenic onto adsorbents. Arsenate adsorption onto BF residue is explained by the charge density surface affinity and by the formation of Fe (II) and Fe (III) corrosion products onto BF residue particles. The results indicate that BF residues represent an attractive low-cost absorbent option for the removal of arsenic in wastewater treatment.

  2. A deep learning framework for improving long-range residue-residue contact prediction using a hierarchical strategy.

    PubMed

    Xiong, Dapeng; Zeng, Jianyang; Gong, Haipeng

    2017-09-01

    Residue-residue contacts are of great value for protein structure prediction, since contact information, especially from those long-range residue pairs, can significantly reduce the complexity of conformational sampling for protein structure prediction in practice. Despite progresses in the past decade on protein targets with abundant homologous sequences, accurate contact prediction for proteins with limited sequence information is still far from satisfaction. Methodologies for these hard targets still need further improvement. We presented a computational program DeepConPred, which includes a pipeline of two novel deep-learning-based methods (DeepCCon and DeepRCon) as well as a contact refinement step, to improve the prediction of long-range residue contacts from primary sequences. When compared with previous prediction approaches, our framework employed an effective scheme to identify optimal and important features for contact prediction, and was only trained with coevolutionary information derived from a limited number of homologous sequences to ensure robustness and usefulness for hard targets. Independent tests showed that 59.33%/49.97%, 64.39%/54.01% and 70.00%/59.81% of the top L/5, top L/10 and top 5 predictions were correct for CASP10/CASP11 proteins, respectively. In general, our algorithm ranked as one of the best methods for CASP targets. All source data and codes are available at http://166.111.152.91/Downloads.html . hgong@tsinghua.edu.cn or zengjy321@tsinghua.edu.cn. Supplementary data are available at Bioinformatics online. © The Author (2017). Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com

  3. Residual stress alleviation of aircraft metal structures reinforced with filamentary composites

    NASA Technical Reports Server (NTRS)

    Kelly, J. B.; June, R. R.

    1973-01-01

    Methods to eliminate or reduce residual stresses in aircraft metal structures reinforced by filamentary composites are discussed. Residual stress level reductions were achieved by modifying the manufacturing procedures used during adhesive bonding. The residual stress alleviation techniques involved various forms of mechanical constraint which were applied to the components during bonding. Nine methods were evaluated, covering a wide range in complexity. All methods investigated during the program affected the residual stress level. In general, residual stresses were reduced by 70 percent or more from the stress level produced by conventional adhesive bonding procedures.

  4. 40 CFR 180.317 - Propyzamide; tolerances for residues.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... the herbicide propyzamide, including its metabolites and degradates, in or on the commodities in the... defined in § 180.1(l), are established for residues of the herbicide propyzamide, including its... for indirect or inadvertent residues of the herbicide propyzamide, including its metabolites and...

  5. 40 CFR 180.317 - Propyzamide; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... the herbicide propyzamide, including its metabolites and degradates, in or on the commodities in the... defined in § 180.1(l), are established for residues of the herbicide propyzamide, including its... for indirect or inadvertent residues of the herbicide propyzamide, including its metabolites and...

  6. 40 CFR 180.317 - Propyzamide; tolerances for residues.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... the herbicide propyzamide, including its metabolites and degradates, in or on the commodities in the... defined in § 180.1(l), are established for residues of the herbicide propyzamide, including its... for indirect or inadvertent residues of the herbicide propyzamide, including its metabolites and...

  7. 40 CFR 180.317 - Propyzamide; tolerances for residues.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... the herbicide propyzamide, including its metabolites and degradates, in or on the commodities in the... defined in § 180.1(l), are established for residues of the herbicide propyzamide, including its... for indirect or inadvertent residues of the herbicide propyzamide, including its metabolites and...

  8. 40 CFR 180.300 - Ethephon; tolerances for residues.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 25 2013-07-01 2013-07-01 false Ethephon; tolerances for residues. 180.300 Section 180.300 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.300...

  9. Prediction of distal residue participation in enzyme catalysis.

    PubMed

    Brodkin, Heather R; DeLateur, Nicholas A; Somarowthu, Srinivas; Mills, Caitlyn L; Novak, Walter R; Beuning, Penny J; Ringe, Dagmar; Ondrechen, Mary Jo

    2015-05-01

    A scoring method for the prediction of catalytically important residues in enzyme structures is presented and used to examine the participation of distal residues in enzyme catalysis. Scores are based on the Partial Order Optimum Likelihood (POOL) machine learning method, using computed electrostatic properties, surface geometric features, and information obtained from the phylogenetic tree as input features. Predictions of distal residue participation in catalysis are compared with experimental kinetics data from the literature on variants of the featured enzymes; some additional kinetics measurements are reported for variants of Pseudomonas putida nitrile hydratase (ppNH) and for Escherichia coli alkaline phosphatase (AP). The multilayer active sites of P. putida nitrile hydratase and of human phosphoglucose isomerase are predicted by the POOL log ZP scores, as is the single-layer active site of P. putida ketosteroid isomerase. The log ZP score cutoff utilized here results in over-prediction of distal residue involvement in E. coli alkaline phosphatase. While fewer experimental data points are available for P. putida mandelate racemase and for human carbonic anhydrase II, the POOL log ZP scores properly predict the previously reported participation of distal residues. 2015 The Authors Protein Science published by Wiley Periodicals, Inc. on behalf of The Protein Society.

  10. Evolution and the Distribution of Glutaminyl and Asparaginyl Residues in Proteins

    PubMed Central

    Robinson, Arthur B.

    1974-01-01

    Recent experiments on the deamidation of glutaminyl and asparaginyl residues in peptides and proteins support the hypothesis that these residues may serve as molecular clocks that control biological processes. A hypothesis is now offered that suggests that these molecular clocks are set by rejection or accumulation of appropriate sequences of residues including a glutaminyl or asparaginyl residue during evolution. PMID:4522799

  11. 40 CFR 180.385 - Diclofop-methyl; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances... combined residues of the herbicide diclofop-methyl (methyl 2-[4-(2,4-dichlorophenoxy)phenoxy]propanoate...

  12. GLC determination of quinaldine residue in fish

    USGS Publications Warehouse

    Allen, J.L.; Sills, J.B.

    1970-01-01

    A procedure for the determination of quinaldine residue in various fish tissues is described. Homogenized tissues are extracted wi th hexane-ethyl ether, the extracts are concentrated by partitioning through O.IN sulfuric acid, and the residues are measured by alkali Harne ionization gas chromatography. Muscle tissues containing from 0.01 to 10.0 ppm quinaldine were successfully analyzed with recoveries from 75 to 100%.

  13. Phosmet residues in an orchard and adjacent recreational area.

    PubMed

    MacNeil, J D; Hikichi, M

    1986-10-01

    Two cover sprays of phosmet were applied to an orchard adjoining a camping area and a bird sanctuary with a resident goose population. Insecticide residues were monitored on orchard leaves, orchard ground cover, ground cover in the camp-site and along the adjacent lakeshore. Despite attempts to minimize drift, significant spray residues were found outside the target area. Residues on ground cover and leaves were reduced by sprinkler irrigation subsequent to spray application.

  14. Using noble gas tracers to estimate residual CO2 saturation in the field: results from the CO2CRC Otway residual saturation and dissolution test

    NASA Astrophysics Data System (ADS)

    LaForce, T.; Ennis-King, J.; Paterson, L.

    2013-12-01

    Residual CO2 saturation is a critically important parameter in CO2 storage as it can have a large impact on the available secure storage volume and post-injection CO2 migration. A suite of single-well tests to measure residual trapping was conducted at the Otway test site in Victoria, Australia during 2011. One or more of these tests could be conducted at a prospective CO2 storage site before large-scale injection. The test involved injection of 150 tonnes of pure carbon dioxide followed by 454 tonnes of CO2-saturated formation water to drive the carbon dioxide to residual saturation. This work presents a brief overview of the full test sequence, followed by the analysis and interpretation of the tests using noble gas tracers. Prior to CO2 injection krypton (Kr) and xenon (Xe) tracers were injected and back-produced to characterise the aquifer under single-phase conditions. After CO2 had been driven to residual the two tracers were injected and produced again. The noble gases act as non-partitioning aqueous-phase tracers in the undisturbed aquifer and as partitioning tracers in the presence of residual CO2. To estimate residual saturation from the tracer test data a one-dimensional radial model of the near-well region is used. In the model there are only two independent parameters: the apparent dispersivity of each tracer and the residual CO2 saturation. Independent analysis of the Kr and Xe tracer production curves gives the same estimate of residual saturation to within the accuracy of the method. Furthermore the residual from the noble gas tracer tests is consistent with other measurements in the sequence of tests.

  15. Corn residue utilization by livestock in the USA

    USDA-ARS?s Scientific Manuscript database

    Corn (Zea mays L.) residue grazing or harvest provides a simple and economical practice to integrate crops and livestock. Limited information is available on how widespread corn residue utilization is practiced by US producers. In 2010, the USDA-ERS surveyed producers from 19 states on corn grain ...

  16. Residual radioactivity of treated green diamonds.

    PubMed

    Cassette, Philippe; Notari, Franck; Lépy, Marie-Christine; Caplan, Candice; Pierre, Sylvie; Hainschwang, Thomas; Fritsch, Emmanuel

    2017-08-01

    Treated green diamonds can show residual radioactivity, generally due to immersion in radium salts. We report various activity measurements on two radioactive diamonds. The activity was characterized by alpha and gamma ray spectrometry, and the radon emanation was measured by alpha counting of a frozen source. Even when no residual radium contamination can be identified, measurable alpha and high-energy beta emissions could be detected. The potential health impact of radioactive diamonds and their status with regard to the regulatory policy for radioactive products are discussed. Copyright © 2017. Published by Elsevier Ltd.

  17. Neutron diffraction studies of laser welding residual stresses

    NASA Astrophysics Data System (ADS)

    Petrov, Peter I.; Bokuchava, Gizo D.; Papushkin, Igor V.; Genchev, Gancho; Doynov, Nikolay; Michailov, Vesselin G.; Ormanova, Maria A.

    2016-01-01

    The residual stress and microstrain distribution induced by laser beam welding of the low-alloyed C45 steel plate was investigated using high-resolution time-of-flight (TOF) neutron diffraction. The neutron diffraction experiments were performed on FSD diffractometer at the IBR-2 pulsed reactor in FLNP JINR (Dubna, Russia). The experiments have shown that the residual stress distribution across weld seam exhibit typical alternating sign character as it was observed in our previous studies. The residual stress level is varying in the range from -60 MPa to 450 MPa. At the same time, the microstrain level exhibits sharp maxima at weld seam position with maximal level of 4.8·10-3. The obtained experimental results are in good agreement with FEM calculations according to the STAAZ model. The provided numerical model validated with measured data enables to study the influence of different conditions and process parameters on the development of residual welding stresses.

  18. Phytoavailability and mechanism of bound PAH residues in filed contaminated soils.

    PubMed

    Gao, Yanzheng; Hu, Xiaojie; Zhou, Ziyuan; Zhang, Wei; Wang, Yize; Sun, Bingqing

    2017-03-01

    Understanding the phytoavailability of bound residues of polycyclic aromatic hydrocarbons (PAHs) in soils is essential to assessing their environmental fate and risks. This study investigated the release and plant uptake of bound PAH residues (reference to parent compounds) in field contaminated soils after the removal of extractable PAH fractions. Plant pot experiments were performed in a greenhouse using ryegrass (Lolium multiflorum Lam.) to examine the phytoavailablility of bound PAH residues, and microcosm incubation experiments with and without the addition of artificial root exudates (AREs) or oxalic acid were conducted to examine the effect of root exudates on the release of bound PAH residues. PAH accumulation in the ryegrass after a 50-day growth period indicated that bound PAH residues were significantly phytoavailable. The extractable fractions, including the desorbing and non-desorbing fractions, dominated the total PAH concentrations in vegetated soils after 50 days, indicating the transfer of bound PAH residues to the extractable fractions. This transfer was facilitated by root exudates. The addition of AREs and oxalic acid to test soils enhanced the release of bound PAH residues into their extractable fractions, resulting in enhanced phytoavailability of bound PAH residues in soils. This study provided important information regarding environmental fate and risks of bound PAH residues in soils. Copyright © 2016 Elsevier Ltd. All rights reserved.

  19. Residual stress measurement in a metal microdevice by micro Raman spectroscopy

    NASA Astrophysics Data System (ADS)

    Song, Chang; Du, Liqun; Qi, Leijie; Li, Yu; Li, Xiaojun; Li, Yuanqi

    2017-10-01

    Large residual stress induced during the electroforming process cannot be ignored to fabricate reliable metal microdevices. Accurate measurement is the basis for studying the residual stress. Influenced by the topological feature size of micron scale in the metal microdevice, residual stress in it can hardly be measured by common methods. In this manuscript, a methodology is proposed to measure the residual stress in the metal microdevice using micro Raman spectroscopy (MRS). To estimate the residual stress in metal materials, micron sized β-SiC particles were mixed in the electroforming solution for codeposition. First, the calculated expression relating the Raman shifts to the induced biaxial stress for β-SiC was derived based on the theory of phonon deformation potentials and Hooke’s law. Corresponding micro electroforming experiments were performed and the residual stress in Ni-SiC composite layer was both measured by x-ray diffraction (XRD) and MRS methods. Then, the validity of the MRS measurements was verified by comparing with the residual stress measured by XRD method. The reliability of the MRS method was further validated by the statistical student’s t-test. The MRS measurements were found to have no systematic error in comparison with the XRD measurements, which confirm that the residual stresses measured by the MRS method are reliable. Besides that, the MRS method, by which the residual stress in a micro inertial switch was measured, has been confirmed to be a convincing experiment tool for estimating the residual stress in metal microdevice with micron order topological feature size.

  20. Low-Residue and Low-Fiber Diets in Gastrointestinal Disease Management12

    PubMed Central

    Vanhauwaert, Erika; Matthys, Christophe; Verdonck, Lies; De Preter, Vicky

    2015-01-01

    Recently, low-residue diets were removed from the American Academy of Nutrition and Dietetics’ Nutrition Care Manual due to the lack of a scientifically accepted quantitative definition and the unavailability of a method to estimate the amount of food residue produced. This narrative review focuses on defining the similarities and/or discrepancies between low-residue and low-fiber diets and on the diagnostic and therapeutic values of these diets in gastrointestinal disease management. Diagnostically, a low-fiber/low-residue diet is used in bowel preparation. A bowel preparation is a cleansing of the intestines of fecal matter and secretions conducted before a diagnostic procedure. Therapeutically, a low-fiber/low-residue diet is part of the treatment of acute relapses in different bowel diseases. The available evidence on low-residue and low-fiber diets is summarized. The main findings showed that within human disease research, the terms “low residue” and “low fiber” are used interchangeably, and information related to the quantity of residue in the diet usually refers to the amount of fiber. Low-fiber/low-residue diets are further explored in both diagnostic and therapeutic situations. On the basis of this literature review, the authors suggest redefining a low-residue diet as a low-fiber diet and to quantitatively define a low-fiber diet as a diet with a maximum of 10 g fiber/d. A low-fiber diet instead of a low-residue diet is recommended as a diagnostic value or as specific therapy for gastrointestinal conditions. PMID:26567203

  1. 40 CFR 180.618 - Benthiavalicarb-isopropyl; tolerance for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... (CONTINUED) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific... established for the combined residues of benthiavalicarb-isopropyl, isopropyl[(S)-1-[[[(1R)-1-(6-fluoro-2...

  2. 40 CFR 180.618 - Benthiavalicarb-isopropyl; tolerance for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... (CONTINUED) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific... established for the combined residues of benthiavalicarb-isopropyl, isopropyl[(S)-1-[[[(1R)-1-(6-fluoro-2...

  3. Determination of cutin-bound residues of chlorothalonil by immunoassay.

    PubMed

    Jahn, C; Schwack, W

    2001-03-01

    An indirect competitive enzyme-linked immunosorbent assay (ELISA) was used to determine photochemically cutin-bound residues of chlorothalonil in enzymatically isolated tomato and apple fruit cuticles. The samples were spiked, irradiated, exhaustively extracted, and depolymerized with boron trifluoride complex resulting in a soluble depolymerisate. With this procedure, the ELISA could be calibrated with free target molecules for the quantification of originally bound chlorothalonil residues. In fruit cuticles that were irradiated for 8 h by simulated sunlight, 0.030 and 0.068 mg/g photoinduced cutin-bound residues of wax-free cuticles (calculated as chlorothalonil) were determined for tomatoes and apples, respectively. For the used antibody mAb chl. 4/11, cross-reactivities with derivatives of chlorothalonil simulating different types of cuticle-bound residues are given and discussed.

  4. Pesticide residues in imported, organic, and "suspect" fruits and vegetables.

    PubMed

    Winter, Carl K

    2012-05-09

    Consumers are frequently urged to avoid imported foods as well as specific fruits and vegetables due to health concerns from pesticide residues and are often encouraged to choose organic fruits and vegetables rather than conventional forms. Studies have demonstrated that while organic fruits and vegetables have lower levels of pesticide residues than do conventional fruits and vegetables, pesticide residues are still frequently detected on organic fruits and vegetables; typical dietary consumer exposure to pesticide residues from conventional fruits and vegetables does not appear to be of health significance. Similarly, research does not demonstrate that imported fruits and vegetables pose greater risks from pesticide residues than do domestic fruits and vegetables or that specific fruits and vegetables singled out as being the most highly contaminated by pesticides should be avoided in their conventional forms.

  5. 40 CFR 180.430 - Fenoxaprop-ethyl; tolerances for residues.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... residues of the herbicide fenoxaprop-ethyl, including its metabolites and degradates, in or on the... for residues of the herbicide fenoxaprop-ethyl, including its metabolites and degradates, in or on the...

  6. 40 CFR 180.430 - Fenoxaprop-ethyl; tolerances for residues.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... residues of the herbicide fenoxaprop-ethyl, including its metabolites and degradates, in or on the... for residues of the herbicide fenoxaprop-ethyl, including its metabolites and degradates, in or on the...

  7. ResidPlots-2: Computer Software for IRT Graphical Residual Analyses

    ERIC Educational Resources Information Center

    Liang, Tie; Han, Kyung T.; Hambleton, Ronald K.

    2009-01-01

    This article discusses the ResidPlots-2, a computer software that provides a powerful tool for IRT graphical residual analyses. ResidPlots-2 consists of two components: a component for computing residual statistics and another component for communicating with users and for plotting the residual graphs. The features of the ResidPlots-2 software are…

  8. Crop residues for advanced biofuels workshop: A synposis

    USDA-ARS?s Scientific Manuscript database

    Crop residues are being harvested for a variety of purposes including their use as livestock feed and to produce advanced biofuels. Crop residue harvesting, by definition, reduces the potential annual carbon input to the soil from aboveground biomass but does not affect input from plant roots. The m...

  9. 40 CFR 180.513 - Chlorfenapyr; tolerances for residues.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    .... Application excludes any direct application to any food, food packaging, or any food contact surfaces. (v) To...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances... residues of chlorfenapyr in or on all food commodities (other than those covered by a higher tolerance as a...

  10. 40 CFR 180.513 - Chlorfenapyr; tolerances for residues.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    .... Application excludes any direct application to any food, food packaging, or any food contact surfaces. (v) To...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances... residues of chlorfenapyr in or on all food commodities (other than those covered by a higher tolerance as a...

  11. 40 CFR 180.513 - Chlorfenapyr; tolerances for residues.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    .... Application excludes any direct application to any food, food packaging, or any food contact surfaces. (v) To...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances... residues of chlorfenapyr in or on all food commodities (other than those covered by a higher tolerance as a...

  12. 40 CFR 180.513 - Chlorfenapyr; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... after each use of the product. (iv) Contamination of food or food contact surfaces shall be avoided...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances... residues of chlorfenapyr in or on all food commodities (other than those covered by a higher tolerance as a...

  13. 40 CFR 180.293 - Endothall; tolerances for residues.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 0.2 parts per million is established for residues of the herbicide endothall (7 - oxabicyclo[2.2.1...-dimethylalkylamine, and mono-N-N,-dimethylalkylamine salts as algicides or herbicides to control aquatic plants in.... Tolerances are established for the indirect or inadvertent combined residues of the herbicide, endothall (7...

  14. 40 CFR 180.293 - Endothall; tolerances for residues.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 0.2 parts per million is established for residues of the herbicide endothall (7 - oxabicyclo[2.2.1...-dimethylalkylamine, and mono-N-N,-dimethylalkylamine salts as algicides or herbicides to control aquatic plants in.... Tolerances are established for the indirect or inadvertent combined residues of the herbicide, endothall (7...

  15. Monitoring of Pesticide Residues in Commonly Used Fruits and Vegetables in Kuwait.

    PubMed

    Jallow, Mustapha F A; Awadh, Dawood G; Albaho, Mohammed S; Devi, Vimala Y; Ahmad, Nisar

    2017-07-25

    The presence of pesticide residues in primary and derived agricultural products raises serious health concerns for consumers. The aim of this study was to assess the level of pesticide residues in commonly consumed fruits and vegetables in Kuwait. A total of 150 samples of different fresh vegetables and fruits were analyzed for the presence of 34 pesticides using the quick easy cheap effective rugged and safe (QuEChERS) multi-residue extraction, followed by gas chromatography-mass spectrometry (GC-MS) or liquid chromatography-tandem mass spectrometry (LC - MS / MS). Pesticide residues above the maximum residue limits (MRL) were detected in 21% of the samples and 79% of the samples had no residues of the pesticides surveyed or contained residues below the MRL. Multiple residues were present in 40% of the samples with two to four pesticides, and four samples were contaminated with more than four pesticide residues. Of the pesticides investigated, 16 were detected, of which imidacloprid, deltamethrin, cypermethrin, malathion, acetamiprid, monocrotophos, chlorpyrifos-methyl, and diazinon exceeded their MRLs. Aldrin, an organochlorine pesticide, was detected in one apple sample, with residues below the MRL. The results indicate the occurrence of pesticide residues in commonly consumed fruits and vegetables in Kuwait, and pointed to an urgent need to develop comprehensive intervention measures to reduce the potential health risk to consumers. The need for the regular monitoring of pesticide residues and the sensitization of farmers to better pesticide safety practices, especially the need to adhere to recommended pre-harvest intervals is recommended.

  16. Pesticide Residues and Bees – A Risk Assessment

    PubMed Central

    Sanchez-Bayo, Francisco; Goka, Koichi

    2014-01-01

    Bees are essential pollinators of many plants in natural ecosystems and agricultural crops alike. In recent years the decline and disappearance of bee species in the wild and the collapse of honey bee colonies have concerned ecologists and apiculturalists, who search for causes and solutions to this problem. Whilst biological factors such as viral diseases, mite and parasite infections are undoubtedly involved, it is also evident that pesticides applied to agricultural crops have a negative impact on bees. Most risk assessments have focused on direct acute exposure of bees to agrochemicals from spray drift. However, the large number of pesticide residues found in pollen and honey demand a thorough evaluation of all residual compounds so as to identify those of highest risk to bees. Using data from recent residue surveys and toxicity of pesticides to honey and bumble bees, a comprehensive evaluation of risks under current exposure conditions is presented here. Standard risk assessments are complemented with new approaches that take into account time-cumulative effects over time, especially with dietary exposures. Whilst overall risks appear to be low, our analysis indicates that residues of pyrethroid and neonicotinoid insecticides pose the highest risk by contact exposure of bees with contaminated pollen. However, the synergism of ergosterol inhibiting fungicides with those two classes of insecticides results in much higher risks in spite of the low prevalence of their combined residues. Risks by ingestion of contaminated pollen and honey are of some concern for systemic insecticides, particularly imidacloprid and thiamethoxam, chlorpyrifos and the mixtures of cyhalothrin and ergosterol inhibiting fungicides. More attention should be paid to specific residue mixtures that may result in synergistic toxicity to bees. PMID:24718419

  17. Forest Residues Bundling Project

    Treesearch

    U.S. Forest Service

    2007-01-01

    During the summer of 2003, the U.S. Forest Service conducted an evaluation of biomass bundling for forest residue extraction. This CD provides a report of the project results, a video documentary project record, and a collection of images from the project. Additional information is available at:

  18. Production of apple-based baby food: changes in pesticide residues.

    PubMed

    Kovacova, Jana; Kocourek, Vladimir; Kohoutkova, Jana; Lansky, Miroslav; Hajslova, Jana

    2014-01-01

    Apples represent the main component of most fruit-based baby food products. Since not only fruit from organic farming, but also conventionally grown fruit is used for baby food production, the occurrence of pesticide residues in the final product is of high concern. To learn more about the fate of these hazardous compounds during processing of contaminated raw material, apples containing altogether 21 pesticide residues were used for preparation of a baby food purée both in the household and at industrial scale (in the baby food production facility). Within both studies, pesticide residues were determined in raw apples as well as in final products. Intermediate product and by-product were also analysed during the industrial process. Determination of residues was performed by a sensitive multi-detection analytical method based on liquid or gas chromatography coupled with mass spectrometry. The household procedure involved mainly the cooking of unpeeled apples, and the decrease of residues was not extensive enough for most of the studied pesticides; only residues of captan, dithianon and thiram dropped significantly (processing factors less than 0.04). On the other hand, changes in pesticide levels were substantial for all tested pesticides during apple processing in the industrial baby food production facility. The most important operation affecting the reduction of residues was removal of the by-products after pulping (rest of the peel, stem, pips etc.), while subsequent sterilisation has an insignificant effect. Also in this case, captan, dithianon and thiram were identified as pesticides with the most evident decrease of residues.

  19. Measurement of Residual Flexibility for Substructures Having Prominent Flexible Interfaces

    NASA Technical Reports Server (NTRS)

    Tinker, Michael L.; Bookout, Paul S.

    1994-01-01

    Verification of a dynamic model of a constrained structure requires a modal survey test of the physical structure and subsequent modification of the model to obtain the best agreement possible with test data. Constrained-boundary or fixed-base testing has historically been the most common approach for verifying constrained mathematical models, since the boundary conditions of the test article are designed to match the actual constraints in service. However, there are difficulties involved with fixed-base testing, in some cases making the approach impractical. It is not possible to conduct a truly fixed-base test due to coupling between the test article and the fixture. In addition, it is often difficult to accurately simulate the actual boundary constraints, and the cost of designing and constructing the fixture may be prohibitive. For use when fixed-base testing proves impractical or undesirable, alternate free-boundary test methods have been investigated, including the residual flexibility technique. The residual flexibility approach has been treated analytically in considerable detail and has had limited frequency response measurements for the method. This concern is well-justified for a number of reasons. First, residual flexibilities are very small numbers, typically on the order of 1.0E-6 in/lb for translational diagonal terms, and orders of magnitude smaller for off-diagonal values. This poses difficulty in obtaining accurate and noise-free measurements, especially for points removed from the excitation source. A second difficulty encountered in residual measurements lies in obtaining a clean residual function in the process of subtracting synthesized modal data from a measured response function. Inaccuracies occur since modes are not subtracted exactly, but only to the accuracy of the curve fits for each mode; these errors are compounded with increasing distance from the excitation point. In this paper, the residual flexibility method is applied to a simple

  20. Utilization of organic residues using heterotrophic microalgae and insects.

    PubMed

    Pleissner, Daniel; Rumpold, Birgit A

    2018-02-01

    Various organic residues occur globally in the form of straw, wood, green biomass, food waste, feces, manure etc. Other utilization strategies apart from anaerobic digestion, composting and incineration are needed to make use of the whole potential of organic residues as sources of various value added compounds. This review compares the cultivation of heterotrophic microalgae and insects using organic residues as nutrient sources and illuminates their potential with regard to biomass production, productivity and yield, and utilization strategies of produced biomasses. Furthermore, cultivation processes as well as advantages and disadvantages of utilization processes are identified and discussed. It was shown that both heterotrophic algae and insects are able to reduce a sufficient amount of organic residues by converting it into biomass. The biomass composition of both organisms is similar which allows similar utilization strategies in food and feed, chemicals and materials productions. Even though insect is the more complex organism, biomass production can be carried out using simple equipment without sterilization and hydrolysis of organic residues. Contrarily, heterotrophic microalgae require a pretreatment of organic residues in form of sterilization and in most cases hydrolysis. Interestingly, the volumetric productivity of insect biomass exceeds the productivity of algal biomass. Despite legal restrictions, it is expected that microalgae and insects will find application as alternative food and feed sources in the future. Copyright © 2017 Elsevier Ltd. All rights reserved.

  1. OECD Maximum Residue Limit Calculator

    EPA Pesticide Factsheets

    With the goal of harmonizing the calculation of maximum residue limits (MRLs) across the Organisation for Economic Cooperation and Development, the OECD has developed an MRL Calculator. View the calculator.

  2. Prospecting for Energy-Rich Renewable Raw Materials: Sorghum Stem Case Study.

    PubMed

    Byrt, Caitlin S; Betts, Natalie S; Tan, Hwei-Ting; Lim, Wai Li; Ermawar, Riksfardini A; Nguyen, Hai Yen; Shirley, Neil J; Lahnstein, Jelle; Corbin, Kendall; Fincher, Geoffrey B; Knauf, Vic; Burton, Rachel A

    2016-01-01

    Sorghum vegetative tissues are becoming increasingly important for biofuel production. The composition of sorghum stem tissues is influenced by genotype, environment and photoperiod sensitivity, and varies widely between varieties and also between different stem tissues (outer rind vs inner pith). Here, the amount of cellulose, (1,3;1,4)-β-glucan, arabinose and xylose in the stems of twelve diverse sorghum varieties, including four photoperiod-sensitive varieties, was measured. At maturity, most photoperiod-insensitive lines had 1% w/w (1,3;1,4)-β-glucan in stem pith tissue whilst photoperiod-sensitive varieties remained in a vegetative stage and accumulated up to 6% w/w (1,3;1,4)-β-glucan in the same tissue. Three sorghum lines were chosen for further study: a cultivated grain variety (Sorghum bicolor BTx623), a sweet variety (S. bicolor Rio) and a photoperiod-sensitive wild line (S. bicolor ssp. verticilliflorum Arun). The Arun line accumulated 5.5% w/w (1,3;1,4)-β-glucan and had higher SbCslF6 and SbCslH3 transcript levels in pith tissues than did photoperiod-insensitive varieties Rio and BTx623 (<1% w/w pith (1,3;1,4)-β-glucan). To assess the digestibility of the three varieties, stem tissue was treated with either hydrolytic enzymes or dilute acid and the release of fermentable glucose was determined. Despite having the highest lignin content, Arun yielded significantly more glucose than the other varieties, and theoretical calculation of ethanol yields was 10 344 L ha-1 from this sorghum stem tissue. These data indicate that sorghum stem (1,3;1,4)-β-glucan content may have a significant effect on digestibility and bioethanol yields. This information opens new avenues of research to generate sorghum lines optimised for biofuel production.

  3. Agmatine, an endogenous ligand at imidazoline binding sites, does not antagonize the clonidine-mediated blood pressure reaction

    PubMed Central

    Raasch, Walter; Schäfer, Ulrich; Qadri, Fatimunnisa; Dominiak, Peter

    2002-01-01

    Since agmatine has been identified as a clonidine displacing substance (CDS), the aim of this study was to investigate whether agmatine can mimic CDS-induced cardiovascular reactions in organ bath experiments, pithed spontaneously hypertensive rats (SHR) and anaesthetized SHR.Intravenously-administered agmatine significantly reduced the blood pressure and heart rate of anaesthetized SHR at doses higher than 1 and 3 mg kg−1, respectively. These effects are probably mediated via central mechanisms, since there was an approximate 8 fold rightward shift of the dose-response curve in the pithed SHR (indicating a weakened cardiovascular effect). Moreover, in organ bath experiments, agmatine failed to alter the contractility of intact or endothelium-denuded aortal rings. When agmatine was administered i.c.v. to anaesthetized SHR, blood pressure was increased without any alteration of heart rate, whereas blood pressure was unchanged and heart rate was increased after injection into the 4th brain ventricle. This suggests that haemodynamic reaction patterns after central application are related to distinct influences on central cardiovascular mechanisms.Agmatine reduces noradrenaline release in pithed SHR while α2-adrenoceptors are irreversibly blocked with phenoxybenzamine, but not while I1-binding sites are selectively blocked with AGN192403. This suggests that agmatine may modulate noradrenaline release in the same way that clonidine does, i.e. via imidazoline binding sites; this involves a reduction in sympathetic tone which in turn reduces blood pressure and heart rate.Finally, CDS-like cardiovascular activity appears not to be due to agmatine, since (i) blood pressure in anaesthetized SHR is decreased by agmatine and clonidine, and (ii) agmatine did not antagonize the blood pressure reaction to clonidine in pithed or anaesthetized SHR. PMID:11834614

  4. Helicoverpa zea (Lepidoptera: Noctuidae) and Spodoptera frugiperda (Lepidoptera: Noctuidae) Responses to Sorghum bicolor (Poales: Poaceae) Tissues From Lowered Lignin Lines.

    PubMed

    Dowd, Patrick F; Sattler, Scott E

    2015-01-01

    The presence of lignin within biomass impedes the production of liquid fuels. Plants with altered lignin content and composition are more amenable to lignocellulosic conversion to ethanol and other biofuels but may be more susceptible to insect damage where lignin is an important resistance factor. However, reduced lignin lines of switchgrasses still retained insect resistance in prior studies. Therefore, we hypothesized that sorghum lines with lowered lignin content will also retain insect resistance. Sorghum excised leaves and stalk pith Sorghum bicolor (L.) Moench (Poales: Poaceae) from near isogenic brown midrib (bmr) 6 and 12 mutants lines, which have lowered lignin content and increased lignocellulosic ethanol conversion efficiency, were examined for insect resistance relative to wild-type (normal BTx623). Greenhouse and growth chamber grown plant tissues were fed to first-instar larvae of corn earworms, Helicoverpa zea (Boddie) and fall armyworms Spodoptera frugiperda (J.E. Smith) (Lepidoptera: Noctuidae), two sorghum major pests. Younger bmr leaves had significantly greater feeding damage in some assays than wild-type leaves, but older bmr6 leaves generally had significantly less damage than wild-type leaves. Caterpillars feeding on the bmr6 leaves often weighed significantly less than those feeding on wild-type leaves, especially in the S. frugiperda assays. Larvae fed the pith from bmr stalks had significantly higher mortality compared with those larvae fed on wild-type pith, which suggested that bmr pith was more toxic. Thus, reducing lignin content or changing subunit composition of bioenergy grasses does not necessarily increase their susceptibility to insects and may result in increased resistance, which would contribute to sustainable production. Published by Oxford University Press on behalf of the Entomological Society of America 2015. This work is written by US Government employees and is in the public domain in the US.

  5. Residual Wage Differences by Gender: Bounding the Estimates.

    ERIC Educational Resources Information Center

    Sakellariou, Chris N.; Patrinos, Harry A.

    1996-01-01

    Uses data from the 1986 Canadian labor market activity survey file to derive estimates of residual gender wage gap differences. Investigates these estimates' dependence on experimental design and on assumptions about discrimination-free wage structures. Residual differences persist, even after restricting the sample to a group of highly motivated,…

  6. 40 CFR 180.505 - Emamectin; tolerances for residues.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 25 2013-07-01 2013-07-01 false Emamectin; tolerances for residues... § 180.505 Emamectin; tolerances for residues. (a) General. (1) Tolerances are established for emamectin... tolerance levels specified below is to be determined by measuring only the sum of emamectin (a mixture of a...

  7. 40 CFR 180.505 - Emamectin; tolerances for residues.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 24 2014-07-01 2014-07-01 false Emamectin; tolerances for residues... § 180.505 Emamectin; tolerances for residues. (a) General. (1) Tolerances are established for emamectin... tolerance levels specified below is to be determined by measuring only the sum of emamectin (a mixture of a...

  8. Forest residues management guidelines for the Pacific Northwest.

    Treesearch

    John M. Pierovich; Edward H. Clarke; Stewart G. Pickford; Franklin R. Ward

    1975-01-01

    Forest residues often require treatment to meet land management objectives. Guideline statements for managing forest residues are presented to provide direction for achieving these objectives. The latest research information and the best knowledge of experts in various land management disciplines were used to formulate these statements. A unique keying system is...

  9. 40 CFR 180.412 - Sethoxydim; tolerances for residues.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... residues of the herbicide 2-[1-(ethoxyimino)butyl]-5-[2-(ethylthio)propyl]-3-hydroxy-2-cyclohexen-1-one... the herbicide) in or on the following commodities: Commodity Parts per million Alfalfa, forage 40... established for the combined residues of the herbicide 2-[1-(ethoxyimino)butyl]-5-[2-(ethylthio)propyl]-3...

  10. 40 CFR 180.184 - Linuron; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... herbicide linuron (3-(3,4-dichlorophenyl)-1-methoxy-1-methylurea) and its metabolites convertible to 3,4... tolerances specified in the following table are established for combined residues of the herbicide linuron (3... established for the combined residues of the herbicide linuron (3-(3,4-dichlorophenyl)-1-methoxy-1-methylurea...

  11. 40 CFR 180.184 - Linuron; tolerances for residues.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... herbicide linuron (3-(3,4-dichlorophenyl)-1-methoxy-1-methylurea) and its metabolites convertible to 3,4... tolerances specified in the following table are established for combined residues of the herbicide linuron (3... established for the combined residues of the herbicide linuron (3-(3,4-dichlorophenyl)-1-methoxy-1-methylurea...

  12. 40 CFR 180.412 - Sethoxydim; tolerances for residues.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... residues of the herbicide 2-[1-(ethoxyimino)butyl]-5-[2-(ethylthio)propyl]-3-hydroxy-2-cyclohexen-1-one... the herbicide) in or on the following commodities: Commodity Parts per million Alfalfa, forage 40... established for the combined residues of the herbicide 2-[1-(ethoxyimino)butyl]-5-[2-(ethylthio)propyl]-3...

  13. 40 CFR 180.412 - Sethoxydim; tolerances for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... residues of the herbicide 2-[1-(ethoxyimino)butyl]-5-[2-(ethylthio)propyl]-3-hydroxy-2-cyclohexen-1-one... the herbicide) in or on the following commodities: Commodity Parts per million Alfalfa, forage 40... established for the combined residues of the herbicide 2-[1-(ethoxyimino)butyl]-5-[2-(ethylthio)propyl]-3...

  14. 40 CFR 180.420 - Fluridone; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... (free and bound) of the herbicide fluridone (1-methyl-3-phenyl-5-[3-trifluoromethyl)phenyl]-4(1H)-5-[3... established for residues of the herbicide fluridone in the following raw agricultural commodities: Commodity... following irrigated crops and crop groupings for residues of the herbicide fluridone resulting from use of...

  15. 40 CFR 180.412 - Sethoxydim; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... residues of the herbicide 2-[1-(ethoxyimino)butyl]-5-[2-(ethylthio)propyl]-3-hydroxy-2-cyclohexen-1-one... the herbicide) in or on the following commodities: Commodity Parts per million Alfalfa, forage 40... the combined residues of the herbicide 2-[1-(ethoxyimino)butyl]-5-[2-(ethylthio)propyl]-3-hydroxy-2...

  16. 40 CFR 180.184 - Linuron; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... herbicide linuron (3-(3,4-dichlorophenyl)-1-methoxy-1-methylurea) and its metabolites convertible to 3,4... tolerances specified in the following table are established for combined residues of the herbicide linuron (3... established for the combined residues of the herbicide linuron (3-(3,4-dichlorophenyl)-1-methoxy-1-methylurea...

  17. 40 CFR 180.412 - Sethoxydim; tolerances for residues.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... residues of the herbicide 2-[1-(ethoxyimino)butyl]-5-[2-(ethylthio)propyl]-3-hydroxy-2-cyclohexen-1-one... the herbicide) in or on the following commodities: Commodity Parts per million Alfalfa, forage 40... established for the combined residues of the herbicide 2-[1-(ethoxyimino)butyl]-5-[2-(ethylthio)propyl]-3...

  18. 40 CFR 180.184 - Linuron; tolerances for residues.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... herbicide linuron (3-(3,4-dichlorophenyl)-1-methoxy-1-methylurea) and its metabolites convertible to 3,4... tolerances specified in the following table are established for combined residues of the herbicide linuron (3... established for the combined residues of the herbicide linuron (3-(3,4-dichlorophenyl)-1-methoxy-1-methylurea...

  19. 40 CFR 180.293 - Endothall; tolerances for residues.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... established for residues of the herbicide endothall (7 - oxabicyclo[2.2.1] heptane-2,3-dicarboxylic acid) in...,-dimethylalkylamine salts as algicides or herbicides to control aquatic plants in canals, lakes, ponds, and other... indirect or inadvertent combined residues of the herbicide, endothall (7 - oxabicyclo[2.2.1] heptane-2,3...

  20. 40 CFR 180.482 - Tebufenozide; tolerances for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...-dimethylethyl)-2-(4-ethylbenzoyl)hydrazide, the stearic acid conjugate of benzoic acid, 3-hydroxymethyl,5-methyl... residues of the insecticide tebufenozide, benzoic acid, 3,5-dimethyl-1-(1,1-dimethylethyl)-2-(4... established for the combined residues of tebufenozide and its metabolites benzoic acid, 3,5-dimethyl-1-(1,1...

  1. 40 CFR 180.180 - Orthoarsenic acid; tolerance for residues.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances..., 1995, for combined As 2O 3 is established for residues of the defoliant orthoarsenic acid in or on the...

  2. 40 CFR 180.180 - Orthoarsenic acid; tolerance for residues.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances..., 1995, for combined As 2O 3 is established for residues of the defoliant orthoarsenic acid in or on the...

  3. Catalytic combustion of residual fuels

    NASA Technical Reports Server (NTRS)

    Bulzan, D. L.; Tacina, R. R.

    1981-01-01

    A noble metal catalytic reactor was tested using two grades of petroleum derived residual fuels at specified inlet air temperatures, pressures, and reference velocities. Combustion efficiencies greater than 99.5 percent were obtained. Steady state operation of the catalytic reactor required inlet air temperatures of at least 800 K. At lower inlet air temperatures, upstream burning in the premixing zone occurred which was probably caused by fuel deposition and accumulation on the premixing zone walls. Increasing the inlet air temperature prevented this occurrence. Both residual fuels contained about 0.5 percent nitrogen by weight. NO sub x emissions ranged from 50 to 110 ppm by volume at 15 percent excess O2. Conversion of fuel-bound nitrogen to NO sub x ranged from 25 to 50 percent.

  4. 40 CFR 158.270 - Experimental use permit data requirements for residue chemistry.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... requirements for residue chemistry. 158.270 Section 158.270 Protection of Environment ENVIRONMENTAL PROTECTION... Experimental use permit data requirements for residue chemistry. All residue chemistry data, as described in... section 408(r) is sought. Residue chemistry data are not required for an experimental use permit issued on...

  5. 40 CFR 158.270 - Experimental use permit data requirements for residue chemistry.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... requirements for residue chemistry. 158.270 Section 158.270 Protection of Environment ENVIRONMENTAL PROTECTION... Experimental use permit data requirements for residue chemistry. All residue chemistry data, as described in... section 408(r) is sought. Residue chemistry data are not required for an experimental use permit issued on...

  6. 40 CFR 158.270 - Experimental use permit data requirements for residue chemistry.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... requirements for residue chemistry. 158.270 Section 158.270 Protection of Environment ENVIRONMENTAL PROTECTION... Experimental use permit data requirements for residue chemistry. All residue chemistry data, as described in... section 408(r) is sought. Residue chemistry data are not required for an experimental use permit issued on...

  7. 40 CFR 158.270 - Experimental use permit data requirements for residue chemistry.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... requirements for residue chemistry. 158.270 Section 158.270 Protection of Environment ENVIRONMENTAL PROTECTION... Experimental use permit data requirements for residue chemistry. All residue chemistry data, as described in... section 408(r) is sought. Residue chemistry data are not required for an experimental use permit issued on...

  8. 40 CFR 158.270 - Experimental use permit data requirements for residue chemistry.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... requirements for residue chemistry. 158.270 Section 158.270 Protection of Environment ENVIRONMENTAL PROTECTION... Experimental use permit data requirements for residue chemistry. All residue chemistry data, as described in... section 408(r) is sought. Residue chemistry data are not required for an experimental use permit issued on...

  9. Atomic structure of recombinant thaumatin II reveals flexible conformations in two residues critical for sweetness and three consecutive glycine residues.

    PubMed

    Masuda, Tetsuya; Mikami, Bunzo; Tani, Fumito

    2014-11-01

    Thaumatin, an intensely sweet-tasting protein used as a sweetener, elicits a sweet taste at 50 nM. Although two major variants designated thaumatin I and thaumatin II exist in plants, there have been few dedicated thaumatin II structural studies and, to date, data beyond atomic resolution had not been obtained. To identify the detailed structural properties explaining why thaumatin elicits a sweet taste, the structure of recombinant thaumatin II was determined at the resolution of 0.99 Å. Atomic resolution structural analysis with riding hydrogen atoms illustrated the differences in the direction of the side-chains more precisely and the electron density maps of the C-terminal regions were markedly improved. Though it had been suggested that the three consecutive glycine residues (G142-G143-G144) have highly flexible conformations, G143, the central glycine residue was successfully modelled in two conformations for the first time. Furthermore, the side chain r.m.s.d. values for two residues (R67 and R82) critical for sweetness exhibited substantially higher values, suggesting that these residues are highly disordered. These results demonstrated that the flexible conformations in two critical residues favoring their interaction with sweet taste receptors are prominent features of the intensely sweet taste of thaumatin. Copyright © 2014 Elsevier B.V. and Société française de biochimie et biologie Moléculaire (SFBBM). All rights reserved.

  10. Non-destructive measurement and role of surface residual stress monitoring in residual life assessment of a steam turbine blading material

    NASA Astrophysics Data System (ADS)

    Prabhu-Gaunkar, Gajanana; Rawat, M. S.; Prasad, C. R.

    2014-02-01

    Steam turbine blades in power generation equipment are made from martensitic stainless steels having high strength, good toughness and corrosion resistance. However, these steels are susceptible to pitting which can promote early failures of blades in the turbines, particularly in the low pressure dry/wet areas by stress corrosion and corrosion fatigue. Presence of tensile residual stresses is known to accelerate failures whereas compressive stresses can help in delaying failures. Shot peening has been employed as an effective tool to induce compressive residual stresses which offset a part of local surface tensile stresses in the surface layers of components. Maintaining local stresses at stress raisers, such as pits formed during service, below a threshold level can help in preventing the initiation microcracks and failures. The thickness of the layer in compression will, however, depend of the shot peening parameters and should extend below the bottom of corrosion pits. The magnitude of surface compressive drops progressively during service exposure and over time the effectiveness of shot peening is lost making the material susceptible to micro-crack initiation once again. Measurement and monitoring of surface residual stress therefore becomes important for assessing residual life of components in service. This paper shows the applicability of surface stress monitoring to life assessment of steam turbine blade material based on data generated in laboratory on residual surface stress measurements in relation to fatigue exposure. An empirical model is proposed to calculate the remaining life of shot peened steam turbine blades in service.

  11. Determination of transfer rate and nature of the residue(s) in milk from {sup 14}C-atrazine cows

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Thalacker, F.W.; Ash, S.G.; Simoneaux, B.J.

    1996-10-01

    In order to determine the rate of transfer and the nature of the atrazine residues present in milk, lactating dairy cattle were treated with atrazine at three concentrations, 0.764 ppm, 0.0747 ppm and 0.0085 ppm (dry weight of food consumed). The concentrations were selected to bridge the gap between the concentration used for EPA metabolism studies (10 ppm) and the potential exposure level of dairy cattle to atrazine and its chlorotriazine metabolites through feed. The cattle were dosed following the morning milking for nine consecutive days with a single capsule bolus of {sup 14}C-atrazine. Milk was collected twice daily andmore » aliquots of each milking and the individual cow`s daily pool of milk were analyzed by liquid scinitllation counting (LSC). The concentrations of {sup 14}C-residues in the milk plateaued on approximately day 3 and the mean {sup 14}C-atrazine levels in milk were 11.2 ppb, 1.13 ppb and 0.152 ppb for the high, middle and low dosed animals, respectively. The transfer of radioactive level of exposure to {sup 14}C-atrazine. The nature of the residues in milk were determined by extracting milk samples and analysis by HPLC, TLC or Aminex chromatography. Diaminchlorotriazine was the only chlorinated metabolite in the milk, constituting approximately 65% to 75% of the total radioactive residues (TRR).« less

  12. Control of Transmembrane Helix Dynamics by Interfacial Tryptophan Residues.

    PubMed

    McKay, Matthew J; Martfeld, Ashley N; De Angelis, Anna A; Opella, Stanley J; Greathouse, Denise V; Koeppe, Roger E

    2018-06-05

    Transmembrane protein domains often contain interfacial aromatic residues, which may play a role in the insertion and stability of membrane helices. Residues such as Trp or Tyr, therefore, are often found situated at the lipid-water interface. We have examined the extent to which the precise radial locations of interfacial Trp residues may influence peptide helix orientation and dynamics. To address these questions, we have modified the GW 5,19 ALP23 (acetyl-GGALW 5 (LA) 6 LW 19 LAGA-[ethanol]amide) model peptide framework to relocate the Trp residues. Peptide orientation and dynamics were analyzed by means of solid-state nuclear magnetic resonance (NMR) spectroscopy to monitor specific 2 H- and 15 N-labeled residues. GW 5,19 ALP23 adopts a defined, tilted orientation within lipid bilayer membranes with minimal evidence of motional averaging of NMR observables, such as 2 H quadrupolar or 15 N- 1 H dipolar splittings. Here, we examine how peptide dynamics are impacted by relocating the interfacial Trp (W) residues on both ends and opposing faces of the helix, for example by a 100° rotation on the helical wheel for positions 4 and 20. In contrast to GW 5,19 ALP23, the modified GW 4,20 ALP23 helix experiences more extensive motional averaging of the NMR observables in several lipid bilayers of different thickness. Individual and combined Gaussian analyses of the 2 H and 15 N NMR signals confirm that the extent of dynamic averaging, particularly rotational "slippage" about the helix axis, is strongly coupled to the radial distribution of the interfacial Trp residues as well as the bilayer thickness. Additional 2 H labels on alanines A3 and A21 reveal partial fraying of the helix ends. Even within the context of partial unwinding, the locations of particular Trp residues around the helix axis are prominent factors for determining transmembrane helix orientation and dynamics within the lipid membrane environment. Copyright © 2018 Biophysical Society. Published by

  13. Monitoring of pesticide residues in vegetarian diet.

    PubMed

    Kumari, Beena; Kathpal, T S

    2009-04-01

    Samples (28) of complete vegetarian diet consumed from morning till night i.e. tea, milk, breakfast, lunch, snacks, dinner, sweet dish etc. were collected from homes, hostels and hotels periodically from Hisar and analysed for detecting the residues of organochlorine, synthetic pyrethriod, organophosphate and carbamate insecticides. The estimation was carried out by using multi-residue analytical technique employing gas chromatograph (GC)-electron capture detector and GC-nitrogen phosphorous detector systems equipped with capillary columns. The whole diet sample was macerated in a mixer grinder and a representative sample in duplicate was analyzed for residues keeping the average daily diet of an adult to be 1,300 g. On comparing the data, it was found that actual daily intake (microgram/person/day) of lindane in two and endosulfan in four samples exceeded the acceptable daily intake. Residues of other pesticides in all the diet samples were lower than the acceptable daily intake (ADI) of the respective pesticides. The study concluded that although all the diet samples were found contaminated with one or the other pesticide, the actual daily intake of only a few pesticides was higher than their respective ADI. More extensive study covering other localities of Haryana has been suggested to know the overall scenario of contamination of vegetarian diet.

  14. Amplified effect of mild plastic anisotropy on residual stress and strain anisotropy

    DOE PAGES

    Prime, Michael B.

    2017-07-01

    Axisymmetric indentation of a geometrically axisymmetric disk produced residual stresses by non-uniform plastic deformation. The 2024 aluminum plate used to make the disk exhibited mild plastic anisotropy with about 10% lower strength in the transverse direction compared to the rolling and through-thickness directions. Residual stresses and strains in the disk were measured with neutron diffraction, slitting, the contour method, x-ray diffraction and hole drilling. Surprisingly, the residual-stress anisotropy measured in the disk was about 40%, the residual-strain anisotropy was an impressive 100%, and the residual stresses were higher in the weaker direction. The high residual stress anisotropy relative to themore » mild plastic anisotropy and the direction of the highest stress are explained by considering the mechanics of indentation: constraint on deformation provided by the material surrounding the indentation and preferential deformation in the most compliant direction for incremental deformation. By contrast, the much larger anisotropy in residual strain compared to that in residual stress is independent of the fabrication process and is instead explained by considering Hookean elasticity. For Poisson's ratio of 1/3, the relationship simplifies to the residual strain anisotropy equaling the square of the residual stress anisotropy, which matches the observed results (2 ≈ 1.4^2). Furthermore, a lesson from this study is that to accurately predict residual stresses and strains, one must be wary of seemingly reasonable simplifying assumptions such as neglecting mild plastic anisotropy.« less

  15. Amplified effect of mild plastic anisotropy on residual stress and strain anisotropy

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Prime, Michael B.

    Axisymmetric indentation of a geometrically axisymmetric disk produced residual stresses by non-uniform plastic deformation. The 2024 aluminum plate used to make the disk exhibited mild plastic anisotropy with about 10% lower strength in the transverse direction compared to the rolling and through-thickness directions. Residual stresses and strains in the disk were measured with neutron diffraction, slitting, the contour method, x-ray diffraction and hole drilling. Surprisingly, the residual-stress anisotropy measured in the disk was about 40%, the residual-strain anisotropy was an impressive 100%, and the residual stresses were higher in the weaker direction. The high residual stress anisotropy relative to themore » mild plastic anisotropy and the direction of the highest stress are explained by considering the mechanics of indentation: constraint on deformation provided by the material surrounding the indentation and preferential deformation in the most compliant direction for incremental deformation. By contrast, the much larger anisotropy in residual strain compared to that in residual stress is independent of the fabrication process and is instead explained by considering Hookean elasticity. For Poisson's ratio of 1/3, the relationship simplifies to the residual strain anisotropy equaling the square of the residual stress anisotropy, which matches the observed results (2 ≈ 1.4^2). Furthermore, a lesson from this study is that to accurately predict residual stresses and strains, one must be wary of seemingly reasonable simplifying assumptions such as neglecting mild plastic anisotropy.« less

  16. Studies on pyrolysis and gasification of automobile shredder residue in China.

    PubMed

    Ni, Feijian; Chen, Ming

    2014-10-01

    With increasing automobile ownerships in China, the number of end-of-life vehicles has also rapidly increased. However, the automobile shredder residue generated during the dismantling of end-of-life vehicles in China is not treated properly and has caused great resource waste and environmental problems. In this work, automobile shredder residue from a domestic end-of-life vehicles dismantling company was comprehensively studied through element analysis, combustion heat experiment, proximate analysis, and thermogravimetric analysis. The feasibility of using pyrolysis combined with gasification to treat and recycle automobile shredder residue was investigated. The produced gas, oil, and residue yield was measured and the correlation between their yield and the experimental temperature and ratio of air to automobile shredder residue feed was studied. It is found that when ratio of air and experimental temperature are 1.5 mol kg(-1) and 900 °C, respectively, the heat energy of the gas produced per kilogram treated automobile shredder residue reaches a maximum value of 11.28 MJ. The characteristics of pyrolysis oil and solid residue were studied. The solid residue takes up 4.65%~5.57% of the original end-of-life vehicles weight. This greatly helps to reach the target of a 95% recycling rate. © The Author(s) 2014.

  17. Therapeutic and nutraceutical potential of bioactive compounds extracted from fruit residues.

    PubMed

    Babbar, Neha; Oberoi, Harinder Singh; Sandhu, Simranjeet Kaur

    2015-01-01

    The growing interest in the substitution of synthetic food antioxidants by natural ones has fostered research in identifying new low-cost antioxidants having commercial potential. Fruits such as mango, banana, and those belonging to the citrus family leave behind a substantial amount of residues in the form of peels, pulp, seeds, and stones. Due to lack of infrastructure to handle a huge quantity of available biomass, lack of processing facilities, and high processing cost, these residues represent a major disposal problem, especially in developing countries. Because of the presence of phenolic compounds, which impart nutraceutical properties to fruit residues, such residues hold tremendous potential in food, pharmaceutical, and cosmetic industries. The biological properties such as anticarcinogenicity, antimutagenicity, antiallergenicity, and antiageing activity have been reported for both natural as well as synthetic antioxidants. Special attention is focused on extraction of bioactive compounds from inexpensive or residual sources. The purpose of this review is to characterize different phenolics present in the fruit residues, discuss the antioxidant potential of such residues and the assays used in determination of antioxidant properties, discuss various methods for efficient extraction of the bioactive compounds, and highlight the importance of fruit residues as potential nutraceutical resources and biopreservatives.

  18. Crop residue decomposition in Minnesota biochar-amended plots

    NASA Astrophysics Data System (ADS)

    Weyers, S. L.; Spokas, K. A.

    2014-06-01

    Impacts of biochar application at laboratory scales are routinely studied, but impacts of biochar application on decomposition of crop residues at field scales have not been widely addressed. The priming or hindrance of crop residue decomposition could have a cascading impact on soil processes, particularly those influencing nutrient availability. Our objectives were to evaluate biochar effects on field decomposition of crop residue, using plots that were amended with biochars made from different plant-based feedstocks and pyrolysis platforms in the fall of 2008. Litterbags containing wheat straw material were buried in July of 2011 below the soil surface in a continuous-corn cropped field in plots that had received one of seven different biochar amendments or a uncharred wood-pellet amendment 2.5 yr prior to start of this study. Litterbags were collected over the course of 14 weeks. Microbial biomass was assessed in treatment plots the previous fall. Though first-order decomposition rate constants were positively correlated to microbial biomass, neither parameter was statistically affected by biochar or wood-pellet treatments. The findings indicated only a residual of potentially positive and negative initial impacts of biochars on residue decomposition, which fit in line with established feedstock and pyrolysis influences. Overall, these findings indicate that no significant alteration in the microbial dynamics of the soil decomposer communities occurred as a consequence of the application of plant-based biochars evaluated here.

  19. Crop residue decomposition in Minnesota biochar amended plots

    NASA Astrophysics Data System (ADS)

    Weyers, S. L.; Spokas, K. A.

    2014-02-01

    Impacts of biochar application at laboratory scales are routinely studied, but impacts of biochar application on decomposition of crop residues at field scales have not been widely addressed. The priming or hindrance of crop residue decomposition could have a cascading impact on soil processes, particularly those influencing nutrient availability. Our objectives were to evaluate biochar effects on field decomposition of crop residue, using plots that were amended with biochars made from different feedstocks and pyrolysis platforms prior to the start of this study. Litterbags containing wheat straw material were buried below the soil surface in a continuous-corn cropped field in plots that had received one of seven different biochar amendments or a non-charred wood pellet amendment 2.5 yr prior to start of this study. Litterbags were collected over the course of 14 weeks. Microbial biomass was assessed in treatment plots the previous fall. Though first-order decomposition rate constants were positively correlated to microbial biomass, neither parameter was statistically affected by biochar or wood-pellet treatments. The findings indicated only a residual of potentially positive and negative initial impacts of biochars on residue decomposition, which fit in line with established feedstock and pyrolysis influences. Though no significant impacts were observed with field-weathered biochars, effective soil management may yet have to account for repeat applications of biochar.

  20. Residual Strain in PCBs with Cu-Plated Holes

    NASA Astrophysics Data System (ADS)

    Rudajevova, A.; Dušek, K.

    2017-12-01

    The residual strain in pure printed circuit boards (PCBs) and PCBs with Cu-plated holes has been obtained by measurement of the temperature dependence of their dilatational characteristics in the x, y, and z directions up to 240°C. Shrinkage in all directions was observed for all samples of both materials in the first thermal cycle. No permanent length changes were observed in the second or subsequent thermal cycles. The residual strain was determined from the difference in relative elongation between the first and second thermal cycles. Relaxation of residual strain occurred only in the first thermal cycle, as a thermally activated process. The highest value of relaxed residual strain was found in the z direction for both materials. Relaxation of residual strain in the z direction of the pure PCB occurred only in the negative strain range, whereas relaxation of the PCB with Cu-plated holes occurred in both the positive and negative strain ranges. The relaxation of the positive strain in the PCB with Cu-plated holes in the z direction implies that this part of the PCB was under pressure during its preparation. This relaxation is a consequence of the high coefficient of thermal expansion of PCB laminate in this direction, which can also lead to cracks in Cu holes when the material is heated above the glass-transition temperature.